WorldWideScience

Sample records for satellite dish equipment

  1. Mobile Satellite Reception with a Virtual Satellite Dish based on a Reconfigurable Multi-Processor Architecture

    NARCIS (Netherlands)

    Burgwal, van de M.D.; Rovers, K.C.; Blom, K.C.H.; Kokkeler, A.B.J.; Smit, G.J.M.

    2011-01-01

    Traditionally, mechanically steered dishes or analog phased array beamforming systems have been used for radio frequency receivers, where strong directivity and high performance were much more important than low-cost requirements. Real-time controlled digital phased array beamforming could not be re

  2. MODELLING OF AN INEXPENSIVE 9M SATELLITE DISH FROM 3D POINT CLOUDS CAPTURED BY TERRESTRIAL LASER SCANNERS

    Directory of Open Access Journals (Sweden)

    D. Belton

    2012-09-01

    Full Text Available This paper presents the use of Terrestrial laser scanners (TLS to model the surface of satellite dish. In this case, the dish was an inexpensive 9m parabolic satellite dish with a mesh surface, and was to be utilised in radio astronomy. The aim of the modelling process was to determine the deviation of the surface away from its true parabolic shape, in order to estimate the surface efficiency with respect to its principal receiving frequency. The main mathematical problems were the optimal and unbiased estimation the orientation of the dish and the fitting of a parabola to the local orientation or coordinate system, which were done by both orthogonal and algebraic minimization using the least-squares method. Due to the mesh structure of the dish, a classification method was also applied to filter out erroneous points being influenced by the supporting structure behind the dish. Finally, a comparison is performed between the ideal parabolic shape, and the data collected from three different temporal intervals.

  3. New Equipment Training Center-Satellite Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The ARDEC Satellite Facility is a 24-hour on-site military satellite transmission and downlink capability to Southwest Asia and all other military OCONUS and CONUS...

  4. Communication Satellite Payload Special Check out Equipment (SCOE) for Satellite Testing

    Science.gov (United States)

    Subhani, Noman

    2016-07-01

    This paper presents Payload Special Check out Equipment (SCOE) for the test and measurement of communication satellite Payload at subsystem and system level. The main emphasis of this paper is to demonstrate the principle test equipment, instruments and the payload test matrix for an automatic test control. Electrical Ground Support Equipment (EGSE)/ Special Check out Equipment (SCOE) requirements, functions and architecture for C-band and Ku-band payloads are presented in details along with their interface with satellite during different phases of satellite testing. It provides test setup, in a single rack cabinet that can easily be moved from payload assembly and integration environment to thermal vacuum chamber all the way to launch site (for pre-launch test and verification).

  5. Fish Dishes.

    Science.gov (United States)

    Derby, Marie

    2003-01-01

    Describes an art project that was inspired by Greek pottery, specifically dishes shaped as fish. Explains that fourth-grade students drew a fish shape that was later used to create their clay version of the fish. Discusses how the students examined the pottery to make decisions about color and design. (CMK)

  6. Rigid collapsible dish structure

    Science.gov (United States)

    Palmer, William B. (Inventor); Giebler, Martin M. (Inventor)

    1982-01-01

    A collapsible dish structure composed of a plurality of rows of rigid radial petal assemblies concentric with the axis of the dish. The petal assemblies consist of a center petal and two side petals, the center petal hinged on an axis tangent to a circle concentric with the axis of the dish and the side petals hinged to the center petal at their mating edge. The center petal is foldable inwardly and the side petals rotate about their hinges such that the collapsed dish structure occupies a much smaller volume than the deployed dish. Means of controlling the shape of the dish to compensate for differential expansion of the deployed dish are also provided.

  7. Parabolic Dish Stirling Module

    Science.gov (United States)

    Washom, B.

    1984-01-01

    The design, manufacture, and assembly of a commercially designed parabolic dish Stirling 25 kWe module is examined. The cost, expected performance, design uniquenesses, and future commercial potential of this module, which is regarded as the most technically advanced in the parabolic dish industry is discussed.

  8. Shenandoah parabolic dish solar collector

    Energy Technology Data Exchange (ETDEWEB)

    Kinoshita, G.S.

    1985-01-01

    The objectives of the Shenandoah, Georgia, Solar Total Energy System are to design, construct, test, and operate a solar energy system to obtain experience with large-scale hardware systems for future applications. This report describes the initial design and testing activities conducted to select and develop a collector that would serve the need of such a solar total energy system. The parabolic dish was selected as the collector most likely to maximize energy collection as required by this specific site. The fabrication, testing, and installation of the parabolic dish collector incorporating improvements identified during the development testing phase are described.

  9. Shenandoah parabolic dish solar collector

    Energy Technology Data Exchange (ETDEWEB)

    Kinoshita, G.S.

    1985-01-01

    The objectives of the Shenandoah, Georgia, Solar Total Energy System are to design, construct, test, and operate a solar energy system to obtain experience with large-scale hardware systems for future applications. This report describes the initial design and testing activities conducted to select and develop a collector that would serve the need of such a solar total energy system. The parabolic dish was selected as the collector most likely to maximize energy collection as required by this specific site. The fabrication, testing, and installation of the parabolic dish collector incorporating improvements identified during the development testing phase are described.

  10. Nutational Stability of a Satellite Equipped with an Active Magnetic Momentum Wheel

    OpenAIRE

    Inoue, Masao; Tsuchiya, Kazuo; Nakajima, Atsushi; MURAKAMI, Chikara

    1988-01-01

    This paper deals with an influence of the magnetically suspended rotor on the satellite motion; although cross-feedbacks in the magnetic bearing provide stability margin to the rotor gyroscopic motion, they may destabilize the satellite nutation. Stability analyses about the dynamical interaction between the satellite and the magnetically suspended rotor whose controller used three types of (proportional, integral and derivative) cross-feedbacks were performed. The results indicated that they...

  11. Effect of nanofluid on thermal performance of heat pipe with two evaporators; application to satellite equipment cooling

    Science.gov (United States)

    Mashaei, P. R.; Shahryari, M.

    2015-06-01

    A study on the behavior of nanofluid in a cylindrical heat pipe with two heat sources is performed to analyze the nanofluid application in heat-dissipating satellite equipment cooling. Pure water, Al2O3-water and TiO2-water nanofluids are used as working fluids. An analytical modeling is presented to predict the wall temperature profile for the heat pipe assuming saturated vapor and conduction heat transfer for porous media and wall, respectively. The effects of particle concentration levels (φ=0 (distilled water), 2, 4, and 8%), particle diameters (dp=10, 20, and 40 nm) on the local wall temperature, heat transfer coefficient, thermal resistance, and the size of the heat pipe are investigated. It is observed that the better wall temperature uniformity can be achieved using nanofluid which results in lower temperature difference between evaporators and condenser sections. Results reveal that applying nanoparticle with smaller size and higher concentration level increases heat transfer coefficient remarkably by reducing thermal resistance of saturated porous media. It is also found that the presence of nanoparticles in water can lead to a reduction in weight of heat pipe, and thus satellite, under nearly identical condition. The findings of this paper prove the potential of nanofluid in satellite equipment cooling application.

  12. Dish Stirling solar receiver program

    Science.gov (United States)

    Haglund, R. A.

    1980-01-01

    A technology demonstration of a Dish Stirling solar thermal electric system can be accomplished earlier and at a much lower cost than previous planning had indicated by employing technical solutions that allow already existing hardware, with minimum modifications, to be integrated into a total system with a minimum of development. The DSSR operates with a modified United Stirling p-40 engine/alternator and the JPL Test Bed Concentrator as a completely integrated solar thermal electric system having a design output of 25 kWe. The system is augmented by fossil fuel combustion which ensures a continuous electrical output under all environmental conditions. Technical and economic studies by government and industry in the United States and abroad identify the Dish Stirling solar electric system as the most appropriate, efficient and economical method for conversion of solar energy to electricity in applications when the electrical demand is 10 MWe and less.

  13. Hangzhou People and Bamboo Shoots Dish

    Institute of Scientific and Technical Information of China (English)

    LINDA; LEE

    1995-01-01

    SOON we’ll celebrate the new year. According to Hangzhou tradition, every family will cook a hot dish for this feast which will include shredded winter bamboo shoots, hotbed chives, shredded meat and smoked bean curd. In addition, some families will also cook a dish of "braised

  14. Optimization of dish solar collectors

    Science.gov (United States)

    Jaffe, L. D.

    1983-01-01

    Methods for optimizing parabolic dish solar collectors and the consequent effects of various optical, thermal, mechanical, and cost variables are examined. The most important performance optimization is adjusting the receiver aperture to maximize collector efficiency. Other parameters that can be adjusted to optimize efficiency include focal length, and, if a heat engine is used, the receiver temperature. The efficiency maxima associated with focal length and receiver temperature are relatively broad; it may, accordingly, be desirable to design somewhat away from the maxima. Performance optimization is sensitive to the slope and specularity errors of the concentrator. Other optical and thermal variables affecting optimization are the reflectance and blocking factor of the concentrator, the absorptance and losses of the receiver, and, if a heat engine is used, the shape of the engine efficiency versus temperature curve. Performance may sometimes be improved by use of an additional optical element (a secondary concentrator) or a receiver window if the errors of the primary concentrator are large or the receiver temperature is high. Previously announced in STAR as N83-19224

  15. Parabolic dish collectors - A solar option

    Science.gov (United States)

    Truscello, V. C.

    1981-01-01

    A description is given of several parabolic-dish high temperature solar thermal systems currently undergoing performance trials. A single parabolic dish has the potential for generating 20 to 30 kW of electricity with fluid temperatures from 300 to 1650 C. Each dish is a complete power-producing unit, and may function either independently or as part of a group of linked modules. The two dish designs under consideration are of 11 and 12 meter diameters, yielding receiver operating temperatures of 925 and 815 C, respectively. The receiver designs described include (1) an organic working fluid (toluene) Rankine cycle engine; (2) a Brayton open cycle unit incorporating a hybrid combustion chamber and nozzle and a shaft-coupled permanent magnet alternator; and (3) a modified Stirling cycle device originally designed for automotive use. Also considered are thermal buffer energy storage and thermochemical transport and storage.

  16. The Translation of Chinese Dish Names

    Institute of Scientific and Technical Information of China (English)

    龚佳文

    2015-01-01

    The traditional food of a nation reflects its historical and cultural characteristics This thesis begins with an introduction to the translation situation of Chinese dish names and its existing problem nowadays, and proceeds to the translation principles and tactics for English translation of the names of Chinese dishes, based on Eugene A. Nida’ s Functional Equivalence, with an aim to improve translation efficiency and promote cross-cultural communication, and promoting Chinese food culture throughout the globe.

  17. A review of test results on parabolic dish solar thermal power modules with dish-mounted Rankine engines and for production of process steam

    Science.gov (United States)

    Jaffe, Leonard D.

    1988-01-01

    This paper presents results of development testing of various solar thermal parabolic dish modules and assemblies. Most of the tests were at modules and assemblies that used a dish-mounted, organic Rankine cycle turbine for production of electric power. Some tests were also run on equipment for production of process steam or for production of electricity using dish-mounted reciprocating steam engines. These tests indicate that early modules achieve efficiencies of about 18 percent in converting sunlight to electricity (excluding the inverter but including parasitics). A number of malfunctions occurred. The performance measurements, as well as the malfunctions and other operating experience, provided information that should be of value in developing systems with improved performance and reduced maintenance.

  18. THE MICROGARDENING COOKBOOK, DIRECTIONS FOR PREPARING DISHES AND TUBES OF STERILE NUTRIENT AGAR.

    Science.gov (United States)

    CHANDLER, MARION N.

    THIS BOOKLET WAS PREPARED FOR TEACHER USE IN ASSOCIATION WITH THE ELEMENTARY SCIENCE STUDY UNIT "MICROGARDENING." IT CONTAINS DIRECTIONS FOR PREPARING CULTURE DISHES AND TUBES OF NUTRIENT STERILE AGAR FOR FUNGAL AND/OR BACTERIAL GROWTH. IT INCLUDES (1) LISTS OF NEEDED SUPPLIES AND EQUIPMENT, (2) DIRECTIONS FOR THE PREPARATION AND…

  19. THE MICROGARDENING COOKBOOK, DIRECTIONS FOR PREPARING DISHES AND TUBES OF STERILE NUTRIENT AGAR.

    Science.gov (United States)

    CHANDLER, MARION N.

    THIS BOOKLET WAS PREPARED FOR TEACHER USE IN ASSOCIATION WITH THE ELEMENTARY SCIENCE STUDY UNIT "MICROGARDENING." IT CONTAINS DIRECTIONS FOR PREPARING CULTURE DISHES AND TUBES OF NUTRIENT STERILE AGAR FOR FUNGAL AND/OR BACTERIAL GROWTH. IT INCLUDES (1) LISTS OF NEEDED SUPPLIES AND EQUIPMENT, (2) DIRECTIONS FOR THE PREPARATION AND…

  20. Dish-mounted latent heat buffer storage

    Science.gov (United States)

    Manvi, R.

    1981-01-01

    Dish-mounted latent heat storage subsystems for Rankine, Brayton, and Stirling engines operating at 427 C, 816 C, and 816 C respectively are discussed. Storage requirements definition, conceptual design, media stability and compatibility tests, and thermal performance analyses are considered.

  1. Proceedings: Fourth Parabolic Dish Solar Thermal Power Program Review

    Science.gov (United States)

    1983-01-01

    The results of activities within the parabolic dish technology and applications development program are presented. Stirling, organic Rankine and Brayton module technologies, associated hardware and test results to date; concentrator development and progress; economic analyses; and international dish development activities are covered. Two panel discussions, concerning industry issues affecting solar thermal dish development and dish technology from a utility/user perspective, are also included.

  2. The Existing Problems in the Translation of Chinese Dish Names

    Institute of Scientific and Technical Information of China (English)

    易高燕

    2009-01-01

    China has a long rich history of dietary culture, and with the increasing communication with other countries and cultures, it is of great significance to translate the Chinese dish names and food with accuracy and efficiency. In this easy, the writer discusses some existing problems in the translation of Chinese dish names, and put forward several useful methods in translating Chinese dish names.

  3. A compendium of solar dish/Stirling technology

    Energy Technology Data Exchange (ETDEWEB)

    Stine, W.B. [California State Polytechnic Univ., Pomona, CA (United States). Dept. of Mechanical Engineering; Diver, R.B. [Sandia National Labs., Albuquerque, NM (United States)

    1994-01-01

    This report surveys the emerging dish/Stirling technology. It documents -- using consistent terminology the design characteristics of dish concentrators, receivers, and Stirling engines applicable to solar electric power generation. Development status and operating experience for each system and an overview of dish/Stirling technology are also presented. This report enables comparisons of concentrator, receiver, and engine technologies. Specifications and performance data are presented on systems and on components that are in use or that could be used in dish/Stirling systems. This report is organized into two parts: The first part (Chapters 1 through 4) provides an overview of dish/Stirling technology -- the dish/ Stirling components (concentrator, receiver, and engine/alternator), current technology, basic theory, and technology development. The second part (Chapters 5 through 7) provides a detailed survey of the existing dish/Stirling concentrators, receivers, and engine/alternators.

  4. Satellite-based estimates of light-use efficiency in a subtropical mangrove forest equipped with CO2 eddy covariance

    Directory of Open Access Journals (Sweden)

    D. O. Fuller

    2012-11-01

    Full Text Available Despite the importance of mangrove ecosystems in the global carbon budget, the relationships between environmental drivers and carbon dynamics in these forests remain poorly understood. This limited understanding is partly a result of the challenges associated with in situ flux studies. Tower-based carbon dioxide eddy covariance (EC systems are installed in only a few mangrove forests worldwide and the longest EC record from the Florida Everglades contains less than 9 yr of observations. A primary goal of the present study was to develop a methodology to estimate canopy-scale photosynthetic light use efficiency in this forest. These tower-based observations represent a basis for associating CO2 fluxes with canopy light use properties, and thus provide the means for utilizing satellite-based reflectance data for larger-scale investigations. We present a model for mangrove canopy light use efficiency utilizing the enhanced green vegetation index (EVI derived from the Moderate Resolution Imaging Spectroradiometer (MODIS that is capable of predicting changes in mangrove forest CO2 fluxes caused by a hurricane disturbance and changes in regional environmental conditions, including temperature and salinity. Model parameters are solved for in a Bayesian framework. The model structure requires estimates of ecosystem respiration (RE and we present the first-ever tower-based estimates of mangrove forest RE derived from night-time CO2 fluxes. Our investigation is also the first to show the effects of salinity on mangrove forest CO2 uptake, which declines 5% per each 10 parts per thousand (ppt increases in salinity. Light use efficiency in this forest declines with increasing daily photosynthetic active radiation, which is an important departure from the assumption of constant light use efficiency typically applied in satellite-driven models. The model developed here provides a framework for estimating CO2 uptake by these forests from reflectance data and

  5. An Automatic High Efficient Method for Dish Concentrator Alignment

    OpenAIRE

    Yong Wang; Song Li; Jinshan Xu; Yijiang Wang; Xu Cheng; Changgui Gu; Shengyong Chen; Bin Wan

    2014-01-01

    Alignment of dish concentrator is a key factor to the performance of solar energy system. We propose a new method for the alignment of faceted solar dish concentrator. The isosceles triangle configuration of facet’s footholds determines a fixed relation between light spot displacements and foothold movements, which allows an automatic determination of the amount of adjustments. Tests on a 25 kW Stirling Energy System dish concentrator verify the feasibility, accuracy, and efficiency of our...

  6. A review of test results on solar thermal power modules with dish-mounted Stirling and Brayton cycle engines

    Science.gov (United States)

    Jaffe, Leonard D.

    1988-01-01

    This paper presents results of development tests of various solar thermal parabolic dish modules and assemblies that used dish-mounted Brayton or Stirling cycle engines for production of electric power. These tests indicate that early modules achieve net efficiencies up to 29 percent in converting sunlight to electricity, as delivered to the grid. Various equipment deficiencies were observed and a number of malfunctions occurred. The performance measurements, as well as the malfunctions and other test experience, provided information that should be of value in developing systems with improved performance and reduced maintenance.

  7. Proceedings of the Fifth Parabolic Dish Solar Thermal Power Program

    Science.gov (United States)

    Lucas, J. W. (Editor)

    1984-01-01

    The proceedings of the Fifth Parabolic Dish Solar Thermal Power Program Annual Review are presented. The results of activities within the Parabolic Dish Technology and Module/Systems Development element of the Department of Energy's Solar Thermal Energy Systems Program were emphasized. Among the topics discussed were: overall Project and Program aspects, Stirling and Brayton module development, concentrator and engine/receiver development along with associated hardware and test results; distributed systems operating experience; international parabolic dish development activities; and non-DOE-sponsored domestic dish activities. Solar electric generation was also addressed.

  8. Analysis of satellite broadcasting systems for digital television

    Science.gov (United States)

    de Gaudenzi, Riccardo; Elia, Carlo; Viola, Roberto

    1993-01-01

    This paper introduces the new concept of digital direct satellite broadcasting (D-DBS), which allows unprecedented flexibility by providing a large number of audio-visual services. The concept elaborated on in this paper assumes an information rate of about 40 Mb/s, which is compatible with practically all present-day transponders. After discussion of the general system concept, the optimization procedure is introduced and results of the transmission system optimization are presented. Channel distortion and uplink/downlink interference effects are taken into account by means of a time domain system computer simulation approach. It is shown, by means of link budget analysis, how a medium power direct-to-home TV satellite can provide multimedia services to users equipped with small (60 cm) dish antennas.

  9. Dish/Stirling for Department of Defense applications final report

    Energy Technology Data Exchange (ETDEWEB)

    Diver, R.B.; Menicucci, D.F. [Sandia National Labs., Albuquerque, NM (United States). Energy and Environment Div.

    1997-03-01

    This report describes a Strategic Environmental Research and Development Program (SERDP) project to field a dish/Stirling system at a southwestern US military facility. This project entitled ``Dish/Stirling for DoD Applications`` was started in August 1993 and was completed in September 1996. The project`s objective was to assist military facilities to field and evaluate emerging environmentally sound and potentially economical dish/Stirling technology. Dish/Stirling technology has the potential to produce electricity at competitive costs while at the same time providing a secure and environmentally benign source of power. In accordance with the SERDP charter, this project leveraged a US Department of Energy (DOE) cost-shared project between Sandia National Laboratories and Cummins Power Generation, Inc. (CPG). CPG is a wholly owned subsidiary of Cummins Engine Company, a leading manufacturer of diesel engines. To accomplish this objective, the project called for the installation of a dish/Stirling system at a military facility to establish first-hand experience in the operation of a dish/Stirling system. To scope the potential DoD market for dish/Stirling technology and to identify the site for the demonstration, a survey of southwestern US military facilities was also conducted. This report describes the project history, the Cummins dish/Stirling system, results from the military market survey, and the field test results.

  10. An Automatic High Efficient Method for Dish Concentrator Alignment

    Directory of Open Access Journals (Sweden)

    Yong Wang

    2014-01-01

    for the alignment of faceted solar dish concentrator. The isosceles triangle configuration of facet’s footholds determines a fixed relation between light spot displacements and foothold movements, which allows an automatic determination of the amount of adjustments. Tests on a 25 kW Stirling Energy System dish concentrator verify the feasibility, accuracy, and efficiency of our method.

  11. El ídish en el teatro argentino

    Directory of Open Access Journals (Sweden)

    David William Foster

    2009-10-01

    Full Text Available Analise de tres instancias de teatro en ídish en Buenos Aires. La primera, un teatro hablado en ídish que surge de los contextos de la inmigración, que tiene que ver con la vida milenaria de los judíos, de los recuerdos del shetl, de los pogroms. La segunda es el teatro de las vivencias en territorio argentino, en el ámbito de la narrativa, ya en ídish, ya en castellano. La tercera ejemplifica el comienzo de la desaparición del ídish, con espectadores de otras ascendencias inmigratorias, que no van a entender el ídish, con la creciente debilidad del ídish en la colectividad, o por efecto de la asimilación o por el trágico hecho de que el ídish había emprendido la enorme decadencia impuestas por el nazismo, que desembocará eventualmente en la muerte del idioma que, en la Argentina y en muchos otros lugares, más se identificaba con los judíos.

  12. Dish stirling solar receiver combustor test program

    Science.gov (United States)

    Bankston, C. P.; Back, L. H.

    1981-01-01

    The operational and energy transfer characteristics of the Dish Stirling Solar Receiver (DSSR) combustor/heat exchanger system was evaluated. The DSSR is designed to operate with fossil fuel augmentation utilizing a swirl combustor and cross flow heat exchanger consisting of a single row of 4 closely spaced tubes that are curved into a conical shape. The performance of the combustor/heat exchanger system without a Stirling engine was studied over a range of operating conditions and output levels using water as the working fluid. Results show that the combustor may be started under cold conditions, controlled safety, and operated at a constant air/fuel ratio (10 percent excess air) over the required range of firing rates. Furthermore, nondimensional heat transfer coefficients based on total heat transfer are plotted versus Reynolds number and compared with literature data taken for single rows of closely spaced tubes perpendicular to cross flow. The data show enhanced heat transfer for the present geometry and test conditions. Analysis of the results shows that the present system meets specified thermal requirements, thus verifying the feasibility of the DSSR combustor design for final prototype fabrication.

  13. Prototype dish testing and analysis at Sandia National Laboratories

    Science.gov (United States)

    Grossman, J. W.; Houser, R. M.; Erdman, W. W.

    1991-12-01

    During the past year, Sandia National Laboratories performed on-sun testing of several dish concentrator concepts. These tests were undertaken at the National Solar Thermal Test Facility (NSTTF). Two of the tests were performed in support of the DOE Concentrator Receiver Development Program. The first was on-sun testing of the single-element stretched-membrane dish; this 7-meter diameter dish uses a single preformed metal membrane with an aluminized polyester optical surface and shows potential for future dish-Stirling systems. The next involved two prototype facets from the Faceted Stretched-Membrane Dish Program. These facets, representing competitive design concepts, are closest to commercialization. Five 1-meter triangular facets were tested on-sun as part of the development program for a solar dynamic system on Space Station Freedom. While unique in character, all the tests utilized the Beam Characterization System (BCS) as the main measurement tool and all were analyzed using the Sandia-developed CIRCE2 computer code. The BCS is used to capture and digitize an image of the reflected concentrator beam that is incident on a target surface. The CIRCE2 program provides a computational tool, which when given the geometry of the concentrator and target as well as other design parameters will predict the flux distribution of the reflected beam. One of these parameters, slope error, is the variable that has a major effect in determining the quality of the reflected beam. The methodology used to combine these two tools to predict uniform slope errors for the dishes is discussed in this document. As the Concentrator Development Programs continue, Sandia will test and evaluate two prototype dish systems. The first, the faceted stretched-membrane dish, is expected to be tested in 1992, followed by the full-scale single-element stretched-membrane dish in 1993. These tests will use the tools and methodology discussed in this document.

  14. Performance of the Southern California Edison Company Stirling dish

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, C.W. [Southern California Edison Co., Rosemead, CA (United States); Stone, K.W. [Mako Enterprises, Huntington Beach, CA (United States)

    1993-10-01

    McDonnell Douglas Astronautics Company (MDAC) and United Stirling AB of Sweden (USAB) formed a joint venture in 1982 to develop and produce a Stirling dish solar generating system. In this report, the six year development and testing program continued by the Southern California Edison Company (SCE) is described. Each Stirling dish module consists of a sun tracking dish concentrator developed by the MDAC and a Stirling engine driven power conversion unit (PCU) developed by USAB. The Stirling dish system demonstrated twice the peak and daily solar-to-electric conversion efficiency of any other system then under development. This system continues to set the performance standard for solar to electric systems being developed in the early 1990`s. Test data are presented and used to estimate the performance of a commercial system.

  15. Shanghai Dishes at the Beijing Asia Jinjiang Hotel

    Institute of Scientific and Technical Information of China (English)

    1996-01-01

    THE Beijing Asia Jinjiang Hotel in east Beijing is neither magnificent nor luxuriant, but the Shanghai cuisine served there makes it popular. The unforgettable dishes are the weapon that this hotel uses to compete with bigger hotels in the neighborhood.

  16. The JPL parabolic dish project. [solar collectors technology development

    Science.gov (United States)

    Truscello, V. C.; Williams, A. N.

    1980-01-01

    The parabolic dish solar collector is a highly versatile concentrating collector system that can produce heat for many thermal processes and electricity by coupling the collector to a suitable heat engine. This paper discusses a project for the development of these collector systems and summarizes contracts with industry for developing the dish subsystems which include concentrator, receiver, and heat engine. An early market for dishes is the dispersed small community market which depends heavily on oil to operate diesel or steam turbine plants in order to generate electricity. The present contracts with industry for conducting engineering experiments using the developed dish hardware to demonstrate the technology in these early opportunity markets is also discussed.

  17. Modelling of Steam Generating Paraboloidal dish Solar Thermal Power System

    Energy Technology Data Exchange (ETDEWEB)

    Siangsukone, P.; Lovegrove, K.

    2006-07-01

    The Australian National University (ANU) has a 400m2 Paraboloidal dish solar concentrator system, informally named the Big Dish that produces superheated steam via a receiver mounted monotube boiler connected to 50kWe steam engine for electricity generation. This paper describes an investigation of the system and its components modelled using the TRNYSYS transient system simulation package. The system was modelled in the context of performance assessment for multiple dishes, central generation Rankine cycle power plants. Five new custom components; paraboloidal dish collector, steam cavity receiver, steam line or feedwater line, steam engine, and pressure drop calculator, were developed for the TRNSYS deck file constructed for this study. Validation tests were performed by comparing with the latest experimental results measured with a 1-minute time step and good agreement, with errors less than 10%, has been found. (Author)

  18. Three-month performance evaluation of the Nanometrics, Inc., Libra Satellite Seismograph System in the northern California Seismic Network

    Science.gov (United States)

    Oppenheimer, David H.

    2000-01-01

    In 1999 the Northern California Seismic Network (NCSN) purchased a Libra satellite seismograph system from Nanometrics, Inc to assess whether this technology was a cost-effective and robust replacement for their analog microwave system. The system was purchased subject to it meeting the requirements, criteria and tests described in Appendix A. In early 2000, Nanometrics began delivery of various components of the system, such as the hub and remote satellite dish and mounting hardware, and the NCSN installed and assembled most equipment in advance of the arrival of Nanometrics engineers to facilitate the configuration of the system. The hub was installed in its permanent location, but for logistical reasons the "remote" satellite hardware was initially configured at the NCSN for testing. During the first week of April Nanometrics engineers came to Menlo Park to configure the system and train NCSN staff. The two dishes were aligned with the satellite, and the system was fully operational in 2 days with little problem. Nanometrics engineers spent the remaining 3 days providing hands-on training to NCSN staff in hardware/software operation, configuration, and maintenance. During the second week of April 2000, NCSN staff moved the entire remote system of digitizers, dish assembly, and mounting hardware to Mammoth Lakes, California. The system was reinstalled at the Mammoth Lakes water treatment plant and communications successfully reestablished with the hub via the satellite on 14 April 2000. The system has been in continuous operation since then. This report reviews the performance of the Libra system for the three-month period 20 April 2000 through 20 July 2000. The purpose of the report is to assess whether the system passed the acceptance tests described in Appendix A. We examine all data gaps reported by NCSN "gap list" software and discuss their cause.

  19. A special dish from traditional Turkish Cuisine: Stuffed lamb ribs

    Directory of Open Access Journals (Sweden)

    Emel Memis Kocaman

    2015-11-01

    Full Text Available Turkish people, who have a long historical background, have a rich culture in terms of cuisine. “Dolma” (meal made by stuffing/wrapping is one of the most important dishes of the Turkish Cuisine. Turks produced very different types of meals made by stuffing or wrapping and by combining herbals, meat and offals products. Stuffed Lamb Ribs (in Turkish; Kaburga Dolması or Sura is a special dish that is known in many regions of Turkey. Since it is a dish whose preparation is hard and requires virtuosity, it is generally cooked as a feast meal on religious holidays, and commonly cooked on the Feast of Sacrifice for Muslims. This study aims to present how “Stuffed Lamb Ribs” are prepared, which is one of the traditional dishes of Turkish Cuisine and is one stuffed dish that has started to become forgotten. In this study, the data was collected by personal interviews with source people who are over 60 years old, live in different provinces of Turkey, and traditionally cook this dish. This study ensures the promotion of a very special taste, which has begun to be forgotten and is not known widely even in Turkey, at an international level.

  20. Mechanical design of a low cost parabolic solar dish concentrator

    Directory of Open Access Journals (Sweden)

    Hamza Hijazi

    2016-03-01

    Full Text Available The objective of this research was to design a low cost parabolic solar dish concentrator with small-to moderate size for direct electricity generation. Such model can be installed in rural areas which are not connected to governmental grid. Three diameters of the dish; 5, 10 and 20 m are investigated and the focal point to dish diameter ratio is set to be 0.3 in all studied cases. Special attention is given to the selection of the appropriate dimensions of the reflecting surfaces to be cut from the available sheets in the market aiming to reduce both cutting cost and sheets cost. The dimensions of the ribs and rings which support the reflecting surface are optimized in order to minimize the entire weight of the dish while providing the minimum possible total deflection and stresses in the beams. The study applies full stress analysis of the frame of the dish using Autodesk Inventor. The study recommends to use landscape orientation for the reflective facets and increase the ribs angle and the distance between the connecting rings. The methodology presented is robust and can be extended to larger dish diameters.

  1. [Typical dishes consumed in Sonora: regionalization and nutrient contribution].

    Science.gov (United States)

    Jardines, R P; Bermúdez, M C; Wong, P; León, G

    1985-12-01

    This study deals with the development of a method to identify typical food dishes, successfully applied in the State of Sonora, Mexico. The State was divided into six regions considering the size of the territory and existence of different physical, economic and sociocultural conditions, and how they influence the consumption patterns. A list of 66 regional food dishes was prepared by interviewing housewives from different parts of Sonora who now lived in the city of Hermosillo. From this list, 47 dishes were identified as regionally consumed, and a State-wide survey was performed to determine their frequency of consumption. Based on the categories of "very frequently", "frequently" and "less frequently", a group of 15 dishes (2 per region, plus 3 dishes throughout the State) was selected. A questionnaire was used to obtain the different ways they had of preparing them. The "typical recipe" for each dish was also determined, using the mode as statistical parameter. Samples of these food dishes were prepared at the laboratory following the selected home recipes for proximal analysis and determination of their vitamin A, thiamine, riboflavin, niacin, calcium, phosphorus and iron content. The results showed that a portion of "gallina pinta" contributed more than 25% of the daily recommended intake established by the National Institute of Nutrition "Salvador Zubirán" (INNSZ) for an adult man for energy, protein, iron, niacin and 24.3% thiamine and 21.0% calcium. The "chivichangas de queso", for example, contributed 45.2% of the calcium requirement, and the "tamales de carne", 36% iron.(ABSTRACT TRUNCATED AT 250 WORDS)

  2. Fifth parabolic dish solar thermal power program annual review: proceedings

    Energy Technology Data Exchange (ETDEWEB)

    None

    1984-03-01

    The primary objective of the Review was to present the results of activities within the Parabolic Dish Technology and Module/Systems Development element of the Department of Energy's Solar Thermal Energy Systems Program. The Review consisted of nine technical sessions covering overall Project and Program aspects, Stirling and Brayton module development, concentrator and engine/receiver development, and associated hardware and test results to date; distributed systems operating experience; international dish development activities; and non-DOE-sponsored domestic dish activities. A panel discussion concerning business views of solar electric generation was held. These Proceedings contain the texts of presentations made at the Review, as submitted by their authors at the beginning of the Review; therefore, they may vary slightly from the actual presentations in the technical sessions.

  3. Technical status of the Dish/Stirling Joint Venture Program

    Science.gov (United States)

    Bean, John R.; Diver, Richard B.

    Initiated in 1991; the Dish/Stirling Joint Venture Program (DSJVP) is a 5-year, $17.2 million joint venture which is funded by Cummins Power Generation, Inc. (CPG) of Columbus, Indiana and the United States Department of Energy's (DOE) Solar Thermal and Biomass Power Division. Sandia National Laboratories administers and provides technical management for this contract on the DOE's behalf. In January, 1995; CPG advanced to Phase 3 of this three-phase contract. The objective of the DSJVP is to develop and commercialize a 7-kW. Dish/Stirling System for remote power markets by 1997. In this paper, the technical status of the major subsystems which comprise the CPG 7-kW(sub e) Dish/Stirling System is presented. These subsystems include the solar concentrator, heat pipe receiver, engine/alternator, power conditioning, and automatic controls.

  4. Experiments on the dish verification antenna china for the SKA

    Science.gov (United States)

    Chai, Xiaoming; Liu, Bin; Yu, Lei; Yu, Shenghua; Wu, Di; Liu, Lijia

    2016-12-01

    The Square Kilometre Array (SKA) is expected to become the world's most powerful radio telescope at meter and centimeter wavelength in the coming decades. The construction of SKA will be divided into two phases. The first phase (SKA1), scheduled for completion in 2023, will construct 10 % of the whole collecting area. The second phase (SKA2) will build the rest 90 % collecting area. The SKA1 consists of several types of arrays including SKA1-low and SKA1-mid. The latter is a dish array consisting of 200 medium-size antennas. The integrated dish array in SKA2 will expand to 2500 dishes, spreading 3000 kilometers across the southern part of Africa. The demanding specifications and enormous number of the SKA dish raise challenges in the dish development such as mass production with high performance at low cost, quick installation and high reliability. Dish Verification Antenna China (DVA-C) was built as one of three initial prototypes. A novel single-piece panel reflector made of carbon fiber reinforced polymer (CFRP) was adopted. In this study, an L-band receiver is installed to make DVA-C a complete system for experiments on antenna performance test and preliminary observations. The performance of DVA-C including the system noise temperature, pointing accuracy, antenna pattern, and aperture efficiency has been tested. Preliminary observations such as pulsars and HI are then conducted, which indicates that the DVA-C can not only serve as an educational instrument and key technology test bed, but also be applied for scientific work such as pulsar timing, all-sky HI survey, multi-frequency monitoring of variable sources etc.

  5. Experiments on the dish verification antenna china for the SKA

    Science.gov (United States)

    Chai, Xiaoming; Liu, Bin; Yu, Lei; Yu, Shenghua; Wu, Di; Liu, Lijia

    2016-09-01

    The Square Kilometre Array (SKA) is expected to become the world's most powerful radio telescope at meter and centimeter wavelength in the coming decades. The construction of SKA will be divided into two phases. The first phase (SKA1), scheduled for completion in 2023, will construct 10 % of the whole collecting area. The second phase (SKA2) will build the rest 90 % collecting area. The SKA1 consists of several types of arrays including SKA1-low and SKA1-mid. The latter is a dish array consisting of ~200 medium-size antennas. The integrated dish array in SKA2 will expand to 2500 dishes, spreading 3000 kilometers across the southern part of Africa. The demanding specifications and enormous number of the SKA dish raise challenges in the dish development such as mass production with high performance at low cost, quick installation and high reliability. Dish Verification Antenna China (DVA-C) was built as one of three initial prototypes. A novel single-piece panel reflector made of carbon fiber reinforced polymer (CFRP) was adopted. In this study, an L-band receiver is installed to make DVA-C a complete system for experiments on antenna performance test and preliminary observations. The performance of DVA-C including the system noise temperature, pointing accuracy, antenna pattern, and aperture efficiency has been tested. Preliminary observations such as pulsars and HI are then conducted, which indicates that the DVA-C can not only serve as an educational instrument and key technology test bed, but also be applied for scientific work such as pulsar timing, all-sky HI survey, multi-frequency monitoring of variable sources etc.

  6. The HERA Dish II: Electromagnetic Simulations and Science Implications

    CERN Document Server

    Ewall-Wice, Aaron; DeBoer, David; Hewitt, Jacqueline; Parsons, Aaron; Aguirre, James; Ali, Zaki S; Bowman, Judd; Cheng, Carina; Neben, Abraham R; Patra, Nipanjana; Thyagarajan, Nithyanandan; Venter, Mariet; Acedo, Eloy de Lera; Dillon, Joshua S; Doolittle, Roger; Egan, Dennis; Hendrick, Mike; Klima, Patricia; Kohn, Saul; Schaffner, Patrick; Shelton, John; Saliwanchik, Benjamin; Tegmark, Max; Taylor, H A; Taylor, Rusty; Wirt, Butch

    2016-01-01

    We use time-domain electromagnetic simulations to assess the spectral characteristics of the dish antenna for the Hydrogen Epoch of Reionization Array (HERA). These simulations are part of a multi-faceted campaign to determine the effectiveness of the dish's design for obtaining a detection of redshifted 21 cm emission from the epoch of reionization. Our simulations show the existence of reflections between HERA's suspended feed and its parabolic dish reflector, at certain frequencies, with an amplitude of roughly $ -35$dB at 100 ns which can lead to some loss of measurable modes and a modest reduction in sensitivity. Even in the presence of this structure, we find that the spectral response of the dish is sufficiently smooth for delay filtering, a proven foreground isolation technique, to contain foreground emission at line-of-sight wave numbers below $k_\\parallel \\lesssim 0.2h$Mpc$^{-1}$, in the region where the current PAPER experiment operates. Incorporating these results into a Fisher Matrix analysis, we...

  7. Combined Heat & Power Using the Infinia Concentrated Solar - CHP PowerDish System

    Science.gov (United States)

    2013-08-01

    installed cost as the PowerDish CHP system). The solar thermal system selected and installed will be a low or medium-temperature collector system...implementing the PowerDish CHP. ...................................... 29 Table 8. Important costs for implementing the PowerDish CHP versus PV- solar thermal ...capabilities of the Infinia PowerDish CHP technology to generate clean solar electricity as well as thermal energy for domestic hot water and space

  8. Irrigation market for solar thermal parabolic dish systems

    Science.gov (United States)

    Habib-Agahi, H.; Jones, S. C.

    1981-01-01

    The potential size of the onfarm-pumped irrigation market for solar thermal parabolic dish systems in seven high-insolation states is estimated. The study is restricted to the displacement of three specific fuels: gasoline, diesel and natural gas. The model was developed to estimate the optimal number of parabolic dish modules per farm based on the minimum cost mix of conventional and solar thermal energy required to meet irrigation needs. The study concludes that the potential market size for onfarm-pumped irrigation applications ranges from 101,000 modules when a 14 percent real discount rate is assumed to 220,000 modules when the real discount rate drops to 8 percent. Arizona, Kansas, Nebraska, New Mexico and Texas account for 98 percent of the total demand for this application, with the natural gas replacement market accounting for the largest segment (71 percent) of the total market.

  9. Dish concentrators for solar thermal energy - Status and technology development

    Science.gov (United States)

    Jaffe, L. D.

    1981-01-01

    Comparisons are presented of point-focusing, or 'dish' solar concentrator system features, development status, and performance levels demonstrated to date. In addition to the requirements of good optical efficiency and high geometric concentration ratios, the most important future consideration in solar thermal energy dish concentrator design will be the reduction of installed and lifetime costs, as well as the materials and labor costs of production. It is determined that technology development initiatives are needed in such areas as optical materials, design wind speeds and wind loads, structural configuration and materials resistance to prolonged exposure, and the maintenance of optical surfaces. The testing of complete concentrator systems, with energy-converting receivers and controls, is also necessary. Both reflector and Fresnel lens concentrator systems are considered.

  10. FPGA applications for single dish activity at Medicina radio telescopes

    Science.gov (United States)

    Bartolin, M.; Nald, G.; Mattan, A.; Maccaferr, A.; De Biagg, M.

    FPGA technologies are gaining major attention in the recent years in the field of radio astronomy. At Medicina radio telescopes, FPGAs have been used in the last ten years for a number of purposes and in this article we will take into exam the applications developed and installed for the Medicina Single Dish 32m Antenna: these range from high performance digital signal processing to instrument control developed on top of smaller FPGAs.

  11. Thermal Model of a Dish Stirling Cavity-Receiver

    OpenAIRE

    Rubén Gil; Carlos Monné; Nuria Bernal; Mariano Muñoz; Francisco Moreno

    2015-01-01

    This paper presents a thermal model for a dish Stirling cavity based on the finite differences method. This model is a theoretical tool to optimize the cavity in terms of thermal efficiency. One of the main outcomes of this work is the evaluation of radiative exchange using the radiosity method; for that purpose, the view factors of all surfaces involved have been accurately calculated. Moreover, this model enables the variation of the cavity and receiver dimensions and the materials to deter...

  12. Searching for WISPy cold dark matter with a dish antenna

    Energy Technology Data Exchange (ETDEWEB)

    Horns, Dieter [Hamburg Univ. (Germany). Inst. fuer Experimentalphysik; Jaeckel, Joerg [Heidelberg Univ. (Germany). Inst. fuer Theoretische Physik; Durham Univ. (United Kingdom). Inst. for Particle Physics Phenomenology; Lindner, Axel; Ringwald, Andreas [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Lobanov, Andrei [Max-Planck-Institut fuer Radioastronomie, Bonn (Germany); Redondo, Javier [Muenchen Univ. (Germany). Arnold Sommerfeld Center; Max-Planck-Institut fuer Physik, Muenchen (Germany)

    2012-12-15

    The cold dark matter of the Universe may be comprised of very light and very weakly interacting particles, so-called WISPs. Two prominent examples are hidden photons and axion-like particles. In this note we propose a new technique to sensitively search for this type of dark matter with dish antennas. The technique is broadband and allows to explore a whole range of masses in a single measurement.

  13. Parabolic dish reflectors for solar applications approximated by simple surfaces

    OpenAIRE

    Broman, Lars; Broman, Arne

    1996-01-01

    Two different concentrating mirrors have been constructed that resemble parabolic dish reflectors. Both mirrors are made of slightly curved strips of flat, bendable material. The strips of the most simplified mirror have only large-radius circles and straight lines as boundaries. The necessary equations for making the mirrors have been derived. Also a simple way to make a stiff, lightweight frame and support for the mirror strips has been developed. Models of the mirrors have been built and s...

  14. Searching for WISPy Cold Dark Matter with a Dish Antenna

    CERN Document Server

    Horns, Dieter; Lindner, Axel; Lobanov, Andrei; Redondo, Javier; Ringwald, Andreas

    2012-01-01

    The cold dark matter of the Universe may be comprised of very light and very weakly interacting particles, so-called WISPs. Two prominent examples are hidden photons and axion-like particles. In this note we propose a new technique to sensitively search for this type of dark matter with dish antennas. The technique is broadband and allows to explore a whole range of masses in a single measurement.

  15. Irrigation market for solar-thermal parabolic-dish systems

    Energy Technology Data Exchange (ETDEWEB)

    Habib-agahi, H.; Jones, S.C.

    1981-09-01

    The potential size of the onfarm-pumped irrigation market for solar thermal parabolic dish systems in seven high-insolation states is estimated. The study is restricted to the displacement of three specific fuels: gasoline, diesel and natural gas. A model was developed to estimate the optimal number of parabolic dish modules per farm based on the minimum cost mix of conventional and solar thermal energy required to meet irrigation needs. Results indicate that the near-term market for such systems depends not only on the type of crop and method of irrigation, but also on the optimal utilization of each added module, which in turn depends on the price of conventional fuel, real discount rate, marginal cost of the solar thermal power system, local insolation level and parabolic dish system efficiency. The study concludes that the potential market size for onfarm-pumped irrigation applications ranges from 101,000 modules when a 14% real discount rate is assumed to 220,000 modules when the real discount rate drops to 8%. Arizona, Kansas, Nebraska, New Mexico and Texas account for 98% of the total demand for this application, with the natural gas replacement market accounting for the largest segment (71%) of the total market.

  16. Fluorescence microscopy imaging of cells with a plasmonic dish integrally molded

    Science.gov (United States)

    Tawa, Keiko; Sasakawa, Chisato; Fujita, Tsuyoshi; Kiyosue, Kazuyuki; Hosokawa, Chie; Nishii, Junji; Oike, Makoto; Kakinuma, Norihiro

    2016-03-01

    A plastic dish with a wavelength-scale periodic structure at a bottom panel was integrally molded and coated with thin metal films. The integrally molded dish called plasmonic dish was applied to bioimaging under a fluorescence microscope. On the plasmonic substrate, the enhanced electric field based on a grating-coupled surface plasmon resonance (GC-SPR) can provide an enhanced fluorescence. In this study, two kinds of cells, human embryonic kidney (HEK) cells and neuronal cells, were observed in our plasmonic dish. Fluorescence images of HEK cells were above 10 times brighter than those obtained on a conventional glass-bottomed dish. Neuronal cells were successfully cultured for 10 d on the plasmonic dish integrally molded, and in fluorescence images with transmitted light, a higher contrast was obtained than in epifluorescence images. The plasmonic dish integrally molded, as well as that fabricated by the UV nanoimprint method, was also found to be useful for sensitive bioimaging.

  17. Flexible Sheet-Type Sensor for Noninvasive Measurement of Cellular Oxygen Metabolism on a Culture Dish.

    Directory of Open Access Journals (Sweden)

    Mari Kojima

    Full Text Available A novel flexible sensor was developed for the noninvasive oxygen metabolism measurement of cultivated cells and tissues. This device is composed of a transparent double-layered polymer sheet of ethylene-vinyl alcohol (EVOH and poly(dimethylsiloxane (PDMS having an array of microhole structures of 90 μm diameter and 50 μm depth on its surface. All the microhole structures were equipped with a 1-μm-thick optical chemical sensing layer of platinum porphyrin-fluoropolymer on their bottom. The three-dimensional microstructures of the sensor were fabricated by a newly developed simple and low-cost production method named self-aligned hot embossing. The device was designed to be attached slightly above the cells cultivated on a dish to form a temporarily closed microspace over the target cells during measurement. Since the change in oxygen concentration is relatively fast in the microcompartmentalized culture medium, a rapid evaluation of the oxygen consumption rate is possible by measuring the phosphorescence lifetime of the platinum porphyrin-fluoropolymer. The combined use of the device and an automated optical measurement system enabled the high-throughput sensing of cellular oxygen consumption (100 points/min. We monitored the oxygen metabolism of the human breast cancer cell line MCF7 on a Petri dish and evaluated the oxygen consumption rate to be 0.72 ± 0.12 fmol/min/cell. Furthermore, to demonstrate the utility of the developed sensing system, we demonstrated the mapping of the oxygen consumption rate of rat brain slices and succeeded in visualizing a clear difference among the layer structures of the hippocampus, i.e., the cornu ammonis (CA1 and CA3 and dentate gyrus (DG.

  18. 星载交换机中高性能队列管理器的研究与实现%Research and implementation of a high performance queue management equipment on the satellite onboard switch

    Institute of Scientific and Technical Information of China (English)

    王孟磊; 施扬; 乔庐峰; 禹明刚

    2012-01-01

    针对星载交换机中硬件处理速度和存储器容量受限的情况,设计实现了一个高性能队列管理器.采用虚拟输出排队机制改善输入缓存中存在的队头阻塞问题;使用前向地址指针pre_addr和后向地址指针nxt addr控制信元的写入和读出.通过ModelSim SE行为级时序仿真可知,其能够达到星载交换机的队列时延要求,具有较高的交换性能及稳定性.%This paper implements a high performance queue management equipment due to the limitation of hardware procession speed and memory capacity on the satellite onboard switch. It utilizes virtual output queue(VOQ) to improve the HOL problem of input buffer, and control the writing and reading of a cell by implementing the previous address pointer (pre_addr) and the next address pointer (nxt_addr). The results of ModelSim SE behavioral timing simulation show that it satisfies the need of queue delay of the satellite onboard switch, and has high performance and stability.

  19. Secondary and compound concentrators for parabolic dish solar thermal power systems

    Science.gov (United States)

    Jaffe, L. D.; Poon, P. T.

    1981-01-01

    A secondary optical element may be added to a parabolic dish solar concentrator to increase the geometric concentration ratio attainable at a given intercept factor. This secondary may be a Fresnel lens or a mirror, such as a compound elliptic concentrator or a hyperbolic trumpet. At a fixed intercept factor, higher overall geometric concentration may be obtainable with a long focal length primary and a suitable secondary matched to it. Use of a secondary to increase the geometric concentration ratio is more likely to e worthwhile if the receiver temperature is high and if errors in the primary are large. Folding the optical path with a secondary may reduce cost by locating the receiver and power conversion equipment closer to the ground and by eliminating the heavy structure needed to support this equipment at the primary focus. Promising folded-path configurations include the Ritchey-Chretien and perhaps some three element geometries. Folding the optical path may be most useful in systems that provide process heat.

  20. Secondary and compound concentrators for parabolic-dish solar-thermal power systems

    Energy Technology Data Exchange (ETDEWEB)

    Jaffe, L.D.; Poon, P.T.

    1981-04-15

    A secondary optical element may be added to a parabolic dish solar concentrator to increase the geometric concentration ratio attainable at a given intercept factor. This secondary may be a Fresnel lens or a mirror, such as a compound elliptic concentrator or a hyperbolic trumpet. At a fixed intercept factor, higher overall geometric concentration may be obtainable with a long focal length primary and a suitable secondary matched to it. Use of a secondary to increase the geometric concentration ratio is more likely to be worthwhile if the receiver temperature is high and if errors in the primary are large. Folding the optical path with a secondary may reduce cost by locating the receiver and power conversion equipment closer to the ground and by eliminating the heavy structure needed to support this equipment at the primary focus. Promising folded-path configurations include the Ritchey-Chretien and perhaps some three-element geometries. Folding the optical path may be most useful in systems that provide process heat.

  1. Dish Stirling system integration and test progress report

    Science.gov (United States)

    Haglund, R. A.

    1982-01-01

    The integration and check-out of a complete Dish Solar Stirling Thermal Power System is described. The preliminary results of the tests conducted thus far are presented. The results are very encouraging and show promise of high performance and efficiency. The outstanding performance and durability of the 4-95 Stirling engine was the highlight of this 6 month integration and test activity. Exposure to severe heat, dust, sand and wind during the summer months and heavy rains, high winds, including sand storms and freezing cold in recent months did affected the engine or the receiver in any noticable manner.

  2. Gods, Germs, and Petri Dishes: Toward a Nonsecular Medical Anthropology.

    Science.gov (United States)

    Roberts, Elizabeth F S

    2016-01-01

    This commentary calls on medical anthropology to become programmatically non-secular. Despite recent anthropological critiques of secularity, within and outside of anthropology, most contemporary medical anthropologists continue to leave deities and religiosity out of their examinations of healing practices, especially in their accounts of biomedicine. Through a critical, relational constructionist lens, which traces how all entities are both constructed and real, a non-secular medical anthropology would insist that when deities are part of medical practice, they are integral to analysis. Importantly then, within the symmetrical nature of this same constructionist lens, biomedical entities like germs and petri dishes need to be accounted for just as much as deities.

  3. Spondyloarthritis, diffuse idiopathic skeletal hyperostosis (DISH) and chondrocalcinosis.

    Science.gov (United States)

    Armas, Jácome Brugues; Couto, Ana Rita; Bettencourt, Bruno Filipe

    2009-01-01

    The authors describe the main clinical and radiological findings of common enthesopathic disorders-spondylarthritis (SpA), chondrocalcinosis/calcium pyrophosphate dehydrate crystal deposition disease (CPPD CDD) and diffuse idiopathic skeletal hyperostosis (DISH), stressing similarities and differences which may help in the differential diagnosis. They emphasize the clinical presentation of the "pseudoankylosing spondylitis" forms of CPPD CDD. They also review the most relevant genes and molecular mechanisms associated with these conditions and with another enthesopathic disorder with high prevalence in the Japanese population-ossification of the posterior longitudinal ligament (OPLL).

  4. An analysis on Translation Strategies of Chinese Dishes

    Institute of Scientific and Technical Information of China (English)

    高慧妍

    2013-01-01

    Cuisine culture occupies a pivotal position in nation’s culture especially in China. Chinese cooking has become a link between Chinese people and people from other countries and an important window for them to know Chinese culture. Hence, to translate those Chinese dish names has been put outstandingly to us, not only because this is the need to promote the comity and understanding between them and us, but also the key job to spread our tradition culture to the world. This thesis attempts to have a brief study of Chinese cuisine naming and put forward some translation methods, such as transliteration, domestication, and so on. Without neglecting some related obstacles.

  5. Telelibrary: Library Services via Satellite.

    Science.gov (United States)

    Liu, Rosa

    1979-01-01

    Investigates the provision of library services via satellite, explains briefly the operation and advantages of communication satellites, and discusses the various telecommunications equipment and services which, when coupled with satellite transmission, will enhance library activities. Demand trend projections for telecommunications services…

  6. Diffuse idiopathic skeletal hyperostosis (D.I.S.H.

    Directory of Open Access Journals (Sweden)

    F. De Leonardis

    2011-09-01

    Full Text Available Diffuse idiopathic skeletal hyperostosis (D.I.S.H. is a common disorder of unknown aetiology characterized by exuberant hyperostosis of the antero-lateral aspect of the spinal column, that sometimes leads to bone ankilosis, and by ossification of extra-spinal entheses. This condition is often associated with the metabolic derangement of type 2 diabetes. Primary hypertension, its cardiovascular aftereffects and lithiasis are also often present in these patients. D.I.S.H. has to be distinguished from osteoarthritis, althought they often coexist in the same patient. The mean difference lies in the anatomical target of the pathological process, that is represented by articular cartilage in osteoarthritis and by entheses in diffuse idiopathic skeletal hyperostosis. The enthesopathy leads to the ossification of the anterior longitudinal ligament of the spine and causes the formation of flowing osteophytes, while intervertebral disc space is quite preserved in early phases of the disease. Symptoms of spine involvement are not typical of the disease and consist of pain and stiffness, usually worsened by inaction and damp. It has also been described the ossification of posterior longitudinal ligament which can lead to medullary canal stenosis. Appendicular skeleton is symmetrically involved in early phases of the disease, the most distinctive affected sites being feet, olecranus and patella. Hip involvement is also frequent and may lead to severe disability and represents an important cause of invalidity. The purpose of the present review is to remark on aetiopathogenetic and clinical aspects of diffuse idiopathic skeletal hyperostosis.

  7. AZ-TH, 80 KWE Solar Dish-Stirling Facility

    Energy Technology Data Exchange (ETDEWEB)

    Osuna, R.; Enrile, J.; Sanchez, M.; Fernandez-Quero, V.; Barragan, J.; Ruiz, V.; Silva, M.; Bas, F.; Lopez-Lara, G.; Fernandez-Liebre, F.

    2006-07-01

    Ing. Jose Barragan, Solucar R and D, Avda. Buhaira 2, E-41018 Sevilla, Spain, Tel: +34 95 4937111; Fax: +34 95 4937008; jose.barragan@solucarrd.abengoa.com Abstract. An initiative to promote a 80kWe dish-stirling facility is being carried out by Solucar, an Abengoa company working on solar energy, with the support of the Renewable Energies Program of Andalusia Government TROUGH the Agencia de Innovacion (IDEA), and the Agencia Andaluza de la Energia (AAE). The plant consists of 7 stirling dishes of 11,2kWe unitary power, that will generate 104MWh of electricity in a year, and will sell it to the grid in a commercial basis under the frame of solar thermal renewable energy production regulations in Spain, that consider up to 0,18/kWh over pool market price for electricity. To achieve the feasibility of the project, a new concentrator based on single spherical 0,5 m2 curved mirrors has been proposed. It has been developed following the schemes of the traditional pedestal/arms heliostats. Foreseen cost for concentrator reaches 450/m2 when completely installed and in operation. The facility will be installed in the area of PS10 and Sevilla PV plants, in the solar park that Abengoa is promoting in Sanlucar la Mayor, in order to share maintenance, supervision, vigilance and operation costs with other bigger plants. (Author)

  8. Combined Heat & Power Using the Infinia Concentrated Solar CHP PowerDish System

    Science.gov (United States)

    2013-08-01

    FINAL REPORT Combined Heat & Power Using the Infinia Concentrated Solar CHP PowerDish System ESTCP Project EW-201145 AUGUST 2013...Combined Heat & Power Using the Infinia Concentrated Solar CHP PowerDish System 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6...demonstrated the capabilities of the Infinia PowerDish? CHP technology to generate clean solar thermal and electric energy compatible with domestic and

  9. The Nonlinear Instability Modes of Dished Shallow Shells under Circular Line Loads

    OpenAIRE

    Liu Chang-Jiang; Zheng Zhou-Lian; Huang Cong-Bing; He Xiao-Ting; Sun Jun-Yi; Chen Shan-Lin

    2011-01-01

    This paper investigated the nonlinear stability problem of dished shallow shells under circular line loads. We derived the dimensionless governing differential equations of dished shallow shell under circular line loads according to the nonlinear theory of plates and shells and solved the governing differential equations by combing the free-parameter perturbation method (FPPM) with spline function method (SFM) to analyze the nonlinear instability modes of dished shallow shell under circular l...

  10. Galileo satellite antenna modeling

    Science.gov (United States)

    Steigenberger, Peter; Dach, Rolf; Prange, Lars; Montenbruck, Oliver

    2015-04-01

    The space segment of the European satellite navigation system Galileo currently consists of six satellites. Four of them belong to the first generation of In-Orbit Validation (IOV) satellites whereas the other two are Full Operational Capability (FOC) satellites. High-precision geodetic applications require detailed knowledge about the actual phase center of the satellite and receiver antenna. The deviation of this actual phase center from a well-defined reference point is described by phase center offsets (PCOs) and phase center variations (PCVs). Unfortunately, no public information is available about the Galileo satellite antenna PCOs and PCVs, neither for the IOV, nor the FOC satellites. Therefore, conventional values for the IOV satellite antenna PCOs have been adopted for the Multi-GNSS experiment (MGEX) of the International GNSS Service (IGS). The effect of the PCVs is currently neglected and no PCOs for the FOC satellites are available yet. To overcome this deficiency in GNSS observation modeling, satellite antenna PCOs and PCVs are estimated for the Galileo IOV satellites based on global GNSS tracking data of the MGEX network and additional stations of the legacy IGS network. Two completely independent solutions are computed with the Bernese and Napeos software packages. The PCO and PCV values of the individual satellites are analyzed and the availability of two different solutions allows for an accuracy assessment. The FOC satellites are built by a different manufacturer and are also equipped with another type of antenna panel compared to the IOV satellites. Signal transmission of the first FOC satellite has started in December 2014 and activation of the second satellite is expected for early 2015. Based on the available observations PCO estimates and, optionally PCVs of the FOC satellites will be presented as well. Finally, the impact of the new antenna model on the precision and accuracy of the Galileo orbit determination is analyzed.

  11. Activity and accomplishments of dish/Stirling electric power system development

    Science.gov (United States)

    Livingston, F. R.

    1985-01-01

    The development of the solar parabolic-dish/Stirling-engine electricity generating plant known as the dish/Stirling electric power system is described. The dish/Stirling electric power system converts sunlight to electricity more efficiently than any known existing solar electric power system. The fabrication and characterization of the test bed concentrators that were used for Stirling module testing and of the development of parabolic dish concentrator No. 2, an advanced solar concentrator unit considered for use with the Stirling power conversion unit is discussed.

  12. Regional food dishes in the Brazilian National School Food Program: Acceptability and nutritional composition

    Directory of Open Access Journals (Sweden)

    Diogo thimoteo da Cunha

    2014-08-01

    Full Text Available Objective: the objective of this study was to evaluate the nutritional composition and describe the acceptability of regional culinary dishes served to students from public schools of rural and urban areas. Methods: Ten Brazilian regional dishes were evaluated for acceptability and nutritional composition. the survey was conducted in schools located in rural and urban areas of two cities in the state of São Paulo. Dish acceptability was evaluated using leftover analysis and a 5-point facial hedonic scale. the adherence index was calculated and used as an indirect measure of acceptance, and the nutritional composition was calculated based on the technical files of each dish. Results: A total of 2,384 students from 20 schools participated in the study and 1,174 tasted and evaluated the dishes. the test using the 5-point facial hedonic scale demonstrated that five dishes (Caldo verde soup, persimmon jelly, chicken with okra, puréed cornmeal with spinach, and arugula pizza had an acceptability rate above 85.0%. the mean adherence indices were 57.3% and 55.6% in urban and rural environments, respectively. Analysis of the nutritional composition of regional dishes indicates that these dishes can partially meet macronutrient recommendations. Conclusion: the tested dishes can become part of school menus as they were accepted or partly accepted by the students regardless of school location, whether rural or urban. the cultural heritage is an important resource for the food sovereignty of a country and should be constantly encouraged.

  13. Status of the Boeing Dish Engine Critical Component Project

    Energy Technology Data Exchange (ETDEWEB)

    Brau, H.W.; Diver, R.B.; Nelving, H.; Stone, K.W.

    1999-01-08

    The Boeing Company's Dish Engine Critical Component (DECC) project started in April of 1998. It is a continuation of a solar energy program started by McDonnell Douglas (now Boeing) and United Stirling of Sweden in the mid 1980s. The overall objectives, schedule, and status of this project are presented in this paper. The hardware test configuration, hardware background, operation, and test plans are also discussed. A summary is given of the test data, which includes the daily power performance, generated energy, working-gas usage, mirror reflectivity, solar insolation, on-sun track time, generating time, and system availability. The system performance based upon the present test data is compared to test data from the 1984/88 McDonnell Douglas/United Stirling AB/Southem California Edison test program. The test data shows that the present power, energy, and mirror performance is comparable to when the hardware was first manufactured 14 years ago.

  14. Commercialization of dish-Stirling solar terrestrial systems

    Science.gov (United States)

    Ross, Brad; Penswick, Barry; White, Maury; Cooper, Martin; Farbman, Gerald

    1990-01-01

    The requirements for dish-Stirling commercialization are described. The requirements for practical terrestrial power systems, both technical and economic, are described. Solar energy availability, with seasonal and regional variations, is discussed. The advantages and disadvantages of hybrid operation are listed. The two systems described use either a 25-kW free-piston Stirling hydraulic engine or a 5-kW kinematic Stirling engine. Both engines feature long-life characteristics that result from the use of welded metal bellows as hermetic seals between the working gas and the crankcase fluid. The advantages of the systems, the state of the technology, and the challenges that remain are discussed. Technology transfer between solar terrestrial Stirling applications and other Stirling applications is predicted to be important and synergistic.

  15. Dishing up the Data: A Decade of Space Missions

    CERN Document Server

    Sarkissian, John

    2012-01-01

    The past decade has seen Parkes once again involved in a wide range of space tracking activities that have added to its illustrious legacy. This contribution is a personal recollection of those tracking efforts - both real and celluloid. We begin in a light-hearted vein with some behind-the-scenes views of the popular film, "The DISH", and then turn to more serious contributions; discussing the vital role of the telescope in alleviating the great "traffic jam" at Mars in 2003/04 and salvaging the Doppler Wind Experiment as the Huygens probe descended though the atmosphere of Saturn's largest moon, Titan, in mid-decade. We cap off the decade with a discussion of the search for the missing Apollo 11 slow-scan TV tapes.

  16. Analysis Groove Characteristics of Friction Dishes in Wet Speeding Clutch

    Institute of Scientific and Technical Information of China (English)

    HongYue; LiuJin; JinShiliang

    2004-01-01

    The impacts of different groove shapes, numbers, and angle of friction dish on transmitting torque, speed, push pressure in wet speeding clutch are discussed in this paper. Since the wet speeed governing clutch works within hydrodynamic lubrication mixture lubrication. boundary, lubrication and contact situation, the oils combining with a-hydrocarbon or polyester are getting widely used as lubricant.The power-law fluid model with Patir-Cheng average flow model, GT asperity contact model and oil film inertia are applied for average Reynolds equation setting, In order to investigate the relationship between average push pressure within hydrodynamic lubrication and mixture lubrication, average transmitting torque and output speed, the numeral calculation and analysis are presented. According to calculation, it is found that the groove shape, groove angle and groove numbers affect the average transfer torque and push pressure with the speed rate.

  17. Simulations for single-dish intensity mapping experiments

    CERN Document Server

    Bigot-Sazy, M -A; Battye, R A; Browne, I W A; Ma, Y -Z; Maffei, B; Noviello, F; Remazeilles, M; Wilkinson, P N

    2015-01-01

    HI intensity mapping is an emerging tool to probe dark energy. Observations of the redshifted HI signal will be contaminated by instrumental noise, atmospheric and Galactic foregrounds. The latter is expected to be four orders of magnitude brighter than the HI emission we wish to detect. We present a simulation of single-dish observations including an instrumental noise model with 1/f and white noise, and sky emission with a diffuse Galactic foreground and HI emission. We consider two foreground cleaning methods: spectral parametric fitting and principal component analysis. For a smooth frequency spectrum of the foreground and instrumental effects, we find that the parametric fitting method provides residuals that are still contaminated by foreground and 1/f noise, but the principal component analysis can remove this contamination down to the thermal noise level. This method is robust for a range of different models of foreground and noise, and so constitutes a promising way to recover the HI signal from the ...

  18. Commercialization of dish-Stirling solar terrestrial systems

    Science.gov (United States)

    Ross, Brad; Penswick, Barry; White, Maury; Cooper, Martin; Farbman, Gerald

    1990-01-01

    The requirements for dish-Stirling commercialization are described. The requirements for practical terrestrial power systems, both technical and economic, are described. Solar energy availability, with seasonal and regional variations, is discussed. The advantages and disadvantages of hybrid operation are listed. The two systems described use either a 25-kW free-piston Stirling hydraulic engine or a 5-kW kinematic Stirling engine. Both engines feature long-life characteristics that result from the use of welded metal bellows as hermetic seals between the working gas and the crankcase fluid. The advantages of the systems, the state of the technology, and the challenges that remain are discussed. Technology transfer between solar terrestrial Stirling applications and other Stirling applications is predicted to be important and synergistic.

  19. Secondary concentrators for parabolic dish solar thermal power systems

    Science.gov (United States)

    Jaffe, L. D.; Poon, P. T.

    1981-01-01

    A variety of different concepts are currently being studied with the objective to lower the cost of parabolic mirrors and to provide alternatives. One of the considered approaches involves the use of compound concentrators. A compound solar concentrator is a concentrator in which the sunlight is reflected or refracted more than once. It consists of a primary mirror or lens, whose aperture determines the amount of sunlight gathered, and a smaller secondary mirror or lens. Additional small optical elements may also be incorporated. The possibilities and problems regarding a use of compound concentrators in parabolic dish systems are discussed. Attention is given to concentrating secondary lenses, secondary imaging and concentrating mirrors, conical secondary mirrors, compound elliptic secondary concentrating mirrors, and hyperbolic trumpet secondary concentrating mirrors.

  20. Thermal Model of a Dish Stirling Cavity-Receiver

    Directory of Open Access Journals (Sweden)

    Rubén Gil

    2015-01-01

    Full Text Available This paper presents a thermal model for a dish Stirling cavity based on the finite differences method. This model is a theoretical tool to optimize the cavity in terms of thermal efficiency. One of the main outcomes of this work is the evaluation of radiative exchange using the radiosity method; for that purpose, the view factors of all surfaces involved have been accurately calculated. Moreover, this model enables the variation of the cavity and receiver dimensions and the materials to determine the optimal cavity design. The tool has been used to study the cavity optimization regarding geometry parameters and material properties. Receiver absorptivity has been identified as the most influential property of the materials. The optimal aperture height depends on the minimum focal space.

  1. Dependency of dishing on polish time and slurry chemistry in Cu CMP

    NARCIS (Netherlands)

    Nguyen Hoang, V.; van Kranenburg, H.; Woerlee, P.H.

    2000-01-01

    In this paper the influences of slurry chemistry and thickness of the copper layer on dishing will be discussed. The dishing is studied for different patterns and variable polishing times. We found that the concentration of the oxidiser and the thickness of copper layer have a strong impact on

  2. On Approaches to C-E Translation of Chinese Dish Names

    Institute of Scientific and Technical Information of China (English)

    ZHANG Zi-shun

    2015-01-01

    Literal translation and free translation are the most common methods of translation. It may be accepted that either the two methods or one, or neither on account of the different understandings of the two methods. The author tries to probe into some approaches to C-E translation of Chinese dish names according to the contrastive studies between Chinese and English dish names.

  3. Dish Stirling High Performance Thermal Storage FY14Q3 Quad Chart.

    Energy Technology Data Exchange (ETDEWEB)

    Andraka, Charles E. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2014-07-01

    The project goals are: demonstrate the feasibility of significant thermal storage for dish Stirling systems to leverage their existing high performance to greater capacity; demonstrate key components of a latent storage and transport system enabling on-dish storage with low exergy losses; an provide technology path to a 25kWe system with 6 hours of storage.

  4. Dependency of dishing on polish time and slurry chemistry in Cu CMP

    NARCIS (Netherlands)

    Nguyen, V.; Kranenburg, van H.; Woerlee, P.

    2000-01-01

    In this paper the influences of slurry chemistry and thickness of the copper layer on dishing will be discussed. The dishing is studied for different patterns and variable polishing times. We found that the concentration of the oxidiser and the thickness of copper layer have a strong impact on dishi

  5. Layout Optimization for the Dishes Installed on a Rotating Table——The Packing Problem With Equilibrium Behavioural Constraints

    Institute of Scientific and Technical Information of China (English)

    滕弘飞; 孙守林; 葛文海; 钟万勰

    1994-01-01

    The layout optimization for the dishes installed on a rotating table is investigated. This is a packing problem with equilibrium behavioural constraints. To deal with its layout topo-models and initial layout, a mathematical model and heuristic approaches, including the method of model-changing iteration (MCI) and the method of main objects topo-models (MOT), are proposed, with a series of intuitive algorithms embedded in, such as the technique for the search under the initial guess and the strategies for remission of "combinatorial explosion" . The validity and reliability of the proposed algorithms are verified by numerical examples and engineering applications, which could be used in satellite module, multiple spindle box, rotating structure and so on.

  6. Diffuse Idiopathic Skeletal Hyperostosis (DISH) and Impaired Physical Function: The Rancho Bernardo Study.

    Science.gov (United States)

    Katzman, Wendy B; Huang, Mei-Hua; Kritz-Silverstein, Donna; Barrett-Connor, Elizabeth; Kado, Deborah M

    2017-07-01

    Investigate associations of diffuse idiopathic skeletal hyperostosis (DISH) with self-reported and measured physical function in older adults. Cross-sectional analyses of data collected in 1992-96 from a longitudinal cohort. Research clinic within a community. Community-dwelling men (n = 630) and women (n = 961), mean age 71.5 years (SD = 10.8), from the Rancho Bernardo Study. DISH assessed from lateral thoracic and lumbar spine radiographs; self-reported difficulty bending over to the floor, walking 2-3 level blocks, or climbing 1 flight of stairs; performance-based measures of grip strength and chair-stand testing (ability to stand up and sit down in a chair 5 times without using chair arms). DISH was present in 25.6% of men and 5.5% of women. In age and sex-adjusted models, those with DISH had 1.72-fold increased odds (95% CI: 1.13, 2.62) of self-reported difficulty bending; this remained significant after further adjustment for Cobb angle, weight, stroke, arthritis, and exercise, OR = 1.69, (95% CI: 1.07, 2.66). In fully adjusted multivariate models, those with DISH had worse grip strength, -1.08 kg, P = .01, but did not differ from those without DISH on walking or climbing stairs. In sex-stratified, fully adjusted models, among men only, those with DISH were 2.17-times (95% CI: 1.04, 4.52) more likely to be unable to complete 5 chair stands without using their arms. DISH was less prevalent in women but affected almost one-quarter of older white men. People with DISH are more likely to experience physical functional impairment, suggesting that DISH has clinical correlations and is not an incidental radiographic finding. © 2017, Copyright the Authors Journal compilation © 2017, The American Geriatrics Society.

  7. Dish-based CPV-T for rooftop generation

    Science.gov (United States)

    Davila-Peralta, Christian; Hyatt, Justin; Alfred, Dan; Struble, Morgan; Sodari, Frank; Angel, Roger

    2017-09-01

    Hybrid CPV-T with combined electrical and thermal output is well suited to solar generation from fixed limited areas, such as on the roof of an industrial or commercial facility with need for heat. This application will become especially attractive once overall electrical conversion efficiency of 40% is reached, as is projected for REhnu CPV systems using multijunction cells of 50% efficiency, anticipated in a few years. We outline here a configuration of dish- based CPV trackers optimized for close packing on a flat roof in a triangular grid, with a mirror area-to-ground area ratio of 50%. When the geometry of shadowing averaged over a year is taken into account, 80% of all the sunlight that would strike the rooftop is directed into the receivers. Such an array on a given area of flat roof will generate more electrical energy than would be possible with conventional PV panels, even if covering the entire rooftop, because of silicon's relative inefficiency. For example, in Tucson, the annual average global flux of 5.7 kWh/m2/day on a horizontal surface covered with 22% silicon modules will yield 1.25 kWh/m2/day. We show that a CPV system collecting 80% of all the direct sunlight of 7.0 kWh/m2 and converting it with 40% efficiency will yield 2.24 kWh/m2/day of rooftop area, nearly twice as much4. Thermal power will double again the total energy yield. A dual axis CPV-T tracker designed specifically very close spacing has been built to carry a single dish mirror of the standard type used in REhnu's M-8 generator, described by Stalcup et al in these proceedings1,2. Sunlight is collected and focused by a single square paraboloidal mirror, 1.65 × 1.65 m with focal length of 1.5 m. For closest possible packing without mechanical interference, and for broad distribution of load on a rooftop, the mirror and receiver are mounted to a C-ring structure, configured such that the elevation and azimuth axes intersect at a virtual pivot, at the center of the sphere that just

  8. Testing of the SAIC facets on the stretched-membrane dish

    Science.gov (United States)

    Grossman, J. W.; Erdman, W. W.; Houser, R. M.; Davenport, R.

    1994-04-01

    A dish structure sized for a 25 kW electric dish/generator system has been installed at the National Solar Thermal Test Facility (NSTTF). The dish is used as an optical test bed for prototype stretched-membrane facets. Sandia procured twelve (12) stretched-membrane facets from Science Applications International Corporation (SAIC) for installation on the dish structure. Individual facet optical performance was measured using the 2f test method under development at Sandia. Four facets were tested on-sun using the test truss at the NSTTF prior to installation on the dish structure. During the final stages of the structure assembly, the facets were installed for testing. A distant light source alignment technique was used to align the facets to a 9 meter focal length. The alignment and focus were optimized with on-sun measurements of individual facet characteristics. On-sun flux maps of the image were made using the Beam Characterization System. Calorimetry tests were performed using a cold water calorimeter. This data was used to create a power intercept curve and predict the power inside apertures of different sizes. The focal plane was moved to 9.95 meters and the alignment, optimization, and on-sun tests repeated. This paper presents the results of the testing on the individual facets as well as the results of testing the dish system. The effects of the change in focal length on the optical performance of the dish are shown in the results.

  9. Optimization of Dish Solar Collectors with and without Secondary Concentrators

    Science.gov (United States)

    Jaffe, L. D.

    1982-01-01

    Methods for optimizing parabolic dish solar collectors and the consequent effects of various optical, thermal, mechanical, and cost variables are examined. The most important performance optimization is adjusting the receiver aperture to maximize collector efficiency. Other parameters that can be adjusted to optimize efficiency include focal length, and, if a heat engine is used, the receiver temperature. The efficiency maxima associated with focal length and receiver temperature are relatively broad; it may, accordingly, be desirable to design somewhat away from the maxima. Performance optimization is sensitive to the slope and specularity errors of the concentrator. Other optical and thermal variables affecting optimization are the reflectance and blocking factor of the concentrator, the absorptance and losses of the receiver, and, if a heat engine is used, the shape of the engine efficiency versus temperature curve. Performance may sometimes be improved by use of an additional optical element (a secondary concentrator) or a receiver window if the errors of the primary concentrator are large or the receiver temperature is high.

  10. Test results on parabolic dish concentrators for solar thermal power systems

    Science.gov (United States)

    Jaffe, Leonard D.

    1989-01-01

    This paper presents results of development testing of various solar thermal parabolic dish concentrators. The concentrators were mostly designed for the production of electric power using dish-mounted Rankine, Brayton or Stirling cycle engines, intended to be produced at low cost. Measured performance for various dishes included optical efficiencies ranging from 0.32 to 0.86 at a geometric concentration ratio of 500, and from about 0.09 to 0.85 at a geometric concentration ratio of 3000. Some malfunctions were observed. The tests should provide operating information of value in developing concentrators with improved performance and reduced maintenance.

  11. Test results on parabolic dish concentrators for solar thermal power systems

    Science.gov (United States)

    Jaffe, Leonard D.

    1989-01-01

    This paper presents results of development testing of various solar thermal parabolic dish concentrators. The concentrators were mostly designed for the production of electric power using dish-mounted Rankine, Brayton or Stirling cycle engines, intended to be produced at low cost. Measured performance for various dishes included optical efficiencies ranging from 0.32 to 0.86 at a geometric concentration ratio of 500, and from about 0.09 to 0.85 at a geometric concentration ratio of 3000. Some malfunctions were observed. The tests should provide operating information of value in developing concentrators with improved performance and reduced maintenance.

  12. Manufacturing cost analysis of a parabolic dish concentrator (General Electric design) for solar thermal electric power systems in selected production volumes

    Science.gov (United States)

    1981-01-01

    The manufacturing cost of a General Electric 12 meter diameter concentrator was estimated. This parabolic dish concentrator for solar thermal system was costed in annual production volumes of 100 - 1,000 - 5,000 - 10,000 - 50,000 100,000 - 400,000 and 1,000,000 units. Presented for each volume are the costs of direct labor, material, burden, tooling, capital equipment and buildings. Also presented is the direct labor personnel and factory space requirements. All costs are based on early 1981 economics.

  13. Design of Maritime Satellite Navigation Equipment Man-Machine Interactive Software Based on ReWorks Operating System%基于ReWorks操作系统海用卫星导航设备人机交互软件开发

    Institute of Scientific and Technical Information of China (English)

    2015-01-01

    针对海用卫星导航设备人机交互软件,引入了ReWorks操作系统,研究了基于ReWorks的应用软件开发方法,使用ReDe开发环境和DirectX工具实现了海用卫星导航设备人机交互软件的设计开发,最后工程实践表明其正确性和有效性。%According to maritime satellite navigation equipment man-machine interactive software, ReWorks operating system is introduced, software development methods Based on ReWorks operating system is studied, maritime satellite navigation equipment man-machine interactive software design is realized by using the development environment of ReDe and DirectX tool. The final project application proved its correctness and effectiveness.

  14. Living antennas on communication satellites

    DEFF Research Database (Denmark)

    Lumholt, Michael

    2003-01-01

    Crises change the global pattern of communication. The communications problems occur because the satellites are optimized to cover specific geographic areas, and these areas cannot be altered once the satellites are in Earth orbit. An effective solution to the problem is to equip communication...... satellites with "living" antennas that can adjust their radiation coverage areas according to the new demands. The development of living antennas is, therefore, among the focus areas identified and supported by the European Space Agency, ESA....

  15. Metagenomic data of fungal internal transcribed spacer from serofluid dish, a traditional Chinese fermented food

    Directory of Open Access Journals (Sweden)

    Peng Chen

    2016-03-01

    Full Text Available Serofluid dish (or Jiangshui, in Chinese, a traditional food in the Chinese culture for thousands of years, is made from vegetables by fermentation. In this work, microorganism community of the fermented serofluid dish was investigated by the culture-independent method. The metagenomic data in this article contains the sequences of fungal internal transcribed spacer (ITS regions of rRNA genes from 12 different serofluid dish samples. The metagenome comprised of 50,865 average raw reads with an average of 8,958,220 bp and G + C content is 45.62%. This is the first report on metagenomic data of fungal ITS from serofluid dish employing Illumina platform to profile the fungal communities of this little known fermented food from Gansu Province, China. The Metagenomic data of fungal internal transcribed spacer can be accessed at NCBI, SRA database accession no. SRP067411.

  16. Metagenomic data of fungal internal transcribed spacer from serofluid dish, a traditional Chinese fermented food.

    Science.gov (United States)

    Chen, Peng; Zhao, Yang; Wu, Zhengrong; Liu, Ronghui; Xu, Ruixiang; Yan, Lei; Li, Hongyu

    2016-03-01

    Serofluid dish (or Jiangshui, in Chinese), a traditional food in the Chinese culture for thousands of years, is made from vegetables by fermentation. In this work, microorganism community of the fermented serofluid dish was investigated by the culture-independent method. The metagenomic data in this article contains the sequences of fungal internal transcribed spacer (ITS) regions of rRNA genes from 12 different serofluid dish samples. The metagenome comprised of 50,865 average raw reads with an average of 8,958,220 bp and G + C content is 45.62%. This is the first report on metagenomic data of fungal ITS from serofluid dish employing Illumina platform to profile the fungal communities of this little known fermented food from Gansu Province, China. The Metagenomic data of fungal internal transcribed spacer can be accessed at NCBI, SRA database accession no. SRP067411.

  17. Regional food dishes in the Brazilian National School Food Program: Acceptability and nutritional composition

    National Research Council Canada - National Science Library

    Cunha, Diogo thimoteo da; Gonçalves, Hélida Ventura Barbosa; Lima, Aline Fátima Andrade de; Martins, Paula Andrea; Rosso, Veridiana Vera de; Stedefeldt, Elke

    2014-01-01

    Objective: the objective of this study was to evaluate the nutritional composition and describe the acceptability of regional culinary dishes served to students from public schools of rural and urban areas.Methods...

  18. Temperature gradients drive radial fluid flow in Petri dishes and multiwell plates.

    Science.gov (United States)

    Lindsay, Stephen M; Yin, John

    2016-06-01

    Liquid in a Petri dish spontaneously circulates in a radial pattern, even when the dish is at rest. These fluid flows have been observed and utilized for biological research, but their origins have not been well-studied. Here we used particle-tracking to measure velocities of radial fluid flows, which are shown to be linked to evaporation. Infrared thermal imaging was used to identify thermal gradients at the air-liquid interface and at the bottom of the dish. Two-color ratiometric fluorescence confocal imaging was used to measure thermal gradients in the vertical direction within the fluid. A finite-element model of the fluid, incorporating the measured temperature profiles, shows that buoyancy forces are sufficient to produce flows consistent with the measured particle velocity results. Such flows may arise in other dish or plate formats, and may impact biological research in positive or negative ways.

  19. Anti-Satellite Weapons, Countermeasures, and Arms Control

    Science.gov (United States)

    2007-11-02

    From Kosmos 1500 38 3-3. Imagery Obtained by Synthetic-Aperture Satellite Radar 40 Chapter 3 MILSATs, ASATs, and National Security THE ROLE AND...satellite capabil- ities, such as resolution. For example, Soviet oceanographic radar satellites of the Kosmos - 1500 class can obtain radar imagery with...surveillance satellite ( Kosmos 1500) equipped with a side-looking radar and in the same year placed two satellites (Venera 15 and Venera 16) equipped

  20. Design, Analysis and Optimization of a Solar Dish/Stirling System

    OpenAIRE

    Seyyed Danial Nazemi; Mehrdad Boroushaki

    2016-01-01

    In this paper, a mathematical model by which the thermal and physical behavior of a solar dish/Stirling system was investigated, then the system was designed, analysed and optimized. In this regard, all of heat losses in a dish/Stirling system were calculated, then, the output net-work of the Stirling engine was computed, and accordingly, the system efficiency was worked out. These heat losses include convection and conduction heat losses, radiation heat losses by emission in the cavity recei...

  1. DISH STIRLING SYSTEM POTENTIAL ASSESSMENT FOR EIGHT MAIN SITES IN MADAGASCAR

    OpenAIRE

    Praene, Jean-Philippe; Radanielina, Harimisa; Rakotondramiarana, Hery Tiana

    2016-01-01

    International audience; Solar energy is a green and attractive renewable energy source that can be converted for power generation. The objective of this work is to evaluate the potential of dish Stirling systems if they are used in the fourth worldwide largest island of Madagascar. For that purpose, a theoretical model of the dish Stirling system based on the geometrical configuration and heat transfer was developed and coded on Matlab. Simulations were run to investigate the energy efficienc...

  2. Faults Analysis and Diagnosis of DR J-460 Dish Centrifugal Separator's Helical Gear

    Institute of Scientific and Technical Information of China (English)

    MA Xiao-jian; GAN Xue-hui

    2004-01-01

    The main faults of dish centrifugal separator's helical gear are described in this paper. In order to diagnose the DR J-460 dish centrifugal separator correctly, the vibration is tested with a helical gear under both normal and abnormal conditions. After comparing several general methods of the gear's fault feature extraction, a new convenient and effective method is presented on the basis of analyzing the vibration spectrum under different rotary velocities.

  3. Dish Stirling High Performance Thermal Storage FY14Q4 Quad Chart

    Energy Technology Data Exchange (ETDEWEB)

    Andraka, Charles E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-10-01

    The goals of this project are to demonstrate the feasibility of significant thermal storage for dish stirling systems to leverage their existing high performance to greater capacity; demonstrate key components of a latent storage and transport system enabling on-dish storage with low energy losses; and provide a technology path to a 25kWe system with 6 hours of storage.

  4. Sterile polystyrene culture dishes induce transformation of polyps into medusae in Aurelia aurita (Scyphozoa, Cnidaria).

    Science.gov (United States)

    Herrmann, Klaus; Siefker, Barbara; Berking, Stefan

    2003-01-01

    Polyps of Aurelia aurita produce medusae once a year. Under laboratory conditions this process, termed strobilation, can be induced by lowering the incubation temperature for about two weeks. Here we report a fast induction of strobilation by sterile polystyrene culture dishes. The effect is abolished when the culture dishes are washed twice with hot water prior to the experiment. We recommend that polystyrene cultureware should be pre-washed whenever there is an indication of unusual effects.

  5. Satellite Communication.

    Science.gov (United States)

    Technology Teacher, 1985

    1985-01-01

    Presents a discussion of communication satellites: explains the principles of satellite communication, describes examples of how governments and industries are currently applying communication satellites, analyzes issues confronting satellite communication, links mathematics and science to the study of satellite communication, and applies…

  6. A satellite-tracking millimeter-wave reflector antenna system for mobile satellite-tracking

    Science.gov (United States)

    Densmore, Arthur C. (Inventor); Jamnejad, Vahraz (Inventor); Woo, Kenneth E. (Inventor)

    1995-01-01

    A miniature dual-band two-way mobile satellite tracking antenna system mounted on a movable ground vehicle includes a miniature parabolic reflector dish having an elliptical aperture with major and minor elliptical axes aligned horizontally and vertically, respectively, to maximize azimuthal directionality and minimize elevational directionality to an extent corresponding to expected pitch excursions of the movable ground vehicle. A feed-horn has a back end and an open front end facing the reflector dish and has vertical side walls opening out from the back end to the front end at a lesser horn angle and horizontal top and bottom walls opening out from the back end to the front end at a greater horn angle. An RF circuit couples two different signal bands between the feed-horn and the user. An antenna attitude controller maintains an antenna azimuth direction relative to the satellite by rotating it in azimuth in response to sensed yaw motions of the movable ground vehicle so as to compensate for the yaw motions to within a pointing error angle. The controller sinusoidally dithers the antenna through a small azimuth dither angle greater than the pointing error angle while sensing a signal from the satellite received at the reflector dish, and deduces the pointing angle error from dither-induced fluctuations in the received signal.

  7. Satellite-Tracking Millimeter-Wave Reflector Antenna System For Mobile Satellite-Tracking

    Science.gov (United States)

    Densmore, Arthur C. (Inventor); Jamnejad, Vahraz (Inventor); Woo, Kenneth E. (Inventor)

    2001-01-01

    A miniature dual-band two-way mobile satellite-tracking antenna system mounted on a movable vehicle includes a miniature parabolic reflector dish having an elliptical aperture with major and minor elliptical axes aligned horizontally and vertically, respectively, to maximize azimuthal directionality and minimize elevational directionality to an extent corresponding to expected pitch excursions of the movable ground vehicle. A feed-horn has a back end and an open front end facing the reflector dish and has vertical side walls opening out from the back end to the front end at a lesser horn angle and horizontal top and bottom walls opening out from the back end to the front end at a greater horn angle. An RF circuit couples two different signal bands between the feed-horn and the user. An antenna attitude controller maintains an antenna azimuth direction relative to the satellite by rotating it in azimuth in response to sensed yaw motions of the movable ground vehicle so as to compensate for the yaw motions to within a pointing error angle. The controller sinusoidally dithers the antenna through a small azimuth dither angle greater than the pointing error angle while sensing a signal from the satellite received at the reflector dish, and deduces the pointing angle error from dither-induced fluctuations in the received signal.

  8. It is Time for a Change:Petri Dishes Weaken Cells

    Institute of Scientific and Technical Information of China (English)

    Andrei P.Sommer; Mike Kh.Haddad; Hans-Joerg Fecht

    2012-01-01

    We wish to draw the attention to a potential deficiency in the biocompatibility of polystyrene cell culturc dishes which is caused by a softening of the material under relevant culture conditions.The finding confirms the central hypothesis of our previous model study.In it we assumed a local increase in pH at the interface between the hydrophilic polymer and liquid.The finding is of considerable biological interest.Polystyrene tissue culture dishes are now in use for 50 years.To the best of our knowledge their biocompatibility has never been challenged.Here we report the first experimental proof that exposure to water softens the surface of polystyrene Petri dishes.We expect that our results will stimulate the development ofa new generation of cell culture devices,including Petri dishes and culture flasks,and the establishment of improved biomimetic settings for tissuc engineering and stem cell research.New non-swelling biomaterials or nanocoatings designed to reduce the swelling of polymer culture dishes could improve cell performance.The need for further study is clear.

  9. Cultured articular chondrocytes sheets for partial thickness cartilage defects utilizing temperature-responsive culture dishes

    Directory of Open Access Journals (Sweden)

    N Kaneshiro

    2007-05-01

    Full Text Available The extracellular matrix (ECM of articular cartilage has several functions that are unique to joints. Although a technique for transplanting cultured chondrocytes has already been introduced, it is difficult to collect intact ECM when using enzymes to harvest samples. Temperature-responsive culture dishes have already been clinically applied in the fields of myocardial and corneal transplantation. Earlier studies have shown that a sheet of cultured cells with intact ECM and adhesive factors can be harvested using such culture dishes, which allow the surface properties of the dish to be reversibly altered by changing the temperature. Human chondrocytes were subjected to enzymatic digestion and then were seeded in temperature-responsive culture dishes. A sheet of chondrocytes was harvested by only reducing the temperature after the cultured cells reached confluency. A real-time PCR analysis of the chondrocyte sheets confirmed that type II collagen, aggrecan, and fibronectin were present. These results suggested that, although chondrocytes undergo dedifferentiation in a monolayer culture, multilayer chondrocyte sheets grown in a similar environment to that of three-dimensional culture may be able to maintain a normal phenotype. A histological examination suggested that multilayer chondrocyte sheets could thus prevent the loss of proteoglycans because the area covered by the sheets was well stained by safranin-O. The present experiments suggested that temperature-responsive culture dishes are useful for obtaining cultured chondrocytes, which may then be clinically employed as a substitute for periosteal patches because such sheets can be applied without a scaffold.

  10. Thermal buffering of receivers for parabolic dish solar thermal power plants

    Science.gov (United States)

    Manvi, R.; Fujita, T.; Gajanana, B. C.; Marcus, C. J.

    1980-01-01

    A parabolic dish solar thermal power plant comprises a field of parabolic dish power modules where each module is composed of a two-axis tracking parabolic dish concentrator which reflects sunlight (insolation) into the aperture of a cavity receiver at the focal point of the dish. The heat generated by the solar flux entering the receiver is removed by a heat transfer fluid. In the dish power module, this heat is used to drive a small heat engine/generator assembly which is directly connected to the cavity receiver at the focal point. A computer analysis is performed to assess the thermal buffering characteristics of receivers containing sensible and latent heat thermal energy storage. Parametric variations of the thermal inertia of the integrated receiver-buffer storage systems coupled with different fluid flow rate control strategies are carried out to delineate the effect of buffer storage, the transient response of the receiver-storage systems and corresponding fluid outlet temperature. It is concluded that addition of phase change buffer storage will substantially improve system operational characteristics during periods of rapidly fluctuating insolation due to cloud passage.

  11. Dorsal vertebral column abnormalities in dogs with disseminated idiopathic skeletal hyperostosis (DISH).

    Science.gov (United States)

    Decker, S De; Volk, H A

    2014-06-21

    Although disseminated idiopathic skeletal hyperostosis (DISH) most often affects the ventral aspect of the vertebral column, this study evaluated the occurrence, nature and clinical relevance of dorsal vertebral column abnormalities in 10 dogs with DISH for which CT or MRI and a complete neurological examination were available. Dorsal vertebral column abnormalities were present in eight dogs and included articular process hypertrophy (n=7 dogs), periarticular new bone formation (n=1), pseudoarthrosis between spinous processes (n=4) and thickening of the dorsal lamina (n=4). These dorsal vertebral abnormalities caused clinically relevant vertebral canal stenosis in six dogs and were the only cause of clinical signs in four of these dogs. Although the lumbosacral joint was not affected by DISH, these six dogs demonstrated lumbosacral vertebral canal stenosis and clinical signs of cauda equina compression, which included paraparesis (n=5 dogs), lumbosacral pain (n=4), urinary incontinence (n=4), faecal incontinence (n=1) and urinary and faecal incontinence (n=1). There is a possible association between DISH and hypertrophy of dorsal vertebral structures, potentially resulting in vertebral canal stenosis. Although these changes occurred at segments fused by DISH, they predominantly affected adjacent non-affected segments.

  12. Space Debris Radar Experiments at the Medicina VLBI Dish

    Science.gov (United States)

    Pupillo, G.; Montebugnoli, S.; Di Martino, M.; Salerno, E.; Bartolini, M.; Pluchino, S.; Schilliro, F.; Anselmo, L.; Portelli, C.; Konovalenko, A.; Nabatov, A.

    2009-03-01

    In 2007 three space debris detection tests were performed in the framework of a monitoring program carried out by the Istituto Nazionale di Astrofisica - INAF - in collaboration with the Italian Space Agency - ASI. The observations were made by using the bistatic radar technique. The INAF 32 m radiotelescope located at Medicina (Bologna, Italy) was used as receiver whereas the Ukrainian 70 m parabolic antenna located at Evpatoria was utilized as transmitter. The aim of the experiment was to test the sensitivity of the Medicina-Evpatoria radar system in space debris detection, and to validate and optimize the hardware setup. Measurements were mainly carried out on inactive satellites and catalogued space debris. However the search for new fragments in LEO was also performed during the campaign. This paper reports on results of these observations.

  13. The Nonlinear Instability Modes of Dished Shallow Shells under Circular Line Loads

    Directory of Open Access Journals (Sweden)

    Liu Chang-Jiang

    2011-01-01

    Full Text Available This paper investigated the nonlinear stability problem of dished shallow shells under circular line loads. We derived the dimensionless governing differential equations of dished shallow shell under circular line loads according to the nonlinear theory of plates and shells and solved the governing differential equations by combing the free-parameter perturbation method (FPPM with spline function method (SFM to analyze the nonlinear instability modes of dished shallow shell under circular line loads. By analyzing the nonlinear instability modes and combining with concrete computational examples, we obtained the variation rules of the maximum deflection area of initial instability with different geometric parameters and loading action positions and discussed the relationship between the initial instability area and the maximum deflection area of initial instability. The results obtained from this paper provide some theoretical basis for engineering design and instability prediction and control of shallow-shell structures.

  14. Comparison of advanced engines for parabolic dish solar thermal power plants

    Science.gov (United States)

    Fujita, T.; Bowyer, J. M.; Gajanana, B. C.

    1980-01-01

    A paraboloidal dish solar thermal power plant produces electrical energy by a two-step conversion process. The collector subsystem is composed of a two-axis tracking paraboloidal concentrator and a cavity receiver. The concentrator focuses intercepted sunlight (direct, normal insolation) into a cavity receiver whose aperture encircles the focal point of the concentrator. At the internal wall of the receiver the electromagnetic radiation is converted to thermal energy. A heat engine/generator assembly then converts the thermal energy captured by the receiver to electricity. Developmental activity has been concentrated on small power modules which employ 11- to 12-meter diameter dishes to generate nominal power levels of approximately 20 kWe. A comparison of advanced heat engines for the dish power module is presented in terms of the performance potential of each engine with its requirements for advanced technology development. Three advanced engine possibilities are the Brayton (gas turbine), Brayton/Rankine combined cycle, and Stirling engines.

  15. Sky reconstruction from transit visibilities: PAON-4 and Tianlai Dish Array

    CERN Document Server

    Zhang, Jiao; Chen, Xuelei; Campagne, Jean-Eric; Magneville, Christophe; Wu, Fengquan

    2016-01-01

    The spherical harmonics $m$-mode decomposition is a powerful sky map reconstruction method suitable for radio interferometers operating in transit mode. It can be applied to various configurations, including dish arrays and cylinders. We describe the computation of the instrument response function, the point spread function (PSF), transfer function, the noise covariance matrix and noise power spectrum. The analysis in this paper is focused on dish arrays operating in transit mode. We show that arrays with regular spacing have more pronounced side lobes as well as structures in their noise power spectrum, compared to arrays with irregular spacing, specially in the north-south direction. A good knowledge of the noise power spectrum $C^{\\mathrm{noise}}(\\ell)$ is essential for intensity mapping experiments as non uniform $C^{\\mathrm{noise}}(\\ell)$ is a potential problem for the measurement of the HI power spectrum. Different configurations have been studied to optimise the PAON-4 and Tianlai dish array layouts. W...

  16. Design, Analysis and Optimization of a Solar Dish/Stirling System

    Directory of Open Access Journals (Sweden)

    Seyyed Danial Nazemi

    2016-02-01

    Full Text Available In this paper, a mathematical model by which the thermal and physical behavior of a solar dish/Stirling system was investigated, then the system was designed, analysed and optimized. In this regard, all of heat losses in a dish/Stirling system were calculated, then, the output net-work of the Stirling engine was computed, and accordingly, the system efficiency was worked out. These heat losses include convection and conduction heat losses, radiation heat losses by emission in the cavity receiver, reflection heat losses of solar energy in the parabolic dish, internal and external conduction heat losses, energy dissipation by pressure drops, and energy losses by shuttle effect in displacer piston in the Stirling engine. All of these heat losses in the parabolic dish, cavity receiver and Stirling engine were calculated using mathematical modeling in MatlabTM software. For validation of the proposed model, a 10 kW solar dish/Stirling system was designed and the simulation results were compared with the Eurodish system data with a reasonable degree of agreement. This model is used to investigate the effect of geometric and thermodynamic parameters including the aperture diameter of the parabolic dish and the cavity receiver, and the pressure of the compression space of the Stirling engine, on the system performance. By using the PSO method, which is an intelligent optimization technique, the total design was optimized and the optimal values of decision-making parameters were determined. The optimization has been done in two scenarios. In the first scenario, the optimal value of each designed parameter has been changed when the other parameters are equal to the designed case study parameters. In the second scenario, all of parameters were assumed in their optimal values. By optimization of the modeled dish/Stirling system, the total efficiency of the system improved to 0.60% in the first scenario and it increased from 21.69% to 22.62% in the second

  17. Drilling equipment

    Energy Technology Data Exchange (ETDEWEB)

    Voyevodin, Yu.M.; Kholosha, Ye.G.; Leshchenko, A.G.; Timchenko, A.I.

    1979-01-10

    The invention refers to units designed for extracting minerals by mechanical action on the face by a cutting tool. There is a known drills which includes a pulse device which contains a combustion chamber, cylinder, piston-percussion tool and cutting tool. The combustion chamber and the sub-piston cavity of the cylinder are connected by a channel in which there is a distributor. Its shortcoming is the fact that the pulse device does not guarantee the necessary motion of the actuating mechanism for its velocity and frequency of the shocks on the cutting tool. This reduces the efficiency of the operation and limits the area of application. The purpose of the proposed invention is to improve productivity of the device. This is achieved because the head of the drill is equipped with a 2-piston pulse device which contains 2-combustion chambers, 2 working cylinders, 2 piston percussion instruments, a rod with gas-conducting and connecting channels for interconnection of the sub-piston cavities and combustion chambers of both cylinders. The spent gases of one cylinder are used for closing the combustion chamber of the second cylinder.

  18. Handbook on satellite communications and broadcasting

    Science.gov (United States)

    Askinazi, G. B.; Bykov, V. L.; Vodopianov, G. V.; D'Iachkova, M. N.; Kantor, L. Ia.; Model, A. M.; Pokras, A. M.; Timofeev, V. V.; Tsirlin, V. M.; Tsirlin, I. S.

    Principles underlying the design and operation of satellite communications systems (SCSs) are reviewed with emphasis on multiple-access techniques. Particular consideration is given to the quality characteristics of CSCs, the frequency ranges assigned to SCSs, an energy analysis of satellite lines, EMC aspects, and the effective utilization of the geostationary orbit. Also examined are the design of earth-station equipment, waveguides and multiplexing equipment, satellite antennas, reliability issues, the Ekran receiving installation, and Gradient-N and Gruppa multiple-access equipment.

  19. Aquatic Equipment Information.

    Science.gov (United States)

    Sova, Ruth

    Equipment usually used in water exercise programs is designed for variety, intensity, and program necessity. This guide discusses aquatic equipment under the following headings: (1) equipment design; (2) equipment principles; (3) precautions and contraindications; (4) population contraindications; and (5) choosing equipment. Equipment is used…

  20. ESA's satellite communications programme

    Science.gov (United States)

    Bartholome, P.

    1985-02-01

    The developmental history, current status, and future plans of the ESA satellite-communications programs are discussed in a general survey and illustrated with network diagrams and maps. Consideration is given to the parallel development of national and European direct-broadcast systems and telecommunications networks, the position of the European space and electronics industries in the growing world market, the impact of technological improvements (both in satellite systems and in ground-based networks), and the technological and commercial advantages of integrated space-terrestrial networks. The needs for a European definition of the precise national and international roles of satellite communications, for maximum speed in implementing such decisions (before the technology becomes obsolete), and for increased cooperation and standardization to assure European equipment manufacturers a reasonable share of the market are stressed.

  1. Satellite Control Laboratory

    DEFF Research Database (Denmark)

    Wisniewski, Rafal; Bak, Thomas

    2001-01-01

    The Satellite Laboratory at the Department of Control Engineering of Aalborg University (SatLab) is a dynamic motion facility designed for analysis and test of micro spacecraft. A unique feature of the laboratory is that it provides a completely gravity-free environment. A test spacecraft...... is suspended on an air bearing, and rotates freely in 3 degrees of freedom. In order to avoid any influence of the gravitational force the centre of mass of the satellite is placed in the geometric centre of the air bearing by an automatic balancing system. The test spacecraft is equipped with a three......-axis magnetometer, three piezoelectric gyros, and four reaction wheels in a tetrahedron configuration. The operation of the spacecraft is fully autonomous. The data flow between the transducers and the onboard computer placed physically outside the satellite is provided by a radio link. The purpose...

  2. System analysis for millimeter-wave communication satellites

    Science.gov (United States)

    Holland, L. D.; Hilsen, N. B.; Gallagher, J. J.; Stevens, G.

    1980-01-01

    Research and development needs for millimeter-wave space communication systems are presented. Assumed propagation fade statistics are investigated along with high data rate diversity link and storage. The development of reliable ferrite switches, and high performance receivers and transmitters is discussed, in addition to improved tolerance of dish and lens fabrication for the antennas. The typical cost for using a simplex voice channel via a high capacity 40/50 GHz satellite is presented.

  3. Radio interferometry and satellite tracking

    CERN Document Server

    Kawase, Seiichiro

    2012-01-01

    Worldwide growth of space communications has caused a rapid increase in the number of satellites operating in geostationary orbits, causing overcrowded orbits. This practical resource is designed to help professionals overcome this problem. This timely book provides a solid understanding of the use of radio interferometers for tracking and monitoring satellites in overcrowded environments. Practitioners learn the fundamentals of radio interferometer hardware, including antennas, receiving equipment, signal processing and phase detection, and measurement accuracies. This in-depth volume describ

  4. Optical analysis and performance evaluation of a solar parabolic dish concentrator

    Directory of Open Access Journals (Sweden)

    Pavlović Saša R.

    2016-01-01

    Full Text Available In this study, the optical design of a solar parabolic dish concentrator is presented. The parabolic dish concentrator consists from 11 curvilinear trapezoidal reflective petals made of polymethyl methacrylate with special reflective coating. The dish diameter is equal to 3.8 m and the theoretical focal point distance is 2.26 m. Numerical simulations are made with the commercial software TracePro from Lambda Research, USA, and the final optimum position between absorber and reflector was calculated to 2.075 m; lower than focus distance. This paper presents results for the optimum position and the optimum diameter of the receiver. The decision for selecting these parameters is based on the calculation of the total flux over the flat and corrugated pipe receiver surface; in its central region and in the peripheral region. The simulation results could be useful reference for designing and optimizing of solar parabolic dish concentrators as for as for CFD analysis, heat transfer and fluid flow analysis in corrugated spiral heat absorbers. [Projekat Ministarstva nauke Republike Srbije, br. III42006: Research and development of energy and environmentally highly effective polygeneration systems based on renewable energy resources i br. III45016: Fabrication and characterization of nanophotonic functional structures in biomedicine and informatics

  5. 9 CFR 381.167 - Other poultry dishes and specialty items.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Other poultry dishes and specialty..., DEPARTMENT OF AGRICULTURE AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION POULTRY PRODUCTS INSPECTION REGULATIONS Definitions...

  6. A small scale cell culture system to analyze mechanobiology using reporter gene constructs and polyurethane dishes

    DEFF Research Database (Denmark)

    Seefried, Lothar; Mueller-Deubert, Sigrid; Wentzer, Thomas Schwarz

    2010-01-01

    of mechanotransduction and its crosstalk with biochemically induced signal transduction, AP1 and SP1 luciferase reporter gene constructs were cloned and transfected into various cell lines and primary cells. A newly developed bioreactor and small-scale 24-well polyurethane dishes were used to apply cyclic stretching...

  7. Stamped Petri dishes for 3D cell culture and drug testing

    NARCIS (Netherlands)

    Sridhar, Adithya; de Boer, Hans L.; van den Berg, Albert; le Gac, Severine

    2013-01-01

    We report here an experimentation platform directly made in a commercially available Petri dish for large-scale production of uniformly sized microtissues and their in situ characterization using both conventional microscopy and a scanning probe technique. The platform is realized by hot embossing m

  8. Modelling dishes and exploring culinary 'precisions': the two issues of molecular gastronomy.

    Science.gov (United States)

    This, Hervé

    2005-04-01

    The scientific strategy of molecular gastronomy includes modelling 'culinary definitions' and experimental explorations of 'culinary precisions'. A formalism that describes complex dispersed systems leads to a physical classification of classical sauces, as well as to the invention of an infinite number of new dishes.

  9. Membrane dish analysis: A summary of structural and optical analysis capabilities

    Energy Technology Data Exchange (ETDEWEB)

    Steele, C.R.; Balch, C.D.; Jorgensen, G.J.; Wendelin, T.; Lewandowski, A.

    1991-11-01

    Research at SERI within the Department of Energy's Solar Thermal Technology Program has focused on the development of membrane dish concentrators for space and terrestrial power applications. As potentially lightweight, inexpensive, high-performance structures, they are excellent candidates for space-deployable energy sources as well as cost-effective terrestrial energy concepts. A thorough engineering research treatment of these types of structures consists primarily of two parts: (1) structural mechanics of the membrane and ring support and (2) analysis and characterization of the concentrator optical performance. It is important to understand the effects of the membrane's structure and support system on the optical performance of the concentrator. This requires an interface between appropriate structural and optical models. Until recently, such models and the required interface have not existed. This report documents research that has been conducted at SERI in this area. It is a compilation of several papers describing structural models of membrane dish structures and optical models used to predict dish concentrator optical and thermal performance. The structural models were developed under SERI subcontract by Dr. Steele and Dr. Balch of Stanford University. The optical model was developed in-house by SERI staff. In addition, the interface between the models is described. It allows easy and thorough characterization of membrane dish systems from the mechanics to the resulting optical performance. The models described herein have been and continue to be extremely useful to SERI, industry, and universities involved with the modeling and analysis of lightweight membrane concentrators for solar thermal applications.

  10. Slope Measurements of Parabolic Dish Concentrators Using Color-Coded Targets

    Energy Technology Data Exchange (ETDEWEB)

    Ulmer, S.; Heller, P.; Reinalter, W.

    2006-07-01

    A new short, yet highly accurate method for measuring the slope errors of parabolic dish concentrators has been developed. This method uses a flat target with colored stripes that is placed close to the focal plane and a digital camera located at an observation point on the optical axis at some distance from it. A specially developed image analysis algorithm detects the different colors in the images of the reflection of the target in the concentrator and assigns them their known position on the color target. This information, along with the geometric relationship between the components of the measurement setup and the theoretical parabolic shape of the concentrator, is used to calculate the normal vectors of the concentrator surface. From these normal vectors the radial and tangential slopes can be calculated and compared to the design values of the concentrator. The resulting slope errors not only give the total concentrator error for general characterization of the dish, but also indicate systematic errors in fabrication and mounting with high spatial resolution. In order to verify the quality of the results obtained, a ray-tracing code was developed that calculates the flux distribution on planes perpendicular to the optical axis. Measured slope errors of a DISTAL-2 dish concentrator are presented and the calculated flux distributions are compared to measured flux distributions. The comparison shows excellent agreement in the flux distribution on the absorber plane. This verifies the promising potential of this method for fast, highly precise measurement of imperfections in dish concentrator shape. (Author)

  11. Nutritional assessment of the most frequently consumed dishes in a slum in Iquitos, Peruvian Amazon

    Directory of Open Access Journals (Sweden)

    Guillermo Molina Recio

    Full Text Available Introduction: Large nutritional surveys in Peru have identified the magnitude and location of the different types of malnutrition. The chronic type is the most prevalent one. However, although rates may be considered as alarming (even more in rural areas, only one of these studies contains information about intake characteristics, using 24-hour recalls (R24. That is, it lacks some other systems, adapted to the gastronomical characteristics of their regions and to the bioavailability of food in each area, in order to locate the origin of this situation and, thus, propose truly effective and efficient solutions. Aim: To determine the nutritional value of the main dishes consumed by the residents of a slum in Peruvian Amazon. Methods: Ninety-eight participants completed three 24-h recalls. Based on these data, we selected the 25 most commonly eaten dishes and evaluated their nutritional composition. We took note of the homemade recipes, weights and measures. In addition, we observed preparation and cooking. The mean nutritional composition of each dish was calculated per 100 g using the Nutriplato 4.6. software. We also calculated gains or losses resulting from culinary treatments. Results: Within those which include milk, the highest energy density is the mingado de arroz. In the group of fish, the most energetic is pescado frito, while within meat-based recipes tallarín con pollo, res asada and chancho frito are the most energetic ones. Regarding prepared dishes, the juane is the highest energy density of all recipes. Inside garnish, using bananas as the main ingredient, plátano frito and madurito are the most energetic. Fats are higher in fried dishes and those which contribute most fat ratio. The same thing happens with garnish as 100 grams of plátano frito or madurito contain more than 70% of the RDA. Res asada and juane present the highest sodium level. Conclusions: If we wish to offer healthier dishes, it is necessary to change their

  12. The Comparison of Photovoltaic with Small Solar Dish Stirling for Solar Home System 50 W{sub p} in Thailand, Medium Insolation Nature

    Energy Technology Data Exchange (ETDEWEB)

    Snidvongs, E. S.; Jindaruj, S.

    2006-07-01

    The Thai government initiated a project entitled Solar Home System which involved the provision of standalone Photovoltaic 50 Wp for houses without transmission lines in remote areas, 300,000 units. These units are provided at a low price with the government supporting half of the cost and the rest paid by the owners in installments. So far, more than 150,000 units have been installed and it is expected that the whole project would be completed by the end of the year 2005. A purpose of this research is to compare the original Thai government's Solar Home PV System with the new 50 Wp Small Solar Thermal Dish Stirling System in terms of their advantages and disadvantages for Thailand. The result of this would serve as a guide for the users to select the most suitable system in terms of price, maintenance, cost, economy, performance, reliability, and efficiency. Such comparison will be presented in the form of descriptive, photographs, statistics, and tables. As for the data involved, part of this is based on active fact such as construction cost, material cost, labor cost, rate of inflation, rate of interest. While some of these derives from the experience of researcher as well as facts and figures from Thai governments publications such as operation and maintenance cost. In addition to that some data are taken from basic experiments conducted either by the various universities and the researcher own laboratory. These include solar insolation, PV data and Stirling engine test with electric heater. And, of course, some data are based on simple estimation and prediction. Thailand is a country of 550 w/m2 with high humidity, soft-land and medium insolation. It locates near the equator at latitude 5 12 N, longitude 96 106 E. By using a parabolic shape satellite dish with solar tracker and a 60 W Four Cylinders gamma type Stirling engine with sinusoidal gear linear link, low offset space, and solid thermal storage to act as buffer between the solar energy and the

  13. Design and Fabrication of a Two Axis Parabolic Solar Dish Collector

    Directory of Open Access Journals (Sweden)

    Prof. Sonal C Yogi

    2014-11-01

    Full Text Available The work consists of the design of the chain drive system and the fabrication of the two axis parabolic solar dish. It is a model study of the two axis parabolic dish which worked by the automatic circuit that was developed. Ready made parabolic solar dish is taken and fabricated. The circular iron ring provides the two axis motion of the dish. A compound chain drive system was developed for the smooth movement of the dish. An electromechanical system which tracks the sun on both axes and which is controlled via a programmable logic control (PLC was designed and implemented. In this a theoretical study was done. A C program was made which gave the required result for the graphical representation of the recorded radiation. Programmable Logic Controls (PLC was used instead of photo sensors, which are widely used for tracking the sun. The azimuthal angle of the sun from sunrise to sunset times was calculated for each day of the year at 23.59 Lat & 72.38Longitude in the Northern hemisphere, the location of the city Mehsana. According to this azimuth angle, the required analog signal was taken from the PLC analog module and sent to the power window motor, which controlled the position of the panel to ensure that the rays fall vertically on the panel. After the mechanical control of the system was started, the performance measurements of the solar panel were carried out. The values obtained from the measurements were compared and the necessary evaluations were conducted.

  14. Satellite RNAs and Satellite Viruses.

    Science.gov (United States)

    Palukaitis, Peter

    2016-03-01

    Satellite RNAs and satellite viruses are extraviral components that can affect either the pathogenicity, the accumulation, or both of their associated viruses while themselves being dependent on the associated viruses as helper viruses for their infection. Most of these satellite RNAs are noncoding RNAs, and in many cases, have been shown to alter the interaction of their helper viruses with their hosts. In only a few cases have the functions of these satellite RNAs in such interactions been studied in detail. In particular, work on the satellite RNAs of Cucumber mosaic virus and Turnip crinkle virus have provided novel insights into RNAs functioning as noncoding RNAs. These effects are described and potential roles for satellite RNAs in the processes involved in symptom intensification or attenuation are discussed. In most cases, models describing these roles involve some aspect of RNA silencing or its suppression, either directly or indirectly involving the particular satellite RNA.

  15. Centriolar satellites

    DEFF Research Database (Denmark)

    Tollenaere, Maxim A X; Mailand, Niels; Bekker-Jensen, Simon

    2015-01-01

    Centriolar satellites are small, microscopically visible granules that cluster around centrosomes. These structures, which contain numerous proteins directly involved in centrosome maintenance, ciliogenesis, and neurogenesis, have traditionally been viewed as vehicles for protein trafficking...... highlight newly discovered regulatory mechanisms targeting centriolar satellites and their functional status, and we discuss how defects in centriolar satellite components are intimately linked to a wide spectrum of human diseases....

  16. Satellite theory

    Science.gov (United States)

    Kozai, Y.

    1981-04-01

    The dynamical characteristics of the natural satellite of Mars, Jupiter, Saturn, Uranus and Neptune are analyzed on the basis of the solar tidal perturbation factor and the oblateness factor of the primary planet for each satellite. For the inner satellites, for which the value of the solar tidal factor is much smaller than the planetary oblateness factor, it is shown that the eccentricity and inclination of satellite orbits are generally very small and almost constant; several pairs of inner satellites are also found to exhibit commensurable mean motions, or secular accelerations in mean longitude. In the case of the outer satellites, for which solar perturbations are dominant, secular perturbations and long-period perturbations may be derived by the solution of equations of motion reduced to one degree of freedom. The existence of a few satellites, termed intermediary satellites, for which the solar tidal perturbation is on the order of the planetary oblateness factor, is also observed, and the pole of the orbital plane of the satellite is noted to execute a complex motion around the pole of the planet or the orbital plane of the planet.

  17. Cultivation-independent comprehensive investigations on bacterial communities in serofluid dish, a traditional Chinese fermented food.

    Science.gov (United States)

    Chen, Peng; Wu, Zhengrong; Zhao, Yang; Wei, Yan; Xu, Ruixiang; Yan, Lei; Li, Hongyu

    2016-03-01

    Serofluid dish (or Jiangshui, in Chinese), a traditional food in the Chinese culture, is made from vegetables by fermentation. In this study, bacterial community of the fermented serofluid dish was assessed by Illumina amplicon sequencing. The metagenome comprised of 49,589 average raw reads with an average 11,497,917 bp and G + C content is 52.46%. This is the first report on V4 hyper-variable region of the 16S rRNA metagenome sequence employing Illumina platform to profile the microbial community of this little known fermented food from Gansu Province, China. The metagenome sequence can be accessed at NCBI, SRA database accession no. SRP065370.

  18. Cultivation-independent comprehensive investigations on bacterial communities in serofluid dish, a traditional Chinese fermented food

    Directory of Open Access Journals (Sweden)

    Peng Chen

    2016-03-01

    Full Text Available Serofluid dish (or Jiangshui, in Chinese, a traditional food in the Chinese culture, is made from vegetables by fermentation. In this study, bacterial community of the fermented serofluid dish was assessed by Illumina amplicon sequencing. The metagenome comprised of 49,589 average raw reads with an average 11,497,917 bp and G+C content is 52.46%. This is the first report on V4 hyper-variable region of the 16S rRNA metagenome sequence employing Illumina platform to profile the microbial community of this little known fermented food from Gansu Province, China. The metagenome sequence can be accessed at NCBI, SRA database accession no. SRP065370.

  19. Acrylamide in a fried potato dish (rösti) from restaurants in Zurich, Switzerland.

    Science.gov (United States)

    McCombie, Gregor; Biedermann, Maurus; Biedermann-Brem, Sandra; Suter, Gaby; Eicher, Angela; Pfefferle, Anton

    2016-01-01

    Rösti, a fried potato product, is a large contributor to acrylamide exposure locally in Switzerland. A survey of 55 dishes prepared by 51 restaurants in the city of Zurich showed that the average rösti contained 702 µg/kg acrylamide. By analysing the content of reducing sugars in the potatoes used for frying, it is shown that with simple measures, the exposure to acrylamide could easily be reduced by factor 2 or more, while even improving the culinary experience. Though rösti is a typical dish in the German-speaking areas in Switzerland, the result may be of general interest for fried potato products which are popular in large areas of Central Europe.

  20. Dish washing detergent market%中国洗洁精市场概况

    Institute of Scientific and Technical Information of China (English)

    谷俊

    2011-01-01

    this paper points out the phenomenon of concentration highly and homogeneity seriously in dish washing detergent market,analyzes factors in the main sale channels,approach as well as influence for consumers purchase.Finally,it introduces the strategy in dish washing detergent market.%探讨了洗洁精市场集中度高和同质化严重的现象。分析了主要销售渠道、销售手段以及影响消费者购买洗洁精的因素。最后,介绍了洗洁精行业的市场竞争战略。

  1. Optical design and optimization of parabolic dish solar concentrator with a cavity hybrid receiver

    Science.gov (United States)

    Blázquez, R.; Carballo, J.; Silva, M.

    2016-05-01

    One of the main goals of the BIOSTIRLING-4SKA project, funded by the European Commission, is the development of a hybrid Dish-Stirling system based on a hybrid solar-gas receiver, which has been designed by the Swedish company Cleanergy. A ray tracing study, which is part of the design of this parabolic dish system, is presented in this paper. The study pursues the optimization of the concentrator and receiver cavity geometry according to the requirements of flux distribution on the receiver walls set by the designer of the hybrid receiver. The ray-tracing analysis has been performed with the open source software Tonatiuh, a ray-tracing tool specifically oriented to the modeling of solar concentrators.

  2. Membrane dish analysis: A summary of structural and optical analysis capabilities

    Energy Technology Data Exchange (ETDEWEB)

    Steele, C.R.; Balch, C.D.; Jorgensen, G.J.; Wendelin, T.; Lewandowski, A.

    1991-11-01

    Research at SERI within the Department of Energy`s Solar Thermal Technology Program has focused on the development of membrane dish concentrators for space and terrestrial power applications. As potentially lightweight, inexpensive, high-performance structures, they are excellent candidates for space-deployable energy sources as well as cost-effective terrestrial energy concepts. A thorough engineering research treatment of these types of structures consists primarily of two parts: (1) structural mechanics of the membrane and ring support and (2) analysis and characterization of the concentrator optical performance. It is important to understand the effects of the membrane`s structure and support system on the optical performance of the concentrator. This requires an interface between appropriate structural and optical models. Until recently, such models and the required interface have not existed. This report documents research that has been conducted at SERI in this area. It is a compilation of several papers describing structural models of membrane dish structures and optical models used to predict dish concentrator optical and thermal performance. The structural models were developed under SERI subcontract by Dr. Steele and Dr. Balch of Stanford University. The optical model was developed in-house by SERI staff. In addition, the interface between the models is described. It allows easy and thorough characterization of membrane dish systems from the mechanics to the resulting optical performance. The models described herein have been and continue to be extremely useful to SERI, industry, and universities involved with the modeling and analysis of lightweight membrane concentrators for solar thermal applications.

  3. Modeling the small-scale dish-mounted solar thermal Brayton cycle

    Science.gov (United States)

    Le Roux, Willem G.; Meyer, Josua P.

    2016-05-01

    The small-scale dish-mounted solar thermal Brayton cycle (STBC) makes use of a sun-tracking dish reflector, solar receiver, recuperator and micro-turbine to generate power in the range of 1-20 kW. The modeling of such a system, using a turbocharger as micro-turbine, is required so that optimisation and further development of an experimental setup can be done. As a validation, an analytical model of the small-scale STBC in Matlab, where the net power output is determined from an exergy analysis, is compared with Flownex, an integrated systems CFD code. A 4.8 m diameter parabolic dish with open-cavity tubular receiver and plate-type counterflow recuperator is considered, based on previous work. A dish optical error of 10 mrad, a tracking error of 1° and a receiver aperture area of 0.25 m × 0.25 m are considered. Since the recuperator operates at a very high average temperature, the recuperator is modeled using an updated ɛ-NTU method which takes heat loss to the environment into consideration. Compressor and turbine maps from standard off-the-shelf Garrett turbochargers are used. The results show that for the calculation of the steady-state temperatures and pressures, there is good comparison between the Matlab and Flownex results (within 8%) except for the recuperator outlet temperature, which is due to the use of different ɛ-NTU methods. With the use of Matlab and Flownex, it is shown that the small-scale open STBC with an existing off-the-shelf turbocharger could generate a positive net power output with solar-to-mechanical efficiency of up to 12%, with much room for improvement.

  4. AIPS++ and the GBT: a layered approach to processing and analysis of single-dish data

    Science.gov (United States)

    Braatz, James; McMullin, Joseph; Garwood, Robert; Kemball, Athol

    2002-12-01

    The Green Bank Telescope (GBT) is a new 100-m diameter antenna with an unblocked aperture and an active surface. It is designed to observe at frequencies from 300 MHz to 100 GHz, and includes state of the art continuum and spectral backends. The GBT is also capable of pulsar work and recording as a VLB station, and array receivers are being developed as well. AIPS++ is the integral software package for analysis of GBT data both for scientific analysis as well as for control and engineering analysis of the component systems. In this paper we will give an overview of how the AIPS++ system is used with the GBT, with special consideration to the development of spectral analysis software. AIPS++ allows a layered approach to software development, and the spectral analysis capability gives a strong example of the usefulness of the layered approach. At the heart of AIPS++ is a suite of tools which are capable of astronomy-specific calculations as well as general purpose mathematical analysis, data visualization, GUI development, and scripting. A tool for analyzing single-dish data, DISH, is developed on this platform. DISH includes a number of modern features such as bulk processing of datasets and versatile GUI interaction. A simplified package using a familiar CLI, known as UNI-jr, is built on DISH and is available as an easy to learn path for processing scan-based data. Finally, the Interim Automated Reduction and Display System (IARDS) is built on UNI-jr and provides an automated reduction package and pseudo real-time display.

  5. Pork in good company? Exploratory analysis of side dishes, beverages, foodscapes and individual characteristics.

    Science.gov (United States)

    Verbeke, Wim; Perez-Cueto, Federico J A; de Barcellos, Marcia Dutra; Grunert, Klaus G

    2013-11-01

    The objective of this study is to explore the association between pork as the main meal component and the choice for side dishes and beverages depending on foodscape and individual characteristics, including overweight and obesity among fresh pork consumers (n=2156) in five European countries (Belgium, Denmark, Germany, Greece and Poland). Males were found to combine pork more with caloric drinking (odds ratio=1.32) and low levels of vegetable intake (odds ratio=1.32) compared to females. Younger consumers were more likely to combine pork with low levels of vegetable intake but less likely to combine pork with sauces or condiments. Heavy users of pork were more likely (odds ratio=1.43) to combine pork with sauces or condiments. The study also found an association between being overweight or obese and higher consumption of carbohydrate rich staple foods (odds ratio=1.30) and caloric drinks (odds ratio=1.30) as side dishes to pork meat. Substantial cross-cultural differences were revealed in line with typical pork consumption and meal composition habits in the respective countries. Finally, this study found that the company of family plays a significant role when choosing side dishes for pork as meal center, thus constituting a relevant venue for the positioning and marketing of pork, as well as for future public health information about meals with pork as main meal component.

  6. Primary Beam and Dish Surface Characterization at the Allen Telescope Array by Radio Holography

    CERN Document Server

    Atkinson, Shannon; Backus, P R; Barott, William; Bauermeister, Amber; Blitz, Leo; Bock, D C -J; Bower, Geoffrey C; Bradford, Tucker; Cheng, Calvin; Croft, Steve; Dexter, Matt; Dreher, John; Engargiola, Greg; Fields, Ed; Heiles, Carl; Helfer, Tamara; Jordan, Jane; Jorgensen, Susan; Kilsdonk, Tom; Gutierrez-Kraybill, Colby; Keating, Garrett; Law, Casey; Lugten, John; MacMahon, D H E; McMahon, Peter; Milgrome, Oren; Siemion, Andrew; Smolek, Ken; Thornton, Douglas; Pierson, Tom; Randall, Karen; Ross, John; Shostak, Seth; Tarter, J C; Urry, Lynn; Werthimer, Dan; Williams, Peter K G; Whysong, David; Harp, G R; Ackermann, R F; Nadler, Z J; Blair, Samantha K; Davis, M M; Wright, M C H; Forster, J R; DeBoer, D R; Welch, W J

    2012-01-01

    The Allen Telescope Array (ATA) is a cm-wave interferometer in California, comprising 42 antenna elements with 6-m diameter dishes. We characterize the antenna optical accuracy using two-antenna interferometry and radio holography. The distortion of each telescope relative to the average is small, with RMS differences of 1 percent of beam peak value. Holography provides images of dish illumination pattern, allowing characterization of as-built mirror surfaces. The ATA dishes can experience mm-scale distortions across -2 meter lengths due to mounting stresses or solar radiation. Experimental RMS errors are 0.7 mm at night and 3 mm under worst case solar illumination. For frequencies 4, 10, and 15 GHz, the nighttime values indicate sensitivity losses of 1, 10 and 20 percent, respectively. The ATA.s exceptional wide-bandwidth permits observations over a continuous range 0.5 to 11.2 GHz, and future retrofits may increase this range to 15 GHz. Beam patterns show a slowly varying focus frequency dependence. We prob...

  7. Finite time thermodynamic analysis and optimization of solar-dish Stirling heat engine with regenerative losses

    Directory of Open Access Journals (Sweden)

    Sharma Arjun

    2011-01-01

    Full Text Available The present study investigates the performance of the solar-driven Stirling engine system to maximize the power output and thermal efficiency using the non-linearized heat loss model of the solar dish collector and the irreversible cycle model of the Stirling engine. Finite time thermodynamic analysis has been done for combined system to calculate the finite-rate heat transfer, internal heat losses in the regenerator, conductive thermal bridging losses and finite regeneration process time. The results indicate that exergy efficiency of dish system increases as the effectiveness of regenerator increases but decreases with increase in regenerative time coefficient. It is also found that optimal range of collector temperature and corresponding concentrating ratio are 1000 K~1400 K and 1100~1400, respectively in order to get maximum value of exergy efficiency. It is reported that the exergy efficiency of this dish system can reach the maximum value when operating temperature and concentrating ratio are 1150 K and 1300, respectively.

  8. Method of manufacturing large dish reflectors for a solar concentrator apparatus

    Science.gov (United States)

    Angel, Roger P; Olbert, Blain H

    2011-12-27

    A method of manufacturing monolithic glass reflectors for concentrating sunlight in a solar energy system is disclosed. The method of manufacturing allows large monolithic glass reflectors to be made from float glass in order to realize significant cost savings on the total system cost for a solar energy system. The method of manufacture includes steps of heating a sheet of float glass positioned over a concave mold until the sheet of glass sags and stretches to conform to the shape of the mold. The edges of the dish-shaped glass are rolled for structural stiffening around the periphery. The dish-shaped glass is then silvered to create a dish-shaped mirror that reflects solar radiation to a focus. The surface of the mold that contacts the float glass preferably has a grooved surface profile comprising a plurality of cusps and concave valleys. This grooved profile minimizes the contact area and marring of the specular glass surface, reduces parasitic heat transfer into the mold and increases mold lifetime. The disclosed method of manufacture is capable of high production rates sufficiently fast to accommodate the output of a conventional float glass production line so that monolithic glass reflectors can be produced as quickly as a float glass production can make sheets of float glass to be used in the process.

  9. Nano Petri dishes: a new polystyrene platform for studying cell-nanoengineered surface interactions

    Science.gov (United States)

    Cha, Kyoung Je; Na, Moon-Hee; Kim, Hyung Woo; Kim, Dong Sung

    2014-05-01

    In this study, we fabricated and fully characterized a new type of polystyrene (PS) cell-culture platform containing nanoengineered surfaces (NES), referred to as a nano Petri dish, which can be used at the transition stage of basic cell-NES interaction studies for clinical applications. Nano-injection molding in this study was used for the mass production of the nano Petri dish having nanopore arrays. The effects of processing parameters of the injection molding on the replication quality of the nanopore arrays were quantitatively evaluated by means of design of experiments based on the Taguchi method. This allowed efficient and reliable cell culture studies by providing large numbers of the same dishes, in addition to removing the fixation step of the NES plates inside the cell-culture container. Physical, chemical and mechanical properties of the NES, as well as cell behavior including attachment and proliferation of human osteosarcoma MG-63 cells on the NES, were then characterized, with and without the oxygen plasma surface treatment.

  10. An Axi-Symmetric Segmented Composite SKA Dish Design: Performance and Production Analysis

    CERN Document Server

    Ivashina, M V; de Vaate, J G bij; Iupikov, O A; Arts, M; Dekker, J; van Ardenne, A

    2011-01-01

    A concept of an axi-symmetric dish as antenna reflector for the next generation radio telescope - the Square Kilometre Array (SKA) - is presented. The reflector is based on the use of novel thermoplastic composite material (reinforced with carbon fibre) in the context of the telescope design with wide band single pixel feeds. The baseline of this design represents an array of 100's to 1000's reflector antennas of 15-m diameter and covers frequencies from <1 to 10 GHz. The purpose of our study is the analysis of the production cost of the dish and its performance in combination with a realistic wideband feed (such as the 'Eleven Antenna' feed) over a wide frequency band and a range of elevation angles. The presented initial simulation results inidicate the potential of the proposed dish concept for low-cost and mass production and demonstrate sensitivity comparable to that of the presently considered off-set Gregorian reflector antenna with the same projected aperture area. We expect this observation to be ...

  11. The Hydrogen Epoch of Reionization Array Dish I: Beam Pattern Measurements and Science Implications

    CERN Document Server

    Neben, Abraham R; Hewitt, Jacqueline N; DeBoer, David R; Parsons, Aaron R; Aguirre, James E; Ali, Zaki S; Cheng, Carina; Ewall-Wice, Aaron; Patra, Nipanjana; Thyagarajan, Nithyanandan; Bowman, Judd; Dickenson, Roger; Dillon, Joshua S; Doolittle, Phillip; Egan, Dennis; Hedrick, Mike; Jacobs, Daniel C; Kohn, Saul A; Klima, Patricia J; Moodley, Kavilan; Saliwanchik, Benjamin R B; Schaffner, Patrick; Shelton, John; Taylor, H A; Taylor, Rusty; Tegmark, Max; Wirt, Butch; Zheng, Haoxuan

    2016-01-01

    The Hydrogen Epoch of Reionization Array (HERA) is a radio interferometer aiming to detect the power spectrum of 21cm fluctuations from neutral hydrogen from the Epoch of Reionization (EOR). Drawing on lessons from the Murchison Widefield Array (MWA) and the Precision Array for Probing the Epoch of Reionization (PAPER), HERA is a hexagonal array of large (14m diameter) dishes with suspended dipole feeds. Not only does the dish determine overall sensitivity, it affects the observed frequency structure of foregrounds in the interferometer. This is the first of a series of four papers characterizing the frequency and angular response of the dish with simulations and measurements. We focus in this paper on the angular response (i.e., power pattern), which sets the relative weighting between sky regions of high and low delay, and thus, apparent source frequency structure. We measure the angular response at 137MHz using the ORBCOMM beam mapping system of Neben et al. We measure a collecting area of 93m^2 in the opt...

  12. 液化天然气(LNG)卫星站设备选型分析%Analysis on Type Selection of Equipments for Satellite Stations of Liquefied Natural Gas

    Institute of Scientific and Technical Information of China (English)

    苏圣钧

    2015-01-01

    The main role of LNG satellite station is storage, gasification and liquefaction of natural gas, and transports natural gas to downstream users. In this paper, the composition and working principle of the main system in LNG satellite station were introduced; type selection of LNG tanker, LNG storage tanks, air temperature vaporizer and the water bath heater was analyzed. At last, the rationality of type selection was verified by an example.%LNG 卫星站主要作用为储存、气化液化天然气,并将气化后的气态天然气输送给下游用户。简单介绍了 LNG 卫星站主要系统组成及其工作原理,对卫星站主要设备 LNG 槽车、LNG 储罐、空温气化器和水浴加热器进行了选型分析,最后通过实例进行验证选型。

  13. Geosynchronous Earth Orbit/Low Earth Orbit Space Object Inspection and Debris Disposal: A Preliminary Analysis Using a Carrier Satellite With Deployable Small Satellites

    OpenAIRE

    Crockett, Derick A.

    2013-01-01

    Detailed observations of geosynchronous satellites from earth are very limited. To better inspect these high altitude satellites, the use of small, refuelable satellites is proposed. The small satellites are stationed on a carrier platform in an orbit near the population of geosynchronous satellites. A carrier platform equipped with deployable, refuelable SmallSats is a viable option to inspect geosynchronous satellites. The propellant requirement to transfer to a targeted geosynchronous sate...

  14. 14 CFR 142.17 - Satellite training centers.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Satellite training centers. 142.17 Section...) SCHOOLS AND OTHER CERTIFICATED AGENCIES TRAINING CENTERS General § 142.17 Satellite training centers. (a... training program at a satellite training center if— (1) The facilities, equipment, personnel, and...

  15. Inexpensive land-use maps extracted from satellite data

    Science.gov (United States)

    Barney, T. W.; Barr, D. J.; Elifrits, C. D.; Johannsen, C. J.

    1979-01-01

    Satellite images are interpretable with minimal skill and equipment by employing method which uses false color composite print of image of area transmitted from Landsat satellite. Method is effective for those who have little experience with satellite imagery, little time, and little money available.

  16. Equipment. Out of order.

    Science.gov (United States)

    Connolly, C

    2000-08-17

    The NHS has underinvested in equipment for more than 20 years. Most hospitals have inadequate equipment inventories. More than half the anaesthetic machines in use are more than five years old and should be replaced. Almost a fifth of the equipment used in cancer treatment is obsolete. Current accounting systems act as a disincentive to replacing old equipment.

  17. Experimental Satellite Quantum Communications.

    Science.gov (United States)

    Vallone, Giuseppe; Bacco, Davide; Dequal, Daniele; Gaiarin, Simone; Luceri, Vincenza; Bianco, Giuseppe; Villoresi, Paolo

    2015-07-24

    Quantum communication (QC), namely, the faithful transmission of generic quantum states, is a key ingredient of quantum information science. Here we demonstrate QC with polarization encoding from space to ground by exploiting satellite corner cube retroreflectors as quantum transmitters in orbit and the Matera Laser Ranging Observatory of the Italian Space Agency in Matera, Italy, as a quantum receiver. The quantum bit error ratio (QBER) has been kept steadily low to a level suitable for several quantum information protocols, as the violation of Bell inequalities or quantum key distribution (QKD). Indeed, by taking data from different satellites, we demonstrate an average value of QBER=4.6% for a total link duration of 85 s. The mean photon number per pulse μ_{sat} leaving the satellites was estimated to be of the order of one. In addition, we propose a fully operational satellite QKD system by exploiting our communication scheme with orbiting retroreflectors equipped with a modulator, a very compact payload. Our scheme paves the way toward the implementation of a QC worldwide network leveraging existing receivers.

  18. Ocean surveillance satellites

    Science.gov (United States)

    Laurent, D.

    Soviet and U.S. programs involving satellites for surveillance of ships and submarines are discussed, considering differences in approaches. The Soviet program began with the Cosmos 198 in 1967 and the latest, the Cosmos 1400 series, 15 m long and weighing 5 tons, carry radar for monitoring ships and a nuclear reactor for a power supply. Other Soviet spacecraft carrying passive microwave sensors and ion drives powered by solar panels have recently been detonated in orbit for unknown reasons. It has also been observed that the Soviet satellites are controlled in pairs, with sequential orbital changes for one following the other, and both satellites then overflying the same points. In contrast, U.S. surveillance satellites have been placed in higher orbits, thus placing greater demands on the capabilities of the on-board radar and camera systems. Project White Cloud and the Clipper Bow program are described, noting the continued operation of the White Cloud spacecraft, which are equipped to intercept radio signals from surface ships. Currently, the integrated tactical surveillance system program has completed its study and a decision is expected soon.

  19. Satellite Control Laboratory

    DEFF Research Database (Denmark)

    Wisniewski, Rafal; Bak, Thomas

    2001-01-01

    The Satellite Laboratory at the Department of Control Engineering of Aalborg University (SatLab) is a dynamic motion facility designed for analysis and test of micro spacecraft. A unique feature of the laboratory is that it provides a completely gravity-free environment. A test spacecraft...... is suspended on an air bearing, and rotates freely in 3 degrees of freedom. In order to avoid any influence of the gravitational force the centre of mass of the satellite is placed in the geometric centre of the air bearing by an automatic balancing system. The test spacecraft is equipped with a three...... of the laboratory is to conduct dynamic tests of the control and attitude determination algorithms during nominal operation and in abnormal conditions. Further it is intended to use SatLab for validation of various algorithms for fault detection, accommodation and supervisory control. Different mission objectives...

  20. Cabbage Dish

    Institute of Scientific and Technical Information of China (English)

    1994-01-01

    Ingredients: 500 grams of cabbage, 40 grams of winter bamboo shoots, 40 grams of rehydrated winter mushrooms, 20 grams of green pepper, 20 grams of red pepper, 30 grams of scallions, 10 grams of ginger, 20-40 grams of chili pepper, 50 grams of salt, 50

  1. Satellite Communications

    CERN Document Server

    Pelton, Joseph N

    2012-01-01

    The field of satellite communications represents the world's largest space industry. Those who are interested in space need to understand the fundamentals of satellite communications, its technology, operation, business, economic, and regulatory aspects. This book explains all this along with key insights into the field's future growth trends and current strategic challenges. Fundamentals of Satellite Communications is a concise book that gives all of the key facts and figures as well as a strategic view of where this dynamic industry is going. Author Joseph N. Pelton, PhD, former Dean of the International Space University and former Director of Strategic Policy at Intelstat, presents a r

  2. Secure voice for mobile satellite applications

    Science.gov (United States)

    Vaisnys, Arvydas; Berner, Jeff

    The initial system studies are described which were performed at JPL on secure voice for mobile satellite applications. Some options are examined for adapting existing Secure Telephone Unit III (STU-III) secure telephone equipment for use over a digital mobile satellite link, as well as for the evolution of a dedicated secure voice mobile earth terminal (MET). The work has included some lab and field testing of prototype equipment. The work is part of an ongoing study at JPL for the National Communications System (NCS) on the use of mobile satellites for emergency communications. The purpose of the overall task is to identify and enable the technologies which will allow the NCS to use mobile satellite services for its National Security Emergency Preparedness (NSEP) communications needs. Various other government agencies will also contribute to a mobile satellite user base, and for some of these, secure communications will be an essential feature.

  3. Secure voice for mobile satellite applications

    Science.gov (United States)

    Vaisnys, Arvydas; Berner, Jeff

    1990-01-01

    The initial system studies are described which were performed at JPL on secure voice for mobile satellite applications. Some options are examined for adapting existing Secure Telephone Unit III (STU-III) secure telephone equipment for use over a digital mobile satellite link, as well as for the evolution of a dedicated secure voice mobile earth terminal (MET). The work has included some lab and field testing of prototype equipment. The work is part of an ongoing study at JPL for the National Communications System (NCS) on the use of mobile satellites for emergency communications. The purpose of the overall task is to identify and enable the technologies which will allow the NCS to use mobile satellite services for its National Security Emergency Preparedness (NSEP) communications needs. Various other government agencies will also contribute to a mobile satellite user base, and for some of these, secure communications will be an essential feature.

  4. Satellite Geomagnetism

    DEFF Research Database (Denmark)

    Olsen, Nils; Stolle, Claudia

    2012-01-01

    Observations of Earth’s magnetic field from space began more than 50 years ago. A continuous monitoring of the field using low Earth orbit (LEO) satellites, however, started only in 1999, and three satellites have taken highprecision measurements of the geomagnetic field during the past decade...... ability to characterize and understand the many sources that contribute to Earth’s magnetic field. In this review, we summarize investigations of Earth’s interior and environment that have been possible through the analysis of high-precision magnetic field observations taken by LEO satellites........ The unprecedented time-space coverage of their data opened revolutionary new possibilities for monitoring, understanding, and exploring Earth’s magnetic field. In the near future, the three-satellite constellation Swarm will ensure continuity of such measurement and provide enhanced possibilities to improve our...

  5. Satellite (Natural)

    Science.gov (United States)

    Murdin, P.

    2000-11-01

    In its most general sense, any celestial object in orbit around a similar larger object. Thus, for example, the Magellanic Clouds are satellite galaxies of our own Milky Way galaxy. Without qualification, the term is used to mean a body in orbit around a planet; an alternative term is moon. The term natural satellite distinguishes these bodies from artificial satellites—spacecraft placed in orbi...

  6. Integration of mobile satellite and cellular systems

    Science.gov (United States)

    Drucker, Elliott H.; Estabrook, Polly; Pinck, Deborah; Ekroot, Laura

    1993-01-01

    By integrating the ground based infrastructure component of a mobile satellite system with the infrastructure systems of terrestrial 800 MHz cellular service providers, a seamless network of universal coverage can be established. Users equipped for both cellular and satellite service can take advantage of a number of features made possible by such integration, including seamless handoff and universal roaming. To provide maximum benefit at lowest posible cost, the means by which these systems are integrated must be carefully considered. Mobile satellite hub stations must be configured to efficiently interface with cellular Mobile Telephone Switching Offices (MTSO's), and cost effective mobile units that provide both cellular and satellite capability must be developed.

  7. The design of the local monitor and control system of SKA dishes

    Science.gov (United States)

    Schillirò, F.; Baldini, V.; Becciani, U.; Cirami, R.; Costa, A.; Ingallinera, A.; Marassi, A.; Nicotra, G.; Nocita, C.; Riggi, S.; Trigilio, C.

    2016-08-01

    The Square Kilometer Array (SKA) project aims at building the world's largest radio observatory to observe the sky with unprecedented sensitivity and collecting area. In the first phase of the project (SKA1), an array of dishes, SKA1-MID, will be built in South Africa. It will consist of 133 15m-dishes, which will include the MeerKAT array, for the 0.350-20 GHz frequency band observations. Each antenna will be provided with a local monitor and control system (LMC), enabling operations both to the Telescope Manager remote system, and to the engineers and maintenance staff; it provides different environment for the telescope control (positioning, pointing, observational bands), metadata collection for monitoring and database storaging, operational modes and functional states management for all the telescope capabilities. In this paper we present the LMC software architecture designed for the detailed design phase (DD), where we describe functional and physical interfaces with monitored and controlled sub-elements, and highlight the data flow between each LMC modules and its sub-element controllers from one side, and Telescope Manager on the other side. We also describe the complete Product Breakdown Structure (PBS) created in order to optimize resources allocation in terms of calculus and memory, able to perform required task for each element according to the proper requirements. Among them, time response and system reliability are the most important, considering the complexity of SKA dish network and its isolated placement. Performances obtained by software implementation using TANGO framework will be discussed, matching them with technical requirements derived by SKA science drivers.

  8. Facet development for a faceted stretched-membrane dish by Solar Kinetics, Inc

    Energy Technology Data Exchange (ETDEWEB)

    Schertz, P.T.; Brown, D.C.; Konnerth, A. III (Solar Kinetics, Inc., Dallas, TX (United States))

    1991-07-01

    A 3.6-meter diameter stretched-membrane optical facet for a parabolic dish has been successfully designed and demonstrated under contract with Sandia National Laboratories. Twelve facets identical to them will be used to make the lightweight reflector of the dish. The project goal of 2.5-mrad surface accuracy was met with each of the two full-sized prototypes, and accuracies of as low as 1.1 mrad were achieved. The facet weight is 11.7 kg/m{sup 2} (2.4lbs/ft{sup 2}). The facet is similar in construction to the successful stretched-membrane heliostat; it has two thin metal membranes attached to a ring. However, the front membrane for this facet is plastically formed at the factor in order to achieve a shorter facet f/D (approximately 3.0). A passive tether restrains the from membrane when not in operation, that is, when the stabilizing vacuum is off. The optical surface is achieved with a silvered-acrylic film laminated to the metal membrane. The facet is expected to cost $55.40/m{sup 2} at a production rate of 10,000 facets per year and $115, 000/m{sup 2}-at a production rate of 500 facets a year. Several key issues have been resolved. Stress concentrations due to seams in the reflective laminate did not cause membrane rupture during forming as they have for dishes with lower focal length-to-diameter ratios. The laminate survived the forming process and simulated operation without deterioration. The optical effect of the tether on the membrane was tested and found to be very small. Most important, highly accurate shapes were obtained using a simple forming procedure. Additional tests are needed to demonstrate process repeatablility and facet performance in typical operating conditions. 18 refs., 36 figs., 11 tabs.

  9. Facet development for a faceted stretched-membrane dish by Solar Kinetics, Inc.

    Science.gov (United States)

    Schertz, P. T.; Brown, D. C.; Konnerth, A., III

    1991-07-01

    A 3.6-meter diameter stretched-membrane optical facet for a parabolic dish has been successfully designed and demonstrated under contract with Sandia National Laboratories. Twelve facets identical to them will be used to make the lightweight reflector of the dish. The project goal of 2.5-mrad surface accuracy was met with each of the two full-sized prototypes, and accuracies of as low as 1.1 mrad were achieved. The facet weight is 11.7 kg/sq m (2.4 lbs/sq ft). The facet is similar in construction to the successful stretched-membrane heliostat; it has two thin metal membranes attached to a ring. However, the front membrane for this facet is plastically formed at the factor in order to achieve a shorter facet f/D (approximately 3.0). A passive tether restrains the front membrane when not in operation, that is, when the stabilizing vacuum is off. The optical surface is achieved with a silvered-acrylic film laminated to the metal membrane. The facet is expected to cost $55.40/sq m at a production rate of 10,000 facets per year and $115,000/sq m at a production rate of 500 facets a year. Several key issues have been resolved. Stress concentrations due to seams in the reflective laminate did not cause membrane rupture during forming as they have for dishes with lower focal length-to-diameter ratios. The laminate survived the forming process and simulated operation without deterioration. The optical effect of the tether on the membrane was tested and found to be very small. Most important, highly accurate shapes were obtained using a simple forming procedure. Additional tests are needed to demonstrate process repeatability and facet performance in typical operating conditions.

  10. The kinematic Stirling engine as an energy conversion subsystem for paraboloidal dish solar thermal plants

    Science.gov (United States)

    Bowyer, J. M.

    1984-01-01

    The potential of a suitably designed and economically manufactured Stirling engine as the energy conversion subsystem of a paraboloidal dish-Stirling solar thermal power module was estimated. Results obtained by elementary cycle analyses were shown to match quite well the performance characteristics of an advanced kinematic Stirling engine, the United Stirling P-40, as established by current prototypes of the engine and by a more sophisticated analytic model of its advanced derivative. In addition to performance, brief consideration was given to other Stirling engine criteria such as durability, reliability, and serviceability. Production costs were not considered here.

  11. Using microdispensing to manufacture a customized cell dish for microbeam irradiation of single, living cells

    Energy Technology Data Exchange (ETDEWEB)

    Nilsson, E.J.C. [Division of Nuclear Physics, Department of Physics, Lund Institute of Technology, Lund University, Box 118, S-22100 Lund (Sweden)], E-mail: charlotta.nilsson@nuclear.lu.se; Olsson, M.G. [Division of Infection Medicine, Department of Clinical Sciences, Lund University, S-22184 Lund (Sweden); Nilsson, J. [Department of Electrical Measurements and Industrial Electrical Engineering and Automation, Lund Institute of Technology, Lund University, Box 118, S-22100 Lund (Sweden); Pallon, J.; Masternak, A. [Division of Nuclear Physics, Department of Physics, Lund Institute of Technology, Lund University, Box 118, S-22100 Lund (Sweden); Paczesny, J. [Division of Nuclear Physics, Department of Physics, Lund Institute of Technology, Lund University, Box 118, S-22100 Lund (Sweden); Division of Infection Medicine, Department of Clinical Sciences, Lund University, S-22184 Lund (Sweden); Arteaga-Marrero, N.; Elfman, M.; Kristiansson, P.; Nilsson, C. [Division of Nuclear Physics, Department of Physics, Lund Institute of Technology, Lund University, Box 118, S-22100 Lund (Sweden); Akerstroem, B. [Division of Infection Medicine, Department of Clinical Sciences, Lund University, S-22184 Lund (Sweden)

    2009-04-15

    In this paper is described the preparation of patterned cell dishes to be used in studies of low dose irradiation effects on living cells. Using a droplet microdispenser, an 8 {mu}m thick polypropylene cell substrate, to which cells do not naturally adhere, was coated in a matrix pattern with the cell adhesive mussel protein Cell-Tak. Cells were shown to adhere and grow on the protein-coated spots, but not on the uncoated parts, providing for guided cell growth. Cultivation of isolated cell colonies provides an opportunity to study how low doses of ionizing radiation affect neighbouring un-irradiated cell colonies.

  12. Immobilization of sericin molecules via amorphous carbon plasma modified-polystyrene dish for serum-free culture

    Energy Technology Data Exchange (ETDEWEB)

    Tunma, Somruthai [The Graduate School, Chiang Mai University, 239 Huay Kaew Road, Muang District, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics (ThEP), 239 Huay Kaew Road, Muang District, Chiang Mai 50200 (Thailand); Song, Doo-Hoon [Research Center for Orofacial Hard Tissue Regeneration, College of Dentistry, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-752 (Korea, Republic of); Kim, Si-Eun; Kim, Kyoung-Nam [Research Center for Orofacial Hard Tissue Regeneration, College of Dentistry, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-752 (Korea, Republic of); Department and Research Institute of Dental Biomaterials and Bioengineering, College of Dentistry, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul 120-752 (Korea, Republic of); Han, Jeon-Geon [Center for Advanced Plasma Surface Technology, Sungkyunkwan University, 300 Chunchun-dong, Jangan-gu, Suwon 440-746 (Korea, Republic of); Boonyawan, Dheerawan, E-mail: dheerawan.b@cmu.ac.th [Thailand Center of Excellence in Physics (ThEP), 239 Huay Kaew Road, Muang District, Chiang Mai 50200 (Thailand); Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, 239 Huay Kaew Road, Muang District, Chiang Mai 50200 (Thailand)

    2013-10-15

    In this study, we focused on sericin hydrolysates, originating from silkworm used in serum-free human bone marrow-derived mesenchymal stem cells (hBM-MSCs) culture. We reported the effect of a covalent linkage between a bioactive protein molecule and polystyrene dish surface via a carbon intermediate layer which can slow down the release rate of protein compounds into the phosphate buffer saline (PBS) solution. Films of amorphous carbon (a-C) and functionalized-carbon were deposited on PS culture dish surfaces by using a DC magnetron sputtering system and RF PECVD system. We found that a-C based-films can increase the hydrophilicity and biocompatibility of polystyrene (PS) dishes, especially a-C films and a-C:N{sub 2} films showed good attachment of hBM-MSCs at 24 h. However, in the case of silica surface (a-C:SiO{sub x} films), the cells showed a ragged and unattached boundary resulting from the presence of surface silanol groups. For the UV–vis absorbance, all carbon modified-PS dishes showed a lower release rate of sericin molecules into PBS solution than PS control. This revealed that the functionalized carbon could be enhanced by specific binding properties with given molecules. The carbon-coated PS dishes grafting with sericin protein were used in a serum-free condition. We also found that hBM-MSCs have higher percentage of proliferated cells at day 7 for the modified dishes with carbon films and coated with sericin than the PS control coated with sericin. The physical film properties were measured by atomic force microscopy (AFM), scanning electron microscope (SEM) and contact angle measurement. The presence of -NH{sub 2} groups of sericin compounds on the PS dish was revealed by Fourier transform infrared spectroscopy (FTIR). The stability of covalent bonds of sericin molecules after washing out ungrafted sericin was confirmed by X-ray photoelectron spectroscopy (XPS).

  13. Common NICU Equipment

    Science.gov (United States)

    ... newborn intensive care unit (NICU) > Common NICU equipment Common NICU equipment E-mail to a friend Please ... Baby Caring for your baby Feeding your baby Common illnesses Family health & safety Complications & Loss Pregnancy complications ...

  14. Scientific Satellites

    Science.gov (United States)

    1967-01-01

    followed Hale’s into orbit. In 1879, Jules Verne wrote about launching small satellites with a gun possessing a muzzle velocity of 10 000 m/sec (ref. 3...was activated in 1950.11 It was located only a few tens of miles from the spot where Jules Verne had his Baltimore Gun Club fire a manned projectile to...principle, satellites can be launched by a single impulse applied at the Earth’s surface-say, with a large cannon, & la Jules Verne (sec. 8-3). In

  15. Validation of a Dish-Based Semiquantitative Food Questionnaire in Rural Bangladesh

    Directory of Open Access Journals (Sweden)

    Pi-I. D. Lin

    2017-01-01

    Full Text Available A locally validated tool was needed to evaluate long-term dietary intake in rural Bangladesh. We assessed the validity of a 42-item dish-based semi-quantitative food frequency questionnaire (FFQ using two 3-day food diaries (FDs. We selected a random subset of 47 families (190 participants from a longitudinal arsenic biomonitoring study in Bangladesh to administer the FFQ. Two 3-day FDs were completed by the female head of the households and we used an adult male equivalent method to estimate the FD for the other participants. Food and nutrient intakes measured by FFQ and FD were compared using Pearson’s and Spearman’s correlation, paired t-test, percent difference, cross-classification, weighted Kappa, and Bland–Altman analysis. Results showed good validity for total energy intake (paired t-test, p < 0.05; percent difference <10%, with no presence of proportional bias (Bland–Altman correlation, p > 0.05. After energy-adjustment and de-attenuation for within-person variation, macronutrient intakes had excellent correlations ranging from 0.55 to 0.70. Validity for micronutrients was mixed. High intraclass correlation coefficients (ICCs were found for most nutrients between the two seasons, except vitamin A. This dish-based FFQ provided adequate validity to assess and rank long-term dietary intake in rural Bangladesh for most food groups and nutrients, and should be useful for studying dietary-disease relationships.

  16. [Dysphagia caused by neurogenic deglutition disorders and diffuse idiopathic skeletal hyperostosis (DISH)].

    Science.gov (United States)

    Bremke, M; Wagner, H-J; Folz, B J

    2006-09-01

    Diffuse idiopathic skeletal hyperostosis (DISH) may lead to dysphagia caused by osteophytes of the cervical spine. Osteophytes can be resected transorally or transcervically, but operative ablation should not be indicated generously because of the threat of severe complications. A fifty-year-old man with dysphagia and loss of weight of 15 kg in the last three months is presented. He also suffered from a brain damage during infancy which caused grand-mal-seizures. One seizure lead to cardiac arrest which required cardio-pulmonary resuscitation and subsequent tracheostomy. A spheric tumor of the posterior pharyngeal wall could be seen endoscopically, it appeared radiologically as an osteophytic formation of the segments C (3) - C (5). Ossification of the anterior longitudinal ligament was also seen. Diagnosis of DISH was made on the basis of these results. Contrast imaging of the esophagus and videofluoroscopy showed aspiration in terms of neurogenic disorders. The patient received a percutaneous gastrostomy after his case was discussed with neurologic and orthopaedic colleagues, because a causal therapy of the combined disease seemed to be impossible. Dysphagia in the presented case was caused by a combination of neurogenic deglutition disorders and oropharyngeal obstruction through osteophytes. Surgical removal of the osteophytes was not indicated because it would have put the patient at a certain risk, but only a part of the underlying problem would have been removed. Symptomatic therapy with a gastrostomy secures normocaloric diet. The patient's weight remained stable and he can follow his habitual daily routine.

  17. Operational data and thermodynamic modeling of a Stirling-dish demonstration installation in desert conditions

    Science.gov (United States)

    Nilsson, Martin; Jamot, Jakob; Malm, Tommy

    2017-06-01

    To field test its Stirling-dish unit, Cleanergy AB of Sweden in Q1 2015 built a ten unit demo park in Dubai. The first STE (Solar Thermal Energy) generation of its Stirling genset, the C11S, had at its core an 11 kWel Stirling engine/generator combination. The genset was mated with a parabolic concentrator developed for the genset by a supplier. Local weather conditions in Dubai provide opportunities to test performance in an environment with high insolation and high ambient temperature. In addition, the conditions in Dubai are windy, salty, humid and dusty, historically challenging for solar technologies [1]. In Q1 2016 one of the C11S Stirling-dish units was replaced by the first prototype of Cleanergy's second generation Stirling genset, the Sunbox, and an in-house developed parabolic concentrator. Operational data from field testing during the spring of 2016 are presented and discussed and show the large performance improvement achieved with the Sunbox unit.

  18. Reflux heat-pipe solar receivers for dish-electric systems

    Science.gov (United States)

    Andraka, Charles E.; Diver, Richard B.

    1988-04-01

    The feasibility of competitive, modular bulk electric power from the sun may be greatly enhanced by the use of a reflux heat pipe receiver to combine a heat engine with a paraboloidal dish concentrator. This combination represents a potential improvement over previous successful demonstrations of dish-electric technology in terms of enhanced performance, lower cost, longer life, and greater flexibility in engine design. In the reflux (i.e., gravity assisted) heat pipe receiver, concentrated solar radiation causes liquid metal (sodium, potassium, or NaK) to evaporate. The vapor flows to the engine interface heat exchanger, where it condenses and releases the latent heat. The condensate is returned to the receiver absorber by gravity (refluxing), and distributed over the surface by gravity and/or capillary forces in a wick lining the receiver. It is essentially an adaptation of heat pipe technology to the peculiar requirements of concentrated solar flux, and provides many advantages over conventional heated tub receiver technology. This overview paper describes the current status and future plans for the U.S. Solar Thermal Program reflux receiver development program at Sandia National Laboratories. Current work includes conventional mesh wick receivers, sintered metal wicks, and pool boiler receivers. The relative design merits and concerns of the different approaches and technology development test plans are discussed.

  19. Embryo density may affect embryo quality during in vitro culture in a microwell group culture dish.

    Science.gov (United States)

    Lehner, Adam; Kaszas, Zita; Murber, Akos; Rigo, Janos; Urbancsek, Janos; Fancsovits, Peter

    2017-08-01

    Culturing embryos in groups is a common practice in mammalian embryology. Since the introduction of different microwell dishes, it is possible to identify oocytes or embryos individually. As embryo density (embryo-to-volume ratio) may affect the development and viability of the embryos, the purpose of this study was to assess the effect of different embryo densities on embryo quality. Data of 1337 embryos from 228 in vitro fertilization treatment cycles were retrospectively analyzed. Embryos were cultured in a 25 μl microdrop in a microwell group culture dish containing 9 microwells. Three density groups were defined: Group 1 with 2-4 (6.3-12.5 μl/embryo), Group 2 with 5-6 (4.2-5.0 μl/embryo), and Group 3 with 7-9 (2.8-3.6 μl/embryo) embryos. Proportion of good quality embryos was higher in Group 2 on both days (D2: 18.9 vs. 31.5 vs. 24.7%; p Culturing 5-6 embryos together in a culture volume of 25 μl may benefit embryo quality. As low egg number, position, and distance of the embryos may influence embryo quality, results should be interpreted with caution.

  20. Sensory attributes of dishes containing shrimp paste with different concentrations of glutamate and 5'-nucleotides.

    Science.gov (United States)

    Jinap, S; Ilya-Nur, A R; Tang, S C; Hajeb, P; Shahrim, K; Khairunnisak, M

    2010-10-01

    The shrimp paste called belacan is a traditional umami taste condiment extensively used in Malaysia that is rich in glutamate and 5'-nucleotides. The aim of this study was to determine the concentration of glutamate and 5'-nucleotides of various types of foods prepared with belacan and to measure their sensory attributes. The concentration of free glutamic acid found in different brands of belacan was 180-530mg/100g and in local dishes 601-4207mg/100g. The total amount of 5'-nucleotides in belacan samples ranged from 0.85 to 42.25μg/g. A Quantitative Descriptive Analysis (QDA) using a list of 17 sensory attributes showed a good correlation between belacan concentration in the final food and a range of positive sensory attributes, except for bitter, sweet, sour taste and astringency. Belacan also contains bitter, sweet and sour compounds that change the positive attributes of belacan at higher concentrations. The highest aroma attributes were linked to nasi goreng belacan (belacan fried rice) while the highest flavour attributes were found in sambal belacan. There was a 32 folds significant increase of umami attributes with the addition of belacan to final foods. The optimum amount of belacan was 0.45% for asam pedas (tamarind flavoured dish with belacan), 18% for sambal belacan (chilli belacan), 1.5-2.5% for kangkong goreng belacan (stir fried water convolous with belacan), and 2% for nasi goreng belacan.

  1. Analysis of solar water heater with parabolic dish concentrator and conical absorber

    Science.gov (United States)

    Rajamohan, G.; Kumar, P.; Anwar, M.; Mohanraj, T.

    2017-06-01

    This research focuses on developing novel technique for a solar water heating system. The novel solar system comprises a parabolic dish concentrator, conical absorber and water heater. In this system, the conical absorber tube directly absorbs solar radiation from the sun and the parabolic dish concentrator reflects the solar radiations towards the conical absorber tube from all directions, therefore both radiations would significantly improve the thermal collector efficiency. The working fluid water is stored at the bottom of the absorber tubes. The absorber tubes get heated and increases the temperature of the working fluid inside of the absorber tube and causes the working fluid to partially evaporate. The partially vaporized working fluid moves in the upward direction due to buoyancy effect and enters the heat exchanger. When fresh water passes through the heat exchanger, temperature of the vapour decreases through heat exchange. This leads to condensation of the vapour and forms liquid phase. The working fluid returns to the bottom of the collector absorber tube by gravity. Hence, this will continue as a cyclic process inside the system. The proposed investigation shows an improvement of collector efficiency, enhanced heat transfer and a quality water heating system.

  2. CPV semi-dense array design for dish and tower collectors

    Science.gov (United States)

    Hayden, Herb; Thomas, Paul; Fette, Nicholas; Farkas, Zoltan; Bading, Michael; Stone, Bradley; Miner, Mark; Stickroth, Oliver; Bagewadi, Nakul; Romero, Memo; Sonuparlak, Birol; Eichholz, Rainer; Ziegler, Michael; Pawlowski, Edgar

    2012-10-01

    SST is developing a new Dish CPV dense array system that overcomes the flux uniformity requirement of previous designs. The ability to operate without flux uniformity relaxes the precision requirements of primary collector optics and eliminates homogenizing optics previously required for dense array CPV. Array design can be configured for dish and tower/heliostat systems developed for thermal CSP applications. The design uses industry standard CPV cells and manufacturing materials and methods for minimum cost and high reliability. Nominal input flux to the array for full power is about 250 suns. Internal array optics increase flux to the cells to about 1200 suns. Linear optics provide additional concentration, permit novel use of commercial glass production methods and facilitate power collection design that is integrated with dynamic power conversion and maximum power point tracking (MPPT). Efficient power hybrid packaging methods are used along with advanced liquid cooling "cold-plate" thermal management. Byproduct "waste heat" can be provided for on-site CHP use. We report on the design approach and status of development with the beginning of on-sun alpha testing of the first of 50 kW of CPV modules being produced.

  3. Detailed Performance Analysis of the 10-Kw CNRS-Promes Dish/Stirling System

    Energy Technology Data Exchange (ETDEWEB)

    Reinalter, W.; Ulmer, S.; Heller, P.; Rauch, T.; Gineste, J. M.; Ferriere, A.; Nepveu, F.

    2006-07-01

    The CNRS-Promes dish/Stirling system was erected in June 2004 as the last of three country reference units built in the Envirodish project, partly financed by the German ministry of environment. It represents the latest development step of the EuroDish system with many improved components. With a measured peak of 11 kW electrical output power it is also the best performing system so far. The measurement campaign to determine the optical and thermodynamic efficiency of the system is presented. The optical quality of the concentrator and the energy input to the power conversion unit was measured with a classical flux-mapping system using a Lambertian target and a CCD camera system. For the thermodynamic analysis all the data necessary for a complete energy balance around the Stirling engine, i.e. efficiency of the Stirling motor, the cavity and the receiver as well as the parasitic losses were measured or approximated by calculations. Such a detailed performance analysis helps to quantify all significant losses of the system and to identify the most rewarding future improvements. (Author)

  4. Design, simulation and optimization of a solar dish collector with spiral-coil thermal absorber

    Directory of Open Access Journals (Sweden)

    Pavlović Saša R.

    2016-01-01

    Full Text Available The efficient conversion of solar radiation into heat at high temperature levels requires the use of concentrating solar collectors. The goal of this paper is to present the optical and the thermal analysis of a parabolic dish concentrator with a spiral coil receiver. The parabolic dish reflector consists of 11 curvilinear trapezoidal reflective petals constructed by PMMA with silvered mirror layer and has a diameter of 3.8 m, while its focal distance is 2.26m. This collector is designed with commercial software SolidWorks and simulated, optically and thermally in its Flow Simulation Studio. The optical analysis proved that the ideal position of the absorber is at 2.1m from the reflector in order to maximize the optical efficiency and to create a relative uniform heat flux over the absorber. In thermal part of the analysis, the energetic efficiency was calculated approximately 65%, while the exergetic efficiency is varied from 4% to 15% according to the water inlet temperature. Moreover, other important parameters as the heat flux and temperature distribution over the absorber are presented. The pressure drop of the absorber coil is calculated at 0.07bar, an acceptable value.

  5. Large Parabolic Dish collectors with small gas-turbine, Stirling engine or photovoltaic power conversion systems

    Energy Technology Data Exchange (ETDEWEB)

    Gehlisch, K.; Heikal, H.; Mobarak, A.; Simon, M.

    1982-08-01

    A comparison for different solar thermal power plants is presented and demonstrates that the large parabolic dish in association with a gas turbine or a Sterling engine could be a competitive system design in the net power range of 50-1000KW. The important advantages of the Large Parabolic Dish concept compared to the Farm and Tower concept are discussed: concentration ratios up to 5000 and uniform heat flux distribution throughout the day which allow very high receiver temperatures and therefor high receiver efficiency to operate effectively Stirling motors or small gas turbines in the mentioned power range with an overall efficiency of 20 to 30%. The high focal plane concentration leads to the efficient use of ceramic materials for receivers of the next generation, applicable in temperature ranges up to 1,300 /sup 0/C for energy converters. Besides the production of electricity, the system can supply process heat in the temperature range of 100 to 400 /sup 0/C as waste heat from the gas turbo converter and heat at temperature levels from 500 to 900 /sup 0/C (1300 /sup 0/C) directly out of the receiver.

  6. Performance tests and efficiency analysis of Solar Invictus 53S - A parabolic dish solar collector for direct steam generation

    Science.gov (United States)

    Jamil, Umer; Ali, Wajahat

    2016-05-01

    This paper presents the results of performance tests conducted on Solar Invictus 53S `system'; an economically effective solar steam generation solution designed and developed by ZED Solar Ltd. The system consists of a dual axis tracking parabolic solar dish and bespoke cavity type receiver, which works as a Once Through Solar Steam Generator `OTSSG' mounted at the focal point of the dish. The overall performance and efficiency of the system depends primarily on the optical efficiency of the solar dish and thermal efficiency of the OTSSG. Optical testing performed include `on sun' tests using CCD camera images and `burn plate' testing to evaluate the sunspot for size and quality. The intercept factor was calculated using a colour look-back method to determine the percentage of solar rays focused into the receiver. Solar dish tracking stability tests were carried out at different times of day to account for varying dish elevation angles and positions, movement of the sunspot centroid was recorded and logged using a CCD camera. Finally the overall performance and net solar to steam efficiency of the system was calculated by experimentally measuring the output steam parameters at varying Direct Normal Insolation (DNI) levels at ZED Solar's test facility in Lahore, Pakistan. Thermal losses from OTSSG were calculated using the known optical efficiency and measured changes in output steam enthalpy.

  7. Renewal of radiological equipment.

    Science.gov (United States)

    2014-10-01

    In this century, medical imaging is at the heart of medical practice. Besides providing fast and accurate diagnosis, advances in radiology equipment offer new and previously non-existing options for treatment guidance with quite low morbidity, resulting in the improvement of health outcomes and quality of life for the patients. Although rapid technological development created new medical imaging modalities and methods, the same progress speed resulted in accelerated technical and functional obsolescence of the same medical imaging equipment, consequently creating a need for renewal. Older equipment has a high risk of failures and breakdowns, which might cause delays in diagnosis and treatment of the patient, and safety problems both for the patient and the medical staff. The European Society of Radiology is promoting the use of up-to-date equipment, especially in the context of the EuroSafe Imaging Campaign, as the use of up-to-date equipment will improve quality and safety in medical imaging. Every healthcare institution or authority should have a plan for medical imaging equipment upgrade or renewal. This plan should look forward a minimum of 5 years, with annual updates. Teaching points • Radiological equipment has a definite life cycle span, resulting in unavoidable breakdown and decrease or loss of image quality which renders equipment useless after a certain time period.• Equipment older than 10 years is no longer state-of-the art equipment and replacement is essential. Operating costs of older equipment will be high when compared with new equipment, and sometimes maintenance will be impossible if no spare parts are available.• Older equipment has a high risk of failure and breakdown, causing delays in diagnosis and treatment of the patient and safety problems both for the patient and the medical staff.• Every healthcare institution or authority should have a plan for medical imaging equipment upgrade or replacement. This plan should look forward a

  8. [The consumption of dishes and/or fishy snacks by school youth from Miedzychodzko-Sierakowskie lakes].

    Science.gov (United States)

    Bortnowska, Grazyna; Grotowska, Longina; Goluch-Koniuszy, Zuzanna

    2011-01-01

    The school youth inhabiting Miedzychodzko-Sierakowskie lakes consumed dishes and/or fishy snacks on the similar low level as their peers in other regions of country, mainly breaded fried fishes and partly or highly manufactured products i.e., herrings in sour cream as well as pastes from smoked fishes and canned fishes. Relatively high ranks in rows of preference (liking) and frequency intake were found for carp, herring and cheap cultured panga from import. The presence of bones and specific odour were the factors that mostly affected low consumption of dishes and/or snacks from fishes. It seems that preparation of attractive tasty dishes and/or snacks from fresh fishes could help in youth teaching regarding correct nutritional habits as well as retain tradition of their consumption during adult life.

  9. Vegetable dishes, dairy products and fruits are key items mediating adequate dietary intake for Japanese adults with spinal cord injury.

    Science.gov (United States)

    Tsunoda, N; Inayama, T; Hata, K; Oka, J

    2015-11-01

    This is a cross-sectional study. The objective of this study was to ascertain the essential items mediating adequate dietary intake based on the Japanese Food Guide in common among the transtheoretical model (TTM), self-efficacy (SE) and outcome expectancy (OE). Members of the organization Spinal Injuries Japan. We posted a questionnaire survey to 2731 community-dwelling Japanese adults with spinal cord injury (SCI), and responses from 841 individuals were analyzed. Food intake was assessed as the frequency scores of 10 food items eaten in a daily diet in Japan. The correlations between the frequency scores of food intake and TTM, SE and OE were determined by binominal logistic regression analysis. The frequency scores of food intake were significantly associated with 'To eat vegetable dishes (dishes made mainly from vegetables or potatoes) not less than twice a day', 'To eat green/yellow vegetables not less than twice a day', 'To eat dairy products not less than once a day' and 'To eat fruits not less than once a day' in TTM. 'To eat vegetable dishes (dishes made mainly from vegetables or potatoes) not less than twice a day', 'To eat dairy products not less than once a day' and 'To eat fruits not less than once a day' were significantly associated with the frequency scores of food intake in SE. In OE, no differences were shown. This study finds that vegetable dishes, dairy products and fruits are the key items mediating adequate dietary intake. Dietary guidelines promoting the intake of these dishes for SCI individuals are needed.

  10. Solar-parabolic dish-Stirling-engine-system module. Task 1: Topical report, market assessment/conceptual design

    Energy Technology Data Exchange (ETDEWEB)

    1982-11-30

    The major activities reported are: a market study to identify an early market for a dish-Stirling module and assess its commercial potential; preparation of a conceptual system and subsystem design to address this market; and preparation of an early sales implementation plan. A study of the reliability of protection from the effects of walk-off, wherein the sun's image leaves the receiver if the dish is not tracking, is appended, along with an optical analysis and structural analysis. Also appended are the relationship between PURPA and solar thermal energy development and electric utility pricing rationale. (LEW)

  11. Solar-parabolic dish-Stirling-engine-system module. Task 1: Topical report, market assessment/conceptual design

    Energy Technology Data Exchange (ETDEWEB)

    1982-11-30

    The major activities reported are: a market study to identify an early market for a dish-Stirling module and assess its commercial potential; preparation of a conceptual system and subsystem design to address this market; and preparation of an early sales implementation plan. A study of the reliability of protection from the effects of walk-off, wherein the sun's image leaves the receiver if the dish is not tracking, is appended, along with an optical analysis and structural analysis. Also appended are the relationship between PURPA and solar thermal energy development and electric utility pricing rationale. (LEW)

  12. RETRIEVAL EQUIPMENT DESCRIPTIONS

    Energy Technology Data Exchange (ETDEWEB)

    J. Steinhoff

    1997-08-25

    The objective and the scope of this document are to list and briefly describe the major mobile equipment necessary for waste package (WP) retrieval from the proposed subsurface nuclear waste repository at Yucca Mountain. Primary performance characteristics and some specialized design features of the equipment are explained and summarized in the individual subsections of this document. There are no quality assurance requirements or QA controls in this document. Retrieval under normal conditions is accomplished with the same fleet of equipment as is used for emplacement. Descriptions of equipment used for retrieval under normal conditions is found in Emplacement Equipment Descriptions, DI: BCAF00000-01717-5705-00002 (a document in progress). Equipment used for retrieval under abnormal conditions is addressed in this document and consists of the following: (1) Inclined Plane Hauler; (2) Bottom Lift Transporter; (3) Load Haul Dump (LHD) Loader; (4) Heavy Duty Forklift for Emplacement Drifts; (5) Covered Shuttle Car; (6) Multipurpose Vehicle; and (7) Scaler.

  13. 2007 special equipment safety

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ The General Administration of Quality Supervision, Inspection and Quarantine of P.R.China (AQSIQ) issued a notice on May 28, 2007,requiring various locations to rectify their procedures for checking special equipment and hoisting machines for hidden problems. To further clarify and implement responsibility in the safety management of special equipment in enterprises, inspection responsibilities and test organizations related to technical assurance are to be established. Further, quality inspection departments will be supervised by law in order to improve special equipment safety.

  14. Medical equipment management

    CERN Document Server

    Willson, Keith; Tabakov, Slavik

    2013-01-01

    Know What to Expect When Managing Medical Equipment and Healthcare Technology in Your Organization As medical technology in clinical care becomes more complex, clinical professionals and support staff must know how to keep patients safe and equipment working in the clinical environment. Accessible to all healthcare professionals and managers, Medical Equipment Management presents an integrated approach to managing medical equipment in healthcare organizations. The book explains the underlying principles and requirements and raises awareness of what needs to be done and what questions to ask. I

  15. Modelització i control d'una màquina termosolar Dish-Stirling

    OpenAIRE

    Nieto Estévez, Albert

    2014-01-01

    En aquest projecte es realitza una modelització dinàmica d’un sistema d’energia termosolar concentrada Dish-Stirling i es dissenyen els convertidors estàtics back-to-back per optimitzar la potència extreta. Es presenta un model tèrmic per al sistema de concentració de radiació solar, un model termodinàmic del motor Stirling, el model elèctric d’un generador d’imants permanents i de convertidors de la màquina i de la xarxa. Els models s’implementen en MATLAB Simulink® i s’estudia el comp...

  16. Optical characterization of nonimaging dish concentrator for the application of dense-array concentrator photovoltaic system.

    Science.gov (United States)

    Tan, Ming-Hui; Chong, Kok-Keong; Wong, Chee-Woon

    2014-01-20

    Optimization of the design of a nonimaging dish concentrator (NIDC) for a dense-array concentrator photovoltaic system is presented. A new algorithm has been developed to determine configuration of facet mirrors in a NIDC. Analytical formulas were derived to analyze the optical performance of a NIDC and then compared with a simulated result obtained from a numerical method. Comprehensive analysis of optical performance via analytical method has been carried out based on facet dimension and focal distance of the concentrator with a total reflective area of 120 m2. The result shows that a facet dimension of 49.8 cm, focal distance of 8 m, and solar concentration ratio of 411.8 suns is the most optimized design for the lowest cost-per-output power, which is US$1.93 per watt.

  17. Cardiomyopathy in a dish: using human inducible pluripotent stem cells to model inherited cardiomyopathies.

    Science.gov (United States)

    Kamdar, Forum; Klaassen Kamdar, Andre; Koyano-Nakagawa, Naoko; Garry, Mary G; Garry, Daniel J

    2015-09-01

    Inherited cardiomyopathies, including hypertrophic cardiomyopathy, dilated cardiomyopathies, arrythmogenic right ventricular cardiomyopathy, and other inherited forms of heart failure, represent a unique set of genetically defined cardiovascular disease processes. Unraveling the molecular mechanisms of these deadly forms of human heart disease has been challenging, but recent groundbreaking scientific advances in stem cell technology have allowed for the generation of patient-specific human inducible stem cell (hiPSC)-derived cardiomyocytes (CMs). hiPSC-derived CMs retain the genetic blueprint of the patient, they can be maintained in culture, and they recapitulate the phenotypic characteristics of the disease in vitro, thus serving as a disease in a dish. This review provides an overview of in vitro modeling of inherited cardiomyopathies with the use of patient-specific hiPSC-derived CMs. Copyright © 2015. Published by Elsevier Inc.

  18. Optical Design of a Solar Dish Concentrator Based on Triangular Membrane Facets

    Directory of Open Access Journals (Sweden)

    Hongcai Ma

    2012-01-01

    Full Text Available The design of a solar dish concentrator is proposed based on triangular membrane facets for space power applications. The facet concentrator approximates a parabolic surface supported by a deployable perimeter truss structure, which originates from a large aperture space antenna. For optimizing the number of facets rows and focal-diameter ratio of the concentrator, Monte Carlo ray-tracing method is utilized to determine optical performance of the concentrator, and the system root-mean-square (RMS deviation is considered in this design procedure. A 600-facet concentrator with focal-diameter ratio of 1.1 will achieve 83.63% of radiative collection efficiency over a 15 cm radius disk located in the focal plane, with a mean solar concentration ratio exceeding 300. The study in this paper is helpful for the development of the membrane facet concentrator.

  19. Large-area, high-intensity PV arrays for systems using dish concentrating optics

    Energy Technology Data Exchange (ETDEWEB)

    Ward, J.S.; Duda, A.; Zweibel, K.; Coutts, T.J. [National Renewable Energy Lab., Golden, CO (United States)

    1998-09-01

    In this paper, the authors report on efforts to fabricate monolithic interconnected modules (MIMs) using III-V semiconductors with bandgaps appropriate for the terrestrial solar spectrum. The small size of the component cells comprising the MIM allows for operation at extremely high flux densities and relaxes the requirement for a small spot size to be generated by the optics. This makes possible a PV option for the large dish concentrator systems that have been developed by the solar thermal community for use with Stirling engines. Additionally, the highly effective back-surface reflector integrated into the MIM design is an effective tool for thermal management of the array. Development of this technology would radically alter the projections for PV manufacturing capacity because of the potential for extremely high power generation per unit area of semiconductor material.

  20. Thermal modeling of a pressurized air cavity receiver for solar dish Stirling system

    Science.gov (United States)

    Zou, Chongzhe; Zhang, Yanping; Falcoz, Quentin; Neveu, Pierre; Li, Jianlan; Zhang, Cheng

    2017-06-01

    A solar cavity receiver model for the dish collector system is designed in response to growing demand of renewable energy. In the present research field, no investigations into the geometric parameters of a cavity receiver have been performed. The cylindrical receiver in this study is composed of an enclosed bottom at the back, an aperture at the front, a helical pipe inside the cavity and an insulation layer on the external surface of the cavity. The influence of several critical receiver parameters on the thermal efficiency is analyzed in this paper: cavity inner diameter and cavity length. The thermal model in this paper is solved considering the cavity dimensions as variables. Implementing the model into EES, each parameter influence is separately investigated, and a preliminary optimization method is proposed.

  1. Automatic Evaluation of Colonies Growth rate of Yeasts incubated in Petri dishes using Mobile Platform

    Directory of Open Access Journals (Sweden)

    Alecsander Pereira Martins

    2015-10-01

    Full Text Available This paper proposes an automatic method based on computer vision implemented in mobile platform capable of monitoring the growth of microbial colonies incubated in Petri dishes. The developed optimized image processing algorithm performs this task without human intervention from images of colonies of the microorganism in different evolution phases. The contribution of this paper is the development of a fast and robust mobile tool to assist bioprocess experts in monitoring the growth of colonies without using the conventional error prone evaluation techniques. The obtained results successfully demonstrated dimensional alterations in colonies in a faster and more precise fashion when compared with the conventional method, with the additional advantage of versatility in producing reliable estimation of the growth rates with higher statistical significance.

  2. Modelling resource consumption for laundry and dish treatment in individual households for various consumer segments

    Energy Technology Data Exchange (ETDEWEB)

    Stamminger, R. [Institute for Agricultural Engineering, Household and Appliance Technology Section, University of Bonn, Nussallee 5, 53115 Bonn (Germany)

    2011-11-15

    Recent research allocates up to 80% of environmental impact in energy and CO2 terms to direct and indirect consumer activities. Various models discussed how this impact can be assigned to specific lifestyles, production and consumption systems, and psychological motives in order to be able to predict and influence these effects. In this work, another approach is followed by showing on the example of laundry and dish washing how well-known factors of the technical status, consumer practices and demographic data allow building up a model to predict the energy and water consumption for these processes. The results show a variation of a factor of 5 between a more sustainable and a more careless behaviour and allow thus to identify levers to influence it. As results can also be easily transformed into monetary values, this may allow influencing the consumer via this channel as he/she can easily understand what may need to be changed.

  3. Cost/performance of solar reflective surfaces for parabolic dish concentrators

    Science.gov (United States)

    Bouquet, F.

    1980-01-01

    Materials for highly reflective surfaces for use in parabolic dish solar concentrators are discussed. Some important factors concerning performance of the mirrors are summarized, and typical costs are treated briefly. Capital investment cost/performance ratios for various materials are computed specifically for the double curvature parabolic concentrators using a mathematical model. The results are given in terms of initial investment cost for reflective surfaces per thermal kilowatt delivered to the receiver cavity for various operating temperatures from 400 to 1400 C. Although second surface glass mirrors are emphasized, first surface, chemically brightened and anodized aluminum surfaces as well as second surface, metallized polymeric films are treated. Conventional glass mirrors have the lowest cost/performance ratios, followed closely by aluminum reflectors. Ranges in the data due to uncertainties in cost and mirror reflectance factors are given.

  4. Radio Astronomy Data Model for Single-Dish Multiple-Feed Telescopes, and Robledo Archive Architecture

    CERN Document Server

    Santander-Vela, J D; Gómez, J F; Verdes-Montenegro, L; Leon, S; Gutíerrez, R; Rodrigo, C; Morata, O; Solano, E; Suárez, O

    2008-01-01

    All the effort that the astrophysical community has put into the development of the Virtual Observatory (VO) has surpassed the non-return point: the VO is a reality today, and an initiative that will self-sustain, and to which all archival projects must adhere. We have started the design of the scientific archive for the DSS-63 70-m antenna at NASA's DSN station in Robledo de Chavela (Madrid). Here we show how we can use all VO proposed data models to build a VO-compliant single-dish, multiple-feed, radio astronomical archive data model (RADAMS) suitable for the archival needs of the antenna. We also propose an exhaustive list of Universal Content Descriptors (UCDs) and FITS keywords for all relevant metadata. We will further refine this data model with the experience that we will gain from that implementation.

  5. Spread spectrum mobile communication experiment using ETS-V satellite

    Science.gov (United States)

    Ikegami, Tetsushi; Suzuki, Ryutaro; Kadowaki, Naoto; Taira, Shinichi; Sato, Nobuyasu

    1990-01-01

    The spread spectrum technique is attractive for application to mobile satellite communications, because of its random access capability, immunity to inter-system interference, and robustness to overloading. A novel direct sequence spread spectrum communication equipment is developed for land mobile satellite applications. The equipment is developed based on a matched filter technique to improve the initial acquisition performance. The data rate is 2.4 kilobits per sec. and the PN clock rate is 2.4552 mega-Hz. This equipment also has a function of measuring the multipath delay profile of land mobile satellite channel, making use of a correlation property of a PN code. This paper gives an outline of the equipment and the field test results with ETS-V satellite.

  6. Satellite mobile data service for Canada

    Science.gov (United States)

    Egan, Glenn R.; Sward, David J.

    A commercial mobile satellite system which is to be constructed and operated in Canada is examined. This is done in two phases. First, mobile data services was introduced. Hub equipment and 3000 mobile data terminals were supplied. Over the satellite tests were performed. The mobile data service provides full two way digital messaging automatic vehicle location and fleet management services. The second phase is to construct, launch and make operational the MSAT satellite and associated network control facilities. The implementation is examined of the mobile data service in Canada, including the technical description. Marketing and applications are also examined.

  7. Technology Equipment Rooms.

    Science.gov (United States)

    Day, C. William

    2001-01-01

    Examines telecommunications equipment room design features that allow for growth and can accommodate numerous equipment replacements and upgrades with minimal service disruption and with minimal cost. Considerations involving the central hub, power and lighting needs, air conditioning, and fire protection are discussed. (GR)

  8. Workers intake too much salt from dishes of eating out and food service cafeterias; direct chemical analysis of sodium content.

    Science.gov (United States)

    Park, Hae-Ryun; Jeong, Gye-Ok; Lee, Seung-Lim; Kim, Jin-Young; Kang, Soon-Ah; Park, Kun-Young; Ryou, Hyun-Joo

    2009-01-01

    The average sodium intake of Koreans was reported to be 5,279.9 mg/day, which is one of the highest intake levels worldwide. The average Koreans intake 19.6% of sodium from kimchi, showing kimchi as the main contributor of sodium in this country (Ministry of Health and Welfare, 2005). The sodium content of dishes that are frequently chosen by workers, and which were served by foodservice cafeterias were chemically analyzed. The average sodium content of one meal provided by 10 foodservice cafeterias was 2,777.7 mg. Twenty-one, one-dish-meals, frequently chosen by workers for a lunch menu, were collected at 4 different restaurants for each menu by one male, aged in the twenties and analyzed chemically also. Workers who eat lunch at a workplace cafeteria everyday could intake about 8 g of salt at a one-time meal and those who eat out for a one-dish-meal would intake 3-8 g of salt without counting sodium content from the side dishes. From these study results, one could estimate that over 10 g of salt could be possible for a single meal for workers who eat out everyday. A nationwide nutrition campaign and education for low salt diets for restaurant owners and foodservice providers should be seriously considered.

  9. Effects of Modified Atmosphere Packaging, Food Life Extenders and Temperature on the Shelf Life of Ready-Made Dishes.

    Science.gov (United States)

    Sato, Jun; Maenishi, Takuya; Saito, Yuki; Masuda, Toshiro; Kadotani, Naoki; Kozakai, Hiroshi; Ito, Masanori

    2016-01-01

    The combined effect of several microbial control factors including gas barrier of containers, modified atmosphere packaging, food life extenders and storage temperature was discussed in order to determine the possibility for improving the shelf life for hamburger steak and deepfried chicken, representative ready-made dishes sold at convenience stores in Japan. Multiple measures including cold storage were effective in improving the shelf life of ready-made dishes. It was also suggested that storage tests for ready-made dishes should be conducted at 10℃, a practical temperature, to confirm the storable period, as well as at 15℃, an adequate abuse temperature, to confirm the effects of various microbial control factors. In the present study, the test group 4 (nitrogen + barrier containers + pH modifier) performed most favorably at both temperatures, indicating the efficacy of multiple means including "cold storage" in improving the shelf life (extending the consume-by date) of ready-made dishes. All strains isolated from the tested hamburger steak and deep-fried chicken were common food contaminant bacterial species.

  10. Food Safety: Recommendations for Determining Doneness in Consumer Egg Dish Recipes and Measurement of Endpoint Temperatures When Recipes Are Followed

    Directory of Open Access Journals (Sweden)

    Sandria Godwin

    2016-06-01

    Full Text Available Many consumers do not follow recommended food safety practices for cooking egg dishes, such as pies, quiches, and casseroles, potentially leading to foodborne illnesses such as Salmonellosis. The United States Department of Agriculture (USDA recommends cooking egg mixtures until the center reaches 71 °C (160 °F. The objectives of this study were to determine what endpoint temperature information consumers receive from egg dish recipes, and if recipes would lead to safe temperatures when followed. Egg dish recipes (n = 226 from 65 websites, 50 cookbooks, and nine magazine titles (multiple issues of each were analyzed. Time was the most frequently used indicator, given in 92% of the recipes, with 15% using only time. Other indicators included: set (89, browned (76, clean toothpick/knife (60, puffed (27, and jiggled (13. Only two recipes indicated final endpoint temperatures. Three recipes (a pie, a quiche, and an egg casserole were chosen and prepared in triplicate to see if they would reach recommended temperatures. The pie and quiche were still liquid at 71 °C, and were well over the recommended temperature when cooked according to instructions, but the egg casserole was not consistently above 71 °C, when the recipe instructions indicated it was done and the center was light brown and “jiggled” This research indicates that consumers are not receiving information on endpoint temperatures in egg recipes, but the likelihood of foodborne illness is low since most dishes probably be cooked past the recommended temperature before the consumer considers them done unless there are many inclusions that may absorb liquid and reduce the appearance of liquid in the dish.

  11. Observing the Sun with the Atacama Large Millimeter/submillimeter Array (ALMA): Fast-Scan Single-Dish Mapping

    Science.gov (United States)

    White, S. M.; Iwai, K.; Phillips, N. M.; Hills, R. E.; Hirota, A.; Yagoubov, P.; Siringo, G.; Shimojo, M.; Bastian, T. S.; Hales, A. S.; Sawada, T.; Asayama, S.; Sugimoto, M.; Marson, R. G.; Kawasaki, W.; Muller, E.; Nakazato, T.; Sugimoto, K.; Brajša, R.; Skokić, I.; Bárta, M.; Kim, S.; Remijan, A. J.; de Gregorio, I.; Corder, S. A.; Hudson, H. S.; Loukitcheva, M.; Chen, B.; De Pontieu, B.; Fleishmann, G. D.; Gary, D. E.; Kobelski, A.; Wedemeyer, S.; Yan, Y.

    2017-07-01

    The Atacama Large Millimeter/submillimeter Array (ALMA) radio telescope has commenced science observations of the Sun starting in late 2016. Since the Sun is much larger than the field of view of individual ALMA dishes, the ALMA interferometer is unable to measure the background level of solar emission when observing the solar disk. The absolute temperature scale is a critical measurement for much of ALMA solar science, including the understanding of energy transfer through the solar atmosphere, the properties of prominences, and the study of shock heating in the chromosphere. In order to provide an absolute temperature scale, ALMA solar observing will take advantage of the remarkable fast-scanning capabilities of the ALMA 12 m dishes to make single-dish maps of the full Sun. This article reports on the results of an extensive commissioning effort to optimize the mapping procedure, and it describes the nature of the resulting data. Amplitude calibration is discussed in detail: a path that uses the two loads in the ALMA calibration system as well as sky measurements is described and applied to commissioning data. Inspection of a large number of single-dish datasets shows significant variation in the resulting temperatures, and based on the temperature distributions, we derive quiet-Sun values at disk center of 7300 K at λ = 3 mm and 5900 K at λ = 1.3 mm. These values have statistical uncertainties of about 100 K, but systematic uncertainties in the temperature scale that may be significantly larger. Example images are presented from two periods with very different levels of solar activity. At a resolution of about 25'', the 1.3 mm wavelength images show temperatures on the disk that vary over about a 2000 K range. Active regions and plages are among the hotter features, while a large sunspot umbra shows up as a depression, and filament channels are relatively cool. Prominences above the solar limb are a common feature of the single-dish images.

  12. 日本海西南海域现场观测和卫星高度计获取的海面高度距平的比较研究%Comparison of sea surface height anomalies derived by pres-sure-sensor-equipped inverted echo sounders and satellite al-timetry in the Southwest Japan/East Sea

    Institute of Scientific and Technical Information of China (English)

    葛磊; 徐永生; 尹宝树

    2016-01-01

    Pressure-sensor-equipped inverted echo sounders (PIES) can be used to measure sea bottom pressure and the acoustic-wave propagation time from the seabed to the surface. Bottom pressure and the acoustic propagation time are used to estimate the contribution of the sea surface height anomaly (SLA) to water quality changes (positive pressure) and hema-tocrit changes (baroclinic), respectively. In this paper, we compare SLAs derived by PIES with SLAs derived from satellite altimetry data in the Southwest Japan/East Sea. Using correlation analysis, we compared the PIES SLAs with SLAs meas-ured by the along-track T/P satellite (TP SLA) and the ERS-2 satellite (ERS-2 SLA). We then compared the PIES SLA and AVISO gridded SLAs to estimate possible sources of error. We also analyzed the contributions of the PIES SLA positive pressure and baroclinic aspects of the SLA. The comparison results show that the correlation coefficient of the PIES SLA and Sat SLA is relatively high, and the root mean square error is relatively small. Further, we studied data from specific re-gions to identify possible causes of site-specific errors. Based on our results, we draw the following conclusions: (1) with respect to the Gulf Stream and the Kuroshio region, the contribution of positive sea surface height is relatively large; (2) if we consider the contribution of baroclinic changes in sea surface height, the PIES SLA and Sat SLA correlation coefficient will improve; (3) in the high-energy zone, the PIES SLA and Sat SLA correlation coefficient is relatively high and relatively better. Overall, in the Japan/East Sea, the PIES SLA and satellite altimeter SLA correlation coefficient is relatively high with a high level of consistency, providing a reliable way for checking the operation of Ocean II satellite (HY-2) altimeters. The research results have significance for the development and design of PIES, and for the selection of the placement of PIES.%压力传感逆式回声仪(pressure-sensor-equipped

  13. China Plans to Launch FY-3 Meteorological Satellite in 2006

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    China's new generation polar orbit weather satellite FY-3 will be launched by LM-4B launch vehicle in 2006. The FY-3 would be equipped with new global, all-weather, multi-spectral, threedimensional sensors. The new satellite, an improved version of the FY-1, has the resolution of 250m and

  14. Specification of the ASC to be used on the PRC satellite (HITSAT)

    DEFF Research Database (Denmark)

    Jørgensen, Finn E; Thuesen, Gøsta; Kilsgaard, Søren;

    1999-01-01

    The document describes the technical specifications of the ASC Star Tracker and the requirements for the equipment onboard the satellite HITSAT .......The document describes the technical specifications of the ASC Star Tracker and the requirements for the equipment onboard the satellite HITSAT ....

  15. Ozone dissolve dish treatment three times the waist dish outstanding disease dinical observation of the long-term outcome%臭氧三次溶盘治疗腰间盘突出症远期疗效的临床观察

    Institute of Scientific and Technical Information of China (English)

    彭万里; 郑磊峰; 李中堂

    2011-01-01

    目的:探讨臭氧三次溶盘治疗腰间盘突出症的远期疗效.方法:对600例臭氧三次溶盘治疗腰间盘突出症患者的远期疗效进行分析和随访.结果:臭氧三次溶盘治疗腰间盘突出症的远期疗效优于只进行一次臭氧溶盘的效果.优良率达89%.结论:臭氧三次溶盘治疗腰间盘突出症,远期疗效确切.%Objective: to study the treatment of ozone three soluble dish waist dish outstanding disorder long-term follow-up. Methods: three times to 600 cases of ozone waist dish outstanding dissolve dish therapy in patients with long-term outcome of analysis and follow-up. Results: ozone three dissolve dish waist dish outstanding disorder treatment of long-term outcome than just once the effect of ozone dissolve dish. Dykes of 89%. Conclusion: ozone three times the waist dish outstanding dissolve dish treatment), the long-term outcome exact.

  16. Electronic equipment packaging technology

    CERN Document Server

    Ginsberg, Gerald L

    1992-01-01

    The last twenty years have seen major advances in the electronics industry. Perhaps the most significant aspect of these advances has been the significant role that electronic equipment plays in almost all product markets. Even though electronic equipment is used in a broad base of applications, many future applications have yet to be conceived. This versatility of electron­ ics has been brought about primarily by the significant advances that have been made in integrated circuit technology. The electronic product user is rarely aware of the integrated circuits within the equipment. However, the user is often very aware of the size, weight, mod­ ularity, maintainability, aesthetics, and human interface features of the product. In fact, these are aspects of the products that often are instrumental in deter­ mining its success or failure in the marketplace. Optimizing these and other product features is the primary role of Electronic Equipment Packaging Technology. As the electronics industry continues to pr...

  17. Reliable Electronic Equipment

    Directory of Open Access Journals (Sweden)

    N. A. Nayak

    1960-05-01

    Full Text Available The reliability aspect of electronic equipment's is discussed. To obtain optimum results, close cooperation between the components engineer, the design engineer and the production engineer is suggested.

  18. Cooling of electronic equipment

    DEFF Research Database (Denmark)

    A. Kristensen, Anders Schmidt

    2003-01-01

    Cooling of electronic equipment is studied. The design size of electronic equipment decrease causing the thermal density to increase. This affect the cooling which can cause for example failures of critical components due to overheating or thermal induced stresses. Initially a pin fin heat sink...... is considered as extruded profiles are inadequate for compact designs. An optimal pin fin shape and configuration is sought also taking manufacturing costs into consideration. Standard methods for geometrical modeling and thermal analysis are applied....

  19. Quarry Equipment Yearbook 2003

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    This issue of the journal is devoted to an annual review of developments in the equipment used for minerals extraction and recycling. For each of 12 types of equipment, an editorial review is presented of developments and a tabular presentation of suppliers' ranges and contact information, including e-mail addresses and websites. The sections are: asphalt plants, conveyors, crushers and screens, drill rigs, dump trucks, excavators, hammers, pumps, tyres, weighbridges, wheel loaders and wheel washers.

  20. Association between Motives for Dish Choices during Home Meal Preparation and Weight Status in the NutriNet-Santé Study.

    Science.gov (United States)

    Ducrot, Pauline; Fassier, Philippine; Méjean, Caroline; Allès, Benjamin; Hercberg, Serge; Péneau, Sandrine

    2016-07-05

    Although home cooking has been associated with a lower body mass index in a few studies, no data exists on the motives behind food dish choices during home meal preparation and on their association with overweight. This study aimed to evaluate this association in 50,003 participants from the NutriNet-Santé cohort. Dimensions underlying the importance of 27 criteria possibly influencing dish choices were determined using an exploratory factor analysis. The association between dish choice motives and overweight (including obesity) was estimated using logistic regression models adjusted for sociodemographic and lifestyle characteristics. Five dimensions of dishes choice motives emerged: healthy diet (e.g., "nutritional balance of the dish"), constraints (e.g., "my cooking skills"), pleasure (e.g., "originality of the dish"), specific diets (e.g., "my health status"), and organization (e.g., "what I planned to eat"). A negative association was observed between the healthy diet factor and being overweight (OR = 0.65 (95% CI (confidence interval): 0.62-0.67)), whereas a positive association appeared for factors regarding pleasure (OR = 1.14 (95% CI: 1.10-1.19)) and specific diets (OR = 1.19 (95% CI: 1.17-1.22)). No significant associations were observed for constraints and organization. The significant associations between dish choice motives and overweight suggested the interest of focusing on these motives in order to promote healthier food choices during home cooking.

  1. Design and optimization of a single stage centrifugal compressor for a solar dish-Brayton system

    Science.gov (United States)

    Wang, Yongsheng; Wang, Kai; Tong, Zhiting; Lin, Feng; Nie, Chaoqun; Engeda, Abraham

    2013-10-01

    According to the requirements of a solar dish-Brayton system, a centrifugal compressor stage with a minimum total pressure ratio of 5, an adiabatic efficiency above 75% and a surge margin more than 12% needs to be designed. A single stage, which consists of impeller, radial vaned diffuser, 90° crossover and two rows of axial stators, was chosen to satisfy this system. To achieve the stage performance, an impeller with a 6:1 total pressure ratio and an adiabatic efficiency of 90% was designed and its preliminary geometry came from an in-house one-dimensional program. Radial vaned diffuser was applied downstream of the impeller. Two rows of axial stators after 90° crossover were added to guide the flow into axial direction. Since jet-wake flow, shockwave and boundary layer separation coexisted in the impeller-diffuser region, optimization on the radius ratio of radial diffuser vane inlet to impeller exit, diffuser vane inlet blade angle and number of diffuser vanes was carried out at design point. Finally, an optimized centrifugal compressor stage fulfilled the high expectations and presented proper performance. Numerical simulation showed that at design point the stage adiabatic efficiency was 79.93% and the total pressure ratio was 5.6. The surge margin was 15%. The performance map including 80%, 90% and 100% design speed was also presented.

  2. Comparison of advanced thermal and electrical storage for parabolic dish solar thermal power systems

    Science.gov (United States)

    Fujita, T.; Birur, G. C.; Schredder, J. M.; Bowyer, J. M.; Awaya, H. I.

    1982-01-01

    Parabolic dish solar concentrator cluster concepts are explored, with attention given to thermal storage systems coupled to Stirling and Brayton cycle power conversion devices. Sensible heat storage involving molten salt (NaOH), liquid sodium, and solid cordierite bricks are considered for 1500 F thermal storage systems. Latent heat storage with NaF-MgF2 phase change materials are explored in terms of passive, active, and direct contact designs. Comparisons are made of the effectiveness of thermal storage relative to redox, Na-S, Zn-Cl, and Zn-Br battery storage systems. Molten lead trickling down through a phase change eutectic, the NaF-MgF2, formed the direct contact system. Heat transport in all systems is effected through Inconel pipes. Using a cost goal of 120-150 mills/kWh as the controlling parameter, sensible heat systems with molten salts transport with either Stirling or Brayton engines, or latent heat systems with Stirling engines, and latent heat-Brayton engine with direct contact were favored in the analyses. Battery storage systems, however, offered the most flexibility of applications.

  3. Solar tests of aperture plate materials for solar thermal dish collectors

    Science.gov (United States)

    Jaffe, L. D.

    1984-11-01

    If a malfunction occurs in a solar thermal point-focus distributed receiver power plant while a concentrator is pointed at the sun, motion of the concentrator may stop. As the sun moves relative to the earth, the spot of concentrated sunlight then slowly walks off the receiver aperture, across the receiver face plate, and perhaps across adjacent portions of the concentrator. Intense local heating by the concentrated sunlight may damage or destroy these parts. The behavior of various materials under conditions simulating walk-off of a parabolic dish solar collector were evaluated. Each test consisted of exposure to concentrated sunlight at a peak flux density of about 7000 kW/square meter for 15 minutes. Types of materials tested included graphite, silicon carbide, silica, various silicates, alumina, zirconia, aluminum, copper, steel, and polytetrafluroethylene. The only material that neither cracked nor melted was grade G-90 graphite. Grade CS graphite, a lower cost commercial grade, cracked half-way across, but did not fail apart. Both of these grades are medium-grain extruded graphites. A graphite cloth (graphitized polyacrylonitrile) showed fair performance when tested as a single thin ply; it might be useful as a multi-ply assembly. High purity slipcast silica showed some promise also.

  4. Enhancing economic competiveness of dish Stirling technology through production volume and localization: Case study for Morocco

    Science.gov (United States)

    Larchet, Kevin; Guédez, Rafael; Topel, Monika; Gustavsson, Lars; Machirant, Andrew; Hedlund, Maria-Lina; Laumert, Björn

    2017-06-01

    The present study quantifies the reduction in the levelized cost of electricity (LCoE) and capital expenditure (CAPEX) of a dish Stirling power plant (DSPP) through an increase in localization and unit production volume. Furthermore, the localization value of the plant is examined to determine how much investment is brought into the local economy. Ouarzazate, Morocco, was chosen as the location of the study due to the country's favorable regulatory framework with regards to solar power technologies and its established industry in the concentrating solar power (CSP) field. A detailed techno-economic model of a DSPP was developed using KTH's in-house modelling tool DYESOPT, which allows power plant evaluation by means of technical and economic performance indicators. Results on the basis of LCoE and CAPEX were compared between two different cases of production volume, examining both a minimum and maximum level of localization. Thereafter, the DSPP LCoE and localization value were compared against competing solar technologies to evaluate its competitiveness. In addition, a sensitivity analysis was conducted around key design parameters. The study confirms that the LCoE of a DSPP can be reduced to values similar to solar photovoltaic (PV) and lower than other CSP technologies. Furthermore, the investment in the local economy is far greater when compared to PV and of the same magnitude to other CSP technologies. The competiveness of a DSPP has the potential to increase further when coupled with thermal energy storage (TES), which is currently under development.

  5. Solar reforming of methane in a direct absorption catalytic reactor on a parabolic dish

    Energy Technology Data Exchange (ETDEWEB)

    Muir, J.F.; Hogan, R.E. Jr.; Skocypec, R.D. (Sandia National Labs., Albuquerque, NM (USA)); Buck, R. (Deutsche Forschungsanstalt fuer Luft- und Raumfahrt e.V. (DLR), Stuttgart (Germany, F.R.). Inst. fuer Technische Thermodynamik)

    1990-01-01

    The concept of solar driven chemical reactions in a commercial-scale volumetric receiver/reactor on a parabolic concentrator was successfully demonstrated in the CAtalytically Enhanced Solar Absorption Receiver (CAESAR) test. Solar reforming of methane (CH{sub 4}) with carbon dioxide (CO{sub 2}) was achieved in a 64-cm diameter direct absorption reactor on a parabolic dish capable of 150 kW solar power. The reactor was a catalytic volumetric absorber consisting of a multi-layered, porous alumina foam disk coated with rhodium (Rh) catalyst. The system was operated during both steady-state and solar transient (cloud passage) conditions. The total solar power absorbed reached values up to 97 kW and the maximum methane conversion was 70%. Receiver thermal efficiencies ranged up to 85% and chemical efficiencies peaked at 54%. The absorber performed satisfactorily in promoting the reforming reaction during the tests without carbon formation. However, problems of cracking and degradation of the porous matrix, nonuniform dispersion of the Rh through the absorber, and catalyst deactivation due to sintering and possible encapsulation, must be resolved to achieve long-term operation and eventual commercialization. 17 refs., 11 figs., 1 tab.

  6. The small community solar thermal power experiment. Parabolic dish technology for industrial process heat application

    Science.gov (United States)

    Polzien, R. E.; Rodriguez, D.

    1981-01-01

    Aspects of incorporating a thermal energy transport system (ETS) into a field of parabolic dish collectors for industrial process heat (IPH) applications were investigated. Specific objectives are to: (1) verify the mathematical optimization of pipe diameters and insulation thicknesses calculated by a computer code; (2) verify the cost model for pipe network costs using conventional pipe network construction; (3) develop a design and the associated production costs for incorporating risers and downcomers on a low cost concentrator (LCC); (4) investigate the cost reduction of using unconventional pipe construction technology. The pipe network design and costs for a particular IPH application, specifically solar thermally enhanced oil recovery (STEOR) are analyzed. The application involves the hybrid operation of a solar powered steam generator in conjunction with a steam generator using fossil fuels to generate STEOR steam for wells. It is concluded that the STEOR application provides a baseline pipe network geometry used for optimization studies of pipe diameter and insulation thickness, and for development of comparative cost data, and operating parameters for the design of riser/downcomer modifications to the low cost concentrator.

  7. A two-stage approach to the treatment of hyperuricemia in gout: the "dirty dish" hypothesis.

    Science.gov (United States)

    Perez-Ruiz, Fernando; Herrero-Beites, Ana Maria; Carmona, Loreto

    2011-12-01

    It is commonly accepted that the target serum urate level in patients receiving urate-lowering therapy for dissolution of urate crystals in hyperuricemia of gout is gout should continue urate-lowering therapy for the rest of their lives. This study was undertaken to reevaluate whether this stringent therapeutic target to dissolve crystals must be maintained lifelong to prevent new crystal formation. In a prospective cohort of 211 patients with gout, urate-lowering therapy was withdrawn after 5 years if no tophus was present at baseline, or 5 years after resolution of the last tophus. Data on recurrence of gout and on serum urate levels and other potentially associated variables were analyzed. Multivariate regression analysis of time to crystal-proven recurrence of gout showed that serum urate levels during urate-lowering treatment and after its withdrawal were independently related to gout recurrence. None of the patients who had average serum urate levels of gout. Post hoc analysis showed that weight loss and use of drugs that lower serum urate, such as losartan or fenofibrate, were associated with serum urate levels of treatment of hyperuricemia in gout with urate crystal dissolution being the therapeutic target, lifelong treatment can be targeted to achieve serum urate levels just below the threshold for saturation to avoid new crystal formation, similar to cleaning a dirty dish: more is required to get it clean than to keep it clean. Copyright © 2011 by the American College of Rheumatology.

  8. Shallow releasing translation skills of dish name Of Chinese catering culture

    Institute of Scientific and Technical Information of China (English)

    罗青

    2012-01-01

    Human beings' catering culture penetrates every aspect of human beings, which includes catering culture, words of food, goods of food, and so on. As an old country having a five-thousandyear history, Chinese catering culture is also extensive and profound. As we all know, culture and food have go hand in glove, and Chinese dish name's translation also has unique Cultural connotations and features.%人类的饮食文化渗透于人类的方方面面,它包括饮食文化,饮食文字,饮食成品等。作为拥有五千年悠久历史的中华名族来说,饮食文化也同样博大精深。正如大家所知,文化和饮食是密不可分的,菜名的翻译在中国也有着独特的文化内涵与特色。

  9. Fabrication of Dish-Shaped Micro Parts by Laser Indirect Shocking Compound Process

    Directory of Open Access Journals (Sweden)

    Huixia Liu

    2016-06-01

    Full Text Available Compound process technology has been investigated for many years on a macro scale, but only a few studies can be found on a micro scale due to the difficulties in tool manufacturing, parts transporting and punch-die alignment. In this paper, a novel technology of combining the laser shock wave and soft punch was introduced to fabricate the dish-shaped micro-parts on copper to solve these difficulties. This compound process includes deep drawing, punching and blanking and these processes can be completed almost at the same time because the duration time of laser is quite short, so the precision of the micro-parts can be ensured. A reasonable laser energy of 1550 mJ made the morphology, depth of deformation, dimensional accuracy and surface roughness achieve their best results when the thickness of the soft punches was 200 μm. In addition, thicker soft punches may hinder the compound process due to the action of unloading waves based on the elastic wave theory. So, the greatest thickness of the soft punches was 200 μm.

  10. Charging studies of heat packs using parabolic dish solar energy concentrator for extreme conditions

    Science.gov (United States)

    Kumar, Rohitash; Vyas, Sumita; Kumar, Ravindra; Dixit, Ambesh

    2016-05-01

    Parabolic dish solar energy concentrator with aperture diameter 1.4 m and focal length 0.32 m is designed and fabricated to charge and store solar thermal energy in phase change material (PCM) based heat packs. Overall heat loss factor, heat duty, over all thermal efficiency, and optical efficiency factor are calculated using water sensible heating and cooling tests and values are 16.11 W m-2 K-1, 546.9 W, 49.2% and 0.62 respectively. The performance characteristic curve is generated using these parameters to understand its performance at different ambient temperatures and solar insolation. The fabricated concentrator has been used to charge 16 PCM heat packs with 150 g PCM in each heat pack, which took about 35 minutes for complete charging of PCM heat packs at average ambient temperature 39 °C and solar radiation flux density 715 W m-2 K-1. The charged heat packs are subjected to discharge studies at average ambient temperature about - 7 °C and observed heat release in the temperature range of 48 to 40 °C for 50 minutes, suggesting its applications for comfort and therapeutic applications in high altitude areas.

  11. Performance and cost of energy transport and storage systems for dish applications using reversible chemical reactions

    Science.gov (United States)

    Schredder, J. M.; Fujita, T.

    1984-01-01

    The use of reversible chemical reactions for energy transport and storage for parabolic dish networks is considered. Performance and cost characteristics are estimated for systems using three reactions (sulfur-trioxide decomposition, steam reforming of methane, and carbon-dioxide reforming of methane). Systems are considered with and without storage, and in several energy-delivery configurations that give different profiles of energy delivered versus temperature. Cost estimates are derived assuming the use of metal components and of advanced ceramics. (The latter reduces the costs by three- to five-fold). The process that led to the selection of the three reactions is described, and the effects of varying temperatures, pressures, and heat exchanger sizes are addressed. A state-of-the-art survey was performed as part of this study. As a result of this survey, it appears that formidable technical risks exist for any attempt to implement the systems analyzed in this study, especially in the area of reactor design and performance. The behavior of all components and complete systems under thermal energy transients is very poorly understood. This study indicates that thermochemical storage systems that store reactants as liquids have efficiencies below 60%, which is in agreement with the findings of earlier investigators.

  12. Comparison of advanced thermal and electrical storage for parabolic dish solar thermal power systems

    Science.gov (United States)

    Fujita, T.; Birur, G. C.; Schredder, J. M.; Bowyer, J. M.; Awaya, H. I.

    Parabolic dish solar concentrator cluster concepts are explored, with attention given to thermal storage systems coupled to Stirling and Brayton cycle power conversion devices. Sensible heat storage involving molten salt (NaOH), liquid sodium, and solid cordierite bricks are considered for 1500 F thermal storage systems. Latent heat storage with NaF-MgF2 phase change materials are explored in terms of passive, active, and direct contact designs. Comparisons are made of the effectiveness of thermal storage relative to redox, Na-S, Zn-Cl, and Zn-Br battery storage systems. Molten lead trickling down through a phase change eutectic, the NaF-MgF2, formed the direct contact system. Heat transport in all systems is effected through Inconel pipes. Using a cost goal of 120-150 mills/kWh as the controlling parameter, sensible heat systems with molten salts transport with either Stirling or Brayton engines, or latent heat systems with Stirling engines, and latent heat-Brayton engine with direct contact were favored in the analyses. Battery storage systems, however, offered the most flexibility of applications.

  13. Heat and electricity from the Sun using parabolic dish collector systems

    Science.gov (United States)

    Truscello, V. C.; Williams, A. N.

    1980-01-01

    Point focus distributed receiver solar thermal technology for the production of electric power and of industrial process heat is addressed. The thermal power systems project which emphasizes the development of cost effective systems which will accelerate the commercialization and industrialization of plants up to 10 MWe, using parabolic dish collectors is described. The projected size of the isolated load market in the 1990-2000 time period is 300 to 1000 MW/year. Although this market is small in comparison to the grid connected utility market, it is indicated that by assuming only a 20 percent market penetration, up to 10,000 power modules per year would be required to meet this need. At a production rate of 25,000 units/year and assuming no energy storage, levelized bus bar energy costs of 75 mills/kWeh are projected. These numbers are based on what is believed to be a conservative estimate regarding engine-generator conversion efficiency (40 percent) for the 1990 time period. With a more optimistic estimate of efficiency (i.e., 45 percent), the bus bar cost decreases to about 67 mills/kWeh. At very large production rates (400,000 modules/years), the costs decrease to 58 mills/kWeh. Finally, the present status of the technology development effort is discussed.

  14. Metabolic Profiling Directly from the Petri Dish Using Nanospray Desorption Electrospray Ionization Imaging Mass Spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Watrous, Jeramie D.; Roach, Patrick J.; Heath, Brandi S.; Alexandrov, Theodore; Laskin, Julia; Dorrestein, Pieter C.

    2013-11-05

    Understanding molecular interaction pathways in complex biological systems constitutes a treasure trove of knowledge that might facilitate the specific, chemical manipulation of the countless microbiological systems that occur throughout our world. However, there is a lack of methodologies that allow the direct investigation of chemical gradients and interactions in living biological systems, in real time. Here, we report the use of nanospray desorption electrospray ionization (nanoDESI) imaging mass spectrometry for in vivo metabolic profiling of living bacterial colonies directly from the Petri dish with absolutely no sample preparation needed. Using this technique, we investigated single colonies of Shewanella oneidensis MR-1, Bacillus subtilis 3610, and Streptomyces coelicolor A3(2) as well as a mixed biofilm of S. oneidensis MR-1 and B. subtilis 3610. Data from B. subtilis 3610 and S. coelicolor A3(2) provided a means of validation for the method while data from S. oneidensis MR-1 and the mixed biofilm showed a wide range of compounds that this bacterium uses for the dissimilatory reduction of extracellular metal oxides, including riboflavin, iron-bound heme and heme biosynthetic intermediates, and the siderophore putrebactin.

  15. Label-free interdigitated microelectrode based biosensors for bacterial biofilm growth monitoring using Petri dishes.

    Science.gov (United States)

    Paredes, Jacobo; Becerro, Sheila; Arana, Sergio

    2014-05-01

    Impedance microbiology (IM) is a known technique that has been applied during the last decades to detect the presence of microorganisms in real samples in different fields: food industry, healthcare, environment, etc. Bacterial biofilms however have not been so far studied despite the fact that they are the most common microbiological formation and that they present resistance to antimicrobial agents. In situ early detection of bacterial biofilm is still a challenge nowadays that causes huge impact in many different scenarios. The ability to detect biofilm generation early will allow better and more efficient treatments preventing high costs and important problems. In this work a new performance of this technique with interdigitated microelectrode sensors (IDE) is proposed. A specific culturing setup where the sensors have been integrated in Petri Dishes has been developed. From the results it can be highlighted that low frequencies are more sensitive for detection than higher ones. The results achieved record variations of approximately 40% in the equivalent serial resistance after 10h of culture. Electrical models have been successfully simulated to find the electrical behavior of the development of biofilms. Variations in both the capacitance and resistance were recorded during the growth of the microbes.

  16. Phenylketonuria: protein content and amino acids profile of dishes for phenylketonuric patients. The relevance of phenylalanine.

    Science.gov (United States)

    Pimentel, Filipa B; Alves, Rita C; Costa, Anabela S G; Torres, Duarte; Almeida, Manuela F; Oliveira, M Beatriz P P

    2014-04-15

    Phenylketonuria is an inborn error of metabolism, involving, in most cases, a deficient activity of phenylalanine hydroxylase. Neonatal diagnosis and a prompt special diet (low phenylalanine and natural-protein restricted diets) are essential to the treatment. The lack of data concerning phenylalanine contents of processed foodstuffs is an additional limitation for an already very restrictive diet. Our goals were to quantify protein (Kjeldahl method) and amino acid (18) content (HPLC/fluorescence) in 16 dishes specifically conceived for phenylketonuric patients, and compare the most relevant results with those of several international food composition databases. As might be expected, all the meals contained low protein levels (0.67-3.15 g/100 g) with the highest ones occurring in boiled rice and potatoes. These foods also contained the highest amounts of phenylalanine (158.51 and 62.65 mg/100 g, respectively). In contrast to the other amino acids, it was possible to predict phenylalanine content based on protein alone. Slight deviations were observed when comparing results with the different food composition databases.

  17. Solar tests of aperture plate materials for solar thermal dish collectors

    Science.gov (United States)

    Jaffe, L. D.

    1984-01-01

    If a malfunction occurs in a solar thermal point-focus distributed receiver power plant while a concentrator is pointed at the sun, motion of the concentrator may stop. As the sun moves relative to the earth, the spot of concentrated sunlight then slowly walks off the receiver aperture, across the receiver face plate, and perhaps across adjacent portions of the concentrator. Intense local heating by the concentrated sunlight may damage or destroy these parts. The behavior of various materials under conditions simulating walk-off of a parabolic dish solar collector were evaluated. Each test consisted of exposure to concentrated sunlight at a peak flux density of about 7000 kW/square meter for 15 minutes. Types of materials tested included graphite, silicon carbide, silica, various silicates, alumina, zirconia, aluminum, copper, steel, and polytetrafluroethylene. The only material that neither cracked nor melted was grade G-90 graphite. Grade CS graphite, a lower cost commercial grade, cracked half-way across, but did not fail apart. Both of these grades are medium-grain extruded graphites. A graphite cloth (graphitized polyacrylonitrile) showed fair performance when tested as a single thin ply; it might be useful as a multi-ply assembly. High purity slipcast silica showed some promise also.

  18. Geostationary Satellite (GOES) Images

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Visible and Infrared satellite imagery taken from radiometer instruments on SMS (ATS) and GOES satellites in geostationary orbit. These satellites produced...

  19. 47 CFR 80.905 - Vessel radio equipment.

    Science.gov (United States)

    2010-10-01

    ... the coverage of an INMARSAT maritime mobile geostationary satellite in which continuous alerting is... installed prior to February 12, 2004. (iv) Be equipped with a reserve power supply meeting the requirements... Relations, USCG Battery Park Building, Room 201, New York, NY 10004-1499. Phone 212-668-7764; Fax...

  20. Passivity Based Nonlinear Attitude Control of the Rømer Satellite

    DEFF Research Database (Denmark)

    Quottrup, Michael Melholt; Krogh-Sørensen, J.; Wisniewski, Rafal

    2001-01-01

    This paper suggests nonlinear attitude control of the Danish satellite Rømer. This satellite will be designed to fulfil two scientific objectives: The observation of stellar oscillations and the detection and localisation of gamma-ray bursts. The satellite will be equipped with a tetrahedron...

  1. Passivity based nonlinear attitude control of the Rømer satellite

    DEFF Research Database (Denmark)

    Quottrup, Michael Melholt; Krogh-Sørensen, J.; Wisniewski, Rafal

    This paper suggests nonlinear attitude control of the Danish satellite Rømer. This satellite will be designed to fulfil two scientific objectives: The observation of stellar oscillations and the detection and localisation of gamma-ray bursts. The satellite will be equipped with a tetrahedron...

  2. Neptune's small satellites

    Science.gov (United States)

    Thomas, P.

    1992-04-01

    The small satellites of Neptune and other planets discovered during the Voyager 2 mission are discussed in terms of their composition and relationship to the planetary systems. The satellite Proteus is described in terms of its orbit, five other satellites are described, and they are compared to ther small satellites and systems. Neptune's satellites are hypothesized to be related to the ring system, and the satellite Galatea is related to the confinement of the rings.

  3. Prediction and optimization of the performance of parabolic solar dish concentrator with sphere receiver using analytical function

    CERN Document Server

    Huang, Weidong; Hu, Peng; Chen, Zeshao

    2011-01-01

    Parabolic solar dish concentrator with sphere receiver is less studied. We present an analytic function to calculate the intercept factor of the system with real sun bright distribution and Gaussian distribution, the results indicate that the intercept factor is related to the rim angle of reflector and the ratio of open angle of receiver at the top of reflector to optical error when the optical error is larger than or equal to 5 mrad, but is related to the rim angle, open angle and optical error in less than 5 mrad optical error. Furthermore we propose a quick process to optimize the system to provide the maximum solar energy to net heat efficiency for different optical error under typical condition. The results indicate that the parabolic solar dish concentrator with sphere receiver has rather high solar energy to net heat efficiency which is 20% more than solar trough and tower system including higher cosine factor and lower heat loss of the receiver.

  4. Water Content in the SW USA Mantle Lithosphere: FTIR Analysis of Dish Hill and Kilbourne Hole Pyroxenites

    Science.gov (United States)

    Gibler, Robert; Peslier, Anne H.; Schaffer, Lillian Aurora; Brandon, Alan D.

    2014-01-01

    Kilbourne Hole (NM, USA) and Dish Hill (CA, USA) mantle xenoliths sample continental mantle in two different tectonic settings. Kilbourne Hole (KH) is located in the Rio Grande rift. Dish Hill (DH) is located in the southern Mojave province, an area potentially affected by subduction of the Farallon plate beneath North America. FTIR analyses were obtained on well characterized pyroxenite, dunite and wehrlite xenoliths, thought to represent crystallized melts at mantle depths. PUM normalized REE patterns of the KH bulk-rocks are slightly LREE enriched and consistent with those of liquids generated by 6% melting of a spinel peridotite source. Pyroxenite pyroxenes have no detectable water but one DH wehrlite, which bulk-rock is LREE enriched, has 4 ppm H2O in orthopyroxene and 2 Ga. The Farallon subduction appears to have enriched in water the southwestern United States lithospheric mantle further east than DH, beneath the Colorado plateau.

  5. 油缸用碟簧断裂分析%Fracture Analysis on 50 CrVA Steel Dished Spring

    Institute of Scientific and Technical Information of China (English)

    赵家利

    2014-01-01

    50CrVA钢制油缸用碟形弹簧在服役的早期发生断裂。采用直读光谱仪、洛氏硬度计、金相显微镜、扫描电镜等对该碟形弹簧的化学成分、硬度、非金属夹杂物、表面脱碳层、显微组织和断口形貌进行了分析。结果表明,50CrVA钢碟簧断裂是疲劳断裂,裂纹源由支撑面的加工硬化表层与次表层中的夹杂物共同作用所形成。提高碟簧使用寿命的措施是改善原材料的纯净度和提高表面加工质量。%Premature fracture of 50CrVA steel dished spring used in a oil vat occurred in service.The chemical composition,hardness,non-metallic inclusions,decarburized case,microstructure and fracture morphology of the dished spring were checked by direct-reading spectrometer,Rockwell hardness tester,OM and SEM.The results show that the rupture of the 50CrVA dished spring is a fatigue fracture,and the crack initiation arises from the action of work-hardened case of the support surface in combination with inclusions in the sublayer.Service life of the dished spring may be increased by an improvement on the raw material purity and increase in working quality of the surface.

  6. Experimental search for hidden photon CDM in the eV mass range with a dish antenna

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, J.; Horie, T. [Department of Physics, School of Science, The University of Tokyo,7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Inoue, Y. [International Center for Elementary Particle Physics, The University of Tokyo,7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Minowa, M. [Department of Physics, School of Science, The University of Tokyo,7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Research Center for the Early Universe (RESCEU), School of Science,The University of Tokyo,7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan)

    2015-09-15

    A search for hidden photon cold dark matter (HP CDM) using a new technique with a dish antenna is reported. From the result of the measurement, we found no evidence for the existence of HP CDM and set an upper limit on the photon-HP mixing parameter χ of ∼6×10{sup −12} for the hidden photon mass m{sub γ}=3.1±1.2 eV.

  7. Analytical methods to evaluate flux distributions from point-focus collectors for solar furnace and dish engine applications.

    Energy Technology Data Exchange (ETDEWEB)

    Khalsa, Siri Sahib; Siegel, Nathan Phillip; Ho, Clifford Kuofei

    2010-04-01

    This paper introduces a new analytical 'stretch' function that accurately predicts the flux distribution from on-axis point-focus collectors. Different dish sizes and slope errors can be assessed using this analytical function with a ratio of the focal length to collector diameter fixed at 0.6 to yield the maximum concentration ratio. Results are compared to data, and the stretch function is shown to provide more accurate flux distributions than other analytical methods employing cone optics.

  8. Experimental Search for Hidden Photon CDM in the eV mass range with a Dish Antenna

    OpenAIRE

    Suzuki, J; Horie, T.; Inoue, Y.; Minowa, M.

    2015-01-01

    A search for hidden photon cold dark matter (HP CDM) using a new technique with a dish antenna is reported. From the result of the measurement, we found no evidence for the existence of HP CDM and set an upper limit on the photon-HP mixing parameter $\\chi$ of $\\sim 6\\times 10^{-12}$ for the hidden photon mass $m_\\gamma = 3.1 \\pm 1.2$ eV.

  9. Experimental Search for Hidden Photon CDM in the eV mass range with a Dish Antenna

    CERN Document Server

    Suzuki, J; Inoue, Y; Minowa, M

    2015-01-01

    A search for hidden photon cold dark matter (HP CDM) using a new technique with a dish antenna is reported. From the result of the measurement, we found no evidence for the existence of HP CDM and set an upper limit on the photon-HP mixing parameter $\\chi$ of $\\sim 6\\times 10^{-12}$ for the hidden photon mass $m_\\gamma = 3.1 \\pm 1.2$ eV.

  10. Equipment Operational Requirements

    Energy Technology Data Exchange (ETDEWEB)

    Greenwalt, B; Henderer, B; Hibbard, W; Mercer, M

    2009-06-11

    The Iraq Department of Border Enforcement is rich in personnel, but poor in equipment. An effective border control system must include detection, discrimination, decision, tracking and interdiction, capture, identification, and disposition. An equipment solution that addresses only a part of this will not succeed, likewise equipment by itself is not the answer without considering the personnel and how they would employ the equipment. The solution should take advantage of the existing in-place system and address all of the critical functions. The solutions are envisioned as being implemented in a phased manner, where Solution 1 is followed by Solution 2 and eventually by Solution 3. This allows adequate time for training and gaining operational experience for successively more complex equipment. Detailed descriptions of the components follow the solution descriptions. Solution 1 - This solution is based on changes to CONOPs, and does not have a technology component. It consists of observers at the forts and annexes, forward patrols along the swamp edge, in depth patrols approximately 10 kilometers inland from the swamp, and checkpoints on major roads. Solution 2 - This solution adds a ground sensor array to the Solution 1 system. Solution 3 - This solution is based around installing a radar/video camera system on each fort. It employs the CONOPS from Solution 1, but uses minimal ground sensors deployed only in areas with poor radar/video camera coverage (such as canals and streams shielded by vegetation), or by roads covered by radar but outside the range of the radar associated cameras. This document provides broad operational requirements for major equipment components along with sufficient operational details to allow the technical community to identify potential hardware candidates. Continuing analysis will develop quantities required and more detailed tactics, techniques, and procedures.

  11. An objective method to measure cell survival by computer-assisted image processing of numeric images of Petri dishes

    Energy Technology Data Exchange (ETDEWEB)

    Biston, Marie-Claude [Equipe d' Accueil no 2941 ' Rayonnement Synchrotron et Recherche Medicale' , Unite IRM, CHU, BP 217, F-38043 Grenoble Cedex 09 (France); Corde, Stephanie [Equipe d' Accueil no 2941 ' Rayonnement Synchrotron et Recherche Medicale' , Unite IRM, CHU, BP 217, F-38043 Grenoble Cedex 09 (France); Camus, Emmanuel [Samba Technologies, ZIRST 53, chemin du Vieux Chene 38240 Meylan (France); Marti-Battle, Ramon [Samba Technologies, ZIRST 53, chemin du Vieux Chene 38240 Meylan (France); Esteve, Francois [Equipe d' Accueil no 2941 ' Rayonnement Synchrotron et Recherche Medicale' , Unite IRM, CHU, BP 217, F-38043 Grenoble Cedex 09 (France); Balosso, Jacques [Equipe d' Accueil no 2941 ' Rayonnement Synchrotron et Recherche Medicale' , Unite IRM, CHU, BP 217, F-38043 Grenoble Cedex 09 (France)

    2003-06-07

    This work establishes an objective method to measure cell clonogenic survival by computer-assisted image processing using images of cell cultures fixed and stained in Petri dishes. The procedure, developed by Samba Technologies, consists of acquiring Petri dish pictures with a desktop scanner and analysing them by computer, using algorithms based on the 'top hat' filter. The results from the automated count for the cell line SQ20B are compared with those found by two observers, before and after normalization of the counting. After normalization, the shape of the survival curves of the 'manual' counting of the Petri dishes shows a good correlation between both observers. The software enables the small visible differences in count between observers to be eliminated. The comparison between the absolute number of colonies shows an increased difference between the two manual scorings that can be as great as 67 colonies, whereas the difference between the two automated counts is never greater than 8 colonies. These results demonstrate that the 'manual' count is inter- and intra-observer variable, whereas the automatic count performs reproducible cell colony counts, thereby minimizing user-generated bias. The large amount of data produced also gives information about cell and colony characteristics. Thus, this computer-assisted method has considerably improved the reliability of our statistical results.

  12. Variations in Nutrients Composition of Most Commonly Consumed Cassava (Manihot esculenta Mixed Dishes in South-Eastern Nigeria

    Directory of Open Access Journals (Sweden)

    G. I. Davidson

    2017-01-01

    Full Text Available Variations in nutrient composition of most commonly consumed cassava (Manihot esculenta mixed dishes in South-eastern Nigeria were determined. Four communities were randomly selected from each of the five states in the South-east. Focus group discussions (FGD were conducted in each of the communities to determine commonly consumed foods and variations in recipes. 24-Hour dietary recall was conducted using 50 randomly selected households in those communities. Recipes collected during the FGD were standardized, prepared, and chemically analysed using standard methods. Data were analysed using descriptive statistics. Cassava-based dishes were the most commonly consumed in South-eastern Nigeria. Ninety-two percent of the study population ate cassava either in form of “fufu” (fermented cassava meal/garri (fermented and roasted cassava meal with soup or as “abacha” (tapioca salad. Commonly consumed soups were melon (Citrullus vulgaris seeds, “ora” (Pterocarpus soyauxii, and vegetable soups. Seven melon seed, six “ora,” and four vegetable soups and five “abacha” variations were identified. Except for vegetable soup, coefficient of variation for moisture was <10%, while large variations (19–71% were observed for energy and nutrients. These variations in cassava-based dishes need to be reflected in the country-specific food composition database to enable nutrient intake assessment or provision of dietary guidance using such food composition database as a reference material to be more effective.

  13. Molisan cuisine (names of dishes as an example of multiculturalism and multilingualism

    Directory of Open Access Journals (Sweden)

    Adrianna Słabińska

    2015-12-01

    Full Text Available Molisan cuisine (names of dishes as an example of multiculturalism and multilingualism Today Croats can be found living in many parts of the world. The process of Slavic migrations started in the 7th. Diasporas can be found in Austria, Slovakia, Romania, Czech Republic (Moravia and nowadays Prague, Serbia, Italy, even across the oceans in the USA, South America, RSA and Australia. The Croatian minority in Molise is the smallest Croatian minority in the world. Croatian is spoken there by about 2000 to 2400 people in three isolated mountain communities. They settled in villages, Kruč, Mundimitr and Filić possibly between the 14th and 15th century. Several Turkish invasions took place during this period, so Croats were forced to hide from the Sultan’s armies and they found refuge on the Apennine Peninsula. The country of Croatia, occupied with its battle against the infidels, has forgotten about its fellow countrymen, who had been living in the region of Molis, for a long time. In every day Croatian speech one can hear multiple loan-words. A particular problem can occur when writing some names of dishes which have been passed down but orally only. Molisan-Croatian cuisine and culinary names are part of Croatian cuisine that was created during the time of the Croatian Diaspora.   Kuchnia molizańska (nazwy potraw jako przykład wielokulturowości i wielojęzyczności Obecnie Chorwaci żyją na całym świecie. Proces migracji Słowian rozpoczął się już w VII wieku. Ich diaspory możemy odszukać w Austrii, Słowacji, Rumunii, Czechach (na Morawach i w obecnej Pradze i Serbii, Włoszech, a nawet za oceanem Atlantyckim w USA, południowej Ameryce, RPA i Australii. Najmniejszą chorwacką mniejszością narodową są Molizianie. Językiem chorwackim posługuje się od 2 do 2,4 tysięcy ludzi w trzech odizolowanych społecznościach. Początek osiedlenia się we wsiach: Kruču, Mundimitrze i Filiću określa się na XV–XVI wiek. Okres ten

  14. Dairy Equipment Lubrication

    Science.gov (United States)

    1978-01-01

    Lake To Lake Dairy Cooperative, Manitowoc, Wisconsin, operates four plants in Wisconsin for processing milk, butter and cheese products from its 1,300 member farms. The large co-op was able to realize substantial savings by using NASA information for improved efficiency in plant maintenance. Under contract to Marshall Space Flight Center, Midwest Research Institute compiled a handbook consolidating information about commercially available lubricants. The handbook details chemical and physical properties, applications, specifications, test procedures and test data for liquid and solid lubricants. Lake To Lake's plant engineer used the handbook to effect savings in maintenance labor and materials costs by reducing the number of lubricants used on certain equipment. Strict U.S. Department of Agriculture and Food and Drug Administration regulations preclude lubrication changes n production equipment, but the co-op's maintenance chief was able to eliminate seven types of lubricants for ancillary equipment, such as compressors and high pressure pumps. Handbook data enabled him to select comparable but les expensive lubricants in the materials consolidation process, and simplified lubrication schedules and procedures. The handbook is in continuing use as a reference source when a new item of equipment is purchased.

  15. Education Demonstration Equipment

    Science.gov (United States)

    Nagy, A.; Lee, R. L.

    2003-10-01

    The General Atomics fusion education program ``Scientist in the Classroom" (SIC) now in its sixth year, uses scientists and engineers to present plasma as a state of matter to students in the classroom. Using hands-on equipment, students see how magnets, gas pressure changes, and different gases are turned into plasmas. A piston, sealed volume, and vacuum chamber illuminate ideal gas laws. Liquid nitrogen is used to explore thermodynamic temperature effects and changes in states of matter. Light bulbs are excited with a Tesla coil to ionize gases, thus becoming an inexpensive plasma devices and a plasma tube shows magnetic interactions with plasma. The demonstration equipment used in this program is built with simple designs and common commercial equipment keeping in mind a teacher's tight budget. The SIC program ( ˜25 school presentations per year) has become very popular and has acquired an enthusiastic group of regular teacher clientele requesting repeat visits. In addition, three very popular and successful ``Build-It" days, sponsored by the General Atomics Fusion Education Outreach Program, enables teachers to build and keep in their classroom some of this equipment. The demonstration devices will be presented along with their ``build-it" details.

  16. Shipboard and laboratory equipment

    Digital Repository Service at National Institute of Oceanography (India)

    Shyamprasad, M.; Ramaswamy, V.

    bed, and a digital clock and a transponder helped to locate the camera. Equipment for the analysis of the nodules such as x-ray fluorescence and atomic absorption spectrophotometers were installed aboard MV Skandi Surveyor and MV Fernella and MV G A...

  17. Lifetime of Mechanical Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Leland, K.

    1999-07-01

    The gas plant at Kaarstoe was built as part of the Statpipe gas transport system and went on stream in 1985. In 1993 another line was routed from the Sleipner field to carry condensate, and the plant was extended accordingly. Today heavy additional supply- and export lines are under construction, and the plant is extended more than ever. The main role of the factory is to separate the raw gas into commercial products and to pump or ship it to the markets. The site covers a large number of well-known mechanical equipment. This presentation deals with piping, mechanical and structural disciplines. The lifetime of mechanical equipment is often difficult to predict as it depends on many factors, and the subject is complex. Mechanical equipment has been kept in-house, which provides detailed knowledge of the stages from a new to a 14 years old plant. The production regularity has always been very high, as required. The standard of the equipment is well kept, support systems are efficient, and human improvisation is extremely valuable.

  18. Satellite data compression

    CERN Document Server

    Huang, Bormin

    2011-01-01

    Satellite Data Compression covers recent progress in compression techniques for multispectral, hyperspectral and ultra spectral data. A survey of recent advances in the fields of satellite communications, remote sensing and geographical information systems is included. Satellite Data Compression, contributed by leaders in this field, is the first book available on satellite data compression. It covers onboard compression methodology and hardware developments in several space agencies. Case studies are presented on recent advances in satellite data compression techniques via various prediction-

  19. Trends in communications satellites

    CERN Document Server

    Curtin, Denis J

    1979-01-01

    Trends in Communications Satellites offers a comprehensive look at trends and advances in satellite communications, including experimental ones such as NASA satellites and those jointly developed by France and Germany. The economic aspects of communications satellites are also examined. This book consists of 16 chapters and begins with a discussion on the fundamentals of electrical communications and their application to space communications, including spacecraft, earth stations, and orbit and wavelength utilization. The next section demonstrates how successful commercial satellite communicati

  20. MODERNIZATION OF CUPOLA EQUIPMENT

    Directory of Open Access Journals (Sweden)

    S. L. Rovin

    2015-01-01

    Full Text Available This article presents an automated cupola complex, developed by scientific-production enterprise «Technolit» together with GSTU named after P. O. Sukhoi, launched in the spring of 2015 at the plant «Stroiex» in the city of Chelyabinsk (the Russian Federation. The old cupolas (open type have been replaced by the new cupolas of the closed type, equipped with automatic control and management system and multistage wet gas treatment system. Cupolas are equipped with systems of post-combustion gases and the batch charging, the separate systems of air blast, systems of sludge removal and recirculation of water, the slag granulation installations, mechanized cleaning of cupola furnace and automatic safety system. These activities allowed the company to increase production and improve the quality of cast iron, reduce the coke consumption by 20% and reducing emissions of pollutants into the atmosphere almost 30 times.

  1. Research on Satellite Fault Diagnosis and Prediction Using Multi-modal Reasoning

    Institute of Scientific and Technical Information of China (English)

    YangTianshe; SunYanhong; CaoYuping

    2004-01-01

    Diagnosis and prediction of satellite fault are more difficult than that of other equipment due to the complex structure of satellites and the presence of muhi-excite sources of satellite faults. Generally, one kind of reasoning model can only diagnose and predict one kind of satellite faults. In this paper the author introduces an application of a new method using multi-modal reasoning to diagnose and predict satellite faults. The method has been used in the development of knowledge-based satellite fault diagnosis and recovery system (KSFDRS) successfully. It is shown that the method is effective.

  2. Soviet equipment flies in

    CERN Multimedia

    CERN PhotoLab

    1978-01-01

    End of February 1977 a Soviet Ilyushin-76 heavy freight aircraft landed at Cointrin airport having on board fifty large wire proprtional chambers and associated apparatus, together weighing 10 tons, supplied by the Joint Institute for Nuclear Research, Dubna, USSR. The equipment was for the CERN- Dubna-Munich-Saclay experiment NA4 on deep inelastic muon scattering being set up in the North Area of SPS. See Weekly Bulletin 11/78.

  3. Equipment Obsolescence Management Program

    Energy Technology Data Exchange (ETDEWEB)

    Redmond, J.

    2014-07-01

    Nuclear Power Plant (NPP) Operators are challenged with securing reliable supply channels for safety related equipment due to equipment obsolescence. Many Original Equipment Manufacturers (OEMs) have terminated production of spare parts and product life-cycle support. The average component life cycles are much shorter than the NPP design life, which means that replacement components and parts for the original NPP systems are not available for the complete design life of the NPPs. The lack or scarcity of replacement parts adversely affects plant reliability and ultimately the profitability of the affected NPPs. This problem is further compounded when NPPs pursue license renewal and approval for plant-life extension. A reliable and predictable supply of replacement co components is necessary for NPPs to remain economically competitive and meet regulatory requirements and guidelines. Electrical and I and C components, in particular, have short product life cycles and obsolescence issues must be managed pro actively and not reactively in order to mitigate the risk to the NPP to ensure reliable and economic NPP operation. (Author)

  4. Equipment for gas conversion

    Energy Technology Data Exchange (ETDEWEB)

    Tabata, K.; Matsumoto, I.

    1983-01-28

    Equipment is proposed for vapor conversion of hydrocarbons (Uv), possibly in a mixture with air, in order to produce an inorganic gas, which chiefly consists of H2 and COx. It consists of a reaction pipe made of an inorganic refractory ceramic and equipped along the wall circumference with heaters. The reaction pipe is filled with a combined, multilayer catalyst (Kt) carrier, made of gamma-A1203 which in the transverse cross section has a multipore reticular or fibrous structure. Replacement of the traditional steel (St) materials for the walls of the reaction pipe with ceramic materials reduces the output of the hydrocarbon which contaminates the surface (Pv) of the catalyst; the use of a multilayer carrier for the catalyst made of gamma-A1203 with a porous reticular or fibrous structure reduces the pressure losses in the reactor and facilitates the replacement of the spent catalyst. The equipment is designed for vapor conversion of natural gas, C3H8, and vapors of kerosene, naphtha and so on.

  5. Economics of satellite communications systems

    Science.gov (United States)

    Pritchard, Wilbur L.

    This paper is partly a tutorial, telling systematically how one goes about calculating the total annual costs of a satellite communications system, and partly the expression of some original ideas on the choice of parameters so as to minimize these costs. The calculation of costs can be divided into two broad categories. The first is technical and is concerned with estimating what particular equipment will cost and what will be the annual expense to maintain and operate it. One starts in the estimation of any new system by listing the principal items of equipment, such as satellites, earth stations of various sizes and functions, telemetry and tracking equipment and terrestrial interfaces, and then estimating how much each item will cost. Methods are presented for generating such estimates, based on a knowledge of the gross parameters, such as antenna size, coverage area, transmitter power and information rate. These parameters determine the system performance and it is usually possible, knowing them, to estimate the costs of the equipment rather well. Some formulae based on regression analyses are presented. Methods are then given for estimating closely related expenses, such as maintenance and operation, and then an approximate method is developed for estimating terrestrial interconnection costs. It is pointed out that in specific cases when tariff and geographical information are available, it is usually better to work with specific data, but nonetheless it is often desirable, especially in global system estimating, to approximate these interconnect costs without recourse to individual tariffs. The procedure results in a set of costs for the purchase of equipment and its maintenance, and a schedule of payments. Some payments will be incurred during the manufacture of the satellite and before any systems operation, but many will not be incurred until the system is no longer in use, e.g. incentives. In any case, with the methods presented in the first section, one

  6. Configurable software for satellite graphics

    Energy Technology Data Exchange (ETDEWEB)

    Hartzman, P D

    1977-12-01

    An important goal in interactive computer graphics is to provide users with both quick system responses for basic graphics functions and enough computing power for complex calculations. One solution is to have a distributed graphics system in which a minicomputer and a powerful large computer share the work. The most versatile type of distributed system is an intelligent satellite system in which the minicomputer is programmable by the application user and can do most of the work while the large remote machine is used for difficult computations. At New York University, the hardware was configured from available equipment. The level of system intelligence resulted almost completely from software development. Unlike previous work with intelligent satellites, the resulting system had system control centered in the satellite. It also had the ability to reconfigure software during realtime operation. The design of the system was done at a very high level using set theoretic language. The specification clearly illustrated processor boundaries and interfaces. The high-level specification also produced a compact, machine-independent virtual graphics data structure for picture representation. The software was written in a systems implementation language; thus, only one set of programs was needed for both machines. A user can program both machines in a single language. Tests of the system with an application program indicate that is has very high potential. A major result of this work is the demonstration that a gigantic investment in new hardware is not necessary for computing facilities interested in graphics.

  7. Xichang Satellite Launch Center

    Institute of Scientific and Technical Information of China (English)

    LiuJie

    2004-01-01

    Xichang Satellite Launch Center(XSLC) is mainly for geosynchronous orbit launches. The main purpose of XSLC is to launch spacecraft, such as broadcasting,communications and meteorological satellites, into geo-stationary orbit.Most of the commercial satellite launches of Long March vehicles have been from Xichang Satellite Launch Center. With 20 years' development,XSLC can launch 5 kinds of launch vehicles and send satellites into geostationary orbit and polar orbit. In the future, moon exploration satellites will also be launched from XSLC.

  8. Handbook of satellite applications

    CERN Document Server

    Madry, Scott; Camacho-Lara, Sergio

    2017-01-01

    The first edition of this ground breaking reference work was the most comprehensive reference source available about the key aspects of the satellite applications field. This updated second edition covers the technology, the markets, applications and regulations related to satellite telecommunications, broadcasting and networking—including civilian and military systems; precise satellite navigation and timing networks (i.e. GPS and others); remote sensing and meteorological satellite systems. Created under the auspices of the International Space University based in France, this brand new edition is now expanded to cover new innovative small satellite constellations, new commercial launching systems, innovation in military application satellites and their acquisition, updated appendices, a useful glossary and more.

  9. Applications of two-way satellite time and frequency transfer in the BeiDou navigation satellite system

    Science.gov (United States)

    Zhou, ShanShi; Hu, XiaoGong; Liu, Li; Guo, Rui; Zhu, LingFeng; Chang, ZhiQiao; Tang, ChengPan; Gong, XiuQiang; Li, Ran; Yu, Yang

    2016-10-01

    A two-way satellite time and frequency transfer (TWSTFT) device equipped in the BeiDou navigation satellite system (BDS) can calculate clock error between satellite and ground master clock. TWSTFT is a real-time method with high accuracy because most system errors such as orbital error, station position error, and tropospheric and ionospheric delay error can be eliminated by calculating the two-way pseudorange difference. Another method, the multi-satellite precision orbit determination (MPOD) method, can be applied to estimate satellite clock errors. By comparison with MPOD clock estimations, this paper discusses the applications of the BDS TWSTFT clock observations in satellite clock measurement, satellite clock prediction, navigation system time monitor, and satellite clock performance assessment in orbit. The results show that with TWSTFT clock observations, the accuracy of satellite clock prediction is higher than MPOD. Five continuous weeks of comparisons with three international GNSS Service (IGS) analysis centers (ACs) show that the reference time difference between BeiDou time (BDT) and golbal positoning system (GPS) time (GPST) realized IGS ACs is in the tens of nanoseconds. Applying the TWSTFT clock error observations may obtain more accurate satellite clock performance evaluation in the 104 s interval because the accuracy of the MPOD clock estimation is not sufficiently high. By comparing the BDS and GPS satellite clock performance, we found that the BDS clock stability at the 103 s interval is approximately 10-12, which is similar to the GPS IIR.

  10. Differences in nutrient composition and choice of side dishes between red meat and fish dinners in Norwegian adults

    Directory of Open Access Journals (Sweden)

    Jannicke Borch Myhre

    2016-01-01

    Full Text Available Background: Food-based dietary guidelines often recommend increased consumption of fish and reduced intake of red and processed meat. However, little is known about how changing the main protein source from red meat to fish may influence the choice of side dishes. Objective: To investigate whether side dish choices differed between red meat and fish dinners. Moreover, to compare intakes of macronutrients and selected micronutrients in red meat and fish dinners and to see whether whole-day intakes of these nutrients differed between days with red meat dinners and days with fish dinners. Design: Data were collected in a cross-sectional nationwide Norwegian dietary survey using two non-consecutive telephone-administered 24-h recalls. The recalls were conducted approximately 4 weeks apart. In total, 2,277 dinners from 1,517 participants aged 18–70 were included in the analyses. Results: Fish dinners were more likely to include potatoes and carrots than red meat dinners, whereas red meat dinners more often contained bread, tomato sauce, and cheese. Red meat dinners contained more energy and iron; had higher percentages of energy (E% from fat, saturated fat, and monounsaturated fat; and a lower E% from protein and polyunsaturated fat than fish dinners. Fish dinners contained more vitamin D, β-carotene, and folate than red meat dinners. Similar differences were found when comparing whole-day intakes of the same nutrients on days with red meat versus fish dinners. Conclusion: Fish dinners were accompanied by different side dishes than red meat dinners. With regard to nutrient content, fish dinners generally had a healthier profile than red meat dinners. However, iron intake was higher for red meat dinners. Information about associated foods will be useful both for developing public health guidelines and when studying associations between dietary factors and health outcomes.

  11. Anàlisis d’un sistema d’energia renovable basat en un dish Stirling

    OpenAIRE

    Villà Sabé, Èric

    2016-01-01

    L’any 2015 li concedeixen a la Universitat Autònoma de Barcelona (UAB) un projecte europeu DIDSOLIT finançat per la UE, per avaluar el cost-benefici d’un sistema d’energia renovable. Davant d’aquest escenari, la UAB es va posa en contacte amb el centre CITCEA per dur a terme aquest projecte d’enginyeria. Posteriorment, es procedeix amb la compra d’un dish Stirling TRINUM a l’empresa INNOVA SOLAR, que és instal·lat a l’edifici del ETSEIB, UPC, Barcelona. Davant d’aquesta oportunitat, es pro...

  12. Pros and Cons of Using Arrays of Small Antennas Versus Large Single Dish Antennas for the Deep Space Network

    Science.gov (United States)

    Bagri, Durgadas S.

    2009-01-01

    This paper briefly describes pros and cons of using arrays of small antennas instead of large single dish antennas for spacecraft telemetry, command, and tracking (TT and C) - communications and navigation (C and N) - and science support that the Deep Space Network (DSN) normally provides. It considers functionality and performance aspects, mainly for TT and C, though it also considers science. It only briefly comments on the cost aspects that seem to favor arrays of small antennas over large single antennas, at least for receiving (downlinks).

  13. Materials compatibility in Dish-Stirling solar generators using Cu-Si-Mg eutectic for latent heat storage

    Science.gov (United States)

    Kruizenga, A. M.; Withey, E. A.; Andraka, C. E.; Gibbs, P. J.

    2016-05-01

    Dish-Stirling systems are a strong candidate to meet cost production goals for solar thermal power production. Thermal energy storage improves the capacity factor of thermal power systems; copper-silicon-magnesium eutectic alloys have been investigated as potential latent heat storage materials. This work examines the ability of commercially available plasma spray coatings to serve as protective barriers with these alloys, while highlighting mechanistic insights into materials for latent heat storage systems. Computed tomography was leveraged as a rapid screening tool to assess the presence of localized attack in tested coatings.

  14. Designing the next phase domestic satellites - A step to communication satellites as intelligent network nodes

    Science.gov (United States)

    Majus, J.

    1982-09-01

    Applications of satellite systems for telecommunication networks are discussed in terms of harmonizing the satellite capabilities with ground-based equipment, and design for the satellites are discussed. Modern network services are becoming increasingly digitized and use optic fiber switching and information transfer. Spaceborne nodes can be used for telephony, television, packet switching, leased lines, and teletex, with reserved sectors for point-to-point communications. Space systems are capable of 100% coverage, while terrestrial systems frequently have utilization rates near 5%, implying that demand-oriented satellite expansion of local systems is the suitable methodology. Technological requirements are explored, including exclusive use of digital processing, flexible flow rates, signal transmission times, and short time availability.

  15. How to Use Equipment Therapeutically.

    Science.gov (United States)

    Bowne, Douglas

    1986-01-01

    Shares therapeutic and economic practices surrounding equipment used in New York's Higher Horizons adventure program of therapy for troubled youth. Encourages educators, therapists, and administrators to explore relationship between equipment selection, program goals, and clients. (NEC)

  16. Satellite-Delivered Learning.

    Science.gov (United States)

    Arnall, Gail C.

    1987-01-01

    Discusses the application of satellite information delivery to training. Describes a new trend, horizontal programming. Also discusses vertical programming and in-house production of training materials. Lists vendors of satellite-based training. (CH)

  17. GPS Satellite Simulation Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The GPS satellite simulation facility consists of a GPS satellite simulator controlled by either a Silicon Graphics Origin 2000 or PC depending upon unit under test...

  18. China's Recoverable Satellites

    Institute of Scientific and Technical Information of China (English)

    Tang Boehang

    2008-01-01

    @@ By the end of 2006, China had launched 24 recoverable satellites (FSW) in total. Among them, 23 were launched successfully, of which all but one were successfully recovered. Recoverable satellites launched by China are listed in Table 1.

  19. Satellite Tags- Hawaii EEZ

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Satellite tagging was implemented in 2013. Satellite tagging is conducted using a Dan Inject air rifle and deployment arrows designed by Wildlife Computers. Two...

  20. NIH Standard. Animal Care Equipment.

    Science.gov (United States)

    National Institutes of Health (DHEW), Bethesda, MD. Office of Administrative Management.

    The National Institutes of Health standardized animal care equipment is presented in this catalog. Each piece of equipment is illustrated and described in terms of overall dimensions, construction, and general usage. A price list is included to estimate costs in budgeting, planning, and requisitioning animal care equipment. The standards and…

  1. Satellite communication engineering

    CERN Document Server

    Kolawole, Michael Olorunfunmi

    2013-01-01

    An undeniably rich and thorough guide to satellite communication engineering, Satellite Communication Engineering, Second Edition presents the fundamentals of information communications systems in a simple and succinct way. This book considers both the engineering aspects of satellite systems as well as the practical issues in the broad field of information transmission. Implementing concepts developed on an intuitive, physical basis and utilizing a combination of applications and performance curves, this book starts off with a progressive foundation in satellite technology, and then moves on

  2. Abyssal soil investigation equipment

    Energy Technology Data Exchange (ETDEWEB)

    Smits, F.P.; Maggioni, W.; Mainardi, U. [ISMES, Bergamo (Italy)

    1994-12-31

    The present paper deals with the development of a testing device for quick offshore geotechnical investigations. The equipment, at present, consists of a penetrometer, mounted on a sea bed platform, a handling frame and a control cabin; a further development includes a drill rig and a geotechnical laboratory. All this is designed so as to be an autonomous unit that can be handled by various types of non-specialized ships which have the necessary deck space. The sea bed platform can operate in 2,000 m of waterdepth and is provided with a hydraulic penetrometer, with a thrust capacity of 400 kN, able to carry out cone penetration type testing until a depth of more than 100 m, as well as shallow depth continuous sampling. The penetrometer can be equipped with a series of probes (piezocone, pressiocone, total radial pressure transducer, seismic cone) allowing the execution of the wide range of direct geotechnical measurements normally performed during on-land penetration tests.

  3. Progress in satellite quantum key distribution

    Science.gov (United States)

    Bedington, Robert; Arrazola, Juan Miguel; Ling, Alexander

    2017-08-01

    Quantum key distribution (QKD) is a family of protocols for growing a private encryption key between two parties. Despite much progress, all ground-based QKD approaches have a distance limit due to atmospheric losses or in-fibre attenuation. These limitations make purely ground-based systems impractical for a global distribution network. However, the range of communication may be extended by employing satellites equipped with high-quality optical links. This manuscript summarizes research and development which is beginning to enable QKD with satellites. It includes a discussion of protocols, infrastructure, and the technical challenges involved with implementing such systems, as well as a top level summary of on-going satellite QKD initiatives around the world.

  4. Taiyuan Satellite Launch Center

    Institute of Scientific and Technical Information of China (English)

    LiuJie

    2004-01-01

    There are three major space launch bases in China, the Jiuquan Satellite Launch Center,the Taiyuan Satellite Launch Center and the Xichang Satellite Launch Center. All the three launch centers are located in sparsely populated areas where the terrain is even and the field of vision is broad. Security, transport conditions and the influence of the axial rotation

  5. Geodetic Secor Satellite

    Science.gov (United States)

    1974-06-01

    simple, and had low-power lem. 17 14. Satellite Orientation . The satellite was designed to maintain a constant relationship between the antenna...the same satellite orientation . Further considerations were Th oscillations, however, when higher orbital ranges (500-2500 nautical miles) -, 3 a

  6. TC-2 Satellite Delivered

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    On April 18, 2005, TC-2, the second satellite of Double Star Program (DSP), which was jointly developed by CNSA and ESA, was approved to be delivered to the user after the on-board test and trial operation. The satellite is working well and the performance can meet the user's need. The satellite has collected large amount of valuable scientific data

  7. Technical comparison of several global mobile satellite communications systems

    Science.gov (United States)

    Comparetto, Gary M.

    The era of satellite-based mobile satellite communications (MSC) systems started with the first MARISAT satellite which was launched into a geostationary orbit over the Pacific Ocean in 1976 to provide communications between ships and shore stations. The combination of high cost and unacceptably large equipment has kept the space-based MSC systems from appealing to the wider market of personal mobile communications. The progress made over the last ten years, however, in digital voice processing, satellite technology, and component miniaturization has resulted in the viability of satellite-based mobile satellite communications systems to meet the growing market in personal mobile communications using handsets similar to those currently in use with land-based cellular systems. Three of the more mature LEO/MEO satellite systems are addressed in this paper including GLOBALSTAR, Iridium, and Odyssey. The system architectures of each system are presented along with a description of the satellite and user handset designs and the multiaccess techniques employed. It will be shown that, although a number of similarities exist among the system addressed, each system is unique in a variety of significant design areas. It is concluded that the technical feasibility of satellite-based mobile satellite communications systems seems to be secure. It will be challenging, however, for the vendors to actually develop and deploy these systems in a cost effective, timely, and reliable way that meets a continually evolving set of requirements based upon a rapidly changing technology base.

  8. Field measurements of dry deposition to spruce foliage and petri dishes in the black forest, F.R.G.

    Science.gov (United States)

    Shanley, James B.

    Dry deposition fluxes of Ca 2+, Mg 2+ , K +, Mn 2+, Pb 2+ and SO 2-4 to spruce foliage and petri dishes were measured in two high-elevation sites ( > 900 m) in the southern Black Forest, F.R.G., during 12 periods (2-7 days, each) from mid-September to mid-November, 1983, In situ extraction of deposited material from small spruce branches allowed repeated use of the same foliar collecting surfaces for a direct comparison of deposition between periods. Fluxes were corrected for leaching of internally cycled constituents using factors determined from serial extraction experiments. The ratio of flux to petri dishes vs foliage ( P/F) was > 1.0 for Ca 2+, Pb 2+ and SO 2-4, and somewhat < 1.0 but more constant for Mg 2+ . Temporal variations in dry deposition fluxes at an exposed site near the industrialized Rhine Valley correlated with variations in total air particulate concentrations at a nearby air quality station. Deposition rates were comparable in magnitude but different in temporal pattern at a remote site in the Black Forest interior. Fluxes at each site reached a minimum during the period of 4-9 November when a regional air inversion confined pollutants to the Rhine Valley below the study sites. High fluxes accompanied the inversion break-up.

  9. Validity and reliability of a dish-based, semi-quantitative food frequency questionnaire for Korean diet and cancer research.

    Science.gov (United States)

    Park, Min Kyung; Noh, Hwa Young; Song, Na Yeun; Paik, Hee Young; Park, Sohee; Joung, Hyojee; Song, Won O; Kim, Jeongseon

    2012-01-01

    This study evaluated the validity and reliability of applying a newly developed dish-based, semi-quantitative food frequency questionnaire (FFQ) for Korean diet and cancer research. The subjects in the present study were 288 Korean adults over 30 years of age who had completed two FFQs and four 3-day diet records (DRs) from May 2008 to February 2009. Student's t-tests, Chi-square tests, and Spearman's rank correlation coefficients were used to estimate and compare intakes from different dietary assessment tools. Agreement in quintiles was calculated to validate agreement between the results of the second FFQ (FFQ-2) conducted in February 2009 and the DRs. Median Spearman's correlation coefficients between the intake of nutrients and foods assessed by the FFQ-1 and FFQ-2 were 0.59 and 0.57, respectively, and the coefficients between the intake of nutrients and foods assessed by the FFQ-2 and the DRs were 0.31 and 0.29, respectively. The quintile classifications of same or adjacent quintile for intake of nutrients and foods were 64% and 65%, respectively. Misclassification into opposite quintiles occurred in less than 5% for all dietary factors. Thus this newly-developed, Korean dish-based FFQ demonstrated moderate correspondence with the four 3-day DRs. Its reliability and validity are comparable to those reported in other studies.

  10. Analysis of ewe’s milk by FT Near Infrared spectroscopy: measurement of samples on Petri dishes in reflectance mode

    Directory of Open Access Journals (Sweden)

    Květoslava Šustová

    2006-01-01

    Full Text Available Our work deals with a possibility of determination of basic composition (dry matter, fat, protein, casein, lactose and urea nitrogen of ewe’s milk and colostrum by FT NIR spectroscopy. Samples of milk were warmed to 40 °C, agitated, cooled to 20 °C, transferred into Petri dishes and analysed by reference methods and by FT NIR in reflectance mode. The measured area was spaced by a metallic mirror. Statistically significant differences between the reference values and the calculated values of NIR were not found (p=0.05. Results of calibration for ewe’s milk determined the highest correlation coefficients: dry matter 0.983, fat 0.989, true protein 0.997, casein 0.977, lactose 0.980 and urea nitrogen 0.973. The study showed that NIRS method, when samples of milk are measured on Petri dishes, is a useful technique for the prediction of dry matter, fat, protein and casein in ewe’s milk.

  11. A Food Photograph Series for Identifying Portion Sizes of Culturally Specific Dishes in Rural Areas with High Incidence of Oesophageal Cancer

    Directory of Open Access Journals (Sweden)

    Marjanne Senekal

    2013-08-01

    Full Text Available Rural areas of the Eastern Cape (EC Province, South Africa have a high incidence of squamous cell oesophageal cancer (OC and exposure to mycotoxin fumonisin has been associated with increased OC risk. However, to assess exposure to fumonisin in Xhosas—having maize as a staple food—it is necessary to determine the amount of maize consumed per day. A maize-specific food frequency questionnaire (M-FFQ has recently been developed. This study developed a food photograph (FP series to improve portion size estimation of maize dishes. Two sets of photographs were developed to be used alongside the validated M-FFQ. The photographs were designed to assist quantification of intakes (portion size photographs and to facilitate estimation of maize amounts in various combined dishes (ratio photographs using data from 24 h recalls (n = 159, dishing-up sessions (n = 35, focus group discussions (FGD (n = 56 and published literature. Five villages in two rural isiXhosa-speaking areas of the EC Province, known to have a high incidence of OC, were randomly selected. Women between the ages of 18–55 years were recruited by snowball sampling and invited to participate. The FP series comprised three portion size photographs (S, M, L of 21 maize dishes and three ratio photographs of nine combined maize-based dishes. A culturally specific FP series was designed to improve portion size estimation when reporting dietary intake using a newly developed M-FFQ.

  12. Remanufacturing strategy for chemical equipment

    Institute of Scientific and Technical Information of China (English)

    ZHANG Xian-cheng; XU Bin-shi; WANG Hai-dou; JIANG Yi; WU Yi-xiong; GONG Jian-ming; TU Shan-dong

    2005-01-01

    Failure, especially induced by cracks, usually occurred in the service process of chemical equipment, which could cause the medium leakage, fire hazard and explosion and induced the personnel casualty and economic losses. To assure the long-term and safety service, it is necessary to apply the remanufacturing technology on the chemical equipment containing cracks. The recent research advances on the remanufacturing, the failure modes and the life extension technology for chemical equipment were reviewed. The engineering strategy of the remanufacturing for the chemical equipment was proposed, which could provide a reasonable and reliable technical route for the remanufacturing operation of chemical equipment. In the strategy, the redesign was also been considered.

  13. Weather satellite picture receiving stations, APT digital scan converter

    Science.gov (United States)

    Vermillion, C. H.; Kamowski, J. C.

    1975-01-01

    The automatic picture transmission digital scan converter is used at ground stations to convert signals received from scanning radiometers to data compatible with ground equipment designed to receive signals from vidicons aboard operational meteorological satellites. Information necessary to understand the circuit theory, functional operation, general construction and calibration of the converter is provided. Brief and detailed descriptions of each of the individual circuits are included, accompanied by a schematic diagram contained at the end of each circuit description. Listings of integral parts and testing equipment required as well as an overall wiring diagram are included. This unit will enable the user to readily accept and process weather photographs from the operational meteorological satellites.

  14. Satellite medical centers project

    Science.gov (United States)

    Aggarwal, Arvind

    2002-08-01

    World class health care for common man at low affordable cost: anywhere, anytime The project envisages to set up a national network of satellite Medical centers. Each SMC would be manned by doctors, nurses and technicians, six doctors, six nurses, six technicians would be required to provide 24 hour cover, each SMC would operate 24 hours x 7 days. It would be equipped with the Digital telemedicine devices for capturing clinical patient information and investigations in the form of voice, images and data and create an audiovisual text file - a virtual Digital patient. Through the broad band connectivity the virtual patient can be sent to the central hub, manned by specialists, specialists from several specialists sitting together can view the virtual patient and provide a specialized opinion, they can see the virtual patient, see the examination on line through video conference or even PCs, talk to the patient and the doctor at the SMC and controlle capturing of information during examination and investigations of the patient at the SMC - thus creating a virtual Digital consultant at the SMC. Central hub shall be connected to the doctors and consultants in remote locations or tertiary care hospitals any where in the world, thus creating a virtual hub the hierarchical system shall provide upgradation of knowledge to thedoctors in central hub and smc and thus continued medical education and benefit the patient thru the world class treatment in the smc located at his door step. SMC shall be set up by franchisee who shall get safe business opportunity with high returns, patients shall get Low cost user friendly worldclass health care anywhere anytime, Doctors can get better meaningful selfemplyment with better earnings, flexibility of working time and place. SMC shall provide a wide variety of services from primary care to world class Global consultation for difficult patients.

  15. Phased Array Transmit Antenna for a Satellite

    Science.gov (United States)

    Huggins, R. W.; Heisen, P. T.; Miller, G. E.; McMeen, D. J.; Perko, K. L.

    1999-01-01

    Active phased array antennas with electronically scanned beams offer advantages over high gain parabolic dish antennas currently used on spacecraft. Benefits include the elimination of deployable structures, no moving parts, and no torque disturbances that moving antennas impart to the spacecraft. The latter results in the conservation of spacecraft power, and the ability to take precision optical data while transmitting data. Such an antenna has been built under a contract from NASA Goddard Space Flight Center for the New Millennium Program EO- 1 satellite where it will act as the primary highspeed scientific data communication link. The antenna operates at X-band, has an integral controller and power conditioner, communicates with the spacecraft over a 1773 optical data bus, and is space qualified for low earth orbit (705 Km altitude). The nominal mission length is one year, and the operational requirement is for one 10 minute transmission a day over Spitsbergen, Norway. Details of the antenna and its performance will be described in the following paper.

  16. Meteorological satellite systems

    CERN Document Server

    Tan, Su-Yin

    2014-01-01

    “Meteorological Satellite Systems” is a primer on weather satellites and their Earth applications. This book reviews historic developments and recent technological advancements in GEO and polar orbiting meteorological satellites. It explores the evolution of these remote sensing technologies and their capabilities to monitor short- and long-term changes in weather patterns in response to climate change. Satellites developed by various countries, such as U.S. meteorological satellites, EUMETSAT, and Russian, Chinese, Japanese and Indian satellite platforms are reviewed. This book also discusses international efforts to coordinate meteorological remote sensing data collection and sharing. This title provides a ready and quick reference for information about meteorological satellites. It serves as a useful tool for a broad audience that includes students, academics, private consultants, engineers, scientists, and teachers.

  17. Theory of geostationary satellites

    CERN Document Server

    Zee, Chong-Hung

    1989-01-01

    Geostationary or equatorial synchronous satellites are a daily reminder of our space efforts during the past two decades. The nightly television satellite weather picture, the intercontinental telecommunications of television transmissions and telephone conversations, and the establishrnent of educational programs in remote regions on Earth are constant reminders of the presence of these satellites. As used here, the term 'geo­ stationary' must be taken loosely because, in the long run, the satellites will not remain 'stationary' with respect to an Earth-fixed reference frame. This results from the fact that these satellites, as is true for all satellites, are incessantly subject to perturbations other than the central-body attraction of the Earth. Among the more predominant pertur­ bations are: the ellipticity of the Earth's equator, the Sun and Moon, and solar radiation pressure. Higher harmonics of the Earth's potential and tidal effects also influence satellite motion, but they are of second­ order whe...

  18. Chang'e-1 Satellite Completed Its Preset Objectives

    Institute of Scientific and Technical Information of China (English)

    He Ying

    2008-01-01

    @@ By October 23, Chang'e-1 satellite with a one-year design lifetime has been operating in lunar orbit for one year, completed more than 4000 orbits, covering the entire moon 12 times. The satellite's platform works normally at present and all systems and equipment onboard work in their main mode. The satellite has obtained a large quantity of scientific data and achieved the preset objectives of precise orbit maneuver, successful moon orbiting, effective exploration and oneyear lifetime. The Chang'e-1 mission is a complete success.

  19. Uses of communication satellites in water utility operations

    Science.gov (United States)

    Tighe, W. S.

    This paper proposes a system to serve the communications needs of the operating side of a water utility and estimates the requirements and capabilities of the equipment needed. The system requires the shared use of a satellite transponder with 100% backup. Messages consist of data packets containing data and control information, plus voice transmission. Satellite communication may have a price advantage in some instances over wire line or VHF radio and have greater survivability in case of a natural disaster. Water and other utilities represent a significant market for low cost mass produced satellite earth terminals.

  20. Child and parent perspectives on healthier side dishes and beverages in restaurant kids' meals: results from a national survey in the United States.

    Science.gov (United States)

    Shonkoff, Eleanor T; Anzman-Frasca, Stephanie; Lynskey, Vanessa M; Chan, Grace; Glenn, Meaghan E; Economos, Christina D

    2017-07-25

    Children frequently consume foods from restaurants; considering the quick-service sector alone, 1/3 of children eat food from these restaurants on a given day, and among these consumers, 1/3 of their daily calories come from fast food. Restaurant foods and beverages are second only to grocery store foods and beverages in their contribution to total energy intake of U.S. 4- to 11-year-olds. Shifting their restaurant consumption in healthier directions could have a positive impact on child health. In 2014 this study examined self-reported child receptivity and parent awareness of child receptivity to ordering a fruit or vegetable side dish instead of French fries; and milk, water, or flavored water instead of soda/pop with a kids' meal when eating out. Child receptivity to side dishes was compared between 2010 and 2014. An online survey was administered by Nielsen via their Harris Poll Online to a national panel of 711 parents and their 8- to 12-year-old child, as part of a larger study. Frequencies, logistic regressions, t-tests, chi-square tests, and percent agreement were used to evaluate child likelihood of ordering certain side dishes; receptivity to healthier side dish and beverage alternatives; changes in receptivity to healthier sides across years; and parent awareness. A majority of children said they were likely to order a meal with a vegetable (60%), fruit (78%), or French fry (93%) side dish. They were receptive to receiving a fruit or vegetable (FV) side dish instead of French fries (68%); or milk, water, or flavored water instead of soda (81%) with their restaurant kids' meal. Liking/taste was the most common reason for children's feelings. Child receptivity to a FV side dish instead of French fries was high in both years and significantly higher in 2014 (t = -2.12, p = 0.034). The majority of parent and child reports of child receptivity were concordant (85%). These national survey results indicate that children are receptive to FV side dishes and

  1. Communication satellites to enter a new age of flexibility

    Science.gov (United States)

    Balty, Cédric; Gayrard, Jean-Didier; Agnieray, Patrick

    2009-07-01

    To cope with the economical and technical evolutions of the communication market and to better compete with or complement terrestrial networks, satellite operators are requiring more flexible satellites. It allows a better fleet planning potential and back-up policy, a more standardized and efficient procurement process, mission adaptation to market evolution and the possibility of early entry in new markets. New technologies that are developed either for terrestrial networks or for space defense applications would become soon available to satellite and equipment manufacturers. A skilful mix of these new technologies with the older and more mature ones should boost satellite performances and bring flexibility to the new generation of communication satellites. This paper reviews the economical and technical environment of the space communication business for the next decade. It identifies the needs and levels of flexibility that are required by the market but also allowed by technologies, in both a top-down and bottom-up approach.

  2. Vibration and acoustic testing of TOPEX/Poseidon satellite

    Science.gov (United States)

    Boatman, Dave; Scharton, Terry; Hershfeld, Donald; Larkin, Paul

    1992-01-01

    The satellite was subjected to a 1.5G swept sine vibration test and a 146 dB overall level acoustic test, in accordance with Ariane launch vehicle requirements, at the NASA Goddard Space Flight Center. Extensive pretest analysis of the sine test was conducted to plan the input notching and to justify vibration testing the satellite only in the longitudinal axis. A unique measurement system was utilized to determine the six components of interface force between the shaker and the satellite in the sine vibration test. The satellite was heavily instrumented in both the sine vibration and acoustic test in order to insure that the launch loads were enveloped with appropriate margin and that satellite responses did not exceed the compatibilities of the structure and equipment. The test specification, objectives, instrumentation, and test results are described herein.

  3. Association between the frequency of meals combining "Shushoku, Shusai, and Hukusai" (Staple food, main dish, and side dish) and intake of nutrients and food groups among Japanese young adults aged 18-24 years: a cross-sectional study.

    Science.gov (United States)

    Kakutani, Yuya; Kamiya, Saori; Omi, Naomi

    2015-01-01

    "Shushoku," "Shusai," and "Hukusai" are staple food, main dish, and side dish, respectively. The recommended meal in Japan is a combination of "Shushoku," "Shusai," and "Hukusai"; however, it remains unclear whether there is an association between the frequency of these meals and intake of nutrients and food groups. This cross-sectional study examined the association between the frequency of meals combining "Shushoku, Shusai, and Hukusai" and intake of nutrients and food groups among 664 Japanese young adults aged 18-24 y. The dietary habits of the subjects during the preceding month were assessed using a validated brief-type self-administered diet history questionnaire. The frequency of meals combining "Shushoku, Shusai, and Hukusai" was self-reported according to four categories: "less than 1 d or 1 d/wk," "2 or 3 d/wk," "4 or 5 d/wk," and "every day." In both women and men, there was an association between the higher frequency of these meals and higher intake of the following food groups: pulses, green and yellow vegetables, other vegetables, mushrooms, seaweeds, fish and shellfish, and eggs. Moreover, there was an association with higher intake of protein, polyunsaturated fat, n-6 and n-3 polyunsaturated fat, total dietary fiber, soluble and insoluble dietary fiber, β-carotene, α-tocopherol, vitamin K, thiamin, riboflavin, folate, pantothenic acid, vitamin C, potassium, calcium, magnesium, iron, and copper, and lower intake of carbohydrate in both women and men. Our findings support the hypothesis that the meals combining "Shushoku, Shusai, and Hukusai" may be associated with intake of many food groups and nutrients among Japanese young adults.

  4. Advantages of Hybrid Global Navigation Satellite Systems

    Directory of Open Access Journals (Sweden)

    Asim Bilajbegović

    2007-05-01

    Full Text Available In a decision-making situation, what kind of GPS equipment to purchase, one always has a dilemma, tobuy hybrid (GPS+GLONASS or only GPS receivers? In the case of completeness of the GLONASS satellite system, this dilemma probably would not have existed. The answer to this dilemma is given in the present paper, but for the constellation of the GLONASS satellites in summer 2006 (14 satellites operational. Due to the short operational period of these satellites (for example GLONASS-M, 5 years, and not launching new ones, at this moment (February 25, 2007, only 10 satellites are operational. For the sake of research and giving answers to these questions, about 252 RTK measurements have been done using (GPS and GNSS receivers, on points with different obstructions of horizon. Besides that, initialisation time has been investigated for both systems from about 480 measurements, using rover's antenna with metal cover, during a time interval of 0.5, 2 and 5 seconds. Moreover, accuracy, firmware declared accuracy and redundancy of GPS and GNSS RTK measurements have been investigating.  

  5. Difficult airway equipment: a survey of standards across metropolitan Perth.

    Science.gov (United States)

    Alakeson, N; Flett, T; Hunt, V; Ramgolam, A; Reynolds, W; Hartley, K; Hegarty, M; von Ungern-Sternberg, B S

    2014-09-01

    The importance of appropriate equipment to manage the difficult airway has been highlighted by the publication of the Australian and New Zealand College of Anaesthetists (ANZCA) guidelines in 2012. We set out to audit compliance with these guidelines in all public and private sites providing general anaesthesia in metropolitan Perth. Public and private health care websites identified 39 sites of which 37 were studied. Institutional and ethics approval was obtained. A tick-box design audit tool, based on the ANZCA guidelines, was used to collect information regarding the dedicated difficult airway container (DDAC) at each site. As recommended in the guidelines, only equipment within the DDAC was considered. Further data about each site, including the number of theatre suites, satellite anaesthetic areas, use of capnography and categories of patients treated (adult, obstetric and paediatric) were collected. An adult DDAC was found at 92% of all sites, but none of the sites had all the essential equipment listed in the ANZCA guidelines. There was limited provision of adult difficult airway equipment within private sites compared to public, and less provision of paediatric difficult airway equipment across all sites treating paediatric patients in metropolitan Perth. Capnography was available in 76% of post anaesthesia care units and used regularly in 27%. Adherence to the ANZCA guidelines regarding the DDAC could be improved. Standardised equipment across a metropolitan region would be of value in the management of the difficult airway.

  6. Information technology equipment cooling system

    Science.gov (United States)

    Schultz, Mark D.

    2014-06-10

    According to one embodiment, a system for removing heat from a rack of information technology equipment may include a sidecar indoor air to liquid heat exchanger that cools warm air generated by the rack of information technology equipment. The system may also include a liquid to liquid heat exchanger and an outdoor heat exchanger. The system may further include configurable pathways to connect and control fluid flow through the sidecar heat exchanger, the liquid to liquid heat exchanger, the rack of information technology equipment, and the outdoor heat exchanger based upon ambient temperature and/or ambient humidity to remove heat from the rack of information technology equipment.

  7. Tax Adjusted for Imported Equipment

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    @@ Ministry of Finance, Central Administration of Customs, and State Administration of Taxation of P.R. of China jointly issued a "Notice on the Lists Related to the Interim Provisions on the Adjustment of Import Tax Policy on Major Technical Equipment" (the Notice) on April 13rd to adjust the list of equipment catalog and merchandise attached to the "Interim Provisions on the Import Tax Policy on Major Technical Equipment", as well as the preferential scope and extent of the import tax on a number of major technical equipment.

  8. Power Product Equipment Technician: Equipment Systems. Teacher Edition. Student Edition.

    Science.gov (United States)

    Hilley, Robert

    This packet contains teacher and student editions on the topic of equipment systems, intended for the preparation of power product equipment technicians. This publication contains seven units: (1) principles of power transmission; (2) mechanical drive systems; (3) principles of fluid power; (4) hydraulic and pneumatic drive systems; (5) wheel and…

  9. Book Review: It's Not You, It's the Dishes: How to Minimize Conflict and Maximize Happiness in Your Relationship

    Directory of Open Access Journals (Sweden)

    Derek Lawson

    2014-08-01

    Full Text Available It’s Not You, It’s The Dishes brings economic principles and theory into the married life of couples. The authors simplify economics by providing fundamental concepts while removing technical jargon in a funny, yet intuitive way. Readers are introduced to the basics of comparative advantage, game theory, and eight other economic principles, all while learning lessons on how to resourcefully allocate their limited units of time, money, and energy to yield a better return on their biggest investment of their lives, their marriage. At its core, this is a self-help book aimed at married couples. Nevertheless, financial professionals and academics may benefit from reading the book, particularly because it may be beneficial helping to brainstorm potential solutions with their clients or as “homework” for client couples.

  10. Experimental simulation of latent heat thermal energy storage and heat pipe thermal transport for dish concentrator solar receiver

    Science.gov (United States)

    Narayanan, R.; Zimmerman, W. F.; Poon, P. T. Y.

    1981-01-01

    Test results on a modular simulation of the thermal transport and heat storage characteristics of a heat pipe solar receiver (HPSR) with thermal energy storage (TES) are presented. The HPSR features a 15-25 kWe Stirling engine power conversion system at the focal point of a parabolic dish concentrator operating at 827 C. The system collects and retrieves solar heat with sodium pipes and stores the heat in NaF-MgF2 latent heat storage material. The trials were run with a single full scale heat pipe, three full scale TES containers, and an air-cooled heat extraction coil to replace the Stirling engine heat exchanger. Charging and discharging, constant temperature operation, mixed mode operation, thermal inertial, etc. were studied. The heat pipe performance was verified, as were the thermal energy storage and discharge rates and isothermal discharges.

  11. CONC/11: A computer program for calculating the performance of dish-type solar thermal collectors and power systems

    Science.gov (United States)

    Jaffe, L. D.

    1984-01-01

    The CONC/11 computer program designed for calculating the performance of dish-type solar thermal collectors and power systems is discussed. This program is intended to aid the system or collector designer in evaluating the performance to be expected with possible design alternatives. From design or test data on the characteristics of the various subsystems, CONC/11 calculates the efficiencies of the collector and the overall power system as functions of the receiver temperature for a specified insolation. If desired, CONC/11 will also determine the receiver aperture and the receiver temperature that will provide the highest efficiencies at a given insolation. The program handles both simple and compound concentrators. The CONC/11 is written in Athena Extended FORTRAN (similar to FORTRAN 77) to operate primarily in an interactive mode on a Sperry 1100/81 computer. It could also be used on many small computers. A user's manual is also provided for this program.

  12. CONC/11: a computer program for calculating the performance of dish-type solar thermal collectors and power systems

    Energy Technology Data Exchange (ETDEWEB)

    Jaffe, L. D.

    1984-02-15

    CONC/11 is a computer program designed for calculating the performance of dish-type solar thermal collectors and power systems. It is intended to aid the system or collector designer in evaluating the performance to be expected with possible design alternatives. From design or test data on the characteristics of the various subsystems, CONC/11 calculates the efficiencies of the collector and the overall power system as functions of the receiver temperature for a specified insolation. If desired, CONC/11 will also determine the receiver aperture and the receiver temperature that will provide the highest efficiencies at a given insolation. The program handles both simple and compound concentrators. CONC/11 is written in Athena Extended Fortran (similar to Fortran 77) to operate primarily in an interactive mode on a Sperry 1100/81 computer. It could also be used on many small computers.

  13. Directed midbrain and spinal cord neurogenesis from pluripotent stem cells to model development and disease in a dish

    Directory of Open Access Journals (Sweden)

    Ilary eAllodi

    2014-05-01

    Full Text Available Induction of specific neuronal fates is restricted in time and space in the developing CNS through integration of extrinsic morphogen signals and intrinsic determinants. Morphogens impose regional characteristics on neural progenitors in a concentration-dependent fashion and establish distinct progenitor domains. Such domains are defined by unique expression patterns of fate determining transcription factors. These processes of neuronal fate specification can be recapitulated in vitro using pluripotent stem cells. In this review, we focus on the generation of dopamine neurons and motor neurons, which are induced at ventral positions of the neural tube through Sonic hedgehog (Shh signaling, and defined at anteroposterior positions by fibroblast growth factor (Fgf 8, Wnt1, and retinoic acid (RA. In vitro utilization of these morphogenic signals typically results in the generation of multiple neuronal cell types, which are defined at the intersection of these signals. If the purpose of in vitro neurogenesis is to generate one cell type only, further lineage restriction can be accomplished by forced expression of specific transcription factors in a permissive environment. Alternatively, cell-sorting strategies allow for selection of neuronal progenitors or mature neurons. However, modeling development, disease and prospective therapies in a dish could benefit from structured heterogeneity, where desired neurons are appropriately synaptically connected and thus better reflect the three-dimensional structure of that region. By modulating the extrinsic environment to direct sequential generation of neural progenitors within a domain, followed by self-organization and synaptic establishment, a reductionist model of that brain region could be created. Here we review recent advances in neuronal fate induction in vitro, with a focus on the interplay between cell intrinsic and extrinsic factors, and discuss the implications for studying development and

  14. Preference and intake frequency of high sodium foods and dishes and their correlations with anthropometric measurements among Malaysian subjects.

    Science.gov (United States)

    Choong, Stella Sinn-Yee; Balan, Sumitha Nair; Chua, Leong-Siong; Say, Yee-How

    2012-06-01

    This study investigated the preference and intake frequency of a list of 15 commonly available high sodium Malaysian foods/dishes, discretionary salt use, and their possible association with demographics, blood pressures and anthropometric measurements among 300 Malaysian university students (114 males, 186 females; 259 ethnic Chinese, 41 Indians; 220 lean, 80 overweight). French fries and instant soup noodle were found to be the most preferred and most frequently consumed salty food, respectively, while salted fish was least preferred and least frequently consumed. Males had a significantly higher intake frequency of at least 6 of the salty foods, but the preference of most salty foods was not significantly different between genders. Ethnic Chinese significantly preferred more and took more frequently traditional and conventional Malaysian foods like asam laksa (a Malaysian salty-sour-spicy noodle in fish stock), salted biscuits and salted vegetable, while Indians have more affinity and frequency towards eating salty Western foods. Body Mass Index was significantly negatively correlated with the intake frequency of canned/packet soup and salted fish while waist circumference was significantly positively correlated with the preference of instant noodle. Also, an increased preference of potato chips and intake frequency of salted biscuits seemed to lead to a decreased WHR. Other than these, all the other overweight/obesity indicators did not seem to fully correlate with the salty food preference and intake frequency. Nevertheless, the preference and intake frequency of asam laksa seemed to be significant negative predictors for blood pressures. Finally, increased preference and intake frequency of high sodium shrimp paste (belacan)-based foods like asam laksa and belacan fried rice seemed to discourage discretionary salt use. In conclusion, the preference and intake frequency of the high sodium belacan-based dish asam laksa seems to be a good predictor for ethnic

  15. Formation flying within a constellation of nano-satellites the QB50 mission

    NARCIS (Netherlands)

    Gill, E.K.A.; Sundaramoorthy, P.; Bouwmeester, J.; Zandbergen, B.; Reinhard, R.

    2010-01-01

    QB50 is a mission establishing an international network of 50 nano-satellites for multi-point, in-situ measurements in the lower thermosphere and re-entry research. As part of the QB50 mission, the Delft University of Technology intends to contribute two nano-satellites both being equipped with a hi

  16. Mobile satellite communications handbook

    CERN Document Server

    Cochetti, Roger

    2014-01-01

    With a Preface by noted satellite scientist Dr. Ahmad Ghais, the Second Edition reflects the expanded user base for this technology by updating information on historic, current, and planned commercial and military satellite systems and by expanding sections that explain the technology for non-technical professionals.   The book begins with an introduction to satellite communications and goes on to provide an overview of the technologies involved in mobile satellite communications, providing basic introductions to RF Issues, power Issues, link issues and system issues. It describes

  17. Satellite communication antenna technology

    Science.gov (United States)

    Mittra, R. (Editor); Imbriale, W. A. (Editor); Maanders, E. J. (Editor)

    1983-01-01

    A general overview of current technology in the field of communication satellite antennas is presented. Among the topics discussed are: the design of multiple beam systems; frequency reuse; and polarization control of antenna measurements. Consideration is also given to: contour beam synthesis; dual shaped reflector synthesis; beam shaping; and offset reflector design. The applications of the above technologies to present and future generations of communications satellites is considered, with emphasis given to such systems as: the Intelsats; the Defense Satellite Communications System, (DSCS-III); Satellite Business System (SBS), and Comstar.

  18. Methods of satellite oceanography

    Science.gov (United States)

    Stewart, R. H.

    1985-01-01

    The theoretical basis for remote sensing measurements of climate and ocean dynamics is examined. Consideration is given to: the absorption of electromagnetic radiation in the atmosphere; scattering in the atmosphere; and satellite observations using visible light. Consideration is also given to: the theory of radio scatter from the sea; scatter of centimeter waves from the sea; and the theory of operation of synthetic aperture radars. Additional topics include: the coordinate systems of satellite orbits for oceanographic remote sensing applications; the operating features of the major U.S. satellite systems for viewing the ocean; and satellite altimetry.

  19. Dental operatory design and equipment.

    Science.gov (United States)

    Floyd, M

    1993-08-01

    Improving and expanding the dental services of a practice can involve purchasing new equipment and even modifying or expanding the physical plant. Operatory design is important to the efficiency with which dental procedures can be performed. Equipment purchases to outfit the dental operatory should be made based on the specific needs and functions of a practice.

  20. Information technology equipment cooling method

    Energy Technology Data Exchange (ETDEWEB)

    Schultz, Mark D.

    2015-10-20

    According to one embodiment, a system for removing heat from a rack of information technology equipment may include a sidecar indoor air to liquid heat exchanger that cools air utilized by the rack of information technology equipment to cool the rack of information technology equipment. The system may also include a liquid to liquid heat exchanger and an outdoor heat exchanger. The system may further include configurable pathways to connect and control fluid flow through the sidecar heat exchanger, the liquid to liquid heat exchanger, the rack of information technology equipment, and the outdoor heat exchanger based upon ambient temperature and/or ambient humidity to remove heat generated by the rack of information technology equipment.

  1. Aeration equipment for small depths

    Science.gov (United States)

    Sluše, Jan; Pochylý, František

    2015-05-01

    Deficit of air in water causes complications with cyanobacteria mainly in the summer months. Cyanobacteria is a bacteria that produces poison called cyanotoxin. When the concentration of cyanobacteria increases, the phenomena "algal bloom" appears, which is very toxic and may kill all the organisms. This article describes new equipment for aeration of water in dams, ponds and reservoirs with small depth. This equipment is mobile and it is able to work without any human factor because its control is provided by a GPS module. The main part of this equipment consists of a floating pump which pumps water from the surface. Another important part of this equipment is an aerator where water and air are blended. Final aeration process runs in the nozzles which provide movement of all this equipment and aeration of the water. Simulations of the flow are solved by multiphase flow with diffusion in open source program called OpenFOAM. Results will be verified by an experiment.

  2. An Overview of Dish-Stirling Concentrating Solar Power Technology%碟式斯特林太阳能热发电的技术发展

    Institute of Scientific and Technical Information of China (English)

    朱辰元; 彭小方

    2011-01-01

    The principle of Solar Dish-Stirling power system has been introduced.Some tests show that Solar Dish-Stirling technology has the highest solar energy-to-grid quality electricity transfer efficiency compared to peer technologies.Recent development of dish concentrating solar power systems based on Stirling engine technology has also been discussed.In view of the key technology of gas Stirling engine had been breached,a technical condition in developing 25kW dish-Stirling concentrating solar power in China has been formed.%碟式斯特林太阳能热发电是目前发电效率最高的太阳能热发电的技术。介绍了碟式斯特林太阳能热发电系统原理,论述了国际上目前以热气机为核心技术的碟式太阳能热发电系统发展状况。指出我国的燃气热气机发电技术已经取得了突破性的发展,25kW级碟式斯特林太阳能热发电系统的研发已具备了技术基础。

  3. Space Solar Power Satellite Systems, Modern Small Satellites, and Space Rectenna

    Science.gov (United States)

    Bergsrud, Corey Alexis Marvin

    Space solar power satellite (SSPS) systems is the concept of placing large satellite into geostationary Earth orbit (GEO) to harvest and convert massive amounts of solar energy into microwave energy, and to transmit the microwaves to a rectifying antenna (rectenna) array on Earth. The rectenna array captures and converts the microwave power into usable power that is injected into the terrestrial electric grid for use. This work approached the microwave power beam as an additional source of power (with solar) for lower orbiting satellites. Assuming the concept of retrodirectivity, a GEO-SSPS antenna array system tracks and delivers microwave power to lower orbiting satellites. The lower orbiting satellites are equipped with a stacked photovoltaic (PV)/rectenna array hybrid power generation unit (HPGU) in order to harvest solar and/or microwave energy for on-board use during orbit. The area, and mass of the PV array part of the HPGU was reduced at about 32% beginning-of-life power in order to achieve the spacecraft power requirements. The HPGU proved to offer a mass decrease in the PGU, and an increase in mission life due to longer living component life of the rectenna array. Moreover, greater mission flexibility is achieved through a track and power delivery concept. To validate the potential advantages offered by a HPGU, a mission concept was presented that utilizes modern small satellites as technology demonstrators. During launch, a smaller power receiving "daughter" satellite sits inside a larger power transmitting "mother" satellite. Once separated from the launch vehicle the daughter satellite is ejected away from the mother satellite, and each satellite deploys its respective power transmitting or power receiving hardware's for experimentation. The concept of close proximity mission operations between the satellites is considered. To validate the technology of the space rectenna array part of the HPGU, six milestones were completed in the design. The first

  4. Equipe de trabalho

    Directory of Open Access Journals (Sweden)

    Gabriel Gerber Hornink

    2014-08-01

    Full Text Available   Equipe de Trabalho 2014 1. Equipe editorial Editor-Chefe Bayardo Bapstista Torres, Instituto de Química - USP, Brasil Eduardo Galembeck, Departamento de Bioquímica Instituto de Biologia UNICAMP, Brasil   Editores Gabriel Gerber Hornink, Depto. Bioquímica, Instituto de Ciências Biomédicas, Universidade - Federal de Alfenas - Unifal-MG, Brasil Vera Maria Treis Trindade, Instituto de Ciências Básicas da Saúde, Departamento de Bioquímica, Universidade Federal do Rio Grande do Sul, Brasil   Corpo Editorial Adriana Cassina, Departamento de Bioquímica, Facultad de Medicina, Universidad de la República, Uruguai Angel Herráez, Departamento de Bioquímica y Biología molecular, Universidad de Alcalá de Henares, Madrid, Espanha André Amaral Gonçalves Bianco, Universidade Federal de São Paulo (Unifesp, Brasil Denise Vaz de Macedo, Departamento de Bioquímica, Instituto de Biologia, Universidade Estadual de Campinas - Unicamp, Brasil Eneida de Paula, Departamento de Bioquímica, Instituto de Biologia, Universidade Estadual de Campinas - Unicamp, Brasil Guilherme Andrade Marson, Instituto de Química - USP, Brasil Jose Antonio Martinez Oyanedel, Universidad de Concepción, Chile Josep Maria Fernández Novell, Dept. Bioquímica i Biologia Molecular Universitat de Barcelona, Espanha Leila Maria Beltramini, Instituto de Física de São Carlos, Universidade Estadual de São Paulo - USP, Brasil Manuel João da Costa, Escola de Ciências da Saúde, Universidade do Minho, Portugal Maria Lucia Bianconi, Instituto de Bioquímica Médica Universidade Federal do Rio de Janeiro (UFRJ, Brasil María Noel Alvarez, Departamento de Bioquímica, Facultad de Medicina, Universidad de la República, Uruguai Miguel Ángel Medina Torres, Department of Molecular Biology & Biochemistry Faculty of Sciences University of Málaga, Espanha Nelma Regina Segnini Bossolan, Instituto de Física de São Carlos, Universidade de São Paulo - USP, Brasil Paulo De Avila

  5. Effects on dynamic characters of antenna structures in satellite induced by disordered parameters

    Institute of Scientific and Technical Information of China (English)

    Liu Xiangqiu; Wang Cong; Wang Weiyuan; Zou Zhenzhu

    2009-01-01

    A simplified dynamic model of a dish antenna in satellite is established in this article. The model can be easily used to analyze the dynamic behaviour of the antenna structure. In terms of the simplified model, effects on dynamic characters due to the disorder of parameters are investigated in details. The frequencies calculated by the simplified model accord with those computed by ANSYS. Based on the mode shapes of disordered and perfect structure, the influence law and varying trend of dynamic characters of antenna structures in satellites produced by stiffness and mass of antenna ribs, stiffness of antenna membranes and angles between adjacent ribs, are obtained. The analyses in the paper indicate that the effects by disordered parameters can not be ignored in the dynamic analysis of such structures.

  6. Satellites of spiral galaxies

    Science.gov (United States)

    Zaritsky, Dennis; Smith, Rodney; Frenk, Carlos; White, Simon D. M.

    1993-01-01

    We present a survey of satellites around a homogeneous set of late-type spirals with luminosity similar to that of the Milky Way. On average, we find fewer than 1.5 satellites per primary, but we argue that we can treat the survey as an ensemble and so derive the properties of the halo of a 'typical' isolated spiral. The projected density profile of the ensemble falls off approximately as 1/r. Within 50 kpc the azimuthal distribution of satellites shows some evidence for the 'Holmberg effect', an excess near the minor axis of the primary; however, at larger projected distances, the distribution appears isotropic. There is a weak but significant correlation between the size of a satellite and its distance from its primary, as expected if satellites are tidally truncated. Neither Hubble type nor spectral characteristics correlate with apparent separation. The ensemble of satellites appears to be rotating at about 30 km/s in the same direction as the galactic disk. Satellites on prograde orbits tend to be brighter than those on retrograde orbits. The typical velocity difference between a satellite and its primary shows no clear dependence either on apparent separation, or on the rotation speed of the primary. Thus our survey demonstrates that isolated spiral galaxies have massive halos that extend to many optical radii.

  7. Communication satellite technology trends

    Science.gov (United States)

    Cuccia, Louis

    1986-01-01

    A chronology of space-Earth interconnectivity is presented. The Advanced Communications Technology Satellite (ACTS) system, Land Mobile Satellite, space-Earth antennas, impact of antenna size on coverage, intersatellite links are outlined. This presentation is represented by graphs and charts only.

  8. Association between Motives for Dish Choices during Home Meal Preparation and Weight Status in the NutriNet-Santé Study

    Directory of Open Access Journals (Sweden)

    Pauline Ducrot

    2016-07-01

    Full Text Available Although home cooking has been associated with a lower body mass index in a few studies, no data exists on the motives behind food dish choices during home meal preparation and on their association with overweight. This study aimed to evaluate this association in 50,003 participants from the NutriNet-Santé cohort. Dimensions underlying the importance of 27 criteria possibly influencing dish choices were determined using an exploratory factor analysis. The association between dish choice motives and overweight (including obesity was estimated using logistic regression models adjusted for sociodemographic and lifestyle characteristics. Five dimensions of dishes choice motives emerged: healthy diet (e.g., “nutritional balance of the dish”, constraints (e.g., “my cooking skills”, pleasure (e.g., “originality of the dish”, specific diets (e.g., “my health status”, and organization (e.g., “what I planned to eat”. A negative association was observed between the healthy diet factor and being overweight (OR = 0.65 (95% CI (confidence interval: 0.62–0.67, whereas a positive association appeared for factors regarding pleasure (OR = 1.14 (95% CI: 1.10–1.19 and specific diets (OR = 1.19 (95% CI: 1.17–1.22. No significant associations were observed for constraints and organization. The significant associations between dish choice motives and overweight suggested the interest of focusing on these motives in order to promote healthier food choices during home cooking.

  9. TRANSPORT AND EMPLACEMENT EQUIPMENT DESCRIPTIONS

    Energy Technology Data Exchange (ETDEWEB)

    NA

    1997-09-29

    The objective and the scope of this document are to list and briefly describe the major mobile equipment necessary for waste package (WP) Transport and Emplacement in the proposed subsurface nuclear waste repository at Yucca Mountain. Primary performance characteristics and some specialized design features of the equipment are explained and summarized in the individual subsections of this document. The Transport and Emplacement equipment described in this document consists of the following: (1) WP Transporter; (2) Reusable Rail Car; (3) Emplacement Gantry; (4) Gantry Carrier; and (5) Transport Locomotive.

  10. Sources of Error in Satellite Navigation Positioning

    Directory of Open Access Journals (Sweden)

    Jacek Januszewski

    2017-09-01

    Full Text Available An uninterrupted information about the user’s position can be obtained generally from satellite navigation system (SNS. At the time of this writing (January 2017 currently two global SNSs, GPS and GLONASS, are fully operational, two next, also global, Galileo and BeiDou are under construction. In each SNS the accuracy of the user’s position is affected by the three main factors: accuracy of each satellite position, accuracy of pseudorange measurement and satellite geometry. The user’s position error is a function of both the pseudorange error called UERE (User Equivalent Range Error and user/satellite geometry expressed by right Dilution Of Precision (DOP coefficient. This error is decomposed into two types of errors: the signal in space ranging error called URE (User Range Error and the user equipment error UEE. The detailed analyses of URE, UEE, UERE and DOP coefficients, and the changes of DOP coefficients in different days are presented in this paper.

  11. Delivery of satellite based broadband services

    Science.gov (United States)

    Chandrasekhar, M. G.; Venugopal, D.

    2007-06-01

    Availability of speedy communication links to individuals and organizations is essential to keep pace with the business and social requirements of this modern age. While the PCs have been continuously growing in processing speed and memory capabilities, the availability of broadband communication links still has not been satisfactory in many parts of the world. Recognizing the need to give fillip to the growth of broadband services and improve the broadband penetration, the telecom policies of different counties have placed special emphasis on the same. While emphasis is on the use of fiber optic and copper in local loop, satellite communications systems will play an important role in quickly establishing these services in areas where fiber and other communication systems are not available and are not likely to be available for a long time to come. To make satellite communication systems attractive for the wide spread of these services in a cost effective way special emphasis has to be given on factors affecting the cost of the bandwidth and the equipment. As broadband services are bandwidth demanding, use of bandwidth efficient modulation technique and suitable system architecture are some of the important aspects that need to be examined. Further there is a need to re-look on how information services are provided keeping in view the user requirements and broadcast capability of satellite systems over wide areas. This paper addresses some of the aspects of delivering broadband services via satellite taking Indian requirement as an example.

  12. Using PHM to measure equipment usable life on the Air Force's next generation reusable space booster

    Science.gov (United States)

    Blasdel, A.

    The U.S. Air Force procures many launch vehicles and launch vehicle services to place their satellites at their desired location in space. The equipment on-board these satellite and launch vehicle often suffer from premature failures that result in the total loss of the satellite or a shortened mission life sometimes requiring the purchase of a replacement satellite and launch vehicle. The Air Force uses its EELV to launch its high priority satellites. Due to a rise in the cost of purchasing a launch using the Air Force's EELV from 72M in 1997 to as high as 475M per launch today, the Air Force is working to replace the EELV with a reusable space booster (RSB). The RSB will be similar in design and operations to the recently cancelled NASA reusable space booster known as the Space Shuttle. If the Air Force uses the same process that procures the EELV and other launch vehicles and satellites, the RSB will also suffer from premature equipment failures thus putting the payloads at a similar high risk of mission failure. The RSB is expected to lower each launch cost by 50% compared to the EELV. The development of the RSB offers the Air Force an opportunity to use a new reliability paradigm that includes a prognostic and health management program and a condition-based maintenance program. These both require using intelligent, decision making self-prognostic equipment The prognostic and health management program and its condition-based maintenance program allows increases in RSB equipment usable life, lower logistics and maintenance costs, while increasing safety and mission assurance. The PHM removes many decisions from personnel that, in the past resulted in catastrophic failures and loss of life. Adding intelligent, decision-making self-prognostic equipment to the RSB will further decrease launch costs while decreasing risk and increasing safety and mission assurance.

  13. Beginnings of Satellite Navigation

    Directory of Open Access Journals (Sweden)

    Miljenko Solarić

    2008-05-01

    Full Text Available The first satellite navigation system called the Navy Navigation Satellite System (NNSS or TRANSIT was planned in the USA in 1958. It consisted of 5-6 artificial Earth satellites, was set in motion for the USA military in 1964, and in 1967 for civilian purposes. The frequency shift of received radio waves emitted from the satellite and caused by the Doppler effect was measured. The TRANSIT satellite speed of approaching or moving away was derived from that; the TRANSIT satellites emmited also their own coordinates. Then the ship's position was determined by an intersection of three hyperboloids, which were determined from differences of distances in three time intervals. Maintenance of this navigation system was stopped in 1996, but it is still being used in the USA Navy for exploring the ionosphere. Furthermore, results of Doppler measurements in international projects at the Hvar Observatory from 1982 and 1983. This was the first time in Croatia and the former country that the coordinates of the Hvar Observatory were determined in the unique world coordinate system WGS'72. The paper ends with a brief representation of the Tsiklon Doppler navigation system produced in the former Soviet Union, and there is a list of some of numerous produced and designed satellite navigation systems.Ključne riječi

  14. ENERGY STAR Certified Imaging Equipment

    Data.gov (United States)

    U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 2.0 ENERGY STAR Program Requirements for Imaging Equipment that are effective as of...

  15. EAS Equipment Authorization Grantee Registrations

    Data.gov (United States)

    Federal Communications Commission — EAS (Equipment Authorization System). Radio Frequency (RF) devices are required to be properly authorized under 47 CFR Part 2 prior to being marketed or imported...

  16. EMR Measurements on NDA Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Macdonell, Alexander Thomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Meierbachtol, Krista Cruse [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Evans, James Walter Jr. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Mayo, Douglas R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-07-10

    Electromagnetic radiation (EMR) emission strength measurements were performed on a suite of passive non-destructive assay (NDA) radiation detection equipment. Data were collected from 9 kHz up to 6 GHz on each of the assembled systems.

  17. Innovative Application of Maintenance-Free Phase-Change Thermal Energy Storage for Dish-Engine Solar Power Generation

    Energy Technology Data Exchange (ETDEWEB)

    Qui, Songgang [Temple University; Galbraith, Ross [Infinia

    2013-01-23

    This final report summarizes the final results of the Phase II Innovative Application of Maintenance-Free Phase-Change Thermal Energy Storage for Dish-Engine Solar Power Generation project being performed by Infinia Corporation for the U.S. Department of Energy under contract DE-FC36-08GO18157 during the project period of September 1, 2009 - August 30, 2012. The primary objective of this project is to demonstrate the practicality of integrating thermal energy storage (TES) modules, using a suitable thermal salt phase-change material (PCM) as its medium, with a dish/Stirling engine; enabling the system to operate during cloud transients and to provide dispatchable power for 4 to 6 hours after sunset. A laboratory prototype designed to provide 3 kW-h of net electrical output was constructed and tested at Infinia's Ogden Headquarters. In the course of the testing, it was determined that the system's heat pipe network - used to transfer incoming heat from the solar receiver to both the Stirling generator heater head and to the phase change salt - did not perform to expectations. The heat pipes had limited capacity to deliver sufficient heat energy to the generator and salt mass while in a charging mode, which was highly dependent on the orientation of the device (vertical versus horizontal). In addition, the TES system was only able to extract about 30 to 40% of the expected amount of energy from the phase change salt once it was fully molten. However, the use of heat pipes to transfer heat energy to and from a thermal energy storage medium is a key technical innovation, and the project team feels that the limitations of the current device could be greatly improved with further development. A detailed study of manufacturing costs using the prototype TES module as a basis indicates that meeting DOE LCOE goals with this hardware requires significant efforts. Improvement can be made by implementing aggressive cost-down initiatives in design and materials

  18. Military GPS User Equipment (MGUE)

    Science.gov (United States)

    2015-04-29

    Space and Missile Systems Center Military GPS User Equipment (MGUE) Lt Col James “Mutt” Wilson Program Manager 29 Apr 15 Information contained in...SUBTITLE Military GPS User Equipment (MGUE) 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK...SUPPLEMENTARY NOTES Presented at the GPS Partnership Council 2015 (GPSPC15), held April 29 to May 1, 2015, at the Los Angeles AFB, CA. 14. ABSTRACT

  19. Nuclear Weapon and Military Equipment

    Directory of Open Access Journals (Sweden)

    N. Natarajan

    1985-10-01

    Full Text Available Military equipment must survive a, nuclear attack if enough personnel required to operate them remain combat effective. To achieve this goal, the criteria that determine equipment survivability should be established and any new design should incorporate these criteria to evolve a hardened design. An analysis of the overall response by considering the response to each individual nuclear environment can result in a balanced overall hardened system. The paper discusses the criteria required to be known.

  20. Food Preparation Studies

    Science.gov (United States)

    1974-11-01

    dry mixing, melting ingre- dients such as butter or margarine or shortening, creaming butter or shortening, mixing and blending, dissolving soda in...cooked at the satellite and of various pasta and rice dishes. These latter dishes will require some baking, and, to avoid equip- ment duplication, they...Propeller mixers are made by many companies including Lightnin. · Steamed rice (E-5) and the pasta dishes require a jacketed kettle, preferably with a

  1. Research on Selection of Equipment Maintenance Modes

    Institute of Scientific and Technical Information of China (English)

    SHANG Wen-li; SHI Hai-bo; HE Bai-tao

    2006-01-01

    The development of equipment maintenance management is introduced, and equipment maintenance concept is defined. Equipment maintenance modes are classified, analyzed and compared, which merits and demerits are pointed out. At last, a decision-making frame to select equipment maintenance modes is advanced, and steps to select and implement equipment maintenance are given.

  2. 14 CFR 25.1415 - Ditching equipment.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Ditching equipment. 25.1415 Section 25.1415... STANDARDS: TRANSPORT CATEGORY AIRPLANES Equipment Safety Equipment § 25.1415 Ditching equipment. (a) Ditching equipment used in airplanes to be certificated for ditching under § 25.801, and required by...

  3. An Image-Based Sensor System for Autonomous Rendez-Vous with Uncooperative Satellites

    CERN Document Server

    Miravet, Carlos; Krouch, Eloise; del Cura, Juan Manuel

    2008-01-01

    In this paper are described the image processing algorithms developed by SENER, Ingenieria y Sistemas to cope with the problem of image-based, autonomous rendez-vous (RV) with an orbiting satellite. The methods developed have a direct application in the OLEV (Orbital Life Extension Extension Vehicle) mission. OLEV is a commercial mission under development by a consortium formed by Swedish Space Corporation, Kayser-Threde and SENER, aimed to extend the operational life of geostationary telecommunication satellites by supplying them control, navigation and guidance services. OLEV is planned to use a set of cameras to determine the angular position and distance to the client satellite during the complete phases of rendez-vous and docking, thus enabling the operation with satellites not equipped with any specific navigational aid to provide support during the approach. The ability to operate with un-equipped client satellites significantly expands the range of applicability of the system under development, compar...

  4. Liquid dish washing soap: An excellent substitute for xylene and alcohol in hematoxylin and eosin staining procedure

    Directory of Open Access Journals (Sweden)

    Surekha Ramulu

    2012-01-01

    Full Text Available Aims: Liquid dish washing solution (DWS was used as a substitute for xylene to dewax tissue sections during hematoxylin and eosin (H and E staining. The aim was to test and compare the hypothesis that xylene-ethanol free (XEF sections deparaffinized with diluted DWS are better than or at par with the conventional H and E sections. Materials and Methods: Fifty paraffin-embedded tissue blocks was included. One section was stained with conventional HandE (group A and the other with XEF HandE (group B staining method. Slides were scored for parameters: nuclear, cytoplasmic, clarity, uniformity, and crispness of staining. Z test was used for statistical analysis. For accuracy of diagnosis, sensitivity, specificity, positive predictive value, and negative predictive value were tested. Results: Adequate nuclear staining was noted in 94% in group A and 96% in group B, -adequate cytoplasmic staining in 92% in group A and 86% in group B, clarity in 94% of group A and 96% of group B sections, uniform staining in 92% of group A and 80% of group B sections, crisp stain in 96% of group A and 88% of group B sections, and 94% of group A sections stained adequately for diagnosis as compared with 90% in group B sections. Conclusion: Liquid DWS can be used as an alternative and effective substitute to xylene and ethanol in routine HandE staining procedure.

  5. Effect of lime juice on Vibrio parahaemolyticus and Salmonella enterica inactivation during the preparation of the raw fish dish ceviche.

    Science.gov (United States)

    Mathurand, Prateek; Schaffner, Donald W

    2013-06-01

    Ceviche is a raw fish dish common in Peru and other Latin American counties. The most characteristic feature of ceviche is the use of lime juice for marinating or "cooking" the raw fish. Confirmed cases of cholera in Peru, New Jersey, and Florida have been associated with ceviche. Although the effect of organic acids on pathogenic bacteria has been well characterized, few data exist on the effect of these acids in seafood systems. The objective of the study was to evaluate the effects of lime juice marination on pathogens likely to be present in ceviche. Tilapia (Oreochromis niloticus) fillet pieces were inoculated with Vibrio parahaemolyticus and Salmonella enterica (>7 log CFU/g) and incubated at 25 and 4°C for 30 or 120 min in the presence of fresh lime juice at concentrations typical for the preparation of ceviche. Similar levels of cells were also inoculated into fresh lime juice without tilapia. Surviving cells were enumerated on selective (xylose lysine Tergitol 4 and thiosulfate-bile-citrate-sucrose) and nonselective (tryptic soy agar) media. V. parahaemolyticus levels were reduced to below detection limits (∼5-log reduction) under all conditions studied. Salmonella strains on tilapia were much more resistant to inactivation and were only slightly reduced (∼1- to 2-log reduction). Salmonella and V. parahaemolyticus inoculated directly into lime juice without tilapia were all reduced to below detection limits (∼5-log reduction). A typical ceviche recipe reduces V. parahaemolyticus risk significantly but is less effective for control of S. enterica.

  6. Hydrophilic group formation and cell culturing on polystyrene Petri-dish modified by ion-assisted reaction

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ki-Hwan E-mail: hama@kist.re.kr; Cho, Jun-Sik; Choi, Doo-Jin; Koh, Seok-Keun

    2001-04-01

    Polystyrene (PS) Petri-dishes were modified by an ion-assisted reaction (IAR) to improve wettability and to supply a suitable surface for cell culturing. Low energy Ar{sup +} ions with 1000 eV were irradiated on the surface of PS in oxygen gas environment. Water contact angles of PS were not reduced much by ion irradiation without oxygen gas and had a value of 40 deg. In the case of ion irradiation with flowing oxygen gas, however, the water contact angles were dropped significantly from 73 deg. to 19 deg. X-ray photoelectron spectroscopy analysis showed that the hydrophilic groups were formed on the surface of PS by a chemical reaction between unstable chains induced by ion irradiation and the oxygen gas. Newly formed hydrophilic groups were identified as -(C-O)-, -(C=O)- and -(C=O)-O- bonds. The influence of the surface modification on growth of the rat pheochromocytoma (PC12) cells was investigated. The IAR-treated PS surfaces showed enhanced attachment and growth in PC12 cell culture test.

  7. Sensitive voltammetric determination of lead released from ceramic dishes by using of bismuth nanostructures anchored on biochar.

    Science.gov (United States)

    Agustini, Deonir; Mangrich, Antonio Salvio; Bergamini, Márcio F; Marcolino-Junior, Luiz Humberto

    2015-09-01

    A simple and sensitive electroanalytical method was developed for determination of nanomolar levels of Pb(II) based on the voltammetric stripping response at a carbon paste electrode modified with biochar (a special charcoal) and bismuth nanostructures (nBi-BchCPE). The proposed methodology was based on spontaneous interactions between the highly functionalized biochar surface and Pb(II) ions followed by reduction of these ions into bismuth nanodots which promote an improvement on the stripping anodic current. The experimental procedure could be summarized in three steps: including an open circuit pre-concentration, reduction of accumulated lead ions at the electrode surface and stripping step under differential pulse voltammetric conditions (DPAdSV). SEM images revealed dimensions of bismuth nanodots ranging from 20 nm to 70 nm. The effects of main parameters related to biochar, bismuth and operational parameters were examined in detail. Under the optimal conditions, the proposed sensor has exhibited linear range from 5.0 to 1000 nmol L(-1) and detection limit of 1.41 nmol L(-1) for Pb(II). The optimized method was successfully applied for determination of Pb(II) released from overglaze-decorated ceramic dishes. Results obtained were compared with those given by inductively coupled plasma optical emission spectroscopy (ICP-OES) and they are in agreement at 99% of confidence level. Copyright © 2015. Published by Elsevier B.V.

  8. Performance analysis of dish solar stirling power system; Stirling engine wo mochiita taiyonetsu hatsuden system no seino yosoku

    Energy Technology Data Exchange (ETDEWEB)

    Tsuchiya, K.; Yamaguchi, I. [Meiji University, Tokyo (Japan); Naito, Y.; Momose, Y. [Aisin Seiki Co. Ltd., Aichi (Japan)

    1996-10-27

    In order to estimate the performance of the dish solar Stirling power system, matching and control of each component system were studied, and the performance of the 25kWe class power system was estimated on the basis of direct solar radiation measured in Miyako island, Okinawa. Application of a Stirling engine to solar heat power generation is highly effective in spite of its small scale. The total system is composed of a converging system, heat receiver, engine/generator system and control system. As the simulation result, the generator output is nearly proportional to direct solar radiation, and the system efficiency approaches to a certain constant value with an increase in direct solar radiation. As accumulated solar radiation is large, the influence of slope error of the converging mirror is comparatively small. The optimum aperture opening ratio of the heat receiver determined on the basis of mean direct solar radiation (accumulated solar radiation/{Delta}t (simulated operation time of the system)), corresponds to the primary approximation of the opening ratio for a maximum total generated output under variable direct solar radiation. 6 refs., 6 figs., 1 tab.

  9. Trends In Satellite Communication

    Science.gov (United States)

    Poley, William A.; Stevens, Grady H.; Stevenson, Steven M.; Lekan, Jack; Arth, Clifford H.; Hollansworth, James E.; Miller, Edward F.

    1988-01-01

    Report assesses trends in satellite communication from present to year 2010. Examines restrictions imposed by limited spectrum resource and technology needs created by trends. Personal communications, orbiting switchboards, and videophones foreseen.

  10. Domestic Communication Satellites

    Science.gov (United States)

    Horowitz, Andrew

    1974-01-01

    A discussion of the Federal Communications Commission's new policy on domestic satellites in light of our 1) military and economic history; 2) corporate interests; 3) citizen surveillance; and 4) media control. (HB)

  11. Handbook of satellite applications

    CERN Document Server

    Madry, Scott; Camacho-Lara, Sergio

    2013-01-01

    Top space experts from around the world have collaborated to produce this comprehensive, authoritative, and clearly illustrated reference guide to the fast growing, multi-billion dollar field of satellite applications and space communications. This handbook, done under the auspices of the International Space University based in France, addresses not only system technologies but also examines market dynamics, technical standards and regulatory constraints. The handbook is a completely multi-disciplinary reference book that covers, in an in-depth fashion, the fields of satellite telecommunications, Earth observation, remote sensing, satellite navigation, geographical information systems, and geosynchronous meteorological systems. It covers current practices and designs as well as advanced concepts and future systems. It provides a comparative analysis of the common technologies and design elements for satellite application bus structures, thermal controls, power systems, stabilization techniques, telemetry, com...

  12. Biological satellite Kosmos-936

    Science.gov (United States)

    Vedeshin, L. A.

    1978-01-01

    A description is given of physiological experiments performed on the biological satellite Kosmos-936. Other experiments to determine the electrostatic and dielectric responses to the effects of cosmic radiation are discussed.

  13. Small Satellite Transporter Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The primary objective is to determine whether this small satellite transporter is capable of transporting at least four 6U CubeSats is possible for a given set of...

  14. Monitoring of the orbital position of a geostationary satellite by the spatially separated reception of signals of digital satellite television

    Science.gov (United States)

    Kaliuzny, M. P.; Bushuev, F. I.; Sibiriakova, Ye. S.; Shulga, O. V.; Shakun, L. S.; Bezrukovs, V.; Kulishenko, V. F.; Moskalenko, S. S.; Malynovsky, Ye. V.; Balagura, O. A.

    2017-02-01

    The results of the determination of the geostationary satellite "Eutelsat-13B" orbital position obtained during 2015-2016 years using European stations' network for reception of DVB-S signals from the satellite are presented. The network consists of five stations located in Ukraine and Latvia. The stations are equipped with a radio engineering complex developed by the RI "MAO". The measured parameter is a time difference of arrival (TDOA) of the DVB-S signals to the stations of the network. The errors of TDOA determination and satellite coordinates, obtained using a numerical model of satellite motion, are equal ±2.6 m and ±35 m respectively. Software implementation of the numerical model is taken from the free space dynamics library OREKIT.

  15. 47 CFR 80.1087 - Ship radio equipment-Sea area A1.

    Science.gov (United States)

    2010-10-01

    ... which the ship is normally navigated, operating either: (1) On VHF using DSC; or (2) Through the polar... MF using DSC if the ship is engaged on voyages within coverage of MF coast stations equipped with DSC; or (4) On HF using DSC; or (5) Through the INMARSAT geostationary satellite service if...

  16. DFH-3 Satellite Platform

    Institute of Scientific and Technical Information of China (English)

    RenShufang

    2005-01-01

    The DFH-3 satellite platform is designed and developed by China Academy of Space Technology (CAST). It is a medium capability communications satellite platform. The platform adopts threeaxis attitude stabilization control system, having solar array output power of 1.7kW by the end of its design lifetime of 8 years. Its mass is 2100kg with payload capacity of 220kg.

  17. The Archimedes satellite system

    Science.gov (United States)

    Taylor, Stuart C.; Shurvinton, William D.

    1992-03-01

    Archimedes is a satellite system conceived by the European Space Agency (ESA) to effectively serve the European market for Mobile Radio Services (MRS). This paper describes the requirements and technical design of the Archimedes satellite system. The underlying assumptions and trade-offs behind the design are detailed and the design is compared and contrasted against alternative design solutions, both technically and economically. A path forward for the development of the system is indicated.

  18. ASTRID II satellit projekt

    DEFF Research Database (Denmark)

    Jørgensen, John Leif; Primdahl, Fritz

    1997-01-01

    The report describes the instruments developed for the Swedish micro satellite "ASTRID II". Specifications of the two instruments realized under this contract, a Stellar Compass and a CSC magnetometer are given follwed by a description of the project status and plan.......The report describes the instruments developed for the Swedish micro satellite "ASTRID II". Specifications of the two instruments realized under this contract, a Stellar Compass and a CSC magnetometer are given follwed by a description of the project status and plan....

  19. Need for, and financial feasibility of, satellite-aided land mobile communications

    Science.gov (United States)

    Castruccio, P. A.; Marantz, C. S.; Freibaum, J.

    Questions regarding the role of a mobile-satellite system in augmenting the terrestrial communications system are considered, and a market assessment study is discussed. Aspects of an investment analysis are examined, taking into account a three phase financial study of four postulated land Mobile Satellite Service (LMSS) systems, project profitability evaluation methods, risk analysis methods, financial projections, potential investor acceptance standards, and a risk analysis. It is concluded that a satellite augmented terrestrial mobile service appears to be economically and technically superior to a service depending exclusively on terrestrial systems. The interest in the Mobile Satellite Service is found to be worldwide, and the ground equipment market is potentially large.

  20. Global tracking and inventory of military hardware via LEO satellite: A system approach and likely scenario

    Science.gov (United States)

    Bell, David; Estabrook, Polly; Romer, Richard

    1995-01-01

    A system for global inventory control of electronically tagged military hardware is achievable using a LEO satellite constellation. An equipment Tag can communicate directly to the satellite with a power of 5 watts or less at a data rate of 2400 to 50,000 bps. As examples, two proposed commercial LEO systems, IRIDIUM and ORBCOMM, are both capable of providing global coverage but with dramatically different telecom capacities. Investigation of these two LEO systems as applied to the Tag scenario provides insight into satellite design trade-offs, constellation trade-offs and signal dynamics that effect the performance of a satellite-based global inventory control system.

  1. Satellite formation. II

    Science.gov (United States)

    Harris, A. W.

    1978-01-01

    A satellite formation model is extended to include evolution of planetary ring material and elliptic orbital motion. In this model the formation of the moon begins at a later time in the growth of the earth, and a significant fraction of the lunar material is processed through a circumterrestrial debris cloud where volatiles might have been lost. Thus, the chemical differences between the earth and moon are more plausibly accounted for. Satellites of the outer planets probably formed in large numbers throughout the growth of those planets. Because of rapid inward evolution of the orbits of small satellites, the present satellite systems represent only satellites formed in the last few percent of the growths of their primaries. The rings of Saturn and Uranus are most plausibly explained as the debris of satellites disrupted within the Roche limit. Because such a ring would collapse onto the planet in the course of any significant further accretion by the planet, the rings must have formed very near or even after the conclusion of accretion.

  2. CHINA LAUNCHES NEW SCIENTIFIC SATELLITE

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    China on Sept. 27, 2004 launched a scientific satellite atop a Long March 2D carrier rocket from Jiuquan Satellite Launch Center in Gansu province. 10 minutes after the launch, the satellite entered a preset orbit and is running sound at the orbit. It is the 20th recoverable satellite for scientific and technological

  3. A compact and low cost TT&C S-Band Ground Station for low orbit satellites

    Science.gov (United States)

    Pacola, Luiz C.; Ferrari, Carlos A.

    Instituto Nacional de Pesquisas Espaciais (INPE's) S-Band Ground Station for satellite control and monitoring is revised consdiering the current software and hardware technology. A Ground Station concept for low orbit satellites is presented. The front-end uses a small antenna and low cost associated equipment without loss of performance. The baseband equipment is highly standardized and developed on a personal computer IBM compatible using extensively Digital Signal Processing (DSP). A link budget for ranging, telecommand and telemetry is also presented.

  4. CERN lifting equipment use authorisation

    CERN Multimedia

    2004-01-01

    Updated procedures to obtain authorisation to use lifting equipment at CERN have been put in place. As a general rule, lifting equipment at CERN may be operated only by qualified staff, i.e. those who have had intensive training in and adequate experience of using such equipment. However, for straightforward recurrent lifting operations, the Organization issues authorisations to operate lifting equipment at CERN to people who have followed a suitable course of training. The authorisation to use lifting equipment is valid for five years. More information about the procedures will be found at the following addresses: CERN Staff: http://sc-gs.web.cern.ch/sc-gs/gs_ms/ms/freq%20topics/te_mc_FT_staff.htm Associated members of the personnel (users, ...) : http://sc-gs.web.cern.ch/sc-gs/gs_ms/ms/freq%20topics/te_mc_FT_users.htm Contractors personnel : http://sc-gs.web.cern.ch/sc-gs/gs_ms/ms/freq%20topics/te_mc_FT_peoplefromext.htm In case of questions, please send a message to: securite...

  5. Mining equipment manufacturers; 17th ed.

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    The report analyses and compares the financial ratios of mining equipment manufacturers in the United Kingdom. It includes companies who produce equipment for the mining industry such as cutting tools, drilling equipment, crushers, screens, centrifuges, tunnelling equipment, conveyors and other materials handling equipment, hydraulic equipment, filtration, pumping, and mixing equipment and ventilation equipment. The report presents business ratios analysing profitability, efficiency, liquidity, employee-based ratios and a series of figures on growth rate. Accounting data for the individual companies are given, together with principal ratios, areas of activity, names of directors and company secretary, trading address and holding companies.

  6. Mining equipment manufacturers. 13th edition

    Energy Technology Data Exchange (ETDEWEB)

    1992-01-01

    The report analyses and compares the financial ratios of mining equipment manufacturers in the United Kingdom. It includes companies who produce equipment for the mining industry such as cutting tools, drilling equipment, crushers, screens, centrifuges, tunnelling equipment, conveyors and other materials handling equipment, hydraulic equipment, filtration, pumping and mixing equipment and ventilation equipment. The report presents business ratios analysing profitability, efficiency, liquidity, employee-based ratios and a series of figures on growth rate. Accounting data for the individual companies are given, together with principal ratios, areas of activity, names of directors and company secretary, trading address and holding companies.

  7. Aerodynamics Laboratory Facilities, Equipment, and Capabilities

    Data.gov (United States)

    Federal Laboratory Consortium — The following facilities, equipment, and capabilities are available in the Aerodynamics Laboratory Facilities and Equipment (1) Subsonic, open-jet wind tunnel with...

  8. The Role and Position of Changshu Steamed Dish%常熟蒸菜在宴席团餐中的作用和地位

    Institute of Scientific and Technical Information of China (English)

    石庆; 陈建平

    2016-01-01

    Changshu’s steamed dish has a long history. In this paper all the narration is focused on the history of steamed dish, the principle of choosing ingredients, the nutrition and hygiene protection. The Aim is to give a suggestion for the healthy diet and the way to get more effciency and more nutritious by improving the cooking process.%常熟蒸菜由来已久,本文就蒸菜的历史由来、选料原则及营养卫生等方面进行阐述,通过改善工艺流程来提高效率,并能最大化的保留营养素,对人们的膳食提出指导意见。

  9. Viable metacercariae of Opisthorchis viverrini in northeastern Thai cyprinid fish dishes--as part of a rational program for control of O. viverrini-associated cholangiocarcinoma.

    Science.gov (United States)

    Prasongwatana, Jiraporn; Laummaunwai, Porntip; Boonmars, Thidarut; Pinlaor, Somchai

    2013-03-01

    Among the various types of chronic helminthic infections, only schistosomiasis hematobium, opisthorchiasis, and clonorchiasis in a long-standing inflammation are found to be causative agents of cancer. Opisthorchiasis and Opisthorchis viverrini-associated bile duct cancer are prevalent among the residents in northeastern Thailand, who prefer consuming raw or improperly cooked cyprinid fish. Although numerous studies have reported on the presence of O. viverrini metacercariae in freshwater cyprinid fishes, none of the data has been derived directly from cyprinid fish dishes. Here, we have demonstrated the presence of viable metacercariae in a number of cyprinid fish dishes that are among the favorite foods of northeastern Thais. Traditional salt-fermented and grilled cyprinid fish were found to be safe to consume, but not raw fish salad or cyprinid fish fermented in sticky rice for 69 h. This information could be used as part of a rational and sustainable control program for O. viverrini-associated bile duct cancer.

  10. The dish-Rankine SCSTPE program (Engineering Experiment no. 1). [systems engineering and economic analysis for a small community solar thermal electric system

    Science.gov (United States)

    Pons, R. L.; Grigsby, C. E.

    1980-01-01

    Activities planned for phase 2 Of the Small Community Solar Thermal Power Experiment (PFDR) program are summarized with emphasis on a dish-Rankine point focusing distributed receiver solar thermal electric system. Major design efforts include: (1) development of an advanced concept indirect-heated receiver;(2) development of hardware and software for a totally unmanned power plant control system; (3) implementation of a hybrid digital simulator which will validate plant operation prior to field testing; and (4) the acquisition of an efficient organic Rankine cycle power conversion unit. Preliminary performance analyses indicate that a mass-produced dish-Rankine PFDR system is potentially capable of producing electricity at a levelized busbar energy cost of 60 to 70 mills per KWh and with a capital cost of about $1300 per KW.

  11. Satellite Communications for ATM

    Science.gov (United States)

    Shamma, Mohammed A.

    2003-01-01

    This presentation is an overview on Satellite Communication for the Aeronautical Telecommunication Management (ATM) research. Satellite Communications are being considered by the FAA and NASA as a possible alternative to the present and future ground systems supporting Air Traffic Communications. The international Civil Aviation Organization (ICAO) have in place Standards and Recommended Practices (SARPS) for the Aeronautical Mobile Satellite Services (AMSS) which is mainly derived from the pre-existing Inmarsat service that has been in service since the 1980s. The Working Group A of the Aeronautical Mobile Communication Panel of ICAO has also been investigating SARPS for what is called the Next Generation Satellite Service (NGSS) which conforms less to the Inmarsat based architecture and explores wider options in terms of satellite architectures. Several designs are being proposed by Firms such as Boeing, ESA, NASA that are geared toward full or secondary usage of satellite communications for ATM. Satellite communications for ATM can serve several purposes ranging from primary usage where ground services would play a minimal backup role, to an integrated solution where it will be used to cover services, or areas that are less likely to be supported by the proposed and existing ground infrastructure. Such Integrated roles can include usage of satellite communications for oceanic and remote land areas for example. It also can include relieving the capacity of the ground network by providing broadcast based services of Traffic Information Services messages (TIS-B), or Flight Information Services (FIS-B) which can take a significant portion of the ground system capacity. Additionally, satellite communication can play a backup role to support any needs for ground replacement, or additional needed capacity even after the new digital systems are in place. The additional bandwidth that can be provided via satellite communications can also open the door for many new

  12. Experimental Satellite 2 Successfully Launched

    Institute of Scientific and Technical Information of China (English)

    LiuJie

    2004-01-01

    Small satellite Experimental Satellite 2 (SY-2) was launched by LM-2C launch vehicle from Xichang Satellite Launch Center on Nov. 18, 2004. Later the satellite entered the preset sun-synchronous orbit, which is 700 kilometers above the earth. The launch was the eighthmission this year by China Aerospace Science and Technology Corporation(CASC), which aims to test the technology of the satellite, conduct survey and monitoring of the land and resources and geographical environment on a trial basis.

  13. China's Meteorological Satellite Application System

    Institute of Scientific and Technical Information of China (English)

    Zhang Jiashen

    2008-01-01

    @@ China's meteorological satellite program consists of five systems,namely the satellite system,the launch vehicle system,the launch center system,TT&C and the ground application system.The satellite system consists of FengYun (FY) polar orbiting series and FY geostationary series,which are launched by LM launch vehicles from Taiyan Satellite Launch Center (TSLC) and Xichang Satellite Launch Center (XSLC) respectively.

  14. 衡阳市市售凉拌菜的卫生微生物质量监测%Microorganism monitoring among the Cold dishes in Hengyang

    Institute of Scientific and Technical Information of China (English)

    陶玲; 刘晓黎; 肖双; 周艺; 杨赟; 陈丽丽

    2011-01-01

    目的:了解衡阳市凉拌菜的总体微生物污染状况.方法:在2010年9月-2010年12月从超市、菜市场以及路边小摊采集各种凉拌菜,按照GB 4789-2010的方法检测.各指标参照国家标准GB2726-2005进行结果评价.结果:共检测400份凉拌菜,160份样品菌落总数超标,176份样品大肠菌群数超标,66份检出沙门菌;90份检出金黄色葡萄球菌;24份检出志贺菌.5种类型凉拌菜中,以豆制品的污染率最高.结论:本市凉拌菜的微生物污染较为严重.%Objective; To investigate the microbial contamination situation of the Cold dishes in Hengyang. Methods; Cold dishes samples were randomly collected from roadside store or supermarkets in Hengyang. Aerobic plate count, coliforms, Salmonella, Shigella and Staphylococcus aureus were detected according to the Food microbiological examination GB 4789 -2010. The results were analysed in accordance with the national standard GB 2726 -2005. Results; Among the 400 samples, aerobic plate count in 160 samples and coliforms in 176 samples were higher than the limit of the national standard. There were 66 strains of Salmonella, 90 strains of Staphylococcus aureus and 24 strains of Shigella isolated from these collected cold dishes. Among all the five kinds of samples, bean products were contaminated much seriously. Conclusion; The cold dishes in Hengyang existed serious contamination.

  15. Associations between motives for dish choice during home-meal preparation and diet quality in French adults: findings from the NutriNet-Santé study.

    Science.gov (United States)

    Ducrot, Pauline; Méjean, Caroline; Fassier, Philippine; Allès, Benjamin; Hercberg, Serge; Péneau, Sandrine

    2017-03-01

    A number of motives such as constraints or pleasure have been suggested to influence dish choices during home-meal preparation. However, no study has evaluated how the importance conferred to these motives potentially influence diet quality. The present study aims at investigating the difference in diet quality according to the importance attached by individuals to various dish choice motives. The importance of twenty-seven criteria related to dish choices on weekdays was evaluated among 48 010 French adults from the NutriNet-Santé study. ANCOVA and logistic regression models, adjusted for sociodemographic and lifestyle factors, were used to evaluate the association between the importance attached to dish choice motives (yes v. no) and energy and food group intakes, as well as adherence to French nutritional guidelines (modified Programme National Nutrition Santé-Guideline Score (mPNNS-GS)). A higher adherence to nutritional guidelines was observed in individuals attaching importance to a healthy diet (mPNNS-GS score 7·87 (sd 0·09) v. 7·39 (sd 0·09)) and specific diets (mPNNS-GS score 7·73 (sd 0·09) v. 7·53 (sd 0·09)), compared with those who attached little/no importance (all Pfoods compared with their respective counterparts (all P<0·0001). For other motives, that is, constraints, pleasure and organisation, only small differences were observed. The main difference in diet quality was related to the importance placed on a healthy diet. Although a causal link should be demonstrated, our findings suggested that strategies aiming at enabling people to take into account diet quality during home-meal preparation might be effective levers to promote healthy eating.

  16. MULTIDISCIPLINARIDADE E TRABALHO EM EQUIPE

    Directory of Open Access Journals (Sweden)

    Helmuth Krüger

    2013-10-01

    Full Text Available Foram dois os objetivos deste trabalho: estabelecer critérios para a comparação de pesquisas científicas e analisar alguns problemas psicossociais que podem ocorrer em equipes multiprofissionais. Conclui-se que os critérios de comparação podem ser os quatro componentes de qualquer disciplina científica: o conjunto dos pressupostos filosóficos, o objeto a investigar, a metodologia de pesquisa e a linguagem técnica empregada na elaboração de teorias. Quanto às equipes multiprofissionais, foram analisados 3 problemas: a atribuição de papéis sociais, a confidencialidade das informações e as diferenças de prestígio social entre os membros dessas equipes.

  17. Another donation of computer equipment

    CERN Multimedia

    Anaïs Schaeffer

    2014-01-01

    On Thursday 27 February, CERN was pleased to donate computer equipment to a physics institute in the Philippines.   H.E. Leslie J. Baja and Rolf Heuer. Following donations of computer equipment to institutes in Morocco, Ghana, Bulgaria, Serbia and Egypt, CERN is to send 50 servers and 4 network switches to the National Institute of Physics at the University of the Philippines Diliman. CERN’s Director-General Rolf Heuer and the Ambassador of the Philippines to Switzerland and Lichtenstein, H.E. Leslie J. Baja, spoke of their enthusiasm for the project during an official ceremony. The equipment will be used for various high energy physics research programmes in the Philippines and for the University’s development of digital resources for science.

  18. Flavor-enhancing properties of mushrooms in meat-based dishes in which sodium has been reduced and meat has been partially substituted with mushrooms.

    Science.gov (United States)

    Myrdal Miller, A; Mills, K; Wong, T; Drescher, G; Lee, S M; Sirimuangmoon, C; Schaefer, S; Langstaff, S; Minor, B; Guinard, J-X

    2014-09-01

    The effects of beef substitution with crimini or white mushrooms (Agaricus bisporus) on the flavor profiles of carne asada and beef taco blends were measured with a descriptive analysis panel. Sensory mitigation of sodium reduction through the incorporation of mushrooms was also investigated in the taco blends. The substitution of beef with mushrooms in the carne asada did not alter the overall flavor strength of the dish, but the incorporation of 50% or 80% ground mushroom in the beef taco blend did enhance its overall flavor as well as mushroom, veggie, onion, garlic and earthy flavors, and umami and sweet tastes. Overall flavor intensity of the 25% reduced-salt version of the 80% mushroom taco blend matched that of the full-salt versions of the 100% and 50% beef formulations, thus indicating that the substitution of 80% of the meat with mushrooms did mitigate the 25% sodium reduction in terms of the overall flavor impact of the dish, even if it did not quite compensate for the reduction in salty taste. This proof-of-concept study for the Healthy Flavors Research Initiative indicates that because of their flavor-enhancing umami principles, mushrooms can be used as a healthy substitute for meat and a mitigating agent for sodium reduction in meat-based dishes without loss of overall flavor. © 2014 Institute of Food Technologists®

  19. 聚光碟系统对焦斑直径的影响分析%Concentrating Dish System's Impact Analysis on Focal Spot Diameter

    Institute of Scientific and Technical Information of China (English)

    梁伟青; 朱辰元; 金永星; 周建明; 范伟成

    2015-01-01

    The article analyzes concentrating dish impact factors on focal spot diameter and validates results through experiments based on it. It analyzes concentrating dish manufacturing process, tracking precision, installation adjustment and wind-resistant ability impact on focal spot diameter of concentrating dish. Those impact factor analysis could provide coupling design and manufacturing process improvement of concentrating disk and receiver with necessary solid support and basis.%分析聚光碟对焦斑直径的影响因素,并通过试验加以验证。分析发现聚光碟的制造工艺、跟踪精度、安装后的调整、聚光碟的抗风能力等都会对聚光碟的焦斑直径产生影响。影响因素的分析可以为聚光碟和接收器的耦合设计以及聚光碟制造工艺的改进提供必要的依据。

  20. Prevalence and levels of Bacillus cereus emetic toxin in rice dishes randomly collected from restaurants and comparison with the levels measured in a recent foodborne outbreak.

    Science.gov (United States)

    Delbrassinne, Laurence; Andjelkovic, Mirjana; Dierick, Katelijne; Denayer, Sarah; Mahillon, Jacques; Van Loco, Joris

    2012-09-01

    Whereas the prevalence of Bacillus cereus emetic strains in the environment has been shown to be very low, there is a lack of information on the prevalence of its toxin, cereulide, in food. Yet, the rice leftovers of a family outbreak which occurred after the consumption of dishes taken away from an Asian restaurant revealed significant amounts of cereulide, reaching up to 13,200 ng/g of food. The occurrence of cereulide in rice dishes collected from various restaurants was therefore evaluated using the liquid chromatography coupled with tandem mass spectrometry method, which allows for the direct quantification of the toxin in food. The cereulide prevalence was found to be 7.4% when samples were analyzed at the day of sampling, but reached 12.9% when exposed to temperature abuse conditions (25°C). The cereulide concentrations observed in cooked rice dishes were low (approximately 4 ng/g of food). However, since little is known yet about the potential chronic toxicity of cereulide, one needs to be very careful and vigilant.

  1. Finite-difference time-domain analysis of a complete transverse electromagnetic cell loaded with liquid biological media in culture dishes.

    Science.gov (United States)

    Popović, M; Hagness, S C; Taflove, A

    1998-08-01

    Transverse electromagnetic (TEM) cells can be used for exposing biological culture specimens to electromagnetic fields and observing possible anomalous effects. The uniformity of field exposure is critical to quantifying the biological response versus the electromagnetic dose. Standing waves and other electromagnetic field nonuniformities can cause nonuniform exposure. This paper reports the results of high-resolution three-dimensional finite-difference time-domain (FDTD) simulations of a complete TEM cell designed for operation at 837 MHz. Several different cases were studied in which the number of culture dishes, the depth of the culture liquid, and the orientation of the culture dishes were varied. Further, the effect of the culture-dish glass bottom thickness and the meniscus of the liquid medium were examined. The FDTD results show that there is a significant nonuniform field and specific absorption rate (SAR) distribution within the culture medium for each case examined. Hence, biological dose-response experiments using the TEM cells should account for the possibility of strong localized SAR peaking in the culture media to provide useful data in setting exposure standards for wireless communications.

  2. Waste Electrical and Electronic Equipment

    DEFF Research Database (Denmark)

    Bigum, Marianne Kristine Kjærgaard; Christensen, Thomas Højlund

    2011-01-01

    Waste electrical and electronic equipment (WEEE) is one of the fastest growing special waste types with an estimated growth of 3–5% per year (Cui and Forssberg, 2003). WEEE is a very heterogeneous waste type that contains many compounds that are considered to be harmful to both humans and the env......Waste electrical and electronic equipment (WEEE) is one of the fastest growing special waste types with an estimated growth of 3–5% per year (Cui and Forssberg, 2003). WEEE is a very heterogeneous waste type that contains many compounds that are considered to be harmful to both humans...

  3. Mechanical (turbines and auxiliary equipment)

    CERN Document Server

    Sherry, A; Cruddace, AE

    2013-01-01

    Modern Power Station Practice, Volume 3: Mechanical (Turbines and Auxiliary Equipment) focuses on the development of turbines and auxiliary equipment used in power stations in Great Britain. Topics covered include thermodynamics and steam turbine theory; turbine auxiliary systems such as lubrication systems, feed water heating systems, and the condenser and cooling water plants. Miscellaneous station services, and pipework in power plants are also described. This book is comprised of five chapters and begins with an overview of thermodynamics and steam turbine theory, paying particular attenti

  4. Waste Electrical and Electronic Equipment

    DEFF Research Database (Denmark)

    Bigum, Marianne Kristine Kjærgaard; Christensen, Thomas Højlund

    2011-01-01

    Waste electrical and electronic equipment (WEEE) is one of the fastest growing special waste types with an estimated growth of 3–5% per year (Cui and Forssberg, 2003). WEEE is a very heterogeneous waste type that contains many compounds that are considered to be harmful to both humans and the env......Waste electrical and electronic equipment (WEEE) is one of the fastest growing special waste types with an estimated growth of 3–5% per year (Cui and Forssberg, 2003). WEEE is a very heterogeneous waste type that contains many compounds that are considered to be harmful to both humans...

  5. Several Detailed Problems in the Translation of Chinese Dishes-from the Fashionable Chinese Dishes in the American Operas%中国菜肴翻译的几个细节性问题--从美剧中走俏的中国菜肴谈起

    Institute of Scientific and Technical Information of China (English)

    李华芳

    2015-01-01

    美国影视剧中经常出现中国菜肴,这些中国菜肴的译名对于对我们解决中国菜肴翻译的细节性问题具有重要意义。本文对美国电视剧《生活大爆炸》的一个点餐片段中提及的中餐英译名进行了分析,对菜名汉译过程中的几个重要的细节问题进行了探讨。%The Chinese dishes always appear in American TV series and their translation have important significance on solving detailed problems in the translation of Chinese dishes for us.This paper analyzes the English translation of popular Chinese di-shes mentioned in an episode of the TV series the Big Bang Theory,exploring some detailed problems in the Chinese translation of dishes.

  6. Mechanical Impedance Control in the Human Arm While Manually Transporting an Open-Top Fluid Filled Dish

    Directory of Open Access Journals (Sweden)

    Navit Roth

    2011-01-01

    Full Text Available The present study deals with stabilizing aspects of a hand-held dish filled with liquid while walking steadily. This is an attempt to decipher the neuro-muscular strategies employed and the mechanical responses of the arm during certain tasks of manual materials handling. The experimental configuration included a cup and the test-subject’s hand as an ‘end-effector’ of a serial three-link system representing the upper limb. These links are connected together by the wrist, elbow and shoulder joints. The tested subjects walked at constant speed on a treadmill while aiming to minimize liquid spillage from the cup. The motion of the limb and shoulder girdle served as inputs to a model to reveal the impedance adjustments during the simultaneous control of grasping and walking under ordinary conditions, and when one of the joints is affected. A regressive function used to express stiffness, included first-order dependence on angle and on angular velocity. The function used for damping included first-order dependence on angular velocity. Redundancies in the numerical solution were eliminated using multicollinearity diagnostic algorithms. The results revealed that the wrist joint was found to have constant stiffness and damping and no regulation of these coefficients was necessary during gait. Both in the elbow and shoulder joints stiffness included a constant coefficient as well as an angular velocity-dependent coefficient. Although all tested subjects demonstrated ability to prevent spillage of liquid, there was a considerable variability among the results obtained, indicating that the compensatory mechanisms employed by each subject to regulate the mechanical impedance were subjective. These results can help in the optimization of manual materials handeling tasks in industrial settings as well as future design of prosthetic arms, robotic appliances and man machine interfacing devices.

  7. Level II scour analysis for Bridge 16 (BURKTH00070016) on Town Highway 7, crossing Dish Mill Brook, Burke, Vermont

    Science.gov (United States)

    Burns, Ronda L.; Severance, Tim

    1997-01-01

    This report provides the results of a detailed Level II analysis of scour potential at structure BURKTH00070016 on Town Highway 7 crossing Dish Mill Brook, Burke, Vermont (figures 1–8). A Level II study is a basic engineering analysis of the site, including a quantitative analysis of stream stability and scour (U.S. Department of Transportation, 1993). Results of a Level I scour investigation also are included in Appendix E of this report. A Level I investigation provides a qualitative geomorphic characterization of the study site. Information on the bridge, gleaned from Vermont Agency of Transportation (VTAOT) files, was compiled prior to conducting Level I and Level II analyses and is found in Appendix D. The site is in the White Mountain section of the New England physiographic province in northeastern Vermont. The 6.0-mi2 drainage area is in a predominantly rural and forested basin. In the vicinity of the study site, the surface cover is forest except on the left bank upstream which is brushland. In the study area, Dish Mill Brook has an incised, sinuous channel with a slope of approximately 0.04 ft/ft, an average channel top width of 40 ft and an average bank height of 6 ft. The channel bed material ranges from sand to boulder with a median grain size (D50) of 94.1 mm (0.309 ft). The geomorphic assessment at the time of the Level I and Level II site visit on August 7, 1995, indicated that the reach was stable. The Town Highway 7 crossing of Dish Mill Brook is a 28-ft-long, two-lane bridge consisting of one 24-foot steel-beam span (Vermont Agency of Transportation, written communication, March 24, 1995). The opening length of the structure parallel to the bridge face is 24.8 ft. The bridge is supported by vertical, concrete abutments with wingwalls. The channel is skewed approximately 35 degrees to the opening while the computed opening-skew-to-roadway is 35 degrees. A scour hole 1.0 ft deeper than the mean thalweg depth was observed along the left and right

  8. Strategy Guideline. HVAC Equipment Sizing

    Energy Technology Data Exchange (ETDEWEB)

    Burdick, Arlan [IBACOS, Inc., Pittsburgh, PA (United States)

    2012-02-01

    This guide describes the equipment selection of a split system air conditioner and furnace for an example house in Chicago, IL as well as a heat pump system for an example house in Orlando, FL. The required heating and cooling load information for the two example houses was developed in the Department of Energy Building America Strategy Guideline: Accurate Heating and Cooling Load Calculations.

  9. Lifting operations and lifting equipment

    NARCIS (Netherlands)

    Douwes, M.

    2013-01-01

    Lifting operations are inherent to many occupations in the construction industry. They can be performed manually or using lifting equipment. Both manual lifting and mechanical lifting operations can put construction workers at great risk of injury or health symptoms causing sick leave or disability.

  10. The NOD3 software package: A graphical user interface-supported reduction package for single-dish radio continuum and polarisation observations

    Science.gov (United States)

    Müller, Peter; Krause, Marita; Beck, Rainer; Schmidt, Philip

    2017-10-01

    Context. The venerable NOD2 data reduction software package for single-dish radio continuum observations, which was developed for use at the 100-m Effelsberg radio telescope, has been successfully applied over many decades. Modern computing facilities, however, call for a new design. Aims: We aim to develop an interactive software tool with a graphical user interface for the reduction of single-dish radio continuum maps. We make a special effort to reduce the distortions along the scanning direction (scanning effects) by combining maps scanned in orthogonal directions or dual- or multiple-horn observations that need to be processed in a restoration procedure. The package should also process polarisation data and offer the possibility to include special tasks written by the individual user. Methods: Based on the ideas of the NOD2 package we developed NOD3, which includes all necessary tasks from the raw maps to the final maps in total intensity and linear polarisation. Furthermore, plot routines and several methods for map analysis are available. The NOD3 package is written in Python, which allows the extension of the package via additional tasks. The required data format for the input maps is FITS. Results: The NOD3 package is a sophisticated tool to process and analyse maps from single-dish observations that are affected by scanning effects from clouds, receiver instabilities, or radio-frequency interference. The "basket-weaving" tool combines orthogonally scanned maps into a final map that is almost free of scanning effects. The new restoration tool for dual-beam observations reduces the noise by a factor of about two compared to the NOD2 version. Combining single-dish with interferometer data in the map plane ensures the full recovery of the total flux density. Conclusions: This software package is available under the open source license GPL for free use at other single-dish radio telescopes of the astronomical community. The NOD3 package is designed to be

  11. 21 CFR 58.61 - Equipment design.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Equipment design. 58.61 Section 58.61 Food and... PRACTICE FOR NONCLINICAL LABORATORY STUDIES Equipment § 58.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall...

  12. 40 CFR 792.61 - Equipment design.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 31 2010-07-01 2010-07-01 true Equipment design. 792.61 Section 792.61...) GOOD LABORATORY PRACTICE STANDARDS Equipment § 792.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall...

  13. Energy-related laboratory equipment (ERLE) guidelines

    Energy Technology Data Exchange (ETDEWEB)

    1995-01-01

    This document describes the Used Energy-Related Laboratory Equipment grants, and eligibility and procedures for participation. The document contains tables identifying typical equipment that may be requested, where to review ERLE equipment lists, and where to mail applications, a description of the eligible equipment grants access data system, and a copy of the ERLE grant application and instructions for its completion and submission.

  14. 21 CFR 606.60 - Equipment.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Equipment. 606.60 Section 606.60 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS CURRENT GOOD MANUFACTURING PRACTICE FOR BLOOD AND BLOOD COMPONENTS Equipment § 606.60 Equipment. (a) Equipment used in the collection, processing,...

  15. 7 CFR 58.626 - Packaging equipment.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Packaging equipment. 58.626 Section 58.626 Agriculture....626 Packaging equipment. Packaging equipment designed to mechanically fill and close single service... Standards for Equipment for Packaging Frozen Desserts and Cottage Cheese. Quality Specifications for...

  16. 14 CFR 27.1415 - Ditching equipment.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Ditching equipment. 27.1415 Section 27.1415... STANDARDS: NORMAL CATEGORY ROTORCRAFT Equipment Safety Equipment § 27.1415 Ditching equipment. (a) Emergency... accommodate one life preserver for each occupant for which certification for ditching is requested. (c)...

  17. 14 CFR 29.1415 - Ditching equipment.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Ditching equipment. 29.1415 Section 29.1415 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Equipment Safety Equipment § 29.1415 Ditching equipment....

  18. 46 CFR 197.460 - Diving equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Diving equipment. 197.460 Section 197.460 Shipping COAST... GENERAL PROVISIONS Commercial Diving Operations Periodic Tests and Inspections of Diving Equipment § 197.460 Diving equipment. The diving supervisor shall insure that the diving equipment designated for...

  19. 40 CFR 160.61 - Equipment design.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Equipment design. 160.61 Section 160... LABORATORY PRACTICE STANDARDS Equipment § 160.61 Equipment design. Equipment used in the generation... appropriate design and adequate capacity to function according to the protocol and shall be suitably located...

  20. Solar Power Satellites

    CERN Document Server

    Flournoy, Don M

    2012-01-01

    Communication satellites are a $144 billion industry. Is there any space-based industry that could possibly beat that market? 'Solar Power Satellites' shows why and how the space satellite industry will soon begin expanding its market from relaying signals to Earth to generating energy in space and delivering it to the ground as electricity. In all industrialized nations, energy demand is growing exponentially. In the developing world, the need for energy is as basic as food and water. The Sun's energy is available everywhere, and it is non-polluting. As business plans demonstrate its technical feasibility, commercial potential, and environmental acceptability, every country on Earth will look to space for the power it needs.

  1. Geostationary satellites collocation

    CERN Document Server

    Li, Hengnian

    2014-01-01

    Geostationary Satellites Collocation aims to find solutions for deploying a safe and reliable collocation control. Focusing on the orbital perturbation analysis, the mathematical foundations for orbit and control of the geostationary satellite are summarized. The mathematical and physical principle of orbital maneuver and collocation strategies for multi geostationary satellites sharing with the same dead band is also stressed. Moreover, the book presents some applications using the above algorithms and mathematical models to help readers master the corrective method for planning station keeping maneuvers. Engineers and scientists in the fields of aerospace technology and space science can benefit from this book. Hengnian Li is the Deputy Director of State Key Laboratory of Astronautic Dynamics, China.

  2. AVS on satellite

    Science.gov (United States)

    Zhao, Haiwu; Wang, Guozhong; Hou, Gang

    2005-07-01

    AVS is a new digital audio-video coding standard established by China. AVS will be used in digital TV broadcasting and next general optical disk. AVS adopted many digital audio-video coding techniques developed by Chinese company and universities in recent years, it has very low complexity compared to H.264, and AVS will charge very low royalty fee through one-step license including all AVS tools. So AVS is a good and competitive candidate for Chinese DTV and next generation optical disk. In addition, Chinese government has published a plan for satellite TV signal directly to home(DTH) and a telecommunication satellite named as SINO 2 will be launched in 2006. AVS will be also one of the best hopeful candidates of audio-video coding standard on satellite signal transmission.

  3. Laser experiments in light cloudiness with the geostationary satellite ARTEMIS

    Science.gov (United States)

    Kuzkov, V.; Kuzkov, S.; Sodnik, Z.

    2016-08-01

    The geostationary satellite ARTEMIS was launched in July 2001. The satellite is equipped with a laser communication terminal, which was used for the world's first inter-satellite laser communication link between ARTEMIS and the low earth orbit satellite SPOT-4. Ground-to-space laser communication experiments were also conducted under various atmospheric conditions involving ESA's optical ground station. With a rapidly increasing volume of information transferred by geostationary satellites, there is a rising demand for high-speed data links between ground stations and satellites. For ground-to-space laser communications there are a number of important design parameters that need to be addressed, among them, the influence of atmospheric turbulence in different atmospheric conditions and link geometries. The Main Astronomical Observatory of NAS of Ukraine developed a precise computer tracking system for its 0.7 m AZT-2 telescope and a compact laser communication package LACES (Laser Atmosphere and Communication experiments with Satellites) for laser communication experiments with geostationary satellites. The specially developed software allows computerized tracking of the satellites using their orbital data. A number of laser experiments between MAO and ARTEMIS were conducted in partial cloudiness with some amount of laser light observed through clouds. Such conditions caused high break-up (splitting) of images from the laser beacon of ARTEMIS. One possible explanation is Raman scattering of photons on molecules of a water vapor in the atmosphere. Raman scattering causes a shift in a wavelength of the photons.In addition, a different value for the refraction index appears in the direction of the meridian for the wavelength-shifted photons. This is similar to the anomalous atmospheric refraction that appears at low angular altitudes above the horizon. We have also estimated the atmospheric attenuation and the influence of atmospheric turbulence on observed results

  4. GPS satellite surveying

    CERN Document Server

    Leick, Alfred; Tatarnikov, Dmitry

    2015-01-01

    THE MOST COMPREHENSIVE, UP-TO-DATE GUIDE ON GPS TECHNOLOGY FOR SURVEYING Three previous editions have established GPS Satellite Surveying as the definitive industry reference. Now fully updated and expanded to reflect the newest developments in the field, this Fourth Edition features cutting-edge information on GNSS antennas, precise point positioning, real-time relative positioning, lattice reduction, and much more. Expert authors examine additional tools and applications, offering complete coverage of geodetic surveying using satellite technologies. The past decade has seen a major evolut

  5. Declassified intelligence satellite photographs

    Science.gov (United States)

    ,

    1998-01-01

    Recently declassified photographs from spy satellites are an important addition to the record of the Earth?s land surface held by the U.S. Geological Survey (USGS). More than 800,000 high-resolution photos taken between 1959 through 1972 were made available by Executive Order of the President. The collection is held at the USGS EROS Data Center, near Sioux Falls, S. Dak., and are offered for public sale. For some purposes in earth science studies, these photos extend the record of changes in the land surface another decade back in time from the advent of the Landsat earth-observing satellite program.

  6. Oceanography from satellites

    Science.gov (United States)

    Wilson, W. S.

    1981-01-01

    It is pointed out that oceanographers have benefited from the space program mainly through the increased efficiency it has brought to ship operations. For example, the Transit navigation system has enabled oceanographers to compile detailed maps of sea-floor properties and to more accurately locate moored subsurface instrumentation. General descriptions are given of instruments used in satellite observations (altimeter, color scanner, infrared radiometer, microwave radiometer, scatterometer, synthetic aperture radar). It is pointed out that because of the large volume of data that satellite instruments generate, the development of algorithms for converting the data into a form expressed in geophysical units has become especially important.

  7. Satellite oceanography - The instruments

    Science.gov (United States)

    Stewart, R. H.

    1981-01-01

    It is pointed out that no instrument is sensitive to only one oceanographic variable; rather, each responds to a combination of atmospheric and oceanic phenomena. This complicates data interpretation and usually requires that a number of observations, each sensitive to somewhat different phenomena, be combined to provide unambiguous information. The distinction between active and passive instruments is described. A block diagram illustrating the steps necessary to convert data from satellite instruments into oceanographic information is included, as is a diagram illustrating the operation of a radio-frequency radiometer. Attention is also given to the satellites that carry the various oceanographic instruments.

  8. GPS User Equipment Performance Evaluation.

    Science.gov (United States)

    1979-11-01

    simulation of range dynamics of the satellite/user paths. The JGA provides four CW signals aid a I’N modulated RF signal so as to simulate up to 5 jummers...VN e (PN) 4 VE e (PE) ViH e (PCT) VN e (PE) - VE e (PN) e (VAT)= VN e (VN) 4 VE e (VE) VH e (VCT)= V e (V) - VE e (VN) V H For the true North (TN

  9. Integrated Satellite-HAP Systems

    DEFF Research Database (Denmark)

    Cianca, Ernestina; De Sanctis, Mauro; De Luise, Aldo

    2005-01-01

    for an efficient hybrid terrestrial-satellite communication system. Two integrated HAP-satellite scenarios are presented, in which the HAP is used to overcome some of the shortcomings of satellite- based communications. Moreover, it is shown that the integration of HAPs with satellite systems can be used......Thus far, high-altitude platform (HAP)-based systems have been mainly conceived as an alternative to satellites for complementing the terrestrial network. This article aims to show that HAP should no longer be seen as a competitor technology by investors of satellites, but as a key element...

  10. Satellite orbit determination and gravity field recovery from satellite-to-satellite tracking

    Science.gov (United States)

    Wakker, K. F.; Ambrosius, B. A. C.; Leenman, H.

    1989-07-01

    Studies on satellite-to-satellite tracking (SST) with POPSAT (a geodetic satellite concept) and a ERS-class (Earth observation) satellite, a Satellite-to-Satellite Tracking (SST) gravity mission, and precise gravity field determination methods and mission requirements are reported. The first two studies primarily address the application of SST between the high altitude POPSAT and an ERS-class or GRM (Geopotential Research Mission) satellite to the orbit determination of the latter two satellites. Activities focussed on the determination of the tracking coverage of the lower altitude satellite by ground based tracking systems and by POPSAT, orbit determination error analysis and the determination of the surface forces acting on GRM. The third study surveys principles of SST, uncertainties of existing drag models, effects of direct luni-solar attraction and tides on orbit and the gravity gradient observable. Detailed ARISTOTELES (which replaced POPSAT) orbit determination error analyses were performed for various ground based tracking networks.

  11. Man-made Satellites

    Institute of Scientific and Technical Information of China (English)

    郝昌明

    2005-01-01

    If you watch the sky about an hour after the sun goes down, you may see some “moving stars”. But they're not real stars. They're manmade satellites (卫星). And the biggest of all is the International Space Station (ISS国际空间站).

  12. Observations of artificial satellites

    Directory of Open Access Journals (Sweden)

    A. MAMMANO

    1964-06-01

    Full Text Available The following publication gives the results of photographic
    observations of artificial satellites made at Asiago during the second
    and third year of this programme. The fixed camera technique and that
    with moving film (the latter still in its experimental stage have been used.

  13. Perception via satellite

    Science.gov (United States)

    Robinove, Charles J.

    1970-01-01

    The earth resources observation satellite (EROS) program in the Department of the Interior is intended to gather and use data from satellites and aircraft on natural and man-made features of the earth's surface. Earth resources technology satellite will provide the EROS program with data for use in dealing with natural resource problems and understanding the interaction between man and the environment. Applications will include studies of tectonic features, hydrologic problems, location of fish schools, determination of the conditions of range land, mapping land use for urban planning, studies of erosion and change along coastlines and major streams, and inventories of land use and land forms. In addition, the ERTS data may be used for detecting forest and crop diseases and inventorying crops. The ERTS satellite will be in a polar, sun-synchronous orbit so that each point on the earth's surface will be sensed every 17 to 20 days, at the same time of day. Multispectral photography is being investigated for its usefulness in hydrology. Side-looking airborne radar has not yet been widely used in hydrologic studies, although it is an excellent tool for all-weather, day or night, coverage of large areas. Other techniques being investigated include passive microwave radiometry, ultraviolet and visible stimulated luminescence, and absorption spectroscopy.

  14. Satellite Photometric Error Determination

    Science.gov (United States)

    2015-10-18

    of nearly specular reflections from most solar panels. Our primary purpose in presenting these two plots is to demonstrate the usefulness of...than a transformation for stars because the spectral energy distribution of satellites can change with phase angle and is subject to specular

  15. Creating Better Satellite Conferences.

    Science.gov (United States)

    Horner, Tommy

    1998-01-01

    Presents four ways to improve broadcasts of company satellite conferences, including creative site selection (using facilities at educational institutions rather than hotel rooms); creative programming (using graphics and other interruptions to break up lectures or speeches); creative crew selection; and creative downlink site activities (to…

  16. OMV With Satellite

    Science.gov (United States)

    1986-01-01

    This 1986 artist's concept shows the Orbital Maneuvering Vehicle (OMV) towing a satellite. As envisioned by Marshall Space Flight Center plarners, the OMV would be a remotely-controlled free-flying space tug which would place, rendezvous, dock, and retrieve orbital payloads.

  17. Advances in satellite oceanography

    Science.gov (United States)

    Brown, O. B.; Cheney, R. E.

    1983-01-01

    Technical advances and recent applications of active and passive satellite remote sensing techniques to the study of oceanic processes are summarized. The general themes include infrared and visible radiometry, active and passive microwave sensors, and buoy location systems. The surface parameters of sea surface temperature, windstream, sea state, altimetry, color, and ice are treated as applicable under each of the general methods.

  18. Cibola flight experiment satellite

    Science.gov (United States)

    Davies, P.; Liddle, Doug; Paffett, John; Sweeting, Martin; Curiel, A.; Sun, Wei; Eves, Stuart

    2004-11-01

    In order to achieve an "economy of scale" with respect to payload capacity the major trend in telecommunications satellites is for larger and larger platforms. With these large platforms the level of integration between platform and payload is increasing leading to longer delivery schedules. The typical lifecycle for procurement of these large telecommunications satellites is now 3-6 years depending on the level of non-recurring engineering needed. Surrey Satellite Technology Ltd (SSTL) has designed a low-cost platform aimed at telecommunications and navigation applications. SSTL's Geostationary Minisatellite Platform (GMP) is a new entrant addressing the lower end of the market with payloads up to 250kg requiring less than 1.5 kW power. The British National Space Centre through the MOSAIC Small Satellite Initiative supported the development of GMP. The main design goals for GMP are low-cost for the complete mission including launch and operations and a platform allowing flexible payload accommodation. GMP is specifically designed to allow rapid development and deployment with schedules typically between 1 and 2 years from contract signature to flight readiness. GMP achieves these aims by a modular design where the level of integration between the platform and payload is low. The modular design decomposes the satellite into three major components - the propulsion bay, the avionics bay and the payload module. Both the propulsion and avionics bays are reusable, largely unchanged, and independent of the payload configuration. Such a design means that SSTL or a 3rd party manufacturer can manufacture the payload in parallel to the platform with integration taking place quite late in the schedule. In July 2003 SSTL signed a contract for ESA's first Galileo navigation satellite known as GSTBV2/A. The satellite is based on GMP and ESA plan to launch it into a MEO orbit late in 2005. The second flight of GMP is likely to be in 2006 carrying a geostationary payload

  19. Communication Systems through Artificial Earth Satellites (Selected Pages)

    Science.gov (United States)

    1987-02-05

    POX Fs (8.2.11) is 0(F) dF If on input of weighing circuit fluctuation noise with uniform spectrum acts, spectral power density in numerator and...Possibly also realization MV with asynchronous operation of terrestrial stations, that we will designate through MVA . In the case MVA each terrestrial...according to the frequcrncy. With MVA through receiving-transmitting equipment of satellite into some tiMe intervals simultaneous possible passage of signals

  20. Defense Meteorological Satellite Program (DMSP)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Defense Meteorological Satellite Program (DMSP) satellites collect visible and infrared cloud imagery as well as monitoring the atmospheric, oceanographic,...

  1. Used energy-related laboratory equipment grant program for institutions of higher learning. Eligible equipment catalog

    Energy Technology Data Exchange (ETDEWEB)

    1994-07-01

    This is a listing of energy related equipment available through the Energy-Related Laboratory Equipment Grant Program which grants used equipment to institutions of higher education for energy-related research. Information included is an overview of the program, how to apply for a grant of equipment, eligibility requirements, types of equipment available, and the costs for the institution.

  2. Waterway Equipment - Boat, Barge, Motor

    Science.gov (United States)

    2012-09-25

    and service systems; deck and special machinery; and hoisting gear and equipment are operated and monitored throughout the entire test period...loaded statically to 200 percent of the ramp design hoist condition. This load is held for a minimum of three minutes. 4.6.6.2 Data Required...the contents fall short of filling a container. Wake The body of water that tends to follow a ship. It is set in motion by the friction with the

  3. Profitability Versus Construction Equipment Maintenance

    Science.gov (United States)

    2010-05-01

    E7(/(3+21(180%(5 ,QFOXGHDUHDFRGH XX-05-2010 Master’s Thesis DEC 2009 - MAY 2010 Profitability Versus Construction Equipment Maintenance...optimization of a perceived profit . This project recommends a decision support model that can be used by private and public entities alike to determine the...best fir acquisition method between rent-lease-buy and guidance for profitability optimization. Methods of life cycle cost estimating and decision

  4. [Equipment and technology in robotics].

    Science.gov (United States)

    Murphy, Declan; Challacombe, Ben; Nedas, Tim; Elhage, Oussama; Althoefer, Kaspar; Seneviratne, Lakmal; Dasgupta, Prokar

    2007-05-01

    We review the evolution and current status of robotic equipment and technology in urology. We also describe future developments in the key areas of virtual reality simulation, mechatronics and nanorobotics. The history of robotic technology is reviewed and put into the context of current systems. Experts in the associated fields of nanorobotics, mechatronics and virtual reality simulation simulation review the important future developments in these areas.

  5. Strategy Guideline: HVAC Equipment Sizing

    Energy Technology Data Exchange (ETDEWEB)

    Burdick, A.

    2012-02-01

    The heating, ventilation, and air conditioning (HVAC) system is arguably the most complex system installed in a house and is a substantial component of the total house energy use. A right-sized HVAC system will provide the desired occupant comfort and will run efficiently. This Strategy Guideline discusses the information needed to initially select the equipment for a properly designed HVAC system. Right-sizing of an HVAC system involves the selection of equipment and the design of the air distribution system to meet the accurate predicted heating and cooling loads of the house. Right-sizing the HVAC system begins with an accurate understanding of the heating and cooling loads on a space; however, a full HVAC design involves more than just the load estimate calculation - the load calculation is the first step of the iterative HVAC design procedure. This guide describes the equipment selection of a split system air conditioner and furnace for an example house in Chicago, IL as well as a heat pump system for an example house in Orlando, Florida. The required heating and cooling load information for the two example houses was developed in the Department of Energy Building America Strategy Guideline: Accurate Heating and Cooling Load Calculations.

  6. CERN computing equipment for Senegal

    CERN Multimedia

    Anaïs Schaeffer

    2014-01-01

    On 26 May, CERN once again had the honour of donating computing equipment to a foreign institute.   This time, around 100 servers and five network hubs were sent to Senegal, making it the seventh country, after Morocco, Ghana, Bulgaria, Serbia, Egypt and the Philippines, to receive a donation of computing equipment from the Organization. The official ceremony was held at CERN on 26 May in the presence of the Director-General, Rolf Heuer, and Senegal's ambassador to Geneva, Fodé Seck, who both expressed their enthusiasm for the project. The equipment is intended for Cheikh Anta Diop University (UCAD) in Dakar and will be of particular use to students attending the African School of Fundamental Physics and its Applications (ASP 2014) taking place from 3 to 23 August, for which CERN is a partner. The ASP allows a large number of African students to hone their skills in high-energy physics and to forge professional links with fellow physicists in Africa and Europe. ...

  7. Data center equipment location and monitoring system

    DEFF Research Database (Denmark)

    2011-01-01

    , and runs a software application program that communicates with the equipment rack controllers. The software application program of the central control computer stores IDs of the equipment rack controllers and each of its connected electronic ID tags in a database.; The software application program......A data center equipment location system includes both hardware and software to provide for location, monitoring, security and identification of servers and other equipment in equipment racks. The system provides a wired alternative to the wireless RFID tag system by using electronic ID tags...... connected to each piece of equipment, each electronic ID tag connected directly by wires to a equipment rack controller on the equipment rack. The equipment rack controllers then link over a local area network to a central control computer. The central control computer provides an operator interface...

  8. DFH Satellite Co.,Ltd.

    Institute of Scientific and Technical Information of China (English)

    SunQing

    2004-01-01

    DFH Satellite Co.,Ltd. is a hi-tech enterprise founded and sponsored by China Aerospace Science and Technology Corporation(CASC) and one of CASC subsidiaries,China Academy of Space Technology (CAST). The company is mainly engaged in the research and development of small satellites and micro-satellites, Osystem designs and product development for satellite application projects as well as the international exchanges and cooperation.

  9. Emerging markets for satellite data communications in the public service

    Science.gov (United States)

    Potter, J. G.

    1978-01-01

    The paper discusses some of the current and potential markets for satellite data communications as projected by the Public Service Satellite Consortium (PSSC). Organizations in the public service sector are divided into three categories, depending on their expected benefits and organizational changes due to increased satellite telecommunications use: A - modest institutional adjustments are necessary and significant productivity gains are likely; B - institutional requirements picture is promising, but more information is needed to assess benefits and risk; and C - major institutional adjustments are needed, risks are high but possible benefits are high. These criteria are applied to the U.S. health care system, continuing education, equipment maintenance, libraries, environmental monitoring, and other potential markets. The potential revenues are seen to be significant, but what is needed is a cooperative effort by common carriers and major public service institutions to aggregate the market.

  10. Mobile satellite service for Canada

    Science.gov (United States)

    Sward, David

    1988-05-01

    The Mobile Satellite (MSAT) system and a special program designed to provide interim mobile satellite services (IMSS) during the construction phase of MSAT are described. A mobile satellite system is a key element in extending voice and and data telecommunications to all Canadians.

  11. Lithium-ion Battery Charge Methodologies Observed with Portable Electronic Equipment

    Science.gov (United States)

    Jeevarajan, Judith

    2009-01-01

    Commercial lithium-ion batteries in portable electronic equipment has been used by NASA for space applications since 1999. First battery that was certified for flight and flown for Shuttle use was the Canon BP 927 (2.7 Ah) battery pack. Since then, numerous portable equipment with li-ion batteries have been certified and flown and remain on-orbit for crew usage. Laptops (two generations with third one being worked on now) Camcorder Camera PDA 2 versions (second one being li-ion polymer cells) Satellite Phone Due to expense and time, certified batteries are used with different equipment with the help of adapters or by working with the manufacturer of the equipment to build the appropriate battery compartment and connector. Certified and dedicated chargers are available on Shuttle and on the ISS for safe charging.

  12. JCE Online: Equipment Buyers Guide

    Science.gov (United States)

    Holmes, Jon L.

    1999-01-01

    The Equipment Buyers Guide was edited by Jo Rita Jordan. The new Equipment Buyers Guide, bound into the back of this issue, is also a new resource of JCE Internet. This resource provides an online source for the information contained in the printed guide. Placing this information online allows us to regularly update it and to provide live links to the suppliers' WWW sites. The organization of the online version parallels that of the print version. There is an alphabetical list of suppliers and a categorical listing. Links to these lists are provided on every page in the left-hand navigation bar. To quickly find information about a particular supplier, you click Supplier List, click the letter that begins the supplier's name, and scroll through the list to find the supplier. To find which suppliers provide a particular type of instrument or equipment, use the Categories link; click the category of the equipment you are looking for and then click the link to a supplier. You will then be taken to an alphabetical supplier listing page where you can scroll until you find the particular supplier of the item for which you are looking. Once you have found a supplier, the online Equipment Buyers Guide gives you the traditional contact information. But in addition, you also get one-click access to the WWW sites of the suppliers that have them. Depending on the site, you should be able to find information about the items that you seek and may even be able to order the items online! We think that you will find the online version of the Equipment Buyers Guide useful. To make it more useful, please send your suggestions, any errors or omissions you find, and any additional categories to the editor at jjordan@world.std.com The online Equipment Buyers Guide can be found at JCE Online at http://JChemEd.chem.wisc.edu/JCEWWW/Resources/EBG/ JCE Online in '99 JCE Online is your online source of "all things JCE". In order to provide you with an even more useful online resource, JCE

  13. Satellite Aerodynamics and Density Determination from Satellite Dynamic Response

    Science.gov (United States)

    Karr, G. R.

    1972-01-01

    The aerodynamic drag and lift properties of a satellite are first expressed as a function of two parameters associated with gas-surface interaction at the satellite surface. The dynamic response of the satellite as it passes through the atmosphere is then expressed as a function of the two gas-surface interaction parameters, the atmospheric density, the satellite velocity, and the satellite orientation to the high speed flow. By proper correlation of the observed dynamic response with the changing angle of attack of the satellite, it is found that the two unknown gas-surface interaction parameters can be determined. Once the gas-surface interaction parameters are known, the aerodynamic properties of the satellite at all angles of attack are also determined.

  14. Sodium content and energy of 47 commercial dishes in four restaurants in Beijing%北京市四家餐馆47种菜肴中钠及能量含量的评估

    Institute of Scientific and Technical Information of China (English)

    李晓琴; 王竹; 门建华; 向雪松; 王国栋; 杨月欣

    2013-01-01

    目的 评估北京市4家中餐馆菜肴的钠及能量含量水平.方法 2011年6-8月,采用方便抽样的方法,在北京市选择4家中型中餐馆,选取消费者食用次数≥6次且有2家以上餐馆提供的菜肴,共47道,其中凉菜9道、烹制菜肴38道.每道菜抽取1整份成品菜肴,分析测定其能量和钠含量,计算钠密度.结果 用中位数表示,凉菜、烹制菜肴的钠含量分别为580、522 mg/100 g(Z=0.83,P>0.05)或1427、2301 mg/份(Z=2.03,P<0.05);钠密度分别为1902、670 mg/1000 kJ(Z=2.81,P <0.01);能量分别为514、717kJ/100g(Z=2.15,P<0.05)或11 13、3492 kJ/份(Z =4.03,P<0.05);在调查的47道菜肴中,46.8%(22/47)的菜肴每份的钠含量超过了居民每日钠参考摄入量(2200 mg).结论 北京市中型中餐馆常见菜肴钠含量可能较高,凉菜虽然能量相对较低,但钠密度较高,其对就餐者钠摄入量的贡献不容忽视.%Objective To evaluate the sodium content and energy of commercial dishes in 4 Chinese restaurants in Beijing.Methods From June to August of 2011,4 medium-sized restaurants were selected by convenience sampling method.Overall,47 commercial dishes (including 9 cold dishes and 38 cooked dishes) consumed at least 6 times by consumers and provided by at least 2 restaurants were selected.One complete serving was selected for each dish to investigate its energy and sodium content,and calculate its sodium density.Results The median value of sodium content in cold dishes and cooked dishes were 580,522 mg/100 g(Z =0.83,P >0.05) or 1427,2301 mg/serving(Z =2.03,P <0.05) ; the median sodium density for cold and cooked dishes were 1902 and 670 mg/1000 kJ (Z =2.81,P < 0.01) ; the median value of energy in cold dishes and cooked dishes were 514,717 kJ/100 g(Z =2.15,P < 0.05) or 1113,3492 kJ/serving (Z =4.03,P < 0.05).Of the 47 dishes,46.8% (22/47) exceeded the daily recommendation of sodium content for Chinese residents(2200 mg).Conclusion The

  15. 碟式斯特林太阳自动跟踪控制系统设计%Design of Dish Stirling Solar Automatic Tracking Control System

    Institute of Scientific and Technical Information of China (English)

    范伟成; 宗情; 彭小方; 梁伟青

    2012-01-01

    针对碟式斯特林太阳能热发电中的太阳跟踪问题,提出了基于GPS的开环程序粗跟踪和四象限硅光电池跟踪校准的闭环跟踪解决方法。以ATmega128单片机为主控制器,根据GPS模块和反馈装置获得的信息,控制碟转向机构的水平、俯仰两个方向运动,实现对太阳位置的跟踪,形成了一个精度高、受环境影响较小的闭环控制系统,能够保证碟式聚光器的光斑始终落在斯特林发动机的接收器上。%Aiming at the solar tracking problem in Dish Stirling solar thermal power generation, this paper puts forward an open-loop program rough tracking based on GPS and four-quadrant silicon photocell close-loop tracking. Taking ATmega128 as main controller, a close-loop control system with high precision and less environmental impacts is formed. The system controls the movements o~ the dish steering machanism in horizontal direction and pitch attitude according to the information from GPS module and feedback instruments, and realizes sun position tracking. It can ensure the spot of the dish fall on the receiver of the Stirling engine all the time.

  16. The effects of packaging method (vacuum pouch vs. plastic tray) on spoilage in a cook-chill pork-based dish kept under refrigeration.

    Science.gov (United States)

    Díaz, Pedro; Garrido, María Dolores; Bañón, Sancho

    2010-03-01

    The effects of two packaging methods on the spoilage of a cook-chill pork-based dish kept under refrigeration were studied. Raw pork cuts and pre-cooked tomato sauce were packed under vacuum "sous vide" in polyamide-polypropylene pouches (SV) or into translucent polypropylene trays under modified atmosphere (80% N(2)+20% CO(2)) and sealed with a top film (PT). Samples were cooked inside the pack at an oven temperature/time of 70 degrees C/7h, chilled at 3 degrees C and stored at 2 degrees C for up to 90days. Microbial (psychrotrophs, lactic-acid bacteria, Enterobacteriaceae, moulds and yeasts), physical-chemical (pH, water activity and total acidity) and sensory (colour, odour, flavour, texture and acceptance) parameters were determined. Heat penetration was faster in SV (2 degrees C/min) than in PT (1 degrees C/min) (core temperature). Both packaging methods were equally effective in protecting against microbial spoilage for 90 day at 2 degrees C. Minor counts were only detected for lactic-acid bacteria and anaerobic psychrotrophs in SV. No Enterobacteriaceae growth was found. Slight differences between SV and PT in pH and total acidity were observed. SV and PT had similar effects on the sensory preservation of the dishes. A gradual loss of acceptance of the cooked pork and tomato sauce was observed. Rancid flavour in PT and warmed-over-flavour in SV were noted in the final stages of storage. According to acceptance scores, the shelf-life of both SV and PT was 56 days at 2 degrees C. Both packaging methods can be used to manufacture sous vide meat-based dishes subsequently stored under refrigeration for catering use. Copyright 2009 Elsevier Ltd. All rights reserved.

  17. Thematic mapping from satellite imagery

    CERN Document Server

    Denègre, J

    2013-01-01

    Thematic Mapping from Satellite Imagery: A Guidebook discusses methods in producing maps using satellite images. The book is comprised of five chapters; each chapter covers one stage of the process. Chapter 1 tackles the satellite remote sensing imaging and its cartographic significance. Chapter 2 discusses the production processes for extracting information from satellite data. The next chapter covers the methods for combining satellite-derived information with that obtained from conventional sources. Chapter 4 deals with design and semiology for cartographic representation, and Chapter 5 pre

  18. Cooperative and cognitive satellite systems

    CERN Document Server

    Chatzinotas, Symeon; De Gaudenzi, Riccardo

    2015-01-01

    Cooperative and Cognitive Satellite Systems provides a solid overview of the current research in the field of cooperative and cognitive satellite systems, helping users understand how to incorporate state-of-the-art communication techniques in innovative satellite network architectures to enable the next generation of satellite systems. The book is edited and written by top researchers and practitioners in the field, providing a comprehensive explanation of current research that allows users to discover future technologies and their applications, integrate satellite and terrestrial systems

  19. Analysis and Design of a Dish/Stirling System for Solar Electric Generation with a 2.7 kW Air-Cooled Engine

    OpenAIRE

    Beltrán-Chacón R.; Velázquez-Limón N.; Sauceda-Carvajal D.

    2012-01-01

    This paper presents a mathematical modeling, simulation and design of a solar power system of a parabolic dish with an air-cooled Stirling engine of 2.7 kW. The model used for the solar concentrator, the cavity and the Stirling engine were successfully validated against experimental data. Based on a parametric study, the design of the components of the engine is carried out. The study shows that as system capacity increases, the overall efficiency is limited by the power required by the fan, ...

  20. Declassified Intelligence Satellite Photographs

    Science.gov (United States)

    ,

    2008-01-01

    Declassified photographs from U.S. intelligence satellites provide an important worldwide addition to the public record of the Earth's land surface. This imagery was released to the National Archives and Records Administration (NARA) and the U.S. Geological Survey (USGS) in accordance with Executive Order 12951 on February 23, 1995. The NARA has the original declassified film and a viewing copy. The USGS has another copy of the film to complement the Landsat archive. The declassified collection involves more than 990,000 photographs taken from 1959 through 1980 and was released on two separate occasions: February 1995 (Declass 1) and September 2002 (Declass 2). The USGS copy is maintained by the Earth Resources Observation and Science (EROS) Center, near Sioux Falls, South Dakota. Both the NARA and EROS provide public access to this unique collection that extends the record of land-surface change back another decade from the advent of the Landsat program that began satellite operations in 1972.

  1. Satellites in Canadian broadcasting

    Science.gov (United States)

    Siocos, C. A.

    The involvement of Canadian broadcasting and related enterprises in satellite telecommunications is surveyed. This includes point-to-point transmissions and direct ones to the general public. The mode of such utilizations is indicated in both these cases. For the forthcoming DBS systems the many types of service offerings and utilization concepts under discussion elasewhere are presented as well as the business prospects and regulatory climate offering them.

  2. Neptune: Minor Satellites

    Science.gov (United States)

    Murdin, P.

    2003-04-01

    All but one of Neptune's minor satellites orbit within or just outside its ringsystem; the exception is the distant object Nereid. Some of them are betterdescribed as `mid-sized' rather than `minor', but are included under thisheading as little is known of them. The inner four, with approximatediameters, are Naiad (60 km), Thalassa (80 km), Despina (150 km) and Galatea(160 km). The first three lie...

  3. Satellite Surveillance: Domestic Issues

    Science.gov (United States)

    2010-02-01

    earthquake and tsunami in the Indian Ocean and Hurricane Katrina in 2005, when the NGA provided graphics for “relief efforts that depicted the locations of...that show the damage resulting from an earthquake , fire, flood, hurricane, oil spill, or volcanic eruption.8 Bush Administration Policies...Satellite information has continued to have important civil applications in such disparate areas as the movement of glaciers in Yakutat Bay in Alaska

  4. Electrical Ground Support Equipment Fabrication, Specification for

    Science.gov (United States)

    Denson, Erik C.

    2014-01-01

    This document specifies parts, materials, and processes used in the fabrication, maintenance, repair, and procurement of electrical and electronic control and monitoring equipment associated with ground support equipment (GSE) at the Kennedy Space Center (KSC).

  5. 40 CFR 265.32 - Required equipment.

    Science.gov (United States)

    2010-07-01

    ... equipment, or automatic sprinklers, or water spray systems. ... of equipment specified below: (a) An internal communications or alarm system capable of providing... assistance from local police departments, fire departments, or State or local emergency response teams;...

  6. Modernization of Deployable Airfield Debris Removal Equipment

    Science.gov (United States)

    2017-04-01

    measurements and to calculate volumes. A market survey of available loading and sweeping equipment was conducted to populate a database of physical...1 1.2 Objective and scope...Equipment ............................................................................................................................. 4 3 Market

  7. Proceedings of FED remote maintenance equipment workshop

    Energy Technology Data Exchange (ETDEWEB)

    Sager, P.; Garin, J.; Hager, E.R.; Spampinato, P.T.; Tobias, D.; Young, N.

    1981-11-01

    A workshop was convened in two sessions in January and March 1981, on the remote maintenance equipment for the Fusion Engineering Device (FED). The objectives of the first session were to familiarize the participants with the status of the design of the FED and to develop a remote maintenance equipment list for the FED. The objective of the second session was to have the participants present design concepts for the equipment which had been identified in the first session. The equipment list was developed for general purpose and special purpose equipment. The general purpose equipment was categorized as manipulators and other, while the special purpose equipment was subdivided according to the reactor subsystem it serviced: electrical, magnetic, and nuclear. Both mobile and fixed base manipulators were identified. Handling machines were identified as the major requirement for special purpose equipment.

  8. Communications satellites - The experimental years

    Science.gov (United States)

    Edelson, B. I.

    1983-10-01

    Only eight years after the launc of Sputnik-1 by the Soviet Union, the first commercial satellite, 'Early Bird', entered service. In just twelve years commercial satellite service extended around the earth and became profitable. The reasons for the successful development of the communications satellite services in a comparatively short time are considered. These reasons are related to the presence of three ingredients, taking into account technology to create the system, communications requirements to form a market, and a management structure to implement the system. The formation of the concept of using earth orbiting satellites for telecommunications is discussed. It is pointed out that the years from 1958 to 1964 were the true 'experimental years' for satellite communications. The rapid development of technology during this crucial period is described, giving attention to passive satellites, active systems, and development satellites.

  9. Resurs-P" Satellite Hyperspectral Data: Preliminary Evaluation of Information Capacities

    Science.gov (United States)

    Zelentsov, Viacheslav; Sokolov, Boris; Grigorieva, Olga; Mochalov, Viktor; Potryasaev, Semen; Shumeiko, Viktor

    2016-08-01

    Satellite-based hyperspectral sensors provide spectroscopic information in relatively narrow contiguous spectral bands over a large area, and this property can be useful for a lot of practical tasks. "Resurs-P" hyperspectral equipment provides a new class of Earth observation data to improve Earth surface observability. The main features of this equipment are considered and the results of new hyperspectral data applications to solve problems vineyards and forest analysis and also depths measurements are given in the article.

  10. Tethered satellite design

    Science.gov (United States)

    Manarini, G.

    1986-01-01

    The capability of the satellite to perform a variety of space operations to be accomplished from the shuttle is reviewed considering use of the satellite with man-in-loop and closed loop modes and deployment (toward or away from Earth, up to 100 km), stationkeeping, retrieval and control of the satellite. Scientific payloads are to be used to perform experiments and scientific investigation for applications such as magnetometry, electrodynamics, atmospheric science, chemical release, communications, plasmaphysics, dynamic environment, and power and thrust generation. The TSS-S will be reused for at least 3 missions after reconfiguration and refurbishment by changing the peculiar mission items such as thermal control, fixed boom for experiments, aerodynamic tail for yaw attitude control, external skin, experiments, and any other feature. The TSS-S is to be composed of three modules in order to allow independent integration of a single module and to facilitate the refurbishment and reconfiguration between flights. The three modules are service, auxiliary propulsion, and payload modules.

  11. Heart Monitoring By Satellite

    Science.gov (United States)

    1978-01-01

    The ambulance antenna shown is a specially designed system that allows satellite-relayed two-way communications between a moving emergency vehicle and a hospital emergency room. It is a key component of a demonstration program aimed at showing how emergency medical service can be provided to people in remote rural areas. Satellite communication permits immediate, hospital- guided treatment of heart attacks or other emergencies by ambulance personnel, saving vital time when the scene of the emergency is remote from the hospital. If widely adopted, the system could save tens of thousands of lives annually in the U.S. alone, medical experts say. The problem in conventional communication with rural areas is the fact that radio signals travel in line of sight. They may be blocked by tall buildings, hills and mountains, or even by the curvature of the Earth, so signal range is sharply limited. Microwave relay towers could solve the problem, but a complete network of repeater towers would be extremely expensive. The satellite provides an obstruction-free relay station in space.

  12. Tactical Satellite 3

    Science.gov (United States)

    Davis, T. M.; Straight, S. D.; Lockwook, R. B.

    2008-08-01

    Tactical Satellite 3 is an Air Force Research Laboratory Science and Technology (S&T) initiative that explores the capability and technological maturity of small, low-cost satellites. It features a low cost "plug and play" modular bus and low cost militarily significant payloads - a Raytheon developed Hyperspectral imager and secondary payload data exfiltration provided by the Office of Naval Research. In addition to providing for ongoing innovation and demonstration in this important technology area, these S&T efforts also help mitigate technology risk and establish a potential concept of operations for future acquisitions. The key objectives are rapid launch and on-orbit checkout, theater commanding, and near-real time theater data integration. It will also feature a rapid development of the space vehicle and integrated payload and spacecraft bus by using components and processes developed by the satellite modular bus initiative. Planned for a late summer 2008 launch, the TacSat-3 spacecraft will collect and process images and then downlink processed data using a Common Data Link. An in-theater tactical ground station will have the capability to uplink tasking to spacecraft and will receive full data image. An international program, the United Kingdom Defence Science and Technology Laboratory (DSTL) and Australian Defence Science and Technology Organisation (DSTO) plan to participate in TacSat-3 experiments.

  13. A satellite anemometer

    Science.gov (United States)

    Hanson, W. B.; Heelis, R. A.

    1995-01-01

    This report describes the design, development, and testing of components of a satellite anemometer, an instrument for measuring neutral winds in the upper atmosphere from a satellite platform. The device, which uses four nearly identical pressure sensors, measures the angle of arrival of the bulk neutral flow in the satellite frame of reference. It could also be used in a feedback loop to control spacecraft attitude with respect to the ram velocity direction. We have now developed miniaturized ionization pressure gauges that will work well from the slip flow region near 115 km up to the base of the exosphere, which covers the entire altitude range currently being considered for Tether. Laboratory tests have demonstrated a very linear response to changes in ram angle out to +/- 20 deg. (transverse wind component of 2.7 km s(exp -1)) from the ram, and a monotonic response to out beyond 45 deg. Pitch (vertical wind) and yaw (horizontal wind) can be sampled simultaneously and meaningfully up to 10 Hz. Angular sensitivity of 30 arc seconds (approximately 1 ms(exp -1) is readily attainable, but absolute accuracy for winds will be approximately 1 deg (130 m/s) unless independent attitude knowledge is available. The critical elements of the design have all been tested in the laboratory.

  14. Binary Satellite Galaxies

    CERN Document Server

    Evslin, Jarah

    2013-01-01

    Suggestions have appeared in the literature that the following five pairs of Milky Way and Andromeda satellite galaxies are gravitationally bound: Draco and Ursa Minor, Leo IV and V, Andromeda I and III, NGC 147 and 185, and the Magellanic clouds. Under the assumption that a given pair is gravitationally bound, the Virial theorem provides an estimate of its total mass and so its instantaneous tidal radius. For all of these pairs except for the Magellanic clouds the resulting total mass is 2 to 4 orders of magnitude higher than that within the half light radius. Furthermore in the case of each pair except for Leo IV and Leo V, the estimated tidal radius is inferior to the separation between the two satellites. Therefore all or almost all of these systems are not gravitationally bound. We note several possible explanations for the proximities and similar radial velocities of the satellites in each pair, for example they may have condensed from the same infalling structure or they may be bound by a nongravitatio...

  15. Testing a satellite automatic nutation control system. [on synchronous meteorological satellite

    Science.gov (United States)

    Hrasiar, J. A.

    1974-01-01

    Testing of a particular nutation control system for the synchronous meteorological satellite (SMS) is described. The test method and principles are applicable to nutation angle control for other satellites with similar requirements. During its ascent to synchronous orbit, a spacecraft like the SMS spins about its minimum-moment-of-inertia axis. An uncontrolled spacecraft in this state is unstable because torques due to fuel motion increase the nutation angle. However, the SMS is equipped with an automatic nutation control (ANC) system which will keep the nutation angle close to zero. Because correct operation of this system is critical to mission success, it was tested on an air-bearing table. The ANC system was mounted on the three-axis air-bearing table which was scaled to the SMS and equipped with appropriate sensors and thrusters. The table was spun up in an altitude chamber and nutation induced so that table motion simulated spacecraft motion. The ANC system was used to reduce the nutation angle. This dynamic test of the ANC system met all its objectives and provided confidence that the ANC system will control the SMS nutation angle.

  16. Fitness Equipment Brings Business Opportunities

    Institute of Scientific and Technical Information of China (English)

    Lin Feng

    2011-01-01

    @@ Nowadays, as you walk in the domestic cities, color-ful and dynamic signs of gyms will always come into your view.And when you walk into the gym, you must first be greet-ed by rows of neatly stacked tread-mills.People running on the tread-mill, regardless of age, regardless of gender, can control their running speed all by themselves, with sports games playing in the monitor in the front of the equipment, and ears full of beautiful music from their iPods.

  17. First Magdas Equipment In Ecuador

    CERN Document Server

    López, Ericson; Vicente, Klever; Yumoto, K; Vasquez, N; Matsushita, H; Shishime, A; Vásconez, C

    2013-01-01

    The Magnetic Data Acquisition System (MAGDAS) was installed in the protected Jerusalem Park in Malchingui-Ecuador in October of 2012, under the joint collaboration between Kyushu University of Japan and the Quito Astronomical Observatory of the National Polytechnic School of Ecuador. In this paper, we describe the installation process and present the preliminary data obtained with the MAGDAS equipment. The behavior of the four components, D, H, Z and F allow us to see the importance of having the Ecuador station where the magnetic field has not been systematically measured before, in valuable contribution to study of the equatorial atmosphere.

  18. 46 CFR 154.1430 - Equipment locker.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Equipment locker. 154.1430 Section 154.1430 Shipping... Equipment § 154.1430 Equipment locker. One of each item of equipment under §§ 154.1400 and 154.1420 must be stowed in a marked locker: (a) On the open deck in or adjacent to the cargo area; or (b) In...

  19. APPLICATION OF VISION METROLOGY TO IN-ORBIT MEASUREMENT OF LARGE REFLECTOR ONBOARD COMMUNICATION SATELLITE FOR NEXT GENERATION MOBILE SATELLITE COMMUNICATION

    Directory of Open Access Journals (Sweden)

    M. Akioka

    2016-06-01

    Full Text Available Satellite for next generation mobile satellite communication service with small personal terminal requires onboard antenna with very large aperture reflector larger than twenty meters diameter because small personal terminal with lower power consumption in ground base requires the large onboard reflector with high antenna gain. But, large deployable antenna will deform in orbit because the antenna is not a solid dish but the flexible structure with fine cable and mesh supported by truss. Deformation of reflector shape deteriorate the antenna performance and quality and stability of communication service. However, in case of digital beam forming antenna with phased array can modify the antenna beam performance due to adjustment of excitation amplitude and excitation phase. If we can measure the reflector shape precisely in orbit, beam pattern and antenna performance can be compensated with the updated excitation amplitude and excitation phase parameters optimized for the reflector shape measured every moment. Softbank Corporation and National Institute of Information and Communications Technology has started the project "R&D on dynamic beam control technique for next generation mobile communication satellite" as a contracted research project sponsored by Ministry of Internal Affairs and Communication of Japan. In this topic, one of the problem in vision metrology application is a strong constraints on geometry for camera arrangement on satellite bus with very limited space. On satellite in orbit, we cannot take many images from many different directions as ordinary vision metrology measurement and the available area for camera positioning is quite limited. Feasibility of vision metrology application and general methodology to apply to future mobile satellite communication satellite is to be found. Our approach is as follows: 1 Development of prototyping simulator to evaluate the expected precision for network design in zero order and first order

  20. Application of Vision Metrology to In-Orbit Measurement of Large Reflector Onboard Communication Satellite for Next Generation Mobile Satellite Communication

    Science.gov (United States)

    Akioka, M.; Orikasa, T.; Satoh, M.; Miura, A.; Tsuji, H.; Toyoshima, M.; Fujino, Y.

    2016-06-01

    Satellite for next generation mobile satellite communication service with small personal terminal requires onboard antenna with very large aperture reflector larger than twenty meters diameter because small personal terminal with lower power consumption in ground base requires the large onboard reflector with high antenna gain. But, large deployable antenna will deform in orbit because the antenna is not a solid dish but the flexible structure with fine cable and mesh supported by truss. Deformation of reflector shape deteriorate the antenna performance and quality and stability of communication service. However, in case of digital beam forming antenna with phased array can modify the antenna beam performance due to adjustment of excitation amplitude and excitation phase. If we can measure the reflector shape precisely in orbit, beam pattern and antenna performance can be compensated with the updated excitation amplitude and excitation phase parameters optimized for the reflector shape measured every moment. Softbank Corporation and National Institute of Information and Communications Technology has started the project "R&D on dynamic beam control technique for next generation mobile communication satellite" as a contracted research project sponsored by Ministry of Internal Affairs and Communication of Japan. In this topic, one of the problem in vision metrology application is a strong constraints on geometry for camera arrangement on satellite bus with very limited space. On satellite in orbit, we cannot take many images from many different directions as ordinary vision metrology measurement and the available area for camera positioning is quite limited. Feasibility of vision metrology application and general methodology to apply to future mobile satellite communication satellite is to be found. Our approach is as follows: 1) Development of prototyping simulator to evaluate the expected precision for network design in zero order and first order 2) Trial

  1. Data Center Equipment Location and Monitoring System

    DEFF Research Database (Denmark)

    2013-01-01

    Abstract: Data center equipment location systems include hardware and software to provide information on the location, monitoring, and security of servers and other equipment in equipment racks. The systems provide a wired alternative to the wireless RFID tag system by using electronic ID tags...

  2. 46 CFR 154.1005 - Equipment approval.

    Science.gov (United States)

    2010-10-01

    ... carried. (b) Each submerged cargo pump motor installation must be specially approved by the Commandant (CG... FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Electrical § 154.1005 Equipment approval. (a) Electrical equipment that is required to be intrinsically safe...

  3. 46 CFR 28.880 - Hydraulic equipment.

    Science.gov (United States)

    2010-10-01

    ... hydraulic equipment and the adjacent work area. Protection shall be afforded to the operator of hydraulic... 46 Shipping 1 2010-10-01 2010-10-01 false Hydraulic equipment. 28.880 Section 28.880 Shipping... INDUSTRY VESSELS Aleutian Trade Act Vessels § 28.880 Hydraulic equipment. (a) Each hydraulic system must...

  4. Recent R&D in Drilling Equipment

    Institute of Scientific and Technical Information of China (English)

    Sun Zuchen; Huang Zhiqian

    1997-01-01

    @@ Situation for Drilling Equipment Technical performance of drilling equipment and perfection of supporting systems hold the key to drilling safety, technical procedure development and drilling cost. In the end of the 1980s, the stituation for drilling equipment was not optimistic in China because of poor technical performance, low-level supporting system and scarcity of electric-driven rigs.

  5. New Trends in School Science Equipment.

    Science.gov (United States)

    Lowe, Norman K., Ed.

    This four-part volume examines trends, problems, and issues related to school science equipment. Part 1 focuses on laboratory work and practical activities in science and technology education, considering equipment and curriculum development, equipment development related to curricula in Brazil, uses of local resources for practical work,…

  6. 46 CFR 28.405 - Hydraulic equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Hydraulic equipment. 28.405 Section 28.405 Shipping... Operate With More Than 16 Individuals on Board § 28.405 Hydraulic equipment. (a) Each hydraulic system... than four times the system maximum operating pressure. (c) Each hydraulic system must be equipped...

  7. Used equipment-standard contract elements

    Institute of Scientific and Technical Information of China (English)

    Gary F. Alexander

    2004-01-01

    @@ One thing that both the purchase of new and used equipment has in common is the need for a comprehensive purchase agreement. The big difference is that while repetitive purchases of new equipment often only require the modification of one or more sections of a contract, every used equipment transaction and contract is normally different.

  8. Load Bearing Equipment for Bone and Muscle

    Science.gov (United States)

    Shackelford, Linda; Griffith, Bryan

    2015-01-01

    Resistance exercise on ISS has proven effective in maintaining bone mineral density and muscle mass. Exploration missions require exercise with similar high loads using equipment with less mass and volume and greater safety and reliability than resistance exercise equipment used on ISS (iRED, ARED, FWED). Load Bearing Equipment (LBE) uses each exercising person to create and control the load to the partner.

  9. Data Center Equipment Location and Monitoring System

    DEFF Research Database (Denmark)

    2013-01-01

    Abstract: Data center equipment location systems include hardware and software to provide information on the location, monitoring, and security of servers and other equipment in equipment racks. The systems provide a wired alternative to the wireless RFID tag system by using electronic ID tags...

  10. 14 CFR 23.1415 - Ditching equipment.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Ditching equipment. 23.1415 Section 23.1415 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS... Ditching equipment. (a) Emergency flotation and signaling equipment required by any operating rule in...

  11. 46 CFR 121.210 - Heating equipment.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Heating equipment. 121.210 Section 121.210 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... SYSTEMS AND EQUIPMENT Cooking and Heating § 121.210 Heating equipment. (a) Each heater must be...

  12. 30 CFR 77.1914 - Electrical equipment.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Electrical equipment. 77.1914 Section 77.1914... Shaft Sinking § 77.1914 Electrical equipment. (a) Electric equipment employed below the collar of a.... (b) The insulation of all electric conductors employed below the collar of any slope or shaft...

  13. 38 CFR 21.216 - Special equipment.

    Science.gov (United States)

    2010-07-01

    ... which the veteran needs special equipment and is eligible for such equipment under other VA programs... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Special equipment. 21.216...) VOCATIONAL REHABILITATION AND EDUCATION Vocational Rehabilitation and Employment Under 38 U.S.C. Chapter...

  14. Proposal for the donation of LEP equipment

    CERN Document Server

    2000-01-01

    CERN has announced that LEP equipment will become available for donations to educational and scientific research institutes, to museums and public bodies in Member States and non-member States. A number of requests for a limited amount of equipment have been received. CERN has no further use for this equipment. The Finance Committee is invited to approve these donations.

  15. Material Handling Equipment Evaluation for Crater Repair

    Science.gov (United States)

    2016-11-01

    material handling equipment with a reduced logistical footprint for use by crater repair teams in airfield damage repair (ADR) scenarios. A market ...compared to currently utilized material handling equipment. This report presents the results of the market survey and equipment evaluations. Results...1 1.2 Objective and scope

  16. 29 CFR 1926.952 - Mechanical equipment.

    Science.gov (United States)

    2010-07-01

    ... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Power Transmission and Distribution § 1926.952 Mechanical equipment. (a) General. (1) Visual inspections shall be made of the equipment to determine that it... 29 Labor 8 2010-07-01 2010-07-01 false Mechanical equipment. 1926.952 Section 1926.952...

  17. Carbon Absorber Retrofit Equipment (CARE)

    Energy Technology Data Exchange (ETDEWEB)

    Klein, Eric [Neumann Systems Group, Incorporated, Colorado Springs, CO (United States)

    2015-12-23

    During Project DE-FE0007528, CARE (Carbon Absorber Retrofit Equipment), Neumann Systems Group (NSG) designed, installed and tested a 0.5MW NeuStream® carbon dioxide (CO2) capture system using the patented NeuStream® absorber equipment and concentrated (6 molal) piperazine (PZ) as the solvent at Colorado Springs Utilities’ (CSU’s) Martin Drake pulverized coal (PC) power plant. The 36 month project included design, build and test phases. The 0.5MW NeuStream® CO2 capture system was successfully tested on flue gas from both coal and natural gas combustion sources and was shown to meet project objectives. Ninety percent CO2 removal was achieved with greater than 95% CO2product purity. The absorbers tested support a 90% reduction in absorber volume compared to packed towers and with an absorber parasitic power of less than 1% when configured for operation with a 550MW coal plant. The preliminary techno-economic analysis (TEA) performed by the Energy and Environmental Research Center (EERC) predicted an over-the-fence cost of $25.73/tonne of CO2 captured from a sub-critical PC plant.

  18. Liquid-Liquid Extraction Equipment

    Energy Technology Data Exchange (ETDEWEB)

    Jack D. Law; Terry A. Todd

    2008-12-01

    Solvent extraction processing has demonstrated the ability to achieve high decontamination factors for uranium and plutonium while operating at high throughputs. Historical application of solvent extraction contacting equipment implies that for the HA cycle (primary separation of uranium and plutonium from fission products) the equipment of choice is pulse columns. This is likely due to relatively short residence times (as compared to mixer-settlers) and the ability of the columns to tolerate solids in the feed. Savannah River successfully operated the F-Canyon with centrifugal contactors in the HA cycle (which have shorter residence times than columns). All three contactors have been successfully deployed in uranium and plutonium purification cycles. Over the past 20 years, there has been significant development of centrifugal contactor designs and they have become very common for research and development applications. New reprocessing plants are being planned in Russia and China and the United States has done preliminary design studies on future reprocessing plants. The choice of contactors for all of these facilities is yet to be determined.

  19. ISIS Electronics Flying on Korean LEO Satellites

    Science.gov (United States)

    Remy, S.; Mosset, E.; Park, Sungwoo

    2014-08-01

    Saft (Defense & Space, France), ASP (Advanced Space Power, Germany) and KARI (Korean Aerospace Research Institute, South Korea) developed an autonomous battery management system to carry out cell packages balancing, by-pass system activation and cell package discharge after failure detection. This high reliability electronics called ISIS (Intelligent Surveillance Integrated System) has been designed, tested and qualified in the frame of the Kompsat-3, Kompsat-5 and Kompsat-3A large LEO Korean KARI Satellites. Kompsat-3 and 3A (4.8 kWh battery) and Kompsat-5 (5.2 kWh battery equipped with a demanding imaging radar system) are powered during daily sun eclipses with respectively one 4P12S or 4P13S VES100 li-ion batteries managed by ISIS system.

  20. Satellite augmentation of cellular type mobile radio telephone systems

    Science.gov (United States)

    Anderson, Roy E.

    NASA's ATS-6 satellite relayed voice bandwidth communications between five trucks and the trucking company dispatchers as the trucks traveled throughout the north-eastern quarter of the contiguous United States. The experiment, conducted over a seven month period, demonstrated that propagation characteristics are much different for the satellite-mobile links than for terrestrial-mobile links. A properly designed satellite system can provide high quality, reliable voice and data communications except where the vehicle-satellite path is shadowed by a structure or terrain feature. Mobile equipment in the experiment was adapted from commercial mobile radios. The vehicle antennas were 75 cm tall, 2 cm diam. Another experiment proved the feasibility of vehicle position surveillance using active two-way tone-code ranging through ATS-6 to provide one line of position and passive one-way ranging by measuring the time-of-arrival of a signal from an independent satellite. A position fix was printed out at an earth station 1 sec after it sent the interrogation signal to the distant vehicle, a towboat on the Mississippi River. The line of position from ATS-6 was accurate to 0.1 nautical mile using a voice bandwidth ranging signal. The line of position from the NOAA GOES satellite was accurate to 2 miles, using 100 Hz signal bandwidth. If the signal from the independent satellite had the same bandwidth and signal-to-noise ratio as ATS-6, the fixes would have been accurate to about 0.1 nautical mile. A concept study concluded that satellites might be a cost effective augmentation of terrestrial cellular type mobile radio telephone systems. The satellites would serve thinly populated areas where terrestrial systems are not cost effective. In the United States, the satellites would serve about 90% of the land area where 20% of the population resides. A multibeam satellite with many channels in each beam would be compatible with the urban terrestrial systems and together they would

  1. Differentiation of mouse iPS cells into ameloblast-like cells in cultures using medium conditioned by epithelial cell rests of Malassez and gelatin-coated dishes.

    Science.gov (United States)

    Yoshida, Koki; Sato, Jun; Takai, Rie; Uehara, Osamu; Kurashige, Yoshihito; Nishimura, Michiko; Chiba, Itsuo; Saitoh, Masato; Abiko, Yoshihiro

    2015-09-01

    Induced pluripotent stem (iPS) cells are generated from adult cells and are potentially of great value in regenerative medicine. Recently, it was shown that iPS cells can differentiate into ameloblast-like cells in cultures using feeder cells. In the present study, we sought to induce differentiation of ameloblast-like cells from iPS cells under feeder-free conditions using medium conditioned by cultured epithelial cell rests of Malassez (ERM) cells and gelatin-coated dishes. Two culture conditions were compared: co-cultures of iPS cells and ERM cells; and, culture of iPS cells in ERM cell-conditioned medium. Differentiation of ameloblast-like cells in the cultures was assessed using real-time RT-PCR assays of expression of the marker genes keratin 14, amelogenin, and ameloblastin and by immunocytochemical staining for amelogenin. We found greater evidence of ameloblast-like cell differentiation in the cultures using the conditioned medium. In the latter, the level of amelogenin expression increased daily and was significantly higher than controls on the 7th, 10th, and 14th days. Expression of ameloblastin also increased daily and was significantly higher than controls on the 14th day. The present study demonstrates that mouse iPS cells can be induced to differentiate into ameloblast-like cells in feeder-free cell cultures using ERM cell-conditioned medium and gelatin-coated dishes.

  2. Enumeration of salmonellae in table eggs, pasteurized egg products, and egg-containing dishes by using quantitative real-time PCR.

    Science.gov (United States)

    Jakociune, Dziuginta; Pasquali, Frédérique; da Silva, Cristiana Soares; Löfström, Charlotta; Hoorfar, Jeffrey; Klein, Günter; Manfreda, Gerardo; Olsen, John Elmerdahl

    2014-03-01

    Salmonellae are a major cause of food-borne outbreaks in Europe, with eggs and egg products being identified as major sources. Due to the low levels of salmonellae in eggs and egg products, direct quantification is difficult. In the present study, enrichment quantitative real-time PCR (qPCR) was employed for enumeration of salmonellae in different matrices: table eggs, pasteurized egg products, and egg-containing dishes. Salmonella enterica serovar Enteritidis and S. enterica serovar Tennessee were used to artificially contaminate these matrices. The results showed a linear regression between the numbers of salmonellae and the quantification cycle (Cq) values for all matrices used, with the exception of pasteurized egg white. Standard curves were constructed by using both stationary-phase cells and heat-stressed cells, with similar results. Finally, this method was used to evaluate the fate of salmonellae in two egg-containing dishes, long egg and tiramisu, at abused refrigeration temperatures, and results indicated the growth of bacteria over a 1-week period. In conclusion, enrichment qPCR was shown to be reliable for enumeration of salmonellae in different egg products.

  3. A detailed radiation heat transfer study of a dish-Stirling receiver: The impact of cavity wall radiation properties and cavity shapes

    Science.gov (United States)

    Garrido, Jorge; Wang, Wujun; Nilsson, Martin; Laumert, Björn

    2016-05-01

    A detailed 3-D radiation analysis of a dish-Stirling cavity receiver is carried out to estimate the cavity steady-state temperatures in order to assess the receiver integrity, lifetime and efficiency performance. For this purpose, a parabolic dish was modeled with 5.2 m focal length, 8.85 m aperture diameter and 2 mrad surface error. Three generic cavity shapes (cylindrical, diamond-shaped and reverse-conical) with three different emissivities (0.2, 0.4 and 0.7) are studied. Worst-case scenario heat generations (total absorbed radiation), maximum steady-state temperatures and energy balances of the cavities are calculated to evaluate the receiver performance. The results show that reverse-conical cavities can significantly reduce cavity wall peak temperatures (by 40-120 K), improve the temperature evenness and decrease the radiation losses by 4-5%. Regarding radiation properties, low reflectivities present lower steady-state temperatures even for low/moderate direct solar fluxes. Due to the lower temperatures, lower total thermal losses are also expected.

  4. Satellite broadcasting experiments and in-orbit performance of BSE

    Science.gov (United States)

    Shimoseko, S.; Yamamoto, M.; Kajikawa, M.; Arai, K.

    1981-09-01

    The Japanese medium-scale Broadcasting Satellite for Experimental Purposes (BSE) was launched in April 1978 and placed in a geostationary orbit at 110 deg E longitude. Two transmitters with bandwidths of 50 MHz and 80 MHz were mounted on the BSE transponder to conduct experiments on various television signals; no significant variation in transmission characteristics was observed during the two-year period. Rain attenuation characteristics in the 12 GHz band were studied and a value of 6.6 dB was registered in Owase, one of the most rainy areas in Japan. The strength of the rain scatter wave of the BSE uplink signal was measured to investigate the characteristics between broadcasting satellite uplink and a terrestrial link in the 14 GHz band. Uplink power control, important for the efficient operation of satellite communications systems, was shown to compensate the variations in receiving power due to fluctuations in the beam pointing of the satellite antenna. Routine operations were performed to check the three-axis attitude control, stationkeeping, housekeeping, and the bus equipment. The electrical power, secondary propulsion, thermal control, and communication subsystems were also evaluated. The first operations 1 broadcasting satellite is scheduled to be launched early in 1984.

  5. An Earth Orbiting Satellite Service and Repair Facility

    Science.gov (United States)

    Berndt, Andrew; Cardoza, Mike; Chen, John; Daley, Gunter; Frizzell, Andy; Linton, Richard; Rast, Wayne

    1989-01-01

    A conceptual design was produced for the Geosynchronous Satellite Servicing Platform (GSSP), an orbital facility capable of repairing and servicing satellites in geosynchronous orbit. The GSSP is a man-tended platform, which consists of a habitation module, operations module, service bay and truss assembly. This design review includes an analysis of life support systems, thermal and power requirements, robotic and automated systems, control methods and navigation, and communications systems. The GSSP will utilize existing technology available at the time of construction, focusing mainly on modifying and integrating existing systems. The entire facility, along with two satellite retrieval vehicles (SRV), will be placed in geosynchronous orbit by the Advanced Launch System. The SRV will be used to ferry satellites to and from the GSSP. Technicians will be transferred from Earth to the GSSP and back in an Apollo-derived Crew Transfer Capsule (CTC). These missions will use advanced telerobotic equipment to inspect and service satellites. Four of these missions are tentatively scheduled per year. At this rate, the GSSP will service over 650 satelites during the projected 25 year lifespan.

  6. Geomagnetic disturbances imprints in ground and satellite altitude observatories

    Science.gov (United States)

    Yahiat, Yasmina; Lamara, Souad; Zaourar, Naima; Hamoudi, Mohamed

    2016-04-01

    The temporal evolution of the geomagnetic field and its variations have been repeatedly studied from both ground observatories and near-earth orbiting platforms. With the advent of the space ageand the launches of geomagnetic low altitude orbits satellites, a global coverage has been achieved. Since Magsat mission, more satellites were put into orbit and some of them are still collecting data enhancing the spatial and temporal descriptions of the field. Our study uses new data gathered by the latest SWARM satellite mission launched on November, 22nd 2013. It consists of a constellation of three identical satellites carrying on board high resolution and accuracy scientific equipment. Data from this constellation will allow better understanding the multiscale behavior of the geomagnetic field. Our goal is to analyze and interpret the geomagnetic data collected by this Swarm mission, for a given period and try to separate the external disturbances from internal contributions. We consider in the study the variation of the horizontal component H, for different virtual geomagnetic observatories at the satellite altitude. The analysis of data by Swarm orbital segments shows clearly the external disturbances of the magnetic field like that occurring on 27th of August 2014. This perturbation is shown on geomagnetic indexes and is related to a coronal mass ejection (CME). These results from virtual observatories are confirmed, by the equivalent analysis using ground observatories data for the same geographic positions and same epochs. Key words: Geomagnetic field, external field, geomagnetic index, SWARM mission, virtual observatories.

  7. Satellite Upper Air Network (SUAN)

    Science.gov (United States)

    Reale, Tony L.; Thorne, Peter

    2004-10-01

    During the past 20 years of NOAA operational polar satellites, it has become evident that a growing problem concerning their utilization in Climate and also Numerical Weather Prediction (NWP) applications are the systematic errors and uncertainties inherent in the satellite measurements. Similar arguments can be made for global radiosonde observations. These uncertainties are often larger than the sensitive signals and processes, that satellite and radiosonde measurements are designed to reveal, particularly in the realm of climate. Possible strategies to quantify and compensate for these problems include the analysis of satellite overlap data and/or available collocations of satellite and ground truth (radiosonde) observations. However, overlap observations are typically not available except in extreme polar regions and current sampling strategies for compiling collocated radiosonde and satellite observations are insufficient, further compounding the inherent uncertainties in the ground-truth radiosonde data. A Satellite Upper Air Network is proposed to provide reference radiosonde launches coincident with operational polar satellite(s) overpass. The SUAN consist of 36 global radiosonde stations sub-sampled from the Global Upper Air Network (GUAN), and is designed to provide a robust, global sample of collocated radiosonde and satellite observations conducive to the monitoring and validation of satellite and radiosonde observations. The routine operation of such a network in conjunction with operational polar satellites would provide a long-term of performance for critical observations of particular importance for climate. The following report presents a candidate network of 36 upper-air sites that could comprise a SUAN. Their selection along with the mutual benefit across the satellite, radiosonde, climate, numerical weather prediction (NWP) and radiative transfer (RT) model areas are discussed.

  8. The TDCPR Management Mode of Engineering Equipment

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The Three Gorges Project is a very large project, and its structure is very complex. International advanced engineering equipment is broadly used. The state of equipment running directly influences project building qualities and limited time. According to the factual conditions of the Three Gorges Project, the characteristics of engineering equipment are analyzed. At the same time, some theories about equipment management are induced, and the TDCPR management mode of engineering equipmeat of the Three Gorges Project is put forward in order to gain the aim of managing and using equipment well and speeding up the project construction.

  9. Precise Orbit Determination of Earth's Satellites for Climate Change Investigation

    Science.gov (United States)

    Vespe, Francesco

    The tremendous improvement of the gravity field models which we are achieving with the last Earth's satellite missions like, CHAMP, GRACE and GOCE devoted to its recovery could make feasibile the use of precise orbit determination (POD) of Earth satellites as a tool for sensing global changes of some key atmosphere parameters like refractivity and extinction. Such improvements indeed, coupled with the huge number of running Earth's satellites and combinations of their orbital parameters (namely the nodes) in a gravity field free fashion (hereafter GFF) can magnify the solar radiation pressure acting on medium earth orbit satellites :GPS, Etalon and, in near real future GALILEO and its smooth modulation through the Earth's atmosphere (penumbra). We would remind that The GFF technique is able to cancel out with "n" satellite orbital parameters the first n-1 even zonal harmonics of the gravity field. Previously it was demonstrated that the signal we want to detect could in principle emerge from the noise threshold but, more refined models of the atmosphere would be needed to perform a more subtle analysis. So we will re-compute the signal features of penumbra by applying more refined atmospheric models. The analysis will be performed by including in GFF Earth's satellites equipped with DORIS systems (Jason, Spot 2-3-4-5, ENVISAT etc.) other than those ranged with SLR and GPS. The introduction of DORIS tracked satellites indeed will allow to cancel higher and higher order of even zonal harmonics and will make still more favourable the signal to noise budget. The analysis will be performed over a time span of at least few tens of years just to enhance probable climate signatures.

  10. Position surveillance using one active ranging satellite and time-of-arrival of a signal from an independent satellite

    Science.gov (United States)

    Anderson, R. E.; Frey, R. L.; Lewis, J. R.

    1980-01-01

    Position surveillance using one active ranging/communication satellite and the time-of-arrival of signals from an independent satellite was shown to be feasible and practical. A towboat on the Mississippi River was equipped with a tone-code ranging transponder and a receiver tuned to the timing signals of the GOES satellite. A similar transponder was located at the office of the towing company. Tone-code ranging interrogations were transmitted from the General Electric Earth Station Laboratory through ATS-6 to the towboat and to the ground truth transponder office. Their automatic responses included digital transmissions of time-of-arrival measurements derived from the GOES signals. The Earth Station Laboratory determined ranges from the satellites to the towboat and computed position fixes. The ATS-6 lines-of-position were more precise than 0.1 NMi, 1 sigma, and the GOES lines-of-position were more precise than 1.6 NMi, 1 sigma. High quality voice communications were accomplished with the transponders using a nondirectional antenna on the towboat. The simple and effective surveillance technique merits further evaluation using operational maritime satellites.

  11. Evolution of the NOAA National Weather Service Satellite Broadcast Network (SBN) to Europe's DVB-S satellite communications technology standard

    Science.gov (United States)

    Cragg, Phil; Brockman, William E.

    2006-08-01

    The National Oceanic and Atmospheric Administration's (NOAA) National Weather Service (NWS) uses a commercial Satellite Broadcast Network (SBN) to distribute weather data to the NWS AWIPS workstations and National Centers and to NWS Family of Service Users. Advances in science and technology from NOAA's observing systems, such as remote sensing satellites and NEXRAD radars, and advances in Numeric Weather Prediction have greatly increased the volume of data to be transmitted via the SBN. The NOAA-NWS SBN Evolution Program did a trade study resulting in the selection of Europe's DVB-S communication protocol as the basis for enabling a significant increase in the SBN capacity. The Digital Video Broadcast (DVB) group, started to develop digital TV for Europe through satellite broadcasting, has become the current standard for defining technology for satellite broadcasting of digital data for much of the world. NOAA-NWS implemented the DVB-S with inexpensive, Commercial Off The Shelf receiving equipment. The modernized NOAA-NWS SBN meets current performance goals and provides the basis for continued future expansion with no increase in current communication costs. This paper discusses aspects of the NOAA-NWS decision and the migration to the DVB-S standard for its commercial satellite broadcasts of observations and Numerical Weather Prediction data.

  12. Heat recovery equipment for engines

    Energy Technology Data Exchange (ETDEWEB)

    Segaser, C.L.

    1977-04-01

    The recovery and use of waste heat from prime movers is an important consideration for evaluating an on-site power system, since it is the basic factor that makes possible a substantial increase in fuel-use efficiency. The equipment usually employed to recover waste heat can be categorized as: (a) shell-and-tube type heat exchangers, (b) radiator-type heat exchangers, (c) exhaust gas boilers for the generation of pressurized hot water and/or steam, (d) steam separators, and (e) combined packaged units for ebulliently cooled internal combustion piston engines. The functional requirements and cost considerations involved in applying these devices for the recovery of waste heat from various types of prime-movers considered for application in the ICES Systems Engineering Program are examined.

  13. Antenna Calibration and Measurement Equipment

    Science.gov (United States)

    Rochblatt, David J.; Cortes, Manuel Vazquez

    2012-01-01

    A document describes the Antenna Calibration & Measurement Equipment (ACME) system that will provide the Deep Space Network (DSN) with instrumentation enabling a trained RF engineer at each complex to perform antenna calibration measurements and to generate antenna calibration data. This data includes continuous-scan auto-bore-based data acquisition with all-sky data gathering in support of 4th order pointing model generation requirements. Other data includes antenna subreflector focus, system noise temperature and tipping curves, antenna efficiency, reports system linearity, and instrument calibration. The ACME system design is based on the on-the-fly (OTF) mapping technique and architecture. ACME has contributed to the improved RF performance of the DSN by approximately a factor of two. It improved the pointing performances of the DSN antennas and productivity of its personnel and calibration engineers.

  14. Radio broadcasting via satellite

    Science.gov (United States)

    Helm, Neil R.; Pritchard, Wilbur L.

    1990-10-01

    Market areas offering potential for future narrowband broadcast satellites are examined, including international public diplomacy, government- and advertising-supported, and business-application usages. Technical issues such as frequency allocation, spacecraft types, transmission parameters, and radio receiver characteristics are outlined. Service and system requirements, advertising revenue, and business communications services are among the economic issues discussed. The institutional framework required to provide an operational radio broadcast service is studied, and new initiatives in direct broadcast audio radio systems, encompassing studies, tests, in-orbit demonstrations of, and proposals for national and international commercial broadcast services are considered.

  15. Understanding satellite navigation

    CERN Document Server

    Acharya, Rajat

    2014-01-01

    This book explains the basic principles of satellite navigation technology with the bare minimum of mathematics and without complex equations. It helps you to conceptualize the underlying theory from first principles, building up your knowledge gradually using practical demonstrations and worked examples. A full range of MATLAB simulations is used to visualize concepts and solve problems, allowing you to see what happens to signals and systems with different configurations. Implementation and applications are discussed, along with some special topics such as Kalman Filter and Ionosphere. W

  16. China Satellite Navigation Conference

    CERN Document Server

    Liu, Jingnan; Fan, Shiwei; Wang, Feixue

    2016-01-01

    These Proceedings present selected research papers from CSNC2016, held during 18th-20th May in Changsha, China. The theme of CSNC2016 is Smart Sensing, Smart Perception. These papers discuss the technologies and applications of the Global Navigation Satellite System (GNSS), and the latest progress made in the China BeiDou System (BDS) especially. They are divided into 12 topics to match the corresponding sessions in CSNC2016, which broadly covered key topics in GNSS. Readers can learn about the BDS and keep abreast of the latest advances in GNSS techniques and applications.

  17. China Satellite Navigation Conference

    CERN Document Server

    Liu, Jingnan; Yang, Yuanxi; Fan, Shiwei; Yu, Wenxian

    2017-01-01

    These proceedings present selected research papers from CSNC2017, held during 23th-25th May in Shanghai, China. The theme of CSNC2017 is Positioning, Connecting All. These papers discuss the technologies and applications of the Global Navigation Satellite System (GNSS), and the latest progress made in the China BeiDou System (BDS) especially. They are divided into 12 topics to match the corresponding sessions in CSNC2017, which broadly covered key topics in GNSS. Readers can learn about the BDS and keep abreast of the latest advances in GNSS techniques and applications.

  18. The Galilean Satellites

    Science.gov (United States)

    1998-01-01

    This composite includes the four largest moons of Jupiter which are known as the Galilean satellites. The Galilean satellites were first seen by the Italian astronomer Galileo Galilei in 1610. Shown from left to right in order of increasing distance from Jupiter, Io is closest, followed by Europa, Ganymede, and Callisto.The order of these satellites from the planet Jupiter helps to explain some of the visible differences among the moons. Io is subject to the strongest tidal stresses from the massive planet. These stresses generate internal heating which is released at the surface and makes Io the most volcanically active body in our solar system. Europa appears to be strongly differentiated with a rock/iron core, an ice layer at its surface, and the potential for local or global zones of water between these layers. Tectonic resurfacing brightens terrain on the less active and partially differentiated moon Ganymede. Callisto, furthest from Jupiter, appears heavily cratered at low resolutions and shows no evidence of internal activity.North is to the top of this composite picture in which these satellites have all been scaled to a common factor of 10 kilometers (6 miles) per picture element.The Solid State Imaging (CCD) system aboard NASA's Galileo spacecraft acquired the Io and Ganymede images in June 1996, the Europa images in September 1996, and the Callisto images in November 1997.Launched in October 1989, the spacecraft's mission is to conduct detailed studies of the giant planet, its largest moons and the Jovian magnetic environment. The Jet Propulsion Laboratory, Pasadena, CA, manages the mission for NASA's Office of Space Science, Washington, DC.The Jet Propulsion Laboratory, Pasadena, CA manages the Galileo mission for NASA's Office of Space Science, Washington, DC. JPL is an operating division of California Institute of Technology (Caltech).This image and other images and data received from Galileo are posted on the World Wide Web, on the Galileo mission

  19. Future communications satellite applications

    Science.gov (United States)

    Bagwell, James W.

    1992-01-01

    The point of view of the research is made through the use of viewgraphs. It is suggested that future communications satellite applications will be made through switched point to point narrowband communications. Some characteristics of which are as follows: small/low cost terminals; single hop communications; voice compatible; full mesh networking; ISDN compatible; and possible limited use of full motion video. Some target applications are as follows: voice/data networks between plants and offices in a corporation; data base networking for commercial and science users; and cellular radio internodal voice/data networking.

  20. HETE Satellite Power Subsystem

    OpenAIRE

    1993-01-01

    The HETE (High-Energy Transient Experiment) satellite a joint project between MIT's Center for Space Research and AeroAstro. is a high-energy gamma-ray burst/X-Ray/UV observatory platform. HETE will be launched into a 550 km circular orbit with an inclination of 37.7°, and has a design lifetime of 18 months. This paper presents a description of the spacecraft's power subsystem, which collects, regulates, and distributes power to the experiment payload modules and to the various spacecraft sub...