WorldWideScience

Sample records for satellite antennas phase

  1. Phased Array Transmit Antenna for a Satellite

    Science.gov (United States)

    Huggins, R. W.; Heisen, P. T.; Miller, G. E.; McMeen, D. J.; Perko, K. L.

    1999-01-01

    Active phased array antennas with electronically scanned beams offer advantages over high gain parabolic dish antennas currently used on spacecraft. Benefits include the elimination of deployable structures, no moving parts, and no torque disturbances that moving antennas impart to the spacecraft. The latter results in the conservation of spacecraft power, and the ability to take precision optical data while transmitting data. Such an antenna has been built under a contract from NASA Goddard Space Flight Center for the New Millennium Program EO- 1 satellite where it will act as the primary highspeed scientific data communication link. The antenna operates at X-band, has an integral controller and power conditioner, communicates with the spacecraft over a 1773 optical data bus, and is space qualified for low earth orbit (705 Km altitude). The nominal mission length is one year, and the operational requirement is for one 10 minute transmission a day over Spitsbergen, Norway. Details of the antenna and its performance will be described in the following paper.

  2. Optimizing Satellite Communications With Adaptive and Phased Array Antennas

    Science.gov (United States)

    Ingram, Mary Ann; Romanofsky, Robert; Lee, Richard Q.; Miranda, Felix; Popovic, Zoya; Langley, John; Barott, William C.; Ahmed, M. Usman; Mandl, Dan

    2004-01-01

    A new adaptive antenna array architecture for low-earth-orbiting satellite ground stations is being investigated. These ground stations are intended to have no moving parts and could potentially be operated in populated areas, where terrestrial interference is likely. The architecture includes multiple, moderately directive phased arrays. The phased arrays, each steered in the approximate direction of the satellite, are adaptively combined to enhance the Signal-to-Noise and Interference-Ratio (SNIR) of the desired satellite. The size of each phased array is to be traded-off with the number of phased arrays, to optimize cost, while meeting a bit-error-rate threshold. Also, two phased array architectures are being prototyped: a spacefed lens array and a reflect-array. If two co-channel satellites are in the field of view of the phased arrays, then multi-user detection techniques may enable simultaneous demodulation of the satellite signals, also known as Space Division Multiple Access (SDMA). We report on Phase I of the project, in which fixed directional elements are adaptively combined in a prototype to demodulate the S-band downlink of the EO-1 satellite, which is part of the New Millennium Program at NASA.

  3. Estimation of satellite antenna phase center offsets for Galileo

    Science.gov (United States)

    Steigenberger, P.; Fritsche, M.; Dach, R.; Schmid, R.; Montenbruck, O.; Uhlemann, M.; Prange, L.

    2016-08-01

    Satellite antenna phase center offsets for the Galileo In-Orbit Validation (IOV) and Full Operational Capability (FOC) satellites are estimated by two different analysis centers based on tracking data of a global GNSS network. The mean x- and y-offsets could be determined with a precision of a few centimeters. However, daily estimates of the x-offsets of the IOV satellites show pronounced systematic effects with a peak-to-peak amplitude of up to 70 cm that depend on the orbit model and the elevation of the Sun above the orbital plane. For the IOV y-offsets, no dependence on the orbit model exists but the scatter strongly depends on the elevation of the Sun above the orbital plane. In general, these systematic effects are significantly smaller for the FOC satellites. The z-offsets of the two analysis centers agree within the 10-15 cm level, and the time series do not show systematic effects. The application of an averaged Galileo satellite antenna model obtained from the two solutions results in a reduction of orbit day boundary discontinuities by up to one third—even if an independent software package is used.

  4. Phased Antenna Array for Global Navigation Satellite System Signals

    Science.gov (United States)

    Turbiner, Dmitry (Inventor)

    2015-01-01

    Systems and methods for phased array antennas are described. Supports for phased array antennas can be constructed by 3D printing. The array elements and combiner network can be constructed by conducting wire. Different parameters of the antenna, like the gain and directivity, can be controlled by selection of the appropriate design, and by electrical steering. Phased array antennas may be used for radio occultation measurements.

  5. Galileo satellite antenna modeling

    Science.gov (United States)

    Steigenberger, Peter; Dach, Rolf; Prange, Lars; Montenbruck, Oliver

    2015-04-01

    The space segment of the European satellite navigation system Galileo currently consists of six satellites. Four of them belong to the first generation of In-Orbit Validation (IOV) satellites whereas the other two are Full Operational Capability (FOC) satellites. High-precision geodetic applications require detailed knowledge about the actual phase center of the satellite and receiver antenna. The deviation of this actual phase center from a well-defined reference point is described by phase center offsets (PCOs) and phase center variations (PCVs). Unfortunately, no public information is available about the Galileo satellite antenna PCOs and PCVs, neither for the IOV, nor the FOC satellites. Therefore, conventional values for the IOV satellite antenna PCOs have been adopted for the Multi-GNSS experiment (MGEX) of the International GNSS Service (IGS). The effect of the PCVs is currently neglected and no PCOs for the FOC satellites are available yet. To overcome this deficiency in GNSS observation modeling, satellite antenna PCOs and PCVs are estimated for the Galileo IOV satellites based on global GNSS tracking data of the MGEX network and additional stations of the legacy IGS network. Two completely independent solutions are computed with the Bernese and Napeos software packages. The PCO and PCV values of the individual satellites are analyzed and the availability of two different solutions allows for an accuracy assessment. The FOC satellites are built by a different manufacturer and are also equipped with another type of antenna panel compared to the IOV satellites. Signal transmission of the first FOC satellite has started in December 2014 and activation of the second satellite is expected for early 2015. Based on the available observations PCO estimates and, optionally PCVs of the FOC satellites will be presented as well. Finally, the impact of the new antenna model on the precision and accuracy of the Galileo orbit determination is analyzed.

  6. Spaceborne GPS receiver antenna phase center offset and variation estimation for the Shiyan 3 satellite

    Directory of Open Access Journals (Sweden)

    Gu Defeng

    2016-10-01

    Full Text Available In determining the orbits of low Earth orbit (LEO satellites using spaceborne GPS, the errors caused by receiver antenna phase center offset (PCO and phase center variations (PCVs are gradually becoming a major limiting factor for continued improvements to accuracy. Shiyan 3, a small satellite mission for space technology experimentation and climate exploration, was developed by China and launched on November 5, 2008. The dual-frequency GPS receiver payload delivers 1 Hz data and provides the basis for precise orbit determination within the range of a few centimeters. The antenna PCO and PCV error characteristics and the principles influencing orbit determination are analyzed. The feasibility of PCO and PCV estimation and compensation in different directions is demonstrated through simulation and in-flight tests. The values of receiver antenna PCO and PCVs for Gravity Recovery and Climate Experiment (GRACE and Shiyan 3 satellites are estimated from one month of data. A large and stable antenna PCO error, reaching up to 10.34 cm in the z-direction, is found with the Shiyan 3 satellite. The PCVs on the Shiyan 3 satellite are estimated and reach up to 3.0 cm, which is slightly larger than that of GRACE satellites. Orbit validation clearly improved with independent k-band ranging (KBR and satellite laser ranging (SLR measurements. For GRACE satellites, the average root mean square (RMS of KBR residuals improved from 1.01 cm to 0.88 cm. For the Shiyan 3 satellite, the average RMS of SLR residuals improved from 4.95 cm to 4.06 cm.

  7. Spaceborne GPS receiver antenna phase center offset and variation estimation for the Shiyan 3 satellite

    Institute of Scientific and Technical Information of China (English)

    Gu Defeng; Lai Yuwang; Liu Junhong; Ju Bing; Tu Jia

    2016-01-01

    In determining the orbits of low Earth orbit (LEO) satellites using spaceborne GPS, the errors caused by receiver antenna phase center offset (PCO) and phase center variations (PCVs) are gradually becoming a major limiting factor for continued improvements to accuracy. Shiyan 3, a small satellite mission for space technology experimentation and climate exploration, was developed by China and launched on November 5, 2008. The dual-frequency GPS receiver payload delivers 1 Hz data and provides the basis for precise orbit determination within the range of a few centime-ters. The antenna PCO and PCV error characteristics and the principles influencing orbit determi-nation are analyzed. The feasibility of PCO and PCV estimation and compensation in different directions is demonstrated through simulation and in-flight tests. The values of receiver antenna PCO and PCVs for Gravity Recovery and Climate Experiment (GRACE) and Shiyan 3 satellites are estimated from one month of data. A large and stable antenna PCO error, reaching up to 10.34 cm in the z-direction, is found with the Shiyan 3 satellite. The PCVs on the Shiyan 3 satellite are estimated and reach up to 3.0 cm, which is slightly larger than that of GRACE satellites. Orbit validation clearly improved with independent k-band ranging (KBR) and satellite laser ranging (SLR) measurements. For GRACE satellites, the average root mean square (RMS) of KBR resid-uals improved from 1.01 cm to 0.88 cm. For the Shiyan 3 satellite, the average RMS of SLR resid-uals improved from 4.95 cm to 4.06 cm.

  8. Consistent Long-Time Series of GPS Satellite Antenna Phase Center Corrections

    Science.gov (United States)

    Steigenberger, P.; Schmid, R.; Rothacher, M.

    2004-12-01

    The current IGS processing strategy disregards satellite antenna phase center variations (pcvs) depending on the nadir angle and applies block-specific phase center offsets only. However, the transition from relative to absolute receiver antenna corrections presently under discussion necessitates the consideration of satellite antenna pcvs. Moreover, studies of several groups have shown that the offsets are not homogeneous within a satellite block. Manufacturer specifications seem to confirm this assumption. In order to get best possible antenna corrections, consistent ten-year time series (1994-2004) of satellite-specific pcvs and offsets were generated. This challenging effort became possible as part of the reprocessing of a global GPS network currently performed by the Technical Universities of Munich and Dresden. The data of about 160 stations since the official start of the IGS in 1994 have been reprocessed, as today's GPS time series are mostly inhomogeneous and inconsistent due to continuous improvements in the processing strategies and modeling of global GPS solutions. An analysis of the signals contained in the time series of the phase center offsets demonstrates amplitudes on the decimeter level, at least one order of magnitude worse than the desired accuracy. The periods partly arise from the GPS orbit configuration, as the orientation of the orbit planes with regard to the inertial system repeats after about 350 days due to the rotation of the ascending nodes. In addition, the rms values of the X- and Y-offsets show a high correlation with the angle between the orbit plane and the direction to the sun. The time series of the pcvs mainly point at the correlation with the global terrestrial scale. Solutions with relative and absolute phase center corrections, with block- and satellite-specific satellite antenna corrections demonstrate the effect of this parameter group on other global GPS parameters such as the terrestrial scale, station velocities, the

  9. Satellite communication antenna technology

    Science.gov (United States)

    Mittra, R. (Editor); Imbriale, W. A. (Editor); Maanders, E. J. (Editor)

    1983-01-01

    A general overview of current technology in the field of communication satellite antennas is presented. Among the topics discussed are: the design of multiple beam systems; frequency reuse; and polarization control of antenna measurements. Consideration is also given to: contour beam synthesis; dual shaped reflector synthesis; beam shaping; and offset reflector design. The applications of the above technologies to present and future generations of communications satellites is considered, with emphasis given to such systems as: the Intelsats; the Defense Satellite Communications System, (DSCS-III); Satellite Business System (SBS), and Comstar.

  10. Modeling and Simulation of Phased Array Antennas to Support Next-Generation Satellite Design

    Science.gov (United States)

    Tchorowski, Nicole; Murawski, Robert; Manning, Robert; Fuentes, Michael

    2016-01-01

    Developing enhanced simulation capabilities has become a significant priority for the Space Communications and Navigation (SCaN) project at NASA as new space communications technologies are proposed to replace aging NASA communications assets, such as the Tracking and Data Relay Satellite System (TDRSS). When developing the architecture for these new space communications assets, it is important to develop updated modeling and simulation methodologies, such that competing architectures can be weighed against one another and the optimal path forward can be determined. There have been many simulation tools developed here at NASA for the simulation of single RF link budgets, or for the modeling and simulation of an entire network of spacecraft and their supporting SCaN network elements. However, the modeling capabilities are never fully complete and as new technologies are proposed, gaps are identified. One such gap is the ability to rapidly develop high fidelity simulation models of electronically steerable phased array systems. As future relay satellite architectures are proposed that include optical communications links, electronically steerable antennas will become more desirable due to the reduction in platform vibration introduced by mechanically steerable devices. In this research, we investigate how modeling of these antennas can be introduced into out overall simulation and modeling structure. The ultimate goal of this research is two-fold. First, to enable NASA engineers to model various proposed simulation architectures and determine which proposed architecture meets the given architectural requirements. Second, given a set of communications link requirements for a proposed satellite architecture, determine the optimal configuration for a phased array antenna. There is a variety of tools available that can be used to model phased array antennas. To meet our stated goals, the first objective of this research is to compare the subset of tools available to us

  11. Measuring Phased-Array Antenna Beampatterns with High Dynamic Range for the Murchison Widefield Array using 137 MHz ORBCOMM Satellites

    CERN Document Server

    Neben, A R; Hewitt, J N; Bernardi, G; Bowman, J D; Briggs, F; Cappallo, R J; Deshpande, A A; Goeke, R; Greenhill, L J; Hazelton, B J; Johnston-Hollitt, M; Kaplan, D L; Lonsdale, C J; McWhirter, S R; Mitchell, D A; Morales, M F; Morgan, E; Oberoi, D; Ord, S M; Prabu, T; Shankar, N Udaya; Srivani, K S; Subrahmanyan, R; Tingay, S J; Wayth, R B; Webster, R L; Williams, A; Williams, C L

    2015-01-01

    Detection of the fluctuations in 21 cm line emission from neutral hydrogen during the Epoch of Reionization in thousand hour integrations poses stringent requirements on calibration and image quality, both of which necessitate accurate primary beam models. The Murchison Widefield Array (MWA) uses phased array antenna elements which maximize collecting area at the cost of complexity. To quantify their performance, we have developed a novel beam measurement system using the 137 MHz ORBCOMM satellite constellation and a reference dipole antenna. Using power ratio measurements, we measure the {\\it in situ} beampattern of the MWA antenna tile relative to that of the reference antenna, canceling the variation of satellite flux or polarization with time. We employ angular averaging to mitigate multipath effects (ground scattering), and assess environmental systematics with a null experiment in which the MWA tile is replaced with a second reference dipole. We achieve beam measurements over 30 dB dynamic range in beam...

  12. Phase Residual Estimations for PCVs of Spaceborne GPS Receiver Antenna and Their Impacts on Precise Orbit Determination of GRACE Satellites

    Institute of Scientific and Technical Information of China (English)

    TU Jia; GU Defeng; WU Yi; YI Dongyun

    2012-01-01

    In-flight phase center systematic errors of global positioning system (GPS) receiver antenna are the main restriction for improving the precision of precise orbit determination using dual-frequency GPS.Residual approach is one of the valid methods for in-flight calibration of GPS receiver antenna phase center variations (PCVs) from ground calibration.In this paper,followed by the correction model of spaceborne GPS receiver antenna phase center,ionosphere-free PCVs can be directly estimated by ionosphere-free carrier phase post-fit residuals of reduced dynamic orbit determination.By the data processing of gravity recovery and climate experiment (GRACE) satellites,the following conclusions are drawn.Firstly,the distributions of ionosphere-free carrier phase post-fit residuals from different periods have the similar systematic characteristics.Secondly,simulations show that the influence of phase residual estimations for ionosphere-free PCVs on orbit determination can reach the centimeter level.Finally,it is shown by in-flight data processing that phase residual estimations of current period could not only be used for the calibration for GPS receiver antenna phase center of foretime and current period,but also be used for the forecast of ionosphere-free PCVs in future period,and the accuracy of orbit determination can be well improved.

  13. Low-Cost Planar MM-Wave Phased Array Antenna for Use in Mobile Satellite (MSAT) Platforms

    DEFF Research Database (Denmark)

    Ojaroudiparchin, Naser; Shen, Ming; Pedersen, Gert F.

    2015-01-01

    In this paper, a compact 8×8 phased array antenna for mobile satellite (MSAT) devices is designed and investigated. 64-elements of 22 GHz patch antennas with coaxial-probe feeds have been used for the proposed planar design. The antenna is designed on a low-cost FR4 substrate with thickness......, dielectric constant, and loss tangent of 0.8 mm, 4.3, and 0.025, respectively. The antenna exhibits good performance in terms of impedance- matching, gain and efficiency characteristics, even though it is designed using high loss substrate with compact dimension (Wsub×Lsub=55×55 mm2). The antenna has more...... than 23 dB realized gain and -0.8 dB radiation efficiency when its beam is tilted to 0o elevation. The center frequency of the designed array can be controlled by adjusting the values of the antenna parameters. Compared with the previous designs, the proposed planar phased array has the advantages...

  14. Land vehicle antennas for satellite mobile communications

    Science.gov (United States)

    Haddad, H. A.; Pieper, B. V.; Mckenna, D. B.

    1985-01-01

    The RF performance, size, pointing system, and cost were investigated concepts are: for a mechanically steered 1 x 4 tilted microstrip array, a mechanically steered fixed-beam conformal array, and an electronically steered conformal phased array. Emphasis is on the RF performance of the tilted 1 x 4 antenna array and methods for pointing the various antennas studied to a geosynchronous satellite. An updated version of satellite isolations in a two-satellite system is presented. Cost estimates for the antennas in quantities of 10,000 and 100,000 unites are summarized.

  15. Living antennas on communication satellites

    DEFF Research Database (Denmark)

    Lumholt, Michael

    2003-01-01

    Crises change the global pattern of communication. The communications problems occur because the satellites are optimized to cover specific geographic areas, and these areas cannot be altered once the satellites are in Earth orbit. An effective solution to the problem is to equip communication...... satellites with "living" antennas that can adjust their radiation coverage areas according to the new demands. The development of living antennas is, therefore, among the focus areas identified and supported by the European Space Agency, ESA....

  16. Integrated Solar Panel Antennas for Cube Satellites

    OpenAIRE

    Mahmoud, Mahmoud N.

    2010-01-01

    This thesis work presents an innovative solution for small satellite antennas by integrating slot antennas and solar cells on the same panel to save small satellite surface real estate and to replace deployed wire antennas for certain operational frequencies. The two main advantages of the proposed antenna are: 1) the antenna does not require an expensive deployment mechanism that is required by dipole antennas; 2) the antenna does not occupy as much valuable surface real estate as patch ante...

  17. Integrated Solar Panel Antennas for Cube Satellites

    OpenAIRE

    Mahmoud, Mahmoud N.

    2010-01-01

    This thesis work presents an innovative solution for small satellite antennas by integrating slot antennas and solar cells on the same panel to save small satellite surface real estate and to replace deployed wire antennas for certain operational frequencies. The two main advantages of the proposed antenna are: 1) the antenna does not require an expensive deployment mechanism that is required by dipole antennas; 2) the antenna does not occupy as much valuable surface real estate as patch ante...

  18. Architectures for ku-band broadband airborne satellite communication antennas

    NARCIS (Netherlands)

    Verpoorte, Jaco; Schippers, Harmen; Jorna, Pieter; Roeloffzen, Chris G.H.; Marpaung, David A.I.; Baggen, Rens; Sanadgol, Bahram

    2010-01-01

    This paper describes different architectures for a broadband antenna for satellite communication on aircraft. The antenna is a steerable (conformal) phased array antenna in Ku-band (receive-only). First the requirements for such a system are addressed. Subsequently a number of potential architecture

  19. Hybrid Maritime Satellite Communication Antenna

    DEFF Research Database (Denmark)

    Smith, Thomas Gunst

    Hybrid antennas for a maritime satellite communication terminal with simultaneous operation at L- and Ka-band have been investigated. The frequency bands of interest are 1; 525:0 1; 660:5 MHz (RX+TX, RHCP), 19:7 20:2 (RX, LHCP) and 29:5 30:0 GHz (TX, RHCP), which are all part of the Inmarsat BGAN...

  20. Vehicle antenna development for mobile satellite applications

    Science.gov (United States)

    Woo, K.

    1988-01-01

    The paper summarizes results of a vehicle antenna program at JPL in support of a developing U.S. mobile satellite services (MSS) designed to provide telephone and data services for the continental United States. Two classes of circularly polarized vehicle antennas have been considered for the MSS: medium-gain, satellite-tracking antennas with 10-12-dBic gain; and low-gain, azimuthally omnidirectional antennas with 3-5-dBic gain. The design and performance of these antennas are described, and the two antennas are shown to have peculiar advantages and disadvantages.

  1. Phase shifter for antenna beam steering

    Science.gov (United States)

    Jindal, Ravi; Razban, Tchanguiz

    2016-03-01

    Wide band Array Antenna operates in Ku-band (10.7-12.7 GHz) frequency composed of N×N radiating elements. This antenna aims at the reception of television satellite signals. The goal of this research is to provide better possibility of electronic beam control instead of manual or mechanical control, and design compact and low cost phase shifters to be inserted in the feeding network of this antenna. The electronic control of the phase shifter will allow the control of beam steering. The emphasis of this project will be done at the beginning on the design of a good phase shifter in Ku band. The aim of this research is to define, simulate, release and measure a continuous phase shifter. Better reflection loss, low transmission loss, low Cost of array antennas, large range of phase-shifter, phase flatness and bandwidth will be achieved by providing better gain.

  2. Phase shifter for antenna beam steering

    Energy Technology Data Exchange (ETDEWEB)

    Jindal, Ravi, E-mail: rjindal21@gmail.com [Master’s(MS) in System Electronics and General Electrical, Ecole Polytechnique of university of Nantes France, IETR, Nantes (France); Razban, Tchanguiz, E-mail: tchanguiz.razban-haghighi@univ-nantes.fr [Electronics and Telecommunication Institute of Rennes (IETR-UMR 6164), Ecole Polytechnique of university of Nantes France, IETR, Nantes (France)

    2016-03-09

    Wide band Array Antenna operates in Ku-band (10.7-12.7 GHz) frequency composed of N×N radiating elements. This antenna aims at the reception of television satellite signals. The goal of this research is to provide better possibility of electronic beam control instead of manual or mechanical control, and design compact and low cost phase shifters to be inserted in the feeding network of this antenna. The electronic control of the phase shifter will allow the control of beam steering. The emphasis of this project will be done at the beginning on the design of a good phase shifter in Ku band. The aim of this research is to define, simulate, release and measure a continuous phase shifter. Better reflection loss, low transmission loss, low Cost of array antennas, large range of phase-shifter, phase flatness and bandwidth will be achieved by providing better gain.

  3. Mobile satellite communications - Vehicle antenna technology update

    Science.gov (United States)

    Bell, D.; Naderi, F. M.

    1986-01-01

    This paper discusses options for vehicle antennas to be used in mobile satellite communications systems. Two types of antennas are identified. A non-steerable, azimuthally omnidirectional antenna with a modest gain of 3 to 5 dBi is suggested when a low cost is desired. Alternatively, mechanically or electronically steerable antennas with a higher gain of 10 to 12 dBi are suggested to alleviate power and spectrum scarcity associated with mobile satellite communications. For steerable antennas, both open-loop and closed-loop pointing schemes are discussed. Monopulse and sequential lobing are proposed for the mechanically steered and electronically steered antennas, respectively. This paper suggests a hybrid open-loop/closed-loop pointing technique as the best performer in the mobile satellite environment.

  4. Satellite antenna layout and optimization in electromagnetic compatibility design

    Science.gov (United States)

    Zhang, Jinshuo; Xie, Shuguo; Liu, Yan

    2009-12-01

    This paper firstly analyzes the main factors that impact the layout of satellite antenna. The uniform geometrical theory of diffraction (UTD) is used to establish mathematical model for calculating the coupling of satellite antenna, and set up the objective function of the placement optimization. The genetic algorithm incorporating high-frequency simulation to minimize antenna coupling by optimally positioning satellite antenna is described in detail. The results of antenna placement on a realistic satellite show that this method is effective in the optimal design of satellite antenna layout for the purpose of electromagnetic compatibility.

  5. Development of a broadband and squint-free Ku-band phased array antenna system for airborne satellite communications

    NARCIS (Netherlands)

    Marpaung, D.A.I.; Roeloffzen, C.G.H.; Beeker, W.P.; Beeker, Willem; Noharet, Bertrand; Verpoorte, Jaco; Baggen, Rens

    Novel avionic communication systems are required for various purposes, for example to increase the flight safety and operational integrity as well as to enhance the quality of service to passengers on board. To serve these purposes, a key technology that is essential to be developed is an antenna

  6. Low Cost Antennas for Direct Broadcast Satellite Radio

    Science.gov (United States)

    Wu, T. K.; Huang, J.

    1994-01-01

    Two omni-directional and circularly polarized low gain antennas (the crossed drooping dipole and the TM(sub 21) mode circular patch antenna)are developed for direct broadcast satellite radio (DBSR) outdoor mobile terminal applications.

  7. Reliable Control of Ship-mounted Satellite Tracking Antenna

    DEFF Research Database (Denmark)

    Soltani, Mohsen; Izadi-Zamanabadi, Roozbeh; Wisniewski, Rafal

    2010-01-01

    Motorized antenna is a key element in overseas satellite telecommunication. The control system directs the on-board antenna toward a chosen satellitewhile the high sea waves disturb the antenna. Certain faults (communication system malfunction or signal blocking) cause interruption in the communi......Motorized antenna is a key element in overseas satellite telecommunication. The control system directs the on-board antenna toward a chosen satellitewhile the high sea waves disturb the antenna. Certain faults (communication system malfunction or signal blocking) cause interruption...

  8. High Precision Control of Ship-Mounted Satellite Tracking Antenna

    DEFF Research Database (Denmark)

    Mohsen, Soltani; Izadi-Zamanabadi, Roozbeh; Wisniewski, Rafal

    2007-01-01

    The telecommunication on a modern merchandise ship is maintained by means of satellite communication. The task of the tracking system is to position the on-board antenna toward a chosen satellite. The control system is capable of rejecting the external disturbances which affect on the under......-actuated antenna and ensures that it remains locked on the satellite. In this paper, a nonlinear internal model controller (NIMC), which achieves asymptotic tracking for the nonlinear antenna system with nonlinear exogenous dynamics, is proposed. Computer simulations as well as practical tests verify...... the effectiveness of this method to cope with the external disturbances that are imposed to the satellite tracking antenna (STA)....

  9. High Precision Control of Ship-Mounted Satellite Tracking Antenna

    DEFF Research Database (Denmark)

    Mohsen, Soltani; Izadi-Zamanabadi, Roozbeh; Wisniewski, Rafal

    2007-01-01

    The telecommunication on a modern merchandise ship is maintained by means of satellite communication. The task of the tracking system is to position the on-board antenna toward a chosen satellite. The control system is capable of rejecting the external disturbances which affect on the under......-actuated antenna and ensures that it remains locked on the satellite. In this paper, a nonlinear internal model controller (NIMC), which achieves asymptotic tracking for the nonlinear antenna system with nonlinear exogenous dynamics, is proposed. Computer simulations as well as practical tests verify...... the effectiveness of this method to cope with the external disturbances that are imposed to the satellite tracking antenna (STA)....

  10. EHF multifunction phased array antenna

    Science.gov (United States)

    Solbach, Klaus

    1986-07-01

    The design of a low cost demonstration EHF multifunction-phased array antenna is described. Both, the radiating elements and the phase-shifter circuits are realized on microstrip substrate material in order to allow photolithographic batch fabrication. Self-encapsulated beam-lead PIN-diodes are employed as the electronic switch elements to avoid expensive hermetic encapsulation of the semiconductors or complete circuits. A space-feed using a horn-radiator to illuminate the array from the front-side is found to be the simplest and most inexpensive feed. The phased array antenna thus operates as a reflect-array, the antenna elements employed in a dual role for the collection of energy from the feed-horn and for the re-radiation of the phase-shifted waves (in transmit-mode). The antenna is divided into modules containing the radiator/phase-shifter plate plus drive- and BITE-circuitry at the back. Both drive- and BITE-components use gate-array integrated circuits especially designed for the purpose. Several bus-systems are used to supply bias and logical data flows to the modules. The beam-steering unit utilizes several signal processors and high-speed discrete adder circuits to combine the pointing, frequency and beam-shape information from the radar system computer with the stored phase-shift codes for the array elements. Since space, weight and power consumption are prime considerations only the most advanced technology is used in the design of both the microwave and the digital/drive circuitry.

  11. Novel Ku Band Reflectarray Antenna for Satellite Communication

    Directory of Open Access Journals (Sweden)

    Sridhar Bilvam

    2014-04-01

    Full Text Available This study focuses on the design and analysis of Ku band reflectarray antenna using a novel crossed dumbbell (clover patch unit cell. The reflectarray is proposed for application in satellite communication more specifically for Satellite newsgathering (12.5-13.75 GHz. The clover shaped unit cell is designed for 13.07 GHz and the suitability of the unit cell is validated using the phase characteristics analysis. The effect of the elements on the performance represented by the range of the reflection phase is of prime importance. From the observation, Clover unit cell has large phase variation compared to minkowski and koch unit cells. Therefore, the main purpose of this study is to investigate and validate the novel unit cell with a wide phase characteristics and the reflectarray constructed.

  12. Flat Array Antennas for Ku-Band Mobile Satellite Terminals

    Directory of Open Access Journals (Sweden)

    Roberto Vincenti Gatti

    2009-01-01

    Full Text Available This work presents the advances in the development of two innovative flat array antennas for Ku-band mobile satellite terminals. The first antenna is specifically conceived for double-deck trains to allow a bi-directional high data rate satellite link. The available circular surface (diameter 80 cm integrates both a transmitting and a receiving section, operating in orthogonal linear polarizations. The TX frequency range is fully covered while the RX bandwidth is around 1 GHz arbitrarily allocated on the DVB range depending on requirements. The beam is steered in elevation through a phased array architecture not employing costly phase shifters, while the steering in azimuth is mechanical. Active BFNs allow excellent performance in terms of EIRP and G/T, maintaining extremely low profile. High antenna efficiency and low fabrication cost are ensured by the employment of innovative SIW (Substrate Integrated Waveguide structures. The second antenna, receiving-only, is designed for radio/video streaming services in mobile environment. Full DVB coverage is achieved thanks to cavity-backed patches operating in double linear polarization. Two independent broadband active BFNs allow simultaneous reception of both polarizations with full tracking capabilities and a squintless beam steering from 20∘ to 60∘ in elevation. A minimum gain of 20 dBi and G/T >−3 dB/∘K are achieved, while maintaining extremely compact size and flat profile. In the design of both antennas fabrication cost is considered as a driving factor, yet providing high performance with a flat profile and thus resulting in a great commercial potentiality.

  13. Omnidirectional antenna having constant phase

    Energy Technology Data Exchange (ETDEWEB)

    Sena, Matthew

    2017-04-04

    Various technologies presented herein relate to constructing and/or operating an antenna having an omnidirectional electrical field of constant phase. The antenna comprises an upper plate made up of multiple conductive rings, a lower ground-plane plate, a plurality of grounding posts, a conical feed, and a radio frequency (RF) feed connector. The upper plate has a multi-ring configuration comprising a large outer ring and several smaller rings of equal size located within the outer ring. The large outer ring and the four smaller rings have the same cross-section. The grounding posts ground the upper plate to the lower plate while maintaining a required spacing/parallelism therebetween.

  14. Evolutionary Design of a Phased Array Antenna Element

    Science.gov (United States)

    Globus, Al; Linden, Derek; Lohn, Jason

    2006-01-01

    We present an evolved S-band phased array antenna element design that meets the requirements of NASA's TDRS-C communications satellite scheduled for launch early next decade. The original specification called for two types of elements, one for receive only and one for transmit/receive. We were able to evolve a single element design that meets both specifications thereby simplifying the antenna and reducing testing and integration costs. The highest performance antenna found using a genetic algorithm and stochastic hill-climbing has been fabricated and tested. Laboratory results are largely consistent with simulation. Researchers have been investigating evolutionary antenna design and optimization since the early 1990s, and the field has grown in recent years its computer speed has increased and electromagnetic simulators have improved. Many antenna types have been investigated, including wire antennas, antenna arrays and quadrifilar helical antennas. In particular, our laboratory evolved a wire antenna design for NASA's Space Technology 5 (ST5) spacecraft. This antenna has been fabricated, tested, and is scheduled for launch on the three spacecraft in 2006.

  15. Multi-antenna synchronized global navigation satellite system receiver and its advantages in high-precision positioning applications

    Science.gov (United States)

    Dong, Danan; Chen, Wen; Cai, Miaomiao; Zhou, Feng; Wang, Minghua; Yu, Chao; Zheng, Zhengqi; Wang, Yuanfei

    2016-12-01

    The multi-antenna synchronized global navigation satellite system receiver is a high precision, low cost, and widely used emerging receiver. Using this type of receiver, the satellite and receiver clock errors can be eliminated simultaneously by forming between antenna single-differences, which is equivalent to the conventional double-difference model. However, current multi-antenna synchronized global navigation satellite system receiver products have not fully realized their potential to achieve better accuracy, efficiency, and broader applications. This paper introduces the conceptual design and derivable products of multi-antenna synchronized global navigation satellite system receivers involving the aspects of attitude determination, multipath effect mitigation, phase center variation correction, and ground-based carrier phase windup calibration. Through case studies, the advantages of multi-antenna synchronized global navigation satellite system receivers in high-precision positioning applications are demonstrated.

  16. Concepts and cost trade-offs for land vehicle antennas in satellite mobile communications

    Science.gov (United States)

    Haddad, H. A.

    1948-01-01

    Several antenna design concepts, operating at UHF (821 to 825 MHz transmit and 866 to 870 MHz receive bands), with gain ranging between 6 and 12 dBic, that are suitable for land mobile vehicles are presented. The antennas may be used within CONUS and ALASKA to communicate to and from a geosynchronous satellite. Depending on the type of steering mechanism, the antennas are broken down into three categories; (1) electronically scanned arrays with phase shifters, (2) electronically switched arrays with switchable power dividers/combiners, and (3) mechanically steered arrays. The operating characteristics of two of these design concepts, one a conformal antenna with electronic beam steering and the other a nonconformal design with mechanical steering, were evaluated with regard to two and three satellite system. Cost estimates of various antenna concepts were made and plotted against their overall gain performance.

  17. Thermal deformation analysis of the composite material satellite antenna

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Controlling the thermal deformation is a crucial index for the design of the satellite antenna. To calculate and measure the satellite antenna's thermal deformation is also an important step for the design of satellite antenna. Based on the foundation of equivalent assumption, the thermal deformation of the parabolic satellite antenna was analyzed by the finite element method for different design project. The best design project that had the minimum of the thermal deformation could be obtained through changing the lay-angle, lay-layers and lay-thickness of each layer. Results show the asymmetry structure has the minimum of thermal deformation. This paper may provide useful information for the further investigation on the coupling of thermal-stress structure.

  18. Development of 30/20 GHz satellite antenna structures

    Science.gov (United States)

    Minomo, M.; Yasaka, T.

    1986-08-01

    An antenna structural design for a large capacity communication satellite using 13 beams in the 30/20GHz frequency bands is discussed. This design is to be utilized in developing a more cost effective domestic satellite communication system for Japan. This system requires 2 high precision deployable antennas with projected aperture diameters of 3.5m at 20GHz and 2.5m at 30GHz. The in-orbit demonstration will use the ETS-6 satellite. Based on experience in the development of spaceborne antennas for 30/20GHz bands (e.g., for the CS-2 and CS-3 satellites) activities in structural design of high precision deployable antennas show the truss reflector structure is promising for achieving required structural properties.

  19. Integrated After-Market Solar Panel Antennas for Small Satellites

    OpenAIRE

    Turpin, Timothy; Mahmoud, Mahmoud; Baktur, Reyhan; Furse, Cynthia

    2009-01-01

    The majority of surface area on a small satellite is taken up by solar panels for power. Integrating antennas with solar panels, would save a valuable amount of satellite surface area, and thus directly contribute to the size reduction and multi-functionality of solar panel. Furthermore, such integration does not require deployed mechanism and therefore is cost-friendly design.Two types of integrations are presented in this paper. The first type is to place optically transparent antennas dire...

  20. Integrated After-Market Solar Panel Antennas for Small Satellites

    OpenAIRE

    Turpin, Timothy; Mahmoud, Mahmoud; Baktur, Reyhan; Furse, Cynthia

    2009-01-01

    The majority of surface area on a small satellite is taken up by solar panels for power. Integrating antennas with solar panels, would save a valuable amount of satellite surface area, and thus directly contribute to the size reduction and multi-functionality of solar panel. Furthermore, such integration does not require deployed mechanism and therefore is cost-friendly design.Two types of integrations are presented in this paper. The first type is to place optically transparent antennas dire...

  1. Low Cost Phased Array Antenna System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — JEM Engineering proved the technical feasibility of the FlexScan array?a very low-cost, highly-efficient, wideband phased array antenna?in Phase I, and stands ready...

  2. Synthesis of Phased Cylindrical Arc Antenna Arrays

    Directory of Open Access Journals (Sweden)

    Hussein Rammal

    2009-01-01

    Full Text Available This paper describes a new approach to synthesize cylindrical antenna arrays controlled by the phase excitation, to synthesize directive lobe and multilobe patterns with steered zero. The proposed method is based on iterative minimization of a function that incorporates constraints imposed in each direction. An 8-element cylindrical antenna has been simulated and tested for various types of beam configurations.

  3. An Antenna Tracking Method Using Phased Array and Servo for Vehicle Satellite Communication on the Move%相控阵结合伺服辅助的车载动中通天线跟踪方法

    Institute of Scientific and Technical Information of China (English)

    蒋文丰

    2016-01-01

    天线跟踪功能是车载动中通系统( SOTM)提供无线通信能力的前提,相控阵天线能提供较好的跟踪性能,但是存在波束扫描范围有限的问题。为实现相控阵天线全方位跟踪能力,提出了一种相控阵+伺服辅助的方法。给出了算法数据处理流程,并完成了原理样机设计。根据原理样机工作原理给出了跟踪角误差计算公式,测试结果与计算结果相符。测试结果表明:在(57.88~115.76)。/s角速度下,通信链路信噪比损失小于0.5 dB。%The antenna tracking function is the foundation for the vehicle satellite communication on the move( SOTM) to offer wireless communications,and the phased array antenna can provide better tracking performance,but the beam scanning range is limited. In order to realize the phased array antenna tracking in the entire orientation,a method using phased array antenna and servo is presented. The data processing flow of algorithm is provided, and the prototype has been developed. According to the prototype working principle,the formula to calculate the tracking angle error is given. The test result matches with the calcu-lating result,and the signal-to-noise ratio(SNR) loss is smaller than 0. 5 dB at the angle speed between (57. 88~115. 76)./s.

  4. Array antennas design in dependence of element-phasing

    Science.gov (United States)

    Zichner, R.; Chandra, M.

    2009-05-01

    Array antennas are used in science as well as for commercial and military purposes. The used element antennas act in accordance to their desired uses, for example radars or stationer GPS satellites. Typical components are for example slotted waveguides, patches, yagi-antennas and helix-antennas. All these elements do stand out with their own characteristics based on their special applications. If these elements are formed into an array configuration, the effectiveness can be improved immensely. There is a relation between the array functions and the physical array properties like the element alignment (linear, planar, circular), distances between the elements and so on. Among the physical properties there are other attributes like phase or amplitude coefficients, which are of great significance. The aim of this study was to provide an insight into the problem of array design, as far as the antenna element phase is concerned. Along with this, array radiation characteristics effects are presented. With the help of the extracted cognitions beam forming behaviour can be shown and the array phase behaviour can be analysed. One of the main applications is to simulate the array characteristics, like the radiation characteristic or the gain, for displacements of the array feeding point. A software solution that simulates the phase shift of a given array pattern is sought to adjust the feeding point.

  5. Array antennas design in dependence of element-phasing

    Directory of Open Access Journals (Sweden)

    R. Zichner

    2009-05-01

    Full Text Available Array antennas are used in science as well as for commercial and military purposes. The used element antennas act in accordance to their desired uses, for example radars or stationer GPS satellites. Typical components are for example slotted waveguides, patches, yagi-antennas and helix-antennas. All these elements do stand out with their own characteristics based on their special applications. If these elements are formed into an array configuration, the effectiveness can be improved immensely. There is a relation between the array functions and the physical array properties like the element alignment (linear, planar, circular, distances between the elements and so on. Among the physical properties there are other attributes like phase or amplitude coefficients, which are of great significance. The aim of this study was to provide an insight into the problem of array design, as far as the antenna element phase is concerned. Along with this, array radiation characteristics effects are presented. With the help of the extracted cognitions beam forming behaviour can be shown and the array phase behaviour can be analysed. One of the main applications is to simulate the array characteristics, like the radiation characteristic or the gain, for displacements of the array feeding point. A software solution that simulates the phase shift of a given array pattern is sought to adjust the feeding point.

  6. Phased array antenna element for automotive radar application

    OpenAIRE

    2014-01-01

    In this thesis work, a design of reliable antenna front-end for W band automotive radar is studied and the problems and considerations associated with phased array antenna design at W-band are addressed. Proposed phased array antenna consists of on chip patch antenna which has the advantages of being integrated by the active circuitry. A sample of patch antenna and patch array are designed and fabricated to be tested for their functionality. Printing antenna on Silicon substrate is a compact ...

  7. A multifunctional solar panel antenna for cube satellites

    Science.gov (United States)

    Fawole, Olutosin C.

    The basic cube satellite (CubeSat) is a modern small satellite that has a standard size of about one liter (the 1U CubeSat). Three 1U CubeSats could be stacked to form a 3U CubeSat. Their low-cost, short development time, and ease of deployment make CubeSats popular for space research, geographical information gathering, and communication applications. An antenna is a key part of the CubeSat communication subsystem. Traditionally, antennas used on CubeSats are wrapped-up wire dipole antennas, which are deployed after satellite launch. Another antenna type used on CubeSats is the patch antenna. In addition to their low gain and efficiency, deployable dipole antennas may also fail to deploy on satellite launch. On the other hand, a solid patch antenna will compete for space with solar cells when placed on a CubeSat face, interfering with satellite power generation. Slot antennas are promising alternatives to dipole and patch antennas on CubeSats. When excited, a thin slot aperture etched on a conductive sheet (ground plane) is an efficient bidirectional radiator. This open slot antenna can be backed by a reflector or cavity for unidirectional radiation, and solar cells can be placed in spaces on the ground plane not occupied by the slot. The large surface areas of 3U CubeSats can be exploited for a multifunctional antenna by integrating multiple thin slot radiators, which are backed by a thin cavity on the CubeSat surfaces. Solar cells can then be integrated on the antenna surface. Polarization diversity and frequency diversity improve the overall performance of a communication system. Having a single radiating structure that could provide these diversities is desired. It has been demonstrated that when a probe excites a square cavity with two unequal length crossed-slots, the differential radiation from the two slots combines in the far-field to yield circular polarization. In addition, it has been shown that two equal-length proximal slots, when both fed with a

  8. Advanced Communication Technology Satellite (ACTS) multibeam antenna technology verification experiments

    Science.gov (United States)

    Acosta, Roberto J.; Larko, Jeffrey M.; Lagin, Alan R.

    1992-01-01

    The Advanced Communication Technology Satellite (ACTS) is a key to reaching NASA's goal of developing high-risk, advanced communications technology using multiple frequency bands to support the nation's future communication needs. Using the multiple, dynamic hopping spot beams, and advanced on board switching and processing systems, ACTS will open a new era in communications satellite technology. One of the key technologies to be validated as part of the ACTS program is the multibeam antenna with rapidly reconfigurable hopping and fixed spot beam to serve users equipped with small-aperature terminals within the coverage areas. The proposed antenna technology experiments are designed to evaluate in-orbit ACTS multibeam antenna performance (radiation pattern, gain, cross pol levels, etc.).

  9. Design and Analysis of HJ-1-C Satellite SAR Antenna

    Directory of Open Access Journals (Sweden)

    Zheng Shi-kun

    2014-06-01

    Full Text Available With truss deployable mesh parabolic reflector, the HJ-1-C SAR antenna has complex structure and multiple steps during the deployed processing. The design of the antenna is difficult in terms of deployed reliability and electrical performance. This paper makes intensive research on system, structure and electrical design, and the analysis of mechanical and thermal performance in the actual space conditions is also presented. The successful deploying in orbit and high image quality of the HJ-1-C satellite indicate that the mechanical, electronic, thermal and reliability design of the antenna satisfy the project requirement, and these research provides valuable experience for the design of the centralized mesh parabolic SAR antenna.

  10. Multiband Photonic Phased-Array Antenna

    Science.gov (United States)

    Tang, Suning

    2015-01-01

    A multiband phased-array antenna (PAA) can reduce the number of antennas on shipboard platforms while offering significantly improved performance. Crystal Research, Inc., has developed a multiband photonic antenna that is based on a high-speed, optical, true-time-delay beamformer. It is capable of simultaneously steering multiple independent radio frequency (RF) beams in less than 1,000 nanoseconds. This high steering speed is 3 orders of magnitude faster than any existing optical beamformer. Unlike other approaches, this technology uses a single controlling device per operation band, eliminating the need for massive optical switches, laser diodes, and fiber Bragg gratings. More importantly, only one beamformer is needed for all antenna elements.

  11. Sunflower array antenna for multi-beam satellite applications

    NARCIS (Netherlands)

    Vigano, M.C.

    2011-01-01

    Saving space on board, reducing costs and improving the antenna performances are tasks of outmost importance in the field of satellite communication. In this work it is shown how a non-uniformly spaced, direct radiating array designed according to the so called ‘sunflower’ law is able to satisfy str

  12. Absolute IGS antenna phase center model igs08.atx: status and potential improvements

    Science.gov (United States)

    Schmid, R.; Dach, R.; Collilieux, X.; Jäggi, A.; Schmitz, M.; Dilssner, F.

    2016-04-01

    On 17 April 2011, all analysis centers (ACs) of the International GNSS Service (IGS) adopted the reference frame realization IGS08 and the corresponding absolute antenna phase center model igs08.atx for their routine analyses. The latter consists of an updated set of receiver and satellite antenna phase center offsets and variations (PCOs and PCVs). An update of the model was necessary due to the difference of about 1 ppb in the terrestrial scale between two consecutive realizations of the International Terrestrial Reference Frame (ITRF2008 vs. ITRF2005), as that parameter is highly correlated with the GNSS satellite antenna PCO components in the radial direction.

  13. Microstrip Yagi array antenna for mobile satellite vehicle application

    Science.gov (United States)

    Huang, John; Densmore, Arthur C.

    1991-01-01

    A novel antenna structure formed by combining the Yagi-Uda array concept and the microstrip radiator technique is discussed. This antenna, called the microstrip Yagi array, has been developed for the mobile satellite (MSAT) system as a low-profile, low-cost, and mechanically steered medium-gain land-vehicle antenna. With the antenna's active patches (driven elements) and parasitic patches (reflector and director elements) located on the same horizontal plane, the main beam of the array can be tilted, by the effect of mutual coupling, in the elevation direction providing optimal coverage for users in the continental United States. Because the parasitic patches are not connected to any of the lossy RF power distributing circuit the antenna is an efficient radiating system. With the complete monopulse beamforming and power distributing circuits etched on a single thin stripline board underneath the microstrip Yagi array, the overall L-band antenna system has achieved a very low profile for vehicle's rooftop mounting, as well as a low manufacturing cost. Experimental results demonstrate the performance of this antenna.

  14. Application of adaptive antenna techniques to future commercial satellite communication

    Science.gov (United States)

    Ersoy, L.; Lee, E. A.; Matthews, E. W.

    1987-01-01

    The purpose of this contract was to identify the application of adaptive antenna technique in future operational commercial satellite communication systems and to quantify potential benefits. The contract consisted of two major subtasks. Task 1, Assessment of Future Commercial Satellite System Requirements, was generally referred to as the Adaptive section. Task 2 dealt with Pointing Error Compensation Study for a Multiple Scanning/Fixed Spot Beam Reflector Antenna System and was referred to as the reconfigurable system. Each of these tasks was further sub-divided into smaller subtasks. It should also be noted that the reconfigurable system is usually defined as an open-loop system while the adaptive system is a closed-loop system. The differences between the open- and closed-loop systems were defined. Both the adaptive and reconfigurable systems were explained and the potential applications of such systems were presented in the context of commercial communication satellite systems.

  15. Microwave power transmitting phased array antenna research project

    Science.gov (United States)

    Dickinson, R. M.

    1978-01-01

    An initial design study and the development results of an S band RF power transmitting phased array antenna experiment system are presented. The array was to be designed, constructed and instrumented to permit wireless power transmission technology evaluation measurements. The planned measurements were to provide data relative to the achievable performance in the state of the art of flexible surface, retrodirective arrays, as a step in technically evaluating the satellite power system concept for importing to earth, via microwave beams, the nearly continuous solar power available in geosynchronous orbit. Details of the microwave power transmitting phased array design, instrumentation approaches, system block diagrams, and measured component and breadboard characteristics achieved are presented.

  16. Phase Noise in Photonic Phased-Array Antenna Systems

    Science.gov (United States)

    Logan, Ronald T., Jr.; Maleki, Lute

    1998-01-01

    The total noise of a phased-array antenna system employing a photonic feed network is analyzed using a model for the individual component noise including both additive and multiplicative equivalent noise generators.

  17. On intermodulation beams of satellite DBF transmitting multibeam array antenna

    Science.gov (United States)

    Zhao, Hongmei; Wang, Huali; Mu, Shanxiang

    2007-11-01

    Digital beamforming (DBF) transmitting multibeam planar array antenna with nonlinear behaviors of solid-state power amplifiers (SSPA) is discussed. This paper investigates the intermodulation beams produced by the nonlinearity characteristics of the SSPA with multiple carrier components. The Shimbo model is simplified to describe the nonlinear behaviors of SSPA. The optimal SSPA input back-off (IBO) point which is given the desired the carrier and the intermodulatin ratio (C/IM) is simulated. And the tradeoffs between linearity and efficiency of the power amplifier which influence this IBO is also discussed, helping to selecting suitable SSPA device and reducing the dc power consumption in satellite array antenna system.

  18. Directional Pattern Analysis of a Linear Phased Antenna

    Directory of Open Access Journals (Sweden)

    Jan Haring

    2008-01-01

    Full Text Available An antenna array is a system compound from simply radiators (dipoles, microstrip antennas, that together form desired radiation pattern. Phased array antennas consist of multiple stationary antenna elements, that are fed coherently and use variable phase or time-delay control at each element to scan a beam to given angles in space. Variable amplitude control is sometimes also provided for antenna pattern shaping.

  19. Development of an integrated photonic beamformer for electronically-steered Ku-band phased array antenna

    NARCIS (Netherlands)

    Zhuang, L.; Marpaung, D.A.I.; Burla, M.; Boot, R.; Hulzinga, A.; Beeker, W.P.; Beeker, Willem; van Dijk, P.; Roeloffzen, C.G.H.

    2011-01-01

    Currently an integrated photonic beamformer for electronically-steered Ku-band phased array antenna (PAA) system for satellite communications is being developed within a Dutch Point One R&D Innovation Project “Broadband Satellite Communication Services on High-Speed Transport Vehicles‿, targeting

  20. Design and characteristics of a multiband communication satellite antenna system

    Science.gov (United States)

    Ueno, Kenji; Itanami, Takao; Kumazawa, Hiroyuki; Ohtomo, Isao

    1995-04-01

    Feasibility studies on a multiband communication satellite antenna system and the key technologies involved in devising this system are described. The proposed multiband communication satellite utilizes four frequency bands: Ka (30/20 GHz), Ku (14/12 GHz), C (6/4 GHz), and S (2.6/2.5 GHz). It has six beam configurations, three multibeam and three shaped-beam. The following key technologies are presented: (1) a low-loss frequency selective subreflector (FSR) for compact feeds, (2) a low-loss and broadband frequency selective surface (FSS), and (3) a highly accurate and reliable mesh reflector.

  1. Ferrite LTCC based phased array antennas

    KAUST Repository

    Ghaffar, Farhan A.

    2016-11-02

    Two phased array antennas realized in multilayer ferrite LTCC technology are presented in this paper. The use of embedded bias windings in these designs allows the negation of external magnets which are conventionally employed with bulk ferrite medium. This reduces the required magnetostatic field strength by 90% as compared to the traditional designs. The phase shifters are implemented using the SIW technology. One of the designs is operated in the half mode waveguide topology while the other design is based on standard full mode waveguide operation. The two phase shifter designs are integrated with two element patch antenna array and slotted SIW array respectively. The array designs demonstrate a beam steering of 30° and ±19° respectively for a current excitation of 200 mA. The designs, due to their small factor can be easily integrated in modern communication systems which is not possible in the case of bulk ferrite based designs.

  2. Nodding feed antenna for communications with satellites in synchronous orbit

    Science.gov (United States)

    Smetana, J.; Zavesky, R.

    1978-01-01

    The design, fabrication, and performance of a parabolic, ground receiving antenna system with a feed that nods in one axis producing a maximum beam deviation 1.1 deg from boresight is described. The antenna design was: (1)to lower the weight (and the subsequent cost) of the supporting structure and the actuator motors for a tracking antenna by moving just the feed; (2) to use a manual tracking system eliminating the need for expensive electronic controls or computers; (3) to provide for several hours of unattended operation; and (4)to permit operation of the antenna by unskilled personnel. Also described are some physical and orbital phenomenon that effect the operation or design of the antenna. One is the motion of a nearly geostationary satellite due to gravitational forces from the sun, the moon, and other stellar bodies. Others are the rotation of the nodding axis and the feed polarization as a function of the location of the station on the earth. A comparison of per unit cost was made for one unit and a quantity of 100.

  3. Aeronautical satellite antenna steering using magnetic field sensors

    Science.gov (United States)

    Sydor, John; Dufour, Martial

    1993-01-01

    Designers of aeronautical satellite terminals are often faced with the problem of steering a directive antenna from an airplane or helicopter. This problem is usually solved by using aircraft orientation information derived from inertial sensors on-board the aircraft in combination with satellite ephemeris information calculated from geographic coordinates. This procedure works well but relies heavily on avionics that are external to the terminal. For the majority of small aircraft and helicopters which will form the bulk of future aeronautical satcom users, such avionics either do not exist or are difficult for the satellite terminal to interface with. At the Communications Research Center (CRC), work has been undertaken to develop techniques that use the geomagnetic field and satellite antenna pointing vectors (both of which are stationary in a local geographical area) to track the position of a satellite relative to a moving platform such as an aircraft. The performance of this technique is examined and a mathematical steering transformation is developed within this paper. Details are given regarding the experimental program that will be undertaken to test the concepts proposed herein.

  4. Design optimization studies for large-scale contoured beam deployable satellite antennas

    Science.gov (United States)

    Tanaka, Hiroaki

    2006-05-01

    Satellite communications systems over the past two decades have become more sophisticated and evolved new applications that require much higher flux densities. These new requirements to provide high data rate services to very small user terminals have in turn led to the need for large aperture space antenna systems with higher gain. Conventional parabolic reflectors constructed of metal have become, over time, too massive to support these new missions in a cost effective manner and also have posed problems of fitting within the constrained volume of launch vehicles. Designers of new space antenna systems have thus begun to explore new design options. These design options for advanced space communications networks include such alternatives as inflatable antennas using polyimide materials, antennas constructed of piezo-electric materials, phased array antenna systems (especially in the EHF bands) and deployable antenna systems constructed of wire mesh or cabling systems. This article updates studies being conducted in Japan of such deployable space antenna systems [H. Tanaka, M.C. Natori, Shape control of space antennas consisting of cable networks, Acta Astronautica 55 (2004) 519-527]. In particular, this study shows how the design of such large-scale deployable antenna systems can be optimized based on various factors including the frequency bands to be employed with such innovative reflector design. In particular, this study investigates how contoured beam space antennas can be effective by constructed out of so-called cable networks or mesh-like reflectors. This design can be accomplished via "plane wave synthesis" and by the "force density method" and then to iterate the design to achieve the optimum solution. We have concluded that the best design is achieved by plane wave synthesis. Further, we demonstrate that the nodes on the reflector are best determined by a pseudo-inverse calculation of the matrix that can be interpolated so as to achieve the minimum

  5. NASA ACTS Multibeam Antenna (MBA) System. [Advanced Communications Technology Satellite

    Science.gov (United States)

    Choung, Youn H.; Stiles, W. Herschel; Wu, Joseph; Wong, William C.; Chen, C. Harry

    1986-01-01

    The design of the Advanced Communications Technology Satellite MBA system, which provides both spot beam and scanning beam coverage to both high and low burst rates data-users is examined. The MBA consists of receive and transmit antennas installed on a common precision mounting platform that is integrated to the bus through three flexures; a lightweight system with low thermal distortion is obtained by using composite materials for the MBA structures. The RF design, which is a Cassegrain reflector with a large equivalent focal length/aperture size, is described. Consideration is given to the position of the feed in order to minimize scan loss and sidelobe levels, the size of the subreflector in order to minimize feed spillover, and antenna performance degradation caused by reflector surface distortion. Breadbroad model test result reveal that the maximum sidelobe level outside the 2.5 HPBW region is -30 dB or lower relative to the power.

  6. Phase-only nulling for transmit antenna

    Science.gov (United States)

    Hussain, Moayyed A.; Yu, Kai-Bor

    1999-11-01

    This paper describes a technique for transmit antenna nulling for low-cost large sparse phased array radar system. Radar system described includes an array of elemental antennas, each with a transmit/receive (T/R) module. The T/R modules are operated at or near maximum output to achieve maximum CD-to-RF efficiency. A phase controller controls the phase shift, which are imparted by each module to its signal, to form a mainbeam and its associated sidelobes. A perturbation phase generator adds phase shifts computed, to form wide nulls in the sidelobe structure. The nulls are achieved at very minimal loss of gain, in the order of fraction of a dB. The speed of obtaining these nulls in real time allows a rapid steering of these nulls in a hostile environment. The thinned aperture allow designing a light weigh mobile system. In radar context, these nulls may be placed on a source of ground clutter, a set of jammers or a set of undesirable radio sources.

  7. On-glass automotive diversity antenna and LNA design for S-band satellite digital radio

    Science.gov (United States)

    Yeğin, Korkut

    2015-11-01

    Selection combining diversity system with antennas mounted on windshield and backlite of a vehicle is proposed for satellite digital audio radio applications. Standalone exterior mount antennas on metallic vehicles perform well for satellite digital audio radio applications, but for composite body vehicles or interior mount antennas, antenna performance becomes a real issue. Proposed on-glass two-antenna diversity is one solution for such applications. The antenna correlation is calculated using the S-parameters of the antennas and found to be very low due to many wavelengths separation between the antennas. Design of low noise amplifier, which has sub 1 dB noise figure and good P1dB due to strong cellular signals, is also detailed. A diversity receiver is described and ride tests are performed to assess the performance of the diversity system in real-time, under weak satellite signal environment which is regarded as the most challenging reception condition.

  8. Compact, low profile antennas for MSAT and mini-M and Std-M land mobile satellite communications

    Science.gov (United States)

    Strickland, P. C.

    1995-01-01

    CAL Corporation has developed a new class of low profile radiating elements for use in planar phased array antennas. These new elements have been used in the design of a low cost, compact, low profile antenna unit for MSAT and INMARSAT Mini-M land mobile satellite communications. The antenna unit which measures roughly 32 cm in diameter by 5 cm deep incorporates a compact LNA and diplexer unit as well as a complete, low cost, beam steering system. CAL has also developed a low profile antenna unit for INMARSAT-M land mobile satellite communications. A number of these units, which utilize a microstrip patch array design, were put into service in 1994.

  9. Choice of antenna geometry for microwave power transmission from solar power satellites

    Science.gov (United States)

    Potter, Seth D.

    1992-01-01

    A comparison is made between square and circular transmitting antennas for solar power satellite microwave power transmission. It is seen that the exclusion zone around the rectenna needed to protect populations from microwaves is smaller for a circular antenna operating at 2.45 GHz than it is for a square antenna at that frequency. If the frequency is increased, the exclusion zone size remains the same for a square antenna, but becomes even smaller for a circular antenna. Peak beam intensity is the same for both antennas if the frequency and antenna area are equal. The circular antenna puts a somewhat greater amount of power in the main lobe and somewhat less in the side lobes. Since rain attenuation and atmospheric heating remain problems above 10 GHz, it is recommended that future solar power satellite work concentrate on circular transmitting antennas at frequencies of roughly 10 GHz.

  10. A satellite-tracking millimeter-wave reflector antenna system for mobile satellite-tracking

    Science.gov (United States)

    Densmore, Arthur C. (Inventor); Jamnejad, Vahraz (Inventor); Woo, Kenneth E. (Inventor)

    1995-01-01

    A miniature dual-band two-way mobile satellite tracking antenna system mounted on a movable ground vehicle includes a miniature parabolic reflector dish having an elliptical aperture with major and minor elliptical axes aligned horizontally and vertically, respectively, to maximize azimuthal directionality and minimize elevational directionality to an extent corresponding to expected pitch excursions of the movable ground vehicle. A feed-horn has a back end and an open front end facing the reflector dish and has vertical side walls opening out from the back end to the front end at a lesser horn angle and horizontal top and bottom walls opening out from the back end to the front end at a greater horn angle. An RF circuit couples two different signal bands between the feed-horn and the user. An antenna attitude controller maintains an antenna azimuth direction relative to the satellite by rotating it in azimuth in response to sensed yaw motions of the movable ground vehicle so as to compensate for the yaw motions to within a pointing error angle. The controller sinusoidally dithers the antenna through a small azimuth dither angle greater than the pointing error angle while sensing a signal from the satellite received at the reflector dish, and deduces the pointing angle error from dither-induced fluctuations in the received signal.

  11. Satellite-Tracking Millimeter-Wave Reflector Antenna System For Mobile Satellite-Tracking

    Science.gov (United States)

    Densmore, Arthur C. (Inventor); Jamnejad, Vahraz (Inventor); Woo, Kenneth E. (Inventor)

    2001-01-01

    A miniature dual-band two-way mobile satellite-tracking antenna system mounted on a movable vehicle includes a miniature parabolic reflector dish having an elliptical aperture with major and minor elliptical axes aligned horizontally and vertically, respectively, to maximize azimuthal directionality and minimize elevational directionality to an extent corresponding to expected pitch excursions of the movable ground vehicle. A feed-horn has a back end and an open front end facing the reflector dish and has vertical side walls opening out from the back end to the front end at a lesser horn angle and horizontal top and bottom walls opening out from the back end to the front end at a greater horn angle. An RF circuit couples two different signal bands between the feed-horn and the user. An antenna attitude controller maintains an antenna azimuth direction relative to the satellite by rotating it in azimuth in response to sensed yaw motions of the movable ground vehicle so as to compensate for the yaw motions to within a pointing error angle. The controller sinusoidally dithers the antenna through a small azimuth dither angle greater than the pointing error angle while sensing a signal from the satellite received at the reflector dish, and deduces the pointing angle error from dither-induced fluctuations in the received signal.

  12. Low gain and steerable vehicle antennas for communications with land mobile satellite

    Science.gov (United States)

    Woo, K.

    1982-01-01

    Current development activities at JPL for ground mobile vehicle antennas to be used with the Land Mobile Satellite Service (LMSS) system are described. Both low gain and electronically steerable high gain type antennas are discussed in terms of their design concept and RF performance. For the low gain type, three classes of antennas are under various stages of development. These are the crossed-drooping dipole, quadrifilar helix, and microstrip patch designs. The antennas are intended to provide circularly-polarized radiation with a minimum of 3-dB gain in the angular region from 19 degrees to 60 deg from the horizon in elevation plane and with an omnidirectional pattern in azimuthal plane. For the electronically steerable high gain type, circularly-polarized microstrip patch phased arrays formed on a planar surface and on the surface of a truncated cone are under study. The arrays are intended to provide a minimum of 12 dB gain in the same angular region in elevation plane at all azimuthal angles. This coverage is accomplished by scanning the high gain pencil beam in both elevation and azimuthal directions. Both types of antennas are to transmit at 821-831 MHz band and to receive at 866-876 MHz band. They must be of low cost design and reasonably conformal to the vehicle.

  13. Zenith Pass Problem of Inter-satellite Linkage Antenna Based on Program Guidance Method

    Institute of Scientific and Technical Information of China (English)

    Zhai Kun; Yang Di

    2008-01-01

    While adopting an elevation-over-azimuth architecture by an inter-satellite linkage antenna of a user satellite, a zenith pass problem always occurs when the antenna is tracing the tracking and data relay satellite (TDRS). This paper deals with this problem by way of,firstly, introducing movement laws of the inter-satellite linkage to predict the movement of the user satellite antenna followed by analyzing the potential pass moment and the actual one of the zenith pass in detail. A number of specific orbit altitudes for the user satellite that can remove the blindness zone are obtained. Finally, on the base of the predicted results from the movement laws of the inter-satellite linkage, the zenith pass tracing strategies for the user satellite antenna are designed under the program guidance using a trajectory preprocessor. Simulations have confirmed the reasonability and feasibility of the strategies in dealing with the zenith pass problem.

  14. Simulation of a ring resonator-based optical beamformer system for phased array receive antennas

    NARCIS (Netherlands)

    Tijmes, M.R.; Meijerink, Arjan; Roeloffzen, C.G.H.; Bentum, Marinus Jan

    2009-01-01

    A new simulator tool is described that can be used in the field of RF photonics. It has been developed on the basis of a broadband, continuously tunable optical beamformer system for phased array receive antennas. The application that is considered in this paper is airborne satellite reception of di

  15. Design of a ring resonator-based optical beam forming network for phased array receive antennas

    NARCIS (Netherlands)

    Klooster, van 't J.W.; Roeloffzen, C.G.H.; Meijerink, A.; Zhuang, L.; Marpaung, D.A.I.; Etten, van W.C.; Heideman, R.G.; Leinse, A.; Schippers, H.; Verpoorte, J.; Wintels, M.

    2008-01-01

    A novel squint-free ring resonator-based optical beam forming network (OBFN) for phased array antennas (PAA) is proposed. It is intended to provide broadband connectivity to airborne platforms via geostationary satellites. In this paper, we present the design of the OBFN and its control system. Our

  16. Development of a broadband integrated optical beamformer for Ku-Band Phased Array Antennas

    NARCIS (Netherlands)

    Roeloffzen, C.G.H.; van Dijk, Paul; Marpaung, D.A.I.; Burla, M.; Zhuang, L.

    2012-01-01

    Currently an integrated photonic beamformer for electronically-steered Ku-band phased array antenna (PAA) systems for satellite communications is being developed, targeting continuous reception of the full DVB-S band (10.7- 12.75 GHz), squint-free and seamless beam steering, and polarization

  17. Simulation of a ring-resonator based optical beamformer system for phased array receive antennas

    NARCIS (Netherlands)

    Tijmes, M.R.; Meijerink, A.; Bentum, M.J.; Roeloffzen, C.G.H.

    2009-01-01

    A new simulator tool is described that can be used in the field of RF photonics. It has been developed on the basis of a broadband, continuously tunable optical beamformer system for phased array receive antennas. The application that is considered in this paper is airborne satellite reception of di

  18. Robust FDI for A Ship-mounted Satellite Tracking Antenna: A Nonlinear Approach

    DEFF Research Database (Denmark)

    Soltani, Mohsen; Izadi-Zamanabadi, Roozbeh; Wisniewski, Rafal

    2008-01-01

    Overseas telecommunication is preserved by means of satellite communication. Tracking system postures the on-board antenna toward a chosen satellite while the external disturbances affect the antenna. Certain faults (beam sensor malfunction or signal blocking) cause interruption in the communicat......Overseas telecommunication is preserved by means of satellite communication. Tracking system postures the on-board antenna toward a chosen satellite while the external disturbances affect the antenna. Certain faults (beam sensor malfunction or signal blocking) cause interruption...... in the communication connection resulting in the loss of the tracking functionality. In this paper, an optimization based fault diagnosis system is proposed for the nonlinear model of the satellite tracking antenna (STA). The suggested method is able to estimate the fault for a class of nonlinear systems acting under...

  19. Modified Vivaldi antenna with improved gain and phase center stability

    DEFF Research Database (Denmark)

    Zhang, Shuai

    2016-01-01

    A modified Vivaldi antenna is proposed with improved gain and phase centre stability. By applying a high permittivity dielectric substrate, the realized gain is enlarged while maintaining the compactness of the designed antenna. With a redistributed comb-shape corrugation the phase centre stabili...... of the antenna is significantly improved. The designed modified Vivaldi antenna covers the lower UWB band of 3.1-5 GHz with a realized gain higher than 10 dBi. A stable phase centre and radiation patterns over the operating band are realized....

  20. Conversion of a 30-m former satellite communications antenna to a radio telescope

    Science.gov (United States)

    Deboer, David R.; Steffes, Paul G.; Glowacki, John M.

    1998-05-01

    A class of large satellite communication antennas built in the mid-1970's comprise a potential set of large antennas available for use by radio astronomers upon upgrade. With the advent of low noise technology these facilities have been superseded in the communications industry by smaller, more manageable facilities. Although many have sat idle and decaying over the intervening years, these facilities remain a potential resource for research and education. A pair of such dishes has been acquired by Georgia Tech and one of the 30 meter antennas has been completely mechanically and electrically stripped and new mechanical, control, RF, and electrical systems installed. The antenna is now driven by four continuous-speed vector-controlled three-phase AC induction motors with variable frequency vector motor drives. Sixteen bit resolution optical absolute position encoders on each axis provide telescope pointing data. Sixteen bit resolution optical absolute position encoders on each axis provide telescope pointing data. A programmable logic controller provides interlock monitoring and control. The antenna is controllable both manually via a portable remote control unit and via a Pentium PC running control software on a real-time UNIX-based platform. The manual unit allows limited control at two user-selectable speeds while computer control allows full tracking capability with accuracies of better than 0.3 arcminutes. The facility can be remotely controlled via the internet, although currently only a dedicated line is used. The antenna has been refitted with an ultra-broadband feed system capable of operating from 1-7 GHz.

  1. Design and Optimization of a Compact Wideband Hat-Fed Reflector Antenna for Satellite Communications

    Science.gov (United States)

    Geterud, Erik G.; Yang, Jian; Ostling, Tomas; Bergmark, Pontus

    2013-01-01

    We present a new design of the hat-fed reflector antenna for satellite communications, where a low reflection coefficient, high gain, low sidelobes and low cross-polar level are required over a wide frequency band. The hat feed has been optimized by using the Genetic Algorithm through a commercial FDTD solver, QuickWave-V2D, together with an own developed optimization code. The Gaussian vertex plate has been applied at the center of the reflector in order to improve the reflection coefficient and reduce the far-out sidelobes. A parabolic reflector with a ring-shaped focus has been designed for obtaining nearly 100% phase efficiency. The antenna's reflection coefficient is below -17 dB and the radiation patterns satisfy the M-x standard co- and cross-polar sidelobe envelopes for satellite ground stations over a bandwidth of 30%. A low-cost monolayer radome has been designed for the antenna with satisfactory performance. The simulations have been verified by measurements; both of them are presented in the paper.

  2. A simple ship-borne antenna stabilizer for limited area maritime satellite communication systems

    Science.gov (United States)

    Satoh, K.; Nakamae, M.; Mishima, H.

    1984-10-01

    This paper deals with a simple ship-borne antenna stabilizer for use in limited area multi-beam maritime satellite communication systems. A limited area system with high satellite e.i.r.p. is expected to be a more economical satellite system than a global system, because a low-gain ship-borne antenna and a simplified antenna stabilizer can be used. An optimum configuration is proposed for small size and low cost pendulum-type antenna stabilizers which are suitable for low gain ship-borne antennas. Also, a performance evaluation of the stabilizers is discussed using a statistical analysis of ship motion characteristics. Furthermore, fading characteristics of received signal strength due to antenna off-beam fluctuation and sea surface random reflection are experimentally evaluated.

  3. Optical phased arrays with evanescently-coupled antennas

    Science.gov (United States)

    Sun, Jie; Watts, Michael R; Yaacobi, Ami; Timurdogan, Erman

    2015-03-24

    An optical phased array formed of a large number of nanophotonic antenna elements can be used to project complex images into the far field. These nanophotonic phased arrays, including the nanophotonic antenna elements and waveguides, can be formed on a single chip of silicon using complementary metal-oxide-semiconductor (CMOS) processes. Directional couplers evanescently couple light from the waveguides to the nanophotonic antenna elements, which emit the light as beams with phases and amplitudes selected so that the emitted beams interfere in the far field to produce the desired pattern. In some cases, each antenna in the phased array may be optically coupled to a corresponding variable delay line, such as a thermo-optically tuned waveguide or a liquid-filled cell, which can be used to vary the phase of the antenna's output (and the resulting far-field interference pattern).

  4. Bit Error Rate Due to Misalignment of Earth Station Antenna Pointing to Satellite

    Directory of Open Access Journals (Sweden)

    Wahyu Pamungkas

    2010-04-01

    Full Text Available One problem causing reduction of energy in satellite communications system is the misalignment of earth station antenna pointing to satellite. Error in pointing would affect the quality of information signal to energy bit in earth station. In this research, error in pointing angle occurred only at receiver (Rx antenna, while the transmitter (Tx antennas precisely point to satellite. The research was conducted towards two satellites, namely TELKOM-1 and TELKOM-2. At first, measurement was made by directing Tx antenna precisely to satellite, resulting in an antenna pattern shown by spectrum analyzer. The output from spectrum analyzers is drawn with the right scale to describe swift of azimuth and elevation pointing angle towards satellite. Due to drifting from the precise pointing, it influenced the received link budget indicated by pattern antenna. This antenna pattern shows reduction of power level received as a result of pointing misalignment. As a conclusion, the increasing misalignment of pointing to satellite would affect in the reduction of received signal parameters link budget of down-link traffic.

  5. Adaptive array antenna for satellite cellular and direct broadcast communications

    Science.gov (United States)

    Horton, Charles R.; Abend, Kenneth

    1993-01-01

    Adaptive phased-array antennas provide cost-effective implementation of large, light weight apertures with high directivity and precise beamshape control. Adaptive self-calibration allows for relaxation of all mechanical tolerances across the aperture and electrical component tolerances, providing high performance with a low-cost, lightweight array, even in the presence of large physical distortions. Beam-shape is programmable and adaptable to changes in technical and operational requirements. Adaptive digital beam-forming eliminates uplink contention by allowing a single electronically steerable antenna to service a large number of receivers with beams which adaptively focus on one source while eliminating interference from others. A large, adaptively calibrated and fully programmable aperture can also provide precise beam shape control for power-efficient direct broadcast from space. Advanced adaptive digital beamforming technologies are described for: (1) electronic compensation of aperture distortion, (2) multiple receiver adaptive space-time processing, and (3) downlink beam-shape control. Cost considerations for space-based array applications are also discussed.

  6. Downsizing Antenna Technologies for Mobile and Satellite Communications

    Science.gov (United States)

    Huang, J.; Densmore, A.; Tulintseff, A.; Jamnejad, V.

    1993-01-01

    Due to the increasing and stringent functional requirements (larger capacity, longer distances, etc.) of modern day communication systems, higher antenna gains are generally needed. This higher gain implies larger antenna size and mass which are undesirable to many systems. Consequently, downsizing antenna technology becomes one of the most critical areas for research and development efforts. Techniques to reduce antenna size can be categorized and are briefly discussed.

  7. Steerable K/Ka-Band Antenna For Land-Mobile Satellite Applications

    Science.gov (United States)

    Densmore, Arthur; Jamnejad, Vahraz; Woo, Kenneth

    1994-01-01

    Prototype steerable microwave antenna tracks and communicates with geostationary satellite. Designed to mount on roof of vehicle and only 10 cm tall. K/Ka-band antenna rugged and compact to suit rooftop mobile operating environment. More-delicate signal-processing and control equipment located inside vehicle.

  8. Support scattering effects on low-gain satellite antenna pattern measurements

    DEFF Research Database (Denmark)

    Appel-Hansen, Jørgen

    1973-01-01

    The purpose of the present investigation is to determine the difference between the scattering effects from two types of supports on satellite antenna pattern measurements. The difference in scattering effects is estimated by comparing low-gain antenna patterns recorded when using a foam tower an...

  9. Application of MMIC modules in future multiple beam satellite antenna systems

    Science.gov (United States)

    Smetana, J.

    1982-01-01

    Multiple beam antenna systems for advanced communication satellites operating in the 30/20 GHz frequency bands (30 GHz uplink, 20 GHz downlink) were developed. Up to twenty 0.3 deg HPBW fixed spot beams and six 0.3 deg HPBW scanning spot beams will be required. Array-fed dual reflector antenna systems in which monolithic microwave integrated circuit (MMIC) phase shift and amplifier modules are used with each radiating element of the feed array for beam pointing and power gain were developed. The feasibility of distributed power amplification and beam pointing with MMIC modules in the elements of an array and to develop a data base for future development were demonstrated. The technical discussion centers around the potential advantages of ""monolithic'' antennas for specific applications as compared to systems using high powered TWT's. These include: reduced losses in the beam forming network; advantage of space combining and graceful degradation; dynamic control of beam pointing and illumination contour; and possibilities for cost and weight reduction.

  10. 30/20 GHz communications satellite multibeam antenna

    Science.gov (United States)

    Scott, W. G.; Luh, H. S.; Smoll, A. E.; Matthews, E. W.

    1982-01-01

    A 20 GHz downlink satellite antenna design is described. The aperture simultaneously radiates 18 fixed, 0.3 deg width pencil beams directed at 18 cities distributed over CONUS for Trunking Service. All beams use the same trunk frequency allocation for 18 reuses of the band. The same aperture also radiates six additional 0.3 deg spot beams for Customer Premises Service (CPS) for TDMA beam hopping operation to small terminals anywhere in CONUS. Each CPS beam scans one sector of CONUS and all six beams are frequency reused in a CPS band. Offset dual reflector optics are used with a feed array and multiport beam forming network (BFN). For so many frequency reuses, sidelobes per beam must be 30 to 40 dB down over CONUS. Novel dual reflector optics were devised with shaped surfaces providing low aberrations for all beam positions over CONUS (+ or - 12 BW by + or - 5 BW). Scan loss under 1 dB is calculated with nearly constant sidelobes. For each beam position, a 7-element cluster of feeds is activated in the feed array with coefficients adjusted by the BFN to maintain low sidelobes and thus high beam isolation for frequency reuse.

  11. Phase Retrieval for Radio Telescope and Antenna Control

    Science.gov (United States)

    Dean, Bruce

    2011-01-01

    Phase-retrieval is a general term used in optics to describe the estimation of optical imperfections or "aberrations." The purpose of this innovation is to develop the application of phase retrieval to radio telescope and antenna control in the millimeter wave band. Earlier techniques do not approximate the incoherent subtraction process as a coherent propagation. This approximation reduces the noise in the data and allows a straightforward application of conventional phase retrieval techniques for radio telescope and antenna control. The application of iterative-transform phase retrieval to radio telescope and antenna control is made by approximating the incoherent subtraction process as a coherent propagation. Thus, for systems utilizing both positive and negative polarity feeds, this approximation allows both surface and alignment errors to be assessed without the use of additional hardware or laser metrology. Knowledge of the antenna surface profile allows errors to be corrected at a given surface temperature and observing angle. In addition to imperfections of the antenna surface figure, the misalignment of multiple antennas operating in unison can reduce or degrade the signal-to-noise ratio of the received or broadcast signals. This technique also has application to the alignment of antenna array configurations.

  12. UHF coplanar-slot antenna for aircraft-to-satellite data communications

    Science.gov (United States)

    Myhre, R. W.

    1979-01-01

    The initiative for starting the Aircraft-to-Satellite Data Relay (ASDAR) Program came from a recognition that much of the world's weather originates in the data sparse area of the tropics which are primarily ocean. The ASDAR system consists of (1) a data acquisition and control unit to acquire, store and format these data; (2) a clock to time the data sampling and transmission periods; and (3) a transmitter and low-profile upper hemisphere coverage antenna to relay the formatted data via satellite to the National Weather Service ground stations, as shown schematically. The low-profile antenna is a conformal antenna based on the coplanar-slot approach. The antenna is circular polarized and has an on-axis gain of nearly 2.5 dB and a HPBW greater than 90 deg. The discussion covers antenna design, radiation characteristics, flight testing, and system performance.

  13. Effects on dynamic characters of antenna structures in satellite induced by disordered parameters

    Institute of Scientific and Technical Information of China (English)

    Liu Xiangqiu; Wang Cong; Wang Weiyuan; Zou Zhenzhu

    2009-01-01

    A simplified dynamic model of a dish antenna in satellite is established in this article. The model can be easily used to analyze the dynamic behaviour of the antenna structure. In terms of the simplified model, effects on dynamic characters due to the disorder of parameters are investigated in details. The frequencies calculated by the simplified model accord with those computed by ANSYS. Based on the mode shapes of disordered and perfect structure, the influence law and varying trend of dynamic characters of antenna structures in satellites produced by stiffness and mass of antenna ribs, stiffness of antenna membranes and angles between adjacent ribs, are obtained. The analyses in the paper indicate that the effects by disordered parameters can not be ignored in the dynamic analysis of such structures.

  14. Visibility conflict resolution for multiple antennae and multi-satellites via genetic algorithm

    Science.gov (United States)

    Lee, Junghyun; Hyun, Chung; Ahn, Hyosung; Wang, Semyung; Choi, Sujin; Jung, Okchul; Chung, Daewon; Ko, Kwanghee

    Satellite mission control systems typically are operated by scheduling missions to the visibility between ground stations and satellites. The communication for the mission is achieved by interacting with satellite visibility and ground station support. Specifically, the satellite forms a cone-type visibility passing over a ground station, and the antennas of ground stations support the satellite. When two or more satellites pass by at the same time or consecutively, the satellites may generate a visibility conflict. As the number of satellites increases, solving visibility conflict becomes important issue. In this study, we propose a visibility conflict resolution algorithm of multi-satellites by using a genetic algorithm (GA). The problem is converted to scheduling optimization modeling. The visibility of satellites and the supports of antennas are considered as tasks and resources individually. The visibility of satellites is allocated to the total support time of antennas as much as possible for users to obtain the maximum benefit. We focus on a genetic algorithm approach because the problem is complex and not defined explicitly. The genetic algorithm can be applied to such a complex model since it only needs an objective function and can approach a global optimum. However, the mathematical proof of global optimality for the genetic algorithm is very challenging. Therefore, we apply a greedy algorithm and show that our genetic approach is reasonable by comparing with the performance of greedy algorithm application.

  15. Narrow multibeam satellite ground station antenna employing a linear array with a geosynchronous arc coverage of 60 deg. I - Theory

    Science.gov (United States)

    Amitay, N.; Gans, M. J.

    1982-11-01

    The feasibility of using an appropriately squinted linear scan in narrow multibeam satellite ground station antennas employing phased arrays is demonstrated. This linear scan has the potential of reducing the complexity of a narrow-beam planar array to that of a linear array. Calculations for such antennas placed at cities throughout the U.S. show that the peak beam pointing error in covering the 70 deg W to 130 deg W geosynchronous equatorial arc (GEA) is under 5/1000th of a degree. Communication at a 300 MBd rate in the 12/14 GHz band can be made feasible, for a grating lobe-free scan and 0.5 deg beamwidth antenna, by using a relatively simple time equalization.

  16. Cube/Small Satellite Antenna Design and Performance Optimization Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This IRAD proposal investigates and proposes different small, efficient, low cost, reliable, and robust antenna design concepts with stable electrical and radiation...

  17. Compact and broadband circularly polarized ring antenna with wide beam-width for multiple global navigation satellite systems

    Institute of Scientific and Technical Information of China (English)

    Zhang Hong-Lin; Hu Bin-Jie; Zhang Xiu-Yin

    2012-01-01

    A compact and broadband circularly polarized (CP) annular ring antenna with wide beam-width is proposed for multiple global navigation satellite systems (GNSS) in the L1 band.The annular ring is excited by two modified L-probes with quadrature phase difference.It has a 36.3% 10-dB return loss bandwidth and a 13% 3-dB axial ratio bandwidth,because of the orthogonal L-probes with 90° phase difference.The measured peak gain of the antenna is 3.9 dBic.It can detect the satellites at lower elevation as its half power beam-width (HPBW) is 113° in both the x-z and y-z planes,achieving a cross-polarization level of larger than 25 dB.Noticeably,the antenna achieves 89% size reduction compared with the conventional half wavelength patch antennas.It can be used in hand-held navigation devices of multiple GNSS such as COMPASS,Galileo,GPS and GLONASS.

  18. PHASIM, an advanced phased array antenna software simulator

    NARCIS (Netherlands)

    Keizer, W.P.M.N.

    2000-01-01

    A sophisticated phased array simulator software package for the design and analysis of planar phased array antennas is presented. This package can accurately simulate the far-field characteristics of a large variety of planar phased array configurations in both the frequency and time domain. The sim

  19. An L-strip fed stacked patch antenna for maritime satellite communications

    Institute of Scientific and Technical Information of China (English)

    FU Shi-qiang; FANG Shao-jun

    2008-01-01

    A practical antenna has been designed and developed for INMARSAT mobile satellite communications. The design uses low cost materials such as foam and copper foil to create a stacked microstrip antenna array. Several techniques were adopted to enhance the impedance bandwidth and axial ratio bandwidth. The final design parameters were optimized by EM simulation. Finally, the L-strip fed six-element stacked microstrip antenna array was constructed and tested. Simulated and measured results show that in the whole INMARSAT work band, the VSWR of the antenna is less than 1.6, its antenna gain is higher than 15riB and wide-angle axial ratio (AR) 3dB is more than 21°. The antenna has been successfully used with a HNS 9201 terminal.

  20. Dynamic Modeling and Simulation of Marine Satellite Tracking Antenna Using Lagrange Method

    DEFF Research Database (Denmark)

    Wang, Yunlong; Nourbakhsh, S. M; Hussain, Dil muhammed Akbar

    2016-01-01

    Marine Satellite Tracking Antenna (MSTA) is a necessary device in ships for receiving satellite signals when they are sailing on the sea. This paper presents a simple methodology to obtain the dynamic equations of MSTA through Lagrange method, which is fundamental in design of modelbased...

  1. Analysis of electrical performances of planar active phased array antennas with distorted array plane

    Institute of Scientific and Technical Information of China (English)

    Wang Congsi; Bao Hong; Zhang Fushun; Feng Xingang

    2009-01-01

    a planar phased array antenna with different distortions grades prove the validity of the model.Therefore,by the method,the antenna designers may set the reasonable requirement on the structural tolerance in manufacturing antenna.

  2. Large-Aperture Membrane Active Phased-Array Antennas

    Science.gov (United States)

    Karasik, Boris; McGrath, William; Leduc, Henry

    2009-01-01

    Large-aperture phased-array microwave antennas supported by membranes are being developed for use in spaceborne interferometric synthetic aperture radar systems. There may also be terrestrial uses for such antennas supported on stationary membranes, large balloons, and blimps. These antennas are expected to have areal mass densities of about 2 kg/sq m, satisfying a need for lightweight alternatives to conventional rigid phased-array antennas, which have typical areal mass densities between 8 and 15 kg/sq m. The differences in areal mass densities translate to substantial differences in total mass in contemplated applications involving aperture areas as large as 400 sq m. A membrane phased-array antenna includes patch antenna elements in a repeating pattern. All previously reported membrane antennas were passive antennas; this is the first active membrane antenna that includes transmitting/receiving (T/R) electronic circuits as integral parts. Other integral parts of the antenna include a network of radio-frequency (RF) feed lines (more specifically, a corporate feed network) and of bias and control lines, all in the form of flexible copper strip conductors on flexible polymeric membranes. Each unit cell of a prototype antenna (see Figure 1) contains a patch antenna element and a compact T/R module that is compatible with flexible membrane circuitry. There are two membrane layers separated by a 12.7-mm air gap. Each membrane layer is made from a commercially available flexible circuit material that, as supplied, comprises a 127-micron-thick polyimide dielectric layer clad on both sides with 17.5-micron-thick copper layers. The copper layers are patterned into RF, bias, and control conductors. The T/R module is located on the back side of the ground plane and is RF-coupled to the patch element via a slot. The T/R module is a hybrid multilayer module assembled and packaged independently and attached to the membrane array. At the time of reporting the information for

  3. Estimating Transmitted-Signal Phase Variations for Uplink Array Antennas

    Science.gov (United States)

    Paal, Leslie; Mukai, Ryan; Vilntrotter, Victor; Cornish, Timothy; Lee, Dennis

    2009-01-01

    A method of estimating phase drifts of microwave signals distributed to, and transmitted by, antennas in an array involves the use of the signals themselves as phase references. The method was conceived as part of the solution of the problem of maintaining precise phase calibration required for proper operation of an array of Deep Space Network (DSN) antennas on Earth used for communicating with distant spacecraft at frequencies between 7 and 8 GHz. The method could also be applied to purely terrestrial phased-array radar and other radio antenna array systems. In the DSN application, the electrical lengths (effective signal-propagation path lengths) of the various branches of the system for distributing the transmitted signals to the antennas are not precisely known, and they vary with time. The variations are attributable mostly to thermal expansion and contraction of fiber-optic and electrical signal cables and to a variety of causes associated with aging of signal-handling components. The variations are large enough to introduce large phase drifts at the signal frequency. It is necessary to measure and correct for these phase drifts in order to maintain phase calibration of the antennas. A prior method of measuring phase drifts involves the use of reference-frequency signals separate from the transmitted signals. A major impediment to accurate measurement of phase drifts over time by the prior method is the fact that although DSN reference-frequency sources separate from the transmitting signal sources are stable and accurate enough for most DSN purposes, they are not stable enough for use in maintaining phase calibrations, as required, to within a few degrees over times as long as days or possibly even weeks. By eliminating reliance on the reference-frequency subsystem, the present method overcomes this impediment. In a DSN array to which the present method applies (see figure), the microwave signals to be transmitted are generated by exciters in a signal

  4. Conformal phased array with beam forming for airborne satellite communication

    NARCIS (Netherlands)

    Schippers, H.; Verpoorte, J.; Jorna, P.; Hulzinga, A.; Meijerink, A.; Roeloffzen, C.G.H.; Heideman, R.G.; Leinse, A.; Wintels, M.

    2008-01-01

    For enhanced communication on board of aircraft novel antenna systems with broadband satellite-based capabilities are required. The installation of such systems on board of aircraft requires the development of a very low-profile aircraft antenna, which can point to satellites anywhere in the upper h

  5. Autonomous Pointing Control of a Large Satellite Antenna Subject to Parametric Uncertainty.

    Science.gov (United States)

    Wu, Shunan; Liu, Yufei; Radice, Gianmarco; Tan, Shujun

    2017-03-10

    With the development of satellite mobile communications, large antennas are now widely used. The precise pointing of the antenna's optical axis is essential for many space missions. This paper addresses the challenging problem of high-precision autonomous pointing control of a large satellite antenna. The pointing dynamics are firstly proposed. The proportional-derivative feedback and structural filter to perform pointing maneuvers and suppress antenna vibrations are then presented. An adaptive controller to estimate actual system frequencies in the presence of modal parameters uncertainty is proposed. In order to reduce periodic errors, the modified controllers, which include the proposed adaptive controller and an active disturbance rejection filter, are then developed. The system stability and robustness are analyzed and discussed in the frequency domain. Numerical results are finally provided, and the results have demonstrated that the proposed controllers have good autonomy and robustness.

  6. A phased array antenna with a broadly steerable beam based on a low-loss metasurface lens

    Science.gov (United States)

    Liu, Yahong; Jin, Xueyu; Zhou, Xin; Luo, Yang; Song, Kun; Huang, Lvhongzi; Zhao, Xiaopeng

    2016-10-01

    A new concept for a gradient phase discontinuity metasurface lens integrated with a phased array antenna possessing a broadly steerable beam is presented in this paper. The metasurface lens is composed of a metallic H-shaped pattern and the metallic square split ring can achieve complete 360° transmission phase coverage at 30° phase intervals. The metasurface can refract an incident plane wave to an angle at will by varying the lattice constant. We demonstrate that the beam steering range of the phased array antenna is between 12° and 85° when the metasurface lens with a refracting electromagnetic wave is employed at 45°. Interestingly, the proposed array antenna has a much higher gain than a conventional phased array antenna at low elevation angles. It is expected that the proposed array antenna will have potential applications in wireless and satellite communications. Furthermore, the proposed array antenna is fabricated easily and is also low in cost due to its microstrip technology.

  7. Cylindrical Antenna With Partly Adaptive Phased-Array Feed

    Science.gov (United States)

    Hussein, Ziad; Hilland, Jeff

    2003-01-01

    A proposed design for a phased-array fed cylindrical-reflector microwave antenna would enable enhancement of the radiation pattern through partially adaptive amplitude and phase control of its edge radiating feed elements. Antennas based on this design concept would be attractive for use in radar (especially synthetic-aperture radar) and other systems that could exploit electronic directional scanning and in which there are requirements for specially shaped radiation patterns, including ones with low side lobes. One notable advantage of this design concept is that the transmitter/ receiver modules feeding all the elements except the edge ones could be identical and, as a result, the antenna would cost less than in the cases of prior design concepts in which these elements may not be identical.

  8. Microstrip Phased Array Antennas Printed on Inclined Planes

    Directory of Open Access Journals (Sweden)

    A. Papiernik

    1996-06-01

    Full Text Available This paper presents an analysis of the electromagnetic field radiated by micro-strip patch antennas printed on inclined surfaces. The theoretical approach allows to apply spatial rotations to each source. The computer simulation developed permits us to experiment different antenna structures and two original realisations are proposed: a 2-element array printed on two inclined planes and a 4-element array laid out on a pyramidal surface. In addition, it enables the choice of the phase applied to each radiator to produce a beam deflection function. A good accuracy is obtained between theoretical and experimental results. The aim of this study is to optimise the parameters of such antennas to achieve the desired radiation patterns, from printed phased arrays on conformal surfaces. We also present the theoretical behaviour of a octagonal pyramid.

  9. A Ferrite LTCC-Based Monolithic SIW Phased Antenna Array

    KAUST Repository

    Nafe, Ahmed

    2016-11-17

    In this work, we present a novel configuration for realizing monolithic SIW-based phased antenna arrays using Ferrite LTCC technology. Unlike the current common schemes for realizing SIW phased arrays that rely on surface-mount component (p-i-n diodes, etc) for controlling the phase of the individual antenna elements, here the phase is tuned by biasing of the ferrite filling of the SIW. This approach eliminates the need for mounting of any additional RF components and enables seamless monolithic integration of phase shifters and antennas in SIW technology. As a proof of concept, a two-element slotted SIW-based phased array is designed, fabricated and measured. The prototype exhibits a gain of 4.9 dBi at 13.2 GHz and a maximum E-plane beam-scanning of 28 degrees using external windings for biasing the phase shifters. Moreover, the array can achieve a maximum beam-scanning of 19 degrees when biased with small windings that are embedded in the package. This demonstration marks the first time a fully monolithic SIW-based phased array is realized in Ferrite LTCC technology and paves the way for future larger-size implementations.

  10. Development of the sandra antenna for airborne satellite communication

    NARCIS (Netherlands)

    Verpoorte, J.; Schippers, H.; Jorna, P.; Hulzinga, A.; Roeloffzen, C.G.H.; Marpaung, D.A.I.; Sanadgol, B.; Baggen, R.; Wang, Qin; Noharet, B.; Beeker, W.; Leinse, A.; Heideman, R.G.

    2011-01-01

    Novel avionics communication systems are required for increasing flight safety and operational integrity, for optimizing economy of operations and for enhancing passenger services. One of the key technologies to be developed is an antenna system that will provide broadband connectivity within aircra

  11. Improving microwave antenna gain and bandwidth with phase compensation metasurface

    Directory of Open Access Journals (Sweden)

    Ke Chen

    2015-06-01

    Full Text Available Metasurface, as a planar version of artificial metamaterial, provide an effective way to manipulate electromagnetic wave propagation. Here, we present a transparent metasurface for compensating the out-of-phase radiation from a microstrip patch antenna to improve its radiation gain and bandwidth. Based on the equivalence principle of Huygens’ surface, we propose metasurface composed of both inductive and capacitive resonant elements which could produce high transmission with variable phase characteristics. Such metasurface mounted on a patch antenna can transform the spherical-like phase profile generated from the patch into an in-phase planar one. A prototype antenna has been fabricated and validated the squeezed radiation pattern with suppressed sidelobes as well as enhanced impedance bandwidth due to strong near-field coupling. As operating at around 5.7 GHz, the proposed antenna may have potential application in wireless communication systems especially for point-to-point data transmission. It is believed that the design methodology could also be scaled to other frequency bands such as millimeter or terahertz wave.

  12. Improving microwave antenna gain and bandwidth with phase compensation metasurface

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Ke; Yang, Zhongjie; Feng, Yijun, E-mail: yjfeng@nju.edu.cn; Zhu, Bo; Zhao, Junming; Jiang, Tian [Department of Electronic Engineering, School of Electronic Science and Engineering, Nanjing University, Nanjing, 210093 (China)

    2015-06-15

    Metasurface, as a planar version of artificial metamaterial, provide an effective way to manipulate electromagnetic wave propagation. Here, we present a transparent metasurface for compensating the out-of-phase radiation from a microstrip patch antenna to improve its radiation gain and bandwidth. Based on the equivalence principle of Huygens’ surface, we propose metasurface composed of both inductive and capacitive resonant elements which could produce high transmission with variable phase characteristics. Such metasurface mounted on a patch antenna can transform the spherical-like phase profile generated from the patch into an in-phase planar one. A prototype antenna has been fabricated and validated the squeezed radiation pattern with suppressed sidelobes as well as enhanced impedance bandwidth due to strong near-field coupling. As operating at around 5.7 GHz, the proposed antenna may have potential application in wireless communication systems especially for point-to-point data transmission. It is believed that the design methodology could also be scaled to other frequency bands such as millimeter or terahertz wave.

  13. Improving microwave antenna gain and bandwidth with phase compensation metasurface

    Science.gov (United States)

    Chen, Ke; Yang, Zhongjie; Feng, Yijun; Zhu, Bo; Zhao, Junming; Jiang, Tian

    2015-06-01

    Metasurface, as a planar version of artificial metamaterial, provide an effective way to manipulate electromagnetic wave propagation. Here, we present a transparent metasurface for compensating the out-of-phase radiation from a microstrip patch antenna to improve its radiation gain and bandwidth. Based on the equivalence principle of Huygens' surface, we propose metasurface composed of both inductive and capacitive resonant elements which could produce high transmission with variable phase characteristics. Such metasurface mounted on a patch antenna can transform the spherical-like phase profile generated from the patch into an in-phase planar one. A prototype antenna has been fabricated and validated the squeezed radiation pattern with suppressed sidelobes as well as enhanced impedance bandwidth due to strong near-field coupling. As operating at around 5.7 GHz, the proposed antenna may have potential application in wireless communication systems especially for point-to-point data transmission. It is believed that the design methodology could also be scaled to other frequency bands such as millimeter or terahertz wave.

  14. A new approach to design of quasi-isotropic antenna systems for satellite applications

    DEFF Research Database (Denmark)

    Schjær-Jacobsen, Hans; Hansen, J.E.

    1976-01-01

    The new approach considered takes into account the maximum error of the quasi-isotropic radiation pattern relative to the ideal pattern. A design example involving a spherical satellite with quarter wave monopoles is used to demonstrate the effectiveness of the new approach. An investigation...... is conducted concerning the minimax optimization of power radiation patterns. It is shown that the minimax objective represents a useful alternative to the isotropy concept in the design of quasi-isotropic antenna systems for satellite applications....

  15. A new approach to design of quasi-isotropic antenna systems for satellite applications

    DEFF Research Database (Denmark)

    Schjær-Jacobsen, Hans; Hansen, J.E.

    1976-01-01

    The new approach considered takes into account the maximum error of the quasi-isotropic radiation pattern relative to the ideal pattern. A design example involving a spherical satellite with quarter wave monopoles is used to demonstrate the effectiveness of the new approach. An investigation...... is conducted concerning the minimax optimization of power radiation patterns. It is shown that the minimax objective represents a useful alternative to the isotropy concept in the design of quasi-isotropic antenna systems for satellite applications....

  16. Autonomous Pointing Control of a Large Satellite Antenna Subject to Parametric Uncertainty

    Science.gov (United States)

    Wu, Shunan; Liu, Yufei; Radice, Gianmarco; Tan, Shujun

    2017-01-01

    With the development of satellite mobile communications, large antennas are now widely used. The precise pointing of the antenna’s optical axis is essential for many space missions. This paper addresses the challenging problem of high-precision autonomous pointing control of a large satellite antenna. The pointing dynamics are firstly proposed. The proportional–derivative feedback and structural filter to perform pointing maneuvers and suppress antenna vibrations are then presented. An adaptive controller to estimate actual system frequencies in the presence of modal parameters uncertainty is proposed. In order to reduce periodic errors, the modified controllers, which include the proposed adaptive controller and an active disturbance rejection filter, are then developed. The system stability and robustness are analyzed and discussed in the frequency domain. Numerical results are finally provided, and the results have demonstrated that the proposed controllers have good autonomy and robustness. PMID:28287450

  17. Autonomous Pointing Control of a Large Satellite Antenna Subject to Parametric Uncertainty

    Directory of Open Access Journals (Sweden)

    Shunan Wu

    2017-03-01

    Full Text Available With the development of satellite mobile communications, large antennas are now widely used. The precise pointing of the antenna’s optical axis is essential for many space missions. This paper addresses the challenging problem of high-precision autonomous pointing control of a large satellite antenna. The pointing dynamics are firstly proposed. The proportional–derivative feedback and structural filter to perform pointing maneuvers and suppress antenna vibrations are then presented. An adaptive controller to estimate actual system frequencies in the presence of modal parameters uncertainty is proposed. In order to reduce periodic errors, the modified controllers, which include the proposed adaptive controller and an active disturbance rejection filter, are then developed. The system stability and robustness are analyzed and discussed in the frequency domain. Numerical results are finally provided, and the results have demonstrated that the proposed controllers have good autonomy and robustness.

  18. PATL: A RFID Tag Localization based on Phased Array Antenna

    Science.gov (United States)

    Qiu, Lanxin; Liang, Xiaoxuan; Huang, Zhangqin

    2017-01-01

    In RFID systems, how to detect the position precisely is an important and challenging research topic. In this paper, we propose a range-free 2D tag localization method based on phased array antenna, called PATL. This method takes advantage of the adjustable radiation angle of the phased array antenna to scan the surveillance region in turns. By using the statistics of the tags’ number in different antenna beam directions, a weighting algorithm is used to calculate the position of the tag. This method can be applied to real-time location of multiple targets without usage of any reference tags or additional readers. Additionally, we present an optimized weighting method based on RSSI to increase the locating accuracy. We use a Commercial Off-the-Shelf (COTS) UHF RFID reader which is integrated with a phased array antenna to evaluate our method. The experiment results from an indoor office environment demonstrate the average distance error of PATL is about 21 cm and the optimized approach achieves an accuracy of 13 cm. This novel 2D localization scheme is a simple, yet promising, solution that is especially applicable to the smart shelf visualized management in storage or retail area. PMID:28295014

  19. A Flexible Phased-MIMO Array Antenna with Transmit Beamforming

    Directory of Open Access Journals (Sweden)

    Wen-Qin Wang

    2012-01-01

    Full Text Available Although phased-array antennas have been widely employed in modern radars, the requirements of many emerging applications call for new more advanced array antennas. This paper proposes a flexible phased-array multiple-input multiple-output (MIMO array antenna with transmit beamforming. This approach divides the transmit antenna array into multiple subarrays that are allowed to overlap each subarray coherently transmits a distinct waveform, which is orthogonal to the waveforms transmitted by other subarrays, at a distinct transmit frequency. That is, a small frequency increment is employed in each subarray. Each subarray forms a directional beam and all beams may be steered to different directions. The subarrays jointly offer flexible operating modes such as MIMO array which offers spatial diversity gain, phased-array which offers coherent directional gain and frequency diverse array which provides range-dependent beampattern. The system performance is examined by analyzing the transmit-receive beampatterns. The proposed approach is validated by extensive numerical simulation results.

  20. An adaptive Multiplicative Extened Kalman Filter for Attitude Estimation of Marine Satellite Tracking Antenna

    DEFF Research Database (Denmark)

    Wang, Yunlong; Soltani, Mohsen; Hussain, Dil muhammed Akbar

    2016-01-01

    , an adaptive Multiplicative Extended Kalman Filter (MEKF) for attitude estimation of Marine Satellite Tracking Antenna (MSTA) is presented with the measurement noise covariance matrix adjusted according to the norm of accelerometer measurements, which can significantly reduce the slamming influence from waves...

  1. The method of the antenna system positioning for satellite communication network radiomonitoring complex

    OpenAIRE

    Гребенюк, Олег Петрович

    2014-01-01

    The method of orientation of the antenna system of complex of radiomonitoring of satellite communication networks is offered. A method takes into account the features of construction and functional setting of a transport stream of standard of DVB ‑ S.

  2. Planetary gearbox condition monitoring of ship-based satellite communication antennas using ensemble multiwavelet analysis method

    Science.gov (United States)

    Chen, Jinglong; Zhang, Chunlin; Zhang, Xiaoyan; Zi, Yanyang; He, Shuilong; Yang, Zhe

    2015-03-01

    Satellite communication antennas are key devices of a measurement ship to support voice, data, fax and video integration services. Condition monitoring of mechanical equipment from the vibration measurement data is significant for guaranteeing safe operation and avoiding the unscheduled breakdown. So, condition monitoring system for ship-based satellite communication antennas is designed and developed. Planetary gearboxes play an important role in the transmission train of satellite communication antenna. However, condition monitoring of planetary gearbox still faces challenges due to complexity and weak condition feature. This paper provides a possibility for planetary gearbox condition monitoring by proposing ensemble a multiwavelet analysis method. Benefit from the property on multi-resolution analysis and the multiple wavelet basis functions, multiwavelet has the advantage over characterizing the non-stationary signal. In order to realize the accurate detection of the condition feature and multi-resolution analysis in the whole frequency band, adaptive multiwavelet basis function is constructed via increasing multiplicity and then vibration signal is processed by the ensemble multiwavelet transform. Finally, normalized ensemble multiwavelet transform information entropy is computed to describe the condition of planetary gearbox. The effectiveness of proposed method is first validated through condition monitoring of experimental planetary gearbox. Then this method is used for planetary gearbox condition monitoring of ship-based satellite communication antennas and the results support its feasibility.

  3. Antennas for Frequency Reconfigurable Phased Arrays

    NARCIS (Netherlands)

    Haider, S.N.

    2015-01-01

    Sensors such as phased array radars play a crucial role in public safety. They are unavoidable for surveillance, threat identification and post-disaster management. However, different scenarios impose immensely diverse requirements for these systems. Phased array systems occupy a large space. In add

  4. Low Cost Phased Array Antenna System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A program is proposed to research the applicability of a unique phased array technology, dubbed FlexScan, to S-band and Ku-band communications links between...

  5. An adaptive Multiplicative Extened Kalman Filter for Attitude Estimation of Marine Satellite Tracking Antenna

    DEFF Research Database (Denmark)

    Wang, Yunlong; Soltani, Mohsen; Hussain, Dil muhammed Akbar

    2016-01-01

    Satellite tracking is a challenging task for marine applications due to the disturbance from ocean waves. An Attitude Heading and Reference System (AHRS) for measuring ship attitude, based on Microelectromechanical Systems (MEMS) sensors, is a key part for satellite tracking. In this paper......, an adaptive Multiplicative Extended Kalman Filter (MEKF) for attitude estimation of Marine Satellite Tracking Antenna (MSTA) is presented with the measurement noise covariance matrix adjusted according to the norm of accelerometer measurements, which can significantly reduce the slamming influence from waves...

  6. Advanced Communication Technology Satellite (ACTS) Multibeam Antenna On-Orbit Performance

    Science.gov (United States)

    1995-01-01

    The NASA Lewis Research Center's Advanced Communication Technology Satellite (ACTS) was launched in September 1993. ACTS introduced several new technologies, including a multibeam antenna (MBA) operating at extremely short wavelengths never before used in communications. This antenna, which has both fixed and rapidly reconfigurable high-energy spot beams (150 miles in diameter), serves users equipped with small antenna terminals. Extensive structural and thermal analyses have been performed for simulating the ACTS MBA on-orbit performance. The results show that the reflector surfaces (mainly the front subreflector), antenna support assembly, and metallic surfaces on the spacecraft body will be distorted because of the thermal effects of varying solar heating, which degrade the ACTS MBA performance. Since ACTS was launched, a number of evaluations have been performed to assess MBA performance in the space environment. For example, the on-orbit performance measurements found systematic environmental disturbances to the MBA beam pointing. These disturbances were found to be imposed by the attitude control system, antenna and spacecraft mechanical alignments, and on-orbit thermal effects. As a result, the MBA may not always exactly cover the intended service area. In addition, the on-orbit measurements showed that antenna pointing accuracy is the performance parameter most sensitive to thermal distortions on the front subreflector surface and antenna support assemblies. Several compensation approaches were tested and evaluated to restore on-orbit pointing stability. A combination of autotrack (75 percent of the time) and Earth sensor control (25 percent of the time) was found to be the best way to compensate for antenna pointing error during orbit. This approach greatly minimizes the effects of thermal distortions on antenna beam pointing.

  7. Application of adaptive antenna techniques to future commercial satellite communications. Executive summary

    Science.gov (United States)

    Ersoy, L.; Lee, E. A.; Matthews, E. W.

    1987-01-01

    The purpose of this contract was to identify the application of adaptive antenna technique in future operational commercial satellite communication systems and to quantify potential benefits. The contract consisted of two major subtasks. Task 1, Assessment of Future Commercial Satellite System Requirements, was generally referred to as the Adaptive section. Task 2 dealt with Pointing Error Compensation Study for a Multiple Scanning/Fixed Spot Beam Reflector Antenna System and was referred to as the reconfigurable system. Each of these tasks was further subdivided into smaller subtasks. It should also be noted that the reconfigurable system is usually defined as an open-loop system while the adaptive system is a closed-loop system. The differences between the open- and closed-loop systems were defined. Both the adaptive and reconfigurable systems were explained and the potential applications of such systems were presented in the context of commercial communication satellite systems.

  8. Optically addressed ultra-wideband phased antenna array

    Science.gov (United States)

    Bai, Jian

    Demands for high data rate and multifunctional apertures from both civilian and military users have motivated development of ultra-wideband (UWB) electrically steered phased arrays. Meanwhile, the need for large contiguous frequency is pushing operation of radio systems into the millimeter-wave (mm-wave) range. Therefore, modern radio systems require UWB performance from VHF to mm-wave. However, traditional electronic systems suffer many challenges that make achieving these requirements difficult. Several examples includes: voltage controlled oscillators (VCO) cannot provide a tunable range of several octaves, distribution of wideband local oscillator signals undergo high loss and dispersion through RF transmission lines, and antennas have very limited bandwidth or bulky sizes. Recently, RF photonics technology has drawn considerable attention because of its advantages over traditional systems, with the capability of offering extreme power efficiency, information capacity, frequency agility, and spatial beam diversity. A hybrid RF photonic communication system utilizing optical links and an RF transducer at the antenna potentially provides ultra-wideband data transmission, i.e., over 100 GHz. A successful implementation of such an optically addressed phased array requires addressing several key challenges. Photonic generation of an RF source with over a seven-octave bandwidth has been demonstrated in the last few years. However, one challenge which still remains is how to convey phased optical signals to downconversion modules and antennas. Therefore, a feed network with phase sweeping capability and low excessive phase noise needs to be developed. Another key challenge is to develop an ultra-wideband array antenna. Modern frontends require antennas to be compact, planar, and low-profile in addition to possessing broad bandwidth, conforming to stringent space, weight, cost, and power constraints. To address these issues, I will study broadband and miniaturization

  9. Bit error rate testing of fiber optic data links for MMIC-based phased array antennas

    Science.gov (United States)

    Shalkhauser, K. A.; Kunath, R. R.; Daryoush, A. S.

    1990-06-01

    The measured bit-error-rate (BER) performance of a fiber optic data link to be used in satellite communications systems is presented and discussed. In the testing, the link was measured for its ability to carry high burst rate, serial-minimum shift keyed (SMSK) digital data similar to those used in actual space communications systems. The fiber optic data link, as part of a dual-segment injection-locked RF fiber optic link system, offers a means to distribute these signals to the many radiating elements of a phased array antenna. Test procedures, experimental arrangements, and test results are presented.

  10. SAR processing with stepped chirps and phased array antennas.

    Energy Technology Data Exchange (ETDEWEB)

    Doerry, Armin Walter

    2006-09-01

    Wideband radar signals are problematic for phased array antennas. Wideband radar signals can be generated from series or groups of narrow-band signals centered at different frequencies. An equivalent wideband LFM chirp can be assembled from lesser-bandwidth chirp segments in the data processing. The chirp segments can be transmitted as separate narrow-band pulses, each with their own steering phase operation. This overcomes the problematic dilemma of steering wideband chirps with phase shifters alone, that is, without true time-delay elements.

  11. A 2.4 GHz Cross Rhombic Antenna for a Cube Satellite Application

    Directory of Open Access Journals (Sweden)

    Jorge Sosa-Pedroza

    2014-01-01

    Full Text Available We present design and construction results of a 2.4 Ghz cross rhombic antenna to be used in a cubesat. Computational design agrees with experimental results after its construction. cross rhombic antenna is a novel planar structure of our own design, presenting circular polarization and medium gain; it is built over a RF60A substrate with εr=6.15, decreasing its size to fit the required dimensions of satellite. A special characteristic of this design is the enhancing of operational bandwidth using a technique we have been studying, related to softening the structures with sharp edges. Results show applicability and success of our technique.

  12. Antenna pointing system for satellite tracking based on Kalman filtering and model predictive control techniques

    Science.gov (United States)

    Souza, André L. G.; Ishihara, João Y.; Ferreira, Henrique C.; Borges, Renato A.; Borges, Geovany A.

    2016-12-01

    The present work proposes a new approach for an antenna pointing system for satellite tracking. Such a system uses the received signal to estimate the beam pointing deviation and then adjusts the antenna pointing. The present work has two contributions. First, the estimation is performed by a Kalman filter based conical scan technique. This technique uses the Kalman filter avoiding the batch estimator and applies a mathematical manipulation avoiding the linearization approximations. Secondly, a control technique based on the model predictive control together with an explicit state feedback solution are obtained in order to reduce the computational burden. Numerical examples illustrate the results.

  13. Optically controlled phased-array antenna with PSK communications

    Science.gov (United States)

    Cooper, Martin J.; Sample, Peter; Lewis, Meirion F.; Wilson, Rebecca A.

    2004-11-01

    An optically controlled RF/microwave/mm-wave phased array antenna has been developed operating at 10 GHz with 30 kHz reconfiguration rate via the use of a micromachined silicon Spatial Light Modulator. A communications function has been demonstrated with a variety of Phase Shift Keying modulation schemes (BPSK, QPSK, MSK) at data rates up to 200 Mbit/s and low BER (<1×10-9). A single channel has been demonstrated at 35 GHz. The properties of photonic components are taken advantage of in several ways: (i) since the carrier frequency is derived from heterodyning of lasers, it is tuneable from almost DC-100 GHz, (ii) the use of optical fiber allows for EMI immune antenna remoting, and (iii) the wide information bandwidth of optical modulators, which in this configuration is carrier frequency independent. The above is achieved in a lightweight and compact format, with considerable scope for further reductions in size and weight.

  14. Adaptive multibeam antennas for spacelab. Phase A: Feasibility study

    Science.gov (United States)

    Allen, C. C.; Applebaum, S. P.; Popowsky, W. J.; Wouch, G.

    1976-01-01

    The feasibility was studied of using adaptive multibeam multi-frequency antennas on the spacelab, and to define the experiment configuration and program plan needed for a demonstration to prove the concept. Three applications missions were selected, and requirements were defined for an L band communications experiment, an L band radiometer experiment, and a Ku band communications experiment. Reflector, passive lens, and phased array antenna systems were considered, and the Adaptive Multibeam Phased Array (AMPA) was chosen. Array configuration and beamforming network tradeoffs resulted in a single 3m x 3m L band array with 576 elements for high radiometer beam efficiency. Separate 0.4m x 0.4 m arrays are used to transmit and receive at Ku band with either 576 elements or thinned apertures. Each array has two independently steerable 5 deg beams, which are adaptively controlled.

  15. A Multi-Band Photonic Phased Array Antenna for High-Data Rate Communication Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Multi-band phased array antenna (PAA) can reduce the number of antennas on shipboard platforms while offering significantly improved performance. In order to steer...

  16. A Multi-band Photonic Phased Array Antenna for High-Date Rate Communication Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Multi-band phased array antenna (PAA) can reduce the number of antennas on shipboard platforms while offering significantly improved performance. In order to steer...

  17. Low Profile and Low Cost Antenna Technology for Satellite TV Reception on Sports Utility Vehicles (SUV) for the US Market

    Science.gov (United States)

    Vazquez, F. Javier; Pearson, Robert A.; Driscoll, Barry G.

    2003-07-01

    A low profile scanning antenna for reception of satellite TV has been developed for the US market compatible with existing DBS Ku band satellite infrastructure. This antenna technology does not require active RF components and it is inherently low cost (in the order of a few hundred dollars even in moderate production volumes). The antenna is able to scan a circularly polarised beam in the range 20 to 69 degrees, covering three DBS satellites in the US including some margin for vehicle tilt. An antenna demonstrator of 115 mm height, including the radome and tracking electronics has been built and measured. Live tests were performed in the US during 2002 to determine realistic link margins and antenna specifications. A product development is currently being undertaken to turn the demonstrator unit into a product for the US market by the end of 2003.

  18. A Multibeam Dual-Band Orthogonal Linearly Polarized Antenna Array for Satellite Communication on the Move

    Directory of Open Access Journals (Sweden)

    Yi Liu

    2015-01-01

    Full Text Available The design and simulation of a 10 × 8 multibeam dual-band orthogonal linearly polarized antenna array operating at Ku-band are presented for transmit-receive applications. By using patches with different coupling methods as elements, both perpendicular polarization in 12.25–12.75 GHz band and horizontal polarization in 14.0–14.5 GHz band are realized in a shared antenna aperture. A microstrip Rotman lens is employed as the beamforming network with 7 input ports, which can generate a corresponding number of beams to cover −30°–30° with 5 dB beamwidth along one dimension. This type of multibeam orthogonal linearly polarized planar antenna is a good candidate for satellite communication (SatCom.

  19. Analysis of friction effects on satellite antenna driving mechanism with clearance joints

    Science.gov (United States)

    Bai, Z. F.; Chen, J.; Bian, S.; Shi, X.

    2017-01-01

    The existence of clearance in joints of mechanism is inevitable. In this paper, the friction effects in clearance joints on dynamic responses of driving mechanism of satellite antenna are studied. Considering clearances in joints, the contact force model in clearance joints is established using a nonlinear continuous contact force model and the friction effect is considered by using a modified Coulomb friction model. Then the dual-axis driving mechanism of satellite antenna with clearance joints is used as the application example. The numerical simulation of dual-axis driving mechanism with clearance joints is presented. The friction effects of clearance joint on dynamic responses of the dual-axis driving mechanism are discussed and analyzed quantitatively for four cases with different friction coefficients. The investigation results show that the increase of friction coefficient will decrease the vibration amplitude of the driving mechanism system.

  20. Demonstration of Two-Way Extremely High Frequency (EHF) Satellite Communication (SATCOM) Using Submarine-Survivable Phased Arrays

    Science.gov (United States)

    2009-01-01

    successfully using both the Military Strategic and Tactical Relay (MILSTAR) and Ultra High Frequency Follow-On ( UFO ) military satellites. The antennas...a Navy-qualified submarine FOT and High Power Amplifier (HPA) system, toward a MILSTAR or UFO EHF satellite. FULL-DUPLEX STATIC TESTING...both the K & Q band phased arrays. Both the MILSTAR and UFO satellites were used for this testing, based on availability. Using the Type 8 Mod 3

  1. Deploying process modeling and attitude control of a satellite with a large deployable antenna

    OpenAIRE

    Zhigang Xing; Gangtie Zheng

    2014-01-01

    Modeling and attitude control methods for a satellite with a large deployable antenna are studied in the present paper. Firstly, for reducing the model dimension, three dynamic models for the deploying process are developed, which are built with the methods of multi-rigid-body dynamics, hybrid coordinate and substructure. Then an attitude control method suitable for the deploying process is proposed, which can keep stability under any dynamical parameter variation. Subsequently, this attitude...

  2. A MEMS-based Adaptive AHRS for Marine Satellite Tracking Antenna

    DEFF Research Database (Denmark)

    Wang, Yunlong; Hussain, Dil Muhammed Akbar; Soltani, Mohsen

    2015-01-01

    Satellite tracking is a challenging task for marine applications. An attitude determination system should estimate the wave disturbances on the ship body accurately. To achieve this, an Attitude Heading Reference System (AHRS) based on Micro-Electro-Mechanical Systems (MEMS) sensors, composed...... of three-axis gyroscope, accelerometer and magnetometer, is developed for Marine Satellite Tracking Antenna (MSTA). In this paper, the attitude determination algorithm is improved using an adaptive mechanism that tunes the attitude estimator parameters based on an estimation of ship motion frequency...

  3. Design and Implementation of a Beam Forming Network for a Phased Array Antenna

    Directory of Open Access Journals (Sweden)

    S. Devimeena

    2015-03-01

    Full Text Available This dissertation presents a beam forming network (BFN for phased array antenna-based on coherently radiating periodic structure (CORPS. The elements of CORPS are selected in such a way to obtain broad band characteristics, good return loss and good isolation between the radiating elements. These elements were arranged in such a way that the BFN naturally produces Gaussian amplitude. This methodology reduces the complexity of the conventional phased array design making it more flexible and minimizing the loss of energy inside the structure. A phase shifter design is proposed for the CORPS. The entire BFN’s sub-blocks have been designed for the frequency band of 5.925 GHz to 6.425 GHz, which find applications in communication satellite, fixed wireless systems.Defence Science Journal, Vol. 65, No. 1, January 2015, pp.46-52, DOI:http://dx.doi.org/10.14429/dsj.65.6940

  4. High-Sensitivity Phased Arrays for Radio Astronomy and Satellite Communications

    Science.gov (United States)

    Diao, Junming

    Radio astronomy is used to study stars, galaxies, black holes and gas clouds radiation at radio frequencies. Detecting extremely weak signals from deep space radio sources requires high sensitive feed system associated with large dish antennas. The key figure of merit is survey speed, or the time required to map a region of the sky to a given source flux density. Survey speed is proportional to the frequency bandwidth, the field of view or observable region of the sky, and the squared sensitivity, where sensitivity is related to reflector aperture efficiency and system noise temperature. Compared to the traditional single feed, phased array feeds with significantly expanded field of view are considered as the next generation feed for radio telescope. This dissertation outlines the design, analysis and measurement of high sensitivity L-band and mm-wave phased array feeds for the 100-meter Green Bank Telescope. Theoretical works for radio astronomy includes design guideline for high sensitivity phased array feed, fundamental frequency bandwidth limit, array antenna loss influenced by mutual coupling and beamformer coefficients and possibility of superdirectivity for radio telescopes and other antennas. These study are helpful to understand and guide the design of a phased array feed system. In the absence of dish antennas, sparse phased arrays with aperiodic structure have been developed for satellite communications. A compromise between the peak side lobe level, array element density, directivity and design complexity is studied. We have found that the array peak side lobe level can be reduced by enhancing the array element direction at the main lobe direction, increasing the array element density and enlarging the array size. A Poynting streamline approach develops to understand the properties of a receiving antenna and the mutual coupling effects between array elements. This method has been successfully used to generate effective area shape for many types of

  5. Design of an electric power system with incorporation of a phased array antenna for OLFAR

    NARCIS (Netherlands)

    Klein, J.M.; Budianu, A.; Bentum, M.J.; Engelen, S.; Verhoeven, C.J.M.

    2013-01-01

    The Orbiting Low Frequency Antennas for Radio Astronomy (OLFAR) project is investigating the feasibility of an orbiting low frequency radio telescope. The radio telescope is formed using a swarm of nano-satellites equipped with astronomical antennas, conceivably orbiting the Moon or the second Lagra

  6. Switchable Phased Antenna Array with Passive Elements for 5G Mobile Terminals

    DEFF Research Database (Denmark)

    Syrytsin, Igor A.; Zhang, Shuai; Pedersen, Gert F.

    2017-01-01

    In this paper, a reconfigurable phased antenna array system is constructed for the mobile terminals in the context of 5G communication system. The proposed antenna system operates at the resonance frequency of 28 GHz. The reconfigurability of the antenna element is achieved by using a passive slot...

  7. Switchable Phased Antenna Array with Passive Elements for 5G Mobile Terminals

    DEFF Research Database (Denmark)

    Syrytsin, Igor A.; Zhang, Shuai; Pedersen, Gert F.

    2017-01-01

    In this paper, a reconfigurable phased antenna array system is constructed for the mobile terminals in the context of 5G communication system. The proposed antenna system operates at the resonance frequency of 28 GHz. The reconfigurability of the antenna element is achieved by using a passive slo...

  8. Evolution from a hinge actuator mechanism to an antenna deployment mechanism for use on the European large communications satellite (L-SAT/OLYMPUS)

    Science.gov (United States)

    Death, M. D.

    1984-01-01

    The evolution of an Antenna Deployment Mechanism (ADM) from a Hinge Actuator Mechanism (HAM) is described as it pertains to the deployment of large satellite antennas. Design analysis and mechanical tests are examined in detail.

  9. A technique for measurement of earth station antenna G/T by radio stars and Applications Technology Satellites.

    Science.gov (United States)

    Kochevar, H. J.

    1972-01-01

    A new technique has been developed to accurately measure the G/T of a small aperture antenna using geostationary satellites and the well established radio star method. A large aperture antenna having the capability of accurately measuring its G/T by using a radio star of known power density is used to obtain an accurate G/T to use as a reference. The CNR of both the large and small aperture antennas are then measured using an Applications Technology Satellite (ATS). After normalizing the two C/N ratios to the large antenna system noise temperature the G/T or the gain G of the small aperture antenna can then be determined.

  10. Novel Microstrip Patch Antennas with Frequency Agility, Polarization Reconfigurability, Dual Null Steering Capability and Phased Array Antenna with Beam Steering Performance

    Science.gov (United States)

    Babakhani, Behrouz

    Nowadays the wireless communication technology is playing an important role in our daily life. People use wireless devices not only as a conventional communication device but also as tracking and navigation tool, web browsing tool, data storage and transfer tool and so for many other reasons. Based on the user demand, wireless communication engineers try to accommodate as many as possible wireless systems and applications in a single device and therefore, creates a multifunctional device. Antenna, as an integral part of any wireless communication systems, should also be evolved and adjusted with development of wireless transceiver systems. Therefore multifunctional antennas have been introduced to support and enhance the functionality on modern wireless systems. The main focus and contribution of this thesis is design of novel multifunctional microstrip antennas with frequency agility, polarization reconfigurablity, dual null steering capability and phased array antenna with beam steering performance. In this thesis, first, a wide bandwidth(1.10 GHz to 1.60 GHz) right-handed circularly polarized (RHCP) directional antenna for global positioning system (GPS) satellite receive application has been introduced which covers all the GPS bands starting from L1 to L5. This design consists of two crossed bow-tie dipole antennas fed with sequentially phase rotated feed network backed with an artificial high impedance surface (HIS) structure to generate high gain directional radiation patterns. This design shows good CP gain and axial ratio (AR) and wide beamwidth performance. Although this design has good radiation quality, the size and the weight can be reduced as future study. In the second design, a frequency agile antenna was developed which also covers the L-band (L1 to L5) satellite communication frequencies. This frequency agile antenna was designed and realized by new implementation of varactor diodes in the geometry of a circular patch antenna. Beside wide frequency

  11. A bionic approach to mathematical modeling the fold geometry of deployable reflector antennas on satellites

    Science.gov (United States)

    Feng, C. M.; Liu, T. S.

    2014-10-01

    Inspired from biology, this study presents a method for designing the fold geometry of deployable reflectors. Since the space available inside rockets for transporting satellites with reflector antennas is typically cylindrical in shape, and its cross-sectional area is considerably smaller than the reflector antenna after deployment, the cross-sectional area of the folded reflector must be smaller than the available rocket interior space. Membrane reflectors in aerospace are a type of lightweight structure that can be packaged compactly. To design membrane reflectors from the perspective of deployment processes, bionic applications from morphological changes of plants are investigated. Creating biologically inspired reflectors, this paper deals with fold geometry of reflectors, which imitate flower buds. This study uses mathematical formulation to describe geometric profiles of flower buds. Based on the formulation, new designs for deployable membrane reflectors derived from bionics are proposed. Adjusting parameters in the formulation of these designs leads to decreases in reflector area before deployment.

  12. Slow and fast light in SOA-EA structures for phased-array antennas

    DEFF Research Database (Denmark)

    Sales, S.; Öhman, Filip; Bermejo, A.;

    We present an SOA-EA structure for controlling the phase and amplitude of optically fed phased-array antennas. Phase shifts of 40 degrees are obtained through slow and fast light effects by changing only the reverse voltage.......We present an SOA-EA structure for controlling the phase and amplitude of optically fed phased-array antennas. Phase shifts of 40 degrees are obtained through slow and fast light effects by changing only the reverse voltage....

  13. A Fully Reconfigurable Polarimetric Phased Array Antenna Testbed

    Directory of Open Access Journals (Sweden)

    Sudantha Perera

    2014-01-01

    Full Text Available The configurable phased array demonstrator (CPAD is a low-cost, reconfigurable, small-scale testbed for the dual-polarized array antenna and radar prototype. It is based on the concept that individual transmit and receive (TR modules and radiating elements can be configured in different ways to study the impact of various array manifolds on radiation pattern performance. For example, CPAD is configured as (a a 4 × 4 planar array, (b a planar array with mirror configuration, and (c a circular array to support the multifunctional phased array radar (MPAR system risk reduction studies. System descriptions are given in detail, and measurements are made and results are analyzed.

  14. Disturbance of flexible antenna surface on a satellite antenna%柔性天线面对星载天线的扰动研究

    Institute of Scientific and Technical Information of China (English)

    游斌弟; 赵志刚; 魏承; 赵阳

    2011-01-01

    To study disturbance of flexible antenna surface on a free-floating satellite antenna, the fixed-interface component-mode synthesis method and Lagrange's equations were used to achieve a lower order dynamic model by modal truncation. Under large scale motions, the rigid-flexible coupled dynamic model of the free-floating flexible satellite antenna was deduced through using compatibility relations at the interface between axis end and antenna surface, and neglecting the elastic deformation of the flexible antenna surface. So the model increased the computing efficiency without losing much accuracy. Finally, the free-floating satellite antenna dynamic behavior was analyzed considering the flexible antenna surface as a rigid body and a flexible one, separately. The result showed that the flexible antenna surface has little effect on the satellite base attitude and the antenna pointing at initial stage, but its own elastic vibration grows with the continuous action of joint torques; further, it makes the system vibrate and the deviations of the satellite base attitude and the antenna pointing become larger; the satellite antenna pointing accuracy is seriously affected. The results were valuable for analysis and control of satellite antenna pointing accuracy.%针对柔性天线面对星载天线的扰动问题,应用固定界面模态综合法和Lagrange方程,截取柔性天线面低阶模态,缩减星载天线系统的自由度,并通过轴末端与天线面交界面的协调关系,推导了大范围运动的星载天线刚柔耦合动力学模型,克服了忽略天线面弹性变形对刚体大范围运动的影响,所建立的耦合动力学模型计算效率高并具有足够的精度.考虑天线面为刚体和柔体情况,分别对星载天线系统进行仿真并进行对比分析,结果表明,初始时刻柔性天线面对卫星本体姿态和天线指向影响很小,随着关节力矩持续作用,激起柔性天线面震荡,加剧自身的弹性振动,进而

  15. 低轮廓动中通天线研究现状%Research Status of Low Profile Antennas in Satellite Communication on-the-move

    Institute of Scientific and Technical Information of China (English)

    李琳; 万继响

    2015-01-01

    针对目前卫星通信系统对天线性能、形式的需求,回顾了卫星移动通信中天线的应用背景和发展历程,对国内外低剖面动中通天线的类型进行了综述;详细介绍了平板阵列、一维和二维有源相控阵天线的工作原理和代表产品,分析了各自产品在具体使用环境中的技术指标及优缺点;进一步研究了低轮廓动中通天线的关键技术;最后对卫星移动通信天线的发展趋势进行了展望。%According to the requirements of antenna performance and profile in satellite communication, the background and development of antenna for satellite communications on-the-move is firstly reviewed and the type of the low profile anten-na for SOTM abroad is then described. Moreover, the plate antenna and the 1-D and 2-D electronic scanned active phased arrays are introduced in detail. The advantages as well as the shortcomings and the characteristics of these products under practical condition are analyzed. Furthermore, other key technologies about low profile antenna are presented. Finally, the development trend of the low profile antenna of SOTM is predicted.

  16. Large deployable antenna to be loaded on Engineering Test Satellite-8; Gijutsu shiken eisei VIII gata tosaiyo ogata tenkai antena

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A large deployable antenna to be loaded on the Engineering Test Satellite-8, which is scheduled to be launched in 2002, is about 19m x 17m, the world largest on-satellite deployable antenna/reflection mirror, with two sets to be loaded for transmission and reception. This antenna is featured by a metallic mesh structure for the reflection surface and by a module structure in which fourteen hexagonal modules are combined comprising the entirety. While a test is conducted using the development model, verification is scheduled on the method of antenna deployment analysis examined so far and on the validity of the method for estimating the shape of the mesh reflection face under zero gravity. The results thus obtained will be reflected on the design of flight articles for which high quality is required. (translated by NEDO)

  17. A Phased Array Antenna Signal Processing Structure, a Method and a Computer Program Product

    NARCIS (Netherlands)

    Vliet, F.E. van; Dijk, R. van

    2011-01-01

    The invention relates to a phased array antenna signal processing structure. The structure comprises a processor that includes a digital beam forming unit for generating partial beam data from digitized samples of a set of phased array antenna elements. The processor further comprises a set of input

  18. An Optimal Beamforming Algorithm for Phased-Array Antennas Used in Multi-Beam Spaceborne Radiometers

    DEFF Research Database (Denmark)

    Iupikov, O. A.; Ivashina, M. V.; Pontoppidan, K.;

    2015-01-01

    Strict requirements for future spaceborne ocean missions using multi-beam radiometers call for new antenna technologies, such as digital beamforming phased arrays. In this paper, we present an optimal beamforming algorithm for phased-array antenna systems designed to operate as focal plane arrays...

  19. An Efficient Beam Steerable Antenna Array Concept for Airborne Applications

    OpenAIRE

    Aliakbarian, H.; Van der Westhuizen, E.; Wiid, R.; Volskiy, V.; R. Wolhuter; G. A. E. Vandenbosch

    2014-01-01

    Deployment of a satellite borne, steerable antenna array with higher directivity and gain in Low Earth Orbit makes sense to reduce ground station complexity and cost, while still maintaining a reasonable link budget. The implementation comprises a digitally beam steerable phased array antenna integrated with a complete system, comprising the antenna, hosting platform, ground station, and aircraft based satellite emulator to facilitate convenient aircraft based testing of the antenna array and...

  20. Fully Printed, Flexible, Phased Array Antenna for Lunar Surface Communication

    Science.gov (United States)

    Subbaraman, Harish; Hen, Ray T.; Lu, Xuejun; Chen, Maggie Yihong

    2013-01-01

    NASAs future exploration missions focus on the manned exploration of the Moon, Mars, and beyond, which will rely heavily on the development of a reliable communications infrastructure from planetary surface-to-surface, surface-to-orbit, and back to Earth. Flexible antennas are highly desired in many scenarios. Active phased array antennas (active PAAs) with distributed control and processing electronics at the surface of an antenna aperture offer numerous advantages for radar communications. Large-area active PAAs on flexible substrates are of particular interest in NASA s space radars due to their efficient inflatable package that can be rolled up during transportation and deployed in space. Such an inflatable package significantly reduces stowage volume and mass. Because of these performance and packaging advantages, large-area inflatable active PAAs are highly desired in NASA s surface-to-orbit and surface-to-relay communications. To address the issues of flexible electronics, a room-temperature printing process of active phased-array antennas on a flexible Kapton substrate was developed. Field effect transistors (FETs) based on carbon nanotubes (CNTs), with many unique physical properties, were successfully proved feasible for the PAA system. This innovation is a new type of fully inkjet-printable, two-dimensional, high-frequency PAA on a flexible substrate at room temperature. The designed electronic circuit components, such as the FET switches in the phase shifter, metal interconnection lines, microstrip transmission lines, etc., are all printed using a special inkjet printer. Using the developed technology, entire 1x4, 2x2, and 4x4 PAA systems were developed, packaged, and demonstrated at 5.3 GHz. Several key solutions are addressed in this work to solve the fabrication issues. The source/drain contact is developed using droplets of silver ink printed on the source/drain areas prior to applying CNT thin-film. The wet silver ink droplets allow the silver to

  1. PS2007 Satellite Meeting on Photosynthetic Antennas, 19-22 July 2007, Drymen, Scotland

    Energy Technology Data Exchange (ETDEWEB)

    Robert E. Blankenship

    2009-06-04

    A Satellite Workshop of the 14th International Congress on Photosynthesis on the topic of photosynthetic light-harvesting systems was held on 18-21 July 2007, at the Buchanan Arms Hotel in Drymen, Scotland, near Glasgow. This meeting continued the tradition of satellite light-harvesting conferences occurring prior to the last five international photosynthesis congresses in Japan, France, Hungary, Australia and Canada, dating from 1992. With an attendance of 124 participants, this Workshop represents an intimate gathering of scientists interested in a thorough coverage of the light-harvesting aspects of photosynthesis. A significant amount of time was set aside for discussion and poster sessions. The organizers were: Richard J. Cogdell, UK (Chairperson), Alastair T. Gardiner, UK, Conrad W. Mullineaux, UK, Robert A. Niederman, USA, Robert E. Blankenship, USA, Harry Frank, USA, Bruno Robert, France. Sessions were focused on new concepts relating to the function, regulation, assembly, photoprotection and evolution of a wide variety of antenna systems. Cutting-edge scientific methods used to study these systems that were covered included time-resolved and single-molecule spectroscopy, structure determination by X-ray diffraction, NMR and electron and atomic force microscopy, molecular genetics, protein chemistry, model systems and theory. A central theme was how emerging high-resolution structural information on antenna proteins continues to provide an enhanced understanding of areas ranging from the kinetics of energy transfer processes to the assembly of the photosynthetic apparatus.

  2. Subcutaneous implantation of satellite transmitters with percutaneous antennae into male polar bears (Ursus maritimus)

    Science.gov (United States)

    Mulcahy, D.M.; Garner, G.

    1999-01-01

    Male polar bears (Ursus maritimus) have not been successfully instrumented with satellite transmitters because they readily shed collar-mounted transmitters. Seven male polar bears were captured on the pack ice off the northern coast of Alaska and surgically implanted with satellite transmitters with percutaneous antennae into the subcutaneous space of the dorsal cervical region. Transmitters failed prematurely with lifetimes of 30-161 days (x?? = 97 days). Efforts to relocate implanted bears after transmitters failed were not successful. The mean number of location solutions per transmitter was 204 (range 118-369). An average of 10% and 19% of the locations were accurate to < 150 m and to 150-350 m, respectively. Our successful tracking of male polar bears, the high quality of locations obtained from transmitters with percutaneous antennae implanted in the subcutaneous space, and the low visibility of such units make further technical development worthwhile if the reason for premature failure of the transmitters can be determined. Copyright 1999 by American Association of Zoo Veterinarians.

  3. The application of taylor weighting, digital phase shifters, and digital attenuators to phased-array antennas.

    Energy Technology Data Exchange (ETDEWEB)

    Brock, Billy C.

    2008-03-01

    Application of Taylor weighting (taper) to an antenna aperture can achieve low peak sidelobes, but combining the Taylor weighting with quantized attenuators and phase shifters at each radiating element will impact the performance of a phased-array antenna. An examination of array performance is undertaken from the simple point of view of the characteristics of the array factor. Design rules and guidelines for determining the Taylor-weighting parameters, the number of bits required for the digital phase shifter, and the dynamic range and number of bits required for the digital attenuator are developed. For a radar application, when each element is fed directly from a transmit/receive module, the total power radiated by the array will be reduced as a result of the taper. Consequently, the issue of whether to apply the taper on both transmit and receive configurations, or only on the receive configuration is examined with respect to two-way sidelobe performance.

  4. Testing mensuration of the vertical component deviation of phase center of GPS antenna combinations

    Energy Technology Data Exchange (ETDEWEB)

    Gao, W.; Xu, S.; Li, L. [Wuhan University, Wuhan (China). School of Geodesy and Geomatics

    2004-07-01

    Five models of three types of Topcon, Trimble and Leica GPS receiver antennas were combined in pairs and tested using outdoor antenna mensuration. The differences of antenna phase center vertical component deviations of all combinations were figured out and the mm-level measuring precision was achieved when Bernese software was used to process the data. It is verified by the practical example that the difference of the same model of same type of GPS receiver antennas phase center vertical component deviations is about 1 mm or less than 1 mm. And that the difference of the different model of same type or different types of GPS receiver antennas phase center vertical component deviations is very big, and reaches several mm or several cm. Such difference must be corrected in order to obtain the exact and credible distortion value of height component. 4 refs., 3 figs., 3 tabs.

  5. A 28 GHz FR-4 Compatible Phased Array Antenna for 5G Mobile Phone Applications

    DEFF Research Database (Denmark)

    Ojaroudiparchin, Naser; Shen, Ming; Pedersen, Gert F.

    2015-01-01

    The design of a 28 GHz phased array antenna for future fifth generation (5G) mobile-phone applications has been presented in this paper. The proposed antenna can be implemented using low cost FR-4 substrates, while maintaining good performance in terms of gain and efficiency. This is achieved...

  6. Circularly Polarized Planar Helix Phased Antenna Array for 5G Mobile Terminals

    DEFF Research Database (Denmark)

    Syrytsin, Igor A.; Zhang, Shuai; Pedersen, Gert F.

    2017-01-01

    In this paper, a planar helix mobile phased antenna array is proposed for 5th generation communication systems with operating frequency of 28GHz. The proposed array displays circular polarization in the endfire direction. Over 65 degrees of axial ratio beamwidth and 7GHz of axial ratio bandwidth...... has been achieved in the proposed design. The coverage performance of the proposed phased antenna array has also been studied by using the coverage efficiency metric. Coverage efficiency of 50 % at 5 dBi gain is achieved by the proposed phased mobile antenna array....

  7. Bit-error-rate testing of fiber optic data links for MMIC-based phased array antennas

    Science.gov (United States)

    Shalkhauser, K. A.; Kunath, R. R.; Daryoush, A. S.

    1990-01-01

    The measured bit-error-rate (BER) performance of a fiber optic data link to be used in satellite communications systems is presented and discussed. In the testing, the link was measured for its ability to carry high burst rate, serial-minimum shift keyed (SMSK) digital data similar to those used in actual space communications systems. The fiber optic data link, as part of a dual-segment injection-locked RF fiber optic link system, offers a means to distribute these signals to the many radiating elements of a phased array antenna. Test procedures, experimental arrangements, and test results are presented.

  8. A phased array antenna for Doppler reflectometry in ASDEX upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, Stefan; Lechte, Carsten; Kasparek, Walter [IGVP, Universitaet Stuttgart, D-70569 Stuttgart (Germany); Hennequin, Pascale [Laboratoire de Physique des Plasmas, CNRS, Ecole Polytech., F-91128 Palaiseau (France); Conway, Garrard; Happel, Tim [Max-Planck-Institut fuer Plasmaphysik, D-85748 Garching (Germany); Collaboration: ASDEX Upgrade Team

    2016-07-01

    In a toroidal plasma, Doppler reflectometry (DR) allows investigating electron density fluctuations with finite k {sub perpendicular} {sub to}. The injected microwave beam's frequency determines the radial position of the probed region, its tilt angle selects the wavenumber satisfying the Bragg condition for backscattering. The rotation velocity can be calculated from the Doppler shift of the backscattered signal's frequency. By varying the injected frequency, radial profiles can be reconstructed. Varying the tilt angle resolves the k {sub perpendicular} {sub to} -spectrum of the fluctuations. For DR, a pair of phased array antennas (PAAs) has been designed, built, and installed in the ASDEX Upgrade tokamak. Beam steering is done by slightly changing the injected frequency, thus, the PAAs do not need any movable parts or electronics inside the vacuum vessel. From 75 to 105 GHz, the PAAs feature 13 frequency bands, each with an angular scan range of -20 to +20 {sup circle}. So, for each angle, there are 13 radial positions to be probed. The results from PAA characterisation, commissioning, and first DR measurements are presented.

  9. Understanding and optimizing microstrip patch antenna cross polarization radiation on element level for demanding phased array antennas in weather radar applications

    Science.gov (United States)

    Vollbracht, D.

    2015-11-01

    The antenna cross polarization suppression (CPS) is of significant importance for the accurate calculation of polarimetric weather radar moments. State-of-the-art reflector antennas fulfill these requirements, but phased array antennas are changing their CPS during the main beam shift, off-broadside direction. Since the cross polarization (x-pol) of the array pattern is affected by the x-pol element factor, the single antenna element should be designed for maximum CPS, not only at broadside, but also for the complete angular electronic scan (e-scan) range of the phased array antenna main beam positions. Different methods for reducing the x-pol radiation from microstrip patch antenna elements, available from literature sources, are discussed and summarized. The potential x-pol sources from probe fed microstrip patch antennas are investigated. Due to the lack of literature references, circular and square shaped X-Band radiators are compared in their x-pol performance and the microstrip patch antenna size variation was analyzed for improved x-pol pattern. Furthermore, the most promising technique for the reduction of x-pol radiation, namely "differential feeding with two RF signals 180° out of phase", is compared to single fed patch antennas and thoroughly investigated for phased array applications with simulation results from CST MICROWAVE STUDIO (CST MWS). A new explanation for the excellent port isolation of dual linear polarized and differential fed patch antennas is given graphically. The antenna radiation pattern from single fed and differential fed microstrip patch antennas are analyzed and the shapes of the x-pol patterns are discussed with the well-known cavity model. Moreover, two new visual based electromagnetic approaches for the explanation of the x-pol generation will be given: the field line approach and the surface current distribution approach provide new insight in understanding the generation of x-pol component in microstrip patch antenna radiation

  10. An experimental 20/30 GHz communications satellite conceptual design employing multiple-beam paraboloid reflector antennas

    Science.gov (United States)

    Goldman, A. M., Jr.

    1980-01-01

    An experimental 20/30 GHz communications satellite conceptual design is described which employs multiple-beam paraboloid reflector antennas coupled to a TDMA transponder. It is shown that the satellite employs solid state GaAs FET power amplifiers and low noise amplifiers while signal processing and switching takes place on-board the spacecraft. The proposed areas to be served by this satellite would be the continental U.S. plus Alaska, Hawaii, Puerto Rico, and the Virgin Islands, as well as southern Canada and Mexico City. Finally, attention is given to the earth stations which are designed to be low cost.

  11. Unveiling Magnetic Dipole Radiation in Phase-Reversal Leaky-Wave Antennas

    CERN Document Server

    Gupta, Shulabh; Caloz, Christophe

    2014-01-01

    The radiation principle of travelling-wave type phase-reversal antennas is explained in details, unveiling the presence of magnetic-dipole radiation in addition to well-known electric dipole radiation. It is point out that such magnetic dipole radiation is specific to the case of traveling-wave phase-reversal antennas whereas only electric-dipole radiation exists in resonant-type phase-reversal antennas. It is shown that a phase-reversal travelling-wave antenna alternately operates as an array of magnetic dipoles and an array of electric-dipoles during a time-harmonic period. This radiation mechanism is confirmed through both full-wave and experimental results.

  12. Low-loss and programmable integrated photonic beamformer for electronically-steered broadband phased array antennas

    NARCIS (Netherlands)

    Zhuang, Leimeng; Marpaung, David; Burla, Maurizio; Roeloffzen, Chris; Beeker, Willem; Leinse, Arne; Dijk, van Paul

    2011-01-01

    Recently we have reported the dev electronically-steered Ku-band (10.7-12.75 G antenna system employing an integrated photonic beamformer, which is intended to be applied on high-speed transport vehicles for mobile reception of digital video broadcasting via satellite signals (1). Besides the advant

  13. Method for Fabricating and Packaging an M.Times.N Phased-Array Antenna

    Science.gov (United States)

    Subbaraman, Harish (Inventor); Xu, Xiaochuan (Inventor); Chen, Yihong (Inventor); Chen, Ray T. (Inventor)

    2017-01-01

    A method for fabricating an M.times.N, P-bit phased-array antenna on a flexible substrate is disclosed. The method comprising ink jet printing and hardening alignment marks, antenna elements, transmission lines, switches, an RF coupler, and multilayer interconnections onto the flexible substrate. The substrate of the M.times.N, P-bit phased-array antenna may comprise an integrated control circuit of printed electronic components such as, photovoltaic cells, batteries, resistors, capacitors, etc. Other embodiments are described and claimed.

  14. A Microstrip Second-Iteration Square Koch Dipole Antenna for TT&C Downlink Applications in Small Satellites

    Directory of Open Access Journals (Sweden)

    Jorge Simón

    2017-01-01

    Full Text Available A microstrip second-iteration square Koch dipole fractal antenna is presented. This meandered antenna has a total length of 56.56 cm including its feed gap and was printed on the diagonal of a 100 mm × 100 mm PCB card that acts as CubeSat face. The antenna that was designed to optimize space shows acceptable performance at its resonance frequency of 455 MHz within the 70-centimeter band, a band that is commonly used for TTC CubeSat subsystems. The designed fractal antenna shows a reflection coefficient below −20 dB, a VSWR below 1.2, a −10 dB bandwidth of 50 MHz, and impedance magnitude of 56 Ω, while the average maximum gain around its resonance frequency is 2.14 dBi. All these parameters make this designed antenna suitable for small satellite applications at a band where a linear λ/2 dipolar antenna working at 455 MHz would be about 32.97 cm long, which does not fit within the largest dimension of a CubeSat face corresponding to 14.14 cm.

  15. Design of smoothed multi-flared antenna for multi-frequency reception of direct transmission from meteorological satellites

    Science.gov (United States)

    Yasodha, Polisetti; Jayaraman, Achuthan; Kesarkar, Amit P.; Thawait, Prateek

    2016-07-01

    The direct radiance data assimilation is found to be advantageous for the numerical weather prediction over short and medium range. Therefore reception of satellite radiance in real time is important. Satellite earth station is the preferred choice for direct reception of this data, which is voluminous. High Rate Information being transmitted from these satellites operating in L, S, C and X bands needs to be received. A commercial wide band antenna is not preferred for such application, as it operates uniformly over the entire frequency range in these bands and may create interference over the unwanted frequencies. As the frequencies of interest occupy only a small portion of these bands, it is essential to design a horn antenna, which receives only specified frequencies and filter other frequencies. In this work, we have designed a multi-flare multi-frequency cylindrical horn antenna for reception of direct transmission from meteorological satellites. This earth station antenna tracks selected satellites working over specified frequency ranges, which are 1.694-1.703 GHz, 2.0-2.06 GHz, 4.5-4.6 GHz and 7.8-7.9 GHz in L, S, C and X bands respectively. Cylindrical waveguides for the frequencies, 1.6, 2, 4.5 and 8 GHz are designed and they are joined in the increasing order of radius with suitable conical shapes. The slope of the cones is adjusted experimentally. With this design, the return loss is simulated and found to be better than 20 dB upto 4.5 GHz and later it became poor. To overcome this difficulty, the abrupt transitions at the joints of the conical and cylindrical waveguides are made smoothen by increasing the diameter of one mouth of the cylinder and reducing the other mouth to match with the cylinders corresponding to next higher and lower frequency respectively. As a result, a smooth flared antenna is obtained and the simulated results are satisfactory. A parabolic reflector of 4 m diameter is designed and the smooth multi-flared antenna is kept at the

  16. Diversity and MIMO Performance Evaluation of Common Phase Center Multi Element Antenna Systems

    Directory of Open Access Journals (Sweden)

    V. Papamichael

    2008-06-01

    Full Text Available The diversity and Multiple Input Multiple Output (MIMO performance provided by common phase center multi element antenna (CPCMEA systems is evaluated using two practical methods which make use of the realized active element antenna patterns. These patterns include both the impact of the mutual coupling and the mismatch power loss at antenna ports. As a case study, two and four printed Inverted F Antenna (IFA systems are evaluated by means of Effective Diversity Gain (EDG and Capacity (C. EDG is measured in terms of the signal-to-noise ratio (SNR enhancement at a specific outage probability and in terms of the SNR reduction for achieving a desired average bit error rate (BER. The concept of receive antenna selection in MIMO systems is also investigated and the simulation results show a 43% improvement in the 1% outage C of a reconfigurable 2x2 MIMO system over a fixed 2x2 one.

  17. Low-Cost Phased Array Antenna for Sounding Rockets, Missiles, and Expendable Launch Vehicles

    Science.gov (United States)

    Mullinix, Daniel; Hall, Kenneth; Smith, Bruce; Corbin, Brian

    2012-01-01

    A low-cost beamformer phased array antenna has been developed for expendable launch vehicles, rockets, and missiles. It utilizes a conformal array antenna of ring or individual radiators (design varies depending on application) that is designed to be fed by the recently developed hybrid electrical/mechanical (vendor-supplied) phased array beamformer. The combination of these new array antennas and the hybrid beamformer results in a conformal phased array antenna that has significantly higher gain than traditional omni antennas, and costs an order of magnitude or more less than traditional phased array designs. Existing omnidirectional antennas for sounding rockets, missiles, and expendable launch vehicles (ELVs) do not have sufficient gain to support the required communication data rates via the space network. Missiles and smaller ELVs are often stabilized in flight by a fast (i.e. 4 Hz) roll rate. This fast roll rate, combined with vehicle attitude changes, greatly increases the complexity of the high-gain antenna beam-tracking problem. Phased arrays for larger ELVs with roll control are prohibitively expensive. Prior techniques involved a traditional fully electronic phased array solution, combined with highly complex and very fast inertial measurement unit phased array beamformers. The functional operation of this phased array is substantially different from traditional phased arrays in that it uses a hybrid electrical/mechanical beamformer that creates the relative time delays for steering the antenna beam via a small physical movement of variable delay lines. This movement is controlled via an innovative antenna control unit that accesses an internal measurement unit for vehicle attitude information, computes a beam-pointing angle to the target, then points the beam via a stepper motor controller. The stepper motor on the beamformer controls the beamformer variable delay lines that apply the appropriate time delays to the individual array elements to properly

  18. Capture Scheme of the Antenna in Ka-band for Launch Vehicle Based on Tracking and Data Relay Satellite%运载火箭Ka频段天基测控的天线捕获方法

    Institute of Scientific and Technical Information of China (English)

    宫长辉; 曾贵明; 张恒

    2011-01-01

    In order to transmit the space-based signal, the capture and track between the tracking and data relay satellite(TDRS) antenna and the user's aerocraft antenna should be completed firstly. In this paper, the uncertain area of the antenna scan is analyzed, adopting antenna-scan capture scheme for capturing the antenna on TORS by the phased-array antenna on launch vehicle. The values of the antenna array and EIRP are conformed and the capture time is given by computer simulation.%为实现天基信息的传输,首先要完成中继卫星天线与用户飞行器天线之间的捕获与跟踪.针对箭载相控阵天线对中继卫星的捕获,采用Ka频段相控阵天线扫描捕获策略,分析了天线扫描的不确定区域,确定了天线阵元数及EIRP值,给出了捕获时间的仿真结果,为工程应用提供参考.

  19. Phase calibration of the EISCAT Svalbard Radar interferometer using optical satellite signatures

    Directory of Open Access Journals (Sweden)

    J. M. Sullivan

    2006-09-01

    Full Text Available The link between natural ion-line enhancements in radar spectra and auroral activity has been the subject of recent studies but conclusions have been limited by the spatial and temporal resolution previously available. The next challenge is to use shorter sub-second integration times in combination with interferometric programmes to resolve spatial structure within the main radar beam, and so relate enhanced filaments to individual auroral rays. This paper presents initial studies of a technique, using optical and spectral satellite signatures, to calibrate the received phase of a signal with the position of the scattering source along the interferometric baseline of the EISCAT Svalbard Radar. It is shown that a consistent relationship can be found only if the satellite passage through the phase fringes is adjusted from the passage predicted by optical tracking. This required adjustment is interpreted as being due to the vector between the theoretical focusing points of the two antennae, i.e. the true radar baseline, differing from the baseline obtained by survey between the antenna foot points. A method to obtain a measurement of the true interferometric baseline using multiple satellite passes is outlined.

  20. Frequency Tunable Antennas and Novel Phased Array Feeding Networks for Next Generation Communication Systems

    OpenAIRE

    Avser, Bilgehan

    2015-01-01

    The thesis presents three dual-band frequency tunable antennas for carrier aggregation systems and two new feeding networks for reducing the number of phase shifters in limited-scan arrays. First, single- and dual-feed, dual-frequency, low-profile antennas with independent frequency tuning using varactor diodes are presented. The dual-feed planar inverted F-antenna (PIFA) has two operating frequencies which are independently tuned at 0.7--1.1 GHz and at 1.7--2.3 GHz with better than −10 dB im...

  1. An Algorithm to Calculate Phase-Center Offset of Aperture Antennas when Measuring 2-Dimensional Radiation Patterns

    Science.gov (United States)

    2015-01-01

    An Algorithm to Calculate Phase-Center Offset of Aperture Antennas when Measuring 2-Dimensional Radiation Patterns by Patrick Debroux...Offset of Aperture Antennas when Measuring 2-Dimensional Radiation Patterns Patrick Debroux and Berenice Verdin Survivability/Lethality Analysis... Antennas when Measuring 2-Dimensional Radiation Patterns 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S

  2. 8×8 Planar Phased Array Antenna with High Efficiency and Insensitivity Properties for 5G Mobile Base Stations

    DEFF Research Database (Denmark)

    Ojaroudiparchin, Naser; Shen, Ming; Pedersen, Gert F.

    2016-01-01

    An insensitive planar phased array antenna with high efficiency function for 5G applications is introduced in this study. 64-elements of compact slot-loop antenna elements have been used to form the 8×8 planar array. The antenna is designed on a low cost FR4 substrate and has good performance...

  3. Smart antennas

    CERN Document Server

    Godara, Lal Chand

    2004-01-01

    INTRODUCTION Antenna GainPhased Array AntennaPower Pattern Beam Steering Degree of Freedom Optimal AntennaAdaptive AntennaSmart AntennaSummary NARROWBAND PROCESSINGSignal Model Conventional BeamformerNull Steering BeamformerOptimal BeamformerOptimization Using Reference SignalBeam Space Processing Effect of ErrorsNotation and AbbreviationsReferencesADAPTIVE PROCESSINGSample Matrix Inversion AlgorithmUnconstrained Least Mean Squares AlgorithmNormalized Least Mean Squares AlgorithmConstrained

  4. Controlling the near-field excitation of nano-antennas with phase-change materials

    OpenAIRE

    2013-01-01

    By utilizing the strongly induced plasmon coupling between discrete nano-antennas and quantitatively controlling the crystalline proportions of an underlying Ge2Sb2Te5 (GST) phase-change thin layer, we show that nanoscale light localizations in the immediate proximity of plasmonic nano-antennas can be spatially positioned. Isolated energy hot-spots at a subwavelength scale can be created and adjusted across the landscape of the plasmonic system at a step resolution of λ/20. These findings int...

  5. A Broadband Conformal Phased Array Antenna on Spherical Surface

    Directory of Open Access Journals (Sweden)

    Dan Sun

    2014-01-01

    Full Text Available A Ku-band wideband conformal array antenna with 13×19 elements is presented in the paper. The array has a spherical structure, and its element is a proximity-coupled stacked patches antenna with a cavity-backed ground plane. The stacked patches and the cavity produce multiple coupled resonances, which enhance the bandwidth of the element extremely. A simulated model with the reasonable dimensions is framed with the coupling analyses, and the effective simulated results and good computing efficiency are obtained simultaneously. The measured results of the center embedded element in the whole array show a bandwidth exceeding 40% VSWR<2, which is close to the simulated matching performance.

  6. PHASIM, a sophisticated phased array antenna software simulator implemented in MATLAB 5.2

    NARCIS (Netherlands)

    Keizer, W.P.M.N.

    1999-01-01

    A sophisticated phased array simulator software package for the design and analysis of planar phased array antennas is presented. This simulator is coded in MATLAB version 5.2. Using MATLAB, numerical engineering problems can be solved in a fraction of time of time required by programs coded in FORT

  7. Mathematical Simulating Model of Phased-Array Antenna in Multifunction Array Radar

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    A mathematical simulating model of phased-array antenna in multifunction array radar has been approached in this paper, including the mathematical simulating model of plane phased-array pattern, the mathematical simulating model of directionality factor, the mathematical simulating model of array factor, the mathematical simulating model of array element factor and the mathematical simulating model of beam steering.

  8. PHASIM, a sophisticated phased array antenna software simulator implemented in MATLAB 5.2

    NARCIS (Netherlands)

    Keizer, W.P.M.N.

    1999-01-01

    A sophisticated phased array simulator software package for the design and analysis of planar phased array antennas is presented. This simulator is coded in MATLAB version 5.2. Using MATLAB, numerical engineering problems can be solved in a fraction of time of time required by programs coded in FORT

  9. Integrated filtering in reconfigurable planar phased-array antennas with spurious harmonic suppression

    NARCIS (Netherlands)

    Cifola, L.; Gerini, G.; Monni, S.; Berg, S. van den; Water, F. van de

    2013-01-01

    In the present work, the possibility to integrate filtering functionalities in a phased-array antenna at radiating element level is investigated. The filtenna concept has been applied to an X-band phased array of slot-fed patches. An effective strategy for the suppression of spurious harmonics, base

  10. An Optimal Beamforming Algorithm for Phased-Array Antennas Used in Multi-Beam Spaceborne Radiometers

    DEFF Research Database (Denmark)

    Iupikov, O. A.; Ivashina, M. V.; Pontoppidan, K.

    2015-01-01

    Strict requirements for future spaceborne ocean missions using multi-beam radiometers call for new antenna technologies, such as digital beamforming phased arrays. In this paper, we present an optimal beamforming algorithm for phased-array antenna systems designed to operate as focal plane arrays...... (FPA) in push-broom radiometers. This algorithm is formulated as an optimization procedure that maximizes the beam efficiency, while minimizing the side-lobe and cross-polarization power in the area of Earth, subject to a constraint on the beamformer dynamic range. The proposed algorithm is applied...

  11. Optical phase-locked loop signal sources for phased-array communications antennas

    Science.gov (United States)

    Langley, Lloyd N.; Edge, Colin; Wale, Michael J.; Gliese, Ulrik B.; Seeds, Alwyn J.; Walton, Channing; Wright, James G.; Coryell, Louis A.

    1997-10-01

    A coherent, optical heterodyne approach to signal generation and beamforming is particularly advantageous in multi-beam mobile phased arrays. Use of optical technology allows an optimum distribution of weight and power to be achieved between the antenna face and central electronics, together with an efficient implementation of the beamforming function and a modular design approach in which the basic building blocks are frequency-independent. Systems of this type employ a pair of optical carriers with a difference frequency equal to the required microwave signal. Phased- locking is necessary in order to achieve sufficiently low phase noise in the radio communication link. Optical phase locked loops (OPLLs) have been shown to be potential candidates for this application, yet work still needs to be done to bring them from the laboratory to field demonstrations. This paper describes the construction of a laser-diode OPLL subsystem for evaluation in a proof-of- concept beamforming system. This involves optimization of the loop design, development of single-frequency laser diodes with the correct linewidth, modulation and tuning characteristics and integration into a micro-optic assembly with custom wideband electronics.

  12. EQUIVALENT BASELINE AND INTERFEROMETRIC PHASE OF CLUSTER SATELLITE SAR

    Institute of Scientific and Technical Information of China (English)

    Gong Min; Zhang Chuanwu; Huang Shunji

    2005-01-01

    The change of the equivalent baseline and interferometric phase of cluster SAR satellites is analyzed when the constellation circles around the Earth and the satellites rotate around the center at the same time. The letter provides assessment of baseline error and phase error which influence the precision of height measurement in the across-track interferometric mode. The mathematical model of cluster satellite movement is built, simulation analyses and the curve of height error are presented. The simulation results show that height measurement error can be compensated by the formulae derived in this letter, therefore, the Digital Elevation Models (DEM's) are recovered accurately.

  13. Covariance analysis and phase ambiguity resolution for a linear interferometer antenna array

    Science.gov (United States)

    Johnson, James Andrew

    This thesis explores the application of mathematical techniques for estimating the angle of arrival (AOA) using a receiving platform having a linear interferometer antenna array. It addresses the estimation accuracy of interferometer phase measurements of a signal with superposed Gaussian noise from multiple antenna baselines, and provides a method for resolving the modulo two-pi problem inherent to many phase measurement systems. The study extends prior theoretical work (Hanna, C., 1983) by laying a mathematical foundation to complement his geometrical approach, provides a robust method of performance prediction for such a system. Key elements include estimation accuracy of a signal parameter with additive noise; the design of the linear antenna array element spacings and the relationship to Diophantine equations; and the application of the Cramer-Rao lower bound on variance of parameter estimation. It is hoped that the work presented here will serve as a practical guide for research scientists and engineers.

  14. Geolocation of Source Interference from a Single Satellite with Multiple Antennas

    Science.gov (United States)

    2014-03-01

    Systems ............................................................................ 124 a. INMARSAT Global Xpress ...7 Figure 4. Ku Band Single Antenna Footprint (from [12]). ............................................. 8 Figure 5. INMARSAT Global Xpress ...this sort of antenna system. This image is from INMARSAT’s planned Global Xpress system. Shown is the expected coverage provided by three Global

  15. Determination of the Phase Centers of Millimeter-Wave Horn Antennas Using a Holographic Interference Technique

    Science.gov (United States)

    McAuley, Ian; Murphy, J. Anthony; McCarthy, Darragh; Gradziel, Marcin; Mahon, Ronan; O'Sullivan, Creidhe; Trappe, Neil

    2016-04-01

    In this paper, we discuss how a holographic interference technique can be applied in the experimental determination of the phase centers of non-standard horn antennas in the millimeter-waveband. The phase center is the point inside the horn from which the radiation appears to emanate when viewed from the far-field, and knowing its location is necessary for optimizing coupling efficiencies to quasi-optical systems. For non-standard horn designs, and other feed structures, the phase center may be difficult to reliably predict by simulation, in which case, before committing to antenna manufacture, there is a requirement for it to be determined experimentally. Although the phase center can be recovered by direct phase measurement of the far-field beam pattern, this usually involves expensive instrumentation such as a vector network analyzer for millimeter wave horn antennas. In this paper, we describe one inexpensive alternative, which is based on measuring the interference pattern in intensity between the radiation from the horn of interest and a reference beam derived from the same coherent source in an off-axis holography setup. The accuracy of the approach is improved by comparison with the interference pattern of a well-understood standard horn (such as a corrugated conical horn) in the same experimental setup. We present an example of the technique applied to a profiled smooth-walled horn antenna, which has been especially designed for cosmic microwave background (CMB) polarization experiments.

  16. Design and characterisation of a phased antenna array for intact breast hyperthermia.

    Science.gov (United States)

    Curto, Sergio; Garcia-Miquel, Aleix; Suh, Minyoung; Vidal, Neus; Lopez-Villegas, Jose M; Prakash, Punit

    2017-06-28

    Currently available hyperthermia technology is not well suited to treating cancer malignancies in the intact breast. This study investigates a microwave applicator incorporating multiple patch antennas, with the goal of facilitating controllable power deposition profiles for treating lesions at diverse locations within the intact breast. A 3D-computational model was implemented to assess power deposition profiles with 915 MHz applicators incorporating a hemispheric groundplane and configurations of 2, 4, 8, 12, 16 and 20 antennas. Hemispheric breast models of 90 mm and 150 mm diameter were considered, where cuboid target volumes of 10 mm edge length (1 cm(3)) and 30 mm edge length (27 cm(3)) were positioned at the centre of the breast, and also located 15 mm from the chest wall. The average power absorption (αPA) ratio expressed as the ratio of the PA in the target volume and in the full breast was evaluated. A 4-antenna proof-of-concept array was fabricated and experimentally evaluated. Computational models identified an optimal inter-antenna spacing of 22.5° along the applicator circumference. Applicators with 8 and 12 antennas excited with constant phase presented the highest αPA at centrally located and deep-seated targets, respectively. Experimental measurements with a 4-antenna proof-of-concept array illustrated the potential for electrically steering power deposition profiles by adjusting the relative phase of the signal at antenna inputs. Computational models and experimental results suggest that the proposed applicator may have potential for delivering conformal thermal therapy in the intact breast.

  17. Performance Analysis of Anti-Interference Wireless Packet Networks for LEO Micro-Satellite with Adaptive Nulling Antenna Array

    Institute of Scientific and Technical Information of China (English)

    LIU Hai-tao; HAN Fang-jing; WAN Jian-wei

    2006-01-01

    Information integrity is key to successful operations in intricacy environments in the future, especially when strong interferences exist. This paper presents the design of a novel wireless packet network receiver system for Low Earth Orbit (LEO) micro-satellites with adaptive nulling antenna arrays. It uses three types of interference suppression in cascade: namely spread spectrum, adaptive array nulling, and transform domain filtering. This paper proposes a pilot channel-aided method in order to make full advantage of this arrangement, and analyzes its throughput and delay performance using the Markov chain model. Our results show that this method can achieve excellent delay and throughput performance: When the number of array antenna is 8, its throughput increase relative to the standard Slot-ALOHA protocol is 125 %.

  18. 星载多波束天线设计%Design of Multi-beam Satellite Antennas

    Institute of Scientific and Technical Information of China (English)

    段玉虎

    2011-01-01

    给出了星栽多波束天线的设计方法、步骤和参数选择原则,给出了2个区域多点波束天线和赋形波束的设计实例,并用物理光学法计算了覆盖区域的天线方向图、覆盖区增益和频率复用时的同极化波束隔离.%The design method, procedure and principle of parameter choice for design of multi-beam satellite antennas are presented. Furthermore, the paper offers specific design examples of two-region multi-beam antennas and shaped beam. Finally, the radiation pattern and co-polarization isolation against gain and with frequency reuse of coverage area are calculated with physical-optics method.

  19. An Error Analysis of the Phased Array Antenna Pointing Algorithm for STARS Flight Demonstration No. 2

    Science.gov (United States)

    Carney, Michael P.; Simpson, James C.

    2005-01-01

    STARS is a multicenter NASA project to determine the feasibility of using space-based assets, such as the Tracking and Data Relay Satellite System (TDRSS) and Global Positioning System (GPS), to increase flexibility (e.g. increase the number of possible launch locations and manage simultaneous operations) and to reduce operational costs by decreasing the need for ground-based range assets and infrastructure. The STARS project includes two major systems: the Range Safety and Range User systems. The latter system uses broadband communications (125 kbps to 500 kbps) for voice, video, and vehicle/payload data. Flight Demonstration #1 revealed the need to increase the data rate of the Range User system. During Flight Demo #2, a Ku-band antenna will generate a higher data rate and will be designed with an embedded pointing algorithm to guarantee that the antenna is pointed directly at TDRS. This algorithm will utilize the onboard position and attitude data to point the antenna to TDRS within a 2-degree full-angle beamwidth. This report investigates how errors in aircraft position and attitude, along with errors in satellite position, propagate into the overall pointing vector.

  20. Nonlinear analysis and vibration suppression control for a rigid-flexible coupling satellite antenna system composed of laminated shell reflector

    Science.gov (United States)

    You, Bin Di; Wen, Jian Min; Zhao, Yang

    2014-03-01

    In this paper, a nonlinear dynamic modeling method for a rigid-flexible coupling satellite antenna system composed of laminated shell reflector is proposed undergoing a large overall motion. For the study of the characteristics of the reflector using laminated shell structure, the displacement field description of a point in a 3-noded shell element is acquired in conjunction with the length stretch, lateral bending and torsional deformation. Hence, a nonlinear dynamic model of the satellite antenna system is deduced based on Lagrange's equations. The complete expressions of nonlinear terms of elastic deformation and coupling terms between rigid motion and large deflection are considered in the dynamic equations, and the dynamic behavior of the rigid-flexible coupling system is analyzed using linear model and nonlinear model, respectively. In order to eliminate the system vibration, the PD with vibration force feedback control strategy is used to achieve its desired angles and velocity in a much shorter duration, and can further accomplish reduction of residual vibration. Then, the asymptotic stability of the system is proved based on the Lyapunov method. Through numerical computation, the results show that the linear model cannot capture the motion-induced coupling terms and geometric nonlinearity variations. However, the nonlinear model is suitable for dealing with large deformation rigid-flexible problem undergoing large overall motions. Hence, the satellite antenna pointing accuracy would be predicted based on the nonlinear model. Furthermore, the results also show that the proposed control strategy can suppress system vibration quickly. The above conclusions would have important academic significance and engineering value.

  1. Controlling the near-field excitation of nano-antennas with phase-change materials

    Directory of Open Access Journals (Sweden)

    Tsung Sheng Kao

    2013-10-01

    Full Text Available By utilizing the strongly induced plasmon coupling between discrete nano-antennas and quantitatively controlling the crystalline proportions of an underlying Ge2Sb2Te5 (GST phase-change thin layer, we show that nanoscale light localizations in the immediate proximity of plasmonic nano-antennas can be spatially positioned. Isolated energy hot-spots at a subwavelength scale can be created and adjusted across the landscape of the plasmonic system at a step resolution of λ/20. These findings introduce a new approach for nano-circuitry, bio-assay addressing and imaging applications.

  2. Controlling the near-field excitation of nano-antennas with phase-change materials.

    Science.gov (United States)

    Kao, Tsung Sheng; Chen, Yi Guo; Hong, Ming Hui

    2013-01-01

    By utilizing the strongly induced plasmon coupling between discrete nano-antennas and quantitatively controlling the crystalline proportions of an underlying Ge2Sb2Te5 (GST) phase-change thin layer, we show that nanoscale light localizations in the immediate proximity of plasmonic nano-antennas can be spatially positioned. Isolated energy hot-spots at a subwavelength scale can be created and adjusted across the landscape of the plasmonic system at a step resolution of λ/20. These findings introduce a new approach for nano-circuitry, bio-assay addressing and imaging applications.

  3. Analysis of Circularly Polarized Hemispheroidal Dielectric Resonator Antenna Phased Arrays Using the Method of Auxiliary Sources

    DEFF Research Database (Denmark)

    Larsen, Niels Vesterdal; Breinbjerg, Olav

    2007-01-01

    The method of auxiliary sources is employed to model and analyze probe-fed hemispheroidal dielectric resonator antennas and arrays. Circularly polarized antenna elements of different designs are analyzed, and impedance bandwidths of up to 14.7% are achieved. Selected element designs are subsequen...... are subsequently employed in a seven-element phased array. The array performance is analyzed with respect to scan loss and main beam directivity as a function of scan angle and frequency, and the influence of element separation is investigated....

  4. Symbol-Level Precoding with Per-antenna Power Constraints for the Multi-beam Satellite Downlink

    OpenAIRE

    Spano, Danilo; Chatzinotas, Symeon; Krause, Jens; Ottersten, Björn

    2016-01-01

    This paper tackles the problem of multi-user interference in the forward downlink channel of a multi-beam satellite system. A symbol-level precoding scheme is considered, where the data information is used, along with the channel state information, in order to exploit the multi-user interference and transform it into useful power at the receiver side. In this framework, the max-min fair problem for constructive interference is formulated and solved, under per-antenna power constraints. The co...

  5. Waveguide Slot Array Antenna with a Hybrid-Phase Feed for Grating Lobe Reduction

    Directory of Open Access Journals (Sweden)

    Son Trinh-Van

    2016-01-01

    Full Text Available The design of a 112-element millimeter-wave waveguide slot array antenna to reduce the grating lobe level is presented. A hybrid-phase feeding technique combining a cophase feed and an alternating-phase feed is applied to facilitate the suppression of grating lobes. In addition, a stepped feed waveguide and offset coupling slots aligned in a line are employed to realize a tapered aperture distribution. As a result, grating lobe suppression of 8.1 dB was achieved on the diagonal planes compared to a conventional alternating-phase-fed waveguide slot array antenna. A prototype of the proposed antenna was fabricated and measured. The measured results show that the proposed antenna exhibits a −15 dB reflection bandwidth of 3.4% and an average realized gain of 26.72 dBi within the measured frequency range. Good agreement between the simulated and measured radiation patterns is also observed.

  6. Design of an optically controlled Ka-band GaAs MMIC phased-array antenna

    Science.gov (United States)

    Kunath, Richard R.; Bhasin, Kul B.; Claspy, Paul C.; Richard, Mark A.

    1990-06-01

    Phased array antennas long were investigated to support the agile, multibeam radiating apertures with rapid reconfigurability needs of radar and communications. With the development of the Monolithic Microwave Integrated Circuit (MMIC), phased array antennas having the stated characteristics are becoming realizable. However, at K-band frequencies (20 to 40 GHz) and higher, the problem of controlling the MMICs using conventional techniques either severely limits the array size or becomes insurmountable due to the close spacing of the radiating elements necessary to achieve the desired antenna performance. Investigations were made that indicate using fiber optics as a transmission line for control information for the MMICs provides a potential solution. By adding an optical interface circuit to pre-existing MMIC designs, it is possible to take advantage of the small size, lightweight, mechanical flexibility and RFI/EMI resistant characteristics of fiber optics to distribute MMIC control signals. The architecture, circuit development, testing and integration of optically controlled K-band MMIC phased array antennas are described.

  7. Design of an optically controlled Ka-band GaAs MMIC phased-array antenna

    Science.gov (United States)

    Kunath, Richard R.; Bhasin, Kul B.; Claspy, Paul C.; Richard, Mark A.

    1990-01-01

    Phased array antennas long were investigated to support the agile, multibeam radiating apertures with rapid reconfigurability needs of radar and communications. With the development of the Monolithic Microwave Integrated Circuit (MMIC), phased array antennas having the stated characteristics are becoming realizable. However, at K-band frequencies (20 to 40 GHz) and higher, the problem of controlling the MMICs using conventional techniques either severely limits the array size or becomes insurmountable due to the close spacing of the radiating elements necessary to achieve the desired antenna performance. Investigations were made that indicate using fiber optics as a transmission line for control information for the MMICs provides a potential solution. By adding an optical interface circuit to pre-existing MMIC designs, it is possible to take advantage of the small size, lightweight, mechanical flexibility and RFI/EMI resistant characteristics of fiber optics to distribute MMIC control signals. The architecture, circuit development, testing and integration of optically controlled K-band MMIC phased array antennas are described.

  8. Phase-compensated metasurface for a conformal microwave antenna

    Science.gov (United States)

    Germain, Dylan; Seetharamdoo, Divitha; Nawaz Burokur, Shah; de Lustrac, André

    2013-09-01

    The in-phase radiation from a conformal metamaterial surface is numerically and experimentally reported. The LC-resonant metasurface is composed of a simultaneously capacitive and an inductive grid constituted by copper strips printed on both sides of a dielectric board. The metasurface is designed to fit a curved surface by modifying its local phase. The latter phase-compensated metasurface is used as a reflector in a conformal Fabry-Pérot resonant cavity designed to operate at microwave frequencies. Far-field measurements performed on a fabricated prototype allow showing the good performances of such a phase-compensated metasurface in restoring in-phase emissions from the conformal surface and producing a directive emission in the desired direction.

  9. The Hitachi and Takahagi 32 m radio telescopes: Upgrade of the antennas from satellite communication to radio astronomy

    Science.gov (United States)

    Yonekura, Yoshinori; Saito, Yu; Sugiyama, Koichiro; Soon, Kang Lou; Momose, Munetake; Yokosawa, Masayoshi; Ogawa, Hideo; Kimura, Kimihiro; Abe, Yasuhiro; Nishimura, Atsushi; Hasegawa, Yutaka; Fujisawa, Kenta; Ohyama, Tomoaki; Kono, Yusuke; Miyamoto, Yusuke; Sawada-Satoh, Satoko; Kobayashi, Hideyuki; Kawaguchi, Noriyuki; Honma, Mareki; Shibata, Katsunori M.; Sato, Katsuhisa; Ueno, Yuji; Jike, Takaaki; Tamura, Yoshiaki; Hirota, Tomoya; Miyazaki, Atsushi; Niinuma, Kotaro; Sorai, Kazuo; Takaba, Hiroshi; Hachisuka, Kazuya; Kondo, Tetsuro; Sekido, Mamoru; Murata, Yasuhiro; Nakai, Naomasa; Omodaka, Toshihiro

    2016-10-01

    The Hitachi and Takahagi 32 m radio telescopes (former satellite communication antennas) were so upgraded as to work at 6, 8, and 22 GHz. We developed the receiver systems, IF systems, back-end systems (including samplers and recorders), and reference systems. We measured the performance of the antennas. The system temperature including the atmosphere toward the zenith, T_sys^{ast }, is measured to be ˜30-40 K for 6 GHz and ˜25-35 K for 8 GHz. T_sys^{ast } for 22 GHz is measured to be ˜40-100 K in winter and ˜150-500 K in summer seasons, respectively. The aperture efficiency is 55%-75% for Hitachi at 6 GHz and 8 GHz, and 55%-65% for Takahagi at 8 GHz. The beam sizes at 6 GHz and 8 GHz are ˜4.6° and ˜3.8°, respectively. The side-lobe level is less than 3%-4% at 6 and 8 GHz. Pointing accuracy was measured to be better than ˜0.3° for Hitachi and ˜0.6° for Takahagi. We succeeded in VLBI observations in 2010 August, indicating good performance of the antenna. We started single-dish monitoring observations of 6.7 GHz methanol maser sources in 2012 December, and found several new sources showing short-term periodic variation of the flux density.

  10. Controlling gradient phase distributions in a model of active antenna array with locally coupled elements

    Science.gov (United States)

    Mishagin, K. G.; Shalfeev, V. D.

    2006-12-01

    The regime of synchronization with a certain gradient phase distribution and the possibility of controlling such distribution in a linear array of oscillators coupled by phase-locked loops (PLLs) have been theoretically studied. It is shown that a constant phase progression can be controlled by manipulating collective dynamics, with oscillator eigenfrequencies and coupling coefficients being the control parameters. The proposed principle of control, based on the nonlinear dynamics of PLL-coupled oscillators, can be used in solving the problems of phasing and controlled beam scanning in antenna arrays operating in different frequency bands.

  11. Optoelectronic signal processing for phased-array antennas II; Proceedings of the Meeting, Los Angeles, CA, Jan. 16, 17, 1990

    Science.gov (United States)

    Hendrickson, Brian M.; Koepf, Gerhard A.

    Various papers on optoelectronic signal processing for phased-array antennas (PAAs) are presented. Individual topics addressed include: the dynamics of high-frequency lasers, an electrooptic phase modulator for PA applications, a laser mixer for microwave fiber optics, optical control of microwaves with III-V semiconductor optical waveguides, a high-dynamic-range modulator for microwave PAs, the high-modulation-rate potential of surface-emitter laser-diode arrays, an electrooptical switch for antenna beam steering, and adaptive PA radar processing using photorefractive crystals. Also discussed are an optical processor for array antenna beam shaping and steering, an integrated optical Butler matrix for beam forming in PAAs, an acoustooptic/photorefractive processor for adaptive antenna arrays, BER testing of fiber-optic data links for MMIC-based phased-array antennas, and the design of an optically controlled K(a)-band GaAs MMIC PAA.

  12. An L-Band, Circularly Polarised, Dual-Feed, Cavity-Backed Annular Slot Antenna For Phased-Array Applications

    DEFF Research Database (Denmark)

    Larsen, Niels Vesterdal; Breinbjerg, Olav

    2006-01-01

    The results of a parametric study for the development of an L-band, circularly polarised, dual-feed, cavity-backed annular slot antenna is presented. The study included detailed numerical simulations and measurements on a prototype with different ground planes, to assess the antenna’s applicability...... as an element in a small phased array antenna....

  13. Auxetic shape memory alloy cellular structures for deployable satellite antennas: design, manufacture and testing

    Directory of Open Access Journals (Sweden)

    Di Maio D.

    2010-06-01

    Full Text Available We describe the production development and experimental tests related to an hybrid honeycomb-truss made of shape memory alloy (Ni48Ti46Cu6, and used as a demonstrator for a deployable antenna in deep-space missions. Specific emphasis is placed on the modal analysis techniques used to test the lightweight SMA structure.

  14. Phase control system concepts and simulations. [solar power satellite system

    Science.gov (United States)

    Lindsay, V. C.

    1980-01-01

    A phase control system concept for a solar power satellite is proposed which partitions the system into three major levels. The first level of phase control consists of a reference phase distribution system implemented in the form of phase distribution tree structure. The major purpose of the tree structure is to electronically compensate for the phase shift due to the transition path lengths from the center of the spacetenna to each phase control center located in each subarray. In the reference system, this is accomplished using the master slave returnable timing system technique. The second level of phase control consists of the beam steering and microwave power generating system which houses the power transponders. This transponder consists of a set of phase conjugation multipliers driven by the reference phase distribution system output and the output of a pilot spread spectrum receiver which accepts the received pilot via a diplexer connected to a separate receive horn or the subarray itself. The output of the phase conjugation circuits serve as inputs to the third level of the phase control system. The third level of phase control is associated with maintaining an equal and constant phase shift through the microwave power amplifier devices while minimizing the associated phase noise effects on the generated power beam. This is accomplished by providing a phase locked loop around each high power amplifier.

  15. Beamforming Errors in Murchison Widefield Array Phased Array Antennas and their effects on Epoch of Reionization Science

    CERN Document Server

    Neben, A R; Bradley, R F; Dillon, J S; Bernardi, G; Bowman, J D; Briggs, F; Cappallo, R J; Corey, B E; Deshpande, A A; Goeke, R; Greenhill, L J; Hazelton, B J; Johnston-Hollitt, M; Kaplan, D L; Lonsdale, C J; McWhirter, S R; Mitchell, D A; Morales, M F; Morgan, E; Oberoi, D; Ord, S M; Prabu, T; Shankar, N Udaya; Srivani, K S; Subrahmanyan, R; Tingay, S J; Wayth, R B; Webster, R L; Williams, A; Williams, C L

    2016-01-01

    Accurate antenna beam models are critical for radio observations aiming to isolate the redshifted 21cm spectral line emission from the Dark Ages and the Epoch of Reionization and unlock the scientific potential of 21cm cosmology. Past work has focused on characterizing mean antenna beam models using either satellite signals or astronomical sources as calibrators, but antenna-to-antenna variation due to imperfect instrumentation has remained unexplored. We characterize this variation for the Murchison Widefield Array (MWA) through laboratory measurements and simulations, finding typical deviations of order +/- 10-20% near the edges of the main lobe and in the sidelobes. We consider the ramifications of these results for image- and power spectrum-based science. In particular, we simulate visibilities measured by a 100m baseline and find that using an otherwise perfect foreground model, unmodeled beamforming errors severely limit foreground subtraction accuracy within the region of Fourier space contaminated by ...

  16. 基于Simulink仿真的用户星天线控制系统分析%Analysis of Simulink-based antenna control system on user satellite

    Institute of Scientific and Technical Information of China (English)

    龙甲禄; 闫剑虹

    2012-01-01

    To meet the need of the antenna pointing accuracy of data relay satellite system, the antenna pointing control concept is described, and the establishment process of the link between the user satellite and data relay satellite is analyzed. A scheme for satelite-borne autonomous control is designed, A mathematic simulation of the antenna pointing control system is conducted under the Simulink circumstance. The tracking performance of the antenna control system on the user satellite is verified by the analysis of the simulation results.%为满足中继卫星系统对天线指向精度的要求,首先描述了天线指向控制概念,对用户星与中继卫星星间链路的建立过程进行了分析,并且设计了星上自主控制方案,在Simulink环境下对所设计的天线指向控制系统进行了数学仿真,最后通过对仿真结果的分析验证了用户星天线控制系统的跟踪性能.

  17. Feedback Control System for Antenna Phase Difference in the LHCD Experiments

    Institute of Scientific and Technical Information of China (English)

    Jiang Min; Kuang Guangli; Shan Jiafang; Lin Jian'an; Kong Jun; HT-7 Team

    2005-01-01

    It is well accepted that lower hybrid current drive (LHCD) is the most efficient method for non-inductive current drive in fusion devices and the effect of the current drive is dependent on not only microwave power but also its grill phase shift. This paper presents a new kind of feedback control system for antenna phase difference in LHCD experiments. In this high-speed control system, a lot of new technologies and methods are incorporated. The results of the experiments show a very good agreement with the system design.

  18. Beam-Switch Transient Effects in the RF Path of the ICAPA Receive Phased Array Antenna

    Science.gov (United States)

    Sands, O. Scott

    2003-01-01

    When the beam of a Phased Array Antenna (PAA) is switched from one pointing direction to another, transient effects in the RF path of the antenna are observed. Testing described in the report has revealed implementation-specific transient effects in the RF channel that are associated with digital clocking pulses that occur with transfer of data from the Beam Steering Controller (BSC) to the digital electronics of the PAA under test. The testing described here provides an initial assessment of the beam-switch phenomena by digitally acquiring time series of the RF communications channel, under CW excitation, during the period of time that the beam switch transient occurs. Effects are analyzed using time-frequency distributions and instantaneous frequency estimation techniques. The results of tests conducted with CW excitation supports further Bit-Error-Rate (BER) testing of the PAA communication channel.

  19. Lithium niobate guided-wave beam former for steering phased-array antennas.

    Science.gov (United States)

    Armenise, M N; Passaro, V M; Noviello, G

    1994-09-10

    We present the theoretical investigation, design, and simulation of a novel guided-wave optical processor for L-band-transmission beam forming in a linear array of phased active antennas. The proposed configuration includes two contradirectional surface acoustic-wave transducers, and it is based on a Y-cut, X-propagating Ti:LiNbO(3) planar waveguide supporting the lowest-order modes of both polarizations (TE(0) and TM(0)) at the free-space wavelength λ = 0.85 µm. A detailed comparison between the processor we propose and other optical and electronic architectures reported in the literature is carried out, exhibiting a number of significant advantages in terms of weight, total chip size, and power consumption, when the number of antenna elements is greater than 50.

  20. System-level integrated circuit (SLIC) development for phased array antenna applications

    Science.gov (United States)

    Shalkhauser, K. A.; Raquet, C. A.

    1991-01-01

    A microwave/millimeter wave system-level integrated circuit (SLIC) being developed for use in phased array antenna applications is described. The program goal is to design, fabricate, test, and deliver an advanced integrated circuit that merges radio frequency (RF) monolithic microwave integrated circuit (MMIC) technologies with digital, photonic, and analog circuitry that provide control, support, and interface functions. As a whole, the SLIC will offer improvements in RF device performance, uniformity, and stability while enabling accurate, rapid, repeatable control of the RF signal. Furthermore, the SLIC program addresses issues relating to insertion of solid state devices into antenna systems, such as the reduction in number of bias, control, and signal lines. Program goals, approach, and status are discussed.

  1. Calibration and performance analysis on channel mismatch of multi-beam antenna on satellites%星载多波束天线通道误差特性分析及校准

    Institute of Scientific and Technical Information of China (English)

    赵星惟; 龚文斌; 梁旭文

    2012-01-01

    针对星载多波束天线幅相误差对天线性能影响较大的问题,通过对多波束发射天线的射频通道在不同温度下的幅相特性进行试验测定,得到了通道幅相特性与温度的对应关系,发现不同通道的幅相特性与通道温度的关系曲线在给定温度区间内基本呈线性关系,且斜率基本一致,从而确定了对不同通道的幅相特性进行固定值补偿的校准策略.通过固定值补偿后,各通道的幅相特性曲线基本重合,从而消除了通道间幅相误差.进一步给出了提升温度一致性的措施,并设计了多波束发射天线的校准原理框图和校准流程图.结果表明:新的星载多波束天线幅相误差校准方法是有效的.%To solve the mismatch effect of amplitude-and-phase errors on multi-beam antenna performance , the radio frequency channel amplitude and phase errors of multi-beam transmitting antenna on satellite were experimentally measured to obtain the corresponding relations of channel amplitude-and-phase mismatch and temperature, and to compensate the mismatch. The shell temperatures are almost same after temperature stabilization, which effectively results in channel consistency. Some methods were used to improve temperature consistency. Calibration of channel is the key to guarantee the performance indexes of multi-beam antenna on satellites. The calibration principle block diagram and flow chart of multi-beam transmitting antenna were designed. The theoretical analysis and simulation results show that the proposed calibration method is effective for calibration of multi-beam antenna on satellites.

  2. Development of Spaceborne Deployable Active Phased Array Antennas%星载可展开有源相控阵天线结构的研究进展

    Institute of Scientific and Technical Information of China (English)

    王从思; 韩如冰; 王伟; 王猛; TU Qingsong; 平丽浩

    2016-01-01

    星载可展开有源相控阵天线作为空间通信、电子侦察、导航、环境监测等卫星系统的“眼睛”和“耳朵”,通过空间可展开结构实现较大的物理口径,利用有源相控阵体制实现独立控制多个点波束,克服了传统机械扫描天线的诸多缺点,已成为宇航领域的关键装备之一。总结星载有源相控阵天线发展历程,分析星载有源相控阵天线的结构形式、性能要求及应用情况,阐述国内外研究现状,并对其涉及的七项关键结构技术做了概要解析,探讨星载可展开有源相控阵天线结构领域的未来研究方向。%As the“eyes” and “ears” of the space communications, electronic countermeasures, navigation, environmental monitoring and other satellite systems, the spaceborne deployable active phased array antenna achieves a greater physical aperture through a deployable configuration, and implements the individual control of different spot beams using the electronic scan mode. It has been one of the key equipments in the areas of aerospace without the many drawbacks brought by the mechanical scan antennas. The development process of the spaceborne active phased array antennas is introduced. And the configuration styles, performance requirements and engineering applications of the spaceborne deployable active phased array antennas are presented. The international research statuses are described. At the same time, a concise analysis of the seven key technologies of antenna structure field is made. The develop trends of the spaceborne deployable active phased array antenna structural technologies are discussed.

  3. Microstrip Array Antenna with 16 Patches for UHF Band Television Signal Reception

    Directory of Open Access Journals (Sweden)

    Yulindon Yulindon

    2013-01-01

    Full Text Available There are 2 commonly known equipment for the reception of television broadcasts i.e. using a parabolic antenna connected to satellite receiver and a wire or pipe antenna that directly connected to the television receiver. Receiving the signal by means of a parabolic antenna is more expensive because it requires additional tools , namely satellite receivers, so generally the people like to choose the easier way by direct receiving the signal using wire antenna. The antenna construction which made of aluminum pipes has a weakness easily bent or broken on the assembling phase as well as when there are high winds causing the antenna mast collapsed, confirmed that the antenna is bent, loose or broken elements. The paper relates to a microstrip antenna for reception of television signals using material printed circuit boards or printed circuit board (PCB which is a thin but strong in the form of a number of patches array separated in a certain distance.

  4. Scanning beam antenna conceptual design for 20/30 GHz satellite systems

    Science.gov (United States)

    Smetana, J.; Sorbello, R.; Crosswell, W. F.

    1983-01-01

    The configuration described is one of four antenna system configurations developed using a variety of monolithic microwave integrated circuit module arrangements and optical systems. A parametric analysis is expected to produce a data base for the selection of design points for a variety of applications. Soon to be accomplished is the design concept of the active (lens) array, which will take into consideration such factors as, coupling effects, the space-fed power divider network design, input bias and control layout, investigation of thermal distribution, and analysis of module failure (graceful degradation).

  5. Digital-beamforming array antenna technologies for future ocean-observing satellite missions

    DEFF Research Database (Denmark)

    Iupikov, Oleg A.; Ivashina, Marianna V.; Cappellin, Cecilia

    2016-01-01

    Existing passive microwave radiometers that are used for ocean observations are limited in spatial resolution and geographic coverage, due to the limitations of traditional antenna technologies using mechanically-scanning reflectors and horn-type feeds. Future ocean observation missions call...... for new solutions, such as digitally-beamforming array feeds (DBAFs) as well as stationary and more complex reflectors. Our studies demonstrate that DBAFs can overcome the physically fundamental limitations of traditional horn feeds, and are capable of meeting all the challenging requirements for the next...

  6. A Tutorial on Optical Feeding of Millimeter-Wave Phased Array Antennas for Communication Applications

    Directory of Open Access Journals (Sweden)

    Ivan Aldaya

    2015-01-01

    Full Text Available Given the interference avoidance capacity, high gain, and dynamical reconfigurability, phased array antennas (PAAs have emerged as a key enabling technology for future broadband mobile applications. This is especially important at millimeter-wave (mm-wave frequencies, where the high power consumption and significant path loss impose serious range constraints. However, at mm-wave frequencies the phase and amplitude control of the feeding currents of the PAA elements is not a trivial issue because electrical beamforming requires bulky devices and exhibits relatively narrow bandwidth. In order to overcome these limitations, different optical beamforming architectures have been presented. In this paper we review the basic principles of phased arrays and identify the main challenges, that is, integration of high-speed photodetectors with antenna elements and the efficient optical control of both amplitude and phase of the feeding current. After presenting the most important solutions found in the literature, we analyze the impact of the different noise sources on the PAA performance, giving some guidelines for the design of optically fed PAAs.

  7. Study Of Phasing Distribution Characteristics Of Reflectarray Antenna Using Different Resonant Elements

    Directory of Open Access Journals (Sweden)

    M.Y. Ismail

    2009-12-01

    Full Text Available There has been much interest recently in developing reflectarray antenna due to the combination of some of the best features between the parabolic reflector and phased array antennas. This paper presents the study of the relationship between phasing distribution characteristics and the bandwidth of different resonant reflectarray elements. The gradient characteristics of different elements of patch, dipole and ring printed on a grounded dielectric substrate have been investigated at X-band frequency range using CST computer model. The preliminary simulated results generated from CST computer model demonstrate that ring elements contribute the highest reflection loss performance of 1.74 dB compared to the other two element of dipoles and patches. The attainable static linear phase range of 177o for ring elements is shown to offer a trade off between the static phase range and the bandwidth of the reflectarray elements. In measurement ring element also contribute the highest reflection loss performance of 2.95 dB compared to other two elements.

  8. Frequency Tunable Antennas and Novel Phased Array Feeding Networks for Next Generation Communication Systems

    Science.gov (United States)

    Avser, Bilgehan

    The thesis presents three dual-band frequency tunable antennas for carrier aggregation systems and two new feeding networks for reducing the number of phase shifters in limited-scan arrays. First, single- and dual-feed, dual-frequency, low-profile antennas with independent frequency tuning using varactor diodes are presented. The dual-feed planar inverted F-antenna (PIFA) has two operating frequencies which are independently tuned at 0.7--1.1 GHz and at 1.7--2.3 GHz with better than 10 dB impedance match. The isolation between the high-band and the low-band ports is > 13 dB; hence, one resonant frequency can be tuned without affecting the other. The single-feed contiguous-dual-band antenna has two resonant frequencies, which are independently tuned at 1.2--1.6 GHz at 1.6--2.3 GHz with better than 10 dB impedance match for most of the tuning range. And the single-feed dual-band antenna has two resonant frequencies, which are independently tuned at 0.7--1.0 GHz at 1.7--2.3 GHz with better than 10 dB impedance match for most of the tuning range. The tuning is done using varactor diodes with a capacitance range from 0.8 to 3.8 pF, which is compatible with RF MEMS devices. The antenna volumes are 63 x 100 x 3.15 mm3 on epsilon r = 3.55 substrates and the measured antenna efficiencies vary between 25% and 50% over the tuning range. The application areas are in carrier aggregation systems for fourth generation (4G) wireless systems. Next, a new phased array feeding network that employs random sequences of non-uniform sub-arrays (and a single phase shifter for each sub-array) is presented. When these sequences are optimized, the resulting phased arrays can scan over a wide region with low sidelobe levels. Equations for analyzing the random arrays and an algorithm for optimizing the array sequences are presented. Multiple random-solutions with different number of phase shifters and different set of sub-array groups are analyzed and design guidelines are presented. The

  9. Beampattern for Multiple Antennas in Hybrid Terrestrial Satellite Communications System (HTSCS

    Directory of Open Access Journals (Sweden)

    Farman Ullah

    2013-10-01

    Full Text Available The hybrid architecture of Terrestrial and Satellite networks discussed in this paper utilizes frequency reuse. However, at the same time the frequency reuse results in Co-Channel Interference (CCI. The CCI is caused by the mobile users to the satellite end because of the strong receiver on the satellite end. Mainly, this paper will focus on to tone down the CCI and would also show that how the OFDM based adaptive beamforming can be employed to mitigate this interference. The technique which is being used to mitigate this interference is Pre-FFT adaptive beamforming also called as time domain beamforming. In this paper, main task is to mitigate the CCI which is induced by the mobile users to the satellite end and will be considered that there are J users. Out of these J users there is one desired user and rest are interferers. When the interfered data is received at the satellite end, the Pre-FFT adaptive beamforming extracts the desired user data from the interferers by applying the complex weights to the received symbol. The weight for the next symbol is then updated by Least Mean Square (LMS algorithm and then is applied to it. This process is carried out till all the desired user data is extracted from the interference signal.

  10. Hierarchical Phased Array Antenna Focal Plane for Cosmic Microwave Background Polarization and Sub-mm Observations

    Science.gov (United States)

    Lee, Adrian

    We propose to develop planar-antenna-coupled superconducting bolometer arrays for observations at sub-millimeter to millimeter wavelengths. Our pixel architecture features a dual-polarization, log-periodic antenna with a 5:1 bandwidth ratio, followed by a filter bank that divides the total bandwidth into several broad photometric bands. We propose to develop an hierarchical phased array of our basic pixel type that gives optimal mapping speed (sensitivity) over a much broader range of frequencies. The advantage of this combination of an intrinsically broadband pixel with hierarchical phase arraying include a combination of greatly reduced focal-plane mass, higher array sensitivity, and a larger number of spectral bands compared to focal-plane designs using conventional single-color pixels. These advantages have the potential to greatly reduce cost and/or increase performance of NASA missions in the sub-millimeter to millimeter bands. For CMB polarization, a wide frequency range of about 30 to 400 GHz is required to subtract galactic foregrounds. As an example, the multichroic architecture we propose could reduce the focal plane mass of the EPIC-IM CMB polarization mission study concept by a factor of 4, with great savings in required cryocooler performance and therefore cost. We have demonstrated the lens-coupled antenna concept in the POLARBEAR groundbased CMB polarization experiment which is now operating in Chile. That experiment uses a single-band planar antenna that gives excellent beam properties and optical efficiency. POLARBEAR recently succeeded in detecting gravitational lensing B-modes in the CMB polarization. In the laboratory, we have measured two octaves of total bandwidth in the log-periodic sinuous antenna. We have built filter banks of 2, 3, and 7 bands with 4, 6, and 14 bolometers per pixel for two linear polarizations. Pixels of this type are slated to be deployed on the ground in POLARBEAR and SPT-3G and proposed to be used on a balloon by EBEX

  11. Measuring Noise Temperatures of Phased-Array Antennas for Astronomy at CSIRO

    CERN Document Server

    Chippendale, Aaron; Hay, Stuart

    2014-01-01

    We describe the development of a noise-temperature testing capability for phased-array antennas operating in receive mode from 0.7 GHz to 1.8 GHz. Sampled voltages from each array port were recorded digitally as the zenith-pointing array under test was presented with three scenes: (1) a large microwave absorber at ambient temperature, (2) the unobstructed radio sky, and (3) broadband noise transmitted from a reference antenna centred over and pointed at the array under test. The recorded voltages were processed in software to calculate the beam equivalent noise temperature for a maximum signal-to-noise ratio beam steered at the zenith. We introduced the reference-antenna measurement to make noise measurements with reproducible, well-defined beams directed at the zenith and thereby at the centre of the absorber target. We applied a detailed model of cosmic and atmospheric contributions to the radio sky emission that we used as a noise-temperature reference. We also present a comprehensive analysis of measureme...

  12. The effects of phased-array antennas on the performance of radars utilizing pseudo-random noise coding

    Science.gov (United States)

    Howard, R. L.; Belcher, M. L.; Corey, L. E.

    This paper examines how the phased-array antenna affects a radar's performance when pseudorandom noise (PRN)-coded waveforms are used. Dispersion loss, compressed pulse shapes, and suppression of wideband sidelobes or grating lobes are examined, and their interdependencies for systems using PRN-coded waveforms are considered. It is shown that these performance characteristics are a function of signal bandwidth, subarray size, and antenna scan angle. The choice of filtering schemes in the receiver can also impact the performance.

  13. Combining the switched-beam and beam-steering capabilities in a 2-D phased array antenna system

    Science.gov (United States)

    Tsai, Yi-Che; Chen, Yin-Bing; Hwang, Ruey-Bing

    2016-01-01

    This paper presents the development, fabrication, and measurement of a novel beam-forming system consisting of 16 subarray antennas, each containing four aperture-coupled patch antennas, and the application of this system in smart wireless communication systems. The beam patterns of each of the subarray antennas can be switched toward one of nine zones over a half space by adjusting the specific phase delay angles among the four antenna elements. Furthermore, when all subarrays are pointed at the same zone, slightly continuous beam steering in around 1° increments can be achieved by dynamically altering the progressive phase delay angle among the subarrays. Phase angle calibration was implemented by coupling each transmitter output and down converter into the in-phase/quadrature baseband to calculate the correction factor to the weight. In addition, to validate the proposed concepts and the fabricated 2-D phased array antenna system, this study measured the far-field radiation patterns of the aperture-coupled patch array integrated with feeding networks and a phase-calibration system to carefully verify its spatially switched-beam and beam-steering characteristics at a center frequency of 2.4 GHz which can cover the industrial, scientific, and medical band and some long-term evolution applications. In addition, measured results were compared with calculated results, and agreement between them was observed.

  14. Measured Sensitivity of the First Mark II Phased Array Feed on an ASKAP Antenna

    CERN Document Server

    Chippendale, A P; Beresford, R J; Hampson, G A; Macleod, A; Shaw, R D; Brothers, M L; Cantrall, C; Forsyth, A R; Hay, S G; Leach, M

    2015-01-01

    This paper presents the measured sensitivity of CSIRO's first Mk. II phased array feed (PAF) on an ASKAP antenna. The Mk. II achieves a minimum system-temperature-over-efficiency $T_\\mathrm{sys}/\\eta$ of 78 K at 1.23 GHz and is 95 K or better from 835 MHz to 1.8 GHz. This PAF was designed for the Australian SKA Pathfinder telescope to demonstrate fast astronomical surveys with a wide field of view for the Square Kilometre Array (SKA).

  15. Compact self-grounded Bow-Tie antenna design for an UWB phased-array hyperthermia applicator.

    Science.gov (United States)

    Takook, Pegah; Persson, Mikael; Gellermann, Johanna; Trefná, Hana Dobšíček

    2017-01-08

    Using UWB hyperthermia systems has the potential to improve the heat delivery to deep seated tumours. In this paper, we present a novel self-grounded Bow-Tie antenna design which is to serve as the basis element in a phased-array applicator. The UWB operation in the frequency range of 0.43-1 GHz is achieved by immersing the antenna in a water bolus. The radiation characteristics are improved by appropriate shaping the water bolus and by inclusion of dielectric layers on the top of the radiating arms of the antenna. In order to find the most appropriate design, we use a combination of performance indicators representing the most important attributes of the antenna. These are the UWB impedance matching, the transmission capability and the effective field size. The antenna was constructed and experimentally validated on muscle-like phantom. The measured reflection and transmission coefficients as well as radiation characteristics are in excellent agreement with the simulated results. MR image acquisitions with antenna located inside MR bore indicate a negligible distortion of the images by the antenna itself, which indicates MR compatibility.

  16. Broadband conformal phased array with optical beam forming for airborne satellite communication

    NARCIS (Netherlands)

    Schippers, H.; Verpoorte, J.; Jorna, P.; Hulzinga, A.; Meijerink, A.; Roeloffzen, C.G.H.; Zhuang, L.; Marpaung, D.A.I.; Etten, van W.; Heideman, R.G.; Leinse, A.; Borreman, A.; Hoekman, M.; Wintels, M.

    2008-01-01

    For enhanced communication on board an aircraft, novel antenna systems with broadband satellite based capabilities are required. The technology will enhance airline operations by providing in-flight connectivity for flight crew information and will bring live TV and high speed Internet connectivity

  17. SPS solid state antenna power combiner

    Science.gov (United States)

    Fitzsimmons, G. W.

    1980-01-01

    A concept for a solar power satellite antenna power combiner which utilizes solid state dc-rf converters is described. To avoid the power combining losses associated with circuit hybrids it is proposed that the power from multiple solid state amplifiers be combined by direct coupling of each amplifier's output to the radiating antenna structure. The selected power-combining antenna consists of a printed (metalized) microstrip circuit on a ceramic type dielectric substrate which is backed by a shallow lightweight aluminum cavity which sums the power of four microwave sources. The antenna behaves like two one-half wavelength slot-line antennas coupled together via their common cavity structure. A significant feature of the antenna configuration selected is that the radiated energy is summed to yield a single radiated output phase which represents the average insertion phase of the four power amplifiers. This energy may be sampled and, by comparison with the input signal, one can phase error correct to maintain the insertion phase of all solid state power combining modules at exactly the same value. This insures that the insertion phase of each SPS power combining antenna module is identical. An experiment verification program is described.

  18. gLISA: geosynchronous Laser Interferometer Space Antenna concepts with off-the-shelf satellites

    CERN Document Server

    Tinto, Massimo; Buchman, Sasha; Tilley, Scott

    2014-01-01

    We discuss two geosynchronous gravitational wave mission concepts, which we generically name gLISA. One relies on the science instrument hosting program onboard geostationary commercial satellites, while the other takes advantage of recent developments in the aerospace industry that result in dramatic satellite and launching vehicle cost reductions for a dedicated geosynchronous mission. To achieve the required level of disturbance free-fall onboard these large and heavy platforms we propose a "two-stage" drag-free system, which incorporates the Modular Gravitational Reference Sensor (MGRS) (developed at Stanford University) and does not rely on the use of micro-Newton thrusters. Although both mission concepts are characterized by different technical and programmatic challenges, individually they could be flown and operated at a cost significantly lower than those of previously envisioned gravitational wave missions. We estimate both mission concepts to cost less than 500M US$ each, and in the year 2015 we wi...

  19. Considerations of digital phase modulation for narrowband satellite mobile communication

    Science.gov (United States)

    Grythe, Knut

    1990-01-01

    The Inmarsat-M system for mobile satellite communication is specified as a frequency division multiple access (FDMA) system, applying Offset Quadrature Phase Shift Keying (QPSK) for transmitting 8 kbit/sec in 10 kHz user channel bandwidth. We consider Digital Phase Modulation (DPM) as an alternative modulation format for INMARSAT-M. DPM is similar to Continuous Phase Modulation (CPM) except that DPM has a finite memory in the premodular filter with a continuous varying modulation index. It is shown that DPM with 64 states in the VA obtains a lower bit error rate (BER). Results for a 5 kHz system, with the same 8 kbit/sec transmitted bitstream, is also presented.

  20. 卫星电视天线射频电路中LC压控振荡器设计%LC VCO Design of Satellite TV Antenna RF Circuit

    Institute of Scientific and Technical Information of China (English)

    王魏; 黎希; 宫召英; 马晓英; 杨丽君; 王岳生

    2012-01-01

    A monolithic integrated voltage controlled oscillator (VCO) with low power, low phase noise and wide tuning range used in the satellite TV antenna RF circuit is designed. The PMOS tail current source and a MIM capacitor array structure is used so as to effectively reduce the phase noise,and ensure the enough tuning range. The proposed VCO achieved a tuning rang of 3.364 -4.022 GHz,and the central frequency is 3.7 GHz,the phase noise is -90.4 dBc/Hz at 100 Hz and -119.1 dBc/Hz at 1 MHz offset while dissipating2.5 mW from 1.8 V supply.%设计了一款应用于卫星电视天线电路中低功耗、低相噪的宽带单片集成压控振荡器.该振荡器利用PMOS尾电流源和MIM电容阵列结构.在保证调谐范围的前提下,有效地降低了相位噪声.使得该压控振荡器实现了3.384 ~4.022 GHz频段的覆盖,在中心频率为3.7 GHz时,100 Hz和1 MHz频偏处的相位噪声分别为-90.4 dBc/Hz和-119.1 dBc/Hz,工作电压下为1.8V,功耗仅为2.5 mW.

  1. GPS code phase variations (CPV) for GNSS receiver antennas and their effect on geodetic parameters and ambiguity resolution

    Science.gov (United States)

    Kersten, Tobias; Schön, Steffen

    2016-12-01

    Precise navigation and geodetic coordinate determination rely on accurate GNSS signal reception. Thus, the receiver antenna properties play a crucial role in the GNSS error budget. For carrier phase observations, a spherical radiation pattern represents an ideal receiver antenna behaviour. Deviations are known as phase centre corrections. Due to synergy of carrier and code phase, similar effects on the code exist named code phase variations (CPV). They are mainly attributed to electromagnetic interactions of several active and passive elements of the receiver antenna. Consequently, a calibration and estimation strategy is necessary to determine the shape and magnitudes of the CPV. Such a concept was proposed, implemented and tested at the Institut für Erdmessung. The applied methodology and the obtained results are reported and discussed in this paper. We show that the azimuthal and elevation-dependent CPV can reach maximum magnitudes of 0.2-0.3 m for geodetic antennas and up to maximum values of 1.8 m for small navigation antennas. The obtained values are validated by dedicated tests in the observation and coordinate domain. As a result, CPV are identified to be antenna- related properties that are independent from location and time of calibration. Even for geodetic antennas when forming linear combinations the CPV effect can be amplified to values of 0.4-0.6 m. Thus, a significant fractional of the Melbourne-Wübbena linear combination. A case study highlights that incorrect ambiguity resolution can occur due to neglecting CPV corrections. The impact on the coordinates which may reach up to the dm level is illustrated.

  2. GPS code phase variations (CPV) for GNSS receiver antennas and their effect on geodetic parameters and ambiguity resolution

    Science.gov (United States)

    Kersten, Tobias; Schön, Steffen

    2017-06-01

    Precise navigation and geodetic coordinate determination rely on accurate GNSS signal reception. Thus, the receiver antenna properties play a crucial role in the GNSS error budget. For carrier phase observations, a spherical radiation pattern represents an ideal receiver antenna behaviour. Deviations are known as phase centre corrections. Due to synergy of carrier and code phase, similar effects on the code exist named code phase variations (CPV). They are mainly attributed to electromagnetic interactions of several active and passive elements of the receiver antenna. Consequently, a calibration and estimation strategy is necessary to determine the shape and magnitudes of the CPV. Such a concept was proposed, implemented and tested at the Institut für Erdmessung. The applied methodology and the obtained results are reported and discussed in this paper. We show that the azimuthal and elevation-dependent CPV can reach maximum magnitudes of 0.2-0.3 m for geodetic antennas and up to maximum values of 1.8 m for small navigation antennas. The obtained values are validated by dedicated tests in the observation and coordinate domain. As a result, CPV are identified to be antenna- related properties that are independent from location and time of calibration. Even for geodetic antennas when forming linear combinations the CPV effect can be amplified to values of 0.4-0.6 m. Thus, a significant fractional of the Melbourne-Wübbena linear combination. A case study highlights that incorrect ambiguity resolution can occur due to neglecting CPV corrections. The impact on the coordinates which may reach up to the dm level is illustrated.

  3. BEAM-FORMING ERRORS IN MURCHISON WIDEFIELD ARRAY PHASED ARRAY ANTENNAS AND THEIR EFFECTS ON EPOCH OF REIONIZATION SCIENCE

    Energy Technology Data Exchange (ETDEWEB)

    Neben, Abraham R.; Hewitt, Jacqueline N.; Dillon, Joshua S.; Goeke, R.; Morgan, E. [Kavli Institute for Astrophysics and Space Research, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Bradley, Richard F. [Dept. of Electrical and Computer Engineering, University of Virginia, Charlottesville, VA, 22904 (United States); Bernardi, G. [Square Kilometre Array South Africa (SKA SA), Cape Town 7405 (South Africa); Bowman, J. D. [School of Earth and Space Exploration, Arizona State University, Tempe, AZ 85287 (United States); Briggs, F. [Research School of Astronomy and Astrophysics, Australian National University, Canberra, ACT 2611 (Australia); Cappallo, R. J.; Corey, B. E.; Lonsdale, C. J.; McWhirter, S. R. [MIT Haystack Observatory, Westford, MA 01886 (United States); Deshpande, A. A. [Raman Research Institute, Bangalore 560080 (India); Greenhill, L. J. [Harvard-Smithsonian Center for Astrophysics, Cambridge, MA 02138 (United States); Hazelton, B. J.; Morales, M. F. [Department of Physics, University of Washington, Seattle, WA 98195 (United States); Johnston-Hollitt, M. [School of Chemical and Physical Sciences, Victoria University of Wellington, Wellington 6140 (New Zealand); Kaplan, D. L. [Department of Physics, University of Wisconsin–Milwaukee, Milwaukee, WI 53201 (United States); Mitchell, D. A. [CSIRO Astronomy and Space Science (CASS), P.O. Box 76, Epping, NSW 1710 (Australia); and others

    2016-03-20

    Accurate antenna beam models are critical for radio observations aiming to isolate the redshifted 21 cm spectral line emission from the Dark Ages and the Epoch of Reionization (EOR) and unlock the scientific potential of 21 cm cosmology. Past work has focused on characterizing mean antenna beam models using either satellite signals or astronomical sources as calibrators, but antenna-to-antenna variation due to imperfect instrumentation has remained unexplored. We characterize this variation for the Murchison Widefield Array (MWA) through laboratory measurements and simulations, finding typical deviations of the order of ±10%–20% near the edges of the main lobe and in the sidelobes. We consider the ramifications of these results for image- and power spectrum-based science. In particular, we simulate visibilities measured by a 100 m baseline and find that using an otherwise perfect foreground model, unmodeled beam-forming errors severely limit foreground subtraction accuracy within the region of Fourier space contaminated by foreground emission (the “wedge”). This region likely contains much of the cosmological signal, and accessing it will require measurement of per-antenna beam patterns. However, unmodeled beam-forming errors do not contaminate the Fourier space region expected to be free of foreground contamination (the “EOR window”), showing that foreground avoidance remains a viable strategy.

  4. Thermal imaging of plasma with a phased array antenna in QUEST

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, Kishore, E-mail: mishra@triam.kyushu-u.ac.jp; Nagata, K.; Akimoto, R.; Banerjee, S. [IGSES, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan); Idei, H.; Zushi, H.; Hanada, K.; Hasegawa, M.; Nakamura, K.; Fujisawa, A.; Nagashima, Y.; Onchi, T.; Kuzmin, A. [RIAM, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan); Yamamoto, M. K. [Research Institute for Sustainable Humanosphere, Kyoto University, Uji 611-0011 (Japan)

    2014-11-15

    A thermal imaging system to measure plasma Electron Bernstein Emission (EBE) emanating from the mode conversion region in overdense plasma is discussed. Unlike conventional ECE/EBE imaging, this diagnostics does not employ any active mechanical scanning mirrors or focusing optics to scan for the emission cones in plasma. Instead, a standard 3 × 3 waveguide array antenna is used as a passive receiver to collect emission from plasma and imaging reconstruction is done by accurate measurements of phase and intensity of these signals by heterodyne detection technique. A broadband noise source simulating the EBE, is installed near the expected mode conversion region and its position is successfully reconstructed using phase array technique which is done in post processing.

  5. High Integrated Microwave Architecture Using LTCC-SIP Technology in Active Phased Array Antenna Applications

    Science.gov (United States)

    Zhou, Jun; Shi, Wei; Dou, Wen-Bin; Shen, Ya

    2012-06-01

    A kind of three dimensional Low Temperature Co-fired Ceramic (LTCC)-System in Package (SIP) transition was proposed in this paper. The basic design of SIP with LTCC technology was done by vertical transitions which transmit the microwave signal from the bottom to the surface of the substrate. The measured insertion loss did not exceed 1.5 dB, which contains the insertion loss of the test board about 0.6 dB at 18 GHz and the return loss was better than-15 dB up to 18 GHz. Then this technology was applied to a kind of phase shifting and amplifier module with two output ports. Basing on this module, a miniature Ku-band active phase array antenna was realized. The design results in a small size(84.8 mm×84.8 mm×55 mm). The measured performance of systems radiation pattern was also given.

  6. Reconfigurable phased antenna array for extending cubesat operations to Ka-band: Design and feasibility

    Science.gov (United States)

    Buttazzoni, G.; Comisso, M.; Cuttin, A.; Fragiacomo, M.; Vescovo, R.; Vincenti Gatti, R.

    2017-08-01

    Started as educational tools, CubeSats have immediately encountered the favor of the scientific community, subsequently becoming viable platforms for research and commercial applications. To ensure competitive data rates, some pioneers have started to explore the usage of the Ka-band beside the conventional amateur radio frequencies. In this context, this study proposes a phased antenna array design for Ka-band downlink operations consisting of 8×8 circularly polarized subarrays of microstrip patches filling one face of a single CubeSat unit. The conceived structure is developed to support 1.5 GHz bandwidth and dual-task missions, whose feasibility is verified by proper link budgets. The dual-task operations are enabled by a low-complexity phase-only control algorithm that provides pattern reconfigurability in order to satisfy both orbiting and intersatellite missions, while remaining adherent to the cost-effective CubeSat paradigm.

  7. Application of Hybrid Along-Track Interferometry/Displaced Phase Center Antenna Method for Moving Human Target Detection in Forest Environments

    Science.gov (United States)

    2016-10-01

    Antenna Method for Moving Human Target Detection in Forest Environments by DaHan Liao Approved for public release...Research Laboratory Application of Hybrid Along-Track Interferometry/Displaced Phase Center Antenna Method for Moving Human Target Detection...Phase Center Antenna Method for Moving Human Target Detection in Forest Environments 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT

  8. Triple Band Parasitic Array Antenna for C-X-Ku-Band Application Using Out-of-Phase Coupling Approach

    Directory of Open Access Journals (Sweden)

    Anubhuti Khare

    2014-01-01

    Full Text Available Triple band parasitic array antenna for C-X-Ku-band application is presented. The proposed antenna is designed using the concept of parasitic array and out-of-phase coupling approach. The objects of research are to optimize total inductance of geometry by using out-of-phase inductance approach. The out of phase inductance of geometry consists of using two U-patches novel director on the left side of geometry, appropriate dimension of ground plan, and gap coupling between parasitic and active patches. The dimension of the ground plan geometry is 0.5λ mil × 0.5154λ mil. The usable impedance bandwidth of design antenna is “5.8 GHz to 18 GHz” (102% impedance bandwidth and gain enhancement is up to 11.8 dBi. The proposed antenna can be used for X-Ku band and C-band applications. Both simulated and measured results are presented, which are in good agreement. The proposed antenna was fabricated with a thin copper layer printed on a thin lossy FR4 substrate for low-cost production.

  9. L-Band Transmit/Receive Module for Phase-Stable Array Antennas

    Science.gov (United States)

    Andricos, Constantine; Edelstein, Wendy; Krimskiy, Vladimir

    2008-01-01

    Interferometric synthetic aperture radar (InSAR) has been shown to provide very sensitive measurements of surface deformation and displacement on the order of 1 cm. Future systematic measurements of surface deformation will require this capability over very large areas (300 km) from space. To achieve these required accuracies, these spaceborne sensors must exhibit low temporal decorrelation and be temporally stable systems. An L-band (24-cmwavelength) InSAR instrument using an electronically steerable radar antenna is suited to meet these needs. In order to achieve the 1-cm displacement accuracy, the phased array antenna requires phase-stable transmit/receive (T/R) modules. The T/R module operates at L-band (1.24 GHz) and has less than 1- deg absolute phase stability and less than 0.1-dB absolute amplitude stability over temperature. The T/R module is also high power (30 W) and power efficient (60-percent overall efficiency). The design is currently implemented using discrete components and surface mount technology. The basic T/R module architecture is augmented with a calibration loop to compensate for temperature variations, component variations, and path loss variations as a function of beam settings. The calibration circuit consists of an amplitude and phase detector, and other control circuitry, to compare the measured gain and phase to a reference signal and uses this signal to control a precision analog phase shifter and analog attenuator. An architecture was developed to allow for the module to be bidirectional, to operate in both transmit and receive mode. The architecture also includes a power detector used to maintain a transmitter power output constant within 0.1 dB. The use of a simple, stable, low-cost, and high-accuracy gain and phase detector made by Analog Devices (AD8302), combined with a very-high efficiency T/R module, is novel. While a self-calibrating T/R module capability has been sought for years, a practical and cost-effective solution has

  10. Direct Optimization of Printed Reflectarrays for Contoured Beam Satellite Antenna Applications

    DEFF Research Database (Denmark)

    Zhou, Min; Sorensen, Stig B.; Kim, Oleksiy S.

    2013-01-01

    An accurate and efficient direct optimization technique for the design of contoured beam reflectarrays is presented. It is based on the spectral domain method of moments assuming local periodicity and minimax optimization. Contrary to the conventional phase-only optimization techniques, the geome......An accurate and efficient direct optimization technique for the design of contoured beam reflectarrays is presented. It is based on the spectral domain method of moments assuming local periodicity and minimax optimization. Contrary to the conventional phase-only optimization techniques...

  11. System-Level Integrated Circuit (SLIC) Technology Development for Phased Array Antenna Applications

    Science.gov (United States)

    Windyka, John A.; Zablocki, Ed G.

    1997-01-01

    This report documents the efforts and progress in developing a 'system-level' integrated circuit, or SLIC, for application in advanced phased array antenna systems. The SLIC combines radio-frequency (RF) microelectronics, digital and analog support circuitry, and photonic interfaces into a single micro-hybrid assembly. Together, these technologies provide not only the amplitude and phase control necessary for electronic beam steering in the phased array, but also add thermally-compensated automatic gain control, health and status feedback, bias regulation, and reduced interconnect complexity. All circuitry is integrated into a compact, multilayer structure configured for use as a two-by-four element phased array module, operating at 20 Gigahertz, using a Microwave High-Density Interconnect (MHDI) process. The resultant hardware is constructed without conventional wirebonds, maintains tight inter-element spacing, and leads toward low-cost mass production. The measured performances and development issues associated with both the two-by-four element module and the constituent elements are presented. Additionally, a section of the report describes alternative architectures and applications supported by the SLIC electronics. Test results show excellent yield and performance of RF circuitry and full automatic gain control for multiple, independent channels. Digital control function, while suffering from lower manufacturing yield, also proved successful.

  12. Optical beam control of mm-wave phased array antennas for communications

    Science.gov (United States)

    Daryoush, A.; Herczfeld, P.; Contarino, V.; Rosen, A.; Turski, Z.

    1987-03-01

    Large-aperture phased array antennas are designed with fiber-optic (FO) distribution networks to provide phase and frequency reference signals, control signals for beamsteering and beamshaping, and data/frequency hopping signals to MMIC active transmit/receive modules. The experimental results of an FO communication network at the mm-wave frequency of 38 GHz (Ka band) are presented. The results of 500 MHz to 1 GHz FO link characteristics such as frequency response flatness, harmonics, and third-order intermodulation distortion are presented. Results of stabilization of a 38 GHz IMPATT oscillator using indirect optical injection locking is also discussed. A locking range of 132 MHz using 45 dB amplification gain is demonstrated. The overall system FM noise degradation is measured to be 16 dB. The communication link is established by upconversion of the data link with the stabilized LO. Results of a true time delay phase shifter using a novel fiber-stretching technique is presented. A phase shift as high as 20 deg at 10 GHz is achieved using the expansion properties of a piezoelectric ring excited by a dc voltage.

  13. Fully Printed High-Frequency Phased-Array Antenna on Flexible Substrate

    Science.gov (United States)

    Chen, Yihong; Lu, Xuejun

    2010-01-01

    To address the issues of flexible electronics needed for surface-to-surface, surface-to-orbit, and back-to-Earth communications necessary for manned exploration of the Moon, Mars, and beyond, a room-temperature printing process has been developed to create active, phased-array antennas (PAAs) on a flexible Kapton substrate. Field effect transistors (FETs) based on carbon nanotubes (CNTs), with many unique physical properties, were successfully proven feasible for phased-array antenna systems. The carrier mobility of an individual CNT is estimated to be at least 100,000 sq cm/V(dot)s. The CNT network in solution has carrier mobility as high as 46,770 sq cm/V(dot)s, and has a large current-density carrying capacity of approx. 1,000 mA/sq cm , which corresponds to a high carrying power of over 2,000 mW/ sq cm. Such high carrier mobility, and large current carrying capacity, allows the achievement of high-speed (>100 GHz), high-power, flexible electronic circuits that can be monolithically integrated on NASA s active phasedarray antennas for various applications, such as pressurized rovers, pressurized habitats, and spacesuits, as well as for locating beacon towers for lunar surface navigation, which will likely be performed at S-band and attached to a mobile astronaut. A fully printed 2-bit 2-element phasedarray antenna (PAA) working at 5.6 GHz, incorporating the CNT FETs as phase shifters, is demonstrated. The PAA is printed out at room temperature on 100-mm thick Kapton substrate. Four CNT FETs are printed together with microstrip time delay lines to function as a 2-bit phase shifter. The FET switch exhibits a switching speed of 0.2 ns, and works well for a 5.6-GHz RF signal. The operating frequency is measured to be 5.6 GHz, versus the state-of-the-art flexible FET operating frequency of 52 MHz. The source-drain current density is measured to be over 1,000 mA/sq cm, while the conventional organic FETs, and single carbon nanotube-based FETs, are typically in the m

  14. Developing an integrated photonic system with a simple beamforming architecture for phased-array antennas.

    Science.gov (United States)

    Zhou, Weimin; Stead, Michael; Weiss, Steven; Okusaga, Olukayode; Jiang, Lingjun; Anderson, Stephen; Rena Huang, Z

    2017-01-20

    We have designed a simplified true-time-delay beamforming architecture using integrated photonics for phased-array antennas. This architecture can independently control multiple RF beams simultaneously with only a single tuning parameter to steer the beam in each direction for each beam. We have made a proof-of-the-principle demonstration of an X-band, 30×4-elements, fiber-optics-based beamformer for one-dimensional steering in transmission mode. The goal is to develop a semiconductor-based integrated photonic circuit so that a 2D beamforming array for both transmit and receive operations can be made on a single chip. For that, we have designed a Si-based integrated waveguide circuit using two types of "slow-light" waveguide for tunable time delays for two-dimensional steering.

  15. Optical True Time Delay for Phased Array Antennas Composed of 2×2 Optical MEMS Switches and Fiber Delay Lines

    Institute of Scientific and Technical Information of China (English)

    Back-Song; Lee; Jong-Dug; Shin; Boo-Gyoun; Kim

    2003-01-01

    We proposed an optical true time delay (TTD) for phased array antennas (PAAs) composed of 2×2 optical MEMS switches, single-mode fiber delay lines, and a fixed wavelength laser diode. A 3-bit TTD for 10 GHz PAAs was implemented with a time delay error less than ± 0.2 ps.

  16. Multi-wavelength integrated optical beamformer based on Wavelength division multiplexing for 2-D phased array antennas

    NARCIS (Netherlands)

    Burla, Maurizio; Marpaung, David; Zhuang, Leimeng; Khan, Muhannad Rezaul; Leinse, Arne; Beeker, Willem; Hoekman, Marcel; Heideman, René; Roeloffzen, Chris

    2014-01-01

    A novel, hardware-compressive architecture for broadband and continuously tunable integrated optical truetime- delay beamformers for phased array antennas is proposed and experimentally demonstrated. The novel idea consists in employing the frequency-periodic response of optical ring resonator (ORR)

  17. Design on configurations of multi-beam antenna of LEO communication satellite%LEO通信卫星多波束天线构型方案设计

    Institute of Scientific and Technical Information of China (English)

    赵星惟; 吕源; 刘会杰; 梁旭文

    2011-01-01

    We present systematic analysis and planning of multi-beam antenna based on the features of LEO communication satellite. First, the reasons for adopting multi-beam antenna system are analyzed. Calculations of system parameters within the satellite coverage range are performed based on 7-beam equal-coverage-area scheme. System parameters, like beam width and beam angle, are given. Then, the scheme of array antenna is elaborated and analyzed. Some beamforming and multiplexing schemes are designed and analyzed.%针对低轨道(LEO)通信卫星的特点,进行星载多波束天线的系统级分析和规划.首先,对天线体制选择多波束天线的原因进行了论述.基于卫星覆盖范围的指标,进行了7波束等覆盖面积方案下波束指标的计算,给出了波束宽度、夹角等系统指标.然后对阵列天线方案进行了详细论述.最后对波束形成方案以及复用方案进行了设计和分析.

  18. Opto-VLSI-based photonic true-time delay architecture for broadband adaptive nulling in phased array antennas.

    Science.gov (United States)

    Juswardy, Budi; Xiao, Feng; Alameh, Kamal

    2009-03-16

    This paper proposes a novel Opto-VLSI-based tunable true-time delay generation unit for adaptively steering the nulls of microwave phased array antennas. Arbitrary single or multiple true-time delays can simultaneously be synthesized for each antenna element by slicing an RF-modulated broadband optical source and routing specific sliced wavebands through an Opto-VLSI processor to a high-dispersion fiber. Experimental results are presented, which demonstrate the principle of the true-time delay unit through the generation of 5 arbitrary true-time delays of up to 2.5 ns each.

  19. Compact optical true time delay beamformer for a 2D phased array antenna using tunable dispersive elements.

    Science.gov (United States)

    Ye, Xingwei; Zhang, Fangzheng; Pan, Shilong

    2016-09-01

    A hardware-compressive optical true time delay architecture for 2D beam steering in a planar phased array antenna is proposed using fiber-Bragg-grating-based tunable dispersive elements (TDEs). For an M×N array, the proposed system utilizes N TDEs and M wavelength-fixed optical carriers to control the time delays. Both azimuth and elevation beam steering are realized by programming the settings of the TDEs. An experiment is carried out to demonstrate the delay controlling in a 2×2 array, which is fed by a wideband pulsed signal. Radiation patterns calculated from the experimentally measured waveforms at the four antennas match well with the theoretical results.

  20. Effects of the Number of Active Receiver Channels on the Sensitivity of a Reflector Antenna System with a Multi-Beam Wideband Phased Array Feed

    CERN Document Server

    Iupikov, O

    2016-01-01

    A method for accurate modeling of a reflector antenna system with a wideband phased array feed is presented and used to study the effects of the number of active antenna elements and associated receiving channels on the receiving sensitivity of the antenna system. Numerical results are shown for a practical design named APERTIF that is currently under developed at The Netherlands Institute for Radio Astronomy (ASTRON).

  1. Control system of satellite TV antenna of strapdown shipborne%捷联式船载卫星电视天线控制系统

    Institute of Scientific and Technical Information of China (English)

    秦爱民; 闫英敏; 闫建生; 靳英卫

    2011-01-01

    With the progress of the society and the improvements of information technology, people need more TV programmes through satellite networks while moving. A strapdown shipborne satellite TV antenna control system based on DSP is introduced. The architectures of the software and hardware of the control system are given, and the functions of different components are described in detail. The stabilization and the automatic tracking are realized in this antenna control system for satellite television.%随着社会的进步和信息化技术的提高,人们对移动中通过卫星网路接收卫星电视节目的需求越来越大.介绍了基于DSP的捷联式船载卫星电视天线控制系统,阐述了系统软硬件的结构及各部分的功能,实现了船载卫星电视天线的稳定与自动跟踪卫星.

  2. Cantilever RF-MEMS for monolithic integration with phased array antennas on a PCB

    Science.gov (United States)

    Aguilar-Armenta, C. J.; Porter, S. J.

    2015-12-01

    This article presents the development and operation of a novel electrostatic metal-to-metal contact cantilever radio-frequency microelectromechanical system (RF-MEMS) switch for monolithic integration with microstrip phased array antennas (PAAs) on a printed circuit board. The switch is fabricated using simple photolithography techniques on a Rogers 4003c substrate, with a footprint of 200 µm × 100 µm, based on a 1 µm-thick copper cantilever. An alternative wet-etching technique for effectively releasing the cantilever is described. Electrostatic and electromagnetic measurements show that the RF-MEMS presents an actuation voltage of 90 V for metal-to-metal contact, an isolation of -8.7 dB, insertion loss of -2.5 dB and a return loss of -15 dB on a 50 Ω microstrip line at 12.5 GHz. For proof-of-concept, a beam-steering 2 × 2 microstrip PAA, based on two 1-bit phase shifters suitable for the monolithic integration of the RF-MEMS, has been designed and measured at 12.5 GHz. Measurements show that the beam-steering system presents effective radiation characteristics with scanning capabilities from broadside towards 29° in the H-plane.

  3. A Switchable 3D-Coverage Phased Array Antenna Package for 5G Mobile Terminals

    DEFF Research Database (Denmark)

    Ojaroudiparchin, Naser; Shen, Ming; Zhang, Shuai;

    2016-01-01

    antennas have been compactly arranged along the edge region of the mobile phone PCB to form the antenna package. By switching the feeding to one of the sub arrays, the desired direction of coverage can be achieved. The proposed design has >10 dB gain in the upper spherical space, good directivity...

  4. 卫星便携站天线自动对星系统的设计与实现%Design and implement of satellite auto-aiming system on antenna of satellite portable station

    Institute of Scientific and Technical Information of China (English)

    胡明; 王星全; 郑振华; 杨华

    2012-01-01

    In the porcess of narrow-beam portable station antenna aiming the satellite, there are three problems: finding the satellite difficulty, aiming the satellite long-time and low-precision. In this article, an auto-aim instrument on equipment is designed and implemented. This instrument based on PIC singlechip can implement rapid, automatic and precise aiming the satellite by collecting and porcessing the data from GPS and sensors and signal strength module, controling stepping motors to adjust the azimuth and elevation of portable station antenna. Using this system, we can reduce the time, improve the precision in aiming the satellite and prove the efficiency of communication markedly.%针对卫星便携站窄波束天线找星难度大、对星耗时多、对星精度差的问题,设计并实现了一个附加在实装设备上的自动对星工具,以PIC单片机为核心,通过采集和处理GPS数据、方位俯仰传感器数据和卫星信号强度数据,控制高精度步进电机自动调整便携站天线方位角和俯仰角,从而实现快速、自动、精确对星.通过使用高精度步进电机代替传统手工操作,能够明显缩短对星时间、提高对星精度,且体积较小、安装拆卸容易、携带方便,显著提高了通信效能.

  5. A Beam Tracking Algorithm Based on Satellite Beacon Signals for Phased Array in Mobile Satellite Communications%一种基于信标的移动卫通相控阵波束跟踪算法

    Institute of Scientific and Technical Information of China (English)

    陈鹏; 张慧

    2012-01-01

    In this paper a beam tracking algorithm based on satellite beacon signals is proposed and realized. The method is suitable for all kinds of phased array type mobile satellite communication antennas. It overcomes the difficulty of detecting the extremely weak satellite beacon signals and then the tracking performance is greatly improved. The highlight of the algorithm is the beam tracking process can be run without the help of gyroscopes and thus improves the survivability in the extreme environments. The algorithm was implemented and verified in a Ku band phased array mobile satellite antenna.%提出并实现了一种利用卫星信标信号来实施基于相控阵天线的波束跟踪算法。该方法适用于采用相控阵天线技术的各种卫星“动中通”天线,克服了卫星信标信号强度弱,检测困难的弱点,提高了跟踪信噪比,同时采用了软件无线电方式解调可以提供最大的灵活性。跟踪算法的最大优点是没有任何陀螺仪的辅助,极大地提高了天线在各种极端运动环境下的适应能力。算法最终在自行研制的Ku波段相控阵移动卫星天线系统上获得验证。

  6. Printable Silicon Nanomembranes for Solar-Powered, Bi-Directional Phased-Array-Antenna Communication System on Flexible Substrates

    Science.gov (United States)

    2013-04-01

    Identification (RFID), Large Area Flexible Displays, Electronic Paper, Bio-Sensors, Large Area Conformal and Flexible Antennas, Smart and Interactive Textiles ... market . 4. ACCOMPLISHMENTS/NEW FINDINGS Through this Phase II program, we have achieved several important milestones that can form the basis for future...displays [58], flexible silicon integrated circuits [59], photonic crystal filters [60, 61], smart skins [62], etc. Among all the transferable

  7. Antennas Designed for Advanced Communications for Air Traffic Management (AC/ATM) Project

    Science.gov (United States)

    Zakrajsek, Robert J.

    2000-01-01

    The goal of the Advanced Communications for Air Traffic Management (AC/ATM) Project at the NASA Glenn Research Center at Lewis Field is to enable a communications infrastructure that provides the capacity, efficiency, and flexibility necessary to realize a mature free-flight environment. The technical thrust of the AC/ATM Project is targeted at the design, development, integration, test, and demonstration of enabling technologies for global broadband aeronautical communications. Since Ku-band facilities and equipment are readily available, one of the near-term demonstrations involves a link through a Kuband communications satellite. Two conformally mounted antennas will support the initial AC/ATM communications links. Both of these are steered electronically through monolithic microwave integrated circuit (MMIC) amplifiers and phase shifters. This link will be asymmetrical with the downlink to the aircraft (mobile vehicle) at a throughput rate of greater than 1.5 megabits per second (Mbps), whereas the throughput rate of the uplink from the aircraft will be greater than 100 kilobits per second (kbps). The data on the downlink can be narrow-band, wide-band, or a combination of both, depending on the requirements of the experiment. The AC/ATM project is purchasing a phased-array Ku-band transmitting antenna for the uplink from the test vehicle. Many Ku-band receiving antennas have been built, and one will be borrowed for a short time to perform the initial experiments at the NASA Glenn Research Center at Lewis Field. The Ku-band transmitting antenna is a 254-element MMIC phased-array antenna being built by Boeing Phantom Works. Each element can radiate 100 mW. The antenna is approximately 43-cm high by 24-cm wide by 3.3-cm thick. It can be steered beyond 60 from broadside. The beamwidth varies from 6 at broadside to 12 degrees at 60 degrees, which is typical of phased-array antennas. When the antenna is steered to 60 degrees, the beamwidth will illuminate

  8. Hybrid Differential Evolution with Biogeography-Based Optimization for Design of a Reconfigurable Antenna Array with Discrete Phase Shifters

    Directory of Open Access Journals (Sweden)

    Xiangtao Li

    2011-01-01

    Full Text Available Multibeam antenna arrays have important applications in communications and radar. This paper presents a new method of designing a reconfigurable antenna with quantized phase excitations using a new hybrid algorithm, called DE/BBO. The reconfigurable design problem is to find the element excitation that will result in a sector pattern main beam with low sidelobes with additional requirement that the same excitation amplitudes applied to the array with zero-phase should be in a high directivity, low sidelobe pencil-shaped main beam. In order to reduce the effect of mutual coupling between the antenna-array elements, the dynamic range ratio is minimized. Additionally, compared with the continuous realization and subsequent quantization, experimental results indicate that the performance of the discrete realization of the phase excitation value can be improved. In order to test the performances of hybrid differential evolution with biogeography-based optimization, the results of some state-of-art algorithms are considered, for the purposed of comparison. Experiment results indicate the better performance of the DE/BBO.

  9. An Efficient Beam Steerable Antenna Array Concept for Airborne Applications

    Directory of Open Access Journals (Sweden)

    H. Aliakbarian

    2014-04-01

    Full Text Available Deployment of a satellite borne, steerable antenna array with higher directivity and gain in Low Earth Orbit makes sense to reduce ground station complexity and cost, while still maintaining a reasonable link budget. The implementation comprises a digitally beam steerable phased array antenna integrated with a complete system, comprising the antenna, hosting platform, ground station, and aircraft based satellite emulator to facilitate convenient aircraft based testing of the antenna array and ground-space communication link. This paper describes the design, development and initial successful interim testing of the various subsystems. A two element prototype used in this increases the signal-to-noise ratio (SNR by 3 dB which is corresponding to more than 10 times better bit error rate (BER.

  10. Radio interferometry and satellite tracking

    CERN Document Server

    Kawase, Seiichiro

    2012-01-01

    Worldwide growth of space communications has caused a rapid increase in the number of satellites operating in geostationary orbits, causing overcrowded orbits. This practical resource is designed to help professionals overcome this problem. This timely book provides a solid understanding of the use of radio interferometers for tracking and monitoring satellites in overcrowded environments. Practitioners learn the fundamentals of radio interferometer hardware, including antennas, receiving equipment, signal processing and phase detection, and measurement accuracies. This in-depth volume describ

  11. Exploiting Phase Diversity for CDMA2000 1X Smart Antenna Base Stations

    Directory of Open Access Journals (Sweden)

    Hyeon Seungheon

    2004-01-01

    Full Text Available A performance analysis of an access channel decoder is presented which exploits a diversity gain due to the independent magnitude of received signals energy at each of the antenna elements of a smart-antenna base-station transceiver subsystem (BTS operating in CDMA2000 1X signal environment. The objective is to enhance the data retrieval at cellsite during the access period, for which the optimal weight vector of the smart antenna BTS is not available. It is shown in this paper that the access channel decoder proposed in this paper outperforms the conventional one, which is based on a single antenna channel in terms of detection probability of access probe, access channel failure probability, and Walsh-code demodulation performance.

  12. End-Fire Phased Array 5G Antenna Design Using Leaf-Shaped Bow-Tie Elements for 28/38 GHz MIMO Applications

    DEFF Research Database (Denmark)

    Ojaroudiparchin, Naser; Shen, Ming; Pedersen, Gert F.

    2016-01-01

    In this paper, a new design of mm-Wave phased array 5G antenna for multiple-input multiple-output (MIMO) applications has been introduced. Two identical linear phased arrays with eight leaf-shaped bow-tie antenna elements have been used at different sides of the mobile-phone PCB. An Arlon AR 350...... at 28 and 38 GHz which both are powerful candidates to be the carrier frequency of the future 5G cellular networks....

  13. Initiating an error budget of the DORIS ground antenna position: Genesis of the Starec antenna type C

    Science.gov (United States)

    Saunier, J.; Auriol, A.; Tourain, C.

    2016-12-01

    The DORIS system measures distances between phase centers of onboard and ground antennas to determine the position of the satellites in their orbits. To this end, the ground antenna phase center position must be known in a terrestrial reference frame. Its position is linked and defined with respect to the antenna reference point (ARP), a conventional physical point for which coordinates are assigned. Although the determination of the ARP position with respect to ground markers can be achieved by traditional surveys, the connection with the actual measurement point (phase center) is far more difficult to determine. This is the main concern explored in this paper. Regardless of the need for a good antenna characterization, CNES and IGN jointly worked to establish a first error budget of the ground antenna position. With this aim in view, each component was clearly identified and studied separately. We distinguished between errors from manufacturing and from site surveying and, on the other hand, errors affecting horizontal and vertical position. The knowledge of the antenna geometry and the guarantee of a good reproducibility in the manufacturing process are essential. Based on these requirements, we have defined new manufacturing specifications to create a new antenna type: Starec type C. Compared to the previous antenna (Starec type B), the standard uncertainty of the 2 GHz phase center position in the vertical direction has been reduced from 5 mm to 1 mm. Following this work, we provide for the new Starec antenna (type C) total uncertainties involved in the ground antenna positioning in a local reference frame: 2 mm in the horizontal plane, 2.5 mm for the vertical component and 3.2 mm in three-dimensional combination. We also propose for DORIS new definitions of conventional points and a new method to determine ground antennas position that were not possible before this manufacturing specifications change.

  14. Micro-Satellite Attitude Determination Using GPS Carrier Phases

    Institute of Scientific and Technical Information of China (English)

    He Xiu-feng; Ling Keck-voon

    2003-01-01

    GPS is an attractive attitude sensor for micro-satellites due to small package and advantage for cost savings. However, the major difficulty in attitude determination for a micro-satellite is that baseline lengths are short (less than a meter) . Thus , to obtain precise accuracy of attitudes for a micro-satellite, the algorithm selection and error source calibration are important. In this paper, a technique based on the attitude cost function is proposed. To verify the method proposed, the experiments have been conducted. The results indicate that attitude errors are less than 1 deg.

  15. Analysis of the phase control of the ITER ICRH antenna array. Influence on the load resilience and radiated power spectrum

    Science.gov (United States)

    Messiaen, A.; Swain, D.; Ongena, J.; Vervier, M.

    2015-12-01

    The paper analyses how the phasing of the ITER ICRH 24 strap array evolves from the power sources up to the strap currents of the antenna. The study of the phasing control and coherence through the feeding circuits with prematching and automatic matching and decoupling network is made by modeling starting from the TOPICA matrix of the antenna array for a low coupling plasma profile and for current drive phasing (worst case for mutual coupling effects). The main results of the analysis are: (i) the strap current amplitude is well controlled by the antinode Vmax amplitude of the feeding lines, (ii) the best toroidal phasing control is done by the adjustment of the mean phase of Vmax of each poloidal straps column, (iii) with well adjusted system the largest strap current phasing error is ±20°, (iv) the effect on load resilience remains well below the maximum affordable VSWR of the generators, (v) the effect on the radiated power spectrum versus k// computed by means of the coupling code ANTITER II remains small for the considered cases.

  16. Analysis of the phase control of the ITER ICRH antenna array. Influence on the load resilience and radiated power spectrum

    Energy Technology Data Exchange (ETDEWEB)

    Messiaen, A., E-mail: a.messiaen@fz-juelich.de; Ongena, J.; Vervier, M. [Laboratory for Plasma Physics, ERM-KMS, TEC partner, Cycle, B1000-Brussels (Belgium); Swain, D. [US ITER Team, ORNL (United States)

    2015-12-10

    The paper analyses how the phasing of the ITER ICRH 24 strap array evolves from the power sources up to the strap currents of the antenna. The study of the phasing control and coherence through the feeding circuits with prematching and automatic matching and decoupling network is made by modeling starting from the TOPICA matrix of the antenna array for a low coupling plasma profile and for current drive phasing (worst case for mutual coupling effects). The main results of the analysis are: (i) the strap current amplitude is well controlled by the antinode V{sub max} amplitude of the feeding lines, (ii) the best toroidal phasing control is done by the adjustment of the mean phase of V{sub max} of each poloidal straps column, (iii) with well adjusted system the largest strap current phasing error is ±20°, (iv) the effect on load resilience remains well below the maximum affordable VSWR of the generators, (v) the effect on the radiated power spectrum versus k{sub //} computed by means of the coupling code ANTITER II remains small for the considered cases.

  17. Analysis of the phase control of the ITER ICRH antenna array. Influence on the load resilience and radiated power spectrum

    Energy Technology Data Exchange (ETDEWEB)

    Messiaen, Andre [Ecole Royale Militaire, Brussels Belgium; Swain, David W [ORNL; Ongena, Jef [Ecole Royale Militaire, Brussels Belgium; Vervier, Michael [Ecole Royale Militaire, Brussels Belgium

    2015-01-01

    The paper analyses how the phasing of the ITER ICRH 24 strap array evolves from the power sources up to the strap currents of the antenna. The study of the phasing control and coherence through the feeding circuits with prematching and automatic matching and decoupling network is made by modeling starting from the TOPICA matrix of the antenna array for a low coupling plasma profile and for current drive phasing (worst case for mutual coupling effects). The main results of the analysis are: (i) the strap current amplitude is well controlled by the antinode V-max amplitude of the feeding lines, (ii) the best toroidal phasing control is done by the adjustment of the mean phase of V-max of each poloidal straps column, (iii) with well adjusted system the largest strap current phasing error is +/- 20 degrees, (iv) the effect on load resilience remains well below the maximum affordable VSWR of the generators, (v) the effect on the radiated power spectrum versus k//computed by means of the coupling code ANTITER II remains small for the considered cases. [GRAPHICS] .

  18. Graphene-based fine-tunable optical delay line for optical beamforming in phased-array antennas.

    Science.gov (United States)

    Tatoli, Teresa; Conteduca, Donato; Dell'Olio, Francesco; Ciminelli, Caterina; Armenise, Mario N

    2016-06-01

    The design of an integrated graphene-based fine-tunable optical delay line on silicon nitride for optical beamforming in phased-array antennas is reported. A high value of the optical delay time (τg=920  ps) together with a compact footprint (4.15  mm2) and optical loss antennas. The delay line includes two graphene-based Mach-Zehnder interferometer switches and two vertically stacked microring resonators between which a graphene capacitor is placed. The tuning range is obtained by varying the value of the voltage applied to the graphene electrodes, which controls the optical path of the light propagation and therefore the delay time. The graphene provides a faster reconfigurable time and low values of energy dissipation. Such significant advantages, together with a negligible beam-squint effect, allow us to overcome the limitations of conventional RF beamformers. A highly efficient fine-tunable optical delay line for the beamsteering of 20 radiating elements up to ±20° in the azimuth direction of a tile in a phased-array antenna of an X-band synthetic aperture radar has been designed.

  19. Designing the next phase domestic satellites - A step to communication satellites as intelligent network nodes

    Science.gov (United States)

    Majus, J.

    1982-09-01

    Applications of satellite systems for telecommunication networks are discussed in terms of harmonizing the satellite capabilities with ground-based equipment, and design for the satellites are discussed. Modern network services are becoming increasingly digitized and use optic fiber switching and information transfer. Spaceborne nodes can be used for telephony, television, packet switching, leased lines, and teletex, with reserved sectors for point-to-point communications. Space systems are capable of 100% coverage, while terrestrial systems frequently have utilization rates near 5%, implying that demand-oriented satellite expansion of local systems is the suitable methodology. Technological requirements are explored, including exclusive use of digital processing, flexible flow rates, signal transmission times, and short time availability.

  20. Design and Performance Evaluation of a Dual Antenna Joint Carrier Tracking Loop

    Directory of Open Access Journals (Sweden)

    Wenfei Guo

    2015-10-01

    Full Text Available In order to track the carrier phases of Global Navigation Satellite Systems (GNSS signals in signal degraded environments, a dual antenna joint carrier tracking loop is proposed and evaluated. This proposed tracking loop processes inputs from two antennas, namely the master antenna and the slave antenna. The master antenna captures signals in open-sky environments, while the slave antenna capture signals in degraded environments. In this architecture, a Phase Lock Loop (PLL is adopted as a master loop to track the carrier phase of the open-sky signals. The Doppler frequency estimated by this master loop is utilized to assist weak carrier tracking in the slave loop. As both antennas experience similar signal dynamics due to satellite motion and clock frequency variations, a much narrower loop bandwidth and possibly a longer coherent integration can be adopted to track the weak signals in slave channels, by utilizing the Doppler aid from master channels. PLL tracking performance is affected by the satellite/user dynamics, clock instability, and thermal noise. In this paper, their impacts on the proposed phase tracking loop are analyzed and verified by both simulation and field data. Theoretical analysis and experimental results show that the proposed loop structure can track degraded signals (i.e., 18 dB-Hz with a very narrow loop bandwidth (i.e., 0.5 Hz and a TCXO clock.

  1. Design and Performance Evaluation of a Dual Antenna Joint Carrier Tracking Loop.

    Science.gov (United States)

    Guo, Wenfei; Lin, Tao; Niu, Xiaoji; Shi, Chuang; Zhang, Hongping

    2015-10-01

    In order to track the carrier phases of Global Navigation Satellite Systems (GNSS) signals in signal degraded environments, a dual antenna joint carrier tracking loop is proposed and evaluated. This proposed tracking loop processes inputs from two antennas, namely the master antenna and the slave antenna. The master antenna captures signals in open-sky environments, while the slave antenna capture signals in degraded environments. In this architecture, a Phase Lock Loop (PLL) is adopted as a master loop to track the carrier phase of the open-sky signals. The Doppler frequency estimated by this master loop is utilized to assist weak carrier tracking in the slave loop. As both antennas experience similar signal dynamics due to satellite motion and clock frequency variations, a much narrower loop bandwidth and possibly a longer coherent integration can be adopted to track the weak signals in slave channels, by utilizing the Doppler aid from master channels. PLL tracking performance is affected by the satellite/user dynamics, clock instability, and thermal noise. In this paper, their impacts on the proposed phase tracking loop are analyzed and verified by both simulation and field data. Theoretical analysis and experimental results show that the proposed loop structure can track degraded signals (i.e., 18 dB-Hz) with a very narrow loop bandwidth (i.e., 0.5 Hz) and a TCXO clock.

  2. Research on the technologies of conformal phased array antenna%共形相控阵天线的技术研究

    Institute of Scientific and Technical Information of China (English)

    伏浩; 李小浩; 李会莲

    2014-01-01

    Phased array antenna technology has been applied widely and developed rapidly in the fields of radar, communication, electronic warfare and navigation. Conformal phased array antenna technology is the focus of development of the phased array antenna. The development of foreign countries about conformal phased array antenna is introduced, the antenna array and pattern integration and beam forming of conformal phased array antenna are briefly discussed in this paper.%相控阵天线技术在雷达、通信、电子战、导航等领域获得了广泛应用和高速发展,共形相控阵天线是相控阵天线发展的重点之一。文章介绍了共形相控阵天线国外发展现状,进而探讨了共形相控阵的天线阵型,方向图综合及波束形成技术体制等关键技术。

  3. SPS-ALPHA: The First Practical Solar Power Satellite via Arbitrarily Large PHased Array Project

    Data.gov (United States)

    National Aeronautics and Space Administration — SPS-ALPHA (Solar Power Satellite via Arbitrarily Large Phased Array) is a novel, bio-mimetic approach to the challenge of space solar power. If successful, this...

  4. Phased Array GNSS Antenna for the FORMOSAT-7/COSMIC-2 Radio Occultation Mission

    Science.gov (United States)

    Turbiner, Dmitry; Young, Larry E.; Meehan, Tom K.

    2012-01-01

    Future GNSS remote sensing instruments such as the TriG receiver require more capable antennas than those flown on missions such as COSMIC. To maximize the number of ionospheric and atmospheric profiles, the TriG receiver will be capable of tracking legacy and new GPS signals such as L5, L2C and L1C; GLONASS CDMA and Galileo E1 and E5a. There has been an in-house effort at JPL to develop a set of antennas that would provide excellent Radio Occultations performance as well as navigation and ionospheric profiling. This effort is on-going but near completion for the manufacture and delivery of a set of flight antennas for the FORMOSAT-7/COSMIC-2 mission.

  5. Phased Array GNSS Antenna for the FORMOSAT-7/COSMIC-2 Radio Occultation Mission

    Science.gov (United States)

    Turbiner, Dmitry; Young, Larry E.; Meehan, Tom K.

    2012-01-01

    Future GNSS remote sensing instruments such as the TriG receiver require more capable antennas than those flown on missions such as COSMIC. To maximize the number of ionospheric and atmospheric profiles, the TriG receiver will be capable of tracking legacy and new GPS signals such as L5, L2C and L1C; GLONASS CDMA and Galileo E1 and E5a. There has been an in-house effort at JPL to develop a set of antennas that would provide excellent Radio Occultations performance as well as navigation and ionospheric profiling. This effort is on-going but near completion for the manufacture and delivery of a set of flight antennas for the FORMOSAT-7/COSMIC-2 mission.

  6. Designing Adaptive Linear Array Antenna to Achieve Pattern Steering Optimization by Phase-Amplitude Perturbations Using Genetic Algorithms

    Institute of Scientific and Technical Information of China (English)

    HSUChaohsing; CHENTsongyi; PanJengshyang

    2005-01-01

    In this paper, a phase-amplitude perturbation method of an adaptive array factor based on the genetic algorithm is proposed. The design for an optimal beam pattern of an adaptive antenna is able to not only suppress interference by placing nulls at the directions of the interfering sources but also provide a maximized main lobe in the direction of the desired signal, i.e., to maximizethe Signal interference ratio (SIR). In order to achieve this goal, a kind of new convergent skill called the two-way convergent method for genetic algorithms is proposed. The phase-amplitude perturbation method is applied to realize the optimal beam pattern of an adaptively linear array antenna. The Genetic algorithms are applied to find the optimal phase-amplitude weighting vector of adaptive array factor. An optimal beam pattern of linear array is derived by phase-amplitude perturbations using a genetic algorithm. Computer simulation result is given to demonstrate the effectiveness of the proposed method.

  7. Automatic phase control in solar power satellite systems

    Science.gov (United States)

    Lindsey, W. C.; Kantak, A. V.

    1978-01-01

    Various approaches to the problem of generating, maintaining and distributing a coherent, reference phase signal over a large area are suggested, mathematically modeled and analyzed with respect to their ability to minimize: phase build-up, beam diffusion and beam steering phase jitter, cable length, and maximize power transfer efficiency. In addition, phase control configurations are suggested which alleviate the need for layout symmetry.

  8. Simulating Global AeroMACS Airport Ground Station Antenna Power Transmission Limits to Avoid Interference With Mobile Satellite Service Feeder Uplinks

    Science.gov (United States)

    Wilson, Jeffrey D.

    2013-01-01

    The Aeronautical Mobile Airport Communications System (AeroMACS), which is based upon the IEEE 802.16e mobile wireless standard, is expected to be implemented in the 5091 to 5150 MHz frequency band. As this band is also occupied by Mobile Satellite Service feeder uplinks, AeroMACS must be designed to avoid interference with this incumbent service. The aspects of AeroMACS operation that present potential interference are under analysis in order to enable the definition of standards that assure that such interference will be avoided. In this study, the cumulative interference power distribution at low Earth orbit from transmitters at global airports was simulated with the Visualyse Professional software. The dependence of the interference power on antenna distribution, gain patterns, duty cycle, and antenna tilt was simulated. As a function of these parameters, the simulation results are presented in terms of the limitations on transmitter power from global airports required to maintain the cumulative interference power under the established threshold.

  9. Space communication link propagation data for selected cities within the multiple beam and steerable antenna coverage areas of the advanced communications technology satellite

    Science.gov (United States)

    Manning, Robert M.

    1988-01-01

    Rain attenuation propagation data for 68 cities within the coverage area of the multiple beam and steerable antennas of the Advanced Communications Technology Satellite (ACTS) are presented. These data provide the necessary data base for purposes of communication link power budgeting and rain attenuation mitigation controller design. These propagation parameters are derived by applying the ACTS Rain Attenuation Prediction Model to these 68 locations. The propagation parameters enumerated in tabular form for each location are as follows: (1) physical description of the link and location (e.g., latitude, longitude, antenna elevation angle, etc.), link availability versus attenuation margin (also in graphical form), fading time across fade depths of 3, 5, 8, and 15 dB versus fade duration, and required fade control response time for controller availabilities of 99.999, 99.99, 99.9, and 99 percent versus sub-threshold attenuation levels. The data for these specific locations can be taken to be representative of regions near these locations.

  10. Powers synthesis of array antennas using the continuation method on far field phase distribution

    NARCIS (Netherlands)

    Castaldi, G.; Gerini, G.

    2002-01-01

    We present a technique, based on the continuation method, to face power synthesis problems for array antennas. By using the least squares method (LSM), the power synthesis problem reduces to the minimization of an objective functional, which represents the square of the distance between the required

  11. Phased array antenna integrated with a frequency selective surface: Theory and experiments

    NARCIS (Netherlands)

    Monni, S.; Llombart Juan, N.; Neto, A.; Gerini, G.

    2003-01-01

    A modeling tool is described to characterize the array antennas integrated with frequency selective surfaces by means of a multimode equivalent network approach applied to infinite periodic structures. The theoretical formulation of the problem is presented in this paper together with the numerical

  12. Element failure correction for a large monopulse phased array antenna with active amplitude weighting

    NARCIS (Netherlands)

    Keizer, W.P.M.N.

    2007-01-01

    Recently a new method is introduced to synthesize low sidelobe patterns for planar array antennas with a periodic element arrangement. The method makes use of the property that for a planar array with periodic spacing of the elements, an inverse Fourier transform relationship exists between the arra

  13. Multiple Interference Cancellation Performance for GPS Receivers with Dual-Polarized Antenna Arrays

    Directory of Open Access Journals (Sweden)

    Moeness G. Amin

    2008-11-01

    Full Text Available This paper examines the interference cancellation performance in global positioning system (GPS receivers equipped with dual-polarized antenna arrays. In dense jamming environment, different types of interferers can be mitigated by the dual-polarized antennas, either acting individually or in conjunction with other receiver antennas. We apply minimum variance distorntionless response (MVDR method to a uniform circular dual-polarized antenna array. The MVDR beamformer is constructed for each satellite. Analysis of the eigenstructures of the covariance matrix and the corresponding weight vector polarization characteristics are provided. Depending on the number of jammers and jammer polarizations, the array chooses to expend its degrees of freedom to counter the jammer polarization or/and use phase coherence to form jammer spatial nulls. Results of interference cancellations demonstrate that applying multiple MVDR beamformers, each for one satellite, has a superior cancellation performance compared to using only one MVDR beamformer for all satellites in the field of view.

  14. 相控阵天线全光移相网络%Optical phase-shifting networks for phased array antenna

    Institute of Scientific and Technical Information of China (English)

    苏君; 邱琪; 史双瑾

    2011-01-01

    采用全光移相网络的光控相控阵天线具有使空间波束实现宽带宽角扫描的优势.传统相控阵天线受电移相网络的自身特性限制,瞬时应用带宽有限.系统分析了典型全光移相网络的技术特点,以及各个技术合适的应用方向和方案.%Optical phased array antenna based on optical phase-shifting networks continues to be an important challenge today, despite the advances made in beam squint-free scan for ultra-wideband signals. The traditional optical phased array antenna, described as characteristics limit of electronic phase-shifting networks, is beginning to provide low instantaneous bandwidth. In this paper, we systematically analyze the technical characteristics of typical optical phase-shifting networks and discuss some of the appropriate application domain of various networks.

  15. Solid-state retrodirective phased array concepts for microwave power transmission from Solar Power Satellite

    Science.gov (United States)

    Schroeder, K. G.; Petroff, I. K.

    1980-01-01

    Two prototype solid-state phased array systems concepts for potential use in the Solar Power Satellite are described. In both concepts, the beam is centered on the rectenna by means of phase conjugation of a pilot signal emanating from the ground. Also discussed is on-going solid-state amplifier development.

  16. Highly tunable ultra-narrow-resonances with optical nano-antenna phased arrays in the infrared

    CERN Document Server

    Li, Shi-Qiang; Guo, Peijun; Buchholz, D Bruce; Qiu, Ziwei; Ketterson, John B; Ocola, Leonidas E; Sakoda, Kazuaki; Chang, Robert P H

    2014-01-01

    We report our recent development in pursuing high Quality-Factor (high-Q factor) plasmonic resonances, with vertically aligned two dimensional (2-D) periodic nanorod arrays. The 2-D vertically aligned nano-antenna array can have high-Q resonances varying arbitrarily from near infrared to terahertz regime, as the antenna resonances of the nanorod are highly tunable through material properties, the length of the nanorod, and the orthogonal polarization direction with respect to the lattice surface,. The high-Q in combination with the small optical mode volume gives a very high Purcell factor, which could potentially be applied to various enhanced nonlinear photonics or optoelectronic devices. The 'hot spots' around the nanorods can be easily harvested as no index-matching is necessary. The resonances maintain their high-Q factor with the change of the environmental refractive index, which is of great interest for molecular sensing.

  17. New three-phase polymer-ceramic composite materials for miniaturized microwave antennas

    Science.gov (United States)

    Zhang, Li; Zhang, Jie; Yue, Zhenxing; Li, Longtu

    2016-09-01

    Unique polymer-ceramic composites for microwave antenna applications were prepared via melt extrusion using high-density polyethylene (HDPE) as the matrix and low-density polyethylene (LDPE) coated BaO-Nd2O3-TiO2 (BNT) ceramic-powders as the filler. By incorporating LDPE into the composites via a coating route, high ceramic-powder volume content (up to 50 vol%) could be achieved. The composites exhibited good microwave dielectric and thermomechanical behaviors. As BNT ceramic content increased from 10 vol% to 50 vol%, the permittivity of the composites increased from 3.45 (9 GHz) to 11.87 (7 GHz), while the dielectric loss remained lower than 0.0016. Microstrip antennas for applications in global positioning systems (GPS) were designed and fabricated from the composites containing 50 vol% BNT ceramics. The results indicate that the composites that have suitable permittivity and low dielectric loss are promising candidates for applications in miniaturized microwave devices, such as antennas.

  18. Phase Compensation Sensor for Ranging Consistency in Inter-Satellite Links of Navigation Constellation

    Science.gov (United States)

    Meng, Zhijun; Yang, Jun; Guo, Xiye; Hu, Mei

    2017-01-01

    The performance of the global navigation satellite system (GNSS) can be enhanced significantly by introducing the inter-satellite links (ISL) of a navigation constellation. In particular, the improvement of the position, velocity, and time accuracy, and the realization of autonomous functions require the ISL distance measurement data as the original input. For building a high-performance ISL, the ranging consistency between navigation satellites becomes a crucial problem to be addressed. Considering the frequency aging drift and the relativistic effect of the navigation satellite, the frequency and phase adjustment (FPA) instructions for the 10.23 MHz must be injected from the ground station to ensure the time synchronization of the navigation constellation. Moreover, the uncertainty of the initial phase each time the onboard clock equipment boots also results in a pseudo-range offset. In this Ref., we focus on the influence of the frequency and phase characteristics of the onboard clock equipment on the ranging consistency of the ISL and propose a phase compensation sensor design method for the phase offset. The simulation and experimental results show that the proposed method not only realized a phase compensation for the pseudo-range jitter, but, when the 1 PPS (1 pulse per second) falls in the 10.23 MHz skip area, also overcomes the problem of compensating the ambiguous phase by directly tracking the 10.23 MHz to ensure consistency in the ranging. PMID:28245572

  19. System overview on electromagnetic compensation for reflector antenna surface distortion

    Science.gov (United States)

    Acosta, R. J.; Zaman, A. J.; Terry, J. D.

    1993-01-01

    The system requirements and hardware implementation for electromagnetic compensation of antenna performance degradations due to thermal effects was investigated. Future commercial space communication antenna systems will utilize the 20/30 GHz frequency spectrum and support very narrow multiple beams (0.3 deg) over wide angle field of view (15-20 beamwidth). On the ground, portable and inexpensive very small aperture terminals (VSAT) for transmitting and receiving video, facsimile and data will be employed. These types of communication system puts a very stringent requirement on spacecraft antenna beam pointing stability (less than .01 deg), high gain (greater than 50 dB) and very lowside lobes (less than -25 dB). Thermal analysis performed on the advanced communication technology satellite (ACTS) has shown that the reflector surfaces, the mechanical supporting structures and metallic surfaces on the spacecraft body will distort due thermal effects from a varying solar flux. The antenna performance characteristics (e.g., pointing stability, gain, side lobe, etc.) will degrade due to thermal distortion in the reflector surface and supporting structures. Specifically, antenna RF radiation analysis has shown that pointing error is the most sensitive antenna performance parameter to thermal distortions. Other antenna parameters like peak gain, cross polarization level (beam isolation), and side lobe level will also degrade with thermal distortions. In order to restore pointing stability and in general antenna performance several compensation methods were proposed. In general these compensation methods can be classified as being either of mechanical or electromagnetic type. This paper will address only the later one. In this approach an adaptive phased array antenna feed is used to compensate for the antenna performance degradation. Extensive work has been devoted to demonstrate the feasibility of adaptive feed compensation on space communication antenna systems. This

  20. Effects of atmospheric turbulence on microwave and millimeter wave satellite communications systems. [attenuation statistics and antenna design

    Science.gov (United States)

    Devasirvatham, D. M. J.; Hodge, D. B.

    1981-01-01

    A model of the microwave and millimeter wave link in the presence of atmospheric turbulence is presented with emphasis on satellite communications systems. The analysis is based on standard methods of statistical theory. The results are directly usable by the design engineer.

  1. Group delay variations of GPS transmitting and receiving antennas

    Science.gov (United States)

    Wanninger, Lambert; Sumaya, Hael; Beer, Susanne

    2017-09-01

    GPS code pseudorange measurements exhibit group delay variations at the transmitting and the receiving antenna. We calibrated C1 and P2 delay variations with respect to dual-frequency carrier phase observations and obtained nadir-dependent corrections for 32 satellites of the GPS constellation in early 2015 as well as elevation-dependent corrections for 13 receiving antenna models. The combined delay variations reach up to 1.0 m (3.3 ns) in the ionosphere-free linear combination for specific pairs of satellite and receiving antennas. Applying these corrections to the code measurements improves code/carrier single-frequency precise point positioning, ambiguity fixing based on the Melbourne-Wübbena linear combination, and determination of ionospheric total electron content. It also affects fractional cycle biases and differential code biases.

  2. Analysis of double stub tuner control stability in a phased array antenna with strong cross-coupling

    Energy Technology Data Exchange (ETDEWEB)

    Wallace, G.M., E-mail: wallaceg@mit.edu [MIT Plasma Science and Fusion Center, Cambridge, MA 02139 (United States); Hillairet, J. [CEA-IRFM, Saint-Paul-lez-Durance (France); Koert, P.; Lin, Y.; Shiraiwa, S.; Wukitch, S.J. [MIT Plasma Science and Fusion Center, Cambridge, MA 02139 (United States)

    2014-11-15

    Highlights: • A novel method for reducing reflection coefficients for LHCD launchers is proposed and evaluated. • Numerical models of antenna behavior with stub tuning are analyzed. • The system is found to be stable under most realistic operating conditions. - Abstract: Active stub tuning with a fast ferrite tuner (FFT) has greatly increased the effectiveness of fusion ion cyclotron range of frequency (ICRF) systems (50–100 MHz) by allowing for the antenna system to respond dynamically to changes in the plasma load impedance such as during the L–H transition or edge localized modes (ELMs). A high power waveguide double-stub tuner is under development for use with the Alcator C-Mod lower hybrid current drive (LHCD) system at 4.6 GHz. The amplitude and relative phase shift between adjacent columns of an LHCD antenna are critical for control of the launched n{sub ||} spectrum. Adding a double-stub tuning network will perturb the phase and amplitude of the forward wave particularly if the unmatched reflection coefficient is high. This effect can be compensated by adjusting the phase of the low power microwave drive for each klystron amplifier. Cross-coupling of the reflected power between columns of the launcher must also be considered. The problem is simulated by cascading a scattering matrix for the plasma provided by a linear coupling model with the measured launcher scattering matrix and that of the FFTs. The solution is advanced in an iterative manner similar to the time-dependent behavior of the real system. System performance is presented under a range of edge density conditions from under-dense to over-dense and a range of launched n{sub ||}. Simulations predict power reflection coefficients (Γ{sup 2}) of less than 1% with no contamination of the n{sub ||} spectrum. Instability of the FFT tuning network can be problematic for certain plasma conditions and relative phasings, but reducing the control gain of the FFT network stabilizes the system.

  3. Reconfigurable Antennas for High Data Rate Multi-beam Communication Systems

    Science.gov (United States)

    Bernhard, Jennifer T.; Michielssen, Eric

    2005-01-01

    High-speed (2-100 Mb/sec) wireless data communication - whether land- or satellite-based - faces a major challenge: high error rates caused by interference and unpredictable environments. A planar antenna system that can be reconfigured to respond to changing conditions has the potential to dramatically improve data throughput and system reliability. Moreover, new planar antenna designs that reduce array size, weight, and cost can have a significant impact on terrestrial and satellite communication system performance. This research developed new individually-reconfigurable planar antenna array elements that can be adjusted to provide multiple beams while providing increased scan angles and higher aperture efficiency than traditional diffraction-limited arrays. These new elements are microstrip spiral antennas with specialized tuning mechanisms that provide adjustable radiation patterns. We anticipate that these new elements can be used in both large and small arrays for inter-satellite communication as well as tracking of multiple mobile surface-based units. Our work has developed both theoretical descriptions as well as experimental prototypes of the antennas in both single element and array embodiments. The technical summary of the results of this work is divided into six sections: A. Cavity model for analysis and design of pattern reconfigurable antennas; B. Performance of antenna in array configurations for broadside and endfire operation; C. Performance of antenna in array configurations for beam scanning operation; D. Simulation of antennas in infinite phased arrays; E. Demonstration of antenna with commercially-available RF MEMS switches; F. Design of antenna MEMS switch combinations for direct simultaneous fabrication.

  4. Low Cost High Performance Phased Array Antennas with Beam Steering Capabilities

    Science.gov (United States)

    2009-12-01

    licensed use limited to: UNIV OF HAWAII LIBRARY. Downloaded on June 18.2010 at 22:19:39 UTC from IEEE Xplore Restrictions apply. 4W IEEE MICROWAVE...39 UTC from IEEE Xplore . Restrictions apply. ISKANDER el at.: COAXIAL CONTINUOUS TRANSVERSE STUB (CTS) ARRAY 4’) I S1 l(simjlated) = • and S11...22:19:39 UTC from IEEE Xplore Restrictions apply 2180 IEEE TRANSACTIONS ON ANTENNAS AND PROPAGATION. VOL. 52. NO 8. AUGUST 2004 1 4 1 2 1 0 08

  5. The CARMA Paired Antenna Calibration System: Atmospheric Phase Correction for Millimeter Wave Interferometry and its Application to Mapping the Ultraluminous Galaxy Arp 193

    CERN Document Server

    Zauderer, B Ashley; Vogel, Stuart N; Carpenter, John M; Peréz, Laura M; Lamb, James W; Woody, David P; Bock, Douglas C -J; Carlstrom, John E; Culverhouse, Thomas L; Curley, Roger; Leitch, Erik M; Plambeck, Richard L; Pound, Marc W; Marrone, Daniel P; Muchovej, Stephen J; Mundy, Lee G; Teng, Stacy H; Teuben, Peter J; Volgenau, Nikolaus H; Wright, Melvyn C H; Wu, Dalton

    2014-01-01

    Phase fluctuations introduced by the atmosphere are the main limiting factor in attaining diffraction limited performance in extended interferometric arrays at millimeter and submillimeter wavelengths. We report the results of C-PACS, the Combined Array for Research in Millimeter-Wave Astronomy Paired Antenna Calibration System. We present a systematic study of several hundred test observations taken during the 2009-2010 winter observing season where we utilize CARMA's eight 3.5-m antennas to monitor an atmospheric calibrator while simultaneously acquiring science observations with 6.1-m and 10.4-m antennas on baselines ranging from a few hundred meters to ~2 km. We find that C-PACS is systematically successful at improving coherence on long baselines under a variety of atmospheric conditions. We find that the angular separation between the atmospheric calibrator and target source is the most important consideration, with consistently successful phase correction at CARMA requiring a suitable calibrator locate...

  6. Analysis of L5 phase variations in GPS IIF satellites by the raw observation PPP approach

    Science.gov (United States)

    Liu, Sha; Becker, Matthias

    2015-04-01

    GPS modernization along with Glonass modernization and the emerging Galileo and Compass system has been highly anticipated by every GNSS user since several years. The third civilian L5 signal transmitted by the modernized GPS satellites brings us to the GNSS multi-frequency era. The first GPS IIF satellite was launched in May 2010, until now there are eight block IIF satellites in service and the remaining four IIF satellites are planned to be launched by 2016. The introduction of the third frequency to GPS and the usage of advanced atomic clocks not only provide the users more possibilities but also enable higher positioning accuracy. Nevertheless phase variations are found on the new L5 observation of GPS SVN62. Further investigations suggest that the variations of this satellite are strongly dependent on the satellite inner temperature variation caused by sun illumination. Besides achieving precise positioning accuracy, PPP is also frequently used as a tool to analyze and evaluate various GNSS errors, for instance, tropospheric delays and receiver clock errors. Other than with differential GNSS, it is possible to separate different errors and to identify the error sources with PPP. Conventional PPP is based on the ionosphere-free linear combination, in order to eliminate the first-order ionospheric delays. However only dual frequencies can be used to build ionosphere-free linear combination, which leads to the waste of the information on the third frequency. Furthermore, the frequency dependent errors can not be separated and traced. A new PPP approach that avoids using any linear combination is proposed recently, which is called the raw observation PPP. One advantage of the raw observation PPP approach is that data of all frequencies and all GNSS systems can be jointly used. In addition, the frequency dependent errors are possible to be separated, identified and analyzed. In this paper the raw observation PPP is utilized to analyze the phase variations on L5

  7. Antennas for light and plasmons

    NARCIS (Netherlands)

    Dikken, Dirk Jan Willem

    2015-01-01

    Antennas have been used for over a century as emitters, scatterers and receivers of electromagnetic waves. All wireless communication devices, such as radio, mobile phones and satellite communication are strongly dependent on the capability of an antenna to localize propagating electromagnetic waves

  8. Phase Compensation Sensor for Ranging Consistency in Inter-Satellite Links of Navigation Constellation.

    Science.gov (United States)

    Meng, Zhijun; Yang, Jun; Guo, Xiye; Hu, Mei

    2017-02-24

    Theperformanceoftheglobalnavigationsatellitesystem(GNSS)canbeenhancedsignificantly by introducing the inter-satellite links (ISL) of a navigation constellation. In particular, the improvement of the position, velocity, and time accuracy, and the realization of autonomous functions require the ISL distance measurement data as the original input. For building a high-performance ISL, the ranging consistency between navigation satellites becomes a crucial problem to be addressed. Considering the frequency aging drift and the relativistic effect of the navigation satellite, the frequency and phase adjustment (FPA) instructions for the 10.23 MHz must be injected from the ground station to ensure the time synchronization of the navigation constellation. Moreover, the uncertainty of the initial phase each time the onboard clock equipment boots also results in a pseudo-range offset. In this Ref., we focus on the influence of the frequency and phase characteristics of the onboard clock equipment on the ranging consistency of the ISL and propose a phase compensation sensor design method for the phase offset. The simulation and experimental results show that the proposed method not only realized a phase compensation for the pseudo-range jitter, but, when the 1 PPS (1 pulse per second) falls in the 10.23 MHz skip area, also overcomes the problem of compensating the ambiguous phase by directly tracking the 10.23 MHz to ensure consistency in the ranging.

  9. Ultra-thin single-layer transparent geometrical phase gradient metasurface and its application to high-gain circularly-polarized lens antenna

    Science.gov (United States)

    Li, Tang-Jing; Liang, Jian-Gang; Li, Hai-Peng; Liu, Ya-Qiao

    2016-09-01

    A new method to design an ultra-thin high-gain circularly-polarized antenna system with high efficiency is proposed based on the geometrical phase gradient metasurface (GPGM). With an accuracy control of the transmission phase and also the high transmission amplitude, the GPGM is capable of manipulating an electromagnetic wave arbitrarily. A focusing transmission lens working at Ku band is well optimized with the F/D of 0.32. A good focusing effect is demonstrated clearly by theoretical calculation and electromagnetic simulation. For further application, an ultra-thin single-layer transmissive lens antenna based on the proposed focusing metasurface operating at 13 GHz is implemented and launched by an original patch antenna from the perspective of high integration, simple structure, and low cost. Numerical and experimental results coincide well, indicating the advantages of the antenna system, such as a high gain of 17.6 dB, the axis ratio better than 2 dB, a high aperture efficiency of 41%, and also a simple fabrication process based on the convenient print circuit board technology. The good performance of the proposed antenna indicates promising applications in portable communication systems. Project supported by the National Natural Science Foundation of China (Grant No. 61372034).

  10. Trans-Pacific HDR Satellite Communications Experiment Phase-2 Project Plan and Experimental Network

    Science.gov (United States)

    Hsu, Eddie; Kadowaki, Naoto; Yoshimura, Naoko; Takahashi, Takashi; Yoshikawa, Makoto; Bergman, Larry; Bhasin, Kul

    2000-01-01

    The trans-Pacific high data rate (TP-HDR) satellite communications experiment was proposed at the Japan-U.S. Cooperation in Space (JUCS) Program Workshop held in Hawaii in 1993 and remote high definition video post-production was demonstrated as the first phase trial. ATM-based 45 Mbps trans-Pacific link was established in the first phase, and the following experiments with 155 Mbps was planned as the phase 2. This paper describes the experimental network configuration and project plan of TP-HDR experiment phase 2. Additional information is provided in the original.

  11. 基于通信卫星的非对称圆环毫米波微带天线%Asymmetric ring millimeter-wave microstrip antenna based on communications satellite

    Institute of Scientific and Technical Information of China (English)

    张宁; 张霞

    2013-01-01

    针对毫米波微带天线的特点,设计了一种可用于通信卫星的天线.该天线在辐射贴片的顶部开了个渐变的缝隙并在天线体上方放置矩形槽形成耦合,从而达到展宽天线带宽的效果,在天线单元的基础上分析了该天线的阵列形式.采用基于时域有限积分算法的CST三维电磁仿真软件对该设计进行仿真,分析结果表明在设计的工作频带范围内,该天线具有较好的带宽范围和较高的增益,且结构小巧简单,具有较高实用价值.%An antenna for communications satellites based on characteristics of millimeter wave microstrip antenna is researched.To broadening the bandwidth,the antenna opened a gradient in the gap at the top of the radiation patch and at the top of the antenna body placed rectangular groove where is formed coupling.Analysis on the basis of the antenna elements,the antenna array have achieved.Simulation of the design using 3D electromagnetic simulation software CST which is used on time domain finite integration algorithm,the analysis results show that in the design of the work within the frequency range the antenna having a better bandwidth range,high directional gain,simple structure and easy to be fabricated in the design band.

  12. Robust Precoding Design for Multibeam Downlink Satellite Channel with Phase Uncertainty

    OpenAIRE

    Gharanjik, Ahmad; Shankar, Bhavani; Arapoglou, Pantelis-Daniel; Bengtsson, Mats

    2015-01-01

    In this work, we study the design of a precoder on the user downlink of a multibeam satellite channel. The variations in channel due to phase noise introduced by on-board oscillators and the long round trip delay result in outdated channel information at the transmitter. The phase uncertainty is modelled and a robust design framework is formulated based on availability and power constraints. The optimization problem is cast into the convex paradigm after approximations and the benefits of the...

  13. Study on In-Orbit Test Methods for Antenna Coverage of Geostationary Communication Satellites%同步轨道通信卫星天线覆盖图在轨测试方法

    Institute of Scientific and Technical Information of China (English)

    许国庆; 毛新宏; 贺中人; 杨丽

    2013-01-01

    The purpose of in-orbit tests on the antenna pattern of geostationary communication satellites is to verify consistency of the stationed satellite footprint with the designed coverage area,and to analyze the influence of antenna thermal deformation caused by solar radiation on the coverage characteristics.This paper describes relevant in-orbit test methods,e.g.maneuvering satellite attitude method,moving antenna platform method and using movable earth station method,for three types of antennas used on satellites,fixed shaped antenna,zone beam antenna and movable spot beam antenna.A solution by using transponder telemetry parameters and multiple stations in maneuvering satellite attitude is studied and a challenge of saving precious fuel and measuring as much pattern cuts as possible is effectively resolved.In-orbit tests are performed on a fixed shaped antenna and a movable spot beam antenna of a real satellite.The test results show good agreement with theoretical characteristics,proving feasibility of the methods.Finally,the measurement uncertainty of the solution is analyzed.%同步轨道通信卫星天线覆盖图在轨测试的目的是检验卫星入轨后上下行覆盖图与设计覆盖区域的一致性,以及太阳照射产生的天线热变形等因素对覆盖特性的影响.针对卫星上常用的固定赋形波束天线、区域波束天线和可移动点波束天线等类型的星载天线在轨测试问题,分析了几种在轨测试方法的原理,包括偏置卫星姿态法、转动天线平台法以及使用移动测量站的方法,提出了偏置卫星姿态法中融合转发器遥测参数判决和多站联合在轨测试的解决方案,有效解决了既要节省宝贵的燃料又要尽可能测量多条切线方向图的工程难题.对真星的固定赋形波束天线和可移动点波束天线进行了在轨测试,测试结果与实际特性吻合很好,验证了方法的可行性.最后,针对融合遥测参数判决的多站联合偏置

  14. Wideband Antennas for Modern Radar Systems

    OpenAIRE

    Ren, Yu-Jiun; Lai, Chieh-Ping

    2010-01-01

    In this chapter, the basics of the antenna and phased array are reviewed and different wideband antennas for modern radar systems are presented. The concepts of the radome and frequency selective surface are also reviewed. The main contents include important parameters of the antenna, and theory and design consideration of the array antenna. Various wideband antennas are introduced and their performances are demonstrated, including: (1) for the phased array radar, the slotted waveguide array ...

  15. Mobile multimedia antenna systems for station wagons and the achievable diversity effectiveness obtained by analysis of virtual test drives

    Science.gov (United States)

    Hopf, J. F.; Lindenmeier, H. K.; Reiter, L. M.

    2003-04-01

    For modern cars, antennas are required for AM reception, FM and TV diversity reception, weatherband reception (USA), terrestrial digital radio, remote control functions, keyless entry, mobile phone for all worldwide used systems, GPS, and in the future, satellite broadcast radio services. Those services cover the frequency range from 150 kHz up to 2.4 GHz. Such kind of a multiantenna system developed for station wagons is presented in this paper. The obtainable FM and TV diversity effectiveness is discussed for several types of antenna arrangements in detail. This value is the number of fictitious completely decorrelated antenna signals and is obtained by virtual test drives. The characteristic of the respective antennas under test is introduced in the software as antenna pattern, measured or calculated with respect to amplitude and phase. During the computer analysis the car with the antennas is driven virtually through a Rayleigh field scenario with desired and undesired signals.

  16. Conformal and Spectrally Agile Ultra Wideband Phased Array Antenna for Communication and Sensing

    Science.gov (United States)

    Novak, M.; Alwan, Elias; Miranda, Felix; Volakis, John

    2015-01-01

    There is a continuing need for reducing size and weight of satellite systems, and is also strong interest to increase the functional role of small- and nano-satellites (for instance SmallSats and CubeSats). To this end, a family of arrays is presented, demonstrating ultra-wideband operation across the numerous satellite communications and sensing frequencies up to the Ku-, Ka-, and Millimeter-Wave bands. An example design is demonstrated to operate from 3.5-18.5 GHz with VSWR2 at broadside, and validated through fabrication of an 8 x 8 prototype. This design is optimized for low cost, using Printed Circuit Board (PCB) fabrication. With the same fabrication technology, scaling is shown to be feasible up to a 9-49 GHz band. Further designs are discussed, which extend this wideband operation beyond the Ka-band, for instance from 20-80 GHz. Finally we will discuss recent efforts in the direct integration of such arrays with digital beamforming back-ends. It will be shown that using a novel on-site coding architecture, orders of magnitude reduction in hardware size, power, and cost is accomplished in this transceiver.

  17. 大型网状可展开天线的动力学与控制研究进展%Advance of Dynamics and Control of the Satellite with Large Mesh Deployable Antenna

    Institute of Scientific and Technical Information of China (English)

    刘丽坤; 周志成; 郑钢铁; 田强

    2014-01-01

    随着卫星移动通信技术的迅猛发展,为了提高卫星天线增益,普遍采用大型网状可展开抛物面天线。由于该类天线具有质量惯量大、展开过程耗时长、低刚度等特点,其展开过程和在轨正常工作期间,对卫星的动力学和姿态控制有较大影响。文章首先对大型网状可展开天线的特点及其对卫星动力学与控制的影响进行介绍,然后对大型网状可展开天线带来的动力学与控制相关问题进展进行了综述,包括:大型网状可展开天线展开状态动力学建模、展开状态试验验证、展开过程动力学建模、展开过程姿态控制及在轨天线指向控制等。最后对采用大型网状可展开天线的动力学与控制研究方向进一步需深入开展的工作提出了建议。%With the development of mobile communication technology ,the large deployable parabolic mesh reflectors are wildly used to improve the antenna gain . Considering the large inertia , long-period deployment , and low stiffness properties , these antennae have a great influence on the dynamics and control of the satellites . Firstly , the structural characteristics and its influences on the dynamic and control of the whole-satellite were introduced for the large mesh deployable antenna . Secondly , the dynamic and control problems were discussed , such as dynamic modeling of the deployed antenna , verification method of the deployed dynamic model , multi-body dynamics of the deploying antenna , deploying-process attitude control , and pointing control of the antenna , and so on . Finally , the prospects of the dynamics and control of the satellite with large deployable antenna were presented .

  18. Development of an L-band Conformal Phased Array Antenna%L频段共形相控阵天线研制

    Institute of Scientific and Technical Information of China (English)

    梁宇宏

    2016-01-01

    To meet the requirement of an airborne system,the analysis and design process of a conformal phased array antenna is presented,and also the quasi-yagi antenna unit,the height of which is nearly 0. 14 wavelengths is designed. The software HFSS is used to simulate the antenna unit and conformal phased ar-ray. An L-band conformal phased array antenna is developed,which consists of array antenna,beamforming network and beam controller. Array antenna is realized by 4 antenna units,which is mounted on the confor-mal structure of plane’ s nose. The test results of the conformal phased array antenna show that the gain of sum beam >10 dBi in all scanning range,meanwhile the low side lobe is achieved,and null depth of differ-ence beam <-20 dB.%为满足机载系统的需要,给出了共形相控阵天线的分析和设计过程,同时研制了一种高度仅为0.14波长的准八木天线单元。利用三维电磁仿真软件HFSS对天线单元和共形相控阵进行了仿真设计,并研制了一套L频段共形相控阵天线。该天线由天线阵面、波束形成网络和波控器等构成。天线阵面由4个天线单元组成,共形安装在机头上。经实际测试,共形相控阵天线阵面的和波束在扫描范围内增益大于10 dBi,并具有较低的副瓣电平;差波束零深小于-20 dB。

  19. Fourpoint antenna

    OpenAIRE

    2003-01-01

    Wideband antennas with omnidirectional coverage have both military and commercial applications. In one embodiment, the Planar Inverted Cone Antenna (PICA) is composed of a single flat element vertically mounted above a ground plane. A geometry of Planar Inverted Cone Antenna (PICA) is based on the conventional circular-disc antenna with trimmed top part having the shape of a planar-inverted cone, in a second embodiment, the Fourpoint antenna also provides balanced impedance over the operating...

  20. Positioning reduction in the real-time phase of Chang'E-2 satellite

    Science.gov (United States)

    Li, JinLing; Liu, Li; Zheng, WeiMin; Sun, ZhongMiao

    2012-02-01

    The precision of VLBI tracking delays and the positioning reduction results during the real-time tracking phase of the Chang'E-2 satellite are statistically analyzed. The application of the positioning reduction to the real-time monitoring of pivotal arcs of the Chang'E-2 satellite is discussed. The technical specifications of the tests of tracking and control systems in X-band are estimated and evaluated via the positioning reduction method. Useful methodology and software are prepared and practical experience in engineering and technology is accumulated for the follow-up lunar and deep space explorations of China.

  1. Communication satellite technology trends

    Science.gov (United States)

    Cuccia, Louis

    1986-01-01

    A chronology of space-Earth interconnectivity is presented. The Advanced Communications Technology Satellite (ACTS) system, Land Mobile Satellite, space-Earth antennas, impact of antenna size on coverage, intersatellite links are outlined. This presentation is represented by graphs and charts only.

  2. Single Band Helical Antenna in Axial Mode

    Directory of Open Access Journals (Sweden)

    Parminder Singh

    2012-11-01

    Full Text Available Helical antennas have been widely used in a various useful applications, due to their low weight and low profile conformability, easy and cheap realization.Radiation properties of this antenna are examined both theoretically and experimentally. In this paper, an attempt has been made to investigate new helical antenna structure for Applications. CST MWS Software is used for the simulation and design calculations of the helical antennas. The axial ratio, return loss, VSWR, Directivity, gain, radiation pattern is evaluated. Using CST MWS simulation software proposed antenna is designed/simulated and optimized. The antenna exhibits a single band from 0 GHz to 3 GHz for GPS and several satellite applications

  3. Multi-fidelity optimization design of phased array radar antenna%相控阵雷达天线多保真度优化设计

    Institute of Scientific and Technical Information of China (English)

    虞跨海; 段世忠; 李朝伟; 周树平

    2012-01-01

    研究了某型相控阵雷达天线多保真度优化设计技术.基于代理模型,提出了天线单元优化、阵列优化和近似模型的分层次多保真度优化方法,以提高计算效率;采用KS包络函数将多目标问题转化为单目标函数;以雷达天线几何模型参数为设计变量,以提高雷达天线电磁性能为目标,以温度、应力、变形等为约束,在Isight平台下建立了某型相控阵雷达天线的多学科设计优化系统,实现了雷达天线阵列的多学科设计优化,在满足传热、强度等学科约束的条件下,提高了雷达天线的电磁性能.%Multi-fidelity design optimization methodology for a phased array radar antenna was studied. Based on agent model, a multi-level multi-fidelity optimization methodology, including antenna u-nite optimization, array optimization and approximate model was proposed to improve the computational efficiency. KS (kreisselmeier-steinhauser) envelop function method was exploited to transform the multi-objective into a single function. A phased array radar antenna design optimization procedure was established by employing the commercial software Isight, geometry model parameters of radar antenna as design variables, electromagnetic properties as objectives, and temperature, stress, and deformation as constraints. Multidisciplinary design optimization of the radar antenna array was completed, and electromagnetic properties of the radar antenna were improved.

  4. Phased-Array Antenna Beam Squinting Related to Frequency Dependency of Delay Circuits

    NARCIS (Netherlands)

    Garakoui, S.K.; Klumperink, E.A.M.; Nauta, B.; Vliet, F.E. van

    2011-01-01

    Practical time delay circuits do not have a perfectly linear phase-frequency characteristic. When these delay circuits are applied in a phased-array system, this frequency dependency shows up as a frequency dependent beam direction (“beam squinting”). This paper quantifies beam squinting for a linea

  5. 47 CFR 25.209 - Antenna performance standards.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Antenna performance standards. 25.209 Section... SATELLITE COMMUNICATIONS Technical Standards § 25.209 Antenna performance standards. (a) The gain of any antenna to be employed in transmission from an earth station in the fixed-satellite service shall lie...

  6. Design of multi-layer circularly polarized microstrip antenna in satellite navigation receiver system%卫星导航接收机系统中的多层圆极化微带天线设计

    Institute of Scientific and Technical Information of China (English)

    王喜龙; 魏昆

    2015-01-01

    Several circularly polarized receiving antennas with different frequency in small space are placed on satellite naviga⁃tion receiver system. The double⁃deck circularly polarized antenna,which receives signals from the GPS with L1 frequency point and L2 frequency point is studied and designed to save space. The double⁃deck antenna consists of two separate single feed point antenna,which is working at L1 frequency range and L2 frequency range independently,right⁃hand circular polarization and left⁃hand circular polarization of the antenna is working as receiving antenna and sending antenna. It′s easy to debug and in⁃stall since the antenna is processed with 4 mm thickness composite material. The simulation analysis and optimization proved that the designed antenna with high gain,excellent polarization and qualifies bandwidth requirement,and it is suitable for satel⁃lite navigation receiver system application.%卫星导航接收机系统有时需要在较小的区域中放置多个不同频率的圆极化接收天线。通过研究并设计出一种GPS的L1和L2双频点双层叠放圆极化天线,可以在很大程度上节约空间。该天线上下层是两个独立的单馈点天线,可以分别在L1和L2频段独立工作,分别为右旋圆极化和左旋圆极化,可作接收天线和发射天线。天线由厚度为4 mm的复合材料加工而成,调试和组装均比较方便。经过仿真分析优化,设计的天线增益较高,极化特性优良,带宽满足要求,完全适合于卫星导航接收机系统的应用。

  7. An FSS-Backed 20/30 GHz Circularly Polarized Reflectarray for a Shared Aperture L- and Ka-Band Satellite Communication Antenna

    DEFF Research Database (Denmark)

    Smith, Thomas Gunst; Gothelf, Ulrich; Kim, Oleksiy S.

    2014-01-01

    A shared aperture antenna for simultaneous operation at L- (1525 to 1661 MHz) and Ka-band (19.7 to 20.2 GHz and 29.5 to 30.0 GHz) is demonstrated. This stacked antenna consists of a Ka-band reflectarray antenna with a frequency selective surface (FSS) ground-plane above an L-band patch array...... antenna. The reflectarray is based on the concentric dual split-loop element backed by a concentric dual-loop FSS element. The reflectarray comprises 80 × 80 elements and it is printed on a 40 ×40 cm2 Rogers 5880 substrate, while the L-band antenna is a 2 × 2 patch array. The reflectarray antenna has been...

  8. An offset-fed 20/30 GHz dual-band circularly polarized reflectarray antenna

    DEFF Research Database (Denmark)

    Smith, Thomas Gunst; Vesterdal, Niels; Gothelf, Ulrich;

    2013-01-01

    A dual-frequency circularly polarized offset reflectarray antenna for Ka-band satellite communication is presented. The reflectarray is designed using the concentric dual split-loop element which enables full 360° phase adjustment simultaneously in two separate frequency bands. The elements have...

  9. Turbulent phase noise on asymmetric two-way ground-satellite coherent optical links

    Science.gov (United States)

    Robert, Clélia; Conan, Jean-Marc; Wolf, Peter

    2015-10-01

    Bidirectional ground-satellite laser links suffer from turbulence-induced scintillation and phase distortion. We study how turbulence impacts on coherent detection capacity and on the associated phase noise that restricts clock transfer precision. We evaluate the capacity to obtain a two-way cancellation of atmospheric effects despite the asymmetry between up and down link that limits the link reciprocity. For ground-satellite links, the asymmetry is induced by point-ahead angle and possibly the use, for the ground terminal, of different transceiver diameters, in reception and emission. The quantitative analysis is obtained thanks to refined end-to-end simulations under realistic turbulence and wind conditions as well as satellite cinematic. Simulations make use of the reciprocity principle to estimate both down and up link performance from wave-optics propagation of descending plane waves. These temporally resolved simulations allow characterising the coherent detection in terms of time series of heterodyne efficiency for different system parameters. We show Tip/Tilt correction on ground is mandatory at reception for the down link and as a pre-compensation of the up link. Good correlation between up and down phase noise is obtained even with asymmetric apertures of the ground transceiver and in spite of pointing ahead angle. The reduction to less than 1 rad2 of the two-way differential phase noise is very promising for clock transfer.

  10. Distributed MIMO Antenna Architecture for Wireless-over- Fiber Backhaul with Multicarrier Optical Phase Modulation

    DEFF Research Database (Denmark)

    Caballero Jambrina, Antonio; Wong, Shing-Wa; Zibar, Darko

    2011-01-01

    A novel optical phase-modulated wireless-over-fiber backhaul architecture for next generation cellular network is presented and experimentally demonstrated for high capacity wireless multicarrier uplink transmission on a single wavelength.......A novel optical phase-modulated wireless-over-fiber backhaul architecture for next generation cellular network is presented and experimentally demonstrated for high capacity wireless multicarrier uplink transmission on a single wavelength....

  11. Installing the antenna for STELLA

    CERN Multimedia

    1979-01-01

    The 3 metre diameter antenna for the STELLA satellite communication project is lowered into position on the roof of the Computer Building (see Weekly Bulletin 48/79 and CERN Courier 19 (1979) 444). STELLA stands for Satellite Transmission Experiment Linking Laboratories.

  12. APPLICATION OF VISION METROLOGY TO IN-ORBIT MEASUREMENT OF LARGE REFLECTOR ONBOARD COMMUNICATION SATELLITE FOR NEXT GENERATION MOBILE SATELLITE COMMUNICATION

    Directory of Open Access Journals (Sweden)

    M. Akioka

    2016-06-01

    Full Text Available Satellite for next generation mobile satellite communication service with small personal terminal requires onboard antenna with very large aperture reflector larger than twenty meters diameter because small personal terminal with lower power consumption in ground base requires the large onboard reflector with high antenna gain. But, large deployable antenna will deform in orbit because the antenna is not a solid dish but the flexible structure with fine cable and mesh supported by truss. Deformation of reflector shape deteriorate the antenna performance and quality and stability of communication service. However, in case of digital beam forming antenna with phased array can modify the antenna beam performance due to adjustment of excitation amplitude and excitation phase. If we can measure the reflector shape precisely in orbit, beam pattern and antenna performance can be compensated with the updated excitation amplitude and excitation phase parameters optimized for the reflector shape measured every moment. Softbank Corporation and National Institute of Information and Communications Technology has started the project "R&D on dynamic beam control technique for next generation mobile communication satellite" as a contracted research project sponsored by Ministry of Internal Affairs and Communication of Japan. In this topic, one of the problem in vision metrology application is a strong constraints on geometry for camera arrangement on satellite bus with very limited space. On satellite in orbit, we cannot take many images from many different directions as ordinary vision metrology measurement and the available area for camera positioning is quite limited. Feasibility of vision metrology application and general methodology to apply to future mobile satellite communication satellite is to be found. Our approach is as follows: 1 Development of prototyping simulator to evaluate the expected precision for network design in zero order and first order

  13. Application of Vision Metrology to In-Orbit Measurement of Large Reflector Onboard Communication Satellite for Next Generation Mobile Satellite Communication

    Science.gov (United States)

    Akioka, M.; Orikasa, T.; Satoh, M.; Miura, A.; Tsuji, H.; Toyoshima, M.; Fujino, Y.

    2016-06-01

    Satellite for next generation mobile satellite communication service with small personal terminal requires onboard antenna with very large aperture reflector larger than twenty meters diameter because small personal terminal with lower power consumption in ground base requires the large onboard reflector with high antenna gain. But, large deployable antenna will deform in orbit because the antenna is not a solid dish but the flexible structure with fine cable and mesh supported by truss. Deformation of reflector shape deteriorate the antenna performance and quality and stability of communication service. However, in case of digital beam forming antenna with phased array can modify the antenna beam performance due to adjustment of excitation amplitude and excitation phase. If we can measure the reflector shape precisely in orbit, beam pattern and antenna performance can be compensated with the updated excitation amplitude and excitation phase parameters optimized for the reflector shape measured every moment. Softbank Corporation and National Institute of Information and Communications Technology has started the project "R&D on dynamic beam control technique for next generation mobile communication satellite" as a contracted research project sponsored by Ministry of Internal Affairs and Communication of Japan. In this topic, one of the problem in vision metrology application is a strong constraints on geometry for camera arrangement on satellite bus with very limited space. On satellite in orbit, we cannot take many images from many different directions as ordinary vision metrology measurement and the available area for camera positioning is quite limited. Feasibility of vision metrology application and general methodology to apply to future mobile satellite communication satellite is to be found. Our approach is as follows: 1) Development of prototyping simulator to evaluate the expected precision for network design in zero order and first order 2) Trial

  14. Analysis of double stub tuner control stability in a many element phased array antenna with strong cross-coupling

    Energy Technology Data Exchange (ETDEWEB)

    Wallace, G. M.; Fitzgerald, E.; Johnson, D. K.; Kanojia, A. D.; Koert, P.; Lin, Y.; Murray, R.; Shiraiwa, S.; Terry, D. R.; Wukitch, S. J. [MIT Plasma Science and Fusion Center, Cambridge, MA 02139 (United States); Hillairet, J. [CEA-IRFM, Saint-Paul-lez-Durance (France)

    2014-02-12

    Active stub tuning with a fast ferrite tuner (FFT) allows for the system to respond dynamically to changes in the plasma impedance such as during the L-H transition or edge localized modes (ELMs), and has greatly increased the effectiveness of fusion ion cyclotron range of frequency systems. A high power waveguide double-stub tuner is under development for use with the Alcator C-Mod lower hybrid current drive (LHCD) system. Exact impedance matching with a double-stub is possible for a single radiating element under most load conditions, with the reflection coefficient reduced from Γ to Γ{sup 2} in the “forbidden region.” The relative phase shift between adjacent columns of a LHCD antenna is critical for control of the launched n{sub ∥} spectrum. Adding a double-stub tuning network will perturb the phase of the forward wave particularly if the unmatched reflection coefficient is high. This effect can be compensated by adjusting the phase of the low power microwave drive for each klystron amplifier. Cross-coupling of the reflected power between columns of the launcher must also be considered. The problem is simulated by cascading a scattering matrix for the plasma provided by a linear coupling model with the measured launcher scattering matrix and that of the FFTs. The solution is advanced in an iterative manner similar to the time-dependent behavior of the real system. System performance is presented under a range of edge density conditions from under-dense to over-dense and a range of launched n{sub ∥}.

  15. Plasma Antenna

    OpenAIRE

    N M Vijay

    2014-01-01

    The fundamental base of plasma antenna is the use of an ionized medium as a conductor. The plasma antenna is a radiofrequency antenna formed by a plasma columns, Filaments or sheets, which are excited by a surface wave. The relevance of this device is how rapidly it can be turned on and off, only applying an electrical pulse. Besides its wide carrier frequency, the great directivity and controllable antenna shape. Otherwise a disadvantage is that it needs energy to be ionized....

  16. Quasi-analytical synthesis of continuous phase correcting structures to increase the directivity of circularly polarized Fabry-Perot resonator antennas

    Energy Technology Data Exchange (ETDEWEB)

    Afzal, Muhammad U., E-mail: muhammad.afzal@mq.edu.au; Esselle, Karu P. [Department of Engineering, Faculty of Science and Engineering, Macquarie University, Sydney, NSW 2109 (Australia)

    2015-06-07

    This paper presents a quasi-analytical technique to design a continuous, all-dielectric phase correcting structures (PCSs) for circularly polarized Fabry-Perot resonator antennas (FPRAs). The PCS has been realized by varying the thickness of a rotationally symmetric dielectric block placed above the antenna. A global analytical expression is derived for the PCS thickness profile, which is required to achieve nearly uniform phase distribution at the output of the PCS, despite the non-uniform phase distribution at its input. An alternative piecewise technique based on spline interpolation is also explored to design a PCS. It is shown from both far- and near-field results that a PCS tremendously improves the radiation performance of the FPRA. These improvements include an increase in peak directivity from 22 to 120 (from 13.4 dBic to 20.8 dBic) and a decrease of 3 dB beamwidth from 41.5° to 15°. The phase-corrected antenna also has a good directivity bandwidth of 1.3 GHz, which is 11% of the center frequency.

  17. Non-standard antennas

    CERN Document Server

    Le Chevalier, Francois; Staraj, Robert

    2013-01-01

    This book aims at describing the wide variety of new technologies and concepts of non-standard antenna systems - reconfigurable, integrated, terahertz, deformable, ultra-wideband, using metamaterials, or MEMS,  etc, and how they open the way to a wide range of applications, from personal security and communications to multifunction radars and towed sonars, or satellite navigation systems, with space-time diversity on transmit and receive. A reference book for designers  in this lively scientific community linking antenna experts and signal processing engineers.

  18. Group Delay of High Q Antennas

    DEFF Research Database (Denmark)

    Bahramzy, Pevand; Pedersen, Gert Frølund

    2013-01-01

    become an issue, when working with high Q antennas, because of the steep phase shift over the frequency. In this paper, it is measured how large group delay variations can become, when going from a low Q antenna to a high Q antenna. The group delay of a low Q antenna is shown to be around 1.3 ns, whereas...... a high Q antenna has group delay of around 22 ns. It is due to this huge group delay variation characteristics of high Q antennas, that signal distortion might occur in the radio system with high Q antennas....

  19. Advanced two-way satellite frequency transfer by carrier-phase and carrier-frequency measurements

    Science.gov (United States)

    Fujieda, Miho; Gotoh, Tadahiro; Amagai, Jun

    2016-06-01

    Carrier-phase measurement is one of the ways to improve the measurement resolution of two-way satellite frequency transfer. We introduce two possible methods for carrier-phase measurement: direct carrier-phase detection identified by Two-Way Carrier-Phase (TWCP) and the use of carrier-frequency information identified by Two-Way Carrier Frequency (TWCF). We performed the former using an arbitrary waveform generator and an analog-to-digital sampler and the latter using a conventional modem. The TWCF measurement using the modem had a resolution of 10-13 and the result agreed with that obtained by GPS carrier-phase frequency transfer in a 1500 km baseline. The measurement accuracy may have been limited by the poor frequency resolution of the modem; however, the TWCF measurement was able to improve the stability of conventional two-way satellite frequency transfer. Additionally, we show that the TWCP measurement system has the potential to achieve a frequency stability of 10-17.

  20. An Overview of Antenna R&D Efforts in Support of NASA's Space Exploration Vision

    Science.gov (United States)

    Manning, Robert M.

    2007-01-01

    This presentation reviews the research and development work being conducted at Glenn Research Center in the area of antennas for space exploration. In particular, after reviewing the related goals of the agency, antenna technology development at GRC is discussed. The antennas to be presented are large aperture inflatable antennas, phased array antennas, a 256 element Ka-band antenna, a ferroelectric reflectarray antenna, multibeam antennas, and several small antennas.

  1. System and method for phase retrieval for radio telescope and antenna control

    Science.gov (United States)

    Dean, Bruce H. (Inventor)

    2013-01-01

    Disclosed herein are systems, methods, and non-transitory computer-readable storage media for radio phase retrieval. A system practicing the method gathers first data from radio waves associated with an object observed via a first aperture, gathers second data from radio waves associated with the object observed via an introduced second aperture associated with the first aperture, generates reduced noise data by incoherently subtracting the second data from the first data, and performs phase retrieval for the radio waves by modeling the reduced noise data using a single Fourier transform. The first and second apertures are at different positions, such as side by side. This approach can include determining a value Q which represents a ratio of wavelength times a focal ratio divided by pixel spacing. This information can be used to accurately measure and correct alignment errors or other optical system flaws in the apertures.

  2. Design for the Assessment and Policy Analysis of the Education Satellite Communications Demonstration. Phase 2 Final Report.

    Science.gov (United States)

    Syracuse Univ. Research Corp., NY. Educational Policy Research Center.

    The overall goal of the Education Satellite Communications Demonstration is to design a framework for the analysis of the potential utility of satellites to education in this country. Within this framework, Phase 2 sought to identify research which would be clearly related to educational goals that might be worthy of attainment. The entire…

  3. 可收展卫星天线用金属网技术研究进展%Advances on the Metal Gauzes in Drawing -in and Opening -up Satellite Antenna

    Institute of Scientific and Technical Information of China (English)

    赛兴鹏; 秦庆彦

    2011-01-01

    随着卫星通信技术的不断发展,对卫星天线的口径要求越来越大,收展工作特性要求越来越高,这使天线用金属网材料和成网技术得到了较快发展.文章介绍了国外可收展星载卫星天线的概况,分析了天线用金属网面材料、网面织构参数、成网技术的发展,以及我国金属网的研究和应用发展状况.%With the rapid development of the satellite communication techniques, the requirements for large bore size and high working performances of the satellite antenna are increasing. The metal gauzes materials and knitting techniques have progressed rapidly. The general situations of the drawing - in and opening- up satellite antenna are introduced in the present paper, including the metal gauzes materials,wire size parameters and knitting techniques. The paper also covers the achievements made in China on metal gauzes.

  4. Phase Error Modeling and Its Impact on Precise Orbit Determination of GRACE Satellites

    Directory of Open Access Journals (Sweden)

    Jia Tu

    2012-01-01

    Full Text Available Limiting factors for the precise orbit determination (POD of low-earth orbit (LEO satellite using dual-frequency GPS are nowadays mainly encountered with the in-flight phase error modeling. The phase error is modeled as a systematic and a random component each depending on the direction of GPS signal reception. The systematic part and standard deviation of random part in phase error model are, respectively, estimated by bin-wise mean and standard deviation values of phase postfit residuals computed by orbit determination. By removing the systematic component and adjusting the weight of phase observation data according to standard deviation of random component, the orbit can be further improved by POD approach. The GRACE data of 1–31 January 2006 are processed, and three types of orbit solutions, POD without phase error model correction, POD with mean value correction of phase error model, and POD with phase error model correction, are obtained. The three-dimensional (3D orbit improvements derived from phase error model correction are 0.0153 m for GRACE A and 0.0131 m for GRACE B, and the 3D influences arisen from random part of phase error model are 0.0068 m and 0.0075 m for GRACE A and GRACE B, respectively. Thus the random part of phase error model cannot be neglected for POD. It is also demonstrated by phase postfit residual analysis, orbit comparison with JPL precise science orbit, and orbit validation with KBR data that the results derived from POD with phase error model correction are better than another two types of orbit solutions generated in this paper.

  5. Multibeam Antennas Array Pattern Synthesis Using a Variational Method

    Directory of Open Access Journals (Sweden)

    F. T. Bendimerad

    2007-06-01

    Full Text Available In this paper a new method is described for multibeam antennas synthesis where both the amplitude and phase of each radiating element is a design variable. The developed optimization method made possible to solve the synthesis problem and to answer all the constraints imposed by the radiation pattern. Two approaches for visualizing satellite antenna radiation patterns are presented. Gain-level contours drawn over a geographical map gives clearest qualitative information. A three-dimensional (3D surface plot displays the qualitative shape of the radiation pattern more naturally. The simulations results have shown power, precision and speed of the variational method with respect to the constraints imposed on radiation pattern of the of multibeam antennas network.

  6. Berry phases and profiles of line wings and rainbow satellites induced by optical collisions

    Science.gov (United States)

    Ciuryło, R.; Szudy, J.; Baylis, W. E.

    2015-09-01

    The concept of Berry phase is included in an analysis of the intensity distribution in far wings of pressure-broadened spectral lines emitted or absorbed by atoms placed in an external cone-rotating electric field. Particular attention is focused on frequency regions where rainbow satellite bands appear. A classical-path treatment that employs the time-dependent Schrödinger equation is used to derive an expression for the line shape, and it uses a dipole transition moment calculated with quasimolecular wave functions given by the Berry version of the adiabatic approximation. It is found that in the presence of an external rotating electric field, the intensity distribution in far wings can be expressed in terms of the universal line shape function of the unified Franck-Condon theory once energy shifts due to Stark and Berry effects are taken into account. We show that the influence of Berry phase in the profiles of the far wings can be manifested either in the form of deviations of observed profiles from the quasistatic distribution or the appearance of additional features in the vicinity of the maximum of the rainbow satellite band. As an example, the modification of the rainbow satellite at 162.3 nm in the red wing of the self-broadened Lyman-α line of hydrogen, caused by an external rotating electric field, is considered.

  7. Antenna technology for advanced mobile communication systems

    Science.gov (United States)

    Rammos, Emmanuel; Roederer, Antoine; Rogard, Roger

    1988-01-01

    The onboard antenna front end is the key subsystem conditioning configuration and performance of mobile communication satellites. The objectives of this paper are to demonstrate this key role and to review L-band satellite antenna technology for earth coverage and regional applications. Multibeam arrays are first discussed, then unfurlable and inflatable reflector antennas are described. These technologies are now qualified in Europe for future mobile systems, for which the optimum choice of antenna technology has been found to be the key to efficient use of spectrum and power resources.

  8. Reconfigurable antenna pattern verification

    Science.gov (United States)

    Drexler, Jerome P. (Inventor); Becker, Robert C. (Inventor); Meyers, David W. (Inventor); Muldoon, Kelly P. (Inventor)

    2013-01-01

    A method of verifying programmable antenna configurations is disclosed. The method comprises selecting a desired antenna configuration from a plurality of antenna configuration patterns, with the selected antenna configuration forming at least one reconfigurable antenna from reconfigurable antenna array elements. The method validates the formation of the selected antenna configuration to determine antenna performance of the at least one reconfigurable antenna.

  9. Compact broadband 5-bit photonic true-time-delay module for phased-array antennas.

    Science.gov (United States)

    Fu, Z; Li, R; Chen, R T

    1998-04-01

    Photonic true-time-delay (TTD) lines offer many advantages over their electronic counterparts and are attracting more and more research effort. We demonstrate a device with 32 TTD lines (5-bit) based on substrate guided-wave propagation combined with slanted photopolymer volume phase gratings on a quartz substrate. System design, device fabrication, optimization of fan-out intensity uniformity, and device performance evaluation are addressed as well. The device has a measured bandwidth of up to 2.4 THz and a measured fan-out delay step of 50 ps. The fan-out beam intensity uniformity is within +/-10% . The packing density is 2.5 delay lines/cm(2), which is to our knowledge the highest demonstrated thus far.

  10. 连续相位变化毫米波衍射天线%Millimeter wave diffraction antenna based on continuous phase correction

    Institute of Scientific and Technical Information of China (English)

    陈鑫; 潘文武; 薛长江; 余川; 屈劲; 陈世韬; 施美友

    2012-01-01

    A Cassegrain phase-correcting Fresnel zone plate antenna has been designed based on the Fresnel principle and the Cas-segrain antenna design method. It consists of a suite of Fresnel zone continuous phase correcting concentric rings, and its diameter of aperture is 200 mm. Compared with the traditional paraboloid antenna, the Cassegrain Fresnel zone plate antenna has a flat and light structure. It precedes the discrete phase diffraction antenna in radiation performance. The simulation has been performed based on the physical optics method, and the test has been performed with the near-field scanning system. The test shows that, at 95 GHz the antenna has an efficiency of 65%. Its 3 dB beam widths are 0. 95° and 1. 05°, and its gain is 44. 1 dB.%基于菲涅尔原理及卡塞格伦天线设计方法,设计了一种口面直径为200 mm的卡赛格伦菲涅耳相位修正平面天线.天线采用连续相位修正方式,由一组同心菲涅耳相位修正圆环组成,与传统卡赛格伦抛物面天线相比,该天线具有平面化结构,大大减小了天线自身重量,天线辐射性能较离散相位衍射天线有大幅度提高.在95 GHz频率下,采用物理光学法进行仿真计算,并采用近场扫描系统进行了天线性能测试,天线3dB波束宽度分别为0.95°及1.05°,天线实测增益为44.1 dB,天线口面效率为65%.

  11. Out-of-plane reflection and refraction of light by anisotropic optical antenna metasurfaces with phase discontinuities.

    Science.gov (United States)

    Aieta, Francesco; Genevet, Patrice; Yu, Nanfang; Kats, Mikhail A; Gaburro, Zeno; Capasso, Federico

    2012-03-14

    Experiments on ultrathin anisotropic arrays of subwavelength optical antennas display out-of-plane refraction. A powerful three-dimensional (3D) extension of the recently demonstrated generalized laws of refraction and reflection shows that the interface imparts a tangential wavevector to the incident light leading to anomalous beams, which in general are noncoplanar with the incident beam. The refracted beam direction can be controlled by varying the angle between the plane of incidence and the antenna array.

  12. The ACTS multibeam antenna

    Science.gov (United States)

    Regier, Frank A.

    1992-01-01

    The Advanced Communications Technology Satellite (ACTS) to be launched in 1993 is briefly introduced. Its multibeam antenna, consisting of electrically similar 30 GHz receive and 20 GHz transmit offset Cassegrain systems, both utilizing orthogonal polarizations, is described. Dual polarization is achieved by using one feed assembly for each polarization in conjunction with nested front and back subreflectors, the gridded front subreflector acting as a window for one polarization and a reflector for the other. The antennas produce spot beams with approximately 0.3 degree beamwidth and gains of approximately 50 dbi. High surface accuracy and high edge taper produce low sidelobe levels and high cross-polarization isolation. A brief description is given of several Ka-band components fabricated for ACTS. These include multiflare antenna feedhorns, beam-forming networks utilizing latching ferrite waveguide switches, a 30 GHz HEMT low-noise amplifier and a 20 GHz TWT power amplifier.

  13. The ACTS multibeam antenna

    Science.gov (United States)

    Regier, Frank A.

    1992-06-01

    The Advanced Communications Technology Satellite (ACTS) to be launched in 1993 is briefly introduced. Its multibeam antenna, consisting of electrically similar 30 GHz receive and 20 GHz transmit offset Cassegrain systems, both utilizing orthogonal polarizations, is described. Dual polarization is achieved by using one feed assembly for each polarization in conjunction with nested front and back subreflectors, the gridded front subreflector acting as a window for one polarization and a reflector for the other. The antennas produce spot beams with approximately 0.3 degree beamwidth and gains of approximately 50 dbi. High surface accuracy and high edge taper produce low sidelobe levels and high cross-polarization isolation. A brief description is given of several Ka-band components fabricated for ACTS. These include multiflare antenna feedhorns, beam-forming networks utilizing latching ferrite waveguide switches, a 30 GHz HEMT low-noise amplifier and a 20 GHz TWT power amplifier.

  14. Frequency division multiplexed microwave and baseband digital optical fiber link for phased array antennas

    Science.gov (United States)

    Heim, Peter J.; McClay, C. Phillip

    1990-05-01

    A frequency-division multiplexed optical fiber link is described in which microwave (1-8 GHz) and baseband digital (1-10 Mb/s) signals are combined electrically and transmitted through a direct-modulation microwave optical link. The microwave signal does not affect bit error rate (BER) performance of the Manchester-coded baseband digital data link. The baseband digital signal affects microwave signal quality by generating second-order intermodulation noise. The intermodulation noise power density is found to be proportional to both the microwave input power and the digital input power, enabling the system to be modeled as a mixer (AM modulator). The conversion loss for the digital signal is approximately 68 dB for a 1-GHz microwave signal and is highly dependent on the microwave frequency, reaching a minimum value of 41 dB at 4.5 GHz, corresponding to the laser diode relaxation oscillation frequency. It is shown that Manchester coding on the digital link places the intermodulation noise peak away from the microwave signal, preventing degradation of close-carrier phase noise (<1 kHz offset). A direct trade-off between intermodulation noise and digital link margin is developed to project system performance.

  15. Frequency scanning microstrip antennas

    DEFF Research Database (Denmark)

    Danielsen, Magnus; Jørgensen, Rolf

    1979-01-01

    The principles of using radiating microstrip resonators as elements in a frequency scanning antenna array are described. The resonators are cascade-coupled. This gives a scan of the main lobe due to the phase-shift in the resonator in addition to that created by the transmission line phase...

  16. A distributed array antenna system

    Science.gov (United States)

    Shaw, R.; Kovitz, J.

    1986-01-01

    The Space Station communication system will use microwave frequency radio links to carry digitized information from sender to receiver. The ability of the antenna system to meet stringent requirements on coverage zones, multiple users, and reliability will play an important part in the overall multiple access communication system. This paper will describe the configuration of a multibeam conformal phased array antenna and the individual microwave integrated components incoporated into this antenna system.

  17. Transparent antennas for solar cell integration

    Science.gov (United States)

    Yasin, Tursunjan

    Transparent patch antennas are microstrip patch antennas that have a certain level of optical transparency. Highly transparent patch antennas are potentially suitable for integration with solar panels of small satellites, which are becoming increasingly important in space exploration. Traditional patch antennas employed on small satellites compete with solar cells for surface area. However, a transparent patch antenna can be placed directly on top of solar cells and resolve the issue of competing for limited surface real estate. For such an integration, a high optical transparency of the patch antenna is required from the solar cells' point of view. On the other hand, the antenna should possess at least acceptable radiation properties at the same time. This dissertation focuses on some of the most important concerns from the perspective of small satellite applications. For example, an optimization method to simultaneously improve both optical transparency and radiation efficiency of the antenna is studied. Active integrated antenna design method is extended to meshed patch applications in an attempt to improve the overall power efficiency of the front end communication subsystem. As is well known, circular polarization is immune from Faraday rotation effect in the ionosphere and thus can avoid a 3-dB loss in geo-satellite communication. Therefore, this research also aims to present design methods for circularly polarized meshed patch antennas. Moreover, a meshed patch antenna capable of supporting a high communication data rate is investigated. Lastly, other types of transparent patch antennas are also analyzed and compared to meshed patches. In summary, many properties of transparent patch antennas are examined in order to meet different design requirements.

  18. Space debris proximity analysis in powered and orbital phases during satellite launch

    Science.gov (United States)

    Bandyopadhyay, Priyankar; Sharma, R. K.; Adimurthy, V.

    2004-01-01

    This paper describes the methodology of the space debris proximity analysis in powered and orbital phase at the time of a satellite launch. The details of the SPADEPRO analysis package, developed for this purpose, are presented. It consists of modules which provide the functions related to ephemeris generation and reconstruction of primary object (launch vehicle or its payload upon insertion), determination of close approaches with resident space objects, computation of the state vector variance of the primary and the secondary objects to represent the knowledge uncertainty, and computation of the collision risk given the variance. This has been successfully applied during the recent launches of the Indian Space Research Organization.

  19. Geodetic Secor Satellite

    Science.gov (United States)

    1974-06-01

    simple, and had low-power lem. 17 14. Satellite Orientation . The satellite was designed to maintain a constant relationship between the antenna...the same satellite orientation . Further considerations were Th oscillations, however, when higher orbital ranges (500-2500 nautical miles) -, 3 a

  20. Cup Cylindrical Waveguide Antenna

    Science.gov (United States)

    Acosta, Roberto J.; Darby, William G.; Kory, Carol L.; Lambert, Kevin M.; Breen, Daniel P.

    2008-01-01

    The cup cylindrical waveguide antenna (CCWA) is a short backfire microwave antenna capable of simultaneously supporting the transmission or reception of two distinct signals having opposite circular polarizations. Short backfire antennas are widely used in mobile/satellite communications, tracking, telemetry, and wireless local area networks because of their compactness and excellent radiation characteristics. A typical prior short backfire antenna contains a half-wavelength dipole excitation element for linear polarization or crossed half-wavelength dipole elements for circular polarization. In order to achieve simultaneous dual circular polarization, it would be necessary to integrate, into the antenna feed structure, a network of hybrid components, which would introduce significant losses. The CCWA embodies an alternate approach that entails relatively low losses and affords the additional advantage of compactness. The CCWA includes a circular cylindrical cup, a circular disk subreflector, and a circular waveguide that serves as the excitation element. The components that make it possible to obtain simultaneous dual circular polarization are integrated into the circular waveguide. These components are a sixpost polarizer and an orthomode transducer (OMT) with two orthogonal coaxial ports. The overall length of the OMT and polarizer (for the nominal middle design frequency of 2.25 GHz) is about 11 in. (approximately equal to 28 cm), whereas the length of a commercially available OMT and polarizer for the same frequency is about 32 in. (approximately equal to 81 cm).

  1. Reconfigurable antennas

    CERN Document Server

    Bernhard, Jennifer

    2007-01-01

    This lecture explores the emerging area of reconfigurable antennas from basic concepts that provide insight into fundamental design approaches to advanced techniques and examples that offer important new capabilities for next-generation applications. Antennas are necessary and critical components of communication and radar systems, but sometimes their inability to adjust to new operating scenarios can limit system performance. Making antennas reconfigurable so that their behavior can adapt with changing system requirements or environmental conditions can ameliorate or eliminate these restricti

  2. Microstrip Antenna

    OpenAIRE

    Anuj Mehta

    2015-01-01

    Abstract This article presents an overview of the microstrip patch antenna and its design techniques. Basically a microstrip patch antenna comprises of a trace of copper or any other metal of any geometry on one side of a standard printed circuit board substrate with other side grounded. The antenna is fed using various feeding techniques like coaxial strip line aperture coupling or proximity coupling techniques. The working principle and the radiation mechanism have also been described. The ...

  3. 20/30 GHz dual-band circularly polarized reflectarray antenna based on the concentric dual split-loop element

    DEFF Research Database (Denmark)

    Smith, Thomas Gunst; Vesterdal Larsen, Niels; Vesterager Gothelf, Ulrich

    2012-01-01

    A concentric dual split-loop element is designed and investigated for reflectarray antenna design in the emerging 20 GHz and 30 GHz Ka-band satellite communication spectrum. The element is capable of providing adjustment of the phase of reflection coefficients for circular plane waves in two...

  4. Antenna Measurement

    OpenAIRE

    Picard, Dominique

    2010-01-01

    Currently it is possible to measure all the characteristics of an antenna with a good accuracy. Far-field ranges do not have a very good accuracy, due to parasitic reflections for the outdoor ranges and because of the limited distance between the source antenna and the tested antenna for the indoor ranges. The compact range allows one to obtain a direct farfield cut in a relatively short time. The near-field techniques are the most accurate and the most convenient for global antenna radiation...

  5. Antenna toolkit

    CERN Document Server

    Carr, Joseph

    2006-01-01

    Joe Carr has provided radio amateurs and short-wave listeners with the definitive design guide for sending and receiving radio signals with Antenna Toolkit 2nd edition.Together with the powerful suite of CD software, the reader will have a complete solution for constructing or using an antenna - bar the actual hardware! The software provides a simple Windows-based aid to carrying out the design calculations at the heart of successful antenna design. All the user needs to do is select the antenna type and set the frequency - a much more fun and less error prone method than using a con

  6. 箭载共形相控阵卫星数据链通信仿真研究%The communication simulation of data link between satellite and rocket-borne conformal phased array

    Institute of Scientific and Technical Information of China (English)

    曾国奇; 李思吟; 韦志棉; 饶赣新

    2012-01-01

    Using the relay satellite as a communications relay, the rocket and the relay satellite are within mutual sight during the whole launch of the launch vehicle. Without any shelter, uninterrupted measurement and control can be achieved on the launch vehicle. In this paper, the transmission losses of the data link between satellite and rocket-borne conformal phased array satellite were analyzed, such as free-space attenuation, atmospheric attenuation, flame attenuation, polarization decay, antenna pointing error loss, and attenuation induced by rain. And the safety margin of the data link between satellite and rocket-borne conformal phased array satellite is simulated during the rocket flight in the S-band.%利用中继星作为通信中继,在运载火箭发射的全程中火箭与中继星都视线可见,不存在遮挡,可以实现对运载火箭的不间断测控.文章对运载火箭共形相控阵卫星数据链传输过程中的自由空间衰减、大气衰减、火焰衰减、极化衰减、天线指向误差损耗、雨衰等进行了分析,并对火箭飞行过程中,S波段箭载共形相控阵卫星数据链的安全裕度进行了仿真.

  7. 卫星导航专利分析报告之三──接收机四臂螺旋天线%The Third Report for Satellite Navigation Patent Analysis--quadrifilar helix antenna for receiver

    Institute of Scientific and Technical Information of China (English)

    程小亮; 丰学民; 王海波

    2015-01-01

    As the critical part for satellite navigation receiver receiving satellite signal, antenna affects directly the navigation and positioning effects with its performance. As the second part of series reports for receiver antenna patent analysis and on the basis of mass exact data statistics, this paper studies the characteristics of principal applicants and origin countries deeply, selects the important patents from Sarantel Inc. which is an important company in industry, and shows comprehensively the technique status and development trends in future in the art by means of technical efifciency analysis.%天线作为卫星导航接收机接收卫星信号的关键部分,其性能直接影响到卫星导航接收机的导航和定位效果。本文作为接收机天线专利分析报告系列的第三部分,以大量精确的数据统计为基础,深入研究了四臂螺旋天线的主要申请人及来源国特点,对行业重点企业萨恩特尔公司的重要专利进行筛选,并借助技术功效分析将该领域的技术现状和未来发展趋势给予全面展现。

  8. A Review of Antennas for Picosatellite Applications

    Directory of Open Access Journals (Sweden)

    Abdul Halim Lokman

    2017-01-01

    Full Text Available Cube Satellite (CubeSat technology is an attractive emerging alternative to conventional satellites in radio astronomy, earth observation, weather forecasting, space research, and communications. Its size, however, poses a more challenging restriction on the circuitry and components as they are expected to be closely spaced and very power efficient. One of the main components that will require careful design for CubeSats is their antennas, as they are needed to be lightweight, small in size, and compact or deployable for larger antennas. This paper presents a review of antennas suitable for picosatellite applications. An overview of the applications of picosatellites will first be explained, prior to a discussion on their antenna requirements. Material and antenna topologies which have been used will be subsequently discussed prior to the presentation of several deployable configurations. Finally, a perspective and future research work on CubeSat antennas will be discussed in the conclusion.

  9. Subpixel Accuracy Analysis of Phase Correlation Shift Measurement Methods Applied to Satellite Imagery

    Directory of Open Access Journals (Sweden)

    S.M. Badwai

    2013-01-01

    Full Text Available the key point of super resolution process is the accurate measuring of sub-pixel shift. Any tiny error in measuring such shift leads to an incorrect image focusing. In this paper, methodology of measuring sub-pixel shift using Phase correlation (PC are evaluated using different window functions, then modified version of (PC method using high pass filter (HPF is introduced . Comprehensive analysis and assessment of (PC methods shows that different natural features yield different shift measurements. It is concluded that there is no universal window function for measuring shift; it mainly depends on the features in the satellite images. Even the question of which window is optimal of particular feature is generally remains open. This paper presents the design of a method for obtaining high accuracy sub pixel shift phase correlation using (HPF.The proposed method makes the change in the different locations that lack of edges easy.

  10. Galactic Halo Stars in Phase Space A Hint of Satellite Accretion?

    CERN Document Server

    Brook, C B; Gibson, B K; Flynn, C; Brook, Chris B.; Kawata, Daisuke; Gibson, Brad K.; Flynn, Chris

    2003-01-01

    The present day chemical and dynamical properties of the Milky Way bear the imprint of the Galaxy's formation and evolutionary history. One of the most enduring and critical debates surrounding Galactic evolution is that regarding the competition between ``satellite accretion'' and ``monolithic collapse''; the apparent strong correlation between orbital eccentricity and metallicity of halo stars was originally used as supporting evidence for the latter. While modern-day unbiased samples no longer support the claims for a significant correlation, recent evidence has been presented by Chiba & Beers (2000,AJ,119,2843) for the existence of a minor population of high-eccentricity metal-deficient halo stars. It has been suggested that these stars represent the signature of a rapid (if minor) collapse phase in the Galaxy's history. Employing velocity- and integrals of motion-phase space projections of these stars, coupled with a series of N-body/Smoothed Particle Hydrodynamic (SPH) chemodynamical simulations, we...

  11. Low-profile natural and metamaterial antennas analysis methods and applications

    CERN Document Server

    Nakano, Hisamatsu

    2017-01-01

    This book presents the full range of low-profile antennas that use novel elements and take advantage of new concepts in antenna implementation, including metamaterials. Typically formed by constructing lattices of simple elements, metamaterials possess electromagnetic properties not found in naturally occurring materials, and show great promise in a number of low-profile antenna implementations. Introductory chapters define various natural and metamaterial-based antennas and provide the fundamentals of writing computer programs based on the method of moments (MoM) and the finite-difference time-domain method (FDTDM). Chapters then discuss low-profile natural antennas classified into base station antennas, mobile card antennas, beam-forming antennas, and satellite-satellite and earth-satellite communications antennas. Final chapters look at various properties of low-profile metamaterial-based ant nnas, revealing the strengths and limitations of the metamaterial-based straight line antenna (metaline antenna), m...

  12. Metamaterial-based "sabre" antenna

    Science.gov (United States)

    Hafdallah Ouslimani, Habiba; Yuan, Tangjie; Kanane, Houcine; Priou, Alain; Collignon, Gérard; Lacotte, Guillaume

    2014-05-01

    The "sabre" antenna is an array of two monopole elements, vertically polarized with omnidirectional radiation patterns, and placed on either side of a composite material on the tail of an airplane. As an in-phase reflector plane, the antenna uses a compact dual-layer high-impedance surface (DL-HIS) with offset mushroom-like Sivenpiper square shape unit cells. This topology allows one to control both operational frequency and bandgap width, while reducing the total height of the antenna to under λ0/36. The designed antenna structure has a wide bandwidth higher than 24% around 1.4 GHz. The measurements and numerical simulations agree very well.

  13. Analysis of phase noise and cnr degradation of externally generated lo signal in lnb for ku-band dvb-s systems by heterodyning two lasers

    NARCIS (Netherlands)

    Khan, M.R.H.; Burla, M.; Roeloffzen, C.G.H.; Marpaung, D.A.I.; Etten, van W.

    2009-01-01

    We investigate the externally generation of an LO signal by optical heterodyning, which is then distributed to each of the mixers at every antenna element of a phased array antenna used for standard DVB-S (digital Video Broadcasting-Satellite) reception system. The system1 is presented in Figure 1.

  14. Small X-Band Oscillator Antennas

    Science.gov (United States)

    Lee, Richard Q.; Miranda, Felix A.; Clark, Eric B.; Wilt, David M.; Mueller, Carl H.; Kory, Carol L.; Lambert, Kevin M.

    2009-01-01

    A small, segmented microstrip patch antenna integrated with an X-band feedback oscillator on a high-permittivity substrate has been built and tested. This oscillator antenna is a prototype for demonstrating the feasibility of such devices as compact, low-power-consumption building blocks of advanced, lightweight, phased antenna arrays that would generate steerable beams for communication and remotesensing applications.

  15. Motion estimation in wide band synthetic aperture sonar based on the raw echo data using the method of displaced phase center antenna

    Institute of Scientific and Technical Information of China (English)

    JIANG Xiaokui; SUN Chao; FANG Jie

    2003-01-01

    Phase errors in synthetic aperture sonar (SAS) imaging must be reduced to less than one eighth of a wavelength so as to avoid image destruction. Most of the phase errors occur as a result of platform motion errors, for example, sway yaw and surge that are the most important error sources. The phase error of a wide band synthetic aperture sonar is modeled and solutions to sway yaw and surge motion estimation based on the raw sonar echo data with a Displaced Phase Center Antenna (DPCA) method are proposed and their implementations are detailed in this paper. It is shown that the sway estimates can be obtained from the correlation lag and phase difference between the returns at coincident phase centers. An estimate of yaw is also possible if such a technique is applied to more than one overlapping phase center positions. Surge estimates can be obtained by identifying pairs of phase centers with a maximum correlation coefficient. The method works only if the platform velocity is low enough such that a number of phase centers from adjacent pings overlap.

  16. Certified dual-corrected radiation patterns of phased antenna arrays by offline–online order reduction of finite-element models

    Energy Technology Data Exchange (ETDEWEB)

    Sommer, A., E-mail: a.sommer@lte.uni-saarland.de; Farle, O., E-mail: o.farle@lte.uni-saarland.de; Dyczij-Edlinger, R., E-mail: edlinger@lte.uni-saarland.de

    2015-10-15

    This paper presents a fast numerical method for computing certified far-field patterns of phased antenna arrays over broad frequency bands as well as wide ranges of steering and look angles. The proposed scheme combines finite-element analysis, dual-corrected model-order reduction, and empirical interpolation. To assure the reliability of the results, improved a posteriori error bounds for the radiated power and directive gain are derived. Both the reduced-order model and the error-bounds algorithm feature offline–online decomposition. A real-world example is provided to demonstrate the efficiency and accuracy of the suggested approach.

  17. 47 CFR 25.205 - Minimum angle of antenna elevation.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Minimum angle of antenna elevation. 25.205... SATELLITE COMMUNICATIONS Technical Standards § 25.205 Minimum angle of antenna elevation. (a) Earth station antennas shall not normally be authorized for transmission at angles less than 5° measured from the...

  18. Phase 2 Final Report. IAEA Safeguards: Implementation blueprint of commercial satellite imagery

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Christer [SSC Satellitbild AB, Solna (Sweden)

    2000-01-01

    This document - IAEA Safeguards: Implementation Blueprint of Commercial Satellite Imagery - constitutes the second report from SSC Satellitbild giving a structured view and solid guidelines on how to proceed with a conceivable implementation of satellite imagery to support Safeguards activities of the Agency. This Phase 2 report presents a large number of concrete recommendations regarding suggested management issues, work organisation, imagery purchasing and team building. The study has also resulted in several lists of actions and preliminary project plans with GANT schedules concerning training, hardware and software, as well as for the initial pilot studies. In both the Phase 1 and Phase 2 studies it is confirmed that the proposed concept of a relatively small Imagery Unit using high-resolution data will be a sound and feasible undertaking. Such a unit capable of performing advanced image processing as a tool for various safeguard tasks will give the Agency an effective instrument for reference, monitoring, verification, and detection of declared and undeclared activities. The total cost for implementing commercial satellite imagery at the Department for Safeguards, as simulated in these studies, is approximately MUSD 1,5 per year. This cost is founded on an activity scenario with a staff of 4 experts working in an IAEA Imagery Unit with a workload of three dossiers or issues per week. The imagery unit is built around an advanced PC image processing system capable of handling several hundreds of pre-processed images per year. Alternatively a Reduced Scenario with a staff of 3 would need a budget of approximately MUSD 0,9 per year, whereas an Enhanced Imagery Unit including 5 experts and a considerably enlarged capacity would cost MUSD 1,7 per year. The Imagery Unit should be organised so it clearly reflects the objectives and role as set by the Member States and the management of the Agency. We recommend the Imagery Unit to be organised into four main work

  19. Earth's gravity field modelling based on satellite accelerations derived from onboard GPS phase measurements

    Science.gov (United States)

    Guo, X.; Ditmar, P.; Zhao, Q.; Klees, R.; Farahani, H. H.

    2017-09-01

    GPS data collected by satellite gravity missions can be used for extracting the long-wavelength part of the Earth's gravity field. We propose a new data processing method which makes use of the `average acceleration' approach to gravity field modelling. In this method, satellite accelerations are directly derived from GPS carrier phase measurements with an epoch-differenced scheme. As a result, no ambiguity solutions are needed and the systematic errors that do not change much from epoch to epoch are largely eliminated. The GPS data collected by the Gravity Field and Steady-State Ocean Circulation Explorer (GOCE) satellite mission are used to demonstrate the added value of the proposed method. An analysis of the residual accelerations shows that accelerations derived in this way are more precise, with noise being reduced by about 20 and 5% at the cross-track component and the other two components, respectively, as compared to those based on kinematic orbits. The accelerations obtained in this way allow the recovery of the gravity field to a slightly higher maximum degree compared to the solution based on kinematic orbits. Furthermore, the gravity field solution has an overall better performance. Errors in spherical harmonic coefficients are smaller, especially at low degrees. The cumulative geoid height error is reduced by about 15 and 5% up to degree 50 and 150, respectively. An analysis in the spatial domain shows that large errors along the geomagnetic equator, which are caused by a high electron density coupled with large short-term variations, are substantially reduced. Finally, the new method allows for a better observation of mass transport signals. In particular, sufficiently realistic signatures of regional mass anomalies in North America and south-west Africa are obtained.

  20. Earth's gravity field modelling based on satellite accelerations derived from onboard GPS phase measurements

    Science.gov (United States)

    Guo, X.; Ditmar, P.; Zhao, Q.; Klees, R.; Farahani, H. H.

    2017-02-01

    GPS data collected by satellite gravity missions can be used for extracting the long-wavelength part of the Earth's gravity field. We propose a new data processing method which makes use of the `average acceleration' approach to gravity field modelling. In this method, satellite accelerations are directly derived from GPS carrier phase measurements with an epoch-differenced scheme. As a result, no ambiguity solutions are needed and the systematic errors that do not change much from epoch to epoch are largely eliminated. The GPS data collected by the Gravity Field and Steady-State Ocean Circulation Explorer (GOCE) satellite mission are used to demonstrate the added value of the proposed method. An analysis of the residual accelerations shows that accelerations derived in this way are more precise, with noise being reduced by about 20 and 5% at the cross-track component and the other two components, respectively, as compared to those based on kinematic orbits. The accelerations obtained in this way allow the recovery of the gravity field to a slightly higher maximum degree compared to the solution based on kinematic orbits. Furthermore, the gravity field solution has an overall better performance. Errors in spherical harmonic coefficients are smaller, especially at low degrees. The cumulative geoid height error is reduced by about 15 and 5% up to degree 50 and 150, respectively. An analysis in the spatial domain shows that large errors along the geomagnetic equator, which are caused by a high electron density coupled with large short-term variations, are substantially reduced. Finally, the new method allows for a better observation of mass transport signals. In particular, sufficiently realistic signatures of regional mass anomalies in North America and south-west Africa are obtained.

  1. Notch Antennas

    Science.gov (United States)

    Lee, Richard Q.

    2004-01-01

    Notch antennas, also known as the tapered slot antenna (TSA), have been the topics of research for decades. TSA has demonstrated multi-octave bandwidth, moderate gain (7 to 10 dB), and symmetric E- and H- plane beam patterns and can be used for many different applications. This chapter summarizes the research activities on notch antennas over the past decade with emphasis on their most recent advances and applications. This chapter begins with some discussions on the designs of single TSA; then follows with detailed discussions of issues associated with TSA designs and performance characteristics. To conclude the chapter, some recent developments in TSA arrays and their applications are highlighted.

  2. Phase behavior and thermodynamic modeling of ices - implications for the geophysics of icy satellites. (Invited)

    Science.gov (United States)

    Choukroun, M.

    2010-12-01

    Ground-based observations and space missions to the outer Solar System (Voyager, Galileo, Cassini-Huygens) have evidenced recent geologic activity on many satellites of the giant planets. The diversity in surface expression of these icy moons’ activity is striking: from a scarred and young surface on Europa,1 with hydrated salts that may originate from a liquid layer buried at depth,2 to the South Polar plumes of Enceladus,3 where water ice particles are expelled along with a myriad of more complex molecules,4 to Titan, largest satellite of Saturn, with a dense atmosphere and a hydrocarbon cycle similar to the hydrological cycle on Earth.5 Large icy moons, i.e. with a radius greater than 500 km, share two particularities: a high content in water (on the order of a 30-70% bulk composition), and an interior segregated between a water-dominated mantle and a silicate-dominated core. The many forms water may have beneath the surface (ice polymorphs, liquid, hydrated compounds) bear a crucial role in the detected or alleged activity, and in the potential for astrobiological relevance. Indeed, any endogenic activity can only be approached through geophysical modelling of the internal structure and the thermal evolution. Current internal structure models for the icy moonse.g.,6 rely mainly on the contribution of each internal layer to the moment of inertia, generating non-unique solutions due to the large variability in density of H2O-bearing phases. Thermal evolution models,e.g.,7 can help constrain further the internal structure and geophysical activity, by starting with a given initial composition and state and investigating the thickening of icy layers through time. However, such models require both observational datasets and a precise description, as a function of pressure, temperature, and composition, of the thermophysical properties of the individual layers. Over the past century, experimental studies have provided a comprehensive view of the phase diagram of

  3. Carrier-phase Two-Way Satellite Frequency Transfer over a Very Long Baseline

    CERN Document Server

    Fujieda, M; Gotoh, T; Becker, J; Aida, M; Bauch, A

    2014-01-01

    In this paper we report that carrier-phase two-way satellite time and frequency transfer (TWSTFT) was successfully demonstrated over a very long baseline of 9,000 km, established between the National Institute of Information and Communications Technology (NICT) and the Physikalisch-Technische Bundesanstalt (PTB). We verified that the carrier-phase TWSTFT (TWCP) result agreed with those obtained by conventional TWSTFT and GPS carrier-phase (GPSCP) techniques. Moreover, a much improved short-term instability for frequency transfer of $2\\times10^{-13}$ at 1 s was achieved, which is at the same level as previously confirmed over a shorter baseline within Japan. The precision achieved was so high that the effects of ionospheric delay became significant which are ignored in conventional TWSTFT even over a long link. We compensated for these effects using ionospheric delays computed from regional vertical total electron content maps. The agreement between the TWCP and GPSCP results was improved because of this compe...

  4. The CARMA Paired Antenna Calibration System: Atmospheric Phase Correction for Millimeter Wave Interferometry and Its Application to Mapping the Ultraluminous Galaxy Arp 193

    Science.gov (United States)

    Zauderer, B. Ashley; Bolatto, Alberto D.; Vogel, Stuart N.; Carpenter, John M.; Peréz, Laura M.; Lamb, James W.; Woody, David P.; Bock, Douglas C.-J.; Carlstrom, John E.; Culverhouse, Thomas L.; Curley, Roger; Leitch, Erik M.; Plambeck, Richard L.; Pound, Marc W.; Marrone, Daniel P.; Muchovej, Stephen J.; Mundy, Lee G.; Teng, Stacy H.; Teuben, Peter J.; Volgenau, Nikolaus H.; Wright, Melvyn C. H.; Wu, Dalton

    2016-01-01

    Phase fluctuations introduced by the atmosphere are the main limiting factor in attaining diffraction limited performance in extended interferometric arrays at millimeter and submillimeter wavelengths. We report the results of C-PACS, the Combined Array for Research in Millimeter-Wave Astronomy Paired Antenna Calibration System. We present a systematic study of several hundred test observations taken during the 2009-2010 winter observing season where we utilize CARMA's eight 3.5 m antennas to monitor an atmospheric calibrator while simultaneously acquiring science observations with 6.1 and 10.4 m antennas on baselines ranging from a few hundred meters to ˜2 km. We find that C-PACS is systematically successful at improving coherence on long baselines under a variety of atmospheric conditions. We find that the angular separation between the atmospheric calibrator and target source is the most important consideration, with consistently successful phase correction at CARMA requiring a suitable calibrator located ≲6° away from the science target. We show that cloud cover does not affect the success of C-PACS. We demonstrate C-PACS in typical use by applying it to the observations of the nearby very luminous infrared galaxy Arp 193 in 12CO(2-1) at a linear resolution of ≈70 pc (0.″12 × 0.″18), 3 times better than previously published molecular maps of this galaxy. We resolve the molecular disk rotation kinematics and the molecular gas distribution and measure the gas surface densities and masses on 90 pc scales. We find that molecular gas constitutes ˜30% of the dynamical mass in the inner 700 pc of this object with a surface density ˜104 M⊙ pc-2 we compare these properties to those of the starburst region of NGC 253.

  5. THE CARMA PAIRED ANTENNA CALIBRATION SYSTEM: ATMOSPHERIC PHASE CORRECTION FOR MILLIMETER WAVE INTERFEROMETRY AND ITS APPLICATION TO MAPPING THE ULTRALUMINOUS GALAXY ARP 193

    Energy Technology Data Exchange (ETDEWEB)

    Zauderer, B. Ashley; Bolatto, Alberto D.; Vogel, Stuart N.; Curley, Roger; Pound, Marc W.; Mundy, Lee G.; Teng, Stacy H.; Teuben, Peter J. [Department of Astronomy, University of Maryland, College Park, MD 20742 (United States); Carpenter, John M. [California Institute of Technology, Department of Astronomy, MC 249-17, Pasadena, CA 91125 (United States); Peréz, Laura M. [National Radio Astronomy Observatory, P.O. Box 0, Socorro, NM 87801 (United States); Lamb, James W.; Woody, David P.; Leitch, Erik M.; Muchovej, Stephen J.; Volgenau, Nikolaus H. [California Institute of Technology, Owens Valley Radio Observatory, Big Pine, CA 93513 (United States); Bock, Douglas C.-J. [CSIRO Astronomy and Space Science, P.O. Box 76, Epping NSW 1710 (Australia); Carlstrom, John E.; Culverhouse, Thomas L. [Department of Astronomy and Astrophysics, University of Chicago, 5640 S. Ellis Ave., Chicago, IL 60637 (United States); Plambeck, Richard L. [Radio Astronomy Laboratory, University of California, Berkeley, 601 Campbell Hall, Berkeley, CA 94720 (United States); Marrone, Daniel P. [Department of Astronomy, Steward Observatory, University of Arizona, Tucson, AZ 85721 (United States); and others

    2016-01-15

    Phase fluctuations introduced by the atmosphere are the main limiting factor in attaining diffraction limited performance in extended interferometric arrays at millimeter and submillimeter wavelengths. We report the results of C-PACS, the Combined Array for Research in Millimeter-Wave Astronomy Paired Antenna Calibration System. We present a systematic study of several hundred test observations taken during the 2009–2010 winter observing season where we utilize CARMA's eight 3.5 m antennas to monitor an atmospheric calibrator while simultaneously acquiring science observations with 6.1 and 10.4 m antennas on baselines ranging from a few hundred meters to ∼2 km. We find that C-PACS is systematically successful at improving coherence on long baselines under a variety of atmospheric conditions. We find that the angular separation between the atmospheric calibrator and target source is the most important consideration, with consistently successful phase correction at CARMA requiring a suitable calibrator located ≲6° away from the science target. We show that cloud cover does not affect the success of C-PACS. We demonstrate C-PACS in typical use by applying it to the observations of the nearby very luminous infrared galaxy Arp 193 in {sup 12}CO(2-1) at a linear resolution of ≈70 pc (0.″12 × 0.″18), 3 times better than previously published molecular maps of this galaxy. We resolve the molecular disk rotation kinematics and the molecular gas distribution and measure the gas surface densities and masses on 90 pc scales. We find that molecular gas constitutes ∼30% of the dynamical mass in the inner 700 pc of this object with a surface density ∼10{sup 4} M{sub ⊙} pc{sup −2}; we compare these properties to those of the starburst region of NGC 253.

  6. Improved Low-Profile Helical Antenna Design for INMARSAT Applications

    Directory of Open Access Journals (Sweden)

    Shiqiang Fu

    2012-01-01

    Full Text Available A new low-profile variable pitch angle cylindrical helical antenna employing a copper strip as impedance transformer is proposed in this paper. Under the circumstance of a limited antenna height, the circular polarization performance of the antenna has been enhanced by changing the pitch angle and the input impedance matching has been improved by adjusting the copper strip match stub. The design method of the proposed antenna is given. The optimal antenna structure for INMARSAT application has been fabricated and measured. The measured results show that in the whole maritime satellite communication work band the VSWR is less than 1.2, its antenna gain is higher than 9 dBi, and the axial ratio is lower than 2.5 dB. The experimental results have a good agreement with the simulations. The proposed antenna is compact and easy tuning. It provides a promising antenna element for maritime satellite communication applications.

  7. 低轨卫星系统星载多波束天线点波束设计及优化%Spot -beam Design and Optimization of On- board Multi -beam Antenna for LEO Satellite Systems

    Institute of Scientific and Technical Information of China (English)

    张旭; 吴潜

    2009-01-01

    星载多波束天线具有广阔的应用前景,尤其适合应用于低轨卫星系统.讨论了星载多波束天线点波束设计的方法,为平衡点波束各覆盖区域的接收增益,借鉴最优化理论思想,提出了一种点波束设计的方法,以全球星系统为例进行分析,结果表明该方法较典型的点波束设计方法具有更高的满意度.%Muhi - beam antenna is widely used in low earth orbit(LEO) satellite systems. Spot - beam de-sign of on - board multi - beam antenna is discussed, an optimized method adopting optimization theory for spot -beam design is proposed to balance the receiving gain of each spot -beam covering area, analysis of the optimized method for Globalstar system is given, and higher satisfaction of the proposed method is proved.

  8. Design and rigorous analysis of generalized axially- symmetric dual-reflector antennas

    Science.gov (United States)

    Moreira, Fernando J. S.

    1997-10-01

    The development of reflector antennas is continuously driven by ever increasing performance requirements, creating a demand for improved design and analysis tools. Ideally, the antenna synthesis should rely on general closed-form design equations (to establish the initial geometry and performance), as well as on accurate analysis techniques (to tune up the antenna performance by accounting for all pertinent electrical effects). Driven by these motivations, this dissertation provides the required formulation for the rigorous (in a numerical sense) analysis of axially-symmetric dual-reflector antennas and for their effective design. The rigorous analysis is performed using integral-equation techniques, which permit the inclusion of all relevant antenna components (i.e., reflector surfaces and feed structure), with the exception of the supporting struts and radomes. These techniques allow the electrical performance of a designed antenna to be accurately determined, hence minimizing the use of hardware models. The design portion starts with a unified investigation of generalized classical axially-symmetric dual-reflector antennas- conic-section generated configurations that minimize the main-reflector scattering towards the subreflector while providing a uniform-phase aperture illumination. It is shown that all possible configurations can be grouped in four basic categories. Using Geometrical Optics principles, useful closed-form design expressions are obtained, allowing a straightforward determination of the initial geometry and its upper-bound high-frequency performance. The improvement of the antenna radiation characteristics through the reflector shaping is also explored. An amplitude distribution is proposed for the shaped-antenna aperture field (with constant phase), providing high efficiency while controlling the sidelobe envelope. The diffraction and spillover effects are also investigated using Geometrical Theory of Diffraction, yielding useful formulas and

  9. Phase 2 Final Report. IAEA Safeguards: Implementation blueprint of commercial satellite imagery

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Christer [SSC Satellitbild AB, Solna (Sweden)

    2000-01-01

    This document - IAEA Safeguards: Implementation Blueprint of Commercial Satellite Imagery - constitutes the second report from SSC Satellitbild giving a structured view and solid guidelines on how to proceed with a conceivable implementation of satellite imagery to support Safeguards activities of the Agency. This Phase 2 report presents a large number of concrete recommendations regarding suggested management issues, work organisation, imagery purchasing and team building. The study has also resulted in several lists of actions and preliminary project plans with GANT schedules concerning training, hardware and software, as well as for the initial pilot studies. In both the Phase 1 and Phase 2 studies it is confirmed that the proposed concept of a relatively small Imagery Unit using high-resolution data will be a sound and feasible undertaking. Such a unit capable of performing advanced image processing as a tool for various safeguard tasks will give the Agency an effective instrument for reference, monitoring, verification, and detection of declared and undeclared activities. The total cost for implementing commercial satellite imagery at the Department for Safeguards, as simulated in these studies, is approximately MUSD 1,5 per year. This cost is founded on an activity scenario with a staff of 4 experts working in an IAEA Imagery Unit with a workload of three dossiers or issues per week. The imagery unit is built around an advanced PC image processing system capable of handling several hundreds of pre-processed images per year. Alternatively a Reduced Scenario with a staff of 3 would need a budget of approximately MUSD 0,9 per year, whereas an Enhanced Imagery Unit including 5 experts and a considerably enlarged capacity would cost MUSD 1,7 per year. The Imagery Unit should be organised so it clearly reflects the objectives and role as set by the Member States and the management of the Agency. We recommend the Imagery Unit to be organised into four main work

  10. BeiDou and Galileo, Two Global Satellite Navigation Systems in Final Phase of the Construction, Visibility and Geometry

    Directory of Open Access Journals (Sweden)

    Jacek Januszewski

    2016-09-01

    Full Text Available Spatial segment is one of three segments of each satellite navigation systems (SNS. Nowadays two SNSs, GPS and GLONASS, are fully operational, two next SNSs, BeiDou in China and Galileo in Europe, are in final phase of the construction. In the case of China system this segment will consist of 35 satellites with three types of orbits ? medium (MEO, geostationary (GEO and inclined geosynchronous (IGSO. As GEO and IGSO satellites can be used in China and Asia-Pacific region only, BeiDou MEO constellation with 27 fully operational satellites will be taken into account in this paper. The orbital planes of the Galileo constellation will be divided in “slots” that contains at least one operational satellite. The Galileo reference constellation has 24 nominal orbital positions or operational slots in MEO homogeneously distributed in 3 orbital planes; i.e. 8 slots equally spaced per plane. As the error of user’s position obtained from both systems depends on geometry factor DOP (Dilution Of Precision among other things the knowledge of the number of satellites visible by the user above given masking elevation angle Hmin and the distributions of DOP coefficient values, GDOP in particular, is very important. The lowest and the greatest number of satellites visible in open area by the observer at different latitudes for different Hmin, the percentage of satellites visible above angle H, distributions (in per cent of satellites azimuths and GDOP coefficient values for different Hmin for BeiDou and Galileo systems at different latitudes are presented in the paper.

  11. Free space millimeter wave-coupled electro-optic high speed nonlinear polymer phase modulator with in-plane slotted patch antennas.

    Science.gov (United States)

    Park, D H; Pagán, V R; Murphy, T E; Luo, J; Jen, A K-Y; Herman, W N

    2015-04-06

    We report in-plane slotted patch antenna-coupled electro-optic phase modulators with a carrier-to-sideband ratio (CSR) of 22 dB under an RF power density of 120 W/m(2) and a figure of merit of 2.0 W(-1/2) at the millimeter wave frequencies of 36-37 GHz based on guest-host type of second-order nonlinear polymer SEO125. CSR was improved more than 20 dB by using a SiO(2) protection layer. We demonstrate detection of 3 GHz modulation of the RF carrier. We also derive closed-form expressions for the modulated phase of optical wave and carrier-to-sideband ratio. Design, simulation, fabrication, and experimental results are discussed.

  12. PHASES: a concept for a satellite-borne ultra-precise spectrophotometer

    CERN Document Server

    del Burgo, Carlos; Peacocke, Tully; 10.1088/1748-0221/5/01/P01006

    2010-01-01

    The Planet Hunting and Asteroseismology Explorer Spectrophotometer, PHASES, is a concept for a space-borne instrument to obtain flux calibrated spectra and measure micro-magnitude photometric variations of nearby stars. The science drivers are the determination of the physical properties of stars and the characterisation of planets orbiting them, to very high precision. PHASES, intended to be housed in a micro-satellite, consists of a 20 cm aperture modified Baker telescope feeding two detectors: the tracking detector, with a field of 1 degree square, and the science detector for performing spectrophotometry. The optical design has been developed with the primary goal of avoiding stray light on the science detector, while providing spectra in the wavelength range 370-960 nm with a resolving power that ranges from ~900 at 370 nm to ~200 at 960 nm. The signal to noise per resolution element obtained for a V=10 magnitude star in a 1 minute integration varies between ~ 35 and 140. An analysis of the light curve c...

  13. Q-Band (37-41 GHz) Satellite Beacon Architecture for RF Propagation Experiments

    Science.gov (United States)

    Simmons, Rainee N.; Wintucky, Edwin G.

    2012-01-01

    In this paper, the design of a beacon transmitter that will be flown as a hosted payload on a geostationary satellite to enable propagation experiments at Q-band (37-41 GHz) frequencies is presented. The beacon uses a phased locked loop stabilized dielectric resonator oscillator and a solid-state power amplifier to achieve the desired output power. The satellite beacon antenna is configured as an offset-fed cut-paraboloidal reflector.

  14. Q-Band (37 to 41 GHz) Satellite Beacon Architecture for RF Propagation Experiments

    Science.gov (United States)

    Simons, Rainee N.; Wintucky, Edwin G.

    2014-01-01

    In this paper, the design of a beacon transmitter that will be flown as a hosted payload on a geostationary satellite to enable propagation experiments at Q-band (37 to 41 GHz) frequencies is presented. The beacon uses a phased locked loop stabilized dielectric resonator oscillator and a solid-state power amplifier to achieve the desired output power. The satellite beacon antenna is configured as an offset-fed cutparaboloidal reflector.

  15. Precise Calibration of a GNSS Antenna Array for Adaptive Beamforming Applications

    Directory of Open Access Journals (Sweden)

    Saeed Daneshmand

    2014-05-01

    Full Text Available The use of global navigation satellite system (GNSS antenna arrays for applications such as interference counter-measure, attitude determination and signal-to-noise ratio (SNR enhancement is attracting significant attention. However, precise antenna array calibration remains a major challenge. This paper proposes a new method for calibrating a GNSS antenna array using live signals and an inertial measurement unit (IMU. Moreover, a second method that employs the calibration results for the estimation of steering vectors is also proposed. These two methods are applied to the receiver in two modes, namely calibration and operation. In the calibration mode, a two-stage optimization for precise calibration is used; in the first stage, constant uncertainties are estimated while in the second stage, the dependency of each antenna element gain and phase patterns to the received signal direction of arrival (DOA is considered for refined calibration. In the operation mode, a low-complexity iterative and fast-converging method is applied to estimate the satellite signal steering vectors using the calibration results. This makes the technique suitable for real-time applications employing a precisely calibrated antenna array. The proposed calibration method is applied to GPS signals to verify its applicability and assess its performance. Furthermore, the data set is used to evaluate the proposed iterative method in the receiver operation mode for two different applications, namely attitude determination and SNR enhancement.

  16. Precise calibration of a GNSS antenna array for adaptive beamforming applications.

    Science.gov (United States)

    Daneshmand, Saeed; Sokhandan, Negin; Zaeri-Amirani, Mohammad; Lachapelle, Gérard

    2014-05-30

    The use of global navigation satellite system (GNSS) antenna arrays for applications such as interference counter-measure, attitude determination and signal-to-noise ratio (SNR) enhancement is attracting significant attention. However, precise antenna array calibration remains a major challenge. This paper proposes a new method for calibrating a GNSS antenna array using live signals and an inertial measurement unit (IMU). Moreover, a second method that employs the calibration results for the estimation of steering vectors is also proposed. These two methods are applied to the receiver in two modes, namely calibration and operation. In the calibration mode, a two-stage optimization for precise calibration is used; in the first stage, constant uncertainties are estimated while in the second stage, the dependency of each antenna element gain and phase patterns to the received signal direction of arrival (DOA) is considered for refined calibration. In the operation mode, a low-complexity iterative and fast-converging method is applied to estimate the satellite signal steering vectors using the calibration results. This makes the technique suitable for real-time applications employing a precisely calibrated antenna array. The proposed calibration method is applied to GPS signals to verify its applicability and assess its performance. Furthermore, the data set is used to evaluate the proposed iterative method in the receiver operation mode for two different applications, namely attitude determination and SNR enhancement.

  17. Autonomous Satellite Command and Control Through the World Wide Web. Phase 3

    Science.gov (United States)

    Cantwell, Brian; Twiggs, Robert

    1998-01-01

    The Automated Space System Experimental Testbed (ASSET) system is a simple yet comprehensive real-world operations network being developed. Phase 3 of the ASSET Project was January-December 1997 and is the subject of this report. This phase permitted SSDL and its project partners to expand the ASSET system in a variety of ways. These added capabilities included the advancement of ground station capabilities, the adaptation of spacecraft on-board software, and the expansion of capabilities of the ASSET management algorithms. Specific goals of Phase 3 were: (1) Extend Web-based goal-level commanding for both the payload PI and the spacecraft engineer. (2) Support prioritized handling of multiple (PIs) Principle Investigators as well as associated payload experimenters. (3) Expand the number and types of experiments supported by the ASSET system and its associated spacecraft. (4) Implement more advanced resource management, modeling and fault management capabilities that integrate the space and ground segments of the space system hardware. (5) Implement a beacon monitoring test. (6) Implement an experimental blackboard controller for space system management. (7) Further define typical ground station developments required for Internet-based remote control and for full system automation of the PI-to-spacecraft link. Each of those goals are examined. Significant sections of this report were also published as a conference paper. Several publications produced in support of this grant are included as attachments. Titles include: 1) Experimental Initiatives in Space System Operations; 2) The ASSET Client Interface: Balancing High Level Specification with Low Level Control; 3) Specifying Spacecraft Operations At The Product/Service Level; 4) The Design of a Highly Configurable, Reusable Operating System for Testbed Satellites; 5) Automated Health Operations For The Sapphire Spacecraft; 6) Engineering Data Summaries for Space Missions; and 7) Experiments In Automated Health

  18. Circularly polarized antennas

    CERN Document Server

    Gao, Steven; Zhu, Fuguo

    2013-01-01

    This book presents a comprehensive insight into the design techniques for different types of CP antenna elements and arrays In this book, the authors address a broad range of topics on circularly polarized (CP) antennas. Firstly, it introduces to the reader basic principles, design techniques and characteristics of various types of CP antennas, such as CP patch antennas, CP helix antennas, quadrifilar helix antennas (QHA), printed quadrifilar helix antennas (PQHA), spiral antenna, CP slot antennas, CP dielectric resonator antennas, loop antennas, crossed dipoles, monopoles and CP horns. Adva

  19. Nanorod optical antennas for dipolar transitions

    CERN Document Server

    Taminiau, Tim H; van Hulst, Niek F

    2009-01-01

    Optical antennas link objects to light. Here, we analyze metal nanorod antennas as cavities with variable reflection coefficients to derive the interaction of dipolar transitions with radiation through the antenna modes. The presented analytical model accurately describes the complete emission process, and is summarized in a phase-matching equation. We show how antenna modes evolve as they become increasingly more bound, i.e. plasmonic. The results illustrate why efficient antennas should not be too plasmonic, and how subradiant even modes can evolve into weakly-interacting dark modes. Our description is valid for the interaction of nanorods with light in general, and is thus widely applicable.

  20. Diamond dipole active antenna

    OpenAIRE

    Bubnov, Igor N.; Falkovych, I. S.; Gridin, A. A.; Stanislavsky, A. A.; Reznik, A. P.

    2015-01-01

    Advantages of the diamond dipole antenna as an active antenna are presented. Such an antenna is like an inverted bow-tie antenna, but the former has some advantages over the ordinary bow-tie antenna. It is shown that the diamond dipole antenna may be an effective element of a new antenna array for low-frequency radio astronomy as well as a communication antenna.

  1. Modeling C-Band Co-Channel Interference From AeroMACS Omni-Directional Antennas to Mobile Satellite Service Feeder Uplinks

    Science.gov (United States)

    Wilson, Jeffrey D.

    2011-01-01

    A new C-band (5091 to 5150 MHz) airport communications system designated as Aeronautical Mobile Airport Communications System (AeroMACS) is being planned under the Federal Aviation Administration s NextGen program. An interference analysis software program, Visualyse Professional (Transfinite Systems Ltd), is being utilized to provide guidelines on limitations for AeroMACS transmitters to avoid interference with other systems. A scenario consisting of a single omni-directional transmitting antenna at each of the major contiguous United States airports is modeled and the steps required to build the model are reported. The results are shown to agree very well with a previous study.

  2. 相控阵天线阵面测试平台软件设计%Software Design of Phased Array Antenna Array Testing Platform

    Institute of Scientific and Technical Information of China (English)

    万东成; 章国宝

    2016-01-01

    In modern large phased array radar,the number of transmitter and receiver components in the antenna is large. The system test is very cumbersome.In order to simplify the testing process and improve the efficiency of manual test,in the array front and TR components testing process,combining with computer software & hardware technologies,data processing technology,automatic test technology,by means of network communication,a set of antenna array surface general test plat-form is designed in this paper.%现代大型相控阵雷达中,天线内的发射和接收(TR)组件数目庞大,系统测试工作十分繁琐,为简化测试过程,提高测试效率,在阵面以及TR组件测试过程中,综合运用计算机软硬件技术、数据处理技术、自动测试技术,采用网络通信手段,设计了一套天线阵面通用测试平台。

  3. Design of Automatic Testing System for Active Phased Array Antenna%有源相控阵天线自动测试系统设计

    Institute of Scientific and Technical Information of China (English)

    熊毅; 符伟; 钱林; 何诚; 陶成忠

    2012-01-01

    Aimed at multi-channel, large amount of testing data, low test efficiency in T/R module test of active phased array antenna, we designed an automatic test system for active phased array antenna, which adapts to testing large amount of T/R modules. The system controls VNA and gathers data from it via GPIB or ethernet and fully uses strong ability of modern computer for processing and analyzing data. It not only solves the problems of trouble diagnosis and automatic calibration of active phased array, but also improves the work efficiency and saves human cost. Results of actual application show that the test system works stably, and is easy to operate, it can meet the demands for measuring T/R module.%针对现代有源相控阵雷达天线T/R组件测试通路多、测试数据处理量大、测试效率低的特点,设计了一种适用于大规模T/R组件测试的有源相控阵天线自动测试系统.该系统设计通过GPIB接口或以太网对VNA(矢量网络分析仪)进行访问控制与数据采集,充分利用了现代计算机强大的数据处理与分析能力,不仅解决了有源相控阵天线故障诊断与自动校正问题,而且还极大地提高了工作效率,节约了人力成本.实际应用表明:该测试系统工作稳定,使用方便,能够充分满足T/R组件测试需要.

  4. Fresnel zone and reflectarray antennas for space missions: Concepts, computational techniques and characterizations

    Science.gov (United States)

    Khayatian, Behrouz

    Reflector antennas generally employ parabolic shaped main reflectors and have found a wide range of applications for both earth stations and satellite systems. Increasingly, one may find many advantages in minimizing antenna shaping requirement and weight as well as more compact designs by employing flat reflectors (either on the main reflector or on the subreflector) which can achieve a desired set of criteria for antenna performance. Two electrically large antennas which use flat min reflectors are Fresnel Zone (FZ) and reflectarray antennas which are being addressed in this dissertation. Analytical techniques are proposed, implemented, and verified to analyze these reflector geometries. A two dimensional (2-D) multi-scatterer analysis is formulated and implemented using various electromagnetic scattering techniques such as Physical Optics (PO), Method of Moments (MoM), and Geometrical Theory of Diffraction (GTD). The capability of the 2-D technique is further extended for dual reflector analysis with flat subreflector panels as well as design and analysis of FZ antennas with a proposed space missions application in solar sailing. FZ antenna design is based on establishing regions of quasi-uniform phases according to the PO current on the reflector face. The concepts extracted from the 2-D analysis of FZ reflectors is carried to the three dimensional (3-D) cases and incorporated into a multi reflector code, which has been widely used in variety of reflector applications. Like FZ antennas, reflectarrays work according to a similar set of principals by achieving a uniform phase current on the flat reflectarray surface. Accordingly, an analytical methodology is proposed and implemented within the structure of the multi-reflector code to analyze and give design criteria for both single and dual reflectarray configurations. This technique is compared to measured results published for single reflectarrays and is investigated for near-field Gregorian reflectarrays with

  5. Detection of supercooled liquid water-topped mixed-phase clouds >from shortwave-infrared satellite observations

    Science.gov (United States)

    NOH, Y. J.; Miller, S. D.; Heidinger, A. K.

    2015-12-01

    Many studies have demonstrated the utility of multispectral information from satellite passive radiometers for detecting and retrieving the properties of cloud globally, which conventionally utilizes shortwave- and thermal-infrared bands. However, the satellite-derived cloud information comes mainly from cloud top or represents a vertically integrated property. This can produce a large bias in determining cloud phase characteristics, in particular for mixed-phase clouds which are often observed to have supercooled liquid water at cloud top but a predominantly ice phase residing below. The current satellite retrieval algorithms may report these clouds simply as supercooled liquid without any further information regarding the presence of a sub-cloud-top ice phase. More accurate characterization of these clouds is very important for climate models and aviation applications. In this study, we present a physical basis and preliminary results for the algorithm development of supercooled liquid-topped mixed-phase cloud detection using satellite radiometer observations. The detection algorithm is based on differential absorption properties between liquid and ice particles in the shortwave-infrared bands. Solar reflectance data in narrow bands at 1.6 μm and 2.25 μm are used to optically probe below clouds for distinction between supercooled liquid-topped clouds with and without an underlying mixed phase component. Varying solar/sensor geometry and cloud optical properties are also considered. The spectral band combination utilized for the algorithm is currently available on Suomi NPP Visible/Infrared Imaging Radiometer Suite (VIIRS), Himawari-8 Advanced Himawari Imager (AHI), and the future GOES-R Advance Baseline Imager (ABI). When tested on simulated cloud fields from WRF model and synthetic ABI data, favorable results were shown with reasonable threat scores (0.6-0.8) and false alarm rates (0.1-0.2). An ARM/NSA case study applied to VIIRS data also indicated promising

  6. Feedforward attitude control for a TDRS with mobile antennas

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    In this paper, feedforward attitude control law for a Tracking and Data Relay Satellite (TDRS) with mobile antennas is proposed. To track or point the target spacecraft with median/law orbit, the large mobile antennas have to move in a wide range. The movement of such mobile antennas disturbs the satellite attitude consequently. Conventionally, the main body of the satellite and the mobile antennas are controlled independently.The proposed controller first estimates the angular momentum which the mobile antennas will produce based on the momentum conservation equation. Next, it computes the desired velocity of reaction wheels to compensate the disturbance due to the antenna motion. It then adds the error of the wheels' velocity between a desired one and a current value as a feedforward signal to the control system. The proposed controller is demonstrated using a mathematical simulation, of which these results coincide well with analytical results.

  7. Integrated Antenna/Solar Array Cell (IA/SAC) System for Flexible Access Communications

    Science.gov (United States)

    Lee, Ricard Q.; Clark, Eric B.; Pal, Anna Maria T.; Wilt, David M.; Mueller, Carl H.

    2004-01-01

    Present satellite communications systems normally use separate solar cells and antennas. Since solar cells generally account for the largest surface area of the spacecraft, co-locating the antenna and solar cells on the same substrate opens the possibility for a number of data-rate-enhancing communications link architecture that would have minimal impact on spacecraft weight and size. The idea of integrating printed planar antenna and solar array cells on the same surface has been reported in the literature. The early work merely attempted to demonstrate the feasibility by placing commercial solar cells besides a patch antenna. Recently, Integrating multiple antenna elements and solar cell arrays on the same surface was reported for both space and terrestrial applications. The application of photovoltaic solar cell in a planar antenna structure where the radiating patch antenna is replaced by a Si solar cell has been demonstrated in wireless communication systems (C. Bendel, J. Kirchhof and N. Henze, 3rd Would Photovotaic Congress, Osaka, Japan, May 2003). Based on a hybrid approach, a 6x1 slot array with circularly polarized crossdipole elements co-located on the same surface of the solar cells array has been demonstrated (S. Vaccaro, J. R. Mosig and P. de Maagt, IEEE Trans. Ant. and Propag., Vol. 5 1, No. 8, Aug. 2003). Amorphous silicon solar cells with about 5-10% efficiency were used in these demonstrations. This paper describes recent effort to integrate advanced solar cells with printed planar antennas. Compared to prior art, the proposed WSAC concept is unique in the following ways: 1) Active antenna element will be used to achieve dynamic beam steering; 2) High efficiency (30%) GaAs multi-junction solar cells will be used instead of Si, which has an efficiency of about 15%; 3) Antenna and solar cells are integrated on a common GaAs substrate; and 4) Higher data rate capability. The IA/SAC is designed to operate at X-band (8-12 GH) and higher frequencies

  8. Highly Enhanced Risk Management Emergency Satellite

    DEFF Research Database (Denmark)

    Dalmeir, Michael; Gataullin, Yunir; Indrajit, Agung

    HERMES (Highly Enhanced Risk Management Emergency Satellite) is potential European satellite mission for global flood management, being implemented by Technical University Munich and European Space Agency. With its main instrument - a reliable and precise Synthetic Aperture Radar (SAR) antenna...

  9. An optimal antenna motion generation using shortest path planning

    Science.gov (United States)

    Jeon, Moon-Jin; Kwon, Dong-Soo

    2017-03-01

    This paper considers an angular velocity minimization method for a satellite antenna. For high speed transmission of science data, a directional antenna with a two-axis gimbal is generally used. When a satellite passes over a ground station while pointing directly at it, the angular velocity of the satellite antenna can increase rapidly due to the gimbal kinematics. The high angular velocity could exceed the dynamic constraint of the antenna. Furthermore, micro vibration induced by high speed antenna rotation during an imaging operation might cause jitter, which can degrade the satellite image quality. To solve this problem, a minimum-velocity antenna motion generation method is proposed. Boundaries of the azimuth and elevation angles of the antenna within an effective beam width are derived using antenna geometry. A minimum-velocity azimuth profile and elevation profile within the boundaries are generated sequentially using a shortest path planning method. For fast and correct generation of the shortest path, a new algorithm called a string nailing algorithm is proposed. A numerical simulation shows that the antenna profile generated by the shortest path planning has a much lower angular velocity than the profiles generated by previous methods. The proposed string nailing algorithm also spends much less computation time than a search-based shortest path planning algorithm to generate almost the same antenna profiles.

  10. Planar antenna system for direction finding

    Science.gov (United States)

    Mardale, Iulia-Cezara; Cocias, Gabriela; Dumitrascu, Ana; Tamas, Razvan; Berescu, Serban

    2015-02-01

    Applications of direction finding techniques include detection and localization of pulsed electromagnetic sources. This paper presents the design and analysis of a planar antenna system for direction finding. Our proposed system includes 4 hybrid couplers that generate 900 shifted signals, 2 crossover couplers also known as 0dB couplers, two 450 phase shifters, two 00 phase shifters and 4 patch antennas.

  11. PHASES: a concept for a satellite-borne ultra-precise spectrophotometer

    Energy Technology Data Exchange (ETDEWEB)

    Burgo, C del [UNINOVA-CA3, Campus da Caparica, Quinta da Torre, Monte de Caparica 2825-149, Caparica (Portugal); Prieto, C Allende [Mullard Space Science Laboratory, University College London, Holmbury St. Mary, Dorking, Surrey RH5 6NT (United Kingdom); Peacocke, T, E-mail: cburgo@uninova.p [Experimental Physics, National University of Ireland, Maynooth, Co. Kildare (Ireland)

    2010-01-15

    The Planet Hunting and Asteroseismology Explorer Spectrophotometer, PHASES, is a concept for a space-borne instrument to obtain flux calibrated spectra and measure micro-magnitude photometric variations of nearby stars. The science drivers are the determination of the physical properties of stars and the characterisation of planets orbiting them, to very high precision. PHASES, intended to be housed in a micro-satellite, consists of a 20 cm aperture modified Baker telescope feeding two detectors: the tracking detector, with a field of 1 degree square, and the science detector for performing spectrophotometry. The optical design has been developed with the primary goal of avoiding stray light on the science detector, while providing spectra in the wavelength range 370-960 nm with a resolving power that ranges from {approx} 900 at 370 nm to {approx} 200 at 960 nm. The signal to noise per resolution element obtained for a V = 10 magnitude star in a 1 minute integration varies between {approx} 35 and 140. An analysis of the light curve constrains the radii of the planets relative to their parent stars' radii, which are, in turn, tightly constrained by the combination of absolute spectrophotometry and trigonometric parallaxes. The provisional optical design satisfies all the scientific requirements, including a {approx} 1% rms flux calibration strategy based on observations of bright A-type stars and model atmospheres, allowing the determination of stellar angular diameters for nearby solar-like stars to 0.5%. This level of accuracy will be propagated to the stellar radii for the nearest stars, with highly reliable Hipparcos parallaxes, and more significantly, to the planetary radii.

  12. Icy satellites of Saturn: disk-integrated observations of the brightness opposition surge at low phase angles

    Science.gov (United States)

    Kulyk, I.; Jockers, K.

    2007-08-01

    The surfaces of most atmosphereless bodies exhibit two interesting optical phenomena at small phase angles, namely a strong brightness increase and negative values of the degree of linear polarization. Of particular interest is the appearance a nonlinear growth of the surface brightness and a second narrow minimum of polarization at phase angles less than 1-3°. These features of brightness and polarization in the narrow phase angle range near opposition are called the photometric and polarimetric opposition effects. These phenomena have attracted increased attention from the perspective of theories of light scattering in random media and their application to the determination of properties of the upper optically active regolith layers on the atmosphereless bodies. However, up to now photometric and especially polarimetric observations conducted at small phase angles are rare. In order to enlarge the amount of available observational data we have conducted photopolarimetric observations of the major icy Saturnian satellites. The observations were performed at the 2m-telescope of the Bulgarian National Observatory with the Two-Channel Focal Reducer of the Bulgarian Academy of Sciences built at the Max-Planck-Institute for Solar System Science. This instrument incorporates a two-channel imaging polarimeter which can be used in coronagraph setup. The light of Saturn and its rings is almost fully absorbed by a black glass and its diffraction pattern is eliminated by a Lyot stop. The photopolarimeter records intensity and degree of polarization of the satellites in two colors simultaneously. In this study, we present the first results of the disk-integrated photometry of Enceladus, Tethys, Dione, and Rhea in the red (center wavelength 694 nm, FWHM 79 nm) and near-infrared (center wavelength 888.5 nm, FWHM 29 nm, methane absorption band) spectral bands at phase angles between 5.6° and 0.01°. The resulting magnitudes can be represented as a sum of two terms, one

  13. Impact of turbulent phase noise on frequency transfer with asymmetric two-way ground-satellite coherent optical links

    Science.gov (United States)

    Robert, Clélia; Conan, Jean-Marc; Wolf, Peter

    2016-06-01

    Bidirectional ground-satellite laser links suffer from turbulence-induced scintillation and phase distortion. We study how turbulence impacts on coherent detection capacity and on the associated phase noise that restricts clock transfer precision. We evaluate the capacity to obtain a two-way cancellation of atmospheric effects despite the asymmetry between up and down link that limits the link reciprocity. For ground-satellite links, the asymmetry is induced by point-ahead angle and possibly the use, for the ground terminal, of different transceiver diameters, in reception and emission. The quantitative analysis is obtained thanks to refined end- to-end simulations under realistic turbulence and wind conditions as well as satellite cinematic. These temporally resolved simulations allow characterizing the coherent detection in terms of time series of heterodyne efficiency for different system parameters. We show that Tip/Tilt correction on ground is mandatory at reception for the down link and as a pre-compensation of the up link. Good correlation between up and down phase noise is obtained even with asymmetric apertures of the ground transceiver and in spite of pointing ahead angle. The reduction to less than 1 rad2 of the two-way differential phase noise is very promising for clock comparisons.

  14. Multifunctional Antenna Techniques

    Science.gov (United States)

    2015-11-25

    acquisition and processing server scheme. An Android smartphone application ( app ) provides the user interface for the system and can be used to select the...Dynamic Tethering of a Phased Array to an Android Smartphone , IEEE Transactions on Antennas and Propagation, (06 2013): 0. doi: 10.1109/TAP...modes of flight, and hover. The Android smartphone system was connected to a nine-axis inertial measurement unit (IMU) through an Arduino

  15. Gigahertz-band electronically scanned antennas

    Science.gov (United States)

    Bei, Nikolai A.

    2000-12-01

    Foundation and principles of radio lenses construction of centimeter and millimeter wave ranges with controlled refracting index, combining the quality of phased array antennas with optical devices are stated. Possibilities of the electronically scanning with wide-angle sector and high gain are maintained. Construction principles of scanning antennas with controlled lenses, combining the quality of phased array antennas with optical devices, are stated. Possibilities of electronically scanning with broad angle sector and high gain are maintained. Some examples of construction of antennas millimeter range of waves are listed here.

  16. A 4-element phased-array system with simultaneous spatial- and frequency-domain filtering at the antenna inputs

    NARCIS (Netherlands)

    Ghaffari, A.; Klumperink, Eric A.M.; van Vliet, Frank Edward; Nauta, Bram

    2014-01-01

    To reject strong interference in excess of 0 dBm, a 4- element LO-phase shifting phased-array receiver with 8-phase passive mixers terminated by baseband capacitors is presented. The passive mixers upconvert both the spatial and frequency domain filtering from baseband to RF, hence realizing blocker

  17. Recent Developments of Reflectarray Antennas in Dual-Reflector Configurations

    Directory of Open Access Journals (Sweden)

    Carolina Tienda

    2012-01-01

    Full Text Available Recent work on dual-reflector antennas involving reflectarrays is reviewed in this paper. Both dual-reflector antenna with a reflectarray subreflector and dual-reflectarrays antennas with flat or parabolic main reflectarray are considered. First, a general analysis technique for these two configurations is described. Second, results for beam scanning and contoured-beam applications in different frequency bands are shown and discussed. The performance and capabilities of these antennas are shown by describing some practical design cases for radar, satellite communications, and direct broadcast satellite (DBS applications.

  18. Slow-plasmon resonant nano-strip antennas

    DEFF Research Database (Denmark)

    Søndergaard, Thomas; Beermann, Jonas; Boltasseva, Alexandra

    2008-01-01

    Resonant scattering by gold nanostrip antennas due to constructive interference of counterpropagating slow surface plasmon polaritons SPPs is analyzed, including the quasistatic limit of ultrasmall antennas, and experimentally demonstrated. The phase of slow SPP reflection by strip ends is found...

  19. Slow-plasmon resonant-nanostrip antennas: Analysis and demonstration

    DEFF Research Database (Denmark)

    Søndergaard, Thomas; Beermann, J.; Boltasseva, Alexandra;

    2008-01-01

    Resonant scattering by gold nanostrip antennas due to constructive interference of counterpropagating slow surface plasmon polaritons (SPPs) is analyzed, including the quasistatic limit of ultrasmall antennas, and experimentally demonstrated. The phase of slow SPP reflection by strip ends is found...

  20. Advanced spacecraft tracking techniques using the Tracking and Data Relay Satellite System /TDRSS/

    Science.gov (United States)

    Teles, J.; Ayres, C.

    1977-01-01

    The TDRSS will consist initially of two geosynchronous satellites and a common ground station at White Sands, New Mexico. According to current schedules, operations are to begin in November 1980. The overall TDRSS will provide high and low bit-rate telemetry, commands, and satellite-to-satellite tracking services. Each Tracking and Data Relay Satellite (TDRS) will have four antenna systems for NASA use. The common ground station at White Sands will have three 18-meter K-band antennas. The tracking equipment at the ground station is required to meet the following specifications: (1) 0.1-radian root-mean-square (rms) phase noise on nondestruct Doppler measurements; (2) 10-nanosecond rms range noise; (3) 50-nanosecond maximum systematic range error. Attention is given to two-way range and Doppler measurements, the bilateration tracking of TDRS, and an experiment using differenced one-way Doppler measurements.

  1. Field-aligned-impedance-transforming ICRF antenna in the LHD

    Energy Technology Data Exchange (ETDEWEB)

    Saito, K., E-mail: saito@nifs.ac.jp; Seki, T.; Kasahara, H.; Seki, R.; Kamio, S.; Nomura, G.; Mutoh, T.

    2015-10-15

    Newly developed ion cyclotron range of frequencies (ICRF) antennas were fabricated and installed in the Large Helical Device (LHD). The antennas, called field-aligned-impedance-transforming (FAIT) antennas, were designed based on former handshake form (HAS) antennas for high power and steady-state operation. The FAIT antennas demonstrated higher loading resistance and lower temperature on ceramic feed-through than HAS antennas. Antenna impedance and injected power were measured precisely using a directional coupler installed between the impedance matching device and antenna. It was shown that an injection power of 1.8 MW or a power density of 15 MW/m{sup 2} would be possible for short-pulse discharges. The mutual coupling between two FAIT antennas is small enough, since any current phase is possible without adjusting the impedance matching device. Although the FAIT antennas are aligned in a poloidal direction, a high heating efficiency of 85% was achieved with the proper minority concentration ratio.

  2. Microstrip antenna on tunable substrate

    Science.gov (United States)

    Jose, K. A.; Varadan, Vijay K.; Varadan, Vasundara V.; Mohanan, P.

    1995-05-01

    The tunable patch antenna configurations are becoming popular and attractive in many aspects. This was mainly due to the advent of ferrite thin film technology and tunable substrate materials. The integration of monolithic microwave circuits and antennas are becoming easy today. In the development of magnetic tuning of microstrip patch on ferrite substrate is presented by Rainville and Harackewiez. Radiation characteristics of such antennas are presented by Pozer. Band width and radiation characteristics of such tunable antennas are measured and compared. Usually the substrate losses are considered in the analysis and metallization losses are assumed to be ideal. The analysis of magnetic tunable radiator including metallization and ferrite substrate losses are presented. However, all such tuning and integration of circuits and antennas are mainly on ferrite substrate due to magnetic tuning. Recently, Varadan et al. established that the BaxSr1-xTiO3 series ferroelectric materials such as Barium Strontium Titanate (BST) are well suited for microwave phase shifter applications. It could be possible to change the dielectric constant of these materials more than 50% depending on the BST composition, by changing the applied bias voltage. Also, the porosity of BST can be controlled during processing to produce dielectric constants in the range of 15 to 1500, with some trade off in tunability. In this paper, we are presenting the possibility of designing a microstrip patch antenna on such tunable substrate. Such antennas are having the major advantage of electronic tunability and compact size.

  3. X-ray observations of the impulsive phase of solar flares with the Yohkoh satellite

    Science.gov (United States)

    Phillips, Andrew

    This thesis starts with an overview of the physics of the solar corona, concentrating on X-ray emission and the plasma dynamics associated with the impulsive or rise phase of solar flares. The Yohkoh satellite is described, with a section on each major instrument on board. Analysis techniques used in the thesis are then introduced, with a section of soft X-ray spectroscopy and on the application of the Maximum Entropy Method image reconstruction technique to data from the Hard X-ray Telescope on Yohkoh. The instrumental effect known as fixed pattern noise is described, leading to a numerical model of the BCS digitisation process, which is used both to understand the limits of the detector, and to correct the data in a limited way. Alternative methods for the avoidance of fixed pattern noise are evaluated. The analysis of a solar flare with unusually large soft X-ray blue shifts is then performed. Physical parameters of the plasma during the initial stages of the flare are derived, which are used in an energy balance calculation. Agreement is found between the energy in nonthermal electrons and that contained in the coronal plasma, supporting the nonthermal beam driven chromospheric evaporation theory of impulsive flares. The location of superhot plasma in two impulsive flares and one hot thermal flare is then investigated. Superhot plasma is found to be located close to the chromosphere, and related to the nonthermal burst in the two impulsive flares. Superhot plasma in the hot thermal flare is distributed uniformly throughout the loop. The differences are explained as being due to the different energy transport processes active in each type of flare.

  4. Conformal, Transparent Printed Antenna Developed for Communication and Navigation Systems

    Science.gov (United States)

    Lee, Richard Q.; Simons, Rainee N.

    1999-01-01

    Conformal, transparent printed antennas have advantages over conventional antennas in terms of space reuse and aesthetics. Because of their compactness and thin profile, these antennas can be mounted on video displays for efficient integration in communication systems such as palmtop computers, digital telephones, and flat-panel television displays. As an array of multiple elements, the antenna subsystem may save weight by reusing space (via vertical stacking) on photovoltaic arrays or on Earth-facing sensors. Also, the antenna could go unnoticed on automobile windshields or building windows, enabling satellite uplinks and downlinks or other emerging high-frequency communications.

  5. Technique for Radiometer and Antenna Array Calibration with Two Antenna Noise Diodes

    Science.gov (United States)

    Srinivasan, Karthik; Limaye, Ashutosh; Laymon, Charles; Meyer, Paul

    2011-01-01

    This paper presents a new technique to calibrate a microwave radiometer and phased array antenna system. This calibration technique uses a radiated noise source in addition to an injected noise sources for calibration. The plane of reference for this calibration technique is the face of the antenna and therefore can effectively calibration the gain fluctuations in the active phased array antennas. This paper gives the mathematical formulation for the technique and discusses the improvements brought by the method over the existing calibration techniques.

  6. In-orbit performance evaluation of multiple-beam antenna on satellites%星载多波束天线在轨性能评估方法

    Institute of Scientific and Technical Information of China (English)

    尹术懿; 何元智; 尹浩

    2012-01-01

    为解决星载多波束天线测试波束数量大、在轨测试成本高、性能评估困难等问题,在合成多波束形成原理基础上,通过分析天线系统中波束成形网络和馈源阵之间的映射关系,提出了一种以馈源阵性能为基础评估天线性能的策略.采用最小二乘估计法,对馈源性能估计中典型波束的数量、组合方式选取与平均估计误差等问题进行了分析,并通过仿真实验得出了典型波束数量、组合方式、平均估计误差三者间的定量关系以及在实际条件下,测试波束数量的选取范围和波束最佳组合方式,为高效地处理在轨测试数据提供了一种低复杂度的分析方法,对实际系统中星载多波束天线在轨测试具有重要意义.%To solve such problems as the high in-orbit testing cost and the difficult evaluation of Multiple-Beam Antenna with large number of beams,an antenna evaluation strategy based on the feed properties was proposed,through the analysis of the beam forming principle of the composite beams and exploration of the relation between the beam forming network and the feed Source Array. By employing the least squares evaluation method,the typical beam selection,combination and average estimation error for the feed properties were analyzed. The simulation results show the quantitative correlation among the typical beam number,combination and the average estimation error,and the selection of the typical test beam number and the optimal test beams sequence in actual conditions. The proposed method can provide an excellent reference value to process the In-Orbit testing data efficiency and reduce the complexity of finding the optimal test beams sequence for a practical system.

  7. Superluminal antenna

    Energy Technology Data Exchange (ETDEWEB)

    Singleton, John; Earley, Lawrence M.; Krawczyk, Frank L.; Potter, James M.; Romero, William P.; Wang, Zhi-Fu

    2017-03-28

    A superluminal antenna element integrates a balun element to better impedance match an input cable or waveguide to a dielectric radiator element, thus preventing stray reflections and consequent undesirable radiation. For example, a dielectric housing material can be used that has a cutout area. A cable can extend into the cutout area. A triangular conductor can function as an impedance transition. An additional cylindrical element functions as a sleeve balun to better impedance match the radiator element to the cable.

  8. RF MEMS reconfigurable triangular patch antenna.

    Energy Technology Data Exchange (ETDEWEB)

    Christodoulou, Christos George (The University of New Mexico, Albuquerque, NM); Nordquist, Christopher Daniel; Feldner, Lucas Matthew

    2005-07-01

    A Ka-band RF MEMS enabled frequency reconfigurable triangular microstrip patch antenna has been designed for monolithic integration with RF MEMS phase shifters to demonstrate a low-cost monolithic passive electronically scanned array (PESA). This paper introduces our first prototype reconfigurable triangular patch antenna currently in fabrication. The aperture coupled patch antenna is fabricated on a dual-layer quartz/alumina substrate using surface micromachining techniques.

  9. RF MEMS reconfigurable triangular patch antenna.

    Energy Technology Data Exchange (ETDEWEB)

    Nordquist, Christopher Daniel; Christodoulou, Christos George (University of New Mexico, Albuquerque, NM); Feldner, Lucas Matthew

    2005-01-01

    A Ka-band RF MEMS enabled frequency reconfigurable triangular microstrip patch antenna has been designed for monolithic integration with RF MEMS phase shifters to demonstrate a low-cost monolithic passive electronically scanned array (PESA). This paper introduces our first prototype reconfigurable triangular patch antenna currently in fabrication. The aperture coupled patch antenna is fabricated on a dual-layer quartz/alumina substrate using surface micromachining techniques.

  10. UWB planar antenna technology

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Recent developments of the ultra-wideband(UWB)planar antennas are reviewed,where the progress in UWB plate monopole antennas,UWB printed monopole antennas and the UWB printed slot antennas is introduced and compared.In addition,the UWB printed antennas with the band-notched functions are also presented.

  11. Theoretical analysis of ion cyclotron range of frequency antenna array for HT-7U

    Institute of Scientific and Technical Information of China (English)

    Zhang Xin-Jun; Qin Cheng-Ming; Zhao Yan-Ping

    2005-01-01

    This paper considers the coupling analysis of phased antenna array designed to excite fast wave in the ion cyclotron range of frequency. The coupling of the antenna is calculated in slab geometry. The coupling code based on the variational principle gives the self-consistent current flowing in the antenna, this method has been extended so that it can be applied to a phased antenna array. As an example, this paper analyses the coupling prosperities of a 2×2phased antenna array. It gives the optimum geometry of antenna array. The fields excited at plasma surface are found to more or less correspond to the antenna current phasing.

  12. SPS phase control system performance via analytical simulation

    Science.gov (United States)

    Lindsey, W. C.; Kantak, A. V.; Chie, C. M.; Booth, R. W. D.

    1979-01-01

    A solar power satellite transmission system which incorporates automatic beam forming, steering, and phase control is discussed. The phase control concept centers around the notation of an active retrodirective phased array as a means of pointing the beam to the appropriate spot on Earth. The transmitting antenna (spacetenna) directs the high power beam so that it focuses on the ground-based receiving antenna (rectenna). A combination of analysis and computerized simulation was conducted to determine the far field performance of the reference distribution system, and the beam forming and microwave power generating systems.

  13. A Printable Silicon Nano-Field Effect Transistor with High Operating Frequency for Large-Area Deployable Active Phased-Array Antennas Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Flexible electronic circuits can be easily integrated with large area (>10m aperture), inflatable antennas to provide distributed control and processing...

  14. Design and fabrication of miniature antenna based on silicon substrate for wireless communications

    Institute of Scientific and Technical Information of China (English)

    GUO XingLong; JIN Yan; LIU Lei; OUYANG WeiXia; LAI ZongSheng

    2008-01-01

    In this paper, a novel compact CPW-fed slot small antenna was designed and fab-ricated on high-resistivity silicon (HR-Si) by micro-electronics process. The results of simulation are consistent with results of measurement for the antenna. The mode of the antenna is vertical and horizontal bidirectional radiations. The gain of antenna is 2.5 dB, and the resonance frequency approximately is 3 GHz. This fab-rication can be compatible with antenna integration and CMOS process. The pa-rameters of this antenna are for reference radar antenna system of Unmanned Ae-rial Vehicles (UAV), satellite transmission, and communication.

  15. Magnetic antenna excitation of whistler modes. IV. Receiving antennas and reciprocity

    Energy Technology Data Exchange (ETDEWEB)

    Stenzel, R. L., E-mail: stenzel@physics.ucla.edu; Urrutia, J. M. [Department of Physics and Astronomy, University of California, Los Angeles, California 90095-1547 (United States)

    2015-07-15

    Antenna radiation patterns are an important property of antennas. Reciprocity holds in free space and the radiation patterns for exciting and receiving antennas are the same. In anisotropic plasmas, radiation patterns are complicated by the fact that group and phase velocities differ and certain wave properties like helicity depend on the direction of wave propagation with respect to the background magnetic field B{sub 0}. Interference and wave focusing effects are different than in free space. Reciprocity does not necessarily hold in a magnetized plasma. The present work considers the properties of various magnetic antennas used for receiving whistler modes. It is based on experimental data from exciting low frequency whistler modes in a large uniform laboratory plasma. By superposition of linear waves from different antennas, the radiation patterns of antenna arrays are derived. Plane waves are generated and used to determine receiving radiation patterns of different receiving antennas. Antenna arrays have radiation patterns with narrow lobes, whose angular position can be varied by physical rotation or electronic phase shifting. Reciprocity applies to broadside antenna arrays but not to end fire arrays which can have asymmetric lobes with respect to B{sub 0}. The effect of a relative motion between an antenna and the plasma has been modeled by the propagation of a short wave packet moving along a linear antenna array. An antenna moving across B{sub 0} has a radiation pattern characterized by an oscillatory “whistler wing.” A receiving antenna in motion can detect any plane wave within the group velocity resonance cone. The radiation pattern also depends on loop size relative to the wavelength. Motional effects prevent reciprocity. The concept of the radiation pattern loses its significance for wave packets since the received signal does not only depend on the antenna but also on the properties of the wave packet. The present results are of fundamental

  16. Transportable setup for amplifier phase fidelity measurements

    OpenAIRE

    Troebs, Michael; Bogan, C.; Barke, S.; Kuehn, G.; Reiche, J.; Heinzel, Gerhard; Danzmann, Karsten

    2015-01-01

    One possible laser source for the Laser Interferometer Space Antenna (LISA) consists of an Ytterbium-doped fiber amplifier originally developed for inter-satellite communication, seeded by the laser used for the technology demonstrator mission LISA Pathfinder. LISA needs to transmit clock information between its three spacecraft to correct for phase noise between the clocks on the individual spacecraft. For this purpose phase modulation sidebands at GHz frequencies will be imprinted on the la...

  17. Mobile satellite communications technology - A summary of NASA activities

    Science.gov (United States)

    Dutzi, E. J.; Knouse, G. H.

    1986-01-01

    Studies in recent years indicate that future high-capacity mobile satellite systems are viable only if certain high-risk enabling technologies are developed. Accordingly, NASA has structured an advanced technology development program aimed at efficient utilization of orbit, spectrum, and power. Over the last two years, studies have concentrated on developing concepts and identifying cost drivers and other issues associated with the major technical areas of emphasis: vehicle antennas, speech compression, bandwidth-efficient digital modems, network architecture, mobile satellite channel characterization, and selected space segment technology. The program is now entering the next phase - breadboarding, development, and field experimentation.

  18. Optical antennas and plasmonics

    OpenAIRE

    Park, Q-Han

    2009-01-01

    Optical antenna is a nanoscale miniaturization of radio or microwave antennas that is also governed by the rule of plasmonics. We introduce various types of optical antenna and make an overview of recent developments in optical antenna research. The role of local and surface plasmons in optical antenna is explained through antenna resonance and resonance conditions for specific metal structures are explicitly obtained. Strong electric field is shown to exist within a highly localized region o...

  19. Antenna Showers with Hadronic Initial States

    CERN Document Server

    Ritzmann, M; Skands, P

    2013-01-01

    We present an antenna shower formalism including contributions from initial-state partons and corresponding backwards evolution. We give a set of phase-space maps and antenna functions for massless partons which define a complete shower formalism suitable for computing observables with hadronic initial states. We focus on the initial-state components: initial-initial and initial-final antenna configurations. The formalism includes comprehensive possibilities for uncertainty estimates. We report on some preliminary results obtained with an implementation in the Vincia antenna-shower framework.

  20. Fresnel zones for ground-based antennas

    DEFF Research Database (Denmark)

    Andersen, J. Bach

    1964-01-01

    The ordinary Fresnel zone concept is modified to include the influence of finite ground conductivity. This is important for ground-based antennas because the influence on the radiation pattern of irregularities near the antenna is determined by the amplitude and phase of the groundwave. A new...

  1. Antennas in inhomogeneous media

    CERN Document Server

    Galejs, Janis; Fock, V A; Wait, J R

    2013-01-01

    Antennas in Inhomogeneous Media details the methods of analyzing antennas in such inhomogeneous media. The title covers the complex geometrical configurations along with its variational formulations. The coverage of the text includes various conditions the antennas are subjected to, such as antennas in the interface between two media; antennas in compressible isotropic plasma; and linear antennas in a magnetoionic medium. The selection also covers insulated loops in lossy media; slot antennas with a stratified dielectric or isotropic plasma layers; and cavity-backed slot antennas. The book wil

  2. Design and layout of rectangular waveguide horns antennas

    Science.gov (United States)

    Fasold, D.; Pecher, H.

    Theoretical basis of waveguide horn antennas (WHA) is outlined. Applicable design curves, such as nomograms for determining gain and a diagram for laying out necessary waveguide dimensions, are given. Use of WHA designs in satellite radio and television systems is discussed. Antenna radiation pattern calculations are treated and optimization problems are dealt with. Based on design feasibility results, a laboratory model of a transmitter antenna for TV-SAT was built. The equipment, an elliptical waveguide horn design, demonstrates satisfactory performance.

  3. Sidelobe Canceling for Optimization of Reconfigurable Holographic Metamaterial Antenna

    OpenAIRE

    Johnson, Mikala C.; Brunton, Steven L.; Kutz, J Nathan; Kundtz, Nathan B.

    2014-01-01

    Accurate and efficient methods for beam-steering of holographic metamaterial antennas is of critical importance for enabling consumer usage of satellite data capacities. We develop an optimization algorithm capable of performing adaptive, real-time control of antenna patterns while operating in dynamic environments. Our method provides a first analysis of the antenna pattern optimization problem in the context of metamaterials and for the purpose of directing the central beam and significantl...

  4. A comprehensive simulation of weak-light phase-locking for space-borne gravitational wave antenna

    Institute of Scientific and Technical Information of China (English)

    DONG YuHui; LIU HeShan; LUO ZiRen; LI YuQiong; JIN Gang

    2016-01-01

    A comprehensive simulation was performed to better understand the impacts and effects of the additional technical noises on weak-light phase-locking for LISA.The result showed that the phase of the slave laser tracked well with the received transmitting light under different noise level,and the locking precision was limited by the phase readout noise when the laser frequency noise and clock jitter noise were removed.This result was then confirmed by a benchtop experimental test.The required LISA noise floor was recovered from the simulation which proved the validity of the simulation program.In order to convert the noise function into real time data with random characteristics,an algorism based on Fourier transform was also invented.

  5. Advanced Communications Technology Satellite (ACTS). Phase 1: Industrial/academic experimenters

    Science.gov (United States)

    Maisel, James E.; Nowlin, Robert W.

    1992-01-01

    This report presents the work done at Arizona State University under the ACTS Experimenters Program. The main thrust of the Program was to develop experiments to test, evaluate, and prove the commercial worthiness of the ACTS satellite which is scheduled for launch in 1993. To accomplish this goal, meetings were held with various governmental, industrial, and academic units to discuss the ACTS satellite and its technology and possible experiments that would generate industrial interest and support for ASU's efforts. Several local industries generated several experiments of their own. The investigators submitted several experiments of educational, medical, commercial, and technical value and interest. The disposition of these experimental proposals is discussed in this report.

  6. MUTUAL COUPLING REDUCTION BETWEEN MICROSTRIP ANTENNAS USING ELECTROMAGNETIC BANDGAP STRUCTURE

    Directory of Open Access Journals (Sweden)

    G.N. Gaikwad

    2011-03-01

    Full Text Available When the number of antenna elements is placed in forming the arrays, mutual coupling between the antenna elements is a critical issue. This is particularly concern in phase array antennas. Mutual coupling is a potential source of performance degradation in the form of deviation of the radiation pattern from the desired one, gain reduction due to excitation of surface wave, increased side lobe levels etc. EBG (Electromagnetic Band Gap structure (also called as Photonic Bandgap Structure PBG not only enhances the performance of the patch antennas but also provides greater amount of isolation when placed between the microstrip arrays. This greatly reduces the mutual coupling between the antenna elements. The radiation efficiency, gain, antenna efficiency, VSWR, frequency, directivity etc greatly improves over the conventional patch antennas using EBG. The EBG structure and normal patch antenna is simulated using IE3D antenna simulation software.

  7. Radiated EMC& EMI Management During Design Qualification and Test Phases on LEO Satellites Constellation

    Science.gov (United States)

    Blondeaux, H.; Terral, M.; Gutierrez-Galvan, R.; Baud, C.

    2016-05-01

    The aim of the proposed paper is to present the global radiated EMC/EMI approach applied by Thales Alenia Space in the frame of a telecommunication Low Earth Orbit (LEO) satellites constellation program. The paper will present this approach in term of analyses, of specific characterisation and of sub-system and satellite tests since first design reviews up-to satellite qualification tests on Prototype Flight Model (PFM) and to production tests on reduced FMs. The global aim is : 1 - to reduce risk and cost (units EMC delta qualification, EMC tests at satellite level for the 81 Space Vehicles (SV) through appropriated EMC analyses (in term of methodologies and contours) provided in the frame of design reviews.2 - to early anticipate potential critical case to reduce the impact in term of engineering/qualification/test extra cost and of schedule.3 - to secure/assure the payload and SV design/layout.4 - to define and optimize the EMC/EMI test campaigns to be performed on Prototype Flight Model (PFM) for complete qualification and on some FMs for industrial qualification/validation.The last part of the paper is dedicated to system Bite Error Rate (BER) functional test performed on PFM SV to demonstrate the final compatibility between the three on-board payloads and to the Internal EMC tests performed on PFM and some FMs to demonstrate the SV panel RF shielding efficiency before and after environmental tests and the Thales Alenia Space (TAS) and Orbital AKT (OATK) workmanships reproducibility.

  8. Estimation of Satellite PCO Offsets for BeiDou based on MGEX Net Solution

    Science.gov (United States)

    Yize, Zhang; Junping, Chen; Bin, Wu; Jiexian, Wang

    2015-04-01

    BeiDou Satellite Navigation System currently has a total 14 satellites including GEO/IGSO/MEO satellites and providing a regional PNT service. Due to a lack of publicly available antenna phase center offsets (PCO) for the BeiDou satellites, conventional values of (+0.6 m, 0.0 m, +1.1 m) are recommended for orbit and clock determination of the GEO/IGSO/MEO satellites, which needs to be further estimation and refinement. In this paper, we propose a multi-GNSS network solution for the estimation of BeiDou satellite PCO. More than 35 ground stations of International GNSS MGEX tracking network are used to determine the BeiDou satellite PCO. In this strategy, the GPS and BeiDou satellite orbits and clocks are derived from IGS final products, and GPS satellite PCO and PCV are fixed according to igs08.atx. The BeiDou satellites PCO are estimated together with the station clock, troposphere delay and LC combination ambiguity parameter. Result shows that the RMS of phase residuals for all stations is 1.8cm and is 1.6m for code residual, respectively. The estimated PCO is different for each satellite. Appling the new PCO for precise point positioning, we found that the positioning error improves from 6cm to 2cm in height.

  9. Aligning a Receiving Antenna Array to Reduce Interference

    Science.gov (United States)

    Jongeling, Andre P.; Rogstad, David H.

    2009-01-01

    A digital signal-processing algorithm has been devised as a means of aligning (as defined below) the outputs of multiple receiving radio antennas in a large array for the purpose of receiving a desired weak signal transmitted by a single distant source in the presence of an interfering signal that (1) originates at another source lying within the antenna beam and (2) occupies a frequency band significantly wider than that of the desired signal. In the original intended application of the algorithm, the desired weak signal is a spacecraft telemetry signal, the antennas are spacecraft-tracking antennas in NASA s Deep Space Network, and the source of the wide-band interfering signal is typically a radio galaxy or a planet that lies along or near the line of sight to the spacecraft. The algorithm could also afford the ability to discriminate between desired narrow-band and nearby undesired wide-band sources in related applications that include satellite and terrestrial radio communications and radio astronomy. The development of the present algorithm involved modification of a prior algorithm called SUMPLE and a predecessor called SIMPLE. SUMPLE was described in Algorithm for Aligning an Array of Receiving Radio Antennas (NPO-40574), NASA Tech Briefs Vol. 30, No. 4 (April 2006), page 54. To recapitulate: As used here, aligning signifies adjusting the delays and phases of the outputs from the various antennas so that their relatively weak replicas of the desired signal can be added coherently to increase the signal-to-noise ratio (SNR) for improved reception, as though one had a single larger antenna. Prior to the development of SUMPLE, it was common practice to effect alignment by means of a process that involves correlation of signals in pairs. SIMPLE is an example of an algorithm that effects such a process. SUMPLE also involves correlations, but the correlations are not performed in pairs. Instead, in a partly iterative process, each signal is appropriately weighted

  10. Research in large adaptive antenna arrays

    Science.gov (United States)

    Berkowitz, R. S.; Dzekov, T.

    1976-01-01

    The feasibility of microwave holographic imaging of targets near the earth using a large random conformal array on the earth's surface and illumination by a CW source on a geostationary satellite is investigated. A geometrical formulation for the illuminator-target-array relationship is applied to the calculation of signal levels resulting from L-band illumination supplied by a satellite similar to ATS-6. The relations between direct and reflected signals are analyzed and the composite resultant signal seen at each antenna element is described. Processing techniques for developing directional beam formation as well as SNR enhancement are developed. The angular resolution and focusing characteristics of a large array covering an approximately circular area on the ground are determined. The necessary relations are developed between the achievable SNR and the size and number of elements in the array. Numerical results are presented for possible air traffic surveillance system. Finally, a simple phase correlation experiment is defined that can establish how large an array may be constructed.

  11. Coherence and phase structure of compressional ULF waves at low-Earth-orbit observed by the Swarm satellites

    Science.gov (United States)

    Heilig, Balázs; Sutcliffe, Peter R.

    2016-04-01

    Different types of ultra low frequency (ULF waves), such as dayside compressional Pc3-Pc4 waves, Pc2 and Pc1 waves, Pc3-Pc4 field line resonances, night side and day side Pi2s, etc. have been successfully identified in the topside ionosphere. ULF observations in this region can help us to understand the wave structure in the magnetosphere, wave propagation, and also the effects of the ionosphere (transmission, reflection, mode conversion). Because of the fast orbiting of the LEO satellites Fourier analysis is not applicable, special techniques (wavelet analysis, maximum entropy method) are needed to resolve ULF signals, as well as to discriminate between spatial and wave structures. In this paper we present results of a study of Pc3 compressional waves observed at low-Earth-orbit (LEO) by the Swarm satellites. The particular emphasis has been to investigate the distribution of wave coherence and phase difference as functions of magnetic latitude and local time. This is the first time that a study of this nature has been carried out using magnetic field data from multiple LEO satellites. We believe that our study provides the first observational evidence to support the prediction by the inductive thin ionosphere model that incident Alfvén mode waves are partially converted into compressional mode waves by the ionosphere.

  12. Comparison of the peak resolution and the stationary phase retention between the satellite and the planetary motions using the coil satellite centrifuge with counter-current chromatographic separation of 4-methylumbelliferyl sugar derivatives.

    Science.gov (United States)

    Shinomiya, Kazufusa; Zaima, Kazumasa; Harada, Yukina; Yasue, Miho; Harikai, Naoki; Tokura, Koji; Ito, Yoichiro

    2017-01-20

    Coil satellite centrifuge (CSC) produces the complex satellite motion consisting of the triplicate rotation of the coiled column around three axes including the sun axis (the angular velocity, ω1), the planet axis (ω2) and the satellite axis (the central axis of the column) (ω3) according to the following formula: ω1=ω2+ω3. Improved peak resolution in the separation of 4-methylumbelliferyl sugar derivatives was achieved using the conventional multilayer coiled columns with ethyl acetate/1-butanol/water (3: 2: 5, v/v) for the lower mobile phase at the combination of the rotation speeds (ω1, ω2, ω3)=(300, 150, 150rpm), and (1:4:5, v/v) for the upper mobile phase at (300:100:200rpm). The effect of the satellite motion on the peak resolution and the stationary phase retention was evaluated by each CSC separation with the different rotation speeds of ω2 and ω3 under the constant revolution speed at ω1=300rpm. With the lower mobile phase, almost constant peak resolution and stationary phase retention were yielded regardless of the change of ω2 and ω3, while with the upper mobile phase these two values were sensitively varied according to the different combination of ω2 and ω3. For example, when ω2=147 or 200rpm is used, no stationary phase was retained in the coiled column while ω2=150rpm could retain enough volume of stationary phase for separation. On the other hand, the combined rotation speeds at (ω1, ω2, ω3)=(300, 300, 0rpm) or (300, 0, 300rpm) produced insufficient peak resolution regardless of the choice of the mobile phase apparently due to the lack of rotation speed except at (300, 0, 300rpm) with the upper mobile phase. At lower rotation speed of ω1=300rpm, better peak resolution and stationary phase retention were obtained by the satellite motion (ω3) than by the planetary motion (ω2), or ω3>ω2. The effect of the hydrophobicity of the two-phase solvent systems on the stationary phase retention was further examined using the n

  13. VSOP-2 Antenna and its Structure

    Science.gov (United States)

    Higuchi, K.; Kishimoto, N.; Mizuno, T.; Kawahara, K.; Tachikawa, S.; Murata, Y.; Tsuboi, M.; Ogawa, H.; Kimura, S.; Ujihara, H.; Meguro, A.; Tanaka, H.; Yoshihara, M.; Iikura, S.

    2009-08-01

    To achieve scientific improvements from VSOP (HALCA) to VSOP-2 (ASTRO-G), the satellite design incorporates the engineering characteristics of a large-scale deployable antenna of offset Cassegrain type with observation bands of 8, 22, and 43 GHz. The antenna subsystem requires the surface accuracy of 0.4mm RMS on the main reflector named LDR (Large-scale Deployable Reflector) of about 9m in diameter. An off-axis paraboloid reflector is adopted to achieve this surface accuracy for millimeter-wave observation. The main reflector is composed of seven deployable modular antennas, and each of the modules employs a new idea of radial-rib/hoop-cable reflector construction to stretch metal mesh and to satisfy the required surface accuracy. The deployment mechanism employs most of the LDR technology developed for JAXA's ETS-VIII satellite, which was launched in December 2006, and both of the two antennas on the ETS-VIII deployed successfully on orbit. Some prototype models of one module have been made to investigate the surface accuracy. In addition, the antenna will have a two-axis adjustment mechanism for the main reflector, and a three-axis adjustment mechanism for the sub-reflector in order to optimize the antenna gain after deployment in orbit.

  14. Computer controlled antenna system

    Science.gov (United States)

    Raumann, N. A.

    1972-01-01

    The application of small computers using digital techniques for operating the servo and control system of large antennas is discussed. The advantages of the system are described. The techniques were evaluated with a forty foot antenna and the Sigma V computer. Programs have been completed which drive the antenna directly without the need for a servo amplifier, antenna position programmer or a scan generator.

  15. Optical antenna gain. I - Transmitting antennas

    Science.gov (United States)

    Klein, B. J.; Degnan, J. J.

    1974-01-01

    The gain of centrally obscured optical transmitting antennas is analyzed in detail. The calculations, resulting in near- and far-field antenna gain patterns, assume a circular antenna illuminated by a laser operating in the TEM-00 mode. A simple polynomial equation is derived for matching the incident source distribution to a general antenna configuration for maximum on-axis gain. An interpretation of the resultant gain curves allows a number of auxiliary design curves to be drawn that display the losses in antenna gain due to pointing errors and the cone angle of the beam in the far field as a function of antenna aperture size and its central obscuration. The results are presented in a series of graphs that allow the rapid and accurate evaluation of the antenna gain which may then be substituted into the conventional range equation.

  16. Optical antenna gain. 1: transmitting antennas.

    Science.gov (United States)

    Klein, B J; Degnan, J J

    1974-09-01

    The gain of centrally obscured optical transmitting antennas is analyzed in detail. The calculations, resulting in near- and far-field antenna gain patterns, assume a circular antenna illuminated by a laser operating in the TEM(00) mode. A simple polynomial equation is derived for matching the incident source distribution to a general antenna configuration for maximum on-axis gain. An interpretation of the resultant gain curves allows a number of auxiliary design curves to be drawn that display the losses in antenna gain due to pointing errors and the cone angle of the beam in the far field as a function of antenna aperture size and its central obscuration. The results are presented in a series of graphs that allow the rapid and accurate evaluation of the antenna gain which may then be substituted into the conventional range equation.

  17. Advanced Antenna for Digital Beamforming SAR Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Develop a wideband (500 MHz) L-band phased-array antenna for airborne Synthetic Aperture Radar (SAR) applications based on a novel approach that will make possible...

  18. Slot Coupled Patch Array Antenna Technology Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed project is an antenna array whose beam is controlled digitally. The Phase 1 effort will assess the method needed to achieve the gain, bandwidth, and...

  19. An interhemispheric comparison of GPS phase scintillation with auroral emission observed at the South Pole and from the DMSP satellite

    Directory of Open Access Journals (Sweden)

    Paul Prikryl

    2013-06-01

    Full Text Available The global positioning system (GPS phase scintillation caused by high-latitude ionospheric irregularities during an intense high-speed stream (HSS of the solar wind from April 29 to May 5, 2011, was observed using arrays of GPS ionospheric scintillation and total electron content monitors in the Arctic and Antarctica. The one-minute phase-scintillation index derived from the data sampled at 50 Hz was complemented by a proxy index (delta phase rate obtained from 1-Hz GPS data. The scintillation occurrence coincided with the aurora borealis and aurora australis observed by an all-sky imager at the South Pole, and by special sensor ultraviolet scanning imagers on board satellites of the Defense Meteorological Satellites Program. The South Pole (SP station is approximately conjugate with two Canadian High Arctic Ionospheric Network stations on Baffin Island, Canada, which provided the opportunity to study magnetic conjugacy of scintillation with support of riometers and magnetometers. The GPS ionospheric pierce points were mapped at their actual or conjugate locations, along with the auroral emission over the South Pole, assuming an altitude of 120 km. As the aurora brightened and/or drifted across the field of view of the all-sky imager, sequences of scintillation events were observed that indicated conjugate auroras as a locator of simultaneous or delayed bipolar scintillation events. In spite of the greater scintillation intensity in the auroral oval, where phase scintillation sometimes exceeded 1 radian during the auroral break-up and substorms, the percentage occurrence of moderate scintillation was highest in the cusp. Interhemispheric comparisons of bipolar scintillation maps show that the scintillation occurrence is significantly higher in the southern cusp and polar cap.

  20. PBG based terahertz antenna for aerospace applications

    CERN Document Server

    Choudhury, Balamati; Jha, Rakesh Mohan

    2016-01-01

    This book focuses on high-gain antennas in the terahertz spectrum and their optimization. The terahertz spectrum is an unallocated EM spectrum, which is being explored for a number of applications, especially to meet increasing demands of high data rates for wireless space communications. Space communication systems using the terahertz spectrum can resolve the problems of limited bandwidth of present wireless communications without radio-frequency interference. This book describes design of such high-gain antennas and their performance enhancement using photonic band gap (PBG) substrates. Further, optimization of antenna models using evolutionary algorithm based computational engine has been included. The optimized high-performance compact antenna may be used for various wireless applications, such as inter-orbital communications and on-vehicle satellite communications.

  1. Comparison Analysis of Micro/Mini-Channel Cold Plate on a Phased Array Antenna%微/小通道冷板在某型相控阵天线上的对比分析

    Institute of Scientific and Technical Information of China (English)

    翁夏

    2014-01-01

    微通道换热是近年来电子机械工程抗恶劣环境研究的热点之一。由于其具有良好的换热特性,现在逐渐被应用于高热流密度电子设备的冷却散热系统设计之中。相控阵天线具有热源集中、热流密度极高等特点。文中将新型微通道冷板与某型相控阵天线进行有机结合,提出了一种新的相控阵天线冷却方式。同时,通过基于有限体积法的仿真分析表明,微通道冷板相较于小通道冷板更有利于控制天线中T/R模块的温度。%Heat convection in micro-channel is one of the focused research points in the field of anti-adverse environment in electro-mechanical engineering .Micro-channel heat convection is gradually applied to cooling systems of high heat flux electronic equipment because of its good heat transfer property .Phased array antenna has the characteristics of concentrated heat source and extremely high heat flux .A new type of micro-channel cold plate and a type of phased array antenna are organically integrated , and a new cooling method for phased array antenna is presented .Meanwhile ,according to the numerical simulation based on finite volume method ( FVM) , micro-channel cold plates are more advantageous than mini-channel cold plates for controlling the temperature of T/R modules in antenna .

  2. Magnetic antenna excitation of whistler modes. II. Antenna arrays

    Energy Technology Data Exchange (ETDEWEB)

    Stenzel, R. L.; Urrutia, J. M. [Department of Physics and Astronomy, University of California, Los Angeles, California 90095-1547 (United States)

    2014-12-15

    The excitation of whistler modes from magnetic loop antennas has been investigated experimentally. The field topology of the excited wave driven by a single loop antenna has been measured for different loop orientations with respect to the uniform background field. The fields from two or more antennas at different locations are then created by superposition of the single-loop data. It is shown that an antenna array can produce nearly plane waves which cannot be achieved with single antennas. By applying a phase shift along the array, oblique wave propagation is obtained. This allows a meaningful comparison with plane wave theory. The Gendrin mode and oblique cyclotron resonance are demonstrated. Wave helicity and polarization in space and time are demonstrated and distinguished from the magnetic helicity of the wave field. The superposition of two oblique plane whistler modes produces in a “whistler waveguide” mode whose polarization and helicity properties are explained. The results show that single point measurements cannot properly establish the wave character of wave packets. The laboratory observations are relevant for excitation and detection of whistler modes in space plasmas.

  3. GNSS Carrier Phase Integer Ambiguity Resolution with Camera and Satellite images

    Science.gov (United States)

    Henkel, Patrick

    2015-04-01

    Ambiguity Resolution is the key to high precision position and attitude determination with GNSS. However, ambiguity resolution of kinematic receivers becomes challenging in environments with substantial multipath, limited satellite availability and erroneous cycle slip corrections. There is a need for other sensors, e.g. inertial sensors that allow an independent prediction of the position. The change of the predicted position over time can then be used for cycle slip detection and correction. In this paper, we provide a method to improve the initial ambiguity resolution for RTK and PPP with vision-based position information. Camera images are correlated with geo-referenced aerial/ satellite images to obtain an independent absolute position information. This absolute position information is then coupled with the GNSS and INS measurements in an extended Kalman filter to estimate the position, velocity, acceleration, attitude, angular rates, code multipath and biases of the accelerometers and gyroscopes. The camera and satellite images are matched based on some characteristic image points (e.g. corners of street markers). We extract these characteristic image points from the camera images by performing the following steps: An inverse mapping (homogenous projection) is applied to transform the camera images from the driver's perspective to bird view. Subsequently, we detect the street markers by performing (a) a color transformation and reduction with adaptive brightness correction to focus on relevant features, (b) a subsequent morphological operation to enhance the structure recognition, (c) an edge and corner detection to extract feature points, and (d) a point matching of the corner points with a template to recognize the street markers. We verified the proposed method with two low-cost u-blox LEA 6T GPS receivers, the MPU9150 from Invensense, the ASCOS RTK corrections and a PointGrey camera. The results show very precise and seamless position and attitude

  4. Computer-Automated Evolution of Spacecraft X-Band Antennas

    Science.gov (United States)

    Lohn, Jason D.; Homby, Gregory S.; Linden, Derek S.

    2010-01-01

    A document discusses the use of computer- aided evolution in arriving at a design for X-band communication antennas for NASA s three Space Technology 5 (ST5) satellites, which were launched on March 22, 2006. Two evolutionary algorithms, incorporating different representations of the antenna design and different fitness functions, were used to automatically design and optimize an X-band antenna design. A set of antenna designs satisfying initial ST5 mission requirements was evolved by use these algorithms. The two best antennas - one from each evolutionary algorithm - were built. During flight-qualification testing of these antennas, the mission requirements were changed. After minimal changes in the evolutionary algorithms - mostly in the fitness functions - new antenna designs satisfying the changed mission requirements were evolved and within one month of this change, two new antennas were designed and prototypes of the antennas were built and tested. One of these newly evolved antennas was approved for deployment on the ST5 mission, and flight-qualified versions of this design were built and installed on the spacecraft. At the time of writing the document, these antennas were the first computer-evolved hardware in outer space.

  5. Odyssey, an optimized personal communications satellite system

    Science.gov (United States)

    Rusch, Roger J.

    Personal communications places severe demands on service providers and transmission facilities. Customers are not satisfied with the current levels of service and want improvements. Among the characteristics that users seek are: lower service rates, hand held convenience, acceptable time delays, ubiquitous service, high availability, reliability, and high quality. The space industry is developing commercial space systems for providing mobile communications to personal telephones. Provision of land mobile satellite service is fundamentally different from the fixed satellite service provided by geostationary satellites. In fixed service, the earth based antennas can depend on a clear path from user to satellite. Mobile users in a terrestrial environment commonly encounter blockage due to vegetation, terrain or buildings. Consequently, high elevation angles are of premium value. TRW studied the issues and concluded that a Medium Earth Orbit constellation is the best solution for Personal Communications Satellite Service. TRW has developed Odyssey, which uses twelve satellites in medium altitude orbit to provide personal communications satellite service. The Odyssey communications system projects a multibeam antenna pattern to the Earth. The attitude control system orients the satellites to ensure constant coverage of land mass and coastal areas. Pointing can be reprogrammed by ground control to ensure optimized coverage of the desired service areas. The payload architecture features non-processing, "bent pipe" transponders and matrix amplifiers to ensure dynamic power delivery to high demand areas. Circuit capacity is 3000 circuits per satellite. Each satellite weighs 1917 kg (4226 pounds) at launch and the solar arrays provide 3126 Watts of power. Satellites are launched in pairs on Ariane, Atlas, or other vehicles. Each satellite is placed in a circular orbit at an altitude of 10,354 km. There are three orbit planes inclined at 55° to the equatorial plane

  6. Note: Inter-satellite laser range-rate measurement by using digital phase locked loop.

    Science.gov (United States)

    Liang, Yu-Rong; Duan, Hui-Zong; Xiao, Xin-Long; Wei, Bing-Bing; Yeh, Hsien-Chi

    2015-01-01

    This note presents an improved high-resolution frequency measurement system dedicated for the inter-satellite range-rate monitoring that could be used in the future's gravity recovery mission. We set up a simplified common signal test instead of the three frequencies test. The experimental results show that the dominant noises are the sampling time jitter and the thermal drift of electronic components, which can be reduced by using the pilot-tone correction and passive thermal control. The improved noise level is about 10(-8) Hz/Hz(1/2)@0.01Hz, limited by the signal-to-noise ratio of the sampling circuit.

  7. A linearly and circularly polarized active integrated antenna

    Science.gov (United States)

    Khoshniat, Ali

    This thesis work presents a new harmonic suppression technique for microstrip patch antennas. Harmonic suppression in active integrated antennas is known as an effective method to improve the efficiency of amplifiers in transmitter side. In the proposed design, the antenna works as the radiating element and, at the same time, as the tuning load for the amplifier circuit that is directly matched to the antenna. The proposed active antenna architecture is easy to fabricate and is symmetric, so it can be conveniently mass-produced and designed to have circular polarization, which is preferred in many applications such as satellite communications. The antenna simulations were performed using Ansoft High Frequency System Simulator (HFSS) and all amplifier design steps were simulated by Advanced Design System (ADS). The final prototypes of the linearly polarized active integrated antenna and the circularly polarized active integrated antenna were fabricated using a circuit board milling machine. The antenna radiation pattern was measured inside Utah State University's anechoic chamber and the results were satisfactory. Power measurements for the amplifiers' performance were carried out inside the chamber and calculated by using the Friis transmission equation. It is seen that a significant improvement in the efficiency is achieved compared to the reference antenna without harmonic suppression. Based on the success in the single element active antenna design, the thesis also presents a feasibility of applying the active integrated antenna in array configuration, in particular, in scanning array design to yield a low-profile, low-cost alternative to the parabolic antenna transmitter of satellite communication systems.

  8. The planar parabolic optical antenna.

    Science.gov (United States)

    Schoen, David T; Coenen, Toon; García de Abajo, F Javier; Brongersma, Mark L; Polman, Albert

    2013-01-09

    One of the simplest and most common structures used for directing light in macroscale applications is the parabolic reflector. Parabolic reflectors are ubiquitous in many technologies, from satellite dishes to hand-held flashlights. Today, there is a growing interest in the use of ultracompact metallic structures for manipulating light on the wavelength scale. Significant progress has been made in scaling radiowave antennas to the nanoscale for operation in the visible range, but similar scaling of parabolic reflectors employing ray-optics concepts has not yet been accomplished because of the difficulty in fabricating nanoscale three-dimensional surfaces. Here, we demonstrate that plasmon physics can be employed to realize a resonant elliptical cavity functioning as an essentially planar nanometallic structure that serves as a broadband unidirectional parabolic antenna at optical frequencies.

  9. Angle-resolved polarimetry measurements of antenna-mediated fluorescence

    CERN Document Server

    Mohtashami, Abbas; Koenderink, A Femius

    2015-01-01

    Optical phase-array antennas can be used to control not only the angular distribution but also the polarization of fluorescence from quantum emitters. The emission pattern of the resulting system is determined by the properties of the antenna, the properties of the emitters and the strength of the antenna-emitter coupling. Here we show that Fourier polarimetry can be used to characterize these three contributions. To this end, we measured the angle and Stokes-parameter resolved emission of bullseye plasmon antennas as well as spiral antennas excited by an ensemble of emitters. We estimate the antenna-emitter coupling on basis of the degree of polarization, and determine the effect of anisotropy in the intrinsic emitter orientation on polarization of the resulting emission pattern. Our results not only provide new insights in the behavior of bullseye and spiral antennas, but also demonstrate the potential of Fourier polarimetry when characterizing antenna mediated fluorescence.

  10. Statistical modeling of phenological phases in Poland based on coupling satellite derived products and gridded meteorological data

    Science.gov (United States)

    Czernecki, Bartosz; Jabłońska, Katarzyna; Nowosad, Jakub

    2016-04-01

    The aim of the study was to create and evaluate different statistical models for reconstructing and predicting selected phenological phases. This issue is of particular importance in Poland where national-wide phenological monitoring was abandoned in the middle of 1990s and the reactivated network was established in 2006. Authors decided to evaluate possibilities of using a wide-range of statistical modeling techniques to create synthetic archive dataset. Additionally, a robust tool for predicting the most distinguishable phenophases using only free of charge data as predictors was created. Study period covers the years 2007-2014 and contains only quality-controlled dataset of 10 species and 14 phenophases. Phenological data used in this study originates from the manual observations network run by the Institute of Meteorology and Water Management - National Research Institute (IMGW-PIB). Three kind of data sources were used as predictors: (i) satellite derived products, (ii) preprocessed gridded meteorological data, and (iii) spatial properties (longitude, latitude, altitude) of the monitoring site. Moderate-Resolution Imaging Spectroradiometer (MODIS) level-3 vegetation products were used for detecting onset dates of particular phenophases. Following indices were used: Normalized Difference Vegetation Index (NDVI), Enhanced Vegetation Index (EVI), Leaf Area Index (LAI), and Fraction of Photosynthetically Active Radiation (fPAR). Additionally, Interactive Multisensor Snow and Ice Mapping System (IMS) products were chosen to detect occurrence of snow cover. Due to highly noisy data, authors decided to take into account pixel reliability information. Besides satellite derived products (NDVI, EVI, FPAR, LAI, Snow cover), a wide group of observational data and agrometeorological indices derived from the European Climate Assessment & Dataset (ECA&D) were used as a potential predictors: cumulative growing degree days (GDD), cumulative growing precipitation days (GPD

  11. Satellite quenching time-scales in clusters from projected phase space measurements matched to simulated orbits

    Science.gov (United States)

    Oman, Kyle A.; Hudson, Michael J.

    2016-12-01

    We measure the star formation quenching efficiency and time-scale in cluster environments. Our method uses N-body simulations to estimate the probability distribution of possible orbits for a sample of observed Sloan Digital Sky Survey galaxies in and around clusters based on their position and velocity offsets from their host cluster. We study the relationship between their star formation rates and their likely orbital histories via a simple model in which star formation is quenched once a delay time after infall has elapsed. Our orbit library method is designed to isolate the environmental effect on the star formation rate due to a galaxy's present-day host cluster from `pre-processing' in previous group hosts. We find that quenching of satellite galaxies of all stellar masses in our sample (109-10^{11.5}M_{⊙}) by massive (> 10^{13} M_{⊙}) clusters is essentially 100 per cent efficient. Our fits show that all galaxies quench on their first infall, approximately at or within a Gyr of their first pericentric passage. There is little variation in the onset of quenching from galaxy-to-galaxy: the spread in this time is at most ˜2 Gyr at fixed M*. Higher mass satellites quench earlier, with very little dependence on host cluster mass in the range probed by our sample.

  12. The use of mobile satellite communication terminals

    Science.gov (United States)

    Law, P. A.

    The role of small portable terminals in military satellite systems is examined; the discussion embraces terminals with an antenna reflector diameter of seven meters or less. Emphasis is placed on the specification of MARMOSET (Marconi Mobile Satellite Earth Terminal). Also considered are ship-borne satellite terminals, the improved SCOT terminal, interoperability, reduced downlink power, and reliability and availability.

  13. Technology for a quasi-GSO satellite communications system

    OpenAIRE

    Katagi, T.; Yonezawa, R.; Chiba, I.; Urasaki, S.

    1999-01-01

    In this paper, a satellite communications system using a Quasi Geostationary Satellite Orbit (Quasi-GSO) is proposed. A 24-hour period Quasi-GSO system could give high quality communication to high latitude regions with its satellites observed from earth stations having high elevation angles. In this paper, a system concept and a deployable flat antenna with light weight antenna elements are described proposing it to be a good candidate for mobile communications satellite use.

  14. Radiated Power Classification and Polarization Control of Cylindrical Phased Array Antenna%圆柱相控阵天线的功率分级和极化控制

    Institute of Scientific and Technical Information of China (English)

    李海林; 周建江; 谭静; 汪飞

    2013-01-01

    为满足共形相控阵的功率分级和极化捷变的要求,给出了一种新的圆柱阵列天线设计方法.阵列天线的天线单元由两种极化正交的线极化单元构成,且在阵列中交替出现.针对天线单元只能以开启或关闭进行幅度控制,提出了基于天线单元有效辐射功率排序方法的功率分级方案,并采用多目标粒子群算法对副瓣和交叉极化进行了抑制.仿真结果表明,基于双天线单元类型的圆柱阵列天线有效地实现了功率分级,在期望方向上实现了指定极化方向的最大功率辐射,且副瓣和交叉极化低.%For power classification and polarization control of conformal phased array antenna,a new cylindrical array antenna with two types of elements arranged alternately on its surface is designed.Then,a power classification method based on effective sorting of radiated power of elements is proposed when each antenna element is only turning on or off status.Finally,sidelobes and cross-polarization are optimized by multi-objective particle swarm optimization (MOPSO).Results indicate that with low sidelobes and cross-polarization,maximum power radiation in the given radiated direction and polarization direction can be effectively got in this cylindrical phased array antenna.

  15. Design considerations for solar power satellites

    Science.gov (United States)

    Arndt, G. D.; Leopold, L.

    1978-01-01

    This report summarizes the performance characteristics of a conceptual solar power satellite (SPS) system with emphasis on the microwave power transmission system. The latest tradeoff studies on photovoltaic and thermal systems for converting solar energy into electricity at the satellite are reviewed. The microwave system, consisting of dc-RF amplifiers, a 1-km phased array, and a ground antenna/rectifier scheme is capable of delivering 5 GW of power to the commercial grid. The transmission efficiencies of smaller system sizes (down to 1 GW) are compared with that of the nominal 5 GW system. At present the frequency region of interest is the IMS (industrial, medical, and scientific) band at 2450 plus or minus 50 MHz. Economic and technical tradeoffs as a function of the microwave operating frequency are considered. Candidate dc-RF power converter tubes, including medium-power amplitrons, high-power klystrons, and low-power solid state amplifiers, are examined.

  16. Structurally Integrated Antenna Concepts for HALE UAVs

    Science.gov (United States)

    Cravey, Robin L.; Vedeler, Erik; Goins, Larry; Young, W. Robert; Lawrence, Roland W.

    2006-01-01

    This technical memorandum describes work done in support of the Multifunctional Structures and Materials Team under the Vehicle Systems Program's ITAS (Integrated Tailored Aero Structures) Project during FY 2005. The Electromagnetics and Sensors Branch (ESB) developed three ultra lightweight antenna concepts compatible with HALE UAVs (High Altitude Long Endurance Unmanned Aerial Vehicles). ESB also developed antenna elements that minimize the interaction between elements and the vehicle to minimize the impact of wing flexure on the EM (electromagnetic) performance of the integrated array. In addition, computer models were developed to perform phase correction for antenna arrays whose elements are moving relative to each other due to wing deformations expected in HALE vehicle concepts. Development of lightweight, conformal or structurally integrated antenna elements and compensating for the impact of a lightweight, flexible structure on a large antenna array are important steps in the realization of HALE UAVs for microwave applications such as passive remote sensing and communications.

  17. Flexible plasma linear antenna

    Science.gov (United States)

    Zhao, Jiansen; Wang, Shengzheng; Wu, Huafeng; Liu, Yue; Chang, Yongmeng; Chen, Xinqiang

    2017-02-01

    In this work, we introduce a type of plasma antenna that was fabricated using flexible materials and excited using a 5-20 kHz alternating current (ac) power supply. The results showed that the antenna characteristics, including the impedance, the reflection coefficient (S11), the radiation pattern, and the gain, can be controlled rapidly and easily by varying both the discharge parameters and the antenna shapes. The scope for reconfiguration is greatly enhanced when the antenna shape is changed from a monopole to a helix configuration. Additionally, the antenna polarization can also be adjusted by varying the antenna shapes.

  18. Trellis coding with Continuous Phase Modulation (CPM) for satellite-based land-mobile communications

    Science.gov (United States)

    1989-01-01

    This volume of the final report summarizes the results of our studies on the satellite-based mobile communications project. It includes: a detailed analysis, design, and simulations of trellis coded, full/partial response CPM signals with/without interleaving over various Rician fading channels; analysis and simulation of computational cutoff rates for coherent, noncoherent, and differential detection of CPM signals; optimization of the complete transmission system; analysis and simulation of power spectrum of the CPM signals; design and development of a class of Doppler frequency shift estimators; design and development of a symbol timing recovery circuit; and breadboard implementation of the transmission system. Studies prove the suitability of the CPM system for mobile communications.

  19. Breadboard Signal Processor for Arraying DSN Antennas

    Science.gov (United States)

    Jongeling, Andre; Sigman, Elliott; Chandra, Kumar; Trinh, Joseph; Soriano, Melissa; Navarro, Robert; Rogstad, Stephen; Goodhart, Charles; Proctor, Robert; Jourdan, Michael; hide

    2008-01-01

    A recently developed breadboard version of an advanced signal processor for arraying many antennas in NASA s Deep Space Network (DSN) can accept inputs in a 500-MHz-wide frequency band from six antennas. The next breadboard version is expected to accept inputs from 16 antennas, and a following developed version is expected to be designed according to an architecture that will be scalable to accept inputs from as many as 400 antennas. These and similar signal processors could also be used for combining multiple wide-band signals in non-DSN applications, including very-long-baseline interferometry and telecommunications. This signal processor performs functions of a wide-band FX correlator and a beam-forming signal combiner. [The term "FX" signifies that the digital samples of two given signals are fast Fourier transformed (F), then the fast Fourier transforms of the two signals are multiplied (X) prior to accumulation.] In this processor, the signals from the various antennas are broken up into channels in the frequency domain (see figure). In each frequency channel, the data from each antenna are correlated against the data from each other antenna; this is done for all antenna baselines (that is, for all antenna pairs). The results of the correlations are used to obtain calibration data to align the antenna signals in both phase and delay. Data from the various antenna frequency channels are also combined and calibration corrections are applied. The frequency-domain data thus combined are then synthesized back to the time domain for passing on to a telemetry receiver

  20. Analysis of a New Design Structure For Reflectarray Antennas

    Directory of Open Access Journals (Sweden)

    W. Moulessehoul, S.M. Meriah

    2013-12-01

    Full Text Available The key factor in the designing of reflectarray antennas is the determination of the phase range of each element constituting the antenna array, this parameters is improved by introducing slots in the radiating element, and by adjusted their dimensions. A novel structure of radiating antenna is developed whose geometry is Bowtie. The reflection coefficient phase is obtained by the unit cell waveguide approach under the CST Microwave Studio.

  1. Exploitation of amplitude and phase of satellite SAR images for landslide mapping: the case of Montescaglioso (South Italy)

    Science.gov (United States)

    Raspini, Federico; Ciampalini, Andrea; Lombardi, Luca; Nocentini, Massimiliano; Gigli, Giovanni; Casagli, Nicola; Del Conte, Sara; Ferretti, Alessandro

    2016-04-01

    Pre- event and event landslide deformations have been detected and measured for the landslide that occurred on 3 December 2013 on the south-western slope of the Montescaglioso village (Basilicata Region, southern Italy). The event, triggered by prolonged rainfalls, created significant damage to buildings and local infrastructures. Ground displacements have been mapped through an integrated analysis based on a series of high resolution SAR (Synthetic Aperture Radar) images acquired by the Italian constellation of satellites COSMO-SkyMed. Analysis has been performed by exploiting both phase (through multi-image SAR interferometry) and amplitude information (through speckle tracking techniques) of the satellite images. SAR Interferometry, applied to images taken before the event, revealed a general pre-event movement, in the order of a few mm/yr, in the south-western slope of the Montescaglioso village. Highest pre-event velocities, ranging between 8 and 12 mm/yr, have been recorded in the sector of the slope where the first movement of the landslide took place. Speckle tracking, applied to images acquired before and after the event, allowed the retrieval of the 3D deformation field produced by the landslide. It also showed that ground displacements produced by the landslide have a dominant SSW component, with values exceeding 10 m for large sectors of the landslide area, with local peaks of 20 m in its central and deposit areas. Two minor landslides with a dominant SSE direction, which were detected in the upper parts of the slope, likely also occurred as secondary phenomena as consequence of the SSW movement of the main Montescaglioso landslide. This work demonstrates that this complementary approach, based on the synergistic exploitation of phase and amplitude SAR data, can become a powerful tool for landslide investigation, allowing the detection of slow, precursory deformation patterns as well the retrieval of full 3D surface displacement fields caused by large

  2. Antenna Pattern Range (APR)

    Data.gov (United States)

    Federal Laboratory Consortium — TheAntenna Pattern Range (APR)features a non-metallic arch with a trolley to move the transmit antenna from the horizon to zenith. At the center of the ground plane,...

  3. Antenna Structure Registrate

    Data.gov (United States)

    Department of Homeland Security — This file is an extract of the Antenna Structure Registrate (ASR). The ASR consists of antenna structures that are more than 60.96 meters (200 feet) in height or...

  4. Field Deployment of Prototype Antenna Tiles for the Mileura Widefield Array--Low Frequency Demonstrator

    CERN Document Server

    Bowman, J D; Briggs, F H; Corey, B E; Lynch, M J; Bhat, N D R; Cappallo, R J; Doeleman, S S; Fanous, B J; Herne, D; Hewitt, J N; Johnston, C; Kasper, J C; Kocz, J; Kratzenberg, E; Lonsdale, C J; Morales, M F; Oberoi, D; Salah, J E; Stansby, B; Stevens, J; Torr, G; Wayth, R; Webster, R L; Wyithe, J S B; Bowman, Judd D.; Barnes, David G.; Briggs, Frank H.; Corey, Brian E.; Lynch, Merv J.; Cappallo, Roger J.; Doeleman, Sheperd S.; Fanous, Brian J.; Herne, David; Hewitt, Jacqueline N.; Johnston, Chris; Kasper, Justin C.; Kocz, Jonathon; Kratzenberg, Eric; Lonsdale, Colin J.; Morales, Miguel F.; Oberoi, Divya; Salah, Joseph E.; Stansby, Bruce; Stevens, Jamie; Torr, Glen; Wayth, Randall; Webster, Rachel L.

    2006-01-01

    Experiments were performed with prototype antenna tiles for the Mileura Widefield Array--Low Frequency Demonstrator (MWA-LFD) to better understand the widefield, wideband properties of their design and to characterize the radio frequency interference (RFI) between 80 and 300 MHz at the site in Western Australia. Observations acquired during the six month deployment confirmed the predicted sensitivity of the antennas, sky-noise dominated system temperatures, and phase-coherent interferometric measurements. The radio spectrum is remarkably free of strong terrestrial signals, with the exception of two narrow frequency bands allocated to satellite downlinks and rare bursts due to ground-based transmissions being scattered from aircraft and meteor trails. Results indicate the potential of the MWA-LFD to make significant achievements in its three key science objectives: epoch of reionziation science, heliospheric science, and radio transient detection.

  5. Cross resonant optical antenna.

    Science.gov (United States)

    Biagioni, P; Huang, J S; Duò, L; Finazzi, M; Hecht, B

    2009-06-26

    We propose a novel cross resonant optical antenna consisting of two perpendicular nanosized gold dipole antennas with a common feed gap. We demonstrate that the cross antenna is able to convert propagating fields of any polarization state into correspondingly polarized, localized, and enhanced fields and vice versa. The cross antenna structure therefore opens the road towards the control of light-matter interactions based on polarized light as well as the analysis of polarized fields on the nanometer scale.

  6. Cross Resonant Optical Antenna

    Science.gov (United States)

    Biagioni, P.; Huang, J. S.; Duò, L.; Finazzi, M.; Hecht, B.

    2009-06-01

    We propose a novel cross resonant optical antenna consisting of two perpendicular nanosized gold dipole antennas with a common feed gap. We demonstrate that the cross antenna is able to convert propagating fields of any polarization state into correspondingly polarized, localized, and enhanced fields and vice versa. The cross antenna structure therefore opens the road towards the control of light-matter interactions based on polarized light as well as the analysis of polarized fields on the nanometer scale.

  7. 机载毫米波有源相控阵天线热设计研究%Research of Thermal Design on an Airborne Millimeter-Wave Active Phased Array Antenna

    Institute of Scientific and Technical Information of China (English)

    何林涛

    2016-01-01

    In order to solve the problem of thermal design on an airborne millimeter-wave active phased array antenna,this paper studied the method which combined engineering demand with thermal design software.The process of thermal design on antenna which was based on the proposed method was described.According to conclusions of the process,optimization of coolant passage layout solved the problem of thermal design on antenna efficiently.At last,the experimental result showed that the method is feasible.%针对机载毫米波有源相控阵天线的热设计问题,研究了一种工程需求和专业热仿真软件结合的方法。分析了采用该设计方法的天线热设计流程,分析结果表明,优化流道布局可以有效地解决天线这类电子设备的热设计问题。并经过实物试验的验证,证实了该方法的可行性。

  8. Calculations and Analysis of the Triangle-grid Taylor and Bayliss Circular-aperture Phased Array Antenna%三角形栅格圆口径平面相控阵天线的分析计算

    Institute of Scientific and Technical Information of China (English)

    袁汉钦; 陈玺羽

    2014-01-01

    以矩形栅格和三角形栅格的圆口径天线的方向图进行了计算研究,首先给出了三角形栅格圆口径平面阵的模型,依据模型计算出在使用三角形栅格时能有效减少阵元数量;首次计算了圆口径三角形栅格的泰勒加权和方向图和贝利斯加权差方向图,为工程应用提供了依据。%This paper researches on the pattern of the circular-aperture phased array antenna for the rec-tangle and triangle grid. Firstly,the model for triangle-grid circular-aperture is given. According to the model,the calculating results show that the elements of the array antenna are saved by applying the trian-gle-grid in circular-apetures antenna. The paper primarily studies the pattern of the triangle-grid Taylor and Bayliss circular-aperture,which can be the reference for the practical application.

  9. Reusable Reentry Satellite (RRS) system design study. Phase B, appendix E: Attitude control system study

    Science.gov (United States)

    1991-01-01

    A study which consisted of a series of design analyses for an Attitude Control System (ACS) to be incorporated into the Re-usable Re-entry Satellite (RRS) was performed. The main thrust of the study was associated with defining the control laws and estimating the mass and power requirements of the ACS needed to meet the specified performance goals. The analyses concentrated on the different on-orbit control modes which start immediately after the separation of the RRS from the launch vehicle. The three distinct on-orbit modes considered for these analyses are as follows: (1) Mode 1 - A Gravity Gradient (GG) three-axis stabilized spacecraft with active magnetic control; (2) Mode 2 - A GG stabilized mode with a controlled yaw rotation rate ('rotisserie') using three-axis magnetic control and also incorporating a 10 N-m-s momentum wheel along the (Z) yaw axis; and (3) Mode 3 - A spin stabilized mode of operation with the spin about the pitch (Y) axis, incorporating a 20 N-m-s momentum wheel along the pitch (Y) axis and attitude control via thrusters. To investigate the capabilities of the different controllers in these various operational modes, a series of computer simulations and trade-off analyses have been made to evaluate the achievable performance levels, and the necessary mass and power requirements.

  10. Satellite quenching timescales in clusters from projected phase space measurements matched to simulated orbits

    CERN Document Server

    Oman, Kyle A

    2016-01-01

    We measure the star formation quenching efficiency and timescale in cluster environments. Our method uses N-body simulations to estimate the probability distribution of possible orbits for a sample of observed SDSS galaxies in and around clusters based on their position and velocity offsets from their host cluster. We study the relationship between their star formation rates and their likely orbital histories via a simple model in which star formation is quenched once a delay time after infall has elapsed. Our orbit library method is designed to isolate the environmental effect on the star formation rate due to a galaxy's present-day host cluster from `pre-processing' in previous group hosts. We find that quenching of satellite galaxies of all stellar masses in our sample ($10^{9}-10^{11.5}\\,{\\rm M}_\\odot$) by massive ($> 10^{13}\\,{\\rm M}_\\odot$) clusters is essentially $100$ per cent efficient. Our fits show that all galaxies quench on their first infall, approximately at or within a Gyr of their first peric...

  11. Design of Multilevel Sequential Rotation Feeding Networks Used for Circularly Polarized Microstrip Antenna Arrays

    Directory of Open Access Journals (Sweden)

    Aixin Chen

    2012-01-01

    Full Text Available Sequential rotation feeding networks can significantly improve performance of the circularly polarized microstrip antenna array. In this paper, single, double, and multiple series-parallel sequential rotation feeding networks are examined. Compared with conventional parallel feeding structures, these multilevel feeding techniques present reduction of loss, increase of bandwidth, and improvement of radiation pattern and polarization purity. By using corner-truncated square patch as the array element and adopting appropriate level of sequential rotation series-parallel feeding structures as feeding networks, microstrip arrays can generate excellent circular polarization (CP over a relatively wide frequency band. They can find wide applications in phased array radar and satellite communication systems.

  12. HF Radio Astronomy from a Small Satellite

    Science.gov (United States)

    2016-06-15

    antenna as shown in Figure 4. Dual mode loop-dipole elements are described in [25,29,30]. The 10 MHz radiation patterns of the six modes are shown in... telemetry , GPS, and vector antenna modules. Robey 14 30th Annual AIAA/USU Conference on Small Satellites Alexander Morris. Thanks to Sara Klein for

  13. FORTE antenna element and release mechanism design

    Energy Technology Data Exchange (ETDEWEB)

    Rohweller, D.J. [Astro Aerospace Corp., Carpinteria, CA (United States); Butler, T.Af. [Los Alamos National Lab., NM (United States)

    1995-02-01

    The Fast On-Orbit Recording of Transient Events (FORTE) satellite being built by Los Alamos National Laboratory (LANL) and Sandia National Laboratories (SNL) has as its most prominent feature a large deployable (11 m by 5 m) log periodic antenna to monitor emissions from electrical storms on the Earth. This paper describes the antenna and the design for the long elements and explains the dynamics of their deployment and the damping system employed. It also describes the unique paraffin-actuated reusable tie-down and release mechanism employed in the system.

  14. Coherently combining antennas

    Science.gov (United States)

    Dybdal, Robert B. (Inventor); Curry, Samuel J. (Inventor)

    2009-01-01

    An apparatus includes antenna elements configured to receive a signal including pseudo-random code, and electronics configured to use the pseudo-random code to determine time delays of signals incident upon the antenna elements and to compensate the signals to coherently combine the antenna elements.

  15. Vertically Polarized Omnidirectional Printed Slot Loop Antenna

    DEFF Research Database (Denmark)

    Kammersgaard, Nikolaj Peter Iversen; Kvist, Søren H.; Thaysen, Jesper

    2015-01-01

    A novel vertically polarized omnidirectional printed slot loop antenna has been designed, simulated, fabricated and measured. The slot loop works as a magnetic loop. The loop is loaded with inductors to insure uniform and in-phase fields in the slot in order to obtain an omnidirectional radiation...... pattern. The antenna is designed for the 2.45 GHz Industrial, Scientific and Medical band. Applications of the antenna are many. One is for on-body applications since it is ideal for launching a creeping waves due to the polarization....

  16. Autonomous Satellite Command and Control through the World Wide Web: Phase 3

    Science.gov (United States)

    Cantwell, Brian; Twiggs, Robert

    1998-01-01

    NASA's New Millenium Program (NMP) has identified a variety of revolutionary technologies that will support orders of magnitude improvements in the capabilities of spacecraft missions. This program's Autonomy team has focused on science and engineering automation technologies. In doing so, it has established a clear development roadmap specifying the experiments and demonstrations required to mature these technologies. The primary developmental thrusts of this roadmap are in the areas of remote agents, PI/operator interface, planning/scheduling fault management, and smart execution architectures. Phases 1 and 2 of the ASSET Project (previously known as the WebSat project) have focused on establishing World Wide Web-based commanding and telemetry services as an advanced means of interfacing a spacecraft system with the PI and operators. Current automated capabilities include Web-based command submission, limited contact scheduling, command list generation and transfer to the ground station, spacecraft support for demonstrations experiments, data transfer from the ground station back to the ASSET system, data archiving, and Web-based telemetry distribution. Phase 2 was finished in December 1996. During January-December 1997 work was commenced on Phase 3 of the ASSET Project. Phase 3 is the subject of this report. This phase permitted SSDL and its project partners to expand the ASSET system in a variety of ways. These added capabilities included the advancement of ground station capabilities, the adaptation of spacecraft on-board software, and the expansion of capabilities of the ASSET management algorithms. Specific goals of Phase 3 were: (1) Extend Web-based goal-level commanding for both the payload PI and the spacecraft engineer; (2) Support prioritized handling of multiple PIs as well as associated payload experimenters; (3) Expand the number and types of experiments supported by the ASSET system and its associated spacecraft; (4) Implement more advanced resource

  17. Using Antenna Arrays to Motivate the Study of Sinusoids

    Science.gov (United States)

    Becker, J. P.

    2010-01-01

    Educational activities involving antenna arrays to motivate the study of sinusoids are described. Specifically, using fundamental concepts related to phase and simple geometric arguments, students are asked to predict the location of interference nulls in the radiation pattern of two-element phased array antennas. The location of the radiation…

  18. Using Antenna Arrays to Motivate the Study of Sinusoids

    Science.gov (United States)

    Becker, J. P.

    2010-01-01

    Educational activities involving antenna arrays to motivate the study of sinusoids are described. Specifically, using fundamental concepts related to phase and simple geometric arguments, students are asked to predict the location of interference nulls in the radiation pattern of two-element phased array antennas. The location of the radiation…

  19. Plan of advanced satellite communication experiments using ETS-6

    Science.gov (United States)

    Ikegami, Tetsushi

    1989-01-01

    In 1992, an Engineering Test Satellite 6 is scheduled to be launched by an H-2 rocket. The missions of ETS-6 are to establish basic technologies of inter-satellite communications using S-band, millimeter waves and optical beams and of fixed and mobile satellite communications using multibeam antenna on board the satellite. A plan of the experiments is introduced.

  20. 毫米波多功能有源相控阵天线设计与实现%Design and Implementation of A MMW Multi-Function Active Phased Array Antenna

    Institute of Scientific and Technical Information of China (English)

    杨亚兵; 程杰; 李绪平; 姜世波

    2014-01-01

    In order to satisfy the technical requirements of some radar and enhance its operational effectiveness, a design and implementation scheme of millimeter-wave ( MMW) multi-function active phased array antenna based on single ridge waveguide slotted array is proposed. Design principle and system structure of the active phased array antenna are presented, key technique are analyzed in detail. Based on theoretical analysis and simulation design, an engineering prototype is developed and tested successfully. Experimental results demonstrate that the MMW multi-function active phased array antenna exhibits excellent characteristics and can meet system technical re-quirements.%为了满足某型雷达的性能要求,显著提高其作战效能,提出了一种基于单脊波导宽边缝隙阵的毫米波多功能有源相控阵天线系统设计与实现方案。阐述了该相控阵天线系统的设计原理和组成架构,并对涉及的关键技术进行了详细分析。在理论分析与仿真设计的基础上,研制了该相控阵天线工程样机并对其进行了相关实验验证。实测结果表明,该毫米波多功能有源相控阵天线系统性能优良可靠,可满足总体技术指标要求。