Prototyping phase of the high heat flux scraper element of Wendelstein 7-X

Energy Technology Data Exchange (ETDEWEB)

Boscary, J., E-mail: jean.boscary@ipp.mpg.de [Max Planck Institute for Plasma Physics, Garching (Germany); Greuner, H. [Max Planck Institute for Plasma Physics, Garching (Germany); Ehrke, G. [Max Planck Institute for Plasma Physics, Greifswald (Germany); Böswirth, B.; Wang, Z. [Max Planck Institute for Plasma Physics, Garching (Germany); Clark, E. [University of Tennessee, Knoxville (United States); Lumsdaine, A. [Oak Ridge National Laboratory, USA National Laboratory, Oak Ridge, Tennessee (United States); Tretter, J. [Max Planck Institute for Plasma Physics, Garching (Germany); McGinnis, D.; Lore, J. [Oak Ridge National Laboratory, USA National Laboratory, Oak Ridge, Tennessee (United States); Ekici, K. [University of Tennessee, Knoxville (United States)

2016-11-01

Highlights: • Aim of scraper element: reduction of heat loads on high heat flux divertor ends. • Design: actively water-cooled for 20 MW/m{sup 2} local heat loads. • Technology: CFC NB31 monoblocks bonded by HIP to CuCrZr cooling tube. • Successful high heat flux testing up to 20 MW/m{sup 2}. - Abstract: The water-cooled high heat flux scraper element aims to reduce excessive heat loads on the target element ends of the actively cooled divertor of Wendelstein 7-X. Its purpose is to intercept some of the plasma fluxes both upstream and downstream before they reach the divertor surface. The scraper element has 24 identical plasma facing components (PFCs) divided into 6 modules. One module has 4 PFCs hydraulically connected in series by 2 water boxes. A PFC, 247 mm long and 28 mm wide, has 13 monoblocks made of CFC NB31 bonded by hot isostatic pressing onto a CuCrZr cooling tube equipped with a copper twisted tape. 4 full-scale prototypes of PFCs have been successfully tested in the GLADIS facility up to 20 MW/m{sup 2}. The difference observed between measured and calculated surface temperatures is probably due to the inhomogeneity of CFC properties. The design of the water box prototypes has been detailed to allow the junction between the cooling pipe of the PFCs and the water boxes by internal orbital welding. The prototypes are presently under fabrication.

A beam scraper using a linear motor

International Nuclear Information System (INIS)

Beadle, E.R.; Rodger, E.S.; Thern, R.E.

1989-01-01

A beam scraper using a linear motor drive has been developed for use in the AGS at Brookhaven National Laboratory. The device is used to measure beam size by moving a target to a predetermined location and measuring the intercepted beam with nearby loss monitors or by noting the decrease in the circulating beam current. This device has excellent vacuum characteristics, as the motor and sensor coils are outside the vacuum, coupled magnetically to the moving parts which, are inside. There are no bellows or dynamic seals required. The position-time profile is controlled by a closed-loop servo system which uses position feedback. 2 refs., 4 figs

A single-cell scraper based on an atomic force microscope for detaching a living cell from a substrate

Energy Technology Data Exchange (ETDEWEB)

Iwata, Futoshi, E-mail: iwata.futoshi@shizuoka.ac.jp [Department of Mechanical Engineering, Faculty of Engineering, Shizuoka University, Johoku, Naka-ku, Hamamatsu 432-8561 (Japan); Research Institute of Electronics, Shizuoka University, Johoku, Naka-ku, Hamamatsu 432-8011 (Japan); Adachi, Makoto; Hashimoto, Shigetaka [Department of Mechanical Engineering, Faculty of Engineering, Shizuoka University, Johoku, Naka-ku, Hamamatsu 432-8561 (Japan)

2015-10-07

We describe an atomic force microscope (AFM) manipulator that can detach a single, living adhesion cell from its substrate without compromising the cell's viability. The micrometer-scale cell scraper designed for this purpose was fabricated from an AFM micro cantilever using focused ion beam milling. The homemade AFM equipped with the scraper was compact and standalone and could be mounted on a sample stage of an inverted optical microscope. It was possible to move the scraper using selectable modes of operation, either a manual mode with a haptic device or a computer-controlled mode. The viability of the scraped single cells was evaluated using a fluorescence dye of calcein-acetoxymethl ester. Single cells detached from the substrate were collected by aspiration into a micropipette capillary glass using an electro-osmotic pump. As a demonstration, single HeLa cells were selectively detached from the substrate and collected by the micropipette. It was possible to recultivate HeLa cells from the single cells collected using the system.

The Development of Optimal Cryopreservation Media For Longspine Scraper (Capoeta trutta Sperm

Directory of Open Access Journals (Sweden)

Erdinç Şahinöz

2018-03-01

Full Text Available This study is performed to determine some of sperm quality after applying freezing / thawing process. Thus, the aim of this study is to examine different cryprotective agents with additives in terms of their effects at different pH on the cryopreservation process of longspine scraper (Capoeta trutta. The present study, twelve media were prepared by mixing three different cryoprotectants (dimethyl sulfoxide (DMSO, (CH32SO; methanol (CH3OH; methyl glycol (MG, CH3O (CH22OH with an extenders (glucose at four different pH (7.2, 7.6, 8.0 and 8.4 for longspine scraper semen. Considering the findings from the examination (The motility rate after thawing process and duration of motility obtained in DMSO as 81% and 20 min, in methanol as 73% and 12 min, in methyl glycol as 60% and 15 min., we can conclude that the DMSO is the best freezing media in order to create new essays in cryopreservation for sperm of Capoeta trutta in the future.

Benchmark of the SixTrack-Fluka Active Coupling Against the SPS Scrapers Burst Test

CERN Multimedia

Mereghetti, A; Cerutti, F

2014-01-01

The SPS scrapers are a key ingredient for the clean injection into the LHC: they cut off halo particles quite close to the beam core (e.g.~3.5 sigma) just before extraction, to minimise the risk for quenches. The improved beam parameters as envisaged by the LHC Injectors Upgrade (LIU) Project required a revision of the present system, to assess its suitability and robustness. In particular, a burst (i.e. endurance) test of the scraper blades has been carried out, with the whole bunch train being scraped at the centre (worst working conditions). In order to take into account the effect of betatron and longitudinal beam dynamics on energy deposition patterns, and nuclear and Coulomb scattering in the absorbing medium onto loss patterns, the SixTrack and Fluka codes have been coupled, profiting from the best of the refined physical models they respectively embed. The coupling envisages an active exchange of tracked particles between the two codes at each turn, and an on-line aperture check in SixTrack, in order ...

Design and analysis of the W7-X divertor scraper element

International Nuclear Information System (INIS)

Lumsdaine, A.; Tipton, J.; Lore, J.; McGinnis, D.; Canik, J.; Harris, J.; Peacock, A.; Boscary, J.; Tretter, J.; Andreeva, T.

2013-01-01

Highlights: • A high heat flux actively cooled divertor component is thermally modeled with CFD. • CFC monoblocks are analyzed to verify peak steady-state temperatures do not exceed 1200 °C. • A field line diffusion code is developed to determine the heat flux on the divertor components. • Iteration is required to develop a surface that meets the criteria and fits into the limited space. -- Abstract: Thehigh heat-flux divertor of the Wendelstein 7-X large stellarator experiment consists of 10 divertor units which are designed to carry a steady-state heat flux of 10 MW/m 2 . However, the edge elements of this divertor are limited to only 5 MW/m 2 , and may be overloaded in certain plasma scenarios. It is proposed to reduce this heat by placing an additional “scraper element” in each of the ten divertor locations. It will be constructed using carbon fiber composite (CFC) monoblock technology. The design of the monoblocks and the path of the cooling tubes must be optimized in order to survive the significant steady-state heat loads, provide adequate coverage for the existing divertor, be located within sub-millimeter accuracy, and take into account the boundaries to other in vessel components, all at a minimum cost. Computational fluid dynamics modeling has been performed to examine the thermal transfer through the monoblock swirl tube channels for the design of the monoblock orientation. An iterative physics modeling and computer aided design process is being performed to optimize the placement of the scraper element within the severe spatial restrictions

The scrapers of obsidian from Metztitlan, Hidalgo. Typology and tools function with the application of the Sem, PIXE and NAA techniques

International Nuclear Information System (INIS)

Elizalde R, S.V.; Mandujano A, C.

2000-01-01

In the last 50 years have been enormous changes and the archaeology has been benefited with the technology development, as computation, the advancements in nuclear physics, the electron microscopy, the particle accelerator and the DNA analysis. As first approach to studied material it was realized in cabinet the morphological and technological analysis to establish a typology and to know the manufacturer process of the scrapers (tool used for to scrape a cavity after cutting its lance-shaping leaves at the maguey core obtaining so the sap commonly named hydromel at the Hidalgo state region in Mexico). On the other hand the studies which carried out in the ININ consist in the functional analysis of use traces in scanning electron microscopy (Sem) and stereoscopic to know about the type of work which were addressed the scrapers. Also were carried out the Neutron Activation Analysis (NAA) and the Proton Induced X-ray Emission (PIXE) with the purpose to know the obsidian site which was supplied the Dominion population. (Author)

Safe Harvesting of Outer Table Parietal Bone Grafts Using an Oscillating Saw and a Bone Scraper : A Refinement of Technique for Harvesting Cortical and "Cancellous"-Like Calvarial Bone

NARCIS (Netherlands)

Schortinghuis, Jurjen; Putters, Thomas F.; Raghoebar, Gerry M.

Calvarial bone is a readily available source of bone for preimplantation augmentation procedures of the alveolar process. However, the calvaria consist mostly of cortical bone, and cancellous bone of the diploic space is scarce. A bone scraper (Safescraper Twist; META, Reggio Emilia, Italy) was used

Hide-Scrapers from Arukhlo I Settlement in Georgia (on correspondence of the shape and function of prehistoric implements

Directory of Open Access Journals (Sweden)

Esakia Ketevan M.

2017-09-01

Full Text Available The article analyses one of the primary categories of the implement complex discovered at Arukhlo I Neolithic settlement (Georgia, Kvemo Kartli Region. The stone implements discovered at the site are characterized by their great variety. Comprehensive functional research conducted by the authors demonstrated that the typological and morphological characteristics of the various categories of stone implements do not always correspond to their functions. Thus, the shapes and functions of the hide-scrapers were fully identical for 18 of 39 implements only, whereas the other tools were used for different purposes and did not feature traces of utilization. A microanalysis of their working parts allowed to determine the types of processed raw material, means of processing, and in certain cases the type of obtained articles as well. The authors made a conclusion on the importance of the comprehensive research of production inventory for the reconstruction of the characteristic features of prehistoric economy.

Nanoscratch technique for aligning multiwalled carbon nanotubes ...

Indian Academy of Sciences (India)

MWCNTs) were synthesized in an open air, without the need for a controlled atmosphere, using a rotating cathode arc discharge method with the help of a metal scraper. The physical force exerted by the scraper results in in-situ alignment of MWCNTs ...

SPS transverse beam scraping and LHC injection losses

CERN Document Server

Drosdal, L; Bartmann, W; Bracco, C; Cornelis, K; Goddard, B; Meddahi, M; Veyrunes, E

2012-01-01

Machine protection sets strict requirements for the quality of the injected beam, in particular in the transverse plane. Losses at aperture restrictions and protection elements have to be kept at a minimum. Particles in the beam tails are lost at the tight transfer line collimators and can trigger the LHC beam abort system. These particles have to be removed by scrapers in the vertical and horizontal plane in the SPS. Scraping has become vital for high intensity LHC operation. This paper shows the dependence of injection quality on the SPS scraping and discusses an improved scraper setting up strategy for better reproducibility with the current scraper system.

Life Cycle and Secondary Production of Four Species from Functional Feeding Groups in a Tropical Stream of South India

Directory of Open Access Journals (Sweden)

Sankarappan Anbalagan

2014-01-01

Full Text Available This study focused on life strategies of species from functional feeding groups (FFGs found in a tropical stream of the Sirumalai hills, South India. We examined the life cycle and secondary production of species of shredders (Lepidostoma nuburagangai, scrapers (Baetis sp., collectors (Choroterpes alagarensis, and predators (Neoperla biseriata. In addition, we studied the assemblage structure of functional feeding groups. We found the collectors occupied the highest percentage, followed in turn by scrapers, predators, and shredders. The diversity of FFGs was higher at riffle areas and assemblage with stream substrates differing in each functional group. An asynchronous life cycle was observed for Baetis, C. alagarensis, and N. biseriata, while L. nuburagangai was found in four to five generations per year. We acquired data on secondary production of scraper species of Baetis, which reached the highest values among all investigated species. This observation stresses the importance of scrapers as playing a key role in converting coarse particulate organic matter to fine particulate organic matter with low or high abundances of shredder population and maintaining the food chain in tropical streams.

Stable isotope analysis indicates a lack of inter- and intra-specific dietary redundancy among ecologically important coral reef fishes

Science.gov (United States)

Plass-Johnson, J. G.; McQuaid, C. D.; Hill, J. M.

2013-06-01

Parrotfish are critical consumers on coral reefs, mediating the balance between algae and corals, and are often categorised into three functional groups based on adult morphology and feeding behaviour. We used stable isotope analysis (δ13C, δ15N) to investigate size-related ontogenetic dietary changes in multiple species of parrotfish on coral reefs around Zanzibar. We compared signatures among species and functional groups (scrapers, excavators and browsers) as well as ontogenetic stages (immature, initial and terminal phase) within species. Stable isotope analysis suggests that ontogenetic dietary shifts occurred in seven of the nine species examined; larger individuals had enriched δ13C values, with no relationship between size and δ15N. The relationship between fish length and δ13C signature was maintained when species were categorised as scrapers and excavators, but was more pronounced for scrapers than excavators, indicating stronger ontogenetic changes. Isotopic mixing models classified the initial phase of both the most abundant excavator ( Chlorurus sordidus) as a scraper and the immature stage of the scraper Scarus ghobban (the largest species) as an excavator, indicating that diet relates to size rather than taxonomy. The results indicate that parrotfish may show similar intra-group changes in diet with length, but that their trophic ecology is more complex than suggested by morphology alone. Stable isotope analyses indicate that feeding ecology may differ among species within functional groups, and according to ontogenetic stage within a species.

Freeze concentration of lime juice

Directory of Open Access Journals (Sweden)

Ampawan Tansakul

2008-11-01

Full Text Available The main objective of this research was to study the effects of processing conditions, i.e. cooling medium temperature (-6, -12 and -18C and scraper blade rotational speed (50, 100 and 150 rpm on the freeze concentration of lime juice. The initial soluble solid content of lime juice was 7.6 Brix. Results showed that soluble solid content of lime juice increased as cooling medium temperature decreased while scraper blade rotational speed increased. It was also found that the processing condition with -18˚C cooling medium temperature and 150 rpm rotational speed of the scraper blade was the best among all studied conditions, although the loss of the soluble solids with ice crystals during ice separation was relatively high at 35%.

Distillation of shale

Energy Technology Data Exchange (ETDEWEB)

Anderson, J

1877-01-05

The retort consists of a trough fitted with a hood, the edges of which hood dip into a channel of water formed round the sides of the trough, and thereby seal the retort. The shale is introduced at one end of the hood through a double-valved inlet hopper, and is moved along the retort by transverse scrapers or paddles. At the other end it falls through a double-valved outlet upon a set of firebars which carry it along under the retort, where either alone or in admixture with other fuel it is used for heating the vessel. The vapors from the shale pass off through pipes in the hood, or an inverted channel may be formed along the center of the hood for collecting the vapors from different parts of the vessel. The scrapers are worked by rocking shafts supported on bearings in the edges of the trough, and are made to feather when moving in a direction from the discharged end. Levers from the rocking shafts project down into the water channel, where they are connected with horizontal bars made to reciprocate longitudinally by suitable means, thus working the scrapers without using stuffing-boxes. Rotating scrapers may be substituted for the reciprocating ones.

Scraping the surface

Energy Technology Data Exchange (ETDEWEB)

Petermann, L. [FAM Foerderanlagen Magdeburg (Germany)

2003-10-01

The paper studies a range of bulk materials handling equipment provided by FAM. These include a conveying system and a bridge-type scraper for the ThyssenKrupp coke plant at Schwelgern, power plant scrapers at Mai Liao, Taiwan and Ning Bo, China, a new combined bridge type stacker/reclaimer at the Port of Rijeka and a continuous ship unloader for the Coal Handling Project of Europoort-Rotterdam for which FAM has entered into a license agreement with the Japanese company SHI. 2 figs.

Beam Scraping for LHC Injection

CERN Document Server

Burkhardt, H; Fischer, C; Gras, J-J; Koschik, A; Kramer, Daniel; Pedersen, S; Redaelli, S

2007-01-01

Operation of the LHC will require injection of very high intensity beams from the SPS to the LHC. Fast scrapers have been installed and will be used in the SPS to detect and remove any existing halo before beams are extracted, to minimize the probability for quenching of superconducting magnets at injection in the LHC. We briefly review the functionality of the scraper system and report about measurements that have recently been performed in the SPS on halo scraping and re-population of tails.

Effect of root planing on surface topography: an in-vivo randomized experimental trial.

Science.gov (United States)

Rosales-Leal, J I; Flores, A B; Contreras, T; Bravo, M; Cabrerizo-Vílchez, M A; Mesa, F

2015-04-01

The root surface topography exerts a major influence on clinical attachment and bacterial recolonization after root planing. In-vitro topographic studies have yielded variable results, and clinical studies are necessary to compare root surface topography after planing with current ultrasonic devices and with traditional manual instrumentation. The aim of this study was to compare the topography of untreated single-rooted teeth planed in vivo with a curette, a piezoelectric ultrasonic (PU) scraper or a vertically oscillating ultrasonic (VOU) scraper. In a randomized experimental trial of 19 patients, 44 single-rooted teeth were randomly assigned to one of four groups for: no treatment; manual root planing with a curette; root planing with a PU scraper; or root planing with a VOU scraper. Post-treatment, the teeth were extracted and their topography was analyzed in 124 observations with white-light confocal microscopy, measuring the roughness parameters arithmetic average height, root-mean-square roughness, maximum height of peaks, maximum depth of valleys, absolute height, skewness and kurtosis. The roughness values arithmetic average height and root-mean-square roughness were similar after each treatment and lower than after no treatment ( p  0.05). Both ultrasonic devices reduce the roughness, producing a similar topography to that observed after manual instrumentation with a curette, to which they appear to represent a valid alternative. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Research on Navigation Path Planning for An Underground Load Haul Dump

Directory of Open Access Journals (Sweden)

Qi Yulong

2015-11-01

Full Text Available The improved A * algorithm is a method of navigation path planning for articulated underground scrapers. Firstly, an environment model based on a mining Geographic Information System (GIS map is established, and then combined with improved A * algorithm, the underground global path planning problem of the intelligent Load Haul Dump (LHD is solved. In this paper, for the articulated structure, the method of expanding nodes by articulation angle is adopted to make expanded nodes meet the trajectory characteristics. In addition, collision threat cost is introduced in the evaluation function to avoid collisions between the LHD and the tunnel walls. As peran analysis of the simulation test to verify the effectiveness of the improved A * algorithm and a comparison with the traditional A * algorithm, the improved A * algorithm can enhance search efficiency. Acontrast of multiple sets of test parameters suggests that when the price weighted coefficient of collision is 0.2, the shortest path can be derived to avoid impact. Finally, tracking results indicate that the proposed algorithm for navigation path planning can maintain the tracking error to within 0.2 m in line with the structural characteristics of the scraper in the laboratory environment to realize the path planning of unmanned scrapers and trajectory tracking. Moreover, the algorithm can enhance the safety of scrapers and prevent roadway collisions. The feasibility and practicality of the proposed method is verified in this work.

Active heat exchange system development for latent heat thermal energy storage

Science.gov (United States)

Alario, J.; Kosson, R.; Haslett, R.

1980-01-01

Various active heat exchange concepts were identified from among three generic categories: scrapers, agitators/vibrators and slurries. The more practical ones were given a more detailed technical evaluation and an economic comparison with a passive tube-shell design for a reference application (300 MW sub t storage for 6 hours). Two concepts were selected for hardware development: (1) a direct contact heat exchanger in which molten salt droplets are injected into a cooler counterflowing stream of liquid metal carrier fluid, and (2) a rotating drum scraper in which molten salt is sprayed onto the circumference of a rotating drum, which contains the fluid salt is sprayed onto the circumference of a rotating drum, which contains the fluid heat sink in an internal annulus near the surface. A fixed scraper blade removes the solidified salt from the surface which was nickel plated to decrease adhesion forces. In addition to improving performance by providing a nearly constant transfer rate during discharge, these active heat exchanger concepts were estimated to cost at least 25% less than the passive tube-shell design.

Mechanical lift of profile

Energy Technology Data Exchange (ETDEWEB)

O`Mahoney, H.

1999-04-01

Continuous ship unloaders (CSUs) are continuing to become more popular than grab unloaders for dealing with greater capacities of coal. The article surveys current major manufacturers` equipment. Krupp Foerdertechnik, for example, offers seven mechanical ship unloaders, including CSU with scraper chain or L-shaped bucket-elevators, CSU with vertical screw conveyor and horizontal screw-type feeder conveyors. CSU with bucket-elevator and feeding scraper and a continuous barge unloader with bucket elevator, BMH Marine Siwertell continues to be the benchmark for technology advances. HW Carlsan has recently entered the field with a new screw-type ship unloader. 4 photos.

ESTUDIOS FUNCIONALES DE ARTEFACTOS LÍTICOS DE CUEVA DE LAS MANOS, RÍO PINTURAS, SANTA CRUZ, ARGENTINA / Lithic artifacts functional studies from Cueva de las Manos, Río Pinturas, Santa Cruz, Argentina

Directory of Open Access Journals (Sweden)

G. Roxana Cattaneo

2009-12-01

Full Text Available  El presente trabajo tiene como objetivo presentar los resultados del estudio funcional o de microhuellas de una muestra de raspadores procedentes de la excavación del sitio Cueva de las Manos. Fueron seleccionados entre los provenientes de las capas 4c, 5 y 6 –que cuentan con fechados radiocarbónicos entre 1610 años AP a 9300 años AP. Por un lado nos interesó poder profundizar sobre qué materia prima trabajaron estos raspadores, ya que nunca había podido ser analizado en estudios anteriores. Por otro lado nos interesa ampliar el estudio de la variabilidad morfológica en relación a la variabilidad funcional en los raspadores ya que en este sitio es notable la variedad de instrumentos clasificados como raspadores y cepillos (rabots. Estos nuevos resultados permitirán además profundizar la discusión presentada en trabajos anteriores donde se infirió una tendencia hacia una diferenciación entre ciertos subgrupos de instrumentos cuyos últimos usos conocidos fueron sobre un solo tipo de materia prima mientras que otros se asociaron con el trabajo de al menos dos tipos de materiales. Para este trabajo se utilizaron las observaciones realizadas con el Microscopio Láser Confocal de Barrido BioRad MRC600, luego analizadas a través de software de reconocimiento de imágenes “PHILOS”.  Palabras clave: Cueva de las Manos, raspadores, análisis funcional, diseño.  AbstractWe present the results of microwear studies of a sample of scrapers, from the excavations at the site Cueva de las Manos -layers 4c, 5 and 6-, dated between 1610 bp to 9300 years bp. We are interested in defining on what type of raw material these scrapers worked, since this subject wasn’t previously analyzed. On the other hand we are interested in extending the study of the morphologic variability of scrapers, in relation to their functional variability. Especially considering that this site presents a remarkable number of instruments classified as scrapers

Halo scraper/direct converter system study

International Nuclear Information System (INIS)

Luzzi, T.; Clarkson, I.; Barr, W.; Neef, W.

1985-01-01

During the first year of the LLNL Minimars program, a system study was undertaken to determine the most efficient method for recovery of the end cell thermal energy. The goal of the study was to recovery energy at the highest possible coolant temperature and therefore at the highest thermal efficiency. Two types of coolant were considered, water and gaseous helium. In a system study where the goal is to recover maximum thermal power in an economically designed device, it is necessary to place constraints on the design. The four constraints for the direct converter are somewhat conflicting in that a particularly design solution satisfying one may lead to an unacceptable solution for another. The final design choice must be a compromise that satisfies all the constraints

The influence on biogas production of three slurry-handling systems in dairy farms

Directory of Open Access Journals (Sweden)

Damiano Coppolecchia

2015-04-01

Full Text Available Handling systems can influence the production of biogas and methane from dairy farm manures. A comparative work performed in three different Italian dairy farms showed how the most common techniques (scraper, slatted floor, flushing can change the characteristics of collected manure. Scraper appears to be the most neutral choice, as it does not significantly affect the original characteristics of manure. Slatted floor produces a manure that has a lower methane potential in comparison with scraper, due to: a lower content of volatile solids caused by the biodegradation occurring in the deep pit, and a lower specific biogas production caused by the change in the characteristics of organic matter. Flushing can produce three different fluxes: diluted flushed manure, solid separated manure and liquid separated manure. The diluted fraction appears to be unsuitable for conventional anaerobic digestion in completely stirred reactors (CSTR, since its content of organic matter is too low to be worthwhile. The liquid separated fraction could represent an interesting material, as it appears to accumulate the most biodegradable organic fraction, but not as primary substrate in CSTR as the organic matter concentration is too low. Finally, the solid-liquid separation process tends to accumulate inert matter in the solid separated fraction and, therefore, its specific methane production is low.

30 CFR 77.1109 - Quantity and location of firefighting equipment.

Science.gov (United States)

2010-07-01

... equipment such as portable drills, sweepers, and scrapers, when operated more than 600 feet from equipment... tank. (f) Vehicles transporting explosives and blasting agents shall be equipped with fire protection...

78 FR 65375 - Notice of Inventory Completion: University of Michigan, Ann Arbor, MI

Science.gov (United States)

2013-10-31

...-pointed copper awls, 1 hammer stone, 2 lithic scrapers, 1 quartz biface, 103 ceramic sherds, and 1 lot of... remains described in this notice are Native American based on cranial morphology, dental traits, accession...

Remote Excavation of Heavily Contaminated UXO Sites. The Range Master

National Research Council Canada - National Science Library

Crandall, Alan L

2007-01-01

USA Environmental, Inc., and Timberline Environmental Services, Inc., developed the Range Master, a remote controlled scraper with an integrated power screen, to excavate and sift the top 12 inches of heavily contaminated UXO sites...

Angular mining conveyor

Energy Technology Data Exchange (ETDEWEB)

Sender, A; Mura, A; Liduchowski, L; Zok, P; Skolik, W; Szyngiel, S; Rojek, H; Gajda, B; Major, M; Stanislawski, P; Sliwiok, H; Sikora, J

1988-10-19

Angular mining conveyor provided with a drag chain extending along the axis of its path of movement, and a corner member, inside which the drag chain is led in a forced way, characterized in that the drag chain, where its path curves around the corner member, is located by supporting of the vertical links of the chain along the required curved section of the conveyor path around said corner member, and the supporting line of the links is so chosen, that, within the said curved section of the conveyor path, a space is maintained between the vertical end surface of the scrapers and the outer curved surface of the radially inner side wall of a corner trough associated with the corner member, through which corner trough the scrapers pass. 10 figs.

Hearth furnace for distilling powdered materials containing hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

1937-06-21

The present invention has for its object a hearth furnace particularly intended for the distillation of powdered material containing hydrocarbons. It consists of a fixed circular hearth above which are placed the moving scrapers intended to displace the material from the center toward the periphery. The material is poured by a central vertical pipe at the base of which is arranged a rotating ring for distributing the material on the hearth; this ring, which is fastened on the vertical axis of the drive, carries the radial arms to which are attached the scrapers arranged obliquely by the support on the arms and intended to displace the material on the hearth. The hearth is heated from below by means of forced circulation of gases produced in a fire-box and maintained at a convenient temperature by mixing with a part of the cold gases.

Loads applied to fixations for chain stretching

Energy Technology Data Exchange (ETDEWEB)

Ahrens, K; Brychta, P

1985-06-01

The chains of scraper chain conveyors must be pre-stretched during standstill in order to compensate the elongations occurring during operation. They require frequent retensiening in order to meet the varying operational requirements. During tensioning, the chains are fixed in a point in the top run by means of fixation elements. The authors present a method for calculating the retaining force needed in the fixations. There are three different initial conditions of the chain before trensioning: Tensionsfree chain, pretensioned chain (stressed chain), slack chain. In all three cases, it is important to find out whether or nor the tensioning drive reaches full speed. The method of calculation is illustrated by the example of a scraper chain conveyor; it enables the establishment of rules for tensioning without damaging the chain and is a good basis for the dimensioning of new types of fixation elements.

Tokamak impurity-control techniques

International Nuclear Information System (INIS)

Schmidt, J.A.

1980-01-01

A brief review is given of the impurity-control functions in tokamaks, their relative merits and disadvantages and some prominent edge-interaction-control techniques, and there is a discussion of a new proposal, the particle scraper, and its potential advantages. (author)

Extreme Cold: A Prevention Guide to Promote Your Personal Health and Safety

Science.gov (United States)

... watch • extra batteries • non-electric can opener • snow shovel • rock salt • special needs items (diapers, hearing aid ... waterproof with heavy snow) matches (to melt • collapsible shovel snow for water) • container of water • windshield scraper ...

Methods and costs for soil removal

International Nuclear Information System (INIS)

Toomey, J.E.

1979-12-01

Surface stabilization of outdoor radiation areas is discussed. Soil transport via shovel and box, dump truck, and scraper is described. Surface preparation includes application of herbicides, fertilizers and seeds. Finally, mulch is applied to hold the seed in place until it germinates

Retorts

Energy Technology Data Exchange (ETDEWEB)

Bryson, J; Jones, J; Fraser, W

1894-04-27

The invention relates to vertical retorts for the distillation of shale and other bituminous substances, or for the calcining of ironstone etc. The retorts are circular in cross-section and have tapering lower ends. For the purpose of effecting a continuous or intermittent movement of the substance under treatment, there is mounted at the base of each retort a supporting disk or table, above which is an arm or scraper capable of being revolved by means of an upright spindle actuated by a ratchet and pawl or other means. The form of the table and scraper may be modified. The discharging hoppers of the two rows of retorts have their openings so arranged as to discharge into a single truck, which runs along a central passage underneath the retorts. Or they may discharge into a trough containing a worm, screw, or endless-band conveyer.

Frictional Forces Required for unrestrained locomotion in dairy cattle

NARCIS (Netherlands)

Tol, van der P.P.J.; Metz, J.H.M.; Noordhuizen-Stassen, E.N.; Back, W.; Braam, C.R.

2005-01-01

Most free-stall housing systems in the Netherlands are equipped with slatted or solid concrete floors with manure scrapers. A slipping incident occurs when the required coefficient of friction (RCOF) exceeds the coefficient of friction (COF) at the claw–floor interface. An experiment was conducted

Approach For Investigating Crowdfunding Campaigns With Platform Data

DEFF Research Database (Denmark)

Huhtamäki, Jukka; Lasrado, Lester; Menon, Karan

2015-01-01

and implementation of a crawler and scraper for accessing Indiegogo campaign data, and sharing this openly for other researchers. Due to the extremely dynamic and rapidly increasing amount of crowdfunding data in terms of the number of crowdfunding campaigns and the available investment and individual investor data...

Beam Scraping in the SPS for LHC Injection Efficiency and Robustness Studies

CERN Document Server

Letnes, Paul/LPA; Myrheim, Jan

2008-01-01

The Large Hadron Collider (LHC) at CERN will be the world's most powerful accelerator when it is commissioned in fall 2008. Operation of the LHC will require injection of very high intensity beams. Fast transverse beam scrapers have been installed in the Super Proton Synchrotron (SPS) injector to detect and, if necessary, remove transverse beam tails. This will help to both diagnose and prevent beam quenches in the LHC. Scraping of a high intensity beam at top energy can potentially damage the scraper jaws. This has been studied with Monte Carlo simulations to find energy deposition and limits for hardware damage. Loss maps from scraping have been generated both with machine studies and tracking simulations. Time dependent Beam Loss Monitor (BLM) measurements have shown several interesting details about the beam. An analytical model of time dependent losses is compared with beam measurements and demonstrates that beam scraping can be used to estimate the beam size. Energy deposition simulations also give the ...

Performance Evaluation of the SPS Scraping System in View of the High Luminosity LHC

CERN Document Server

AUTHOR|(SzGeCERN)659273; Cerutti, Francesco

Injection in the LHC is a delicate moment, since the LHC collimation system cannot offer adequate protection during beam transfer. For this reason, a complex chain of injection protection devices has been put in place. Among them, the SPS scrapers are the multi-turn cleaning system installed in the SPS aimed at halo removal immediately before injection in the LHC. The upgrade in luminosity of the LHC foresees beams brighter than those currently available in machine, posing serious problems to the performance of the existing injection protection systems. In particular, the integrity of beam-intercepting devices is challenged by unprecedented beam parameters, leading to interactions potentially destructive. In this context, a new design of scrapers has been proposed, aimed at improved robustness and performance. This thesis compares the two scraping systems, i.e. the existing one and the one proposed for upgrade. Unlike any other collimation system for regular halo cleaning, both are "fast" systems, characteris...

Grooved floor system for cattle housing: ammonia emission reduction and good slip resistance

NARCIS (Netherlands)

Swierstra, D.; Braam, C.R.; Smits, M.C.J.

2001-01-01

To improve the slip resistance of solid floors in dairy cow houses and to achieve the ammonia emission reduction prescribed by the Dutch government, precast concrete floors with grooves and a dung scraper were investigated. The grooves parallel to the alley had 160 mm center-to-center spacing and

Land surface cleanup of plutonium at the Nevada Test Site

International Nuclear Information System (INIS)

Ebeling, L.L.; Evans, R.B.; Walsh, E.J.

1991-01-01

The Nevada Test Site (NTS) covers approximately 3300 km 2 of high desert and is located approximately 100 km northwest of Las Vegas, Nevada. Soil contaminated by plutonium exists on the NTS and surrounding areas from safety tests conducted in the 1950s and 1960s. About 150 curies of contamination have been measured over 1200 hectares of land surface. Most contamination is found in the top 5 cm of soil but may be found as deep as 25 cm. The cost of conventional removal and disposal of the full soil volume has been estimated at over $500,000,000. This study is directed toward minimizing the volume of waste which must be further processed and disposed of by precisely controlling soil removal depth. The following soil removal machines were demonstrated at the NTS: (1) a CMI Corporation Model PR-500FL pavement profiler, (2) a CMI Corporation Model TR-225B trimmer reclaimer, (3) a Caterpillar Model 623 elevating scraper equipped with laser depth control, (4) a Caterpillar Model 14G motor grader equipped with laser depth control, (5) a Caterpillar Model 637 auger scraper, and (6) a XCR Series Guzzler vacuum truck. The most effective removal technique tested was the pavement profiler, which provided for dust control and precisely removed thin layers of soil. Soil removal with the motor grader and paddle scraper generated unacceptable dust levels, even after the soil was extensively watered. The vacuum truck was ineffective because of its limited intake volume which is a function of its small intake size, its weak intake force, and the tendency of its filters to clog

Evaluative Testing of the Bent Canyon Stage Station on the Pinon Canyon Maneuver Site, Las Animas County, Colorado

Science.gov (United States)

2005-01-01

Spanish maps of New Mexico, such as the "Jornada del Muerto" and the "Llanos sin Agua " (Miera y Pacheco 1778). Accommodations to these limitations also... reused for purposes other than those intended by the manufacturer, for example, bottle glass worked into scrapers. Data entered in artifact tables

MINIMARS conceptual design: Final report

International Nuclear Information System (INIS)

Lee, J.D.

1986-09-01

This volume contains the following sections: (1) fueling systems; (2) blanket; (3) alternative blanket concepts; (4) halo scraper/direct converter system study and final conceptual design; (5) heat-transport and power-conversion systems; (6) tritium systems; (7) minimars air detritiation system; (8) appropriate radiological safety design criteria; and (9) cost estimate

Development of highly heat-resistant target elements for fusion reactors; Entwicklung hochwaermebestaendiger Targetelemente fuer Fusionsreaktoren

Energy Technology Data Exchange (ETDEWEB)

Boscary, Jean; Stadler, R.; Greuner, H.; Smirnow, M.; Drescher, N.; Boeswirth, B.; Tretter, J.; Mendelevitch, B.

2016-06-15

The following topics are dealt with: Scientific and technical results for divertor components (''target elements'') of the Wendelstein 7-X facility, development of nondestructive test procedures at the cooling structures, development of an automatized procedure for the visual inspection, the ''scraper''-element. (HSI)

Prevalence of claw disorders in Dutch dairy cows exposed to several floor systems

NARCIS (Netherlands)

Somers, J.G.C.J.; Frankena, K.; Noordhuizen-Stassen, E.N.; Metz, J.H.M.

2003-01-01

Claw health was examined in an observational study on Dutch dairy farms with either a slatted floor (SL), slatted floor with manure scraper (SL-SCR), solid concrete floor (SCF), a straw yard (SY), or a zero-grazing feeding system (ZG). Hooves of cows' hind legs were examined for the presence and

77 FR 59658 - Notice of Inventory Completion: U.S. Department of the Interior, National Park Service, Walnut...

Science.gov (United States)

2012-09-28

...-worked animal bones, 6 bone artifacts, 5 rubbing/polishing stones, 4 flake tools, 4 bags of ceramic sherds, 2 ceramic sherds, 3 projectile points, 3 pendants, 2 ground stone artifacts, 2 nodules, 2 scrapers, 2 bifaces, 2 un-worked stones, 2 boxes of soil, 6 boxes of wood fragments, 1 anvil, 1 ceramic...

77 FR 25736 - Notice of Intent To Repatriate Cultural Items: Northwest Museum of Arts & Culture, Spokane, WA...

Science.gov (United States)

2012-05-01

... Register (75 FR 58424-58425, September 24, 2010), paragraph six is corrected by substituting the following... pendant, 5 scrapers, 2 bone awls, 1 piece of matting, 1 flake, 2 dentalia necklace fragments, 1 small box of dentalia beads, 1 bone needle, 1 copper pendant, 18 rolled copper beads, 6 dentalium, 1 piece of...

77 FR 25742 - Notice of Inventory Completion: Northwest Museum of Arts & Culture, Spokane, WA; Correction

Science.gov (United States)

2012-05-01

...-58430, September 24, 2010), paragraph six is corrected by substituting the following paragraph: Human... funerary objects are 1 basalt piece, 1 bone awl, 2 unworked and worked cache forms, 1 scraper, 2 pestles, 1 blade fragment, 1 piece of wood, 3 projectile points, and 1 knife. In the Federal Register (75 FR 58429...

Pack stability in dip faces fitted with scraper conveyors

Energy Technology Data Exchange (ETDEWEB)

Schwartzmann, R

1978-01-01

This paper presents an account of an investigation conducted by CERCHAR, at the request of HBNPC, into the problems of goafside pack stability. Winning method and support and stowing techniques are described. Sets out the study methods used: systematic measurement (by direct or remote means) using an instrument developed by CERCHAR to investigate all aspects of in situ pack behaviour: settling, stresses, pressure on supports, etc. Gives the results of the investigation (tables and graphs) load-bearing capacity of the supports, deformation of the surrounding rock, convergence and stresses in the pack (figures, graphs), resistance of support-timber screen, model of in situ pack behaviour. Detailed conclusions (potential techniques, detailed study, practical improvements in packing techniques) are presented.

Viscose liquid heat treatment using plate scraper heat exchanger

Directory of Open Access Journals (Sweden)

K. A. Rashkin

2012-01-01

Full Text Available The current work analyzes the use of different types of heat exchangers, depending on the technology of production. It is taken the detail analysis of the ways of applicability of various types of heat exchangers, depending on the viscosity of the processed product. It is posed the problem of the analytical determination of the required area of heat exchange with the use of differential equations of heat transfer in a moving liquid media, written in cylindrical coordinates, for symmetrical temperature distribution, without taking in account the energy dissipation.

Evaluation of Two Surface Sampling Methods for Microbiological and Chemical Analyses To Assess the Presence of Biofilms in Food Companies.

Science.gov (United States)

Maes, Sharon; Huu, Son Nguyen; Heyndrickx, Marc; Weyenberg, Stephanie van; Steenackers, Hans; Verplaetse, Alex; Vackier, Thijs; Sampers, Imca; Raes, Katleen; Reu, Koen De

2017-12-01

Biofilms are an important source of contamination in food companies, yet the composition of biofilms in practice is still mostly unknown. The chemical and microbiological characterization of surface samples taken after cleaning and disinfection is very important to distinguish free-living bacteria from the attached bacteria in biofilms. In this study, sampling methods that are potentially useful for both chemical and microbiological analyses of surface samples were evaluated. In the manufacturing facilities of eight Belgian food companies, surfaces were sampled after cleaning and disinfection using two sampling methods: the scraper-flocked swab method and the sponge stick method. Microbiological and chemical analyses were performed on these samples to evaluate the suitability of the sampling methods for the quantification of extracellular polymeric substance components and microorganisms originating from biofilms in these facilities. The scraper-flocked swab method was most suitable for chemical analyses of the samples because the material in these swabs did not interfere with determination of the chemical components. For microbiological enumerations, the sponge stick method was slightly but not significantly more effective than the scraper-flocked swab method. In all but one of the facilities, at least 20% of the sampled surfaces had more than 10 2 CFU/100 cm 2 . Proteins were found in 20% of the chemically analyzed surface samples, and carbohydrates and uronic acids were found in 15 and 8% of the samples, respectively. When chemical and microbiological results were combined, 17% of the sampled surfaces were contaminated with both microorganisms and at least one of the analyzed chemical components; thus, these surfaces were characterized as carrying biofilm. Overall, microbiological contamination in the food industry is highly variable by food sector and even within a facility at various sampling points and sampling times.

77 FR 11569 - Notice of Intent To Repatriate Cultural Items: USDA Forest Service, Coconino National Forest...

Science.gov (United States)

2012-02-27

... were either left in the ground or are not locatable at the present time. Between 1938 and 1940, eight..., one ceramic ladle, one stone scraper, one stone pendant and one bone tool. Based on the ceramic... the items were removed from a burial context. The human remains were either left in the ground or are...

75 FR 36107 - Notice of Intent to Repatriate Cultural Items: U.S. Department of Defense, Army Corps of...

Science.gov (United States)

2010-06-24

... fragments, 1 marble, 1 net sinker, 8 stone pestles, 3 pipes, 1 piece of polished stone, 15 projectile points, 3 railroad spikes, 6 scrapers, 4 shell pendants, 2 stone shaft abraders, and 7 pieces of worked bone... copper screw, 1 hammerstone, 1 metal ring, 2 net sinkers, 1 ochre stained ground stone, 3 shell ornaments...

Browse Title Index

African Journals Online (AJOL)

Vol 8, No 3 (2016): Special Issue, Using wind turbines in high-rise buildings in the development of sustainable architecture (case study: Kish Island), Abstract PDF. F Asadpour, S Khastoo, M.H. Rezaeian Fard. Vol 8, No 2 (2016): Special Issue: Part 3, Using wind turbines in sky scrapers to develop the stable architecture ...

Thermal-nutritional regulation of functional groups in running water ecosystems. Technical progress report, October 1, 1978-November 1, 1980

Energy Technology Data Exchange (ETDEWEB)

Cummins, K.W.

1980-11-01

The research encompassed three general areas: (1) characterization of stream macroinvertebrate functional feeding groups (shredders, collectors, scrapers, and predators) based on morphological and behavioral adaptations and food-source-specific growth responses of selected species; (2) demonstration of the relative importance of temperature and food quality (in which maximum quality is defined as that producing the most growth) in controlling growth rate and survivorship of stream functional groups; and (3) derivation and refinement of conceptual and quantitative models of stream ecosystem structure and function, with particular emphasis on detrital processing. Verification of the functional group concept as a tool for assessing and predicting is reflected in alterations of the relative dominance of various functional groups. Food quality can strongly influence the growth rates of shredders, collectors and scrapers and override the effects of temperature in a number of cases. Gathering collectors may select food particles by size (or at least be restricted to a limited portion of the total range available) but representative species do not appear to select for quality.

Development of an optical resonator with high-efficient output coupler for the JAERI far-infrared free-electron laser

International Nuclear Information System (INIS)

Nagai, Ryoji; Hajima, Ryoichi; Nishimori, Nobuyuki; Sawamura, Masaru; Kikuzawa, Nobuhiro; Shizuma, Toshiyuki; Minehara, Eisuke

2001-01-01

An optical resonator with a high-efficient output coupler was developed for the JAERI far-infrared free-electron laser. The optical resonator is symmetrical near-concentric geometry with an insertable scraper output coupler. As a result of the development of the optical resonator, the JAERI-FEL has been successfully, lased with averaged power over 1 kW. Performance of the optical resonator with the output coupler was evaluated at optical wavelength of 22 μm by using an optical mode calculation code. The output coupling and diffractive loss with a dominant eigen-mode of the resonator were calculated using an iterative computation called Fox-Li procedure. An efficiency factor of the optical resonator was introduced for the evaluation of the optical resonator performance. The efficiency factor was derived by the amount of the output coupling and diffractive loss of the optical resonator. It was found that the optical resonator with the insertable scraper coupler was the most suitable to a high-power and high-efficient far-infrared free-electron laser. (author)

Optimal Height Of Land Development – An Economic Perspective

Directory of Open Access Journals (Sweden)

Żelazowski Konrad

2015-03-01

Full Text Available Sky-scrapers are rising in the panorama of big modern cities more and more often, becoming a symbol of dynamic growth and prestige. High-rise development appears to be an answer to the expanding demand for new residential and commercial space as urban land prices continue to go up and the availability of land decreases.

76 FR 73667 - Notice of Inventory Completion: U.S. Department of Defense, Army Corps of Engineers, Walla Walla...

Science.gov (United States)

2011-11-29

... Burial 1; and 2 lots of seed beads from Burial 29. The estimated date range of the burials from 45BN3 is... ground stone items, 43 projectile points, 1 shell pendant, 1 stone pendant, 1 stone pipe, 1 stone scraper... carved bone items, 1 incised bone item, 1 mortar, 3 pecked stone items, 2 pestles, 17 projectile points...

77 FR 15796 - Notice of Intent To Repatriate Cultural Items: U.S. Department of the Interior, Bureau of Indian...

Science.gov (United States)

2012-03-16

... stone and 1 chert scraper. The Pinnacle Site consists of a pueblo of about 10 rooms and dates from A.D... with additional stone alignments and dates from A.D. 1275-1400, based on the ceramic assemblage. The... Assessment of White Mountain Apache Tribal Lands (Fort Apache Indian Reservation),'' by John R. Welch and T.J...

Environmental Assessment: Anti-Terrorism/Force Protection McConnell Air Force Base, Kansas

Science.gov (United States)

2003-09-01

handled, stored, transported, disposed, or recycled in accordance with these regulations. The potential for hazardous waste generation from gate...Loader (rubber tire) Concrete Truck Concrete Finisher Crane Asphalt Spreader Roller Flat Bed Truck (18 wheel) Scraper Trenching Machine 1...plastics, and lumber. These materials would be placed in the appropriate construction materials landfill or recycled when possible. These wastes

Tri-Service Corrosion Conference

Science.gov (United States)

2002-01-18

Video- Thermographie. M.S. Thesis, University Magdeburg , Germany 5. N. Meyendorf et al. (2001) Early Detection of Corrosion in Aircraft Structures...We serve as a bridge between developers and users, helping transition technologies into operational use. For more information, contact: Major...scrapers, tractors, fork lifts and material trucks. • Engineer-Trlr - trailered engineering equipment including, fixed bridge , fuel pump module, water

Making Do with What We Have: Use Your Bootstraps

Science.gov (United States)

Calmettes, Guillaume; Drummond, Gordon B.; Vowler, Sarah L.

2012-01-01

A jack knife is a pocket knife that is put to many tasks, because it's ready to hand. Often there could be a better tool for the job, such as a screwdriver, a scraper, or a can-opener, but these are not usually pocket items. In statistical terms, the expression implies making do with what's available. Another simile, of an extreme situation, is…

MINIMARS conceptual design: Report I. Volume 2

International Nuclear Information System (INIS)

Lee, J.D.

1985-12-01

This report contains separate articles of seven aspects of the MINIMARS programs. The areas discussed are Fusion Engineering Design Center, Halo Model and Computer Code, safety design, the University of Wisconsin blankets, activation product transport in a FLiBe-VANADIUM alloy HT-9 system, a halo scraper/direct converter system, and heat transport power conversion. The individual articles are cataloged separately

MINIMARS conceptual design: Report I. Volume 2

Energy Technology Data Exchange (ETDEWEB)

Lee, J.D. (ed.)

1985-12-01

This report contains separate articles of seven aspects of the MINIMARS programs. The areas discussed are Fusion Engineering Design Center, Halo Model and Computer Code, safety design, the University of Wisconsin blankets, activation product transport in a FLiBe-VANADIUM alloy HT-9 system, a halo scraper/direct converter system, and heat transport power conversion. The individual articles are cataloged separately. (WRF)

Land surface cleanup of plutonium at the Nevada Test Site

International Nuclear Information System (INIS)

Ebeling, L.L.; Evans, R.B.; Walsh, E.J.

1991-01-01

The Nevada Test Site (NTS) covers approximately 3300 km 2 of high desert and is located approximately 100 km northwest of Las Vegas, Nevada. Soil contaminated by plutonium exists on the NTS and surrounding areas from safety tests conducted in the 1950s and 1960s. About 150 curies of contamination have been measured over 1200 hectares of land surface. Most contamination is found in the top 5 cm of soil but may be found deep as 25 cm. The cost of conventional removal and disposal of the full soil volume has been estimated at over $500,000,000. This study is directed toward minimizing the volume of waste which must be further processed and disposed of by precisely controlling soil removal depth. The following soil removal machines were demonstrated at the NTS: (1) a CMI Corporation Model PR-500FL pavement profiler, (2) a CMI Corporation Model Tr-225B trimmer reclaimer, (3) a Caterpillar Model 623 elevating scraper equipped with laser depth control, (4) a Caterpillar Model 14G motor grader equipped with laser depth control, (5) a Caterpillar Model 637 auger scraper, and (6) a XCR Series Guzzler vacuum truck. 5 refs., 5 figs

Liquid wastes concentrating and solidifying device

International Nuclear Information System (INIS)

Kamiyoshi, Hideki; Ninokata, Yoshihide.

1985-01-01

Purpose: To provide a device for concentrating to solidify radioactive liquid wastes at large solidifying speed and with high decontaminating coefficient, without requirement for automatic control. Constitution: An asphalt solidifying device is disposed below a centrifugal thin film drier, and powder resulted from the drier is directly solidified with asphalt by utilizing the rotation of the drier for the mixing operation in the asphalt vessel. If abnormality should occur in the operation of the drier, resulting liquid wastes can be received and solidified in the asphalt vessel. The liquid wastes are heated to dry in a vessel main body having the heating surface at the circumferential surface. The vessel main body provided with a nozzle for supplying liquid to be treated disposed slantwise at the upper portion of the heating face, scrapers which rotate and slidingly contact the heating face and nozzles which jet out chemicals to the heating face behind the scrapers. Below the vessel main body, are disposed a funnel-like hopper for receiving falling scales, rotary vanes, and the likes by which the scales are introduced into the asphalt solidifying vessel. (Moriyama, K.)

Using wind turbines in sky scrapers to develop the stable ...

African Journals Online (AJOL)

The daily increasing and irregular consumption of fossil fuels as the limited energy source and its destructive effect on the environment has attracted all people attention to use the renewable energies and in this extend, application of renewable energies like wind is one of the frequent options in all around the world in order ...

Collimation systems in the next linear collider

International Nuclear Information System (INIS)

Merminga, N.; Irwin, J.; Helm, R.; Ruth, R.D.

1991-02-01

Experience indicates that beam collimation will be an essential element of the next generation e + E - linear colliders. A proposal for using nonlinear lenses to drive beam tails to large amplitudes was presented in a previous paper. Here we study the optimization of such systems including effects of wakefields and optical aberrations. Protection and design of the scrapers in these systems are discussed. 9 refs., 7 figs

Ecological assessment of the Tajan river using feeding groups of benthic macroinvertebrates and biotic indices

Directory of Open Access Journals (Sweden)

M Sharifinia

2012-06-01

Full Text Available One of the best practical methods to understand ecological status of a water body and determine impacts of human intervention in reducing water quality is using benthic macroinvertebrates as assessment tools for monitoring their biological integrity and health. The Tajan River is one of the rivers of Caspian Southernsub-basin that drains the Caspian Sea. Macroinvertebrate samples were taken using Surber’s sampler (40 x 40 cm and 100µ mesh size in 45 day intervals with 3 replicates in each sampling site for a period of one year (May 2010 to May 2011. The collected organisms were preserved in 4% formalin solution and transferred to the laboratory for identification and counting. Six different functional feeding groups of macroinvertebrate e.g. Collector-gathering, Collector-filtering, Predator, Collector-gathering /Scraper, Predator/Collector-gathering and Scraper were determined. Feeding groups of Collector-gathering, Collector-filtering and Collector-gathering /Scraper were relatively dominant in comparison to other groups. Groups of Collector-filtering and Collector-gathering were dominant in slightly and heavily polluted stations, respectively. In this study population structure measures including abundance, EPT percent and the EPT and EPT/CHIR indics were mearsured. Species diversity, species richness were also determined using Shannon- Weiner, Margalef and Jacardindics. The minimum and maximum values of Hilsenhoff biotic index were observedin stations 1 (4.29 and 5 (5.57, respectively. Moreover, the highest and lowest values of BMWP/ASPT were observed in station 1 (4.51 and 5 (3.25, respectively. Evaluation of indicators revealed less water quality at stations 2, 3 and 5 which located at the lowermost of fish farms and effluent of factory. This reduction might be implicated to the effluents of water damps from fish farms running into the stream as diversity and total abundance (% of sociable macroinvertebrates decreased and that of

Longitudinal and seasonal changes in functional organization of macroinvertebrate communities in four Oregon streams.

OpenAIRE

Hawkins, C. P.; Sedell, J. R.

1981-01-01

Relative numerical dominance and densities of invertebrate functional feeding groups are compared with longitudinal and seasonal changes in food resources in a Cascade Range stream system in Oregon. We also compare our data with hypothetical predictions of the River Continuum model. We found that both relative abundances and densities of functional groups fit qualitative characterization of stream reaches and the River Continuum model: Shredders dominated upper shaded reaches; scrapers were m...

MINIMARS interim report appendix halo model and computer code

International Nuclear Information System (INIS)

Santarius, J.F.; Barr, W.L.; Deng, B.Q.; Emmert, G.A.

1985-01-01

A tenuous, cool plasma called the halo shields the core plasma in a tandem mirror from neutral gas and impurities. The neutral particles are ionized and then pumped by the halo to the end tanks of the device, since flow of plasma along field lines is much faster than radial flow. Plasma reaching the end tank walls recombines, and the resulting neutral gas is vacuum pumped. The basic geometry of the MINIMARS halo is shown. For halo modeling purposes, the core plasma and cold gas regions may be treated as single radial zones leading to halo source and sink terms. The halo itself is differential into two major radial zones: halo scraper and halo dump. The halo scraper zone is defined by the radial distance required for the ion end plugging potential to drop to the central cell value, and thus have no effect on axial confinement; this distance is typically a sloshing plug ion Larmor diameter. The outer edge of the halo dump zone is defined by the last central cell flux tube to pass through the choke coil. This appendix will summarize the halo model that has been developed for MINIMARS and the methodology used in implementing that model as a computer code

Complementary methods of transverse emittance measurement

Energy Technology Data Exchange (ETDEWEB)

Zagel, James; Hu, Martin; Jansson, Andreas; Thurman-Keup, Randy; Yan, Ming-Jen; /Fermilab

2008-05-01

Several complementary transverse emittance monitors have been developed and used at the Fermilab accelerator complex. These include Ionization profile Monitors (IPM), Flying Wires, Schottky detectors and a Synchrotron Light Monitor (Synchlite). Mechanical scrapers have also been used for calibration purposes. This paper describes the various measurement devices by examining their basic features, calibration requirements, systematic uncertainties, and applications to collider operation. A comparison of results from different kinds of measurements is also presented.

Heat treatment regularity for viscose products in plate scrapers heat exchanger

Directory of Open Access Journals (Sweden)

K. A. Rashkin

2012-01-01

Full Text Available The current work describesthe construction of scraperplate-typeheat exchangerscurrently usedin industryand thetraffic patternof the productin it. Ananalytical model is represented and it is also posed the problemofthe analyticaldetermination ofthe requiredarea of heat exchangewith the use ofdifferential equations ofheat transfer in amovingliquid media, written in cylindrical coordinates, for symmetrical temperature distribution,without taking into accountthe energy dissipation.

Photodynamic therapy as a novel treatment for halitosis in adolescents: study protocol for a randomized controlled trial.

Science.gov (United States)

Lopes, Rubia Garcia; de Godoy, Camila Haddad Leal; Deana, Alessandro Melo; de Santi, Maria Eugenia Simões Onofre; Prates, Renato Araujo; França, Cristiane Miranda; Fernandes, Kristianne Porta Santos; Mesquita-Ferrari, Raquel Agnelli; Bussadori, Sandra Kalil

2014-11-14

Halitosis is a common problem that affects a large portion of the population worldwide. The origin of this condition is oral in 90% and systemic in 10% of cases. The unpleasant odor is mainly the result of volatile sulfur compounds produced by Gram-negative bacteria. However, it has recently been found that anaerobic Gram-positive bacteria also produce hydrogen sulfide (H2S) in the presence of amino acids, such as cysteine. Light, both with and without the use of chemical agents, has been used to induce therapeutic and antimicrobial effects. In photodynamic therapy, the antimicrobial effect is confined to areas covered by photosensitizing dye. The aim of the present study is to evaluate the antimicrobial effect of photodynamic therapy on halitosis in adolescents through the analysis of volatile sulfur compounds measured using gas chromatography and microbiological analysis of coated tongue. A quantitative clinical trial will be carried out involving 60 adolescents randomly divided into the following groups: group 1 will receive treatment with a tongue scraper, group 2 will receive photodynamic therapy applied to the posterior two-thirds of the dorsum of the tongue, and group 3 will receive combined treatment (tongue scraper and photodynamic therapy). Gas chromatography (OralChromaTM) and microbiological analysis will be used for the diagnosis of halitosis at the beginning of the study. Post-treatment evaluations will be conducted at one hour and 24 hours after treatment. The statistical analysis will include the Shapiro-Wilk test for the determination of the distribution of the data. If normal distribution is demonstrated, analysis of variance followed by Tukey's test will be used to compare groups. The Kruskal-Wallis test followed by the Student-Newman-Keuls test will be used for data with non-normal distribution. Either the paired t-test or the Wilcoxon test will be used to compare data before and after treatment, depending on the distribution of the data. The

Equipment for extracting and conveying stratified minerals

Energy Technology Data Exchange (ETDEWEB)

Blumenthal, G.; Kunzer, H.; Plaga, K.

1991-08-14

This invention relates to equipment for extracting stratified minerals and conveying the said minerals along the working face, comprising a trough shaped conveyor run assembled from lengths, a troughed extraction run in lengths matching the lengths of conveyor troughing, which is linked to the top edge of the working face side of the conveyor troughing with freedom to swivel vertically, and a positively guided chain carrying extraction tools and scrapers along the conveyor and extraction runs.

Application of radioisotopes in oil, gas and petrochemical industries

International Nuclear Information System (INIS)

Castagnet, A.C.G.

1976-01-01

The fundaments and the methodology of the principal radioisotope techniques used in the construction and operation of oil-pipes are described. These techniques deal with gamma radiography of weids, scraper tracking, leak localization in underground pipes and interface detection. The practical use of the mathematical formulas deduced during the theoretical treatment of each method is illustrated through several examples of application. A proceeding for the design of an interface detector based on gamma ray attenuation is presented [pt

St. Louis Harbor Project Pedestrian Survey, Madison County, Illinois. St. Louis District Cultural Resource Management Reports Number 24

Science.gov (United States)

1985-07-01

Britain, after 1860 (Kovel 1953:169). 3 Porcel al n 2 wheel s or casters ; one is ungl azed and very fragmented. The other is a complete wheel glazed on...piece-plotted with a transit. Following this, heavy equipment-- preferably a paddle- wheel scraper -- should remove the plow zone from the site areas...continue Into the Mississippian period (Vogel 1975). The succeeding Merrell phase Is recognized by modifications on theLateBluff jar rim and the gradual

Effectiveness of three different oral hygiene techniques on Viridans streptococci: A randomized controlled trial

Directory of Open Access Journals (Sweden)

N Naveen

2016-01-01

Full Text Available Introduction: Tongue cleaning is an important aspect of oral hygiene maintenance along with other mechanical and chemical aids. These methods have an influence on microorganism count in saliva. Aim: To assess the effectiveness of three different oral hygiene techniques on Viridans streptococci. Materials and Methods: This was a randomized controlled trial with 45 study subjects aged between 14 and 16 years and were randomly allocated into three groups: Group A - plastic tongue scraper, Group B - chlorhexidine mouthwash along with plastic tongue scraper, and Group C - chlorhexidine mouthwash. Unstimulated salivary samples were collected on the 1st, 7th, and 15th day before routine oral hygiene practices. Saliva samples were collected and incubated for 48 h on itis Salivarius(MS agar. Streptococcus mitis, Streptococcus mutans, and Streptococcus salivarius were counted. Data were analyzed using descriptive and inferential statistics. Results: The mean count of S. mitis, S. mutans, and S. salivarius for Group A, B, and C was found to be significant (P < 0.001 when compared between 1st, 7th, and 15th day. Between-groups comparisons revealed a significant difference between Groups A and C, B and C (P < 0.001. Conclusion: There was a significant reduction in bacterial count in all the participants indicating that all the three methods are useful in improving oral hygiene. Combination technique was found to be most effective.

Process of distilling, heating, and condensing bituminous shales, etc

Energy Technology Data Exchange (ETDEWEB)

Bayle, M

1892-04-26

The distillation apparatus is composed of a vertical cylinder, whose walls are formed of metal, cast iron, sheet iron, cast or welded steel, refractory clay or other convenient material. The cylinder is fixed. Along its axis passes a shaft, receiving a rotary motion from an endless screw, engaging with a helicoidal toothed wheel. The shaft carries a series of plates, moving with it, over which circulates successively the mineral, pushed from one plate to a lower one by a small scraper.

Beam Scraping to detect and remove Halo in LHC Injection

CERN Document Server

Letnes, P A; Brielmann, A; Burkhardt, H; Kramer, Daniel

2008-01-01

Fast scrapers are installed in the SPS to detect and remove beam halo before extraction of beams to the LHC, to minimize the probability for quenching of superconducting magnets in the LHC. We shortly describe the current system and then focus on our recent work, which aims at providing a system which can be used as operational tool for standard LHC injection. A new control application was written and tested with the beam. We describe the current status and results and compare these with detailed simulations.

Defining the Role of BTLA in Breast Cancer Immunosurveillance and Selective Targeting of the BTLA-HVEM-LIGHT Costimulatory System

Science.gov (United States)

2011-05-01

After confirmation by sequencing, constructs were extracted using a maxi prep kit from Sigma Aldrich. In order to determine if the wildtype and...once in 0.05% saponin and stained with anti­cytokine antibodies (anti­IL­17 FITC, IL­2 PE, IFN­ PE­Cy7, and IL­4 APC) in 0.5% saponin . All flow... Technology ) followed by 1 mg/mL collagenase D (Roche). Cells were harvested using cell scrapers and passed through 100-µm strainers prior to staining and

From the skyscraper to the ground-scraper. Rem Koolhaas’s Japanese Kasbah

OpenAIRE

Álvarez Arce, Raquel

2016-01-01

Rem Koolhaas, as a contemporary architect, draws from the proposals which were devel-oped by the architects who reacted to the ideas formulated on the International Congresses of Modern Architecture, like the Team 10 members. Woods, along with Candilis and Josic, worked out a new type of building that he called ground-scrapper, although it is better known by the name given by Alison Smithson: the mat-building. Rem Koolhaas, in the Nexus World building in Fukuoka, propose, as he says in S,M,L,...

Characteristics of Far Transported Laser Beam

Energy Technology Data Exchange (ETDEWEB)

Park, Dae Yoon; Kim, Ki Sik; Lee, Seung Gol [Inha University, Inchon (Korea, Republic of)

1997-07-01

A beam propagating in free space or in a medium generally experiences diffraction, and hence it suffers an energy loss and an wavefront distortion. It Is essential for a stable and precise communication to eliminate or to minimize the diffraction effect accompanying on propagation. The diffraction-free beam is introduced for that purpose. A typical diffraction-free beam is the Bessel beam. The Bessel beam has, however, an infinite energy in the cross-section perpendicular to the direction of propagation and, because of this fact, its realizability is sceptical. To remedy this problem, a new beam is introduced, which has a series from with a Gaussian envelope function and tested for diffraction on propagation by a computer simulation. Compared with the Bessel-Gauss beam, this new beam shows much less diffraction. While, by using a scraper mirror in an Nd:YAG laser with a ring resonator, an annular output beam is obtained. This annular beam is focused by a Fourier Transformation lens to produce a diffraction-free beam. This diffraction-free beam dose not show any noticible diffraction on propagation over the distance of 16 m, which is determined by the scraper mirror and the Fourier transformation lens. This achievement provides a profound basis for the generation of diffraction-free beams over much longer distances. The developed technique will provide a stable and precise communication method in remote controlling system, remote sensing through atmosphere, and information transfer using the optical fiber. 30 refs., 22 figs. (author)

Treatment of waste water containing solid particles (coal-ash-water suspensions) from 500 MW blocks of brown coal power plants

Energy Technology Data Exchange (ETDEWEB)

Morgenstern, H

1981-01-01

This paper presents a technological scheme and details on efficiency of the waste water cleaning installation in the 4 x 500 MW Boxberg III brown coal power plant. The power plant waste water contains between 0.1 and 100 kg of solids per m/sup 3/ of waste water; it requires cleaning to the environmental standard of up to 30 mg/l. The water cleaning installation consists of a coarse grain settling tank 30.7 m long, four one chamber thickeners with a 22 m diameter each, using aluminium sulfate as flocculent, and a water purification basin. The coarse grain settling tank is furnished with a continuously working chain scraper for removal of up to 100 m/sup 3//d of sludge from the bottom of the tank. Technological parameters of the settling tank are provided. Details of the tank's water cleaning performance are compared to the coarse grain settling tank at the Hagenwerder power plant. A list of the percentage of grain sizes removed from waste waters at both power plants is given. It is concluded that 85% of solids are removed from the Boxberg III waste water at the first water purification stage with a coarse grain settling tank and that use of continuously working chain scrapers is successful for removal of sludge with high water content and with a high content of fines in the grain size below 0.1 mm.

Bottom ash handling: why the outlook is dry

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-03-15

The author believes that dry systems are the way forward for bottom ash handling at coal fired power plants. The first two commercial installations of Clyde Bergemann's DRYCON system, in China, are due to enter operation shortly. The DRY ash CONveyor (DRYCON) employs fresh air flow to cool the ash, returning reheat energy to the boiler. It also addresses some problems encountered with previous dry technologies whilst increasing ash capacity and enhancing ash cooking. The advantages of the DRYCON over the wet submerged scraper conveyor are listed. 7 figs.

Retort

Energy Technology Data Exchange (ETDEWEB)

Schultz, E L

1928-11-22

A retort is described for gasifying coal, shale, lignite, and other organic substances, wherein the material is supplied from a hopper, as a film past a centrally heated chamber by means of a tier of overlapping rings provided with a spiral or screw edging. The rings are attached to an outer shell to which is given a rotary and a reciprocatory motion. The gas outlets are provided with open liquid seals and the spent material is delivered to a rotary water trough from whence it is removed by means of a scraper baffle.

National Guard and Reserve Equipment Report for Fiscal Year 2012 (NGRER FY 2012)

Science.gov (United States)

2011-02-01

to be 97 percent filled; however, only 61 percent will be modernized.  HTV fleet is projected to be 100 percent filled; however, the 20-ton Dump ...185 91 49% $29.3M High Mobility Engineer Excavator 64 35 55% $7.3M Hydraulic Excavator (HYEX) 133 78 59% $19.5M Scrapers 410 364 89% $32.9M...A46758 $800,000 11 11 11 11 11 Aviation Radio Set, HF, AN/VRC-100(V)1 R81691 $33,707 173 173 173 173 238 Hoist , High Performance H39331 $142,338 221

National Guard and Reserve Equipment Report for Fiscal Year 2013 (NGRER FY 2013)

Science.gov (United States)

2012-02-01

Trucks and 83 percent of its Semitrailer Tankers. The Army Reserve has highlighted shortfalls in the modernization of its 5-ton Dump Trucks and Heavy...C61597 $3,000,000 20 21 21 21 22 Hoist High Performance: H39331 $142,338 217 230 230 230 431 Power Unit Aux: Aviation Multi-Output GTED (AGPU) P44627...324,218 130 130 130 130 92 Scraper Earth Moving: SP 14-18 cu yd (CCE) S56246 $149,523 369 384 398 436 402 Excavator: Hydraulic (HYEX) Type I E27792

Shielding plug for LMFBR type reactors

International Nuclear Information System (INIS)

Hashiguchi, Ko.

1979-01-01

Purpose: To enable effective removal of liquid metals deposited, if any, in the gaps between a rotary plug and a fixed plug in LMFBR type reactors. Constitution: A plate incorporated with a heater and capable of projecting in a gap between a rotary plug and a fixed plug, and a scraper connected in perpendicular to it are provided to the rotary plug. Solidified liquid metals such as sodium deposited in the gap are effectively removed by the heating with the heater and the scraping action due to the rotation. (Horiuchi, T.)

Cavity and goaf control

Energy Technology Data Exchange (ETDEWEB)

Stassen, P

1978-01-01

A summary of stowing, including a definition, calculation of stowing material requirements and settling of packs is given. A) Stowing using dirt found locally - the dirt bands in the seam - the use of ripping dirt brought down by the scraper loader and used for packing purposes and the construction of dummy roads. B) Control of cavities by leaving short, thick props and timber chocks in place. C) Stowing methods involving imported firt: packing by hand, use of scraper loaders, slinger stowing and control led-gravity stowing. D) Pneumatic stowing: describes the various types of machine and their scope; pipelines, their installation and cost price; pneumatic stowing in conjunc tion with powered supports; the use of crusher-stowers for stowing ripping dirt; construction of anhydrite packs by means of a pneumatic stower. E) Hydraulic stowing: how it works, the materials involved, utilization conditions, the surface storage post, pipes, stoppings with stowed material, water removal, rates of hydraulic stowing, results of theoretical studies, and the use of hydraulic stowing in the metal-mines. F) Pumped packs: how they work, how the packs are installed, the strength of the packs and their various uses. G) Caving: describes the principle of caving, support patterns, caving with packs and makes a comparison between caving and stowing. H) Comparison between the various methods of stowing compares pneumatic with hydraulic stowing methods; compares packing by hand and mechanical stowing compares surface subsidence in terms of the method of goaf used underground. An appendix gives details of equipment used. (15 refs.) (In French)

AUTOMATED CONTROL AND REAL-TIME DATA PROCESSING OF WIRE SCANNER/HALO SCRAPER MEASUREMENTS

International Nuclear Information System (INIS)

Day, L.A.; Gilpatrick, J.D.

2001-01-01

The Low-Energy Demonstration Accelerator (LEDA), assembled and operating at Los Alamos National Laboratory, provides the platform for obtaining measurements of high-power proton beam-halo formation. Control system software and hardware have been integrated and customized to enable the production of real-time beam-halo profiles. The Experimental Physics and Industrial Control System (EPICS) hosted on a VXI platform, Interactive Data Language (IDL) programs hosted on UNIX platforms, and LabVIEW (LV) Virtual Instruments hosted on a PC platform have been integrated and customized to provide real-time, synchronous motor control, data acquisition, and data analysis of data acquired through specialized DSP instrumentation. These modules communicate through EPICS Channel Access (CA) communication protocol extensions to control and manage execution flow ensuring synchronous data acquisition and real-time processing of measurement data. This paper describes the software integration and management scheme implemented to produce these real-time beam profiles

Experimental investigations of the stability of winning equipment and of scraper-chain conveyors

Energy Technology Data Exchange (ETDEWEB)

Henkel, E H [Bergbau-Forschung G.m.b.H., Essen (Germany, F.R.). Versuchsfeld fuer Gewinnungs- und Strebfoerdertechnik; Ahrens, K; Dembeck, R [Berbau-Forschung G.m.b.H., Essen (Germany, F.R.)

1979-06-01

Extensive experiments have been carried out in order to find out about the correlation between strength and time behaviour of displacement, holding, and staying forces. The findings have shown that displacement forces depend on chain slack forces due to the drives. The maximum values of slack forces do not occur together, so that their sum does not act as total force. One finding was that when overload prevention devices are used, these do not respond simultaneously. Therefore, only the shear bolt fracture force of one drive can have a displaying effect. Apart from frictional forces, position-stabilizing holding forces were effects of mass acceleration and elastic forces as well as the holding forces of the longwall face. In addition to these experiments, a mathematical description of blocking and staying processes was elaborated at the institute of mining scineces of Aachen technical university.

Training manual for precision hand deburring, Part 3

Energy Technology Data Exchange (ETDEWEB)

Gillespie, L.K.

1981-03-01

This publication is Part 3 of a 4 part training manual to be used by machinist trainees, production workers, and others removing burrs from precision miniature parts. The manuals are written to be self-teaching and are intended to be used with two hours of training each day along with six additional hours of bench work in deburring. This part describes mounted stones, scrapers, hand stones, abrasive filled rubber and cotton tools, abrasive paper products, felt bobs and lapping compounds, mandrels and arbors, miscellaneous tools, personal techniques for assuring quality, cleaning parts, and deburring gears and plastic parts.

Carbonizing etc. , coal etc

Energy Technology Data Exchange (ETDEWEB)

Duckham, A M; Rider, D; Watts, J S

1924-01-17

In drying, carbonizing, and distilling coal, shale, etc., by passage through a heated retort, the material is spread in a thin layer over the heating surface by a conveying-screw with a shallow thread. The retort is heated by a bath of molten metal, and the conveyingscrew intermeshes with a scraper screw of smaller diameter, and of a different hand; the screws are mounted on shafts geared together by wheels. The material after passing through the retort is delivered into a chute closed at the bottom by an arc-shaped water seal carried on arms and opened periodically by a lever.

Instant web scraping with Java

CERN Document Server

Mitchell, Ryan

2013-01-01

This book is full of short, concise recipes to learn a variety of useful web scraping techniques using Java. You will start with a simple basic recipe of setting up your Java environment and gradually learn some more advanced recipes such as using complex Scrapers.Instant Web Scraping with Java is aimed at developers who, while not necessarily familiar with Java, are at least ready to dive into the complexities of this language with simple, step-by-step instructions leading the way. It is assumed that you have at least an intermediate knowledge of HTML, some knowledge of MySQL, and access to a

Developing an Open-Source Bibliometric Ranking Website Using Google Scholar Citation Profiles for Researchers in the Field of Biomedical Informatics.

Science.gov (United States)

Sittig, Dean F; McCoy, Allison B; Wright, Adam; Lin, Jimmy

2015-01-01

We developed the Biomedical Informatics Researchers ranking website (rank.informatics-review.com) to overcome many of the limitations of previous scientific productivity ranking strategies. The website is composed of four key components that work together to create an automatically updating ranking website: (1) list of biomedical informatics researchers, (2) Google Scholar scraper, (3) display page, and (4) updater. The site has been useful to other groups in evaluating researchers, such as tenure and promotions committees in interpreting the various citation statistics reported by candidates. Creation of the Biomedical Informatics Researchers ranking website highlights the vast differences in scholarly productivity among members of the biomedical informatics research community.

Immersion piston for producing crude oil and liquids from boreholes

Energy Technology Data Exchange (ETDEWEB)

Fekete, I; Hornyos, J

1967-02-09

When using a free piston to pump an oil well, oil and gas accumulates above and below the piston; upon venting the gas pressure above the piston, the gas pressure below it drives the piston and the oil above it to the surface. In the past, such pistons were too heavy and did not run tight in the tubing, causing loss of efficiency and high gas consumption. According to this invention, the piston is made of aluminum or plastic; it consists of at least 2 parts flexibly connected by wire rope or plastic strings, and is equipped with a labyrinth gasket and a paraffin scraper. (3 claims)

Some problems in exploitation of deep-pumping wells in Tatarian oil fields

Energy Technology Data Exchange (ETDEWEB)

Ishemguzhin, S B

1970-01-01

Difficulty has been experienced in pumping paraffinic oil with rod pumps. The rods have scrapers to remove paraffin from tubing walls, however this method does not work well. In an effort to improve pumping efficiency, gas anchors of various types were tried. Best results were obtained when the pumps, equipped with gas anchors, were placed about 300 m under the dynamic liquid level, and separated gas was steadily removed through the annulus. With this arrangement, more complete filling of the pump was achieved. Experience has shown that with separate production of gas from wells, the useful stroke of the pump plunger is increased as well as productivity of deep-pumping equipment.

Keeping condensers clean

Energy Technology Data Exchange (ETDEWEB)

Wicker, K.

2006-04-15

The humble condenser is among the biggest contributors to a steam power plant's efficiency. But although a clean condenser can provide great economic benefit, a dirty one can raise plant heat rate, resulting in large losses of generation revenue and/or unnecessarily high fuel bills. Conventional methods for cleaning fouled tubes range form chemicals to scrapers to brushes and hydro-blasters. This article compares the available options and describes how one power station, Omaha Public Power District's 600 MW North Omaha coal-fired power station, cleaned up its act. The makeup and cooling water of all its five units comes from the Missouri River. 6 figs.

Assessing the functional diversity of herbivorous reef fishes using a compound-specific stable isotope approach

KAUST Repository

Tietbohl, Matthew

2016-12-01

Herbivorous coral reef fishes play an important role in helping to structure their environment directly by consuming algae and indirectly by promoting coral health and growth. These fishes are generally separated into three broad groups: browsers, grazers, and excavators/scrapers, with these groupings often thought to have a fixed general function and all fishes within a group thought to have similar ecological roles. This categorization assumes a high level of functional redundancy within herbivorous fishes. However, recent evidence questions the use of this broad classification scheme, and posits that there may actually be more resource partitioning within these functional groupings. Here, I use a compound-specific stable isotope approach (CSIA) to show there appears to be a greater diversity of functional roles than previously assumed within broad functional groups. The δ13C signatures from essential amino acids of reef end-members (coral, macroalgae, detritus, and phytoplankton) and fish muscle were analyzed to investigate differences in resource use between fishes. Most end-members displayed clear isotopic differences, and most fishes within functional groups were dissimilar in their isotopic signature, implying differences in the resources they target. No grazers closely resembled each other isotopically, implying a much lower level of functional redundancy within this group; scraping parrotfish were also distinct from excavating parrotfish and to a lesser degree distinct between scrapers. This study highlights the potential of CSIA to help distinguish fine-scale ecological differences within other groups of reef organisms as well. These results question the utility of lumping nominally herbivorous fishes into broad groups with assumed similar roles. Given the apparent functional differences between nominally herbivorous reef fishes, it is important for managers to incorporate the diversity of functional roles these fish play.

Assessing the functional diversity of herbivorous reef fishes using a compound-specific stable isotope approach

KAUST Repository

Tietbohl, Matthew

2016-01-01

Herbivorous coral reef fishes play an important role in helping to structure their environment directly by consuming algae and indirectly by promoting coral health and growth. These fishes are generally separated into three broad groups: browsers, grazers, and excavators/scrapers, with these groupings often thought to have a fixed general function and all fishes within a group thought to have similar ecological roles. This categorization assumes a high level of functional redundancy within herbivorous fishes. However, recent evidence questions the use of this broad classification scheme, and posits that there may actually be more resource partitioning within these functional groupings. Here, I use a compound-specific stable isotope approach (CSIA) to show there appears to be a greater diversity of functional roles than previously assumed within broad functional groups. The δ13C signatures from essential amino acids of reef end-members (coral, macroalgae, detritus, and phytoplankton) and fish muscle were analyzed to investigate differences in resource use between fishes. Most end-members displayed clear isotopic differences, and most fishes within functional groups were dissimilar in their isotopic signature, implying differences in the resources they target. No grazers closely resembled each other isotopically, implying a much lower level of functional redundancy within this group; scraping parrotfish were also distinct from excavating parrotfish and to a lesser degree distinct between scrapers. This study highlights the potential of CSIA to help distinguish fine-scale ecological differences within other groups of reef organisms as well. These results question the utility of lumping nominally herbivorous fishes into broad groups with assumed similar roles. Given the apparent functional differences between nominally herbivorous reef fishes, it is important for managers to incorporate the diversity of functional roles these fish play.

TPX/TFTR Neutral Beam energy absorbers

International Nuclear Information System (INIS)

Dahlgren, F.; Wright, K.; Kamperschroer, J.; Grisham, L.; Lontai, L.; Peters, C.; VonHalle, A.

1993-01-01

The present beam energy absorbing surfaces on the TFTR Neutral Beams such as Ion Dumps, Calorimeters, beam defining apertures, and scrapers, are simple water cooled copper plates which wee designed to absorb (via their thermal inertia) the incident beam power for two seconds with a five minute coal down interval between pulses. These components are not capable of absorbing the anticipated beam power loading for 1000 second TPX pulses and will have to be replaced with an actively cooled design. While several actively cooled energy absorbing designs were considered,, the hypervapotron elements currently being used on the JET beamlines were chosen due to their lower cooling water demands and reliable performance on JET

Cooled Beam Diagnostics on LEIR

CERN Document Server

Tranquille, G; Carli, C; Chanel, M; Prieto, V; Sautier, R; Tan, J

2008-01-01

Electron cooling is central in the preparation of dense bunches of lead beams for the LHC. Ion beam pulses from the LINAC3 are transformed into short highbrightness bunches using multi-turn injection, cooling and accumulation in the Low Energy Ion Ring, LEIR [1]. The cooling process must therefore be continuously monitored in order to guarantee that the lead ions have the required characteristics in terms of beam size and momentum spread. In LEIR a number of systems have been developed to perform these measurements. These include Schottky diagnostics, ionisation profile monitors and scrapers. Along with their associated acquisition and analysis software packages these instruments have proved to be invaluable for the optimisation of the electron cooler.

Sodium aerosol recovering device

International Nuclear Information System (INIS)

Fujimori, Koji; Ueda, Mitsuo; Tanaka, Kazuhisa.

1997-01-01

A main body of a recovering device is disposed in a sodium cooled reactor or a sodium cooled test device. Air containing sodium aerosol is sucked into the main body of the recovering device by a recycling fan and introduced to a multi-staged metal mesh filter portion. The air about against each of the metal mesh filters, and the sodium aerosol in the air is collected. The air having a reduced sodium aerosol concentration circulates passing through a recycling fan and pipelines to form a circulation air streams. Sodium aerosol deposited on each of the metal mesh filters is scraped off periodically by a scraper driving device to prevent clogging of each of the metal filters. (I.N.)

Electron cooling experiments at the ESR

International Nuclear Information System (INIS)

Steck, M.; Beller, P.; Beckert, K.; Franzke, B.; Nolden, F.

2004-01-01

The properties of electron cooled beams of highly charged ions have been studied at the ESR. New experiments using a beam scraper to determine the transverse beam size provide the beam parameters in the intrabeam scattering dominated intensity regime, but also at very low intensity when the ion beam enters into an ultra-cold state. Extremely low values of longitudinal and transverse beam temperature on the order of meV were achieved for less than 1000 stored ions. An experiment with bunched ultra-cold beam showed a limit of the line density which agrees with the one observed for coasting beams. Cooling of decelerated ions at a minimum energy of 3 MeV/u has been demonstrated recently

Small-gap undulator experiment on the NSLS X-ray Ring

International Nuclear Information System (INIS)

Stefan, P.M.; Krinsky, S.; Rakowsky, G.; Solomon, L.

1995-01-01

We report results of an on-going experiment being carried out in the X13 straight section of the NSLS X-ray Ring which explores the limits of the operation of small-gap undulators. In particular, we discuss measurements of stored electron beam lifetime as a function of the vertical aperture presented by a 4-jaw scraper or a variable-aperture vacuum vessel. At an electron beam current of 300 mA the variable-aperture vacuum chamber was closed to an inner aperture of 3.8 mm with no effect on the electron beam lifetime. Measurements of the output radiation spectrum of a 16 mm period undulator at a magnet gap of 7.5 mm are also described

29 CFR 1926.1001 - Minimum performance criteria for rollover protective structures for designated scrapers, loaders...

Science.gov (United States)

2010-07-01

... loaders, and motor graders. The vehicle and ROPS as a system shall have the structural characteristics... direction of the load application, measured at the ROPS top edge. Should the operator's seat be offcenter... Society of Automotive Engineers Recommended Practices: SAE J320a, Minimum Performance Criteria for Roll...

Shale retort

Energy Technology Data Exchange (ETDEWEB)

Overton, P C

1936-07-22

A vertical distillation retort with an enclosed annular heating chamber has enclosed therein tiered compartments spaced apart by chambers into which burners deliver heating gases which pass via ports to the chamber and thence to the atmosphere. Shale is delivered by means of an air tight chute to the uppermost compartment and is spread therein and passed downwardly from compartment to compartment through ports, finally passing from the retort through an airtight chute, by means of scrapers rotatably mounted on a hollow shaft through which noncondensible gases are delivered to the distilling material via jets. The gaseous products of distillation are educted through ports and a manifold, which is also in communication with the head of the retort through the delivery pipe.

Continuous denitration device by microwave heating

International Nuclear Information System (INIS)

Matsumaru, Ken-ichi; Sato, Hajime.

1982-01-01

Purpose: To continuously obtain powder of uranium dioxide, plutonium dioxide or a mixture of them respectively from the solution of uranyl nitrate, plutonium nitrate or a mixture of them effectively while maintaining a constant quality. Constitution: Plutonium nitrate or uranium nitrate solution is deposited on a rotational drum having a heater and dried into powderous products. The powderous products are scraped off by a blade, transferred to a belt conveyor, entered into a microwave heating furnace and heated by microwaves while stirring to obtain the powder of plutonium dioxide or uranium dioxide. The powderous products are scraped off by a scraper and collected in a receiving tank for denitration products, whereby the feeding solution can be denitrated continuously. (Horiuchi, T.)

Invasive alien species water hyacinth Eichhornia crassipes as abode for macroinvertebrates in hypertrophic Ramsar Site, Lake Xochimilco, Mexico.

Science.gov (United States)

Rocha-Ramirez, A; Robles-Valderrama, E; Ramirez-Flores, E

2014-11-01

This paper presents information on the density, diversity and functional feeding groups of macroinvertebrate assemblages associated with water hyacinth in Antiguo Canal Cuemanco, part of Lake Xochimilco in Mexico City. Rare (low frequency and density) and dominant (high frequency and density) taxa prevailed in the assemblages, with the most predominant being Hyalella azteca, Chironomus plumosus and Ischnura denticollis. Nonmetric Multidimensional Scaling confirmed two climatic seasons: warm-rainy and cold-dry; the former with the highest diversity and density of taxa. Canonical Correspondence Analysis showed that conductivity, nitrates and turbidity explained the density variations of taxa. Antiguo Canal Cuemanco waters are spatially homogeneous with the characteristics of hypertrophic shallow lakes, inhabited by scrapers and gathering-collectors. The species found were tolerant to organic pollution.

A mechanistic model for electricity consumption on dairy farms: definition, validation, and demonstration.

Science.gov (United States)

Upton, J; Murphy, M; Shalloo, L; Groot Koerkamp, P W G; De Boer, I J M

2014-01-01

Our objective was to define and demonstrate a mechanistic model that enables dairy farmers to explore the impact of a technical or managerial innovation on electricity consumption, associated CO2 emissions, and electricity costs. We, therefore, (1) defined a model for electricity consumption on dairy farms (MECD) capable of simulating total electricity consumption along with related CO2 emissions and electricity costs on dairy farms on a monthly basis; (2) validated the MECD using empirical data of 1yr on commercial spring calving, grass-based dairy farms with 45, 88, and 195 milking cows; and (3) demonstrated the functionality of the model by applying 2 electricity tariffs to the electricity consumption data and examining the effect on total dairy farm electricity costs. The MECD was developed using a mechanistic modeling approach and required the key inputs of milk production, cow number, and details relating to the milk-cooling system, milking machine system, water-heating system, lighting systems, water pump systems, and the winter housing facilities as well as details relating to the management of the farm (e.g., season of calving). Model validation showed an overall relative prediction error (RPE) of less than 10% for total electricity consumption. More than 87% of the mean square prediction error of total electricity consumption was accounted for by random variation. The RPE values of the milk-cooling systems, water-heating systems, and milking machine systems were less than 20%. The RPE values for automatic scraper systems, lighting systems, and water pump systems varied from 18 to 113%, indicating a poor prediction for these metrics. However, automatic scrapers, lighting, and water pumps made up only 14% of total electricity consumption across all farms, reducing the overall impact of these poor predictions. Demonstration of the model showed that total farm electricity costs increased by between 29 and 38% by moving from a day and night tariff to a flat

On the estimation of the wake potential for an ultrarelativistic charge in an accelerating structure

International Nuclear Information System (INIS)

Novokhatskij, A.V.

1988-01-01

The method to derive the analytic estimations for wake fields of an ultrarelativistic charge in an accelerating structure, that are valid in the range of distances smalller or compared to the effective structure dimensions. The method is based on the approximate space-time domain integrating of the maxwell equations in the Kirchhoff formulation. the method is demonstrated on the examples of obtaining the wake potentials for energy loss of a bunch traversing a scraper, a cavity or periodic iris-loaded structure. Likewise formulae are derived for Green functions that describe transverse force action of wake fields. Simple formulae for the total energy loss evaluation of a bunch with the Gaussian charge density distribution are derived as well. The derived estimations are compared with the computer results and predictions of other models

Advanced Light Source beam diagnostics systems

International Nuclear Information System (INIS)

Hinkson, J.

1993-10-01

The Advanced Light Source (ALS), a third-generation synchrotron light source, has been recently commissioned. Beam diagnostics were very important to the success of the operation. Each diagnostic system is described in this paper along with detailed discussion of its performance. Some of the systems have been in operation for two years. Others, in the storage ring, have not yet been fully commissioned. These systems were, however, working well enough to provide the essential information needed to store beam. The devices described in this paper include wall current monitors, a beam charge monitor, a 50 ohm Faraday cup, DC current transformers, broad-hand striplines, fluorescence screens, beam collimators and scrapers, and beam position monitors. Also, the means by which waveforms are digitized and displayed in the control room is discussed

Beam Loss Simulation Studies for ALS Top-Off Operation

CERN Document Server

Nishimura, Hiroshi; Robin, David; Steier, Christoph

2005-01-01

The ALS is planning to operate with top-off injection at higher beam currents and smaller vertical beam size. As part of a radiation safety study for top-off, we carried out two kinds of tracking studies: (1) to confirm that the injected beam cannot go into users' photon beam lines, and (2) to control the location of beam dump when the storage ring RF is tripped. (1) is done by tracking electrons from a photon beam line to the injection sector inversely by including the magnetic field profiles, varying the field strength with geometric aperture limits to conclude that it is impossible. (2) is done by tracking an electron with radiation in the 6-dim space for different combinations of vertical scrapers for the realistic lattice with errors.

Riding the belt

Energy Technology Data Exchange (ETDEWEB)

Potts, A

1998-04-01

Recent developments in conveyor systems have focused on accessories rather than the belt itself. Radio frequency identification (RFID) is a technology using transponders embedded in conveyor belts and this is the latest development at the German firm Contitech. The system described in the articles developed with Moers, features transponders for cooling, controlling and monitoring conveyor belts. Other developments mentioned include a JOKI drum motor featuring a fully integrated gearbox and electric motor enclosed in a steel shell, from Interoll; a new scraper cleaning system from Hosch, new steel cord belting from Fenner, a conveying system for Schleenhain lignite opencast mine by FAM Foerdelantigen Magdeburg; new bearings from Nadella (the sales arm of Intersoll-Rand), an anti-shock belt transfer table from Rosta and new caliper disc brakes from GE Industrial.

Thermal regulation of functional groups in running water ecosystems. Progress report, 1974--1975

International Nuclear Information System (INIS)

Cummins, K.W.; Klug, M.J.

1975-01-01

Upper and lower thermal limits and temperature dependent growth were determined for a number of organisms (or populations) representing various functional groups of stream ecosystems (microconsumers, producers, and macroconsumers, shredders, collectors, scrapers, and predators). Although temperature functions as an overall control parameter, organic substrate (microconsumers) and inorganic nutrients (microconsumers and producers), light (producers) and food quality (macroconsumers) can modify thermal responses. Stream microorganisms typically grow below their thermal optima, community composition being determined by those that can manage the maximum growth at a given temperature utilizing a given organic substrate. Producers in first to third order streams are generally light limited (although nutrient availability is also important). Food quality, primarily a function of microbial biomass in the case of detritivores. can compensate for temperature dependent growth in non-predator macroinvertebrate functional groups. (U.S.)

Biaxial vent extruder

International Nuclear Information System (INIS)

Idemoto, A.; Maki, Y.; Oda, N.

1981-01-01

A biaxial vent extruder is described for processing of slurry-like waste fluids or radioactive waste fluids which have a hopper cylinger, a solidifying substance port and a solidified substance port. A plurality of vent cylinders each having a vent port are provided with a plunger type scraper. An extruding cylinder having a single opening for a main screw is connected to the assembled vent cylinders. The main screw extends to the upstream end of the extruding cylinder and a sub-screw extends to the extruding cylinder. The screws each having a full flight engaging the other and a set of rings are mounted on the screws near the respective vent port inlets. The screws are rotated in different directions and inwardly with respect to the vent ports. Rotors may be mounted on the screws to break down solid particles

Thermal loads on the TJ-II Vacuum Vessel under Neutral Beam Injection

International Nuclear Information System (INIS)

Guasp, J.; Fuentes, C.; Liniers, M.

1996-01-01

In this study a numerical analysis of power loads on the complex 3D structure of the TJ-II Vacuum Vessel, moderated with reasonable accuracy, under NBI, is done. To do this it has been necessary to modify deeply the DENSB code for power loads in order to include the TJ-II VV wall parts as targets and as beam scrapers, allowing the possibility of self-shadowing. After a short description of the primitive version of the DENSB code (paragraph 2) and of the visualisation code MOVIE(paragraph 3), the DENSB upgrading are described (paragraphs 4,5) and finally the results are presented (paragraph 6). These code modifications and the improving on the visualization tools provide more realistic load evaluations, both with and without plasma, validating former results and showing clearly the VV zones that will need new protections. (Author)

Beam Diagnostics for the BNL Energy Recovery Linac Test Facility

International Nuclear Information System (INIS)

Cameron, Peter; Ben-Zvi, Ilan; Blaskiewicz, Michael; Brennan, Michael; Connolly, Roger; Dawson, William; Degen, Chris; DellaPenna, Al; Gassner, David; Kesselman, Martin; Kewish, Jorg; Litvinenko, Vladimir; Mead, Joseph; Oerter, Brian; Russo, Tom; Vetter, Kurt; Yakimenko, Vitaly

2004-01-01

An Energy Recovery Linac (ERL) test facility is presently under construction at BNL. The goals of this test facility are first to demonstrate stable intense CW electron beam with parameters typical for the RHIC e-cooling project (and potentially for eRHIC), second to test novel elements of the ERL (high current CW photo-cathode, superconducting RF cavity with HOM dampers, and feedback systems), and finally to test lattice dependence of stability criteria. Planned diagnostics include position monitors, loss monitors, transverse profile monitors (both optical and wires), scrapers/halo monitors, a high resolution differential current monitor, phase monitors, an energy spread monitor, and a fast transverse monitor (for beam break-up studies and the energy feedback system). We discuss diagnostics challenges that are unique to this project, and present preliminary system specifications. In addition, we include a brief discussion of the timing system

Approaches to Sustainable housing in Denmark and the international inspiration

DEFF Research Database (Denmark)

Knudstrup, Mary-Ann; Hansen, Hanne Tine Ring; Brunsgaard, Camilla

years. This brings forward an increasing challenge to plan, design and build more sustainable buildings in order to be able to contribute to or reduce the use of energy for heating and cooling in new housing projects and thereby bring down the emission of CO2 when using less fossil fuel. This is crucial...... since carbon dioxide is one of the so called greenhouse gasses playing a major role in the overheating of the globe. Thus there is focus on reducing the CO2-level on a national and global level. This paper will look upon changes in interest and the different types of approaches to sustainable design...... of buildings and show examples of houses that can minimise the use of energy for heating and cooling in shape of detached houses, sky scrapers and some student's projects with high raised houses....

Local Geomorphology as a Determinant of Macrofaunal Production in a Mountain Stream.

Science.gov (United States)

Huryn, Alexander D; Wallace, J Bruce

1987-12-01

By comparing distributions of functional group production among different habitats in an Appalachian mountain stream, the influence of site-specific geomorphology upon the overall functional group composition of the animal community was demonstrated. By replicated monthly sampling, substrate particle size distributions, current velocity, standing crops of benthic organic matter, and production of macrofauna were measured in each of three principal habitats: bedrock-outcrop, riffle, and pool. Samples were taken at randomly assigned locations and the relative number of samples taken from each habitat was assumed to be proportional to the area of the habitat within the stream. These proportions were used to weight production measured in each habitat and the resulting values were summed to obtain production per unit area of average stream bed. The bedrock-outcrop habitat was characterized by high material entertainment and export as indicated by significantly higher current velocities and lower standing crops of detritus compared to the riffle and pool habitats. Pools were sites of low entertainment and high retention of organic matter as demonstrated by significantly lower current velocities and higher accumulations of detritus than other habitats. The riffle habitat was intermediate to the bedrock-outcrop and pool habitats in all parameters measured. Annual production of collector-filterers was highest in the bedrock-outcrop (ash-free dry mass 1920 mg/m 2 ), followed by riffle (278 mg/m 2 ) and pool (32 mg/m 2 ). Although constituting only 19% of the stream area, the bedrock-outcrop habitat contributed 68% of the habitat-weighted collector-filterer production. Annual production of shredders was highest in pools (2616 mg/m 2 ), followed by riffles (1657 mg/m 2 ) and bedrock-outcrop (579 mg/m 2 ). The pool habitat, constituting 23% of stream area, contributed 36% of shredder production. Annual production of scrapers was highest in the riffle habitat (905 mg/m 2

A linked land-sea modeling framework to inform ridge-to-reef management in high oceanic islands.

Directory of Open Access Journals (Sweden)

Jade M S Delevaux

Full Text Available Declining natural resources have led to a cultural renaissance across the Pacific that seeks to revive customary ridge-to-reef management approaches to protect freshwater and restore abundant coral reef fisheries. Effective ridge-to-reef management requires improved understanding of land-sea linkages and decision-support tools to simultaneously evaluate the effects of terrestrial and marine drivers on coral reefs, mediated by anthropogenic activities. Although a few applications have linked the effects of land cover to coral reefs, these are too coarse in resolution to inform watershed-scale management for Pacific Islands. To address this gap, we developed a novel linked land-sea modeling framework based on local data, which coupled groundwater and coral reef models at fine spatial resolution, to determine the effects of terrestrial drivers (groundwater and nutrients, mediated by human activities (land cover/use, and marine drivers (waves, geography, and habitat on coral reefs. We applied this framework in two 'ridge-to-reef' systems (Hā'ena and Ka'ūpūlehu subject to different natural disturbance regimes, located in the Hawaiian Archipelago. Our results indicated that coral reefs in Ka'ūpūlehu are coral-dominated with many grazers and scrapers due to low rainfall and wave power. While coral reefs in Hā'ena are dominated by crustose coralline algae with many grazers and less scrapers due to high rainfall and wave power. In general, Ka'ūpūlehu is more vulnerable to land-based nutrients and coral bleaching than Hā'ena due to high coral cover and limited dilution and mixing from low rainfall and wave power. However, the shallow and wave sheltered back-reef areas of Hā'ena, which support high coral cover and act as nursery habitat for fishes, are also vulnerable to land-based nutrients and coral bleaching. Anthropogenic sources of nutrients located upstream from these vulnerable areas are relevant locations for nutrient mitigation, such as

A recovery installation for sodium sulfates, thiosulfates and sulfides from waste water resulting from hydrogen sulfide fabrication

International Nuclear Information System (INIS)

Mazilu, Mihai; Costescu, Sanda

2002-01-01

An installation for recovery of sodium sulfate and sulfur suspensions from waste water was conceived. It consists from a preheater, vacuum evaporator and a refrigerating system with drum and scraper. This equipment concentration the solution by eliminating in the first stage the water in the vacuum evaporator. The water resulting at this stage is chemically pure and can be discharged in the sewage sludge system. The concentrated solution is then directed to the refrigerating system with drum and scrapper. Here the sodium sulfates, thiosulfates and sulfides get crystallized onto the drum surface. The resulting aqueous solution to be discharged in the sewage sludge system is previously analyzed as in case of the absent of the recovery installation, but the amount of pollutants will be much lower because sulfates, thiosulfates and sulfides were already recovered as scales from the drum. These solid scales can be used in detergent industry

Functional groups of entomofauna associated to aquatic macrophytes in Correntoso river, Rio Negro sub-region, Pantanal, Mato Grosso do Sul State, Brazil - doi: 10.4025/actascibiolsci.v34i1.7822

Directory of Open Access Journals (Sweden)

José Sabino

2011-11-01

Full Text Available This work aimed to study the structure of functional groups of entomofauna associated to aquatic macrophytes in Correntoso river, Rio Negro sub-region, Pantanal, Mato Grosso do Sul State, Brazil. Six samples were taken in different seasonal periods; ebb, dry and wet. The organisms were collected using D net (300 m mesh, sweeping five times through the roots of macrophyte banks at each sample session. Three environments were compared (open, intermediary, close using data from six collection sites, through which were analyzed absolute abundance, observed richness of families and the sampled specimens were also separated in functional groups. A total of 60 families from 12 orders of Insecta were registered, totaling 19,773 sampled insects. The largest number of families was categorized into predators functional group, with 34 families collected, followed by the collectors with 17, shredders-herbivores ten and scrapers eight.

Landscape-scale variation in hominin tool use: Evidence from the Developed Oldowan.

Science.gov (United States)

Braun, David R; Rogers, Michael J; Harris, John W K; Walker, Steven J

2008-12-01

The relationship between artifact manufacture, use, and discard in the Developed Oldowan is complex. Here we use digital-image-analysis techniques to investigate the intensity of reduction in single-platform cores of the Developed Oldowan of the Okote Member, Koobi Fora Formation. Data suggest that this method provides a more accurate measure of reduction intensity than previous applications of a unifacial-scraper model. Assemblages of single-platform cores excavated from extensive lateral exposures of the Okote Member provide insights into the relationship between raw-material availability and discard patterns. Variation in reduction intensity suggests that tools are not always discarded in patterns that would be predicted by the availability of raw material. Further, it appears that hominin transport decisions involved an assessment of the potential use-life of certain forms. Many aspects of Developed Oldowan technology conform to previously developed models of curated technologies.

Community-level response of fishes and aquatic macroinvertebrates to stream restoration in a third-order tributary of the Potomac River, USA

Science.gov (United States)

Selego, Stephen M.; Rose, Charnee L.; Merovich, George T.; Welsh, Stuart A.; Anderson, James T.

2012-01-01

Natural stream channel design principles and riparian restoration practices were applied during spring 2010 to an agriculturally impaired reach of the Cacapon River, a tributary of the Potomac River which flows into the Chesapeake Bay. Aquatic macroinvertebrates and fishes were sampled from the restoration reach, two degraded control, and two natural reference reaches prior to, concurrently with, and following restoration (2009 through 2010). Collector filterers and scrapers replaced collector gatherers as the dominant macroinvertebrate functional feeding groups in the restoration reach. Before restoration, based on indices of biotic integrity (IBI), the restoration reach fish and macroinvertebrate communities closely resembled those sampled from the control reaches, and after restoration more closely resembled those from the reference reaches. Although the macroinvertebrate community responded more favorably than the fish community, both communities recovered quickly from the temporary impairment caused by the disturbance of restoration procedures and suggest rapid improvement in local ecological conditions.

Physics basis and mechanical design of the actively cooled duct scraper protection for the JET neutral beam enhancement

Energy Technology Data Exchange (ETDEWEB)

Wilson, D.J. [UKAEA Fusion/Euratom Association, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom)], E-mail: dwilson@jet.uk; Ciric, D.; Cox, S.J.; Jones, T.T.C.; Kovari, M. [UKAEA Fusion/Euratom Association, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Li Puma, A. [Association EURATOM-CEA, CEA-Cadarache, 13108 St. Paul-Lez-Durance (France); Martin, D.; Milnes, J.; Shannon, M.; Surrey, E. [UKAEA Fusion/Euratom Association, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom)

2007-10-15

The objectives of the JET neutral beam enhancement (NBE) include raising the delivered power from the present 25 MW to more than 34 MW and increasing the pulse length from 10 to 20 s. The additional power will be obtained partly by increasing the fractional energy components of the beam, resulting from acceleration of molecular ions, hence increasing the total particle flux. These changes place extreme demands on the design of the upgraded protection to the torus entry duct. The present inertial duct protection already reaches its thermomechanical limit in 10 s pulses, and active cooling of the upgraded duct protection is therefore essential. Extensive analysis of the pressure and temperature evolution in the present un-cooled duct established the relationship between gas re-emission and surface temperature for copper in this operating environment. This information was used in an integrated physics and engineering approach to the design of the actively cooled duct protection, taking into account the power loads from direct beam interception and re-ionisation. Surface temperature determines power density through the gas re-emission and consequential beam re-ionisation. These considerations define the normal operating point for the chosen enhanced hypervapotron element technology. This approach demonstrated that supplementary in situ duct cryopumping would not be needed, provided that the required heat-transfer performance could be met without any encroachment of the elements beyond the space envelope of the existing inertial duct protection plates. This requirement posed severe constraints on the mechanical design of the hypervapotron element array and its manifolding; the adopted engineering design solutions are presented.

Longitudinal Distribution of the Functional Feeding Groups of Aquatic Insects in Streams of the Brazilian Cerrado Savanna.

Science.gov (United States)

Brasil, L S; Juen, L; Batista, J D; Pavan, M G; Cabette, H S R

2014-10-01

We demonstrate that the distribution of the functional feeding groups of aquatic insects is related to hierarchical patch dynamics. Patches are sites with unique environmental and functional characteristics that are discontinuously distributed in time and space within a lotic system. This distribution predicts that the occurrence of species will be based predominantly on their environmental requirements. We sampled three streams within the same drainage basin in the Brazilian Cerrado savanna, focusing on waterfalls and associated habitats (upstream, downstream), representing different functional zones. We collected 2,636 specimens representing six functional feeding groups (FFGs): brushers, collector-gatherers, collector-filterers, shredders, predators, and scrapers. The frequency of occurrence of these groups varied significantly among environments. This variation appeared to be related to the distinct characteristics of the different habitat patches, which led us to infer that the hierarchical patch dynamics model can best explain the distribution of functional feeding groups in minor lotic environments, such as waterfalls.

POP bioaccumulation in macroinvertebrates of alpine freshwater systems

International Nuclear Information System (INIS)

Bizzotto, E.C.; Villa, S.; Vighi, M.

2009-01-01

This study serves to investigate the uptake of POPs in the different trophic levels (scrapers, collectors, predators, shredders) of macroinvertebrate communities sampled from a glacial and a non-glacial stream in the Italian Alps. The presented results show that the contaminant concentrations in glacial communities are generally higher compared to those from non-glacial catchments, highlighting the importance of glaciers as temporary sinks of atmospherically transported pollutants. Moreover, the data also suggests that in mountain systems snow plays an important role in influencing macroinvertebrate contamination. The main chemical uptake process to the macroinvertebrates is considered to be bioconcentration from water, as similar contaminant profiles were observed between the different trophic levels. The role of biomagnification/bioaccumulation is thought to be absent or negligible. The enrichment of chemicals observed in the predators is likely to be related to their greater lipid content compared to that of other feeding groups. - Influence of POP release in glacial-fed streams, enhanced by global warming, on pristine aquatic ecosystems.

Efficient cascaded parameter scan approach for studying top-off safety in storage rings

Directory of Open Access Journals (Sweden)

Yongjun Li

2011-03-01

Full Text Available We introduce a new algorithm, which we call the cascaded parameter scan method, to efficiently carry out the scan over magnet parameters in the safety analysis for top-off injection in synchrotron radiation storage rings. In top-off safety analysis, one must track particles populating phase space through a beam line containing magnets and apertures and clearly demonstrate that, for all possible magnet settings and errors, all particles are lost on scrapers within the properly shielded region. In the usual approach, if one considers m magnets and scans each magnet through n setpoints, then one must carry out n^{m} tracking runs. In the cascaded parameter scan method, the number of tracking runs is reduced to n×m. This reduction of exponential to linear dependence on the number of setpoints n greatly reduces the required computation time and allows one to more densely populate phase space and to increase the number n of setpoints scanned for each magnet.

Design, fabrication and operation of the mechanical systems for the Neutral Beam Engineering Test Facility

International Nuclear Information System (INIS)

Paterson, J.A.; Biagi, L.A.; Fong, M.; Koehler, G.W.; Low, W.; Purgalis, P.; Wells, R.P.

1983-12-01

The Neutral Beam Engineering Test Facility (NBETF) at Lawrence Berkeley Laboratory (LBL) is a National Test Facility used to develop long pulse Neutral Beam Sources. The Facility will test sources up to 120 keV, 50 A, with 30 s beam-on times with a 10% duty factor. For this application, an actively cooled beam dump is required and one has been constructed capable of dissipating a wide range of power density profiles. The flexibility of the design is achieved by utilizing a standard modular panel design which is incorporated into a moveable support structure comprised of eight separately controllable manipulator assemblies. A unique neutralizer design has been installed into the NBETF beamline. This is a gun-drilled moveable brazed assembly which provides continuous armoring of the beamline near the source. The unit penetrates the source mounting valve during operation and retracts to permit the valve to close as needed. The beamline is also equpped with many beam scraper plates of differing detail design and dissipation capabilities

Near term and long term materials issues and development needs for plasma interactive components

International Nuclear Information System (INIS)

Mattas, R.F.

1986-01-01

Plasma interactive components (PICs), including the first wall, limiter blades, divertor collector plates, halo scrapers, and RF launchers, are exposed to high particle fluxes that can result in high sputtering erosion rates and high heat fluxes. In addition, the materials in reactors are exposed to high neutron fluxes which will degrade the bulk properties. This severe environment will limit the materials and designs which can be used in fusion devices. In order to provide a reasonable degree of confidence that plasma interactive components will operate successfully, a comprehensive development program is needed. Materials research and development plays a key role in the successful development of PICs. The range of operating conditions along with a summary of the major issues for materials development is described. The areas covered include plasma/materials interactions, erosion/redeposition, baseline materials properties, fabrication, and irradiation damage effects. Candidate materials and materials development needs in the near term and long term are identified

Impact of bone graft harvesting techniques on bone formation and graft resorption

DEFF Research Database (Denmark)

Saulacic, Nikola; Bosshardt, Dieter D; Jensen, Simon S

2015-01-01

BACKGROUND: Harvesting techniques can affect cellular parameters of autogenous bone grafts in vitro. Whether these differences translate to in vivo bone formation, however, remains unknown. OBJECTIVE: The purpose of this study was to assess the impact of different harvesting techniques on bone fo......: Transplantation of autogenous bone particles harvested with four techniques in the present model resulted in moderate differences in terms of bone formation and graft resorption.......BACKGROUND: Harvesting techniques can affect cellular parameters of autogenous bone grafts in vitro. Whether these differences translate to in vivo bone formation, however, remains unknown. OBJECTIVE: The purpose of this study was to assess the impact of different harvesting techniques on bone...... formation and graft resorption in vivo. MATERIAL AND METHODS: Four harvesting techniques were used: (i) corticocancellous blocks particulated by a bone mill; (ii) bone scraper; (iii) piezosurgery; and (iv) bone slurry collected from a filter device upon drilling. The grafts were placed into bone defects...

Community-Level Response of Fishes and Aquatic Macroinvertebrates to Stream Restoration in a Third-Order Tributary of the Potomac River, USA

Directory of Open Access Journals (Sweden)

Stephen M. Selego

2012-01-01

Full Text Available Natural stream channel design principles and riparian restoration practices were applied during spring 2010 to an agriculturally impaired reach of the Cacapon River, a tributary of the Potomac River which flows into the Chesapeake Bay. Aquatic macroinvertebrates and fishes were sampled from the restoration reach, two degraded control, and two natural reference reaches prior to, concurrently with, and following restoration (2009 through 2010. Collector filterers and scrapers replaced collector gatherers as the dominant macroinvertebrate functional feeding groups in the restoration reach. Before restoration, based on indices of biotic integrity (IBI, the restoration reach fish and macroinvertebrate communities closely resembled those sampled from the control reaches, and after restoration more closely resembled those from the reference reaches. Although the macroinvertebrate community responded more favorably than the fish community, both communities recovered quickly from the temporary impairment caused by the disturbance of restoration procedures and suggest rapid improvement in local ecological conditions.

Removing the by-products acetic acid and NH4+ from the l-tryptophan broth by vacuum thin film evaporation during l-tryptophan production

Directory of Open Access Journals (Sweden)

Qingyang Xu

2018-05-01

Full Text Available Background: During l-tryptophan production by Escherichia coli, the by-products, acetic acid and NH4+, accumulate in the fermentation broth, resulting in inhibited cell growth and activity and decreased l-tryptophan production. To improve the l-tryptophan yield and glucose conversion rate, acetic acid and NH4+ were removed under low-temperature vacuum conditions by vacuum scraper concentrator evaporation; the fermentation broth after evaporation was pressed into another fermenter to continue fermentation. To increase the volatilisation rate of acetic acid and NH4+ and reduce damage to bacteria during evaporation, different vacuum evaporation conditions were studied. Results: The optimum operating conditions were as follows: vacuum degree, 720 mm Hg; concentration ratio, 10%; temperature, 60°C; and feeding rate, 300 mL/min. The biomass yield of the control fermentation (CF and fermentation by vacuum evaporation (VEF broths was 55.1 g/L and 58.3 g/L at 38 h, respectively, (an increase of 5.8%; the living biomass yield increased from 8.9 (CF to 10.2 pF (VEF; an increase of 14.6%. l-tryptophan production increased from 50.2 g/L (CF to 60.2 g/L (VEF (an increase of 19.9%, and glucose conversion increased from 18.2% (CF to 19.5% (VEF; an increase of 7.1%. The acetic acid concentrations were 2.74 g/L and 6.70 g/L, and the NH4+ concentrations were 85.3 mmol/L and 130.9 mmol/L in VEF and CF broths, respectively. Conclusions: The acetic acid and NH4+ in the fermentation broth were quickly removed using the vacuum scraper concentrator, which reduced bacterial inhibition, enhanced bacterial activity, and improved the production of l-tryptophan and glucose conversion rate.How to cite: Xu Q, Bai F, Chen N, et al. Removing the by-products acetic acid and NH4+ from the l-tryptophan broth by vacuum thin film evaporation during l-tryptophan production. Electron J Biotechnol 2018; 33. https://doi.org/10.1016/j.ejbt.2018.04.003. Keywords: Acetic acid

Vertical distribution and temporal changes of 137Cs in soil profiles under various land uses after the Fukushima Dai-ichi Nuclear Power Plant accident

International Nuclear Information System (INIS)

Takahashi, Junko; Tamura, Kenji; Suda, Tomoya; Matsumura, Ryo; Onda, Yuichi

2015-01-01

We monitored the vertical distribution of 137 Cs in soil profiles under eight different land uses for the 2 y after the Fukushima Dai-ichi Nuclear Power Plant accident, and discussed the temporal changes in the early-stage of the migration and the determinants of the initial distribution. The soil samples were collected for four surveys using a scraper plate at each study site, which consisted of three forests (mixed forest, mature cedar, and young cedar), two grasslands (pasture and meadow) and three abandoned agricultural fields (farm land, tobacco field, and paddy field). The land use patterns have a large influence on some soil properties and the migration processes of 137 Cs above ground, resulting in different distribution of 137 Cs in those soil profiles. Specifically, the secondary deposition of 137 Cs from the coniferous canopy, retention of 137 Cs by litter layer, and the homogenization of 137 Cs concentrations in surface soil by natural soil mixing such as the disturbance by cattle grazing, roots growing and the formation of needle ice were important to cause redistribution of the deposited 137 Cs. Only in the paddy field, the 137 Cs inventory in subsurface soils (5–10 cm) gradually increased and comprised 26% of the total 137 Cs in 2 y, showing the downward migration of 137 Cs to subsurface soil. In the other sites, it was considered that 137 Cs were strongly adsorbed by soil particles and rarely migrated downward as soluble form. Vertical distributions during the first survey were able to be used as the initial distributions and were well fitted to the exponential equation. The distribution parameters α (relaxation depth) and β (relaxation mass depth), calculated by the exponential equation were correlated with RIP (r = −0.806, p < 0.05), macro pore (r = 0.651, p = 0.11), and dispersible fine particle content (r = 0.856, p < 0.05). It indicated that the initial distribution would be influenced by the Cs fixation ability of soil, and the

Discovery Mondays: 'The Grid: a universal computer'

CERN Multimedia

2006-01-01

How can one store and analyse the 15 million billion pieces of data that the LHC will produce each year with a computer that isn't the size of a sky-scraper? The IT experts have found the answer: the Grid, which will harness the power of tens of thousands of computers in the world by putting them together on one network and making them work like a single computer achieving a power that has not yet been matched. The Grid, inspired from the Web, already exists - in fact, several of them exist in the field of science. The European EGEE project, led by CERN, contributes not only to the study of particle physics but to medical research as well, notably in the study of malaria and avian flu. The next Discovery Monday invites you to explore this futuristic computing technology. The 'Grid Masters' of CERN have prepared lively animations to help you understand how the Grid works. Children can practice saving the planet on the Grid video game. You will also discover other applications such as UNOSAT, a United Nations...

Bifenthrin causes trophic cascades and alters insect emergence in mesocosms: implication for small streams

Science.gov (United States)

Rogers, Holly; Schmidt, Travis S.; Dabney, Brittanie L.; Hladik, Michelle; Mahler, Barbara J.; Van Metre, Peter C.

2016-01-01

Direct and indirect ecological effects of the widely used insecticide bifenthrin on stream ecosystems are largely unknown. To investigate such effects, a manipulative experiment was conducted in stream mesocosms that were colonized by aquatic insect communities and exposed to bifenthrin-contaminated sediment; implications for natural streams were interpreted through comparison of mesocosm results to a survey of 100 Midwestern streams, USA. In the mesocosm experiment, direct effects of bifenthrin exposure included reduced larval macroinvertebrate abundance, richness, and biomass at concentrations (EC50s ranged 197.6 – 233.5 ng bifenthrin/ g organic carbon) previously thought safe for aquatic life. Indirect effects included a trophic cascade in which periphyton abundance increased after macroinvertebrate scrapers decreased. Adult emergence dynamics and corresponding terrestrial subsidies were altered at all bifenthrin concentrations tested. Extrapolating these results to the Midwestern stream assessment suggests pervasive ecological effects, with altered emergence dynamics likely in 40% of streams and a trophic cascade in 7% of streams. This study provides new evidence that a common pyrethroid might alter aquatic and terrestrial ecosystem function at the regional scale.

Axisymmetric pumping scheme for the thermal barrier in a tandem mirror

International Nuclear Information System (INIS)

Li, X.Z.

1985-09-01

An axisymmetric pumping scheme is proposed to pump the particles that trap in a thermal barrier without invoking the neutral beam or geodesic curvature. In this scheme a magnetic scraper is moved uni-directionally on the barrier peak to push the barely trapped particles into the central cell. We utilize a potential jump that forms at the peak field for sufficiently strong pumping. The non-collisional catching effect has to be limited by setting an upper limit on the scraping frequency of the magnetic bump. On the other hand, the dynamic stability of the pumping scheme sets a lower limit on the scraping frequency. Using the variational method, we are able to estimate the window between these two limits, which seems feasible for the Tara reactor parameter set. A primary calculation shows that the magnetic bump, ΔB/B is about 10 -4 and the scraping frequency, nu/sub sc/, is about 10 +5 sec -1 , which are similar to the parameters required for those for drift pumping

Study on off-momentum tail scraping in the LHC

CERN Document Server

Mirarchi, D; Bruce, R; CERN. Geneva. ATS Department

2014-01-01

A study on o-momentum tail population in the LHC was performed through collimator scraping at high dispersion region. High intensity measurements at the end of a physics ll with 25ns bunch spacing were carried out on 16th December 2012, using primary collimators (TCPs) in the momentum cleaning insertion (IR3) as scrapers. The o-momentum cuts were applied up to the level where the IR3 primary collimator is the aperture bottleneck for all particles outside the bucket, and the TCPs in the betatron cleaning insertion (IR7) are still the primary restriction of aperture of the machine in the transverse plane for particles inside the bucket. This because whether a particle is lost in IR3 or IR7 is not given only by the momentum oset but also by the betatron amplitude, as explained in the text. A signicant decay of the abort gap (AG) population was observed, while moving in the collimator jaw on the side where particles with negative o-momentum are expected. The level of the AG popupation achieved was at a similar le...

Parasitic gastropod bioerosion trace fossil on Cenomanian oysters from Le Mans, France and its ichnologic and taphonomic context

Directory of Open Access Journals (Sweden)

Gérard Breton

2017-03-01

Full Text Available We describe and name Loxolenichnus stellatocinctus Breton and Wisshak igen. et isp. nov., a bioerosion trace fossil on an Upper Cenomanian oyster from Le Mans (France. This trace is attributed here to a parasitic gastropod. The characteristics of this ichnospecies are a combination of one or several, vertical or oblique, complete penetrations, and an asymmetrical attachment etching (fixichnion with a diagnostic set of stellate grooves increasingly distinct towards the margin of the trace. By including two former Oichnus ichnospecies, Loxolenichnus halo comb. nov. and Loxolenichnus taddei comb. nov., Oichnus, is now constrained to pure predation traces (praedichnia. The numerous oysters collected from the Marnes à Pycnodonte biauriculata Formation show associated epibionts and encrusters as well as borers and scrapers. Encrusters comprise 24 taxa while bioerosion trace fossils comprise 17 ichnotaxa ranging from very rare (< 0.1% to quite abundant (81%. The taphonomic history leading to an ex-situ condensation of these oysters is complex. Both the Gnathichnus and Entobia ichnofacies are represented on the shellgrounds, presumably alternatingly.

«By Tray, Scraper and Prokhodnushka»: Prospector’s Gold Mining Development in the Magadanskiy Sovnarhoz in 1957–1962s

Directory of Open Access Journals (Sweden)

Виталий Григорьевич Зеляк

2012-12-01

Full Text Available The author analyzes dynamics of prospector’s gold mining in the Magadanskiy sovnarhoz per 1957–1962s. It has taken the important place in regional structure of gold mining. During 1957–1959 years there was an organizational becoming artels of prospectors. The cost price of prospector’s gold was more cheaply, than on the state extraction. Regional committees of Communist party have rendered very essential support in prospector’s activity in the end of 1950 th. However party bodies have begun the company on restriction of earnings and toughening of the control over prospectors work.

Trophic partitioning among three littoral microcrustaceans: relative importance of periphyton as food resource

Directory of Open Access Journals (Sweden)

Alexandre Bec

2012-07-01

Full Text Available The high species richness of zooplankton communities in macrophytes littoral zones could result from the diversity of potential trophic niches found in such environment. In macrophytes littoral zones, in addition to phytoplankton, neustonic, benthic and epiphytic biofilms can also be potential components of the microcrustacean diet. Here, we investigated the ability of three large cladocerans: Daphnia longispina, Simocephalus vetulus and Eurycercus lamellatus, to develop on periphyton as their only food source or as a complement to a phytoplankton resource in scarce supply. D. longispina exhibited a very low growth and reproduction rates on the periphytic resource and as S. vetulus seems unable to scrape on periphyton. In contrast, E. lamellatus could not grow on phytoplankton, and appears to be an obligatory periphyton scraper. This latter finding contrasts with previous studies suggesting that E. lamellatus could be able to scrap periphyton as well as filter-feed on suspended matter. These differences in feeding strategy probably reflect the different trophic niches occupied by these three species in macrophytes littoral zones, and may explain at least in part their ability to coexist in the same environment.

Ecology of ephemeroptera, plecoptera and trichoptera (insecta) in rivers of the gunung jerai forest reserve: diversity and distribution of functional feeding groups.

Science.gov (United States)

Hamid, Suhaila Ab; Md Rawi, Che Salmah

2014-08-01

A field study was performed to describe the functional feeding groups (FFGs) of Ephemeroptera, Plecoptera and Trichoptera (EPT) in the Tupah, Batu Hampar and Teroi Rivers in the Gunung Jerai Forest Reserve (GJFR), Kedah, Malaysia. Twenty-nine genera belonging to 19 families were identified. The EPTs were classified into five FFGs: collector-gatherers (CG), collector-filterers (CF), shredders (SH), scrapers (SC) and predators (P). In this study, CG and CF were the dominant groups inhabiting all three rivers. Ephemeroptera dominated these rivers due to their high abundance, and they were also the CG (90.6%). SC were the lowest in abundance among all groups. Based on the FFGs, the Teroi River was suitable for CG, whereas the Tupah and Batu Hampar Rivers were suitable for CG and CF. The distribution of FFGs differed among the rivers (CG, χ(2) = 23.6, p = 0.00; SH, χ(2) = 10.02, p = 0.007; P, χ(2) = 25.54, p = 0.00; CF, χ(2) = 21.95, p = 0.00; SC, χ(2) = 9.31, p = 0.01). These findings indicated that the FFGs found in rivers of the GJFR represent high river quality.

Beam monitors and transverse feedback system of TRISTAN Main Ring

International Nuclear Information System (INIS)

Ieiri, T.; Ishii, H.; Kishiro, J.; Mizumachi, Y.; Mori, K.; Nakajima, K.; Ogata, A.; Shintake, T.; Tejima, M.

1987-01-01

The construction of 30 GeV TRISTAN Main Ring (MR) started in 1983 soon after the commissioning of 8 GeV Accumulation Ring (AR). The authors prepared 392 position monitors, 6 synchrotron radiation monitors, 9 screen monitors, 2 DCCT's, 3 scrapers, 12 bunch monitors, transverse feedback systems for two beams and DC separators. Since the required monitoring devices of AR and MR are almost the same, the experiences in AR were very useful in the design of MR monitors. However, machine parameters of two rings are very different and the authors had to review the performance of each item. From the monitor point of view the most important is the difference of revolution frequency; 794.6 kHz for AR and 99.33 kHz for MR. This means that average beam current of MR is 1/8 as small as AR current with the same bunch number and intensity. Therefore, the sensitivity of each monitor must be better in MR. The second difference is that MR should be used as a collider from the beginning. Therefore they must prepare for multi-beam and multi-bunch operation

Radiation protection considerations in the design of the LHC, CERN's large hadron collider

International Nuclear Information System (INIS)

Hoefert, M.; Huhtinen, M.; Moritz, L.E.; Nakashima, H.; Potter, K.M.; Rollet, S.; Stevenson, G.R.; Zazula, J.M.

1996-01-01

This paper describes the radiological concerns which are being taken into account in the design of the LHC (CERN's future Large Hadron Collider). The machine will be built in the 27 km circumference ring tunnel of the existing LEP collider at CERN. The high intensity of the circulating beams (each containing more than 10 14 protons at 7 TeV) determines the thickness specification of the shielding of the main-ring tunnel, the precautions to be taken in the design of the beam dumps and their associated caverns and the radioactivity induced by the loss of protons in the main ring by inelastic beam-gas interactions. The high luminosity of the collider is designed to provide inelastic collision rates of 10 9 per second in each of the two principal detector installations, ATLAS and CMS. These collisions determine the shielding of the experimental areas, the radioactivity induced in both the detectors and in the machine components on either side of the experimental installations and, to some extent, the radioactivity induced in the beam-cleaning (scraper) systems. Some of the environmental issues raised by the project will be discussed. (author)

Summary and presentation of the international workshop on beam induced energy deposition (issues, concerns, solutions)

International Nuclear Information System (INIS)

Soundranayagam, R.

1991-11-01

This report discusses: energy deposition and radiation shielding in antriproton source at FNAL; radiation issues/problems at RHIC; radiation damage to polymers; radiation effects on optical fibre in the SSC tunnel; capabilities of the Brookhaven Radiation Effects Facility; the SSC interaction region; the FLUKA code system, modifications, recent extension and experimental verification; energy particle transport calculations and comparisons with experimental data; Los Alamos High Energy Transport code system; MCNP features and applications; intercomparison of Monte Carlo codes designed for simulation of high energy hadronic cascades; event generator, DTUJET-90 and DTUNUC; Preliminary hydrodynamic calculations of beam energy deposition; MESA code calculations of material response to explosive energy deposition; Smooth particle hydrodynamic; hydrodynamic effects and mass depletion phenomena in targets; beam dump: Beam sweeping and spoilers; Design considerations to mitigate effects of accidental beam dump; SSC beam abort and absorbed; beam abort system of SSC options; unconventional scheme for beam spoilers; low β quadrupoles: Energy deposition and radioactivation; beam induces energy deposition in the SSC components; extension of SSC-SR-1033 approach to radioactivation in LHC and SSC detectors; energy deposition in the SSC low-β IR-quads; beam losses and collimation in the LHC; and radiation shielding around scrapers

The archaeology of drill hole U20bc, Nevada Test Site, Nye County, Nevada

International Nuclear Information System (INIS)

McLane, A.R.; Hemphill, M.L.; Livingston, S.J.; Pippin, L.C.; Walsh, L.A.

1992-01-01

Impacts to four sites near drill hole U20bc on Pahute Mesa in the northwestern part of the Nevada Test Site were mitigated through data recovery. The work was done during 1988 by the Desert Research Institute for the Department of Energy, Nevada Field Office (DOE/NV)- The four sites that warranted data recovery were 26NY3171, 26NY3173, 26NY5561 and 26NY5566. These sites had previously been determined eligible to the National Register of Historic Places. They were temporary camps that contained lithic debitage, projectile points, milling stones and pottery, and therefore contributed significant information concerning the prehistory of the area. The study of the archaeological remains shows that the prehistoric people subsisted on plant foods and game animals as determined by the artifacts including manos, metates, pottery, lithic scrapers, and projectile points. The time sensitive arfifacts (pottery and diagnostic points) suggest that the region was used from about 12,000 B.P. to just before the historic period, possibly 150 years ago. DOE/NV has met its obligation to mitigate adverse impacts to the cultural resources at U20bc. Therefore, it is recommended that this project proceed as planned

A coal combine

Energy Technology Data Exchange (ETDEWEB)

Wlachovsky, I; Bartos, J

1980-02-15

A design is presented for a coal combine, equipped with two drum operational units, on whose both ends of the upper surface of the body, two coal saws are mounted with the help of a lever system. These saws, found in an operational position, form a gap in the block of the coal block, which is not embraced by the drum operational unit. The coal block, found between the gap and the support, falls down onto the longwall scraper conveyor. The lever system of each coal saw is controlled by two hydraulic jacks. One of the jacks is mounted vertically on the facial wall of the body of the combine and is used for the hoisting for the required height of the horizontal arm of the lever, reinforced by one end in the hinge on the body of the combine. On the ''free'' end of that lever, a coal saw is mounted in a hinge-like fashion and which is connected by the hydraulic jack to the horizontal arm of the lever system. This hydraulic jack is used for the clamping of the coal saw to the face.

Secondary production of benthic insects in three cold-desert streams

Energy Technology Data Exchange (ETDEWEB)

Gaines, W.L.

1987-07-01

Aquatic insect production was studied in three cold-desert streams in eastern Washington (Douglas Creek, Snively Springs, and Rattlesnake Springs). The size-frequency method was applied to individual taxa to estimate total insect production. production was also assessed for functional groups and trophic levels in each stream. Optioservus sp. (riffle beetles) and Baetis sp. (mayflies) accounted for 72% of the total insect numbers and 50% of the total biomass in Douglas Creek. Baetis sp. accounted for 42% of the total insect numbers and 25% of the total biomass in Snively Springs. Simulium sp. (blackflies) and Baetis sp. comprised 74% of the total insect numbers and 55% of the total biomass in Rattlesnake Springs. Grazer-scrapers (49%) and collectors (48%) were the most abundant functional groups in Douglas Creek. Collectors were the most abundant functional group in Snively Springs and Rattlesnake Springs. Herbivores and detritivores were the most abundant trophic level in Snively Springs and Rattlesnake Springs. Dipterans (midges and blackflies) were the most productive taxa within the study streams, accounting for 40% to 70% of the total community production. Production by collectors and detritivores was the highest of all functional groups and trophic levels in all study streams.

Retort

Energy Technology Data Exchange (ETDEWEB)

Salerni, P M

1928-03-28

A retort is described for the distillation of carbonaceous material, such as coal, oil shale, and the like, for the recovery of hydrocarbon oils, in which the coal is fed on to annular trays which are surrounded by shrouds having projecting rims. The coal is agitated in each of the trays by stirring members which are attached by links and to a rotary structure which is rotated by worm gearing. A gap is provided in each rim through which the material is transferred from each tray to the next succeeding lower tray, and in falling through the gap it drops on to the rim of the shroud of the next succeeding lower tray and the residue finally drops into a trough and a scraper on the rotatable ring directs it into an outlet. Vapors are drawn off through outlets. A central heating space contains a fireclay tube having a combustion chamber with burners at the lower part. The products of combustion pass through openings into the space, and thence through an outlet into a hopper for preheating the coal which is to be supplied to the trays.

Leakage detection in underground gas mains with radioaktive argon

International Nuclear Information System (INIS)

Schmitz, J.

1975-01-01

In the field of gas supply, radionuclide techniques are suitable for the routine monitoring of transport mains by means of highly active tracer clouds and a measuring scraper as well as for exact leakage detection in local gas distribution systems. Very good results are obtained in the case of mains lying lower than 1.5 m if the length and alignment of the pipe section allow a towing probe to be pulled through. This was investigated systematically on a model stretch under practical conditions. The attempts to detect leakages were made with the aid of the radioactive isotope 41 Ar. Under conditions close to practice concerning pipe bedding, branching, pre-pressure, and leakage diameter, a leak with leakage rates as small as approx. 1 l/min could be measured with the aid of a towing probe with a precision of +-0.5 m. This accuracy is another advantage of this method. Branching and fittings with a big dead volume do not interfere with the evaluation. The investment for this method can be compared to other physical/technical investigations on mains, e.g. weld seam tests. (orig./LN) [de

Center post type cyclo-speed reducer for sludge scrapers for sedimentation ponds; Chindenchi odei kakiyosekiyo center post gata saikuro {reg_sign} gensokuki

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-04-20

This equipment is a compact center post type cyclo-speed reducer composed by combining an internal gear with the cyclo-speed reducer which is in wide use for water treatment equipment. The features are as follows: (1) Drastic size reduction by adopting a direct-coupled structure of the vertical cyclo-speed reducer and an internal gear, (2) High efficiency by combining an internal gear with the cyclo-speed reducer, (3) Easy maintenance and inspection by a simple speed-reducing mechanism. (4) Cyclo-speed reducer with a torque limiter being in wide use as safety device, (5) Torque limiters corresponding to the specifications of various cyclo-speed reducers, and (6) Low price and short delivery time by modification from a previous revolving bearing to a rail rolling bearing, and standardization of main parts. (translated by NEDO)

High heat flux (HHF) elements for negative ion systems on ITER

International Nuclear Information System (INIS)

Milnes, J.; Chuilon, B.; Xue, Y.; Martin, D.; Waldon, C.

2007-01-01

Negative Ion Neutral Beam systems on ITER will require actively cooled scrapers and dumps to process and shape the beam before injection into the tokamak. The scale of the systems is much larger than any presently operating, bringing challenges for designers in terms of available sub cooling, total pressure drop, deflection and mandatory remote maintenance. High heat fluxes (∼15-20 MW/m 2 ), pulse lengths in excess of 3000 s and high number of cycles pose new challenges in terms of stress and fatigue life. The designs outlined in the Design Description Document for the ITER Neutral Beam System [N53 DDD 29 01-07-03 R 0.1. ITER Design Description Document, DDD 5.3, Neutral Beam H and CD system (including Appendices).], based on swirl tubes, have been reviewed as part of the design process and recommendations made. Additionally, alternative designs have been proposed based on the Hypervapotron high heat flux elements with modified geometry and drawing upon a vast background knowledge of large scale equipment procurement and integration. A full thermo-mechanical analysis of all HHF components has also been undertaken based on ITER design criteria and the limited material data available. The advantages and disadvantages of all designs are presented and recommendations for improvements discussed

Bio-mechanical removing of contaminated soils: a field experiment

International Nuclear Information System (INIS)

Jouve, A.; Maubert, H.; Schulte, E.

1992-01-01

If, in spite of safety precautions, a major nuclear accident would occur, countermeasures should be taken to attenuate the impact of radioactive deposits. The European RESSAC program (REhabilitation of Soils and Surfaces after an ACcident) aims at studying actions for normal life return in contaminated zones. One of them, called the Decontaminating Vegetal Network (D.V.N.) associates the biological action of turfing plants, producing a dense root-network capable to trap the top contaminated soil particles, and the mechanical efficiency of a turf harvester which can remove only 1 cm of soil. This performance, not associated with other techniques of soil removal such as scrapers or bulldozers, leads to minimize the waste production. The D.V.N is a vegetal cover spread over the contaminated soil, using the hydro-seeding technique. The growing plants are forming a pleasant lawn which may have a positive impact on the public opinion compared to techniques using bitumen mixtures to cover the soil. Field experiments involving labelling solutions of stable molybdenum salts simulating the contamination of the soil have shown that this technique can be applied as well on homogeneous cultivated soil surfaces as on roughly ploughed soils. 4 refs., 3 figs., 2 tabs

Responses of macroinvertebrate community metrics to a wastewater discharge in the Upper Blue River of Kansas and Missouri, USA

Science.gov (United States)

Poulton, Barry C.; Graham, Jennifer L.; Rasmussen, Teresa J.; Stone, Mandy L.

2015-01-01

The Blue River Main wastewater treatment facility (WWTF) discharges into the upper Blue River (725 km2), and is recently upgraded to implement biological nutrient removal. We measured biotic condition upstream and downstream of the discharge utilizing the macroinvertebrate protocol developed for Kansas streams. We examined responses of 34 metrics to determine the best indicators for discriminating site differences and for predicting biological condition. Significant differences between sites upstream and downstream of the discharge were identified for 15 metrics in April and 12 metrics in August. Upstream biotic condition scores were significantly greater than scores at both downstream sites in April (p = 0.02), and in August the most downstream site was classified as non-biologically supporting. Thirteen EPT taxa (Ephemeroptera, Plecoptera, Trichoptera) considered intolerant of degraded stream quality were absent at one or both downstream sites. Increases in tolerance metrics and filtering macroinvertebrates, and a decline in ratio of scrapers to filterers all indicated effects of increased nutrient enrichment. Stepwise regressions identified several significant models containing a suite of metrics with low redundancy (R2 = 0.90 - 0.99). Based on the rapid decline in biological condition downstream of the discharge, the level of nutrient removal resulting from the facility upgrade (10% - 20%) was not enough to mitigate negative effects on macroinvertebrate communities.

Overview of the Conceptual Design of the Future VENUS Neutron Imaging Beam Line at the Spallation Neutron Source

Science.gov (United States)

Bilheux, Hassina; Herwig, Ken; Keener, Scott; Davis, Larry

VENUS (Versatile Neutron Imaging Beam line at the Spallation Neutron Source) will be a world-class neutron-imaging instrument that will uniquely utilize the Spallation Neutron Source (SNS) time-of-flight (TOF) capabilities to measure and characterize objects across several length scales (mm to μm). When completed, VENUS will provide academia, industry and government laboratories with the opportunity to advance scientific research in areas such as energy, materials, additive manufacturing, geosciences, transportation, engineering, plant physiology, biology, etc. It is anticipated that a good portion of the VENUS user community will have a strong engineering/industrial research focus. Installed at Beam line 10 (BL10), VENUS will be a 25-m neutron imaging facility with the capability to fully illuminate (i.e., umbra illumination) a 20 cm x 20 cm detector area. The design allows for a 28 cm x 28 cm field of view when using the penumbra to 80% of the full illumination flux. A sample position at 20 m will be implemented for magnification measurements. The optical components are comprised of a series of selected apertures, T0 and bandwidth choppers, beam scrapers, a fast shutter to limit sample activation, and flight tubes filled with Helium. Techniques such as energy selective, Bragg edge and epithermal imaging will be available at VENUS.

Investigations of slope stability, Savannah River Plant, Aiken, South Carolina. Draft report

International Nuclear Information System (INIS)

1985-01-01

Our analysis of slope stability indicates acceptable factors of safety for trenches excavated at a slope inclination of one (horizontal) to one (vertical). Further, without the addition of externally applied loads, such as construction trafficking and the gantry crane, a slope inclination of 0.75 horizontal to 1.0 vertical was found to have an acceptable factor of safety of 1.5. Setback distances were calculated for a slope inclination of one to one, and it was found that the gantry crane loading could safely be applied at a setback distance of approximately 7.5 feet while maintaining a factor of safety of approximately 1.2. Similarly, setback distances required for dump trucks and scrapers would be expected to be approximately 6 feet and 10 feet, respectively, to maintain a factor of safety of 1.2. In order to allow flexibility with construction loadings, parametric studies were utilized for construction trafficking to enable setback distances to be selected consistent with actual equipment to be utilized during construction. The effect of removal of surficial soils was investigated, and it is concluded that a minimum of 4-1/2 feet should be removed from all areas prior to the excavation of slopes

Overview of the conceptual design of the future VENUS beamline at the Spallation Neutron Source

Energy Technology Data Exchange (ETDEWEB)

Bilheux, Hassina Z [ORNL; Herwig, Kenneth W [ORNL; Keener, Wylie S [ORNL; Davis, Larry E [ORNL

2015-01-01

VENUS will be a world-class neutron-imaging instrument that will uniquely utilize the Spallation Neutron Source (SNS) time-of-flight (TOF) capabilities to measure and characterize objects across several length scales (mm to m). When completed, VENUS will provide academia, industry and government laboratories with the opportunity to advance scientific research in areas such as energy, materials, additive manufacturing, geosciences, transportation, engineering, plant physiology, biology, etc. It is anticipated that a good portion of the VENUS user community will have a strong engineering/industrial research focus. Installed at Beamline 10 (BL10), VENUS will be a 25-m neutron imaging facility with the capability to fully illuminate (i.e., umbra illumination) a 20 cm x 20 cm detector area. The design allows for a 28 cm x 28 cm field of view when using the penumbra to 80% of the full illumination flux. A sample position at 20 m will be implemented for magnification measurements. The optical components are comprised of a series of selected apertures, T0 and bandwidth choppers, beam scrapers, a fast shutter to limit sample activation, and flight tubes filled with Helium. Techniques such as energy selective, Bragg edge and epithermal imaging will be available at VENUS

Design of a beam dump for the IFMIF-EVEDA accelerator

International Nuclear Information System (INIS)

Branas, B.; Iglesias, D.; Arranz, F.; Barrera, G.; Casal, N.; Garcia, M.; Gomez, J.; Lopez, D.; Martinez, J.I.; Martin-Fuertes, F.; Ogando, F.; Oliver, C.; Sanz, J.; Sauvan, P.; Ibarra, A.

2009-01-01

The IFMIF-EVEDA accelerator will be a 9 MeV, 125 mA cw deuteron accelerator prototype for verifying the validity of the accelerator design for IFMIF. A beam stop will be used for the RFQ and DTL commissioning as well as for the EVEDA accelerator tests. Therefore, this component must be designed to stop 5 MeV and 9 MeV deuteron beams with a maximum power of 1.13 MW. The first step of the design is the beam-facing material selection. The criteria used for this selection are low neutron production, low activation and good thermomechanical behavior. In this paper, the mechanical analysis and radioprotection calculations that have led to the choice of the main beam dump parameters will be described. The present design is based on a conical beam stop (2.5 m length, 30 cm diameter, and 3.5 mm thickness) made of copper plus a cylindrical 0.5 m long beam scraper. The cooling system is based on an axial high velocity flow of water. This design is compliant with the mechanical design rules during full power stationary operation of the accelerator. The radioprotection calculations performed demonstrate that, with an adequate local shielding, doses during beam on/off phases are below the limits.

How low can you go? Impacts of a low-flow disturbance on aquatic insect communities.

Science.gov (United States)

Walters, Annika W; Post, David M

2011-01-01

The natural hydrology of streams and rivers is being extensively modified by human activities. Water diversion, dam construction, and climate change have the potential to increase the frequency and intensity of low-flow events. Flow is a dominant force structuring stream aquatic insect communities, but the impacts of water diversion are poorly understood. Here we report results of an experimental stream flow diversion designed to test how aquatic insect communities respond to a low-flow disturbance. We diverted 40% to 80% of the water in three replicate streams for three summers, leading to summer flow exceedance probabilities of up to 99.9%. Shifts in habitat availability appeared to be a major driver of aquatic insect community responses. Responses also varied by habitat type: total insect density decreased in riffle habitats, but there was no change in pool habitats. Overall, the total biomass of aquatic insects decreased sharply with lowered flow. Collector-filterers, collector-gatherers, and scrapers were especially susceptible, while predatory insects were more resistant. Despite extremely low flow levels, there was no shift in aquatic insect family richness. The experimental water withdrawal did not increase water temperature or decrease water quality, and some wetted habitat was always maintained, which likely prevented more severe impacts on aquatic insect communities.

Design of an ARM-based Automatic Rice-Selling Machine for Cafeterias

Directory of Open Access Journals (Sweden)

Zhiliang Kang

2016-02-01

Full Text Available To address the problems of low selling efficiency, poor sanitation conditions, labor-intensive requirement, and quick rice cooling speed in manual rice selling in cafeterias, especially in colleges and secondary schools, this paper presented an Advanced RISC Machines (ARM microprocessor-based rice-selling machine for cafeterias. The machines consisted of a funnel-shaped rice bin, a thermal insulation box, and a conveying and scattering mechanism. Moreover, this machine exerts fuzzy control over stepper motor rpm, and the motor drives the conveyor belt with a scraper to scatter rice, deliver it, and keep it warm. Apart from an external 4*4 keyboard, a point of sale (POS machine, an ARM process and a pressure sensor, the machine is also equipped with card swiping and weighting mechanisms to achieve functions of card swiping payment and precise measurement, respectively. In addition, detection of the right amount of rice and the alarm function are achieved using an ultrasonic sensor and a beeper, respectively. The presence of the rice container on the rice outlet is detected by an optoelectronic switch. Results show that this rice-selling machine achieves precise measurement, quick card swiping, fast rice selling, stable operation, and good rice heat preservation. Therefore, the mechanical design enables the machine to achieve its goals.

DESIGN AND EXPERIENCE WITH THE WS/HS ASSEMBLY MOVEMENT USING LABVIEW VIS, NATIONAL INSTRUMENT MOTION CONTROLLERS, AND COMPUMOTOR ELECTRONIC DRIVE UNITS AND MOTORS

International Nuclear Information System (INIS)

Barr, D.S.; Day, L.A.

2001-01-01

The Low-Energy Demonstration Accelerator (LEDA), designed and built at the Los Alamos National Laboratory, is part of the Accelerator Production of Tritium (APT) program and provides a platform for measuring high-power proton beam-halo formation. The technique used for measuring the beam halo employs nine combination Wire Scanner and Halo Scraper (WS/HS) devices. This paper will focus on the experience gained in the use of National Instrument (NI) LabVIEW VIs and motion controllers, and Compumotor electronic drive units and motors. The base configuration couples a Compumotor motor driven by a Parker-Hannifin Gemini GT Drive unit. The drive unit is controlled by a NI PXI-7344 controller card, which in turn is controlled by a PC running custom built NI LabVIEW VIs. The function of the control VI's is to interpret instructions from the main control system, the Experimental Physics and Industrial Control System (EPICS), and carry out the corresponding motion commands. The main control VI has to run all nineteen WS/HS motor axes used in the accelerator. A basic discussion of the main accelerator control system, EPICs which is hosted on a VXI platform, and its interface with the PC based LabVIEW motion control software will be included

ANALISIS TOTAL PRODUCTIVE MAINTENANCE DENGAN METODE OVERALL EQUIPMENT EFFECTIVENESS DAN FUZZY FAILURE MODE AND EFFECTS ANALYSIS

Directory of Open Access Journals (Sweden)

Supriyadi Supriyadi

2017-11-01

Full Text Available Ash Handling System merupakan suatu bagian dari pembangkit listrik tenaga uap dengan bahan bakar batu bara yang berfungsi untuk menyalurkan limbah pembuangan sisa hasil proses pembakaran batu bara pada boiler. Sisa pembakaran terbagi menjadi fly ash dan bottom ash. Untuk sisa pembakaran fly ash akan disalurkan menuju ke Electrostatic Precipitator untuk ditangkap  dengan metode corona dan ditransfer menuju penampungan fly ash dengan cara dimampatkan bersama udara dari kompresor yang melalui pipa-pipa dan tabung transporter. Sedangkan untuk sisa pembakaran bottom ash akan disalurkan dengan alat yang disebut SSC (Submerged Scraper Conveyor. Gangguan pada SSC dapat terjadi mulai dari belt putus, masalah pada penggerak, hingga masalah pada kelistrikan dan instrumennya. Penelitian ini bertujuan untuk mengetahui nilai OEE, mengetahui dampak gangguan belt sobek, mengetahui penyebab terjadinya belt conveyor sobek dan melakukan estimasi hasil perbaikan dari sisi biaya. Penelitian ini menggunakan metode Overall Equipment Effectiveness (OEE dan Fuzzy Failure Mode and Effects Analysis. Hasil penelitian menunjukkan bahwa rata-rata nilai OEE pada tahun 2015 sekitar 52,05%, masih di bawah standar nilai OEE sebesar 85%. Penyebab utamanya adalah adanya gangguan belt sobek karena gesekan belt dengan support return ketika belt conveyor mengalami jogging yang berdampak pada terganggunya penyaluran abu. Modifikasi dapat menghindari kerugian perusahaan sebesar Rp. 582.548.800,00.

Optics of Electron Beam in the Recycler

International Nuclear Information System (INIS)

Burov, A.; Kroc, T.; Lebedev, V.; Nagaitsev, S.; Prost, L.; Pruss, S.; Shemyakin, A.; Sutherland, M.; Warner, A.; Kazakevich, G.; Tiunov, M.

2006-01-01

Electron cooling of 8.9 GeV/c antiprotons in the Recycler ring (Fermilab) requires high current and good quality of the DC electron beam. Electron trajectories of ∼0.2 A or higher DC electron beam have to be parallel in the cooling section, within ∼ 0.2 mrad, making the beam envelope cylindrical. These requirements yielded a specific scheme of the electron transport from a gun to the cooling section, with electrostatic acceleration and deceleration in the Pelletron. Recuperation of the DC beam limits beam losses at as tiny level as ∼0.001%, setting strict requirements on the return electron line to the Pelletron and a collector. To smooth the beam envelope in the cooling section, it has to be linear and known at the transport start. Also, strength of the relevant optic elements has to be measured with good accuracy. Beam-based optic measurements are being carried out and analysed to get this information. They include beam simulations in the Pelletron, differential optic (beam response) measurements and simulation, beam profile measurements with optical transition radiation, envelope measurements and analysis with orifice scrapers. Current results for the first half-year of commissioning are presented. Although electron cooling is already routinely used for pbar stacking, its efficiency is expected to be improved

Analysis on the influence of forest soil characteristics on radioactive Cs infiltration

International Nuclear Information System (INIS)

Mori, Yoshitomo; Yoneda, Minoru; Shimada, Yoko; Shimomura, Ryohei; Fukutani, Satoshi; Ikegami, Maiko

2017-01-01

Soil core (0-5 cm and 5-10 cm) was collected in 5 points with different vegetation in Fukushima Prefecture in order to explore the permeability, field capacity and voidage. Depth profiles of radioactive Cs, ignition loss and CEC (Cation Exchange Capacity) in the 5 forest soils were also investigated, using scraper plate (at 0.5 cm intervals for 0-5 cm and at 1.0 cm intervals for 5-10 cm). Depth profiles in soil layers were totally different between forests and did not show explicit correlation with field capacity, voidage or ignition loss. On the other hand, CEC correlated weakly and permeability did strongly with infiltration of radioactive Cs. Compartment modeling was conducted, so as to reproduce the monitored depth profile, taking ignition loss as a parameter, based on the experiment result that ignition loss had positive correlation with CEC, which might influence the adsorption process on radioactive Cs in soil layer. However, the ignition loss alone failed to fully reproduce the depth profile. Considering the present results as well as the fact that permeability might have explicit relation with infiltration of radioactive Cs, factors related with precipitation or water flow in early stage after the accident could influence the depth profile, before adsorbed with negative charge in soil particles. (author)

Gas plant cleaning case history

Energy Technology Data Exchange (ETDEWEB)

Woods, B

1971-03-22

Basic steps to be taken before using any cleaning method are select a responsible group and give it full responsibility; know the problem, what type of fouling, lab samples, amount of material, time and cost; sell the idea to management; maintain the cleaning equipment; and follow up each cleaning operation. These principles have been applied to advantage in the amine contractor at Taylor, a vessel 60 ft high with 78-in. OD, containing carbon steel deck trays with stainless steel caps. The original attempt to clean with wire scrapers manually involved much lost time and several crews. There was limited space in the tray vessels, design created areas difficult to clean, working conditions were unpleasant, equipment downtime was extended, labor cost was high, and the final result was not satisfactory. Chemical cleaning was substituted, preceded by a water wash. Five hours of caustic wash with a 3% solution at 170$F were followed by a water wash, an acid wash, 1-hr neutralization with a weak soda ash solution, and finally passivation to eliminate iron oxide. For the acid wash, sulfamic acid was found best, in 10% concentration for 4 hr. Cascading was most economical, but flooding has been employed sometimes at 2-1/2 times the cost, to reach all the dark corners.

Plasma-Materials Interactions (PMI) and High-Heat-Flux (HHF) component research and development in the US Fusion Program

International Nuclear Information System (INIS)

Conn, R.W.

1986-10-01

Plasma particle and high heat fluxes to in-vessel components such as divertors, limiters, RF launchers, halo plasma scrapers, direct converters, and wall armor, and to the vacuum chamber itself, represent central technical issues for fusion experiments and reactors. This is well recognized and accepted. It is also well recognized that the conditions at the plasma boundary can directly influence core plasma confinement. This has been seen most dramatically, on the positive side, in the discovery of the H-mode using divertors in tokamaks. It is also reflected in the attention devoted worldwide to the problems of impurity control. Nowadays, impurities are controlled by wall conditioning, special discharge cleaning techniques, special coatings such as carbonization, the use of low-Z materials for limiters and armor, a careful tailoring of heat loads, and in some machines, through the use of divertors. All programs, all experiments, and all designers are now keenly aware that PMI and HHF issues are key to the successful performance of their machines. In this brief report we present general issues in Section 2, critical issues in Section 3, existing US PMI/HHF experiments and facilities in Section 4, US International Cooperative PMI/HHF activities in Section 5, and conclude with a discussion on major tasks in PMI/HHF in Section 6

Membrane Peeling-Induced Retinal Alterations on Intraoperative OCT in Vitreomacular Interface Disorders From the PIONEER Study.

Science.gov (United States)

Ehlers, Justis P; Han, Jaehong; Petkovsek, Daniel; Kaiser, Peter K; Singh, Rishi P; Srivastava, Sunil K

2015-11-01

To assess retinal architectural alterations that occur following membrane peeling procedures and the impact of peel technique on these alterations utilizing intraoperative optical coherence tomography (iOCT). This is a subanalysis of the prospective PIONEER iOCT study of eyes undergoing a membrane peeling for a vitreomacular interface (VMI) disorder. Intraoperative scanning was performed with a microscope-mounted OCT system. Macroarchitectural alterations (e.g., full-thickness retinal elevations) and microarchitectural alterations (e.g., relative layer thickness alterations) were analyzed. Video/iOCT correlation was performed to identify instrument-tissue manipulations resulting in macroarchitectural alterations. One hundred sixty-three eyes were included in the macroarchitectural analysis. Instrumentation utilized for membrane peeling included forceps alone for 73 eyes (45%), combined diamond-dusted membrane scraper (DDMS) and forceps for 87 eyes (53%), and other techniques in three eyes (2%). Focal retinal elevations were identified in 45 of 163 eyes (28%). Video/iOCT correlation identified 69% of alterations involved forceps compared to 26% due to DDMS. Sixteen percent of retinal alterations persisted 1 month following surgery. The microarchitectural analysis included 134 eyes. Immediately following membrane peeling, there was a significant increase in the ellipsoid zone to retinal pigment epithelium height (+20%, P peeling for VMI conditions. Differences in surgical instruments may impact these architectural alterations.

Herd-level risk factors for hock injuries in freestall-housed dairy cows in the northeastern United States and California.

Science.gov (United States)

Barrientos, A K; Chapinal, N; Weary, D M; Galo, E; von Keyserlingk, M A G

2013-06-01

The aim of this study was to investigate the associations between management and facility design factors and the prevalence of hock injuries in high-producing dairy cows in 76 freestall herds in the northeastern United States (NE-US; Vermont, New York, Pennsylvania) and California (CA). One group of high-production multiparous cows was monitored on each farm, and data on management, facility and stall design, and the conditions of the hocks were collected. Focal cows [n=38 ± 3 (mean ± standard deviation)] were evaluated for hock injuries using a 3-point scale (where 1=healthy and 3=evidently swollen or severe injury). Measures associated with the proportion (logit-transformed) of cows having injuries (score ≥ 2) or severe injuries (score=3) at the univariable level were submitted to multivariable general linear models. In NE-US, overall hock injuries increased with the percentage of stalls with fecal contamination [odds ratio (OR)=1.26; 95% confidence interval (CI)=1.02-1.54, for a 10% increase], and with the use of sawdust as bedding (OR=3.47; CI=1.14-10.62), and decreased with deep bedding (i.e., at least 10 cm depth of any type of bedding; OR=0.05; CI=0.02-0.14), use of sand as bedding (OR=0.06; CI=0.02-0.15), bedding dry matter (DM) ≥ 83.9% (OR=0.08; CI=0.03-0.20), and access to pasture during the dry period (OR=0.17; CI=0.05-0.53). When these variables were submitted to a multivariable model, the presence of deep bedding was the only factor that remained significant, explaining 54% of the variation in overall injuries. Severe hock injuries increased with the use of automatic scrapers (OR=2.29; CI=1.11-4.71) and the percentage of stalls with fecal contamination (OR=1.14; CI=1.00-1.31, for a 10% increase), and decreased with sand bedding (OR=0.22; CI=0.10-0.49), deep bedding (OR=0.24; CI=0.11-0.52), bedding DM ≥ 83.9% (OR=0.28; CI=0.14-0.58), and access to pasture during the dry period (OR=0.42; CI=0.18-0.97). The final multivariable model, which

Speciation study of the heavy metals in commercially available recharge cards coatings in Nigeria and the health implication

Directory of Open Access Journals (Sweden)

Abolanle S. Adekunle

2014-01-01

Full Text Available This work assessed levels of heavy metals exposure from silver coatings of mobile phones recharge cards of three major companies (designated as A, B and C with price denominations 100, 200 and 400 from companies A, B and C respectively, which were carefully scratched using a plastic scraper into a glass tube. The coatings were acid digested for total metal concentration, while speciation experiment for Mn, Cu, Cd and Pb was carried out. Total metals and speciation analysis were done using AAS and XRF techniques. The total metal concentration from XRF analysis was in the range: Ca (70–2140 μg/g, K (20–4930 μg/g, Sc (80–270 μg/g, Ti (1530–12,580 μg/g, Fe (50–6660 μg/g, Ni (20–2040 μg/g, Cu (20–850 μg/g and Zn (40–460 μg/g. Cr had the lowest concentration (10 μg/g in A (400 while Ti had the highest concentration (12,580 μg/g in C (500 for all the coatings analyzed. AAS and XRF results agreed closely except for Fe with higher concentration. A (100 contained high concentration of the metals compared with others. Speciation study identified Mn as the most mobile element when present in the environment.

Mongolian “Neolithic” and Early Bronze Age ground stone tools from the northern edge of the Gobi Desert

Directory of Open Access Journals (Sweden)

Joan S. Schneider

2016-10-01

Full Text Available The transition from the Mongolian Neolithic to the Bronze Age is not well understood. Within Ikh Nart Nature Reserve, over a period of five years, we identified a number of sites with dense surface artefact scatters and features that seem to represent this transition period. Evident in those concentrations are characteristic microblade cores, microblades, “thumbnail" flake scrapers, projectile points, ground stone tools, and stone features of unknown function. Between 2012 and 2014 we collected ground stone artefacts from four sites and sediment samples from three sites. With permission of Mongolian authorities, the artefacts from one site and sediment samples from three sites were sent for botanical analyses to the University of Texas, Austin, Environmental Archaeology Laboratory. Preliminary results indicate that plant remains are present on the ground stone artefacts: dendritic long-cells from a deep pore of one artefact and starch grains from the pores of six of the seven artefacts. These data present the first opportunity to understand what resources “Neolithic” people were processing with ground stone tools in this area and further our opportunity to better understand the little-known “Neolithic”-Early Bronze Age transition period in Central Asia. This paper describes the ground stone artefacts and further explores the results of data retrieved from some of these artefacts.

Common pass decentered annular ring resonator

Energy Technology Data Exchange (ETDEWEB)

Holmes, D. A.; Waite, T. R.

1985-04-30

An optical resonator having an annular cylindrical gain region for use in a chemical laser or the like in which two ring-shaped mirrors having substantially conical reflecting surfaces are spaced apart along a common axis of revolution of the respective conical surfaces. A central conical mirror reflects incident light directed along said axis radially outwardly to the reflecting surface of a first one of the ring-shaped mirrors. The radial light rays are reflected by the first ring mirror to the second ring mirror within an annular cylindrical volume concentric with said common axis and forming a gain region. Light rays impinging on the second ring mirror are reflected to diametrically opposite points on the same conical mirror surfaces and back to the first ring mirror through the same annular cylindrical volume. The return rays are then reflected by the conical mirror surface of the first ring mirror back to the central conical mirror. The mirror surfaces are angled such that the return rays are reflected back along the common axis by the central mirror in a concentric annular cylindrical volume. A scraper mirror having a central opening centered on said axis and an offset opening reflects all but the rays passing through the two openings in an output beam. The rays passing through the second opening are reflected back through the first opening to provide feedback.

A first approach to a faunistic crenon typology based on functional feeding groups

Directory of Open Access Journals (Sweden)

Peter NAGEL

2011-09-01

Full Text Available Springs are ecomorphologically and faunistically diverse freshwater ecosystems. Their limnological classification has been a focus of interest since crenic research began. Despite many attempts to include the crenic fauna in the classification of springs, there is no faunistic crenon typology. Over a three-year period we investigated the macroinvertebrate assemblages and the physical, chemical and ecomorphological conditions of 82 springs in the Swiss Jura Mountains, north-western Switzerland. Based on these data we selected the 25 least-disturbed springs to develop a faunistic crenon classification. Based on functional feeding groups we differentiated three crenon groups. An analysis of similarities and nonmetric multidimensional scaling for the substratum types supported the crenon groupings. In general we can distinguish between springs that are dominated by scrapers and characterized by a lotic environment, and those that are mostly inhabited by filtering collectors, associated with a lentic environment. Those two crenon types are the extremes of a continuum. Particular crenon forms, such as those with extensive carbonate deposits, lie between these extremes. This third group is characterized by gathering collectors and shredders. Using this approach we can distinguish faunistic crenon types, based on functional feeding groups, which reflect the abiotic conditions within the springs. We provide a foundation for a faunistic crenon typology which now can be tested in other landscapes and will then be applicable to other low mountain ranges in Europe.

Clasificación trófica de insectos acuáticos en ocho quebradas protegidas de la ecorregión cafetera colombiana

Directory of Open Access Journals (Sweden)

Ana M. Chará-Serna

2010-04-01

Full Text Available Trophic classification of aquatic insects in eight sheltered streams of the Colombian coffee ecoregion. Objective. To determinethe trophic structure of the aquatic insect assembly associated to eight streams in the Colombian coffee-growing ecoregion. Materialsand methods. Aquatic insects were collected in eight forested streams located in La Vieja river basin. The taxa collected were assignedto dietary groups according to a regional classification based on the gut content analysis of aquatic insects associated to forested streamsof the Otún river basin. Results. 2019 individuals belonging to 73 taxa were collected and 60 were classified into dietary groups. Themost abundant group was collectors (55%, followed by shredders (31% and predators (10%. Scrapers represented only 0.05% of thesample and the remaining 3,95% could not be classified due to lack of information. Conclusions. The dominance of collectors andshredders reveals the importance of coarse particulate organic matter (leaf litter as a food resource for the insect fauna. Similaritiesbetween the trophic structure of this community and other communities studied in similar streams, suggest the possibility of a commonpattern for Andean streams. This study evidenced the lack of knowledge on trophic ecology of tropical aquatic insects; 50% of the taxacollected did not have this kind of information for the tropics and 20% had no information neither for the tropics nor temperate zones.

Categorização funcional trófica das comunidades de macroinvertebrados de dois reservatórios na região Centro-Oeste do Estado de São Paulo, Brasil - DOI: 10.4025/actascibiolsci.v31i1.331 Functional feeding groups of benthics macroinvertebrates communities of two lentic systems in the central west region of São Paulo State - DOI: 10.4025/actascibiolsci.v31i1.331

Directory of Open Access Journals (Sweden)

Jandira Liria Biscalquini Talamoni

2009-04-01

Full Text Available A utilização do conceito de guilda pode ser útil para a categorização funcional trófica de comunidades, pois não há obrigatoriedade da identificação dos organismos em nível de espécie, nem de tratar cada espécie como uma entidade separada. O objetivo deste estudo foi analisar os grupos funcionais tróficos (coletores-catadores, coletores-filtradores, fragmentadores, predadores e raspadores das comunidades de macroinvertebrados de dois reservatórios da região Centro-Oeste do Estado de São Paulo, Brasil. As amostragens foram realizadas nos períodos chuvoso (março/abril - 2001 e de seca (julho/agosto - 2001 e os dados obtidos indicam que os coletores-catadores foram a guilda mais frequente. Este fato sugere grande importância da matéria orgânica como recurso alimentar na dieta dos macroinvertebrados analisados.The aim of this study was analyze the functional feeding groups (collectors, shredders, predators and grazer-scrapers of benthic macroinvertebrates communities in two lentic systems in the central west region of São Paulo State. The samples were realized in rainy (March/April - 2001 and dry (July/August - 2001 seasons. The results obtained contribute for the best knowledgement of benthic macroinvertebrate community on those two systems.

Instrumentation for NBI SST-1 cooling water system

International Nuclear Information System (INIS)

Qureshi, Karishma; Patel, Paresh; Jana, M.R.

2015-01-01

Neutral Beam Injector (NBI) System is one of the heating systems for Steady state Superconducting Tokamak (SST-1). It is capable of generating a neutral hydrogen beam of power 0.5 MW at 30 kV. NBI system consists of following sub-systems: Ion source, Neutralizer, Deflection Magnet and Magnet Liner (ML), Ion Dump (ID), V-Target (VT), Pre Duct Scraper (PDS), Beam Transmission Duct (BTD) and Shine Through (ST). For better heat removal management purpose all the above sub-systems shall be equipped with Heat Transfer Elements (THE). During beam operation these sub-systems gets heated due to the received heat load which requires to be removed by efficient supplying water. The cooling water system along with the other systems (External Vacuum System, Gas Feed System, Cryogenics System, etc.) will be controlled by NBI Programmable Logic Control (PLC). In this paper instrumentation and its related design for cooling water system is discussed. The work involves flow control valves, transmitters (pressure, temperature and water flow), pH and conductivity meter signals and its interface with the NBI PLC. All the analog input, analog output, digital input and digital output signals from the cooling water system will be isolated and then fed to the NBI PLC. Graphical Users Interface (GUI) needed in the Wonderware SCADA for the cooling water system shall also be discussed. (author)

Reliability centred maintenance of the cathodic protection system of the Bolivia-Brazil gas pipeline

Energy Technology Data Exchange (ETDEWEB)

Coelho, Jorge Fernando Pereira [Transportadora Brasileira Gasoduto, TBG, Bolivia-Brasil S.A (Brazil)

2004-07-01

This paper presents the results of the Reliability-Centred Maintenance study performed on the Cathodic Protection System of the Bolivia -Brazil Gas Pipeline. The Cathodic Protection installation for the north spread (from Corumba to Guararema, 1413 km) was commissioned in March 1999 and for the south spread (from Campinas to Porto Alegre, 1180 km) one year after. The protection against corrosion of the buried external surface of our gas pipeline is provided, primarily, by an high-efficient external coating, complemented by a impressed current cathodic protection system consisting of: - Forty-one rectifiers and respective anodes ground beds; - One solar panel and respective anodes ground beds; - Fifty-nine insulating joints and respective protective devices; - Nine hundred and ninety pipe-to-soil test stations; - Thirty-six pipe-to-soil remote monitoring devices; - Forty-one electrical power feeder network to the rectifiers. The rectifiers/anodes ground beds are installed at each 50 km approximately, including the solar panel, and the pipe-to-soil test stations at each 2.5 km, under different environment conditions. The insulating joints and theirs protective devices are installed inside stations (launch and receive scrapers, compression and metering) and city-gates, as well, the pipe-to-soil remote monitoring devices. The cathodic protection system and electrical power feeder network are inspected and maintained by a TBG third part Contractor.

Furnaces for destructive distillation

Energy Technology Data Exchange (ETDEWEB)

Gordon, A

1897-12-04

Shale or other material is dropped from a hopper F into an annular retort or kiln A/sup 3/, the walls of which enclose annular flues C, C/sup 1/ in which gas is burnt to heat it. Radial flues also extend across the kiln. The kiln is supported above the ground level by pillars B. The material rests at the bottom on an annular plate H, having a flat middle portion with inclined sides. This is supported within an annular hopper I, provided with counterweighted discharging doors I/sup 1/, held by latches and sealed by placing water on them; or a large conical hopper may be used, provided with a conveyer screw, and containing water. Four long scrapers J are reciprocated radially on the flat part of the plate H by rods J/sup 1/, passed through stuffing-boxes in the hopper, and engaged with eccentric K which are rotated by worm gearing. Doors M in the hopper I, and holes in the plate H, permit stirring-tools to be introduced. The upper part of the kiln consists of iron rings a, a/sup 1/; the products of combustion from the flues pass through openings a/sup 5/ into a central chimney a/sup 3/. The products of distillation are delivered through tubes G.

Fracked ecology: Response of aquatic trophic structure and mercury biomagnification dynamics in the Marcellus Shale Formation.

Science.gov (United States)

Grant, Christopher James; Lutz, Allison K; Kulig, Aaron D; Stanton, Mitchell R

2016-12-01

Unconventional natural gas development and hydraulic fracturing practices (fracking) are increasing worldwide due to global energy demands. Research has only recently begun to assess fracking impacts to surrounding environments, and very little research is aimed at determining effects on aquatic biodiversity and contaminant biomagnification. Twenty-seven remotely-located streams in Pennsylvania's Marcellus Shale basin were sampled during June and July of 2012 and 2013. At each stream, stream physiochemical properties, trophic biodiversity, and structure and mercury levels were assessed. We used δ15N, δ13C, and methyl mercury to determine whether changes in methyl mercury biomagnification were related to the fracking occurring within the streams' watersheds. While we observed no difference in rates of biomagnificaion related to within-watershed fracking activities, we did observe elevated methyl mercury concentrations that were influenced by decreased stream pH, elevated dissolved stream water Hg values, decreased macroinvertebrate Index for Biotic Integrity scores, and lower Ephemeroptera, Plecoptera, and Trichoptera macroinvertebrate richness at stream sites where fracking had occurred within their watershed. We documented the loss of scrapers from streams with the highest well densities, and no fish or no fish diversity at streams with documented frackwater fluid spills. Our results suggest fracking has the potential to alter aquatic biodiversity and methyl mercury concentrations at the base of food webs.

Local Helicity Injection Systems for Non-solenoidal Startup in the PEGASUS Toroidal Experiment

Science.gov (United States)

Perry, J. M.; Barr, J. L.; Bongard, M. W.; Fonck, R. J.; Hinson, E. T.; Lewicki, B. T.; Redd, A. J.

2013-10-01

Local helicity injection is being developed in the PEGASUS Toroidal Experiment for non-solenoidal startup in spherical tokamaks. The effective loop voltage due to helicity injection scales with the area of the injectors, requiring the development of electron current injectors with areas much larger than the 2 cm2 plasma arc injectors used to date. Solid and gas-effused metallic electrodes were found to be unusable due to reduced injector area utilization from localized cathode spots and narrow operational regimes. An integrated array of 8 compact plasma arc sources is thus being developed for high current startup. It employs two monolithic power systems, for the plasma arc sources and the bias current extraction system. The array effectively eliminates impurity fueling from plasma-material interaction by incorporating a local scraper-limiter and conical-frustum bias electrodes to mitigate the effects of cathode spots. An energy balance model of helicity injection indicates that the resulting 20 cm2 of total injection area should provide sufficient current drive to reach 0.3 MA. At that level, helicity injection drive exceeds that from poloidal induction, which is the relevant operational regime for large-scale spherical tokamaks. Future placement of the injector array near an expanded boundary divertor region will test simultaneous optimization of helicity drive and the Taylor relaxation current limit. Work supported by US DOE Grant DE-FG02-96ER54375.

A Multimetric Benthic Macroinvertebrate Index for the Assessment of Stream Biotic Integrity in Korea

Directory of Open Access Journals (Sweden)

Soon-Jin Hwang

2012-10-01

Full Text Available At a time when anthropogenic activities are increasingly disturbing the overall ecological integrity of freshwater ecosystems, monitoring of biological communities is central to assessing the health and function of streams. This study aimed to use a large nation-wide database to develop a multimetric index (the Korean Benthic macroinvertebrate Index of Biological Integrity—KB-IBI applicable to the biological assessment of Korean streams. Reference and impaired conditions were determined based on watershed, chemical and physical criteria. Eight of an initial 34 candidate metrics were selected using a stepwise procedure that evaluated metric variability, redundancy, sensitivity and responsiveness to environmental gradients. The selected metrics were number of taxa, percent Ephemeroptera-Plecoptera-Trichoptera (EPT individuals, percent of a dominant taxon, percent taxa abundance without Chironomidae, Shannon’s diversity index, percent gatherer individuals, ratio of filterers and scrapers, and the Korean saprobic index. Our multimetric index successfully distinguished reference from impaired conditions. A scoring system was established for each core metric using its quartile range and response to anthropogenic disturbances. The multimetric index was classified by aggregating the individual metric ..scores and the value range was quadrisected to provide a narrative criterion (Poor, Fair, Good and Excellent to describe the biological integrity of the streams in the study. A validation procedure showed that the index is an effective method for evaluating stream conditions, and thus is appropriate for use in future studies measuring the long-term status of streams, and the effectiveness of restoration methods.

A Multimetric Benthic Macroinvertebrate Index for the Assessment of Stream Biotic Integrity in Korea

Science.gov (United States)

Jun, Yung-Chul; Won, Doo-Hee; Lee, Soo-Hyung; Kong, Dong-Soo; Hwang, Soon-Jin

2012-01-01

At a time when anthropogenic activities are increasingly disturbing the overall ecological integrity of freshwater ecosystems, monitoring of biological communities is central to assessing the health and function of streams. This study aimed to use a large nation-wide database to develop a multimetric index (the Korean Benthic macroinvertebrate Index of Biological Integrity—KB-IBI) applicable to the biological assessment of Korean streams. Reference and impaired conditions were determined based on watershed, chemical and physical criteria. Eight of an initial 34 candidate metrics were selected using a stepwise procedure that evaluated metric variability, redundancy, sensitivity and responsiveness to environmental gradients. The selected metrics were number of taxa, percent Ephemeroptera-Plecoptera-Trichoptera (EPT) individuals, percent of a dominant taxon, percent taxa abundance without Chironomidae, Shannon’s diversity index, percent gatherer individuals, ratio of filterers and scrapers, and the Korean saprobic index. Our multimetric index successfully distinguished reference from impaired conditions. A scoring system was established for each core metric using its quartile range and response to anthropogenic disturbances. The multimetric index was classified by aggregating the individual metric ..scores and the value range was quadrisected to provide a narrative criterion (Poor, Fair, Good and Excellent) to describe the biological integrity of the streams in the study. A validation procedure showed that the index is an effective method for evaluating stream conditions, and thus is appropriate for use in future studies measuring the long-term status of streams, and the effectiveness of restoration methods. PMID:23202765

Long-term change in limnology and invertebrates in Alaskan boreal wetlands

Science.gov (United States)

Corcoran, R.M.; Lovvorn, J.R.; Heglund, P.J.

2009-01-01

Climate change is more pronounced at high northern latitudes, and may be affecting the physical, chemical, and biological attributes of the abundant wetlands in boreal forests. On the Yukon Flats, located in the boreal forest of northeast Alaska, wetlands originally sampled during 1985-1989 were re-sampled for water chemistry and macroinvertebrates in summer 2001-2003. Wetlands sampled lost on average 19% surface water area between these periods. Total nitrogen and most metal cations (Na, Mg, and Ca, but not K) increased between these periods, whereas total phosphorus and chlorophyll a (Chl a) declined. These changes were greater in wetlands that had experienced more drying (decreased surface area). Compared with 1985-1989, densities of cladocerans, copepods, and ostracods in both June and August were much higher in 2002-2003, whereas densities of amphipods, gastropods, and chironomid larvae were generally lower. In comparisons among wetlands in 2002-2003 only, amphipod biomass was lower in wetlands with lower Chl a, which might help explain the decline of amphipods since the late 1980s when Chl a was higher. The decline in Chl a corresponded to greatly increased zooplankton density in June, suggesting a shift in carbon flow from scrapers and deposit-feeders to water-column grazers. Declines in benthic and epibenthic deposit-feeding invertebrates suggest important food web effects of climate change in otherwise pristine wetlands of the boreal forest. ?? 2008 Springer Science+Business Media B.V.

Phytophilous cladocerans (Crustacea, Anomopoda and Ctenopoda from Paranã River Valley, Goiás, Brazil Cladóceros fitófilos (Crustacea, Anomopoda and Ctenopoda do vale do Rio Paranã, Goiás, Brasil

Directory of Open Access Journals (Sweden)

Lourdes M. A. Elmoor-Loureiro

2007-06-01

Full Text Available A rapid assessment survey identified 39 phytophilous cladocerans species from littoral zones of rivers, permanent and temporary lagoons, and swamps of the Paranã River Valley, Goiás, Brazil, 22 are registered for the first time in Central Brazil. Aspects of the taxonomy of some of these species are discussed. Cluster analysis (UPGMA revealed two phytophilous cladoceran assemblages, characterized by higher or lower richness and relative abundance of species of the families Daphniidae and Moinidae (filter feeders, in comparison with the dominant families Chydoridae and Macrothricidae (scraper feeders.Através de amostragens rápidas, levantou-se as espécies de cladóceros fitófilos presentes em zonas litorâneas de rios, lagoas e brejos permanentes e temporários do vale do Rio Paranã, Goiás, Brasil. Foram encontradas 39 espécies, das quais 22 são registradas pela primeira vez na região central do Brasil. São discutidos aspectos da taxonomia de algumas dessas espécies. A análise de agrupamento (UPGMA dos pontos de amostragem mostrou dois tipos de associações de espécies de cladóceros fitófilos, caracterizadas pela maior ou menor riqueza e abundância relativa das espécies das famílias Daphniidae e Moinidae (filtradoras, em contraste com as famílias dominantes Chydoridae e Macrothricidae, tipicamente raspadoras do substrato.

Problems of gas control and fueling in the Tara tandem mirror

International Nuclear Information System (INIS)

Post, R.S.; Horne, S.; Brau, K.; Casey, J.; Golovato, S.; Sevillano, E.; Shuy, G.; Smith, D.K.

1986-10-01

Control of the edge neutral pressure is critical for successful thermal barrier operation of tandem mirrors. High neutral pressures lead to substantial charge exchange losses of plasma ions as well as creating a population of cold ions and electrons which may be electrostatically trapped in the negative and positive confining potentials in the end cells. The primary sources of neutral gas in Tara are central cell and transition gas injection, and neutral beam injection in the plugs. In the central cell, the region of ionization is separated from the mirror-trapped hot ion region. Gettering in the region of hot ions, controls reflux and reduces the central cell gas contribution to the plug. During end plugging, the plasma stream from the central cell which is used to fuel the minimum B anchor cells is cut off, so that gas fueling must be supplied in the transition region. The beamlines and dumps use LN/Ti pumps, baffling and bakeable dumps and scrapers to limit gas penetration to the plug plasma. Gettering of the plug wall and geometric considerations are used to control reflux from charge exchange. Monte-Carlo simulations are used to analyze the plug and central cell reflux. A new central cell configuration employing a midplane magnetic divertor is now being evaluated. The halo plasma produced in the diverted magnetic flux will be used to improve shielding of the core plasma from charge exchange

A test of hypothetical hill-slope-gully-streambed soil redistribution model using fallout cs-137 a first use of the technique in pakistan

International Nuclear Information System (INIS)

Ahmad, M.; Sheikh, M.R.; Akram, W.; Ali, M.; Iqbal, N.

2007-07-01

Soil degradation by water erosion, which is further responsible for sedimentation in the conveyance systems and reservoirs, is a matter of growing concern in Pakistan. Caesium-137, a fallout radioisotope produced from atmospheric nuclear weapon tests, has become a well-established radiotracer of soil movement. To assess the potential for application of caesium-137 as an indicator of soil erosion and sedimentation, a hypothetical hill slope-gully-streambed redistribution model was tested in Mangla Watershed, Pakistan, as a first use of the technique in the country. The results indicate that the soil redistribution along the different components follows the hypothetical model, with severe net soil loss (sheet erosion) at the hill-slope, no labeling of gully head, and high sedimentation on the streambed. The reference inventory of 137CS obtained by scraper plate (4380 Bq m-2 was in agreement with the mean value of bulk cores (i.e. 3945 +- 457 Bq m-2). The net soil loss along the hill slope estimated by the profile distribution model was 17.2 t ha-1 yr-l. The sedimentation rate in the main stream was more before the year 1974 (8 cm yr-l) than afterwards reducing to 5.9 cm yr-1 due to re-vegetation. The 137CS technique proved to be less time consuming in the provision of information on soil redistribution rates than direct measurement would have been and can be used to assess watershed management practices in Pakistan. (author)

High-throughput continuous cryopump

International Nuclear Information System (INIS)

Foster, C.A.

1986-01-01

A cryopump with a unique method of regeneration which allows continuous operation at high throughput has been constructed and tested. Deuterium was pumped continuously at a throughput of 30 Torr.L/s at a speed of 2000 L/s and a compression ratio of 200. Argon was pumped at a throughput of 60 Torr.L/s at a speed of 1275 L/s. To produce continuous operation of the pump, a method of regeneration that does not thermally cycle the pump is employed. A small chamber (the ''snail'') passes over the pumping surface and removes the frost from it either by mechanical action with a scraper or by local heating. The material removed is topologically in a secondary vacuum system with low conductance into the primary vacuum; thus, the exhaust can be pumped at pressures up to an effective compression ratio determined by the ratio of the pumping speed to the leakage conductance of the snail. The pump, which is all-metal-sealed and dry and which regenerates every 60 s, would be an ideal system for pumping tritium. Potential fusion applications are for mpmp limiters, for repeating pneumatic pellet injection lines, and for the centrifuge pellet injector spin tank, all of which will require pumping tritium at high throughput. Industrial applications requiring ultraclean pumping of corrosive gases at high throughput, such as the reactive ion etch semiconductor process, may also be feasible

Leading experience of reaching high labor productivity in the stoping face using grader extraction

Energy Technology Data Exchange (ETDEWEB)

Chikh, M P

1982-01-01

The main factors which hold back highly productive work are high labor intensity of reinforcing the terminal sections of the longwalls, difference in the speed characteristics of the worm and longwall conveyers, jamming of the worm conveyers, holdups in transportation, etc. Consequently under the leadership of the party and trade union organizations, organizational technical measures were developed and are constantly being improved. Shift working meetings are held at which specific solutions are adopted. In order to improve load on the face, specific measures were adopted: measures are regularly developed for maintenance and repair of the stoping face equipment; a cartogram of repair-technical operations is compiled for the longwall; the velocity of the worm conveyers is brought to the velocity of the longwall conveyer, on the scraper conveyers in the conveyer galleries the edge is increased to 0.6 m; supply of electricity to the grader and conveyer in the longwall is done by individual substations; the efficiency experts of the mines have developed and introduced an improved design of belt loader at the loading point; in order to repair equipment on off days, a special group of highly skilled mechanics has been created. Introduction of these measures together will make it possible to improve coal extraction, labor productivity, labor efficiency, reduce accident rate, reveal latent reserves. Practice has indicated that the use of the grader units with mechanized timbering IMKS makes it possible to achieve high technical-economic indicators both of the work of the brigade and the mine as a whole.

Analysis on the influence of forest soil characteristics on radioactive Cs infiltration and evaluation of residual radioactive Cs on surfaces.

Science.gov (United States)

Mori, Yoshitomo; Yoneda, Minoru; Shimada, Yoko; Fukutani, Satoshi; Ikegami, Maiko; Shimomura, Ryohei

2018-03-29

We investigated the depth profiles of radioactive Cs, ignition loss, and cation exchange capacity (CEC) in five types of forest soils sampled using scraper plates. We then simulated the monitored depth profiles in a compartment model, taking ignition loss as a parameter based on experimental results showing a positive correlation between ignition loss and the CEC. The calculated values were comparable with the monitored values, though some discrepancy was observed in the middle of the soil layer. Based on decontamination data on the surface dose rate and surface contamination concentration, we newly defined a surface residual index (SRI) to evaluate the residual radioactive Cs on surfaces. The SRI value tended to gradually decrease in forests and unpaved roads and was much smaller in forests and on unpaved roads than on paved roads. The radioactive Cs was assumed to have already infiltrated underground 18 months after the nuclear power plant accident, and the sinking was assumed to be ongoing. The SRI values measured on paved roads suggested that radioactive Cs remained on the surfaces, though a gradual infiltration was observed towards the end of the monitoring term. The SRI value is thought to be effective in grasping the rough condition of residual radioactive Cs quickly at sites of decontamination activity in the field. The SRI value may be serviceable for actual contamination works after further research is done to elucidate points such as the relation between the SRI and the infiltration of radioactive Cs in various types of objects.

Benthic macroinvertebrates as bioindicators of water quality in an Atlantic forest fragment

Directory of Open Access Journals (Sweden)

Augusto Oliveira

2010-12-01

Full Text Available The objective of this study was to evaluate benthic macroinvertebrate communities as bioindicators of water quality in five streams located in the "Reserva Particular do Patrimônio Natural" (RPPN Mata Samuel de Paula and its surroundings, in the municipality of Nova Lima near the city of Belo Horizonte, Minas Gerais State, southeastern Brazil. This region has been strongly modified by human activities including mining and urbanization. Samples were collected in the field every three months between August 2004 and November 2005, totaling six samplings in the rainy and dry seasons. This assessment identified one area ecologically altered while the other sampling sites were found to be minimally disturbed systems, with well-preserved ecological conditions. However, according to the Biological Monitoring Work Party (BMWP and the Average Score Per Taxon (ASPT indices, all sampling sites had excellent water quality. A total of 14,952 organisms was collected, belonging to 155 taxa (148 Insecta, two Annelida, one Bivalvia, one Decapoda, one Planariidae, one Hydracarina, and one Entognatha. The most abundant benthic groups were Chironomidae (47.9%, Simuliidae (12.3%, Bivalvia (7.5%, Decapoda (6.1%, Oligochaeta (5.2%, Polycentropodidae (3.7%, Hydropsychidae (2.5%, Calamoceratidae (1.8%, Ceratopogonidae (1.7%, and Libellulidae (1.2%. The assessment of the benthic functional feeding groups showed that 34% of the macroinvertebrates were collector-gatherers, 29% predators, 24% collector-filterers, 8% shredders, and 5% scrapers. The RPPN Mata Samuel de Paula comprises diversified freshwater habitats that are of great importance for the conservation of many benthic taxa that are intolerant to organic pollution.

Habitats and trophic relationships of Chironomidae insect larvae from the Sepotuba River basin, Pantanal of Mato Grosso, Brazil.

Science.gov (United States)

Butakka, C M M; Grzybkowska, M; Pinha, G D; Takeda, A M

2014-05-01

Benthic habitats are linked by physical processes and are essential elements in assessing of the distribution dynamics of Chironomidae dipteran insects and their role in aquatic ecosystems. This work presents results of distribution patterns of chironomids larvae in 38 sites that are abundant in the study site, inhabiting the substrate of the main river channel, rapids, tributary brook, floodplain lakes and reservoir along the Sepotuba River from its mouth at the Paraguay River to the headwater region. A total of 1,247 larvae was registered. The most abundant taxa were Polypedilum (Tripodura) sp. (25.2%), Cricotopus sp.3 (23.0%) and Tanytarsus sp. (15.0%). Fissimentum desiccatum were found only in the reservoir; Fissimentum sp.2 and Tanytarsus cf. T. obiriciae sp.2 in floodplain lakes, and Goeldichironomus sp. in the main channel. The low diversity of the sites S06 and S35 is caused by the near-exclusive presence of the species Cricotopus sp.3, alone or together with one or another taxon (Tanytarsus sp., Djalmabatista sp.3). Collectors-filterers represent 16%, collectors-gatherers 15%, predators 11% and scrapers only 1%. The predators dominated in the secondary channel (±88 ind/m2), corresponding to 40% of the total of this group. Cryptochironomus sp.2 (34%) and Ablasbemyia gr. annulata (26%) were the most abundant among the predators. The differences along the river course are decisive for the formation of distinct or discontinuous communities and the limits become obvious though the interrelations between the populations in the community, as for instance, competition for food and habitats.

Insect Residue Contamination on Wing Leading Edge Surfaces: A Materials Investigation for Mitigation

Science.gov (United States)

Lorenzi, Tyler M.; Wohl, Christopher J.; Penner, Ronald K.; Smith, Joseph G.; Siochi, Emilie J.

2011-01-01

Flight tests have shown that residue from insect strikes on aircraft wing leading edge surfaces may induce localized transition of laminar to turbulent flow. The highest density of insect populations have been observed between ground level and 153 m during light winds (2.6 -- 5.1 m/s), high humidity, and temperatures from 21 -- 29 C. At a critical residue height, dependent on the airfoil and Reynolds number, boundary layer transition from laminar to turbulent results in increased drag and fuel consumption. Although this represents a minimal increase in fuel burn for conventional transport aircraft, future aircraft designs will rely on maintaining laminar flow across a larger portion of wing surfaces to reduce fuel burn during cruise. Thus, insect residue adhesion mitigation is most critical during takeoff and initial climb to maintain laminar flow in fuel-efficient aircraft configurations. Several exterior treatments investigated to mitigate insect residue buildup (e.g., paper, scrapers, surfactants, flexible surfaces) have shown potential; however, implementation has proven to be impractical. Current research is focused on evaluation of wing leading edge surface coatings that may reduce insect residue adhesion. Initial work under NASA's Environmentally Responsible Aviation Program focused on evaluation of several commercially available products (commercial off-the-shelf, COTS), polymers, and substituted alkoxy silanes that were applied to aluminum (Al) substrates. Surface energies of these coatings were determined from contact angle data and were correlated to residual insect excrescence on coated aluminum substrates using a custom-built "bug gun." Quantification of insect excrescence surface coverage was evaluated by a series of digital photographic image processing techniques.

Study of the production of compacted peat; Tiivistetyn turpeen tuotantotutkimus

Energy Technology Data Exchange (ETDEWEB)

Erkkilae, A [VTT Energy, Jyvaeskylae (Finland)

1997-12-01

The so-called Compeat method developed at VTT Energy is applied by field experiments to peat production. The aim of the two-year project (1996 - 1997) is to achieve an increase of 20 % in hectare yield with this new production method of compacted peat in pilot scale in field conditions without any increase in production costs. The aim of the 1996 study was to construct a prototype mining machine for compacted peat and to produce compacted peat from Carex and Sphagnum peat fields in test runs. The operation of the mining machine was studied and drying of compacted peat with that of milled peat were compared at peat production sites of Vapo Oy and Turveruukki Oy. The results of the drying studies were along the same lines with previous laboratory drying tests. The dry matter yield of Compeat was more than twice that of milled peat in the Carex peat field and 1.1-1.5-fold in the Sphagnum field. Compeat moistened significantly less in the rain than normally milled peat. Compeat was ridged with a scraper-ridger. The mining machine produced sufficiently compacted and well-drying peat, but its power demand was too high. The aim is to reduce the power consumption of the mining machine significantly to make it possible to use a wheel- tractor for pulling and to reduce the production costs of the method lower than those of the milled peat method. The drying results of Compeat were so promising that the development of the field machine will be continued. (orig.)

Benthic fauna of extremely acidic lakes (pH 2-3)

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, G G

2001-07-01

The structure of the benthic invertebrate communities were investigated in terms of composition, abundance, and biomass from extremely acidic lakes with pH values from 2 to 3 in areas where coal was intensively mined in the Lusatian region in the eastern region of Germany. Benthic invertebrates colonisation on leaves and the breakdown rate processing of the three deciduous leaf: Betula pendula (birch), Fraxinus excelsior (ash), and Juglans regia (walnut) were investigated. Also, the main key-species of these acidic environments were investigated, in terms of description of pupal exuviae of Chironomus crassimanus and the feeding habit of this acid-resistant species through analysis of their gut content. The benthic food web in extremely acidic mining Lusatian lakes is very short in terms of species richness, trophic relationship, guilds and functional feeding groups. Collector-filters and scraper-grazers were absent in extremely acidic mining lakes (AML 107, AML 111 and AML 117). Shredders as Limnophyes minimus (Diptera, Chironomidae, Orthocladiinae) and Hydrozetes lacustris (Acari, Hydrozetidae) occurred in low abundance in AML 107 and AML 111, and it may be in response to slow leaf breakdown process in these ecosystems, except in AML 117 where the H. lacustris contributed most to ecosystems functioning via the processing of litter. Aquatic insects as Sialis lutaria (Megaloptera, Sialidae), Orectochilus villosus (Coleoptera, Gyrinidae), Coenagrion mercuriale (Odonata, Coenagrionidae), and Phryganeidae (Trichoptera) are the top-predators of these ecosystems. They did not depend on the level of pH in the lakes, but on the availability of food resources. (orig.)

Operation of TFTR neutral beams with heavy ions

International Nuclear Information System (INIS)

Kamperschroer, J.H.; Stevenson, T.N.; Wright, K.E.; Dudek, L.E.; Grisham, L.R.; Newman, R.A.; O'Connor, T.E.; Oldaker, M.E.; von Halle, A.; Williams, M.D.

1991-07-01

High Z neutral atoms have been injected into TFTR plasmas in an attempt to enhance plasma confinement through modification of the edge electric field. TFTR ion sources have extracted 9 A of 62 keV Ne + for up to 0.2 s during injection into deuterium plasmas, and for 0.5 s during conditioning pulses. Approximately 400 kW of Ne 0 have been injected from each of two ion sources. Operation was at full bending magnet current, with the Ne + barely contained on the ion dump. Beamline design modifications to permit operation up to 120 keV with krypton or xenon are described. Such ions are too massive to be deflected up to the ion dump. The plan, therefore, is to armor those components receiving these ions. Even with this armor, modest increases in the bending magnet current capability are necessary to safely reach 120 kV with Kr or Xe. Information relevant to heavy ion operation was also acquired when several ion sources were inadvertently operated with water contamination. Spectroscopic analysis of certain pathological pulses indicate that up to 6% of the extracted ions were water. After dissociation in the neutralizer, water yields oxygen ions which, as with Ne, Kr, and Xe, are under-deflected by the magnet. Damage to a calorimeter scraper, due to the focal properties of the magnet, has resulted. A magnified power density of 6 KW/cm 2 for 2 s, from ∼ 90 kW of O + , is the suspected cause. 11 refs., 4 figs

Reclamation of urban areas

International Nuclear Information System (INIS)

Roed, J.

1986-02-01

A literature study was conducted in order to compare the effectiveness and cost of different reclamation procedures that may be employed after an accident on a nuclear facility takes place in which radioactive material is released to the atmosphere. A substantial amount of work has been done on reclaming soil and snow-covered surfaces. Using scrapers or other soil-moving equipment decontamination factors are 10-100. (The decontamination factor is the ratio of the contamination before to that after the decontamination procedure). However, information on decontamination of paved areas by simple methods such as firehosing and vacuum sweeping are poorly documented. Therefore, only a very uncertain figure in the range 2-10 can be given for the decontamination factor here. It is recommended that a major effort be made in the future to investigate the efficiency of these simple methods, because of their relatively low cost. Also, more expensive methods for reducing the dose such as vacuuming, road planing and deep plowing are treated because of their feasibility under certain circumstances. Using these methods dose reduction factors in the 2-100 range can be obtained. Very expensive techniques, such as sandblasting, water cannon, flame spalling, etc. are justifiable usable only in special situations and are therefore considered very briefly here. The methods vary widely in cost. A simple method like vacuum sweeping costs $0.004 per square meter of surface; whereas one like road planing can reach $4 per square meter. A more sophisticated technique like flame spalling costs as much as $100 per square meter. (author)

Design of a negative-ion based NBI system for JT-60U

International Nuclear Information System (INIS)

Kuriyama, M.; Araki, M.; Inoue, T.; Kunieda, S.; Matsuoka, M.; Mizuno, M.; Ohara, Y.; Okumura, Y.; Oohara, H.; Watanabe, K.

1992-01-01

This paper reports on a negative-ion based NBI system which is planned as a key device on the JT-60U in the experiments of current drive and plasma core heating with high density plasmas. The NBI system will inject neutral beams of 500keV, 10MW for 10sec from a beamline with two ion sources. The neutral beam will be injected tangentially in the codirection. Each ion source is a modified volume production-type negative-ion source with cesium vapor. The acceleration current is 22A with deuterium beam, and the current density is 13mA/cm 2 . An operational pressure in the negative-ion generator is less than 0.5 Pa. A three-stage electro static acceleration system is adopted as the accelerator. The beamline length between the ion source and the injection port is 24m. The beamline consists of an ion source tank, neutralizer cells of 10m in length, an ion dump tank and a drift duct. The ion source tank contains large cryopumps to maintain the exit of the ion source sufficiently low. The ion dump tank contains ion deflecting coils, ion dumps for positive and negative ions, a calorimeter, cryopumps and beam scrapers. Residual ions are deflected by the combined magnetic fields produced by the deflecting coils and the stray field form the tokamak. The two sources are connected to an acceleration power supply of 500kV/64A/10sec, while the negative-ion generator power, the extraction voltage, and electron-suppression voltage are fed individually

Analysis of Silicones Released from Household Items and Baby Articles by Direct Analysis in Real Time-Mass Spectrometry

Science.gov (United States)

Gross, Jürgen H.

2015-03-01

Direct analysis in real time-mass spectrometry (DART-MS) enables screening of articles of daily use made of polydimethylsiloxanes (PDMS), commonly known as silicone rubber, to assess their tendency to release low molecular weight silicone oligomers. DART-MS analyses were performed on a Fourier transform ion cyclotron resonance (FT-ICR) mass spectrometer. Flexible silicone baking molds, a watch band, and a dough scraper, as baby articles different brands of pacifiers, nipples, and a teething ring have been examined. While somewhat arbitrarily chosen, the set can be regarded as representative of household items, baby articles, and other objects made of silicone rubber. For comparison, two brands of silicone septa and as blanks a glass slide and a latex pacifier were included. Differences between the objects were mainly observed in terms of molecular weight distribution and occasional release of other compounds in addition to PDMS. Other than that, all objects made of silicone rubber released significant amounts of PDMS during DART analysis. To provide a coarse quantification, a calibration based on silicone oil was established, which delivered PDMS losses from 20 μg to >100 μg during the 16-s period per measurement. Also, the extraction of baking molds in rapeseed oil demonstrated a PDMS release at the level of 1 μg mg-1. These findings indicate a potential health hazard from frequent or long-term use of such items. This work does not intend to blame certain brands of such articles. Nonetheless, a higher level of awareness of this source of daily silicone intake is suggested.

Downstream effects of hydropower production on aquatic macroinvertebrate assemblages in two rivers in Costa Rica.

Science.gov (United States)

Chaves-Ulloa, Ramsa; Umaña-Villalobos, Gerardo; Springer, Monika

2014-04-01

Despite the fact that little is known about the consequences of hydropower production in tropical areas, many large dams (> 15 m high) are currently under construction or consideration in the tropics. We researched the effects of large hydroelectric dams on aquatic macroinvertebrate assemblages in two Costa Rican rivers. We measured physicochemical characteristics and sampled aquatic macroinvertebrates from March 2003 to March 2004 in two dammed rivers, Peñas Blancas and San Lorenzo, as well as in the undammed Chachagua River. Sites above and below the dam had differences in their physicochemical variables, with wide variation and extreme values in variables measured below the dam in the San Lorenzo River. Sites below the dams had reduced water discharges, velocities, and depths when compared with sites above the dams, as well as higher temperatures and conductivity. Sites above dams were dominated by collector-gatherer-scrapers and habitat groups dominated by swimmer-clingers, while sites below dams had a more even representation of groups. In contrast, a comparison between two sites at different elevation in the undammed river maintained a similar assemblage composition. Tributaries might facilitate macroinvertebrate recovery above the turbine house, but the assemblage below the turbine house resembled the one below the dam. A massive sediment release event from the dam decreased the abundance per sample and macroinvertebrate taxa below the dam in the Peñas Blancas River. Our study illustrates the effects of hydropower production on neotropical rivers, highlighting the importance of using multiple measures of macroinvertebrate assemblage structure for assessing this type of environmental impact.

Effects of the “Run-of-River” Hydro Scheme on Macroinvertebrate Communities and Habitat Conditions in a Mountain River of Northeastern China

Directory of Open Access Journals (Sweden)

Haoran Wang

2016-01-01

Full Text Available The main objective of this study was to quantify the impacts of the run of river (ROR scheme on the instream habitat and macroinvertebrate community. We sampled the macroinvertebrate assemblages and collected the habitat variables above and below an ROR hydropower plant: Aotou plant in the Hailang River, China. The effects of the ROR scheme on habitat conditions were examined using regulation-related variables, most of which, particularly the hydrological variables and substrate composition, presented spatial variations along the downstream direction, contributing to heterogeneous conditions between reaches. The macroinvertebrate richness, the density and the diversity metrics showed significant decreases in the “depleted” reach compared with the upper and lower reaches. Approximately 75% of reach-averaged densities and 50% of taxa richness suffered decreases in the “depleted” reach compared with the upper reach. Furthermore, functional feeding groups also showed distinct site differences along the channel. The relative abundance of both collector-gatherers and the scrapers reduced considerably at the “depleted” sites, particularly at the site immediately downstream of the weir. The total variance in the the functional feeding group (FFG data explained by Canonical correlation analysis (CCA was more than 81.4% and the high-loadings factors were depth, flow velocity, DO and substrate composition. We demonstrated that flow diversion at the 75% level and an in-channel barrier, due to the ROR scheme, are likely to lead to poor habitat conditions and decrease both the abundance and the diversity of macroinvertebrates in reaches influenced by water diversion.

Multi-trophic resilience of boreal lake ecosystems to forest fires.

Science.gov (United States)

Lewis, Tyler L; Lindberg, Mark S; Schmutz, Joel A; Bertram, Mark R

2014-05-01

Fires are the major natural disturbance in the boreal forest, and their frequency and intensity will likely increase as the climate warms. Terrestrial nutrients released by fires may be transported to boreal lakes, stimulating increased primary productivity, which may radiate through multiple trophic levels. Using a before-after-control-impact (BACI) design, with pre- and postfire data from burned and unburned areas, we examined effects of a natural fire across several trophic levels of boreal lakes, from nutrient and chlorophyll levels, to macroinvertebrates, to waterbirds. Concentrations of total nitrogen and phosphorus were not affected by the fire. Chlorophyll a levels were also unaffected, likely reflecting the stable nutrient concentrations. For aquatic invertebrates, we found that densities of three functional feeding groups did not respond to the fire (filterers, gatherers, scrapers), while two groups increased (shredders, predators). Amphipods accounted for 98% of shredder numbers, and we hypothesize that fire-mediated habitat changes may have favored their generalist feeding and habitat ecology. This increase in amphipods may, in turn, have driven increased predator densities, as amphipods were the most numerous invertebrate in our lakes and are commonly taken as prey. Finally, abundance of waterbird young, which feed primarily on aquatic invertebrates, was not affected by the fire. Overall, ecosystems of our study lakes were largely resilient to forest fires, likely due to their high initial nutrient concentrations and small catchment sizes. Moreover, this resilience spanned multiple trophic levels, a significant result for ecologically similar boreal regions, especially given the high potential for increased fires with future climate change.

Report of the task force on radioactivation

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-10-01

Estimates have been made of the residual radioactivation of the components of the SSC accelerator and detector complex. Such activation is caused by the loss of a small fraction of the proton beams being transported in the SSC accelerator system, by deliberate removal (dumping) of the beams and by particles created in the proton-proton collisions in the SSC storage rings. Existing methodology that has been successfully used to determine activation levels at other accelerator facilities has also been used to estimate the activation of SSC components in those cases where calculational methods may be applied. In addition, we have used measurements from existing accelerators, primarily the Fermilab and CERN accelerators, to provide the means to estimate activation for those cases in which calculational methods, such as Monte Carlo shower codes, are difficult to apply. We have also used these measurements to check the calculations from the shower codes where possible. We have estimated activation levels and dose rates, where possible, for the following components of the SSC: The abort dumps for both the storage rings and the elements of the injector system; beam Collimators and scrapers; magnets and other apparatus in the region of injection/extraction from one accelerator to another, target stations used to create test beams from the high energy booster; superconducting magnets in the high energy booster and the storage rings; and representative detector elements. We also briefly discuss aspects of handling or dismantling the components most significantly activated and the relevance to decommissioning of the SSC complex. A short description of the decommissioning of the Intersecting Storage Rings at CERN, the only pp collider that has been decommissioned, is included in this report.

Illinois reclaimed soil productivity: Restoration techniques

International Nuclear Information System (INIS)

Smout, G.

1998-01-01

Consolidation Coal Co. (Consol) has nearly 8,000 acres of high capability and prime farmland reclamation responsibility in Illinois. It has been involved in research in the area of restored soil productivity since 1976 with the University of Illinois and Southern Illinois University, Carbondale. Consol maintains an intensive program to demonstrate and test deep tillage equipment. The research and in-house demonstrations identified soil physical strength (compaction) as the main limiting factor to restoring a soil's productive capacity. There are two primary ways to address this issue, prevention and amelioration. The former was not an option for Consol because many acres were already reclaimed and the company had a major scraper fleet. Along with other operators in Illinois, Consol started an aggressive search for equipment and techniques that could loosen compacted soils. In 1987 Consol was the first to use the D.M.I.-Super Tiger deep soil plow, originally developed and manufactured by D.M.I., Inc. of Goodfield, Illinois. This plow is composed of a single parabolic, static shank with a 44-inch wide sweep weighing 1,200 pounds. It is capable of plowing 48 inches deep while leaving the top soil in place. A Caterpillar D9L tractor with 460 horsepower is used to pull the plow. In 1990 the decision was made to commit to this equipment as the best technology currently available. In 1994 Consol received a patent waiver from D.M.I. to build its own plow. The Consol built plow has been in use since the summer of 1995. To date, Consol has plowed over 3,900 acres with a D.M.I. plow

Effects of dietary esfenvalerate exposures on three aquatic insect species representing different functional feeding groups.

Science.gov (United States)

Palmquist, Katherine R; Jenkins, Jeffrey J; Jepson, Paul C

2008-08-01

Given the chemical properties of synthetic pyrethroids, it is probable that compounds, including esfenvalerate, that enter surface waters may become incorporated into aquatic insect food sources. We examined the effect of dietary esfenvalerate uptake in aquatic insects representing different functional feeding groups. We used three field-collected aquatic insect species: A grazing scraper, Cinygmula reticulata McDunnough (Ephemeroptera: Heptageniidae); an omnivorous filter feeder, Brachycentrus americanus Banks (Trichoptera: Brachycentridae); and a predator, Hesperoperla pacifica Banks (Plecoptera: Perlidae). Laboratory-cultured algae were preexposed for 24 h to esfenvalerate concentrations of 0, 0.025, 0.05, and 0.1 microg/L and provided to two C. reticulata age classes (small and final-instar nymphs). Reduction in small nymph growth was observed following three weeks of feeding on algae exposed to 0.05 and 0.1 microg/L of esfenvalerate, and the highest dietary exposure reduced egg production in final-instar nymphs. The diet for B. americanus and H. pacifica consisted of dead third-instar Chironomus tentans larvae preexposed for 24 h to esfenvalerate concentrations ranging between 0.1 and 1.0 microg/L. Consumption of larvae exposed to 0.5 to 1.0 microg/L of esfenvalerate caused case abandonment and mortality in B. americanus caddisfly larvae. Although H. pacifica nymphs readily consumed esfenvalerate-exposed larvae, no adverse effects were observed during the present study. Furthermore, no evidence of esfenvalerate-induced feeding deterrence was found in any of the species tested, suggesting that aquatic insects may not be able to distinguish between pyrethroid-contaminated and uncontaminated food sources. These findings indicate that feeding deterrence is not a factor in regulating aquatic insect dietary exposures to synthetic pyrethroids.

Aquatic insect community structure under the influence of small dams in a stream of the Mogi-Guaçu river basin, state of São Paulo.

Science.gov (United States)

Saulino, H H L; Corbi, J J; Trivinho-Strixino, S

2014-02-01

The fragmentation of lotic systems caused by construction of dams has modified many aquatic communities. The objective of this study was to analyse changes in the aquatic insect community structure by discontinuity of habitat created by dams along the Ribeirão das Anhumas, a sub-basin of the Mogi-Guaçu River (state of São Paulo, Brazil). Entomofauna collection was carried out in 10 segments upstream and downstream of five dams along the longitudinal profile of the stream, with a quick sampling method using a D net (mesh 250 mm) with 2 minutes of sampling effort. The insects were sorted and identified to the lowest possible taxonomic level and analysed by the Shannon diversity index, β diversity, richness estimated by rarefaction curves and relative participation of functional feeding groups. The results showed a slight reduction in diversity in the downstream segments, as well as along the longitudinal profile of the stream. However, there were no significant differences in abundance and richness between the upstream and downstream segments, indicating that the dams did not influence these variables. Differences were observed in the functional feeding groups along the longitudinal profile. Predator and gatherer insects were dominant in all segments analysed. The feeding group of shredders was more abundant in the segment DSIII with the participation of Marilia Müller (Odontoceridae - Trichoptera), although we observed a decrease of shredders and scrapers with the decrease of the canopy cover reducing values of β diversity in the continuum of Ribeirão das Anhumas. This result demonstrated the importance of the conservation of the riparian vegetation in order to maintain the integrity of the stream.

Seasonal persistence of marine-derived nutrients in south-central Alaskan salmon streams

Science.gov (United States)

Rinella, Daniel J.; Wipfi, Mark S.; Walker, Coowe M.; Stricker, Craig A.; Heintz, Ron A.

2013-01-01

Spawning salmon deliver annual pulses of marine-derived nutrients (MDN) to riverine ecosystems around the Pacific Rim, leading to increased growth and condition in aquatic and riparian biota. The influence of pulsed resources may last for extended periods of time when recipient food webs have effective storage mechanisms, yet few studies have tracked the seasonal persistence of MDN. With this as our goal, we sampled stream water chemistry and selected stream and riparian biota spring through fall at 18 stations (in six watersheds) that vary widely in spawner abundance and at nine stations (in three watersheds) where salmon runs were blocked by waterfalls. We then developed regression models that related dissolved nutrient concentrations and biochemical measures of MDN assimilation to localized spawner density across these 27 stations. Stream water ammonium-N and orthophosphate-P concentrations increased with spawner density during the summer salmon runs, but responses did not persist into the following fall. The effect of spawner density on δ15N in generalist macroinvertebrates and three independent MDN metrics (δ15N, δ34S, and ω3:ω6 fatty acids) in juvenile Dolly Varden (Salvelinus malma) was positive and similar during each season, indicating that MDN levels in biota increased with spawner abundance and were maintained for at least nine months after inputs. Delta 15N in a riparian plant, horsetail (Equisetum fluviatile), and scraper macroinvertebrates did not vary with spawner density in any season, suggesting a lack of MDN assimilation by these lower trophic levels. Our results demonstrate the ready assimilation of MDN by generalist consumers and the persistence of this pulsed subsidy in these organisms through the winter and into the next growing season.

Mycobacterium stephanolepidis sp. nov., a rapidly growing species related to Mycobacterium chelonae, isolated from marine teleost fish, Stephanolepis cirrhifer.

Science.gov (United States)

Fukano, Hanako; Wada, Shinpei; Kurata, Osamu; Katayama, Kinya; Fujiwara, Nagatoshi; Hoshino, Yoshihiko

2017-08-01

A previously undescribed rapidly growing, non-pigmented mycobacterium was identified based on biochemical and nucleic acid analyses, as well as growth characteristics. Seven isolates were cultured from samples collected from five thread-sail filefish (Stephanolepis cirrhifer) and two farmed black scraper (Thamnaconus modestus). Bacterial growth occurred at 15-35 °C on Middlebrook 7H11 agar. The bacteria were positive for catalase activity at 68 °C and urease activity, intermediate for iron uptake, and negative for Tween 80 hydrolysis, nitrate reduction, semi-quantitative catalase activity and arylsulfatase activity at day 3. No growth was observed on Middlebrook 7H11 agar supplemented with picric acid, and very little growth was observed in the presence of 5 % NaCl. α- and α'-mycolates were identified in the cell walls, and a unique profile of the fatty acid methyl esters and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) profiles of the protein and cell-wall lipids were acquired. Sequence analysis revealed that the seven isolates shared identical sequences for the 16S rRNA, rpoB, hsp65, recA and sodA genes. Phylogenetic analysis of the five gene sequences confirmed that the isolates were unique, but closely related to Mycobacterium chelonae. Antibiotic susceptibility testing revealed the minimum inhibitory concentration (MIC) of clarithromycin against this novel species was Mycobacterium salmoniphilum. The hsp65 PCR restriction enzyme analysis pattern differed from those of M. chelonae and M. salmoniphilum. Based on these findings, the name Mycobacterium stephanolepidis sp. nov. is proposed for this novel species, with the type strain being NJB0901 T (=JCM 31611 T =KCTC 39843 T ).

Promoting a functional macroinvertebrate approach in the biomonitoring of Italian lotic systems

Directory of Open Access Journals (Sweden)

Richard W. Merritt

2016-06-01

Full Text Available Over fifty years of research on freshwater macroinvertebrates has been driven largely by the state of the taxonomy of these organisms. Significant advances have been and continue to be made in developing ever more refined keys to macroinvertebrate groups. When advances in macroinvertebrate ecological research are restricted by the level of detail in identifications, then analysis by function is a viable alternative. The focus on function, namely adaptations of macroinvertebrates to habitats and the utilization of food resources, has facilitated ecological evaluation of freshwater ecosystems. This classification is based not on what insects eat, but how they obtain their food. These categories are called 'functional feeding groups', as the name implies, denoting their functional role when describing how and where they feed. This is the basis for the functional feeding group (FFG method that was initially developed in the early 1960s. Taxonomy is applied only to the level of detail that allows assignment to one of five functional feeding group categories: detrital shredders, scrapers, filtering collectors, gatherers, and predators. The aim of this short communication, originating from the presentation of R.W. Merritt at the Biomonitoring Symposium in Rome, 2015, is to promote the use of a functional approach in biomonitoring, especially in Italian and European lotic systems. Here, we present two case studies and we discuss the advantages of the method, especially considering the great availability of quantitative data on macroinvertebrates after the implementation of the WFD 2000/60. We are confident that the increase of functional assessment of ecosystem attributes could have important and direct repercussions in the understanding and management of running waters.

Conceptual design of a rapid-cycling synchrotron for the KFA-Juelich spallation neutron source: working papers

International Nuclear Information System (INIS)

1983-01-01

An accelerator group was established at ANL by the request of KFA-Juelich to carry out a conceptual design study and cost estimate for a rapid-cycling synchrotron as a possible first stage program on spallation neutron sources at KFA-Juelich. This set of notes is the individual notes which form the basis of the final report under this proposal prepared in January 1983. The topics covered include: SNQ Synchrotron Lattice-I; injection and extraction orbit; extraction from SNQ-SRA; SRA injection; capture and acceleration considerations in the SNQ-SRA; longitudinal coupling impedance; power supplies for SNQ synchrotron proposals; space charge limits in the SNQ-SRA; error analysis; SNQ-SRA ring magnets preliminary designs and cost; summary of CERN booster 4-ring arrangement; V-lattices for SNQ-SRA and extraction from the V-lattices; rf parameters for capture, acceleration and extraction; some parameters of the SNQ-SRA injector system; Keil-Schnell criterion; risetime of longitudinal resistive wall instability; beam scrapers; a design of the vacuum system; some aspects of vacuum consideration for SNQ-SRA; choice working points; ring magnet power supplies for shaped extaction of 1.1 GeV SNQ; ring magnet design and costs; tune shift due to the fringing field of the quadrupoles; coherent instability due to ions in the residual gas; transverse stabilization of bunched beams; rf acceleration system; injection into the SRA; Landau damping to get transverse stability; chromaticity and amplitude dependent tune controls in the SNQ-SRA; conversion of the SNQ-SRA to a compressor ring; comments on beam loss; summary of longitudinal stability study and transverse stability study for the SNQ-SRA; and the beam stay clear regions of the SNQ-SRA

A comparison of free-stall barns used by modernized Wisconsin dairies.

Science.gov (United States)

Bewley, J; Palmer, R W; Jackson-Smith, D B

2001-02-01

A primary objective of the Wisconsin Dairy Modernization Survey was to compare features of free-stall barns available to dairy producers. This study used data from a large random sample of expanding dairy farms to determine whether the theoretical benefits of particular free-stall configurations bear out under on-farm conditions. Comparisons were made among herds using free-stall barns as their primary housing for new versus remodeled facilities, barn design, bedding used, feed-delivery design, manure removal strategies, animal restraint, maternity areas, overcrowding, and cooling methods. Producers who made the transition from tie-stall housing to free-stall housing were satisfied with this decision. New free-stall barns provided a more desirable environment for the herds than remodeled free-stall barns, although initial investments were higher. When new free-stall barns were compared, herds with four-row barns had higher production, lower somatic cell count, and higher stocking rates than herds with six-row barns. Respondents were more satisfied with four- and six-row barns than with two- and three-row barns. Respondents felt sand provided some advantages for cow comfort, while satisfaction with bedding cost and manure handling was higher with mattresses. Dairy Herd Improvement data showed no difference in milk production or somatic cell count for producers who chose sand or mattress-based free stalls. Respondents were more satisfied with the use of drive-through feeding than other feed-delivery designs. Most producers chose to use tractor scrapers to remove manure; however, producers who used automated systems were more satisfied with manure management. Few differences were observed when comparing self-locking head gates to palpation rails. Overcrowding did not have any adverse affect on production or user satisfaction with feed intake or cow comfort. Using supplemental cooling appeared to facilitate higher production.

Generalized eMC implementation for Monte Carlo dose calculation of electron beams from different machine types.

Science.gov (United States)

Fix, Michael K; Cygler, Joanna; Frei, Daniel; Volken, Werner; Neuenschwander, Hans; Born, Ernst J; Manser, Peter

2013-05-07

The electron Monte Carlo (eMC) dose calculation algorithm available in the Eclipse treatment planning system (Varian Medical Systems) is based on the macro MC method and uses a beam model applicable to Varian linear accelerators. This leads to limitations in accuracy if eMC is applied to non-Varian machines. In this work eMC is generalized to also allow accurate dose calculations for electron beams from Elekta and Siemens accelerators. First, changes made in the previous study to use eMC for low electron beam energies of Varian accelerators are applied. Then, a generalized beam model is developed using a main electron source and a main photon source representing electrons and photons from the scattering foil, respectively, an edge source of electrons, a transmission source of photons and a line source of electrons and photons representing the particles from the scrapers or inserts and head scatter radiation. Regarding the macro MC dose calculation algorithm, the transport code of the secondary particles is improved. The macro MC dose calculations are validated with corresponding dose calculations using EGSnrc in homogeneous and inhomogeneous phantoms. The validation of the generalized eMC is carried out by comparing calculated and measured dose distributions in water for Varian, Elekta and Siemens machines for a variety of beam energies, applicator sizes and SSDs. The comparisons are performed in units of cGy per MU. Overall, a general agreement between calculated and measured dose distributions for all machine types and all combinations of parameters investigated is found to be within 2% or 2 mm. The results of the dose comparisons suggest that the generalized eMC is now suitable to calculate dose distributions for Varian, Elekta and Siemens linear accelerators with sufficient accuracy in the range of the investigated combinations of beam energies, applicator sizes and SSDs.

Macroinvertebrate distribution and aquatic ecology in the Ruoergai (Zoige) Wetland, the Yellow River source region

Science.gov (United States)

Zhao, Na; Xu, Mengzhen; Li, Zhiwei; Wang, Zhaoyin; Zhou, Hanmi

2017-09-01

The Ruoergai (Zoige) Wetland, the largest plateau peatland in the world, is located in the Yellow River source region. The discharge of the Yellow River increases greatly after flowing through the Ruoergai Wetland. The aquatic ecosystem of the Ruoergai Wetland is crucial to the whole Yellow River basin. The Ruoergai wetland has three main kinds of water bodies: rivers, oxbow lakes, and marsh wetlands. In this study, macroinvertebrates were used as indicators to assess the aquatic ecological status because their assemblage structures indicate long-term changes in environments with high sensitivity. Field investigations were conducted in July, 2012 and in July, 2013. A total of 72 taxa of macroinvertebrates belonging to 35 families and 67 genera were sampled and identified. Insecta was the dominant group in the Ruoergai Basin. The alpha diversity of macroinvertebrates at any single sampling site was low, while the alpha diversity on a basin-wide scale was much higher. Macroinvertebrate assemblages in rivers, oxbow lakes, and marsh wetlands differ markedly. Hydrological connectivity was a primary factor causing the variance of the bio-community. The river channels had the highest alpha diversity of macroinvertebrates, followed by marsh wetlands and oxbow lakes. The density and biomass of Gastropoda, collector filterers, and scrapers increased from rivers to oxbow lakes and then to marsh wetlands. The river ecology was particular in the Ruoergai Wetland with the high beta diversity of macroinvertebrates, the low alpha diversity of macroinvertebrates, and the low taxa richness, density, and biomass of EPT (Ephemeroptera, Plecoptera, Trichoptera). To maintain high alpha diversity of macroinvertebrates macroinvertebrates in the Ruoergai Wetland, moderate connectivity of oxbow lakes and marsh wetlands with rivers and measures to control headwater erosion are both crucial.

Macrozoobenthos in the subarctic river Tenojoki as an environmental indicator. Tenojoen pohjaelaeimistoe ympaeristoen laadun kuvaajana

Energy Technology Data Exchange (ETDEWEB)

Lax, H.G.; Koskenniemi, E.; Sevola, P.; Bagge, P.

1993-01-01

The macrozoobenthos of the subarctic river Tenojoki and some of its tributaries was studied in June and September 1989 as a part of the environmental monitoring programme. The river (F = 16 386 km[sup 2], length 300 km, L = 2.4 %, Q varies between 30-400 m[sup 3]/s) is situated on the Finnish-Norwegian border and is characterized by sand bottoms interrupted by shorter reaches of gravel and stone bottoms. The water is usually clear (colour < 40 mg Pt/l) and oligotrophic (tot-P < 10 [mu]g/l). The bottom fauna was sampled from 9 stations in the main river and from one station in each of the 5 major tributaries. The sampling methods used were: kick-sampling and imago hand netting from all stations, colonization substrates (stone baskets and bricks) at 9 stations in the main river. The tax a number of the kick-samples varied from 10-15/station in spring (totally 51 taxa) and from 15-25/station in autumn (totally 69 taxa). In spring the river margin (depth 0-25 cm) seemed to be an important habitat for many species especially in the upper parts of the river. In autumn most of the species occurred on deeper bottoms (depth 50-100 cm). The most common feeding types in spring were the collectors (Amaletus inopinatus, Chironomidae) and in autumn the scrapers (Elmidae, Baetidae, Hydroptllidae) and collectors (Chironomidae). The pollution index (LongScoreSystem) indicated that the conditions in the lower part of the main river was more stressing for the bottom fauna than in the upper part. But up to now it seems as if the organic pollution from settlements have had only positive effects on the benthic community

Categorização funcional trófica das comunidades de macroinvertebrados de dois reservatórios na região Centro-Oeste do Estado de São Paulo, Brasil = Functional trophic categorization of macroinvertebrate communities of two reservoirs in the Midwestern region of São Paulo State, Brazil

Directory of Open Access Journals (Sweden)

Fabio Laurindo da Silva

2009-01-01

Full Text Available A utilização do conceito de guilda pode ser útil para a categorização funcional trófica de comunidades, pois não há obrigatoriedade da identificação dos organismos em nível de espécie, nem de tratar cada espécie como uma entidade separada. O objetivo deste estudo foi analisar os grupos funcionais tróficos (coletores-catadores, coletores-filtradores, fragmentadores, predadores e raspadores das comunidades de macroinvertebrados de dois reservatórios da região Centro-Oeste do Estado de São Paulo, Brasil. As amostragens foramrealizadas nos períodos chuvoso (março/abril - 2001 e de seca (julho/agosto - 2001 e os dados obtidos indicam que os coletores-catadores foram a guilda mais frequente. Este fato sugere grande importância da matéria orgânica como recurso alimentar na dieta dosmacroinvertebrados analisados.The use of the concept of guild can be useful for the functional trophic categorization of communities, because there is no requirement identification of organisms in the level of species and not to treat each species as a separate entity. The aim of this studywas to analyze the functional feeding groups (collectors-gatherers, collectors-filterers, shredders, predators and grazer-scrapers of the macroinvertebrate communities of two reservoirs in the Midwestern region of São Paulo State. Sampling was carried out in rainy(March/April - 2001 and dry (July/August - 2001 seasons and the data obtained indicate that ‘collectors-gatherers’ is the most frequent guild. This fact suggests a great importance of organic matter as a food source in the diet of the macroinvertebrates analyzed.

LOW-ENGINE-FRICTION TECHNOLOGY FOR ADVANCED NATURAL-GAS RECIPROCATING ENGINES

Energy Technology Data Exchange (ETDEWEB)

Victor W. Wong; Tian Tian; Grant Smedley; Jeffrey Jocsak

2004-09-30

This program aims at improving the efficiency of advanced natural-gas reciprocating engines (ANGRE) by reducing piston/ring assembly friction without major adverse effects on engine performance, such as increased oil consumption and emissions. An iterative process of simulation, experimentation and analysis, are being followed towards achieving the goal of demonstrating a complete optimized low-friction engine system. To date, a detailed set of piston/ring dynamic and friction models have been developed and applied that illustrated the fundamental relationships between design parameters and friction losses. Various low-friction strategies and ring-design concepts have been explored, and engine experiments have been done on a full-scale Waukesha VGF F18 in-line 6 cylinder power generation engine rated at 370 kW at 1800 rpm. Current accomplishments include designing and testing ring-packs using a subtle top-compression-ring profile (skewed barrel design), lowering the tension of the oil-control ring, employing a negative twist to the scraper ring to control oil consumption. Initial test data indicate that piston ring-pack friction was reduced by 35% by lowering the oil-control ring tension alone, which corresponds to a 1.5% improvement in fuel efficiency. Although small in magnitude, this improvement represents a first step towards anticipated aggregate improvements from other strategies. Other ring-pack design strategies to lower friction have been identified, including reduced axial distance between the top two rings, tilted top-ring groove. Some of these configurations have been tested and some await further evaluation. Colorado State University performed the tests and Waukesha Engine Dresser, Inc. provided technical support. Key elements of the continuing work include optimizing the engine piston design, application of surface and material developments in conjunction with improved lubricant properties, system modeling and analysis, and continued technology

Influence of Soils, Riparian Zones, and Hydrology on Nutrients, Herbicides, and Biological Relations in Midwestern Agricultural Streams

Science.gov (United States)

Porter, S.

2001-12-01

Chemical, biological, and habitat conditions were characterized in 70 streams in the upper Mississippi River basin during August 1997, as part of the U.S. Geological Survey's National Water-Quality Assessment (NAWQA) Program. The study was designed to evaluate algal and macroinvertebrate responses to high agricultural intensity in relation to nonpoint sources of nutrients and herbicides, characteristics of basin soils, wooded-riparian vegetation, and hydrology. Concentrations and forms of nutrients, herbicides and their metabolites, and seston constituents varied significantly with regional differences in soil properties, ground and surface water relations, density of riparian trees, and precedent rainfall-runoff conditions. Dissolved nitrate concentrations were relatively low in streams with high algal productivity; however, nitrate concentrations increased with basin water yield, which was associated with the regional distribution of rainfall during the month prior to the study. Stream productivity and respiration were positively correlated with seston (phytoplankton) chlorophyll concentrations, which were significantly larger in streams in areas with poorly drained soils and low riparian-tree density. Concentrations of dissolved phosphorus were low in streams where periphyton biomass was high. Periphyton biomass was relatively larger in streams with clear water and low abundance of macroinvertebrates that consume algae. Periphyton biomass decreased rapidly with modest increases in the abundance of scrapers such as snails and certain mayfly taxa. Differences in dissolved oxygen, organic carbon, stream velocity, and precedent hydrologic conditions explained much of the variance in macroinvertebrate community structure. The overall number of macroinvertebrate species and number of mayfly, caddisfly, and stonefly (EPT) taxa that are sensitive to organic enrichment were largest in streams with moderate periphyton biomass, in areas with moderately-well drained soils

The design, fabrication and operation of the mechanical systems for the Neutral Beam Engineering Test Facility

International Nuclear Information System (INIS)

Patterson, J.A.; Fong, M.; Koehler, G.W.; Low, W.; Purgalis, P.; Wells, R.P.

1983-01-01

The Neutral Beam Engineering Test Facility (NBETF) at the Lawrence Berkeley Laboratory (LBL) is a National Test Facility used to develop long pulse Neutral Beam Sources. The Facility will test sources up to 120 keV, 50 A, with 30 s beam-on times with a 10% duty factor. For this application, an actively cooled beam dump is required and one has been constructed capable of dissipating a wide range of power density profiles. The flexibility of the design is achieved by utilizing a standard modular panel design which is incorporated into a moveable support structure comprised of eight separately controllable manipulator assemblies. The thermal hydraulic design of the panels permits the dissipation of 2 kW/cm 2 anywhere on the panel surface. The cooling water requirements of the actively cooled dump system are provided by the closed loop Primary High Pressure Cooling Water System. To minimize the operating costs of continuously running this high power system, a variable speed hydraulic drive is used for the main pump. During beam pulses, the pump rotates at high speed, then cycles to low speed upon completion of the beam shot. A unique neutralizer design has been installed into the NBETF beamline. This is a gun-drilled moveable brazed assembly which provides continuous armoring of the beamline near the source. The unit penetrates the source mounting valve during operation and retracts to permit the valve to close as needed. The beamline also has an inertially cooled duct calorimeter assembly. This assembly is a moveable hinged matrix of copper plates that can be used as a beam stop up to pulse lengths of 50 ms. The beamline is also equipped with many beam scraper plates of differing detail design and dissipation capabilities

Determination of Redistribution of Erosion/Deposition Rate in Cultivated Area Using 137Cs Technique

International Nuclear Information System (INIS)

Nita Suhartini; Syamsul Abbas RAS; Barokah A; Ali Arman L

2004-01-01

The aim of the research is to determine the rate of redistribution of erosion/deposition in cultivated area. The application of 137 Cs technique was carried out at cultivated area in Bojong - Ciawi, with slope less than 10 o and slope length of about 2 km. A reference site was selected at the top of the slope, and this site is flat, open and covered with grass. Two sites in the cultivated area were selected as study site namely LU-I ( 15 x 25 ) m with the distance of 1000 m from the top, and LU-II (17.5 x 20) m with the distance of 1300 m from the top. Sampling of soil at reference site was done by using scraper (20 x 50) cm, while sampling at study site by using core sampling (di = 7 cm). Soil samples were brought to the laboratorium for preparation and analysis of 137 Cs content. Preparation are including of drying, weighing the total dry, sieving and crushing. Analysis of 137 Cs content was done using multi channel analyzer (MCA) that connected to high purity germanium (HPGe), at 661 keV, and the minimum counting time of 16 hours. To estimate the erosion/deposit rate, two mathematical model were used, namely Proportional Model (PM) and Mass Balance Model 1 (MBM1). The result for application of 137 Cs technique showed that MBM1 gives somewhat higher value for deposit rate and somewhat lower value for erosion than PM. Land use - I (LU-I) of Bojong - Ciawi was suffering from erosion with the erosion rate from 1 t/(ha.y) to 13 t/(ha.y), and LU-II has deposit rate from 1 t/(ha.y) to 50 t/(ha.y). (author)

The impact of sediment removal on the aquatic macroinvertebrate assemblage in a fishpond littoral zone

Directory of Open Access Journals (Sweden)

Zdeněk ADÁMEK

2011-02-01

Full Text Available Bottom sediment removal, a widely used technique in restoration management of standing water bodies, has a strong influence on communities of aquatic organisms. As most information on the impact of sediment removal on the aquatic environment comes from studies on lakes, the aim of this study was to describe macroinvertebrate assemblage succession in a fishpond (Štěpánek fishpond, Bohemian-Moravian highlands, Czech Republic littoral zone following restoration by sediment removal during the winter of 2003/2004. Semi-quantitative hand net sampling was undertaken one year before (2003 and in each of the following five years (2004–2008 after sediment removal. A significant decrease in both abundance (approx. 90% of individuals and diversity (approx. 30% of taxa of macroinvertebrates was detected immediately after pond restoration. The values gradually increased over subsequent years, reaching comparable abundance and diversity three years after sediment removal. A significant shift was recorded in the taxonomic and functional composition of the macroinvertebrate assemblage after sediment removal. Mayfly larvae were the dominant invertebrates before restoration, while chironomid larvae and oligochaetes dominated after sediment removal. Phytophilous taxa, grazers and scrapers, and swimming or diving invertebrates were common in 2003, whilst open-water taxa preferring mud and other mostly inorganic microhabitats, gatherers/collectors, and burrowing/boring invertebrates were relatively common after sediment removal. In 2008, the assemblage reverted towards the situation before sediment removal, probably connected with a lower water level and accelerated macrophyte bed succession. Principal Component Analysis on the species data confirmed the differences in invertebrate taxonomic structure among sampling years. Succession of the fishpond invertebrate assemblage in the years following sediment removal was mainly influenced by fish farming practice and

Guayabero I: un sitio precerámico de la localidad Angostura II, San José del Guaviare Guayabero I: un sitio precerámico de la localidad Angostura II, San José del Guaviare

Directory of Open Access Journals (Sweden)

Correal Gonzalo

1990-09-01

Full Text Available Archaeological excavation at the Guayabero I rock-shelter, considered the first stratified investigation of the preceramic period in the Colombian Amazonia, reveals human presence since c. a. 7000 B.P.  in the region. The Abrian type prismatic, concoid, triangular and retouched flakes, and the less abundant, terminal, disk-like, lateral and circular scrapers recovered from a brownish sandy soil are evidence of a preceramic occupation between 5000 and 2000 B.P. Scarce ceramic fragments found at the uppermost levels of the excavation, due to their similarity, only suggest possible relationships to ceramic traditions of the Araracuara and La Pedrera localities, within the same Amazon region. Pollen, seeds, ochre, and resins analysis will probably expand this first evidence of hunter-gatherers in the eastern tropical lowlands of Colombia. La excavación arqueológica en el abrigo rocoso Guayabero I, considerada como la primera investigación estratificada de un sitio precerámico en la Amazonia Colombiana, registra la presencia del hombre prehistórico a partir de c.a. 7000 A.P. Las lascas prismáticas, concoidales, triangulares y retocadas; y en menor frecuencia los raspadores circulares, discoidales y laterales, todos instrumentos de tipo Abriense recuperados de una capa de suelo arenoso pardusco, son evidencia de una ocupación precerámica en el sitio entre el 5000 y 2000 A.P. La reducida muestra de fragmentos cerámicos encontrados en los niveles más superficiales de la excavación, por su similaridad, recuerda las tradiciones cerámicas encontradas en las localidades de Araracuara y La Pedrera (región Amazónica. Muestras de polen, y análisis de semillas, ocre y resinas ampliarán esta primera evidencia de cazadores -recolectores en la región tropical de la Amazonia Colombiana.

Pegasus International, Inc. coating removal systems

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-02-01

The Pegasus Coating Removal System (PCRS) was demonstrated at Florida International University (FIU) where it was being evaluated for efficiency and cost. In conjunction with the FIU testing demonstration, a human factors assessment was conducted to assess the hazards and associated safety and health issues of concern for workers utilizing this technology. The PCRS is a chemical paste that is applied to the surface using a brush, roller, or airless sprayer. After the type of PCRS, thickness, and dwell time have been determined, a laminated backed material is placed on top of the chemical paste to slow down the drying process and to provide a mechanism to strip-off the chemical. After the dwell time is reached, the chemical substrate can be removed. Scrapers may be used to break-loose the layers as necessary or to break-loose the layers that are not removed when the laminated paper is picked up. Residue may also be cleaned off of the surface with a damp sponge with an agitating motion, absorbent sponges, or a vacuum, as needed. The paint and removal agent is then placed in drums for disposal at a later time. During the assessment sampling was conducted for organic vapors and general observational techniques were conducted for ergonomics. Recommendations for improved worker safety and health during application and removal of the PCRS include: (1) work practices that reflect avoidance of exposure or reducing the risk of exposure; (2) assuring all PPE and equipment are compatible with the chemicals being used; (3) work practices that reduce the worker`s need to walk on the slippery surface caused by the chemical or the use of special anti-slip soles; (4) careful control of overspray (if a spray application is used); and (5) the use of ergonomically designed long-handled tools to apply and remove the chemical (to alleviate some of the ergonomic concerns).

Characterization of fieldstone for a provenance study of local building stones and artifacts

Science.gov (United States)

Goossens, M.; De Kock, T.; Dewanckele, J.; Boone, M.; De Boever, W.; Brabant, L.; Louwye, S.; De Ceukelaire, M.; Vanhaecke, F.; Cnudde, V.

2012-04-01

Fieldstone is a Belgian silicified sandstone speckled with glauconite. The hardness varies with the degree of silicification and its colour, which is usually greenish, can differ from bluish gray to orange depending on the degree of oxidation of the glauconite. Although recently discovered in the clayey interlayers, fieldstone mainly appears in the sandy units of the Eocene in Western Flanders (Belgium). It occurs as lenses and banks parallel to the stratification. From Roman times onwards, these were locally intensely cultivated as local building stones. Furthermore archeological evidence points out fieldstone was used in prehistoric times to make various artifacts like scrapers and jacks. The purpose of our study is to characterize fieldstone from the different known geographical and stratigraphical localities. Ambiguous stratigraphical classifications of fieldstone outcrops in the past have complicated previous studies of fieldstone. Therefore, we aim to provide clarity over its stratigraphical occurrence and deliver additional information about its formation. The ultimate goal is to trace back the origin of the fieldstone used in buildings and for archeological artifacts to a distinct locality. For the characterization of the fieldstone different techniques were used. Thin sections were examined by petrographical microscopy in order to study grain size, porosity, mineralogy, degree of silicification and in some samples microfossil content like silicified foraminifers. Porosity was determined with volumetric analysis and high resolution X-ray computer tomography. Attention towards the dinoflagellate content was given. This can provide information about the age and depositional environment of the silicified sands. In addition, it can act as a distinct feature that is characteristic for one locality or stratigraphic layer. A selected amount of samples were chemically analysed with Laser Ablation Inductively Coupled Plasma Mass Spectrometer in order to check if

Functional feeding groups of aquatic insect families in Latin America: a critical analysis and review of existing literature.

Science.gov (United States)

Ramírez, Alonso; Gutiérrez-Fonseca, Pablo E

2014-04-01

Aquatic macroinvertebrates are involved in numerous processes within aquatic ecosystems. They often have important effects on ecosystem processes such as primary production (via grazing), detritus breakdown, and nutrient mineralization and downstream spiraling. The functional feeding groups (FFG) classification was developed as a tool to facilitate the incorporation of macroinvertebrates in studies of aquatic ecosystems. This classification has the advantage of combining morphological characteristics (e.g., mouth part specialization) and behavioral mechanisms (e.g., way of feeding) used by macroinvertebrates when consuming resources. Although recent efforts have greatly advanced our ability to identify aquatic macroinvertebrates, there is limited information on FFG assignment. Furthermore, there has been some variation in the use of the FFG classification, in part due to an emphasis on using gut content analysis to assign FFG, which is more appropriate for assigning trophic guilds. Thus, the main goals of this study are to (1) provide an overview of the value of using the FFG classification, (2) make an initial attempt to summarize available information on FFG for aquatic insects in Latin America, and (3) provide general guidelines on how to assign organisms to their FFGs. FFGs are intended to reflect the potential effects of organisms in their ecosystems and the way they consume resources. Groups include scrapers that consume resources that grow attached to the substrate by removing them with their mouth parts; shredders that cut or chew pieces of living or dead plant material, including all plant parts like leaves and wood; collectors-gatherers that use modified mouth parts to sieve or collect small particles (aquatic insects in Latin America, with an initial assignment to FFGs. We recommended caution when assigning FFGs based on gut contents, as it can provide misleading information. Overall, FFG is a very useful tool to understand the role of aquatic

Culturing bone marrow cells with dexamethasone and ascorbic acid improves osteogenic cell sheet structure.

Science.gov (United States)

Akahane, M; Shimizu, T; Kira, T; Onishi, T; Uchihara, Y; Imamura, T; Tanaka, Y

2016-11-01

To assess the structure and extracellular matrix molecule expression of osteogenic cell sheets created via culture in medium with both dexamethasone (Dex) and ascorbic acid phosphate (AscP) compared either Dex or AscP alone. Osteogenic cell sheets were prepared by culturing rat bone marrow stromal cells in a minimal essential medium (MEM), MEM with AscP, MEM with Dex, and MEM with Dex and AscP (Dex/AscP). The cell number and messenger (m)RNA expression were assessed in vitro, and the appearance of the cell sheets was observed after mechanical retrieval using a scraper. β-tricalcium phosphate (β-TCP) was then wrapped with the cell sheets from the four different groups and subcutaneously implanted into rats. After mechanical retrieval, the osteogenic cell sheets from the MEM, MEM with AscP, and MEM with Dex groups appeared to be fragmented or incomplete structures. The cell sheets cultured with Dex/AscP remained intact after mechanical retrieval, without any identifiable tears. Culture with Dex/AscP increased the mRNA and protein expression of extracellular matrix proteins and cell number compared with those of the other three groups. More bridging bone formation was observed after transplantation of the β-TCP scaffold wrapped with cell sheets cultured with Dex/AscP, than in the other groups. These results suggest that culture with Dex/AscP improves the mechanical integrity of the osteogenic cell sheets, allowing retrieval of the confluent cells in a single cell sheet structure. This method may be beneficial when applied in cases of difficult tissue reconstruction, such as nonunion, bone defects, and osteonecrosis.Cite this article: M. Akahane, T. Shimizu, T. Kira, T. Onishi, Y. Uchihara, T. Imamura, Y. Tanaka. Culturing bone marrow cells with dexamethasone and ascorbic acid improves osteogenic cell sheet structure. Bone Joint Res 2016;5:569-576. DOI: 10.1302/2046-3758.511.BJR-2016-0013.R1. © 2016 Akahane et al.

Modulation of cardiac myocyte phenotype in vitro by the composition and orientation of the extracellular matrix.

Science.gov (United States)

Simpson, D G; Terracio, L; Terracio, M; Price, R L; Turner, D C; Borg, T K

1994-10-01

Cellular phenotype is the result of a dynamic interaction between a cell's intrinsic genetic program and the morphogenetic signals that serve to modulate the extent to which that program is expressed. In the present study we have examined how morphogenetic information might be stored in the extracellular matrix (ECM) and communicated to the neonatal heart cell (NHC) by the cardiac alpha 1 beta 1 integrin molecule. A thin film of type I collagen (T1C) was prepared with a defined orientation. This was achieved by applying T1C to the peripheral edge of a 100 mm culture dish. The T1C was then drawn across the surface of the dish in a continuous stroke with a sterile cell scraper and allowed to polymerize. When NHCs were cultured on this substrate, they spread, as a population, along a common axis in parallel with the gel lattice and expressed an in vivo-like phenotype. Individual NHCs displayed an elongated, rod-like shape and disclosed parallel arrays of myofibrils. These phenotypic characteristics were maintained for at least 4 weeks in primary culture. The evolution of this tissue-like organizational pattern was dependent upon specific interactions between the NHCs and the collagen-based matrix that were mediated by the cardiac alpha 1 beta 1 integrin complex. This conclusion was supported by a variety of experimental results. Altering the tertiary structure of the matrix or blocking the extracellular domains of either the cardiac alpha 1 or beta 1 integrin chain inhibited the expression of the tissue-like pattern of organization. Neither cell-to-cell contact or contractile function were necessary to induce the formation of the rod-like cell shape. However, beating activity was necessary for the assembly of a well-differentiated myofibrillar apparatus. These data suggest that the cardiac alpha 1 beta 1 integrin complex serves to detect and transduce phenotypic information stored within the tertiary structure of the surrounding matrix.

Recent advances in stellarator optimization

Science.gov (United States)

Gates, D. A.; Boozer, A. H.; Brown, T.; Breslau, J.; Curreli, D.; Landreman, M.; Lazerson, S. A.; Lore, J.; Mynick, H.; Neilson, G. H.; Pomphrey, N.; Xanthopoulos, P.; Zolfaghari, A.

2017-12-01

discussed. A new algorithm developed for the design of the scraper element on W7-X is presented along with ideas for automating the optimization approach.

High Heat flux (HHF) elements for Negative Ion Systems on ITER

International Nuclear Information System (INIS)

Milnes, J.; Chuilon, B.; Martin, D.; Waldon, Ch.; Yong Xue

2006-01-01

Negative Ion Neutral Beam systems on ITER will require actively cooled scrapers and dumps to process and shape the beam before injection into the tokamak. The scale of the systems is much larger than any presently operating, bringing challenges for designers in terms of available sub cooling, total pressure drop, deflection and mandatory remote maintenance. In common with Positive Ion systems, flux densities in the order of 15-20 MW/m 2 are commonplace but with much longer pulses. A pulse length in excess of 3000 seconds and the anticipated beam breakdown rate pose new challenges in terms of stress and fatigue life. The cooling system specification (up to 26 bar, 80 o C) adds further constraints impacting the material choice and operating temperature. The DDD designs, based on swirl tubes, have been reviewed as part of the design process and recommendations made. Additionally, alternative designs have been proposed based on the Hypervapotron high heat flux elements with modified geometry and drawing upon a vast background knowledge of large scale equipment procurement and integration. Existing operational and design experience has been applied to give a simple, robust and low maintenance alternative. A full thermomechanical analysis of all HHF components has been undertaken based on ITER design criteria and the limited material data available. The results of this analysis will be presented, highlighting areas where further R(and)D is necessary to reach the operating limits set out in the functional specification. Extensive comparison of these analyses is made with the large operational database of existing JET beamline components for benchmarking purposes. A particular feature of the thermo-mechanical analyses is a fully self-consistent description in which ageing characteristics are related to the local temperature, and the components' power loading takes into account the thermal distortion. The advantages and disadvantages of all designs will be presented and

Knowledge, conservation and sustainable use of soil: physic and morphological aspects

Directory of Open Access Journals (Sweden)

Marcello Pagliai

2009-10-01

Full Text Available The main aspects of environmental degradation can be ascribed to soil (erosion, soil compaction, soil crusting, deterioration of soil structure, flooding, losses of organic matter, salinisation, onsite and offsite damages, etc. following the impact of human activities. Since agricultural conventional production systems have resulted in excessive erosion and soil degradation, there is need to control and fight such degradation. Scientific results have clearly showed that the agricultural management systems can play an important role in preventing soil degradation provide that appropriate management practices are adopted. Long-term field experiments in different types of soils have shown that alternative tillage systems, like minimum tillage, ripper subsoiling, etc., improve the soil structural quality. The continuous conventional tillage causes a decrease of soil organic matter content that is associated to a decrease of aggregate stability, leading, as a consequence, to the formation of surface crusts, with an increase of runoff and erosion risks. Other aspects of very dangerous soil degradation (erosion in the hilly environments are represented by land levelling and scraping. After levelling, slopes being prepared for plantation (in particularly vineyard are almost always characterised by the presence of large amounts of incoherent earth materials accumulated with scraper. In this vulnerable condition, a few summer storms can easily cause soil losses exceeding 500 Mg ha-1y-1. Moreover, the land levelling and the following soil loss causes drastic alteration of the landscape and loss of the cultural value of soil. Subsoil compaction is strongly under evaluated, even though the presence of a ploughpan at the lower limit of cultivation is largely widespread in the alluvial soils of the plains cultivated by monoculture and it is responsible of the frequent flooding of such plains in occasion of heavy rains concentrated in a short time (rainstorm

The role of burrowing sponges in bioerosion.

Science.gov (United States)

Rützler, Klaus

1975-09-01

scrapers. The former are intermittent and their activities are affected by environmental and biological interactions, while activities of the latter are rather constant and guided by the need for food.

Monte Carlo dose calculation improvements for low energy electron beams using eMC

International Nuclear Information System (INIS)

Fix, Michael K; Frei, Daniel; Volken, Werner; Born, Ernst J; Manser, Peter; Neuenschwander, Hans

2010-01-01

The electron Monte Carlo (eMC) dose calculation algorithm in Eclipse (Varian Medical Systems) is based on the macro MC method and is able to predict dose distributions for high energy electron beams with high accuracy. However, there are limitations for low energy electron beams. This work aims to improve the accuracy of the dose calculation using eMC for 4 and 6 MeV electron beams of Varian linear accelerators. Improvements implemented into the eMC include (1) improved determination of the initial electron energy spectrum by increased resolution of mono-energetic depth dose curves used during beam configuration; (2) inclusion of all the scrapers of the applicator in the beam model; (3) reduction of the maximum size of the sphere to be selected within the macro MC transport when the energy of the incident electron is below certain thresholds. The impact of these changes in eMC is investigated by comparing calculated dose distributions for 4 and 6 MeV electron beams at source to surface distance (SSD) of 100 and 110 cm with applicators ranging from 6 x 6 to 25 x 25 cm 2 of a Varian Clinac 2300C/D with the corresponding measurements. Dose differences between calculated and measured absolute depth dose curves are reduced from 6% to less than 1.5% for both energies and all applicators considered at SSD of 100 cm. Using the original eMC implementation, absolute dose profiles at depths of 1 cm, d max and R50 in water lead to dose differences of up to 8% for applicators larger than 15 x 15 cm 2 at SSD 100 cm. Those differences are now reduced to less than 2% for all dose profiles investigated when the improved version of eMC is used. At SSD of 110 cm the dose difference for the original eMC version is even more pronounced and can be larger than 10%. Those differences are reduced to within 2% or 2 mm with the improved version of eMC. In this work several enhancements were made in the eMC algorithm leading to significant improvements in the accuracy of the dose calculation

Monte Carlo dose calculation improvements for low energy electron beams using eMC.

Science.gov (United States)

Fix, Michael K; Frei, Daniel; Volken, Werner; Neuenschwander, Hans; Born, Ernst J; Manser, Peter

2010-08-21

The electron Monte Carlo (eMC) dose calculation algorithm in Eclipse (Varian Medical Systems) is based on the macro MC method and is able to predict dose distributions for high energy electron beams with high accuracy. However, there are limitations for low energy electron beams. This work aims to improve the accuracy of the dose calculation using eMC for 4 and 6 MeV electron beams of Varian linear accelerators. Improvements implemented into the eMC include (1) improved determination of the initial electron energy spectrum by increased resolution of mono-energetic depth dose curves used during beam configuration; (2) inclusion of all the scrapers of the applicator in the beam model; (3) reduction of the maximum size of the sphere to be selected within the macro MC transport when the energy of the incident electron is below certain thresholds. The impact of these changes in eMC is investigated by comparing calculated dose distributions for 4 and 6 MeV electron beams at source to surface distance (SSD) of 100 and 110 cm with applicators ranging from 6 x 6 to 25 x 25 cm(2) of a Varian Clinac 2300C/D with the corresponding measurements. Dose differences between calculated and measured absolute depth dose curves are reduced from 6% to less than 1.5% for both energies and all applicators considered at SSD of 100 cm. Using the original eMC implementation, absolute dose profiles at depths of 1 cm, d(max) and R50 in water lead to dose differences of up to 8% for applicators larger than 15 x 15 cm(2) at SSD 100 cm. Those differences are now reduced to less than 2% for all dose profiles investigated when the improved version of eMC is used. At SSD of 110 cm the dose difference for the original eMC version is even more pronounced and can be larger than 10%. Those differences are reduced to within 2% or 2 mm with the improved version of eMC. In this work several enhancements were made in the eMC algorithm leading to significant improvements in the accuracy of the dose

PRACTICAL PROPOSALS AS A RESULT OF THEORETICAL AND EXPERIMENTAL STUDIES OF THE PROCESS OF EXTRACTION FROM RAW MATERIALS OF PLANT ORIGIN

Directory of Open Access Journals (Sweden)

I. I. Shishatskii

2014-01-01

Full Text Available Summary. Theoretical and experimental researches of extraction processes from plant origin raw materials: barley, acorns and chicory with liquid carbon dioxide, as well as lupin with cheese whey were carried out. Quality indicators of extracts and secondary raw materials are defined. It is established that they are perspective raw sources for the enriched and functional products as they contain amino acids, vitamins and microelements. The dairy-vegetative lupine extract, for example, contains 17 amino acids, including the essential as well as vitamins and minerals. The studies of secondary raw materials, barley, acorns, chicory and lupine quality showed the expediency of their use for foods enrichment. Quality indicators of secondary raw materials are presented in the tables form in the given work. It formed the basis for the development of hardware-technological schemes of obtaining СО2-extracts and their use. The hardware-technological scheme of obtaining СО2-extracts from barley, acorns and chicory includes a number of equipment units: motor transport for raw materials delivery to the enterprise, the scraper hydroconveyor, the jet washer, a photoseparator for of poor-quality raw materials and impurities removal, a blowing machine for removing surface moisture from the raw materials, a jet washer for peeling, a cutter, drying and frying device, a crusher, a roller machine tool and an extracting unit. Hardware providing for yoghurt technology enriched with amino acids, microelements and vitamins which are present in a dairy-plant extract differs from the mentioned above one in the following. The extract used is a cheese whey, and the extraction of a target component is carried out in a vibrating extractor. The hardwaretechnological scheme is made according to Russian technology of yoghurt and furnished with the equipment for dairy-vegetative extract feeding into a product. It includes the following: a vibrating extractor (not shown in fig

Relleno de cavidades óseas en cirugía maxilofacial con materiales autólogos Bone cavity augmentation in maxillofacial surgery using autologous material

Directory of Open Access Journals (Sweden)

P. Infante-Cossío

2007-02-01

Full Text Available Aunque se han descrito numerosos materiales para rellenar una cavidad ósea, el mejor material sigue siendo el hueso autólogo corticoesponjoso o particulado, que puede formar hueso nuevo por mecanismos de osteogénesis, osteinducción y osteoconducción. El cirujano oral y maxilofacial debe conocer las propiedades biológicas y las características fundamentales de los materiales autólogos, las diferentes técnicas de obtención y sus aplicaciones clínicas. Como zonas donantes se emplean preferentemente las intraorales, el filtro de hueso y los raspadores para pequeños defectos, y el hueso ilíaco, tibia o calota cuando se requiere más cantidad. No existen estudios concluyentes respecto a la asociación de injertos óseos con membranas. La combinación de injertos autólogos con otros materiales de relleno, ha desembocado en múltiples estudios, sin que se puedan establecer conclusiones definitivas por el momento. El hueso autólogo es de elección para el relleno de cavidades óseas, ya que es útil para dar solución a variadas situaciones clínicas de forma simple, rápida y segura.Although a large number of materials have been described for augmenting bone cavities, the best material is still autologous cortical-cancellous bone or bone chip, which can form new bone through osteogenesis, osteoinduction and osteoconduct ion mechanisms. The oral and maxillofacial surgeon needs to be familiar with the biological properties and the fundamental characteristics of autologous material, the different techniques for obtaining it and its clinical application. Donor sites should preferably be intraoral. Bone filters and scrapers should be used for small defects, and the iliac, tibial or calvaria bones [should be used] when more quantity is required. There are no conclusive studies with regard to combining bone grafts with membranes. The combination of autologous grafts with other augmentation material has led to multiple studies, although

Influence of dietary carbon on mercury bioaccumulation in streams of the Adirondack Mountains of New York and the Coastal Plain of South Carolina, USA

Science.gov (United States)

Riva-Murray, Karen; Bradley, Paul M.; Chasar, Lia C.; Button, Daniel T.; Brigham, Mark E.; Eikenberry, Barbara C. Scudder; Journey, Celeste A.; Lutz, Michelle A.

2013-01-01

We studied lower food webs in streams of two mercury-sensitive regions to determine whether variations in consumer foraging strategy and resultant dietary carbon signatures accounted for observed within-site and among-site variations in consumer mercury concentration. We collected macroinvertebrates (primary consumers and predators) and selected forage fishes from three sites in the Adirondack Mountains of New York, and three sites in the Coastal Plain of South Carolina, for analysis of mercury (Hg) and stable isotopes of carbon (δ13C) and nitrogen (δ15N). Among primary consumers, scrapers and filterers had higher MeHg and more depleted δ13C than shredders from the same site. Variation in δ13C accounted for up to 34 % of within-site variation in MeHg among primary consumers, beyond that explained by δ15N, an indicator of trophic position. Consumer δ13C accounted for 10 % of the variation in Hg among predatory macroinvertebrates and forage fishes across these six sites, after accounting for environmental aqueous methylmercury (MeHg, 5 % of variation) and base-N adjusted consumer trophic position (Δδ15N, 22 % of variation). The δ13C spatial pattern within consumer taxa groups corresponded to differences in benthic habitat shading among sites. Consumers from relatively more-shaded sites had more enriched δ13C that was more similar to typical detrital δ13C, while those from the relatively more-open sites had more depleted δ13C. Although we could not clearly attribute these differences strictly to differences in assimilation of carbon from terrestrial or in-channel sources, greater potential for benthic primary production at more open sites might play a role. We found significant variation among consumers within and among sites in carbon source; this may be related to within-site differences in diet and foraging habitat, and to among-site differences in environmental conditions that influence primary production. These observations suggest that different

Construction of clay sealings for dumping of brown coal ash and residues from gas desulfurization units. Herstellung von Tonabdichtungen zur Deponierung von Braunkohleaschen und REA-Rueckstaenden

Energy Technology Data Exchange (ETDEWEB)

Kortmann, W

1989-07-01

With the putting into operation of flue gas scrubbers at the brown coal-fired power stations of the RWE not only 5 to 6 Mt conventional power station ash but also up to 2 Mt gypsum and water from the flue gas desulphurisation units are obtained annually, and these residues together with the ash are tipped on mixed dumps. These dumps are enclosed on all sides by a mineral sealing of clay with a thickness of at least 0.6 m. In keeping with the detailed plans for the construction and operation of mixed dumps as submitted to the competent authorities for approval, the sealing must have a permeability of K < 5x10{sup -10} m/s for the dump base and of K < 1x10{sup -10} m/s for the cover of the dump. In order to meet these high quality requirements the clay, which is obtained by opencast working with the aid of bucket wheel excavators, must first of all be crushed for construction of the sealings. In addition to the crushing of the clay to as small a lump size as possible, the adjustment of the correct sealing moisture content of the clay is of primary importance. Conditioning of the clay is effected in the conventional way by means of a pulvimixer, but also by means of a processing plant in pilot operation in the construction of clay sealings for dumps. With the aid of the processing plant clay of a high homogenisation grade is constantly available for sealing construction. The clay is spread on the base and slopes of the dump layer by layer with the aid of scraper dozers, each layer having a compacted thickness of about 20 cm. Compaction of the sealing layers is effected by heavy rammer butt rollers. In the case of highly plastic earth materials of the type used here in the construction of dumps the weight of the compacting roller and also the shape of the rammer butt are of importance. Compaction in the 1:2.5 steep dump slopes by means of a detachable roller steered by a cable has proved very satisfactory.

Developments in mechanization of operations of comprehensively mechanized longwalls in the USSR and abroad. Sovershenstvovanie sredstv mekhanizatsii kontsevykh operatsii v kompleksno-mekhanizirovannykh lavakh v SSSR i za rubezhom

Energy Technology Data Exchange (ETDEWEB)

Bodrunov, L D

1985-01-01

This paper discusses construction and introduction of equipment for mining at junctions of longwalls and roadways. Design and operation of a Soviet made narrow web shearer loader with chainless advance, enabling coal extraction by side cutting without the provision of stables in seams 2-4.1 m thick and up to 30 degrees inclination are described along with two types (520 mm and 630 mm high) of narrow web shearer loaders for extracting 0.7-0.95 m and 0.8-1.2 m thick seams with inclinations up to 35 degrees. Three types of machines constructed to operate in thin seams are presented. They are designed to extract coal from seams: 0.6-1.3 m thick with shear strength of 2.5 kN/cm, 0.65-1.2 m thick with shear strength up to 3.0 kN/cm and seams 0.8-1.8 m thick also with 3.0 kN/sm shear strength. Stableless extraction is also possible due to developments which have taken place in face scraper conveyors with shortened driving heads. Some of the new conveyors can be used in normal complexes to extract flat and inclined seams 1-2.5 m thick, whilst others are used to extract flat and inclined thin seams (0.7-1.2 m). The use of two shearer loaders has resulted in reduction in stable size or stableless extraction. Mechanization of supports at junctions of longwalls and mine roadways by means of metal supporting beams in conjunction with hydraulic or friction props is described. Mechanization of similar operations in foreign mines is also described, e.g. stableless extraction in the UK, where up to 80% of coal is extracted by the longwall system and 20% by the pillar system using the two shearer loader method. Machines produced by Anderson Strathclyde, Mining Supplies, and British Jeffrey Diamond and props manufactured by Dowty and Gullick Dobson are described. FRG coal extraction is carried out chiefly (95%) from inclined seams more than 4 m thick, using a pillar mining system (25%), longwall system (58%) and combined (17%).

Hydrological cycle effects on the aquatic community in a Neotropical stream of the Andean piedmont during the 2007-2010 ENSO events.

Science.gov (United States)

Ríos-Pulgarín, M I; Barletta, M; Mancera-Rodriguez, N J

2016-07-01

The seasonal and interannual changes in the fish, macroinvertebrates and phycoperiphyton assemblages of the Guarinó River were examined in relation to the physical and chemical environmental changes associated with the hydrological cycle and the El Niño-Niña/Southern Oscillation (ENSO) between 2007 and 2010. Four samplings (in dry and rainy seasons) were performed per year. Environmental variables (temperature, pH, conductivity, turbidity, oxygen, total nitrogen, orthophosphate, depth and flow rate) were measured. The temporal patterns of the taxonomic compositions for the three assemblages and the functional composition of fish and macroinvertebrate assemblages with respect to environmental variables were examined through canonical discriminant analysis, multidimensional scaling and multiple correlations. The presence and abundance of fishes, macroinvertebrates and algae species were regulated by environmental variables associated with extreme hydrological events, which derived from the natural torrential regimen of the basin and larger-scale phenomena, such as El Niño and La Niña. Fish abundance and richness were significantly correlated with algal density and pH, the macroinvertebrate density was negatively related to the flow rate and the richness was positively correlated with algal density. The algae richness was positively correlated with pH and negatively correlated with the flow rate and nitrogen. The algal density was positively correlated with pH and temperature and negatively correlated with river flow. The phycoperiphyton assemblage exhibited more direct responses in its density and richness to the hydrological changes (r(2) = 0·743 and 0·800, respectively). In functional terms, the El Niño phenomenon was defined by a greater abundance of omnivorous and insectivorous fishes, as well as filter feeders, scrapers and macroinvertebrate predators. During La Niña, a greater abundance of benthic fishes (both detritivorous and insectivorous) and

Gravel road stabilisation of Ehnsjoevaegen, Hallstavik[Using fly ash]; Skogsbilvaegsrenovering av Ehnsjoevaegen, Hallstavik

Energy Technology Data Exchange (ETDEWEB)

Macsik, Josef; Svedberg, Bo [Ecoloop, Stockholm (Sweden)

2006-03-15

Fly ash in geotechnical applications has stabilising, isolating, low permeability and hardening effect. Fly ash can be used in road constructions with low bearing capacity, as well as on top cover material on landfills. The aim of the project was to build a road section with fly ash stabilised gravel, based on laboratory studies, and follow up technical and environmental aspect during the first year after stabilisation. The overall aim of this project was to evaluate fly ash from Holmen Paper, Hallstavik, from technical and environmental point of view in a gravel road construction. A gravel road, Ehnsjoevaegen, was stabilised with fly ash during autumn 2004. This road was a low priority road. The fly ash stabilised road section was 1300 m long. Gravel from the road Ehnsjoevaegen was stabilised and investigated in a laboratory study. Leachability of metals and geotechnical aspects were investigated. The laboratory study showed that fly ash stabilised gravel has high shear strength, however its thawing resistance is not fully acceptable. Additives of cement or merit are needed in order to increase its thawing resistance. The actual road section is not going to be used during thawing period and no additives were used. The test road is divided into different sections including a reference section. The road stabilisation work was conducted with gravel transported to Ehnsjoevaegen from off site and not with gravel from the site. Fly ash was tipped off on a levelled road, followed by tipping of gravel. Mixing fly ash and gravel was done on site by a road scraper. After the mixing the road was gravelled with 0,1 m graded gravel. In this project the fly ash had low water content. In order to get optimal compaction water was added from a tanker supplying water before compacted with a compactor. Results from the pilot test shows that fly ash stabilised gravel can be tipped, mixed and compacted effectively. Tipping can be optimised if fly ash and gravel is mixed in a mixer

Lipopolysaccharide Binding Protein Enables Intestinal Epithelial Restitution Despite Lipopolysaccharide Exposure

Science.gov (United States)

Richter, Juli M.; Schanbacher, Brandon L.; Huang, Hong; Xue, Jianjing; Bauer, John A.; Giannone, Peter J.

2011-01-01

Intestinal epithelial restitution is the first part in the process of mucosal repair after injury in the intestine. Integrity of the intestinal mucosal barrier is important as a first line of defense against bacteria and endotoxin. Necrotizing enterocolitis (NEC) is a major cause of morbidity and mortality in extremely low birth weight infants, but its mechanisms are not well defined. Abnormal bacterial colonization, immature barrier function, innate immunity activation and inflammation likely play a role. Lipopolysaccharide (LPS) binding protein (LBP) is secreted by enterocytes in response to inflammatory stimuli and has concentration-dependent effects. At basal concentrations, LBP stimulates the inflammatory response by presenting LPS to its receptor. However, at high concentrations, LBP is able to neutralize LPS and prevent an exaggerated inflammatory response. We sought to determine how LBP would affect wound healing in an in vitro model of intestinal cell restitution and protect against intestinal injury in a rodent model of NEC. Immature intestinal epithelial cells (IEC-6) were seeded in poly-l-lysine coated 8 chamber slides and grown to confluence. A 500μm wound was created using a cell scraper mounted on the microscope to achieve uniform wounding. Media was replaced with media containing LPS +/− LBP. Slide wells were imaged after 0, 8, and 24 hours and then fixed. Cellular restitution was evaluated via digital images captured on an inverted microscope and wound closure was determined by automated analysis. TLR4 was determined by rtPCR after RNA isolation from wounded cells 24 hours after treatment. LPS alone attenuated wound healing in immature intestinal epithelium. This attenuation is reversed by 24 hours with increasing concentrations of LBP so that wound healing is equivalent to control (p< 0.001). TLR4 was increased with LPS alone but levels returned to that of control after addition of LBP in the higher concentrations. LBP had no effect on the

Guanaco traces and hunting strategies at Alto Patache North Chilean fog oasis

Science.gov (United States)

Larrain, H.; Cereceda, P.; Pérez, L.

2010-07-01

1. In foregoing Fog Conferences, some of us have made explicit the rich botanic and faunistic inventory to be found at this Chilean Fog site. This was specially apparent under strong ENSO conditions, as it happened in 1997/98 in the area. Among the mammal biggest species represented, the guanaco (Lama guanicoe Müller) merits special mention. Clear traces of their presence and eventual hunting and slaughtering by primitive populations have survived until present times. Among them, the myriads of guanaco trails still covering practically all the slopes along the foggy area, close to the sea, and their wollowing and defecating places are found. Also, although less studied, plant eating traces left behind by roaming camelids can be seen. 2. Guanaco hunting traces still visible at Alto Patache can be portrayed differently through : A) Analysis of lithic artifacts used as arms in hunting operations; B) Botanic response to animal attack; C) Examination of topographic traits used by primitive man in guanaco hunting strategies. A. Hundreds of lithic instruments made of stone, were abandoned by hunters in situ, some of them were intact, some fragmented, which would demonstrate a direct relationship with hunting and slaughtering, and also their elaboration in workshops at place. Lithic points, scrapers and knives were found at places specially apt for hunting or slaughtering activities. Total isolation of the mountain fog site previous to our arrival in 1996, favoured their conservation at place. B. Careful observation of some local plants showed clear traces of guanaco feeding habits. As a proof thereof, old cactus of the species Eulychnia iquiquensis show in their basal portions clear signals in the forms of scars, caused by the eating by guanacos. Guanaco faeces were found at the foot of Ephedra plants. Many dead Stipa ichu plants (Gramineae), in different areas of the oasis provide evidence of cutting close to their basis, caused by sharp guanaco tooth under severe food

Functional feeding groups of aquatic insect families in Latin America: a critical analysis and review of existing literature

Directory of Open Access Journals (Sweden)

Alonso Ramírez

2014-04-01

Full Text Available Aquatic macroinvertebrates are involved in numerous processes within aquatic ecosystems. They often have important effects on ecosystem processes such as primary production (via grazing, detritus breakdown, and nutrient mineralization and downstream spiraling. The functional feeding groups (FFG classification was developed as a tool to facilitate the incorporation of macroinvertebrates in studies of aquatic ecosystems. This classification has the advantage of combining morphological characteristics (e.g., mouth part specialization and behavioral mechanisms (e.g., way of feeding used by macroinvertebrates when consuming resources. Although recent efforts have greatly advanced our ability to identify aquatic macroinvertebrates, there is limited information on FFG assignment. Furthermore, there has been some variation in the use of the FFG classification, in part due to an emphasis on using gut content analysis to assign FFG, which is more appropriate for assigning trophic guilds. Thus, the main goals of this study are to (1 provide an overview of the value of using the FFG classification, (2 make an initial attempt to summarize available information on FFG for aquatic insects in Latin America, and (3 provide general guidelines on how to assign organisms to their FFGs. FFGs are intended to reflect the potential effects of organisms in their ecosystems and the way they consume resources. Groups include scrapers that consume resources that grow attached to the substrate by removing them with their mouth parts; shredders that cut or chew pieces of living or dead plant material, including all plant parts like leaves and wood; collectors-gatherers that use modified mouth parts to sieve or collect small particles (<1mm accumulated on the stream bottom; filterers that have special adaptations to remove particles directly from the water column; and predators that consume other organisms using different strategies to capture them. In addition, we provide

Spatial scales of carbon flow in a river food web

Science.gov (United States)

Finlay, J.C.; Khandwala, S.; Power, M.E.

2002-01-01

Spatial extents of food webs that support stream and river consumers are largely unknown, but such information is essential for basic understanding and management of lotic ecosystems. We used predictable variation in algal ??13C with water velocity, and measurements of consumer ??13C and ??15N to examine carbon flow and trophic structure in food webs of the South Fork Eel River in Northern California. Analyses of ??13C showed that the most abundant macroinvertebrate groups (collector-gatherers and scrapers) relied on algae from local sources within their riffle or shallow pool habitats. In contrast, filter-feeding invertebrates in riffles relied in part on algal production derived from upstream shallow pools. Riffle invertebrate predators also relied in part on consumers of pool-derived algal carbon. One abundant taxon drifting from shallow pools and riffles (baetid mayflies) relied on algal production derived from the habitats from which they dispersed. The trophic linkage from pool algae to riffle invertebrate predators was thus mediated through either predation on pool herbivores dispersing into riffles, or on filter feeders. Algal production in shallow pool habitats dominated the resource base of vertebrate predators in all habitats at the end of the summer. We could not distinguish between the trophic roles of riffle algae and terrestrial detritus, but both carbon sources appeared to play minor roles for vertebrate consumers. In shallow pools, small vertebrates, including three-spined stickleback (Gasterosteus aculeatus), roach (Hesperoleucas symmetricus), and rough-skinned newts (Taricha granulosa), relied on invertebrate prey derived from local pool habitats. During the most productive summer period, growth of all size classes of steelhead and resident rainbow trout (Oncorhynchus mykiss) in all habitats (shallow pools, riffles, and deep unproductive pools) was largely derived from algal production in shallow pools. Preliminary data suggest that the strong

Metals from the ritual site of Shaitanskoye Ozero II (Sverdlovsk Oblast, Russia

Directory of Open Access Journals (Sweden)

Nikolaevna Korochkova, Olga

2010-12-01

Full Text Available The present article describes materials from the ritual site of Shaitanskoye Ozero II, Sverdlovsk Oblast. Few excavations carried out at the site measuring less than 240 sq. m in size, yielded more than 160 bronze artifacts: utensils, weapons, rolled copper ornaments, and abundant smelting and casting waste. Apart from Seima-Turbino (celts and laminar knives and Eurasian types (daggers with cast hilts, truncated knives with guards, fluted bracelets and rings, several metal artifacts were revealed manufactured in the style of the Samus-Kizhirovo tradition. Bronze artifacts, stone knives and scrapers, and numerous arrowheads are accompanied by ceramics of the Koptyaki type. Metals use mainly a copper-tin alloy. This assemblage is shown to be relevant to the local tradition of metalworking, which, in this particular region, was comparatively ancient having been left uninterrupted by the rapid migrations of the Seima-Turbino people. In addition, the assemblage indicates the sources from which post-Seima artifacts reached the Alakul people. These artifacts may also have been linked with a large metalworking center located in the Middle Urals.

Este artículo describe los materiales del sitio ritual de Shaitanskoye Ozero II, Provincia de Sverdlovsk. Las reducidas excavaciones emprendidas en el lugar con superficie inferior a los 240 m² han entregado más de 160 objetos de bronce: utensilios, armas, adornos en espiral de cobre y abundantes residuos de la fusión y el trabajo del metal. Además de tipos Seima-Turbino (hachas tubulares y cuchillos planos y Euroasiáticos (puñales de mango fundido, cuchillos con empuñadura de lengüeta, brazaletes y anillos acanalados, varios artefactos metálicos resultaron manufacturados según el estilo de la tradición Samus-Kizhirovo. Los artefactos de bronce, los líticos (cuchillos, raspadores y numerosas puntas de flecha están acompañados por cerámicos de tipo Koptyaki. El metal es

Daily and seasonal trends of electricity and water use on pasture-based automatic milking dairy farms.

Science.gov (United States)

Shortall, J; O'Brien, B; Sleator, R D; Upton, J

2018-02-01

The objective of this study was to identify the major electricity and water-consuming components of a pasture-based automatic milking (AM) system and to establish the daily and seasonal consumption trends. Electricity and water meters were installed on 7 seasonal calving pasture-based AM farms across Ireland. Electricity-consuming processes and equipment that were metered for consumption included milk cooling components, air compressors, AM unit(s), auxiliary water heaters, water pumps, lights, sockets, automatic manure scrapers, and so on. On-farm direct water-consuming processes and equipment were metered and included AM unit(s), auxiliary water heaters, tubular coolers, wash-down water pumps, livestock drinking water supply, and miscellaneous water taps. Data were collected and analyzed for the 12-mo period of 2015. The average AM farm examined had 114 cows, milking with 1.85 robots, performing a total of 105 milkings/AM unit per day. Total electricity consumption and costs were 62.6 Wh/L of milk produced and 0.91 cents/L, respectively. Milking (vacuum and milk pumping, within-AM unit water heating) had the largest electrical consumption at 33%, followed by air compressing (26%), milk cooling (18%), auxiliary water heating (8%), water pumping (4%), and other electricity-consuming processes (11%). Electricity costs followed a similar trend to that of consumption, with the milking process and water pumping accounting for the highest and lowest cost, respectively. The pattern of daily electricity consumption was similar across the lactation periods, with peak consumption occurring at 0100, 0800, and between 1300 and 1600 h. The trends in seasonal electricity consumption followed the seasonal milk production curve. Total water consumption was 3.7 L of water/L of milk produced. Water consumption associated with the dairy herd at the milking shed represented 42% of total water consumed on the farm. Daily water consumption trends indicated consumption to be lowest in

THE CONCEPTUAL FRAMEWORK OF FORMING THE PRODUCT QUALITY CONTROL STRATEGY OF ROAD-BUILDING ENGINEERING ENTERPRISES

Directory of Open Access Journals (Sweden)

Mariia Sadova

2017-11-01

of roads is impossible without the organization of effective operation of the road for mechanical engineering – heavy construction and earthmoving machinery. Currently in our country present its own engineering manufacturers of road construction equipment (among large – JSC "Kredmash", however, the domestic production of road is significantly inferior in terms of domestic consumption of products of foreign manufacturers of the road. Despite the fact that the price of domestic producers less than of imported ones an average in three times, including bulldozers, scrapers, cranes, crawler cars more than 50% (Komatsu, Hitachi, Mitsubishi and others.. Practical implications. The practical significance of the results of the study identifies opportunities to improve the efficiency of traffic control products quality enterprises construction and road engineering. Value/originality. Implementation of the proposed methods and approaches to the formation of the quality of the machine-building enterprise management strategy for road construction will improve the efficiency of quality control processes and the level of enterprise competitiveness.

Temporal variations in the diet of the exotic rainbow trout (Oncorhynchus mykiss in an Andean-Patagonian canopied stream Variación temporal en la dieta de la trucha exótica arco iris (Oncorhynchus mykiss en un arroyo forestado de los Andes patagónicos

Directory of Open Access Journals (Sweden)

LEONARDO M BURIA

2009-03-01

Full Text Available We examined seasonal and diel variation in prey species composition and biomass in the diet of the exotic rainbow trout Oncorhynchus mykiss (Walbaum, 1972. The study was carried out in the upper-forested sections of a low order stream in Andean-Patagonia. We studied the importance of functional feeding groups of aquatic invertebrates and the relative contribution of terrestrial and aquatic prey items in order to assess the pathways connecting terrestrial and aquatic ecosystems along a stream food web. Trout fed on approximately 40 invertebrate species and scrapers were consistently selected, suggesting their increased vulnerability to predation. However in terms of biomass, rainbow trout diet was mostly composed by shredders which emphasized the role of the allochthonous plant detritus pathway in food webs of forested small streams. Trout individuals fed more intensively in spring and summer and during daytime. Terrestrial items constituted a minor proportion of the diet implying that this component did not represent a significant subsidy for this fish population. As a consequence, the top-down effect on the aquatic community does not appear to be dampened since trout do not strongly preyed on terrestrial invertebrates.Se estudió la variación estacional y diaria en la composición y biomasa de las especies presa en la dieta de la exótica trucha arco iris Oncorhynchus mykiss (Walbaum, 1972 en la sección superior de un arroyo boscoso de bajo orden en los Andes patagónicos. Se analizó la importancia de los grupos funcionales alimentarios de invertebrados acuáticos y la contribución relativa de las presas de origen terrestre y acuático para evaluar las vías tróficas que conectan los ecosistemas acuático y terrestre circundantes. Las truchas consumieron aproximadamente unas 40 especies de invertebrados y los raspadores fueron consistentemente seleccionados, sugiriendo una alta vulnerabilidad a la depredación. Sin embargo en términos de

Enhancing the safety and efficiency of the driving gear of coal mining machinery by using water as a hydraulic fluid and enhancing the reliability of scraper-chain conveyors; Erhoehung der Sicherheit und Leistungsfaehigkeit der Antriebstechnik von Arbeitsmaschinen durch Verwendung von Wasserhydraulik sowie Erhoehung der Zuverlaessigkeit der Kettenkratzerfoerderer

Energy Technology Data Exchange (ETDEWEB)

Reichel, J.; Boeing, R.; Graetz, A.; Loehning, H.D.; Plum, D.

1997-12-31

The objective pursued is to increasingly use water or high water-content fluids as a substitute for other hydraulic fluids in driving gear of mining machinery. The state of the art of the technology is represented only by individual solutions achieved for given purposes which are not suitable for other applications, let alone for coal mining machinery. The research project was to identify hydraulic components that will permit the use of water or watery substances as a hydraulic fluid in mining applications. The components have been found and further developed, and finally systems with linear and rotatory drives have been tested at various test facilities in order to derive information on the system behaviour of pressurized fluids and machinery components and their suitability for coal mining applications. (orig./CB) [Deutsch] In der untertaegigen Antriebstechnik sollen vermehrt Wasser und wasserhaltige Fluessigkeiten eingesetzt werden. Der Stand der Technik fuehrt bei der Anwendung von Wasserhydraulik immer wieder nur Einzelloesungen auf, die nicht allgemein und insbesondere im Steinkohlenbergbau angewendet werden koennen. Im Rahmen dieses Forschungsvorhabens wurden fuer die Wasserhydraulik geeignete Komponenten untersucht, weiterentwickelt und schliesslich Systeme mit linearen und rotatorischen Antrieben auf verschiedenen Pruefstaenden erprobt, um Aussagen ueber das Systemverhalten von Druckfluessigkeit und Bauelementen fuer Bergbauanwendungen zu bekommen. (orig./MSK)

Acoustic comunication systems and sounds in three species of crickets from central Italy: musical instruments for a three-voices composition

Science.gov (United States)

Monacchi, David; Valentini, Laura

2016-04-01

Natural soundscape has always constituted a reference in cognitive and emotional processes. The imitation of natural sounds contributed to the origin of the verbal language, which has been then subjected to an even more refined process of abstraction throughout history. The musical language also evolved along the same path of imitation. Among the many sonic elements of a natural environment, the stridulation of crickets is one of the most consistent for its timbre, articulation, diffusion and intrinsic emotional power. More than 900 species of crickets, in fact, have been described. They can be found in all parts of the world with the exception of cold regions at latitudes higher than 55° North and South. Among the many species we're working on (Order Orthoptera and Suborder Ensifera), we refer here of a comparison between the morphology of the acoustic emission systems and the corresponding waveforms/spectral patterns of sound in three widespread species from central Italy: Gryllus Bimaculatus, Acheta Domesticus (Gryllidae), and Ruspolia Nitidula (Conocephalidae). The samples of the acoustic apparatus of the target individuals, stored in ethanol, were observed under a Field Emission Gun Environmental Electron Scanning Microscope (FEG-ESEM, Quanta 200, FEI, The Netherlands). The use of this type of microscope allowed to analyze the samples without any kind of manipulation (dehydration and/or metallization), while maintaining the morphological features of the fragile acoustic apparatus. The observations were made with different sensors (SE: secondary-electron sensor and BSE: backscattered-electron sensor), and performed at low-medium vacuum with energies varying from c.ca 10 to 30kV. Male individuals have an acoustic apparatus consisting in two cuticular structures (tegmina) positioned above wings, while both male and females have receiving organs (tympanum) in forelegs. Stridulation mechanism is produced when the file and the scraper (plectrum) scrub one another

Design and fabrication of magnetic coolant filter

Science.gov (United States)

Prashanth, B. N.

2017-07-01

lose its strength even number of years of use. Dirty coolant is fed from the machines in to the reservoir of the coolant filter either by a pump or taken by the gravity and flows under the tray. This attracts the ferrous particles and builds up a cake of ferrous material and finally taken away by the scraper. The moving permanent magnets mounted on the shaft attracts ferrous chips and slide them on to plate and then to the discharge end or sludge bin. The coolant separated from chips flow back to the coolant tank. Well in this fast changing growth of metal working operation the recycling of cutting fluids become very important for the management of coolant. With the help of this developed model of magnetic coolant separator we can get highly efficient way of filtration guarantying fine finish, dimensional accuracy and increased tool life. The most significant role of this filter is that, it will reduce the waste disposal of coolant and a net profit for the production industries.

Influence of secondary settling tank performance on suspended solids mass balance in activated sludge systems.

Science.gov (United States)

Patziger, M; Kainz, H; Hunze, M; Józsa, J

2012-05-01

Secondary settling is the final step of the activated sludge-based biological waste water treatment. Secondary settling tanks (SSTs) are therefore an essential unit of producing a clear effluent. A further important function of SSTs is the sufficient thickening to achieve highly concentrated return sludge and biomass within the biological reactor. In addition, the storage of activated sludge is also needed in case of peak flow events (Ekama et al., 1997). Due to the importance of a high SST performance the problem has long been investigated (Larsen, 1977; Krebs, 1991; Takács et al., 1991; Ekama et al., 1997; Freimann, 1999; Patziger et al., 2005; Bürger et al., 2011), however, a lot of questions are still to solve regarding e.g. the geometrical features (inflow, outflow) and operations (return sludge control, scraper mechanism, allowable maximum values of surface overflow rates). In our study we focused on SSTs under dynamic load considering both the overall unsteady behaviour and the features around the peaks, investigating the effect of various sludge return strategies as well as the inlet geometry on SST performance. The main research tool was a FLUENT-based novel mass transport model consisting of two modules, a 2D axisymmetric SST model and a mixed reactor model of the biological reactor (BR). The model was calibrated and verified against detailed measurements of flow and concentration patterns, sludge settling, accompanied with continuous on-line measurement of in- and outflow as well as returned flow rates of total suspended solids (TSS) and water. As to the inlet arrangement a reasonable modification of the geometry could result in the suppression of the large scale flow structures of the sludge-water interface thus providing a significant improvement in the SST performance. Furthermore, a critical value of the overflow rate (q(crit)) was found at which a pronounced large scale circulation pattern develops in the vertical plane, the density current in

Associations of dairy cow behavior, barn hygiene, cow hygiene, and risk of elevated somatic cell count.

Science.gov (United States)

Devries, T J; Aarnoudse, M G; Barkema, H W; Leslie, K E; von Keyserlingk, M A G

2012-10-01

Poor dairy cow hygiene has been consistently associated with elevated somatic cell count (SCC) and the risk of subclinical mastitis. The objective of this study was to determine the associations between dairy cow standing and lying behavior, barn hygiene, cow hygiene, and the risk of experiencing elevated SCC. Lactating Holstein dairy cows (n=69; 86 ± 51 DIM; parity: 2.0 ± 1.2; means ± SD), kept in 1 of 2 groups, were monitored over a 4-mo period. Each group contained 61 ± 1 (mean ± SD) cows over the study period; complete data were obtained from 37 and 32 animals within each respective group. Cows were housed in a sand-bedded, freestall barn with 2 symmetrical pens, each with a free cow traffic automatic milking system. To vary barn hygiene, in 4 consecutive 28-d periods, alley manure scrapers in each of the 2 pens were randomly assigned to frequencies of operation of 3, 6, 12, and 24 times per day. During the last 7 d of each period, cow hygiene (upper leg/flank, lower legs, and udder; scale of 1 = very clean to 4 = very dirty) and stall hygiene (number of 0.15×0.15-m squares contaminated with manure in a 1.20×1.65-m grid) were recorded. Standing and lying behavior of the cows were collected during those days using data loggers. Individual-cow SCC was recorded at the beginning and end of each 28-d period. Elevated SCC was used as an indicator of subclinical mastitis; incidence of elevated SCC was defined as having a SCC >200,000 cells/mL at the end of each 28-d period, when SCC was <100,000 cells/mL at the beginning of the period. Less frequent scraping of the barn alleys was associated with cows having poorer hygiene. Poor udder hygiene was associated with poor stall hygiene. Longer lying duration was associated with poor hygiene of the upper legs/flank and udder. Greater premilking standing duration was associated with poor udder hygiene and decreased frequency of lying bouts was associated with poor hygiene of the lower legs. Higher milk yield was

Leaf degradation of Salix humboldtiana Willd: (Salicaceae and invertebrate colonization in a subtropical lake (Brazil Degradação foliar de Salix humboldtiana Willd: (Salicaceae e colonização por invertebrados em um lago subtropical (Brasil

Directory of Open Access Journals (Sweden)

Franko Telöken

2011-03-01

Full Text Available AIM: To evaluate leaf degradation and invertebrate colonization of Salix humboldtiana Willd. in a subtropical shallow lake on the coastal plain of Rio Grande do Sul, Brazil; METHODS: Litter bags containing 6.85 g of leaves were incubated in the superficial layer of sediment in the littoral region for 1, 4, 7, 14, 32, 47 and 71 days; RESULTS: After 71 days, a loss of 51% of the initial leaf weight was observed (k = 0.0100 d-1. We estimated that it would take 300 days to lose 95% of the initial weight. A total of 16040 organisms and 35 taxa were identified. Caenidae (25.9%, Oligochaeta (19%, Ostracoda (13.8%, Hydracarina (9.8%, Tanypodinae (9.7% and Coenagrionidae (7.7% were the most highly represented taxa. We observed increases in density, richness and diversity of taxa over time, with a stabilizing trend noted in the taxa diversity. Regarding the functional trophic groups (FTGs, gathering-collectors accounted for 57.6% of the community, while predators (25%, scrapers (15.8%, filtering-collectors (0.88% and shredders (0.73% were also represented. The diversity and evenness of the FTGs had stabilized by day 14; CONCLUSIONS: S. humboldtiana detritus provides a favorable habitat for a sufficient duration to support a high density and diversity of aquatic invertebrates. The small percentage of shredders indicates the minor influence of the invertebrate community on the rate of detrital degradation. The main contribution of invertebrates to detrital processing comes from the consumption of fine particulate organic matter by gathering-collectors.OBJETIVOS: Avaliar a degradação foliar de Salix humboldtiana Willd. e a colonização pela comunidade de invertebrados aquáticos em um lago raso subtropical, planície costeira do Rio Grande do Sul, Brasil; MÉTODOS: Bolsas de decomposição contendo 6,85 g de folhas foram incubadas na região litorânea, na superfície do sedimento, e retiradas após 1, 4, 7, 14, 32, 47 e 71 dias de decomposi

Design Drivers of Water Data Services

Science.gov (United States)

Valentine, D.; Zaslavsky, I.

2008-12-01

corresponding response element in WaterML: SitesResponse, VariableResponse, and TimeSeriesResponse. The WaterML specification is being adopted by federal agencies. The experimental USGS NWIS Daily Values web service returns WaterML-compliant TImeSeriesResponse. The National Climatic Data Center is also prototyping WaterML for data delivery, and has developed a REST-based service that generates WaterML- compliant output for the NCDC ASOS network. Such agency-supported web services coming online provide a much more efficient way to deliver agency data compared to the web site scraper services that the CUAHSI HIS project has developed initially. The CUAHSI water data web services will continue to serve as the main communication mechanism within CUAHSI HIS, connecting a variety of data sources with a growing set of web service clients being developed in both academia and the commercial sector. The driving forces for the development of web services continue to be: - Application experience and needs of the growing number of CUAHSI HIS users, who experiment with additional data types, analysis modes, data browsing and searching strategies, and provide feedback to WaterML developers; - Data description requirements posed by various federal and state agencies; - Harmonization with standards being adopted or developed in neighboring communities, in particular the relevant standards being explored within the Open Geospatial Consortium. CUAHSI WaterML is a standard output schema for CUAHSI HIS water web services. Its formal specification is available as OGC discussion paper at www.opengeospatial.org/standards/dp/ class="ab'>

Epuration des eaux usées de raffinerie par le procédé biologique des lits bactériens. Problèmes pratiques de l'exploitation Purifying Refinery Waste Water by the Bacterial Bed Biological Process. Practical Operational Problems

Directory of Open Access Journals (Sweden)

Leising M.

2006-11-01

filtration process is an interesting solution. Nonetheless, practical operating problems currently exist, and in particular the tendency for existing fixed film systems to become plugged up, resulting in the uncontrolled fouling of bulk liners. A study has shown that improper evacuation of the biomass are the cause of the problem. An investigation of how to control this phenomenon shows a distinction between curative and preventive measures. Curative measures consisting in regenerating the filter packing by increasing the hydraulic loading and by chemical or mechanical cleaning do not give full satisfaction. Among preventive measures, one method consists in reducing the organic loading of the effluent: phenol-containing waste waters are desalinated, waters from DGO and FCC are stripped, alcaline waters are reinjected into the crude oil, oils are recovered. just downstream from where they are discharged, and primary treatments are optimized, in particular by the installation of scrapers and oleophilic drums on the API separators and by a better choice of flocculants. Nevertheless, experience shows that this method does not delay plugging. The best method is in choosing contact medium, as is shown by comparative pilot-plant texts performed by Institut National de Recherche Chimique Appliquée (lRCHA and Compagnie Française de Raffinage (CFR. These tests were concentrated on the fate of the specific gravity of the packing on purifying performances and on sludge quality; they have showes that cloisonyle forming a tubular packing is probable the best suited material.

Impacto da remoção de biofilme lingual em pacientes sob ventilação mecânica Impact of tongue biofilm removal on mechanically ventilated patients

Directory of Open Access Journals (Sweden)

Paulo Sérgio da Silva Santos

2013-03-01

. METHODS: Tongue biofilm and tracheal secretion samples were collected from a total of 50 patients: 27 in the study group (SG who were intubated or tracheostomized under assisted ventilation and treated with the tongue cleaner and 23 in the control group (CG who did not undergo tongue cleaning. Oral and tracheal secretion cultures of the SG (initially and after 5 days and the CG (at a single time-point were performed to evaluate the changes in bacterial flora. RESULTS: The median age of the SG patients was 77 years (45-99 years, and that of the CG patients was 79 years (21-94 years. The length of hospital stay ranged from 17-1,370 days for the SG with a median stay of 425 days and from 4-240 days for the CG with a median stay of 120 days. No significant differences were found when the dental plaque indexes were compared between the SG and the CG. There was no correlation between the index and the length of hospital stay. The same bacterial flora was found in the dental plaque of 9 of the 27 SG patients before and after the tongue scraper was used for 5 days compared with the CG (p=0.683. Overall, 7 of the 27 SG patients had positive bacterial cultures for the same strains in both tongue biofilm and tracheal secretions compared with the CG (p=0.003. Significant similarities in strain resistance and susceptibility of the assessed microorganisms were observed between oral and tracheal microflora in 6/23 cases in the CG (p=0.006. CONCLUSION: The use of a tongue cleaner is effective at reducing tongue biofilm in patients on mechanical ventilation and facilitates oral hygiene interventions performed by caregivers.

Modeling of the height control system using artificial neural networks

Directory of Open Access Journals (Sweden)

A. R Tahavvor

2016-09-01

Full Text Available Introduction Automation of agricultural and machinery construction has generally been enhanced by intelligent control systems due to utility and efficiency rising, ease of use, profitability and upgrading according to market demand. A broad variety of industrial merchandise are now supplied with computerized control systems of earth moving processes to be performed by construction and agriculture field vehicle such as grader, backhoe, tractor and scraper machines. A height control machine which is used in measuring base thickness is consisted of two mechanical and electronic parts. The mechanical part is consisted of conveyor belt, main body, electrical engine and invertors while the electronic part is consisted of ultrasonic, wave transmitter and receiver sensor, electronic board, control set, and microcontroller. The main job of these controlling devices consists of the topographic surveying, cutting and filling of elevated and spotted low area, and these actions fundamentally dependent onthe machine's ability in elevation and thickness measurement and control. In this study, machine was first tested and then some experiments were conducted for data collection. Study of system modeling in artificial neural networks (ANN was done for measuring, controlling the height for bases by input variable input vectors such as sampling time, probe speed, conveyer speed, sound wave speed and speed sensor are finally the maximum and minimum probe output vector on various conditions. The result reveals the capability of this procedure for experimental recognition of sensors' behavior and improvement of field machine control systems. Inspection, calibration and response, diagnosis of the elevation control system in combination with machine function can also be evaluated by some extra development of this system. Materials and Methods Designing and manufacture of the planned apparatus classified in three dissimilar, mechanical and electronic module, courses of

Zile Elbaşoğlu Camii’nin Sıvalar Altında Kalan Gizemi The Mystery Of The Zile-Elbaşoğlu Mosque Remains Under Plasters

Directory of Open Access Journals (Sweden)

Ali Murat AKTEMUR

2013-09-01

Full Text Available Elbaşoğlu Mosque was built in 1801 by Ahmet Aga, clean-cutstone architecture, square, rectangular with remarkable inscriptionsElbaşoğlu Mosque is one of the local mosque, wood-backed and woodenceilings. Until 2007, the walls and the ceiling, and even the altar,wooden support, wood columns, wooden gallery, galleries, in short, allthe wooden elements of the mosque was covered with oil on sweet-limeplaster. In 2007, during the repair of the roof of a simple chance, withplaster falling due to the flowing water under the pen-and-repair workon the emergence of ornaments and wooden decorations samples, thenstopped cleaning and scraper operations in the administration of theGeneral Directorate of Foundations in the interior of the mosque penrichsamples of work, with examples of wooden decorative plaster underthe mystery was revealed.Cover at the top of the walls combined with Harim calligraphy ona black background with spots, including a concave border of the beltframed verse was written. Verse generation raised on the corners of theceiling moldings created crash of beads, triangle, octagon in the middleof a field, and thus created the split surfaces. Located in the middle ofthe octagon octagon-shaped belly, finished with carving technique,baroque decorated with floral motifs. the four corners of the triangularroof panels are decorated with reliefs excess plastic plant. Pen-workdecoration floral motifs on the walls, gallery, pulpits, pillars, such asthe carved wooden elements fall floral and geometric motifs are carvedin the mosque offers a wealth of eye-catching as almost free space left.Made in 1801, in the early years of the Republic, the region'sunique sweet-lime paint on plaster taken off this rich decoration, woodart and pen-work ornamentation Turkey offers one of the richest. Tokat Zile’de Elbaşoğlu Ahmet Ağa tarafından 1801 yılında inşa ettirilen, düzgün kesme taş mimarisi, kitabeleri ile dikkat çeken, kareye yakın dikd

The evolution of the CUAHSI Water Markup Language (WaterML)

Science.gov (United States)

Zaslavsky, I.; Valentine, D.; Maidment, D.; Tarboton, D. G.; Whiteaker, T.; Hooper, R.; Kirschtel, D.; Rodriguez, M.

2009-04-01

agencies. The experimental USGS NWIS Daily Values web service returns WaterML-compliant TimeSeriesResponse. NCDC is also prototyping WaterML for data delivery, and has developed a REST-based service that generates WaterML- compliant output for its integrated station network. These agency-supported web services provide a much more efficient way to deliver agency data compared to the web site scraper services that the CUAHSI HIS project developed initially. Adoption of WaterML by the US Geological Survey is particularly significant because the USGS maintains by far the largest water data repository in the United States. For version 1.1, WaterML has evolved to reflect the deployment experience at hydrologic observatory testbeds, as well as feedback from hydrologic data repository managers at federal and state agencies. Further development of WaterML and enhancement of the underlying information model is the focus of the recently established OGC Hydrology Domain Working Group, whose mission is to profile OGC standards (GML, O&M, SOS, WCS, WFS) for the water resources domain and thus ensure WaterML's wider applicability and easier implementation. WaterML 2.0 is envisioned as an OGC-compliant application schema that supports OGC features, can express different types of observations and various groupings of observations, and allows researchers to define custom metadata elements. This presentation will discuss the information model underlying WaterML and describe the rationale, design drivers and evolution of WaterML and the water data services, illustrating their recent application in the context of CUAHSI HIS and the hydrologic observatory testbeds.

Characterization of water quality and biological communities, Fish Creek, Teton County, Wyoming, 2007-2011

Science.gov (United States)

Eddy-Miller, Cheryl A.; Peterson, David A.; Wheeler, Jerrod D.; Edmiston, C. Scott; Taylor, Michelle L.; Leemon, Daniel J.

2013-01-01

relative abundance of Ephemeroptera, Plecoptera, and Trichoptera, which tend to be intolerant of water-quality degradation, decreased from April/May to August; the same time period saw a corresponding increase in Diptera and noninsects, particularly Oligochaeta (worms) that are more tolerant. Seasonal changes in macroinvertebrate functional feeding groups were significantly different. The relative abundance of gatherer-collector and scraper feeding groups decreased from April/May to August, accompanied by an increase in filterer-collector and shredders feeding groups. Seasonal changes in feeding groups might be due to the seasonal shift in aquatic plant communities, as indicated by comparison with other streams in the area that had fewer aquatic macrophytes than Fish Creek. Statistical tests of macroinvertebrate metrics indicated few differences between years or biological sampling sites on Fish Creek, although the site farthest upstream sometimes was different not only in terms of macroinvertebrates but also in streamflow, water quality, and aquatic plants. Potential effects of contributions of additional nutrients to the Fish Creek ecosystem beyond the conditions sampled during the study period are not known. However, because virtually all of the detectable dissolved nitrate commonly was consumed by aquatic plants in August (leaving dissolved nitrate less than the reporting level in water samples), it is possible that increased nutrient contributions could cause increased growth of aquatic plants. Additional long-term monitoring of the stream, with concurrent data analysis and interpretation would be needed to determine the effects of additional nutrients on the aquatic plant community and on higher levels of the food chain.

Control of the magnetic topology and plasma exhaust in the edge region of Wendelstein 7-X. A numerical study

Energy Technology Data Exchange (ETDEWEB)

Hoelbe, Hauke

2016-02-15

detail. In this thesis, state-of-the-art codes are used to analyze this previously proposed mitigation strategy; they are also used to develop several alternative mitigation schemes, which may in the end be advantageous. The work performed here shows not only that it is conceivable to solve this already identified problem in new and arguably better ways but also that the W7-X coil set has enough degrees of freedom that many important long-pulse plasma e.ects can be e.ectively mimicked in short-pulse operation. This opens up a rich research program in the early phases of operation and may therefore lead to a significant acceleration of the scientific program to control and optimize the divertor operation in W7-X. The main scientific challenge for the island divertor operation in W7-X is that, since the divertor geometry is now fixed, the magnetic field structure must be adjusted to the divertor geometry, or additional plasma-facing components must be manufactured and installed. Well before this thesis work was done, such additional plasma-facing components were proposed. These are called scraper elements (SEs). As a part of this work, computer simulations were performed in order to obtain a better knowledge base regarding the SEs. To analyze the e.ect of the SE, edge plasma physics simulation code EMC3-Eirene, was used, in combination with state-of-the-art magneto hydrodynamic (MHD) equilibrium codes. This combination was computationally non-trivial and new, and it has led to important insights. One main result of this study is that the SEs significantly reduce the particle exhaust capabilities in steady state operation; this is a concern for W7-X. To test and further quantify this deleterious effect, physics experiments with a prototype SE should be performed as soon as possible, ideally in the first operation campaigns before the approximately two-year break needed to complete W7-X for steady-state operation. In this first operation phase, however, the necessary

Control of the magnetic topology and plasma exhaust in the edge region of Wendelstein 7-X. A numerical study

International Nuclear Information System (INIS)

Hoelbe, Hauke

2016-01-01

detail. In this thesis, state-of-the-art codes are used to analyze this previously proposed mitigation strategy; they are also used to develop several alternative mitigation schemes, which may in the end be advantageous. The work performed here shows not only that it is conceivable to solve this already identified problem in new and arguably better ways but also that the W7-X coil set has enough degrees of freedom that many important long-pulse plasma e.ects can be e.ectively mimicked in short-pulse operation. This opens up a rich research program in the early phases of operation and may therefore lead to a significant acceleration of the scientific program to control and optimize the divertor operation in W7-X. The main scientific challenge for the island divertor operation in W7-X is that, since the divertor geometry is now fixed, the magnetic field structure must be adjusted to the divertor geometry, or additional plasma-facing components must be manufactured and installed. Well before this thesis work was done, such additional plasma-facing components were proposed. These are called scraper elements (SEs). As a part of this work, computer simulations were performed in order to obtain a better knowledge base regarding the SEs. To analyze the e.ect of the SE, edge plasma physics simulation code EMC3-Eirene, was used, in combination with state-of-the-art magneto hydrodynamic (MHD) equilibrium codes. This combination was computationally non-trivial and new, and it has led to important insights. One main result of this study is that the SEs significantly reduce the particle exhaust capabilities in steady state operation; this is a concern for W7-X. To test and further quantify this deleterious effect, physics experiments with a prototype SE should be performed as soon as possible, ideally in the first operation campaigns before the approximately two-year break needed to complete W7-X for steady-state operation. In this first operation phase, however, the necessary

Some Applications of Radioisotopes of Short Half-Life in the French Gas Industry; Quelques Applications des Radioelements a Periode Courte dans l'Industrie Gazoere Francaise; НЕКОТОРЫЕ ВИДЫ ПРИМЕНЕНИЯ КОРОТКОЖИВУЩИХ РАДИОЭЛЕМЕНТОВ ВО ФРАНЦУЗСКОЙ ГАЗОВОЙ ПРОМЫШЛЕННОСТИ; Algunas Aplicaciones de los Radioelementos de Periqdo Corto en la Industria Francesa del Gas

Energy Technology Data Exchange (ETDEWEB)

Tellier, C. [Gaz de France, Paris (France); Courtois, G.; Gasnier, M. [Centre d' Etudes Nucleaires, Saclay (France)

1963-03-15

For the purpose of keeping rubber jointings in old gas piping systems in good condition, certain hydrocarbides in very weak concentration are injected into the system in the form of aerosols. Bromonaphthalene hydrocarbide labelled with bromine-82 is added in order to determine the reach of the aerosols. The quantity of tracer recovered, on filter-paper discs distributed along the system, is determined by counting with an end-window counter. Four millicuries of bromonaphthalene sufficed to trace the hydrocarbide over a length of 7 km in a conduit 15 cm diam. Municipal gas authorities stipulate a minimum rate of air renewal in domestic premises. For the purpose of checking this rate, xenon-133 is diffused throughout the premises and the change in concentration is measured by means of a scintillation counter. Concentrations of the order of 0.5 mc/m{sup 3} are sufficient. The reproducibility of results is greatly superior to that obtained with conventional methods. The principle of isotopic methods of leak detection is well-known. In order to perfect these methods for industrial purposes, an experimental pipeline, 140 m in length and 25 cm diam., was installed underground at Saclay, at a depth of 1.10 m. This pipe has five experimental leakage points, with adjustable discharge, located in different kinds of soil (sand, chalk, clay, local Saclay earth). The first results obtained with this installation are described below. A description is given of pressure tests carried out to check water-leak-tightness prior to putting new conduits into service. Sodium-24 in the form of bicarbonate is used as tracer, and detection is done from inside the conduit by means of a scraper piston enclosing a self-contained Geiger-counter measuring unit and a magnetic recorder. The difficulties encountered in perfecting this apparatus are described. The graph obtained after decoding shows a very marked peak for every leak, the position of each being determined to within about 2 m. For easy