WorldWideScience

Sample records for scavenging polyamide compositions

  1. Dynamic mechanical properties of toughened polyamide composites

    International Nuclear Information System (INIS)

    Alsewailem, Fares D.

    2008-01-01

    The effect of incorporating thermoplastic rubber on the dynamic mechanical properties, storage and loss moduli, of virgin and recycled glass-fiber-reinforced polyamide 66 has been investigated in this study. Styrene-Ethylene-Styrene and Ethylene-Propylene grafted with maleic anhydride were used as elastomers for toughening. Dynamic mechanical properties of the composites were examined by the rotational rhometry. Shear storage and loss moduli of recycled and virgin materials were measured against frequency. Also the variation of storage modulus of the virgin composites was measured against temperatures by conducting a series of torsion tests. Both dynamic storage and loss moduli of the composites were found to increase with increasing glass fiber and rubber contents. Recycled composites had lower values of dynamic modulus compared that of virgin composites; however by proper combining of fiber and rubber into the recycled material, its modulus fairly matches that of the virgin material. Addition of rubber to virgin composites causes a reduction in G' as temperature increases. Rubber, which acts as a stress concentrator, had a major effect on minimizing the overall modulus of the composites. The in G' versus temperature has been observed for all composites: however the temperature at which the transition G' occurs decreases with increasing rubber content. (author)

  2. Novel bio-composite of hydroxyapatite reinforced polyamide and polyethylene: Composition and properties

    International Nuclear Information System (INIS)

    Zuo Yi; Li Yubao; Li Jidong; Zhang Xiang; Liao Hongbing; Wang Yuanyuan; Yang Weihu

    2007-01-01

    A new bio-composite of hydroxyapatite reinforced polyamide 66 and high density polyethylene was prepared using melt mixing in a co-rotation twin screw extruder. Two series of composites with different composition were investigated using scanning electronic microscopy, mechanical testing, water absorption and infrared spectrometer. The results showed that the change of composition influenced significantly the properties of the composites by different mechanism. Polyethylene mixing with polyamide matrix induced different microstructure and adjusted water absorption and manufacturability. Hydrogen bonding between hydroxyapatite and the polar groups of polyamide improved the adhesion of interface

  3. Research on mechanical properties of carbon fiber /polyamide reinforced PP composites

    Science.gov (United States)

    Chen, Xinghui; Yu, Qiang; Liu, Lixia; Ji, Wenhua; Yang, Li; Fan, Dongli

    2017-10-01

    The polyamide composites reinforced by carbon fiber/polypropylene are produced by injection molding processing. The flow abilities and mechanical properties of the CF/PA/PP composite materials are studied by the fusion index instrument and the universal testing machine. The results show that with the content of carbon fiber/polyamide increase, the impact breaking strength and the tensile property of the composite materials increase, which is instructive to the actual injection production of polypropylene products.

  4. The Effect of Silane Coupling Agents on a Composite Polyamide-6/Talc

    Directory of Open Access Journals (Sweden)

    H. Wiebeck

    1998-12-01

    Full Text Available This paper evaluates the effect of the addition of silane agents on the mechanical properties (tensile strength, hardness and flexibility of the composite polyamide-6/talc. For this purpose, 30% and 40% of a talc with and without the addition of silane agents were incorporated into polyamide-6. Three kinds of silane agents were used, resulting in nine formulations. Comparing the experimental results, it is concluded that the silane agents improve the mechanical properties of the composite material.

  5. Influence of moisture absorption on properties of fiber reinforced polyamide 6 composites

    DEFF Research Database (Denmark)

    Raghavalu Thirumalai, Durai Prabhakaran; Løgstrup Andersen, Tom; Lystrup, Aage

    2011-01-01

    sensitive to moisture, and if PA6 is used as matrix material in a fiber composite, the properties of the fiber composite will depend on the moisture content of the material. At standard condition (23 °C and 50% RH) polyamide6 absorbs about 3 weight-% of water, whereas the PA6 material is dry right after...

  6. Applications of polyamide/cellulose fiber/wollastonite composites for microcellular injection molding

    Science.gov (United States)

    Herman Winata; Lih-Sheng Turng; Daniel F. Caulfield; Tom Kuster; Rick Spindler; Rod Jacobson

    2003-01-01

    In this study, a cellulose-fiber-reinforced Polyamide-6 (PA-6) composite, a hybrid composite (PA-6/cellulose/Wollastonite), and the neat PA-6 resin were injection molded into ASTM test–bar samples with conventional and microcellular injection molding. The impact and tensile strengths of molded samples were measured and the Scanning Electron Microscopy (SEM) images were...

  7. Mechanical Characterization and Fractography of Glass Fiber/Polyamide (PA6) Composites

    DEFF Research Database (Denmark)

    Raghavalu Thirumalai, Durai Prabhakaran; Pillai, Saju; Charca, Samuel

    2015-01-01

    The mechanical properties of the glass fiber reinforced Polyamide (PA6) composites made by prepreg tapes and commingled yarns were studied by in-plane compression, short-beam shear, and flexural tests. The composites were fabricated with different fiber volume contents (prepregs—47%, 55%, 60%, an...

  8. Scavenger

    DEFF Research Database (Denmark)

    2009-01-01

    Scavenger is one of the cyber foraging frameworks developed in the Locusts project. It has been released as open source software at http://code.google.com/p/scavenger-cf/......Scavenger is one of the cyber foraging frameworks developed in the Locusts project. It has been released as open source software at http://code.google.com/p/scavenger-cf/...

  9. Optimization of preparation conditions of polyamide thin film composite membrane for organic solvent nanofiltration

    International Nuclear Information System (INIS)

    Namvar-Mahboub, Mahdieh; Pakizeh, Majid

    2014-01-01

    Separation performance of polyamide composite membranes is affected by several parameters during formation of thin upper layer via interfacial polymerization. We investigated the effect of various polyamide synthesis conditions on the performance of organic solvent resistant polyamide composite membranes through the model equations designed by 2-level fractional factorial design. The dewaxing solvent recovery was selected as separation process. Five factors were changed in two level includin; TMC concentration (0.05-0.1%), MPD concentration (1-2%), support immersion time in organic solution (2-4 min), support immersion time in aqueous solution (1-2 min), and curing temperature (70-80 .deg. C). The resultant equations showed 93.48% and 94.82% of the variability (R 2 adj ) in data used to fit oil rejection and permeate flux models, respectively. The analysis of variance revealed that both models were high significant. It was also observed that TMC concentration, MPD concentration and immersion time in TMC have more pronounced effect on the oil rejection and permeate flux than other factors and interactions. Optimal polyamide preparation conditions were obtained using multiple response method for 94% oil rejection as target value. According to the results, the best value of permeate flux (8.86 l/(m 2 ·h)) was found at TMC concentration of 0.1%, MPD concentration of 1.94%, immersion time in TMC of 3.88 min, immersion time in MPD of 1.95 min and curing temperature of 71.96 .deg. C with desirability factor of 1

  10. Polyamide 6/nickel ferrite composites: morphological and structural evaluation; Compositos poliamida 6 /ferrita de niquel: avaliacao morfologica e estrutural

    Energy Technology Data Exchange (ETDEWEB)

    Menezes, P.C.F.; Santos, P.T.A.; Wanderley, A.S.D.; Costa, A.C.F.M.; Araujo, E.M., E-mail: patricia.fernandes24@hotmail.com [Universidade Federal de Campina Grande (UFCG), Campina Grande, PB (Brazil). Unidade Academica de Engenharia de Materiais

    2011-07-01

    This study aims to evaluate the influence of particle size of the load on the structure and morphology of polyamide composite 6/ferrita nickel. To obtain the composite, the polyamide 6 was previously vacuum dried at 80 ° C/48h to eliminate moisture, and then the load was incorporated as powders and as synthesized after calcination at 900°C in the mass concentration of 50%. Subsequently, the mixture was compressed using three tons to obtain the composites, which were characterized by XRD and SEM. XRD results showed the characteristic peaks of polyamide 6 and ferrite. An increase in crystallinity was observed for the composite loaded calcined at 900° C. SEM results showed a good dispersion of nickel ferrite loading in the matrix, the presence of larger clusters and evenly distributed load for the composite calcined at 900 ° C. (author)

  11. Morphology and transport in biodegradable polymer compositions based on poly(3-hydroxybutyrate) and polyamide 54C

    Energy Technology Data Exchange (ETDEWEB)

    Zhul' kina, A. L.; Ivantsova, E. L.; Filatova, A. G.; Kosenko, R. Yu.; Gumargalieva, K. Z.; Iordanskii, A. L., E-mail: iordan@chph.ras.ru [Russian Academy of Sciences, Semenov Institute of Chemical Physics (Russian Federation)

    2009-05-15

    Complex investigation of the equilibrium sorption of water, diffusive transport of antiseptic, and morphology of mixed compositions based on polyoxybutirate and polyamide resin 54C has been performed to develop and analyze new biodegradable polymer compositions for controlled release of medicinal substances. Samples of mixtures were prepared by two methods: pressing under pressure and solvent evaporation from a polymer solution. The samples were compared and their morphology was analyzed by scanning electron microscopy. It is shown that the component ratio in the obtained mixtures affects their morphological, transport, and sorption characteristics.

  12. Morphology and transport in biodegradable polymer compositions based on poly(3-hydroxybutyrate) and polyamide 54C

    International Nuclear Information System (INIS)

    Zhul'kina, A. L.; Ivantsova, E. L.; Filatova, A. G.; Kosenko, R. Yu.; Gumargalieva, K. Z.; Iordanskii, A. L.

    2009-01-01

    Complex investigation of the equilibrium sorption of water, diffusive transport of antiseptic, and morphology of mixed compositions based on polyoxybutirate and polyamide resin 54C has been performed to develop and analyze new biodegradable polymer compositions for controlled release of medicinal substances. Samples of mixtures were prepared by two methods: pressing under pressure and solvent evaporation from a polymer solution. The samples were compared and their morphology was analyzed by scanning electron microscopy. It is shown that the component ratio in the obtained mixtures affects their morphological, transport, and sorption characteristics.

  13. COMPOSITE POLYMERICADDITIVESDESIGNATED FORCONCRETEMIXES BASED ONPOLYACRYLATES, PRODUCTS OF THERMAL DECOMPOSITION OF POLYAMIDE-6 AND LOW-MOLECULAR POLYETHYLENE

    Directory of Open Access Journals (Sweden)

    Polyakov Vyacheslav Sergeevich

    2012-07-01

    4 the optimal composite additive that increases the time period of stiffening of the cement grout , improves the water resistance and the compressive strength of concrete, represents the composition of polyacrylates and polymethacrylates, products of thermal decomposition of polyamide-6 and low-molecular polyethylene in the weight ratio of 1:1:0.5.

  14. Modelling mechanical properties of the multilayer composite materials with the polyamide core

    Directory of Open Access Journals (Sweden)

    Talaśka Krzysztof

    2018-01-01

    Full Text Available Due to the wide range of application for belt conveyors, engineers look for many different combinations of mechanical properties of conveyor and transmission belts. It can be made by creating multilayer or fibre reinforced composite materials from base thermoplastic or thermosetting polymers. In order to gain high strength with proper elasticity and friction coefficient, the core of the composite conveyor belt is made of polyamide film core, which can be combined with various types of polymer fabrics, films or even rubbers. In this paper authors show the complex model of multilayer composite belt with the polyamide core, which can be used in simulation analyses. The following model was derived based on the experimental research, which consisted of tensile, compression and shearing tests. In order to achieve the most accurate model, proper simulations in ABAQUS were made and then the results were compared with empirical mechanical characteristics of a conveyor belt. The main goal of this research is to fully describe the perforation process of conveyor and transmission belts for vacuum belt conveyors. The following model will help to develop design briefs for machines used for mechanical perforation.

  15. Environmental effect on the mechanical properties of commingled-yarn-based carbon fibre/polyamide 6 composites

    DEFF Research Database (Denmark)

    Raghavalu Thirumalai, Durai Prabhakaran; Toftegaard, Helmuth Langmaack

    2014-01-01

    The main objective of this experimental investigation was to evaluate the changes from accelerated ageing on selected properties of carbon fibre/polyamide 6 composites based on hybrid yarns. In this study, two types of mechanical tests were performed to measure the environmental influence...... on the material properties. They are three-point bending to measure the flexural strength and stiffness, and short beam three-point bending to measure the interlaminar shear strength. The 10-mm-thick quasi-isotropic carbon fibre/polyamide 6 composites with 52% volume fraction of carbon fibre to be tested were...... temperature. The interlaminar shear strength values also drop to about 75% at both −45 and 115. Extreme temperatures and long-time exposure to humidity of quasi-isotropic carbon fibre/polyamide 6 laminates can thus reduce the bending stiffness and strength by up to 35% and the interlaminar shear strength...

  16. Mercuric iodide composite films using polyamide, polycarbonate and polystyrene fabricated by casting

    International Nuclear Information System (INIS)

    Ugucioni, J.C.; Ghilardi Netto, T.; Mulato, M.

    2010-01-01

    Mercuric iodide (HgI 2 ) composite films were obtained by using the casting technique. Insulator polymers such as polyamide, polycarbonate and polystyrene were mixed to HgI 2 crystallites forming a final sub-millimeter thick self-standing film. Fabrication temperature varied from 10 to 100 o C, and total fabrication time reached at most 5 min. The larger the fabrication temperature, the thinner the film and the smaller its electrical resistivity. Electrical characterization was performed in the dark, under UV illumination and under mammographic X-ray exposure. The final properties of the films are discussed and related to fabrication conditions. The optimized composite film might be a better candidate for use as X-ray detector for medical imaging, in place of the single HgI 2 crystalline device.

  17. Effects of surface coating process conditions on the water permeation and salt rejection properties of composite polyamide reverse osmosis membranes

    KAUST Repository

    Louie, Jennifer Sarah; Pinnau, Ingo; Reinhard, Martin

    2011-01-01

    are impacted by the coating process steps, and investigates how such effects could contribute to lower water flux. On one hand, simply pre-soaking dry aromatic polyamide composite membranes in aliphatic alcohols results in a significant increase in water flux

  18. Surface modification of polyamide thin film composite membrane by coating of titanium dioxide nanoparticles

    Directory of Open Access Journals (Sweden)

    Thu Hong Anh Ngo

    2016-12-01

    Full Text Available In this paper, the coating of TiO2 nanoparticles onto the surface of a polyamide thin film composite nanofiltration membrane has been studied. Changes in the properties and separation performance of the modified membranes were systematically characterized. The experimental results indicated that the membrane surface hydrophilicity was significantly improved by the presence of the coated TiO2 nanoparticles with subsequent UV irradiation. The separation performance of the UV-irradiated TiO2-coated membranes was improved with a great enhancement of flux and a very high retention for removal of residual dye in an aqueous feed solution. The antifouling property of the UV-irradiated TiO2-coated membranes was enhanced with higher maintained flux ratios and lower irreversible fouling factors compared with an uncoated membrane.

  19. Tensile fracture behaviors of T-ZnOw/polyamide 6 composites

    International Nuclear Information System (INIS)

    Shi Jing; Wang Yong; Liu Li; Bai Hongwei; Wu Jun; Jiang Chongxi; Zhou, Zuowan

    2009-01-01

    As a part of serial work about the application of tetra-needle-shaped zinc oxide whisker (T-ZnOw) in polymer composites, this work is focused on the crystallization and tensile fracture behaviors of T-ZnOw/polyamide 6 (T-ZnOw/PA6) composites. Our results show that the addition of T-ZnOw improves the composites tensile strength greatly. For virgin PA6, the stress-strain curve exhibits double-yielding phenomenon. Surface modified T-ZnOw reinforced PA6 composites exhibit higher yield stress and smaller strain-to-fracture compared with virgin PA6. The morphologies of tensile-fractured surfaces show that, addition of T-ZnOw changes the fracture mode from crazing-tearing/brittle fracture mode of virgin PA6 into fibrillation/brittle fracture mode of PA6 composites. Especially, the fracture process of T-ZnOw in composites during the tensile test has been characterized by scanning electronic microscope (SEM) and the corresponding reinforcement mechanism has been discussed.

  20. The influence of sterilisation on the macromechanical properties of polyamide fibre-reinforced PDMS composites for orthopaedic applications

    Czech Academy of Sciences Publication Activity Database

    Sedláček, R.; Suchý, Tomáš; Sucharda, Zbyněk; Balík, Karel; Sochor, M.; Šepitka, J.; Lukeš, J.

    2012-01-01

    Roč. 15, S1 (2012), s. 91-92 ISSN 1025-5842. [Congress of the Société de Biomécanique /37./. Toulouse, 16.10.2012-19.10.2012] R&D Projects: GA ČR(CZ) GAP108/10/1457 Institutional research plan: CEZ:AV0Z30460519 Keywords : composite material * polymer matrix * polyamide Subject RIV: JI - Composite Materials Impact factor: 1.393, year: 2012

  1. Preliminary biocompatible evaluation of nano-hydroxyapatite/polyamide 66 composite porous membrane

    Directory of Open Access Journals (Sweden)

    Yili Qu

    2010-06-01

    Full Text Available Yili Qu1,3, Ping Wang1,3, Yi Man1, Yubao Li2, Yi Zuo2, Jidong Li21State Key Laboratory of Oral Diseases, Sichuan University, Chengdu 610064, China; 2Research Center for Nano-Biomaterials, Analytical and Testing Center, Sichuan University, Chengdu 610064, China; 3These authors contributed equally to this workAbstract: Nano-hydroxyapatite/polyamide 66 (nHA/PA66 composite with good bioactivity and osteoconductivity was employed to develop a novel porous membrane with asymmetric structure for guided bone regeneration (GBR. In order to test material cytotoxicity and to investigate surface-dependent responses of bone-forming cells, the morphology, proliferation, and cell cycle of bone marrow stromal cells (BMSCs of rats cultured on the prepared membrane were determined. The polygonal and fusiform shape of BMSCs was observed by scanning electronic microscopy (SEM. The proliferation of BMSCs cultured on nHA/PA66 membrane tested by the MTT method (MTT: [3-{4,5-dimethylthiazol-2yl}-2,5-diphenyl-2H-tetrazoliumbromide] was higher than that of negative control groups for 1 and 4 days’ incubation and had no significant difference for 7 and 11 days’ culture. The results of cell cycle also suggested that the membrane has no negative influence on cell division. The nHA/PA66 membranes were then implanted into subcutaneous sites of nine Sprague Dawley rats. The wounds and implant sites were free from suppuration and necrosis in all periods. All nHA/PA66 membranes were surrounded by a fibrous capsule with decreasing thickness 1 to 8 weeks postoperatively. In conclusion, the results of the in vitro and in vivo studies reveal that nHA/PA66 membrane has excellent biocompatibility and indicate its use in guided tissue regeneration (GTR or GBR.Keywords: hydroxyapatite/polyamide, barrier membrane, biocompatibility, guided bone regeneration

  2. Tribological and mechanical behaviors of polyamide 6/glass fiber composite filled with various solid lubricants.

    Science.gov (United States)

    Li, Duxin; Xie, Ying; Li, Wenjuan; You, Yilan; Deng, Xin

    2013-01-01

    The effects of polytetrafluoroethylene (PTFE), graphite, ultrahigh molecular weight polyethylene (UHMWPE), and their compounds on mechanical and tribological properties of glass-fiber-reinforced polyamide 6 (PA6/GF) were studied. The polymeric materials were blended using twin-screw extruder and subsequently injection molded for test samples. Mechanical properties were investigated in terms of hardness, tensile strength, and impact strength. Friction and wear experiments were run under ambient conditions at a rotating speed of 200 rpm and load of 100 N. The morphologies of the worn surfaces were also observed with scanning electron microscope. The results showed that graphite could increase the tensile strength of PA6/GF-15 composite, but the material became soft. Graphite/UHMWPE complex solid lubricants were effective in increasing the already high impact strength of PA6/GF-15 composite. 5% PTFE gave the maximum reduction in the coefficient of friction. However, PTFE/UHMWPE complex solid lubricants were the best choice for improving both friction and wear behaviors due to the lower friction coefficient and mass wear rate. Moreover, the worn surface of PA6 composites revealed that adhesive wear, abrasive wear, and fatigue wear occurred in this study.

  3. Tribological and Mechanical Behaviors of Polyamide 6/Glass Fiber Composite Filled with Various Solid Lubricants

    Directory of Open Access Journals (Sweden)

    Duxin Li

    2013-01-01

    Full Text Available The effects of polytetrafluoroethylene (PTFE, graphite, ultrahigh molecular weight polyethylene (UHMWPE, and their compounds on mechanical and tribological properties of glass-fiber-reinforced polyamide 6 (PA6/GF were studied. The polymeric materials were blended using twin-screw extruder and subsequently injection molded for test samples. Mechanical properties were investigated in terms of hardness, tensile strength, and impact strength. Friction and wear experiments were run under ambient conditions at a rotating speed of 200 rpm and load of 100 N. The morphologies of the worn surfaces were also observed with scanning electron microscope. The results showed that graphite could increase the tensile strength of PA6/GF-15 composite, but the material became soft. Graphite/UHMWPE complex solid lubricants were effective in increasing the already high impact strength of PA6/GF-15 composite. 5% PTFE gave the maximum reduction in the coefficient of friction. However, PTFE/UHMWPE complex solid lubricants were the best choice for improving both friction and wear behaviors due to the lower friction coefficient and mass wear rate. Moreover, the worn surface of PA6 composites revealed that adhesive wear, abrasive wear, and fatigue wear occurred in this study.

  4. Multifunctional glass fiber/polyamide composites with thermal energy storage/release capability

    Directory of Open Access Journals (Sweden)

    G. Fredi

    2018-04-01

    Full Text Available Thermoplastic composite laminates with thermal energy storage (TES capability were prepared by combining a glass fabric, a polyamide 12 (PA12 matrix and two different phase change materials (PCMs, i.e. a paraffinic wax microencapsulated in melamine-formaldehyde shells and a paraffin shape stabilized with carbon nanotubes. The melt flow index of the PA12/PCM blends decreased with the PCM concentration, especially in the systems with shape stabilized wax. Differential scanning calorimetry showed that, for the matrices with microcapsules, the values of enthalpy were approximately the 70% of the theoretical values, which was attributed to the fracture of some microcapsules. Nevertheless, most of the energy storage capability was preserved. On the other hand, much lower relative enthalpy values were measured on the composites with shape stabilized wax, due to a considerable paraffin leakage or degradation. The subsequent characterization of the glass fabric laminates highlighted that the fiber and void volume fractions were comparable for all the laminates except for that with the higher amount of shape stabilized wax, where the high viscosity of the matrix led to a low fiber volume fraction and higher void content. The mechanical properties of the laminates were only slightly impaired by PCM addition, while a more sensible drop of the elastic modulus, of the stress at break and of the interlaminar shear strength could be observed in the shape stabilized wax systems.

  5. Utilization of rice husk ash as filler for polyamide 6 and ionizing radiation effect studies on this composite

    International Nuclear Information System (INIS)

    Ferro, Waldir Pedro

    2009-01-01

    In order to improve the dimensional stability, as well as, electrical, mechanical and thermal properties of polymers, new filler to this purpose has been developed. The mos applied filler to propitiate the features previously mentioned are the glass and carbon fibers, the mineral filler as the calcium carbonate, the talc and the micro glass sphere. The main aim of this work was to study the rice husk ash as filler for polyamide 6 and ionizing radiation effect studies on this composite, irradiated by electron beam at different doses, since it is constituted of at least 90% of silicon dioxide, and compared with the talc which is the most applied mineral filler. This comparison was made from a compound made through the refined rice husk ash and the polyamide 6 (PA 6), which is one of the main engineering plastic with applications in several productive areas. The samples were injected and irradiated in a electron accelerator. Afterwards, their mechanical and thermal properties were measured. It was also inject automotive parts to verify the processing of the PA 6 with CCA. The results showed that the use of the rice husk ash as filler for polyamide 6 composite is technically and economically viable. The irradiation of the studied composite (PA 6 with 30% of rice husk ash) did not provide any improvement for the mechanical and thermal properties previously appraised. (author)

  6. Reactive processing of textile-natural fiber reinforced anionic polyamide-6 composites

    International Nuclear Information System (INIS)

    Kan, Ze; Chen, Peng; Liu, Zhengying; Feng, Jianmin; Yang, Mingbo

    2015-01-01

    Nowadays natural fiber, used in reinforced composites, is widely concerned. However, no natural fiber reinforced reactive thermoplastic polymer grades had been prepared so far. Through our studies, it was demonstrated that there was a severe retardation and discoloration occurred in the reactive processing between anionic polyamide-6 (APA-6) and natural fiber, which result in incomplete polymerization when put together. In order to solve the problem, two methods were adopted in this paper, which are fiber pretreatment and usage of a new-style initiator called caprolactam magnesium bromide. The former is to remove sizing agent and impurities on the surface of fiber, and the latter is to weaken the side reactions between APA-6 and natural fiber by the nature of its lower reactivity and weaker alkaline. In cooperation with both methods, the severe retardation and discoloration had been improved significantly, so that the polymerization of APA-6 in natural fiber was occurred smoothly. Following textile-natural fiber reinforced APA-6 composites with an average thickness of 2.5 mm and a fiber volume content of 50% was prepared by vacuum assisted resin transfer molding (VARTM). The soxhlet extraction, dilute solution viscometry and differential scanning calorimeter (DSC) measurements respectively suggested the degree of conversion, viscosity-average molar mass and crystallization of composites was up to 94%, 11.3×104 and 50%. Remarkable improvement of mechanical properties were achieved through dynamic mechanical analysis (DMA), tensile and three-point bending test. Favorable interfacial adhesion and wettability were revealed by scanning electron microscopy (SEM) observation. Therefore, all of the above good performance make this new-style and environmentally friendly composites have broad application prospects

  7. Reactive processing of textile-natural fiber reinforced anionic polyamide-6 composites

    Science.gov (United States)

    Kan, Ze; Chen, Peng; Liu, Zhengying; Feng, Jianmin; Yang, Mingbo

    2015-05-01

    Nowadays natural fiber, used in reinforced composites, is widely concerned. However, no natural fiber reinforced reactive thermoplastic polymer grades had been prepared so far. Through our studies, it was demonstrated that there was a severe retardation and discoloration occurred in the reactive processing between anionic polyamide-6 (APA-6) and natural fiber, which result in incomplete polymerization when put together. In order to solve the problem, two methods were adopted in this paper, which are fiber pretreatment and usage of a new-style initiator called caprolactam magnesium bromide. The former is to remove sizing agent and impurities on the surface of fiber, and the latter is to weaken the side reactions between APA-6 and natural fiber by the nature of its lower reactivity and weaker alkaline. In cooperation with both methods, the severe retardation and discoloration had been improved significantly, so that the polymerization of APA-6 in natural fiber was occurred smoothly. Following textile-natural fiber reinforced APA-6 composites with an average thickness of 2.5 mm and a fiber volume content of 50% was prepared by vacuum assisted resin transfer molding (VARTM). The soxhlet extraction, dilute solution viscometry and differential scanning calorimeter (DSC) measurements respectively suggested the degree of conversion, viscosity-average molar mass and crystallization of composites was up to 94%, 11.3×104 and 50%. Remarkable improvement of mechanical properties were achieved through dynamic mechanical analysis (DMA), tensile and three-point bending test. Favorable interfacial adhesion and wettability were revealed by scanning electron microscopy (SEM) observation. Therefore, all of the above good performance make this new-style and environmentally friendly composites have broad application prospects.

  8. Triclosan-immobilized polyamide thin film composite membranes with enhanced biofouling resistance

    Science.gov (United States)

    Park, Sang-Hee; Hwang, Seon Oh; Kim, Taek-Seung; Cho, Arah; Kwon, Soon Jin; Kim, Kyoung Taek; Park, Hee-Deung; Lee, Jung-Hyun

    2018-06-01

    We report on a strategy to improve biofouling resistance of a polyamide (PA) thin-film composite (TFC) reverse osmosis (RO) membrane via chemically immobilizing triclosan (TC), known as a common organic biocide, on its surface. To facilitate covalent attachment of TC on the membrane surface, TC was functionalized with amine moiety to prepare aminopropyl TC. Then, the TC-immobilized TFC (TFC-TC) membranes were fabricated through a one-step amide formation reaction between amine groups of aminopropyl TC and acyl chloride groups present on the PA membrane surface, which was confirmed by high-resolution XPS. Strong stability of the immobilized TC was also confirmed by a hydraulic washing test. Although the TFC-TC membrane showed slightly reduced separation performance compared to the pristine control, it still maintained a satisfactory RO performance level. Importantly, the TFC-TC membrane exhibited excellent antibacterial activity against both gram negative (E. coli and P. aeruginosa) and gram positive (S. aureus) bacteria along with greatly enhanced resistance to biofilm formation. Our immobilization approach offers a robust and relatively benign strategy to control biofouling of functional surfaces, films and membranes.

  9. Spatial complexity of carcass location influences vertebrate scavenger efficiency and species composition.

    Science.gov (United States)

    Smith, Joshua B; Laatsch, Lauren J; Beasley, James C

    2017-08-31

    Scavenging plays an important role in shaping communities through inter- and intra-specific interactions. Although vertebrate scavenger efficiency and species composition is likely influenced by the spatial complexity of environments, heterogeneity in carrion distribution has largely been disregarded in scavenging studies. We tested this hypothesis by experimentally placing juvenile bird carcasses on the ground and in nests in trees to simulate scenarios of nestling bird carrion availability. We used cameras to record scavengers removing carcasses and elapsed time to removal. Carrion placed on the ground was scavenged by a greater diversity of vertebrates and at > 2 times the rate of arboreal carcasses, suggesting arboreal carrion may represent an important resource to invertebrate scavengers, particularly in landscapes with efficient vertebrate scavenging communities. Nonetheless, six vertebrate species scavenged arboreal carcasses. Rat snakes (Elaphe obsolete), which exclusively scavenged from trees, and turkey vultures (Cathartes aura) were the primary scavengers of arboreal carrion, suggesting such resources are potentially an important pathway of nutrient acquisition for some volant and scansorial vertebrates. Our results highlight the intricacy of carrion-derived food web linkages, and how consideration of spatial complexity in carcass distribution (i.e., arboreal) may reveal important pathways of nutrient acquisition by invertebrate and vertebrate scavenging guilds.

  10. Effects of surface coating process conditions on the water permeation and salt rejection properties of composite polyamide reverse osmosis membranes

    KAUST Repository

    Louie, Jennifer Sarah

    2011-02-01

    The application of polymer surface coatings to improve the fouling resistance of reverse osmosis membranes tends to increase flow resistance across the membrane. This paper presents a systematic analysis on how membrane properties and performance are impacted by the coating process steps, and investigates how such effects could contribute to lower water flux. On one hand, simply pre-soaking dry aromatic polyamide composite membranes in aliphatic alcohols results in a significant increase in water flux, which is attributed to wetting of pores in the selective polyamide layer and to changes in the polymer structure. This flux increase was not readily reversible, based on a 300-h water permeation test. Conversely, drying a wetted membrane led to a decrease in water flux, which we hypothesize is caused by increased interchain hydrogen-bonding in the selective layer. This drop in water flux was not permanent; higher flux was observed if the same wetted/dried membrane was then re-soaked in ethanol prior to the water permeation experiment. An ethanol pre-soaking step also increased water flux of a PEBAX-coated membrane by nearly 70%. In contrast to the reduction in water flux caused by the specific treatment sequence of ethanol-swelling followed by drying, this same sequence actually increased gas transport. The eight- to ten-fold increase in Knudsen diffusion-based gas permeance after this pre-treatment was attributed to an increase in the number or size of membrane defects. © 2010 Elsevier B.V.

  11. Evaluation of Thermal and Thermomechanical Behaviour of Bio-Based Polyamide 11 Based Composites Reinforced with Lignocellulosic Fibres

    Directory of Open Access Journals (Sweden)

    Helena Oliver-Ortega

    2017-10-01

    Full Text Available In this work, polyamide 11 (PA11 and stone ground wood fibres (SGW were used, as an alternative to non-bio-based polymer matrices and reinforcements, to obtain short fibre reinforced composites. The impact of the reinforcement on the thermal degradation, thermal transitions and microstructure of PA11-based composites were studied. Natural fibres have lower degradation temperatures than PA11, thus, composites showed lower onset degradation temperatures than PA11, as well. The thermal transition and the semi-crystalline structure of the composites were similar to PA11. On the other hand, when SGW was submitted to an annealing treatment, the composites prepared with these fibres increased its crystallinity, with increasing fibre contents, compared to PA11. The differences between the glass transition temperatures of annealed and untreated composites decreased with the fibre contents. Thus, the fibres had a higher impact in the composites mechanical behaviour than on the mobility of the amorphous phase. The crystalline structure of PA11 and PA11-SGW composites, after annealing, was transformed to α’ more stable phase, without any negative impact on the properties of the fibres.

  12. Effects of hydrophilic solvent and oxidation resistance post surface treatment on molecular structure and forward osmosis performance of polyamide thin-film composite (TFC) membranes

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Qibo; Xu, Yangyu [School of Environment, Tsinghua University, Beijing 100084 (China); Shen, Jianquan [Beijing National Laboratory for Molecular Sciences (BNLMS), Key Laboratory of Green Printing, Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); Yang, Haijun, E-mail: yanghj@iccas.ac.cn [Beijing National Laboratory for Molecular Sciences (BNLMS), Key Laboratory of Green Printing, Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); Zhou, Lu, E-mail: zhoulu@tsinghua.edu.cn [School of Environment, Tsinghua University, Beijing 100084 (China)

    2015-11-30

    Graphical abstract: - Highlights: • NMP promotes swelling of polyamide, which enhances the TFC FO membrane water flux. • Electron-withdrawing carboxyl groups reduce the activity of polyamide molecules. • TMC and oxalic acid can improve the oxidation resistance properties of the FO membrane. • Oxalic acid and EDC improve the FO membrane separation performance significantly. - Abstract: In this article, novel hydrophilic solvents and antioxidants were used to post-treat aromatic polyamide thin-film composite (TFC) hollow fiber forward osmosis (FO) membranes. The effects of trimesoyl chloride (TMC) and oxalic acid on the structure of polyamide skin layer were investigated using ATR-FTIR and XPS analyses. Pure water flux and rejection of salts were detected using 2 M NaCl solution as draw solutions in FO processes. The results demonstrated that hydrophilic solvent N-methyl pyrrolidone (NMP) enhanced the water flux and kept a high salt retention of the TFC FO membrane. TMC and oxalic acid were both found to improve the oxidation resistance properties of the skin layer of TFC membrane because the electron-withdrawing carboxyl groups reduced the activity of polyamide molecular. The effects of the oxalic acid and carbodiimide on the molecular structures and the FO water flux of the polyamide TFC membranes were more marked than those of TMC. The novel TFC FO membrane treated by oxalic acid and 1-(3-dimethylaminopropyl)-3-ethylcarbodiimide hydrochloride (EDC) exhibited a high level of water flux (20.33 L m{sup −2} h{sup −1}), and the rates of salt rejection and salt reverse rejection were higher by 50% and 83%, respectively.

  13. Thermal and mechanical properties of polyamide 6/compatibilizer/clay nano composites

    International Nuclear Information System (INIS)

    Agrawal, P.; Brito, G.F.; Cunha, C.T.C.; Araujo, E.M.; Melo, T.J.A.

    2010-01-01

    In this work, the thermal and mechanical properties of Polyamide 6 (PA6)/compatibilizer/clay (CL20A) nanocomposites were investigated. The nanocomposites were prepared in a counter-rotating twin screw extruder at 240 deg C and 50 rpm, and characterized by X-Ray Diffraction (XRD), Thermogravimetry (TG) and mechanical properties. XRD results showed that when the clay is mixed with PA6, the clay peak is shifted to lower 2θ angles, indicating that PA6 was intercalated between the clay platelets. For PA6/compatibilizer/clay system, the results indicated that a nanocomposite with exfoliated structure was formed. TG results showed that the thermal stability of PA6/CL20A and PA6/compatibilizer/CL20A was higher than that of neat PA6. The mechanical properties results showed that the addition of the compatibilizer to PA6/CL20A substantially increased the impact strength and decreased the stiffness. (author)

  14. Vieillissement du polyamide 11 utilisé dans les conduites flexibles : influence de la composition du fluide transporté Influence of the Chemical Nature of the Environment on the Aging of Polyamide 11 Used for Offshore Flexible Pipes

    Directory of Open Access Journals (Sweden)

    Ubrich E.

    2006-11-01

    Full Text Available Le polyamide 11 est utilisé comme gaine d'étanchéité interne des conduites flexibles de transport de produits pétroliers. Dans certaines conditions d'utilisation, celui-ci subit une dégradation de ses propriétés mécaniques et physico-chimiques initiales. Des échanges de matières s'établissent entre le matériau et le fluide transporté : des composés constitutifs du fluide (eau, hydrocarbures peuvent être absorbés par le polyamide tandis que le principal additif du matériau (le plastifiant est extrait. Cette étude, entreprise pour déterminer l'influence de la composition du milieu chimique sur les propriétés du polyamide 11, a permis : 1 De développer une nouvelle méthode d'analyse des matières diffusant dans le polyamide 11. Le principe de cette méthode consiste à réaliser une thermodésorption des différentes matières présentes dans le polymère et à les analyser en ligne par spectrométrie de masse à moyenne résolution (résolution = 3000. Cette méthode permet l'analyse quantitative simultanée du plastifiant résiduel, de l'eau et des hydrocarbures absorbés ainsi que la détermination de la répartition par familles chimiques de ces hydrocarbures. 2 De proposer un modèle prédictif du vieillissement du polyamide 11 dans des milieux modèles constitués d'eau, d'une coupe gazole principalement aliphatique et d'une coupe gazole principalement aromatique. La composition de ces différents milieux de vieillissement a été choisie à l'aide d'un plan d'expériences appliqué aux mélanges. L'influence de l'eau sur les propriétés mécaniques (diminution de l'allongement à la rupture et physico-chimiques (diminution de la masse moléculaire moyenne et augmentation du taux de cristallinité a été mise en évidence. Par ailleurs, quel que soit le milieu de vieillissement, à 140°C, le plastifiant est extrait du polyamide. L'influence du milieu aromatique sur la plastification du matériau a été d

  15. Comparison of mechanical properties for polyamide 12 composite-based biomaterials fabricated by fused filament fabrication and injection molding

    Science.gov (United States)

    Rahim, Tuan Noraihan Azila Tuan; Abdullah, Abdul Manaf; Akil, Hazizan Md; Mohamad, Dasmawati

    2016-12-01

    The emergence of 3D printing technology known as fused filament fabrication (FFF) has offered the possibility of producing an anatomically accurate, patient specific implant with more affordable prices. The only weakness of this technology is related to incompatibility and lack of properties of current material to be applied in biomedical. Therefore, this study aims to develop a new, polymer composite-based biomaterial that exhibits a high processability using FFF technique, strong enough and shows acceptable biocompatibility, and safe for biomedical use. Polyamide 12 (PA12), which meets all these requirements was incorporated with two bioceramic fillers, zirconia and hydroxyapatite in order to improve the mechanical and bioactivity properties. The obtained mechanical properties were compared with injection-molded specimens and also a commercial biomedical product, HAPEXTM which is composed of hydroxyapatite and polyethylene. The yield strength and modulus of the PA12 composites increased steadily with increasing filler loading. Although the strength of printed PA12 composites were reduced compared with injection molded specimen, but still higher than HAPEXTM material. The higher surface roughness obtained by printed PA12 was expected to enhance the cell adhesion and provide better implant fixation.

  16. Bone plate composed of a ternary nano-hydroxyapatite/polyamide 66/glass fiber composite: biomechanical properties and biocompatibility.

    Science.gov (United States)

    Qiao, Bo; Li, Jidong; Zhu, Qingmao; Guo, Shuquan; Qi, Xiaotong; Li, Weichao; Wu, Jun; Liu, Yang; Jiang, Dianming

    2014-01-01

    An ideal bone plate for internal fixation of bone fractures should have good biomechanical properties and biocompatibility. In this study, we prepared a new nondegradable bone plate composed of a ternary nano-hydroxyapatite/polyamide 66/glass fiber (n-HA/PA66/GF) composite. A breakage area on the n-HA/PA66/GF plate surface was characterized by scanning electron microscopy. Its mechanical properties were investigated using bone-plate constructs and biocompatibility was evaluated in vitro using bone marrow-derived mesenchymal stem cells. The results confirmed that adhesion between the n-HA/PA66 matrix and the glass fibers was strong, with only a few fibers pulled out at the site of breakage. Fractures fixed by the n-HA/PA66/GF plate showed lower stiffness and had satisfactory strength compared with rigid fixation using a titanium plate. Moreover, the results with regard to mesenchymal stem cell morphology, MTT assay, Alizarin Red S staining, enzyme-linked immunosorbent assay, and reverse transcription polymerase chain reaction for alkaline phosphatase and osteocalcin showed that the n-HA/PA66/GF composite was suitable for attachment and proliferation of mesenchymal stem cells, and did not have a negative influence on matrix mineralization or osteogenic differentiation of mesenchymal stem cells. These observations indicate that the n-HA/PA66/GF plate has good biomechanical properties and biocompatibility, and may be considered a new option for internal fixation in orthopedic surgery.

  17. Modification of PSf/SPSf Blended Porous Support for Improving the Reverse Osmosis Performance of Aromatic Polyamide Thin Film Composite Membranes

    Directory of Open Access Journals (Sweden)

    Li-Fen Liu

    2018-06-01

    Full Text Available In this study, modification of polysulfone (PSf/sulfonated polysulfone (SPSf blended porous ultrafiltration (UF support membranes was proposed to improve the reverse osmosis (RO performance of aromatic polyamide thin film composite (TFC membranes. The synergistic effects of solvent, polymer concentration, and SPSf doping content in the casting solution were investigated systematically on the properties of both porous supports and RO membranes. SEM and AFM were combined to characterize the physical properties of the membranes, including surface pore natures (porosity, mean pore radius, surface morphology, and section structure. A contact angle meter was used to analyze the membrane surface hydrophilicity. Permeate experiments were carried out to evaluate the separation performances of the membranes. The results showed that the PSf/SPSf blended porous support modified with 6 wt % SPSf in the presence of DMF and 14 wt % PSf had higher porosity, bigger pore diameter, and a rougher and more hydrophilic surface, which was more beneficial for fabrication of a polyamide TFC membrane with favorable reverse osmosis performance. This modified PSf/SPSf support endowed the RO membrane with a more hydrophilic surface, higher water flux (about 1.2 times, as well as a slight increase in salt rejection than the nascent PSf support. In a word, this work provides a new facile method to improve the separation performance of polyamide TFC RO membranes via the modification of conventional PSf porous support with SPSf.

  18. Structural and morphological characteristics of composite: polyamide 6/ferrite nickel; Caracteristicas morfologicas e estruturais do composito: poliamida 6/ferrita de niquel

    Energy Technology Data Exchange (ETDEWEB)

    Fernandes, P.C.; Santos, P.T.A.; Silva, T.R.G.; Araujo, E.M.; Costa, A.C.F.M., E-mail: patricia.fernandes24@hotmail.co [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais

    2010-07-01

    This study aims to evaluate the structural and morphological characteristics of a composite polyamide 6 with 50% loading of nickel ferrite. The ferrite was obtained by combustion synthesis and calcined in muffle furnace at 700 deg C. The polymer matrix was previously dried in vacuum oven at 80 deg C / 48 h to eliminate moisture. The composites were characterized by XRD and SEM. XRD results show the incorporation of cargo in the matrix, and that increasing temperature led to a considerable increase in crystallinity. The particle size of the load in the matrix was changed by increasing temperature. (author)

  19. A novel method based on selective laser sintering for preparing high-performance carbon fibres/polyamide12/epoxy ternary composites

    Science.gov (United States)

    Zhu, Wei; Yan, Chunze; Shi, Yunsong; Wen, Shifeng; Liu, Jie; Wei, Qingsong; Shi, Yusheng

    2016-09-01

    A novel method based on selective laser sintering (SLS) process is proposed for the first time to prepare complex and high-performance carbon fibres/polyamide12/epoxy (CF/PA12/EP) ternary composites. The procedures are briefly described as follows: prepare polyamide12 (PA12) coated carbon fibre (CF) composite powder; build porous green parts by SLS; infiltrate the green parts with high-performance thermosetting epoxy (EP) resin; and finally cure the resin at high temperature. The obtained composites are a ternary composite system consisting of the matrix of novolac EP resin, the reinforcement of CFs and the transition thin layer of PA12 with a thickness of 595 nm. The SEM images and micro-CT analysis prove that the ternary system is a three-dimensional co-continuous structure and the reinforcement of CFs are well dispersed in the matrix of EP with the volume fraction of 31%. Mechanical tests show that the composites fabricated by this method yield an ultimate tensile strength of 101.03 MPa and a flexural strength of 153.43 MPa, which are higher than those of most of the previously reported SLS materials. Therefore, the process proposed in this paper shows great potential for manufacturing complex, lightweight and high-performance CF reinforced composite components in aerospace, automotive industries and other areas.

  20. Reactive microencapsulation of carbon allotropes in polyamide shell-core structures and their transformation in hybrid composites with tailored electrical properties

    Directory of Open Access Journals (Sweden)

    F. Oliveira

    2016-02-01

    Full Text Available Polyamide 6 microcapsules (PAMC loaded with 2–10 wt% of different carbon allotropes: carbon black, multiwalled carbon nanotubes, carbon nanofibers and graphite were synthesized via activated anionic polymerization (AAROP of ε-caprolactam in solution performed in the presence of the respective micro- or nanosized loads. The forming high-molecular weight microporous PAMC showed typical diameters of 15–35 µm, the filler particles being entrapped in the core as proven by microscopy methods. The melt processing of the loaded microcapsules produced PA6/C-filler hybrid thermoplastic composites with homogeneous distribution of one or two C-fillers even at loads of up to 10% without any functionalization. The crystalline structure of all PAMC and molded composites was studied by thermal and X-ray diffraction methods focusing on possible structure modification during the transition from PAMC to molded plates. Mechanical tests in tension and electrical conductivity measurements showed that transforming loaded PAMC into composites by melt processing could be a facile and rapid method to fabricate polyamide composites with improved mechanical performance and tailored electrical and dielectric properties.

  1. Hydrolytic Decomposition in a Polyamide/PDMS Composite for Orthopaedic Usage

    Czech Academy of Sciences Publication Activity Database

    Sochor, M.; Balík, Karel; Sucharda, Zbyněk; Suchý, Tomáš; Sedláček, R.

    2011-01-01

    Roč. 14, č. 103 (2011), s. 2-3 ISSN 1429-7248 R&D Projects: GA ČR(CZ) GAP108/10/1457 Institutional research plan: CEZ:AV0Z30460519 Keywords : composite * hydrolic decomposition * orthopaedics Subject RIV: BO - Biophysics http://www.biomat.krakow.pl/gazeta/archiwum/103.pdf

  2. Evaluation of Radical Scavenging Activity of Sempervivum tectorum and Corylus avellana Extracts with Different Phenolic Composition.

    Science.gov (United States)

    Alberti, Ágnes; Riethmüller, Eszter; Béni, Szabolcs; Kéry, Ágnes

    2016-04-01

    Semnpervivum tectorum L. and Corylus avellana L. are traditional herbal remedies exhibiting antioxidant activity and representing diverse phenolic composition. The aim of this study was to reveal the contribution of certain compounds to total radical scavenging activity by studying S. tectorum and C. avellana extracts prepared with solvents of different selectivity for diverse classes of phenolics. Antioxidant activity of S. tectorum and C. avellana samples was determined in the ABTS and DPPH radical scavenging assays, and phenolic composition was evaluated by high-performance liquid chromatography/electrospray ionization tandem mass spectrometry (HPLC-ESI-MS/MS). Correlations between antioxidant activity and phenolic content of houseleek extracts have been revealed. Significant differences regarding antioxidant activity have been shown between S. tectorum 80% (v/v) methanol extract and its fractions. Additionally, synergism among the constituents present together in the whole extract was assumed. Significantly higher radical scavenging activity of hazel extracts has been attributed to the differences in phenolic composition compared with houseleek extracts.

  3. Polyamide Thin-Film Composite Membranes for Potential Raw Biogas Purification: Experiments and Modelling.

    Czech Academy of Sciences Publication Activity Database

    Šimčík, Miroslav; Růžička, Marek; Kárászová, Magda; Sedláková, Zuzana; Vejražka, Jiří; Veselý, M.; Čapek, P.; Friess, K.; Izák, Pavel

    2016-01-01

    Roč. 167, JUL 14 (2016), s. 163-173 ISSN 1383-5866 R&D Projects: GA ČR GA14-12695S; GA TA ČR TE01020080; GA MŠk(CZ) LD13018; GA MŠk LH14006 Institutional support: RVO:67985858 Keywords : thin film composite membrane * biogas membrane separation * transport modeling Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 3.359, year: 2016

  4. Tribological properties of solid lubricants filled glass fiber reinforced polyamide 6 composites

    International Nuclear Information System (INIS)

    Li, Du-Xin; You, Yi-Lan; Deng, Xin; Li, Wen-Juan; Xie, Ying

    2013-01-01

    Highlights: ► The tribological properties of GF/PA6 improved by the incorporation of PTFE. ► PTFE and UHMWPE exhibited a synergism effect on reducing friction coefficient. ► Solid lubricants enlarged the range of applied velocity for GF/PA6 composite. - Abstract: The main purpose of this paper is to further optimize the tribological properties of the glass fiber reinforced PA6 (GF/PA6,15/85 by weight) for high performance friction materials using single or combinative solid lubricants such as Polytetrafluroethylene (PTFE), ultra-high molecular weight polyethylene (UHMWPE) and the combination of both of them. Various polymer blends, where GF/PA6 acts as the polymer matrix and solid lubricants as the dispersed phase were prepared by injection molding. The tribological properties of these materials and the synergism as a result of the incorporation of both PTFE and UHMWPE were investigated. The results showed that, at a load of 40 N and a velocity of 200 rpm, PTFE was effective in improving the tribological capabilities of matrix material. On the contrary, UHMWPE was not conductive to maintain the structure integrity of GF/PA6 composite and harmful to the friction and wear properties. The combination of PTFE and UHMWPE showed synergism on further reducing the friction coefficient of the composites filled with either PTFE or UHMWPE only. Effects of load and velocity on tribological behavior were also discussed. To further understand the wear mechanism, the worn surfaces were examined by scanning electron microscopy

  5. Exploring the structure-properties relationships of novel polyamide thin film composite membranes

    DEFF Research Database (Denmark)

    Briceño, Kelly; Javakhishvili, Irakli; Guo, Haofei

    Polysulfone (PSU) is a material widely used in the fabrication of membranes for ultrafiltration and as a support for nanofiltration and reverse osmosis membranes. Interfacial polymerization usually combines amine and acid chloride monomers for the fabrication of thin film composite membranes[1......] . However, only few publications describe it’s usage for the modification of supports for the fabrication of ultrafiltration membranes [2]. This research focuses on the modification of PSU supports to produce new ultrafiltration membranes. The advantages of interfacial polymerization in the fabrication...... of UF membranes includes: Negatively charged PSF surfaces that could be less prone to biofouling Scale up process for the modification of PSU. An alternative to costly and technically challenging processes as in situ interfacial polymerization [3]....

  6. Comparison of biofouling mechanisms between cellulose triacetate (CTA) and thin-film composite (TFC) polyamide forward osmosis membranes in osmotic membrane bioreactors.

    Science.gov (United States)

    Wang, Xinhua; Zhao, Yanxiao; Yuan, Bo; Wang, Zhiwei; Li, Xiufen; Ren, Yueping

    2016-02-01

    There are two types of popular forward osmosis (FO) membrane materials applied for researches on FO process, cellulose triacetate (CTA) and thin film composite (TFC) polyamide. However, performance and fouling mechanisms of commercial TFC FO membrane in osmotic membrane bioreactors (OMBRs) are still unknown. In current study, its biofouling behaviors in OMBRs were investigated and further compared to the CTA FO membrane. The results indicated that β-D-glucopyranose polysaccharides and microorganisms accounted for approximately 77% of total biovolume on the CTA FO membrane while β-D-glucopyranose polysaccharides (biovolume ratio of 81.1%) were the only dominant biofoulants on the TFC FO membrane. The analyses on the biofouling structure implied that a tighter biofouling layer with a larger biovolume was formed on the CTA FO membrane. The differences in biofouling behaviors including biofoulants composition and biofouling structure between CTA and TFC FO membranes were attributed to different membrane surface properties. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Development of high-speed reactive processing system for carbon fiber-reinforced polyamide-6 composite: In-situ anionic ring-opening polymerization

    International Nuclear Information System (INIS)

    Kim, Sang-Woo; Seong, Dong Gi; Yi, Jin-Woo; Um, Moon-Kwang

    2016-01-01

    In order to manufacture carbon fiber-reinforced polyamide-6 (PA-6) composite, we optimized the reactive processing system. The in-situ anionic ring-opening polymerization of ε-caprolactam was utilized with proper catalyst and initiator for PA-6 matrix. The mechanical properties such as tensile strength, inter-laminar shear strength and compressive strength of the produced carbon fiber-reinforced PA-6 composite were measured, which were compared with the corresponding scanning electron microscope (SEM) images to investigate the polymer properties as well as the interfacial interaction between fiber and polymer matrix. Furthermore, kinetics of in-situ anionic ring-opening polymerization of ε-caprolactam will be discussed in the viewpoint of increasing manufacturing speed and interfacial bonding between PA-6 matrix and carbon fiber during polymerization.

  8. Development of high-speed reactive processing system for carbon fiber-reinforced polyamide-6 composite: In-situ anionic ring-opening polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sang-Woo; Seong, Dong Gi; Yi, Jin-Woo; Um, Moon-Kwang [Composites Research Division, Korea Institute of Materials Science (KIMS), Changwon, Gyeongnam, 642–831 (Korea, Republic of)

    2016-05-18

    In order to manufacture carbon fiber-reinforced polyamide-6 (PA-6) composite, we optimized the reactive processing system. The in-situ anionic ring-opening polymerization of ε-caprolactam was utilized with proper catalyst and initiator for PA-6 matrix. The mechanical properties such as tensile strength, inter-laminar shear strength and compressive strength of the produced carbon fiber-reinforced PA-6 composite were measured, which were compared with the corresponding scanning electron microscope (SEM) images to investigate the polymer properties as well as the interfacial interaction between fiber and polymer matrix. Furthermore, kinetics of in-situ anionic ring-opening polymerization of ε-caprolactam will be discussed in the viewpoint of increasing manufacturing speed and interfacial bonding between PA-6 matrix and carbon fiber during polymerization.

  9. Liquid and Gas Permeation Studies on the Structure and Properties of Polyamide Thin-Film Composite Membranes

    KAUST Repository

    Duan, Jintang

    2014-11-01

    This research was undertaken to improve the understanding of structure-property-performance relationships in crosslinked polyamide (PA) thin-film composite (TFC) membranes as characterized by liquid and gas permeation studies. The ultrathin PA selective layer formed by interfacial polymerization between meta-phenylene diamine and trimesoyl chloride was confirmed to contain dense polymer matrix regions and defective regions in both dry and hydrated states. The first part of this research studied the effect of non-selective convection through defective regions on water flux and solute flux in pressure-assisted forward osmosis (PAFO). Through systematic comparison with cellulose triacetate (CTA) and PEBAX-coated PA-TFC membranes, the existence of defects in pristine, hydrated PA-TFC membranes was verified, and their effects were quantified by experimental and modeling methods. In the membrane orientation of selective layer facing the draw solution, water flux increases of up to 10-fold were observed to result from application of low hydraulic pressure (1.25 bar). Convective water flux through the defects was low (< 1% of total water flux for PA-TFC membranes) and of little consequence in practical FO or reverse osmosis (RO) applications. However, it effectively mitigated the concentration polarization in PAFO and therefore greatly increased the diffusive flux through the dense regions. The second part of this research characterized the structures of the PA material and the PA selective layer by gas adsorption and gas permeation measurements. Gas adsorption isotherms (N2 at 77K, CO2 at 273K) confirmed the microporous nature of PA in comparison with dense CTA and polysulfone materials. Gas permeation through the commercial PA-TFC membranes tested occurred primarily in the defective regions, resulting in Knudsen gas selectivity for various gas pairs. Applying a Nafion coating layer effectively plugged the defects and allowed gas permeation through the dense PA regions

  10. Wine Chemical Composition and Radical Scavenging Activity of Some Cabernet Franc Clones.

    Science.gov (United States)

    Popovic-Djordjevic, Jelena; Pejin, Boris; Dramicanin, Aleksandra; Jovic, Sonja; Vujovic, Dragan; Zunic, Dragoljub; Ristic, Renata

    2017-01-01

    Three clones of Cabernet Franc (Nos. 02, 010 and 012) were selected in the last phase of clonal selection in Serbia. Wines made from each clone were assessed for quality parameters and taste during five consecutive vintages (2008-2012) and compared to the standard. The wine quality was determined based on the following parameters: alcohol, total extract, anthocyanins, tannins, pH, titratable acidity, volatile acidity, aldehydes, esters and reducing sugars, relative density, ash, colour, tonality, and tasting score. In the last year of the study, grapes and wines of Cabernet Franc clones and a standard were subjected to a chemical analysis of their phenolic composition, resveratrol and radical scavenging activity. In the last year of the study, grapes and wines of Cabernet Franc clones and a standard were subjected to a chemical analysis of their phenolic composition, resveratrol and radical scavenging activity. Chemical analyses of grapes and wines along with sensory and radical scavenging activity evaluations were done according to the standard procedures. The wines of the clone No. 010 showed some superior properties compared to the other two clones and the standard; in five-year period the average concentration of anthocyanins (179±3.8 mg/L) and polyphenolics (1.85±0.02 g/L) was significantly higher than in wines of clones and the standard, (168-173 mg/L and 1.63-1.74 g/L for anthocyanins and phenolics, respectively). Furthermore, the same clone had a higher alcohol content (13.97±0.03%) in each year of the study, which indicated that it ripened faster than other clones (13.06-13.08 %) and compared to the standard (13.04±0.07%). This finding suggested that the clone No. 010 could possibly have a significant economic impact and further increase popularity of Cabernet Franc in a cooler climate viticultural region. It was also found to have the highest contents of aldehydes (488±1.54 mg/L) and esters (322±0.71 mg/L) compared to aldehydes (452-467 mg/L) and

  11. Total phenolic content, radical scavenging properties, and essential oil composition of Origanum species from different populations.

    Science.gov (United States)

    Dambolena, José S; Zunino, María P; Lucini, Enrique I; Olmedo, Rubén; Banchio, Erika; Bima, Paula J; Zygadlo, Julio A

    2010-01-27

    The aim of this work was to compare the antiradical activity, total phenol content (TPC), and essential oil composition of Origanum vulgare spp. virens, Origanum x applii, Origanum x majoricum, and O. vulgare spp. vulgare cultivated in Argentina in different localities. The experiment was conducted in the research station of La Consulta (INTA-Mendoza), the research station of Santa Lucia (INTA-San Juan), and Agronomy Faculty of National University of La Pampa, from 2007 to 2008. The composition of the essential oils of oregano populations was independent of cultivation conditions. In total, 39 compounds were identified in essential oils of oregano from Argentina by means of GC-MS. Thymol and trans-sabinene hydrate were the most prominent compounds, followed by gamma-terpinene, terpinen-4-ol, and alpha-terpinene. O. vulgare vulgare is the only Origanum studied which is rich in gamma-terpinene. Among tested oregano, O. x majoricum showed the highest essential oil content, 3.9 mg g(-1) dry matter. The plant extract of O. x majoricum had greater total phenol content values, 19.36 mg/g dry weight, than the rest of oregano studied. To find relationships among TPC, free radical scavenging activity (FRSA), and climate variables, canonical correlations were calculated. The results obtained allow us to conclude that 70% of the TPC and FRSA variability can be explained by the climate variables (R(2) = 0.70; p = 8.3 x 10(-6)), the temperature being the most important climatic variable.

  12. Utilization of rice husk ash as filler for polyamide 6 and ionizing radiation effect studies on this composite;Utilizacao da cinza da casca de arroz como carga em matriz de poliamida 6 submetida a radiacao ionizante

    Energy Technology Data Exchange (ETDEWEB)

    Ferro, Waldir Pedro

    2009-07-01

    In order to improve the dimensional stability, as well as, electrical, mechanical and thermal properties of polymers, new filler to this purpose has been developed. The mos applied filler to propitiate the features previously mentioned are the glass and carbon fibers, the mineral filler as the calcium carbonate, the talc and the micro glass sphere. The main aim of this work was to study the rice husk ash as filler for polyamide 6 and ionizing radiation effect studies on this composite, irradiated by electron beam at different doses, since it is constituted of at least 90% of silicon dioxide, and compared with the talc which is the most applied mineral filler. This comparison was made from a compound made through the refined rice husk ash and the polyamide 6 (PA 6), which is one of the main engineering plastic with applications in several productive areas. The samples were injected and irradiated in a electron accelerator. Afterwards, their mechanical and thermal properties were measured. It was also inject automotive parts to verify the processing of the PA 6 with CCA. The results showed that the use of the rice husk ash as filler for polyamide 6 composite is technically and economically viable. The irradiation of the studied composite (PA 6 with 30% of rice husk ash) did not provide any improvement for the mechanical and thermal properties previously appraised. (author)

  13. Identification, characterisation and composition of scavengeable feed resources for rural poultry production in Central Tanzania

    NARCIS (Netherlands)

    Goromela, E.H.; Kwakkel, R.P.; Verstegen, M.W.A.; Katule, A.M.

    2007-01-01

    A participatory study was carried out in four villages of central Tanzania to appraise existing and potential scavengeable feed resources available for rural poultry. In addition, proximate analysis of selected scavengeable feed resources including chicken crop and gizzards contents was carried out

  14. A novel reduced graphene oxide decorated with halloysite nanotubes (HNTs-d-rGO hybrid composite and its flame-retardant application for polyamide 6

    Directory of Open Access Journals (Sweden)

    M. F. Zhu

    2014-06-01

    Full Text Available The improvement of flame-retardant properties of polyamide 6 (PA6 was achieved by using reduced graphene oxide decorated with halloysite nanotubes (HNTs-d-rGO hybrid composite as the additive in PA6 matrix. The intimate integration of reduced graphene oxide (rGO and halloysite nanotubes (HNTs through a three-step chemical functionalization, enabled the combination of their unique physical and chemical characteristics together. The nanostructure of HNTs-d-rGO was determined by Fourier transform infrared spectroscopy (FTIR, X-ray photoelectron spectroscopy (XPS and transmission electron microscopy (TEM. A morphological study revealed that HNTs-d-rGO was dispersed uniformly in PA6 matrix. From the results of cone calorimetry measurements, the fire retardant properties of PA6 were further improved with the addition of HNTs-d-rGO when compared with that of either HNTs, or GO, or a mixture of HNTs and GO (HNTs-m-GO used in PA6 matrix. The results indicate clearly that higher flame-retardant activity of the integrated HNTs-d-rGO nanostructures than that of the simple mixture verifies the importance of the intimate integration between HNTs and rGO, which ascribe to the combination of the stable silica layer created by HNT and the barrier effect of rGO.

  15. Effect of CO{sub 2}-laser irradiation on properties and performance of thin-film composite polyamide reverse osmosis membrane

    Energy Technology Data Exchange (ETDEWEB)

    Jahangiri, Foad; Mousavi, Seyyed Abbas; Farhadi, Fathollah; Sabzi, Behnam; Chenari, Zeinab [Sharif University of Technology, Tehran (Iran, Islamic Republic of); Vatanpour, Vahid [Kharazmi (Tarbiat Moallem) University, Tehran (Iran, Islamic Republic of)

    2016-03-15

    CO{sub 2}-laser irradiation was used to modify the surface properties of thin-film composite (TFC) polyamide reverse osmosis (RO) membranes. These membranes were first synthesized via interfacial polymerization of m-phenylenediamine (MPD) monomers and trimesoyl chloride (TMC) over porous polysulfone ultrafiltration support, followed by a CO{sub 2}-irradiation. AFM, ATR-FTIR, SEM and contact angle measurements were used to characterize the surface properties of these membranes. The ATR-FTIR results indicated that CO{sub 2}-laser irradiation did not induce any functional groups on the membrane surface. However, it was found that the laser irradiation enhanced the NaCl salt rejection and slightly reduced the permeate flux. Moreover, the maintenance of the flux in modified membranes was much higher than untreated ones. Specially, after 180 min of filtration, the reduction in initial flux for the unmodified membranes was 22%. However, the reduction in initial flux for the modified membranes was less than 5%. Bovine serum albumin (BSA) filtration revealed an improvement in the antifouling properties of the modified membranes. The changes in the membrane surface morphology showed that the roughness of membrane surface is reduced significantly.

  16. Radical Scavenging Capacity of Methanolic Phillyrea latifolia L. Extract: Anthocyanin and Phenolic Acids Composition of Fruits

    Directory of Open Access Journals (Sweden)

    Naciye Erkan

    2013-01-01

    Full Text Available Radical scavenging capacity of a crude methanolic extract from the fruits of Phillyrea latifolia L., commonly known as green olive tree or mock privet, was investigated with reference to anthocyanin standards, as flavonoids, and phenolic acid standards, as phenylpropanoids. Characterization with high performance liquid chromatography-diode array detection (HPLC-DAD indicated the presence of keracyanin, kuromanin, cyanidin, ferulic acid, caffeic acid and rosmarinic acid at amounts of 289.1, 90.4, 191.4, 225.2, 221.2 and 190.1 mg/100 g fresh weight (FW of fruits, respectively. Chlorogenic and p-coumaric acids were found to exist in lower amounts. Trolox equivalent antioxidant capacity (TEAC and IC50 values of the plant extract were found to be 1.8 mM Trolox equivalents (TE/g FW of fruits and 69.4 µg/mL, respectively, indicating the close radical scavenging activity of the extract to those of keracyanin and p-coumaric acid. The crude methanolic P. latifolia L. fruit extract was seen to be fairly potent in radical scavenging. Total phenolic content (TPC of the plant extract was found to be 1652.9 mg gallic acid equivalent (GAE/100 g FW of fruits.

  17. Taguchi analysis of extrusion variables and composition effects on the morphology and mechanical properties of EPR-g-MA toughened polyamide 6 and its composite with short glass fiber

    International Nuclear Information System (INIS)

    Shojaei, A.; Fereydoon, M.

    2009-01-01

    Various compositions of maleated ethylene-propylene-rubber (EPR-g-MA) toughened polyamide 6 without and with short glass fiber, i.e. 5-20 wt.% rubber and 5-20 wt.% fiber, are prepared using an industrial twin-screw extruder at different levels of feed rate (100-250 kg/h), screw speed (200-450 rpm) and barrel temperature (230-260 deg. C). Trial runs designed based on the Taguchi's orthogonal arrays are subjected to tensile, impact, scanning electron microscopy (SEM) and optical microscopy tests; and the results are used to perform the analysis of variance (ANOVA). It is shown that the rubber particle size decreases significantly by increasing the rubber content for the unreinforced blend. The results also indicate that the composition of the compounds is the most influential factor on the phase morphology and mechanical properties of both the unreinforced and reinforced blends compared to the extrusion variables. But the processing parameters can also influence the performance characteristics slightly. The most important processing parameter, among the others, is shown to be the mixing temperature, which decreases the fiber length greatly and leads to the thermo-mechanical degradation of the polymers above 240 deg. C

  18. Effect of processing on phenolic acids composition and radical scavenging capacity of barley pasta.

    Science.gov (United States)

    De Paula, Rosanna; Rabalski, Iwona; Messia, Maria Cristina; Abdel-Aal, El-Sayed M; Marconi, Emanuele

    2017-12-01

    Phenolic acids, total phenolics content and DPPH radical scavenging capacity in raw ingredients, fresh and dried spaghetti, and in uncooked and cooked spaghetti were evaluated and compared with semolina spaghetti as a reference. Ferulic acid was the major phenolic acid found in the free and bound phenolic extracts in all the investigated pasta samples. The addition of barley flour into pasta at incorporation levels of 30, 50 and 100% increased phenolic acids and total phenolics content. Pasta processing did not significantly affect the total phenolics content and free radical scavenging capacity, but a significant reduction in total phenolic acids measured by HPLC was found. Drying process differently affected individual phenolic compounds in the free and bound fractions, and thus, the total phenolic acids content. Free vanillic, caffeic and p-coumaric acids did not significantly change, while p-hydroxybenzoic and ferulic acids of the free extracts showed higher values compared to the corresponding fresh pasta. Cooking did not greatly affect total phenolic acids, more leading to conserving free and bound phenolic compounds. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Phytochemical composition and radical scavenging activities of watermelon (Citrullus lanatus seed constituents

    Directory of Open Access Journals (Sweden)

    O. L. Otutu

    2016-01-01

    Full Text Available It is a known fact that antioxidant phytochemicals in foods have many health benefits including prevention of various diseases associated with oxidative stress such as cancer, cardiovascular disease, neuro-degeneration and diabetes. Watermelon seed constituents (whole meal, shelled and shells flours were evaluated for phytochemical components and in vitro antioxidant activity to determine the potential practical applications in food and other related areas. Antioxidant activity was investigated by measuring its DPPH (2,2-diphenyl-2-picryl hydrazyl and ABTS (2, 2’-azinobis-3-ethylbenzothiozoline- 6-sulphonic acid radical scavenging ability as well as FRAP method (ferric reducing power. Quantitative estimation of the constituents showed cardiac glycosides (9.94-14.35 mg/g and saponins (11.62-32.48 mg/g as the most concentrated phytochemicals in the constituents, while alkaloids (47.2-95.8 mg/g, total phenol (5.63-8.40 mg GAE/g, flavonoids 3.51-7.76 mg QE/g. A positive radical scavenging ability of the constituents against ABTS and DPPH free radicals ranged from 0.02 to 0.04 mg Trolox equivalent /g seed flour and 39.89 to 61.11 mg ascorbic acid equivalent /g seed flour respectively. There was a considerable ferric reducing power and higher activity was observed in whole meal than shelled seeds and shells. The significant antioxidant capacities of the seed constituents underline the potential source of natural antioxidants and bioactive compounds for therapeutic purposes.

  20. Amide Link Scission in the Polyamide Active Layers of Thin-Film Composite Membranes upon Exposure to Free Chlorine: Kinetics and Mechanisms.

    Science.gov (United States)

    Powell, Joshua; Luh, Jeanne; Coronell, Orlando

    2015-10-20

    The volume-averaged amide link scission in the aromatic polyamide active layer of a reverse osmosis membrane upon exposure to free chlorine was quantified at a variety of free chlorine exposure times, concentrations, and pH and rinsing conditions. The results showed that (i) hydroxyl ions are needed for scission to occur, (ii) hydroxide-induced amide link scission is a strong function of exposure to hypochlorous acid, (iii) the ratio between amide links broken and chlorine atoms taken up increased with the chlorination pH and reached a maximum of ∼25%, (iv) polyamide disintegration occurs when high free chlorine concentrations, alkaline conditions, and high exposure times are combined, (v) amide link scission promotes further chlorine uptake, and (vi) scission at the membrane surface is unrepresentative of volume-averaged scission in the active layer. Our observations are consistent with previously proposed mechanisms describing amide link scission as a result of the hydrolysis of the N-chlorinated amidic N-C bond due to nucleophilic attack by hydroxyl ions. This study increases the understanding of the physicochemical changes that could occur for membranes in treatment plants using chlorine as an upstream disinfectant and the extent and rate at which those changes would occur.

  1. Bulk chlorine uptake by polyamide active layers of thin-film composite membranes upon exposure to free chlorine-kinetics, mechanisms, and modeling.

    Science.gov (United States)

    Powell, Joshua; Luh, Jeanne; Coronell, Orlando

    2014-01-01

    We studied the volume-averaged chlorine (Cl) uptake into the bulk region of the aromatic polyamide active layer of a reverse osmosis membrane upon exposure to free chlorine. Volume-averaged measurements were obtained using Rutherford backscattering spectrometry with samples prepared at a range of free chlorine concentrations, exposure times, and mixing, rinsing, and pH conditions. Our volume-averaged measurements complement previous studies that have quantified Cl uptake at the active layer surface (top ≈ 7 nm) and advance the mechanistic understanding of Cl uptake by aromatic polyamide active layers. Our results show that surface Cl uptake is representative of and underestimates volume-averaged Cl uptake under acidic conditions and alkaline conditions, respectively. Our results also support that (i) under acidic conditions, N-chlorination followed by Orton rearrangement is the dominant Cl uptake mechanism with N-chlorination as the rate-limiting step; (ii) under alkaline conditions, N-chlorination and dechlorination of N-chlorinated amide links by hydroxyl ion are the two dominant processes; and (iii) under neutral pH conditions, the rates of N-chlorination and Orton rearrangement are comparable. We propose a kinetic model that satisfactorily describes Cl uptake under acidic and alkaline conditions, with the largest discrepancies between model and experiment occurring under alkaline conditions at relatively high chlorine exposures.

  2. Investigating the property profile of polyamide-alumina nanocomposite materials

    International Nuclear Information System (INIS)

    Sarwar, Muhammad Ilyas; Zulfiqar, Sonia; Ahmad, Zahoor

    2009-01-01

    Transparent sol-gel-derived nanocomposites were prepared by incorporating an alumina network into a polyamide matrix. Different amounts of aluminum butoxide were hydrolyzed and condensed to produce the alumina network. Thin composite films were characterized in terms of their optical, morphological, mechanical and thermomechanical properties. Tensile modulus, stress at both yield and break points, improved for alumina loadings of 5-10 wt.%. The glass transition temperature increased to 140 o C for nanocomposites containing 15 wt.% alumina. Scanning electron microscopy investigations indicated a uniform distribution of alumina in the polyamide matrix.

  3. The influence of particle composition on Thorium scavenging in the Mediterranean Sea

    International Nuclear Information System (INIS)

    Roy-Barman, M.; Lemaitre, C.; Ayrault, S.; Lemaitre, C.; Jeandel, C.; Souhaut, M.

    2009-01-01

    Sediment trap data are crucial for the study of marine biochemical cycles but they need careful validation by Thorium (Th) isotopes. In the present study, 230 Th, 232 Th, Uranium (U), Aluminum (Al), Barium (Ba) and Manganese (Mn) were analyzed in sinking particles collected by moored sediment traps in the Ligurian sea (DYFAMED site) in order to determine the collection efficiency of the traps and to constrain which particulate phase(s) carries Th isotopes in a region with strong lithogenic inputs. The 230 Th xs evaluation was based on the U content of each sample rather than on the 232 Th content of each sample and the average 238 U/ 232 Th ratio of the continental crust because the latter method introduced too much uncertainty in the calculation. High trapping efficiencies (187 ± 85% at 200 m and 87 ± 11% at 1000 m) indicated no evidence of particle under-collection by the traps. The lack of correlation between 230 Th xs and the carbonate or the organic matter fraction suggests that these phases are not major 230 Th xs -carrying phases in the deep ocean. For most samples of the time series, the 230 Th xs concentration is correlated with the lithogenic fraction and the Mn concentration, but pulses of particles with high lithogenic and Mn content and low 230 Th xs concentration occur in winter. Assuming that 230 Th xs is only carried by lithogenic particles, we estimate K d Th litho ranges from (0.42 ± 0.04) * 10 7 ml/g to (0.8 ± 0.2) * 10 7 ml/g. Assuming that 230 Th xs is only carried by authigenic Mn oxide precipitates (MnO 2 ), we estimate that K d Th MnO2 ) ranges from (0.6 ± 0.1) * 10 10 ml/g to (1.1 ± 0.4) * 10 10 ml/g. The relative variation of K d T h MnO2 ) (a factor 7) between different oceanic sites is significantly lower than the relative variation of K d Th litho (a factor 50), suggesting that 230 Th xs has a tighter link with MnO 2 rather than with lithogenic particles and hence that 230 Th xs may be more likely scavenged by MnO 2 than by

  4. Stabilization of modified polyamide matrix

    International Nuclear Information System (INIS)

    Marchini, Leonardo G.; Parra, Duclerc F.; Lugao, Ademar B.

    2011-01-01

    Films of PA 6 (polyamide) doped with europium luminescent complexes have been develop and studied for applications in advanced technologies. Development of optical marker for process monitoring is the focus of the present study. Based in doped luminescent polyamide samples were prepared for polymer processing use. Films were prepared by dissolution of PA 6 in acid moiety with addition of europium complex. Stability evaluation was done in samples submitted to irradiation with 10 and 100 kGy of ionizing source. The luminescent polymer matrices were characterized using the techniques of infrared, thermogravimetry, differential scanning calorimetry and photoluminescent properties by electron emission spectroscopy. (author)

  5. Stabilization of modified polyamide matrix

    Energy Technology Data Exchange (ETDEWEB)

    Marchini, Leonardo G.; Parra, Duclerc F.; Lugao, Ademar B., E-mail: dfparra@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    Films of PA 6 (polyamide) doped with europium luminescent complexes have been develop and studied for applications in advanced technologies. Development of optical marker for process monitoring is the focus of the present study. Based in doped luminescent polyamide samples were prepared for polymer processing use. Films were prepared by dissolution of PA 6 in acid moiety with addition of europium complex. Stability evaluation was done in samples submitted to irradiation with 10 and 100 kGy of ionizing source. The luminescent polymer matrices were characterized using the techniques of infrared, thermogravimetry, differential scanning calorimetry and photoluminescent properties by electron emission spectroscopy. (author)

  6. Assessing the fatty acid, essential oil composition, their radical scavenging and antibacterial activities of Schinus terebinthifolius Raddi leaves and twigs.

    Science.gov (United States)

    Ennigrou, Asma; Casabianca, Hervé; Vulliet, Emmanuelle; Hanchi, Belgacem; Hosni, Karim

    2018-04-01

    The fatty acid, essential oil compositions and their respective antioxidant and antibacterial activities was determined in Schinus terebinthifolius Raddi leaves and twigs. The lipid content ranged from 1.75 to 4.65% in twigs and leaves, respectively. Thirteen fatty acids were identified with α-linolenic (C18:3), palmitic (C16:0) and linoleic (C18:2) acids being the main components. The essential oils of both organs were characterized by a high amount of monoterpene hydrocarbons (68.91-74.88%) with α-phellandrene (33.06-36.18%), α-pinene (14.85-15.18%) and limonene (6.62-8.79%) being the chief components. The DPPH˙ radical scavenging assay revealed that both oils have a very weak antiradical activity. In contrast, they showed an appreciable antibacterial activity against the gram-positive Enterococcus feacium (ATCC 19434) and Streptococcus agalactiae (ATCC 13813) bacteria. These results suggest that leaves and twigs of S. terebinthifolius could be considered as an important dietary source of health promoting phytochemicals and has a good potential for use in food industry and pharmacy.

  7. Integrated effect of supramolecular self-assembled sandwich-like melamine cyanurate/MoS{sub 2} hybrid sheets on reducing fire hazards of polyamide 6 composites

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Xiaming [State Key Laboratory of Fire Science, University of Science and Technology of China, Anhui 230026 (China); Suzhou Key Laboratory of Urban Public Safety, Suzhou Institute for Advanced Study, University of Science and Technology of China, Suzhou, Jiangsu 215123 (China); Wang, Xin, E-mail: wxcmx@ustc.edu.cn [State Key Laboratory of Fire Science, University of Science and Technology of China, Anhui 230026 (China); Cai, Wei; Hong, Ningning [State Key Laboratory of Fire Science, University of Science and Technology of China, Anhui 230026 (China); Hu, Yuan, E-mail: yuanhu@ustc.edu.cn [State Key Laboratory of Fire Science, University of Science and Technology of China, Anhui 230026 (China); Suzhou Key Laboratory of Urban Public Safety, Suzhou Institute for Advanced Study, University of Science and Technology of China, Suzhou, Jiangsu 215123 (China); Liew, Kim Meow [Suzhou Key Laboratory of Urban Public Safety, Suzhou Institute for Advanced Study, University of Science and Technology of China, Suzhou, Jiangsu 215123 (China); Department of Architectural and Civil Engineering, City University of Hong Kong, Tat Chee Avenue, Kowloon (Hong Kong)

    2016-12-15

    A novel strategy of using supramolecular self-assembly for preparing sandwich-like melamine cyanurate/MoS{sub 2} sheets as the hybrid flame retardants for polyamide 6 (PA6) is reported for the first time. The introduction of MoS{sub 2} sheets function not only as a template to induce the formation of two-dimensional melamine cyanurate capping layers but also as a synergist to generate integrated flame-retarding effect of hybrid sheets, as well as a high-performance smoke suppressor to reduce fire hazards of PA6 materials. Once incorporating this well-designed structures (4 wt%) into PA6 matrix, there resulted in a remarkable drop (40%) in the peak heat release rate and a 25% reduction in total heat release. Moreover, the smoke production and pyrolysis gaseous products were efficiently suppressed by the addition of sandwich-like hybrid sheets. The integrated functions consisting of inherent flame retarding effect, physical barrier performance and catalytic activity are believed to the crucial guarantee for the reduced fire hazards of PA6 nanocomposites. Furthermore, this novel strategy with facile and scalable features may provide reference for developing various kinds of MoS{sub 2} based hybrid sheets for diverse applications.

  8. Electronic properties of polyamide-PPy/metal junction and electrical conductivity of a typical sample at low temperatures

    International Nuclear Information System (INIS)

    Suenel, N.; Sedef, A.G.; Parlak, M.; Toppare, L.

    2005-01-01

    Electronic properties of junctions fabricated by polyamide-polypyrrole composite films polymerized with adjusted doping concentration and various metal contacts (In, Al, Au and Ag) were investigated. For the junctions giving good rectification I 0 , n and φ b were specified. Conductivity of polyamide-polypyrrole composite polymer was obtained as a function of temperature in the 70-320 K range and was found to obey the VRH model. In addition the Mott parameters were evaluated

  9. Electronic properties of polyamide-PPy/metal junction and electrical conductivity of a typical sample at low temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Suenel, N. [Gaziosmanpasa University, Physics Department, Tasliciftlik Kampasu, Tokat (Turkey)]. E-mail: nsunel@gop.edu.tr; Sedef, A.G. [Gaziosmanpasa University, Physics Department, Tasliciftlik Kampasu, Tokat (Turkey); Parlak, M. [Middle East Technical University, Physics Department, Ankara (Turkey); Toppare, L. [Middle East Technical University, Chemistry Department, Ankara (Turkey)

    2005-05-15

    Electronic properties of junctions fabricated by polyamide-polypyrrole composite films polymerized with adjusted doping concentration and various metal contacts (In, Al, Au and Ag) were investigated. For the junctions giving good rectification I{sub 0}, n and {phi}{sub b} were specified. Conductivity of polyamide-polypyrrole composite polymer was obtained as a function of temperature in the 70-320 K range and was found to obey the VRH model. In addition the Mott parameters were evaluated.

  10. Ultrathin Polyamide Membranes Fabricated from Free-Standing Interfacial Polymerization: Synthesis, Modifications, and Post-treatment

    KAUST Repository

    Cui, Yue

    2016-12-21

    The thin film composite (TFC) membrane synthesized via interfacial polymerization is the workhorse of the prevalent membrane technologies such as nanofiltration (NF), reverse osmosis (RO), forward osmosis (FO), and pressure retarded osmosis (PRO) membranes. The polyamide selective layer usually possesses a high selectivity and permeability, making it the heart of this membrane technology. To further improve and understand its formation, with entirely excluding the effect of substrate, an ultrathin membrane which consists of only the polyamide selective layer has been fabricated via free-standing interfacial polymerization between M-phenylenediamine (MPD) and trimesoyl chloride (TMC) in this study. The influences of monomer concentration on polyamide layer formation is first examined. Different from previous studies which indicated that the variation of MPD concentration might affect the polyamide layer formation even when in excess, the MPD concentration when in excess does not affect membrane properties significantly, while increasing the TMC concentration gradually densifies the polyamide layer and enhances its transport resistance. Adding lithium bromide (LiBr) and sodium dodecyl sulfate (SDS) in MPD solutions is found to facilitate the reaction between the two phases and result in a significant improvement in water permeability. However, a high amount of additives leads to an augmentation in transport resistance. The N,N-dimethylformamide (DMF) treatment on the polyamide membrane shows pronounced improvements on water flux under FO tests and water permeability under RO tests without compromising reverse salt flux and salt rejection because the dense polyamide core stays intact. This study may offer a different perspective on membrane formation and intrinsic properties of the polyamide selective layer and provide useful insights for the development of next-generation TFC membranes.

  11. Effect of Multiwalled Carbon Nanotubes on the Mechanical Properties of Carbon Fiber-Reinforced Polyamide-6/Polypropylene Composites for Lightweight Automotive Parts

    Directory of Open Access Journals (Sweden)

    Huu-Duc Nguyen-Tran

    2018-03-01

    Full Text Available The development of lightweight automotive parts is an important issue for improving the efficiency of vehicles. Polymer composites have been widely applied to reduce weight and improve mechanical properties by mixing polymers with carbon fibers, glass fibers, and carbon nanotubes. Polypropylene (PP has been added to carbon fiber-reinforced nylon-6 (CF/PA6 composite to achieve further weight reduction and water resistance. However, the mechanical properties were reduced by the addition of PP. In this research, multiwalled carbon nanotubes (CNTs were added to compensate for the reduced mechanical properties experienced when adding PP. Tensile testing and bending tests were carried out to evaluate the mechanical properties. A small amount of CNTs improved the mechanical properties of carbon fiber-reinforced PA6/PP composites. For example, the density of CF/PA6 was reduced from 1.214 to 1.131 g/cm3 (6.8% by adding 30 wt % PP, and the tensile strength of 30 wt % PP composite was improved from 168 to 173 MPa (3.0% by adding 0.5 wt % CNTs with small increase of density (1.135 g/cm3. The developed composite will be widely used for lightweight automotive parts with improved mechanical properties.

  12. Chemical composition, botanical evaluation and screening of radical scavenging activity of collected pollen by the stingless bees Melipona rufiventris (Uruçu-amarela).

    Science.gov (United States)

    Silva, Tania M S; Camara, Celso A; Lins, Antonio C S; Agra, Maria de Fátima; Silva, Eva M S; Reis, Igor T; Freitas, Breno M

    2009-06-01

    Stingless bees in Brazil are indigenous and found all over the country. Bee pollen is used for its nutritional value in the human diet. It is made up of natural flower pollen mixed with nectar and bee secretions. In order to evaluate the chemical composition, free radical scavenging activity, and botanical origin, sample of pollen loads from stingless bee, Melipona rufiventris (Uruçu amarela) was studied. The EtOAc extract of pollen of Melipona rufiventris yielded the following compounds: p-hydroxycinnamic acid, dihydroquercetin, isorhamnetin, isorhamnetin3-O-(6'-O-E-p-coumaroyl)-beta-D-glucopyranoside, luteolin, and quercetin. This is the first report of the isolation of isorhamnetin3-O-(6'O-E-p-coumaroyl)beta-D-glucopyranoside from pollen. The free radicalscavenging activities of different solvent extracts of pollen were determined using DPPH assay. This activity decreases in the order: EtOAc>EtOH>Hexane extract. It appears that the EtOAc extract of the pollen is a good scavenger of active oxygen species. The botanical evaluation of pollen loads showed the composition by two pollen types, with the dominant type (97.3%) being Scopariadulcis (L.) (Scrophulariaceae) and the minor one Senna obtusifolia (L.) Irwin & Barneby (Fabaceae). This suggests a specific foraging behavior in Melipona rufiventris bees, even in an environment with such a rich botanical diversity as the Northeastern Brazil.

  13. Experimental comparison of manufacturing techniques of toughened and nanoreinforced polyamides

    Science.gov (United States)

    Siengchin, S.; Bergmann, C.; Dangtungee, R.

    2011-11-01

    Composites consisting of polyamide-6 (PA-6), nitrile rubber (NBR), and sodium fluorohectorite (FH) or alumina silicate (Sungloss; SG) were produced by different techniques with latex precompounding. Their tensile and thermomechanical properties were determined by using tensile tests and a dynamic-mechanical analysis, performed at various temperatures. The PA-6/NBR composite systems produced by the direct melt compounding outperformed those obtained by using the masterbatch technique with respect to the strength and ductility, but the latter ones had a higher storage modulus.

  14. Repair of articular cartilage and subchondral defects in rabbit knee joints with a polyvinyl alcohol/nano-hydroxyapatite/polyamide 66 biological composite material.

    Science.gov (United States)

    Guo, Tao; Tian, Xiaobin; Li, Bo; Yang, Tianfu; Li, Yubao

    2017-11-15

    This study sought to prepare a new PVA/n-HA/PA66 composite to investigate the repair of articular cartilage and subchondral defects in rabbit knee joints. A 5 × 5 × 5 mm-sized defect was created in the patellofemoral joints of 72 healthy adult New Zealand rabbits. The rabbits were then randomly divided into three groups (n = 24): PVA/n-HA+PA66 group, polyvinyl alcohol (PVA) group, and control (untreated) group. Cylindrical PVA/n-HA+PA66, 5 × 5 mm, comprised an upper PVA layer and a lower n-HA+PA66 layer. Macroscopic and histological evaluations were performed at 4, 8, 12, and 24 weeks, postoperatively. Type II collagen was measured by immunohistochemical staining. The implant/cartilage and bone interfaces were observed by scanning electron microscopy. At 24 weeks postoperatively, the lower PVA/n-HA+PA66 layer became surrounded by cartilage, with no obvious degeneration. In the PVA group, an enlarged space was observed between the implant and the host tissue that had undergone degeneration. In the control group, the articular cartilage had become calcified. In the PVA/n-HA+PA66 group, positive type II collagen staining was observed between the composite and the surrounding cartilage and on the implant surface. In the PVA group, positive staining was slightly increased between the PVA and the surrounding cartilage, but reduced on the PVA surface. In the control group, reduced staining was observed throughout. Scanning electron microscopy showed increased bone tissue in the lower n-HA+PA66 layer that was in close approximation with the upper PVA layer of the composite. In the PVA group, the bone tissue around the material had receded, and in the control group, the defect was filled with bone tissue, while the superior aspect of the defect was filled with disordered, fibrous tissue. The diphase biological composite material PVA/n-HA+PA66 exhibits good histocompatibility and offers a satisfactory substitute for articular cartilage and subchondral bone.

  15. Chemical Composition, and Antibacterial (against Staphylococcus aureus and Free-Radical-Scavenging Activities of the Essential Oil of Scrophularia amplexicaulis Benth.

    Directory of Open Access Journals (Sweden)

    Ardalan Pasdaran

    2012-07-01

    Full Text Available Chemical composition of the essential oil obtained from the aerial parts of Scrophularia amplexicaulis Benth. was analyzed, for the first time, by the gas chromatography/mass spectrometry (GC-MS and gas chromatography/flame ionization detection (GC-FID. A total yield of 3 mg of essential oil per100 g of plant dry mass was obtained, and 27 compounds were identified, representing 97. 7 % of total oil. The essential oil were characterized by a high content of oxygenated monoterpenes and phenolic derivatives. The main constituents were eugenol (53.8%, eugenol acetate (24.5%, b -caryophyllene (5.7%, caryophyllene oxide (6.4% and aromadendrene oxide II (2.1%. The antimicrobial activity of the essential oil was tested against Staphylococcus aureus using the well diffusion method, and t he free-radical-scavenging activity was assessed by the 2,2-diphenyl-picryl-hydrazyl (DPPH assay.

  16. DPPH scavenging, PRAP activities and essential oil composition of edible Lathyrus ochrus L. (Cyprus Vetch, Luvana) from Cyprus.

    Science.gov (United States)

    Polatoğlu, Kaan; Arsal, Seniha; Demirci, Betül; Başer, Kemal Hüsnü Can

    2015-01-01

    The essential oil of the aerial parts of edible Lathyrus ochrus L. was investigated by simultaneous GC, GC/MS analyses under the same conditions. Trace amount of oil (0.01> mL) obtained by hydro distillation of 200 g fresh plants was trapped in 1 mL n-hexane. Twenty components were detected representing 91.55 ± 0.56 % of the oil. The main components were phytol 49.39 ± 0.44 %, hexadecanoic acid 20.64 ± 0.89 % and pentacosane 4.20 ± 0.09 %. Essential oil solution (1% oil: n-hexane) afforded similar DPPH scavenging activity (9.28 ± 1.30 %) when compared with positive controls α-tocopherol (9.74 ± 0.21 %) and BHT (7.79 ± 0.26 %) at the same concentrations. Antioxidant activity of the oil was determined using a new HPTLC-PRAP assay. The oil afforded two fold higher reducing activity of phosphomolybdenum complex (594.85 ± 5.14 AU) when compared with positive controls α- tocopherol (271.10 ± 2.86 AU) and BHT (210.53 ± 1.81 AU) at the same concentration.

  17. Polyamide copolymers having 2,5-furan dicarboxamide units

    Science.gov (United States)

    Chisholm, Bret Ja; Samanta, Satyabrata

    2017-09-19

    Polyamide copolymers, and methods of making and using polyamide copolymers, having 2,5-furan dicarboxamide units are disclosed herein. Such polymers can be useful for engineering thermoplastics having advantageous physical and/or chemical properties.

  18. DPPH Radical Scavenging and Postprandial Hyperglycemia Inhibition Activities and Flavonoid Composition Analysis of Hawk Tea by UPLC-DAD and UPLC-Q/TOF MSE.

    Science.gov (United States)

    Xiao, Xuan; Xu, Lijia; Hu, Huagang; Yang, Yinjun; Zhang, Xinyao; Peng, Yong; Xiao, Peigen

    2017-10-13

    flavonoids were identified or tentatively identified by comparing their retention times and accurate mass measurements with reference compounds or literature data. The bioactive flavonoid composition and DPPH radical scavenging activities present in different Hawk tea raw materials are quite different due to the different ontogenesis of these raw materials. Further studies on PLT showed that the substances in PLT ME could reduce the level of mouse postprandial blood glucose through inhibiting the activity of α-glucosidase.

  19. DPPH Radical Scavenging and Postprandial Hyperglycemia Inhibition Activities and Flavonoid Composition Analysis of Hawk Tea by UPLC-DAD and UPLC-Q/TOF MSE

    Directory of Open Access Journals (Sweden)

    Xuan Xiao

    2017-10-01

    20 flavonoids were identified or tentatively identified by comparing their retention times and accurate mass measurements with reference compounds or literature data. The bioactive flavonoid composition and DPPH radical scavenging activities present in different Hawk tea raw materials are quite different due to the different ontogenesis of these raw materials. Further studies on PLT showed that the substances in PLT ME could reduce the level of mouse postprandial blood glucose through inhibiting the activity of α-glucosidase.

  20. Cholesterol trafficking and raft-like membrane domain composition mediate scavenger receptor class B type 1-dependent lipid sensing in intestinal epithelial cells.

    Science.gov (United States)

    Morel, Etienne; Ghezzal, Sara; Lucchi, Géraldine; Truntzer, Caroline; Pais de Barros, Jean-Paul; Simon-Plas, Françoise; Demignot, Sylvie; Mineo, Chieko; Shaul, Philip W; Leturque, Armelle; Rousset, Monique; Carrière, Véronique

    2018-02-01

    Scavenger receptor Class B type 1 (SR-B1) is a lipid transporter and sensor. In intestinal epithelial cells, SR-B1-dependent lipid sensing is associated with SR-B1 recruitment in raft-like/ detergent-resistant membrane domains and interaction of its C-terminal transmembrane domain with plasma membrane cholesterol. To clarify the initiating events occurring during lipid sensing by SR-B1, we analyzed cholesterol trafficking and raft-like domain composition in intestinal epithelial cells expressing wild-type SR-B1 or the mutated form SR-B1-Q445A, defective in membrane cholesterol binding and signal initiation. These features of SR-B1 were found to influence both apical cholesterol efflux and intracellular cholesterol trafficking from plasma membrane to lipid droplets, and the lipid composition of raft-like domains. Lipidomic analysis revealed likely participation of d18:0/16:0 sphingomyelin and 16:0/0:0 lysophosphatidylethanolamine in lipid sensing by SR-B1. Proteomic analysis identified proteins, whose abundance changed in raft-like domains during lipid sensing, and these included molecules linked to lipid raft dynamics and signal transduction. These findings provide new insights into the role of SR-B1 in cellular cholesterol homeostasis and suggest molecular links between SR-B1-dependent lipid sensing and cell cholesterol and lipid droplet dynamics. Copyright © 2017 Elsevier B.V. All rights reserved.

  1. Peroxynitrite scavenging by flavonids.

    NARCIS (Netherlands)

    Haenen, G.R.M.M.; Paquay, J.B.G.; Korthouwer, R.E.M.; Bast, A.

    1997-01-01

    The peroxynitrite scavenging activity of a series of structurally related flavonoids was tested. It was found that flavonoids are excellent scavengers of peroxynitrite. Compared to the known peroxynitrite scavenger ebselen, the most active flavonoids proved to be 10 times more effective. Indications

  2. Aluminum hypophosphite microencapsulated to improve its safety and application to flame retardant polyamide 6

    Energy Technology Data Exchange (ETDEWEB)

    Ge, Hua [State Key Laboratory of Fire Science, University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026 (China); Tang, Gang [School of Architecture and Civil Engineering, Anhui University of Technology, 59 Hudong Road, Ma’anshan, Anhui 243002 (China); Hu, Wei-Zhao; Wang, Bi-Bo; Pan, Ying [State Key Laboratory of Fire Science, University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026 (China); Song, Lei, E-mail: leisong@ustc.edu.cn [State Key Laboratory of Fire Science, University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026 (China); Hu, Yuan, E-mail: yuanhu@ustc.edu.cn [State Key Laboratory of Fire Science, University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026 (China); Suzhou Key Laboratory of Urban Public Safety, Suzhou Institute for Advanced Study, University of Science and Technology of China, 166 Ren’ai Road, Suzhou, Jiangsu 215123 (China)

    2015-08-30

    Highlights: • MCAHP was prepared and applied in polyamide 6. • MCA as the capsule material can improve the fire safety of AHP. • Flame retardant polyamide 6 composites with MCAHP show good flame retardancy. - Abstract: Aluminum hypophosphite (AHP) is an effective phosphorus-containing flame retardant. But AHP also has fire risk that it will decompose and release phosphine which is spontaneously flammable in air and even can form explosive mixtures with air in extreme cases. In this paper, AHP has been microencapsulated by melamine cyanurate (MCA) to prepare microencapsulated aluminum hypophosphite (MCAHP) with the aim of enhancing the fire safety in the procedure of production, storage and use. Meanwhile, MCA was a nitrogen-containing flame retardant that can work with AHP via the nitrogen-phosphorus synergistic effect to show improved flame-retardant property than other capsule materials. After microencapsulation, MCA presented as a protection layer inhibit the degradation of AHP and postpone the generation of phosphine. Furthermore, the phosphine concentration could be effectively diluted by inert decomposition products of MCA. These nonflammable decomposition products of MCA could separate phosphine from air delay the oxidizing reaction with oxygen and decrease the heat release rate, which imply that the fire safety of AHP has been improved. Furthermore, MCAHP was added into polyamide 6 to prepare flame retardant polyamide 6 composites (FR-PA6) which show good flame retardancy.

  3. Aluminum hypophosphite microencapsulated to improve its safety and application to flame retardant polyamide 6

    International Nuclear Information System (INIS)

    Ge, Hua; Tang, Gang; Hu, Wei-Zhao; Wang, Bi-Bo; Pan, Ying; Song, Lei; Hu, Yuan

    2015-01-01

    Highlights: • MCAHP was prepared and applied in polyamide 6. • MCA as the capsule material can improve the fire safety of AHP. • Flame retardant polyamide 6 composites with MCAHP show good flame retardancy. - Abstract: Aluminum hypophosphite (AHP) is an effective phosphorus-containing flame retardant. But AHP also has fire risk that it will decompose and release phosphine which is spontaneously flammable in air and even can form explosive mixtures with air in extreme cases. In this paper, AHP has been microencapsulated by melamine cyanurate (MCA) to prepare microencapsulated aluminum hypophosphite (MCAHP) with the aim of enhancing the fire safety in the procedure of production, storage and use. Meanwhile, MCA was a nitrogen-containing flame retardant that can work with AHP via the nitrogen-phosphorus synergistic effect to show improved flame-retardant property than other capsule materials. After microencapsulation, MCA presented as a protection layer inhibit the degradation of AHP and postpone the generation of phosphine. Furthermore, the phosphine concentration could be effectively diluted by inert decomposition products of MCA. These nonflammable decomposition products of MCA could separate phosphine from air delay the oxidizing reaction with oxygen and decrease the heat release rate, which imply that the fire safety of AHP has been improved. Furthermore, MCAHP was added into polyamide 6 to prepare flame retardant polyamide 6 composites (FR-PA6) which show good flame retardancy

  4. Effect of graphene oxide on structure and properties of impact-modified polyamide 6

    Czech Academy of Sciences Publication Activity Database

    Kelnar, Ivan; Kratochvíl, Jaroslav; Kaprálková, Ludmila; Špitálsky, Z.; Ujčić, Massimo; Zhigunov, Alexander; Nevoralová, Martina

    2018-01-01

    Roč. 57, č. 9 (2018), s. 827-835 ISSN 0360-2559 R&D Projects: GA ČR(CZ) GA16-03194S Institutional support: RVO:61389013 Keywords : graphene oxide * morphology * polyamide 6 Subject RIV: JI - Composite Materials OBOR OECD: Composites (including laminates, reinforced plastics, cermets, combined natural and synthetic fibre fabrics Impact factor: 1.232, year: 2016

  5. Chemical composition, botanical evaluation and screening of radical scavenging activity of collected pollen by the stingless bees Melipona rufiventris (Uruçu-amarela

    Directory of Open Access Journals (Sweden)

    Tania M.S. Silva

    2009-06-01

    Full Text Available Stingless bees in Brazil are indigenous and found all over the country. Bee pollen is used for its nutritional value in the human diet. It is made up of natural flower pollen mixed with nectar and bee secretions. In order to evaluate the chemical composition, free radical scavenging activity, and botanical origin, sample of pollen loads from stingless bee, Melipona rufiventris (Uruçu amarela was studied. The EtOAc extract of pollen of Melipona rufiventris yielded the following compounds: p-hydroxycinnamic acid, dihydroquercetin, isorhamnetin, isorhamnetin3-O-(6"-O-E-p-coumaroyl-β-D-glucopyranoside, luteolin, and quercetin. This is the first report of the isolation of isorhamnetin3-O-(6"O-E-p-coumaroylβ-D-glucopyranoside from pollen. The free radicalscavenging activities of different solvent extracts of pollen were determined using DPPH assay. This activity decreases in the order: EtOAc>EtOH>Hexane extract. It appears that the EtOAc extract of the pollen is a good scavenger of active oxygen species. The botanical evaluation of pollen loads showed the composition by two pollen types, with the dominant type (97.3% being Scopariadulcis (L. (Scrophulariaceae and the minor one Senna obtusifolia (L. Irwin & Barneby (Fabaceae. This suggests a specific foraging behavior in Melipona rufiventris bees, even in an environment with such a rich botanical diversity as the Northeastern Brazil.As abelhas sem ferrão são espécies indígenas encontradas em todo o Brasil. Seu pólen é utilizado devido ao seu valor nutricional na dieta humana. É produzido a partir de pólen floral misturado com néctar e líquidos secretados pelas abelhas. Visando avaliar a composição química, a atividade sequestradora de radicais livres e a origem botânica foi estudado o pólencoletado pela abelha sem ferrão Melipona rufiventris (Uruçu-amarela. Do extrato acetato de etila foram isolados os compostos: ácido phidroxicinâmico, dihidroquercetina, isoramnetina, 3O(6

  6. Synthesis of Cyclic Py-Im Polyamide Libraries

    OpenAIRE

    Li, Benjamin C.; Montgomery, David C.; Puckett, James W.; Dervan, Peter B.

    2013-01-01

    Cyclic Py-Im polyamides containing two GABA turn units exhibit enhanced DNA binding affinity, but extensive studies of their biological properties have been hindered due to synthetic inaccessibility. A facile modular approach toward cyclic polyamides has been developed via microwave-assisted solid-phase synthesis of hairpin amino acid oligomer intermediates followed by macrocyclization. A focused library of cyclic polyamides 1–7 targeted to the androgen response element (ARE) and the estrogen...

  7. Preparation and Characterization of Silica/Polyamide-imide Nanocomposite Thin Films

    Directory of Open Access Journals (Sweden)

    Hwang Jong-Sun

    2010-01-01

    Full Text Available Abstract The functional silica/polyamide-imide composite films were prepared via simple ultrasonic blending, after the silica nanoparticles were modified by cationic surfactant—cetyltrimethyl ammonium bromide (CTAB. The composite films were characterized by scanning electron microscope (SEM, thermo gravimetric analysis (TGA and thermomechanical analysis (TMA. CTAB-modified silica nanoparticles were well dispersed in the polyamide-imide matrix, and the amount of silica nanoparticles to PAI was investigated to be from 2 to 10 wt%. Especially, the coefficients of thermal expansion (CET continuously decreased with the amount of silica particles increasing. The high thermal stability and low coefficient of thermal expansion showed that the nanocomposite films can be widely used in the enamel wire industry.

  8. Botanical Scavenger Hunt

    Science.gov (United States)

    Walker-Livingston, Wendy

    2009-01-01

    Why not combine the use of technology with the excitement of a scavenger hunt that moves middle-level students out into the "wilds" of their school campus to classify plants? In the lesson plan described here, students embark on a botanical scavenger hunt and then document their findings using a digital camera. This project was designed to allow…

  9. Laser surface treatment of polyamide and NiTi alloy and the effects on mesenchymal stem cell response

    Science.gov (United States)

    Waugh, D. G.; Lawrence, J.; Shukla, P.; Chan, C.; Hussain, I.; Man, H. C.; Smith, G. C.

    2015-07-01

    Mesenchymal stem cells (MSCs) are known to play important roles in development, post-natal growth, repair, and regeneration of mesenchymal tissues. What is more, surface treatments are widely reported to affect the biomimetic nature of materials. This paper will detail, discuss and compare laser surface treatment of polyamide (Polyamide 6,6), using a 60 W CO2 laser, and NiTi alloy, using a 100 W fiber laser, and the effects of these treatments on mesenchymal stem cell response. The surface morphology and composition of the polyamide and NiTi alloy were studied by scanning electron microscopy (SEM) and X-ray photoemission spectroscopy (XPS), respectively. MSC cell morphology cell counting and viability measurements were done by employing a haemocytometer and MTT colorimetric assay. The success of enhanced adhesion and spreading of the MSCs on each of the laser surface treated samples, when compared to as-received samples, is evidenced in this work.

  10. Evaluation of Shear Resisting Capacity of a Prestressed Concrete Containment Building with Steel or Polyamide Fiber Reinforcement

    International Nuclear Information System (INIS)

    Choun, Youngsun; Park, Junhee

    2014-01-01

    Conventional reinforced concrete (RC) members generally show a rapid deterioration in shear resisting mechanisms under a reversed cyclic load. However, the use of high-performance fiber-reinforced cement composites provides excellent damage tolerance under large displacement reversals compared with regular concrete. Previous experimental studies have indicated that the use of fibers in conventional RC can enhance the structural and functional performance of prestressed concrete containment buildings (PCCBs) in nuclear power plants. This study evaluates the shear resisting capacity for a PCCB constructed using steel fiber reinforced concrete (SFRC) or polyamide fiber reinforced concrete (PFRC). The effects of steel and polyamide fibers on the shear performance of a PCCB were investigated. It was revealed that steel fibers are more effective to enhance the shear resisting capacity of a PCCB than polyamide fibers. The ductility and energy dissipation increase significantly in fiber reinforced PCCBs

  11. Evaluation of Shear Resisting Capacity of a Prestressed Concrete Containment Building with Steel or Polyamide Fiber Reinforcement

    Energy Technology Data Exchange (ETDEWEB)

    Choun, Youngsun; Park, Junhee [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    Conventional reinforced concrete (RC) members generally show a rapid deterioration in shear resisting mechanisms under a reversed cyclic load. However, the use of high-performance fiber-reinforced cement composites provides excellent damage tolerance under large displacement reversals compared with regular concrete. Previous experimental studies have indicated that the use of fibers in conventional RC can enhance the structural and functional performance of prestressed concrete containment buildings (PCCBs) in nuclear power plants. This study evaluates the shear resisting capacity for a PCCB constructed using steel fiber reinforced concrete (SFRC) or polyamide fiber reinforced concrete (PFRC). The effects of steel and polyamide fibers on the shear performance of a PCCB were investigated. It was revealed that steel fibers are more effective to enhance the shear resisting capacity of a PCCB than polyamide fibers. The ductility and energy dissipation increase significantly in fiber reinforced PCCBs.

  12. Electron beam induced modification of grafted polyamides

    International Nuclear Information System (INIS)

    Timus, D.M.; Brasoveanu, M.M.; Bradley, D.A.; Popov, A.M.

    1998-01-01

    It is well known that irradiation, when applied on its own or in combination with other physical and chemical treatments, can manifest in radiation damage to materials. Radiation processing technology focuses upon producing favourable modification of materials through use of relatively high dose and dose rates. Current interest is in modifying the thermal and electrical properties of textured polymers in an effort to improve safety and wear comfort of clothing. No less important is the production of textiles which are safe to use, both in homes and offices. Present investigations provide additional data in support of findings which show that polyamides, a particular class of textured polymer, are amenable to radiation processing. Accelerated electron beam irradiation of sheets of polyamide fibre results in induced grafting of acrylic and methacrylic acids. The degree of grafting is critically dependent upon irradiation dose and the extent of monomers dilution. Of particular importance is the high correlation which is found between degree of grafting and a decrease in the softening rate of the modified polyamide. A systematic modification of electrical conductivity is also observed. (author)

  13. Correlating PSf Support Physicochemical Properties with the Formation of Piperazine-Based Polyamide and Evaluating the Resultant Nanofiltration Membrane Performance

    Directory of Open Access Journals (Sweden)

    Micah Belle Marie Yap Ang

    2017-10-01

    Full Text Available Membrane support properties influence the performance of thin-film composite nanofiltration membranes. We fabricated several polysulfone (PSf supports. The physicochemical properties of PSf were altered by adding polyethylene glycol (PEG of varying molecular weights (200–35,000 g/mol. This alteration facilitated the formation of a thin polyamide layer on the PSf surface during the interfacial polymerization reaction involving an aqueous solution of piperazine containing 4-aminobenzoic acid and an organic solution of trimesoyl chloride. Attenuated total reflectance-Fourier transform infrared validated the presence of PEG in the membrane support. Scanning electron microscopy and atomic force microscopy illustrated that the thin-film polyamide layer morphology transformed from a rough to a smooth surface. A cross-flow filtration test indicated that a thin-film composite polyamide membrane comprising a PSf support (TFC-PEG20k with a low surface porosity, small pore size, and suitable hydrophilicity delivered the highest water flux and separation efficiency (J = 81.1 ± 6.4 L·m−2·h−1, RNa2SO4 = 91.1% ± 1.8%, and RNaCl = 35.7% ± 3.1% at 0.60 MPa. This membrane had a molecular weight cutoff of 292 g/mol and also a high rejection for negatively charged dyes. Therefore, a PSf support exhibiting suitable physicochemical properties endowed a thin-film composite polyamide membrane with high performance.

  14. Kinetics of the deformation induced memory effect in polyamide-6

    NARCIS (Netherlands)

    Drongelen, van M.; Stroeks, A.A.M.; Peters, G.W.M.

    2015-01-01

    Nascent polyamide-6 shows a peculiar and irreversible effect; the quiescent crystallization kinetics on cooling are accelerated upon deformation in the melt, even after full relaxation of the melt. This phenomenon, known as the orientation (or better, deformation) induced memory effect of polyamide

  15. 21 CFR 177.2450 - Polyamide-imide resins.

    Science.gov (United States)

    2010-04-01

    ... Components of Articles Intended for Repeated Use § 177.2450 Polyamide-imide resins. Polyamide-imide resins identified in paragraph (a) of this section may be safely used as components of articles intended for... Safety and Applied Nutrition (HFS-200), Food and Drug Administration, 5100 Paint Branch Pkwy., College...

  16. Polyamides : hydrogen bonding, the Brill transition, and superheated water

    NARCIS (Netherlands)

    Dijkstra - Vinken, E.

    2008-01-01

    Aliphatic polyamide, commonly known as nylon, was the world’s first synthetic fiber and has found its largest application range in tires, carpets, stockings, upholstery, and adhesives. All polyamides have a recurring amide group (–CONH–) present in the molecular structure with hydrogen bonds between

  17. The role of supplemental ultraviolet-B radiation in altering the metabolite profile, essential oil content and composition, and free radical scavenging activities of Coleus forskohlii, an indigenous medicinal plant.

    Science.gov (United States)

    Takshak, Swabha; Agrawal, S B

    2016-04-01

    The effects of supplemental ultraviolet-B (s-UV-B; 3.6 kJ m(-2) day(-1) above ambient) radiation were investigated on plant metabolite profile, essential oil content and composition, and free radical scavenging capacities of methanolic extracts of Coleus forskohlii (an indigenous medicinal plant) grown under field conditions. Essential oil was isolated using hydrodistillation technique while alterations in metabolite profile and oil composition were determined via gas chromatography-mass spectroscopy (GC-MS). Leaf and root methanolic extracts were investigated via various in vitro assays for their DPPH radical-, superoxide radical-, hydrogen peroxide-, hydroxyl radical-, and nitric oxide radical scavenging activities, ferrous ion chelating activity, and reducing power. Phytochemical analysis revealed the presence of alkaloids, anthocyanins, coumarins, flavonoids, glycosides, phenols, saponins, steroids, tannins, and terpenoids. Oil content was found to be reduced (by ∼7 %) in supplemental UV-B (s-UV-B) treated plants; the composition of the plant extracts as well as essential oil was also considerably altered. Methanolic extracts from treated plant organs showed more potency as free radical scavengers (their EC50 values being lower than their respective controls). Anomalies were observed in Fe(2+) chelating activity for both leaves and roots. The present study concludes that s-UV-B adversely affects oil content in C. forskohlii and also alters the composition and contents of metabolites in both plant extracts and oil. The results also denote that s-UV-B treated plant organs might be more effective in safeguarding against oxidative stress, though further studies are required to authenticate these findings.

  18. Mixed field radiation effects on dry and acidic solution saturated polyamide 6,6

    Energy Technology Data Exchange (ETDEWEB)

    Brown, L. [Department of Chemistry and Chemical Engineering, Royal Military College of Canada, Kingston, Ont., K7K 7B4 (Canada); Bonin, H.W. [Department of Chemistry and Chemical Engineering, Royal Military College of Canada, Kingston, Ont., K7K 7B4 (Canada)]. E-mail: bonin-h@rmc.ca; Bui, V.T. [Department of Chemistry and Chemical Engineering, Royal Military College of Canada, Kingston, Ont., K7K 7B4 (Canada)

    2005-05-15

    The disposal of Canada's radioactive waste materials has been the focus of ongoing research at the Royal Military College of Canada, in the use of polymer-based composite materials for the fabrication of disposal containers. An evaluation of the performance of polyamide 6,6 after exposure to radiation and acidic aqueous solutions provides the basis for the assessment of the lifetime performance of a polymeric-based storage container. This work demonstrates the importance of the combined effects of aqueous solution diffusion and radiation exposure on the mechanical performance and molecular structure of polyamide 6,6. Irradiation of dry samples initially results in a marked reduction of mechanical performance, however, post-irradiation aging allows for the return to pre-irradiation mechanical strength. Samples irradiated after exposure to either distilled water or 0.1 M sulfuric acid solutions exhibited increases in mechanical performance upon exposure to a mixed field radioactive environment.

  19. Mixed field radiation effects on dry and acidic solution saturated polyamide 6,6

    International Nuclear Information System (INIS)

    Brown, L.; Bonin, H.W.; Bui, V.T.

    2005-01-01

    The disposal of Canada's radioactive waste materials has been the focus of ongoing research at the Royal Military College of Canada, in the use of polymer-based composite materials for the fabrication of disposal containers. An evaluation of the performance of polyamide 6,6 after exposure to radiation and acidic aqueous solutions provides the basis for the assessment of the lifetime performance of a polymeric-based storage container. This work demonstrates the importance of the combined effects of aqueous solution diffusion and radiation exposure on the mechanical performance and molecular structure of polyamide 6,6. Irradiation of dry samples initially results in a marked reduction of mechanical performance, however, post-irradiation aging allows for the return to pre-irradiation mechanical strength. Samples irradiated after exposure to either distilled water or 0.1 M sulfuric acid solutions exhibited increases in mechanical performance upon exposure to a mixed field radioactive environment

  20. Synthesis and Thermal and Photo Behaviors of New Polyamide/Organocaly Nanocomposites Containing Para Phenylenediacrylic Moiety

    Science.gov (United States)

    Faghihi, Khalil; Soleimani, Masoumeh; Shabanian, Meisam; Abootalebi, Ashraf Sadat

    2011-06-01

    New type of aromatic polyamide/montmorillonite nanocomposites were produced using solution process in N-methyl-2-pyrolidone. Amide chains were synthesized from 4,4'-diaminodiphenyl sulfone and p-phenylenediacrylic acid in N-methyl-2-pyrolidone. The resulting nanocomposite films containing 5-15 mass % of organoclay were characterized for FT-IR, scanning electronmicroscopy (SEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), optical transparency and water absorption measurements. The distribution of organoclay and nanostructure of the composites were investigated by (XRD) and SEM analyses. Thermogravimetric analysis indicated an increase in thermal stability of nanocomposites as compared to pristine polyamide. The percentage optical transparency and water absorption of these hybrids was found to be much reduced upon the addition of modified layered silicate indicating decreased permeability.

  1. Evaluation of rheological behavior and structure of nanocomposites with polymer matrices of polyamide 6 and polyethylene

    International Nuclear Information System (INIS)

    Cavalcanti, Shirley N.; Araujo, Edcleide M.; Paz, Rene A.; Gouveia, Taciana R.; Oliveira, Sara V.; Souza, Dayanne D. de

    2009-01-01

    The objective of this study was to evaluate the results of the obtention of nanocomposites from the system of high density polyethylene (PEAD)/polyamide 6/organoclay, using concentrations of (5 and 10wt.%) compatibilizer PE-g-MA, the organoclay was organophilizate with the quaternary ammonium salt Genamin and mixtures were prepared in a twin screw counter rotating extruder, coupled to a Haake torque rheometer. The rheological behavior of the blends and the nanocomposites was evaluated by torque rheometer. The degree of dispersion of clay in the blend (polyamide 6 and PE) was evaluated by x-ray diffraction (XRD). In general, it was observed an increase in viscosity for the compositions containing the compatibilizer, and the results of XRD showed that the systems presented an intercalated and/or exfoliated structure. (author)

  2. Effect of Graphene Nanoplatelets (GNPs on Tribological and Mechanical Behaviors of Polyamide 6 (PA6

    Directory of Open Access Journals (Sweden)

    F. Mindivan

    2017-09-01

    Full Text Available The effects of Graphene Nanoplatelet (GNP on mechanical and tribological properties of Polyamide 6 (PA6 were studied. The composites were blended using twin-screw extruder and subsequently injection molded for test samples. Mechanical properties were investigated in terms of microhardness, scratch hardness and Young’s modulus measurements and tensile test. The tribological behavior of composites was studied by using ball-on-disc reciprocating tribometer. Recent studies showed that the addition of GNP in PA6 matrix resulted in enhancement of mechanical and tribological properties.

  3. In vitro antioxidant properties, free radicals scavenging activities of extracts and polyphenol composition of a non-timber forest product used as spice: Monodora myristica

    Directory of Open Access Journals (Sweden)

    Bruno Moukette Moukette

    2015-01-01

    Full Text Available BACKGROUND: Excessive production of free radicals causes direct damage to biological molecules such as DNA, proteins, lipids, carbohydrates leading to tumor development and progression. Natural antioxidant molecules from phytochemicals of plant origin may directly inhibit either their production or limit their propagation or destroy them to protect the system. In the present study, Monodora myristica a non-timber forest product consumed in Cameroon as spice was screened for its free radical scavenging properties, antioxidant and enzymes protective activities. Its phenolic compound profile was also realized by HPLC. RESULTS: This study demonstrated that M. myristica has scavenging properties against DPPH',OH',NO', and ABTS'radicals which vary in a dose depending manner. It also showed an antioxidant potential that was comparable with that of Butylated Hydroxytoluene (BHT and vitamin C used as standard. The aqueous ethanol extract of M. myristica barks (AEH; showed a significantly higher content in polyphenolic compounds (21.44 ±0.24 mg caffeic acid/g dried extract and flavonoid (5.69 ± 0.07 quercetin equivalent mg/g of dried weight as compared to the other studied extracts. The HPLC analysis of the barks and leaves revealed the presence of several polyphenols. The acids (3,4-OH-benzoic, caffeic, gallic, O- and P- coumaric, syringic, vanillic, alcohols (tyrosol and OH-tyrosol, theobromine, quercetin, rutin, catechine and apigenin were the identified and quantified polyphenols. All the tested extracts demonstrated a high protective potential on the superoxide dismutase (SOD, catalase and peroxidase activities. CONCLUSION: Finally, the different extracts from M. myristica and specifically the aqueous ethanol extract reveal several properties such as higher free radical scavenging properties, significant antioxidant capacities and protective potential effects on liver enzymes.

  4. A Geospatial Scavenger Hunt

    Science.gov (United States)

    Martinez, Adriana E.; Williams, Nikki A.; Metoyer, Sandra K.; Morris, Jennifer N.; Berhane, Stephen A.

    2009-01-01

    With the use of technology such as Global Positioning System (GPS) units and Google Earth for a simple-machine scavenger hunt, you will transform a standard identification activity into an exciting learning experience that motivates students, incorporates practical skills in technology, and enhances students' spatial-thinking skills. In the…

  5. Caracterização Mecânica de Compósitos de Poliamida/Fibra de Carbono Via Ensaios de Cisalhamento Interlaminar e de Mecânica da Fratura Mechanical Characterization of Polyamide/Carbon Fiber Composites by Using Interlaminar Shear Strength and Fracture Mechanical Tests

    Directory of Open Access Journals (Sweden)

    Edson C. Botelho

    2002-01-01

    Full Text Available Compósitos termoplásticos a partir de poliamidas 6 e 6,6 e tecido de fibras de carbono com 40, 50 e 60 % em volume de reforço foram processados via moldagem por compressão a quente e caracterizados por ensaios mecânicos destrutivos (cisalhamento interlaminar em três pontos (short-beam, cisalhamento interlaminar por compressão (CST e ensaios de mecânica da fratura e por inspeção não-destrutiva (ultra-som e microscopias óptica e eletrônica de varredura. Os resultados obtidos mostraram que os compósitos termoplásticos processados apresentaram uma distribuição homogênea do polímero no reforço. Entretanto, nos compósitos com maior quantidade de poliamida (40 % de reforço foram observadas regiões ricas em matriz entre as camadas de tecido. Os ensaios de mecânica da fratura (DCB e ENF e de cisalhamento interlaminar em três pontos não apresentaram falha interlaminar, não sendo observada a propagação de trincas de forma homogênea e retilínea no interior do material. Em função destes resultados foi utilizado o ensaio de cisalhamento por compressão, desenvolvido no Institute of Polymer Research Dresden da Alemanha, que permitiu uma caracterização mais precisa dos compósitos termoplásticos estudados. Foi observado também, a partir dos ensaios de CST, que os compósitos obtidos da poliamida 6,6 apresentaram um aumento no valor do cisalhamento interlaminar de até 20 % com o aumento do volume de fibras.Thermoplastics composites of polyamide 6 and 6.6 reinforced with carbon fiber fabric were obtained by compression molding and characterized by destructive (short-beam, compression shear (CST and fracture mechanics testing as well as by non-destructive inspection (ultrasound analysis, optical and scanning electron microscopy. The results show that, in general, the matrix was homogeneously distributed about the reinforcing fabric. However, for the composites with higher polyamide content (>50% matrix-rich regions were

  6. Synthesis and characterization of new soluble polyamides from Acenaphtohydrazinomercaptotriazole diamine

    Directory of Open Access Journals (Sweden)

    Hossein Mighani

    2015-08-01

    Full Text Available AbstractA diamine Acenaphtohydrazinomercaptotriazole (AHTD was synthesized in one step from acenaphthoqinone and 4-amino-3-hydrazino-5-mercapto-1,2,4-triazole. The diamin was characterized by FTIR, 1HNMR, 13CNMR and melting point. Diamin was used to prepare novel polyamides. The low temperature solution polycondensation of diamin with tow aromatic and tow aliphatic diacid chlorides afforded diamin-containing polyamides with inherent viscosities of 0.38–0.47 dl/g in DMF at 25 °C. The polyamides were generally soluble in a wide range of solvents such as dimethylformamide(DMF, N-Methylpyrolidone(NMP, tetrachloroethane (TCE, dimethylsulfoxide(DMSO and H2SO4. Thermal analysis showed that these polyamides were practically crustily and with Tg under 100 °C.

  7. Characterization and Solubilization of Pyrrole–Imidazole Polyamide Aggregates

    OpenAIRE

    Hargrove, Amanda E.; Raskatov, Jevgenij A.; Meier, Jordan L.; Montgomery, David C.; Dervan, Peter B.

    2012-01-01

    To optimize the biological activity of pyrrole–imidazole polyamide DNA-binding molecules, we characterized the aggregation propensity of these compounds through dynamic light scattering and fractional solubility analysis. Nearly all studied polyamides were found to form measurable particles 50–500 nm in size under biologically relevant conditions, while HPLC-based analyses revealed solubility trends in both core sequences and peripheral substituents that did not correlate with overall ionic c...

  8. Essential oil composition and isolation of freeradical-scavenging phenolic glycosides from the aerial parts of Ajuga chamaepitys growing in Iran

    Directory of Open Access Journals (Sweden)

    Abbas Delazar

    2012-04-01

    Full Text Available From the methanolic extract of the aerial parts of Ajuga chamaepitys (L. Schreb., Lamiaceae, one of the Iranian medicinal plants, the phenylethanoid glycoside, acteoside, and two flavone glycosides, chrysoeriol 7-O-glucopyranoside (3'-methoxy-luteolin 7-O-glucopyranoside and apigenin 7-O-rhamnopyranoside, were isolated by a combination of solid-phase extraction (SPE and preparative reversed-phase high-performance liquid chromatography (prep-RP-HPLC methods. Structures of the isolated compounds were elucidated by spectroscopic means. The free-radical-scavenging properties of the extracts, fractions and isolated compounds were determined by the 2,2-diphenyl-1-picryl-hydrazyl (DPPH assay. While among the extracts, the MeOH extract showed the highest level of free-radical-scavenging activity (RC50 1.15 × 10-1 mg/mL, chrysoeriol 7-O-glucopyranoside was the most active (RC50 3.00 × 10-3 mg/mL among the isolated compounds. The GC-MS and the GC-FID analyses revealed α-pinene (23.66%, β-pinene (9.33%, 1-octen-3-ol (9.72%, β-phellandrene (8.70% and germacrene-D (7.92% as the major components of the essential oils derived from the aerial parts of this plant. The presence of phenolic glycosides and the α- and β-pinene-rich essential oils in A. chamaepitys may provide some rationale for the traditional medicinal uses of this species in Iran.

  9. Essential oil composition and isolation of freeradical-scavenging phenolic glycosides from the aerial parts of Ajuga chamaepitys growing in Iran

    Directory of Open Access Journals (Sweden)

    Abbas Delazar

    2011-11-01

    Full Text Available From the methanolic extract of the aerial parts of Ajuga chamaepitys (L. Schreb., Lamiaceae, one of the Iranian medicinal plants, the phenylethanoid glycoside, acteoside, and two flavone glycosides, chrysoeriol 7-O-glucopyranoside (3'-methoxy-luteolin 7-O-glucopyranoside and apigenin 7-O-rhamnopyranoside, were isolated by a combination of solid-phase extraction (SPE and preparative reversed-phase high-performance liquid chromatography (prep-RP-HPLC methods. Structures of the isolated compounds were elucidated by spectroscopic means. The free-radical-scavenging properties of the extracts, fractions and isolated compounds were determined by the 2,2-diphenyl-1-picryl-hydrazyl (DPPH assay. While among the extracts, the MeOH extract showed the highest level of free-radical-scavenging activity (RC50 1.15 × 10-1 mg/mL, chrysoeriol 7-O-glucopyranoside was the most active (RC50 3.00 × 10-3 mg/mL among the isolated compounds. The GC-MS and the GC-FID analyses revealed α-pinene (23.66%, β-pinene (9.33%, 1-octen-3-ol (9.72%, β-phellandrene (8.70% and germacrene-D (7.92% as the major components of the essential oils derived from the aerial parts of this plant. The presence of phenolic glycosides and the α- and β-pinene-rich essential oils in A. chamaepitys may provide some rationale for the traditional medicinal uses of this species in Iran.

  10. Effect of Polyamide 6 on Crystalline Structure of Polymer in PVDF-Nanoclay Nanocomposite

    Directory of Open Access Journals (Sweden)

    Ali Akbar Yousefi

    2012-12-01

    Full Text Available The  effect  of  nanocaly  on  crystalline  structure  of  poly(vinylidene  fuoride, PVDF, and the morphology of the resulting nano-composite were investigated using  different  characterization  techniques.  The  presence  of  3wt%  Cloisite 30B in PVDF matrix results in 11 fold increase in the percentage of beta crystalline content of the polymer. This was found to be attributed to the epitaxial effect of the clay  surface. The  beta  crystalline  content  of  the  pure  polymer  (6% was  raised  to 68% in the composite. Addition of 5wt% polyamide 6 (PA6 improved dispersion of nanoclay which led to augmentation of the viscosity and displacement of the crossover frequency of the compatibilized composite towards lower frequencies. However, due to stronger affnity of the PA6 towards organically modifed clay the epitaxial effect of  the  clay on  crystalline  structure of PVDF was  totally  eliminated. The  reduction of  viscosity  in  incompatibilized  nanocomposite was  attributed  to  reduced  number of PVDF chain entanglements  in  the presence of nanoclay. Meanwhile,  increase  in viscosity and displacement of crossover  frequency  towards  lower  frequencies were attributed to formation of clay-PA nanoparticles and PVDF-polyamide 6 interactions. It is expected that the presence of polyamide 6 promotes the formation of oriented-beta crystals in PVDF, which in turn improves the piezoelectric properties of the polymer.

  11. The Development of Biomimetic Spherical Hydroxyapatite/Polyamide 66 Biocomposites as Bone Repair Materials

    Directory of Open Access Journals (Sweden)

    Xuesong Zhang

    2014-01-01

    Full Text Available A novel biomedical material composed of spherical hydroxyapatite (s-HA and polyamide 66 (PA biocomposite (s-HA/PA was prepared, and its composition, mechanical properties, and cytocompatibility were characterized and evaluated. The results showed that HA distributed uniformly in the s-HA/PA matrix. Strong molecule interactions and chemical bonds were presented between the s-HA and PA in the composites confirmed by IR and XRD. The composite had excellent compressive strength in the range between 95 and 132 MPa, close to that of natural bone. In vitro experiments showed the s-HA/PA composite could improve cell growth, proliferation, and differentiation. Therefore, the developed s-HA/PA composites in this study might be used for tissue engineering and bone repair.

  12. Flame retardancy of highly filled polyamide 6/clay nanocomposites

    International Nuclear Information System (INIS)

    Dasari, Aravind; Yu Zhongzhen; Mai Yiuwing; Liu Songlin

    2007-01-01

    To obtain an in-depth physical knowledge of the protective barrier stability and uniformity under fire conditions, we prepared highly filled polyamide 6/organoclay nanocomposites and characterized their thermal and flammability properties. The objectives were to identify a critical composition that is needed to form a stable char with no apertures or cracks and to gain a thorough understanding of the mechanisms of flame retardancy. It was shown that there is no need for higher percentages of clay and even smaller amounts of clay (<10 wt%) should be enough to achieve good fire performance. Factors such as incoherency, poor stability and non-uniformity of the char or the presence of large cracks and formation of island-like structures were insignificant in slowing down the heat release and mass loss rates. Nevertheless, there was no stage during the flammability test where the fire completely extinguished even when the protective layer was stable and free from major cracks/apertures. Based on these results, new insights and approaches to process better flame retardant polymer nanocomposites are discussed

  13. Antibacterial Properties of Functional Polyamide 6.6

    Directory of Open Access Journals (Sweden)

    El Bouchti Mehdi

    2014-06-01

    Full Text Available Polyamide 6.6 multifilaments are grafted with the monomer N-allyliminodiacetic acid for the purpose of removal of some heavy metal ions from their aqueous solutions by forming its metal chelate especially with Ag+ ion. Such a fibrous chelate-forming resin has been used with success due to its large surface area, which contains an important metal chelate-forming functional group, where metal ions are adsorbed or desorbed on its surface, and therefore having an improved adsorption and desorption capability. In previous work, chelate-forming fibre was characterised by ICP-AES analysis according to the digestion method by microwave. The antibacterial activity of the prepared fibre is investigated with Escherichia coli bacteria as reference, according to the zone of inhibition method in agar medium. The material used as reference without metal does not present any effect on E. coli. However, the chelateforming fibres with Ag+ have a strong bactericidal effect, even with a low concentration of silver ions. These modified materials can be used as highly effective bactericidal composites that may be used in future applications for the production of antimicrobial textiles, papers or polymer materials

  14. Irradiation effects on properties of reverse osmosis membrane based on cross-linked aromatic polyamide

    International Nuclear Information System (INIS)

    Nakase, Yoshiaki; Yanagi, Tadashi; Uemura, Tadahiro.

    1994-01-01

    In order to develop a membrane suitable for reverse osmotic condensation of radioactive liquid wastes, a new cross-linked aromatic polyamide composite reverse osmosis membrane (ROM) was irradiated in water or in wet system, and its mechanical and some thermal properties, and the separation performance for inorganic salt were investigated. A membrane was degraded by irradiation more severely in wet system than in dry system, probably due to the reaction with OH-radicals. In the separation performance for NaCl, the salt rejection of the membrane was kept over 88% until irradiation reached 2MGy, maintaining about 90% of its original water flux. (author)

  15. Synthesis and characterization of lead oxides for preparation of nanocomposites with polyamide

    International Nuclear Information System (INIS)

    Cado, Ronan Gorski; Severo, Vinicius A.; Bulhores, Luis Otavio S.

    2016-01-01

    Lead oxide nanoparticles with diameters between 100 to 250 nm were obtained using a polymeric precursor method in the presence of citric acid and ethylene glycol. X-ray diffraction (XRD) and dynamic light scattering to measure the size and zeta potential in solution in dispersions with different pH were used to characterize the as-obtained samples. The nanoparticles were incorporated into polyamide 6.6 and composite films were prepared by electrospinning being evaluated the variation of the mechanical properties of the polymer and its effectiveness in attenuation of X-rays. (author)

  16. Improvement of surface wettability and interfacial adhesion of poly-(p-phenylene terephthalamide) by incorporation of the polyamide benzimidazole segment

    International Nuclear Information System (INIS)

    Cai Renqin; Peng Tao; Wang Fengde; Ye Guangdou; Xu Jianjun

    2011-01-01

    In order to investigate the effect of the polyamide benzimidazole group on the surface wettability and interfacial adhesion of fiber/matrix composites, surface features of two kinds of aramid fibers, poly (p-phenylene terephthalamide) fiber (Kevlar-49) and poly-(polyamide benzimidazole-co-p-phenylene terephthalamide) (DAFIII), have been analyzed by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and contact angle analysis (CAA) system, respectively. The results show that with the incorporation of the polyamide benzimidazole segment, more polar functional groups exist on DAFIII surface. The contact angles of water and diiodomethane on DAFIII surface get smaller. The surface free energy of DAFIII increases to 36.5 mJ/m 2 , which is 2.3% higher than that of Kevlar-49. In addition, DAFIII has a larger rough surface compared with that of Kevlar-49 due to different spinning processes. The interfacial shear strength (IFSS) of DAFIII/matrix composite is 25.7% higher than that of Kevlar-49/matrix composite, in agreement with the observed results from surface feature tests. SEM micrographs of failed micro-droplet specimens reveal a strong correlation between the fracture features and the observed test data.

  17. Living Polycondensation: Synthesis of Well-Defined Aromatic Polyamide-Based Polymeric Materials

    KAUST Repository

    Alyami, Mram Z.

    2016-01-01

    Chain growth condensation polymerization is a powerful tool towards the synthesis of well-defined polyamides. This thesis focuses on one hand, on the synthesis of well-defined aromatic polyamides with different aminoalkyl pendant groups with low

  18. Effects of Green Tea Extract on Physicochemical and Antioxidant Properties of Polyamide Packaging Film

    OpenAIRE

    Ali Asghar Barzegaran; Maryam Jokar; Majid Javanmard Dakheli

    2014-01-01

    Polyamide 6 has been widely used in food packaging applications and also green tea contains amounts of antioxidant compounds. The aim of this study was investigation of green tea effects on properties of polyamide packaging polymer. Polyamide 6 was dissolved in methanol which was saturated with calcium chloride. The active packaging film was produced by incorporation of methanol green tea extracts at levels of 2.5, 5, 10 and 20% in polyamide solution by solution casting method. Mechanical and...

  19. Machining of glass fiber reinforced polyamide

    Directory of Open Access Journals (Sweden)

    2007-12-01

    Full Text Available The machinability of a 30 wt% glass fiber reinforced polyamide (PA was investigated by means of drilling tests. A disk was cut from an extruded rod and drilled on the flat surface: thrust was acquired during drilling at different drilling speed, feed rate and drill diameter. Differential scanning calorimetry (DSC and indentation were used to characterize PA so as to evaluate the intrinsic lack of homogeneity of the extruded material. In conclusion, it was observed that the chip formation mechanism affects the thrust dependence on the machining parameters. A traditional modeling approach is able to predict thrust only in presence of a continuous chip. In some conditions, thrust increases as drilling speed increases and feed rate decreases; this evidence suggests not to consider the general scientific approach which deals the machining of plastics in analogy with metals. Moreover, the thrust can be significantly affected by the workpiece fabrication effect, as well as by the machining parameters; therefore, the fabrication effect is not negligible in the definition of an optimum for the machining process.

  20. Obtenção de um revestimento compósito de poliéster-uretana reforçado com alumina pela técnica de deposição por imersão sobre fibras de poliamida 6 Preparation of a composite coating of alumina reinforced polyester urethane by dip coating on polyamide 6 fibers

    Directory of Open Access Journals (Sweden)

    F. A. L. Sánchez

    2009-12-01

    Full Text Available O uso de revestimentos compósitos de matriz polimérica e reforço cerâmico capazes de manter a flexibilidade e a elasticidade das fibras poliméricas, agregando propriedades típicas dos materiais cerâmicos (como ação bactericida ou fotocatalítica, resistência à chama, ao desgaste e à abrasão, tem atraído interesse da indústria têxtil. Baseado na técnica dip coating e usando fibras sintéticas de poliamida como substrato, foram produzidas suspensões de poliéster-uretana com partículas de alumina (tamanho médio de partícula 2,2 μm para obtenção de revestimentos uniformes e espessos sobre o material base, poliamida 6. A viscosidade das suspensões foi controlada pela adição de carboximetilcelulose e avaliada por reometria rotacional. A distribuição granulométrica das suspensões também foi determinada. Os parâmetros operacionais do dip coating, i.e., velocidade de bobinamento e temperatura dos fornos, foram mantidos constantes em todas as amostras. O processo mostrou viabilidade para deposição uniforme do recobrimento avaliado, com espessura adequada, indicando ser promissor para revestir fibras, agregando propriedades de interesse tecnológico.Ceramic reinforced polymer composite coatings that can retain the flexibility and elasticity of the polymeric fibers, being also able to incorporate the functionality of ceramic materials (e.g. fire, wear, or abrasion resistance, antibacterial performance, photocatalytic effect are interesting to the processing of textile materials. In this work, polyester-urethane slurries with alumina particles (mean particle size: 2.2 μm were developed based on the dip coating technique and using polyamide-6 synthetic fibers as the substrate, seeking to obtain an uniform and thick coating. The viscosity of the slurries was varied using carboxymethylcellulose as a rheological agent and evaluated by rotational rheometry. Particle size distribution of the slurries was also analyzed. The

  1. Development of polyamide-6/chitosan membranes for desalination

    Directory of Open Access Journals (Sweden)

    A. EL-Gendi

    2014-06-01

    Full Text Available This article deals with “developing novel polyamide-6/chitosan membranes for water desalting using wet phase inversion technique”, in which novel polyamide-6/chitosan membranes were prepared using an appropriate polymer concerning the national circumferences, along with the definition of different controlling parameters of the preparing processes and their effects on the characteristics of the produced membranes. Further, evaluation process of the fabricated sheets was undertaken. Preparation process was followed by assessment of the membrane structural characteristics; then the desalting performance of each prepared membrane was evaluated under different operating conditions in order to find the structure–property relationship. The results show that the membrane flux increases with the increase of operating pressure. The salt rejection and permeation flux have been enhanced this indicates that the chitosan (CS addition to the polyamide-6 (PA-6 membrane increases the membrane hydrophilic property. Hydraulic permeability coefficient is not stable and varies considerably with the operating pressure.

  2. Organobasierter Sauerstoff-Scavenger/-Indikator

    OpenAIRE

    Langowski, H.C.; Wanner, T.

    2007-01-01

    WO 2007059901 A1 UPAB: 20070911 NOVELTY - Oxygen scavenger/indicator which contains at least one substance having combined scavenging and indicating functions for oxygen which is capable of absorbing oxygen under the effect of moisture in alkaline conditions, and at least one alkaline compound. The indicator effect is caused by a change in at least one physical property of the substance having combined scavenging and indicating function for oxygen, the change being initiated by the presence o...

  3. Toughened nanocomposites of polyamide-6 and polyepichlorohydrin elastomer: mechanical and morphological properties

    International Nuclear Information System (INIS)

    Pinotti, Caio A.; Goncalves, Maria C.; Felisberti, Maria I.

    2009-01-01

    Blends of polyamide 6, P A6, and polyepichlorohydrin elastomer, PE Pi, nano composites of P A6 and OMMT and toughened nano composites, P A6/PE Pi/OMMT were prepared by twin-screw extrusion. Nanocomposites of P A6 and organophilic clay presented morphology of exfoliated clay with the presence of some tactoids, which were investigated by XRD and TEM. The blends P A6/PE Pi are immiscible with morphology of elastomer disperse phase. The size of the elastomer phase in the PA6 matrix and a better distribution of these phase were achieved with the incorporation of the clay in the ternary nanocomposites. Toughened nano composites presented increases in Young's modulus, Izod impact strength and yield stress, comparing with the blends of P A6 and polyepichlorohydrin elastomer. (author)

  4. Irradiation Crosslinking of Polyamides for the Electrical and Automotive Industry

    International Nuclear Information System (INIS)

    Gehring, J.

    2006-01-01

    Irradiation crosslinking of electrical cables and heat shrinkable tubes have been widely accepted in the automotive and electrical industry for a long time. Due higher demands regarding temperature resistance, arc resistance and good chemical resistance against oil and greases crosslinked injection moulded parts made out of polyamid and polybutylentherephtalate become also more and more interesting. Crosslinked polyamide can also replace thermosets for switches and offers therefore additional financial benefits. It will be shown on the basis of already realized projects, which basic requirements exist and how irradiation crosslinking can fulfil these demands

  5. Fabrication of Electrospun Polyamide-6/Chitosan Nanofibrous Membrane toward Anionic Dyes Removal

    Directory of Open Access Journals (Sweden)

    Mozhdeh Ghani

    2014-01-01

    Full Text Available Nanofibrous filter media of polyamide-6/chitosan were fabricated by electrospinning onto a satin fabric substrate and characterized by scanning electron microscopy (SEM, Fourier transform infrared spectroscopy (FTIR, and water contact angle (WCA. Anionic dye removal capability of the filter was investigated for Solophenyl Red 3BL and Polar Yellow GN, respectively, as acidic and direct dyes were investigated with respect to solution parameters (pH and initial dye concentration and membrane parameters (electrospinning time and chitosan ratio through filtration system. Experiments were designed using response surface methodology (RSM based on five-level central composite design (CCD with four parameters to maximize removal efficiency of the filter media. Moreover, the effect of parameters and their likely interactions on dye removal were investigated by mathematically developed models. The optimum values for solution pH, initial dye concentration, electrospinning time, and chitosan ratio were predicted to be 5, 50 mg/L, 4 hr, 30% and 5, 100 mg/L, 4 hr, 10%, respectively, for achieving 96% and 95% removal of Solophenyl Red 3BL and Polar Yellow GN. Evaluation of the estimation capability of applied models revealed that the models have a good agreement with experimental values. This study demonstrated that polyamide-6/chitosan nanofibrous membrane has an enormous applicable potential in dye removal from aqueous solutions.

  6. A study of thermal reactions of coal with polyamides

    Czech Academy of Sciences Publication Activity Database

    Straka, Pavel; Náhunková, Jana

    2004-01-01

    Roč. 1, č. 2 (2004), s. 239-243 ISSN 1211-1910 R&D Projects: GA AV ČR IAA2046902 Institutional research plan: CEZ:AV0Z3046908 Keywords : coal * kinetics * polyamides Subject RIV: CD - Macromolecular Chemistry

  7. The study of epoxy polyamide and polyvinyl resins as corrosion ...

    African Journals Online (AJOL)

    The corrosion resistance of two commonly used protective coatings (epoxy polyamide and polyvinyl resins) in the Niger Delta area of Nigeria has been assessed. The coatings on low carbon steel were subjected to varying conditions of pH, temperature and exposure time and the corrosion rates calculated. At a pH of 2, 3, 4, ...

  8. Microporous membranes from polyolefin-polyamide blend materials

    Czech Academy of Sciences Publication Activity Database

    Meier-Haack, J.; Valko, M.; Lunkwitz, K.; Bleha, Miroslav

    2004-01-01

    Roč. 163, 1-3 (2004), s. 215-221 ISSN 0011-9164. [Membrane Science and Technology Conference PERMEA 2003. Tatranské Matliare, 07.09.2003-11.09.2003] Institutional research plan: CEZ:AV0Z4050913 Keywords : microporous membranes * polypropylene polyamide blends * reactive extrusion Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.057, year: 2004

  9. 3D morphological characterization of the polyamide active layer of RO and NF membranes using TEM and soft X-ray scattering

    Science.gov (United States)

    Culp, Tyler; Paul, Mou; Roy, Abhishek; Rosenberg, Steve; Behr, Michael; Kumar, Manish; Gomez, Enrique; Penn State Team; Dow Team

    Polyamide-based thin-film composite (TFC) membranes used for reverse osmosis (RO) and nanofiltration (NF) separation processes are at the forefront of water desalination and purification technologies due to their high salt rejection, high energy efficiency, and ease of operation. Nevertheless, in spite of the benefits of RO and NF membranes, many open questions about the internal nanostructure of the membrane active layer remain, such as the dispersion and distribution of acid functional groups. We demonstrate that resonant soft X-ray scattering (RSOXS), where the X-ray energy is tuned to absorption edges of the constituent materials, is a powerful tool to examine the microstructure of the polyamide layer. In conjunction with complementary techniques such as transmission electron microscopy (TEM), where tomography is used to obtain a 3D reconstruction of the polyamide active layer, the effect of cross-linking can be quantified in 3D for a systematic series of membranes. This relationship can then be applied to a series of commercially available RO and NF membranes where the effect of polyamide cross-linking on their respective structure and water transport properties can be evaluated. The combination of RSOXS with traditional characterization tools provides a strategy for linking the chemical structure to the morphology and water transport properties of RO and NF membranes.

  10. Winery by-products: extraction optimization, phenolic composition and cytotoxic evaluation to act as a new source of scavenging of reactive oxygen species.

    Science.gov (United States)

    Melo, Priscilla Siqueira; Massarioli, Adna Prado; Denny, Carina; dos Santos, Luciana Ferracini; Franchin, Marcelo; Pereira, Giuliano Elias; Vieira, Thais Maria Ferreira de Souza; Rosalen, Pedro Luiz; de Alencar, Severino Matias

    2015-08-15

    Nearly 20 million tons of winery by-products, with many biological activities, are discarded each year in the world. The extraction of bioactive compounds from Chenin Blanc, Petit Verdot, and Syrah grape by-products, produced in the semi-arid region in Brazil, was optimized by a Central Composite Rotatable Design. The phenolic compounds profile, antioxidant capacity against synthetic free radicals (DPPH and ABTS), reactive oxygen species (ROS; peroxyl radical, superoxide radical, hypochlorous acid), cytotoxicity assay (MTT) and quantification of TNF-α production in RAW 264.7 cells were conducted. Gallic acid, syringic acid, procyanidins B1 and B2, catechin, epicatechin, epicatechin gallate, quercetin 3-β-d-glucoside, delfinidin 3-glucoside, peonidin 3-O-glucoside, and malvidin 3-glucoside were the main phenolic compounds identified. In general, rachis showed higher antioxidant capacity than pomace extract, especially for Chenin Blanc. All extracts showed low cytotoxicity against RAW 264.7 cells and Petit Verdot pomace suppressed TNF-α liberation in vitro. Therefore, these winery by-products can be considered good sources of bioactive compounds, with great potential for application in the food and pharmaceutical industries. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Effects of Green Tea Extract on Physicochemical and Antioxidant Properties of Polyamide Packaging Film

    Directory of Open Access Journals (Sweden)

    Ali Asghar Barzegaran

    2014-08-01

    Full Text Available Polyamide 6 has been widely used in food packaging applications and also green tea contains amounts of antioxidant compounds. The aim of this study was investigation of green tea effects on properties of polyamide packaging polymer. Polyamide 6 was dissolved in methanol which was saturated with calcium chloride. The active packaging film was produced by incorporation of methanol green tea extracts at levels of 2.5, 5, 10 and 20% in polyamide solution by solution casting method. Mechanical and barrier properties of polyamide films were investigated using ASTM standards and antioxidant activity of polyamide films was evaluated using DPPH method. Results indicated that green tea extract increased antioxidant properties and tensile and young modulus of polyamide films. Oxygen and water vapor permeability of films were decreased by incorporation of green tea extract into polyamide matrix. Green tea extract improved barrier and tensile properties of polyamide films, however elongation at break reduced as increasing of green tea extract in polyamide-based films significantly (P<0.05.

  12. Method for scavenging mercury

    Science.gov (United States)

    Chang, Shih-ger [El Cerrito, CA; Liu, Shou-heng [Kaohsiung, TW; Liu, Zhao-rong [Beijing, CN; Yan, Naiqiang [Berkeley, CA

    2009-01-20

    Disclosed herein is a method for removing mercury from a gas stream comprising contacting the gas stream with a getter composition comprising bromine, bromochloride, sulphur bromide, sulphur dichloride or sulphur monochloride and mixtures thereof. In one preferred embodiment the getter composition is adsorbed onto a sorbent. The sorbent may be selected from the group consisting of flyash, limestone, lime, calcium sulphate, calcium sulfite, activated carbon, charcoal, silicate, alumina and mixtures thereof. Preferred is flyash, activated carbon and silica.

  13. Efeito da forma de processamento e do tratamento da fibra de curauá nas propriedades de compósitos com poliamida-6 Effect of the processing method and curauá fiber treatment on the properties of polyamide-6 composites

    Directory of Open Access Journals (Sweden)

    Paulo A. Santos

    2009-01-01

    Full Text Available O interesse pela utilização de fibras vegetais como reforço para polímeros tem aumentado recentemente devido às suas vantagens ambientais e tecnológicas. Este trabalho avaliou o uso de fibras de Curauá para substituir a fibra de vidro em compósitos de poliamida-6. Teores de fibra de 0, 20, 30 ou 40 wt% e comprimento de 0,1 ou 10 mm foram analisados. Parte das fibras foi tratada com plasma de N2 ou lavados com solução de NaOH, para melhorar a adesão fibra/matriz. Compósitos com 20 wt% de fibra curta ou longa, sem ou com pré-tratamento, foram preparados em misturador interno e em duas extrusoras dupla-rosca, co-rotantes, interpenetrantes. Corpos de prova destas amostras moldados por injeção foram submetidos a testes de propriedades mecânicas (tração, flexão e impacto e térmicas (HDT. Observou-se que para as amostras com fibras sem tratamento processadas em extrusora, a não-secagem das matérias-primas melhorou a adesão interfacial fibra/matriz e que as propriedades mecânicas destes compósitos são melhores que a da PA-6 sem reforço, mas ainda não superam a PA-6 reforçada com fibra de vidro. Entretanto, sua menor densidade, sua resistência ao impacto, temperatura de deflexão térmica e contração de moldagem, comparáveis às da PA-6 reforçada com fibra de vidro, podem viabilizar a substituição desta em aplicações específicas. Este foi o primeiro trabalho a estudar o uso de fibra de curauá como reforço de um termoplástico de engenharia como a poliamida-6.The interest for the use of vegetal fibers as polymer reinforcement has recently increased because of their unique environmental and technological advantages. This work evaluated the use of Curauá fibers in polyamide-6 composites, aiming at glass fiber replacement. Fiber contents of 0, 20, 30 and 40 wt% and fiber lengths of 0.1 or 10 mm were analyzed. Part of short fibers were treated with N2 plasma, or washed with NaOH solution, to improve their adhesion to

  14. Tumor Repression of VCaP Xenografts by a Pyrrole-Imidazole Polyamide.

    Directory of Open Access Journals (Sweden)

    Amanda E Hargrove

    Full Text Available Pyrrole-imidazole (Py-Im polyamides are high affinity DNA-binding small molecules that can inhibit protein-DNA interactions. In VCaP cells, a human prostate cancer cell line overexpressing both AR and the TMPRSS2-ERG gene fusion, an androgen response element (ARE-targeted Py-Im polyamide significantly downregulates AR driven gene expression. Polyamide exposure to VCaP cells reduced proliferation without causing DNA damage. Py-Im polyamide treatment also reduced tumor growth in a VCaP mouse xenograft model. In addition to the effects on AR regulated transcription, RNA-seq analysis revealed inhibition of topoisomerase-DNA binding as a potential mechanism that contributes to the antitumor effects of polyamides in cell culture and in xenografts. These studies support the therapeutic potential of Py-Im polyamides to target multiple aspects of transcriptional regulation in prostate cancers without genotoxic stress.

  15. Polyamide 6/clay membranes: effect of precipitation bath in morphology

    International Nuclear Information System (INIS)

    Ferreira, Rodholfo da S.B.; Pereira, Caio H. do O; Leite, Amanda M.D.; Araujo, Edcleide M.; Lira, Helio L.

    2015-01-01

    Polyamide 6 membranes and their nanocomposites with 5% clay were obtained by the phase inversion method and the precipitation was made in distilled water bath and also in the mixture of solvent and distilled water. The nanocomposites were characterized by XRD and membranes by SEM. By XRD analysis, it was found that the obtained nanocomposite presents a structure probably exfoliated and / or partially exfoliated, it was also possible to observe the presence of two characteristic peaks (α and γ) of the polyamide 6 phases. In the SEM micrographs it was seen that the presence of clay promote alterations in morphology, size and distribution of pores. The presence of acid in the precipitation bath leads to a significant decrease in the filter layer, but also an increase in the quantity of pore size. (author)

  16. Evaluation of impact strength of polyamide 6/bentonite clay nanocomposites

    International Nuclear Information System (INIS)

    Paz, Rene A.; Leite, Amanda M.D.; Medeirosa, Vanessa da N.; Araujo, Edcleide M.; Melo, Tomas J.A.; Pessan, Luiz A.

    2010-01-01

    Nanocomposites of polymer/clay have had much attention in recent years, particularly those developed with layered silicates due to the need of engineering materials more efficient than pure polymers for certain applications. The level of exfoliation of layered silicates in crystalline structure of polymer matrices has been studied and has been observed that they affect the crystalline behavior and the physical and mechanical properties. In this study, nanocomposites of polyamide 6 were obtained by the melt intercalation method, using a regional bentonite modified with a quaternary ammonium salt in an amount of 3% by weight. XRD results showed that incorporation of salt among the layers of clay, making it organophilic and obtaining exfoliated and/or partially exfoliated structures. The impact properties of the nanocomposites showed inferior in relation to pure polyamide, in other words, lost of toughness. (author)

  17. Investigation into radiation-chemical transformations of polyamide P-54

    International Nuclear Information System (INIS)

    Khabarov, V.N.; Kozlov, L.L.; Panchenkov, G.M.

    1981-01-01

    Investigation results of alcohol-soluble polyamide P-54 radiolysis by different physicochemical methods are presented. It has been established that under the effect of γ-radiation certain processes take place in polyamide, which are connected with branching, structurization and destruction of macromolecules. Radiation-chemical yields of gaseous products during irradiation in the air and in vacuum at irradiation temperatures from 273 to 393 K are calculated. The ratio of the rates of lacing and destruction processes is found and radiation yields of the processes are determined. Under irradiation in the air at temperatures >333 K chain oxidation of P-54 takes place and the growth of pe-- roxide compounds with 8 molecules/100 eV at 298 K up to 135 mole-- cules/100 eV at irradiation temperature 373 K testifies to the fact

  18. Tumor Repression of VCaP Xenografts by a Pyrrole-Imidazole Polyamide

    OpenAIRE

    Hargrove, Amanda E.; Martinez, Thomas F.; Hare, Alissa A.; Kurmis, Alexis A.; Phillips, John W.; Sud, Sudha; Pienta, Kenneth J; Dervan, Peter B.

    2015-01-01

    Pyrrole-imidazole (Py-Im) polyamides are high affinity DNA-binding small molecules that can inhibit protein-DNA interactions. In VCaP cells, a human prostate cancer cell line overexpressing both AR and the TMPRSS2-ERG gene fusion, an androgen response element (ARE)-targeted Py-Im polyamide significantly downregulates AR driven gene expression. Polyamide exposure to VCaP cells reduced proliferation without causing DNA damage. Py-Im polyamide treatment also reduced tumor growth in a VCaP mouse ...

  19. Synthesis and Characterization of New Polyamides from 1,2-Bis hydrazine Derivatives

    International Nuclear Information System (INIS)

    Salaha, A.; Abdel-Bary, E.M.; Kandilea, N.G.

    2005-01-01

    Preparation of polyamides having different chemical structures allows obtaining new materials with different mechanical and physical properties. The difference in the chemical structure depends mainly on the starting reactants used in condensation polymerization of polyamides. In this paper the synthesis of new polyamides based on the condensation polymerization of 1,2- Bis(3-carboxyacryloyl or carboxybenzoyl) hydrazine derivatives and various diamines has been described. The polymers obtained were characterized using spectroscopic and X-ray analysis. Besides thermal stability and electrical conductivity have been evaluated and correlated with the chemical structure of the polyamides obtained

  20. Kinetics of copyrolysis of coal with polyamide 6

    Czech Academy of Sciences Publication Activity Database

    Straka, Pavel; Náhunková, Jana; Brožová, Zuzana

    2004-01-01

    Roč. 71, č. 1 (2004), s. 213-221 ISSN 0165-2370. [Pyrolysis 2002, 15th International Symposium on Analytical and Applied Pyrolysis. Leoben, 17.09.2002-20.09.2002] R&D Projects: GA AV ČR IBS3046004 Institutional research plan: CEZ:AV0Z3046908 Keywords : coal * kinetics * polyamide 6 Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.352, year: 2004

  1. Factors affecting polyamide prototypes design of Albedo dosemeters

    International Nuclear Information System (INIS)

    Martins, M.M.; Mauricio, C.L.P.; Fonseca, E.S.

    1996-01-01

    This work studies the most important factors which affect the response of albedo neutron dosemeters containing LiF TLDs with the aim to improve their sensitivity. It includes tests of thickness and shape of the polyamide moderator body prototypes, albedo window diameter and TLD position inside the moderator. Analyzing the results, an albedo neutron dosemeter prototype, B 4 C covered, was developed. The prototype has a response three times higher than the albedo dosemeter now in use in Brazil. (author)

  2. Evaluation of impact strength of polyamide 6/bentonite clay nanocomposites

    International Nuclear Information System (INIS)

    Paz, Rene Anisio; Araujo, Edcleide Maria; Tomas Jeferson Alves; Amanda Damiao; Medeiros, Vanessa da Nobrega; Pessan, Luiz Antonio

    2012-01-01

    Nanocomposites of polymer/clay have had much attention in recent years, particularly those developed with layered silicates due to the need of engineering materials more efficient than pure polymers for certain applications. The level of exfoliation of layered silicates in crystalline structure of polymer matrices has been studied and has been observed that it affects the crystalline behavior and the physical and mechanical properties. In this study, nanocomposites of polyamide 6 were obtained by the melt intercalation method, using a Brazilian bentonite modified with a quaternary ammonium salt. X-Ray Diffraction (XRD) results showed the incorporation of salt among the layers of clay, making it organophilic and that the nanocomposites presented exfoliated and/or partially exfoliated structures and confirmed by transmission electron microscopy (TEM). By thermogravimetry (TG), the results indicated that the presence of clay increased the thermal stability of polyamide 6. The impact properties of the nanocomposites showed inferior values in relation to the pure polyamide, in other words, decrease the toughness. (author)

  3. Structure and mechanical properties of polyamide 6/Brazilian clay nanocomposites

    Directory of Open Access Journals (Sweden)

    Amanda Melissa Damião Leite

    2009-06-01

    Full Text Available Recent interest in polymer/organoclays nanocomposites systems is motivated by the possibility of achieving enhanced properties and added functionality at lower clay loading as compared to conventional micron size fillers. By adding montmorillonite clay to polyamide 6 increases the Young modulus, yield strength and also improves barrier properties. In this work, nanocomposites of polyamide 6 with montmorillonite clay were obtained. The clay was chemically modified with three different quaternary ammonium salts such as: Dodigen, Genamin and Cetremide. In this case, a dispersion of Na-MMT was stirred and a salt equivalent to 1:1 of cation exchange capacity (CEC of Na-MMT was added to the dispersion. The montmorillonite clay (untreated and treated by ammonium salts and nanocomposites were characterized by X ray diffractions. Also the nanocomposites were characterized by transmission electron microscopy and mechanical properties. The results indicated that all the quaternary ammonium salts were intercalated between the layers of clay, leading to an expansion of the interlayer spacing. The obtained nanocomposites showed better mechanical properties when compared to polyamide 6. The clay acted as reinforcing filler, increasing the rigidity of nanocomposites and decreasing its ductility.

  4. Synthesis and Properties of Cross-Linked Polyamide Aerogels

    Science.gov (United States)

    Williams, Jarrod C.; Meador, Mary Ann; McCorkle, Linda

    2015-01-01

    We report the first synthesis of cross-linked polyamide aerogels through step growth polymerization using a combination of diamines, diacid chloride and triacid chloride. Polyamide oligomers endcapped with amines are prepared as stable solutions in N-methylpyrrolidinone from several different diamine precursors and 1,3-benzenedicarbonyl dichloride. Addition of 1,3,5-benzenetricarbonyl trichloride yields gels which form in under five minutes according to the scheme shown. Solvent exchange of the gels into ethanol, followed by drying using supercritical CO2 extraction gives colorless aerogels with densities around 0.1 to 0.2 gcm3. Thicker monolithes of the polyamide aerogels are stiff and strong, while thin films of certain formulations are highly flexible, durable, and even translucent. These materials may have use as insulation for deployable space structures, rovers, habitats or extravehicular activity suits as well as in many terrestrial applications. Strucure property relationships of the aerogels, including surface area, mechanical properties, and thermal conductivity will be discussed.

  5. Evaluation of impact strength of polyamide 6/bentonite clay nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Paz, Rene Anisio; Araujo, Edcleide Maria; Tomas Jeferson Alves; Amanda Damiao; Medeiros, Vanessa da Nobrega [Federal University of Campina Grande (CCT/UFCG), Campina Grande, PB (Brazil). Centro de Ciencias e Tecnologia; Pessan, Luiz Antonio [Federal University of Sao Carlos (DEMa/UFSCar), SP (Brazil). Materials Engineering Department

    2012-07-15

    Nanocomposites of polymer/clay have had much attention in recent years, particularly those developed with layered silicates due to the need of engineering materials more efficient than pure polymers for certain applications. The level of exfoliation of layered silicates in crystalline structure of polymer matrices has been studied and has been observed that it affects the crystalline behavior and the physical and mechanical properties. In this study, nanocomposites of polyamide 6 were obtained by the melt intercalation method, using a Brazilian bentonite modified with a quaternary ammonium salt. X-Ray Diffraction (XRD) results showed the incorporation of salt among the layers of clay, making it organophilic and that the nanocomposites presented exfoliated and/or partially exfoliated structures and confirmed by transmission electron microscopy (TEM). By thermogravimetry (TG), the results indicated that the presence of clay increased the thermal stability of polyamide 6. The impact properties of the nanocomposites showed inferior values in relation to the pure polyamide, in other words, decrease the toughness. (author)

  6. POLYAMIDE 6 WITH A FLAME RETARDANT ENCAPSULATED BY POLYAMIDE 66: FLAME RETARDATION, THERMO-DECOMPOSITION AND THE POTENTIAL MECHANISM

    Institute of Scientific and Technical Information of China (English)

    Wei-cheng Xiong; Li Chen; Bin Zhao; De-yi Wang; Yu-zhong Wang

    2012-01-01

    A novel encapsulated flame retardant containing phosphorus-nitrogen (MSMM-Al-P) was prepared by encapsulating with polyamide 66 (PA66-MSMM-Al-P) for the flame retardation of polyamide 6 (PA6).The structure and thermal properties of PA66-MSMM-Al-P were characterized by Fourier-transform infrared spectroscopy,X-ray photoelectron spectroscopy and thermogravimetric analysis.The flammability of PA6 containing' flame retardants (MSMMAl-P and PA66-MSMM-Al-P) was investigated by the limiting oxygen index test,vertical burning test and cone calorimeter.The flame retardancy and cone calorimetric analyses suggested a synergistic effect between PA66 and MSMM-Al-P in the flame-retardant PA6.Thermal stability of the flame-retardant PA6 was also investigated.

  7. High Performance Thin-Film Composite Forward Osmosis Membrane

    KAUST Repository

    Yip, Ngai Yin; Tiraferri, Alberto; Phillip, William A.; Schiffman, Jessica D.; Elimelech, Menachem

    2010-01-01

    obstacle hindering further advancements of this technology. This work presents the development of a high performance thin-film composite membrane for forward osmosis applications. The membrane consists of a selective polyamide active layer formed

  8. Synergistically improved thermal conductivity of polyamide-6 with low melting temperature metal and graphite

    Directory of Open Access Journals (Sweden)

    Y. C. Jia

    2016-08-01

    Full Text Available Low melting temperature metal (LMTM-tin (Sn was introduced into polyamide-6 (PA6 and PA6/graphite composites respectively to improve the thermal conductivity of PA6 by melt processing (extruding and injection molding. After introducing Sn, the thermal conductivity of PA6/Sn was nearly constant because of the serious agglomeration of Sn. However, when 20 wt% (5.4 vol% of Sn was added into PA6 containing 50 wt% (33.3 vol% of graphite, the thermal conductivity of the composite was dramatically increased to 5.364 versus 1.852 W·(m·K–1 for the PA6/graphite composite, which suggests that the incorporation of graphite and Sn have a significant synergistic effect on the thermal conductivity improvement of PA6. What is more, the electrical conductivity of the composite increased nearly 8 orders of magnitudes after introducing both graphite and Sn. Characterization of microstructure and energy dispersive spectrum analysis (EDS indicates that the dispersion of Sn in PA6/graphite/Sn was much more uniform than that of PA6/Sn composite. According to Differential Scanning Calorimetry measurement and EDS, the uniform dispersion of Sn in PA6/graphite/Sn and the high thermal conductivity of PA6/graphite/Sn are speculated to be related with the electron transfer between graphite and Sn, which makes Sn distribute evenly around the graphite layers.

  9. Simulating the growth process of aromatic polyamide layer by monomer concentration controlling method

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Yan [Vontron Technology Co., Ltd., Guiyang 550018, Guizhou (China); Liang, Songmiao, E-mail: liangsongmiao@vontron.com.cn [Vontron Technology Co., Ltd., Guiyang 550018, Guizhou (China); Wu, Zongce; Cai, Zhiqi [Vontron Technology Co., Ltd., Guiyang 550018, Guizhou (China); Zhao, Ning [National Laboratory of Molecular Sciences, Institute of Chemistry, Chinese Academy of Sciences (ICCAS), Beijing 100190 (China)

    2014-09-30

    Highlights: • A concentration controlling method to simulate the growth process of polyamide layer was developed. • The surface structure features and properties of polyamide layer at its different growth stages were systematically investigated. • Structure transition from spherical aggregator to leaf-like to typical ridge-and-valley was observed. • The performance of RO membrane is closely related to the structure of polyamide. - Abstract: With the wide distribution and gradual increase of TMC concentration (C{sub TMC}) from 1 × 10{sup −4} wt% to 2.5 × 10{sup −1} wt%, the main purpose of this work is to simulate the surface structure and properties of polyamide layer of reverse osmosis membranes at its different growth stage. The surface structure and properties of the resulted membranes were then characterized by atomic force microscopy (AFM), scanning electron microscope (SEM), attenuated total reflectance infrared (ATR-IR) spectroscopy, drop shape analysis system and electrokinetic analyzer. The structure growth of polyamide layer underwent in turn three different stages including spherical aggregator, leaf-like and typical ridge-valley structure. Spherical aggregator is the intrinsic structure in the inner layer of polyamide while leaf-like structure is transitional on the outmost polyamide layer. Furthermore, to clarify the effect of the structure change on the properties of polyamide layer, contact angle and zeta potential in the surface of polyamide layer were studied. Hydrophilic surface of polyamide layer is accessible at higher TMC concentration because of the presence of negative charged groups. Performances of the membranes were further measured with an emphasis on studying its structure–performance relationship during the growth process of polyamide layer.

  10. Rain scavenging of radioactive particles

    International Nuclear Information System (INIS)

    Williams, A.L.

    1975-01-01

    An assessment is made of the rainout of airborne radioactive particles from a nuclear detonation with emphasis on the microphysical removal processes. For submicron particles the scavenging processes examined are Brownian and turbulent diffusion to cloud droplets. For particles larger than 1 μm radius, nucleation scavenging is examined. For various particle size and radioactivity distributions, it is found that from 27 to 99 percent of the radioactivity is attached to cloud droplets and subject to rapid removal by rain. (U.S.)

  11. Precipitation scavenging of aerosol particles

    International Nuclear Information System (INIS)

    Radke, L.F.; Eltgroth, M.W.; Hobbs, P.V.

    1978-01-01

    The paper presents the results of precipitation scavenging measurements of particles in the atmosphere and in plumes which were obtained using an airborne measuring system. Attention is given to the so-called 'Greenfield gap' and collection efficiencies for submicron particles

  12. Trophic facilitation or limitation? Comparative effects of pumas and black bears on the scavenger community.

    Science.gov (United States)

    Allen, Maximilian L; Elbroch, L Mark; Wilmers, Christopher C; Wittmer, Heiko U

    2014-01-01

    Scavenging is a widespread behaviour and an important process influencing food webs and ecological communities. Large carnivores facilitate the movement of energy across trophic levels through the scavenging and decomposition of their killed prey, but competition with large carnivores is also likely to constrain acquisition of carrion by scavengers. We used an experimental approach based on motion-triggered video cameras at black-tailed deer (Odocoileus hemionus columbianus) carcasses to measure the comparative influences of two large carnivores in the facilitation and limitation of carrion acquisition by scavengers. We found that pumas (Puma concolor) and black bears (Ursus americanus) had different effects on their ecological communities. Pumas, as a top-level predator, facilitated the consumption of carrion by scavengers, despite significantly reducing their observed sum feeding times (165.7 min ± 21.2 SE at puma kills 264.3 min ± 30.1 SE at control carcasses). In contrast, black bears, as the dominant scavenger in the system, limited consumption of carrion by scavengers as evidenced by the observed reduction of scavenger species richness recorded at carcasses where they were present (mean = 2.33 ± 0.28 SE), compared to where they were absent (mean = 3.28 ± 0.23 SE). Black bears also had large negative effects on scavenger sum feeding times (88.5 min ± 19.8 SE at carcasses where bears were present, 372.3 min ± 50.0 SE at carcasses where bears were absent). In addition, we found that pumas and black bears both increased the nestedness (a higher level of order among species present) of the scavenger community. Our results suggest that scavengers have species-specific adaptions to exploit carrion despite large carnivores, and that large carnivores influence the structure and composition of scavenger communities. The interactions between large carnivores and scavengers should be considered in future studies of food webs and ecological communities.

  13. Trophic facilitation or limitation? Comparative effects of pumas and black bears on the scavenger community.

    Directory of Open Access Journals (Sweden)

    Maximilian L Allen

    Full Text Available Scavenging is a widespread behaviour and an important process influencing food webs and ecological communities. Large carnivores facilitate the movement of energy across trophic levels through the scavenging and decomposition of their killed prey, but competition with large carnivores is also likely to constrain acquisition of carrion by scavengers. We used an experimental approach based on motion-triggered video cameras at black-tailed deer (Odocoileus hemionus columbianus carcasses to measure the comparative influences of two large carnivores in the facilitation and limitation of carrion acquisition by scavengers. We found that pumas (Puma concolor and black bears (Ursus americanus had different effects on their ecological communities. Pumas, as a top-level predator, facilitated the consumption of carrion by scavengers, despite significantly reducing their observed sum feeding times (165.7 min ± 21.2 SE at puma kills 264.3 min ± 30.1 SE at control carcasses. In contrast, black bears, as the dominant scavenger in the system, limited consumption of carrion by scavengers as evidenced by the observed reduction of scavenger species richness recorded at carcasses where they were present (mean = 2.33 ± 0.28 SE, compared to where they were absent (mean = 3.28 ± 0.23 SE. Black bears also had large negative effects on scavenger sum feeding times (88.5 min ± 19.8 SE at carcasses where bears were present, 372.3 min ± 50.0 SE at carcasses where bears were absent. In addition, we found that pumas and black bears both increased the nestedness (a higher level of order among species present of the scavenger community. Our results suggest that scavengers have species-specific adaptions to exploit carrion despite large carnivores, and that large carnivores influence the structure and composition of scavenger communities. The interactions between large carnivores and scavengers should be considered in future studies of food webs and ecological communities.

  14. Polyamide membranes with nanoscale Turing structures for water purification

    Science.gov (United States)

    Tan, Zhe; Chen, Shengfu; Peng, Xinsheng; Zhang, Lin; Gao, Congjie

    2018-05-01

    The emergence of Turing structures is of fundamental importance, and designing these structures and developing their applications have practical effects in chemistry and biology. We use a facile route based on interfacial polymerization to generate Turing-type polyamide membranes for water purification. Manipulation of shapes by control of reaction conditions enabled the creation of membranes with bubble or tube structures. These membranes exhibit excellent water-salt separation performance that surpasses the upper-bound line of traditional desalination membranes. Furthermore, we show the existence of high water permeability sites in the Turing structures, where water transport through the membranes is enhanced.

  15. Morphology study of polyamide 6/bentonite clay nanocomposites

    International Nuclear Information System (INIS)

    Paz, Rene A.; Araujo, Edcleide M.; Melo, Tomas J.A.; Leite, Amanda M.D.; Medeiros, Vanessa Nobrega; Pessan, Luiz A.; Passador, Fabio R.

    2011-01-01

    Polymer/clay nanocomposites have had much attention in recent years, especially those developed with layered silicates, due to the need for engineering materials more efficient than pure polymers for certain applications. The level of exfoliation of layered silicates in the crystalline structure of polymer matrices has been studied and it has been observed that it affects the behavior of crystalline and therefore the mechanical and physical properties. In this study, polyamide 6 nanocomposites were obtained by the melt intercalation technique, using regional bentonite clay modified with a quaternary ammonium salt in an amount of 3% by weight. XRD and TEM tests showed obtaining nanocomposites with exfoliated structures (author)

  16. Grafting of acrylamide onto synthetic co polyamide by gamma irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Hamoud, M R; Qamhieyh, E A [Chemistry Dept., College of Ibn Al-Haitham Baghdad university-Adhamiyah-Baghdad- (Iraq)

    1995-10-01

    Grafted copolymer was prepared by using gamma irradiation to graft acrylamide onto polymeric molecule prepared by interfacial condensation between two diamine molecules like 1,2 diamino propane and 1,6 diamino-hexane in aqueous layer with sebacoyl chloride in organic layer. The resulted co polyamide was grafted with acrylamide using gamma irradiation. The optimum conditions of grafting reaction were found, also various factors such as the effect of solvents, redox systems and the role water on the radiochemical grafting were studied. Many techniques were used in the characterization of the copolymer before and after grafting. 8 figs.,.

  17. A Polyamide Inhibits Replication of Vesicular Stomatitis Virus by Targeting RNA in the Nucleocapsid

    Energy Technology Data Exchange (ETDEWEB)

    Gumpper, Ryan H.; Li, Weike; Castañeda, Carlos H.; Scuderi, M. José; Bashkin, James K.; Luo, Ming; Dutch, Rebecca Ellis

    2018-02-07

    Polyamides have been shown to bind double-stranded DNA by complementing the curvature of the minor groove and forming various hydrogen bonds with DNA. Several polyamide molecules have been found to have potent antiviral activities against papillomavirus, a double-stranded DNA virus. By analogy, we reason that polyamides may also interact with the structured RNA bound in the nucleocapsid of a negative-strand RNA virus. Vesicular stomatitis virus (VSV) was selected as a prototype virus to test this possibility since its genomic RNA encapsidated in the nucleocapsid forms a structure resembling one strand of an A-form RNA duplex. One polyamide molecule, UMSL1011, was found to inhibit infection of VSV. To confirm that the polyamide targeted the nucleocapsid, a nucleocapsid-like particle (NLP) was incubated with UMSL1011. The encapsidated RNA in the polyamide-treated NLP was protected from thermo-release and digestion by RNase A. UMSL1011 also inhibits viral RNA synthesis in the intracellular activity assay for the viral RNA-dependent RNA polymerase. The crystal structure revealed that UMSL1011 binds the structured RNA in the nucleocapsid. The conclusion of our studies is that the RNA in the nucleocapsid is a viable antiviral target of polyamides. Since the RNA structure in the nucleocapsid is similar in all negative-strand RNA viruses, polyamides may be optimized to target the specific RNA genome of a negative-strand RNA virus, such as respiratory syncytial virus and Ebola virus.

    IMPORTANCENegative-strand RNA viruses (NSVs) include several life-threatening pathogens, such as rabies virus, respiratory syncytial virus, and Ebola virus. There are no effective antiviral drugs against these viruses. Polyamides offer an exceptional opportunity because they may be optimized to target each NSV. Our studies on vesicular stomatitis virus, an NSV, demonstrated that a polyamide molecule could specifically target the viral RNA in the nucleocapsid and inhibit

  18. 21 CFR 868.5590 - Scavenging mask.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Scavenging mask. 868.5590 Section 868.5590 Food... DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5590 Scavenging mask. (a) Identification. A scavenging mask is a device positioned over a patient's nose to deliver anesthetic or analgesic gases to the...

  19. Scavenging in the genus Natrix

    Directory of Open Access Journals (Sweden)

    Cesar Ayres

    2012-07-01

    Full Text Available Scavenging is reported as an unusual behaviour of snakes. However, it is likely more common than is supposed. Here I report the use of dead newts as prey source by water snakes of the genus Natrix at a dam in north-western Spain. Juveniles and adults viperine snakes (Natrix maura, and also an adult grass snake (Natrix natrix were found feeding on newt carcasses.

  20. Electron beam radiation effects on recycled polyamide-6

    International Nuclear Information System (INIS)

    Evora, Maria Cecilia; Silva, Leonardo G. de Andrade e

    2001-01-01

    Applications of electron beam processing in the treatment of polymers are commonly used. The interaction of high energy radiation with polymers may cause permanent modifications in the polymer's physicochemical structure. The induced modifications may result in degradation of the polymer or in improvement of its properties (crosslinking), which are simultaneous and competing processes, depending on the radiation dose utilized. Crosslinking occurs more readily in the polymer's amorphous content and this process makes the glass transition temperature (Tg) of the polymers to increase. Successive recycling cycles promote changes in polymers properties, such as breaking of structure, molecular weight reduction, melt index increase and mechanical resistance reduction. The polyamide-6 resin was recycled for three successive recycling cycles and thi polyamide-6 specimens were molded by the process of injection molding. These specimens were irradiated at the Nuclear Energetic Research Institute (IPEN) radiation facility, on a JOB 188 model accelerator, with a 1.5 MeV electron beam, doses of 200, 300, 400, 500 and 600 kGy, and dose rate of 22.61 kGy/s. The DMA tests were performed using DMA-983 equipment from TA Instruments and two heatings were adopted in order to eliminate the moisture absorption. The X-ray diffraction analysis wa carried out at the Philips PW 1830 model equipment

  1. Thin Film Polyamide Membranes with Photoresponsive Antibacterial Activity

    KAUST Repository

    Duong, Phuoc H. H.

    2017-08-09

    Membranes containing a photosensitizer molecule as part of the selective layer are proposed with demonstrated anti-biofouling activity. For the membrane preparation, mixtures of an amine-functionalized photosensitizer molecule, (5,10,15,20-(tetra-4-aminophenyl)porphyrin) and m-phenylene diamine (MPD) reacted with trimesoyl chloride (TMC) by interfacial polymerization to form thin polyamide films on top of an asymmetric porous support. A highly permeable membrane (35.4 Lm−2h−1bar−1) with 99 % rejection of Brilliant Blue R (826 g/mol) was obtained using 0.25 wt% porphyrin and 0.75 wt% MPD as amine monomers. Under visible light exposure, singlet oxygen (1O2) is generated in the porphyrin containing-polyamide film, reaching the bacteria in the feed by diffusion and enhancing the biofouling resistance and anti-microbial activity. Anti-biofouling and anti-microbial photoactivity in solution are demonstrated on Staphylococcus aureus at different porphyrin concentrations and light exposure time.

  2. Thin Film Polyamide Membranes with Photoresponsive Antibacterial Activity

    KAUST Repository

    Duong, Phuoc H. H.; Hong, Pei-Ying; Musteata, Valentina-Elena; Peinemann, Klaus-Viktor; Nunes, Suzana Pereira

    2017-01-01

    Membranes containing a photosensitizer molecule as part of the selective layer are proposed with demonstrated anti-biofouling activity. For the membrane preparation, mixtures of an amine-functionalized photosensitizer molecule, (5,10,15,20-(tetra-4-aminophenyl)porphyrin) and m-phenylene diamine (MPD) reacted with trimesoyl chloride (TMC) by interfacial polymerization to form thin polyamide films on top of an asymmetric porous support. A highly permeable membrane (35.4 Lm−2h−1bar−1) with 99 % rejection of Brilliant Blue R (826 g/mol) was obtained using 0.25 wt% porphyrin and 0.75 wt% MPD as amine monomers. Under visible light exposure, singlet oxygen (1O2) is generated in the porphyrin containing-polyamide film, reaching the bacteria in the feed by diffusion and enhancing the biofouling resistance and anti-microbial activity. Anti-biofouling and anti-microbial photoactivity in solution are demonstrated on Staphylococcus aureus at different porphyrin concentrations and light exposure time.

  3. Characterization of isolated polyamide thin films of RO and NF membranes using novel TEM techniques

    KAUST Repository

    Pacheco, Federico A.; Pinnau, Ingo; Reinhard, Martin; Leckie, James O.

    2010-01-01

    Achieving a better understanding of transport and rejection mechanisms in RO and NF membranes requires more detailed information of the nanostructure of polyamide thin films. This study reports on two novel transmission electron microscopy (TEM) techniques for characterizing polyamide nanostructure. The first technique produces cross-sectional images of isolated polyamide thin films by removing the polysulfone support from regular TEM cross-sections. In the second technique called " projected area" TEM (PA-TEM), isolated polyamide thin films are placed with their surface perpendicular to the electron beam. The resulting images capture the thickness, morphology and mass density of the entire thin film. In combination, these new techniques provide information on polyamide nanostructure that is not evident using conventional methods. For the commercial RO membrane ESPA3, the cross-sectional view of the isolated polyamide thin film shows a 30-60. nm thick base of nodular polyamide (presumably the separation barrier) that forms a relatively smooth interface with the polysulfone support. Above this, a more open structure of loose polyamide extends outward giving rise to the ridge-and-valley surface structure. In PA-TEM images, the ridges and valleys correspond to the dark and bright regions, respectively; the polyamide nodular base appears as round features forming an irregular honeycomb pattern throughout the images. Membrane cross-sections were prepared with a simple resin embedding protocol using the acrylic resin LR White. The protocol did not require dehydration steps, and was applicable to both dry and wet membrane samples. Artifacts that may be produced during sample preparation were also documented. © 2010 Elsevier B.V.

  4. Characterization of isolated polyamide thin films of RO and NF membranes using novel TEM techniques

    KAUST Repository

    Pacheco, Federico A.

    2010-08-15

    Achieving a better understanding of transport and rejection mechanisms in RO and NF membranes requires more detailed information of the nanostructure of polyamide thin films. This study reports on two novel transmission electron microscopy (TEM) techniques for characterizing polyamide nanostructure. The first technique produces cross-sectional images of isolated polyamide thin films by removing the polysulfone support from regular TEM cross-sections. In the second technique called " projected area" TEM (PA-TEM), isolated polyamide thin films are placed with their surface perpendicular to the electron beam. The resulting images capture the thickness, morphology and mass density of the entire thin film. In combination, these new techniques provide information on polyamide nanostructure that is not evident using conventional methods. For the commercial RO membrane ESPA3, the cross-sectional view of the isolated polyamide thin film shows a 30-60. nm thick base of nodular polyamide (presumably the separation barrier) that forms a relatively smooth interface with the polysulfone support. Above this, a more open structure of loose polyamide extends outward giving rise to the ridge-and-valley surface structure. In PA-TEM images, the ridges and valleys correspond to the dark and bright regions, respectively; the polyamide nodular base appears as round features forming an irregular honeycomb pattern throughout the images. Membrane cross-sections were prepared with a simple resin embedding protocol using the acrylic resin LR White. The protocol did not require dehydration steps, and was applicable to both dry and wet membrane samples. Artifacts that may be produced during sample preparation were also documented. © 2010 Elsevier B.V.

  5. Synthesis of nanosilver on polyamide fabric using silver/ammonia complex

    Energy Technology Data Exchange (ETDEWEB)

    Montazer, Majid, E-mail: tex5mm@aut.ac.ir [Textile Department, Functional Fibrous Structures and Environmental Enhancement (FFSEE), Amirkabir University of Technology, Hafez Avenue, Tehran (Iran, Islamic Republic of); Shamei, Ali; Alimohammadi, Farbod [Young Researchers Club, Tehran South Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of)

    2014-05-01

    In this paper, a novel synthesis method for nanosilver has been introduced on or within the polymeric chains of polyamide 6 fabric by using silver/ammonia complex [Ag(NH{sub 3}){sub 2}]{sup +}. The silver complex was reduced directly by functional groups of polyamide chains without using any additional chemical reducing agents. The polyamide fabric was also stabilized with formation of new linkages between the polymeric chains of the nylon fabric through silver nanoparticle synthesis. The presence of nanosilver on the fabric was confirmed by UV–vis spectra, EDX patterns and XRD patterns. In addition, X-ray photoelectron spectroscopy (XPS) was utilized to identify the chemical state of silver in a range of silver oxide and silver metal. The SEM images confirmed the presence of nanosilver on the polyamide within the size of 20 and 150 nm. Excellent antibacterial properties were achieved with the treated fabrics against Staphylococcus aureus and Escherichia coli. Further, the antibacterial properties of the polyamide fabric treated with 35 mg/L silver/ammonia were durable against washing as they only decreased to 98.6% after 20 washes. In addition, some other properties of the treated fabrics including color changes, dimensional stability, water droplet adsorption, and reflectance spectrum are reported and thoroughly discussed. - Highlights: • Novel in situ synthesis of nanosilver on polyamide 6 • Synthesis of nanosilver without using external stabilizing and reducing agent • Synthesis of nanosilver particles within molecular chains of polyamide 6 • Producing antibacterial polyamide 6 using 35 mg/L Ag/ammonia complex • Obtaining durable antibacterial properties on polyamide 6 by this method.

  6. Synthesis of nanosilver on polyamide fabric using silver/ammonia complex

    International Nuclear Information System (INIS)

    Montazer, Majid; Shamei, Ali; Alimohammadi, Farbod

    2014-01-01

    In this paper, a novel synthesis method for nanosilver has been introduced on or within the polymeric chains of polyamide 6 fabric by using silver/ammonia complex [Ag(NH 3 ) 2 ] + . The silver complex was reduced directly by functional groups of polyamide chains without using any additional chemical reducing agents. The polyamide fabric was also stabilized with formation of new linkages between the polymeric chains of the nylon fabric through silver nanoparticle synthesis. The presence of nanosilver on the fabric was confirmed by UV–vis spectra, EDX patterns and XRD patterns. In addition, X-ray photoelectron spectroscopy (XPS) was utilized to identify the chemical state of silver in a range of silver oxide and silver metal. The SEM images confirmed the presence of nanosilver on the polyamide within the size of 20 and 150 nm. Excellent antibacterial properties were achieved with the treated fabrics against Staphylococcus aureus and Escherichia coli. Further, the antibacterial properties of the polyamide fabric treated with 35 mg/L silver/ammonia were durable against washing as they only decreased to 98.6% after 20 washes. In addition, some other properties of the treated fabrics including color changes, dimensional stability, water droplet adsorption, and reflectance spectrum are reported and thoroughly discussed. - Highlights: • Novel in situ synthesis of nanosilver on polyamide 6 • Synthesis of nanosilver without using external stabilizing and reducing agent • Synthesis of nanosilver particles within molecular chains of polyamide 6 • Producing antibacterial polyamide 6 using 35 mg/L Ag/ammonia complex • Obtaining durable antibacterial properties on polyamide 6 by this method

  7. CRYSTALLIZATION KINETICS OF POLYMERIC NANOCOMPOSITES BASED ON POLYAMIDE 12 MODIFIED BY Cr2O3 NANOPARTICLES

    Directory of Open Access Journals (Sweden)

    E. S. Shapoval

    2014-09-01

    Full Text Available In situ polymerization method is used for obtaining polymeric composites based on polyamide12 matrix (PA 12, filled with Cr2O3 nanoparticles. The carried out researches result in synthesis method development for polymeric nanocomposites based on PA 12 matrix filled with nano-sized Cr2O3magnetic particles providing uniform embedding of the filler into polymeric matrix without formation of nanoparticles agglomerates. Mechanical tests on samples compression are carried out. It is shown that mechanical properties of polymeric composites (Young’s modulus, durability limit are decreased for 20-30 % as compared with not modified PA 12 synthesized by means of the chosen method. The influence of the filler on crystallization morphology and kinetics of polymeric nanocomposites is determined by electron microscopy and differential scanning calorimetry. The values of crystallization degree, crystallization rate constant for different supercooling intervals and parameters of Avrami equation are obtained. The initial nucleation is shown to be going on according to non-thermal mechanism, and nanoparticles are not the germs of crystallization. It is stated that nanoparticles are embedded into polymeric matrix and uniformly allocated in crystallites. Research results can find their application at creation of electric and magnetic fields, micro-sized mechanical devices, and at development of new materials for 3D printers.

  8. Highly Hydrophilic Thin-Film Composite Forward Osmosis Membranes Functionalized with Surface-Tailored Nanoparticles

    KAUST Repository

    Tiraferri, Alberto; Kang, Yan; Giannelis, Emmanuel P.; Elimelech, Menachem

    2012-01-01

    Thin-film composite polyamide membranes are state-of-the-art materials for membrane-based water purification and desalination processes, which require both high rejection of contaminants and high water permeabilities. However, these membranes

  9. Relating performance of thin-film composite forward osmosis membranes to support layer formation and structure

    KAUST Repository

    Tiraferri, Alberto; Yip, Ngai Yin; Phillip, William A.; Schiffman, Jessica D.; Elimelech, Menachem

    2011-01-01

    the technology to the point that it is commercially viable. Here, a systematic investigation of the influence of thin-film composite membrane support layer structure on forward osmosis performance is conducted. The membranes consist of a selective polyamide

  10. To scavenge or not to scavenge: that is the question

    Energy Technology Data Exchange (ETDEWEB)

    Nowak, Elzbieta; Brzuszkiewicz, Anna [Synchrotron Radiation Research Section, MCL, National Cancer Institute, Argonne National Laboratory, Argonne, IL 60439 (United States); Dauter, Miroslawa [SAIC-Frederick Inc., Basic Research Program, Argonne National Laboratory, Argonne, IL 60439 (United States); Dauter, Zbigniew, E-mail: dauter@anl.gov [Synchrotron Radiation Research Section, MCL, National Cancer Institute, Argonne National Laboratory, Argonne, IL 60439 (United States); Rosenbaum, Gerd, E-mail: dauter@anl.gov [Department of Biochemistry, University of Georgia, SER-CAT at the APS, Argonne, IL 60439 (United States); Synchrotron Radiation Research Section, MCL, National Cancer Institute, Argonne National Laboratory, Argonne, IL 60439 (United States)

    2009-09-01

    Analysis of a series of diffraction data sets measured from several native as well as nicotinic acid-soaked crystals of trypsin suggests that this potential scavenger does not have any statistically significant effect on the amount of radiation damage incurred in the crystals on X-ray irradiation at 100 K. Analysis of a series of diffraction data sets measured from four native as well as four nicotinic acid-soaked crystals of trypsin at 100 K shows a high variability in radiation-sensitivity among individual crystals for both nicotinic acid-soaked and native crystals. The level of radiation-sensitivity and the extent of its variability is statistically indistinguishable between the two conditions. This suggests that this potential scavenger does not have any statistically significant effect on the amount of radiation damage incurred in the crystals on X-ray irradiation. This is in contrast to previous results [Kauffmann et al. (2006 ▶), Structure, 14, 1099–1105] where only one crystal specimen was used for each condition (native and nicotinic acid-soaked)

  11. Hemoglobin and heme scavenger receptors

    DEFF Research Database (Denmark)

    Nielsen, Marianne Jensby; Møller, Holger Jon; Moestrup, Søren Kragh

    2010-01-01

    Heme, the functional group of hemoglobin, myoglobin, and other hemoproteins, is a highly toxic substance when it appears in the extracellular milieu. To circumvent potential harmful effects of heme from hemoproteins released during physiological or pathological cell damage (such as hemolysis...... and rhabdomyolysis), specific high capacity scavenging systems have evolved in the mammalian organism. Two major systems, which essentially function in a similar way by means of a circulating latent plasma carrier protein that upon ligand binding is recognized by a receptor, are represented by a) the hemoglobin...

  12. Ultrathin Polyamide Membranes Fabricated from Free-Standing Interfacial Polymerization: Synthesis, Modifications, and Post-treatment

    KAUST Repository

    Cui, Yue; Liu, Xiang-Yang; Chung, Neal Tai-Shung

    2016-01-01

    ) membranes. The polyamide selective layer usually possesses a high selectivity and permeability, making it the heart of this membrane technology. To further improve and understand its formation, with entirely excluding the effect of substrate, an ultrathin

  13. Free volume sizes in intercalated polyamide 6/clay nanocomposites

    DEFF Research Database (Denmark)

    Wiinberg, P.; Eldrup, Morten Mostgaard; Pedersen, N.J.

    2005-01-01

    The effect of incorporating modified clay into a polyamide 6 (PA6) matrix, on the free volume cavity sizes and the thermal and viscoelastic properties of the resulting nanocomposite, was studied with positron annihilation lifetime spectroscopy, differential scanning calorimetry and dynamic...... response of PA6/clay nanocomposites, as compared to unfilled PA6, pointed towards a changed mobility in the non-crystalline regions. At high concentrations of clay (> 19 wt%) an increase of the free volume cavity diameter was observed, indicating a lower chain packing efficiency in the PA6/clay...... nanocomposites. The increased free volume sizes were present both above and below the glass transition temperature of PA6. (c) 2005 Elsevier Ltd. All rights reserved....

  14. Stiffening mechanisms in amorphous polyamide bio-nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Focke, Walter W. [Institute of Applied Materials, Department of Chemical Engineering, University of Pretoria, Private Bag X20, Hatfield 0028, Pretoria (South Africa); Macheca, Afonso D. [Institute of Applied Materials, Department of Chemical Engineering, University of Pretoria, Private Bag X20, Hatfield 0028, Pretoria (South Africa); Department of Chemical Engineering, Eduardo Mondlane University, P.O. Box 257, Maputo (Mozambique); Benhamida, Aida; Kaci, Mustapha [Laboratoire des Matériaux Polymères Avancés (LMPA), Université de Bejaia 06000 (Algeria)

    2016-05-18

    Dimer fatty acid polyamide nanocomposites based on flake- or needle-shaped nanoparticles were prepared via melt compounding. Transmission electron microscopy showed the presence of both individually dispersed particles and particle agglomerates in the polymer matrix. Dynamic mechanical analysis suggests that three stiffening mechanisms were operating. The reinforcing effect of the high stiffness inorganic filler particles is the primary contributor. Together with the chain confinement effect, that expresses itself in an apparent increase in the glass transition temperature, this provided an adequate rationalization of the stiffness variation below Tg. However, an additional stiffening effect is indicated at temperatures above Tg. The mechanism may involve dynamic network formation based on fluctuating hydrogen bonding interactions between the polymer chains and the filler particles.

  15. Processing and Mechanical Properties of Macro Polyamide Fiber Reinforced Concrete.

    Science.gov (United States)

    Jeon, Joong Kyu; Kim, WooSeok; Jeon, Chan Ki; Kim, Jin Cheol

    2014-11-26

    This study developed a macro-sized polyamide (PA) fiber for concrete reinforcement and investigated the influence of the PA fiber on flexural responses in accordance with ASTM standards. PA fibers are advantageous compared to steel fibers that are corrosive and gravitated. The macro-sized PA fiber significantly improved concrete ductility and toughness. Unlike steel fibers, the PA fibers produced two peak bending strengths. The first-peaks occurred near 0.005 mm of deflection and decreased up to 0.5 mm of deflection. Then the bending strength increased up to second-peaks until the deflections reached between 1.0 and 1.5 mm. The averaged flexural responses revealed that PA fiber content did not significantly influence flexural responses before L /600, but had significant influence thereafter. Toughness performance levels were also determined, and the results indicated more than Level II at L /600 and Level IV at others.

  16. Strain rate dependency of laser sintered polyamide 12

    Directory of Open Access Journals (Sweden)

    Cook J.E.T.

    2015-01-01

    Full Text Available Parts processed by Additive Manufacturing can now be found across a wide range of applications, such as those in the aerospace and automotive industry in which the mechanical response must be optimised. Many of these applications are subjected to high rate or impact loading, yet it is believed that there is no prior research on the strain rate dependence in these materials. This research investigates the effect of strain rate and laser energy density on laser sintered polyamide 12. In the study presented here, parts produced using four different laser sintered energy densities were exposed to uniaxial compression tests at strain rates ranging from 10−3 to 10+3 s−1 at room temperature, and the dependence on these parameters is presented.

  17. 3D visualization of the internal nanostructure of polyamide thin films in RO membranes

    KAUST Repository

    Pacheco Oreamuno, Federico

    2015-11-02

    The front and back surfaces of fully aromatic polyamide thin films isolated from reverse osmosis (RO) membranes were characterized by TEM, SEM and AFM. The front surfaces were relatively rough showing polyamide protuberances of different sizes and shapes; the back surfaces were all consistently smoother with very similar granular textures formed by polyamide nodules of 20–50 nm. Occasional pore openings of approximately the same size as the nodules were observed on the back surfaces. Because traditional microscopic imaging techniques provide limited information about the internal morphology of the thin films, TEM tomography was used to create detailed 3D visualizations that allowed the examination of any section of the thin film volume. These tomograms confirmed the existence of numerous voids within the thin films and revealed structural characteristics that support the water permeance difference between brackish water (BWRO) and seawater (SWRO) RO membranes. Consistent with a higher water permeance, the thin film of the BWRO membrane ESPA3 contained relatively more voids and thinner sections of polyamide than the SWRO membrane SWC3. According to the tomograms, most voids originate near the back surface and many extend all the way to the front surface shaping the polyamide protuberances. Although it is possible for the internal voids to be connected to the outside through the pore openings on the back surface, it was verified that some of these voids comprise nanobubbles that are completely encapsulated by polyamide. TEM tomography is a powerful technique for investigating the internal nanostructure of polyamide thin films. A comprehensive knowledge of the nanostructural distribution of voids and polyamide sections within the thin film may lead to a better understanding of mass transport and rejection mechanisms in RO membranes.

  18. 3D visualization of the internal nanostructure of polyamide thin films in RO membranes

    KAUST Repository

    Pacheco Oreamuno, Federico; Sougrat, Rachid; Reinhard, Martin; Leckie, James O.; Pinnau, Ingo

    2015-01-01

    The front and back surfaces of fully aromatic polyamide thin films isolated from reverse osmosis (RO) membranes were characterized by TEM, SEM and AFM. The front surfaces were relatively rough showing polyamide protuberances of different sizes and shapes; the back surfaces were all consistently smoother with very similar granular textures formed by polyamide nodules of 20–50 nm. Occasional pore openings of approximately the same size as the nodules were observed on the back surfaces. Because traditional microscopic imaging techniques provide limited information about the internal morphology of the thin films, TEM tomography was used to create detailed 3D visualizations that allowed the examination of any section of the thin film volume. These tomograms confirmed the existence of numerous voids within the thin films and revealed structural characteristics that support the water permeance difference between brackish water (BWRO) and seawater (SWRO) RO membranes. Consistent with a higher water permeance, the thin film of the BWRO membrane ESPA3 contained relatively more voids and thinner sections of polyamide than the SWRO membrane SWC3. According to the tomograms, most voids originate near the back surface and many extend all the way to the front surface shaping the polyamide protuberances. Although it is possible for the internal voids to be connected to the outside through the pore openings on the back surface, it was verified that some of these voids comprise nanobubbles that are completely encapsulated by polyamide. TEM tomography is a powerful technique for investigating the internal nanostructure of polyamide thin films. A comprehensive knowledge of the nanostructural distribution of voids and polyamide sections within the thin film may lead to a better understanding of mass transport and rejection mechanisms in RO membranes.

  19. Scavenging and recombination kinetics in radiation chemistry.

    Science.gov (United States)

    Al-Samra, Eyad H; Green, Nicholas J B

    2017-08-02

    This work describes stochastic models developed to study the competition between radical scavenging and recombination for simple model systems typical of radiation chemistry, where the reactive particles are tightly clustered and reactions are assumed fully diffusion limited. Three models are developed: a Monte Carlo random flights model with a periodic boundary condition for scavengers, Monte Carlo simulations in which the scavenging rate is calculated from the Smoluchowski theory for diffusion-limited reactions and a modification of the independent reaction times method where the scavengers close to the spur are explicitly included and the scavengers further away are treated as a continuum. The results indicate that the Smoluchowski theory makes a systematic overestimate of the scavenging rate when such competition is present. A correction for the Smoluchowski rate constant is suggested, an analytical justification is presented and it is tested against the simulations, and shown to be a substantial improvement.

  20. Sequence-specific DNA alkylation by tandem Py-Im polyamide conjugates.

    Science.gov (United States)

    Taylor, Rhys Dylan; Kawamoto, Yusuke; Hashiya, Kaori; Bando, Toshikazu; Sugiyama, Hiroshi

    2014-09-01

    Tandem N-methylpyrrole-N-methylimidazole (Py-Im) polyamides with good sequence-specific DNA-alkylating activities have been designed and synthesized. Three alkylating tandem Py-Im polyamides with different linkers, which each contained the same moiety for the recognition of a 10 bp DNA sequence, were evaluated for their reactivity and selectivity by DNA alkylation, using high-resolution denaturing gel electrophoresis. All three conjugates displayed high reactivities for the target sequence. In particular, polyamide 1, which contained a β-alanine linker, displayed the most-selective sequence-specific alkylation towards the target 10 bp DNA sequence. The tandem Py-Im polyamide conjugates displayed greater sequence-specific DNA alkylation than conventional hairpin Py-Im polyamide conjugates (4 and 5). For further research, the design of tandem Py-Im polyamide conjugates could play an important role in targeting specific gene sequences. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Formation of high aspect ratio polyamide-6 nanofibers via electrically induced double layer during electrospinning

    International Nuclear Information System (INIS)

    Nirmala, R.; Nam, Ki Taek; Park, Soo-Jin; Shin, Yu-Shik; Navamathavan, R.; Kim, Hak Yong

    2010-01-01

    In the present study, the formation of high aspect ratio nanofibers in polyamide-6 was investigated as a function of applied voltage ranging from 15 to 25 kV using electrospinning technique. All other experimental parameters were kept constant. The electrospun polyamide-6 nanofibers were characterized by field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and matrix-assisted laser desorption ionization time-of-flight (MALDI-TOF). FE-SEM images of polyamide-6 nanofibers showed that the diameter of the electrospun fiber was decreased with increasing applied voltage. At the critical applied voltage, the polymer solution was completely ionized to form the dense high aspect ratio nanofibers in between the main nanofibers. The diameter of the polyamide-6 nanofibers was observed to be in the range of 75-110 nm, whereas the high aspect ratio structures consisted of regularly distributed very fine nanofibers with diameters of about 9-28 nm. Trends in fiber diameter and diameter distribution were discussed for the high aspect ratio nanofibers. TEM results revealed that the formation of double layers in polyamide-6 nanofibers and then split-up into ultrafine fibers. The electrically induced double layer in combination with the polyelectrolytic nature of solution is proposed as the suitable mechanisms for the formation of high aspect ratio nanofibers in polyamide-6.

  2. Synthesis and characterizations of Pt nanorods on electrospun polyamide-6 nanofibers templates

    International Nuclear Information System (INIS)

    Nirmala, R.; Navamathavan, R.; Won, Jeong Jin; Jeon, Kyung Soo; Yousef, Ayman; Kim, Hak Yong

    2012-01-01

    Highlights: ► Electrospun polyamide-6 nanofibers were used as the templates for synthesis Pt nanorods. ► Polyamide-6 nanofibers surfaces were plasma treated to coat Pt. ► High quality Pt nanorods were obtained by calcinations process. ► Pt nanorods with a diameter of few hundred nanometers were obtained. ► Polyamide-6 nanofibers template based Pt nanorods synthesis are a feasible method. - Abstract: We report on the synthesis of platinum (Pt) nanorods by using ultrafine polyamide-6 nanofibers templates produced via electrospinning technique. These ultrafine polyamide-6 nanofibers can be utilized as the templates for growing Pt nanorods after modifying them optimally by plasma passivations. The morphological, structural, optical and electrical properties of the template assisted Pt nanorods were studied by field-emission scanning electron microscopy (FE-SEM), high-resolution transmission electron microscopy (HR-TEM), X-ray diffraction (XRD), photoluminescence (PL) and current–voltage (I–V) characteristics. The ability to fabricate the ultrafine size controlled Pt nanorods on polyamide-6 templates with optimized growth parameters in real time can be utilized for the variety of technological applications. Therefore, it is possible to obtain high quality with size control Pt nanorods. Once obtaining the high quality metal nanorods on polymer templates, the same can be adapted for the electronic device fabrication.

  3. Indoline Amide Glucosides from Portulaca oleracea: Isolation, Structure, and DPPH Radical Scavenging Activity.

    Science.gov (United States)

    Jiao, Ze-Zhao; Yue, Su; Sun, Hong-Xiang; Jin, Tian-Yun; Wang, Hai-Na; Zhu, Rong-Xiu; Xiang, Lan

    2015-11-25

    A polyamide column chromatography method using an aqueous ammonia mobile phase was developed for large-scale accumulation of water-soluble indoline amide glucosides from a medicinal plant, Portulaca oleracea. Ten new [oleraceins H, I, K, L, N, O, P, Q, R, S (1-10)] and four known [oleraceins A-D (11-14)] indoline amide glucosides were further purified and structurally characterized by various chromatographic and spectroscopic methods. The DPPH radical scavenging activities of oleraceins K (5) and L (6), with EC50 values of 15.30 and 16.13 μM, respectively, were twice that of a natural antioxidant, vitamin C; the EC50 values of the 12 other indoline amides, which ranged from 29.05 to 43.52 μM, were similar to that of vitamin C. Structure-activity relationships indicated that the DPPH radical scavenging activities of these indoline amides correlate with the numbers and positions of the phenolic hydroxy groups.

  4. New actualistic data on the ecology and energetics of hominin scavenging opportunities.

    Science.gov (United States)

    Pobiner, Briana L

    2015-03-01

    For decades, the 'hunting-scavenging debate' has been an important research focus in Plio-Pleistocene hominin behavioral ecology. Here I present new data on potential scavenging opportunities from fresh carnivore kills on a conservancy in central Kenya. This ecosystem is dominated by felids (mainly lions) and has a different carnivore guild than in many earlier studies of scavenging opportunities that took place in areas such as Ngorongoro and Serengeti in Tanzania and Maasai Mara in Kenya, where lions face high levels of inter-specific competition from bone-crunching hyenas. I found that while scavenging opportunities vary among carcasses, most carcasses retained some scavengeable resources. Excluding within-bone resources, even the scavengeable meat on 'defleshed' larger sized prey carcasses is usually substantial enough to meet the total daily caloric requirements of at least one adult male Homo erectus individual. I argue, as others have before me, that scavenging opportunities in a particular ecosystem will vary in part due to carnivore taxon, density and guild composition; prey size, biomass and community structure; and habitat (e.g., vegetation, physiography). We should expect variability in scavenging opportunities in different locales and should focus our research efforts on identifying which variables condition these differences in order to make our findings applicable to the diversity of ecological settings characterizing the past. Published by Elsevier Ltd.

  5. Optimum injection dose rate of hydrogen sulfide scavenger for treatment of petroleum crude oil

    Directory of Open Access Journals (Sweden)

    T.M. Elshiekh

    2016-03-01

    Full Text Available Hydrogen sulfide H2S scavengers are chemicals that favorably react with hydrogen sulfide gas to eliminate it and produce environmental friendly products. These products depend on the type and composition of the scavenger and the conditions at which the reaction takes place. The scavenger should be widely available and economical for industry acceptance by having a low unit cost. The optimum values of H2S scavenger injection dose rate of scavenging hydrogen sulfide from the multiphase fluid produced at different wells conditions in one of the Petroleum Companies in Egypt were studied. The optimum values of H2S scavenger injection dose rate depend on pipe diameter, pipe length, gas molar mass velocity, inlet H2S concentration and pressure. The optimization results are obtained for different values of these parameters using the software program Lingo. In general, the optimum values of H2S scavenger injection dose rate of the scavenging of hydrogen sulfide are increased by increasing of the pipe diameter and increasing the inlet H2S concentration, and decreased by increasing the pipe length, gas molar mass velocity and pressure.

  6. Energy scavenging from environmental vibration.

    Energy Technology Data Exchange (ETDEWEB)

    Galchev, Tzeno (University of Michigan); Apblett, Christopher Alan; Najafi, Khalil (University of Michigan)

    2009-10-01

    The goal of this project is to develop an efficient energy scavenger for converting ambient low-frequency vibrations into electrical power. In order to achieve this a novel inertial micro power generator architecture has been developed that utilizes the bi-stable motion of a mechanical mass to convert a broad range of low-frequency (< 30Hz), and large-deflection (>250 {micro}m) ambient vibrations into high-frequency electrical output energy. The generator incorporates a bi-stable mechanical structure to initiate high-frequency mechanical oscillations in an electromagnetic scavenger. This frequency up-conversion technique enhances the electromechanical coupling and increases the generated power. This architecture is called the Parametric Frequency Increased Generator (PFIG). Three generations of the device have been fabricated. It was first demonstrated using a larger bench-top prototype that had a functional volume of 3.7cm3. It generated a peak power of 558{micro}W and an average power of 39.5{micro}W at an input acceleration of 1g applied at 10 Hz. The performance of this device has still not been matched by any other reported work. It yielded the best power density and efficiency for any scavenger operating from low-frequency (<10Hz) vibrations. A second-generation device was then fabricated. It generated a peak power of 288{micro}W and an average power of 5.8{micro}W from an input acceleration of 9.8m/s{sup 2} at 10Hz. The device operates over a frequency range of 20Hz. The internal volume of the generator is 2.1cm{sup 3} (3.7cm{sup 3} including casing), half of a standard AA battery. Lastly, a piezoelectric version of the PFIG is currently being developed. This device clearly demonstrates one of the key features of the PFIG architecture, namely that it is suitable for MEMS integration, more so than resonant generators, by incorporating a brittle bulk piezoelectric ceramic. This is the first micro-scale piezoelectric generator capable of <10Hz operation. The

  7. Selenopentathionic and Telluropentathionic Acids as Precursors for Formation of Semiconducting Layers on the Surface of Polyamide

    Directory of Open Access Journals (Sweden)

    Skirma Zalenkiene

    2007-01-01

    Full Text Available The layers of copper chalcogenides, which were formed on the surface of semihydrophilic polymer—polyamide 6 (PA using monoselenopentathionic H2SeS4O6 and monotelluropentathionic H2TeS4O6 acids as precursors of chalcogens, were characterized. Fourier transform infrared (FT-IR and UV spectroscopy were used to monitor the effect of chalcogens on the changes in structure of PA corresponding to the concentration of the precursor's solution and an exposure time. The IR spectra of modified PA were completely different from that of the initial PA. Further interaction of chalcogenized PA with copper (II/I salt solution leads to the formation of CuxS, CuxSe, CuxTe, and mixed –CuxS–CuySe and CuxS–CuyTe layers which have different electric transport properties. The surface properties of PA after treatment are studied using AFM and XRD. The electrical resistances of layers with various composition formed over a wide concentration range 0.01–0.5 mol⋅dm−3 of precursor's solution were measured. Variation in the conductivity of layers of Cu–Se–S and Cu–Te–S on the surface of PA shows an evident increase with the increasing of the mass fraction of selenium or tellurium.

  8. Thermal conductivity of plasma modified polyethylene terephthalate and polyamide-6 layers

    Directory of Open Access Journals (Sweden)

    G. Kalacska

    2016-05-01

    Full Text Available Tribological performance of the materials greatly depends on the temperature of the contacting zones and surfaces and hence on the heat conducting behaviour of the materials. Heat conduction of polymers is, however, greatly affected even by a very narrow (few tens of nm modified layer formed on the surface after subjecting the polymer to plasma treatment. In this article the heat flow inhibiting properties of plasma modified surface layers were investigated on polyethylene terephthalate (PET and polyamide-6 (PA6 engineering polymers. Nitrogen Plasma Immersion Ion Implantation gave rise to compositional and structural changes of the polymers in a depth of 110 nm. It was found that even this thin layer exhibited significant heat flow inhibiting effect. The modified layer considerably decreased the thermal conductivity coefficient of the treated polymer and resulted in a reduced heat transmission for PET and PA6 by 33 and 28%, respectively. This new information supports and is in accordance with the former tribological results about extra friction heat generation experienced under NPIII surface layer of PA6 and PET during dry sliding.

  9. Control of biofouling on reverse osmosis polyamide membranes modified with biocidal nanoparticles and antifouling polymer brushes

    KAUST Repository

    Rahaman, Md. Saifur

    2014-01-01

    Thin-film composite (TFC) polyamide reverse osmosis (RO) membranes are prone to biofouling due to their inherent physicochemical surface properties. In order to address the biofouling problem, we have developed novel surface coatings functionalized with biocidal silver nanoparticles (AgNPs) and antifouling polymer brushes via polyelectrolyte layer-by-layer (LBL) self-assembly. The novel surface coating was prepared with polyelectrolyte LBL films containing poly(acrylic acid) (PAA) and poly(ethylene imine) (PEI), with the latter being either pure PEI or silver nanoparticles coated with PEI (Ag-PEI). The coatings were further functionalized by grafting of polymer brushes, using either hydrophilic poly(sulfobetaine) or low surface energy poly(dimethylsiloxane) (PDMS). The presence of both LBL films and sulfobetaine polymer brushes at the interface significantly increased the hydrophilicity of the membrane surface, while PDMS brushes lowered the membrane surface energy. Overall, all surface modifications resulted in significant reduction of irreversible bacterial cell adhesion. In microbial adhesion tests with E. coli bacteria, a normalized cell adhesion in the range of only 4 to 16% on the modified membrane surfaces was observed. Modified surfaces containing silver nanoparticles also exhibited strong antimicrobial activity. Membranes coated with LBL films of PAA/Ag-PEI achieved over 95% inactivation of bacteria attached to the surface within 1 hour of contact time. Both the antifouling and antimicrobial results suggest the potential of using these novel surface coatings in controlling the fouling of RO membranes. © The Royal Society of Chemistry 2014.

  10. Processing – morphology – property relationships of polyamide 6/polyethylene blend–clay nanocomposites

    Directory of Open Access Journals (Sweden)

    R. Scaffaro

    2013-10-01

    Full Text Available In this work, we studied the effect of the method of preparation and of reprocessing on the morphology and, consequently, on the physical properties of polyamide 6 (PA6/ high density polyethylene (HDPE-clay nanocomposite blends in the presence of different compatibilizers. In particular, the nanocomposites were obtained by melt mixing using a corotating twin screw extruder (E1. The blends thus obtained were re-extruded (E2 under the same operating conditions. Moreover, blends with the same final composition were produced using a masterbatch of the compatibilizer with the clay prepared in a separated stage in a batch mixer (MB. All the materials were characterized by scanning electron microscopy (SEM, transmission electron microscopy (TEM and X-ray diffractometry (XRD analyses. In addition, the rheological behaviour and the, tensile and impact, properties were evaluated. The XRD and TEM analysis showed that re-extrusion slightly improves the morphology of the nanocomposites. A further improvement of the morphology, in terms of lower clay dimension and better dispersion, was observed in the MB blends. The results of the mechanical tests showed that reprocessing (E2 induced an increase of all the properties for all the three systems. A further general increase of the mechanical properties was showed by the MB blends.

  11. High-performance multi-functional reverse osmosis membranes obtained by carbon nanotube·polyamide nanocomposite

    Science.gov (United States)

    Inukai, Shigeki; Cruz-Silva, Rodolfo; Ortiz-Medina, Josue; Morelos-Gomez, Aaron; Takeuchi, Kenji; Hayashi, Takuya; Tanioka, Akihiko; Araki, Takumi; Tejima, Syogo; Noguchi, Toru; Terrones, Mauricio; Endo, Morinobu

    2015-01-01

    Clean water obtained by desalinating sea water or by purifying wastewater, constitutes a major technological objective in the so-called water century. In this work, a high-performance reverse osmosis (RO) composite thin membrane using multi-walled carbon nanotubes (MWCNT) and aromatic polyamide (PA), was successfully prepared by interfacial polymerization. The effect of MWCNT on the chlorine resistance, antifouling and desalination performances of the nanocomposite membranes were studied. We found that a suitable amount of MWCNT in PA, 15.5 wt.%, not only improves the membrane performance in terms of flow and antifouling, but also inhibits the chlorine degradation on these membranes. Therefore, the present results clearly establish a solid foundation towards more efficient large-scale water desalination and other water treatment processes. PMID:26333385

  12. Scavenging Capacities of Some Wines and Wine Phenolic Extracts

    Directory of Open Access Journals (Sweden)

    Ioannis G. Roussis

    2005-01-01

    Full Text Available The aim of this study was to assess the ability of different wines – a sweet red, a dry red, a sweet white, and a dry white – to scavenge the stable 1,1’-diphenyl-2-picryl-hydrazyl radical (DPPH. and to determine their phenolic composition. Both red wines contained, apart from anthocyanins, also higher concentration of total phenolics, tartaric esters, and flavonols than the two white wines. All wines exhibited scavenging activity analogous to their total phenolic content. However, their phenolics differed in antiradical potency, which was visible in their EC50 values. The dry red wine, Xinomavro, had a lower EC50 value, indicating the higher antiradical potency of its phenolics. The scavenging capacities of phenolic extracts from Xinomavro red wine on hydroxyl radicals, superoxide radicals, and singlet oxygen were also assessed. Wine total extract was fractionated by extraction, and each of the three fractions was then subfractionated by column chromatography into two subfractions. Wine total extract, and its fractions and subfractions exhibited scavenging capacity on hydroxyl radicals, superoxide radicals, and singlet oxygen, indicating the activity of many wine phenolics. The most active wine extracts towards hydroxyl radicals were characterized by the high peaks of flavanols, anthocyanins and flavonols in their HPLC-DAD chromatograms. The most active extract towards superoxide radicals was rich in flavanols and anthocyanins. The characteristic phenolics of the most active wine extracts towards singlet oxygen were flavanols, flavonols and phenolic acids. The ability of all red wine phenolic extracts to scavenge singlet oxygen, along with hydroxyl and superoxide radicals, emphasizes its health functionality.

  13. Americans with Disabilities Act Scavenger Hunt

    Science.gov (United States)

    Ramsey, Ursula

    2018-01-01

    This article describes a scavenger hunt for Business Law students. Specifically, students compete in this scavenger hunt to identify accessible design features on campus to undergird their study of Title III of the Americans with Disabilities Act (ADA). Title III of the ADA prohibits public accommodations from discriminating on the basis of…

  14. Controlled Surface Modification of Polyamide 6.6 Fibres Using CaCl2/H2O/EtOH Solutions

    Directory of Open Access Journals (Sweden)

    Barbara Rietzler

    2018-02-01

    Full Text Available Polyamide 6.6 is one of the most widely used polymers in the textile industry due to its durability; however, it has rather limited modification potential. In this work, the controlled surface modification of polyamide 6.6 fibres using the solvent system CaCl2/H2O/EtOH was studied. The effects of solvent composition (relative proportions of the three components and treatment time on fibre properties were studied both in situ (with fibres in solvent and ex situ (after the solvent was washed off. The fibres swell and/or dissolve in the solvent depending on its composition and the treatment time. We believe that the fibre–solvent interaction is through complex formation between the fibre carbonyl groups and the CaCl2. On washing, there is decomplexation and precipitation of the polymer. The treated fibres exhibit greater diameters and surface roughness, structural difference between an outer shell and an inner core is observable, and water retention is higher. The solvent system is more benign than current alternatives, and through suitable tailoring of the treatment conditions, e.g., composition and time, it may be used in the design of advanced materials for storage and release of active substances.

  15. Lecithin blended polyamide-6 high aspect ratio nanofiber scaffolds via electrospinning for human osteoblast cell culture

    Energy Technology Data Exchange (ETDEWEB)

    Nirmala, R. [Bio-nano System Engineering, College of Engineering, Chonbuk National University, Jeonju, 561 756 (Korea, Republic of); Park, Hye-Min [Department of Pharmacology and Toxicology, College of Veterinary Medicine, Chonbuk National University, Jeonju 561 756 (Korea, Republic of); Navamathavan, R. [School of Advanced Materials Engineering, Chonbuk National University, Jeonju 561 756 (Korea, Republic of); Kang, Hyung-Sub [Department of Pharmacology and Toxicology, College of Veterinary Medicine, Chonbuk National University, Jeonju 561 756 (Korea, Republic of); El-Newehy, Mohamed H. [Petrochemical Research Chair, Department of Chemistry, College of Science, King Saud University, Riyadh 11451 (Saudi Arabia); Kim, Hak Yong, E-mail: khy@jbnu.ac.kr [Petrochemical Research Chair, Department of Chemistry, College of Science, King Saud University, Riyadh 11451 (Saudi Arabia); Center for Healthcare Technology and Development, Chonbuk National University, Jeonju, 561 756 (Korea, Republic of)

    2011-03-12

    In this study, we focused on the preparation and characterization of lecithin blended polyamide-6 nanofibers via an electrospinning process for human osteoblastic (HOB) cell culture applications. The morphological, structural characterizations and thermal properties of polyamide-6/lecithin nanofibers were determined by using scanning electron microscopy (SEM), field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, differential scanning calorimetry (DSC) and thermogravimetry (TGA). SEM images revealed that the nanofibers were well-oriented with good incorporation of lecithin. FT-IR results indicated the presence of amino groups of lecithin in the blended nanofibers. TGA analysis revealed that the onset degradation temperature decreased with increasing lecithin content in the blended nanofibers. The morphological features of cells attached on polyamide-6/lecithin nanofibers were confirmed by SEM. The adhesion, viability and proliferation properties of osteoblast cells on the polyamide-6/lecithin blended nanofibers were analyzed by in vitro cell compatibility test. This study demonstrated the non-cytotoxic behavior of electrospun polyamide-6/lecithin nanofibers for the osteoblast cell culture.

  16. Lecithin blended polyamide-6 high aspect ratio nanofiber scaffolds via electrospinning for human osteoblast cell culture

    International Nuclear Information System (INIS)

    Nirmala, R.; Park, Hye-Min; Navamathavan, R.; Kang, Hyung-Sub; El-Newehy, Mohamed H.; Kim, Hak Yong

    2011-01-01

    In this study, we focused on the preparation and characterization of lecithin blended polyamide-6 nanofibers via an electrospinning process for human osteoblastic (HOB) cell culture applications. The morphological, structural characterizations and thermal properties of polyamide-6/lecithin nanofibers were determined by using scanning electron microscopy (SEM), field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, differential scanning calorimetry (DSC) and thermogravimetry (TGA). SEM images revealed that the nanofibers were well-oriented with good incorporation of lecithin. FT-IR results indicated the presence of amino groups of lecithin in the blended nanofibers. TGA analysis revealed that the onset degradation temperature decreased with increasing lecithin content in the blended nanofibers. The morphological features of cells attached on polyamide-6/lecithin nanofibers were confirmed by SEM. The adhesion, viability and proliferation properties of osteoblast cells on the polyamide-6/lecithin blended nanofibers were analyzed by in vitro cell compatibility test. This study demonstrated the non-cytotoxic behavior of electrospun polyamide-6/lecithin nanofibers for the osteoblast cell culture.

  17. Sugar-Based Polyamides: Self-Organization in Strong Polar Organic Solvents.

    Science.gov (United States)

    Rosu, Cornelia; Russo, Paul S; Daly, William H; Cueto, Rafael; Pople, John A; Laine, Roger A; Negulescu, Ioan I

    2015-09-14

    Periodic patterns resembling spirals were observed to form spontaneously upon unassisted cooling of d-glucaric acid- and d-galactaric acid-based polyamide solutions in N-methyl-N-morpholine oxide (NMMO) monohydrate. Similar observations were made in d-galactaric acid-based polyamide/ionic liquid (IL) solutions. The morphologies were investigated by optical, polarized light and confocal microscopy assays to reveal pattern details. Differential scanning calorimetry was used to monitor solution thermal behavior. Small- and wide-angle X-ray scattering data reflected the complex and heterogeneous nature of the self-organized patterns. Factors such as concentration and temperature were found to influence spiral dimensions and geometry. The distance between rings followed a first-order exponential decay as a function of polymer concentration. Fourier-Transform Infrared Microspectroscopy analysis of spirals pointed to H-bonding between the solvent and the pendant hydroxyl groups of the glucose units from the polymer backbone. Tests on self-organization into spirals of ketal-protected d-galactaric acid polyamides in NMMO monohydrate confirmed the importance of the monosaccharide's pendant free hydroxyl groups on the formation of these patterns. Rheology performed on d-galactaric-based polyamides at high concentration in NMMO monohydrate solution revealed the optimum conditions necessary to process these materials as fibers by spinning. The self-organization of these sugar-based polyamides mimics certain biological materials.

  18. Synthesis of nanosilver on polyamide fabric using silver/ammonia complex.

    Science.gov (United States)

    Montazer, Majid; Shamei, Ali; Alimohammadi, Farbod

    2014-05-01

    In this paper, a novel synthesis method for nanosilver has been introduced on or within the polymeric chains of polyamide 6 fabric by using silver/ammonia complex [Ag(NH3)2](+). The silver complex was reduced directly by functional groups of polyamide chains without using any additional chemical reducing agents. The polyamide fabric was also stabilized with formation of new linkages between the polymeric chains of the nylon fabric through silver nanoparticle synthesis. The presence of nanosilver on the fabric was confirmed by UV-vis spectra, EDX patterns and XRD patterns. In addition, X-ray photoelectron spectroscopy (XPS) was utilized to identify the chemical state of silver in a range of silver oxide and silver metal. The SEM images confirmed the presence of nanosilver on the polyamide within the size of 20 and 150 nm. Excellent antibacterial properties were achieved with the treated fabrics against Staphylococcus aureus and Escherichia coli. Further, the antibacterial properties of the polyamide fabric treated with 35 mg/L silver/ammonia were durable against washing as they only decreased to 98.6% after 20 washes. In addition, some other properties of the treated fabrics including color changes, dimensional stability, water droplet adsorption, and reflectance spectrum are reported and thoroughly discussed. Copyright © 2014 Elsevier B.V. All rights reserved.

  19. Dielectric polymer: scavenging energy from human motion

    Science.gov (United States)

    Jean-Mistral, Claire; Basrour, Skandar; Chaillout, Jean-Jacques

    2008-03-01

    More and more sensors are embedded in human body for medical applications, for sport. The short lifetime of the batteries, available on the market, reveals a real problem of autonomy of these systems. A promising alternative is to scavenge the ambient energy such as the mechanical one. Up to now, few scavenging structures have operating frequencies compatible with ambient one. And, most of the developed structures are rigid and use vibration as mechanical source. For these reasons, we developed a scavenger that operates in a large frequency spectrum from quasi-static to dynamic range. This generator is fully flexible, light and does not hamper the human motion. Thus, we report in this paper an analytical model for dielectric generator with news electrical and mechanical characterization, and the development of an innovating application: scavenging energy from human motion. The generator is located on the knee and design to scavenge 0.1mJ per scavenging cycle at a frequency of 1Hz, enough to supply a low consumption system and with a poling voltage as low as possible to facilitate the power management. Our first prototype is a membrane with an area of 5*3cm and 31µm in thickness which scavenge 0.1mJ under 170V at constant charge Q.

  20. Peroxynitrite scavenging activity of herb extracts.

    Science.gov (United States)

    Choi, Hye Rhi; Choi, Jae Sue; Han, Yong Nam; Bae, Song Ja; Chung, Hae Young

    2002-06-01

    Peroxynitrite (ONOO(-)) is a cytotoxicant with strong oxidizing properties toward various cellular constituents, including sulphydryls, lipids, amino acids and nucleotides and can cause cell death, lipid peroxidation, carcinogenesis and aging. The aim of this study was to characterize ONOO(-) scavenging constituents from herbs. Twenty-eight herbs were screened for their ONOO(-) scavenging activities with the use of a fluorometric method. The potency of scavenging activity following the addition of authentic ONOO(-) was in the following order: witch hazel bark > rosemary > jasmine tea > sage > slippery elm > black walnut leaf > Queen Anne's lace > Linden flower. The extracts exhibited dose-dependent ONOO(-) scavenging activities. We found that witch hazel (Hamamelis virginiana L.) bark showed the strongest effect for scavenging ONOO(-) of the 28 herbs. Hamamelitannin, the major active component of witch hazel bark, was shown to have a strong ability to scavenge ONOO(-). It is suggested that hamamelitannin might be developed as an effective peroxynitrite scavenger for the prevention of ONOO(-) involved diseases. Copyright 2002 John Wiley & Sons, Ltd.

  1. Tribological properties of nanosized calcium carbonate filled polyamide 66 nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Itagaki, Kaito [Department of Mechanical Engineering, Graduate School of Engineering, Kogakuin University, 2665-1 Nakano, Hachioji, Tokyo 192-0015 Japan (Japan); Nishitani, Yosuke [Department of Mechanical Engineering, Faculty of Engineering, Kogakuin University, 2665-1 Nakano, Hachioji, Tokyo, 192-0015 Japan (Japan); Kitano, Takeshi [Polymer Centre, Faculty of Technology, Tomas Bata University in Zlin, T.G.M. 275, Zlin, 767 72 Czech Republic (Czech Republic); Eguchi, Kenichiro [Shiraishi Central Laboratories, 4-78 Motohama,Amagasaki,Hyogo,660-0085 Japan (Japan)

    2016-03-09

    For the purpose of developing high performance tribomaterials for mechanical sliding parts such as gears, bearings and so on, nanosized calcium carbonate (nano-CaCO{sub 3}) filled polyamide 66 (PA66) nanocomposites were investigated. The nano-CaCO{sub 3} was a kind of precipitated (colloid typed) CaCO{sub 3}, and its average particle size was 40, 80 and 150 nm. Surface treatment was performed by fatty acid on the nano-CaCO{sub 3} and its volume fraction in the nanocomposite was varied from 1 to 20vol.%. These nanocomposites were melt-mixed by a twin screw extruder and injection-molded. Tribological properties were measured by two types of sliding wear testers such as ring-on-plate type and ball-on-plate type one under dry condition. The counterface, worn surface and wear debris were observed by digital microscope and scanning electron microscope. It was found that the nano-CaCO{sub 3} has a good effect on the tribological properties, although the effect on the frictional coefficient and specific wear rate is differed by the volume fraction and the type of sliding wear modes. This is attributed to the change of wear mechanisms, which is the change of form of the transfer films on the counterface and the size of wear debris. It follows from these results that PA66/nano-CaCO{sub 3} nanocomposites may be possible to be the high performance tribomaterials.

  2. Ionic Liquids Incorporating Polyamide 6: Miscibility and Physical Properties

    Directory of Open Access Journals (Sweden)

    Xin Zheng

    2018-05-01

    Full Text Available The effects of 1-vinyl-3-butyl imidazole chloride (VBIM on the structure and properties of Polyamide 6 (PA6 were investigated systematically. It was found that PA6/VBIM blends were homogeneous without phase separation. The glass transition temperature (Tg of PA6 increased with small VBIM loadings followed by the decreasing in Tg with further increasing the amount of VBIM. The crystallization temperature decreased with the addition of VBIM because of the strong interactions between VBIM and the PA6 matrix, as well as the dilution effect when large amounts of VBIM was introduced to the matrix. According to rheological testing, small amounts of VBIM enhanced the storage modulus and melt viscosity of PA6. Tensile tests also show an increase in strength and modulus at relatively low loadings of VBIM. The strength of PA6 with only 1 wt % VBIM improved by 108% compared to that of neat PA6. Fourier transform infrared (FTIR investigations revealed that the ions of VBIM preferred to form hydrogen bonds with amide groups in PA6. Therefore, VBIM acts as physical connection point for the neighboring PA6 molecular chains. The specific interactions between VBIM and PA6 account not only for the enhanced melt viscosity of PA6, but also for the improved mechanical properties. Moreover, outstanding antistatic property was also observed. The surface resistivity of the sample with 1 wt % VBIM was 1.50 × 1010 Ω/sq, which means good electric dissipation property.

  3. Hybrid membranes of polyamide applied in treatment of waste water

    Energy Technology Data Exchange (ETDEWEB)

    Medeiros, Keila Machado de; Araujo, Edcleide Maria; Lira, Helio de Lucena, E-mail: keilamachadodemedeiros@gmail.com [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Departamento de Engenharia de Materiais; Lima, Diego de Farias; Lima, Carlos Antonio Pereira de [Universidade Estadual da Paraiba (UEPB), Campina Grande, PB (Brazil). Departamento de Engenharia Sanitaria e Ambiental

    2017-03-15

    In this work, it was prepared hybrid membranes of polyamide6 (PA6) with montmorillonite (MMT) and porogenic agent (CaCl{sub 2} ). The hybrid membranes with CaCl{sub 2} were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), porosimetry by mercury intrusion (PMI), flux measurements and rejection. By means of X-ray diffraction, it was revealed that the hybrid membranes with CaCl{sub 2} have an exfoliated and/or partially exfoliated structure. For FTIR and DSC of hybrid membranes with CaCl{sub 2} , it was found that the spectra and the crystalline melting temperature remained virtually unchanged compared to PA6 membrane. From the SEM images, it was observed that the addition of the MMT and the CaCl{sub 2} in the membrane of PA6 caused an increase in the amount of pores the surface and cross section of these membranes. By PMI, it was observed that the presence of MMT and CaCl{sub 2} in the membrane caused an increase in the average diameters of pores. The water-oil separation tests, indicated a significant reduction of oil in the permeate, allowing treatment of wastewater contaminated with oil. (author)

  4. Hybrid membranes of polyamide applied in treatment of waste water

    International Nuclear Information System (INIS)

    Medeiros, Keila Machado de; Araujo, Edcleide Maria; Lira, Helio de Lucena; Lima, Diego de Farias; Lima, Carlos Antonio Pereira de

    2017-01-01

    In this work, it was prepared hybrid membranes of polyamide6 (PA6) with montmorillonite (MMT) and porogenic agent (CaCl 2 ). The hybrid membranes with CaCl 2 were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), porosimetry by mercury intrusion (PMI), flux measurements and rejection. By means of X-ray diffraction, it was revealed that the hybrid membranes with CaCl 2 have an exfoliated and/or partially exfoliated structure. For FTIR and DSC of hybrid membranes with CaCl 2 , it was found that the spectra and the crystalline melting temperature remained virtually unchanged compared to PA6 membrane. From the SEM images, it was observed that the addition of the MMT and the CaCl 2 in the membrane of PA6 caused an increase in the amount of pores the surface and cross section of these membranes. By PMI, it was observed that the presence of MMT and CaCl 2 in the membrane caused an increase in the average diameters of pores. The water-oil separation tests, indicated a significant reduction of oil in the permeate, allowing treatment of wastewater contaminated with oil. (author)

  5. Improved Mechanical Properties of Compatibilized Polypropylene/Polyamide-12 Blends

    Directory of Open Access Journals (Sweden)

    Nora Aranburu

    2015-01-01

    Full Text Available Compatibilized blends of polypropylene (PP and polyamide-12 (PA12 as a second component were obtained by direct injection molding having first added 20% maleic anhydride-modified copolymer (PP-g-MA to the PP, which produced partially grafted PP (gPP. A nucleating effect of the PA12 took place on the cooling crystallization of the gPP, and a second crystallization peak of the gPP appeared in the PA12-rich blends, indicating changes in the crystalline morphology. There was a slight drop in the PA12 crystallinity of the compatible blends, whereas the crystallinity of the gPP increased significantly in the PA12-rich blends. The overall reduction in the dispersed phase particle size together with the clear increase in ductility when gPP was used instead of PP proved that compatibilization occurred. Young’s modulus of the blends showed synergistic behavior. This is proposed to be both due to a change in the crystalline morphology of the blends on the one hand and, on the other, in the PA12-rich blends, to the clear increase in the crystallinity of the gPP phase, which may, in turn, have been responsible for the increase in its continuity and its contribution to the modulus.

  6. Fluorescent detection of C-reactive protein using polyamide beads

    Science.gov (United States)

    Jagadeesh, Shreesha; Chen, Lu; Aitchison, Stewart

    2016-03-01

    Bacterial infection causes Sepsis which is one of the leading cause of mortality in hospitals. This infection can be quantified from blood plasma using C - reactive protein (CRP). A quick diagnosis at the patient's location through Point-of- Care (POC) testing could give doctors the confidence to prescribe antibiotics. In this paper, the development and testing of a bead-based procedure for CRP quantification is described. The size of the beads enable them to be trapped in wells without the need for magnetic methods of immobilization. Large (1.5 mm diameter) Polyamide nylon beads were used as the substrate for capturing CRP from pure analyte samples. The beads captured CRP either directly through adsorption or indirectly by having specific capture antibodies on their surface. Both methods used fluorescent imaging techniques to quantify the protein. The amount of CRP needed to give a sufficient fluorescent signal through direct capture method was found suitable for identifying bacterial causes of infection. Similarly, viral infections could be quantified by the more sensitive indirect capture method. This bead-based assay can be potentially integrated as a disposable cartridge in a POC device due to its passive nature and the small quantities needed.

  7. Structural comparison of nanocomposites membranes of polyamide 6 and polyamide 6.6 with a regional clay; Comparacao estrutural de membranas de nanocompositos de poliamida 6 e poliamida 6.6 com uma argila regional

    Energy Technology Data Exchange (ETDEWEB)

    Leite, A M.D.; Medeiros, V N; Paz, R A; Araujo, E M; Lira, H.L., E-mail: amandamelissa.lins@yahoo.com.b [Universidade Federal de Campina Grande (UAEMa/UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais; Ito, Edson N [Universidade Federal do Rio Grande do Norte (DEMat/UFRN), Natal, RN (Brazil). dept. de Engenharia de Materiais

    2010-07-01

    Polyamide membranes do not require wetting agents because they are hydrophilic membranes and show great interest in the separation of aqueous solutions. With this, there is the interest to produce membranes from nanocomposites (polyamide 6 and polyamide 6.6)/organoclay), using the technique of isothermal immersion-precipitation in a bath with distilled water. The objective of this work was to produce, characterize and compare nanocomposites of polyamide 6 and polyamide 6.6/organoclay for use in the preparation of membranes. The nanocomposites were produced with 3 wt% of clay organically modified by quaternary ammonium salt (Cetremide) and were characterized by XRD and TEM. The nanocomposites presented an exfoliated/partially exfoliated structure. The membranes were characterized by SEM and presented a dense layer (selective skin) and another layer with uniform pores distributed along the membrane. (author)

  8. Vibration electrospinning of Polyamide-66/Multiwall Carbon Nanotube Nanocomposite: introducing electrically conductive, ultraviolet blocking and antibacterial properties

    Directory of Open Access Journals (Sweden)

    Zohoori Salar

    2017-09-01

    Full Text Available Fabrication of electro-conductive fiber is a novel process. Nanocomposites of multiwall carbon nanotube/polyamide66 were produced by electrospinning with different amounts of multiwall carbon nanotube. Field emission scanning electron microscope and Fourier transform infrared spectroscopy of samples proved the existence of multiwall carbon nanotube distribution in polyamide 66 nanofibers. Results showed that electro conductivity of electrospun multiwall carbon nanotube/polyamide 66 nano fiber has increased in comparison with electrospun polyamide 66. Moreover, UV blocking of samples was investigated which has shown that using multiwall carbon nanotube in polyamide 66 increases UV blocking of fibers. Furthermore, anti-bacterial activity of nanocomposite showed that these nanocomposites have antibacterial property against both Staphylococcus Aureus and Escherichia Coli bacteria according to AATCC test method.

  9. Effect of repair resin type and surface treatment on the repair strength of polyamide denture base resin.

    Science.gov (United States)

    Gundogdu, Mustafa; Yanikoglu, Nuran; Bayindir, Funda; Ciftci, Hilal

    2015-01-01

    The purpose of the present study was to evaluate the effects of different repair resins and surface treatments on the repair strength of a polyamide denture base material. Polyamide resin specimens were prepared and divided into nine groups according to the surface treatments and repair materials. The flexural strengths were measured with a 3-point bending test. Data were analyzed with a 2-way analysis of variance, and the post-hoc Tukey test (α=0.05). The effects of the surface treatments on the surface of the polyamide resin were examined using scanning electron microscopy. The repair resins and surface treatments significantly affected the repair strength of the polyamide denture base material (p0.05). The flexural strength of the specimens repaired with the polyamide resin was significantly higher than that of those repaired with the heat-polymerized and autopolymerizing acrylic resins.

  10. MRI diagnosis of the complications of polyamide hydrogel injection for augmentation mammoplasty

    International Nuclear Information System (INIS)

    Chen Xueqiang; Chen Pingyou; Zhang Yunshu; Luo Qinghua; Xu Rong

    2005-01-01

    Objective: To analyze MRI findings and its clinical significance in complications of polyamide hydrogel injection for augmentation mammoplasty. Methods: The complication findings of MR imaging in 20 cases with polyamide hydrogel injection for augmentation mammoplasty were retrospectively reviewed and analyzed. Results: In 20 patients, 26 breasts suffered from complications, including infection (n=5) with pieces of long T 1 and long T 2 signals, aseptic inflammation (n=2) with pieces of slight long T 1 and moderate T 2 signals, hard nodule (n=10) with long T 1 and long T 2 signals, and rupture (n=5) with pieces and nodes of long T 1 and long T 2 signals on MR images. Conclusion: MRI has the great diagnostic value in the detection of complications after polyamide hydrogel injection for augmentation mammoplasty, and it should be taken as the first diagnostic choice. (authors)

  11. Retention and Deformation of Cobalt-Chromium and High-Impact Polyamide Clasps

    Directory of Open Access Journals (Sweden)

    Övül Kümbüloğlu

    2018-04-01

    Full Text Available Objective: The use of metal clasps especially in anterior region may cause aesthetic problems. Polyamide resin has been suggested as an alternative aesthetic denture clasp material. This study compared the retentive force and deformation of cobalt-chromium and polyamide clasps after 36 months of simulated clinical use. Materials and Methods: The retentive force for clasp removal was measured in distilled water using a custom-made apparatus with intervals corresponding to 0, 6, 12, 18, 24, 30 and 36 months of simulated clinical use. The distance (mm between the retentive and reciprocal clasp tips was measured using a microscope before and after the insertion-removal procedures. Results: Significant difference was observed in distance between clasp tips for metal clasps between baseline and 36 months for molars and premolars (p0.05. Conclusion: Polyamide clasps could be alternative to metal clasps particularly on premolars with reliable retention and deformation.

  12. Orientation and the extent of exfoliation of clay on scratch damage in polyamide 6 nanocomposites

    International Nuclear Information System (INIS)

    Dasari, Aravind; Yu Zhongzhen; Mai Yiuwing; Kim, Jang-Kyo

    2008-01-01

    The major objectives of this work are to understand the effects of organoclay, its extent of exfoliation and orientation, and indenter geometry on the scratch characteristics of polyamide 6/organoclay nanocomposites. Two different organically treated clays are used for this purpose and their structural parameters in a polyamide 6 matrix quantified. It is shown that, while the material properties are important for scratching resistance, they are not the only determinants of the scratch performance of materials. Further, despite proving beneficial to scratch resistance, in terms of residual depth, the presence (and exfoliation) of organoclay promotes the formation of brittle cracks during scratching. But with no organoclay layers, plastic flow controls the scratch damage in neat polyamide 6 with large residual depths. Factors such as orientation of clay layers and variations of indenter tip geometry also exert dominant effects on scratch penetration resistance and damage. Additionally, significant plastic flow and rotation of organoclay layers from the original configuration are observed underneath the sliding indenter

  13. Aromatic-aliphatic polyamide/montmorillonite clay nanocomposite materials: Synthesis, nanostructure and properties

    International Nuclear Information System (INIS)

    Zulfiqar, Sonia; Ahmad, Zahoor; Ishaq, Muhammad; Sarwar, Muhammad Ilyas

    2009-01-01

    New type of aromatic-aliphatic polyamide/montmorillonite nanocomposites were produced using solution intercalation technique in dimethylacetamide. The modification of clay was carried out with ammonium salt of long chain alkyl amine. The nanocomposites were probed for organoclay dispersion, mechanical, thermal and water absorption measurements. Formation of delaminated and intercalated nanostructures was confirmed by X-ray diffraction and TEM studies. Improvement in tensile strength and modulus was observed for nanocomposites with optimum organoclay content (8-wt.%). Thermogravimetric analysis indicated an increase in thermal stability of nanocomposites as compared to pristine polyamide. Differential scanning calorimetric results revealed increase in glass transition temperatures (T g ) with augmenting organoclay in the nanocomposites. Water uptake of the nanocomposites reduced than the neat polyamide rendering decreased permeability.

  14. Aromatic-aliphatic polyamide/montmorillonite clay nanocomposite materials: Synthesis, nanostructure and properties

    Energy Technology Data Exchange (ETDEWEB)

    Zulfiqar, Sonia [Department of Chemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Ahmad, Zahoor [Department of Chemistry, Faculty of Science, Kuwait University, P. O. Box: 5969, Safat 13060 (Kuwait); Ishaq, Muhammad [Department of Chemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Sarwar, Muhammad Ilyas, E-mail: ilyassarwar@hotmail.com [Department of Chemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Department of Materials Science and Engineering, University of Delaware, Newark, DE 19716 (United States)

    2009-11-15

    New type of aromatic-aliphatic polyamide/montmorillonite nanocomposites were produced using solution intercalation technique in dimethylacetamide. The modification of clay was carried out with ammonium salt of long chain alkyl amine. The nanocomposites were probed for organoclay dispersion, mechanical, thermal and water absorption measurements. Formation of delaminated and intercalated nanostructures was confirmed by X-ray diffraction and TEM studies. Improvement in tensile strength and modulus was observed for nanocomposites with optimum organoclay content (8-wt.%). Thermogravimetric analysis indicated an increase in thermal stability of nanocomposites as compared to pristine polyamide. Differential scanning calorimetric results revealed increase in glass transition temperatures (T{sub g}) with augmenting organoclay in the nanocomposites. Water uptake of the nanocomposites reduced than the neat polyamide rendering decreased permeability.

  15. Mechanical and rheological properties of nanocomposites of polyamide 6 with national organoclay

    International Nuclear Information System (INIS)

    Paz, Rene Anisio da; Leite, Amanda Melissa Damiao; Araujo, Edcleide Maria; Melo, Tomas Jeferson Alves de; Pessan, Luiz Antonio; Passador, Fabio Roberto

    2013-01-01

    Nanocomposites of polyamide 6 with organoclay were prepared by melt intercalation and their rheological and mechanical properties were studied. The clay was treated with the quaternary ammonium salt (Cetremide) and characterized by Infrared Spectroscopy (FTIR) and X-ray diffraction (XRD). The results showed the incorporation of salt in the clay and its organophilization. A master was prepared with PA6/clay (1:1) by weight and this was added to the pure polyamide 6 to reach the nominal proportion of 3% of clay, using a co-rotational twin screw extruder. The samples were molded by injection and characterized by: capillary rheometry, XRD, TEM and mechanical testing (tensile and impact). The results of capillary rheometry showed that the presence of organoclay in the PA6 increased the viscosity of the systems. With XRD and TEM, it was verified that all systems presented predominantly exfoliated structure. The tensile properties of the nanocomposites were better than those of pure polyamide 6. (author)

  16. Scavenger receptors in homeostasis and immunity.

    Science.gov (United States)

    Canton, Johnathan; Neculai, Dante; Grinstein, Sergio

    2013-09-01

    Scavenger receptors were originally identified by their ability to recognize and to remove modified lipoproteins; however, it is now appreciated that they carry out a striking range of functions, including pathogen clearance, lipid transport, the transport of cargo within the cell and even functioning as taste receptors. The large repertoire of ligands recognized by scavenger receptors and their broad range of functions are not only due to the wide range of receptors that constitute this family but also to their ability to partner with various co-receptors. The ability of individual scavenger receptors to associate with different co-receptors makes their responsiveness extremely versatile. This Review highlights recent insights into the structural features that determine the function of scavenger receptors and the emerging role that these receptors have in immune responses, notably in macrophage polarization and in the pathogenesis of diseases such as atherosclerosis and Alzheimer's disease.

  17. Role of antioxidant scavenging enzymes and extracellular ...

    African Journals Online (AJOL)

    ChithrashreeGS

    2012-08-23

    Aug 23, 2012 ... peroxidase are two important antioxidant scavenging enzymes involved in ... Catalase was assayed using the method of Beers and Sizer. (1951) with .... yeast dextrose calcium carbonate agar (YDC) medium. Catalase and ...

  18. Flavonoids as scavengers of nitric oxide radical.

    NARCIS (Netherlands)

    van Acker, S.A.B.E.; Tromp, M.N.J.L.; Haenen, G.R.M.M.; van der Vijgh, W.J.F.; Bast, A.

    1995-01-01

    Flavonoids are a group of naturally occurring compounds used, e.g., in the treatment of vascular endothelial damage. They are known to be excellent scavengers of oxygen free radicals. Since the nitric oxide radical (

  19. Morphologic characterization for XRD and TEM of polyamide 6 and 66 nanocomposites with bentonite regional clay

    International Nuclear Information System (INIS)

    Leite, Amanda M.D.; Medeiros, Vanessa da N.; Maia, Larissa F.; Araujo, Edcleide M.; Lira, Helio L.

    2009-01-01

    Polyamide 6 and 66 nanocomposites with clay consisting of silicates layer from Paraiba were produced. The clay was modified being used the quaternary salt of ammonium Cetremide, this so there is a better interaction of the clay with polymeric matrix. The clay without treatment (MMT) and treated clay was evaluated by XRD that showed the insertion of the salt molecules into silicates layer. The nanocomposites were obtained from polyamide 6 and 66 were verified that these presented morphological structure composed of exfoliated/partially exfoliated, analyzed by XRD and TEM. (author)

  20. Mechanisms of formation and destruction of nitrogen oxides during polyamide incineration in a fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Hahnel, F; Gadiou, R; Prado, G [Univ. de Haute Alsace, Mulhouse (France). Lab. de Gestion des Risques et Environnement

    1998-09-01

    In order to study the incineration of nitrogen-containing polymers, a fludized bed has been built. This paper reports the results for polyamide 6-6 incineration. The main nitrogen containing species have been identified, and the axial profiles of concentration of nitrogen oxides, HCN and NH3 have been measured. The main steps of decomposition of the polyamide were identified. We present an experimental investigation of the influence of operating parameters (temperature, excess air) on the formation and reduction of polymer combustion products. The yields of conversion of nitrogen to the different N-species have been calculated as a function of excess air in the fluidized bed. (orig.)

  1. Rheological changes of polyamide 12 under oscillatory shear

    Science.gov (United States)

    Mielicki, C.; Gronhoff, B.; Wortberg, J.

    2014-05-01

    Changes in material properties as well as process deviation prevent Laser Sintering (LS) technology from manufacturing of quality assured parts in a series production. In this context, the viscosity of Polyamide 12 (PA12) is assumed to possess the most significant influence, as it determines the sintering velocity, the resistance towards melt formation and the bonding strength of sintered layers. Moreover, the viscosity is directly related to the structure of the molten polymer. In particular, it has been recently reported that LS process conditions lead to structural changes of PA12 affecting viscosity and coalescence of adjacent polymer particles, i.e. melt formation significantly. Structural change of PA12 was understood as a post condensation. Its influence on viscosity was described by a time and temperature depending rheological model whereas time dependence was considered by a novel structural change shift factor which was derived from melt volume rate data. In combination with process data that was recorded using online thermal imaging, the model is suitable to control the viscosity (processability of the material) as result of material and process properties. However, as soon as laser energy is exposed to the powder bed PA12 undergoes a phase transition from solid to molten state. Above the melting point, structural change is expected to occur faster due to a higher kinetic energy and free volume of the molten polymer. Oscillatory shear results were used to study the influence of aging time and for validation of the novel structural change shift factor and its model parameters which were calibrated based on LS processing condition.

  2. Surface modification of polyamide reverse osmosis membrane with organic-inorganic hybrid material for antifouling

    Science.gov (United States)

    Zhang, Yang; Wan, Ying; Pan, Guoyuan; Yan, Hao; Yao, Xuerong; Shi, Hongwei; Tang, Yujing; Wei, Xiangrong; Liu, Yiqun

    2018-03-01

    A series of thin-film composite reverse osmosis membranes based on polyamide have been modified by coating the polyvinyl alcohol and 3-mercaptopropyltriethoxysilane aqueous solution prepared by a sol-gel process on the membrane surface, followed by thermal crosslinking treatment. In order to improve the hydrophilicity of the modified TFC membranes, the membranes were then immersed into H2O2 aqueous solution to convert -SH into -SO3H. The resulting TFC membranes were characterized by SEM, AFM, ATR-FTIR, streaming potential, XPS as well as static contact angle. After surface modification with the organic-inorganic hybrid material, the TFC membranes show increased NaCl rejection and decreased water flux with increasing 3-mercaptopropyltrimethoxysilane content in coating solution. The optimal modification membrane (PA-SMPTES-0.8) exhibits a NaCl rejection of 99.29%, higher than that (97.20%) of the virgin PA membrane, and a comparable water flux to virgin PA membrane (41.7 L/m2 h vs 47.9 L/m2 h). More importantly, PA-SMPTES-0.8 membrane shows much more improved fouling resistance to BSA than virgin PA and PVA modified PA (PA-PVA-1.0) membranes. PA-SMPTES-0.8 membrane loses about 13% of the initial flux after BSA fouling for 12 h, which is lower than that of virgin PA and PA-PVA-1.0 membranes (42% and 18%). Furthermore, the flux recovery of PA-SMPTES-0.8 membrane reaches 94% after cleaning. Thus the TFC membranes modified by this organic-inorganic hybrid technology show potential applications as antifouling RO membrane for desalination and purification.

  3. Effects of Electron Beam Irradiation on Binary Polyamide-6 Blends with Metallocene Copolymers

    International Nuclear Information System (INIS)

    Rosales, C.

    2006-01-01

    A versatile way to produce new materials with high Izod impact strength and reduced heat deformations is the irradiation of compatibilized blends. The effect of electron beam irradiation and different types of dispersed phase grafted copolymers on thermal and mechanical properties, and SEM morphology of polyamide-6 (PA-6) blends were investigated. Two metallocene copolymers (mEPDM and mPOE) grafted in-situ with maleic anhydride and two commercial maleated copolymers (EPDM-g-MA and mEPR-g-MA) were employed in binary blends with PA6 as matrix. The blends were prepared by extrusion with a composition of 80 wt. % of PA-6. The influence of the radical or functional groups generated in the grafting and the irradiation processes (25, 50, 100 and 200 kGy) was found by ATR-FTIR. The blends exhibited the characteristic thermal behavior of immiscible systems. All compatibilizers employed influenced the melting and crystallization behavior of the blend components without irradiation and an improvement in interface adhesion was clearly observed by SEM micrographs. The sizes of the dispersed phase in the non-irradiated reactive blends were in agreement with the viscosity ratios of the blend components. High toughness materials were obtained with ethylene-polypropylene-diene (mEPDM) grafted copolymers without significant variations in their thermal properties and Izod impact strength at room temperature and -30 degree with the irradiation doses. However, the toughness of the blends with grafted metallocene polyethylenes was affected by the irradiation doses employed. Therefore, the gel content and tensile properties of the samples depended on the chain scission, crosslinking and/or grafting reactions of the blend components

  4. Dual-skinned polyamide/poly(vinylidene fluoride)/cellulose acetate membranes with embedded woven

    KAUST Repository

    Duong, Phuoc H.H.

    2016-08-31

    We propose multilayer membranes including (i) a thin selective polyamide (PA) layer prepared via interfacial polymerization, (ii) a poly (vinylidene fluoride) (PVDF) asymmetric porous support with high adhesion to the PA layer and high mechanical strength, (iii) a strong woven fabric, and (iv) fouling resistant porous cellulose acetate (CA) layer. The PA layer rejects solutes of the draw solution. The PVDF/woven fabric/CA (PVDF/CA) integrated layer performs as a mechanical support with unique properties for forward osmosis (FO) applications. It consists of a modified PVDF top layer suitable for the deposition of a PA layer and a highly hydrophilic bottom layer (CA) with a tunable pore size to minimize foulant deposition and intrusion onto and into the support. The experimental results using bovine serum albumin (BSA) as a model foulant show that the presence of the CA layer at the bottom of the FO membrane (PA/PVDF/CA) reduces 75% fouling propensity compared to the simple FO membrane made of PVDF, woven fabric and PA (PA/PVDF). Fouling tests with 2000 ppm oily feed faced the bottom of the FO membranes further indicate the superiority of the PA/PVDF/CA membrane compared to the PA/PVDF membrane. Moreover, the bottom CA layer can be adjusted with a flexible range of pore size, varied from sub-micron to sub-nanometer depending on the feed composition. The newly developed multilayer FO membrane has comparable performance to the state-of-the-art membrane with added tailored fouling resistance for specific wastewater feeds.

  5. Thermoplastic composite wind turbine blades : Vacuum infusion technology for anionic polyamide-6 composites

    NARCIS (Netherlands)

    van Rijswijk, K.

    2007-01-01

    Due to the increasing costs of fossil fuels and the improved efficiency of wind turbines in the last decade, wind energy has become increasingly cost-efficient and is well on its way of becoming a mainstream source of energy. To maintain a continuous reduction in costs it is necessary to increase

  6. The influence of multiscale fillers reinforcement into impact resistance and energy absorption properties of polyamide 6 and polypropylene nanocomposite structures

    International Nuclear Information System (INIS)

    Silva, Francesco; Njuguna, James; Sachse, Sophia; Pielichowski, Krzysztof; Leszczynska, Agnieszka; Giacomelli, Marco

    2013-01-01

    Highlights: ► Significant improvement in PA composites impact resistance performance. ► Decrease in energy absorption capabilities of PP, this phenomenon is explained. ► Positive effects on mechanical and interphase properties of the matrix material. ► Transition from brittle to ductile fracture mode established. ► Two different toughening mechanisms were observed and explained. - Abstract: Three-phase composites (thermoplastic polymer, glass-fibres and nano-particles) were investigated as an alternative to two-phase (polymer and glass-fibres) composites. The effect of matrix and reinforcement material on the energy absorption capabilities of composite structures was studied in details in this paper. Dynamic and quasi-static axial collapse of conical structures was conducted using a high energy drop tower, as well as Instron universal testing machine. The impact event was recorded using a high-speed camera and the fracture surface was investigated with scanning electron microscopy (SEM). Attention was directed towards the relation between micro and macro fracture process with crack propagation mechanism and energy absorbed by the structure. The obtained results indicated an important influence of filler and matrix material on the energy absorption capabilities of the polymer composites. A significant increase in specific energy absorption (SEA) was observed in polyamide 6 (PA6) reinforced with nano-silica particles and glass-spheres, whereas addition of montmorillonite (MMT) caused a decrease in that property. On the other hand, very little influence of the secondary reinforcement on the energy absorption capabilities of polypropylene (PP) composites was found

  7. Boundary scavenging in the Pacific Ocean

    International Nuclear Information System (INIS)

    Anderson, R.F.; Lao, Y.; Broecker, W.S.; Trumbore, S.E.; Hofmann, H.J.; Wolfli, W.

    1990-01-01

    Concentrations of U, Th, 231 Pa and 10 Be were measured in Holocene sediments from two cores collected off the west coast of South America, two cores from the East Pacific Rise, two from the equatorial Pacific and one from the south Pacific central gyre. Our results, together with data from 5 cores reported in the literature, show that boundary scavenging plays a major role in the removal of 10 Be from the Pacific Ocean. Deposition rates of 10 Be at three margin sites are more than an order of magnitude greater than at sites of red clay accumulation in the deep central Pacific. Deposition of 231 Pa is 4 to 5-fold greater at the margin sites. The residence time of 10 Be with respect to chemical scavenging, defined as its inventory in the water column divided by its rate of removal to the sediments, varies regionally from >1000 years at the red-clay sites in the deep central Pacific to ∝100 years at the margin sites. Different factors control boundary scavenging of Pa and Be. For example, scavenging of 231 Pa is enhanced by metal-oxide coatings of particles, whereas this seems to have little influence on the scavenging of 10 Be. (orig.)

  8. Blood Glutamate Scavenging: Insight into Neuroprotection

    Directory of Open Access Journals (Sweden)

    Alexander Zlotnik

    2012-08-01

    Full Text Available Brain insults are characterized by a multitude of complex processes, of which glutamate release plays a major role. Deleterious excess of glutamate in the brain’s extracellular fluids stimulates glutamate receptors, which in turn lead to cell swelling, apoptosis, and neuronal death. These exacerbate neurological outcome. Approaches aimed at antagonizing the astrocytic and glial glutamate receptors have failed to demonstrate clinical benefit. Alternatively, eliminating excess glutamate from brain interstitial fluids by making use of the naturally occurring brain-to-blood glutamate efflux has been shown to be effective in various animal studies. This is facilitated by gradient driven transport across brain capillary endothelial glutamate transporters. Blood glutamate scavengers enhance this naturally occurring mechanism by reducing the blood glutamate concentration, thus increasing the rate at which excess glutamate is cleared. Blood glutamate scavenging is achieved by several mechanisms including: catalyzation of the enzymatic process involved in glutamate metabolism, redistribution of glutamate into tissue, and acute stress response. Regardless of the mechanism involved, decreased blood glutamate concentration is associated with improved neurological outcome. This review focuses on the physiological, mechanistic and clinical roles of blood glutamate scavenging, particularly in the context of acute and chronic CNS injury. We discuss the details of brain-to-blood glutamate efflux, auto-regulation mechanisms of blood glutamate, natural and exogenous blood glutamate scavenging systems, and redistribution of glutamate. We then propose different applied methodologies to reduce blood and brain glutamate concentrations and discuss the neuroprotective role of blood glutamate scavenging.

  9. Effects of reuse and bleach/formaldehyde reprocessing on polysulfone and polyamide hemodialyzers.

    Science.gov (United States)

    Cornelius, Rena M; McClung, W Glenn; Barre, Paul; Esguerra, Fe; Brash, John L

    2002-01-01

    The surface features, morphology, and blood interactions of fibers from pristine, bleach/formaldehyde reprocessed, and reused Fresenius Polysulfone High Flux (Hemoflow F80B) hemodialyzers and Gambro Polyflux 21S Polyamide hemodialyzers have been studied. SEM images of fibers from both hemodialyzer types revealed a dense skin layer on the inner surface and a relatively thick porous layer on the outer surface. The 21S polyamide support layer consisted of interconnected highly porous structures. Environmental scanning electron microscopy and atomic force microscopy images of both membrane types showed alterations in morphology due to reprocessing and reuse; however the changes were more marked for the 21S polyamide dialyzers. Fluorescence microscopy images showed only minimal fluorescence associated with the fibers after patient use and reprocessing, suggesting that blood derived deposits were removed by processing. The protein layers formed on pristine and reused hemodialyzer membranes during clinical use were studied using SDS-PAGE and immunoblotting. Before bleach/formaldehyde treatment, protein layers of considerable amount and complexity were found on the blood side of singly and multiply used dialyzers. Proteins adsorbed on the dialysate side were predominantly in the molecular mass region below 30 kDa. However, some higher molecular mass proteins were detected on the dialysate side of the 21 S polyamide dialyzers. Very little protein was detected on dialyzers that were treated with bleach/formaldehyde after dialysis, regardless of whether they had been used/reprocessed once or 12 times.

  10. Radiolytic crosslinking and chain scission in aliphatic and alkyl-aromatic polyamides: Pt. 2

    International Nuclear Information System (INIS)

    Lyons, B.J.; Glover, L.C. Jr.

    1991-01-01

    Regression analysis of the radiation parameters of nine aliphatic polyamides exposed to ionizing radiation leads to the conclusion that the decline in the ratio of chain scission to crosslinking in higher aliphatic polyamides is best related to the linear increase in the methylene content of, or the number of methylene groups in, the polyamide repeat unit. G(crosslink)[G(X)] and G(chain scission) [G(CS)] values, however, do not correlate well with either of these parameters. Rather it is found that the major determinant of yields [about 80-85% of the variation for G(X), 70% for G(CS)] is the number of hydrogen atoms or methylene groups in the amine residue. Although, logically, the yields of crosslinks and chain scissions in polyamides would be expected to tend to that of polyethylene as the number of methylene groups in the repeat unit increases, use of two models assuming an exponential trend to the G(X) value characteristic of polyethylene in the analysis did not provide better fits to the data than the simple linear model referred to above. Indeed, the assumption of a significant exponential trend factor led to a marked drop in the goodness of fit. (author)

  11. Comparison of Three Different Methods for Pile Integrity Testing on a Cylindrical Homogeneous Polyamide Specimen

    Science.gov (United States)

    Lugovtsova, Y. D.; Soldatov, A. I.

    2016-01-01

    Three different methods for pile integrity testing are proposed to compare on a cylindrical homogeneous polyamide specimen. The methods are low strain pile integrity testing, multichannel pile integrity testing and testing with a shaker system. Since the low strain pile integrity testing is well-established and standardized method, the results from it are used as a reference for other two methods.

  12. Living Polycondensation: Synthesis of Well-Defined Aromatic Polyamide-Based Polymeric Materials

    KAUST Repository

    Alyami, Mram Z.

    2016-11-01

    Chain growth condensation polymerization is a powerful tool towards the synthesis of well-defined polyamides. This thesis focuses on one hand, on the synthesis of well-defined aromatic polyamides with different aminoalkyl pendant groups with low polydispersity and controlled molecular weights, and on the other hand, on studying their thermal properties. In the first project, well-defined poly (N-octyl-p-aminobenzoate) and poly (N-butyl-p-aminobenzoate) were synthesized, and for the first time, their thermal properties were studied. In the second project, ethyl4-aminobenzoate, ethyl 4-octyl aminobenzoate and 4-(hydroxymethyl) benzoic acid were used as novel efficient initiators of ε-caprolactone with t-BuP2 as a catalyst. Macroinitiator and Macromonomer of poly (ε-caprolactone) were synthesized with ethyl 4-octyl aminobenzoate and ethyl 4-aminobenzoate as initiators to afford polyamide-block-poly (ε-caprolactone) and polyamide-graft-poly (ε-caprolactone) by chain growth condensation polymerization (CGCP). In the third project, a new study has been done on chain growth condensation polymerization to discover the probability to synthesize new polymers and studied their thermal properties. For this purpose, poly (N-cyclohexyl-p-aminobenzoate) and poly (N-hexyl-p-aminobenzoate) were synthesized with low polydispersity and controlled molecular weights.

  13. Comparison of the properties polyamide 6.6 surfaces treated by plasma and by ionizing radiation

    International Nuclear Information System (INIS)

    Irineu, Rosa Maria da Silva

    2010-01-01

    This study aims to compare the surface properties of polyamide 6.6 plasma treatment and ionizing radiation, as well as determine the best technique and condition of the surface activation, adhesion of the same order and polyacrylic rubber used in manufacturing of automotive retainers. Treatment of polyamide 6.6 plasma was performed using an equipment 'Electronic Diener - Plasma - Surface-Technology LFG40' with nitrogen gas at a pressure of 1.40 kg/cm 2 . Samples of polyamide 6.6 were also treated with ionizing radiation, atmospheric pressure and in vacuum, using an industrial electron accelerator, Dynamitron JOB 188 with radiation dose of 5, 10, 20, 40, 50, 100, 200, 300, 400 and 500kGy with a dose rate of 11.22 kGy/s for all doses and rate of 11.22 kGy/s and 22.38 kGy/s for a dose of 20kGy. After the processes of surface modification of polyamide 6.6, part of the untreated samples, treated by plasma and by ionizing radiation were incorporated into the polyacrylic rubber, and another part was designed to characterize the surface using the techniques of SEM / EDS, FT- IR, PIXE / RBS, AFM and contact angle. Untreated samples and the irradiated samples did not join the polyacrylic rubber. The samples treated by plasma joined the polyacrylic rubber efficiently and showed differences in roughness in SEM and AFM, and an increase in contact angle when compared with untreated samples. The irradiated samples showed no significant differences in the analysis of properties used in this study when compared with untreated samples. Ionizing radiation was not effective in surface modification of polyamide 6.6 for adherence with polyacrylic rubber. (author)

  14. Free Radical Scavenging Properties of Annona squamosa

    Science.gov (United States)

    Vikas, Biba; Akhil B, S; P, Remani; Sujathan, K

    2017-10-26

    Annona squamosa has extensively been used in the traditional and folkloric medicine and found to possess many biological activities. Different solvents, petroleum ether, chloroform, ethyl acetate and methanol extracts of Annona squamosa seeds (ASPE, ASCH, ASEA, ASME) have been used to prepare plant extracts. The present investigations dealt with the free radical scavenging activity of four extracts using various techniques such as total reducing power estimation, total phenolic count, 1,1-diphenyl-2-picryl hydrazyl (DPPH) radical scavenging effect, evaluation of ABTS cation decolorisation capacity, FRAP assay, hdroxyl radical scavenging assay, super oxide assay and Nitric oxide radical scavenging assay of the extracts. The results showed that the four extracts of Annona squamosa showed significant reducing power in four extracts. The total phenolic contents in petroleum ether, chloroform, ethyl acetate, methanol extracts and positive control were 0.64±0.17, 0.54±0.27, 0.49±0.24, 0.57±0.22 and 0.66±0.33. The antioxidant capacity by ABTS assay of ASPE, ASCH, ASEA, ASME and positive control, trolox showed 77.75±0.5,73.25±1.7,78.5± 1.2 , 80 ± 0.8 μg/ml and 94.2 ± 0.9 respectively. The (50 % scavenging activity) SA50 of ASPE and ASCH, ASEA and ASME was found to be 34.4 μg/ml, 43.8 μg/ml 34.7 μg/m and 28.8 μg/ml respectively by DPPH assay. The percentage of hydroxyl radical scavenging increased with the increasing concentration of the extracts. ASPE, ASCH, ASEA and ASME showed superoxide radical scavenging activity, as indicated by their values 66 ± 0.5, 68 ± 1 ,63 ± 1 and 70 ± 0.5 μg/ml respectively compared to gallic acid which was 97 ± 0.5 μg/ml. The values for scavenging of nitric oxide for ASPE, ASCH, ASEA and ASME were 91.0 ± 1.0, 66.75 ± 0.5, 71.75 ± 1.1 and 75.75 ± 1.15 μg/ml while value for standard ascorbic acid was 91.0 ± 1.0 μg/ml. The results revealed strong antioxidants in four extracts may lead to the development of potent

  15. Radical-Scavenging Compounds from Olive Tree (Olea europaea L.) wood

    NARCIS (Netherlands)

    Pérez-Bonilla, M.; Salido, S.; Beek, van T.A.; Altarejos, J.

    2014-01-01

    The purpose of this study was to complete knowledge on the chemical composition and radical-scavenging activity of olive tree wood. Two new monoterpene glycosides, (-)-oleuropeic acid 6'-O-a-d-glucopyranosyl ester (6a) and (-)-perillic acid 1'-O-ß-d-primeverosyl ester (8), together with the known

  16. Promoter scanning of the human COX-2 gene with 8-ring polyamides: unexpected weakening of polyamide-DNA binding and selectivity by replacing an internal N-Me-pyrrole with β-alanine.

    Science.gov (United States)

    Bashkin, James K; Aston, Karl; Ramos, Joseph P; Koeller, Kevin J; Nanjunda, Rupesh; He, Gaofei; Dupureur, Cynthia M; David Wilson, W

    2013-02-01

    Rules for polyamide-DNA recognition have proved invaluable for the design of sequence-selective DNA binding agents in cell-free systems. However, these rules are not fully transferrable to predicting activity in cells, tissues or animals, and additional refinements to our understanding of DNA recognition would help biomedical studies. Similar complexities are encountered when using internal β-alanines as polyamide building blocks in place of N-methylpyrrole; β-alanines were introduced in polyamide designs to maintain good hydrogen bonding registry with the target DNA, especially for long polyamides or those with several GC bp (P.B. Dervan, A.R. Urbach, Essays Contemp. Chem. (2001) 327-339). Thus, to clarify important subtleties of molecular recognition, we studied the effects of replacing a single pyrrole with β-alanine in 8-ring polyamides designed against the Ets-1 transcription factor. Replacement of a single internal N-methylpyrrole with β-alanine to generate a β/Im pairing in two 8-ring polyamides causes a decrease in DNA binding affinity by two orders of magnitude and decreases DNA binding selectivity, contrary to expectations based on the literature. Measurements were made by fluorescence spectroscopy, quantitative DNA footprinting and surface plasmon resonance, with these vastly different techniques showing excellent agreement. Furthermore, results were validated for a range of DNA substrates from small hairpins to long dsDNA sequences. Docking studies helped show that β-alanine does not make efficient hydrophobic contacts with the rest of the polyamide or nearby DNA, in contrast to pyrrole. These results help refine design principles and expectations for polyamide-DNA recognition. Copyright © 2012 Elsevier Masson SAS. All rights reserved.

  17. High-performance polyamide thin-film-nanocomposite reverse osmosis membranes containing hydrophobic zeolitic imidazolate framework-8

    KAUST Repository

    Duan, Jintang; Pan, Yichang; Pacheco Oreamuno, Federico; Litwiller, Eric; Lai, Zhiping; Pinnau, Ingo

    2015-01-01

    A hydrophobic, hydrothermally stable metal-organic framework (MOF) - zeolitic imidazolate framework-8 (ZIF-8) was successfully incorporated into the selective polyamide (PA) layer of thin-film nanocomposite (TFN) membranes for water desalination

  18. UV excimer laser and low temperature plasma treatments of polyamide materials

    Science.gov (United States)

    Yip, Yiu Wan Joanne

    Polyamides have found widespread application in various industrial sectors, for example, they are used in apparel, home furnishings and similar uses. However, the requirements for high quality performance products are continually increasing and these promote a variety of surface treatments for polymer modification. UV excimer laser and low temperature plasma treatments are ideally suited for polyamide modification because they can change the physical and chemical properties of the material without affecting its bulk features. This project aimed to study the modification of polyamides by UV excimer laser irradiation and low temperature plasma treatment. The morphological changes in the resulting samples were analysed by scanning electron microscopy (SEM) and tapping mode atomic force microscopy (TM-AFM). The chemical modifications were studied by x-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS) and chemical force microscopy (CFM). Change in degree of crystallinity was examined by differential scanning calorimetry (DSC). After high-fluence laser irradiation, topographical results showed that ripples of micrometer size form on the fibre surface. By contrast, sub-micrometer size structures form on the polyamide surface when the applied laser energy is well below its ablation threshold. After high-fluence laser irradiation, chemical studies showed that the surface oxygen content of polyamide is reduced. A reverse result is obtained with low-fluence treatment. The DSC result showed no significant change in degree of crystallinity in either high-fluence or low-fluence treated samples. The same modifications in polyamide surfaces were studied after low temperature plasma treatment with oxygen, argon or tetrafluoromethane gas. The most significant result was that the surface oxygen content of polyamide increased after oxygen and argon plasma treatments. Both treatments induced many hydroxyl (-OH) and carboxylic acid (-COOH

  19. Nature or Nurture? Gender Roles Scavenger Hunt

    Science.gov (United States)

    Whalen, Shannon; Maurer-Starks, Suanne

    2008-01-01

    The examination of gender roles and stereotypes and their subsequent impact on sexual behavior is a concept for discussion in many sex education courses in college and sex education units in high school. This analysis often leads to a discussion of the impact of nature vs. nurture on gender roles. The gender roles scavenger hunt is an interactive…

  20. Role of antioxidant scavenging enzymes and extracellular ...

    African Journals Online (AJOL)

    In the present work, we studied the role of antioxidant scavenging enzymes of plant pathogenic bacteria: catalase, ascorbate peroxidase and a virulence factor; extracelluar polysaccharide production in determining the virulence of Xanthomonas oryzae pv. oryzae (Xoo) isolates and its differential reaction to rice cultivars.

  1. Antioxidant Capacity, Radical Scavenging Kinetics and Phenolic ...

    African Journals Online (AJOL)

    Antioxidant Capacity, Radical Scavenging Kinetics and Phenolic Profile of Methanol Extracts of Wild Plants of Southern Sonora, Mexico. EF Moran-Palacio, LA Zamora-Álvarez, NA Stephens-Camacho, GA Yáñez- Farías, A Virgen-Ortiz, O Martínez-Cruz, JA Rosas-Rodríguez ...

  2. Phytochemical screening, free radical scavenging and antibacterial ...

    African Journals Online (AJOL)

    Cassia sieberiana is a tropical plant, widely distributed throughout Sudan and Guinea savannah. It is used in traditional medicine for the treatment of malarial, cancer and stomach ache. The study was conducted to screen for phytochemicals, free radical scavenging and antibacterial potentials of the root bark.

  3. Scavenging of particulate elemental carbon into stratus cloud

    Energy Technology Data Exchange (ETDEWEB)

    Kaneyasu, Naoki; Maeda, Takahisa [National Inst. for Resources and Environment, Tsukuba (Japan)

    1995-12-31

    The role of atmospheric aerosols on the alternation of cloud radiative properties has widely been recognized since 1977 when Tomey and his coworkers have numerically demonstrated the effect of increased cloud condensation nuclei (CCN). At the same time, cloud processes are one of the most important factor in controlling the residence time of atmospheric aerosols through the wet removal process. The redistribution of the size and the composition of pre-cloud aerosols is also the important role of cloud process on the nature of atmospheric aerosols. In order to study these cloud-aerosol interaction phenomena, the incorporation of aerosols into cloud droplets is the first mechanism to be investigated. Among the several mechanisms for the incorporation of aerosols into cloud droplets, nucleation scavenging, is the potentially important process in the view of cloud-aerosol interactions. This critical supersaturation for a given radius of a particle can be theoretically calculated only for pure species, e.g., NaCl. However, a significant portion of the atmospheric aerosols is in the form of internal mixture of multiple components, such as SO{sub 4}{sup 2-}, NO{sub 3}{sup -}, NH{sub 4}{sup +} and particulate elemental carbon. The knowledge acquired by field measurements is therefore essential on this subject. The present study focuses on the scavenging of major components of urban atmospheric aerosols, in particular the incorporation of particulate elemental carbon into stratus cloud. Particulate elemental carbon is the strongest light absorbing species in visible region, and has potential to change the optical property of cloud. On the basis of the measurements conducted at a mountain located in the suburb of Tokyo Metropolitan area, Japan, some insights on the scavenging of particulate elemental carbon into cloud droplet will be presented

  4. Scavenging of particulate elemental carbon into stratus cloud

    Energy Technology Data Exchange (ETDEWEB)

    Kaneyasu, Naoki; Maeda, Takahisa [National Inst. for Resources and Environment, Tsukuba (Japan)

    1996-12-31

    The role of atmospheric aerosols on the alternation of cloud radiative properties has widely been recognized since 1977 when Tomey and his coworkers have numerically demonstrated the effect of increased cloud condensation nuclei (CCN). At the same time, cloud processes are one of the most important factor in controlling the residence time of atmospheric aerosols through the wet removal process. The redistribution of the size and the composition of pre-cloud aerosols is also the important role of cloud process on the nature of atmospheric aerosols. In order to study these cloud-aerosol interaction phenomena, the incorporation of aerosols into cloud droplets is the first mechanism to be investigated. Among the several mechanisms for the incorporation of aerosols into cloud droplets, nucleation scavenging, is the potentially important process in the view of cloud-aerosol interactions. This critical supersaturation for a given radius of a particle can be theoretically calculated only for pure species, e.g., NaCl. However, a significant portion of the atmospheric aerosols is in the form of internal mixture of multiple components, such as SO{sub 4}{sup 2-}, NO{sub 3}{sup -}, NH{sub 4}{sup +} and particulate elemental carbon. The knowledge acquired by field measurements is therefore essential on this subject. The present study focuses on the scavenging of major components of urban atmospheric aerosols, in particular the incorporation of particulate elemental carbon into stratus cloud. Particulate elemental carbon is the strongest light absorbing species in visible region, and has potential to change the optical property of cloud. On the basis of the measurements conducted at a mountain located in the suburb of Tokyo Metropolitan area, Japan, some insights on the scavenging of particulate elemental carbon into cloud droplet will be presented

  5. Preparation and Characterization of Polyurethane-Polydimethylsiloxane/Polyamide12-b-Polytetramethylene Glycol Blend Membranes for Gas Separation

    Directory of Open Access Journals (Sweden)

    Mohammad Ali Semsarzadeh*

    2013-07-01

    Full Text Available Blend membranes of synthesized polyurethane based on toluene diisocyanate (TDI, polydimethylsiloxane (PDMS and polytetramethylene glycol (PTMG with polyamide12-b-PTMG were prepared by solution casting technique. The synthesized polyurethane-polydimethylsiloxane and PU-PDMS/polyamide12-b-PTMG blend membranes were characterized by Fourier transform infrared spectroscopy (FTIR, differential scanning calorimetry (DSC and scanning electron microscopy (SEM. In the FTIR spectrum of the synthesized PU-PDMS, the disappearance of NCO stretching vibration at 2270 cm−1 was used to confirm the completion of the reaction. According to our DSC results, the use of higher polyamide12-b-PTMG content in PU-PDMS/polyamide12-b-PTMG blends led to greater compatibility between the two phases. The SEM images showed that the blends with polyamide12-b-PTMG (20 wt% were significantly more homogeneous in the micrometric scale compared to other samples. Gas transport properties have been determined for N2, CO2 and He gases and the obtained permeability values were correlated with the properties of the blends. The comparison of the results with that of the pure PU-PDMS membrane showed that the blend membranes had a higher permeability toward CO2 and lower toward N2 gas. The blend membrane with 20 wt% polyamide12-b-PTMG showed higher CO2 permeability (≈105 Barrer compared to PU-PDMS membrane. By introduction of polyamide12-b-PTMG into PU-PDMS matrix a perceptible rise in helium ideal selectivity of the blend membranes was observed. In blend membranes with 5-20 wt% polyamide12-b-PTMG contents, an enhancement of CO2/N2 (244%, He/N2 (20% and CO2/He (103% selectivity factor was observed. The experimental permeability values of the blend membranes were compared with the calculated permeability based on a modified additive logarithmic model.

  6. Scavenging and recombination kinetics in a radiation spur: The successive ordered scavenging events

    Science.gov (United States)

    Al-Samra, Eyad H.; Green, Nicholas J. B.

    2018-03-01

    This study describes stochastic models to investigate the successive ordered scavenging events in a spur of four radicals, a model system based on a radiation spur. Three simulation models have been developed to obtain the probabilities of the ordered scavenging events: (i) a Monte Carlo random flight (RF) model, (ii) hybrid simulations in which the reaction rate coefficient is used to generate scavenging times for the radicals and (iii) the independent reaction times (IRT) method. The results of these simulations are found to be in agreement with one another. In addition, a detailed master equation treatment is also presented, and used to extract simulated rate coefficients of the ordered scavenging reactions from the RF simulations. These rate coefficients are transient, the rate coefficients obtained for subsequent reactions are effectively equal, and in reasonable agreement with the simple correction for competition effects that has recently been proposed.

  7. Development of oxygen scavenger additives for jet fuels

    Energy Technology Data Exchange (ETDEWEB)

    Beaver, B.D.; Demunshi, R.; Sharief, V.; Tian, D.; Teng, Y. [Duquesne Univ., Pittsburgh, PA (United States)

    1995-05-01

    Our current research program is in response to the US Air Force`s FY93 New Initiative entitled {open_quotes}Advanced Fuel Composition and Use.{close_quotes} The critical goal of this initiative is to develop aircraft fuels which can operate at supercritical conditions. This is a vital objective since future aircraft designs will transfer much higher heat loads into the fuel as compared with current heat loads. In this paper it is argued that the thermal stability of most jet fuels would be dramatically improved by the efficient in flight-removal of a fuel`s dissolved oxygen. It is proposed herein to stabilize the bulk fuel by the addition of an additive which will be judiciously designed and programmed to react with oxygen and produce an innocuous product. It is envisioned that a thermally activated reaction will occur, between the oxygen scavenging additive and dissolved oxygen, in a controlled and directed manner. Consequently formation of insoluble thermal degradation products will be limited. It is believed that successful completion of this project will result in the development of a new type of jet fuel additive which will enable current conventional jet fuels to obtain sufficient thermal stability to function in significantly higher temperature regimes. In addition, it is postulated that the successful development of thermally activated oxygen scavengers will also provide the sub-critical thermal stability necessary for future development of endothermic fuels.

  8. Hybrid joining of polyamide and hydrogenated acrylonitrile butadiene rubber through heat-resistant functional layer of silane coupling agent

    Science.gov (United States)

    Sang, Jing; Sato, Riku; Aisawa, Sumio; Hirahara, Hidetoshi; Mori, Kunio

    2017-08-01

    A simple, direct adhesion method was developed to join polyamide (PA6) to hydrogenated acrylonitrile butadiene rubber (HNBR) by grafting a functional layer of a silane coupling agent on plasma functionalized PA6 surfaces. The functional layer of the silane coupling agent was prepared using a self-assembly method, which greatly improved the heat resistance of PA6 from 153 °C up to 325 °C and the resulting PA6/HNBR joints showed excellent adhesion properties with cohesive failure between PA6 and HNBR. X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and nanoscale infrared microscopy and chemical imaging (Nano-IR, AFM-IR) were employed to characterize the surfaces and interfaces. The Nano-IR analysis method was employed for the first time to analyze the chemical structures of the adhesion interfaces between different materials and to establish the interface formation mechanism. This study is of significant value for interface research and the study of adhesion between resins and rubbers. There is a promising future for heat-resistant functional layers on resin surfaces, with potential application in fuel hose composite materials for the automotive and aeronautical industries.

  9. Fabrication and characterization of drug-loaded nano-hydroxyapatite/polyamide 66 scaffolds modified with carbon nanotubes and silk fibroin

    Directory of Open Access Journals (Sweden)

    Yao MZ

    2016-11-01

    Full Text Available Meng-Zhu Yao,1 Ming-Yi Huang-Fu,1 Hui-Na Liu,1 Xia-Rong Wang,1 Xiaoxia Sheng,2 Jian-Qing Gao1 1Institute of Pharmaceutics, College of Pharmaceutical Sciences, Zhejiang University, 2Hangzhou SoliPharma Co., Ltd, Hangzhou, Zhejiang, People’s Republic of China Abstract: Nano-hydroxyapatite/polyamide 66 (nHA/PA66 porous scaffolds were fabricated by a phase inversion method. Carbon nanotubes (CNTs and silk fibroin (SF were used to modify the surface of the nHA/PA66 scaffolds by freeze-drying and cross-linking. Dexamethasone was absorbed to the CNTs to promote the osteogenic differentiation of bone mesenchymal stem cells (BMSCs. The cell viability of BMSCs was investigated by changing the concentration of the CNT dispersion, and the most biocompatible scaffold was selected. In addition, the morphology and mechanical property of the scaffolds were investigated. The results showed that the nHA/PA66 scaffolds modified with CNTs and SF met the requirements of bone tissue engineering scaffolds. The dexamethasone-loaded CNT/SF-nHA/PA66 composite scaffold promoted the osteogenic differentiation of BMSCs, and the drug-loaded scaffolds are expected to function as effective bone tissue engineering scaffolds. Keywords: BMSCs, tissue engineering, porous scaffold, carbon nanotubes, silk fibroin, surface modification, dexamethasone

  10. Water Diffusion Mechanism in Carbon Nanotube and Polyamide Nanocomposite Reverse Osmosis Membranes: A Possible Percolation-Hopping Mechanism

    Science.gov (United States)

    Araki, Takumi; Cruz-Silva, Rodolfo; Tejima, Syogo; Ortiz-Medina, Josue; Morelos-Gomez, Aaron; Takeuchi, Kenji; Hayashi, Takuya; Terrones, Mauricio; Endo, Morinobu

    2018-02-01

    This paper is a contribution to the Physical Review Applied collection in memory of Mildred S. Dresselhaus. The mechanism of water diffusion across reverse osmosis nanocomposite membranes made of carbon nanotubes (CNTs) and aromatic polyamide is not completely understood despite its high potential for desalination applications. While most of the groups have proposed that superflow inside the CNT might positively impact the water flow across membranes, here we show theoretical evidence that this is not likely the case in composite membranes because CNTs are usually oriented parallel to the membrane surface, not to mention that sometimes the nanotube cores are occluded. Instead, we propose an oriented diffusion mechanism that explains the high water permeation by decreasing the diffusion path of water molecules across the membranes, even in the presence of CNTs that behave as impermeable objects. Finally, we provide a comprehensive description of the molecular dynamics occurring in water desalination membranes by considering the bond polarizability caused by dynamic charge transfer and explore the use of molecular-dynamics-derived stochastic diffusion simulations. The proposed water diffusion mechanism offers an alternative and most likely explanation for the high permeation phenomena observed in CNTs and PA nanocomposite membranes, and its understanding can be helpful to design the next generation of reverse osmosis desalination membranes.

  11. The improvement of mechanical and thermal properties of polyamide 12 3D printed parts by fused deposition modelling

    Directory of Open Access Journals (Sweden)

    T. N. A. T. Rahim

    2017-12-01

    Full Text Available This paper addresses the utilisation of fused deposition modelling (FDM technology using polyamide 12, incorporated with bioceramic fillers (i.e. zirconia and hydroxyapatite as a candidate for biomedical applications. The entire production process of printed PA12 is described, starting with compounding, filament wire fabrication and finally, FDM printing. The potential to process PA12 using this technique and mechanical, thermal and morphological properties were also examined. Commonly, a reduction of mechanical properties of printed parts would occur in comparison with injection moulded parts despite using the same material. Therefore, the mechanical properties of the samples prepared by injection moulding were also measured and applied as a benchmark to examine the effect of different processing methods. The results indicated that the addition of fillers improved or maintained the strength and stiffness of neat PA12, at the expense of reduced toughness and flexibility. Melting behaviours of PA12 were virtually insensitive to the processing techniques and were dependent on additional fillers and the cooling rate. Incorporation of fillers slightly lowered the melting temperature, however improved the thermal stability. In summary, PA12 composites were found to perform well with FDM technique and enabling the production of medical implants with acceptable mechanical performances for non-load bearing applications.

  12. Study on the surface chemical properties of UV excimer laser irradiated polyamide by XPS, ToF-SIMS and CFM

    International Nuclear Information System (INIS)

    Yip, Joanne; Chan, Kwong; Sin, Kwan Moon; Lau, Kai Shui

    2002-01-01

    Polyamide (nylon 6) was irradiated by a pulsed ultraviolet (UV) excimer laser with a fluence below its ablation threshold. Chemical modifications on laser treated nylon were studied by X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (Tof-SIMS) and chemical force microscopy (CFM). XPS study provides information about changes in chemical composition and the chemical-state of atom types on the fiber surface. The high sensitivity of ToF-SIMS to the topmost layers was used to detect crosslinking after the laser treatment. Gold-coated AFM tips modified with -COOH terminated self-assembled alkanethiol monolayers (SAMs) were used to measure adhesion forces on the untreated and laser treated samples. XPS results revealed that the irradiated samples have higher oxygen content than prior to laser irradiation. Tof-SIMS analysis illustrated that carbonyl groups in nylon 6 decrease significantly but hydroxyl groups increase after low-fluence laser irradiation. The adhesion force measurements by CFM showed spatial distribution of hydroxyl groups on nylon 6 after the laser treatment

  13. Thin porphyrin composite membranes with enhanced organic solvent transport

    KAUST Repository

    Phuoc, Duong

    2018-05-01

    Extending the stability of polymeric membranes in organic solvents is important for applications in chemical and pharmaceutical industry. Thin-film composite membranes with enhanced solvent permeance are proposed, using porphyrin as a building block. Hybrid polyamide films are formed by interfacial polymerization of 5,10,15,20-(tetra-4-aminophenyl)porphyrin/m-phenylene diamine (MPD) mixtures with trimesoyl chloride. Porphyrin is a non-planar molecule, containing a heterocyclic tetrapyrrole unit. Its incorporation into a polyamide film leads to higher free volume than that of a standard polyamide film. Polyamide films derived from porphyrin and MPD amines with a fixed total amine concentration of 1wt% and various porphyrin/MPD ratios were fabricated and characterized. The porphyrin/MPD polyamide film was complexed with Cu(II), due to the binding capacity of porphyrin to metal ions. By coupling scanning transmission electron microscopy (STEM) with electron energy-loss spectroscopy (EELS), Cu mapping was obtained, revealing the distribution of porphyrin in the interfacial polymerized layer. By using porphyrin as amine-functionalized monomer a membrane with thin selective skin and enhanced solvent transport is obtained, with good dye selectivity in the nanofiltration range. For instance, an ultra-fast hexane permeance, 40-fold increased, was confirmed when using 0.5/0.5 porphyrin/MPD mixtures, instead of only MPD as amine monomer. A rejection of 94.2% Brilliant Blue R (826g/mol) in methanol was measured.

  14. Investigation into Seasonal Scavenging Patterns of Raccoons on Human Decomposition.

    Science.gov (United States)

    Jeong, Yangseung; Jantz, Lee Meadows; Smith, Jake

    2016-03-01

    Although raccoons are known as one of the most common scavengers in the U.S., scavenging by these animals has seldom been studied in terms of forensic significance. In this research, the seasonal pattern of raccoon scavenging and its effect on human decomposition was investigated using 178 human cadavers placed at the Anthropological Research Facility (ARF) of the University of Tennessee, Knoxville (UTK) between February 2011 and December 2013. The results reveal that (i) the frequency of scavenging increases during summer, (ii) scavenging occurs relatively immediately and lasts shorter in summer months, and (iii) scavenging influences the decomposition process by hollowing limbs and by disturbing insect activities, both of which eventually increases the chance of mummification on the affected body. This information is expected to help forensic investigators identify raccoon scavenging as well as make a more precise interpretation of the effect of raccoon scavenging on bodies at crime scenes. © 2015 American Academy of Forensic Sciences.

  15. Composites

    International Nuclear Information System (INIS)

    Kasen, M.B.

    1983-01-01

    This chapter discusses the roles of composite laminates and aggregates in cryogenic technology. Filamentary-reinforced composites are emphasized because they are the most widely used composite materials. Topics considered include composite systems and terminology, design and fabrication, composite failure, high-pressure reinforced plastic laminates, low-pressure reinforced plastics, reinforced metals, selectively reinforced structures, the effect of cryogenic temperatures, woven-fabric and random-mat composites, uniaxial fiber-reinforced composites, composite joints in cryogenic structures, joining techniques at room temperature, radiation effects, testing laminates at cryogenic temperatures, static and cyclic tensile testing, static and cyclic compression testing, interlaminar shear testing, secondary property tests, and concrete aggregates. It is suggested that cryogenic composite technology would benefit from the development of a fracture mechanics model for predicting the fitness-for-purpose of polymer-matrix composite structures

  16. Preparation and characterization of new polyamide/montmorillonite nanocomposites containing azo moiety in the main chain

    Directory of Open Access Journals (Sweden)

    Khalil Faghihi

    2016-11-01

    Full Text Available Two new samples of polyamide/montmorillonite reinforced nanocomposites containing 4,4′-azobenzoic acid moiety in the main chain were synthesized by a convenient solution intercalation technique. Polyamide (PA 4 as a source of polymer matrix was synthesized by the direct polycondensation reaction of 4,4′-azobenzoic acid 2 with 4,4′-diamino diphenyl ether 3 in the presence of triphenyl phosphite (TPP, CaCl2, pyridine and N-methyl-2-pyrrolidone (NMP. Morphology and structure of the resulting PA-nanocomposite films 4a and 4b with 10 and 20% silicate particles were characterized by FTIR spectroscopy, X-ray diffraction (XRD and scanning electron microscopy (SEM. The effect of clay dispersion and the interaction between clay and polymeric chains on the properties of nanocomposites films were investigated by using UV–vis spectroscopy, thermogravimetric analysis (TGA and water uptake measurements.

  17. Enhancing the cellular uptake of Py–Im polyamides through next-generation aryl turns

    OpenAIRE

    Meier, Jordan L.; Montgomery, David C.; Dervan, Peter B.

    2012-01-01

    Pyrrole–imidazole (Py–Im) hairpin polyamides are a class of programmable, sequence-specific DNA binding oligomers capable of disrupting protein–DNA interactions and modulating gene expression in living cells. Methods to control the cellular uptake and nuclear localization of these compounds are essential to their application as molecular probes or therapeutic agents. Here, we explore modifications of the hairpin γ-aminobutyric acid turn unit as a means to enhance cellular uptake and biologica...

  18. Study of the effect of ionizing radiation on properties of polyamide 6 with fibreglass reinforcement

    International Nuclear Information System (INIS)

    Pinto, Clovis

    2007-01-01

    It is each time more common the use of polymers reinforced with fibreglass in the domestic market. Between them it is used polyamide 6 that it presents good tension resistance, to the impact and the humidity absorption compared with non-reinforced, being also at the present time used in the automobile industry in parts underneath the hood, especially in the radiator frames. The aim of this work is to study the effect of ionizing radiation on properties of polyamide 6 with fibreglass reinforcement, undergone to different radiation doses. Samples were prepared and irradiated on JOB 188 accelerator with an electron beam energy of 1.5 MeV in air with different doses (100 to 600 kGy) and a dose rate of 22.61 kGy/h. Afterward the irradiation, the properties of the samples of irradiated polyamide 6 with fibreglass reinforcement were evaluated and compared with the samples non-irradiated. It evidenced that the mechanical properties flexural resistance and tension resistance increased and the resistance to the impact decreased. Regarding the thermal properties of the temperature of fusing decreased of 224,4 deg C for 212,5 deg C but the loss of mass ahead of the constant increase of the temperature also decreased. In the property of resistance to the glow wire the polyamide 6 with fibreglass reinforcement had a good performance. The images caught for Scanning Electronic Microscopy show that the irradiation provoked a good integration enters the fibreglass and polymer what was responsible for the good performance in the property of resistance to the glow wire. (author)

  19. Study of nanocomposites prepared from polyamides and biodegradable polyesters and poly(ester amide)s

    OpenAIRE

    Morales Gámez, Laura Teresa

    2012-01-01

    Premi extraordinari doctorat curs 2011-2012, àmbit d’Enginyeria Industrial Polymer clay nanocomposites of polyamides and biodegradable polymers with three kinds of organomodified clays were prepared by different techniques (in situ polymerization, solution casting, and melt mixing). The polymers used in this research were nylons 56, 65 and 47 and the biodegradable polymers: poly (glycolic acid-alt-6-hydrohexanoic acid) and poly(glycolic acid-alt-6-aminohexanoic acid). The developmen...

  20. An electron beam irradiation method for modification of surface electrical resistivity of polyamides

    International Nuclear Information System (INIS)

    Brasoveanu, M. M.; Timus, D.; Nemtanu, M. R.

    2002-01-01

    The synthetic textiles which have mechanical and processing properties and a low price are very useful and consequently in high demand. The low antistatic qualities are an important disadvantage, but not impossible to eliminate. The aim of paper is the study of modification the antistatic properties of polyamide by grafting of monomers by irradiation. Twisted and unthermofixed polyamide-6 fibre from CFS Savinesti were investigated. The samples of polyamide were irradiated with an electron beam from the ALIN-7 linear accelerator of Electron Accelerators Laboratory of National Institute for Lasers, Plasma and Radiation Physics, Bucharest. Immediately after irradiation, the samples were measured by electron spin resonance (ESR). ESR spectra were recorded at room temperature using a Jeol spectrometer, JES-ME-3X, with 100 kHz modulation. In polyamide-6 at least two irradiation defect types occurred which present EPR signal by electron beam irradiation. Unstable centres of type A presenting an incompletely resolved hyperfine structure can be attributed to radicals -N-CH 2 - or -NH-CH-CH 2 -. Both radicals can present at room temperature a five-line spectrum like the radical formed in this work. First radical appears with very low probability and if the free bond is at one of carbon atoms then it will be stabilized immediately in a position from nitrogen. These type A radicals can appear in same zone and then they can react and form unsaturated bonds or bridge between the polymeric chains. Thus, it will appear the type B defects which were more stabile and without structure. On these double chains one can graft vinylic monomers even after time intervals longer from irradiation. (authors)

  1. Reuse of effluent from dyeing process of polyamide fibers modified by double barrier discharge (DBD) plasma

    OpenAIRE

    Oliveira, Fernando Ribeiro; Steffens, F.; Souto, A. Pedro; Zille, Andrea

    2016-01-01

    Published online: 27 Feb 2015 Low-temperature plasma technology becomes more and more attractive compared with traditional wet processes in textile preparation and finishing due to its high efficiency and low environmental impact. The objective of this study was to investigate the influence of dielectric barrier discharge plasma treatment on the trichromic dyeing process of polyamide 6.6 (PA66) and the reuse of the generated effluents for new dyeing processes. Chemical and physical charact...

  2. Chemical and structural changes in polyamide based organic–inorganic hybrid materials upon incorporation of SeS{sub 2}O{sub 6}{sup 2−} precursor

    Energy Technology Data Exchange (ETDEWEB)

    Krylova, V.; Dukstienė, N.; Žalenkienė, S. [Department of Physical and Inorganic Chemistry, Kaunas University of Technology, Radvilenu st. " 1" 9" , LT-50254, Kaunas (Lithuania); Baltrusaitis, J., E-mail: job314@lehigh.edu [Department of Chemical and Biomolecular Engineering, Lehigh University, B336 Iacocca Hall, 111 Research Drive, Bethlehem, PA 18015 (United States)

    2017-01-15

    Highlights: • We investigated deposited and diffused K{sub 2}SeS{sub 2}O{sub 6} into polyamide 6 (PA 6). • AAS showed Se:S molar ratio = 1:2 within the PA. • Various decomposition products were detected within the polymer. • Measured bandgap shifted towards lower light absorption energies. - Abstract: Composite organic-inorganic functional materials are of significant importance in various applications of science and technology. In this work, physicochemical characterization of such composite materials obtained after the exposure of polyamide PA 6 to K{sub 2}SeS{sub 2}O{sub 6} precursor solution was performed. Chalcogenized polymer surface was characterized using X-ray diffraction, infrared, and UV–vis spectroscopies while their bulk chemical analysis was performed using atomic absorption spectroscopy. Crystallite size was not found to change with the exposure to K{sub 2}SeS{sub 2}O{sub 6} precursor but PA 6 chain–chain separation decreased. Importantly, infrared and X-ray analyses showed chemical bonding taking place between the PA 6 and SeS{sub 2}O{sub 6}{sup 2−} ions via −NH− functional group. A distinct change in bandgap, E{sub g}, value was observed in UV–vis spectra due to the presence of SeS{sub 2}O{sub 6}{sup 2−}, SeSO{sub 3}{sup 2−} and Se{sub 2}S{sub 2}O{sub 6}{sup 2−} ions formed via decomposition of the precursor material in acidic medium. After extended 4 h chalcogenation a distinct absorption due to the elemental selenium was also observed as obtained from Tauc plots.

  3. Precipitation scavenging of tritiated water vapour (HTO)

    International Nuclear Information System (INIS)

    Ogram, G.L.

    1985-10-01

    Precipitation scavenging (or washout) is an important mechanism for the removal of HTO from the atmosphere. Methods of parameterizing the depletion of a plume of HTO released to the atmosphere are examined. Simple approaches, commonly used for atmospheric transport modelling purposes, such as the use of a constant washout coefficient or washout ratio, or the use of parameters based on equilibrium assumptions, are often not justified. It is shown that these parameters depend strongly on ambient temperature and plume dimensions, as well as rainfall rate. An approximate expression for washout ratio, as a function of these variables, is developed, and it is shown that near equilibrium washout conditions are only expected to hold at long plume travel distances. A possible method of treating scavenging by snow is also suggested

  4. Mobile vapor recovery and vapor scavenging unit

    International Nuclear Information System (INIS)

    Stokes, C.A.; Steppe, D.E.

    1991-01-01

    This patent describes a mobile anti- pollution apparatus, for the recovery of hydrocarbon emissions. It comprises a mobile platform upon which is mounted a vapor recovery unit for recovering vapors including light hydrocarbons, the vapor recovery unit having an inlet and an outlet end, the inlet end adapted for coupling to an external source of hydrocarbon vapor emissions to recover a portion of the vapors including light hydrocarbons emitted therefrom, and the outlet end adapted for connection to a means for conveying unrecovered vapors to a vapor scavenging unit, the vapor scavenging unit comprising an internal combustion engine adapted for utilizing light hydrocarbon in the unrecovered vapors exiting from the vapor recovery unit as supplemental fuel

  5. Study of the ionizing radiation effect on the polyamide 6,6 mechanical properties

    International Nuclear Information System (INIS)

    Colombo, Maria Aparecida da Silva

    2004-01-01

    Polyamide 6,6 due to its excellent mechanical, thermal and electrical properties and its great performance in multiple industrial applications is considered one of the most important engineering polymers. However, in specific applications, some of its properties need to be improved by means additives or fillers to reach the required properties increasing its final cost. By these considerations, the aim of this work was to apply the ionizing radiation to improve the natural mechanical properties of polyamide 6,6. Also, to evaluate the irradiation parameters, and the mechanical performance of the irradiated polymer in order to use the cross-linking, induced by ionizing radiation, as substitute of additives and fillers. Row polyamide 6,6 samples, for mechanical tests, were prepared by injection molded and then irradiated with high energetic electrons to reach doses of 70, 100, 150, and 200 kGy. The mechanical performance, of non-irradiated and irradiated samples, was evaluated by tensile strength, impact, hardness and wear measurements. Furthermore, hardness and wear tests were carried out with samples, which were immersed in petroleum and sea water for 6 months. The experimental results have shown that, in the studied dose range, the tensile strength increases 25%, the hardness Shore D 15%, the impact values diminished by 80% and the wear values decreased 20 times between 0 and 200 kGy. The effect of the petroleum and sea water were shown mainly in the nonirradiated samples. (author)

  6. Proton Conductive Channel Optimization in Methanol Resistive Hybrid Hyperbranched Polyamide Proton Exchange Membrane

    Directory of Open Access Journals (Sweden)

    Liying Ma

    2017-12-01

    Full Text Available Based on a previously developed polyamide proton conductive macromolecule, the nano-scale structure of the self-assembled proton conductive channels (PCCs is adjusted via enlarging the nano-scale pore size within the macromolecules. Hyperbranched polyamide macromolecules with different size are synthesized from different monomers to tune the nano-scale pore size within the macromolecules, and a series of hybrid membranes are prepared from these two micromoles to optimize the PCC structure in the proton exchange membrane. The optimized membrane exhibits methanol permeability low to 2.2 × 10−7 cm2/s, while the proton conductivity of the hybrid membrane can reach 0.25 S/cm at 80 °C, which was much higher than the value of the Nafion 117 membrane (0.192 S/cm. By considering the mechanical, dimensional, and the thermal properties, the hybrid hyperbranched polyamide proton exchange membrane (PEM exhibits promising application potential in direct methanol fuel cells (DMFC.

  7. Immobilization of nanoparticle titanium dioxide membrane on polyamide fabric by low temperature hydrothermal method

    International Nuclear Information System (INIS)

    Zhang Hui; Yang Lu

    2012-01-01

    A thin layer of nanoparticle titanium dioxide was immobilized on polyamide 6 (PA6) fiber using titanium sulfate and urea at low temperature hydrothermal condition. The titanium dioxide loaded fabric was characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, differential scanning calorimetry and thermal gravimetry techniques. The optical and mechanical properties, water absorption and degradation of methylene blue dye under ultraviolet (UV) irradiation of the PA6 fabric before and after treatments were also examined. It was found that when PA6 fabric was treated in titanium sulfate and urea aqueous solution, anatase nanocrystalline titanium dioxide was synthesized and simultaneously adhered onto the fiber surface. The average crystal size of titanium dioxide nanoparticles was about 13.2 nm. The thermal behavior of PA6 fiber distinctly changed and the onset decomposition temperature decreased. As compared with the untreated fabric, the protection against UV radiation was improved. The water absorbency increased slightly. As the fabric dimensions were reduced in warp and weft directions, the breaking load and tensile strain increased to some extent. The titanium dioxide coated fabric could degradate methylene blue dye under UV irradiation. - Highlights: ► We employed a method to immobilize TiO 2 nanoparticle on polyamide fiber. ► We fabricated the TiO 2 -coated polyamide fabric with the photocatalytic activity. ► The modification method may be suitable for the potential applications.

  8. Scavenger Receptors and Resistance to Inhaled Allergens

    Science.gov (United States)

    2010-02-01

    throughput manner which will enable future studies. We plan to continue two especially interesting aspects of these studies. First, the epigenetic control...directs mod- ified proteins to antigen presentation. Eur. J. Immunol. 29: 512–521. 30. Granucci, F., F. Petralia, M. Urbano , S. Citterio, F. Di Tota, L...11 Suppl:S32-6. 50. Granucci F, Petralia F, Urbano M, Citterio S, Di Tota F, Santambrogio L, Ricciardi-Castagnoli P: The scavenger receptor MARCO

  9. Tribological performance of polymer composites used in electrical ...

    Indian Academy of Sciences (India)

    engineering applications. ZAFER DEMIR. Anadolu University, Eskisehir, Turkey. MS received 28 December 2011; revised 13 March 2012. Abstract. Sliding wear performance of 20% mica-filled polyamide 6 (PA6 + 20% mica) and 20% short glass fibre- reinforced polysulphone (PSU + 20 GFR) polymer composites used in ...

  10. Thermoplastic Composite Wind Turbine Blades : An Integrated Design Approach

    NARCIS (Netherlands)

    Joncas, S.

    2010-01-01

    This thesis proposes a new structural design concept for future large wind turbine blades based on fully recyclable thermoplastic composites (TPC). With respect to material properties, cost and processing, reactively processed anionic polyamide-6 (APA-6) has been identified as the most promising

  11. Energy scavenging sources for biomedical sensors

    International Nuclear Information System (INIS)

    Romero, E; Warrington, R O; Neuman, M R

    2009-01-01

    Energy scavenging has increasingly become an interesting option for powering electronic devices because of the almost infinite lifetime and the non-dependence on fuels for energy generation. Moreover, the rise of wireless technologies promises new applications in medical monitoring systems, but these still face limitations due to battery lifetime and size. A trade-off of these two factors has typically governed the size, useful life and capabilities of an autonomous system. Energy generation from sources such as motion, light and temperature gradients has been established as commercially viable alternatives to batteries for human-powered flashlights, solar calculators, radio receivers and thermal-powered wristwatches, among others. Research on energy harvesting from human activities has also addressed the feasibility of powering wearable or implantable systems. Biomedical sensors can take advantage of human-based activities as the energy source for energy scavengers. This review describes the state of the art of energy scavenging technologies for powering sensors and instrumentation of physiological variables. After a short description of the human power and the energy generation limits, the different transduction mechanisms, recent developments and challenges faced are reviewed and discussed. (topical review)

  12. Allosteric analysis of glucocorticoid receptor-DNA interface induced by cyclic Py-Im polyamide: a molecular dynamics simulation study.

    Directory of Open Access Journals (Sweden)

    Yaru Wang

    Full Text Available BACKGROUND: It has been extensively developed in recent years that cell-permeable small molecules, such as polyamide, can be programmed to disrupt transcription factor-DNA interfaces and can silence aberrant gene expression. For example, cyclic pyrrole-imidazole polyamide that competes with glucocorticoid receptor (GR for binding to glucocorticoid response elements could be expected to affect the DNA dependent binding by interfering with the protein-DNA interface. However, how such small molecules affect the transcription factor-DNA interfaces and gene regulatory pathways through DNA structure distortion is not fully understood so far. METHODOLOGY/PRINCIPAL FINDINGS: In the present work, we have constructed some models, especially the ternary model of polyamides+DNA+GR DNA-binding domain (GRDBD dimer, and carried out molecular dynamics simulations and free energy calculations for them to address how polyamide molecules disrupt the GRDBD and DNA interface when polyamide and protein bind at the same sites on opposite grooves of DNA. CONCLUSIONS/SIGNIFICANCE: We found that the cyclic polyamide binding in minor groove of DNA can induce a large structural perturbation of DNA, i.e. a >4 Å widening of the DNA minor groove and a compression of the major groove by more than 4 Å as compared with the DNA molecule in the GRDBD dimer+DNA complex. Further investigations for the ternary system of polyamides+DNA+GRDBD dimer and the binary system of allosteric DNA+GRDBD dimer revealed that the compression of DNA major groove surface causes GRDBD to move away from the DNA major groove with the initial average distance of ∼4 Å to the final average distance of ∼10 Å during 40 ns simulation course. Therefore, this study straightforward explores how small molecule targeting specific sites in the DNA minor groove disrupts the transcription factor-DNA interface in DNA major groove, and consequently modulates gene expression.

  13. Polyamide desalination membrane characterization and surface modification to enhance fouling resistance.

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Mukul M. (Univeristy of Texas at Austin, Austin, TX); Freeman, Benny D. (Univeristy of Texas at Austin, Austin, TX); Van Wagner, Elizabeth M. (Univeristy of Texas at Austin, Austin, TX); Hickner, Michael A. (Pennsylvania State University, University Park, PA); Altman, Susan Jeanne

    2010-08-01

    The market for polyamide desalination membranes is expected to continue to grow during the coming decades. Purification of alternative water sources will also be necessary to meet growing water demands. Purification of produced water, a byproduct of oil and gas production, is of interest due to its dual potential to provide water for beneficial use as well as to reduce wastewater disposal costs. However, current polyamide membranes are prone to fouling, which decreases water flux and shortens membrane lifetime. This research explored surface modification using poly(ethylene glycol) diglycidyl ether (PEGDE) to improve the fouling resistance of commercial polyamide membranes. Characterization of commercial polyamide membrane performance was a necessary first step before undertaking surface modification studies. Membrane performance was found to be sensitive to crossflow testing conditions. Concentration polarization and feed pH strongly influenced NaCl rejection, and the use of continuous feed filtration led to higher water flux and lower NaCl rejection than was observed for similar tests performed using unfiltered feed. Two commercial polyamide membranes, including one reverse osmosis and one nanofiltration membrane, were modified by grafting PEGDE to their surfaces. Two different PEG molecular weights (200 and 1000) and treatment concentrations (1% (w/w) and 15% (w/w)) were studied. Water flux decreased and NaCl rejection increased with PEGDE graft density ({micro}g/cm{sup 2}), although the largest changes were observed for low PEGDE graft densities. Surface properties including hydrophilicity, roughness and charge were minimally affected by surface modification. The fouling resistance of modified and unmodified membranes was compared in crossflow filtration studies using model foulant solutions consisting of either a charged surfactant or an oil in water emulsion containing n-decane and a charged surfactant. Several PEGDE-modified membranes demonstrated improved

  14. Composition

    DEFF Research Database (Denmark)

    Bergstrøm-Nielsen, Carl

    2011-01-01

    Strategies are open compositions to be realised by improvising musicians. See more about my composition practise in the entry "Composition - General Introduction". Caution: streaming the sound files will in some cases only provide a few minutes' sample. Please DOWNLOAD them to hear them in full...

  15. Composition

    DEFF Research Database (Denmark)

    2014-01-01

    Memory Pieces are open compositions to be realised solo by an improvising musicians. See more about my composition practise in the entry "Composition - General Introduction". Caution: streaming the sound files will in some cases only provide a few minutes' sample. Please DOWNLOAD them to hear them...

  16. The Effect of Drawing Ratio on Mechanical Property of Nano-Hybrid Polyimide Composite Films

    OpenAIRE

    CHEN Hao; YANG Rui-xiao; WU Chuan-gang; FAN Yong

    2017-01-01

    In order to investigate the impact of drawing ratio of inorganic nano-hybrid polyamide three-layer composite films,the stretched composite films with different draw ratio were prepared by drawing partial imido polyamide film and then through the ring closing reaction in the high temperature,and the draw ratio was 0% ,2% , 4% ,6% ,8% ,10% ,12% ,14% etc. Under the same conditions,we made different draw ratio of three-layer composite film tensile test with the electronic universal material testi...

  17. Radiation polymerizable compositions

    International Nuclear Information System (INIS)

    Goff, D.L.; Yuan, E.L.; Proskow, S.

    1982-01-01

    A polyamide ester resin containing photopolymerizable groups is made more rapidly photopolymerizable and therefore more suitable for forming relief structures on electrical devices (such as capacitors, integrated circuits and semiconductors) by including therein a solvent, a radiation-sensitive polymerizable polyfunctional acrylate compound and an aromatic biimidazole photopolymerization initiator. On exposure through a pattern of a dried film obtained using a solution of such composition, photopolymerization takes place rapidly and efficiently following which developing can be effected and the photopolymerized material baked to leave a heat-resistant polyimide structure. (author)

  18. The effect of gamma irradiation in air and inert atmosphere on structure and properties of unfilled or glass fibre-reinforced polyamide 6

    Czech Academy of Sciences Publication Activity Database

    Porubská, M.; Babić, D.; Janigová, I.; Šlouf, Miroslav; Jomová, K.; Chodák, I.

    2016-01-01

    Roč. 73, č. 6 (2016), s. 1775-1794 ISSN 0170-0839 Institutional support: RVO:61389013 Keywords : polyamide 6 * glass fibre-reinforced polyamide 6 * gamma beam irradiation Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.430, year: 2016

  19. Isolation and characterisation of in vitro and cellular free radical scavenging peptides from corn peptide fractions.

    Science.gov (United States)

    Wang, Liying; Ding, Long; Wang, Ying; Zhang, Yan; Liu, Jingbo

    2015-02-16

    Corn gluten meal, a corn processing industry by-product, is a good source for the preparation of bioactive peptides due to its special amino acid composition. In the present study, the in vitro and cellular free radical scavenging activities of corn peptide fractions (CPFs) were investigated. Results indicated that CPF1 (molecular weight less than 1 kDa) and CPF2 (molecular weight between 1 and 3 kDa) exhibited good hydroxyl radical, superoxide anion radical and 2,2'-azino-bis (3-ethylbenzothiazoline-6-sulphonicacid) diammonium salt (ABTS) radical scavenging activity and oxygen radical absorbance capacity (ORAC). Meanwhile, the in vitro radical scavenging activity of CPF1 was slightly higher than that of CPF2. Both CPF1 and CPF2 also exhibited significant cytoprotective effects and intracellular reactive oxygen species scavenging activity in Caco-2 cells exposed to hydrogen peroxide (H2O2). The amino acid composition analysis revealed that the CPF were rich in hydrophobic amino acids, which comprised of more than 45% of total amino acids. An antioxidant peptide sequence of Tyr-Phe-Cys-Leu-Thr (YFCLT) was identified from CPF1 using matrix-assisted laser desorption/ionization time-of-flight/time-of-flight mass spectrometry (MALDI TOF/TOF MS). The YFCLT exhibited excellent ABTS radical scavenging activity with a 50% effective concentration (EC50) value of 37.63 µM, which was much lower than that of Trolox. In conclusion, corn gluten meal might be a good source to prepare antioxidant peptides.

  20. A comparison of transmission, reflection and photoacoustic FTIR techniques in the analysis of recycled and irradiated polyamide-6

    International Nuclear Information System (INIS)

    Evora, Maria C.; Goncalez, Odair L.

    2002-01-01

    A comparative study involving transmission, reflection and photoacoustic FTIR techniques is presented with analysis of polyamide-6. The potential and limitations of these methods are investigated by analyzing structural variations that take place at the surface in the bulk in recycled and irradiated polyamide-6 with a 1.5 MeV electron beam with a 500kGY dose, in the presence of O 2 . FTIR techniques appear to be sensitive in detecting small structural changes that occur in recycled and irradiated polyamide-6. The analysis of samples indicated the formation of OH, HOC=O-, - C=O groups. Also, small structural changes were detected which are characterisitic of NH and CN-C=O groups. Transmission techniques show better the structural changes in the bulk, and microscopy-FTIR appears to be more sensitive in detecting what occurs at the sample surface. (author)

  1. Flavonoids: hemisynthesis, reactivity, characterization and free radical scavenging activity.

    Science.gov (United States)

    Es-Safi, Nour-Eddine; Ghidouche, Souhila; Ducrot, Paul Henri

    2007-09-26

    Phenolic compounds form one of the main classes of secondary metabolites. They display a large range of structures and they are responsible for the major organoleptic characteristics of plant-derived-foods and beverages, particularly color and taste properties and they also contribute to the nutritional qualities of fruits and vegetables. Phenolic compounds are also highly unstable compounds which undergo numerous enzymatic and chemical reactions during postharvest food storage and processing thus adding to the complexity of plant polyphenol composition. Among these compounds flavonoids constitute one of the most ubiquitous groups of all plant phenolics. Owing to their importance in food organoleptic properties and in human health, a better understanding of their structures, their reactivity and chemical properties in addition to the mechanisms generating them appears essential to predict and control food quality. The purpose of this work is an overview of our findings concerning the hemisynthesis, the reactivity and the enzymatic oxidation of some flavonoids and shed light on the mechanisms involved in some of these processes and the structures of the resulting products. The free radical scavenging activity of some of the synthesized compounds is also presented and a structure-activity relationship is discussed. The first part of this review concerns the synthesis and structural characterization of modified monomeric flavanols. The use of these compounds as precursor for the preparation of natural and modified dimeric procyanidin derivatives was then explored through different coupling reactions. The full characterization of the synthesized compounds was achieved by concerted use of NMR and ESI-MS techniques. The free radical scavenging activity of some of the synthesized compounds was investigated. The second part of this review concerns the enzymatic oxidation of several flavonols by Trametes versicolor laccase. Most of the major oxidation products have been

  2. Flavonoids: Hemisynthesis, Reactivity, Characterization and Free Radical Scavenging Activity

    Directory of Open Access Journals (Sweden)

    Paul Henri Ducrot

    2007-09-01

    Full Text Available Phenolic compounds form one of the main classes of secondary metabolites. They display a large range of structures and they are responsible for the major organoleptic characteristics of plant-derived-foods and beverages, particularly color and taste properties and they also contribute to the nutritional qualities of fruits and vegetables. Phenolic compounds are also highly unstable compounds which undergo numerous enzymatic and chemical reactions during postharvest food storage and processing thus adding to the complexity of plant polyphenol composition. Among these compounds flavonoids constitute one of the most ubiquitous groups of all plant phenolics. Owing to their importance in food organoleptic properties and in human health, a better understanding of their structures, their reactivity and chemical properties in addition to the mechanisms generating them appears essential to predict and control food quality. The purpose of this work is an overview of our findings concerning the hemisynthesis, the reactivity and the enzymatic oxidation of some flavonoids and shed light on the mechanisms involved in some of these processes and the structures of the resulting products. The free radical scavenging activity of some of the synthesized compounds is also presented and a structure-activity relationship is discussed. The first part of this review concerns the synthesis and structural characterization of modified monomeric flavanols. The use of these compounds as precursor for the preparation of natural and modified dimeric procyanidin derivatives was then explored through different coupling reactions. The full characterization of the synthesized compounds was achieved by concerted use of NMR and ESI-MS techniques. The free radical scavenging activity of some of the synthesized compounds was investigated. The second part of this review concerns the enzymatic oxidation of several flavonols by Trametes versicolor laccase. Most of the major oxidation

  3. Antioxidant and Free Radical Scavenging Capacity of Seed and Shell Essential Oils Extracted from Abrus precatorius (L

    Directory of Open Access Journals (Sweden)

    Sunday O. Okoh

    2014-04-01

    Full Text Available Essential oils from plants have been proven safe as natural antioxidants, and few are already marketed as digestive enhancers as well as in prevention of several degenerative diseases. This study evaluated the antioxidant capacity of seed and shell essential oils of Abrus precatorius (L, a herb used for ethno-medicinal practices in Nigeria. The essential oils were obtained by hydro-distillation. The ability of the oils to act as hydrogen/electrons donor or scavenger of radicals were determined by in-vitro antioxidant assays using 2,2-diphenyl-2-picryl-hydrazyl free radical (DPPH. scavenging; 2,2′-azino-bis(3-ethylbenzthiazoline-6-sulfonic acid (ABTS radical scavenging; lipid peroxide and nitric oxide radicals scavenging assays. The IC50 of the seed and shell oils (2.10 mg/mL and 1.20 mg/mL respectively showed that antioxidant activity is higher than that for the standard drugs (3.20 mg/mL and 3.40 mg/mL for the nitric oxide scavenging assay. The lipid peroxidation radical activity of the oils were similar to vitamin C, weak DPPH and ABTS radical scavenging activities were discovered in comparison to vitamin C and rutin. Generally, in the four antioxidant assays, a significant correlation existed between concentrations of the oils and percentage inhibition of free radicals and lipid peroxidation. The composition of A. precatorius essential oils reported earlier may account for their antioxidant capacity.

  4. Synthesis and characterization of new polyamides derived from alanine and valine derivatives

    Directory of Open Access Journals (Sweden)

    El-Faham Ayman

    2012-11-01

    Full Text Available Abstract Background Many efforts have been recently devoted to design, investigate and synthesize biocompatible, biodegradable polymers for applications in medicine for either the fabrication of biodegradable devices or as drug delivery systems. Many of them consist of condensation of polymers having incorporated peptide linkages susceptible to enzymatic cleavage. Polyamides (PAs containing α-amino acid residues such as L-leucine, L-alanine and L-phenylalanine have been reported as biodegradable materials. Furthermore, polyamides (PAs derived from C10 and C14 dicarboxylic acids and amide-diamines derived from 1,6-hexanediamine or 1,12-dodecanediamine and L-phenylalanine, L-valyl-L-phenylalanine or L-phenylalanyl-L-valine residues have been reported as biocompatible polymers. We have previously described the synthesis and thermal properties of a new type of polyamides-containing amino acids based on eight new symmetric meta-oriented protected diamines derived from coupling of amino acids namely; Fomc-glycine, Fmoc-alanine, Fomc-valine and Fomc-leucine with m-phenylene diamine or 2,6-diaminopyridine. Results revealed that incorporation of pyridine onto the polymeric backbone of all series decreases the thermal stability. Here we describe another family of polyamides based on benzene dicarboxylic acid, pyridine dicarboxylic acid, and α-amino acid linked to benzidine and 4,4′-oxydianiline to study the effect of the dicarboxylic acid as well as the amino acids on the nature and thermal stability of the polymers. Results We report here the preparation of a new type of polyamides based on benzene dicarboxylic acid, pyridine dicarboxylic acid, and α-amino acid linked to benzidine and 4,4′-oxydianiline to study the effect of the dicarboxylic acid as well as the amino acids on the nature and thermal stability of polymers. The thermal properties of the polymers were evaluated by different techniques. Results revealed that structure-thermal property

  5. Sequence-selective single-molecule alkylation with a pyrrole-imidazole polyamide visualized in a DNA nanoscaffold.

    Science.gov (United States)

    Yoshidome, Tomofumi; Endo, Masayuki; Kashiwazaki, Gengo; Hidaka, Kumi; Bando, Toshikazu; Sugiyama, Hiroshi

    2012-03-14

    We demonstrate a novel strategy for visualizing sequence-selective alkylation of target double-stranded DNA (dsDNA) using a synthetic pyrrole-imidazole (PI) polyamide in a designed DNA origami scaffold. Doubly functionalized PI polyamide was designed by introduction of an alkylating agent 1-(chloromethyl)-5-hydroxy-1,2-dihydro-3H-benz[e]indole (seco-CBI) and biotin for sequence-selective alkylation at the target sequence and subsequent streptavidin labeling, respectively. Selective alkylation of the target site in the substrate DNA was observed by analysis using sequencing gel electrophoresis. For the single-molecule observation of the alkylation by functionalized PI polyamide using atomic force microscopy (AFM), the target position in the dsDNA (∼200 base pairs) was alkylated and then visualized by labeling with streptavidin. Newly designed DNA origami scaffold named "five-well DNA frame" carrying five different dsDNA sequences in its cavities was used for the detailed analysis of the sequence-selectivity and alkylation. The 64-mer dsDNAs were introduced to five individual wells, in which target sequence AGTXCCA/TGGYACT (XY = AT, TA, GC, CG) was employed as fully matched (X = G) and one-base mismatched (X = A, T, C) sequences. The fully matched sequence was alkylated with 88% selectivity over other mismatched sequences. In addition, the PI polyamide failed to attach to the target sequence lacking the alkylation site after washing and streptavidin treatment. Therefore, the PI polyamide discriminated the one mismatched nucleotide at the single-molecule level, and alkylation anchored the PI polyamide to the target dsDNA.

  6. Differential Scavenging Among Pig, Rabbit, and Human Subjects.

    Science.gov (United States)

    Steadman, Dawnie Wolfe; Dautartas, Angela; Kenyhercz, Michael W; Jantz, Lee M; Mundorff, Amy; Vidoli, Giovanna M

    2018-04-12

    Different animal species have been used as proxies for human remains in decomposition studies for decades, although few studies have sought to validate their use in research aimed at estimating the postmortem interval. This study examines 45 pig, rabbit, and human subjects placed in three seasonal trials at the Anthropology Research Facility. In an earlier paper, we found that overall decomposition trends did vary between species that could be due to differential insect and scavenger behavior. This study specifically examines if scavenger behavior differs by carrion species. Daily photographs, game camera photographs, written observations, and Total Body Score (TBS) documented scavenging and decomposition changes. Results show that raccoons were the most commonly observed vertebrate scavenger, that scavenging was most extensive in winter, and that certain human subjects were preferred over other humans and all non-human subjects. Finally, scavenging activity greatly reduces the accuracy of postmortem interval estimates based on TBS. © 2018 American Academy of Forensic Sciences.

  7. Radical scavenging potentials of single and combinatorial herbal formulations in vitro

    Directory of Open Access Journals (Sweden)

    Okey A. Ojiako

    2016-04-01

    Full Text Available Reactive oxygen and nitrogen species (RONS are involved in deleterious/beneficial biological processes. The present study sought to investigate the capacity of single and combinatorial herbal formulations of Acanthus montanus, Emilia coccinea, Hibiscus rosasinensis, and Asystasia gangetica to act as superoxide radicals (SOR, hydrogen peroxide (HP, nitric oxide radical (NOR, hydroxyl radical (HR, and 2,2-diphenyl-1-picrylhydrazyl (DPPH radical antagonists using in vitro models. The herbal extracts were single herbal formulations (SHfs, double herbal formulations (DHfs, triple herbal formulations (THfs, and a quadruple herbal formulation (QHf. The phytochemical composition and radical scavenging capacity index (SCI of the herbal formulations were measured using standard methods. The flavonoids were the most abundant phytochemicals present in the herbal extracts. The SCI50 defined the concentration (μg/mL of herbal formulation required to scavenge 50% of the investigated radicals. The SHfs, DHfs, THfs, and QHf SCI50 against the radicals followed the order HR > SOR > DPPH radical > HP > NOR. Although the various herbal formulations exhibited ambivalent antioxidant activities in terms of their radical scavenging capabilities, a broad survey of the results of the present study showed that combinatorial herbal formulations (DHfs, THfs, and QHf appeared to exhibit lower radical scavenging capacities than those of the SHfs in vitro.

  8. SYNTHESIS AND CHARACTERIZATION OF NEW THERMALLY STABLE POLYAMIDES BASED ON 2,5-PYRIDINE DICARBOXYLIC ACID AND AROMATIC DIAMINES

    OpenAIRE

    FAGHIHI, KHALIL

    2009-01-01

    Six new thermally stable polyamides 3a-f were synthesized through the polycondensation reaction of 2,5-pyridine dicarboxylic acid 1 with six different derivatives of aromatic diamines 2a-f in amedium consisting of N-methyl-2-pyrrolidone, triphenyl phosphite, calcium chloride and pyridine. The polycondensation reaction produced a series of novel polyamides containing pyridyl moieties in the main chain in high yield with inherent viscosities between 0.50-0.82 dL/g. The resulting polymers were f...

  9. Synthesis and Properties of New Polyamides Based on 4-Phenylenediacrylic Acid and Hydantoin Derivatives in the Main Chain

    OpenAIRE

    FAGHIHI, Khalil

    2008-01-01

    Six new polyamides (5a-f) containing p-phenylenediacrylic and hydantoin moieties in the main chain were prepared by direct polycondensation reaction of 4-phenylenediacrylic acid (3) with 6 different hydantoin derivatives (4a-f) using thionyl chloride and pyridine as condensing agents and N-methyl-2-pyrolidone as solvent. These new polymers (5a-f) were obtained in high yield and inherent viscosity between 0.35-0.55 dL/g. The resulting polyamides were characterized by elemental analysi...

  10. Evaluation of ionizing radiation effects on recycled polyamide-6 by infrared spectroscopy and measures of fluidity index

    International Nuclear Information System (INIS)

    Evora, Maria Cecilia; Goncalez, Odair Lelis

    2000-01-01

    In this work are presented partial results from a set of experiments and analyses performed at CTA and IPEN laboratories for the characterization of the polyamide-6, recycled and irradiated with a 1.5 MeV electron beam with a 500 kGy dose. The experimental determinations were carried out using infrared spectroscopy with Fourier transform (FTIR), in the medium infrared region (MIR) and in the far infrared region (FAR), to evaluate if exist significant changes in the infrared absorption region of the amide groups due to the polyamide irradiation. Characteristics relative to the measured fluidity index were used to evaluate the irradiated material crosslinking. (author)

  11. Thermal stability and degradation behavior of novel wholly aromatic azo polyamide-hydrazides

    International Nuclear Information System (INIS)

    Al-Ghamdia, R.F.; Fahmib, M.M.; Mohamed, N.A.

    2005-01-01

    Thermal stability and degradation behavior of a series of novel wholly aromatic azo polyamide-hydrazides have been investigated in nitrogen and in air atmospheres using differential scanning ealorimetry, thermogravimetry, infrared spectroscopy and elemental analysis. The influences of controlled structural variations and molecular weight on the thermal stability and degradation behavior of this series of polymers have also been studied. The structural differences were achieved by varying the content of para- and meta substituted phenylene rings incorporated within this series. The polymers were prepared by a low temperature solution polycondensation reaction of p aminosalicylic acid hydrazide and an equimolar amount of 4,4-azo dibenzoyl chloride [4,4 ADBC] or 3,3-azo dibenzoyl chloride [3,3ADBC] or mixtures of various molar ratios of 4,4ADBC and 3,3ADBC in anhydrous N,N- dimethyl acetamide [DMAc] containing lithium chloride as a solvent at -10 degree C. The results clearly reveal that these polymers are characterized by high thermal stability. Their weight loss occurred in three distinctive steps. The first was small and assigned to the evaporation of absorbed moisture. The second was appreciable and was attributed to the cyclo dehydration reaction of the hydrazide groups into 1,3,4-oxadiazole rings by losing water, combined with elimination of azo groups by losing molecular nitrogen. This is not a true degradation but rather a thermo-chemical transformation reaction of the azo polyamide-hydrasdes into the corresponding polyamide-l,3,4-oxadiazoles. The third was relatively severe and sharp, particularly in air, and corresponded to the decomposition of the resulting polyamide-l, 3,4-oxadiazoles. In both degradation atmospheres, the improved resistance to high temperatures was always associated with increased content of para- phenylene moieties of the investigated polymer. Further, with exception of 160-200 degree C temperature range, where the lower molecular weight

  12. Mechanical thermal evaluation of polyamide 6 with bentonite organo clay nanocomposites

    International Nuclear Information System (INIS)

    Paz, Rene Anisio da; Araujo, Edcleide M.; Melo, Tomas Jeferson Alves de; Leite, Amanda M.D.; Cavalcanti, Shirley Nobrega; Pessan, Luiz Antonio

    2009-01-01

    This work had for objective to obtain polymeric nanocomposites of polyamide 6 and a clay consisting of silicates layer from of Paraiba mines and to evaluate evaluation mechanical thermal in different processing conditions. The clay was organically modified using a quaternary ammonium salt (Cetremide), so that there is a larger interaction of the clay with the polymer. The obtained nanocomposites showed the morphological structure composed exfoliated/partially exfoliated, as shown XRD. The results of HDT it because the clay increases the dimensional stability of PA6 in high temperatures, making possible the use of the nanocomposites for making of pieces with good resistance to the heat distortion. (author)

  13. Polyamide microcapsules containing jojoba oil prepared by inter-facial polymerization.

    Science.gov (United States)

    Persico, P; Carfagna, C; Danicher, L; Frere, Y

    2005-08-01

    Jojoba oil containing polyamide microcapsules having diameter of approximately 5 microm were prepared by inter-facial polycondensation by direct method (oil-in-water). Qualitative effects of both the formulation and the process parameters on microcapsules characteristics were investigated by SEM observations. Morphological analysis showed the dependence of the external membrane compactness on the chemical nature of the water-soluble polyamine and the oil-soluble acid polychloride: 1,6-hexamethylenediamine (HMDA) and terephthaloyl dichloride (TDC) were found to favour the production of smooth and dense surfaces. The use of ultrasonic irradiations during the dispersion step to get a further reduction of microcapsules size was also evaluated.

  14. Composition

    DEFF Research Database (Denmark)

    Bergstrøm-Nielsen, Carl

    2014-01-01

    Cue Rondo is an open composition to be realised by improvising musicians. See more about my composition practise in the entry "Composition - General Introduction". Caution: streaming the sound/video files will in some cases only provide a few minutes' sample, or the visuals will not appear at all....... Please DOWNLOAD them to see/hear them in full length! This work is licensed under a Creative Commons "by-nc" License. You may for non-commercial purposes use and distribute it, performance instructions as well as specially designated recordings, as long as the author is mentioned. Please see http...

  15. Simulation Modeling Method and Experimental Investigation on the Uniflow Scavenging System of an Opposed-Piston Folded-Cranktrain Diesel Engine

    Directory of Open Access Journals (Sweden)

    Fukang Ma

    2017-05-01

    Full Text Available The scavenging process for opposed-piston folded-cranktrain (OPFC diesel engines can be described by the time evolution of the in-cylinder and exhaust chamber residual gas rates. The relation curve of in-cylinder and exhaust chamber residual gas rate is called scavenging profile, which is calculated through the changes of in-cylinder and exhaust chamber gas compositions determined by computational fluid dynamics (CFD simulation. The scavenging profile is used to calculate the scavenging process by mono-dimensional (1D simulation. The tracer gas method (TGM is employed to validate the accuracy of the scavenging profile. At the same time, the gas exchange performance under different intake and exhaust state parameters was examined based on the TGM. The results show that the scavenging process from 1D simulation and experiment match well, which means the scavenging model obtained by CFD simulation performs well and validation of its effectiveness by TGM is possible. The difference between intake and exhaust pressure has a significant positive effect on the gas exchange performance and trapped gas mass, but the pressure difference has little effect on the scavenging efficiency and the trapped air mass if the delivery ratio exceeds 1.4.

  16. Hybrid joining of polyamide and hydrogenated acrylonitrile butadiene rubber through heat-resistant functional layer of silane coupling agent

    Energy Technology Data Exchange (ETDEWEB)

    Sang, Jing; Sato, Riku [Department of Frontier Materials and Function Engineering, Graduate School of Engineering, Iwate University, 4-3-5 Ueda, Morioka 020-8551 (Japan); Aisawa, Sumio, E-mail: aisawa@iwate-u.ac.jp [Department of Frontier Materials and Function Engineering, Graduate School of Engineering, Iwate University, 4-3-5 Ueda, Morioka 020-8551 (Japan); Hirahara, Hidetoshi [Department of Frontier Materials and Function Engineering, Graduate School of Engineering, Iwate University, 4-3-5 Ueda, Morioka 020-8551 (Japan); Mori, Kunio [Department of Frontier Materials and Function Engineering, Graduate School of Engineering, Iwate University, 4-3-5 Ueda, Morioka 020-8551 (Japan); Sulfur Chemical Institute, 210, Collabo MIU, 4-3-5, Ueda, Morioka 020-0066 (Japan)

    2017-08-01

    Highlights: • We modify PA6 surface using silane coupling agent layer of APTMS to link HNBR. • APTMS greatly improved heat resistance of PA6 from 153 °C up to 325 °C. • A PA6/HNBR joined body was obtained, and it exhibits high adhesion strength with cohesive failure. • Chemical structures of the adhesion interfaces of PA6/HNBR were confirmed by Nano-IR. - Abstract: A simple, direct adhesion method was developed to join polyamide (PA6) to hydrogenated acrylonitrile butadiene rubber (HNBR) by grafting a functional layer of a silane coupling agent on plasma functionalized PA6 surfaces. The functional layer of the silane coupling agent was prepared using a self-assembly method, which greatly improved the heat resistance of PA6 from 153 °C up to 325 °C and the resulting PA6/HNBR joints showed excellent adhesion properties with cohesive failure between PA6 and HNBR. X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and nanoscale infrared microscopy and chemical imaging (Nano-IR, AFM-IR) were employed to characterize the surfaces and interfaces. The Nano-IR analysis method was employed for the first time to analyze the chemical structures of the adhesion interfaces between different materials and to establish the interface formation mechanism. This study is of significant value for interface research and the study of adhesion between resins and rubbers. There is a promising future for heat-resistant functional layers on resin surfaces, with potential application in fuel hose composite materials for the automotive and aeronautical industries.

  17. Polyamide 4,6 nanocomposites with and without the use of a maleated polyolefin elastomer as a toughener

    International Nuclear Information System (INIS)

    Chiu, Fang-Chyou; Deng, Tsung-Lin

    2011-01-01

    In this study, polyamide 4,6 (PA 4,6)-based nanocomposites were successfully prepared using a twin screw extruder. A commercial organo-montmorillonite (denoted as 30B) and a commercial maleated polyolefin elastomer (denoted as POEMA) served as the reinforcing filler and toughener, respectively. X-ray diffraction (XRD) and transmission electron microscopy (TEM) results confirmed the nano-scaled dispersion of 30B in the composites. Nevertheless, the presence of POEMA slightly depreciated the dispersibility of 30B. Polarized light microscope (PLM) observations showed that the inclusions of 30B and POEMA led to the formation of diffused/broken PA 4,6 spherulites. Differential scanning calorimetry (DSC) results indicated that the addition of 30B retarded the crystallization of PA 4,6; the addition of POEMA led to a similar retardation effect on PA 4,6 crystallization. Interesting melting behaviors associated mainly with the crystal annealing of PA 4,6 upon heating were observed for the fast-cooled samples. The presence of POEMA was noted to hamper the annealing process of PA 4,6 crystals. The thermal stability enhancement of PA 4,6 in the presence of 30B was further raised to a higher extent when POEMA was included in the matrix. The rigidity, including the storage/Young's/flexural moduli, of PA 4,6 significantly increased after adding 30B. These properties, however, declined after the additional incorporation of POEMA. The PA 4,6/POEMA/30B nanocomposites basically displayed balanced impact strength between those of the neat PA 4,6 and PA 4,6/POEMA blends.

  18. Radical scavenging activity of crude polysaccharides from Camellia sinensis

    Directory of Open Access Journals (Sweden)

    Yang Fan

    2011-01-01

    Full Text Available A preparation of crude polysaccharides (TPS was isolated from Camellia sinensis by precipitation and ultrafiltration. TPS1, TPS2, and TPS3 had molecular weights of 240, 21.4, and 2.46 kDa, respectively. The radical scavenging activities of TPS were evaluated by DPPH free radical, hydroxyl radical and superoxide radical scavenging. These results revealed that TPS exhibited strong radical scavenging activity in a concentration-dependent manner. TPS3 with lowest molecular weight showed a higher radical scavenging activity.

  19. High-performance polyamide thin-film composite nanofiltration membrane: Role of thermal treatment

    Science.gov (United States)

    Liu, Baicang; Wang, Shuai; Zhao, Pingju; Liang, Heng; Zhang, Wen; Crittenden, John

    2018-03-01

    Nanofiltration (NF) membranes have many excellent applications (e.g., removing multivalent ions and pretreating water before reverse osmosis, RO), but their relatively high cost limits their application. Especially in recent years, researchers have paid substantial attention to reducing the cost of NF membranes. In this paper, high-performance NF membranes were fabricated using interfacial polymerization (IP) methods. The polymer concentration, IP solution concentration, and thermal treatment conditions were varied. The synthesized membranes were characterized using scanning electron microscopy (SEM), atomic force microscopy (AFM), a contact angle goniometer, X-ray photoelectron spectroscopy (XPS), attenuated total reflectance fourier transform infrared (ATR-FTIR) spectroscopy, and performance tests. The results show that water flux was significantly improved using a hot-water thermal treatment method. Our fabricated thermal-treated NF membrane had an approximately 15% higher water permeability with a value of 13.6 L/(m2 h bar) than that of the commercially available GE HL membrane with a value of 11.8 L/(m2 h bar). Our membranes had the same MgSO4 rejection as that of the GE HL membrane. We found that the thermal treatment causes the NF membrane surface to be smoother and have a high crosslinking degree.

  20. Modification of Polyamide-Urethane (PAUt Thin Film Composite Membrane for Improving the Reverse Osmosis Performance

    Directory of Open Access Journals (Sweden)

    Li-Fen Liu

    2018-03-01

    Full Text Available In the current study, the poly (amide-urethane (PAUt membranes were successfully fabricated by interfacial polymerization of m-phenylenediamine (MPD and 5-choroformyloxyisophaloyl chloride (CFIC on the polysulfone substrates. Two modification methods based on layer-by-layer assembly were applied to modify the PAUt membrane surface to achieve antifouling property: 1. Chitosan (CS was directly self-assembled on the PAUt membrane (i.e., PAUt-CS; and 2. polydimethyl diallyl ammonium chloride (PDDA, polystyrene sulfonate (PSS, and CS were successively self-assembled on the membrane surface (i.e., PAUt-PDDA/PSS/CS. The resultant membranes were symmetrically characterized by Attenuated Total Reflection Fourier Transform Infrared Spectroscopy (ATR-FTIR, X-ray Photoelectron Spectroscopy (XPS, Scanning Electron Microscopy (SEM, Atomic Force Microscopy (AFM and Contact Angle Meter (CAM, respectively. The results indicated that the modified membranes had much smoother and more hydrophilic surfaces as compared to the nascent PAUt membrane. Meanwhile, the modified membranes exhibited better reverse osmosis performance in terms of water permeability and salt rejection. After the modified membranes were fouled by lake water, the PAUt-PDDA/PSS/CS membrane presented the best antifouling performance among the three types of membranes. Combining the reverse osmosis performance with the anti-fouling property obviously, the PAUt-PDDA/PSS/CS membrane behaved as a promising candidate to be used in real applications.

  1. Aromatic polyamide short fibres-reinforced elastomers: adhesion mechanisms and the composite's performance properties

    NARCIS (Netherlands)

    Sadatshirazi, S.

    2012-01-01

    The current thesis consists of a chapter as literature review in which different scientific sources and the results of investigation of various researchers are reviewed, followed by 5 chapters (2 to 6) and an appendix covering the results of the experimental work performed. The results can be

  2. Rain scavenging studies. Progress report No. 11

    International Nuclear Information System (INIS)

    Dingle, A.N.

    1975-05-01

    The modeling of convective storm scavenging processes is going forward on two distinct fronts. The first of these relates to the microphysical processes, particularly to the study of their response to micro-dynamical components of the convective circulation. It is found that the droplet size spectra generated are responsive to variations of vertical velocity due to turbulence within the cloud and to humidity variations due to entrainment processes. Both sets of variations give responses that differ for different amplitudes and frequencies, i.e., rapid, small-amplitude eddies appear to enhance small-droplet development, whereas slow, large-amplitude oscillations tend to enhance large-droplet development. An allied study of the assumptions used in the microphysical equations is also being made. The second modeling effort is addressed to the problem of three-dimensional representation of convective dynamics. Equations are presented, and some of the problems under attack are discussed

  3. Carcass Type Affects Local Scavenger Guilds More than Habitat Connectivity.

    Directory of Open Access Journals (Sweden)

    Zachary H Olson

    Full Text Available Scavengers and decomposers provide an important ecosystem service by removing carrion from the environment. Scavenging and decomposition are known to be temperature-dependent, but less is known about other factors that might affect carrion removal. We conducted an experiment in which we manipulated combinations of patch connectivity and carcass type, and measured responses by local scavenger guilds along with aspects of carcass depletion. We conducted twelve, 1-month trials in which five raccoon (Procyon lotor, Virginia opossum (Didelphis virginiana, and domestic rabbit (Oryctolagus spp. carcasses (180 trials total were monitored using remote cameras in 21 forest patches in north-central Indiana, USA. Of 143 trials with complete data, we identified fifteen species of vertebrate scavengers divided evenly among mammalian (N = 8 and avian species (N = 7. Fourteen carcasses (9.8% were completely consumed by invertebrates, vertebrates exhibited scavenging behavior at 125 carcasses (87.4%, and four carcasses (2.8% remained unexploited. Among vertebrates, mammals scavenged 106 carcasses, birds scavenged 88 carcasses, and mammals and birds scavenged 69 carcasses. Contrary to our expectations, carcass type affected the assemblage of local scavenger guilds more than patch connectivity. However, neither carcass type nor connectivity explained variation in temporal measures of carcass removal. Interestingly, increasing richness of local vertebrate scavenger guilds contributed moderately to rates of carrion removal (≈6% per species increase in richness. We conclude that scavenger-specific differences in carrion utilization exist among carcass types and that reliable delivery of carrion removal as an ecosystem service may depend on robust vertebrate and invertebrate communities acting synergistically.

  4. Carcass Type Affects Local Scavenger Guilds More than Habitat Connectivity

    Science.gov (United States)

    Olson, Zachary H.; Beasley, James C.; Rhodes, Olin E.

    2016-01-01

    Scavengers and decomposers provide an important ecosystem service by removing carrion from the environment. Scavenging and decomposition are known to be temperature-dependent, but less is known about other factors that might affect carrion removal. We conducted an experiment in which we manipulated combinations of patch connectivity and carcass type, and measured responses by local scavenger guilds along with aspects of carcass depletion. We conducted twelve, 1-month trials in which five raccoon (Procyon lotor), Virginia opossum (Didelphis virginiana), and domestic rabbit (Oryctolagus spp.) carcasses (180 trials total) were monitored using remote cameras in 21 forest patches in north-central Indiana, USA. Of 143 trials with complete data, we identified fifteen species of vertebrate scavengers divided evenly among mammalian (N = 8) and avian species (N = 7). Fourteen carcasses (9.8%) were completely consumed by invertebrates, vertebrates exhibited scavenging behavior at 125 carcasses (87.4%), and four carcasses (2.8%) remained unexploited. Among vertebrates, mammals scavenged 106 carcasses, birds scavenged 88 carcasses, and mammals and birds scavenged 69 carcasses. Contrary to our expectations, carcass type affected the assemblage of local scavenger guilds more than patch connectivity. However, neither carcass type nor connectivity explained variation in temporal measures of carcass removal. Interestingly, increasing richness of local vertebrate scavenger guilds contributed moderately to rates of carrion removal (≈6% per species increase in richness). We conclude that scavenger-specific differences in carrion utilization exist among carcass types and that reliable delivery of carrion removal as an ecosystem service may depend on robust vertebrate and invertebrate communities acting synergistically. PMID:26886299

  5. Carcass Type Affects Local Scavenger Guilds More than Habitat Connectivity.

    Science.gov (United States)

    Olson, Zachary H; Beasley, James C; Rhodes, Olin E

    2016-01-01

    Scavengers and decomposers provide an important ecosystem service by removing carrion from the environment. Scavenging and decomposition are known to be temperature-dependent, but less is known about other factors that might affect carrion removal. We conducted an experiment in which we manipulated combinations of patch connectivity and carcass type, and measured responses by local scavenger guilds along with aspects of carcass depletion. We conducted twelve, 1-month trials in which five raccoon (Procyon lotor), Virginia opossum (Didelphis virginiana), and domestic rabbit (Oryctolagus spp.) carcasses (180 trials total) were monitored using remote cameras in 21 forest patches in north-central Indiana, USA. Of 143 trials with complete data, we identified fifteen species of vertebrate scavengers divided evenly among mammalian (N = 8) and avian species (N = 7). Fourteen carcasses (9.8%) were completely consumed by invertebrates, vertebrates exhibited scavenging behavior at 125 carcasses (87.4%), and four carcasses (2.8%) remained unexploited. Among vertebrates, mammals scavenged 106 carcasses, birds scavenged 88 carcasses, and mammals and birds scavenged 69 carcasses. Contrary to our expectations, carcass type affected the assemblage of local scavenger guilds more than patch connectivity. However, neither carcass type nor connectivity explained variation in temporal measures of carcass removal. Interestingly, increasing richness of local vertebrate scavenger guilds contributed moderately to rates of carrion removal (≈6% per species increase in richness). We conclude that scavenger-specific differences in carrion utilization exist among carcass types and that reliable delivery of carrion removal as an ecosystem service may depend on robust vertebrate and invertebrate communities acting synergistically.

  6. Design and Characterization of Electrospun Polyamide Nanofiber Media for Air Filtration Applications

    Directory of Open Access Journals (Sweden)

    Jonas Matulevicius

    2014-01-01

    Full Text Available Electrospun polyamide 6 (PA 6 and polyamide 6/6 (PA 6/6 nanofibers were produced in order to investigate their experimental characteristics with the goal of obtaining filtration relevant fiber media. The experimental design model of each PA nanofibers contained the following variables: polymer concentration, ratio of solvents, nanofiber media collection time, tip-to-collector distance, and the deposition voltage. The average diameter of the fibers, their morphology, basis weight, thickness, and resulting media solidity were investigated. Effects of each variable on the essential characteristics of PA 6/6 and PA 6 nanofiber media were studied. The comparative analysis of the obtained PA 6/6 and PA 6 nanofiber characteristics revealed that PA 6/6 had higher potential to be used in filtration applications. Based on the experimental results, the graphical representation—response surfaces—for obtaining nanofiber media with the desirable fiber diameter and basis weight characteristics were derived. Based on the modelling results the nanofiber filter media (mats were fabricated. Filtration results revealed that nanofiber filter media electrospun from PA6/6 8% (w/vol solutions with the smallest fiber diameters (62–66 nm had the highest filtration efficiency (PA6/6_30 = 84.9–90.9% and the highest quality factor (PA6/6_10 = 0.0486–0.0749 Pa−1.

  7. An HRE-Binding Py-Im Polyamide Impairs Hypoxic Signaling in Tumors.

    Science.gov (United States)

    Szablowski, Jerzy O; Raskatov, Jevgenij A; Dervan, Peter B

    2016-04-01

    Hypoxic gene expression contributes to the pathogenesis of many diseases, including organ fibrosis, age-related macular degeneration, and cancer. Hypoxia-inducible factor-1 (HIF1), a transcription factor central to the hypoxic gene expression, mediates multiple processes including neovascularization, cancer metastasis, and cell survival. Pyrrole-imidazole polyamide 1: has been shown to inhibit HIF1-mediated gene expression in cell culture but its activity in vivo was unknown. This study reports activity of polyamide 1: in subcutaneous tumors capable of mounting a hypoxic response and showing neovascularization. We show that 1: distributes into subcutaneous tumor xenografts and normal tissues, reduces the expression of proangiogenic and prometastatic factors, inhibits the formation of new tumor blood vessels, and suppresses tumor growth. Tumors treated with 1: show no increase in HIF1α and have reduced ability to adapt to the hypoxic conditions, as evidenced by increased apoptosis in HIF1α-positive regions and the increased proximity of necrotic regions to vasculature. Overall, these results show that a molecule designed to block the transcriptional activity of HIF1 has potent antitumor activity in vivo, consistent with partial inhibition of the tumor hypoxic response. Mol Cancer Ther; 15(4); 608-17. ©2015 AACR. ©2015 American Association for Cancer Research.

  8. Nitric oxide radical scavenging potential of some Elburz medicinal ...

    African Journals Online (AJOL)

    Some plants scavenge nitric oxide (NO) with high affinity. For this purpose, forty extracts from 26 medicinal plants, growing extensively in Elburz mountains, were evaluated for their NO scavenging activity. Total phenolic and flavonoid contents of these extracts were also measured by Folin Ciocalteu and AlCl3 colorimetric ...

  9. Free Radical Scavenging Activities of Methanol Extract and ...

    African Journals Online (AJOL)

    Michael Horsfall

    fractions were subjected to in vitro antioxidant evaluation using the DPPH free radical scavenging ... The crude extract has IC-50 value for radical scavenging activity of 5μg/mL which was .... effective concentration of the sample that is required.

  10. Modeling of an Integrated Electromagnetic Generator for Energy Scavenging

    NARCIS (Netherlands)

    Lu, J.; Kovalgin, Alexeij Y.; Schmitz, Jurriaan

    2007-01-01

    The ubiquitous deploying of wireless electronic devices due to pervasive computing results in the idea of Energy Scavenging, i.e., harvesting ambient energy from surroundings of the electronic devices. As an approach to possible practical realization of such an energy scavenger, we aim at the

  11. Radical Scavenging Efficacy of Thiol Capped Silver Nanoparticles

    Indian Academy of Sciences (India)

    aSchool of Studies in Chemistry, Pt. Ravishankar Shukla University, Raipur 492 010, India. bDepartment of ... of nanosilver in foods, health care and consumer products as antimi- ... of the radical scavenging behavior of thiolated antiox- idants (alone) and ..... case of GSH@AgNPs; DPPH scavenging activity was found to be ...

  12. Identification of Radical Scavengers in Sweet Grass (Hierochloe odorata)

    NARCIS (Netherlands)

    Pukalskas, A.; Beek, van T.A.; Venskutonis, R.P.; Linssen, J.P.H.; Veldhuizen, van A.; Groot, de Æ.

    2002-01-01

    Extracts from aerial parts of sweet grass (Hierochloe odorata) were active DPPH free radical scavengers, The active compounds were detected in extract fractions using HPLC with on-line radical scavenging detection. After multistep fractionation of the extract, two new natural products possessing

  13. Characterization and DPPH Radical Scavenging Activity of Gallic ...

    African Journals Online (AJOL)

    Characterization and DPPH Radical Scavenging Activity of Gallic Acid-Lecithin Complex. C Liu, C Chen, H Ma, E Yuan, Q Li. Abstract. Purpose: To investigate the physicochemical properties and DPPH radical scavenging activity of gallic acid–lecithin complex. Methods: The complex of gallic acid with lecithin was prepared ...

  14. Fire resistant polyamide based on 1-(diorganooxyphosphonyl)methyl-2,4- and -2,6diamino benzene

    Science.gov (United States)

    Mikroyannidis, J. A. (Inventor); Kourtides, D. A. (Inventor)

    1986-01-01

    1-(Diorganooxyphosphonyl)methyl2,4- and-2,6diamino benzenes are reacted with polyacylhalides and optionally comonomers to produce polyamides which have desirable heat and fire resistance properties. These polymers are used to form fibers and fabrics where fire resistance properties are important, e.g., aircraft equipment and structures.

  15. Rigid, bio-based polyamides from galactaric acid derivatives with elevated glass transition temperatures and their characterization

    NARCIS (Netherlands)

    Wróblewska, Aleksandra A.; Bernaerts, Katrien; de Wildeman, Stefaan

    2017-01-01

    A comparative study was prepared investigating the synthesis of polyamides using bio-based building blocks derived from sugar beet pulp, namely 2,3:4,5-di-O-methylene-galactarate (GalXH) and 2,3:4,5-di-O-isopropylidene-galactarate (GalXMe) derivatives. Two different approaches towards the synthesis

  16. Thermo-oxidative degradation study of melt-processed polyethylene and its blend with polyamide using time-resolved rheometry

    CSIR Research Space (South Africa)

    Salehiyan, Reza

    2017-05-01

    Full Text Available Time-resolved mechanical spectroscopy (TRMS) was conducted to study the thermo-oxidative degradation of linear low density polyethylene (LLDPE) samples with different thermal histories and their blends with a polyamide (PA6) in the melt state. Neat...

  17. Effects of vulture exclusion on carrion consumption by facultative scavengers.

    Science.gov (United States)

    Hill, Jacob E; DeVault, Travis L; Beasley, James C; Rhodes, Olin E; Belant, Jerrold L

    2018-03-01

    Vultures provide an essential ecosystem service through removal of carrion, but globally, many populations are collapsing and several species are threatened with extinction. Widespread declines in vulture populations could increase the availability of carrion to other organisms, but the ways facultative scavengers might respond to this increase have not been thoroughly explored. We aimed to determine whether facultative scavengers increase carrion consumption in the absence of vulture competition and whether they are capable of functionally replacing vultures in the removal of carrion biomass from the landscape. We experimentally excluded 65 rabbit carcasses from vultures during daylight hours and placed an additional 65 carcasses that were accessible to vultures in forested habitat in South Carolina, USA during summer (June-August). We used motion-activated cameras to compare carrion use by facultative scavenging species between the experimental and control carcasses. Scavenging by facultative scavengers did not increase in the absence of competition with vultures. We found no difference in scavenger presence between control carcasses and those from which vultures were excluded. Eighty percent of carcasses from which vultures were excluded were not scavenged by vertebrates, compared to 5% of carcasses that were accessible to vultures. At the end of the 7-day trials, there was a 10.1-fold increase in the number of experimental carcasses that were not fully scavenged compared to controls. Facultative scavengers did not functionally replace vultures during summer in our study. This finding may have been influenced by the time of the year in which the study took place, the duration of the trials, and the spacing of carcass sites. Our results suggest that under the warm and humid conditions of our study, facultative scavengers would not compensate for loss of vultures. Carcasses would persist longer in the environment and consumption of carrion would likely shift from

  18. Invasive carnivores alter ecological function and enhance complementarity in scavenger assemblages on ocean beaches.

    Science.gov (United States)

    Brown, Marion B; Schlacher, Thomas A; Schoeman, David S; Weston, Michael A; Huijbers, Chantal M; Olds, Andrew D; Connolly, Rod M

    2015-10-01

    Species composition is expected to alter ecological function in assemblages if species traits differ strongly. Such effects are often large and persistent for nonnative carnivores invading islands. Alternatively, high similarity in traits within assemblages creates a degree of functional redundancy in ecosystems. Here we tested whether species turnover results in functional ecological equivalence or complementarity, and whether invasive carnivores on islands significantly alter such ecological function. The model system consisted of vertebrate scavengers (dominated by raptors) foraging on animal carcasses on ocean beaches on two Australian islands, one with and one without invasive red foxes (Vulpes vulpes). Partitioning of scavenging events among species, carcass removal rates, and detection speeds were quantified using camera traps baited with fish carcasses at the dune-beach interface. Complete segregation of temporal foraging niches between mammals (nocturnal) and birds (diurnal) reflects complementarity in carrion utilization. Conversely, functional redundancy exists within the bird guild where several species of raptors dominate carrion removal in a broadly similar way. As predicted, effects of red foxes were large. They substantially changed the nature and rate of the scavenging process in the system: (1) foxes consumed over half (55%) of all carrion available at night, compared with negligible mammalian foraging at night on the fox-free island, and (2) significant shifts in the composition of the scavenger assemblages consuming beach-cast carrion are the consequence of fox invasion at one island. Arguably, in the absence of other mammalian apex predators, the addition of red foxes creates a new dimension of functional complementarity in beach food webs. However, this functional complementarity added by foxes is neither benign nor neutral, as marine carrion subsidies to coastal red fox populations are likely to facilitate their persistence as exotic

  19. Further assessment of scavenging feed resource base

    International Nuclear Information System (INIS)

    Sonaiya, E.B.; Dazogbo, J.S.; Olukosi, O.A.

    2002-01-01

    The scavenging feed resource base (SFRB) was estimated in four villages located in a rainforest ecozone in Nigeria. The average SFRB estimated for the villages was 110 kg dry weight/family flock/year. Productivity of the birds in the villages was low. A low survivability of chicks was detected indicating a lot of wastage of eggs that could have been used for human consumption. The SFRB was low in nutritive value with less than 2 g crude protein (CP) available to each bird daily. To more quantitatively describe the SFRB, the concept of using bird unit in determining what is available to each bird is suggested. This helped in evaluating at first glance the differential accessibility of each class of bird to the SFRB and assisted in strategic supplementation of the SFRB. The use of predictors of the SFRB could help in establishing prediction equation which would help in predicting the carrying capacity of the SFRB and in determining the optimum flock biomass more accurately. (author)

  20. Scavenger hunt in the CERN Computing Centre

    CERN Multimedia

    CERN Bulletin

    2013-01-01

    Hidden among the racks of servers and disks in the CERN Computing Centre, you’ll find Hawaiian dancers, space aliens, gorillas… all LEGO® figurines! These characters were placed about the Centre for the arrival of Google’s Street View team for the world to discover.   PLEASE NOTE THAT THE COMPETITION IS OVER. ONLY FOR REFERENCE, HERE IS THE ORIGINAL ARTICLE. We’re pleased to announce our first global scavenger hunt! Spot three LEGO® figurines using Google’s Street View and you’ll be entered to win a gift of your choice from our CERN Gift Guide. A LEGO® figurine in the CERN Computing Centre, as seen on Google Street View. Here are the details: Find at least three LEGO® figurines hidden around the CERN Computing Centre using Google Street View.   Take screencaps of the figurines and e-mail the pictures to TreasureHunt-ComputingCentre@cern.ch. This email is no longer active.   The...

  1. HUNT: Scavenger Hunt with Augmented Reality

    Directory of Open Access Journals (Sweden)

    Yan Lu

    2015-04-01

    Full Text Available This project shows a creative approach to the familiar scavenger hunt game. It involved the implementation of an iPhone application, HUNT, with Augmented Reality (AR capability for the users to play the game as well as an administrative website that game organizers can use to create and make available games for users to play. Using the HUNT mobile app, users will first make a selection from a list of games, and they will then be shown a list of objects that they must seek. Once the user finds a correct object and scans it with the built-in camera on the smartphone, the application will attempt to verify if it is the correct object and then display associated multi-media AR content that may include images and videos overlaid on top of real world views. HUNT not only provides entertaining activities within an environment that players can explore, but the AR contents can serve as an educational tool. The project is designed to increase user involvement by using a familiar and enjoyable game as a basis and adding an educational dimension by incorporating AR technology and engaging and interactive multimedia to provide users with facts about the objects that they have located

  2. A numerical model of aerosol scavenging

    International Nuclear Information System (INIS)

    Bradley, M.M.; Molenkamp, C.R.

    1991-10-01

    Using a three-dimensional numerical cloud/smoke-plume model, we have simulated the burning of a large, mid-latitude city following a nuclear exchange. The model includes 18 dynamic and microphysical equations that predict the fire-driven airflow, cloud processes, and smoke-cloud interactions. In the simulation, the intense heating from the burning city produces a firestorm with updraft velocities exceeding 60 m/s. Within 15 minutes of ignition, the smoke plume penetrates the tropopause. The updraft triggers a cumulonimbus cloud that produces significant quantities of ice, snow, and hail. These solid hydrometeors, as well as cloud droplets and rain, interact with the smoke particles from the fire. At the end of the one-hour simulation, over 20% of the smoke is in slowly falling snowflakes. If the snow reaches the ground before the flakes completely sublimate (or melt and then evaporate), then only approximately 50% of the smoke will survive the scavenging processes and remain in the atmosphere to affect the global climate

  3. Magnetic graphene based nanocomposite for uranium scavenging

    Energy Technology Data Exchange (ETDEWEB)

    El-Maghrabi, Heba H. [Egyptian Petroleum Research Institute, 11727, Cairo (Egypt); Abdelmaged, Shaimaa M. [Nuclear Materials Authority, 6530 P.O. Box Maadi, Cairo (Egypt); Nada, Amr A. [Egyptian Petroleum Research Institute, 11727, Cairo (Egypt); Zahran, Fouad, E-mail: f.zahran@quim.ucm.es [Faculty of Science, Helwan University, 11795, Cairo (Egypt); El-Wahab, Saad Abd; Yahea, Dena [Faculty of Science, Ain shams University, Cairo (Egypt); Hussein, G.M.; Atrees, M.S. [Nuclear Materials Authority, 6530 P.O. Box Maadi, Cairo (Egypt)

    2017-01-15

    Graphical abstract: Graphical representation of U{sup 6+} adsorption on Magnetic Ferberite-Graphene Nanocomposite. - Highlights: • Synthesis of new magnetic wolframite bimetallic nanostructure on graphene. • A promising adsorption capacity of 455 mg/g was recorded for FG-20 within 60 min at room temperature. • The uranium removal was followed pseudo-second order kinetics and Langmuir isotherm. - Abstract: Magnetic graphene based ferberite nanocomposite was tailored by simple, green, low cost and industrial effective method. The microstructure and morphology of the designed nanomaterials were examined via XRD, Raman, FTIR, TEM, EDX and VSM. The prepared nanocomposites were introduced as a novel adsorbent for uranium ions scavenging from aqueous solution. Different operating conditions of time, pH, initial uranium concentration, adsorbent amount and temperature were investigated. The experimental data shows a promising adsorption capacity. In particular, a maximum value of 455 mg/g was obtained within 60 min at room temperature with adsorption efficiency of 90.5%. The kinetics and isotherms adsorption data were fitted with the pseudo-second order model and Langmuir equation, respectively. Finally, the designed nanocomposites were found to have a great degree of sustainability (above 5 times of profiteering) with a complete maintenance of their parental morphology and adsorption capacity.

  4. Highly Porous, Rigid-Rod Polyamide Aerogels with Superior Mechanical Properties and Unusually High Thermal Conductivity.

    Science.gov (United States)

    Williams, Jarrod C; Nguyen, Baochau N; McCorkle, Linda; Scheiman, Daniel; Griffin, Justin S; Steiner, Stephen A; Meador, Mary Ann B

    2017-01-18

    We report here the fabrication of polyamide aerogels composed of poly-p-phenylene-terephthalamide, the same backbone chemistry as DuPont's Kevlar. The all-para-substituted polymers gel without the use of cross-linker and maintain their shape during processing-an improvement over the meta-substituted cross-linked polyamide aerogels reported previously. Solutions containing calcium chloride (CaCl 2 ) and para-phenylenediamine (pPDA) in N-methylpyrrolidinone (NMP) at low temperature are reacted with terephthaloyl chloride (TPC). Polymerization proceeds over the course of 5 min resulting in gelation. Removal of the reaction solvent via solvent exchange followed by extraction with supercritical carbon dioxide provides aerogels with densities ranging from 0.1 to 0.3 g/cm 3 , depending on the concentration of calcium chloride, the formulated number of repeat units, n, and the concentration of polymer in the reaction mixture. These variables were assessed in a statistical experimental study to understand their effects on the properties of the aerogels. Aerogels made using at least 30 wt % CaCl 2 had the best strength when compared to aerogels of similar density. Furthermore, aerogels made using 30 wt % CaCl 2 exhibited the lowest shrinkage when aged at elevated temperatures. Notably, whereas most aerogel materials are highly insulating (thermal conductivities of 10-30 mW/m K), the polyamide aerogels produced here exhibit remarkably high thermal conductivities (50-80 mW/(m K)) at the same densities as other inorganic and polymer aerogels. These high thermal conductivities are attributed to efficient phonon transport by the rigid-rod polymer backbone. In conjunction with their low cost, ease of fabrication with respect to other polymer aerogels, low densities, and high mass-normalized strength and stiffness properties, these aerogels are uniquely valuable for applications such as lightweighting in consumer electronics, automobiles, and aerospace where weight reduction is

  5. The research progress of several kinds of free radical scavengers

    International Nuclear Information System (INIS)

    Qian Liren; Huang Yuecheng; Cai Jianming

    2009-01-01

    Ionization radiation can generate free radicals in biological system, which could induce lipid peroxi-dation, biomacromolecule and biomembrane damage, lost of cell function, cell cycle disturbance, genetic mutation and so on. The scavenging free radicals can protect organism from radiation damage. Many radio-protective agents, such as amylase, hydroxyl-benzene derivatives, hormone, vitamin, have great abilities to protect organism from radiation via scavenging free radicals. In this paper, we mainly review the free radical scavenging effects of several kinds of radio-protective agents. (authors)

  6. Characterization of an aluminum-filled polyamide powder for applications in selective laser sintering

    International Nuclear Information System (INIS)

    Mazzoli, Alida; Moriconi, Giacomo; Pauri, Marco Giuseppe

    2007-01-01

    Solid free-form fabrication (SFF) techniques use layer-based manufacturing to create physical objects directly from computer-generated models. Using an additive approach to manufacture shapes, SFF systems join liquid, powder or sheet materials. Selective laser sintering (SLS) is a SFF technique by which parts are built layer-by-layer offering the key advantage of the direct manufacturing of functional parts. In SLS, a laser beam is traced over the surface of a tightly compacted powder made of thermoplastic material. In this paper is characterized a new aluminum-filled polyamide powder developed for applications in SLS. This material is promising for many applications that require a metallic look of the part, good finishing properties, high stiffness and higher part quality

  7. The surface characteristics of hyperbranched polyamide modified corncob and its adsorption property for Cr(VI)

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Hai, E-mail: linhai@ces.ustb.edu.cn [School of Energy and Environmental Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Beijing Key Laboratory on Resource-oriented Treatment of Industrial Pollutants, Beijing 100083 (China); Han, Shaoke; Dong, Yingbo; He, Yinhai [School of Energy and Environmental Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Beijing Key Laboratory on Resource-oriented Treatment of Industrial Pollutants, Beijing 100083 (China)

    2017-08-01

    Highlights: • An anion adsorbent was synthesized by hyperbranched polyamide modified corncob (HPMC). • The surface characteristics of samples (RCC, HPMC, HPMC-Cr) were studied. • Langmuir isotherm provided more fit and maximum adsorption capacity was 131.6 mg/g. • The adsorption process was chemisorption, controlled by intra-particle diffusion and film diffusion. • Adsorption is fast, stable, spontaneous and endothermic. - Abstract: A low-cost anion adsorbent for Cr(VI) effectively removing was synthesized by hyperbranched polyamide modified corncob (HPMC). Samples were characterized by Brunauer–Emmett–Teller (BET) surface area analysis, field-emission scanning electron microscopy (FE-SEM) with energy-dispersive X-ray spectroscopy, Fourier transform infrared (FTIR) and zeta potential analysis. Kinetics, isotherms and thermodynamics studies of HPMC for Cr(VI) adsorption were investigated in batch static experiments, in the temperature range of 25–45 °C, pH = 2.0. Results showed that the adsorption was rapid and stable, with the uptake capacity higher than 80% after 30 min. Adsorption behavior and rate-controlling mechanisms were analyzed using three kinetic models (pseudo-first order, pseudo-second order, intra-particle kinetic model). Kinetic studies showed that the adsorption of HPMC to Cr(VI) relied the pseudo-second-order model, and controlled both by the intra-particle diffusion and film diffusion. Equilibrium data was tested by Langmuir and Freundlich adsorption isotherm models. Langmuir model was more suitable to indicate a homogeneous distribution of active sites on HPMC and monolayer adsorption. The maximum adsorption capacity from the Langmuir model, q{sub max}, was 131.6 mg/g at pH 2.0 and 45 °C for HPMC. Thermodynamic parameters revealed spontaneous and endothermic nature of the Cr(VI) adsorption onto HPMC.

  8. Effect of acidic aqueous solution on chemical and physical properties of polyamide NF membranes

    Science.gov (United States)

    Jun, Byung-Moon; Kim, Su Hwan; Kwak, Sang Kyu; Kwon, Young-Nam

    2018-06-01

    This work was systematically investigated the effects of acidic aqueous solution (15 wt% sulfuric acid as model wastewater from smelting process) on the physical and chemical properties of commercially available nanofiltration (NF) polyamide membranes, using piperazine (PIP)-based NE40/70 membranes and m-phenylene diamine (MPD)-based NE90 membrane. Surface properties of the membranes were studied before and after exposure to strong acid using various analytical tools: Scanning Electron Microscopy (SEM), Attenuated Total Reflectance-Fourier Transform Infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS), contact angle analyzer, and electrophoretic light scattering spectrophotometer. The characterization and permeation results showed piperazine-based NE40/70 membranes have relatively lower acid-resistance than MPD-based NE90 membrane. Furthermore, density functional theory (DFT) calculation was also conducted to reveal the different acid-tolerances between the piperazine-based and MPD-based polyamide membranes. The easiest protonation was found to be the protonation of oxygen in piperazine-based monomer, and the N-protonation of the monomer had the lowest energy barrier in the rate determining step (RDS). The calculations were well compatible with the surface characterization results. In addition, the energy barrier in RDS is highly correlated with the twist angle (τD), which determines the delocalization of electrons between the carbonyl πCO bond and nitrogen lone pair, and the tendency of the twist angle was also maintained in longer molecules (dimer and trimer). This study clearly explained why the semi-aromatic membrane (NE40/70) is chemically less stable than the aromatic membrane (NE90) given the surface characterizations and DFT calculation results.

  9. Novel thermoplastic vulcanizates (TPVs based on silicone rubber and polyamide exploring peroxide cross-linking

    Directory of Open Access Journals (Sweden)

    K. Naskar

    2014-04-01

    Full Text Available Novel thermoplastic vulcanizates (TPVs based on silicone rubber (PDMS and polyamide (PA12 have been prepared by dynamic vulcanization process. The effect of dynamic vulcanization and influence of various types of peroxides as cross-linking agents were studied in detail. All the TPVs were prepared at a ratio of 50/50 wt% of silicone rubber and polyamide. Three structurally different peroxides, namely dicumyl peroxide (DCP, 3,3,5,7,7-pentamethyl 1,2,4-trioxepane (PMTO and cumyl hydroperoxide (CHP were taken for investigation. Though DCP was the best option for curing the silicone rubber, at high temperature it suffers from scorch safety. An inhibitor 2,2,6,6-tetramethylpiperidinyloxyl (TEMPO was added with DCP to stabilize the radicals in order to increase the scorch time. Though CHP (hydroperoxide had higher half life time than DCP at higher temperature, it has no significant effect on cross-linking of silicone rubber. PMTO showed prolonged scorch safety and better cross-linking efficiency rather than the other two. TPVs of DCP and PMTO were made up to 11 minutes of mixing. Increased values of tensile strength and elongation at break of PMTO cross-linked TPV indicate the superiority of PMTO. Scanning electron micrographs correlate with mechanical properties of the TPVs. High storage modulus (E' and lower loss tangent value of the PMTO cross-linked TPV indicate the higher degree of cross-linking which is also well supported by the overall cross-link density value. Thus PMTO was found to be the superior peroxide for cross-linking of silicone rubber at high temperature.

  10. Free Radical Scavenging Activity and Anthocyanin Profile of Cabernet Sauvignon Wines from the Balkan Region

    Directory of Open Access Journals (Sweden)

    Blaga Radovanović

    2010-06-01

    Full Text Available The present study is focused on anthocyanin derivatives characterizing the antioxidant activity of Cabernet Sauvignon wines produced from different vineyard regions in the Balkans. These bioactive compounds were quantified with a high performance liquid chromatography (HPLC-diode array detection (DAD method. The antiradical activity was estimated by the ability of the wine to scavenge the stable 2,2`-diphenyl-1-picrylhydrazyl free radical (DPPH·. The results show that the total anthocyanin content varied from 205.88 to 1940.28 mg/L, depending on agroclimatic factors and the enological practices of the corresponding vineyard region. The most prominent antocyanin in all investigated Cabernet Sauvignon wines was malvidin-3-O-monoglucoside, which accounted for 50.57% of total content, followed by its acetyl derivatives, 15.45%, and p-coumaryl derivatives 5.66%. The relationship between the anthocyanin derivatives and free radical scavenging activity is discussed. A high correlation between total anthocyanin content and DPPH· scavenging ability of tested wines was confirmed (r2 = 0.9619. The significant correlations were obtained between antiradical activity and the sum of 3-monoglucoside (r2 = 0.95594, the sum of 3-acetyl-3-glucoside (r2 = 0.9728 and the sum of p-coumaryl-3-glucoside (r2 = 0.8873 of wine samples. It can be concluded that, the anthocyanin composition can be used as biochemical marker for the authenticity of red grape cultivar and their corresponding single-cultivar wine.

  11. Free Radical Scavenging and Cellular Antioxidant Properties of Astaxanthin.

    Science.gov (United States)

    Dose, Janina; Matsugo, Seiichi; Yokokawa, Haruka; Koshida, Yutaro; Okazaki, Shigetoshi; Seidel, Ulrike; Eggersdorfer, Manfred; Rimbach, Gerald; Esatbeyoglu, Tuba

    2016-01-14

    Astaxanthin is a coloring agent which is used as a feed additive in aquaculture nutrition. Recently, potential health benefits of astaxanthin have been discussed which may be partly related to its free radical scavenging and antioxidant properties. Our electron spin resonance (ESR) and spin trapping data suggest that synthetic astaxanthin is a potent free radical scavenger in terms of diphenylpicryl-hydrazyl (DPPH) and galvinoxyl free radicals. Furthermore, astaxanthin dose-dependently quenched singlet oxygen as determined by photon counting. In addition to free radical scavenging and singlet oxygen quenching properties, astaxanthin induced the antioxidant enzyme paroxoanase-1, enhanced glutathione concentrations and prevented lipid peroxidation in cultured hepatocytes. Present results suggest that, beyond its coloring properties, synthetic astaxanthin exhibits free radical scavenging, singlet oxygen quenching, and antioxidant activities which could probably positively affect animal and human health.

  12. Performance of Chickens under Semi-scavenging Conditions: A ...

    African Journals Online (AJOL)

    Performance of Chickens under Semi-scavenging Conditions: A Case Study of ... per household was lost per year due to diseases, predators, accidents, and theft. ... as well as chicken house construction so as to avoid the risks of predators.

  13. Nitric oxide radical scavenging potential of some Elburz medicinal ...

    African Journals Online (AJOL)

    ONOS

    2010-08-09

    Aug 9, 2010 ... NO is also implicated in inflammation and other pathological ... adhesion and prevention of smooth muscle cell prolife- ... reduce NO levels is making use of NO scavengers. For ..... human nutrition and health are considerable.

  14. Antimicrobial and free radical scavenging activities of five ...

    African Journals Online (AJOL)

    Extracts from five indigenous Palestinian medicinal plants including Rosmarinus officinalis, Pisidium guajava, Punica granatum peel, grape seeds and Teucrium polium were investigated for antimicrobial and free radical scavenging activities against eight microorganisms, using well diffusion method. The microorganisms ...

  15. Shark scavenging behavior in the presence of competition

    Directory of Open Access Journals (Sweden)

    Shannon P. GERRY, Andrea J. SCOTT

    2010-02-01

    Full Text Available The distribution of organisms within a community can often be determined by the degree of plasticity or degree of specialization of resource acquisition. Resource acquisition is often based on the morphology of an organism, behavior, or a combination of both. Performance tests of feeding can identify the possible interactions that allow one species to better exploit a prey item. Scavenging behaviors in the presence or absence of a competitor were investigated by quantifying prey selection in a trophic generalist, spiny dogfish Squalus acanthias, and a trophic specialist, smooth-hounds Mustelus canis, in order to determine if each shark scavenged according to its jaw morphology. The diet of dogfish consists of small fishes, squid, ctenophores, and bivalves; they are expected to be nonselective predators. Smooth-hounds primarily feed on crustaceans; therefore, they are predicted to select crabs over other prey types. Prey selection was quantified by ranking each prey item according to the order it was consumed. Dietary shifts were analyzed by comparing the percentage of each prey item selected during solitary versus competitive scavenging. When scavenging alone, dogfish prefer herring and squid, which are easily handled by the cutting dentition of dogfish. Dogfish shift their diet to include a greater number of prey types when scavenging with a competitor. Smooth-hounds scavenge on squid, herring, and shrimp when alone, but increase the number of crabs in the diet when scavenging competitively. Competition causes smooth-hounds to scavenge according to their jaw morphology and locomotor abilities, which enables them to feed on a specialized resource [Current Zoology 56 (1: 100–108 2010].

  16. Bergenin Content and Free Radical Scavenging Activity of Bergenia Extracts. .

    Science.gov (United States)

    Hendrychová, Helena; Martin, Jan; Tůmová, Lenka; Kočevar-Glavač, Nina

    2015-07-01

    Our research was focused on the evaluation of bergenin content and free radical scavenging activity of extracts prepared from three different species of Bergenia - B. crassifolia (L.) Fritsch., B. ciliata (Haw.) Sternb. and B. x ornata Stein. collected during different seasons. Using an HPLC method, the highest total amount of bergenin was revealed in the leaves of B. x ornata and B. crassifolia (4.9 - 5.1 mg x g(-1)). Free radical scavenging power was determined by two methods--FRAP and NADH. The best free radical scavengers were B. crassifolia (FRAP: 6.7 - 15.9 mg GAE. 100g(-1); NADH: 20.3 - 50.9%) and B. ornata (FRAP: 13.7 - 15.2 mg GAE. 100g(-1); NADH: 29.3 - 31.1%). The lowest content of bergenin and the weakest radical scavenger was B. ciliata (bergenin: 3.1 mg x g(-1); FRAP: 5.5 - 11.0 mg GAE.100g(-1); NADH: 23.2 - 25.6%). The presence of a large percentage of bergenin is responsible for the radical scavenging activity, as shown by the results from the FRAP and NADH assays. Significant, positive correlation was found between bergenin content and radical scavenging activity in both methods.

  17. Weight savings in aerospace vehicles through propellant scavenging

    Science.gov (United States)

    Schneider, Steven J.; Reed, Brian D.

    1988-01-01

    Vehicle payload benefits of scavenging hydrogen and oxygen propellants are addressed. The approach used is to select a vehicle and a mission and then select a scavenging system for detailed weight analysis. The Shuttle 2 vehicle on a Space Station rendezvous mission was chosen for study. The propellant scavenging system scavenges liquid hydrogen and liquid oxygen from the launch propulsion tankage during orbital maneuvers and stores them in well insulated liquid accumulators for use in a cryogenic auxiliary propulsion system. The fraction of auxiliary propulsion propellant which may be scavenged for propulsive purposes is estimated to be 45.1 percent. The auxiliary propulsion subsystem dry mass, including the proposed scavenging system, an additional 20 percent for secondary structure, an additional 5 percent for electrical service, a 10 percent weight growth margin, and 15.4 percent propellant reserves and residuals is estimated to be 6331 kg. This study shows that the fraction of the on-orbit vehicle mass required by the auxiliary propulsion system of this Shuttle 2 vehicle using this technology is estimated to be 12.0 percent compared to 19.9 percent for a vehicle with an earth-storable bipropellant system. This results in a vehicle with the capability of delivering an additional 7820 kg to the Space Station.

  18. An illicit economy: scavenging and recycling of medical waste.

    Science.gov (United States)

    Patwary, Masum A; O'Hare, William Thomas; Sarker, M H

    2011-11-01

    This paper discusses a significant illicit economy, including black and grey aspects, associated with medical waste scavenging and recycling in a megacity, considering hazards to the specific group involved in scavenging as well as hazards to the general population of city dwellers. Data were collected in Dhaka, Bangladesh, using a variety of techniques based on formal representative sampling for fixed populations (such as recycling operatives) and adaptive sampling for roaming populations (such as scavengers). Extremely hazardous items (including date expired medicines, used syringes, knives, blades and saline bags) were scavenged, repackaged and resold to the community. Some HCE employees were also observed to sell hazardous items directly to scavengers, and both employees and scavengers were observed to supply contaminated items to an informal plastics recycling industry. This trade was made possible by the absence of segregation, secure storage and proper disposal of medical waste. Corruption, a lack of accountability and individual responsibility were also found to be contributors. In most cases the individuals involved with these activities did not understand the risks. Although motivation was often for personal gain or in support of substance abuse, participants sometimes felt that they were providing a useful service to the community. Copyright © 2011 Elsevier Ltd. All rights reserved.

  19. Weight savings in aerospace vehicles through propellant scavenging

    Science.gov (United States)

    Schneider, Steven J.; Reed, Brian D.

    1988-05-01

    Vehicle payload benefits of scavenging hydrogen and oxygen propellants are addressed. The approach used is to select a vehicle and a mission and then select a scavenging system for detailed weight analysis. The Shuttle 2 vehicle on a Space Station rendezvous mission was chosen for study. The propellant scavenging system scavenges liquid hydrogen and liquid oxygen from the launch propulsion tankage during orbital maneuvers and stores them in well insulated liquid accumulators for use in a cryogenic auxiliary propulsion system. The fraction of auxiliary propulsion propellant which may be scavenged for propulsive purposes is estimated to be 45.1 percent. The auxiliary propulsion subsystem dry mass, including the proposed scavenging system, an additional 20 percent for secondary structure, an additional 5 percent for electrical service, a 10 percent weight growth margin, and 15.4 percent propellant reserves and residuals is estimated to be 6331 kg. This study shows that the fraction of the on-orbit vehicle mass required by the auxiliary propulsion system of this Shuttle 2 vehicle using this technology is estimated to be 12.0 percent compared to 19.9 percent for a vehicle with an earth-storable bipropellant system. This results in a vehicle with the capability of delivering an additional 7820 kg to the Space Station.

  20. Increasing the Thermal Conductivity of Graphene-Polyamide-6,6 Nanocomposites by Surface-Grafted Polymer Chains: Calculation with Molecular Dynamics and Effective-Medium Approximation.

    Science.gov (United States)

    Gao, Yangyang; Müller-Plathe, Florian

    2016-02-25

    By employing reverse nonequilibrium molecular dynamics simulations in a full atomistic resolution, the effect of surface-grafted chains on the thermal conductivity of graphene-polyamide-6.6 (PA) nanocomposites has been investigated. The interfacial thermal conductivity perpendicular to the graphene plane is proportional to the grafting density, while it first increases and then saturates with the grafting length. Meanwhile, the intrinsic in-plane thermal conductivity of graphene drops sharply as the grafting density increases. The maximum overall thermal conductivity of nanocomposites appears at an intermediate grafting density because of these two competing effects. The thermal conductivity of the composite parallel to the graphene plane increases with the grafting density and grafting length which is attributed to better interfacial coupling between graphene and PA. There exists an optimal balance between grafting density and grafting length to obtain the highest interfacial and parallel thermal conductivity. Two empirical formulas are suggested, which quantitatively account for the effects of grafting length and density on the interfacial and parallel thermal conductivity. Combined with effective medium approximation, for ungrafted graphene in random orientation, the model overestimates the thermal conductivity at low graphene volume fraction (f 10%). For unoriented grafted graphene, the model matches the experimental results well. In short, this work provides some valuable guides to obtain the nanocomposites with high thermal conductivity by grafting chain on the surface of graphene.

  1. Synthesis and characterization of novel polyamide-ethers based on bis-imidazole containing bulky aryl pendant groups

    Directory of Open Access Journals (Sweden)

    Seyed Mahdi Saadati

    2013-01-01

    Full Text Available A series of novel polyamide-ethers (PAEs based on bis-imidazole containing bulky aryl pendant groups was prepared by direct polycondensation of a diamine, 4-(1-(4-(4-(2-(4-aminophenyl-4,5-diphenyl-1H-imidazol-1-ylphenoxyphenyl-4,5-diphenyl-1H-imidazol-2-ylbenzenamine (DABI, and various dicarboxylic acids. All the resulting polyamide-ethers were amorphous with inherent viscosities ranged from 0.52 to 0.61 dL/g and were readily soluble in many organic solvents which could be solution-cast into transparent and tough films. The glass transition temperatures (Tg of these polymers were affected considerably by their chemical structure and ranged from 230 to 310 ºC. They had useful levels of thermal stability associated with relatively high temperatures of 10% weight loss (T10 in the range of 329-399 ºC in air atmosphere.

  2. Extraction and Characterization of Natural Dye from Green Walnut Shells and Its Use in Dyeing Polyamide: Focus on Antibacterial Properties

    Directory of Open Access Journals (Sweden)

    Mohammad Mirjalili

    2013-01-01

    Full Text Available Extraction of dyes from walnut using Soxhlet apparatus has been studied. The color components extracted and isolated from walnut shells were characterized by column chromatography, thin layer chromatography (TLC, nuclear magnetic resonance (NMR, mass spectroscopy (MS, and infrared (IR techniques. Natural dye extract obtained from the walnut was used in dyeing polyamide fabrics with different mordants. The dyed fabrics were evaluated for antibacterial activity against pathogenic strains of Gram-positive (Staphylococcus aureus and Gram-negative (Escherichia coli bacteria. As such, the relationship between antibacterial activity and dye concentration is investigated. Durability of antibacterial activity to laundering is also discussed. Results indicate that the polyamide dyed with walnut displayed excellent antibacterial activity in the presence of ferric sulfate, cupric sulfate, and potassium aluminum sulfate and exhibited good and durable fastness properties.

  3. Electron scavenging in ethylene glycol-water glass at 4 and 77 K: scavenging of trapped vs mobile electrons. [. gamma. -rays, x radiation

    Energy Technology Data Exchange (ETDEWEB)

    Lin, D P; Kevan, L [Wayne State Univ., Detroit, Mich. (USA). Dept. of Chemistry; Steen, H B

    1976-01-01

    Electron scavenging efficiencies have been measured at 77 and 4 K in ethylene glycol-water glass for the following scavengers which span a 250-fold range of scavenger efficiencies at 77 K: HCl, NaNO/sub 3/ and K/sub 2/Cr0/sub 4/. The range of scavenging efficiencies decreases to 62 at 4 K with the largest relative change occurring for the less efficient scavengers. These results are suggested to be most consistent with a model in which scavenging occurs by tunneling from shallowly and deeply trapped electrons at 4 and 77 K, respectively.

  4. Highly Hydrophilic Thin-Film Composite Forward Osmosis Membranes Functionalized with Surface-Tailored Nanoparticles

    KAUST Repository

    Tiraferri, Alberto

    2012-09-26

    Thin-film composite polyamide membranes are state-of-the-art materials for membrane-based water purification and desalination processes, which require both high rejection of contaminants and high water permeabilities. However, these membranes are prone to fouling when processing natural waters and wastewaters, because of the inherent surface physicochemical properties of polyamides. The present work demonstrates the fabrication of forward osmosis polyamide membranes with optimized surface properties via facile and scalable functionalization with fine-tuned nanoparticles. Silica nanoparticles are coated with superhydrophilic ligands possessing functional groups that impart stability to the nanoparticles and bind irreversibly to the native carboxyl moieties on the membrane selective layer. The tightly tethered layer of nanoparticles tailors the surface chemistry of the novel composite membrane without altering the morphology or water/solute permeabilities of the membrane selective layer. Surface characterization and interfacial energy analysis confirm that highly hydrophilic and wettable membrane surfaces are successfully attained. Lower intermolecular adhesion forces are measured between the new membrane materials and model organic foulants, indicating the presence of a bound hydration layer at the polyamide membrane surface that creates a barrier for foulant adhesion. © 2012 American Chemical Society.

  5. New polyamides based on 1,3-bis(4-carboxy phenoxy propane and hydantoin derivatives: synthesis and properties

    Directory of Open Access Journals (Sweden)

    Khalil Faghihi

    2010-04-01

    Full Text Available Six new polyamides 5a-f containing flexible trimethylene segments in the main chain were synthesized through the direct polycondensation reaction of 1,3-bis(4-carboxy phenoxy propane 3 with six derivatives of hydantoins 5a-f in a medium consisting of N-methyl-2-pyrrolidone, triphenyl phosphite, calcium chloride and pyridine. The polycondensation reaction produced a series of novel polyamides in high yield with inherent viscosities between 0.30-0.47 dL/g. The resulted polymers were fully characterized by means of FT-IR, 1H-NMR spectroscopy, elemental analyses, inherent viscosity, solubility tests and gel permeation chromatography (GPC. Thermal properties of these polymers were investigated by using thermal gravimetric analysis (TGA and differential thermal gravimetry (DTG. The glass-transition temperatures of these polyamides were recorded between 130 and 155 oC by differential scanning calorimetry (DSC, and the 5% weight loss temperatures were ranging from 325 to 415 oC under nitrogen. 1,3-bis(4-Carboxy phenoxy propane 3 was prepared from the reaction of 4-hydroxy benzoic acid 1 with 1,3-dibromo propane 2 in the presence of NaOH solution.

  6. Effect of fiber content on flexural properties of glass fiber-reinforced polyamide-6 prepared by injection molding.

    Science.gov (United States)

    Nagakura, Manamu; Tanimoto, Yasuhiro; Nishiyama, Norihiro

    2017-07-26

    The use of non-metal clasp denture (NMCD) materials may seriously affect the remaining tissues because of the low rigidity of NMCD materials such as polyamides. The purpose of this study was to develop a high-rigidity glass fiber-reinforced thermoplastic (GFRTP) composed of E-glass fiber and polyamide-6 for NMCDs using an injection molding. The reinforcing effects of fiber on the flexural properties of GFRTPs were investigated using glass fiber content ranging from 0 to 50 mass%. Three-point bending tests indicated that the flexural strength and elastic modulus of a GFRTP with a fiber content of 50 mass% were 5.4 and 4.7 times higher than those of unreinforced polyamide-6, respectively. The result showed that the physical characteristics of GFRTPs were greatly improved by increasing the fiber content, and the beneficial effects of fiber reinforcement were evident. The findings suggest that the injection-molded GFRTPs are adaptable to NMCDs because of their excellent mechanical properties.

  7. Effect of ultraviolet light irradiation and sandblasting treatment on bond strengths between polyamide and chemical-cured resin.

    Science.gov (United States)

    Asakawa, Yuya; Takahashi, Hidekazu; Iwasaki, Naohiko; Kobayashi, Masahiro

    2014-01-01

    The aim of this study was to evaluate the effects of ultraviolet light (UV) irradiation and sandblasting treatment on the shear bond strength between polyamide and chemical-cured resin. Three types of commercial polyamides were treated using UV irradiation, sandblasting treatment, and a combining sandblasting and UV irradiation. The shear bond strength was measured and analyzed using the Kruskal-Wallis test (α=0.05). Comparing shear bond strengths without surface treatment, from 4.1 to 5.7 MPa, the UV irradiation significantly increased the shear bond strengths except for Valplast, whose shear bond strengths ranged from 5.2 to 9.3 MPa. The sandblasting treatment also significantly increased the shear bond strengths (8.0 to 11.4 MPa). The combining sandblasting and UV irradiation significantly increased the shear bond strengths (15.2 to 18.3 MPa) comparing without surface treatment. This combined treatment was considered the most effective at improving the shear bond strength between polyamide and chemical-cured resin.

  8. Silica-scavenging effects in ceria-based solid electrolytes

    Directory of Open Access Journals (Sweden)

    Ivanova, D.

    2008-08-01

    Full Text Available Composite materials based on gadolinium doped ceria (CGO with additions of silica, with both silica and lanthanum oxide, and with lanthanum silicate, were prepared by the conventional ceramic route, to assess the silica scavenging role of lanthanum oxide additions. Structural, microstructural and electrical characterization of these samples confirmed the formation of one apatite type lanthanum silicate-based phase from reaction of silica with lanthanum oxide. The formation of this phase occurred in parallel with a significant enhancement of the grain boundary conductivity of these composite materials. Further interaction between constituents, involving diffusion of La to CGO, and Ce and Gd to the apatite phase, had no significant consequences on the electrical performance of these materials. Overall, lanthanum oxide was shown to remove the siliceous phases from the grain boundaries of CGO.

    Se prepararon materiales compuestos basados en óxido de cerio dopado con gadolinio (TGO con adicciones de sílice, con sílice y óxido de lantano y silicato del lantano, mediante procesamiento cerámico convencional con objeto de confirmar el papel secuestrante de sílice de las adicciones. La caracterización estructural, microestructural y eléctrica de las muestras confirmó la formación de una fase tipo apatito basada en silicato de lantano a partir de la reacción de la sílice con el óxido de lantano. La formación de esta fase ocurre en paralelo con un incremento significativo de la conductividad a través del borde de grano de estos materiales. La interacción entre los constituyentes, incluyendo la difusión del La al CGO, y el Ce y el Gd a la fase apatito, no tiene consecuencias significativas sobre el comportamiento eléctrico de estos materiales. Resumiendo, el óxido de lantano es capaz de eliminar las fases silicias del borde de grano del CGO.

  9. Double-Layer Surface Modification of Polyamide Denture Base Material by Functionalized Sol-Gel Based Silica for Adhesion Improvement.

    Science.gov (United States)

    Hafezeqoran, Ali; Koodaryan, Roodabeh

    2017-09-21

    Limited surface treatments have been proposed to improve the bond strength between autopolymerizing resin and polyamide denture base materials. Still, the bond strength of autopolymerizing resins to nylon polymer is not strong enough to repair the fractured denture effectively. This study aimed to introduce a novel method to improve the adhesion of autopolymerizing resin to polyamide polymer by a double layer deposition of sol-gel silica and N-2-(aminoethyl)-3-aminopropyltrimethoxysilane (AE-APTMS). The silica sol was synthesized by acid-catalyzed hydrolysis of tetraethylorthosilicate (TEOS) as silica precursors. Polyamide specimens were dipped in TEOS-derived sol (TS group, n = 28), and exposed to ultraviolet (UV) light under O 2 flow for 30 minutes. UV-treated specimens were immersed in AE-APTMS solution and left for 24 hours at room temperature. The other specimens were either immersed in AE-APTMS solution (AP group, n = 28) or left untreated (NT group, n = 28). Surface characterization was investigated by fourier transform infrared spectroscopy (FTIR) and atomic force microscopy (AFM). Two autopolymerizing resins (subgroups G and T, n = 14) were bonded to the specimens, thermocycled, and then tested for shear bond strength with a universal testing machine. Data were analyzed with one-way ANOVA followed by Tukey's HSD (α = 0.05). FTIR spectra of treated surfaces confirmed the chemical modification and appearance of functional groups on the polymer. One-way ANOVA revealed significant differences in shear bond strength among the study groups. Tukey's HSD showed that TS T and TS G groups had significantly higher shear bond strength than control groups (p = 0.001 and p < 0.001, respectively). Moreover, bond strength values of AP T were statistically significant compared to controls (p = 0.017). Amino functionalized TEOS-derived silica coating is a simple and cost-effective method for improving the bond strength between the autopolymerizing resin and polyamide

  10. Synthesis and Free Radical Scavenging Activity of New Hydroxybenzylidene Hydrazines

    Directory of Open Access Journals (Sweden)

    Frantisek Sersen

    2017-05-01

    Full Text Available Hydroxybenzylidene hydrazines exhibit a wide spectrum of biological activities. Here, we report synthesis and free radical scavenging activity of nine new N-(hydroxybenzylidene-N′-[2,6-dinitro-4-(trifluoromethyl]phenylhydrazines. The chemical structures of these compounds were confirmed by 1H-NMR, 13C-NMR, 19F-NMR, IR spectroscopy, LC-MS, and elemental analysis. The prepared compounds were tested for their activity to scavenge 2,2-diphenyl-1-picrylhydrazyl (DPPH, galvinoxyl radical (GOR, and 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid (ABTS radicals. The free radical scavenging activity expressed as SC50 values of these compounds varied in a wide range, from a strong to no radical scavenging effect. The most effective radical scavengers were hydroxybenzylidene hydrazines containing three hydroxyl groups in the benzylidene part of their molecules. The prepared compounds were also tested for their activity to inhibit photosynthetic electron transport in spinach chloroplasts. IC50 values of these compounds varied in wide range, from an intermediate to no inhibitory effect.

  11. Synthesis and Free Radical Scavenging Activity of New Hydroxybenzylidene Hydrazines.

    Science.gov (United States)

    Sersen, Frantisek; Gregan, Fridrich; Kotora, Peter; Kmetova, Jarmila; Filo, Juraj; Loos, Dusan; Gregan, Juraj

    2017-05-29

    Hydroxybenzylidene hydrazines exhibit a wide spectrum of biological activities. Here, we report synthesis and free radical scavenging activity of nine new N-(hydroxybenzylidene)-N'-[2,6-dinitro-4-(trifluoromethyl)]phenylhydrazines. The chemical structures of these compounds were confirmed by 1H-NMR, 13C-NMR, 19F-NMR, IR spectroscopy, LC-MS, and elemental analysis. The prepared compounds were tested for their activity to scavenge 2,2-diphenyl-1-picrylhydrazyl (DPPH), galvinoxyl radical (GOR), and 2,2'-azino-bis(3-ethylbenzothiazoline)-6-sulphonic acid (ABTS) radicals. The free radical scavenging activity expressed as SC50 values of these compounds varied in a wide range, from a strong to no radical scavenging effect. The most effective radical scavengers were hydroxybenzylidene hydrazines containing three hydroxyl groups in the benzylidene part of their molecules. The prepared compounds were also tested for their activity to inhibit photosynthetic electron transport in spinach chloroplasts. IC50 values of these compounds varied in wide range, from an intermediate to no inhibitory effect.

  12. Multiple free-radical scavenging (MULTIS) capacity in cattle serum.

    Science.gov (United States)

    Sueishi, Yoshimi; Kamogawa, Erisa; Kimura, Anna; Kitahara, Go; Satoh, Hiroyuki; Asanuma, Taketoshi; Oowada, Shigeru

    2017-01-01

    Multiple free-radical scavenging (MULTIS) activity in cattle and human sera was evaluated with electron spin resonance spectroscopy. Scavenging rates against six active species, namely hydroxyl radical, superoxide anion, alkoxyl radical, alkylperoxyl radical, methyl radical, and singlet oxygen were quantified. The difference in the electron spin resonance signal intensity in the presence and absence of the serum was converted into the scavenging rates. Comparative MULTIS measurements were made in sera from eight beef cattle, three fetal calves and fifteen healthy human volunteers. Further, we determined the MULTIS value of albumin, the most abundant component in serum. MULTIS values in cattle sera indicated higher scavenging activity against most free radical species tested than human sera. In particular, cattle serum scavenging activities against superoxide and methyl radical were higher than human serum by 2.6 and 3.7 fold, respectively. In cattle serum, albumin appears to play a dominant role in MULTIS activity, but in human serum that is not the case. Previous data indicated that the abundance of uric acid in bovine blood is nearly 80% less than humans; however, this difference does not explain the deviation in MULTIS profile.

  13. Optimization of free radical scavenging capacity and pH of Hylocereus polyrhizus peel by Response Surface Methodology

    Science.gov (United States)

    Putranto, A. W.; Dewi, S. R.; Puspitasari, Y.; Nuriah, F. A.

    2018-03-01

    Red dragon fruit (Hylocereus polyrhizus) peel, a by-product of juice processing, contains a high antioxidant that can be used for nutraceuticals. Hence, it is important to extract and investigate its antioxidant stability. The aim of this study was to optimize the free radical scavenging capacity and pH of H. polyrhizus peel extract using Central Composite Design (CCD) under Response Surface Methodology (RSM). The extraction of H. polyrhizus peel was done by using green-Pulsed Electric Field (PEF)-assisted extraction method. Factors optimized were electric field strength (kV/cm) and extraction time (seconds). The result showed that the correlation between responses (free radical-scavenging capacity and pH) and two factors was quadratic model. The optimum conditions was obtained at the electric field strength of 3.96 kV/cm, and treatment time of 31.9 seconds. Under these conditions, the actual free radical-scavenging capacity and pH were 75.86 ± 0.2 % and 4.8, respectively. The verification model showed that the actual values are in accordance with the predicted values, and have error rate values of free radical-scavenging capacity and pH responses were 0.1% and 3.98%, respectively. We suggest to extract the H. polyrhizus peel using a green and non-thermal extraction technology, PEF-assisted extraction, for research, food applications and nutraceuticals industry.

  14. The Evolution of the Scavenger Receptor Cysteine-Rich Domain of the Class A Scavenger Receptors

    Directory of Open Access Journals (Sweden)

    Nicholas eYap

    2015-07-01

    Full Text Available The class A Scavenger Receptor (cA-SR family is a group of five evolutionarily related innate immune receptors. The cA-SRs are known for their promiscuous ligand binding; as they have been shown to bind bacteria such as Streptococcus pneumoniae, and Escherichia coli, as well as different modified forms of low-density lipoprotein. Three of the five family members possess a Scavenger Receptor Cysteine Rich (SRCR domain while the remaining two receptors lack the domain. Previous work has suggested that the Macrophage Associated Receptor with COllagenous structure (MARCO shares a recent common ancestor with the non-SRCR-containing receptors; however the origin of the SRCR domain within the cA-SRs remains unknown. We hypothesize that the SRCR domains of the cA-SRs have a common origin that predates teleost fish. Using the newly available sequence data from sea lamprey and ghost shark genome projects, we have shown that MARCO shares a common ancestor with the SRCR-containing proteins. In addition, we explored the evolutionary relationships within the SRCR domain by reconstructing the ancestral SRCR domains of the cA-SRs. We identified a motif that is highly conserved between the cA-SR SRCR domains and the ancestral SRCR domain that consist of WGTVCDD. We also show that the GRAEVYY motif, a functionally important motif within MARCO, is poorly conserved in the other cA-SRs and in the reconstructed ancestral domain. Further, we identified three sites within MARCO’s SRCR domain which are under positive selection. Two of these sites lie adjacent to the conserved WGTVCDD motif, and may indicate a potential biological function for these sites. Together these findings indicate a common origin of the SRCR domain within the cA-SRs; however different selective pressures between the proteins may have caused MARCOs SRCR domain to evolve to contain different functional motifs when compared to the other SRCR-containing cA-SRs.

  15. In vitro free radical scavenging activity of Ixora coccinea L

    Directory of Open Access Journals (Sweden)

    Moni Rani Saha

    2008-06-01

    Full Text Available Antioxidant activity of the methanol extract of Ixora coccinea L. was determined by DPPH free radical scavenging assay, reducing power and total antioxidant capacity using phosphomolybdenum method. Preliminary phytochemical screening revealed that the extract of the flower of I. coccinea possesses flavonoids, steroids and tannin materials. The extract showed significant activities in all antioxidant assays compared to the standard antioxidant in a dose dependent manner and remarkable activities to scavenge reactive oxygen species (ROS may be attributed to the high amount of hydrophilic phenolics. In DPPH radical scavenging assay the IC50 value of the extract was found to be 100.53 μg/mL while ascorbic acid had the IC50 value 58.92 μg/mL. Moreover, I. coccinea extract showed strong reducing power and total antioxidant capacity.

  16. Scavenging energy from human motion with tubular dielectric polymer

    Science.gov (United States)

    Jean-Mistral, Claire; Basrour, Skandar

    2010-04-01

    Scavenging energy from human motion is a challenge to supply low consumption systems for sport or medical applications. A promising solution is to use electroactive polymers and especially dielectric polymers to scavenge mechanical energy during walk. In this paper, we present a tubular dielectric generator which is the first step toward an integration of these structures into textiles. For a 10cm length and under a strain of 100%, the structure is able to scavenge 1.5μJ for a poling voltage of 200V and up to 40μJ for a poling voltage of 1000V. A 30cm length structure is finally compared to our previous planar structure, and the power management module for those structures is discussed.

  17. Free radical scavenging properties of some wine probes

    International Nuclear Information System (INIS)

    Stasko, A.; Liptakova, M.; Malik, F.

    1999-01-01

    There are preliminary results of investigation of scavenging properties of 8 probes of Slovak wines (consisting of one reference, 3 probes of white wine and 4 probes of red wine). According to the literature so far, wine probes contain paramagnetic species (Mn 2+ , characterised with sextet spectrum, and a singlet line around g=2,00). In our probes we observed Mn 2+ signals, but no significant evidence for a single line of free radical was found. We can conclude that Mn 2+ content in the red wines is generally higher than in the white ones. Further, we investigated the scavenging activities of the probes adding solution of dinitropicryl hydrazyl (DPPH-stable radical) to them. Their ability to terminate free radicals resulted in the decrease of the final DPPH concentrations in the probes. The red wines have significantly higher capability to scavenge free radicals than the probes of white wines. (authors)

  18. High throughput assay for evaluation of reactive carbonyl scavenging capacity.

    Science.gov (United States)

    Vidal, N; Cavaille, J P; Graziani, F; Robin, M; Ouari, O; Pietri, S; Stocker, P

    2014-01-01

    Many carbonyl species from either lipid peroxidation or glycoxidation are extremely reactive and can disrupt the function of proteins and enzymes. 4-hydroxynonenal and methylglyoxal are the most abundant and toxic lipid-derived reactive carbonyl species. The presence of these toxics leads to carbonyl stress and cause a significant amount of macromolecular damages in several diseases. Much evidence indicates trapping of reactive carbonyl intermediates may be a useful strategy for inhibiting or decreasing carbonyl stress-associated pathologies. There is no rapid and convenient analytical method available for the assessment of direct carbonyl scavenging capacity, and a very limited number of carbonyl scavengers have been identified to date, their therapeutic potential being highlighted only recently. In this context, we have developed a new and rapid sensitive fluorimetric method for the assessment of reactive carbonyl scavengers without involvement glycoxidation systems. Efficacy of various thiol- and non-thiol-carbonyl scavenger pharmacophores was tested both using this screening assay adapted to 96-well microplates and in cultured cells. The scavenging effects on the formation of Advanced Glycation End-product of Bovine Serum Albumin formed with methylglyoxal, 4-hydroxynonenal and glucose-glycated as molecular models were also examined. Low molecular mass thiols with an α-amino-β-mercaptoethane structure showed the highest degree of inhibitory activity toward both α,β-unsaturated aldehydes and dicarbonyls. Cysteine and cysteamine have the best scavenging ability toward methylglyoxal. WR-1065 which is currently approved for clinical use as a protective agent against radiation and renal toxicity was identified as the best inhibitor of 4-hydroxynonenal.

  19. High throughput assay for evaluation of reactive carbonyl scavenging capacity

    Directory of Open Access Journals (Sweden)

    N. Vidal

    2014-01-01

    Full Text Available Many carbonyl species from either lipid peroxidation or glycoxidation are extremely reactive and can disrupt the function of proteins and enzymes. 4-hydroxynonenal and methylglyoxal are the most abundant and toxic lipid-derived reactive carbonyl species. The presence of these toxics leads to carbonyl stress and cause a significant amount of macromolecular damages in several diseases. Much evidence indicates trapping of reactive carbonyl intermediates may be a useful strategy for inhibiting or decreasing carbonyl stress-associated pathologies. There is no rapid and convenient analytical method available for the assessment of direct carbonyl scavenging capacity, and a very limited number of carbonyl scavengers have been identified to date, their therapeutic potential being highlighted only recently. In this context, we have developed a new and rapid sensitive fluorimetric method for the assessment of reactive carbonyl scavengers without involvement glycoxidation systems. Efficacy of various thiol- and non-thiol-carbonyl scavenger pharmacophores was tested both using this screening assay adapted to 96-well microplates and in cultured cells. The scavenging effects on the formation of Advanced Glycation End-product of Bovine Serum Albumin formed with methylglyoxal, 4-hydroxynonenal and glucose-glycated as molecular models were also examined. Low molecular mass thiols with an α-amino-β-mercaptoethane structure showed the highest degree of inhibitory activity toward both α,β-unsaturated aldehydes and dicarbonyls. Cysteine and cysteamine have the best scavenging ability toward methylglyoxal. WR-1065 which is currently approved for clinical use as a protective agent against radiation and renal toxicity was identified as the best inhibitor of 4-hydroxynonenal.

  20. Multiple free-radical scavenging capacity in serum

    Science.gov (United States)

    Oowada, Shigeru; Endo, Nobuyuki; Kameya, Hiromi; Shimmei, Masashi; Kotake, Yashige

    2012-01-01

    We have developed a method to determine serum scavenging-capacity profile against multiple free radical species, namely hydroxyl radical, superoxide radical, alkoxyl radical, alkylperoxyl radical, alkyl radical, and singlet oxygen. This method was applied to a cohort of chronic kidney disease patients. Each free radical species was produced with a common experimental procedure; i.e., uv/visible-light photolysis of free-radical precursor/sensitizer. The decrease in free-radical concentration by the presence of serum was quantified with electron spin resonance spin trapping method, from which the scavenging capacity was calculated. There was a significant capacity change in the disease group (n = 45) as compared with the healthy control group (n = 30). The percent values of disease’s scavenging capacity with respect to control group indicated statistically significant differences in all free-radical species except alkylperoxyl radical, i.e., hydroxyl radical, 73 ± 12% (p = 0.001); superoxide radical, 158 ± 50% (p = 0.001); alkoxyl radical, 121 ± 30% (p = 0.005); alkylperoxyl radical, 123 ± 32% (p>0.1); alkyl radical, 26 ± 14% (p = 0.001); and singlet oxygen, 57 ± 18% (p = 0.001). The scavenging capacity profile was illustrated using a radar chart, clearly demonstrating the characteristic change in the disease group. Although the cause of the scavenging capacity change by the disease state is not completely understood, the profile of multiple radical scavenging capacities may become a useful diagnostic tool. PMID:22962529

  1. The Impact of Flight Hardware Scavenging on Space Logistics

    Science.gov (United States)

    Oeftering, Richard C.

    2011-01-01

    For a given fixed launch vehicle capacity the logistics payload delivered to the moon may be only roughly 20 percent of the payload delivered to the International Space Station (ISS). This is compounded by the much lower flight frequency to the moon and thus low availability of spares for maintenance. This implies that lunar hardware is much more scarce and more costly per kilogram than ISS and thus there is much more incentive to preserve hardware. The Constellation Lunar Surface System (LSS) program is considering ways of utilizing hardware scavenged from vehicles including the Altair lunar lander. In general, the hardware will have only had a matter of hours of operation yet there may be years of operational life remaining. By scavenging this hardware the program, in effect, is treating vehicle hardware as part of the payload. Flight hardware may provide logistics spares for system maintenance and reduce the overall logistics footprint. This hardware has a wide array of potential applications including expanding the power infrastructure, and exploiting in-situ resources. Scavenging can also be seen as a way of recovering the value of, literally, billions of dollars worth of hardware that would normally be discarded. Scavenging flight hardware adds operational complexity and steps must be taken to augment the crew s capability with robotics, capabilities embedded in flight hardware itself, and external processes. New embedded technologies are needed to make hardware more serviceable and scavengable. Process technologies are needed to extract hardware, evaluate hardware, reconfigure or repair hardware, and reintegrate it into new applications. This paper also illustrates how scavenging can be used to drive down the cost of the overall program by exploiting the intrinsic value of otherwise discarded flight hardware.

  2. Flame Retardant Polyamide Fibres: The Challenge of Minimising Flame Retardant Additive Contents with Added Nanoclays

    Directory of Open Access Journals (Sweden)

    Richard Horrocks

    2016-08-01

    Full Text Available This work shows that halogen-free, flame retarded polyamide 6 (PA6, fabrics may be produced in which component fibres still have acceptable tensile properties and low levels (preferably ≤10 wt % of additives by incorporating a nanoclay along with two types of flame retardant formulations. The latter include (i aluminium diethyl phosphinate (AlPi at 10 wt %, known to work principally in the vapour phase and (ii ammonium sulphamate (AS/dipentaerythritol (DP system present at 2.5 and 1 wt % respectively, believed to be condense phase active. The nanoclay chosen is an organically modified montmorillonite clay, Cloisite 25A. The effect of each additive system is analysed in terms of its ability to maximise both filament tensile properties relative to 100% PA6 and flame retardant behaviour of knitted fabrics in a vertical orientation. None of the AlPi-containing formulations achieved self-extinguishability, although the presence of nanoclay promoted lower burning and melt dripping rates. The AS/DP-containing formulations with total flame retardant levels of 5.5 wt % or less showed far superior properties and with nanoclay, showed fabric extinction times ≤ 39 s and reduced melt dripping. The tensile and flammability results, supported by thermogravimetric analysis, have been interpreted in terms of the mechanism of action of each flame retardant/nanoclay type.

  3. Preparation and characterisation of polyamide 11/montmorillonite (MMT) nanocomposites for use in angioplasty balloon applications

    International Nuclear Information System (INIS)

    Halim, Khairul Anwar A.; Farrell, Joseph B.; Kennedy, James E.

    2013-01-01

    With increased demands on catheter balloon functionality, there is an emphasis to blend new materials which can improve mechanical performance. Polymer nanocomposites were prepared by melt blending polyamide 11 (PA 11) with organically modified montmorillonite nanoclay. The effects of incorporating the nanoclay on the short-term mechanical properties of PA 11 were assessed using a design of experiments (DoEs) approach. X-ray diffraction (XRD), transmission electron microscopy (TEM), differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis techniques (DMA) were used to characterise the morphology of the nanocomposites. Design of experiments studies revealed that the optimum nanocomposites properties can be achieved by carefully controlling the melt compounding parameters. XRD and TEM data proved that exfoliated clay morphologies existed within the matrix at low clay loading (2%). Whereas the interaction between the polymer matrix and nanoclay was quantified in the DMA spectra, showed a significant increase in storage modulus (up to 80%). The reinforcing effect of nanoclay within the PA 11 was further investigated using mechanical testing, where significant increases in the ultimate tensile strength and strain at break of reinforced tri-layer balloon tubing were observed. - Highlights: • TEM reveals the coexistence of exfoliated and intercalated nanostructures. • Isothermal crystallisation studies found that the nano-clays reduced the crystallisation time. • Significant increase in the storage modulus was due to the reinforcing effect of the nano-clay platelets. • It was observed that the activation energy values decreased due to the presence of nanoclay

  4. Preparation and characterisation of polyamide 11/montmorillonite (MMT) nanocomposites for use in angioplasty balloon applications

    Energy Technology Data Exchange (ETDEWEB)

    Halim, Khairul Anwar A. [Department of Polymer Engineering, Athlone Institute of Technology, Athlone (Ireland); School of Materials Engineering, Universiti Malaysia Perlis, Perlis (Malaysia); Farrell, Joseph B. [Department of Polymer Engineering, Athlone Institute of Technology, Athlone (Ireland); Kennedy, James E., E-mail: jkennedy@ait.ie [Department of Polymer Engineering, Athlone Institute of Technology, Athlone (Ireland)

    2013-12-16

    With increased demands on catheter balloon functionality, there is an emphasis to blend new materials which can improve mechanical performance. Polymer nanocomposites were prepared by melt blending polyamide 11 (PA 11) with organically modified montmorillonite nanoclay. The effects of incorporating the nanoclay on the short-term mechanical properties of PA 11 were assessed using a design of experiments (DoEs) approach. X-ray diffraction (XRD), transmission electron microscopy (TEM), differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis techniques (DMA) were used to characterise the morphology of the nanocomposites. Design of experiments studies revealed that the optimum nanocomposites properties can be achieved by carefully controlling the melt compounding parameters. XRD and TEM data proved that exfoliated clay morphologies existed within the matrix at low clay loading (2%). Whereas the interaction between the polymer matrix and nanoclay was quantified in the DMA spectra, showed a significant increase in storage modulus (up to 80%). The reinforcing effect of nanoclay within the PA 11 was further investigated using mechanical testing, where significant increases in the ultimate tensile strength and strain at break of reinforced tri-layer balloon tubing were observed. - Highlights: • TEM reveals the coexistence of exfoliated and intercalated nanostructures. • Isothermal crystallisation studies found that the nano-clays reduced the crystallisation time. • Significant increase in the storage modulus was due to the reinforcing effect of the nano-clay platelets. • It was observed that the activation energy values decreased due to the presence of nanoclay.

  5. Synergistic Flame Retardancy of Aluminium Dipropylphosphinate and Melamine in Polyamide 6

    Directory of Open Access Journals (Sweden)

    Linsheng Tang

    2013-01-01

    Full Text Available The synergistic flame retardancy of aluminium dipropylphosphinate (ADPP and melamine (ME in polyamide 6 (PA6 was studied by the limiting oxygen index (LOI measurement, the vertical burning test, and the cone calorimeter test, and the mechanism was also discussed by thermogravimetric and residual analyses. The experimental results indicated that there was obvious synergistic flame retardancy between ADPP and ME under their appropriate weight ratios. The thermogravimetric results and the analysis of the residues obtained in cone calorimeter test showed that ADPP and ADPP/ME played the role of flame retardance by gaseous- and condensed-phase mechanisms, where, on one hand, they were decomposed into nonvolatile aluminum phosphate and promoted the carbonization of PA6, and the formed intumescent layer resulted in flame retardancy by the barrier effect on heat, air, and decomposition products, and on the other hand, they were decomposed into volatile phosphorus compounds which bring about flame retardancy by flame inhibition. Using a combination of ADPP and ME improved charring of PA6 and raised the residual rate of P and Al, thus, improving the barrier effect in the condensed phase.

  6. Study on thermal stability and chemical structure of polyamide blended with small amount of Cu

    International Nuclear Information System (INIS)

    Arai, Tsuyoshi; Ueno, Tomonaga; Kajiya, Takafumi; Ishikawa, Tomoyuki; Takeda, Kunihiko

    2007-01-01

    The thermal stability and the chemical structure of Polyamide 66 (PA66) blended with a small amount of copper have been studied. The thermal degradation of the blend with 35 ppm or more of copper was restrained and no strong influence of the concentration of copper was observed. The molecular weight of PA66 decreased by the thermal aging process but the amount of decrease of the blend was smaller than that of the non-blend. The water uptake of the blend increased. The chemical structure, which was observed by IR and NMR, changed slightly by blending with copper after aging at higher temperatures. Multiple items influenced the thermal stability of PA66 blended with a small amount of copper instead of just one. Namely, the main chain of PA66 is cut by heat and the degree of the cut is restrained by the copper. The diffusion time of copper atoms that disperse uniformly in the PA66 matrix is short enough to cover the individual amide groups and the effect enlarges the entire configuration of the PA66 chain to enhance the thermal stability. (author)

  7. Evaluation of the permeability of microporous membranes polyamide 6 / clay bentonite for water-oil separation

    International Nuclear Information System (INIS)

    Medeiros, P.S.S.; Medeiros, K.M.; Araujo, E.M.; Lira, H.L.

    2014-01-01

    The petroleum refining industries have faced major problems in relation to the treatment of their effluents before disposal into the environment. Among the conventional technologies treatment of these effluents, the process of oil-water separation by means of membranes has been extensively used, for having enormous potentiality. Therefore, in this study, hybrid membranes of polyamide 6/ bentonite clay were produced by the technique of phase inversion and by precipitation of the solution from the nanocomposites obtained by melt intercalation. The clay was organically modified with the quaternary ammonium salt (Cetremide®). The nanocomposites were obtained from (PA6) with untreated (AST) and treated clay (ACT), which were subsequently characterized by X-ray diffraction (XRD). Already membranes were characterized by XRD, scanning electron microscopy (SEM) and flow measurements. From the XRD results, it was observed an exfoliated and/or partially exfoliated structure for the nanocomposites and for the membranes. From SEM images it was observed that the presence of AST and ACT clays in the polymeric matrix caused changes in membrane morphology and pore formation. The flow with distilled water in the membranes showed a decrease initially and then followed by stability. All membranes tested in the process of separating emulsions of oil in water, particularly those of nanocomposites obtained a significant reduction of oil concentration in the permeate, thus showing that these membranes have a great potential to be applied to the water-oil separation. (author)

  8. Durability Characteristics Analysis of Plastic Worm Wheel with Glass Fiber Reinforced Polyamide.

    Science.gov (United States)

    Kim, Gun-Hee; Lee, Jeong-Won; Seo, Tae-Il

    2013-05-10

    Plastic worm wheel is widely used in the vehicle manufacturing field because it is favorable for weight lightening, vibration and noise reduction, as well as corrosion resistance. However, it is very difficult for general plastics to secure the mechanical properties that are required for vehicle gears. If the plastic resin is reinforced by glass fiber in the fabrication process of plastic worm wheel, it is possible to achieve the mechanical properties of metallic material levels. In this study, the mechanical characteristic analysis of the glass-reinforced plastic worm wheel, according to the contents of glass fiber, is performed by analytic and experimental methods. In the case of the glass fiber-reinforced resin, the orientation and contents of glass fibers can influence the mechanical properties. For the characteristic prediction of plastic worm wheel, computer-aided engineering (CAE) analysis processes such as structural and injection molding analysis were executed with the polyamide resin reinforcement glass fiber (25 wt %, 50 wt %). The injection mold for fabricating the prototype plastic worm wheel was designed and made to reflect the CAE analysis results. Finally, the durability of prototype plastic worm wheel fabricated by the injection molding process was evaluated by the experimental method and the characteristics according to the glass fiber contents.

  9. Generation of conductivity through transfer charge properties, for polyesters and polyamides with characteristic functional groups

    Science.gov (United States)

    Gonzalez, Carmen; Tagle, Luis Hernan; Terraza, Claudio A.; Barriga, Andres; Cabrera, A. L.; Volkmann, Ulrich G.

    2011-03-01

    Electro-optic properties of σ -conjugated polymers, as polysilylene; are associated with electron conjugation in the silicon atom, which allows a significant delocalization of electrons along of the chain. Thus, the conductivity is intimately connected to the mobility of charge carriers, which in turn depends on the structure and morphology of the system. We report the characterization of polyesters (PEFs) and polyamides (PAFs). Film thicknesses were obtained by ellipsometry. The vibration frequencies of the groups were determined by FT-IR and corroborated by Raman spectroscopy. Structural information was obtained from X-Ray diffraction (XRD). The structural and surface morphology were studied by scanning electron microscope (SEM). Electrical conductivity of the polymers was measured before and after exposure to iodine vapor, for films of different thicknesses. Morphological differentiation was studied by energy dispersive microscopy (EDX), showing a regular distribution of iodine within the polymer. Preliminary conductivity measurements showed adverse effects when oxidation of the polymer films is induced These effects are related to a certain grade of disorder within the system

  10. Preparation of Polyamide-6 Submicrometer-Sized Spheres by In Situ Polymerization.

    Science.gov (United States)

    Zhao, Xingke; Xia, Housheng; Fu, Xubing; Duan, Jianping; Yang, Guisheng

    2015-11-01

    Polyamide-6 (PA6) submicron-sized spheres are prepared by two steps: (1) anionic ring-opening polymerization of ε-caprolactam in the presence of poly(ethylene glycol)-block-poly-(propylene glycol)-block-poly(ethylene glycol)(PEG-b-PPG-b-PEG) and (2) separation of PA6 spheres by dissolving PEG-b-PPG-b-PEG from the prepared blends. The PA6 microspheres obtained are regular spherical, with diameter ranging from 200 nm to 2 μm and narrow size distribution, as confirmed by scanning electron microscopy. By comparison with PA6/PS and PA6/PEG systems, it is denominated that the PEG blocks in PEG-b-PPG-b-PEG can effectively reduce the surface tension of PA6 droplets and further decrease the diameter of the PA6 microspheres. The PPG block in PEG-b-PPG-b-PEG can prevent the PA6 droplets coalescing with each other, and isolated spherical particles can be obtained finally. The phase inversion of the PA6/PEG-b-PPG-b-PEG blends occurs at very low PEG-b-PPG-b-PEG content; the PEG-b-PPG-b-PEG phase can be removed by water easily. The whole experiment can be finished in a short time (approximately in half an hour) without using any organic solvents; it is an efficient strategy for the preparation of submicron-sized PA6 microspheres. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Natural organic matter interactions with polyamide and polysulfone membranes: Formation of conditioning film

    KAUST Repository

    Gutierrez, Leonardo

    2015-03-31

    A conditioning film changes the physicochemical properties of the membrane surface and strongly affects subsequent fouling behavior. Results from this Atomic Force Microscopy study indicate that Natural Organic Matter (NOM) characteristics, membrane surface properties, and solution chemistry are fundamental during conditioning film formation. Repulsive forces were observed between HUM (humic-NOM) and Polyamide (PA) or Polysulfone (PS) membranes during approach in Na+ and Ca2+ solutions. However, repulsive and attractive forces were randomly recorded during BIOP (biopolymer-NOM) approach to both membranes, possibly caused by low electrostatic repulsion, hydrogen bonding, and presence of chemically/physically heterogeneous regions on membrane surfaces. During retracting, Ca2+ ions increased HUM adhesion to PA and PS membrane, indicating cation bridging/complexation as dominant interacting mechanism for this isolate. BIOP adsorption on PS and PA membrane was stronger than HUM under similar solution conditions, where hydrogen bonding would play an important role. Additionally, irrespective of solution conditions, higher adhesion energy was recorded on PS than on PA membrane for both NOM isolates, indicating membrane hydrophobicity as an important interacting factor. Results from this research will advance our understanding of conditioning film formation for NOM isolates and membranes of different physicochemical characteristics.

  12. Diffuse plasma treatment of polyamide 66 fabric in atmospheric pressure air

    International Nuclear Information System (INIS)

    Li, Lee; Peng, Ming-yang; Teng, Yun; Gao, Guozhen

    2016-01-01

    Graphical abstract: - Highlights: • A cylindrical-electrode nanosecond-pulse diffuse-discharge reactor is presented. • Large-scale non-thermal plasmas were generated steadily in atmospheric air. • Treated PA66 fabric is etched with oxygen-containing group increases. • The hydrophily of treated PA66 fabric improves effectively. • Extending the treatment time is a method to reduce the treatment frequency. - Abstract: The polyamide 66 (PA66) fabrics are hard to be colored or glued in industrial production due to the poor hydrophily. Diffuse plasma is a kind of non-thermal plasma generated at atmospheric pressure in air. This paper proposes that large-scale diffuse plasma generated between wire electrodes can be employed for improving the hydrophily of PA66 fabrics. A repetitive nanosecond-pulse diffuse-discharge reactor using a cylindrical wire electrode configuration is presented, which can generate large-scale non-thermal plasmas steadily at atmospheric pressure without any barrier dielectric. Then the reactor is used to treat PA66 fabrics in different discharge conditions. The hydrophilicity property of modified PA66 is measured by wicking test method. The modified PA66 is also analyzed by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) to prove the surface changes in physical microstructure and chemical functional groups, respectively. What's more, the effects of treatment time and treatment frequency on surface modification are investigated and discussed.

  13. Chlorine-Resistant Polyamide Reverse Osmosis Membrane with Monitorable and Regenerative Sacrificial Layers.

    Science.gov (United States)

    Huang, Hai; Lin, Saisai; Zhang, Lin; Hou, Li'an

    2017-03-22

    Improving chlorine stability is a high priority for aromatic polyamide (PA) reverse osmosis (RO) membranes especially in long-term desalination. In this Research Article, PA RO membranes of sustainable chlorine resistance was synthesized. Glycylglycine (Gly) was grafted onto the membrane surface as a regenerative chlorine sacrificial layer, and the zeta-potential was used to monitor the membrane performance and to conduct timely regeneration operations for chlorinated Gly. The Gly-grafted PA membrane exhibited ameliorative chlorine resistance in which the N-H moiety of glycylglycine served as sacrificial pendants against chlorine attacks. Cyclic chlorination experiments, combined with FT-IR and XPS analysis, were carried out to characterize the membrane. Results indicated that the resulting N-halamines could be fast regenerated by a simple alkaline reduction step (pH 10). A synchronous relationship between the zeta-potential and the chlorination extent of the sacrificial layer was observed. This indicated that the zeta-potential can be used as an on-site sensor to conduct a timely regeneration operation. The intrinsic mechanism of the surface sacrificial process was also studied.

  14. Reinforced nanohydroxyapatite/polyamide66 scaffolds by chitosan coating for bone tissue engineering.

    Science.gov (United States)

    Huang, Di; Zuo, Yi; Zou, Qin; Wang, Yanying; Gao, Shibo; Wang, Xiaoyan; Liu, Haohuai; Li, Yubao

    2012-01-01

    High porosity of scaffold is always accompanied by poor mechanical property; the aim of this study was to enhance the strength and modulus of the highly porous scaffold of nanohydroxyapatite/polyamide66 (n-HA/PA66) by coating chitosan (CS) and to investigate the effect of CS content on the scaffold physical properties and cytological properties. The results show that CS coating can reinforce the scaffold effectively. The compress modulus and strength of the CS coated n-HA/PA66 scaffolds are improved to 32.71 and 2.38 MPa, respectively, being about six times and five times of those of the uncoated scaffolds. Meanwhile, the scaffolds still exhibit a highly interconnected porous structure and the porosity is approximate about 78%, slightly lower than the value (84%) of uncoated scaffold. The cytological properties of scaffolds were also studied in vitro by cocultured with osteoblast-like MG63 cells. The cytological experiments demonstrate that the reinforced scaffolds display favorable cytocompatibility and have no significant difference with the uncoated n-HA/PA66 scaffolds. The CS reinforced n-HA/PA66 scaffolds can meet the basic mechanical requirement of bone tissue engineering scaffold, presenting a potential for biomedical application in bone reconstruction and repair. Copyright © 2011 Wiley Periodicals, Inc.

  15. Viscosity of nanoconfined polyamide-6,6 oligomers: atomistic reverse nonequilibrium molecular dynamics simulation.

    Science.gov (United States)

    Eslami, Hossein; Müller-Plathe, Florian

    2010-01-14

    Our new simulation scheme in isosurface-isothermal-isobaric ensemble [Eslami, H.; Mozaffari, F.; Moghadasi, J.; Müller-Plathe, F. J. Chem. Phys. 2008, 129, 194702], developed to simulate confined fluids in equilibrium with bulk, is applied to simulate polyamide-6,6 oligomers confined between graphite surfaces. The reverse nonequilibrium molecular dynamics simulation technique is employed to shear the graphite surfaces. In this work, six confined systems, with different surface separations, as well as the bulk fluid are simulated. Our results show a viscosity increase with respect to the bulk fluid, with decreasing distance between surfaces. Also, the calculated viscosities of the confined systems show an oscillatory behavior with maxima corresponding to well-formed layers between the surfaces. We observe a substantial slip at the surfaces, with the slip length depending on the shear rate and on the slit width. The slip length and the slip velocity show oscillatory behavior with out-of-phase oscillations with respect to the solvation force oscillations. Moreover, the temperature difference between coldest and hottest parts of the simulation box depends on the shear rate and on the layering effect (solvation force oscillations). An analysis of oligomer deformation under flow shows preferential alignment of oligomers parallel to the surfaces with increasing shear rate.

  16. Microporous membranes from polyamide 6/national clay nanocomposites - Part 2: microstructural and permeability evaluation

    International Nuclear Information System (INIS)

    Leite, Amanda M.D.; Araujo, Edcleide M.; Lira, Helio de L.; Paz, Rene Anisio da; Medeiros, Vanessa da Nobrega

    2014-01-01

    Organic/inorganic hybrid membranes of polyamide 6 and mineral clay containing layers of silicate were prepared and compared to those of the pure polymer. Use was made of an as-received sodium clay from industry and another organophilized with ammonium quaternary salts (Dodigen and Cetremide). The salts make the clays surface hydrophobic and improve their incorporation into the polymer matrix in the molten state. Membranes were prepared with these nanocomposites using the immersion-precipitation technique with formic acid as a solvent, and precipitation in a water bath as non-solvent. The acid concentration in the solution containing the polymer and the hybrids was varied to study its influence in morphology and permeability of the membranes. An asymmetric morphology consisting of a filter skin and a porous support was observed, with pores both on the surface and in the cross section being affected by the different salts. This asymmetric morphology was also affected significantly by the acid concentration, with thicker filter skins for higher concentrations. The acid concentration affected the pores size and their distribution. The clay particles probably acted as a barrier to the flow. The permeating flux for the two acid concentrations varied as a function of the distinct morphologies. (author)

  17. Polyamide Microparticles Containing Vitamin C by Interfacial Polymerization: An Approach by Design of Experimentation

    Directory of Open Access Journals (Sweden)

    Lionel Ripoll

    2016-11-01

    Full Text Available Vitamin C is widely use in cosmetics and pharmaceutics products for its active properties. However ascorbic acid shows unfavourable chemical instability such as oxidation leading to formulation problems. Therefore, carriers, such as micro- and nanoparticles, have been widely investigated as delivery systems for vitamin C to improve its beneficial effects in skin treatment. However, none of the previous studies have been able to produce microparticles with a high encapsulation entrapment of vitamin C. The aim of the present study is to use an experimental design to optimize the synthesis of polyamide microparticles for the delivery of ascorbic acid. The effect of four formulation parameters on microparticles properties (size and morphology, encapsulation efficiency and yield, release kinetics were investigated using a surface response design. Finally, we were able to obtain stable microparticles containing more than 65% of vitamin C. This result confirms the effectiveness of using design of experiments for the optimisation of microparticle formulation and supports the proposal of using them as candidate for the delivery of vitamin C in skin treatment.

  18. Electron beam treatment with radical scavengers/enhancers

    International Nuclear Information System (INIS)

    Gehringer, P.

    1994-08-01

    E-beam treatment of low level contaminated groundwater is best apt to demonstrate the role of scavengers and enhancers, respectively because groundwater already contains some scavengers as natural solutes. The action of ionizing radiation to water is known to result in the formation of ions, molecular and free radical species. For low level contaminations of groundwater (pollutant concentration aqu - and H are of interest for pollutant decomposition. The pollutants have to compete for the free radical species with the natural solutes. 10 figures are discussed. (author)

  19. Free radical scavenging injectable hydrogels for regenerative therapy

    International Nuclear Information System (INIS)

    Komeri, Remya; Thankam, Finosh Gnanaprakasam; Muthu, Jayabalan

    2017-01-01

    Pathological free radicals generated from inflamed and infarcted cardiac tissues interferes natural tissue repair mechanisms. Hypoxic microenvironment at the injured zone of non-regenerating cardiac tissues hinders the therapeutic attempts including cell therapy. Here we report an injectable, cytocompatible, free radical scavenging synthetic hydrogel formulation for regenerative therapy. New hydrogel (PEAX-P) is prepared with D-xylitol-co-fumarate-co-poly ethylene adipate-co-PEG comaromer (PEAX) and PEGDiacrylate. PEAX-P hydrogel swells 4.9 times the initial weight and retains 100.07 kPa Young modulus at equilibrium swelling, which is suitable for cardiac applications. PEAX-P hydrogel retains elastic nature even at 60% compressive strain, which is favorable to fit with the dynamic and elastic natural tissue counterparts. PEAX-P hydrogel scavenges 51% DPPH radical, 40% hydroxyl radicals 41% nitrate radicals with 31% reducing power. The presence of hydrogel protects 62% cardiomyoblast cells treated with stress inducing media at LD 50 concentration. The free hydroxyl groups in sugar alcohols of the comacromer influence the free radical scavenging. Comparatively, PEAX-P hydrogel based on xylitol evinces slightly lower scavenging characteristics than with previously reported PEAM-P hydrogel containing mannitol having more hydroxyl groups. The possible free radical scavenging mechanism of the present hydrogel relies on the free π electrons associated with uncrosslinked fumarate bonds, hydrogen atoms associated with sugar alcohols/PEG and radical dilution by free water in the matrix. Briefly, the present PEAX-P hydrogel is a potential injectable system for combined antioxidant and regenerative therapy. - Graphical abstract: Injectable hydrogel with inherent free radical scavenging property for regenerative tissue engineering application. - Highlights: • Novel injectable hydrogel (PEAX-P) is prepared using D-xylitol-co-fumarate-co-poly ethylene adipate-co-PEG comaromer

  20. Free radical scavenging injectable hydrogels for regenerative therapy

    Energy Technology Data Exchange (ETDEWEB)

    Komeri, Remya [Sree Chitra Tirunal Institute for Medical Sciences and Technology, Polymer Science Division, BMT Wing, Thiruvananthapuram 695 012, Kerala State (India); Thankam, Finosh Gnanaprakasam [Dept. of Biomedical Sciences, Creighton University, 2500 California Plaza, Omaha NE68178 (United States); Muthu, Jayabalan, E-mail: mjayabalan52@gmail.com [Sree Chitra Tirunal Institute for Medical Sciences and Technology, Polymer Science Division, BMT Wing, Thiruvananthapuram 695 012, Kerala State (India)

    2017-02-01

    Pathological free radicals generated from inflamed and infarcted cardiac tissues interferes natural tissue repair mechanisms. Hypoxic microenvironment at the injured zone of non-regenerating cardiac tissues hinders the therapeutic attempts including cell therapy. Here we report an injectable, cytocompatible, free radical scavenging synthetic hydrogel formulation for regenerative therapy. New hydrogel (PEAX-P) is prepared with D-xylitol-co-fumarate-co-poly ethylene adipate-co-PEG comaromer (PEAX) and PEGDiacrylate. PEAX-P hydrogel swells 4.9 times the initial weight and retains 100.07 kPa Young modulus at equilibrium swelling, which is suitable for cardiac applications. PEAX-P hydrogel retains elastic nature even at 60% compressive strain, which is favorable to fit with the dynamic and elastic natural tissue counterparts. PEAX-P hydrogel scavenges 51% DPPH radical, 40% hydroxyl radicals 41% nitrate radicals with 31% reducing power. The presence of hydrogel protects 62% cardiomyoblast cells treated with stress inducing media at LD 50 concentration. The free hydroxyl groups in sugar alcohols of the comacromer influence the free radical scavenging. Comparatively, PEAX-P hydrogel based on xylitol evinces slightly lower scavenging characteristics than with previously reported PEAM-P hydrogel containing mannitol having more hydroxyl groups. The possible free radical scavenging mechanism of the present hydrogel relies on the free π electrons associated with uncrosslinked fumarate bonds, hydrogen atoms associated with sugar alcohols/PEG and radical dilution by free water in the matrix. Briefly, the present PEAX-P hydrogel is a potential injectable system for combined antioxidant and regenerative therapy. - Graphical abstract: Injectable hydrogel with inherent free radical scavenging property for regenerative tissue engineering application. - Highlights: • Novel injectable hydrogel (PEAX-P) is prepared using D-xylitol-co-fumarate-co-poly ethylene adipate-co-PEG comaromer

  1. Free radical-scavenging delta-lactones from Boletus calopus.

    Science.gov (United States)

    Kim, Jin-Woo; Yoo, Ick-Dong; Kim, Won-Gon

    2006-12-01

    The methanol extracts from the fruiting body of the mushroom Boletus calopus showed free radical-scavenging activity. Bioactivity-guided fractionation of the methanol extracts led to a new hydroxylated calopin named calopin B, along with the known delta-lactones calopin and cyclocalopin A. The structure of the new calopin analogue was elucidated by spectroscopic methods. All compounds showed potent free radical-scavenging activity against superoxide, DPPH, and ABTS radicals with IC (50) values of 1.2 - 5.4 microg/mL.

  2. Process for scavenging hydrogen sulfide from hydrocarbon gases

    International Nuclear Information System (INIS)

    Fox, I.

    1981-01-01

    A process for scavenging hydrogen sulfide from hydrocarbon gases utilizes iron oxide particles of unique chemical and physical properties. These particles have large surface area, and are comprised substantially of amorphous Fe 2 O 3 containing a crystalline phase of Fe 2 O 3 , Fe 3 O 4 and combinations thereof. In scavenging hydrogen sulfide, the iron oxide particles are suspended in a liquid which enters into intimate mixing contact with hydrocarbon gases; the hydrogen sulfide is reacted at an exceptional rate and only acid-stable reaction products are formed. Thereafter, the sweetened hydrocarbon gases are collected

  3. Performance of zeolite scavenge column in Xe monitoring system

    International Nuclear Information System (INIS)

    Wang Qian; Wang Hongxia; Li Wei; Bian Zhishang

    2010-01-01

    In order to improve the performance of zeolite scavenge column, its ability of removal of humidity and carbon dioxide was studied by both static and dynamic approaches. The experimental results show that various factors, including the column length and diameter, the mass of zeolite, the content of water in air, the temperature rise during adsorption, and the activation effectiveness all effect the performance of zeolite column in scavenging humanity and carbon dioxide. Based on these results and previous experience, an optimized design of the zeolite column is made for use in xenon monitoring system. (authors)

  4. Free radical scavenging activity of Eagle tea and their flavonoids

    Directory of Open Access Journals (Sweden)

    Qiong Meng

    2012-06-01

    Full Text Available In this study, an online HPLC-DAD-MS coupled with 2,2′-azinobis (3-ethylbenzthiazoline-6-sulfonic acid diammonium salt (ABTS assay was employed for evaluating free radical scavenging activity of Eagle tea and their active components. Twenty-three chromatographic peaks were detected, and nineteen components had free radical scavenging activity. Among them, eight compounds were identified as flavonoids (hyperin, isoquercitrin, quercitrin, quercetin, kaempferol, catechins, chlorogenic acid and epicatechin based on MS data and standard chromatographic characters.

  5. In vitro and in vivo biocompatibility and osteogenesis of graphene-reinforced nanohydroxyapatite polyamide66 ternary biocomposite as orthopedic implant material

    Directory of Open Access Journals (Sweden)

    Zhang S

    2016-07-01

    Full Text Available Shiyang Zhang,1 Qiming Yang,1 Weikang Zhao,1 Bo Qiao,1 Hongwang Cui,1 Jianjun Fan,2 Hong Li,3 Xiaolin Tu,4 Dianming Jiang1 1Department of Orthopedics, The First Affiliated Hospital of Chongqing Medical University, 2Molecular Medicine and Cancer Research Centre, Chongqing Medical University, Chongqing, 3College of Physical Science and Technology, Sichuan University, Chengdu, 4Institutes of Life Sciences, Chongqing Medical University, Chongqing, People’s Republic of China Abstract: Graphene and its derivatives have been receiving increasing attention regarding their application in bone tissue engineering because of their excellent characteristics, such as a vast specific surface area and excellent mechanical properties. In this study, graphene-reinforced nanohydroxyapatite/polyamide66 (nHA/PA66 bone screws were prepared. The results of scanning electron microscopy observation and X-ray diffraction data showed that both graphene and nHA had good dispersion in the PA66 matrix. In addition, the tensile strength and elastic modulus of the composites were significantly improved by 49.14% and 21.2%, respectively. The murine bone marrow mesenchymal stem cell line C3H10T1/2 exhibited better adhesion and proliferation in graphene reinforced nHA/PA66 composite material compared to the nHA/PA66 composites. The cells developed more pseudopods, with greater cell density and a more distinguishable cytoskeletal structure. These results were confirmed by fluorescent staining and cell viability assays. After C3H10T1/2 cells were cultured in osteogenic differentiation medium for 7 and 14 days, the bone differentiation-related gene expression, alkaline phosphatase, and osteocalcin were significantly increased in the cells cocultured with graphene reinforced nHA/PA66. This result demonstrated the bone-inducing characteristics of this composite material, a finding that was further supported by alizarin red staining results. In addition, graphene reinforced nHA/PA66

  6. Preparation of Novel Thin-Film Composite Nanofiltration Membranes for Separation of Amoxicillin

    Directory of Open Access Journals (Sweden)

    A. Akbari

    2014-04-01

    Full Text Available Several novel composite membranes were prepared to separate and recycle amoxicillin from pharmaceutical wastewater via nanofiltration process. The synthesis of these membranes included three stages: 1- preparation of polysulfone ultrafiltration membranes as a support via phase separation process, 2- modification of its surface by interfacial polymerization as a selective layer (polyamide, and 3- self-assembly of TiO2 nanoparticles on the selective layer as an anti-fouling agent. The rejection of all nanofiltration membranes was more than 99% and only its flux was changed proportional to different conditions. In the presence and absence of TiO2 nanoparticles, the pure water flux of polyamide thin-film membrane also obtained 44.4 and 38.4 L/h.m2 at 4 bar pressure, respectively. These were equal to 34 L/h.m2 for amoxicillin solutions. The results showed that TiO2 nanoparticles increased hydrophilicity of polyamide selective layer and therefore, nanoparticles decreased the fouling level. SEM images illustrated the excellent establishment of polyamide layer and distribution of TiO2 nanoparticles on the selective layer. The properties of membrane surface were taken into consideration by using AFM, indicating the increment of surface roughness with interfacial polymerization and TiO2 nanoparticles self-assembly. The pore size of membranes was in the nanoscale (2.653 and 2.604 nm without and with TiO2 nanoparticles self-assembly, respectively

  7. Influence of intense scavenging on Pa-Th fractionation in the wake of Kerguelen Island (Southern Ocean)

    International Nuclear Information System (INIS)

    Venchiarutti, C.; Roy-Barman, M.; Freydier, R.; Van Beek, P.; Souhaut, M.; Jeandel, C.

    2011-01-01

    Dissolved and particulate excess 230 Th and 231 Pa concentrations (noted 230 Th xs and 231 Pa xs respectively) and 231 Pa xs / 230 Th xs activity ratios were investigated on and out of the Kerguelen plateau (Southern Ocean) in the framework of the Kerguelen Ocean and Plateau compared Study project in order to better understand the influence of particle flux and particle chemistry and advection on the scavenging of 231 Pa. In the wake of Kerguelen, particulate 231 Pa xs is relatively abundant compared to its content in the dissolved phase. This, together with the low fractionation observed between 230 Th and 231 Pa (F Th/Pa ranging from 0.06 ± 0.01 to 1.6 ± 0.2) reflects the domination of the biogenic silica in the particle pool. Along the eastern escarpment of the Kerguelen plateau, the strong 231 Pa xs horizontal gradient in the deep waters highlights the intense removal of 231 Pa at depth, as already observed for 230 Th xs . This local boundary scavenging was attributed to re-suspension of opal-rich particles by nepheloid layers, resulting in fractionation factors F Th/Pa ≤ 1 along the Kerguelen plateau slope. Therefore, both the composition (biogenic opal) and the flux (intense along the margin) of particles control the scavenging of the two radionuclides in the Kerguelen wake. The modelling of 231 Pa distribution with an advection-scavenging model demonstrates that lateral advection of open ocean water on the Kerguelen plateau could supply most of the 231 Pa, which is then efficiently scavenged on the highly productive plateau, as previously proposed for 230 Th xs . It stresses that lateral advection can play a significant role in the overall budget of particle reactive trace elements in a coastal-open ocean system. (authors)

  8. Mechanical and rheological properties of nanocomposites of polyamide 6 with national organoclay; Propriedades mecanicas e reologicas de nanocompositos de poliamida 6 com argila organofilica nacional

    Energy Technology Data Exchange (ETDEWEB)

    Paz, Rene Anisio da; Leite, Amanda Melissa Damiao; Araujo, Edcleide Maria; Melo, Tomas Jeferson Alves de, E-mail: rene@cct.ufcg.edu.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais; Pessan, Luiz Antonio; Passador, Fabio Roberto [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil). Departamento de Engenharia de Materiais

    2013-07-01

    Nanocomposites of polyamide 6 with organoclay were prepared by melt intercalation and their rheological and mechanical properties were studied. The clay was treated with the quaternary ammonium salt (Cetremide) and characterized by Infrared Spectroscopy (FTIR) and X-ray diffraction (XRD). The results showed the incorporation of salt in the clay and its organophilization. A master was prepared with PA6/clay (1:1) by weight and this was added to the pure polyamide 6 to reach the nominal proportion of 3% of clay, using a co-rotational twin screw extruder. The samples were molded by injection and characterized by: capillary rheometry, XRD, TEM and mechanical testing (tensile and impact). The results of capillary rheometry showed that the presence of organoclay in the PA6 increased the viscosity of the systems. With XRD and TEM, it was verified that all systems presented predominantly exfoliated structure. The tensile properties of the nanocomposites were better than those of pure polyamide 6. (author)

  9. Comparative study by TG and DSC Of membranes polyamide66/bentonite clay nanocomposite; Estudo comparativo por TG e DSC de membranas de nanocompositos poliamida66/argila bentonitica

    Energy Technology Data Exchange (ETDEWEB)

    Medeiros, K.M. de; Kojuch, L R; Araujo, E M; Lira, H.L., E-mail: keilamm@ig.com.b [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais; Lima, F [Universidade Estadual da Paraiba (UEPB), Campina Grande, PB (Brazil). Dept. de Quimica

    2010-07-01

    In this study, it was obtained membranes of nanocomposites polyamide66 with 3 and 5% bentonite clay consists of silicates in layers from the interior of Paraiba. The clay was treated with a quaternary ammonium salt in order to make it organophilic. The membranes were prepared by phase inversion technique from the nanocomposites in solution. The clays were characterized by X-ray diffraction (XRD) and thermogravimetry (TG). Also the membranes were characterized by differential scanning calorimetry (DSC) and TG. The XRD and TG confirmed the presence of salt in the clay and thermal stability of the treated clay. For DSC, it was observed that there was no change in melting temperature of the membranes of nanocomposites compared to membrane pure polyamide66. By TG, it was found that the decomposition of the membranes of polyamide66 with treated clay were higher compared with the untreated clay. (author)

  10. Evaluation of Antioxidant and Free Radical Scavenging Abilities of ...

    African Journals Online (AJOL)

    Objective: This study was aimed at determining the antioxidants and free radical scavenging abilities of some packaged fruit juices (PFJ) widely used as source of fluids in Nigeria. Materials and methods: Packaged fruit juice samples produced by The Coca cola Company and Chi company namely: Apple(AP), blackcurrant, ...

  11. Scavenger and antioxidant properties of prenylflavones isolated from Artocarpus heterophyllus.

    Science.gov (United States)

    Ko, F N; Cheng, Z J; Lin, C N; Teng, C M

    1998-07-15

    The antioxidant properties of prenylflavones, isolated from Artocarpus heterophyllus Lam., was evaluated in this study. Among them, artocarpine, artocarpetin, artocarpetin A, and cycloheterophyllin diacetate and peracetate had no effect on iron-induced lipid peroxidation in rat brain homogenate. They also did not scavenge the stable free radical 1,1-diphenyl-2-picrylhydrazyl. In contrast, cycloheterophyllin and artonins A and B inhibited iron-induced lipid peroxidation in rat brain homogenate and scavenged 1,1-diphenyl-2-picrylhydrazyl. They also scavenged peroxyl radicals and hydroxyl radicals that were generated by 2,2'-azobis(2-amidinopropane) dihydrochloride and the Fe3+-ascorbate-EDTA-H2O2 system, respectively. However, they did not inhibit xanthine oxidase activity or scavenge superoxide anion, hydrogen peroxide, carbon radical, or peroxyl radicals derived from 2,2'-azobis(2,4-dimethylvaleronitrile) in hexane. Moreover, cycloheterophyllin and artonins A and B inhibited copper-catalyzed oxidation of human low-density lipoprotein, as measured by fluorescence intensity, thiobarbituric acid-reactive substance and conjugated-diene formations and electrophoretic mobility. It is concluded that cycloheterophyllin and artonins A and B serve as powerful antioxidants against lipid peroxidation when biomembranes are exposed to oxygen radicals.

  12. Energy scavenging strain absorber: application to kinetic dielectric elastomer generator

    Science.gov (United States)

    Jean-Mistral, C.; Beaune, M.; Vu-Cong, T.; Sylvestre, A.

    2014-03-01

    Dielectric elastomer generators (DEGs) are light, compliant, silent energy scavengers. They can easily be incorporated into clothing where they could scavenge energy from the human kinetic movements for biomedical applications. Nevertheless, scavengers based on dielectric elastomers are soft electrostatic generators requiring a high voltage source to polarize them and high external strain, which constitutes the two major disadvantages of these transducers. We propose here a complete structure made up of a strain absorber, a DEG and a simple electronic power circuit. This new structure looks like a patch, can be attached on human's wear and located on the chest, knee, elbow… Our original strain absorber, inspired from a sailing boat winch, is able to heighten the external available strain with a minimal factor of 2. The DEG is made of silicone Danfoss Polypower and it has a total area of 6cm per 2.5cm sustaining a maximal strain of 50% at 1Hz. A complete electromechanical analytical model was developed for the DEG associated to this strain absorber. With a poling voltage of 800V, a scavenged energy of 0.57mJ per cycle is achieved with our complete structure. The performance of the DEG can further be improved by enhancing the imposed strain, by designing a stack structure, by using a dielectric elastomer with high dielectric permittivity.

  13. Is the scavenger receptor MARCO a new immune checkpoint?

    Science.gov (United States)

    Arredouani, Mohamed S

    2014-11-01

    Whereas macrophages use the scavenger receptor MARCO primarily in antimicrobial immunity by interacting with both exogenous and endogenous environments, in dendritic cells (DCs) MARCO is believed to pleiotropically link innate to adaptive immunity. MARCO exerts a significant modulatory effect on TLR-induced DC activation, thus offering novel avenues in cancer immunotherapy.

  14. Scavenging rate ecoassay: a potential indicator of estuary condition.

    Science.gov (United States)

    Porter, Augustine G; Scanes, Peter R

    2015-01-01

    Monitoring of estuary condition is essential due to the highly productive and often intensely impacted nature of these ecosystems. Assessment of the physico-chemical condition of estuaries is expensive and difficult due to naturally fluctuating water quality and biota. Assessing the vigour of ecosystem processes is an alternative method with potential to overcome much of the variability associated with physico-chemical measures. Indicators of estuary condition should have small spatial and temporal variability, have a predictable response to perturbation and be ecologically relevant. Here, we present tests of the first criterion, the spatio-temporal variability of a potential ecoassay measuring the rate of scavenging in estuaries. We hypothesised that the proposed scavenging ecoassay would not vary significantly among A) sites in an estuary, B) trips separated by weeks, or C) days in a trip. Because not all habitats are present in all estuaries, this test was undertaken in two habitats. When conducted over bare substrate there were occasional significant differences, but no discernible patterns, within levels of the experiment. When conducted over vegetated substrate, days within a trip did not vary significantly, but later trips experienced greater scavenging. This scavenging ecoassay shows potential as a tool for assessing the condition of estuarine ecosystems, and further exploration of this protocol is warranted by implementation in estuaries across a gradient of anthropogenic stress.

  15. Free radical scavenging activity and phenolic contents of ...

    African Journals Online (AJOL)

    Anthocleista djalonensis extract is widely used in Nigerian folk medicine to treat conditions whose pathogenesis implicate oxidative stress, such as diabetes and hepatitis. However, little is known of the mechanism underlying these activities. In this study, the free radical scavenging potential of a methanol extract of A.

  16. 21 CFR 868.5430 - Gas-scavenging apparatus.

    Science.gov (United States)

    2010-04-01

    ...) Identification. A gas-scavenging apparatus is a device intended to collect excess anesthetic, analgesic, or trace gases or vapors from a patient's breathing system, ventilator, or extracorporeal pump-oxygenator, and to conduct these gases out of the area by means of an exhaust system. (b) Classification. Class II...

  17. Reward Your Students with an Online Scavenger Hunt!

    Science.gov (United States)

    Board, Keith

    2013-01-01

    Do you have a class of students who do excellent work and whom you would like to give an enjoyable reward? Try an "Internet scavenger hunt" for a fun and educational change of pace! This article shares how to run the activity.

  18. Scavenger receptor AI/II truncation, lung function and COPD

    DEFF Research Database (Denmark)

    Thomsen, M; Nordestgaard, B G; Tybjaerg-Hansen, A

    2011-01-01

    The scavenger receptor A-I/II (SRA-I/II) on alveolar macrophages is involved in recognition and clearance of modified lipids and inhaled particulates. A rare variant of the SRA-I/II gene, Arg293X, truncates the distal collagen-like domain, which is essential for ligand recognition. We tested whet...

  19. Contrasting Boundary Scavenging in two Eastern Boundary Current Regimes

    Science.gov (United States)

    Anderson, R. F.; Fleisher, M. Q.; Pavia, F. J.; Vivancos, S. M.; Lu, Y.; Zhang, P.; Cheng, H.; Edwards, R. L.

    2016-02-01

    We use data from two US GEOTRACES expeditions to compare boundary scavenging intensity in two eastern boundary current systems: the Canary Current off Mauritania and the Humboldt Current off Peru. Boundary scavenging refers to the enhanced removal of trace elements from the ocean by sorption to sinking particles in regions of greater than average particle abundance. Both regimes experience high rates of biological productivity and generation of biogenic particles, with rates of productivity potentially a little greater off Peru, whereas dust fluxes are an order of magnitude greater off NW Africa (see presentation by Vivancos et al., this meeting). Despite greater productivity off Peru, we find greater intensity of scavenging off NW Africa as measured by the residence time of dissolved 230Th integrated from the surface to a depth of 2500 m (10-11 years off NW Africa vs. 15-17 years off Peru). Dissolved 231Pa/230Th ratios off NW Africa (Hayes et al., Deep Sea Res.-II 116 (2015) 29-41) are nearly twice the values observed off Peru. We attribute this difference to the well-known tendency for lithogenic phases (dust) to strongly fractionate in favor of Th uptake during scavenging and removal, leaving the dissolved phase enriched in Pa. This behavior needs to be considered when interpreting sedimentary 231Pa/230Th ratios as a paleo proxy.

  20. Clustered DNA damage on subcellular level: effect of scavengers

    Czech Academy of Sciences Publication Activity Database

    Pachnerová Brabcová, Kateřina; Sihver, L.; Yasuda, N.; Matuo, Y.; Štěpán, Václav; Davídková, Marie

    2014-01-01

    Roč. 53, č. 4 (2014), s. 705-712 ISSN 0301-634X R&D Projects: GA MŠk LD12008 Institutional support: RVO:61389005 Keywords : clustered damage * indirect effects * haevy ion * plasmid in liquid water * scavenger Subject RIV: BO - Biophysics Impact factor: 1.528, year: 2014

  1. Hydroxyl radical scavenging activity of peptide from sea cucumber ...

    African Journals Online (AJOL)

    enzyme complex, sea cucumber protein hydrolysis was carried out to obtain hydrolysates that have hydroxyl-radical-scavenging activity (HRSA). The hydrolytic process was monitored by HRSA and conditions for this process were optimized as follows: pH 6.5, temperature 35°C, 12 mg enzyme complex in a reaction solution ...

  2. Free Radical Scavenging Activity of Scoparia dulcis Extract.

    Science.gov (United States)

    Babincová, M.; Sourivong, P.

    2001-01-01

    We studied the scavenging capabilities of an extract of Scoparia dulcis (a cosmopolitan weed widespread in Laos and Vietnam) for 1-diphenyl-2-picrylhydrazyl and measured hemoglobin-catalyzed linoleic acid peroxidation with an oxygen electrode. Our results demonstrated strong antioxidant activity corresponding to mitigation of the generation of hydroxyl radicals, a possible rationale for the observed therapeutic effects of this weed.

  3. Scavenger Receptor BI Plays a Role in Facilitating Chylomicron Metabolism

    NARCIS (Netherlands)

    Out, R.; Kruijt, J.K.; Rensen, P.C.N.; Hildebrand, R.B.; Vos, P. de; Eck, M. van; Berkel, T.J.C. van

    2004-01-01

    The function of scavenger receptor class B type I (SR-BI) in mediating the selective uptake of high density lipoprotein (HDL) cholesterol esters is well established. However, the potential role of SR-BI in chylomicron and chylomicron remnant metabolism is largely unknown. In the present

  4. Genetic Variant of the Scavenger Receptor BI in Humans

    NARCIS (Netherlands)

    Vergeer, Menno; Korporaal, Suzanne J. A.; Franssen, Remco; Meurs, Illiana; Out, Ruud; Hovingh, G. Kees; Hoekstra, Menno; Sierts, Jeroen A.; Dallinga-Thie, Geesje M.; Motazacker, Mohammad Mahdi; Holleboom, Adriaan G.; van Berkel, Theo J. C.; Kastelein, John J. P.; van Eck, Miranda; Kuivenhoven, Jan Albert

    2011-01-01

    BACKGROUND In mice, the scavenger receptor class B type I (SR-BI) is essential for the delivery of high-density lipoprotein (HDL) cholesterol to the liver and steroidogenic organs. Paradoxically, elevated HDL cholesterol levels are associated with increased atherosclerosis in SR-BI-knockout mice. It

  5. Genetic variant of the scavenger receptor BI in humans

    NARCIS (Netherlands)

    Vergeer, Menno; Korporaal, Suzanne J A; Franssen, Remco; Meurs, Illiana; Out, Ruud; Hovingh, G Kees; Hoekstra, Menno; Sierts, Jeroen A; Dallinga-Thie, Geesje M; Motazacker, Mohammad Mahdi; Holleboom, Adriaan G; Van Berkel, Theo J C; Kastelein, John J P; Van Eck, Miranda; Kuivenhoven, Jan Albert

    2011-01-01

    BACKGROUND: In mice, the scavenger receptor class B type I (SR-BI) is essential for the delivery of high-density lipoprotein (HDL) cholesterol to the liver and steroidogenic organs. Paradoxically, elevated HDL cholesterol levels are associated with increased atherosclerosis in SR-BI-knockout mice.

  6. Antioxidant and free radical scavenging activities of plant extracts ...

    African Journals Online (AJOL)

    Twenty-two species of medicinal plants collected in the Mexican state of Morelos were selected to evaluate their free radical scavenging and antioxidant activities. The extracts from the aerial parts of the plants were obtained using hexane, acetone and methanol (66 extracts). The initial qualitative screening of antioxidants ...

  7. Mitochondrial respiration scavenges extramitochondrial superoxide anion via a nonenzymatic mechanism.

    OpenAIRE

    Guidot, D M; Repine, J E; Kitlowski, A D; Flores, S C; Nelson, S K; Wright, R M; McCord, J M

    1995-01-01

    We determined that mitochondrial respiration reduced cytosolic oxidant stress in vivo and scavenged extramitochondrial superoxide anion (O2-.) in vitro. First, Saccharomyces cerevisiae deficient in both the cytosolic antioxidant cupro-zinc superoxide dismutase (Cu,Zn-SOD) and electron transport (Rho0 state) grew poorly (P 0.05) in all yeast. Seco...

  8. Free radical scavenging and cytotoxic activity of five commercial ...

    African Journals Online (AJOL)

    Polygonum cuspidatum), and pomegranate (Punica granatum). It shows radical scavenging activity in the following order, according to their median effective concentration (EC

  9. Using Scavenger Hunts to Familiarize Students with Scientific Journal Articles.

    Science.gov (United States)

    Lijek, Rebeccah S; Fankhauser, Sarah C

    2016-03-01

    Primary scientific literature can be difficult to navigate for anyone unfamiliar with its foreign, formal structure. We sought to create a fun, easy learning tool to help familiarize students of all ages with the structure of a scientific article. Our main learning objective was for the student to realize that science writing is formulaic-that specific information is found in predictable locations within an article-and that, with an understanding of the formula, anyone can comfortably navigate any journal article and accurately predict what to expect to find in each section. To this end, we designed a Journal Article Scavenger Hunt that requires the user to find and identify a series of commonplace features of a primary research article. The scavenger hunt activity is quick and easy to implement, and is adaptable to various ages and settings, including the classroom, lab, and at outreach events. The questions in the scavenger hunt can be scaled in difficulty and specificity to suit the instructor's needs. Over many years of using this activity, we have received positive feedback from students of all ages, from elementary school students to lay adult-learners as well as science teachers themselves. By making the unknown seem predictable and approachable, the scavenger hunt helps a variety of audiences feel more comfortable with science and more confident in their ability to engage directly with the scientific literature. Journal of Microbiology & Biology Education.

  10. Ambient RF energy scavenging: GSM and WLAN power density measurements

    NARCIS (Netherlands)

    Visser, H.J.; Reniers, A.C.F.; Theeuwes, J.A.C.

    2009-01-01

    To assess the feasibility of ambient RF energy scavenging, a survey of expected power density levels distant from GSM-900 and GSM-1800 base stations has been conducted and power density measurements have been performed in a WLAN environment. It appears that for distances ranging from 25 m to 100 m

  11. Forensically significant scavenging guilds in the southwest of Western Australia.

    Science.gov (United States)

    O'Brien, R Christopher; Forbes, Shari L; Meyer, Jan; Dadour, Ian

    2010-05-20

    Estimation of time since death is an important factor in forensic investigations and the state of decomposition of a body is a prime basis for such estimations. The rate of decomposition is, however, affected by many environmental factors such as temperature, rainfall, and solar radiation as well as by indoor or outdoor location, covering and the type of surface the body is resting upon. Scavenging has the potential for major impact upon the rate of decomposition of a body, but there is little direct research upon its effect. The information that is available relates almost exclusively to North American and European contexts. The Australian faunal assemblage is unique in that it includes no native large predators or large detrivorous avians. This research investigates the animals that scavenge carcasses in natural outdoor settings in southern Western Australia and the factors which can affect each scavenger's activity. The research was conducted at four locations around Perth, Western Australia with different environmental conditions. Pig carcasses, acting as models for the human body, were positioned in an outdoor environment with no protection from scavengers or other environmental conditions. Twenty-four hour continuous time-lapse video capture was used to observe the pattern of visits of all animals to the carcasses. The time of day, length of feeding, material fed upon, area of feeding, and any movement of the carcass were recorded for each feeding event. Some species were observed to scavenge almost continually throughout the day and night. Insectivores visited the carcasses mostly during bloat and putrefaction; omnivores fed during all stages of decomposition and scavenging by carnivores, rare at any time, was most likely to occur during the early stages of decomposition. Avian species, which were the most prolific visitors to the carcasses in all locations, like reptiles, fed only during daylight hours. Only mammals and amphibians, which were seldom seen

  12. Free radical scavenging injectable hydrogels for regenerative therapy.

    Science.gov (United States)

    Komeri, Remya; Thankam, Finosh Gnanaprakasam; Muthu, Jayabalan

    2017-02-01

    Pathological free radicals generated from inflamed and infarcted cardiac tissues interferes natural tissue repair mechanisms. Hypoxic microenvironment at the injured zone of non-regenerating cardiac tissues hinders the therapeutic attempts including cell therapy. Here we report an injectable, cytocompatible, free radical scavenging synthetic hydrogel formulation for regenerative therapy. New hydrogel (PEAX-P) is prepared with D-xylitol-co-fumarate-co-poly ethylene adipate-co-PEG comaromer (PEAX) and PEGDiacrylate. PEAX-P hydrogel swells 4.9 times the initial weight and retains 100.07kPa Young modulus at equilibrium swelling, which is suitable for cardiac applications. PEAX-P hydrogel retains elastic nature even at 60% compressive strain, which is favorable to fit with the dynamic and elastic natural tissue counterparts. PEAX-P hydrogel scavenges 51% DPPH radical, 40% hydroxyl radicals 41% nitrate radicals with 31% reducing power. The presence of hydrogel protects 62% cardiomyoblast cells treated with stress inducing media at LD 50 concentration. The free hydroxyl groups in sugar alcohols of the comacromer influence the free radical scavenging. Comparatively, PEAX-P hydrogel based on xylitol evinces slightly lower scavenging characteristics than with previously reported PEAM-P hydrogel containing mannitol having more hydroxyl groups. The possible free radical scavenging mechanism of the present hydrogel relies on the free π electrons associated with uncrosslinked fumarate bonds, hydrogen atoms associated with sugar alcohols/PEG and radical dilution by free water in the matrix. Briefly, the present PEAX-P hydrogel is a potential injectable system for combined antioxidant and regenerative therapy. Copyright © 2016 Elsevier B.V. All rights reserved.

  13. Bonding properties of acrylonitrile butadiene rubber with polyamide mediated by a functional layer of silane coupling agent

    International Nuclear Information System (INIS)

    Sang, J.; Aisawa, S.; Hirahara, H.; Mori, K.

    2017-01-01

    This study demonstrates that coating layers, expected to be formed as self-assembled monolayers, of silane coupling agents can act as adhesion layers as the hydrogenated acrylonitrile butadiene rubber (HNBR) and polyamide (PA6) plate interfaces. The resulting PA6/HNBR joints showed excellent adhesion properties with cohesive failure and the interfaces were jointed through chemical bonds, which were confirmed by swelling tests. The surfaces and bonding properties of rubber and PA6 were studied by means of peel tests, X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and nanoscale infrared microscopy and chemical imaging (AFM-IR). (authors)

  14. Isolation and Quantification of Polyamide Cyclic Oligomers in Kitchen Utensils and Their Migration into Various Food Simulants

    OpenAIRE

    Abe, Yutaka; Mutsuga, Motoh; Ohno, Hiroyuki; Kawamura, Yoko; Akiyama, Hiroshi

    2016-01-01

    Small amounts of cyclic monomers and oligomers are present in polyamide (PA)-based kitchen utensils. In this study, we isolated eight PA-based cyclic monomers and oligomers from kitchen utensils made from PA6 (a polymer of ε-caprolactam) and PA66 (a polymer of 1,6-diaminohexane and adipic acid). Their structures were identified using high-resolution mass spectrometry and 1H- and 13C-nuclear magnetic resonance spectroscopy, and their residual levels in PA-based kitchen utensils and degree of m...

  15. Experiments on different materials (polyamide, stainless & galvanized steel) influencing geothermal CaCO3 scaling formation: Polymorphs & elemental incorporation

    Science.gov (United States)

    Wedenig, Michael; Dietzel, Martin; Boch, Ronny; Hippler, Dorothee

    2016-04-01

    Thermal water is increasingly used for heat and electric power production providing base-load capable renewable and virtually unlimited geothermal energy. Compared to other energy sources geothermal facilities are less harmful to the environment, i.e. chemically and visually. In order to promote the economic viability of these systems compared to other traditional and renewable energy sources, production hindering processes such as corrosion and scaling of components arising from the typically high salinity thermal waters have to be considered as important economic factors. In this context, using proper materials being in contact with the thermal water is crucial and a playground for further improvements. Aim of the study presented, are basic experiments and observations of scaling and corrosive effects from hydrothermal water interacting with different materials and surfaces (stainless steel, polyamide, galvanized steel) and in particular the nucleation and growth effects of these materials regarding the precipitation of solid carbonate phases. The incorporation of Mg, Sr and Ba cations into the carbonate scalings are investigated as environmental proxy. For this purpose, hydrothermal carbonate precipitating experiments were initialized by mixing NaHCO3 and Ca-Mg-Sr-Ba-chloride solutions at temperatures ranging from 40 to 80 °C in glass reactors hosting artificial substrates of the above mentioned materials. The experiments show a strong dependence of the precipitation behaviour of calcium carbonate polymorphs on the particular material being present. Stainless steel and polyamide seem to restrict aragonite formation, whereas galvanized steel supports aragonite nucleation. Vaterite formation is promoted by polyamide surfaces. Importantly, vaterite is more soluble (less stable) compared to the other anhydrous calcium carbonate polymorphs, i.e. vaterite can be more easily re-dissolved. Thus, the use of polyamide components might reduce the amount and durability of

  16. Rheological and mechanical properties of polyamide 6 modified by electron-beam initiated mediation process

    International Nuclear Information System (INIS)

    Shin, Boo Young; Kim, Jae Hong

    2015-01-01

    Polyamide (PA6) has been modified by electron-beam initiated mediator process to improve drawbacks of PA6. Glycidyl methacrylate (GMA) was chosen as a reactive mediator for modification process of PA6. The mixture of the PA6 and GMA was prepared by using a twin-screw extruder, and then the mixture was exposed to electron-beam irradiation at various doses at room temperature. The modified PA6 were characterized by observing rheological and mechanical properties and compared virgin PA6. Thermal properties, water absorption, and gel fraction were also investigated. Tight gel was not found even when PA6 was irradiated at 200 kGy. Complex viscosity and storage modulus of PA6 were remarkably increased by electron-beam irradiation with medium of GMA. Maximum increase in complex viscosity was 75 times higher than virgin PA6 at 0.1 rad/s when it was irradiated at 200 kGy with the GMA. Mechanical properties were also improved without scarifying of processability. The reaction mechanisms for the mediation process with the reactive mediator of GMA were estimated to elucidate the cause of significantly enhanced rheological and mechanical properties without loss of thermoplasticity. - Highlights: • PA6 was modified by the electron-beam initiated mediation process. • Maximum increase in complex viscosity of modified PA6 was 75 times higher than virgin PA6 at 0.1 rad/s. • Mechanical properties were improved without scarifying of processability. • The GMA as a mediator played a key role in the electron-beam initiated mediation process

  17. Electrospinning and characterization of polyamide 66 nanofibers with different molecular weights

    Directory of Open Access Journals (Sweden)

    Lilia Muller Guerrini

    2009-06-01

    Full Text Available Polyamide 66 (PA66 nanofibers of different molecular weights were obtained by electrospinning of formic acid solutions. An ionic salt, NaCl, was also added to the solutions to increase the conductivity. PA66 concentrations between 15-17 wt.(%/v and electrical fields between 2.0 and 2.5 kV/cm were the best conditions to produce the smallest nanofibers; however, the addition of NaCl increased the fibers average diameters.The characterization of the fibers was done by scanning electron microscopy (SEM, differential scanning calorimetry (DSC, wide angle X rays diffraction (WAXD and Fourier Transformed Infrared (FTIR. As the molecular weight decreased, the nanofibers average diameters also decreased; however, critical number average and weight average molecular weights were necessary for electrospinning. As the amounts of carboxyl terminal groups (CTG increased, the nanofibers average diameters decreased; however, above CTG's critical values of 8.7 x 10-5 mol.g-1 no electrospinning was possible. The addition of ionic salt increased the electrical conductivity of the solutions and increased the nanofibers' average diameters. By DSC, residual solvent in all the electrospun mats was found; two melting endotherms, one between 248 and 258 °C and the other one between 258 and 267 °C, depending on the sample were also observed. These endotherms were attributed to the melting, re-crystallization and re-melting of the PA66 α-phase. The nanofibers had low % of crystallinity compared to a textile fiber. By WAXS and FTIR, confirmation of the presence of α-phase crystals, of small dimensions and highly imperfect and of a very small amount of β and γ-phases crystals in the nanofibers structure was obtained.

  18. Electromechanical properties of polyamide/lycra fabric treated with PEDOT:PSS

    Science.gov (United States)

    Tadesse, M. G.; Mengistie, D. A.; Loghin, C.; Chen, Y.; Wang, L.; Catalin, D.; Müller, C.; Nierstrasz, V.

    2017-10-01

    One of the challenges in smart textiles is to develop suitable multifunctional materials that can address simultaneously several characteristics such as durability, stretchability, lightweight, and conductivity. Conductive polymers which showed success in different technological fields like polymer solar cells and light emitting diodes are promising in many smart textile applications. In this work, we treated a common polyamide/lycra knitted fabric with PEDOT:PSS for stretchable e-textiles. PEDOT:PSS, with DMSO as a conductivity enhancer and different ratios of water-based polyurethane dispersions as a binder, was applied to the fabric with simple immersion and coating applications. The effect of different application methods and binder ratio on the surface resistance of the fabric was monitored with four point probe electrical surface resistance measurement systems. Samples prepared by immersion technique are more uniform and have higher conductivity than those prepared by a coating technique. SEM images showed that PEDOT:PSS is incorporated into the structure in the immersion method while in the coating it is majorly present on the surface of the fabric. The tensile measurement showed that the acidic PEDOT:PSS and polyurethane dispersion coating has no adverse effect on the tensile strength of the fabric. The coated samples can be stretched up to 700% while still reasonably conductive. The resistance increases only by a small amount when samples were stretched cyclically by stretching 100%. Generally, samples prepared by the immersion method maintained better conductivity while stretching than those by a coating method. The washing fastness of the samples was also assessed.

  19. Development of nanocomposites polyamide66/ bentonite clay membranes obtained by solution for water-oil separation

    International Nuclear Information System (INIS)

    Medeiros, Keila Machado de

    2010-01-01

    Microporous membranes were obtained from nanocomposites polyamide66 and regional bentonite clay, through the technique of immersion precipitation. The nanocomposites were obtained by solution with a pre-established reaction time. The clay was treated with quaternary ammonium salt (Cetremide®) in order to make it organophilic. Untreated and treated clay were characterized by X-ray fluorescence (XRF) spectroscopy, Fourier transform infrared (FTIR), X-ray diffraction (XRD) and thermogravimetry (TG), which confirmed the insertion of the Cetremide® salt in the layers of clay and their thermal stability. While the membranes were characterized by XRD, TG, differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and flow measurements. The results of XRD, TG and DSC confirmed the thermal stability and morphological structure with intercalated/partially exfoliated lamellae of clay in the polymer matrix. By SEM, it was revealed an asymmetric morphology consisting of a skin layer and a porous sublayer. The higher clay content in the membrane give the lower film thickness. This influencing directly the flow measurements of the membranes produced from the nanocomposites. In general, the initial flow with distilled water through the membranes decrease and stabilise after 60 min, this due to a compression or swelling occurred in the membranes. In tests of water-oil separation it was found that the relationship J/J0 tends to be greater when using emulsions with lower concentration. The water-oil separation tests at concentrations of 300 and 500 ppm for all membranes showed a significant reduction in oil concentration in the permeate, thus showing that these membranes have potential for this application. (author)

  20. Preparation and water desalination properties of POSS-polyamide nanocomposite reverse osmosis membranes

    KAUST Repository

    Duan, Jintang

    2015-01-01

    The application of nanotechnology to thin-film nanocomposites (TFN) is a new route to enhance membrane performance in water desalination. Here, the potential of polyhedral oligomeric silsesquioxane (POSS) as the nanofiller in polyamide (PA) reverse osmosis membranes was systematically investigated. Four POSS materials (P-8Phenyl, P-8NH3Cl, P-8NH2 and P-1NH2) were introduced into the selective layer by physical blending or chemical fixation during standard interfacial polymerization. Water flux and NaCl rejection were measured with 2000ppm NaCl solution under 15.5bar pressure, and SEM and TEM images of membrane selective layers were obtained. Membranes prepared without POSS showed water flux of 20.0±0.5L/m2·h and salt rejection of 98.0±0.2%. TFN membranes prepared with 0.4% (w/v) P-8Phenyl in the organic phase showed a 65% increase in water flux compared to the pristine PA membrane while maintaining high salt rejection. The selective layer of this membrane maintained the typical ridge-and-valley structure of aromatic PA. Results with P-8NH3Cl and P-8NH2 added to the organic phase were similar. TFN membranes prepared with monoamine P-1NH2 in the organic phase had poor water flux of 3.2L/m2·h, a smooth and more hydrophobic surface, and a much thicker (~400nm) selective layer. One of the four POSS compounds studied, P-8NH3Cl, is sufficiently soluble in water for incorporation into the selective layer via the aqueous phase. Membranes were prepared with P-8NH3Cl in the aqueous phase at varying reaction time, loading, and additive (triethylamine) concentration. With these parameters optimized, water flux increased to 35.4L/m2·h.

  1. Influence of Nanomaterial Compatibilization Strategies on Polyamide Nanocomposites Properties and Nanomaterial Release during the Use Phase.

    Science.gov (United States)

    Fernández-Rosas, Elisabet; Vilar, Gemma; Janer, Gemma; González-Gálvez, David; Puntes, Victor; Jamier, Vincent; Aubouy, Laurent; Vázquez-Campos, Socorro

    2016-03-01

    The incorporation of small amounts of nanofillers in polymeric matrices has enabled new applications in several industrial sectors. The nanofiller dispersion can be improved by modifying the nanomaterial (NM) surface or predispersing the NMs to enhance compatibility. This study evaluates the effect of these compatibilization strategies on migration/release of the nanofiller and transformation of polyamide-6 (PA6), a thermoplastic polymer widely used in industry during simulated outdoors use. Two nanocomposites (NCs) containing SiO2 nanoparticles (NPs) with different surface properties and two multiwalled carbon nanotube (MWCNT) NCs obtained by different addition methods were produced and characterized, before and after accelerated wet aging conditions. Octyl-modified SiO2 NPs, though initially more aggregated than uncoated SiO2 NPs, reduced PA6 hydrolysis and, consequently, NM release. Although no clear differences in dispersion were observed between the two types of MWCNT NCs (masterbatch vs direct addition) after manufacture, the use of the MWCNT masterbatch reduced PA6 degradation during aging, preventing MWCNT accumulation on the surface and further release or potential exposure by direct contact. The amounts of NM released were lower for MWCNTs (36 and 108 mg/m(2)) than for SiO2 NPs (167 and 730 mg/m(2)), being lower in those samples where the NC was designed to improve the nanofiller-matrix interaction. Hence, this study shows that optimal compatibilization between NM and matrix can improve NC performance, reducing polymer degradation and exposure and/or release of the nanofiller.

  2. Adsorption of pharmaceuticals onto isolated polyamide active layer of NF/RO membranes.

    Science.gov (United States)

    Liu, Yan-Ling; Wang, Xiao-Mao; Yang, Hong-Wei; Xie, Yuefeng F

    2018-06-01

    Adsorption of trace organic compounds (TrOCs) onto the membrane materials has a great impact on their rejection by nanofiltration (NF) and reverse osmosis (RO) membranes. This study aimed to investigate the difference in adsorption of various pharmaceuticals (PhACs) onto different NF/RO membranes and to demonstrate the necessity of isolating the polyamide (PA) active layer from the polysulfone (PS) support layer for adsorption characterization and quantification. Both the isolated PA layers and the PA+PS layers of NF90 and ESPA1 membranes were used to conduct static adsorption tests. Results showed that apparent differences existed between the PA layer and the PA+PS layer in the adsorption capacity of PhACs as well as the time necessary to reach the adsorption equilibrium. PhACs with different physicochemical properties could be adsorbed to different extents by the isolated PA layer, which was mainly attributed to electrostatic attraction/repulsion and hydrophobic interactions. The PA layer of ESPA1 exhibited apparently higher adsorption capacities for the positively charged PhACs and similar adsorption capacities for the neutral PhACs although it had significantly less total interfacial area (per unit membrane surface area) for adsorption compared to the PA layer of NF90. The higher affinity of the PA layer of ESPA1 for the PhACs could be due to its higher capacity of forming hydrogen bonds with PhACs resulted from the modified chemistry with more -OH groups. This study provides a novel approach to determining the TrOC adsorption onto the active layer of membranes for the ease of investigating adsorption mechanisms. Copyright © 2018 Elsevier Ltd. All rights reserved.

  3. Influence of non-covalent modification of multiwalled carbon nanotubes on the crystallization behaviour of binary blends of polypropylene and polyamide 6.

    Science.gov (United States)

    Mukhopadhyay, Nabaneeta; Panwar, Ajay S; Kumar, Gulshan; Samajdar, I; Bhattacharyya, Arup R

    2015-02-14

    Blends of polypropylene (PP) and polyamide 6 (PA6) with multiwalled carbon nanotubes (MWNTs) were prepared using different processing strategies in a twin-screw micro-compounder. The effect of MWNTs on the crystallization behaviour of the PP phase and the PA6 phase of the blend has been investigated through non-isothermal crystallization studies by differential scanning calorimetric analysis. Furthermore, the effect of the addition of the compatibilizer (PP-g-MA) and the modification of MWNTs (m-MWNTs) with a non-covalent organic modifier (Li-salt of 6 amino hexanoic acid, Li-AHA) has also been studied in context to the crystallization behaviour of the PP and PA6 phase in the blend. The crystallization studies have indicated a significant increase in bulk crystallization temperature of the PP phase in the blend in the presence of MWNTs. Moreover, the formation of 'trans-lamellar crystalline' structure consisting of PA6 'trans-crystalline lamellae' on MWNTs surface was facilitated in the case of blends prepared via 'protocol 2' as compared to the corresponding blends prepared via 'protocol 1'. Wide angle X-ray diffraction analysis has showed the existence of a β-polymorph of the PP phase due to incorporation of the PA6 phase in the blend. Addition of MWNTs in the blends has facilitated further β-crystalline structure formation of the PP phase. In the presence of m-MWNTs, a higher β-fraction was observed in the PP phase as compared to the blend with pristine MWNTs. Addition of PP-g-MA has suppressed the β-phase formation in the PP phase in the blend. X-ray bulk texture analysis revealed that incorporation of PA6 as well as pristine/modified MWNTs has influenced the extent of orientation of the PP chains towards specific crystalline planes in various blend compositions of PP and PA6.

  4. Cooked blueberries: anthocyanin and anthocyanidin degradation and their radical-scavenging activity.

    Science.gov (United States)

    Oliveira, Carla; Amaro, L Filipe; Pinho, Olivia; Ferreira, Isabel M P L V O

    2010-08-25

    This study examined anthocyanin and anthocyanidin composition and radical-scavenging activity of three cultivars of blueberries (Vaccinium corymbosum L., cv. Bluecrop, Bluetravel, and Ozarkblue) before and after cooking. A total of 13 anthocyanins were separated and monitored in methanolic extracts of raw fruits by high-performance liquid chromatography/diode array detector (HPLC/DAD). Principal component analysis using the anthocyanin profile as variables revealed differences according to cultivar origin. Of the six common anthocyanidins, four were identified and quantified in the hydrolysates, namely, malvidin, the most abundant, followed by cyanidin, petunidin, and delphynidin. A systematic evaluation of the degradation of anthocyanins and anthocyanidins of blueberries cooked in stuffed fish was performed. The percentage of anthocyanin degradation in cooked blueberries (by progressive heating from 12 to 99 °C for 60 min) ranged between 16 and 30% for Bluecrop, 30-42% for Bluetravel, and 12-41% for Ozarkblue. However, cooked blueberries maintained or increased radical-scavenging activity when evaluated by the 1,1'-diphenyl-2-picrylhydrazyl (DPPH) method. Overall, results show that cooked blueberries can serve as a good source of bioactive phytochemicals.

  5. Cloud Scavenging Effects on Aerosol Radiative and Cloud-nucleating Properties - Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Ogren, John A.; Sheridan, Patrick S.; Andrews, Elisabeth

    2009-03-05

    The optical properties of aerosol particles are the controlling factors in determining direct aerosol radiative forcing. These optical properties depend on the chemical composition and size distribution of the aerosol particles, which can change due to various processes during the particles’ lifetime in the atmosphere. Over the course of this project we have studied how cloud processing of atmospheric aerosol changes the aerosol optical properties. A counterflow virtual impactor was used to separate cloud drops from interstitial aerosol and parallel aerosol systems were used to measure the optical properties of the interstitial and cloud-scavenged aerosol. Specifically, aerosol light scattering, back-scattering and absorption were measured and used to derive radiatively significant parameters such as aerosol single scattering albedo and backscatter fraction for cloud-scavenged and interstitial aerosol. This data allows us to demonstrate that the radiative properties of cloud-processed aerosol can be quite different than pre-cloud aerosol. These differences can be used to improve the parameterization of aerosol forcing in climate models.

  6. Researches on increasing compatibility between mixtures of PPS (poly-phenylene sulfide) and polyamide; Recherches en vue de la compatibilisation de melanges de polyamide et de polysulfure de phenylene

    Energy Technology Data Exchange (ETDEWEB)

    Montagne, O.

    1997-01-08

    This work aims to increase the compatibility between PPS (Poly Phenylene Sulfide) and a Polyamide. In order to do so, a bloc co-polymer was synthesised by the coupling of telechelic oligomers of PPS and PA oligomers. These telechelic oligomers of PPS were synthesised in a single step which a synthesis was made possible were the nitrile and secondary amide functions. These oligomers were characterised by various techniques which lead to a rather good precision (difficult to achieve for insolubility reasons). These oligomers were then coupled with the polyamide oligomers. In order to do so, a new reaction was discovered between an aromatic nitrile and a secondary aliphatic amide. It was assessed both on model molecules and on oligomers. An original mechanism is proposed. Once the characterisation of these copolymers was made, various blends of PPS and PA were studied. At last, the incorporation of the block copolymers in the blend obtained by a twin screw extruder, lead to an improvement of the compatibility between the two polymers and in an increase of the resistance to crack propagation. (author) 314 refs.

  7. Analysis of damage processes in short glass fibre reinforced polyamide under mechanical loading by X-ray refractometry, fracture mechanics and fractography; Analyse der Schaedigungsprozesse in einem kurzglasfaserverstaerkten Polyamid unter mechanischer Belastung mittels Roentgenrefraktometrie, Bruchmechanik und Fraktografie

    Energy Technology Data Exchange (ETDEWEB)

    Guenzel, Stephan

    2013-04-01

    This thesis presents an analysis of the damage behaviour in a short glass fibre reinforced polyamide. The micro cracking is investigated by X-ray refraction technique under various, mechanical in-service loadings. In this context, potentials and limits of X-ray refraction analysis for short glass fibre reinforced polyamides are compiled. In particular the influence of fibre orientation and the influence of damage mechanisms are examined according to the X-ray refraction analysis and its interpretation. The method offers a quantitative and phenomenological based characterisation of micro crack damage. For the investigated material micro crack damage emerges as fibre matrix debonding and matrix micro cracking. The state of damage correlates with a nonlinear strain portion in a linear manner and depends on the kind of loading. Absorption of moisture in the material may influence significantly the micro crack damage behaviour. Damage of micro cracking appears preferentially under tension. The macro damage due to propagation of a single crack is characterised in an automated test setup, considering the fibre orientation and content of moisture. Based on the findings an empirical assessment approach is developed. The investigations of the micro and macro damage behaviour are accompanied by fractography, in order to support the model assumptions according to damage and fracture mechanisms.

  8. Free radical scavenging potential, reducing power, phenolic and biochemical constituents of Porphyra species from India

    Digital Repository Service at National Institute of Oceanography (India)

    Pise, N.M.; Jena, K.B.; Maharana, D.; Gaikwad, D.; Jagtap, T.G.

    . Antioxidant potentials of algae were assessed through phenolic content, 2, 2-diphenyl-1- picrylhydrazyl (DPPH) activity, hydrogen peroxide (H sub(2)O sub(2)), scavenging power and reducing potential. A dose-dependent free radical scavenging action against DPPH...

  9. Precipitation scavenging of aerosol particles at a rural site in the Czech Republic

    Science.gov (United States)

    Zikova, Nadezda; Zdimal, Vladimir

    2017-04-01

    Wet deposition is an important removal mechanism of atmospheric aerosol (AA) in the troposphere, transferring AA to the Earth surface in an aqueous form (Seinfeld and Pandis, 1998). Deposition consists of in-cloud (ICS) and below-cloud (BCS) scavenging, both processes depending on the size, chemical composition and concentration of the AA particles (e.g. Laakso et al., 2003; Ladino et al., 2011). Due to the complexity of the processes and high instrumentation and time demands, a complete understanding is still a challenge, although both phenomena have been extensively studied recently (e.g. Andronache et al. 2006; Chate et al. 2011; Collett et al. 2008). In this work, the influence of ICS and BCS, described by the obscurities (mist, fog and shallow fog) and precipitation (drizzle, rain, snow, rain with snow), on submicron atmospheric aerosol particle number size distributions (PNSD) was studied using 5 years of measurements at the rural background station Košetice. The typical PNSD during individual meteorological phenomena were compared, and the change in the concentrations before and after the beginning of the phenomenon, the scavenging coefficient lambda_s, and the rate of change of the AA concentrations with time were computed. It was found that both obscurities and precipitation have a strong influence on the AA concentrations, both on the total number concentrations and on the particle number size distributions. The scavenging not only lowers the total AA concentrations, it even changes the number of modes on the PNSDs. The PNSD main mode is shifted to the larger particles, and the concentrations of particles smaller than 50 nm in diameter are considerably lower. In nucleation mode, however, wet scavenging does not seem to be the main process influencing the AA concentrations, although its considerable effect on the concentration was proved. During obscurities, there is a typical PNSD to which the PNSD converge at any mist/fog/shallow fog event. The

  10. Microbiological destruction of composite polymeric materials in soils

    Science.gov (United States)

    Legonkova, O. A.; Selitskaya, O. V.

    2009-01-01

    Representatives of the same species of microscopic fungi developed on composite materials with similar polymeric matrices independently from the type of soils, in which the incubation was performed. Trichoderma harzianum, Penicillium auranthiogriseum, and Clonostachys solani were isolated from the samples of polyurethane. Fusarium solani, Clonostachys rosea, and Trichoderma harzianum predominated on the surface of ultrathene samples. Ulocladium botrytis, Penicillium auranthiogriseum, and Fusarium solani predominated in the variants with polyamide. Trichoderma harzianum, Penicillium chrysogenum, Aspergillus ochraceus, and Acremonium strictum were isolated from Lentex-based composite materials. Mucor circinelloides, Trichoderma harzianum, and Penicillium auranthiogriseum were isolated from composite materials based on polyvinyl alcohol. Electron microscopy demonstrated changes in the structure of polymer surface (loosening and an increase in porosity) under the impact of fungi. The physicochemical properties of polymers, including their strength, also changed. The following substances were identified as primary products of the destruction of composite materials: stearic acid for polyurethane-based materials; imide of dithiocarbonic acid and 1-nonadecen in variants with ultrathene; and tetraaminopyrimidine and isocyanatodecan in variants with polyamide. N,N-dimethyldodecan amide, 2-methyloximundecanon and 2-nonacosane were identified for composites on the base of Lentex A4-1. Allyl methyl sulfide and imide of dithiocarbonic acid were found in variants with the samples of composites based on polyvinyl alcohol. The identified primary products of the destruction of composite materials belong to nontoxic compounds.

  11. Highly functionalized piperidines: Free radical scavenging, anticancer activity, DNA interaction and correlation with biological activity

    OpenAIRE

    Suvankar Das; Cristiane J. da Silva; Marina de M. Silva; Maria Dayanne de A. Dantas; Ângelo de Fátima; Ana Lúcia T. Góis Ruiz; Cleiton M. da Silva; João Ernesto de Carvalho; Josué C.C. Santos; Isis M. Figueiredo; Edeildo F. da Silva-Júnior; Thiago M. de Aquino; João X. de Araújo-Júnior; Goutam Brahmachari; Luzia Valentina Modolo

    2018-01-01

    Twenty-five piperidines were studied as potential radical scavengers and antitumor agents. Quantitative interaction of compounds with ctDNA using spectroscopic techniques was also evaluated. Our results demonstrate that the evaluated piperidines possesses different abilities to scavenge the radical 2,2-diphenyl-1-picrylhydrazyl (DPPH) and the anion radical superoxide (·O2−). The piperidine 19 was the most potent radical DPPH scavenger, while the most effective to ·O2− scavenger was piperidine...

  12. Preparative separation of polyphenols from artichoke by polyamide column chromatography and high-speed counter-current chromatography

    International Nuclear Information System (INIS)

    Shu, Xikai; Wang, Mei; Liu, Daicheng; Wang, Daijie; Lin, Xiaojing; Liu, Jianhua; Wang, Xiao; Huang, Luqi

    2013-01-01

    An efficient method for the rapid separation and purification of polyphenols from artichoke by polyamide column chromatography in combination with high-speed counter-current chromatography (HSCCC) was successfully built. The crude ethanol extracts from dry artichoke were first pre-separated by polyamide column chromatography and divided in two parts as sample 1 and sample 2. Then, the samples were further separated by HSCCC and yielded 7.8 mg of chlorogenic acid (compound I), 24.5 mg of luteolin-7-O-β-D-rutinoside (compound II), 18.4 mg of luteolin-7-O-β-D-glucoside (compound III), and 33.4 mg of cynarin (compound IV) with purity levels of 92.0%, 98.2%, 98.5%, and 98.0%, respectively, as determined by high-performance liquid chromatography (HPLC) method. The chemical structures of these compounds were identified by electrospray ionization-mass spectrometry (ESI-MS) and nuclear magnetic resonance (NMR). (author)

  13. Sequence-specific DNA alkylation targeting for Kras codon 13 mutation by pyrrole-imidazole polyamide seco-CBI conjugates.

    Science.gov (United States)

    Taylor, Rhys Dylan; Asamitsu, Sefan; Takenaka, Tomohiro; Yamamoto, Makoto; Hashiya, Kaori; Kawamoto, Yusuke; Bando, Toshikazu; Nagase, Hiroki; Sugiyama, Hiroshi

    2014-01-27

    Hairpin N-methylpyrrole-N-methylimidazole polyamide seco-CBI conjugates 2-6 were designed for synthesis by Fmoc solid-phase synthesis, and their DNA-alkylating activities against the Kras codon 13 mutation were compared by high-resolution denaturing gel electrophoresis with 225 base pair (bp) DNA fragments. Conjugate 5 had high reactivity towards the Kras codon 13 mutation site, with alkylation occurring at the A of the sequence 5'-ACGTCACCA-3' (site 2), including minor 1 bp-mismatch alkylation against wild type 5'-ACGCCACCA-3' (site 3). Conjugate 6, which differs from conjugate 5 by exchanging one Py unit with a β unit, showed high selectivity but only weakly alkylated the A of 5'-ACGTCACCA-3' (site 2). The hairpin polyamide seco-CBI conjugate 5 thus alkylates according to Dervan's pairing rule with the pairing recognition which β/β pair targets T-A and A-T pairs. SPR and a computer-minimized model suggest that 5 binds to the target sequence with high affinity in a hairpin conformation, allowing for efficient DNA alkylation. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Preparative separation of polyphenols from artichoke by polyamide column chromatography and high-speed counter-current chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Shu, Xikai; Wang, Mei; Liu, Daicheng [College of Life Science, Shandong Normal University, Jinan, Shandong (China); Wang, Daijie; Lin, Xiaojing; Liu, Jianhua; Wang, Xiao; Huang, Luqi, E-mail: wxjn1998@126.com [Shandong Analysis and Test Center, Shandong Academy of Sciences, Jinan, Shandong (China)

    2013-09-01

    An efficient method for the rapid separation and purification of polyphenols from artichoke by polyamide column chromatography in combination with high-speed counter-current chromatography (HSCCC) was successfully built. The crude ethanol extracts from dry artichoke were first pre-separated by polyamide column chromatography and divided in two parts as sample 1 and sample 2. Then, the samples were further separated by HSCCC and yielded 7.8 mg of chlorogenic acid (compound I), 24.5 mg of luteolin-7-O-{beta}-D-rutinoside (compound II), 18.4 mg of luteolin-7-O-{beta}-D-glucoside (compound III), and 33.4 mg of cynarin (compound IV) with purity levels of 92.0%, 98.2%, 98.5%, and 98.0%, respectively, as determined by high-performance liquid chromatography (HPLC) method. The chemical structures of these compounds were identified by electrospray ionization-mass spectrometry (ESI-MS) and nuclear magnetic resonance (NMR). (author)

  15. Characterization of Polyamide 66 membranes prepared by phase inversion using formic acid and hydrochloric acid such as solvents

    Directory of Open Access Journals (Sweden)

    Patrícia Poletto

    2011-12-01

    Full Text Available The membranes properties prepared from water/formic acid (FA/ polyamide 66 (PA66 and water/hydrochloric acid (HCl/polyamide 66 (PA 66 systems has been studied. The different solvents interact distinctly with the polymer, affecting the membrane morphology. The asymmetric structure of the membranes showed a dense top layer and a porous sublayer. The membranes M-HCl prepared from HCl/PA 66 system showed a larger dense layer (around 23 μm in compared to those prepared from FA/PA 66 system (M-FA (around 10 μm. The membrane morphology was a determinant factor in results of water absorption, porosity and pure water flux. The lower thickness of dense layer in M-FA membranes resulted in a higher water absorption and, consequently, porosity, approximately 50%, compared with M-HCl membranes, approximately 15%. The same trend was observed to permeate flux, the lower thickness of dense layer higher pure water flux.

  16. Evaluation of Ultimate Pressure Capacity of a Prestressed Concrete Containment Building with Steel or Polyamide Fiber Reinforcement

    Energy Technology Data Exchange (ETDEWEB)

    Choun, Youngsun; Hahm, Daegi [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    Fiber reinforced concrete (FRC) includes thousands of small fibers that are distributed randomly in the concrete. Fibers resist the growth of cracks in concrete through their bridging at the cracks. Therefore, FRC fails in tension only when the fibers break or are pulled out of the cement matrix. For this reason, the addition of fibers in concrete mixing increases the tensile toughness of concrete and enhances the post-cracking behavior. A prevention of through-wall cracks and an increase of the post-cracking ductility will improve the ultimate internal pressure capacity of a prestressed concrete containment building (PCCB). In this study, the effects of steel or polyamide fiber reinforcement on the ultimate pressure capacity of a PCCB are evaluated. When R-SFRC contains hooked steel fibers in a volume fraction of 1.0%, the ultimate pressure capacity of a PCCB can be improved by 17%. When R-PFRC contains polyamide fibers in a volume fraction of 1.5%, the ultimate pressure capacity of a PCCB can be enhanced by 10%. Further studies are needed to determine the strain limits acceptable for PCCBs reinforced with fibers.

  17. Evaluation of Ultimate Pressure Capacity of a Prestressed Concrete Containment Building with Steel or Polyamide Fiber Reinforcement

    International Nuclear Information System (INIS)

    Choun, Youngsun; Hahm, Daegi

    2014-01-01

    Fiber reinforced concrete (FRC) includes thousands of small fibers that are distributed randomly in the concrete. Fibers resist the growth of cracks in concrete through their bridging at the cracks. Therefore, FRC fails in tension only when the fibers break or are pulled out of the cement matrix. For this reason, the addition of fibers in concrete mixing increases the tensile toughness of concrete and enhances the post-cracking behavior. A prevention of through-wall cracks and an increase of the post-cracking ductility will improve the ultimate internal pressure capacity of a prestressed concrete containment building (PCCB). In this study, the effects of steel or polyamide fiber reinforcement on the ultimate pressure capacity of a PCCB are evaluated. When R-SFRC contains hooked steel fibers in a volume fraction of 1.0%, the ultimate pressure capacity of a PCCB can be improved by 17%. When R-PFRC contains polyamide fibers in a volume fraction of 1.5%, the ultimate pressure capacity of a PCCB can be enhanced by 10%. Further studies are needed to determine the strain limits acceptable for PCCBs reinforced with fibers

  18. Superoxide scavenging activity of pirfenidone-iron complex

    International Nuclear Information System (INIS)

    Mitani, Yoshihiro; Sato, Keizo; Muramoto, Yosuke; Karakawa, Tomohiro; Kitamado, Masataka; Iwanaga, Tatsuya; Nabeshima, Tetsuji; Maruyama, Kumiko; Nakagawa, Kazuko; Ishida, Kazuhiko; Sasamoto, Kazumi

    2008-01-01

    Pirfenidone (PFD) is focused on a new anti-fibrotic drug, which can minimize lung fibrosis etc. We evaluated the superoxide (O 2 ·- ) scavenging activities of PFD and the PFD-iron complex by electron spin resonance (ESR) spectroscopy, luminol-dependent chemiluminescence assay, and cytochrome c reduction assay. Firstly, we confirmed that the PFD-iron complex was formed by mixing iron chloride with threefold molar PFD, and the complex was stable in distillated water and ethanol. Secondary, the PFD-iron complex reduced the amount of O 2 ·- produced by xanthine oxidase/hypoxanthine without inhibiting the enzyme activity. Thirdly, it also reduced the amount of O 2 ·- released from phorbor ester-stimulated human neutrophils. PFD alone showed few such effects. These results suggest the possibility that the O 2 ·- scavenging effect of the PFD-iron complex contributes to the anti-fibrotic action of PFD used for treating idiopathic pulmonary fibrosis

  19. The significance of cooking for early hominin scavenging.

    Science.gov (United States)

    Smith, Alex R; Carmody, Rachel N; Dutton, Rachel J; Wrangham, Richard W

    2015-07-01

    Meat scavenged by early Homo could have contributed importantly to a higher-quality diet. However, it has been suggested that because carrion would normally have been contaminated by bacteria it would have been dangerous and therefore eaten rarely prior to the advent of cooking. In this study, we quantified bacterial loads on two tissues apparently eaten by hominins, meat and bone marrow. We tested the following three hypotheses: (1) the bacterial loads on exposed surfaces of raw meat increase within 24 h to potentially dangerous levels, (2) simple roasting of meat on hot coals kills most bacteria, and (3) fewer bacteria grow on marrow than on meat, making marrow a relatively safe food. Our results supported all three hypotheses. Our experimental data imply that early hominins would have found it difficult to scavenge safely without focusing on marrow, employing strategies of carrion selection to minimize pathogen load, or cooking. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Radical scavenging compounds from the aerial parts of ...

    African Journals Online (AJOL)

    Results: The ethyl acetate and n-butanol fractions were the most active fractions and contained apigenin, apigenin glucuronide, luteolin, caffeic acid, methyl caffeate, rosmarinic acid and methyl rosmarinate as the radical scavenging compounds with EC50 values of 26.67 ± 0.31, 185.89 ± 1.02, 5.35 ± 0.31, 3.92 ± 0.06, ...

  1. In vitro free radical scavenging activity of platinum nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, Aki; Kajita, Masashi; Kim, Juewon; Kanayama, Atsuhiro; Miyamoto, Yusei [Department of Integrated Biosciences, Graduate School of Frontier Sciences, University of Tokyo, Bioscience Building 402, 5-1-5 Kashiwanoha, Kashiwa, Chiba 277-8562 (Japan); Takahashi, Kyoko; Mashino, Tadahiko, E-mail: yusei74@k.u-tokyo.ac.j [Department of Pharmaceutical Sciences, Faculty of Pharmacy, Keio University, 1-5-30 Shibakoen, Minato, Tokyo 105-8512 (Japan)

    2009-11-11

    A polyacrylic acid (PAA)-protected platinum nanoparticle species (PAA-Pt) was prepared by alcohol reduction of hexachloroplatinate. The PAA-Pt nanoparticles were well dispersed and homogeneous in size with an average diameter of 2.0 {+-} 0.4 nm (n = 200). We used electron spin resonance to quantify the residual peroxyl radical AOO. generated from 2,2-azobis (2-aminopropane) dihydrochloride (AAPH) by thermal decomposition in the presence of O{sub 2} and a spectrophotometric method to quantify the residual 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical. PAA-Pt scavenged these two radicals in a dose-dependent manner. Platinum was the functional component. PAA-Pt reduced the rate of oxygen consumption required for linoleic acid peroxidation initiated by AOO. generated from AAPH, indicating inhibition of the propagation of linolate peroxidation. A thiobarbituric acid test also revealed dose-dependent inhibition of the linolate peroxidation by PAA-Pt. Fifty micromolar platinum, as PAA-Pt, completely quenched 250 {mu}M DPPH radical for 5 min. Even when twice diluted in half, the PAA-Pt still quenched 100% of the 250 {mu}M DPPH radical. The scavenging activity of PAA-Pt is durable. These observations suggest that PAA-Pt is an efficient scavenger of free radicals.

  2. Scavenging of radionuclides in the marine environment, (1)

    International Nuclear Information System (INIS)

    Mahara, Yasunori

    1989-01-01

    It is very important to predict diffusion, scavenging and accumulation of the long lives radionuclides which may be discharged from the reprocessing plant in the marine environment, for the purpose of polishing up methods of the radiation does estimation to the high quality stage. This study reports that distribution and behavior of transuranic elements, which are extremely harmful for the human beings and are discharged probably from the reprocessing plant, are investigated in both the survey of bibliography and the in-situ observation. Results of the field observation on the distribution of transuranic elements in the marine show that plutonium and americium are easily scavenged from the sea water and are accumulated on the sea bottom. Transuranic elements, which are originated from fallout and are discharged from the reprocessing plant, have generally the similar distribution in the marine and the same chemical behavior. This facts suggest that the fallout data which are probably and easily collected in the world are available for fabrication of the scavenging model for transuranic elements discharged from the reprocessing plants. (author)

  3. Diet and scavenging habits of the smooth skate Dipturus innominatus.

    Science.gov (United States)

    Forman, J S; Dunn, M R

    2012-04-01

    The diet of smooth skate Dipturus innominatus was determined from examination of stomach contents of 321 specimens of 29·3-152·0 cm pelvic length, sampled from research and commercial trawlers at depths of 231-789 m on Chatham Rise, New Zealand. The diet was dominated by the benthic decapods Metanephrops challengeri and Munida gracilis, the natant decapod Campylonotus rathbunae and fishes from 17 families, of which hoki Macruronus novaezelandiae, sea perch Helicolenus barathri, various Macrouridae and a variety of discarded fishes were the most important. Multivariate analyses indicated the best predictors of diet variability were D. innominatus length and a spatial model. The diet of small D. innominatus was predominantly small crustaceans, with larger crustaceans, fishes and then scavenged discarded fishes increasing in importance as D. innominatus got larger. Scavenged discards were obvious as fish heads or tails only, or skeletal remains after filleting, often from pelagic species. Demersal fish prey were most frequent on the south and west Chatham Rise, in areas where commercial fishing was most active. Dipturus innominatus are highly vulnerable to overfishing, but discarding practices by commercial fishing vessels may provide a positive feedback to populations through improved scavenging opportunities. © 2012 NIWA. Journal of Fish Biology © 2012 The Fisheries Society of the British Isles.

  4. Body Size as a Driver of Scavenging in Theropod Dinosaurs.

    Science.gov (United States)

    Kane, Adam; Healy, Kevin; Ruxton, Graeme D; Jackson, Andrew L

    2016-06-01

    Theropod dinosaurs dominated Earth's terrestrial ecosystem as a diverse group of predators for more than 160 million years, yet little is known about their foraging ecology. Maintaining a balanced energy budget presented a major challenge for therapods, which ranged from the chicken-sized Microraptor up to the whale-sized Giganotosaurus, in the face of intense competition and the demands of ontogenetic growth. Facultative scavenging, a behavior present in almost all modern predators, may have been important in supplementing energetically expensive lifestyles. By using agent-based models based on the allometric relationship between size and foraging behaviors, we show that theropods between 27 and 1,044 kg would have gained a significant energetic advantage over individuals at both the small and large extremes of theropod body mass through their scavenging efficiency. These results were robust to rate of competition, primary productivity, and detection distance. Our models demonstrate the potential importance of facultative scavenging in theropods and the role of body size in defining its prevalence in Mesozoic terrestrial systems.

  5. Scavenger Receptor CD163 and Its Biological Functions

    Directory of Open Access Journals (Sweden)

    Gabriela Onofre

    2009-01-01

    Full Text Available CD163 is a member of scavenger receptor super family class B of the first subgroup. It is mapped to the region p13 on chromosome 12. Five different isoforms of CD163 have been described, which differ in the structure of their cytoplasmic domains and putative phosporylation sites. This scavenger receptor is selectively expressed on cells of monocytes and macrophages lineage exclusively. CD163 immunological function is essentially homeostatic. It also has other functions because participates in adhesion to endothelial cells, in tolerance induction and tissues regeneration. Other very important function of CD163 is the clearance of hemoglobin in its cell-free form and participation in anti-inflammation in its soluble form, exhibiting cytokine-like functions. We review the biological functions of CD163 which have been discovered until now. It seems apparent from this review that CD163 scavenger receptor can be used as biomarker in different diseases and as a valuable diagnostic parameter for prognosis of many diseases especially inflammatory disorders and sepsis.

  6. Shape similarities and differences in the skulls of scavenging raptors.

    Science.gov (United States)

    Guangdi, S I; Dong, Yiyi; Ma, Yujun; Zhang, Zihui

    2015-04-01

    Feeding adaptations are a conspicuous feature of avian evolution. Bill and cranial shape as well as the jaw muscles are closely related to diet choice and feeding behaviors. Diurnal raptors of Falconiformes exhibit a wide range of foraging behaviors and prey preferences, and are assigned to seven dietary groups in this study. Skulls of 156 species are compared from the dorsal, lateral and ventral views, by using geometric morphometric techniques with those landmarks capturing as much information as possible on the overall shape of cranium, bill, orbits, nostrils and attachment area for different jaw muscles. The morphometric data showed that the skull shape of scavengers differ significantly from other raptors, primarily because of different feeding adaptations. As a result of convergent evolution, different scavengers share generalized common morphology, possessing relatively slender and lower skulls, longer bills, smaller and more sideward orbits, and more caudally positioned quadrates. Significant phylogenetic signals suggested that phylogeny also played important role in shape variation within scavengers. New World vultures can be distinguished by their large nostrils, narrow crania and small orbits; Caracaras typically show large palatines, crania and orbits, as well as short, deep and sharp bill.

  7. Separation of nanoparticles: Filtration and scavenging from waste incineration plants.

    Science.gov (United States)

    Förster, Henning; Thajudeen, Thaseem; Funk, Christine; Peukert, Wolfgang

    2016-06-01

    Increased amounts of nanoparticles are applied in products of everyday life and despite material recycling efforts, at the end of their life cycle they are fed into waste incineration plants. This raises the question on the fate of nanoparticles during incineration. In terms of environmental impact the key question is how well airborne nanoparticles are removed by separation processes on their way to the bag house filters and by the existing filtration process based on pulse-jet cleanable fibrous filter media. Therefore, we investigate the scavenging and the filtration of metal nanoparticles under typical conditions in waste incineration plants. The scavenging process is investigated by a population balance model while the nanoparticle filtration experiments are realized in a filter test rig. The results show that depending on the particle sizes, in some cases nearly 80% of the nanoparticles are scavenged by fly ash particles before they reach the bag house filter. For the filtration step dust cakes with a pressure drop of 500Pa or higher are found to be very effective in preventing nanoparticles from penetrating through the filter. Thus, regeneration of the filter must be undertaken with care in order to guarantee highly efficient collection of particles even in the lower nanometre size regime. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. The evolution of the class A scavenger receptors

    Directory of Open Access Journals (Sweden)

    Whelan Fiona J

    2012-11-01

    Full Text Available Abstract Background The class A scavenger receptors are a subclass of a diverse family of proteins defined based on their ability to bind modified lipoproteins. The 5 members of this family are strikingly variable in their protein structure and function, raising the question as to whether it is appropriate to group them as a family based on their ligand binding abilities. Results To investigate these relationships, we defined the domain architecture of each of the 5 members followed by collecting and annotating class A scavenger receptor mRNA and amino acid sequences from publicly available databases. Phylogenetic analyses, sequence alignments, and permutation tests revealed a common evolutionary ancestry of these proteins, indicating that they form a protein family. We postulate that 4 distinct gene duplication events and subsequent domain fusions, internal repeats, and deletions are responsible for the diverse protein structures and functions of this family. Despite variation in domain structure, there are highly conserved regions across all 5 members, indicating the possibility that these regions may represent key conserved functional motifs. Conclusions We have shown with significant evidence that the 5 members of the class A scavenger receptors form a protein family. We have indicated that these receptors have a common origin which may provide insight into future functional work with these proteins.

  9. Preparation of epoxy-functionalized methyl methacrylate-butadiene-styrene core-shell particles and investigation of their dispersion in polyamide-6

    NARCIS (Netherlands)

    Aerdts, A.M.; Groeninckx, G.; Zirkzee, H.F.; Aert, van H.A.M.; Geurts, J.M.

    1997-01-01

    Functional core—shell impact modifiers of glycidyl methacrylate (GMA) functionalized methyl methacrylate—butadiene—styrene (MBS) have been prepared via a seeded semi-continuous emulsion polymerization. These functional MBS—GMA particles were blended with polyamide-6. Investigations by transmission

  10. Synthesis and characterization of soluble, blue-fluorescent polyamides and polyimides containing substituted p-terphenyl as well as long aliphatic segments in the main chain

    NARCIS (Netherlands)

    Mikroyannidis, JA; Tsivgoulis, GM

    1999-01-01

    A novel class of semiflexible polyamides and polyimides bearing substituted p-terphenyl as well as long aliphatic segments in the main chain were synthesized through pyrylium salts. Characterization of polymers was accomplished by inherent viscosity, elemental analysis, FT-IR, NMR, UV-vis

  11. Influence of properties and morphology of elastomeric phase on the behavior of ternary reactive blends of polyamide 6/rigid polymer/elastomer

    Czech Academy of Sciences Publication Activity Database

    Kelnar, Ivan; Kotek, Jiří; Munteanu, B. S.; Fortelný, Ivan

    2003-01-01

    Roč. 89, č. 13 (2003), s. 3647-3651 ISSN 0021-8995 R&D Projects: GA ČR GA106/01/0601 Institutional research plan: CEZ:AV0Z4050913 Keywords : polyamides * toughness * elastomers Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.017, year: 2003

  12. Integrated Analysis of the Scavenging Process in Marine Two-Stroke Diesel Engines

    DEFF Research Database (Denmark)

    Andersen, Fredrik Herland

    Large commercial ships such as container vessels and bulk carriers are propelledby low-speed, uniow scavenged two-stroke diesel engines. An integralin-cylinder process in this type of engine is the scavenging process, where the burned gases from the combustion process are evacuated through...... receiver fora two-stroke diesel engine. Time resolved boundary conditions corresponding to measurements obtained from an operating engine as well as realistic initial conditions are used in the simulations. The CFD model provides a detailed description of the in-cylinder ow from exhaust valve opening (EVO...... in the scavenge and exhaust receivers increase while the scavenge port exposure time, tscav, decrease. Further the scavenging pressure is varied while the engine speed is kept constant. From the perspective of the scavenging process this will resemble a load sweep following a generator curve. The scavenge port...

  13. A conceptual model for the understanding of fouling phenomenon when using triazine based H2S scavengers

    DEFF Research Database (Denmark)

    Madsen, Henrik Tækker; Søgaard, Erik Gydesen; Jensen, Carina

    2013-01-01

    -hydroxyethyl)-hexahydro-s-triazine and other triazines with hydroxy group functionality, the fouling has been found to be a dithiazine polymer, and the formation of this polymer has been explained by a model in which by products are formed alongside the general scavenging reaction. In this study we have...... studied the applicability of the previously suggested model to describe the reaction between 1,3,5-tri-(2-hydroxypropyl)-hexahydro-s-triazine and H2S. To investigate the reaction system, electrospray ionization mass spectrometry (ESI-MS) has been employed to analyse the composition of the generated...

  14. Liquid and Gas Permeation Studies on the Structure and Properties of Polyamide Thin-Film Composite Membranes

    KAUST Repository

    Duan, Jintang

    2014-01-01

    layer by gas adsorption and gas permeation measurements. Gas adsorption isotherms (N2 at 77K, CO2 at 273K) confirmed the microporous nature of PA in comparison with dense CTA and polysulfone materials. Gas permeation through the commercial PA

  15. Habitat of in vivo transformation influences the levels of free radical scavengers in Clinostomum complanatum: implications for free radical scavenger based vaccines against trematode infections.

    Science.gov (United States)

    Zafar, Atif; Rizvi, Asim; Ahmad, Irshad; Ahmad, Masood

    2014-01-01

    Since free radical scavengers of parasite origin like glutathione-S-transferase and superoxide dismutase are being explored as prospective vaccine targets, availability of these molecules within the parasite infecting different hosts as well as different sites of infection is of considerable importance. Using Clinostomum complanatum, as a model helminth parasite, we analysed the effects of habitat of in vivo transformation on free radical scavengers of this trematode parasite. Using three different animal models for in vivo transformation and markedly different sites of infection, progenetic metacercaria of C. complanatum were transformed to adult ovigerous worms. Whole worm homogenates were used to estimate the levels of lipid peroxidation, a marker of oxidative stress and free radical scavengers. Site of in vivo transformation was found to drastically affect the levels of free radical scavengers in this model trematode parasite. It was observed that oxygen availability at the site of infection probably influences levels of free radical scavengers in trematode parasites. This is the first report showing that habitat of in vivo transformation affects levels of free radical scavengers in trematode parasites. Since free radical scavengers are prospective vaccine targets and parasite infection at ectopic sites is common, we propose that infections at different sites, may respond differently to free radical scavenger based vaccines.

  16. Superhydrophilic Thin-Film Composite Forward Osmosis Membranes for Organic Fouling Control: Fouling Behavior and Antifouling Mechanisms

    KAUST Repository

    Tiraferri, Alberto

    2012-10-16

    This study investigates the fouling behavior and fouling resistance of superhydrophilic thin-film composite forward osmosis membranes functionalized with surface-tailored nanoparticles. Fouling experiments in both forward osmosis and reverse osmosis modes are performed with three model organic foulants: alginate, bovine serum albumin, and Suwannee river natural organic matter. A solution comprising monovalent and divalent salts is employed to simulate the solution chemistry of typical wastewater effluents. Reduced fouling is consistently observed for the superhydrophilic membranes compared to control thin-film composite polyamide membranes, in both reverse and forward osmosis modes. The fouling resistance and cleaning efficiency of the functionalized membranes is particularly outstanding in forward osmosis mode where the driving force for water flux is an osmotic pressure difference. To understand the mechanism of fouling, the intermolecular interactions between the foulants and the membrane surface are analyzed by direct force measurement using atomic force microscopy. Lower adhesion forces are observed for the superhydrophilic membranes compared to the control thin-film composite polyamide membranes. The magnitude and distribution of adhesion forces for the different membrane surfaces suggest that the antifouling properties of the superhydrophilic membranes originate from the barrier provided by the tightly bound hydration layer at their surface, as well as from the neutralization of the native carboxyl groups of thin-film composite polyamide membranes. © 2012 American Chemical Society.

  17. Superhydrophilic thin-film composite forward osmosis membranes for organic fouling control: fouling behavior and antifouling mechanisms.

    Science.gov (United States)

    Tiraferri, Alberto; Kang, Yan; Giannelis, Emmanuel P; Elimelech, Menachem

    2012-10-16

    This study investigates the fouling behavior and fouling resistance of superhydrophilic thin-film composite forward osmosis membranes functionalized with surface-tailored nanoparticles. Fouling experiments in both forward osmosis and reverse osmosis modes are performed with three model organic foulants: alginate, bovine serum albumin, and Suwannee river natural organic matter. A solution comprising monovalent and divalent salts is employed to simulate the solution chemistry of typical wastewater effluents. Reduced fouling is consistently observed for the superhydrophilic membranes compared to control thin-film composite polyamide membranes, in both reverse and forward osmosis modes. The fouling resistance and cleaning efficiency of the functionalized membranes is particularly outstanding in forward osmosis mode where the driving force for water flux is an osmotic pressure difference. To understand the mechanism of fouling, the intermolecular interactions between the foulants and the membrane surface are analyzed by direct force measurement using atomic force microscopy. Lower adhesion forces are observed for the superhydrophilic membranes compared to the control thin-film composite polyamide membranes. The magnitude and distribution of adhesion forces for the different membrane surfaces suggest that the antifouling properties of the superhydrophilic membranes originate from the barrier provided by the tightly bound hydration layer at their surface, as well as from the neutralization of the native carboxyl groups of thin-film composite polyamide membranes.

  18. Influence of the clay content and drying of successive no solvents change in the morphology of polyamide 6 / clay membranes

    International Nuclear Information System (INIS)

    Pereira, C.H.; Ferreira, R.S.B.; Bezerra, E.B.; Leite, A.M.D.; Araujo, E.D.; Lira, H.L.

    2014-01-01

    Membranes of polyamide 6/clay nanocomposites with different contents (1 and 3%) of Brazilian bentonite clay using the technique of phase inversion was obtained. The nanocomposites were obtained in a co-rotating twin screw extruder, by the melt intercalation method and were characterized by x-ray diffraction (XRD), which showed possibly an exfoliated and / or partially exfoliated structure was obtained. The membranes were dried at room temperature and also by successive exchange of non-solvents, to prevent collapse the pores using ethanol and n-hexane as a non-solvent. From the photomicrographs of top surface by scanning electron microscopy (SEM) showed to morphology change in the membranes from the presence of different clay contents as well as drying the same by successive exchange of non-solvents, obtaining membranes with larger amount of pores uniformly distributed. (author)

  19. Photo and Thermal Behavior of New Reinforced Polyamide-nanocomposite Montmorillonite on 2,3-Pyrazin Dicarboxylic Acid

    Science.gov (United States)

    Faghihi, Khalil; Samiei, Mojtaba; Hajibeygi, Mohsen

    2012-06-01

    Two new samples of reinforce polyamidemontmorillonite nanocomposites were synthesized by a convenient solution intercalation technique. Polyamide (PA) 3 as a source of polymer matrix was synthesized by the direct polycondensation reaction of pyrazine 2,3-dicarboxylic acid 1 with 4,4'-diamino diphenyl ether 2 in the presence of triphenyl phosphite (TPP), CaCl2, pyridine and N-methyl-2-pyrrolidone (NMP). The resulting nanocomposite films were characterized by Fourier transform infrared spectra (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). The results showed that organo-modified clay was dispersed homogeneously in PA matrix. TGA indicated an enhancement of thermal stability of new nanocomposites compared with the pure polymer.

  20. Direct assembly of in situ templated CdSe quantum dots via crystalline lamellae structure of polyamide 66

    Energy Technology Data Exchange (ETDEWEB)

    Cheval, Nicolas; Brooks, Richard [University of Nottingham, Division of Materials, Mechanics and Structures, Faculty of Engineering (United Kingdom); Fahmi, Amir, E-mail: Amir.Fahmi@hochschule-Rhein-waal.de [Rhein-Waal University of Applied Sciences, Faculty of Technology and Bionics (Germany)

    2012-03-15

    A simple concept is proposed for templating in situ synthesised CdSe quantum dots (QDs) into an organised nano-pattern using the crystalline lamellae structure of polyamide 66 (PA66). The morphology obtained for PA66 and the hybrid material on Si/SiO{sub x} solid substrate was characterised by means of atomic force microscope. Controlling the PA66 concentration in solution and the organic-inorganic interactions are found to be the keys factors to direct the assembly of CdSe QDs along the PA66 linear crystalline structure. This simple approach could be opened a new avenue for a large spectrum of innovative high-tech applications.

  1. Direct investigations of deformation and yield induced structure transitions in polyamide 6 below glass transition temperature with WAXS and SAXS

    DEFF Research Database (Denmark)

    Guo, Huilong; Wang, Jiayi; Zhou, Chengbo

    2015-01-01

    Deformation and yield induced structure transitions of polyamide 6 (PA6) were detected with the combination of the wide- and small-angle X-ray scattering (WAXS and SAXS) at 30 degrees C below glass transition temperature (T-g) of PA6. During deformation, gamma-alpha phase transition was found...... at elastic stage. The concentrated stress in crystals at elastic stage provided adequate energy for the direct gamma-alpha phase transition under T-g. The force to promote the gamma-phase into a phase directly is insufficient at the yield stage and a transient phase as a compromise was formed. The transient...... phase was confirmed by DSC measurements and assisted the gamma-alpha phase transition indirectly. The gamma-phase slips into incomplete fragments at yield point, and the parts along tensile direction are responsible for the formation of transient phase. The gamma-fragments after yield is oriented...

  2. Diet shift of a facultative scavenger, the wolverine, following recolonization of wolves.

    Science.gov (United States)

    van Dijk, Jiska; Gustavsen, Line; Mysterud, Atle; May, Roel; Flagstad, Øystein; Brøseth, Henrik; Andersen, Roy; Andersen, Reidar; Steen, Harald; Landa, Arild

    2008-11-01

    1. Wolves Canis lupus L. recolonized the boreal forests in the southern part of the Scandinavian peninsula during the late 1990s, but so far there has been little attention to its effect on ecosystem functioning. Wolf predation increases the availability of carcasses of large prey, especially moose Alces alces L., which may lead in turn to a diet switch in facultative scavengers such as the wolverine Gulo gulo L. 2. Using 459 wolverine scats collected during winter-spring 2001-04 for DNA identity and dietary contents, we compared diet inside and outside wolf territories while controlling for potential confounding factors, such as prey density. We tested the hypothesis that wolverine diet shifted towards moose in the presence of wolves, while taking into account possible sexual segregation between the sexes. Occurrence of reindeer, moose and small prey was modelled against explanatory covariates using logistic mixed-effects models. Furthermore, we compared diet composition and breadth among habitats and sexes. 3. Occurrence of reindeer, moose and small prey in the diet varied with prey availability and habitat. As expected, diet contained more moose and less reindeer and small prey in the presence of wolves. Their diet in tundra consisted of 40% reindeer Rangifer tarandus L., 39% moose and 9% rodents. In forest with wolf, their diet shifted to 76% moose, 18% reindeer and 5% rodents; compared to 42% moose, 32% reindeer and 15% rodents in forest without wolf. This diet switch could not be explained by higher moose density in wolf territories. Female diet consisted of more small prey than for males, but there was a tendency for females to use the highly available moose carrion opportunistically and to hunt less on small prey within wolf territories. 4. Our study highlights how wolves increase scavenging opportunities for wolverines, and how sexual differences in diet may also apply to large scavengers. Due to their more restricted home range, female wolverines are

  3. Recognition by nonaromatic and stereochemical subunit-containing polyamides of the four Watson-Crick base pairs in the DNA minor groove.

    Science.gov (United States)

    Zhang, Hong-Fei; Wu, Yan-Ling; Jiang, Shi-Kun; Wang, Pu; Sugiyama, Hiroshi; Chen, Xing-Lai; Zhang, Wen; Ji, Yan-Juan; Guo, Chuan-Xin

    2012-06-18

    In order to develop an optimal subunit as a T-recognition element in hairpin polyamides, 15 novel chirality-modified polyamides containing (R)-α,β-diaminopropionic acid ((R) β α-NH 2), (S)-α,β-diaminopropionic acid ((S) β α-NH 2), (1R,3S)-3-aminocyclopentanecarboxylic acid ((RS) Cp), (1S,3R)-3-amino-cyclopentanecarboxylic acid ((RS) Cp), (1R,3R)-3-aminocyclopentanecarboxylic acid ((RR) Cp) and (1S,3S)-3-amino-cyclopentanecarboxylic acid ((SS) Cp) residues were synthesized. Their binding characteristics to DNA sequences 5'-TGCNCAT-3'/3'-ACGN'GTA-5' (N⋅N'=A⋅T, T⋅A, G⋅C and C⋅G) were systemically studied by surface plasmon resonance (SPR) and molecular simulation (MSim) techniques. SPR showed that polyamide 4, AcIm-(S) β α-NH 2-ImPy-γ-ImPy-β-Py-βDp (β/(S) β α-NH 2 pair), bound to a DNA sequence containing a core binding site of 5'-TGCACAT-3' with a dissociation equilibrium constant (K(D) ) of 4.5×10(-8)  m. This was a tenfold improvement in specificity over 5'-TGCTCAT-3' (K(D) =4.5×10(-7)  M). MSim studies supported the SPR results. More importantly, for the first time, we found that chiral 3-aminocyclopentanecarboxylic acids in polyamides can be employed as base readers with only a small decrease in binding affinity to DNA. In particular, SPR showed that polyamide 9 ((RR) Cp/β pair) had a 15-fold binding preference for 5'-TGCTCAT-3' over 5'-TGCACAT-3'. A large difference in standard free energy change for A⋅T over T⋅A was determined (ΔΔG(o) =5.9 kJ mol(-1) ), as was a twofold decrease in interaction energy by MSim. Moreover, a 1:1 stoichiometry (9 to 5'-TGCTCAT-3'/3'-ACGAGTA-5') was shown by MSim to be optimal for the chiral five-membered cycle to fit the minor groove. Collectively, the study suggests that the (S)-α-amino-β-aminopropionic acid and (1R,3R)-3-aminocyclopentanecarboxylic acid can serve as a T-recognition element, and the stereochemistry and the nature of these subunits significantly influence

  4. How predictability of feeding patches affects home range and foraging habitat selection in avian social scavengers?

    Directory of Open Access Journals (Sweden)

    Sophie Monsarrat

    Full Text Available Feeding stations are commonly used to sustain conservation programs of scavengers but their impact on behaviour is still debated. They increase the temporal and spatial predictability of food resources while scavengers have supposedly evolved to search for unpredictable resources. In the Grands Causses (France, a reintroduced population of Griffon vultures Gyps fulvus can find carcasses at three types of sites: 1. "light feeding stations", where farmers can drop carcasses at their farm (spatially predictable, 2. "heavy feeding stations", where carcasses from nearby farms are concentrated (spatially and temporally predictable and 3. open grasslands, where resources are randomly distributed (unpredictable. The impact of feeding stations on vulture's foraging behaviour was investigated using 28 GPS-tracked vultures. The average home range size was maximal in spring (1272 ± 752 km(2 and minimal in winter (473 ± 237 km(2 and was highly variable among individuals. Analyses of home range characteristics and feeding habitat selection via compositional analysis showed that feeding stations were always preferred compared to the rest of the habitat where vultures can find unpredictable resources. Feeding stations were particularly used when resources were scarce (summer or when flight conditions were poor (winter, limiting long-ranging movements. However, when flight conditions were optimal, home ranges also encompassed large areas of grassland where vultures could find unpredictable resources, suggesting that vultures did not lose their natural ability to forage on unpredictable resources, even when feeding stations were available. However during seasons when food abundance and flight conditions were not limited, vultures seemed to favour light over heavy feeding stations, probably because of the reduced intraspecific competition and a pattern closer to the natural dispersion of resources in the landscape. Light feeding stations are interesting tools

  5. How predictability of feeding patches affects home range and foraging habitat selection in avian social scavengers?

    Science.gov (United States)

    Monsarrat, Sophie; Benhamou, Simon; Sarrazin, François; Bessa-Gomes, Carmen; Bouten, Willem; Duriez, Olivier

    2013-01-01

    Feeding stations are commonly used to sustain conservation programs of scavengers but their impact on behaviour is still debated. They increase the temporal and spatial predictability of food resources while scavengers have supposedly evolved to search for unpredictable resources. In the Grands Causses (France), a reintroduced population of Griffon vultures Gyps fulvus can find carcasses at three types of sites: 1. "light feeding stations", where farmers can drop carcasses at their farm (spatially predictable), 2. "heavy feeding stations", where carcasses from nearby farms are concentrated (spatially and temporally predictable) and 3. open grasslands, where resources are randomly distributed (unpredictable). The impact of feeding stations on vulture's foraging behaviour was investigated using 28 GPS-tracked vultures. The average home range size was maximal in spring (1272 ± 752 km(2)) and minimal in winter (473 ± 237 km(2)) and was highly variable among individuals. Analyses of home range characteristics and feeding habitat selection via compositional analysis showed that feeding stations were always preferred compared to the rest of the habitat where vultures can find unpredictable resources. Feeding stations were particularly used when resources were scarce (summer) or when flight conditions were poor (winter), limiting long-ranging movements. However, when flight conditions were optimal, home ranges also encompassed large areas of grassland where vultures could find unpredictable resources, suggesting that vultures did not lose their natural ability to forage on unpredictable resources, even when feeding stations were available. However during seasons when food abundance and flight conditions were not limited, vultures seemed to favour light over heavy feeding stations, probably because of the reduced intraspecific competition and a pattern closer to the natural dispersion of resources in the landscape. Light feeding stations are interesting tools for managing

  6. Wet scavenging of organic and elemental carbon during summer monsoon and winter monsoon seasons

    Science.gov (United States)

    Sonwani, S.; Kulshrestha, U. C.

    2017-12-01

    In the era of rapid industrialization and urbanization, atmospheric abundance of carbonaceous aerosols is increasing due to more and more fossil fuel consumption. Increasing levels of carbonaceous content have significant adverse effects on air quality, human health and climate. The present study was carried out at Delhi covering summer monsoon (July -Sept) and winter monsoon (Dec-Jan) seasons as wind and other meteorological factors affect chemical composition of precipitation in different manner. During the study, the rainwater and PM10 aerosols were collected in order to understand the scavenging process of elemental and organic carbon. The Rain water samples were collected on event basis. PM10 samples were collected before rain (PR), during rain (DR) and after rain (AR) during 2016-2017. The collected samples were analysed by the thermal-optical reflectance method using IMPROVE-A protocol. In PM10, the levels of organic carbon (OC) and its fractions (OC1, OC2, OC3 and OC4) were found significantly lower in the AR samples as compared to PR and DR samples. A significant positive correlation was noticed between scavenging ratios of organic carbon and rain intensity indicating an efficient wet removal of OC. In contrast to OCs, the levels of elemental carbon and its fractions (EC1, EC2, and EC3) in AR were not distinct during PR and DR. The elemental carbon showed very week correlation with rain intensity in Delhi region which could be explained on the basis of hydrophobic nature of freshly emitted carbon soot. The detailed results will be discussed during the conference.

  7. Energy scavenging system by acoustic wave and integrated wireless communication

    Science.gov (United States)

    Kim, Albert

    The purpose of the project was developing an energy-scavenging device for other bio implantable devices. Researchers and scientist have studied energy scavenging method because of the limitation of traditional power source, especially for bio-implantable devices. In this research, piezoelectric power generator that activates by acoustic wave, or music was developed. Follow by power generator, a wireless communication also integrated with the device for monitoring the power generation. The Lead Zirconate Titanate (PZT) bimorph cantilever with a proof mass at the free end tip was studied to convert acoustic wave to power. The music or acoustic wave played through a speaker to vibrate piezoelectric power generator. The LC circuit integrated with the piezoelectric material for purpose of wireless monitoring power generation. However, wireless monitoring can be used as wireless power transmission, which means the signal received via wireless communication also can be used for power for other devices. Size of 74 by 7 by 7cm device could generate and transmit 100mVp from 70 mm distance away with electrical resonant frequency at 420.2 kHz..

  8. Phytoconstituents with Radical Scavenging and Cytotoxic Activities from Diospyros shimbaensis

    Directory of Open Access Journals (Sweden)

    Per Aronsson

    2016-01-01

    Full Text Available As part of our search for natural products having antioxidant and anticancer properties, the phytochemical investigation of Diospyros shimbaensis (Ebenaceae, a plant belonging to a genus widely used in East African traditional medicine, was carried out. From its stem and root barks the new naphthoquinone 8,8′-oxo-biplumbagin (1 was isolated along with the known tetralones trans-isoshinanolone (2 and cis-isoshinanolone (3, and the naphthoquinones plumbagin (4 and 3,3′-biplumbagin (5. Compounds 2, 4, and 5 showed cytotoxicity (IC50 520–82.1 μM against MDA-MB-231 breast cancer cells. Moderate to low cytotoxicity was observed for the hexane, dichloromethane, and methanol extracts of the root bark (IC50 16.1, 29.7 and > 100 μg/mL, respectively, and for the methanol extract of the stem bark (IC50 59.6 μg/mL. The radical scavenging activity of the isolated constituents (1–5 was evaluated on the 2,2-diphenyl-1-picrylhydrazyl (DPPH radical scavenging assay. The applicability of the crude extracts and of the isolated constituents for controlling degenerative diseases is discussed.

  9. Phytoconstituents with Radical Scavenging and Cytotoxic Activities from Diospyros shimbaensis.

    Science.gov (United States)

    Aronsson, Per; Munissi, Joan J E; Gruhonjic, Amra; Fitzpatrick, Paul A; Landberg, Göran; Nyandoro, Stephen S; Erdelyi, Mate

    2016-01-15

    As part of our search for natural products having antioxidant and anticancer properties, the phytochemical investigation of Diospyros shimbaensis (Ebenaceae), a plant belonging to a genus widely used in East African traditional medicine, was carried out. From its stem and root barks the new naphthoquinone 8,8'-oxo-biplumbagin ( 1 ) was isolated along with the known tetralones trans -isoshinanolone ( 2 ) and cis -isoshinanolone ( 3 ), and the naphthoquinones plumbagin ( 4 ) and 3,3'-biplumbagin ( 5 ). Compounds 2 , 4 , and 5 showed cytotoxicity (IC 50 520-82.1 μM) against MDA-MB-231 breast cancer cells. Moderate to low cytotoxicity was observed for the hexane, dichloromethane, and methanol extracts of the root bark (IC 50 16.1, 29.7 and > 100 μg/mL, respectively), and for the methanol extract of the stem bark (IC 50 59.6 μg/mL). The radical scavenging activity of the isolated constituents ( 1 - 5 ) was evaluated on the 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging assay. The applicability of the crude extracts and of the isolated constituents for controlling degenerative diseases is discussed.

  10. Influence of intense scavenging on Pa-Th fractionation in the wake of Kerguelen Island (Southern Ocean

    Directory of Open Access Journals (Sweden)

    C. Venchiarutti

    2011-11-01

    Full Text Available Dissolved and particulate excess 230Th and 231Pa concentrations (noted 230Thxs and 231Paxs respectively and 231Paxs/230Thxs activity ratios were investigated on and out of the Kerguelen plateau (Southern Ocean in the framework of the Kerguelen Ocean and Plateau compared Study project in order to better understand the influence of particle flux and particle chemistry and advection on the scavenging of 231Pa.

    In the wake of Kerguelen, particulate 231Paxs is relatively abundant compared to its content in the dissolved phase. This, together with the low fractionation observed between 230Th and 231Pa (FTh/Pa ranging from 0.06 ± 0.01 to 1.6 ± 0.2 reflects the domination of the biogenic silica in the particle pool.

    Along the eastern escarpment of the Kerguelen plateau, the strong 231Paxs horizontal gradient in the deep waters highlights the intense removal of 231Pa at depth, as already observed for 230Thxs. This local boundary scavenging was attributed to re-suspension of opal-rich particles by nepheloid layers, resulting in fractionation factors FTh/Pa ≤ 1 along the Kerguelen plateau slope. Therefore, both the composition (biogenic opal and the flux (intense along the margin of particles control the scavenging of the two radionuclides in the Kerguelen wake.

    The modelling of 231Pa distribution with an advection-scavenging model demonstrates that lateral advection of open ocean water on the Kerguelen plateau could supply most of the 231Pa, which is then efficiently scavenged on the highly productive plateau, as previously proposed for 230Thxs. It stresses that lateral advection can play a significant role in the overall

  11. Occurrence and distribution of nitrogen-scavenging bacteria in marine environment

    OpenAIRE

    Sugahara, Isao; Kimura, Toshio; Hayashi, Koichiro

    1987-01-01

    The occurrence and distribution nitrogen-scavenging bacteria in the water of coastal and oceanic of Japan were studied during the Seisui-Maru cruises from 1986 to 1987. Nitroben-scavenging bacteria in the water usually occurred at the level of 10-104 cfu/ml.This value was almost comparable to that of aerobic heterotrophic bacteria. It seems that nitrogen-scavenging bacteria play an important role in the efficient uptake of low levels of nitrogenous compounds in marine enviroment.

  12. Anchoring ceria nanoparticles on graphene oxide and their radical scavenge properties under gamma irradiation environment.

    Science.gov (United States)

    Xia, Wei; Zhao, Jun; Wang, Tao; Song, Li; Gong, Hao; Guo, Hu; Gao, Bing; Fan, Xiaoli; He, Jianping

    2017-06-28

    Polymer networks such as those of epoxy resin, as common protection materials, possess radiolytic oxidation degradation effects under gamma irradiation environment, which have a great accelerating effect on the ageing rate and severely limit their potential applications for metal protection in the nuclear industry. To overcome this, we report a simple scheme of anchoring crystalline ceria nanoparticles onto graphene sheets (CG) and incorporate it into the epoxy resin, followed by thermal polymerization to obtain CeO 2 /graphene-epoxy nanocomposite coating (CGNS). We had proven that graphene might act as "interwalls" in the epoxy matrix, which will result in space location-obstruct effect as well as absorb the radicals induced by γ-ray irradiation. Moreover, owing to the interconversion of cerium ions between their +3 and +4 states coupled with the formation of oxygen vacancy defects, electron spin resonance (ESR) detection shows that CeO 2 /graphene (CG) could act as a preferable radical scavenger and achieve better performance in trapping radicals than single graphene based composite. Electrochemical data strongly demonstrate that CeO 2 /graphene is capable of maintaining the anti-corrosion properties under gamma irradiation environment. Therefore, the designed hybrid CeO 2 /graphene-epoxy composite can be considered as potential candidates for protective coatings in nuclear industry.

  13. Physicochemical characterisation and radical-scavenging activity of Cucurbitaceae seed oils.

    Science.gov (United States)

    Jorge, Neuza; da Silva, Ana Carolina; Malacrida, Cassia Roberta

    2015-01-01

    Oils extracted from Cucurbitaceae seeds were characterised for their fatty acid and tocopherol compositions. In addition, some physicochemical characteristics, total phenolic contents and the radical-scavenging activities were determined. Oil content amounted to 23.9% and 27.1% in melon and watermelon seeds, respectively. Physicochemical characteristics were similar to those of other edible oils and the oils showed significant antioxidant activities. Fatty acid composition showed total unsaturated fatty acid content of 85.2-83.5%, with linoleic acid being the dominant fatty acid (62.4-72.5%), followed by oleic acid (10.8-22.7%) and palmitic acid (9.2-9.8%). The oils, especially watermelon seed oil, showed high total tocopherol and phenolic contents. The γ-tocopherol was the predominant tocopherol in both oils representing 90.9 and 95.6% of the total tocopherols in melon and watermelon seed oils, respectively. The potential utilisation of melon and watermelon seed oils as a raw material for food, chemical and pharmaceutical industries appears to be favourable.

  14. Chemical constituents, radical scavenging activity and enzyme inhibitory capacity of fruits from Cotoneaster pannosus Franch.

    Science.gov (United States)

    Les, Francisco; López, Víctor; Caprioli, Giovanni; Iannarelli, Romilde; Fiorini, Dennis; Innocenti, Marzia; Bellumori, Maria; Maggi, Filippo

    2017-05-24

    Cotoneaster pannosus (Rosaceae) is a semievergreen shrub, producing globose dark red pomes, native to China and widely used as an ornamental plant all over the world. Despite its extensive cultivation, little information is available on the chemical composition and biological activities of its fruits. In this work, the analysis of the chemical composition of C. pannosus fruits, in terms of phenolic components, carotenoids and ascorbic acid by HPLC/DAD, HPLC/ESI-MS and MS/MS as well as in terms of macro- and micro-nutrients was performed. The fruits proved to be a good source of shikimic acid and caffeoylquinic acids, whereas β-carotene, pelargonidin-3-O glucoside and cyanidin-3,5-rutinoside gave an important contribution to the color of the fruit. Both the polar and apolar fruit extracts showed noteworthy radical scavenger activity and inhibitory effects against monoamine oxidase A (MAO-A), tyrosinase (TYR) and α-glucosidase, making C. pannosus red pomes a promising candidate ingredient in functional foods and dietary supplements.

  15. Scavenging efficiency and red fox abundance in Mediterranean mountains with and without vultures

    Science.gov (United States)

    Morales-Reyes, Zebensui; Sánchez-Zapata, José A.; Sebastián-González, Esther; Botella, Francisco; Carrete, Martina; Moleón, Marcos

    2017-02-01

    Vertebrate scavenging assemblages include two major functional groups: obligate scavengers (i.e., vultures), which depend totally on carrion and are undergoing severe declines around the globe, and facultative scavengers, which exploit carrion opportunistically and are generally ubiquitous. Our goal was to investigate the hypothesis that vultures can indirectly regulate the abundance of mesopredators (i.e., facultative scavengers) through modulating their access to carrion resources. We studied scavenging efficiency and red fox (Vulpes vulpes) abundance in two neighbouring areas of South-eastern Spain where vultures (mainly griffon vultures Gyps fulvus) are present (Cazorla) and absent (Espuña). To do so, we monitored ungulate carcasses consumption during winter and summer, and counted red fox scats along walking transects as a proxy of fox density. Our results confirmed that scavenging efficiency was higher in Cazorla and in carcasses visited by vultures. This resulted in increasing scavenging opportunities for facultative scavengers where vultures were absent. Accordingly, mean red fox abundance was higher in Espuña. These results suggest the existence of a vulture-mediated mesopredator release (i.e., an increase of mesopredator numbers following vulture loss), which could trigger important indirect ecological effects. Also, our study demonstrates that facultative scavengers are hardly able to functionally replace vultures, mainly because the former exploit carrion on a slower time scale.

  16. Optical and Thermal Behaviors of Polyamide-Layered Silicate Nanocomposites Based on 4,4'-Azodibenzoic Acid by Solution Intercalation Technique

    Science.gov (United States)

    Faghihi, Khalil; Shabanian, Meisam

    2011-04-01

    Two new samples of polyamide-montmorillonite reinforced nanocomposites based on 4,4'-azodibenzoic acid were prepared by a convenient solution intercalation technique. Polyamide (PA) 4 as a source of polymer matrix was synthesized by the direct polycondensation reaction of 4,4'-azodibenzoic acid 2 with 4,4'-diamino diphenyl sulfone 3 in the presence of triphenyl phosphate (TPP), CaCl2, pyridine and N-methyl-2-pyrrolidone (NMP). Morphology and structure of the resulting PA-nanocomposite films 4a and 4b with 10 and 20% silicate particles were characterized by FTIR spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The effect of clay dispersion and the interaction between clay and polymeric chains on the properties of nanocomposite films were investigated by using Uv-vis spectroscopy, thermogravimetric analysis (TGA) and water uptake measurements.

  17. Isolation and identification of arctiin and arctigenin in leaves of burdock (Arctium lappa L.) by polyamide column chromatography in combination with HPLC-ESI/MS.

    Science.gov (United States)

    Liu, Shiming; Chen, Kaoshan; Schliemann, Willibald; Strack, Dieter

    2005-01-01

    A simple method involving polyamide column chromatography in combination with HPLC-PAD and HPLC-ESI/MS for isolating and identifying two kinds of lignans, arctiin and arctigenin, in the leaves of burdock (Arctium lappa L.) has been established. After extraction of burdock leaves with 80% methanol, the aqueous phase of crude extracts was partitioned between water and chloroform and the aqueous phase was fractionated on a polyamide glass column. The fraction, eluting with 100% methanol, was concentrated and gave a white precipitate at 4 degrees C from which two main compounds were purified by semi-preparative HPLC. In comparison with the UV and ESI-MS spectra and the HPLC retention time of authentic standards, the compounds were determined to be arctiin and arctigenin. The extraction/separation technique was validated using an internal standard method.

  18. Evaluation of impact strength of polyamide 6/bentonite clay nanocomposites; Avaliacao da resistencia mecanica sob impacto de nanocompositos de poliamida 6/argila bentonitica

    Energy Technology Data Exchange (ETDEWEB)

    Paz, Rene A.; Leite, Amanda M.D.; Medeirosa, Vanessa da N., E-mail: rene@cct.ufcg.edu.b [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Curso de Pos-Graduacao em Ciencia e Engenharia de Materiais; Araujo, Edcleide M.; Melo, Tomas J.A. [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Dept. de Engenharia de Materiais; Pessan, Luiz A. [Universidade Federal de Sao Carlos (DEMa/UFSCAR), SP (Brazil). Dept. de Engenharia de Materiais

    2010-07-01

    Nanocomposites of polymer/clay have had much attention in recent years, particularly those developed with layered silicates due to the need of engineering materials more efficient than pure polymers for certain applications. The level of exfoliation of layered silicates in crystalline structure of polymer matrices has been studied and has been observed that they affect the crystalline behavior and the physical and mechanical properties. In this study, nanocomposites of polyamide 6 were obtained by the melt intercalation method, using a regional bentonite modified with a quaternary ammonium salt in an amount of 3% by weight. XRD results showed that incorporation of salt among the layers of clay, making it organophilic and obtaining exfoliated and/or partially exfoliated structures. The impact properties of the nanocomposites showed inferior in relation to pure polyamide, in other words, lost of toughness. (author)

  19. Study of the radiation effect on the mechanical properties of flammability and the glow wire of polyamide 6.6 with and without fiber glass reinforcement

    International Nuclear Information System (INIS)

    Ferro, Waldir Pedro; Silva, Leonardo Gondim de Andrade e

    2002-01-01

    The Automotive, Electric and Electronic Component Industry, more and more employ the Engineering Plastic as a viable alternative for the reduction of costs and increase of productivity without loss of quality. Polyamide 6.6 is an Engineering Plastic with distinguished role on this category of polymers due to its high thermal and chemical resistances and strength. The aim of this work is to present the results of Tensile Strength, Flexural Strength and Izod Notched Impact Strength as well as thermal experiments of Flammability (Automotive and Electronic Components Industry) and of Glow Wire (Electric Components Industry) of Polyamide 6.6 with or without Fiber Glass reinforcement, irradiated by Electron Beams in different doses. (author)

  20. A New Flame-Retardant Polyamide Containing Phosphine Oxide and N,N-(4,4-diphenylether) Moieties in the Main Chain: Synthesis and Characterization

    OpenAIRE

    FAGHIHI, Khalil

    2014-01-01

    A new flame-retardant polyamide containing phosphine oxide moieties in the main chain was synthesized from the solution polycondensation reaction of bis(3-aminophenyl) phenyl phosphine oxide with N,N-(4,4-diphenylether) bis trimellitimide, using thionyl chloride, N-methyl-2-pyrolidone, and pyridine as condensing agents. This new polymer was obtained in high yield (92%), has high inherent viscosity (0.73 dL/g), and was characterized by elemental analysis, FT-IR spectroscopy, thermal gr...

  1. Energy scavenging sensors for ultra-low power sensor networks

    Science.gov (United States)

    O'Brien, Dominic C.; Liu, Jing Jing; Faulkner, Grahame E.; Vachiramon, Pithawat; Collins, Steve; Elston, Steven J.

    2010-08-01

    The 'internet of things' will require very low power wireless communications, preferably using sensors that scavenge power from their environment. Free space optics allows communications over long ranges, with simple transceivers at each end, offering the possibility of low energy consumption. In addition there can be sufficient energy in the communications beam to power simple terminals. In this paper we report experimental results from an architecture that achieves this. A base station that tracks sensors in its coverage area and communicates with them using low divergence optical beams is presented. Sensor nodes use modulated retro-reflectors to communicate with the base station, and the nodes are powered by the illuminating beam. The paper presents design and implementation details, as well as future directions for this work.

  2. The energy stabilization for the SLC scavenger beam

    International Nuclear Information System (INIS)

    Hsu, I.; Browne, M.; Himel, T.; Humphrey, R.; Jobe, K.; Ross, M.; Pellegrin, J.L.; Seeman, J.

    1991-01-01

    The energy of the SLC scavenger beam which is used to produce positrons must be carefully maintained so that the beam can be transported through the collimators in the dispersive region of the extraction line which leads from the Linac to the positron target. A feedforward control loop has been developed to compensate the energy fluctuations due to the beam intensity fluctuations. The loop detects the beam intensities in the damping rings and then calculates how much energy needs to be compensated due to beam loading effects. The energy is corrected by adjusting the acceleration phases of two sets of klystrons right before the extraction. Because there is feedback loop using the same controls, their interaction needs to be carefully treated. This paper presents an overview of the feedforward algorithms

  3. The energy stabilization for the SLC scavenger beam

    International Nuclear Information System (INIS)

    Hsu, Ian; Browne, M.; Himel, T.; Humphrey, R.; Jobe, K.; Ross, M.; Pellegrin, J.L.; Seeman, J.

    1990-08-01

    The energy of the SLC scavenger beam which is used to produce positrons must be carefully maintained so that the beam can be transported through the collimators in the dispersive region of the extraction line which leads from the Linac to the positron target. A feedforward control loop has been developed to compensate the energy fluctuations due to the beam intensity fluctuations. The loop detects the beam intensities in the damping rings and then calculates how much energy needs to be compensated due to beam loading effects. The energy is corrected by adjusting the acceleration phases of two sets of klystrons right before the extraction. Because there is feedback loop using the same controls, their interaction needs to be carefully treated. This paper presents an overview of the feedforward algorithms. 3 figs

  4. Scavenger Receptor Structure and Function in Health and Disease

    Directory of Open Access Journals (Sweden)

    Izma Abdul Zani

    2015-05-01

    Full Text Available Scavenger receptors (SRs are a ‘superfamily’ of membrane-bound receptors that were initially thought to bind and internalize modified low-density lipoprotein (LDL, though it is currently known to bind to a variety of ligands including endogenous proteins and pathogens. New family of SRs and their properties have been identified in recent years, and have now been classified into 10 eukaryote families, defined as Classes A-J. These receptors are classified according to their sequences, although in each class they are further classified based in the variations of the sequence. Their ability to bind a range of ligands is reflected on the biological functions such as clearance of modified lipoproteins and pathogens. SR members regulate pathophysiological states including atherosclerosis, pathogen infections, immune surveillance, and cancer. Here, we review our current understanding of SR structure and function implicated in health and disease.

  5. Biomimetic Composite-Metal Hip Resurfacing Implant

    Directory of Open Access Journals (Sweden)

    Habiba Bougherara

    2008-01-01

    Full Text Available Hip resurfacing technique is a conservative arthroplasty used in the young patient in which the femoral head is reshaped to accept metal cap with small guide stem. In the present investigation, a hybrid composite-metal resurfacing implant is proposed. The cup is made of carbon fiber/polyamide 12 (CF/PA12 covered with a thin layer of cobalt chrome (Co-Cr. Finite element (FE method was applied to analyze and compare the biomechanical performances of the hybrid hip resurfacing (HHR and the conventional Birmingham (BHR. Results of the finite element analysis showed that the composite implant leads to an increase in stresses in the cancellous bone by more than 15% than BHR, indicating a lower potential for stress shielding and bone fracture and higher potential for bone apposition with the HHR.

  6. Polyamide nanocapsules and nano-emulsions containing Parsol® MCX and Parsol® 1789: in vitro release, ex vivo skin penetration and photo-stability studies.

    Science.gov (United States)

    Hanno, Ibrahim; Anselmi, Cecilia; Bouchemal, Kawthar

    2012-02-01

    To prepare polyamide nanocapsules for skin photo-protection, encapsulating α-tocopherol, Parsol®MCX (ethylhexyl methoxycinnamate) and/or Parsol®1789 (butyl methoxydibenzoylmethane). Nanocapsules were obtained by combining spontaneous emulsification and interfacial polycondensation reaction between sebacoyl chloride and diethylenetriamine. Nano-emulsions used as control were obtained by the same process without monomers. The influence of carrier on release rate was studied in vitro with a membrane-free model. Epidermal penetration of encapsulated sunscreens was ex vivo evaluated using Franz diffusion cells. Ability of encapsulated sunscreens to improve photo-stability was verified by comparing percentage of degradation after UV radiation exposure. Sunscreen-containing nanocapsules (260-400 nm) were successfully prepared; yield of encapsulation was >98%. Parsol®MCX and Parsol®1789 encapsulation led to decreased release rate by up to 60% in comparison with nano-emulsion and allowed minimum penetration through pig ear epidermis. Presence of polyamide shell protected encapsulated sunscreen filters from photo-degradation without affecting their activity. Encapsulation of Parsol®MCX and Parsol®1789 into oil-core of polyamide nanocapsules allowed protection from photo-degradation, controlled release from nanocapsules, and limited penetration through pig ear epidermis.

  7. Missing facial parts computed by a morphable model and transferred directly to a polyamide laser-sintered prosthesis: an innovation study.

    Science.gov (United States)

    Mueller, A A; Paysan, P; Schumacher, R; Zeilhofer, H-F; Berg-Boerner, B-I; Maurer, J; Vetter, T; Schkommodau, E; Juergens, P; Schwenzer-Zimmerer, K

    2011-12-01

    Mirroring of missing facial parts and rapid prototyping of templates have become widely used in the manufacture of prostheses. However, mirroring is not applicable for central facial defects, and the manufacture of a template still requires labour-intensive transformation into the final facial prosthesis. We have explored innovative techniques to meet these remaining challenges. We used a morphable model of a face for the reconstruction of missing facial parts that did not have mirror images, and skin-coloured polyamide laser sintering for direct manufacture of the prosthesis. From the knowledge gleaned from a data set of 200 coloured, three-dimensional scans, we generated a missing nose that was statistically compatible with the remaining parts of the patient's face. The planned prosthesis was manufactured directly from biocompatible skin-coloured polyamide powder by selective laser sintering, and the prosthesis planning system produced a normal-looking reconstruction. The polyamide will need adjustable colouring, and we must be able to combine it with a self-curing resin to fulfil the requirements of realistic permanent use. Copyright © 2011 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  8. Novel Organic Phototransistor-Based Nonvolatile Memory Integrated with UV-Sensing/Green-Emissive Aggregation Enhanced Emission (AEE)-Active Aromatic Polyamide Electret Layer.

    Science.gov (United States)

    Cheng, Shun-Wen; Han, Ting; Huang, Teng-Yung; Chang Chien, Yu-Hsin; Liu, Cheng-Liang; Tang, Ben Zhong; Liou, Guey-Sheng

    2018-05-30

    A novel aggregation enhanced emission (AEE)-active polyamide TPA-CN-TPE with a high photoluminesence characteristic was successfully synthesized by the direct polymerization of 4-cyanotriphenyl diamine (TPA-CN) and tetraphenylethene (TPE)-containing dicarboxylic acid. The obtained luminescent polyamide plays a significant role as the polymer electret layer in organic field-effect transistors (OFETs)-type memory. The strong green emission of TPA-CN-TPE under ultraviolet (UV) irradiation can be directly absorbed by the pentacene channel, displaying a light-induced programming and voltage-driven erasing organic phototransistor-based nonvolatile memory. Memory window can be effectively manipulated between the programming and erasing states by applying UV light illumination and electrical field, respectively. The photoinduced memory behavior can be maintained for over 10 4 s between these two states with an on/off ratio of 10 4 , and the memory switching can be steadily operated for many cycles. With high photoresponsivity ( R) and photosensitivity ( S), this organic phototransistor integrated with AEE-active polyamide electret layer could serve as an excellent candidate for UV photodetectors in optical applications. For comparison, an AEE-inactive aromatic polyimide TPA-PIS electret with much weaker solid-state emission was also applied in the same OFETs device architecture, but this device did not show any UV-sensitive and UV-induced memory characteristics, which further confirmed the significance of the light-emitting capability of the electret layer.

  9. Molecular Mechanisms behind Free Radical Scavengers Function against Oxidative Stress

    Directory of Open Access Journals (Sweden)

    Fereshteh Ahmadinejad

    2017-07-01

    Full Text Available Accumulating evidence shows that oxidative stress is involved in a wide variety of human diseases: rheumatoid arthritis, Alzheimer’s disease, Parkinson’s disease, cancers, etc. Here, we discuss the significance of oxidative conditions in different disease, with the focus on neurodegenerative disease including Parkinson’s disease, which is mainly caused by oxidative stress. Reactive oxygen and nitrogen species (ROS and RNS, respectively, collectively known as RONS, are produced by cellular enzymes such as myeloperoxidase, NADPH-oxidase (nicotinamide adenine dinucleotide phosphate-oxidase and nitric oxide synthase (NOS. Natural antioxidant systems are categorized into enzymatic and non-enzymatic antioxidant groups. The former includes a number of enzymes such as catalase and glutathione peroxidase, while the latter contains a number of antioxidants acquired from dietary sources including vitamin C, carotenoids, flavonoids and polyphenols. There are also scavengers used for therapeutic purposes, such as 3,4-dihydroxyphenylalanine (L-DOPA used routinely in the treatment of Parkinson’s disease (not as a free radical scavenger, and 3-methyl-1-phenyl-2-pyrazolin-5-one (Edaravone that acts as a free radical detoxifier frequently used in acute ischemic stroke. The cell surviving properties of L-DOPA and Edaravone against oxidative stress conditions rely on the alteration of a number of stress proteins such as Annexin A1, Peroxiredoxin-6 and PARK7/DJ-1 (Parkinson disease protein 7, also known as Protein deglycase DJ-1. Although they share the targets in reversing the cytotoxic effects of H2O2, they seem to have distinct mechanism of function. Exposure to L-DOPA may result in hypoxia condition and further induction of ORP150 (150-kDa oxygen-regulated protein with its concomitant cytoprotective effects but Edaravone seems to protect cells via direct induction of Peroxiredoxin-2 and inhibition of apoptosis.

  10. Study of atmospheric pollution scavenging. Seventeenth progress report

    Energy Technology Data Exchange (ETDEWEB)

    Semonin, R.G.; Bartlett, J.; Gatz, D.F.; Peden, M.E.; Skowron, L.M.; Stensland, G.J.

    1979-07-01

    The continued study of historical precipitation chemistry, air quality, and emissions data shows that the nitrate concentrations in precipitation have increased over the past 20 years with little change in sulfate concentrations. An analysis of aerosol concentrations at MAP3S precipitation collection sites shows consistently higher elemental concentrations at urban Champaign, Illinois, than sites at Whiteface Mountain, New York, and rural Champaign. Scavenging ratios at Whiteface exceeded those obtained previously at St. Louis, Missouri, possibly due to mid-tropospheric long-range transport and differing synoptic situations. Factor analysis of 6 storms during METROMEX shows that different deposition patterns were found for the soluble and insoluble concentrations of the same element. This suggests different scavenging processes may be active for these fractions. Using METROMEX data, no correlation was found between pollutant source strength and the urban-related precipitation anomaly. Four different Nuclepore air filter setups were used to compare air concentrations of sulfate, nitrate, and ammonium. The sulfate comparison was good, but the large variability for nitrate and ammonium raise serious questions on the credibility of measurements using Nuclepore as the collection medium. The details of a case study of wet deposition from SCORE-78 are presented and shows the pollutant concentrations are more variable than the rainfall. A brief description of the progress on the SCORE-79 project is presented. The progress on acid rainfall studies shows that the high pH values in the Midwest in the mid-1950's were due in part to elevated concentrations of calcium and magnesium. A variety of model calculations are presented to show the effects of adjusting past data to currently observed values. Recent results of continuing research on ionic stability of precipitation samples are given.

  11. Characterization of fatty acids, bioactive lipids, and radical scavenging activity of Canterbury bells seed oil

    Directory of Open Access Journals (Sweden)

    Hassanien, M. F.R.

    2014-06-01

    Full Text Available The aim of this study was to characterize the chemical composition and radical scavenging activity of Canterbury bells (Campanula medium seed oil. C. medium seeds contained 9.2% extractable oil. The lipid classes, fatty acids, phytosterol and tocopherol composition of C. medium seed oil were determined. The amount of neutral lipids in the oil was the highest, followed by glycolipids and phospholipids. Linoleic and oleic were the main fatty acids. C. medium oil is characterized by high levels of phytosterols and β-sitosterol was the main compound. β-Tocopherol constituted 42.5% of the total tocopherol content followed by γ-tocopherol. The radical scavenging activity (RSA toward 1,1-diphenyl-2-picrylhydrazyl (DPPH radicals and galvinoxyl radicals of C. medium oil were higher than those of extra virgin olive oil. The diverse potential uses of C. medium oil may make this plant industrially important.El objetivo de este estudio fue caracterizar la composición química y la actividad de captación de radicales de aceites de semillas de campanillas de Canterbury (Campanula medium. Las semillas de C. medium contenían 9,2 % de aceite extraíble. Se determinó la composición de las diferentes clases de lípidos, ácidos grasos, fitoesteroles y tocoferoles. La cantidad de lípidos neutros en el aceite fue mayoritario, seguido de glicolípidos y fosfolípidos. Linoleico y oleico fueron los ácidos grasos principales. El aceite de C. medium se caracteriza por altos niveles de fitoesteroles y β-sitosterol fue el compuesto principal. β-tocoferol constituía 42,5 % del contenido total de tocoferol seguido de γ-tocoferol. La actividad de captación de radicales (RSA a 1,1-difenil-2- picrilhidrazil (DPPH y radicales galvinoxil de C. medium fueron superiores a las de aceite de oliva virgen extra. Los diversos usos potenciales de los aceites de C. medium pueden hacer que esta planta pueda ser importante industrialmente.

  12. Influence of various scavengers of •OH radicals on the radiation sensitivity of yeast and bacteria.

    Science.gov (United States)

    Múčka, Viliam; Bláha, Pavel; Čuba, Václav; Červenák, Jaroslav

    2013-12-01

    To quantitatively investigate the influence of various •OH (hydroxyl radical) scavengers on the radiation sensitivity of yeast and bacteria, particularly to define the relationship between the protective effect of a scavenger and its •OH scavenging efficiency. In order to study the protective effect of •OH scavengers we used various concentrations of four scavengers (methanol, potassium formate, ethanol and ascorbic acid) in isotonic salt solutions. These solutions containing live yeast (Saccharomyces cerevisiae) or bacteria (Escherichia coli) were irradiated with (60)Co isotope γ -radiation using two different doses and dose rates. The number of surviving cells was determined prior to and after irradiation both in suspension with and without scavengers. The surviving fractions after irradiation with and without the scavenger were evaluated. The main results of the paper were: The surviving fraction increased approximately linearly within the measured interval with increasing concentration of the scavenger. The same dependences were found for the protecting effect depending on the scavenging efficiency. The slopes of these dependences (k) were found to be characteristic for each scavenger. The k value determined the degree in which the scavenging of •OH radicals participated in the protection of living cells. The protective effects of scavengers at the same scavenging efficiency were different and unique for each scavenger. No simple relation was found between the efficiency of scavenger k and the rate constant kOH of the reactions between scavengers and •OH radicals. Our results suggest that the studied scavengers effectively protected yeast and bacteria against ionizing radiation. Although the scavenging of •OH radicals seems to be important for protection of living cells, it is clearly not the only process on which the protection is based.

  13. The single-particle mixing state and cloud scavenging of black carbon: a case study at a high-altitude mountain site in southern China

    Science.gov (United States)

    Zhang, Guohua; Lin, Qinhao; Peng, Long; Bi, Xinhui; Chen, Duohong; Li, Mei; Li, Lei; Brechtel, Fred J.; Chen, Jianxin; Yan, Weijun; Wang, Xinming; Peng, Ping'an; Sheng, Guoying; Zhou, Zhen

    2017-12-01

    In the present study, a ground-based counterflow virtual impactor (GCVI) was used to sample cloud droplet residual (cloud RES) particles, while a parallel PM2.5 inlet was used to sample cloud-free or cloud interstitial (cloud INT) particles. The mixing state of black carbon (BC)-containing particles and the mass concentrations of BC in the cloud-free, RES and INT particles were investigated using a single-particle aerosol mass spectrometer (SPAMS) and two aethalometers, respectively, at a mountain site (1690 m a. s. l. ) in southern China. The measured BC-containing particles were extensively internally mixed with sulfate and were scavenged into cloud droplets (with number fractions of 0.05-0.45) to a similar (or slightly lower) extent as all the measured particles (0.07-0.6) over the measured size range of 0.1-1.6 µm. The results indicate the preferential activation of larger particles and/or that the production of secondary compositions shifts the BC-containing particles towards larger sizes. BC-containing particles with an abundance of both sulfate and organics were scavenged less than those with sulfate but limited organics, implying the importance of the mixing state on the incorporation of BC-containing particles into cloud droplets. The mass scavenging efficiency of BC with an average of 33 % was similar for different cloud events independent of the air mass. This is the first time that both the mixing state and cloud scavenging of BC in China have been reported. Our results would improve the knowledge on the concentration, mixing state, and cloud scavenging of BC in the free troposphere.

  14. Polyethyleneimine-Functionalized Polyamide Imide (Torlon) Hollow-Fiber Sorbents for Post-Combustion CO 2 Capture

    KAUST Repository

    Li, Fuyue Stephanie

    2013-05-24

    Carbon dioxide emitted from existing coal-fired power plants is a major environmental concern due to possible links to global climate change. In this study, we expand upon previous work focused on aminosilane-functionalized polymeric hollow-fiber sorbents by introducing a new class of polyethyleneimine (PEI)-functionalized polymeric hollow-fiber sorbents for post-combustion carbon dioxide capture. Different molecular weight PEIs (Mn≈600, 1800, 10 000, and 60 000) were studied as functional groups on polyamide imide (PAI, Torlon) hollow fibers. This imide ring-opening modification introduces two amide functional groups and was confirmed by FTIR attenuated total reflectance spectroscopy. The carbon dioxide equilibrium sorption capacities of PEI-functionalized Torlon materials were characterized by using both pressure decay and gravimetric sorption methods. For equivalent PEI concentrations, PAI functionalized with lower molecular weight PEI exhibited higher carbon dioxide capacities. The effect of water in the ring-opening reaction was also studied. Up to a critical value, water in the reaction mixture enhanced the degree of functionalization of PEI to Torlon and resulted in higher carbon dioxide uptake within the functionalized material. Above the critical value, roughly 15 % w/w water, the fiber morphology was lost and the fiber was soluble in the solvent. PEI-functionalized (Mn≈600) PAI under optimal reaction conditions was observed to have the highest CO2 uptake: 4.9 g CO2 per 100 g of polymer (1.1 mmol g-1) at 0.1 bar and 35°C with dry 10 % CO2/90 % N2 feed for thermogravimetric analysis. By using water-saturated feeds (10 % CO2/90 % N2 dry basis), CO2 sorption was observed to increase to 6.0 g CO2 per 100 g of sorbent (1.4 mmol g-1). This material also demonstrated stability in cyclic adsorption-desorption operations, even under wet conditions at which some highly effective sorbents tend to lose performance. Thus, PEI-functionalized PAI fibers can be

  15. How Predictability of Feeding Patches Affects Home Range and Foraging Habitat Selection in Avian Social Scavengers?

    NARCIS (Netherlands)

    Monsarrat, S.; Benhamou, S.; Sarrazin, F.; Bessa-Gomes, C.; Bouten, W.; Duriez, O.

    2013-01-01

    Feeding stations are commonly used to sustain conservation programs of scavengers but their impact on behaviour is still debated. They increase the temporal and spatial predictability of food resources while scavengers have supposedly evolved to search for unpredictable resources. In the Grands

  16. The French Paradox: Determining the Superoxide-Scavenging Capacity of Red Wine and Other Beverages

    Science.gov (United States)

    Logan, Barry A.; Hammond, Matthew P.; Stormo, Benjamin M.

    2008-01-01

    Plant-derived phenolic compounds such as those found in red wine, tea, and certain fruit juices may protect against cardiovascular disease by detoxifying (scavenging) superoxide and other unstable reactive oxygen species. We present a laboratory exercise that can be used to assess the superoxide-scavenging capacity of beverages. Among the…

  17. Predatory blue crabs induce stronger nonconsumptive effects in eastern oysters Crassostrea virginica than scavenging blue crabs

    Directory of Open Access Journals (Sweden)

    Avery E. Scherer

    2017-02-01

    Full Text Available By influencing critical prey traits such as foraging or habitat selection, predators can affect entire ecosystems, but the nature of cues that trigger prey reactions to predators are not well understood. Predators may scavenge to supplement their energetic needs and scavenging frequency may vary among individuals within a species due to preferences and prey availability. Yet prey reactions to consumers that are primarily scavengers versus those that are active foragers have not been investigated, even though variation in prey reactions to scavengers or predators might influence cascading nonconsumptive effects in food webs. Oysters Crassostrea virginica react to crab predators by growing stronger shells. We exposed oysters to exudates from crabs fed live oysters or fed aged oyster tissue to simulate scavenging, and to controls without crab cues. Oysters grew stronger shells when exposed to either crab exudate, but their shells were significantly stronger when crabs were fed live oysters. The stronger response to predators than scavengers could be due to inherent differences in diet cues representative of reduced risk in the presence of scavengers or to degradation of conspecific alarm cues in aged treatments, which may mask risk from potential predators subsisting by scavenging.

  18. Identification of Radical Scavenging Compounds in Rhaponticum carthamoides by Means of LC-DAD-SPE-NMR

    NARCIS (Netherlands)

    Miliauskas, G.; Beek, van T.A.; Waard, de P.; Venskutonis, R.P.; Sudhölter, E.J.R.

    2005-01-01

    A hyphenated LC-DAD-SPE-NMR setup in combination with on-line radical scavenging detection has been applied for the identification of radical scavenging compounds in extracts of Rhaponticum carthamoides. After NMR measurements, the pure compounds were infused into a mass spectrometer. The technique

  19. Isolation and Structure Elucidation of Radical Scavengers from Thymus vulgaris Leaves

    NARCIS (Netherlands)

    Dapkevicius, A.; Beek, van T.A.; Lelyveld, G.P.; Veldhuizen, van A.; Groot, de Æ.; Linssen, J.P.H.; Venskutonis, R.

    2002-01-01

    2,2-Diphenyl-1-picrylhydrazyl radical (DPPH*) scavenging activity-guided fractionation of a leaf extract of Thymus vulgaris led to the isolation of the radical scavengers rosmarinic acid 1, eriodictyol, taxifolin, luteolin 7-glucuronide, p-cymene 2,3-diol, p-cymene 2,3-diol 6-6'-dimer, carvacrol,

  20. Apoptotic and free radical scavenging properties of the methanolic extract of Gentianella alborosea.

    Science.gov (United States)

    Acero, Nuria; Llinares, Francisco; Galán de Mera, Antonio; Oltra, Beatriz; Muñoz-Mingarro, Dolores

    2006-09-01

    Gentianella alborosea ("Hercampure") is a Peruvian species used in folk medicine for the treatment of a variety of health disorders. We tested the free radical scavenging (DPPH) and induction of apoptosis on a human uterus tumor cell line (HeLa) by its methanolic extract. The results showed a noticeable radical scavenging activity and a dose-dependent apoptotic effect.