Secondary electron images obtained with a standard PEEM set up

International Nuclear Information System (INIS)

Benka, O.; Zeppenfeld, P.

2004-01-01

Secondary electron images excited by 3 to 4.3 keV electrons are obtained with a standard photoelectron electron emission microscope (PEEM) set up equipped with an imaging energy filter (IEF). The electron gun was mounted on a standard PEEM entrance flange at an angle of 25 o with respect to the sample surface. A low extraction voltage of 500 V was used to minimize the deflection of the electron beam by the PEEM extraction electrode. The secondary electron images are compared to photoelectron images excited by a standard 4.9 eV UV lamp. In the case of a Cu pattern on a Si substrate it is found that the lateral resolution without the IEF is about the same for electron and photon excitation but that the relative electron emission intensities are very different. The use of the IEF-reduces the lateral resolution. Images for secondary electron energies between eV 1 and eV 2 were obtained by setting the IEF to -V 1 and -V 2 ∼ -(V 1 + 5V) potentials and taking the difference of both images. Images up to 100 eV electron energies were recorded. The lateral resolution is in the range of μm. The material contrast obtained in these difference images are discussed in terms of a secondary electron and photoelectron emission model and secondary electron energy spectra measured with a LEED-Auger spectrometer. (author)

Experimental evaluation of tritium permeation through stainless steel tubes of heat exchanger from primary to secondary water in ITER

International Nuclear Information System (INIS)

Nakamura, Hirofumi; Nishi, Masataka

2004-01-01

Tritium permeation through heat exchanger from primary cooling water to secondary cooling water has been investigated experimentally with SS316L heat exchanger under simulated ITER (international thermonuclear experimental reactor) operation condition in order to establish the tritium permeation evaluation method through the heat exchanger. As the result, the permeation rate of aqueous tritium was found to be about three orders smaller than that of the gaseous tritium. Tritium permeation through the heat exchanger in ITER was then evaluated, and it was revealed that total tritium permeation amount based on obtained aqueous permeability was about one order less than that with the former method with the gaseous permeability and putting the permeation reduction factor as 1000. Evaluated tritium permeation amount into secondary water during 20 years was quite small, which could be considered as negligible from the safety viewpoint

Inter-utility operating data exchange concepts, standards and implementation considerations

International Nuclear Information System (INIS)

Virmani, S.; Leichner, G.H.

1991-01-01

Operating a modern interconnected electric utility in a secure and reliable manner requires a knowledge of the state of critical elements of the outside or external network. As noted in reference 1: In this paper, the authors focus on considerations in the implementation of communication processors which can be used as front ends to an EMS in order to accomplish data exchange in a multiple EMS vendor, multiple computer environment. Before discussing the implementation aspects, the paper also discusses the basic data exchange concepts in terms of the Open System Interconnection (OSI) seven layer model and the standards that are in existence or are emerging for inter-utility data exchange

Prior-to-Secondary School Course Classification System: School Codes for the Exchange of Data (SCED). NFES 2011-801

Science.gov (United States)

National Forum on Education Statistics, 2011

2011-01-01

In this handbook, "Prior-to-Secondary School Course Classification System: School Codes for the Exchange of Data" (SCED), the National Center for Education Statistics (NCES) and the National Forum on Education Statistics have extended the existing secondary course classification system with codes and descriptions for courses offered at…

The visit-data warehouse: enabling novel secondary use of health information exchange data.

Science.gov (United States)

Fleischman, William; Lowry, Tina; Shapiro, Jason

2014-01-01

Health Information Exchange (HIE) efforts face challenges with data quality and performance, and this becomes especially problematic when data is leveraged for uses beyond primary clinical use. We describe a secondary data infrastructure focusing on patient-encounter, nonclinical data that was built on top of a functioning HIE platform to support novel secondary data uses and prevent potentially negative impacts these uses might have otherwise had on HIE system performance. HIE efforts have generally formed for the primary clinical use of individual clinical providers searching for data on individual patients under their care, but many secondary uses have been proposed and are being piloted to support care management, quality improvement, and public health. This infrastructure review describes a module built into the Healthix HIE. Healthix, based in the New York metropolitan region, comprises 107 participating organizations with 29,946 acute-care beds in 383 facilities, and includes more than 9.2 million unique patients. The primary infrastructure is based on the InterSystems proprietary Caché data model distributed across servers in multiple locations, and uses a master patient index to link individual patients' records across multiple sites. We built a parallel platform, the "visit data warehouse," of patient encounter data (demographics, date, time, and type of visit) using a relational database model to allow accessibility using standard database tools and flexibility for developing secondary data use cases. These four secondary use cases include the following: (1) tracking encounter-based metrics in a newly established geriatric emergency department (ED), (2) creating a dashboard to provide a visual display as well as a tabular output of near-real-time de-identified encounter data from the data warehouse, (3) tracking frequent ED users as part of a regional-approach to case management intervention, and (4) improving an existing quality improvement program

Stability check source measurements with a secondary standard dosimeter in SSDL-Pakistan

International Nuclear Information System (INIS)

Salman, S.; Mahmoud, K.; Orfi, S.D.

1988-01-01

The stability check source is an integral part of a Secondary Standard Dosimetry System. The purpose of the stability check source is to confirm that the overall response of the dosimeter has not changed significantly since the instrument was calibrated. In case any change in the sensitivity of the ionization chamber or measuring assembly occurs the same is reflected in the reference check source measurements. Stability check source measurements are taken in a Primary Standard Dosimetry Laboratory (PSDL) at the time of calibration of secondary standard dosimeter and mean time (in seconds) to the reference setting of 50 scale divisions with ambient conditions of air at 20 deg. C, 101.3 kPa and 50% RH is quoted in a calibration certificate. This quoted stability check source time figure is the basis for future confirmation of overall response of the secondary standard dosimeter system. This note presents the results of stability check source measurements carried out in SSDL Pakistan over a period of five years

WaterML, an Information Standard for the Exchange of in-situ hydrological observations

Science.gov (United States)

Valentine, D.; Taylor, P.; Zaslavsky, I.

2012-04-01

The WaterML 2.0 Standards Working Group (SWG), working within the Open Geospatial Consortium (OGC) and in cooperation with the joint OGC-World Meteorological Organization (WMO) Hydrology Domain Working Group (HDWG), has developed an open standard for the exchange of water observation data; WaterML 2.0. The focus of the standard is time-series data, commonly generated from in-situ style monitoring. This is high value data for hydrological applications such as flood forecasting, environmental reporting and supporting hydrological infrastructure (e.g. dams, supply systems), which is commonly exchanged, but a lack of standards inhibits efficient reuse and automation. The process of developing WaterML required doing a harmonization analysis of existing standards to identify overlapping concepts and come to agreement on a harmonized definition. Generally the formats captured similar requirements, all with subtle differences, such as how time-series point metadata was handled. The in-progress standard WaterML 2.0 incorporates the semantics of the hydrologic information: location, procedure, and observations, and is implemented as an application schema of the Geography Markup Language version 3.2.1, making use of the OGC Observations & Measurements standards. WaterML2.0 is designed as an extensible schema to allow encoding of data to be used in a variety of exchange scenarios. Example areas of usage are: exchange of data for operational hydrological monitoring programs; supporting operation of infrastructure (e.g. dams, supply systems); cross-border exchange of observational data; release of data for public dissemination; enhancing disaster management through data exchange; and exchange in support of national reporting The first phase of WaterML2.0 focused on structural definitions allowing for the transfer of time-series, with less work on harmonization of vocabulary items such as quality codes. Vocabularies from various organizations tend to be specific and take time to

Geo3DML: A standard-based exchange format for 3D geological models

Science.gov (United States)

Wang, Zhangang; Qu, Honggang; Wu, Zixing; Wang, Xianghong

2018-01-01

A geological model (geomodel) in three-dimensional (3D) space is a digital representation of the Earth's subsurface, recognized by geologists and stored in resultant geological data (geodata). The increasing demand for data management and interoperable applications of geomodelscan be addressed by developing standard-based exchange formats for the representation of not only a single geological object, but also holistic geomodels. However, current standards such as GeoSciML cannot incorporate all the geomodel-related information. This paper presents Geo3DML for the exchange of 3D geomodels based on the existing Open Geospatial Consortium (OGC) standards. Geo3DML is based on a unified and formal representation of structural models, attribute models and hierarchical structures of interpreted resultant geodata in different dimensional views, including drills, cross-sections/geomaps and 3D models, which is compatible with the conceptual model of GeoSciML. Geo3DML aims to encode all geomodel-related information integrally in one framework, including the semantic and geometric information of geoobjects and their relationships, as well as visual information. At present, Geo3DML and some supporting tools have been released as a data-exchange standard by the China Geological Survey (CGS).

Secondary standard dosimetry laboratory at the Boris Kidric Institute

International Nuclear Information System (INIS)

Kovacevic, M.; Velickovic, D.; Vukcevic, M.

1989-01-01

Essential data about Secondary Standard Dosimetry Laboratory at the Boris Kidric Institute are stated in this paper. The description of the laboratory is given and the possibilities of X, gamma and neutron dose measurements, as well as the basic equipment (author)

Secondary Aluminum Production: National Emission Standards for Hazardous Air Pollutants

Science.gov (United States)

National emission standards for hazardous air pollutants (NESHAP) for new and existing sources at secondary aluminum production facilities. Includes rule history, summary, federal register citations and implementation information.

Models of information exchange between radio interfaces of Wi-Fi group of standards

Science.gov (United States)

Litvinskaya, O. S.

2018-05-01

This paper offers models of information exchange between radio interfaces of the Wi-Fi group of standards by the example of a real facility management system for the oil and gas industry. Interaction between the MU-MIMO and MIMO technologies is analyzed. An optimal variant of information exchange is proposed.

Secondary electron images obtained with a standard photoelectron emission microscope set-up

International Nuclear Information System (INIS)

Benka, Oswald; Zeppenfeld, Peter

2005-01-01

The first results of secondary electron images excited by 3-4.3 keV electrons are presented. The images are obtained with a standard FOCUS-PEEM set-up equipped with an imaging energy filter (IEF). The electron gun was mounted on a standard PEEM entrance flange at an angle of 25 deg. with respect to the sample surface. A low extraction voltage of 500 V was used to minimize the deflection of the electron beam by the PEEM extraction electrode. The secondary electron images are compared to photoelectron images excited by a standard 4.9 eV UV lamp. In the case of a Cu pattern on a Si substrate it is found that the lateral resolution without the IEF is about the same for electron and photon excitation but that the relative electron emission intensities are very different. The use of the IEF reduces the lateral resolution. Images for secondary electron energies between eV 1 and eV 2 were obtained by setting the IEF to -V 1 and -V 2 ∼-(V 1 +5V) potentials and taking the difference of both images. Images up to 100 eV electron energies were recorded. The material contrast obtained in these difference images is discussed in terms of a secondary electron and photoelectron emission model and secondary electron energy spectra measured with a LEED-Auger spectrometer

Experiments probing the influence of air exchange rates on secondary organic aerosols derived from indoor chemistry

DEFF Research Database (Denmark)

Weschler, Charles J.; Shields, H.C.

2003-01-01

Reactions between ozone and terpenes have been shown to increase the concentrations of submicron particles in indoor settings. The present study was designed to examine the influence of air exchange rates on the concentrations of these secondary organic aerosols as well as on the evolution...

Experiments probing the influence of air exchange rates on secondary organic aerosols derived from indoor chemistry

DEFF Research Database (Denmark)

Weschler, Charles J.; Shields, H.C.

2003-01-01

Reactions between ozone and terpenes have been shown to increase the concentrations of submicron particles in indoor settings. The present study was designed to examine the influence of air exchange rates on the concentrations of these secondary organic aerosols as well as on the evolution of the...

Automatic exchange of information: towards a new global standard of tax transparency

OpenAIRE

Miguel Eduardo Pecho Trigueros

2014-01-01

Tax authorities are increasingly relying on mutual cooperation with their foreign peers to enforce more effectively their internal tax laws. After the banking scandals of 2008 and the subsequent global financial crisis, the Global Forum on Transparency and Exchange of Information for TaxPurposes has proposed the exchange of information upon request as the fiscal transparency standard. However, some measures adopted by the European Union, previous initiatives from the Organization for Economic...

Patient Protection and Affordable Care Act; exchange and insurance market standards for 2015 and beyond. Final rule.

Science.gov (United States)

2014-05-27

This final rule addresses various requirements applicable to health insurance issuers, Affordable Insurance Exchanges (``Exchanges''), Navigators, non-Navigator assistance personnel, and other entities under the Patient Protection and Affordable Care Act and the Health Care and Education Reconciliation Act of 2010 (collectively referred to as the Affordable Care Act). Specifically, the rule establishes standards related to product discontinuation and renewal, quality reporting, non-discrimination standards, minimum certification standards and responsibilities of qualified health plan (QHP) issuers, the Small Business Health Options Program, and enforcement remedies in Federally-facilitated Exchanges. It also finalizes: A modification of HHS's allocation of reinsurance collections if those collections do not meet our projections; certain changes to allowable administrative expenses in the risk corridors calculation; modifications to the way we calculate the annual limit on cost sharing so that we round this parameter down to the nearest $50 increment; an approach to index the required contribution used to determine eligibility for an exemption from the shared responsibility payment under section 5000A of the Internal Revenue Code; grounds for imposing civil money penalties on persons who provide false or fraudulent information to the Exchange and on persons who improperly use or disclose information; updated standards for the consumer assistance programs; standards related to the opt-out provisions for self-funded, non-Federal governmental plans and related to the individual market provisions under the Health Insurance Portability and Accountability Act of 1996 including excepted benefits; standards regarding how enrollees may request access to non-formulary drugs under exigent circumstances; amendments to Exchange appeals standards and coverage enrollment and termination standards; and time-limited adjustments to the standards relating to the medical loss ratio

77 FR 16987 - National Emission Standards for Hazardous Air Pollutants: Secondary Aluminum Production

Science.gov (United States)

2012-03-23

... National Emission Standards for Hazardous Air Pollutants: Secondary Aluminum Production AGENCY... for secondary aluminum production (77 FR 8576). The EPA is extending the deadline for written comments... from the Aluminum Association. The Aluminum Association has requested the extension in order to allow...

Effect of plasma exchange on in-hospital mortality in patients with pulmonary hemorrhage secondary to antineutrophil cytoplasmic antibody-associated vasculitis: A propensity-matched analysis using a nationwide administrative database.

Science.gov (United States)

Uechi, Eishi; Okada, Masato; Fushimi, Kiyohide

2018-01-01

Secondary pulmonary hemorrhage increases the risk of mortality in patients with antineutrophil cytoplasmic antibody-associated vasculitis (AAV); plasma exchange therapy may improve outcomes in these patients. We conducted a retrospective cohort study to investigate the effect of plasma exchange therapy on short-term prognoses in patients with pulmonary hemorrhage secondary to AAV. This study utilized the Diagnosis Procedure Combination database, which is a nationwide inpatient database in Japan. We checked the abstract data and medical actions and identified the patients with pulmonary hemorrhage secondary to AAV who required proactive treatment between 2009 and 2014. To compare the in-hospital mortality, we performed propensity score matching between the plasma exchange and non-plasma exchange groups at a ratio of 1:1. Of the 52,932 patients with AAV, 940 developed pulmonary hemorrhage as a complication. A total of 249 patients from 194 hospitals were eligible for the study. Propensity score matching at a ratio of 1:1 was performed, and 59 pairs were formed (plasma exchange group, n = 59; non-plasma exchange group, n = 59). A statistically significant difference was found in the all-cause in-hospital mortality between the plasma exchange and non-plasma exchange groups (35.6% vs. 54.2%; p = 0041; risk difference, -18.6; 95% confidence interval (CI), -35.4% to -0.67%). Thus, plasma exchange therapy was associated with improved in-hospital mortality in patients with pulmonary hemorrhage secondary to AAV.

Patient Protection and Affordable Care Act; Exchange functions: standards for Navigators and non-Navigator assistance personnel; consumer assistance tools and programs of an Exchange and certified application counselors. Final rule.

Science.gov (United States)

2013-07-17

This final rule addresses various requirements applicable to Navigators and non-Navigator assistance personnel in Federally-facilitated Exchanges, including State Partnership Exchanges, and to non-Navigator assistance personnel in State Exchanges that are funded through federal Exchange Establishment grants. It finalizes the requirement that Exchanges must have a certified application counselor program. It creates conflict-of-interest, training and certification, and meaningful access standards; clarifies that any licensing, certification, or other standards prescribed by a state or Exchange must not prevent application of the provisions of title I of the Affordable Care Act; adds entities with relationships to issuers of stop loss insurance to the list of entities that are ineligible to become Navigators; and clarifies that the same ineligibility criteria that apply to Navigators apply to certain non-Navigator assistance personnel. The final rule also directs that each Exchange designate organizations which will then certify their staff members and volunteers to be application counselors that assist consumers and facilitate enrollment in qualified health plans and insurance affordability programs, and provides standards for that designation.

Secondary coolant purification system

International Nuclear Information System (INIS)

Stiteler, F.Z.; Donohue, J.P.

1978-01-01

The present invention combines the attributes of volatile chemical addition, continuous blowdown, and full flow condensate demineralization. During normal plant operation (defined as no primary to secondary leakage) condensate from the condenser is pumped through a full flow condensate demineralizer system by the condensate pumps. Volatile chemical additions are made. Dissolved and suspended solids are removed in the condensate polishers by ion exchange and/or filtration. At the same time a continuous blowdown of approximately 1 percent of the main steaming rate of the steam generators is maintained. Radiation detectors monitor the secondary coolant. If these monitors indicate no primary to secondary leakage, the blowdown is cooled and returned directly to the condensate pump discharge. If one of the radiation monitors should indicate a primary to secondary leak, when the temperature of the effluent exiting from the blowdown heat exchanger is compatible with the resin specifications of the ion exchangers, the bypass valve causes the blowdown flow to pass through the blowdown ion exchangers

Social network-related risk factors for bloodborne virus infections among injection drug users receiving syringes through secondary exchange.

Science.gov (United States)

De, Prithwish; Cox, Joseph; Boivin, Jean-François; Platt, Robert W; Jolly, Ann M

2008-01-01

Secondary syringe exchange (SSE) refers to the exchange of sterile syringes between injection drug users (IDUs). To date there has been limited examination of SSE in relation to the social networks of IDUs. This study aimed to identify characteristics of drug injecting networks associated with the receipt of syringes through SSE. Active IDUs were recruited from syringe exchange and methadone treatment programs in Montreal, Canada, between April 2004 and January 2005. Information on each participant and on their drug-injecting networks was elicited using a structured, interviewer-administered questionnaire. Subjects' network characteristics were examined in relation to SSE using regression models with generalized estimating equations. Of 218 participants, 126 were SSE recipients with 186 IDUs in their injecting networks. The 92 non-recipients reported 188 network IDUs. Networks of SSE recipients and non-recipients were similar with regard to network size and demographics of network members. In multivariate analyses adjusted for age and gender, SSE recipients were more likely than non-recipients to self-report being HIV-positive (OR=3.56 [1.54-8.23]); require or provide help with injecting (OR=3.74 [2.01-6.95]); have a social network member who is a sexual partner (OR=1.90 [1.11-3.24]), who currently attends a syringe exchange or methadone program (OR=2.33 [1.16-4.70]), injects daily (OR=1.77 [1.11-2.84]), and shares syringes with the subject (OR=2.24 [1.13-4.46]). SSE is associated with several injection-related risk factors that could be used to help focus public health interventions for risk reduction. Since SSE offers an opportunity for the dissemination of important prevention messages, SSE-based networks should be used to improve public health interventions. This approach can optimize the benefits of SSE while minimizing the potential risks associated with the practice of secondary exchange.

SEVA Linkers: A Versatile and Automatable DNA Backbone Exchange Standard for Synthetic Biology

DEFF Research Database (Denmark)

Kim, Se Hyeuk; Cavaleiro, Mafalda; Rennig, Maja

2016-01-01

flexibility, and different researchers prefer and master different molecular technologies. Here, we describe a new, highly versatile and automatable standard “SEVA linkers” for vector exchange. SEVA linkers enable backbone swapping with 20 combinations of classical enzymatic restriction/ligation, Gibson...

Applying Standards for Leaders to the Selection of Secondary School Principals

Science.gov (United States)

Wildy, Helen; Pepper, Coral; Guanzhong, Luo

2011-01-01

Purpose: The purpose of this paper is to report innovative research aimed at ascertaining whether standards for school leaders could be applied to the process of selecting senior secondary school principals for appointment. Specifically, psychometrically robust measures of performance are sought that would sufficiently differentiate performance to…

Technology Development Roadmap for the Advanced High Temperature Reactor Secondary Heat Exchanger

Energy Technology Data Exchange (ETDEWEB)

P. Sabharwall; M. McCllar; A. Siahpush; D. Clark; M. Patterson; J. Collins

2012-09-01

This Technology Development Roadmap (TDRM) presents the path forward for deploying large-scale molten salt secondary heat exchangers (MS-SHX) and recognizing the benefits of using molten salt as the heat transport medium for advanced high temperature reactors (AHTR). This TDRM will aid in the development and selection of the required heat exchanger for: power production (the first anticipated process heat application), hydrogen production, steam methane reforming, methanol to gasoline production, or ammonia production. This TDRM (a) establishes the current state of molten salt SHX technology readiness, (b) defines a path forward that systematically and effectively tests this technology to overcome areas of uncertainty, (c) demonstrates the achievement of an appropriate level of maturity prior to construction and plant operation, and (d) identifies issues and prioritizes future work for maturing the state of SHX technology. This study discusses the results of a preliminary design analysis of the SHX and explains the evaluation and selection methodology. An important engineering challenge will be to prevent the molten salt from freezing during normal and off-normal operations because of its high melting temperature (390°C for KF ZrF4). The efficient transfer of energy for industrial applications depends on the ability to incorporate cost-effective heat exchangers between the nuclear heat transport system and industrial process heat transport system. The need for efficiency, compactness, and safety challenge the capabilities of existing heat exchanger technology. The description of potential heat exchanger configurations or designs (such as printed circuit, spiral or helical coiled, ceramic, plate and fin, and plate type) were covered in an earlier report (Sabharwall et al. 2011). Significant future work, much of which is suggested in this report, is needed before the benefits and full potential of the AHTR can be realized. The execution of this TDRM will focuses

Optimization of shell-and-tube heat exchangers conforming to TEMA standards with designs motivated by constructal theory

International Nuclear Information System (INIS)

Yang, Jie; Fan, Aiwu; Liu, Wei; Jacobi, Anthony M.

2014-01-01

Highlights: • A design method of heat exchangers motivated by constructal theory is proposed. • A genetic algorithm is applied and the TEMA standards are rigorously followed. • Three cases are studied to illustrate the advantage of the proposed design method. • The design method will reduce the total cost compared to two other methods. - Abstract: A modified optimization design approach motivated by constructal theory is proposed for shell-and-tube heat exchangers in the present paper. In this method, a shell-and-tube heat exchanger is divided into several in-series heat exchangers. The Tubular Exchanger Manufacturers Association (TEMA) standards are rigorously followed for all design parameters. The total cost of the whole shell-and-tube heat exchanger is set as the objective function, including the investment cost for initial manufacture and the operational cost involving the power consumption to overcome the frictional pressure loss. A genetic algorithm is applied to minimize the cost function by adjusting parameters such as the tube and shell diameters, tube length and tube arrangement. Three cases are studied which indicate that the modified design approach can significantly reduce the total cost compared to the original design method and traditional genetic algorithm design method

Developing an Implementation Guideline to International Standard School for Schools under Secondary Educational Service Area Office 25

Directory of Open Access Journals (Sweden)

Worawut Poltree

2017-09-01

Full Text Available The objectives of developing an implementation guideline to international standard school for schools under secondary educational service area office 25 were ; 1 to study present and problem an implementation guideline to international standard school for schools under secondary educational service area office 25 and 2 to develop an implementation guideline to international standard school for schools under secondary educational service area office 25. There were 68 samples ; administrators, deputy administrators, head of quality management systems, and academic teachers by purposive sampling. The tools used to collect the data were the five level scale questionnaire and structured interviews. Data were analyzed using mean, standard deviation, and descriptive analysis. The researcher set the research by 2 phase. The first phase educated present and problem an implementation guideline to international standard school for schools under secondary educational service area office 25. The research was assessed feasibility of developing an implementation guideline to international standard school for schools under secondary educational service area office 25 by 5 experts. The research results were: 1. The present and problem an implementation guideline to international standard school for schools under secondary educational service area office 25 found that the overall present were at the high level and each one was at the high level. The overall problem were at the low and each one was at the moderate 2 aspects ; The leadership and the focus on personnel. Then it was at the low level. 2. Developing an implementation guideline to international standard school for schools under secondary educational service area office 25 found that 1 the leadership had set with the vision, values, performance of the school’s senior leadership, including good governance of the school, implementation of the ethics law, and responsibility for the community, 2 strategic

Development of a Secondary Neutron Fluence Standard at GELINA

International Nuclear Information System (INIS)

Heyse, Jan; Eykens, Roger; Moens, Andre; Plompen, Arjan J.M.; Schillebeeckx, Peter; Wynants, Ruud; Anastasiou, Maria

2013-06-01

The MetroFission project, a Joint Research Project within the European Metrology Research Program, aims at addressing a number of metrological problems involved in the design of proposed Generation IV nuclear reactors. One of the objectives of this multidisciplinary project is the improvement of neutron cross section measurement techniques in order to arrive at uncertainties as required for the design and safety assessment of new generation power plants and fuel cycles. This objective is in line with the 'Uncertainty and target accuracy assessment for innovative systems using recent covariance data evaluations' published by a working party of the OECD Nuclear Energy Agency in 2008. These requests are often very challenging, being at or beyond the state-of-the-art in neutron measurements, which is set by self-normalizing methods and the neutron data standards used at laboratories where the data are measured. A secondary neutron fluence standard has been developed and calibrated at the neutron time-of-flight facility GELINA of the JRC's Institute for Reference Materials and Measurements (IRMM). It consists of a flux monitor, a reference ionization chamber containing a 10 B layer and a 235 U layer, and a parallel plate ionization chamber with 8 well characterized 235 U deposits. These devices are used to determine the neutron fluence, based on the well-known neutron induced fission reaction on 235 U. All deposits have been prepared and characterized at the IRMM target preparation lab. The secondary fluence standard at the GELINA facility can be used for reliable determination of the efficiency of fluence measurement devices used in neutron data measurements at IRMM and elsewhere. It is an essential tool to reliably calibrate fluence normalization devices used in neutron time-of-flight cross section measurements. (authors)

40 CFR Appendix I to Part 50 - Interpretation of the 8-Hour Primary and Secondary National Ambient Air Quality Standards for Ozone

Science.gov (United States)

2010-07-01

... Secondary National Ambient Air Quality Standards for Ozone 1. General. This appendix explains the data.... Primary and Secondary Ambient Air Quality Standards for Ozone. 2.1 Data Reporting and Handling Conventions... and Secondary National Ambient Air Quality Standards for Ozone I Appendix I to Part 50 Protection of...

Role of secondary standard dosimetry laboratory in radiation protection program

International Nuclear Information System (INIS)

Rahman, Sohaila; Ali, Noriah Mohd.

2008-01-01

Full text: The radiation dosimetry program is an important element of operational radiation protection. Dosimetry data enable workers and radiation protection professionals to evaluate and control work practices to eliminate unnecessary exposure to ionizing radiation. The usefulness of the data produced however depends on its quality and traceability. The emphasis of the global dosimetry program is focused through the IAEA/WHO network of secondary standard dosimetry laboratories (SSDLs), which aims for the determination of SI quantities through proper traceable calibration of radiation protection equipment. The responsibility of SSDL-NUCLEAR MALAYSIA to guarantee a reliable dosimetry service, which is traceable to international standards, is elucidated. It acts as the basis for harmonized occupational radiation monitoring in Malaysia.

Application of the ICRP recommendations to revised secondary radiation protection standards

International Nuclear Information System (INIS)

Kennedy, W.E. Jr.; Corley, J.P.

1988-01-01

In 1977, the International Commission on Radiological Protection (ICRP) issued Publication No. 26 containing its recommendations for major changes in the conceptual basis for radiation protection. The new recommendations consider total risk (to the whole body) instead of controlling (critical-organ) risk. Subsequent publications and explanatory statements most useful for providing clarification of the intent of the new recommendations have not resolved practical problems encountered in attempting to apply them to either occupational or public exposures. Some of the problems that still exist in applying these recommendations for estimating doses to members of the public include the following: allowance for age differences within an exposed population group, definition of 50-y dose versus lifetime (70-y) dose, definition of negligible risk levels for individual and collective doses, and derivation of appropriate concentration guidelines. The United States is in the process of adopting the revised recommendations of the ICRP. In addition to adopting versions of the primary radiation protection standards, both the U.S. Nuclear Regulatory Commission and the U.S. Department of Energy have developed draft secondary standards that are similar to the Derived Air Concentration values given by the ICRP. This paper presents a brief history of the development of these revised secondary standards, discusses their technical bases, provides a comparison of them, and discusses their limitations and potential misapplication

The strategic use of standardized information exchange technology in a university health system.

Science.gov (United States)

Cheng, Po-Hsun; Chen, Heng-Shuen; Lai, Feipei; Lai, Jin-Shin

2010-04-01

This article illustrates a Web-based health information system that is comprised of specific information exchange standards related to health information for healthcare services in National Taiwan University Health System. Through multidisciplinary teamwork, medical and informatics experts collaborated and studied on system scope definition, standard selection challenges, system implementation barriers, system management outcomes, and further expandability of other systems. After user requirement analysis and prototyping, from 2005 to 2008, an online clinical decision support system with multiple functions of reminding and information push was implemented. It was to replace its original legacy systems and serve among the main hospital and three branches of 180-200 clinics and 7,500-8,000 patient visits per day. To evaluate the effectiveness of this system, user surveys were performed, which revealed that the average score of user satisfaction increased from 2.80 to 3.18 on a 4-point scale. Among the items, especially e-learning for training service, courtesy communications for system requests, and courtesy communications for system operations showed statistically significant improvement. From this study, the authors concluded that standardized information exchange technologies can be used to create a brand new enterprise value and steadily obtain more competitive advantages for a prestige healthcare system.

Improving ultrasound for appendicitis through standardized reporting of secondary signs.

Science.gov (United States)

Partain, Kristin N; Patel, Adarsh U; Travers, Curtis; Short, Heather L; Braithwaite, Kiery; Loewen, Jonathan; Heiss, Kurt F; Raval, Mehul V

2017-08-01

Our aim was to implement a standardized US report that included secondary signs of appendicitis (SS) to facilitate accurate diagnosis of appendicitis and decrease the use of computed tomography (CT) and admissions for observation. A multidisciplinary team implemented a quality improvement (QI) intervention in the form of a standardized US report and provided stakeholders with monthly feedback. Outcomes including report compliance, CT use, and observation admissions were compared pretemplate and posttemplate. We identified 387 patients in the pretemplate period and 483 patients in the posttemplate period. In the posttemplate period, the reporting of SS increased from 5.4% to 79.5% (pappendicitis also improved in the posttemplate period. A focused QI initiative led to high compliance rates of utilizing the standardized US report and resulted in lower CT use and fewer admissions for observation. Study of a Diagnostic Test Level of Evidence: 1. Copyright © 2017 Elsevier Inc. All rights reserved.

Geothermal heat exchanger with coaxial flow of fluids

Directory of Open Access Journals (Sweden)

Pejić Dragan M.

2005-01-01

Full Text Available The paper deals with a heat exchanger with coaxial flow. Two coaxial pipes of the secondary part were placed directly into a geothermal boring in such a way that geothermal water flows around the outer pipe. Starting from the energy balance of the exchanger formed in this way and the assumption of a study-state operating regime, a mathematical model was formulated. On the basis of the model, the secondary circle output temperature was determined as a function of the exchanger geometry, the coefficient of heat passing through the heat exchange areas, the average mass isobaric specific heats of fluid and mass flows. The input temperature of the exchanger secondary circle and the temperature of the geothermal water at the exit of the boring were taken as known values. Also, an analysis of changes in certain factors influencing the secondary water temperature was carried out. The parameters (flow temperature of the deep boring B-4 in Sijarinska Spa, Serbia were used. The theoretical results obtained indicate the great potential of this boring and the possible application of such an exchanger.

CLAIM (CLinical Accounting InforMation)--an XML-based data exchange standard for connecting electronic medical record systems to patient accounting systems.

Science.gov (United States)

Guo, Jinqiu; Takada, Akira; Tanaka, Koji; Sato, Junzo; Suzuki, Muneou; Takahashi, Kiwamu; Daimon, Hiroyuki; Suzuki, Toshiaki; Nakashima, Yusei; Araki, Kenji; Yoshihara, Hiroyuki

2005-08-01

With the evolving and diverse electronic medical record (EMR) systems, there appears to be an ever greater need to link EMR systems and patient accounting systems with a standardized data exchange format. To this end, the CLinical Accounting InforMation (CLAIM) data exchange standard was developed. CLAIM is subordinate to the Medical Markup Language (MML) standard, which allows the exchange of medical data among different medical institutions. CLAIM uses eXtensible Markup Language (XML) as a meta-language. The current version, 2.1, inherited the basic structure of MML 2.x and contains two modules including information related to registration, appointment, procedure and charging. CLAIM 2.1 was implemented successfully in Japan in 2001. Consequently, it was confirmed that CLAIM could be used as an effective data exchange format between EMR systems and patient accounting systems.

Characterization and qualification of diclofenac sodium as a secondary standard - doi: 10.4025/actascitechnol.v34i1.11654

Directory of Open Access Journals (Sweden)

Paulo Roberto Stoef

2011-11-01

Full Text Available This paper aimed to characterize and qualify a secondary standard of diclofenac sodium as a reference standard in the quality control of medicines. The identity of the candidate was confirmed through infrared spectroscopy and the content (99.63% determined by high performance liquid chromatography (HPLC by comparing with the compendial primary standard. The quality of the secondary standard was also supported by redox titration in non-aqueous media, related substances and UV spectrum by HPLC. 

Dynamic Group Diffie-Hellman Key Exchange under standard assumptions

International Nuclear Information System (INIS)

Bresson, Emmanuel; Chevassut, Olivier; Pointcheval, David

2002-01-01

Authenticated Diffie-Hellman key exchange allows two principals communicating over a public network, and each holding public-private keys, to agree on a shared secret value. In this paper we study the natural extension of this cryptographic problem to a group of principals. We begin from existing formal security models and refine them to incorporate major missing details (e.g., strong-corruption and concurrent sessions). Within this model we define the execution of a protocol for authenticated dynamic group Diffie-Hellman and show that it is provably secure under the decisional Diffie-Hellman assumption. Our security result holds in the standard model and thus provides better security guarantees than previously published results in the random oracle model

Measurements of secondary emissions from plasma arc and laser cutting in standard experiments

International Nuclear Information System (INIS)

Pilot, G.; Noel, J.P.; Leautier, R.; Steiner, H.; Tarroni, G.; Waldie, B.

1992-01-01

As part of an inter-facility comparison of secondary emissions from plasma arc and laser-cutting techniques, standard cutting tests have been done by plasma arc underwater and in air, and by laser beam in air. The same team was commissioned to measure the secondary emissions (solid and gaseous) in each contractor's facility with the same measuring rig. 20 mm and 40 mm thick, grade 304 stainless-steel plates were cut by plasma-torch in three different facilities: Heriot Watt University of Edinburgh, Institut fuer Werkstoffkunde of Universitaet Hannover and CEA/CEN Cadarache. 10 mm and in some cases 20 mm thick, grade 304, stainless-steel plates were cut by laser beam in five different facilities: CEA-CEN Fontenay, CEA-CEN Saclay, Institut fuer Werkstoffkunde of Universitaet Hannover and ENEA/Frascati. The results obtained in the standard experiments are rather similar, and the differences that appear can be explained by the various scales of the involved facilities (semi-industrial and laboratory) and by some particularities in the cutting parameters (an additional secondary gas flow of oxygen in plasma cutting at Universitaet Hannover, for example)

Measurements of secondary emissions from plasma arc and laser cutting in standard experiments

International Nuclear Information System (INIS)

Pilot, G.; Noel, M.; Leautier, R.; Steiner, H.; Tarroni, G.; Waldie, B.

1990-01-01

As part of an inter-facility comparison of secondary emissions from plasma-arc and laser cutting techniques, standard cutting tests have been done by plasma arc underwater and in air and laser beam in air. The same team, CEA/DPT/SPIN, was commissioned to measure the secondary emissions (solid and gaseous) in each contractor's facility with the same measuring rig. 20 mm and 40 mm thick grade 304 stainless steel plates were cut by plasma-torch in three different facilities: Heriot Watt University of Edinburgh, Institute fuer Werkstoffkunde of Hannover and CEA/CEN Cadarache. 10 mm and sometimes 20 mm thick grade 304 stainless steel plates were cut by laser beam in four different facilities: CEA/CEN Fontenay, CEA/CEN Saclay, Institute fuer Werkstoffkunde of Hannover and ENEA/FRASCATI. The results obtained in the standard experiments are rather similar, the differences that appear can be explained by the various scales of the facilities (semi-industrial and laboratory scale) and by some particularity in the cutting parameters (additional secondary gas flow of oxygen in plasma cutting at Hannover for example). Some supplementary experiments show the importance of some cutting parameters. (author)

Preservice Secondary Teachers Perceptions of College-Level Mathematics Content Connections with the Common Core State Standards for Mathematics

Science.gov (United States)

Olson, Travis A.

2016-01-01

Preservice Secondary Mathematics Teachers (PSMTs) were surveyed to identify if they could connect early-secondary mathematics content (Grades 7-9) in the Common Core State Standards for Mathematics (CCSSM) with mathematics content studied in content courses for certification in secondary teacher preparation programs. Respondents were asked to…

The 1998 calibration of Australian secondary standards of exposure and absorbed dose at 60Co

International Nuclear Information System (INIS)

Huntley, R.B.; Van der Gaast, H.

1998-10-01

New calibration factors are reported for several of the ionization chambers maintained at the Australian Radiation Laboratory (ARL) and at the Australian Nuclear Science and Technology Organisation (ANSTO) as Australian secondary standards of exposure/air kerma and absorbed dose at 60 Co. These calibration factors supplement or replace the calibration factors given in earlier reports. Updated 90 Sr reference source data are given for the ARL chambers, and for two of the ANSTO chambers. These results confirm the stability of the secondary standards. A re-calibration of the ANSTO reference electrometer is reported. This was carried out using an improved method, which is fully described

Standards for Exchange and Storage of 3D Information : Challenges and Opportunities for Emergency Response

NARCIS (Netherlands)

Zlatanova, S.; Stoter, J.; Isikdag, U.

2012-01-01

3D standards have been developed throughout the years for many different purposes: visualisation (fast and realistic), data management (efficient storage), modelling (validity and topology) or data exchange (platform independence). The developers also vary from companies to international

SSDL newsletter. No. 25[Secondary Standard Dosimetry Laboratories

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-10-01

In April 1976 the IAEA and the WHO concluded a Working Arrangement concerning the establishment and operation of a network of Secondary Standard Dosimetry Laboratories, based on a relationship agreement between the two organizations of 1959. This Working Arrangement was the outcome of rather lengthy consultations on the subject which rooted in recommendations of an experts' meeting on SSDL Activities, held in Rio de Janeiro 1974, and which put the bulk of responsibility for running the network on WHO. In particular, it was agreed then that WHO would provide the secretariat for the Network and be responsible for the SSDL Advisory Group of experts, the terms of reference of which were laid down in a separate document. After about ten years of operation of the SSDL Network it was felt that revision of the Working Arrangement should be considered, taking care of the actual involvement of the two organizations in the project and providing a more fairly balanced share of responsibilities between the IAEA and WHO secretaries of the Network. The new Arrangement was drafted during 1985 and signed by the two Directors General in October/November 1985. Upon recommendation of an SSDL Advisory Group which met in November 1984 the Directors General of IAEA and WHO appointed 6 scientists as members of a standing SSDL Scientific Committee. The appointment is for a period of three years. In its terms of reference the functions of this Committee are defined as follows: to provide technical advice to the Directors General of the IAEA and WHO regarding the programme of work of the IAEA/WHO Network of Secondary Standard Dosimetry Laboratories; to assist the Network Secretariat with scientific advice and to regularly review the work undertaken by members of the SSDL Network; to make recommendations on the techniques for carrying out intercomparisons between SSDLs; to advise and make recommendations on the techniques for establishing and maintaining traceability to the Primary Standard

State insurance exchanges face challenges in offering standardized choices alongside innovative value-based insurance.

Science.gov (United States)

Corlette, Sabrina; Downs, David; Monahan, Christine H; Yondorf, Barbara

2013-02-01

Value-based insurance is a relatively new approach to health insurance in which financial barriers, such as copayments, are lowered for clinical services that are considered high value, while consumer cost sharing may be increased for services considered to be of uncertain value. Such plans are complex and do not easily fit into the simplified, consumer-friendly comparison tools that many state health insurance exchanges are formulating for use in 2014. Nevertheless some states and plans are attempting to strike the right balance between a streamlined health exchange shopping experience and innovative, albeit complex, benefit design that promotes value. For example, agencies administering exchanges in Vermont and Oregon are contemplating offering value-based insurance plans as an option in addition to a set of standardized plans. In the postreform environment, policy makers must find ways to present complex value-based insurance plans in a way that consumers and employers can more readily understand.

Guidelines for Member States concerning radiation measurement standards and Secondary Standard Dosimetry Laboratories

International Nuclear Information System (INIS)

1986-01-01

In the early nineteen-sixties an acute need developed for higher dosimetric accuracy in radiation therapy, particularly in developing countries. This need led to the establishment of a number of dosimetry laboratories around the world, specializing in the calibration of radiation therapy dosimeters. In order to co-ordinate the provision of guidance and assistance to such laboratories, the International Atomic Energy Agency (IAEA) and the World Health Organization (WHO) set up a Network of Secondary Standard Dosimetry Laboratories (SSDLs) under their joint aegis, as described in the IAEA booklet 'SSDLs: Development and Trends' (1985). This publication includes detailed criteria for the establishment of these laboratories. The present guidelines deal with the functions and status of SSDLs, in particular with the need for recognition and support by the competent national authorities. (author)

A standard format for data exchange - SFD

DEFF Research Database (Denmark)

Dindorp, Ulla; Flensted-Jensen, Mogens; Ravn, Anders P.

1996-01-01

We investigate the issues in making experimental data available for later inspection or reuse. A prototype software system - SFD - that solves the technical problems in data exchange is presented, and early user experience is discussed.......We investigate the issues in making experimental data available for later inspection or reuse. A prototype software system - SFD - that solves the technical problems in data exchange is presented, and early user experience is discussed....

Certification of materials for steam generator condensor and regeneration heat exchanger for nuclear plant

International Nuclear Information System (INIS)

Stevanovicj, M.V.; Jovashevicj, V.J.; Jovashevicj, V.D.J.; Spasicj, Zh.Lj.

1977-01-01

In the construction of a nuclear power plant almost all known materials are used. The choice depends on working conditions. In this work standard specifications of contemporary materials that take part in larger quantities in the following components of the secondary circuit of PWR-type nuclear power plant are proposed: steam generator with moisture separator, condensor and regenerative heat eXchanger

Secondary standard dosimetry laboratory Saraykoy Nuclear Research and Training Center Ankara, Turkey

International Nuclear Information System (INIS)

Okruhlica, P.

2014-01-01

Turkish Saraykoy Nuclear Research and Training Center (SANA) was founded in 2005. In 2014 the company PTW Freiburg in cooperation with VF Cerna Hora started the construction of a comprehensive national metrology laboratories of ionizing radiation 'Secondary Standard Dosimetry Laboratory' (SSDL). The laboratory will be located in the area of 'Saraykoy Nuclear Research and Training Center' in Ankara in Turkey. SSDL will be equipped with metrology departments for calibration and measurement of standard required quantities of metrology of ionizing radiation: - Neutron workplace; Gamma workplace (low-energy X-ray, gamma Standard Cs-137 and high dose rate, Co-60); - Beta workplace; - Control system of metrology laboratories and irradiation VF DARS; - Radiation monitoring system VF RMS; - Camera and security system; - Measuring instruments (ionization chambers, electrometers, monitors for environmental measurements ...) with the appropriate phantoms and other systems.

40 CFR Appendix P to Part 50 - Interpretation of the Primary and Secondary National Ambient Air Quality Standards for Ozone

Science.gov (United States)

2010-07-01

... the data handling procedures for the reported data). 2.3Comparisons with the Primary and Secondary... Secondary National Ambient Air Quality Standards for Ozone P Appendix P to Part 50 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS NATIONAL PRIMARY AND SECONDARY AMBIENT AIR QUALITY...

The IAEA/WHO network of Secondary Standard Dosimetry Laboratories. SSDL network charter

International Nuclear Information System (INIS)

1999-04-01

In 1976, the International Atomic Energy Agency (IAEA) together with the World Health Organization (WHO) established a Network of Secondary Standard Dosimetry Laboratories (SSDLs), known as the IAEA/WHO SSDL Network. This Network, through SSDLs designated by Member States, provides a direct linkage of national dosimetry standards to the international measurement system of standards traceable to the Bureau International des Poids et Mesures (BIPM), and the dissemination of S.I. quantities and units through the proper calibration of field instruments by the SSDLs. The Network has proved to be of value in improving national capabilities for instrument calibration and the awareness of better accuracy and traceability. Fifty-eight countries have nominated SSDLs for membership in the Network. Unfortunately, some of these SSDLs do not yet function as full members, perhaps because of some uncertainty as to their obligations concerning the Network. Consequently, the Scientific Committee which advises the Network Secretariat has recommended that a Charter be drawn up explaining the privileges, rights and duties of members in the Network which would strengthen their links to the international measurement system. In addition to the duties of members in the Network and the benefits that full members can receive, the Charter also describes how the Network functions and the scope of the work of the SSDLs. In producing this Charter, the advisory group has drawn heavily on the IAEA publication 'Secondary Standard Dosimetry Laboratories: Development and Trends' (1985) which summarizes the origin, development, status and prospects of the IAEA/WHO SSDL Network. The various appendices are effectively up-dates of different parts of this earlier publication, and the original drafting and reviewing bodies are given due recognition. The revisions take into account the experience the Agency has gained in coordinating the activities of the Network for more than 20 years

The IAEA/WHO network of Secondary Standard Dosimetry Laboratories. SSDL network charter

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-04-01

In 1976, the International Atomic Energy Agency (IAEA) together with the World Health Organization (WHO) established a Network of Secondary Standard Dosimetry Laboratories (SSDLs), known as the IAEA/WHO SSDL Network. This Network, through SSDLs designated by Member States, provides a direct linkage of national dosimetry standards to the international measurement system of standards traceable to the Bureau International des Poids et Mesures (BIPM), and the dissemination of S.I. quantities and units through the proper calibration of field instruments by the SSDLs. The Network has proved to be of value in improving national capabilities for instrument calibration and the awareness of better accuracy and traceability. Fifty-eight countries have nominated SSDLs for membership in the Network. Unfortunately, some of these SSDLs do not yet function as full members, perhaps because of some uncertainty as to their obligations concerning the Network. Consequently, the Scientific Committee which advises the Network Secretariat has recommended that a Charter be drawn up explaining the privileges, rights and duties of members in the Network which would strengthen their links to the international measurement system. In addition to the duties of members in the Network and the benefits that full members can receive, the Charter also describes how the Network functions and the scope of the work of the SSDLs. In producing this Charter, the advisory group has drawn heavily on the IAEA publication 'Secondary Standard Dosimetry Laboratories: Development and Trends' (1985) which summarizes the origin, development, status and prospects of the IAEA/WHO SSDL Network. The various appendices are effectively up-dates of different parts of this earlier publication, and the original drafting and reviewing bodies are given due recognition. The revisions take into account the experience the Agency has gained in coordinating the activities of the Network for more than 20 years.

78 FR 29805 - Self-Regulatory Organizations; BATS Exchange, Inc.; Notice of Filing and Immediate Effectiveness...

Science.gov (United States)

2013-05-21

... at the Exchange's primary data center and one port at the Exchange's secondary data center. With... primary data center and that no logical port fees will be assessed for redundant secondary data center... Members or non- members, as the Exchange is already providing secondary data center ports free of charge...

Heat exchange apparatus

International Nuclear Information System (INIS)

Thurston, G.C.; McDaniels, J.D.; Gertsch, P.R.

1979-01-01

The present invention relates to heat exchangers used for transferring heat from the gas cooled core of a nuclear reactor to a secondary medium during standby and emergency conditions. The construction of the heat exchanger described is such that there is a minimum of welds exposed to the reactor coolant, the parasitic heat loss during normal operation of the reactor is minimized and the welds and heat transfer tubes are easily inspectable. (UK)

Electrically switched cesium ion exchange

International Nuclear Information System (INIS)

Lilga, M.A.; Orth, R.J.; Sukamto, J.P.H.; Schwartz, D.T.; Haight, S.M.; Genders, J.D.

1997-04-01

Electrically Switched Ion Exchange (ESIX) is a separation technology being developed as an alternative to conventional ion exchange for removing radionuclides from high-level waste. The ESIX technology, which combines ion exchange and electrochemistry, is geared toward producing electroactive films that are highly selective, regenerable, and long lasting. During the process, ion uptake and elution are controlled directly by modulating the potential of an ion exchange film that has been electrochemically deposited onto a high surface area electrode. This method adds little sodium to the waste stream and minimizes the secondary wastes associated with traditional ion exchange techniques. Development of the ESIX process is well underway for cesium removal using ferrocyanides as the electroactive films. Films having selectivity for perrhenate (a pertechnetate surrogate) over nitrate also have been deposited and tested. A case study for the KE Basin on the Hanford Site was conducted based on the results of the development testing. Engineering design baseline parameters for film deposition, film regeneration, cesium loading, and cesium elution were used for developing a conceptual system. Order of magnitude cost estimates were developed to compare with conventional ion exchange. This case study demonstrated that KE Basin wastewater could be processed continuously with minimal secondary waste and reduced associated disposal costs, as well as lower capital and labor expenditures

77 FR 48491 - Regulatory New Drug Review: Solutions for Study Data Exchange Standards; Notice of Meeting...

Science.gov (United States)

2012-08-14

... input from industry, technology vendors, and other members of the public regarding the advantages and disadvantages of current and emerging open, consensus-based standards for the exchange of regulated study data... many years, it is not an extensible modern technology. Moreover, it is not supported and maintained by...

Standards, Data Exchange and Intellectual Property Rights in Systems Biology

DEFF Research Database (Denmark)

van Zimmeren, Esther; Rutz, Berthold; Minssen, Timo

2016-01-01

” of scientists. In 2015, Biotechnology Journal published a report from an expert meeting on “Synthetic Biology & Intellectual Property Rights” organized by the Danish Agency for Science, Technology and Innovation sponsored by the European Research Area Network (ERA-Net) in Synthetic Biology (ERASynBio), in which...... we provided a number of recommendations for a variety of stakeholders. The current article offers some deeper reflections about the interface between IPRs, standards and data exchange in Systems Biology resulting from an Expert Meeting funded by another ERA-Net, ERASysAPP. The meeting brought...... together experts and stakeholders (e.g. scientists, company representatives, officials from public funding organizations) in systems biology (SysBio) from different countries.  Despite the different profiles of the stakeholders at the meeting and the variety of interests, many concerns and opinions were...

Exchange effects in Relativistic Schroedinger Theory

International Nuclear Information System (INIS)

Sigg, T.; Sorg, M.

1998-01-01

The Relativistic Schroedinger Theory predicts the occurrence of exchange and overlap effects in many-particle systems. For a 2-particle system, the interaction energy of the two particles consists of two contributions: Coulomb energy and exchange energy, where the first one is revealed to be the same as in standard quantum theory. However the exchange energy is mediated by an exchange potential, contrary to the kinematical origin of the exchange term in the standard theory

Increasing of prediction reliability of calcium carbonate scale formation in heat exchanger of secondary coolant circuits of thermal and nuclear power plants

International Nuclear Information System (INIS)

Tret'yakov, O.V.; Kritskij, V.G.; Styazhkin, P.S.

1991-01-01

Calcium carbonate scale formation in the secondary circuit heat exchanger of thermal and nuclear power plants is investigated. A model of calcium-carbonate scale formation providing quite reliable prediction of process running and the possibility of its control affecting the parameters of hydrochemical regime (HCR) is developed. The results can be used when designing the automatic-control system of HCR

National BTS bronchiectasis audit 2012: is the quality standard being adhered to in adult secondary care?

Science.gov (United States)

Hill, Adam T; Routh, Chris; Welham, Sally

2014-03-01

A significant step towards improving care of patients with non-cystic fibrosis bronchiectasis was the creation of the British Thoracic Society (BTS) national guidelines and the quality standard. A BTS bronchiectasis audit was conducted between 1 October and 30 November 2012, in adult patients with bronchiectasis attending secondary care, against the BTS quality standard. Ninety-eight institutions took part, submitting a total of 3147 patient records. The audit highlighted the variable adoption of the quality standard. It will allow the host institutions to benchmark against UK figures and drive quality improvement programmes to promote the quality standard and improve patient care.

An organic profile of a pressurised water reactor secondary plant

International Nuclear Information System (INIS)

Eeden, Nestor van; Stwayi, Mandisibuntu; Gericke, Gerhard

2012-01-01

Make-up water addition to the steam/water cycle at Koeberg Nuclear Power Station usually results in a corresponding increase of the chloride concentration in the steam generator blowdown system. During plant transients, when higher than normal make-up is required to the secondary plant, the concentration of chloride occasionally exceeds the limiting value for the station chemistry performance indicator. Irrespective of this, the demineralised water make-up supply tanks, which are routinely analysed for chloride, are within all recognised acceptable standards for secondary water make-up and therefore these tanks do not initially appear to be the source of chloride contamination. Water treatment at the plant relies essentially on ion exchange, which has been proven to be very effective in removing inorganic ionic species such as chloride. Organic compounds are less effectively removed by ion exchange and may pass through the treatment system, and these organics can reside undetected in the make-up water tanks. Historically, the elevated chloride concentration following high system make-up has been attributed to chlorinated organic compounds known as trihalomethanes being present in the make-up water tanks, but no rigorous study had been undertaken. As it has been assumed that the majority of chloride in the secondary system originates from the make-up water organic impurities, it was considered important to confirm this by compiling an organic profile of the secondary plant. The use of organic additives was also taken into account in the profile. This work has confirmed the contribution from trihalomethanes and has also found that other organochlorides contribute even more significantly to the overall chloride inventory of the secondary plant. (orig.)

The Metaphysics of Economic Exchanges

Directory of Open Access Journals (Sweden)

Massin Olivier

2017-05-01

Full Text Available What are economic exchanges? The received view has it that exchanges are mutual transfers of goods motivated by inverse valuations thereof. As a corollary, the standard approach treats exchanges of services as a subspecies of exchanges of goods. We raise two objections against this standard approach. First, it is incomplete, as it fails to take into account, among other things, the offers and acceptances that lie at the core of even the simplest cases of exchanges. Second, it ultimately fails to generalize to exchanges of services, in which neither inverse preferences nor mutual transfers hold true. We propose an alternative definition of exchanges, which treats exchanges of goods as a special case of exchanges of services and which builds in offers and acceptances. According to this theory: (i The valuations motivating exchanges are propositional and convergent rather than objectual and inverse; (ii All exchanges of goods involve exchanges of services/actions, but not the reverse; (iii Offers and acceptances, together with the contractual obligations and claims they bring about, lie at the heart of all cases of exchange.

Preliminary results of statistical dynamic experiments on a heat exchanger

International Nuclear Information System (INIS)

Corran, E.R.; Cummins, J.D.

1962-10-01

The inherent noise signals present in a heat exchanger have been recorded and analysed in order to determine some of the statistical dynamic characteristics of the heat exchanger. These preliminary results show that the primary side temperature frequency response may be determined by analysing the inherent noise. The secondary side temperature frequency response and cross coupled temperature frequency responses between primary and secondary are poorly determined because of the presence of a non-stationary noise source in the secondary circuit of this heat exchanger. This may be overcome by correlating the dependent variables with an externally applied noise signal. Some preliminary experiments with an externally applied random telegraph type of signal are reported. (author)

Heat exchanger

International Nuclear Information System (INIS)

Drury, C.R.

1988-01-01

A heat exchanger having primary and secondary conduits in heat-exchanging relationship is described comprising: at least one serpentine tube having parallel sections connected by reverse bends, the serpentine tube constituting one of the conduits; a group of open-ended tubes disposed adjacent to the parallel sections, the open-ended tubes constituting the other of the conduits, and forming a continuous mass of contacting tubes extending between and surrounding the serpentine tube sections; and means securing the mass of tubes together to form a predetermined cross-section of the entirety of the mass of open-ended tubes and tube sections

Hydrogen exchange

DEFF Research Database (Denmark)

Jensen, Pernille Foged; Rand, Kasper Dyrberg

2016-01-01

Hydrogen exchange (HX) monitored by mass spectrometry (MS) is a powerful analytical method for investigation of protein conformation and dynamics. HX-MS monitors isotopic exchange of hydrogen in protein backbone amides and thus serves as a sensitive method for probing protein conformation...... and dynamics along the entire protein backbone. This chapter describes the exchange of backbone amide hydrogen which is highly quenchable as it is strongly dependent on the pH and temperature. The HX rates of backbone amide hydrogen are sensitive and very useful probes of protein conformation......, as they are distributed along the polypeptide backbone and form the fundamental hydrogen-bonding networks of basic secondary structure. The effect of pressure on HX in unstructured polypeptides (poly-dl-lysine and oxidatively unfolded ribonuclease A) and native folded proteins (lysozyme and ribonuclease A) was evaluated...

Heat exchanger

International Nuclear Information System (INIS)

Leigh, D.G.

1976-01-01

The arrangement described relates particularly to heat exchangers for use in fast reactor power plants, in which heat is extracted from the reactor core by primary liquid metal coolant and is then transferred to secondary liquid metal coolant by means of intermediate heat exchangers. One of the main requirements of such a system, if used in a pool type fast reactor, is that the pressure drop on the primary coolant side must be kept to a minimum consistent with the maintenance of a limited dynamic head in the pool vessel. The intermediate heat exchanger must also be compact enough to be accommodated in the reactor vessel, and the heat exchanger tubes must be available for inspection and the detection and plugging of leaks. If, however, the heat exchanger is located outside the reactor vessel, as in the case of a loop system reactor, a higher pressure drop on the primary coolant side is acceptable, and space restriction is less severe. An object of the arrangement described is to provide a method of heat exchange and a heat exchanger to meet these problems. A further object is to provide a method that ensures that excessive temperature variations are not imposed on welded tube joints by sudden changes in the primary coolant flow path. Full constructional details are given. (U.K.)

Recent advances in standards for collaborative Digital Anatomic Pathology

Science.gov (United States)

2011-01-01

Context Collaborative Digital Anatomic Pathology refers to the use of information technology that supports the creation and sharing or exchange of information, including data and images, during the complex workflow performed in an Anatomic Pathology department from specimen reception to report transmission and exploitation. Collaborative Digital Anatomic Pathology can only be fully achieved using medical informatics standards. The goal of the international integrating the Healthcare Enterprise (IHE) initiative is precisely specifying how medical informatics standards should be implemented to meet specific health care needs and making systems integration more efficient and less expensive. Objective To define the best use of medical informatics standards in order to share and exchange machine-readable structured reports and their evidences (including whole slide images) within hospitals and across healthcare facilities. Methods Specific working groups dedicated to Anatomy Pathology within multiple standards organizations defined standard-based data structures for Anatomic Pathology reports and images as well as informatic transactions in order to integrate Anatomic Pathology information into the electronic healthcare enterprise. Results The DICOM supplements 122 and 145 provide flexible object information definitions dedicated respectively to specimen description and Whole Slide Image acquisition, storage and display. The content profile “Anatomic Pathology Structured Report” (APSR) provides standard templates for structured reports in which textual observations may be bound to digital images or regions of interest. Anatomic Pathology observations are encoded using an international controlled vocabulary defined by the IHE Anatomic Pathology domain that is currently being mapped to SNOMED CT concepts. Conclusion Recent advances in standards for Collaborative Digital Anatomic Pathology are a unique opportunity to share or exchange Anatomic Pathology structured

Evaluation of uncertainties in X radiation metrologic chain in the Secondary Standard Dosimetry Laboratory/IRD-Brazilian CNEN

International Nuclear Information System (INIS)

Fonseca Coelho, B.C. da.

1987-01-01

The equipment to measure ionizing radiation used in medicine needs appropriate technical qualifications to comply with their purposes and regular calibrations to assure the correct evaluation of associated quantities. By legal requirements, the annual calibration of users' dosemeters is to be done in a Secondary Standard Dosimetry Laboratory (SSDL), andthe SSDL'S standard dosemeters are refered to a Primary Standard Dosimetry (PSDL), establishing a rigourous metrological network. The SSDL network. The SSDL needs to maintain, regularly, a quality control program for short and Long term stability of standard dosemeters. The purpose of the work was to determine the uncertainties associated to technical procedures of X-rays calibration at the SSDL/IRD/IRD. To evaluate the influence of the nine main parameters that can give origin to uncertainties, specific procedures and methods are established, according to international requirements and recomendations. The methods are based on the comparison of the behaviour of the users' dosemeters, with a standard dosemeter in the many measuring conditions set up for the secondary standard used as a reference. The total uncertainty obtained was 1,81% usig a conservative procedure, to protect the users and patients. When needed to transfer the calibration factor and their uncertainty, the procedure used was to determine the uncertainty under the worsst possible operating conditions of the equipment, to obtain a superestimated value. This represents an excellent result for an SDDL of IAEA Network. (autor) [pt

Essential Specification Elements for Heat Exchanger Replacement

Energy Technology Data Exchange (ETDEWEB)

Bower, L.

2015-07-01

Performance upgrade and equipment degradation are the primary impetuses for a nuclear power plant to engage in the large capital cost project of heat exchanger replacement. Along with attention to these issues, consideration of heat exchanger Codes and Standards, material improvements, thermal redesign, and configuration are essential for developing User’s Design Specifications for successful replacement projects. The User’s Design Specification is the central document in procuring ASME heat exchangers. Properly stated objectives for the heat exchanger replacement are essential for obtaining the materials, configurations and thermal designs best suited for the nuclear power plant. Additionally, the code of construction required and the applied manufacturing standard (TEMA or HEI) affects how the heat exchanger may be designed or configured to meet the replacement goals. Knowledge of how Codes and Standards affect design and configuration details will aid in writing the User’s Design Specification. Joseph Oat Corporation has designed and fabricated many replacement heat exchangers for the nuclear power industry. These heat exchangers have been constructed per ASME Section III to various Code-Years or ASME Section VIII-1 to the current Code-Year also in accordance with TEMA and HEI. These heat exchangers have been a range of like-for-like replacement to complete thermal, material and configuration redesigns. Several examples of these heat exchangers with their Code, Standard and specification implications are presented. (Author.

Heat exchanger

Science.gov (United States)

Daman, Ernest L.; McCallister, Robert A.

1979-01-01

A heat exchanger is provided having first and second fluid chambers for passing primary and secondary fluids. The chambers are spaced apart and have heat pipes extending from inside one chamber to inside the other chamber. A third chamber is provided for passing a purge fluid, and the heat pipe portion between the first and second chambers lies within the third chamber.

Quark-antiquark exchange in γ* γ* scattering

International Nuclear Information System (INIS)

Bartels, J.; Lublinsky, M.

2003-01-01

We calculate the high energy behavior of quark-antiquark exchange in γ* γ* elastic scattering by summing, to all orders, the leading double logarithmic contributions of the QCD ladder diagrams. Motivation comes from the LEP data for σ tot (γ* γ*) which indicate the need for secondary reggeon exchange. We show that, for large photon virtualities, this exchange is calculable in pQCD. This applies, in particular, to parts of the LEP kinematic region. (author)

Computer-aided process planning in prismatic shape die components based on Standard for the Exchange of Product model data

Directory of Open Access Journals (Sweden)

Awais Ahmad Khan

2015-11-01

Full Text Available Insufficient technologies made good integration between the die components in design, process planning, and manufacturing impossible in the past few years. Nowadays, the advanced technologies based on Standard for the Exchange of Product model data are making it possible. This article discusses the three main steps for achieving the complete process planning for prismatic parts of the die components. These three steps are data extraction, feature recognition, and process planning. The proposed computer-aided process planning system works as part of an integrated system to cover the process planning of any prismatic part die component. The system is built using Visual Basic with EWDraw system for visualizing the Standard for the Exchange of Product model data file. The system works successfully and can cover any type of sheet metal die components. The case study discussed in this article is taken from a large design of progressive die.

Upright heat exchanger

International Nuclear Information System (INIS)

Martoch, J.; Kugler, V.; Krizek, V.; Strmiska, F.

1988-01-01

The claimed heat exchanger is characteristic by the condensate level being maintained directly in the exchanger while preserving the so-called ''dry'' tube plate. This makes it unnecessary to build another pressure vessel into the circuit. The design of the heat exchanger allows access to both tube plates, which facilitates any repair. Another advantage is the possibility of accelerating the indication of leakage from the space of the second operating medium which is given by opening the drainage pipes of the lower bundle into the collar space and from there through to the indication pipe. The exchanger is especially suitable for deployment in the circuits of nuclear power plants where the second operating medium will be hot water of considerably lower purity than is that of the condensate. A rapid display of leakage can prevent any long-term penetration of this water into the condensate, which would result in worsening water quality in the entire secondary circuit of the nuclear power plant. (J.B.). 1 fig

Standardization of Brief Inventory of Social Support Exchange Network (BISSEN) in Japan.

Science.gov (United States)

Aiba, Miyuki; Tachikawa, Hirokazu; Fukuoka, Yoshiharu; Lebowitz, Adam; Shiratori, Yuki; Doi, Nagafumi; Matsui, Yutaka

2017-07-01

This study describes the Brief Inventory of Social Support Exchange Network (BISSEN) as a standardized brief inventory measuring various aspects of social support. We confirmed the reliability and validity for function and direction of support and standardized the BISSEN. For Sample 1, a stratified random sampling method was used to select 5200 residents in Japan. We conducted mail surveys and responses were retrieved from 2274 participants (collection rate 43.7%). Participants completed a questionnaire packet that included BISSEN, suicidal ideation, depression, support seeking, and Multidimensional Scale of Perceived Social Support (MSPSS). Sample 2 surveys for test-retest reliability were conducted on 23 residents at approximately two-week intervals. Participants were asked about gender, age, and BISSEN. First, we assessed the internal consistency, test-retest reliability, construct, convergent, and concurrent validity. McDonald's omega (.73-.92) and test-retest correlations (.78-.85) demonstrated adequate internal consistency and test-retest reliability. Depression, support seeking, and MSPSS were significantly correlated with all scores of BISSEN. The non-suicidal ideation group had significantly more support compared to the suicidal ideation group. Therefore, function and direction of support in BISSEN had sufficient reliability and validity. Next, we standardized BISSEN using Z-scores and percentile rank with respect to each 12 norm groups by age and gender. Copyright © 2017 Elsevier Ireland Ltd. All rights reserved.

Standardizing information exchange towards the end user. Present data models with two way communication over the Internet

International Nuclear Information System (INIS)

Saele, Hanne; Graabak, Ingeborg; Tangen, Grethe

2000-01-01

The two-way communication towards the end consumer is in little use so far. There are probably several reasons for this but one important reason may be the lack of standardized interfaces for the information exchange towards the end user. The lack of such standards results in substantial system investment risks for the network companies because the systems may not be developed further and maintained should the deliverer leave the market. The communication channel Internet has expanded quickly and in Norway of today (1999) 25 to 30 % of the households have an Internet connection. The use of existing infrastructure and already tried out technology for information transferrals may contribute to making two-way communication more reasonable and functional. In the report various alternatives of standardized information exchange towards the end users are evaluated. Various formats are discussed with the following demands in mind: 1) Shall be suited for all types of communication media. 2) An international standard followed by everyone. 3) Reliable information transferral and flexible. The focus is on what kind of information is being transferred and how this is organized, and not on how the information is transferred. The discussed alternatives are evaluated both regarding traditional solutions for two- way communication and the use of the Internet. The following format alternatives are discussed: EDIEL/EDIFACT, ODEL(GS2), LonWorks/Echelon, UCA, DLMS/COSEM, COBRA and DCOM. The formats represent communication at various levels but they are mentioned in the report because they are often mentioned as possible standard formats towards the end user: ODEL, DLSM/COSEM and UCA. EDIEL is not suited for this interface. The market for two-way communication systems is international and it does not seem to be practical to establish a joint Norwegian/Swedish standard. The work with establishing one standard should therefore be continued through international standardization

Introducing ADES: A New IAU Astrometry Data Exchange Standard

Science.gov (United States)

Chesley, Steven R.; Hockney, George M.; Holman, Matthew J.

2017-10-01

For several decades, small body astrometry has been exchanged, distributed and archived in the form of 80-column ASCII records. As a replacement for this obsolescent format, we have worked with a number of members of the community to develop the Astrometric Data Exchange Standard (ADES), which was formally adopted by IAU Commission 20 in August 2015 at the XXIX General Assembly in Honolulu, Hawaii.The purpose of ADES is to ensure that useful and available observational information is submitted, archived, and disseminated as needed. Availability of more complete information will allow orbit computers to process the data more correctly, leading to improved accuracy and reliability of orbital fits. In this way, it will be possible to fully exploit the improving accuracy and increasing number of both optical and radar observations. ADES overcomes several limitations of the previous format by allowing characterization of astrometric and photometric errors, adequate precision in time and angle fields, and flexibility and extensibility.To accommodate a diverse base of users, from automated surveys to hands-on follow-up observers, the ADES protocol allows for two file formats, eXtensible Markup Language (XML) and Pipe-Separated Values (PSV). Each format carries the same information and simple tools allow users to losslessly transform back and forth between XML and PSV.We have further developed and refined ADES since it was first announced in July 2015 [1]. The proposal at that time [2] has undergone several modest revisions to aid validation and avoid overloaded fields. We now have validation schema and file transformation utilities. Suitable example files, test suites, and input/output libraries in a number of modern programming languages are now available. Acknowledgements: Useful feedback during the development of ADES has been received from numerous colleagues in the community of observers and orbit specialists working on asteroids comets and planetary satellites

40 CFR 50.11 - National primary and secondary ambient air quality standards for oxides of nitrogen (with...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 2 2010-07-01 2010-07-01 false National primary and secondary ambient air quality standards for oxides of nitrogen (with nitrogen dioxide as the indicator). 50.11 Section 50.11 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS NATIONAL...

Secondary calibration laboratory for ionizing radiation laboratory accreitation program National Institute of Standards and Technology National Voluntary Laboratory Accreditation Program

Energy Technology Data Exchange (ETDEWEB)

Martin, P.R.

1993-12-31

This paper presents an overview of the procedures and requirements for accreditation under the Secondary Calibration Laboratory for Ionizing Radiation Program (SCLIR LAP). The requirements for a quality system, proficiency testing and the onsite assessment are discussed. The purpose of the accreditation program is to establish a network of secondary calibration laboratories that can provide calibrations traceable to the primary national standards.

Secondary calibration laboratory for ionizing radiation laboratory accreitation program National Institute of Standards and Technology National Voluntary Laboratory Accreditation Program

International Nuclear Information System (INIS)

Martin, P.R.

1993-01-01

This paper presents an overview of the procedures and requirements for accreditation under the Secondary Calibration Laboratory for Ionizing Radiation Program (SCLIR LAP). The requirements for a quality system, proficiency testing and the onsite assessment are discussed. The purpose of the accreditation program is to establish a network of secondary calibration laboratories that can provide calibrations traceable to the primary national standards

Preliminary conceptual design of the secondary sodium circuit-eliminated JSFR (Japan Sodium Fast Reactor) adopting a supercritical CO2 turbine system (1). Sodium/CO2 heat exchanger

International Nuclear Information System (INIS)

Kisohara, Naoyuki; Sakamoto, Yoshihiko; Kotake, Shoji

2014-09-01

Research and development of the supercritical CO 2 (S-CO 2 ) cycle turbine system is underway in various countries for further improvement of the safety and economy of sodium-cooled fast reactors. The Component Design and Balance-Of-Plant (CD and BOP) of the Generation IV International Nuclear Forum (Gen-IV) has addressed this study, and their analytical and experimental results have been discussed between the relevant countries. JAEA, who is a member of the CD and BOP, has performed a design study of an S-CO 2 gas turbine system applied to the Japan Sodium-cooled Fast Reactor (JSFR). In this study, the S-CO 2 cycle turbine system was directly connected to the primary sodium system of the JSFR to eliminate the secondary sodium circuit, aiming for further economical improvement. This is because there is no risk of sodium-water reaction in the S-CO 2 cycle turbine system of SFRs. The Na/CO 2 heat exchanger is one of the key components for the secondary sodium system eliminated SFR, and this report describes its structure and the safety in case of CO 2 leak. A Printed Circuit Heat Exchanger (PCHE), which has a greater heat transfer performance, is employed to the heat exchanger. Another advantage of the PCHE is to limit the area affected by a leak of CO 2 because of its partitioned flow path structure. A SiC/SiC ceramic composite material is used for the PCHE to prevent crack growth and to reduce thermal stress. The Na/CO 2 heat exchanger has been designed in such a way that a number of small heat transfer modules are combined in the vessel in consideration of manufacture and repair. The primary sodium pump is installed in the center of the heat exchanger vessel. CO 2 leak events in the heat exchanger have been also evaluated, and it revealed that no significant effect has arisen on the core or the primary sodium boundary. (author)

Failure of standard approximations of the exchange coupling in nanostructures

DEFF Research Database (Denmark)

Pedersen, Jesper Goor; Flindt, Christian; Mortensen, Asger

2007-01-01

We calculate the exchange coupling for a double dot system using a numerically exact technique based on finite-element methods and an expansion in two-dimensional Gaussians. Specifically, we evaluate the exchange coupling both for a quasi-one- and a two-dimensional system, also including an appli...

Constructing Assessment Model of Primary and Secondary Educational Quality with Talent Quality as the Core Standard

Science.gov (United States)

Chen, Benyou

2014-01-01

Quality is the core of education and it is important to standardization construction of primary and secondary education in urban (U) and rural (R) areas. The ultimate goal of the integration of urban and rural education is to pursuit quality urban and rural education. Based on analysing the related policy basis and the existing assessment models…

Secondary standard dosimetry laboratory at the Ruder Boskovic Institute, Zagreb, Croatia

International Nuclear Information System (INIS)

Vekic, B.; Ban, R.; Saveta, M.

2006-01-01

The Secondary Standard Dosimetry Laboratory at the Ruder Boskovic Institute, Zagreb, Croatia, was installed during the several last years. The installation of this Laboratory was strongly supported by the International Atomic Energy Agency (IAEA) through the Technical Cooperation Project (C.R.O. 1/004/; Establishing Calibration Services). Inside the country this Technical Cooperation Project was supported by the State Office for Standardization and Metrology, State Office for Radiation Protection and the Ministry of Health of the Republic of Croatia. The Secondary Standard Dosimetry Laboratory at the Ruder Boskovic Institute, Zagreb, Croatia was installed in two calibration rooms. The both of these calibration rooms are 9.6 meters long and 6 meters wide. In the both of these calibration rooms the proper air conditioning was installed. The walls of the both calibration rooms are thick enough (1 meter of concrete) and the entrance doors are protected by Pb to protect any radiation hazard in control rooms, in neighbouring rooms and in environment. In the first calibration room, placed in the basement, two sealed sources share the same calibration bench (produced by Hopewell Designs, Inc., USA) between them which is 6 meters long. On one side is Co -60 source of the 30 TBq activity (December 2004) for the calibration of radiotherapy ionizing chambers and the other equipment in the field of high dose rate range. On the other side is irradiation unit consists of 2 sealed sources for radiation protection purposes: (1) Cs-137 source, activity of 740 MBq (February 2004) and (2) Co- 60 source, activity of 185 MBq (February 2004). For this second source three attenuators are provided that give a nominal attenuation of *10, *100 and *1000. In the second calibration room placed just above the first one the X -ray unit (gift from P.T.B., Germany, I.S.O.V.O.L.T. 420, 40 -300 kV, 1-20 mA) is placed. In front of this are: (1.) Aperture Wheel Assembly designed to modify the beam

Calibration and consistency of results of an ionization-chamber secondary standard measuring system for activity

International Nuclear Information System (INIS)

Schrader, Heinrich

2000-01-01

Calibration in terms of activity of the ionization-chamber secondary standard measuring systems at the PTB is described. The measurement results of a Centronic IG12/A20, a Vinten ISOCAL IV and a radionuclide calibrator chamber for nuclear medicine applications are discussed, their energy-dependent efficiency curves established and the consistency checked using recently evaluated radionuclide decay data. Criteria for evaluating and transferring calibration factors (or efficiencies) are given

Final Air Toxics Standards for Clay Ceramics Manufacturing, Glass Manufacturing, and Secondary Nonferrous Metals Processing Area Sources Fact Sheet

Science.gov (United States)

This page contains a December 2007 fact sheet with information regarding the National Emissions Standards for Hazardous Air Pollutants (NESHAP) for Clay Ceramics Manufacturing, Glass Manufacturing, and Secondary Nonferrous Metals Processing Area Sources

Automatic Exchange of Information as the new global standard: the end of (offshore tax evasion) history?

OpenAIRE

Meinzer, Markus

2017-01-01

Automatic exchange of information (AEoI) for tax purposes has become the global standard for international tax cooperation in 2013. As a tool for containing offshore tax evasion, it has encountered opposition in the past and continues to be fraught with challenges. This paper recapitulates the rationale for AEoI, including estimates on the magnitudes of assets held offshore, with a specific focus on Turkish assets held in Germany (chapter 1). Subsequently, chapter 2 summarises the recent hist...

Foreign Exchange Reserves: Bangladesh Perspective

Directory of Open Access Journals (Sweden)

Md Zahangir Alam

2013-10-01

Full Text Available This study is about foreign exchangereserves of Bangladesh. The mainpurpose of this study is to the influence of exchange rates on foreign exchangereserves to the Bangladesh context.  Both the primary and secondary data has been used inthis study. The primary data has been collected through a structuredquestionnaire from 50 respondents. The secondary data, namely Bangladeshforeign exchange reserves (FER, Bangladesh current account balance (CAB,Bangladesh capital andfinancial account balance (CFAB, and BDT/USD exchange rates (ER.  This study covers yearly data from July 01,1996 to June 30, 2005 and quarterly data from July 01, 2005 to June 30, 2012. Findingsof this study shows that out of the selected 16 factors affecting foreignexchange reserves, exchange rates occupy the first position, weighted averagescore (WAS being 4.56. Foreign exchange reserves (FER and current accountbalance (CAB have increased by 502.9087% and 1451.218%,whereas capital and financial account (CFAB has decreased by -649.024% on June30, 2012 compared to June 30, 1997. The influence of other factors heldconstant, as ER changes by 285.6894 units due to one unit change in FER, onaverage in the same direction which represents that ER has positive effect on theFER and this relationship is statistically significant.  62.1526 percentof the variation in FER is explained by ER. The outcomes of Breusch-Godfrey test (LM test, ARCHtest, and the Normality test are that there is a serial correlation among residuals, the variance of residuals is notconstant, and the residuals are not normally distributed.

Ion exchange in ZSM-5 zeolite

International Nuclear Information System (INIS)

Matthews, D.P.; Rees, L.V.C.

1986-01-01

The ion exchange properties of Na-ZSM5 have been studied using a number of univalent and divalent cations at 25degC and 65degC. All the univalent cations studied achieved 100 per cent exchange. The thermodynamic affinity sequence Cs > Rb=NH 4 =H 3 O>K>Na>Li was found at both temperatures for a sample with Si/Al=39. Standard enthalpies of exchange ΔH o were calculated using the van't' Hoff isochore and standard entropies of exchange were then calculated from ΔH o and ΔG o . Multivalent cations were unable to achieve 100 per cent exchange. The maximum exchange was found to increase through the series Ca 2+ cations ( 57 Fe enriched) on dehydration and rehydration following sorption and desorption of ethanol. At least 3 sites for Fe 2+ were observed in the dehydrated zeolite. (author)

Specific pathologist responses for Standard for Exchange of Nonclinical Data (SEND).

Science.gov (United States)

Watanabe, Atsushi; Kusuoka, Osamu; Sato, Norihiro; Nakazono, Osamu; Wasko, Michael; Potenta, Daniel; Nakae, Dai; Hatakeyama, Hirofumi; Iwata, Hijiri; Naota, Misaki; Anzai, Takayuki

2017-07-01

The Standard for Exchange of Nonclinical Data (SEND), introduced by the US Food and Drug Administration (FDA), is a scheme for the computerization, electronic application, and screening of preclinical data. Since its establishment, related organizations have been working together to implement SEND. However, it is difficult for individual pharmaceutical companies that often outsource to achieve complete compliance with SEND; hence, the cooperation of contract research organizations (CROs) and SEND Registered Solution Providers (RSPs) is indispensable. In SEND, most data, including those on pathology findings, are converted into controlled terminology (CT), but it is not a simple process to convert findings or levels of severity in the field of pathology, which is a descriptive science. The authors have successfully completed an FDA trial submission for a toxicology test conducted at a CRO and in doing so acquired important knowledge. This article presents a clear picture of such important knowledge from a pathologist's viewpoint.

Effective international information exchange as a key element of modern tax systems: promises and pitfalls of the OECD’s common reporting standard

Directory of Open Access Journals (Sweden)

Stjepan Gadzo

2017-06-01

Full Text Available Today’s global economic environment is characterized by the high mobility of capital and labour across national borders. Against the backdrop of a legal framework governing taxation of cross-border income, this may lead to double taxation on the one hand, as well as provide opportunities for tax evasion and tax avoidance on the other. It is well-established that a prerequisite for effective taxation of foreign-sourced income earned by “domestic taxpayers” (i.e. tax residents is the system of administrative co-operation across national boundaries, mainly in the form of exchange of tax-relevant information between tax authorities. Since the lack of information-exchange mechanisms is linked with tax havens and the proliferation of “harmful tax practices”, the OECD put the issue high on the global political agenda as early as 1998. Further developments strengthened the importance of the exchange of information, leading to the so-called “big bang” of 2009, i.e. to a significant increase in the number of concluded tax information exchange agreements, caused by the growing concern about international tax evasion and avoidance in the post-crisis period.Nowadays the so-called automatic exchange of information (AEOI between tax authorities has emerged as a new global standard. This is mostly due to the development of specific national and international models, aimed at enhancing intergovernmental cooperation in fighting offshore tax evasion. In this regard special attention should be drawn to the 2014 release of the OECD’s Common Reporting Standard (CRS, which is based on the idea that banks and other financial institutions should play a crucial role in providing information on taxpayer’s income and assets to tax authorities around the globe.The aim of this paper is to explore some of the most important implications of the adoption of the CRS as a global AEOI model. While there are marked advantages of the new standard - mainly related

Standard practice for in situ examination of ferromagnetic Heat-Exchanger tubes using remote field testing

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This practice describes procedures to be followed during remote field examination of installed ferromagnetic heat-exchanger tubing for baseline and service-induced discontinuities. 1.2 This practice is intended for use on ferromagnetic tubes with outside diameters from 0.500 to 2.000 in. [12.70 to 50.80 mm], with wall thicknesses in the range from 0.028 to 0.134 in. [0.71 to 3.40 mm]. 1.3 This practice does not establish tube acceptance criteria; the tube acceptance criteria must be specified by the using parties. 1.4 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this practice to establ...

Map Specifications and Exchange of Geographical Information

DEFF Research Database (Denmark)

Frederiksen, Poul

1999-01-01

Specifications for Technical Maps 1993 – 99 are described giving an overview of the specification structure including the object description of the latest version: TK99.The technical map specifications are related to the standards for topographical maps - especially the TOP10DK standard. Common...... object definitions are essential for the standards. Technical as well as topographical map information is exchangeable through the Danish developed “Standard for Exchange of Digital Map Information”, known as the DSFL-format....

78 FR 40241 - Self-Regulatory Organizations; BATS Exchange, Inc.; Notice of Filing of a Proposed Rule Change To...

Science.gov (United States)

2013-07-03

... conducted on a daily basis, and (ii) a secondary data center, which is predominantly maintained for business... one or more data centers other than the Exchange's primary or secondary data center (``Remote Data... provide participants that may not have a presence at the Exchange's primary or secondary data center with...

Test procedure for cation exchange chromatography

International Nuclear Information System (INIS)

Cooper, T.D.

1994-01-01

The purpose of this test plan is to demonstrate the synthesis of inorganic antimonate ion exchangers and compare their performance against the standard organic cation exchangers. Of particular interest is the degradation rate of both inorganic and organic cation exchangers. This degradation rate will be tracked by determining the ion exchange capacity and thermal stability as a function of time, radiation dose, and chemical reaction

Calibration of the NPL secondary standard radionuclide calibrator for the new 10R Schott, Type 1+ vials

International Nuclear Information System (INIS)

Baker, M.

2005-01-01

For many years, P6 vials have been used for the distribution of a wide range of diagnostic and therapeutic radioactive solutions. The activity measurements were performed in this geometry and, in time, the UK calibration system for nuclear medicine was based on this container as a standard. However, one major supplier of radiopharmaceuticals has replaced the P6 vial with the 10R Type 1+ Schott vial. As the dimensions of the new vial are different from those of the P6 vial and the responses of radionuclide calibrators are known to be container dependent, the need for re-calibration became apparent. Preliminary measurements made on some typical radionuclide calibrators for 125 I solution indicated a difference in response of about 10% between the two vials. The master ionisation chamber of the NPL secondary standard radionuclide calibrator has been re-calibrated and new calibration factors and volume correction factors for 10R Schott vials have been derived for the relevant medical radionuclides. The standard holder was also modified to accommodate the new larger vial. The complete list of factors and the method used to determine them is presented in this paper. The availability of these new factors will improve the quality of activity measurements in nuclear medicine, as calibration services can now be provided by NPL for the new container. These factors can also be employed for all commercial NPL secondary standard radionuclide calibrators (now known as the NPL-CRC and previously as the 671 or ISOCAL IV)

Nanomaterials-Enhanced Electrically Switched Ion Exchange Process for Water Treatment

International Nuclear Information System (INIS)

Lin, Yuehe; Choi, Daiwon; Wang, Jun; Bontha, Jagannadha R.

2009-01-01

The objective of our work is to develop an electrically switched ion exchange (ESIX) system based on conducting polymer/carbon nanotube (CNT) nanocomposites as a new and cost-effective approach for removal of radioactive cesium, chromate, and perchlorate from contaminated groundwater. The ESIX technology combines ion exchange and electrochemistry to provide a selective, reversible method for the removal of target species from wastewater. In this technique, an electroactive ion exchange layer is deposited on a conducting substrate, and ion uptake and elution are controlled directly by modulation of the potential of the layer. ESIX offers the advantages of highly-efficient use of electrical energy combined with no secondary waste generation. Recently, we have improved upon the ESIX process by modifying the conducting substrate with carbon nanotubes prior to the deposition of the electroactive ion exchanger. The nanomaterial-based electroactive ion exchange technology will remove cesium-137, chromate, and perchlorate rapidly from wastewater. The high porosity and high surface area of the electroactive ion exchange nanocomposites results in high loading capacity and minimize interferences for non-target species. Since the ion adsorption/desorption is controlled electrically without generating a secondary waste, this electrically active ion exchange process is a green process technology that will greatly reduce operating costs

Kinetics of hydrogen isotope exchange reactions

International Nuclear Information System (INIS)

Gold, V.; McAdam, M.E.

1975-01-01

Under the influence of tritium β-radiation, 1,4-dioxan undergoes hydrogen exchange with the solvent water. The inhibition of the reaction by known electron scavengers (Ag + , Cu 2+ , Ni 2+ , Co 2+ , Zn 2+ , H 3 + O) and also by species with high reactivity towards hydroxyl radicals but negligible reactivity towards solvated electrons (N 3 - , Br - , SCN - ) has been examined in detail. γ-irradiation similarly induces hydrogen exchange. The action of scavengers is interpreted as requiring the involvement of two separately scavengeable primary radiolysis products in the sequence of reactions leading to exchange. The presence of electron scavengers, even at high concentration, does not totally inhibit the exchange, and a secondary exchange route, involving a low vacancy state of inhibitor cations, is considered responsible for the 'unscavengeable' portion of the reaction, by providing an alternative exchange route. Analogies are drawn between the exchange reaction and other radiation-induced reactions that are thought to involve spur processes. Some implication of radiation-chemical studies in water-alcohol mixtures are indicated. (author)

Quality control of secondary standards and calibration systems, therapy level, of National Laboratory of Metrology from Ionizing Radiations (LNMRI)

International Nuclear Information System (INIS)

Cecatti, E.R.; Freitas, L.C. de

1992-01-01

The results of quality control program of secondary standards, therapy level, and the calibration system of clinical dosemeters were analysed from 1984, when a change in the laboratory installation occurred and new standards were obtained. The national and the international intercomparisons were emphasised. The results for graphite wall chambers were compared, observing a maximum variation of about 0,6%. In the case of Delrin (TK01) wall chambers, the maximum variation was 1,7%. The results of post intercomparisons with thermoluminescent dosemeters have presented derivations lesser than 1%, securing the standards consistence at LNMRI with the international metrological system. (C.G.C.)

Metrological characteristics of the new BSS2 beta secondary standard system

International Nuclear Information System (INIS)

Reynaldo, Sibele R.

2005-01-01

Due to the increased interest and the importance of beta radiation dosimetry for radiation protection purposes, the Centro de Desenvolvimento da Tecnologia Nuclear. MG, Brazil, acquired the newest Beta Secondary Standard system (BSS2) in order to replace the old BSS1 model, with the goal of implement a beta radiation metrology laboratory and provide the corresponding reference radiation. The new system BSS2, unique in Latin America, requires operational testing and metrological characterization for reliability purposes. For this, some comparative investigations of the two systems were made. The influence of opening and closing the shutter in the final dose of radiation was identified as the highest in the BSS2 in relation to the one founded in BSS1, justified by the structural difference of the shutters of the systems and the reproducibility of source-detector geometry was better in BSS2, because of the robustness of the same

Air kerma standardization for diagnostic radiology in a secondary standard laboratory

International Nuclear Information System (INIS)

Ramos, Manoel M.O.; Peixoto, J. Guilherme P.; Lopes, Ricardo T.

2009-01-01

The demand for calibration services and quality control in diagnostic radiology has grown in the country since the publication of the governmental regulation 453, issued by the Brazilian Ministry of Health in 1998. At that time, to produce results facing the new legislation, many laboratories used different standards and radiation qualities, some of which could be inadequate. The international standards neither supplied consistent radiation qualities and standardization for the different types of equipment available. This situation changed with the publication of the new edition of the IEC 61267 standard, published in 2005. The objective of this work was to implement the standardization of the air kerma for the unatenuated qualities (RQR) of IEC 61267 in the National Laboratory of Metrology of the Ionizing Radiations (LNMRI) of the Institute of Radiation Protection and Dosimetry (IRD). Technical procedures were developed together with uncertainty budget. Results of interlaboratory comparisons demonstrate that the quantity is standardized and internationally traceable. (author)

Inflationary trispectrum from graviton exchange

DEFF Research Database (Denmark)

Seery, David; Sloth, Martin Snoager; Vernizzi, Filippo

2009-01-01

We compute the connected four-point correlation function of the primordial curvature perturbation generated during inflation with standard kinetic terms, where the correlation is established via exchange of a graviton between two pairs of scalar fluctuations. Any such correlation yields a contrib......We compute the connected four-point correlation function of the primordial curvature perturbation generated during inflation with standard kinetic terms, where the correlation is established via exchange of a graviton between two pairs of scalar fluctuations. Any such correlation yields...... where the momentum of the graviton which is exchanged becomes much smaller than the external momenta. We conclude that the total non-linearity parameter generated by single-field models of slow-roll inflation is at maximum tauNL ~ r....

Quantization of secondary ion mass spectrometry (SIMS) data using external and internal standards

International Nuclear Information System (INIS)

Gnaser, H.

1983-01-01

Some aspects of multi-dimensional characterization of solids by secondary ion mass spectrometry (SIMS) are given. A theoretical part discusses methods for the quantization of SIMS data and the most prominent effects of ion-solid interactions as related to SIMS. After a description of the instrument used for experiments (a quadrupole-equipped ion microprobe featuring a liquid metal ion source in addition to the standard duoplasmatron gas ion source) the first experimental section is devoted to the determination of practical sensitivities and relative sensitivity factors for selected pure elements, binary and treary alloys and multicomponent systems. For 23 pure elements practical sensitivities under O + 2 bombardment also have been compared to those under In + -bombardment; it was shown that on oxygen saturated surfaces yields under In + -bombardment are higher, this making feasible use of submicron In-beams for surface analysis. In the second experimental section boron implants in silicon have been used for studying depth profiling capabilities of the instrument. Sputtering yields of Si and degrees of ionization of both B and Si have been measured. It has been shown that implantation profiles may deviate considerably from Gaussian but can be described by means of mathematical distribution functions. In the third experimental section depth resolution of the erosion process has been studied by profiling a Ni/Cr multilayer sample (100 A single layer) and been found to be approximately constant over the depth range investigated. Quantization of depth profiles, usually distorted by matrix effects, has been attempted using the primary beam species (In) as internal implantation standard. Some problems in connection with the conversion of secondary ion micrographs to concentration maps are discussed. Elemental detection limits in multidimensional SIMS analysis are given in dependence of primary beam size and total eroded depth. (Author)

Calibration of ARI QC ionisation chambers using the Australian secondary standards for activity

International Nuclear Information System (INIS)

Mo, L.; Van Der Gaast, H.A.; Alexiev, D.; Butcher, K.S.A.; Davies, J.

1999-01-01

The Secondary Standard Activity Laboratory (SSAL) in ANSTO routinely provides standardised radioactive sources, traceable activity measurements and custom source preparation services to customers. The most important activity carried out is the calibration of ionisation chambers located in the Quality Control (QC) section of Australian Radioisotopes (ARI). This ensures that their activity measurements are traceable to the Australian primary methods of standardisation. ARI QC ionisation chambers are calibrated for 99m Tc, 67 Ga, 131 I, 201 Tl and 153 Sm. The SSAL has a TPA ionisation chamber, which has been directly calibrated against a primary standard for a variety of radioactive nuclides. Calibration factors for this chamber were determined specifically for the actual volumes (5ml for 99m Tc, 131 I, 2ml for 67 Ga, 201 Tl and 3 ml for 153 Sm) and types of vial (Wheaton) which are routinely used at ARI. These calibration factors can be used to accurately measure the activity of samples prepared by ARI. The samples can subsequently be used to calibrate the QC ionisation chambers. QC ionisation chambers are re-calibrated biannually

School lunches v. packed lunches: a comparison of secondary schools in England following the introduction of compulsory school food standards.

Science.gov (United States)

Stevens, Lesley; Nicholas, Jo; Wood, Lesley; Nelson, Michael

2013-06-01

To compare food choices and nutrient intakes of pupils taking a school lunch or a packed lunch in eighty secondary schools in England, following the introduction of the food-based and nutrient-based standards for school food. Cross-sectional data collected between October 2010 and April 2011. Pupils' lunchtime food choices were recorded over five consecutive days. Secondary schools, England. A random selection of 5925 pupils having school lunches and 1805 pupils having a packed lunch in a nationally representative sample of eighty secondary schools in England. The differences in the specific types of food and drink consumed by the two groups of pupils are typical of differences between a hot and cold meal. On average, school lunches as eaten contained significantly more energy, carbohydrate, protein, fibre, vitamin A, folate, Fe and Zn than packed lunches, and 8 % less Na. Although neither school lunches nor packed lunches provided the balance of nutrients required to meet the nutrient-based standards (based on about one-third of daily energy and nutrient requirements), school lunches generally had a healthier nutrient profile, with lower Na and percentage of energy from fat, and higher fibre and micronutrient content. These differences were greater than those reported prior to the introduction of compulsory standards for school lunches. In order to ensure more pupils have a healthy lunch, schools could introduce and enforce a packed lunch policy or make school meals the only option at lunchtime.

Heat exchanger with intermediate evaporating and condensing fluid

International Nuclear Information System (INIS)

Fraas, A.P.

1978-01-01

A shell and tube-type heat exchanger, such as a liquid sodium-operated steam generator for use in nuclear reactors, comprises a shell containing a primary fluid tube bundle, a secondary fluid tube bundle at higher elevation, and an intermediate fluid vaporizing at the surface of the primary fluid tubes and condensing at the surface of the secondary fluid tubes

Development of indicators for patient care and monitoring standards for secondary health care services of Mumbai.

Science.gov (United States)

Malik, Seema S; D'Souza, Roshni Cynthia; Pashte, Pramod Mukund; Satoskar, Smita Manohar; D'Souza, Remilda Joyce

2015-01-01

The Qualitative aspect of health care delivery is one of the major factors in reducing morbidity and mortality in a health care setup. The expanding suburban secondary health care delivery facilities of the Municipal Corporation of Greater Mumbai are an important part of the healthcare backbone of Mumbai and therefore the quality of care delivered here needed standardization. The project was completed over a period of one year from Jan to Dec, 2013 and implemented in three phases. The framework with components and sub-components were developed and formats for data collection were standardized. The benchmarks were based on past performance in the same hospital and probability was used for development of normal range. An Excel spreadsheet was developed to facilitate data analysis. The indicators comprise of 3 components--Statutory Requirements, Patient care & Cure and Administrative efficiency. The measurements made, pointed to the broad areas needing attention. The Indicators for patient care and monitoring standards can be used as a self assessment tool for health care setups for standardization and improvement of delivery of health care services.

Plasma FITC-dextran exchange between the primary and secondary circulatory systems in the Atlantic cod, Gadus Morhua

DEFF Research Database (Denmark)

Fischer, Claes; Steffensen, John Fleng

2008-01-01

Fluorescein isothiocyanate dextran (FITC-dextran) exchange between the primary (PCS) and secondary (SCS) circulatory systems in the Atlantic cod, Gadus morhua (Linnaeus, 1752), were studied using 20-kDa (n = 4) and 500-kDa (n = 4) FITC-dextran. In order to give a qualitative perspective...... of the general connection between the PCS and SCS, distribution of plasma-borne tracers (FITC-dextran) in the PCS and SCS were examined. In this study, a total of eight cod were cannulated in the ventral aorta (PCS) and dorsal cutaneous vessel (SCS), for investigation of FITC-dextran disappearance in the PCS...... and its subsequent appearance in the SCS. FITC-dextran of both sizes was found to be in equilibrium between the PCS and SCS in less than 20 min. This indicates a profound connection between the PCS and SCS in the Atlantic cod, and rapid mixing of tracers between the PCS and SCS. The destination...

Marketing Study on Secondary Metal Futures Might be Finished Within This Year

Institute of Scientific and Technical Information of China (English)

2015-01-01

Commissioned by Shanghai Futures Exchange,China Nonferrous Metals Industry Association Secondary Metal Branch is carrying out"Study on development and marketing of secondary nonferrous metal product futures variety"(ADC12 marketing feasibility study),according

The Relationship between Computer and Internet Use and Performance on Standardized Tests by Secondary School Students with Visual Impairments

Science.gov (United States)

Zhou, Li; Griffin-Shirley, Nora; Kelley, Pat; Banda, Devender R.; Lan, William Y.; Parker, Amy T.; Smith, Derrick W.

2012-01-01

Introduction: The study presented here explored the relationship between computer and Internet use and the performance on standardized tests by secondary school students with visual impairments. Methods: With data retrieved from the first three waves (2001-05) of the National Longitudinal Transition Study-2, the correlational study focused on…

77 FR 31059 - Self-Regulatory Organizations; BATS Exchange, Inc.; Notice of Filing and Immediate Effectiveness...

Science.gov (United States)

2012-05-24

... structure for logical ports used to receive Multicast PITCH data from the Exchange, but rather, simply an... logical ports necessary to receive Multicast PITCH data from the Exchange, which is reflected on the... includes one port at the Exchange's primary data center and another port at the Exchange's secondary data...

Process and device for step by step enrichment of deuterium and/or tritium by isotope exchange

International Nuclear Information System (INIS)

Iniotakis, N.; Decken, C.B. von der.

1984-01-01

Deuterium and/or tritium are bound to steam by isotope exchange after permeation through an exchange wall. Primary and secondary flows are guided by the counterflow principle. The secondary side has a metal oxide as oxidation catalyst. The plant can consist of several enrichment stages. The various flows and parts of the plant are described. (PW) [de

Quality control of the NPL-CRC secondary standard system used for activimeters calibration at IPEN, Sao Paulo, Brazil

International Nuclear Information System (INIS)

Martins, Elaine W.; Potiens, Maria da P.A.

2009-01-01

The objective of this study was to establish a quality control program to be applied at the NPL-CRC activimeter secondary standard system, used as reference to comparison in tests made with the work tertiary standard activimeter, Capintec basic CRC R -15BT, both belonging to the Calibration Laboratory of IPEN. The repeatability, reproducibility and the precision tests were performed using a sealed check source of 133 Ba, from Amersham. It was made 70 series of 10 measurements to each activimeter, totaling 1400 measurements. Considering the variation limit of 5% to precision and reproducibility tests in the nuclear medicine services, recommended by the Brazilian standard CNEN-NN-3.05, the results observed in the behavior of the IPEN activimeter were satisfactory. (author)

Triple-membrane reduces need for ion exchange regeneration

International Nuclear Information System (INIS)

Valcour, H.

1989-01-01

Triple-membrane water treatment systems are comprised of ultrafiltration units for pretreatment, electrodialysis reversal primary demineralizers, reverse osmosis secondary demineralizers, portable ion exchange unit polishing demineralizers, and ultraviolet sterilizers. The triple-membrane process is designed to provide an unprecedented degree of pretreatment to maximize efficiency, durability and reliability of the reverse osmosis, whilst reducing the required regeneration frequency of the ion exchange demineralizer by one to two orders of magnitude. (author)

Plate heat exchangers in the power plant industry

International Nuclear Information System (INIS)

Wersel, M.; Ridell, B.

1984-01-01

An increase in heat transfer and stability, small investment, high flexibility, easy maintenance and corrosion resistance are obtained by the design and construction of plate heat exchangers and by the introduction of the herringbone pattern. The plate heat exchanger can be used in nearly 90% of all secondary circuits in powerstations. Examples of its installation are the WYLFA, GENTILLY, RINGHALS and TVO Finland nuclear power-stations. (DG) [de

Towards automatic exchange of information

OpenAIRE

Oberson, Xavier

2015-01-01

This article describes the various steps that led towards automatic exchange of information as the global standard and the issues that remain to be solved. First, the various competing models of exchange information, such as Double Tax Treaty (DTT), TIEA's, FATCA or UE Directives are described with a view to show how they interact between themselves. Second, the so-called Rubik Strategy is summarized and compared with an automatic exchange of information (AEOI). The third part then describes ...

78 FR 30376 - Self-Regulatory Organizations; BATS Y-Exchange, Inc.; Notice of Filing and Immediate...

Science.gov (United States)

2013-05-22

... for ports used to enter orders in the Exchange's trading system and to receive data from the Exchange... primary data center and one port at the Exchange's secondary data center. Rather than stating that the fee... footnote that states that logical port fees are limited to logical ports in the Exchange's primary data...

Feasibility Study of Secondary Heat Exchanger Concepts for the Advanced High Temperature Reactor

Energy Technology Data Exchange (ETDEWEB)

Piyush Sabharwall

2011-09-01

The work reported herein represents a significant step in the preliminary design of heat exchanger options (material options, thermal design, selection and evaluation methodology with existing challenges). The primary purpose of this study is to aid in the development and selection of the required heat exchanger for power production using either a subcritical or supercritical Rankine cycle.

Construction and performance tests of a secondary hydrogen gas cooling system

International Nuclear Information System (INIS)

Sanokawa, K.; Hishida, M.

1980-01-01

With the aim of a multi-purpose use of nuclear energy, such as direct steel-making, an experimental multi-purpose high-temperature gas-cooled reactor (VHTR) is now being developed by the Japan Atomic Energy Research Institute (JAERI). In order to simulate a heat exchanging system between the primary helium gas loop and the secondary reducing gas system of the VHTR, a hydrogen gas loop as a secondary cooling system of the existing helium gas loop was completed in 1977, and was successfully operated for over 2000 hours. The objectives of constructing the H 2 secondary loop were: (1) To get basic knowledge for designing, constructing and operating a high-temperature and high-pressure gas facility; (2) To perform the following tests: (a) hydrogen permeation at the He/H 2 heat exchanger (the surfaces of the heat exchanger tubes are coated by calorizing to reduce hydrogen permeation), (b) thermal performance tests of the He/H 2 heat exchanger and the H 2 /H 2 regenerative heat exchanger, (c) performance test of internal insulation, and (d) performance tests of the components such as a H 2 gas heater and gas purifiers. These tests were carried out at He gas temperature of approximately 1000 0 C, H 2 gas temperature of approximately 900 0 C and gas pressures of approximately 40 kg/cm 2 G, which are almost the same as the operating conditions of the VHTR

XML-based formulation of field theoretical models. A proposal for a future standard and data base for model storage, exchange and cross-checking of results

International Nuclear Information System (INIS)

Demichev, A.; Kryukov, A.; Rodionov, A.

2002-01-01

We propose an XML-based standard for formulation of field theoretical models. The goal of creation of such a standard is to provide a way for an unambiguous exchange and cross-checking of results of computer calculations in high energy physics. At the moment, the suggested standard implies that models under consideration are of the SM or MSSM type (i.e., they are just SM or MSSM, their submodels, smooth modifications or straightforward generalizations). (author)

Efficient Fair Exchange from Identity-Based Signature

Science.gov (United States)

Yum, Dae Hyun; Lee, Pil Joong

A fair exchange scheme is a protocol by which two parties Alice and Bob exchange items or services without allowing either party to gain advantages by quitting prematurely or otherwise misbehaving. To this end, modern cryptographic solutions use a semi-trusted arbitrator who involves only in cases where one party attempts to cheat or simply crashes. We call such a fair exchange scheme optimistic. When no registration is required between the signer and the arbitrator, we say that the fair exchange scheme is setup free. To date, the setup-free optimist fair exchange scheme under the standard RSA assumption was only possible from the generic construction of [12], which uses ring signatures. In this paper, we introduce a new setup-free optimistic fair exchange scheme under the standard RSA assumption. Our scheme uses the GQ identity-based signature and is more efficient than [12]. The construction can also be generalized by using various identity-based signature schemes. Our main technique is to allow each user to choose his (or her) own “random” public key in the identitybased signature scheme.

Back-exchange: a novel approach to quantifying oxygen diffusion and surface exchange in ambient atmospheres.

Science.gov (United States)

Cooper, Samuel J; Niania, Mathew; Hoffmann, Franca; Kilner, John A

2017-05-17

A novel two-step Isotopic Exchange (IE) technique has been developed to investigate the influence of oxygen containing components of ambient air (such as H 2 O and CO 2 ) on the effective surface exchange coefficient (k*) of a common mixed ionic electronic conductor material. The two step 'back-exchange' technique was used to introduce a tracer diffusion profile, which was subsequently measured using Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). The isotopic fraction of oxygen in a dense sample as a function of distance from the surface, before and after the second exchange step, could then be used to determine the surface exchange coefficient in each atmosphere. A new analytical solution was found to the diffusion equation in a semi-infinite domain with a variable surface exchange boundary, for the special case where D* and k* are constant for all exchange steps. This solution validated the results of a numerical, Crank-Nicolson type finite-difference simulation, which was used to extract the parameters from the experimental data. When modelling electrodes, D* and k* are important input parameters, which significantly impact performance. In this study La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF6428) was investigated and it was found that the rate of exchange was increased by around 250% in ambient air compared to high purity oxygen at the same pO 2 . The three experiments performed in this study were used to validate the back-exchange approach and show its utility.

Syringe calibration factors and volume correction factors for the NPL secondary standard radionuclide calibrator

CERN Document Server

Tyler, D K

2002-01-01

The activity assay of a radiopharmaceutical administration to a patient is normally achieved via the use of a radionuclide calibrator. Because of the different geometries and elemental compositions between plastic syringes and glass vials, the calibration factors for syringes may well be significantly different from those for the glass containers. The magnitude of these differences depends on the energies of the emitted photons. For some radionuclides variations have been observed of 70 %, it is therefore important to recalibrate for syringes or use syringe calibration factors. Calibration factors and volume correction factors have been derived for the NPL secondary standard radionuclide calibrator, for a variety of commonly used syringes and needles, for the most commonly used medical radionuclide.

Reamed intramedullary exchange nailing in the operative treatment of aseptic tibial shaft nonunion.

Science.gov (United States)

Hierholzer, Christian; Friederichs, Jan; Glowalla, Claudio; Woltmann, Alexander; Bühren, Volker; von Rüden, Christian

2017-08-01

The aim of this study was to evaluate a standardized treatment protocol regarding the rate of secondary bone union, complications, and functional outcome. This study was started as a prospective study in a single Level I Trauma Centre between 2003 and 2012. The study group consisted of 188 patients with the diagnosis of an aseptic tibial shaft nonunion. Exchange nailing was performed following a standardized surgical protocol. Long-term follow-up was analyzed for rate of bone healing and functional outcome. Osseous healing was achieved in 182 out of 188 patients (97 %). In 165 out of 188 patients (88 %), bone healing was observed timely and uneventfully after a single exchange nailing procedure. An open approach was necessary in 32 patients (17 %). Twenty-three patients (12 %) required additional therapy such as extracorporeal shock wave therapy. Post-operative complications were observed in seven patients (4 %). Almost all patients demonstrated osseous healing within 12 months, with the majority of osseous healing occurring within six months. A relevant shortening of the fractured tibia was observed in 20 out of 188 patients (11 %). After a median follow-up of 23 months (range 12-45 months), outcome was evaluated using the assessment system of Friedman/Wyman. In summary, 154 out of 188 patients (82 %) had a good functional long-term result. Reamed intramedullary exchange nailing including correction of axis alignment is a safe and effective treatment of aseptic tibial shaft nonunion with a high rate of bone healing and a good radiological and functional long-term outcome.

Flexible Exchange of Farming Device Data

DEFF Research Database (Denmark)

Iftikhar, Nadeem; Pedersen, Torben Bach

2011-01-01

A new trend in the farming business is to replace conventional farming devices with computerized farming devices. Accordingly, numerous computer-based farming devices for logging, processing and exchanging data have recently been installed on moving farm machinery such as tractors. The exchange o......-directional data exchange as well as efficient requirements change management through a graphical user interface. The paper also demonstrates the use of the proposed solution based on a farming case study and open source technologies....... and systems to exchange data based on a predefined set of rules. In consequence, many hand-coded data exchange solutions have been developed in the farming business. Although efforts regarding incorporating data exchange standards have been made, their actual usage so far has been limited, due to the fact...

Effective exchange potentials for electronically inelastic scattering

International Nuclear Information System (INIS)

Schwenke, D.W.; Staszewska, G.; Truhlar, D.G.

1983-01-01

We propose new methods for solving the electron scattering close coupling equations employing equivalent local exchange potentials in place of the continuum-multiconfiguration-Hartree--Fock-type exchange kernels. The local exchange potentials are Hermitian. They have the correct symmetry for any symmetries of excited electronic states included in the close coupling expansion, and they have the same limit at very high energy as previously employed exchange potentials. Comparison of numerical calculations employing the new exchange potentials with the results obtained with the standard nonlocal exchange kernels shows that the new exchange potentials are more accurate than the local exchange approximations previously available for electronically inelastic scattering. We anticipate that the new approximations will be most useful for intermediate-energy electronically inelastic electron--molecule scattering

Progress Report for Diffusion Welding of the NGNP Process Application Heat Exchangers

Energy Technology Data Exchange (ETDEWEB)

R.E. Mizia; D.E. Clark; M.V. Glazoff; T.E. Lister; T.L. Trowbridge

2011-12-01

The U.S. Department of Energy selected the high temperature gas-cooled reactor as the basis for the Next Generation Nuclear Plant (NGNP). The NGNP will demonstrate the use of nuclear power for electricity, hydrogen production, and process heat applications. The NGNP Project is currently investigating the use of metallic, diffusion welded, compact heat exchangers to transfer heat from the primary (reactor side) heat transport system to the secondary heat transport system. An intermediate heat exchanger will transfer this heat to downstream applications such as hydrogen production, process heat, and electricity generation. The channeled plates that make up the heat transfer surfaces of the intermediate heat exchanger will have to be assembled into an array by diffusion welding. This report describes the preliminary results of a scoping study that evaluated the diffusion welding process parameters and the resultant mechanical properties of diffusion welded joints using Alloy 800H. The long-term goal of the program is to progress towards demonstration of small heat exchanger unit cells fabricated with diffusion welds. Demonstration through mechanical testing of the unit cells will support American Society of Mechanical Engineers rules and standards development, reduce technical risk, and provide proof of concept for heat exchanger fabrication methods needed to deploy heat exchangers in several potential NGNP configurations.1 Researchers also evaluated the usefulness of modern thermodynamic and diffusion computational tools (Thermo-Calc and Dictra) in optimizing the parameters for diffusion welding of Alloy 800H. The modeling efforts suggested a temperature of 1150 C for 1 hour with an applied pressure of 5 MPa using 15 {micro}m nickel foil as joint filler to reduce chromium oxidation on the welded surfaces. Good agreement between modeled and experimentally determined concentration gradients was achieved

Telephone Exchange Maintenance

CERN Multimedia

2005-01-01

Urgent maintenance work on CERN telephone exchanges will be performed on 24 March from 6 a.m. to 8 a.m. Telephone services may be disrupted or even interrupted during this time. For more details, please contact us by email at Standard.Telephone@cern.ch.

Exploitation of secondary standard for calibration in units of Dw,1cm and assessment of several HDR brachytherapy planning systems

International Nuclear Information System (INIS)

Gabris, F.; Zeman, J.; Valenta, J.; Gabris, F.; Selbach, H.J.

2012-01-01

A secondary standard of the BEV, calibrated at the PTB in terms of D w,1c m, was used for calibration of the well-type chamber-based measuring systems used in clinics. In addition to the calibration, we tried to employ it for assessment of treatment planning systems (TPS) used for each particular after-loader. The dose to water at 1 cm distance from the source position was calculated by the TPS, using reference data from the source producer certificate. The values were compared directly with the dose measured at the same distance from the source. The comparison has been carried out for GammaMed Plus and MicroSelectron HDR sources. Differences of secondary standard measurements and TPS calculations were lower than ±5%, which is below the achievable uncertainty of both dose measurement and dose determination by the TPS. Nevertheless, it is higher than generally accepted in the case of external beam radiotherapy. Additional direct measurements in terms of D w,1c m may improve the safety and reliability of patient treatment. (authors)

17 CFR 155.4 - Trading standards for introducing brokers.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Trading standards for introducing brokers. 155.4 Section 155.4 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION TRADING STANDARDS § 155.4 Trading standards for introducing brokers. (a) Each introducing broker...

Cleaning of the heat exchanger, Task 3.08/04-01; Zadatak 3.08/04-01 - Ciscenje razmenjivaca toplote

Energy Technology Data Exchange (ETDEWEB)

Nikolic, M; Bratic, A; Milosevic, M [Institute of Nuclear Sciences Boris Kidric, Reaktor RA, Vinca, Beograd (Serbia and Montenegro)

1963-12-15

A problem of decreased cooling appeared after longer operation of the reactor at nominal power of 6.5 MW. The reason of increased coolant temperature in the primary coolant loop and lower temperatures in the secondary coolant loop indicated problems to be related to heat exchangers. Deposits of sand and sludge in the secondary coolant pipes caused decrease of he flow, i.e. decrease of the effective surface for heat exchange. Cleaning of the heat exchanger pipes demanded detailed radiation protection plan to avoid higher exposure of the 74 staff members involved in the operation.

Modeling a Printed Circuit Heat Exchanger with RELAP5-3D for the Next Generation Nuclear Plant

International Nuclear Information System (INIS)

2010-01-01

The main purpose of this report is to design a printed circuit heat exchanger (PCHE) for the Next Generation Nuclear Plant and carry out Loss of Coolant Accident (LOCA) simulation using RELAP5-3D. Helium was chosen as the coolant in the primary and secondary sides of the heat exchanger. The design of PCHE is critical for the LOCA simulations. For purposes of simplicity, a straight channel configuration was assumed. A parallel intermediate heat exchanger configuration was assumed for the RELAP5 model design. The RELAP5 modeling also required the semicircular channels in the heat exchanger to be mapped to rectangular channels. The initial RELAP5 run outputs steady state conditions which were then compared to the heat exchanger performance theory to ensure accurate design is being simulated. An exponential loss of pressure transient was simulated. This LOCA describes a loss of coolant pressure in the primary side over a 20 second time period. The results for the simulation indicate that heat is initially transferred from the primary loop to the secondary loop, but after the loss of pressure occurs, heat transfers from the secondary loop to the primary loop.

Efficacy of standard and intensive statin treatment for the secondary prevention of cardiovascular and cerebrovascular events in diabetes patients : A meta-analysis

NARCIS (Netherlands)

De Vries, Folgerdiena M.; Kolthof, Johan; Postma, Maarten J.; Denig, Petra; Hak, Eelko

2014-01-01

Aims: To estimate the efficacy of standard and intensive statin treatment in the secondary prevention of major cardiovascular and cerebrovascular events in diabetes patients. Methods: A systematic search was conducted in Medline over the years 1990 to September 2013. Randomized, double-blind,

Secondary Low-Level Waste Treatment Strategy Analysis

International Nuclear Information System (INIS)

D.M. LaRue

1999-01-01

The objective of this analysis is to identify and review potential options for processing and disposing of the secondary low-level waste (LLW) that will be generated through operation of the Monitored Geologic Repository (MGR). An estimate of annual secondary LLW is generated utilizing the mechanism established in ''Secondary Waste Treatment Analysis'' (Reference 8.1) and ''Secondary Low-Level Waste Generation Rate Analysis'' (Reference 8.5). The secondary LLW quantities are based on the spent fuel and high-level waste (HLW) arrival schedule as defined in the ''Controlled Design Assumptions Document'' (CDA) (Reference 8.6). This analysis presents estimates of the quantities of LLW in its various forms. A review of applicable laws, codes, and standards is discussed, and a synopsis of those applicable laws, codes, and standards and their impacts on potential processing and disposal options is presented. The analysis identifies viable processing/disposal options in light of the existing laws, codes, and standards, and then evaluates these options in regard to: (1) Process and equipment requirements; (2) LLW disposal volumes; and (3) Facility requirements

Construction Operations Building Information Exchange (COBIE): Requirements Definition and Pilot Implementation Standard

Science.gov (United States)

2007-06-01

Swalley U.S. Department of State, Overseas Buildings Operations Toby Wilson U.S. Army, Corps of Engineers, Engineer R&D Center Jeff Wix AEC3 The...exchanged in COBIE. To map those information exchanges to the IFC model, the Information Delivery Manual (IDM) process [ Wix 2007] was also used. The...Folksonomy. Wikimedia Foundation. http://en.wikipedia.org/wiki/Folksonomy/, accessed 3 August 2007. Wix , Jeffrey. 2007. Information Delivery Manual

45 CFR 170.205 - Content exchange standards and implementation specifications for exchanging electronic health...

Science.gov (United States)

2010-10-01

.... The Healthcare Information Technology Standards Panel (HITSP) Summary Documents Using HL7 CCD... HEALTH AND HUMAN SERVICES HEALTH INFORMATION TECHNOLOGY HEALTH INFORMATION TECHNOLOGY STANDARDS... TECHNOLOGY Standards and Implementation Specifications for Health Information Technology § 170.205 Content...

Progress Report for Diffusion Welding of the NGNP Process Application Heat Exchangers

Energy Technology Data Exchange (ETDEWEB)

R.E. Mizia; D.E. Clark; M.V. Glazoff; T.E. Lister; T.L. Trowbridge

2011-04-01

The NGNP Project is currently investigating the use of metallic, diffusion welded, compact heat exchangers to transfer heat from the primary (reactor side) heat transport system to the secondary heat transport system. The intermediate heat exchanger will transfer this heat to downstream applications such as hydrogen production, process heat, and electricity generation. The channeled plates that make up the heat transfer surfaces of the intermediate heat exchanger will have to be assembled into an array by diffusion welding.

17 CFR 155.2 - Trading standards for floor brokers.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Trading standards for floor brokers. 155.2 Section 155.2 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION TRADING STANDARDS § 155.2 Trading standards for floor brokers. Each contract market shall adopt and submit...

International information exchange in fusion research

International Nuclear Information System (INIS)

Strickler, C.S.

1979-01-01

Formal and informal agreements exist between the US and several other countries, assuring the unrestricted exchange of magnetic fusion information. The Fusion Energy Library at Oak Ridge National Laboratory uses the US Department of Energy standard distribution system and exchange agreements to ensure the receipt of current reports. Selective dissemination of information, computer networks, and exchange programs are additional means for information gathering. The importance of these means as they relate to the fusion program in the US and specifically at ORNL is discussed

The use of fibrous ion exchangers in gold hydrometallurgy

Science.gov (United States)

Kautzmann, R. M.; Sampaio, C. H.; Cortina, J. L.; Soldatov, V.; Shunkevich, A.

2002-10-01

This article examines a family of ion-exchange fibers, FIBAN, containing primary and secondary amine groups. These ion exchangers have a fiber diameter of 20 40 Μm, high osmotic and mechanic stability, a high rate of adsorption and regeneration, and excellent dynamic characteristics as filtering media. Inparticular, this article discusses the use of FIBAN fibrous ion exchangers in the recovery of gold cyanide andbase-metal cyanides (copper and mercury) from mineral-leaching solutions. The influence of polymer structure and water content on their extraction ability is described, along with key parameters of gold hydrometallurgy such as extraction efficiency, selectivity, pH dependence, gold cyanide loading, kinetics, and stripping.

Arrangement between the International Atomic Energy Agency and the World Health Organization concerning the establishment and operation of a network of Secondary Standard Dosimetry Laboratories

International Nuclear Information System (INIS)

1986-01-01

The International Atomic Energy Agency (IAEA) and the World Health Organization (WHO), recognizing that they have been co-operating in the operation of a network of Secondary Standard Dosimetry Laboratories (the Network), established pursuant to a Working Arrangement, dated 5 April 1976; and desiring to continue this co-operation in accordance with Article V of the relationship agreement concluded by IAEA and WHO in 1959; hereby enter a new arrangement to guide their work in operating the Network and providing assistance, when needed, to individual Secondary Standard Dosimetry Laboratories (SSDLs). The purpose of this Arrangement is to set forth responsibilities of IAEA and WHO in the operation and support of the Network and to establish criteria for SSDLs

Monte-Carlo validation of secondary sodium activation in a pool-type LMFBR

International Nuclear Information System (INIS)

Plamiotti, G.; Rado, V.; Salvatores, M.

1980-09-01

The secondary sodium activation in a pool-type LMFBR is the main parameter to be accurately evaluated in the shield design. In the present work a complete two dimensional description of the system, including core, shielding and sodium up to Heat Exchangers, is coupled to local Heat Exchanger Monte-Carlo calculations. This refined calculation is used to deduce a simplified method to take into account the coupling of radial propagation in the Heat Exchanger and its finite cylindrical structure

Exaggerated, Mispredicted, and Misplaced: When "It's the Thought That Counts" in Gift Exchanges

Science.gov (United States)

Zhang, Yan; Epley, Nicholas

2012-01-01

Gift-giving involves both the objective value of a gift and the symbolic meaning of the exchange. The objective value is sometimes considered of secondary importance as when people claim, "It's the thought that counts." We evaluated when and how mental state inferences count in gift exchanges. Because considering another's thoughts requires…

Multiprocessor shared-memory information exchange

International Nuclear Information System (INIS)

Santoline, L.L.; Bowers, M.D.; Crew, A.W.; Roslund, C.J.; Ghrist, W.D. III

1989-01-01

In distributed microprocessor-based instrumentation and control systems, the inter-and intra-subsystem communication requirements ultimately form the basis for the overall system architecture. This paper describes a software protocol which addresses the intra-subsystem communications problem. Specifically the protocol allows for multiple processors to exchange information via a shared-memory interface. The authors primary goal is to provide a reliable means for information to be exchanged between central application processor boards (masters) and dedicated function processor boards (slaves) in a single computer chassis. The resultant Multiprocessor Shared-Memory Information Exchange (MSMIE) protocol, a standard master-slave shared-memory interface suitable for use in nuclear safety systems, is designed to pass unidirectional buffers of information between the processors while providing a minimum, deterministic cycle time for this data exchange

The determinants of exchange rates and the movements of EUR/RON exchange rate via non-linear stochastic processes

Directory of Open Access Journals (Sweden)

Petrică Andreea-Cristina

2017-07-01

Full Text Available Modeling exchange rate volatility became an important topic for research debate starting with 1973, when many countries switched to floating exchange rate system. In this paper, we focus on the EUR/RON exchange rate both as an economic measure and present the implied economic links, and also as a financial investment and analyze its movements and fluctuations through two volatility stochastic processes: the Standard Generalized Autoregressive Conditionally Heteroscedastic Model (GARCH and the Exponential Generalized Autoregressive Conditionally Heteroscedastic Model (EGARCH. The objective of the conditional variance processes is to capture dependency in the return series of the EUR/RON exchange rate. On this account, analyzing exchange rates could be seen as the input for economic decisions regarding Romanian macroeconomics - the exchange rates being influenced by many factors such as: interest rates, inflation, trading relationships with other countries (imports and exports, or investments - portfolio optimization, risk management, asset pricing. Therefore, we talk about political stability and economic performance of a country that represents a link between the two types of inputs mentioned above and influences both the macroeconomics and the investments. Based on time-varying volatility, we examine implied volatility of daily returns of EUR/RON exchange rate using the standard GARCH model and the asymmetric EGARCH model, whose parameters are estimated through the maximum likelihood method and the error terms follow two distributions (Normal and Student’s t. The empirical results show EGARCH(2,1 with Asymmetric order 2 and Student’s t error terms distribution performs better than all the estimated standard GARCH models (GARCH(1,1, GARCH(1,2, GARCH(2,1 and GARCH(2,2. This conclusion is supported by the major advantage of the EGARCH model compared to the GARCH model which consists in allowing good and bad news having different impact on the

Magnetite deposition in PWR secondary systems

International Nuclear Information System (INIS)

Schneider, V.; Riess, R.; Ruehle, W.

2000-01-01

Recently, local magnetite (Fe 3 04) deposition has been observed at various locations within the secondary systems of Siemens-designed PWRs. These deposits sometimes limited operational flexibility and affected routine operation checks. In addition, these deposits may affect the heat transfer characteristics of heat exchangers. Prior to replacement of components or piping or other extensive maintenance activities it should be investigated whether any modification in secondary-side water chemistry might counteract this corrosion phenomenon, which has proven very effective in maintaining steam generator performance. A VGB study will make an assessment of available field information, and countermeasures will be elaborated. This paper describes the current status of the project. (orig.) [de

The performance of a new gas to gas heat exchanger with strip fin

NARCIS (Netherlands)

Wang, J.; Hirs, Gerard; Rollmann, P.

1999-01-01

A compact gas to gas heat exchanger needs large heat transfer areas on both fluid sides. This can be realised by adding secondary surfaces. The secondary surfaces are plate fin, strip fin, and louvered fin, etc. The fins extend the heat transfer surfaces and promote turbulence. This paper presents a

Optimization of secondary side water chemistry in TQNPC

International Nuclear Information System (INIS)

Fang Lan

2007-01-01

This article briefly introduces the types of corrosion that may be happened on steam generator heat exchange tubes in Qinshan CANDU6 nuclear power station and chemical effects on corrosion. The water chemistry optimization on minimzing deposition and corrosion of steam generators are introduced. The article summarizes the experiences of plant chemistry control and morpholine operation, providing guidance for optimizing secondary side water chemistry in the future, giving reference on selection of secondary side alkali agent and setting water chemistry specifications for other nuclear power stations. (authors)

Secondary Organic Aerosol Production from Gasoline Vehicle Exhaust: Effects of Engine Technology, Cold Start, and Emission Certification Standard.

Science.gov (United States)

Zhao, Yunliang; Lambe, Andrew T; Saleh, Rawad; Saliba, Georges; Robinson, Allen L

2018-02-06

Secondary organic aerosol (SOA) formation from dilute exhaust from 16 gasoline vehicles was investigated using a potential aerosol mass (PAM) oxidation flow reactor during chassis dynamometer testing using the cold-start unified cycle (UC). Ten vehicles were equipped with gasoline direct injection engines (GDI vehicles) and six with port fuel injection engines (PFI vehicles) certified to a wide range of emissions standards. We measured similar SOA production from GDI and PFI vehicles certified to the same emissions standard; less SOA production from vehicles certified to stricter emissions standards; and, after accounting for differences in gas-particle partitioning, similar effective SOA yields across different engine technologies and certification standards. Therefore the ongoing, dramatic shift from PFI to GDI vehicles in the United States should not alter the contribution of gasoline vehicles to ambient SOA and the natural replacement of older vehicles with newer ones certified to stricter emissions standards should reduce atmospheric SOA levels. Compared to hot operations, cold-start exhaust had lower effective SOA yields, but still contributed more SOA overall because of substantially higher organic gas emissions. We demonstrate that the PAM reactor can be used as a screening tool for vehicle SOA production by carefully accounting for the effects of the large variations in emission rates.

Forecasting Exchange Rates and Relative Prices with the Hamburger Standard: Is What You Want What You Get With McParity?

OpenAIRE

Robert E. Cumby

1996-01-01

A decade ago the Economist began an annual survey of Big Mac prices as a guide to whether currencies are trading at the right exchange rates. This paper asks how well the hamburger standard has performed. Although average deviations from absolute Big Mac parity are large for several currencies, once estimates of these average deviations are removed from the data, the evidence suggests that convergence to relative Big Mac parity is quite rapid. The half-life of deviations from Big Mac parity a...

Modeling Secondary Neutral Helium in the Heliosphere

International Nuclear Information System (INIS)

Müller, Hans-Reinhard; Möbius, Eberhard; Wood, Brian E.

2016-01-01

An accurate, analytic heliospheric neutral test-particle code for helium atoms from the interstellar medium (ISM) is coupled to global heliospheric models dominated by hydrogen and protons from the solar wind and the ISM. This coupling enables the forward-calculation of secondary helium neutrals from first principles. Secondaries are produced predominantly in the outer heliosheath, upwind of the heliopause, by charge exchange of helium ions with neutral atoms. The forward model integrates the secondary production terms along neutral trajectories and calculates the combined neutral helium phase space density in the innermost heliosphere where it can be related to in-situ observations. The phase space density of the secondary component is lower than that of primary neutral helium, but its presence can change the analysis of primaries and the ISM, and can yield valuable insight into the characteristics of the plasma in the outer heliosheath. (paper)

17 CFR 155.3 - Trading standards for futures commission merchants.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Trading standards for futures commission merchants. 155.3 Section 155.3 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION TRADING STANDARDS § 155.3 Trading standards for futures commission merchants. (a) Each futures...

17 CFR 230.238 - Exemption for standardized options.

Science.gov (United States)

2010-04-01

... options. 230.238 Section 230.238 Commodity and Securities Exchanges SECURITIES AND EXCHANGE COMMISSION... Exemption for standardized options. (a) Exemption. Except as expressly provided in paragraphs (b) and (c) of this section, the Act does not apply to any standardized option, as that term is defined by section 240...

78 FR 51250 - Self-Regulatory Organizations; BATS Exchange, Inc.; Order Approving a Proposed Rule Change To...

Science.gov (United States)

2013-08-20

... conducted on a daily basis, and (ii) a secondary data center, which is predominantly maintained for business... recipients, are required to connect directly to the Exchange at the primary or secondary data centers where... secondary data center (``Remote Data Centers''). PoP ports will be located at Remote Data Centers in order...

Exchange rate policy when the labour market exhibits hysteresis

OpenAIRE

Barry, Frank

1994-01-01

This paper analyzes the effects of exchange rate shocks in a small open economy whose labor market exhibits hysteresis. The model is used to highlight deficiencies in the response of the Irish authorities to exchange rate crisis of 1992/93. A secondary purpose of the paper, though, is to induce those who accept that the Irish labour market is characterised by hysteresis but who reject the argument made here that a more aggressive devaluation should have been pursued, to spell out the labour-m...

Automation of secondary loop operation in Indus-2 LCW plant

International Nuclear Information System (INIS)

Srinivas, L.; Pandey, R.M.; Yadav, R.P.; Gupta, S.; Gandhi, M.L.; Thakurta, A.C.

2013-01-01

Indus-2 Low Conductivity Water (LCW) plant has two loops, primary loop and secondary loop. The primary loop mainly supplies LCW to magnets, power supplies and RF systems at constant flow rate. The secondary loop extracts heat from the primary loop through heat exchangers to maintain the supply water temperature of the primary loop around a set value. The supply water temperature of the primary loop is maintained by operating the pumps and cooling towers in the secondary loop. The desired water flow rate in the secondary loop is met by the manual operation of the required number of the pumps. The automatic operation of the pumps and the cooling towers is proposed to replace the existing inefficient manual operation. It improves the operational reliability and ensures the optimum utilization of the pumps and the cooling towers. An algorithm has been developed using LabView programming to achieve optimized operation of the pumps and the cooling towers by incorporating First-In-First-Out (FIFO) logic. It also takes care of safety interlocks, and generates alarms. The program exchanges input and output signals of the plant using existing SCADA system. In this paper, the development of algorithm, its design and testing are elaborated. In the end, the results obtained thereof are discussed. (author)

Reconsidering Money: Monetary Exchange with Additive Transaction Costs

DEFF Research Database (Denmark)

Schröder, Philipp

2001-01-01

Under the assumption of purely additive transaction costs in exchange, the literature on money has a standard example of direct exchange dominating indirect (monetary) exchange. From here it is frequently concluded that subadditive costs (e.g. search costs) must be examined in order to explain...... money. In contrast, this paper presents an additive transaction costs model in which the mere absence of double coincidences of wants suffices to motivate monetary exchange. Furthermore it is found that not all commodity moneys, that are collectively desirable, qualify for the core, but that all fiat...

Unified communication and standardized data exchange for underground mines; Einheitliche, standardisierte Kommunikation zur Effizienzsteigerung von Bergwerken

Energy Technology Data Exchange (ETDEWEB)

Mueller, C. [Embigence GmbH, Ladbergen (Germany)

2006-11-07

Communication in many forms during the past ten years has changed our daily life: Cellphone technology as well as the Internet are just two examples. In the same way, modern network based communication now starts to change the way how underground mines are run: The lack of proper communication traditionally caused downtime and production loss. In the future, mine communication will be crucial for efficiency and profitability of underground operations. This enables intelligent machines to be used like e.g. a machine server equipped drill rig at LKAB or highly advanced, networked monorail systems at DSK. Standardized communication and information exchange is a basis for using three dimensional visualization tools to support decision finding. The paper explains these visions and goals for the future and explains the feasibility by two running example applications. (orig.)

Standard Test Method for Calibration of Non-Concentrator Photovoltaic Secondary Reference Cells

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This test method covers calibration and characterization of secondary terrestrial photovoltaic reference cells to a desired reference spectral irradiance distribution. The recommended physical requirements for these reference cells are described in Specification E1040. Reference cells are principally used in the determination of the electrical performance of a photovoltaic device. 1.2 Secondary reference cells are calibrated indoors using simulated sunlight or outdoors in natural sunlight by reference to a primary reference cell previously calibrated to the same desired reference spectral irradiance distribution. 1.3 Secondary reference cells calibrated according to this test method will have the same radiometric traceability as the of the primary reference cell used for the calibration. Therefore, if the primary reference cell is traceable to the World Radiometric Reference (WRR, see Test Method E816), the resulting secondary reference cell will also be traceable to the WRR. 1.4 This test method appli...

Thiol-disulfide exchange in peptides derived from human growth hormone.

Science.gov (United States)

Chandrasekhar, Saradha; Epling, Daniel E; Sophocleous, Andreas M; Topp, Elizabeth M

2014-04-01

Disulfide bonds stabilize proteins by cross-linking distant regions into a compact three-dimensional structure. They can also participate in hydrolytic and oxidative pathways to form nonnative disulfide bonds and other reactive species. Such covalent modifications can contribute to protein aggregation. Here, we present experimental data for the mechanism of thiol-disulfide exchange in tryptic peptides derived from human growth hormone in aqueous solution. Reaction kinetics was monitored to investigate the effect of pH (6.0-10.0), temperature (4-50°C), oxidation suppressants [ethylenediaminetetraacetic acid (EDTA) and N2 sparging], and peptide secondary structure (amide cyclized vs. open form). The concentrations of free thiol containing peptides, scrambled disulfides, and native disulfide-linked peptides generated via thiol-disulfide exchange and oxidation reactions were determined using reverse-phase HPLC and liquid chromatography-mass spectrometry. Concentration versus time data were fitted to a mathematical model using nonlinear least squares regression analysis. At all pH values, the model was able to fit the data with R(2) ≥ 0.95. Excluding oxidation suppressants (EDTA and N2 sparging) resulted in an increase in the formation of scrambled disulfides via oxidative pathways but did not influence the intrinsic rate of thiol-disulfide exchange. In addition, peptide secondary structure was found to influence the rate of thiol-disulfide exchange. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

Knowledge Exchange and Management Research: Barriers and Potentials

DEFF Research Database (Denmark)

Bager, Torben

2018-01-01

Purpose: The growing involvement of management researchers in knowledge exchange activities and collaborative research does not seem to be reflected in a growing academic output. The purpose of this paper is to explore barriers for academic output from these activities as well as the potential...... for ‘interesting’ papers. Design/methodology/approach: The paper uses secondary data and statistics as well as an illustrative case study to trace knowledge exchange activities and barriers for academic output based on these activities. Findings: The paper identifies a number of barriers for the turning of data...... derived from knowledge exchange activities and Mode 2 research into academic papers such as low priority of case study research in leading management journals, a growing practice orientation in the research funding systems, methodological challenges due to limited researcher control, and disincentives...

Secondary effects of anion exchange on chloride, sulfate, and lead release: systems approach to corrosion control.

Science.gov (United States)

Willison, Hillary; Boyer, Treavor H

2012-05-01

Water treatment processes can cause secondary changes in water chemistry that alter finished water quality including chloride, sulfate, natural organic matter (NOM), and metal release. Hence, the goal of this research was to provide an improved understanding of the chloride-to-sulfate mass ratio (CSMR) with regards to chloride and sulfate variations at full-scale water treatment plants and corrosion potential under simulated premise plumbing conditions. Laboratory corrosion studies were conducted using Pb-Sn solder/Cu tubing galvanic cells exposed to model waters with low (approx. 5 mg/L Cl(-) and 10 mg/L SO(4)(2-)) and high (approx. 50 mg/L Cl(-) and 100 mg/L SO(4)(2-)) concentrations of chloride and sulfate at a constant CSMR of ≈ 0.5. The role of NOM during corrosion was also evaluated by changing the type of organic material. In addition, full-scale sampling was conducted to quantify the raw water variability of chloride, sulfate, and NOM concentrations and the changes to these parameters from magnetic ion exchange treatment. Test conditions with higher concentrations of chloride and sulfate released significantly more lead than the lower chloride and sulfate test waters. In addition, the source of NOM was a key factor in the amount of lead released with the model organic compounds yielding significantly less lead release than aquatic NOM. Copyright © 2012 Elsevier Ltd. All rights reserved.

Alfa-Laval plate heat exchangers for the power industries

International Nuclear Information System (INIS)

Kitae, Junnosuke; Mtsuura, Kazuyuki

1979-01-01

Within power-generating plants, the transfer and conversion of heat energy of very large quantity are carried out in the process of energy conversion, accordingly the importance of heat exchangers is very high. Heretofore, multi-tube heat exchangers have been used mostly, but Alfa-Laval group developed the heat exchanger with very high efficiency to incorporate it effectively into a power-generating plant. In this plate type heat exchanger, the heat transfer efficiency is very high, and the quantity of stagnation is small as it is compact, consequently it is suitable to the secondary cooling for power-generating plant or the heat exchange of high-priced liquid heat media such as heavy water. Originally, plate type heat exchangers were used for food and chemical industries, therefore the prevention of mixing two liquids, sanitary construction, and corrosion resistance were required. Then they were adopted in iron and steel industry, and large thermal load, large heat transfer area and corrosion resistance to sea water were required. They were adopted in a nuclear power plant for the first time in 1964. In this heat exchanger, channels are formed with corrugated metal sheets, and titanium, stainless steels, Incoloy, Hastelloy and others are used as occasion demands. The Alfa-Laval heat exchangers and their features are explained. (Kako, I.)

The IAEA/WHO Network of SSDLs. Short history, activity and future trends[Secondary Standard Dosimetry Laboratories

Energy Technology Data Exchange (ETDEWEB)

Svensson, Hans; Zsdanszky, Kalman [International Atomic Energy Agency, Dosimtery Section, Vienna (Austria)

1990-04-01

In 1968 at an IAEA meeting in Caracas, Venezuela, the dosimetric requirements of radiotherapy centres were discussed. At that time many radiotherapy departments in developing countries did not have a dosimeter. Even those that had a dosimeter were seldom able to send it to a Primary Standard Dosimetry Laboratory (PSDL) for proper calibration. The establishment of regional dosimeter calibration laboratories was recommended by the participating experts including representatives of WHO. There was general consent that it was not necessary to establish in every country a PSDL, which would need a very qualified staff and sophisticated equipment. Instead, the establishment of Secondary Standard Dosimetry Laboratories (SSDLs) was found to be an adequate solution to the problem. The new idea of SSDLs and their role within the international metrology system was thoroughly discussed at a joint IAEA/WHO meeting in Rio de Janeiro (scientific secretaries: H.H. Eisenlohr, IAEA and W. Seelentag, WHO) in December 1974. Considering the fact that an SSDL cannot work in isolation the experts recommended the setting up of an international Network of SSDLs under the auspices of the IAEA and WHO. The statutes of the IAEA/WHO Network of SSDLs were laid down in a Working Arrangement between the IAEA and WHO in April 1976. Later in 1976 the two Directors General of the IAEA and WHO formally announced by circular letters to their respective member states the establishment of the IAEA/WHO Network of SSDL. The Criteria for the Establishment of a Secondary Standard Dosimetry Laboratory were formulated by an Advisory Group and were attached to these letters. At that time there existed already 8 laboratories, which had been designated by WHO during the period 1968-1976 as regional reference centres for dosimetry. Another SSDL had been set up in Rio de Janeiro in collaboration between the Brazilian Government, the Government of the Federal Republic of Germany, and the IAEA. As a consequence of the

Exchange rate volatility and international trade: The option approach

OpenAIRE

Franke, Günter

1986-01-01

Usually it is argued that an increase in exchange rate volatility reduces the volume of international trade since trading firms are risk averse. This paper shows for risk neutral firms that the expected international trade volume in standardized commodities grows with exchange rate volatility. The firms adjust their trade volume to the exchange rate level. The more favorable the exchange rate is, the higher is the export volume. If the rate drops below some level, exports are stopped. Thus in...

Developing mixed convection in a coiled heat exchanger

NARCIS (Netherlands)

Sillekens, J.J.M.; Rindt, C.C.M.; Steenhoven, van A.A.

1998-01-01

In this paper the development of mixed convection in a helically coiled heat exchanger for Re = 500, Pr = 5 and d = 1/14 is studied. The influence of buoyancy forces (Gr = ¢O (105)) on heat transfer and secondary flow is analyzed. In the method used the parabolized equations are solved using a

[Humidification assessment of four heat and moisture exchanger filters according to ISO 9360: 2000 standard].

Science.gov (United States)

Lannoy, D; Décaudin, B; Resibois, J-P; Barrier, F; Wierre, L; Horrent, S; Batt, C; Moulront, S; Odou, P

2008-02-01

This work consisted of the assessment of humidification parameters and flow resistance for different heat and moisture exchanger filters (HMEF) used in intensive care unit. Four electrostatic HMEF were assessed: Hygrobac S (Tyco); Humidvent compact S (Teleflex); Hygrovent S/HME (Medisize-Dräger); Clear-Therm+HMEF (Intersurgical). Humidification parameters (loss of water weight, average absolute moisture [AAM], absolute variation of moisture) have been evaluated on a bench-test in conformity with the ISO 9360: 2000 standard, for 24h with the following ventilatory settings: tidal volume at 500 ml, respiratory rate at 15 c/min, and inspiration/expiration ratio at 1:1. The flow resistance of HMEFs assessed using the pressure drop method was measured before and after 24h of humidification for three increasing air flows of 30, 60, and 90 l/min. All the HMEFs allowed satisfactory level of humidification exceeding 30 mgH(2)O/l. The less powerful remained the Clear-Therm. Concerning HMEFs flow resistance, results showed a pressure drop slightly more important for the Hygrobac S filter as compared with other filters. This test showed differences between the HMEFs for both humidification and resistance parameters. When compared to the new version of the standards, HMEFs demonstrated their reliability. However, evolution of humidification and flow resistance characteristics over 24h showed a structural degradation of HMEFs, limiting their use over a longer period.

Secondary Containers and Service Containers for Pesticides

Science.gov (United States)

Secondary containers and service containers are used by pesticide applicators in the process of applying a pesticide. EPA does not require secondary containers or service containers to be labeled or to meet particular construction standards. Learn more.

30 CFR 56.6312 - Secondary blasting.

Science.gov (United States)

2010-07-01

... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Explosives Use § 56.6312 Secondary blasting. Secondary blasts fired at the same time in the same work area shall be initiated from...

Numerical Study of Condensation Heat Exchanger Design in a Subcooled Pool: Correlation Investigation

International Nuclear Information System (INIS)

Lee, Hee Joon; Ju, Yun Jae; Kang, Han Ok; Lee, Tae Ho; Park, Cheon Tae

2012-01-01

Generally the condensation heat exchanger has higher heat transfer coefficient compared to the single phase heat exchanger, so has been widely applied to the cooling systems of energy plant. Recently vertical or horizontal type condensation heat exchangers are being studied for the application to secondary passive cooling system of nuclear plants. Lee and Lee investigated the existing condensation correlation to the experiment for heat exchanger in saturated pool. They concluded Traviss' correlation showed most satisfactory results for the heat transfer coefficient and mass flow rate in a saturated water pool. In this study, a thermal sizing program of vertical condensation heat exchanger to design, TSCON(Thermal Sizing of CONdenser) was validated with the existing experimental data of condensation heat exchanger in a subcooled pool for pure steam condensation

Developing mixed convection in a coiled heat exchanger

NARCIS (Netherlands)

Sillekens, J.J.M.; Rindt, C.C.M.; Steenhoven, van A.A.

1998-01-01

In this paper the development of mixed convection in a helically coiled heat exchanger for Re = 500, Pr = 5 and
δ =114
is studied. The influence of buoyancy forces ¢
(Gr = ¢O (105))
on heat transfer and secondary flow is analyzed. In the method used the parabolized equations are

Ideas Exchange: What Is the Role of Dance in the Secondary Physical Education Program?

Science.gov (United States)

Lorenzi, David G. (Comp.)

2010-01-01

This article presents ideas and views of educators regarding the role of dance in the secondary physical education program. One educator believes that dance education is an excellent complement to the traditional physical education program at the secondary level. Another educator defines physical education as the "art and science of human…

77 FR 48576 - Self-Regulatory Organizations; BATS Exchange, Inc.; Notice of Filing and Immediate Effectiveness...

Science.gov (United States)

2012-08-14

... and will become operative on August 1, 2012. (ii) Physical Ports to Secondary Data Center The Exchange currently charges for both ``logical'' ports used for order entry or receipt of Exchange data, and... application, such as FIX order entry or PITCH data receipt. In contrast, a physical port is the port that is...

78 FR 41453 - Self-Regulatory Organizations; BATS Exchange, Inc.; Notice of Filing and Immediate Effectiveness...

Science.gov (United States)

2013-07-10

... Port, each of which are logical ports \\6\\ used to receive data from the Exchange.\\7\\ Currently, the... receipt. Logical port fees are limited to logical ports in the Exchange's primary data center and no logical port fees are assessed for redundant secondary data center ports. \\7\\ BATS FIX ports are the only...

A Range-Based Multivariate Model for Exchange Rate Volatility

OpenAIRE

Tims, Ben; Mahieu, Ronald

2003-01-01

textabstractIn this paper we present a parsimonious multivariate model for exchange rate volatilities based on logarithmic high-low ranges of daily exchange rates. The multivariate stochastic volatility model divides the log range of each exchange rate into two independent latent factors, which are interpreted as the underlying currency specific components. Due to the normality of logarithmic volatilities the model can be estimated conveniently with standard Kalman filter techniques. Our resu...

Concept for a primary Romanian radon standard

International Nuclear Information System (INIS)

Sahagia, M.; Stanga, D.; Waetjen, A.C.; Luca, A.; Toro, L.; Varlam, C.; Cassette, P.

2008-01-01

The paper presents the concept of a complex system, aimed to assure the traceability of 222 Rn measurements, from the absolute (primary) standardization to the preparation and delivery of secondary standards, gas vials. The system will contain a solid 226 Ra source, a gas radon circuit, connections with a liquid scintillator vial and with glass vials. The absolute standardization of the 222 Rn, in equilibrium with all the short half life daughters, will be performed by the method of the Liquid Scintillation Counting (LSC). The system, and method, will allow our laboratory to take part in future international 222 Rn comparisons. The transfer of activity unit from the primary to the secondary standardization will be performed by the preparation of vials with 222 Rn gas, comparative measurements by LSC and a GeHP gamma-ray spectrometry system, or a well type NaI(Tl) crystal, and their link. The secondary standards will be used for the calibration of measurement instruments, for assurance of controlled radon atmosphere in 'radon chambers', and for the validation of some calculation models for various detectors efficiency. The range of activities for secondary standards is in agreement with the national measurement necessities. (author)

Preliminary study on high temperature heat exchanger for nuclear steel making

Energy Technology Data Exchange (ETDEWEB)

Mori, Y [Tokyo Inst. of Tech. (Japan); Ikegami, H

1975-03-01

In the high temperature heat exchanger as well as the steam reformer, several technical problems should be solved before realizing a nuclear plant complex for iron and steel making. Research has been carried out on heat exchanger between helium and steam, hydrogen permeation through super alloys, hydrogen removal using a titanium sponge, and creep and carburization performance of super alloys. The primary coolant used is helium having a pressure of approximately 12 kg/cm/sup 2/G and a temperature of approximately 1100/sup 0/C measured at the inlet of the high temperature heat exchanger, i.e., the test section. Steam, hydrogen and carbon monoxide are used as secondary coolants.

Construction and performance testing of a secondary cooling system with hydrogen gas (I)

International Nuclear Information System (INIS)

Hishida, M.; Nekoya, S.; Takizuka, T.; Emori, K.; Ogawa, M.; Ouchi, M.; Okamoto, Y.; Sanokawa, K.; Nakano, T.; Hagiwara, T.

1979-08-01

An experimental multi-purpose High-Temperature Gas Cooled Reactor (VHTR) which is supposed to be used for a direct steel-making is now being developed in JAeRI. In order to simulate the heat exchanging system between the primary helium gas and the secondary reducing gas system of VHTR, a hydrogen gas loop was constructed as a secondary cooling system of the helium gas loop. The maximum temperature and the maximum pressure of the hydrogen gas are 900 degrees C and 42 kg/cm 2 x G respectively. The construction of the hydrogen gas loop was completed in January, 1977, and was successfully operated for 1.000 h. Various performance tests, such as the hydrogen permeation test of a He/H2 heat exchanger and the thermal performance test of heat exchangers, were made. Especially, it was proved that hydrogen permeation rate through the heat exchanger was reduced to 1/30 to approximately 1/50 by a method of calorized coating, and the coating was stable during 1.000 h's operation. It was also stable against the temperature changes. This report describes the outline of the facility and performance of the components. (orig.) [de

Custom, contract, and kidney exchange.

Science.gov (United States)

Healy, Kieran; Krawiec, Kimberly D

2012-01-01

In this Essay, we examine a case in which the organizational and logistical demands of a novel form of organ exchange (the nonsimultaneous, extended, altruistic donor (NEAD) chain) do not map cleanly onto standard cultural schemas for either market or gift exchange, resulting in sociological ambiguity and legal uncertainty. In some ways, a NEAD chain resembles a form of generalized exchange, an ancient and widespread instance of the norm of reciprocity that can be thought of simply as the obligation to “pay it forward” rather than the obligation to reciprocate directly with the original giver. At the same time, a NEAD chain resembles a string of promises and commitments to deliver something in exchange for some valuable consideration--that is, a series of contracts. Neither of these salient "social imaginaries" of exchange--gift giving or formal contract--perfectly meets the practical demands of the NEAD system. As a result, neither contract nor generalized exchange drives the practice of NEAD chains. Rather, the majority of actual exchanges still resemble a simpler form of exchange: direct, simultaneous exchange between parties with no time delay or opportunity to back out. If NEAD chains are to reach their full promise for large-scale, nonsimultaneous organ transfer, legal uncertainties and sociological ambiguities must be finessed, both in the practices of the coordinating agencies and in the minds of NEAD-chain participants. This might happen either through the further elaboration of gift-like language and practices, or through a creative use of the cultural form and motivational vocabulary, but not necessarily the legal and institutional machinery, of contract.

Leak detection for heat exchangers in nuclear facilities

International Nuclear Information System (INIS)

Tsu, D.

1979-01-01

There is added to the secondary circuit 40 Ar, which can be activated. If the heat exchanger to the primary circuit has got a leak 40 Ar will enter the latter and is coverted into 40 Ar in the core of the He-cooled pebble-bed reactor. The gamma activity of 41 Ar is then determined. (DG) [de

DEVELOPMENT PERSPECTIVES OF SECURITIES SECONDARY MARKET IN REPUBLIC OF MOLDOVA

Directory of Open Access Journals (Sweden)

Chetraru Aliona

2012-07-01

Full Text Available It’s an urgent necessity to determine the specific problems of the securities market in Republic of Moldova, in the context of policies and strategies of accession to the European and International activity standards, performance and quality, along with the implication and effects of the international financial crisis. Identification of the influence factors with negative on the secondary market will enable the formulation of recommendations, proposals, improvement and refreshing techniques for the capital market as a whole. The analysis of the secondary market indicators allowed concluding on a high degree of uncertainty and predictability of its evolution. Legislative and regulatory issues on the securities secondary market activity of professional participants, admit the interpretation duality of provisions concerned. National Commission of Financial Market activity as a mega-regulator of the financial market, although involving a increased complexity of activities concerning supervision, control and regulation of the financial (non-banking sector, do not enjoy great efficiency in terms of stabilization and promotion of the financial sector. The appearance of a stock institution as an alternative to the existing one, after 20 years of experience of the latter, theoretically opens new market opportunities, although in practical terms, at this moment of time, the market participants are reserved and undecided on the future development trend of the secondary market. The study is based on statistical data contained in annual reports of the National Financial Market Commission and published on the official website of JSC „Stock Exchange of Moldova”, analysis of legislative and regulatory provisions and international practices. The statistics cover the whole period of operation of the secondary market in Republic of Moldova, that is from 1995 to 2012, as much as the stock market segment and the counter. The research methodology

Thermo-economic optimization of secondary distribution network of low temperature district heating network under local conditions of South Korea

DEFF Research Database (Denmark)

Park, Byung Sik; Imran, Muhammad; Hoon, Im-Yong

2017-01-01

. The corresponding heat loss from secondary network, pumping power and area of domestic hot water heat exchanger unit for each supply temperature and temperature difference for required heating load of the apartment complex are calculated. Results indicate that when supply temperature is decreased from 65 °C to 45...... apartment. The Apartment complex has 15 floors, 4 apartments on each floor and each apartment has heating surface area of 85 m2. The supply temperature of the hot water is reduced from 65 °C to 45 °C and the temperature difference between supply and return line is varied from 18 °C to 27 °C...... °C, area of heat exchanger is increased by 68.2%, pumping power is also increased by 9.8% and heat loss is reduced by 15.6%. These results correspond to a temperature difference of 20 °C, the standard temperature difference in South Korea residential heating system. Economic assessment...

Heat pipes in modern heat exchangers

International Nuclear Information System (INIS)

Vasiliev, Leonard L.

2005-01-01

Heat pipes are very flexible systems with regard to effective thermal control. They can easily be implemented as heat exchangers inside sorption and vapour-compression heat pumps, refrigerators and other types of heat transfer devices. Their heat transfer coefficient in the evaporator and condenser zones is 10 3 -10 5 W/m 2 K, heat pipe thermal resistance is 0.01-0.03 K/W, therefore leading to smaller area and mass of heat exchangers. Miniature and micro heat pipes are welcomed for electronic components cooling and space two-phase thermal control systems. Loop heat pipes, pulsating heat pipes and sorption heat pipes are the novelty for modern heat exchangers. Heat pipe air preheaters are used in thermal power plants to preheat the secondary-primary air required for combustion of fuel in the boiler using the energy available in exhaust gases. Heat pipe solar collectors are promising for domestic use. This paper reviews mainly heat pipe developments in the Former Soviet Union Countries. Some new results obtained in USA and Europe are also included

Financial and fiscal crises, prices and EUR/USD rate of exchange

Directory of Open Access Journals (Sweden)

Slawomir I. Bukowski

2017-09-01

Full Text Available Purpose: The purpose of this paper is to answer the following question: How did the standard and non-standard ECB policy measures influence the price level and the EUR/USD rate of exchange in the period 2008 -2013? Design/methodology/approach: We formulated the following hypothesis: Depreciation of the Euro versus American dollar exchange rate occurred in the period of financial and fiscal crisis (2008-2014. The main reasons for that included: fiscal crisis in the euro area, implementation of standard and non–standard (quantitative easing ECB monetary policy measures and growth of money supply in the euro area. In that period, the economically and statistically significant impacts of money supply aggregate M2 and differences between interest rates and rates of inflation in the euro area and USA on changes in EUR/USD rate of exchange were noted. For verification of our hypothesis we used econometric modeling - model of regression estimated using the GARCH (0.1, using the monthly data for the period 1999:01-2013:12. Results of our research confirmed the hypothesis formulated by us. Findings: Our study confirmed the formulated hypothesis; the EBC monetary policy, both standard and non-standard, in the years 2008-2014 had a significant effect on the EUR/USD exchange rate, contributing largely to the depreciation of the euro in the same period. Research limitations/implications: The same method of research could be applied to other cases of currency area and central bank monetary policy. Originality/value: The results support the existence of statistically and economically significant impact of central bank policy on the rate of exchange, by the expansion of money supply, changes of differences between interest rates and rates of inflation inside and outside the currency rate area. Those results confirm conclusion formulated based on the theory of interest rate parity and assets theory of currency rates.

78 FR 19350 - Self-Regulatory Organizations; BATS Exchange, Inc.; Notice of Filing and Immediate Effectiveness...

Science.gov (United States)

2013-03-29

... physical ports free of charge at the primary data center and charges $2,500 per month for each additional single physical port at such data center. Separately, the Exchange charges $1,000 for each 1G physical port at the secondary data center. The Exchange proposes to normalize its 1G physical port fee at $1...

Plasma exchange for Guillain-Barré syndrome.

Science.gov (United States)

Raphaël, J C; Chevret, S; Hughes, R A; Annane, D

2002-01-01

Guillain-Barré syndrome is an acute symmetric, usually ascending and usually paralysing illness, due to inflammation of peripheral nerves. It is thought to be caused by autoimmune factors, such as antibodies. Plasma exchange removes antibodies and other potentially injurious factors from the blood stream. It involves connecting the patient's blood circulation to a machine which exchanges the plasma for a substitute solution, usually albumin. Several studies have evaluated plasma exchange for Guillain-Barré syndrome. To systematically review the evidence concerning the efficacy of plasma exchange for treating Guillain-Barré syndrome. Search of the Cochrane Neuromuscular Disease Trial Register for randomised trials concerning plasma exchange in Guillain-Barré syndrome, search of the bibliographies of identified papers and enquiry from the authors of the papers. Randomised and quasi-randomised trials of plasma exchange versus sham exchange or supportive treatment. Potentially relevant papers were scrutinised by two reviewers and the selection of eligible studies was agreed by them and a third reviewer. Data were extracted by one reviewer and checked by a second reviewer. Some missing data were obtained from the authors of studies. Six eligible trials concerning 649 patients were identified, all comparing plasma exchange versus supportive treatment alone. Primary outcome measures ~bullet~Time to recover walking with aid In the only two trials for which this measure was reported, the median time to recover this ability was faster in the plasma exchange than the control group. ~bullet~Time to onset of motor recovery in mildly affected patients In the one trial for which this measure was available, the time was significantly shortened in the plasma exchange group. Secondary outcome measures ~bullet~Improvement in disability grade at four weeks In five trials, there were significantly more patients who had improved by one disability grade or more in the plasma exchange

Beverages and snacks available in vending machines from a subset of Ontario secondary schools: Do offerings align with provincial nutrition standards?

Science.gov (United States)

Orava, Taryn; Manske, Steve; Hanning, Rhona

2016-12-27

As part of an evaluation of Ontario's School Food and Beverage Policy (P/PM 150) in a populous Ontario region, this research aimed to: 1) identify, describe and categorize beverages and snacks available for purchase in secondary school vending machines according to P/PM 150 standards; and 2) compare the number and percentage of beverages and snacks within P/PM 150 categories (Sell Most, Sell Less, Not Permitted) from Time I (2012/2013) to Time II (2014). Representatives from consenting secondary schools assisted researchers in completing a Food Environmental Scan checklist in Times I and II. Sourced nutritional content information (calories, fats, sodium, sugars, ingredients and % daily values) was used to categorize products. The number and percentage of products in P/PM 150 categories were compared between Times by paired t-tests. Of 26 secondary schools participating in total, 19 participated in both Time periods and were included in the study. There were 75 beverages identified (59 Time I, 45 Time II), mostly water, juices and milk-based beverages; and 132 types of snacks (87 Time I, 103 Time II), mostly grain-based snacks, vegetable/fruit chips, and baked goods. A majority of schools offered one or more Not Permitted beverages (47% Time I, 58% Time II) or snacks (74% Time I, 53% Time II). Significantly more schools met P/PM 150 standards for snacks (p = 0.02) but not beverages in Time II. Full P/PM 150 compliance was achieved by few schools, indicating that schools, school boards, public health, and food services need to continue to collaborate to ensure nutrient-poor products are not sold to students in school settings.

Chapter 11. Heat Exchangers

Energy Technology Data Exchange (ETDEWEB)

Rafferty, Kevin D.; Culver, Gene

1998-01-01

Most geothermal fluids, because of their elevated temperature, contain a variety of dissolved chemicals. These chemicals are frequently corrosive toward standard materials of construction. As a result, it is advisable in most cases to isolate the geothermal fluid from the process to which heat is being transferred. The task of heat transfer from the geothermal fluid to a closed process loop is most often handled by a plate heat exchanger. The two most common types used in geothermal applications are: bolted and brazed. For smaller systems, in geothermal resource areas of a specific character, downhole heat exchangers (DHEs) provide a unique means of heat extraction. These devices eliminate the requirement for physical removal of fluid from the well. For this reason, DHE-based systems avoid entirely the environmental and practical problems associated with fluid disposal. Shell and tube heat exchangers play only a minor role in low-temperature, direct-use systems. These units have been in common use in industrial applications for many years and, as a result, are well understood. For these reasons, shell and tube heat exchangers will not be covered in this chapter.

Developing the Conflicts Management Model for School Administrators of Secondary School under the Office of Secondary Educational Service Area 20

Directory of Open Access Journals (Sweden)

Pornpan Ruangrit

2017-09-01

Full Text Available This study aimed to 1 investigate the cause of conflict which in the secondary schools under the Secondary School under the Office of Secondary Educational Service Area 20, 2 study the conflict management method which administrators applied in Secondary School under the Office of Secondary Educational Service Area 20, and 3 develop conflict management model for Secondary School under the Office of Secondary Educational Service Area 20. The participants were 115 school administrators (44 school directors and 71 deputy directors which were selected by random sampling technique. The research instruments included a questionnaire, which reliability value was 0.97, and an interview schedule that were administered to the respondents. The data were analyzed by frequency, percentage, mean, and standard deviation. The result of the study showed that: 1. the causes of conflict in Secondary School under the Office of Secondary Educational Service Area 20 in overall was at the high level with the mean of 4.21, the internal conflict was at the high level with the mean of 4.22, and the external conflict was at the high level with the mean of 4.19. 2. Overall, conflict management method used by administrators in Secondary School under the Office of Secondary Educational Service Area 20was at a high level. Considering each aspect, the compromising method was the highest level at 4.48. 3. Developing conflict management model in Secondary School under the Office of Secondary Educational Service Area 20 were the collaboration and making understand method. These should be used for conflict management to achieve the success and to reach the standard which including responsibility, accountability, equality, teamwork, and communication competence.

An Econometric Diffusion Model of Exchange Rate Movements within a Band - Implications for Interest Rate Differential and Credibility of Exchange Rate Policy

OpenAIRE

Rantala, Olavi

1992-01-01

The paper presents a model ofexchange rate movements within a specified exchange rate band enforced by central bank interventions. The model is based on the empirical observation that the exchange rate has usually been strictly inside the band, at least in Finland. In this model the distribution of the exchange rate is truncated lognormal from the edges towards the center of the band and hence quite different from the bimodal distribution of the standard target zone model. The model is estima...

Plate heat exchanger - inertia flywheel performance in loss of flow transient

International Nuclear Information System (INIS)

Abou-El-Maaty, Talal; Abd-El-Hady, Amr

2009-01-01

One of the most versatile types of heat exchangers used is the plate heat exchanger. It has principal advantages over other heat exchangers in that plates can be added and/or removed easily in order to change the area available for heat transfer and therefore its overall performance. The cooling systems of Egypt's second research reactor (ETRR 2) use this type of heat exchanger for cooling purposes in its primary core cooling and pool cooling systems. In addition to the change in the number of heat exchanger cooling channels, the effect of changing the amount of mass flow rate on the heat exchanger performance is an important issues in this study. The inertia flywheel mounted on the primary core cooling system pump with the plate heat exchanger plays an important role in the case of loss of flow transients. The PARET code is used to simulate the effect of loss of flow transients on the reactor core. Hence, the core outlet temperature with the pump-flywheel flow coast down is fed into the plate heat exchanger model developed to estimate the total energy transferred to the cooling tower, the primary side heat exchanger temperature variation, the transmitted heat exchanger power, and the heat exchanger effectiveness. In addition, the pressure drop in both, the primary side and secondary side of the plate heat exchanger is calculated in all simulated transients because their values have limits beyond which the heat exchanger is useless. (orig.)

ESPA Based Secondary Payload Orbit Maneuvering System, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Busek Co. Inc. proposes to develop/design an integrated propulsion, power, ACS, and separation module for secondary ESPA payloads. The standardized secondary payload...

Automatic Generation of Object Models for Process Planning and Control Purposes using an International standard for Information Exchange

Directory of Open Access Journals (Sweden)

Petter Falkman

2003-10-01

Full Text Available In this paper a formal mapping between static information models and dynamic models is presented. The static information models are given according to an international standard for product, process and resource information exchange, (ISO 10303-214. The dynamic models are described as Discrete Event Systems. The product, process and resource information is automatically converted into product routes and used for simulation, controller synthesis and verification. A high level language, combining Petri nets and process algebra, is presented and used for speci- fication of desired routes. A main implication of the presented method is that it enables the reuse of process information when creating dynamic models for process control. This method also enables simulation and verification to be conducted early in the development chain.

77 FR 3590 - Covered Securities of Bats Exchange, Inc.

Science.gov (United States)

2012-01-25

... firms' incentives to list with one exchange versus another). \\78\\ It has been noted that NYSE and the...: A Theory of Cross-Listing and Endogenous Listing Standards, 82 J. Fin. Econ. 455, 456 (2006). See... exchanges (in terms of listings) will tend to be favored over smaller ones. In theory, this preference may...

8 CFR 214.12 - Preliminary enrollment of schools in the Student and Exchange Visitor Information System (SEVIS).

Science.gov (United States)

2010-01-01

... of schools in the Student and Exchange Visitor Information System (SEVIS). (a) Private elementary and private secondary schools, public high schools, post-secondary schools, language schools, and vocational... 8 Aliens and Nationality 1 2010-01-01 2010-01-01 false Preliminary enrollment of schools in the...

Rapid and accurate processing method for amide proton exchange rate measurement in proteins

International Nuclear Information System (INIS)

Koskela, Harri; Heikkinen, Outi; Kilpelaeinen, Ilkka; Heikkinen, Sami

2007-01-01

Exchange between protein backbone amide hydrogen and water gives relevant information about solvent accessibility and protein secondary structure stability. NMR spectroscopy provides a convenient tool to study these dynamic processes with saturation transfer experiments. Processing of this type of NMR spectra has traditionally required peak integration followed by exponential fitting, which can be tedious with large data sets. We propose here a computer-aided method that applies inverse Laplace transform in the exchange rate measurement. With this approach, the determination of exchange rates can be automated, and reliable results can be acquired rapidly without a need for manual processing

78 FR 58359 - Self-Regulatory Organizations; Topaz Exchange, LLC; Notice of Filing and Immediate Effectiveness...

Science.gov (United States)

2013-09-23

... Exchange, therefore, opted to provide a higher introductory rate for Maker Rebates in order to attract... rate of fees and rebates the Exchange currently provides for trading in Standard Options. The Exchange... order flow to another exchange if they deem rebates at a particular exchange to be too low. For the...

Uncertainty analysis for secondary energy distributions

International Nuclear Information System (INIS)

Gerstl, S.A.W.

1978-01-01

In many transport calculations the integral design parameter of interest (response) is determined mainly by secondary particles such as gamma rays from (n,γ) reactions or secondary neutrons from inelastic scattering events or (n,2n) reactions. Standard sensitivity analysis usually allows to calculate the sensitivities to the production cross sections of such secondaries, but an extended formalism is needed to also obtain the sensitivities to the energy distribution of the generated secondary particles. For a 30-group standard cross-section set 84% of all non-zero table positions pertain to the description of secondary energy distributions (SED's) and only 16% to the actual reaction cross sections. Therefore, any sensitivity/uncertainty analysis which does not consider the effects of SED's is incomplete and neglects most of the input data. This paper describes the methods of how sensitivity profiles for SED's are obtained and used to estimate the uncertainty of an integral response due to uncertainties in these SED's. The detailed theory is documented elsewhere and implemented in the LASL sensitivity code SENSIT. SED sensitivity profiles have proven particularly valuable in cross-section uncertainty analyses for fusion reactors. Even when the production cross sections for secondary neutrons were assumed to be without error, the uncertainties in the energy distribution of these secondaries produced appreciable uncertainties in the calculated tritium breeding rate. However, complete error files for SED's are presently nonexistent. Therefore, methods will be described that allow rough error estimates due to estimated SED uncertainties based on integral SED sensitivities

Heat exchanger with oscillating flow

Science.gov (United States)

Scotti, Stephen J. (Inventor); Blosser, Max L. (Inventor); Camarda, Charles J. (Inventor)

1993-01-01

Various heat exchange apparatuses are described in which an oscillating flow of primary coolant is used to dissipate an incident heat flux. The oscillating flow may be imparted by a reciprocating piston, a double action twin reciprocating piston, fluidic oscillators or electromagnetic pumps. The oscillating fluid flows through at least one conduit in either an open loop or a closed loop. A secondary flow of coolant may be used to flow over the outer walls of at least one conduit to remove heat transferred from the primary coolant to the walls of the conduit.

Demarcation of secondary hyperalgesia zones

DEFF Research Database (Denmark)

Ringsted, Thomas K; Enghuus, Casper; Petersen, Morten A

2015-01-01

of analgesic drug effects in humans. However, since the methods applied in demarcating the secondary hyperalgesia zone seem inconsistent across studies, we examined the effect of a standardized approach upon the measurement of SHA following a first degree burn injury (BI). NEW METHOD: The study was a two.......0001). No day-to-day or observer-to-observer differences in SHAs were observed. Intraclass correlation coefficients, in the range of 0.51 to 0.84, indicated a moderate to almost perfect reliability between observers. COMPARISON WITH EXISTING METHODS: No standardized approach in SHA-assessment has hitherto been...... presented. CONCLUSIONS: This is the first study to demonstrate that demarcation of secondary hyperalgesia zones depends on the developed pressure of the punctate stimulator used....

The Effect of Exchange Rate Volatility on Iran’s Raisin Export

OpenAIRE

2014-01-01

Exchange rate volatility is one of the effective and ambiguous factors in agricultural product export. Considering the importance of agricultural trade to avoid single-product economy, the main aim of this study was to investigate the impact of exchange rate volatility on the Raisin export of Iran during the years1959-2011. For this purpose, exchange rate volatility index was estimated using Moving Average Standard Deviation (MASD). Then, the impact of exchange rate volatility on the value of...

Study of the Metrological Characteristics of the FBX Dosimeter in the Photon Beam using a Secondary Standard

International Nuclear Information System (INIS)

Moussous, O.; Yahiche, K.; Medjadj, T.

2008-01-01

The metrological characteristics of the dosimetric system containing 0.20 m M ferrous ammonium sulphate, 5.0 m M benzoic acid and 0.20 m M xyelenol orange in 0.05 N sulphuric acid. (FBX dosimeter) was investigated. The wavelength and absorbance linearity calibration of the spectrophotometer were checked using NBS Standard Reference Material. The molar absorption coefficient ε of the dosimeter solution was determined using carefully prepared standard solution. The G-value for the ferric-xylenol orange complex when this dosimeter is exposed in air to gamma radiation was determined using a secondary standard (ionization chamber). The dosimetric solutions could be stored for about 2 weeks before irradiations and up to 2 days after irradiations without any significant error in dose estimations. The linearity of the absorbed dose with the increases in absorbance of the dosimeter solution has been checked. For this purpose, the dosimeter solutions were irradiated to a series of different absorbed doses (3 to 11 Gy). The quality data, as judged from the correlation coefficient, demonstrate that the curve is linear in the range investigated. The stability and reproducibility of response are such that this system should be used to measure the low doses. The reproducibility allowed us to determine the lower detection limit of the FBX dosimeter, which is around 5 Gy

Analysis of Washout Filter-Based Power Sharing Strategy—An Equivalent Secondary Controller for Islanded Microgrid without LBC Lines

DEFF Research Database (Denmark)

Han, Yang; Li, Hong; Xu, Lin

2018-01-01

As a supplement of the droop control, the concept of secondary controlled microgrid (MG) has been extensively studied for voltage and frequency restoration. However, the low band-width communication (LBC) channels are needed to exchange information between the primary and secondary controllers...

Securing the smart grid information exchange

Energy Technology Data Exchange (ETDEWEB)

Fries, Steffen; Falk, Rainer [Siemens AG, Corporate Technology, Muenchen (Germany)

2012-07-01

The smart grid is based on information exchange between various stakeholders using open communication technologies, to control the physical electric grid through the information grid. Protection against cyber attacks is essential to ensure a reliable operation of the smart grid. This challenge is addressed by various regulatory, standardization, and research activities. After giving an overview of the security demand of a smart grid, existing and appearing standardization activities are described. (orig.)

The dry heat exchanger calorimeter system

International Nuclear Information System (INIS)

Renz, D.P.; Wetzel, J.R.; James, S.J.; Kasperski, P.W.; Duff, M.F.

1991-01-01

A radiometric isothermal heat flow calorimeter and preconditioner system that uses air instead of water as the heat exchange medium has been developed at Mound. The dry heat exchanger calorimeter is 42 inches high by 18 inches in diameter and the preconditioner is a 22 inch cube, making it extremely compact compared to existing units. The new system is ideally suited for transportable, stand-alone, or glovebox applications. Preliminary tests of the system have produced sample measurements with standard deviations less than 0.25% and sample errors less than 0.50%. These tests have shown that the dry heat exchanger system will yield acceptance data with an accuracy comparable to those of Mound water bath systems now in use. 4 figs., 1 tab

Solution of operational problems utilization of an EX-IRT-2000 heat exchanger

International Nuclear Information System (INIS)

Razak, Abdu

1986-01-01

The Bandung TRIGA Mark II Reactor has been successfully operated for 21 years, especially in low power operation or as neutron sources for various experiments. Most of the operating time, approximately 80% of routine operation, was dedicated for radio-isotope production. During routine operation for radio-isotope production, the reactor could not be operated at full power. The reactor was operated at 60% of the maximum power (1 MWth) due to the inability of the original heat exchanger to operate properly. The reason is that slack deposition was built-up on the secondary side of the heat exchanger. Therefore, it reduced the coefficient of heat transfer considerably. To solve the problems, a set of heat exchanger including the pump was installed In parallel with the original unit. The heat exchanger was an IRT-2000 Reactor Heat exchanger which was collected from the abandoned IRT-2000 Project. The heat exchanger has capacity of 1.25 MW. The new heat exchanger could reduced the outlet temperature of the primary coolant Into 42 deg. C. While the original-heat exchanger at the worst condition and at 600 kW of power reach outlet temperature 49 deg. C. The IRT Heat Exchanger is a counter flow heat exchanger. (author)

Solution of operational problems utilization of an EX-IRT-2000 heat exchanger

Energy Technology Data Exchange (ETDEWEB)

Razak, Abdu [Research Centre for Nuclear Techniques, National Atomic Energy Agency (Indonesia)

1986-07-01

The Bandung TRIGA Mark II Reactor has been successfully operated for 21 years, especially in low power operation or as neutron sources for various experiments. Most of the operating time, approximately 80% of routine operation, was dedicated for radio-isotope production. During routine operation for radio-isotope production, the reactor could not be operated at full power. The reactor was operated at 60% of the maximum power (1 MWth) due to the inability of the original heat exchanger to operate properly. The reason is that slack deposition was built-up on the secondary side of the heat exchanger. Therefore, it reduced the coefficient of heat transfer considerably. To solve the problems, a set of heat exchanger including the pump was installed In parallel with the original unit. The heat exchanger was an IRT-2000 Reactor Heat exchanger which was collected from the abandoned IRT-2000 Project. The heat exchanger has capacity of 1.25 MW. The new heat exchanger could reduced the outlet temperature of the primary coolant Into 42 deg. C. While the original-heat exchanger at the worst condition and at 600 kW of power reach outlet temperature 49 deg. C. The IRT Heat Exchanger is a counter flow heat exchanger. (author)

77 FR 8928 - Self-Regulatory Organizations; EDGA Exchange, Inc.; Notice of Filing and Immediate Effectiveness...

Science.gov (United States)

2012-02-15

... is shared by NASDAQ and the following SROs: Boston Options Exchange, C2 Options Exchange... Exchange's responsibility to prescribe standards of training, experience, and competence for Exchange... levels of competence and knowledge generally applicable to proprietary trading. \\16\\ 15 U.S.C. 78f(b...

Arrangement between the US Nuclear Regulatory Commission (USNRC) and the Belgian Government for Exchange of Technical Information in Regulatory Matters and in Cooperation in Safety Research and in Standards Development

International Nuclear Information System (INIS)

1978-01-01

This Arrangement was concluded on 6 June 1978 between the United States Nuclear Regulatory Commission and the Belgian Government for exchange of technical information in regulatory matters and in co-operation in safety research and in standards development. Both Parties agree to exchange, as available, technical information related to the regulation of safety and the environmental impact of designated nuclear energy facilities and to safety research of designated types of nuclear facilities. As regards co-operation in safety research, the execution of joint programmes and projects under which activities are divided between the two Parties will be agreed on a case by case basis. The Parties further agree to co-operate in the development of regulatory standards applicable to the designated nuclear facilities. The Arrangement is valid for 5 years and may be extended. (NEA) [fr

Secondary abdominal appendicular ectopic pregnancy.

Science.gov (United States)

Nama, Vivek; Gyampoh, Bright; Karoshi, Mahantesh; McRae, Reynold; Opemuyi, Isaac

2007-01-01

Although the case fatality rate for ectopic pregnancies has decreased to 0.08% in industrialized countries, it still represents 3.8% of maternal mortality in the United States alone. In developing countries, the case fatality rate varies from 3% to 27%. Laparoscopic management of tubal pregnancies is now the standard form of treatment where this technology is available. Abdominal pregnancies are rare, and secondary implantation of tubal ectopic pregnancies is the most common cause of abdominal gestations. We present an interesting case of secondary implantation of a tubal ectopic pregnancy to highlight the appendix as a possible secondary implantation site after a tubal ectopic pregnancy.

A cross-country Exchange Market Pressure (EMP dataset

Directory of Open Access Journals (Sweden)

Mohit Desai

2017-06-01

Full Text Available The data presented in this article are related to the research article titled - “An exchange market pressure measure for cross country analysis” (Patnaik et al. [1]. In this article, we present the dataset for Exchange Market Pressure values (EMP for 139 countries along with their conversion factors, ρ (rho. Exchange Market Pressure, expressed in percentage change in exchange rate, measures the change in exchange rate that would have taken place had the central bank not intervened. The conversion factor ρ can interpreted as the change in exchange rate associated with $1 billion of intervention. Estimates of conversion factor ρ allow us to calculate a monthly time series of EMP for 139 countries. Additionally, the dataset contains the 68% confidence interval (high and low values for the point estimates of ρ’s. Using the standard errors of estimates of ρ’s, we obtain one sigma intervals around mean estimates of EMP values. These values are also reported in the dataset.

A cross-country Exchange Market Pressure (EMP) dataset.

Science.gov (United States)

Desai, Mohit; Patnaik, Ila; Felman, Joshua; Shah, Ajay

2017-06-01

The data presented in this article are related to the research article titled - "An exchange market pressure measure for cross country analysis" (Patnaik et al. [1]). In this article, we present the dataset for Exchange Market Pressure values (EMP) for 139 countries along with their conversion factors, ρ (rho). Exchange Market Pressure, expressed in percentage change in exchange rate, measures the change in exchange rate that would have taken place had the central bank not intervened. The conversion factor ρ can interpreted as the change in exchange rate associated with $1 billion of intervention. Estimates of conversion factor ρ allow us to calculate a monthly time series of EMP for 139 countries. Additionally, the dataset contains the 68% confidence interval (high and low values) for the point estimates of ρ 's. Using the standard errors of estimates of ρ 's, we obtain one sigma intervals around mean estimates of EMP values. These values are also reported in the dataset.

Beyond the exchange--the future of B2B.

Science.gov (United States)

Wise, R; Morrison, D

2000-01-01

Using the Internet to facilitate business-to-business commerce promises many benefits, such as dramatic cost reductions and greater access to buyers and sellers. Yet little is known about how B2B e-commerce will evolve. The authors argue that changes in the financial services industry over the past two decades provide important clues. Exchanges, they say, are not the primary source of value in information-intensive markets; value tends to accumulate among a diverse group of specialists that focus on such tasks as packaging, standard setting, arbitrage, and information management. Because scale and liquidity are vitally important to efficient trading, today's exchanges will consolidate into a relatively small set of mega-exchanges. Originators will handle the origination and aggregation of complex transactions before sending them on to mega-exchanges for execution. E-speculators, seeking to capitalize on an abundance of market information, will tend to concentrate where relatively standardized products can be transferred easily among a large group of buyers. In many markets, a handful of independent solution providers with well-known brand names and solid reputations will thrive alongside mega-exchanges. Sell-side asset exchanges will create the networks and provide the tools to allow suppliers to trade orders among themselves, sometimes after initial transactions with customers are made on the mega-exchanges. For many companies, traditional skills in such areas as product development, manufacturing, and marketing may become relatively less important, while the ability to understand and capitalize on market dynamics may become considerably more important.

Radioanalytical determination of plutonium and americium using ion exchange and extraction chromatography technique in urine

International Nuclear Information System (INIS)

Santhanakrishnan, V.; Sreedevi, K.R.; Rajaram, S.; Ravi, P.M.

2011-01-01

The use of anion exchange chromatography for the separation of Pu and extraction chromatography technique for the separation of Am from urine samples was studied. In the earlier method, Pu separation was carried out by anion exchange chromatography followed by Am separation by cation exchange chromatography. The chemical recovery of Am obtained by cation exchange separation method was inconsistent and low in the range 30-70%. In this study, the average Pu recovery obtained using anion exchange chromatography was 89.2 with standard deviation of 10.4 and the average Am recovery obtained using extraction chromatography with TRU resin was 77.4 with standard deviation of 14.8. Moreover, Am separation could be completed within three hours using the TRU column compared to two days that were required for the cation exchange chromatography. (author)

78 FR 77178 - Self-Regulatory Organizations; International Securities Exchange, LLC; Notice of Filing and...

Science.gov (United States)

2013-12-20

... Members that achieve Tier 2 or higher as shown in the table below. \\4\\ The Exchange offers a rebate in... higher as shown in the table below. \\5\\ The Exchange offers a rebate in Standard and Mini Options for... orders, which are similar to the Exchange's taker rates described above. The Exchange is proposing to...

ENSURING THERMAL REGIME FOR THE SUPPLY DISTRIBUTED DEVICES IN THE COMPOSITION OF THE SHIP'S SECONDARY POWER SUPPLY SYSTEMS ON THE BASE OF THE STANDARDIZED UNITS

Directory of Open Access Journals (Sweden)

T. A. Ismailov

2016-01-01

Full Text Available Aim. The article deals with the problem of constructing the power supply devices in the composition of the ship's secondary power systems based on standardized blocks and securing their thermal regime.Methods. It is stated that with the advent of modern power electronics multifunctional components the secondary power supply developers got possibilities to improve the quality of secondary power supply and to upgrade the existing systems.Results. The advantages of unified power units, having a function of parallel operation are revealed. Heat transfer processes in a vertical channel with free convection, and the calculation of the minimum width of the channel, which provides efficient heat removal have been analyzed.Conclusion.A model is proposed for determining the minimum distance between the blocks without deterioration of heat transfer in the channel formed by the walls of adjacent blocks.

Meningococcal X polysaccharide quantification by high-performance anion-exchange chromatography using synthetic N-acetylglucosamine-4-phosphate as standard.

Science.gov (United States)

Micoli, F; Adamo, R; Proietti, D; Gavini, M; Romano, M R; MacLennan, C A; Costantino, P; Berti, F

2013-11-15

A method for meningococcal X (MenX) polysaccharide quantification by high-performance anion-exchange chromatography with pulsed amperometric detection (HPAEC-PAD) is described. The polysaccharide is hydrolyzed by strong acidic treatment, and the peak of glucosamine-4-phosphate (4P-GlcN) is detected and measured after chromatography. In the selected conditions of hydrolysis, 4P-GlcN is the prevalent species formed, with GlcN detected for less than 5% in moles. As standard for the analysis, the monomeric unit of MenX polysaccharide, N-acetylglucosamine-4-phosphate (4P-GlcNAc), was used. This method for MenX quantification is highly selective and sensitive, and it constitutes an important analytical tool for the development of a conjugate vaccine against MenX. Copyright © 2013 Elsevier Inc. All rights reserved.

Measurement uncertainty. A practical guide for Secondary Standards Dosimetry Laboratories

International Nuclear Information System (INIS)

2008-05-01

The need for international traceability for radiation dose measurements has been understood since the early nineteen-sixties. The benefits of high dosimetric accuracy were recognized, particularly in radiotherapy, where the outcome of treatments is dependent on the radiation dose delivered to patients. When considering radiation protection dosimetry, the uncertainty may be greater than for therapy, but proper traceability of the measurements is no less important. To ensure harmonization and consistency in radiation measurements, the International Atomic Energy Agency (IAEA) and the World Health Organization (WHO) created a Network of Secondary Standards Dosimetry Laboratories (SSDLs) in 1976. An SSDL is a laboratory that has been designated by the competent national authorities to undertake the duty of providing the necessary link in the traceability chain of radiation dosimetry to the international measurement system (SI, for Systeme International) for radiation metrology users. The role of the SSDLs is crucial in providing traceable calibrations; they disseminate calibrations at specific radiation qualities appropriate for the use of radiation measuring instruments. Historically, although the first SSDLs were established mainly to provide radiotherapy level calibrations, the scope of their work has expanded over the years. Today, many SSDLs provide traceability for radiation protection measurements and diagnostic radiology in addition to radiotherapy. Some SSDLs, with the appropriate facilities and expertise, also conduct quality audits of the clinical use of the calibrated dosimeters - for example, by providing postal dosimeters for dose comparisons for medical institutions or on-site dosimetry audits with an ion chamber and other appropriate equipment. The requirements for traceable and reliable calibrations are becoming more important. For example, for international trade where radiation products are manufactured within strict quality control systems, it is

Sevoflurane improves gaseous exchange and exerts protective ...

African Journals Online (AJOL)

Sevoflurane improves gaseous exchange and exerts protective effects in ... Lung water content and cell count were estimated by standard protocols. ... It reversed LPS-induced oxidative stress, as demonstrated by increase in total antioxidant ...

40 CFR 421.200 - Applicability: Description of the secondary mercury subcategory.

Science.gov (United States)

2010-07-01

... secondary mercury subcategory. 421.200 Section 421.200 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Mercury Subcategory § 421.200 Applicability: Description of the secondary mercury...

Calorimetry exchange program annual data report for 1992

International Nuclear Information System (INIS)

Barnett, T.M.

1992-01-01

The goals of the Calorimetry Sample Exchange Program are: discuss measurement differences; review and improve analytical measurements and methods; discuss new measurement capabilities; provide data to DOE on measurement capabilities to evaluate shipper-receiver differences; provide characterized or standard materials as necessary for exchange participants; and provide a measurement control program for plutonium analysis. A sample of PuO 2 powder is available at each participating site for NDA measurement, including either or both calorimetry and high-resolution gamma-ray spectroscopy, the elements which are typically combined to provide a calorimetric assay of plutonium. The facilities measure the sample as frequently and to the level of precision which they desire, and then submit the data to the Exchange for analysis. The data report includes summary tables for each measurement and charts showing the performance of each laboratory. Comparisons are made to the accepted values for the exchange sample and to data previously reported by that laboratory. This information is presented, in the form of quarterly and annual reports, intended for use by Exchange participants in measurement control programs, or to indicate when bias corrections may be appropriate. No attempt, however, has been made to standardize methods or frequency of data collection, calibration, or operating procedures. Direct comparisons between laboratories may, therefore, be misleading since data have not been collected to the same precision or for the same time periods. A meeting of the participants of the Calorimetry Exchange is held annually at EG ampersand G Mound Applied Technologies. The purposes of this meeting are to discuss measurement differences, problems, and new measurement capabilities, and to determine the additional activities needed to fulfill the goals of the Exchange. This document provides data for 1992

Tube-in-shell heat exchangers

International Nuclear Information System (INIS)

Richardson, J.

1976-01-01

Tube-in-shell heat exchangers normally comprise a bundle of parallel tubes within a shell container, with a fluid arranged to flow through the tubes in heat exchange with a second fluid flowing through the shell. The tubes are usually end supported by the tube plates that separate the two fluids, and in use the tube attachments to the tube plates and the tube plates can be subject to severe stress by thermal shock and frequent inspection and servicing are required. Where the heat exchangers are immersed in a coolant such as liquid Na such inspection is difficult. In the arrangement described a longitudinally extending central tube is provided incorporating axially spaced cylindrical tube plates to which the opposite ends of the tubes are attached. Within this tube there is a tubular baffle that slidably seals against the wall of the tube between the cylindrical tube plates to define two co-axial flow ducts. These ducts are interconnected at the closed end of the tube by the heat exchange tubes and the baffle comprises inner and outer spaced walls with the interspace containing Ar. The baffle is easily removable and can be withdrawn to enable insertion of equipment for inspecting the wall of the tube and tube attachments and to facilitate plugging of defective tubes. Cylindrical tube plates are believed to be superior for carrying pressure loads and resisting the effects of thermal shock. Some protection against thermal shock can be effected by arranging that the secondary heat exchange fluid is on the tube side, and by providing a thermal baffle to prevent direct impingement of hot primary fluid on to the cylindrical tube plates. The inner wall of the tubular baffle may have flexible expansible region. Some nuclear reactor constructions incorporating such an arrangement are described, including liquid metal reactors. (U.K.)

Four decades of working experience of Cirus primary cooling water heat exchangers

International Nuclear Information System (INIS)

Dubey, P.K.; Ullas, O.P.; Rao, D.V.H.; Zope, A.K.; Kharpate, A.V.

2006-01-01

CIRUS is a 40 MW (Th.) research reactor, commissioned in the year 1960. The reactor has natural uranium fuel rods, heavy water as moderator, demineralised water (DM water) as primary coolant, and seawater as secondary coolant. There are six Heat Exchangers in the primary cooling water (PCW) system. Five of them are required for the normal operation of the reactor and one is kept stand by. DM water flows on the shell side of the heat exchanger in two passes. Seawater is used as coolant on the tube side of the heat exchangers in four passes. Cirus has been in operation for around 41 years excluding refurbishment period. During these four decades of reactor operation, PCW heat exchangers have experienced many failures and undergone many modifications in the circuit for ensuring better performance. This paper tries to capture the essence of working experiences with PCW heat exchangers, various problems faced, remedial measures taken during those four decades of reactor operation. (author)

Next Generation Nuclear Plant Intermediate Heat Exchanger Acquisition Strategy

Energy Technology Data Exchange (ETDEWEB)

Mizia, Ronald Eugene [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2008-04-01

DOE has selected the High Temperature Gas-cooled Reactor (HTGR) design for the Next Generation Nuclear Plant (NGNP) Project. The NGNP will demonstrate the use of nuclear power for electricity and hydrogen production. It will have an outlet gas temperature in the range of 900°C to 950°C and a plant design service life of 60 years. The reactor design will be a graphite moderated, helium cooled, prismatic or pebble-bed reactor, and use low-enriched uranium, TRISO-coated fuel. The plant size, reactor thermal power, and core configuration will ensure passive decay heat removal without fuel damage or radioactive material releases during accidents. The NGNP Materials Research and Development (R&D) Program is responsible for performing R&D on likely NGNP materials in support of the NGNP design, licensing, and construction activities. Selection of the technology and design configuration for the NGNP must consider both the cost and risk profiles to ensure that the demonstration plant establishes a sound foundation for future commercial deployments. The NGNP challenge is to achieve a significant advancement in nuclear technology while at the same time setting the stage for an economically viable deployment of the new technology in the commercial sector soon after 2020. The purpose of this report is to address the acquisition strategy for the NGNP Intermediate Heat Exchanger (IHX).This component will be operated in flowing, impure helium on the primary and secondary side at temperatures up to 950°C. There are major high temperature design, materials availability, and fabrication issues that need to be addressed. The prospective materials are Alloys 617, 230, 800H and X, with Alloy 617 being the leading candidate for the use at 950°C. The material delivery schedule for these materials does not pose a problem for a 2018 start up as the vendors can quote reasonable delivery times at the moment. The product forms and amount needed must be finalized as soon as possible. An

Analysis of uncertainties in the measurements of absorbed dose to water in a secondary standard dosimetry laboratory (SSDL) 60Cobalt

International Nuclear Information System (INIS)

Silva, Cosme Norival Mello da; Rosado, Paulo Henrique Goncalves

2011-01-01

The National Metrology Laboratory of Ionizing Radiation (LNMRI) is the laboratory designated by INMETRO in the field of Metrology of ionizing radiation and is a Secondary Standard Dosimetry Laboratory (SSDL). One of its guidelines is to maintain and disseminate LNMRI absorbed dose in water used as a national standard dosimetry in radiotherapy. For this pattern is metrologically acceptable accuracy and uncertainties should be assessed over time. The objective of this study is to analyze the uncertainties involved in determining the absorbed dose rate in water and standard uncertainty of absorbed dose calibration in water from a clinical dosimeter. The largest sources of uncertainty in determining the rate of absorbed dose in water are due to: calibration coefficient of the calibration certificate supplied by the BIPM, electrometer calibration, camber stability over time, variation of pressure and humidity, strong dependence and non-uniformity of the field. The expanded uncertainty is 0.94% for k = 2. For the calibration standard uncertainty of absorbed dose in water of a dosimeter in a clinical a major source of uncertainty is due to the absorbed dose rate in water (0.94%). The value of expanded uncertainty of calibrating a clinical dosimeter is 1.2% for k = 2. (author)

The Trends and Prospects of Health Information Standards : Standardization Analysis and Suggestions

International Nuclear Information System (INIS)

Kim, Chang Soo

2008-01-01

Ubiquitous health care system, which is one of the developing solution technologies of IT, BT and NT, could give us new medical environments in future. Implementing health information systems can be complex, expensive and frustrating. Healthcare professionals seeking to acquire or upgrade systems do not have a convenient, reliable way of specifying a level of adherence to communication standards sufficient to achieve truly efficient interoperability. Great progress has been made in establishing such standards-DICOM, IHE and HL7, notably, are now highly advanced. IHE has defined a common framework to deliver the basic interoperability needed for local and regional health information networks. It has developed a foundational set of standards-based integration profiles for information exchange with three interrelated efforts. HL7 is one of several ANSI-accredited Standards Developing Organizations operating in the healthcare arena. Most SDOs produce standards (protocols) for a particular healthcare domain such as pharmacy, medical devices, imaging or insurance transactions. HL7's domain is clinical and administrative data. HL7 is an international community of healthcare subject matter experts and information scientists collaborating to create standards for the exchange, management and integration of electronic healthcare information. The ASTM specification for Continuity of Care Record was developed by subcommittee E31.28 on electronic health records, which includes clinicians, provider institutions, administrators, patient advocates, vendors, and health industry. In this paper, there are suggestions that provide a test bed, demonstration and specification of how standards such a IHE, HL7, ASTM can be used to provide an integrated environment.

The Trends and Prospects of Health Information Standards : Standardization Analysis and Suggestions

Energy Technology Data Exchange (ETDEWEB)

Kim, Chang Soo [Dept. of Radiological Science, College of Health Science, Catholic University of Pusan, Pusan (Korea, Republic of)

2008-03-15

Ubiquitous health care system, which is one of the developing solution technologies of IT, BT and NT, could give us new medical environments in future. Implementing health information systems can be complex, expensive and frustrating. Healthcare professionals seeking to acquire or upgrade systems do not have a convenient, reliable way of specifying a level of adherence to communication standards sufficient to achieve truly efficient interoperability. Great progress has been made in establishing such standards-DICOM, IHE and HL7, notably, are now highly advanced. IHE has defined a common framework to deliver the basic interoperability needed for local and regional health information networks. It has developed a foundational set of standards-based integration profiles for information exchange with three interrelated efforts. HL7 is one of several ANSI-accredited Standards Developing Organizations operating in the healthcare arena. Most SDOs produce standards (protocols) for a particular healthcare domain such as pharmacy, medical devices, imaging or insurance transactions. HL7's domain is clinical and administrative data. HL7 is an international community of healthcare subject matter experts and information scientists collaborating to create standards for the exchange, management and integration of electronic healthcare information. The ASTM specification for Continuity of Care Record was developed by subcommittee E31.28 on electronic health records, which includes clinicians, provider institutions, administrators, patient advocates, vendors, and health industry. In this paper, there are suggestions that provide a test bed, demonstration and specification of how standards such a IHE, HL7, ASTM can be used to provide an integrated environment.

Ion-Exchange Processes and Mechanisms in Glasses

International Nuclear Information System (INIS)

McGrail, B.P.; Icenhower, J.P.; Darab, J.G.; Shuh, D.K.; Baer, D.R.; Shutthanandan, V.; Thevuthasan, S.; Engelhard, M.H.; Steele, J.L.; Rodriguez, E.A.; Liu, P.; Ivanov, K.E.; Booth, C.H.; Nachimuthu, P.

2001-01-01

Leaching of alkalis from glass is widely recognized as an important mechanism in the initial stages of glass-water interactions. Pioneering experimental studies [1-3] nearly thirty-five years ago established that alkali (designated as M + ) are lost to solution more rapidly than network-forming cations. The overall chemical reaction describing the process can be written as: (triple b ond)Si-O-M + H + → (triple b ond)Si-OH + M + (1) or (triple b ond)Si-O-M + H 3 O + → (triple b ond)Si-OH + M + + H 2 O. (2) Doremus and coworkers [4-7] fashioned a quantitative model where M + ions in the glass are exchanged for counter-diffusing H 3 O + or H + . Subsequent investigations [8], which have relied heavily on reaction layer analysis, recognized the role of H 2 O molecules in the alkali-exchange process, without minimizing the importance of charged hydrogen species. Beginning in the 1980s, however, interest in M + -H + exchange reactions in silicate glasses diminished considerably because important experimental observations showed that network hydrolysis and dissolution rates were principally controlled by the chemical potential difference between the glass and solution (chemical affinity) [9]. For nuclear waste glasses, formation of alteration products or secondary phases that remove important elements from solution, particularly Si, was found to have very large impacts on glass dissolution rates [10,11]. Consequently, recent work on glass/water interactions has focused on understanding this process and incorporating it into models [12]. The ion-exchange process has been largely ignored because it has been thought to be a short duration, secondary or tertiary process that had little or no bearing on long-term corrosion or radionuclide release rates from glasses [13]. The only significant effect identified in the literature that is attributed to alkali ion exchange is an increase in solution pH in static laboratory tests conducted at high surface area-to-volume ratios

nmrML: A Community Supported Open Data Standard for the Description, Storage, and Exchange of NMR Data.

Science.gov (United States)

Schober, Daniel; Jacob, Daniel; Wilson, Michael; Cruz, Joseph A; Marcu, Ana; Grant, Jason R; Moing, Annick; Deborde, Catherine; de Figueiredo, Luis F; Haug, Kenneth; Rocca-Serra, Philippe; Easton, John; Ebbels, Timothy M D; Hao, Jie; Ludwig, Christian; Günther, Ulrich L; Rosato, Antonio; Klein, Matthias S; Lewis, Ian A; Luchinat, Claudio; Jones, Andrew R; Grauslys, Arturas; Larralde, Martin; Yokochi, Masashi; Kobayashi, Naohiro; Porzel, Andrea; Griffin, Julian L; Viant, Mark R; Wishart, David S; Steinbeck, Christoph; Salek, Reza M; Neumann, Steffen

2018-01-02

NMR is a widely used analytical technique with a growing number of repositories available. As a result, demands for a vendor-agnostic, open data format for long-term archiving of NMR data have emerged with the aim to ease and encourage sharing, comparison, and reuse of NMR data. Here we present nmrML, an open XML-based exchange and storage format for NMR spectral data. The nmrML format is intended to be fully compatible with existing NMR data for chemical, biochemical, and metabolomics experiments. nmrML can capture raw NMR data, spectral data acquisition parameters, and where available spectral metadata, such as chemical structures associated with spectral assignments. The nmrML format is compatible with pure-compound NMR data for reference spectral libraries as well as NMR data from complex biomixtures, i.e., metabolomics experiments. To facilitate format conversions, we provide nmrML converters for Bruker, JEOL and Agilent/Varian vendor formats. In addition, easy-to-use Web-based spectral viewing, processing, and spectral assignment tools that read and write nmrML have been developed. Software libraries and Web services for data validation are available for tool developers and end-users. The nmrML format has already been adopted for capturing and disseminating NMR data for small molecules by several open source data processing tools and metabolomics reference spectral libraries, e.g., serving as storage format for the MetaboLights data repository. The nmrML open access data standard has been endorsed by the Metabolomics Standards Initiative (MSI), and we here encourage user participation and feedback to increase usability and make it a successful standard.

Ontology-based information standards development

OpenAIRE

Heravi, Bahareh Rahmanzadeh

2012-01-01

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University. Standards may be argued to be important enablers for achieving interoperability as they aim to provide unambiguous specifications for error-free exchange of documents and information. By implication, therefore, it is important to model and represent the concept of a standard in a clear, precise and unambiguous way. Although standards development organisations usually provide guidelines for th...

Designing heat exchangers for process heat reactors

International Nuclear Information System (INIS)

Quade, R.N.

1980-01-01

A brief account is given of the IAEA specialist meeting on process heat applications technology held in Julich, November 1979. The main emphasis was on high temperature heat exchange. Papers were presented covering design requirements, design construction and prefabrication testing, and selected problems. Primary discussion centered around mechanical design, materials requirements, and structural analysis methods and limits. It appears that high temperature heat exchanges design to nuclear standards, is under extensive development but will require a lengthy concerted effort before becoming a commercial reality. (author)

Integrating semantic web and software agents : Exchanging RIF and BDI rules

NARCIS (Netherlands)

Gong, Y.; Overbeek, S.J.

2011-01-01

Software agents and rules are both used for creating flexibility. Exchanging rules between Semantic Web and agents can ensure consistency in rules and support easy updating and changing of rules. The Rule Interchange Format (RIF) is a new W3C recommendation Semantic Web standard for exchanging rules

High-dose secondary calibration laboratory accreditation program

Energy Technology Data Exchange (ETDEWEB)

Humphreys, J.C. [National Institute of Standards and Technology, Gaithersburg, MD (United States)

1993-12-31

There is a need for high-dose secondary calibration laboratories to serve the multi-billion dollar radiation processing industry. This need is driven by the desires of industry for less costly calibrations and faster calibration-cycle response time. Services needed include calibration irradiations of routine processing dosimeters and the supply of reference standard transfer dosimeters for irradiation in the production processing facility. In order to provide measurement quality assurance and to demonstrate consistency with national standards, the high-dose secondary laboratories would be accredited by means of an expansion of an existing National Voluntary Laboratory Accreditation Program. A laboratory performance criteria document is under development to implement the new program.

High-dose secondary calibration laboratory accreditation program

International Nuclear Information System (INIS)

Humphreys, J.C.

1993-01-01

There is a need for high-dose secondary calibration laboratories to serve the multi-billion dollar radiation processing industry. This need is driven by the desires of industry for less costly calibrations and faster calibration-cycle response time. Services needed include calibration irradiations of routine processing dosimeters and the supply of reference standard transfer dosimeters for irradiation in the production processing facility. In order to provide measurement quality assurance and to demonstrate consistency with national standards, the high-dose secondary laboratories would be accredited by means of an expansion of an existing National Voluntary Laboratory Accreditation Program. A laboratory performance criteria document is under development to implement the new program

Monju secondary heat transport system sodium leak

International Nuclear Information System (INIS)

Suzuki, Takeo; Hiroi, Hiroshi; Usami, Shin; Iwata, Koji.

1996-01-01

On December 8, 1995, the sodium leakage from the secondary heat transport system (SHTS) occurred in the piping room of the reactor auxiliary building in Monju. The secondary sodium leaked through a temperature sensor, due to the breakaway of the tip of the well tube of the sensor installed near the outlet of the intermediate heat exchanger (IHX) in the C loop of SHTS. The reactor core remained cooled and thus, from the viewpoint of radiological hazards, the safety of the reactor was secured. There were no adverse effects for operating personnel or the surrounding environment. The cause of the well tube failure is considered to result from high cycle fatigue due to flow induced vibrations. Delay in draining the sodium from the leaking loop increased the consequential effects from sodium combustion products. (author)

Numerical Study of Compact Plate-Fin Heat Exchanger for Rotary-Vane Gas Refrigeration Machine

Directory of Open Access Journals (Sweden)

V. V. Trandafilov

2017-10-01

Full Text Available Plate-fin heat exchangers are widely used in refrigeration technique. They are popular because of their compactness and excellent heat transfer performance. Here we present a numerical model for the development, research and optimization of a plate-fin heat exchanger for a rotary-vane gas refrigeration machine. The method of analysis by graphic method of plate - fin heat exchanger is proposed. The model describes the effects of secondary parameters such as axial thermal conductivity through a metal matrix of the heat exchanger. The influence of geometric parameters and heat transfer coefficient is studied. Graphs of dependences of length, efficiency of a fin and pressure drop in a heat exchanger on the thickness of the fin and the number of fins per meter are obtained. To analyze the results of numerical simulation, the heat exchanger was designed in the Aspen HYSYS program. The simulation results show that the total deviation from the proposed numerical model is not more than 15%. 

Overhaul of the heat exchanger in JRR-3

International Nuclear Information System (INIS)

Ouchi, Yasuhiro; Kawamata, Satoshi; Taguchi, Yuji; Kamiishi, Eigo; Koda, Nobuyuki

2013-01-01

In JRR-3, heat exchangers are installed in the cooling system equipment to remove the heat generated in the nuclear reactor, For the heat exchangers, overhaul inspection based on the JRR-3 reactor facility maintenance plan, as well as the inspection and maintenance based on reactor facility security provisions and JRR-3 operation guidelines are systematically conducted. Considering the results of overhaul inspection, the second overhaul inspection was applied to the primary coolant heat exchanger. The thinning of heat transfer tubes is within judgment standards with little effects of aging, which verified their soundness. From the fact that the effects of corrosion have been confirmed on the inside of the water chamber, repair work through overlay welding or the like is planned in the next overhaul. As for heavy water heat exchanger and the spent fuel pool water heat exchanger, it is planned to conduct the second overhaul inspection in FY2013 to confirm their soundness. (A.O.)

Using register data to deduce patterns of social exchange.

Science.gov (United States)

Jansson, Fredrik

2017-07-01

This paper presents a novel method for deducting propensities for social exchange between individuals based on the choices they make, and based on factors such as country of origin, sex, school grades and socioeconomic background. The objective here is to disentangle the effect of social ties from the other factors, in order to find patterns of social exchange. This is done through a control-treatment design on analysing available data, where the 'treatment' is similarity of choices between socially connected individuals, and the control is similarity of choices between non-connected individuals. Structural dependencies are controlled for and effects from different classes are pooled through a mix of methods from network and meta-analysis. The method is demonstrated and tested on Swedish register data on students at upper secondary school. The results show that having similar grades is a predictor of social exchange. Also, previous results from Norwegian data are replicated, showing that students cluster based on country of origin.

Complex use of heat-exchange tunnels

Directory of Open Access Journals (Sweden)

А. Ф. Галкин

2017-04-01

Full Text Available The paper presents separate results of complex research (experimental and theoretical on the application of heat-exchange tunnels – in frozen rocks, among other things – as underground constructions serving two purposes. It is proposed to use heat-exchange tunnels as a separate multi-functional module, which under normal conditions will be used to set standards of heat regime parameters in the mines, and in emergency situations, natural or man-made, will serve as a protective structure to shelter mine workers. Heat-exchange modules can be made from mined-out or specially constructed tunnels. Economic analysis shows that the use of such multi-functional modules does not increase operation and maintenance costs, but enhances safety of mining operations and reliability in case of emergency situations. There are numerous theoretic and experimental investigations in the field of complex use of mining tunnels, which allows to develop regulatory design documents on their basis. Experience of practical application of heat-exchange tunnels has been assessed from the position of regulating heat regime in the mines.

STUDY ON DISCLOSURE LEVEL OF COMPANIES LISTED ON THE BUCHAREST STOCK EXCHANGE IN ACCORDANCE WITH INTERNATIONAL FINANCIAL REPORTING STANDARDS: THE CASE OF INTANGIBLE ASSETS

Directory of Open Access Journals (Sweden)

CĂTĂLINA GORGAN

2014-05-01

Full Text Available In the context of economic globalization, the need for high quality financial information has become a desiderate. Accounting met such needs through a set of high quality standards, the International Financial Reporting Standards. Their global imposing, either through adoption or convergence, make its contribution to proper functioning of capital markets and even of the entire economy. The quality of financial reporting, however, is the result of how they are applied in each country or company. The objective of our study is to analyze the disclosure level of companies listed at Bucharest Stock Exchange (BSE in compliance with the presentation requirements of the international accounting standard IAS 38 “Intangible assets”. The empirical study revealed a significant level of non-compliance. In order to determine the degree of compliance with international accounting referential we built a disclosure index. Four hypothesis were tested in order to identify the factors that influence the disclosure level.

Standardized Elemental Basis for Gas-Turbine Engine Heat Exchangers is the Key Factor for Their Cost Reduction

Institute of Scientific and Technical Information of China (English)

Soudarev A.V; Soudarev B.V; Kondratiev V.V; Lazarev M.V

2001-01-01

The competitiveness of the small gas turbine units (GTUs) (Ne＜300 kW) in the world power market is dependent on both the maintenance expenses and the capital costs of production. Reduction in the maintenance expenditures could be achieved by increasing the plant efficiency. This task could be solved by some methods: increasing the cycle inlet temperature TIT, getting the cycle more complex (use of heat regeneration and compressed air intermediate cooling), cutting the power consumption on heat-stressed parts cooling. Putting the above into effect is linked with introduction of novel structural materials, a sharp increase in the mass-size values and the plant manufacture expenditures, in particular, at provision of its self-regulation.In connection with the above, the development of the combined metal-ceramic airheaters and standardization of the elemental basis of the metal gas-gas heat exchangers will promote reduction in the expenditures of the maintenance and the manufacture of the small-size independent power GTEs.

A Survey of the Reading Habit of Exchange Students of Government ...

African Journals Online (AJOL)

The focus of this paper is on "a survey of the reading habit of exchange students of Government Secondary School and Queen Elizabeth School, Ilorin Kwara State". The students were drawn from seventeen states in Northern Nigeria. Causes of the low reading habit were identified, highlighted and the effects on their ...

Thermal performance modeling of cross-flow heat exchangers

CERN Document Server

Cabezas-Gómez, Luben; Saíz-Jabardo, José Maria

2014-01-01

This monograph introduces a numerical computational methodology for thermal performance modeling of cross-flow heat exchangers, with applications in chemical, refrigeration and automobile industries. This methodology allows obtaining effectiveness-number of transfer units (e-NTU) data and has been used for simulating several standard and complex flow arrangements configurations of cross-flow heat exchangers. Simulated results have been validated through comparisons with results from available exact and approximate analytical solutions. Very accurate results have been obtained over wide ranges

17 CFR 240.19c-5 - Governing the multiple listing of options on national securities exchanges.

Science.gov (United States)

2010-04-01

... of options on national securities exchanges. 240.19c-5 Section 240.19c-5 Commodity and Securities... of Exchange Members § 240.19c-5 Governing the multiple listing of options on national securities exchanges. (a) The rules of each national securities exchange that provides a trading market in standardized...

Business Information Exchange System with Security, Privacy, and Anonymity

Directory of Open Access Journals (Sweden)

Sead Muftic

2016-01-01

Full Text Available Business Information Exchange is an Internet Secure Portal for secure management, distribution, sharing, and use of business e-mails, documents, and messages. It has three applications supporting three major types of information exchange systems: secure e-mail, secure instant messaging, and secure sharing of business documents. In addition to standard security services for e-mail letters, which are also applied to instant messages and documents, the system provides innovative features of privacy and full anonymity of users and their locations, actions, transactions, and exchanged resources. In this paper we describe design, implementation, and use of the system.

The political economy of international accounting standards

NARCIS (Netherlands)

Perry, J.; Nolke, A.

2006-01-01

On 1 January 2005, all stock exchange listed companies in the European Union (EU) began using International Financial Reporting Standards (IFRS) written by the International Accounting Standards Board (IASB). This article argues that the IASB's introduction of fair value accounting reflects and

XTCE (XML Telemetric and Command Exchange) Standard Making It Work at NASA. Can It Work For You?

Science.gov (United States)

Munoz-Fernandez, Michela; Smith, Danford S.; Rice, James K.; Jones, Ronald A.

2017-01-01

The XML Telemetric and Command Exchange (XTCE) standard is intended as a way to describe telemetry and command databases to be exchanged across centers and space agencies. XTCE usage has the potential to lead to consolidation of the Mission Operations Center (MOC) Monitor and Control displays for mission cross-support, reducing equipment and configuration costs, as well as a decrease in the turnaround time for telemetry and command modifications during all the mission phases. The adoption of XTCE will reduce software maintenance costs by reducing the variation between our existing mission dictionaries. The main objective of this poster is to show how powerful XTCE is in terms of interoperability across centers and missions. We will provide results for a use case where two centers can use their local tools to process and display the same mission telemetry in their MOC independently of one another. In our use case we have first quantified the ability for XTCE to capture the telemetry definitions of the mission by use of our suite of support tools (Conversion, Validation, and Compliance measurement). The next step was to show processing and monitoring of the same telemetry in two mission centers. Once the database was converted to XTCE using our tool, the XTCE file became our primary database and was shared among the various tool chains through their XTCE importers and ultimately configured to ingest the telemetry stream and display or capture the telemetered information in similar ways.Summary results include the ability to take a real mission database and real mission telemetry and display them on various tools from two centers, as well as using commercially free COTS.

76 FR 18966 - Listing Standards for Compensation Committees

Science.gov (United States)

2011-04-06

... director. For this purpose, remuneration includes any payment in exchange for goods or services. Section... the board of directors and to be ``independent,'' as defined in the listing standards of the exchanges... requirements for members of the compensation committee of the board of directors of an issuer. In accordance...

Assessment of flow induced vibration in a sodium-sodium heat exchanger

Energy Technology Data Exchange (ETDEWEB)

Prakash, V. [Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu (India)], E-mail: prakash@igcar.gov.in; Thirumalai, M.; Prabhakar, R.; Vaidyanathan, G. [Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu (India)

2009-01-15

The 500 MWe Prototype Fast Breeder Reactor (PFBR) is under construction at Kalpakkam. It is a liquid metal sodium cooled pool type fast reactor with all primary components located inside a sodium pool. The heat produced due to fission in the core is transported by primary sodium to the secondary sodium in a sodium to sodium Intermediate Heat Exchanger (IHX), which in turn is transferred to water in the steam generator. PFBR IHX is a shell and tube type heat exchanger with primary sodium on shell side and secondary sodium in the tube side. Since IHX is one of the critical components placed inside the radioactive primary sodium, trouble-free operation of the IHX is very much essential for power plant availability. To validate the design and the adequacy of the support system provided for the IHX, flow induced vibration (FIV) experiments were carried out in a water test loop on a 60 deg. sector model. This paper discusses the flow induced vibration measurements carried out in 60 deg. sector model of IHX, the modeling criteria, the results and conclusion.

Implantation of a new Beta Secondary Standard system at Centro de Desenvolvimento da Tecnologia Nuclear

International Nuclear Information System (INIS)

Reynaldo, Sibele Reis

2005-01-01

The crescent use of beta radiation sources in medical, industrial and research applications has increased the need for higher accuracy in beta dosimetry. As the first Beta Secondary Standard system (BSS1) was developed about 20 years ago, a new BSS2 system was made commercially available to fulfill new metrological demands and to follow the technological development. The BSS2 has a new positioning set-up, high activity and long half-life beta radiation sources and a special safety system. The Centro de Desenvolvimento da Tecnologia Nuclear is the first laboratory in Latin America that has got a BSS2. This work describes the BSS2 and it compares its advantages in relation to BSS1; results of the beam uniformity tests of the radiation fields from 90 Sr/ 90 Y, 85 Kr and 147 Pm sources, that were measured with an ionization chamber and with thermoluminescent detectors, are also shown. Results show that the beta radiation fields are considered to be uniform for diameters between 8 and 20 cm according to the chosen source. (author)

Monorail Piccolino catheter: a new rapid exchange/ultralow profile coronary angioplasty system.

Science.gov (United States)

Mooney, M R; Douglas, J S; Mooney, J F; Madison, J D; Brandenburg, R O; Fernald, R; Van Tassel, R A

1990-06-01

The Monorail Piccolino coronary angioplasty balloon catheter (MBC) was evaluated on 118 patients at two centers. Technical success was achieved in 110 patients (93%). Time for catheter exchange and total fluoroscopy time were significantly lower for the Monorail catheter than with standard equipment (exchange time 97 vs. 170 seconds P less than .05 and fluoroscopy time 17 vs. 88 seconds P less than .001). The advantages of rapid exchange and the ability of utilize 2 Monorail balloon catheters through one 9F guiding catheter for simultaneous inflations allowed for maximal flexibility in treating patients with bifurcation lesions. The double wire approach utilizing one Monorail balloon catheter with a 7F guiding catheter was also technically successful. The Monorail Piccolino balloon catheter has unique features that allow for greater ease of operator use, rapid catheter exchange, and optimal angiographic visualization. It is felt that this catheter design provides distinct advantages over standard angioplasty equipment.

Standardizing data exchange for clinical research protocols and case report forms: An assessment of the suitability of the Clinical Data Interchange Standards Consortium (CDISC) Operational Data Model (ODM).

Science.gov (United States)

Huser, Vojtech; Sastry, Chandan; Breymaier, Matthew; Idriss, Asma; Cimino, James J

2015-10-01

Efficient communication of a clinical study protocol and case report forms during all stages of a human clinical study is important for many stakeholders. An electronic and structured study representation format that can be used throughout the whole study life-span can improve such communication and potentially lower total study costs. The most relevant standard for representing clinical study data, applicable to unregulated as well as regulated studies, is the Operational Data Model (ODM) in development since 1999 by the Clinical Data Interchange Standards Consortium (CDISC). ODM's initial objective was exchange of case report forms data but it is increasingly utilized in other contexts. An ODM extension called Study Design Model, introduced in 2011, provides additional protocol representation elements. Using a case study approach, we evaluated ODM's ability to capture all necessary protocol elements during a complete clinical study lifecycle in the Intramural Research Program of the National Institutes of Health. ODM offers the advantage of a single format for institutions that deal with hundreds or thousands of concurrent clinical studies and maintain a data warehouse for these studies. For each study stage, we present a list of gaps in the ODM standard and identify necessary vendor or institutional extensions that can compensate for such gaps. The current version of ODM (1.3.2) has only partial support for study protocol and study registration data mainly because it is outside the original development goal. ODM provides comprehensive support for representation of case report forms (in both the design stage and with patient level data). Inclusion of requirements of observational, non-regulated or investigator-initiated studies (outside Food and Drug Administration (FDA) regulation) can further improve future revisions of the standard. Published by Elsevier Inc.

A Method to Establishing Tube Plugging Criterion for Heat Exchangers with Straight Tubes

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyungnam [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

The difference of thermal expansion coefficients between the shell and tube materials causes the stress in axial direction of tube. Because of the axial stress due to thermal load, the straight tubes are used for heat exchangers operated in low temperature such as CCW (Component Cooling Water) heat exchangers and condensers. It is inevitable for the materials of the components to be degraded as the power plants become older. The degradation accompanies increasing maintenance cost as well as creating safety issues. The materials and wall thickness of heat exchanger tubes in nuclear power plants are selected to withstand system temperature, pressure, and corrosion. There are many codes and standards to be referred for calculating the minimum thickness of the heat exchanger tube in the designing stage. However, the codes and standards related to show the tube plugging criteria may not exist currently. In this paper, a method to establish the tube plugging criteria of BOP heat exchangers, which is based on the USNRC Regulatory Guide 1.121, is introduced and the tube plugging criteria for the TPCCW heat exchanger of Yonggwang NPP No. 1 and 2. A method to establish the tube plugging criteria of heat exchangers with straight tubes are introduced based on the USNRC Regulatory Guide 1.121. As an example, the tube plugging criterion for the CCW heat exchanger of a nuclear power plant is provided.

THE NORMALIZATION OF FINANCIAL DATA EXCHANGE OVER THE INTERNET: ADOPTING INTERNATIONAL STANDARD XBRL

Directory of Open Access Journals (Sweden)

Catalin Georgel Tudor

2009-05-01

Full Text Available The development of a common syntax for EDI (Electronic Data Interchange, XML (eXtensible Markup Language, opened new formalization perspectives for interorganizational data exchanges over the Internet. Many of the organizations involved in the normaliza

Replica exchange with solute tempering: A method for sampling biological systems in explicit water

Science.gov (United States)

Liu, Pu; Kim, Byungchan; Friesner, Richard A.; Berne, B. J.

2005-09-01

An innovative replica exchange (parallel tempering) method called replica exchange with solute tempering (REST) for the efficient sampling of aqueous protein solutions is presented here. The method bypasses the poor scaling with system size of standard replica exchange and thus reduces the number of replicas (parallel processes) that must be used. This reduction is accomplished by deforming the Hamiltonian function for each replica in such a way that the acceptance probability for the exchange of replica configurations does not depend on the number of explicit water molecules in the system. For proof of concept, REST is compared with standard replica exchange for an alanine dipeptide molecule in water. The comparisons confirm that REST greatly reduces the number of CPUs required by regular replica exchange and increases the sampling efficiency. This method reduces the CPU time required for calculating thermodynamic averages and for the ab initio folding of proteins in explicit water. Author contributions: B.J.B. designed research; P.L. and B.K. performed research; P.L. and B.K. analyzed data; and P.L., B.K., R.A.F., and B.J.B. wrote the paper.Abbreviations: REST, replica exchange with solute tempering; REM, replica exchange method; MD, molecular dynamics.*P.L. and B.K. contributed equally to this work.

Atmospheric pressure photo ionization hydrogen/deuterium exchange mass spectrometry--a method to differentiate isomers by mass spectrometry.

Science.gov (United States)

Ahmed, Arif; Kim, Sunghwan

2013-12-01

In this report, a method for in-source hydrogen/deuterium (H/D) exchange at atmospheric pressure is reported. The method was named atmospheric pressure photo ionization hydrogen/deuterium exchange mass spectrometry (APPI HDX MS). H/D exchange was performed by mixing samples dissolved in toluene with CH3OD solvent and analyzing the mixture using atmospheric pressure photo ionization mass spectrometry (APPI-MS). The APPI HDX spectra obtained with contact times between the analyte solution and methanol-OD (CH3OD) of atmospheric pressure. H/D exchange can be performed in any laboratory with a mass spectrometer and a commercial APPI source. Using this method, multiple H/D exchanges of aromatic hydrogen and/or H/D exchange of active hydrogen were observed. These results demonstrated that H/D exchange can be used to distinguish between isomers containing primary, secondary, and tertiary amines, as well as pyridine and pyrrole functional groups.

40 CFR 421.206 - Pretreatment standards for new sources.

Science.gov (United States)

2010-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Mercury Subcategory... wastewater pollutants in secondary mercury process wastewater introduced into a POTW shall not exceed the following values: (a) Spent battery electrolyte. PSNS for the Secondary Mercury Subcategory Pollutant or...

Design, construction and operation experience of the He-He intermediate heat exchanger

International Nuclear Information System (INIS)

Itoh, M.

1980-01-01

The conditions required for the primary helium, which is the cooling medium for the high temperature gas cooled reactor, are prescribed to be 1,000 0 C in temperature and 40 kgf/cm 2 in pressure at the outlet of the reactor, while the conditions required for the secondary helium at the outlet of the intermediate heat exchanger are prescribed to be 925 0 C in temperature and 45 kgf/cm 2 in pressure. This means that relatively high temperatures and high pressure are required for the system. The purpose of the present research and development project is to establish a design method, safety evaluation techniques, and safety-securing measures to be applied to an intermediate heat exchanger and to the overall heat exchanging system, which will satisfy those strict operating conditions as mentioned above. Research and development work on the high temperature heat exchanger has been and is being carried out

ASME code considerations for the compact heat exchanger

Energy Technology Data Exchange (ETDEWEB)

Nestell, James [MPR Associates Inc., Alexandria, VA (United States); Sham, Sam [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-08-31

The mission of the U.S. Department of Energy (DOE), Office of Nuclear Energy is to advance nuclear power in order to meet the nation's energy, environmental, and energy security needs. Advanced high temperature reactor systems such as sodium fast reactors and high and very high temperature gas-cooled reactors are being considered for the next generation of nuclear reactor plant designs. The coolants for these high temperature reactor systems include liquid sodium and helium gas. Supercritical carbon dioxide (sCO₂), a fluid at a temperature and pressure above the supercritical point of CO₂, is currently being investigated by DOE as a working fluid for a nuclear or fossil-heated recompression closed Brayton cycle energy conversion system that operates at 550°C (1022°F) at 200 bar (2900 psi). Higher operating temperatures are envisioned in future developments. All of these design concepts require a highly effective heat exchanger that transfers heat from the nuclear or chemical reactor to the chemical process fluid or the to the power cycle. In the nuclear designs described above, heat is transferred from the primary to the secondary loop via an intermediate heat exchanger (IHX) and then from the intermediate loop to either a working process or a power cycle via a secondary heat exchanger (SHX). The IHX is a component in the primary coolant loop which will be classified as "safety related." The intermediate loop will likely be classified as "not safety related but important to safety." These safety classifications have a direct bearing on heat exchanger design approaches for the IHX and SHX. The very high temperatures being considered for the VHTR will require the use of very high temperature alloys for the IHX and SHX. Material cost considerations alone will dictate that the IHX and SHX be highly effective; that is, provide high heat transfer area in a small volume. This feature must be accompanied by low pressure drop and mechanical reliability and

Standard biological parts knowledgebase.

Directory of Open Access Journals (Sweden)

Michal Galdzicki

2011-02-01

Full Text Available We have created the Knowledgebase of Standard Biological Parts (SBPkb as a publically accessible Semantic Web resource for synthetic biology (sbolstandard.org. The SBPkb allows researchers to query and retrieve standard biological parts for research and use in synthetic biology. Its initial version includes all of the information about parts stored in the Registry of Standard Biological Parts (partsregistry.org. SBPkb transforms this information so that it is computable, using our semantic framework for synthetic biology parts. This framework, known as SBOL-semantic, was built as part of the Synthetic Biology Open Language (SBOL, a project of the Synthetic Biology Data Exchange Group. SBOL-semantic represents commonly used synthetic biology entities, and its purpose is to improve the distribution and exchange of descriptions of biological parts. In this paper, we describe the data, our methods for transformation to SBPkb, and finally, we demonstrate the value of our knowledgebase with a set of sample queries. We use RDF technology and SPARQL queries to retrieve candidate "promoter" parts that are known to be both negatively and positively regulated. This method provides new web based data access to perform searches for parts that are not currently possible.

Standard Biological Parts Knowledgebase

Science.gov (United States)

Galdzicki, Michal; Rodriguez, Cesar; Chandran, Deepak; Sauro, Herbert M.; Gennari, John H.

2011-01-01

We have created the Knowledgebase of Standard Biological Parts (SBPkb) as a publically accessible Semantic Web resource for synthetic biology (sbolstandard.org). The SBPkb allows researchers to query and retrieve standard biological parts for research and use in synthetic biology. Its initial version includes all of the information about parts stored in the Registry of Standard Biological Parts (partsregistry.org). SBPkb transforms this information so that it is computable, using our semantic framework for synthetic biology parts. This framework, known as SBOL-semantic, was built as part of the Synthetic Biology Open Language (SBOL), a project of the Synthetic Biology Data Exchange Group. SBOL-semantic represents commonly used synthetic biology entities, and its purpose is to improve the distribution and exchange of descriptions of biological parts. In this paper, we describe the data, our methods for transformation to SBPkb, and finally, we demonstrate the value of our knowledgebase with a set of sample queries. We use RDF technology and SPARQL queries to retrieve candidate “promoter” parts that are known to be both negatively and positively regulated. This method provides new web based data access to perform searches for parts that are not currently possible. PMID:21390321

Standard biological parts knowledgebase.

Science.gov (United States)

Galdzicki, Michal; Rodriguez, Cesar; Chandran, Deepak; Sauro, Herbert M; Gennari, John H

2011-02-24

We have created the Knowledgebase of Standard Biological Parts (SBPkb) as a publically accessible Semantic Web resource for synthetic biology (sbolstandard.org). The SBPkb allows researchers to query and retrieve standard biological parts for research and use in synthetic biology. Its initial version includes all of the information about parts stored in the Registry of Standard Biological Parts (partsregistry.org). SBPkb transforms this information so that it is computable, using our semantic framework for synthetic biology parts. This framework, known as SBOL-semantic, was built as part of the Synthetic Biology Open Language (SBOL), a project of the Synthetic Biology Data Exchange Group. SBOL-semantic represents commonly used synthetic biology entities, and its purpose is to improve the distribution and exchange of descriptions of biological parts. In this paper, we describe the data, our methods for transformation to SBPkb, and finally, we demonstrate the value of our knowledgebase with a set of sample queries. We use RDF technology and SPARQL queries to retrieve candidate "promoter" parts that are known to be both negatively and positively regulated. This method provides new web based data access to perform searches for parts that are not currently possible.

Heat exchanges between droplets and atmosphere

International Nuclear Information System (INIS)

Yadigaroglu, Georges.

1975-01-01

Data necessary for calculating the droplet cooling in wet cooling systems are surveyed. This cooling obeys the laws of simultaneous heat and mass transfer. Exchanges with a solid sphere moving inside a surrounding fluid medium are first examined. The corrections needed for taking into account various secondary effects (circulation in the droplet, lack of sphericity, oscillations, etc...) are then dealt with. Some data necessary for calculating the trajectories of the droplets and their behavior in a cooling system are included (diameter distribution, limit velocities, decay thresholds, etc...). Finally, calculation methods applying to spray systems, as well as wet towers broadly outlined [fr

Performance analyses of helical coil heat exchangers. The effect of external coil surface modification on heat exchanger effectiveness

Science.gov (United States)

Andrzejczyk, Rafał; Muszyński, Tomasz

2016-12-01

The shell and coil heat exchangers are commonly used in heating, ventilation, nuclear industry, process plant, heat recovery and air conditioning systems. This type of recuperators benefits from simple construction, the low value of pressure drops and high heat transfer. In helical coil, centrifugal force is acting on the moving fluid due to the curvature of the tube results in the development. It has been long recognized that the heat transfer in the helical tube is much better than in the straight ones because of the occurrence of secondary flow in planes normal to the main flow inside the helical structure. Helical tubes show good performance in heat transfer enhancement, while the uniform curvature of spiral structure is inconvenient in pipe installation in heat exchangers. Authors have presented their own construction of shell and tube heat exchanger with intensified heat transfer. The purpose of this article is to assess the influence of the surface modification over the performance coefficient and effectiveness. The experiments have been performed for the steady-state heat transfer. Experimental data points were gathered for both laminar and turbulent flow, both for co current- and countercurrent flow arrangement. To find optimal heat transfer intensification on the shell-side authors applied the number of transfer units analysis.

1996 DOE technical standards program workshop: Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

The workshop theme is `The Strategic Standardization Initiative - A Technology Exchange and Global Competitiveness Challenge for DOE.` The workshop goal is to inform the DOE technical standards community of strategic standardization activities taking place in the Department, other Government agencies, standards developing organizations, and industry. Individuals working on technical standards will be challenged to improve cooperation and communications with the involved organizations in response to the initiative. Workshop sessions include presentations by representatives from various Government agencies that focus on coordination among and participation of Government personnel in the voluntary standards process; reports by standards organizations, industry, and DOE representatives on current technology exchange programs; and how the road ahead appears for `information superhighway` standardization. Another session highlights successful standardization case studies selected from several sites across the DOE complex. The workshop concludes with a panel discussion on the goals and objectives of the DOE Technical Standards Program as envisioned by senior DOE management. The annual workshop on technical standards has proven to be an effective medium for communicating information related to standards throughout the DOE community. Technical standards are used to transfer technology and standardize work processes to produce consistent, acceptable results. They provide a practical solution to the Department`s challenge to protect the environment and the health and safety of the public and workers during all facility operations. Through standards, the technologies of industries and governments worldwide are available to DOE. The DOE Technical Standards Program, a Department-wide effort that crosscuts all organizations and disciplines, links the Department to those technologies.

Secondary Students' Perceptions of Open Science Textbooks

Science.gov (United States)

Morales, Rebecca; Baker, Alesha

2018-01-01

In an attempt to align instructional resources with new state standards and to increase teacher awareness of these standards, one large suburban public school district piloted the development and adoption of open secondary science textbooks. Open textbooks created by teachers in grades six through nine replaced conventional science textbooks…

Stress analysis of HTR-10 steam generator heat exchanging tubes

International Nuclear Information System (INIS)

Dong Jianling; Zhang Xiaohang; Yin Dejian; Fu Jiyang

2001-01-01

Steam Generator (SG) heat exchanging tubes of 10 MW High Temperature Gas Cooled Reactor (HTR-10) are protective screens between the primary loop of helium with radioactivity and the secondary loop of feeding water and steam without radioactivity. Water and steam will enter into the primary loop when rupture of the heat exchanging tubes occurs, which lead to increase of the primary loop pressure and discharge of radioactive materials. Therefore it is important to guarantee the integrity of the tubes. The tube structure is spiral tube with small bending radius, which make it impossible to test with volumetric in-service detection. For such kind of spiral tube, using LBB concept to guarantee the integrity of the tubes is an important option. The author conducts stress analysis and calculation of HTR-10 SG heat exchanging tubes using the FEM code of piping stress analysis, PIPESTRESS. The maximum stress and the dangerous positions are obtained

Preliminary study on high temperature heat exchanger for nuclear steel making

Energy Technology Data Exchange (ETDEWEB)

Nakada, T; Ohtomo, A; Yamada, R; Suzuki, K; Narita, Y [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

1975-05-01

Both in the high temperature heat exchanger and in the steam reformer, there remain several technical problems to be solved before nuclear steel making is actualized. The loop for use with basic studies of those problems was planned by the Iron and Steel Institute of Japan (ISIJ), and its actual design, construction and co-ordination of tests were undertaken by IHI on behalf of ISIJ. The primary coolant used in the loop was helium having a pressure of approx. 12 kg/cm/sup 2/g and a temperature of approx. 1100/sup 0/C at the inlet of the high temperature heat exchanger, i.e., the test section. Steam, hydrogen, and carbon monoxide were used as secondary coolants. Of the technical problems regarding the high temperature heat exchanger for nuclear steel making, which were selected and studied using the loop, the following items are discussed: (1) heat exchange performance using helium and steam; (2) hydrogen permeation of heat resisting alloys; (3) creep and carburization of heat resisting alloys; amd (4) hydrogen absorption performance of the titanium sponge.

78 FR 30367 - Self-Regulatory Organizations; BOX Options Exchange LLC; Notice of Filing and Immediate...

Science.gov (United States)

2013-05-22

... product by keeping the Jumbo SPY Options fees low and easy for investors to understand. The Exchange... charge the same rate for transactions in Jumbo SPY Options, since the costs to the Exchange to process... charge the ORF at the same rate as the standard contract. 2. Statutory Basis The Exchange believes that...

40 CFR 421.246 - Pretreatment standards for new sources.

Science.gov (United States)

2010-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Nickel Subcategory... reclaim leaching belt filter backwash. PSNS for the Secondary Nickel Subcategory Pollutant or pollutant...

Secondary Aluminum National Emission Standards for Hazardous Air Pollutants (NESHAP) Applicability Flowcharts

Science.gov (United States)

This March 2003 document contains three diagrams that that are intended to assist you in determining whether you own or operate any equipment that is subject to the NESHAP for Secondary Aluminum Production Facilities.

Ultrafiltration Membrane Fouling and the Effect of Ion Exchange Resins

KAUST Repository

Jamaly, Sanaa

2011-12-01

Membrane fouling is a challenging process for the ultrafiltration membrane during wastewater treatment. This research paper determines the organic character of foulants of different kinds of wastewater before and after adding some ion exchange resins. Two advanced organic characterization methods are compared in terms of concentration of dissolved organic carbons: The liquid chromatography with organic carbon (LC-OCD) and Shimadzu total organic carbon (TOC). In this study, two secondary wastewater effluents were treated using ultrafiltration membrane. To reduce fouling, pretreatment using some adsorbents were used in the study. Six ion exchange resins out of twenty were chosen to compare the effect of adsorbents on fouling membrane. Based on the percent of dissolved organic carbon’s removal, three adsorbents were determined to be the most efficient (DOWEX Marathon 11 anion exchange resin, DOWEX Optipore SD2 polymeric adsorbent, and DOWEX PSR2 anion exchange), and three other ones were determined to the least efficient (DOWEX Marathon A2 anion exchange resin, DOWEX SAR anion exchange resin, and DOWEX Optipore L493 polymeric adsorbent). Organic characterization for feed, permeate, and backwash samples were tested using LC-OCD and TOC to better understand the characteristics of foulants to prevent ultrafiltration membrane fouling. The results suggested that the polymeric ion exchange resin, DOWEX SD2, reduced fouling potential for both treated wastewaters. All the six ion exchange resins removed more humic fraction than other organic fractions in different percent, so this fraction is not the main for cause for UF membrane fouling. The fouling of colloids was tested before and after adding calcium. There is a severe fouling after adding Ca2+ to effluent colloids.

Secondary School Curricula Issues: Impact on Postsecondary Students with Disabilities.

Science.gov (United States)

Stodden, Robert A.; Galloway, L. M.; Stodden, Norma Jean

2003-01-01

This article examines the complex needs of students with disabilities in learning rigorous standards-based curricula, the need of educators to teach this population standards-based curricula effectively, and the contextual factors that affect teaching and learning standards-based curricula in secondary schools. Exemplary and promising practices…

On Surface Order and Disorder of α-Pinene-Derived Secondary Organic Material

Energy Technology Data Exchange (ETDEWEB)

Shrestha, Mona; Zhang, Yue; Upshur, Mary Alice; Liu, Pengfei; Blair, Sandra L.; Wang, Hongfei; Nizkorodov, Sergey; Thomson, Regan; Martin, Scot T.; Geiger, Franz M.

2015-05-14

The surfaces of secondary organic aerosol particles are notoriously difficult to access experimentally, even though they are the key location where exchange between the aerosol particle phase and its gas phase occurs. Here, we overcome this difficulty by applying standard and sub 1-cm-1 resolution vibrational sum frequency generation (SFG) spectroscopy to detect C–H oscillators at the surfaces of secondary organic material (SOM) prepared from the ozonolysis of α-pinene at Harvard University and at the University of California, Irvine that were subsequently collected on Teflon filters as well as CaF2 windows using electrostatic deposition. We find both samples yield comparable SFG spectra featuring an intense peak at 2940 cm-1 that are independent of spectral resolution and location or method of preparation. We hypothesize that the SFG spectra are due to surface-active C–H oscillators associated with the four-membered ring motif of α-pinene, which produces an unresolvable spectral continuum of approximately 50 cm-1 width reminiscent of the similar, albeit much broader, O–H stretching continuum observed in the SFG spectra of aqueous surfaces. Upon subjecting the SOM samples to cycles in relative humidity (RH) between <2% RH and 95% RH, we observe reversible changes in the SFG signal intensity across the entire spectral range surveyed for a polarization combination probing components of the vibrational transition dipole moments that are oriented parallel to the plane of incidence, but no signal intensity changes for any other polarization combination investigated. These results support the notion that the C–H oscillators at the surfaces of α-pinene-derived SOM deposited on CaF2 windows shift back and forth between two different molecular orientation distributions as the RH is lowered (more ordered) or raised (less ordered). The findings thus point towards the presence of a reversible surface switch for hindering (more ordered, <2%RH) and promoting (less

Dynamic thermal baffle on lower head of FBR sodium-sodium intermediate heat exchanger

International Nuclear Information System (INIS)

Charbonnel, A.; Foussat, C.

1981-01-01

The cover head of the heat exchanger is bathed on the one side by the primary sodium of the 'cold' header of the vessel and on the other side by the secondary sodium which feeds the heat exchange tube bank through the lower tubesheet. In the case of transient or permanent operating conditions at partial ratings, there are large temperature differences between the inner sodium (inlet temperature conditions of secondary sodium) and the outer sodium (mean temperature conditions in the primary sodium outlet port), hence the necessity of designing a thermal baffle which protects the head and its connection to the tubesheet. A 'static' thermal baffle consisting of a thick steel plate enclosing static sodium around the head proves inadequate during transient operating conditions. This is why a 'dynamic' thermal baffle is used whose design is based on the fact that the primary sodium in the lower part of the outlet port is always at a temperature close to that of the secondary sodium in the inlet header and the head. The primary sodium is taken from the bottom of the outlet port by a ring deflector and circulates in an annulus created by a double housing and the head. It flows out through openings in the lower part of the housing. (orig./GL)

Steam generator blowdown heat exchangers degradations operational experience on EDF French NPP fleet

International Nuclear Information System (INIS)

Praud, M.; Doyen, F.; Wintergest, M.; Jourdain, W.; Roussillon, M.; Zidane, A.; Mayos, M.

2015-01-01

The main function of the Steam Generator Blowdown System (SGBS) is to purify the secondary fluid from all kinds of pollutions: corrosion products from the secondary system, consequences of raw water pollutions through condenser's leakage, potential radiochemical pollutions resulting from Primary-to-Secondary leaks. The topic of this paper is to present the main SGBS dysfunctions linked to the degradation of the tubular heat exchangers, which sometimes can lead to integrity failure, through corrosion phenomenon. The degradation mechanisms have been characterized by various visual inspections and destructive examinations performed on pulled tubes and bundles. It appears that SGBS tubes suffer two main forms of corrosion. First, for the non-regenerative heat exchangers, where external surface of tubes is exposed to intermediate fluid, alkaline corrosion under tube sheet or shell-side baffles may occur. Caustic attack results from Na 3 PO 4 decomposition by thermal or chemical process. Secondly, mainly for regenerative heat exchangers, pitting and under-deposits corrosion linked to lay-up conditions during outages. This kind of attack is the root cause of a potential 'domino effect': a steam jet from the leaking tube can induce mechanical and/or erosion on many tubes located in its vicinity. Concerning the external degradation by caustic corrosion, only design modifications and strong monitoring of the raw water inlet may able to limit the occurrence of tube perforation. The lay-up guidelines should be carefully followed to mitigate internal corrosion: a controlled atmosphere (limited humidity) and cleanliness of the tube (avoiding deposits formation on the bottom line) seem to be the main parameters

Inquiry of selected topics on heat exchanger design

International Nuclear Information System (INIS)

Mueller, A.C.

1977-01-01

Three specific topics of heat exchanger design are discussed. First is an examination of the effect of maldistribution on the performance of an exchanger. Three different patterns of maldistribution are investigated and for each type when the overall coefficient is independent of the maldistribution (constant) and when the maldistributed fluid is the controlling resistance and, hence, is a function of the maldistribution. It is the purpose of this investigation to determine how serious the maldistribution problem can be and hopefully, develop guidelines for the designer. Second, the simple laminar flow in tube heat transfer problem was examined with the further complications of appreciable external resistance and for countercurrent flow with appreciable temperature changes in the secondary fluid. This is a complex problem theoretically and it is shown how this would be simplified by means of several simple plots. Based on an old analog solution, the possible error if one used the conventional methods of applying overall coefficients in the design of laminar flow exchangers is discussed. Third, laminar flow heat transfer in tube banks was reviewed. The fundamental problem here is how does one handle the effect of the number of tube rows in baffled exchangers. Another form of correlation is suggested but basically it was found that insufficient experimental data were available to determine the best form of correlation. Further experimental data are needed

Calibration of photon and beta ray sources used in brachytherapy. Guidelines on standardized procedures at Secondary Standards Dosimetry Laboratories

International Nuclear Information System (INIS)

2004-03-01

It has generally been recognized that international harmonization in radiotherapy dosimetry is essential. Consequently, the IAEA has given much effort to this, for example by publishing a number of reports in the Technical Reports Series (TRS) for external beam dosimetry, most notably TRS-277 and more recently TRS-398. Both of these reports describe in detail the steps to be taken for absorbed dose determination in water and they are often referred to as 'dosimetry protocols'. Similar to TRS-277, it is expected that TRS-398 will be adopted or used as a model by a large number of countries as their national protocol. In 1996, the IAEA established a calibration service for low dose rate (LDR) 137 Cs brachytherapy sources, which is the most widely used source for treatment of gynecological cancer. To further enhance harmonization in brachytherapy dosimetry, the IAEA published in 1999 IAEA-TECDOC-1079 entitled 'Calibration of Brachytherapy Sources. Guidelines on Standardized Procedures for the Calibration of Brachytherapy Sources at Secondary Standard Dosimetry Laboratories (SSDLs) and Hospitals'. The report was well received and was distributed in a large number of copies to the members of the IAEA/WHO network of SSDLs and to medical physicists working with brachytherapy. The present report is an update of the aforementioned TECDOC. Whereas TECDOC-1079 described methods for calibrating brachytherapy sources with photon energies at or above those of 192 Ir, the current report has a wider scope in that it deals with standardization of calibration of all the most commonly used brachytherapy sources, including both photon and beta emitting sources. The latter sources have been in use for a few decades already, but their calibration methods have been unclear. Methods are also described for calibrating sources used in the rapidly growing field of cardiovascular angioplasty. In this application, irradiation of the vessel wall is done in an attempt to prevent restenosis after

Can knowledge exchange support the implementation of a health-promoting schools approach? Perceived outcomes of knowledge exchange in the COMPASS study.

Science.gov (United States)

Brown, Kristin M; Elliott, Susan J; Robertson-Wilson, Jennifer; Vine, Michelle M; Leatherdale, Scott T

2018-03-13

Despite the potential population-level impact of a health-promoting schools approach, schools face challenges in implementation, indicating a gap between school health research and practice. Knowledge exchange provides an opportunity to reduce this gap; however, there has been limited evaluation of these initiatives. This research explored researchers' and knowledge users' perceptions of outcomes associated with a knowledge exchange initiative within COMPASS, a longitudinal study of Canadian secondary students and schools. Schools received annual tailored summaries of their students' health behaviours and suggestions for action and were linked with knowledge brokers to support them in taking action to improve student health. Qualitative semi-structured interviews were conducted with COMPASS researchers (n = 13), school staff (n = 13), and public health stakeholders (n = 4) to explore their experiences with COMPASS knowledge exchange. Key issues included how knowledge users used school-specific findings, perceived outcomes of knowledge exchange, and suggestions for change. Outcomes for both knowledge users and researchers were identified; interestingly, knowledge users attributed more outcomes to using school-specific findings than knowledge brokering. School and public health participants indicated school-specific findings informed their programming and planning. Importantly, knowledge exchange provided a platform for partnerships between researchers, schools, and public health units. Knowledge brokering allowed researchers to gain feedback from knowledge users to enhance the study and a better understanding of the school environment. Interestingly, COMPASS knowledge exchange outcomes aligned with Samdal and Rowling's eight theory-driven implementation components for health-promoting schools. Hence, knowledge exchange may provide a mechanism to help schools implement a health-promoting schools approach. This research contributes to the limited

78 FR 23806 - Self-Regulatory Organizations; Miami International Securities Exchange LLC; Notice of Filing and...

Science.gov (United States)

2013-04-22

... participants the ability to utilize an order type that does not route to other exchanges. Specifically, the Do... Exchange is proposing to charge the same rate for transactions in Mini Options, $0.004 per contract, since..., the Exchange feels that it is appropriate to charge the ORF at the same rate as the standard option...

XTCE: XML Telemetry and Command Exchange Tutorial, XTCE Version 1

Science.gov (United States)

Rice, Kevin; Kizzort, Brad

2008-01-01

These presentation slides are a tutorial on XML Telemetry and Command Exchange (XTCE). The goal of XTCE is to provide an industry standard mechanism for describing telemetry and command streams (particularly from satellites.) it wiill lower cost and increase validation over traditional formats, and support exchange or native format.XCTE is designed to describe bit streams, that are typical of telemetry and command in the historic space domain.

Impact of airway gas exchange on the multiple inert gas elimination technique: theory.

Science.gov (United States)

Anderson, Joseph C; Hlastala, Michael P

2010-03-01

The multiple inert gas elimination technique (MIGET) provides a method for estimating alveolar gas exchange efficiency. Six soluble inert gases are infused into a peripheral vein. Measurements of these gases in breath, arterial blood, and venous blood are interpreted using a mathematical model of alveolar gas exchange (MIGET model) that neglects airway gas exchange. A mathematical model describing airway and alveolar gas exchange predicts that two of these gases, ether and acetone, exchange primarily within the airways. To determine the effect of airway gas exchange on the MIGET, we selected two additional gases, toluene and m-dichlorobenzene, that have the same blood solubility as ether and acetone and minimize airway gas exchange via their low water solubility. The airway-alveolar gas exchange model simulated the exchange of toluene, m-dichlorobenzene, and the six MIGET gases under multiple conditions of alveolar ventilation-to-perfusion, VA/Q, heterogeneity. We increased the importance of airway gas exchange by changing bronchial blood flow, Qbr. From these simulations, we calculated the excretion and retention of the eight inert gases and divided the results into two groups: (1) the standard MIGET gases which included acetone and ether and (2) the modified MIGET gases which included toluene and m-dichlorobenzene. The MIGET mathematical model predicted distributions of ventilation and perfusion for each grouping of gases and multiple perturbations of VA/Q and Qbr. Using the modified MIGET gases, MIGET predicted a smaller dead space fraction, greater mean VA, greater log(SDVA), and more closely matched the imposed VA distribution than that using the standard MIGET gases. Perfusion distributions were relatively unaffected.

Heat exchanger. [Nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Molina, C; Brisseaux, A

1976-01-19

This invention concerns a heat exchanger between a fluid flowing through a tube and a gas. Such an exchanger can be used, inter alia, for removing calories that cannot be used for generating electricity in a thermal or nuclear power station. This exchanger can withstand any pressure surges in the system and even the use of a high vapour pressure coolant such as ammonia, since the fluid flows in a round tube with low pressure drops (both with respect to the fluid to be cooled and the cooling air). It is rigid enough to stand up to being moved and handled as well as to gusts of wind. It is formed of units that can be handled without difficulty and that are easily dismantable and interchangeable, even in service, and it is easily maintained. The exchange area is high for a minimum frontal area and this enables the size of the supporting frame to be reduced and makes it easy to hide it behind a screen of trees should this prove necessary. Finally, it is composed of a small number of standard units thus reducing the industrial production cost. These units are rectangular plates, each one being a flat tubular coil fitted between two flat parallel sheet metal plates having on their outer sides flat top raised bosses. These units are assembled together by the tops of the bosses so as to form an exchanger bank, each bank comprising two collectors to which the bank coils are tightly connected.

Critical Review of Commercial Secondary Lithium-Ion Battery Safety Standards

Science.gov (United States)

Jones, Harry P.; Chapin, Thomas, J.; Tabaddor, Mahmod

2010-09-01

The development of Li-ion cells with greater energy density has lead to safety concerns that must be carefully assessed as Li-ion cells power a wide range of products from consumer electronics to electric vehicles to space applications. Documented field failures and product recalls for Li-ion cells, mostly for consumer electronic products, highlight the risk of fire, smoke, and even explosion. These failures have been attributed to the occurrence of internal short circuits and the subsequent thermal runaway that can lead to fire and explosion. As packaging for some applications include a large number of cells, the risk of failure is likely to be magnified. To address concerns about the safety of battery powered products, safety standards have been developed. This paper provides a review of various international safety standards specific to lithium-ion cells. This paper shows that though the standards are harmonized on a host of abuse conditions, most lack a test simulating internal short circuits. This paper describes some efforts to introduce internal short circuit tests into safety standards.

Structure-dependent degradation of polar compounds in weathered oils observed by atmospheric pressure photo-ionization hydrogen/deuterium exchange ultrahigh resolution mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Islam, Ananna; Kim, Donghwi [Kyungpook National University, Department of Chemistry, Daegu 702-701 (Korea, Republic of); Yim, Un Hyuk; Shim, Won Joon [Oil and POPs Research Group, Korea Institute of Ocean Science and Technology, KIOST, Geoje 656-834 (Korea, Republic of); Kim, Sunghwan, E-mail: sunghwank@knu.ac.kr [Kyungpook National University, Department of Chemistry, Daegu 702-701 (Korea, Republic of); Green Nano Center, Department of Chemistry, Daegu 702-701 (Korea, Republic of)

2015-10-15

Highlights: • We examined source crude oil and weathered oils from M/V Hebei accident. • APPI hydrogen/deuterium exchange ultrahigh mass spectrometry was applied. • N{sub 1} class compounds with 2° and/or 3° amine decrease in larger scale than pyridines. • Preferential degradation of nitrogen-containing compounds was confirmed. • Significant increase in S{sub 1}O{sub 1} compounds was observed as the weathering proceeds. - Abstract: The resin fractions of fresh mixtures of three oils spilled during the M/V Hebei Spirit oil spill, as well as weathered oils collected at weathering stages II and IV from the oil spill site were analyzed and compared by atmospheric pressure photo-ionization hydrogen/deuterium exchange mass spectrometry (HDX MS). The significantly decreased abundance of N{sup +}· and [N − H + D]{sup +} ions suggested that secondary and tertiary amine-containing compounds were preferentially degraded during the early stage of weathering. [N + H]{sup +} and [N + D]{sup +} ions previously attributed to pyridine-type compounds degraded more slowly than secondary and tertiary amine-containing compounds. The preferential degradation of nitrogen-containing compounds was confirmed by photo-degradation experiments using 15 standard compounds. In addition, significant increases of [S{sub 1}O{sub 1} + H]{sup +} and [S{sub 1}O{sub 1} + D]{sup +} ions with higher DBE values were observed from fresh oil mixtures as compared to stages II and IV samples, and that could be linked with the decrease of higher DBE compounds of the S{sub 1} class. This study presented convincing arguments and evidence demonstrating that secondary and tertiary amines were more vulnerable to photo-degradation than compounds containing pyridine, and hence, preferential degradation depending on chemical structures must be considered in the production of hazardous or toxic components.

Structure-dependent degradation of polar compounds in weathered oils observed by atmospheric pressure photo-ionization hydrogen/deuterium exchange ultrahigh resolution mass spectrometry

International Nuclear Information System (INIS)

Islam, Ananna; Kim, Donghwi; Yim, Un Hyuk; Shim, Won Joon; Kim, Sunghwan

2015-01-01

Highlights: • We examined source crude oil and weathered oils from M/V Hebei accident. • APPI hydrogen/deuterium exchange ultrahigh mass spectrometry was applied. • N 1 class compounds with 2° and/or 3° amine decrease in larger scale than pyridines. • Preferential degradation of nitrogen-containing compounds was confirmed. • Significant increase in S 1 O 1 compounds was observed as the weathering proceeds. - Abstract: The resin fractions of fresh mixtures of three oils spilled during the M/V Hebei Spirit oil spill, as well as weathered oils collected at weathering stages II and IV from the oil spill site were analyzed and compared by atmospheric pressure photo-ionization hydrogen/deuterium exchange mass spectrometry (HDX MS). The significantly decreased abundance of N + · and [N − H + D] + ions suggested that secondary and tertiary amine-containing compounds were preferentially degraded during the early stage of weathering. [N + H] + and [N + D] + ions previously attributed to pyridine-type compounds degraded more slowly than secondary and tertiary amine-containing compounds. The preferential degradation of nitrogen-containing compounds was confirmed by photo-degradation experiments using 15 standard compounds. In addition, significant increases of [S 1 O 1 + H] + and [S 1 O 1 + D] + ions with higher DBE values were observed from fresh oil mixtures as compared to stages II and IV samples, and that could be linked with the decrease of higher DBE compounds of the S 1 class. This study presented convincing arguments and evidence demonstrating that secondary and tertiary amines were more vulnerable to photo-degradation than compounds containing pyridine, and hence, preferential degradation depending on chemical structures must be considered in the production of hazardous or toxic components

Succeeding at teaching secondary mathematics your first year

CERN Document Server

Roddick, Cheryl D

2010-01-01

This practical resource helps beginning secondary mathematics teachers design a curriculum that is meaningful, differentiate instruction, engage students, meet standards, assess student understanding, and more.

Accurate orbital-dependent correlation and exchange-correlation potentials from non-iterative ab initio dft calculations

Science.gov (United States)

Grabowski, Ireneusz; Lotrich, Victor

2005-08-01

A new approximate non-iterative procedure to obtain accurate correlation and exchange-correlation potentials of Kohn-Sham (KS) density functional theory (DFT) is presented. By carrying out only one step of the correlated optimized effective potential (OEP) iterations following the standard iterative exchange-only OEP, one can recover accurate correlation potentials corresponding to the orbital-dependent second-order many-body perturbation theory [MBPT(2)] energy functional that are hardly discernible from those obtained by the more expensive, fully iterative procedure. This new 'one-step' OEP-MBPT(2) algorithm reflects the non-iterative, perturbative algorithm of standard, canonical MBPT(2) of ab initio wave function theory, while it allows the correlation potentials to readjust and include the majority of the MBPT(2) correlation effect. It is also flexible in the treatment of exchange and the Hartree-Fock orbitals may be used in lieu of the exchange-only OEP orbitals, when the correlation or exchange-correlation potential is of interest.

40 CFR 421.316 - Pretreatment standards for new sources.

Science.gov (United States)

2010-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tungsten and Cobalt... 87.800 (k) Cobalt hydroxide filter cake wash. PSNS for the Secondary Tungsten and Cobalt Subcategory...

40 CFR 421.245 - Pretreatment standards for existing sources.

Science.gov (United States)

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Nickel... Nickel 9.590 6.344 (c) Acid reclaim leaching belt filter backwash PSES for the Secondary Nickel...

Non-equilibrium hydrogen exchange for determination of H-bond strength and water accessibility in solid proteins.

Science.gov (United States)

Grohe, Kristof; Movellan, Kumar Tekwani; Vasa, Suresh Kumar; Giller, Karin; Becker, Stefan; Linser, Rasmus

2017-05-01

We demonstrate measurement of non-equilibrium backbone amide hydrogen-deuterium exchange rates (HDX) for solid proteins. The target of this study are the slowly exchanging residues in solid samples, which are associated with stable secondary-structural elements of proteins. These hydrogen exchange processes escape methods measuring equilibrium exchange rates of faster processes. The method was applied to a micro-crystalline preparation of the SH3 domain of chicken α-spectrin. Therefore, from a 100% back-exchanged micro-crystalline protein preparation, the supernatant buffer was exchanged by a partially deuterated buffer to reach a final protonation level of approximately 20% before packing the sample in a 1.3 mm rotor. Tracking of the HN peak intensities for 2 weeks reports on site-specific hydrogen bond strength and also likely reflects water accessibility in a qualitative manner. H/D exchange can be directly determined for hydrogen-bonded amides using 1 H detection under fast magic angle spinning. This approach complements existing methods and provides the means to elucidate interesting site-specific characteristics for protein functionality in the solid state.

The role of Polish Secondary Standard Dosimetry Laboratory in view of the requirements of the EC Directive 97/43 EURATOM

International Nuclear Information System (INIS)

Gwiazdowska, B.; Bulski, W.

2004-01-01

The aim of this paper is to present the history and experience of the Polish SSDL (Secondary Standard Dosimetry Laboratory). It also presents the propositions in the domain of quality assurance in radiotherapy in Poland, as fulfilling the requirements of the Directive 97/43 EURATOM on health protection of individuals against the dangers of ionizing radiation in relation to medical exposure, which is obligatory for the countries of the European Union. It has been pointed out that there are, among other provisions, two concepts concerning the quality assurance in application of radiation in medicine, mentioned by the Directive, a) inspection and b) clinical audit, which should be implemented by the Member States. In the process of establishing and implementing the Directive confusion may appear as to the difference between the two concepts of external audits. The role of the SSDLs in carrying out external dosimetry audits is presented. The history of the establishment of the Polish SSDL (Secondary Standard Dosimetry Laboratory) and its inclusion into the international network of laboratories coordinated by the International Atomic Energy Agency and the World Health Organization is presented as well as the resulting advantages, obligations and perspectives for further activities. The main activities of the Polish have been presented, namely maintaining a data-base on the radiotherapy infrastructure in Poland, preparation of recommendations on dosimetry procedures and quality control, calibration of dosimeters, external postal quality audits of dosimetry, etc. These activities are illustrated with the results from the period 1991-2003. Based on the solutions and results presented in this paper, the authors conclude that the Ministry of Health should grant the Polish SSDL with a suitable legal status for carrying out external audits nationwide, especially since, according to the Directive 97/43, clinical audits in radiotherapy have to include dosimetry audits. (author)

40 CFR 421.315 - Pretreatment standards for existing sources.

Science.gov (United States)

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tungsten....346 68.543 Tungsten 197.1 87.8 (k) Cobalt hydroxide filter cake wash. PSES for the Secondary Tungsten...

Experimental observation of thermal-hydraulic behavior in PCCS horizontal heat exchanger

International Nuclear Information System (INIS)

Kondo, Masaya; Nakamura, Hideo; Yamamoto, Kazuhiko; Shimada, Rumi; Tokuma, Hideaki

2003-01-01

A series of thermal-hydraulic experiments have been performed using a prototypical-scale experimental facility simulating a horizontal heat exchanger of a Passive Containment Cooling System (PCCS) for next generation BWRs. The influences of multi-dimensional boiling flow in secondary water pool on primary flow in parallel tubes are investigated. The experimental results at postulated accident conditions; 0.7 MPa, steam flow rate equivalent to 1% core power with 1% non-condensable gas, show that steam condensation completes in almost the same heat transfer length in all the instrumented tubes. The secondary heat transfer coefficient is relatively small at the lower portion in the tube bundle when the flow regime is bubbly flow, and increases with elevation as the flow regime turns into churn-like flow. The primary steam flow distribution among tubes is rather insensitive to such a variation in the secondary heat transfer coefficient, since the contribution of the secondary heat transfer to the local heat resistance is 30% or less at postulated accident conditions. The influence of steam flow rate is insensitive too, while the contribution of the secondary heat transfer coefficient increases at low pressure conditions. (author)

EVALUASI KINERJA HEAT EXCHANGER DENGAN METODE FOULING F

Directory of Open Access Journals (Sweden)

Bambang Setyoko

2012-02-01

Full Text Available The performance of heat exchangers usually deteriorates with time as a result of accumulation of depositson heat transfer surfaces. The layer of deposits represents additional resistance to heat transfer and causesthe rate of heat transfer in a heat exchanger to decrease. The net effect of these accumulations on heattransfer is represented by a fouling factor Rf , which is a measure of the thermal resistance introduced byfouling.In this case, the type of fouling is the precipitation of solid deposits in a fluid on the heat transfer surface.The mineral deposits forming on the inner and the outer surfaces of fine tubes in the heat exchanger. Thefouling factor is increases with time as the solid deposits build up on the heat exchanger surface. Foulingincreases with increasing temperature and decreasing velocity.In this research, we obtain the coefisien clean overal 5,93 BTU/h.ft2.oF, Dirt factor 0,004 BTU/h.ft2 0F,Pressure drope in tube 2,84 . 10-3 Psi and pressure drope in shell 4,93 . 10-4 Psi.This result are less thanthe standard of parameter. Its means this Heat exchanger still clean relativity and can operate continousslywithout cleaning.

Standards for electronic imaging for graphic arts systems

Science.gov (United States)

Dunn, S. T.; Dunn, Patrice M.

1991-03-01

This paper examines the development of electronic imaging standards by and for the graphic arts industry. Taken collectively this body of work is referred to as Digital Data Exchange Standards (DDES). Because these standards are being driven by market and user requirements there are several fundamental guiding principles to their development. This paper examines these and provides an overview to the technical developments undertaken by the accredited graphic arts industry standards committees to date.

CSI 3.0: a web server for identifying secondary and super-secondary structure in proteins using NMR chemical shifts.

Science.gov (United States)

Hafsa, Noor E; Arndt, David; Wishart, David S

2015-07-01

The Chemical Shift Index or CSI 3.0 (http://csi3.wishartlab.com) is a web server designed to accurately identify the location of secondary and super-secondary structures in protein chains using only nuclear magnetic resonance (NMR) backbone chemical shifts and their corresponding protein sequence data. Unlike earlier versions of CSI, which only identified three types of secondary structure (helix, β-strand and coil), CSI 3.0 now identifies total of 11 types of secondary and super-secondary structures, including helices, β-strands, coil regions, five common β-turns (type I, II, I', II' and VIII), β hairpins as well as interior and edge β-strands. CSI 3.0 accepts experimental NMR chemical shift data in multiple formats (NMR Star 2.1, NMR Star 3.1 and SHIFTY) and generates colorful CSI plots (bar graphs) and secondary/super-secondary structure assignments. The output can be readily used as constraints for structure determination and refinement or the images may be used for presentations and publications. CSI 3.0 uses a pipeline of several well-tested, previously published programs to identify the secondary and super-secondary structures in protein chains. Comparisons with secondary and super-secondary structure assignments made via standard coordinate analysis programs such as DSSP, STRIDE and VADAR on high-resolution protein structures solved by X-ray and NMR show >90% agreement between those made with CSI 3.0. © The Author(s) 2015. Published by Oxford University Press on behalf of Nucleic Acids Research.

Analysis of secondary motions in square duct flow

Science.gov (United States)

Modesti, Davide; Pirozzoli, Sergio; Orlandi, Paolo; Grasso, Francesco

2018-04-01

We carry out direct numerical simulations (DNS) of square duct flow spanning the friction Reynolds number range {Re}τ * =150-1055, to study the nature and the role of secondary motions. We preliminarily find that secondary motions are not the mere result of the time averaging procedure, but rather they are present in the instantaneous flow realizations, corresponding to large eddies persistent in both space and time. Numerical experiments have also been carried out whereby the secondary motions are suppressed, hence allowing to quantifying their effect on the mean flow field. At sufficiently high Reynolds number, secondary motions are found to increase the friction coefficient by about 3%, hence proportionally to their relative strength with respect to the bulk flow. Simulations without secondary motions are found to yield larger deviations on the mean velocity profiles from the standard law-of-the-wall, revealing that secondary motions act as a self-regulating mechanism of turbulence whereby the effect of the corners is mitigated.

Activities of Radiation Standard Section

International Nuclear Information System (INIS)

Kannan, A.; Rao, P.S.; Sachadev, R.N.; Shaha, V.V.; Sharma, D.; Srivastava, P.K.

1992-01-01

A brief account of the various facilities and services provided by the Radiation Standards Section (RSS) of the Bhabha Atomic Research Centre, Bombay is given. RSS maintains the primary and secondary standards of various parameters of radiation measurements. It ensures accurate radiological measurements as per international requirements, through periodic international intercomparisons of national standards. It also provides calibration services to various users of radiation sources and instruments. The activities of RSS are described under the headings: (1) Radiological Metrology Standards, (2) Radionuclide Standards, Neutron Metrology, (4) Instruments Calibration, (5) Non-ionizing Radiations, and (6) Instrumentation. (author). figs., tabs

Role of Dividend of Power to Buy Shares in Companies in Indonesia Stock Exchange

Directory of Open Access Journals (Sweden)

Iskandar Muda

2017-06-01

Full Text Available This study aims to determine the role of the Purchasing Power Shares on manufacturing companies in Indonesia Stock Exchange Period 2014-2015. The variables used in this study as an Independent Variable Dividend and Purchasing Power Shares as Dependent Variables. Power Buy Stocks in this study was measured by the volume of stock sales every year. This research was conducted in Manufacturing company listed on the Indonesia Stock Exchange. The population of this study were 144 companies with purposive sampling as many as 19 of the Company's Manufacturing Company listed on the Indonesia Stock Exchange with the study of the 2014-2015 period in order to obtain 38 units of analysis. Data of this research are secondary data from the financial statements of 19 companies published in the Indonesia Stock Exchange. This research data processing method using the Test Statistics Deskribtif, Classical Assumption Test, Test Linear Regression using SPSS. The results of this study demonstrate that the role of the Dividend has significant influence on the Purchasing Power Shares in Manufacturing Company in Indonesia Stock Exchange (BEI.

Leaching of 60 Co and 137 Cs from spent ion exchange resins in ...

Indian Academy of Sciences (India)

Cement; radioactive waste; composite; waste management. Abstract. The leaching rate of 60Co and 137Cs from the spent cation exchange resins in cement–bentonite matrix has been studied. The solidification matrix was a standard Portland cement mixed with 290–350 (kg/m3) spent cation exchange resins, with or ...

Performance of Secondary School Students in Maiduguri, Nigeria in ...

African Journals Online (AJOL)

Performance of Secondary School Students in Maiduguri, Nigeria in the Community Screening Instrument for Dementia. ... Impairment was operationally defined by at least one score two standard deviations below the normative mean for a given test or two or more test scores at least one standard deviation below the mean.

40 CFR 421.244 - Standards of performance for new sources.

Science.gov (United States)

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Nickel... all times. (c) Acid reclaim leaching belt filter backwash. NSPS for the Secondary Nickel Subcategory...

77 FR 31680 - Self-Regulatory Organizations; International Securities Exchange, LLC; Notice of Filing and...

Science.gov (United States)

2012-05-29

... Organizations; International Securities Exchange, LLC; Notice of Filing and Immediate Effectiveness of Proposed Rule Change To Amend the Qualification Standards for Market Makers To Receive a Rebate May 22, 2012...-4 thereunder,\\2\\ notice is hereby given that on May 15, 2012, the International Securities Exchange...

17 CFR 155.6 - Trading standards for the transaction of business on registered derivatives transaction execution...

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Trading standards for the transaction of business on registered derivatives transaction execution facilities. 155.6 Section 155.6 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION TRADING STANDARDS § 155.6 Trading...

Foreign Exchange Reserves and the Reserve Bank’s Balance Sheet

OpenAIRE

Christian Vallence

2012-01-01

The Reserve Bank of Australia holds and manages the nation’s foreign exchange reserve assets in order to meet its policy objectives. While Australia’s foreign exchange reserves are relatively modest by international standards, they nonetheless constitute a sizeable portion of the Bank’s balance sheet, and variations in the Australian dollar value of these reserves are usually the most volatile component of the Bank’s profit and loss statement. This article discusses some of the key decisions ...

IAEA fundamental standards for protection against radiation

International Nuclear Information System (INIS)

1981-01-01

The Governor's Counsel of the IAEA has just approved the revision of existing norms, previously prepared in cooperation with the ILO, WHO and OECD. The revised norms represent a great advance in the efforts to reduce risks for which there is no threshold value. A further initiative of the IAEA is the program of radiation protection standards for nuclear power stations. They form the first international instructions for a normalised basis of safety in nuclear power stations. The need for exchange of information was emphasised at the International Conference in Stockholm in 1980. The existing safety norms were considered adequate at the time. The IAEA activities in the field of standards, advice and technical help, exchange of information and training and emergency planning are also mentioned. (Auth.)

Standardized cardiovascular data for clinical research, registries, and patient care: a report from the Data Standards Workgroup of the National Cardiovascular Research Infrastructure project.

Science.gov (United States)

Anderson, H Vernon; Weintraub, William S; Radford, Martha J; Kremers, Mark S; Roe, Matthew T; Shaw, Richard E; Pinchotti, Dana M; Tcheng, James E

2013-05-07

Relatively little attention has been focused on standardization of data exchange in clinical research studies and patient care activities. Both are usually managed locally using separate and generally incompatible data systems at individual hospitals or clinics. In the past decade there have been nascent efforts to create data standards for clinical research and patient care data, and to some extent these are helpful in providing a degree of uniformity. Nonetheless, these data standards generally have not been converted into accepted computer-based language structures that could permit reliable data exchange across computer networks. The National Cardiovascular Research Infrastructure (NCRI) project was initiated with a major objective of creating a model framework for standard data exchange in all clinical research, clinical registry, and patient care environments, including all electronic health records. The goal is complete syntactic and semantic interoperability. A Data Standards Workgroup was established to create or identify and then harmonize clinical definitions for a base set of standardized cardiovascular data elements that could be used in this network infrastructure. Recognizing the need for continuity with prior efforts, the Workgroup examined existing data standards sources. A basic set of 353 elements was selected. The NCRI staff then collaborated with the 2 major technical standards organizations in health care, the Clinical Data Interchange Standards Consortium and Health Level Seven International, as well as with staff from the National Cancer Institute Enterprise Vocabulary Services. Modeling and mapping were performed to represent (instantiate) the data elements in appropriate technical computer language structures for endorsement as an accepted data standard for public access and use. Fully implemented, these elements will facilitate clinical research, registry reporting, administrative reporting and regulatory compliance, and patient care

STEP - Product Model Data Sharing and Exchange

DEFF Research Database (Denmark)

Kroszynski, Uri

1998-01-01

During the last fifteen years, a very large effort to standardize the product models employed in product design, manufacturing and other life-cycle phases has been undertaken. This effort has the acronym STEP, and resulted in the International Standard ISO-10303 "Industrial Automation Systems...... - Product Data Representation and Exchange", featuring at present some 30 released parts, and growing continuously. Many of the parts are Application Protocols (AP). This article presents an overview of STEP, based upon years of involvement in three ESPRIT projects, which contributed to the development...

Severe iron intoxication treated with exchange transfusion

DEFF Research Database (Denmark)

Carlsson, M; Cortes, D; Jepsen, S

2009-01-01

An 18-month-old previous healthy girl who had ingested 442 mg elemental iron/kg was admitted to a paediatric intensive care unit. The child was treated with gastric lavage, whole bowel irrigation and intravenous deferoxamine. After 2 h of standard therapy serum iron had risen threefold to 1362 µg....../dl (244 µmol/l). The child was treated with exchange transfusion (ET; 52 ml/kg) and serum iron fell to 134 µg/dl (24 µmol/l). The patient made an uncomplicated recovery. ET should be considered in severe iron poisoning when standard therapy is inadequate....

Disciplining standard-setting : Which approach to choose (if any)?

NARCIS (Netherlands)

Kanevskaia, Olia; Jacobs, Kai; Blind, Knut

In the world of continuous globalization, standards play a crucial role in transnational economic development. Being the drivers of harmonization and innovation, standards do not only facilitate production and exchange in goods and services, but also carry significant policy implications and create

Disciplining standard-setting : Which approach to choose (if any)

NARCIS (Netherlands)

Kanevskaia, Olia

2017-01-01

In the world of continuous globalization, standards play a crucial role in transnational economic development. Being the drivers of harmonization and innovation, standards do not only facilitate production and exchange in goods and services, but also carry significant policy implications and create

Photochemical exchange reactions of thymine, uracil and their nucleosides with selected amino acids

International Nuclear Information System (INIS)

Shetlar, M.D.; Taylor, J.A.; Hom, K.

1984-01-01

The photoinduced exchange reactions of thymine with lysine at basic pH, using 254 nm light, have been studied. Three products have been isolated, namely, 6-amino-2-(1-thyminyl)hexanoic acid (Ia), 2-amino-6-(1-thyminyl)hexanoic acid (IIa) and 1-amino-5-(1-thyminyl)pentane (IIIa). Compound IIIa was shown to be a secondary product, produced by photochemical decarboxylation of Ia. Photochemical reaction of thymine with glycine and alanine at basic pH led, respectively, to formation of 2-(1-thyminyl)acetic acid (Ic) and 2-(1-thyminyl)propionic acid (Id). Compounds Ic and Id underwent photolysis to produce the decarboxylated secondary products 1-methylthymine and 1-ethylthymine, respectively. Thymidine reacts photochemically with glycine and alanine to produce the same products. Irradiation of DNA in the presence of lysine at basic pH led to the formation of the same products formed in the thymine-lysine system, namely Ia, IIa and IIIa. Uracil was found to undergo analogous photochemical exchange reactions with lysine to form 6-amino-2-(1-uracilyl)hexanoic acid (Ib), and 2-amino-6-(1-uracilyl)hexanoic acid (IIb). Compound Ib was found to undergo photodecarboxylation to form 1-amino-5-(1-uracilyl)pentane (IIIb), analogous to the secondary photoreaction of Ia. Photoreaction of uracil with 1,5-diaminopentane (cadaverine) likewise led to formation of IIIb. (author)

An assessment of Mathematics self – efficacy of secondary school ...

African Journals Online (AJOL)

The study examined an assessment of mathematics self-efficacy of secondary school students in Osun State. It drawn on 500 students comprising 250 males and 250 females randomly selected from 5 secondary schools in Osogbo. Their ages range between 11-17 years with a mean age of 14 years and a standard ...

Standard interfaces for program-modular multiprocessor systems

International Nuclear Information System (INIS)

Chernykh, E.V.

1982-01-01

The peculiarities of the structures of existing and developed standard interfaces used in automation systems for nuclear physical experiments are considered. general structural characteristics of multiprocessor system interfaces are revealed. The comparison of the existing system CAMAC crate and designed standards of COMPEX, E3S and FASTBUS interfaces by capacity and relative cost is carried out. The analysis of the given data shows that operation of any interface is more advantageous at the rates close to capacity values, the relative cost being minimum. In this case the advantage is on the side of interfaces with greater capacity values for which at a moderated decrease of the exchange or requests processing rate the relative costs grow slower. A higher capacity of one-cycle exchange is provided with functional data way specialization in the interface. The conclusion is drawn that most perspective trend in the development of automation systems for high energy physics experiments is using FASTBUS standard

A standard-enabled workflow for synthetic biology

KAUST Repository

Myers, Chris J.

2017-06-15

A synthetic biology workflow is composed of data repositories that provide information about genetic parts, sequence-level design tools to compose these parts into circuits, visualization tools to depict these designs, genetic design tools to select parts to create systems, and modeling and simulation tools to evaluate alternative design choices. Data standards enable the ready exchange of information within such a workflow, allowing repositories and tools to be connected from a diversity of sources. The present paper describes one such workflow that utilizes, among others, the Synthetic Biology Open Language (SBOL) to describe genetic designs, the Systems Biology Markup Language to model these designs, and SBOL Visual to visualize these designs. We describe how a standard-enabled workflow can be used to produce types of design information, including multiple repositories and software tools exchanging information using a variety of data standards. Recently, the ACS Synthetic Biology journal has recommended the use of SBOL in their publications.

Effect of Liquid/Vapour Maldistribution on the Performance of Plate Heat Exchanger Evaporators

DEFF Research Database (Denmark)

Jensen, Jonas Kjær; Kærn, Martin Ryhl; Ommen, Torben Schmidt

2015-01-01

Plate heat exchangers are often applied as evaporators in industrial refrigeration and heat pump systems. In the design and modelling of such heat exchangers the flow and liquid/vapour distribution is often assumed to be ideal. However, maldistribution may occur and will cause each channel...... to behave differently due to the variation of the mass flux and vapour quality. To evaluate the effect of maldistribution on the performance of plate heat exchangers, a numerical model is developed in which the mass, momentum and energy balances are applied individually to each channel, including suitable...... correlations for heat transfer and pressure drop. The flow distribution on both the refrigerant and secondary side is determined based on equal pressure drop while the liquid/vapour distribution is imposed to the model. Results show that maldistribution may cause up to a 25 % reduction of the overall heat...

Effects of national accounting standards convergence to international accounting standards on foreign direct investment

Directory of Open Access Journals (Sweden)

Asieh Farazandehnia

2015-09-01

Full Text Available One of the most important factors on attracting foreign investors to invest on Tehran Stock Exchange is to have transparent accounting rules and regulations. When there are some consistency between national accounting standards and international accounting standards, we may, at least, expect foreign investors to have better understanding on financial statements. In 2006, there were some changes on Iranian national accounting standards in an attempt to make them closer to international accounting standards. In this study, we select the information of 153 firms five years before and after this regulation and study the effect of convergence from national accounting standards to international accounting standards on foreign direct investment. Using some statistical tests, the study has determined that there was no meaningful relationship between foreign direct investment before and after change on accounting standards. In addition, there was no difference on the information quality before and after change on accounting standards. However, there was some meaningful relationship between the information quality and foreign direct investment.

Heat Exchangers for Utilization of the Heat of High-Temperature Geothermal Brines

Science.gov (United States)

Alkhasov, A. B.; Alkhasova, D. A.

2018-03-01

The basic component of two-circuit geothermal systems is the heat exchanger. When used in geothermal power systems, conventional shell-and-tube and plate heat exchangers cause problems related to the cleaning of the latter from salt-deposition and corrosion products. Their lifetime does not exceed, as a rule, 1 year. To utilize the heat of high-temperature geothermal brines, a heat exchanger of the "tube-in-tube" type is proposed. A heat exchanger of this design has been operated for several years in Ternair geothermal steam field; in this heat exchanger, the thermal potential of the saline thermal water is transferred to the fresh water of the secondary circuit of the heating system for apartment houses. The reduction in the weight and size characteristics of the heat exchangers is a topical problem that can be solved with the help of heat transfer enhancers. To enhance the heat transfer process in the heat exchanger, longitudinal ribbing of the heat exchange surface is proposed. The increase in the heat exchange surface from the heat carrier side by ribbing results in an increase in the amount of the heat transferred from the heating agent. The heat exchanger is easy to manufacture and is assembled out of components comprised of two concentrically positioned tubes of a definite length, 3-6 m, serially connected with each other. The method for calculation of the impact of the number and the size of the longitudinal ribs on the heat transfer in the well heat exchanger is presented and a criterion for the selection of the optimal number and design parameters of the ribs is formulated. To prevent the corrosion and salt deposition in the heat exchanger, the use of an effective OEDFK (oxyethylidenediphosphonic acid) agent is proposed. This agent has a long-lasting corrosion-inhibiting and antiscaling effect, which is explained by the formation of a strongly adhesive chelate layer difficult to wash off the surface. The passivating OEDFK layer is restored by periodical

ASN.1 notation for exchange of data in computer-based railway control systems

Directory of Open Access Journals (Sweden)

Zbigniew ŁUKASIK

2009-01-01

Full Text Available Development of railway control systems aims at computerization. In most cases these systems are Distributed Real Time Systems. However, a huge problem in their putting into practice is the lack of interface standardization in the range of data structures and information exchange methods. It results in a variety of solutions, and thus in problems concerning cooperation of systems that come from different software vendors. Specification of protocols for data exchanging applications should therefore be created with the use of generally accepted standards. One of them is ASN.1 (Abstract Syntax Notation One language, which shall be presented in this article.

Magnetic Exchange Couplings from Semilocal Functionals Evaluated Nonself-Consistently on Hybrid Densities: Insights on Relative Importance of Exchange, Correlation, and Delocalization.

Science.gov (United States)

Phillips, Jordan J; Peralta, Juan E

2012-09-11

Semilocal functionals generally yield poor magnetic exchange couplings for transition-metal complexes, typically overpredicting in magnitude the experimental values. Here we show that semilocal functionals evaluated nonself-consistently on densities from hybrid functionals can yield magnetic exchange couplings that are greatly improved with respect to their self-consistent semilocal values. Furthermore, when semilocal functionals are evaluated nonself-consistently on densities from a "half-and-half" hybrid, their errors with respect to experimental values can actually be lower than those from self-consistent calculations with standard hybrid functionals such as PBEh or TPSSh. This illustrates that despite their notoriously poor performance for exchange couplings, for many systems semilocal functionals are capable of delivering accurate relative energies for magnetic states provided that their electron delocalization error is corrected. However, while self-consistent calculations with hybrids uniformly improve results for all complexes, evaluating nonself-consistently with semilocal functionals does not give a balanced improvement for both ferro- and antiferromagnetically coupled complexes, indicating that there is more at play with the overestimation problem than simply the delocalization error. Additionally, we show that for some systems the conventional wisdom of choice of exchange functional mattering more than correlation does not hold. This combined with results from the nonself-consistent calculations provide insight on clarifying the relative roles of exchange, correlation, and delocalization in calculating magnetic exchange coupling parameters in Kohn-Sham Density Functional Theory.

EFFECTIVENESS OF FOLK MATHEMATICS ON ACHIEVEMENT AT SECONDARY LEVEL STUDENT

OpenAIRE

Mrs. K. K. Sumathi

2016-01-01

The present study is aimed at finding the effectiveness of folk mathematics on achievement at secondary level student. It was an experimental method conducted on secondary school students in teaching mathematics for seventh standard. The result concluded by the investigator was that the effect of folk mathematics was better than the traditional method of teaching.

CALINX (California Information Exchange): a multi-stakeholder statewide initiative to improve healthcare information flows.

Science.gov (United States)

Hopkins, D S; Oswald, N; McCaffrey, K; Bressler, S; Davidson, N; Vela, L

2000-01-01

Given the diffusion of responsibilities for gathering and reporting healthcare information in a managed care environment, California stakeholders are taking concrete steps to break the deadlock on data and information flows that has characterized the industry for some time. The California Information Exchange (CALINX) was established to facilitate the implementation of the Health Insurance Portability and Accountability Act (HIPAA) standards in California and to create trust for data exchange between trading partners, without which data exchange still will not occur. Strategic directions are set by the chief executives of key associations and organizations representing purchasers, plans, providers, and consumers. Multi-stakeholder workgroups have produced detailed data guidelines for the HIPAA standards along with rules for exchange of key data sets between trading partners. These rules address frequency, timeliness, and accuracy of data submission. Both the data guidelines and the rules have been tested in live demonstration projects, and the results of these projects have been reported to substantiate the business case for implementation. Further incentives are being built into contracts between purchasers and plans, and between plans and providers. CALINX is currently promoting widespread adoption of the data guidelines and rules for exchange with all members of the industry.

Standard interface files and procedures for reactor physics codes. Version IV

International Nuclear Information System (INIS)

O'Dell, R.D.

1977-09-01

Standards, procedures, and recommendations of the Committee on Computer Code Coordination for promoting the exchange of reactor physics codes are updated to Version IV status. Standards and procedures covering general programming, program structure, standard interface files, and file management and handling subroutines are included

Segmented heat exchanger

Science.gov (United States)

Baldwin, Darryl Dean; Willi, Martin Leo; Fiveland, Scott Byron; Timmons, Kristine Ann

2010-12-14

A segmented heat exchanger system for transferring heat energy from an exhaust fluid to a working fluid. The heat exchanger system may include a first heat exchanger for receiving incoming working fluid and the exhaust fluid. The working fluid and exhaust fluid may travel through at least a portion of the first heat exchanger in a parallel flow configuration. In addition, the heat exchanger system may include a second heat exchanger for receiving working fluid from the first heat exchanger and exhaust fluid from a third heat exchanger. The working fluid and exhaust fluid may travel through at least a portion of the second heat exchanger in a counter flow configuration. Furthermore, the heat exchanger system may include a third heat exchanger for receiving working fluid from the second heat exchanger and exhaust fluid from the first heat exchanger. The working fluid and exhaust fluid may travel through at least a portion of the third heat exchanger in a parallel flow configuration.

Thermal Sizing of Heat Exchanger Tubes for Air Natural Convective Cooling System of Emergency Cooling Tank

Energy Technology Data Exchange (ETDEWEB)

Kim, Myoung Jun; Lee, Hee Joon [Kookmin Univ., Seoul (Korea, Republic of); Moon, Joo Hyung; Bae, Youngmin; Kim, Youngin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

For the long operation of secondary passive cooling system, however, water level goes down by evaporation in succession at emergency cooling tank. At the end there would be no place to dissipate heat from condensation heat exchanger. Therefore, steam cooling heat exchanger is put on the top of emergency cooling tank to maintain appropriate water level by collecting evaporating steam. Steam cooling heat exchanger is installed inside an air chimney and evaporated steam is cooled down by air natural convection. In this study, thermal sizing of steam cooling heat exchanger under air natural convection was conducted by TSCON program for the design of experimental setup as shown in Fig. 2. Thermal sizing of steam cooling heat exchanger tube under air natural convection was conducted by TSCON program for the design of experimental setup. 25 - 1' tubes which has a length 1687 mm was determined as steam cooling heat exchanger at 2 kW heat load and 100 liter water pool in emergency cooling tank (experimental limit condition). The corresponding width of two tubes is 50 mm and has 5 by 5 tube array for heat exchanger.

Thermal Sizing of Heat Exchanger Tubes for Air Natural Convective Cooling System of Emergency Cooling Tank

International Nuclear Information System (INIS)

Kim, Myoung Jun; Lee, Hee Joon; Moon, Joo Hyung; Bae, Youngmin; Kim, Youngin

2014-01-01

For the long operation of secondary passive cooling system, however, water level goes down by evaporation in succession at emergency cooling tank. At the end there would be no place to dissipate heat from condensation heat exchanger. Therefore, steam cooling heat exchanger is put on the top of emergency cooling tank to maintain appropriate water level by collecting evaporating steam. Steam cooling heat exchanger is installed inside an air chimney and evaporated steam is cooled down by air natural convection. In this study, thermal sizing of steam cooling heat exchanger under air natural convection was conducted by TSCON program for the design of experimental setup as shown in Fig. 2. Thermal sizing of steam cooling heat exchanger tube under air natural convection was conducted by TSCON program for the design of experimental setup. 25 - 1' tubes which has a length 1687 mm was determined as steam cooling heat exchanger at 2 kW heat load and 100 liter water pool in emergency cooling tank (experimental limit condition). The corresponding width of two tubes is 50 mm and has 5 by 5 tube array for heat exchanger

78 FR 54069 - Patient Protection and Affordable Care Act; Program Integrity: Exchange, SHOP, and Eligibility...

Science.gov (United States)

2013-08-30

... Qualified Health Plans; Exchange Standards for Employers, 77 FR 18310 (March 27, 2012). \\2\\ Patient..., including States, health insurance issuers, consumer groups, agents and brokers, provider groups, Members of....120(c) to Exchange consumer assistance entities, please see the recent final rule, Patient Protection...

Exchange rate rebounds after foreign exchange market interventions

Science.gov (United States)

Hoshikawa, Takeshi

2017-03-01

This study examined the rebounds in the exchange rate after foreign exchange intervention. When intervention is strongly effective, the exchange rate rebounds at next day. The effect of intervention is reduced slightly by the rebound after the intervention. The exchange rate might have been 67.12-77.47 yen to a US dollar without yen-selling/dollar-purchasing intervention of 74,691,100 million yen implemented by the Japanese government since 1991, in comparison to the actual exchange rate was 103.19 yen to the US dollar at the end of March 2014.

47 CFR 95.1509 - ASTM E2213-03 DSRC Standard.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false ASTM E2213-03 DSRC Standard. 95.1509 Section 95... ASTM E2213-03 DSRC Standard. On-Board Units operating in the 5850-5925 MHz band shall comply with the... Materials (ASTM) E2213-03, Standard Specification for Telecommunications and Information Exchange Between...

Limited and selective transfer of plasma membrane glycoproteins to membrane of secondary lysosomes

International Nuclear Information System (INIS)

Haylett, T.; Thilo, L.

1986-01-01

Radioactive galactose, covalently bound to cell surface glycoconjugates on mouse macrophage cells, P388D 1 , was used as a membrane marker to study the composition, and the kinetics of exchange, of plasma membrane-derived constituents in the membrane of secondary lysosomes. Secondary lysosomes were separated from endosomes and plasma membrane by self-forming Percoll density gradients. Horseradish peroxidase, taken up by fluid-phase pinocytosis, served as a vesicle contents marker to monitor transfer of endosomal contents into secondary lysosomes. Concurrently, the fraction of plasma membrane-derived label of secondary lysosomes increased by first order kinetics from 4 PAGE, labeled molecules of M/sub r/ 160-190 kD were depleted and of the M/sub r/ 100-120 kD were enriched in lysosome membrane compared with the relative composition of label on the cell surface. No corresponding selectivity was observed for the degradation of label, with all M/sub r/ classes being affected to the same relative extent. The results indicate that endocytosis-derived transfer of plasma membrane constitutents to secondary lysosomes is a limited and selective process, and that only ∼1% of internalized membrane is recycled via a membrane pool of secondary lysosomes

Relative mobility of 1-H atoms of carbohydrates in heterogeneous isotope exchange reactions

International Nuclear Information System (INIS)

Akulov, G.P.; Snetkova, E.V.; Kayumov, V.G.; Kaminskii, Yu.L.

1988-01-01

The method of competitive reactions was used to determine the relative mobilities of the 1-H atoms of carbohydrates in reactions of heterogeneous isotope exchange, using various reference standards, catalysts, and buffer systems. On the basis of the results obtained, the investigated carbohydrates are ranged in a series of decreasing mobility of the hydrogen atoms exchanged in heterogeneous isotope exchange reactions. It was demonstrated that the mobility of the 1-H atoms is related to the concentration of the acyclic forms of the carbohydrates

Privacy and Confidentiality in Exchange of Information Procedures : Some Uncertainties, Many Issues, but Few Solutions

NARCIS (Netherlands)

Debelva, F.; Mosquera, Valderrama I.J.

2017-01-01

The overall aim of this article is to analyse the taxpayers’ rights to confidentiality and privacy in exchange of information including the new global standard of automatic exchange of information. Section 2 will analyse the state of the art regarding the right to privacy and confidentiality in

75 FR 34499 - Self-Regulatory Organizations; International Securities Exchange, LLC; Notice of Filing and...

Science.gov (United States)

2010-06-17

... maker/taker pricing program. The text of the proposed rule change is available on the Exchange's Web... qualification standards for market makers to receive a rebate under the Exchange's maker/taker pricing program... trading month for series trading between $0.03 and $5.00 in premium. \\8\\ The concept of incenting market...

An efficient and low resistant circumferential overlap trisection helical baffle heat exchanger with folded baffles

International Nuclear Information System (INIS)

Dong, Cong; Li, Dongshuang; Zheng, Youqu; Li, Guoneng; Suo, Yange; Chen, Yaping

2016-01-01

Highlights: • The novel cothHXf with circumferential overlap and folded baffles is first proposed. • The key sections of cylindrical and dumbbell are constructed to analyze local flow field characteristics. • The restricted leakage, easier to install and low resistant characteristics are emphasized. • The enhanced heat transfer mechanism of Dean Vortex secondary flow is analyzed. • A variety of comprehensive efficiency assessments are used. - Abstract: An efficient and low resistant circumferential overlap trisection helical baffle shell-and-tube heat exchanger with folded baffles (cothHXf) is presented. It is a modified trisection helical baffle heat exchanger with folded helical baffles for setting rods-and-spanning sleeves. It not only inherits all the merits of circumferential overlap helical baffle scheme, but also adds many additional advantages, such as supporting the inclined baffles with the least rods, simplifying the manufacturing process of spanning tubes and effectively inhibiting the reverse leakage at triangular areas between adjacent baffles. The improved flow characteristic and heat transfer enhancement mechanism of this heat exchanger were numerically investigated in comparison with conventional segmental baffles shell-and-tube heat exchanger (segHX). The flow fields within triangular area of adjacent baffles and nearby regions were depicted. The impacts of the folded baffles on shell-side helical flow, secondary vortex flow, and leakage pattern were analyzed. The distribution configurations of fields of velocity, pressure, temperature and local heat flow rate were revealed. The results show that the heat transfer performance and comprehensive performance evaluation indexes of the cothHXf are much better than those of the segHX while the pressure drop of the cothHXf is much lower than that of the segHX. The numerical simulation results of vivid distributions of flow and thermal fields of the cothHXf can provide theoretical basis for an

A Hydrogen Exchange Method Using Tritium and Sephadex: Its Application to Ribonuclease*

Science.gov (United States)

Englander, S. Walter

2012-01-01

A new method for measuring the hydrogen exchange of macromolecules in solution is described. The method uses tritium to trace the movement of hydrogen, and utilizes Sephadex columns to effect, in about 2 minutes, a separation between tritiated macromolecule and tritiated solvent great enough to allow the measurement of bound tritium. High sensitivity and freedom from artifact is demonstrated and the possible value of the technique for investigation of other kinds of colloid-small molecule interaction is indicated. Competition experiments involving tritium, hydrogen, and deuterium indicate the absence of any equilibrium isotope effect in the ribonuclease-hydrogen isotope system, though a secondary kinetic isotope effect is apparent when ribonuclease is largely deuterated. Ribonuclease shows four clearly distinguishable kinetic classes of exchangeable hydrogens. Evidence is marshaled to suggest the independently measurable classes II, III, and IV (in order of decreasing rate of exchange) to represent “random-chain” peptides, peptides involved in α-helix, and otherwise shielded side-chain and peptide hydrogens, respectively. PMID:14075117

A review of medical terminology standards and structured reporting.

Science.gov (United States)

Awaysheh, Abdullah; Wilcke, Jeffrey; Elvinger, François; Rees, Loren; Fan, Weiguo; Zimmerman, Kurt

2018-01-01

Much effort has been invested in standardizing medical terminology for representation of medical knowledge, storage in electronic medical records, retrieval, reuse for evidence-based decision making, and for efficient messaging between users. We only focus on those efforts related to the representation of clinical medical knowledge required for capturing diagnoses and findings from a wide range of general to specialty clinical perspectives (e.g., internists to pathologists). Standardized medical terminology and the usage of structured reporting have been shown to improve the usage of medical information in secondary activities, such as research, public health, and case studies. The impact of standardization and structured reporting is not limited to secondary activities; standardization has been shown to have a direct impact on patient healthcare.

Tensor exchange amplitudes in K +- N charge exchange reactions

International Nuclear Information System (INIS)

Svec, M.

1979-01-01

Tensor (A 2 ) exchange amplitudes in K +- N charge exchange (CEX) are constructed from the K +- N CEX data supplemented by information on the vector (rho) exchange amplitudes from πN sca tering. We observed new features in the t-structure of A 2 exchange amplitudes which contradict the t-de pendence anticipated by most of the Regge models. The results also provide evidence for violation of weak exchange degeneracy

Suppression of exchange bias effect in maghemite nanoparticles functionalized with H{sub 2}Y

Energy Technology Data Exchange (ETDEWEB)

Guivar, Juan A. Ramos, E-mail: juan.ramos5@unmsm.edu.pe [Faculty of Physical Sciences, National University of San Marcos, P. O. Box 14-0149, Lima, 14 Peru (Peru); Morales, M.A. [Departamento de Física Teórica e Experimental, UFRN, Natal, RN, 59078-970 Brazil (Brazil); Litterst, F. Jochen [Institut für Physik der Kondensierten Materie, Technische Universität Braunschweig, Braunschweig, 38110 Germany (Germany)

2016-12-15

The structural, vibrational, morphological and magnetic properties of maghemite (γ-Fe{sub 2}O{sub 3}) nanoparticles functionalized with polar molecules EDTA(or H{sub 4}Y) and H{sub 2}Y are reported. The samples were functionalized before and after total synthesis of γ-Fe{sub 2}O{sub 3} nanoparticles. The molecules are anchored on the monodentate mode on the nanoparticles surface. Transmission electron microscopy (TEM) revealed the formation of maghemite nanoparticles with small diameter of 4 nm for the sample functionalized upon synthesis and 7.6 and 6.9 nm for the samples functionalized with EDTA and H{sub 2}Y after the formation of nanoparticles. Exchange bias phenomena were observed in some of the samples functionalized with EDTA at temperatures below 70 K. The presence of the bias effect was discussed in terms of the formation of a thin layer of a secondary phase like lepidocrocite, and the absence of this effect was explained in terms of the chemisorption of carboxylic groups from EDTA which suppressed the canting. Studies of Mössbauer spectroscopy as a function of temperature showed slow relaxation effects and allowed discussion of the secondary phase. In the M–T curves a maximum around 116 K was associated with this secondary phase also in agreement with the Mössbauer studies. The dynamic properties were studied by AC susceptibility, the out of phase signal revealed a spin glass like regime below 36.5 K. - Highlights: • Coprecipitation in alkaline medium was used for the synthesis of EDTA functionalized small maghemite nanoparticles. • Exchange bias effect was observed due to a thin layer of lepidocrocite like second phase. • The sample coprecipitated in a weak base did not show exchange bias effect. • The bias effect is discussed in terms of suppression of canting due to chemisorption of carboxylic groups from EDTA.

Direct observations of Biogenic Volatile Organic Compound (BVOC) Air-Sea Exchange in the remote North Atlantic from the High-Wind Gas-Exchange Study (HiWinGS)

Science.gov (United States)

Kim, M.; Yang, M. X.; Blomquist, B.; Huebert, B. J.; Bertram, T. H.

2014-12-01

Biogenic Volatile Organic Compounds (BVOCs) are reactive trace gases that impact both chemistry and climate by regulating oxidant loadings, determining secondary organic aerosol production rates as well as altering particle hygroscopicity. While continental BVOC exchange rates are well studied, global marine flux estimates are poorly constrained. In Fall 2013, a chemical-ionization time-of-flight mass spectrometer (CI-ToF-MS) utilizing benzene cations was deployed as part of the High Wind Gas Exchange Study (HiWinGs) to quantify monoterpenes, isoprene and dimethylsulfide fluxes in the remote North Atlantic. Dimethylsulfide measurements are in strong agreement with those determined by the University of Hawaii's atmospheric pressure ionization mass-spectrometer. In the remote marine boundary layer, positive monoterpene fluxes (i.e. emissions) were observed while isoprene levels rarely exceeded the detection limit.

Potential for ultrasonic inspection of heat exchanger tubes

International Nuclear Information System (INIS)

Ward, M.J.

1980-01-01

Preliminary results of a program to develop an ultrasonic inspection method for heat-exchanger tubes, to be used as alternative or complementary to eddy-curent testing were sufficiently promising to warrant further study. Problems were encountered in adapting a standard commercial transducer and a custom-made transducer to provide full 360 degree coverage of an area for in-service inspection, but it might be possible to overcome these problems. The results showed it might prove impossible to design a transducer to handle the tight U-bends in some heat exchangers. The most promising area of application for ultrasonic inspection was found to be around the tubesheet. (DN)

Calibration of working standard ionization chambers and dose standardization

International Nuclear Information System (INIS)

Abd Elmahoud, A. A. B.

2011-01-01

Measurements were performed for the calibration of two working standard ionization chambers in the secondary standard dosimetry laboratory of Sudan. 600 cc cylindrical former type and 1800 cc cylindrical radical radiation protection level ionization chambers were calibrated against 1000 cc spherical reference standard ionization chamber. The chamber were calibrated at X-ray narrow spectrum series with beam energies ranged from (33-116 KeV) in addition to 1''3''7''Cs beam with 662 KeV energy. The chambers 0.6 cc and 0.3 cc therapy level ionization were used for dose standardization and beam output calibrations of cobalt-60 radiotherapy machine located at the National Cancer Institute, University of Gazira. Concerning beam output measurements for 6''0''Co radiotherapy machine, dosimetric measurements were performed in accordance with the relevant per IAEA dosimetry protocols TRS-277 and TRS-398. The kinetic energy released per unit mass in air (air kerma) were obtained by multiplying the corrected electrometer reading (nC/min) by the calibration factors (Gy/n C) of the chambers from given in the calibration certificate. The uncertainty of measurements of air kerma were calculated for the all ionization chambers (combined uncertainty) the calibration factors of these ionization chambers then were calculated by comparing the reading of air kerma of secondary standard ionization chambers to than from radical and farmer chambers. The result of calibration working standard ionization chambers showed different calibration factors ranged from 0.99 to 1.52 for different radiation energies and these differences were due to chambers response and specification. The absorbed dose to to water calculated for therapy ionization chamber using two code of practice TRS-277 and TRS-398 as beam output for 6''0''Co radiotherapy machine and it can be used as a reference for future beam output calibration in radiotherapy dosimetry. The measurement of absorbed dose to water showed that the

Severe iron intoxication treated with exchange transfusion

DEFF Research Database (Denmark)

Carlsson, Marcella; Cortes, Dina; Jepsen, Søren

2008-01-01

An 18-month-old previous healthy girl who had ingested 442 mg elemental iron/kg was admitted to a paediatric intensive care unit. The child was treated with gastric lavage, whole bowel irrigation and intravenous deferoxamine. After 2 h of standard therapy serum iron had risen threefold to 1362 mi...... microg/dl (244 micromol/l). The child was treated with exchange transfusion (ET; 52 ml/kg) and serum iron fell to 134 microg/dl (24 micromol/l). The patient made an uncomplicated recovery. ET should be considered in severe iron poisoning when standard therapy is inadequate....

Aspects of quantitative secondary ion mass spectrometry

International Nuclear Information System (INIS)

Grauer, R.

1982-05-01

Parameters which have an influence on the formation of secondary ions by ion bombardment of a solid matrix are discussed. Quantitative SIMS-analysis with the help of calibration standards necessitates a stringent control of these parameters. This is particularly valid for the oxygen partial pressure which for metal analysis has to be maintained constant also under ultra high vacuum. The performance of the theoretical LTE-model (Local Thermal Equilibrium) using internal standards will be compared with the analysis with the help of external standards. The LTE-model does not satisfy the requirements for quantitative analysis. (Auth.)

Issues and remedies for secondary system of PWR/VVER

International Nuclear Information System (INIS)

Nordmann, Francis; Odar, Suat; Rochester, Dewey

2012-09-01

Secondary side degradation of steam generators (SG) and Flow Accelerated Corrosion (FAC) in the secondary system have been for a long time important issues in PWR and VVER types of Nuclear Power Plants. With the evolution of the design, the most important issues are progressively moving from secondary side corrosion of Alloy 600 SG tubing, which is being replaced, to a larger variety of risks associated with potential inadequate chemistries. As far as FAC of carbon steel is concerned, the evolution of treatment selection for minimizing corrosion products transport toward the SG, as well as progressive replacement of components in the feedwater train, decreases the risk of dramatic failures which have occurred in the past. After having briefly explained the reason for the past problems encountered in the secondary system of PWR and VVER, this paper evaluates the risk associated with various impurities or contaminants that may be present in the secondary system and how to mitigate them in the most appropriate, efficient, economical and environmental friendly way. The covered species are sodium, calcium, magnesium, chloride, sulfate and sulfur compounds, fluorides, organic compounds, silica, oxygen, lead, ion exchange resins. This paper also proposes the best remedies for mitigating the new issues that may be encountered in operating plants or units under construction. These are mainly: - Selecting a steam water treatment able to minimize the quantity of corrosion products transported toward the SG; - Mitigating the risk of Flow Induced Vibration by a proper control of deposits in sensitive areas; - Minimizing the risk of concentration of impurities in local areas where they may induce corrosion; - Avoiding the presence of abnormal quantities of some species in SG, such as the detrimental presence of lead and ion exchange resin debris or the controversial presence of organic compounds; - Optimizing costs of maintenance activities (SG mechanical, chemical cleaning

Exchange functional by a range-separated exchange hole

International Nuclear Information System (INIS)

Toyoda, Masayuki; Ozaki, Taisuke

2011-01-01

An approximation to the exchange-hole density is proposed for the evaluation of the exact exchange energy in electronic structure calculations within the density-functional theory and the Kohn-Sham scheme. Based on the localized nature of density matrix, the exchange hole is divided into the short-range (SR) and long-range (LR) parts by using an adequate filter function, where the LR part is deduced by matching of moments with the exactly calculated SR counterpart, ensuring the correct asymptotic -1/r behavior of the exchange potential. With this division, the time-consuming integration is truncated at a certain interaction range, largely reducing the computation cost. The total energies, exchange energies, exchange potentials, and eigenvalues of the highest-occupied orbitals are calculated for the noble-gas atoms. The close agreement of the results with the exact values suggests the validity of the approximation.

The importance of secondary radiation at radiation protection clothing; Die Bedeutung der Sekundaerstrahlung bei Strahlenschutzkleidung

Energy Technology Data Exchange (ETDEWEB)

Eder, Heinrich

2017-07-01

For a long time, the protective material lead was seen as ''gold standard'' for the shielding of photon radiation (X-ray and γ-rays). At long sight, however, lead should be eliminated from medical products. When irradiated, substitutes of lead can produce much more secondary radiation. Moreover, the radiobiological impact of the low energetic secondary radiation has to be rated higher than that of primary radiation. With the introduction of the new measuring standard IEC 6133-1 secondary radiation now is considered when evaluating attenuation properties of protective clothing.

78 FR 12655 - Federal-State Unemployment Insurance (UI) Program; Data Exchange Standardization as Required by...

Science.gov (United States)

2013-02-25

... elimination of the need to create and mail hard copy documents; Increasing accuracy and reducing errors (in... formatting requirements for the data exchanges of various UI applications that may impose a burden under the...

Fabrication of 12% 240Pu calorimetry standards

International Nuclear Information System (INIS)

Long, S.M.; Hildner, S.; Gutierrez, D.; Mills, C.; Garcia, W.; Gurule, C.

1995-01-01

Throughout the DOE complex, laboratories are performing calorimetric assays on items containing high burnup plutonium. These materials contain higher isotopic range and higher wattages than materials previously encountered in vault holdings. Currently, measurement control standards have been limited to utilizing 6% 240 Pu standards. The lower isotopic and wattage value standards do not complement the measurement of the higher burnup material. Participants of the Calorimetry Exchange (CALEX) Program have identified the need for new calorimetric assay standards with a higher wattage and isotopic range. This paper describes the fabrication and verification measurements of the new CALEX standard containing 12% 240 Pu oxide with a wattage of about 6 to 8 watts

76 FR 54293 - Review of National Ambient Air Quality Standards for Carbon Monoxide

Science.gov (United States)

2011-08-31

...), hypertension (high blood pressure), and peripheral vascular diseases. Heart disease, in turn, comprises several... further concludes that no secondary standard should be set for CO at this time. EPA is also making changes.... Consideration of a Secondary Standard A. Introduction B. Rationale for Proposed Decision C. Comments on...

Report of the third meeting of the SSDL Scientific Committee (SSC). Vienna, 19-23 September 1988[Secondary Standard Dosimetry Laboratories

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-12-01

The SSDL Scientific Committee (SSC) was appointed in 1985 by the Director General of the IAEA, in consultation with and the concurrence of the Director General of the WHO. As indicated in its Terms of Reference, the main objective of the SSC is to advise the Directors General of the IAEA and WHO regarding the programme of work of the IAEA/WHO Network of Secondary Standard Dosimetry Laboratories (SSDLs). The first meeting of the SSC was held in May 1986 and the recommendations were reported in IAEA SSDL Newsletter No. 25, October 1986. The second meeting of the SSC was held in June 1987 and the recommendations were reported in the SSDL Newsletter No. 26, October 1987. Discussions and recommendations of this meeting are covered in this report.

Air-sea Exchange of Polycyclic Aromatic Hydrocarbons (PAHs), Polychlorinated Biphenyls (PCBs), Organochlorine Pesticides (OCPs) and Polybrominated Diphenyl Ethers (PBDEs) in the Mediterranean Sea

Science.gov (United States)

Lammel, G. P.; Heil, A.; Kukucka, P.; Meixner, F. X.; Mulder, M. D.; Prybilova, P.; Prokes, R.; Rusina, T. S.; Song, G. Z.; Vrana, B.

2015-12-01

The marine atmospheric environment is a receptor for persistent organic pollutants (POPs) which are advected from sources on land, primary, such as biomass burning by-products (PAHs, dioxins), and secondary, such as volatilization from contaminated soils (PCBs, pesticides). Primary sources do not exist in the marine environment, except for PAHs (ship engines) but following previous atmospheric deposition, the sea surface may turn to a secondary source by reversal of diffusive air-sea mass exchange. No monitoring is in place. We studied the vertical fluxes of a wide range of primary and secondary emitted POPs based on measurements in air and surface seawater at a remote coastal site in the eastern Mediterranean (2012). To this end, silicon rubbers were used as passive water samplers, vertical concentration gradients were determined in air and fluxes were quantified based on Eddy covariance. Diffusive air-sea exchange fluxes of hexachlorocyclohexanes (HCHs) and semivolatile PAHs were found close to phase equilibrium, except one PAH, retene, a wood burning tracer, was found seasonally net-volatilisational. Some PCBs, p,p'-DDE, penta- and hexachlorobenzene (PeCB, HCB) were mostly net-depositional, while PBDEs were net-volatilizational. Fluxes determined at a a remote coastal site ranged -33 - +2.4 µg m-2 d-1 for PAHs and -4.0 - +0.3 µg m-2 d-1for halogenated compounds ( 0 means net-volatilization). It is concluded that nowadays in open seas more pollutants are undergoing reversal of the direction of air-sea exchange. Recgional fire activity records in combination with box model simulations suggest that deposition of retene during summer is followed by a reversal of air-sea exchange. The seawater surface as secondary source of pollution should be assessed based on flux measurements across seasons and over longer time periods.

The SGML Standardization Framework and the Introduction of XML

Science.gov (United States)

Grütter, Rolf

2000-01-01

Extensible Markup Language (XML) is on its way to becoming a global standard for the representation, exchange, and presentation of information on the World Wide Web (WWW). More than that, XML is creating a standardization framework, in terms of an open network of meta-standards and mediators that allows for the definition of further conventions and agreements in specific business domains. Such an approach is particularly needed in the healthcare domain; XML promises to especially suit the particularities of patient records and their lifelong storage, retrieval, and exchange. At a time when change rather than steadiness is becoming the faithful feature of our society, standardization frameworks which support a diversified growth of specifications that are appropriate to the actual needs of the users are becoming more and more important; and efforts should be made to encourage this new attempt at standardization to grow in a fruitful direction. Thus, the introduction of XML reflects a standardization process which is neither exclusively based on an acknowledged standardization authority, nor a pure market standard. Instead, a consortium of companies, academic institutions, and public bodies has agreed on a common recommendation based on an existing standardization framework. The consortium's process of agreeing to a standardization framework will doubtlessly be successful in the case of XML, and it is suggested that it should be considered as a generic model for standardization processes in the future. PMID:11720931

Probing the Gaseous Structure of a β-Hairpin Peptide with H/D Exchange and Electron Capture Dissociation.

Science.gov (United States)

Straus, Rita N; Jockusch, Rebecca A

2017-02-01

An improved understanding of the extent to which native protein structure is retained upon transfer to the gas phase promises to enhance biological mass spectrometry, potentially streamlining workflows and providing fundamental insights into hydration effects. Here, we investigate the gaseous conformation of a model β-hairpin peptide using gas-phase hydrogen-deuterium (H/D) exchange with subsequent electron capture dissociation (ECD). Global gas-phase H/D exchange levels, and residue-specific exchange levels derived from ECD data, are compared among the wild type 16-residue peptide GB1p and several variants. High protection from H/D exchange observed for GB1p, but not for a truncated version, is consistent with the retention of secondary structure of GB1p in the gas phase or its refolding into some other compact structure. Four alanine mutants that destabilize the hairpin in solution show levels of protection similar to that of GB1p, suggesting collapse or (re)folding of these peptides upon transfer to the gas phase. These results offer a starting point from which to understand how a key secondary structural element, the β-hairpin, is affected by transfer to the gas phase. This work also demonstrates the utility of a much-needed addition to the tool set that is currently available for the investigation of the gaseous conformation of biomolecules, which can be employed in the future to better characterize gaseous proteins and protein complexes. Graphical Abstract ᅟ.

A standard-enabled workflow for synthetic biology.

Science.gov (United States)

Myers, Chris J; Beal, Jacob; Gorochowski, Thomas E; Kuwahara, Hiroyuki; Madsen, Curtis; McLaughlin, James Alastair; Mısırlı, Göksel; Nguyen, Tramy; Oberortner, Ernst; Samineni, Meher; Wipat, Anil; Zhang, Michael; Zundel, Zach

2017-06-15

A synthetic biology workflow is composed of data repositories that provide information about genetic parts, sequence-level design tools to compose these parts into circuits, visualization tools to depict these designs, genetic design tools to select parts to create systems, and modeling and simulation tools to evaluate alternative design choices. Data standards enable the ready exchange of information within such a workflow, allowing repositories and tools to be connected from a diversity of sources. The present paper describes one such workflow that utilizes, among others, the Synthetic Biology Open Language (SBOL) to describe genetic designs, the Systems Biology Markup Language to model these designs, and SBOL Visual to visualize these designs. We describe how a standard-enabled workflow can be used to produce types of design information, including multiple repositories and software tools exchanging information using a variety of data standards. Recently, the ACS Synthetic Biology journal has recommended the use of SBOL in their publications. © 2017 The Author(s); published by Portland Press Limited on behalf of the Biochemical Society.

The STEP standard as an approach for design and prototyping

OpenAIRE

Plantec , Alain; Ribaud , Vincent

1998-01-01

International audience; STEP is an ISO standard (ISO-10303) for the computer-interpretable representation and exchange of product data. Parts of STEP standardize conceptual structures and usage of information in generic or specific domains. The standardization process of these constructs is an evolutionary approach , which uses generated prototypes at different phases of the process. This paper presents a method for the building of prototype generators, inspired by this standardization proces...

Automated exchange transfusion and exchange rate.

Science.gov (United States)

Funato, M; Shimada, S; Tamai, H; Taki, H; Yoshioka, Y

1989-10-01

An automated blood exchange transfusion (BET) with a two-site technique has been devised by Goldmann et al and by us, using an infusion pump. With this method, we successfully performed exchange transfusions 189 times in the past four years on 110 infants with birth weights ranging from 530 g to 4,000 g. The exchange rate by the automated method was compared with the rate by Diamond's method. Serum bilirubin (SB) levels before and after BET and the maximal SB rebound within 24 hours after BET were: 21.6 +/- 2.4, 11.5 +/- 2.2, and 15.0 +/- 1.5 mg/dl in the automated method, and 22.0 +/- 2.9, 11.2 +/- 2.5, and 17.7 +/- 3.2 mg/dl in Diamond's method, respectively. The result showed that the maximal rebound of the SB level within 24 hours after BET was significantly lower in the automated method than in Diamond's method (p less than 0.01), though SB levels before and after BET were not significantly different between the two methods. The exchange rate was also measured by means of staining the fetal red cells (F cells) both in the automated method and in Diamond's method, and comparing them. The exchange rate of F cells in Diamond's method went down along the theoretical exchange curve proposed by Diamond, while the rate in the automated method was significantly better than in Diamond's, especially in the early stage of BET (p less than 0.01). We believe that the use of this automated method may give better results than Diamond's method in the rate of exchange, because this method is performed with a two-site technique using a peripheral artery and vein.

Structure and properties of silver sulfate complexes derived from dipyridyl methylthio ligands with secondary donor site

Energy Technology Data Exchange (ETDEWEB)

Chen, Wen-Hua; Yan, Hao-Jie; Chen, Hui; Liu, Rui-Heng; Li, Ai-Min; Wang, Guo [Beijing Key Laboratory for Optical Materials and Photonic Devices, Department of Chemistry, Capital Normal University, Beijing 100048 (China); Wan, Chong-Qing, E-mail: wancq@cnu.edu.cn [Beijing Key Laboratory for Optical Materials and Photonic Devices, Department of Chemistry, Capital Normal University, Beijing 100048 (China); State Key Laboratory of Structural Chemistry in China, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China)

2017-06-15

Dipyridyl sulphide ligands 4-(pyridin-4-ylmethylthio)pyridine (abbreviated as L1) and 3-(pyridin-4-ylmethylthio)pyridine (abbreviated as L2) have been designed and used as μ-{sub N},{sub N}-bridging linkages to construct coordination polymers with free –S–CH{sub 2}– groups as secondary donor sites. By use solvent control method, coordination polymers ([Ag{sub 3}SO{sub 4}(L1){sub 3}](Cl)·4.5H{sub 2}O){sub ∞}(1), ([Ag{sub 2}SO{sub 4}(L1){sub 2}]·6H{sub 2}O·2CH{sub 3}OH){sub ∞}(2), ([Ag{sub 2}SO{sub 4}(L2){sub 2}]·H{sub 2}O){sub ∞}(3) and ([Ag{sub 4}(SO{sub 4}){sub 2}(L2){sub 4}]·5H{sub 2}O){sub ∞}(4) with different architectures were obtained. Complexes 1, 3 and 4 feature 1D channel with different sizes and structures. Complex 1 exhibits guest exchange by THF and 1,4-dioxane, and Hg{sup 2+} sorption ability from solution due to its relative larger channel and available bonding sites of –S– exposed to the channel region. All complexes have been characterized through single-crystal and powder X-ray diffraction (PXRD), FT-IR spectra, X-ray photoelectron spectroscopy (XPS), elemental and thermogravimetric analyses. The guest exchange and Hg{sup 2+} sorption were monitored and identified, and the structure-property relationship of coordination polymers 1–4 are discussed. - Graphical abstract: Coordination polymers of silver(I) sulfate with secondary donor sites are shown guest exchange property and Hg{sup 2+} absorb ability from solution. This work provides a new method to construct functional materials with potential application. - Highlights: • New example of constructing functional coordination polymer with secondary donor methylthio group. • Guest exchange and interesting Hg(II) absorb ability from solution are investigated. • New method to construct functional materials with potential application.

Numerical Simulations of Particle Deposition in Metal Foam Heat Exchangers

Science.gov (United States)

Sauret, Emilie; Saha, Suvash C.; Gu, Yuantong

2013-01-01

Australia is a high-potential country for geothermal power with reserves currently estimated in the tens of millions of petajoules, enough to power the nation for at least 1000 years at current usage. However, these resources are mainly located in isolated arid regions where water is scarce. Therefore, wet cooling systems for geothermal plants in Australia are the least attractive solution and thus air-cooled heat exchangers are preferred. In order to increase the efficiency of such heat exchangers, metal foams have been used. One issue raised by this solution is the fouling caused by dust deposition. In this case, the heat transfer characteristics of the metal foam heat exchanger can dramatically deteriorate. Exploring the particle deposition property in the metal foam exchanger becomes crucial. This paper is a numerical investigation aimed to address this issue. Two-dimensional (2D) numerical simulations of a standard one-row tube bundle wrapped with metal foam in cross-flow are performed and highlight preferential particle deposition areas.

South Africa and United States stock prices and the Rand/Dollar exchange rate

Directory of Open Access Journals (Sweden)

Matthew Ocran

2010-09-01

Full Text Available This paper seeks to examine the dynamic causal relations between the two major financial assets, stock prices of the US and South Africa and the rand/US$ exchange rate. The study uses a mixed bag of time series approaches such as cointegration, Granger causality, impulse response functions and forecasting error variance decompositions.  The paper identifies a bi-directional causality from the Standard & Poor’s 500 stock price index to the rand/US$ exchange rate in the Granger sense. It was also found that the Standard & Poor’s stock price index accounts for a significant portion of the variations in the Johannesburg Stock Exchange’s All Share index. Thus, while causality in the Granger sense could not be established for the relationship between the price indices of the two stock exchanges it can argued that there is some relationship between them. The results of the study have implications for both business and Government.

Antibacterial activity of secondary metabolites isolated from ...

African Journals Online (AJOL)

Aghomotsegin

2015-10-28

Oct 28, 2015 ... Alternaria spp. are cosmopolitan mould fungi and can be found in soils ... the secondary metabolites products from A. alternata and ..... Zone of inhibition (mm) of test bacterial strains to fungal products and standard antibiotics. Fungal ... marine actinomycetes from pulicat, Muttukadu, and Ennore estuaries.

Sports eyewear protective standards.

Science.gov (United States)

Dain, Stephen J

2016-01-01

Eye injuries sustained during sport comprise up to 20 per cent of all injuries to the eye serious enough for medical attention to be sought. The prevalence of eye injuries in sport is not easily assessed due to lack of authoritative participation rates, so most studies report total numbers in a time period. The evidence on the proportion of all ocular injuries that are from sport is reviewed. The relative frequencies in different sports are compared in a qualitative manner and the sports with greater numbers of ocular injuries are detailed. In common with occupational injuries to the eye, most sports eye injuries are considered preventable. The hierarchy of action for occupational risk is detailed and adapted to use in a sports scenario. All the available international, regional and national standards on sports eye protection are detailed and their provisions compared. The major function of the standards is to provide adequate protection against the hazard of the sport concerned. These are detailed and compared as a function of energy transfer. Eye protection must not introduce additional or secondary hazards (for instance, fracturing into sharp fragments on impact) and not introduce features that would deter the wearing of eye protection (for instance, restricting field of view to impede playing the sport). The provisions of the standards intended to limit secondary hazards are detailed and compared. The need for future work in standards writing and the activities of the International Standardization Organization in sports eye protection are detailed. © 2016 Optometry Australia.

Graphite Foam Heat Exchangers for Thermal Management

Energy Technology Data Exchange (ETDEWEB)

Klett, J.W.

2004-06-07

Improved thermal management is needed to increase the power density of electronic and more effectively cool electronic enclosures that are envisioned in future aircraft, spacecraft and surface ships. Typically, heat exchanger cores must increase in size to more effectively dissipate increased heat loads, this would be impossible in many cases, thus improved heat exchanger cores will be required. In this Phase I investigation, MRi aimed to demonstrate improved thermal management using graphite foam (Gr-foam) core heat exchangers. The proposed design was to combine Gr-foams from POCO with MRi's innovative low temperature, active metal joining process (S-Bond{trademark}) to bond Gr-foam to aluminum, copper and aluminum/SiC composite faceplates. The results were very favorable, so a Phase II SBIR with the MDA was initiated. This had primarily 5 tasks: (1) bonding, (2) thermal modeling, (3) cooling chip scale packages, (4) evaporative cooling techniques and (5) IGBT cold plate development. The bonding tests showed that the ''reflow'' technique with S-Bond{reg_sign}-220 resulted in the best and most consistent bond. Then, thermal modeling was used to design different chip scale packages and IGBT cold plates. These designs were used to fabricate many finned graphite foam heat sinks specifically for two standard type IC packages, the 423 and 478 pin chips. These results demonstrated several advantages with the foam. First, the heat sinks with the foam were lighter than the copper/aluminum sinks used as standards. The sinks for the 423 design made from foam were not as good as the standard sinks. However, the sinks made from foam for the 478 pin chips were better than the standard heat sinks used today. However, this improvement was marginal (in the 10-20% better regime). However, another important note was that the epoxy bonding technique resulted in heat sinks with similar results as that with the S-bond{reg_sign}, slightly worse than the S

Mild Conditions for Deuteration of Primary and Secondary Arylamines for the Synthesis of Deuterated Optoelectronic Organic Molecules

Directory of Open Access Journals (Sweden)

Anwen M. Krause-Heuer

2014-11-01

Full Text Available Deuterated arylamines demonstrate great potential for use in optoelectronic devices, but their widespread utility requires a method for large-scale synthesis. The incorporation of these deuterated materials into optoelectronic devices also provides the opportunity for studies of the functioning device using neutron reflectometry based on the difference in the scattering length density between protonated and deuterated compounds. Here we report mild deuteration conditions utilising standard laboratory glassware for the deuteration of: diphenylamine, N-phenylnaphthylamine, N-phenyl-o-phenylenediamine and 1-naphthylamine (via H/D exchange in D2O at 80 °C, catalysed by Pt/C and Pd/C. These conditions were not successful in the deuteration of triphenylamine or N,N-dimethylaniline, suggesting that these mild conditions are not suitable for the deuteration of tertiary arylamines, but are likely to be applicable for the deuteration of other primary and secondary arylamines. The deuterated arylamines can then be used for synthesis of larger organic molecules or polymers with optoelectronic applications.

Heat exchanger

International Nuclear Information System (INIS)

Dostatni, A.W.; Dostatni, Michel.

1976-01-01

In the main patent, a description was given of a heat exchanger with an exchange surface in preformed sheet metal designed for the high pressure and temperature service particularly encountered in nuclear pressurized water reactors and which is characterised by the fact that it is composed of at least one exchanger bundle sealed in a containment, the said bundle or bundles being composed of numerous juxtaposed individual compartments whose exchange faces are built of preformed sheet metal. The present addendun certificate concerns shapes of bundles and their positioning methods in the exchanger containment enabling its compactness to be increased [fr

Standardized Cloning and Curing of Plasmids

DEFF Research Database (Denmark)

Lauritsen, Ida; Kim, Se Hyeuk; Porse, Andreas

2018-01-01

and exchange of genetic parts in the Standard European Vectors Architecture (SEVA) vector system. Additionally, to facilitate rapid testing and iterative bioengineering using different vector designs, we provide a one-step protocol for a universal CRISPR-Cas9-based plasmid curing system (pFREE) and demonstrate...

High Efficiency Heat Exchanger for High Temperature and High Pressure Applications

Energy Technology Data Exchange (ETDEWEB)

Sienicki, James J. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Lv, Qiuping [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Moisseytsev, Anton [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division

2017-09-29

channels so that each fluid is fully surrounded by the opposing fluid. As compared to similar existing compact heat exchangers, the new design converts most secondary surface area to primary surface area, eliminating fin inefficiencies. CompRex requests that all technical information about the heat exchanger designs be protected as proprietary information. To honor that request, only non-proprietay summaries are included in this report.

Computer simulation of natural circulation in FFTF secondary loops

International Nuclear Information System (INIS)

Beaver, T.R.; Turner, D.M.; Additon, S.L.

1979-07-01

A thermal/hydraulic model of the FFTF secondary heat transport loop has been calibrated against transient natural circulation test data collected March to May 1979. The tests verified that the transition to natural convective flow could be effected from near isothermal conditions without excessive cooling at the air dump heat exchangers. Key empirical parameters of pressure drop and heat loss were found to be at 88% and 81% of pretest estimates, respectively. Pretest piping thermal transport and flow calculational models required no further revision to produce good agreement with test data

A team-level investigation of the relationship between leader-member-exchange (LMX) differentiation and commitment and performance

NARCIS (Netherlands)

Le Blanc, P.M.; González-Romá, V.

2012-01-01

Although the differential treatment of team members by their leader is at the heart of Leader–Member Exchange (LMX) theory, empirical studies exploring the role of within-team LMX differentiation in relation to team outcomes are still relatively scarce. This study among 269 Dutch secondary school

Enabling global exchange of groundwater data: GroundWaterML2 (GWML2)

Science.gov (United States)

Brodaric, Boyan; Boisvert, Eric; Chery, Laurence; Dahlhaus, Peter; Grellet, Sylvain; Kmoch, Alexander; Létourneau, François; Lucido, Jessica; Simons, Bruce; Wagner, Bernhard

2018-03-01

GWML2 is an international standard for the online exchange of groundwater data that addresses the problem of data heterogeneity. This problem makes groundwater data hard to find and use because the data are diversely structured and fragmented into numerous data silos. Overcoming data heterogeneity requires a common data format; however, until the development of GWML2, an appropriate international standard has been lacking. GWML2 represents key hydrogeological entities such as aquifers and water wells, as well as related measurements and groundwater flows. It is developed and tested by an international consortium of groundwater data providers from North America, Europe, and Australasia, and facilitates many forms of data exchange, information representation, and the development of online web portals and tools.

Enabling global exchange of groundwater data: GroundWaterML2 (GWML2)

Science.gov (United States)

Brodaric, Boyan; Boisvert, Eric; Chery, Laurence; Dahlhaus, Peter; Grellet, Sylvain; Kmoch, Alexander; Létourneau, François; Lucido, Jessica; Simons, Bruce; Wagner, Bernhard

2018-05-01

GWML2 is an international standard for the online exchange of groundwater data that addresses the problem of data heterogeneity. This problem makes groundwater data hard to find and use because the data are diversely structured and fragmented into numerous data silos. Overcoming data heterogeneity requires a common data format; however, until the development of GWML2, an appropriate international standard has been lacking. GWML2 represents key hydrogeological entities such as aquifers and water wells, as well as related measurements and groundwater flows. It is developed and tested by an international consortium of groundwater data providers from North America, Europe, and Australasia, and facilitates many forms of data exchange, information representation, and the development of online web portals and tools.

Kinetics of zinc uptake and exchange by primary cultures of rat hepatocytes

International Nuclear Information System (INIS)

Pattison, S.E.; Cousins, R.J.

1986-01-01

The kinetics of 65 Zn 2+ uptake and exchange by hepatocytes in primary culture have been examined in detail to provide a basis for analyzing hormonal regulation of hepatic zinc metabolism. 65 Zn 2+ uptake was found to be a biphasic process. The slow phase represents an exchange between Zn 2+ in the medium and preexisting, intracellular zinc pools. This exchange rate was saturable with a medium zinc concentration of 9.5 microM eliciting one-half the maximum exchange rate and a maximum exchange rate of 9.9 pmol Zn 2+ . min-1 . mg protein-1 in the presence of bovine serum albumin. In the absence of albumin, a secondary, nonsaturable uptake rate was observed. The slow phase was relatively selective, and of the divalent transition metal ions tested, only Cd 2+ and Mn 2+ caused inhibition. The rate of exchange suggests total hepatocyte zinc has a turnover rate of approximately 30 h. The fast phase of 65 Zn 2+ reflects net Zn 2+ accumulation into a labile pool. The initial rates for this process were too fast to be measured accurately, but steady-state measurements allowed determination of the labile pool size. The pool dimensions saturated in the presence [Kapp = 28.6 microM; pool capacity = 0.44 nmol Zn 2+ /mg protein] and absence [Kapp = 11.8 microM; pool capacity = 0.34 nmol Zn 2+ /mg protein] of bovine serum albumin. Kinetics and equilibria of Zn 2+ uptake into the labile pool suggest that the latter acts as a source of Zn 2+ for the slow-exchange phase. Dexamethasone stimulated slow Zn 2+ exchange and also increased the labile pool size. The data suggest physiological factors alter hepatic zinc metabolism by influencing both intracellular Zn 2+ pools

Process and device for detecting and localizing leaks in a tube bundle heat exchanger when it is stopped

International Nuclear Information System (INIS)

Germain, J.L.; Jeanneteau, E.; Loisy, F.

1986-01-01

The device can be used to detect the tubes presenting leaks in a tube bundle exchanger of a light water reactor. This device comprises a feeding point to fill the secondary part of the exchanger, in which the tubes are immersed, with a pressure mixture of vector gas (air) and helium. It has also a feeding point to establish in the tube a sweeping air flow. An analysis apparatus, such as a spectrograph, measures the helium content of air at the outlet of each tube [fr

Radiation effects on ion-exchange resins. Part II. Gamma irradiation of Dowex 1

International Nuclear Information System (INIS)

Kazanjian, A.R.; Horrell, D.R.

1975-01-01

The effects were determined of gamma radiation on the anion exchange resin, Dowex 1. Part I on Dowex 50W was reported May 10, 1974. The exchange capacity (both strong and weak base), moisture content, radiolysis products, and physical deterioration of the resin were analyzed after irradiation with doses up to 6.9 x 10 8 rads. The resin capacity decreased approximately 50 percent after a radiation dose of 4 x 10 8 rads. Resin irradiated, when air dried in the nitrate form, showed more stability than resin irradiated in 7N nitric acid (HNO 3 ), which in turn showed more stability than resin irradiated when air dried in the chloride form. Radiation decreased the strong base capacity to a greater extent than the total capacity. The result indicates that some of the quarternary ammonium groups were transformed to secondary and tertiary amine groups that have weak base ion-exchange capability. (U.S.)

The NPL survey on tritium and radon standards

International Nuclear Information System (INIS)

Makepeace, J.; Curry, M.

1989-02-01

The survey was carried out to establish the ranges of activity and levels of uncertainty which would satisfy U.K. customers' needs for Tritium and Radon standards in gas and water. A secondary object was to obtain comments on needs for other standards. (U.K.)

Oscillatory Energy Exchange Between Waves Coupled by a Dynamic Artificial Crystal

OpenAIRE

Karenowska, Alexy D.; Tiberkevich, Vasil S.; Chumak, Andrii V.; Serga, Alexander A.; Gregg, John F.; Slavin, Andrei N.; Hillebrands, Burkard

2011-01-01

We describe a general mechanism of controllable energy exchange between waves propagating in a dynamic artificial crystal. We show that if a spatial periodicity is temporarily imposed on the transmission properties of a wave-carrying medium whilst a wave is inside, this wave is coupled to a secondary counter-propagating wave and energy oscillates between the two. The oscillation frequency is determined by the width of the spectral band gap created by the periodicity and the frequency differen...

The Effect of Exchange Rate Volatility on Iran’s Raisin Export

Directory of Open Access Journals (Sweden)

2014-10-01

Full Text Available Exchange rate volatility is one of the effective and ambiguous factors in agricultural product export. Considering the importance of agricultural trade to avoid single-product economy, the main aim of this study was to investigate the impact of exchange rate volatility on the Raisin export of Iran during the years1959-2011. For this purpose, exchange rate volatility index was estimated using Moving Average Standard Deviation (MASD. Then, the impact of exchange rate volatility on the value of Raisin export was examined using Johansen's and Juselius's cointegration method and Vector Error Correction Model (VECM.The results showed that in the long-term and short-term there is a significant relationship between Raisin exports and its main variables (weighted average of Gross income of importers, Wholesale Prices, real exchange rate, Value-added of agricultural sector; as according to the theory it has negative relationship with exchange rate volatility. The error correction coefficient sentence ECM (-1 significantly and its sign was negative as expected. The value of this coefficient is equal to the -0/20 and indicates that about 20 percent of Raisin exports imbalance from its long-term value, after of a period will be Elapse.

Membrane versus centrifuge-based therapeutic plasma exchange: a randomized prospective crossover study.

Science.gov (United States)

Hafer, Carsten; Golla, Paulina; Gericke, Marion; Eden, Gabriele; Beutel, Gernot; Schmidt, Julius J; Schmidt, Bernhard M W; De Reys, Stef; Kielstein, Jan T

2016-01-01

Therapeutic plasma exchange (TPE) is either performed using a highly permeable filter with standard multifunctional renal replacement equipment (mTPE) or a centrifugation device (cTPE). Although both techniques are well established in clinical practice, performance of these two modes of TPE was never compared in a prospective randomized fashion. Thus we aimed to compare two commercially available therapeutic apheresis systems: mTPE (Octonova with Plasmaflo filter) and cTPE (Spectra Optia apheresis system). Twenty-one patients (age 51.6 ± 13.5 years; 10 F/11 M; BMI 25.1 ± 5.0 kg/m(2)) were enrolled in this randomized, prospective, paired, crossover study performed in the Hannover Medical School, Germany. First treatment (either mTPE or cTPE) was chosen by an online randomization list. The primary endpoints were plasma removal efficiency with 1.2× of the total plasma volume exchanged. Secondary endpoints were total amount of plasma substances removed, such as IgG and fibrinogen. Further, the treatment effect on platelet count and complications were evaluated. Despite a comparable volume of the processed plasma, mTPE treatment time was 10.5 % longer than cTPE treatment time (p centrifugal procedures were conducted using flow rates that could easily be obtained using peripheral access, plasma removal efficiency was significantly higher and treatment time was significantly lower in cTPE as compared to mTPE. Despite this lower treatment time, the decline in markers of procedure efficacy was comparable. Especially in centers performing many procedures per year, cTPE in contrast to mTPE can reduce treatment time without compromising treatment efficacy.

Treating TTP/HUS with plasma exchange: a single centre's 25-year experience.

Science.gov (United States)

Forzley, Brian R; Sontrop, Jessica M; Macnab, Jennifer J; Chen, Salina; Clark, William F

2008-10-01

Thrombotic thrombocytopenic purpura/Haemolytic uremic syndrome (TTP/HUS) is a thrombotic microangiopathy with a 6-month mortality rate of 16-29%. The present study described the clinical features, treatment regime and 6-month all-cause mortality rate of TTP/HUS patients at the London Health Sciences Centre (LHSC), Canada. Data for this retrospective cohort study were obtained from inpatient and outpatient records for all patients referred for plasma exchange therapy at LHSC, Canada between 1981 and 2006. Patients (n = 110) were categorized as: idiopathic primary (38%) or relapsed (16%), and secondary responsive (30%) or non-responsive (16%). Mortality data were available for all but three patients. The all-cause 6-month mortality rate was 19% overall and was 12% and 26% among idiopathic and secondary TTP/HUS patients, respectively. No mortality events occurred among the 17 idiopathic patients who relapsed. Relapsed patients had the least severe presenting characteristics, the fastest response time, and experienced significant improvement in the severity of clinical features between the first and final presentation. These findings suggest an excellent outcome for relapsed TTP/HUS patients. Patient education, surveillance, and aggressive plasma exchange therapy are hypothesized to improve the likelihood of survival: these hypotheses should be tested in a randomized controlled trial.

Tube Plugging Criterion for the TPCCW Heat Exchanger of Yonggwang NPP 1 and 2

International Nuclear Information System (INIS)

Kim, Hyung Nam; Yoo, Hyun Ju; Choi, Sung Nam; Song, Seok Yoon

2009-01-01

The turbine plant component cooling water(TPCCW) system circulates the cooling water to cool the components in the turbine building and discharges the heat from the components through the TPCCW heat exchanger. Recently, Yonggwang NPP 1 and 2 replaced the TPCCW heat exchanger because of tube degradation. The tubing material of new TPCCW heat exchanger of Yonggwang NPP 1 and 2 is titanium. If the tube wall cannot withstand the pressure, the cooling water with the chemicals flows into the tube side and it is discharged to the open water. The chemicals can pollute the open water. Therefore, the tubes of the TPCCW heat exchanger should be inspected and degraded tubes should be plugged. It is inevitable for the materials of the components to be degraded as the power plants become older. The degradation accompanies increasing maintenance cost as well as creating safety issues. The materials and wall thickness of heat exchanger tubes in nuclear power plants are selected to withstand system temperature, pressure, and corrosion. However, tubes have experienced leaks and failures and plugged based upon eddy current testing (ET) results. There are some problems for plugging the heat exchanger tubes since the criterion and its basis are not clearly described. For this reason, the criteria for the tube wall thickness are addressed in order to operate the heat exchangers in nuclear power plant without trouble during the cycle. There are many codes and standards to be referred for calculating the minimum thickness of the heat exchanger tube in the designing stage. However, the codes and standards related to show the tube plugging criteria may not exist currently. In this paper, a method to establish the tube plugging criteria of BOP heat exchangers, which is based on the USNRC Regulatory Guide 1.121, is introduced and the tube plugging criteria for the TPCCW heat exchanger of Yonggwang NPP No. 1 and 2. This method relies on the similar plugging criteria used in the steam generator

Tube Plugging Criterion for the TPCCW Heat Exchanger of Yonggwang NPP 1 and 2

Energy Technology Data Exchange (ETDEWEB)

Kim, Hyung Nam; Yoo, Hyun Ju; Choi, Sung Nam; Song, Seok Yoon [Korea Electric Power Research Institute, Daejeon (Korea, Republic of)

2009-05-15

The turbine plant component cooling water(TPCCW) system circulates the cooling water to cool the components in the turbine building and discharges the heat from the components through the TPCCW heat exchanger. Recently, Yonggwang NPP 1 and 2 replaced the TPCCW heat exchanger because of tube degradation. The tubing material of new TPCCW heat exchanger of Yonggwang NPP 1 and 2 is titanium. If the tube wall cannot withstand the pressure, the cooling water with the chemicals flows into the tube side and it is discharged to the open water. The chemicals can pollute the open water. Therefore, the tubes of the TPCCW heat exchanger should be inspected and degraded tubes should be plugged. It is inevitable for the materials of the components to be degraded as the power plants become older. The degradation accompanies increasing maintenance cost as well as creating safety issues. The materials and wall thickness of heat exchanger tubes in nuclear power plants are selected to withstand system temperature, pressure, and corrosion. However, tubes have experienced leaks and failures and plugged based upon eddy current testing (ET) results. There are some problems for plugging the heat exchanger tubes since the criterion and its basis are not clearly described. For this reason, the criteria for the tube wall thickness are addressed in order to operate the heat exchangers in nuclear power plant without trouble during the cycle. There are many codes and standards to be referred for calculating the minimum thickness of the heat exchanger tube in the designing stage. However, the codes and standards related to show the tube plugging criteria may not exist currently. In this paper, a method to establish the tube plugging criteria of BOP heat exchangers, which is based on the USNRC Regulatory Guide 1.121, is introduced and the tube plugging criteria for the TPCCW heat exchanger of Yonggwang NPP No. 1 and 2. This method relies on the similar plugging criteria used in the steam generator

ORGANIZATIONAL, LEGAL AND TECHNOLOGICAL ASPECTS OF HEALTH INFORMATION EXCHANGE

Directory of Open Access Journals (Sweden)

N. A. Karasev

2017-01-01

Full Text Available The article discusses organizational and legal aspects of electronic health information exchange in developed countries, particularly, introduction of electronic medical records in the United States and Europe, as well as topical issues related to standardization of information technologies in health care. We briefly describe the most popular standards used in e-medicine, such as Digital Imaging and Communications in Medicine (DICOM, openEHR and HL7. The questions of syntactic and semantic interoperability in the exchange of electronic medical records and some aspects of the digital signature use are also considered. We suggest mechanisms for implementation of electronic document management and sharing of digital medical information, as one of the most important directions of information technologies in health care. It is noted that today, the main limiting factor in providing the digital exchange of health information in Russian Federation is unresolved legal issues, i.e. the absence of a legal framework of electronic medical records share. At the same time, the level of IT development in our country is quite sufficient to meet current challenges. It is stated that, despite the unresolved number of problems (for example, completeness of medical data on a patient, given to relatives in critical situations, the adoption of a single electronic card is able to bring medical care to a new level, especially in emergency and urgent medicine.

Toward the First Data Acquisition Standard in Synthetic Biology.

Science.gov (United States)

Sainz de Murieta, Iñaki; Bultelle, Matthieu; Kitney, Richard I

2016-08-19

This paper describes the development of a new data acquisition standard for synthetic biology. This comprises the creation of a methodology that is designed to capture all the data, metadata, and protocol information associated with biopart characterization experiments. The new standard, called DICOM-SB, is based on the highly successful Digital Imaging and Communications in Medicine (DICOM) standard in medicine. A data model is described which has been specifically developed for synthetic biology. The model is a modular, extensible data model for the experimental process, which can optimize data storage for large amounts of data. DICOM-SB also includes services orientated toward the automatic exchange of data and information between modalities and repositories. DICOM-SB has been developed in the context of systematic design in synthetic biology, which is based on the engineering principles of modularity, standardization, and characterization. The systematic design approach utilizes the design, build, test, and learn design cycle paradigm. DICOM-SB has been designed to be compatible with and complementary to other standards in synthetic biology, including SBOL. In this regard, the software provides effective interoperability. The new standard has been tested by experiments and data exchange between Nanyang Technological University in Singapore and Imperial College London.

The Global Genome Biodiversity Network (GGBN) Data Standard specification

Science.gov (United States)

Droege, G.; Barker, K.; Seberg, O.; Coddington, J.; Benson, E.; Berendsohn, W. G.; Bunk, B.; Butler, C.; Cawsey, E. M.; Deck, J.; Döring, M.; Flemons, P.; Gemeinholzer, B.; Güntsch, A.; Hollowell, T.; Kelbert, P.; Kostadinov, I.; Kottmann, R.; Lawlor, R. T.; Lyal, C.; Mackenzie-Dodds, J.; Meyer, C.; Mulcahy, D.; Nussbeck, S. Y.; O'Tuama, É.; Orrell, T.; Petersen, G.; Robertson, T.; Söhngen, C.; Whitacre, J.; Wieczorek, J.; Yilmaz, P.; Zetzsche, H.; Zhang, Y.; Zhou, X.

2016-01-01

Genomic samples of non-model organisms are becoming increasingly important in a broad range of studies from developmental biology, biodiversity analyses, to conservation. Genomic sample definition, description, quality, voucher information and metadata all need to be digitized and disseminated across scientific communities. This information needs to be concise and consistent in today’s ever-increasing bioinformatic era, for complementary data aggregators to easily map databases to one another. In order to facilitate exchange of information on genomic samples and their derived data, the Global Genome Biodiversity Network (GGBN) Data Standard is intended to provide a platform based on a documented agreement to promote the efficient sharing and usage of genomic sample material and associated specimen information in a consistent way. The new data standard presented here build upon existing standards commonly used within the community extending them with the capability to exchange data on tissue, environmental and DNA sample as well as sequences. The GGBN Data Standard will reveal and democratize the hidden contents of biodiversity biobanks, for the convenience of everyone in the wider biobanking community. Technical tools exist for data providers to easily map their databases to the standard. Database URL: http://terms.tdwg.org/wiki/GGBN_Data_Standard PMID:27694206

Exchange of transverse plasmons and electrical conductivity of neutron star cores

International Nuclear Information System (INIS)

Shternin, P. S.

2008-01-01

We study the electrical conductivity in magnetized neutron star cores produced by collisions between charged particles. We take into account the ordinary exchange of longitudinal plasmons and the exchange of transverse plasmons in collisions between particles. The exchange of transverse plasmons is important for collisions between relativistic particles, but it has been disregarded previously when calculating the electrical conductivity. We show that taking this exchange into account changes the electrical conductivity, including its temperature dependence (thus, for example, the temperature dependence of the electrical resistivity along the magnetic field in the low-temperature limit takes the form R parallel ∝ T 5/3 instead of the standard dependence R parallel ∝ T 2 for degenerate Fermi systems). We briefly describe the effect of possible neutron and proton superfluidity in neutron star cores on the electrical conductivity and discuss various scenarios for the evolution of neutron star magnetic fields

Health information exchange: national and international approaches.

Science.gov (United States)

Vest, Joshua R

2012-01-01

Health information exchange (HIE), the process of electronically moving patient-level information between different organizations, is viewed as a solution to the fragmentation of data in health care. This review provides a description of the current state of HIE in seven nations, as well was three international HIE efforts, with a particular focus on the relation of exchange efforts to national health care systems, common challenges, and the implications of cross-border information sharing. National and international efforts highlighted in English language informatics journals, professional associations, and government reports are described. Fully functioning HIE is not yet a common phenomenon worldwide. However, multiple nations see the potential benefits of HIE and that has led to national and international efforts of varying scope, scale, and purview. National efforts continue to work to overcome the challenges of interoperability, record linking, insufficient infrastructures, governance, and interorganizational relationships, but have created architectural strategies, oversight agencies, and incentives to foster exchange. The three international HIE efforts reviewed represent very different approaches to the same problem of ensuring the availability of health information across borders. The potential of HIE to address many cost and quality issues will ensure HIE remains on many national agendas. In many instances, health care executives and leaders have opportunities to work within national programs to help shape local exchange governance and decide technology partners. Furthermore, HIE raises policy questions concerning the role of centralized planning, national identifiers, standards, and types of information exchanged, each of which are vital issues to individual health organizations and worthy of their attention.

Secondary Containment Design for the LLNL B801 Diala Oil Tank

Energy Technology Data Exchange (ETDEWEB)

Mertesdorf, E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2016-12-14

Design is to add an extension to the secondary containment of tank T1-A3 at building 801. Piping from the inner tank penetrates the secondary containment tank below the liquid level of the primary tank. To meet Oil Pollution Prevention Regulation 40 CFR 120.7 the single wall piping needs to be provided with secondary containment. Steel Tank Institute (STI) conference publication states: §112.3(d)(1)(iii) –SPCC Plan requirements- Systems shall be designed in accordance with good engineering practice, including consideration of applicable industry standards and that procedures for required inspections and testing have been established. Section 112.7(a)(2) allows for deviations from specific rule requirements, provided the Owner/operator responsible to select, document and implement alternate measure and a PE certifies the SPCC Plan in accordance with good engineering practices, including consideration of industry standards

Process and device for stage by stage enrichment of deuterium and/or tritium in a material suitable for isotope exchange of deuterium and tritium with hydrogen

International Nuclear Information System (INIS)

Iniotakis, N.; Decken, C.B. von der.

1983-01-01

Water containing deuterium and/or tritium is first introduced into a carrier gas flow and reduced for the stage by stage enrichment of deuterium and/or tritium. A hydrogen partial pressure of a maximum of 100 millibar is set in the carrier gas flow. The carrier gas flow is taken along the primary side of an exchange wall suitable for the permeation of hydrogen, and a further carrier gas flow flows on its secondary side, which contains water or hydrogen. Reaction products formed after isotope exchange of deuterium and/or tritium with hydrogen are removed by the secondary carrier gas flow. (orig./HP) [de

Standards to open and interoperable digital libraries

Directory of Open Access Journals (Sweden)

Luís Fernando Sayão

2007-12-01

Full Text Available Interoperability is one of the main issues in creating a networked system of digital libraries. However, the interoperability as the way to accomplish data exchange and service collaboration requires adoption of a set of open standards covering all digital repository processes. The aim of this document is to revise the most important standards, protocols and the best pratices that form the framework to an open and fully interoperable digital library.

An Improved Parametrized Representation of the Secondary He Neutral Flow in its Source Region

Science.gov (United States)

Wood, Brian E.

2017-09-01

Analysis of data from the Interstellar Boundary EXplorer (IBEX) has revealed the presence of a flow of neutral helium through the inner solar system that most likely emanates from the outer heliosheath, where a distinct population of neutral He is produced by charge exchange processes. This secondary He flow has been modeled using codes designed to study interstellar flows through the heliosphere, but a laminar flow is not a good approximation for the outer heliosheath. I present a simple parametrization for a more appropriate divergent flow, and demonstrate how the secondary He particles might provide a means to remotely measure the divergence of the ISM flow around the heliopause.

Search for R-Parity Breaking Sneutrino Exchange at LEP

CERN Document Server

Acciarri, M; Aguilar-Benítez, M; Ahlen, S P; Alcaraz, J; Alemanni, G; Allaby, James V; Aloisio, A; Alverson, G; Alviggi, M G; Ambrosi, G; Anderhub, H; Andreev, V P; Angelescu, T; Anselmo, F; Arefev, A; Azemoon, T; Aziz, T; Bagnaia, P; Baksay, L; Banerjee, S; Banerjee, Sw; Banicz, K; Barczyk, A; Barillère, R; Barone, L; Bartalini, P; Baschirotto, A; Basile, M; Battiston, R; Bay, A; Becattini, F; Becker, U; Behner, F; Berdugo, J; Berges, P; Bertucci, B; Betev, B L; Bhattacharya, S; Biasini, M; Biland, A; Bilei, G M; Blaising, J J; Blyth, S C; Bobbink, Gerjan J; Böck, R K; Böhm, A; Boldizsar, L; Borgia, B; Bourilkov, D; Bourquin, Maurice; Braccini, S; Branson, J G; Brigljevic, V; Brock, I C; Buffini, A; Buijs, A; Burger, J D; Burger, W J; Busenitz, J K; Button, A M; Cai, X D; Campanelli, M; Capell, M; Cara Romeo, G; Carlino, G; Cartacci, A M; Casaus, J; Castellini, G; Cavallari, F; Cavallo, N; Cecchi, C; Cerrada-Canales, M; Cesaroni, F; Chamizo-Llatas, M; Chang, Y H; Chaturvedi, U K; Chekanov, S V; Chemarin, M; Chen, A; Chen, G; Chen, G M; Chen, H F; Chen, H S; Chéreau, X J; Chiefari, G; Chien, C Y; Cifarelli, Luisa; Cindolo, F; Civinini, C; Clare, I; Clare, R; Cohn, H O; Coignet, G; Colijn, A P; Colino, N; Commichau, V; Costantini, S; Cotorobai, F; de la Cruz, B; Csilling, Akos; Dai, T S; D'Alessandro, R; De Asmundis, R; Degré, A; Deiters, K; Della Volpe, D; Denes, P; De Notaristefani, F; DiBitonto, Daryl; Diemoz, M; Van Dierendonck, D N; Di Lodovico, F; Dionisi, C; Dittmar, Michael; Dominguez, A; Doria, A; Dova, M T; Duchesneau, D; Duinker, P; Durán, I; Dutta, S; Easo, S; Efremenko, Yu V; El-Mamouni, H; Engler, A; Eppling, F J; Erné, F C; Ernenwein, J P; Extermann, Pierre; Fabre, M; Faccini, R; Falciano, S; Favara, A; Fay, J; Fedin, O; Felcini, Marta; Fenyi, B; Ferguson, T; Ferroni, F; Fesefeldt, H S; Fiandrini, E; Field, J H; Filthaut, Frank; Fisher, P H; Fisk, I; Forconi, G; Fredj, L; Freudenreich, Klaus; Furetta, C; Galaktionov, Yu; Ganguli, S N; García-Abia, P; Gau, S S; Gentile, S; Gheordanescu, N; Giagu, S; Goldfarb, S; Goldstein, J; Gong, Z F; Gougas, Andreas; Gratta, Giorgio; Grünewald, M W; Gupta, V K; Gurtu, A; Gutay, L J; Hartmann, B; Hasan, A; Hatzifotiadou, D; Hebbeker, T; Hervé, A; Van Hoek, W C; Hofer, H; Hong, S J; Hoorani, H; Hou, S R; Hu, G; Innocente, Vincenzo; Jenkes, K; Jin, B N; Jones, L W; de Jong, P; Josa-Mutuberria, I; Kasser, A; Khan, R A; Kamrad, D; Kamyshkov, Yu A; Kapustinsky, J S; Karyotakis, Yu; Kaur, M; Kienzle-Focacci, M N; Kim, D; Kim, D H; Kim, J K; Kim, S C; Kim, Y G; Kinnison, W W; Kirkby, A; Kirkby, D; Kirkby, Jasper; Kiss, D; Kittel, E W; Klimentov, A; König, A C; Kopp, A; Korolko, I; Koutsenko, V F; Krämer, R W; Krenz, W; Kunin, A; Ladrón de Guevara, P; Laktineh, I; Landi, G; Lapoint, C; Lassila-Perini, K M; Laurikainen, P; Lebeau, M; Lebedev, A; Lebrun, P; Lecomte, P; Lecoq, P; Le Coultre, P; Lee, H J; Le Goff, J M; Leiste, R; Leonardi, E; Levchenko, P M; Li Chuan; Lin, C H; Lin, W T; Linde, Frank L; Lista, L; Liu, Z A; Lohmann, W; Longo, E; Lu, W; Lü, Y S; Lübelsmeyer, K; Luci, C; Luckey, D; Luminari, L; Lustermann, W; Ma Wen Gan; Maity, M; Majumder, G; Malgeri, L; Malinin, A; Maña, C; Mangeol, D J J; Mangla, S; Marchesini, P A; Marin, A; Martin, J P; Marzano, F; Massaro, G G G; McNally, D; McNeil, R R; Mele, S; Merola, L; Meschini, M; Metzger, W J; Von der Mey, M; Mi, Y; Mihul, A; Van Mil, A J W; Milcent, H; Mirabelli, G; Mnich, J; Molnár, P; Monteleoni, B; Moore, R; Morganti, S; Moulik, T; Mount, R; Müller, S; Muheim, F; Muijs, A J M; Nahn, S; Napolitano, M; Nessi-Tedaldi, F; Newman, H; Niessen, T; Nippe, A; Nisati, A; Nowak, H; Oh, Yu D; Opitz, H; Organtini, G; Ostonen, R; Palomares, C; Pandoulas, D; Paoletti, S; Paolucci, P; Park, H K; Park, I H; Pascale, G; Passaleva, G; Patricelli, S; Paul, T; Pauluzzi, M; Paus, C; Pauss, Felicitas; Peach, D; Pei, Y J; Pensotti, S; Perret-Gallix, D; Petersen, B; Petrak, S; Pevsner, A; Piccolo, D; Pieri, M; Piroué, P A; Pistolesi, E; Plyaskin, V; Pohl, M; Pozhidaev, V; Postema, H; Produit, N; Prokofev, D; Prokofiev, D O; Rahal-Callot, G; Raja, N; Rancoita, P G; Rattaggi, M; Raven, G; Razis, P A; Read, K; Ren, D; Rescigno, M; Reucroft, S; Van Rhee, T; Riemann, S; Riles, K; Robohm, A; Rodin, J; Roe, B P; Romero, L; Rosier-Lees, S; Rosselet, P; Van Rossum, W; Roth, S; Rubio, Juan Antonio; Ruschmeier, D; Rykaczewski, H; Salicio, J; Sánchez, E; Sanders, M P; Sarakinos, M E; Sarkar, S; Sassowsky, M; Schäfer, C; Shchegelskii, V; Schmidt-Kärst, S; Schmitz, D; Schmitz, P; Scholz, N; Schopper, Herwig Franz; Schotanus, D J; Schwenke, J; Schwering, G; Sciacca, C; Sciarrino, D; Servoli, L; Shevchenko, S; Shivarov, N; Shoutko, V; Shukla, J; Shumilov, E; Shvorob, A V; Siedenburg, T; Son, D; Sopczak, André; Smith, B; Spillantini, P; Steuer, M; Stickland, D P; Stone, A; Stone, H; Stoyanov, B; Strässner, A; Strauch, K; Sudhakar, K; Sultanov, G G; Sun, L Z; Susinno, G F; Suter, H; Swain, J D; Tang, X W; Tauscher, Ludwig; Taylor, L; Ting, C C; Ting, S M; Tonutti, M; Tonwar, S C; Tóth, J; Tully, C; Tuchscherer, H; Tung, K L; Uchida, Y; Ulbricht, J; Uwer, U; Valente, E; Van de Walle, R T; Vesztergombi, G; Vetlitskii, I; Viertel, Gert M; Vivargent, M; Völkert, R; Vogel, H; Vogt, H; Vorobev, I; Vorobyov, A A; Vorvolakos, A; Wadhwa, M; Wallraff, W; Wang, J C; Wang, X L; Wang, Z M; Weber, A; Wittgenstein, F; Wu, S X; Wynhoff, S; Xu, J; Xu, Z Z; Yang, B Z; Yang, C G; Yao, X Y; Ye, J B; Yeh, S C; You, J M; Zalite, A; Zalite, Yu; Zemp, P; Zeng, Y; Zhang, Z; Zhang, Z P; Zhou, B; Zhu, G Y; Zhu, R Y; Zichichi, Antonino; Ziegler, F

1997-01-01

We report on a search for R--parity breaking effects due to supersymmetric tau--sneutrino exchange in the reactions e+e- to e+e- and e+e- to mu+mu- at centre--of--mass energies from 91~{\\GeV} to 172~{\\GeV}, using the L3 detector at LEP. No evidence for deviations from the Standard Model expectations of the measured cross sections and forward--backward asymmetries for these reactions is found. Upper limits for the couplings $\\lambda_{131}$ and $\\lambda_{232}$ for sneutrino masses up to $m_{\\SNT} \\leq 190~\\GeV$ are determined from an analysis of the expected effects due to tau sneutrino exchange.

Secondary Waste Considerations for Vitrification of Sodium-Bearing Waste at the Idaho Nuclear Technology and Engineering Center FY-2001 Status Report

International Nuclear Information System (INIS)

Herbst, A.K.; Kirkham, R.J.; Losinski, S.J.

2002-01-01

The Idaho Nuclear Technology and Engineering Center (INTEC) is considering vitrification to process liquid sodium-bearing waste. Preliminary studies were completed to evaluate the potential secondary wastes from the melter off-gas clean up systems. Projected secondary wastes comprise acidic and caustic scrubber solutions, HEPA filters, activated carbon, and ion exchange media. Possible treatment methods, waste forms, and disposal sites are evaluated from radiological and mercury contamination estimates

Secondary Waste Considerations for Vitrification of Sodium-Bearing Waste at the Idaho Nuclear Technology and Engineering Center FY-2001 Status Report

Energy Technology Data Exchange (ETDEWEB)

Herbst, A.K.; Kirkham, R.J.; Losinski, S.J.

2002-09-26

The Idaho Nuclear Technology and Engineering Center (INTEC) is considering vitrification to process liquid sodium-bearing waste. Preliminary studies were completed to evaluate the potential secondary wastes from the melter off-gas clean up systems. Projected secondary wastes comprise acidic and caustic scrubber solutions, HEPA filters, activated carbon, and ion exchange media. Possible treatment methods, waste forms, and disposal sites are evaluated from radiological and mercury contamination estimates.

Secondary Waste Considerations for Vitrification of Sodium-Bearing Waste at the Idaho Nuclear Techology and Engineering Center FY-2001 Status Report

Energy Technology Data Exchange (ETDEWEB)

Herbst, Alan Keith; Kirkham, Robert John; Losinski, Sylvester John

2001-09-01

The Idaho Nuclear Technology and Engineering Center (INTEC) is considering vitrification to process liquid sodium-bearing waste. Preliminary studies were completed to evaluate the potential secondary wastes from the melter off-gas clean up systems. Projected secondary wastes comprise acidic and caustic scrubber solutions, HEPA filters, activated carbon, and ion exchange media. Possible treatment methods, waste forms, and disposal sites are evaluated from radiological and mercury contamination estimates.

assessing participation in secondary education quality enhancement

African Journals Online (AJOL)

PROF. BARTH EKWEME

for low parents and communities involvement in secondary education-quality improvement. It was recommended that the quality of instruction in ... concern on standard of education hinges on the quality of instruction the children are ... NTI, 2000). This implies that teachers have a duty of helping students under their care to.

Electrically switched cesium ion exchange. FY 1997 annual report

International Nuclear Information System (INIS)

Lilga, M.A.; Orth, R.J.; Sukamto, J.P.H.

1997-09-01

This paper describes the Electrically Switched Ion Exchange (ESIX) separation technology being developed as an alternative to ion exchange for removing radionuclides from high-level waste. Progress in FY 1997 for specific applications of ESIX is also outlined. The ESIX technology, which combines ion exchange and electrochemistry, is geared toward producing electroactive films that are highly selective, regenerable, and long lasting. During the process, ion uptake and elution can be controlled directly by modulating the potential of an ion exchange film that has been electrochemically deposited onto a high surface area electrode. This method adds little sodium to the waste stream and minimizes the secondary wastes associated with traditional ion exchange techniques. Development of the ESIX process is well underway for cesium removal using ferrocyanides as the electroactive films. Films having selectivity for perrhenate (a pertechnetate surrogate) over nitrate also have been deposited and tested. Based on the ferrocyanide film capacity, stability, rate of uptake, and selectivity shown during performance testing, it appears possible to retain a consistent rate of removal and elute cesium into the same elution solution over several load/unload cycles. In batch experiments, metal hexacyanoferrate films showed high selectivities for cesium in concentrated sodium solutions. Cesium uptake was unaffected by Na/Cs molar ratios of up to 2 x 10 4 , and reached equilibrium within 18 hours. During engineering design tests using 60 pores per inch, high surface area nickel electrodes, nickel ferrocyanide films displayed continued durability. losing less than 20% of their capacity after 1500 load/unload cycles. Bench-scale flow system studies showed no change in capacity or performance of the ESIX films at a flow rate up to 13 BV/h, the maximum flow rate tested, and breakthrough curves further supported once-through waste processing. 9 refs., 24 figs

Potential Ramifications of Common Core State Standards Adoption on Information Literacy

Directory of Open Access Journals (Sweden)

Jacob Paul Eubanks

2014-07-01

Full Text Available In the United States, the decline in jobs for high school educated workers and the proliferation of jobs for post-secondary educated workers is driving the development of the Common Core State Standards. The Common Core State Standards theoretically shift K-12 pedagogy towards ability development of critical and extended thinking skills, preparing high school graduates for college and career readiness. This literature review explores the reasoning behind the shift to the Common Core State Standards and asks questions regarding the potential ramifications their adoption might have on post-secondary information literacy instruction.

Ion exchange equilibrium constants

CERN Document Server

Marcus, Y

2013-01-01

Ion Exchange Equilibrium Constants focuses on the test-compilation of equilibrium constants for ion exchange reactions. The book first underscores the scope of the compilation, equilibrium constants, symbols used, and arrangement of the table. The manuscript then presents the table of equilibrium constants, including polystyrene sulfonate cation exchanger, polyacrylate cation exchanger, polymethacrylate cation exchanger, polysterene phosphate cation exchanger, and zirconium phosphate cation exchanger. The text highlights zirconium oxide anion exchanger, zeolite type 13Y cation exchanger, and

Evolution of Secondary Software Businesses: Understanding Industry Dynamics

Science.gov (United States)

Tyrväinen, Pasi; Warsta, Juhani; Seppänen, Veikko

Primary software industry originates from IBM's decision to unbundle software-related computer system development activities to external partners. This kind of outsourcing from an enterprise internal software development activity is a common means to start a new software business serving a vertical software market. It combines knowledge of the vertical market process with competence in software development. In this research, we present and analyze the key figures of the Finnish secondary software industry, in order to quantify its interaction with the primary software industry during the period of 2000-2003. On the basis of the empirical data, we present a model for evolution of a secondary software business, which makes explicit the industry dynamics. It represents the shift from internal software developed for competitive advantage to development of products supporting standard business processes on top of standardized technologies. We also discuss the implications for software business strategies in each phase.

Password-only authenticated three-party key exchange with provable security in the standard model.

Science.gov (United States)

Nam, Junghyun; Choo, Kim-Kwang Raymond; Kim, Junghwan; Kang, Hyun-Kyu; Kim, Jinsoo; Paik, Juryon; Won, Dongho

2014-01-01

Protocols for password-only authenticated key exchange (PAKE) in the three-party setting allow two clients registered with the same authentication server to derive a common secret key from their individual password shared with the server. Existing three-party PAKE protocols were proven secure under the assumption of the existence of random oracles or in a model that does not consider insider attacks. Therefore, these protocols may turn out to be insecure when the random oracle is instantiated with a particular hash function or an insider attack is mounted against the partner client. The contribution of this paper is to present the first three-party PAKE protocol whose security is proven without any idealized assumptions in a model that captures insider attacks. The proof model we use is a variant of the indistinguishability-based model of Bellare, Pointcheval, and Rogaway (2000), which is one of the most widely accepted models for security analysis of password-based key exchange protocols. We demonstrated that our protocol achieves not only the typical indistinguishability-based security of session keys but also the password security against undetectable online dictionary attacks.

Password-Only Authenticated Three-Party Key Exchange with Provable Security in the Standard Model

Directory of Open Access Journals (Sweden)

Junghyun Nam

2014-01-01

Full Text Available Protocols for password-only authenticated key exchange (PAKE in the three-party setting allow two clients registered with the same authentication server to derive a common secret key from their individual password shared with the server. Existing three-party PAKE protocols were proven secure under the assumption of the existence of random oracles or in a model that does not consider insider attacks. Therefore, these protocols may turn out to be insecure when the random oracle is instantiated with a particular hash function or an insider attack is mounted against the partner client. The contribution of this paper is to present the first three-party PAKE protocol whose security is proven without any idealized assumptions in a model that captures insider attacks. The proof model we use is a variant of the indistinguishability-based model of Bellare, Pointcheval, and Rogaway (2000, which is one of the most widely accepted models for security analysis of password-based key exchange protocols. We demonstrated that our protocol achieves not only the typical indistinguishability-based security of session keys but also the password security against undetectable online dictionary attacks.

Modeling and simulation of control system response to temperature disturbances in a coupled heat exchangers-AHTR system

International Nuclear Information System (INIS)

Skavdahl, I.; Utgikar, V.P.; Christensen, R.; Sabharwall, P.; Chen, M.; Sun, X.

2016-01-01

Highlights: • Control architecture defined for nuclear reactor-coupled heat exchangers system. • MATLAB code developed for simulation of system response for various temperature disturbances in the system. • Control system effective in maintaining controlled variables at desired set points. • New equilibrium steady state established using controllers. • Adaptive control system capable of switching manipulated variables based on system constraints. - Abstract: An effective control strategy is essential for maintaining optimum operational efficiency of the Advanced High Temperature Reactor (AHTR)-intermediate heat exchanger (IHX)-secondary heat exchanger (SHX) system for power conversion or process heat applications. A control system design is presented in this paper for the control of the coupled intermediate and secondary heat exchangers. The cold side outlet temperature of the SHX (T_c_o) and the hot side outlet temperature of the IHX (T_h_o_2) were identified as the controlled variables that were maintained at their set points by manipulating the flow rates of heat exchange media. Transfer functions describing the relationships between the controlled variables and the manipulated and load variables were developed and the system response to various temperature disturbances was simulated using a custom-developed MATLAB program. It was found that a step disturbance of ±10 °C in the process loop changed the thermal duty by ±650 kW, equal to 6.5% of the initial duty. Similar disturbances in the primary loop had a higher impact on the system. The control system design included a provision for the switching of manipulated variables to limit the adjustment in the magnitudes of the primary manipulated variables. Simulation results indicate that the controlled variables are maintained successfully at their desired points by the control system.

Modeling and simulation of control system response to temperature disturbances in a coupled heat exchangers-AHTR system

Energy Technology Data Exchange (ETDEWEB)

Skavdahl, I. [Department of Chemical and Materials Engineering, University of Idaho, Moscow, ID 83844 (United States); Utgikar, V.P., E-mail: vutgikar@uidaho.edu [Department of Chemical and Materials Engineering, University of Idaho, Moscow, ID 83844 (United States); Christensen, R. [Nuclear Engineering Program, University of Idaho, Idaho Falls, ID 83402 (United States); Sabharwall, P. [Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Chen, M.; Sun, X. [Nuclear Engineering Program, Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH 43210 (United States)

2016-04-15

Highlights: • Control architecture defined for nuclear reactor-coupled heat exchangers system. • MATLAB code developed for simulation of system response for various temperature disturbances in the system. • Control system effective in maintaining controlled variables at desired set points. • New equilibrium steady state established using controllers. • Adaptive control system capable of switching manipulated variables based on system constraints. - Abstract: An effective control strategy is essential for maintaining optimum operational efficiency of the Advanced High Temperature Reactor (AHTR)-intermediate heat exchanger (IHX)-secondary heat exchanger (SHX) system for power conversion or process heat applications. A control system design is presented in this paper for the control of the coupled intermediate and secondary heat exchangers. The cold side outlet temperature of the SHX (T{sub co}) and the hot side outlet temperature of the IHX (T{sub ho2}) were identified as the controlled variables that were maintained at their set points by manipulating the flow rates of heat exchange media. Transfer functions describing the relationships between the controlled variables and the manipulated and load variables were developed and the system response to various temperature disturbances was simulated using a custom-developed MATLAB program. It was found that a step disturbance of ±10 °C in the process loop changed the thermal duty by ±650 kW, equal to 6.5% of the initial duty. Similar disturbances in the primary loop had a higher impact on the system. The control system design included a provision for the switching of manipulated variables to limit the adjustment in the magnitudes of the primary manipulated variables. Simulation results indicate that the controlled variables are maintained successfully at their desired points by the control system.

Interactive Data Visualization for HIV Cohorts: Leveraging Data Exchange Standards to Share and Reuse Research Tools.

Directory of Open Access Journals (Sweden)

Meridith Blevins

Full Text Available To develop and disseminate tools for interactive visualization of HIV cohort data.If a picture is worth a thousand words, then an interactive video, composed of a long string of pictures, can produce an even richer presentation of HIV population dynamics. We developed an HIV cohort data visualization tool using open-source software (R statistical language. The tool requires that the data structure conform to the HIV Cohort Data Exchange Protocol (HICDEP, and our implementation utilized Caribbean, Central and South America network (CCASAnet data.This tool currently presents patient-level data in three classes of plots: (1 Longitudinal plots showing changes in measurements viewed alongside event probability curves allowing for simultaneous inspection of outcomes by relevant patient classes. (2 Bubble plots showing changes in indicators over time allowing for observation of group level dynamics. (3 Heat maps of levels of indicators changing over time allowing for observation of spatial-temporal dynamics. Examples of each class of plot are given using CCASAnet data investigating trends in CD4 count and AIDS at antiretroviral therapy (ART initiation, CD4 trajectories after ART initiation, and mortality.We invite researchers interested in this data visualization effort to use these tools and to suggest new classes of data visualization. We aim to contribute additional shareable tools in the spirit of open scientific collaboration and hope that these tools further the participation in open data standards like HICDEP by the HIV research community.

Specification of a STEP Based Reference Model for Exchange of Robotics Models

DEFF Research Database (Denmark)

Haenisch, Jochen; Kroszynski, Uri; Ludwig, Arnold

robot programming, the descriptions of geometry, kinematics, robotics, dynamics, and controller data using STEP are addressed as major goals of the project.The Project Consortium has now released the "Specificatin of a STEP Based Reference Model for Exchange of Robotics Models" on which a series......ESPRIT Project 6457: "Interoperability of Standards for Robotics in CIME" (InterRob) belongs to the Subprogram "Computer Integrated Manufacturing and Engineering" of ESPRIT, the European Specific Programme for Research and Development in Information Technology supported by the European Commision....... InterRob aims to develop an integrated solution to precision manufacturing by combining product data and database technologies with robotic off-line programming and simulation. Benefits arise from the use of high level simulation tools and developing standards for the exchange of product model data...

75 FR 80866 - Credit Rating Standardization Study

Science.gov (United States)

2010-12-23

... commenters believe that market stress conditions can be defined in a consistent manner across different... Securities and Exchange Commission is requesting public comment to help inform its study pursuant to Section... ratings using identical terms; standardizing the market stress conditions under which ratings are...

Calibration of photon and beta ray sources used in brachytherapy. Guidelines on standardized procedures at Secondary Standards Dosimetry Laboratories (SSDLs) and hospitals

International Nuclear Information System (INIS)

2002-03-01

It has generally been recognized that international harmonization in radiotherapy dosimetry is essential. Consequently, the IAEA has given much effort to this, for example by publishing a number of reports in the Technical Reports Series (TRS) for external beam dosimetry, most notably TRS-277 and more recently TRS-398. Both of these reports describe in detail the steps to be taken for absorbed dose determination in water and they are often referred to as 'dosimetry protocols'. Similar to TRS-277, it is expected that TRS-398 will be adopted or used as a model by a large number of countries as their national protocol. In 1996, the IAEA established a calibration service for low dose rate (LDR) 137 Cs brachytherapy sources, which is the most widely used source for treatment of gynecological cancer. To further enhance harmonization in brachytherapy dosimetry, the IAEA published in 1999 IAEA-TECDOC-1079 entitled 'Calibration of Brachytherapy Sources. Guidelines on Standardized Procedures for the Calibration of Brachytherapy Sources at Secondary Standard Dosimetry Laboratories (SSDLs) and Hospitals'. The report was well received and was distributed in a large number of copies to the members of the IAEA/WHO network of SSDLs and to medical physicists working with brachytherapy. The present report is an update of the aforementioned TECDOC. Whereas TECDOC-1079 described methods for calibrating brachytherapy sources with photon energies at or above those of 192 Ir, the current report has a wider scope in that it deals with standardization of calibration of all the most commonly used brachytherapy sources, including both photon and beta emitting sources. The latter sources have been in use for a few decades already, but their calibration methods have been unclear. Methods are also described for calibrating sources used in the rapidly growing field of cardiovascular angioplasty. In this application, irradiation of the vessel wall is done in an attempt to prevent restenosis after

Does exchange of information between tax authorities influence multinationals' use of tax havens?

OpenAIRE

Braun, Julia; Weichenrieder, Alfons

2015-01-01

Since the mid-1990s, countries offering tax systems that facilitate international tax avoidance and evasion have been facing growing political pressure to comply with the internationally agreed standards of exchange of tax information. Using data of German investments in tax havens, we find evidence that the conclusion of a bilateral tax information exchange agreement (TIEA) is associated with fewer operations in tax havens and the number of German affiliates has on average ...

HIV cohort collaborations: proposal for harmonization of data exchange

DEFF Research Database (Denmark)

Kjær, Jesper; Ledergerber, Bruno

2004-01-01

than can be achieved with the individual studies. This requires each cohort to map data into a standard format before merging. Until recently, this standard format has differed for each such collaborative analysis. We have therefore developed the HIV Cohort Data Exchange Protocol (HICDEP), which...... is freely available at http://www.cphiv.dk/HICDEP.pdf. Once individual cohorts have set up a means of transfering data into this format, as and when required, this should greatly facilitate data merging for future joint analyses. The HICDEP incorporates data from HIV drug resistance tests, which have been...

Explaining employment relationships with social exchange and job embeddedness.

Science.gov (United States)

Hom, Peter W; Tsui, Anne S; Wu, Joshua B; Lee, Thomas W; Zhang, Ann Yan; Fu, Ping Ping; Li, Lan

2009-03-01

The research reported in this article clarifies how employee-organization relationships (EORs) work. Specifically, the authors tested whether social exchange and job embeddedness mediate how mutual-investment (whereby employers offer high inducements to employees for their high contributions) and over-investment (high inducements without corresponding high expected contributions) EOR approaches, which are based on Tsui, Pearce, Porter, and Tripoli's (1997) framework, affect quit propensity and organizational commitment. Two studies evaluated these intervening mechanisms. Study 1 surveyed 953 Chinese managers attending part-time master of business administration (MBA) programs in China, whereas Study 2 collected cross-sectional and longitudinal data from 526 Chinese middle managers in 41 firms. Standard and multilevel causal modeling techniques affirmed that social exchange and job embeddedness translate EOR influence. A second multilevel test using lagged outcome measures further established that job embeddedness mediates long-term EOR effects over 18 months. These findings corroborate prevailing views that social exchange explains how mutual- and over-investment EORs motivate greater workforce commitment and loyalty. This study enriches EOR perspectives by identifying job embeddedness as another mediator that is more enduring than social exchange. (c) 2009 APA, all rights reserved.

40 CFR 421.204 - Standards of performance for new sources.

Science.gov (United States)

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Mercury... Secondary Mercury Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average mg/kg (pounds per million pounds) of mercury produced from batteries Lead 0.030 0.014 Mercury 0...

Exchange rate policy

Directory of Open Access Journals (Sweden)

Plačkov Slađana

2013-01-01

Full Text Available Small oscillations of exchange rate certainly affect the loss of confidence in the currency (Serbian dinar, CSD and because of the shallow market even the smallest change in the supply and demand leads to a shift in exchange rate and brings uncertainty. Some economists suggest that the course should be linked to inflation and thus ensure predictable and stable exchange rates. Real exchange rate or slightly depressed exchange rate will encourage the competitiveness of exporters and perhaps ensure the development of new production lines which, in terms of overvalued exchange rate, had no economic justification. Fixed exchange rate will bring lower interest rates, lower risk and lower business uncertainty (uncertainty avoidance, but Serbia will also reduce foreign exchange reserves by following this trend. On the other hand, a completely free exchange rate, would lead to a (real fall of Serbian currency, which in a certain period would lead to a significant increase in exports, but the consequences for businessmen and citizens with loans pegged to the euro exchange rate, would be disastrous. We will pay special attention to the depreciation of the exchange rate, as it is generally favorable to the export competitiveness of Serbia and, on the other hand, it leads to an increase in debt servicing costs of the government as well as of the private sector. Oscillations of the dinar exchange rate, appreciation and depreciation, sometimes have disastrous consequences on the economy, investors, imports and exports. In subsequent work, we will observe the movement of the dinar exchange rate in Serbia, in the time interval 2009-2012, in order to strike a balance and maintain economic equilibrium. A movement of foreign currencies against the local currency is controlled in the foreign exchange market, so in case economic interests require, The National Bank of Serbia (NBS, on the basis of arbitrary criteria, can intervene in the market.

Standardized Curriculum for Automotive Mechanics.

Science.gov (United States)

Mississippi State Dept. of Education, Jackson. Office of Vocational, Technical and Adult Education.

Standardized curricula are provided for two courses for the secondary vocational education program in Mississippi: automotive mechanics I and II. The six units in automotive mechanics I are as follows: orientation and safety; tools, equipment, and manuals; measurement; automotive engines; basic electrical systems; and fuel systems. Automotive…

Exchange market pressure

NARCIS (Netherlands)

Jager, H.; Klaassen, F.; Durlauf, S.N.; Blume, L.E.

2010-01-01

Currencies can be under severe pressure in the foreign exchange market, but in a fixed (or managed) exchange rate regime that is not fully visible via the change in the exchange rate. Exchange market pressure (EMP) is a concept developed to nevertheless measure the pressure in such cases. This

Fundamental experiment of potassium heat exchanger using principle of heat pipe

International Nuclear Information System (INIS)

Sumida, Isao; Kotani, Koichi

1976-01-01

In order to provide compact and reliable sodium equipments including a steam generator, performance tests are conducted with a potassium heat exchanger, which is featured by the separate construction of primary and secondary coolant systems. A small amount of potassium plays a role as an intermediate media of heat transportation between these two coolant systems. Heat is transferred by evaporation and condensation of potassium on the surface of the primary and the secondary coolant pipings, respectively. The tests are performed in the temperature range of 200 -- 300 0 C and the maximum heat transfer reaches 1.3kW (heat transfer rate at the primary heating source: 8.6W/cm 2 at 300 0 C). The experimental results are analyzed by using Langmuir's and Schrage's equation and close agreement between experiment and theory is obtained. (auth.)

Experimental Study on the Airside Performance of Aluminum Heat Exchangers Having Slim Louver Fins

Energy Technology Data Exchange (ETDEWEB)

Kim, Nae Hyun [Incheon Nat’l Univ., Incheon (Korea, Republic of); Cho, Honggi [Samsung Electronics Daejeon, Suwon (Korea, Republic of)

2017-09-15

Recent trends in slim air conditioners require heat exchangers of reduced flow depth. In this study, slim louver fin geometry was obtained using predictive correlations. The deduced geometry yielded 10 mm flow depth, 0.9 mm louver pitch, and 35° louver angle. Samples were made and tests were conducted. The new slim sample yielded 36% higher j factor and 2.3% higher f factor compared with those of the standard sample. This implies that 26% reduction of heat exchanger volume was possible by reducing the flow depth. In addition, the j/f1/3 of the slim sample was 55% larger than that of the standard sample. Furthermore, the results are compared with predictions made using existing correlations.

Experimental Study on the Airside Performance of Aluminum Heat Exchangers Having Slim Louver Fins

International Nuclear Information System (INIS)

Kim, Nae Hyun; Cho, Honggi

2017-01-01

Recent trends in slim air conditioners require heat exchangers of reduced flow depth. In this study, slim louver fin geometry was obtained using predictive correlations. The deduced geometry yielded 10 mm flow depth, 0.9 mm louver pitch, and 35° louver angle. Samples were made and tests were conducted. The new slim sample yielded 36% higher j factor and 2.3% higher f factor compared with those of the standard sample. This implies that 26% reduction of heat exchanger volume was possible by reducing the flow depth. In addition, the j/f1/3 of the slim sample was 55% larger than that of the standard sample. Furthermore, the results are compared with predictions made using existing correlations.

New Standards Require Teaching More Statistics: Are Preservice Secondary Mathematics Teachers Ready?

Science.gov (United States)

Lovett, Jennifer N.; Lee, Hollylynne S.

2017-01-01

Mathematics teacher education programs often need to respond to changing expectations and standards for K-12 curriculum and accreditation. New standards for high school mathematics in the United States include a strong emphasis in statistics. This article reports results from a mixed methods cross-institutional study examining the preparedness of…

The DICOM Standard: A Brief Overview

Science.gov (United States)

Gibaud, Bernard

The DICOM standard has now become the uncontested standard for the exchange and management of biomedical images. Everyone acknowledges its prominent role in the emergence of multi-vendor Picture Archiving and Communication Systems (PACS), and their successful integration with Hospital Information Systems and Radiology Information Systems, thanks to the Integrating the Healthcare Enterprise (IHE) initiative. We introduce here the basic concepts retained for the definition of objects and services in DICOM, with the hope that it will help the reader to find his or her way in the vast DICOM documentation available on the web.

Discussion of the origin of secondary photon and secondary ion emission during energetic particle irradiation of solids. I. The collision cascade

International Nuclear Information System (INIS)

Wright, R.B.; Gruen, D.M.

1980-01-01

Secondary photon and secondary ion emission during energetic particle irradiation of solid surfaces is assumed to arise due to excitation and de-excitation of sputtered particles originating from a collision cascade induced by the incident projectile. The excitation is postulated to occur by two alternative mechanisms: path (a), where excitation occurs at or very near the surface of the solid due to atom--atom or atom--electron collisions; and path (b), where excitation occurs as the sputtered particle leaves the solid, but is still under its influence so that electron exchange processes are permitted. Once the excited and/or ionized sputtered particle is formed nonradiative de-excitation processes are then included in the discussion which allow the excited and/or ionized particle to be de-excited and/or neutralized. The result of these nonradiative de-excitation processes is shown to provide a possible channel for the formation of new excited ''daughters'' by the de-excitation of the initial excited ''parent''. Depending on the initial excitation probability of the parent the new excited daughters are shown to contribute to various energy regions of the excited and/or ionized secondary particle energy distribution. A mathematical formalism is developed based on the neutral sputtered atom energy and velocity distributions assuming a collision cascade origin for these sputtered particles. By including various models for the excitation probability, and the survival probability for excited particles once formed to not undergo nonradiative de-excitation the resulting energy and velocity distributions of the sputtered excited and/or ionized secondary particles are calculated. These distributions are found to be a function of the emission angle depending on the model assumed for the initial excitation. From this formalism the total excited secondary particle yield may be calculated

Consequences of Secondary Calibrations on Divergence Time Estimates.

Directory of Open Access Journals (Sweden)

John J Schenk

Full Text Available Secondary calibrations (calibrations based on the results of previous molecular dating studies are commonly applied in divergence time analyses in groups that lack fossil data; however, the consequences of applying secondary calibrations in a relaxed-clock approach are not fully understood. I tested whether applying the posterior estimate from a primary study as a prior distribution in a secondary study results in consistent age and uncertainty estimates. I compared age estimates from simulations with 100 randomly replicated secondary trees. On average, the 95% credible intervals of node ages for secondary estimates were significantly younger and narrower than primary estimates. The primary and secondary age estimates were significantly different in 97% of the replicates after Bonferroni corrections. Greater error in magnitude was associated with deeper than shallower nodes, but the opposite was found when standardized by median node age, and a significant positive relationship was determined between the number of tips/age of secondary trees and the total amount of error. When two secondary calibrated nodes were analyzed, estimates remained significantly different, and although the minimum and median estimates were associated with less error, maximum age estimates and credible interval widths had greater error. The shape of the prior also influenced error, in which applying a normal, rather than uniform, prior distribution resulted in greater error. Secondary calibrations, in summary, lead to a false impression of precision and the distribution of age estimates shift away from those that would be inferred by the primary analysis. These results suggest that secondary calibrations should not be applied as the only source of calibration in divergence time analyses that test time-dependent hypotheses until the additional error associated with secondary calibrations is more properly modeled to take into account increased uncertainty in age estimates.

EXTERNALITIES IN EXCHANGE NETWORKS AN ADAPTATION OF EXISTING THEORIES OF EXCHANGE NETWORKS

NARCIS (Netherlands)

Dijkstra, Jacob

2009-01-01

The present paper extends the focus of network exchange research to externalities in exchange networks. Externalities of exchange are defined as direct effects on an actor's utility, of an exchange in which this actor is not involved. Existing theories in the field of network exchange do not inform

OGC Consensus: How Successful Standards Are Made

Directory of Open Access Journals (Sweden)

Carl Reed

2015-09-01

Full Text Available This paper describes the history, background, and current status of the Open Geospatial Consortium (OGC standards development consensus process. The roots of the formation of the OGC lie in the early 1990s when a very strong market requirement for exchanging GIS data content was clearly stated. At that time, each GIS vendor had their own formats for publishing and/or exchanging their GIS data. There was no mechanism or organization that provided a forum for the GIS vendors and GIS data users to collaborate and agree on how to share GIS data. That requirement, along with the vision of a few individuals, led to the formation of the OGC. This paper describes the early development of the consensus process in the OGC, how this process has evolved over time, why consensus is so important for defining open standards that are implemented in the marketplace, and the future of the OGC consensus process.

Leakage monitoring and maintenance for main heat-exchanger of project 871

International Nuclear Information System (INIS)

Li Yanshui; Cao Zhibin

1995-01-01

Main heat-exchanger is one of the most important equipment. To prevent the occurrence of leakage accident, desalting and water treatment for secondary cooling water is conducted chemical except controlling the water quality of coolant. There is a small loop for leakage monitoring to find out the leakage immediately. In order to ensure the safety of operation, the treatment of eliminating water dirt and inspection for outside and inside must be done periodically, and the relevant means must be adopted if any abnormal phenomenon is found

78 FR 19552 - Self-Regulatory Organizations; Chicago Board Options Exchange, Incorporated; Notice of Filing and...

Science.gov (United States)

2013-04-01

... that deliver 10 physical shares on SPDR S&P 500 (``SPY''), Apple, Inc. (``AAPL''), SPDR Gold Trust... CBOE Rule 5.5.22. Standard equity and exchange-traded fund (``ETF'') option contracts have a unit of... contract characteristics as standard equity and ETF options, including exercise style. Accordingly, the...

78 FR 4936 - Self-Regulatory Organizations; Chicago Stock Exchange, Inc.; Notice of Filing of Amendment No. 3...

Science.gov (United States)

2013-01-23

... corporate governance practices differ from those followed by domestic companies under CHX-listing standards...), ``Corporate Governance--Compensation Committee;'' and Rule 19(p)(3), ``Corporate Governance--Definitions... many of CHX's corporate governance listing standards, including the Exchange's compensation-related...

Dual cell conductivity during ionic exchange processes: the intelligent transmitter EXA DC 400

International Nuclear Information System (INIS)

Mier, A.

1997-01-01

Why is differential conductivity important versus standard conductivity measurement? That entirely depends on the application. If we have a process where the conductivity changes ge.. Cation exchanger, then standard conductivity measurement is not appropriate. With dual cell conductivity we can rate the process and eliminate conductivity changes outside the process. Therefore we achieve more precise control or monitoring of that process. (Author)

Estimating Exchange Market Pressure and the Degree of Exchange Market Intervention for Finland during the Floating Exchange Rate Regime

OpenAIRE

Pösö, Mika; Spolander, Mikko

1997-01-01

In this paper, we use a fairly simple monetary macro model to calculate the quarterly measures of exchange market pressure and the degree of the Bank of Finland's intervention during the time the markka was floated. Exchange market pressure measures the size of the exchange rate change that would have occurred if the central bank had unexpectedly refrained from intervening in the foreign exchange market. Intervention activity of the central bank is measured as the proportion of exchange marke...

Maintenance of the CERN telephone exchanges

CERN Multimedia

2007-01-01

Maintenance work will be carried out on the CERN telephone exchanges between 8 p.m. and midnight on 20 November. Fixed-line telephone and audioconference services may be disrupted while the work is being carried out. However, the CCC and the fire brigade will be contactable at any time. Mobile telephony services (GSM) will not be affected by the maintenance work. For further details about the maintenance work, please contact the telephone switchboard on 76111 or by email to standard.telephone@cern.ch. Telecom Section IT/CS

PREDICTION OF TOTAL DISSOLVED GAS EXCHANGE AT HYDROPOWER DAMS

Energy Technology Data Exchange (ETDEWEB)

Hadjerioua, Boualem [ORNL; Pasha, MD Fayzul K [ORNL; Stewart, Kevin M [ORNL; Bender, Merlynn [Bureau of Reclamation; Schneider, Michael L. [U.S. Army Corps of Engineers

2012-07-01

Total dissolved gas (TDG) supersaturation in waters released at hydropower dams can cause gas bubble trauma in fisheries resulting in physical injuries and eyeball protrusion that can lead to mortality. Elevated TDG pressures in hydropower releases are generally caused by the entrainment of air in spillway releases and the subsequent exchange of atmospheric gasses into solution during passage through the stilling basin. The network of dams throughout the Columbia River Basin (CRB) are managed for irrigation, hydropower production, flood control, navigation, and fish passage that frequently result in both voluntary and involuntary spillway releases. These dam operations are constrained by state and federal water quality standards for TDG saturation which balance the benefits of spillway operations designed for Endangered Species Act (ESA)-listed fisheries versus the degradation to water quality as defined by TDG saturation. In the 1970s, the United States Environmental Protection Agency (USEPA), under the federal Clean Water Act (Section 303(d)), established a criterion not to exceed the TDG saturation level of 110% in order to protect freshwater and marine aquatic life. The states of Washington and Oregon have adopted special water quality standards for TDG saturation in the tailrace and forebays of hydropower facilities on the Columbia and Snake Rivers where spillway operations support fish passage objectives. The physical processes that affect TDG exchange at hydropower facilities have been studied throughout the CRB in site-specific studies and routine water quality monitoring programs. These data have been used to quantify the relationship between project operations, structural properties, and TDG exchange. These data have also been used to develop predictive models of TDG exchange to support real-time TDG management decisions. These empirically based predictive models have been developed for specific projects and account for both the fate of spillway and

Identification of some cross flow heat exchanger dynamic responses by measurement with low level binary pseudo-random input signals

International Nuclear Information System (INIS)

Corran, E.R.; Cummins, J.D.; Hopkinson, A.

1964-02-01

An experiment was performed to assess the usefulness of the binary cross-correlation method in the context of the identification problem. An auxiliary burner was excited with a discrete interval binary code and the response to the perturbation of the input heat was observed by recording the variations of the primary inlet, primary outlet and secondary outlet temperatures. The observations were analysed to yield cross-correlation functions and frequency responses were subsequently determined between primary inlet and primary outlet temperatures and also between primary inlet and secondary outlet temperatures. The analysis verified (1) that these dynamic responses of this cross flow heat exchanger may be predicted theoretically, (2) in so far as this heat exchanger is representative of the generality of plant, that the binary cross-correlation method provides adequate identification of plant dynamics for control purposes in environments where small input variations and low signal to noise ratio are obligatory. (author)

A continuous exchange factor method for radiative exchange in enclosures with participating media

International Nuclear Information System (INIS)

Naraghi, M.H.N.; Chung, B.T.F.; Litkouhi, B.

1987-01-01

A continuous exchange factor method for analysis of radiative exchange in enclosures is developed. In this method two types of exchange functions are defined, direct exchange function and total exchange function. Certain integral equations relating total exchange functions to direct exchange functions are developed. These integral equations are solved using Gaussian quadrature integration method. The results obtained based on the present approach are found to be more accurate than those of the zonal method

The overall heat transfer characteristics of a double pipe heat exchanger: comparison of experimental data with predictions of standard correlations

International Nuclear Information System (INIS)

Mehrabian, M. A.; Mansouri, S. H.; Sheikhzadeh, G. A.

2002-01-01

The single-phase flow and thermal performance of a double pipe heat exchanger are examined by experimental methods. The working fluid is water at atmospheric pressure. Temperature measurements at the inlet and outlet of the two streams and also at an intermediate point half way between the inlet and outlet is made, using copper-constantan thermocouple wires. Mass flow rates for each stream are also measured using calibrated ratemeters. Heat is supplied to the inner tube stream by an immersion heater. The overall heat transfer coefficients are inferred from the measured data. The heat transfer coefficient of the inner tube flow (circular cross section) is calculated using the standard correlations. The heat transfer coefficient of the outer tube flow (annular cross section) is then deduced.Higher heat transfer coefficients are reported in the laminar flow regime in comparison to the predictions of standard correlations for straight and smooth tubes. The reasons for this discrepancy are identified and discussed. Experimental errors in measuring temperatures and mass flow rates are studied and their effects on the heat transfer coefficients are estimated. Experimental results for the range of operating conditions used in this work show that the outer tube side heat transfer coefficients are smaller than the inner side heat transfer coefficients by a factor of almost 1.5 and 3.4 in counter flow and parallel flow arrangements, respectively. The agreement with predictions is very good for the counter flow arrangement, but not very good for the parallel flow arrangement

Electron exchange reaction in anion exchangers as observed in uranium isotope separation

International Nuclear Information System (INIS)

Obanawa, Heiichiro; Takeda, Kunihiko; Seko, Maomi

1991-01-01

The mechanism of electron exchange in an ion exchanger, as occurring between U 4+ and UO 2 2+ in uranium isotope separation, was investigated. The height of the separation unit (H q ) in the presence of metal ion catalysts, as obtained from the separation experiments, was found to be almost coincident with the theoretical value of H q as calculated on the basis of the intrasolution acceleration mechanism of the metal ion, suggesting that the electron exchange mechanism in the ion-exchanger is essentially the same as that in the solution when metal ion catalysts are present. Separation experiments with no metal ion catalyst, on the other hand, showed the electron exchange reaction in the ion exchanger to be substantially higher than that in the solution, suggesting an acceleration of the electron exchange reaction by the ion-exchanger which is due to the close existence of higher order Cl - complexes of UO 2 2+ and U 4+ in the vicinity of the ion-exchange group. (author)

Interoperability of Standards for Robotics in CIME

DEFF Research Database (Denmark)

Kroszynski, Uri; Sørensen, Torben; Ludwig, Arnold

1997-01-01

Esprit Project 6457 "Interoperability of Standards for Robotics in CIME (InterRob)" belongs to the Subprogramme "Integration in Manufacturing" of Esprit, the European Specific Programme for Research and Development in Information Technology supported by the European Commision.The first main goal...... of InterRob was to close the information chain between product design, simulation, programming, and robot control by developing standardized interfaces and their software implementation for standards STEP (International Standard for the Exchange of Product model data, ISO 10303) and IRL (Industrial Robot...... Language, DIN 66312). This is a continuation of the previous Esprit projects CAD*I and NIRO, which developed substantial basics of STEP.The InterRob approach is based on standardized models for product geometry, kinematics, robotics, dynamics and control, hence on a coherent neutral information model...

Investigation of Chemical Exchange at Intermediate Exchange Rates using a Combination of Chemical Exchange Saturation Transfer (CEST) and Spin-Locking methods (CESTrho)

Science.gov (United States)

Kogan, Feliks; Singh, Anup; Cai, Keija; Haris, Mohammad; Hariharan, Hari; Reddy, Ravinder

2011-01-01

Proton exchange imaging is important as it allows for visualization and quantification of the distribution of specific metabolites with conventional MRI. Current exchange mediated MRI methods suffer from poor contrast as well as confounding factors that influence exchange rates. In this study we developed a new method to measure proton exchange which combines chemical exchange saturation transfer (CEST) and T1ρ magnetization preparation methods (CESTrho). We demonstrated that this new CESTrho sequence can detect proton exchange in the slow to intermediate exchange regimes. It has a linear dependence on proton concentration which allows it to be used to quantitatively measure changes in metabolite concentration. Additionally, the magnetization scheme of this new method can be customized to make it insensitive to changes in exchange rate while retaining its dependency on solute concentration. Finally, we showed the feasibility of using CESTrho in vivo. This sequence is able to detect proton exchange at intermediate exchange rates and is unaffected by the confounding factors that influence proton exchange rates thus making it ideal for the measurement of metabolites with exchangeable protons in this exchange regime. PMID:22009759

Investigation of chemical exchange at intermediate exchange rates using a combination of chemical exchange saturation transfer (CEST) and spin-locking methods (CESTrho).

Science.gov (United States)

Kogan, Feliks; Singh, Anup; Cai, Keija; Haris, Mohammad; Hariharan, Hari; Reddy, Ravinder

2012-07-01

Proton exchange imaging is important as it allows for visualization and quantification of the distribution of specific metabolites with conventional MRI. Current exchange mediated MRI methods suffer from poor contrast as well as confounding factors that influence exchange rates. In this study we developed a new method to measure proton exchange which combines chemical exchange saturation transfer and T(1)(ρ) magnetization preparation methods (CESTrho). We demonstrated that this new CESTrho sequence can detect proton exchange in the slow to intermediate exchange regimes. It has a linear dependence on proton concentration which allows it to be used to quantitatively measure changes in metabolite concentration. Additionally, the magnetization scheme of this new method can be customized to make it insensitive to changes in exchange rate while retaining its dependency on solute concentration. Finally, we showed the feasibility of using CESTrho in vivo. This sequence is able to detect proton exchange at intermediate exchange rates and is unaffected by the confounding factors that influence proton exchange rates thus making it ideal for the measurement of metabolites with exchangeable protons in this exchange regime. Copyright © 2011 Wiley Periodicals, Inc.

QuakeML: status of the XML-based seismological data exchange format

OpenAIRE

Joachim Saul; Philipp Kästli; Fabian Euchner; Danijel Schorlemmer

2011-01-01

QuakeML is an XML-based data exchange standard for seismology that is in its fourth year of active community-driven development. Its development was motivated by the need to consolidate existing data formats for applications in statistical seismology, as well as setting a cutting-edge, community-agreed standard to foster interoperability of distributed infrastructures. The current release (version 1.2) is based on a public Request for Comments process and accounts for suggestions and comments...

On one pion exchange potential with quark exchange in the resonating group method

International Nuclear Information System (INIS)

Braeuer, K.; Faessler, A.; Fernandez, F.; Shimizu, K.

1985-01-01

The effect of quark exchange between different nucleons on the one pion exchange potential is studied in the framework of the resonating group method. The calculated phase shifts including the one pion exchange potential with quark exchange in addition to the one gluon plus sigma meson exchange are shown to be consistent with experiments. Especially the p-wave phase shifts are improved by taking into account the quark exchange on the one pion exchange potential. (orig.)

Evidence that cyclophosphamide can to induce exchanges in the sister chromatids (ICH) through secondary injuries

International Nuclear Information System (INIS)

Morales R, P.; Rodriguez R, R.

1997-01-01

By means of the use of destination protocol of ICH inductive injuries (DLI-ICH), it was studied if interchanges in the sister chromatids (ICH) induced by cyclophosphamide (CP), in the second post-treatment division (ICH-2) are produced by secondary injuries or by fresh injuries. For discard between these possibilities it was administered CP at different periods before of the first post-treatment division, taking as reference the administered time for high dose of bromodeoxyuridine (BrdU ) which was approximately at the beginning of this division. The ICH frequencies that occur in the first, the second and the third synthesis stages (S) were determined. It was observed that when the administered CP was four hours before BrdU , the ICH frequencies of the second and the third S were reduced. The frequency of the first ICH increased lightly in relation to those of the normal protocol (0.5 h before BrdU ) and that the supplying of CP six hours before caused almost a total reduction of ICH of second and third S and an important increment of ICH of first S.This was interpreted as evidence that the ICH-2 are product of secondary injuries. (Author)

Exchange current contributions to quasi-elastic electron scattering

International Nuclear Information System (INIS)

Conte, J.S. Jr.

1981-01-01

Because electromagnetic interactions are weak and well understood, inelastic electron scattering has been very useful in elucidating aspects of nuclear structure. In the region of large electron energy loss, an extremely simple reaction picture (quasi-free knockout of a single nucleon or electroproduction of an isobar) and a simple nuclear model (Fermi gas) have provided both a good fit to experimental data and a dynamical determination of the nuclear Fermi momentum (k/sub F/). However, there exists an anomalous region where this picture fails. Two body correlations have not seemed to help give any better agreement. We have investigated the following questions: Do exchange current processes contribute importantly in this region. Do they help produce agreement with experiment. Also, how do they effect our previous picture of quasifree knockout. We calculate the effects of exchange currents in this region using the standard Feynman graph rules. We have included all important long range exchange currents: pair, pionic, and isobar exchange currents. We found it necessary to make non-relativistic reductions of these currents in order to facilitate calculations. The resulting multidimensional integrals were done using Monte Carlo techniques. All exchange currents which were investigated were found to be appreciable in the anomalous region, and also important in the quasi-free peak region. Inclusion of these amplitudes would supply all of the missing cross section in the anomalous region: however, it would destroy the agreement between theory and experiment in the region of the quasi-free nucleon peak, and thereby cast suspicion on the aforementioned dynamical determination of k/sub F/

CFD analysis of the two-phase bubbly flow characteristics in helically coiled rectangular and circular tube heat exchangers

Science.gov (United States)

Hussain, Alamin; Fsadni, Andrew M.

2016-03-01

Due to their ease of manufacture, high heat transfer efficiency and compact design, helically coiled heat exchangers are increasingly being adopted in a number of industries. The higher heat transfer efficiency over straight pipes is due to the secondary flow that develops as a result of the centrifugal force. In spite of the widespread use of helically coiled heat exchangers, and the presence of bubbly two-phase flow in a number of systems, very few studies have investigated the resultant flow characteristics. This paper will therefore present the results of CFD simulations for the two-phase bubbly flow in helically coiled heat exchangers as a function of the volumetric void fraction and the tube cross-section design. The CFD results are compared to the scarce flow visualisation experimental results available in the open literature.

10 CFR Appendix A to Part 440 - Standards for Weatherization Materials

Science.gov (United States)

2010-01-01

..., Washington, DC 20006; (202) 554-1080. National Institute of Standards and Technology, U.S. Department of... manufacturers' specifications. Condensing heat exchangers Commercially available (Commercial, multi-story...