WorldWideScience

Sample records for school bus riders

  1. Tohyco-Rider: hybrid bus with super-caps and inductive power transfer

    Energy Technology Data Exchange (ETDEWEB)

    Harri, V.; Carriero, D. [HTA Luzern, Horw (Switzerland)

    2004-07-01

    The TOHYCO-Rider-Bus was developed during a Swiss research project at HTA Lucerne (University of Applied Sciences of Central Switzerland). Each time, the bus only picks up enough energy to safely reach the next charging station. Instead of common re-chargeable batteries, the TOHYCO-Rider uses electrical high-power capacitors, so-called super-capacitors, as energy storage. In combination with an absolutely non-dangerous, non-contact, inductive energy re-charging system the S-CAPs can be reloaded with a higher efficiency and much more quickly than batteries. Within 3-5 minutes of charging time the vehicle is prepared for its next trip. A further advantage of this concept is that, with the S-CAPs, only the energy supply has to be taken along for the next stop (approx. 300 kg) and not a charge of batteries for the entire day (approx. 2t). Because of the lighter weight, the TOHYCO-Rider is therefore an economically and ecologically interesting mean of transportation. In summer 2004 the TOHYCO-Rider ran in a pilot operation. During three months the mini-bus drove in a time-scheduled operation in the city of Lucerne, with the aim of proving the reliability and fitness of the developed system in daily operation. The test operation was terminated recently and the results were very promising. (authors)

  2. School Bus Accidents and Driver Age.

    Science.gov (United States)

    McMichael, Judith

    The study examines the rates and types of school bus accidents according to the age of the school bus driver. Accident rates in North Carolina for the school year 1971-72 were analyzed using three sources of data: accident reports, driver and mileage data, and questionnaires administered to a sample of school bus drivers. Data were obtained on…

  3. School Bus Accidents: Reducing Incidents and Injuries

    Science.gov (United States)

    Mahoney, Daniel

    2009-01-01

    The number of children injured in nonfatal school bus accidents annually is more than double the number previously estimated. In Ohio alone, approximately 20,800 children younger than 18 were occupants of school buses that were involved in crashes in 2003 and 2004 (McGeehan 2007). Among those children, most had minor or no injuries. However, there…

  4. Advanced Competencies for School Bus Drivers.

    Science.gov (United States)

    Illinois State Board of Education, Springfield.

    Four units are provided for formal classroom instruction in advanced competencies for school bus drivers in Illinois. Units cover passenger control, accidents and emergencies, detecting hazards, and first aid. Each unit contains some or all of the following components: table of contents; a list of objectives; informative material, including an…

  5. For Safety and Sanity's Sake, Help Bus Drivers Keep Peace on the Ride to School.

    Science.gov (United States)

    Trotter, Andrew

    1987-01-01

    Outlines common-sense tips for disciplining student bus riders that are recommended by several driver-training programs. Themes include the following: (1) Set a few clear rules for proper bus behavior; (2) be positive; and (3) establish amiable communication with the children and with the principal as well. (CJH)

  6. Illinois School Bus Driver Instructional Program. Trainee Guide. Revised.

    Science.gov (United States)

    Illinois State Board of Education, Springfield.

    This trainee guide contains six units of materials for use by those studying to become school bus drivers in the State of Illinois. Covered in the units are the following topics: school bus driver role and responsibility, passenger control, first aid, driving fundamentals, accidents and emergencies, and detecting hazards. Each unit contains a…

  7. School Bus Safety: What Can Our Schools Do to Protect Our Children?

    Science.gov (United States)

    Dargan, Thomas J.; Silverstone, Adam H.

    2014-01-01

    School districts and school bus contractors are entrusted with the most important of all road users--our nation's children. In the wake of recent newsworthy accidents and attention grabbing headlines regarding unfit bus drivers, claims premised upon school bus accidents have become increasingly tangential and, in turn, personal injury attorneys…

  8. Improving School Bus Safety. Transportation Research Board Special Report 222.

    Science.gov (United States)

    National Academy of Sciences - National Research Council, Washington, DC. Transportation Research Board.

    While school buses transport more passengers per trip, the rate of occupant fatalities per mile driven for school buses is one-quarter that for passenger cars. Nevertheless, the public expects school districts and other school bus operators to take all reasonable precautions to protect children as they travel to and from school. Although a variety…

  9. The Wheels on the Bus Go “Buy Buy Buy”: School Bus Advertising Laws

    Science.gov (United States)

    2012-01-01

    School buses, a practical necessity for millions of children, are at the center of new efforts to raise revenue. School bus advertising laws bring public health and commercialization concerns to the school setting. In doing so, they potentially expose school districts to First Amendment lawsuits. I examined various school bus advertising bills and laws. I reviewed First Amendment “forum analysis” as applied in the transit and school settings to clarify how this legal test may affect school districts subject to such laws. I have made recommendations for school districts to enact appropriate policies to ensure that such advertising does not undermine public health and to enable the districts to maintain control over their property. PMID:22742065

  10. The wheels on the bus go "buy buy buy": school bus advertising laws.

    Science.gov (United States)

    Pomeranz, Jennifer L

    2012-09-01

    School buses, a practical necessity for millions of children, are at the center of new efforts to raise revenue. School bus advertising laws bring public health and commercialization concerns to the school setting. In doing so, they potentially expose school districts to First Amendment lawsuits. I examined various school bus advertising bills and laws. I reviewed First Amendment "forum analysis" as applied in the transit and school settings to clarify how this legal test may affect school districts subject to such laws. I have made recommendations for school districts to enact appropriate policies to ensure that such advertising does not undermine public health and to enable the districts to maintain control over their property.

  11. How to Reduce Those Costly School Bus Accidents.

    Science.gov (United States)

    Farmer, Ernest

    1985-01-01

    The deterrent to school bus accidents is preparedness. Training programs for drivers and mechanics, equipment specifications, and a community support base are some of the ways to prevent tragedy. (MLF)

  12. High-Tech School Bus Teaches Students on the Road

    Science.gov (United States)

    Katims, Lauren

    2011-01-01

    Last year, kindergarten through high school students in the rural Hector, Arkansas, School District barely had the technology resources that keep kids interested in math and science. This year, they potentially have the most advanced resources in the country--before they even step into the classroom. One school bus in Arkansas' Pope County has…

  13. Implementation of a Walking School Bus: Lessons Learned

    Science.gov (United States)

    Kong, Alberta S.; Sussman, Andrew L.; Negrete, Sylvia; Patterson, Nissa; Mittleman, Rachel; Hough, Richard

    2009-01-01

    Background: Obesity is rapidly becoming the most common chronic medical condition affecting children. To address this crisis, an Albuquerque, New Mexico, elementary school partnered with University of New Mexico researchers and conducted a Walking School Bus (WSB). The purpose of this article is to examine the feasibility of implementing a WSB.…

  14. The Safety Tips for ATV Riders (STARs) programme: short-term impact of a school-based educational intervention.

    Science.gov (United States)

    Jennissen, Charles A; Peck, Jeffrey; Wetjen, Kristel; Hoogerwerf, Pam; Harland, Karisa K; Denning, Gerene M

    2015-06-01

    Since 1985, one-third of all US all-terrain vehicle (ATV)-related injuries and one-quarter of deaths involved victims safety education of youth could help reduce these tragedies. To assess the efficacy of the Safety Tips for ATV Riders (STARs) school-based programme targeting adolescents. A survey was anonymously administered before and after the programme to determine demographics, knowledge and reported likelihood of using the information learned. Over 4600 students in 30 Iowa schools participated from November 2010 to April 2013. Initially, 52% knew most ATVs are designed for one rider, 25% knew the recommended vehicle size for their age range and 42% knew riding on Iowa's roads was legal only for agricultural purposes. After the programme, this increased to 92%, 82% and 76%, respectively (psafety information learned, respectively; younger students, females and infrequent riders reported higher likelihoods. STARs increased short-term ATV safety knowledge and almost half the participants reported they would use the safety information presented. Males and frequent riders seemed more resistant, but some groups that may be more vulnerable to potential ATV crash and injury appeared amenable to the training with higher increases in postprogramme scores and greater intention of improving safety behaviours. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  15. 49 CFR 383.123 - Requirements for a school bus endorsement.

    Science.gov (United States)

    2010-10-01

    ... devices required for school buses by State or Federal law or regulation. (ii) Emergency exits and... 49 Transportation 5 2010-10-01 2010-10-01 false Requirements for a school bus endorsement. 383.123... Requirements for a school bus endorsement. (a) An applicant for a school bus endorsement must satisfy the...

  16. The Role of the Coroner in School Bus Accident Prevention: Some Recommendations.

    Science.gov (United States)

    Fox, Michael

    1995-01-01

    Following the deaths of two elementary school students in bus-related accidents in 1992, the Coroner of Quebec held extensive hearings investigating school bus safety and accident prevention. A subsequent report addressed responsibilities of government and school board officials to correct deficiencies in school bus services and provided…

  17. GeoBus: sharing science research with schools

    Science.gov (United States)

    Roper, Kathryn; Robinson, Ruth; Moorhouse, Ben

    2016-04-01

    GeoBus (www.geobus.org.uk) is an educational outreach project that was developed in 2012 by the Department of Earth and Environmental Sciences at the University of St Andrews, and it is currently sponsored by industry, NERC, The Crown Estate, and the Scottish Government. The aims of GeoBus are to support the teaching of Earth Science in secondary (middle and high) schools by providing teaching support to schools that have little or no experience in teaching this subject. This is, in part, done through the sharing of new science research outcomes and the experiences of young researchers with school pupils to provide a bridge between industry, higher education institutions, research councils and schools. Since its launch, over 40,000 pupils will have been involved in experiential Earth science learning activities in 190 different schools (over 400 separate visits) across the length and breadth of Scotland: many of these schools are in remote and disadvantaged regions. A new GeoBus project is under development within the Department of Earth Sciences at UCL in London. A key aim of GeoBus is to incorporate new research into our workshops with the main challenge being the development of appropriate resources that incorporate the key learning aims and requirements of the science and geography curricula. GeoBus works closely with researchers, teachers and educational practitioners to tailor the research outcomes to the curricula as much as possible. Over the past four years, GeoBus has developed 17 workshops, 5 challenge events and extensive field trips and each of these activities are trialled and evaluated within the university, and adjustments are made before the activities are delivered in schools. Activities are continually reviewed and further developments are made in response to both teacher and pupil feedback. This critical reflection of the project's success and impact is important to insure a positive and significant contribution to the science learning in

  18. Wisdom and Bus Schedules: Developing School Leadership

    Science.gov (United States)

    Glatter, Ron

    2009-01-01

    This article is based on a synthesis study of school leadership development conducted for the National College of School Leadership (NCSL) in England. It first outlines a perspective on leadership focusing on the concepts of wisdom, deliberation and higher order capacities. Then it describes and assesses two distinct models of leadership learning,…

  19. Iterated Local Search Algorithm with Strategic Oscillation for School Bus Routing Problem with Bus Stop Selection

    Directory of Open Access Journals (Sweden)

    Mohammad Saied Fallah Niasar

    2017-02-01

    Full Text Available he school bus routing problem (SBRP represents a variant of the well-known vehicle routing problem. The main goal of this study is to pick up students allocated to some bus stops and generate routes, including the selected stops, in order to carry students to school. In this paper, we have proposed a simple but effective metaheuristic approach that employs two features: first, it utilizes large neighborhood structures for a deeper exploration of the search space; second, the proposed heuristic executes an efficient transition between the feasible and infeasible portions of the search space. Exploration of the infeasible area is controlled by a dynamic penalty function to convert the unfeasible solution into a feasible one. Two metaheuristics, called N-ILS (a variant of the Nearest Neighbourhood with Iterated Local Search algorithm and I-ILS (a variant of Insertion with Iterated Local Search algorithm are proposed to solve SBRP. Our experimental procedure is based on the two data sets. The results show that N-ILS is able to obtain better solutions in shorter computing times. Additionally, N-ILS appears to be very competitive in comparison with the best existing metaheuristics suggested for SBRP

  20. Case Study - Propane School Bus Fleets

    Energy Technology Data Exchange (ETDEWEB)

    Laughlin, M; Burnham, A.

    2014-08-31

    As part of the U.S. Department of Energy’s (DOE’s) effort to deploy transportation technologies that reduce U.S. dependence on imported petroleum, this study examines five school districts, one in Virginia and four in Texas, successful use of propane school buses. These school districts used school buses equipped with the newly developed liquid propane injection system that improves vehicle performance. Some of the school districts in this study saved nearly 50% on a cost per mile basis for fuel and maintenance relative to diesel. Using Argonne National Laboratory’s Alternative Fuel Life-Cycle Environmental and Economic Transportation (AFLEET) Tool developed for the DOE’s Clean Cities program to help Clean Cities stakeholders estimate petroleum use, greenhouse gas (GHG) emissions, air pollutant emissions and cost of ownership of light-duty and heavy-duty vehicles, the results showed payback period ranges from 3—8 years, recouping the incremental cost of the vehicles and infrastructure. Overall, fuel economy for these propane vehicles is close to that of displaced diesel vehicles, on an energy-equivalent basis. In addition, the 110 propane buses examined demonstrated petroleum displacement, 212,000 diesel gallon equivalents per year, and GHG benefits of 770 tons per year.

  1. School Bus Transportation of Children With Special Health Care Needs.

    Science.gov (United States)

    O'Neil, Joseph; Hoffman, Benjamin D

    2018-05-01

    School systems are responsible for ensuring that children with special needs are safely transported on all forms of federally approved transportation provided by the school system. A plan to provide the most current and proper support to children with special transportation needs should be developed by the Individualized Education Program team, including the parent, school transportation director, and school nurse, in conjunction with physician orders and recommendations. With this statement, we provide current guidance for the protection of child passengers with specific health care needs. Guidance that applies to general school transportation should be followed, inclusive of staff training, provision of nurses or aides if needed, and establishment of a written emergency evacuation plan as well as a comprehensive infection control program. Researchers provide the basis for recommendations concerning occupant securement for children in wheelchairs and children with other special needs who are transported on a school bus. Pediatricians can help their patients by being aware of guidance for restraint systems for children with special needs and by remaining informed of new resources. Pediatricians can also play an important role at the state and local level in the development of school bus specifications. Copyright © 2018 by the American Academy of Pediatrics.

  2. San Antonio's 1983 Bus Passenger Survey

    Science.gov (United States)

    1983-10-01

    Many transit operators routinely collect ridership data in order to provide a : basis for the planning of bus services. Often a survey is conducted of bus : riders to determine their riding habits, their views about the quality of : current service, ...

  3. IMPACTS OF BUS STOP IMPROVEMENTS

    Science.gov (United States)

    2018-03-23

    Improving bus stops by providing shelters, seating, signage, and sidewalks is relatively inexpensive and popular among riders and local officials. Making such improvements, however, is not often a priority for U.S. transit providers because of compet...

  4. Effects of the window openings on the micro-environmental condition in a school bus

    Science.gov (United States)

    Li, Fei; Lee, Eon S.; Zhou, Bin; Liu, Junjie; Zhu, Yifang

    2017-10-01

    School bus is an important micro-environment for children's health because the level of in-cabin air pollution can increase due to its own exhaust in addition to on-road traffic emissions. However, it has been challenging to understand the in-cabin air quality that is associated with complex airflow patterns inside and outside a school bus. This study conducted Computational Fluid Dynamics (CFD) modeling analyses to determine the effects of window openings on the self-pollution for a school bus. Infiltration through the window gaps is modeled by applying variable numbers of active computational cells as a function of the effective area ratio of the opening. The experimental data on ventilation rates from the literature was used to validate the model. Ultrafine particles (UFPs) and black carbon (BC) concentrations were monitored in ;real world; field campaigns using school buses. This modeling study examined the airflow pattern inside the school bus under four different types of side-window openings at 20, 40, and 60 mph (i.e., a total of 12 cases). We found that opening the driver's window could allow the infiltration of exhaust through window/door gaps in the back of school bus; whereas, opening windows in the middle of the school bus could mitigate this phenomenon. We also found that an increased driving speed (from 20 mph to 60 mph) could result in a higher ventilation rate (up to 3.4 times) and lower mean age of air (down to 0.29 time) inside the bus.

  5. School bus pollution and changes in the air quality at schools: a case study.

    Science.gov (United States)

    Li, Chunlei; Nguyen, Quyen; Ryan, Patrick H; Lemasters, Grace K; Spitz, Henry; Lobaugh, Megan; Glover, Samuel; Grinshpun, Sergey A

    2009-05-01

    Millions of children attending US schools are exposed to traffic-related air pollutants, including health-relevant ultrafine aerosols generated from school buses powered with diesel fuel. This case study was established in a midwestern (USA) metropolitan area to determine the concentration and elemental composition of aerosol in the vicinity of a public school during morning hours when the bus traffic in and out of the adjacent depot was especially intense. Simultaneous measurements were performed at a control site. The ambient aerosol was first characterized in real time using a particle size selective aerosol spectrometer and then continuously monitored at each site with a real-time non-size-selective instrument that detected particles of 20 nm to >1 microm. In addition, air samples were collected with PM2.5 Harvard Impactors and analyzed for elemental composition using the X-ray fluorescence technique (for 38 elements) and thermal-optical transmittance (for carbon). The measurements were conducted during two seasons: in March at ambient temperature around 0 degrees C and in May when it ranged mostly between 10 and 20 degrees C. The particle number concentration at the test site exhibited high temporal variability while it was time independent at the control site. Overall, the aerosol particle count at the school was 4.7 +/- 1.0 times (March) and 2.2 +/- 0.4 times (May) greater than at the control site. On some days, a 15 min-averaged particle number concentration showed significant correlation with the number of school bus arrivals and departures during these time intervals. On other days, the correlation was less than statistically significant. The 3 h time-averaged particle concentrations determined in the test site on days when the school buses operated were found to be more than two-fold greater (on average) than those measured on bus-free days at the same location, and this difference was statistically significant. Overall, the data suggest a possible

  6. Characterizing the range of children's air pollutant exposure during school bus commutes.

    Science.gov (United States)

    Sabin, Lisa D; Behrentz, Eduardo; Winer, Arthur M; Jeong, Seong; Fitz, Dennis R; Pankratz, David V; Colome, Steven D; Fruin, Scott A

    2005-09-01

    Real-time and integrated measurements of gaseous and particulate pollutants were conducted inside five conventional diesel school buses, a diesel bus with a particulate trap, and a bus powered by compressed natural gas (CNG) to determine the range of children's exposures during school bus commutes and conditions leading to high exposures. Measurements were made during 24 morning and afternoon commutes on two Los Angeles Unified School District bus routes from South to West Los Angeles, with seven additional runs on a rural/suburban route, and three runs to test the effect of window position. For these commutes, the mean concentrations of diesel vehicle-related pollutants ranged from 0.9 to 19 microg/m(3) for black carbon, 23 to 400 ng/m(3) for particle-bound polycyclic aromatic hydrocarbon (PB-PAH), and 64 to 220 microg/m(3) for NO(2). Concentrations of benzene and formaldehyde ranged from 0.1 to 11 microg/m(3) and 0.3 to 5 microg/m(3), respectively. The highest real-time concentrations of black carbon, PB-PAH and NO(2) inside the buses were 52 microg/m(3), 2000 ng/m(3), and 370 microg/m(3), respectively. These pollutants were significantly higher inside conventional diesel buses compared to the CNG bus, although formaldehyde concentrations were higher inside the CNG bus. Mean black carbon, PB-PAH, benzene and formaldehyde concentrations were higher when the windows were closed, compared with partially open, in part, due to intrusion of the bus's own exhaust into the bus cabin, as demonstrated through the use of a tracer gas added to each bus's exhaust. These same pollutants tended to be higher on urban routes compared to the rural/suburban route, and substantially higher inside the bus cabins compared to ambient measurements. Mean concentrations of pollutants with substantial secondary formation, such as PM(2.5), showed smaller differences between open and closed window conditions and between bus routes. Type of bus, traffic congestion levels, and encounters with

  7. Walking school bus programs in U.S. public elementary schools.

    Science.gov (United States)

    Turner, Lindsey; Chriqui, Jamie F; Chaloupka, Frank J

    2013-07-01

    Active transportation to school provides an important way for children to meet physical activity recommendations. The "walking school bus" (WSB) is a strategy whereby adults walk with a group of children to and from school along a fixed route. This study assessed whether school-organized WSB programs varied by school characteristics, district policies, and state laws. School data were gathered by mail-back surveys in nationally representative samples of U.S. public elementary schools during the 2008-2009 and 2009-2010 school years (n = 632 and 666, respectively). Corresponding district policies and state laws were obtained. Nationwide, 4.2% of schools organized a WSB program during 2008-2009, increasing to 6.2% by 2009-2010. Controlling for demographic covariates, schools were more likely to organize a WSB program where there was a strong district policy pertaining to safe active routes to school (OR = 2.14, P law requiring crossing guards around schools (OR = 2.72, P laws are associated with an increased likelihood of elementary schools organizing these programs. Policymaking efforts may encourage schools to promote active transportation.

  8. Performance of school bus retrofit systems: ultrafine particles and other vehicular pollutants.

    Science.gov (United States)

    Zhang, Qunfang; Zhu, Yifang

    2011-08-01

    This study evaluated the performance of retrofit systems for diesel-powered school buses, a diesel oxidation catalyst (DOC) muffler and a spiracle crankcase filtration system (CFS), regarding ultrafine particles (UFPs) and other air pollutants from tailpipe emissions and inside bus cabins. Tailpipe emissions and in-cabin air pollutant levels were measured before and after retrofitting when the buses were idling and during actual pick-up/drop off routes. Retrofit systems significantly reduced tailpipe emissions with a reduction of 20-94% of total particles with both DOC and CFS installed. However, no unequivocal decrease was observed for in-cabin air pollutants after retrofitting. The AC/fan unit and the surrounding air pollutant concentrations played more important roles for determining the in-cabin air quality of school buses than did retrofit technologies. Although current retrofit systems reduce children's exposure while waiting to board at a bus station, retrofitting by itself does not protect children satisfactorily from in-cabin particle exposures. Turning on the bus engine increased in-cabin UFP levels significantly only when the wind blew from the bus' tailpipe toward its hood with its windows open. This indicated that wind direction and window position are significant factors determining how much self-released tailpipe emissions may penetrate into the bus cabin. The use of an air purifier was found to remove in-cabin particles by up to 50% which might be an alternative short-to-medium term strategy to protect children's health.

  9. 49 CFR 571.221 - Standard No. 221, School bus body joint strength.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 6 2010-10-01 2010-10-01 false Standard No. 221, School bus body joint strength. 571.221 Section 571.221 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR VEHICLE SAFETY STANDARDS Federal Motor Vehicle Safety Standard...

  10. 49 CFR 571.222 - Standard No. 222; School bus passenger seating and crash protection.

    Science.gov (United States)

    2010-10-01

    ... (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR... school bus occupants against structures within the vehicle during crashes and sudden driving maneuvers... removable without tools or to flip up must have a self-latching mechanism that is activated when a 22-kg (48...

  11. A preliminary survey analysis of school shuttle bus system towards smart mobility solutions

    Science.gov (United States)

    Yue, Wong Seng; Hoy, Cheong Wan; Chye, Koh Keng

    2017-10-01

    Mobility and accessibility are crucial indicators of urban development. Public transport in the urban areas came into existence to fulfil transportation needs as well as mobility and accessibility demands. Ridership can be affected by the quality and quantity of transit service. However, technical improvements are needed for such as real-time bus information, controlling run time and headway delay. Thus, this paper is aimed to carry out a preliminary survey to determine the problems of school shuttle bus that faced by the students in a selected educational institution, their perceptions of using shuttle bus tracking and information mobile application and impacts of real-time information of public transits on bus ridership and towards smart mobility solutions. Efficient public transportation system needs further investigation about the role of mobile application for the bus tracking system in supporting smart mobility actions and real-time information. The proposed application also provides a smart solution for the management of public infrastructures and urban facilities in Malaysia in future. Eventually, this study opens an opportunity to improve Malaysian quality of life on the public value that created for the city as a whole.

  12. GeoBus: bringing Earth science learning to secondary schools in the UK

    Science.gov (United States)

    Robinson, Ruth; Roper, Kathryn; Pike, Charlotte

    2015-04-01

    GeoBus (www.geobus.org.uk) is an educational outreach project that was developed in 2012 by the Department of Earth and Environmental Sciences at the University of St Andrews, and it is sponsored jointly by industry and the UK Research Councils (NERC and EPSRC). The aims of GeoBus are to support the teaching of Earth Science in secondary (middle and high) schools by providing teaching support to schools that have no or little expertise of teaching Earth science, to share the outcomes of new science research and the experiences of young researchers with school pupils, and to provide a bridge between industry, higher education institutions, research councils and schools. Since its launch, GeoBus has visited over 160 different schools across the length and breadth of Scotland. Almost 35,000 pupils will have been involved in experiential Earth science learning activities by April 2015, including many in remote and disadvantaged regions. The challenge with secondary school experiential learning as outreach is that activities need to be completed in either 50 or 80 minutes to fit within the school timetables in the UK, and this can limit the amount of hands-on activities that pupils undertake in one session. However, it is possible to dedicate a whole or half day of linked activities to Earth science learning within the Scotland Curriculum for Excellence, and this provides a long enough period to undertake field work, conduct group projects, or complete more complicated experiments. GeoBus has developed a suite of workshops that all involve experiential learning and are targeted for shorter and longer time slots, and the lessons learned in developing and refining these workshops to maximise the learning achieved will be presented. A key aim of GeoBus is to incorporate research outcomes directly into workshops, and to involve early career researchers in project development. One example that is currently in progress is a set of hydrology workshops that focus on the water

  13. A Rule-Based Energy Management Strategy for a Plug-in Hybrid School Bus Based on a Controller Area Network Bus

    Directory of Open Access Journals (Sweden)

    Jiankun Peng

    2015-06-01

    Full Text Available This paper presents a rule-based energy management strategy for a plug-in hybrid school bus (PHSB. In order to verify the effectiveness and rationality of the proposed energy management strategy, the powertrain and control models were built with MATLAB/Simulink. The PHSB powertrain model includes an engine model, ISG (integrated started and generator model, drive motor model, power battery packs model, driver model, and vehicle longitudinal dynamics model. To evaluate the controller area network (CAN bus performance features such as the bus load, signal hysteresis, and to verify the reliability and real-time performance of the CAN bus multi-node control method, a co-simulation platform was built with CANoe and MATLAB/Simulink. The co-simulation results show that the control strategy can meet the requirements of the PHSB’s dynamic performance. Meanwhile, the charge-depleting mode (CD and charge-sustaining mode (CS can switch between each other and maintain a state-of-charge (SoC of around 30%, indicating that the energy management strategy effectively extends the working period of the CD mode and improves the fuel economy further. The energy consumption per 100 km includes 13.7 L diesel and 10.5 kW·h electricity with an initial SoC of 75%. The CANoe simulation results show that the bus communication performs well without error frames.

  14. GeoBus: bringing experiential Earth science learning to secondary schools in the UK

    Science.gov (United States)

    Pike, C. J.; Robinson, R. A. J.; Roper, K. A.

    2014-12-01

    GeoBus (www.geobus.org.uk) is an educational outreach project that was developed in 2012 by the Department of Earth and Environmental Sciences at the University of St Andrews, and it is sponsored jointly by industry and the UK Research Councils (NERC and EPSRC). The aims of GeoBus are to support the teaching of Earth Science in secondary (middle and high) schools by providing teaching support to schools that have no or little expertise of teaching Earth science, to share the outcomes of new science research and the experiences of young researchers with school pupils, and to provide a bridge between industry, higher education institutions, research councils and schools. Since its launch, GeoBus has visited over 160 different schools across the length and breadth of Scotland. Over 30,000 pupils will have been involved in experiential Earth science learning activities by December 2014, including many in remote and disadvantaged regions. The challenge with secondary school experiential learning as outreach is that activities need to be completed in either 50 or 80 minutes to fit within the school timetables in the UK, and this can limit the amount of hands-on activities that pupils undertake in one session. However, it is possible to dedicate a whole or half day of linked activities to Earth science learning in Scotland and this provides a long enough period to undertake field work, conduct group projects, or complete more complicated experiments. GeoBus has developed a suite of workshops that all involve experiential learning and are targeted for shorter and longer time slots, and the lessons learned in developing and refining these workshops to maximise the learning achieved will be presented. Three potentially unsurprising observations hold true for all the schools that GeoBus visits: young learners like to experiment and use unfamiliar equipment to make measurements, the element of competition stimulates learners to ask questions and maintain focus and enthusiasum

  15. The School Bus Symposium: A Poetic Journey of Co-created Conference Space

    Directory of Open Access Journals (Sweden)

    Mitchell A McLarnon

    2016-07-01

    Full Text Available With the intention of disrupting and re-imagining traditional conference spaces, this article is a poetic compilation developed from a Curriculum Studies conference symposium that took place on a school bus. During the School Bus Symposium, in situ poetry writing and reading, song and storytelling occurred in response to open ended prompts and facilitation of creative activities. After the symposium, a call was issued to invite participants to submit any poetry or stories produced during, or inspired by the session. Consisting of 18 submissions including poetry, story, photography and creative essays, infused by curriculum theory and poetic inquiry, this collection offers an inclusive, reflective, participatory, and experiential rendering where participants are living and journeying poetically. Emphasizing creative engagement with personal memories, the authors collectively aimed to promote art education through imaginative approaches to curriculum studies, poetic inquiry and academic conferences.

  16. Cost-effectiveness of active transport for primary school children - Walking School Bus program

    Directory of Open Access Journals (Sweden)

    Swinburn Boyd

    2009-09-01

    Full Text Available Abstract Background To assess from a societal perspective the incremental cost-effectiveness of the Walking School Bus (WSB program for Australian primary school children as an obesity prevention measure. The intervention was modelled as part of the ACE-Obesity study, which evaluated, using consistent methods, thirteen interventions targeting unhealthy weight gain in Australian children and adolescents. Methods A logic pathway was used to model the effects on body mass index [BMI] and disability-adjusted life years [DALYs] of the Victorian WSB program if applied throughout Australia. Cost offsets and DALY benefits were modelled until the eligible cohort reached 100 years of age or death. The reference year was 2001. Second stage filter criteria ('equity', 'strength of evidence', 'acceptability', feasibility', sustainability' and 'side-effects' were assessed to incorporate additional factors that impact on resource allocation decisions. Results The modelled intervention reached 7,840 children aged 5 to 7 years and cost $AUD22.8M ($16.6M; $30.9M. This resulted in an incremental saving of 30 DALYs (7:104 and a net cost per DALY saved of $AUD0.76M ($0.23M; $3.32M. The evidence base was judged as 'weak' as there are no data available documenting the increase in the number of children walking due to the intervention. The high costs of the current approach may limit sustainability. Conclusion Under current modelling assumptions, the WSB program is not an effective or cost-effective measure to reduce childhood obesity. The attribution of some costs to non-obesity objectives (reduced traffic congestion and air pollution etc. is justified to emphasise the other possible benefits. The program's cost-effectiveness would be improved by more comprehensive implementation within current infrastructure arrangements. The importance of active transport to school suggests that improvements in WSB or its variants need to be developed and fully evaluated.

  17. Cost-effectiveness of active transport for primary school children - Walking School Bus program.

    Science.gov (United States)

    Moodie, Marjory; Haby, Michelle; Galvin, Leah; Swinburn, Boyd; Carter, Robert

    2009-09-14

    To assess from a societal perspective the incremental cost-effectiveness of the Walking School Bus (WSB) program for Australian primary school children as an obesity prevention measure. The intervention was modelled as part of the ACE-Obesity study, which evaluated, using consistent methods, thirteen interventions targeting unhealthy weight gain in Australian children and adolescents. A logic pathway was used to model the effects on body mass index [BMI] and disability-adjusted life years [DALYs] of the Victorian WSB program if applied throughout Australia. Cost offsets and DALY benefits were modelled until the eligible cohort reached 100 years of age or death. The reference year was 2001. Second stage filter criteria ('equity', 'strength of evidence', 'acceptability', feasibility', sustainability' and 'side-effects') were assessed to incorporate additional factors that impact on resource allocation decisions. The modelled intervention reached 7,840 children aged 5 to 7 years and cost $AUD22.8M ($16.6M; $30.9M). This resulted in an incremental saving of 30 DALYs (7:104) and a net cost per DALY saved of $AUD0.76M ($0.23M; $3.32M). The evidence base was judged as 'weak' as there are no data available documenting the increase in the number of children walking due to the intervention. The high costs of the current approach may limit sustainability. Under current modelling assumptions, the WSB program is not an effective or cost-effective measure to reduce childhood obesity. The attribution of some costs to non-obesity objectives (reduced traffic congestion and air pollution etc.) is justified to emphasise the other possible benefits. The program's cost-effectiveness would be improved by more comprehensive implementation within current infrastructure arrangements. The importance of active transport to school suggests that improvements in WSB or its variants need to be developed and fully evaluated.

  18. School bus travel is associated with bullying victimization among Canadian male, but not female, middle and high school students.

    Science.gov (United States)

    Sampasa-Kanyinga, Hugues; Chaput, Jean-Philippe; Hamilton, Hayley A; Larouche, Richard

    2016-08-01

    Previous research has found a link between active school transportation and bullying victimization among school-aged children. However, the link with other school travel modes (such as car, school bus, and public transportation) and bullying victimization is largely unknown. The purpose of this study was to investigate the association between school travel mode and report of bullying victimization among Canadian middle and high school students. The sample consisted of 5065 students aged 11-20 years (mean age: 15.2±1.9 years; 56% females) who participated in the 2013 Ontario Students Drug Use and Health Survey (OSDUHS). Overall, 24.7% of students reported school bullying victimization in the past year. Females (27.2%) were more likely than males (22.3%) to be victims of school bullying (ptravel to (adjusted odd ratio (OR)=1.83; 95% confidence interval (CI)=1.25-2.68) and from (OR=1.79; 95% CI=1.70-2.67) school was associated with greater odds of bullying victimization among males, but not females. However, the use of public transportation to get to school was associated with lower odds of bullying victimization compared to active transportation among females only (OR=0.59; 95% CI=0.36-0.97). These findings suggest that school travel mode should be considered when considering risks for bullying victimization. Bullying prevention efforts should target school buses to make children's commute a safe and enjoyable experience. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. The volume and type of unhealthy bus shelter advertising around schools in Perth, Western Australia: Results from an explorative study.

    Science.gov (United States)

    Parnell, Ashleigh; Edmunds, Melinda; Pierce, Hannah; Stoneham, Melissa J

    2018-03-05

    Exposure to advertising for unhealthy food, alcohol and gambling has been shown to influence children and adolescents' behaviours and attitudes. This exploratory study aimed to assess the volume and type of unhealthy bus shelter advertisements near schools in five local government areas in Perth, Western Australia and to monitor whether the volume of unhealthy advertisements varied seasonally. The 29 local governments in the Perth metropolitan region were contacted seeking information regarding the locations of bus shelters featuring advertisements in their local government area. Five local governments provided sufficient information for an audit of the bus shelter advertisements in their area to be conducted. Every bus shelter within 500 m of a school was photographed and the type of advertisement recorded. The advertisements in the food, non-alcoholic beverage, alcohol, or gambling categories were then classified as being healthy, moderate, or unhealthy. This process was carried out in June, September, December 2016, and March 2017 to ascertain whether the type of advertisements displayed changed depending on the season. Of the 293 advertisements recorded over the four audits, 31% featured unhealthy products, 3% moderate, and <1% healthy. Only two of the 293 advertisements were classified as being healthy. Seasonal variation in the volume of unhealthy advertisements was not identified. SO WHAT?: Western Australian school students are regularly exposed to unhealthy bus shelter advertisements. Stricter regulation of outdoor advertising is needed to ensure that young people are protected from the influence of unhealthy industries. © 2018 Australian Health Promotion Association.

  20. Free riders play fair

    OpenAIRE

    Takikawa, Hirohide

    2012-01-01

    After the demise of the social contract theory, the argument from fair play, which employs the principle of fair play, has been widely acknowledged as one of the most promising ways of justifying political obligation. First, I articulate the most promising version of the principle of fair play. Then, I show that free riders play fair, that is, that their moral fault lies not in unfairness but in the violation of a rule by appealing to the example of three-in-a-boat. Finally, I conclude that e...

  1. Story Corner: Freedom Riders

    Science.gov (United States)

    Brownstein, Rhonda

    2009-01-01

    These days, when people want to travel a long way, they take an airplane. But once, not so long ago really, only rich people flew in airplanes. Most people took a train or a bus. Back then, in the Montgomery Greyhound station, one could notice a bricked-up doorway that was once an open door with a sign above it that said "Colored…

  2. The GeoBus project: a mobile Earth science outreach project for secondary schools in the UK

    Science.gov (United States)

    Robinson, R. A.; Roper, K. A.; Macfarlane, D.; Pike, C.

    2013-12-01

    GeoBus is an educational outreach project that was developed in 2012 by the Department of Earth and Environmental Sciences at the University of St Andrews. It is sponsored jointly by industry and the UK Research Councils (NERC and EPSRC). The aims of GeoBus are to support the teaching of Earth Science in secondary (high) schools by providing teaching resources that are not readily available to educators, to inspire young learners by incorporating new science research outcomes in teaching activities, and to provide a bridge between industry, higher education institutions, research councils and schools. These linkages are important for introducing career opportunities in Earth sciences. Since its launch, GeoBus has visited over 140 different schools across the length and breadth of Scotland. Over 20,000 pupils will have been involved in practical hands-on Earth science learning activities by December 2013, including many in remote and disadvantaged regions. The resources that GeoBus brings to schools include all the materials and equipment needed to run workshops, field excursions and Enterprise Challenges. GeoBus provides 16 workshops which can be adapted for different learning levels. Workshops are 50 to 80 minute sessions for up to 30 pupils and topics include minerals, rocks, fossils, geological time, natural resources, climate change, volcanoes, earthquakes, and geological mapping. As with all GeoBus activities, the inclusion of equipment and technology otherwise unavailable to schools substantially increases the engagement of pupils in workshops. Field excursions are popular, as many teachers have little or no field trainng and feel unable to lead this type of activity. The excursions comprise half or full day sessions for up to 30 pupils and are tailored to cover the local geology or geomorphology. The Enterprise Challenges are half or full day sessions for up to 100 pupils. Current topics are Drilling for Oil, Renewable Energy, a Journey to Mars and Scotland

  3. The mobile GeoBus outreach project: hands-on Earth and Mars activities for secondary schools in the UK

    Science.gov (United States)

    Robinson, Ruth; Pike, Charlotte; Roper, Kathryn

    2015-04-01

    GeoBus (www.geobus.org.uk) is an educational outreach project that was developed in 2012 by the Department of Earth and Environmental Sciences at the University of St Andrews, and it is sponsored jointly by industry and the UK Research Councils (NERC and EPSRC). The aims of GeoBus are to support the teaching of Earth Science in secondary schools by providing teaching resources that are not readily available to educators, to inspire young learners by incorporating new science research outcomes in teaching activities, and to provide a bridge between industry, higher education institutions, research councils and schools. Since its launch, GeoBus has visited over 160 different schools across the length and breadth of Scotland. Just under 35,000 pupils have been involved in practical hands-on Earth science learning activities since the project began in 2012, including many in remote and disadvantaged regions. The resources that GeoBus brings to schools include all the materials and equipment needed to run 50 - 80 minute workshops, and half- or whole-day Enterprise Challenges and field excursions. Workshops are aimed at a class of up to 30 pupils and topics include minerals, rocks, fossils, geological time, natural resources, climate change, volcanoes, earthquakes, and geological mapping. As with all GeoBus activities, the inclusion of equipment and technology otherwise unavailable to schools substantially increases the engagement of pupils in workshops. Field excursions are increasingly popular, as many teachers have little or no field trainng and feel unable to lead this type of activity. The excursions comprise half or full day sessions for up to 30 pupils and are tailored to cover the local geology or geomorphology. Enterprise Challenge are half or full day sessions for up to 100 pupils. Topics include "Journey to Mars", "Scotland's Rocks", "Drilling for Oil", and "Renewable Energy". Both of the energy Enterprise Challenges were designed to incorporates ideas and

  4. Creative Bus Financing.

    Science.gov (United States)

    Malone, Wade

    1982-01-01

    Alternative ways of financing school bus purchases include financing privately through contractors or commercial banks, financing through sources such as insurance companies and pension funds, leasing the buses, or contracting for transportation services. (Author/MLF)

  5. Highway/Railroad Accident Report: Collision Of Northeast Illinois Regional Commuter Railroad Corporation (METRA) Train And Transportation Joint Agreement School District 47/155 School Bus At Railroad/Highway Grade Crossing In Fox River Grove, Illinois, On

    Science.gov (United States)

    1996-10-29

    This report explains the collision of a Northeast Illinois Regional Commuter Railroad Corporation commuter train with a Transportation Joint Agreement School District 47/155 school bus that was stopped at a railroad/highway grade crossing in Fox Rive...

  6. Reducing Children's Exposure to School Bus Diesel Exhaust in One School District in North Carolina

    Science.gov (United States)

    Mazer, Mary E.; Jacobson Vann, Julie C.; Lamanna, Beth F.; Davison, Jean

    2014-01-01

    Children who are exposed to diesel exhaust from idling school buses are at increased risk of asthma exacerbation, decreased lung function, immunologic reactions, leukemia, and increased susceptibility to infections. Policies and initiatives that aim to protect school children from the harmful effects of exposure to diesel exhaust range from…

  7. Research on Demand for Bus Transport and Transport Habits of High School Students in Žilina Region

    Directory of Open Access Journals (Sweden)

    Konečný Vladimír

    2017-11-01

    Full Text Available The paper deals with the analysis of demand for bus transport to examine determinants of demand and practices of high school students based on survey of their transport habits in Žilina Region. Transport habits of students are individual and variable in time. This group of passengers is dependent on public passenger transport services because of their travelling to schools. Significant part of demand for public passenger transport is also formed by this this group of passengers. The knowledge of student's transport habits may help in process of adaptation of offering and quality of transport serviceability what may subsequently stabilize demand for public passenger transport.

  8. Testing the effects of safety climate and disruptive children behavior on school bus drivers performance: A multilevel model.

    Science.gov (United States)

    Zohar, Dov; Lee, Jin

    2016-10-01

    The study was designed to test a multilevel path model whose variables exert opposing effects on school bus drivers' performance. Whereas departmental safety climate was expected to improve driving safety, the opposite was true for in-vehicle disruptive children behavior. The driving safety path in this model consists of increasing risk-taking practices starting with safety shortcuts leading to rule violations and to near-miss events. The study used a sample of 474 school bus drivers in rural areas, driving children to school and school-related activities. Newly developed scales for measuring predictor, mediator and outcome variables were validated with video data taken from inner and outer cameras, which were installed in 29 buses. Results partially supported the model by indicating that group-level safety climate and individual-level children distraction exerted opposite effects on the driving safety path. Furthermore, as hypothesized, children disruption moderated the strength of the safety rule violation-near miss relationship, resulting in greater strength under high disruptiveness. At the same time, the hypothesized interaction between the two predictor variables was not supported. Theoretical and practical implications for studying safety climate in general and distracted driving in particular for professional drivers are discussed. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. School buses, air pollution and children's health : improving children's health and local air quality by reducing school bus emissions

    Energy Technology Data Exchange (ETDEWEB)

    Perrotta, K. [Ontario Public Health Association, Toronto, ON (Canada)

    2005-11-01

    The exhaust gases from school buses was examined and recommendations were presented for the establishment of a healthy school bus program in Ontario that is directed at improving children's health and local air quality. The Ontario Public Health Association is concerned with school bus emissions because they are heavy-duty vehicles that emit large quantities of diesel-related air pollutants such as fine particulate matter, nitrogen oxides and diesel particulates. In addition, school buses can be self-polluting vehicles that expose children on-board to high levels of fine particulates and diesel particulate matter. Both these pollutants have been associated with a range of acute and chronic health problems such as asthma, respiratory infections, allergies, and school absences. With nearly 800,000 Ontario children being transported on school buses annually, these exposures can represent a serious public health concern, as childhood exposures can also influence the health of exposed individuals later in life. Exposure studies have found that tailpipe and engine emissions contribute greatly to concentrations of air pollutants on-board school buses. The studies also showed that on-board concentrations were also influenced by local air quality in the communities studied, traffic density, wind direction, the configuration of windows, idling and queuing patterns. It was recommended that the use of ultra-low sulphur diesel fuel along with the installation of diesel particulate filters and closed crankcase filters can reduce the concentrations of air pollutants on-board school buses to almost ambient air levels, even under idling conditions. This report recommended the replacement of pre-1994 school buses, the retrofitting of 1994-2003 school buses with filters, and maintaining proper maintenance, idling and vehicle operation practices. refs., tabs., figs.

  10. Wait for the Bus: How Lowcountry School Site Selection and Design Deter Walking to School and Contribute to Urban Sprawl.

    Science.gov (United States)

    Kouri, Christopher

    This paper presents a study on how the South Carolina school site selection process can affect the quality of the students' experience and access to their schools. Focusing on students options for getting to school, e.g., hazards that prevent students from walking to school and the size of school sites that place schools on the edge of…

  11. Distributed Transit Rider Messaging : Final Project Report

    Science.gov (United States)

    2013-12-01

    Uncertainty, lack of transit system awareness, and feelings of isolation have negative impact on all riders, regardless of abilities, thereby reducing community livability and transit demand. Lower transit demand, in turn, decreases economic competit...

  12. 75 FR 66686 - Federal Motor Vehicle Safety Standards; Seat Belt Assembly Anchorages, School Bus Passenger...

    Science.gov (United States)

    2010-10-29

    ... loose belts) also applies to seats that have wheelchair positions or side emergency doors behind them... have wheelchair positions or side emergency doors behind them); and, the test requirements for self... which correspond to the size of some high school football players) and school buses closer in weight to...

  13. The Bus Stops Here: The Case for Biodiesel in School Buses.

    Science.gov (United States)

    Rao, Steven T.

    2002-01-01

    Suggests that diesel exhaust from most of the nation's school buses may be hazardous to children's health. Documents studies on the nature and potential magnitude of the risk to children and proposes replacing petroleum diesel with biodiesel as the fuel for school buses. Presents the merits and practicality of switching to biodiesel as a healthier…

  14. Bus basics

    International Nuclear Information System (INIS)

    Dobinson, R.W.

    1983-01-01

    The aims of this course are: 1. To introduce the general concepts of buses used to interconnect processors, perpherals, and instrumentation. 2. To classify, albeit crudely, different types of bus systems. 3. To give some examples of past, present, and future buses as applied to the field of high-energy physics, including some details of software. 4. To provide references for further study. (orig.)

  15. Method for in-use measurement and evaluation of the activity, fuel use, electricity use, and emissions of a plug-in hybrid diesel-electric school bus.

    Science.gov (United States)

    Choi, Hyung-Wook; Frey, H Christopher

    2010-05-01

    The purpose of this study is to demonstrate a methodology for characterizing at high resolution the energy use and emissions of a plug-in parallel-hybrid diesel-electric school bus (PHSB) to support assessments of sensitivity to driving cycles and comparisons to a conventional diesel school bus (CDSB). Data were collected using onboard instruments for a first-of-a-kind prototype PHSB and a CDSB of the same chassis and engine, operated on actual school bus routes. The engine load was estimated on the basis of vehicle specific power (VSP) and an empirically derived relationship between VSP and engine manifold absolute pressure (MAP). VSP depends on speed, acceleration, and road grade. For the PHSB, the observed electrical discharge or recharge to the traction motor battery was characterized on the basis of VSP. The energy use and emission rates of the PHSB from tailpipe and electricity use were estimated for five real-world driving cycles and compared to the engine fuel use and emissions of the CDSB. The PHSB had the greatest advantage on arterial routes and less advantage on highway or local routes. The coupled VSP-MAP modeling approach enables assessment of a wide variety of driving conditions and comparisons of vehicles with different propulsion technologies.

  16. Public perception related to a hydrogen hybrid internal combustion engine transit bus demonstration and hydrogen fuel

    International Nuclear Information System (INIS)

    Hickson, Allister; Phillips, Al; Morales, Gene

    2007-01-01

    Hydrogen has been widely considered as a potentially viable alternative to fossil fuels for use in transportation. In addition to price competitiveness with fossil fuels, a key to its adoption will be public perceptions of hydrogen technologies and hydrogen fuel. This paper examines public perceptions of riders of a hydrogen hybrid internal combustion engine bus and hydrogen as a fuel source

  17. Vulnerability of motorcycle riders and co-riders to injuries in multi-occupant crashes.

    Science.gov (United States)

    Oluwadiya, Kehinde Sunday; Ojo, Owolabi Dele; Adegbehingbe, Olayinka Oladiran; Mock, Charles; Popoola, Ogunsuyi Sunday

    2016-01-01

    In developing countries, most motorcycles are ridden with more than one occupant. The objective of this study was to establish the relative vulnerability of riders and co-riders to injury and determine the injury risk factors in multi-occupant motorcycle crashes. Between January and December 2010, we collected crash and injury data from victims of multi-occupant motorcycle. It is a hospital-based study. The probability of sustaining injuries was similar for co-riders and riders, but co-riders were more likely to sustain severe injuries. Occupants of >2-occupant motorcycles were also more likely to be involved in risky behaviours like not wearing helmet and speeding than those on 2-occupant motorcycles. Occupants of motorcycles on which there were more than two occupants were at an increased risk of sustaining injuries compared with occupants of motorcycles with only two occupants (OR: 2.1, 95% CI: 1.1-4.3). Motorcycle co-riders were more vulnerable to severe injuries than riders. The significance of the study finding to prevention was discussed.

  18. (Boda boda) riders in Bungoma Town, Kenya

    African Journals Online (AJOL)

    Even stationary bikes can cause trauma to the blood supply to the penis, resulting in Erectile Dysfunction. Objective: To evaluate the effects of long term bicycle riding on erectile function among bicycle taxi (bodaboda) riders in Bungoma town. Design: A cross-sectional comparative study. Setting: Bungoma County, Kenya.

  19. 19 CFR 113.24 - Riders.

    Science.gov (United States)

    2010-04-01

    ... bond may be used only when the change in name does not change the legal identity or status of the... deletion of trade names and unincorporated divisions of a corporate principal. A bond rider may be used to add to or delete from a bond trade names and the names of unincorporated divisions of a corporate...

  20. The relationship between Motorcycle Rider Behaviour Questionnaire scores and crashes for riders in Australia.

    Science.gov (United States)

    Stephens, A N; Brown, J; de Rome, L; Baldock, M R J; Fernandes, R; Fitzharris, M

    2017-05-01

    Motorcycle riders are over-represented in road fatalities in Australia. While riders represent 18% of the road users killed each year, motorcycle registrations constitute only 4.5% of the registered vehicle fleet. The Motorcycle Rider Behaviour Questionnaire (MRBQ) was developed with a view toward understanding behaviours likely to be associated with crash risk. These include behaviours that are either intentional (such as violations of road and speed regulations and stunts) or unintentional (such as errors relating to traffic or control of the motorcycle), as well as protective behaviours related to use of safety equipment. The dual aims of the current study were, first, to determine the appropriate structure of a modified version of the MRBQ for use in a representative sample of riders in Australia and, second, to understand which MRBQ factors are associated with crash involvement. A stratified sampling procedure was undertaken to ensure the socio-economic status of local government area, age and gender of the sample was representative of the broader population of riders in New South Wales, Australia. The sample consisted of 470 riders (males=89%). Exploratory factor analysis revealed a 29-item, five factor structure was suitable on the Australian data encompassing traffic errors, speed violations, protective gear, control errors and stunts. Overall, riders reported relatively safe behaviours, with frequent use of protective gear and infrequent aberrant behaviours. However, even though infrequent, violations of speed and errors related to control of the motorcycle increased the odds of near-crash involvement, whilst stunt behaviours were associated with increased odds of crash involvement. Interventions and countermeasures need to target these specific behaviours. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. An investigation into the effects of traditional neuromuscular training Vs rider specific training on novice rider position

    OpenAIRE

    Boden, Eleanor

    2013-01-01

    The equine industry and within it, the competition rider community, is increasingly acknowledging that rider strength and fitness is vital in achieving the best results in competition. The sport of horse riding is described as unique in its posture and motion patterns and cannot be easily be compared to the actions of any other athletic endeavour. There are several factors that cause a horse to not move correctly, the most common being an unbalanced rider. Other sporting disciplines are mo...

  2. GO Bus impact analysis.

    Science.gov (United States)

    2013-08-01

    NJ TRANSIT launched two relatively new enhanced bus services: GO 25 serving the : Springfield Avenue corridor in 2008 and GO 28 serving the Bloomfield Avenue corridor in 2009. : As an enhanced but not full Bus Rapid Transit (BRT) service, GO Bus feat...

  3. Punishing second-order free riders before first-order free riders: The effect of pool punishment priority on cooperation

    OpenAIRE

    Ozono, Hiroki; Kamijo, Yoshio; Shimizu, Kazumi

    2017-01-01

    Second-order free riders, who do not owe punishment cost to first-order free riders in public goods games, lead to low cooperation. Previous studies suggest that for stable cooperation, it is critical to have a pool punishment system with second-order punishment, which gathers resources from group members and punishes second-order free riders as well as first-order free riders. In this study, we focus on the priority of punishment. We hypothesize that the pool punishment system that prioritiz...

  4. Intelligent Bus Stops in the Flexible Bus Systems

    OpenAIRE

    Razi Iqbal; Muhammad Usman Ghani

    2014-01-01

    The purpose of this paper is to discuss Intelligent Bus Stops in a special Demand Responsive Transit (DRT), the Flexible Bus System. These Intelligent Bus Stops are more efficient and information rich than Traditional Bus Stops. The real time synchronization of the Flexible Bus System makes it unique as compared to Traditional Bus Systems. The Main concern is to make Bus Stops intelligent and information rich. Buses are informed about the no. of passengers waiting at the upcoming ...

  5. Micro-Doppler classification of riders and riderless horses

    Science.gov (United States)

    Tahmoush, David

    2014-05-01

    Micro-range Micro-Doppler can be used to isolate particular parts of the radar signature, and in this case we demonstrate the differences in the signature between a walking horse versus a walking horse with a rider. Using micro-range micro-Doppler, we can distinguish the radar returns from the rider as separate from the radar returns of the horse.

  6. Young moped riders : reducing high risks and high insurance premiums.

    NARCIS (Netherlands)

    Wegman, F.C.M.

    1992-01-01

    The paper examines the reported fall in fatal accidents for moped riders in The Netherlands, and also describes developments with respect to the ownership and use of mopeds. An analysis considers the safety problems of moped riders and suggests how insurance companies might help overcome the safety

  7. Estimating bus passenger waiting times from incomplete bus arrivals data

    OpenAIRE

    McLeod, F.N.

    2007-01-01

    This paper considers the problem of estimating bus passenger waiting times at bus stops using incomplete bus arrivals data. This is of importance to bus operators and regulators as passenger waiting time is a key performance measure. Average waiting times are usually estimated from bus headways, that is, time gaps between buses. It is both time-consuming and expensive to measure bus arrival times manually so methods using automatic vehicle location systems are attractive; however, these syste...

  8. Intelligent Bus Stops in the Flexible Bus Systems

    Directory of Open Access Journals (Sweden)

    Razi Iqbal

    2014-09-01

    Full Text Available The purpose of this paper is to discuss Intelligent Bus Stops in a special Demand Responsive Transit (DRT, the Flexible Bus System. These Intelligent Bus Stops are more efficient and information rich than Traditional Bus Stops. The real time synchronization of the Flexible Bus System makes it unique as compared to Traditional Bus Systems. The Main concern is to make Bus Stops intelligent and information rich. Buses are informed about the no. of passengers waiting at the upcoming Bus Stops. If there are no passengers to ride or get off on upcoming Bus Stop, the Bus can skip that Bus Stop and head towards the next Bus Stop where passenger is waiting, which will decrease the ride time of the passengers on the Bus and also the wait time of the passengers waiting on the upcoming Bus Stops. Providing more information at Bus Stops about the Destination (Time to Destination, Distance to Destination etc. and Buses (Bus Location, Arrival Time of Bus etc. makes it easier for the passengers to decide whether to ride a particular Bus or not.

  9. TPG bus passes

    CERN Multimedia

    Staff Association

    2013-01-01

    The CERN Staff Association will stop selling TPG bus passes. All active and retired members of the CERN personnel will be able to purchase Unireso bus passes from the CERN Hostel - Building 39 (Meyrin site) from 1st February 2013. For more information: https://cds.cern.ch/journal/CERNBulletin/2013/04/Announcements/1505279?ln=en

  10. Analysis of local bus markets : volume II – rider characteristics : final report.

    Science.gov (United States)

    2017-07-04

    Despite having an extensive network of public transit, traffic congestion and transportation-related greenhouse gas (GHG) emissions are significant concerns in New Jersey. This research hypothesizes that traffic congestion and air quality concerns in...

  11. The erigone bus study

    International Nuclear Information System (INIS)

    Durieu, L.; Vignes, M.; Wolstenholme, P.

    1982-01-01

    A study has been made of some factors determining the performance and cost-effectiveness of microcomputer bus systems implemented in Europa crates. An experimental system has been specified and a number of modules constructed in accordance with the specification, in order to test the validity of some of the ideas proposed. It has been demonstrated that the bus interfacing logic can be simple and inexpensive, while maintaining a high degree of processor independence and also a high degree of transparency in operation. The number of pins required by the bus is minimized by multiplexing address and data. A series termination for the drive of the multiplexed lines permits cross-talk to be reduced to insignificant levels: this technique is recommended for wider application. The experimental bus is proposed as a basis for the construction of simple microcomputer-based instrumentation systems. (orig.)

  12. SPFC bus design studies

    Energy Technology Data Exchange (ETDEWEB)

    Potter, L.; Reinkingh, J.

    1999-07-01

    This report presents the results of a study assessing the design options for a solid polymer fuel cell bus. Commercial and operation requirements, environmental and market drivers, and fuel processor modeling are examined. Power train specifications and detailed system design are investigated covering fuel cell system dynamic response, hybrid system size, fuel cell system start-up time, system specifications, and hybrid bus component dimensions and costs. (UK)

  13. Risk factors affecting fatal bus accident severity: Their impact on different types of bus drivers.

    Science.gov (United States)

    Feng, Shumin; Li, Zhenning; Ci, Yusheng; Zhang, Guohui

    2016-01-01

    While the bus is generally considered to be a relatively safe means of transportation, the property losses and casualties caused by bus accidents, especially fatal ones, are far from negligible. The reasons for a driver to incur fatalities are different in each case, and it is essential to discover the underlying risk factors of bus fatality severity for different types of drivers in order to improve bus safety. The current study investigates the underlying risk factors of fatal bus accident severity to different types of drivers in the U.S. by estimating an ordered logistic model. Data for the analysis are retrieved from the Buses Involved in Fatal Accidents (BIFA) database from the USA for the years 2006-2010. Accidents are divided into three levels by counting their equivalent fatalities, and the drivers are classified into three clusters by the K-means cluster analysis. The analysis shows that some risk factors have the same impact on different types of drivers, they are: (a) season; (b) day of week; (c) time period; (d) number of vehicles involved; (e) land use; (f) manner of collision; (g) speed limit; (h) snow or ice surface condition; (i) school bus; (j) bus type and seating capacity; (k) driver's age; (l) driver's gender; (m) risky behaviors; and (n) restraint system. Results also show that some risk factors only have impact on the "young and elder drivers with history of traffic violations", they are: (a) section type; (b) number of lanes per direction; (c) roadway profile; (d) wet road surface; and (e) cyclist-bus accident. Notably, history of traffic violations has different impact on different types of bus drivers. Copyright © 2015 Elsevier Ltd. All rights reserved.

  14. Savannah River bus project

    Energy Technology Data Exchange (ETDEWEB)

    Summers, W.A. [Westinghouse Savannah River Co., Aiken, SC (United States)

    1998-08-01

    The H2Fuel Bus is the world`s first hybrid hydrogen electric transit bus. It was developed through a public/private partnership involving several leading technology and industrial organizations in the Southeast, with primary funding and program management provided by the Department of Energy. The primary goals of the project are to gain valuable information on the technical readiness and economic viability of hydrogen buses and to enhance the public awareness and acceptance of emerging hydrogen technologies. The bus has been operated by the transit agency in Augusta, Georgia since April, 1997. It employs a hybrid IC engine/battery/electric drive system, with onboard hydrogen fuel storage based on the use of metal hydrides. Initial operating results have demonstrated an overall energy efficiency (miles per Btu) of twice that of a similar diesel-fueled bus and an operating range twice that of an all-battery powered electric bus. Tailpipe emissions are negligible, with NOx less than 0.2 ppm. Permitting, liability and insurance issues were addressed on the basis of extensive risk assessment and safety analyses, with the inherent safety characteristic of metal hydride storage playing a major role in minimizing these concerns. Future plans for the bus include continued transit operation and use as a national testbed, with potential modifications to demonstrate other hydrogen technologies, including fuel cells.

  15. LHC on the bus

    CERN Multimedia

    Laëtitia Pedroso

    2010-01-01

    On 15 December, an airport bus will be transformed in the image of CERN. The bus will be seen by the thousands of travellers arriving in Geneva, informing them of the possibility to visit CERN.   Sketch of the bus. The good relationship between Geneva International Airport and CERN started several years ago. In 2004 the airport put advertising space in the arrivals area at CERN's disposal free of charge. Now, starting on 15 December, a 40-foot long bus will display a giant sticker advertisement depicting CERN as it takes passengers over the airport tarmac to their planes. This is no ordinary sticker, and it was no mean task to attach it to the bus. The task of producing and attaching it was entrusted to Geneva-based specialists Mathys SA. With the ski season opening on 15 December, there will be many travellers arriving at the airport, and the bus will be ready to receive them. When one thinks of CERN, the subjects that naturally come to mind are the LHC, the mysteries of the Universe...

  16. PyBus -- A Python Software Bus

    OpenAIRE

    Lavrijsen, W

    2005-01-01

    A software bus, just like its hardware equivalent, allows for the discovery, installation, configuration, loading, unloading, and run-time replacement of software components, as well as channeling of inter-component communication. Python, a popular open-source programming language, encourages a modular design on software written in it, but it offers little or no component functionality. However, the language and its interpreter provide sufficient hooks to implement a thin, integral layer...

  17. Functional Bus Driver-Pupil Passenger Relationships.

    Science.gov (United States)

    Farmer, Ernest

    1987-01-01

    Successful school bus drivers bring much more than mechanical know-how to the job. They develop good rapport with students while acting to bring undesirable student behavior under control. Drivers must also show an interest in students' welfare and have a good sense of humor. (MLH)

  18. Bus fuel consumption model

    Energy Technology Data Exchange (ETDEWEB)

    Zargari, S.A. [Iran Univ. of Science and Technology, Teheran (Iran, Islamic Republic of); Khan, A.M. [Carleton Univ., Ottawa, ON (Canada). Dept. of Civil and Environmental Engineering

    2000-07-01

    The interest in rapid bus transit has increased sharply with the realization that modern metropolitan areas rely on public transit to provide for strong economies and communities. As a prevention tool against traffic congestion, deteriorating air quality and rising greenhouse gas emissions, this study of bus fuel consumption was designed to assist in the planning and management of rapid bus transit. The Australian Road Research Board's (ARRB) Road Fuel Consumption Model was used as a starting point. The estimations required were realized with the help of Newtonian Mechanics. The four states of vehicular traffic were examined: acceleration, cruise, deceleration, and idle. The estimated total power required from the engine to overcome resistance forces, to run vehicle accessories and overcome internal engine friction was calculated. The data for the standard and articulated bus was obtained from OC Transpo in Ottawa. The study permitted the authors to conclude that the estimations for the parameters for power requirements and fuel consumption for heavy duty vehicles are appropriate. The methodology for the estimation of fuel consumption on the Transitway, which is part of the rapid bus transit system, proved adequate. In addition, the methodology was useful to estimate fuel savings resulting from demand management strategies with potential for modal shift. 9 refs., 6 tabs.

  19. Factors contributing to young moped rider accidents in Denmark.

    Science.gov (United States)

    Møller, Mette; Haustein, Sonja

    2016-02-01

    Young road users still constitute a high-risk group with regard to road traffic accidents. The crash rate of a moped is four times greater than that of a motorcycle, and the likelihood of being injured in a road traffic accident is 10-20 times higher among moped riders compared to car drivers. Nevertheless, research on the behaviour and accident involvement of young moped riders remains sparse. Based on analysis of 128 accident protocols, the purpose of this study was to increase knowledge about moped accidents. The study was performed in Denmark involving riders aged 16 or 17. A distinction was made between accident factors related to (1) the road and its surroundings, (2) the vehicle, and (3) the reported behaviour and condition of the road user. Thirteen accident factors were identified with the majority concerning the reported behaviour and condition of the road user. The average number of accident factors assigned per accident was 2.7. Riding speed was assigned in 45% of the accidents which made it the most frequently assigned factor on the part of the moped rider followed by attention errors (42%), a tuned up moped (29%) and position on the road (14%). For the other parties involved, attention error (52%) was the most frequently assigned accident factor. The majority (78%) of the accidents involved road rule breaching on the part of the moped rider. The results indicate that preventive measures should aim to eliminate violations and increase anticipatory skills among moped riders and awareness of mopeds among other road users. Due to their young age the effect of such measures could be enhanced by infrastructural measures facilitating safe interaction between mopeds and other road users. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Predicting the acceptance of advanced rider assistance systems.

    Science.gov (United States)

    Huth, Véronique; Gelau, Christhard

    2013-01-01

    The strong prevalence of human error as a crash causation factor in motorcycle accidents calls for countermeasures that help tackling this issue. Advanced rider assistance systems pursue this goal, providing the riders with support and thus contributing to the prevention of crashes. However, the systems can only enhance riding safety if the riders use them. For this reason, acceptance is a decisive aspect to be considered in the development process of such systems. In order to be able to improve behavioural acceptance, the factors that influence the intention to use the system need to be identified. This paper examines the particularities of motorcycle riding and the characteristics of this user group that should be considered when predicting the acceptance of advanced rider assistance systems. Founded on theories predicting behavioural intention, the acceptance of technologies and the acceptance of driver support systems, a model on the acceptance of advanced rider assistance systems is proposed, including the perceived safety when riding without support, the interface design and the social norm as determinants of the usage intention. Since actual usage cannot be measured in the development stage of the systems, the willingness to have the system installed on the own motorcycle and the willingness to pay for the system are analyzed, constituting relevant conditions that allow for actual usage at a later stage. Its validation with the results from user tests on four advanced rider assistance systems allows confirming the social norm and the interface design as powerful predictors of the acceptance of ARAS, while the extent of perceived safety when riding without support did not have any predictive value in the present study. Copyright © 2012 Elsevier Ltd. All rights reserved.

  1. Motorcycle Area Design and Location: Impacts on the Recreational Experiences of Riders and Nonriders.

    Science.gov (United States)

    Bury, Richard L.; Fillmore, Edgar C.

    This study analyzes some of the psychological and sociological effects of constructing motorcycle riding areas adjacent to fixed-site compgrounds. Findings include rider and camper profiles, self- and camper-perceptions of riders, and preferences and satisfactions of campers and riders concerning the proximity and design of riding areas.…

  2. Learning NServiceBus

    CERN Document Server

    Boike, David

    2013-01-01

    This is a practical tutorial containing hands-on examples for creating a messaging and SOA based service bus.This book is for .NET developers who are looking for ways to overcome problems related to buggy third party web service integrations, codebases that have grown into a big ball of mud, and batch jobs failure.

  3. Directly observed road safety compliance by Motor Cycle Riders ...

    African Journals Online (AJOL)

    Objective: To assess the extent of compliance with road safety regulations by motorcycle riders following a five year road safety campaign in Naivasha town, Kenya. Design: A cross sectional study. Setting: Naivasha town, Nakuru county, Kenya. Results: A total of 9,280 MCs ferrying 13,733 people were observed. Less than ...

  4. Reducing casualties involving young drivers and riders in Europe.

    NARCIS (Netherlands)

    Atchison, L.

    2017-01-01

    Young drivers and riders aged 15-25 are more likely to be killed on Europe’s roads than their older counterparts, despite continued improvements in road safety. Road collisions remain one of the highest external causes of death for young people. The risks are especially high for young males and for

  5. Calibrating the Truax Rough Rider seed drill for restoration plantings

    Science.gov (United States)

    Loren St. John; Brent Cornforth; Boyd Simonson; Dan Ogle; Derek Tilley

    2008-01-01

    The purpose of this technical note is to provide a step-by-step approach to calibrating the Truax Rough Rider range drill, a relatively new, state-of-the-art rangeland drill. To achieve the desired outcome of a seeding project, an important step following proper weed control and seedbed preparation is the calibration of the seeding equipment to ensure the recommended...

  6. Circuit breaker and bus

    International Nuclear Information System (INIS)

    Vogel, H.F.

    1978-01-01

    Two close-open operations are required each pulse cycle at approximately 3 MA with the breaker in series with the burn supply, both forming a leg in parallel with the E-coil and the homopolar. To conduct the 3-MA current, approximately 30 breaker units are connected in parallel. Each unit is equipped with a counterpulse capacitor bank, and the bus for the 30 units is provided with a common saturable reactor core made of strip steel wound around the bus. Oil breakers of a special design are chosen because of their high arc resistance facilitating the current transfer to the homopolar machine and for obtaining precision timing in opening and closing of the contacts. The precision timing is achieved by a shock wave method with the oil serving as hydraulic medium. Each of the parallel breaker units possesses two sets of contacts, a stationary and a transient one. A 1-mΩ resistor in series with the transient contacts of each breaker unit is to improve the current sharing. The bus consists of room temperature copper, stranded and transposed to help provide current equalization under transient conditions

  7. Factors contributing to young moped rider accidents in Denmark

    DEFF Research Database (Denmark)

    Møller, Mette; Haustein, Sonja

    2016-01-01

    Young road users still constitute a high-risk group with regard to road traffic accidents. The crash rate of a moped is four times greater than that of a motorcycle, and the likelihood of being injured in a road traffic accident is 10-20 times higher among moped riders compared to car drivers...... was made between accident factors related to (1) the road and its surroundings, (2) the vehicle, and (3) the reported behaviour and condition of the road user. Thirteen accident factors were identified with the majority concerning the reported behaviour and condition of the road user. The average number...... of accident factors assigned per accident was 2.7. Riding speed was assigned in 45% of the accidents which made it the most frequently assigned factor on the part of the moped rider followed by attention errors (42%), a tuned up moped (29%) and position on the road (14%). For the other parties involved...

  8. Final design proposal: Delta Group-Nood Rider 821(tm)

    Science.gov (United States)

    Pastega, C. B.; Vahey, B. P.; Hoffman, K. W.; Doherty, M. C.; Fay, M. J.; Konesky, A. L.; Lilly, D. C.; Moody, D. J.

    1991-01-01

    The Nood Rider 821 (trademark) twin-engine, prop passenger aircraft is described. It is argued that the aircraft is very economical to operate and maintain, offering competitive advantages in the air travel marketplace. The aircraft was designed to operate in 'Aeroworld', a fictional world where the passengers are ping pong balls and the distances between cites are on the order of thousands of feet.

  9. Patient and impatient punishers of free-riders.

    Science.gov (United States)

    Espín, Antonio M; Brañas-Garza, Pablo; Herrmann, Benedikt; Gamella, Juan F

    2012-12-22

    Costly punishment of cheaters who contribute little or nothing to a cooperating group has been extensively studied, as an effective means to enforce cooperation. The prevailing view is that individuals use punishment to retaliate against transgressions of moral standards such as fairness or equity. However, there is much debate regarding the psychological underpinnings of costly punishment. Some authors suggest that costly punishment must be a product of humans' capacity for reasoning, self-control and long-term planning, whereas others argue that it is the result of an impulsive, present-oriented emotional drive. Here, we explore the inter-temporal preferences of punishers in a multilateral cooperation game and show that both interpretations might be right, as we can identify two different types of punishment: punishment of free-riders by cooperators, which is predicted by patience (future orientation); and free-riders' punishment of other free-riders, which is predicted by impatience (present orientation). Therefore, the picture is more complex as punishment by free-riders probably comes not from a reaction against a moral transgression, but instead from a competitive, spiteful drive. Thus, punishment grounded on morals may be related to lasting or delayed psychological incentives, whereas punishment triggered by competitive desires may be linked to short-run aspirations. These results indicate that the individual's time horizon is relevant for the type of social behaviour she opts for. Integrating such differences in inter-temporal preferences and the social behaviour of agents might help to achieve a better understanding of how human cooperation and punishment behaviour has evolved.

  10. Miniature JPL Universal Instrument Bus

    Data.gov (United States)

    National Aeronautics and Space Administration — Develop a Universal Digital Processor Bus architecture using state of the art commercial packaging technologies. This work will transition commercial advanced- yet...

  11. The effect of rider weight and additional weight in Icelandic horses in tölt: part II. Stride parameters responses.

    Science.gov (United States)

    Gunnarsson, V; Stefánsdóttir, G J; Jansson, A; Roepstorff, L

    2017-09-01

    This study investigated the effects of rider weight in the BW ratio (BWR) range common for Icelandic horses (20% to 35%), on stride parameters in tölt in Icelandic horses. The kinematics of eight experienced Icelandic school horses were measured during an incremental exercise test using a high-speed camera (300 frames/s). Each horse performed five phases (642 m each) in tölt at a BWR between rider (including saddle) and horse starting at 20% (BWR20) and increasing to 25% (BWR25), 30% (BWR30), 35% (BWR35) and finally 20% (BWR20b) was repeated. One professional rider rode all horses and weight (lead) was added to saddle and rider as needed. For each phase, eight strides at speed of 5.5 m/s were analyzed for stride duration, stride frequency, stride length, duty factor (DF), lateral advanced placement, lateral advanced liftoff, unipedal support (UPS), bipedal support (BPS) and height of front leg action. Stride length became shorter (Y=2.73-0.004x; P0.05). In conclusion, increased BWR decreased stride length and increased DF proportionally to the same extent in all limbs, whereas BPS increased at the expense of decreased UPS. These changes can be expected to decrease tölt quality when subjectively evaluated according to the breeding goals for the Icelandic horse. However, beat, symmetry and height of front leg lifting were not affected by BWR.

  12. Learning NServiceBus Sagas

    CERN Document Server

    Helton, Rich

    2015-01-01

    If you are an Enterprise C# developer who wishes to extend your knowledge of NServiceBus and Enterprise Service Bus in C#, this is the book for you. This book is designed to enhance the education of ESBs and their messaging, whether you are a beginner or a seasoned expert in Enterprise C#, Apex, and Visualforce pages.

  13. Natural gas powered bus

    International Nuclear Information System (INIS)

    Ambuehl, D.; Fernandez, J.

    2003-01-01

    This report for the Swiss Federal Office of Energy presents the results of a project carried out by the Swiss Federal Institute of Technology in Zurich to evaluate the performance of a natural-gas-powered bus in comparison with two diesel buses. The report provides details on the vehicles, their routes and the results of interviews made with both passengers and drivers. Details of measurements made on fuel consumption and pollutant emissions are presented in tabular and graphical form, as are those made on noise emissions inside and outside the vehicles. The conclusions of the project are presented including economic aspects of using gas as a motor fuel. Also, the views of passengers, who were more concerned with comfort aspects, and drivers, who were more interested in technical aspects, are quoted

  14. Hybrid Electric Transit Bus

    Science.gov (United States)

    Viterna, Larry A.

    1997-01-01

    A government, industry, and university cooperative is developing an advanced hybrid electric city transit bus. Goals of this effort include doubling the fuel economy compared to current buses and reducing emissions to one-tenth of current EPA standards. Unique aspects of the vehicle's power system include the use of ultra-capacitors as an energy storage system, and a planned natural gas fueled turbogenerator developed from a small jet engine. Power from both the generator and energy storage system is provided to a variable speed electric motor attached to the rear axle. At over 15000 kg gross weight, this is the largest vehicle of its kind ever built using ultra-capacitor energy storage. This paper describes the overall power system architecture, the evolution of the control strategy, and its performance over industry standard drive cycles.

  15. 19 CFR 113.26 - Effective dates of bonds and riders.

    Science.gov (United States)

    2010-04-01

    ... effective on the effective date identified on the Customs Bond, Customs Form 301. (d) Riders for name change of principal, address change, and addition of trade names and unincorporated divisions of a corporate principal. Riders for a name change of principal, address change, and addition of trade names and...

  16. Cool Science: Year 2 of Using Children's Artwork about Climate Change to Engage Riders on Mass Transit

    Science.gov (United States)

    Lustick, D. S.; Lohmeier, J.; Chen, R. F.

    2014-12-01

    A team of educators and scientists from the University of Massachusetts Lowell and the University of Massachusetts Boston will report on the second year of an informal science learning research project using mass transit spaces in Lowell, MA. Cool Science (CS) conducts a statewide art competition for K-12 students in the fall challenging them to express climate science understanding through the visual arts. An inter-disciplinary panel of judges evaluates entries and identifies the top 24 works of art. The best six student works of art are then put on public display throughout the spring on the Lowell Regional Transit Authority (LRTA). Displaying student artwork in Out of Home Multi-Media (OHMM) such as bus placards and posters is intended to engage riders with opportunities to learn informally. CS aims to promote and evaluate learning about climate change science among the general public and k-12 students/teachers. The goals of CS are: 1) Engage teachers, students, and parents in a climate change science communication competition. 2) Display the winning 6 artworks from K-12 students throughout the LRTA. 3) Assess the impact of Cool Science on the teaching and learning of climate science in K-12 formal education. 4) Assess the impact of Cool Science artwork on attitudes, awareness, and understanding of climate change among adult bus riders. A naturalistic inquiry employing a mixed methodology approach best describes our research design. The evaluation focuses on providing feedback regarding the potential learning outcomes for the K-12 students who create the media for the project and the general riding public who engage with the student artwork. To identify possible outcomes, data was collected in the several forms: survey, interviews, and online analytics. We see an urgent need to improve both the public's engagement with climate change science and to the profile of climate change science in formal education settings. The Cool Science (CS) project is an opportunity

  17. 76 FR 37184 - Discretionary Bus and Bus Facilities Program

    Science.gov (United States)

    2011-06-24

    ... transporting bicycles on public transportation vehicles. The FY 2011 Appropriations Act allows a 90 percent Federal share for the total cost of a biodiesel bus. The Act also allows a 90 percent Federal share for...

  18. Air-pollution and economics: diesel bus versus electric bus

    OpenAIRE

    Adheesh, SR; Vasisht, Shravanth M; Ramasesha, Sheela K

    2016-01-01

    The Bangalore Metropolitan Transport Corporation (BMTC) took an initiative to check the overall benefits of introducing electric buses as a suitable replacement for the diesel buses to tackle the burgeoning pollution in the city of Bengaluru, India. For a trial run of three months, an electric bus was procured from a Chinese company `Build Your Dreams' (BYD). Data were collected by BMTC on the operation and maintenance of the bus. This new initiative, if rightly guided, could have a direct im...

  19. Enterprise Deployment Through PulseRider To Treat Anterior Communicating Artery Aneurysm Recurrence.

    Science.gov (United States)

    Valente, Iacopo; Limbucci, Nicola; Nappini, Sergio; Rosi, Andrea; Laiso, Antonio; Mangiafico, Salvatore

    2018-02-01

    PulseRider (Pulsar Vascular, Los Gatos, California, USA) is a new endovascular device designed to treat wide-neck bifurcation intracranial aneurysms. Deployment of a stent through a PulseRider to treat an aneurysm's recurrence has never been described before. We report the case of a 55-year-old man who underwent coiling of an 8-mm anterior communicating artery aneurysm with assistance of a PulseRider neck reconstruction device. The 6-month digital subtraction angiography control showed aneurysm recurrence, so we deployed an Enterprise 2 closed-cell stent (Codman, Miami Lakes, Florida, USA) in the A1-A2 segment passing across the previously implanted PulseRider. Enterprise correctly expanded and allowed for adequate coiling of the aneurysm. An Enterprise stent can be safely opened through a PulseRider in order to treat aneurysm recurrence. Copyright © 2017 Elsevier Inc. All rights reserved.

  20. Co-variations between perceived personality traits and quality of the interaction between female riders and horses

    NARCIS (Netherlands)

    Wolframm, I.A.; Meulenbroek, R.G.J.

    2012-01-01

    The current study seeks to investigate the relationship between perceived equine and rider personality traits on the one hand and quality of horse–rider relationships on the other. An Internet questionnaire examined the self-perceived personality traits of 2525 horse–female rider dyads that

  1. The social context of motorcycle riding and the key determinants influencing rider behavior: a qualitative investigation.

    Science.gov (United States)

    Tunnicliff, Deborah; Watson, Barry; White, Katherine M; Lewis, Ioni; Wishart, Darren

    2011-08-01

    Given the increasing popularity of motorcycle riding and heightened risk of injury or death associated with being a rider, this study explored rider behavior as a determinant of rider safety and, in particular, key beliefs and motivations that influence such behavior. To enhance the effectiveness of future education and training interventions, it is important to understand riders' own views about what influences how they ride. Specifically, this study sought to identify key determinants of riders' behaviors in relation to the social context of riding, including social and identity-related influences relating to the group (group norms and group identity) as well as the self (moral/personal norm and self-identity). Qualitative research was undertaken via group discussions with motorcycle riders (n = 41). The findings revealed that those in the group with which one rides represent an important source of social influence. Also, the motorcyclist (group) identity was associated with a range of beliefs, expectations, and behaviors considered to be normative. Exploration of the construct of personal norm revealed that riders were most cognizant of the "wrong things to do" when riding; among those issues raised was the importance of protective clothing (albeit for the protection of others and, in particular, pillion passengers). Finally, self-identity as a motorcyclist appeared to be important to a rider's self-concept and was likely to influence on-road behavior. Overall, the insight provided by the current study may facilitate the development of interventions including rider training as well as public education and mass media messages. The findings suggest that these interventions should incorporate factors associated with the social nature of riding in order to best align it with some of the key beliefs and motivations underpinning riders' on-road behaviors.

  2. Scaling Laws in Chennai Bus Network

    OpenAIRE

    Chatterjee, Atanu; Ramadurai, Gitakrishnan

    2015-01-01

    In this paper, we study the structural properties of the complex bus network of Chennai. We formulate this extensive network structure by identifying each bus stop as a node, and a bus which stops at any two adjacent bus stops as an edge connecting the nodes. Rigorous statistical analysis of this data shows that the Chennai bus network displays small-world properties and a scale-free degree distribution with the power-law exponent, $\\gamma > 3$.

  3. Basic kinematics of the saddle and rider in high-level dressage horses trotting on a treadmill.

    Science.gov (United States)

    Byström, A; Rhodin, M; von Peinen, K; Weishaupt, M A; Roepstorff, L

    2009-03-01

    A comprehensive kinematic description of rider and saddle movements is not yet present in the scientific literature. To describe saddle and rider movements in a group of high-level dressage horses and riders. Seven high-level dressage horses and riders were subjected to kinematic measurements while performing collected trot on a treadmill. For analysis a rigid body model for the saddle and core rider segments, projection angles of the rider's extremities and the neck and trunk of the horse, and distances between markers selected to indicate rider position were used. For a majority of the variables measured it was possible to describe a common pattern for the group. Rotations around the transverse axis (pitch) were generally biphasic for each diagonal. During the first half of stance the saddle rotated anti-clockwise and the rider's pelvis clockwise viewed from the right and the rider's lumbar back extended. During the later part of stance and the suspension phase reverse pitch rotations were observed. Rotations of the saddle and core rider segments around the longitudinal (roll) and vertical axes (yaw) changed direction only around time of contact of each diagonal. The saddles and riders of high-level dressage horses follow a common movement pattern at collected trot. The movements of the saddle and rider are clearly related to the movements of the horse and saddle movements also seem to be influenced by the rider. Knowledge about rider and saddle movements can further our understanding of, and hence possibilities to prevent, orthopaedic injuries related to the exposure of the horse to a rider and saddle.

  4. The Wise Bus Buyer.

    Science.gov (United States)

    Dervarics, Charles

    1993-01-01

    School transportation experts consider the following essential rules in purchasing school buses: know your geography; know federal and state regulations; write specifications carefully; plan for replacement and growth; check out prospective bidders; keep up with recent trends; and remain flexible. New Jersey enacted a law last year requiring seat…

  5. Patterns of horse-rider coordination during endurance race: a dynamical system approach.

    Directory of Open Access Journals (Sweden)

    Sylvain Viry

    Full Text Available In riding, most biomechanical studies have focused on the description of the horse locomotion in unridden condition. In this study, we draw the prospect of how the basic principles established in inter-personal coordination by the theory of Coordination Dynamics may provide a conceptual and methodological framework for understanding the horse-rider coupling. The recent development of mobile technologies allows combined horse and rider recordings during long lasting natural events such as endurance races. Six international horse-rider dyads were thus recorded during a 120 km race by using two tri-axial accelerometers placed on the horses and riders, respectively. The analysis concentrated on their combined vertical displacements. The obtained shapes and angles of Lissajous plots together with values of relative phase between horse and rider displacements at lower reversal point allowed us to characterize four coordination patterns, reflecting the use of two riding techniques per horse's gait (trot and canter. The present study shows that the concepts, methods and tools of self-organizing dynamic system approach offer new directions for understanding horse-rider coordination. The identification of the horse-rider coupling patterns constitutes a firm basis to further study the coalition of multiple constraints that determine their emergence and their dynamics in endurance race.

  6. Bus systems in motor vehicles; Bussysteme im Kfz

    Energy Technology Data Exchange (ETDEWEB)

    Schule, Roland

    2008-07-01

    There is hardly any modern vehicle without a bus system. This interactive learning software explains why electric and electronic systems in motor vehicles should be linked and uses various bus types to illustrate the various alternatives, bus structures, and data types. The physical side of bus systems is gone into, the data structure is explained, and the various bus typologies are outlined. From the fundamentals of bus systems, the software proceeds to present the most important bus systems and their main properties. Subjects: Diagnosis bus, LIN bus, CAN bus, MOST bus, Bluetooth. The bus systems EIA-485, LVDS, D{sup 2}B, byteflight, and Flexray are briefly characterised. (orig.)

  7. The effect of rider weight and additional weight in Icelandic horses in tölt: part I. Physiological responses.

    Science.gov (United States)

    Stefánsdóttir, G J; Gunnarsson, V; Roepstorff, L; Ragnarsson, S; Jansson, A

    2017-09-01

    This study examined the effect of increasing BW ratio (BWR) between rider and horse, in the BWR range common for Icelandic horses (20% to 35%), on heart rate (HR), plasma lactate concentration (Lac), BWR at Lac 4 mmol/l (W4), breathing frequency (BF), rectal temperature (RT) and hematocrit (Hct) in Icelandic horses. In total, eight experienced school-horses were used in an incremental exercise test performed outdoors on an oval riding track and one rider rode all horses. The exercise test consisted of five phases (each 642 m) in tölt, a four-beat symmetrical gait, at a speed of 5.4±0.1 m/s (mean±SD), where BWR between rider (including saddle) and horse started at 20% (BWR20), was increased to 25% (BWR25), 30% (BWR30), and 35% (BWR35) and finally decreased to 20% (BWR20b). Between phases, the horses were stopped (~5.5 min) to add lead weights to specially adjusted saddle bags and a vest on the rider. Heart rate was measured during warm-up, the exercise test and after 5, 15 and 30 min of recovery and blood samples were taken and BF recorded at rest, and at end of each of these aforementioned occasions. Rectal temperature was measured at rest, at end of the exercise test and after a 30-min recovery period. Body size and body condition score (BCS) were registered and a clinical examination performed on the day before the test and for 2 days after. Heart rate and BF increased linearly (P0.05), but negative correlations (Phorses had no clinical remarks on palpation and at walk 1 and 2 days after the test. In conclusion, increasing BWR from 20% to 35% resulted in increased HR, Lac, RT and BF responses in the test group of experienced adult Icelandic riding horses. The horses mainly worked aerobically until BWR reached 22.7%, but considerable individual differences (17.0% to 27.5%) existed that were not linked to horse size, but to back BCS.

  8. Fuel cell bus operation, system investigation H2 bus

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    The WP covers two tasks: - Prepartion of Technical Catalogue: In cooperation with ICIL, AR have compiled a technical catalogue, providing the impartial descriptions, both of existing technology and regulations, and the likely future developments of these, as to remedy the first problem faced by a potential hydrogen bus fleet operator viz the absence of an impartial description of the available vehicle and fuels systems together with the absence of a description of regulatory and safety factors which need consideration. - Fuel Cell Bus Operation - System Investigation H 2 Bus: The application of fuel cell electric generation systems to hybrid electrical buses or electrical busses without any storage system on board is considered. The task will cover safety and environmental aspects, a cost estimate and a market evaluation. (orig.)

  9. Study of vibration and its effect on health of the motorcycle rider

    Directory of Open Access Journals (Sweden)

    Shivakumara BS

    2010-07-01

    Full Text Available The motorcycle riders are subjected to extreme vibrations due to the vibrations of its engine, improper structural design of the motorcycle and the bad road conditions. The literature review reveals that the vibrations are most hazardous to the health if it exceeds the limit. The experiments were conducted to measure the magnitude of the vibrations acting on the rider during motorcycle riding under various road conditions. Experimental values of accelerations and frequencies which are beyond permissible limits according to the literature confirm that vibration certainly affects health of the motorcycle rider

  10. Attitudes and intentions of off-highway vehicle riders toward trail use: implications for forest managers

    Science.gov (United States)

    Kuehn, D.M.; D'Luhosch, P. D.; Luzadis, V.A.; Malmsheimer, R.W.; Schuster, R.M.

    2011-01-01

    Management of off-highway vehicles (OHV) in public forest areas requires up-to-date information about the attitudes and intentions of OHV riders toward trail use. A survey of 811 members of the New England Trail Riders Association was conducted in fall 2007; 380 questionnaires were completed and returned. Descriptive statistics and regressions were used to identify relationships between OHV rider attitudes, management preferences, and intentions toward two trail use-related behaviors (i.e., illegal use of trails by OHVs and the creation and/or use of unauthorized trails by OHV riders). Results reveal that the average responding association member has a negative attitude toward the two depreciative behaviors, intends to ride OHVs legally, and slightly prefers indirect over direct forms of management. Significant relationships between intentions and both attitudes and management preferences are identified. Policy and management implications and strategies are discussed. ?? 2011 by the Society of American Foresters.

  11. Underbelly injury based identification of the driver in a three-rider motorcycle accident.

    Science.gov (United States)

    Liu, Shengxiong; Yin, Zhiyong; Su, Sen; Li, Kui

    2016-01-01

    This paper presents a three-rider motorcycle accident which took place in a suburb of Chongqing China. In the accident, the motorcycle impacted the terminal of a bridge footpath and led to two riders died and one rider injured. After the accident, one rider received injuries around the groin area including the underbelly area and the perineum area. Another rider suffered from injuries only on the perineum areas. In medico-legal judgments, injuries around the groin area also called groin injuries in victims of motorcycle accidents are usually regarded as "fuel tank injuries" which are commonly found in drivers. But, the injuries around the groin area are sometimes confused with the perineum injuries. Therefore, the perineum injuries are often wrongly reckoned as the "fuel tank injuries" and used to identify the drivers too. Actually, passengers can sometimes suffer from perineum injuries in many head-on impacting motorcycle accidents. It is of vital matters to understand the differences between groin injuries and perineum injuries so that the real driver who should be responsible for the accident can be recognized. In this paper, the three-rider motorcycle accident was presented and the injury information of the three riders was studied in order to distinguish the real driver from the riders. We consider that the groin injury has some differences with the perineum injury and the latter should not always be related to the driver especially in high-speed head-on impacting motorcycle accidents. In addition, the injury on underbelly areas is important to identify the driver. Crown Copyright © 2015. Published by Elsevier Ireland Ltd. All rights reserved.

  12. Optimizing Tailored Bus Bridging Paths

    NARCIS (Netherlands)

    Gu, Wei; Yu, Jie; Ji, Yuxiong; van der Gun, J.P.T.; Pel, A.J.; Zhang, H. Michael; van Arem, B.

    2017-01-01

    Metro disruptions due to unexpected events reduce transit system reliability, resulting in significant productivity loss and long passenger delays. Bus bridging strategy is often used to connect stations affected by metro disruptions such that passengers could continue their journey. The literature

  13. Bus transport in Greater Manchester

    DEFF Research Database (Denmark)

    Sørensen, Claus Hedegaard; Gudmundsson, Henrik

    component regards the organisation of public bus transport at the local level. This involves the deregulation and privatisation reforms introduced by the Conservative Government from 1986 onwards, as well as the ‘partnerships’ and other new instruments introduced by the Labour Government in the Transport...

  14. Pybus - A Python Software Bus

    International Nuclear Information System (INIS)

    Lavrijsen, Wim T.L.P.

    2004-01-01

    A software bus, just like its hardware equivalent, allows for the discovery, installation, configuration, loading, unloading, and run-time replacement of software components, as well as channeling of inter-component communication. Python, a popular open-source programming language, encourages a modular design on software written in it, but it offers little or no component functionality. However, the language and its interpreter provide sufficient hooks to implement a thin, integral layer of component support. This functionality can be presented to the developer in the form of a module, making it very easy to use. This paper describes a Pythonmodule, PyBus, with which the concept of a ''software bus'' can be realized in Python. It demonstrates, within the context of the ATLAS software framework Athena, how PyBus can be used for the installation and (run-time) configuration of software, not necessarily Python modules, from a Python application in a way that is transparent to the end-user

  15. Connecting and Networking for Schools

    Science.gov (United States)

    Resources for connecting and networking for schools through e-newsletters, finding school IAQ Champions and other EPA school programs such as Asthma, Energy Star, Clean School Bus USA, School Flag, etc.

  16. Analysis of robustness of urban bus network

    Science.gov (United States)

    Tao, Ren; Yi-Fan, Wang; Miao-Miao, Liu; Yan-Jie, Xu

    2016-02-01

    In this paper, the invulnerability and cascade failures are discussed for the urban bus network. Firstly, three static models(bus stop network, bus transfer network, and bus line network) are used to analyse the structure and invulnerability of urban bus network in order to understand the features of bus network comprehensively. Secondly, a new way is proposed to study the invulnerability of urban bus network by modelling two layered networks, i.e., the bus stop-line network and the bus line-transfer network and then the interactions between different models are analysed. Finally, by modelling a new layered network which can reflect the dynamic passenger flows, the cascade failures are discussed. Then a new load redistribution method is proposed to study the robustness of dynamic traffic. In this paper, the bus network of Shenyang City which is one of the biggest cities in China, is taken as a simulation example. In addition, some suggestions are given to improve the urban bus network and provide emergency strategies when traffic congestion occurs according to the numerical simulation results. Project supported by the National Natural Science Foundation of China (Grant Nos. 61473073, 61374178, 61104074, and 61203329), the Fundamental Research Funds for the Central Universities (Grant Nos. N130417006, L1517004), and the Program for Liaoning Excellent Talents in University (Grant No. LJQ2014028).

  17. Electrical system architecture having high voltage bus

    Science.gov (United States)

    Hoff, Brian Douglas [East Peoria, IL; Akasam, Sivaprasad [Peoria, IL

    2011-03-22

    An electrical system architecture is disclosed. The architecture has a power source configured to generate a first power, and a first bus configured to receive the first power from the power source. The architecture also has a converter configured to receive the first power from the first bus and convert the first power to a second power, wherein a voltage of the second power is greater than a voltage of the first power, and a second bus configured to receive the second power from the converter. The architecture further has a power storage device configured to receive the second power from the second bus and deliver the second power to the second bus, a propulsion motor configured to receive the second power from the second bus, and an accessory motor configured to receive the second power from the second bus.

  18. Characterisation of an urban bus network for environmental purposes.

    Science.gov (United States)

    André, Michel; Villanova, André

    2004-12-01

    Since pollutant emissions are closely related to the operating conditions of vehicles, their evaluation usually involves studying these operating conditions (through bus instrumentation and monitoring under actual operation), the design of representative driving or engine test cycles and the measurement of pollutant emissions. A preliminary characterisation of the routes on a bus network should make it possible to identify typical routes, the driving conditions and pollutant emissions of which are then studied. Two approaches are envisaged and applied to the Paris area, for which a wealth of information is available, which should be transferable to other bus networks. Both approaches are based on factorial analysis and automatic clustering, to allow optimum description and the identification of a pertinent typology of the bus routes in several classes. The first attempt at characterisation is based on statistics relating to bus operations: route characteristics (length, dedicated bus lanes, number of stops, location of stops: schools, tourist sites, hospitals, railways or underground stations), travel time, commercial speed, annual statistics (number of passengers, number of vehicles per hour, total kilometres), the irregularity of travel (variation of travel times, injuries, congestion.), as well as information on the problems encountered (congestion, distribution of the passenger load, junctions, bends). A second approach is based on the analysis of the "urban context" in which buses are driven. Population, employment, housing, road network, traffic and places that generate or disturb traffic (schools, railway stations, shopping areas, etc.) are calculated for the Ile de France region, by cells of 100 x 100 m, and collected in a geographical information system (GIS). Statistical analyses enable a typology of these urban cells to be established, the main parameters being density, type of housing, road types and traffic levels. The bus routes are then analysed

  19. Avionic Data Bus Integration Technology

    Science.gov (United States)

    1991-12-01

    address the hardware-software interaction between a digital data bus and an avionic system. Very Large Scale Integration (VLSI) ICs and multiversion ...the SCP. In 1984, the Sperry Corporation developed a fault tolerant system which employed multiversion programming, voting, and monitoring for error... MULTIVERSION PROGRAMMING. N-version programming. 226 N-VERSION PROGRAMMING. The independent coding of a number, N, of redundant computer programs that

  20. New TPG bus route 28

    CERN Multimedia

    2003-01-01

    Geneva's Public Transport services (TPG) have recently inaugurated a new bus line 28, connecting the La Tour Hospital in Meyrin to the international organisations in Geneva, via the airport. All signs associated with this route will be yellow in colour. Timetables and route details can be found at http://www.tpg.ch. Relations with the Host States Service http://www.cern.ch/relations/ Tel. 72848

  1. Pediatric anthropometrics are inconsistent with current guidelines for assessing rider fit on all-terrain vehicles.

    Science.gov (United States)

    Bernard, Andrew C; Mullineaux, David R; Auxier, James T; Forman, Jennifer L; Shapiro, Robert; Pienkowski, David

    2010-07-01

    This study sought to establish objective anthropometric measures of fit or misfit for young riders on adult and youth-sized all-terrain vehicles and use these metrics to test the unproved historical reasoning that age alone is a sufficient measure of rider-ATV fit. Male children (6-11 years, n=8; and 12-15 years, n=11) were selected by convenience sampling. Rider-ATV fit was quantified by five measures adapted from published recommendations: (1) standing-seat clearance, (2) hand size, (3) foot vs. foot-brake position, (4) elbow angle, and (5) handlebar-to-knee distance. Youths aged 12-15 years fit the adult-sized ATV better than the ATV Safety Institute recommended age-appropriate youth model (63% of subjects fit all 5 measures on adult-sized ATV vs. 20% on youth-sized ATV). Youths aged 6-11 years fit poorly on ATVs of both sizes (0% fit all 5 parameters on the adult-sized ATV vs 12% on the youth-sized ATV). The ATV Safety Institute recommends rider-ATV fit according to age and engine displacement, but no objective data linking age or anthropometrics with ATV engine or frame size has been previously published. Age alone is a poor predictor of rider-ATV fit; the five metrics used offer an improvement compared to current recommendations. Copyright 2010 Elsevier Ltd. All rights reserved.

  2. SOLVING OF SCHOOL BUS ROUTING PROBLEM BY ANT COLONY OPTIMIZATION RESOLUCIÓN DEL PROBLEMA DE RUTEO DE BUSES ESCOLARES CON OPTIMIZACIÓN POR COLONIA DE HORMIGAS RESOLUÇÃO DO PROBLEMA DE RUTEO DE ÔNIBUS ESCOLARES COM OTIMIZAÇÃO POR COLÔNIA DE FORMIGAS

    Directory of Open Access Journals (Sweden)

    Juan S Arias-Rojas

    2012-06-01

    Full Text Available The school bus routing problem (SBRP seeks to plan an efficient schedule of a fleet of school buses that must pick up students from various bus stops and deliver them by satisfying various constraints: maximum capacity of the bus, maximum riding time of students, time window to arrive to school. In this paper, we consider a case study of SBRP for a school in Bogotá, Colombia. The problem is solved using ant colony optimization (ACO. Computational experiments are performed using real data. Results lead to increased bus utilization and reduction in transportation times with on-time delivery to the school. The proposed decision-aid tool has shown its usefulness for actual decision-making at the school: it outperforms current routing by reducing the total distance traveled by 8.3 % and 21.4 % respectively in the morning and in the afternoon.El problema de ruteo de buses escolares (SBRP busca encontrar el programa más eficiente para una flota de buses escolares que deben recoger y despachar estudiantes en varias paradas de bus satisfaciendo varias restricciones: capacidad máxima del bus, máximo tiempo de recorrido de los estudiantes, ventanas de tiempo para la llegada al colegio. En este artículo se considera un caso de estudio de un problema SBRP para un colegio en Bogotá, Colombia. El problema se resuelve usando la metaheurística de colonia de hormigas (ACO. Los experimentos computacionales se realizan empleando datos reales. Los resultados muestran el incremento en el nivel de utilización de los buses y una reducción en los tiempos de transporte con despacho a tiempo en el colegio. La herramienta ha mostrado su utilidad para la planeación regular de buses en el colegio: se redujo la distancia total recorrida en 8,3 % en la mañana y en 21,4 % en la tarde.O problema de roteamento de ônibus escolares (SBRP busca encontrar o programa mais eficiente para uma frota de ônibus escolares que devem recolher e despachar estudantes em v

  3. National fuel cell bus program : proterra fuel cell hybrid bus report, Columbia demonstration.

    Science.gov (United States)

    2011-10-01

    This report summarizes the experience and early results from a fuel cell bus demonstration funded by the Federal Transit Administration (FTA) under the National Fuel Cell Bus Program. A team led by the Center for Transportation and the Environment an...

  4. Sustainable institutionalized punishment requires elimination of second-order free-riders

    Science.gov (United States)

    Perc, Matjaž

    2012-03-01

    Although empirical and theoretical studies affirm that punishment can elevate collaborative efforts, its emergence and stability remain elusive. By peer-punishment the sanctioning is something an individual elects to do depending on the strategies in its neighborhood. The consequences of unsustainable efforts are therefore local. By pool-punishment, on the other hand, where resources for sanctioning are committed in advance and at large, the notion of sustainability has greater significance. In a population with free-riders, punishers must be strong in numbers to keep the ``punishment pool'' from emptying. Failure to do so renders the concept of institutionalized sanctioning futile. We show that pool-punishment in structured populations is sustainable, but only if second-order free-riders are sanctioned as well, and to a such degree that they cannot prevail. A discontinuous phase transition leads to an outbreak of sustainability when punishers subvert second-order free-riders in the competition against defectors.

  5. 77 FR 51935 - Adjustment of the Amount for the Optional Bond Rider for Proof of NVOCC Financial Responsibility...

    Science.gov (United States)

    2012-08-28

    ....'' Mohawk did not identify disadvantages to the increase, other than the minor administrative burden of... and disadvantages of an adjustment to the current optional rider to the required NVOCC bond? 3. Please... in the cost of the China Bond Rider coverage. These disadvantages would be multiplied if the...

  6. Are all-terrain vehicle riders willing to pay trail user fees to ride on public lands in the USA?

    Science.gov (United States)

    Stephanie A. Snyder; Robert A. Smail

    2009-01-01

    Some public lands in the USA offer opportunities for all-terrain vehicle (ATV) riding, but few charge trail use fees. In a case study in the US state of Wisconsin, the contingent valuation method was used to examine riders' willingness to pay (WTP) to ride on public lands. Information on riders' habits, preferences and responses to a dichotomous choice WTP...

  7. Bus Route Design with a Bayesian Network Analysis of Bus Service Revenues

    OpenAIRE

    Liu, Yi; Jia, Yuanhua; Feng, Xuesong; Wu, Jiang

    2018-01-01

    A Bayesian network is used to estimate revenues of bus services in consideration of the effect of bus travel demands, passenger transport distances, and so on. In this research, the area X in Beijing has been selected as the study area because of its relatively high bus travel demand and, on the contrary, unsatisfactory bus services. It is suggested that the proposed Bayesian network approach is able to rationally predict the probabilities of different revenues of various route services, from...

  8. Road safety issues for bus transport management.

    Science.gov (United States)

    Cafiso, Salvatore; Di Graziano, Alessandro; Pappalardo, Giuseppina

    2013-11-01

    Because of the low percentage of crashes involving buses and the assumption that public transport improves road safety by reducing vehicular traffic, public interest in bus safety is not as great as that in the safety of other types of vehicles. It is possible that less attention is paid to the significance of crashes involving buses because the safety level of bus systems is considered to be adequate. The purpose of this study was to evaluate the knowledge and perceptions of bus managers with respect to safety issues and the potential effectiveness of various technologies in achieving higher safety standards. Bus managers were asked to give their opinions on safety issues related to drivers (training, skills, performance evaluation and behaviour), vehicles (maintenance and advanced devices) and roads (road and traffic safety issues) in response to a research survey. Kendall's algorithm was used to evaluate the level of concordance. The results showed that the majority of the proposed items were considered to have great potential for improving bus safety. The data indicated that in the experience of the participants, passenger unloading and pedestrians crossing near bus stops are the most dangerous actions with respect to vulnerable users. The final results of the investigation showed that start inhibition, automatic door opening, and the materials and internal architecture of buses were considered the items most strongly related to bus passenger safety. Brake assistance and vehicle monitoring systems were also considered to be very effective. With the exception of driver assistance systems for passenger and pedestrian safety, the perceptions of the importance of other driver assistance systems for vehicle monitoring and bus safety were not unanimous among the bus company managers who participated in this survey. The study results showed that the introduction of new technologies is perceived as an important factor in improving bus safety, but a better understanding

  9. American fuel cell bus project : first analysis report.

    Science.gov (United States)

    2013-06-01

    This report summarizes the experience and early results from the American Fuel Cell Bus Project, a fuel cell electric bus demonstration : funded by the Federal Transit Administration (FTA) under the National Fuel Cell Bus Program. A team led by CALST...

  10. Fuel Cell Electric Bus Evaluations | Hydrogen and Fuel Cells | NREL

    Science.gov (United States)

    Bus Evaluations Fuel Cell Electric Bus Evaluations NREL's technology validation team evaluates fuel cell electric buses (FCEBs) to provide comprehensive, unbiased evaluation results of fuel cell bus early transportation applications for fuel cell technology. Buses operate in congested areas where

  11. Design & Development of FPGA Based VME Bus Controller

    OpenAIRE

    Himali Patel; Poornima Talwai

    2015-01-01

    The VME bus interface Controller (VIC068A) is used to interface Local CPU bus and VME bus. VME Bus Controller is used in wide application areas where high reliability, good accuracy and high speed are desired to withstand industrial environment like nuclear power plant and process industries. VME Bus controller can configure as Master, Slave, Interrupt Handler, arbiter as well as power monitor. Commercial VME Bus interface controller chips are available from a few vend...

  12. Mastering NServiceBus and persistence

    CERN Document Server

    Helton, Rich

    2014-01-01

    This book is intended for developers, designers, and architects alike who wish to build C# NServiceBus enterprise architectures and learn how ESB persists data and messages to help them attain their goals. No prior knowledge of persistence in NServiceBus is required.

  13. Digital processing data communication systems (bus systems)

    International Nuclear Information System (INIS)

    Fleck, K.

    1980-01-01

    After an introduction to the technology of digital processing data communication systems there are the following chapters: digital communication of processing data in automation technology, the technology of biserial communication, the implementaiton of a bus system, the data transmission of the TDC-2000 system of Honeywell's and the process bus CS 275 in the automation system TELEPERM M of Siemens AG. (WB) [de

  14. Impact of noise on hearing amongst commercial motor bike riders in ...

    African Journals Online (AJOL)

    Impact of noise on hearing amongst commercial motor bike riders in Benin- City, Nigeria. ... While there was no NIHI in control group, a significant hearing impairment for both air conduction (AC) and Bone conduction (BC) was observed in the study group. Unlike previous observations AC and BC impairment were ...

  15. Analysis of the stability of PTW riders in autonomous braking scenarios.

    Science.gov (United States)

    Symeonidis, Ioannis; Kavadarli, Gueven; Erich, Schuller; Graw, Matthias; Peldschus, Steffen

    2012-11-01

    While fatalities of car occupants in the EU decreased remarkably over the last decade, Powered Two Wheelers (PTWs) fatalities still increase following the increase of PTW ownership. Autonomous braking systems have been implemented in several types of vehicles and are presently addressed by research in the field of PTWs. A major concern in this context is the rider stability. Experiments with volunteers were performed in order to find out whether autonomous braking for PTWs will produce a greater instability of the rider in comparison to manual braking. The PTW's braking conditions were simulated in a laboratory with a motorcycle mock-up mounted on a sled, which was accelerated with an average of 0.35 g. The motion of the rider was captured in autonomous braking scenarios with and without pre-warning as well as in manual braking scenarios. No significant differences between the scenarios were found with respect to maximum forward displacement of the volunteer's torso and head (pautonomous braking at low deceleration will not cause significant instabilities of the rider in comparison to manual braking in idealized laboratory conditions. Based on this, further research into the development and implementation of autonomous braking systems for PTWs, e.g. by extensive riding tests, seems valuable. Copyright © 2011 Elsevier Ltd. All rights reserved.

  16. The Streetboard Rider: An Appealing Problem in Non-Holonomic Mechanics

    Science.gov (United States)

    Janova, J.; Musilova, J.

    2010-01-01

    This paper enlarges the reservoir of solved tutor problems in non-holonomic mechanics at the undergraduate level of physics education. Unlike other, rather artificial, solved problems typically used, the streetboard-rider locomotion problem presented here represents an appealing contemporary real-world problem with interesting applications in a…

  17. News Teaching Support: New schools network launched Competition: Observatory throws open doors to a select few Festival: Granada to host 10th Ciencia en Acción Centenary: Science Museum celebrates 100 years Award: Queen's birthday honour for science communicator Teacher Training: Training goes where it's needed Conference: Physics gets creative in Christchurch Conference: Conference is packed with ideas Poster Campaign: Bus passengers learn about universe Forthcoming events

    Science.gov (United States)

    2009-09-01

    Teaching Support: New schools network launched Competition: Observatory throws open doors to a select few Festival: Granada to host 10th Ciencia en Acción Centenary: Science Museum celebrates 100 years Award: Queen's birthday honour for science communicator Teacher Training: Training goes where it's needed Conference: Physics gets creative in Christchurch Conference: Conference is packed with ideas Poster Campaign: Bus passengers learn about universe Forthcoming events

  18. Determinants of helmet use behaviour among employed motorcycle riders in Yazd, Iran based on theory of planned behaviour.

    Science.gov (United States)

    Ali, Mehri; Saeed, Mazloomy Mahmoodabad Seyed; Ali, Morowatisharifabad Mohammad; Haidar, Nadrian

    2011-09-01

    This paper reports on predictors of helmet use behaviour, using variables based on the theory of planned behaviour model among the employed motorcycle riders in Yazd-Iran, in an attempt to identify influential factors that may be addressed through intervention efforts. In 2007, a cluster random sample of 130 employed motorcycle riders in the city of Yazd in central Iran, participated in the study. Appropriate instruments were designed to measure the variables of interest (attitude, subjective norms, perceived behaviour control, intention along with helmet use behaviour). Reliability and validity of the instruments were examined and approved. The statistical analysis of the data included descriptive statistics, bivariate correlations, and multiple regression. Based on the results, 56 out of all the respondents (43.1%) had history of accident by motorcycle. Of these motorcycle riders only 10.7% were wearing their helmet at the time of their accident. Intention and perceived behavioural control showed a significant relationship with helmet use behaviour and perceived behaviour control was the strongest predictor of helmet use intention, followed by subjective norms, and attitude. It was found that that helmet use rate among motorcycle riders was very low. The findings of present study provide a preliminary support for the TPB model as an effective framework for examining helmet use in motorcycle riders. Understanding motorcycle rider's thoughts, feelings and beliefs about helmet use behaviour can assist intervention specialists to develop and implement effective programs in order to promote helmet use among motorcycle riders. Copyright © 2010 Elsevier Ltd. All rights reserved.

  19. Safety system for child pillion riders of underbone motorcycles in Malaysia.

    Science.gov (United States)

    Sivasankar, S; Karmegam, K; Bahri, M T Shamsul; Naeini, H Sadeghi; Kulanthayan, S

    2014-01-01

    Motorcycles are a common mode of transport for most Malaysians. Underbone motorcycles are one of the most common types of motorcycle used in Malaysia due to their affordable price and ease of use, especially in heavy traffic in the major cities. In Malaysia, it is common to see a young or child pillion rider clinging on to an adult at the front of the motorcycle. One of the main issues facing young pillion riders is that their safety is often not taken into account when they are riding on a motorcycle. This article reviews the legally available systems in child safety for underbone motorcycles in Malaysia while putting forth the need for a safety system for child pillion riders. Various databases were searched for underbone motorcycle safety systems, related legislation, motorcycle accident data, and types of injuries and these were reviewed to put forth the need for a new safety system. In motorcycle-related accidents, children usually sustain lower limb injuries, which could temporarily or permanently inhibit the child's movements. Accident statistics in Malaysia, especially those involving motorcycles, reflect a pressing need for a reduction in the number of accidents. In Malaysia, the legislation does not go beyond the mandatory use of safety helmets for young pillion users. There is a pressing need for another safety system or mechanism(s) for young pillion riders of underbone motorcycles. Enforcement of laws to enforce the usage of passive safety systems such as helmets and protective gear is difficult in underdeveloped and developing countries. The intervention of new technology is inevitable. Therefore, this article highlights the need for a new safety backrest system for child pillion riders to ensure their safety.

  20. A Hybrid Column Generation and Clustering Approach to the School Bus Routing Problem with Time WindowsUn Aproximación Híbrida de Generación de Columnas y Agrupación para Resolver el Problema de Ruteo de Buses Escolares con Ventanas deTiempo

    Directory of Open Access Journals (Sweden)

    Eduyn Ramiro Lopez Santana

    2015-03-01

    Full Text Available This paper attempts to solve the School Bus Routing Problem with Time Windows that consists of finding the best set of routes to pick up students distributed geographically with constraints as capacity, time windows and maximum travel time. We formulated the problem as a classic Vehicle Routing Problem with Time Windows and solved it using an approach based on a clustering algorithm and column generation method. A real world case from a school in Bogotá, Colombiais presented including 600 students to pick up in near 400 nodes located in urban and rural areas. The obtained results demonstrate a reduction as the problem’s complexity and  an improvement on the performance measures of the proposed method.

  1. Does an on-road motorcycle coaching program reduce crashes in novice riders? A randomised control trial.

    Science.gov (United States)

    Ivers, Rebecca Q; Sakashita, Chika; Senserrick, Teresa; Elkington, Jane; Lo, Serigne; Boufous, Soufiane; de Rome, Liz

    2016-01-01

    Motorcycle riding is increasing globally and confers a high risk of crash-related injury and death. There is community demand for investment in rider training programs but no high-quality evidence about its effectiveness in preventing crashes. This randomised trial of an on-road rider coaching program aimed to determine its effectiveness in reducing crashes in novice motorcycle riders. Between May 2010 and October 2012, 2399 newly-licensed provisional riders were recruited in Victoria, Australia and completed a telephone interview before randomisation to intervention or control groups. Riders in the intervention group were offered an on-road motorcycle rider coaching program which involved pre-program activities, 4h riding and facilitated discussion in small groups with a riding coach. Outcome measures were collected for all participants via telephone interviews at 3 and 12 months after program delivery (or equivalent for controls), and via linkage to police-recorded crash and offence data. The primary outcome was a composite measure of police-recorded and self-reported crashes; secondary outcomes included traffic offences, near crashes, riding exposure, and riding behaviours and motivations. Follow-up was 89% at 3 months and 88% at 12 months; 60% of the intervention group completed the program. Intention-to-treat analyses conducted in 2014 indicated no effect on crash risk at 3 months (adjusted OR 0.90, 95% CI: 0.65-1.27) or 12 months (adjusted OR 1.00, 95% CI: 0.78-1.29). Riders in the intervention group reported increased riding exposure, speeding behaviours and rider confidence. There was no evidence that this on-road motorcycle rider coaching program reduced the risk of crash, and we found an increase in crash-related risk factors. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

  2. Methodology of mixed load customized bus lines and adjustment based on time windows

    Science.gov (United States)

    Song, Rui

    2018-01-01

    Custom bus routes need to be optimized to meet the needs of a customized bus for personalized trips of different passengers. This paper introduced a customized bus routing problem in which trips for each depot are given, and each bus stop has a fixed time window within which trips should be completed. Treating a trip as a virtual stop was the first consideration in solving the school bus routing problem (SBRP). Then, the mixed load custom bus routing model was established with a time window that satisfies its requirement and the result were solved by Cplex software. Finally, a simple network diagram with three depots, four pickup stops, and five delivery stops was structured to verify the correctness of the model, and based on the actual example, the result is that all the buses ran 124.42 kilometers, the sum of kilometers was 10.35 kilometers less than before. The paths and departure times of the different busses that were provided by the model were evaluated to meet the needs of the given conditions, thus providing valuable information for actual work. PMID:29320505

  3. Prevalence of alcohol and drugs among motorcycle riders killed in road crashes in Norway during 2001-2010.

    Science.gov (United States)

    Christophersen, Asbjørg S; Gjerde, Hallvard

    2015-07-01

    The aim of the study was to examine the prevalence of alcohol and drugs in blood samples from motorcycle riders who died in road crashes in Norway from 2001 to 2010. An additional aim was to compare the prevalence of alcohol and drugs in blood samples from fatally injured motorcycle riders and car drivers who died during the same time period. Blood samples from motorcycle riders who died within 24h after the accident (n=207, 63% of all killed riders), were analysed for alcohol, psychoactive drugs (medicinal and illicit drugs). The cut-off concentrations for alcohol and drugs findings in blood samples (i.e., the drug concentrations above which a finding was regarded as positive) were set according to the legislative limits under the Norwegian Road Traffic Act. Results were assessed in relation to age, sex, time of the day and week, and single versus multiple-vehicle accidents. Alcohol or drugs were found in 27.1 percent of all investigated riders. For riders killed in single or multiple-vehicle accidents, alcohol or drugs were found in 44.6 and 15.3 percent, respectively. Alcohol was the most frequently found substance for all age groups and most prevalent in samples from riders below 25 years who died in single-vehicle accidents (45.8 percent). Drugs were most often found among riders between 25 and 34 years (19.6 percent in total and 25.9% for those killed in single-vehicle crashes). The prevalence of alcohol or drugs was highest among riders killed in single-vehicle accidents during weekend days and nights (60.9 and 65.2 percent). Alcohol and drugs were less often found in samples from killed motorcycles riders than in samples from car and van drivers (40.2 percent). For single-vehicle accidents, the total prevalence of alcohol or drugs among killed motorcycles riders and car drivers was 44.6 percent and 63.8 percent, respectively. The same pattern of alcohol and drugs was found among the two groups, except that the prevalence among motorcycle riders was lower

  4. Physics Bus: An Innovative Model for Public Engagement

    Science.gov (United States)

    Fox, Claire

    The Physics Bus is about doing science for fun. It is an innovative model for science outreach whose mission is to awaken joy and excitement in physics for all ages and walks of life - especially those underserved by science enrichment. It is a mobile exhibition of upcycled appliances-reimagined by kids-that showcase captivating physics phenomena. Inside our spaceship-themed school bus, visitors will find: a microwave ionized-gas disco-party, fog rings that shoot from a wheelbarrow tire, a tv whose electron beam is controlled by a toy keyboard, and over 20 other themed exhibits. The Physics Bus serves a wide range of public in diverse locations from local neighborhoods, urban parks and rural schools, to cross-country destinations. Its approachable, friendly and relaxed environment allows for self-paced and self-directed interactions, providing a positive and engaging experience with science. We believe that this environment enriches lives and inspires people. In this presentation we will talk about the nuts and bolts that make this model work, how the project got started, and the resources that keep it going. We will talk about the advantages of being a grassroots and community-based organization, and how programs like this can best interface with universities. We will explain the benefits of focusing on direct interactions and why our model avoids ``teaching'' physics content with words. Situating our approach within a body of research on the value of informal science we will discuss our success in capturing and engaging our audience. By the end of this presentation we hope to broaden your perception of what makes a successful outreach program and encourage you to value and support alternative outreach models such as this one. In Collaboration with: Eva Luna, Cornell University; Erik Herman, Cornell University; Christopher Bell, Ithaca City School District.

  5. Bus Route Design with a Bayesian Network Analysis of Bus Service Revenues

    Directory of Open Access Journals (Sweden)

    Yi Liu

    2018-01-01

    Full Text Available A Bayesian network is used to estimate revenues of bus services in consideration of the effect of bus travel demands, passenger transport distances, and so on. In this research, the area X in Beijing has been selected as the study area because of its relatively high bus travel demand and, on the contrary, unsatisfactory bus services. It is suggested that the proposed Bayesian network approach is able to rationally predict the probabilities of different revenues of various route services, from the perspectives of both satisfying passenger demand and decreasing bus operation cost. This way, the existing bus routes in the studied area can be optimized for their most probable high revenues.

  6. Bus and Tag Terminators for IBM system/360

    CERN Multimedia

    Control units were connected to the channels with "Bus and Tag" cable pairs. The bus cables carried the address and data information and the tag cables identified what data was on the bus. There were three general types of bus-and-tag cables produced by IBM.

  7. PCISIM - A Simulation Tool for PCI Bus Based Systems

    DEFF Research Database (Denmark)

    Sharp, Robin

    1999-01-01

    This document describes a PCI bus simulator for use in evaluating the feasibility of system designs based on this bus.......This document describes a PCI bus simulator for use in evaluating the feasibility of system designs based on this bus....

  8. Large truck and bus crash facts, 2010.

    Science.gov (United States)

    2012-09-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2010. Selected crash statistics on passenger : vehicles are also presen...

  9. Large truck and bus crash facts, 2012.

    Science.gov (United States)

    2014-06-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2012. Selected crash statistics on passenger vehicles are also presented ...

  10. Large truck and bus crash facts, 2013.

    Science.gov (United States)

    2015-04-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2013. Selected crash statistics on passenger vehicles are also presented ...

  11. Large truck and bus crash facts, 2009.

    Science.gov (United States)

    2011-10-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2009. Selected crash statistics on passenger : vehicles are also presen...

  12. Large truck and bus crash facts, 2011.

    Science.gov (United States)

    2013-10-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2011. Selected crash statistics on passenger : vehicles are also presen...

  13. Passenger bus industry weather information application.

    Science.gov (United States)

    2011-03-21

    Adverse weather significantly affects the United States national transportation system, including commercial companies : that rely on highways to support their enterprises. The Passenger Bus (Motorcoach) Industry (PBI) is one such affected : user who...

  14. Understanding & modeling bus transit driver availability.

    Science.gov (United States)

    2014-07-01

    Bus transit agencies are required to hire extraboard (i.e. back-up) operators to account for unexpected absences. Incorrect sizing of extra driver workforce is problematic for a number of reasons. Overestimating the appropriate number of extraboard o...

  15. Bicycle-bus conflict area study.

    Science.gov (United States)

    2009-11-01

    Increasing bicycle use and bus ridership are both desirable policy goals : from a sustainability standpoint, but on city streets these two modes of : transport are often in conflict. While occupying opposite ends of the size : and weight spectrum, th...

  16. TMS communications software. Volume 2: Bus interface unit

    Science.gov (United States)

    Gregor, P. J.

    1979-01-01

    A data bus communication system to support the space shuttle's Trend Monitoring System (TMS) and to provide a basis for evaluation of the bus concept is described. Installation of the system included developing both hardware and software interfaces between the bus and the specific TMS computers and terminals. The software written for the microprocessor-based bus interface units is described. The software implements both the general bus communications protocol and also the specific interface protocols for the TMS computers and terminals.

  17. Comparison and status of 32 bit backplane bus architectures

    International Nuclear Information System (INIS)

    Muller, K.D.

    1985-01-01

    With the introduction of 32 bit microprocessors several new 32 bit backplane bus architectures have been developed and are in the process for standardization. Among these are Future Bus (IEEE P896.1), VME-Bus (IEEE 1014), MULTIBUS II, Nu-Bus and Fastbus (IEEE 960). The paper describes and compares the main features of these bus architectures and mentions the status of national and international standardization efforts

  18. The seated bus passenger--a review.

    Science.gov (United States)

    Levis, J A

    1978-09-01

    The paper describes the inter-relationship of anthropometry, rig studies and dynamic testing of aspects related to problems of the seated bus passenger. It seeks to draw together sub-sections of a very large study sponsored by the government through the Transport and Road Research Laboratory and undertaken by the Human Factors Group of Leyland Truck and Bus. It is relevant to all those designing passenger carrying transport systems.

  19. The Gozo discovery bus : a successful experiment

    OpenAIRE

    Vella, Maryrose

    2008-01-01

    The introduction of a tourist discovery bus in Gozo came about as a result of an EU Project which is part of the Interreg III B Archimed programmes in which the Islands and Small States Institute of the University of Malta participated. Other countries participating in this programme besides Malta, represented by the Islands and Small States Institute, are Italy, Cyprus and Greece. The discovery bus service was aimed at encouraging more tourists to come to Gozo and enabling them to visit stra...

  20. NOC AND BUS ARCHITECTURE: A COMPARISON

    OpenAIRE

    RAJEEV KAMAL; NEERAJ YADAV

    2012-01-01

    Network-on-chip designs promise to offer considerable advantages over the traditional bus-based architecture. As continuing scaling of Moore’s law enables ever greater transistor densities, design complexity, power limitations and application convergence networks have started to replace busses in much smaller systems and the enhancement of NoC. This paper summarizes the advantages of the NoC and the limitations of traditional bus based architecture. In this paper we discuss a detailed compari...

  1. Bus line classification using neural networks

    OpenAIRE

    Jiménez Alonso, Felipe; Serradilla García, Francisco; Román de Andrés, Alfonso; Naranjo Hernandez, Jose Eugenio

    2014-01-01

    Grouping urban bus routes is necessary when there are evidences of significant differences among them. In Jiménez et al. (2013), a reduced sample of routes was grouped into clusters utilizing kinematic measured data. As a further step, in this paper, the remaining urban bus routes of a city, for which no kinematic measurements are available, are classified. For such purpose we use macroscopic geographical and functional variables to describe each route, while the clustering process is perform...

  2. Borges & Bikes Riders: Toward an Understanding of Autoethnography

    Science.gov (United States)

    Wamsted, John O.

    2012-01-01

    In this article the author--a full-time high school mathematics teacher and concurrent doctoral candidate in Department of Middle-Secondary Education and Instructional Technology at Georgia State University--will make a case for the use of an autoethnographic methodological tool he is calling "narrative mining." He will begin by briefly…

  3. Common bus multinode sensor system

    International Nuclear Information System (INIS)

    Kelly, T.F.; Naviasky, E.H.; Evans, W.P.; Jefferies, D.W.; Smith, J.R.

    1988-01-01

    This patent describes a nuclear power plant including a common bus multinode sensor system for sensors in the nuclear power plant, each sensor producing a sensor signal. The system consists of: a power supply providing power; a communication cable coupled to the power supply; plural remote sensor units coupled between the cable and one or more sensors, and comprising: a direct current power supply, connected to the cable and converting the power on the cable into direct current; an analog-to-digital converter connected to the direct current power supply; an oscillator reference; a filter; and an integrated circuit sensor interface connected to the direct current power supply, the analog-to-digital converter, the oscillator crystal and the filter, the interface comprising: a counter receiving a frequency designation word from external to the interface; a phase-frequency comparator connected to the counter; an oscillator connected to the oscillator reference; a timing counter connected to the oscillator, the phase/frequency comparator and the analog-to-digital converter; an analog multiplexer connectable to the sensors and the analog-to-digital converter, and connected to the timing counter; a shift register operatively connected to the timing counter and the analog-to-digital converter; an encoder connected to the shift register and connectable to the filter; and a voltage controlled oscillator connected to the filter and the cable

  4. Vision-based measuring system for rider's pose estimation during motorcycle riding

    Science.gov (United States)

    Cheli, F.; Mazzoleni, P.; Pezzola, M.; Ruspini, E.; Zappa, E.

    2013-07-01

    Inertial characteristics of the human body are comparable with the vehicle ones in motorbike riding: the study of a rider's dynamic is a crucial step in system modeling. An innovative vision based system able to measure the six degrees of freedom of the driver with respect to the vehicle is proposed here: the core of the proposed approach is an image acquisition and processing technique capable of reconstructing the position and orientation of a target fixed on the rider's back. The technique is firstly validated in laboratory tests comparing measured and imposed target motion laws and successively tested in a real case scenario during track tests with amateur and professional drivers. The presented results show the capability of the technique to correctly describe the driver's dynamic, his interaction with the vehicle as well as the possibility to use the new measuring technique in the comparison of different driving styles.

  5. Keeping Your Eye on the Rail: Gaze Behaviour of Horse Riders Approaching a Jump

    Science.gov (United States)

    Hall, Carol; Varley, Ian; Kay, Rachel; Crundall, David

    2014-01-01

    The gaze behaviour of riders during their approach to a jump was investigated using a mobile eye tracking device (ASL Mobile Eye). The timing, frequency and duration of fixations on the jump and the percentage of time when their point of gaze (POG) was located elsewhere were assessed. Fixations were identified when the POG remained on the jump for 100 ms or longer. The jumping skill of experienced but non-elite riders (n = 10) was assessed by means of a questionnaire. Their gaze behaviour was recorded as they completed a course of three identical jumps five times. The speed and timing of the approach was calculated. Gaze behaviour throughout the overall approach and during the last five strides before take-off was assessed following frame-by-frame analyses. Differences in relation to both round and jump number were found. Significantly longer was spent fixated on the jump during round 2, both during the overall approach and during the last five strides (pJump 1 was fixated on significantly earlier and more frequently than jump 2 or 3 (pjump 3 than with jump 1 (p = 0.01) but there was no difference in errors made between rounds. Although no significant correlations between gaze behaviour and skill scores were found, the riders who scored higher for jumping skill tended to fixate on the jump earlier (p = 0.07), when the horse was further from the jump (p = 0.09) and their first fixation on the jump was of a longer duration (p = 0.06). Trials with elite riders are now needed to further identify sport-specific visual skills and their relationship with performance. Visual training should be included in preparation for equestrian sports participation, the positive impact of which has been clearly demonstrated in other sports. PMID:24846055

  6. Recruiting and maintaining dairy cooperative members :a strategy for reducing the free rider problem

    OpenAIRE

    Green, Kris R.

    1992-01-01

    Dairy marketing cooperatives provide marketwide services, such as lobbying for higher support prices and negotiating for premiums above marketing order prices, which benefit all dairy farmers in the market. The presence of free riders, people who benefit from these marketwide services without paying any of the costs of these services, can jeopardize the existence of the cooperative. Understanding why members were attracted to the cooperative and why independents (non-members) w...

  7. Mobile phone use among motorcyclists and electric bike riders: A case study of Hanoi, Vietnam.

    Science.gov (United States)

    Truong, Long T; Nguyen, Hang T T; De Gruyter, Chris

    2016-06-01

    Motorcyclist injuries and fatalities are a major concern of many developing countries. In Vietnam, motorcycles are involved in more than 70% of all road traffic crashes. This paper aims to explore the prevalence and factors associated with mobile phone use among motorcyclists and electric bike riders, using a case study of Hanoi, Vietnam. A cross-sectional observation survey was undertaken at 12 sites, in which each site was surveyed during a two-hour peak period from 16:30 to 18:30 for two weekdays and one weekend day. A total of 26,360 riders were observed, consisting of 24,759 motorcyclists and 1601 electric bike riders. The overall prevalence of mobile phone use while riding was 8.4% (95% CI: 8.06-8.74%) with calling having higher prevalence than screen operation: 4.64% (95% CI: 4.39-4.90%) vs. 3.76% (95% CI: 3.52-3.99%) respectively. Moreover, the prevalence of mobile phone use was higher among motorcyclists than electric bike riders: 8.66% (95%CI: 8.30-9.01%) vs. 4.43% (95% CI: 3.40-5.47%) respectively. Logistic regression analyses revealed that mobile phone use while riding was associated with vehicle type, age, gender, riding alone, weather, day of week, proximity to city centre, number of lanes, separate car lanes, red traffic light duration, and police presence. Combining greater enforcement of existing legislations with extensive education and publicity programs is recommended to reduce potential deaths and injuries related to the use of mobile phones while riding. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. The streetboard rider: an appealing problem in non-holonomic mechanics

    International Nuclear Information System (INIS)

    Janova, J; Musilova, J

    2010-01-01

    This paper enlarges the reservoir of solved tutor problems in non-holonomic mechanics at the undergraduate level of physics education. Unlike other, rather artificial, solved problems typically used, the streetboard-rider locomotion problem presented here represents an appealing contemporary real-world problem with interesting applications in a popular sport and in robotics. In this paper, the streetboard motion is discussed from the physical point of view. We show that the interesting snake-like motion performed by streetboard riders stems from its non-holonomic nature. The related non-holonomic constraints are derived and the problem of the mechanical system subjected to these non-holonomic constraints is solved using methods appropriate to the undergraduate university level. The analytical solution for the circular motion and the numerical solution for the general motion are obtained, the physical meaning of the derived constrained forces is investigated and the results are discussed with respect to observed streetboard-rider locomotion. The brief outline of the paper can be used as a demonstration example in non-holonomic mechanics lessons, while the paper itself establishes an original undergraduate computational student project in theoretical mechanics.

  9. Privacy-Preserving Billing Scheme against Free-Riders for Wireless Charging Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Xingwen Zhao

    2017-01-01

    Full Text Available Recently, scientists in South Korea developed on-line electric vehicle (OLEV, which is a kind of electric vehicle that can be charged wirelessly while it is moving on the road. The battery in the vehicle can absorb electric energy from the power transmitters buried under the road without any contact with them. Several billing schemes have been presented to offer privacy-preserving billing for OLEV owners. However, they did not consider the existence of free-riders. When some vehicles are being charged after showing the tokens, vehicles that are running ahead or behind can switch on their systems and drive closely for a free charging. We describe a billing scheme against free-riders by using several cryptographic tools. Each vehicle should authenticate with a compensation-prepaid token before it can drive on the wireless-charging-enabled road. The service provider can obtain compensation if it can prove that certain vehicle is a free-rider. Our scheme is privacy-preserving so the charging will not disclose the locations and routine routes of each vehicle. In fact, our scheme is a fast authentication scheme that anonymously authenticates each user on accessing a sequence of services. Thus, it can be applied to sequential data delivering services in future 5G systems.

  10. The streetboard rider: an appealing problem in non-holonomic mechanics

    Energy Technology Data Exchange (ETDEWEB)

    Janova, J [Department of Statistics and Operation Analysis, Faculty of Business and Economics Mendel University, Zemedelska 1, 61300 Brno (Czech Republic); Musilova, J [Department of Theoretical Physics and Astrophysics, Faculty of Science, Masaryk University, Kotlarska 2, 611 37 Brno (Czech Republic)], E-mail: janova@physics.muni.cz

    2010-03-15

    This paper enlarges the reservoir of solved tutor problems in non-holonomic mechanics at the undergraduate level of physics education. Unlike other, rather artificial, solved problems typically used, the streetboard-rider locomotion problem presented here represents an appealing contemporary real-world problem with interesting applications in a popular sport and in robotics. In this paper, the streetboard motion is discussed from the physical point of view. We show that the interesting snake-like motion performed by streetboard riders stems from its non-holonomic nature. The related non-holonomic constraints are derived and the problem of the mechanical system subjected to these non-holonomic constraints is solved using methods appropriate to the undergraduate university level. The analytical solution for the circular motion and the numerical solution for the general motion are obtained, the physical meaning of the derived constrained forces is investigated and the results are discussed with respect to observed streetboard-rider locomotion. The brief outline of the paper can be used as a demonstration example in non-holonomic mechanics lessons, while the paper itself establishes an original undergraduate computational student project in theoretical mechanics.

  11. Security awareness for public bus transportation : case studies of attacks against the Israeli public bus system.

    Science.gov (United States)

    2012-03-01

    This report presents 16 case studies of attacks planned or carried out against Israeli bus targets, along with statistical data on the number, frequency, and lethality of attacks against bus targets that have taken place in Israel since 1970 and duri...

  12. 77 FR 6178 - FY 2012 Discretionary Funding Opportunities: Bus and Bus Facilities Programs (State of Good...

    Science.gov (United States)

    2012-02-07

    ... not limited to: Rail, ferry, intercity bus and private transportation providers. In order to be..., intercity bus, and private transportation providers. In order to be eligible for funding, intermodal... automobile travel, improving the pedestrian environment of a community or, use of environmental design...

  13. Digital processing data communication systems (bus systems). Digitale Prozessdaten-Kommunikations-Systeme (Bus Systeme)

    Energy Technology Data Exchange (ETDEWEB)

    Fleck, K

    1980-01-01

    After an introduction to the technology of digital processing data communication systems there are the following chapters: digital communication of processing data in automation technology, the technology of biserial communication, the implementaiton of a bus system, the data transmission of the TDC-2000 system of Honeywell's and the process bus CS 275 in the automation system TELEPERM M of Siemens AG.

  14. Dynamic Bus Travel Time Prediction Models on Road with Multiple Bus Routes

    Science.gov (United States)

    Bai, Cong; Peng, Zhong-Ren; Lu, Qing-Chang; Sun, Jian

    2015-01-01

    Accurate and real-time travel time information for buses can help passengers better plan their trips and minimize waiting times. A dynamic travel time prediction model for buses addressing the cases on road with multiple bus routes is proposed in this paper, based on support vector machines (SVMs) and Kalman filtering-based algorithm. In the proposed model, the well-trained SVM model predicts the baseline bus travel times from the historical bus trip data; the Kalman filtering-based dynamic algorithm can adjust bus travel times with the latest bus operation information and the estimated baseline travel times. The performance of the proposed dynamic model is validated with the real-world data on road with multiple bus routes in Shenzhen, China. The results show that the proposed dynamic model is feasible and applicable for bus travel time prediction and has the best prediction performance among all the five models proposed in the study in terms of prediction accuracy on road with multiple bus routes. PMID:26294903

  15. Dynamic Bus Travel Time Prediction Models on Road with Multiple Bus Routes.

    Science.gov (United States)

    Bai, Cong; Peng, Zhong-Ren; Lu, Qing-Chang; Sun, Jian

    2015-01-01

    Accurate and real-time travel time information for buses can help passengers better plan their trips and minimize waiting times. A dynamic travel time prediction model for buses addressing the cases on road with multiple bus routes is proposed in this paper, based on support vector machines (SVMs) and Kalman filtering-based algorithm. In the proposed model, the well-trained SVM model predicts the baseline bus travel times from the historical bus trip data; the Kalman filtering-based dynamic algorithm can adjust bus travel times with the latest bus operation information and the estimated baseline travel times. The performance of the proposed dynamic model is validated with the real-world data on road with multiple bus routes in Shenzhen, China. The results show that the proposed dynamic model is feasible and applicable for bus travel time prediction and has the best prediction performance among all the five models proposed in the study in terms of prediction accuracy on road with multiple bus routes.

  16. Classifying the Diversity of Bus Mapping Systems

    Science.gov (United States)

    Said, Mohd Shahmy Mohd; Forrest, David

    2018-05-01

    This study represents the first stage of an investigation into understanding the nature of different approaches to mapping bus routes and bus network, and how they may best be applied in different public transport situations. In many cities, bus services represent an important facet of easing traffic congestion and reducing pollution. However, with the entrenched car culture in many countries, persuading people to change their mode of transport is a major challenge. To promote this modal shift, people need to know what services are available and where (and when) they go. Bus service maps provide an invaluable element of providing suitable public transport information, but are often overlooked by transport planners, and are under-researched by cartographers. The method here consists of the creation of a map evaluation form and performing assessment of published bus networks maps. The analyses were completed by a combination of quantitative and qualitative data analysis of various aspects of cartographic design and classification. This paper focuses on the resulting classification, which is illustrated by a series of examples. This classification will facilitate more in depth investigations into the details of cartographic design for such maps and help direct areas for user evaluation.

  17. VICbus: A standard inter-crate bus

    International Nuclear Information System (INIS)

    Parkman, C.F.

    1990-01-01

    VICbus is a standard inter-crate cable bus being developed by a working group of the ISO/IEC. Derived from an initiative of the VMEbus Working Group of ESONE, VICbus aims to provide users of multi-crate VMEbus and other backplane bus systems with a standard inter-crate connection. Multi-drop operation is provided for up to 31 devices on a cable of maximum 100 metres in length. Two data transfer protocols are specified, compelled (asynchronous) transfers for transparent interconnection of backplane bus systems (VMEbus in the first instance), and high-speed, non-compelled (synchronous) transfers between VICbus interfaces. A limited interrupt mechanism is specified, as well as simple, but efficient arbitration technique. Conventional technology is employed: copper cables, existing transcievers, and differential signal transmission, together with proven low-level protocols. Data transfer rates in excess of 30 Mbyte/s will be possible on a cable length of 30 metres

  18. A comparison of the hazard perception ability of accident-involved and accident-free motorcycle riders.

    Science.gov (United States)

    Cheng, Andy S K; Ng, Terry C K; Lee, Hoe C

    2011-07-01

    Hazard perception is the ability to read the road and is closely related to involvement in traffic accidents. It consists of both cognitive and behavioral components. Within the cognitive component, visual attention is an important function of driving whereas driving behavior, which represents the behavioral component, can affect the hazard perception of the driver. Motorcycle riders are the most vulnerable types of road user. The primary purpose of this study was to deepen our understanding of the correlation of different subtypes of visual attention and driving violation behaviors and their effect on hazard perception between accident-free and accident-involved motorcycle riders. Sixty-three accident-free and 46 accident-involved motorcycle riders undertook four neuropsychological tests of attention (Digit Vigilance Test, Color Trails Test-1, Color Trails Test-2, and Symbol Digit Modalities Test), filled out the Chinese Motorcycle Rider Driving Violation (CMRDV) Questionnaire, and viewed a road-user-based hazard situation with an eye-tracking system to record the response latencies to potentially dangerous traffic situations. The results showed that both the divided and selective attention of accident-involved motorcycle riders were significantly inferior to those of accident-free motorcycle riders, and that accident-involved riders exhibited significantly higher driving violation behaviors and took longer to identify hazardous situations compared to their accident-free counterparts. However, the results of the regression analysis showed that aggressive driving violation CMRDV score significantly predicted hazard perception and accident involvement of motorcycle riders. Given that all participants were mature and experienced motorcycle riders, the most plausible explanation for the differences between them is their driving style (influenced by an undesirable driving attitude), rather than skill deficits per se. The present study points to the importance of

  19. The Bus Station Spacing Optimization Based on Game Theory

    Directory of Open Access Journals (Sweden)

    Changjiang Zheng

    2015-01-01

    Full Text Available With the development of city, the problem of traffic is becoming more and more serious. Developing public transportation has become the key to solving this problem in all countries. Based on the existing public transit network, how to improve the bus operation efficiency, and reduce the residents transit trip cost has become a simple and effective way to develop the public transportation. Bus stop spacing is an important factor affecting passengers’ travel time. How to set up bus stop spacing has become the key to reducing passengers’ travel time. According to comprehensive traffic survey, theoretical analysis, and summary of urban public transport characteristics, this paper analyzes the impact of bus stop spacing on passenger in-bus time cost and out-bus time cost and establishes in-bus time and out-bus time model. Finally, the paper gets the balance best station spacing by introducing the game theory.

  20. Bus accident severity and passenger injury: evidence from Denmark

    DEFF Research Database (Denmark)

    Prato, Carlo Giacomo; Kaplan, Sigal

    2014-01-01

    Purpose Bus safety is a concern not only in developing countries, but also in the U.S. and Europe. In Denmark, disentangling risk factors that are positively or negatively related to bus accident severity and injury occurrence to bus passengers can contribute to promote safety as an essential...... principle of sustainable transit and advance the vision “every accident is one too many”. Methods Bus accident data were retrieved from the national accident database for the period 2002–2011. A generalized ordered logit model allows analyzing bus accident severity and a logistic regression enables...... examining occurrence of injury to bus passengers. Results Bus accident severity is positively related to (i) the involvement of vulnerable road users, (ii) high speed limits, (iii) night hours, (iv) elderly drivers of the third party involved, and (v) bus drivers and other drivers crossing in yellow or red...

  1. Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus Preliminary Evaluation Results

    Science.gov (United States)

    2008-10-16

    This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The report discusses the planned fuel cell bus demonstration and equipment us...

  2. Request-Centric Wireless Bus Information Management System

    Directory of Open Access Journals (Sweden)

    Ying-Chih Chen

    2016-11-01

    Full Text Available This invention relates to a wireless bus information management system, which includes bus stop and vehicle management subsystems. The management signals are transmittable between bus stops and the vehicle. Based on vehicle management signals, the bus stop management subsystem can obtain information about the bus route identification, the number of unoccupied seats, the intention to stop or not, etc. Similarly, with the bus stop management signals, the vehicle management subsystem can make the decision of stopping. Accordingly, when a passenger wants to get off the vehicle or there are unoccupied seats, the vehicle management subsystem will inform the bus stop management subsystem such that the passengers waiting at the bus stop may flexibly schedule their travel plan. The proposed distributed wireless system is detailed by a prototype implementation and a simulation analysis, which is shown to be feasible and scalable.

  3. Negotiating Left-Hand and Right-Hand Bends: A Motorcycle Simulator Study to Investigate Experiential and Behaviour Differences Across Rider Groups

    Science.gov (United States)

    Crundall, Elizabeth; Crundall, David; Stedmon, Alex W.

    2012-01-01

    Why do motorcyclists crash on bends? To address this question we examined the riding styles of three groups of motorcyclists on a motorcycle simulator. Novice, experienced and advanced motorcyclists navigated a series of combined left and right bends while their speed and lane position were recorded. Each rider encountered an unexpected hazard on both a left- and right-hand bend section. Upon seeing the hazards, all riders decreased their speed before steering to avoid the hazard. Experienced riders tended to follow more of a racing line through the bends, which resulted in them having to make the most severe changes to their position to avoid a collision. Advanced riders adopted the safest road positions, choosing a position which offered greater visibility through the bends. As a result, they did not need to alter their road position in response to the hazard. Novice riders adopted similar road positions to experienced riders on the left-hand bends, but their road positions were more similar to advanced riders on right-hand bends, suggesting that they were more aware of the risks associated with right bends. Novice riders also adopted a safer position on post-hazard bends whilst the experienced riders failed to alter their behaviour even though they had performed the greatest evasive manoeuvre in response to the hazards. Advanced riders did not need to alter their position as their approach to the bends was already optimal. The results suggest that non-advanced riders were more likely to choose an inappropriate lane position than an inappropriate speed when entering a bend. Furthermore, the findings support the theory that expertise is achieved as a result of relearning, with advanced training overriding ‘bad habits’ gained through experience alone. PMID:22253845

  4. Analysis of a diesel-electric hybrid urban bus system

    Science.gov (United States)

    Marr, W. W.; Sekar, R. R.; Ahlheim, M. C.

    A hybrid bus powered by a diesel engine and a battery pack was analyzed over an idealized bus-driving cycle in Chicago. Three hybrid configurations, two parallel and one series, were evaluated. The results indicate that the fuel economy of a hybrid bus, taking into account the regenerative braking, is comparable with that of a conventional diesel bus. Life-cycle costs are slightly higher because of the added weight and cost of the battery.

  5. Injury Source and Correlation Analysis of Riders in Car-Electric Bicycle Accidents

    Directory of Open Access Journals (Sweden)

    Tiefang Zou

    2018-01-01

    Full Text Available The knowledge about the injury source and correlation of riders in car-electric bicycle accident will be helpful in the cross validation of traces and vehicle safety design. In order to know more information about such kind of knowledge, 57 true car-electric bicycle accidents were reconstructed by PC-Crash and then data on injury information of riders were collected directly from the reconstructed cases. These collected data were validated by some existing research results firstly, and then 4 abnormal cases were deleted according to the statistical method. Finally, conclusions can be obtained according to the data obtained from the remaining 53 cases. Direct injuries of the head and right leg are from the road pavement upon low speed; the source laws of indirect head injuries are not obvious. Upon intermediate and high speed, the injuries of the above parts are from automobiles. Injuries of the left leg, femur, and right knee are from automobiles; left knee injuries are from automobiles, the road pavement and automobiles, respectively, upon low, intermediate, and high speed. The source laws of indirect torso injuries are not obvious upon intermediate and low speed, which are from automobiles upon high speed, while direct torso injuries are from the road pavement. And there is no high correlation between all parts of the injury of riders. The largest correlation coefficient was the head-left femur and left femur-right femur, which was 0.647, followed by the head-right femur (0.638 and head-torso which was 0.617.

  6. Injury Source and Correlation Analysis of Riders in Car-Electric Bicycle Accidents.

    Science.gov (United States)

    Zou, Tiefang; Yi, Liang; Cai, Ming; Hu, Lin; Li, Yuelin

    2018-01-01

    The knowledge about the injury source and correlation of riders in car-electric bicycle accident will be helpful in the cross validation of traces and vehicle safety design. In order to know more information about such kind of knowledge, 57 true car-electric bicycle accidents were reconstructed by PC-Crash and then data on injury information of riders were collected directly from the reconstructed cases. These collected data were validated by some existing research results firstly, and then 4 abnormal cases were deleted according to the statistical method. Finally, conclusions can be obtained according to the data obtained from the remaining 53 cases. Direct injuries of the head and right leg are from the road pavement upon low speed; the source laws of indirect head injuries are not obvious. Upon intermediate and high speed, the injuries of the above parts are from automobiles. Injuries of the left leg, femur, and right knee are from automobiles; left knee injuries are from automobiles, the road pavement and automobiles, respectively, upon low, intermediate, and high speed. The source laws of indirect torso injuries are not obvious upon intermediate and low speed, which are from automobiles upon high speed, while direct torso injuries are from the road pavement. And there is no high correlation between all parts of the injury of riders. The largest correlation coefficient was the head-left femur and left femur-right femur, which was 0.647, followed by the head-right femur (0.638) and head-torso which was 0.617.

  7. Cleaner generation, free-riders, and environmental integrity: clean development mechanism and the power sector

    Energy Technology Data Exchange (ETDEWEB)

    Bernow, Stephen; Kartha, Sivan; Lazarus, Michael; Page, Tom [Tellus Institute and Stockholm Environmental Institute-Boston Center, Boston, MA (United States)

    2001-06-01

    This article provides a first-cut estimate of the potential impacts of the clean development mechanism (CDM) on electricity generation and carbon emissions in the power sector of non-Annex 1 countries. We construct four illustrative CDM regimes that represent a range of approaches under consideration within the climate community. We examine the impact of these CDM regimes on investments in new generation, under illustrative carbon trading prices of US$ 10 and 100/tC. In the cases that are most conductive to CDM activity, roughly 94% of new generation investments remains identical to the without-CDM situation, with only 6% shifting from higher to lower carbon intensity technologies. We estimate that the CDM would bolster renewable energy generation by as little as 15% at US$ 10/tC, or as much as 300% at US$ 100/tC. A striking finding comes from our examination of the potential magnitude of the 'free-rider' problem, i.e. crediting of activities that will occur even in the absence of the CDM. The CDM is intended to be globally carbon-neutral --- a project reduces emissions in the host country but generates credits that increase emissions in the investor country. However, to the extent that unwarranted credits are awarded to non-additional projects, the CDM would increase global carbon emissions above the without-CDM emissions level. Under two of the CDM regimes considered, cumulative free-riders credits total 250-600MtC through the end of the first budget period in 2012. This represents 10-23% of the likely OECD emissions reduction requirement during the first budget period. Since such a magnitude of free-rider credits from non-additional CDM projects could threaten the environmental integrity of the Kyoto protocol, it is imperative that policy makers devise CDM rules that encourage legitimate projects, while effectively screening out non-additional activities. (Author)

  8. Security awareness for public bus transportation : case studies of attacks against the Israeli public bus system [research brief].

    Science.gov (United States)

    2012-03-01

    Government regulators and transportation operators of public bus systems are concerned about terrorist attacks. Bus attacks in Israel between late September 2000 and the end of 2006, a period known as the Second Intifada, are particularly well known....

  9. A review on bicycle and motorcycle rider control with a perspective on handling qualities

    Science.gov (United States)

    Kooijman, J. D. G.; Schwab, A. L.

    2013-11-01

    This paper is a review study on handling and control of bicycles and motorcycles, the so-called single-track vehicles. The first part gives a brief overview on the modelling of the dynamics of single-track vehicles and the experimental validation. The second part focusses on a review of modelling and measuring human rider control. The third part deals with the concepts of handling and manoeuvrability and their experimental validation. Parallels are drawn with the literature on aircraft handling and pilot models. The paper concludes with the open ends and promising directions for future work in the field of handling and control of single-track vehicles.

  10. Road traffic injuries among riders of electric bike/electric moped in southern China.

    Science.gov (United States)

    Zhang, Xujun; Yang, Yaming; Yang, Jie; Hu, Jie; Li, Yang; Wu, Ming; Stallones, Lorann; Xiang, Henry

    2018-05-19

    Electric bike/moped-related road traffic injuries have become a burgeoning public health problem in China. The objective of this study was to identify the prevalence and potential risk factors of electric bike/moped-related road traffic injuries among electric bike/moped riders in southern China. A cross-sectional study was used to interview 3,151 electric bike/moped riders in southern China. Electric bike/moped-related road traffic injuries that occurred from July 2014 to June 2015 were investigated. Data were collected by face-to-face interviews and analyzed between July 2015 and June 2017. The prevalence of electric bike/moped-related road traffic injuries among the investigated riders was 15.99%. Electric bike/moped-related road traffic injuries were significantly associated with category of electric bike (adjusted odds ratio [AOR] = 1.36, 95% confidence interval [CI], 1.01-1.82), self-reported confusion (AOR = 1.77, 95% CI, 1.13-2.78), history of crashes (AOR = 6.14, 95% CI, 4.68-8.07), running red lights (AOR = 3.57, 95% CI, 2.42-5.25), carrying children while riding (AOR = 1.96, 95% CI, 1.37-2.85), carrying adults while riding (AOR = 1.68, 95% CI, 1.23-2.28), riding in the motor lane (AOR = 2.42, 95% CI, 1.05-3.93), and riding in the wrong traffic direction (AOR = 1.63, 95% CI, 1.13-2.35). In over 77.58% of electric bike/moped-related road traffic crashes, riders were determined by the police to be responsible for the crash. Major crash-causing factors included violating traffic signals or signs, careless riding, speeding, and riding in the wrong lane. Traffic safety related to electric bikes/moped is becoming more problematic with growing popularity compared with other 2-wheeled vehicles. Programs need to be developed to prevent electric bike/moped-related road traffic injuries in this emerging country.

  11. 76 FR 68819 - State of Good Repair Bus and Bus Facilities Discretionary Program Funds

    Science.gov (United States)

    2011-11-07

    ... Availability on June 24, 2011. The SGR Initiative makes funds available to public transit providers to finance capital projects to replace, rehabilitate, and purchase buses and related equipment and to construct bus...

  12. 76 FR 37393 - FY 2011 Discretionary Livability Funding Opportunity; Section 5309 Bus and Bus Facilities...

    Science.gov (United States)

    2011-06-27

    ... 90 percent Federal share for the total cost of a biodiesel bus. The Act also allows a 90 percent... transit systems or roadways. iv. Will improve accessibility and transport services for economically...

  13. An Experimental Platform for Autonomous Bus Development

    Directory of Open Access Journals (Sweden)

    Héctor Montes

    2017-11-01

    Full Text Available Nowadays, with highly developed instrumentation, sensing and actuation technologies, it is possible to foresee an important advance in the field of autonomous and/or semi-autonomous transportation systems. Intelligent Transport Systems (ITS have been subjected to very active research for many years, and Bus Rapid Transit (BRT is one area of major interest. Among the most promising transport infrastructures, the articulated bus is an interesting, low cost, high occupancy capacity and friendly option. In this paper, an experimental platform for research on the automatic control of an articulated bus is presented. The aim of the platform is to allow full experimentation in real conditions for testing technological developments and control algorithms. The experimental platform consists of a mobile component (a commercial articulated bus fully instrumented and a ground test area composed of asphalt roads inside the Consejo Superior de Investigaciones Científicas (CSIC premises. This paper focuses also on the development of a human machine interface to ease progress in control system evaluation. Some experimental results are presented in order to show the potential of the proposed platform.

  14. Bus safety study : a report to Congress.

    Science.gov (United States)

    2013-11-01

    Section 20021(b) of the Moving Ahead for Progress for the 21st Century (MAP-21) legislation requires the Secretary of Transportation : to submit a report of the results of a Bus Safety Study to the Committee on Banking, Housing, and Urban Affai...

  15. Technology Validation: Fuel Cell Bus Evaluations

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, Leslie [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2018-01-02

    This presentation describing the FY 2016 accomplishments for the National Renewable Energy Laboratory's Fuel Cell Bus Evaluations project was presented at the U.S. Department of Energy Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Meeting, June 7, 2016.

  16. Repeater For A Digital-Communication Bus

    Science.gov (United States)

    Torres-Guzman, Esteban; Olson, Stephen; Heaps, Tim

    1993-01-01

    Digital repeater circuit designed to extend range of communication on MIL-STD-1553 bus beyond original maximum allowable length of 300 ft. Circuit provides two-way communication, one way at time, and conforms to specifications of MIL-STD-1553. Crosstalk and instability eliminated.

  17. Energy DataBus (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2013-07-01

    NREL has developed the Energy DataBus, an open-sourced software that collects massive amounts of energy-related data at second-to-second intervals; stores it in a massive, scalable database; and turns it into useful information.

  18. Obese motorcycle riders have a different injury pattern and longer hospital length of stay than the normal-weight patients.

    Science.gov (United States)

    Liu, Hang-Tsung; Rau, Cheng-Shyuan; Wu, Shao-Chun; Chen, Yi-Chun; Hsu, Shiun-Yuan; Hsieh, Hsiao-Yun; Hsieh, Ching-Hua

    2016-04-14

    The adverse effects of obesity on the physical health have been extensively studied in the general population, but not in motorcycle riders (includes both drivers and pillions). The aim of this study was to compare injury patterns, injury severities, mortality rates, and in-hospital or intensive care unit (ICU) length of stay (LOS) between obese and normal-weight patients who were hospitalized for the treatment of trauma following motorcycle accidents in a level I trauma center. Detailed data of 466 obese adult patients with a body mass index (BMI) ≥30 kg/m(2) and 2701 normal-weight patients (25 > BMI ≥18.5 kg/m(2)) who had sustained motorcycle accident-related injuries were retrieved from the Trauma Registry System between January 1, 2009 and December 31, 2013. We used the Pearson's chi-squared test, Fisher's exact test, and independent Student's t-test to analyze differences between the two groups. Compared to normal-weight motorcycle riders, more obese riders were men and drivers as opposed to pillions. In addition, fewer obese motorcycle riders showed alcohol intoxication. Analyses of the patients' Abbreviated Injury Scale (AIS) scores revealed that obese motorcycle riders presented with a higher rate of injury to the thorax, but a lower rate of injury to the face than normal-weight patients. In addition, obese motorcycle riders had a 2.7-fold greater incidence of humeral, 1.9-fold greater incidence of pelvic, and 1.5-fold greater incidence of rib fractures. In contrast, normal-weight motorcycle riders sustained a significantly higher rate of maxillary and clavicle fractures. Obese motorcycle riders had a significant longer in-hospital LOS than normal-weight motorcycle riders did (10.6 days vs. 9.5 days, respectively; p = 0.044), with an increase in in-hospital LOS of 0.82 days associated with every 10-unit increase in BMI. No statistically significant differences in Injury Severity Score (ISS), New Injury Severity Score (NISS), Trauma

  19. Stochastic Bus Dispatching Model untuk Optimalisasi Jumlah Bus Transjakarta Koridor 3

    Directory of Open Access Journals (Sweden)

    Zahedi Zahedi

    2011-12-01

    Full Text Available The increasing number of road user causing traffic jam finds out a way, busway. However, in its implementation, the number of fleet available does not enough to take the passengers. It results in the an amassed of passengers at several bus stops. This leads to passenger dissatisfaction satisfaction which eventually causes Transjakarta users to reuse private cars. Definitely this situation may builds up traffic jams. Stochastic Bus Dispatching Model is used to simulate public transportation that operates regularly. 

  20. Inroads into Equestrian Safety: Rider-Reported Factors Contributing to Horse-Related Accidents and Near Misses on Australian Roads

    Science.gov (United States)

    Thompson, Kirrilly; Matthews, Chelsea

    2015-01-01

    Simple Summary Riding horses on roads can be dangerous, but little is known about accidents and near misses. To explore road safety issues amongst Australian equestrians, we conducted an online survey. More than half of all riders (52%) reported having experienced at least one accident or near miss in the 12 months prior to the survey, mostly attributed to speed. Whilst our findings confirmed factors identified overseas, we also identified issues around road rules, hand signals and road rage. This paper suggests strategies for improving the safety of horses, riders and other road users. Abstract Horse riding and horse-related interactions are inherently dangerous. When they occur on public roads, the risk profile of equestrian activities is complicated by interactions with other road users. Research has identified speed, proximity, visibility, conspicuity and mutual misunderstanding as factors contributing to accidents and near misses. However, little is known about their significance or incidence in Australia. To explore road safety issues amongst Australian equestrians, we conducted an online survey. More than half of all riders (52%) reported having experienced at least one accident or near miss in the 12 months prior to the survey. Whilst our findings confirm the factors identified overseas, we also identified issues around rider misunderstanding of road rules and driver misunderstanding of rider hand signals. Of particular concern, we also found reports of potentially dangerous rider-directed road rage. We identify several areas for potential safety intervention including (1) identifying equestrians as vulnerable road users and horses as sentient decision-making vehicles; (2) harmonising laws regarding passing horses; (3) mandating personal protective equipment; (4) improving road signage; (5) comprehensive data collection; (6) developing mutual understanding amongst road-users; (7) safer road design and alternative riding spaces; and (8) increasing investment

  1. Shuttle bus services quality assessment Tangerang Selatan toward smart city

    Science.gov (United States)

    Fassa, Ferdinand; Sitorus, Fredy Jhon Philip; Adikesuma, Tri Nugraha

    2017-11-01

    Around the world, shuttle bus operation played the significant role to accommodate transportation for commuting bus passengers. Shuttle Bus services in cities are provided by various bus agencies with kinds of own specific purposes. For instance, at Tangerang Selatan, Indonesia, it was said that shuttle bus In Trans Bintaro is run and operated by private bus companies hire by Bintaro developer. The aim of this research is to identify factors of satisfaction of shuttle bus service in Kota Tangerang Selatan, Indonesia. Several factors are used to analyze sums of 20 parameters performance indicators of Shuttle Bus. A face to face interview using a questionnaire (N=200) was used to collect data on October and March 2017. Likert and diagram Cartesian were used to model the all the parameters. This research succeeded in finding some categories of Shuttle bus service attributes such as accessibility, comfort, and safety. Users agreed that eight indicators in shuttle bus have the excellent achievement, while three indicators on performance remain low and should receive more attention especially punctuality of the bus.

  2. Taking Physics and Now the Stars on the Road With the Magic Physics Bus

    Science.gov (United States)

    Bennum, David

    2009-05-01

    In February 2003 the ``Physics on the Road'' workshop, held at Colorado State University- Fort Collins, Colorado, brought together physics faculty who were experienced in designing and providing year --round mobile physics displays and those who were interested in initiating similar outreach programs. The impetus for the workshop was the upcoming ``World Year of Physics'', but the workshop had much broader impact for many of us who attended. The University of Nevada had a long history of demonstration shows for campus visitors from K-12 students/faculty but the cost of field trips began to limit this for many schools, especially for schools in poorer neighborhoods without large scale parental fundraising. The timing of the workshop was perfect for my developing program to utilize a donated ``electric bus'' as a traveling physics demo showcase. The program has grown to near our current limitations (70 mile range of the bus and time considerations), however we are expanding the ``scope'' of the project to include evening astronomy ``star parties'' as we enter the ``Year of Astronomy''. In addition to the bus transport of portable astronomy equipment to school sites we are adding, through donation, a 22 inch telescope in a domed observatory at a secondary campus location at the edge of Reno where large scale ``star parties'' can be conducted as outreach to K-12 and the community. The ``Physics on the Road'' bus reaches several thousand elementary and middle school students every year now and the potential for similar outreach with ``Stars on the Road'' has excited several of our faculty and physics students into increased participation in these endeavors to introduce our young people to science. It has become one of our most active ``recruitment'' plans and growing numbers of local students entering physics and other science majors is anecdotal evidence of success.

  3. VME bus based microcomputer system boards

    International Nuclear Information System (INIS)

    Chandra, A.K.; Ganesh, G.; Mayya, Anuradha; Chachondia, A.S.; Premraj, M.K.

    1991-01-01

    Several operator information systems for nuclear plants has been developed in the Division and these have involved extensive use of microcomputer boards for achieving various functions. Standard VME bus based boards have been developed to provide the most used functions. These boards have been fabricated and tested and used in several systems including Channel Temperature Monitoring systems, Disturbance Recording Systems etc. and are also proposed to be used in additional systems under developement. The use of standard bus and boards provides considerable savings in engineering time, prototyping, testing and evaluation costs, and maintenance support. This report desribes the various boards developed and the functions available on each. (author). 4 refs., 11 figs., 3 appendixes

  4. Exposure Assessment of Diesel Bus Emissions

    Directory of Open Access Journals (Sweden)

    Werner Hofmann

    2006-12-01

    Full Text Available The goal of this study was to measure ultrafine particle concentrations with diameters less than 1 μm emitted by diesel buses and to assess resulting human exposure levels. The study was conducted at the Woolloongabba Busway station in Brisbane, Australia in the winter months of 2002 during which temperature inversions frequently occurred. Most buses that utilize the station are fuelled by diesel, the exhaust of which contains a significant quantity of particle matter. Passengers waiting at the station are exposed to these particles emitted from the buses. During the course of this study, passenger census was conducted, based on video surveillance, yielding person-by-person waiting time data. Furthermore, a bus census revealed accurate information about the total number of diesel versus Compressed Natural Gas (CNG powered buses. Background (outside of the bus station and platform measurements of ultrafine particulate number size distributions were made to determine ambient aerosol concentrations. Particle number exposure concentration ranges from 10 and 40 to 60% of bus related exhaust fumes. This changes dramatically when considering the particle mass exposure concentration, where most passengers are exposed to about 50 to 80% of exhaust fumes. The obtained data can be very significant for comparison with similar work of this type because it is shown in previous studies that exhaust emissions causes cancer in laboratory animals. It was assumed that significant differences between platform and background distributions were due to bus emissions which, combined with passenger waiting times, yielded an estimate of passenger exposure to ultrafine particles from diesel buses. From an exposure point of view, the Busway station analyzed resembles a street canyon. Although the detected exhaust particle concentration at the outbound platform is found to be in the picogram range, exposure increases with the time passengers spend on the platform

  5. Inroads into Equestrian Safety: Rider-Reported Factors Contributing to Horse-Related Accidents and Near Misses on Australian Roads

    Directory of Open Access Journals (Sweden)

    Kirrilly Thompson

    2015-07-01

    Full Text Available Horse riding and horse-related interactions are inherently dangerous. When they occur on public roads, the risk profile of equestrian activities is complicated by interactions with other road users. Research has identified speed, proximity, visibility, conspicuity and mutual misunderstanding as factors contributing to accidents and near misses. However, little is known about their significance or incidence in Australia. To explore road safety issues amongst Australian equestrians, we conducted an online survey. More than half of all riders (52% reported having experienced at least one accident or near miss in the 12 months prior to the survey. Whilst our findings confirm the factors identified overseas, we also identified issues around rider misunderstanding of road rules and driver misunderstanding of rider hand signals. Of particular concern, we also found reports of potentially dangerous rider-directed road rage. We identify several areas for potential safety intervention including (1 identifying equestrians as vulnerable road users and horses as sentient decision-making vehicles (2 harmonising laws regarding passing horses, (3 mandating personal protective equipment, (4 improving road signage, (5 comprehensive data collection, (6 developing mutual understanding amongst road-users, (7 safer road design and alternative riding spaces; and (8 increasing investment in horse-related safety initiatives.

  6. 77 FR 1658 - Adjustment of the Amount for the Optional Rider for Proof of NVOCC Financial Responsibility for...

    Science.gov (United States)

    2012-01-11

    ... your overall business costs? If so, how? 2. What do you see as the advantages and disadvantages of an... believes that the optional rider method of conducting business is ``a fair and equitable'' solution to the... coverage is warranted due to the lower value of the U.S. dollar today.'' Mohawk did not identify...

  7. Inroads into Equestrian Safety: Rider-Reported Factors Contributing to Horse-Related Accidents and Near Misses on Australian Roads.

    Science.gov (United States)

    Thompson, Kirrilly; Matthews, Chelsea

    2015-07-22

    Horse riding and horse-related interactions are inherently dangerous. When they occur on public roads, the risk profile of equestrian activities is complicated by interactions with other road users. Research has identified speed, proximity, visibility, conspicuity and mutual misunderstanding as factors contributing to accidents and near misses. However, little is known about their significance or incidence in Australia. To explore road safety issues amongst Australian equestrians, we conducted an online survey. More than half of all riders (52%) reported having experienced at least one accident or near miss in the 12 months prior to the survey. Whilst our findings confirm the factors identified overseas, we also identified issues around rider misunderstanding of road rules and driver misunderstanding of rider hand signals. Of particular concern, we also found reports of potentially dangerous rider-directed road rage. We identify several areas for potential safety intervention including (1) identifying equestrians as vulnerable road users and horses as sentient decision-making vehicles (2) harmonising laws regarding passing horses, (3) mandating personal protective equipment, (4) improving road signage, (5) comprehensive data collection, (6) developing mutual understanding amongst road-users, (7) safer road design and alternative riding spaces; and (8) increasing investment in horse-related safety initiatives.

  8. Influence of riders' skill on plasma cortisol levels of horses walking on forest and field trekking courses.

    Science.gov (United States)

    Ono, Ayaka; Matsuura, Akihiro; Yamazaki, Yumi; Sakai, Wakako; Watanabe, Kentaro; Nakanowatari, Toshihiko; Kobayashi, Hiroshi; Irimajiri, Mami; Hodate, Koichi

    2017-10-01

    The aim of this study was to evaluate the influence of rider's skill on the plasma cortisol levels of trekking horses on two courses, walking on field and forest courses (about 4.5 to 5.1 km each). Three riders of different skills did horse trekking (HT) in a tandem line under a fixed order: advanced-leading, beginner-second and intermediate-last. A total of six horses were used and they experienced all positions in both courses; a total of 12 experiments were done. Blood samples were obtained before HT, immediately after and 2 h after HT. As a control, additional blood samples were obtained from the same horses on non-riding days. Irrespective of the course and the rider's skill, the cortisol level before HT was higher than that of control (P stress of trekking horse was not sufficient to disturb the circadian rhythm of the cortisol level, irrespective of the course and the rider's skill. © 2017 Japanese Society of Animal Science.

  9. Terminals for Suburb Bus Transport in Bratislava

    Science.gov (United States)

    Schlosser, Tibor; Schlosser, Peter; Cápayová, Silvia; Hodáková, Dominika

    2017-10-01

    The main objective of this article is to describe the strategy for development of the public transport terminals in the city of Bratislava, Capital of Slovak Republic. The reason goes from the private operator Slovak Lines, who operates the suburb bus transport in the agglomeration of the city. For this operator was created a transport model, while placing emphasis on optimizing the compliance of suburban public transport with urban public transport in the city of Bratislava and evaluating the significance of the new Bus Station to be constructed at Mlynské Nivy - in a new down town centre of the city. The main issue is to ensure the best available offer of public transport (PT) to passengers in the Bratislava agglomeration. The subject of the study was oriented to specify and propose changes in the transport infrastructure and integrated public transport organisation on the area of the city in terms of the significant position of the new Mlynské Nivy Bus Station (MN BS), which is under preparation with realization in the year 2017.

  10. Brazilian hybrid electric fuel cell bus

    Energy Technology Data Exchange (ETDEWEB)

    Miranda, P.E.V.; Carreira, E.S. [Coppe-Federal Univ. of Rio de Janeiro (Brazil). Hydrogen Lab.

    2010-07-01

    The first prototype of a hybrid electric fuel cell bus developed with Brazilian technology is unveiled. It is a 12 m urban-type, low-floor, air-conditioned bus that possesses three doors, air suspension, 29 seats and reversible wheelchair site. The bus body was built based on a double-deck type monoblock vehicle that is able to sustain important load on its roof. This allowed positioning of the type 3 hydrogen tanks and the low weight traction batteries on the roof of the vehicles without dynamic stabilization problems. A novel hybrid energy configuration was designed in such a way that the low-power (77 kWe) fuel cell works on steady-state operation mode, not responding directly to the traction motor load demand. The rate of kinetic energy regeneration upon breaking was optimized by the use of an electric hybrid system with predominance of batteries and also by utilizing supercapacitors. The electric-electronic devices and the security control softwares for the auxiliary and traction systems were developed in-house. The innovative hybrid-electric traction system configuration led to the possibility to decrease the fuel cell power, with positive impact on weight and system volume reduction, as well as to significantly decrease the hydrogen consumption. (orig.)

  11. Writing on the Bus: Using Athletic Team Notebooks and Journals to Advance Learning and Performance in Sports

    Science.gov (United States)

    Kent, Richard

    2012-01-01

    "Writing on the Bus" showcases the what, how, and why of using athletic team notebooks and journals. The book guides coaches and athletes, from elementary school through college, in analyzing games while thinking deeply about motivation, goal setting, and communication in order to optimize performance. Filled with lesson plans, writing activities,…

  12. Oil inventory behaviour: the public and private sector relationship and the free-rider problem

    International Nuclear Information System (INIS)

    Al-Faris, A.F.

    1992-01-01

    For oil-importing countries, the uninterrupted flow of energy sources lies at the heart of their national security. The crises of 1973-74 and 1979-80 have demonstrated the vulnerability of their economies to oil shortages, and the need to maintain a certain level of stocks to absorb unexpected losses in normal supply. On the other hand, oil producers have perceived a large inventory accumulation as a destabilizing factor to the oil market. This paper introduces fresh evidence on the dynamic nature of the relationship between OECD countries on the one hand and the public and private sectors on the other. The aims of the paper are, thus, twofold. The first is to highlight the underlying determinants of the inventory policies in major OECD countries. Of particular interest to this inquiry is the question of the free-rider phenomenon. The second is to study the interaction between public and private inventories in the framework of a dynamic model. (author)

  13. Peptic ulcer among urban bus drivers in Denmark

    DEFF Research Database (Denmark)

    Netterstrøm, Bo; Juel, K

    1990-01-01

    As part of a survey on the work environment of bus drivers, 2045 (83%) of 2465 male bus drivers in the three major cities in Denmark in 1978 answered a postal questionnaire on health and working conditions. In order to evaluate the relative occurrence of peptic ulcer among the bus drivers, a follow......-up study was also conducted. All hospital discharges with a peptic ulcer diagnosis among the bus drivers were registered from the Danish National Patient Register. All Danish men were used as reference group. On the basis of the 1978-questionnaire association between occupational and psychosocial factors...... and subsequent hospital discharge with a peptic ulcer diagnosis was studied. The prevalence of abdominal pain alleviated by food intake was 12% among bus drivers and 6% in the reference group. The incidence of hospital discharge with duodenal ulcer among younger bus drivers was twice the incidence among Danish...

  14. The magnitude of translational and rotational head accelerations experienced by riders during downhill mountain biking.

    Science.gov (United States)

    Hurst, Howard T; Atkins, Stephen; Dickinson, Ben D

    2018-03-21

    To determine the magnitude of translational and rotational head accelerations during downhill mountain biking. Observational study. Sixteen male downhill cyclists (age 26.4±8.4years; stature 179.4±7.2cm; mass 75.3±5.9kg) were monitored during two rounds of the British Downhill Series. Riders performed two runs on each course wearing a triaxial accelerometer behind the right ear. The means of the two runs for each course were used to determine differences between courses for mean and maximum peak translational (g) and rotational accelerations (rad/s 2 ) and impact duration for each course. Significant differences (p10g), FW=12.5±7.6, RYF=42.8±27.4 (t (22.96) =-4.70; p<0.001; 95% CI=17.00 to 43.64); maximum peak rotational acceleration, FW=6805.4±3073.8rad/s 2 , RYF=9799.9±3381.7rad/s 2 (t (32) =-2.636; p=0.01; 95% CI=680.31 to 5308.38); mean acceleration duration FW=4.7±1.2ms, RYF=6.5±1.4ms (t (32) =-4.05; p<0.001; 95% CI=0.91 to 2.76) and maximum acceleration duration, FW=11.6±4.5ms, RYF=21.2±9.1 (t (29.51) =-4.06; p=0.001; 95% CI=4.21 to 14.94). No other significant differences were found. Findings indicate that downhill riders may be at risk of sustaining traumatic brain injuries and course design influences the number and magnitude of accelerations. Copyright © 2018 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

  15. Aspek Hukum Perlindungan terhadap Penumpang Bus dalam Mewujudkan Perlindungan Konsumen

    OpenAIRE

    Harahap, Rabiah Z

    2016-01-01

    Bus is the one of transportation which is often used by society. Society as passenger of bus righteously gains protection. Many of accident happens in public transportation especially bus that rises a question the important of protection for people as the accicent victim. This question is worthy to be solved because many of public transportation company ignores the passenger's right. Based on this, government shall take control with presentation of new regulation that aims protection people ...

  16. Emission inventory estimation of an intercity bus terminal.

    Science.gov (United States)

    Qiu, Zhaowen; Li, Xiaoxia; Hao, Yanzhao; Deng, Shunxi; Gao, H Oliver

    2016-06-01

    Intercity bus terminals are hotspots of air pollution due to concentrated activities of diesel buses. In order to evaluate the bus terminals' impact on air quality, it is necessary to estimate the associated mobile emission inventories. Since the vehicles' operating condition at the bus terminal varies significantly, conventional calculation of the emissions based on average emission factors suffers the loss of accuracy. In this study, we examined a typical intercity bus terminal-the Southern City Bus Station of Xi'an, China-using a multi-scale emission model-(US EPA's MOVES model)-to quantity the vehicle emission inventory. A representative operating cycle for buses within the station is constructed. The emission inventory was then estimated using detailed inputs including vehicle ages, operating speeds, operating schedules, and operating mode distribution, as well as meteorological data (temperature and humidity). Five functional areas (bus yard, platforms, disembarking area, bus travel routes within the station, and bus entrance/exit routes) at the terminal were identified, and the bus operation cycle was established using the micro-trip cycle construction method. Results of our case study showed that switching to compressed natural gas (CNG) from diesel fuel could reduce PM2.5 and CO emissions by 85.64 and 6.21 %, respectively, in the microenvironment of the bus terminal. When CNG is used, tail pipe exhaust PM2.5 emission is significantly reduced, even less than brake wear PM2.5. The estimated bus operating cycles can also offer researchers and policy makers important information for emission evaluation in the planning and design of any typical intercity bus terminals of a similar scale.

  17. Design Report for Isolated RS-485 Bus Node

    Science.gov (United States)

    2016-07-01

    TERMS Android , RS-485, isolated, USB, smartphone 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18. NUMBER...controlled wired RS-485 network. The Android -based smartphone or tablet is used in conjunction with a USB to serial bridge to operate as the bus master in...the system. The Android device operates in USB Host mode and communicates to the RS-485 bus as if a single peripheral on the USB bus. 15. SUBJECT

  18. Network Analysis of Urban Traffic with Big Bus Data

    OpenAIRE

    Zhao, Kai

    2016-01-01

    Urban traffic analysis is crucial for traffic forecasting systems, urban planning and, more recently, various mobile and network applications. In this paper, we analyse urban traffic with network and statistical methods. Our analysis is based on one big bus dataset containing 45 million bus arrival samples in Helsinki. We mainly address following questions: 1. How can we identify the areas that cause most of the traffic in the city? 2. Why there is a urban traffic? Is bus traffic a key cause ...

  19. Countermeasures for Developing New Energy Bus Standards in China

    Science.gov (United States)

    Shi, Xin

    2018-01-01

    With the rapid development of new energy vehicle technology, new energy bus has become more and more popular in China, and the relevant standards and policy are urgently needed to guide the market. According to the assessment of the development situation on new energy vehicle technology and new energy bus, combing with traffic policy guidance and the development trend of new energy vehicles, this paper aims to put forward the countermeasures of the new energy bus standard in China, including standard system, key standards and relevant recommendations. Research result is expected to provide decision support for the wide application of new energy bus in China.

  20. Status of the IEEE P896 Future Backplane Bus

    International Nuclear Information System (INIS)

    Gustavson, D.B.

    1983-10-01

    The IEEE P896 Future Backplane Bus project has been influenced by and has influenced FASTBUS and several other contemporary bus designs. This paper summarizes the current status of that project, which is directed toward the needs of modern 32-bit microprocessor systems with multiple processors. Some of the technology developed for P896 will be important for future non-ECL implementations of FASTBUS and other buses. In particular, new bus drivers and receivers should greatly improve the performance and reliability of backplane buses and cable buses. The current status of the P896 serial bus is also summarized

  1. The Software Bus, an Object-Oriented Data Exchange System

    International Nuclear Information System (INIS)

    Akerbaek, T.; Louka, M.

    1996-01-01

    This document describes the Software Bus System, developed for object-oriented task to task communication in a TCP/IP based network. The Software Bus is a set of library functions, developed to be used for the Picasso-3 UIMS, and as a general purpose tool for dynamically interfacing programs at run-time. The Software Bus offers a high level object-oriented data exchange mechanism that relieves the application programmer of the low level TCP/IP-programming and communication protocol handling. The Software Bus is currently available under several UNIX platforms and a version for Windows NT is planned for late 1996. (author)

  2. Program Guide for Diesel Engine Mechanics 8742000 (IN47.060500) and Heavy Duty Truck and Bus Mechanics DIM0991 (IN47.060501).

    Science.gov (United States)

    University of South Florida, Tampa. Coll. of Education.

    This competency-based program guide provides course content information and procedures for secondary schools, postsecondary vocational schools, and community colleges in Florida that conduct programs in diesel engine mechanics and heavy duty truck and bus mechanics. The first section is on legal authority, which applies to all vocational education…

  3. Extracting potential bus lines of Customized City Bus Service based on public transport big data

    Science.gov (United States)

    Ren, Yibin; Chen, Ge; Han, Yong; Zheng, Huangcheng

    2016-11-01

    Customized City Bus Service (CCBS) can reduce the traffic congestion and environmental pollution that caused by the increasing in private cars, effectively. This study aims to extract the potential bus lines and each line's passenger density of CCBS by mining the public transport big data. The datasets used in this study are mainly Smart Card Data (SCD) and bus GPS data of Qingdao, China, from October 11th and November 7th 2015. Firstly, we compute the temporal-origin-destination (TOD) of passengers by mining SCD and bus GPS data. Compared with the traditional OD, TOD not only has the spatial location, but also contains the trip's boarding time. Secondly, based on the traditional DBSCAN algorithm, we put forwards an algorithm, named TOD-DBSCAN, combined with the spatial-temporal features of TOD.TOD-DBSCAN is used to cluster the TOD trajectories in peak hours of all working days. Then, we define two variables P and N to describe the possibility and passenger destiny of a potential CCBS line. P is the probability of the CCBS line. And N represents the potential passenger destiny of the line. Lastly, we visualize the potential CCBS lines extracted by our procedure on the map and analyse relationship between potential CCBS lines and the urban spatial structure.

  4. Bus Rapid Transit and Socioeconomic Condition of Bus Commuters in Lagos State

    Directory of Open Access Journals (Sweden)

    Owolabi L. Kuye

    2017-10-01

    Full Text Available Road transport is one of the most common means of transportation across the world. Bus transportation in Nigeria had witnessed many problems for the past decades considering the growing population with the attendant loss of lives and properties in most cities like Lagos in Nigeria. This paper focuses on the adequacy of services provided by Bus Rapid Transit (BRT in Lagos State with respect to the extent to which it influences the socioeconomic conditions of bus commuters. It examines the effect of services rendered by BRT on cost reduction potential, income and safety. Multistage sampling technique was used to select 20 samples each from all respondents in all local government area in Lagos State to reach a total of three hundred and thirty (330 samples. The data collection instrument was the questionnaire which was validated. Data collected were analysed with the use of descriptive statistics such as means, percentages and standard deviation and inferential statistics such as regression and analysis of variance techniques. Findings showed that BRT services has reduced the cost of bus commuters and also increased safety and security thereby increasing the socioeconomic condition of Lagosians. The study recommends improvements in BRT services through the deployment of technology as it had been used in developed countries.

  5. Oracle Service Bus 11g Development Cookbook

    CERN Document Server

    Schmutz, Guido; van Zoggel, Jan

    2012-01-01

    This cookbook is full of immediately useable recipes showing you how to develop service and message-oriented (integration) applications on the Oracle Service Bus. In addition to its cookbook style, which ensures the solutions are presented in a clear step-by-step manner, the explanations go into great detail, which makes it good learning material for everyone who has experience in OSB and wants to improve. Most of the recipes are designed in such a way that each recipe is presented as a separate, standalone entity and reading of prior recipes is not required. The finished solution of each reci

  6. Bus bar joints stability and protection

    CERN Document Server

    Verweij, A

    2009-01-01

    A defective bus connection between two dipole magnets was the primary cause of the incident in sector 34 on September 19th. I will show how this could have happened, i.e. how a highly resistive joint has caused a thermal runaway and burned (or opened) before the QPS threshold was reached. In the second part of the talk I will present the new detection limits for the QPS upgrade of the RB and RQ circuits, required to avoid similar thermal runaways in the future.

  7. Redesign of Transjakarta Bus Driver's Cabin

    Science.gov (United States)

    Mardi Safitri, Dian; Azmi, Nora; Singh, Gurbinder; Astuti, Pudji

    2016-02-01

    Ergonomic risk at work stations with type Seated Work Control was one of the problems faced by Transjakarta bus driver. Currently “Trisakti” type bus, one type of bus that is used by Transjakarta in corridor 9, serving route Pinang Ranti - Pluit, gained many complaints from drivers. From the results of Nordic Body Map questionnaires given to 30 drivers, it was known that drivers feel pain in the neck, arms, hips, and buttocks. Allegedly this was due to the seat position and the button/panel bus has a considerable distance range (1 meter) to be achieved by drivers. In addition, preliminary results of the questionnaire using Workstation Checklist identified their complaints about uncomfortable cushion, driver's seat backrest, and the exact position of the AC is above the driver head. To reduce the risk level of ergonomics, then did research to design the cabin by using a generic approach to designing products. The risk analysis driver posture before the design was done by using Rapid Upper Limb Assessment (RULA), Rapid Entire Body Assessment (REBA), and Quick Exposure Checklist (QEC), while the calculation of the moment the body is done by using software Mannequin Pro V10.2. Furthermore, the design of generic products was done through the stages: need metric-matrix, house of quality, anthropometric data collection, classification tree concept, concept screening, scoring concept, design and manufacture of products in the form of two-dimensional. While the design after design risk analysis driver posture was done by using RULA, REBA, and calculation of moments body as well as the design visualized using software 3DMax. From the results of analysis before the draft design improvements cabin RULA obtained scores of 6, REBA 9, and the result amounted to 57.38% QEC and moment forces on the back is 247.3 LbF.inch and on the right hip is 72.9 LbF.in. While the results of the proposed improvements cabin design RULA obtained scores of 3, REBA 4, and the moment of force on

  8. A Conceptual Approach for Optimising Bus Stop Spacing

    Science.gov (United States)

    Johar, Amita; Jain, S. S.; Garg, P. k.

    2017-06-01

    An efficient public transportation system is essential of any country. The growth, development and shape of the urban areas are mainly due to availability of good transportation (Shah et al. in Inst Town Plan India J 5(3):50-59, 1). In developing countries, like India, travel by local bus in a city is very common. The accidents, congestion, pollution and appropriate location of bus stops are the major problems arising in metropolitan cities. Among all the metropolitan cities in India, Delhi has highest percentage of growth of population and vehicles. Therefore, it is important to adopt efficient and effective ways to improve mobility in different metropolitan cities in order to overcome the problem and to reduce the number of private vehicles on the road. The primary objective of this paper is to present a methodology for developing a model for optimum bus stop spacing (OBSS). It describes the evaluation of existing urban bus route, data collection, development of model for optimizing urban bus route and application of model. In this work, the bus passenger generalized cost method is used to optimize the spacing between bus stops. For the development of model, a computer program is required to be written. The applicability of the model has been evaluated by taking the data of urban bus route of Delhi Transport Corporation (DTC) in Excel sheet in first phase. Later on, it is proposed to develop a programming in C++ language. The developed model is expected to be useful to transport planner for rational design of the spacing of bus stops to save travel time and to generalize operating cost. After analysis it is found that spacing between the bus stop comes out to be between 250 and 500 m. The Proposed Spacing of bus stops is done considering the points that they don't come nearer to metro/rail station, entry or exit of flyover and near traffic signal.

  9. Adopting Clean Fuels and Technologies on School Buses. Pollution and Health Impacts in Children.

    Science.gov (United States)

    Adar, Sara D; D'Souza, Jennifer; Sheppard, Lianne; Kaufman, Joel D; Hallstrand, Teal S; Davey, Mark E; Sullivan, James R; Jahnke, Jordan; Koenig, Jane; Larson, Timothy V; Liu, L J Sally

    2015-06-15

    More than 25 million American children breathe polluted air on diesel school buses. Emission reduction policies exist, but the health impacts to individual children have not been evaluated. Using a natural experiment, we characterized the exposures and health of 275 school bus riders before, during, and after the adoption of clean technologies and fuels between 2005 and 2009. Air pollution was measured during 597 trips on 188 school buses. Repeated measures of exhaled nitric oxide (FeNO), lung function (FEV1, FVC), and absenteeism were also collected monthly (1,768 visits). Mixed-effects models longitudinally related the adoption of diesel oxidation catalysts (DOCs), closed crankcase ventilation systems (CCVs), ultralow-sulfur diesel (ULSD), or biodiesel with exposures and health. Fine and ultrafine particle concentrations were 10-50% lower on buses using ULSD, DOCs, and/or CCVs. ULSD adoption was also associated with reduced FeNO (-16% [95% confidence interval (CI), -21 to -10%]), greater changes in FVC and FEV1 (0.02 [95% CI, 0.003 to 0.05] and 0.01 [95% CI, -0.006 to 0.03] L/yr, respectively), and lower absenteeism (-8% [95% CI, -16.0 to -0.7%]), with stronger associations among patients with asthma. DOCs, and to a lesser extent CCVs, also were associated with improved FeNO, FVC growth, and absenteeism, but these findings were primarily restricted to patients with persistent asthma and were often sensitive to control for ULSD. No health benefits were noted for biodiesel. Extrapolating to the U.S. population, changed fuel/technologies likely reduced absenteeism by more than 14 million/yr. National and local diesel policies appear to have reduced children's exposures and improved health.

  10. Adopting Clean Fuels and Technologies on School Buses. Pollution and Health Impacts in Children

    Science.gov (United States)

    D’Souza, Jennifer; Sheppard, Lianne; Kaufman, Joel D.; Hallstrand, Teal S.; Davey, Mark E.; Sullivan, James R.; Jahnke, Jordan; Koenig, Jane; Larson, Timothy V.; Liu, L. J. Sally

    2015-01-01

    Rationale: More than 25 million American children breathe polluted air on diesel school buses. Emission reduction policies exist, but the health impacts to individual children have not been evaluated. Methods: Using a natural experiment, we characterized the exposures and health of 275 school bus riders before, during, and after the adoption of clean technologies and fuels between 2005 and 2009. Air pollution was measured during 597 trips on 188 school buses. Repeated measures of exhaled nitric oxide (FeNO), lung function (FEV1, FVC), and absenteeism were also collected monthly (1,768 visits). Mixed-effects models longitudinally related the adoption of diesel oxidation catalysts (DOCs), closed crankcase ventilation systems (CCVs), ultralow-sulfur diesel (ULSD), or biodiesel with exposures and health. Measurements and Main Results: Fine and ultrafine particle concentrations were 10–50% lower on buses using ULSD, DOCs, and/or CCVs. ULSD adoption was also associated with reduced FeNO (−16% [95% confidence interval (CI), −21 to −10%]), greater changes in FVC and FEV1 (0.02 [95% CI, 0.003 to 0.05] and 0.01 [95% CI, −0.006 to 0.03] L/yr, respectively), and lower absenteeism (−8% [95% CI, −16.0 to −0.7%]), with stronger associations among patients with asthma. DOCs, and to a lesser extent CCVs, also were associated with improved FeNO, FVC growth, and absenteeism, but these findings were primarily restricted to patients with persistent asthma and were often sensitive to control for ULSD. No health benefits were noted for biodiesel. Extrapolating to the U.S. population, changed fuel/technologies likely reduced absenteeism by more than 14 million/yr. Conclusions: National and local diesel policies appear to have reduced children’s exposures and improved health. PMID:25867003

  11. Schedule and complex motion of shuttle bus induced by periodic inflow of passengers

    Science.gov (United States)

    Nagatani, Takashi; Naito, Yuichi

    2011-09-01

    We have studied the dynamic behavior of a bus in the shuttle bus transportation with a periodic inflow. A bus schedule is closely related to the dynamics. We present the modified circle map model for the dynamics of the shuttle bus. The motion of the shuttle bus depends on the loading parameter and the inflow period. The shuttle bus displays the periodic, quasi-periodic, and chaotic motions with varying both loading parameter and inflow rate.

  12. Connecticut nutmeg fuel cell bus project : first analysis report.

    Science.gov (United States)

    2012-07-01

    This report summarizes the experience and early results from a fuel cell bus demonstration funded by the Federal Transit Administra-tion (FTA) under the National Fuel Cell Bus Program (NFCBP). A team led by the Northeast Advanced Vehicle Consortium a...

  13. Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus: Preliminary Evaluation Results

    Energy Technology Data Exchange (ETDEWEB)

    Chandler, K.; Eudy, L.

    2008-10-01

    This report provides preliminary results from a National Renewable Energy Laboratory evaluation of a protoptye fuel cell transit bus operating at Connecticut Transit in Hartford. Included are descriptions of the planned fuel cell bus demonstration and equipment; early results and agency experience are also provided.

  14. 3D reconstructions of a controlled bus bombing

    DEFF Research Database (Denmark)

    Villa, Chiara; Hansen, Nikolaj Friis; Hansen, Kamilla Maria

    2018-01-01

    Objectives: to demonstrate the usefulness of 3D reconstructions to better understand the dynamic of a controlled bus bombing. Materials and methods: 3D models of the victims (pigs) were created from post-mortem CT scanning using Mimic software; 3D models of the crime scene (bus) were generated by...

  15. Review of bus drivers' occupational stress and stress prevention

    NARCIS (Netherlands)

    Kompier, M.A.J.; Di Martino, V.

    1995-01-01

    Although heterogeneous in methodology and content, 32 studies from 13 countries on bus drivers' work and health are similar in their conclusions. Bus-driving–characterized by high demands, low control and low support – can be regarded as a classic example of high-strain occupation, with high risks

  16. 32 CFR 935.138 - Motor bus operation.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false Motor bus operation. 935.138 Section 935.138 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE TERRITORIAL AND INSULAR REGULATIONS WAKE ISLAND CODE Motor Vehicle Code § 935.138 Motor bus operation. Each person operating a motor...

  17. Bus Lifecycle Cost Model for Federal Land Management Agencies.

    Science.gov (United States)

    2011-09-30

    The Bus Lifecycle Cost Model is a spreadsheet-based planning tool that estimates capital, operating, and maintenance costs for various bus types over the full lifecycle of the vehicle. The model is based on a number of operating characteristics, incl...

  18. Magnetic resonance imaging findings of the lumbar spine in elite horseback riders: correlations with back pain, body mass index, trunk/leg-length coefficient, and riding discipline.

    Science.gov (United States)

    Kraft, Clayton N; Pennekamp, Peter H; Becker, Ute; Young, Mei; Diedrich, Oliver; Lüring, Christian; von Falkenhausen, Makus

    2009-11-01

    Most orthopaedic problems experienced by competitive horseback riders are related to pain in the lower back, hip joint, and hamstring muscles. Riders-especially, show jumpers-are frequently hampered in their performance because of lumbar pain. To date, there has been no research into lumbar disk degeneration in elite competitive riders. Competitive horseback riding accelerates lumbar disk degeneration. Cross-sectional study; Level of evidence, 3. Fifty-eight elite riders (18 men, 40 women; mean age, 32.4 years) and a control group of 30 nonriding volunteers (17 men, 13 women; mean age, 28.7 years) were evaluated for lumbar disk degeneration, cross-sectional area of paraspinal muscles, spondylolysis, and spondylolisthesis, using magnetic resonance imaging (MRI). The prevalence of disk degeneration between the 2 groups was compared, and the relationship was investigated between low back pain (LBP), riding discipline, body mass index (BMI), trunk/leg-length coefficient, and MRI results. Eighty-eight percent of elite riders (n = 51) had a history of LBP, versus 33% of the controls (P back pain. Although riders have a high prevalence of LBP, there is no conclusive MRI evidence to suggest that the cause lies in undue disk degeneration, spondylolysis, spondylolisthesis, or pathologic changes of the paraspinal muscles of the lumbar spine.

  19. Sustainable transport and the organisation of bus services in Manchester

    DEFF Research Database (Denmark)

    Gudmundsson, Henrik; Sørensen, Claus Hedegaard

    2008-01-01

    alternative modes of transport to private cars, such as public transport. In this paper we focus only on the potential of bus transport services in cities for attracting travellers from cars. It is a basic assumption behind this paper that the ability of public bus transport to attract travellers from cars...... depends on how the bus sector is organised. By organisation we adopt an institutional point of view and consider basic modes of governance. Basic modes of governance include the forms “market”, “hierarchy” and “network” (Powell 1990). So-called New Public Management (NPM) reforms have changed the modes...... of governance of bus transport in several countries, including Denmark and the United Kingdom. Our focus is on how New Public Mangement Reforms have changed the mix of governance modes and thus may have influenced the ability of urban bus transport to attract travellers from cars. We focus on a particular case...

  20. SISTEM RESERVASI TIKET BUS DI TERMINAL ARJOSARI MALANG

    Directory of Open Access Journals (Sweden)

    Surya Wirawan

    2013-10-01

    Full Text Available Bus Ticket Reservation System is an application that can be used to help booking bus tickets and the buyer will get a report via SMS Gateway. The reservation system is made by conducting field studies in Arjosari Bus Station Malang. This system uses SMS Gateway to send the report to the buyer after booking bus tickets online. SMS Gateway on this application serves as a liaison which delays sms between External Short Message entitiy (ESME and Short Message Service Center (SMSC and so does in reserve.The reservation system made is developed with the PHP programming language and has a prototype system pattern. System functions were tested using the validation testing, performance testing, and usability testing. The results percentage of responses usability testing is 67.7%. This shows that Ticket Reservation System at Arjosari Bus Station can be used well enough.

  1. Research on the Coordinated Design of Bus and Taxi Station

    Directory of Open Access Journals (Sweden)

    Jiangfeng Xi

    2015-01-01

    Full Text Available Rises in the number of transit buses, bus routes, and overall traffic volume in China’s cities, coupled with interference from other transport modes, such as taxis loading and unloading passengers nearby, have led to increasing traffic delays at bus stops, which is considered one of the factors degrading service levels and traffic operations on urban roadways. This paper studies traffic characteristics at bus stops, investigates variations in delay from different types or designs of bus stops, and analyzes the impact of it on traffic capacity, the purpose of which is to propose a solution to predicting the feasibility of an integrated design of bus stops and taxi stands with the help of mathematical models and based on the objectives of optimal traffic operations and passenger transfer.

  2. Improved design of HIRFL-CSR EVME bus controller

    International Nuclear Information System (INIS)

    Zhao Long; Liu Wufeng; Qiao Weimin; Jing Lan

    2009-01-01

    The EVME bus controller which is a key component of the HIRFL-CSR control system was improved. Besides reconfiguring the embedded Linux, a utility program was developed for data exchange between the controller and the database. The bus controller is based on ARM920T(ARM9) micro processor which is BGA packaged. The bus controller has the universal interface of VGA display, keyboard, and mouse. The backboard interface logic is programmed in an in-system configurable FPGA device. The bus can drive high current up to 64 mA, with the flexibility of the programmable signal definitions. All the improved performance helped the EVME bus controller play a crucial role in HIRFL-CSR control system. (authors)

  3. Results of the ANSWER Trial Using the PulseRider for the Treatment of Broad-Necked, Bifurcation Aneurysms.

    Science.gov (United States)

    Spiotta, Alejandro M; Derdeyn, Colin P; Tateshima, Satoshi; Mocco, Jay; Crowley, R Webster; Liu, Kenneth C; Jensen, Lee; Ebersole, Koji; Reeves, Alan; Lopes, Demetrius K; Hanel, Ricardo A; Sauvageau, Eric; Duckwiler, Gary; Siddiqui, Adnan; Levy, Elad; Puri, Ajit; Pride, Lee; Novakovic, Roberta; Chaudry, M Imran; Turner, Raymond D; Turk, Aquilla S

    2017-07-01

    The safety and probable benefit of the PulseRider (Pulsar Vascular, Los Gatos, California) for the treatment of broad-necked, bifurcation aneurysms was studied in the context of the prospective, nonrandomized, single arm clinical trial-the Adjunctive Neurovascular Support of Wide-neck aneurysm Embolization and Reconstruction (ANSWER) Trial. To present the results of the United States cases employing the PulseRider device as part of the ANSWER clinical trial. Aneurysms treated with the PulseRider device among sites enrolling in the ANSWER trial were prospectively studied and the results are summarized. Aneurysms arising at either the carotid terminus or basilar apex that were relatively broad necked were considered candidates for inclusion into the ANSWER study. Thirty-four patients were enrolled (29 female and 5 male) with a mean age of 60.9 years (27 basilar apex and 7 carotid terminus). Mean aneurysm height ranged from 2.4 to 15.9 mm with a mean neck size of 5.2 mm (range 2.3-11.6 mm). In all patients, the device was delivered and deployed. Immediate Raymond I or II occlusion was achieved in 82.4% and progressed to 87.9% at 6-month follow-up. A modified Rankin Score of 2 or less was seen in 94% of patients at 6 months. The results from the ANSWER trial demonstrate that the PulseRider device is safe and offers probable benefit as for the treatment of bifurcation aneurysms arising at the basilar apex or carotid terminus. As such, it represents a useful addition to the armamentarium of the neuroendovascular specialist. Copyright © 2017 by the Congress of Neurological Surgeons

  4. The scourge of head injury among commercial motorcycle riders in Kampala; a preventable clinical and public health menace.

    Science.gov (United States)

    Kamulegeya, Louis H; Kizito, Mark; Nassali, Rosemary; Bagayana, Shiela; Elobu, Alex E

    2015-09-01

    Trauma is an increasingly important cause of disease globally. Half of this trauma is from road traffic injuries with motorcycles contributing 21-58%. Low protective gear use, lack of regulation and weak traffic law enforcement contribute to unsafe nature of commercial motorcycles also known as "boda boda" in Uganda. To determine the prevalence of protective gear use, the occurrence of head injury and the relationship between the two among commercial motorcycle riders in Kampala. Following ethical approval we recruited consecutive consenting participants to this analytical cross-sectional study. Data was collected using pretested interviewer administered questionnaires, double entered in Epidata and analyzed with STATA. Proportions and means were used to summarize data. Odds ratios were calculated for association between wearing helmets and occurrence and severity of head injury. All 328 participants recruited were male. Of these, 18.6% used Protective gear and 71.1 % sustained head injury. Helmets protected users from head injury (OR 0.43, 95% CI, 0.23-0.8) and significantly reduced its severity when it occurred. Protective gear use was low, with high occurrence of head injury among commercial motorcycle riders in Uganda. More effective strategies are needed to promote protective gear use among Uganda's commercial motorcycle riders.

  5. Transit Rider Body Mass Index Before and After Completion of Street Light-Rail Line in Utah.

    Science.gov (United States)

    Brown, Barbara B; Smith, Ken R; Jensen, Wyatt A; Tharp, Doug

    2017-09-01

    To determine whether 2012 to 2015 (times 1-3) ridership changes correlated with body mass index (BMI) changes after transit line completion in Salt Lake City, Utah. We used Global Positioning System/accelerometry-measured transit ridership measures in 2012 to 2013 (times 1-2) to compare objective and self-reported ridership. Regression models related changes in objectively measured ridership (times 1-2) and self-reported ridership (times 1-2 and times 1-3) to BMI changes, adjusting for control variables. Objective and self-reported ridership measures were consistent. From time 1 to 2 (P = .021) or to 3 (P = .015), BMI increased among self-reported former riders and decreased among new riders (P = .09 for both times 1-2 and times 1-3), although the latter was nonsignificant. Time 3 attrition adjustment had no effect on results. Adjusting for baseline BMI, the nonsignificant effect for new riders remained nonsignificant, indicating no BMI change; the BMI increase after discontinuing transit remained significant. Observed BMI increases subsequent to stopping transit ridership persisted for more than 2 years (postintervention). These results suggest that transit ridership protects against BMI gains and support the need to provide convenient transit for public health.

  6. Plasticity effect of rider-horse interaction on genetic evaluations for Show Jumping discipline in sport horses.

    Science.gov (United States)

    Bartolomé, E; Menéndez-Buxadera, A; Molina, A; Valera, M

    2018-04-01

    To obtain a sport horse that excels in the highest levels of competition, breeders must take into account certain genetic and environmental factors that could influence the sport horse's performance, such as the rider-horse interaction (RHI). The main aim of this study was to describe this interaction in a genetic model by modelling it in relation to the horse's age. A total of 31,129 sport results from Spanish Sport Horses were used from a total of 1,101 animals evaluated, and these were grouped in three age levels and had been ridden by 606 different riders. Only riders who had ridden more than one horse (and vice-versa) were considered for the analyses. Five linear models with different random effects were analysed according to the covariates, the homogeneity/heterogeneity of the RHI and the relevant residual random effects. The model of best fit was then selected for the genetic evaluation of the animal. In general, models including the RHI effect (M2, M4 and M5) fitted better than the other models, and the best fit was obtained for M4 (with heterogeneous residual variance). The genetic variance increased constantly with age, whereas heritability showed a response on three intervals. This study revealed the varied evolution of the RHI with age, showing the different "plastic abilities" of this relationship. © 2018 Blackwell Verlag GmbH.

  7. Cooperative VET in Training Networks: Analysing the Free-Rider Problem in a Sociology-of-Conventions Perspective

    Directory of Open Access Journals (Sweden)

    Regula Julia Leemann

    2015-12-01

    Full Text Available In training networks, particularly small and medium-sized enterprises pool their resources to train apprentices within the framework of the dual VET system, while an intermediary organisation is tasked with managing operations. Over the course of their apprenticeship, the apprentices switch from one training company to another on a (half- yearly basis. Drawing on a case study of four training networks in Switzerland and the theoretical framework of the sociology of conventions, this paper aims to understand the reasons for the slow dissemination and reluctant adoption of this promising form of organising VET in Switzerland. The results of the study show that the system of moving from one company to another creages a variety of free-rider constellations in the distribution of the collectively generated corporative benefits. This explains why companies are reluctant to participate in this model. For the network to be sustainable, the intermediary organisation has to address discontent arising from free-rider problems while taking into account that the solutions found are always tentative and will often result in new free-rider problems.

  8. Work fatigue in urban bus drivers

    Directory of Open Access Journals (Sweden)

    Teresa Makowiec-Dąbrowska

    2015-10-01

    Full Text Available Background: Bus drivers are a special group of professional drivers who are at a very high risk of fatigue. The aim of the study was to examine whether the driver’s subjective assessment of fatigue allows for the determination of its level and identification of its causes. Material and Methods: The study group comprised 45 randomly selected bus drivers (mean age – 43.7±7.9 years, period of employment as drivers – 14.7±8.6 years. Examinations were performed in all subjects four times – before and after work on the “easy” route (outside the city center, small traffic intensity and before and after work on the “difficult” route (city center, heavy traffic. The fatigue test questionnaire, based on the list of symptoms of fatigue prepared by the Japan Research Committee of Fatigue, was used in the study. Results: The rating of fatigue after the work was significantly higher than that before the work. The profile of fatigue after work was not influenced by the type of route, but the assessment of most symptoms of fatigue reached a higher level after the “difficult” routes and the differences were statistically significant for 7 symptoms. Only the ratings of leg fatigue, feeling of heaviness, and the necessity to squint eyes and gaze with effort reached the higher levels after driving the “easy” routes. It has been found that the level of fatigue was significantly correlated with the job characteristics (driving time, the length of the route, number of stops, etc. and with the abundance of food ingested and type of beverage (coffee vs. others drunk prior to driving. Conclusions: The questionnaire used in our study to assess the subjective feeling of fatigue has proved to be a sensitive and useful tool for indicating the level and causes of fatigue. The relationship between the symptoms of fatigue and the characteristics of job and lifestyle shows that actions must be taken by both the employers and employees to prevent fatigue

  9. Green marketing, renewables, and free riders: increasing customer demand for a public good

    Energy Technology Data Exchange (ETDEWEB)

    Wiser, R.; Pickle, S.

    1997-09-01

    Retail electricity competition will allow customers to select their own power suppliers and some customers will make purchase decisions based, in part, on their concern for the environment. Green power marketing targets these customers under the assumption that they will pay a premium for ``green`` energy products such as renewable power generation. But renewable energy is not a traditional product because it supplies public goods; for example, a customer supporting renewable energy is unable to capture the environmental benefits that their investment provides to non-participating customers. As with all public goods, there is a risk that few customers will purchase ``green`` power and that many will instead ``free ride`` on others` participation. By free riding, an individual is able to enjoy the benefits of the public good while avoiding payment. This report reviews current green power marketing activities in the electric industry, introduces the extensive academic literature on public goods, free riders, and collective action problems, and explores in detail the implications of this literature for the green marketing of renewable energy. Specifically, the authors highlight the implications of the public goods literature for green power product design and marketing communications strategies. They emphasize four mechanisms that marketers can use to increase customer demand for renewable energy. Though the public goods literature can also contribute insights into the potential rationale for renewable energy policies, they leave most of these implications for future work (see Appendix A for a possible research agenda).

  10. A study of riders' noise exposure on Bay Area Rapid Transit trains.

    Science.gov (United States)

    Dinno, Alexis; Powell, Cynthia; King, Margaret Mary

    2011-02-01

    Excessive noise exposure may present a hazard to hearing, cardiovascular, and psychosomatic health. Mass transit systems, such as the Bay Area Rapid Transit (BART) system, are potential sources of excessive noise. The purpose of this study was to characterize transit noise and riders' exposure to noise on the BART system using three dosimetry metrics. We made 268 dosimetry measurements on a convenience sample of 51 line segments. Dosimetry measures were modeled using linear and nonlinear multiple regression as functions of average velocity, tunnel enclosure, flooring, and wet weather conditions and presented visually on a map of the BART system. This study provides evidence of levels of hazardous levels of noise exposure in all three dosimetry metrics. L(eq) and L(max) measures indicate exposures well above ranges associated with increased cardiovascular and psychosomatic health risks in the published literature. L(peak) indicate acute exposures hazardous to adult hearing on about 1% of line segment rides and acute exposures hazardous to child hearing on about 2% of such rides. The noise to which passengers are exposed may be due to train-specific conditions (velocity and flooring), but also to rail conditions (velocity and tunnels). These findings may point at possible remediation (revised speed limits on longer segments and those segments enclosed by tunnels). The findings also suggest that specific rail segments could be improved for noise.

  11. Motocross biking for competition and for recreation: a prospective analysis of 423 injured riders.

    Science.gov (United States)

    Singh, Rohit; Theobald, Peter; Hamad, A K; Hay, Stuart

    2015-01-01

    Motocross is a form of motorcycle racing held on established off-road circuits and has been a recreational and competitive sport across the world for over 100 years. In the UK alone, motocross has grown into a phenomenally ambitious and popular franchise. There are over 200 motocross clubs across the country, permitting over 900 events annually. Data were collected prospectively over 4 years (from 2010 to 2014) at our unit. All injuries caused by motocross biking that were referred to our trauma and orthopaedic department were included in this study, regardless of whether the rider was performing the sport competitively or recreationally. During the period studied (4 years), 423 patients were included with a total of 485 injuries, ranging from 1 to 6 injuries per patient. The patient's age range was from 4 to 73 years, with most of the injuries being sustained within the early spring and summer months representing the start of the motocross season. We present the first epidemiological study of motocross injuries in the UK. Within the growing culture of 'adrenaline sports', motocross has become an exhilarating and extremely fashionable pastime. This study has identified and categorised the spectrum of injuries from upper limb fracture dislocations to life-threatening head and chest injuries, some of which are serious and may cause significant morbidity and possible mortality. These injuries could have significant resource implications, especially for smaller rural hospitals.

  12. Assessing Bus Performance Rating in Kajang, Selangor

    Science.gov (United States)

    Norhisham, S.; Ismail, A.; Sidek, L. M.; Borhan, M. N.; Zaini, N.; Yen, A. T. G.

    2018-04-01

    The Transit Capacity and Quality of Service Manual (TCQSM) was chosen based on the review with four manuals and guidelines for the method will be applied. Six (6) attributes, namely Hours of Service, Passenger Load, Transit Auto Travel Time, Service Frequency, Punctuality Performance and Service Coverage were chosen for evaluation.[6][7][8]. A total of three (3) operators with seven (7) routes were identified in Kajang. Based on the final results, the Quality of Service (QOS) findings was rated as D, which was regarded as minimum or satisfactory. Most stakeholders’ recommendations were: for the operators to provide information on bus scheduling and have accurate information for the passengers. It was suggested that in future this study can be extended to all routes and could be repeated after the opening of the Mass Rapid Transit (MRT) stations in Kajang, so as to provide a comparison and better evaluation of the public buses in Kajang.

  13. Bus bar electrical feedthrough for electrorefiner system

    Science.gov (United States)

    Williamson, Mark; Wiedmeyer, Stanley G; Willit, James L; Barnes, Laurel A; Blaskovitz, Robert J

    2013-12-03

    A bus bar electrical feedthrough for an electrorefiner system may include a retaining plate, electrical isolator, and/or contact block. The retaining plate may include a central opening. The electrical isolator may include a top portion, a base portion, and a slot extending through the top and base portions. The top portion of the electrical isolator may be configured to extend through the central opening of the retaining plate. The contact block may include an upper section, a lower section, and a ridge separating the upper and lower sections. The upper section of the contact block may be configured to extend through the slot of the electrical isolator and the central opening of the retaining plate. Accordingly, relatively high electrical currents may be transferred into a glovebox or hot-cell facility at a relatively low cost and higher amperage capacity without sacrificing atmosphere integrity.

  14. Field bus technology in accelerator control systems

    International Nuclear Information System (INIS)

    Tang Shuming

    1999-01-01

    Since eighties to now, the computer technology, network communication and ULSI technology have been developing rapidly. The level of control for industries and scientific experiments has been upgraded accordingly, so as to meet the increasing requirements for automation. The control systems become more complicated; the devices in control systems become more and more intelligent. However the cost of DCS (Distributed Control System) is quite expensive and the period of system integration is very long. More than ten measurement results for two methods defined in the world, in order to get inter operability of intelligent devices and reduce the costs. The author presents the development trend of fieldbuses briefly and describes the main performances of CAN, LONWORKS, WOLDFIP and PROFIBUS which are mainly used in the world today. The author proposes that the field bus technology will be introduced into the accelerator control systems in the country

  15. Status of the FASTBUS standard data bus

    International Nuclear Information System (INIS)

    Larsen, R.S.

    1980-11-01

    FASTBUS is a new laboratory standard data bus intended for use in experimental data acquisition and control. The development of FASTBUS began with a feasibility study in 1976, and is presently at the development prototyping stage. The principal aims of the standard are to provide a factor of ten or more improvement in speed of data transfers over present systems, as well as to provide an architecture for systems containing multiple processors. Developmental prototypes now in progress include crates, backplanes, cooling devices, power supplies, test and diagnostic modules, and user modules. A sizeable software development effort is also underway. Several experiments have made commitments to use FASTBUS. A review of current work and potential applications is given. 10 figures

  16. Project survey for trolley-bus transport; Johdinautoliikenteen hankeselvitys

    Energy Technology Data Exchange (ETDEWEB)

    Anttila, T.; Eklund, P.; Airaksinen, S.; Maettoe, R.; Laehdetie, A.

    2011-04-15

    To investigate the feasibility and rationality of the revival of trolley bus traffic in Helsinki a full size project plan was conducted for a variety of alternatives. This included a survey on the latest developments of the trolley bus technology, three optional plans for route network, a budgetary level design for a fully functional depot in Koskela bus depot, examination of urban landscape structures, a study on organisational options, particular technical specifications applicable on suitable trolley buses and an examination of the impacts on the environment and on the future development of public transport. The basic concept of a trolley bus as a means of electric public transport vehicle has found its form over the years, but all the components of the system undergo at present intensive development. In context of this survey also the option of a fully autonomous electric bus powered by accumulators or fuel cells and the like was investigated. However, such technology is still totally inadequate for a heavy duty bus. There are no economically competitive and effective systems available as yet. The trolley bu is the far most reliable system and gives the best life cycle economy for a foreseeable future. Earliest estimates for alternative electric technologies in regular bus service are viable just after one investment cycle some time beyond 2030. Then it should be possible to run without the support of a comprehensive overhead line. The latest achievements in the development of trolley bus are auxiliary engine and accumulator systems allowing for more autonomous propulsion. Nowadays, trolley buses are equipped with an auxiliary power unit that alleviates the traditional restrictions of the overhead line. The modern trolley bus may run short distances without the trolley lines. Recuperation of the kinetic energy at deceleration (braking) either into the overhead line network or by storing it in the vehicle is one of the characteristics of modern trolley buses

  17. Task Analysis Assessment on Intrastate Bus Traffic Controllers

    Science.gov (United States)

    Yen Bin, Teo; Azlis-Sani, Jalil; Nur Annuar Mohd Yunos, Muhammad; Ismail, S. M. Sabri S. M.; Tajedi, Noor Aqilah Ahmad

    2016-11-01

    Public transportation acts as social mobility and caters the daily needs of the society for passengers to travel from one place to another. This is true for a country like Malaysia where international trade has been growing significantly over the past few decades. Task analysis assessment was conducted with the consideration of cognitive ergonomic view towards problem related to human factors. Conducting research regarding the task analysis on bus traffic controllers had allowed a better understanding regarding the nature of work and the overall monitoring activities of the bus services. This paper served to study the task analysis assessment on intrastate bus traffic controllers and the objectives of this study include to conduct task analysis assessment on the bus traffic controllers. Task analysis assessment for the bus traffic controllers was developed via Hierarchical Task Analysis (HTA). There are a total of five subsidiary tasks on level one and only two were able to be further broken down in level two. Development of HTA allowed a better understanding regarding the work and this could further ease the evaluation of the tasks conducted by the bus traffic controllers. Thus, human error could be reduced for the safety of all passengers and increase the overall efficiency of the system. Besides, it could assist in improving the operation of the bus traffic controllers by modelling or synthesizing the existing tasks if necessary.

  18. Swisstrolley 3 - An articulated trolley bus; SWISSTROLLEY 3. Gelenktrolleybus

    Energy Technology Data Exchange (ETDEWEB)

    Gisler, H.-J.

    2006-07-01

    This illustrated final report for the Swiss Federal Office of Energy (SFOE) takes a look at the Swisstrolley 3 low-floor, articulated trolley bus developed in Switzerland by the Hess AG company. Various features of the variants of the trolley bus, including single vehicle, single and double-articulated buses and bus trailers, are discussed. The reductions achieved in energy consumption, weight and noise are discussed. Typical values for power consumption are presented in graphical form. Economic viability and passenger-friendliness are examined, as are possibilities for further improvement.

  19. DWPF Melter No.2 Prototype Bus Bar Test Report

    International Nuclear Information System (INIS)

    Gordon, J.

    2003-01-01

    Characterization and performance testing of a prototype DWPF Melter No.2 Dome Heater Bus Bar are described. The prototype bus bar was designed to address the design features of the existing system which may have contributed to water leaks on Melter No.1. Performance testing of the prototype revealed significant improvement over the existing design in reduction of both bus bar and heater connection maximum temperature, while characterization revealed a few minor design and manufacturing flaws in the bar. The prototype is recommended as an improvement over the existing design. Recommendations are also made in the area of quality control to ensure that critical design requirements are met

  20. Using microcomputers for lighting appliance control using a DALI bus

    Directory of Open Access Journals (Sweden)

    Sysala Tomas

    2016-01-01

    Full Text Available Article concerns the DALI bus theoretical and practical aspects. The DALI bus is a modern technology developed especially for illumination systems control. Authors are outlining communication basic principles related to the physical layer and going up to more complex data transactions among particular devices. The article main topic is aimed at two device models development based on microcontroller and exploiting that technology. The first of those two devices is a DALI slave unit enabling the light source or multi switch with light indication components control via DALI bus. The second device measures the ambient illumination intensity and it also detects errors in the load.

  1. Optimization Model for Headway of a Suburban Bus Route

    Directory of Open Access Journals (Sweden)

    Xiaohong Jiang

    2014-01-01

    Full Text Available Due to relatively low passenger demand, headways of suburban bus route are usually longer than those of urban bus route. Actually it is also difficult to balance the benefits between passengers and operators, subject to the service standards from the government. Hence the headway of a suburban bus route is usually determined on the empirical experience of transport planners. To cope with this problem, this paper proposes an optimization model for designing the headways of suburban bus routes by minimizing the operating and user costs. The user costs take into account both the waiting time cost and the crowding cost. The feasibility and validity of the proposed model are shown by applying it to the Route 206 in Jiangning district, Nanjing city of China. Weightages of passengers’ cost and operating cost are further discussed, considering different passenger flows. It is found that the headway and objective function are affected by the weightages largely.

  2. Global Optimization for Bus Line Timetable Setting Problem

    Directory of Open Access Journals (Sweden)

    Qun Chen

    2014-01-01

    Full Text Available This paper defines bus timetables setting problem during each time period divided in terms of passenger flow intensity; it is supposed that passengers evenly arrive and bus runs are set evenly; the problem is to determine bus runs assignment in each time period to minimize the total waiting time of passengers on platforms if the number of the total runs is known. For such a multistage decision problem, this paper designed a dynamic programming algorithm to solve it. Global optimization procedures using dynamic programming are developed. A numerical example about bus runs assignment optimization of a single line is given to demonstrate the efficiency of the proposed methodology, showing that optimizing buses’ departure time using dynamic programming can save computational time and find the global optimal solution.

  3. Large truck and bus crash facts, 2008. 

    Science.gov (United States)

    2010-03-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2008. Selected crash statistics on passenger : vehicles are also presen...

  4. CFD Investigation on Long-Haul Passenger Bus

    Science.gov (United States)

    Tan, C. F.; Tee, B. T.; Law, H. C.; Lim, T. L.

    2015-09-01

    Air flow distribution is one of the important factors that will influence the bus passenger comfort during long haul travel. Poor air flow distribution not only cause discomfort to the bus passenger but also influence their travel mode as well. The main purpose of this study is to investigate the air flow performance of the bus air-conditioning system through CFD simulation approach. A 3D CAD model of air ducts was drawn and hence analysed by using CFD software, namely ANSYS Fluent, to determine the airflow rate for every outlets of the air-conditioning system. The simulated result was then validated with experimental data obtained from prototype model of air duct. Based on the findings, new design concepts is proposed with the aim to meet the industry requirement as well as to improve the bus passenger comfort during long haul travel.

  5. Transit bus applications of lithium ion batteries : progress and prospects

    Science.gov (United States)

    2012-12-31

    This report provides an overview of diverse transit bus applications of advanced Lithium Ion Batteries (LIBs). The report highlights and illustrates several FTA programs that fostered the successful development, demonstration, and deployment of fuel-...

  6. Analysis of movable bus stop boarding and alighting areas.

    Science.gov (United States)

    2013-05-01

    This study explored the feasibility of using movable and reusable boarding and alighting (B&A) pads at bus stops. : Potential design alternatives in terms of materials and structural support for these pads were evaluated. The review : focused on the ...

  7. Southwest Direct Express Bus Demonstration in Orlando, FL

    Science.gov (United States)

    1988-04-01

    In August 1983, the Orange-Seminole-Osceola Transit Authority (OSOTA) initiated six express bus routes in the southwest corridor of Orlando (known collectively as the Southwest Direct) as an UMTA-funded demonstration project. While one objective of t...

  8. Black silicon solar cells with black bus-bar strings

    DEFF Research Database (Denmark)

    Davidsen, Rasmus Schmidt; Tang, Peter Torben; Mizushima, Io

    2016-01-01

    We present the combination of black silicon texturing and blackened bus-bar strings as a potential method for obtaining all-black solar panels, while using conventional, front-contacted solar cells. Black silicon was realized by maskless reactive ion etching resulting in total, average reflectance...... below 0.5% across a 156x156 mm2 silicon wafer. Four different methods to obtain blackened bus-bar strings were compared with respect to reflectance, and two of these methods (i.e., oxidized copper and etched solder) were used to fabricate functional allblack solar 9-cell panels. The black bus-bars (e.......g., by oxidized copper) have a reflectance below 3% in the entire visible wavelength range. The combination of black silicon cells and blackened bus-bars results in aesthetic, all-black panels based on conventional, front-contacted solar cells without compromising efficiency....

  9. Understanding Factors of Distraction among Intrastate Bus Driver

    Directory of Open Access Journals (Sweden)

    Yunos Muhammad Nur Annuar Mohd

    2017-01-01

    Full Text Available The increase in number of the world population have affected the demand for public transport especially in larger cities. Intrastate buses are chosen as the main public transport by many people due to its affordable fares. Therefore, a better performance of the intrastate bus drivers would be significant to cater the high demand. Nevertheless, distraction among the intrastate bus drivers have been found as one of the major factors that could affect the performance of the drivers. Therefore, the objective of this paper is to provide a better understanding on the factors of distraction among intrastate bus drivers. This paper refers to findings from previous researches which are related to this field of study. In conclusion, this paper will provide a list of factors of distraction among the intrastate bus drivers which may degrade their performance.

  10. FTA fuel cell bus program : research accomplishments through 2011.

    Science.gov (United States)

    2012-03-01

    Prepared by the Federal Transit Administration (FTA) Office of Research, Demonstration, and Innovation (TRI), this report summarizes the accomplishments of fuel-cell-transit-bus-related research and demonstrations projects supported by FTA through 20...

  11. Modelling Field Bus Communications in Mixed-Signal Embedded Systems

    Directory of Open Access Journals (Sweden)

    Alassir Mohamad

    2008-01-01

    Full Text Available Abstract We present a modelling platform using the SystemC-AMS language to simulate field bus communications for embedded systems. Our platform includes the model of an I/O controller IP (in this specific case an C controller that interfaces a master microprocessor with its peripherals on the field bus. Our platform shows the execution of the embedded software and its analog response on the lines of the bus. Moreover, it also takes into account the influence of the circuits's I/O by including their IBIS models in the SystemC-AMS description, as well as the bus lines imperfections. Finally, we present simulation results to validate our platform and measure the overhead introduced by SystemC-AMS over a pure digital SystemC simulation.

  12. Modelling Field Bus Communications in Mixed-Signal Embedded Systems

    Directory of Open Access Journals (Sweden)

    Patrick Garda

    2008-08-01

    Full Text Available We present a modelling platform using the SystemC-AMS language to simulate field bus communications for embedded systems. Our platform includes the model of an I/O controller IP (in this specific case an I2C controller that interfaces a master microprocessor with its peripherals on the field bus. Our platform shows the execution of the embedded software and its analog response on the lines of the bus. Moreover, it also takes into account the influence of the circuits's I/O by including their IBIS models in the SystemC-AMS description, as well as the bus lines imperfections. Finally, we present simulation results to validate our platform and measure the overhead introduced by SystemC-AMS over a pure digital SystemC simulation.

  13. STRATEGI PENGEMBANGAN TRANSPORTASI WISATA KURA-KURA BUS DI BALI

    Directory of Open Access Journals (Sweden)

    Ayu Kusuma

    2018-01-01

    Full Text Available Kura-Kura Bus is one of tourist transportation companies in Bali with public shuttle bus service in tourism route. Data analysis in this research were using SWOT and AHP analysis, with participants who have position minimal as a supervisor. Participants selected based on their expertise and relevance with this article. Based on the results of SWOT and AHP analysis to develop tourist transportation is Kura-Kura Bus, which is considered the most realistic scenario is an optimistic scenario, with the goal to be a safe and comfortable transportation. To achieve the goal, based on priority strategies that could be done by management of Kura-Kura Bus are developing unique products, finding new markets, favoring public transport services, enchance brand reputation, developing smartphone application, and cross promotion with supplier.

  14. The problem of the pillion rider: India's helmet law and New Delhi's exemption.

    Science.gov (United States)

    Swaroop, Mamta; Marie Siddiqui, Selma; Sagar, Sushma; Crandall, Marie L

    2014-05-01

    In India, motorized two-wheeler (MTW) road traffic accidents injure or kill 72,000 women annually. Before the Motor Vehicle Act of 1988, which required mandatory helmet use for MTW riders, a study found 0.6% of all MTW pillions (backseat passengers) were helmeted. Citing religious protests to the legislation, Delhi's high court exempted the city's 12 million women from the law. We hypothesize that currently male pillions use helmets more frequently than females, and that overall pillion helmet usage has increased over the last 20 y. Continuous video was recorded in half-hour blocks at four locations in Delhi on separate days, totaling 8 hours of high- and low-volume traffic. Videos were reviewed with at least two reviewers extracting the number of MTW pillions, as well as their gender, approximate age, and helmet usage. Of 4010 pillions identified, 63.8% were male, 32.4% female, and 3.3% children. Among males, there were significantly more helmeted pillions (88.4%, P < 0.001); among females, there were significantly more unhelmeted pillions (99.4%, P < 0.001). Among unhelmeted pillions, significantly more were female (81.4%) than male (P < 0.001). Current overall pillion helmet use is significantly higher than historical rate (P < 0.001). The significantly higher male pillion helmet usage compared with females indicates Delhi's helmet law is associated with increased compliance among those who fall under its jurisdiction. This augments the growing body of evidence that mandatory helmet laws are efficacious, thus repealing the exemption of women is an important step in increasing female pillion helmet usage. Copyright © 2014 Elsevier Inc. All rights reserved.

  15. DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Elana M. Chapman; Shirish Bhide; Jennifer Stefanik; Howard Glunt; Andre L. Boehman; Allen Homan; David Klinikowski

    2003-04-01

    The objectives of this research and demonstration program are to convert a campus shuttle bus to operation on dimethyl ether, a potential ultra-clean alternative diesel fuel. To accomplish this objective, this project includes laboratory evaluation of a fuel conversion strategy, as well as, field demonstration of the DME-fueled shuttle bus. Since DME is a fuel with no lubricity (i.e., it does not possess the lubricating quality of diesel fuel), conventional fuel delivery and fuel injection systems are not compatible with dimethylether. Therefore, to operate a diesel engine on DME one must develop a fuel-tolerant injection system, or find a way to provide the necessary lubricity to the DME. In this project, they have chosen the latter strategy in order to achieve the objective with minimal need to modify the engine. The strategy is to blend DME with diesel fuel, to obtain the necessary lubricity to protect the fuel injection system and to achieve low emissions. The bulk of the efforts over the past year were focused on the conversion of the campus shuttle bus. This process, started in August 2001, took until April 2002 to complete. The process culminated in an event to celebrate the launching of the shuttle bus on DME-diesel operation on April 19, 2002. The design of the system on the shuttle bus was patterned after the system developed in the engine laboratory, but also was subjected to a rigorous failure modes effects analysis with help from Dr. James Hansel of Air Products. The result of this FMEA was the addition of layers of redundancy and over-pressure protection to the system on the shuttle bus. The system became operation in February 2002. Preliminary emissions tests and basic operation of the shuttle bus took place at the Pennsylvania Transportation institute's test track facility near the University Park airport. After modification and optimization of the system on the bus, operation on the campus shuttle route began in early June 2002. However, the

  16. Scenario-based electric bus operation: A case study of Putrajaya, Malaysia

    OpenAIRE

    Lay Eng Teoh; Hooi Ling Khoo; Siew Yoke Goh; Lai Mun Chong

    2018-01-01

    Globally, transportation sector has emerged as one of the major sources of air pollution. Correspondingly, green mobility (with electric bus) is gaining increasing attention as an essential step to mitigate emission concern. As such, a proper electric bus network design and fleet planning is important especially for bus operator to acquire an adequate number of electric bus, right on time, in order to operate electric bus system viably. Thus, this paper aims to examine the possibility to oper...

  17. Regenerative Braking System for Series Hybrid Electric City Bus

    OpenAIRE

    Zhang, Junzhi; Lu, Xin; Xue, Junliang; Li, Bos

    2008-01-01

    Regenerative Braking Systems (RBS) provide an efficient method to assist hybrid electric buses achieve better fuel economy while lowering exhaust emissions. This paper describes the design and testing of three regenerative braking systems, one of which is a series regenerative braking system and two of which are parallel regenerative braking systems. The existing friction based Adjustable Braking System (ABS) on the bus is integrated with each of the new braking systems in order to ensure bus...

  18. Digital bus technology in new coal-fired plants

    Energy Technology Data Exchange (ETDEWEB)

    Blaney, J.; Murray, J. [Emerson Process Management (United States)

    2007-10-15

    The main issues associated with including digital bus technology such as Foundation fieldbus, Profibus-DP or DeviceNet, in a coal-fired power plant are deciding which systems to install and determining how to implement it. Although still new, digital bus experiences to date have shown that the technology performs solidly and when wiring best practices are followed a significantly shorted commissioning cycle can be achieved. 1 fig., 2 tabs.

  19. VHDL resolved function based inner communication bus for FPGA

    Science.gov (United States)

    Pozniak, Krzysztof T.

    2017-08-01

    This article discusses a method of building an internal, universal and parametric bus. The solution was designed for a variety of FPGA families and popular VHDL compilers. The algorithm of automatic configuration of address space and methods of receiving and sending addressed data are discussed. The basic solution realized in VHDL language in a behavioral form and chosen examples of practical use of the internal bus are presented in detail.

  20. Analysing passenger arrivals rates and waiting time at bus stops

    OpenAIRE

    Kaparias, I.; Rossetti, C.; Trozzi, V.

    2015-01-01

    The present study investigates the rather under-explored topic of passenger waiting times at public transport facilities. Using data collected from part of London’s bus network by means of physical counts, measurements and observations, and complemented by on-site passenger interviews, the waiting behaviour is analysed for a number of bus stops served by different numbers of lines. The analysis employs a wide range of statistical methods and tools, and concentrates on three aspects: passenger...

  1. Leading Schools through Major Change

    Science.gov (United States)

    Syed, Sarosh

    2013-01-01

    Changing even the smallest things in schools is hard--just ask any principal who has overseen a rescheduling of bus routes. So imagine the difficulty of getting a school to move its curriculum and instruction from familiar learning requirements to brand-new nationwide standards. Yet this is exactly the sort of change public schools in 45 states…

  2. Effect of passenger position on fear of danger experienced during sudden bus stops.

    Science.gov (United States)

    Aoki, Takeo; Uetake, Teruo; Shimoda, Masahiro

    2009-06-01

    The purpose of this study was to identify the effect of bus passengers' positions on their fear of danger when a bus stopped suddenly. A temporary bus running course with one bus stop was set up on the campus of the Tokyo University of Agriculture and Technology (TUAT). The bus ran the course 14 times with the bus stopping twice during the course, once at the bus stop and again just after re-starting from the bus stop. The driver was asked to brake more strongly than usual when stopping. Sixteen students (15 males and 1 female) between the ages of 18 and 21 years participated. In turn, all participants were asked to take 14 different postures in the bus. Participants were also asked to report their level of fear on a rating scale each time the bus stopped. The study showed that (1) passengers' fear of danger at the first sudden stop was typically higher than that at the second stop, (2) standing passengers who held hand straps experienced more fear than those who held fixed safety devices, (3) bus passengers sitting on the centre of the rear seat had a great risk of injury if the bus stopped suddenly, and (4) when passengers faced the window and stood transversely with respect to from the moving direction of the bus and the bus stopped suddenly, passengers' fear of danger was affected by the side of the bus on which they stood as well as which hand they used to grasp a safety device.

  3. CROSS-FRONTIER PUBLIC TRANSPORT: Y BUS

    CERN Multimedia

    CERN Housing Service

    2002-01-01

    'Y' buses cover the journey between Val Thoiry in France (shopping centre including'Migros' and other stores) and Blandonnet in Switzerland, where they stop outside the 'Jumbo' shop, now renamed 'Carrefour'. In France, the buses connect up Thoiry, Sergy and St. Genis, then cross the border to stop outside CERN, Meyrin, before continuing towards Geneva along the 'Route de Meyrin', stopping outside the 'La Tour' hospital, then at the terminus Blandonnet. The normal fare on French territory with a slight incursion into Switzerland for this purpose as far as CERN, Meyrin, is 1.20 Euros per single journey (ticket valid for one hour). The same amount is charged for any single journey in Switzerland. For example, the cost of a single journey between St. Genis and the 'La Tour' hospital would be 2.40 Euros. The season ticket ('Abonnement de Travail') opens the right to purchase a ticket valid over any period of seven days which entitles the holder to as many journeys as required between the bus stop nearest to the pl...

  4. DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Elana M. Chapman; Shirish Bhide; Jennifer Stefanik; Howard Glunt; Andre L. Boehman; Allen Homan; David Klinikowski

    2003-04-01

    The objectives of this research and demonstration program are to convert a campus shuttle bus to operation on dimethyl ether, a potential ultra-clean alternative diesel fuel. To accomplish this objective, this project includes laboratory evaluation of a fuel conversion strategy, as well as, field demonstration of the DME-fueled shuttle bus. Since DME is a fuel with no lubricity (i.e., it does not possess the lubricating quality of diesel fuel), conventional fuel delivery and fuel injection systems are not compatible with dimethyl ether. Therefore, to operate a diesel engine on DME one must develop a fuel-tolerant injection system, or find a way to provide the necessary lubricity to the DME. In this project, they have chosen the latter strategy in order to achieve the objective with minimal need to modify the engine. Their strategy is to blend DME with diesel fuel, to obtain the necessary lubricity to protect the fuel injection system and to achieve low emissions. The bulk of the efforts over the past year were focused on the conversion of the campus shuttle bus. This process, started in August 2001, took until April 2002 to complete. The process culminated in an event to celebrate the launching of the shuttle bus on DME-diesel operation on April 19, 2002. The design of the system on the shuttle bus was patterned after the system developed in the engine laboratory, but also was subjected to a rigorous failure modes effects analysis (FMEA, referred to by Air Products as a ''HAZOP'' analysis) with help from Dr. James Hansel of Air Products. The result of this FMEA was the addition of layers of redundancy and over-pressure protection to the system on the shuttle bus. The system became operational in February 2002. Preliminary emissions tests and basic operation of the shuttle bus took place at the Pennsylvania Transportation Institute's test track facility near the University Park airport. After modification and optimization of the system on

  5. Environmental Assessment of Bus Transport in the Trondheim Region - Evaluation of Relevant Bus and Fuel Technologies and their Potential for Mitigating Emissions from Passenger Transportation

    OpenAIRE

    Buø, Tonje

    2015-01-01

    The overall aim of this thesis is to assess the carbon footprint of transport by bus in the Trondheim region. Bus transportation is promoted as a strategy both to combat local pollution problems in urban areas and to mitigate global greenhouse gas emissions from passenger transport. Still, the environmental impacts of bus transport have received fairly limited attention in research. The environmental impacts of bus transport are calculated through life cycle assessment. A model is develo...

  6. SmartDriver for school bus : participant's handbook

    International Nuclear Information System (INIS)

    2007-01-01

    SmartDriver is a key component of Natural Resources Canada's ecoENERGY for fleets program. The aim of the ecoENERGY initiative is to introduce fleets to energy-efficient practices for reducing fuel consumption and emissions and to help drivers adopt the driving practices outlined in the SmartDriver training materials. The handbook was designed as part of a comprehensive media package that included a CD-ROM with audio-visual components. The package was developed as a training strategy for fuel-efficient driving skills. The first module contained information on air pollution and techniques that drivers can adopt to reduce particulate matter, smog, greenhouse gas (GHG) emissions. An outline of new engine technologies developed to reduce emissions was also provided. The second module discussed various vehicle factors that influence fuel efficiency. Alternative fuels were reviewed, and vehicle components were discussed in relation to improving fuel economy. The module also included preventive maintenance tips as well as engine starting techniques and methods for reducing time spent idling. Various activities and games related to improving fuel efficiency were also included. 17 figs

  7. An evaluation of a lane support system for bus rapid transit on narrow shoulders and the relation to bus driver mental workload

    NARCIS (Netherlands)

    Ward, Nicholas J.; Shankwitz, Craig; Gorgestani, Alec; Donath, Max; De Waard, Dick; Boer, Erwin R.

    2006-01-01

    The use of dedicated bus shoulders is a key method for implementing bus rapid transit (BRT) in areas that do not have the space for additional infrastructure. However, the narrow width of the bus shoulder and the need to anticipate traffic hazards in the adjacent lane can both be significant

  8. An Improved Model for Headway-Based Bus Service Unreliability Prevention with Vehicle Load Capacity Constraint at Bus Stops

    Directory of Open Access Journals (Sweden)

    Weiya Chen

    2012-01-01

    Full Text Available This paper presents an improved model for improving headway-based bus route service reliability at bus stops using real-time preventive operation control, taking into account dynamic interaction among random passenger demand, stochastic driving conditions of route segments, and vehicle load capacity constraint. In this model, the real-time information of passenger demand and vehicle operation is involved to predict the imminent unacceptable headway deviation, in the case of which some in-time preventive control strategies are deployed according to the given control rules. As a case study, a single fixed bus route with high-frequency services was simulated and different scenarios of real-time preventive operation control were performed. Headway adherence and average passenger wait time were used to measure bus service reliability. The results show that the improved model is closer to the real bus route service, and using real-time information to predict potential service unreliability and trigger in-time preventive control can reduce bus bunching and avoid big gap.

  9. ANALISIS SARANA ANGKUTAN UMUM BUS DAMRI DI KOTA SEMARANG

    Directory of Open Access Journals (Sweden)

    Subhan Rizal Amin

    2015-12-01

    Full Text Available This study aims to analyze the availability and use of public transportation by taking a case study of the Damri bus which has Ngaliyan-Pucanggading route. The availability of public transport is not comparable to the demand for public transportation services so that the problems of transportation emerge. Additionally, the use of public transport becomes an important factor to develop the transportation. The study is conducted by surveying the Damri passengers of B.04 lane and logistic regression is used for the analysis. The method of determining the needs of transportation is issued by Departemen Perhubungan. It is used to calculate and determine whether the public transportation should be added or reduced. Then, the factors used as the independent variables in the analysis are the Damri’s safety, effectiveness, efficiency, service and reliability. The results show that Perum Damri does not need to add more Damri bus for B.04 because the results’ calculation is 0.6. and the factors that significantly influence the use Damri bus is the variable of safety, effectiveness and efficiency. However, the variables of service and reliability do not significantly influence the use of B.04 Damri bus.Penelitian ini bertujuan untuk menganalisis ketersediaan dan penggunaan angkutan sarana angkutan umum penumpang dengan mengambil studi kasus pada bus Damri jalur dengan trayek Ngaliyan-Pucanggading. Ketersediaan sarana angkutan umum yang tersedia tidak sebanding dengan besarnya permintaan akan jasa angkutan umum oleh masyarakat umum sehingga muncul permasalahan transportasi. Di samping itu, penggunaan angkutan umum yang beroperasi menjadi faktor penting dalam upaya pengembangan sarana transportasi. Penelitian ini dilakukan dengan menggunakan metode survey terhadap para penumpang bus Damri jalur B.04 dan dianalisis dengan Regresi Logistik. Metode penentuan kebutuhan armada dikeluarkan oleh Departemen Perhubungan yang digunakan untuk menghitung apakah suatu

  10. Schedule and complex motion of shuttle bus induced by periodic inflow of passengers

    International Nuclear Information System (INIS)

    Nagatani, Takashi; Naito, Yuichi

    2011-01-01

    We have studied the dynamic behavior of a bus in the shuttle bus transportation with a periodic inflow. A bus schedule is closely related to the dynamics. We present the modified circle map model for the dynamics of the shuttle bus. The motion of the shuttle bus depends on the loading parameter and the inflow period. The shuttle bus displays the periodic, quasi-periodic, and chaotic motions with varying both loading parameter and inflow rate. -- Highlights: → We studied the dynamic behavior of a bus in the shuttle bus transportation. → We presented the modified circle map model for the bus schedule. → We clarified the dependence of the tour time on both loading parameter and inflow period.

  11. Improvement of multiprocessing performance by using optical centralized shared bus

    Science.gov (United States)

    Han, Xuliang; Chen, Ray T.

    2004-06-01

    With the ever-increasing need to solve larger and more complex problems, multiprocessing is attracting more and more research efforts. One of the challenges facing the multiprocessor designers is to fulfill in an effective manner the communications among the processes running in parallel on multiple multiprocessors. The conventional electrical backplane bus provides narrow bandwidth as restricted by the physical limitations of electrical interconnects. In the electrical domain, in order to operate at high frequency, the backplane topology has been changed from the simple shared bus to the complicated switched medium. However, the switched medium is an indirect network. It cannot support multicast/broadcast as effectively as the shared bus. Besides the additional latency of going through the intermediate switching nodes, signal routing introduces substantial delay and considerable system complexity. Alternatively, optics has been well known for its interconnect capability. Therefore, it has become imperative to investigate how to improve multiprocessing performance by utilizing optical interconnects. From the implementation standpoint, the existing optical technologies still cannot fulfill the intelligent functions that a switch fabric should provide as effectively as their electronic counterparts. Thus, an innovative optical technology that can provide sufficient bandwidth capacity, while at the same time, retaining the essential merits of the shared bus topology, is highly desirable for the multiprocessing performance improvement. In this paper, the optical centralized shared bus is proposed for use in the multiprocessing systems. This novel optical interconnect architecture not only utilizes the beneficial characteristics of optics, but also retains the desirable properties of the shared bus topology. Meanwhile, from the architecture standpoint, it fits well in the centralized shared-memory multiprocessing scheme. Therefore, a smooth migration with substantial

  12. Scenario-based electric bus operation: A case study of Putrajaya, Malaysia

    Directory of Open Access Journals (Sweden)

    Lay Eng Teoh

    2018-03-01

    Full Text Available Globally, transportation sector has emerged as one of the major sources of air pollution. Correspondingly, green mobility (with electric bus is gaining increasing attention as an essential step to mitigate emission concern. As such, a proper electric bus network design and fleet planning is important especially for bus operator to acquire an adequate number of electric bus, right on time, in order to operate electric bus system viably. Thus, this paper aims to examine the possibility to operate electric bus as a replacement for the conventional bus operation (with natural gas buses for the study area in Putrajaya, Malaysia. In order to determine a proper-designed electric bus operating system in terms of electric bus route, service frequency and quantity, the proposed methodology is developed with the aid of a traffic modeling software to cater various scenarios. Based on the existing (conventional traffic and transit system in Putrajaya, the developed electric bus operating model is calibrated accordingly by considering various operational concerns including battery capacity and charging facility. The resultant findings revealed that the developed electric bus operating system in Putrajaya outperforms the conventional bus operation, not only in generating a higher profit margin for the bus operator, but also satisfying the passengers in a better manner (by carrying more passengers per unit of bus with a lower energy consumption.

  13. Potential Influence of Metro on Bus: A Case Study

    Science.gov (United States)

    Selvakumar, M.; Abishek Reddy, M.; Sathish, V.; Venkatesh, R.

    2018-06-01

    A modal shift occurs when one mode of transport has a comparative advantage in a similar market over another. The present work concerns with the development of modal shift model for urban travel in Chennai, India. The modal shift model was calibrated using binary logit technique and validated using hold-out sample method. The validated model was used to predict the probability of shift in selected corridor. The recent introduction of metro rail in Chennai has lead to an increasing competition among public transport modes. To study the influence of metro on bus transport, a Stated Preference (SP) survey was conducted among express bus travellers. Using the SP survey data, a modal shift model was calibrated to estimate the plausible shift from bus to metro. Results indicate that variables like fare- difference, age, and income play an important role in the shift behaviour. When metro fare increases with respect to express bus fare, bus passengers are less willing to use metro and vice-versa.

  14. 1393 Ring Bus at JPL: Description and Status

    Science.gov (United States)

    Wysocky, Terry R.

    2007-01-01

    Completed Ring Bus IC V&V Phase - Ring Bus Test Plan Completed for SIM Project - Applicable to Other Projects Implemented a Avionics Bus Based upon the IEEE 1393 Standard - Excellent Starting Point for a General Purpose High-Speed Spacecraft Bus - Designed to Meet SIM Requirements for - Real-time deterministic, distributed systems. - Control system requirements - Fault detection and recovery Other JPL Projects Considering Implementation F'light Software Ring Bus Driver Module Began in 2006, Continues Participating in Standard Revision. Search for Earth-like planets orbiting nearby stars and measure the masses and orbits of the planets it finds. Survey 2000 nearby stars for planetary systems to learn whether our Solar System is unusual, or typical. Make a new catalog of star position 100 times more accurate than current measurements. Learn how our galaxy formed and will evolve by studying the dynamics of its stars. Critically test models of exactly how stars shine, including exotic objects like black holes, neutron stars and white dwarfs.

  15. A new MV bus transfer scheme for nuclear power plants

    International Nuclear Information System (INIS)

    Chang, C.K.

    2015-01-01

    The auxiliary power system of many generating stations consists of offsite power supply system and onsite power supply system, including emergency diesel generators (EDG) to provide secure power to auxiliary loads. If a normal power supply fails to supply power, then the power source is transferred to a standby power supply. In the case of nuclear power plants (NPP), the unit auxiliary transformer (UAT) and standby auxiliary transformer (SAT) - or station service transformer - are installed and powered from 2 offsite power circuits to meet regulatory requirements. The transfer methods of a motor bus from a normal source to a standby source used in power generating stations are fast bus transfer, in-phase transfer, or residual transfer. Fast bus transfer method is the most popular and residual voltage transfer method that is used as a backup in medium voltage buses in general. The use of the advanced technology like open circuit voltage prediction and digital signal processing algorithms can improve the reliability of fast transfer scheme. However, according to the survey results of the recent operation records in nuclear power plants, there were many instances where the fast transfer scheme has failed. To assure bus transfer in any conditions and circumstances, un-interruptible bus transfer scheme utilizing the state of the art medium voltage UPS (Un-interruptible Power Supply) is discussed and elaborated

  16. Bus network redesign for inner southeast suburbs of Melbourne, Australia

    Science.gov (United States)

    Pandangwati, S. T.; Milyanab, N. A.

    2017-06-01

    Public transport is the most effective mode of transport in the era of climate change and oil depletion. It can address climate change issues by reducing urban greenhouse gas emission and oil consumption while at the same time improving mobility. However, many public transport networks are not effective and instead create high operating costs with low frequencies and occupancy. Melbourne is one example of a metropolitan area that faces this problem. Even though the city has well-integrated train and tram networks, Melbourne’s bus network still needs to be improved. This study used network planning approach to redesign the bus network in the City of Glen Eira, a Local Government Area (LGA) in the southeastern part of Metropolitan Melbourne. The study area is the area between Gardenvale North and Oakleigh Station, as well as between Caulfield and Patterson Stations. This area needs network improvement mainly because of the meandering bus routes that run within it. This study aims to provide recommendations for improving the performance of bus services by reducing meandering routes, improving transfer point design and implementing coordinated timetables. The recommendations were formulated based on a ‘ready-made’ concept to increase bus occupancy. This approach can be implemented in other cities with similar problems and characteristics including those in Indonesia.

  17. Potential Influence of Metro on Bus: A Case Study

    Science.gov (United States)

    Selvakumar, M.; Abishek Reddy, M.; Sathish, V.; Venkatesh, R.

    2018-03-01

    A modal shift occurs when one mode of transport has a comparative advantage in a similar market over another. The present work concerns with the development of modal shift model for urban travel in Chennai, India. The modal shift model was calibrated using binary logit technique and validated using hold-out sample method. The validated model was used to predict the probability of shift in selected corridor. The recent introduction of metro rail in Chennai has lead to an increasing competition among public transport modes. To study the influence of metro on bus transport, a Stated Preference (SP) survey was conducted among express bus travellers. Using the SP survey data, a modal shift model was calibrated to estimate the plausible shift from bus to metro. Results indicate that variables like fare-difference, age, and income play an important role in the shift behaviour. When metro fare increases with respect to express bus fare, bus passengers are less willing to use metro and vice-versa.

  18. Driving a Bus in India: A Study of Indore Bus Rapid Transport System

    Directory of Open Access Journals (Sweden)

    Siddhartha K. RASTOGI

    2017-12-01

    Full Text Available Indore is a typical tier-2 town in the central province of India, fast becoming a regional commercial hub in an economically booming state. The city has a population of over 2 million with no significant public transport. Among the multiple options available, the city started implementing a dedicated corridor based Bus Rapid Transport System (BRTS. The project was jointly mooted by the central, state, and city authorities. However, the system encountered a range of problems, including conflicts and pulls between multiple implementing agencies, delays in delivery of hardware and constructions, land acquisition and compensation, vested interests, public interest litigations, and court orders. The paper analyses the BRTS, introduced in Indore in the midst of 2013, from multiple party perspectives with an underlying search for public policy and public management insights. The broad results indicate feasibility and desirability of the project; however, real problems emerge in public and public perception management.

  19. 26 CFR 48.4221-8 - Tax-free sales of tires, tubes, and tread rubber used on intercity, local, and school buses.

    Science.gov (United States)

    2010-04-01

    ... if the bus has a passenger seating capacity of at least 20 adults and the transportation is available... of a school. Incidental use (deadheading) of the school bus without passengers to or from a point to... used on intercity, local, and school buses. 48.4221-8 Section 48.4221-8 Internal Revenue INTERNAL...

  20. Optimal Locations of Bus Stops Connecting Subways near Urban Intersections

    Directory of Open Access Journals (Sweden)

    Yuan Cui

    2015-01-01

    Full Text Available Unsuitable locations of bus stops which provide feeder transportation connecting subways near urban intersections usually lead to the low efficiency of public transport and level of passenger service. A multiobjective optimization model to distribute such stop locations is proposed to attain the shortest total walk distance of passengers and minimum delay time of cars through intersections and travel time of buses. The Pareto frontier and optimal solutions for the proposed model are given by the distance-based and enumerative methods. The Xizhimen bus stop is selected to implement case studies for verifying the validity of the proposed model. The analysis of sensitivity on possible solutions is also carried out in the case studies. The results show that the proposed model is capable of optimizing the locations of bus stops connecting subways near intersections and helpful to improve the level of passengers service and operational efficiency of public transportation.

  1. American Fuel Cell Bus Project Evaluation. Second Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2015-09-01

    This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses operating in the Coachella Valley area of California. The prototype AFCB was developed as part of the Federal Transit Administration's (FTA's) National Fuel Cell Bus Program. Through the non-profit consortia CALSTART, a team led by SunLine Transit Agency and BAE Systems developed a new fuel cell electric bus for demonstration. SunLine added two more AFCBs to its fleet in 2014 and another in 2015. FTA and the AFCB project team are collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory to evaluate the buses in revenue service. This report summarizes the performance results for the buses through June 2015.

  2. Rethinking passive transport: bus fare exemptions and young people's wellbeing.

    Science.gov (United States)

    Jones, Alasdair; Steinbach, Rebecca; Roberts, Helen; Goodman, Anna; Green, Judith

    2012-05-01

    Much recent public health research has emphasised the health impacts for young people of 'active travel' modes, typically defined as walking and cycling. Less research has focused on public transport modes. Drawing on qualitative data, we examine the links between bus travel and wellbeing in London, where young people currently have free bus travel. Our findings indicate that bus travel can be both a physically and socially active experience for young people. We suggest a more nuanced understanding of 'active travel' is now needed, alongside greater attention to urban public transport networks as key sites that impact on important determinants of wellbeing such as independent mobility and social inclusion. Copyright © 2012 Elsevier Ltd. All rights reserved.

  3. RS-485 Bus Design of a Missile Simulation Training System

    Directory of Open Access Journals (Sweden)

    Liu Fang

    2013-07-01

    Full Text Available In a missile simulation training system with one-master and multi-slaves distributed system structure, a universal controller is necessary due to the system composed with several controllers. In this research, the designed controllers communicate with each other and upper control computer through RS-485 field bus. RS-485 bus including interface circuits, transmission protocol, Cyclic Redundancy Check (CRC method and upper control test software is designed and proposed. The universal controller adopting the designed RS-485 interface circuits is connected through twisted-pair and makes the simulation system, then the controller is tested in line. The results show that the RS-485 bus communicates effectively using the protocol and CRC method, data transmission rates reaches 115.2 kbps, and has a good stability.

  4. DESIGN OF CITY BUS LIFT FOR THE HANDICAPPEDS

    Directory of Open Access Journals (Sweden)

    K. Turgut GÜRSEL

    2003-03-01

    Full Text Available Although the technological developments, the handicappeds do not take part sufficiently in the social and economic life, because buildings, road construction features and means of the transport are not suitable for them. In this study, a lift for handicappeds was designed, that is supposed to be installed to the middle door of city buses. The lift, whose installation should require a few changes at the bus, is driven by a hydraulic system from the street to the level of the bus floor and vice-versa. In the work, at first a construction was developed in accordance with the dimensions of the middle door of a city bus. After determining of dimensions of all elements, a hydraulic mechanism was constructed, that raises the handicapped, its wheelchair and the platform. Furthermore the construction of the elements of the system were determined, and its proofs of strength analysis were indicated

  5. Spatial analysis of bus transport networks using network theory

    Science.gov (United States)

    Shanmukhappa, Tanuja; Ho, Ivan Wang-Hei; Tse, Chi Kong

    2018-07-01

    In this paper, we analyze the bus transport network (BTN) structure considering the spatial embedding of the network for three cities, namely, Hong Kong (HK), London (LD), and Bengaluru (BL). We propose a novel approach called supernode graph structuring for modeling the bus transport network. A static demand estimation procedure is proposed to assign the node weights by considering the points of interests (POIs) and the population distribution in the city over various localized zones. In addition, the end-to-end delay is proposed as a parameter to measure the topological efficiency of the bus networks instead of the shortest distance measure used in previous works. With the aid of supernode graph representation, important network parameters are analyzed for the directed, weighted and geo-referenced bus transport networks. It is observed that the supernode concept has significant advantage in analyzing the inherent topological behavior. For instance, the scale-free and small-world behavior becomes evident with supernode representation as compared to conventional or regular graph representation for the Hong Kong network. Significant improvement in clustering, reduction in path length, and increase in centrality values are observed in all the three networks with supernode representation. The correlation between topologically central nodes and the geographically central nodes reveals the interesting fact that the proposed static demand estimation method for assigning node weights aids in better identifying the geographically significant nodes in the network. The impact of these geographically significant nodes on the local traffic behavior is demonstrated by simulation using the SUMO (Simulation of Urban Mobility) tool which is also supported by real-world empirical data, and our results indicate that the traffic speed around a particular bus stop can reach a jammed state from a free flow state due to the presence of these geographically important nodes. A comparison

  6. Walk, Bicycle, and Transit Trips of Transit-Dependent and Choice Riders in the 2009 United States National Household Travel Survey.

    Science.gov (United States)

    Lachapelle, Ugo

    2015-08-01

    Previous research has shown that public transit use may be associated with active transportation. Access to a car may influence active transportation of transit riders. Using the 2009 United States National Household Travel Survey (NHTS), transit users ≥ 16 years old (n = 25,550) were categorized according to driver status and number of cars and drivers in the household. This typology ranged from choice transit riders (ie, "fully motorized drivers") to transit-dependent riders (ie, "unmotorized nondriver"). Transit trips, walking trips, and bicycling trips of transit users are estimated in negative binomial models against the car availability typology. Sixteen percent of participants took transit in the past month; most (86%) lived in car-owning households. As income increased, car availability also increased. Transit user groups with lower car availability were generally more likely than fully motorized drivers to take more public transit, walking, and bicycle trips. Transit riders have varying levels of vehicle access; their use of combinations of alternative modes of transportation fluctuates accordingly. Transit-dependent individuals without cars or sharing cars used active transportation more frequently than car owners. Policies to reduce vehicle ownership in households may enable increases in the use of alternative modes of transportation for transit users, even when cars are still owned.

  7. Primary or secondary tasks? Dual-task interference between cyclist hazard perception and cadence control using cross-modal sensory aids with rider assistance bike computers.

    Science.gov (United States)

    Yang, Chao-Yang; Wu, Cheng-Tse

    2017-03-01

    This research investigated the risks involved in bicycle riding while using various sensory modalities to deliver training information. To understand the risks associated with using bike computers, this study evaluated hazard perception performance through lab-based simulations of authentic riding conditions. Analysing hazard sensitivity (d') of signal detection theory, the rider's response time, and eye glances provided insights into the risks of using bike computers. In this study, 30 participants were tested with eight hazard perception tasks while they maintained a cadence of 60 ± 5 RPM and used bike computers with different sensory displays, namely visual, auditory, and tactile feedback signals. The results indicated that synchronously using different sense organs to receive cadence feedback significantly affects hazard perception performance; direct visual information leads to the worst rider distraction, with a mean sensitivity to hazards (d') of -1.03. For systems with multiple interacting sensory aids, auditory aids were found to result in the greatest reduction in sensitivity to hazards (d' mean = -0.57), whereas tactile sensory aids reduced the degree of rider distraction (d' mean = -0.23). Our work complements existing work in this domain by advancing the understanding of how to design devices that deliver information subtly, thereby preventing disruption of a rider's perception of road hazards. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Lightweight power bus for a baseload nuclear reactor in space

    International Nuclear Information System (INIS)

    Oberly, C.E.; Massie, L.D.; Hoffman, D.J.

    1989-01-01

    Space environmental interactions with the power distribution/power processing subsystem can become a serious problem for power systems rated at 10's to 100's of kilowatts. Utilization of ceramic superconductors at 1000 A/cm/sup 2/, which has already been demonstrated at 77 K in a conductor configuration may eliminate both bus mass and distribution voltage problems in a high power satellite. The analytical results presented here demonstrate that a superconducting coaxial power transmission bus offers significant benefits in reduced distribution voltage and mass

  9. Quantum bus of metal nanoring with surface plasmon polaritons

    International Nuclear Information System (INIS)

    Lin Zhirong; Guo Guoping; Tu Tao; Li Haiou; Zou Changling; Ren Xifeng; Guo Guangcan; Chen Junxue; Lu Yonghua

    2010-01-01

    We develop an architecture for distributed quantum computation using quantum bus of plasmonic circuits and spin qubits in self-assembled quantum dots. Deterministic quantum gates between two distant spin qubits can be reached by using an adiabatic approach in which quantum dots couple with highly detuned plasmon modes in a metallic nanoring. Plasmonic quantum bus offers a robust and scalable platform for quantum optics experiments and the development of on-chip quantum networks composed of various quantum nodes, such as quantum dots, molecules, and nanoparticles.

  10. Overview of Multi-DC-Bus Solutions for DC Microgrids

    DEFF Research Database (Denmark)

    Ricchiuto, D.; Mastromauro, R.A.; Liserre, Marco

    2013-01-01

    DC Microgrids have recently received a lot of attention in the last years due to high penetration of renewable energy sources as well as distributed energy storage systems. In the future DC microgrids could be preferable respect to AC microgrids in terms of redundancy since multi-DC-Bus solutions...... could provide a continuative power supply to the loads. An overview of Multi-DC-Bus solutions is presented in this paper. The performances are compared on the basis of possible DC microgrid configurations, redundancy, different DC voltage levels....

  11. Bus bays inventory using a terrestrial laser scanning system

    Directory of Open Access Journals (Sweden)

    Bobkowska Katarzyna

    2017-01-01

    Full Text Available This article presents the use of laser scanning technology for the assessment of bus bay geo-location. Ground laser scanning is an effective tool for collecting three-dimensional data. Moreover, the analysis of a point cloud dataset can be a source of a lot of information. The authors have outlined an innovative use of data collection and analysis using the TLS regarding information on the flatness of bus bays. The results were finalized in the form of colour three-dimensional maps of deviations and pavement type.

  12. Black silicon with black bus-bar strings

    DEFF Research Database (Denmark)

    Davidsen, Rasmus Schmidt; Tang, Peter Torben; Mizushima, Io

    2016-01-01

    We present the combination of black silicon texturing and blackened bus-bar strings as a potential method for obtaining all-black solar panels, while using conventional, front-contacted solar cells. Black silicon was realized by mask-less reactive ion etching resulting in total, average reflectance...... below 0.5% across a 156x156 mm2 silicon wafer. Black bus-bars were realized by oxidized copper resulting in reflectance below 3% in the entire visible wavelength range. The combination of these two technologies may result in aesthetic, all-black panels based on conventional, front-contacted solar cells...

  13. Design of temperature monitoring system based on CAN bus

    Science.gov (United States)

    Zhang, Li

    2017-10-01

    The remote temperature monitoring system based on the Controller Area Network (CAN) bus is designed to collect the multi-node remote temperature. By using the STM32F103 as main controller and multiple DS18B20s as temperature sensors, the system achieves a master-slave node data acquisition and transmission based on the CAN bus protocol. And making use of the serial port communication technology to communicate with the host computer, the system achieves the function of remote temperature storage, historical data show and the temperature waveform display.

  14. In-use fuel economy of hybrid-electric school buses in Iowa.

    Science.gov (United States)

    Hallmark, Shauna; Sperry, Bob; Mudgal, Abhisek

    2011-05-01

    Although it is much safer and more fuel-efficient to transport children to school in buses than in private vehicles, school buses in the United States still consume 822 million gal of diesel fuel annually, and school transportation costs can account for a significant portion of resource-constrained school district budgets. Additionally, children in diesel-powered school buses may be exposed to higher levels of particulates and other pollutants than children in cars. One solution to emission and fuel concerns is use of hybrid-electric school buses, which have the potential to reduce emissions and overall lifecycle costs compared with conventional diesel buses. Hybrid-electric technologies are available in the passenger vehicle market as well as the transit bus market and have a track record indicating fuel economy and emissions benefits. This paper summarizes the results of an in-use fuel economy evaluation for two plug-in hybrid school buses deployed in two different school districts in Iowa. Each school district selected a control bus with a route similar to that of the hybrid bus. Odometer readings, fuel consumption, and maintenance needs were recorded for each bus. The buses were deployed in 2008 and data were collected through May 2010. Fuel consumption was calculated for each school district. In Nevada, IA, the overall average fuel economy was 8.23 mpg for the hybrid and 6.35 mpg for the control bus. In Sigourney, IA, the overall average fuel economy was 8.94 mpg for the hybrid and 6.42 mpg for the control bus. The fuel consumption data were compared for the hybrid and control buses using a Wilcoxon signed rank test. Results indicate that fuel economy for the Nevada hybrid bus was 29.6% better than for the Nevada control bus, and fuel economy for the Sigourney hybrid bus was 39.2% higher than for the Sigourney control bus. Both differences were statistically significant.

  15. School bus’s level of service in Malang City

    Science.gov (United States)

    Hariyani, S.

    2017-06-01

    School Bus began operated on the 12th of January 2015. Provision of school buses is expected to reduce not only the use of vehicles by students, but it is also to reduce the number of traffic jams. Malang school bus facilities provided by the Department of Transport in cooperation with the Department of Education to serve students in elementary school, junior and senior high schools. After the service running two years, based on the preliminary observation not all students are interested in using the school bus. The research objective was to measure the school bus’s level service. The method to measure school bus’s level of service was used Importance Performance analysis (IPA). The results showed that through IPA, it can be concluded that school bus’s level of service in Malang City have been able to serve students/customers with the mean of degree suitability (Tki) is 111. Meanwhile it must be observed and get more attention to improve by government, attributes which is lies in the first quadrant or concentrate here (attribute Adequate space, Seating capacity, Availability trash can, Passenger facility down in points, The availability of information boards in each bus stop, Availability public telephone in each bus stop, and Availability CCTV in each bus), in order to increase its performance.

  16. Managing Food Allergies at School: School Transportation Staff

    Centers for Disease Control (CDC) Podcasts

    2015-01-20

    This podcast highlights the role of bus drivers and transportation staff in the management of food allergies in schools. It also identifies CDC food allergy resources for schools.  Created: 1/20/2015 by National Center for Chronic Disease Prevention and Health Promotion (NCCDPHP).   Date Released: 1/20/2015.

  17. Evaluation of Urban Bus Transport Failure in Gujranwala City of Pakistan

    OpenAIRE

    MUHAMMAD WAQAR ASLAM; ZAHARA BATOOL

    2017-01-01

    This research work has evaluated the performance of urban public bus transport service operating in Gujranwala city of Pakistan. The assessment has been made in terms of financial viability, bus condition, operational performance and user perception. Based on the data requirements, various traffic/transport surveys were conducted including Passenger Boarding and Alighting Survey, Bus Count Survey, Bus Inspection Survey, Illegal Operations Survey and Public Transport User Interview Survey in c...

  18. Active Power Filter DC Bus Voltage Piecewise Reaching Law Variable Structure Control

    OpenAIRE

    Liu, Baolian; Ding, Zujun; Zhao, Huanyu; Jin, Defei

    2014-01-01

    The DC bus voltage stability control is one key technology to ensure that Active Power Filter (APF) operates stably. The external disturbances such as power grid and load fluctuation and the system parameters changing may affect the stability of APF DC bus voltage and the normal operation of APF. The mathematical model of DC bus voltage is established according to power balance principle and a DC bus voltage piecewise reaching law variable structure control algorithm is proposed to solve the ...

  19. Kajian Keamanan Pengoperasian Public Transport Tinjauan Terhadap Kekuatan Rangka Body Bus

    OpenAIRE

    Sudiro, B. M

    2010-01-01

    In order to meet the safety and security of the public transportation, design specification of construction body bus or bus frame structures should have an appropriate structural strength and comply with standard design including the safety factor and selection of material besides static and dynamic testing of the part of body bus. It is also realized that a bus carrying passengers have to give secure to the passengers also driver.The fact that a technology concerning with metal works indus...

  20. Developing a viable electric bus service: the Milton Keynes demonstration project

    OpenAIRE

    Miles, John; Potter, Stephen

    2014-01-01

    Buses can be a serious source of city centre air pollution. Electric buses deliver zero emissions but, because of the time required to recharge, more buses are needed for a given timetable than diesel counterparts, so making mainstream electric bus operations prohibitively expensive.\\ud \\ud Early 2014 saw the implementation in Milton Keynes of an electric bus service designed to overcome this problem. An entire bus route has been converted to electric operation with inductive charging at bus ...

  1. DETERMINATION OF THE DELAY DEPARTURE TIME OF THE BUS FROM STOPPING POINT INTO THE CAR FLOW

    Directory of Open Access Journals (Sweden)

    P. Gorbachov

    2014-10-01

    Full Text Available An analytical model for estimation of the bus departure delax from the bus stopping point after passenger loading is presented. The model allows to take into account the traffic density on a particular road section of the transport network, as well as the bus parameters.

  2. Computer-Based Video Instruction to Teach Students with Intellectual Disabilities to Use Public Bus Transportation

    Science.gov (United States)

    Mechling, Linda; O'Brien, Eileen

    2010-01-01

    This study investigated the effectiveness of computer-based video instruction (CBVI) to teach three young adults with moderate intellectual disabilities to push a "request to stop bus signal" and exit a city bus in response to target landmarks. A multiple probe design across three students and one bus route was used to evaluate effectiveness of…

  3. Influences of motorcycle rider and driver characteristics and road environment on red light running behavior at signalized intersections.

    Science.gov (United States)

    Jensupakarn, Auearree; Kanitpong, Kunnawee

    2018-04-01

    In Thailand, red light running is considered as one of the most dangerous behaviors at intersection. Red light running (RLR) behavior is the failure to obey the traffic control signal. However, motorcycle riders and car drivers who are running through red lights could be influenced by human factors or road environment at intersection. RLR could be advertent or inadvertent behavior influenced by many factors. Little research study has been done to evaluate the contributing factors influencing the red-light violation behavior. This study aims to determine the factors influencing the red light running behavior including human characteristics, physical condition of intersection, traffic signal operation, and traffic condition. A total of 92 intersections were observed in Chiang Mai, Nakhon Ratchasima, and Chonburi, the major provinces in each region of Thailand. In addition, the socio-economic characteristics of red light runners were obtained from self-reported questionnaire survey. The Binary Logistic Regression and the Multiple Linear Regression models were used to determine the characteristics of red light runners and the factors influencing rates of red light running respectively. The results from this study can help to understand the characteristics of red light runners and factors affecting them to run red lights. For motorcycle riders and car drivers, age, gender, occupation, driving license, helmet/seatbelt use, and the probability to be penalized when running the red light significantly affect RLR behavior. In addition, the results indicated that vehicle travelling direction, time of day, existence of turning lane, number of lanes, lane width, intersection sight distance, type of traffic signal pole, type of traffic signal operation, length of yellow time interval, approaching speed, distance from intersection warning sign to stop line, and pavement roughness significantly affect RLR rates. Copyright © 2018 Elsevier Ltd. All rights reserved.

  4. Old-Fashioned Bus Trips: New Age Professional Development

    Science.gov (United States)

    Feldhues, Katherine; Epley, Hannah K.

    2018-01-01

    Two 4-H Camp-related bus tours offered new nontraditional professional development (PD) experiences that better align Extension's PD opportunities with the organization's experiential education pedagogy. Creating quality PD opportunities for employees is important because such experiences can affect overall work performance, community connections,…

  5. Analyzing injury severity of bus passengers with different movements.

    Science.gov (United States)

    Li, Duo; Zhao, Yifei; Bai, Qiang; Zhou, Bei; Ling, Hongbiao

    2017-07-04

    Though public transport vehicles are rarely involved in mass casualty accidents, when they are, the number of injuries and fatalities is usually high due to the high passenger capacity. Of the few studies that have been conducted on bus safety, the majority focused on vehicle safety features, road environmental factors, as well as driver characteristics. Nevertheless, few studies have attempted to investigate the underlying risk factors related to bus occupants. This article presents an investigation aimed at identifying the risk factors affecting injury severity of bus passengers with different movements. Three different passenger movement types including standing, seated, and boarding/alighting were analyzed individually using classification and regression tree (CART) method based on publicly available accident database of Great Britain. According to the results of exploratory analyses, passenger age and vehicle maneuver are associated with passenger injury severity in all 3 types of accidents. Moreover, the variable "skidding and overturning" is associated with injury severity of seated passengers and driver age is correlated with injury severity of standing and boarding/alighting passengers. The CART method shows its ability to identify and easily explain the complicated patterns affecting passenger injury severity. Several countermeasures to reduce bus passenger injury severity are recommended.

  6. 49 CFR 374.317 - Identification-bus and driver.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false Identification-bus and driver. 374.317 Section 374... SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS PASSENGER CARRIER REGULATIONS Adequacy of Intercity Motor Common Carrier Passenger Service § 374.317 Identification...

  7. A Quantitative Economics Of Seasonality In Bus Patronage In Nigeria

    African Journals Online (AJOL)

    Seasonal variation is a well-known phenomenon, in many endeavrous and enterprises. Passenger of patronage of road transportation by bus is generally implicated as exhibiting excessive seasonality. The study thus set out to empirically investigate the myth or reality of the thesis that trip generation and trip attraction can ...

  8. Aerodynamic study of state transport bus using computational fluid dynamics

    Science.gov (United States)

    Kanekar, Siddhesh; Thakre, Prashant; Rajkumar, E.

    2017-11-01

    The main purpose of this study was to develop the aerodynamic study of a Maharashtra state road transport bus. The rising fuel price and strict government regulations makes the road transport uneconomical now days. With the objective of increasing fuel efficiency and reducing the emission of harmful exhaust gases. It has been proven experimentally that vehicle consumes almost 40% of the available useful engine power to overcome the drag resistance. This provides us a huge scope to study the influence of aerodynamic drag. The initial of the project was to identify the drag coefficient of the existing ordinary type model called “Parivartan” from ANSYS fluent. After preliminary analysis of the existing model corresponding changes are made in such a way that their implementation should be possible at workshop level. The simulation of the air flow over the bus was performed in two steps: design on SolidWorks CAD and ANSYS (FLUENT) is used as a virtual analysis tool to estimate the drag coefficient of the bus. We have used the turbulence models k-ε Realizable having a better approximation of the actual result. Around 28% improvement in the drag coefficient is achieved by CFD driven changes in the bus design. Coefficient of drag is improved by 28% and fuel efficiency increased by 20% by CFD driven changes.

  9. Staying Safe in the Car and on the Bus

    Science.gov (United States)

    ... a booster! Get in the Back Here's another important safety rule: Sit in the back seat. Kids 12 ... or band concerts once in a while, it's important to follow these rules. When you see the bus driving up, everyone waiting should get into a line. ...

  10. Bus-oriented digital control techniques in nuclear power plants

    International Nuclear Information System (INIS)

    Salm, M.

    1987-01-01

    The author states the conservative principles which govern the authorization procedures for nuclear reactor control systems. Using the example of a feedwater supply regulator, employing a digital, bus-oriented control system, he describes how the stigma attached to the word nuclear can be alleviated. (G.T.H.)

  11. Energy efficient motion control of the electric bus on route

    Science.gov (United States)

    Kotiev, G. O.; Butarovich, D. O.; Kositsyn, B. B.

    2018-02-01

    At present, the urgent problem is the reduction of energy costs of urban motor transport. The article proposes a method of solving this problem by developing an energy-efficient law governing the movement of an electric bus along a city route. To solve this problem, an algorithm is developed based on the dynamic programming method. The proposed method allows you to take into account the constraints imposed on the phase coordinates, control action, as well as on the time of the route. In the course of solving the problem, the model of rectilinear motion of an electric bus on a horizontal reference surface is considered, taking into account the assumptions that allow it to be adapted for the implementation of the method. For the formation of a control action in the equations of motion dynamics, an algorithm for changing the traction / braking torque on the wheels of an electric bus is considered, depending on the magnitude of the control parameter and the speed of motion. An optimal phase trajectory was obtained on a selected section of the road for the prototype of an electric bus. The article presents the comparison of simulation results obtained with the optimal energy efficient control law with the results obtained by a test driver. The comparison proved feasibility of the energy efficient control law for the automobile city electric transport.

  12. Economic impacts of bus rapid transit in southeast Michigan.

    Science.gov (United States)

    2015-12-01

    In recent years, Bus Rapid Transit (BRT) has generated great interest across the United States. There are more than 20 BRT : systems in existence, and more are in the planning stage (including in Detroit). Within the next few years, BRT will be plann...

  13. Optical bus of centralized relay protection and automation system of ...

    African Journals Online (AJOL)

    The article deals with the system of information collection and transfer from a centralized relay protection and automation system for medium voltage electrical units based on a passive optical bus. The issues of electromagnetic compatibility of technical devices are also considered, and the intensity of electromagnetic ...

  14. A Novel Time Synchronization Method for Dynamic Reconfigurable Bus

    Directory of Open Access Journals (Sweden)

    Zhang Weigong

    2016-01-01

    Full Text Available UM-BUS is a novel dynamically reconfigurable high-speed serial bus for embedded systems. It can achieve fault tolerance by detecting the channel status in real time and reconfigure dynamically at run-time. The bus supports direct interconnections between up to eight master nodes and multiple slave nodes. In order to solve the time synchronization problem among master nodes, this paper proposes a novel time synchronization method, which can meet the requirement of time precision in UM-BUS. In this proposed method, time is firstly broadcasted through time broadcast packets. Then, the transmission delay and time deviations via three handshakes during link self-checking and channel detection can be worked out referring to the IEEE 1588 protocol. Thereby, each node calibrates its own time according to the broadcasted time. The proposed method has been proved to meet the requirement of real-time time synchronization. The experimental results show that the synchronous precision can achieve a bias less than 20 ns.

  15. Bussikontsern Go Bus ihaldab Harjumaa turgu / Signe Kalberg

    Index Scriptorium Estoniae

    Kalberg, Signe, 1959-

    2005-01-01

    AS-i Tarbus ja kaheksa bussiettevõtte ühinemisel moodustati AS Go Bus, ettevõte plaanib veel mitme bussifirma liitmist. Atko Grupi juhatuse esimehe Margo Tomingase, AS Sebe nõukogu esimehe Hugo Osula arvamus. Lisa: Konkurentsiamet hoiab silma peal

  16. Spanish version of Bus Drivers' Job Demands Scale (BDJD-24).

    Science.gov (United States)

    Boada-Grau, Joan; Prizmic-Kuzmica, Aldo-Javier; González-Fernández, Marcos-David; Vigil-Colet, Andreu

    2013-01-01

    Karasek and Theorell's Job Demands-Control Model argues that adverse health-related outcomes, both psychological and physiological, arise from a combination of high job demand and a low level of job control. The objective was to adapt Meijman and Kompier's Bus Drivers' Job Demands Scale (BDJD-24), which enables us to assess the job demands of bus drivers, to Spanish. The final version of the Spanish adaptation was applied to a sample made up of 287 bus drivers living in Spain (80.1% men and 19.9% women), whose average age was 40.44 (SD= 11.78). The results yielded a three-factor structure for the scale used: Time Pressure, Safety, and Passengers. These findings confirm that the Spanish version replicates the factor structure of the original English scale. The reliability of the three subscales was acceptable, ranging from .75 to .84. Furthermore, the subscales were also related to different external correlates and to other scales and showed good convergent and criterion validity. The present instrument can be used to evaluate job demands of bus drivers, as its psychometrics are substantially sound.

  17. Measuring Bus Drivers' Occupational Stress Under Changing Working Conditions

    NARCIS (Netherlands)

    Hlotova, Y.; Cats, O.; Meijer, S.A.

    2014-01-01

    Stress is an immense problem in modern society; approximately half of all occupational illnesses are directly or indirectly related to stress. The work of a bus driver is typically associated with high stress levels that negatively influence individual well-being as well as workforce management. The

  18. Steering characteristic of an articulated bus under quasi steady maneuvering

    Science.gov (United States)

    Ubaidillah, Setiawan, Budi Agus; Aridharma, Airlangga Putra; Lenggana, Bhre Wangsa; Caesar, Bernardus Placenta Previo

    2018-02-01

    Articulated buses have been being preferred as public transportation modes due to their operational capacity. Therefore, passenger safety must be the priority of this public service vehicle. This research focused on the analytical approach of steering characteristics of an articulated bus when it maneuvered steadily. Such turning condition could be referred as a stability parameter of the bus for preliminary handling assessment. The analytical approach employed kinematics relationship between front and rear bodies as well as steering capabilities. The quasi steady model was developed to determine steering parameters such as turning radius, oversteer, and understeer. The mathematical model was useful for determining both coefficients of understeer and oversteer. The dimension of articulated bus followed a commonly used bus as utilized in Trans Jakarta busses. Based on the simulation, for one minimum center of the body, the turning radius was calculated about 8.8 m and 7.6 m at steady turning speed of 10 km/h. In neutral condition, the minimum road radius should be 6.5 m at 10 km/h and 6.9 m at 40 km/h. For two centers of the body and oversteer condition, the front body has the turning radius of 8.8 m, while, the rear body has the turning radius of 9.8 m at both turning speeds of 40 km/h. The other steering parameters were discussed accordingly.

  19. Real life testing of a Hybrid PEM Fuel Cell Bus

    Science.gov (United States)

    Folkesson, Anders; Andersson, Christian; Alvfors, Per; Alaküla, Mats; Overgaard, Lars

    Fuel cells produce low quantities of local emissions, if any, and are therefore one of the most promising alternatives to internal combustion engines as the main power source in future vehicles. It is likely that urban buses will be among the first commercial applications for fuel cells in vehicles. This is due to the fact that urban buses are highly visible for the public, they contribute significantly to air pollution in urban areas, they have small limitations in weight and volume and fuelling is handled via a centralised infrastructure. Results and experiences from real life measurements of energy flows in a Scania Hybrid PEM Fuel Cell Concept Bus are presented in this paper. The tests consist of measurements during several standard duty cycles. The efficiency of the fuel cell system and of the complete vehicle are presented and discussed. The net efficiency of the fuel cell system was approximately 40% and the fuel consumption of the concept bus is between 42 and 48% lower compared to a standard Scania bus. Energy recovery by regenerative braking saves up 28% energy. Bus subsystems such as the pneumatic system for door opening, suspension and brakes, the hydraulic power steering, the 24 V grid, the water pump and the cooling fans consume approximately 7% of the energy in the fuel input or 17% of the net power output from the fuel cell system. The bus was built by a number of companies in a project partly financed by the European Commission's Joule programme. The comprehensive testing is partly financed by the Swedish programme "Den Gröna Bilen" (The Green Car). A 50 kW el fuel cell system is the power source and a high voltage battery pack works as an energy buffer and power booster. The fuel, compressed hydrogen, is stored in two high-pressure stainless steel vessels mounted on the roof of the bus. The bus has a series hybrid electric driveline with wheel hub motors with a maximum power of 100 kW. Hybrid Fuel Cell Buses have a big potential, but there are

  20. THE PREVALENCE OF MUSCULOSKELETAL DISORDERS AMONG BUS DRIVERS IN TRICITY

    Directory of Open Access Journals (Sweden)

    Lalit

    2015-10-01

    Full Text Available Background: Musculoskeletal disorders are widespread in many countries around the world. It has been reported that about 58 percent of the world's population over the age of 10 years spent one third of their life span at work. The population at a high risk include nursing facilities, transportation, mining, food processing, leather tanning, heavy and light manufacturing. Transport workers have been found to be at high risk of developing work related musculoskeletal disorders (WRMSDs. There has been literature evidence regarding the prevalence of musculoskeletal disorders in bus drivers of various cities of different countries. But no study has been done so far in Tricity (Chandigarh, Panchkula and Mohali for the same. The purpose of this study is to investigate the prevalence and characteristics of work related musculoskeletal disorders (WRMSDs among bus drivers of Tricity. Methods: 300 bus drivers were included in the study according to the inclusion and exclusion criteria. The standardized Nordic questionnaire for musculoskeletal disorder and a self administered questionnaire were filled by therapist after the personal interview of each driver. Results: Unpaired t test was used to measure the difference in variable of two groups and Karl Pearson’s correlation coefficient was used to determine the correlation between two entities. In the present study, the subjects were in the age group of 25 to 50 years. Out of the total sample of 300 male bus drivers in Tricity, 159 reported that they had WRMSDs. The prevalence of WRMSDs among bus drivers in Tricity was 53%. In present study, the prevalence of low back pain was highest among the bus drivers that are 30.3%, then neck pain 17.3%, knee pain 14.7%, shoulder 6.3%, ankle and feet 5.7%, upper back 4%, hip and thigh 4%, elbow 1.3% and wrist and hand 1.3%. Thus low back pain, neck pain and knee pain are the most prevalent WRMSDs amongst bus drivers. Conclusions: Work-related biomechanical

  1. Problems of One School Board Attorney.

    Science.gov (United States)

    Fisher, M. Bryon

    The speaker, a school board attorney, outlines four legal problems he has had to deal with. The cases concern teacher dismissal, the district's responsibility in the case of "hazardous transportation," school district purchases for student activities (student photographs), and school bus leasing. (IRT)

  2. Optimal bus temperature for thermal comfort during a cool day.

    Science.gov (United States)

    Velt, K B; Daanen, H A M

    2017-07-01

    A challenge for electric buses is to minimize heating and cooling power to maximally extend the driving range, but still provide sufficient thermal comfort for the driver and passengers. Therefore, we investigated the thermal sensation (TS) and thermal comfort (TC) of passengers in buses during a cool day (temperature 13.4 ± 0.5 °C, relative humidity (RH) 60 ± 5.8%) typical for the Dutch temperate maritime climate. 28 Males and 72 females rated TS and TC and gave information on age, stature, body weight and worn garments. The temperature in the bus of 22.5 ± 1.1 °C and RH of 59.9 ± 5.8% corresponded to a slightly warm feeling (TS = 0.85 ± 1.06) and TC of 0.39 ± 0.65. TS related significantly to bus temperature, clothing insulation and age. Linear regression based on these parameters showed that the temperature in the bus corresponding to TC = 0 and TS = 0 would have been 20.9 ± 0.6 °C. In conclusion, a 1.6 °C lower bus temperature during the investigated cool day probably would have led to less thermal discomfort and energy savings of electrical busses. The methodology to relate climatic measurements to subjective assessments is currently employed in a wider climatic range and may prove to be useful to find a better balance between thermal comfort and energy savings of the bus. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. School transportation mode, by distance between home and school, United States, ConsumerStyles 2012.

    Science.gov (United States)

    Beck, Laurie F; Nguyen, Daniel D

    2017-09-01

    Motor-vehicle crashes are a leading cause of death among children in the United States, and almost one-fourth of all trips by school-aged children are trips to and from school. This study sought to determine how children (5-18years) travel to and from school and, among those living ≤1mile of school, to explore the role of school bus service eligibility on school travel mode. We used national 2012 survey data to determine prevalence of usual school travel mode, stratified by distance from school. For those living ≤1mile of school, multivariable regression was conducted to assess the association between bus service eligibility and walking or bicycling. Almost half (46.6%) of all children rode in passenger vehicles (PV) to school and 41.8% did so for the trip home. Results were similar among those living ≤1mile (48.1%, PV to school; 41.3%, PV to home). Among those living ≤1mile, 21.9% and 28.4% of children walked or bicycled to and from school, respectively. Ineligibility for school bus service was strongly associated with walking or bicycling to school [adjusted prevalence ratio (aPR: 5.36; ppassenger vehicles were a common mode of travel. For children who live close to school, the role that school bus service eligibility plays in walking or bicycling deserves further consideration. Given the large proportion of children who use passenger vehicles for school travel, effective interventions can be adopted to increase proper child restraint and seat belt use and reduce crash risks among teen drivers. Better understanding of conditions under which bus service is offered to children who live close to school could inform efforts to improve pedestrian and bicyclist safety for school travel. Published by Elsevier Ltd.

  4. SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: First Results Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L.; Chandler, K.

    2011-03-01

    This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. This report provides the early data results and implementation experience of the AT fuel cell bus since it was placed in service.

  5. Rancang Bangun Sistem Pemesanan Tiket Bus Kupang-Atambua Berbasis SMS Gateway

    Directory of Open Access Journals (Sweden)

    Emerensiana Ngaga

    2016-11-01

    Full Text Available Bus merupakan alat transportasi yang paling banyak digunakan masyarakat karena harga yang murah dan masih terjangkau untuk masyarakat kalangan ekonomi menengah ke bawah.  Umumnya pemesanan tiket bus dilakukan dengan mendatangi langsung tempat penjualan tiket bus atau dengan cara menelepon ke kantor agen. Proses pemesanan seperti ini  memiliki kekurangan dimana pegawai kerepotan dalam mencatat dan seringkali terjadi kesalahan dalam mencatat pemesanan tiket. Sedangkan untuk waktu pemesanan, umumnya calon penumpang melakukan pemesanan tiket, satu atau dua hari sebelum keberangkatan dan ada juga yang tidak sempat memesan tiket beberapa hari sebelumnya dan melakukan pembelian tiket pada hari keberangkatan sehingga sering kali tidak mendapatkan tiket. Penelitian ini bertujuan merancang bangun sistem pemesanan tiket bus berbasis SMS Gateway yang memberikan kemudahan layanan pemesanan tiket bus bagi masyarakat secara jarak jauh serta kemudahan mengetahui informasi penjadwalan bus dengan cepat. Aplikasi dibangun menggunakan metode Unified Process, dengan bahasa pemrograman Java NetBeansIDE 7.3.1, MySQL sebagai database dan Gammu sebagai software untuk membantu pembangunan aplikasi SMS Gateway. Hasil dari penelitian ini adalah sebuah sistem pemesanan tiket bus yang memberikan alternatif baru proses pemesanan tiket bus secara baik tanpa ada permasalahan jarak dan waktu. Selain itu masyarakat juga dapat mengetahui informasi jadwal bus, harga tiket dan juga informasi bila terjadi perubahan jadwal keberangkatan bus.   Kata kunci— Bus, Tiket, SMS Gateway, Unified Process

  6. Does the rider influence the horse's movement in hippotherapy? [Ovlivňuje jezdec pohyb koně v hipoterapii?

    Directory of Open Access Journals (Sweden)

    Miroslav Janura

    2011-12-01

    Full Text Available BACKGROUND: In hippotherapy, in comparison to equitation, it is assumed that the rider is a passive element, only stimulated by mechanical impulses produced by the moving horse's back. OBJECTIVE: The aim of the study was to determine the influence of the rider on the horse's movement in hippotherapy. METHODS: Two sound thoroughbreds with a similar body shape and size (age: 19 and 14 years, withers height: 1.65 m both, weight: 548 and 500 kg participated in the study. The test group of riders consisted of twelve healthy young women (age: 23.3 ± 2.8, weight: 59.2 ± 5.3, height: 167.3 ± 4.2 without any previous horse riding experience. For each rider 36 trials in total (6 strides in 6 hippotherapy sessions held during the course of five weeks were evaluated. The movement was recorded by 4 videocameras (frequency 50 Hz. Spatiotemporal variables, the vertical displacement of selected points on the horse's limbs and the back and angle displacement of tarsus joint were analyzed by the APAS programme. Statistical processing was performed by the Statistica programme (one way ANOVA. RESULTS: In our study, we didn't find any statistically significant difference (p CONCLUSIONS: In hippotherapy, basic spatiotemporal variables of a horse's natural walking aren't influenced by the rider. As for the vertical displacement of points on the limbs and the horse's back, the results are not explicit. A larger number of horses is necessary for future study. The patient and the horse in hippotherapy are to be rather considered as interactive elements than as passive and active elements.[VÝCHODISKA: V hipoterapii je, na rozdíl od jezdectví, jezdec považován za pasivní prvek, který je stimulován impulsy, které vycházejí z pohybujícího se hřbetu koně. CÍLE: Cílem studie bylo zjistit, zda jezdec ovlivňuje pohyb koně v hipoterapii. METODIKA: Do studie byli zařazeni dva angličtí plnokrevníci podobné tělesné konstituce (věk: 19 a 14 let, v

  7. American Fuel Cell Bus Project Evaluation: Third Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jeffers, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2017-05-01

    This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses operating in the Coachella Valley area of California. The prototype AFCB, which was developed as part of the Federal Transit Administration's (FTA) National Fuel Cell Bus Program, was delivered to SunLine in November 2011 and was put in revenue service in mid-December 2011. Two new AFCBs with an upgraded design were delivered in June/July of 2014 and a third new AFCB was delivered in February 2015. FTA and the AFCB project team are collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory to evaluate the buses in revenue service. This report covers the performance of the AFCBs from July 2015 through December 2016.

  8. Discharging a DC bus capacitor of an electrical converter system

    Science.gov (United States)

    Kajouke, Lateef A; Perisic, Milun; Ransom, Ray M

    2014-10-14

    A system and method of discharging a bus capacitor of a bidirectional matrix converter of a vehicle are presented here. The method begins by electrically shorting the AC interface of the converter after an AC energy source is disconnected from the AC interface. The method continues by arranging a plurality of switching elements of a second energy conversion module into a discharge configuration to establish an electrical current path from a first terminal of an isolation module, through an inductive element, and to a second terminal of the isolation module. The method also modulates a plurality of switching elements of a first energy conversion module, while maintaining the discharge configuration of the second energy conversion module, to at least partially discharge a DC bus capacitor.

  9. Distributed cooperative synchronization strategy for multi-bus microgrids

    DEFF Research Database (Denmark)

    Sun, Yao; Zhong, Chaolu; Hou, Xiaochao

    2017-01-01

    Microgrids can operate in both grid-connected mode and islanded mode. In order to smooth transfer from islanded mode to grid-connected mode, it is necessary to synchronize the point of common coupling (PCC) with main utility grid (UG) in voltage frequency, phase and amplitude. Conventional...... synchronization methods based on centralized communication are very costly and not suitable for multi-bus microgrids that have a large number of distributed generators (DGs). To address this concern, this study presents an active synchronization control strategy based on distributed cooperation technology...... for multi-bus microgrids. The proposed method can reconnect the microgrid in island to UG seamlessly with sparse communication channels. Synchronization correction signals are generated by a voltage controller, which are only transmitted to the leader DGs. Meanwhile, each DG exchanges information with its...

  10. Foundation field bus in the Spanish nuclear sector

    International Nuclear Information System (INIS)

    Saez de Montagut Revenga, G.

    2013-01-01

    This paper deals with the modification made in power plants nuclear ASCO 1 and 2 in which scans is the level Control system of Heaters to implementing an Ovation system, as well as the standard Foundation Field bus for field communications. This digitalisation has required a detailed study of the implications on security that could have the centralization of control loops in main feedwater system.

  11. BC Transit Fuel Cell Bus Project: Evaluation Results Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, M. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2014-02-01

    This report evaluates a fuel cell electric bus demonstration led by British Columbia Transit (BC Transit) in Whistler, Canada. BC Transit is collaborating with the California Air Resources Board and the U.S. Department of Energy's National Renewable Energy Laboratory to evaluate the buses in revenue service. This evaluation report covers two years of revenue service data on the buses from April 2011 through March 2013.

  12. The Designing Bus for Nuclear Safety Class Controller

    International Nuclear Information System (INIS)

    Lee, Dongil; Lee, Myeongkyun; Yun, Donghwa; Ryoo, Kwangki

    2013-01-01

    EtherCAT (Ethernet for Control Automation Technology) is based on the IEEE 802.3 standard as one of the communication which is the I/O (Input/Output), sensors and communication function of PLC (Programmable Logic Controller) in industry and factory environment use is increasing. The Nuclear Safety Class Controller implemented by the EtherCAT applied bus can be shown the improving performance of data transmission in the controller

  13. Deregulation and Intercity Bus Operations in Florida: A Preliminary Study.

    Science.gov (United States)

    1981-03-02

    revenues have been consistent recently, but expenses have risen. The three areas most frequently served by Rabbit Bus Lines are Disney World, Sea World...Manager, Shoreline Stages had annual revenues of roughly $890,000 in 1980. In terms of trips, about ninety percent of this carrier’s traffic is interstate...this traffic constitutes the bulk of Shoreline Stage’s business by revenue , volume of traffic, and number of passengers. Charter trips to Disney

  14. Parallel data grabbing card based on PCI bus RS422

    International Nuclear Information System (INIS)

    Zhang Zhenghui; Shen Ji; Wei Dongshan; Chen Ziyu

    2005-01-01

    This article briefly introduces the developments of the parallel data grabbing card based on RS422 and PCI bus. It could be applied for grabbing the 14 bits parallel data in high speed, coming from the devices with RS422 interface. The methods of data acquisition which bases on the PCI protocol, the functions and their usages of the chips employed, the ideas and principles of the hardware and software designing are presented. (authors)

  15. The Designing Bus for Nuclear Safety Class Controller

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dongil; Lee, Myeongkyun; Yun, Donghwa [PONUTech Co,. Ltd., Research Institute, Ulsan (Korea, Republic of); Ryoo, Kwangki [Hanbat National Univ., Daejeon (Korea, Republic of)

    2013-10-15

    EtherCAT (Ethernet for Control Automation Technology) is based on the IEEE 802.3 standard as one of the communication which is the I/O (Input/Output), sensors and communication function of PLC (Programmable Logic Controller) in industry and factory environment use is increasing. The Nuclear Safety Class Controller implemented by the EtherCAT applied bus can be shown the improving performance of data transmission in the controller.

  16. Low back trouble among urban bus drivers in Denmark

    DEFF Research Database (Denmark)

    Netterstrøm, Bo; Juel, K

    1989-01-01

    herniation was 137 compared to all Danish men. These differences were statistically significant. Of psychosocial factors only "the feeling of being mentally unbalanced" was found to be statistically significantly related to subsequent hospital discharge with a LBT-diagnosis. Long seniority as bus driver...... of those discharged from hospital with LBT makes it probable that LBT has etiologic factors in the work environment. The sedentary position and whole-body vibrations may be contributory causes....

  17. A counting-card circuit based on PCI bus

    International Nuclear Information System (INIS)

    Shi Jing; Li Yong; Chinese Academy of Sciences, Lanzhou; Su Hong; Dong Chengfu; Li Xiaogang; Ma Xiaoli

    2004-01-01

    A counting-card circuit based on PCI bus that we developed recently used for advanced personal computer will be introduced in this paper briefly. The maximum count capacity of this counting-card is 10 9 -1, ranging from 0 to 999 999 999, the maximum counting time range, 1 x 10 6 s, can be set in 1 cycle, the maximum counting rate is 20 MHz for positive input. (authors)

  18. Oxidative and nitrosative stress markers in bus drivers

    Czech Academy of Sciences Publication Activity Database

    Rössner ml., Pavel; Švecová, Vlasta; Milcová, Alena; Lněničková, Zdena; Solanský, I.; Santella, R. M.; Šrám, Radim

    2007-01-01

    Roč. 617, - (2007), s. 23-32 ISSN 0027-5107 R&D Projects: GA MŽP SL/5/160/05; GA AV ČR 1QS500390506 Institutional research plan: CEZ:AV0Z50390512 Keywords : oxidative stress * bus drivers * air pollution Subject RIV: DN - Health Impact of the Environment Quality Impact factor: 4.159, year: 2007

  19. Multi drop bus controller for IBM PC/AT

    International Nuclear Information System (INIS)

    Bardik, Yu.I.; Kalistratov, E.N.; Matyushin, A.A.; Obukhov, G.A.; Trofimov, N.N.

    1993-01-01

    The module PC-AT-PBC gives a possibility to create a working place based on the computer IBM PC/AT for testing of hardware which is compatible with the multi drop bus. The KP1830BE31 micro program change turns the module into timing generator for power supply controllers of the UNK correction system. The structure of the module, functional parts, library functions and two application programs have been described. 4 refs., 9 figs

  20. Definition and Evaluation of Bus and Truck Automation Operations Concepts

    OpenAIRE

    Tsao, H.-S. Jacob; Botha, Jan L.

    2002-01-01

    Traffic congestion will continue to worsen and likely worsen at a faster rate than ever. People throughput and freight throughput have become critical issues for California and the rest of the nation. PATH has been funding a one-year research project entitled "Definition and Evaluation of Bus and Truck Automation Operations Concepts," proposed by the authors. This report summarizes the results of the research project achieved during the first six months. During those six months, we reviewed l...

  1. Evaluation of Bus Vibration Comfort Based on Passenger Crowdsourcing Mode

    Directory of Open Access Journals (Sweden)

    Hong Zhao

    2016-01-01

    Full Text Available Vibration comfort is an important factor affecting the quality of service (QoS of bus. In order to make people involved in supervising bus’s vibration comfort and improve passengers’ riding experience, a novel mode of passenger crowdsourcing is introduced. In this paper, comfort degree of bus vibration is calculated from bus’s vibration signals collected by passengers’ smartphones and sent through WiFi to the Boa web server which shows the vibration comfort on the LCD deployed in bus and maybe trigger alarm lamp when the vibration is beyond the threshold. Three challenges here have been overcome: firstly, space coordinate transformation algorithm is used to solve the constant drift of signals collected; secondly, a low-pass filter is designed to isolate gravity from signals real-timely via limited computing resources; thirdly, an embedded evaluation system is developed according to the calculation procedure specified by criterion ISO 2631-1997. Meanwhile, the model proposed is tested in a practical running environment, the vibration data in whole travel are recorded and analyzed offline. The results show that comfort degree of vibration obtained from the experimental system is identical with the truth, and this mode is proved to be effective.

  2. HEV Test Bench Based on CAN Bus Sensor Communication

    Directory of Open Access Journals (Sweden)

    Shupeng ZHAO

    2014-02-01

    Full Text Available The HEV test bench based on Controller Area Network bus was studied and developed. Control system of HEV power test bench used the CAN bus technology. The application of CAN bus technology on control system development has opened up a new research direction for domestic automobile experimental platform. The HEV power control system development work was completed, including power master controller, electric throttle controller, driving simulation platform, CAN2.0 B communication protocol procedures for formulation, CAN communication monitoring system, the simulation model based on MATLAB code automatic generation technology research, etc. Maximum absorption power of the test bench is 90 kW, the test bench top speed is 6000 r/min, the CAN communication data baud rate is 10~500 k, the conventional electric measurement parameter part precision satisfies the requirement of development of HEV. On the HEV test bench the result of regenerative braking experiment shows that the result got by the test bench was closer to the results got by outdoor road test. And the fuel consumption experiment test results show that the HEV fuel consumption and the charge-discharge character are in linear relationship. The establishment of the test platform for the evaluation of the development of hybrid electric vehicle and power provides physical simulation and test platform.

  3. Electric bus migration in Bengaluru with dynamic charging technologies

    Directory of Open Access Journals (Sweden)

    Ankit Kumar Begwani

    2017-12-01

    Full Text Available Rapid but unplanned urban development coupled with economic growth has resulted in congestion and pollution concerns in Indian cities. This forced India consider taking concrete steps towards design policies that would help stir the nation towards a more sustainable future. India, along with other bigger Asian economies like China, needs to address the growing global concerns over climate change and design their framework and policies to help cut down the greenhouse gas emissions. Transportation is a major source of pollution. A shift towards a pro-public transport policy would solve the traffic congestion problems and address the emission concerns. India has a significantly higher modal share of public transportation in its major cities. Public bus transport system acts as a lifeline to the India’s poor and middle class citizens. The following study focuses on the need for a replacement of conventional fossil fuel dependent buses with Electric buses in the existing public transport bus fleet in the city of Bengaluru. A design has been developed to utilize wireless charging technologies to realize electric bus migration in Bengaluru.

  4. Pilot survey of subway and bus stop noise levels.

    Science.gov (United States)

    Gershon, Robyn R M; Neitzel, Richard; Barrera, Marissa A; Akram, Muhammad

    2006-09-01

    Excessive noise exposure is a serious global urban health problem, adversely affecting millions of people. One often cited source of urban noise is mass transit, particularly subway systems. As a first step in determining risk within this context, we recently conducted an environmental survey of noise levels of the New York City transit system. Over 90 noise measurements were made using a sound level meter. Average and maximum noise levels were measured on subway platforms, and maximum levels were measured inside subway cars and at several bus stops for comparison purposes. The average noise level measured on the subway platforms was 86 +/- 4 dBA (decibel-A weighting). Maximum levels of 106, 112, and 89 dBA were measured on subway platforms, inside subway cars, and at bus stops, respectively. These results indicate that noise levels in subway and bus stop environments have the potential to exceed recommended exposure guidelines from the World Health Organization (WHO) and U.S. Environmental Protection Agency (EPA), given sufficient exposure duration. Risk reduction strategies following the standard hierarchy of control measures should be applied, where feasible, to reduce subway noise exposure.

  5. Replacement model of city bus: A dynamic programming approach

    Science.gov (United States)

    Arifin, Dadang; Yusuf, Edhi

    2017-06-01

    This paper aims to develop a replacement model of city bus vehicles operated in Bandung City. This study is driven from real cases encountered by the Damri Company in the efforts to improve services to the public. The replacement model propounds two policy alternatives: First, to maintain or keep the vehicles, and second is to replace them with new ones taking into account operating costs, revenue, salvage value, and acquisition cost of a new vehicle. A deterministic dynamic programming approach is used to solve the model. The optimization process was heuristically executed using empirical data of Perum Damri. The output of the model is to determine the replacement schedule and the best policy if the vehicle has passed the economic life. Based on the results, the technical life of the bus is approximately 20 years old, while the economic life is an average of 9 (nine) years. It means that after the bus is operated for 9 (nine) years, managers should consider the policy of rejuvenation.

  6. Safety evaluation of a hydrogen fueled transit bus

    Energy Technology Data Exchange (ETDEWEB)

    Coutts, D.A.; Thomas, J.K.; Hovis, G.L.; Wu, T.T. [Westinghouse Savannah River Co., Aiken, SC (United States)

    1997-12-31

    Hydrogen fueled vehicle demonstration projects must satisfy management and regulator safety expectations. This is often accomplished using hazard and safety analyses. Such an analysis has been completed to evaluate the safety of the H2Fuel bus to be operated in Augusta, Georgia. The evaluation methods and criteria used reflect the Department of Energy`s graded approach for qualifying and documenting nuclear and chemical facility safety. The work focused on the storage and distribution of hydrogen as the bus motor fuel with emphases on the technical and operational aspects of using metal hydride beds to store hydrogen. The safety evaluation demonstrated that the operation of the H2Fuel bus represents a moderate risk. This is the same risk level determined for operation of conventionally powered transit buses in the United States. By the same criteria, private passenger automobile travel in the United States is considered a high risk. The evaluation also identified several design and operational modifications that resulted in improved safety, operability, and reliability. The hazard assessment methodology used in this project has widespread applicability to other innovative operations and systems, and the techniques can serve as a template for other similar projects.

  7. Violence against metropolitan bus drivers and fare collectors in Brazil

    Directory of Open Access Journals (Sweden)

    Ada Ávila Assunção

    2015-01-01

    Full Text Available OBJECTIVE To analyze the correlation between sociodemographic factors and working conditions of bus workers in a metropolitan area and violence against them. METHODS This cross-sectional study used a nonprobabilistic sample estimated according to the number of workers employed in bus companies located in three cities in the Belo Horizonte metropolitan region in 2012 (N = 17,470. Face-to-face interviews were conducted using a digital questionnaire. The factors associated with violence were analyzed in two stages using Poisson regression, according to each level. The magnitude of the association was evaluated using prevalence ratios with robust variance and a statistical significance of 5%, and 95% confidence intervals were obtained. RESULTS The study sample comprised 782 drivers and 691 fare collectors; 45.0% participants reported at least one act of violence in the workplace in the last 12 months, with passengers being predominantly responsible. The age of the bus workers was inversely associated with violence. Chronic diseases, sickness absenteeism, and working conditions were also associated with violence. CONCLUSIONS The findings on the correlation between violence and working conditions are essential for implementing prevention strategies by transportation service managers.

  8. An Optimization Model for the Selection of Bus-Only Lanes in a City.

    Science.gov (United States)

    Chen, Qun

    2015-01-01

    The planning of urban bus-only lane networks is an important measure to improve bus service and bus priority. To determine the effective arrangement of bus-only lanes, a bi-level programming model for urban bus lane layout is developed in this study that considers accessibility and budget constraints. The goal of the upper-level model is to minimize the total travel time, and the lower-level model is a capacity-constrained traffic assignment model that describes the passenger flow assignment on bus lines, in which the priority sequence of the transfer times is reflected in the passengers' route-choice behaviors. Using the proposed bi-level programming model, optimal bus lines are selected from a set of candidate bus lines; thus, the corresponding bus lane network on which the selected bus lines run is determined. The solution method using a genetic algorithm in the bi-level programming model is developed, and two numerical examples are investigated to demonstrate the efficacy of the proposed model.

  9. An Optimization Model for the Selection of Bus-Only Lanes in a City.

    Directory of Open Access Journals (Sweden)

    Qun Chen

    Full Text Available The planning of urban bus-only lane networks is an important measure to improve bus service and bus priority. To determine the effective arrangement of bus-only lanes, a bi-level programming model for urban bus lane layout is developed in this study that considers accessibility and budget constraints. The goal of the upper-level model is to minimize the total travel time, and the lower-level model is a capacity-constrained traffic assignment model that describes the passenger flow assignment on bus lines, in which the priority sequence of the transfer times is reflected in the passengers' route-choice behaviors. Using the proposed bi-level programming model, optimal bus lines are selected from a set of candidate bus lines; thus, the corresponding bus lane network on which the selected bus lines run is determined. The solution method using a genetic algorithm in the bi-level programming model is developed, and two numerical examples are investigated to demonstrate the efficacy of the proposed model.

  10. Cellular Automata Based Modeling for Evaluating Different Bus Stop Designs in China

    Directory of Open Access Journals (Sweden)

    Haoyang Ding

    2015-01-01

    Full Text Available A cellular automaton model is proposed to simulate mixed traffic flow composed of motor vehicles and bicycles near bus stops. Three typical types of bus stops which are common in China are considered in the model, including two types of curbside bus stops and one type of bus bay stops. Passenger transport capacity of three types of bus stops, which is applied to evaluate the bus stop design, is calculated based on the corresponding traffic flow rate. According to the simulation results, the flow rates of both motor vehicles and bicycles exhibit phase transition from free flow to the saturation one at the critical point. The results also show that the larger the interaction between motor vehicle and bicycle flow is near curbside bus stops, the more the value of saturated flows drops. Curbside bus stops are more suitable when the conflicts between two flows are small and the inflow rate of motor vehicles is low. On the contrary, bus bay stops should be applied due to their ability to reduce traffic conflicts. Findings of this study can provide useful suggestions on bus stop selection considering different inflow rate of motor vehicles and bicycles simultaneously.

  11. Working conditions of bus drivers in the private sector and bus crashes in Kandy district, Sri Lanka: a case-control study.

    Science.gov (United States)

    Jayatilleke, A U; Nakahara, S; Dharmaratne, S D; Jayatilleke, A C; Poudel, K C; Jimba, M

    2009-04-01

    To explore the effects of working conditions of private-bus drivers on bus crashes in Kandy district, Sri Lanka. A case-control study was carried out from August to September 2006. All private-bus drivers registered in Kandy district and involved in crashes reported to the police between November 2005 and April 2006 (n = 63) were selected as cases. Two control groups were included: private-bus drivers working on the same routes as the case drivers (n = 90) and private-bus drivers selected randomly from other routes of the district (n = 111). Data were collected using an anonymous self-administered questionnaire. Associations between working conditions and crashes were analysed using logistic regression. A strong association was observed between drivers' disagreements about working hours and bus crashes (matched controls, adjusted odds ratio (AOR) 5.98, 95% CI 1.02 to 34.90; unmatched controls, AOR 18.74, 95% CI 2.00 to 175.84). A significant association was also observed between low salaries (US$100) and private-bus crashes (matched controls, AOR 1.01, 95% CI 0.40 to 2.54; unmatched controls, AOR 3.09, 95% CI 1.26 to 7.57). Drivers' disagreements about working hours and low salaries were significant risk factors for private-bus crashes in Kandy district, Sri Lanka. Therefore, new legislation for private-bus owners on the working hours and salaries of their drivers to prevent private-bus crashes is recommended.

  12. Life cycle cost analysis of a car, a city bus and an intercity bus powertrain for year 2005 and 2020

    International Nuclear Information System (INIS)

    Hellgren, Jonas

    2007-01-01

    The international economy, in the beginning of the 20th century, is characterized by uncertainty about the supply and the price of oil. Together with the fast decrease of electrical propulsion component prices, it becomes more and more cost effective to develop vehicles with alternative powertrains. This paper focuses on two questions: Are alternative powertrains especially cost effective for specific applications?; How does an increased fossil fuel price influences the choose of powertrain? To assess these questions, a computer tool named THEPS, developed in a Ph.D. project, is used. Three applications and three scenarios are analysed. The applications, a car, a city bus and an intercity bus, are vehicles all assumed to operate in Sweden. One scenario represents year 2005, the other two year 2020. The two future scenarios are characterized by different fossil fuel prices. The study, presented in the paper, indicates that alternative powertrains can be competitive from a cost perspective, in some applications, already in year 2005. It is for example cost effective to equip a city bus, running in countries with a high fuel price, with a hybrid powertrain. The study also indicates that pure electric, hybrid and/or fuel cell cars will probably be a more cost effective choice than conventional cars in year 2020. Another indication is that it will not be clear which powertrain concept to choose. The reason is that many cost effective powertrain concepts will be offered. The best choice will depend on the application

  13. A PRACTICAL STUDY ON APPLICABILITY OF THE INCENTIVE SUBSIDY TO BUS NETWORK IN KUMAMOTO CITY

    Science.gov (United States)

    Mizokami, Shoshi; Fujimi, Toshio; Hirano, Toshihiko

    Recently, the number of passenger of public bus services in Japan tends to decrease due to the motorization. This condition leads to a severe management situation, including in Kumamoto City. Since 1984, the deficit of bus companies operation in provision of bus services in Kumamoto has been covered by Kumamoto City Government on the basis of lines subsidy, and the city allocated a number of subsidy of about 200 million yen in 2007. Currently, The Kumamoto city government plans to reduce the amount of subsidy to bus companies by introducing the giving of incentive to bus companies in order to trim bus company deficit. This study aims to construct the mathematical model of the incentive reward and apply the model to realignment of buses lines networks in Kumamoto Metropolitan Area.

  14. SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Third Results Reports

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L.; Chandler, K.

    2012-05-01

    This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. NREL has previously published two reports documenting the operation of the fuel cell bus in service. This report provides a summary of the results with a focus on the bus operation from July 2011 through January 2012.

  15. SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Fourth Results Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L.; Chandler, K.

    2013-01-01

    SunLine Transit Agency, which provides public transit services to the Coachella Valley area of California, has demonstrated hydrogen and fuel cell bus technologies for more than 10 years. In May 2010, SunLine began demonstrating the advanced technology (AT) fuel cell bus with a hybrid electric propulsion system, fuel cell power system, and lithium-based hybrid batteries. This report describes operations at SunLine for the AT fuel cell bus and five compressed natural gas buses. The U.S. Department of Energy's National Renewable Energy Laboratory (NREL) is working with SunLine to evaluate the bus in real-world service to document the results and help determine the progress toward technology readiness. NREL has previously published three reports documenting the operation of the fuel cell bus in service. This report provides a summary of the results with a focus on the bus operation from February 2012 through November 2012.

  16. MIL-STD-1553 dynamic bus controller/remote terminal hybrid set

    Science.gov (United States)

    Friedman, S. N.

    This paper describes the performance, physical and electrical requirements of a Dual Redundant BUS Interface Unit (BIU) acting as a BUS Controller Interface Unit (BCIU) or Remote Terminal Unit (RTU) between a Motorola 68000 VME BUS and MIL-STD-1553B Multiplex Data Bus. A discussion of how the BIU Hybrid set is programmed, and operates as a BCIU or RTU, will be included. This paper will review Dynamic Bus Control and other Mode Code capabilities. The BIU Hybrid Set interfaces to a 68000 Microprocessor with a VME Bus using programmed I/O transfers. This special interface will be discussed along with the internal Dual Access Memory (4K x 16) used to support the data exchanges between the CPU and the BIU Hybrid Set. The hybrid set's physical size and power requirements will be covered. This includes the present Double Eurocard the BIU function is presently being offered on.

  17. Identification of voltage stability condition of a power system using measurements of bus variables

    Directory of Open Access Journals (Sweden)

    Durlav Hazarika

    2014-12-01

    Full Text Available Several online methods were proposed for investigating the voltage stability condition of an interconnected power system using the measurements of voltage and current phasors at a bus. For this purpose, phasor measurement units (PMUs are used. A PMU is a device which measures the electrical waves on an electrical network, using a common time source (reference bus for synchronisation. This study proposes a method for online monitoring of voltage stability condition of a power system using measurements of bus variables namely – (i real power, (ii reactive power and (iii bus voltage magnitude at a bus. The measurements of real power, reactive power and bus voltage magnitude could be extracted/captured from a smart energy meter. The financial involvement for implementation of the proposed method would significantly lower compared with the PMU-based method.

  18. Bitmap-Wise Wireless M-Bus Coordination for Sustainable Real Time Energy Management

    Directory of Open Access Journals (Sweden)

    Kwang-il Hwang

    2014-07-01

    Full Text Available Even though WM-Bus is being considered to be the most promising network protocol for smart metering, it is not suitable for a sustainable real-time home energy management system (HEMS, which requires higher reliability and longer lifetime despite real time bi-directional communications. Therefore, in this paper we propose a Bitmap-wise WM-Bus (BWM-Bus, coping well with sustainable real-time HEMS. In particular, the proposed scheme addresses the several problems in WM-Bus for HEMS by introducing novel functions: asynchronous meter trigger, adaptive slot scheduling, and bitmap-wise retransmission request. Through experiments, we demonstrate that BWM-Bus guarantees higher data success ratio with lower data aggregation time, as well as longer lifetime than WM-Bus standard.

  19. A Model of Bus Bunching under Reliability-based Passenger Arrival Patterns

    OpenAIRE

    Fonzone, Achille; Schmöcker, Jan-Dirk; Liu, Ronghui

    2015-01-01

    If bus service departure times are not completely unknown to the passengers, non-uniform passenger arrival patterns can be expected. We propose that passengers decide their arrival time at stops based on a continuous logit model that considers the risk of missing services. Expected passenger waiting times are derived in a bus system that allows also for overtaking between bus services. We then propose an algorithm to derive the dwell time of subsequent buses serving a stop in order to illustr...

  20. The Bus Extension Module Design and Verification of POSAFE-Q Using LVDS

    International Nuclear Information System (INIS)

    Lee, Youn Sang; Song, Seung Whan; No, Young Hun; Yoo, Kwan Woo

    2012-01-01

    This paper described the Bus Extension Module using Low Voltage Differential Signal (LVDS). A Bus Extension Module use Safety-Related PLC (Programmable Logic Controller), called POSAFE-Q (made by POSCO ICT), for handling many data (I/O) extension rack. A processor module of POSAFE-Q can control I/O Module installed another rack. This paper explains Bus Extension Module and Data transfer technology using LVDS. (author)

  1. Small Explorer Data System MIL-STD-1773 fiber optic bus

    Science.gov (United States)

    Flanegan, Mark; Label, Ken

    1992-01-01

    The MIL-STD-1773 Fiber Optic Data Bus as implemented in the GSFC Small Explorer Data System (SEDS) for the Small Explorer Program is described. It provides an overview of the SEDS MIL-STD-1773 bus components system design considerations, reliability figures, acceptance and qualification testing requirements, radiation requirements and tests, error handling considerations, and component heritage. The first mission using the bus will be launched in June of 1992.

  2. Evaluation of Urban Bus Transport Failure in Gujranwala City of Pakistan

    Directory of Open Access Journals (Sweden)

    MUHAMMAD WAQAR ASLAM

    2017-07-01

    Full Text Available This research work has evaluated the performance of urban public bus transport service operating in Gujranwala city of Pakistan. The assessment has been made in terms of financial viability, bus condition, operational performance and user perception. Based on the data requirements, various traffic/transport surveys were conducted including Passenger Boarding and Alighting Survey, Bus Count Survey, Bus Inspection Survey, Illegal Operations Survey and Public Transport User Interview Survey in consultation with concerned department/agencies. Field surveys were also conducted to get input from passengers and local people. Initial investigation informed that out of four operational bus routes, only two routes are profitable. The overall bus operation is running in loss (only 0.3% net profit. It has barely any profit for the bus operator against its investment thereby making the urban bus operation financially non-viable. The whole revenue flow is dependent on passenger ticketing revenue only. Around 35% of the buses are in poor condition with major issues of quality of tyres, no speedometer, worse condition of seats, floor and ceiling, and display of route. Illegal operation of Qingqis/Rickshaws (as para-transit mode along the bus routes is also decreasing the revenue by capturing the passenger volume. According to passenger opinion analysis, around 55% of the passenger are not satisfied with the service quality and prefer other modes of transport. Their major concerns are absence of facilities for disables and bus stops, bus seating and standing capacity, poor bus condition and pick pocketing. Collectively, these factors are contributing

  3. The impact of bus drivers ’ lifestyle on the occurrence of health problems and absenteeism

    OpenAIRE

    Andrej Jerman; Maja Meško

    2016-01-01

    Research Question: Do bus drivers’ lifestyles affect the occurrence of health problems and absenteeism? Purpose: The purpose of the study was to determine whether the lifestyle of professional bus drivers affects the occurrence of health problems and the phenomenon of absenteeism. Method: A quantitative research method was used in the research. Data were collected using a structured questionnaire, on a sample of 230 professional bus drivers from differ...

  4. Best Operational and Maintenance Practices for City Bus Fleets to Maximize Fuel Economy

    OpenAIRE

    Energy Sector Management Assistance Program

    2011-01-01

    In most large cities in developing countries, buses continue to be the public transport option of choice, carrying a large share of urban travelers. However, transit bus companies in these countries are often cash-strapped. In many cases, the operating cost per bus kilometer exceeds revenues and bus fares are often kept low irrespective of the cost of providing service. Many cities are dom...

  5. Analysis of bus passenger comfort perception based on passenger load factor and in-vehicle time.

    Science.gov (United States)

    Shen, Xianghao; Feng, Shumin; Li, Zhenning; Hu, Baoyu

    2016-01-01

    Although bus comfort is a crucial indicator of service quality, existing studies tend to focus on passenger load and ignore in-vehicle time, which can also affect passengers' comfort perception. Therefore, by conducting surveys, this study examines passengers' comfort perception while accounting for both factors. Then, using the survey data, it performs a two-way analysis of variance and shows that both in-vehicle time and passenger load significantly affect passenger comfort. Then, a bus comfort model is proposed to evaluate comfort level, followed by a sensitivity analysis. The method introduced in this study has theoretical implications for bus operators attempting to improve bus service quality.

  6. ARCNET as a field bus in the Fermilab linac control system

    International Nuclear Information System (INIS)

    Shea, M.F.; Goodwin, R.W.; Kucera, M.J.; Shtirbu, S.

    1992-01-01

    Data acquisition hardware in accelerator control systems is connected by a field bus to networked computers that supply data to consoles. Industry attempts to standardize on a low level field bus have not succeeded in providing a single well-supported bus. This paper describes a data acquisition chassis that connects to VMEbus computers using ARCNET, a full featured token-passing local area network, as the field bus. The performance of this technique as implemented in the control system for the Fermilab Linac is given. (author)

  7. Superconducting link bus design for the accelerator project for upgrade of LHC

    International Nuclear Information System (INIS)

    Nobrega, F.; Brandt, J.; Cheban, S.; Feher, S.; Kaducak, M.; Kashikhin, V.; Peterson, T.

    2011-01-01

    The Accelerator Project for Upgrade of LHC (APUL) is a U.S. project participating in and contributing to CERN's Large Hadron Collider (LHC) upgrade program. Fermi National Accelerator Laboratory in collaboration with Brookhaven National Laboratory was developing sub-systems for the upgrade of the LHC final focus magnet systems. Part of the upgrade called for various lengths of superconducting power transmission lines known as SC Links which were up to 100 m long. The SC Link electrically connects the current leads in the Distribution Feed Boxes to the interaction region magnets. The SC Link is an extension of the magnet bus housed within a cryostat. The present concept for the bus consists of 22 power cables, 4 x 13 kA, 2 x 7 kA, 8 x 2.5 kA and 8 x 0.6 kA bundled into one bus. Different cable and strand possibilities were considered for the bus design including Rutherford cable. The Rutherford cable bus design potentially would have required splices at each sharp elbow in the SC Link. The advantage of the round bus design is that splices are only required at each end of the bus during installation at CERN. The round bus is very flexible and is suitable for pulling through the cryostat. Development of the round bus prototype and of 2 splice designs is described in this paper. Magnetic analysis and mechanical test results of the 13 kA cable and splices are presented.

  8. Hierarchical Delay-Dependent Distributed Coordinated Control for DC Ring-Bus Microgrids

    DEFF Research Database (Denmark)

    Dou, Chunxia; Yue, Dong; Zhang, Zhanqiang

    2017-01-01

    In this paper, a hierarchical distributed coordinated control method is proposed based on the multi-agent system for dc ring-bus microgrids to improve the bus voltage performance. First, a two-level multi-agent system is built, where each first-level unit control agent is associated with a distri......In this paper, a hierarchical distributed coordinated control method is proposed based on the multi-agent system for dc ring-bus microgrids to improve the bus voltage performance. First, a two-level multi-agent system is built, where each first-level unit control agent is associated...

  9. Analyzing the Relationship Between Bus Pollution Policies and Morbidity Using a Quasi-Experiment.

    Science.gov (United States)

    Ngo, Nicole S

    2015-09-01

    Transit buses are used by millions of commuters every day, but they emit toxic diesel fumes. In 1988, the U.S. Environmental Protection Agency implemented emission standards for transit buses, which have been continually updated. Yet there is no quantitative evidence of the health benefits from these bus pollution policies due to data constraints and confounding variables. In this study, a quasi-experiment is used to exploit the geographic and temporal variation in emission standards by using bus vintage as a proxy for bus emissions. This is accomplished using a unique, rich panel data set, which includes daily information on bus vintage and route for the New York City Transit bus fleet between 2006 and 2009. This information is merged with daily data on emergency department (ED) visits for respiratory illnesses, which include patients' residences at the census block level and exact admission date. Economic benefits resulting from these bus pollution policies are then estimated. Results show that stricter transit bus emission standards by the U.S. Environmental Protection Agency for particulate matter are associated with reduced ED visits for respiratory diseases for patients living within a few hundred feet of a bus route. These findings demonstrate that bus pollution policies have made critical improvements to public health.

  10. Concentrations and risk assessment of selected monoaromatic hydrocarbons in buses and bus stations of Hangzhou, China.

    Science.gov (United States)

    Li, Shuang; Chen, Shuguang; Zhu, Lizhong; Chen, Xiasheng; Yao, Chaoying; Shen, Xueyou

    2009-03-01

    Air pollution surveys of ten selected monoaromatic hydrocarbons (MAHCs) were conducted in buses and bus stations in Hangzhou, China. The mean concentrations of MAHCs in the air of buses and bus stations were 95.9 and 36.5 microg/m(3), respectively, of which toluene was the highest in all the sampling sites. Mean concentrations of all MAHCs in buses were statistically higher than those nearby bus stations (pbus drivers were 1.11x10(-5) and 4.00x10(-5), respectively, which were way above the limit set by USEPA. The health risk caused by MAHCs in bus microenvironment should be cautioned.

  11. Exposure of motorcycle, car and bus commuters to carbon monoxide on a main road in the Tel Aviv metropolitan area, Israel.

    Science.gov (United States)

    Potchter, Oded; Oz, Meirav; Brenner, Shmuel; Yaakov, Yaron; Schnell, Izhak

    2014-12-01

    Short-term personal exposure of passengers in different types of motor vehicles to carbon monoxide was investigated in an intensively used main road in Israel's Tel Aviv metropolitan area. According to monitoring stations of the Ministry for Environmental Protection (MEP), concentrations of carbon monoxide (CO) along the road, at a height of 3 m above pedestrian level, in the Tel Aviv metropolitan area, are currently very low. However, these measurements do not reflect the actual exposure of commuters, which were the main objective of this study. Four vehicle types/travel modes were investigated: private cars with closed windows, private cars with open windows, motorcycles, and buses. The commuter CO average exposure was the accumulative exposure divided by the duration of the sampling taken along the route, for each type of vehicles. The results showed that commuters in cars with closed windows were exposed to the highest mean CO level, 27.2 ppm, for a period of 38 min; those in a car with open windows, to 19.7 ppm for 38 min; motorcycle riders, to 12.8 ppm, for 17 min; and bus users were exposed to the lowest mean pollution level, of only 3.6 ppm, for 25 min. Thus, CO values of 1 to 3 ppm, as measured at an MEP adjacent monitoring station, may indicate the exposure to CO pollution of area residents, but do not represent the actual exposure of commuters on the congested main road.

  12. Massachusetts Fuel Cell Bus Project: Demonstrating a Total Transit Solution for Fuel Cell Electric Buses in Boston

    Energy Technology Data Exchange (ETDEWEB)

    2017-05-22

    The Federal Transit Administration's National Fuel Cell Bus Program focuses on developing commercially viable fuel cell bus technologies. Nuvera is leading the Massachusetts Fuel Cell Bus project to demonstrate a complete transit solution for fuel cell electric buses that includes one bus and an on-site hydrogen generation station for the Massachusetts Bay Transportation Authority (MBTA). A team consisting of ElDorado National, BAE Systems, and Ballard Power Systems built the fuel cell electric bus, and Nuvera is providing its PowerTap on-site hydrogen generator to provide fuel for the bus.

  13. DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Elana M. Chapman; Shirish Bhide; Jennifer Stefanik; Andre L. Boehman; David Klinikowski

    2003-04-01

    The objectives of this research and demonstration program are to convert a campus shuttle bus to operation on dimethyl ether, a potential ultra-clean alternative diesel fuel. To accomplish this objective, this project includes laboratory evaluation of a fuel conversion strategy, as well as, field demonstration of the DME-fueled shuttle bus. Since DME is a fuel with no lubricity (i.e., it does not possess the lubricating quality of diesel fuel), conventional fuel delivery and fuel injection systems are not compatible with dimethyl ether. Therefore, to operate a diesel engine on DME one must develop a fuel-tolerant injection system, or find a way to provide the necessary lubricity to the DME. In this project, they have chosen the latter strategy in order to achieve the objective with minimal need to modify the engine. The strategy is to blend DME with diesel fuel, to obtain the necessary lubricity to protect the fuel injection system and to achieve low emissions. The laboratory studies have included work with a Navistar V-8 turbodiesel engine, demonstration of engine operation on DME-diesel blends and instrumentation for evaluating fuel properties. The field studies have involved performance, efficiency and emissions measurements with the Champion Motorcoach ''Defender'' shuttle bus which will be converted to DME-fueling. The results include baseline emissions, performance and combustion measurements on the Navistar engine for operation on a federal low sulfur diesel fuel (300 ppm S). Most recently, they have completed engine combustion studies on DME-diesel blends up to 30 wt% DME addition.

  14. Scheduling with Bus Access Optimization for Distributed Embedded Systems

    DEFF Research Database (Denmark)

    Eles, Petru; Doboli, Alex; Pop, Paul

    2000-01-01

    of control. Our goal is to derive a worst case delay by which the system completes execution, such that this delay is as small as possible; to generate a logically and temporally deterministic schedule; and to optimize parameters of the communication protocol such that this delay is guaranteed. We have......In this paper, we concentrate on aspects related to the synthesis of distributed embedded systems consisting of programmable processors and application-specific hardware components. The approach is based on an abstract graph representation that captures, at process level, both dataflow and the flow......, generates an efficient bus access scheme as well as the schedule tables for activation of processes and communications....

  15. Development of bus duct inspection robot at nuclear power plant

    International Nuclear Information System (INIS)

    Hamada, Mamoru; Hoshi, Teruaki; Komura, Yoshinari

    2017-01-01

    Under the present situation, nuclear power plant has some places which are inspected with difficulty or not inspected due to narrowness or physical restriction, when carrying out periodical inspection. The subject of our research and development is to improve the accuracy of inspection and also to save labor (liberation from distress work of the worker) by applying a robot technology to the periodical inspection of the nuclear power plant. As a specific example, we report that developed robot can inspect inside the narrow space of Isolated Phase Bus ducts, which connect between a turbine generator and the main transformer. (author)

  16. Multifactor-Driven Hierarchical Routing on Enterprise Service Bus

    Science.gov (United States)

    Mi, Xueqiang; Tang, Xinhuai; Yuan, Xiaozhou; Chen, Delai; Luo, Xiangfeng

    Message Routing is the foremost functionality on Enterprise Service Bus (ESB), but current ESB products don't provide an expected solution for it, especially in the aspects of runtime route change mechanism and service orchestration model. In order to solve the above drawbacks, this paper proposes a multifactor-driven hierarchical routing (MDHR) model. MDHR defines three layers for message routing on ESB. Message layer gives the original support for message delivery. Application layer can integration or encapsulate some legacy applications or un-standard services. Business layer introduces business model to supplies developers with a business rule configuration, which supports enterprise integration patterns and simplifies the service orchestration on ESB.

  17. BC Transit Fuel Cell Bus Project Evaluation Results: Second Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L.; Post, M.

    2014-09-01

    Second report evaluating a fuel cell electric bus (FCEB) demonstration led by British Columbia Transit (BC Transit) in Whistler, Canada. BC Transit is collaborating with the California Air Resources Board and the U.S. Department of Energy's National Renewable Energy Laboratory to evaluate the buses in revenue service. NREL published its first report on the demonstration in February 2014. This report is an update to the previous report; it covers 3 full years of revenue service data on the buses from April 2011 through March 2014 and focuses on the final experiences and lessons learned.

  18. Economic Optimization Analysis of Chengdu Electric Community Bus Operation

    Science.gov (United States)

    Yidong, Wang; Yun, Cai; Zhengping, Tan; Xiong, Wan

    2018-03-01

    In recent years, the government has strongly supported and promoted electric vehicles and has given priority to demonstration and popularization in the field of public transport. The economy of public transport operations has drawn increasing attention. In this paper, Chengdu wireless charging pure electric community bus is used as the research object, the battery, air conditioning, driver’s driving behavior and other economic influence factors were analyzed, and optimizing the operation plan through case data analysis, through the reasonable battery matching and mode of operation to help businesses effectively save operating costs and enhance economic efficiency.

  19. Fuel options for public bus fleets in Sweden

    OpenAIRE

    Xylia, Maria; Silveira, Semida

    2015-01-01

    The Swedish public transport sector has defined two major targets, i.e., to run 90% of the total vehicle kilometers of the fleet on non-fossil fuels and double the volume of travel via public transport by 2020, increasing the share of public transport in relation to the total personal transport in the country . The f3 report Fuel options for public bus fleets in Sweden highlights the challenges and solutions encountered, particularly when it comes to the adoption of renewable fuels in the reg...

  20. Idle reduction programs and potential benefits to schools

    Science.gov (United States)

    2010-11-01

    School districts in Texas and many other states have, in recent years, increased the walk zones : surrounding schools to a 2-mile perimeter. Inside this perimeter, either no school bus service is : offered, or service is offered only with a fee...

  1. Reducing School Violence in Florida. Hot Topics: Usable Research.

    Science.gov (United States)

    Kadel, Stephanie; Follman, Joseph

    Violence pervades schools across the nation, disrupting school functioning and preventing students and teachers from learning and teaching. The most effective crisis management and response strategies are designed by a school team that includes administrators, faculty and staff, students, parents, bus drivers and other support staff, as well as…

  2. Evaluation of intelligent transport systems impact on school transport safety

    Directory of Open Access Journals (Sweden)

    Jankowska-Karpa Dagmara

    2017-01-01

    Full Text Available The integrated system of safe transport of children to school using Intelligent Transport Systems was developed and implemented in four locations across Europe under the Safeway2School (SW2S project, funded by the EU. The SW2S system evaluation included speed measurements and an eye-tracking experiment carried out among drivers who used the school bus route, where selected elements of the system were tested. The subject of the evaluation were the following system elements: pedestrian safety system at the bus stop (Intelligent Bus Stop and tags for children, Driver Support System, applications for parents’ and students’ mobile phones, bus stop inventory tool and data server. A new sign designed for buses and bus stops to inform about child transportation/children waiting at the bus stop was added to the system. Training schemes for system users were also provided. The article presents evaluation results of the impact of selected elements of the SW2S system on school transport safety in Poland.

  3. CFD analysis of flow in engine compartment of large urban bus; Ogata bus no engine room nai nagare kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Hoshino, H; Otake, M; Iioka, K [Nissan Diesel Motor Co. Ltd., Saitama (Japan); Sato, K [Subaru Research Center Co. Ltd., Tokyo (Japan)

    1997-10-01

    A CFD simulation was performed to analyze the air flow in the engine compartment of a large urban bus. The conventional simulation technique takes a long time to perform the parameter study of a complex engine compartment shape. In this study, the use of orthogonal grids made modeling the engine compartment easy, so parameter study on modification of the engine compartment structure could be conducted in a short time. Thus this simulation enables engineers to more clearly understand the air flow patterns in the engine compartment, and to get guidlines for modifying the compartment structure to improve the cooling performance. 1 ref., 12 figs.

  4. King County Metro Battery Electric Bus Demonstration: Preliminary Project Results

    Energy Technology Data Exchange (ETDEWEB)

    2017-05-22

    The U.S. Federal Transit Administration (FTA) funds a variety of research projects that support the commercialization of zero-emission bus technology. To evaluate projects funded through these programs, FTA has enlisted the help of the National Renewable Energy Laboratory (NREL) to conduct third-party evaluations of the technologies deployed under the FTA programs. NREL works with the selected agencies to evaluate the performance of the zero-emission buses compared to baseline conventional buses in similar service. The evaluation effort will advance the knowledge base of zero-emission technologies in transit bus applications and provide 'lessons learned' to aid other fleets in incrementally introducing next generation zero-emission buses into their operations. This report provides preliminary performance evaluation results from a demonstration of three zero-emission battery electric buses at King County Metro in King County, Washington. NREL developed this preliminary results report to quickly disseminate evaluation results to stakeholders. Detailed evaluation results will be published in future reports.

  5. Operational efficiency of the lighting system of bus salons

    Directory of Open Access Journals (Sweden)

    Brytkovskyi V.M.

    2016-08-01

    Full Text Available In recent years the problem of safety of people is studied primarily in aspects of natural and man-made disasters, fire, health and safety in the workplace. A problem connected with the way of life of the people, in particular with the use of bus transport remains almost out of sight. In addition to the foregoing, there is another side to the issue: modern development of industry and transport is characterized by large-scale introduction of technical measures aimed at saving energy In the specified aspect theoretical dependences for evaluation of technological economic efficiency of light sources in indoor lighting system buses are grounded. This theoretical dependency will make analytical framework justification applying the respective sources of light, taking into account the hygiene requirements to illumination. The methodology of calculation of economic efficiency of lighting of bus salons is offered. Estimating parameter is justified relative objective function value costs per unit of time or distance. The greatest costs are typical for lamps with incandescent bulbs. The least is common to lamps with fluorescent lamps. Led bulbs have no significant advantage even over incandescent lamps. The reason for this is the relatively high color temperature radiation of LED lamps that requires more light levels and, consequently, the high cost of energy, as well as relatively large initial cost of these lamps.

  6. Design of a steering stabilizer based on CAN bus

    Science.gov (United States)

    Zhan, Zhaomin; Yan, Yibin

    2018-04-01

    This design realizes a posture correction device of griping steering wheel based on CAN bus, which is embedded in the steering wheel of vehicles. The system aims to detect the drivers' abnormal griping postures and provides drivers with classification alerts, by combining the recorded griping postures data and the vehicle speed data that are obtained via the CAN bus. The warning information are automatically stored and retained in the device for 12 months. To enhance the alerting effect, the count of this warning message for both the latest month and the last 12 months are displayed on the dashboard panel. In addition to prevent itself from being blocked and self-detect any faults in advance, the appliance also provide a self-test function, which will communicate with the integrated instrument system in vehicle and do simulation test right after the vehicle power on. This appliance can help to urge and ensure drivers to operate the steering wheel correctly, effectively, and timely; prevent some typical incorrect behaviors which commonly happen along with the change of griping postures, such as the using cellphone, and ultimately, reduce the incidence of traffic accidents.

  7. A programmable systolic trigger processor for FERA bus data

    International Nuclear Information System (INIS)

    Appelquist, G.; Hovander, B.; Sellden, B.; Bohm, C.

    1992-09-01

    A generic CAMAC based trigger processor module for fast processing of large amounts of ADC data, has been designed. This module has been realised using complex programmable gate arrays (LCAs from XILINX). The gate arrays have been connected to memories and multipliers in such a way that different gate array configurations can cover a wide range of module applications. Using this module, it is possible to construct complex trigger processors. The module uses both the fast ECL FERA bus and the CAMAC bus for inputs and outputs. The latter, however, is primarily used for set-up and control but may also be used for data output. Large numbers of ADCs can be served by a hierarchical arrangement of trigger processor modules, processing ADC data with pipe-line arithmetics producing the final result at the apex of the pyramid. The trigger decision will be transmitted to the data acquisition system via a logic signal while numeric results may be extracted by the CAMAC controller. The trigger processor was originally developed for the proposed neutral particle search experiment at CERN, NUMASS. There it was designed to serve as a second level trigger processor. It was required to correct all ADC raw data for efficiency and pedestal, calculate the total calorimeter energy, obtain the optimal time of flight data and calculate the particle mass. A suitable mass cut would then deliver the trigger decision. More complex triggers were also considered. (au)

  8. Development of a multi-mode hybrid electric bus

    Energy Technology Data Exchange (ETDEWEB)

    Shemmans, M.J. [Overland Custom Coach, Thorndale, ON (Canada); Bland, C. [BET Services Inc., Mississauga, ON (Canada)

    2004-04-01

    This paper describes the development of an energy efficient, low floor, 28 foot hybrid electric bus for use as an airport shuttle bus or other specialized transit operations. A multi-mode concept was also adopted to include the capability of operating in battery-only drive, engine-only drive or a range of hybrid electric drive modes. The electric drivetrain was powered by a battery pack or a combination of a battery pack and an internal combustion engine-powered electric generator. The participating companies in this project include Overland Custom Coach, BET Services Inc., Siemens and Transport Canada. The technical feasibility study was described with reference to duty cycles, performance issues, vehicle weight, mechanical drive issues, brakes, suspension, powertrain cooling, heating, ventilation, electrical system, batteries and control system. The commercial feasibility was also described in terms of capital and operating costs. Results of the prototype tests validate the possibilities of zero or reduced emission transit in real world applications. 25 tabs., 32 figs.

  9. Studying customer loyalty at Daewoo express bus service, Pakistan

    Directory of Open Access Journals (Sweden)

    Usman Yousaf

    2013-09-01

    Full Text Available Background: Meeting service quality standards and striving for loyalty are two critical areas which have until now been overlooked by both the passenger transport industry and academia in Pakistan therefore the study sheds useful light on an issue hitherto untouched. Therefore increased sample size will help in increasing generalizability of study. Methods: This paper is designed to study the level of loyalty at Daewoo Express Bus Service in Sargodha by measuring customer satisfaction. Researchers used a small sample of only 96 respondents (passengers and only studies customer's behavior in the service quality of Daewoo Express Bus Service however it may differ in other passenger transport services. Results and conclusions: This paper reveals that there is a positive and significant relationship between loyalty (dependant variable and price perceptions, reliability, retrieving and smoothing (independent variables. However, the study found that reliability of services is the most important dimension among other independent variables (price perceptions, smoothing, reliability, retrieving effecting customers loyalty at Daewoo Express. Paper under consideration would surely assist Daewoo`s management team to take care of the loopholes existing in the current service level and likely threats which Daewoo might face.

  10. CERPEN FARUK “BUS KOTA” DALAM SEMIOTIK ROLAND BARTHES

    Directory of Open Access Journals (Sweden)

    Ken Widyatwati

    2016-04-01

    Full Text Available Literature called beautiful if it contains the mandate, message, ideas and meanings that are useful for the readers. Short story “Bus Kota” (City Bus containing the mandate, message, ideas and meanings that are useful to the reader. The mandate will be revealed by Roland Barthes' semiotic theory in the book S/Z. Literature has its own allure and text have accrued but not due to independence because of the difference in quality. Texts merge into a unity, or restore any text not as an individual but as a form of plurality. Literature as part of a social system is an expression of the author's sense of the outpouring of public life. Literary works can express themselves in the author's view the social and cultural changes in society because of the development of information technology and rapid. Technological developments and socio-cultural information can change in society so as to affect the psychology of the people. Society must have a thickness of faith not only for themselves, but to be able to maintain equanimity in the life of a pluralistic society

  11. A fuel cell city bus with three drivetrain configurations

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Junping [Key Laboratory of Education Ministry for Modern Design and Rotor-Bearing System, Xi' an Jiaotong University, Xi' an 710049 (China); Chen, Yong [School of Automobile and Transporting Engineering, Liaoning Institute of Technology, Jinzhou, Liaoning 121001 (China); Chen, Quanshi [State Key Laboratory of Automobile Safety and Energy Conservation, Tsinghua University, Beijing 100084 (China)

    2006-09-22

    Three fuel cell city buses of the energy hybrid- and power hybrid-type were re-engineered with three types of drivetrain configuration to optimize the structure and improve the performance. The energy distribution, hydrogen consumption, state of charge (SOC) and the power variation rate were analyzed when different drivetrain configurations and parameters were used. When powered only by a fuel cell, the bus cannot recover the energy through regenerative braking. The variation of the fuel cell power is large and frequent, which is not good for the fuel cell. When the fuel cell is linked to a battery pack in parallel, the bus can recover the energy through regenerative braking. The energy distribution is determined by the parameters of the fuel cell and the battery pack in the design stage to reduce the power variation rate of the fuel cell. When the fuel cell and DC/DC converter connected in series links the battery pack in parallel, energy can be recovered and the energy distribution can be adjusted online. The power variation rate of both the fuel cell and the battery pack are reduced. (author)

  12. Channel access: A software bus for the LAACS

    International Nuclear Information System (INIS)

    Hill, J.O.

    1990-01-01

    The host processor for a code running within a distributed process control system is often predetermined by constraints built into the software architecture of the control system. Input/output (I/O) channels directly connected to the host processors are usually easier to access in software than channels on remote processors. It is often difficult to modernize selective parts of a control system's software while leaving the other parts unchanged. Likewise, software developed at one laboratory is often difficult to integrate into a control system developed at another laboratory. Software that runs in one machine or operating-system architecture is often unable to communicate with control-system software running on a different platform. For the Los Alamos Accelerator Control System (LAACS) we have attempted to address the above difficulties with a software communication facility which we call Channel Access. Channel Access provides a 'software bus' that allows programs to be connected through a network to I/O channels on real-time processors in a manner similar to the way in which hardware modules are integrated within a standardized hardware bus such as CAMAC or VME. We have already placed an operator interface on Channel Access and we are currently designing alarm, archiving and sequencing tools as well. Numerous application-specific programs use Channel Access. This paper describes the unique feature of this approach and its performance as an integral part of the Los Alamos Accelerator Control System. (orig.)

  13. Particulate air pollution and vascular reactivity: the bus stop study.

    Science.gov (United States)

    Dales, Robert; Liu, Ling; Szyszkowicz, Mietek; Dalipaj, Mary; Willey, Jeff; Kulka, Ryan; Ruddy, Terrence D

    2007-11-01

    Particulate air pollution is associated with cardiovascular morbidity but mechanisms are not well understood. We tested the effects on vascular reactivity of exposure to fine particulates matter mass (PM(2.5)), number of particles bus stops. Flow-mediated vasodilation (FMD) of the brachial artery was then measured by ultrasound and expressed as: (maximum artery diameter after release of a blood pressure cuff inflated above systolic pressure-baseline resting diameter)/baseline resting diameter. A 30 microg/m(3) increase in PM(2.5) exposure corresponded to a 0.48% reduction in FMD, P=0.05 representing a 5% relative change in the maximum ability to dilate. Results were consistent between the two bus stops and not sensitive to type of analysis. No significant association was found between FMD and NO(2), PM(1.0) or traffic density. PM(2.5) may reduce the capacity to vasodilate, a potential explanation for the documented association with cardiovascular morbidity.

  14. Diesel bus emissions measured in a tunnel study.

    Science.gov (United States)

    Jamriska, Milan; Morawska, Lidia; Thomas, Steven; He, Congrong

    2004-12-15

    The emission factors of a bus fleet consisting of approximately 300 diesel-powered buses were measured in a tunnel study under well-controlled conditions during a 2-d monitoring campaign in Brisbane. Particle number and mass concentration levels of submicrometer particles and PM2.5 were monitored by SMPS and DustTrak instruments at the tunnel's entrance and exit, respectively. Correlation between DustTrak and TEOM response to diesel emissions was assessed, and the DustTrak results were recalculated into TEOM equivalent data. The mean value of the number and mass emission factors was (3.11+/-2.41) x 10(14) particles km(-1) for submicrometer particles and 583+/-451 mg km(-1) for PM2.5 (DustTrak), respectively. TEOM PM2.5 equivalent emission factor was 267+/-207 mg km(-1). The results are in good agreement with the emission factors determined from steady-state dynamometer testing of 12 buses from the same Brisbane City bus fleet. The results indicate that when carefully designed, both approaches, the dynamometer and on-road studies, can provide comparable results, applicable for the assessment of the effect of traffic emissions on airborne particle pollution. A brief overview of emission factors determined from other on-road and dynamometer studies reported in the literature as well as with the regulatory values used for the vehicle emission inventory assessment is presented and compared with the results obtained in this study.

  15. Bus Implementation Using New Low Power PFSCL Tristate Buffers

    Directory of Open Access Journals (Sweden)

    Neeta Pandey

    2016-01-01

    Full Text Available This paper proposes new positive feedback source coupled logic (PFSCL tristate buffers suited to bus applications. The proposed buffers use switch to attain high impedance state and modify the load or the current source section. An interesting consequence of this is overall reduction in the power consumption. The proposed tristate buffers consume half the power compared to the available switch based counterpart. The issues with available PFSCL tristate buffers based bus implementation are identified and benefits of employing the proposed tristate buffer topologies are put forward. SPICE simulation results using TSMC 180 nm CMOS technology parameters are included to support the theoretical formulations. The performance of proposed tristate buffer topologies is examined on the basis of propagation delay, output enable time, and power consumption. It is found that one of the proposed tristate buffer topology outperforms the others in terms of all the performance parameters. An examination of behavior of available and the proposed PFSCL tristate buffer topologies under parameter variations and mismatch shows a maximum variation of 14%.

  16. Activities of four bus terminals of Semarang City gateway and the related GHG emission

    Science.gov (United States)

    Huboyo, H. S.; Wardhana, I. W.; Sutrisno, E.; Wangi, L. S.; Lina, R. A.

    2018-01-01

    The activities of the bus terminal, including loading-unloading passengers, bus idling, and bus movements at the terminal, will emit GHG’s emission. This research analyzes GHG emission from four terminals, i.e., Mangkang, Terboyo, Penggaron, and Sukun in Semarang City. The emission was estimated by observing detail activities of public transport means, especially for moving and idling time. The emission was calculated by Tier 2 method based on the vehicle type as well as fuel consumption. The highest CO2e during vehicle movements at Sukun area was contributed by large bus about 2.08 tons/year, while at Terboyo terminal was contributed by medium bus about 347.97 tons/year. At Mangkang terminals, the highest emission for vehicle movements was attributed by medium bus as well of about 53.18 tons/year. At last, Penggaron terminal’s highest GHG emission was attributed by BRT about 26.47 tons/year. During idling time, the highest contributor to CO2e was the large bus at the three terminals, i.e., Sukun of 43.53 tons/year, Terboyo of 196.56 tons/year, and Mangkang of 84.26 tons/year, while at Penggaron, BRT dominated with CO2e of 26.47 tons/year. The management of public transport in terminals is crucial to mitigate the emission related to bus terminals activities.

  17. Acute subdural hemorrhage while traveling by bus: a risk factor in the elderly?

    Science.gov (United States)

    Soysal, Suna; Topacoglu, Hakan; Acarbay, Sabiha; Ozbas, Kerem

    2005-01-01

    A 71-year-old man was delivered to our emergency department by an intercity bus. About 4 hours into a journey, he had complained of a headache to his wife. After one more hour, she noted a change in his level of alertness and notified the bus driver. A computed tomography scan of the head showed a subdural hemorrhage.

  18. 77 FR 74452 - Bus Testing: Calculation of Average Passenger Weight and Test Vehicle Weight

    Science.gov (United States)

    2012-12-14

    ... require FTA to work with bus manufacturers and transit agencies to establish a new pass/ fail standard for... buses from the current value of 150 pounds to a new value of 175 pounds. This increase was proposed to... new pass/fail standards that require a more comprehensive review of its overall bus testing program...

  19. Successfulness of bus rapid transit systems in Asia. Ex-post evaluation

    NARCIS (Netherlands)

    Kogdenko, Nadja

    2010-01-01

    SUMMARY Bus Rapid Transit (BRT) can be defined as “a bus-based mass transit system that delivers fast, comfortable, and cost-effective urban mobility”. It offers the opportunity to create a high-quality mass transit system at affordable costs, which is p

  20. Converter Power Density Increase using Low Inductive Integrated DC-link Capacitor/Bus

    DEFF Research Database (Denmark)

    Trintis, Ionut; Franke, Toke; Rannested, Bjørn

    2015-01-01

    The power losses in switching devices have a direct effect on the maximum converter power. For a voltage source converter, the DC-link bus has a major influence on the power loss and safe operating area of the power devices. The Power Ring Film CapacitorTM integrated with an optimized bus structu...

  1. Evoking Emotions and Unpacking Layered Histories through Young Children's Illustrations of Racial Bus Segregation

    Science.gov (United States)

    Kuby, Candace R.

    2013-01-01

    Drawing on theories of multi-modality and critical visual literacy, this article focuses on images that five-and six year-olds painted in a class-made book, Voice on the Bus, about racial segregation. The article discusses how children used illustrations to convey their understandings of Rosa Parks' bus arrest in Alabama. A post-structural view…

  2. Bus Operation Monitoring Oriented Public Transit Travel Index System and Calculation Models

    Directory of Open Access Journals (Sweden)

    Jiancheng Weng

    2013-01-01

    Full Text Available This study proposed a two-dimensional index system which is concerned essentially with urban travel based on travel modes and user satisfaction. First, the public transit was taken as an example to describe the index system establishing process. In consideration of convenience, rapid, reliability, comfort, and safety, a bus service evaluation index system was established. The indicators include the N-minute coverage of bus stops, average travel speed, and fluctuation of travel time between stops and bus load factor which could intuitively describe the characteristics of public transport selected to calculate bus travel indexes. Then, combined with the basic indicators, the calculation models of Convenience Index (CI, Rapid Index (RI, Reliability Index (RBI, and Comfort Index (CTI were established based on the multisource data of public transit including the real-time bus GPS data and passenger IC card data. Finally, a case study of Beijing bus operation evaluation and analysis was conducted by taking real bus operation data including GPS data and passenger transaction recorder (IC card data. The results showed that the operation condition of the public transit was well reflected and scientifically classified by the bus travel index models.

  3. Air flow through a non-airconditioned bus with open windows

    Indian Academy of Sciences (India)

    Thus, bus travel which is the backbone of public transport in India will continue ... was not possible to replicate the same Reynolds number as in a real bus. With the .... The Kolmogorov time scale, τη can be estimated to be 6 × 10. −3 s. Thus ...

  4. Operating Time Division for a Bus Route Based on the Recovery of GPS Data

    Directory of Open Access Journals (Sweden)

    Jian Wang

    2017-01-01

    Full Text Available Bus travel time is an important source of data for time of day partition of the bus route. However, in practice, a bus driver may deliberately speed up or slow down on route so as to follow the predetermined timetable. The raw GPS data collected by the GPS device equipped on the bus, as a result, cannot reflect its real operating conditions. To address this concern, this study first develops a method to identify whether there is deliberate speed-up or slow-down movement of a bus. Building upon the relationships between the intersection delay, link travel time, and traffic flow, a recovery method is established for calculating the real bus travel time. Using the dwell time at each stop and the recovered travel time between each of them as the division indexes, a sequential clustering-based time of day partition method is proposed. The effectiveness of the developed method is demonstrated using the data of bus route 63 in Harbin, China. Results show that the partition method can help bus enterprises to design reasonable time of day intervals and significantly improve their level of service.

  5. School Climate Improvement Action Guide for Noninstructional Staff. School Climate Improvement Resource Package

    Science.gov (United States)

    National Center on Safe Supportive Learning Environments, 2017

    2017-01-01

    Improving school climate takes time and commitment from a variety of people in a variety of roles. This document outlines key action steps that noninstructional staff--including guidance counselors, social workers, school psychologists, office staff, bus drivers, maintenance and facility staff, and food service staff--can take to support school…

  6. Study on the optimum design of bus window pillar join40t; Bus window pillar ketsugo buzai no saiteki sekkei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tomioka, N [Nihon University, Tokyo (Japan); Lim, S; Kim, M; Lee, H; Kang, S; Bae, D

    1997-10-01

    Automobile body structure is generally assembled using various spot welded box sectional members. Especially, in the case of the bus, the shape of window pillar joint is assembled m T-type. This T-type member has some problem such as high stress concentration, low fatigue strength and structural rigidity. Therefore, in this report, performed a study on the optimum design of the bus window pillar joint for such problem by FEM analysis and experiments. 1 ref., 10 figs., 2 tabs.

  7. In depth analysis of urban accidents involving motorcycle and moped riders in France, construction of prototypical accident scenarios and prospects for their prevention. Poster

    OpenAIRE

    CLABAUX, N

    2007-01-01

    in France, in 2006, in spite of a low part of travel, motorcycle and moped riders accounted for 23% of all traffic fatalities and 31% of all injuries recorded. This extra risk is particularly marked in urban areas and in large cities. According to national accident statistics, in urban areas, accidents involving motorcycles and mopeds account for 20% and 23,6% respectively, of all injury accidents recorded. In the city of Paris, in 2005, powered two-wheelers accounted for 3% of all travel but...

  8. A Study of BUS Architecture Design for Controller of Nuclear Power Plant Using FPGA

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dongil; Yun, Donghwa; Hwang, Sungjae; Kim, Myeongyun; Lee, Dongyun [PONUTech Co. Ltd., Seoul (Korea, Republic of)

    2014-05-15

    CPU (Central Processing Unit) operating speed and communication rate have been more technically improved than before. However, whole system is been a degradation of performance by electronic and structural limitation of parallel bus. Transmission quantity and speed have a limit and need arbiter in order to do arbitration because several boards shared parallel bus. Arbiter is a high complexity in implementing so it increases component per chip. If a parallel bus uses, it will occurs some problems what are reflection noise, power/ground noise (or ground bounce) as SSN (Simultaneous Switching Noise) and crosstalk noise like magnetic coupling. In this paper, in order to solve a problem of parallel bus in controller of NPP (Nuclear Power Plant), proposes the bus architecture design using FPGA (Field Programmable Gate Array) based on LVDS (Low Voltage Differential Signaling)

  9. A Study of BUS Architecture Design for Controller of Nuclear Power Plant Using FPGA

    International Nuclear Information System (INIS)

    Lee, Dongil; Yun, Donghwa; Hwang, Sungjae; Kim, Myeongyun; Lee, Dongyun

    2014-01-01

    CPU (Central Processing Unit) operating speed and communication rate have been more technically improved than before. However, whole system is been a degradation of performance by electronic and structural limitation of parallel bus. Transmission quantity and speed have a limit and need arbiter in order to do arbitration because several boards shared parallel bus. Arbiter is a high complexity in implementing so it increases component per chip. If a parallel bus uses, it will occurs some problems what are reflection noise, power/ground noise (or ground bounce) as SSN (Simultaneous Switching Noise) and crosstalk noise like magnetic coupling. In this paper, in order to solve a problem of parallel bus in controller of NPP (Nuclear Power Plant), proposes the bus architecture design using FPGA (Field Programmable Gate Array) based on LVDS (Low Voltage Differential Signaling)

  10. SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Second Results Report and Appendices

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, L.; Chandler, K.

    2011-10-01

    This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. This is the second results report for the AT fuel cell bus since it was placed in service, and it focuses on the newest data analysis and lessons learned since the previous report. The appendices, referenced in the main report, provide the full background for the evaluation. They will be updated as new information is collected but will contain the original background material from the first report.

  11. Active Power Filter DC Bus Voltage Piecewise Reaching Law Variable Structure Control

    Directory of Open Access Journals (Sweden)

    Baolian Liu

    2014-01-01

    Full Text Available The DC bus voltage stability control is one key technology to ensure that Active Power Filter (APF operates stably. The external disturbances such as power grid and load fluctuation and the system parameters changing may affect the stability of APF DC bus voltage and the normal operation of APF. The mathematical model of DC bus voltage is established according to power balance principle and a DC bus voltage piecewise reaching law variable structure control algorithm is proposed to solve the above problem, and the design method is given. The simulation and experiment results proved that the proposed variable structure control algorithm can eliminate the chattering problem existing in traditional variable structure control effectively, is insensitive to system disturbance, and has good robustness and fast dynamic response speed and stable DC bus voltage with small fluctuation. The above advantages ensure the compensation effect of APF.

  12. Bus driving assistance system for town area by using ATmega328P microcontroller

    Science.gov (United States)

    Zakaria, Mohamad Fauzi; Soon, Tan Jiah; Rohani, Munzilah Md

    2017-09-01

    Recently, several bus accidents happened because of bus driver's behavior. In fact, there is no dedicated tool for assisting them to drive safely. This project gives solutions to this by assisting the driver, according to the speed and acceleration of the bus. These data are collected by using a motion processing unit (MPU-6050) and a global positioning system (GPS) and then indicate the driving mode status on the LEDs. All data and status are recorded in a secure digital (SD) card for the authority or the bus company to analyze the driving behavior of a bus driver. This system has been successfully developed and tested in two different areas which includes the UTHM main campus and the road from Parit Raja to Batu Pahat.

  13. Predicting self-pollution inside school buses using a CFD and multi-zone coupled model

    Science.gov (United States)

    Li, Fei; Lee, Eon S.; Liu, Junjie; Zhu, Yifang

    2015-04-01

    The in-cabin environment of a school bus is important for children's health. The pollutants from a bus's own exhaust contribute to children's overall exposure to air pollutants inside the school bus cabin. In this study, we adapted a coupled model originally developed for indoor environment to determine the relative contribution of the bus own exhaust to the in-cabin pollutant concentrations. The coupled model uses CFD (computational fluent dynamics) model to simulate outside concentration and CONTAM (a multi-zone model) for inside the school bus. The model was validated with experimental data in the literature. Using the validated model, we analyzed the effects of vehicle speed and tailpipe location on self-pollution inside the bus cabin. We confirmed that the pollution released from the tailpipe can penetrate into the bus cabin through gaps in the back emergency door. We found the pollution concentration inside school buses was the highest when buses were driven at a medium speed. In addition, locating the tailpipe on the side, behind the rear axle resulted in less self-pollution since there is less time for the suction effect to take place. The developed theoretical framework can be generalized to study other types of buses. These findings can be used in developing policy recommendations for reducing human exposure to air pollution inside buses.

  14. Assessment of Passenger Satisfaction with Public Bus Transport Services: A Case Study of Lucknow City (India

    Directory of Open Access Journals (Sweden)

    Singh Sanjay

    2016-12-01

    Full Text Available The main aim of this study is threefold. First, it tries to assess the passenger satisfaction with public bus transport services in the city of Lucknow in India. Second, it tries to examine the service quality attributes that influence the passenger satisfaction. Third, it tries to evaluate the relative importance of service quality attributes to find out the priority for service quality improvements to enhance passenger satisfaction. The study is based on a survey of objective as well as subjective questions conducted between May and July 2014. Five major bus stops of Lucknow were selected for the survey. Total 148 respondents were randomly selected to elicit their overall satisfaction and factors that influence their satisfaction in the use of public bus transport services in Lucknow using a self-rated questionnaire. The collected sample of responses is subjected to principal component analysis, a statistical technique for dimensionality reduction of the dataset, and descriptive analysis. The result of theses analyses shows that passengers are mostly dissatisfied with public bus transport services in Lucknow. Using principal component analysis, five underlying factors were extracted that influenced passenger satisfaction with public bus transport services in the city. Out of these five factors, comfort and safety has the greatest impact on overall satisfaction, followed by the adequacy of capacity of public bus transport services, orderly and clean environment inside buses, elegant design of buses and bus stops, and accessibility to public bus transport services in the city. The study thus provides a direction for public bus transport administration in the city to understand the gaps that exist and try to fill them to improve its services so that passenger satisfaction can be enhanced and consequently more people can be attracted towards public bus transport.

  15. 49 CFR 37.169 - Interim requirements for over-the-road bus service operated by private entities.

    Science.gov (United States)

    2010-10-01

    ... of such devices, shall be permitted in the passenger compartment. When the bus is at rest at a stop... 49 Transportation 1 2010-10-01 2010-10-01 false Interim requirements for over-the-road bus service... Interim requirements for over-the-road bus service operated by private entities. (a) Private entities...

  16. Tinjauan Yuridis Perjanjian Kerjasama Pengadaan Armada Kendaraan Bus Wisata Antara PT. Lingga Jati Al Manshurin Dengan P.O. Karona

    OpenAIRE

    Sinabang, Rajamin P.

    2010-01-01

    Perkembangan masyarakat telah dipengaruhi oleh kemajuan teknologi. Hal ini yang memperbaharui penggunaan berbagai aturan hukum untuk bentuk-bentuk tertentu, hingga sampai pada bentuk pelayanan (service) tertentu dari pengusaha dalam bidang teknologi, khususnya dalam usaha pengangkutan darat. Sehingga dibutuhkan bus dari perusahaan penyedia armada kendaraan bus untuk pengangkutan tersebut, yaitu melalui perjanjian kerjasama pengadaan armada bus, yang dilakukan oleh PT. Lingga Jati Al Manshurin...

  17. 40 CFR 85.1404 - Maintenance of records for urban bus operators; submittal of information; right of entry.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Maintenance of records for urban bus... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1404 Maintenance of records for urban bus operators; submittal...

  18. Oxidative and nitrosative stress markers in bus drivers.

    Science.gov (United States)

    Rossner, Pavel; Svecova, Vlasta; Milcova, Alena; Lnenickova, Zdena; Solansky, Ivo; Santella, Regina M; Sram, Radim J

    2007-04-01

    Exposure to ambient air pollution is associated with many diseases. Oxidative and nitrosative stress are believed to be two of the major sources of particulate matter (PM)-mediated adverse health effects. PM in ambient air arises from industry, local heating, and vehicle emissions and poses a serious problem mainly in large cities. In the present study we analyzed the level of oxidative and nitrosative stress among 50 bus drivers from Prague, Czech Republic, and 50 matching controls. We assessed simultaneously the levels of 15-F(2t)-isoprostane (15-F(2t)-IsoP) and 8-oxodeoxyguanosine (8-oxodG) in urine and protein carbonyl groups and 3-nitrotyrosine (NT) in blood plasma. For the analysis of all four markers we used ELISA techniques. We observed significantly increased levels of oxidative and nitrosative stress markers in bus drivers. The median levels (min, max) of individual markers in bus drivers versus controls were as follows: 8-oxodG: 7.79 (2.64-12.34)nmol/mmol versus 6.12 (0.70-11.38)nmol/mmol creatinine (p<0.01); 15-F(2t)-IsoP: 0.81 (0.38-1.55)nmol/mmol versus 0.68 (0.39-1.79)nmol/mmol creatinine (p<0.01); carbonyl levels: 14.1 (11.8-19.0)nmol/ml versus 12.9 (9.8-16.6)nmol/ml plasma (p<0.001); NT: 694 (471-3228)nmol/l versus 537 (268-13833)nmol/l plasma (p<0.001). 15-F(2t)-IsoP levels correlated with vitamin E (R=0.23, p<0.05), vitamin C (R=-0.33, p<0.01) and cotinine (R=0.47, p<0.001) levels. Vitamin E levels also positively correlated with 8-oxodG (R=0.27, p=0.01) and protein carbonyl levels (R=0.32, p<0.001). Both oxidative and nitrosative stress markers positively correlated with PM2.5 and PM10 exposure. In conclusion, our study indicates that exposure to PM2.5 and PM10 results in increased oxidative and nitrosative stress.

  19. Integration of refrigerators into facility automation with the aid of bus systems; Integration der Kaeltetechnik in die Gebaeudeautomation mit Bus-Systemen

    Energy Technology Data Exchange (ETDEWEB)

    Baumgarth, S.; Heiser, M. [Fachhochschule Braunschweig-Wolfenbuettel, Wolfenbuettel (DE). Inst. fuer Verbrennungstechnik und Prozessautomation (IVP)

    2000-07-01

    The integration of refrigeration systems in building automation is illustrated by the example of a ventilation system and a cooling ceiling. Cold is supplied by a coldwater unit. This necessitates supply of consumption data to the central refrigeration system. So far, technical facilities are commonly controlled by DDC systems and in-house bus systems. The demand for open communication between different systems resulted in the development of neutral systems like FND and Profibus, which were followed by a multitude of other, less generally accepted systems. In the field of electrical installations, the European Installation Bus EIB was generally accepted as a certified, open bus system which can be combined with DDC technology and integrated in in-house control systems. Another technology developed in the USA is the Local Operating Network, LON, whic has a hither transmission rate and higher information content for the various bus members. The contribution compares the two bus systems. [German] Die Einbindung der Kaeltetechnik in die Gebaeudeautomation wird an den Beispielen Lueftungsanlage und Kuehldecke vorgestellt. Die erforderliche Kaelte soll durch einen Kaltwasserersatz energieoptimiert bereitgestellt werden. Dazu muessen Informationen aus dem Verbraucherbereich in der Kaeltezentrale zur Verfuegung stehen. RTL-Anlagen wurden bisher mittels DDC-Technik und firmenspezifischen Bus-Systemen geregelt und gesteuert. Wenn verschiedene Anlagen durch DDC-Systeme unterschiedlicher Hersteller betrieben wurden, so war anfaenglich eine gemeinsame Ueberwachung auf einer zentralen Leitwarte nur ueber Gateways moeglich. Aus der Forderung nach offener Kommunikation unterschiedlicher Systeme entstanden die ersten firmenneutralen Entwicklungen FND und Profibus. Es folgten eine Vielzahl weiterer Netz- und Busdefinitionen und deren Kommunikationsprotokolle, denen jedoch weitgehend eine allgemeine Anerkennung versagt blieb. Im Bereich der Elektroinstallation profilierte sich der

  20. Air quality inside the passenger compartment of a bus.

    Science.gov (United States)

    Conceição, E Z; Silva, M C; Viegas, D X

    1997-01-01

    The indoor air quality in the passenger compartment of an intercity bus is studied. A system used for the remotion of the contaminants from the compartment, based on an extraction duct, was projected using a simple, unidimensional flow model with capability to predict the air exchange rate as a function of the vehicle velocity. Some tests using tracer gan methods were performed in a real vehicle with the contaminant remotion system mounted, in order to validate the calculation model and evaluate the performances of the system. A good agreement between the predicted and the experimental results was verified and the obtained air exchange rate was quite reasonable when compared with the former situation, without extraction duct.

  1. Research on a Scania 11 liter ethanol fueled bus engine

    Energy Technology Data Exchange (ETDEWEB)

    Egebaeck, K E; Pettersson, E

    1996-05-01

    This report presents research carried out on an alcohol fueled bus engine. The engine used was a six cylinder 11 liter compression ignition turbo-charged engine with an inter cooler. The research program included studies of the impact on the emissions when changing different engine components and different settings of the engine. A study of the impact on the engine performance and emissions when using different fuel compositions was also carried out. During the course of the work, the engine was equipped with oxidation catalysts of two different types, one of which was more efficient than the other concerning the oxidation of unburnt fuel related components. One of the main purposes of the research was to improve the emission characteristics of the engine by an optimization of the engine and its setting. The exhaust emissions were thoroughly characterized with respect to both regulated and unregulated emissions. 13 refs, figs, tabs

  2. Optimum power quality service in multi-bus microgrid systems

    DEFF Research Database (Denmark)

    Meng, Lexuan; Guerrero, Josep M.

    2017-01-01

    Power quality requirements for different consumers and electric equipment are distinguished. Conventionally a common power quality standard is applied to the whole power grid inducing debate between several sides, including consumers, generation sites and technical commissions. Customized power...... quality standard settings for different consumers become a widely accepted solution. The main challenge is on the proper regulation of power quality in different areas. This paper considers a multi-bus microgrid system where the power quality in each has flexible and individual standard. Distributed...... generators are utilized to provide power quality regulation functions. An optimization method based strategy is proposed and implemented with the power converter control system. A general mathematical model is established which can be used in the optimization problem for evaluating the objective function...

  3. Multi Bus DC-DC Converter in Electric Hybrid Vehicles

    Science.gov (United States)

    Krithika, V.; Subramaniam, C.; Sridharan, R.; Geetha, A.

    2018-04-01

    This paper is cotncerned with the design, simulation and fabrication of the prototype of a Multi bus DC- DC converter operating from 42V DC and delivering 14V DC and 260V DC. As a result, three DC buses are interconnected through a single power electronic circuitry. Such a requirement is energized in the development of a hybrid electric automobile which uses the technology of fuel cell. This is implemented by using a Bidirectional DC-DC converter configuration which is ideally suitable for multiple outputs with mutual electrical isolation. For the sake of reduced size and cost of step-up transformer, selection of a high frequency switching cycle at 10 KHz was done.

  4. A fast ECL bus memory: dual input memory

    International Nuclear Information System (INIS)

    Cesaroni, F.; Pascale, G.; Gentile, S.; Gao, Z.

    1992-01-01

    A fast and flexible dual input memory (DIM) has been constructed as single CAMAC unit. The device has been designed to receive via front panel two 16-bit data words, which can be stored in sequential mode into a memory and, at the same time, presented on the output. The design implemented also the possibility to connect 16-bit differential ECL outputs of many DIMs modules on the same bus. Its timing characteristics for writing and reading into and from memory is only 20 ns. This makes the module a useful element for all kinds of fast acquisition systems, as tempory storage of data, or data source or spy module. It will be, for example, used in the new energy tripper of the L3 experiment, designed for 8x8 bunch mode operation of LEP in 1992. (orig.)

  5. FAIR: A new fast trigger and readout bus system

    International Nuclear Information System (INIS)

    Ordine, A.; Boiano, A.; Zaghi, A.

    1998-01-01

    FAIR (FAst Intercrate Readout) is a synchronous ECL bus system dedicated to readout. It is based on a new trigger and readout hardware level protocol and on a new control system that learns how to setup and control modules. The hardware protocol along with the data structure allow both readout and event building at the same time at the rate of 22 ns/longword (1.44 Gbit/s) without the need of CPUs. It performs trigger management and full pipelining by using a multilevel FIFO structure. FAIR provides for a multi-crate front-end environment and uses an embedded serial network to accomplish front-end control and setup. The data transfer measured performances and the control system are presented in some detail

  6. FAKTOR PENYEBAB KERUSAKAN SISTEM MESIN PADA BUS APTB PPD

    Directory of Open Access Journals (Sweden)

    Laela Chairani

    2015-06-01

    Full Text Available Comfort and safety of public transportation, particularly APTB PPD buses, becomes high expectations for its customers. Those expectations must be supported by the application of a good engine maintenance system. By using the method of Reliability Centered Maintenance may be determined appropriate actions to mitigate damage. From the analysis known the failures of the APTB PPD bus are malfunctions of the fuel engine, power transfer systems, difficulty to move the gear lever, and lubricating system for the rough engine noise. The cause of engine malfunction is dirty diesel filter, vehicle acceleration malfunction is due to the clutch plate wear out. Difficulty to move the gear lever indicates that the clutch slips. Rough engine noise caused by the flow of oil to the engine stalled as the result of dirty oil filter. The results of the logic tree analysis show that for each failure requires scheduling of time directed task.

  7. Kajian Implementasi Graph Database pada Rute Bus Rapid Transit

    Directory of Open Access Journals (Sweden)

    Panji Wisnu Wirawan

    2017-12-01

    Full Text Available Bus Rapid Transit (BRT merupakan salah satu sarana transportasi publik yang memiliki rute perjalanan tertentu atau disebut sebagai koridor. Satu koridor BRT dengan koridor yang lain bukanlah koridor yang terpisah, melainkan saling terhubung. Dalam melakukan perjalanan, penumpang BRT boleh jadi melakukan perpindahan koridor melalui shelter. Informasi tersebut perlu didapatkan seorang calon penumpang sebelum melakukan perjalanan supaya tidak terjadi perpindahan koridor yang salah. Teknologi informasi memungkinkan representasi informasi pencarian koridor yang tepat ketika penumpang akan melakukan sebuah perjalanan, terlebih dengan hadirnya graph database. Graph Database memungkinkan representasi BRT yang baik karena sifat graph yang secara standar telah menunjukkan node dan relationship. Artikel ini mengkaji penerapan graph database untuk data pada BRT. Selain itu, artikel ini mendesain sebuah algoritma pencarian koridor BRT. Harapannya, algoritma tersebut dapat digunakan untuk membangun aplikasi yang memanfaatkan data pada graph database. Hasil kajian menunjukkan bahwa graph database dapat diterapkan untuk data BRT dan algoritma yang dibangun dapat digunakan untuk menyajikan informasi rute sekaligus menyampaikan informasi perpindahan koridor.

  8. Using a Control System Ethernet Network as a Field Bus

    CERN Document Server

    De Van, William R; Lawson, Gregory S; Wagner, William H; Wantland, David M; Williams, Ernest

    2005-01-01

    A major component of a typical accelerator distributed control system (DCS) is a dedicated, large-scale local area communications network (LAN). The SNS EPICS-based control system uses a LAN based on the popular IEEE-802.3 set of standards (Ethernet). Since the control system network infrastructure is available throughout the facility, and since Ethernet-based controllers are readily available, it is tempting to use the control system LAN for "fieldbus" communications to low-level control devices (e.g. vacuum controllers; remote I/O). These devices may or may not be compatible with the high-level DCS protocols. This paper presents some of the benefits and risks of combining high-level DCS communications with low-level "field bus" communications on the same network, and describes measures taken at SNS to promote compatibility between devices connected to the control system network.

  9. Research on Community Structure in Bus Transport Networks

    International Nuclear Information System (INIS)

    Yang Xuhua; Wang Bo; Sun Youxian

    2009-01-01

    We abstract the bus transport networks (BTNs) to two kinds of complex networks with space L and space P methods respectively. Using improved community detecting algorithm (PKM agglomerative algorithm), we analyze the community property of two kinds of BTNs graphs. The results show that the BTNs graph described with space L method have obvious community property, but the other kind of BTNs graph described with space P method have not. The reason is that the BTNs graph described with space P method have the intense overlapping community property and general community division algorithms can not identify this kind of community structure. To overcome this problem, we propose a novel community structure called N-depth community and present a corresponding community detecting algorithm, which can detect overlapping community. Applying the novel community structure and detecting algorithm to a BTN evolution model described with space P, whose network property agrees well with real BTNs', we get obvious community property. (general)

  10. Foothill Transit Battery Electric Bus Demonstration Results: Second Report

    Energy Technology Data Exchange (ETDEWEB)

    Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jeffers, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2017-06-28

    This report summarizes results of a battery electric bus (BEB) evaluation at Foothill Transit, located in the San Gabriel and Pomona Valley region of Los Angeles County, California. Foothill Transit is collaborating with the California Air Resources Board and the U.S. Department of Energy's (DOE's) National Renewable Energy Laboratory to evaluate its fleet of Proterra BEBs in revenue service. The focus of this evaluation is to compare performance of the BEBs to that of conventional technology and to track progress over time toward meeting performance targets. This project has also provided an opportunity for DOE to conduct a detailed evaluation of the BEBs and charging infrastructure. This is the second report summarizing the results of the BEB demonstration at Foothill Transit and it provides data on the buses from August 2015 through December 2016. Data are provided on a selection of compressed natural gas buses as a baseline comparison.

  11. Autonomous Navigation and Obstacle Avoidance of a Micro-Bus

    Directory of Open Access Journals (Sweden)

    Carlos Fernández

    2013-04-01

    Full Text Available At present, the topic of automated vehicles is one of the most promising research areas in the field of Intelligent Transportation Systems (ITS. The use of automated vehicles for public transportation also contributes to reductions in congestion levels and to improvements in traffic flow. Moreover, electrical public autonomous vehicles are environmentally friendly, provide better air quality and contribute to energy conservation. The driverless public transportation systems, which are at present operating in some airports and train stations, are restricted to dedicated roads and exhibit serious trouble dynamically avoiding obstacles in the trajectory. In this paper, an electric autonomous mini-bus is presented. All datasets used in this article were collected during the experiments carried out in the demonstration event of the 2012 IEEE Intelligent Vehicles Symposium that took place in Alcalá de Henares (Spain. The demonstration consisted of a route 725 metres long containing a list of latitude-longitude points (waypoints. The mini-bus was capable of driving autonomously from one waypoint to another using a GPS sensor. Furthermore, the vehicle is provided with a multi-beam Laser Imaging Detection and Ranging (LIDAR sensor for surrounding reconstruction and obstacle detection. When an obstacle is detected in the planned path, the planned route is modified in order to avoid the obstacle and continue its way to the end of the mission. On the demonstration day, a total of 196 attendees had the opportunity to get a ride on the vehicles. A total of 28 laps were successfully completed in full autonomous mode in a private circuit located in the National Institute for Aerospace Research (INTA, Spain. In other words, the system completed 20.3 km of driverless navigation and obstacle avoidance.

  12. Indonesian commercial bus drum brake system temperature model

    International Nuclear Information System (INIS)

    Wibowo, D. B.; Haryanto, I.; Laksono, N. P.

    2016-01-01

    Brake system is the most significant aspect of an automobile safety. It must be able to slow the vehicle, quickly intervening and reliable under varying conditions. Commercial bus in Indonesia, which often stops suddenly and has a high initial velocity, will raise the temperature of braking significantly. From the thermal analysis it is observed that for the bus with the vehicle laden mass of 15 tons and initial velocity of 80 km/h the temperature is increasing with time and reaches the highest temperature of 270.1 °C when stops on a flat road and reaches 311.2 °C on a declination road angle, ø, 20°. These temperatures exceeded evaporation temperature of brake oil DOT 3 and DOT 4. Besides that, the magnitude of the braking temperature also potentially lowers the friction coefficient of more than 30%. The brakes are pressed repeatedly and high-g decelerations also causes brake lining wear out quickly and must be replaced every 1 month as well as the emergence of a large thermal stress which can lead to thermal cracking or thermal fatigue crack. Brake fade phenomenon that could be the cause of many buses accident in Indonesia because of the failure of the braking function. The chances of accidents will be even greater when the brake is worn and not immediately replaced which could cause hot spots as rivets attached to the brake drum and brake oil is not changed for more than 2 years that could potentially lower the evaporation temperature because of the effect hygroscopic.

  13. Indonesian commercial bus drum brake system temperature model

    Science.gov (United States)

    Wibowo, D. B.; Haryanto, I.; Laksono, N. P.

    2016-03-01

    Brake system is the most significant aspect of an automobile safety. It must be able to slow the vehicle, quickly intervening and reliable under varying conditions. Commercial bus in Indonesia, which often stops suddenly and has a high initial velocity, will raise the temperature of braking significantly. From the thermal analysis it is observed that for the bus with the vehicle laden mass of 15 tons and initial velocity of 80 km/h the temperature is increasing with time and reaches the highest temperature of 270.1 °C when stops on a flat road and reaches 311.2 °C on a declination road angle, ø, 20°. These temperatures exceeded evaporation temperature of brake oil DOT 3 and DOT 4. Besides that, the magnitude of the braking temperature also potentially lowers the friction coefficient of more than 30%. The brakes are pressed repeatedly and high-g decelerations also causes brake lining wear out quickly and must be replaced every 1 month as well as the emergence of a large thermal stress which can lead to thermal cracking or thermal fatigue crack. Brake fade phenomenon that could be the cause of many buses accident in Indonesia because of the failure of the braking function. The chances of accidents will be even greater when the brake is worn and not immediately replaced which could cause hot spots as rivets attached to the brake drum and brake oil is not changed for more than 2 years that could potentially lower the evaporation temperature because of the effect hygroscopic.

  14. Real-time bus location monitoring using Arduino

    Science.gov (United States)

    Ibrahim, Mohammad Y. M.; Audah, Lukman

    2017-09-01

    The Internet of Things (IoT) is the network of objects, such as a vehicles, mobile devices, and buildings that have electronic components, software, and network connectivity that enable them to collect data, run commands, and be controlled through the Internet. Controlling physical items from the Internet will increase efficiency and save time. The growing number of devices used by people increases the practicality of having IoT devices on the market. The IoT is also an opportunity to develop products that can save money and time and increase work efficiency. Initially, they need more efficiency for real-time bus location systems, especially in university campuses. This system can easily find the accurate locations of and distances between each bus stop and the estimated time to reach a new location. This system has been separated into two parts, which are the hardware and the software. The hardware parts are the Arduino Uno and the Global Positioning System (GPS), while Google Earth and GpsGate are the software parts. The GPS continuously takes input data from the satellite and stores the latitude and longitude values in the Arduino Uno. If we want to track the vehicle, we need to send the longitude and latitude as a message to the Google Earth software to convert these into maps for navigation. Once the Arduino Uno is activated, it takes the last received latitude and longitude positions' values from GpsGate and sends a message to Google Earth. Once the message has been sent to Google Earth, the current location will be shown, and navigation will be activated automatically. Then it will be broadcast using ManyCam, Google+ Hangouts, and YouTube, as well as Facebook, and appear to users. The additional features use Google Forms for determining problems faced by students, who can also take immediate action against the responsible department. Then after several successful simulations, the results will be shown in real time on a map.

  15. Indonesian commercial bus drum brake system temperature model

    Energy Technology Data Exchange (ETDEWEB)

    Wibowo, D. B., E-mail: rmt.bowo@gmail.com; Haryanto, I., E-mail: ismoyo2001@yahoo.de; Laksono, N. P., E-mail: priyolaksono89@gmail.com [Mechanical Engineering Dept., Faculty of Engineering, Diponegoro University (Indonesia)

    2016-03-29

    Brake system is the most significant aspect of an automobile safety. It must be able to slow the vehicle, quickly intervening and reliable under varying conditions. Commercial bus in Indonesia, which often stops suddenly and has a high initial velocity, will raise the temperature of braking significantly. From the thermal analysis it is observed that for the bus with the vehicle laden mass of 15 tons and initial velocity of 80 km/h the temperature is increasing with time and reaches the highest temperature of 270.1 °C when stops on a flat road and reaches 311.2 °C on a declination road angle, ø, 20°. These temperatures exceeded evaporation temperature of brake oil DOT 3 and DOT 4. Besides that, the magnitude of the braking temperature also potentially lowers the friction coefficient of more than 30%. The brakes are pressed repeatedly and high-g decelerations also causes brake lining wear out quickly and must be replaced every 1 month as well as the emergence of a large thermal stress which can lead to thermal cracking or thermal fatigue crack. Brake fade phenomenon that could be the cause of many buses accident in Indonesia because of the failure of the braking function. The chances of accidents will be even greater when the brake is worn and not immediately replaced which could cause hot spots as rivets attached to the brake drum and brake oil is not changed for more than 2 years that could potentially lower the evaporation temperature because of the effect hygroscopic.

  16. Work ability and stress in a bus transportation company in Belo Horizonte, Brazil.

    Science.gov (United States)

    Sampaio, Rosana Ferreira; Coelho, Cecília Martins; Barbosa, Fábio Bonfim; Mancini, Marisa Cotta; Parreira, Verônica Franco

    2009-01-01

    Demographic, occupational and psychosocial characteristics affect the health and occupational performance of workers. The objective of the present study was to elaborate a profile of the work ability and factors that affect it in a bus transportation company in Belo Horizonte, Brazil. The instruments used included a socio-demographic and occupational questionnaire, the Work Ability Index and the Job Stress Scale. Demographic information revealed that 85.7% of the 126 employees of the company were active workers, 98% were males, with an average of 39 years of age (SD= 10) and 79 months working in the company (SD= 68); more than half reported having a low schooling level. In terms of personal habits, 88% were exposed to one or more risk factors, especially a sedentary lifestyle. The average strain value (as a consequence of stress) was 0.78 (SD= 0.2) and 75.3% reported episodes of violence at the workplace. The work ability was good to excellent among 89% of the workers. Results from the logistic regression analysis showed that strain was the only significant variable in relation to the Work Ability Index, (estimated odds ratio of 0.02). The results suggest that psychosocial factors presented the greatest association with work ability, and preventive and/or corrective measures should be implemented.

  17. Study on emission characteristics of hybrid bus under driving cycles in typical Chinese city

    Science.gov (United States)

    Xie, Yongdong; Xu, Guangju

    2017-09-01

    In this study, hybrid city bus was taken as the research object, through the vehicle drum test, the vehicle emissions of hybrid bus, the transient emissions of gas pollutants, as well as the particle size and number distribution were surveyed. The results of the studies are listed as follows: First, compared to traditional fuel bus, hybrid bus could reduce about 44% of the NOx emissions, 33% of the total hydrocarbon emissions, and 51% of the particles emissions. Furthermore, the distribution of particles number concentration of test vehicle became high in middle and low in both sides. More specifically, the particle number concentration was mainly concentrated in the range from 0.021 to 0.755μm, the maximum was 0.2μm, and particle size of particulate matter (PM) less than 1.2μm accounted for 95% of the total number concentration. Particulate mass concentration was increased with increment of particle size, and the maximum of particulate mass (PM) concentration was 6.2μm. On average, whether traditional fuel bus or hybrid bus, the particle size of particulate matter(PM) less than 2.5μm accounted for more than 98% in the particles emission. It is found that the particles are more likely to deposit to the lung, respiratory bronchioles and alveoli, causing respiratory and lung diseases. Therefore, how to control the PM emissions of hybrid bus is the key factor of the study.

  18. COMPARISON OF PARALLEL AND SERIES HYBRID POWERTRAINS FOR TRANSIT BUS APPLICATION

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Zhiming [ORNL; Daw, C Stuart [ORNL; Smith, David E [ORNL; Jones, Perry T [ORNL; LaClair, Tim J [ORNL; Parks, II, James E [ORNL

    2016-01-01

    The fuel economy and emissions of both conventional and hybrid buses equipped with emissions aftertreatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicate that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar CO and HC tailpipe emissions but were also predicted to have reduced NOx tailpipe emissions compared to the conventional bus in higher speed cycles. For the New York bus cycle (NYBC), which has the lowest average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus, while the parallel hybrid bus had significantly lower tailpipe emissions. All three bus powertrains were found to require periodic active DPF regeneration to maintain PM control. Plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed due to the relatively large battery capacity that is typical of the series hybrid configuration.

  19. Performance Analysis of Trans-Jakarta Bus Suburban Service Move-Across Greater Jakarta

    Science.gov (United States)

    Tangkudung, ESW; Widyadayinta, C.

    2018-03-01

    Trans-Jakarta have developed their services scope as Suburban Service or Feeder move-across service that operate from greater Jakarta into Jakarta central vice versa. One of the route is Ciputat – Bundaran Hotel Indonesia (Tosari) and integrated with corridor 1 (one) and 8 (eight). This service is not travel on the exclusive lane or bus-way. Objective of Government Jakarta to provide this service is to decrease private car to enter the central of Jakarta. The objective of this study is to find the performance of the service. Survey have conducted static and dynamic on work day to get variable of travel time and delay, waiting time of passenger at the bus stop, headway and ridership of the bus. Service Standard Minimum of Trans-Jakarta have compared with the result of variable headway, travel speed, and waiting time at bus stop as concern of all the passengers. Analysis use correlation test method and linear regression model have done. The performance of Trans-Jakarta bus suburban service, based on travel speed indicator is fairly bad, only 8.1% of trip could comply with Minimum Service Standard. Bus performance based on the indicator of density in the bus is good, where all points are below the maximum limit i.e. 8 people/m2 at peak hour and 5 people/m2 at off-peak hour.

  20. Cloud computing-based energy optimization control framework for plug-in hybrid electric bus

    International Nuclear Information System (INIS)

    Yang, Chao; Li, Liang; You, Sixiong; Yan, Bingjie; Du, Xian

    2017-01-01

    Considering the complicated characteristics of traffic flow in city bus route and the nonlinear vehicle dynamics, optimal energy management integrated with clustering and recognition of driving conditions in plug-in hybrid electric bus is still a challenging problem. Motivated by this issue, this paper presents an innovative energy optimization control framework based on the cloud computing for plug-in hybrid electric bus. This framework, which includes offline part and online part, can realize the driving conditions clustering in offline part, and the energy management in online part. In offline part, utilizing the operating data transferred from a bus to the remote monitoring center, K-means algorithm is adopted to cluster the driving conditions, and then Markov probability transfer matrixes are generated to predict the possible operating demand of the bus driver. Next in online part, the current driving condition is real-time identified by a well-trained support vector machine, and Markov chains-based driving behaviors are accordingly selected. With the stochastic inputs, stochastic receding horizon control method is adopted to obtain the optimized energy management of hybrid powertrain. Simulations and hardware-in-loop test are carried out with the real-world city bus route, and the results show that the presented strategy could greatly improve the vehicle fuel economy, and as the traffic flow data feedback increases, the fuel consumption of every plug-in hybrid electric bus running in a specific bus route tends to be a stable minimum. - Highlights: • Cloud computing-based energy optimization control framework is proposed. • Driving cycles are clustered into 6 types by K-means algorithm. • Support vector machine is employed to realize the online recognition of driving condition. • Stochastic receding horizon control-based energy management strategy is designed for plug-in hybrid electric bus. • The proposed framework is verified by simulation and hard

  1. Optimization of transit bus fleet's life cycle assessment impacts with alternative fuel options

    International Nuclear Information System (INIS)

    Ercan, Tolga; Zhao, Yang; Tatari, Omer; Pazour, Jennifer A.

    2015-01-01

    Public transportation is one of the most promising transportation modes to reduce the environmental emissions of the transportation sector in the U.S. In order to mitigate the environmental impacts brought by the transit bus system, new energy buses are introduced into the vehicle market. The goal of this study is to find an optimal bus fleet combination for different driving conditions to minimize life cycle cost, greenhouse gas emissions, and conventional air pollutant emission impacts. For this purpose, a Multi-Objective Linear Programming approach is used to select the optimum bus fleet combinations. Given different weight scenarios, this method could effectively provide solutions for decision makers with various budget constraints or emission reduction requirements. The results indicate that in heavily congested driving cycles such as the Manhattan area, the battery electric bus is the dominant vehicle type, while the hybrid bus has more balanced performances in most scenarios because of its lower initial investment comparing to battery electric buses. Petroleum powered buses have seldom been selected by the model. The trade-off analysis shows that the overall greenhouse gas impact performance is sensitive to the life cycle cost after certain points, which could provide valuable information for the bus fleet combination planning. - Highlights: • Hybrid-Life Cycle Assessment analysis approach for transit bus operations. • Optimizing the economic and sustainability impacts of transit bus fleet operation. • CO 2 emissions and other air pollutants related health and environmental damage cost. • Trade-offs between CO 2 emissions and cost of transit bus fleet operation.

  2. Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus: Third Evaluation Report and Appendices

    Energy Technology Data Exchange (ETDEWEB)

    Chandler, K.; Eudy, L.

    2010-01-01

    This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The prototype fuel cell bus was manufactured by Van Hool and ISE Corp. and features an electric hybrid drive system with a UTC Power PureMotion 120 Fuel Cell Power System and ZEBRA batteries for energy storage. The fuel cell bus started operation in April 2007, and evaluation results through October 2009 are provided in this report.

  3. A descriptive study on public transport user behaviour from Live Bus Arrivals

    OpenAIRE

    Dell’Amico, M.; Hadjidimitriou, S.; Kaparias, I.

    2014-01-01

    In order to offer public transport that meet citizens’ needs for transport and further increase the use of bus services, Public Authorities need to analyse and understand travellers behaviour. Automatic Vehicle Location (AVL) data provide information on the observed time of arrival and departure of a bus at each stop. These data are fed into an algorithm to provide information to users on the expected time of arrival at the bus stop by an on-line service. In the city of London this service is...

  4. On the road : non-fossil fuel deployment for the public bus fleet of Sweden

    OpenAIRE

    Xylia, Maria; Silveira, Semida

    2015-01-01

    The public transport sector in Sweden has set a target to run 90% of its total vehicle-kilometers on renewable fuels by 2020, and double its market share in the long term. The focus of this paper is the adoption of renewable fuels in public bus fleets. Data for all 21 Swedish counties were gathered and analyzed, mapping the bus fleets’ condition in relation to renewable fuel deployment, CO2 emissions and energy efficiency. The main factors affecting fuel choices in the bus fleets were investi...

  5. Level of Bus Performance Based On the Relationship Between Distance and Travel Time of Universiti Tun Hussein Onn Malaysia (UTHM Bus Services

    Directory of Open Access Journals (Sweden)

    Prasetijo Joewono

    2017-01-01

    Full Text Available UTHM bus service is an important transport mode for most students at Universiti Tun Hussein Onn because it such primary public vehicle to support students movements around the campus, within and outside student apartments. This service is often associated with the quality of service in terms of time, stops and comforts. Therefore, this following study is focused on investigation on several UTHM bas routes which was based on bas operations such as distance and travel time/travel distance that would determine the level of service provided. Primary data were collected mainly to obtain information relate to speed, bas position, time movement/circulations of bus and time headway. These were obtained by installing GPS-Slute Gear i-trail along bus travels. In addition, additional data were collected by exploring previous studies regarding to the bus services such as Highway Capacity Manual (HCM 2010. The approach used was based on assessment of progress used to determine the level of quest service and such obstacle frequently occurs with results on bus delays, volume of unequal that can be overcome according to the assessments that have been provided.

  6. Get Smart About Energy: Office of Building Technology, State and Community Programs (OBT) EnergySmart Schools Program Folder (Revision)

    Energy Technology Data Exchange (ETDEWEB)

    2002-02-01

    While improving their energy use in buildings and bus fleets, schools are likely to create better places for teaching and learning with better lighting, temperature control, acoustics, and air quality. Smart districts also realize benefits in student performance.

  7. Get Smart About Energy: Office of Building Technology, State and Community Programs (OBT) EnergySmart Schools Program Brochure

    Energy Technology Data Exchange (ETDEWEB)

    Energy Smart Schools Team

    2001-10-11

    While improving their energy use in buildings and bus fleets, schools are likely to create better places for teaching and learning with better lighting, temperature control, acoustics, and air quality. Smart districts also realize benefits in student performance.

  8. Get Smart About Energy: Office of Building Technology, State and Community Programs (OBT) EnergySmart Schools Program Brochure

    International Nuclear Information System (INIS)

    Energy Smart Schools Team

    2001-01-01

    While improving their energy use in buildings and bus fleets, schools are likely to create better places for teaching and learning with better lighting, temperature control, acoustics, and air quality. Smart districts also realize benefits in student performance

  9. School Transportation Issues, Laws and Concerns: Implications for Future Administrators

    Science.gov (United States)

    Durick, Jody M.

    2010-01-01

    Nearly all building administrators are confronted with a variety of transportation issues. Challenges, concerns and questions can arise from various aspects, including student misbehaviors, transportation laws and its implications at the school level, to importance and implementation of a school bus safety program. As new and upcoming future…

  10. Perceptions of Crisis Management in a K-12 School District

    Science.gov (United States)

    Tucker, Joy

    2012-01-01

    This multiple-case qualitative study was conducted to examine the perceptions of community members, students, and staff regarding school crisis management following a 2006 tornado and 2010 bus accident in a small rural school district in Missouri. Online surveys were collected from 66 participants, and 10 follow-up interviews were completed with…

  11. Risk factors associated with bus accident severity in the United States: A generalized ordered logit model

    DEFF Research Database (Denmark)

    Kaplan, Sigal; Prato, Carlo Giacomo

    2012-01-01

    of 2011. Method: The current study investigates the underlying risk factors of bus accident severity in the United States by estimating a generalized ordered logit model. Data for the analysis are retrieved from the General Estimates System (GES) database for the years 2005–2009. Results: Results show...... that accident severity increases: (i) for young bus drivers under the age of 25; (ii) for drivers beyond the age of 55, and most prominently for drivers over 65 years old; (iii) for female drivers; (iv) for very high (over 65 mph) and very low (under 20 mph) speed limits; (v) at intersections; (vi) because......Introduction: Recent years have witnessed a growing interest in improving bus safety operations worldwide. While in the United States buses are considered relatively safe, the number of bus accidents is far from being negligible, triggering the introduction of the Motor-coach Enhanced Safety Act...

  12. Analysis of Journey to Work Travel Behavior by Car and Bus in the Sydney Metropolitan Region

    Directory of Open Access Journals (Sweden)

    Suthanaya P.A.

    2011-01-01

    Full Text Available Car dependence is a fundamental problem in the sustainability of cities with low-density suburban sprawl. Increasing the use of public transport is one of the policy objectives commonly adopted to overcome this problem. It is essential to study journey to work travel behavior by car and bus. This paper applied preference function to analyze travel behavior and Moran’s I spatial statistic to evaluate the spatial association. The results indicated that the commuting preferences of residents have moved towards distance maximization. In general, bus was preferred for shorter distance trips whilst car was preferred for longer distance trips. Unlike car, by increasing distances from the Central Business District, residents tended to use bus for shorter distance trip. A significant positive spatial association was identified for both the slope preferences by car and bus where zones with a preference towards longer or shorter trips tended to travel to zones with similar preferences.

  13. Exploring public bus service quality in South Africa: A structural equation modelling approach

    Directory of Open Access Journals (Sweden)

    Ayanda M. Vilakazi

    2014-07-01

    Full Text Available This study, which is a deviation from the usual practice of using SERVQUAL or an adaptedversion thereof, uses McKnight, Pagano and Paaswell’s (1986 service quality dimensions,namely reliability; extent of service; comfort; safety; and affordability (RECSA and structuralequation modelling to determine commuters’ perception of public bus service quality in amajor city in South Africa. The RECSA model was adapted and fitted to the data collectedfrom a convenience sample of bus commuters in Johannesburg, using structural equationmodelling. It was ascertained that reliability, service, comfort and safety influenced thepublic bus commuters’ perception of the overall service quality. The implications of theaforementioned findings for providers of public bus services are explained.

  14. City of Fresno peer exchange on bus rapid transit : a TPCB peer exchange

    Science.gov (United States)

    2013-09-11

    This report highlights key recommendations and best practices identified at the peer exchange on Bus Rapid Transit (BRT), held on May 21 and May 22, 2013, in Fresno, California. This event was sponsored by the Transportation Planning Capacity Buildin...

  15. Outsourcing of Defense Supply Center, Columbus, Bus and Taxi Service Operations

    National Research Council Canada - National Science Library

    Granetto, Paul

    1999-01-01

    Introduction. We performed the audit in response to allegations to the Defense Hotline that the Defense Supply Center, Columbus, outsourcing study for bus and taxi service operations was based on incorrect methodology...

  16. State and Federal project development procedures for bus rapid transit : managing differences and reducing implementation delays

    Science.gov (United States)

    2011-08-01

    This report documents an investigation into the transportation project development process in the : context of the implementation of bus rapid transit systems on the State Highway System as well as such : systems being part of the Federal New Starts ...

  17. NREL Showcases Hydrogen Internal Combustion Engine Bus, Helps DOE Set Standards for Outreach (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2010-11-01

    This fact sheet describes the National Renewable Energy Laboratory's (NREL's) accomplishments in showcasing a Ford hydrogen-powered internal combustion engine (H2ICE) bus at The Taste of Colorado festival in Denver. NREL started using its U.S. Department of Energy-funded H2ICE bus in May 2010 as the primary shuttle vehicle for VIP visitors, members of the media, and new employees. In September 2010, NREL featured the bus at The Taste of Colorado. This was the first major outreach event for the bus. NREL's educational brochure, vehicle wrap designs, and outreach efforts serve as a model for other organizations with DOE-funded H2ICE buses. Work was performed by the Hydrogen Education Group and Market Transformation Group in the Hydrogen Technologies and Systems Center.

  18. Preliminary concept for statewide intercity bus and rail transit system : priority corridor ranking and analysis.

    Science.gov (United States)

    2009-03-01

    This product summarizes the preliminary concept and priority corridors for development of a potential : statewide intercity bus and rail network. The concept is based upon the results of Tasks 1 through 5 of Texas : Department of Transportation Proje...

  19. State of bus safety in the U.S. : summary of federal and state regulations.

    Science.gov (United States)

    2014-06-01

    This report provides a comprehensive overview of transit bus safety regulations and standards developed by all 50 states, as well as : information on how state departments of transportation (DOT) regulate the maintenance or operation of transit/parat...

  20. Modeling and Simulation of Bus Dispatching Policy for Timed Transfers on Signalized Networks

    Science.gov (United States)

    Cho, Hsun-Jung; Lin, Guey-Shii

    2007-12-01

    The major work of this study is to formulate the system cost functions and to integrate the bus dispatching policy with signal control. The integrated model mainly includes the flow dispersion model for links, signal control model for nodes, and dispatching control model for transfer terminals. All such models are inter-related for transfer operations in one-center transit network. The integrated model that combines dispatching policies with flexible signal control modes can be applied to assess the effectiveness of transfer operations. It is found that, if bus arrival information is reliable, an early dispatching decision made at the mean bus arrival times is preferable. The costs for coordinated operations with slack times are relatively low at the optimal common headway when applying adaptive route control. Based on such findings, a threshold function of bus headway for justifying an adaptive signal route control under various time values of auto drivers is developed.

  1. 75 FR 2583 - Over-the-Road Bus Accessibility Program Grants

    Science.gov (United States)

    2010-01-15

    ... complying with DOT's over- the-road bus accessibility regulation. The authorizing legislation calls for..., 915 Chicago, IL 60606, Tel. 312-353- Second Avenue, Suite 3142, 2789. Seattle, WA 98174-1002, Tel. 206...

  2. Annoyance evaluation and the effect of noise on the health of bus drivers

    Directory of Open Access Journals (Sweden)

    Portela S Bruno

    2013-01-01

    Full Text Available In the present study, we evaluated annoyance and the effects of noise on the health of bus drivers. For that, 200 bus drivers from a public transport company participated in a cross-sectional study. Annoyance and effects on health was measured with analog scale: Sleep quality, occurrence of tinnitus, headache, irritation, and annoyance from bus engine, traffic, and passengers. Data of age and working time of bus drivers also were obtained. For noise exposure, LA eq was evaluated in 80 buses. Statistical analysis consisted of mean, standard deviation, minimum, and maximum, Kruskal-Wallis test with post-hoc Dunn, one-way ANOVA with post-hoc Tukey and Spearman′s correlation coefficient. Results indicate three groups of bus drivers (not annoyed: (N.A., a little annoyed (L.A. and highly annoyed (H.A.. The group H.A. was younger and with less working time in relation to others, with a significant difference only for age. Regarding sleep quality, there was no significant difference. For results on the occurrence of tinnitus, headache and irritation after work, group H.A. had significantly higher means. Result of annoyance to the bus engine was significantly higher in H.A. than in L.A. and N.A. Annoyance to traffic and passengers, no significant differences were found, but the highest results were found for L.A., followed by H.A. and N.A. Equivalent sound pressure level in buses was above of the limit for occupational comfort. It was concluded that bus drivers has considerable level of noise annoyance and some health effects are perceived. The noise is a factor discomfort ergonomic that may cause effects on health of bus drivers. This study aims to evaluate annoyance and the effects of noise on the health of bus drivers. Cross-sectional study with buses and bus drivers. For that, 200 bus drivers from a public transport company participated in a cross-sectional study. Annoyance and effects on health was measured with analog scale: Sleep quality

  3. Individual and population intake fractions of diesel particulate matter (DPM) in bus stop microenvironments

    International Nuclear Information System (INIS)

    Xu, Jia; Jin, Taosheng; Miao, Yaning; Han, Bin; Gao, Jiajia; Bai, Zhipeng; Xu, Xiaohong

    2015-01-01

    Diesel particulate matter (DPM) is associated with adverse human health effects. This study aims to investigate the relationship between DPM exposure and emissions by estimating the individual intake fraction (iF_i) and population intake fraction (iF_p) of DPM. Daily average concentrations of particulate matter at two bus stops during rush hours were measured, and then they were apportioned to DPM due to heavy-duty diesel bus emissions using Chemical Mass Balance Model. The DPM emissions of diesel buses for different driving conditions (idling, creeping and traveling) were estimated on the basis of field observations and published emission factors. The median iF_i of DPM was 0.67 and 1.39 per million for commuters standing at the bus stop and pedestrians/cyclists passing through the bus stop during rush hours, respectively. The median iF_p of DPM was 94 per million. Estimations of iF_i and iF_p of DPM are potentially significant for exposure assessment and risk management. - Highlights: • Methods to estimate the individual and population intake fraction in bus stop microenvironments were established. • Source apportionment was performed to estimate the DPM due to diesel bus emissions in bus stop microenvironments. • The DPM emission in bus stop microenvironments rather than in the entire urban area was considered. • The movement of people and their exposure duration were introduced in the estimation of population intake fraction. - This work established a method to estimate the individual and population intake fraction in transportation microenvironments on the basis of PM source apportionment.

  4. Bavarian liquid hydrogen bus demonstration project - safety, licensing and acceptability aspects

    Energy Technology Data Exchange (ETDEWEB)

    Wurster, R.; Knorr, H.; Pruemm, W.

    1999-07-01

    A regular 12 m city bus of the MAN SL 202 type with an internal combustion engine adapted to hydrogen operation and auxiliary gasoline operation was demonstrated in the Bavarian cities of Erlangen and Munich between April 1996 and August 1998. Three bus operators, Erlanger Stadtwerke, Stadtwerke Muenchen and Autobus Oberbayern were testing the bus in three different operating schemes. In order to be able to perform this worldwide first public demonstration of a liquid hydrogen (LH{sub 2}) city bus in regular service, several requirements with respect to safety, licensing, training and acceptability had to be fulfilled. These activities were focusing mainly on the hydrogen specific issues such as (a) integration of onboard LH{sub 2} storage vessels, piping and instrumentation, (b) implementation of storage and refueling infrastructure in the operators' yards, (c) adaptation of the maintenance garages, (d) training of operating and maintenance personnel. During phase II of the demonstration activity a poll was performed on passengers traveling onboard the hydrogen-powered city bus in order to determined the level of acceptance among the users of the bus. The bus was designed and manufactured by MAN Nutzfahrzeuge Aktiengesellschaft. The cryogenic fuel storage and the refueling equipment were designed and manufactured by Linde AG. The realization of the hardware was financially supported by the European Commission (EC) within the Euro-Quebec Hydro-Hydrogen Pilot Project. The demonstration phase was financially supported by EC and the Bavarian State Government. Ludwig-Boelkow-Systemtechnik performed project monitoring for both funding organizations. The presentation will summarize the most important results of this demonstration phase and will address the measures undertaken in order to get the bus, the refueling infrastructure and the maintenance and operating procedures approved by the relevant authorities.

  5. The impact of bus drivers ’ lifestyle on the occurrence of health problems and absenteeism

    Directory of Open Access Journals (Sweden)

    Andrej Jerman

    2016-06-01

    Full Text Available Research Question: Do bus drivers’ lifestyles affect the occurrence of health problems and absenteeism? Purpose: The purpose of the study was to determine whether the lifestyle of professional bus drivers affects the occurrence of health problems and the phenomenon of absenteeism. Method: A quantitative research method was used in the research. Data were collected using a structured questionnaire, on a sample of 230 professional bus drivers from different bus transport companies in Slovenia. Selected data were analyzed with chi-square test and multiple regression analysis. Results: We determined that there is a relationship between the state of health of professional bus drivers and participation in sport activity and that there is a statistically significant impact of lifestyle on the absenteeism of professional bus drivers. Organization: The study points to the necessity of management’s awareness to improve the conditions for the health status of employees and, consequently, absenteeism. Managers need to be more vigilant in ensuring conditions and social security that will allow employees a higher quality lifestyle. Society: The poor quality lifestyle of professional bus drivers, which includes different addictions, inadequate physical activity, and poor working conditions, is a significant factor causing absenteeism. All these factors influence the onset of negative consequences, such as the direct cost of compensation payments, costs of replacing the absent person, a reduction in productivity, which in turn affect economic growth and the high cost of health care. Originality: This is the first focus group study of professional bus drivers that targets lifestyle and its connection to absenteeism. Limitations/Future Research: The main limitation of the study is the number of respondents. The reason for this is that professional drivers are less responsive in the survey and that the study was conducted only in Slovenia, country of two

  6. Telemetry Standards, RCC Standard 106-17. Chapter 8. Digital Data Bus Acquisition Formatting Standard

    Science.gov (United States)

    2017-07-01

    incorrect word count/message and illegal mode codes are not considered bus errors. 8.6.2 Source Signal The source of data is a signal conforming to...Telemetry Standards, RCC Standard 106-17 Chapter 8, July 2017 CHAPTER 8 Digital Data Bus Acquisition Formatting Standard Acronyms...check FCS frame check sequence HDDR high-density digital recording MIL-STD Military Standard msb most significant bit PCM pulse code modulation

  7. Shelter from the Storm: Optimizing Distribution of Bus Stop Shelters in Los Angeles

    OpenAIRE

    Law, Philip; Taylor, Brian D.

    2010-01-01

    The functions of bus stop shelters and factors affecting their placement at stops in transit systems are analyzed. Drawing on information from a variety of sources, current shelter placement policy in Los Angeles was found to be guided principally by the revenue-generating potential of shelter advertisements, secondarily by political concerns over geographic equity, and only peripherally on the basis of bus stop use. Using data on shelter and stop locations, boardings, and headways, a methodo...

  8. Driving Behavior Analysis through CAN Bus Data in an Uncontrolled Environment

    OpenAIRE

    Fugiglando, Umberto; Massaro, Emanuele; Santi, Paolo; Milardo, Sebastiano; Abida, Kacem; Stahlmann, Rainer; Netter, Florian; Ratti, Carlo

    2017-01-01

    Cars can nowadays record several thousands of signals through the CAN bus technology and potentially provide real-time information on the car, the driver and the surrounding environment. This paper proposes a new method for the analysis and classification of driver behavior using a selected subset of CAN bus signals, specifically gas pedal position, brake pedal pressure, steering wheel angle, steering wheel momentum, velocity, RPM, frontal and lateral acceleration. Data has been collected in ...

  9. Design of Bus Protocol Intelligent Initiation System Based On RS485

    Directory of Open Access Journals (Sweden)

    Li Liming

    2017-01-01

    Full Text Available In order to design an effective and reliable RS485 bus protocol based on RS485 bus, this paper introduces the structure and transmission mode of the command frame and the response frame, and also introduce four control measures and the communication in order to process quality of this system. The communication protocol is open, tolerant, reliable and fast, and can realize ignition more reliable and accurate in the intelligent initiation system.

  10. Exploring public bus service quality in South Africa: A structural equation modelling approach

    OpenAIRE

    Ayanda M. Vilakazi; Krishna K. Govender

    2014-01-01

    This study, which is a deviation from the usual practice of using SERVQUAL or an adaptedversion thereof, uses McKnight, Pagano and Paaswell’s (1986) service quality dimensions,namely reliability; extent of service; comfort; safety; and affordability (RECSA) and structuralequation modelling to determine commuters’ perception of public bus service quality in amajor city in South Africa. The RECSA model was adapted and fitted to the data collectedfrom a convenience sample of bus commuters in Joh...

  11. [Injuries sustained by bus passengers in the municipality of Odense 1996-1999].

    Science.gov (United States)

    Barsi, T; Faergemann, C; Larsen, L B

    2001-10-22

    Owing to several recent bus-related accidents in Denmark, we wished to investigate injuries sustained by passengers. From our ongoing registration of patients treated in the casualty department at Odense University Hospital, we identified all residents of Odense Municipality who had sustained injuries as bus passengers from 1996 to 1999. Market analysis and demographic information were used to calculate the incidence and risk. Over this four-year period, 327 consecutive injuries had been sustained by 246 bus passengers, 72 men and 174 women, mean ages 44 and 53 years. The incidence rate was 3.3 injured per 10,000 inhabitants per year, with no increasing tendency during the study period. The risk was 2.2 injured per 1,000,000 bus passengers per year, highest in women and increasing with age. Injuries most frequently occurred when the bus stopped (31%), as passengers were boarding or alighting (23%), or during collision with another vehicle (20%). Most commonly injured areas were the lower (30%) and upper (28%) extremities and the head or neck (27%). Contusions and sprains were the most common injuries (59%). The most common fractures were those of the humerus and hip region. Bus passenger injuries are not a growing problem. The incidence increases with age.

  12. Evaluating the Impacts of Bus Fare on Social Equity Based on IC Card Data in China

    Directory of Open Access Journals (Sweden)

    Shaowu Cheng

    2016-10-01

    Full Text Available Bus fare equity has attracted significant attention in China in the past few years. Compared with developed countries, China’s intelligent transportation systems are in their infancy, with immature bus fare policies being used in many public transit systems. The methods used for evaluating public transit fare equity in developed countries compare different fare policies based on rich data and cannot be directly applied in developing countries like China. In this paper, we present a method that uses IC card data, bus-mounted GPS data, and relevant statistical yearbook data to evaluate the equity of flat bus fare. The method ranks the factors that influence the impacts of bus fare on social equity for different passenger groups and indicates that trip distance and passenger boarding time are the two primary factors for bus fare equity from a resource allocation perspective. Finally, we present a case study that evaluates the flat fare policy for route 204 in Suzhou using the proposed method. The results show that the proposed method is feasible.

  13. An observational comparison of the older and younger bus passenger experience in a developing world city.

    Science.gov (United States)

    Aceves-González, Carlos; May, Andrew; Cook, Sharon

    2016-06-01

    This study was an unobtrusive observational analysis of 333 older and younger bus passengers in Guadalajara, Mexico. A set of data were collected for each observed passenger, as well as more general observations related to driver behaviour, bus design and bus service characteristics. There were significant differences between older and younger passengers in terms of boarding and alighting times, use of handrails, seat location preferences, passenger stability and coping strategies in order to maintain postural stability. The conditions of travel are conducive to a poor passenger experience for the older passengers in particular. Although the problems may be attributed to bus design and driver behaviour typical of that in developing countries, they are also influenced by the wider transport infrastructure, and a lack of a regulatory regime which places drivers under time pressure and in direct competition with each other. Practitioner Summary: Bus services must cater for all ages of passengers, including the elderly. This unobtrusive observational study investigated the passenger experience in a developing world city. Bus and wider service design were found to compromise the journey experience, with the older users being particularly negatively impacted. Design recommendations are provided.

  14. Bus Travel Time Deviation Analysis Using Automatic Vehicle Location Data and Structural Equation Modeling

    Directory of Open Access Journals (Sweden)

    Xiaolin Gong

    2015-01-01

    Full Text Available To investigate the influences of causes of unreliability and bus schedule recovery phenomenon on microscopic segment-level travel time variance, this study adopts Structural Equation Modeling (SEM to specify, estimate, and measure the theoretical proposed models. The SEM model establishes and verifies hypotheses for interrelationships among travel time deviations, departure delays, segment lengths, dwell times, and number of traffic signals and access connections. The finally accepted model demonstrates excellent fitness. Most of the hypotheses are supported by the sample dataset from bus Automatic Vehicle Location system. The SEM model confirms the bus schedule recovery phenomenon. The departure delays at bus terminals and upstream travel time deviations indeed have negative impacts on travel time fluctuation of buses en route. Meanwhile, the segment length directly and negatively impacts travel time variability and inversely positively contributes to the schedule recovery process; this exogenous variable also indirectly and positively influences travel times through the existence of signalized intersections and access connections. This study offers a rational approach to analyzing travel time deviation feature. The SEM model structure and estimation results facilitate the understanding of bus service performance characteristics and provide several implications for bus service planning, management, and operation.

  15. EtherBone - A Network Layer for the Wishbone SoC Bus

    CERN Document Server

    Kreider, M; Lewis, J; Włostowski, T; Serrano, J

    2011-01-01

    Today, there are several System on a Chip (SoC) bus systems. Typically, these buses are confined on-chip and rely on higher level components to communicate with the outside world. Taking these systems a step further, we see the possibility of extending the reach of the SoC bus to remote FPGAs or processors. This leads to the idea of the EtherBone (EB) core, which connects a Wishbone (WB) Ver. 4 Bus via a Gigabit Ethernet based network link to remote peripheral devices. EB acts as a transparent interconnect module towards attached WB Bus devices. Address information and data from one or more WB bus cycles is preceded with a descriptive header and encapsulated in a UDP/IP packet. Because of this standard compliance, EB is able to traverse Wide Area Networks and is therefore not bound to a geographic location. Due to the low level nature of the WB bus, EB provides a sound basis for remote hardware tools like a JTAG debugger, In-System-Programmer (ISP), boundary scan interface or logic analyser module. EB was de...

  16. ETHERBONE - a network layer for the wishbone SoC bus

    International Nuclear Information System (INIS)

    Kreider, M.; Terpstra, W.; Lewis, J.; Serrano, J.; Wlostowski, T.

    2012-01-01

    Today, there are several System on a Chip (SoC) bus systems. Typically, these buses are confined on-chip and rely on higher level components to communicate with the outside world. Taking these systems a step further, we see the possibility of extending the reach of the SoC bus to remote FPGAs or processors. This leads to the idea of the EtherBone (EB) core, which connects a Wishbone (WB) Ver. 4 Bus via a Gigabit Ethernet based network link to remote peripheral devices. EB acts as a transparent interconnect module towards attached WB Bus devices. Address information and data from one or more WB bus cycles is preceded with a descriptive header and encapsulated in a UDP/IP packet. Because of this standard compliance, EB is able to traverse Wide Area Networks and is therefore not bound to a geographic location. Due to the low level nature of the WB bus, EB provides a sound basis for remote hardware tools like a JTAG debugger, In-System-Programmer (ISP), boundary scan interface or logic analyser module. EB was developed in the scope of the White-Rabbit Timing Project (WR) at CERN and GSI/FAIR, which employs GigaBit Ethernet technology to communicate with memory mapped slave devices. WR will make use of EB as means to issue commands to its timing nodes and control connected accelerator hardware. (authors)

  17. An interconnecting bus power optimization method combining interconnect wire spacing with wire ordering

    International Nuclear Information System (INIS)

    Zhu Zhang-Ming; Hao Bao-Tian; En Yun-Fei; Yang Yin-Tang; Li Yue-Jin

    2011-01-01

    On-chip interconnect buses consume tens of percents of dynamic power in a nanometer scale integrated circuit and they will consume more power with the rapid scaling down of technology size and continuously rising clock frequency, therefore it is meaningful to lower the interconnecting bus power in design. In this paper, a simple yet accurate interconnect parasitic capacitance model is presented first and then, based on this model, a novel interconnecting bus optimization method is proposed. Wire spacing is a process for spacing wires for minimum dynamic power, while wire ordering is a process that searches for wire orders that maximally enhance it. The method, i.e., combining wire spacing with wire ordering, focuses on bus dynamic power optimization with a consideration of bus performance requirements. The optimization method is verified based on various nanometer technology parameters, showing that with 50% slack of routing space, 25.71% and 32.65% of power can be saved on average by the proposed optimization method for a global bus and an intermediate bus, respectively, under a 65-nm technology node, compared with 21.78% and 27.68% of power saved on average by uniform spacing technology. The proposed method is especially suitable for computer-aided design of nanometer scale on-chip buses. (interdisciplinary physics and related areas of science and technology)

  18. Evaluation of Effective Factors on Travel Time in Optimization of Bus Stops Placement Using Genetic Algorithm

    Science.gov (United States)

    Bargegol, Iraj; Ghorbanzadeh, Mahyar; Ghasedi, Meisam; Rastbod, Mohammad

    2017-10-01

    In congested cities, locating and proper designing of bus stops according to the unequal distribution of passengers is crucial issue economically and functionally, since this subject plays an important role in the use of bus system by passengers. Location of bus stops is a complicated subject; by reducing distances between stops, walking time decreases, but the total travel time may increase. In this paper, a specified corridor in the city of Rasht in north of Iran is studied. Firstly, a new formula is presented to calculate the travel time, by which the number of stops and consequently, the travel time can be optimized. An intended corridor with specified number of stops and distances between them is addressed, the related formulas to travel time are created, and its travel time is calculated. Then the corridor is modelled using a meta-heuristic method in order that the placement and the optimal distances of bus stops for that are determined. It was found that alighting and boarding time along with bus capacity are the most effective factors affecting travel time. Consequently, it is better to have more concentration on indicated factors for improving the efficiency of bus system.

  19. Optimal Design of the Feeder-Bus Network Based on the Transfer System

    Directory of Open Access Journals (Sweden)

    Lianbo Deng

    2013-01-01

    Full Text Available This paper studied the classic feeder-bus network design problem (FBNDP, which can be described as follows: for the passenger travel demand between rail stations and bus stops on a given urban transit network, it designs the optimal feeder bus routes and frequencies so as to minimize the passengers’ travel expense and the operator’s cost. We extended the demand pattern of M-to-1 in most existing researches to M-to-M. We comprehensively considered the passenger travel cost, which includes the waiting and riding cost on the bus, riding cost on rail, and transfer cost between these two transportation modes, and presented a new genetic algorithm that determines the optimal feeder-bus operating frequencies under strict constraint conditions. The numerical examples under different demand patterns have been experienced and analysed, which showed the robustness and efficiency of the presented algorithm. We also found that the distribution pattern of the travel demand has a significant influence on the feeder-bus network construction.

  20. Modelling modal shift due to the enhanced level of bus service

    Directory of Open Access Journals (Sweden)

    P. Vedagiri

    2009-06-01

    Full Text Available This study is concerned with the estimation of the probable shift of auto-rickshaw (three wheeled motorized para-transit vehicle users to the bus due to an increase in its level of service after providing exclusive bus lanes on Indian city roads carrying heterogeneous traffic. The quantum of an increase in the level of bus service due to the introduction of an exclusive bus lane was determined using a recently developed simulation model of heterogeneous traffic flow. The data on other factors (variables that might cause modal shift from the auto-rickshaw to the bus was collected conducting a home-interview survey based on the stated preference approach. A binary logit model of mode-choice was then calibrated using the collected data and the model was also validated using a holdout sample. A mode-choice probability curve to depict the possible shift of auto-rickshaw users to the bus is developed taking difference in the travel times of two-modes as the basis to serve as a user friendly tool to analyze the possible modal shift for a wide range of the values of the involved variables.