Faktor – Faktor yang Berhubungan dengan Safety Driving pada Pengemudi Bus Ekonomi Trayek Semarang – Surabaya di Terminal Terboyo Semarang

OpenAIRE

Paasetya, Avendika Bagoes; Kurnaiwan, Bina; Wahyuni, Ida

2016-01-01

Safety driving is an effective way to reduce the incidence of accidents due to driver inattention while driving. In Indonesia, the cause of most accidents are caused by human error, which reached 90%. Traffic accidents are one of the safety risks to the driver economi bus which lasts for 24 hours a day.This study aims to identify the factors of related safety driving on driver bus economic class route Semarang – Surabaya in Terboyo terminal Semarang. This type of research is analytic survey w...

How to Reduce Those Costly School Bus Accidents.

Science.gov (United States)

Farmer, Ernest

1985-01-01

The deterrent to school bus accidents is preparedness. Training programs for drivers and mechanics, equipment specifications, and a community support base are some of the ways to prevent tragedy. (MLF)

Implementation of a Walking School Bus: Lessons Learned

Science.gov (United States)

Kong, Alberta S.; Sussman, Andrew L.; Negrete, Sylvia; Patterson, Nissa; Mittleman, Rachel; Hough, Richard

2009-01-01

Background: Obesity is rapidly becoming the most common chronic medical condition affecting children. To address this crisis, an Albuquerque, New Mexico, elementary school partnered with University of New Mexico researchers and conducted a Walking School Bus (WSB). The purpose of this article is to examine the feasibility of implementing a WSB.…

Characterisation of an urban bus network for environmental purposes.

Science.gov (United States)

André, Michel; Villanova, André

2004-12-01

Since pollutant emissions are closely related to the operating conditions of vehicles, their evaluation usually involves studying these operating conditions (through bus instrumentation and monitoring under actual operation), the design of representative driving or engine test cycles and the measurement of pollutant emissions. A preliminary characterisation of the routes on a bus network should make it possible to identify typical routes, the driving conditions and pollutant emissions of which are then studied. Two approaches are envisaged and applied to the Paris area, for which a wealth of information is available, which should be transferable to other bus networks. Both approaches are based on factorial analysis and automatic clustering, to allow optimum description and the identification of a pertinent typology of the bus routes in several classes. The first attempt at characterisation is based on statistics relating to bus operations: route characteristics (length, dedicated bus lanes, number of stops, location of stops: schools, tourist sites, hospitals, railways or underground stations), travel time, commercial speed, annual statistics (number of passengers, number of vehicles per hour, total kilometres), the irregularity of travel (variation of travel times, injuries, congestion.), as well as information on the problems encountered (congestion, distribution of the passenger load, junctions, bends). A second approach is based on the analysis of the "urban context" in which buses are driven. Population, employment, housing, road network, traffic and places that generate or disturb traffic (schools, railway stations, shopping areas, etc.) are calculated for the Ile de France region, by cells of 100 x 100 m, and collected in a geographical information system (GIS). Statistical analyses enable a typology of these urban cells to be established, the main parameters being density, type of housing, road types and traffic levels. The bus routes are then analysed

High-Tech School Bus Teaches Students on the Road

Science.gov (United States)

Katims, Lauren

2011-01-01

Last year, kindergarten through high school students in the rural Hector, Arkansas, School District barely had the technology resources that keep kids interested in math and science. This year, they potentially have the most advanced resources in the country--before they even step into the classroom. One school bus in Arkansas' Pope County has…

Improving School Bus Safety. Transportation Research Board Special Report 222.

Science.gov (United States)

National Academy of Sciences - National Research Council, Washington, DC. Transportation Research Board.

While school buses transport more passengers per trip, the rate of occupant fatalities per mile driven for school buses is one-quarter that for passenger cars. Nevertheless, the public expects school districts and other school bus operators to take all reasonable precautions to protect children as they travel to and from school. Although a variety…

School bus pollution and changes in the air quality at schools: a case study.

Science.gov (United States)

Li, Chunlei; Nguyen, Quyen; Ryan, Patrick H; Lemasters, Grace K; Spitz, Henry; Lobaugh, Megan; Glover, Samuel; Grinshpun, Sergey A

2009-05-01

Millions of children attending US schools are exposed to traffic-related air pollutants, including health-relevant ultrafine aerosols generated from school buses powered with diesel fuel. This case study was established in a midwestern (USA) metropolitan area to determine the concentration and elemental composition of aerosol in the vicinity of a public school during morning hours when the bus traffic in and out of the adjacent depot was especially intense. Simultaneous measurements were performed at a control site. The ambient aerosol was first characterized in real time using a particle size selective aerosol spectrometer and then continuously monitored at each site with a real-time non-size-selective instrument that detected particles of 20 nm to >1 microm. In addition, air samples were collected with PM2.5 Harvard Impactors and analyzed for elemental composition using the X-ray fluorescence technique (for 38 elements) and thermal-optical transmittance (for carbon). The measurements were conducted during two seasons: in March at ambient temperature around 0 degrees C and in May when it ranged mostly between 10 and 20 degrees C. The particle number concentration at the test site exhibited high temporal variability while it was time independent at the control site. Overall, the aerosol particle count at the school was 4.7 +/- 1.0 times (March) and 2.2 +/- 0.4 times (May) greater than at the control site. On some days, a 15 min-averaged particle number concentration showed significant correlation with the number of school bus arrivals and departures during these time intervals. On other days, the correlation was less than statistically significant. The 3 h time-averaged particle concentrations determined in the test site on days when the school buses operated were found to be more than two-fold greater (on average) than those measured on bus-free days at the same location, and this difference was statistically significant. Overall, the data suggest a possible

GeoBus: bringing Earth science learning to secondary schools in the UK

Science.gov (United States)

Robinson, Ruth; Roper, Kathryn; Pike, Charlotte

2015-04-01

GeoBus (www.geobus.org.uk) is an educational outreach project that was developed in 2012 by the Department of Earth and Environmental Sciences at the University of St Andrews, and it is sponsored jointly by industry and the UK Research Councils (NERC and EPSRC). The aims of GeoBus are to support the teaching of Earth Science in secondary (middle and high) schools by providing teaching support to schools that have no or little expertise of teaching Earth science, to share the outcomes of new science research and the experiences of young researchers with school pupils, and to provide a bridge between industry, higher education institutions, research councils and schools. Since its launch, GeoBus has visited over 160 different schools across the length and breadth of Scotland. Almost 35,000 pupils will have been involved in experiential Earth science learning activities by April 2015, including many in remote and disadvantaged regions. The challenge with secondary school experiential learning as outreach is that activities need to be completed in either 50 or 80 minutes to fit within the school timetables in the UK, and this can limit the amount of hands-on activities that pupils undertake in one session. However, it is possible to dedicate a whole or half day of linked activities to Earth science learning within the Scotland Curriculum for Excellence, and this provides a long enough period to undertake field work, conduct group projects, or complete more complicated experiments. GeoBus has developed a suite of workshops that all involve experiential learning and are targeted for shorter and longer time slots, and the lessons learned in developing and refining these workshops to maximise the learning achieved will be presented. A key aim of GeoBus is to incorporate research outcomes directly into workshops, and to involve early career researchers in project development. One example that is currently in progress is a set of hydrology workshops that focus on the water

Simulating Study on Drive System Performance for Hybrid Electric Bus Based on ADVISOR

Directory of Open Access Journals (Sweden)

Wang Xingxing

2017-01-01

Full Text Available Hybrid electric bus has a number of advantages when compared with ordinary passenger cars, but in the dynamic matching and the vehicle performance are difficult to detect, thus limits its development process. In this paper, combined with the actual models, the hybrid electric bus module parameters were modified in the software of ADVISOR (Advanced Vehicle Simulator, main including: module of the vehicle, the wheel module, motor module, a battery module and engine module, three kinds of bus models for A, B and C were established, and the related performance that need to be analyzed was set up, such as acceleration, gradability, emissions and energy utilization and so on, in order to ensure the vehicle running in the same environment and convenient for comparison, a fixed vehicle driving cycles was chose, then the simulation results was analyzed, and the various performance was compared with the dynamic indicators and economic indicators which determined by referencing of traditional city bus standard and each other, and finally, the performance optimal model of B was chose out which can meet the demand, its related performance parameters of the simulation results are as follows: the best gradability is 26%, maximum speed is 72.7km/h, maximum acceleration is 1.7m/s2, 0~50km/h acceleration time is 9.5s and fuel consumption is 25L/km.

Walking school bus programs in U.S. public elementary schools.

Science.gov (United States)

Turner, Lindsey; Chriqui, Jamie F; Chaloupka, Frank J

2013-07-01

Active transportation to school provides an important way for children to meet physical activity recommendations. The "walking school bus" (WSB) is a strategy whereby adults walk with a group of children to and from school along a fixed route. This study assessed whether school-organized WSB programs varied by school characteristics, district policies, and state laws. School data were gathered by mail-back surveys in nationally representative samples of U.S. public elementary schools during the 2008-2009 and 2009-2010 school years (n = 632 and 666, respectively). Corresponding district policies and state laws were obtained. Nationwide, 4.2% of schools organized a WSB program during 2008-2009, increasing to 6.2% by 2009-2010. Controlling for demographic covariates, schools were more likely to organize a WSB program where there was a strong district policy pertaining to safe active routes to school (OR = 2.14, P law requiring crossing guards around schools (OR = 2.72, P laws are associated with an increased likelihood of elementary schools organizing these programs. Policymaking efforts may encourage schools to promote active transportation.

School Bus Transportation of Children With Special Health Care Needs.

Science.gov (United States)

O'Neil, Joseph; Hoffman, Benjamin D

2018-05-01

School systems are responsible for ensuring that children with special needs are safely transported on all forms of federally approved transportation provided by the school system. A plan to provide the most current and proper support to children with special transportation needs should be developed by the Individualized Education Program team, including the parent, school transportation director, and school nurse, in conjunction with physician orders and recommendations. With this statement, we provide current guidance for the protection of child passengers with specific health care needs. Guidance that applies to general school transportation should be followed, inclusive of staff training, provision of nurses or aides if needed, and establishment of a written emergency evacuation plan as well as a comprehensive infection control program. Researchers provide the basis for recommendations concerning occupant securement for children in wheelchairs and children with other special needs who are transported on a school bus. Pediatricians can help their patients by being aware of guidance for restraint systems for children with special needs and by remaining informed of new resources. Pediatricians can also play an important role at the state and local level in the development of school bus specifications. Copyright © 2018 by the American Academy of Pediatrics.

GeoBus: bringing experiential Earth science learning to secondary schools in the UK

Science.gov (United States)

Pike, C. J.; Robinson, R. A. J.; Roper, K. A.

2014-12-01

GeoBus (www.geobus.org.uk) is an educational outreach project that was developed in 2012 by the Department of Earth and Environmental Sciences at the University of St Andrews, and it is sponsored jointly by industry and the UK Research Councils (NERC and EPSRC). The aims of GeoBus are to support the teaching of Earth Science in secondary (middle and high) schools by providing teaching support to schools that have no or little expertise of teaching Earth science, to share the outcomes of new science research and the experiences of young researchers with school pupils, and to provide a bridge between industry, higher education institutions, research councils and schools. Since its launch, GeoBus has visited over 160 different schools across the length and breadth of Scotland. Over 30,000 pupils will have been involved in experiential Earth science learning activities by December 2014, including many in remote and disadvantaged regions. The challenge with secondary school experiential learning as outreach is that activities need to be completed in either 50 or 80 minutes to fit within the school timetables in the UK, and this can limit the amount of hands-on activities that pupils undertake in one session. However, it is possible to dedicate a whole or half day of linked activities to Earth science learning in Scotland and this provides a long enough period to undertake field work, conduct group projects, or complete more complicated experiments. GeoBus has developed a suite of workshops that all involve experiential learning and are targeted for shorter and longer time slots, and the lessons learned in developing and refining these workshops to maximise the learning achieved will be presented. Three potentially unsurprising observations hold true for all the schools that GeoBus visits: young learners like to experiment and use unfamiliar equipment to make measurements, the element of competition stimulates learners to ask questions and maintain focus and enthusiasum

Performance of school bus retrofit systems: ultrafine particles and other vehicular pollutants.

Science.gov (United States)

Zhang, Qunfang; Zhu, Yifang

2011-08-01

This study evaluated the performance of retrofit systems for diesel-powered school buses, a diesel oxidation catalyst (DOC) muffler and a spiracle crankcase filtration system (CFS), regarding ultrafine particles (UFPs) and other air pollutants from tailpipe emissions and inside bus cabins. Tailpipe emissions and in-cabin air pollutant levels were measured before and after retrofitting when the buses were idling and during actual pick-up/drop off routes. Retrofit systems significantly reduced tailpipe emissions with a reduction of 20-94% of total particles with both DOC and CFS installed. However, no unequivocal decrease was observed for in-cabin air pollutants after retrofitting. The AC/fan unit and the surrounding air pollutant concentrations played more important roles for determining the in-cabin air quality of school buses than did retrofit technologies. Although current retrofit systems reduce children's exposure while waiting to board at a bus station, retrofitting by itself does not protect children satisfactorily from in-cabin particle exposures. Turning on the bus engine increased in-cabin UFP levels significantly only when the wind blew from the bus' tailpipe toward its hood with its windows open. This indicated that wind direction and window position are significant factors determining how much self-released tailpipe emissions may penetrate into the bus cabin. The use of an air purifier was found to remove in-cabin particles by up to 50% which might be an alternative short-to-medium term strategy to protect children's health.

Iterated Local Search Algorithm with Strategic Oscillation for School Bus Routing Problem with Bus Stop Selection

Directory of Open Access Journals (Sweden)

Mohammad Saied Fallah Niasar

2017-02-01

Full Text Available he school bus routing problem (SBRP represents a variant of the well-known vehicle routing problem. The main goal of this study is to pick up students allocated to some bus stops and generate routes, including the selected stops, in order to carry students to school. In this paper, we have proposed a simple but effective metaheuristic approach that employs two features: first, it utilizes large neighborhood structures for a deeper exploration of the search space; second, the proposed heuristic executes an efficient transition between the feasible and infeasible portions of the search space. Exploration of the infeasible area is controlled by a dynamic penalty function to convert the unfeasible solution into a feasible one. Two metaheuristics, called N-ILS (a variant of the Nearest Neighbourhood with Iterated Local Search algorithm and I-ILS (a variant of Insertion with Iterated Local Search algorithm are proposed to solve SBRP. Our experimental procedure is based on the two data sets. The results show that N-ILS is able to obtain better solutions in shorter computing times. Additionally, N-ILS appears to be very competitive in comparison with the best existing metaheuristics suggested for SBRP

Stress-related psychosocial factors at work, fatigue, and risky driving behavior in bus rapid transport (BRT) drivers.

Science.gov (United States)

Useche, Sergio A; Ortiz, Viviola Gómez; Cendales, Boris E

2017-07-01

There is consistent scientific evidence that professional drivers constitute an occupational group that is highly exposed to work related stressors. Furthermore, several recent studies associate work stress and fatigue with unsafe and counterproductive work behaviors. This study examines the association between stress-related work conditions of Bus Rapid Transport (BRT) drivers and risky driving behaviors; and examines whether fatigue is a mechanism that mediates the association between the two. A sample of 524 male Bus Rapid Transit (BRT) operators were drawn from four transport companies in Bogotá, Colombia. The participants answered a survey which included an adapted version of the Driver Behavior Questionnaire (DBQ) for BRT operators, as well as the Effort-Reward Imbalance and Job Content Questionnaires, the Subjective Fatigue subscale of the Checklist Individual Strength (CIS) and the Need for Recovery after Work Scale (NFR). Utilizing Structural Equation Models (SEM) it was found that risky driving behaviors in BRT operators could be predicted through job strain, effort-reward imbalance and social support at work. It was also found that fatigue and need for recovery fully mediate the associations between job strain and risky driving, and between social support and risky driving, but not the association between effort/reward imbalance (ERI) and risky driving. The results of this study suggest that a) stress related working conditions (Job Strain, Social Support and ERI) are relevant predictors of risky driving in BRT operators, and b) that fatigue is the mechanism which links another kind of stress related to working conditions (job strain and low social support) with risky driving. The mechanism by which ERI increases risky driving in BRT operators remains unexplained. This research suggests that in addition to the individual centered stress-reduction occupational programs, fatigue management interventions aimed to changing some working conditions may reduce

Cloud computing-based energy optimization control framework for plug-in hybrid electric bus

International Nuclear Information System (INIS)

Yang, Chao; Li, Liang; You, Sixiong; Yan, Bingjie; Du, Xian

2017-01-01

Considering the complicated characteristics of traffic flow in city bus route and the nonlinear vehicle dynamics, optimal energy management integrated with clustering and recognition of driving conditions in plug-in hybrid electric bus is still a challenging problem. Motivated by this issue, this paper presents an innovative energy optimization control framework based on the cloud computing for plug-in hybrid electric bus. This framework, which includes offline part and online part, can realize the driving conditions clustering in offline part, and the energy management in online part. In offline part, utilizing the operating data transferred from a bus to the remote monitoring center, K-means algorithm is adopted to cluster the driving conditions, and then Markov probability transfer matrixes are generated to predict the possible operating demand of the bus driver. Next in online part, the current driving condition is real-time identified by a well-trained support vector machine, and Markov chains-based driving behaviors are accordingly selected. With the stochastic inputs, stochastic receding horizon control method is adopted to obtain the optimized energy management of hybrid powertrain. Simulations and hardware-in-loop test are carried out with the real-world city bus route, and the results show that the presented strategy could greatly improve the vehicle fuel economy, and as the traffic flow data feedback increases, the fuel consumption of every plug-in hybrid electric bus running in a specific bus route tends to be a stable minimum. - Highlights: • Cloud computing-based energy optimization control framework is proposed. • Driving cycles are clustered into 6 types by K-means algorithm. • Support vector machine is employed to realize the online recognition of driving condition. • Stochastic receding horizon control-based energy management strategy is designed for plug-in hybrid electric bus. • The proposed framework is verified by simulation and hard

The GeoBus project: a mobile Earth science outreach project for secondary schools in the UK

Science.gov (United States)

Robinson, R. A.; Roper, K. A.; Macfarlane, D.; Pike, C.

2013-12-01

GeoBus is an educational outreach project that was developed in 2012 by the Department of Earth and Environmental Sciences at the University of St Andrews. It is sponsored jointly by industry and the UK Research Councils (NERC and EPSRC). The aims of GeoBus are to support the teaching of Earth Science in secondary (high) schools by providing teaching resources that are not readily available to educators, to inspire young learners by incorporating new science research outcomes in teaching activities, and to provide a bridge between industry, higher education institutions, research councils and schools. These linkages are important for introducing career opportunities in Earth sciences. Since its launch, GeoBus has visited over 140 different schools across the length and breadth of Scotland. Over 20,000 pupils will have been involved in practical hands-on Earth science learning activities by December 2013, including many in remote and disadvantaged regions. The resources that GeoBus brings to schools include all the materials and equipment needed to run workshops, field excursions and Enterprise Challenges. GeoBus provides 16 workshops which can be adapted for different learning levels. Workshops are 50 to 80 minute sessions for up to 30 pupils and topics include minerals, rocks, fossils, geological time, natural resources, climate change, volcanoes, earthquakes, and geological mapping. As with all GeoBus activities, the inclusion of equipment and technology otherwise unavailable to schools substantially increases the engagement of pupils in workshops. Field excursions are popular, as many teachers have little or no field trainng and feel unable to lead this type of activity. The excursions comprise half or full day sessions for up to 30 pupils and are tailored to cover the local geology or geomorphology. The Enterprise Challenges are half or full day sessions for up to 100 pupils. Current topics are Drilling for Oil, Renewable Energy, a Journey to Mars and Scotland

The School Bus Symposium: A Poetic Journey of Co-created Conference Space

Directory of Open Access Journals (Sweden)

Mitchell A McLarnon

2016-07-01

Full Text Available With the intention of disrupting and re-imagining traditional conference spaces, this article is a poetic compilation developed from a Curriculum Studies conference symposium that took place on a school bus. During the School Bus Symposium, in situ poetry writing and reading, song and storytelling occurred in response to open ended prompts and facilitation of creative activities. After the symposium, a call was issued to invite participants to submit any poetry or stories produced during, or inspired by the session. Consisting of 18 submissions including poetry, story, photography and creative essays, infused by curriculum theory and poetic inquiry, this collection offers an inclusive, reflective, participatory, and experiential rendering where participants are living and journeying poetically. Emphasizing creative engagement with personal memories, the authors collectively aimed to promote art education through imaginative approaches to curriculum studies, poetic inquiry and academic conferences.

The driving and controlling techniques of compactPCI bus in VxWorks real-time operating system

International Nuclear Information System (INIS)

Li Anzong; Ju Xiaodong; Qiao Wenxiao

2005-01-01

CompactPCI bus and interface featuring, the content and function of PCI configuration register are introduced herein. The driving and controlling techniques of CompactPCI bus in VxWorks real-time operating system are detailed. Hardware interrupt handling is one of key significance in real-time systems, because it is usually through interrupts that the system is informed of external events. VxWorks allows C functions to be connected to any interrupt. A routine connected to an interrupt in this way is called an interrupt service routine (ISR). For response of interrupt, interrupt control/status register of PCI 9054 interface chip needs to be set. The general-purpose binary semaphore used in ISR is capable of addressing the requirements of both forms of task coordination: mutual exclusion and synchronization. Therefore, the system runs stably and reliably. (authors)

A preliminary survey analysis of school shuttle bus system towards smart mobility solutions

Science.gov (United States)

Yue, Wong Seng; Hoy, Cheong Wan; Chye, Koh Keng

2017-10-01

Mobility and accessibility are crucial indicators of urban development. Public transport in the urban areas came into existence to fulfil transportation needs as well as mobility and accessibility demands. Ridership can be affected by the quality and quantity of transit service. However, technical improvements are needed for such as real-time bus information, controlling run time and headway delay. Thus, this paper is aimed to carry out a preliminary survey to determine the problems of school shuttle bus that faced by the students in a selected educational institution, their perceptions of using shuttle bus tracking and information mobile application and impacts of real-time information of public transits on bus ridership and towards smart mobility solutions. Efficient public transportation system needs further investigation about the role of mobile application for the bus tracking system in supporting smart mobility actions and real-time information. The proposed application also provides a smart solution for the management of public infrastructures and urban facilities in Malaysia in future. Eventually, this study opens an opportunity to improve Malaysian quality of life on the public value that created for the city as a whole.

The erigone bus study

International Nuclear Information System (INIS)

Durieu, L.; Vignes, M.; Wolstenholme, P.

1982-01-01

A study has been made of some factors determining the performance and cost-effectiveness of microcomputer bus systems implemented in Europa crates. An experimental system has been specified and a number of modules constructed in accordance with the specification, in order to test the validity of some of the ideas proposed. It has been demonstrated that the bus interfacing logic can be simple and inexpensive, while maintaining a high degree of processor independence and also a high degree of transparency in operation. The number of pins required by the bus is minimized by multiplexing address and data. A series termination for the drive of the multiplexed lines permits cross-talk to be reduced to insignificant levels: this technique is recommended for wider application. The experimental bus is proposed as a basis for the construction of simple microcomputer-based instrumentation systems. (orig.)

Analysis of a diesel-electric hybrid urban bus system

Science.gov (United States)

Marr, W. W.; Sekar, R. R.; Ahlheim, M. C.

A hybrid bus powered by a diesel engine and a battery pack was analyzed over an idealized bus-driving cycle in Chicago. Three hybrid configurations, two parallel and one series, were evaluated. The results indicate that the fuel economy of a hybrid bus, taking into account the regenerative braking, is comparable with that of a conventional diesel bus. Life-cycle costs are slightly higher because of the added weight and cost of the battery.

49 CFR 571.221 - Standard No. 221, School bus body joint strength.

Science.gov (United States)

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Standard No. 221, School bus body joint strength. 571.221 Section 571.221 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR VEHICLE SAFETY STANDARDS Federal Motor Vehicle Safety Standard...

Analysis and Suppression of Zero Sequence Circulating Current in Open Winding PMSM Drives With Common DC Bus

OpenAIRE

Zhan, H.; Zhu, Z.Q.; Odavic, M.

2017-01-01

In this paper, the zero sequence circulating current in open winding permanent magnet synchronous machine (OW-PMSM) drives with common dc bus is systematically analyzed for the first time. It is revealed that the zero sequence circulating current is affected by zero sequence back-electromotive force, cross coupling voltages in zero sequence from the machine side, pulse-width modulation induced zero sequence voltage, and inverter nonlinearity from the inverter side. Particularly, the influence...

Work stress, fatigue and risk behaviors at the wheel: Data to assess the association between psychosocial work factors and risky driving on Bus Rapid Transit drivers

Directory of Open Access Journals (Sweden)

Sergio Useche

2017-12-01

Full Text Available This Data in Brief (DiB article presents a hierarchical multiple linear regression model that examine the associations between psychosocial work factors and risk behaviors at the wheel in Bus Rapid Transit (BRT drivers (n=524. The data were collected using a structured self-administrable questionnaire made of measurements of wok stress (job strain and effort- reward imbalance, fatigue (need for recovery and chronic fatigue, psychological distress and demographics (professional driving experience, hours driven per day and days working per week. The data contains 4 parts: descriptive statistics, bivariate correlations between the study variables and a regression model predicting risk behaviors at the wheel and the entire study dataset. For further information, it is convenient to read the full article entitled “Stress-related Psychosocial Factors at Work, Fatigue, and Risky Driving Behavior in Bus Rapid Transport (BRT Drivers”, published in Accident Analysis & Prevention. Keywords: Professional drivers, Work stress, Fatigue, Psychological distress, Risk behaviors, Bus Rapid Transport, BRT

Improved design of HIRFL-CSR EVME bus controller

International Nuclear Information System (INIS)

Zhao Long; Liu Wufeng; Qiao Weimin; Jing Lan

2009-01-01

The EVME bus controller which is a key component of the HIRFL-CSR control system was improved. Besides reconfiguring the embedded Linux, a utility program was developed for data exchange between the controller and the database. The bus controller is based on ARM920T(ARM9) micro processor which is BGA packaged. The bus controller has the universal interface of VGA display, keyboard, and mouse. The backboard interface logic is programmed in an in-system configurable FPGA device. The bus can drive high current up to 64 mA, with the flexibility of the programmable signal definitions. All the improved performance helped the EVME bus controller play a crucial role in HIRFL-CSR control system. (authors)

An Improved Model for Headway-Based Bus Service Unreliability Prevention with Vehicle Load Capacity Constraint at Bus Stops

Directory of Open Access Journals (Sweden)

Weiya Chen

2012-01-01

Full Text Available This paper presents an improved model for improving headway-based bus route service reliability at bus stops using real-time preventive operation control, taking into account dynamic interaction among random passenger demand, stochastic driving conditions of route segments, and vehicle load capacity constraint. In this model, the real-time information of passenger demand and vehicle operation is involved to predict the imminent unacceptable headway deviation, in the case of which some in-time preventive control strategies are deployed according to the given control rules. As a case study, a single fixed bus route with high-frequency services was simulated and different scenarios of real-time preventive operation control were performed. Headway adherence and average passenger wait time were used to measure bus service reliability. The results show that the improved model is closer to the real bus route service, and using real-time information to predict potential service unreliability and trigger in-time preventive control can reduce bus bunching and avoid big gap.

Savannah River bus project

Energy Technology Data Exchange (ETDEWEB)

Summers, W.A. [Westinghouse Savannah River Co., Aiken, SC (United States)

1998-08-01

The H2Fuel Bus is the world`s first hybrid hydrogen electric transit bus. It was developed through a public/private partnership involving several leading technology and industrial organizations in the Southeast, with primary funding and program management provided by the Department of Energy. The primary goals of the project are to gain valuable information on the technical readiness and economic viability of hydrogen buses and to enhance the public awareness and acceptance of emerging hydrogen technologies. The bus has been operated by the transit agency in Augusta, Georgia since April, 1997. It employs a hybrid IC engine/battery/electric drive system, with onboard hydrogen fuel storage based on the use of metal hydrides. Initial operating results have demonstrated an overall energy efficiency (miles per Btu) of twice that of a similar diesel-fueled bus and an operating range twice that of an all-battery powered electric bus. Tailpipe emissions are negligible, with NOx less than 0.2 ppm. Permitting, liability and insurance issues were addressed on the basis of extensive risk assessment and safety analyses, with the inherent safety characteristic of metal hydride storage playing a major role in minimizing these concerns. Future plans for the bus include continued transit operation and use as a national testbed, with potential modifications to demonstrate other hydrogen technologies, including fuel cells.

Optimal energy management for a series-parallel hybrid electric bus

International Nuclear Information System (INIS)

Xiong Weiwei; Zhang Yong; Yin Chengliang

2009-01-01

This paper aims to present a new type of series-parallel hybrid electric bus and its energy management strategy. This hybrid bus is a post-transmission coupled system employing a novel transmission as the series-parallel configuration switcher. In this paper, the vehicle architecture, transmission scheme and numerical models are presented. The energy management system governs the mode switching between the series mode and the parallel mode as well as the instantaneous power distribution. In this work, two separated controllers using fuzzy logic called Mode Decision and Parallel-driving Energy Management are employed to fulfill these two tasks. The energy management strategy and the applications of fuzzy logic are described. The strategy is validated by a forward-facing simulation program based on the software Matlab/Simulink. The results show that the energy management strategy is effective to control the engine operating in a high-efficiency region as well as to sustain the battery charge state while satisfy the drive ability. The energy consumption is theoretically reduced by 30.3% to that of the conventional bus under transit bus driving cycle. In addition, works need future study are also presented.

Creative Bus Financing.

Science.gov (United States)

Malone, Wade

1982-01-01

Alternative ways of financing school bus purchases include financing privately through contractors or commercial banks, financing through sources such as insurance companies and pension funds, leasing the buses, or contracting for transportation services. (Author/MLF)

Development of a multi-mode hybrid electric bus

Energy Technology Data Exchange (ETDEWEB)

Shemmans, M.J. [Overland Custom Coach, Thorndale, ON (Canada); Bland, C. [BET Services Inc., Mississauga, ON (Canada)

2004-04-01

This paper describes the development of an energy efficient, low floor, 28 foot hybrid electric bus for use as an airport shuttle bus or other specialized transit operations. A multi-mode concept was also adopted to include the capability of operating in battery-only drive, engine-only drive or a range of hybrid electric drive modes. The electric drivetrain was powered by a battery pack or a combination of a battery pack and an internal combustion engine-powered electric generator. The participating companies in this project include Overland Custom Coach, BET Services Inc., Siemens and Transport Canada. The technical feasibility study was described with reference to duty cycles, performance issues, vehicle weight, mechanical drive issues, brakes, suspension, powertrain cooling, heating, ventilation, electrical system, batteries and control system. The commercial feasibility was also described in terms of capital and operating costs. Results of the prototype tests validate the possibilities of zero or reduced emission transit in real world applications. 25 tabs., 32 figs.

State all-driver distracted driving laws and high school students'  texting while driving behavior.

Science.gov (United States)

Qiao, Nan; Bell, Teresa Maria

2016-01-01

Texting while driving is highly prevalent among adolescents and young adults in the United States. Texting while driving can significantly increase the risk of road crashes and is associated with other risky driving behaviors. Most states have enacted distracted driving laws to prohibit texting while driving. This study examines effects of different all-driver distracted driving laws on texting while driving among high school students. High school student data were extracted from the 2013 National Youth Risk Behavior Survey. Distracted driving law information was collected from the National Conference of State Legislatures. The final sample included 6,168 high school students above the restricted driving age in their states and with access to a vehicle. Logistic regression was applied to estimate odds ratios of laws on texting while driving. All-driver text messaging bans with primary enforcement were associated with a significant reduction in odds of texting while driving among high school students (odds ratio = 0.703; 95% confidence interval, 0.513-0.964), whereas all-driver phone use bans with primary enforcement did not have a significant association with texting while driving (odds ratio = 0.846; 95% confidence interval, 0.501-1.429). The findings indicate that all-driver distracted driving laws that specifically target texting while driving as opposed to all types of phone use are effective in reducing the behavior among high school students.

The mobile GeoBus outreach project: hands-on Earth and Mars activities for secondary schools in the UK

Science.gov (United States)

Robinson, Ruth; Pike, Charlotte; Roper, Kathryn

2015-04-01

GeoBus (www.geobus.org.uk) is an educational outreach project that was developed in 2012 by the Department of Earth and Environmental Sciences at the University of St Andrews, and it is sponsored jointly by industry and the UK Research Councils (NERC and EPSRC). The aims of GeoBus are to support the teaching of Earth Science in secondary schools by providing teaching resources that are not readily available to educators, to inspire young learners by incorporating new science research outcomes in teaching activities, and to provide a bridge between industry, higher education institutions, research councils and schools. Since its launch, GeoBus has visited over 160 different schools across the length and breadth of Scotland. Just under 35,000 pupils have been involved in practical hands-on Earth science learning activities since the project began in 2012, including many in remote and disadvantaged regions. The resources that GeoBus brings to schools include all the materials and equipment needed to run 50 - 80 minute workshops, and half- or whole-day Enterprise Challenges and field excursions. Workshops are aimed at a class of up to 30 pupils and topics include minerals, rocks, fossils, geological time, natural resources, climate change, volcanoes, earthquakes, and geological mapping. As with all GeoBus activities, the inclusion of equipment and technology otherwise unavailable to schools substantially increases the engagement of pupils in workshops. Field excursions are increasingly popular, as many teachers have little or no field trainng and feel unable to lead this type of activity. The excursions comprise half or full day sessions for up to 30 pupils and are tailored to cover the local geology or geomorphology. Enterprise Challenge are half or full day sessions for up to 100 pupils. Topics include "Journey to Mars", "Scotland's Rocks", "Drilling for Oil", and "Renewable Energy". Both of the energy Enterprise Challenges were designed to incorporates ideas and

The volume and type of unhealthy bus shelter advertising around schools in Perth, Western Australia: Results from an explorative study.

Science.gov (United States)

Parnell, Ashleigh; Edmunds, Melinda; Pierce, Hannah; Stoneham, Melissa J

2018-03-05

Exposure to advertising for unhealthy food, alcohol and gambling has been shown to influence children and adolescents' behaviours and attitudes. This exploratory study aimed to assess the volume and type of unhealthy bus shelter advertisements near schools in five local government areas in Perth, Western Australia and to monitor whether the volume of unhealthy advertisements varied seasonally. The 29 local governments in the Perth metropolitan region were contacted seeking information regarding the locations of bus shelters featuring advertisements in their local government area. Five local governments provided sufficient information for an audit of the bus shelter advertisements in their area to be conducted. Every bus shelter within 500 m of a school was photographed and the type of advertisement recorded. The advertisements in the food, non-alcoholic beverage, alcohol, or gambling categories were then classified as being healthy, moderate, or unhealthy. This process was carried out in June, September, December 2016, and March 2017 to ascertain whether the type of advertisements displayed changed depending on the season. Of the 293 advertisements recorded over the four audits, 31% featured unhealthy products, 3% moderate, and <1% healthy. Only two of the 293 advertisements were classified as being healthy. Seasonal variation in the volume of unhealthy advertisements was not identified. SO WHAT?: Western Australian school students are regularly exposed to unhealthy bus shelter advertisements. Stricter regulation of outdoor advertising is needed to ensure that young people are protected from the influence of unhealthy industries. © 2018 Australian Health Promotion Association.

Driving Behavior Analysis through CAN Bus Data in an Uncontrolled Environment

OpenAIRE

Fugiglando, Umberto; Massaro, Emanuele; Santi, Paolo; Milardo, Sebastiano; Abida, Kacem; Stahlmann, Rainer; Netter, Florian; Ratti, Carlo

2017-01-01

Cars can nowadays record several thousands of signals through the CAN bus technology and potentially provide real-time information on the car, the driver and the surrounding environment. This paper proposes a new method for the analysis and classification of driver behavior using a selected subset of CAN bus signals, specifically gas pedal position, brake pedal pressure, steering wheel angle, steering wheel momentum, velocity, RPM, frontal and lateral acceleration. Data has been collected in ...

Ecodriving for Reduction of Bus Transit Emission with Vehicle’s Hybrid Dynamic Model

Directory of Open Access Journals (Sweden)

Xiuzheng Zheng

2015-01-01

Full Text Available This paper formulates a global ecodriving optimal control to advise the green driving speed for bus transit to minimize the exhaust emission using Vehicle-to-Infrastructure (V2I communication. Assuming communication between vehicles and infrastructure (V2I and knowledge of traffic signal timings and waiting passengers at stations are known, an optimal driving speed is proposed to minimize the total vehicle emissions of the bus route. The dwell time of the bus transit at each station which includes two parts is proposed. A traffic lights timing model is employed as constraints to control the formation of the green wave band. Vehicle specific power (VSP model is further applied to evaluate the exhaust emission level linked with the speed and acceleration of the bus transit. An approximate sixteen-kilometer traffic network including fourteen intersections and fifteen stations of Beijing bus transit line 1 in Chaoyang District, Beijing, is chosen to investigate the performance of the developed ecodriving approach.

Analysis of On-Board Photovoltaics for a Battery Electric Bus and Their Impact on Battery Lifespan

Directory of Open Access Journals (Sweden)

Kevin R. Mallon

2017-07-01

Full Text Available Heavy-duty electric powertrains provide a potential solution to the high emissions and low fuel economy of trucks, buses, and other heavy-duty vehicles. However, the cost, weight, and lifespan of electric vehicle batteries limit the implementation of such vehicles. This paper proposes supplementing the battery with on-board photovoltaic modules. In this paper, a bus model is created to analyze the impact of on-board photovoltaics on electric bus range and battery lifespan. Photovoltaic systems that cover the bus roof and bus sides are considered. The bus model is simulated on a suburban bus drive cycle on a bus route in Davis, CA, USA for a representative sample of yearly weather conditions. Roof-mounted panels increased vehicle driving range by 4.7% on average annually, while roof and side modules together increased driving range by 8.9%. However, variations in weather conditions meant that this additional range was not reliably available. For constant vehicle range, rooftop photovoltaic modules extended battery cycle life by up to 10% while modules on both the roof and sides extended battery cycle life by up to 19%. Although side-mounted photovoltaics increased cycle life and range, they were less weight- and cost-effective compared to the roof-mounted panels.

Intelligent Bus Stops in the Flexible Bus Systems

Directory of Open Access Journals (Sweden)

Razi Iqbal

2014-09-01

Full Text Available The purpose of this paper is to discuss Intelligent Bus Stops in a special Demand Responsive Transit (DRT, the Flexible Bus System. These Intelligent Bus Stops are more efficient and information rich than Traditional Bus Stops. The real time synchronization of the Flexible Bus System makes it unique as compared to Traditional Bus Systems. The Main concern is to make Bus Stops intelligent and information rich. Buses are informed about the no. of passengers waiting at the upcoming Bus Stops. If there are no passengers to ride or get off on upcoming Bus Stop, the Bus can skip that Bus Stop and head towards the next Bus Stop where passenger is waiting, which will decrease the ride time of the passengers on the Bus and also the wait time of the passengers waiting on the upcoming Bus Stops. Providing more information at Bus Stops about the Destination (Time to Destination, Distance to Destination etc. and Buses (Bus Location, Arrival Time of Bus etc. makes it easier for the passengers to decide whether to ride a particular Bus or not.

A design of high-precision BLDCM drive with bus voltage protection

Science.gov (United States)

Lian, Xuezheng; Wang, Haitao; Xie, Meilin; Huang, Wei; Li, Dawei; Jing, Feng

2017-11-01

In the application of space satellite turntable, the design of balance wheel is very necessary. To solve the acquisition precision of Brushless DC motor speed is low, and the encoder is also more complex, this paper improves the original hall signal measurement methods. Using the logic device to achieve the six frequency multiplication of hall signal, the signal is used as speed feedback to achieve speed closed-loop control and improve the speed stability. At the same time, in order to prevent the E.M.F of BLDC motor to raise the voltage of the bus bar when reversing or braking, and affect the normal operation of other circuit modules, the analog circuit is used to protect the bus bar voltage by the way of energy consumption braking. The experimental results are consistent with the theoretical design, and the rationality and feasibility of the frequency multiplication scheme and bus voltage protection scheme are verified.

Braking energy regeneration control of a fuel cell hybrid electric bus

International Nuclear Information System (INIS)

Zhang, Junzhi; Lv, Chen; Qiu, Mingzhe; Li, Yutong; Sun, Dongsheng

2013-01-01

Highlights: • A braking energy regeneration system has been designed for a fuel cell bus. • Control strategy coordinating energy efficiency and brake safety is proposed. • The system and control strategy proposed are experimentally verified. • Based on test results, energy efficiency of the FCB is improved greatly. - Abstract: This paper presents the braking energy regeneration control of a fuel cell hybrid electric bus. The configuration of the regenerative braking system based on a pneumatic braking system was proposed. To recapture the braking energy and improve the fuel economy, a control strategy coordinating the regenerative brake and the pneumatic brake was designed and applied in the FCHB. Brake safety was also guaranteed by the control strategy when the bus encounters critical driving situations. Fuel economy tests were carried out under China city bus typical driving cycle. And hardware-in-the-loop tests of the brake safety of the FCHB under proposed control strategy were also accomplished. Test results indicate that the present approach provides an improvement in fuel economy of the fuel cell hybrid electric bus and guarantees the brake safety in the meantime

Study on emission characteristics of hybrid bus under driving cycles in typical Chinese city

Science.gov (United States)

Xie, Yongdong; Xu, Guangju

2017-09-01

In this study, hybrid city bus was taken as the research object, through the vehicle drum test, the vehicle emissions of hybrid bus, the transient emissions of gas pollutants, as well as the particle size and number distribution were surveyed. The results of the studies are listed as follows: First, compared to traditional fuel bus, hybrid bus could reduce about 44% of the NOx emissions, 33% of the total hydrocarbon emissions, and 51% of the particles emissions. Furthermore, the distribution of particles number concentration of test vehicle became high in middle and low in both sides. More specifically, the particle number concentration was mainly concentrated in the range from 0.021 to 0.755μm, the maximum was 0.2μm, and particle size of particulate matter (PM) less than 1.2μm accounted for 95% of the total number concentration. Particulate mass concentration was increased with increment of particle size, and the maximum of particulate mass (PM) concentration was 6.2μm. On average, whether traditional fuel bus or hybrid bus, the particle size of particulate matter(PM) less than 2.5μm accounted for more than 98% in the particles emission. It is found that the particles are more likely to deposit to the lung, respiratory bronchioles and alveoli, causing respiratory and lung diseases. Therefore, how to control the PM emissions of hybrid bus is the key factor of the study.

Intelligent Bus Stops in the Flexible Bus Systems

OpenAIRE

Razi Iqbal; Muhammad Usman Ghani

2014-01-01

The purpose of this paper is to discuss Intelligent Bus Stops in a special Demand Responsive Transit (DRT), the Flexible Bus System. These Intelligent Bus Stops are more efficient and information rich than Traditional Bus Stops. The real time synchronization of the Flexible Bus System makes it unique as compared to Traditional Bus Systems. The Main concern is to make Bus Stops intelligent and information rich. Buses are informed about the no. of passengers waiting at the upcoming ...

Risk factors affecting fatal bus accident severity: Their impact on different types of bus drivers.

Science.gov (United States)

Feng, Shumin; Li, Zhenning; Ci, Yusheng; Zhang, Guohui

2016-01-01

While the bus is generally considered to be a relatively safe means of transportation, the property losses and casualties caused by bus accidents, especially fatal ones, are far from negligible. The reasons for a driver to incur fatalities are different in each case, and it is essential to discover the underlying risk factors of bus fatality severity for different types of drivers in order to improve bus safety. The current study investigates the underlying risk factors of fatal bus accident severity to different types of drivers in the U.S. by estimating an ordered logistic model. Data for the analysis are retrieved from the Buses Involved in Fatal Accidents (BIFA) database from the USA for the years 2006-2010. Accidents are divided into three levels by counting their equivalent fatalities, and the drivers are classified into three clusters by the K-means cluster analysis. The analysis shows that some risk factors have the same impact on different types of drivers, they are: (a) season; (b) day of week; (c) time period; (d) number of vehicles involved; (e) land use; (f) manner of collision; (g) speed limit; (h) snow or ice surface condition; (i) school bus; (j) bus type and seating capacity; (k) driver's age; (l) driver's gender; (m) risky behaviors; and (n) restraint system. Results also show that some risk factors only have impact on the "young and elder drivers with history of traffic violations", they are: (a) section type; (b) number of lanes per direction; (c) roadway profile; (d) wet road surface; and (e) cyclist-bus accident. Notably, history of traffic violations has different impact on different types of bus drivers. Copyright © 2015 Elsevier Ltd. All rights reserved.

Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus: Third Evaluation Report and Appendices

Energy Technology Data Exchange (ETDEWEB)

Chandler, K.; Eudy, L.

2010-01-01

This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The prototype fuel cell bus was manufactured by Van Hool and ISE Corp. and features an electric hybrid drive system with a UTC Power PureMotion 120 Fuel Cell Power System and ZEBRA batteries for energy storage. The fuel cell bus started operation in April 2007, and evaluation results through October 2009 are provided in this report.

Determination of the Optimum Heat Transfer Coefficient and Temperature Rise Analysis for a Lithium-Ion Battery under the Conditions of Harbin City Bus Driving Cycles

Directory of Open Access Journals (Sweden)

Xiaogang Wu

2017-10-01

Full Text Available This study investigated the heat problems that occur during the operation of power batteries, especially thermal runaway, which usually take place in high temperature environments. The study was conducted on a ternary polymer lithium-ion battery. In addition, a lumped parameter thermal model was established to analyze the thermal behavior of the electric bus battery system under the operation conditions of the driving cycles of the Harbin city electric buses. Moreover, the quantitative relationship between the optimum heat transfer coefficient of the battery and the ambient temperature was investigated. The relationship between the temperature rise (Tr, the number of cycles (c, and the heat transfer coefficient (h under three Harbin bus cycles have been investigated at 30 °C, because it can provide a basis for the design of the battery thermal management system. The results indicated that the heat transfer coefficient that meets the requirements of the battery thermal management system is the cubic power function of the ambient temperature. Therefore, if the ambient temperature is 30 °C, the heat transfer coefficient should be at least 12 W/m2K in the regular bus lines, 22 W/m2K in the bus rapid transit lines, and 32 W/m2K in the suburban lines.

COMPARISON OF PARALLEL AND SERIES HYBRID POWERTRAINS FOR TRANSIT BUS APPLICATION

Energy Technology Data Exchange (ETDEWEB)

Gao, Zhiming [ORNL; Daw, C Stuart [ORNL; Smith, David E [ORNL; Jones, Perry T [ORNL; LaClair, Tim J [ORNL; Parks, II, James E [ORNL

2016-01-01

The fuel economy and emissions of both conventional and hybrid buses equipped with emissions aftertreatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicate that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar CO and HC tailpipe emissions but were also predicted to have reduced NOx tailpipe emissions compared to the conventional bus in higher speed cycles. For the New York bus cycle (NYBC), which has the lowest average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus, while the parallel hybrid bus had significantly lower tailpipe emissions. All three bus powertrains were found to require periodic active DPF regeneration to maintain PM control. Plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed due to the relatively large battery capacity that is typical of the series hybrid configuration.

Distraction 'on the buses': a novel framework of ergonomics methods for identifying sources and effects of bus driver distraction.

Science.gov (United States)

Salmon, Paul M; Young, Kristie L; Regan, Michael A

2011-05-01

Driver distraction represents a significant problem in the public transport sector. Various methods exist for investigating distraction; however, the majority are difficult to apply within the context of naturalistic bus driving. This article investigates the nature of bus driver distraction at a major Australian public transport company, including the sources of distraction present, and their effects on driver performance, through the application of a novel framework of ergonomics methods. The framework represents a novel approach for assessing distraction in a real world context. The findings suggest that there are a number of sources of distraction that could potentially distract bus drivers while driving, including those that derive from the driving task itself, and those that derive from the additional requirements associated with bus operation, such as passenger and ticketing-related distractions. A taxonomy of the sources of bus driver distraction identified is presented, along with a discussion of proposed countermeasures designed to remove the sources identified or mitigate their effects on driver performance. Copyright © 2010 Elsevier Ltd and The Ergonomics Society. All rights reserved.

School buses, air pollution and children's health : improving children's health and local air quality by reducing school bus emissions

Energy Technology Data Exchange (ETDEWEB)

Perrotta, K. [Ontario Public Health Association, Toronto, ON (Canada)

2005-11-01

The exhaust gases from school buses was examined and recommendations were presented for the establishment of a healthy school bus program in Ontario that is directed at improving children's health and local air quality. The Ontario Public Health Association is concerned with school bus emissions because they are heavy-duty vehicles that emit large quantities of diesel-related air pollutants such as fine particulate matter, nitrogen oxides and diesel particulates. In addition, school buses can be self-polluting vehicles that expose children on-board to high levels of fine particulates and diesel particulate matter. Both these pollutants have been associated with a range of acute and chronic health problems such as asthma, respiratory infections, allergies, and school absences. With nearly 800,000 Ontario children being transported on school buses annually, these exposures can represent a serious public health concern, as childhood exposures can also influence the health of exposed individuals later in life. Exposure studies have found that tailpipe and engine emissions contribute greatly to concentrations of air pollutants on-board school buses. The studies also showed that on-board concentrations were also influenced by local air quality in the communities studied, traffic density, wind direction, the configuration of windows, idling and queuing patterns. It was recommended that the use of ultra-low sulphur diesel fuel along with the installation of diesel particulate filters and closed crankcase filters can reduce the concentrations of air pollutants on-board school buses to almost ambient air levels, even under idling conditions. This report recommended the replacement of pre-1994 school buses, the retrofitting of 1994-2003 school buses with filters, and maintaining proper maintenance, idling and vehicle operation practices. refs., tabs., figs.

Optimization of transit bus fleet's life cycle assessment impacts with alternative fuel options

International Nuclear Information System (INIS)

Ercan, Tolga; Zhao, Yang; Tatari, Omer; Pazour, Jennifer A.

2015-01-01

Public transportation is one of the most promising transportation modes to reduce the environmental emissions of the transportation sector in the U.S. In order to mitigate the environmental impacts brought by the transit bus system, new energy buses are introduced into the vehicle market. The goal of this study is to find an optimal bus fleet combination for different driving conditions to minimize life cycle cost, greenhouse gas emissions, and conventional air pollutant emission impacts. For this purpose, a Multi-Objective Linear Programming approach is used to select the optimum bus fleet combinations. Given different weight scenarios, this method could effectively provide solutions for decision makers with various budget constraints or emission reduction requirements. The results indicate that in heavily congested driving cycles such as the Manhattan area, the battery electric bus is the dominant vehicle type, while the hybrid bus has more balanced performances in most scenarios because of its lower initial investment comparing to battery electric buses. Petroleum powered buses have seldom been selected by the model. The trade-off analysis shows that the overall greenhouse gas impact performance is sensitive to the life cycle cost after certain points, which could provide valuable information for the bus fleet combination planning. - Highlights: • Hybrid-Life Cycle Assessment analysis approach for transit bus operations. • Optimizing the economic and sustainability impacts of transit bus fleet operation. • CO 2 emissions and other air pollutants related health and environmental damage cost. • Trade-offs between CO 2 emissions and cost of transit bus fleet operation.

Methodology for measurement of diesel particle size distributions from a city bus working in real traffic conditions

International Nuclear Information System (INIS)

Armas, O; Gómez, A; Mata, C

2011-01-01

The study of particulate matter (PM) and nitrogen oxides emissions of diesel engines is nowadays a necessary step towards pollutant emission reduction. For a complete evaluation of PM emissions and its size characterization, one of the most challenging goals is to adapt the available techniques and the data acquisition procedures to the measurement and to propose a methodology for the interpretation of instantaneous particle size distributions (PSD) of combustion-derived particles produced by a vehicle during real driving conditions. In this work, PSD from the exhaust gas of a city bus operated in real driving conditions with passengers have been measured. For the study, the bus was equipped with a rotating disk diluter coupled to an air supply thermal conditioner (with an evaporating tube), the latter being connected to a TSI Engine Exhaust Particle Sizer spectrometer. The main objective of this work has been to propose an alternative procedure for evaluating the influence of several transient sequences on PSD emitted by a city bus used in real driving conditions with passengers. The transitions studied were those derived from the combination of four possible sequences or categories during real driving conditions: idle, acceleration, deceleration with fuel consumption and deceleration without fuel consumption. The analysis methodology used in this work proved to be a useful tool for a better understanding of the phenomena related to the determination of PSD emitted by a city bus during real driving conditions with passengers

Methodology for measurement of diesel particle size distributions from a city bus working in real traffic conditions

Science.gov (United States)

Armas, O.; Gómez, A.; Mata, C.

2011-10-01

The study of particulate matter (PM) and nitrogen oxides emissions of diesel engines is nowadays a necessary step towards pollutant emission reduction. For a complete evaluation of PM emissions and its size characterization, one of the most challenging goals is to adapt the available techniques and the data acquisition procedures to the measurement and to propose a methodology for the interpretation of instantaneous particle size distributions (PSD) of combustion-derived particles produced by a vehicle during real driving conditions. In this work, PSD from the exhaust gas of a city bus operated in real driving conditions with passengers have been measured. For the study, the bus was equipped with a rotating disk diluter coupled to an air supply thermal conditioner (with an evaporating tube), the latter being connected to a TSI Engine Exhaust Particle Sizer spectrometer. The main objective of this work has been to propose an alternative procedure for evaluating the influence of several transient sequences on PSD emitted by a city bus used in real driving conditions with passengers. The transitions studied were those derived from the combination of four possible sequences or categories during real driving conditions: idle, acceleration, deceleration with fuel consumption and deceleration without fuel consumption. The analysis methodology used in this work proved to be a useful tool for a better understanding of the phenomena related to the determination of PSD emitted by a city bus during real driving conditions with passengers.

Estimating bus passenger waiting times from incomplete bus arrivals data

OpenAIRE

McLeod, F.N.

2007-01-01

This paper considers the problem of estimating bus passenger waiting times at bus stops using incomplete bus arrivals data. This is of importance to bus operators and regulators as passenger waiting time is a key performance measure. Average waiting times are usually estimated from bus headways, that is, time gaps between buses. It is both time-consuming and expensive to measure bus arrival times manually so methods using automatic vehicle location systems are attractive; however, these syste...

Impaired-driving prevalence among US high school students: associations with substance use and risky driving behaviors.

Science.gov (United States)

Li, Kaigang; Simons-Morton, Bruce G; Hingson, Ralph

2013-11-01

We examined the prevalence of impaired driving among US high school students and associations with substance use and risky driving behavior. We assessed driving while alcohol or drug impaired (DWI) and riding with alcohol- or drug-impaired drivers (RWI) in a nationally representative sample of 11th-grade US high school students (n = 2431). We examined associations with drinking and binge drinking, illicit drug use, risky driving, and demographic factors using multivariate sequential logistic regression analysis. Thirteen percent of 11th-grade students reported DWI at least 1 of the past 30 days, and 24% reported RWI at least once in the past year. Risky driving was positively associated with DWI (odds ratio [OR] = 1.25; P phone calls (OR = 3.2) while driving. Our findings suggest the need for comprehensive approaches to the prevention of DWI, RWI, and other risky driving behavior.

Staying Safe in the Car and on the Bus

Science.gov (United States)

... a booster! Get in the Back Here's another important safety rule: Sit in the back seat. Kids 12 ... or band concerts once in a while, it's important to follow these rules. When you see the bus driving up, everyone waiting should get into a line. ...

School bus travel is associated with bullying victimization among Canadian male, but not female, middle and high school students.

Science.gov (United States)

Sampasa-Kanyinga, Hugues; Chaput, Jean-Philippe; Hamilton, Hayley A; Larouche, Richard

2016-08-01

Previous research has found a link between active school transportation and bullying victimization among school-aged children. However, the link with other school travel modes (such as car, school bus, and public transportation) and bullying victimization is largely unknown. The purpose of this study was to investigate the association between school travel mode and report of bullying victimization among Canadian middle and high school students. The sample consisted of 5065 students aged 11-20 years (mean age: 15.2±1.9 years; 56% females) who participated in the 2013 Ontario Students Drug Use and Health Survey (OSDUHS). Overall, 24.7% of students reported school bullying victimization in the past year. Females (27.2%) were more likely than males (22.3%) to be victims of school bullying (ptravel to (adjusted odd ratio (OR)=1.83; 95% confidence interval (CI)=1.25-2.68) and from (OR=1.79; 95% CI=1.70-2.67) school was associated with greater odds of bullying victimization among males, but not females. However, the use of public transportation to get to school was associated with lower odds of bullying victimization compared to active transportation among females only (OR=0.59; 95% CI=0.36-0.97). These findings suggest that school travel mode should be considered when considering risks for bullying victimization. Bullying prevention efforts should target school buses to make children's commute a safe and enjoyable experience. Copyright © 2016 Elsevier Ltd. All rights reserved.

Functional Bus Driver-Pupil Passenger Relationships.

Science.gov (United States)

Farmer, Ernest

1987-01-01

Successful school bus drivers bring much more than mechanical know-how to the job. They develop good rapport with students while acting to bring undesirable student behavior under control. Drivers must also show an interest in students' welfare and have a good sense of humor. (MLH)

Highway/Railroad Accident Report: Collision Of Northeast Illinois Regional Commuter Railroad Corporation (METRA) Train And Transportation Joint Agreement School District 47/155 School Bus At Railroad/Highway Grade Crossing In Fox River Grove, Illinois, On

Science.gov (United States)

1996-10-29

This report explains the collision of a Northeast Illinois Regional Commuter Railroad Corporation commuter train with a Transportation Joint Agreement School District 47/155 school bus that was stopped at a railroad/highway grade crossing in Fox Rive...

Energy Management Strategy Based on the Driving Cycle Model for Plugin Hybrid Electric Vehicles

Directory of Open Access Journals (Sweden)

Xiaoling Fu

2014-01-01

Full Text Available The energy management strategy (EMS for a plugin hybrid electric vehicle (PHEV is proposed based on the driving cycle model and dynamic programming (DP algorithm. A driving cycle model is constructed by collecting and processing the driving data of a certain school bus. The state of charge (SOC profile can be obtained by the DP algorithm for the whole driving cycle. In order to optimize the energy management strategy in the hybrid power system, the optimal motor torque control sequence can be calculated using the DP algorithm for the segments between the traffic intersections. Compared with the traditional charge depleting-charge sustaining (CDCS strategy, the test results on the ADVISOR platform show a significant improvement in fuel consumption using the EMS proposed in this paper.

Driving a Bus in India: A Study of Indore Bus Rapid Transport System

Directory of Open Access Journals (Sweden)

Siddhartha K. RASTOGI

2017-12-01

Full Text Available Indore is a typical tier-2 town in the central province of India, fast becoming a regional commercial hub in an economically booming state. The city has a population of over 2 million with no significant public transport. Among the multiple options available, the city started implementing a dedicated corridor based Bus Rapid Transport System (BRTS. The project was jointly mooted by the central, state, and city authorities. However, the system encountered a range of problems, including conflicts and pulls between multiple implementing agencies, delays in delivery of hardware and constructions, land acquisition and compensation, vested interests, public interest litigations, and court orders. The paper analyses the BRTS, introduced in Indore in the midst of 2013, from multiple party perspectives with an underlying search for public policy and public management insights. The broad results indicate feasibility and desirability of the project; however, real problems emerge in public and public perception management.

Work fatigue in urban bus drivers

Directory of Open Access Journals (Sweden)

Teresa Makowiec-Dąbrowska

2015-10-01

Full Text Available Background: Bus drivers are a special group of professional drivers who are at a very high risk of fatigue. The aim of the study was to examine whether the driver’s subjective assessment of fatigue allows for the determination of its level and identification of its causes. Material and Methods: The study group comprised 45 randomly selected bus drivers (mean age – 43.7±7.9 years, period of employment as drivers – 14.7±8.6 years. Examinations were performed in all subjects four times – before and after work on the “easy” route (outside the city center, small traffic intensity and before and after work on the “difficult” route (city center, heavy traffic. The fatigue test questionnaire, based on the list of symptoms of fatigue prepared by the Japan Research Committee of Fatigue, was used in the study. Results: The rating of fatigue after the work was significantly higher than that before the work. The profile of fatigue after work was not influenced by the type of route, but the assessment of most symptoms of fatigue reached a higher level after the “difficult” routes and the differences were statistically significant for 7 symptoms. Only the ratings of leg fatigue, feeling of heaviness, and the necessity to squint eyes and gaze with effort reached the higher levels after driving the “easy” routes. It has been found that the level of fatigue was significantly correlated with the job characteristics (driving time, the length of the route, number of stops, etc. and with the abundance of food ingested and type of beverage (coffee vs. others drunk prior to driving. Conclusions: The questionnaire used in our study to assess the subjective feeling of fatigue has proved to be a sensitive and useful tool for indicating the level and causes of fatigue. The relationship between the symptoms of fatigue and the characteristics of job and lifestyle shows that actions must be taken by both the employers and employees to prevent fatigue

Comparing the self-assessed and examiner-assessed driving skills of Japanese driving school students

Directory of Open Access Journals (Sweden)

Hiroshi Nakai

2012-03-01

A sample of Japanese driving test candidates (n=2021 completed a self-assessment using a 5-point scale applied to 19 items. The candidates completed the assessment shortly after passing their practical driving test conducted at a driving school. Their performance was also assessed by an examiner who used the same scale. The comparison between self-assessment and examiner-assessment revealed that around 40% of Japanese driving school students made a realistic assessment of their skills. With regard to the gender differences, although males displayed higher levels of overconfidence than females did, the differences were not as large as earlier studies with questionnaires had suggested. Furthermore, the effect of age on the accuracy of novice drivers' skill assessment was found to be relatively small. Our findings, which are based on a comparison of subjective assessments of driving skills between examiners and novices, instead of a questionable method which relies on a comparison with a hypothetical average driver, suggest that the majority of candidates in fact do not overrate their own skills. These results were discussed from the viewpoint of the driver education system and compared to other European research using the same framework.

Research on Demand for Bus Transport and Transport Habits of High School Students in Žilina Region

Directory of Open Access Journals (Sweden)

Konečný Vladimír

2017-11-01

Full Text Available The paper deals with the analysis of demand for bus transport to examine determinants of demand and practices of high school students based on survey of their transport habits in Žilina Region. Transport habits of students are individual and variable in time. This group of passengers is dependent on public passenger transport services because of their travelling to schools. Significant part of demand for public passenger transport is also formed by this this group of passengers. The knowledge of student's transport habits may help in process of adaptation of offering and quality of transport serviceability what may subsequently stabilize demand for public passenger transport.

Urinary 1-hydroxypyrene and mutagenicity in bus drivers and mail carriers exposed to urban air pollution in Denmark

DEFF Research Database (Denmark)

Hansen, Åse Marie; Wallin, Håkan; Binderup, Mona Lise

2004-01-01

BACKGROUND: Previous studies in Denmark have shown that bus drivers and tramway employees were at an increased risk for developing several types of cancer and that bus drives from central Copenhagen have high levels of biomarkers of DNA damage.AIMS: The present study evaluates 1-hydroxypyrene....../mol creatinine [CI: 0.37-1.47] and female bus drivers 1.90 revertants/mol creatinine [CI: 1.01-2.79] higher mutagenic activity in urine than mail carriers. CONCLUSION: The present study indicates that bus drivers are more exposed to polycyclic aromatic hydrocarbons (PAH) and mutagens than mail carriers. Mail...

Lung and bladder cancer among Danish urban bus drivers and tramway employees: a nested case-control study.

Science.gov (United States)

Soll-Johanning, Helle; Bach, Elsa; Jensen, Steen S

2003-02-01

The combustion of fossil fuels produces small amounts of mutagenic and carcinogenic compounds. We investigated the association between employment and lung and bladder cancer in Danish bus drivers and tramway employees. We carried out a nested case-control study of 153 lung and 84 bladder cancer cases, and 606 controls sampled in a cohort of 18 174 bus drivers or tramway employees employed in Copenhagen during the period 1900-1994. The cases and controls or their next of kin were interviewed about smoking, along with occupational and residential history. An exposure index based on which bus routes the bus drivers had mainly been driving was established. Relative risks (RRs) were estimated by conditional logistic regression. The analysis showed decreasing risk for lung cancer with increasing years of employment as a bus driver (RR = 0.97 for each added year, 95% confidence interval = 0.96-0.99). The air pollution index based on main bus for the bus drivers showed no positive correlation with risk.

Dynamic Bus Travel Time Prediction Models on Road with Multiple Bus Routes.

Science.gov (United States)

Bai, Cong; Peng, Zhong-Ren; Lu, Qing-Chang; Sun, Jian

2015-01-01

Accurate and real-time travel time information for buses can help passengers better plan their trips and minimize waiting times. A dynamic travel time prediction model for buses addressing the cases on road with multiple bus routes is proposed in this paper, based on support vector machines (SVMs) and Kalman filtering-based algorithm. In the proposed model, the well-trained SVM model predicts the baseline bus travel times from the historical bus trip data; the Kalman filtering-based dynamic algorithm can adjust bus travel times with the latest bus operation information and the estimated baseline travel times. The performance of the proposed dynamic model is validated with the real-world data on road with multiple bus routes in Shenzhen, China. The results show that the proposed dynamic model is feasible and applicable for bus travel time prediction and has the best prediction performance among all the five models proposed in the study in terms of prediction accuracy on road with multiple bus routes.

Dynamic Bus Travel Time Prediction Models on Road with Multiple Bus Routes

Science.gov (United States)

Bai, Cong; Peng, Zhong-Ren; Lu, Qing-Chang; Sun, Jian

2015-01-01

Accurate and real-time travel time information for buses can help passengers better plan their trips and minimize waiting times. A dynamic travel time prediction model for buses addressing the cases on road with multiple bus routes is proposed in this paper, based on support vector machines (SVMs) and Kalman filtering-based algorithm. In the proposed model, the well-trained SVM model predicts the baseline bus travel times from the historical bus trip data; the Kalman filtering-based dynamic algorithm can adjust bus travel times with the latest bus operation information and the estimated baseline travel times. The performance of the proposed dynamic model is validated with the real-world data on road with multiple bus routes in Shenzhen, China. The results show that the proposed dynamic model is feasible and applicable for bus travel time prediction and has the best prediction performance among all the five models proposed in the study in terms of prediction accuracy on road with multiple bus routes. PMID:26294903

Cost-effectiveness of active transport for primary school children - Walking School Bus program

Directory of Open Access Journals (Sweden)

Swinburn Boyd

2009-09-01

Full Text Available Abstract Background To assess from a societal perspective the incremental cost-effectiveness of the Walking School Bus (WSB program for Australian primary school children as an obesity prevention measure. The intervention was modelled as part of the ACE-Obesity study, which evaluated, using consistent methods, thirteen interventions targeting unhealthy weight gain in Australian children and adolescents. Methods A logic pathway was used to model the effects on body mass index [BMI] and disability-adjusted life years [DALYs] of the Victorian WSB program if applied throughout Australia. Cost offsets and DALY benefits were modelled until the eligible cohort reached 100 years of age or death. The reference year was 2001. Second stage filter criteria ('equity', 'strength of evidence', 'acceptability', feasibility', sustainability' and 'side-effects' were assessed to incorporate additional factors that impact on resource allocation decisions. Results The modelled intervention reached 7,840 children aged 5 to 7 years and cost $AUD22.8M ($16.6M; $30.9M. This resulted in an incremental saving of 30 DALYs (7:104 and a net cost per DALY saved of $AUD0.76M ($0.23M; $3.32M. The evidence base was judged as 'weak' as there are no data available documenting the increase in the number of children walking due to the intervention. The high costs of the current approach may limit sustainability. Conclusion Under current modelling assumptions, the WSB program is not an effective or cost-effective measure to reduce childhood obesity. The attribution of some costs to non-obesity objectives (reduced traffic congestion and air pollution etc. is justified to emphasise the other possible benefits. The program's cost-effectiveness would be improved by more comprehensive implementation within current infrastructure arrangements. The importance of active transport to school suggests that improvements in WSB or its variants need to be developed and fully evaluated.

Cost-effectiveness of active transport for primary school children - Walking School Bus program.

Science.gov (United States)

Moodie, Marjory; Haby, Michelle; Galvin, Leah; Swinburn, Boyd; Carter, Robert

2009-09-14

To assess from a societal perspective the incremental cost-effectiveness of the Walking School Bus (WSB) program for Australian primary school children as an obesity prevention measure. The intervention was modelled as part of the ACE-Obesity study, which evaluated, using consistent methods, thirteen interventions targeting unhealthy weight gain in Australian children and adolescents. A logic pathway was used to model the effects on body mass index [BMI] and disability-adjusted life years [DALYs] of the Victorian WSB program if applied throughout Australia. Cost offsets and DALY benefits were modelled until the eligible cohort reached 100 years of age or death. The reference year was 2001. Second stage filter criteria ('equity', 'strength of evidence', 'acceptability', feasibility', sustainability' and 'side-effects') were assessed to incorporate additional factors that impact on resource allocation decisions. The modelled intervention reached 7,840 children aged 5 to 7 years and cost $AUD22.8M ($16.6M; $30.9M). This resulted in an incremental saving of 30 DALYs (7:104) and a net cost per DALY saved of $AUD0.76M ($0.23M; $3.32M). The evidence base was judged as 'weak' as there are no data available documenting the increase in the number of children walking due to the intervention. The high costs of the current approach may limit sustainability. Under current modelling assumptions, the WSB program is not an effective or cost-effective measure to reduce childhood obesity. The attribution of some costs to non-obesity objectives (reduced traffic congestion and air pollution etc.) is justified to emphasise the other possible benefits. The program's cost-effectiveness would be improved by more comprehensive implementation within current infrastructure arrangements. The importance of active transport to school suggests that improvements in WSB or its variants need to be developed and fully evaluated.

Bus use and older people: a literature review applying the Person-Environment-Occupation model in macro practice.

Science.gov (United States)

Broome, Kieran; McKenna, Kryss; Fleming, Jennifer; Worrall, Linda

2009-03-01

The same reasons that prompt older people to give up driving can also result in difficulties with accessing public transport. Difficulties using public transport can limit older people's participation in society, thereby impacting negatively on their health. Focusing on public buses, this review explicates the link between bus usability and the health of older people and frames existing evidence on bus usability issues. The Person-Environment-Occupation (PEO) model offers a framework by which bus usability can be assessed. A combination of person-centred, environmental, and occupation-related factors, including bus design, service provision and performance, information, and the attitudes of staff and the community, impact on older people's ability to catch buses. More systematic research needs to take place in order to develop a comprehensive understanding of bus usability. Occupational therapy has a key role to play in conceptualizing, implementing, and evaluating improvements in bus usability for older people.

Stress and strain of short haul bus drivers: psychophysiology as a design oriented method for analysis.

Science.gov (United States)

Göbel, M; Springer, J; Scherff, J

1998-05-01

Psychophysiological measures offer objective information for workplace design according to user requirements. They are, however, rarely applied in industrial practice due to weak points from the designer's point of view, such as the differentiation of various superimposed stressors, inter-individual differences, and the effort required for data acquisition and handling. In this study a set of psychophysiological methods was used to analyse bus driver workplaces as a basis for redesign, and afterwards to evaluate design improvements. During inner-city operation bus drivers are exposed to a particular workload situation, especially due to the high density of traffic and bus stops. Their job is characterized by highly frequent and often simultaneous task execution, performed with a compulsory body posture and under exposure to vibration and noise. To reduce the workload related to the equipment and tasks of bus driving, a research project was initiated to design a new driver workplace that meets the specific ergonomic requirements of the drivers. A detailed workload analysis, consisting of a task analysis, a strain analysis derived from ECG measures and an eye movement analysis was performed during public bus driving in different cities and with different drivers and bus types. Although the results have to be considered as somewhat limited owing to the methodological restraints and conditions of a field study, they provided valuable guidance for design. A new concept for the driver cabin was created based on this database. After installation, this design was evaluated by similar psychophysiological measures. Comparison of the pre- and post results indicates that the redesigned work station reduced workload levels.

Integrated Inverter For Driving Multiple Electric Machines

Science.gov (United States)

Su, Gui-Jia [Knoxville, TN; Hsu, John S [Oak Ridge, TN

2006-04-04

An electric machine drive (50) has a plurality of inverters (50a, 50b) for controlling respective electric machines (57, 62), which may include a three-phase main traction machine (57) and two-phase accessory machines (62) in a hybrid or electric vehicle. The drive (50) has a common control section (53, 54) for controlling the plurality of inverters (50a, 50b) with only one microelectronic processor (54) for controlling the plurality of inverters (50a, 50b), only one gate driver circuit (53) for controlling conduction of semiconductor switches (S1-S10) in the plurality of inverters (50a, 50b), and also includes a common dc bus (70), a common dc bus filtering capacitor (C1) and a common dc bus voltage sensor (67). The electric machines (57, 62) may be synchronous machines, induction machines, or PM machines and may be operated in a motoring mode or a generating mode.

Development and Evaluation of an Economic-Driving Assistance Program for Transit Vehicles

OpenAIRE

Baoxin Han; Wanjing Ma; Hanzhou Xie

2012-01-01

This paper focuses on development and evaluation of an economic-driving assistance program for transit vehicles (EDTV) which can minimize energy consumption, air pollution emission of buses, and improve the level of service of transit system as well. Taking advantage of the latest advances in information and communication technologies, the EDTV system can provide bus drivers with optimal recommended bus holding times at near-side bus stops and dynamic bus speed to adapt to the real-time traff...

Evaluating Nitrogen Oxides and Ultrafine Particulate Matter Emission Features of Urban Bus Based on Real-World Driving Conditions in the Yangtze River Delta Area, China

Directory of Open Access Journals (Sweden)

Dengguo Liu

2018-06-01

Full Text Available A Portable Emission Measurement System was used in this study to evaluate the exhaust emission characteristics of nitrogen oxides (NOx, ultrafine particulate matter (PM, and ultrafine particulate number (PN from buses in the Yangtze River Delta, China. Results showed that NOx emission factor (unit: g·km−1 increased from 5.0 to 19.1, and PM emission factor (unit: g·km−1 increased from 0.001 to 0.189. A nonlinear model was established based on scientific statistical method, which showed that NOx and PM emission factors significantly decreased with speed increasing. The model also showed a “long tail effect” of NOx and PM emission factors beyond 30 km·h−1. Furthermore, hybrid bus exhausted less NOx, PM, and PN emissions compared to conventional bus in the acceleration condition. Exhaust rates of NOx, PM and PN emissions (unit: g·s−1 increased with speed increasing under steady state driving condition, while PN emissions commonly showed a unimodal distribution at the speed of 20 km·h−1.

Bus Route Design with a Bayesian Network Analysis of Bus Service Revenues

Directory of Open Access Journals (Sweden)

Yi Liu

2018-01-01

Full Text Available A Bayesian network is used to estimate revenues of bus services in consideration of the effect of bus travel demands, passenger transport distances, and so on. In this research, the area X in Beijing has been selected as the study area because of its relatively high bus travel demand and, on the contrary, unsatisfactory bus services. It is suggested that the proposed Bayesian network approach is able to rationally predict the probabilities of different revenues of various route services, from the perspectives of both satisfying passenger demand and decreasing bus operation cost. This way, the existing bus routes in the studied area can be optimized for their most probable high revenues.

Driving-behavior-aware stochastic model predictive control for plug-in hybrid electric buses

International Nuclear Information System (INIS)

Li, Liang; You, Sixiong; Yang, Chao; Yan, Bingjie; Song, Jian; Chen, Zheng

2016-01-01

Highlights: • The novel approximated global optimal energy management strategy has been proposed for hybrid powertrains. • Eight typical driving behaviors have been classified with K-means to deal with the multiplicative traffic conditions. • The stochastic driver models of different driving behaviors were established based on the Markov chains. • ECMS was used to modify the SMPC-based energy management strategy to improve its fuel economy. • The approximated global optimal energy management strategy for plug-in hybrid electric buses has been verified and analyzed. - Abstract: Driving cycles of a city bus is statistically characterized by some repetitive features, which makes the predictive energy management strategy very desirable to obtain approximate optimal fuel economy of a plug-in hybrid electric bus. But dealing with the complicated traffic conditions and finding an approximated global optimal strategy which is applicable to the plug-in hybrid electric bus still remains a challenging technique. To solve this problem, a novel driving-behavior-aware modified stochastic model predictive control method is proposed for the plug-in hybrid electric bus. Firstly, the K-means is employed to classify driving behaviors, and the driver models based on Markov chains is obtained under different kinds of driving behaviors. While the obtained driver behaviors are regarded as stochastic disturbance inputs, the local minimum fuel consumption might be obtained with a traditional stochastic model predictive control at each step, taking tracking the reference battery state of charge trajectory into consideration in the finite predictive horizons. However, this technique is still accompanied by some working points with reduced/worsened fuel economy. Thus, the stochastic model predictive control is modified with the equivalent consumption minimization strategy to eliminate these undesirable working points. The results in real-world city bus routines show that the

DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT

Energy Technology Data Exchange (ETDEWEB)

Elana M. Chapman; Shirish Bhide; Jennifer Stefanik; Howard Glunt; Andre L. Boehman; Allen Homan; David Klinikowski

2003-04-01

the bus, operation on the campus shuttle route began in early June 2002. However, the work and challenges continued as it has been difficult to maintain operability of the shuttle bus due to fuel and component difficulties. In late June 2002, the pump head itself developed operational problems (loss of smooth function) leading to excessive stress on the magnetic coupling and excessive current draw to operate. A new pump head was installed on the system to alleviate this problem and the shuttle bus operated successfully on DME blends from 10-25 vol% on the shuttle bus loop until September 30, 2002. During the period of operation on the campus loop, the bus was pulled from service, operated at the PTI test track and real-time emissions measurements were obtained using an on-board emissions analyzer from Clean Air Technologies International, Inc. Particulate emissions reductions of 60% and 80% were observed at DME blend ratios of 12 vol.% and 25 vol.%, respectively, as the bus was operated over the Orange County driving cycle. Increases in NOx, CO and HC emissions were observed, however. In summary, the conversion of the shuttle bus was successfully accomplished, particulate emissions reductions were observed, but there were operational challenges in the field. Nonetheless, they were able to demonstrate reliable operation of the shuttle bus on DME-diesel blends.

A community-based participatory research partnership to reduce vehicle idling near public schools.

Science.gov (United States)

Eghbalnia, Cynthia; Sharkey, Ken; Garland-Porter, Denisha; Alam, Mohammad; Crumpton, Marilyn; Jones, Camille; Ryan, Patrick H

2013-05-01

The authors implemented and assessed the effectiveness of a public health initiative aimed at reducing traffic-related air pollution exposure of the school community at four Cincinnati public schools. A partnership was fostered with academic environmental health researchers and community members. Anti-idling campaign materials were developed and education and training were provided to school bus drivers, students, parents, and school staff. Pledge drives and pre- and posteducation assessments were documented to measure the effectiveness of the program. After completing the educational component of the public health initiative, bus drivers (n = 397), community members (n = 53), and staff (n = 214) demonstrated significantly increased knowledge about the health effects of idling (p public health intervention. A community-driven public health initiative can be effective in both 1) enhancing community awareness about the benefits of reducing idling vehicles and 2) increasing active participation in idling reduction. The partnership initially developed has continued to develop toward a sustainable and growing process.

Bus drivers' exposure to bullying at work: an occupation-specific approach.

Science.gov (United States)

Glasø, Lars; Bele, Edvard; Nielsen, Morten Birkeland; Einarsen, Ståle

2011-10-01

The present study employs an occupation-specific approach to examine bus drivers' exposure to bullying and their trait anger, job engagement, job satisfaction and turnover intentions. A total of 1,023 bus drivers from a large public transport organization participated in the study. The findings show that bus driving can be a high risk occupation with regard to bullying, since 70% of the bus drivers had experienced one or more acts typical of bullying during the last six months. As many as 11% defined themselves as victims of bullying, 33% of whom (i.e. 3.6% of the total sample) see themselves as victims of frequent bullying. Colleagues were most frequently reported as perpetrators. Exposure to bullying was negatively related to job engagement and job satisfaction and positively related to turnover intentions. Job engagement and job satisfaction mediated the relationship between bullying and intention to leave, respectively. Trait anger had an interaction effect on the relationship between bullying and turnover intentions. This study indicates that workplace bullying has context-specific aspects that require increased use of context-specific policies and intervention methods. © 2011 The Authors. Scandinavian Journal of Psychology © 2011 The Scandinavian Psychological Associations.

Drunk driving among novice drivers, possible prevention with additional psychological module in driving school curriculum.

Science.gov (United States)

Eensoo, Diva; Paaver, Marika; Harro, Jaanus

2011-01-01

Road traffic collisions caused by drunk driving pose a significant public health problem all over the world. Therefore additional preventive activities against drunk driving should be worked out. The aim of the study was to assess drunk driving in novice drivers after a psychological intervention taking into account also impulsivity, law obedience, and alcohol-related measures. An intervention study was started with 1889 car driver's license attempters during their driving school studies. Subjects were classified as intervention group (n=1083, mean age 23.1 (SD=7.4) years), control group (n=517, mean age 22.8 (SD=7.1) years) and "lost" group (n=289, mean age 23.0 (SD=6.9) years). "Lost" group subjects had been assigned into the intervention group, but they did not participate in the intervention. Subjects of the intervention group participated in a psychological intervention on the dangers of impulsive behavior in traffic. After a three year follow-up period it appeared that in the control group and in the lost group there was a significantly higher proportion of drunk drivers than in the intervention group, 3.3% (n=17), 3.5% (n=10) and 1.5% (n=10) (p=0.026), respectively. Survival analysis confirmed that psychological intervention had a significant impact on drunk driving (p=0.015), and the impact of the intervention was persistent also in the case of higher scores in Mild social deviance. In subjects with higher scores in impulsivity measures and alcohol-related problems the impact of short psychological intervention was not sufficient for preventing drunk driving. It can be concluded that psychological intervention used during the driving school studies is an effective primary prevention activity against drunk driving. However, for drivers with high scores in impulsivity measures and alcohol-related problems, the short psychological intervention is not sufficient in reducing drunk driving behavior.

Design and Control of a Buck–Boost Charger-Discharger for DC-Bus Regulation in Microgrids

Directory of Open Access Journals (Sweden)

Carlos Andrés Ramos-Paja

2017-11-01

Full Text Available In DC and hybrid microgrids (MG, the DC-bus regulation using Energy Storage Devices (ESD is important for the stable operation of both the generators and loads. There are multiple commercial voltage levels for both ESD and DC-bus; therefore, the ESD voltage may be higher, equal or lower than the DC-bus voltage depending on the application. Moreover, most of the ESD converter controllers are linear-based, hence they ensure stability in a limited operation range. This paper proposes a system to regulate the DC-bus voltage of an MG accounting for any voltage relation between the ESD and the DC-bus voltage. The proposed system is formed by an ESD connected to a DC-bus through a bidirectional Buck–Boost converter, which is regulated by a Sliding-Mode Controller (SMC to ensure the system stability in the entire operation range. The SMC drives the Buck–Boost charger–discharger to regulate the DC-bus voltage, at the desired reference value, by charging or discharging the ESD. This paper also provides detailed procedures to design the parameters of both the SMC and the charger–dischager. Finally, simulation and experimental results validate the proposed solution and illustrate its performance.

Trip-oriented stochastic optimal energy management strategy for plug-in hybrid electric bus

International Nuclear Information System (INIS)

Du, Yongchang; Zhao, Yue; Wang, Qinpu; Zhang, Yuanbo; Xia, Huaicheng

2016-01-01

A trip-oriented stochastic optimal energy management strategy for plug-in hybrid electric bus is presented in this paper, which includes the offline stochastic dynamic programming part and the online implementation part performed by equivalent consumption minimization strategy. In the offline part, historical driving cycles of the fixed route are divided into segments according to the position of bus stops, and then a segment-based stochastic driving condition model based on Markov chain is built. With the segment-based stochastic model obtained, the control set for real-time implemented equivalent consumption minimization strategy can be achieved by solving the offline stochastic dynamic programming problem. Results of stochastic dynamic programming are converted into a 3-dimensional lookup table of parameters for online implemented equivalent consumption minimization strategy. The proposed strategy is verified by both simulation and hardware-in-loop test of real-world driving cycle on an urban bus route. Simulation results show that the proposed method outperforms both the well-tuned equivalent consumption minimization strategy and the rule-based strategy in terms of fuel economy, and even proved to be close to the optimal result obtained by dynamic programming. Furthermore, the practical application potential of the proposed control method was proved by hardware-in-loop test. - Highlights: • A stochastic problem was formed based on a stochastic segment-based driving condition model. • Offline stochastic dynamic programming was employed to solve the stochastic problem. • The instant power split decision was made by the online equivalent consumption minimization strategy. • Good performance in fuel economy of the proposed method was verified by simulation results. • Practical application potential of the proposed method was verified by the hardware-in-loop test results.

Driving the Phileas, a new automated public transport vehicle

NARCIS (Netherlands)

de Waard, Dick; Brookhuis, Karel; Fabriek, Eva; Van Wolffelaar, Peter C.

2004-01-01

Phileas is a high quality public transport vehicle combining characteristics of bus, tram, and the underground. Phileas is equipped with pneumatic tyres and complies with the statutory regulations for buses. Accordingly Phileas may drive everywhere on public roads where buses are allowed to drive.

Methodology of mixed load customized bus lines and adjustment based on time windows

Science.gov (United States)

Song, Rui

2018-01-01

Custom bus routes need to be optimized to meet the needs of a customized bus for personalized trips of different passengers. This paper introduced a customized bus routing problem in which trips for each depot are given, and each bus stop has a fixed time window within which trips should be completed. Treating a trip as a virtual stop was the first consideration in solving the school bus routing problem (SBRP). Then, the mixed load custom bus routing model was established with a time window that satisfies its requirement and the result were solved by Cplex software. Finally, a simple network diagram with three depots, four pickup stops, and five delivery stops was structured to verify the correctness of the model, and based on the actual example, the result is that all the buses ran 124.42 kilometers, the sum of kilometers was 10.35 kilometers less than before. The paths and departure times of the different busses that were provided by the model were evaluated to meet the needs of the given conditions, thus providing valuable information for actual work. PMID:29320505

Bus Route Design with a Bayesian Network Analysis of Bus Service Revenues

OpenAIRE

Liu, Yi; Jia, Yuanhua; Feng, Xuesong; Wu, Jiang

2018-01-01

A Bayesian network is used to estimate revenues of bus services in consideration of the effect of bus travel demands, passenger transport distances, and so on. In this research, the area X in Beijing has been selected as the study area because of its relatively high bus travel demand and, on the contrary, unsatisfactory bus services. It is suggested that the proposed Bayesian network approach is able to rationally predict the probabilities of different revenues of various route services, from...

Individual and population intake fractions of diesel particulate matter (DPM) in bus stop microenvironments

International Nuclear Information System (INIS)

Xu, Jia; Jin, Taosheng; Miao, Yaning; Han, Bin; Gao, Jiajia; Bai, Zhipeng; Xu, Xiaohong

2015-01-01

Diesel particulate matter (DPM) is associated with adverse human health effects. This study aims to investigate the relationship between DPM exposure and emissions by estimating the individual intake fraction (iF_i) and population intake fraction (iF_p) of DPM. Daily average concentrations of particulate matter at two bus stops during rush hours were measured, and then they were apportioned to DPM due to heavy-duty diesel bus emissions using Chemical Mass Balance Model. The DPM emissions of diesel buses for different driving conditions (idling, creeping and traveling) were estimated on the basis of field observations and published emission factors. The median iF_i of DPM was 0.67 and 1.39 per million for commuters standing at the bus stop and pedestrians/cyclists passing through the bus stop during rush hours, respectively. The median iF_p of DPM was 94 per million. Estimations of iF_i and iF_p of DPM are potentially significant for exposure assessment and risk management. - Highlights: • Methods to estimate the individual and population intake fraction in bus stop microenvironments were established. • Source apportionment was performed to estimate the DPM due to diesel bus emissions in bus stop microenvironments. • The DPM emission in bus stop microenvironments rather than in the entire urban area was considered. • The movement of people and their exposure duration were introduced in the estimation of population intake fraction. - This work established a method to estimate the individual and population intake fraction in transportation microenvironments on the basis of PM source apportionment.

Environmental air pollution and DNA adducts in Copenhagen bus drivers - effect of GSTM1 and NAT2 genotypes on adduct level

DEFF Research Database (Denmark)

Nielsen, Per Sabro; de Pater, Nettie; Okkels, Henrik

1996-01-01

The lymphocyte bulky PAH-DNA adduct levels have been studied in persons occupationally exposed to ambient air pollution. The exposure group consisted of 90 healthy, nonsmoking bus drivers from the Copenhagen area, divided into three exposure groups according to driving area, and 60 rural controls...... (smokers and non-smokers). PAH-DNA adducts were determined by 32P-postlabelling with the butanol enrichment procedure. The bus drivers answered a comprehensive questionnaire on passive smoking, residential area, diet and other potential confounding variables. A significantly higher adduct level...... was observed in bus drivers working in central Copenhagen (1.214 fmol/microg DNA, n = 49) compared with both those driving in the dormitory (median: 0.507 fmol/microg DNA, P = 0.046, n = 16) and suburban (median: 0.585 fmol/microg DNA, P = 0.041, n = 25) areas. All three groups had higher adduct levels than...

GO Bus impact analysis.

Science.gov (United States)

2013-08-01

NJ TRANSIT launched two relatively new enhanced bus services: GO 25 serving the : Springfield Avenue corridor in 2008 and GO 28 serving the Bloomfield Avenue corridor in 2009. : As an enhanced but not full Bus Rapid Transit (BRT) service, GO Bus feat...

The Fuel Economy of Hybrid Buses: The Role of Ancillaries in Real Urban Driving

Directory of Open Access Journals (Sweden)

Francesco Bottiglione

2014-07-01

Full Text Available In the present context of the global economic crisis and environmental emergency, transport science is asked to find innovative solutions to turn traditional vehicles into fuel-saving and eco-friendly devices. In the last few years, hybrid vehicles have been shown to have potential benefits in this sense. In this paper, the fuel economy of series hybrid-electric and hybrid-mechanical buses is simulated in two real driving situations: cold and hot weather driving in the city of Taranto, in Southern Italy. The numerical analysis is carried out by an inverse dynamic approach, where the bus speed is given as a velocity pattern measured in the field tests performed on one of the city bus routes. The city of Taranto drive schedule is simulated in a typical tempered climate condition and with a hot temperature, when the air conditioning system must be switched on for passenger comfort. The fuel consumptions of hybrid-electric and hybrid-mechanical buses are compared to each other and with a traditional bus powered by a diesel engine. It is shown that the series hybrid-electric vehicle outperforms both the traditional and the mechanical hybrid vehicles in the cold weather driving simulation, reducing the fuel consumption by about 35% with respect to the traditional diesel bus. However, it is also shown that the performance of the hybrid-electric bus gets dramatically worse when the air-cooling system is continuously turned on. In this situation, the fuel consumption of the three different technologies for city buses under investigation is comparable.

Electrical motor/generator drive apparatus and method

Science.gov (United States)

Su, Gui Jia

2013-02-12

The present disclosure includes electrical motor/generator drive systems and methods that significantly reduce inverter direct-current (DC) bus ripple currents and thus the volume and cost of a capacitor. The drive methodology is based on a segmented drive system that does not add switches or passive components but involves reconfiguring inverter switches and motor stator winding connections in a way that allows the formation of multiple, independent drive units and the use of simple alternated switching and optimized Pulse Width Modulation (PWM) schemes to eliminate or significantly reduce the capacitor ripple current.

Physics Bus: An Innovative Model for Public Engagement

Science.gov (United States)

Fox, Claire

The Physics Bus is about doing science for fun. It is an innovative model for science outreach whose mission is to awaken joy and excitement in physics for all ages and walks of life - especially those underserved by science enrichment. It is a mobile exhibition of upcycled appliances-reimagined by kids-that showcase captivating physics phenomena. Inside our spaceship-themed school bus, visitors will find: a microwave ionized-gas disco-party, fog rings that shoot from a wheelbarrow tire, a tv whose electron beam is controlled by a toy keyboard, and over 20 other themed exhibits. The Physics Bus serves a wide range of public in diverse locations from local neighborhoods, urban parks and rural schools, to cross-country destinations. Its approachable, friendly and relaxed environment allows for self-paced and self-directed interactions, providing a positive and engaging experience with science. We believe that this environment enriches lives and inspires people. In this presentation we will talk about the nuts and bolts that make this model work, how the project got started, and the resources that keep it going. We will talk about the advantages of being a grassroots and community-based organization, and how programs like this can best interface with universities. We will explain the benefits of focusing on direct interactions and why our model avoids ``teaching'' physics content with words. Situating our approach within a body of research on the value of informal science we will discuss our success in capturing and engaging our audience. By the end of this presentation we hope to broaden your perception of what makes a successful outreach program and encourage you to value and support alternative outreach models such as this one. In Collaboration with: Eva Luna, Cornell University; Erik Herman, Cornell University; Christopher Bell, Ithaca City School District.

Optimization of a PEMFC/battery pack power system for a bus application

International Nuclear Information System (INIS)

Barelli, Linda; Bidini, Gianni; Ottaviano, Andrea

2012-01-01

Highlights: ► A dynamic model of a PEMFC/battery system for bus traction has been developed. ► The model incorporates the dynamics of the fuel cell and the state of charge (SOC) of the battery pack. ► The system output power have been determined according to the real driving load demand of a bus during 12 h. ► The model has allowed the sizing of the fuel cell and the hydrogen tank with the SOC control strategy optimization. ► The PEMFC power that allows to optimize the operation in terms of both SOC control strategy and consumption is 33 kW e . -- Abstract: In a global environment context in which the urgent need to reduce pollutant emissions is of central relevance, it is becoming increasingly important the research for solutions, concerning the vehicular transport sector with low environmental impact. Fuel cell technology is expected to become a viable solution for these applications due to its environmental friendly characteristics. The present study concerns the traction system of a bus considering the case of hybrid solutions consisting of a proton exchange membrane fuel cell (PEMFC) in parallel with a battery pack. In particular, a dynamic model of a PEMFC/battery system is presented for the application under study. The model incorporates the dynamics of the fuel cell and the state of charge (SOC) of the battery pack. The fuel cell and the battery output power have been determined according to the real driving load demand of a bus taking into consideration a daily operation of 12 h. Such a model has allowed the correct dimensioning of the hybrid power system (giving a particular attention to the fuel cell and the hydrogen tank) together with the optimization of the SOC control strategy.

Evolutionary algorithm for vehicle driving cycle generation.

Science.gov (United States)

Perhinschi, Mario G; Marlowe, Christopher; Tamayo, Sergio; Tu, Jun; Wayne, W Scott

2011-09-01

Modeling transit bus emissions and fuel economy requires a large amount of experimental data over wide ranges of operational conditions. Chassis dynamometer tests are typically performed using representative driving cycles defined based on vehicle instantaneous speed as sequences of "microtrips", which are intervals between consecutive vehicle stops. Overall significant parameters of the driving cycle, such as average speed, stops per mile, kinetic intensity, and others, are used as independent variables in the modeling process. Performing tests at all the necessary combinations of parameters is expensive and time consuming. In this paper, a methodology is proposed for building driving cycles at prescribed independent variable values using experimental data through the concatenation of "microtrips" isolated from a limited number of standard chassis dynamometer test cycles. The selection of the adequate "microtrips" is achieved through a customized evolutionary algorithm. The genetic representation uses microtrip definitions as genes. Specific mutation, crossover, and karyotype alteration operators have been defined. The Roulette-Wheel selection technique with elitist strategy drives the optimization process, which consists of minimizing the errors to desired overall cycle parameters. This utility is part of the Integrated Bus Information System developed at West Virginia University.

Individual and population intake fractions of diesel particulate matter (DPM) in bus stop microenvironments.

Science.gov (United States)

Xu, Jia; Jin, Taosheng; Miao, Yaning; Han, Bin; Gao, Jiajia; Bai, Zhipeng; Xu, Xiaohong

2015-12-01

Diesel particulate matter (DPM) is associated with adverse human health effects. This study aims to investigate the relationship between DPM exposure and emissions by estimating the individual intake fraction (iFi) and population intake fraction (iFp) of DPM. Daily average concentrations of particulate matter at two bus stops during rush hours were measured, and then they were apportioned to DPM due to heavy-duty diesel bus emissions using Chemical Mass Balance Model. The DPM emissions of diesel buses for different driving conditions (idling, creeping and traveling) were estimated on the basis of field observations and published emission factors. The median iFi of DPM was 0.67 and 1.39 per million for commuters standing at the bus stop and pedestrians/cyclists passing through the bus stop during rush hours, respectively. The median iFp of DPM was 94 per million. Estimations of iFi and iFp of DPM are potentially significant for exposure assessment and risk management. Copyright © 2015 Elsevier Ltd. All rights reserved.

Beyond a man's world: contributions from considering gender in the study of bus drivers' work activity.

Science.gov (United States)

Cunha, Liliana; Nogueira, Sónia; Lacomblez, Marianne

2014-01-01

Bus driving is a typically male occupation undergoing a process of feminization. Although men remain a majority, women's integration has raised some questions, namely, related to work organization or its impact on health. This paper focuses on the contributions of assuming a gender perspective in the analysis of the bus driving occupation and the conditions under which it is performed. Twenty female and 158 male bus drivers. Qualitative and quantitative approaches were combined. Ergonomic work analysis and individual interviews were used, as well as INSAT (Work and Health Questionnaire). Difficulties inherent to the work activity were highlighted, in terms of working hours and management of "peripheral tasks", with implications for the balance between professional and personal life. These difficulties were reported differently by men and women, although both made themselves clear about the impact on their career and health. Taking gender into consideration has enabled an enrichment of the questions that guide the analysis of this work activity, and contributed to a new perspective on the work performed by this occupational group as well as a new approach to study the history of the transport industry by proposing as focus of analysis issues related to "gender mobility".

Designing Sustainable Public Transportation: Integrated Optimization of Bus Speed and Holding Time in a Connected Vehicle Environment

Directory of Open Access Journals (Sweden)

Wei Wu

2016-11-01

Full Text Available Developing public transportation and giving priority to buses is a feasible solution for improving the level of public transportation service, which facilitates congestion alleviation and prevention, and contributes to urban development and city sustainability. This paper presents a novel bus operation control strategy including both holding control and speed control to improve the level of service of transit systems within a connected vehicle environment. Most previous work focuses on optimization of signal timing to decrease the bus signal delay by assuming that holding control is not applied; the speed of buses is given as a constant input and the acceleration and deceleration processes of buses can be neglected. This paper explores the benefits of a bus operation control strategy to minimize the total cost, which includes bus signal delay, bus holding delay, bus travel delay, acceleration cost due to frequent stops and intense driving. A set of formulations are developed to explicitly capture the interaction between bus holding control and speed control. Experimental analysisand simulation tests have shown that the proposed integrated operational model outperforms the traditional control, speed control only, or holding control only strategies in terms of reducing the total cost of buses. The sensitivity analysis has further demonstrated the potential effectiveness of the proposed approach to be applied in a real-time bus operation control system under different levels of traffic demand, bus stop locations, and speed limits.

Fuel cell propulsion for urban duty vehicles: Bavarian fuel cell bus project

International Nuclear Information System (INIS)

Wurster, R.; Altmann, M.; Sillat, D.; Kalk, K. W.; Hammerschmidt, A.; Stuehler, W.; Holl, E.

1998-01-01

Following a feasibility study and a detailed specification phase, the realization of a fuel cell city bus prototype was started in autumn 1996. The project is a joint development effort of Siemens, MAN and Linde, which receives a 50 % funding by the Bavarian State Ministry for Economic Affairs, Transport and Technology (BStMWVT) in the context of the Hydrogen Initiative Bavaria. An MAN low-floor bus will be equipped with the components for a fuel cell drive system. The PEM fuel cell is developed by the power generation division of Siemens. Four fuel cell modules deliver a total electrical output of 120 kW to the two electric motors, which are linked by a summation gearbox by the Siemens Transportation Systems Division. MAN Technologie AG is responsible for the compressed hydrogen storage system allowing for a driving range of more than 250 km, while Linde AG takes care of the hydrogen periphery and delivers the hydrogen for the test operation scheduled for the beginning of the year 2000. Project coordination is done by Ludwig-Boelkow System-technik GmbH. The project is divided into four phases. The conceptual design phase is scheduled to last until the end of 1997. The partly overlapping system integration phase will end in the first quarter of 1999. The subsequent test and commissioning phase will prepare the test operation at the beginning of 2000 with a bus operator yet to be defined. (author)

Hybrid Electric Transit Bus

Science.gov (United States)

Viterna, Larry A.

1997-01-01

A government, industry, and university cooperative is developing an advanced hybrid electric city transit bus. Goals of this effort include doubling the fuel economy compared to current buses and reducing emissions to one-tenth of current EPA standards. Unique aspects of the vehicle's power system include the use of ultra-capacitors as an energy storage system, and a planned natural gas fueled turbogenerator developed from a small jet engine. Power from both the generator and energy storage system is provided to a variable speed electric motor attached to the rear axle. At over 15000 kg gross weight, this is the largest vehicle of its kind ever built using ultra-capacitor energy storage. This paper describes the overall power system architecture, the evolution of the control strategy, and its performance over industry standard drive cycles.

Optimal bus temperature for thermal comfort during a cool day.

Science.gov (United States)

Velt, K B; Daanen, H A M

2017-07-01

A challenge for electric buses is to minimize heating and cooling power to maximally extend the driving range, but still provide sufficient thermal comfort for the driver and passengers. Therefore, we investigated the thermal sensation (TS) and thermal comfort (TC) of passengers in buses during a cool day (temperature 13.4 ± 0.5 °C, relative humidity (RH) 60 ± 5.8%) typical for the Dutch temperate maritime climate. 28 Males and 72 females rated TS and TC and gave information on age, stature, body weight and worn garments. The temperature in the bus of 22.5 ± 1.1 °C and RH of 59.9 ± 5.8% corresponded to a slightly warm feeling (TS = 0.85 ± 1.06) and TC of 0.39 ± 0.65. TS related significantly to bus temperature, clothing insulation and age. Linear regression based on these parameters showed that the temperature in the bus corresponding to TC = 0 and TS = 0 would have been 20.9 ± 0.6 °C. In conclusion, a 1.6 °C lower bus temperature during the investigated cool day probably would have led to less thermal discomfort and energy savings of electrical busses. The methodology to relate climatic measurements to subjective assessments is currently employed in a wider climatic range and may prove to be useful to find a better balance between thermal comfort and energy savings of the bus. Copyright © 2017 Elsevier Ltd. All rights reserved.

LHC on the bus

CERN Multimedia

Laëtitia Pedroso

2010-01-01

On 15 December, an airport bus will be transformed in the image of CERN. The bus will be seen by the thousands of travellers arriving in Geneva, informing them of the possibility to visit CERN.   Sketch of the bus. The good relationship between Geneva International Airport and CERN started several years ago. In 2004 the airport put advertising space in the arrivals area at CERN's disposal free of charge. Now, starting on 15 December, a 40-foot long bus will display a giant sticker advertisement depicting CERN as it takes passengers over the airport tarmac to their planes. This is no ordinary sticker, and it was no mean task to attach it to the bus. The task of producing and attaching it was entrusted to Geneva-based specialists Mathys SA. With the ski season opening on 15 December, there will be many travellers arriving at the airport, and the bus will be ready to receive them. When one thinks of CERN, the subjects that naturally come to mind are the LHC, the mysteries of the Universe...

Measurements of ultrafine particles and other vehicular pollutants inside school buses in South Texas

Science.gov (United States)

Zhang, Qunfang; Zhu, Yifang

2010-01-01

Increasing evidence has demonstrated toxic effects of vehicular emitted ultrafine particles (UFPs, diameter pollutants, especially UFPs, was measured inside four diesel-powered school buses. Two 1990 and two 2006 model year diesel-powered school buses were selected to represent the age extremes of school buses in service. Each bus was driven on two routine bus runs to study school children's exposure under different transportation conditions in South Texas. The number concentration and size distribution of UFPs, total particle number concentration, PM 2.5, PM 10, black carbon (BC), CO, and CO 2 levels were monitored inside the buses. The average total particle number concentrations observed inside the school buses ranged from 7.3 × 10 3 to 3.4 × 10 4 particles cm -3, depending on engine age and window position. When the windows were closed, the in-cabin air pollutants were more likely due to the school buses' self-pollution. The 1990 model year school buses demonstrated much higher air pollutant concentrations than the 2006 model year ones. When the windows were open, the majority of in-cabin air pollutants came from the outside roadway environment with similar pollutant levels observed regardless of engine ages. The highest average UFP concentration was observed at a bus transfer station where approximately 27 idling school buses were queued to load or unload students. Starting-up and idling generated higher air pollutant levels than the driving state. Higher in-cabin air pollutant concentrations were observed when more students were on board.

On the road to fossil-free public transport: The case of Swedish bus fleets

International Nuclear Information System (INIS)

Xylia, Maria; Silveira, Semida

2017-01-01

Public transport is important for Sweden to acquire a fossil-fuel independent vehicle fleet by 2030. The aim of this paper is to assess the status of Swedish public bus fleets towards decarbonization, and explore factors affecting regional performance variations and fuel choices. Environmental performance indicators such as renewable fuel shares, CO 2 emissions, and energy efficiency are analyzed nationally and regionally. Fuel preferences and best practices are investigated through a survey and interviews with experts working with strategic planning at Public Transport Authorities. Almost 60% of the bus transport volume ran on renewables in 2014 compared to 8% in 2007, but regional variations are significant, partly due to factors such as driving conditions, bus and fuel types, typical trip lengths, and climatic conditions. However, there is no strong correlation between population densities or bus transport volume and the share of renewables achieved. This places political will, strategic planning and policies to promote public transport as key factors affecting renewable fuel deployment. Environmental factors are a priority when choosing fuels, while barriers to renewable fuels are mainly economic and political. Meanwhile, despite the overall progress, achievements in energy efficiency improvement are falling short in comparison to emissions reduction and adoption of renewable fuels, thus requiring further attention. - Highlights: • The penetration of renewables in Swedish public bus fleets reached ca. 60% in 2014. • Public bus emissions per vehicle-km have decreased by 43% between 2007 and 2014. • Efforts are needed to improve energy efficiency in bus transport. • Electricity is likely to receive increased attention according to expert survey.

HEV Test Bench Based on CAN Bus Sensor Communication

Directory of Open Access Journals (Sweden)

Shupeng ZHAO

2014-02-01

Full Text Available The HEV test bench based on Controller Area Network bus was studied and developed. Control system of HEV power test bench used the CAN bus technology. The application of CAN bus technology on control system development has opened up a new research direction for domestic automobile experimental platform. The HEV power control system development work was completed, including power master controller, electric throttle controller, driving simulation platform, CAN2.0 B communication protocol procedures for formulation, CAN communication monitoring system, the simulation model based on MATLAB code automatic generation technology research, etc. Maximum absorption power of the test bench is 90 kW, the test bench top speed is 6000 r/min, the CAN communication data baud rate is 10~500 k, the conventional electric measurement parameter part precision satisfies the requirement of development of HEV. On the HEV test bench the result of regenerative braking experiment shows that the result got by the test bench was closer to the results got by outdoor road test. And the fuel consumption experiment test results show that the HEV fuel consumption and the charge-discharge character are in linear relationship. The establishment of the test platform for the evaluation of the development of hybrid electric vehicle and power provides physical simulation and test platform.

Fuel cell bus operation, system investigation H2 bus

International Nuclear Information System (INIS)

Anon.

1992-01-01

The WP covers two tasks: - Prepartion of Technical Catalogue: In cooperation with ICIL, AR have compiled a technical catalogue, providing the impartial descriptions, both of existing technology and regulations, and the likely future developments of these, as to remedy the first problem faced by a potential hydrogen bus fleet operator viz the absence of an impartial description of the available vehicle and fuels systems together with the absence of a description of regulatory and safety factors which need consideration. - Fuel Cell Bus Operation - System Investigation H 2 Bus: The application of fuel cell electric generation systems to hybrid electrical buses or electrical busses without any storage system on board is considered. The task will cover safety and environmental aspects, a cost estimate and a market evaluation. (orig.)

For Safety and Sanity's Sake, Help Bus Drivers Keep Peace on the Ride to School.

Science.gov (United States)

Trotter, Andrew

1987-01-01

Outlines common-sense tips for disciplining student bus riders that are recommended by several driver-training programs. Themes include the following: (1) Set a few clear rules for proper bus behavior; (2) be positive; and (3) establish amiable communication with the children and with the principal as well. (CJH)

School transportation mode, by distance between home and school, United States, ConsumerStyles 2012.

Science.gov (United States)

Beck, Laurie F; Nguyen, Daniel D

2017-09-01

Motor-vehicle crashes are a leading cause of death among children in the United States, and almost one-fourth of all trips by school-aged children are trips to and from school. This study sought to determine how children (5-18years) travel to and from school and, among those living ≤1mile of school, to explore the role of school bus service eligibility on school travel mode. We used national 2012 survey data to determine prevalence of usual school travel mode, stratified by distance from school. For those living ≤1mile of school, multivariable regression was conducted to assess the association between bus service eligibility and walking or bicycling. Almost half (46.6%) of all children rode in passenger vehicles (PV) to school and 41.8% did so for the trip home. Results were similar among those living ≤1mile (48.1%, PV to school; 41.3%, PV to home). Among those living ≤1mile, 21.9% and 28.4% of children walked or bicycled to and from school, respectively. Ineligibility for school bus service was strongly associated with walking or bicycling to school [adjusted prevalence ratio (aPR: 5.36; ppassenger vehicles were a common mode of travel. For children who live close to school, the role that school bus service eligibility plays in walking or bicycling deserves further consideration. Given the large proportion of children who use passenger vehicles for school travel, effective interventions can be adopted to increase proper child restraint and seat belt use and reduce crash risks among teen drivers. Better understanding of conditions under which bus service is offered to children who live close to school could inform efforts to improve pedestrian and bicyclist safety for school travel. Published by Elsevier Ltd.

Development and Evaluation of an Economic-Driving Assistance Program for Transit Vehicles

Directory of Open Access Journals (Sweden)

Baoxin Han

2012-02-01

Full Text Available This paper focuses on development and evaluation of an economic-driving assistance program for transit vehicles (EDTV which can minimize energy consumption, air pollution emission of buses, and improve the level of service of transit system as well. Taking advantage of the latest advances in information and communication technologies, the EDTV system can provide bus drivers with optimal recommended bus holding times at near-side bus stops and dynamic bus speed to adapt to the real-time traffic control plan at downstream intersections. In order to address the impacts of the stochastic variation of bus dwell time, the total link between adjacent intersections is divided into three parts: upstream of bus stop part; bus stop part; and downstream of bus stop part. The methods for calculating recommended parameters, including bus holding time and bus speed in each of the three parts are proposed based on real-time bus status and signal status at downstream intersections. A VISSIM-based simulation platform was designed and used for simulating and evaluating the proposed EDTV system. Extensive experimental analyses have shown that the proposed EDTV system can improve the performance of a transit system in terms of reducing fuel consumption, air pollution emissions and level of service of the transit system.

Taking Physics and Now the Stars on the Road With the Magic Physics Bus

Science.gov (United States)

Bennum, David

2009-05-01

In February 2003 the ``Physics on the Road'' workshop, held at Colorado State University- Fort Collins, Colorado, brought together physics faculty who were experienced in designing and providing year --round mobile physics displays and those who were interested in initiating similar outreach programs. The impetus for the workshop was the upcoming ``World Year of Physics'', but the workshop had much broader impact for many of us who attended. The University of Nevada had a long history of demonstration shows for campus visitors from K-12 students/faculty but the cost of field trips began to limit this for many schools, especially for schools in poorer neighborhoods without large scale parental fundraising. The timing of the workshop was perfect for my developing program to utilize a donated ``electric bus'' as a traveling physics demo showcase. The program has grown to near our current limitations (70 mile range of the bus and time considerations), however we are expanding the ``scope'' of the project to include evening astronomy ``star parties'' as we enter the ``Year of Astronomy''. In addition to the bus transport of portable astronomy equipment to school sites we are adding, through donation, a 22 inch telescope in a domed observatory at a secondary campus location at the edge of Reno where large scale ``star parties'' can be conducted as outreach to K-12 and the community. The ``Physics on the Road'' bus reaches several thousand elementary and middle school students every year now and the potential for similar outreach with ``Stars on the Road'' has excited several of our faculty and physics students into increased participation in these endeavors to introduce our young people to science. It has become one of our most active ``recruitment'' plans and growing numbers of local students entering physics and other science majors is anecdotal evidence of success.

Here's What Our Schools Are Doing to Combat Drunk Driving.

Science.gov (United States)

Gersten, Leon

1984-01-01

A 2-year-old drunk-driving program developed in the Deer Park, New York, public schools has included a week-long campaign addressing Deer Park high school students and an "awareness week" meeting for parents. Both events made extensive use of experts and audiovisual aids. Information for obtaining the latter is provided. (JBM)

Bus systems in motor vehicles; Bussysteme im Kfz

Energy Technology Data Exchange (ETDEWEB)

Schule, Roland

2008-07-01

There is hardly any modern vehicle without a bus system. This interactive learning software explains why electric and electronic systems in motor vehicles should be linked and uses various bus types to illustrate the various alternatives, bus structures, and data types. The physical side of bus systems is gone into, the data structure is explained, and the various bus typologies are outlined. From the fundamentals of bus systems, the software proceeds to present the most important bus systems and their main properties. Subjects: Diagnosis bus, LIN bus, CAN bus, MOST bus, Bluetooth. The bus systems EIA-485, LVDS, D{sup 2}B, byteflight, and Flexray are briefly characterised. (orig.)

[Reliability and validity of Driving Anger Scale in professional drivers in China].

Science.gov (United States)

Li, Z; Yang, Y M; Zhang, C; Li, Y; Hu, J; Gao, L W; Zhou, Y X; Zhang, X J

2017-11-10

Objective: To assess the reliability and validity of the Chinese version of Driving Anger Scale (DAS) in professional drivers in China and provide a scientific basis for the application of the scale in drivers in China. Methods: Professional drivers, including taxi drivers, bus drivers, truck drivers and school bus drivers, were selected to complete the questionnaire. Cronbach's α and split-half reliability were calculated to evaluate the reliability of DAS, and content, contract, discriminant and convergent validity were performed to measure the validity of the scale. Results: The overall Cronbach's α of DAS was 0.934 and the split-half reliability was 0.874. The correlation coefficient of each subscale with the total scale was 0.639-0.922. The simplified version of DAS supported a presupposed six-factor structure, explaining 56.371% of the total variance revealed by exploratory factor analysis. The DAS had good convergent and discriminant validity, with the success rate of calibration experiment of 100%. Conclusion: DAS has a good reliability and validity in professional drivers in China, and the use of DAS is worth promoting in divers.

Scaling Laws in Chennai Bus Network

OpenAIRE

Chatterjee, Atanu; Ramadurai, Gitakrishnan

2015-01-01

In this paper, we study the structural properties of the complex bus network of Chennai. We formulate this extensive network structure by identifying each bus stop as a node, and a bus which stops at any two adjacent bus stops as an edge connecting the nodes. Rigorous statistical analysis of this data shows that the Chennai bus network displays small-world properties and a scale-free degree distribution with the power-law exponent, $\\gamma > 3$.

Cansancio y somnolencia en conductores de ómnibus y accidentes de carretera en el Perú: estudio cuantitativo Tiredness and sleepiness in bus drivers and road accidents in Peru: a quantitative study

Directory of Open Access Journals (Sweden)

Jorge Rey de Castro

2004-07-01

Full Text Available OBJETIVO: Evaluar la relación del cansancio y la somnolencia en los conductores de ómnibus con los accidentes de carretera. La información obtenida de diversos países atribuye a la somnolencia del conductor una parte importante en la génesis de los accidentes de carretera. No obstante, la información al respecto es escasa en el caso del Perú. MÉTODOS: Se realizó un estudio transversal, de índole observacional y comparativa, basado en una encuesta prevalidada y de aplicación supervisada, entre 238 conductores de ómnibus que circulan por la carretera Panamericana Norte del Perú. Para determinar la relación entre variables se emplearon la prueba de ji al cuadrado y el índice de Pearson, con un valor de significación de P OBJECTIVE: To evaluate the relationship that tiredness and sleepiness in bus drivers have to road accidents in Peru. Information from various countries indicates that driver sleepiness plays an important role in road accidents. However, there is only limited information on this subject in Peru. METHODS: Using a supervised, pretested survey, a cross-sectional observational and comparative study was carried out with 238 bus drivers who drive on the Northern Pan American Highway of Peru. To determine the relationship between variables the chi-square test was used, along with the Pearson correlation coefficient. The level of significance was set at P < 0.05. The variables analyzed were: tiredness, sleepiness, hours of driving per day, daily hours of sleep, body mass index, snoring, sleep apnea, and either having had or almost having had an accident while driving. RESULTS: Of the 238 drivers, all of them were men, 45% said they had had or nearly had had an accident while driving, 55% slept less than 6 hours per day, 31% had slept less than 6 hours in the 24 hours before answering the survey, and 80% were in the habit of driving more than 5 hours without stopping. Of the drivers, 56% of them reported being tired at least

Mental workload and its relation with fatigue among urban bus drivers

Directory of Open Access Journals (Sweden)

Narmin Hassanzadeh-Rangi

2017-06-01

Full Text Available Introduction: Driving crash is one of major concerns in all countries. Mental workload reflects the level of attention resources required to meet both objec­tive and subjective performance criteria, which may be affected by task demand, external support, and past experience. Mental workload has been commonly cited as a major cause of workplace and transportation accidents. The objective of this study was assessment of mental workload and its relation with fatigue among urban bus drivers in Tehran, Iran. Methods: In this descriptive and analytical study, the NASA-TLX workload scale and the Samn-Perelli fatigue scale were completed by 194 professional bus drivers. Descriptive statistics as well as correlation and regression analysis were performed for data processing. Results: The total mental workload had highest correlation with the physical demand(r=0.73, p<0.001, the mental demand (r=0.68, p<0.001 and the time pressure (r=0.58, p<0.001. The total fatigue perceived by bus driver had highest correlation with the frustration level (r=0.42, p<0.001, the time pressure (r=0.24, p<0.001 and the mental workload (r=0.21, p<0.001. Conclusion: Mental workload, physical workload and time pressure are important determinants of the total mental workload and fatigue perceived by urban bus drivers. A comprehensive intervention program, include work turnover, trip and work-rest scheduling as well as smoking cessation, was recommended to improve mental workload and fatigue. 

TPG bus passes

CERN Multimedia

Staff Association

2013-01-01

The CERN Staff Association will stop selling TPG bus passes. All active and retired members of the CERN personnel will be able to purchase Unireso bus passes from the CERN Hostel - Building 39 (Meyrin site) from 1st February 2013. For more information: https://cds.cern.ch/journal/CERNBulletin/2013/04/Announcements/1505279?ln=en

School bus’s level of service in Malang City

Science.gov (United States)

Hariyani, S.

2017-06-01

School Bus began operated on the 12th of January 2015. Provision of school buses is expected to reduce not only the use of vehicles by students, but it is also to reduce the number of traffic jams. Malang school bus facilities provided by the Department of Transport in cooperation with the Department of Education to serve students in elementary school, junior and senior high schools. After the service running two years, based on the preliminary observation not all students are interested in using the school bus. The research objective was to measure the school bus’s level service. The method to measure school bus’s level of service was used Importance Performance analysis (IPA). The results showed that through IPA, it can be concluded that school bus’s level of service in Malang City have been able to serve students/customers with the mean of degree suitability (Tki) is 111. Meanwhile it must be observed and get more attention to improve by government, attributes which is lies in the first quadrant or concentrate here (attribute Adequate space, Seating capacity, Availability trash can, Passenger facility down in points, The availability of information boards in each bus stop, Availability public telephone in each bus stop, and Availability CCTV in each bus), in order to increase its performance.

Air-pollution and economics: diesel bus versus electric bus

OpenAIRE

Adheesh, SR; Vasisht, Shravanth M; Ramasesha, Sheela K

2016-01-01

The Bangalore Metropolitan Transport Corporation (BMTC) took an initiative to check the overall benefits of introducing electric buses as a suitable replacement for the diesel buses to tackle the burgeoning pollution in the city of Bengaluru, India. For a trial run of three months, an electric bus was procured from a Chinese company `Build Your Dreams' (BYD). Data were collected by BMTC on the operation and maintenance of the bus. This new initiative, if rightly guided, could have a direct im...

In-use fuel economy of hybrid-electric school buses in Iowa.

Science.gov (United States)

Hallmark, Shauna; Sperry, Bob; Mudgal, Abhisek

2011-05-01

Although it is much safer and more fuel-efficient to transport children to school in buses than in private vehicles, school buses in the United States still consume 822 million gal of diesel fuel annually, and school transportation costs can account for a significant portion of resource-constrained school district budgets. Additionally, children in diesel-powered school buses may be exposed to higher levels of particulates and other pollutants than children in cars. One solution to emission and fuel concerns is use of hybrid-electric school buses, which have the potential to reduce emissions and overall lifecycle costs compared with conventional diesel buses. Hybrid-electric technologies are available in the passenger vehicle market as well as the transit bus market and have a track record indicating fuel economy and emissions benefits. This paper summarizes the results of an in-use fuel economy evaluation for two plug-in hybrid school buses deployed in two different school districts in Iowa. Each school district selected a control bus with a route similar to that of the hybrid bus. Odometer readings, fuel consumption, and maintenance needs were recorded for each bus. The buses were deployed in 2008 and data were collected through May 2010. Fuel consumption was calculated for each school district. In Nevada, IA, the overall average fuel economy was 8.23 mpg for the hybrid and 6.35 mpg for the control bus. In Sigourney, IA, the overall average fuel economy was 8.94 mpg for the hybrid and 6.42 mpg for the control bus. The fuel consumption data were compared for the hybrid and control buses using a Wilcoxon signed rank test. Results indicate that fuel economy for the Nevada hybrid bus was 29.6% better than for the Nevada control bus, and fuel economy for the Sigourney hybrid bus was 39.2% higher than for the Sigourney control bus. Both differences were statistically significant.

Request-Centric Wireless Bus Information Management System

Directory of Open Access Journals (Sweden)

Ying-Chih Chen

2016-11-01

Full Text Available This invention relates to a wireless bus information management system, which includes bus stop and vehicle management subsystems. The management signals are transmittable between bus stops and the vehicle. Based on vehicle management signals, the bus stop management subsystem can obtain information about the bus route identification, the number of unoccupied seats, the intention to stop or not, etc. Similarly, with the bus stop management signals, the vehicle management subsystem can make the decision of stopping. Accordingly, when a passenger wants to get off the vehicle or there are unoccupied seats, the vehicle management subsystem will inform the bus stop management subsystem such that the passengers waiting at the bus stop may flexibly schedule their travel plan. The proposed distributed wireless system is detailed by a prototype implementation and a simulation analysis, which is shown to be feasible and scalable.

Analysis of robustness of urban bus network

Science.gov (United States)

Tao, Ren; Yi-Fan, Wang; Miao-Miao, Liu; Yan-Jie, Xu

2016-02-01

In this paper, the invulnerability and cascade failures are discussed for the urban bus network. Firstly, three static models(bus stop network, bus transfer network, and bus line network) are used to analyse the structure and invulnerability of urban bus network in order to understand the features of bus network comprehensively. Secondly, a new way is proposed to study the invulnerability of urban bus network by modelling two layered networks, i.e., the bus stop-line network and the bus line-transfer network and then the interactions between different models are analysed. Finally, by modelling a new layered network which can reflect the dynamic passenger flows, the cascade failures are discussed. Then a new load redistribution method is proposed to study the robustness of dynamic traffic. In this paper, the bus network of Shenyang City which is one of the biggest cities in China, is taken as a simulation example. In addition, some suggestions are given to improve the urban bus network and provide emergency strategies when traffic congestion occurs according to the numerical simulation results. Project supported by the National Natural Science Foundation of China (Grant Nos. 61473073, 61374178, 61104074, and 61203329), the Fundamental Research Funds for the Central Universities (Grant Nos. N130417006, L1517004), and the Program for Liaoning Excellent Talents in University (Grant No. LJQ2014028).

Growing with Driving Leadership Style in School: A Case Study on Leadership of Finnish Elementary Schools in Tampere

Science.gov (United States)

Rajbhandari, Mani Man Singh

2012-01-01

"Driving leadership style" of the school leadership proclaims to be important in bringing about changes in behavioural aspect of the followers. The hallmark of driving leadership style illustrated the characteristic of teaming, toning, tasking, timing and transforming with realistic view to subjective approach. This allowed the…

National fuel cell bus program : proterra fuel cell hybrid bus report, Columbia demonstration.

Science.gov (United States)

2011-10-01

This report summarizes the experience and early results from a fuel cell bus demonstration funded by the Federal Transit Administration (FTA) under the National Fuel Cell Bus Program. A team led by the Center for Transportation and the Environment an...

78 FR 64274 - Qualification of Drivers; Exemption Applications; Vision

Science.gov (United States)

2013-10-28

... license from the state of Missouri with passenger and school bus endorsements. He has driven a school bus for 7 years without incident. He has not had an accident in 36 years of civilian driving. Despite his... miles without any accidents.'' Mr. Thiboutot reported that he has driven straight trucks for 15 years...

Bus fuel consumption model

Energy Technology Data Exchange (ETDEWEB)

Zargari, S.A. [Iran Univ. of Science and Technology, Teheran (Iran, Islamic Republic of); Khan, A.M. [Carleton Univ., Ottawa, ON (Canada). Dept. of Civil and Environmental Engineering

2000-07-01

The interest in rapid bus transit has increased sharply with the realization that modern metropolitan areas rely on public transit to provide for strong economies and communities. As a prevention tool against traffic congestion, deteriorating air quality and rising greenhouse gas emissions, this study of bus fuel consumption was designed to assist in the planning and management of rapid bus transit. The Australian Road Research Board's (ARRB) Road Fuel Consumption Model was used as a starting point. The estimations required were realized with the help of Newtonian Mechanics. The four states of vehicular traffic were examined: acceleration, cruise, deceleration, and idle. The estimated total power required from the engine to overcome resistance forces, to run vehicle accessories and overcome internal engine friction was calculated. The data for the standard and articulated bus was obtained from OC Transpo in Ottawa. The study permitted the authors to conclude that the estimations for the parameters for power requirements and fuel consumption for heavy duty vehicles are appropriate. The methodology for the estimation of fuel consumption on the Transitway, which is part of the rapid bus transit system, proved adequate. In addition, the methodology was useful to estimate fuel savings resulting from demand management strategies with potential for modal shift. 9 refs., 6 tabs.

Electrical system architecture having high voltage bus

Science.gov (United States)

Hoff, Brian Douglas [East Peoria, IL; Akasam, Sivaprasad [Peoria, IL

2011-03-22

An electrical system architecture is disclosed. The architecture has a power source configured to generate a first power, and a first bus configured to receive the first power from the power source. The architecture also has a converter configured to receive the first power from the first bus and convert the first power to a second power, wherein a voltage of the second power is greater than a voltage of the first power, and a second bus configured to receive the second power from the converter. The architecture further has a power storage device configured to receive the second power from the second bus and deliver the second power to the second bus, a propulsion motor configured to receive the second power from the second bus, and an accessory motor configured to receive the second power from the second bus.

Electric drive systems including smoothing capacitor cooling devices and systems

Energy Technology Data Exchange (ETDEWEB)

Dede, Ercan Mehmet; Zhou, Feng

2017-02-28

An electric drive system includes a smoothing capacitor including at least one terminal, a bus bar electrically coupled to the at least one terminal, a thermoelectric device including a first side and a second side positioned opposite the first side, where the first side is thermally coupled to at least one of the at least one terminal and the bus bar, and a cooling element thermally coupled to the second side of the thermoelectric device, where the cooling element dissipates heat from the thermoelectric device.

Design & Development of FPGA Based VME Bus Controller

OpenAIRE

Himali Patel; Poornima Talwai

2015-01-01

The VME bus interface Controller (VIC068A) is used to interface Local CPU bus and VME bus. VME Bus Controller is used in wide application areas where high reliability, good accuracy and high speed are desired to withstand industrial environment like nuclear power plant and process industries. VME Bus controller can configure as Master, Slave, Interrupt Handler, arbiter as well as power monitor. Commercial VME Bus interface controller chips are available from a few vend...

Sudden illness while driving a vehicle--a retrospective analysis of commercial drivers in Japan.

Science.gov (United States)

Hitosugi, Masahito; Gomei, Sayaka; Okubo, Takao; Tokudome, Shogo

2012-01-01

We performed a retrospective analysis of commercial drivers to clarify the background of incidents of sudden illness while driving. The analysis used reports submitted by employers to the Japan Ministry of Land, Infrastructure, Transport, and Tourism regarding commercial drivers who had been ordered to stop driving owing to health problems. Of 211 cases with an average work history of 15.2 years, there were 88 bus drivers, 70 taxi drivers, and 53 truck drivers, 36.0% of who had died as a result of their disease. Among taxi and truck drivers, more than 70% of incidents were due to cardiac, aortic, and cerebrovascular disease. More than 80% of these were unable to avoid traffic accidents caused by sudden illness. However, among bus drivers, cardiac, aortic, and cerebrovascular disease accounted for only 23.5% of incidents, and accidents were avoided in more than half of the cases. The duration between starting work and the incident time was significantly shorter among bus drivers [mean 3.3 hours, standard deviation (SD) 3.1] than taxi (7.7 hours, SD 5.8) and truck (7.2 hours, SD 6.3) drivers (Pprevent disabling events while driving. As a precaution, physicians should advise commercial drivers to stop driving as soon as they detect slight discomfort. To prevent accidents, more assertive health promotion aimed at professional drivers is needed.

Economic Optimization Analysis of Chengdu Electric Community Bus Operation

Science.gov (United States)

Yidong, Wang; Yun, Cai; Zhengping, Tan; Xiong, Wan

2018-03-01

In recent years, the government has strongly supported and promoted electric vehicles and has given priority to demonstration and popularization in the field of public transport. The economy of public transport operations has drawn increasing attention. In this paper, Chengdu wireless charging pure electric community bus is used as the research object, the battery, air conditioning, driver’s driving behavior and other economic influence factors were analyzed, and optimizing the operation plan through case data analysis, through the reasonable battery matching and mode of operation to help businesses effectively save operating costs and enhance economic efficiency.

Evaluation of intelligent transport systems impact on school transport safety

Directory of Open Access Journals (Sweden)

Jankowska-Karpa Dagmara

2017-01-01

Full Text Available The integrated system of safe transport of children to school using Intelligent Transport Systems was developed and implemented in four locations across Europe under the Safeway2School (SW2S project, funded by the EU. The SW2S system evaluation included speed measurements and an eye-tracking experiment carried out among drivers who used the school bus route, where selected elements of the system were tested. The subject of the evaluation were the following system elements: pedestrian safety system at the bus stop (Intelligent Bus Stop and tags for children, Driver Support System, applications for parents’ and students’ mobile phones, bus stop inventory tool and data server. A new sign designed for buses and bus stops to inform about child transportation/children waiting at the bus stop was added to the system. Training schemes for system users were also provided. The article presents evaluation results of the impact of selected elements of the SW2S system on school transport safety in Poland.

Learning NServiceBus Sagas

CERN Document Server

Helton, Rich

2015-01-01

If you are an Enterprise C# developer who wishes to extend your knowledge of NServiceBus and Enterprise Service Bus in C#, this is the book for you. This book is designed to enhance the education of ESBs and their messaging, whether you are a beginner or a seasoned expert in Enterprise C#, Apex, and Visualforce pages.

Bus and Tag Terminators for IBM system/360

CERN Multimedia

Control units were connected to the channels with "Bus and Tag" cable pairs. The bus cables carried the address and data information and the tag cables identified what data was on the bus. There were three general types of bus-and-tag cables produced by IBM.

Self-assessed job satisfaction and ischaemic heart disease mortality: a 10-year follow-up of urban bus drivers

DEFF Research Database (Denmark)

Netterstrøm, B; Suadicani, P

1993-01-01

Several studies have shown that bus driving is a high-risk occupation for ischaemic heart disease (IHD). In order to study contributing factors in the job, all male full-time bus drivers in the three major cities in Denmark were followed for 10 years. It was hypothesized that bus drivers who...... working in a high traffic intensity area, RR = 1.6. In contrast to what was expected, men who reported a high degree of job satisfaction had increased risk of IHD. Those who did not look for another job had a highly significant sixfold increased risk of future death from IHD. Also those who reported never...... in the literature on self-assessed job strain and risk of IHD may be partly explained by the fact that studies in general have focused on absence or presence of the psychosocial factor in question. A more differentiated assessment of exposure might prove more useful....

Emission inventory estimation of an intercity bus terminal.

Science.gov (United States)

Qiu, Zhaowen; Li, Xiaoxia; Hao, Yanzhao; Deng, Shunxi; Gao, H Oliver

2016-06-01

Intercity bus terminals are hotspots of air pollution due to concentrated activities of diesel buses. In order to evaluate the bus terminals' impact on air quality, it is necessary to estimate the associated mobile emission inventories. Since the vehicles' operating condition at the bus terminal varies significantly, conventional calculation of the emissions based on average emission factors suffers the loss of accuracy. In this study, we examined a typical intercity bus terminal-the Southern City Bus Station of Xi'an, China-using a multi-scale emission model-(US EPA's MOVES model)-to quantity the vehicle emission inventory. A representative operating cycle for buses within the station is constructed. The emission inventory was then estimated using detailed inputs including vehicle ages, operating speeds, operating schedules, and operating mode distribution, as well as meteorological data (temperature and humidity). Five functional areas (bus yard, platforms, disembarking area, bus travel routes within the station, and bus entrance/exit routes) at the terminal were identified, and the bus operation cycle was established using the micro-trip cycle construction method. Results of our case study showed that switching to compressed natural gas (CNG) from diesel fuel could reduce PM2.5 and CO emissions by 85.64 and 6.21 %, respectively, in the microenvironment of the bus terminal. When CNG is used, tail pipe exhaust PM2.5 emission is significantly reduced, even less than brake wear PM2.5. The estimated bus operating cycles can also offer researchers and policy makers important information for emission evaluation in the planning and design of any typical intercity bus terminals of a similar scale.

Stochastic Bus Dispatching Model untuk Optimalisasi Jumlah Bus Transjakarta Koridor 3

Directory of Open Access Journals (Sweden)

Zahedi Zahedi

2011-12-01

Full Text Available The increasing number of road user causing traffic jam finds out a way, busway. However, in its implementation, the number of fleet available does not enough to take the passengers. It results in the an amassed of passengers at several bus stops. This leads to passenger dissatisfaction satisfaction which eventually causes Transjakarta users to reuse private cars. Definitely this situation may builds up traffic jams. Stochastic Bus Dispatching Model is used to simulate public transportation that operates regularly. 

Road safety issues for bus transport management.

Science.gov (United States)

Cafiso, Salvatore; Di Graziano, Alessandro; Pappalardo, Giuseppina

2013-11-01

Because of the low percentage of crashes involving buses and the assumption that public transport improves road safety by reducing vehicular traffic, public interest in bus safety is not as great as that in the safety of other types of vehicles. It is possible that less attention is paid to the significance of crashes involving buses because the safety level of bus systems is considered to be adequate. The purpose of this study was to evaluate the knowledge and perceptions of bus managers with respect to safety issues and the potential effectiveness of various technologies in achieving higher safety standards. Bus managers were asked to give their opinions on safety issues related to drivers (training, skills, performance evaluation and behaviour), vehicles (maintenance and advanced devices) and roads (road and traffic safety issues) in response to a research survey. Kendall's algorithm was used to evaluate the level of concordance. The results showed that the majority of the proposed items were considered to have great potential for improving bus safety. The data indicated that in the experience of the participants, passenger unloading and pedestrians crossing near bus stops are the most dangerous actions with respect to vulnerable users. The final results of the investigation showed that start inhibition, automatic door opening, and the materials and internal architecture of buses were considered the items most strongly related to bus passenger safety. Brake assistance and vehicle monitoring systems were also considered to be very effective. With the exception of driver assistance systems for passenger and pedestrian safety, the perceptions of the importance of other driver assistance systems for vehicle monitoring and bus safety were not unanimous among the bus company managers who participated in this survey. The study results showed that the introduction of new technologies is perceived as an important factor in improving bus safety, but a better understanding

TMS communications software. Volume 2: Bus interface unit

Science.gov (United States)

Gregor, P. J.

1979-01-01

A data bus communication system to support the space shuttle's Trend Monitoring System (TMS) and to provide a basis for evaluation of the bus concept is described. Installation of the system included developing both hardware and software interfaces between the bus and the specific TMS computers and terminals. The software written for the microprocessor-based bus interface units is described. The software implements both the general bus communications protocol and also the specific interface protocols for the TMS computers and terminals.

Mastering NServiceBus and persistence

CERN Document Server

Helton, Rich

2014-01-01

This book is intended for developers, designers, and architects alike who wish to build C# NServiceBus enterprise architectures and learn how ESB persists data and messages to help them attain their goals. No prior knowledge of persistence in NServiceBus is required.

Bus Rapid Transit and Socioeconomic Condition of Bus Commuters in Lagos State

Directory of Open Access Journals (Sweden)

Owolabi L. Kuye

2017-10-01

Full Text Available Road transport is one of the most common means of transportation across the world. Bus transportation in Nigeria had witnessed many problems for the past decades considering the growing population with the attendant loss of lives and properties in most cities like Lagos in Nigeria. This paper focuses on the adequacy of services provided by Bus Rapid Transit (BRT in Lagos State with respect to the extent to which it influences the socioeconomic conditions of bus commuters. It examines the effect of services rendered by BRT on cost reduction potential, income and safety. Multistage sampling technique was used to select 20 samples each from all respondents in all local government area in Lagos State to reach a total of three hundred and thirty (330 samples. The data collection instrument was the questionnaire which was validated. Data collected were analysed with the use of descriptive statistics such as means, percentages and standard deviation and inferential statistics such as regression and analysis of variance techniques. Findings showed that BRT services has reduced the cost of bus commuters and also increased safety and security thereby increasing the socioeconomic condition of Lagosians. The study recommends improvements in BRT services through the deployment of technology as it had been used in developed countries.

Loss minimization control and efficiency determination of electric drives in traction applications

Energy Technology Data Exchange (ETDEWEB)

Windisch, Thomas; Hofmann, Wilfried [Technische Univ. Dresden (Germany). Lehrstuhl fuer Elektrische Maschinen und Antriebe

2012-11-01

High-power electric drives in automotive traction applications consume a large part of the disposable electric energy. For this reason the energy efficiency of the drives is of great importance for range and fuel consumption of the hybrid electric vehicle. The paper describes two possible drives with different electric motors from a control point of view. The electric power losses in the drive system are determined depending on the operating point of the machine. With these loss characteristics the control of the drives is optimized to produce minimal losses. Finally the energy efficiency for a realistic urban bus drive cycle is calculated to compare the two types. (orig.)

The Development and Verification of a Novel ECMS of Hybrid Electric Bus

Directory of Open Access Journals (Sweden)

Jun Wang

2014-01-01

Full Text Available This paper presents the system modeling, control strategy design, and hardware-in-the-loop test for a series-parallel hybrid electric bus. First, the powertrain mathematical models and the system architecture were proposed. Then an adaptive ECMS is developed for the real-time control of a hybrid electric bus, which is investigated and verified in a hardware-in-the-loop simulation system. The ECMS through driving cycle recognition results in updating the equivalent charge and discharge coefficients and extracting optimized rules for real-time control. This method not only solves the problems of mode transition frequently and improves the fuel economy, but also simplifies the complexity of control strategy design and provides new design ideas for the energy management strategy and gear-shifting rules designed. Finally, the simulation results show that the proposed real-time A-ECMS can coordinate the overall hybrid electric powertrain to optimize fuel economy and sustain the battery SOC level.

Digital processing data communication systems (bus systems). Digitale Prozessdaten-Kommunikations-Systeme (Bus Systeme)

Energy Technology Data Exchange (ETDEWEB)

Fleck, K

1980-01-01

After an introduction to the technology of digital processing data communication systems there are the following chapters: digital communication of processing data in automation technology, the technology of biserial communication, the implementaiton of a bus system, the data transmission of the TDC-2000 system of Honeywell's and the process bus CS 275 in the automation system TELEPERM M of Siemens AG.

Connecting and Networking for Schools

Science.gov (United States)

Resources for connecting and networking for schools through e-newsletters, finding school IAQ Champions and other EPA school programs such as Asthma, Energy Star, Clean School Bus USA, School Flag, etc.

77 FR 12360 - Qualification of Drivers; Exemption Applications; Epilepsy and Seizure Disorders

Science.gov (United States)

2012-02-29

... known medical condition (e.g., drug reaction, high temperature, acute infectious disease, dehydration... exemption, he would return to driving a school bus. His physician has released him to return to driving...

SPFC bus design studies

Energy Technology Data Exchange (ETDEWEB)

Potter, L.; Reinkingh, J.

1999-07-01

This report presents the results of a study assessing the design options for a solid polymer fuel cell bus. Commercial and operation requirements, environmental and market drivers, and fuel processor modeling are examined. Power train specifications and detailed system design are investigated covering fuel cell system dynamic response, hybrid system size, fuel cell system start-up time, system specifications, and hybrid bus component dimensions and costs. (UK)

Comparison of the combustion engine operating parameters and the ecological indicators of an urban bus in dynamic type approval tests and in actual operating conditions

Directory of Open Access Journals (Sweden)

Rymaniak Lukasz

2017-01-01

Full Text Available The article presents the considerations regarding a city bus combustion engine performanceparameters in dynamic type approval tests and in real operating conditions when servicing an urban bus line. A comparison of the designated engine operating time shares with respect to load and crankshaft rotational speed was made. The analysis included the ETC and WHTC tests, which showed significant discrepancies in the work areas of internal combustion engines in these test when compared to actual driving conditions. The details of the type approval tests used and the method of their denormalization for the drive unit were presented. The vehicle used for this research was an eighteen meter city bus equipped with a CI engine with a displacement of 9.2 dm3. The latest PEMS mobile equipment technology was used to conduct the road measurements. This allowed the emission indicators for CO, HC, NOx and PM to be determined, including specific emissions. The obtained values were then compared with the Euro V limits.The analysis of the test results was supplemented with the calculation of fuel consumption using the carbonbalance method.

Pybus - A Python Software Bus

International Nuclear Information System (INIS)

Lavrijsen, Wim T.L.P.

2004-01-01

A software bus, just like its hardware equivalent, allows for the discovery, installation, configuration, loading, unloading, and run-time replacement of software components, as well as channeling of inter-component communication. Python, a popular open-source programming language, encourages a modular design on software written in it, but it offers little or no component functionality. However, the language and its interpreter provide sufficient hooks to implement a thin, integral layer of component support. This functionality can be presented to the developer in the form of a module, making it very easy to use. This paper describes a Pythonmodule, PyBus, with which the concept of a ''software bus'' can be realized in Python. It demonstrates, within the context of the ATLAS software framework Athena, how PyBus can be used for the installation and (run-time) configuration of software, not necessarily Python modules, from a Python application in a way that is transparent to the end-user

Working conditions of bus drivers in the private sector and bus crashes in Kandy district, Sri Lanka: a case-control study.

Science.gov (United States)

Jayatilleke, A U; Nakahara, S; Dharmaratne, S D; Jayatilleke, A C; Poudel, K C; Jimba, M

2009-04-01

To explore the effects of working conditions of private-bus drivers on bus crashes in Kandy district, Sri Lanka. A case-control study was carried out from August to September 2006. All private-bus drivers registered in Kandy district and involved in crashes reported to the police between November 2005 and April 2006 (n = 63) were selected as cases. Two control groups were included: private-bus drivers working on the same routes as the case drivers (n = 90) and private-bus drivers selected randomly from other routes of the district (n = 111). Data were collected using an anonymous self-administered questionnaire. Associations between working conditions and crashes were analysed using logistic regression. A strong association was observed between drivers' disagreements about working hours and bus crashes (matched controls, adjusted odds ratio (AOR) 5.98, 95% CI 1.02 to 34.90; unmatched controls, AOR 18.74, 95% CI 2.00 to 175.84). A significant association was also observed between low salaries (US$100) and private-bus crashes (matched controls, AOR 1.01, 95% CI 0.40 to 2.54; unmatched controls, AOR 3.09, 95% CI 1.26 to 7.57). Drivers' disagreements about working hours and low salaries were significant risk factors for private-bus crashes in Kandy district, Sri Lanka. Therefore, new legislation for private-bus owners on the working hours and salaries of their drivers to prevent private-bus crashes is recommended.

Comparison and status of 32 bit backplane bus architectures

International Nuclear Information System (INIS)

Muller, K.D.

1985-01-01

With the introduction of 32 bit microprocessors several new 32 bit backplane bus architectures have been developed and are in the process for standardization. Among these are Future Bus (IEEE P896.1), VME-Bus (IEEE 1014), MULTIBUS II, Nu-Bus and Fastbus (IEEE 960). The paper describes and compares the main features of these bus architectures and mentions the status of national and international standardization efforts

PCISIM - A Simulation Tool for PCI Bus Based Systems

DEFF Research Database (Denmark)

Sharp, Robin

1999-01-01

This document describes a PCI bus simulator for use in evaluating the feasibility of system designs based on this bus.......This document describes a PCI bus simulator for use in evaluating the feasibility of system designs based on this bus....

The Bus Station Spacing Optimization Based on Game Theory

Directory of Open Access Journals (Sweden)

Changjiang Zheng

2015-01-01

Full Text Available With the development of city, the problem of traffic is becoming more and more serious. Developing public transportation has become the key to solving this problem in all countries. Based on the existing public transit network, how to improve the bus operation efficiency, and reduce the residents transit trip cost has become a simple and effective way to develop the public transportation. Bus stop spacing is an important factor affecting passengers’ travel time. How to set up bus stop spacing has become the key to reducing passengers’ travel time. According to comprehensive traffic survey, theoretical analysis, and summary of urban public transport characteristics, this paper analyzes the impact of bus stop spacing on passenger in-bus time cost and out-bus time cost and establishes in-bus time and out-bus time model. Finally, the paper gets the balance best station spacing by introducing the game theory.

Bus accident severity and passenger injury: evidence from Denmark

DEFF Research Database (Denmark)

Prato, Carlo Giacomo; Kaplan, Sigal

2014-01-01

Purpose Bus safety is a concern not only in developing countries, but also in the U.S. and Europe. In Denmark, disentangling risk factors that are positively or negatively related to bus accident severity and injury occurrence to bus passengers can contribute to promote safety as an essential...... principle of sustainable transit and advance the vision “every accident is one too many”. Methods Bus accident data were retrieved from the national accident database for the period 2002–2011. A generalized ordered logit model allows analyzing bus accident severity and a logistic regression enables...... examining occurrence of injury to bus passengers. Results Bus accident severity is positively related to (i) the involvement of vulnerable road users, (ii) high speed limits, (iii) night hours, (iv) elderly drivers of the third party involved, and (v) bus drivers and other drivers crossing in yellow or red...

Particulates and noise exposure during bicycle, bus and car commuting: A study in three European cities.

Science.gov (United States)

Okokon, Enembe O; Yli-Tuomi, Tarja; Turunen, Anu W; Taimisto, Pekka; Pennanen, Arto; Vouitsis, Ilias; Samaras, Zissis; Voogt, Marita; Keuken, Menno; Lanki, Timo

2017-04-01

In order to curb traffic-related air pollution and its impact on the physical environment, contemporary city commuters are encouraged to shift from private car use to active or public transport modes. However, personal exposures to particulate matter (PM), black carbon and noise during commuting may be substantial. Therefore, studies comparing exposures during recommended modes of transport versus car trips are needed. We measured personal exposure to various-sized particulates, soot, and noise during commuting by bicycle, bus and car in three European cities: Helsinki in Finland, Rotterdam in the Netherlands and Thessaloniki in Greece using portable monitoring devices. We monitored commonly travelled routes in these cities. The total number of one-way trips yielding data on any of the measured parameters were 84, 72, 94 and 69 for bicycle, bus, closed-window car and open-window car modes, respectively. The highest mean PM 2.5 (85µg/m 3 ), PM 10 (131µg/m 3 ), black carbon (10.9µg/m 3 ) and noise (75dBA) levels were recorded on the bus, bus (again), open-window car and bicycle modes, respectively, all in Thessaloniki, PM and soot concentrations were generally higher during biking and taking a bus than during a drive in a a car with closed windows. Ratios of bike:car PM 10 ranged from 1.1 in Thessaloniki to 2.6 in Helsinki, while bus:car ratios ranged from in 1.0 in Rotterdam to 5.6 in Thessaloniki. Higher noise levels were mostly recorded during bicycle rides. Based on our study, active- and public-transport commuters are often at risk of higher air pollution and noise exposure than private car users. This should be taken into account in urban transportation planning. Copyright © 2017 Elsevier Inc. All rights reserved.

Shuttle bus services quality assessment Tangerang Selatan toward smart city

Science.gov (United States)

Fassa, Ferdinand; Sitorus, Fredy Jhon Philip; Adikesuma, Tri Nugraha

2017-11-01

Around the world, shuttle bus operation played the significant role to accommodate transportation for commuting bus passengers. Shuttle Bus services in cities are provided by various bus agencies with kinds of own specific purposes. For instance, at Tangerang Selatan, Indonesia, it was said that shuttle bus In Trans Bintaro is run and operated by private bus companies hire by Bintaro developer. The aim of this research is to identify factors of satisfaction of shuttle bus service in Kota Tangerang Selatan, Indonesia. Several factors are used to analyze sums of 20 parameters performance indicators of Shuttle Bus. A face to face interview using a questionnaire (N=200) was used to collect data on October and March 2017. Likert and diagram Cartesian were used to model the all the parameters. This research succeeded in finding some categories of Shuttle bus service attributes such as accessibility, comfort, and safety. Users agreed that eight indicators in shuttle bus have the excellent achievement, while three indicators on performance remain low and should receive more attention especially punctuality of the bus.

Security awareness for public bus transportation : case studies of attacks against the Israeli public bus system.

Science.gov (United States)

2012-03-01

This report presents 16 case studies of attacks planned or carried out against Israeli bus targets, along with statistical data on the number, frequency, and lethality of attacks against bus targets that have taken place in Israel since 1970 and duri...

Evaluation of Traffic Accident Risk in In-City Bus Drivers: The Use of Berlin Questionnaire

Science.gov (United States)

Ekren, Pervin Korkmaz; Uysal, Funda Elmas; Başoğlu, Özen K.

2018-01-01

OBJECTIVES Traffic accidents associated with high mortality rate may produce serious problems especially in highways. Obstructive sleep apnea (OSA) has been associated with a high risk for traffic accidents due to excessive daytime sleepiness even in in-city drivers. In the present study, it was aimed to evaluate the rate of OSA symptoms and to identify risk factors associated with traffic accidents in in-city bus drivers. MATERIAL AND METHODS A self-administered questionnaire including demographic and anthropometric features, sleep and work schedules, Berlin questionnaire, Epworth sleepiness score (ESS), and history of traffic accidents was used. RESULTS The questionnaire was conducted for 1400 male bus drivers (mean age, 38.0±6.4 y, body mass index, 27.8±3.9 kg/m2). A total of 1058 (75.6%) drivers had one or more accidents while driving bus. According to the Berlin questionnaire, 176 (12.6%) drivers were found to have high OSA risk and the accident rate was 83.0% in high-risk group, whereas 74.5% of low-risk drivers had accidents (p=0.043). The drivers with a history of traffic accident were older (p=0.030), had higher ESS (p=0.019), and were more in the high-risk OSA group according to the Berlin questionnaire (p=0.015). In multivariate linear regression analysis, traffic accident was associated with only Berlin questionnaire (p=0.015). CONCLUSION The present results support that city bus drivers with high OSA risk according to Berlin questionnaire have increased accident rates. Therefore, we suggest using Berlin questionnaire for screening sleep apnea not only in highway drivers but also in in-city bus drivers. PMID:29755810

77 FR 6178 - FY 2012 Discretionary Funding Opportunities: Bus and Bus Facilities Programs (State of Good...

Science.gov (United States)

2012-02-07

... not limited to: Rail, ferry, intercity bus and private transportation providers. In order to be..., intercity bus, and private transportation providers. In order to be eligible for funding, intermodal... automobile travel, improving the pedestrian environment of a community or, use of environmental design...

Global Optimal Energy Management Strategy Research for a Plug-In Series-Parallel Hybrid Electric Bus by Using Dynamic Programming

Directory of Open Access Journals (Sweden)

Hongwen He

2013-01-01

Full Text Available Energy management strategy influences the power performance and fuel economy of plug-in hybrid electric vehicles greatly. To explore the fuel-saving potential of a plug-in hybrid electric bus (PHEB, this paper searched the global optimal energy management strategy using dynamic programming (DP algorithm. Firstly, the simplified backward model of the PHEB was built which is necessary for DP algorithm. Then the torque and speed of engine and the torque of motor were selected as the control variables, and the battery state of charge (SOC was selected as the state variables. The DP solution procedure was listed, and the way was presented to find all possible control variables at every state of each stage in detail. Finally, the appropriate SOC increment is determined after quantizing the state variables, and then the optimal control of long driving distance of a specific driving cycle is replaced with the optimal control of one driving cycle, which reduces the computational time significantly and keeps the precision at the same time. The simulation results show that the fuel economy of the PEHB with the optimal energy management strategy is improved by 53.7% compared with that of the conventional bus, which can be a benchmark for the assessment of other control strategies.

American fuel cell bus project : first analysis report.

Science.gov (United States)

2013-06-01

This report summarizes the experience and early results from the American Fuel Cell Bus Project, a fuel cell electric bus demonstration : funded by the Federal Transit Administration (FTA) under the National Fuel Cell Bus Program. A team led by CALST...

Project survey for trolley-bus transport; Johdinautoliikenteen hankeselvitys

Energy Technology Data Exchange (ETDEWEB)

Anttila, T.; Eklund, P.; Airaksinen, S.; Maettoe, R.; Laehdetie, A.

2011-04-15

To investigate the feasibility and rationality of the revival of trolley bus traffic in Helsinki a full size project plan was conducted for a variety of alternatives. This included a survey on the latest developments of the trolley bus technology, three optional plans for route network, a budgetary level design for a fully functional depot in Koskela bus depot, examination of urban landscape structures, a study on organisational options, particular technical specifications applicable on suitable trolley buses and an examination of the impacts on the environment and on the future development of public transport. The basic concept of a trolley bus as a means of electric public transport vehicle has found its form over the years, but all the components of the system undergo at present intensive development. In context of this survey also the option of a fully autonomous electric bus powered by accumulators or fuel cells and the like was investigated. However, such technology is still totally inadequate for a heavy duty bus. There are no economically competitive and effective systems available as yet. The trolley bu is the far most reliable system and gives the best life cycle economy for a foreseeable future. Earliest estimates for alternative electric technologies in regular bus service are viable just after one investment cycle some time beyond 2030. Then it should be possible to run without the support of a comprehensive overhead line. The latest achievements in the development of trolley bus are auxiliary engine and accumulator systems allowing for more autonomous propulsion. Nowadays, trolley buses are equipped with an auxiliary power unit that alleviates the traditional restrictions of the overhead line. The modern trolley bus may run short distances without the trolley lines. Recuperation of the kinetic energy at deceleration (braking) either into the overhead line network or by storing it in the vehicle is one of the characteristics of modern trolley buses

Urinary 1-hydroxypyrene and mutagenicity in bus drivers and mail carriers exposed to urban air pollution in Denmark.

Science.gov (United States)

Hansen, Ase Marie; Wallin, Håkan; Binderup, Mona Lise; Dybdahl, Marianne; Autrup, Herman; Loft, Steffen; Knudsen, Lisbeth Ehlert

2004-01-10

Previous studies in Denmark have shown that bus drivers and tramway employees were at an increased risk for developing several types of cancer and that bus drives from central Copenhagen have high levels of biomarkers of DNA damage. The present study evaluates 1-hydroxypyrene concentrations and mutagenic activity in urine as biomarkers of exposure in non-smoking bus drivers in city and rural areas on a work day and a day off and in non-smoking mail carriers working outdoors (in the streets) and indoors (in the office). Twenty-four hour urine samples were collected on a working day and a day off from 60 non-smoking bus drivers in city and rural areas and from 88 non-smoking mail carriers working outdoors (in the streets) and indoors (in the office). The concentration of 1-hydroxypyrene was measured by means of HPLC and the mutagenic activity was assessed by the Ames assay with Salmonella tester strain YG1021 and S9 mix. The N-acetyltransferase (NAT2) phenotype was used as a biomarker for susceptibility to mutagenic/carcinogenic compounds. Bus drivers excreted more 1-hydroxypyrene in urine than did mail carriers. The differences were slightly smaller when NAT2 phenotype, cooking at home, exposure to vehicle exhaust, and performing physical exercise after work were included. The NAT2 slow acetylators had 29% (1.29 [CI: 1.15-1.98]) higher 1-hydroxypyrene concentrations in urine than the fast acetylators. Male bus drivers had 0.92 revertants/mol creatinine [CI: 0.37-1.47] and female bus drivers 1.90 revertants/mol creatinine [CI: 1.01-2.79] higher mutagenic activity in urine than mail carriers. The present study indicates that bus drivers are more exposed to polycyclic aromatic hydrocarbons (PAH) and mutagens than mail carriers. Mail carriers who worked outdoors had higher urinary concentration of 1-hydroxypyrene, a marker of exposure to PAH, than those working indoors. The individual levels of urinary mutagenic activity were not correlated to excretion of 1

A Conceptual Approach for Optimising Bus Stop Spacing

Science.gov (United States)

Johar, Amita; Jain, S. S.; Garg, P. k.

2017-06-01

An efficient public transportation system is essential of any country. The growth, development and shape of the urban areas are mainly due to availability of good transportation (Shah et al. in Inst Town Plan India J 5(3):50-59, 1). In developing countries, like India, travel by local bus in a city is very common. The accidents, congestion, pollution and appropriate location of bus stops are the major problems arising in metropolitan cities. Among all the metropolitan cities in India, Delhi has highest percentage of growth of population and vehicles. Therefore, it is important to adopt efficient and effective ways to improve mobility in different metropolitan cities in order to overcome the problem and to reduce the number of private vehicles on the road. The primary objective of this paper is to present a methodology for developing a model for optimum bus stop spacing (OBSS). It describes the evaluation of existing urban bus route, data collection, development of model for optimizing urban bus route and application of model. In this work, the bus passenger generalized cost method is used to optimize the spacing between bus stops. For the development of model, a computer program is required to be written. The applicability of the model has been evaluated by taking the data of urban bus route of Delhi Transport Corporation (DTC) in Excel sheet in first phase. Later on, it is proposed to develop a programming in C++ language. The developed model is expected to be useful to transport planner for rational design of the spacing of bus stops to save travel time and to generalize operating cost. After analysis it is found that spacing between the bus stop comes out to be between 250 and 500 m. The Proposed Spacing of bus stops is done considering the points that they don't come nearer to metro/rail station, entry or exit of flyover and near traffic signal.

Peptic ulcer among urban bus drivers in Denmark

DEFF Research Database (Denmark)

Netterstrøm, Bo; Juel, K

1990-01-01

As part of a survey on the work environment of bus drivers, 2045 (83%) of 2465 male bus drivers in the three major cities in Denmark in 1978 answered a postal questionnaire on health and working conditions. In order to evaluate the relative occurrence of peptic ulcer among the bus drivers, a follow......-up study was also conducted. All hospital discharges with a peptic ulcer diagnosis among the bus drivers were registered from the Danish National Patient Register. All Danish men were used as reference group. On the basis of the 1978-questionnaire association between occupational and psychosocial factors...... and subsequent hospital discharge with a peptic ulcer diagnosis was studied. The prevalence of abdominal pain alleviated by food intake was 12% among bus drivers and 6% in the reference group. The incidence of hospital discharge with duodenal ulcer among younger bus drivers was twice the incidence among Danish...

76 FR 37184 - Discretionary Bus and Bus Facilities Program

Science.gov (United States)

2011-06-24

... transporting bicycles on public transportation vehicles. The FY 2011 Appropriations Act allows a 90 percent Federal share for the total cost of a biodiesel bus. The Act also allows a 90 percent Federal share for...

Fitness to drive among commercial intercity drivers in Benin-City ...

African Journals Online (AJOL)

Background: Unfit drivers are prone to road traffic accident, therefore their health is paramount in ensuring the safety of road users. To determine the fitness to drive among commercial intercity bus drivers in Benin City, Edo State Material and methods: A descriptive cross-sectional study was conducted among 194 ...

San Antonio's 1983 Bus Passenger Survey

Science.gov (United States)

1983-10-01

Many transit operators routinely collect ridership data in order to provide a : basis for the planning of bus services. Often a survey is conducted of bus : riders to determine their riding habits, their views about the quality of : current service, ...

Scenario-based electric bus operation: A case study of Putrajaya, Malaysia

Directory of Open Access Journals (Sweden)

Lay Eng Teoh

2018-03-01

Full Text Available Globally, transportation sector has emerged as one of the major sources of air pollution. Correspondingly, green mobility (with electric bus is gaining increasing attention as an essential step to mitigate emission concern. As such, a proper electric bus network design and fleet planning is important especially for bus operator to acquire an adequate number of electric bus, right on time, in order to operate electric bus system viably. Thus, this paper aims to examine the possibility to operate electric bus as a replacement for the conventional bus operation (with natural gas buses for the study area in Putrajaya, Malaysia. In order to determine a proper-designed electric bus operating system in terms of electric bus route, service frequency and quantity, the proposed methodology is developed with the aid of a traffic modeling software to cater various scenarios. Based on the existing (conventional traffic and transit system in Putrajaya, the developed electric bus operating model is calibrated accordingly by considering various operational concerns including battery capacity and charging facility. The resultant findings revealed that the developed electric bus operating system in Putrajaya outperforms the conventional bus operation, not only in generating a higher profit margin for the bus operator, but also satisfying the passengers in a better manner (by carrying more passengers per unit of bus with a lower energy consumption.

PyBus -- A Python Software Bus

OpenAIRE

Lavrijsen, W

2005-01-01

A software bus, just like its hardware equivalent, allows for the discovery, installation, configuration, loading, unloading, and run-time replacement of software components, as well as channeling of inter-component communication. Python, a popular open-source programming language, encourages a modular design on software written in it, but it offers little or no component functionality. However, the language and its interpreter provide sufficient hooks to implement a thin, integral layer...

49 CFR 393.24 - Requirements for head lamps, auxiliary driving lamps and front fog lamps.

Science.gov (United States)

2010-10-01

... Devices, and Electrical Wiring § 393.24 Requirements for head lamps, auxiliary driving lamps and front fog lamps. (a) Headlamps. Every bus, truck and truck tractor shall be equipped with headlamps as required by...

Relationships of working conditions, health problems and vehicle accidents in bus rapid transit (BRT) drivers.

Science.gov (United States)

Gómez-Ortiz, Viviola; Cendales, Boris; Useche, Sergio; Bocarejo, Juan P

2018-04-01

The aim of this study was to estimate accident risk rates and mental health of bus rapid transit (BRT) drivers based on psychosocial risk factors at work leading to increased stress and health problems. A cross-sectional research design utilized a self-report questionnaire completed by 524 BRT drivers. Some working conditions of BRT drivers (lack of social support from supervisors and perceived potential for risk) may partially explain Bogota's BRT drivers' involvement in road accidents. Drivers' mental health problems were associated with higher job strain, less support from co-workers, fewer rewards and greater signal conflict while driving. To prevent bus accidents, supervisory support may need to be increased. To prevent mental health problems, other interventions may be needed such as reducing demands, increasing job control, reducing amount of incoming information, simplifying current signals, making signals less contradictory, and revising rewards. © 2018 Wiley Periodicals, Inc.

Case Study - Propane School Bus Fleets

Energy Technology Data Exchange (ETDEWEB)

Laughlin, M; Burnham, A.

2014-08-31

As part of the U.S. Department of Energy’s (DOE’s) effort to deploy transportation technologies that reduce U.S. dependence on imported petroleum, this study examines five school districts, one in Virginia and four in Texas, successful use of propane school buses. These school districts used school buses equipped with the newly developed liquid propane injection system that improves vehicle performance. Some of the school districts in this study saved nearly 50% on a cost per mile basis for fuel and maintenance relative to diesel. Using Argonne National Laboratory’s Alternative Fuel Life-Cycle Environmental and Economic Transportation (AFLEET) Tool developed for the DOE’s Clean Cities program to help Clean Cities stakeholders estimate petroleum use, greenhouse gas (GHG) emissions, air pollutant emissions and cost of ownership of light-duty and heavy-duty vehicles, the results showed payback period ranges from 3—8 years, recouping the incremental cost of the vehicles and infrastructure. Overall, fuel economy for these propane vehicles is close to that of displaced diesel vehicles, on an energy-equivalent basis. In addition, the 110 propane buses examined demonstrated petroleum displacement, 212,000 diesel gallon equivalents per year, and GHG benefits of 770 tons per year.

Security awareness for public bus transportation : case studies of attacks against the Israeli public bus system [research brief].

Science.gov (United States)

2012-03-01

Government regulators and transportation operators of public bus systems are concerned about terrorist attacks. Bus attacks in Israel between late September 2000 and the end of 2006, a period known as the Second Intifada, are particularly well known....

Emissions of toxic pollutants from compressed natural gas and low sulfur diesel-fueled heavy-duty transit buses tested over multiple driving cycles.

Science.gov (United States)

Kado, Norman Y; Okamoto, Robert A; Kuzmicky, Paul A; Kobayashi, Reiko; Ayala, Alberto; Gebel, Michael E; Rieger, Paul L; Maddox, Christine; Zafonte, Leo

2005-10-01

The number of heavy-duty vehicles using alternative fuels such as compressed natural gas (CNG) and new low-sulfur diesel fuel formulations and equipped with after-treatment devices are projected to increase. However, few peer-reviewed studies have characterized the emissions of particulate matter (PM) and other toxic compounds from these vehicles. In this study, chemical and biological analyses were used to characterize the identifiable toxic air pollutants emitted from both CNG and low-sulfur-diesel-fueled heavy-duty transit buses tested on a chassis dynamometer over three transient driving cycles and a steady-state cruise condition. The CNG bus had no after-treatment, and the diesel bus was tested first equipped with an oxidation catalyst (OC) and then with a catalyzed diesel particulate filter (DPF). Emissions were analyzed for PM, volatile organic compounds (VOCs; determined on-site), polycyclic aromatic hydrocarbons (PAHs), and mutagenic activity. The 2000 model year CNG-fueled vehicle had the highest emissions of 1,3-butadiene, benzene, and carbonyls (e.g., formaldehyde) of the three vehicle configurations tested in this study. The 1998 model year diesel bus equipped with an OC and fueled with low-sulfur diesel had the highest emission rates of PM and PAHs. The highest specific mutagenic activities (revertants/microg PM, or potency) and the highest mutagen emission rates (revertants/mi) were from the CNG bus in strain TA98 tested over the New York Bus (NYB) driving cycle. The 1998 model year diesel bus with DPF had the lowest VOCs, PAH, and mutagenic activity emission. In general, the NYB driving cycle had the highest emission rates (g/mi), and the Urban Dynamometer Driving Schedule (UDDS) had the lowest emission rates for all toxics tested over the three transient test cycles investigated. Also, transient emissions were, in general, higher than steady-state emissions. The emissions of toxic compounds from an in-use CNG transit bus (without an oxidation

Task Analysis Assessment on Intrastate Bus Traffic Controllers

Science.gov (United States)

Yen Bin, Teo; Azlis-Sani, Jalil; Nur Annuar Mohd Yunos, Muhammad; Ismail, S. M. Sabri S. M.; Tajedi, Noor Aqilah Ahmad

2016-11-01

Public transportation acts as social mobility and caters the daily needs of the society for passengers to travel from one place to another. This is true for a country like Malaysia where international trade has been growing significantly over the past few decades. Task analysis assessment was conducted with the consideration of cognitive ergonomic view towards problem related to human factors. Conducting research regarding the task analysis on bus traffic controllers had allowed a better understanding regarding the nature of work and the overall monitoring activities of the bus services. This paper served to study the task analysis assessment on intrastate bus traffic controllers and the objectives of this study include to conduct task analysis assessment on the bus traffic controllers. Task analysis assessment for the bus traffic controllers was developed via Hierarchical Task Analysis (HTA). There are a total of five subsidiary tasks on level one and only two were able to be further broken down in level two. Development of HTA allowed a better understanding regarding the work and this could further ease the evaluation of the tasks conducted by the bus traffic controllers. Thus, human error could be reduced for the safety of all passengers and increase the overall efficiency of the system. Besides, it could assist in improving the operation of the bus traffic controllers by modelling or synthesizing the existing tasks if necessary.

New drive axles for hybrid applications in low-floor city busses. The electric axle AVE 130; Neue Antriebsachse fuer Hybridapplikationen in Niederflur-Stadtbussen. Die Elektroachse AVE 130

Energy Technology Data Exchange (ETDEWEB)

Solka, Ulrich [ZF Passau GmbH (Germany); Mueller, Axel M. [ZF Friedrichshafen AG (Germany)

2009-07-01

The contribution under consideration reports on the mechanically constructional structure of the electrically driven low-floor axle AVE 130 of ZF Friedrichshafen AG (Friedrichshafen, Federal Republic of Germany). The characteristics of the electric drive are presented with the particularities of the implemented asynchronous machine and the road performances which can be developed by a city bus using this axle. Also the system characteristics of a hybrid bus with serial hybrid drive system concerning to aggregate arrangement, mass balances and the interaction of the aggregates in the drive briefly are discussed. The results of numerical simulation regarding fuel saving potential in these systems round the remarks off.

Whole-body Vibration Exposure Intervention among Professional Bus and Truck Drivers: A Laboratory Evaluation of Seat-suspension Designs.

Science.gov (United States)

Blood, Ryan P; Yost, Michael G; Camp, Janice E; Ching, Randal P

2015-01-01

Long-term exposure to seated whole-body vibration (WBV) is one of the leading risk factors for the development of low back disorders. Professional bus and truck drivers are regularly exposed to continuous WBV, since they spend the majority of their working hours driving heavy vehicles. This study measured WBV exposures among professional bus and truck drivers and evaluated the effects of seat-suspension designs using simulated field-collected data on a vibration table. WBV exposures were measured and compared across three different seat designs: an air-ride bus seat, an air-ride truck seat, and an electromagnetically active (EM-active) seat. Air-ride seats use a compressed-air bladder to attenuate vibrations, and they have been in operation throughout the transportation industry for many years. The EM-active seat is a relatively new design that incorporates a microprocessor-controlled actuator to dampen vibration. The vibration table simulated seven WBV exposure scenarios: four segments of vertical vibration and three scenarios that used field-collected driving data on different road surfaces-a city street, a freeway, and a section of rough roadway. The field scenarios used tri-axial WBV data that had been collected at the seat pan and at the driver's sternum, in accordance with ISO 2631-1 and 2631-5. This study found that WBV was significantly greater in the vertical direction (z-axis) than in the lateral directions (x-and y-axes) for each of the three road types and each of the three types of seats. Quantitative comparisons of the results showed that the floor-to-seat-pan transmissibility was significantly lower for the EM-active seat than for either the air-ride bus seat or the air-ride truck seat, across all three road types. This study also demonstrated that seat-suspension designs have a significant effect on the vibrations transmitted to vehicle operators, and the study's results may prove useful in designing future seat suspensions.

An evaluation of a lane support system for bus rapid transit on narrow shoulders and the relation to bus driver mental workload

NARCIS (Netherlands)

Ward, Nicholas J.; Shankwitz, Craig; Gorgestani, Alec; Donath, Max; De Waard, Dick; Boer, Erwin R.

2006-01-01

The use of dedicated bus shoulders is a key method for implementing bus rapid transit (BRT) in areas that do not have the space for additional infrastructure. However, the narrow width of the bus shoulder and the need to anticipate traffic hazards in the adjacent lane can both be significant

SISTEM RESERVASI TIKET BUS DI TERMINAL ARJOSARI MALANG

Directory of Open Access Journals (Sweden)

Surya Wirawan

2013-10-01

Full Text Available Bus Ticket Reservation System is an application that can be used to help booking bus tickets and the buyer will get a report via SMS Gateway. The reservation system is made by conducting field studies in Arjosari Bus Station Malang. This system uses SMS Gateway to send the report to the buyer after booking bus tickets online. SMS Gateway on this application serves as a liaison which delays sms between External Short Message entitiy (ESME and Short Message Service Center (SMSC and so does in reserve.The reservation system made is developed with the PHP programming language and has a prototype system pattern. System functions were tested using the validation testing, performance testing, and usability testing. The results percentage of responses usability testing is 67.7%. This shows that Ticket Reservation System at Arjosari Bus Station can be used well enough.

Simulation of Trolleybus Traction Induction Drive With Supercapacitor Energy Storage System

Science.gov (United States)

Brazis, V.; Latkovskis, L.; Grigans, L.

2010-01-01

The article considers the possibilities of saving the regenerative braking energy in Škoda 24Tr type trolleybuses by installing the onboard supercapacitor energy storage system (ESS) and improving its performance with automated switching to the autonomous traction mode. Proposed is an ESS control system with constant DC bus voltage in the supercapacitor charging mode and supercapacitor current proportional to the AC drive current in the discharging mode. The authors investigate stability of the trolleybus ESS control system operating together with AC traction drive in various overhead voltage failure modes. The co-simulation of ESS operation was done by Matlab/Simulink AC drive and PSIM ESS continuous models.

Extracting potential bus lines of Customized City Bus Service based on public transport big data

Science.gov (United States)

Ren, Yibin; Chen, Ge; Han, Yong; Zheng, Huangcheng

2016-11-01

Customized City Bus Service (CCBS) can reduce the traffic congestion and environmental pollution that caused by the increasing in private cars, effectively. This study aims to extract the potential bus lines and each line's passenger density of CCBS by mining the public transport big data. The datasets used in this study are mainly Smart Card Data (SCD) and bus GPS data of Qingdao, China, from October 11th and November 7th 2015. Firstly, we compute the temporal-origin-destination (TOD) of passengers by mining SCD and bus GPS data. Compared with the traditional OD, TOD not only has the spatial location, but also contains the trip's boarding time. Secondly, based on the traditional DBSCAN algorithm, we put forwards an algorithm, named TOD-DBSCAN, combined with the spatial-temporal features of TOD.TOD-DBSCAN is used to cluster the TOD trajectories in peak hours of all working days. Then, we define two variables P and N to describe the possibility and passenger destiny of a potential CCBS line. P is the probability of the CCBS line. And N represents the potential passenger destiny of the line. Lastly, we visualize the potential CCBS lines extracted by our procedure on the map and analyse relationship between potential CCBS lines and the urban spatial structure.

Predicting self-pollution inside school buses using a CFD and multi-zone coupled model

Science.gov (United States)

Li, Fei; Lee, Eon S.; Liu, Junjie; Zhu, Yifang

2015-04-01

The in-cabin environment of a school bus is important for children's health. The pollutants from a bus's own exhaust contribute to children's overall exposure to air pollutants inside the school bus cabin. In this study, we adapted a coupled model originally developed for indoor environment to determine the relative contribution of the bus own exhaust to the in-cabin pollutant concentrations. The coupled model uses CFD (computational fluent dynamics) model to simulate outside concentration and CONTAM (a multi-zone model) for inside the school bus. The model was validated with experimental data in the literature. Using the validated model, we analyzed the effects of vehicle speed and tailpipe location on self-pollution inside the bus cabin. We confirmed that the pollution released from the tailpipe can penetrate into the bus cabin through gaps in the back emergency door. We found the pollution concentration inside school buses was the highest when buses were driven at a medium speed. In addition, locating the tailpipe on the side, behind the rear axle resulted in less self-pollution since there is less time for the suction effect to take place. The developed theoretical framework can be generalized to study other types of buses. These findings can be used in developing policy recommendations for reducing human exposure to air pollution inside buses.

Integration of refrigerators into facility automation with the aid of bus systems; Integration der Kaeltetechnik in die Gebaeudeautomation mit Bus-Systemen

Energy Technology Data Exchange (ETDEWEB)

Baumgarth, S.; Heiser, M. [Fachhochschule Braunschweig-Wolfenbuettel, Wolfenbuettel (DE). Inst. fuer Verbrennungstechnik und Prozessautomation (IVP)

2000-07-01

The integration of refrigeration systems in building automation is illustrated by the example of a ventilation system and a cooling ceiling. Cold is supplied by a coldwater unit. This necessitates supply of consumption data to the central refrigeration system. So far, technical facilities are commonly controlled by DDC systems and in-house bus systems. The demand for open communication between different systems resulted in the development of neutral systems like FND and Profibus, which were followed by a multitude of other, less generally accepted systems. In the field of electrical installations, the European Installation Bus EIB was generally accepted as a certified, open bus system which can be combined with DDC technology and integrated in in-house control systems. Another technology developed in the USA is the Local Operating Network, LON, whic has a hither transmission rate and higher information content for the various bus members. The contribution compares the two bus systems. [German] Die Einbindung der Kaeltetechnik in die Gebaeudeautomation wird an den Beispielen Lueftungsanlage und Kuehldecke vorgestellt. Die erforderliche Kaelte soll durch einen Kaltwasserersatz energieoptimiert bereitgestellt werden. Dazu muessen Informationen aus dem Verbraucherbereich in der Kaeltezentrale zur Verfuegung stehen. RTL-Anlagen wurden bisher mittels DDC-Technik und firmenspezifischen Bus-Systemen geregelt und gesteuert. Wenn verschiedene Anlagen durch DDC-Systeme unterschiedlicher Hersteller betrieben wurden, so war anfaenglich eine gemeinsame Ueberwachung auf einer zentralen Leitwarte nur ueber Gateways moeglich. Aus der Forderung nach offener Kommunikation unterschiedlicher Systeme entstanden die ersten firmenneutralen Entwicklungen FND und Profibus. Es folgten eine Vielzahl weiterer Netz- und Busdefinitionen und deren Kommunikationsprotokolle, denen jedoch weitgehend eine allgemeine Anerkennung versagt blieb. Im Bereich der Elektroinstallation profilierte sich der

Classifying the Diversity of Bus Mapping Systems

Science.gov (United States)

Said, Mohd Shahmy Mohd; Forrest, David

2018-05-01

This study represents the first stage of an investigation into understanding the nature of different approaches to mapping bus routes and bus network, and how they may best be applied in different public transport situations. In many cities, bus services represent an important facet of easing traffic congestion and reducing pollution. However, with the entrenched car culture in many countries, persuading people to change their mode of transport is a major challenge. To promote this modal shift, people need to know what services are available and where (and when) they go. Bus service maps provide an invaluable element of providing suitable public transport information, but are often overlooked by transport planners, and are under-researched by cartographers. The method here consists of the creation of a map evaluation form and performing assessment of published bus networks maps. The analyses were completed by a combination of quantitative and qualitative data analysis of various aspects of cartographic design and classification. This paper focuses on the resulting classification, which is illustrated by a series of examples. This classification will facilitate more in depth investigations into the details of cartographic design for such maps and help direct areas for user evaluation.

CFD Investigation on Long-Haul Passenger Bus

Science.gov (United States)

Tan, C. F.; Tee, B. T.; Law, H. C.; Lim, T. L.

2015-09-01

Air flow distribution is one of the important factors that will influence the bus passenger comfort during long haul travel. Poor air flow distribution not only cause discomfort to the bus passenger but also influence their travel mode as well. The main purpose of this study is to investigate the air flow performance of the bus air-conditioning system through CFD simulation approach. A 3D CAD model of air ducts was drawn and hence analysed by using CFD software, namely ANSYS Fluent, to determine the airflow rate for every outlets of the air-conditioning system. The simulated result was then validated with experimental data obtained from prototype model of air duct. Based on the findings, new design concepts is proposed with the aim to meet the industry requirement as well as to improve the bus passenger comfort during long haul travel.

Program Guide for Diesel Engine Mechanics 8742000 (IN47.060500) and Heavy Duty Truck and Bus Mechanics DIM0991 (IN47.060501).

Science.gov (United States)

University of South Florida, Tampa. Coll. of Education.

This competency-based program guide provides course content information and procedures for secondary schools, postsecondary vocational schools, and community colleges in Florida that conduct programs in diesel engine mechanics and heavy duty truck and bus mechanics. The first section is on legal authority, which applies to all vocational education…

1393 Ring Bus at JPL: Description and Status

Science.gov (United States)

Wysocky, Terry R.

2007-01-01

Completed Ring Bus IC V&V Phase - Ring Bus Test Plan Completed for SIM Project - Applicable to Other Projects Implemented a Avionics Bus Based upon the IEEE 1393 Standard - Excellent Starting Point for a General Purpose High-Speed Spacecraft Bus - Designed to Meet SIM Requirements for - Real-time deterministic, distributed systems. - Control system requirements - Fault detection and recovery Other JPL Projects Considering Implementation F'light Software Ring Bus Driver Module Began in 2006, Continues Participating in Standard Revision. Search for Earth-like planets orbiting nearby stars and measure the masses and orbits of the planets it finds. Survey 2000 nearby stars for planetary systems to learn whether our Solar System is unusual, or typical. Make a new catalog of star position 100 times more accurate than current measurements. Learn how our galaxy formed and will evolve by studying the dynamics of its stars. Critically test models of exactly how stars shine, including exotic objects like black holes, neutron stars and white dwarfs.

Rancang Bangun Sistem Pemesanan Tiket Bus Kupang-Atambua Berbasis SMS Gateway

Directory of Open Access Journals (Sweden)

Emerensiana Ngaga

2016-11-01

Full Text Available Bus merupakan alat transportasi yang paling banyak digunakan masyarakat karena harga yang murah dan masih terjangkau untuk masyarakat kalangan ekonomi menengah ke bawah.  Umumnya pemesanan tiket bus dilakukan dengan mendatangi langsung tempat penjualan tiket bus atau dengan cara menelepon ke kantor agen. Proses pemesanan seperti ini  memiliki kekurangan dimana pegawai kerepotan dalam mencatat dan seringkali terjadi kesalahan dalam mencatat pemesanan tiket. Sedangkan untuk waktu pemesanan, umumnya calon penumpang melakukan pemesanan tiket, satu atau dua hari sebelum keberangkatan dan ada juga yang tidak sempat memesan tiket beberapa hari sebelumnya dan melakukan pembelian tiket pada hari keberangkatan sehingga sering kali tidak mendapatkan tiket. Penelitian ini bertujuan merancang bangun sistem pemesanan tiket bus berbasis SMS Gateway yang memberikan kemudahan layanan pemesanan tiket bus bagi masyarakat secara jarak jauh serta kemudahan mengetahui informasi penjadwalan bus dengan cepat. Aplikasi dibangun menggunakan metode Unified Process, dengan bahasa pemrograman Java NetBeansIDE 7.3.1, MySQL sebagai database dan Gammu sebagai software untuk membantu pembangunan aplikasi SMS Gateway. Hasil dari penelitian ini adalah sebuah sistem pemesanan tiket bus yang memberikan alternatif baru proses pemesanan tiket bus secara baik tanpa ada permasalahan jarak dan waktu. Selain itu masyarakat juga dapat mengetahui informasi jadwal bus, harga tiket dan juga informasi bila terjadi perubahan jadwal keberangkatan bus.   Kata kunci— Bus, Tiket, SMS Gateway, Unified Process

Evaluation of Urban Bus Transport Failure in Gujranwala City of Pakistan

Directory of Open Access Journals (Sweden)

MUHAMMAD WAQAR ASLAM

2017-07-01

Full Text Available This research work has evaluated the performance of urban public bus transport service operating in Gujranwala city of Pakistan. The assessment has been made in terms of financial viability, bus condition, operational performance and user perception. Based on the data requirements, various traffic/transport surveys were conducted including Passenger Boarding and Alighting Survey, Bus Count Survey, Bus Inspection Survey, Illegal Operations Survey and Public Transport User Interview Survey in consultation with concerned department/agencies. Field surveys were also conducted to get input from passengers and local people. Initial investigation informed that out of four operational bus routes, only two routes are profitable. The overall bus operation is running in loss (only 0.3% net profit. It has barely any profit for the bus operator against its investment thereby making the urban bus operation financially non-viable. The whole revenue flow is dependent on passenger ticketing revenue only. Around 35% of the buses are in poor condition with major issues of quality of tyres, no speedometer, worse condition of seats, floor and ceiling, and display of route. Illegal operation of Qingqis/Rickshaws (as para-transit mode along the bus routes is also decreasing the revenue by capturing the passenger volume. According to passenger opinion analysis, around 55% of the passenger are not satisfied with the service quality and prefer other modes of transport. Their major concerns are absence of facilities for disables and bus stops, bus seating and standing capacity, poor bus condition and pick pocketing. Collectively, these factors are contributing

Circuit breaker and bus

International Nuclear Information System (INIS)

Vogel, H.F.

1978-01-01

Two close-open operations are required each pulse cycle at approximately 3 MA with the breaker in series with the burn supply, both forming a leg in parallel with the E-coil and the homopolar. To conduct the 3-MA current, approximately 30 breaker units are connected in parallel. Each unit is equipped with a counterpulse capacitor bank, and the bus for the 30 units is provided with a common saturable reactor core made of strip steel wound around the bus. Oil breakers of a special design are chosen because of their high arc resistance facilitating the current transfer to the homopolar machine and for obtaining precision timing in opening and closing of the contacts. The precision timing is achieved by a shock wave method with the oil serving as hydraulic medium. Each of the parallel breaker units possesses two sets of contacts, a stationary and a transient one. A 1-mΩ resistor in series with the transient contacts of each breaker unit is to improve the current sharing. The bus consists of room temperature copper, stranded and transposed to help provide current equalization under transient conditions

Managing Food Allergies at School: School Transportation Staff

Centers for Disease Control (CDC) Podcasts

2015-01-20

This podcast highlights the role of bus drivers and transportation staff in the management of food allergies in schools. It also identifies CDC food allergy resources for schools.  Created: 1/20/2015 by National Center for Chronic Disease Prevention and Health Promotion (NCCDPHP).   Date Released: 1/20/2015.

Design Report for Isolated RS-485 Bus Node

Science.gov (United States)

2016-07-01

TERMS Android , RS-485, isolated, USB, smartphone 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18. NUMBER...controlled wired RS-485 network. The Android -based smartphone or tablet is used in conjunction with a USB to serial bridge to operate as the bus master in...the system. The Android device operates in USB Host mode and communicates to the RS-485 bus as if a single peripheral on the USB bus. 15. SUBJECT

Scenario-based electric bus operation: A case study of Putrajaya, Malaysia

OpenAIRE

Lay Eng Teoh; Hooi Ling Khoo; Siew Yoke Goh; Lai Mun Chong

2018-01-01

Globally, transportation sector has emerged as one of the major sources of air pollution. Correspondingly, green mobility (with electric bus) is gaining increasing attention as an essential step to mitigate emission concern. As such, a proper electric bus network design and fleet planning is important especially for bus operator to acquire an adequate number of electric bus, right on time, in order to operate electric bus system viably. Thus, this paper aims to examine the possibility to oper...

DIMETHYL ETHER (DME)-FUELED SHUTTLE BUS DEMONSTRATION PROJECT

Energy Technology Data Exchange (ETDEWEB)

Elana M. Chapman; Shirish Bhide; Jennifer Stefanik; Howard Glunt; Andre L. Boehman; Allen Homan; David Klinikowski

2003-04-01

The objectives of this research and demonstration program are to convert a campus shuttle bus to operation on dimethyl ether, a potential ultra-clean alternative diesel fuel. To accomplish this objective, this project includes laboratory evaluation of a fuel conversion strategy, as well as, field demonstration of the DME-fueled shuttle bus. Since DME is a fuel with no lubricity (i.e., it does not possess the lubricating quality of diesel fuel), conventional fuel delivery and fuel injection systems are not compatible with dimethylether. Therefore, to operate a diesel engine on DME one must develop a fuel-tolerant injection system, or find a way to provide the necessary lubricity to the DME. In this project, they have chosen the latter strategy in order to achieve the objective with minimal need to modify the engine. The strategy is to blend DME with diesel fuel, to obtain the necessary lubricity to protect the fuel injection system and to achieve low emissions. The bulk of the efforts over the past year were focused on the conversion of the campus shuttle bus. This process, started in August 2001, took until April 2002 to complete. The process culminated in an event to celebrate the launching of the shuttle bus on DME-diesel operation on April 19, 2002. The design of the system on the shuttle bus was patterned after the system developed in the engine laboratory, but also was subjected to a rigorous failure modes effects analysis with help from Dr. James Hansel of Air Products. The result of this FMEA was the addition of layers of redundancy and over-pressure protection to the system on the shuttle bus. The system became operation in February 2002. Preliminary emissions tests and basic operation of the shuttle bus took place at the Pennsylvania Transportation institute's test track facility near the University Park airport. After modification and optimization of the system on the bus, operation on the campus shuttle route began in early June 2002. However, the

Status of the IEEE P896 Future Backplane Bus

International Nuclear Information System (INIS)

Gustavson, D.B.

1983-10-01

The IEEE P896 Future Backplane Bus project has been influenced by and has influenced FASTBUS and several other contemporary bus designs. This paper summarizes the current status of that project, which is directed toward the needs of modern 32-bit microprocessor systems with multiple processors. Some of the technology developed for P896 will be important for future non-ECL implementations of FASTBUS and other buses. In particular, new bus drivers and receivers should greatly improve the performance and reliability of backplane buses and cable buses. The current status of the P896 serial bus is also summarized

The Software Bus, an Object-Oriented Data Exchange System

International Nuclear Information System (INIS)

Akerbaek, T.; Louka, M.

1996-01-01

This document describes the Software Bus System, developed for object-oriented task to task communication in a TCP/IP based network. The Software Bus is a set of library functions, developed to be used for the Picasso-3 UIMS, and as a general purpose tool for dynamically interfacing programs at run-time. The Software Bus offers a high level object-oriented data exchange mechanism that relieves the application programmer of the low level TCP/IP-programming and communication protocol handling. The Software Bus is currently available under several UNIX platforms and a version for Windows NT is planned for late 1996. (author)

Fuel Cell Electric Bus Evaluations | Hydrogen and Fuel Cells | NREL

Science.gov (United States)

Bus Evaluations Fuel Cell Electric Bus Evaluations NREL's technology validation team evaluates fuel cell electric buses (FCEBs) to provide comprehensive, unbiased evaluation results of fuel cell bus early transportation applications for fuel cell technology. Buses operate in congested areas where

Schedule and complex motion of shuttle bus induced by periodic inflow of passengers

International Nuclear Information System (INIS)

Nagatani, Takashi; Naito, Yuichi

2011-01-01

We have studied the dynamic behavior of a bus in the shuttle bus transportation with a periodic inflow. A bus schedule is closely related to the dynamics. We present the modified circle map model for the dynamics of the shuttle bus. The motion of the shuttle bus depends on the loading parameter and the inflow period. The shuttle bus displays the periodic, quasi-periodic, and chaotic motions with varying both loading parameter and inflow rate. -- Highlights: → We studied the dynamic behavior of a bus in the shuttle bus transportation. → We presented the modified circle map model for the bus schedule. → We clarified the dependence of the tour time on both loading parameter and inflow period.

MIL-STD-1553 dynamic bus controller/remote terminal hybrid set

Science.gov (United States)

Friedman, S. N.

This paper describes the performance, physical and electrical requirements of a Dual Redundant BUS Interface Unit (BIU) acting as a BUS Controller Interface Unit (BCIU) or Remote Terminal Unit (RTU) between a Motorola 68000 VME BUS and MIL-STD-1553B Multiplex Data Bus. A discussion of how the BIU Hybrid set is programmed, and operates as a BCIU or RTU, will be included. This paper will review Dynamic Bus Control and other Mode Code capabilities. The BIU Hybrid Set interfaces to a 68000 Microprocessor with a VME Bus using programmed I/O transfers. This special interface will be discussed along with the internal Dual Access Memory (4K x 16) used to support the data exchanges between the CPU and the BIU Hybrid Set. The hybrid set's physical size and power requirements will be covered. This includes the present Double Eurocard the BIU function is presently being offered on.

Global Optimization for Bus Line Timetable Setting Problem

Directory of Open Access Journals (Sweden)

Qun Chen

2014-01-01

Full Text Available This paper defines bus timetables setting problem during each time period divided in terms of passenger flow intensity; it is supposed that passengers evenly arrive and bus runs are set evenly; the problem is to determine bus runs assignment in each time period to minimize the total waiting time of passengers on platforms if the number of the total runs is known. For such a multistage decision problem, this paper designed a dynamic programming algorithm to solve it. Global optimization procedures using dynamic programming are developed. A numerical example about bus runs assignment optimization of a single line is given to demonstrate the efficiency of the proposed methodology, showing that optimizing buses’ departure time using dynamic programming can save computational time and find the global optimal solution.

32 CFR 935.138 - Motor bus operation.

Science.gov (United States)

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Motor bus operation. 935.138 Section 935.138 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE TERRITORIAL AND INSULAR REGULATIONS WAKE ISLAND CODE Motor Vehicle Code § 935.138 Motor bus operation. Each person operating a motor...

Motor Integrated Variable Speed Drives

DEFF Research Database (Denmark)

Singh, Yash Veer

rectifier at the front end is presented in this thesis and requirements of a buffer stage in the form of ESI is explained in detail. An equivalent circuit and linear model are developed to give the transfer function and control of the ESI based three-phase rectifier. In this thesis a power converter...... with ESI is designed and tested with standard induction motor to verify functionality of a working drive. One modified version of the ESI based converter has also been looked into to reduce losses of converter, but because of difficulties in reducing the bus-bar inductance in that design, further...

The seated bus passenger--a review.

Science.gov (United States)

Levis, J A

1978-09-01

The paper describes the inter-relationship of anthropometry, rig studies and dynamic testing of aspects related to problems of the seated bus passenger. It seeks to draw together sub-sections of a very large study sponsored by the government through the Transport and Road Research Laboratory and undertaken by the Human Factors Group of Leyland Truck and Bus. It is relevant to all those designing passenger carrying transport systems.

Cellular Automata Based Modeling for Evaluating Different Bus Stop Designs in China

Directory of Open Access Journals (Sweden)

Haoyang Ding

2015-01-01

Full Text Available A cellular automaton model is proposed to simulate mixed traffic flow composed of motor vehicles and bicycles near bus stops. Three typical types of bus stops which are common in China are considered in the model, including two types of curbside bus stops and one type of bus bay stops. Passenger transport capacity of three types of bus stops, which is applied to evaluate the bus stop design, is calculated based on the corresponding traffic flow rate. According to the simulation results, the flow rates of both motor vehicles and bicycles exhibit phase transition from free flow to the saturation one at the critical point. The results also show that the larger the interaction between motor vehicle and bicycle flow is near curbside bus stops, the more the value of saturated flows drops. Curbside bus stops are more suitable when the conflicts between two flows are small and the inflow rate of motor vehicles is low. On the contrary, bus bay stops should be applied due to their ability to reduce traffic conflicts. Findings of this study can provide useful suggestions on bus stop selection considering different inflow rate of motor vehicles and bicycles simultaneously.

Environmental Assessment of Bus Transport in the Trondheim Region - Evaluation of Relevant Bus and Fuel Technologies and their Potential for Mitigating Emissions from Passenger Transportation

OpenAIRE

Buø, Tonje

2015-01-01

The overall aim of this thesis is to assess the carbon footprint of transport by bus in the Trondheim region. Bus transportation is promoted as a strategy both to combat local pollution problems in urban areas and to mitigate global greenhouse gas emissions from passenger transport. Still, the environmental impacts of bus transport have received fairly limited attention in research. The environmental impacts of bus transport are calculated through life cycle assessment. A model is develo...

Countermeasures for Developing New Energy Bus Standards in China

Science.gov (United States)

Shi, Xin

2018-01-01

With the rapid development of new energy vehicle technology, new energy bus has become more and more popular in China, and the relevant standards and policy are urgently needed to guide the market. According to the assessment of the development situation on new energy vehicle technology and new energy bus, combing with traffic policy guidance and the development trend of new energy vehicles, this paper aims to put forward the countermeasures of the new energy bus standard in China, including standard system, key standards and relevant recommendations. Research result is expected to provide decision support for the wide application of new energy bus in China.

Speed limiter integrated fatigue analyzer (SLIFA) for speed and fatigue control on diesel engine truck and bus

Science.gov (United States)

Wahyudi, Haris; Pranoto, Hadi; Leman, A. M.; Sebayang, Darwin; Baba, I.

2017-09-01

Every second, the number of road traffic deaths is increased globally with millions more sustaining severe injuries and living with long-term adverse health consequences. Jakarta alone in year 2015 had recorded 556 people died due to road accidents, approximately reached 6.231 road accident cases. The identified major contributory factors of such unfortunate events are both driver fatigue and over speeding habit especially related to the driving of truck and bus. This paper presents the idea on how to control the electronic system from input fuel system of injection pump and the combustion chamber engine will control the valve solenoid in injection pump which can lock and fuel will stop for moment, and speed limit can be success, by using sensor heart rate we can input reduce speed limit when fatigue detection driver. Integration process this tool can be relevant when Speed Limiter Integrated Fatigue Analyser (SLIFA) trial in the diesel engine for truck and bus, the result of this research Speed Limiter Integrated Fatigue Analyser (SLIFA) able to control speed of diesel engine for truck and bus almost 30km/h, 60km/h, and until 70 km/h. The installation of the sensor heart rate as the input speed limit SLIFA would work when the driver is detected to be in the fatigue condition. We make Speed Limiter Integrated Fatigue Analyser (SLIFA) for control and monitoring system for diesel engine in truck and bus. Speed Limiter Integrated Fatigue Analyser (SLIFA) system can save the historical of the speed record, fatigue, rpm, and body temperature of the driver.

Effects of passengers on bus driver celeration behavior and incident prediction.

Science.gov (United States)

Af Wåhlberg, A E

2007-01-01

Driver celeration (speed change) behavior of bus drivers has previously been found to predict their traffic incident involvement, but it has also been ascertained that the level of celeration is influenced by the number of passengers carried as well as other traffic density variables. This means that the individual level of celeration is not as well estimated as could be the case. Another hypothesized influence of the number of passengers is that of differential quality of measurements, where high passenger density circumstances are supposed to yield better estimates of the individual driver component of celeration behavior. Comparisons were made between different variants of the celeration as predictor of traffic incidents of bus drivers. The number of bus passengers was held constant, and cases identified by their number of passengers per kilometer during measurement were excluded (in 12 samples of repeated measurements). After holding passengers constant, the correlations between celeration behavior and incident record increased very slightly. Also, the selective prediction of incident record of those drivers who had had many passengers when measured increased the correlations even more. The influence of traffic density variables like the number of passengers have little direct influence on the predictive power of celeration behavior, despite the impact upon absolute celeration level. Selective prediction on the other hand increased correlations substantially. This unusual effect was probably due to how the individual propensity for high or low celeration driving was affected by the number of stops made and general traffic density; differences between drivers in this respect were probably enhanced by the denser traffic, thus creating a better estimate of the theoretical celeration behavior parameter C. The new concept of selective prediction was discussed in terms of making estimates of the systematic differences in quality of the individual driver data.

Effect of passenger position on fear of danger experienced during sudden bus stops.

Science.gov (United States)

Aoki, Takeo; Uetake, Teruo; Shimoda, Masahiro

2009-06-01

The purpose of this study was to identify the effect of bus passengers' positions on their fear of danger when a bus stopped suddenly. A temporary bus running course with one bus stop was set up on the campus of the Tokyo University of Agriculture and Technology (TUAT). The bus ran the course 14 times with the bus stopping twice during the course, once at the bus stop and again just after re-starting from the bus stop. The driver was asked to brake more strongly than usual when stopping. Sixteen students (15 males and 1 female) between the ages of 18 and 21 years participated. In turn, all participants were asked to take 14 different postures in the bus. Participants were also asked to report their level of fear on a rating scale each time the bus stopped. The study showed that (1) passengers' fear of danger at the first sudden stop was typically higher than that at the second stop, (2) standing passengers who held hand straps experienced more fear than those who held fixed safety devices, (3) bus passengers sitting on the centre of the rear seat had a great risk of injury if the bus stopped suddenly, and (4) when passengers faced the window and stood transversely with respect to from the moving direction of the bus and the bus stopped suddenly, passengers' fear of danger was affected by the side of the bus on which they stood as well as which hand they used to grasp a safety device.

Work Environment, Stress, and Driving Anger: A Structural Equation Model for Predicting Traffic Sanctions of Public Transport Drivers

Science.gov (United States)

2018-01-01

Public transport is an effective and sustainable alternative to private vehicle usage, also helping to reduce the environmental impact of driving. However, the work environment of public transport operators is full of adverse conditions, which, together with their high mileage, may increase the occurrence of negative safety outcomes such as traffic accidents, often preceded by risky road behaviors enhanced by stress, anger, and difficult operating conditions. The aims of this study were, first, to determine the association between work-related psychosocial factors and individual characteristics of public transport drivers and the rate of traffic sanctions they are subject to; and second, to assess the mediation of driving anger in this relationship. A sample of professional drivers (57.4% city bus, 17.6% taxi, and 25% inter-urban bus male operators) was used for this cross-sectional study, responding to a five-section survey including demographic data and driving-related factors, psychosocial work factors including job stress, driving stress, risk predisposition, and driving anger. The results of this study showed significant associations between work-related factors: measures of stress and self-reported rates of traffic fines. Second, it was found that driving anger mediates the associations between driving stress, risk predisposition, and traffic sanctions; and partially mediates the association between driving experience, hourly intensity, and job stress. This study supports the idea that traffic penalties reported by public transport rates are preceded by work-related, personality, and other individual factors that, when combined with driving anger, enhance the occurrence of road misbehavior that may affect overall road safety. PMID:29534530

Work Environment, Stress, and Driving Anger: A Structural Equation Model for Predicting Traffic Sanctions of Public Transport Drivers

Directory of Open Access Journals (Sweden)

Luis Montoro

2018-03-01

Full Text Available Public transport is an effective and sustainable alternative to private vehicle usage, also helping to reduce the environmental impact of driving. However, the work environment of public transport operators is full of adverse conditions, which, together with their high mileage, may increase the occurrence of negative safety outcomes such as traffic accidents, often preceded by risky road behaviors enhanced by stress, anger, and difficult operating conditions. The aims of this study were, first, to determine the association between work-related psychosocial factors and individual characteristics of public transport drivers and the rate of traffic sanctions they are subject to; and second, to assess the mediation of driving anger in this relationship. A sample of professional drivers (57.4% city bus, 17.6% taxi, and 25% inter-urban bus male operators was used for this cross-sectional study, responding to a five-section survey including demographic data and driving-related factors, psychosocial work factors including job stress, driving stress, risk predisposition, and driving anger. The results of this study showed significant associations between work-related factors: measures of stress and self-reported rates of traffic fines. Second, it was found that driving anger mediates the associations between driving stress, risk predisposition, and traffic sanctions; and partially mediates the association between driving experience, hourly intensity, and job stress. This study supports the idea that traffic penalties reported by public transport rates are preceded by work-related, personality, and other individual factors that, when combined with driving anger, enhance the occurrence of road misbehavior that may affect overall road safety.

Work Environment, Stress, and Driving Anger: A Structural Equation Model for Predicting Traffic Sanctions of Public Transport Drivers.

Science.gov (United States)

Montoro, Luis; Useche, Sergio; Alonso, Francisco; Cendales, Boris

2018-03-12

Public transport is an effective and sustainable alternative to private vehicle usage, also helping to reduce the environmental impact of driving. However, the work environment of public transport operators is full of adverse conditions, which, together with their high mileage, may increase the occurrence of negative safety outcomes such as traffic accidents, often preceded by risky road behaviors enhanced by stress, anger, and difficult operating conditions. The aims of this study were, first, to determine the association between work-related psychosocial factors and individual characteristics of public transport drivers and the rate of traffic sanctions they are subject to; and second, to assess the mediation of driving anger in this relationship. A sample of professional drivers (57.4% city bus, 17.6% taxi, and 25% inter-urban bus male operators) was used for this cross-sectional study, responding to a five-section survey including demographic data and driving-related factors, psychosocial work factors including job stress, driving stress, risk predisposition, and driving anger. The results of this study showed significant associations between work-related factors: measures of stress and self-reported rates of traffic fines. Second, it was found that driving anger mediates the associations between driving stress, risk predisposition, and traffic sanctions; and partially mediates the association between driving experience, hourly intensity, and job stress. This study supports the idea that traffic penalties reported by public transport rates are preceded by work-related, personality, and other individual factors that, when combined with driving anger, enhance the occurrence of road misbehavior that may affect overall road safety.

Analysis of a gas turbine driven hybrid drive system for heavy vehicles

Energy Technology Data Exchange (ETDEWEB)

Malmquist, Anders

1999-07-01

The goal of this thesis has been to analyze the performance and behavior of a gas turbine driven hybrid drive train. The thesis covers both computer simulations and experimental tests. In two case studies, a number of measurements have been made on gas turbine driven hybrid vehicles that are developed by Volvo and ABB. In the recent years, much effort is currently put into the design and analysis of hybrid drive trains. Many studies involve computer simulations, but they are often made on a general level. This thesis concentrate on gas turbine driven hybrids for heavy vehicles, a field that has previously not been covered to a large extent in academic studies. A major contribution to the field of hybrid drive train design is the development of detailed simulation models that have a close connection to hybrids that are actually built and tested. The access to detailed gas turbine data has further enhanced the possibility to design a dynamic model of the gas turbine driven and the electric circuits. The combination of simulations and extensive field experience gains new knowledge on the properties of gas turbines in hybrid drive trains. Two simulation models have been developed in Matlab and Simulink. One is a quasi-steady state model that can be used for drive cycle simulations, e.g. a complete bus line. The other is a transient model that combines the thermodynamic properties of the gas turbine, the mechanical properties of the combined turbine-generator shaft, the electric power circuit and the control system. The transient model has been used to simulate the power response during accelerations and retardation. An analysis of the internal energy flows and the system efficiency of a hybrid drive train contributes to the understanding of the properties of series hybrid drive trains. An important part of the topology is that the system is based on a DC/DC-converter that is connected between the battery and the DC-bus. It controls the DC-bus voltage and by this

An Optimization Model for the Selection of Bus-Only Lanes in a City.

Science.gov (United States)

Chen, Qun

2015-01-01

The planning of urban bus-only lane networks is an important measure to improve bus service and bus priority. To determine the effective arrangement of bus-only lanes, a bi-level programming model for urban bus lane layout is developed in this study that considers accessibility and budget constraints. The goal of the upper-level model is to minimize the total travel time, and the lower-level model is a capacity-constrained traffic assignment model that describes the passenger flow assignment on bus lines, in which the priority sequence of the transfer times is reflected in the passengers' route-choice behaviors. Using the proposed bi-level programming model, optimal bus lines are selected from a set of candidate bus lines; thus, the corresponding bus lane network on which the selected bus lines run is determined. The solution method using a genetic algorithm in the bi-level programming model is developed, and two numerical examples are investigated to demonstrate the efficacy of the proposed model.

An Optimization Model for the Selection of Bus-Only Lanes in a City.

Directory of Open Access Journals (Sweden)

Qun Chen

Full Text Available The planning of urban bus-only lane networks is an important measure to improve bus service and bus priority. To determine the effective arrangement of bus-only lanes, a bi-level programming model for urban bus lane layout is developed in this study that considers accessibility and budget constraints. The goal of the upper-level model is to minimize the total travel time, and the lower-level model is a capacity-constrained traffic assignment model that describes the passenger flow assignment on bus lines, in which the priority sequence of the transfer times is reflected in the passengers' route-choice behaviors. Using the proposed bi-level programming model, optimal bus lines are selected from a set of candidate bus lines; thus, the corresponding bus lane network on which the selected bus lines run is determined. The solution method using a genetic algorithm in the bi-level programming model is developed, and two numerical examples are investigated to demonstrate the efficacy of the proposed model.

Understanding Factors of Distraction among Intrastate Bus Driver

Directory of Open Access Journals (Sweden)

Yunos Muhammad Nur Annuar Mohd

2017-01-01

Full Text Available The increase in number of the world population have affected the demand for public transport especially in larger cities. Intrastate buses are chosen as the main public transport by many people due to its affordable fares. Therefore, a better performance of the intrastate bus drivers would be significant to cater the high demand. Nevertheless, distraction among the intrastate bus drivers have been found as one of the major factors that could affect the performance of the drivers. Therefore, the objective of this paper is to provide a better understanding on the factors of distraction among intrastate bus drivers. This paper refers to findings from previous researches which are related to this field of study. In conclusion, this paper will provide a list of factors of distraction among the intrastate bus drivers which may degrade their performance.

NOC AND BUS ARCHITECTURE: A COMPARISON

OpenAIRE

RAJEEV KAMAL; NEERAJ YADAV

2012-01-01

Network-on-chip designs promise to offer considerable advantages over the traditional bus-based architecture. As continuing scaling of Moore’s law enables ever greater transistor densities, design complexity, power limitations and application convergence networks have started to replace busses in much smaller systems and the enhancement of NoC. This paper summarizes the advantages of the NoC and the limitations of traditional bus based architecture. In this paper we discuss a detailed compari...

Writing on the Bus: Using Athletic Team Notebooks and Journals to Advance Learning and Performance in Sports

Science.gov (United States)

Kent, Richard

2012-01-01

"Writing on the Bus" showcases the what, how, and why of using athletic team notebooks and journals. The book guides coaches and athletes, from elementary school through college, in analyzing games while thinking deeply about motivation, goal setting, and communication in order to optimize performance. Filled with lesson plans, writing activities,…

Problems of One School Board Attorney.

Science.gov (United States)

Fisher, M. Bryon

The speaker, a school board attorney, outlines four legal problems he has had to deal with. The cases concern teacher dismissal, the district's responsibility in the case of "hazardous transportation," school district purchases for student activities (student photographs), and school bus leasing. (IRT)

An Experimental Platform for Autonomous Bus Development

Directory of Open Access Journals (Sweden)

Héctor Montes

2017-11-01

Full Text Available Nowadays, with highly developed instrumentation, sensing and actuation technologies, it is possible to foresee an important advance in the field of autonomous and/or semi-autonomous transportation systems. Intelligent Transport Systems (ITS have been subjected to very active research for many years, and Bus Rapid Transit (BRT is one area of major interest. Among the most promising transport infrastructures, the articulated bus is an interesting, low cost, high occupancy capacity and friendly option. In this paper, an experimental platform for research on the automatic control of an articulated bus is presented. The aim of the platform is to allow full experimentation in real conditions for testing technological developments and control algorithms. The experimental platform consists of a mobile component (a commercial articulated bus fully instrumented and a ground test area composed of asphalt roads inside the Consejo Superior de Investigaciones Científicas (CSIC premises. This paper focuses also on the development of a human machine interface to ease progress in control system evaluation. Some experimental results are presented in order to show the potential of the proposed platform.

Optimizing Performance of at-grade Intersection with Bus Rapid Transit Corridor and Heterogeneous Traffic

Directory of Open Access Journals (Sweden)

Hemant Kumar Sharma

2012-06-01

Full Text Available Bus Rapid Transit (BRT has emerged as a preferred mode of public transport in various countries all over the world for its cost effectiveness in construction as well as in operation and maintenance. The rapid transit feature of BRT is seen as a solution to many traffic problems in these countries. However, in developing countries like India, the right -of-way for most of the roads is restricted and traffic is heterogeneous in nature. Provision of BRT in existing right -of-way reduces the capacity available for other motorized traffic. As the buses travel with a certain frequency on dedicated bus- ways, the dedicated corridor remains unused for most of the period when other traffic on motorized vehicle (MV lanes suffers from congestion. The problem gets severe at intersections. However, if buses are operated in mixed traffic it is no more rapid transit. Hence, a solution is required to address this problem and optimize the performance of traffic as a whole. This paper presents the effect if dedicated bus-ways end at a reasonable distance before the stop line at a busy signalized at-grade intersection, and bus lanes (beyond that are made available to all the motorized vehicular traffic (heterogeneous traffic at intersection. The performance evaluation is done in terms of average queue length, maximum queue length, average delay time per vehicle, vehicle throughput, average speed in network and emission of Carbon monoxide CO, mono-nitrogen oxides NOx and Volatile organic compounds (VOC. It is observed that availability of bus lanes to other motorized traffic for a reasonable distance before intersection considerably reduces the average queue length, maximum queue length, average delay time per vehicle and emission per vehicle, while there is an increase in vehicle throughput and average speed of all the vehicles in the network. Thus it results in reduction of congestion and performance enhancement of at-grade intersections and network. Results of

Potential Influence of Metro on Bus: A Case Study

Science.gov (United States)

Selvakumar, M.; Abishek Reddy, M.; Sathish, V.; Venkatesh, R.

2018-06-01

A modal shift occurs when one mode of transport has a comparative advantage in a similar market over another. The present work concerns with the development of modal shift model for urban travel in Chennai, India. The modal shift model was calibrated using binary logit technique and validated using hold-out sample method. The validated model was used to predict the probability of shift in selected corridor. The recent introduction of metro rail in Chennai has lead to an increasing competition among public transport modes. To study the influence of metro on bus transport, a Stated Preference (SP) survey was conducted among express bus travellers. Using the SP survey data, a modal shift model was calibrated to estimate the plausible shift from bus to metro. Results indicate that variables like fare- difference, age, and income play an important role in the shift behaviour. When metro fare increases with respect to express bus fare, bus passengers are less willing to use metro and vice-versa.

Potential Influence of Metro on Bus: A Case Study

Science.gov (United States)

Selvakumar, M.; Abishek Reddy, M.; Sathish, V.; Venkatesh, R.

2018-03-01

A modal shift occurs when one mode of transport has a comparative advantage in a similar market over another. The present work concerns with the development of modal shift model for urban travel in Chennai, India. The modal shift model was calibrated using binary logit technique and validated using hold-out sample method. The validated model was used to predict the probability of shift in selected corridor. The recent introduction of metro rail in Chennai has lead to an increasing competition among public transport modes. To study the influence of metro on bus transport, a Stated Preference (SP) survey was conducted among express bus travellers. Using the SP survey data, a modal shift model was calibrated to estimate the plausible shift from bus to metro. Results indicate that variables like fare-difference, age, and income play an important role in the shift behaviour. When metro fare increases with respect to express bus fare, bus passengers are less willing to use metro and vice-versa.

First aid training in driving schools - uselessness or relevant measure with considerable potential?

Directory of Open Access Journals (Sweden)

Petr Zámečník

2014-12-01

Full Text Available Despite various traffic safety measures traffic accidents still happen. In the Czech Republic, 57 serious accidents happen every day. In situation of accident, immediate help of the bystanders can save lives and reduce damage. Providers of the first aid can also significantly shorten the time before the professional medical assistance arrives by performing the correct procedure of calling emergency line. Czech Red Cross estimates that approximately 10% of the traffic accidents victims should be saved if the bystanders were more able or willing to give them a first aid. In the Czech Republic the system of dispatcher-assisted resuscitation is very well elaborated. After calling the emergency numbers operators are ready to provide the help and advice. Therefore there are no high requirements to the medical knowledge of the first aid providers. That is why the mandatory first aid courses in driving school are only four hours long, what is from expert point of view very unsufficient. Therefore aim of this research was to carry out screening study of effectiveness of the first aid courses in driving schools. In frame of this study was done questionnaire survey among trainees in driving schools focused on willingness and ability to provide first aid and subjective evaluation of these competences. We used adapted Adelborg's first aid questionnaire (Sp?rgeskema om f?rdselsrelateret f?rstehj?lp og genoplivning. The questionnaire was consisted of four parts. The first part affects the socio-demographic data, the second part affects the subjective evaluation of their own competencies, the third part focuses on the evaluation of the course itself and the fourth part takes the form of a test of actual knowledge of first aid. In the fourth part were respondents asked four most important questions in line with the European Resuscitation Council Guidelines for Resuscitation and with International first aid and resuscitation guidelines of International Federation

Bosch automotive electrics and automotive electronics systems and components, networking and hybrid drive

CERN Document Server

2014-01-01

The significance of electrical and electronic systems has increased considerably in the last few years and this trend is set to continue. The characteristics feature of innovative systems is the fact that they can work together in a network. This requires powerful bus systems that the electronic control units can use to exchange information. Networking and the various bus systems used in motor vehicles are the prominent new topic in the 5th edition of the "Automotive Electric, Automotive Electronics" technical manual. The existing chapters have also been updated, so that this new edition brings the reader up to date on the subjects of electrical and electronic systems in the motor vehicle. Content Electrical and electronical systems – Basic principles of networking - Examples of networked vehicles – Bus systems – Architecture of electronic systems – Mechatronics – Elektronics – Electronic control Units – Software – Sensors – Actuators – Hybrid drives – Vehicle electrical system – Start...

SmartDriver for school bus : participant's handbook

International Nuclear Information System (INIS)

2007-01-01

SmartDriver is a key component of Natural Resources Canada's ecoENERGY for fleets program. The aim of the ecoENERGY initiative is to introduce fleets to energy-efficient practices for reducing fuel consumption and emissions and to help drivers adopt the driving practices outlined in the SmartDriver training materials. The handbook was designed as part of a comprehensive media package that included a CD-ROM with audio-visual components. The package was developed as a training strategy for fuel-efficient driving skills. The first module contained information on air pollution and techniques that drivers can adopt to reduce particulate matter, smog, greenhouse gas (GHG) emissions. An outline of new engine technologies developed to reduce emissions was also provided. The second module discussed various vehicle factors that influence fuel efficiency. Alternative fuels were reviewed, and vehicle components were discussed in relation to improving fuel economy. The module also included preventive maintenance tips as well as engine starting techniques and methods for reducing time spent idling. Various activities and games related to improving fuel efficiency were also included. 17 figs

Schedule and complex motion of shuttle bus induced by periodic inflow of passengers

Science.gov (United States)

Nagatani, Takashi; Naito, Yuichi

2011-09-01

We have studied the dynamic behavior of a bus in the shuttle bus transportation with a periodic inflow. A bus schedule is closely related to the dynamics. We present the modified circle map model for the dynamics of the shuttle bus. The motion of the shuttle bus depends on the loading parameter and the inflow period. The shuttle bus displays the periodic, quasi-periodic, and chaotic motions with varying both loading parameter and inflow rate.

Predicting active school travel: The role of planned behavior and habit strength

Science.gov (United States)

2012-01-01

Background Despite strong support for predictive validity of the theory of planned behavior (TPB) substantial variance in both intention and behavior is unaccounted for by the model’s predictors. The present study tested the extent to which habit strength augments the predictive validity of the TPB in relation to a currently under-researched behavior that has important health implications, namely children’s active school travel. Method Participants (N = 126 children aged 8–9 years; 59 % males) were sampled from five elementary schools in the west of Scotland and completed questionnaire measures of all TPB constructs in relation to walking to school and both walking and car/bus use habit. Over the subsequent week, commuting steps on school journeys were measured objectively using an accelerometer. Hierarchical multiple regressions were used to test the predictive utility of the TPB and habit strength in relation to both intention and subsequent behavior. Results The TPB accounted for 41 % and 10 % of the variance in intention and objectively measured behavior, respectively. Together, walking habit and car/bus habit significantly increased the proportion of explained variance in both intention and behavior by 6 %. Perceived behavioral control and both walking and car/bus habit independently predicted intention. Intention and car/bus habit independently predicted behavior. Conclusions The TPB significantly predicts children’s active school travel. However, habit strength augments the predictive validity of the model. The results indicate that school travel is controlled by both intentional and habitual processes. In practice, interventions could usefully decrease the habitual use of motorized transport for travel to school and increase children’s intention to walk (via increases in perceived behavioral control and walking habit, and decreases in car/bus habit). Further research is needed to identify effective strategies for changing these

Evaluation of Urban Bus Transport Failure in Gujranwala City of Pakistan

OpenAIRE

MUHAMMAD WAQAR ASLAM; ZAHARA BATOOL

2017-01-01

This research work has evaluated the performance of urban public bus transport service operating in Gujranwala city of Pakistan. The assessment has been made in terms of financial viability, bus condition, operational performance and user perception. Based on the data requirements, various traffic/transport surveys were conducted including Passenger Boarding and Alighting Survey, Bus Count Survey, Bus Inspection Survey, Illegal Operations Survey and Public Transport User Interview Survey in c...

ANALISIS SARANA ANGKUTAN UMUM BUS DAMRI DI KOTA SEMARANG

Directory of Open Access Journals (Sweden)

Subhan Rizal Amin

2015-12-01

Full Text Available This study aims to analyze the availability and use of public transportation by taking a case study of the Damri bus which has Ngaliyan-Pucanggading route. The availability of public transport is not comparable to the demand for public transportation services so that the problems of transportation emerge. Additionally, the use of public transport becomes an important factor to develop the transportation. The study is conducted by surveying the Damri passengers of B.04 lane and logistic regression is used for the analysis. The method of determining the needs of transportation is issued by Departemen Perhubungan. It is used to calculate and determine whether the public transportation should be added or reduced. Then, the factors used as the independent variables in the analysis are the Damri’s safety, effectiveness, efficiency, service and reliability. The results show that Perum Damri does not need to add more Damri bus for B.04 because the results’ calculation is 0.6. and the factors that significantly influence the use Damri bus is the variable of safety, effectiveness and efficiency. However, the variables of service and reliability do not significantly influence the use of B.04 Damri bus.Penelitian ini bertujuan untuk menganalisis ketersediaan dan penggunaan angkutan sarana angkutan umum penumpang dengan mengambil studi kasus pada bus Damri jalur dengan trayek Ngaliyan-Pucanggading. Ketersediaan sarana angkutan umum yang tersedia tidak sebanding dengan besarnya permintaan akan jasa angkutan umum oleh masyarakat umum sehingga muncul permasalahan transportasi. Di samping itu, penggunaan angkutan umum yang beroperasi menjadi faktor penting dalam upaya pengembangan sarana transportasi. Penelitian ini dilakukan dengan menggunakan metode survey terhadap para penumpang bus Damri jalur B.04 dan dianalisis dengan Regresi Logistik. Metode penentuan kebutuhan armada dikeluarkan oleh Departemen Perhubungan yang digunakan untuk menghitung apakah suatu

Bus basics

International Nuclear Information System (INIS)

Dobinson, R.W.

1983-01-01

The aims of this course are: 1. To introduce the general concepts of buses used to interconnect processors, perpherals, and instrumentation. 2. To classify, albeit crudely, different types of bus systems. 3. To give some examples of past, present, and future buses as applied to the field of high-energy physics, including some details of software. 4. To provide references for further study. (orig.)

Research on the Coordinated Design of Bus and Taxi Station

Directory of Open Access Journals (Sweden)

Jiangfeng Xi

2015-01-01

Full Text Available Rises in the number of transit buses, bus routes, and overall traffic volume in China’s cities, coupled with interference from other transport modes, such as taxis loading and unloading passengers nearby, have led to increasing traffic delays at bus stops, which is considered one of the factors degrading service levels and traffic operations on urban roadways. This paper studies traffic characteristics at bus stops, investigates variations in delay from different types or designs of bus stops, and analyzes the impact of it on traffic capacity, the purpose of which is to propose a solution to predicting the feasibility of an integrated design of bus stops and taxi stands with the help of mathematical models and based on the objectives of optimal traffic operations and passenger transfer.

Bus line classification using neural networks

OpenAIRE

Jiménez Alonso, Felipe; Serradilla García, Francisco; Román de Andrés, Alfonso; Naranjo Hernandez, Jose Eugenio

2014-01-01

Grouping urban bus routes is necessary when there are evidences of significant differences among them. In Jiménez et al. (2013), a reduced sample of routes was grouped into clusters utilizing kinematic measured data. As a further step, in this paper, the remaining urban bus routes of a city, for which no kinematic measurements are available, are classified. For such purpose we use macroscopic geographical and functional variables to describe each route, while the clustering process is perform...

VICbus: A standard inter-crate bus

International Nuclear Information System (INIS)

Parkman, C.F.

1990-01-01

VICbus is a standard inter-crate cable bus being developed by a working group of the ISO/IEC. Derived from an initiative of the VMEbus Working Group of ESONE, VICbus aims to provide users of multi-crate VMEbus and other backplane bus systems with a standard inter-crate connection. Multi-drop operation is provided for up to 31 devices on a cable of maximum 100 metres in length. Two data transfer protocols are specified, compelled (asynchronous) transfers for transparent interconnection of backplane bus systems (VMEbus in the first instance), and high-speed, non-compelled (synchronous) transfers between VICbus interfaces. A limited interrupt mechanism is specified, as well as simple, but efficient arbitration technique. Conventional technology is employed: copper cables, existing transcievers, and differential signal transmission, together with proven low-level protocols. Data transfer rates in excess of 30 Mbyte/s will be possible on a cable length of 30 metres

Speed Regulated Continuous DTC Induction Motor Drive in Field Weakening

Directory of Open Access Journals (Sweden)

MATIC, P.

2011-02-01

Full Text Available The paper describes sensorless speed controlled continuous Direct Torque Control (DTC Induction Motor (IM drive in the field weakening regime. Drive comprises an inner torque loop and an outer speed loop. Torque control is based on Proportional - Integral (PI controller with adaptive Gain Scheduling (GS parameters. The GS PI control provides full DC link voltage utilization and a robust disturbance rejection along with a fast torque response. Outer speed loop has a PI regulator with the gains selected so as to obtain a fast and strictly aperiodic response. Proposed drive fully utilizes the available DC bus voltage. The paper comprises analytical considerations, simulation results, and detailed description of the implementation steps. Experimental verification of the proposed solution is conducted on a fixed point Digital Signal Processor (DSP platform.

Digital processing data communication systems (bus systems)

International Nuclear Information System (INIS)

Fleck, K.

1980-01-01

After an introduction to the technology of digital processing data communication systems there are the following chapters: digital communication of processing data in automation technology, the technology of biserial communication, the implementaiton of a bus system, the data transmission of the TDC-2000 system of Honeywell's and the process bus CS 275 in the automation system TELEPERM M of Siemens AG. (WB) [de

Impact of work-related and psychosocial factors on the development of ischemic heart disease among urban bus drivers in Denmark

DEFF Research Database (Denmark)

Netterstrøm, Bo; Juel, K

1988-01-01

From 1978 to 1985, 2,465 male bus drivers in the three major cities in Denmark were followed with regard to hospital admission due to myocardial infarction (MI) and death due to ischemic heart disease (IHD). In all 2,045 (83%) of these men responded in 1978 to a questionnaire on psychosocial well...... associated with the occurrence of MI. Smoking habits tended to be associated with the occurrence of MI, while stress symptoms and job dissatisfaction did not. The mental burden on bus drivers working in heavy traffic seems a possible explanation for the findings.......-being and work conditions. The respondents did not differ from the nonrespondents regarding hospital admissions and death in the follow-up period (1978-1984). Sixty-two cases of MI were registered among the 2,045 bus drivers in 1978-1984. On this basis relative risk for MI was calculated with a multiple...... regression model for independent variables regarding psychosocial well-being and work conditions. High work load (driving in heavy traffic) was significantly associated with the occurrence of MI. Of the psychosocial factors "no social contact with colleagues" and "increased work pace" were also significantly...

Wisdom and Bus Schedules: Developing School Leadership

Science.gov (United States)

Glatter, Ron

2009-01-01

This article is based on a synthesis study of school leadership development conducted for the National College of School Leadership (NCSL) in England. It first outlines a perspective on leadership focusing on the concepts of wisdom, deliberation and higher order capacities. Then it describes and assesses two distinct models of leadership learning,…

Truck Driving Schools

Data.gov (United States)

Department of Homeland Security — his dataset is composed of any type of Post Secondary Education facility such as: colleges, universities, technical schools, or trade schools that provide training...

Developing a viable electric bus service: the Milton Keynes demonstration project

OpenAIRE

Miles, John; Potter, Stephen

2014-01-01

Buses can be a serious source of city centre air pollution. Electric buses deliver zero emissions but, because of the time required to recharge, more buses are needed for a given timetable than diesel counterparts, so making mainstream electric bus operations prohibitively expensive.\\ud \\ud Early 2014 saw the implementation in Milton Keynes of an electric bus service designed to overcome this problem. An entire bus route has been converted to electric operation with inductive charging at bus ...

SOLVING OF SCHOOL BUS ROUTING PROBLEM BY ANT COLONY OPTIMIZATION RESOLUCIÓN DEL PROBLEMA DE RUTEO DE BUSES ESCOLARES CON OPTIMIZACIÓN POR COLONIA DE HORMIGAS RESOLUÇÃO DO PROBLEMA DE RUTEO DE ÔNIBUS ESCOLARES COM OTIMIZAÇÃO POR COLÔNIA DE FORMIGAS

Directory of Open Access Journals (Sweden)

Juan S Arias-Rojas

2012-06-01

Full Text Available The school bus routing problem (SBRP seeks to plan an efficient schedule of a fleet of school buses that must pick up students from various bus stops and deliver them by satisfying various constraints: maximum capacity of the bus, maximum riding time of students, time window to arrive to school. In this paper, we consider a case study of SBRP for a school in Bogotá, Colombia. The problem is solved using ant colony optimization (ACO. Computational experiments are performed using real data. Results lead to increased bus utilization and reduction in transportation times with on-time delivery to the school. The proposed decision-aid tool has shown its usefulness for actual decision-making at the school: it outperforms current routing by reducing the total distance traveled by 8.3 % and 21.4 % respectively in the morning and in the afternoon.El problema de ruteo de buses escolares (SBRP busca encontrar el programa más eficiente para una flota de buses escolares que deben recoger y despachar estudiantes en varias paradas de bus satisfaciendo varias restricciones: capacidad máxima del bus, máximo tiempo de recorrido de los estudiantes, ventanas de tiempo para la llegada al colegio. En este artículo se considera un caso de estudio de un problema SBRP para un colegio en Bogotá, Colombia. El problema se resuelve usando la metaheurística de colonia de hormigas (ACO. Los experimentos computacionales se realizan empleando datos reales. Los resultados muestran el incremento en el nivel de utilización de los buses y una reducción en los tiempos de transporte con despacho a tiempo en el colegio. La herramienta ha mostrado su utilidad para la planeación regular de buses en el colegio: se redujo la distancia total recorrida en 8,3 % en la mañana y en 21,4 % en la tarde.O problema de roteamento de ônibus escolares (SBRP busca encontrar o programa mais eficiente para uma frota de ônibus escolares que devem recolher e despachar estudantes em v

Level of Bus Performance Based On the Relationship Between Distance and Travel Time of Universiti Tun Hussein Onn Malaysia (UTHM Bus Services

Directory of Open Access Journals (Sweden)

Prasetijo Joewono

2017-01-01

Full Text Available UTHM bus service is an important transport mode for most students at Universiti Tun Hussein Onn because it such primary public vehicle to support students movements around the campus, within and outside student apartments. This service is often associated with the quality of service in terms of time, stops and comforts. Therefore, this following study is focused on investigation on several UTHM bas routes which was based on bas operations such as distance and travel time/travel distance that would determine the level of service provided. Primary data were collected mainly to obtain information relate to speed, bas position, time movement/circulations of bus and time headway. These were obtained by installing GPS-Slute Gear i-trail along bus travels. In addition, additional data were collected by exploring previous studies regarding to the bus services such as Highway Capacity Manual (HCM 2010. The approach used was based on assessment of progress used to determine the level of quest service and such obstacle frequently occurs with results on bus delays, volume of unequal that can be overcome according to the assessments that have been provided.

Network Analysis of Urban Traffic with Big Bus Data

OpenAIRE

Zhao, Kai

2016-01-01

Urban traffic analysis is crucial for traffic forecasting systems, urban planning and, more recently, various mobile and network applications. In this paper, we analyse urban traffic with network and statistical methods. Our analysis is based on one big bus dataset containing 45 million bus arrival samples in Helsinki. We mainly address following questions: 1. How can we identify the areas that cause most of the traffic in the city? 2. Why there is a urban traffic? Is bus traffic a key cause ...

Kajian Keamanan Pengoperasian Public Transport Tinjauan Terhadap Kekuatan Rangka Body Bus

OpenAIRE

Sudiro, B. M

2010-01-01

In order to meet the safety and security of the public transportation, design specification of construction body bus or bus frame structures should have an appropriate structural strength and comply with standard design including the safety factor and selection of material besides static and dynamic testing of the part of body bus. It is also realized that a bus carrying passengers have to give secure to the passengers also driver.The fact that a technology concerning with metal works indus...

Modelling Field Bus Communications in Mixed-Signal Embedded Systems

Directory of Open Access Journals (Sweden)

Alassir Mohamad

2008-01-01

Full Text Available Abstract We present a modelling platform using the SystemC-AMS language to simulate field bus communications for embedded systems. Our platform includes the model of an I/O controller IP (in this specific case an C controller that interfaces a master microprocessor with its peripherals on the field bus. Our platform shows the execution of the embedded software and its analog response on the lines of the bus. Moreover, it also takes into account the influence of the circuits's I/O by including their IBIS models in the SystemC-AMS description, as well as the bus lines imperfections. Finally, we present simulation results to validate our platform and measure the overhead introduced by SystemC-AMS over a pure digital SystemC simulation.

Modelling Field Bus Communications in Mixed-Signal Embedded Systems

Directory of Open Access Journals (Sweden)

Patrick Garda

2008-08-01

Full Text Available We present a modelling platform using the SystemC-AMS language to simulate field bus communications for embedded systems. Our platform includes the model of an I/O controller IP (in this specific case an I2C controller that interfaces a master microprocessor with its peripherals on the field bus. Our platform shows the execution of the embedded software and its analog response on the lines of the bus. Moreover, it also takes into account the influence of the circuits's I/O by including their IBIS models in the SystemC-AMS description, as well as the bus lines imperfections. Finally, we present simulation results to validate our platform and measure the overhead introduced by SystemC-AMS over a pure digital SystemC simulation.

STRATEGI PENGEMBANGAN TRANSPORTASI WISATA KURA-KURA BUS DI BALI

Directory of Open Access Journals (Sweden)

Ayu Kusuma

2018-01-01

Full Text Available Kura-Kura Bus is one of tourist transportation companies in Bali with public shuttle bus service in tourism route. Data analysis in this research were using SWOT and AHP analysis, with participants who have position minimal as a supervisor. Participants selected based on their expertise and relevance with this article. Based on the results of SWOT and AHP analysis to develop tourist transportation is Kura-Kura Bus, which is considered the most realistic scenario is an optimistic scenario, with the goal to be a safe and comfortable transportation. To achieve the goal, based on priority strategies that could be done by management of Kura-Kura Bus are developing unique products, finding new markets, favoring public transport services, enchance brand reputation, developing smartphone application, and cross promotion with supplier.

Bitmap-Wise Wireless M-Bus Coordination for Sustainable Real Time Energy Management

Directory of Open Access Journals (Sweden)

Kwang-il Hwang

2014-07-01

Full Text Available Even though WM-Bus is being considered to be the most promising network protocol for smart metering, it is not suitable for a sustainable real-time home energy management system (HEMS, which requires higher reliability and longer lifetime despite real time bi-directional communications. Therefore, in this paper we propose a Bitmap-wise WM-Bus (BWM-Bus, coping well with sustainable real-time HEMS. In particular, the proposed scheme addresses the several problems in WM-Bus for HEMS by introducing novel functions: asynchronous meter trigger, adaptive slot scheduling, and bitmap-wise retransmission request. Through experiments, we demonstrate that BWM-Bus guarantees higher data success ratio with lower data aggregation time, as well as longer lifetime than WM-Bus standard.

3D reconstructions of a controlled bus bombing

DEFF Research Database (Denmark)

Villa, Chiara; Hansen, Nikolaj Friis; Hansen, Kamilla Maria

2018-01-01

Objectives: to demonstrate the usefulness of 3D reconstructions to better understand the dynamic of a controlled bus bombing. Materials and methods: 3D models of the victims (pigs) were created from post-mortem CT scanning using Mimic software; 3D models of the crime scene (bus) were generated by...

Bus Operation Monitoring Oriented Public Transit Travel Index System and Calculation Models

Directory of Open Access Journals (Sweden)

Jiancheng Weng

2013-01-01

Full Text Available This study proposed a two-dimensional index system which is concerned essentially with urban travel based on travel modes and user satisfaction. First, the public transit was taken as an example to describe the index system establishing process. In consideration of convenience, rapid, reliability, comfort, and safety, a bus service evaluation index system was established. The indicators include the N-minute coverage of bus stops, average travel speed, and fluctuation of travel time between stops and bus load factor which could intuitively describe the characteristics of public transport selected to calculate bus travel indexes. Then, combined with the basic indicators, the calculation models of Convenience Index (CI, Rapid Index (RI, Reliability Index (RBI, and Comfort Index (CTI were established based on the multisource data of public transit including the real-time bus GPS data and passenger IC card data. Finally, a case study of Beijing bus operation evaluation and analysis was conducted by taking real bus operation data including GPS data and passenger transaction recorder (IC card data. The results showed that the operation condition of the public transit was well reflected and scientifically classified by the bus travel index models.

ARCNET as a field bus in the Fermilab linac control system

International Nuclear Information System (INIS)

Shea, M.F.; Goodwin, R.W.; Kucera, M.J.; Shtirbu, S.

1992-01-01

Data acquisition hardware in accelerator control systems is connected by a field bus to networked computers that supply data to consoles. Industry attempts to standardize on a low level field bus have not succeeded in providing a single well-supported bus. This paper describes a data acquisition chassis that connects to VMEbus computers using ARCNET, a full featured token-passing local area network, as the field bus. The performance of this technique as implemented in the control system for the Fermilab Linac is given. (author)

Idle reduction programs and potential benefits to schools

Science.gov (United States)

2010-11-01

School districts in Texas and many other states have, in recent years, increased the walk zones : surrounding schools to a 2-mile perimeter. Inside this perimeter, either no school bus service is : offered, or service is offered only with a fee...

Learning NServiceBus

CERN Document Server

Boike, David

2013-01-01

This is a practical tutorial containing hands-on examples for creating a messaging and SOA based service bus.This book is for .NET developers who are looking for ways to overcome problems related to buggy third party web service integrations, codebases that have grown into a big ball of mud, and batch jobs failure.

Sustainable transport and the organisation of bus services in Manchester

DEFF Research Database (Denmark)

Gudmundsson, Henrik; Sørensen, Claus Hedegaard

2008-01-01

alternative modes of transport to private cars, such as public transport. In this paper we focus only on the potential of bus transport services in cities for attracting travellers from cars. It is a basic assumption behind this paper that the ability of public bus transport to attract travellers from cars...... depends on how the bus sector is organised. By organisation we adopt an institutional point of view and consider basic modes of governance. Basic modes of governance include the forms “market”, “hierarchy” and “network” (Powell 1990). So-called New Public Management (NPM) reforms have changed the modes...... of governance of bus transport in several countries, including Denmark and the United Kingdom. Our focus is on how New Public Mangement Reforms have changed the mix of governance modes and thus may have influenced the ability of urban bus transport to attract travellers from cars. We focus on a particular case...

Black silicon solar cells with black bus-bar strings

DEFF Research Database (Denmark)

Davidsen, Rasmus Schmidt; Tang, Peter Torben; Mizushima, Io

2016-01-01

We present the combination of black silicon texturing and blackened bus-bar strings as a potential method for obtaining all-black solar panels, while using conventional, front-contacted solar cells. Black silicon was realized by maskless reactive ion etching resulting in total, average reflectance...... below 0.5% across a 156x156 mm2 silicon wafer. Four different methods to obtain blackened bus-bar strings were compared with respect to reflectance, and two of these methods (i.e., oxidized copper and etched solder) were used to fabricate functional allblack solar 9-cell panels. The black bus-bars (e.......g., by oxidized copper) have a reflectance below 3% in the entire visible wavelength range. The combination of black silicon cells and blackened bus-bars results in aesthetic, all-black panels based on conventional, front-contacted solar cells without compromising efficiency....

Small Explorer Data System MIL-STD-1773 fiber optic bus

Science.gov (United States)

Flanegan, Mark; Label, Ken

1992-01-01

The MIL-STD-1773 Fiber Optic Data Bus as implemented in the GSFC Small Explorer Data System (SEDS) for the Small Explorer Program is described. It provides an overview of the SEDS MIL-STD-1773 bus components system design considerations, reliability figures, acceptance and qualification testing requirements, radiation requirements and tests, error handling considerations, and component heritage. The first mission using the bus will be launched in June of 1992.

Leading Schools through Major Change

Science.gov (United States)

Syed, Sarosh

2013-01-01

Changing even the smallest things in schools is hard--just ask any principal who has overseen a rescheduling of bus routes. So imagine the difficulty of getting a school to move its curriculum and instruction from familiar learning requirements to brand-new nationwide standards. Yet this is exactly the sort of change public schools in 45 states…

Hierarchical Delay-Dependent Distributed Coordinated Control for DC Ring-Bus Microgrids

DEFF Research Database (Denmark)

Dou, Chunxia; Yue, Dong; Zhang, Zhanqiang

2017-01-01

In this paper, a hierarchical distributed coordinated control method is proposed based on the multi-agent system for dc ring-bus microgrids to improve the bus voltage performance. First, a two-level multi-agent system is built, where each first-level unit control agent is associated with a distri......In this paper, a hierarchical distributed coordinated control method is proposed based on the multi-agent system for dc ring-bus microgrids to improve the bus voltage performance. First, a two-level multi-agent system is built, where each first-level unit control agent is associated...

Swisstrolley 3 - An articulated trolley bus; SWISSTROLLEY 3. Gelenktrolleybus

Energy Technology Data Exchange (ETDEWEB)

Gisler, H.-J.

2006-07-01

This illustrated final report for the Swiss Federal Office of Energy (SFOE) takes a look at the Swisstrolley 3 low-floor, articulated trolley bus developed in Switzerland by the Hess AG company. Various features of the variants of the trolley bus, including single vehicle, single and double-articulated buses and bus trailers, are discussed. The reductions achieved in energy consumption, weight and noise are discussed. Typical values for power consumption are presented in graphical form. Economic viability and passenger-friendliness are examined, as are possibilities for further improvement.

School Climate Improvement Action Guide for Noninstructional Staff. School Climate Improvement Resource Package

Science.gov (United States)

National Center on Safe Supportive Learning Environments, 2017

2017-01-01

Improving school climate takes time and commitment from a variety of people in a variety of roles. This document outlines key action steps that noninstructional staff--including guidance counselors, social workers, school psychologists, office staff, bus drivers, maintenance and facility staff, and food service staff--can take to support school…

A Modular Active Front-End Rectifier with Electronic Phase-Shifting for Harmonic Mitigation in Motor Drive Applications

DEFF Research Database (Denmark)

Zare, Firuz; Davari, Pooya; Blaabjerg, Frede

2017-01-01

In this paper, an electronic phase-shifting strategy has been optimized for a multi-parallel configuration of line-commutated rectifiers with a common dc-bus voltage used in motor drive application. This feature makes the performance of the system independent of the load profile and maximizes its...

Connecticut nutmeg fuel cell bus project : first analysis report.

Science.gov (United States)

2012-07-01

This report summarizes the experience and early results from a fuel cell bus demonstration funded by the Federal Transit Administra-tion (FTA) under the National Fuel Cell Bus Program (NFCBP). A team led by the Northeast Advanced Vehicle Consortium a...

Bus Lifecycle Cost Model for Federal Land Management Agencies.

Science.gov (United States)

2011-09-30

The Bus Lifecycle Cost Model is a spreadsheet-based planning tool that estimates capital, operating, and maintenance costs for various bus types over the full lifecycle of the vehicle. The model is based on a number of operating characteristics, incl...

Science of driving.

Science.gov (United States)

2016-08-01

The Science of Driving project focused on developing a collaborative relationship to develop curriculum units for middle school and high school students to engage them in exciting real-world scenarios. This effort involved faculty, staff, and student...

Superconducting link bus design for the accelerator project for upgrade of LHC

International Nuclear Information System (INIS)

Nobrega, F.; Brandt, J.; Cheban, S.; Feher, S.; Kaducak, M.; Kashikhin, V.; Peterson, T.

2011-01-01

The Accelerator Project for Upgrade of LHC (APUL) is a U.S. project participating in and contributing to CERN's Large Hadron Collider (LHC) upgrade program. Fermi National Accelerator Laboratory in collaboration with Brookhaven National Laboratory was developing sub-systems for the upgrade of the LHC final focus magnet systems. Part of the upgrade called for various lengths of superconducting power transmission lines known as SC Links which were up to 100 m long. The SC Link electrically connects the current leads in the Distribution Feed Boxes to the interaction region magnets. The SC Link is an extension of the magnet bus housed within a cryostat. The present concept for the bus consists of 22 power cables, 4 x 13 kA, 2 x 7 kA, 8 x 2.5 kA and 8 x 0.6 kA bundled into one bus. Different cable and strand possibilities were considered for the bus design including Rutherford cable. The Rutherford cable bus design potentially would have required splices at each sharp elbow in the SC Link. The advantage of the round bus design is that splices are only required at each end of the bus during installation at CERN. The round bus is very flexible and is suitable for pulling through the cryostat. Development of the round bus prototype and of 2 splice designs is described in this paper. Magnetic analysis and mechanical test results of the 13 kA cable and splices are presented.

26 CFR 48.4221-8 - Tax-free sales of tires, tubes, and tread rubber used on intercity, local, and school buses.

Science.gov (United States)

2010-04-01

... if the bus has a passenger seating capacity of at least 20 adults and the transportation is available... of a school. Incidental use (deadheading) of the school bus without passengers to or from a point to... used on intercity, local, and school buses. 48.4221-8 Section 48.4221-8 Internal Revenue INTERNAL...

76 FR 68819 - State of Good Repair Bus and Bus Facilities Discretionary Program Funds

Science.gov (United States)

2011-11-07

... Availability on June 24, 2011. The SGR Initiative makes funds available to public transit providers to finance capital projects to replace, rehabilitate, and purchase buses and related equipment and to construct bus...

EtherBone - A Network Layer for the Wishbone SoC Bus

CERN Document Server

Kreider, M; Lewis, J; Włostowski, T; Serrano, J

2011-01-01

Today, there are several System on a Chip (SoC) bus systems. Typically, these buses are confined on-chip and rely on higher level components to communicate with the outside world. Taking these systems a step further, we see the possibility of extending the reach of the SoC bus to remote FPGAs or processors. This leads to the idea of the EtherBone (EB) core, which connects a Wishbone (WB) Ver. 4 Bus via a Gigabit Ethernet based network link to remote peripheral devices. EB acts as a transparent interconnect module towards attached WB Bus devices. Address information and data from one or more WB bus cycles is preceded with a descriptive header and encapsulated in a UDP/IP packet. Because of this standard compliance, EB is able to traverse Wide Area Networks and is therefore not bound to a geographic location. Due to the low level nature of the WB bus, EB provides a sound basis for remote hardware tools like a JTAG debugger, In-System-Programmer (ISP), boundary scan interface or logic analyser module. EB was de...

School buses, air pollution and children's health: follow-up report

International Nuclear Information System (INIS)

Perrotta, K.

2010-10-01

This document is designed to be a follow-up report to the Ontario Public Health Association (OPHA) school bus report published in 2005, and was produced through a collaboration between the Clean Air Partnership and the OPHA. The level of awareness of school bus emissions are evaluated in this report. The document also provides a review of projects handled by the federal government, programs developed by governments of other provinces and the policies followed by school boards in other provinces, to mitigate emissions and exposures related to school buses. Several recommendations were made, including the replacement of older school buses, adapt the routes considering the emissions generated and promote the use of biodiesel to reduce emissions of air pollutants and greenhouse gases. 36 refs, 8 tabs.

Miniature JPL Universal Instrument Bus

Data.gov (United States)

National Aeronautics and Space Administration — Develop a Universal Digital Processor Bus architecture using state of the art commercial packaging technologies. This work will transition commercial advanced- yet...

Assessing the impacts of deploying a shared self-driving urban mobility system: An agent-based model applied to the city of Lisbon, Portugal

Directory of Open Access Journals (Sweden)

Luis M. Martinez

2017-06-01

Full Text Available This paper examines the changes that might result from the large-scale uptake of a shared and self-driving fleet of vehicles in a mid-sized European city. The work explores two different self-driving vehicle concepts – a ridesharing system (Shared Taxi, which emulates a taxi-like system where customers accept small detours from their original direct path and share part of their ride with others and a dynamic bus-like service with minibuses (Taxi-Bus, where customers pre-book their service at least 30 min in advance (permanent bookings for regular trips should represent most requests and walk short distances to a designated stop. Under the premise that the “upgraded” system should as much as possible deliver the same trips as today in terms of origin, destination and timing, and that it should also replace all car and bus trips, it looks at impacts on car fleet size, volume of travel and parking requirements. Mobility output and CO2 emissions are also detailed in two different time scales (24 h. average and peak-hour only. The obtained results suggest that a full implementation scenario where the existing metro service is kept and private car, bus and taxi mobility would be replaced by shared modes would significantly reduce travelled vehicle.kilometres and CO2 emissions.

Analyzing the Relationship Between Bus Pollution Policies and Morbidity Using a Quasi-Experiment.

Science.gov (United States)

Ngo, Nicole S

2015-09-01

Transit buses are used by millions of commuters every day, but they emit toxic diesel fumes. In 1988, the U.S. Environmental Protection Agency implemented emission standards for transit buses, which have been continually updated. Yet there is no quantitative evidence of the health benefits from these bus pollution policies due to data constraints and confounding variables. In this study, a quasi-experiment is used to exploit the geographic and temporal variation in emission standards by using bus vintage as a proxy for bus emissions. This is accomplished using a unique, rich panel data set, which includes daily information on bus vintage and route for the New York City Transit bus fleet between 2006 and 2009. This information is merged with daily data on emergency department (ED) visits for respiratory illnesses, which include patients' residences at the census block level and exact admission date. Economic benefits resulting from these bus pollution policies are then estimated. Results show that stricter transit bus emission standards by the U.S. Environmental Protection Agency for particulate matter are associated with reduced ED visits for respiratory diseases for patients living within a few hundred feet of a bus route. These findings demonstrate that bus pollution policies have made critical improvements to public health.

Aspek Hukum Perlindungan terhadap Penumpang Bus dalam Mewujudkan Perlindungan Konsumen

OpenAIRE

Harahap, Rabiah Z

2016-01-01

Bus is the one of transportation which is often used by society. Society as passenger of bus righteously gains protection. Many of accident happens in public transportation especially bus that rises a question the important of protection for people as the accicent victim. This question is worthy to be solved because many of public transportation company ignores the passenger's right. Based on this, government shall take control with presentation of new regulation that aims protection people ...

SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Third Results Reports

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Chandler, K.

2012-05-01

This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. NREL has previously published two reports documenting the operation of the fuel cell bus in service. This report provides a summary of the results with a focus on the bus operation from July 2011 through January 2012.

ETHERBONE - a network layer for the wishbone SoC bus

International Nuclear Information System (INIS)

Kreider, M.; Terpstra, W.; Lewis, J.; Serrano, J.; Wlostowski, T.

2012-01-01

Today, there are several System on a Chip (SoC) bus systems. Typically, these buses are confined on-chip and rely on higher level components to communicate with the outside world. Taking these systems a step further, we see the possibility of extending the reach of the SoC bus to remote FPGAs or processors. This leads to the idea of the EtherBone (EB) core, which connects a Wishbone (WB) Ver. 4 Bus via a Gigabit Ethernet based network link to remote peripheral devices. EB acts as a transparent interconnect module towards attached WB Bus devices. Address information and data from one or more WB bus cycles is preceded with a descriptive header and encapsulated in a UDP/IP packet. Because of this standard compliance, EB is able to traverse Wide Area Networks and is therefore not bound to a geographic location. Due to the low level nature of the WB bus, EB provides a sound basis for remote hardware tools like a JTAG debugger, In-System-Programmer (ISP), boundary scan interface or logic analyser module. EB was developed in the scope of the White-Rabbit Timing Project (WR) at CERN and GSI/FAIR, which employs GigaBit Ethernet technology to communicate with memory mapped slave devices. WR will make use of EB as means to issue commands to its timing nodes and control connected accelerator hardware. (authors)

Active Power Filter DC Bus Voltage Piecewise Reaching Law Variable Structure Control

OpenAIRE

Liu, Baolian; Ding, Zujun; Zhao, Huanyu; Jin, Defei

2014-01-01

The DC bus voltage stability control is one key technology to ensure that Active Power Filter (APF) operates stably. The external disturbances such as power grid and load fluctuation and the system parameters changing may affect the stability of APF DC bus voltage and the normal operation of APF. The mathematical model of DC bus voltage is established according to power balance principle and a DC bus voltage piecewise reaching law variable structure control algorithm is proposed to solve the ...

A Multi-Pulse Front-End Rectifier System with Electronic Phase-Shifting for Harmonic Mitigation in Motor Drive Applications

DEFF Research Database (Denmark)

Zare, Firuz; Davari, Pooya; Blaabjerg, Frede

2016-01-01

In this paper, an electronic phase-shifting strategy has been optimized for a multi-parallel configuration of line-commutated rectifiers with a common dc-bus voltage used in motor drive application. This feature makes the performance of the system independent of the load profile and maximizes its...

Optimization Model for Headway of a Suburban Bus Route

Directory of Open Access Journals (Sweden)

Xiaohong Jiang

2014-01-01

Full Text Available Due to relatively low passenger demand, headways of suburban bus route are usually longer than those of urban bus route. Actually it is also difficult to balance the benefits between passengers and operators, subject to the service standards from the government. Hence the headway of a suburban bus route is usually determined on the empirical experience of transport planners. To cope with this problem, this paper proposes an optimization model for designing the headways of suburban bus routes by minimizing the operating and user costs. The user costs take into account both the waiting time cost and the crowding cost. The feasibility and validity of the proposed model are shown by applying it to the Route 206 in Jiangning district, Nanjing city of China. Weightages of passengers’ cost and operating cost are further discussed, considering different passenger flows. It is found that the headway and objective function are affected by the weightages largely.

A Novel Time Synchronization Method for Dynamic Reconfigurable Bus

Directory of Open Access Journals (Sweden)

Zhang Weigong

2016-01-01

Full Text Available UM-BUS is a novel dynamically reconfigurable high-speed serial bus for embedded systems. It can achieve fault tolerance by detecting the channel status in real time and reconfigure dynamically at run-time. The bus supports direct interconnections between up to eight master nodes and multiple slave nodes. In order to solve the time synchronization problem among master nodes, this paper proposes a novel time synchronization method, which can meet the requirement of time precision in UM-BUS. In this proposed method, time is firstly broadcasted through time broadcast packets. Then, the transmission delay and time deviations via three handshakes during link self-checking and channel detection can be worked out referring to the IEEE 1588 protocol. Thereby, each node calibrates its own time according to the broadcasted time. The proposed method has been proved to meet the requirement of real-time time synchronization. The experimental results show that the synchronous precision can achieve a bias less than 20 ns.

Optimal Design of the Feeder-Bus Network Based on the Transfer System

Directory of Open Access Journals (Sweden)

Lianbo Deng

2013-01-01

Full Text Available This paper studied the classic feeder-bus network design problem (FBNDP, which can be described as follows: for the passenger travel demand between rail stations and bus stops on a given urban transit network, it designs the optimal feeder bus routes and frequencies so as to minimize the passengers’ travel expense and the operator’s cost. We extended the demand pattern of M-to-1 in most existing researches to M-to-M. We comprehensively considered the passenger travel cost, which includes the waiting and riding cost on the bus, riding cost on rail, and transfer cost between these two transportation modes, and presented a new genetic algorithm that determines the optimal feeder-bus operating frequencies under strict constraint conditions. The numerical examples under different demand patterns have been experienced and analysed, which showed the robustness and efficiency of the presented algorithm. We also found that the distribution pattern of the travel demand has a significant influence on the feeder-bus network construction.

Modelling modal shift due to the enhanced level of bus service

Directory of Open Access Journals (Sweden)

P. Vedagiri

2009-06-01

Full Text Available This study is concerned with the estimation of the probable shift of auto-rickshaw (three wheeled motorized para-transit vehicle users to the bus due to an increase in its level of service after providing exclusive bus lanes on Indian city roads carrying heterogeneous traffic. The quantum of an increase in the level of bus service due to the introduction of an exclusive bus lane was determined using a recently developed simulation model of heterogeneous traffic flow. The data on other factors (variables that might cause modal shift from the auto-rickshaw to the bus was collected conducting a home-interview survey based on the stated preference approach. A binary logit model of mode-choice was then calibrated using the collected data and the model was also validated using a holdout sample. A mode-choice probability curve to depict the possible shift of auto-rickshaw users to the bus is developed taking difference in the travel times of two-modes as the basis to serve as a user friendly tool to analyze the possible modal shift for a wide range of the values of the involved variables.

Bringing MapReduce Closer To Data With Active Drives

Science.gov (United States)

Golpayegani, N.; Prathapan, S.; Warmka, R.; Wyatt, B.; Halem, M.; Trantham, J. D.; Markey, C. A.

2017-12-01

Moving computation closer to the data location has been a much theorized improvement to computation for decades. The increase in processor performance, the decrease in processor size and power requirement combined with the increase in data intensive computing has created a push to move computation as close to data as possible. We will show the next logical step in this evolution in computing: moving computation directly to storage. Hypothetical systems, known as Active Drives, have been proposed as early as 1998. These Active Drives would have a general-purpose CPU on each disk allowing for computations to be performed on them without the need to transfer the data to the computer over the system bus or via a network. We will utilize Seagate's Active Drives to perform general purpose parallel computing using the MapReduce programming model directly on each drive. We will detail how the MapReduce programming model can be adapted to the Active Drive compute model to perform general purpose computing with comparable results to traditional MapReduce computations performed via Hadoop. We will show how an Active Drive based approach significantly reduces the amount of data leaving the drive when performing several common algorithms: subsetting and gridding. We will show that an Active Drive based design significantly improves data transfer speeds into and out of drives compared to Hadoop's HDFS while at the same time keeping comparable compute speeds as Hadoop.

The Gozo discovery bus : a successful experiment

OpenAIRE

Vella, Maryrose

2008-01-01

The introduction of a tourist discovery bus in Gozo came about as a result of an EU Project which is part of the Interreg III B Archimed programmes in which the Islands and Small States Institute of the University of Malta participated. Other countries participating in this programme besides Malta, represented by the Islands and Small States Institute, are Italy, Cyprus and Greece. The discovery bus service was aimed at encouraging more tourists to come to Gozo and enabling them to visit stra...

Review of bus drivers' occupational stress and stress prevention

NARCIS (Netherlands)

Kompier, M.A.J.; Di Martino, V.

1995-01-01

Although heterogeneous in methodology and content, 32 studies from 13 countries on bus drivers' work and health are similar in their conclusions. Bus-driving–characterized by high demands, low control and low support – can be regarded as a classic example of high-strain occupation, with high risks

Using Assessment to Drive the Reform of Schooling: Time to Stop Pursuing the Chimera?

Science.gov (United States)

Torrance, Harry

2011-01-01

Internationally, over the last 20-30 years, changing the procedures and processes of assessment has come to be seen, by many educators as well as policy-makers, as a way to frame the curriculum and drive the reform of schooling. Such developments have often been manifested in large scale, high stakes testing programmes. At the same time…

DWPF Melter No.2 Prototype Bus Bar Test Report

International Nuclear Information System (INIS)

Gordon, J.

2003-01-01

Characterization and performance testing of a prototype DWPF Melter No.2 Dome Heater Bus Bar are described. The prototype bus bar was designed to address the design features of the existing system which may have contributed to water leaks on Melter No.1. Performance testing of the prototype revealed significant improvement over the existing design in reduction of both bus bar and heater connection maximum temperature, while characterization revealed a few minor design and manufacturing flaws in the bar. The prototype is recommended as an improvement over the existing design. Recommendations are also made in the area of quality control to ensure that critical design requirements are met

76 FR 37393 - FY 2011 Discretionary Livability Funding Opportunity; Section 5309 Bus and Bus Facilities...

Science.gov (United States)

2011-06-27

... 90 percent Federal share for the total cost of a biodiesel bus. The Act also allows a 90 percent... transit systems or roadways. iv. Will improve accessibility and transport services for economically...

American Fuel Cell Bus Project Evaluation. Second Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, Leslie [National Renewable Energy Lab. (NREL), Golden, CO (United States); Post, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2015-09-01

This report presents results of the American Fuel Cell Bus (AFCB) Project, a demonstration of fuel cell electric buses operating in the Coachella Valley area of California. The prototype AFCB was developed as part of the Federal Transit Administration's (FTA's) National Fuel Cell Bus Program. Through the non-profit consortia CALSTART, a team led by SunLine Transit Agency and BAE Systems developed a new fuel cell electric bus for demonstration. SunLine added two more AFCBs to its fleet in 2014 and another in 2015. FTA and the AFCB project team are collaborating with the U.S. Department of Energy (DOE) and DOE's National Renewable Energy Laboratory to evaluate the buses in revenue service. This report summarizes the performance results for the buses through June 2015.

Bavarian liquid hydrogen bus demonstration project - safety, licensing and acceptability aspects

Energy Technology Data Exchange (ETDEWEB)

Wurster, R.; Knorr, H.; Pruemm, W.

1999-07-01

A regular 12 m city bus of the MAN SL 202 type with an internal combustion engine adapted to hydrogen operation and auxiliary gasoline operation was demonstrated in the Bavarian cities of Erlangen and Munich between April 1996 and August 1998. Three bus operators, Erlanger Stadtwerke, Stadtwerke Muenchen and Autobus Oberbayern were testing the bus in three different operating schemes. In order to be able to perform this worldwide first public demonstration of a liquid hydrogen (LH{sub 2}) city bus in regular service, several requirements with respect to safety, licensing, training and acceptability had to be fulfilled. These activities were focusing mainly on the hydrogen specific issues such as (a) integration of onboard LH{sub 2} storage vessels, piping and instrumentation, (b) implementation of storage and refueling infrastructure in the operators' yards, (c) adaptation of the maintenance garages, (d) training of operating and maintenance personnel. During phase II of the demonstration activity a poll was performed on passengers traveling onboard the hydrogen-powered city bus in order to determined the level of acceptance among the users of the bus. The bus was designed and manufactured by MAN Nutzfahrzeuge Aktiengesellschaft. The cryogenic fuel storage and the refueling equipment were designed and manufactured by Linde AG. The realization of the hardware was financially supported by the European Commission (EC) within the Euro-Quebec Hydro-Hydrogen Pilot Project. The demonstration phase was financially supported by EC and the Bavarian State Government. Ludwig-Boelkow-Systemtechnik performed project monitoring for both funding organizations. The presentation will summarize the most important results of this demonstration phase and will address the measures undertaken in order to get the bus, the refueling infrastructure and the maintenance and operating procedures approved by the relevant authorities.

Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus Preliminary Evaluation Results

Science.gov (United States)

2008-10-16

This report describes operations at Connecticut Transit (CTTRANSIT) in Hartford for one prototype fuel cell bus and three new diesel buses operating from the same location. The report discusses the planned fuel cell bus demonstration and equipment us...

Unlicensed driving and other related health risk behaviors: a study of Montana high school students.

Science.gov (United States)

Hanna, Christian L; Laflamme, Lucie; Elling, Berty; Möller, Jette

2013-05-01

Health risk behaviors tend to cluster in young people, not least among young drivers. Less is known about the health risk profile of young unlicensed drivers. This study investigates health risk behaviors among young unlicensed drivers compared to both their licensed and driving peers, and their non-driving peers. High school students participating in the Youth Risk Behavior Surveillance System in Montana (US) and age-eligible to have a driver's license were studied (n=5985), categorized according to their self-reported car driving and license practice (licensed driving, unlicensed driving, and non-driving). Ten health risk behaviors, of which four were related to car riding/driving, were considered. Multinomial logistic regression was used to compile sex-specific odds ratios (with 95% confidence intervals) of adopting those behaviors using licensed drivers as a reference and adjusting for age and race/ethnicity. Health risk behaviors tended to be more common among unlicensed drivers than other groups, although some behaviors were prevalent in all groups (i.e., alcohol use and lack of seat belt use). As a consequence, for both male and female students, there was a significant association between unlicensed driving and most health risk behaviors, except for being involved in a physical fight and riding with a drinking driver among female students. Young unlicensed drivers are more likely than licensed drivers to adopt several health risk behaviors both in car driving/riding or otherwise, in particular alcohol use and cigarette smoking. This challenges any simplistic approach as unlicensed driving in youth is not an isolated act suggesting public health and traffic safety initiatives. Copyright © 2013 Elsevier Ltd. All rights reserved.

SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: First Results Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Chandler, K.

2011-03-01

This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. This report provides the early data results and implementation experience of the AT fuel cell bus since it was placed in service.

Digital bus technology in new coal-fired plants

Energy Technology Data Exchange (ETDEWEB)

Blaney, J.; Murray, J. [Emerson Process Management (United States)

2007-10-15

The main issues associated with including digital bus technology such as Foundation fieldbus, Profibus-DP or DeviceNet, in a coal-fired power plant are deciding which systems to install and determining how to implement it. Although still new, digital bus experiences to date have shown that the technology performs solidly and when wiring best practices are followed a significantly shorted commissioning cycle can be achieved. 1 fig., 2 tabs.

THE PREVALENCE OF MUSCULOSKELETAL DISORDERS AMONG BUS DRIVERS IN TRICITY

Directory of Open Access Journals (Sweden)

Lalit

2015-10-01

Full Text Available Background: Musculoskeletal disorders are widespread in many countries around the world. It has been reported that about 58 percent of the world's population over the age of 10 years spent one third of their life span at work. The population at a high risk include nursing facilities, transportation, mining, food processing, leather tanning, heavy and light manufacturing. Transport workers have been found to be at high risk of developing work related musculoskeletal disorders (WRMSDs. There has been literature evidence regarding the prevalence of musculoskeletal disorders in bus drivers of various cities of different countries. But no study has been done so far in Tricity (Chandigarh, Panchkula and Mohali for the same. The purpose of this study is to investigate the prevalence and characteristics of work related musculoskeletal disorders (WRMSDs among bus drivers of Tricity. Methods: 300 bus drivers were included in the study according to the inclusion and exclusion criteria. The standardized Nordic questionnaire for musculoskeletal disorder and a self administered questionnaire were filled by therapist after the personal interview of each driver. Results: Unpaired t test was used to measure the difference in variable of two groups and Karl Pearson’s correlation coefficient was used to determine the correlation between two entities. In the present study, the subjects were in the age group of 25 to 50 years. Out of the total sample of 300 male bus drivers in Tricity, 159 reported that they had WRMSDs. The prevalence of WRMSDs among bus drivers in Tricity was 53%. In present study, the prevalence of low back pain was highest among the bus drivers that are 30.3%, then neck pain 17.3%, knee pain 14.7%, shoulder 6.3%, ankle and feet 5.7%, upper back 4%, hip and thigh 4%, elbow 1.3% and wrist and hand 1.3%. Thus low back pain, neck pain and knee pain are the most prevalent WRMSDs amongst bus drivers. Conclusions: Work-related biomechanical

School buses, air pollution and children's health: follow-up report

Energy Technology Data Exchange (ETDEWEB)

Perrotta, K. [Clean Air Partnership, Toronto, ON (Canada)], email: Kperrotta@cleanairpartnership.org

2010-10-15

This document is designed to be a follow-up report to the Ontario Public Health Association (OPHA) school bus report published in 2005, and was produced through a collaboration between the Clean Air Partnership and the OPHA. The level of awareness of school bus emissions are evaluated in this report. The document also provides a review of projects handled by the federal government, programs developed by governments of other provinces and the policies followed by school boards in other provinces, to mitigate emissions and exposures related to school buses. Several recommendations were made, including the replacement of older school buses, adapt the routes considering the emissions generated and promote the use of biodiesel to reduce emissions of air pollutants and greenhouse gases. 36 refs, 8 tabs.

CRADA Final Report for CRADA Number ORNL98-0521 : Development of an Electric Bus Inverter Based on ORNL Auxiliary Resonant Tank (ART) Soft-Switching Technology; TOPICAL

International Nuclear Information System (INIS)

Ayers, C.W.

2001-01-01

The Power Electronics and Electric Machinery Research Center (PEEMRC) of Oak Ridge National Laboratory (ORNL) has for many years been developing technologies for power converters for motor drives and many other applications. Some of the research goals are to improve efficiency and reduce audible and electromagnetic interference noise generation for inverters and the driven loads. The converters are being required to produce more power with reduced weight and volume, which requires improvements in heat removal from the electronics, as well as improved circuit designs that have fewer electrical losses. PEEMRC has recently developed and patented a soft-switching inverter topology called an Auxiliary Resonant Tank (ART), and this design has been tested and proven at ORNL using a 10-kW laboratory prototype. The objective of this project was to develop, test, and install the ART inverter technology in an electric transit bus with the final goal of evaluating performance of the ORNL inverter under field conditions in a vehicle. A scaled-up inverter with the capacity to drive a 22-e bus was built based on the 10-kW ORNL laboratory prototype ART soft-switching inverter. Most (if not all) commercially available inverters for traction drive and other applications use hard-switching inverters. A Cooperative Research and Development Agreement was established with the Chattanooga Area Regional Transit Authority (CARTA), the Electric Transit Vehicle Institute (ETVI), and Advanced Vehicle Systems (AVS), all of Chattanooga, along with ORNL. CARTA, which maintains and operates the public transit system in Chattanooga, provided an area for testing the vehicle alongside other similar vehicles in the normal operating environment. ETVI offers capabilities in standardized testing and reporting and also provides exposure in the electric transit vehicle arena for ORNL's technologies. The third Chattanooga partner, (AVS) manufactures all-electric and hybrid electric transit buses using

IMPACTS OF BUS STOP IMPROVEMENTS

Science.gov (United States)

2018-03-23

Improving bus stops by providing shelters, seating, signage, and sidewalks is relatively inexpensive and popular among riders and local officials. Making such improvements, however, is not often a priority for U.S. transit providers because of compet...

Energy DataBus (Fact Sheet)

Energy Technology Data Exchange (ETDEWEB)

2013-07-01

NREL has developed the Energy DataBus, an open-sourced software that collects massive amounts of energy-related data at second-to-second intervals; stores it in a massive, scalable database; and turns it into useful information.

The effects of in-vehicle tasks and time-gap selection while reclaiming control from adaptive cruise control (ACC) with bus simulator.

Science.gov (United States)

Lin, Tsang-Wei; Hwang, Sheue-Ling; Su, Jau-Ming; Chen, Wan-Hui

2008-05-01

This research aimed to find out the effects of in-vehicle distractions and time-gap settings with a fix-based bus driving simulator in a following scenario. Professional bus drivers were recruited to perform in-vehicle tasks while driving with adaptive cruise control (ACC) of changeable time-gap settings in freeway traffic. Thirty subjects were divided equally into three groups for different in-vehicle task modes (between subjects), including no task distraction, hands-free, and manual modes. Further, time-gap settings for the experimental ACC were: shorter than 1.0 s, 1.0-1.5 s, 1.5-2.0 s, and longer than 2.0 s (within subjects). Longitudinal (mean headway, forward collision rate, and response time) and lateral control (mean lateral lane position and its standard deviation) performance was assessed. In the results, longitudinal control performance was worsened by both shorter time-gaps and heavier in-vehicle tasks. But the interaction indicated that the harm by heavier in-vehicle distraction could be improved by longer time-gaps. As for the lateral control, it would only be negatively affected by shorter time-gap settings. This research indicates the effects of time-gaps and in-vehicle distraction, as well as the interaction. Proper time-gap selection under different in-vehicle distractions can help avoid accidents and keep safe.

Exposure Assessment of Diesel Bus Emissions

Directory of Open Access Journals (Sweden)

Werner Hofmann

2006-12-01

Full Text Available The goal of this study was to measure ultrafine particle concentrations with diameters less than 1 μm emitted by diesel buses and to assess resulting human exposure levels. The study was conducted at the Woolloongabba Busway station in Brisbane, Australia in the winter months of 2002 during which temperature inversions frequently occurred. Most buses that utilize the station are fuelled by diesel, the exhaust of which contains a significant quantity of particle matter. Passengers waiting at the station are exposed to these particles emitted from the buses. During the course of this study, passenger census was conducted, based on video surveillance, yielding person-by-person waiting time data. Furthermore, a bus census revealed accurate information about the total number of diesel versus Compressed Natural Gas (CNG powered buses. Background (outside of the bus station and platform measurements of ultrafine particulate number size distributions were made to determine ambient aerosol concentrations. Particle number exposure concentration ranges from 10 and 40 to 60% of bus related exhaust fumes. This changes dramatically when considering the particle mass exposure concentration, where most passengers are exposed to about 50 to 80% of exhaust fumes. The obtained data can be very significant for comparison with similar work of this type because it is shown in previous studies that exhaust emissions causes cancer in laboratory animals. It was assumed that significant differences between platform and background distributions were due to bus emissions which, combined with passenger waiting times, yielded an estimate of passenger exposure to ultrafine particles from diesel buses. From an exposure point of view, the Busway station analyzed resembles a street canyon. Although the detected exhaust particle concentration at the outbound platform is found to be in the picogram range, exposure increases with the time passengers spend on the platform

Performance Analysis of Trans-Jakarta Bus Suburban Service Move-Across Greater Jakarta

Science.gov (United States)

Tangkudung, ESW; Widyadayinta, C.

2018-03-01

Trans-Jakarta have developed their services scope as Suburban Service or Feeder move-across service that operate from greater Jakarta into Jakarta central vice versa. One of the route is Ciputat – Bundaran Hotel Indonesia (Tosari) and integrated with corridor 1 (one) and 8 (eight). This service is not travel on the exclusive lane or bus-way. Objective of Government Jakarta to provide this service is to decrease private car to enter the central of Jakarta. The objective of this study is to find the performance of the service. Survey have conducted static and dynamic on work day to get variable of travel time and delay, waiting time of passenger at the bus stop, headway and ridership of the bus. Service Standard Minimum of Trans-Jakarta have compared with the result of variable headway, travel speed, and waiting time at bus stop as concern of all the passengers. Analysis use correlation test method and linear regression model have done. The performance of Trans-Jakarta bus suburban service, based on travel speed indicator is fairly bad, only 8.1% of trip could comply with Minimum Service Standard. Bus performance based on the indicator of density in the bus is good, where all points are below the maximum limit i.e. 8 people/m2 at peak hour and 5 people/m2 at off-peak hour.

Operating Time Division for a Bus Route Based on the Recovery of GPS Data

Directory of Open Access Journals (Sweden)

Jian Wang

2017-01-01

Full Text Available Bus travel time is an important source of data for time of day partition of the bus route. However, in practice, a bus driver may deliberately speed up or slow down on route so as to follow the predetermined timetable. The raw GPS data collected by the GPS device equipped on the bus, as a result, cannot reflect its real operating conditions. To address this concern, this study first develops a method to identify whether there is deliberate speed-up or slow-down movement of a bus. Building upon the relationships between the intersection delay, link travel time, and traffic flow, a recovery method is established for calculating the real bus travel time. Using the dwell time at each stop and the recovered travel time between each of them as the division indexes, a sequential clustering-based time of day partition method is proposed. The effectiveness of the developed method is demonstrated using the data of bus route 63 in Harbin, China. Results show that the partition method can help bus enterprises to design reasonable time of day intervals and significantly improve their level of service.

VME bus based microcomputer system boards

International Nuclear Information System (INIS)

Chandra, A.K.; Ganesh, G.; Mayya, Anuradha; Chachondia, A.S.; Premraj, M.K.

1991-01-01

Several operator information systems for nuclear plants has been developed in the Division and these have involved extensive use of microcomputer boards for achieving various functions. Standard VME bus based boards have been developed to provide the most used functions. These boards have been fabricated and tested and used in several systems including Channel Temperature Monitoring systems, Disturbance Recording Systems etc. and are also proposed to be used in additional systems under developement. The use of standard bus and boards provides considerable savings in engineering time, prototyping, testing and evaluation costs, and maintenance support. This report desribes the various boards developed and the functions available on each. (author). 4 refs., 11 figs., 3 appendixes

Autonomous Navigation and Obstacle Avoidance of a Micro-Bus

Directory of Open Access Journals (Sweden)

Carlos Fernández

2013-04-01

Full Text Available At present, the topic of automated vehicles is one of the most promising research areas in the field of Intelligent Transportation Systems (ITS. The use of automated vehicles for public transportation also contributes to reductions in congestion levels and to improvements in traffic flow. Moreover, electrical public autonomous vehicles are environmentally friendly, provide better air quality and contribute to energy conservation. The driverless public transportation systems, which are at present operating in some airports and train stations, are restricted to dedicated roads and exhibit serious trouble dynamically avoiding obstacles in the trajectory. In this paper, an electric autonomous mini-bus is presented. All datasets used in this article were collected during the experiments carried out in the demonstration event of the 2012 IEEE Intelligent Vehicles Symposium that took place in Alcalá de Henares (Spain. The demonstration consisted of a route 725 metres long containing a list of latitude-longitude points (waypoints. The mini-bus was capable of driving autonomously from one waypoint to another using a GPS sensor. Furthermore, the vehicle is provided with a multi-beam Laser Imaging Detection and Ranging (LIDAR sensor for surrounding reconstruction and obstacle detection. When an obstacle is detected in the planned path, the planned route is modified in order to avoid the obstacle and continue its way to the end of the mission. On the demonstration day, a total of 196 attendees had the opportunity to get a ride on the vehicles. A total of 28 laps were successfully completed in full autonomous mode in a private circuit located in the National Institute for Aerospace Research (INTA, Spain. In other words, the system completed 20.3 km of driverless navigation and obstacle avoidance.

Connecticut Transit (CTTRANSIT) Fuel Cell Transit Bus: Preliminary Evaluation Results

Energy Technology Data Exchange (ETDEWEB)

Chandler, K.; Eudy, L.

2008-10-01

This report provides preliminary results from a National Renewable Energy Laboratory evaluation of a protoptye fuel cell transit bus operating at Connecticut Transit in Hartford. Included are descriptions of the planned fuel cell bus demonstration and equipment; early results and agency experience are also provided.

Bus network redesign for inner southeast suburbs of Melbourne, Australia

Science.gov (United States)

Pandangwati, S. T.; Milyanab, N. A.

2017-06-01

Public transport is the most effective mode of transport in the era of climate change and oil depletion. It can address climate change issues by reducing urban greenhouse gas emission and oil consumption while at the same time improving mobility. However, many public transport networks are not effective and instead create high operating costs with low frequencies and occupancy. Melbourne is one example of a metropolitan area that faces this problem. Even though the city has well-integrated train and tram networks, Melbourne’s bus network still needs to be improved. This study used network planning approach to redesign the bus network in the City of Glen Eira, a Local Government Area (LGA) in the southeastern part of Metropolitan Melbourne. The study area is the area between Gardenvale North and Oakleigh Station, as well as between Caulfield and Patterson Stations. This area needs network improvement mainly because of the meandering bus routes that run within it. This study aims to provide recommendations for improving the performance of bus services by reducing meandering routes, improving transfer point design and implementing coordinated timetables. The recommendations were formulated based on a ‘ready-made’ concept to increase bus occupancy. This approach can be implemented in other cities with similar problems and characteristics including those in Indonesia.

SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Fourth Results Report

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Chandler, K.

2013-01-01

SunLine Transit Agency, which provides public transit services to the Coachella Valley area of California, has demonstrated hydrogen and fuel cell bus technologies for more than 10 years. In May 2010, SunLine began demonstrating the advanced technology (AT) fuel cell bus with a hybrid electric propulsion system, fuel cell power system, and lithium-based hybrid batteries. This report describes operations at SunLine for the AT fuel cell bus and five compressed natural gas buses. The U.S. Department of Energy's National Renewable Energy Laboratory (NREL) is working with SunLine to evaluate the bus in real-world service to document the results and help determine the progress toward technology readiness. NREL has previously published three reports documenting the operation of the fuel cell bus in service. This report provides a summary of the results with a focus on the bus operation from February 2012 through November 2012.

Bicycle-bus conflict area study.

Science.gov (United States)

2009-11-01

Increasing bicycle use and bus ridership are both desirable policy goals : from a sustainability standpoint, but on city streets these two modes of : transport are often in conflict. While occupying opposite ends of the size : and weight spectrum, th...

Terminals for Suburb Bus Transport in Bratislava

Science.gov (United States)

Schlosser, Tibor; Schlosser, Peter; Cápayová, Silvia; Hodáková, Dominika

2017-10-01

The main objective of this article is to describe the strategy for development of the public transport terminals in the city of Bratislava, Capital of Slovak Republic. The reason goes from the private operator Slovak Lines, who operates the suburb bus transport in the agglomeration of the city. For this operator was created a transport model, while placing emphasis on optimizing the compliance of suburban public transport with urban public transport in the city of Bratislava and evaluating the significance of the new Bus Station to be constructed at Mlynské Nivy - in a new down town centre of the city. The main issue is to ensure the best available offer of public transport (PT) to passengers in the Bratislava agglomeration. The subject of the study was oriented to specify and propose changes in the transport infrastructure and integrated public transport organisation on the area of the city in terms of the significant position of the new Mlynské Nivy Bus Station (MN BS), which is under preparation with realization in the year 2017.

Next Generation Environmentally-Friendly Driving Feedback Systems Research and Development

Energy Technology Data Exchange (ETDEWEB)

Barth, Matthew [Regents Of The University Of California, Riverside, CA (United States); Boriboonsomsin, Kanok [Regents Of The University Of California, Riverside, CA (United States)

2014-12-31

The objective of this project is to design, develop, and demonstrate a next-generation, federal safety- and emission-complaint driving feedback system that can be deployed across the existing vehicle fleet and improve fleet average fuel efficiency by at least 2%. The project objective was achieved with the driving feedback system that encourages fuel-efficient vehicle travel and operation through: 1) Eco-Routing Navigation module that suggests the most fuel-efficient route from one stop to the next, 2) Eco-Driving Feedback module that provides sensible information, recommendation, and warning regarding fuel-efficient vehicle operation, and 3) Eco-Score and Eco-Rank module that provides a means for driving performance tracking, self-evaluation, and peer comparison. The system also collects and stores vehicle travel and operation data, which are used by Algorithm Updating module to customize the other modules for specific vehicles and adapts them to specific drivers over time. The driving feedback system was designed and developed as an aftermarket technology that can be retrofitted to vehicles in the existing fleet. It consists of a mobile application for smart devices running Android operating system, a vehicle on-board diagnostics connector, and a data server. While the system receives and utilizes real-time vehicle and engine data from the vehicle’s controller area network bus through the vehicle’s on-board diagnostic connector, it does not modify or interfere with the vehicle’s controller area network bus, and thus, is in compliance with federal safety and emission regulations. The driving feedback system was demonstrated and then installed on 45 vehicles from three different fleets for field operational test. These include 15 private vehicles of the general public, 15 pickup trucks of the California Department of Transportation that are assigned to individual employees for business use, and 15 shuttle buses of the Riverside Transit Agency that are used

Brazilian hybrid electric fuel cell bus

Energy Technology Data Exchange (ETDEWEB)

Miranda, P.E.V.; Carreira, E.S. [Coppe-Federal Univ. of Rio de Janeiro (Brazil). Hydrogen Lab.

2010-07-01

The first prototype of a hybrid electric fuel cell bus developed with Brazilian technology is unveiled. It is a 12 m urban-type, low-floor, air-conditioned bus that possesses three doors, air suspension, 29 seats and reversible wheelchair site. The bus body was built based on a double-deck type monoblock vehicle that is able to sustain important load on its roof. This allowed positioning of the type 3 hydrogen tanks and the low weight traction batteries on the roof of the vehicles without dynamic stabilization problems. A novel hybrid energy configuration was designed in such a way that the low-power (77 kWe) fuel cell works on steady-state operation mode, not responding directly to the traction motor load demand. The rate of kinetic energy regeneration upon breaking was optimized by the use of an electric hybrid system with predominance of batteries and also by utilizing supercapacitors. The electric-electronic devices and the security control softwares for the auxiliary and traction systems were developed in-house. The innovative hybrid-electric traction system configuration led to the possibility to decrease the fuel cell power, with positive impact on weight and system volume reduction, as well as to significantly decrease the hydrogen consumption. (orig.)

Bus Stops and Pedestrian-Motor Vehicle Collisions in Lima, Peru: A Matched Case-Control Study

Science.gov (United States)

Quistberg, D. Alex; Koepsell, Thomas D.; Johnston, Brian D.; Boyle, Linda Ng; Miranda, J. Jaime; Ebel, Beth E.

2015-01-01

Objective To evaluate the relationship between bus stop characteristics and pedestrian-motor vehicle collisions. Design Matched case-control study where the units of study were pedestrian crossing. Setting Random sample of 11 police commissaries in Lima, Peru. Data collection occurred from February, 2011 to September, 2011. Participants 97 intersection cases representing 1,134 collisions and 40 mid-block cases representing 469 collisions that occurred between October, 2010 and January, 2011 and their matched controls. Main Exposures Presence of a bus stop and specific bus stop characteristics. Main Outcome Occurrence of a pedestrian-motor vehicle collision. Results Intersections with bus stops were three times more likely to have a pedestrian-vehicle collision (OR 3.28, 95% CI 1.53-7.03), relative to intersections without bus stops. Both formal and informal bus stops were associated with a higher odds of a collision at intersections (OR 6.23, 95% CI 1.76-22.0 and OR 2.98, 1.37-6.49). At mid-block sites, bus stops on a bus-dedicated transit lane were also associated with collision risk (OR 2.36, 95% CI 1.02-5.42). All bus stops were located prior to the intersection, contrary to practices in most high income countries. Conclusions In urban Lima, the presence of a bus stop was associated with a three-fold increase in risk of a pedestrian collision. The highly competitive environment among bus companies may provide an economic incentive for risky practices such as dropping off passengers in the middle of traffic and jockeying for position with other buses. Bus stop placement should be considered to improve pedestrian safety. PMID:24357516

Active Power Filter DC Bus Voltage Piecewise Reaching Law Variable Structure Control

Directory of Open Access Journals (Sweden)

Baolian Liu

2014-01-01

Full Text Available The DC bus voltage stability control is one key technology to ensure that Active Power Filter (APF operates stably. The external disturbances such as power grid and load fluctuation and the system parameters changing may affect the stability of APF DC bus voltage and the normal operation of APF. The mathematical model of DC bus voltage is established according to power balance principle and a DC bus voltage piecewise reaching law variable structure control algorithm is proposed to solve the above problem, and the design method is given. The simulation and experiment results proved that the proposed variable structure control algorithm can eliminate the chattering problem existing in traditional variable structure control effectively, is insensitive to system disturbance, and has good robustness and fast dynamic response speed and stable DC bus voltage with small fluctuation. The above advantages ensure the compensation effect of APF.

Reducing School Violence in Florida. Hot Topics: Usable Research.

Science.gov (United States)

Kadel, Stephanie; Follman, Joseph

Violence pervades schools across the nation, disrupting school functioning and preventing students and teachers from learning and teaching. The most effective crisis management and response strategies are designed by a school team that includes administrators, faculty and staff, students, parents, bus drivers and other support staff, as well as…

Optimizing Tailored Bus Bridging Paths

NARCIS (Netherlands)

Gu, Wei; Yu, Jie; Ji, Yuxiong; van der Gun, J.P.T.; Pel, A.J.; Zhang, H. Michael; van Arem, B.

2017-01-01

Metro disruptions due to unexpected events reduce transit system reliability, resulting in significant productivity loss and long passenger delays. Bus bridging strategy is often used to connect stations affected by metro disruptions such that passengers could continue their journey. The literature

A Model of Bus Bunching under Reliability-based Passenger Arrival Patterns

OpenAIRE

Fonzone, Achille; Schmöcker, Jan-Dirk; Liu, Ronghui

2015-01-01

If bus service departure times are not completely unknown to the passengers, non-uniform passenger arrival patterns can be expected. We propose that passengers decide their arrival time at stops based on a continuous logit model that considers the risk of missing services. Expected passenger waiting times are derived in a bus system that allows also for overtaking between bus services. We then propose an algorithm to derive the dwell time of subsequent buses serving a stop in order to illustr...

DESIGN OF CITY BUS LIFT FOR THE HANDICAPPEDS

Directory of Open Access Journals (Sweden)

K. Turgut GÜRSEL

2003-03-01

Full Text Available Although the technological developments, the handicappeds do not take part sufficiently in the social and economic life, because buildings, road construction features and means of the transport are not suitable for them. In this study, a lift for handicappeds was designed, that is supposed to be installed to the middle door of city buses. The lift, whose installation should require a few changes at the bus, is driven by a hydraulic system from the street to the level of the bus floor and vice-versa. In the work, at first a construction was developed in accordance with the dimensions of the middle door of a city bus. After determining of dimensions of all elements, a hydraulic mechanism was constructed, that raises the handicapped, its wheelchair and the platform. Furthermore the construction of the elements of the system were determined, and its proofs of strength analysis were indicated

The Bus Extension Module Design and Verification of POSAFE-Q Using LVDS

International Nuclear Information System (INIS)

Lee, Youn Sang; Song, Seung Whan; No, Young Hun; Yoo, Kwan Woo

2012-01-01

This paper described the Bus Extension Module using Low Voltage Differential Signal (LVDS). A Bus Extension Module use Safety-Related PLC (Programmable Logic Controller), called POSAFE-Q (made by POSCO ICT), for handling many data (I/O) extension rack. A processor module of POSAFE-Q can control I/O Module installed another rack. This paper explains Bus Extension Module and Data transfer technology using LVDS. (author)

Improvement of multiprocessing performance by using optical centralized shared bus

Science.gov (United States)

Han, Xuliang; Chen, Ray T.

2004-06-01

With the ever-increasing need to solve larger and more complex problems, multiprocessing is attracting more and more research efforts. One of the challenges facing the multiprocessor designers is to fulfill in an effective manner the communications among the processes running in parallel on multiple multiprocessors. The conventional electrical backplane bus provides narrow bandwidth as restricted by the physical limitations of electrical interconnects. In the electrical domain, in order to operate at high frequency, the backplane topology has been changed from the simple shared bus to the complicated switched medium. However, the switched medium is an indirect network. It cannot support multicast/broadcast as effectively as the shared bus. Besides the additional latency of going through the intermediate switching nodes, signal routing introduces substantial delay and considerable system complexity. Alternatively, optics has been well known for its interconnect capability. Therefore, it has become imperative to investigate how to improve multiprocessing performance by utilizing optical interconnects. From the implementation standpoint, the existing optical technologies still cannot fulfill the intelligent functions that a switch fabric should provide as effectively as their electronic counterparts. Thus, an innovative optical technology that can provide sufficient bandwidth capacity, while at the same time, retaining the essential merits of the shared bus topology, is highly desirable for the multiprocessing performance improvement. In this paper, the optical centralized shared bus is proposed for use in the multiprocessing systems. This novel optical interconnect architecture not only utilizes the beneficial characteristics of optics, but also retains the desirable properties of the shared bus topology. Meanwhile, from the architecture standpoint, it fits well in the centralized shared-memory multiprocessing scheme. Therefore, a smooth migration with substantial

Black silicon with black bus-bar strings

DEFF Research Database (Denmark)

Davidsen, Rasmus Schmidt; Tang, Peter Torben; Mizushima, Io

2016-01-01

We present the combination of black silicon texturing and blackened bus-bar strings as a potential method for obtaining all-black solar panels, while using conventional, front-contacted solar cells. Black silicon was realized by mask-less reactive ion etching resulting in total, average reflectance...... below 0.5% across a 156x156 mm2 silicon wafer. Black bus-bars were realized by oxidized copper resulting in reflectance below 3% in the entire visible wavelength range. The combination of these two technologies may result in aesthetic, all-black panels based on conventional, front-contacted solar cells...

Air flow through a non-airconditioned bus with open windows

Indian Academy of Sciences (India)

Thus, bus travel which is the backbone of public transport in India will continue ... was not possible to replicate the same Reynolds number as in a real bus. With the .... The Kolmogorov time scale, τη can be estimated to be 6 × 10. −3 s. Thus ...

Identification of voltage stability condition of a power system using measurements of bus variables

Directory of Open Access Journals (Sweden)

Durlav Hazarika

2014-12-01

Full Text Available Several online methods were proposed for investigating the voltage stability condition of an interconnected power system using the measurements of voltage and current phasors at a bus. For this purpose, phasor measurement units (PMUs are used. A PMU is a device which measures the electrical waves on an electrical network, using a common time source (reference bus for synchronisation. This study proposes a method for online monitoring of voltage stability condition of a power system using measurements of bus variables namely – (i real power, (ii reactive power and (iii bus voltage magnitude at a bus. The measurements of real power, reactive power and bus voltage magnitude could be extracted/captured from a smart energy meter. The financial involvement for implementation of the proposed method would significantly lower compared with the PMU-based method.

Annoyance evaluation and the effect of noise on the health of bus drivers

Directory of Open Access Journals (Sweden)

Portela S Bruno

2013-01-01

Full Text Available In the present study, we evaluated annoyance and the effects of noise on the health of bus drivers. For that, 200 bus drivers from a public transport company participated in a cross-sectional study. Annoyance and effects on health was measured with analog scale: Sleep quality, occurrence of tinnitus, headache, irritation, and annoyance from bus engine, traffic, and passengers. Data of age and working time of bus drivers also were obtained. For noise exposure, LA eq was evaluated in 80 buses. Statistical analysis consisted of mean, standard deviation, minimum, and maximum, Kruskal-Wallis test with post-hoc Dunn, one-way ANOVA with post-hoc Tukey and Spearman′s correlation coefficient. Results indicate three groups of bus drivers (not annoyed: (N.A., a little annoyed (L.A. and highly annoyed (H.A.. The group H.A. was younger and with less working time in relation to others, with a significant difference only for age. Regarding sleep quality, there was no significant difference. For results on the occurrence of tinnitus, headache and irritation after work, group H.A. had significantly higher means. Result of annoyance to the bus engine was significantly higher in H.A. than in L.A. and N.A. Annoyance to traffic and passengers, no significant differences were found, but the highest results were found for L.A., followed by H.A. and N.A. Equivalent sound pressure level in buses was above of the limit for occupational comfort. It was concluded that bus drivers has considerable level of noise annoyance and some health effects are perceived. The noise is a factor discomfort ergonomic that may cause effects on health of bus drivers. This study aims to evaluate annoyance and the effects of noise on the health of bus drivers. Cross-sectional study with buses and bus drivers. For that, 200 bus drivers from a public transport company participated in a cross-sectional study. Annoyance and effects on health was measured with analog scale: Sleep quality

Using microcomputers for lighting appliance control using a DALI bus

Directory of Open Access Journals (Sweden)

Sysala Tomas

2016-01-01

Full Text Available Article concerns the DALI bus theoretical and practical aspects. The DALI bus is a modern technology developed especially for illumination systems control. Authors are outlining communication basic principles related to the physical layer and going up to more complex data transactions among particular devices. The article main topic is aimed at two device models development based on microcontroller and exploiting that technology. The first of those two devices is a DALI slave unit enabling the light source or multi switch with light indication components control via DALI bus. The second device measures the ambient illumination intensity and it also detects errors in the load.

Parameters Design for a Parallel Hybrid Electric Bus Using Regenerative Brake Model

Directory of Open Access Journals (Sweden)

Zilin Ma

2014-01-01

Full Text Available A design methodology which uses the regenerative brake model is introduced to determine the major system parameters of a parallel electric hybrid bus drive train. Hybrid system parameters mainly include the power rating of internal combustion engine (ICE, gear ratios of transmission, power rating, and maximal torque of motor, power, and capacity of battery. The regenerative model is built in the vehicle model to estimate the regenerative energy in the real road conditions. The design target is to ensure that the vehicle meets the specified vehicle performance, such as speed and acceleration, and at the same time, operates the ICE within an expected speed range. Several pairs of parameters are selected from the result analysis, and the fuel saving result in the road test shows that a 25% reduction is achieved in fuel consumption.

Spatial analysis of bus transport networks using network theory

Science.gov (United States)

Shanmukhappa, Tanuja; Ho, Ivan Wang-Hei; Tse, Chi Kong

2018-07-01

In this paper, we analyze the bus transport network (BTN) structure considering the spatial embedding of the network for three cities, namely, Hong Kong (HK), London (LD), and Bengaluru (BL). We propose a novel approach called supernode graph structuring for modeling the bus transport network. A static demand estimation procedure is proposed to assign the node weights by considering the points of interests (POIs) and the population distribution in the city over various localized zones. In addition, the end-to-end delay is proposed as a parameter to measure the topological efficiency of the bus networks instead of the shortest distance measure used in previous works. With the aid of supernode graph representation, important network parameters are analyzed for the directed, weighted and geo-referenced bus transport networks. It is observed that the supernode concept has significant advantage in analyzing the inherent topological behavior. For instance, the scale-free and small-world behavior becomes evident with supernode representation as compared to conventional or regular graph representation for the Hong Kong network. Significant improvement in clustering, reduction in path length, and increase in centrality values are observed in all the three networks with supernode representation. The correlation between topologically central nodes and the geographically central nodes reveals the interesting fact that the proposed static demand estimation method for assigning node weights aids in better identifying the geographically significant nodes in the network. The impact of these geographically significant nodes on the local traffic behavior is demonstrated by simulation using the SUMO (Simulation of Urban Mobility) tool which is also supported by real-world empirical data, and our results indicate that the traffic speed around a particular bus stop can reach a jammed state from a free flow state due to the presence of these geographically important nodes. A comparison

A new MV bus transfer scheme for nuclear power plants

International Nuclear Information System (INIS)

Chang, C.K.

2015-01-01

The auxiliary power system of many generating stations consists of offsite power supply system and onsite power supply system, including emergency diesel generators (EDG) to provide secure power to auxiliary loads. If a normal power supply fails to supply power, then the power source is transferred to a standby power supply. In the case of nuclear power plants (NPP), the unit auxiliary transformer (UAT) and standby auxiliary transformer (SAT) - or station service transformer - are installed and powered from 2 offsite power circuits to meet regulatory requirements. The transfer methods of a motor bus from a normal source to a standby source used in power generating stations are fast bus transfer, in-phase transfer, or residual transfer. Fast bus transfer method is the most popular and residual voltage transfer method that is used as a backup in medium voltage buses in general. The use of the advanced technology like open circuit voltage prediction and digital signal processing algorithms can improve the reliability of fast transfer scheme. However, according to the survey results of the recent operation records in nuclear power plants, there were many instances where the fast transfer scheme has failed. To assure bus transfer in any conditions and circumstances, un-interruptible bus transfer scheme utilizing the state of the art medium voltage UPS (Un-interruptible Power Supply) is discussed and elaborated

[Injuries sustained by bus passengers in the municipality of Odense 1996-1999].

Science.gov (United States)

Barsi, T; Faergemann, C; Larsen, L B

2001-10-22

Owing to several recent bus-related accidents in Denmark, we wished to investigate injuries sustained by passengers. From our ongoing registration of patients treated in the casualty department at Odense University Hospital, we identified all residents of Odense Municipality who had sustained injuries as bus passengers from 1996 to 1999. Market analysis and demographic information were used to calculate the incidence and risk. Over this four-year period, 327 consecutive injuries had been sustained by 246 bus passengers, 72 men and 174 women, mean ages 44 and 53 years. The incidence rate was 3.3 injured per 10,000 inhabitants per year, with no increasing tendency during the study period. The risk was 2.2 injured per 1,000,000 bus passengers per year, highest in women and increasing with age. Injuries most frequently occurred when the bus stopped (31%), as passengers were boarding or alighting (23%), or during collision with another vehicle (20%). Most commonly injured areas were the lower (30%) and upper (28%) extremities and the head or neck (27%). Contusions and sprains were the most common injuries (59%). The most common fractures were those of the humerus and hip region. Bus passenger injuries are not a growing problem. The incidence increases with age.

Bus transport in Greater Manchester

DEFF Research Database (Denmark)

Sørensen, Claus Hedegaard; Gudmundsson, Henrik

component regards the organisation of public bus transport at the local level. This involves the deregulation and privatisation reforms introduced by the Conservative Government from 1986 onwards, as well as the ‘partnerships’ and other new instruments introduced by the Labour Government in the Transport...

Activities of four bus terminals of Semarang City gateway and the related GHG emission

Science.gov (United States)

Huboyo, H. S.; Wardhana, I. W.; Sutrisno, E.; Wangi, L. S.; Lina, R. A.

2018-01-01

The activities of the bus terminal, including loading-unloading passengers, bus idling, and bus movements at the terminal, will emit GHG’s emission. This research analyzes GHG emission from four terminals, i.e., Mangkang, Terboyo, Penggaron, and Sukun in Semarang City. The emission was estimated by observing detail activities of public transport means, especially for moving and idling time. The emission was calculated by Tier 2 method based on the vehicle type as well as fuel consumption. The highest CO2e during vehicle movements at Sukun area was contributed by large bus about 2.08 tons/year, while at Terboyo terminal was contributed by medium bus about 347.97 tons/year. At Mangkang terminals, the highest emission for vehicle movements was attributed by medium bus as well of about 53.18 tons/year. At last, Penggaron terminal’s highest GHG emission was attributed by BRT about 26.47 tons/year. During idling time, the highest contributor to CO2e was the large bus at the three terminals, i.e., Sukun of 43.53 tons/year, Terboyo of 196.56 tons/year, and Mangkang of 84.26 tons/year, while at Penggaron, BRT dominated with CO2e of 26.47 tons/year. The management of public transport in terminals is crucial to mitigate the emission related to bus terminals activities.

VHDL resolved function based inner communication bus for FPGA

Science.gov (United States)

Pozniak, Krzysztof T.

2017-08-01

This article discusses a method of building an internal, universal and parametric bus. The solution was designed for a variety of FPGA families and popular VHDL compilers. The algorithm of automatic configuration of address space and methods of receiving and sending addressed data are discussed. The basic solution realized in VHDL language in a behavioral form and chosen examples of practical use of the internal bus are presented in detail.

Passenger bus industry weather information application.

Science.gov (United States)

2011-03-21

Adverse weather significantly affects the United States national transportation system, including commercial companies : that rely on highways to support their enterprises. The Passenger Bus (Motorcoach) Industry (PBI) is one such affected : user who...

Spanish version of Bus Drivers' Job Demands Scale (BDJD-24).

Science.gov (United States)

Boada-Grau, Joan; Prizmic-Kuzmica, Aldo-Javier; González-Fernández, Marcos-David; Vigil-Colet, Andreu

2013-01-01

Karasek and Theorell's Job Demands-Control Model argues that adverse health-related outcomes, both psychological and physiological, arise from a combination of high job demand and a low level of job control. The objective was to adapt Meijman and Kompier's Bus Drivers' Job Demands Scale (BDJD-24), which enables us to assess the job demands of bus drivers, to Spanish. The final version of the Spanish adaptation was applied to a sample made up of 287 bus drivers living in Spain (80.1% men and 19.9% women), whose average age was 40.44 (SD= 11.78). The results yielded a three-factor structure for the scale used: Time Pressure, Safety, and Passengers. These findings confirm that the Spanish version replicates the factor structure of the original English scale. The reliability of the three subscales was acceptable, ranging from .75 to .84. Furthermore, the subscales were also related to different external correlates and to other scales and showed good convergent and criterion validity. The present instrument can be used to evaluate job demands of bus drivers, as its psychometrics are substantially sound.

Successfulness of bus rapid transit systems in Asia. Ex-post evaluation

NARCIS (Netherlands)

Kogdenko, Nadja

2010-01-01

SUMMARY Bus Rapid Transit (BRT) can be defined as “a bus-based mass transit system that delivers fast, comfortable, and cost-effective urban mobility”. It offers the opportunity to create a high-quality mass transit system at affordable costs, which is p

Rethinking passive transport: bus fare exemptions and young people's wellbeing.

Science.gov (United States)

Jones, Alasdair; Steinbach, Rebecca; Roberts, Helen; Goodman, Anna; Green, Judith

2012-05-01

Much recent public health research has emphasised the health impacts for young people of 'active travel' modes, typically defined as walking and cycling. Less research has focused on public transport modes. Drawing on qualitative data, we examine the links between bus travel and wellbeing in London, where young people currently have free bus travel. Our findings indicate that bus travel can be both a physically and socially active experience for young people. We suggest a more nuanced understanding of 'active travel' is now needed, alongside greater attention to urban public transport networks as key sites that impact on important determinants of wellbeing such as independent mobility and social inclusion. Copyright © 2012 Elsevier Ltd. All rights reserved.

Correlates of walking to school and implications for public policies: survey results from parents of elementary school children in Austin, Texas.

Science.gov (United States)

Zhu, Xuemei; Lee, Chanam

2009-01-01

Walking can be a healthy, sustainable, and equitable mode of transportation, but is not widely used for children's school travel. This study identifies multi-level correlates of walking to/from school and relevant policy implications. We surveyed parents/guardians of 2,695 students from 19 elementary schools in Austin, Texas, which featured diverse sociodemographic and environmental characteristics. Among the personal and social factors, negative correlates were parents' education, car ownership, personal barriers, and school bus availability; positive correlates were parents' and children's positive attitude and regular walking behavior, and supportive peer influences. Of physical environmental factors, the strongest negative correlates were distance and safety concerns, followed by the presence of highways/freeways, convenience stores, office buildings, and bus stops en route. Our findings suggest that society should give high priority to lower socioeconomic status populations and to multi-agency policy interventions that facilitate environmental changes, safety improvements, and educational programs targeting both parents and children.

A PRACTICAL STUDY ON APPLICABILITY OF THE INCENTIVE SUBSIDY TO BUS NETWORK IN KUMAMOTO CITY

Science.gov (United States)

Mizokami, Shoshi; Fujimi, Toshio; Hirano, Toshihiko

Recently, the number of passenger of public bus services in Japan tends to decrease due to the motorization. This condition leads to a severe management situation, including in Kumamoto City. Since 1984, the deficit of bus companies operation in provision of bus services in Kumamoto has been covered by Kumamoto City Government on the basis of lines subsidy, and the city allocated a number of subsidy of about 200 million yen in 2007. Currently, The Kumamoto city government plans to reduce the amount of subsidy to bus companies by introducing the giving of incentive to bus companies in order to trim bus company deficit. This study aims to construct the mathematical model of the incentive reward and apply the model to realignment of buses lines networks in Kumamoto Metropolitan Area.

Analyzing injury severity of bus passengers with different movements.

Science.gov (United States)

Li, Duo; Zhao, Yifei; Bai, Qiang; Zhou, Bei; Ling, Hongbiao

2017-07-04

Though public transport vehicles are rarely involved in mass casualty accidents, when they are, the number of injuries and fatalities is usually high due to the high passenger capacity. Of the few studies that have been conducted on bus safety, the majority focused on vehicle safety features, road environmental factors, as well as driver characteristics. Nevertheless, few studies have attempted to investigate the underlying risk factors related to bus occupants. This article presents an investigation aimed at identifying the risk factors affecting injury severity of bus passengers with different movements. Three different passenger movement types including standing, seated, and boarding/alighting were analyzed individually using classification and regression tree (CART) method based on publicly available accident database of Great Britain. According to the results of exploratory analyses, passenger age and vehicle maneuver are associated with passenger injury severity in all 3 types of accidents. Moreover, the variable "skidding and overturning" is associated with injury severity of seated passengers and driver age is correlated with injury severity of standing and boarding/alighting passengers. The CART method shows its ability to identify and easily explain the complicated patterns affecting passenger injury severity. Several countermeasures to reduce bus passenger injury severity are recommended.

Ride Quality Assessment of Bus Suspension System through Modal Frequency Response Approach

Directory of Open Access Journals (Sweden)

Y. S. Kong

2014-09-01

Full Text Available The ride dynamic characteristics of an urban bus were investigated through simulations with suspension component characteristics and were validated through field measurements. It was performed on highway road at a constant forward speed. A random vibration bus model with two parallel tracks of terrain profile was synthesized with superposition between the left and right sides as well as time delay between front and rear. The bus frequency response model was introduced with embedded modal extraction data to enhance computation efficiency. The simulation results of the bus model were derived in terms of acceleration PSD and frequency-weighted root mean square acceleration along the vertical axes at three locations, namely, driver side, middle, and rear passenger side, to obtain the overall bus ride performance. Another two sets of new leaf spring design were proposed as suspension parameter analysis. The simulation approach provides reasonably good results in evaluating passenger perception on ride and shows that the proposed new spring design can significantly improve the ride quality of the driver and passengers.

Recognizing driving in haste

NARCIS (Netherlands)

Rendón-Vélez, E.

2014-01-01

One can often hear people discussing the reasons why a road accident has happened: “She had to pick up her kids in the school before four o’clock and she was driving in haste and careless”, “He was stressed, he wanted to reach the beginning of the football match, tried to drive faster and didn't

Massachusetts Fuel Cell Bus Project: Demonstrating a Total Transit Solution for Fuel Cell Electric Buses in Boston

Energy Technology Data Exchange (ETDEWEB)

2017-05-22

The Federal Transit Administration's National Fuel Cell Bus Program focuses on developing commercially viable fuel cell bus technologies. Nuvera is leading the Massachusetts Fuel Cell Bus project to demonstrate a complete transit solution for fuel cell electric buses that includes one bus and an on-site hydrogen generation station for the Massachusetts Bay Transportation Authority (MBTA). A team consisting of ElDorado National, BAE Systems, and Ballard Power Systems built the fuel cell electric bus, and Nuvera is providing its PowerTap on-site hydrogen generator to provide fuel for the bus.

Best Operational and Maintenance Practices for City Bus Fleets to Maximize Fuel Economy

OpenAIRE

Energy Sector Management Assistance Program

2011-01-01

In most large cities in developing countries, buses continue to be the public transport option of choice, carrying a large share of urban travelers. However, transit bus companies in these countries are often cash-strapped. In many cases, the operating cost per bus kilometer exceeds revenues and bus fares are often kept low irrespective of the cost of providing service. Many cities are dom...

Focus on Energy: A School Transportation Handbook. Proceedings of the Midwest School Transportation Fleet Management Seminar (Lansing, Michigan, November 28-29, 1979).

Science.gov (United States)

Michigan State Dept. of Commerce, Lansing.

Presented are proceedings and supplementary reports of the Midwest School Transportation Fleet Management Seminar, which was held in Lansing, Michigan, November 28-29, 1979. Among the school bus energy management topics discussed are energy feasibility studies, the use of programmed information systems, energy conservation strategies, and…

Determinants of spikes in ultrafine particle concentration whilst commuting by bus

Science.gov (United States)

Lim, Shanon; Dirks, Kim N.; Salmond, Jennifer A.; Xie, Shanju

2015-07-01

This paper examines concentration of ultrafine particles (UFPs) based on data collected using high-resolution UFP monitors whilst travelling by bus during rush hour along three different urban routes in Auckland, New Zealand. The factors influencing in-bus UFP concentration were assessed using a combination of spatial, statistical and GIS analysis techniques to determine both spatial and temporal variability. Results from 68 bus trips showed that concentrations varied more within a route than between on a given day, despite differences in urban morphology, land use and traffic densities between routes. A number of trips were characterised by periods of very rapid increases in UFPs (concentration 'spikes'), followed by slow declines. Trips which recorded at least one spike (an increase of greater than 10,000 pt/cm3) resulted in significantly higher mean concentrations. Spikes in UFPs were significantly more likely to occur when travelling at low speeds and when passengers were alighting and boarding at bus stops close to traffic light intersections.

Determinants of exposure to fine particulate matter (PM 2.5) for waiting passengers at bus stops

Science.gov (United States)

Hess, Daniel Baldwin; Ray, Paul David; Stinson, Anne E.; Park, JiYoung

2010-12-01

This research evaluates commuter exposure to particulate matter during pre-journey commute segments for passengers waiting at bus stops by investigating 840 min of simultaneous exposure levels, both inside and outside seven bus shelters in Buffalo, New York. A multivariate regression model is used to estimate the relation between exposure to particulate matter (PM 2.5 measured in μg m -3) and three vectors of determinants: time and location, physical setting and placement, and environmental factors. Four determinants have a statistically significant effect on particulate matter: time of day, passengers' waiting location, land use near the bus shelter, and the presence of cigarette smoking at the bus shelter. Model results suggest that exposure to PM 2.5 inside a bus shelter is 2.63 μg m -3 (or 18 percent) higher than exposure outside a bus shelter, perhaps due in part to the presence of cigarette smoking. Morning exposure levels are 6.51 μg m -3 (or 52 percent) higher than afternoon levels. Placement of bus stops can affect exposure to particulate matter for those waiting inside and outside of shelters: air samples at bus shelters located in building canyons have higher particulate matter than bus shelters located near open space.

RS-485 Bus Design of a Missile Simulation Training System

Directory of Open Access Journals (Sweden)

Liu Fang

2013-07-01

Full Text Available In a missile simulation training system with one-master and multi-slaves distributed system structure, a universal controller is necessary due to the system composed with several controllers. In this research, the designed controllers communicate with each other and upper control computer through RS-485 field bus. RS-485 bus including interface circuits, transmission protocol, Cyclic Redundancy Check (CRC method and upper control test software is designed and proposed. The universal controller adopting the designed RS-485 interface circuits is connected through twisted-pair and makes the simulation system, then the controller is tested in line. The results show that the RS-485 bus communicates effectively using the protocol and CRC method, data transmission rates reaches 115.2 kbps, and has a good stability.

Driving Privileges Facilitate Impaired Driving in Those Youths Who Use Alcohol or Marijuana

Science.gov (United States)

Lewis, Todd F.; Scott Olds, R.; Thombs, Dennis L.; Ding, Kele

2009-01-01

The aim of this study was to determine whether possession of a driver's license increases the risk of impaired driving among adolescents who use alcohol or marijuana. An anonymous questionnaire was administered to secondary school students in northeast Ohio across multiple school districts. Logistic regression analyses revealed that after…

A Study of BUS Architecture Design for Controller of Nuclear Power Plant Using FPGA

Energy Technology Data Exchange (ETDEWEB)

Lee, Dongil; Yun, Donghwa; Hwang, Sungjae; Kim, Myeongyun; Lee, Dongyun [PONUTech Co. Ltd., Seoul (Korea, Republic of)

2014-05-15

CPU (Central Processing Unit) operating speed and communication rate have been more technically improved than before. However, whole system is been a degradation of performance by electronic and structural limitation of parallel bus. Transmission quantity and speed have a limit and need arbiter in order to do arbitration because several boards shared parallel bus. Arbiter is a high complexity in implementing so it increases component per chip. If a parallel bus uses, it will occurs some problems what are reflection noise, power/ground noise (or ground bounce) as SSN (Simultaneous Switching Noise) and crosstalk noise like magnetic coupling. In this paper, in order to solve a problem of parallel bus in controller of NPP (Nuclear Power Plant), proposes the bus architecture design using FPGA (Field Programmable Gate Array) based on LVDS (Low Voltage Differential Signaling)

A Study of BUS Architecture Design for Controller of Nuclear Power Plant Using FPGA

International Nuclear Information System (INIS)

Lee, Dongil; Yun, Donghwa; Hwang, Sungjae; Kim, Myeongyun; Lee, Dongyun

2014-01-01

CPU (Central Processing Unit) operating speed and communication rate have been more technically improved than before. However, whole system is been a degradation of performance by electronic and structural limitation of parallel bus. Transmission quantity and speed have a limit and need arbiter in order to do arbitration because several boards shared parallel bus. Arbiter is a high complexity in implementing so it increases component per chip. If a parallel bus uses, it will occurs some problems what are reflection noise, power/ground noise (or ground bounce) as SSN (Simultaneous Switching Noise) and crosstalk noise like magnetic coupling. In this paper, in order to solve a problem of parallel bus in controller of NPP (Nuclear Power Plant), proposes the bus architecture design using FPGA (Field Programmable Gate Array) based on LVDS (Low Voltage Differential Signaling)

Mars Comm/Nav MicroSat Network Using the Multi-Mission Bus Launched Piggyback by Ariane 5

Science.gov (United States)

Hastrup, R. C.; Cesarone, R. J.; Morabito, D. D.

1999-01-01

-mission spacecraft bus are described with discussion of the mission-system tradeoffs for the driving requirements. The functional design of the in-situ communications / navigation package, which constitutes the payload of the microsat, is also described. The paper also includes discussion of technologies which are of specific importance to the implementation of the comm/nav microsat network.

Regenerative Braking System for Series Hybrid Electric City Bus

OpenAIRE

Zhang, Junzhi; Lu, Xin; Xue, Junliang; Li, Bos

2008-01-01

Regenerative Braking Systems (RBS) provide an efficient method to assist hybrid electric buses achieve better fuel economy while lowering exhaust emissions. This paper describes the design and testing of three regenerative braking systems, one of which is a series regenerative braking system and two of which are parallel regenerative braking systems. The existing friction based Adjustable Braking System (ABS) on the bus is integrated with each of the new braking systems in order to ensure bus...

A descriptive study on public transport user behaviour from Live Bus Arrivals

OpenAIRE

Dell’Amico, M.; Hadjidimitriou, S.; Kaparias, I.

2014-01-01

In order to offer public transport that meet citizens’ needs for transport and further increase the use of bus services, Public Authorities need to analyse and understand travellers behaviour. Automatic Vehicle Location (AVL) data provide information on the observed time of arrival and departure of a bus at each stop. These data are fed into an algorithm to provide information to users on the expected time of arrival at the bus stop by an on-line service. In the city of London this service is...

Understanding & modeling bus transit driver availability.

Science.gov (United States)

2014-07-01

Bus transit agencies are required to hire extraboard (i.e. back-up) operators to account for unexpected absences. Incorrect sizing of extra driver workforce is problematic for a number of reasons. Overestimating the appropriate number of extraboard o...

Landscape heritage objects' effect on driving: a combined driving simulator and questionnaire study.

Science.gov (United States)

Antonson, Hans; Ahlström, Christer; Mårdh, Selina; Blomqvist, Göran; Wiklund, Mats

2014-01-01

According to the literature, landscape (panoramas, heritage objects e.g. landmarks) affects people in various ways. Data are primarily developed by asking people (interviews, photo sessions, focus groups) about their preferences, but to a lesser degree by measuring how the body reacts to such objects. Personal experience while driving a car through a landscape is even more rare. In this paper we study how different types of objects in the landscape affect drivers during their drive. A high-fidelity moving-base driving simulator was used to measure choice of speed and lateral position in combination with stress (heart rate measure) and eye tracking. The data were supplemented with questionnaires. Eighteen test drivers (8 men and 10 women) with a mean age of 37 were recruited. The test drivers were exposed to different new and old types of landscape objects such as 19th century church, wind turbine, 17th century milestone and bus stop, placed at different distances from the road driven. The findings are in some respect contradictory, but it was concluded that that 33% of the test drivers felt stressed during the drive. All test drivers said that they had felt calm at times during the drive but the reason for this was only to a minor degree connected with old and modern objects. The open landscape was experienced as conducive to acceleration. Most objects were, to a small degree, experienced (subjective data) as having a speed-reducing effect, much in line with the simulator data (objective data). Objects close to the road affected the drivers' choice of' lateral position. No significant differences could be observed concerning the test drivers' gaze between old or modern objects, but a significant difference was observed between the test drivers' gaze between road stretches with faraway objects and stretches without objects. No meaningful, significant differences were found for the drivers' stress levels as measured by heart rate. Copyright © 2013 Elsevier Ltd. All

Exploring public bus service quality in South Africa: A structural equation modelling approach

Directory of Open Access Journals (Sweden)

Ayanda M. Vilakazi

2014-07-01

Full Text Available This study, which is a deviation from the usual practice of using SERVQUAL or an adaptedversion thereof, uses McKnight, Pagano and Paaswell’s (1986 service quality dimensions,namely reliability; extent of service; comfort; safety; and affordability (RECSA and structuralequation modelling to determine commuters’ perception of public bus service quality in amajor city in South Africa. The RECSA model was adapted and fitted to the data collectedfrom a convenience sample of bus commuters in Johannesburg, using structural equationmodelling. It was ascertained that reliability, service, comfort and safety influenced thepublic bus commuters’ perception of the overall service quality. The implications of theaforementioned findings for providers of public bus services are explained.

SEDS MIL-STD-1773 fiber optic data bus: Proton irradiation test results and spaceflight SEU data

Energy Technology Data Exchange (ETDEWEB)

LaBel, K.A.; Stassinopoulos, E.G.; Miller, J.T. (NASA/GSFC, Greenbelt, MD (United States)); Marshall, P. (NRL/SFA, Washington, DC (United States)); Dale, C. (NRL, Washington, DC (United States)); Crabtree, C.M. (Hughes/ST Systems Corp., Seabrook, MD (United States)); Gates, M.M. (Jackson and Tull, Seabrook, MD (United States))

1993-12-01

The Small Explorer Data System (SEDS) was launched in July of 1992 as part of the Solar Anomalous Magnetospheric Particle Explorer (SAMPEX) mission. The SEDS utilizes NASA's first MIL-STD-1773 Fiber Optic Multiplexed Data Bus (or 1773 bus) to communicate with other spacecraft subsystems in the space environment. The 1773 bus is the fiber optic version of the MIL-STD-1553 Data Bus, a electronic wire bus used in many avionics applications. The authors present proton test and space flight single event effect data for NASA's first fiber optic data bus. Bit error rate predictions based on a new proton direct ionization model agree well with flight data for proton belt and solar flare effects.

A comparison of core degradation phenomena in the CORA, QUENCH, Phébus SFD and Phébus FP experiments

Energy Technology Data Exchange (ETDEWEB)

Haste, T., E-mail: tim.haste@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire, IRSN, BP 3, F-13115 St. Paul-lez-Durance Cedex (France); Steinbrück, M., E-mail: martin.steinbrueck@kit.edu [Karlsruhe Institute of Technology (KIT), Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany); Barrachin, M., E-mail: marc.barrachin@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire, IRSN, BP 3, F-13115 St. Paul-lez-Durance Cedex (France); Luze, O. de, E-mail: olivier.de-luze@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire, IRSN, BP 3, F-13115 St. Paul-lez-Durance Cedex (France); Grosse, M., E-mail: mirco.grosse@kit.edu [Karlsruhe Institute of Technology (KIT), Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany); Stuckert, J., E-mail: juri.stuckert@kit.edu [Karlsruhe Institute of Technology (KIT), Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany)

2015-03-15

Highlights: • The results of the experiments CORA, QUENCH and Phébus SFD/FP are summarised. • All phenomena expected up to melt movement to the lower head are shown consistently. • Separate-effect tests performed at KIT and IRSN aid improve their modelling. • Data from the integral tests help independent validation of new and improved models. • The improved codes will help reduce uncertainties in safety-critical areas for core degradation. - Abstract: Over the past 20 years, integral fuel bundle experiments performed at IRSN Cadarache, France (Phébus-SFD and Phébus FP – fission heated) and at Karlsruhe Institute of Technology, Germany (CORA and QUENCH – electrically heated), accompanied by separate-effect tests, have provided a wealth of detailed information on core degradation phenomena that occur under severe accident conditions, relevant to such safety issues as in-vessel retention of the core, recovery of the core by water reflood, hydrogen generation and fission product release. These data form an important basis for development and validation of severe accident analysis codes such as ASTEC (IRSN/GRS, EC) and MELCOR (USNRC/SNL, USA) that are used to assess the safety of current and future reactor designs, so helping to reduce the uncertainty associated with such code predictions. Following the recent end of the Phébus FP project, it is appropriate now to compare the core degradation phenomena observed in these four major experimental series, indicating the main conclusions that have been drawn. This covers subjects such as early phase degradation up to loss of rod-like geometry (all the series), late phase degradation and the link between fission product release and core degradation (Phébus FP), oxidation phenomena (all the series), reflood behaviour (CORA and QUENCH), as well as particular topics such as the effects of control rod material and fuel burn-up on core degradation. It also outlines the separate-effects experiments performed to

Saturday Driving Restrictions Fail to Improve Air Quality in Mexico City

Science.gov (United States)

Davis, Lucas W.

2017-02-01

Policymakers around the world are turning to license-plate based driving restrictions in an effort to address urban air pollution. The format differs across cities, but most programs restrict driving once or twice a week during weekdays. This paper focuses on Mexico City, home to one of the oldest and best-known driving restriction policies. For almost two decades Mexico City’s driving restrictions applied during weekdays only. This changed recently, however, when the program was expanded to include Saturdays. This paper uses hourly data from pollution monitoring stations to measure the effect of the Saturday expansion on air quality. Overall, there is little evidence that the program expansion improved air quality. Across eight major pollutants, the program expansion had virtually no discernible effect on pollution levels. These disappointing results stand in sharp contrast to estimates made before the expansion which predicted a 15%+ decrease in vehicle emissions on Saturdays. To understand why the program has been less effective than expected, the paper then turns to evidence from subway, bus, and light rail ridership, finding no evidence that the expansion was successful in getting drivers to switch to lower-emitting forms of transportation.

Analysis, operation and maintenance of a fuel cell/battery series-hybrid bus for urban transit applications

Science.gov (United States)

Bubna, Piyush; Brunner, Doug; Gangloff, John J.; Advani, Suresh G.; Prasad, Ajay K.

The fuel cell hybrid bus (FCHB) program was initiated at the University of Delaware in 2005 to demonstrate the viability of fuel cell vehicles for transit applications and to conduct research and development to facilitate the path towards their eventual commercialization. Unlike other fuel cell bus programs, the University of Delaware's FCHB design features a battery-heavy hybrid which offers multiple advantages in terms of cost, performance and durability. The current fuel cell hybrid bus is driven on a regular transit route at the University of Delaware. The paper describes the baseline specifications of the bus with a focus on the fuel cell and the balance of plant. The fuel cell/battery series-hybrid design is well suited for urban transit routes and provides key operational advantages such as hydrogen fuel economy, efficient use of the fuel cell for battery recharging, and regenerative braking. The bus is equipped with a variety of sensors including a custom-designed cell voltage monitoring system which provide a good understanding of bus performance under normal operation. Real-time data collection and analysis have yielded key insights for fuel cell bus design optimization. Results presented here illustrate the complex flow of energy within the various subsystems of the fuel cell hybrid bus. A description of maintenance events has been included to highlight the issues that arise during general operation. The paper also describes several modifications that will facilitate design improvements in future versions of the bus. Overall, the fuel cell hybrid bus demonstrates the viability of fuel cells for urban transit applications in real world conditions.

Traveling by Bus Instead of Car on Urban Major Roads: Safety Benefits for Vehicle Occupants, Pedestrians, and Cyclists.

Science.gov (United States)

Morency, Patrick; Strauss, Jillian; Pépin, Félix; Tessier, François; Grondines, Jocelyn

2018-04-01

Some studies have estimated fatality and injury rates for bus occupants, but data was aggregated at the country level and made no distinction between bus types. Also, injured pedestrians and cyclists, as a result of bus travel, were overlooked. We compared injury rates for car and city bus occupants on specific urban major roads, as well as the cyclist and pedestrian injuries associated with car and bus travel. We selected ten bus routes along major urban arterials (in Montreal, Canada). Passenger-kilometers traveled were estimated from vehicle counts at intersections (2002-2010) and from bus passenger counts (2008). Police accident reports (2001-2010) provided injury data for all modes. Injury rates associated with car and bus travel were calculated for vehicle occupants, pedestrians, and cyclists. Injury rate ratios were also computed. The safety benefits of bus travel, defined as the number of vehicle occupant, cyclist, and pedestrian injuries saved, were estimated for each route. Overall, for all ten routes, the ratio between car and bus occupant injury rates is 3.7 (95% CI [3.4, 4.0]). The rates of pedestrian and cyclist injuries per hundred million passenger-kilometers are also significantly greater for car travel than that for bus travel: 4.1 (95% CI [3.5, 4.9]) times greater for pedestrian injuries; 5.3 (95% CI [3.8, 7.6]) times greater for cyclist injuries. Similar results were observed for fatally and severely injured vehicle occupants, cyclists, and pedestrians. At the route level, the safety benefits of bus travel increase with the difference in injury rate associated with car and bus travel but also with the amount of passenger-kilometers by bus. Results show that city bus is a safer mode than car, for vehicle occupants but also for cyclists and pedestrians traveling along these bus routes. The safety benefits of bus travel greatly vary across urban routes; this spatial variation is most likely linked to environmental factors. Understanding the

Real life testing of a Hybrid PEM Fuel Cell Bus

Science.gov (United States)

Folkesson, Anders; Andersson, Christian; Alvfors, Per; Alaküla, Mats; Overgaard, Lars

Fuel cells produce low quantities of local emissions, if any, and are therefore one of the most promising alternatives to internal combustion engines as the main power source in future vehicles. It is likely that urban buses will be among the first commercial applications for fuel cells in vehicles. This is due to the fact that urban buses are highly visible for the public, they contribute significantly to air pollution in urban areas, they have small limitations in weight and volume and fuelling is handled via a centralised infrastructure. Results and experiences from real life measurements of energy flows in a Scania Hybrid PEM Fuel Cell Concept Bus are presented in this paper. The tests consist of measurements during several standard duty cycles. The efficiency of the fuel cell system and of the complete vehicle are presented and discussed. The net efficiency of the fuel cell system was approximately 40% and the fuel consumption of the concept bus is between 42 and 48% lower compared to a standard Scania bus. Energy recovery by regenerative braking saves up 28% energy. Bus subsystems such as the pneumatic system for door opening, suspension and brakes, the hydraulic power steering, the 24 V grid, the water pump and the cooling fans consume approximately 7% of the energy in the fuel input or 17% of the net power output from the fuel cell system. The bus was built by a number of companies in a project partly financed by the European Commission's Joule programme. The comprehensive testing is partly financed by the Swedish programme "Den Gröna Bilen" (The Green Car). A 50 kW el fuel cell system is the power source and a high voltage battery pack works as an energy buffer and power booster. The fuel, compressed hydrogen, is stored in two high-pressure stainless steel vessels mounted on the roof of the bus. The bus has a series hybrid electric driveline with wheel hub motors with a maximum power of 100 kW. Hybrid Fuel Cell Buses have a big potential, but there are

Replacement model of city bus: A dynamic programming approach

Science.gov (United States)

Arifin, Dadang; Yusuf, Edhi

2017-06-01

This paper aims to develop a replacement model of city bus vehicles operated in Bandung City. This study is driven from real cases encountered by the Damri Company in the efforts to improve services to the public. The replacement model propounds two policy alternatives: First, to maintain or keep the vehicles, and second is to replace them with new ones taking into account operating costs, revenue, salvage value, and acquisition cost of a new vehicle. A deterministic dynamic programming approach is used to solve the model. The optimization process was heuristically executed using empirical data of Perum Damri. The output of the model is to determine the replacement schedule and the best policy if the vehicle has passed the economic life. Based on the results, the technical life of the bus is approximately 20 years old, while the economic life is an average of 9 (nine) years. It means that after the bus is operated for 9 (nine) years, managers should consider the policy of rejuvenation.

Study on the optimum design of bus window pillar join40t; Bus window pillar ketsugo buzai no saiteki sekkei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tomioka, N [Nihon University, Tokyo (Japan); Lim, S; Kim, M; Lee, H; Kang, S; Bae, D

1997-10-01

Automobile body structure is generally assembled using various spot welded box sectional members. Especially, in the case of the bus, the shape of window pillar joint is assembled m T-type. This T-type member has some problem such as high stress concentration, low fatigue strength and structural rigidity. Therefore, in this report, performed a study on the optimum design of the bus window pillar joint for such problem by FEM analysis and experiments. 1 ref., 10 figs., 2 tabs.

Redesign of Transjakarta Bus Driver's Cabin

Science.gov (United States)

Mardi Safitri, Dian; Azmi, Nora; Singh, Gurbinder; Astuti, Pudji

2016-02-01

Ergonomic risk at work stations with type Seated Work Control was one of the problems faced by Transjakarta bus driver. Currently “Trisakti” type bus, one type of bus that is used by Transjakarta in corridor 9, serving route Pinang Ranti - Pluit, gained many complaints from drivers. From the results of Nordic Body Map questionnaires given to 30 drivers, it was known that drivers feel pain in the neck, arms, hips, and buttocks. Allegedly this was due to the seat position and the button/panel bus has a considerable distance range (1 meter) to be achieved by drivers. In addition, preliminary results of the questionnaire using Workstation Checklist identified their complaints about uncomfortable cushion, driver's seat backrest, and the exact position of the AC is above the driver head. To reduce the risk level of ergonomics, then did research to design the cabin by using a generic approach to designing products. The risk analysis driver posture before the design was done by using Rapid Upper Limb Assessment (RULA), Rapid Entire Body Assessment (REBA), and Quick Exposure Checklist (QEC), while the calculation of the moment the body is done by using software Mannequin Pro V10.2. Furthermore, the design of generic products was done through the stages: need metric-matrix, house of quality, anthropometric data collection, classification tree concept, concept screening, scoring concept, design and manufacture of products in the form of two-dimensional. While the design after design risk analysis driver posture was done by using RULA, REBA, and calculation of moments body as well as the design visualized using software 3DMax. From the results of analysis before the draft design improvements cabin RULA obtained scores of 6, REBA 9, and the result amounted to 57.38% QEC and moment forces on the back is 247.3 LbF.inch and on the right hip is 72.9 LbF.in. While the results of the proposed improvements cabin design RULA obtained scores of 3, REBA 4, and the moment of force on

Repeater For A Digital-Communication Bus

Science.gov (United States)

Torres-Guzman, Esteban; Olson, Stephen; Heaps, Tim

1993-01-01

Digital repeater circuit designed to extend range of communication on MIL-STD-1553 bus beyond original maximum allowable length of 300 ft. Circuit provides two-way communication, one way at time, and conforms to specifications of MIL-STD-1553. Crosstalk and instability eliminated.

Bus Travel Time Deviation Analysis Using Automatic Vehicle Location Data and Structural Equation Modeling

Directory of Open Access Journals (Sweden)

Xiaolin Gong

2015-01-01

Full Text Available To investigate the influences of causes of unreliability and bus schedule recovery phenomenon on microscopic segment-level travel time variance, this study adopts Structural Equation Modeling (SEM to specify, estimate, and measure the theoretical proposed models. The SEM model establishes and verifies hypotheses for interrelationships among travel time deviations, departure delays, segment lengths, dwell times, and number of traffic signals and access connections. The finally accepted model demonstrates excellent fitness. Most of the hypotheses are supported by the sample dataset from bus Automatic Vehicle Location system. The SEM model confirms the bus schedule recovery phenomenon. The departure delays at bus terminals and upstream travel time deviations indeed have negative impacts on travel time fluctuation of buses en route. Meanwhile, the segment length directly and negatively impacts travel time variability and inversely positively contributes to the schedule recovery process; this exogenous variable also indirectly and positively influences travel times through the existence of signalized intersections and access connections. This study offers a rational approach to analyzing travel time deviation feature. The SEM model structure and estimation results facilitate the understanding of bus service performance characteristics and provide several implications for bus service planning, management, and operation.

Middle School Program and Participatory Planning Drive School Design.

Science.gov (United States)

Sullivan, Kevin

1996-01-01

Uses the example of award-winning Black Hawk Middle School in Minnesota to examine: (1) developing a middle school architecture; (2) benefits of the house concept; (3) the need for staff involvement in school design; (4) assembling houses into schools; (5) reduced discipline problems; (6) fostering teacher collaboration; and (7) measuring success.…

Quantum bus of metal nanoring with surface plasmon polaritons

International Nuclear Information System (INIS)

Lin Zhirong; Guo Guoping; Tu Tao; Li Haiou; Zou Changling; Ren Xifeng; Guo Guangcan; Chen Junxue; Lu Yonghua

2010-01-01

We develop an architecture for distributed quantum computation using quantum bus of plasmonic circuits and spin qubits in self-assembled quantum dots. Deterministic quantum gates between two distant spin qubits can be reached by using an adiabatic approach in which quantum dots couple with highly detuned plasmon modes in a metallic nanoring. Plasmonic quantum bus offers a robust and scalable platform for quantum optics experiments and the development of on-chip quantum networks composed of various quantum nodes, such as quantum dots, molecules, and nanoparticles.

Overview of Multi-DC-Bus Solutions for DC Microgrids

DEFF Research Database (Denmark)

Ricchiuto, D.; Mastromauro, R.A.; Liserre, Marco

2013-01-01

DC Microgrids have recently received a lot of attention in the last years due to high penetration of renewable energy sources as well as distributed energy storage systems. In the future DC microgrids could be preferable respect to AC microgrids in terms of redundancy since multi-DC-Bus solutions...... could provide a continuative power supply to the loads. An overview of Multi-DC-Bus solutions is presented in this paper. The performances are compared on the basis of possible DC microgrid configurations, redundancy, different DC voltage levels....

Analysis, operation and maintenance of a fuel cell/battery series-hybrid bus for urban transit applications

Energy Technology Data Exchange (ETDEWEB)

Bubna, Piyush; Brunner, Doug; Gangloff, John J. Jr.; Advani, Suresh G.; Prasad, Ajay K. (Center for Fuel Cell Research, Department of Mechanical Engineering, University of Delaware, Newark, DE 19716 United States)

2010-06-15

The fuel cell hybrid bus (FCHB) program was initiated at the University of Delaware in 2005 to demonstrate the viability of fuel cell vehicles for transit applications and to conduct research and development to facilitate the path towards their eventual commercialization. Unlike other fuel cell bus programs, the University of Delaware's FCHB design features a battery-heavy hybrid which offers multiple advantages in terms of cost, performance and durability. The current fuel cell hybrid bus is driven on a regular transit route at the University of Delaware. The paper describes the baseline specifications of the bus with a focus on the fuel cell and the balance of plant. The fuel cell/battery series-hybrid design is well suited for urban transit routes and provides key operational advantages such as hydrogen fuel economy, efficient use of the fuel cell for battery recharging, and regenerative braking. The bus is equipped with a variety of sensors including a custom-designed cell voltage monitoring system which provide a good understanding of bus performance under normal operation. Real-time data collection and analysis have yielded key insights for fuel cell bus design optimization. Results presented here illustrate the complex flow of energy within the various subsystems of the fuel cell hybrid bus. A description of maintenance events has been included to highlight the issues that arise during general operation. The paper also describes several modifications that will facilitate design improvements in future versions of the bus. Overall, the fuel cell hybrid bus demonstrates the viability of fuel cells for urban transit applications in real world conditions. (author)

Understanding the knowledge and attitudes of commercial drivers in Ghana regarding alcohol impaired driving

Science.gov (United States)

Asiamah, G; Mock, C; Blantari, J

2002-01-01

Objectives: The knowledge and attitudes of commercial drivers in Ghana as regards alcohol impaired driving were investigated. This was done in order to provide information that could subsequently be used to develop antidrunk driving social marketing messages built upon the intrinsic values and motivation of these drivers. Methods: Focus group discussions were held with 43 bus and minibus drivers in the capital city, Accra. A structured discussion guide was used to capture information related to values, risk perceptions, leisure time activities, and attitudes on alcohol impaired driving. Results: The majority of drivers expressed an understanding that drunk driving was a significant risk factor for crashes. There was a significant under-appreciation of the extent of the problem, however. Most believed that it was only rare, extremely intoxicated drivers who were the problem. The drivers also had a minimal understanding of the concept of blood alcohol concentration and related legal limits. Despite these factors, there was widespread support for increased enforcement of existing antidrunk driving laws. Conclusions: In Ghana, commercial drivers understand the basic danger of drunk driving and are motivated to assist in antidrunk driving measures. There are misconceptions and deficits in knowledge that need to be addressed in subsequent educational campaigns. PMID:11928975

An interconnecting bus power optimization method combining interconnect wire spacing with wire ordering

International Nuclear Information System (INIS)

Zhu Zhang-Ming; Hao Bao-Tian; En Yun-Fei; Yang Yin-Tang; Li Yue-Jin

2011-01-01

On-chip interconnect buses consume tens of percents of dynamic power in a nanometer scale integrated circuit and they will consume more power with the rapid scaling down of technology size and continuously rising clock frequency, therefore it is meaningful to lower the interconnecting bus power in design. In this paper, a simple yet accurate interconnect parasitic capacitance model is presented first and then, based on this model, a novel interconnecting bus optimization method is proposed. Wire spacing is a process for spacing wires for minimum dynamic power, while wire ordering is a process that searches for wire orders that maximally enhance it. The method, i.e., combining wire spacing with wire ordering, focuses on bus dynamic power optimization with a consideration of bus performance requirements. The optimization method is verified based on various nanometer technology parameters, showing that with 50% slack of routing space, 25.71% and 32.65% of power can be saved on average by the proposed optimization method for a global bus and an intermediate bus, respectively, under a 65-nm technology node, compared with 21.78% and 27.68% of power saved on average by uniform spacing technology. The proposed method is especially suitable for computer-aided design of nanometer scale on-chip buses. (interdisciplinary physics and related areas of science and technology)

Safety evaluation of a hydrogen fueled transit bus

Energy Technology Data Exchange (ETDEWEB)

Coutts, D.A.; Thomas, J.K.; Hovis, G.L.; Wu, T.T. [Westinghouse Savannah River Co., Aiken, SC (United States)

1997-12-31

Hydrogen fueled vehicle demonstration projects must satisfy management and regulator safety expectations. This is often accomplished using hazard and safety analyses. Such an analysis has been completed to evaluate the safety of the H2Fuel bus to be operated in Augusta, Georgia. The evaluation methods and criteria used reflect the Department of Energy`s graded approach for qualifying and documenting nuclear and chemical facility safety. The work focused on the storage and distribution of hydrogen as the bus motor fuel with emphases on the technical and operational aspects of using metal hydride beds to store hydrogen. The safety evaluation demonstrated that the operation of the H2Fuel bus represents a moderate risk. This is the same risk level determined for operation of conventionally powered transit buses in the United States. By the same criteria, private passenger automobile travel in the United States is considered a high risk. The evaluation also identified several design and operational modifications that resulted in improved safety, operability, and reliability. The hazard assessment methodology used in this project has widespread applicability to other innovative operations and systems, and the techniques can serve as a template for other similar projects.

Technology Validation: Fuel Cell Bus Evaluations

Energy Technology Data Exchange (ETDEWEB)

Eudy, Leslie [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2018-01-02

This presentation describing the FY 2016 accomplishments for the National Renewable Energy Laboratory's Fuel Cell Bus Evaluations project was presented at the U.S. Department of Energy Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Meeting, June 7, 2016.

Testing of Environmental Satellite Bus-Instrument Interfaces Using Engineering Models

Science.gov (United States)

Gagnier, Donald; Hayner, Rick; Nosek, Thomas; Roza, Michael; Hendershot, James E.; Razzaghi, Andrea I.

2004-01-01

This paper discusses the formulation and execution of a laboratory test of the electrical interfaces between multiple atmospheric scientific instruments and the spacecraft bus that carries them. The testing, performed in 2002, used engineering models of the instruments and the Aura spacecraft bus electronics. Aura is one of NASA s Earth Observatory System missions. The test was designed to evaluate the complex interfaces in the command and data handling subsystems prior to integration of the complete flight instruments on the spacecraft. A problem discovered during the flight integration phase of the observatory can cause significant cost and schedule impacts. The tests successfully revealed problems and led to their resolution before the full-up integration phase, saving significant cost and schedule. This approach could be beneficial for future environmental satellite programs involving the integration of multiple, complex scientific instruments onto a spacecraft bus.

Increasing throughput of multiplexed electrical bus in pipe-lined architecture

Science.gov (United States)

Asaad, Sameh; Brezzo, Bernard V; Kapur, Mohit

2014-05-27

Techniques are disclosed for increasing the throughput of a multiplexed electrical bus by exploiting available pipeline stages of a computer or other system. For example, a method for increasing a throughput of an electrical bus that connects at least two devices in a system comprises introducing at least one signal hold stage in a signal-receiving one of the two devices, such that a maximum frequency at which the two devices are operated is not limited by a number of cycles of an operating frequency of the electrical bus needed for a signal to propagate from a signal-transmitting one of the two devices to the signal-receiving one of the two devices. Preferably, the signal hold stage introduced in the signal-receiving one of the two devices is a pipeline stage re-allocated from the signal-transmitting one of the two devices.

Assessment on the occupational exposure of urban public bus drivers to bioaccessible trace metals through resuspended fraction of settled bus dust

Energy Technology Data Exchange (ETDEWEB)

Gao, Peng [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090 (China); Stockbridge School of Agriculture, University of Massachusetts, Amherst, MA 01003 (United States); Liu, Sa [Environmental Health Sciences Division, School of Public Health, University of California, Berkeley, CA, 94720-7360 (United States); Ye, Wenyuan [Department of Chemical Engineering, KU Leuven, Willem de Croylaan 46, B-3001 Heverlee (Belgium); Lin, Nan; Meng, Ping [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090 (China); Feng, Yujie, E-mail: yujief@hit.edu.cn [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090 (China); Zhang, Zhaohan; Cui, Fuyi; Lu, Binyu [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, No. 73 Huanghe Road, Nangang District, Harbin 150090 (China); Xing, Baoshan [Stockbridge School of Agriculture, University of Massachusetts, Amherst, MA 01003 (United States)

2015-03-01

Limited information is available on the bioaccessible fraction of trace metals in the resuspended fraction of settled bus dust in order to estimate bus drivers ' occupational exposure. In this study, 45 resuspended fraction of settled dust samples were collected from gasoline and compressed natural gas (CNG) powered buses and analyzed for trace metals and their fraction concentrations using a three-step sequential extraction procedure. Experimental results showed that zinc (Zn) had the greatest bioaccessible fraction, recorded as an average of 608.53 mg/kg, followed in order of decreasing concentration by 129.80 mg/kg lead (Pb), 56.77 mg/kg copper (Cu), 34.03 mg/kg chromium (Cr), 22.05 mg/kg nickel (Ni), 13.17 mg/kg arsenic (As) and 2.77 mg/kg cadmium (Cd). Among the three settled bus dust exposure pathways, ingestion was the main route. Total exposure hazard index (HIt) for non-carcinogenic effect trace metals was lower than the safety level of 1. The incremental lifetime cancer risk (ILCR) for drivers was estimated for trace metal exposure. Pb and Ni presented relatively high potential risks in the non-carcinogenic and potentially carcinogenic health assessment for all drivers. ILCR was in the range of 1.84E − 05 to 7.37E − 05 and 1.74E − 05 to 6.95E − 05 for gasoline and CNG buses, respectively. - Highlights: • As, Cd and Ni had relatively higher bioaccessibility and mobility in the resuspended fraction of settled bus dust. • Bioaccessible metal concentrations were higher in gasoline-fueled buses than those in CNG-fueled buses. • The carcinogenic risk probabilities to drivers were around the acceptable level.

Computer-Based Video Instruction to Teach Students with Intellectual Disabilities to Use Public Bus Transportation

Science.gov (United States)

Mechling, Linda; O'Brien, Eileen

2010-01-01

This study investigated the effectiveness of computer-based video instruction (CBVI) to teach three young adults with moderate intellectual disabilities to push a "request to stop bus signal" and exit a city bus in response to target landmarks. A multiple probe design across three students and one bus route was used to evaluate effectiveness of…

Bus bays inventory using a terrestrial laser scanning system

Directory of Open Access Journals (Sweden)

Bobkowska Katarzyna

2017-01-01

Full Text Available This article presents the use of laser scanning technology for the assessment of bus bay geo-location. Ground laser scanning is an effective tool for collecting three-dimensional data. Moreover, the analysis of a point cloud dataset can be a source of a lot of information. The authors have outlined an innovative use of data collection and analysis using the TLS regarding information on the flatness of bus bays. The results were finalized in the form of colour three-dimensional maps of deviations and pavement type.

Design of temperature monitoring system based on CAN bus

Science.gov (United States)

Zhang, Li

2017-10-01

The remote temperature monitoring system based on the Controller Area Network (CAN) bus is designed to collect the multi-node remote temperature. By using the STM32F103 as main controller and multiple DS18B20s as temperature sensors, the system achieves a master-slave node data acquisition and transmission based on the CAN bus protocol. And making use of the serial port communication technology to communicate with the host computer, the system achieves the function of remote temperature storage, historical data show and the temperature waveform display.

Assessment of Passenger Satisfaction with Public Bus Transport Services: A Case Study of Lucknow City (India

Directory of Open Access Journals (Sweden)

Singh Sanjay

2016-12-01

Full Text Available The main aim of this study is threefold. First, it tries to assess the passenger satisfaction with public bus transport services in the city of Lucknow in India. Second, it tries to examine the service quality attributes that influence the passenger satisfaction. Third, it tries to evaluate the relative importance of service quality attributes to find out the priority for service quality improvements to enhance passenger satisfaction. The study is based on a survey of objective as well as subjective questions conducted between May and July 2014. Five major bus stops of Lucknow were selected for the survey. Total 148 respondents were randomly selected to elicit their overall satisfaction and factors that influence their satisfaction in the use of public bus transport services in Lucknow using a self-rated questionnaire. The collected sample of responses is subjected to principal component analysis, a statistical technique for dimensionality reduction of the dataset, and descriptive analysis. The result of theses analyses shows that passengers are mostly dissatisfied with public bus transport services in Lucknow. Using principal component analysis, five underlying factors were extracted that influenced passenger satisfaction with public bus transport services in the city. Out of these five factors, comfort and safety has the greatest impact on overall satisfaction, followed by the adequacy of capacity of public bus transport services, orderly and clean environment inside buses, elegant design of buses and bus stops, and accessibility to public bus transport services in the city. The study thus provides a direction for public bus transport administration in the city to understand the gaps that exist and try to fill them to improve its services so that passenger satisfaction can be enhanced and consequently more people can be attracted towards public bus transport.

School Transportation Issues, Laws and Concerns: Implications for Future Administrators

Science.gov (United States)

Durick, Jody M.

2010-01-01

Nearly all building administrators are confronted with a variety of transportation issues. Challenges, concerns and questions can arise from various aspects, including student misbehaviors, transportation laws and its implications at the school level, to importance and implementation of a school bus safety program. As new and upcoming future…

An assessment of commercial motor vehicle driver distraction using naturalistic driving data.

Science.gov (United States)

Hickman, Jeffrey S; Hanowski, Richard J

2012-01-01

This study analyzed naturalistic driving data from commercial trucks (3-axle and tractor-trailer/tanker) and buses (transit and motorcoach) during a 3-month period. The data set contained 183 commercial truck and bus fleets comprising 13,306 vehicles and included 1085 crashes, 8375 near crashes, 30,661 crash-relevant conflicts, and 211,171 baseline events. Study results documented the prevalence of tertiary tasks and the risks associated with performing these tasks while driving. Results indicated the odds of involvement in a safety-critical event differed as a function of performing different cell phone-related subtasks while driving. Although the odds ratio for talking/listening on a cell phone while driving was found to not significantly increase the likelihood of involvement in a safety-critical event, other cell phone subtasks (e.g., texting, dialing, reaching) were found to significantly increase the odds of involvement in a safety-critical event. The results suggest that cell phone use while driving should not be considered a simple dichotomous task (yes/no). Consideration should instead be made for a set of discrete cell phone subtasks that are each associated with varying levels of risk. Several hypotheses are presented to explain why cell phone use while driving was found to not increase the likelihood of involvement in a safety-critical event.

The ACP [Advanced Computer Program] Branch bus and real-time applications of the ACP multiprocessor system

International Nuclear Information System (INIS)

Hance, R.; Areti, H.; Atac, R.

1987-01-01

The ACP Branchbus, a high speed differential bus for data movement in multiprocessing and data acquisition environments, is described. This bus was designed as the central bus in the ACP multiprocessing system. In its full implementation with 16 branches and a bus switch, it will handle data rates of 160 MByte/sec and allow reliable data transmission over inter rack distances. We also summarize applications of the ACP system in experimental data acquisition, triggering and monitoring, with special attention paid to FASTBUS environments

Understanding the drive to escort: a cross-sectional analysis examining parental attitudes towards children’s school travel and independent mobility

Directory of Open Access Journals (Sweden)

Mammen George

2012-10-01

Full Text Available Abstract Background The declining prevalence of Active School Transportation (AST has been accompanied by a decrease in independent mobility internationally. The objective of this study was to compare family demographics and AST related perceptions of parents who let their children walk unescorted to/from school to those parents who escort (walk and drive their children to/from school. By comparing these groups, insight was gained into how we may encourage greater AST and independent mobility in youth living in the Greater Toronto and Hamilton Area, Canada. Methods This study involved a cross-sectional design, using data from a self-reported questionnaire (n =1,016 that examined parental perceptions and attitudes regarding AST. A multinomial logistic regression analysis was used to explore the differences between households where children travelled independently to school or were escorted. Results Findings revealed that unescorted children were: significantly older, the families spoke predominantly English at home, more likely to live within one kilometer from school, and their parents agreed to a greater extent that they chose to reside in the current neighborhood in order for their child to walk to/from school. The parents of the escorted children worried significantly more about strangers and bullies approaching their child as well as the traffic volume around school. Conclusions From both a policy and research perspective, this study highlights the value of distinguishing between mode (i.e., walking or driving and travel independence. For policy, our findings highlight the need for planning decisions about the siting of elementary schools to include considerations of the impact of catchment size on how children get to/from school. Given the importance of age, distance, and safety issues as significant correlates of independent mobility, research and practice should focus on the development and sustainability of non-infrastructure programs

Analysing passenger arrivals rates and waiting time at bus stops

OpenAIRE

Kaparias, I.; Rossetti, C.; Trozzi, V.

2015-01-01

The present study investigates the rather under-explored topic of passenger waiting times at public transport facilities. Using data collected from part of London’s bus network by means of physical counts, measurements and observations, and complemented by on-site passenger interviews, the waiting behaviour is analysed for a number of bus stops served by different numbers of lines. The analysis employs a wide range of statistical methods and tools, and concentrates on three aspects: passenger...

Optimal Locations of Bus Stops Connecting Subways near Urban Intersections

Directory of Open Access Journals (Sweden)

Yuan Cui

2015-01-01

Full Text Available Unsuitable locations of bus stops which provide feeder transportation connecting subways near urban intersections usually lead to the low efficiency of public transport and level of passenger service. A multiobjective optimization model to distribute such stop locations is proposed to attain the shortest total walk distance of passengers and minimum delay time of cars through intersections and travel time of buses. The Pareto frontier and optimal solutions for the proposed model are given by the distance-based and enumerative methods. The Xizhimen bus stop is selected to implement case studies for verifying the validity of the proposed model. The analysis of sensitivity on possible solutions is also carried out in the case studies. The results show that the proposed model is capable of optimizing the locations of bus stops connecting subways near intersections and helpful to improve the level of passengers service and operational efficiency of public transportation.

Designing Universitas Indonesia Molina EV Bus Dashboard Using ECQFD and TRIZ

Science.gov (United States)

Faiq Pradhila, Muhammad; Suzianti, Amalia; Putri Adinda, Prilly

2018-01-01

Universitas Indonesia is involved in the national electric car development program. One of the focus by the research team is to develop the Molina EV Bus which is planned to replace the current operational bus at UI so that it can be more environmental friendly. With UI developing facilities for the disabled, the Molina research team planned to make a new prototype of the Molina EV Bus to contribute to the facilities developed for the disabled. The new prototype is expected to increase the quality of the previous features of the EV Bus, including the dashboard that had been ignored. To support the development of the new prototype, this research was conducted to design a suitable dashboard for the new prototype. Design of the prototype are made using Autodesk Inventor. This research used the integration of ECQFD (Environmentally Conscious Quality Function Deployment) and TRIZ (Theory of Inventive Problem Solving) method. ECQFD was used to translate user needs into quality characteristics based on environmental aspects. TRIZ was used to translate the quality characteristics into technical specifications. This research has generated 3 sustainable, innovative, and user-preferred dashboard design recommendation for the new prototype.

Electric bus migration in Bengaluru with dynamic charging technologies

Directory of Open Access Journals (Sweden)

Ankit Kumar Begwani

2017-12-01

Full Text Available Rapid but unplanned urban development coupled with economic growth has resulted in congestion and pollution concerns in Indian cities. This forced India consider taking concrete steps towards design policies that would help stir the nation towards a more sustainable future. India, along with other bigger Asian economies like China, needs to address the growing global concerns over climate change and design their framework and policies to help cut down the greenhouse gas emissions. Transportation is a major source of pollution. A shift towards a pro-public transport policy would solve the traffic congestion problems and address the emission concerns. India has a significantly higher modal share of public transportation in its major cities. Public bus transport system acts as a lifeline to the India’s poor and middle class citizens. The following study focuses on the need for a replacement of conventional fossil fuel dependent buses with Electric buses in the existing public transport bus fleet in the city of Bengaluru. A design has been developed to utilize wireless charging technologies to realize electric bus migration in Bengaluru.

DETERMINATION OF THE DELAY DEPARTURE TIME OF THE BUS FROM STOPPING POINT INTO THE CAR FLOW

Directory of Open Access Journals (Sweden)

P. Gorbachov

2014-10-01

Full Text Available An analytical model for estimation of the bus departure delax from the bus stopping point after passenger loading is presented. The model allows to take into account the traffic density on a particular road section of the transport network, as well as the bus parameters.

Energy efficient motion control of the electric bus on route

Science.gov (United States)

Kotiev, G. O.; Butarovich, D. O.; Kositsyn, B. B.

2018-02-01

At present, the urgent problem is the reduction of energy costs of urban motor transport. The article proposes a method of solving this problem by developing an energy-efficient law governing the movement of an electric bus along a city route. To solve this problem, an algorithm is developed based on the dynamic programming method. The proposed method allows you to take into account the constraints imposed on the phase coordinates, control action, as well as on the time of the route. In the course of solving the problem, the model of rectilinear motion of an electric bus on a horizontal reference surface is considered, taking into account the assumptions that allow it to be adapted for the implementation of the method. For the formation of a control action in the equations of motion dynamics, an algorithm for changing the traction / braking torque on the wheels of an electric bus is considered, depending on the magnitude of the control parameter and the speed of motion. An optimal phase trajectory was obtained on a selected section of the road for the prototype of an electric bus. The article presents the comparison of simulation results obtained with the optimal energy efficient control law with the results obtained by a test driver. The comparison proved feasibility of the energy efficient control law for the automobile city electric transport.

Aerodynamic study of state transport bus using computational fluid dynamics

Science.gov (United States)

Kanekar, Siddhesh; Thakre, Prashant; Rajkumar, E.

2017-11-01

The main purpose of this study was to develop the aerodynamic study of a Maharashtra state road transport bus. The rising fuel price and strict government regulations makes the road transport uneconomical now days. With the objective of increasing fuel efficiency and reducing the emission of harmful exhaust gases. It has been proven experimentally that vehicle consumes almost 40% of the available useful engine power to overcome the drag resistance. This provides us a huge scope to study the influence of aerodynamic drag. The initial of the project was to identify the drag coefficient of the existing ordinary type model called “Parivartan” from ANSYS fluent. After preliminary analysis of the existing model corresponding changes are made in such a way that their implementation should be possible at workshop level. The simulation of the air flow over the bus was performed in two steps: design on SolidWorks CAD and ANSYS (FLUENT) is used as a virtual analysis tool to estimate the drag coefficient of the bus. We have used the turbulence models k-ε Realizable having a better approximation of the actual result. Around 28% improvement in the drag coefficient is achieved by CFD driven changes in the bus design. Coefficient of drag is improved by 28% and fuel efficiency increased by 20% by CFD driven changes.

Steering characteristic of an articulated bus under quasi steady maneuvering

Science.gov (United States)

Ubaidillah, Setiawan, Budi Agus; Aridharma, Airlangga Putra; Lenggana, Bhre Wangsa; Caesar, Bernardus Placenta Previo

2018-02-01

Articulated buses have been being preferred as public transportation modes due to their operational capacity. Therefore, passenger safety must be the priority of this public service vehicle. This research focused on the analytical approach of steering characteristics of an articulated bus when it maneuvered steadily. Such turning condition could be referred as a stability parameter of the bus for preliminary handling assessment. The analytical approach employed kinematics relationship between front and rear bodies as well as steering capabilities. The quasi steady model was developed to determine steering parameters such as turning radius, oversteer, and understeer. The mathematical model was useful for determining both coefficients of understeer and oversteer. The dimension of articulated bus followed a commonly used bus as utilized in Trans Jakarta busses. Based on the simulation, for one minimum center of the body, the turning radius was calculated about 8.8 m and 7.6 m at steady turning speed of 10 km/h. In neutral condition, the minimum road radius should be 6.5 m at 10 km/h and 6.9 m at 40 km/h. For two centers of the body and oversteer condition, the front body has the turning radius of 8.8 m, while, the rear body has the turning radius of 9.8 m at both turning speeds of 40 km/h. The other steering parameters were discussed accordingly.

Large truck and bus crash facts, 2010.

Science.gov (United States)

2012-09-01

This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2010. Selected crash statistics on passenger : vehicles are also presen...

Large truck and bus crash facts, 2012.

Science.gov (United States)

2014-06-01

This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2012. Selected crash statistics on passenger vehicles are also presented ...

Large truck and bus crash facts, 2013.

Science.gov (United States)

2015-04-01

This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2013. Selected crash statistics on passenger vehicles are also presented ...

Large truck and bus crash facts, 2009.

Science.gov (United States)

2011-10-01

This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2009. Selected crash statistics on passenger : vehicles are also presen...

Large truck and bus crash facts, 2011.

Science.gov (United States)

2013-10-01

This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2011. Selected crash statistics on passenger : vehicles are also presen...

Converter Power Density Increase using Low Inductive Integrated DC-link Capacitor/Bus

DEFF Research Database (Denmark)

Trintis, Ionut; Franke, Toke; Rannested, Bjørn

2015-01-01

The power losses in switching devices have a direct effect on the maximum converter power. For a voltage source converter, the DC-link bus has a major influence on the power loss and safe operating area of the power devices. The Power Ring Film CapacitorTM integrated with an optimized bus structu...

Biobjective Optimization and Evaluation for Transit Signal Priority Strategies at Bus Stop-to-Stop Segment

Directory of Open Access Journals (Sweden)

Rui Li

2016-01-01

Full Text Available This paper proposes a new optimization framework for the transit signal priority strategies in terms of green extension, red truncation, and phase insertion at the stop-to-stop segment of bus lines. The optimization objective is to minimize both passenger delay and the deviation from bus schedule simultaneously. The objective functions are defined with respect to the segment between bus stops, which can include the adjacent signalized intersections and downstream bus stops. The transit priority signal timing is optimized by using a biobjective optimization framework considering both the total delay at a segment and the delay deviation from the arrival schedules at bus stops. The proposed framework is evaluated using a VISSIM model calibrated with field traffic volume and traffic signal data of Caochangmen Boulevard in Nanjing, China. The optimized TSP-based phasing plans result in the reduced delay and improved reliability, compared with the non-TSP scenario under the different traffic flow conditions in the morning peak hour. The evaluation results indicate the promising performance of the proposed optimization framework in reducing the passenger delay and improving the bus schedule adherence for the urban transit system.

SunLine Transit Agency Advanced Technology Fuel Cell Bus Evaluation: Second Results Report and Appendices

Energy Technology Data Exchange (ETDEWEB)

Eudy, L.; Chandler, K.

2011-10-01

This report describes operations at SunLine Transit Agency for their newest prototype fuel cell bus and five compressed natural gas (CNG) buses. In May 2010, SunLine began operating its sixth-generation hydrogen fueled bus, an Advanced Technology (AT) fuel cell bus that incorporates the latest design improvements to reduce weight and increase reliability and performance. The agency is collaborating with the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to evaluate the bus in revenue service. This is the second results report for the AT fuel cell bus since it was placed in service, and it focuses on the newest data analysis and lessons learned since the previous report. The appendices, referenced in the main report, provide the full background for the evaluation. They will be updated as new information is collected but will contain the original background material from the first report.

New TPG bus route 28

CERN Multimedia

2003-01-01

Geneva's Public Transport services (TPG) have recently inaugurated a new bus line 28, connecting the La Tour Hospital in Meyrin to the international organisations in Geneva, via the airport. All signs associated with this route will be yellow in colour. Timetables and route details can be found at http://www.tpg.ch. Relations with the Host States Service http://www.cern.ch/relations/ Tel. 72848

Avionic Data Bus Integration Technology

Science.gov (United States)

1991-12-01

address the hardware-software interaction between a digital data bus and an avionic system. Very Large Scale Integration (VLSI) ICs and multiversion ...the SCP. In 1984, the Sperry Corporation developed a fault tolerant system which employed multiversion programming, voting, and monitoring for error... MULTIVERSION PROGRAMMING. N-version programming. 226 N-VERSION PROGRAMMING. The independent coding of a number, N, of redundant computer programs that

Analysis of bus passenger comfort perception based on passenger load factor and in-vehicle time.

Science.gov (United States)

Shen, Xianghao; Feng, Shumin; Li, Zhenning; Hu, Baoyu

2016-01-01

Although bus comfort is a crucial indicator of service quality, existing studies tend to focus on passenger load and ignore in-vehicle time, which can also affect passengers' comfort perception. Therefore, by conducting surveys, this study examines passengers' comfort perception while accounting for both factors. Then, using the survey data, it performs a two-way analysis of variance and shows that both in-vehicle time and passenger load significantly affect passenger comfort. Then, a bus comfort model is proposed to evaluate comfort level, followed by a sensitivity analysis. The method introduced in this study has theoretical implications for bus operators attempting to improve bus service quality.

Hurried driving: Relationship to distress tolerance, driver anger, aggressive and risky driving in college students.

Science.gov (United States)

Beck, Kenneth H; Daughters, Stacey B; Ali, Bina

2013-03-01

Being a hurried driver is associated with a variety of risky driving behaviors, yet the mechanisms underlying this behavior remain unknown. Distress tolerance, defined as an individual's capability to experience and endure negative emotional states, was examined as a predictor of hurried driving among 769 college students. Results indicate that after controlling for age, gender, race, ethnicity, the student's year in school, their grade point average, driving frequency, angry driving, aggressive driving as well as other forms of self-reported risky driving; hurried driving was significantly associated with lower levels of distress tolerance. Hurried drivers also reported greater levels of frustration and impatience with other drivers, suggesting that they have difficulty in withstanding or coping with negative psychological states when driving. Traditional traffic safety campaigns that emphasize enforcement may be less successful with these drivers. The need to develop campaigns that address the affective coping abilities that contribute to this behavioral pattern is discussed. Copyright © 2012 Elsevier Ltd. All rights reserved.

49 CFR 37.169 - Interim requirements for over-the-road bus service operated by private entities.

Science.gov (United States)

2010-10-01

... of such devices, shall be permitted in the passenger compartment. When the bus is at rest at a stop... 49 Transportation 1 2010-10-01 2010-10-01 false Interim requirements for over-the-road bus service... Interim requirements for over-the-road bus service operated by private entities. (a) Private entities...

Switch/router architectures shared-bus and shared-memory based systems

CERN Document Server

Aweya, James

2018-01-01

A practicing engineer's inclusive review of communication systems based on shared-bus and shared-memory switch/router architectures. This book delves into the inner workings of router and switch design in a comprehensive manner that is accessible to a broad audience. It begins by describing the role of switch/routers in a network, then moves on to the functional composition of a switch/router. A comparison of centralized versus distributed design of the architecture is also presented. The author discusses use of bus versus shared-memory for communication within a design, and also covers Quality of Service (QoS) mechanisms and configuration tools. Written in a simple style and language to allow readers to easily understand and appreciate the material presented, Switch/Router Architectures: Shared-Bus and Shared-Memory Based Systems discusses the design of multilayer switches—starting with the basic concepts and on to the basic architectures. It describes the evolution of multilayer switch designs and highli...

Design of belt conveyor electric control device based on CC-link bus

Science.gov (United States)

Chen, Goufen; Zhan, Minhua; Li, Jiehua

2016-01-01

In view of problem of the existing coal mine belt conveyor is no field bus communication function, two levels belt conveyor electric control system design is proposed based on field bus. Two-stage belt conveyor electric control system consists of operation platform, PLC control unit, various sensors, alarm device and the water spraying device. The error protection is realized by PLC programming, made use of CC-Link bus technology, the data share and the cooperative control came true between host station and slave station. The real-time monitor was achieved by the touch screen program. Practical application shows that the system can ensure the coalmine production, and improve the automatic level of the coalmine transport equipment.

Calculation of Flexible Bus-Bars Electrodynamic Stability with Application of Implicit Scheme

Directory of Open Access Journals (Sweden)

Y. G. Panamarenka

2008-01-01

Full Text Available A numerical method for calculation of open-air substations’ flexible bus-bars dynamic at short-circuit has been improved on equations of a flexible elastic string with application of an implicit scheme. On the basis of the numerical method a computer program FLEBUS for calculation of substations’ flexible bus-bars dynamic at short-circuit has been developed. An approbation and an estimation of calculation result reliability have been carried out in accordance with the program while using experimental data. On the basis of the obtained information it is possible to assert that the developed program is an independent tool for calculation of electrodynamic stability of substations’ flexible bus-bars.

Perceptions of Crisis Management in a K-12 School District

Science.gov (United States)

Tucker, Joy

2012-01-01

This multiple-case qualitative study was conducted to examine the perceptions of community members, students, and staff regarding school crisis management following a 2006 tornado and 2010 bus accident in a small rural school district in Missouri. Online surveys were collected from 66 participants, and 10 follow-up interviews were completed with…

Evaluating the Impacts of Bus Fare on Social Equity Based on IC Card Data in China

Directory of Open Access Journals (Sweden)

Shaowu Cheng

2016-10-01

Full Text Available Bus fare equity has attracted significant attention in China in the past few years. Compared with developed countries, China’s intelligent transportation systems are in their infancy, with immature bus fare policies being used in many public transit systems. The methods used for evaluating public transit fare equity in developed countries compare different fare policies based on rich data and cannot be directly applied in developing countries like China. In this paper, we present a method that uses IC card data, bus-mounted GPS data, and relevant statistical yearbook data to evaluate the equity of flat bus fare. The method ranks the factors that influence the impacts of bus fare on social equity for different passenger groups and indicates that trip distance and passenger boarding time are the two primary factors for bus fare equity from a resource allocation perspective. Finally, we present a case study that evaluates the flat fare policy for route 204 in Suzhou using the proposed method. The results show that the proposed method is feasible.

Users' demographic profile and quality attributes of bus services: The perspectives of users, operators and local authorities

Science.gov (United States)

Noh, Nur'Amirah Mhd.; Hamid, Ahmad Hilmy Abd

2017-10-01

Bus services that can help meet almost every bus user's needs are the goals of bus operators. Despite such an idealistic view, the operators themselves, users and even the local authorities have been found to hold different views about the quality of service that the bus should deliver. As the users i.e., customers are considered as important stakeholders, understanding their characteristics, profile and pattern is very crucial. To this end, the present study has attempted to gauge the perspectives of all the above-mentioned stakeholders. For the users, a customer satisfaction survey was employed to look into the relative influence of service attributes. In addition, surveys were also administered to bus operators and local authorities to study their perspectives in relation to this matter. 450 randomly selected respondents were surveyed. Identification of the service level was analyzed through the Likert scale whereas the perspectives of the operators and authorities were dealt with through mean value Analysis. Specifically, this study aims to identify the crucial attributes in determining the quality of the bus services. Findings of the study indicated that different attributes were selected by users, operators and authorities, which clearly enlightened the variations of the important attributes in determining the level of bus service quality. In its attempt to compare the service level attributes from three perspectives, this study has helped advance better improvement and strategies for the urban public bus operators and planners, in addition to the authorities in delivering user-friendly bus services by taking into account the local context, user profile and demographic characteristics.

The impact of bus drivers ’ lifestyle on the occurrence of health problems and absenteeism

OpenAIRE

Andrej Jerman; Maja Meško

2016-01-01

Research Question: Do bus drivers’ lifestyles affect the occurrence of health problems and absenteeism? Purpose: The purpose of the study was to determine whether the lifestyle of professional bus drivers affects the occurrence of health problems and the phenomenon of absenteeism. Method: A quantitative research method was used in the research. Data were collected using a structured questionnaire, on a sample of 230 professional bus drivers from differ...

The impact of bus drivers ’ lifestyle on the occurrence of health problems and absenteeism

Directory of Open Access Journals (Sweden)

Andrej Jerman

2016-06-01

Full Text Available Research Question: Do bus drivers’ lifestyles affect the occurrence of health problems and absenteeism? Purpose: The purpose of the study was to determine whether the lifestyle of professional bus drivers affects the occurrence of health problems and the phenomenon of absenteeism. Method: A quantitative research method was used in the research. Data were collected using a structured questionnaire, on a sample of 230 professional bus drivers from different bus transport companies in Slovenia. Selected data were analyzed with chi-square test and multiple regression analysis. Results: We determined that there is a relationship between the state of health of professional bus drivers and participation in sport activity and that there is a statistically significant impact of lifestyle on the absenteeism of professional bus drivers. Organization: The study points to the necessity of management’s awareness to improve the conditions for the health status of employees and, consequently, absenteeism. Managers need to be more vigilant in ensuring conditions and social security that will allow employees a higher quality lifestyle. Society: The poor quality lifestyle of professional bus drivers, which includes different addictions, inadequate physical activity, and poor working conditions, is a significant factor causing absenteeism. All these factors influence the onset of negative consequences, such as the direct cost of compensation payments, costs of replacing the absent person, a reduction in productivity, which in turn affect economic growth and the high cost of health care. Originality: This is the first focus group study of professional bus drivers that targets lifestyle and its connection to absenteeism. Limitations/Future Research: The main limitation of the study is the number of respondents. The reason for this is that professional drivers are less responsive in the survey and that the study was conducted only in Slovenia, country of two

Lightweight power bus for a baseload nuclear reactor in space

International Nuclear Information System (INIS)

Oberly, C.E.; Massie, L.D.; Hoffman, D.J.

1989-01-01

Space environmental interactions with the power distribution/power processing subsystem can become a serious problem for power systems rated at 10's to 100's of kilowatts. Utilization of ceramic superconductors at 1000 A/cm/sup 2/, which has already been demonstrated at 77 K in a conductor configuration may eliminate both bus mass and distribution voltage problems in a high power satellite. The analytical results presented here demonstrate that a superconducting coaxial power transmission bus offers significant benefits in reduced distribution voltage and mass

Hearing Impairment and High Blood Pressure among Bus Drivers in Puducherry.

Science.gov (United States)

Balaji, Rajeshwar; Rajasegaran, Rajalakshmi; John, Nitin Ashok; Venkatappa, Umadevi Sajja

2016-02-01

Noise Induced Hearing Loss (NIHL), a major heath concern due to constant exposure to loud noise is on the rising trend in today's world. The bus drivers are more vulnerable to the auditory and non-auditory ill effects of noise pollution. The aim of this study was to assess and compare the hearing level, blood pressure and peak expiratory flow rate of bus drivers and individuals employed in office jobs. Fifty male bus drivers aged 30-50 years and fifty males of the same group employed in office jobs were recruited as the test and control groups respectively. The hearing level of the individuals in both the groups was assessed using the Hearing Deterioration Index (HDI). The lung function and cardiovascular status of the study participants were assessed by measuring their Peak Expiratory Flow Rate (PEFR) and Blood Pressure (BP) respectively. The mean HDI, PEFR and BP values of both the groups were compared using the unpaired t-test and the extent of correlation between HDI, service years, exposure level, systolic blood pressure (SBP) and diastolic blood pressure (DBP) was determined using Pearson correlation coefficient test. HDI, SBP and DBP were significantly higher among the bus drivers when compared to the controls. However, there was no significant difference in the PEFR values between the test and the control groups. There was a highly significant positive correlation between HDI and service years and exposure level. Similarly, there was a significant positive correlation between exposure level and systolic and diastolic blood pressure. Prolonged exposure to high intensity of sound results in deterioration of hearing capacity and increase in blood pressure among the bus drivers.

Demand estimation of bus as a public transport based on gravity model

Directory of Open Access Journals (Sweden)

Asmael Noor

2018-01-01

Full Text Available Bus as a public transport is a suitable service to meet the travel demand between any two zones. Baghdad faced with severe traffic problems along with the development in city size and economy. Passengers have to wait lots of time during commutation to work because of the serious traffic jams. In the last years, rate of car ownership has increased as income levels have gone up and cars have become a preferable mode of transport. Bus, as the only public mode of transport available, is suffering from inconvenience, slowness, and inflexibility. A big emphasis must be given to the public transport system because it introduces an active utilization of limited resources, energy and land. This study determines the demand of public routes for buses using boarding / alighting values to generate a model and assign these demand values to the bus network. Five public routes were selected to collect the required data. Ride check and Point check survey was conducted for each selected route. The results of this study were public demand assigned to the selected bus routes, dwell time, load factor and headway. It is observed that R1 and R3 have the heaviest travel demand; they need special study to improve bus performance and make better transit. The model developed with only limited data available to predict travel demand will assist transportation planners and related agencies in decision making.

Modeling and Simulation of Bus Dispatching Policy for Timed Transfers on Signalized Networks

Science.gov (United States)

Cho, Hsun-Jung; Lin, Guey-Shii

2007-12-01

The major work of this study is to formulate the system cost functions and to integrate the bus dispatching policy with signal control. The integrated model mainly includes the flow dispersion model for links, signal control model for nodes, and dispatching control model for transfer terminals. All such models are inter-related for transfer operations in one-center transit network. The integrated model that combines dispatching policies with flexible signal control modes can be applied to assess the effectiveness of transfer operations. It is found that, if bus arrival information is reliable, an early dispatching decision made at the mean bus arrival times is preferable. The costs for coordinated operations with slack times are relatively low at the optimal common headway when applying adaptive route control. Based on such findings, a threshold function of bus headway for justifying an adaptive signal route control under various time values of auto drivers is developed.

On the road : non-fossil fuel deployment for the public bus fleet of Sweden

OpenAIRE

Xylia, Maria; Silveira, Semida

2015-01-01

The public transport sector in Sweden has set a target to run 90% of its total vehicle-kilometers on renewable fuels by 2020, and double its market share in the long term. The focus of this paper is the adoption of renewable fuels in public bus fleets. Data for all 21 Swedish counties were gathered and analyzed, mapping the bus fleets’ condition in relation to renewable fuel deployment, CO2 emissions and energy efficiency. The main factors affecting fuel choices in the bus fleets were investi...

Aerosol particles generated by diesel-powered school buses at urban schools as a source of children's exposure.

Science.gov (United States)

Hochstetler, Heather A; Yermakov, Mikhail; Reponen, Tiina; Ryan, Patrick H; Grinshpun, Sergey A

2011-03-01

Various heath effects in children have been associated with exposure to traffic-related particulate matter (PM), including emissions from school buses. In this study, the indoor and outdoor aerosol at four urban elementary schools serviced by diesel-powered school buses was characterized with respect to the particle number concentrations and size distributions as well as the PM2.5 mass concentrations and elemental compositions. It was determined that the presence of school buses significantly affected the outdoor particle size distribution, specifically in the ultrafine fraction. The time-weighted average of the total number concentration measured outside the schools was significantly associated with the bus and the car counts. The concentration increase was consistently observed during the morning drop-off hours and in most of the days during the afternoon pick-up period (although at a lower degree). Outdoor PM2.5 mass concentrations measured at schools ranged from 3.8 to 27.6 µg m -3 . The school with the highest number of operating buses exhibited the highest average PM2.5 mass concentration. The outdoor mass concentrations of elemental carbon (EC) and organic carbon (OC) were also highest at the school with the greatest number of buses. Most (47/55) correlations between traffic-related elements identified in the outdoor PM2.5 were significant with elements identified in the indoor PM2.5. Significant associations were observed between indoor and outdoor aerosols for EC, EC/OC, and the total particle number concentration. Day-to-day and school-to-school variations in Indoor/Outdoor (I/O) ratios were related to the observed differences in opening windows and doors, which enhanced the particle penetration, as well as indoor activities at schools. Overall, the results on I/O ratio obtained in this study reflect the sizes of particles emitted by diesel-powered school bus engines (primarily, an ultrafine fraction capable of penetrating indoors).

Performance Analysis of Regenerative Braking in Permanent Magnet Synchronous Motor Drives

Directory of Open Access Journals (Sweden)

Andrew Adib

2018-02-01

Full Text Available This paper describes the design and analysis of a regenerative braking system for a permanent magnet synchronous motor (PMSM drive for electric vehicle (EV applications. First studied is the principle for electric braking control of a PMSM motor under field-oriented control (FOC. Next, the maximum braking torque in the regeneration mode as well as the braking torque for the maximum regeneration power, respectively, are deduced. Additionally, an optimum switching scheme for the inverter is developed with the objective of maximizing energy recovery during regenerative braking to the DC-bus capacitor. The integration of an ultra-capacitor module with the battery allows for the efficient and high power transfer under regenerative braking. It was important to manage the power flow to the DC-bus as this is a key issue that affects the efficiency of the overall system. Finally, the amounts of braking energy that can be recovered, and the efficiency with which it can be returned to the battery/ultra-capacitor, is analyzed for a PMSM coupled with a DC motor as the load. The results of the analysis are validated through experimentation.

40 CFR 85.1404 - Maintenance of records for urban bus operators; submittal of information; right of entry.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Maintenance of records for urban bus... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Urban Bus Rebuild Requirements § 85.1404 Maintenance of records for urban bus operators; submittal...

Design of Bus Protocol Intelligent Initiation System Based On RS485

Directory of Open Access Journals (Sweden)

Li Liming

2017-01-01

Full Text Available In order to design an effective and reliable RS485 bus protocol based on RS485 bus, this paper introduces the structure and transmission mode of the command frame and the response frame, and also introduce four control measures and the communication in order to process quality of this system. The communication protocol is open, tolerant, reliable and fast, and can realize ignition more reliable and accurate in the intelligent initiation system.

Pilot survey of subway and bus stop noise levels.

Science.gov (United States)

Gershon, Robyn R M; Neitzel, Richard; Barrera, Marissa A; Akram, Muhammad

2006-09-01

Excessive noise exposure is a serious global urban health problem, adversely affecting millions of people. One often cited source of urban noise is mass transit, particularly subway systems. As a first step in determining risk within this context, we recently conducted an environmental survey of noise levels of the New York City transit system. Over 90 noise measurements were made using a sound level meter. Average and maximum noise levels were measured on subway platforms, and maximum levels were measured inside subway cars and at several bus stops for comparison purposes. The average noise level measured on the subway platforms was 86 +/- 4 dBA (decibel-A weighting). Maximum levels of 106, 112, and 89 dBA were measured on subway platforms, inside subway cars, and at bus stops, respectively. These results indicate that noise levels in subway and bus stop environments have the potential to exceed recommended exposure guidelines from the World Health Organization (WHO) and U.S. Environmental Protection Agency (EPA), given sufficient exposure duration. Risk reduction strategies following the standard hierarchy of control measures should be applied, where feasible, to reduce subway noise exposure.

Bus safety study : a report to Congress.

Science.gov (United States)

2013-11-01

Section 20021(b) of the Moving Ahead for Progress for the 21st Century (MAP-21) legislation requires the Secretary of Transportation : to submit a report of the results of a Bus Safety Study to the Committee on Banking, Housing, and Urban Affai...

Magnitude and correlates of bird collisions at glass bus shelters in an urban landscape.

Science.gov (United States)

Barton, Christine M; Riding, Corey S; Loss, Scott R

2017-01-01

Wildlife residing in urban landscapes face many human-related threats to their survival. For birds, collision with glass on manmade structures has been identified as a major hazard, causing hundreds of millions of avian fatalities in North America every year. Although research has investigated factors associated with bird-glass collision mortality at buildings, no prior studies have focused on bird fatalities at glass-walled bus shelters. Our objectives in this study were to describe the magnitude of bird-bus shelter collisions in the city of Stillwater, Oklahoma and assess potential predictors of collision risk, including characteristics of shelters (glass area) and surrounding land cover (e.g., vegetative features). We surveyed for bird carcasses and indirect collision evidence at 18 bus shelters over a five-month period. Linear regression and model selection results revealed that the amount of glass on shelters and the area of lawn within 50 m of shelters were both positively related to fatal bird collisions; glass area was also positively associated with observations of collision evidence on glass surfaces. After accounting for scavenger removal of carcasses, we estimate that a minimum of 34 birds are killed each year between May and September by collision with the 36 bus shelters in the city of Stillwater. While our study provides an initial look at bird fatalities at bus shelters, additional research is needed to generate a large-scale estimate of collision mortality and to assess species composition of fatalities at a national scale. Designing new bus shelters to include less glass and retrofitting existing shelters to increase visibility of glass to birds will likely reduce fatal bird collisions at bus shelters and thus reduce the cumulative magnitude of anthropogenic impacts to birds in cities.

Well-Being of Lagos Urban Mini-Bus Drivers: The Influence of Age and Marital Status

OpenAIRE

Bolajoko I. Malomo; Maryam O. Yusuf

2015-01-01

Lagos urban mini bus drivers play a critical role in the transportation sector. The current major mode of transportation within Lagos metropolis remains road transportation and this confirms the relevance of urban mini-bus drivers in transporting the populace to their various destinations. Other modes of transportation such as the train and waterways are currently inadequate. Various threats to the well-being of urban bus drivers include congested traffic typical of moder...

Dangers on the road: A longitudinal examination of passenger-initiated violence against bus drivers.

Science.gov (United States)

Zhou, Biru; Boyer, Richard; Guay, Stéphane

2018-04-01

This study examined the impact of workplace violence against 109 bus drivers over a 1-year span. Workplace violence is related to both psychological and work-related consequences. Our findings showed that bus drivers experienced a wide range of violence at work and the psychological consequences were devastating: Half of the participants met the diagnostic criteria for acute stress disorder within the first month following the index event. Majority of them experienced at least moderate levels of post-traumatic stress disorder (PTSD) problems over the 1-year span. About 9.3% of participants showed a delayed onset of PTSD 6 months after. Furthermore, counter-supportive behaviours and reexposure to violence played important roles in the maintenance of PTSD symptoms over time. Even though PTSD symptoms per se did not relate to bus driver's confidence in coping with aggressive passengers, the immediate post-traumatic reaction-symptoms of acute stress disorder-showed a significant long-term negative effect on bus drivers' confidence in dealing with aggressive passengers 12 months after. This study provided empirical evidence of the changing nature of PTSD symptoms over time among bus drivers. Copyright © 2017 John Wiley & Sons, Ltd.

Transition to a hydrogen fuel cell transit bus fleet for Canadian urban transit system

International Nuclear Information System (INIS)

Ducharme, P.

2004-01-01

'Full text:' The Canadian Transportation Fuel Cell Alliance (CTFCA), created by the Canadian Government as part of its 2000 Climate Change Action Plan, has commissioned MARCON-DDM's Hydrogen Intervention Team (HIT) to provide a roadmap for urban transit systems that wish to move to hydrogen fuel cell-powered bus fleets. HIT is currently in the process of gathering information from hydrogen technology providers, bus manufacturers, fuelling system providers and urban transit systems in Canada, the US and Europe. In September, HIT will be in a position to provide a preview of its report to the CTFCA, due for October 2004. The planned table of contents includes: TOMORROW'S FUEL CELL (FC) URBAN TRANSIT BUS - Powertrain, on-board fuel technologies - FC engine system manufacturers - Bus technical specifications, performances, operating characteristics - FC bus manufacturers TOMORROW'S FC TRANSIT PROPERTY - Added maintenance, facilities and fuelling infrastructure requirements - Supply chain implications - Environmental and safety issues - Alternative operational concepts PATHWAYS TO THE FUTURE - Choosing the future operational concept - 'Gap' assessment - how long from here to there? - Facilities and fleet adjustments, including fuelling infrastructure - Risk mitigation, code compliance measures TRANSITIONAL CONSIDERATIONS - Cost implications - Transition schedule (author)

Studies of self-pollution in diesel school buses: methodological issues.

Science.gov (United States)

Borak, Jonathan; Sirianni, Greg

2007-09-01

Considerable interest has focused on levels of exhaust emissions in the cabins of diesel-powered school buses and their possible adverse health effects. Significantly different policy and engineering issues would be raised if compelling evidence found that inc-cabin contamination was due to self-pollution from bus emissions, rather than ambient pollution, neighboring vehicles, and/or re-entrained road dust. We identified 19 reports from 11 studies that measured diesel exhaust particulate in the cabins of 58 school bus of various type. Studies were evaluated in light of their experimental design, their data quality, and their capacity to quantify self-pollution. Only one study had a true experimental design, comparing the same buses with and without emission controls, while four others used intentional tracers to quantify tail pipe and/or crankcase emissions. Although definitive data are still lacking, these studies suggest that currently available control technologies can nearly eliminate particulate self-pollution inside diesel school buses.

School Districts Move to the Head of the Class with Propane

Energy Technology Data Exchange (ETDEWEB)

None

2016-01-12

School districts across the country are under pressure to reduce their cost of operations and ensure their budgets are spent wisely. School bus fleets operate more than 675,000 buses in the United States, and many school districts have found the answer to their budget woes in the form of propane, or liquefied petroleum gas (LPG). Propane is a reliable, domestic fuel, and it's used in approximately 2% of school buses nationwide.

An observational comparison of the older and younger bus passenger experience in a developing world city.

Science.gov (United States)

Aceves-González, Carlos; May, Andrew; Cook, Sharon

2016-06-01

This study was an unobtrusive observational analysis of 333 older and younger bus passengers in Guadalajara, Mexico. A set of data were collected for each observed passenger, as well as more general observations related to driver behaviour, bus design and bus service characteristics. There were significant differences between older and younger passengers in terms of boarding and alighting times, use of handrails, seat location preferences, passenger stability and coping strategies in order to maintain postural stability. The conditions of travel are conducive to a poor passenger experience for the older passengers in particular. Although the problems may be attributed to bus design and driver behaviour typical of that in developing countries, they are also influenced by the wider transport infrastructure, and a lack of a regulatory regime which places drivers under time pressure and in direct competition with each other. Practitioner Summary: Bus services must cater for all ages of passengers, including the elderly. This unobtrusive observational study investigated the passenger experience in a developing world city. Bus and wider service design were found to compromise the journey experience, with the older users being particularly negatively impacted. Design recommendations are provided.

Evaluation of Effective Factors on Travel Time in Optimization of Bus Stops Placement Using Genetic Algorithm

Science.gov (United States)

Bargegol, Iraj; Ghorbanzadeh, Mahyar; Ghasedi, Meisam; Rastbod, Mohammad

2017-10-01

In congested cities, locating and proper designing of bus stops according to the unequal distribution of passengers is crucial issue economically and functionally, since this subject plays an important role in the use of bus system by passengers. Location of bus stops is a complicated subject; by reducing distances between stops, walking time decreases, but the total travel time may increase. In this paper, a specified corridor in the city of Rasht in north of Iran is studied. Firstly, a new formula is presented to calculate the travel time, by which the number of stops and consequently, the travel time can be optimized. An intended corridor with specified number of stops and distances between them is addressed, the related formulas to travel time are created, and its travel time is calculated. Then the corridor is modelled using a meta-heuristic method in order that the placement and the optimal distances of bus stops for that are determined. It was found that alighting and boarding time along with bus capacity are the most effective factors affecting travel time. Consequently, it is better to have more concentration on indicated factors for improving the efficiency of bus system.

Concentrations and risk assessment of selected monoaromatic hydrocarbons in buses and bus stations of Hangzhou, China.

Science.gov (United States)

Li, Shuang; Chen, Shuguang; Zhu, Lizhong; Chen, Xiasheng; Yao, Chaoying; Shen, Xueyou

2009-03-01

Air pollution surveys of ten selected monoaromatic hydrocarbons (MAHCs) were conducted in buses and bus stations in Hangzhou, China. The mean concentrations of MAHCs in the air of buses and bus stations were 95.9 and 36.5 microg/m(3), respectively, of which toluene was the highest in all the sampling sites. Mean concentrations of all MAHCs in buses were statistically higher than those nearby bus stations (pbus drivers were 1.11x10(-5) and 4.00x10(-5), respectively, which were way above the limit set by USEPA. The health risk caused by MAHCs in bus microenvironment should be cautioned.

IEEE 1394/firewire a low cost, high speed, digital serial bus

Energy Technology Data Exchange (ETDEWEB)

Gaunt, R.

1997-05-01

Does the world need yet another 1/0 bus standard? If you need fast and cheap serial video communication, then the answer is yes. As technology advances, so too must data transport mechanisms advance. You can`t expect RS-232 to support real-time digital video, and if you can`t afford expensive professional serial video interfaces, (such as Sony`s Serial Digital Interface), Firewire may be a good solution. IEEE 1394, or commonly known as Firewire, is a general purpose serial bus that meets many of the 1/0 needs of today`s video and multimedia developers. For those of you who only read the first paragraph, here`s Firewire in a nutshell: It provides a guaranteed transfer rate of 10OMbps or 20OMbps of digital data (such as video direct from camera to computer), over an inexpensive, non-proprietary serial bus. Here is a list of its features.

Deadhead Trip Minimization in City Bus Transportation: A Real Life Application