WorldWideScience

Sample records for sap flow method

  1. [Application of three heat pulse technique-based methods to determine the stem sap flow].

    Science.gov (United States)

    Wang, Sheng; Fan, Jun

    2015-08-01

    It is of critical importance to acquire tree transpiration characters through sap flow methodology to understand tree water physiology, forest ecology and ecosystem water exchange. Tri-probe heat pulse sensors, which are widely utilized in soil thermal parameters and soil evaporation measurement, were applied to implement Salix matsudana sap flow density (Vs) measurements via heat-ratio method (HRM), T-Max method (T-Max) and single-probe heat pulse probe (SHPP) method, and comparative analysis was conducted with additional Grainer's thermal diffusion probes (TDP) measured results. The results showed that, it took about five weeks to reach a stable measurement stage after TPHP installation, Vs measured with three methods in the early stage after installation was 135%-220% higher than Vs in the stable measurement stage, and Vs estimated via HRM, T-Max and SHPP methods were significantly linearly correlated with Vs estimated via TDP method, with R2 of 0.93, 0.73 and 0.91, respectively, and R2 for Vs measured by SHPP and HRM reached 0.94. HRM had relatively higher precision in measuring low rates and reverse sap flow. SHPP method seemed to be very promising to measure sap flow for configuration simplicity and high measuring accuracy, whereas it couldn' t distinguish directions of flow. T-Max method had relatively higher error in sap flow measurement, and it couldn' t measure sap flow below 5 cm3 · cm(-2) · h(-1), thus this method could not be used alone, however it could measure thermal diffusivity for calculating sap flow when other methods were imposed. It was recommended to choose a proper method or a combination of several methods to measure stem sap flow, based on specific research purpose.

  2. Use of the heat dissipation method for sap flow measurement in citrus nursery trees1

    Directory of Open Access Journals (Sweden)

    Eduardo Augusto Girardi

    2010-12-01

    Full Text Available Sap flow could be used as physiological parameter to assist irrigation of screen house citrus nursery trees by continuous water consumption estimation. Herein we report a first set of results indicating the potential use of the heat dissipation method for sap flow measurement in containerized citrus nursery trees. 'Valencia' sweet orange [Citrus sinensis (L. Osbeck] budded on 'Rangpur' lime (Citrus limonia Osbeck was evaluated for 30 days during summer. Heat dissipation probes and thermocouple sensors were constructed with low-cost and easily available materials in order to improve accessibility of the method. Sap flow showed high correlation to air temperature inside the screen house. However, errors due to natural thermal gradient and plant tissue injuries affected measurement precision. Transpiration estimated by sap flow measurement was four times higher than gravimetric measurement. Improved micro-probes, adequate method calibration, and non-toxic insulating materials should be further investigated.

  3. Evaluation of the heat pulse velocity method for measuring sap flow in Pinus patula

    CSIR Research Space (South Africa)

    Dye, PJ

    1996-07-01

    Full Text Available , and has been shown to measure sap flows accurately in a variety of hardwood trees. This method has not been sufficiently verified for pine trees where the presence of a strongly-defined ring structure in the sapwood gives rise to a complex radial pattern...

  4. Wireless sap flow measurement system

    Science.gov (United States)

    Kuo, C.; Davis, T. W.; Tseng, C.; Cheng, C.; Liang, X.; Yu, P.

    2010-12-01

    This study exhibits a measurement system for wireless sensor networks to measure sap flow in multiple locations simultaneously. Transpiration is a major component of the land-surface system because it is indicative of the water movement between the soil and the air. Sap flow can be used to approximate transpiration. In forests, transpiration cannot be represented by the sap flow from a single tree. Multi-location sap flow measurements are required to show the heterogeneity caused by different trees or soil conditions. Traditional multi-location measurements require manpower and capital for data collection and instrument maintenance. Fortunately, multi-location measurements can be achieved by using the new technology of wireless sensor networks. With multi-hop communication protocol, data can be forwarded to the base station via multiple sensor nodes. This communication protocol can provide reliable data collection with the least power consumption. This study encountered two major problems. The first problem was signal amplification. The Crossbow IRIS mote was selected as the sensor node that receives the temperature data of the sap flow probe (thermocouple) through a MDA300 data acquisition board. However, the wireless sensor node could not directly receive any data from the thermocouples since the least significant bit value of the MDA300, 0.6 mV, is much higher than the voltage signal generated. Thus, the signal from the thermocouple must be amplified to exceed this threshold. The second problem is power management. A specific heat differential is required for the thermal dissipation method of measuring sap flow. Thus, an adjustable DC power supply is necessary for calibrating the heater's temperature settings. A circuit was designed to combine the signal amplifier and power regulator. The regulator has been designed to also provide power to the IRIS mote to extend battery life. This design enables wireless sap flow measurements in the forest. With the

  5. Evaluation of the sap flow using heat pulse method to determine transpiration of the Populus euphratica canopy

    Institute of Scientific and Technical Information of China (English)

    ZHANG Xiaoyou; KANG Ersi; ZHOU Maoxian

    2007-01-01

    The sap flow of the sampled Populus euphratica stems at different radial depths and directions had been studied in Ejina Oasis,in the lower reaches of the Heihe River.Based on sap flow measurements,the transpiration of the entire canopy was calculated.Results showed a linear correlation between the sap flow and the sapwood area of the P.euphratica.Through the analysis of the diameter at breast height in the sample plot,it was found that the distribution of the diameters and the corresponding sapwood area was exponentially correlated,with the coefficient of correlation being 0.976,7.The calculated transpiration of the Populus euphratica canopy was 214.9 mm based on the specific conductivity method.

  6. Evapotranspiration in a cottonwood (Populus fremontii) restoration plantation estimated by sap flow and remote sensing methods

    Science.gov (United States)

    Nagler, P.; Jetton, A.; Fleming, J.; Didan, K.; Glenn, E.; Erker, J.; Morino, K.; Milliken, J.; Gloss, S.

    2007-01-01

    Native tree plantations have been proposed for the restoration of wildlife habitat in human-altered riparian corridors of western U.S. rivers. Evapotranspiration (ET) by riparian vegetation is an important, but poorly quantified, term in river water budgets. Native tree restoration plots will potentially increase ET. We used sap flow sensors and satellite imagery to estimate ET in a 8 ha, cottonwood (Populus fremontii) restoration plot on the Lower Colorado River. Biometric methods were used to scale leaf area to whole trees and stands of trees. This technique was used to validate our estimates of ET obtained by scaling from branch level to stand (or plot) level measurements of ET. Cottonwood trees used 6-10 mm day-1 of water during the peak of the growing season as determined by sap flow sensors, and annual rates scaled by time-series MODIS satellite imagery were approximately 1.2 m year-1. Although irrigation was not quantified, the field had been flood irrigated at 2 week intervals during the 3 years prior to the study, receiving approximately 2 m year-1 of water. A frequency-domain electromagnetic induction survey of soil moisture content showed that the field was saturated (26-28% gravimetric water content) at the 90-150 cm soil depth under the field. Trees were apparently rooted into the saturated soil, and considerable saving of water could potentially be achieved by modifying the irrigation regime to take into account that cottonwoods are phreatophytes. The study showed that cottonwood ET can be monitored by remote sensing methods calibrated with ground measurements with an accuracy or uncertainty of 20-30% in western riparian corridors. ?? 2007 Elsevier B.V. All rights reserved.

  7. (BOREAS) BOREAS TE-7 Sap Flow Data

    Science.gov (United States)

    Hall, Forrest G. (Editor); Papagno, Andrea (Editor); Hogg, E. H.; Hurdle, P. A.

    2000-01-01

    The BOREAS TE-7 team collected data sets in support of its efforts to characterize and interpret information on the sap flow of boreal vegetation. The heat pulse method was used to monitor sap flow and to estimate rates of transpiration from aspen, black spruce, and mixed wood forests at the SSAOA, MIX, SSA-OBS. and Batoche sites in Saskatchewan, Canada. Measurements were made at the various sites from May to October 1994, May to October 1995, and April to October 1996. A scaling procedure was used to estimate canopy transpiration rates from the sap flow measurements. The data were stored in tabular ASCII files. Analyses to date show a tendency for sap flow in aspen to remain remarkably constant over a wide range of environmental conditions VPD from 1.0 to 4.8 kPa and solar radiation less than 400 W/sq m). For forests with high aerodynamic conductance, the results would indicate an inverse relationship between stomatal conductance and VPD, for VPD greater than 1 kPa. A possible interpretation is that stomata are operating to maintain leaf water potentials above a critical minimum value, which in turn places a maximum value on the rate of sap flow that can be sustained by the tree. The data files are available on a CD-ROM (see document number 20010000884), or from the Oak Ridge National Laboratory (ORNL) Distrobuted Activity Archive Center (DAAC).

  8. A comparison of methods for determining field evapotranspiration: photosynthesis system, sap flow, and eddy covariance

    Science.gov (United States)

    Zhang, Z.; Tian, F.; Hu, H.; Yang, P.

    2014-03-01

    A multi-scale, multi-technique study was conducted to measure evapotranspiration and its components in a cotton field under mulched drip irrigation conditions in northwestern China. Three measurement techniques at different scales were used: a photosynthesis system (leaf scale), sap flow (plant scale), and eddy covariance (field scale). The experiment was conducted from July to September 2012. To upscale the evapotranspiration from the leaf to plant scale, an approach that incorporated the canopy structure and the relationships between sunlit and shaded leaves was proposed. To upscale the evapotranspiration from the plant to field scale, an approach based on the transpiration per unit leaf area was adopted and modified to incorporate the temporal variability in the relationship between leaf areas and stem diameter. At the plant scale, the estimate of the transpiration based on the photosynthesis system with upscaling was slightly higher (18%) than that obtained by sap flow. At the field scale, the estimates of transpiration derived from sap flow with upscaling and eddy covariance showed reasonable consistency during the cotton's open-boll growth stage, during which soil evaporation can be neglected. The results indicate that the proposed upscaling approaches are reasonable and valid. Based on the measurements and upscaling approaches, evapotranspiration components were analyzed for a cotton field under mulched drip irrigation. During the two analyzed sub-periods in July and August, evapotranspiration rates were 3.94 and 4.53 m day-1, respectively. The fraction of transpiration to evapotranspiration reached 87.1% before drip irrigation and 82.3% after irrigation. The high fraction of transpiration over evapotranspiration was principally due to the mulched film above the drip pipe, low soil water content in the inter-film zone, well-closed canopy, and high water requirement of the crop.

  9. Stem sap flow in plants under low gravity conditions

    Science.gov (United States)

    Tokuda, Ayako; Hirai, Hiroaki; Kitaya, Yoshiaki

    2016-07-01

    A study was conducted to obtain a fundamental knowledge for plant functions in bio-regenerative life support systems in space. Stem sap flow in plants is important indicators for water transport from roots to atmosphere through leaves. In this study, stem sap flow in sweetpotato was assessed at gravity levels from 0.01 to 2 g for about 20 seconds each during parabolic airplane flights. Stem sap flow was monitored with a heat balance method in which heat generated with a tiny heater installed in the stem was transferred upstream and downstream by conduction and upstream by convection with the sap flow through xylems of the vascular tissue. Thermal images of stem surfaces near heated points were captured using infrared thermography and the internal heat convection corresponding to the sap flow was analyzed. In results, the sap flow in stems was suppressed more at lower gravity levels without forced air circulation. No suppression of the stem sap flow was observed with forced air circulation. Suppressed sap flow in stems would be caused by suppression of transpiration in leaves and would cause restriction of water and nutrient uptake in roots. The forced air movement is essential to culture healthy plants at a high growth rate under low gravity conditions in space.

  10. Sap flow sensors: construction, quality control and comparison.

    Science.gov (United States)

    Davis, Tyler W; Kuo, Chen-Min; Liang, Xu; Yu, Pao-Shan

    2012-01-01

    This work provides a design for two types of sensors, based on the thermal dissipation and heat ratio methods of sap flow calculation, for moderate to large scale deployments for the purpose of monitoring tree transpiration. These designs include a procedure for making these sensors, a quality control method for the final products, and a complete list of components with vendors and pricing information. Both sensor designs were field tested alongside a commercial sap flow sensor to assess their performance and show the importance for quality controlling the sensor outputs. Results show that for roughly 2% of the cost of commercial sensors, self-made sap flow sensors can provide acceptable estimates of the sap flow measurements compared to the commercial sensors.

  11. Sap flow index as an indicator of water storage use

    Directory of Open Access Journals (Sweden)

    Nadezhdina Nadezhda

    2015-06-01

    Full Text Available Symmetrical temperature difference also known as the sap flow index (SFI forms the basis of the Heat Field Deformation sap flow measurement and is simultaneously collected whilst measuring the sap flow. SFI can also be measured by any sap flow method applying internal continuous heating through the additional installation of an axial differential thermocouple equidistantly around a heater. In earlier research on apple trees SFI was found to be an informative parameter for tree physiological studies, namely for assessing the contribution of stem water storage to daily transpiration. The studies presented in this work are based on the comparative monitoring of SFI and diameter in stems of different species (Pseudotsuga menziesii, Picea omorika, Pinus sylvestris and tree sizes. The ability of SFI to follow the patterns of daily stem water storage use was empirically confirmed by our data. Additionally, as the HFD multipointsensors can measure sap flow at several stem sapwood depths, their use allowed to analyze the use of stored water in different xylem layers through SFI records. Radial and circumferential monitoring of SFI on large cork oak trees provided insight into the relative magnitude and timing of the contribution of water stored in different sapwood layers or stem sectors to transpiration.

  12. Sap flow measurements of lateral tree roots in agroforestry systems.

    Science.gov (United States)

    Lott, J. E.; Khan, A. A. H.; Ong, C. K.; Black, C. R.

    1996-01-01

    Successful extension of agroforestry to areas of the semi-arid tropics where deep reserves of water exist requires that the tree species be complementary to the associated crops in their use of water within the crop rooting zone. However, it is difficult to identify trees suitable for dryland agroforestry because most existing techniques for determining water uptake by roots cannot distinguish between absorption by tree and crop roots. We describe a method for measuring sap flow through lateral roots using constant temperature heat balance gauges, and the application of this method in a study of complementarity of water use in agroforestry systems containing Grevillea robusta A. Cunn. Sap flow gauges were attached to the trunks and roots of Grevillea with minimum disturbance to the soil. Thermal energy emanating from the soil adversely affected the accuracy of sap flow gauges attached to the roots, with the result that the uncorrected values were up to eightfold greater than the true water uptake determined gravimetrically. This overestimation was eliminated by using a calibration method in which nonconducting excised root segments, with sap flow gauges attached, were placed adjacent to the live roots. The power consumption and temperature differentials of the excised roots were used to correct for external sources and internal losses of heat within the paired live root. The fraction of the total sap flow through individual trees supplied by the lateral roots varied greatly between trees of similar canopy size. Excision of all lateral roots, except for one to which a heat balance gauge was attached, did not significantly increase sap flow through the intact root, suggesting that it was functioning at near maximum capacity.

  13. SAPFLUXNET: towards a global database of sap flow measurements.

    Science.gov (United States)

    Poyatos, Rafael; Granda, Víctor; Molowny-Horas, Roberto; Mencuccini, Maurizio; Steppe, Kathy; Martínez-Vilalta, Jordi

    2016-12-01

    Plant transpiration is the main evaporative flux from terrestrial ecosystems; it controls land surface energy balance, determines catchment hydrological responses and influences regional and global climate. Transpiration regulation by plants is a key (and still not completely understood) process that underlies vegetation drought responses and land evaporative fluxes under global change scenarios. Thermometric methods of sap flow measurement have now been widely used to quantify whole-plant and stand transpiration in forests, shrublands and orchards around the world. A large body of research has applied sap flow methods to analyse seasonal and diurnal patterns of transpiration and to quantify their responses to hydroclimatic variability, but syntheses of sap flow data at regional to global scales are extremely rare. Here we present the SAPFLUXNET initiative, aimed at building the first global database of plant-level sap flow measurements. A preliminary metadata survey launched in December 2015 showed an encouraging response by the sap flow community, with sap flow data sets from field studies representing >160 species and >120 globally distributed sites. The main goal of SAPFLUXNET is to analyse the ecological factors driving plant- and stand-level transpiration. SAPFLUXNET will open promising research avenues at an unprecedented global scope, namely: (i) exploring the spatio-temporal variability of plant transpiration and its relationship with plant and stand attributes, (ii) summarizing physiological regulation of transpiration by means of few water-use traits, usable for land surface models, (iii) improving our understanding of the coordination between gas exchange and plant-level traits (e.g., hydraulics) and (iv) analysing the ecological factors controlling stand transpiration and evapotranspiration partitioning. Finally, SAPFLUXNET can provide a benchmark to test models of physiological controls of transpiration, contributing to improve the accuracy of

  14. Sapflow+: a four-needle heat-pulse sap flow sensor enabling nonempirical sap flux density and water content measurements.

    Science.gov (United States)

    Vandegehuchte, Maurits W; Steppe, Kathy

    2012-10-01

    • To our knowledge, to date, no nonempirical method exists to measure reverse, low or high sap flux density. Moreover, existing sap flow methods require destructive wood core measurements to determine sapwood water content, necessary to convert heat velocity to sap flux density, not only damaging the tree, but also neglecting seasonal variability in sapwood water content. • Here, we present a nonempirical heat-pulse-based method and coupled sensor which measure temperature changes around a linear heater in both axial and tangential directions after application of a heat pulse. By fitting the correct heat conduction-convection equation to the measured temperature profiles, the heat velocity and water content of the sapwood can be determined. • An identifiability analysis and validation tests on artificial and real stem segments of European beech (Fagus sylvatica L.) confirm the applicability of the method, leading to accurate determinations of heat velocity, water content and hence sap flux density. • The proposed method enables sap flux density measurements to be made across the entire natural occurring sap flux density range of woody plants. Moreover, the water content during low flows can be determined accurately, enabling a correct conversion from heat velocity to sap flux density without destructive core measurements. © 2012 The Authors. New Phytologist © 2012 New Phytologist Trust.

  15. Intact plant magnetic resonance imaging to study dynamics in long-distance sap flow and flow-conducting surface area

    NARCIS (Netherlands)

    Scheenen, T.W.J.; Vergeldt, F.J.; Heemskerk, A.M.; As, van H.

    2007-01-01

    Due to the fragile pressure gradients present in the xylem and phloem, methods to study sap flow must be minimally invasive. Magnetic resonance imaging (MRI) meets this condition. A dedicated MRI method to study sap flow has been applied to quantify long-distance xylem flow and hydraulics in an

  16. Optimization of dry - season sap flow measurements in an oak semi - arid open woodland in Spain

    NARCIS (Netherlands)

    Reyes-Acosta, J.L.; Lubczynski, M.

    2014-01-01

    In sap flow studies, there is no method complying with high efficiency and versatility of sap flow measurements. To improve that, we propose combining two methods: (1) thermal dissipation probe (TDP) known to be efficient and cost effective and (2) heat field deformation (HFD) known to be versatile.

  17. A comparison of methods for determining the cotton field evapotranspiration and its components under mulched drip irrigation conditions: photosynthesis system, sap flow, and eddy covariance

    Science.gov (United States)

    Zhang, Z.; Tian, F.; Hu, H.

    2013-12-01

    A multi-scale, multi-technique study was conducted to measure evapotranspiration and its components in a cotton field under mulched drip irrigation conditions in northwestern China. Three measurement techniques at different scales were used: photosynthesis system (leaf scale), sap flow (plant scale), and eddy covariance (field scale). The experiment was conducted from July to September 2012. For upscaling the evapotranspiration from the leaf to the plant scale, an approach that incorporated the canopy structure and the relationships between sunlit and shaded leaves was proposed. For upscaling the evapotranspiration from the plant to the field scale, an approach based on the transpiration per unit leaf area was adopted and modified to incorporate the temporal variability in the relationships between the leaf area and the stem diameter. At the plant scale, the estimate of the transpiration based on the photosynthesis system with upscaling is slightly higher (18%) than that obtained by sap flow. At the field scale, the estimate of the transpiration obtained by upscaling the estimate based on sap flow measurements is also systematically higher (10%) compared to that obtained through eddy covariance during the cotton open boll growth stage when soil evaporation can be neglected. Nevertheless, the results derived from these three distinct methods show reasonable consistency at the field scale, which indicates that the upscaling approaches are reasonable and valid. Based on the measurements and the upscaling approaches, the evapotranspiration components were analyzed under mulched drip irrigation. During the cotton flower and bolling stages in July and August, the evapotranspiration are 3.94 and 4.53 mm day-1, respectively. The proportion of transpiration to evapotranspiration reaches 87.1% before drip irrigation and 82.3% after irrigation. The high water use efficiency is principally due to the mulched film above the drip pipe, the low soil water content in the inter

  18. Influence of auroral streamers on rapid evolution of SAPS flows

    Science.gov (United States)

    Gallardo-Lacourt, B.; Nishimura, T.; Lyons, L. R.; Ruohoniemi, J. M.; Donovan, E.; Angelopoulos, V.; Nishitani, N.

    2015-12-01

    An important manifestation of plasma transport in the ionosphere is Subauroral Polarization Streams or SAPS, which are strong westward flow lying just equatorward of the electron auroral oval and thus of enhanced ionospheric conductivities of the auroral oval. While SAPS are known to intensify due to substorm injections, recent studies showed that large variability of SAPS flow can occur well after substorm onset and even during non-substorm times. These SAPS enhancements have been suggested to occur in association with auroral streamers that propagate equatorward, a suggestion that would indicate that plasma sheet fast flows propagate into the inner magnetosphere and increase subauroral flows. We present auroral images from the THEMIS ground-based all-sky-imager array and 2-d line-of-sight flow observations from the SuperDARN radars that share fields of view with the imagers to investigate systematically the association between SAPS and auroral streamers. We surveyed events from December 2007 to April 2013 for which high or mid-latitude SuperDARN radars were available to measure the SAPS flows, and identified 60 events. For streamers observed near the equatorward boundary of the auroral oval, we find westward flow enhancements of ~200 m/s slightly equatorward of the streamers. A preliminary survey suggests that >90% of the streamers that reach close to the equatorward boundary lead to westward flow enhancements. We also characterize the SAPS flow channel width and timing relative to streamers reaching radar echo meridians. The strong influence of auroral streamers on rapid SAPS flow evolution suggests that transient fast earthward plasma sheet flows can lead to westward SAPS flow enhancements in the subauroral region, and that such enhancements are far more common than only during substorms because of the frequent occurrences of streamers under various geomagnetic conditions.

  19. Radial variation in sap flow in five laurel forest tree species in Tenerife, Canary Islands.

    Science.gov (United States)

    Jiménez, M. Soledad; Nadezhdina, Nadezhda; Cermák, Jan; Morales, Domingo

    2000-11-01

    Variations in radial patterns of xylem water content and sap flow rate were measured in five laurel forest tree species (Laurus azorica (Seub.) Franco, Persea indica (L.) Spreng., Myrica faya Ait., Erica arborea L. and Ilex perado Ait. ssp. platyphylla (Webb & Berth.) Tutin) growing in an experimental plot at Agua García, Tenerife, Canary Islands. Measurements were performed around midday during warm and sunny days by the heat field deformation method. In all species, water content was almost constant (around 35% by volume) over the whole xylem cross-sectional area. There were no differences in wood color over the whole cross-sectional area of the stem in most species with the exception of E. arborea, whose wood became darker in the inner layers. Radial patterns of sap flow were highly variable and did not show clear relationships with tree diameter or species. Sap flow occurred over the whole xylem cross-sectional area in some species, whereas it was limited to the outer xylem layers in others. Sap flow rate was either similar along the xylem radius or exhibited a peak in the outer part of the xylem area. Low sap flow rates with little variation in radial pattern were typical for shaded suppressed trees, whereas dominant trees exhibited high sap flow rates with a peak in the radial pattern. Stem damage resulted in a significant decrease in sap flow rate in the outer xylem layers. The outer xylem is more important for whole tree water supply than the inner xylem because of its larger size. We conclude that measurement of radial flow pattern provides a reliable method of integrating sap flow from individual measuring points to the whole tree.

  20. Sap flow measurements combining sap-flux density radial profiles with punctual sap-flux density measurements in oak trees (Quercus ilex and Quercus pyrenaica) - water-use implications in a water-limited savanna-

    Science.gov (United States)

    Reyes, J. Leonardo; Lubczynski1, Maciek W.

    2010-05-01

    Sap flow measurement is a key aspect for understanding how plants use water and their impacts on the ecosystems. A variety of sensors have been developed to measure sap flow, each one with its unique characteristics. When the aim of a research is to have accurate tree water use calculations, with high temporal and spatial resolution (i.e. scaled), a sensor with high accuracy, high measurement efficiency, low signal-to-noise ratio and low price is ideal, but such has not been developed yet. Granier's thermal dissipation probes (TDP) have been widely used in many studies and various environmental conditions because of its simplicity, reliability, efficiency and low cost. However, it has two major flaws when is used in semi-arid environments and broad-stem tree species: it is often affected by high natural thermal gradients (NTG), which distorts the measurements, and it cannot measure the radial variability of sap-flux density in trees with sapwood thicker than two centimeters. The new, multi point heat field deformation sensor (HFD) is theoretically not affected by NTG, and it can measure the radial variability of the sap flow at different depths. However, its high cost is a serious limitation when simultaneous measurements are required in several trees (e.g. catchment-scale studies). The underlying challenge is to develop a monitoring schema in which HFD and TDP are combined to satisfy the needs of measurement efficiency and accuracy in water accounting. To assess the level of agreement between TDP and HFD methods in quantifying sap flow rates and temporal patterns on Quercus ilex (Q.i ) and Quercus pyrenaica trees (Q.p.), three measurement schemas: standard TDP, TDP-NTG-corrected and HFD were compared in dry season at the semi-arid Sardon area, near Salamanca in Spain in the period from June to September 2009. To correct TDP measurements with regard to radial sap flow variability, a radial sap flux density correction factor was applied and tested by adjusting TDP

  1. Sap flow of the major tree species in the eastern mountainous region in northeast China

    Institute of Scientific and Technical Information of China (English)

    SUN Huizhen; SUN Long; WANG Chuankuan; ZHOU Xiaofeng

    2006-01-01

    This study is based on Quercus mongolica,Fraxinus mandshurica, Phellodendron amurense,Juglans mandshurica,Tilia amurensis,and Pinus koraiensis trees of the same age (12 years) and seedling origin under the same site conditions.The sap flow density,water consumption,and related environmental factors were also measured using thermal dissipation method and ICT-2000TE (Transpiration-Environment) automatic measuring system for tree transpiration and environmental factors.On clear days during the growing season,the sap flow density exhibited mono-peak diurnal patterns,mostly between 10:00 and 14:00,except for Phellodendron amurense,whose sap flow showed two peaks during the daytime three times.The photosynthetically active radiation (PAR) and vapour pressure deficit (VPD) were the major factors influencing diurnal changes in sap flow,which explained 60%-74% variations in sap flow density for all species except Phellodendron amurense.Maximum sap flow densities for F.mandshurica,Phellodendron amurense,Q.mongolica,J.mandshurica,T.amurensis,and Pinus koraiensis were 516.36,234.00,625.93,945.83,507.93,and 286.21 July,respectively.Water consumption during the whole growing season for J.mandshurica, T.amurensis,F.mandshurica,Pinus koraiensis,Phellodendron amurense,and Q.mongolica was 3,840,2,820,2,710,2,120,1,470,and 1,390 kg/sapling,respectively.

  2. SAP FLOW RESPONSE OF CHERRY TREES TO WEATHER CONDITION

    Directory of Open Access Journals (Sweden)

    Á. JUHÁSZ

    2011-03-01

    Full Text Available Sap flow response of cherry trees to weather condition. Themain goal of our study is to measure water-demand of cherry trees budded ontodifferent rootstocks by sapflow equipment and to study the sap flow response to themeteorological factors. The investigations are carried out in Soroksár in Hungary at‘Rita’ sweet cherry orchard. The pattern of sapflow was analyzed in relation ofsolar radiation, vapour pressure deficit and air temperature. Between solar radiationand sap flow was found a parabolic relation, daily pattern of sapflow is in closerelation (cubic also to vapour pressure deficit. No significant relationship existedbetween sapflow and air temperature. The sapflow performance of sweet cherrytrees on different rootstocks showed typical daily characters.

  3. Use of the correct heat conduction-convection equation as basis for heat-pulse sap flow methods in anisotropic wood.

    Science.gov (United States)

    Vandegehuchte, Maurits W; Steppe, Kathy

    2012-05-01

    Heat-pulse methods to determine sap flux density in trees are founded on the theory of heat conduction and heat convection in an isotropic medium. However, sapwood is clearly anisotropic, implying a difference in thermal conductivity along and across the grain, and hence necessitates the theory for an anisotropic medium. This difference in thermal conductivities, which can be up to 50%, is, however, not taken into account in the key equation leading to the currently available heat-pulse methods. Despite this major flaw, the methods remain theoretically correct as they are based on derivations of the key equation, ruling out any anisotropic aspects. The importance of specifying the thermal characteristics of the sapwood according to axial, tangential or radial direction is revealed as well as referring to and using the proper anisotropic theory in order to avoid confusion and misinterpretation of thermal properties when dealing with sap flux density measurements or erroneous results when modelling heat transport in sapwood.

  4. SAP

    DEFF Research Database (Denmark)

    Petersen, Bent; Nikerle-Uhthoff, Dominique; Schwaerzler, Helen

    2014-01-01

    In late 2011, SAP, the German leader in the enterprise software industry, announced a major investment plan for expanding in China and also acquired a leading American firm in cloud-based human capital management software. At first glance, these investments seemed rather unconnected. A closer loo...... strategies? Compared to its key competitors — Microsoft, IBM and Oracle — how was it aligning its innovation strategy with its sourcing strategy?...

  5. Sap flow is Underestimated by Thermal Dissipation Sensors due to Alterations of Wood Anatomy

    Science.gov (United States)

    Marañón-Jiménez, S.; Wiedemann, A.; van den Bulcke, J.; Cuntz, M.; Rebmann, C.; Steppe, K.

    2014-12-01

    The thermal dissipation technique (TD) is one of the most commonly adopted methods for sap flow measurements. However, underestimations of up to 60% of the tree transpiration have been reported with this technique, although the causes are not certainly known. The insertion of TD sensors within the stems causes damage of the wood tissue and subsequent healing reactions, changing wood anatomy and likely the sap flow path. However, the anatomical changes in response to the insertion of sap flow sensors and the effects on the measured flow have not been assessed yet. In this study, we investigate the alteration of vessel anatomy on wounds formed around TD sensors. Our main objectives were to elucidate the anatomical causes of sap flow underestimation for ring-porous and diffuse-porous species, and relate these changes to sap flow underestimations. Successive sets of TD probes were installed in early, mid and end of the growing season in Fagus sylvatica (diffuse-porous) and Quercus petraea (ring-porous) trees. They were logged after the growing season and additional sets of sensors were installed in the logged stems with presumably no healing reaction. The wood tissue surrounding each sensor was then excised and analysed by X-ray computed microtomography (X-ray micro CT). This technique allowed the quantification of vessel anatomical characteristics and the reconstruction of the 3-D internal microstructure of the xylem vessels so that extension and shape of the altered area could be determined. Gels and tyloses clogged the conductive vessels around the sensors in both beech and oak. The extension of the affected area was larger for beech although these anatomical changes led to similar sap flow underestimations in both species. The higher vessel size in oak may explain this result and, therefore, larger sap flow underestimation per area of affected conductive tissue. The wound healing reaction likely occurred within the first weeks after sensor installation, which

  6. [Time lag effect between poplar' s sap flow velocity and microclimate factors in agroforestry system in West Liaoning Province].

    Science.gov (United States)

    Di, Sun; Guan, De-xin; Yuan, Feng-hui; Wang, An-zhi; Wu, Jia-bing

    2010-11-01

    By using Granier's thermal dissipation probe, the sap flow velocity of the poplars in agroforestry system in west Liaoning was continuously measured, and the microclimate factors were measured synchronously. Dislocation contrast method was applied to analyze the sap flow velocity and corresponding air temperature, air humidity, net radiation, and vapor pressure deficit to discuss the time lag effect between poplar' s sap flow velocity and microclimate factors on sunny days. It was found that the poplar's sap flow velocity advanced of air temperature, air humidity, and vapor pressure deficit, and lagged behind net radiation. The sap flow velocity in June, July, August, and September was advanced of 70, 30, 50, and 90 min to air temperature, of 80, 30, 40, and 90 min to air humidity, and of 90, 50, 70, and 120 min to vapor pressure deficit, but lagged behind 10, 10, 40, and 40 min to net radiation, respectively. The time lag time of net radiation was shorter than that of air temperature, air humidity, and vapor pressure. The regression analysis showed that in the cases the time lag effect was contained and not, the determination coefficients between comprehensive microclimate factor and poplar's sap flow velocity were 0.903 and 0.855, respectively, indicating that when the time lag effect was contained, the determination coefficient was ascended by 2.04%, and thus, the simulation accuracy of poplar's sap flow velocity was improved.

  7. Sap flow measurement in a street and park of a hot and arid city

    Science.gov (United States)

    Cohen, S.; Shashua-Bar, L.; Potchter, O.; Yaakov, Y.; Bar-Kutiel, P.; Tanny, J.

    2012-04-01

    Urban trees mitigate hot climate by shading, but also through transpirational cooling. Transpiration from urban trees can be a significant part of the urban energy budget, but is difficult to quantify. A direct method for measuring tree transpiration is through the use of sap flow sensors. Several methods have been developed for this, where the most common use heat as a tracer of sap flow. The most popular method among plant environmental ecologists is the thermal dissipation or 'Granier' method, the latter name for its inventor. In this method continuously heated and unheated sensors are inserted into the tree stem and the temperature difference between the two is roughly inversely proportional to sap flux density. Although the method can be accurate, sap flux density can be highly variable in the stem, depending on depth in the stem and azimuth. Inter-tree variation is also large, so a number of sensors per tree and a number of trees need to be monitored for accurate determinations. Finally, it is a good idea to calibrate the sensors for the configuration and species being monitored. We measured sap flow in a tree covered open mall and a city park in Beer Sheva, Israel - a hot and arid city. Trees that shaded the open mall were of the Delonix regia species while those in the park were Prosopis and Tamarix sp. Individual tree sap flux for large trees exceeded 100 liters on many of the days, equivalent to over 100 W m-2 at mid-day. This paper will discuss methodological issues as well as some of the results.

  8. Sap flow and sugar transport in plants

    Science.gov (United States)

    Jensen, K. H.; Berg-Sørensen, K.; Bruus, H.; Holbrook, N. M.; Liesche, J.; Schulz, A.; Zwieniecki, M. A.; Bohr, T.

    2016-07-01

    Green plants are Earth's primary solar energy collectors. They harvest the energy of the Sun by converting light energy into chemical energy stored in the bonds of sugar molecules. A multitude of carefully orchestrated transport processes are needed to move water and minerals from the soil to sites of photosynthesis and to distribute energy-rich sugars throughout the plant body to support metabolism and growth. The long-distance transport happens in the plants' vascular system, where water and solutes are moved along the entire length of the plant. In this review, the current understanding of the mechanism and the quantitative description of these flows are discussed, connecting theory and experiments as far as possible. The article begins with an overview of low-Reynolds-number transport processes, followed by an introduction to the anatomy and physiology of vascular transport in the phloem and xylem. Next, sugar transport in the phloem is explored with attention given to experimental results as well as the fluid mechanics of osmotically driven flows. Then water transport in the xylem is discussed with a focus on embolism dynamics, conduit optimization, and couplings between water and sugar transport. Finally, remarks are given on some of the open questions of this research field.

  9. Sap flow and sugar transport in plants

    DEFF Research Database (Denmark)

    Jensen, Kaare Hartvig; Berg-Sørensen, Kirstine; Bruus, Henrik

    2016-01-01

    Green plants are Earth’s primary solar energy collectors. They harvest the energy of the Sun by converting light energy into chemical energy stored in the bonds of sugar molecules. A multitude of carefully orchestrated transport processes are needed to move water and minerals from the soil to sites...... of photosynthesis and to distribute energy-rich sugars throughout the plant body to support metabolism and growth. The long-distance transport happens in the plants’ vascular system, where water and solutes are moved along the entire length of the plant. In this review, the current understanding of the mechanism...... and the quantitative description of these flows are discussed, connecting theory and experiments as far as possible. The article begins with an overview of low-Reynolds-number transport processes, followed by an introduction to the anatomy and physiology of vascular transport in the phloem and xylem. Next, sugar...

  10. Impact of the Mekong River flow alteration on the Tonle Sap flood pulse.

    Science.gov (United States)

    Kummu, Matti; Sarkkula, Juha

    2008-05-01

    Rapid development in the upper reaches of the Mekong River, in the form of construction of large hydropower dams and reservoirs, large irrigation schemes, and rapid urban development, is putting water resources under stress. Recent studies have concluded that these developments will lead to flow alterations in the Mekong River. These flow alterations would threaten the sensitive ecosystems downstream, particularly Tonle Sap River, Tonle Sap Lake, its floodplain, and its gallery forest and protected areas, by changing the flood-pulse system of the lake. This article estimates the changes in parameters of the Tonle Sap flood pulse due to the aforementioned flow alterations. The impacts on the flooded area and loss of gallery forest and protected areas were analyzed using geographic information system-based methods. Relatively small rises in the dry-season lake water level would permanently inundate disproportionately large areas of floodplain, rendering it inaccessible to floodplain vegetation and eroding the productivity basis of the ecosystem. It is highly important to maintain the natural hydrological pattern of the Mekong River, particularly the dry-season water levels, to preserve Tonle Sap Lake's ecosystem productivity.

  11. Sap flow measurements to determine the transpiration of facade greenings

    Science.gov (United States)

    Hölscher, Marie-Therese; Nehls, Thomas; Wessolek, Gerd

    2014-05-01

    Facade greening is expected to make a major contribution to the mitigation of the urban heat-island effect through transpiration cooling, thermal insulation and shading of vertical built structures. However, no studies are available on water demand and the transpiration of urban vertical green. Such knowledge is needed as the plants must be sufficiently watered, otherwise the posited positive effects of vertical green can turn into disadvantages when compared to a white wall. Within the framework of the German Research Group DFG FOR 1736 "Urban Climate and Heat Stress" this study aims to test the practicability of the sap flow technique for transpiration measurements of climbing plants and to obtain potential transpiration rates for the most commonly used species. Using sap flow measurements we determined the transpiration of Fallopia baldschuanica, Parthenocissus tricuspidata and Hedera helix in pot experiments (about 1 m high) during the hot summer period from August 17th to August 30th 2012 under indoor conditions. Sap flow measurements corresponded well to simultaneous weight measurement on a daily base (factor 1.19). Fallopia baldschuanica has the highest daily transpiration rate based on leaf area (1.6 mm d-1) and per base area (5.0 mm d-1). Parthenocissus tricuspidata and Hedera helix show transpiration rates of 3.5 and 0.4 mm d-1 (per base area). Through water shortage, transpiration strongly decreased and leaf temperature measured by infrared thermography increased by 1 K compared to a well watered plant. We transferred the technique to outdoor conditions and will present first results for facade greenings in the inner-city of Berlin for the hottest period in summer 2013.

  12. Measurement and modelling of sap flow in maize plants

    Science.gov (United States)

    Heinlein, Florian; Biernath, Christian; Hoffmann, Peter; Klein, Christian; Thieme, Christoph; Priesack, Eckart

    2014-05-01

    Climate change as well as the changing composition of the atmosphere will have an impact on future yield of agricultural plants. In order to better estimate these impacts new, mechanistic plant growth models are needed. These models should be able to dynamically reproduce the plants' reactions to modified climate state variables like temperature, atmospheric CO2-concentration and water availability. In particular, to better describe the crop response to more strongly changing water availability the simulation of plant-internal water and solute transport processes in xylem and phloem needs to be improved. Our existing water transport model consists of two coupled 1-D Richards equations to calculate water transport in the soil and in the plants. This model has already been successfully applied to single Fagus sylvatica L. trees. At present it is adapted to agricultural plants such as maize. To simulate the water transport within the plants a representation of the flow paths, i.e. the plant architecture, is required. Aboveground plant structures are obtained from terrestrial laser scan (TLS) measurements at different development stages. These TLSs have been executed at the lysimeter facilities of Helmholtz Zentrum München and at the TERENO (Terrestrial Environmental Observatories) research farm Scheyern. Additionally, an L-system model is used to simulate aboveground and belowground plant architectures. In a further step, the quality of the explicit water flow model has to be tested using measurements. The Heat-Ratio-Method has been employed to directly measure sap flow in larger maize plants during a two-months-period in summer 2013 with a resolution of 10 minutes and thus, the plants' transpiration can be assessed. Water losses from the soil are determined by measuring the weight of lysimeters. From this evapotranspiration can be calculated. Transpiration and evapotranspiration are also simulated by application of the modelling system Expert-N. This framework

  13. [Application of thermal dissipation probe in the study of Bambusa chungii sap flow].

    Science.gov (United States)

    Zhao, Ping; Mei, Ting-Ting; Ni, Guang-Yan; Yu, Meng-Hao; Zeng, Xiao-Ping

    2012-04-01

    Based on the validation of Granier's empirical formula for calculating tree stem sap flux density, a comparative study was conducted on the measurement of Bambusa chungi sap flow by using different lengths of thermal dissipation probe (TDP), aimed to approach the applicability of TDP in measuring the sap flow of B. chungii. The difference in the daily change of the sap flow between B. chungii and nearby growing Schima superb was also analyzed. Because of the thinner bamboo wall and the heterogeneous anatomy, the sap flux density of B. chungii measured by 10 mm long probe could be underestimated, but that measured by 8 and 5 mm long probes could be relatively accurate. The comparison of the sap flow between B. chungii and nearby growing S. superba revealed that both the mean sap flux density and its daily change pattern' s skewness of B. chungii were higher than those of S. superba, but the nighttime sap flow of B. chungii was less than that of S. superba, indicating that the water recharge of B. chungii during nighttime was less active than that of S. superba. It was suggested that using TDP to investigate the sap flow of bamboo would be feasible, but careful calibration would be required before the TDP was put into application on different bamboo species.

  14. Piloting the use of indigenous methods to prevent Nipah virus infection by interrupting bats' access to date palm sap in Bangladesh.

    Science.gov (United States)

    Nahar, Nazmun; Mondal, Utpal Kumar; Sultana, Rebeca; Hossain, M Jahangir; Khan, M Salah Uddin; Gurley, Emily S; Oliveras, Elizabeth; Luby, Stephen P

    2013-09-01

    People in Bangladesh frequently drink fresh date palm sap. Fruit bats (Pteropus giganteus) also drink raw sap and may contaminate the sap by shedding Nipah virus through saliva and urine. In a previous study we identified two indigenous methods to prevent bats accessing the sap, bamboo skirts and lime (calcium carbonate). We conducted a pilot study to assess the acceptability of these two methods among sap harvesters. We used interactive community meetings and group discussions to encourage all the sap harvesters (n = 12) from a village to use either bamboo skirts or lime smear that some of them (n = 4) prepared and applied. We measured the preparation and application time and calculated the cost of bamboo skirts. We conducted interviews after the use of each method. The sap harvesters found skirts effective in preventing bats from accessing sap. They were sceptical that lime would be effective as the lime was washed away by the sap flow. Preparation of the skirt took ∼105 min. The application of each method took ∼1 min. The cost of the bamboo skirt is minimal because bamboo is widely available and they made the skirts with pieces of used bamboo. The bamboo skirt method appeared practical and affordable to the sap harvesters. Further studies should explore its ability to prevent bats from accessing date palm sap and assess if its use produces more or better quality sap, which would provide further incentives to make it more acceptable for its regular use.

  15. Estimating sap flux densities in date palm trees using the heat dissipation method and weighing lysimeters.

    Science.gov (United States)

    Sperling, Or; Shapira, Or; Cohen, Shabtai; Tripler, Effi; Schwartz, Amnon; Lazarovitch, Naftali

    2012-09-01

    In a world of diminishing water reservoirs and a rising demand for food, the practice and development of water stress indicators and sensors are in rapid progress. The heat dissipation method, originally established by Granier, is herein applied and modified to enable sap flow measurements in date palm trees in the southern Arava desert of Israel. A long and tough sensor was constructed to withstand insertion into the date palm's hard exterior stem. This stem is wide and fibrous, surrounded by an even tougher external non-conducting layer of dead leaf bases. Furthermore, being a monocot species, water flow does not necessarily occur through the outer part of the palm's stem, as in most trees. Therefore, it is highly important to investigate the variations of the sap flux densities and determine the preferable location for sap flow sensing within the stem. Once installed into fully grown date palm trees stationed on weighing lysimeters, sap flow as measured by the modified sensors was compared with the actual transpiration. Sap flow was found to be well correlated with transpiration, especially when using a recent calibration equation rather than the original Granier equation. Furthermore, inducing the axial variability of the sap flux densities was found to be highly important for accurate assessments of transpiration by sap flow measurements. The sensors indicated no transpiration at night, a high increase of transpiration from 06:00 to 09:00, maximum transpiration at 12:00, followed by a moderate reduction until 08:00; when transpiration ceased. These results were reinforced by the lysimeters' output. Reduced sap flux densities were detected at the stem's mantle when compared with its center. These results were reinforced by mechanistic measurements of the stem's specific hydraulic conductivity. Variance on the vertical axis was also observed, indicating an accelerated flow towards the upper parts of the tree and raising a hypothesis concerning dehydrating

  16. An Empirical Study of the Wound Effects on Sap Flow Measured with Thermal Dissipation Probes

    Science.gov (United States)

    Wiedemann, A.; Marañón-Jiménez, S.; Herbst, M.; Cuntz, M.; Rebmann, C.

    2014-12-01

    Sap flow sensors are common to assess the contribution of tree transpiration to ecosystem evapotranspiration (ET). Thermal dissipation (TD) is one of the most popular methods for sap measurements but the insertion of TD probes in the tree stems imply wounding of the wood tissue and a consequent alteration of the sap flow. But the determination of sap flux density (SFD) is based on an empirical function developed for freshly drilled holes and it does hence not account for the wound effect. Here we investigate the effect of wound healing on sap flow measurements with TD probes. Our objectives were (1) the establishment of correction factors to account for the wound effect and (2) the determination of the point in time after installation when the correction factors become applicable. For that we performed an experiment in which TD probes were installed successively in diffuse- and ring-porous trees (Fagus sylvatica and Quercus petraea, resp.) during the growing season. The trees were logged in fall and additional sensors were installed afterwards in the logged stems. SFDs measured by the different TD sensors were compared with gravimetric estimates in the laboratory. Gravimetric flow compared well with SFD estimates from freshly installed sensors without wound formation, with only a slight underestimation by the TDs. In contrast, older sensors, submitted to wound reactions, underestimated SFD by up to 40%. However, sensors with 5, 11 and 22 week old wounds showed no significant differences, which implies that wound healing occurs in the first weeks after scission. Similar sap flow underestimations due to wound effects were observed in both species, oak and beech. This study highlights the relevance of accounting for tree wound reactions for accurate estimation of tree transpiration based on thermal dissipation sensors. We provide a correction factor for the classical Granier TD sensors that can be used from the first weeks after installation in similar species. This

  17. The concentration and efflux of tree stem CO2 and the role of xylem sap flow

    Institute of Scientific and Technical Information of China (English)

    Ping ZHAO; Dirk H(O)LSCHER

    2009-01-01

    The accurate assessment of actual tree stem respiration and its relation with temperature plays a considerable role in investigating the forest carbon cycle.An increasing number of research reports have indicated that tree stem respiration determined with the commonlyapplied chamber gas exchange measuring system does not follow expectations regarding temperature relationships.theory that the respired CO2 in a tree stem would all diffuse outward into the atmosphere,However,it neglects partial CO2 that is dissolved in the xylem sap and is carried away by the transpirational stream.Scientists have started to realize that the respired CO2 measured with the chamber gas exchange method is only a portion of the total stem respiration (CO2 efflux),while the other portion,which is sometimes very substantial in quantity (thought to occupy maybe 15%-75% of the total stem respiration),is transported to the upper part of the stem and to the canopy by sap flow.This suggests that the CO2 produced by respiration is re-allocated within the stem.Accordingly,the change in CO2 efflux could be reflected in the rates of sap flow in addition to its dependence on temperature.Proper methods and instruments are required to quantify the internal and external CO2 fluxes in the trunk and their interaction with related environmental factors.

  18. Combining sap flow meas- urement-based canopy stomatal conductance and 13C discrimination to estimate forest carbon assimilation

    Institute of Scientific and Technical Information of China (English)

    ZHAO Ping; LU Ping; MA Ling; SUN Guchou; RAO Xingquan; CAI Xian; ZENG Xiaoping

    2005-01-01

    The available methods for studying C uptake of forest and their problems in practices are reviewed, and a new approach to combining sap flow and 13C techniques is proposed in this paper. This approach, obtained through strict mathematic derivation, combines sap flow measurement-based canopy stomatal conductance and 13C discrimination to estimate instantaneous carbon assimilation rate of a forest. Namely the mean canopy stomatal conductance (gc) acquired from accurate measurement of sap flux density is integrated with the relationship between 13C discrimination (() and Ci/Ca (intercellular/ambient CO2 concentrations) and with that between Anet (net photosynthetic rate) and gCO2 (stomatal conductance for CO2) so that a new relation between forest C uptake and ( as well as gc is established. It is a new method of such kind for studying the C exchange between forest and atmosphere based on experimental ecology.

  19. [Characteristics of dominant tree species stem sap flow and their relationships with environmental factors in a mixed conifer-broadleaf forest in Dinghushan, Guangdong Province of South China].

    Science.gov (United States)

    Huang, De-Wei; Zhang, De-Qiang; Zhou, Guo-Yi; Liu, Shi-Zhong; Otieno, Dennis; Li, Yue-Lin

    2012-05-01

    By the method of Granier' s thermal dissipation probe, the stem sap flow density of four dominant tree species (Pinus massoniana, Castanopsis chinensis, Schima superba, and Machilus kwangtungensis) in a mixed conifer-broadleaf forest in Dinghushan Reserve of South China was continuously measured in the dry season (November) and wet season (July) in 2010, and the environmental factors including air temperature, relative humidity, and photosynthetically active radiation (PAR) were measured synchronically, aimed to study the characteristics of the stem sap flow of the tree species in response to environmental factors. During the dry and wet seasons, the diurnal changes of the stem sap flow velocity of the tree species all presented a typical single-peak curve, with high values in the daytime and low values in the nighttime. The average and maximum sap flow velocities and the daily sap flow flux of broad-leaved trees (C. chinensis, S. superba, and M. kwangtungensis) were significantly higher than those of coniferous tree (P. massoniana), and the maximum sap flow velocity of P. massoniana, C. valueschinensis, S. superba, and M. kwangtungensis was 29.48, 38.54, 51.67 and 58.32 g H2O x m(-2) x s(-1), respectively. A time lag was observed between the sap flow velocity and the diurnal variations of PAR, vapor pressure deficiency, and air temperature, and there existed significant positive correlations between the sap flow velocity and the three environmental factors. The PAR in wet season and the air temperature in dry season were the leading factors affecting the stem sap flow velocity of the dominant tree species.

  20. A single-probe heat pulse method for estimating sap velocity in trees.

    Science.gov (United States)

    López-Bernal, Álvaro; Testi, Luca; Villalobos, Francisco J

    2017-10-01

    Available sap flow methods are still far from being simple, cheap and reliable enough to be used beyond very specific research purposes. This study presents and tests a new single-probe heat pulse (SPHP) method for monitoring sap velocity in trees using a single-probe sensor, rather than the multi-probe arrangements used up to now. Based on the fundamental conduction-convection principles of heat transport in sapwood, convective velocity (Vh ) is estimated from the temperature increase in the heater after the application of a heat pulse (ΔT). The method was validated against measurements performed with the compensation heat pulse (CHP) technique in field trees of six different species. To do so, a dedicated three-probe sensor capable of simultaneously applying both methods was produced and used. Experimental measurements in the six species showed an excellent agreement between SPHP and CHP outputs for moderate to high flow rates, confirming the applicability of the method. In relation to other sap flow methods, SPHP presents several significant advantages: it requires low power inputs, it uses technically simpler and potentially cheaper instrumentation, the physical damage to the tree is minimal and artefacts caused by incorrect probe spacing and alignment are removed. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

  1. Seasonal sap flow of four Salix varieties growing on the Solvay wastebeds in Syracuse, NY, USA.

    Science.gov (United States)

    Mirck, Jaconette; Volk, Timothy A

    2010-01-01

    Sap flow of four shrub willow varieties was measured to study their potential use as an evapotranspiration (ET) cover on the Solvay wastebeds to reduce deep percolation and leaching of chloride. Stem and stand-level sap flow and crop coefficients (K(c)) were different among four willow varieties measured between early June and mid November 2006. Diameter and cross sectional area had a significant impact on stand level sap flow. Peak stand-level sap flow of 7 mm d(-1) occurred in June, due to coupling of the willow with the atmosphere, and not in July or August when peak LAI was measured. The coupling also resulted in high K(c) values of 3 in June and above 2 in October with an average of 1.1-1.3 for the entire season. Our measurements confirmed the potentials of shrub willow in ET cover applications in the northeastern USA. Total transpiration for the growing season ranged between 494 mm and 533 mm, which was about 45% of the precipitation in 2006. Our calculations showed a significant difference between peak season sap flow in June, July and August and sap flow over the course of the whole growing season, which showed the need for long-term measurements.

  2. Sap flow of Castanopsis jianfengensis and its relationship with environmental factors in a tropical montane rainforest

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Using thermal dissipation and the ICT-2000TE equipment made in Australia,the sap flow of Castanopsis jianfengensis and various environmental factors were measured simultaneously in a mixed tropical montane rainforest at Jianfengling Nature Forest Reserve (18°36'N,108°52'E,860 m elevation) during the dry and rainy seasons of 2002.The results show that sap flow velocity of C jianfengensis exhibited a monopeak pattern on clear days and a multi-peak pattern on cloudy or rainy days.Sap flow velocity had significant positive correlations with solar radiation,air temperature,vapor pressure deficit and wind speed and a negative correlation with air relative humidity.In the dry season,sap flow velocity had a significant positive correlation with soil temperature and poor correlation with soil moisture;it was the opposite in the rainy season,indicating that precipitation clearly affected sap flow.Linear regression models between sap flow and environmental factors were established and were significant at the 0.005 level of probability.The mean transpiration rates of C.jianfengensis were 103.5 and 41.3 kg/d in our single tree and 1.94 and 0.77 mm/d in stand level in the dry and rainy season,respectively.

  3. Desempenho do método de dissipação térmica na medida do fluxo de seiva em seringueira Performance of a thermal dissipation method for sap flow measurement in rubber tree

    Directory of Open Access Journals (Sweden)

    Juan S. Delgado-Rojas

    2006-12-01

    Full Text Available A medida da transpiração de árvores no campo é de difícil consecução. Nas duas últimas décadas, tem-se dado ênfase à medida de fluxo de seiva no caule como indicador da transpiração, principalmente se a escala de tempo usada é igual ou menor que um dia. Para essas medidas, são usados métodos térmicos com fornecimento de calor ao caule. O método de dissipação térmica (MDT é um deles e vem sendo bastante utilizado pelo seu princípio simples e pela boa sensibilidade às variações de fluxo de seiva. Entretanto, tem-se evidenciado a necessidade de cuidados no seu uso, sendo uma das causas de perda de precisão o efeito da carga radiante sobre a planta, geradora de gradiente térmico natural, que interfere nos resultados. Além disso, o desempenho do método em condições diferentes daquelas em que foi desenvolvido deve ser testado. Assim, o presente trabalho teve como objetivos analisar o desempenho do MDT em árvores de seringueira, considerando que essa espécie produz látex que poderia interferir sobre o bom funcionamento do sensor, e avaliar o efeito do gradiente térmico natural do caule sobre as estimativas. Os resultados demonstraram que essa técnica de medida pode ser utilizada nessa espécie e que, nas condições em que foram realizados os testes, não há interferência do gradiente térmico natural sobre as estimativas. Entretanto, para melhorar o grau de precisão, deve ser realizado melhor estudo de caraterização da área condutora da seiva em relação ao diâmetro do caule.The transpiration measurement of trees in field condition is very difficult. In the two last decades, some emphasis has been given in the study of stem sap flow as an indicator of plant transpiration. The methodology is particularly suitable for time scale less or equal than one day. One of the methods is the heat dissipation method (HDM, which has been used because of its simplicity and high sensitivity to the sap flow variations

  4. Granier's Thermal Dissipation Probe (TDP) Method for Measuring Sap Flow in Trees:Theory and Practice%应用Granier热消散探针(TDP)法测定树木的木质部液流:理论与实践

    Institute of Scientific and Technical Information of China (English)

    陆平; Laurent URBAB; 赵平

    2004-01-01

    Granier热消散探针法是目前研究树木生理生态和森林水文最常用的测定整树水分利用的方法之一.然而,已有的相关综述文献中,还没有专门介绍利用Granier热消散探针研究木质部液流的综述文章.本文重点介绍了Granier热消散探针测定系统的理论基础,对有关该探针的校准和改进的最新研究进展进行了综述,并还深入探讨了零液流信号值的确定、自然热梯度、损伤效应、液流的逆格型和将木质部液流密度外推至整树蒸腾耗水量等重要的实际问题.%Granier sap flow system is one of the most commonly used techniques for measurements of whole-tree water use in ecophysiological and forest hydrological studies. However, in the literature there is not one paper that exclusively reviews the Granier method. In this paper, we recapitulate the theoretical basis of the Granier sap flow system and review recent developments in calibration and modification of the sensor probes. Practical issues, such as the determination of the non-flow signal values, natural thermal gradient, wounding effect, reversed sap flow pattern and extrapolation of individual measurement of sap flux density to whole-tree sap flow, are discussed in detail. In the perspectives, new approaches are put forward to use the strong coupling between photosynthesis and transpiration or canopy conductance, via the measurement of 13C discrimination, to estimate whole-canopy carbon assimilation.

  5. [Dynamic change of Yulania sap flow before dormancy in response to environmental factors].

    Science.gov (United States)

    Zhu, Zhong-Long; Jia, Zhong-Kui; Ma, Lu-Yi; Wang, Xiao-Ling; Duan, Jie

    2012-09-01

    From September 26 to November 5, 2011, the sap flow of Yulania wufengensis trees including cold-resistance type (HK) and non cold-resistance type (HF), Y. 'Sunspire' (HY), and Yulania x soulangeana (EQ) which were introduced into Beijing four years before was monitored by Flow-32 stem heat balance sensor, and, in combining with the environmental factors monitored synchronically, the changes of the sap flow before dormancy and the environmental factors were analyzed, with the responses of the sap flow to the environmental factors investigated at the scales of 0.5 h and 1 day. The sap flow of the Yulanias trees before dormancy displayed an obvious trend of declining day by day. The environmental factors affecting the sap flow could be divided into two categories, i. e., meteorological index (MI) and soil index (SI). The sap flow of the Yulanias trees had a synchronous variation rhythm with MI, and declined in parallel to SI. The combined effect of MI and SI on the diurnal changes of the sap flow was 69% - 73%. At both 0.5 h and 1 day scales, the sap flow showed significantly correlations with total radiation (Rs), air vapor pressure deficit (D), air relative humidity (RH), air temperature (Ta), and wind speed (w). The sap flow showed no significant correlations with soil temperature (Ts) and soil water content (SWC) at 0. 5 h scale, but had significant correlations with Ts, SWC, and day length (Z) at 1 day scale (the correlation efficient was about 0.8). Only Rs, Z, and D were included into the model at 1 day scale, but almost all environmental factors (except SWC and Ts) were included in the model at 0.5 h scale. Except for HF type, the regression coefficients of the model for the Yulanias trees at 1 day scale (0.92-0.96) were larger than those at 0.5 h scale (0.77-0.87), and the correlations between the dynamic changes of sap flow and the environmental factor were consistent, which was in accord with the fact that the HF could not overwinter in Beijing but the

  6. Use of sap flow measurements to validate stomatal functions for mature beech (Fagus sylvatica) in view of ozone uptake calculations

    Energy Technology Data Exchange (ETDEWEB)

    Braun, Sabine, E-mail: sabine.braun@iap.c [Institute for Applied Plant Biology, Sangrubenstrasse 25, CH-4124 Schoenenbuch (Switzerland); Schindler, Christian [Swiss Tropical and Public Health Institute, University of Basel, Socinstrasse 57, CH-4051 Basel (Switzerland); Leuzinger, Sebastian [Forest Ecology, Institute of Terrestrial Ecosystems, ETH Zurich, Universitaetsstr. 16, 8092 Zuerich (Switzerland)

    2010-09-15

    For a quantitative estimate of the ozone effect on vegetation reliable models for ozone uptake through the stomata are needed. Because of the analogy of ozone uptake and transpiration it is possible to utilize measurements of water loss such as sap flow for quantification of ozone uptake. This technique was applied in three beech (Fagus sylvatica) stands in Switzerland. A canopy conductance was calculated from sap flow velocity and normalized to values between 0 and 1. It represents mainly stomatal conductance as the boundary layer resistance in forests is usually small. Based on this relative conductance, stomatal functions to describe the dependence on light, temperature, vapour pressure deficit and soil moisture were derived using multivariate nonlinear regression. These functions were validated by comparison with conductance values directly estimated from sap flow. The results corroborate the current flux parameterization for beech used in the DO{sub 3}SE model. - A method was developed to derive stomatal functions and ozone uptake calculation from sap flow.

  7. [Analysis of sap flow characteristics of the Chinese pine in typical Loess Plateau Region of China].

    Science.gov (United States)

    Zhang, Han-dan; Wei, Wei; Chen, Li-ding; Yu, Yang; Yang, Lei; Jia, Fu-yan

    2015-01-01

    Transpiration is one of the major processes of water consumption. It is significant for nutrients transportation, plant development, drought stress alleviation and micro-climate amelioration. In this study, the artificially planted Chinese pine (Pinus tabuliformis) was selected as an example to explore its transpiration characteristics, water-use strategies and the adaptability of the living environment in a typical loess hilly area of China. The results showed that: the sap flow rates of Chinese pine varied obviously in different seasons. The minimum sap flow rate occurred in April, followed by October, September and August, which was 0.024, 0.057, 0.062 and 0.071 mL x (cm2 x min)(-1), respectively. The rule of the diurnal variation of sap flow rate was regular, higher in daytime than at night. The flow rate was low during nighttime, but not zero. In rainfall events, the proportion of sap flow during nighttime was significantly increased, which was 3.9 times of that on sunny days, with 31.8% decrease in daytime. Chinese pine had great adaptability to unexpected climates. The variation trend of flow rate in the clod was similar to that on rainy days. The sap flow velocity was in great relevance with meteorological factors, with a declining order of solar radiation, vapor pressure deficit, relative humidity, and atmospheric temperature.

  8. Tree sap flow and stand transpiration of two Acacia mangium plantations in Sabah, Borneo

    Science.gov (United States)

    Cienciala, E.; Kučera, J.; Malmer, A.

    2000-09-01

    Water use of Acacia mangium trees grown in plantations was measured by a heat balance method in two stands that largely differed in tree density. Tree sap flow was closely coupled to climatic drivers and responded with minimal time delay. Using no time shift, sap flow rate could be tightly fitted to a simple equation that combined a parabolic response to radiation and an inverse linear response to air humidity. On the contrary, the analysis of canopy conductance showed no meaningful response to either individual or combined microclimatic variables. No indication of water deficit was observed, though the measurement period was during the dry period of the year. The measurements indicate a minimal diurnal use of water stored in plant tissues. The difference in tree water use from the two studied stands was effectively scaled by tree sapwood area. Canopy transpiration of the densest stand reached in average 3.9 mm d -1 compared with 2.7 mm d -1 for the stand representing the average conditions in the catchment.

  9. [Dynamics of sap flow density in stems of typical desert shrub Calligonum mongolicum and its responses to environmental variables].

    Science.gov (United States)

    Xu, Shi-qin; Ji, Xi-bin; Jin, Bo-wen

    2016-02-01

    Independent measurements of stem sap flow in stems of Calligonum mongolicum and environmental variables using commercial sap flow gauges and a micrometeorological monitoring system, respectively, were made to simulate the variation of sap flow density in the middle range of Hexi Corridor, Northwest China during June to September, 2014. The results showed that the diurnal process of sap flow density in C. mongolicum showed a broad unimodal change, and the maximum sap flow density reached about 30 minutes after the maximum of photosynthetically active radiation (PAR) , while about 120 minutes before the maximum of temperature and vapor pressure deficit (VPD). During the studying period, sap flow density closely related with atmosphere evapor-transpiration demand, and mainly affected by PAR, temperature and VPD. The model was developed which directly linked the sap flow density with climatic variables, and good correlation between measured and simulated sap flow density was observed in different climate conditions. The accuracy of simulation was significantly improved if the time-lag effect was taken into consideration, while this model underestimated low and nighttime sap flow densities, which was probably caused by plant physiological characteristics.

  10. Relationship between effective solar radiation and sap flow process during an entire growing season in Western Mountains of Beijing

    Institute of Scientific and Technical Information of China (English)

    Xu Jun-jiang; Ma Lv-yi

    2007-01-01

    In order to explore the relationship between the time processes of solar radiation and sap flow, sap flow velocity (SFV) of Platycladus orientalis and Pinus tabulaeformis,effective solar radiation (ESR) and other environmental factors wore synchronously monitored for one year in the Beijing Western Mountains by using a thermal dissipation probe (TDP) system and an automatic weather station. Results showed significant differences between changes in diurnal characteristics of ESR and sap flow in sunny days during three seasons. Starting times of sap flow occurred generally 1. 5-3 hours later than those of solar radiation and there were small differences between Platycladus orientalis and Pinus tabulaeformis. But peak times and stopping times of sap flow varied considerably with large contrasts in ESR. The duration of sap flow showed clear differences among the seasons owing to the variable rhythms of climate factors in Beijing. Fluctuation amplitude in the duration of sap flow remained relatively stable during the autumn but changed greatly during spring and summer. Changes in diurnal sap flow velocity of both Platycladus orientalis and Pinus tabulaeformis were about 0-3 hours later than those of ESR but with the same configuration. The start of sap flow was mainly induced by the sudden intensification of ESR (sunrise effect). Seasonal models of SFV indicated that a cubic equation had the best fit. It Was more practical to simulate seasonal water consumption models of trees with ESR. In further investigations,these models should be optimized.

  11. Comparison of tissue heat balance- and thermal dissipation-derived sap flow measurements in ring-porous oaks and a pine.

    Science.gov (United States)

    Renninger, Heidi J; Schäfer, Karina V R

    2012-01-01

    Sap flow measurements have become integral in many physiological and ecological investigations. A number of methods are used to estimate sap flow rates in trees, but probably the most popular is the thermal dissipation (TD) method because of its affordability, relatively low power consumption, and ease of use. However, there have been questions about the use of this method in ring-porous species and whether individual species and site calibrations are needed. We made concurrent measurements of sap flow rates using TD sensors and the tissue heat balance (THB) method in two oak species (Quercus prinus Willd. and Quercus velutina Lam.) and one pine (Pinus echinata Mill.). We also made concurrent measurements of sap flow rates using both 1 and 2-cm long TD sensors in both oak species. We found that both the TD and THB systems tended to match well in the pine individual, but sap flow rates were underestimated by 2-cm long TD sensors in five individuals of the two ring-porous oak species. Underestimations of 20-35% occurred in Q. prinus even when a "Clearwater" correction was applied to account for the shallowness of the sapwood depth relative to the sensor length and flow rates were underestimated by up to 50% in Q. velutina. Two centimeter long TD sensors also underestimated flow rates compared with 1-cm long sensors in Q. prinus, but only at large flow rates. When 2-cm long sensor data in Q. prinus were scaled using the regression with 1-cm long data, daily flow rates matched well with the rates measured by the THB system. Daily plot level transpiration estimated using TD sap flow rates and scaled 1 cm sensor data averaged about 15% lower than those estimated by the THB method. Therefore, these results suggest that 1-cm long sensors are appropriate in species with shallow sapwood, however more corrections may be necessary in ring-porous species.

  12. Sap flow characteristics of neotropical mangroves in flooded and drained soils

    Science.gov (United States)

    Krauss, Ken W.; Young, P. Joy; Chambers, Jim L.; Doyle, Thomas W.; Twilley, Robert R.

    2007-01-01

    Effects of flooding on water transport in mangroves have previously been investigated in a few studies, most of which were conducted on seedlings in controlled settings. In this study, we used heat-dissipation sap probes to determine if sap flow (Js) attenuates with radial depth into the xylem of mature trees of three south Florida mangrove species growing in Rookery Bay. This was accomplished by inserting sap probes at multiple depths and monitoring diurnal flow. For most species and diameter size class combinations tested, Js decreased dramatically beyond a radial depth of 2 or 4 cm, with little sap flow beyond a depth of 6 cm. Mean Js was reduced on average by 20% in Avicennia germinans (L.) Stearn, Laguncularia racemosa (L.) Gaertn. f. and Rhizophora mangle L. trees when soils were flooded. Species differences were highly significant, with L. racemosahaving the greatest midday Js of about 26g H2O H2O m−2s−1 at a radial depth of 2 cm compared with a mean for the other two species of about 15 g H2O m−2s−1. Sap flow at a depth of 2 cm in mangroves was commensurate with rates reported for other forested wetland tree species. We conclude that: (1) early spring flooding of basin mangrove forests causes reductions in sap flow in mature mangrove trees; (2) the sharp attenuations in Js along the radial profile have implications for understanding whole-tree water use strategies by mangrove forests; and (3) regardless of flood state, individual mangrove tree water use follows leaf-level mechanisms in being conservative.

  13. 树干液流径向分布格局研究进展%Review of advances in radial patterns of stem sap flow

    Institute of Scientific and Technical Information of China (English)

    徐飞; 杨风亭; 王辉民; 戴晓琴

    2012-01-01

    Variability in radial patterns of sap flow is the main source of error in evaluating individual and stand transpiration using thermal techniques. Thus, it is necessary to understand and quantify radial patterns of stem sap flow before accurate estimation of forest transpiration can be conducted. We discuss the methods used to determine radial patterns of sap flow and summarize four main patterns of stem sap flow. We also review the effects of inner structure characteristics and environmental factors on radial patterns of sap flow. In addition, we present the diurnal and seasonal variability in radial patterns of sap flow. Lastly, we propose possible problems in resent research on radial patterns of stem sap flow.%树干液流径向分布的不均匀性是引起热技术估算单株乃至林分蒸腾误差的主要来源.因此,了解树干液流径向分布格局并将其定量化,成为利用热扩散和热脉冲技术准确估算森林蒸腾的必要条件.该文详细介绍了树干液流径向分布格局的研究方法,总结了目前4种常见的树干液流的径向分布格局,分析了影响树干液流径向分布格局的内部结构因素和外部环境因素,阐明了树干液流径向分布格局的时间动态特征及其影响因素,并提出目前研究中存在的问题和可能的解决方法.

  14. CO2 uptake of a mature Acacia mangium plantation estimated from sap flow measurements and stable carbon isotope discrimination

    Science.gov (United States)

    Wang, H.; Zhao, P.; Zou, L. L.; McCarthy, H. R.; Zeng, X. P.; Ni, G. Y.; Rao, X. Q.

    2014-03-01

    A simple, nondestructive method for the estimation of canopy CO2 uptake is important for understanding the CO2 exchange between forest and atmosphere. Canopy CO2 uptake (FCO2) of a subtropical mature A. mangium plantation was estimated by combining sap flow measurements and stable carbon isotope discrimination (Δ) in Southern China from 2004 to 2007. The mechanistic relationship linking FCO2, Δ in leaf sap, and sap flow-based canopy stomatal conductance (Gs) was applied in our study. No significant seasonal variations were observed in Δ or in the ratio of the intercellular and ambient CO2 concentrations (Ci/Ca), although diurnal Ci/Ca varied between sunlit and shaded leaves. A sensitivity analysis showed that estimates of FCO2 were more sensitive to dynamics in Gs than in Ca and Δ. By using seasonally and canopy averaged Ci/Ca values, we obtained an acceptable estimate of FCO2 compared to other estimates. FCO2 exhibited similar diurnal variation to that of Gs. Large seasonal variation in FCO2 was attributed to the responsiveness of Gs to vapor pressure deficit, photosynthetically active radiation, and soil moisture deficit. Our estimate of FCO2 for a mature A. mangium plantation (2.13 ± 0.40 gC m-2 d-1) approached the lower range of values for subtropical mixed forests, probably due to lower mean canopy stomatal conductance, higher Ci/Ca, and greater tree height than other measured forests. Our estimate was also lower than values determined by satellite-based modeling or carbon allocation studies, suggesting the necessity of stand level flux data for verification. Qualitatively, the sap flux/stable isotope results compared well with gas exchange results. Differences in results between the two approaches likely reflected variability due to leaf position and age, which should be reduced for the combined sap flux and isotope technique, as it uses canopy average values of Gs and Ci/Ca.

  15. Time lags between crown and basal sap flows in tropical lianas and co-occurring trees

    NARCIS (Netherlands)

    Chen, Ya Jun; Bongers, Frans; Tomlinson, Kyle; Fan, Ze Xin; Lin, Hua; Zhang, Shu Bin; Zheng, Yu Long; Li, Yang Ping; Cao, Kun Fang; Zhang, Jiao Lin

    2016-01-01

    Water storage in the stems of woody plants contributes to their responses to short-term water shortages. To estimate the contribution of water storage to the daily water budget of trees, time lags of sap flow between different positions of trunk are used as a proxy of stem water storage. In

  16. Evapotranspiration components determined by stable isotope, sap flow and eddy covariance techniques

    NARCIS (Netherlands)

    Williams, D.G.; Cable, W.; Hultine, K.; Hoedjes, J.C.B.; Yepez, E.A.; Simonneaux, V.; Er-Raki, S.; Boulet, G.; Debruin, H.A.R.; Chehbouni, A.; Hartogensis, O.K.; Timouk, F.

    2004-01-01

    Understanding and modeling water exchange in and and semiarid ecosystems is complicated by the very heterogeneous distribution of vegetation and moisture inputs, and the difficulty of measuring and validating component fluxes at a common scale. We combined eddy covariance (EC), sap flow, and stable

  17. The Sap Flow Dynamics and Response of Hedysarum scoparium to Environmental Factors in Semiarid Northwestern China.

    Directory of Open Access Journals (Sweden)

    Jifeng Deng

    Full Text Available Hedysarum scoparium is an important, fast-growing and drought-resistant shrub that has been extensively used for grassland restoration and preventing desertification in semiarid regions of northwestern China. The primary objective of this study was to investigate the diurnal and seasonal variations in stem sap flow (Js and its relation to environmental factors. The stem heat balance method was applied to plants that were approximately 17 years old (with diameters of 25, 16, 13, and 9 mm at ground level and heights of 3.1, 1.8, 1.7 and 1.4 m and growing under natural conditions. The vertical soil temperature profile (ST, soil surface heat flux (SoilG, volumetric soil moisture content (SWC and meteorological variables such as solar radiation (Rn, air temperature (Ta, vapour pressure deficit (VPD, wind speed (Ws relative humidity (RH and precipitation (P were simultaneously measured at a meteorological station on site. Results indicated that Js varied regularly during the diurnal and seasonal term. The nocturnal Js was substantial, with a seasonal variation similar to the patterns of daytime Js. The magnitude of Js changed considerably between sunny and rainy days. Redundancy (RDA and Kendall's tau analysis suggested that daily Js in large plants was more sensitive to environmental factors, and the variation in daily Js during the growing season could be described by a multiple linear regression against environmental variables including Ta, VPD, Ws, RH, ST, and SoilG. While the nocturnal Js in smaller plants was more sensitive to meteorological factors. Ta, VPD, and Ws were significantly correlated with nighttime Js. The hourly nighttime sap flow rate of H. scoparium corresponded closely to Ta and VPD following a non-linear pattern. The results of this study can be used to estimate the transpiration of H. scoparium.

  18. Combining sap flow and eddy covariance approaches to derive stomatal and non-stomatal O{sub 3} fluxes in a forest stand

    Energy Technology Data Exchange (ETDEWEB)

    Nunn, A.J. [Ecophysiology of Plants, Technische Universitaet Muenchen, Am Hochanger 13, D-85354 Freising- Weihenstephan (Germany); Cieslik, S. [Institute for Environment and Sustainability, Joint Research Center, Ispra (Italy); Metzger, U. [Ecophysiology of Plants, Technische Universitaet Muenchen, Am Hochanger 13, D-85354 Freising- Weihenstephan (Germany); Wieser, G. [Federal Research and Training Centre for Forests, Natural Hazards and Landscape, Dept. of Alpine Timberline Ecophysiology, Rennweg 1, A - 6020 Innsbruck (Austria); Matyssek, R., E-mail: matyssek@wzw.tum.d [Ecophysiology of Plants, Technische Universitaet Muenchen, Am Hochanger 13, D-85354 Freising- Weihenstephan (Germany)

    2010-06-15

    Stomatal O{sub 3} fluxes to a mixed beech/spruce stand (Fagus sylvatica/Picea abies) in Central Europe were determined using two different approaches. The sap flow technique yielded the tree-level transpiration, whereas the eddy covariance method provided the stand-level evapotranspiration. Both data were then converted into stomatal ozone fluxes, exemplifying this novel concept for July 2007. Sap flow-based stomatal O{sub 3} flux was 33% of the total O{sub 3} flux, whereas derivation from evapotranspiration rates in combination with the Penman-Monteith algorithm amounted to 47%. In addition to this proportional difference, the sap flow-based assessment yielded lower levels of stomatal O{sub 3} flux and reflected stomatal regulation rather than O{sub 3} exposure, paralleling the daily courses of canopy conductance for water vapor and eddy covariance-based total stand-level O{sub 3} flux. The demonstrated combination of sap flow and eddy covariance approaches supports the development of O{sub 3} risk assessment in forests from O{sub 3} exposure towards flux-based concepts. - Combined tree sap flow and eddy covariance-based methodologies yield stomatal O{sub 3} flux as 33% in total stand flux.

  19. Nocturnal sap flow characteristics and stem water recharge of Acacia mangium

    Institute of Scientific and Technical Information of China (English)

    Hua WANG; Ping ZHAO; Quan WANG; Xian CAI; Ling MA; Xingquan RAO; Xiaoping ZENG

    2008-01-01

    In this paper,we studied the nocturnal stem water recharge of Acacia mangium. It is helpful to improve the precision of canopy transpiration estimation and canopy stomatal conductance, and to further understand the lag time of canopy transpiration to stem sap flow.In this study,the whole-tree sap flow in an A.mangium forest was measured by using Granier's thermal dissipation probe for over two years in the hilly land of South China. The environmental factors, including relative humidity (RH), precipitation, vapor pressure deficit (VPD), photo-synthetically active radiation (PAR),and air temperature (Ta) were recorded simultaneously. The stem water recharge of A. Mangium was analyzed on both daily and monthly scales. Sap flux density was lower at night than during the day. The time range of nighttime sap flux density was longer in the dry season than in the wet season. The water recharging mainly occurred from sunset to midnight.No significant differences were observed among inter-annual nighttime water recharges. Nighttime water recharge had no significant correlation with environmen-tal factors, but was welt correlated with the diameter at breast height, tree height, and crown size. In the dry season the contribution of nighttime water recharge to total transpiration had significant correlations with daytime transpiration, total transpiration, VPD, PAR and Ta, while in the wet season it was significantly correlated with daily transpiration and total transpiration.

  20. Potencials of sap flow evaluation by means of acoustic emission measurements

    Directory of Open Access Journals (Sweden)

    Michal Černý

    2011-01-01

    Full Text Available The work deals with measurement techniques of water conducting system in the trees. Water conducting system (including xylem and phloem indicates its importance for related physiological processes. There are still problems how to measure its functioning (which variables and how, especially in the open field (e.g., forests and orchards in order to get maximum information about it. Simple band dendrometers measuring seasonal dynamics of stem growth have been already applied for many years, being gradually replaced by their more sophisticated electronic versions most recently. The sap flow is a suitable variable, because it links roots and crowns and provide information about transporting the largest amount of mass in plants, which can be decisive for their behavior. Following pioneering work in the last century (Huber, 1932, many types of sap flow measurement methods based on a variety of principles (e.g., thermodynamic, electric, magneto-hydrodynamic, nuclear magnetic resonance, etc. have been described. Only a few of these, particularly those based on thermodynamics, have been widely used in field-grown trees. E.g., heat pulse velocity system developed by Green (1998 and Cohen et al. (1981. Heat ratio method also works with pulses, but interpreted the data in more sophisticated way (Burgess, 2001. Widely used is a simple heat-dissipation method (Granier, 1985. Direct electric heating and internal sensing of temperature was applied in the trunk heat balance method (Čermák et al., 1973, 1976, 1982, 2004; Kučera et al., 1977; Tatarinov et al., 2005. The heat field deformation method is based on measurement of the deformation of the heat field around a needle-like linear heater (Nadezhdina et al., 1998, 2002, 2006; Čermák et al., 2004.Another important variable is water potential, which could be measured in the past only periodically on selected pieces of plant material using pressure (Scholander bomb, but most recently also continuous

  1. Use of the heat dissipation method for sap flow measurement in citrus nursery trees1 Uso do método de dissipação de calor para a medição do fluxo de seiva em mudas cítricas

    Directory of Open Access Journals (Sweden)

    Eduardo Augusto Girardi

    2010-12-01

    Full Text Available Sap flow could be used as physiological parameter to assist irrigation of screen house citrus nursery trees by continuous water consumption estimation. Herein we report a first set of results indicating the potential use of the heat dissipation method for sap flow measurement in containerized citrus nursery trees. 'Valencia' sweet orange [Citrus sinensis (L. Osbeck] budded on 'Rangpur' lime (Citrus limonia Osbeck was evaluated for 30 days during summer. Heat dissipation probes and thermocouple sensors were constructed with low-cost and easily available materials in order to improve accessibility of the method. Sap flow showed high correlation to air temperature inside the screen house. However, errors due to natural thermal gradient and plant tissue injuries affected measurement precision. Transpiration estimated by sap flow measurement was four times higher than gravimetric measurement. Improved micro-probes, adequate method calibration, and non-toxic insulating materials should be further investigated.O fluxo de seiva poderia ser utilizado como parâmetro fisiológico para fomentar a irrigação de mudas cítricas em cultivo protegido pela estimação do consumo contínuo de água. Neste trabalho, reportam-se os primeiros resultados, indicando o uso potencial e as limitações iniciais do método de dissipação de calor para medição do fluxo de seiva em mudas cítricas em recipientes. Mudas de laranjeira-doce 'Valência' [Citrus sinensis (L. Osbeck] enxertadas sobre limoeiro 'Cravo' (Citrus limonia Osbeck foram avaliadas por 30 dias, durante o verão. Sondas de dissipação de calor e sensores do tipo termopar foram construídos a partir de materiais prontamente disponíveis e de baixo custo para favorecer o acesso ao método por viveiristas. O fluxo de seiva apresentou alta correlação com a temperatura do ar dentro da estufa telada. Contudo, erros inerentes ao gradiente térmico natural e a injúrias nos tecidos do caule afetaram a

  2. Clinical flow cytometric screening of SAP and XIAP expression accurately identifies patients with SH2D1A and XIAP/BIRC4 mutations.

    Science.gov (United States)

    Gifford, Carrie E; Weingartner, Elizabeth; Villanueva, Joyce; Johnson, Judith; Zhang, Kejian; Filipovich, Alexandra H; Bleesing, Jack J; Marsh, Rebecca A

    2014-07-01

    X-linked lymphoproliferative disease is caused by mutations in two genes, SH2D1A and XIAP/BIRC4. Flow cytometric methods have been developed to detect the gene products, SAP and XIAP. However, there is no literature describing the accuracy of flow cytometric screening performed in a clinical lab setting. We reviewed the clinical flow cytometric testing results for 656 SAP and 586 XIAP samples tested during a 3-year period. Genetic testing was clinically performed as directed by the managing physician in 137 SAP (21%) and 115 XIAP (20%) samples. We included these samples for analyses of flow cytometric test accuracy. SH2D1A mutations were detected in 15/137 samples. SAP expression was low in 13/15 (sensitivity 87%, CI 61-97%). Of the 122 samples with normal sequencing, SAP was normal in 109 (specificity 89%, CI 82-94%). The positive predictive values (PPVs) and the negative predictive values (NPVs) were 50% and 98%, respectively. XIAP/BIRC4 mutations were detected in 19/115 samples. XIAP expression was low in 18/19 (sensitivity 95%, CI 73-100%). Of the 96 samples with normal sequencing, 59 had normal XIAP expression (specificity 61%, CI 51-71%). The PPVs and NPVs were 33% and 98%, respectively. Receiver-operating characteristic analysis was able to improve the specificity to 75%. Clinical flow cytometric screening tests for SAP and XIAP deficiencies offer good sensitivity and specificity for detecting genetic mutations, and are characterized by high NPVs. We recommend these tests for patients suspected of having X-linked lymphoproliferative disease type 1 (XLP1) or XLP2. © 2014 Clinical Cytometry Society.

  3. Relationships between SAP-flow measurements, whole-canopy transpiration and reference evapotranspiration in field-grown papaya (Carica papaya L.)

    Science.gov (United States)

    Whole-canopy gas exchange measurement in papaya can provide a scientific basis to optimize irrigation, and fruit yield and quality. The objectives of this study were to: 1) verify the relationship between xylem sap flow measured by the heat coefficient method and whole canopy transpiration in ‘Gra...

  4. Partition of nocturnal sap flow in Acacia mangium and its implication for estimating the whole-tree transpiration

    Institute of Scientific and Technical Information of China (English)

    Hua WANG; Ping ZHAO; Xian CAI; Ling MA; Xingquan RAO; Xiaoping ZENG; Quan WANG

    2009-01-01

    We analyzed the partition of nocturnal sap flow into refilling of internal water storage and transpiration in Acacia mangium. Sap flow of trees was monitored continuously with Granier's sensors for estimating the whole-tree transpiration. Possible night transpiration and stomatal conductance at the leaf level in the canopy were measured with a LI-6400 photosynthesis measuring system. For nocturnal leaf transpiration and stomatal conductance were weak, nocturnal sap flow of mature A. mangium trees was mainly associated with water recharge in the trunk. No significant change in night water recharge of the trunk was found at both seasonal and inter-annual scales. Morphological features of trees including diameter at the breast height (DBH), tree height, and canopy size could explain variances of night water recharge. Furthermore, although the contribution of nocturnal sap flow to the total transpiration varied among seasons and DBH classes, the error caused by night water recharge on whole-tree transpiration was negligible.

  5. Impact of Laurel Wilt, Caused by Raffaelea lauricola, on Leaf Gas Exchange and Xylem Sap Flow in Avocado, Persea americana.

    Science.gov (United States)

    Ploetz, Randy C; Schaffer, Bruce; Vargas, Ana I; Konkol, Joshua L; Salvatierra, Juanpablo; Wideman, Ronney

    2015-04-01

    Laurel wilt, caused by Raffaelea lauricola, is a destructive disease of avocado (Persea americana). The susceptibility of different cultivars and races was examined previously but more information is needed on how this host responds to the disease. In the present study, net CO2 assimilation (A), stomatal conductance of H2O (gs), transpiration (E), water use efficiency (WUE), and xylem sap flow rates were assessed in cultivars that differed in susceptibility. After artificial inoculation with R. lauricola, there was a close relationship between symptom development and reductions in A, gs, E, WUE, and mean daily sap flow in the most susceptible cultivar, 'Russell', and significantly greater disease and lower A, gs, E, WUE, and sap flow rates were usually detected after 15 days compared with the more tolerant 'Brogdon' and 'Marcus Pumpkin'. Significant differences in preinoculation A, gs, E, and WUE were generally not detected among the cultivars but preinoculation sap flow rates were greater in Russell than in Brogdon and Marcus Pumpkin. Preinoculation sap flow rates and symptom severity for individual trees were correlated at the end of an experiment (r=0.46), indicating that a plant's susceptibility to laurel wilt was related to its ability to conduct water. The potential management of this disease with clonal rootstocks that reduce sap flow rates is discussed.

  6. Sap flow in response to rainfall pulses for two shrub species in the semiarid Chinese Loess Plateau

    Directory of Open Access Journals (Sweden)

    Jian Shengqi

    2016-06-01

    Full Text Available Rainfall pulses can significantly drive the evolution of the structure and function of semiarid ecosystems, and understanding the mechanisms that underlie the response of semiarid plants to rainfall is the key to understanding the responses of semi–arid ecosystems to global climatic change. We measured sap flow in the branches and stems of shrubs (Caragana korshinskii Kom. and Hippophae rhamnoides Linn. using sap flow gauges, and studied the response of sap flow density to rainfall pulses using the “threshold–delay” model in the Chinese Loess Plateau. The results showed that the sap flow began about 1 h earlier, and increased twofold after rainfall, compared to its pre-rainfall value. The sap flow increased significantly with increasing rainfall classes, then gradually decreased. The response of sap flow was different among rainfall, species, position (branch and stem during the pulse period, and the interactive effects also differed significantly (P < 0.0001. The response pattern followed the threshold–delay model, with lower rainfall thresholds of 5.2, 5.5 mm and 0.7, 0.8 mm of stem and branch for C. korshinskii and H. rhamnoides, demonstrating the importance of small rainfall events for plant growth and survival in semi–arid regions.

  7. Sap Flow of Populus euphratica in a Desert Riparian Forest in an Extreme Arid Region During the Growing Season

    Institute of Scientific and Technical Information of China (English)

    Jian-Hua Si; Qi Feng; Xiao-You Zhang; Zong-Qiang Chang; Yong-Hong Su; Hai-Yang Xi

    2007-01-01

    In the present study, the heat pulse technique was applied to investigate the stem sap flow of Populus euphratica in a desert riparian forest in an extreme arid region from April to October 2003 and from May to October 2004. The experimental sites were in Qidaoqiao (101 °10'E, 41°59'N) and Bayantaolai farm (101°14'E, 42°01'N) in Ejina county, in the Iow reaches of the Heihe River, China. The results indicated that the diurnal change in the velocity of sap flow showed minor fluctuations. At night, the rising of sap flow could be observed in the main tree species because of root pressure. During the growing season, the maximum average velocity was observed in July, followed by August, and the same velocity was observed in September and May; the minimum velocity was observed in October. The transpiration from June to August during the growing season accounted for approximately 70% of the annual total transpiration. The sap flow velocity of P. euphratica trees of different ages could be arranged in the order: 15 yr > 25 yr > 50 yr. Sap flow velocity was closely related to changes in micrometeorological factors, with average sap flow velocity showing a significant linear correlation with net radiation, air temperature and relative humidity.

  8. Heat dissipation sensors of variable length for the measurement of sap flow in trees with deep sapwood.

    Science.gov (United States)

    James, Shelley A; Clearwater, Michael J; Meinzer, Frederick C; Goldstein, Guillermo

    2002-03-01

    Robust thermal dissipation sensors of variable length (3 to 30 cm) were developed to overcome limitations to the measurement of radial profiles of sap flow in large-diameter tropical trees with deep sapwood. The effective measuring length of the custom-made sensors was reduced to 1 cm at the tip of a thermally nonconducting shaft, thereby minimizing the influence of nonuniform sap flux density profiles across the sapwood. Sap flow was measured at different depths and circumferential positions in the trunks of four trees at the Parque Natural Metropolitano canopy crane site, Panama City, Republic of Panama. Sap flow was detected to a depth of 24 cm in the trunks of a 1-m-diameter Anacardium excelsum (Bertero & Balb. ex Kunth) Skeels tree and a 0.65-m-diameter Ficus insipida Willd. tree, and to depths of 7 cm in a 0.34-m-diameter Cordia alliodora (Ruiz & Pav.) Cham. trunk, and 17 cm in a 0.47-m-diameter Schefflera morototoni (Aubl.) Maguire, Steyerm. & Frodin trunk. Sap flux density was maximal in the outermost 4 cm of sapwood and declined with increasing sapwood depth. Considerable variation in sap flux density profiles was observed both within and among the trees. In S. morototoni, radial variation in sap flux density was associated with radial variation in wood properties, particularly vessel lumen area and distribution. High variability in radial and circumferential sap flux density resulted in large errors when measurements of sap flow at a single depth, or a single radial profile, were used to estimate whole-plant water use. Diurnal water use ranged from 750 kg H2O day-1 for A. excelsum to 37 kg H2O day-1 for C. alliodora.

  9. Measured Sap Flow and Estimated Evapotranspiration of Tropical Eucalyptus urophylla Plantations in South China

    Institute of Scientific and Technical Information of China (English)

    ZHOUGuo-Yi; YINGuang-Cai; JimMORRIS; BAIJia-Yu; CHENShao-Xiong; CHUGuo-Wei; ZHANGNing-Nan

    2004-01-01

    During the period of September 12, 1999 to September 24, 2000, we measured sap flow ofeucalyptus (Euca/yptus urophylla S.T. Blake) plantations using heat pulse technique, and the relevantenvironmental vaiables, such as soil evaporation and canopy interception, etc, at Hetou and Jijia sites,Leizhou Peninsula, Guangdong Province. Based on the measurements of sap flow and estimates ofevapotranspiration, the following can be concluded: (1) the maximum of diurnal xylem sap flux density (SFD)at Hetou, where covered with coarse-textured soils formed on Quaternary sediments, was almost twice ofthat at Jijia, where located on clay-rich soils derived from basalt; (2) SFD was highly correlated to watervapor pressure deficit (VPD) of ambient air near the canopy layer, (3) the correlation between SFD and airtemperature also depends on soil properties and soil water potential; (4) the relative differences betweenmeasured and modeled evapotranspiration were small, being 5.26% at Hetou and 6.14% at Jijia; (5) theplantation transpiration accounted for 62.2% and 51.3% of the evapotranspiration at Hetou and Jijia,respectively; and (6) the averaged SFD per unit leaf area (ASPULA) was a good index to estimate theamount of water consumption of tree species.

  10. Response of sap flow to environmental factors in the headwater catchment of Miyun Reservoir in subhumid North China

    Science.gov (United States)

    Tie, Qiang; Hu, Hongchang; Tian, Fuqiang; Liu, Yaping; Xu, Ran

    2015-04-01

    Since the headwater catchment of Miyun Reservoir is the main drinking water conservation area of Beijing, its water cycle is of importance for the regional water resource. Transpiration is an important component of water cycle, which can be estimated by sap flow. In this study, the dynamics of sap flow and its response to environmental factors and relationship with leaf area index (LAI) were analyzed. The field study was conducted in the Xitaizi Experimental Catchment, located in the headwater catchment of Miyun Reservoir in subhumid North China. The Aspen (Populus davidiana) and Epinette (Larix gmelinii) are the two dominant tree species. Sap flow in 15 Aspen (Populus davidiana) trees was monitored using thermal dissipation probes (TDP) during the growing season of 2013 and 2014, and sap flow in another 3 Epinette (Larix gmelinii) trees was also monitored during September and October in 2014 for comparative analysis. Physiological and biometric parameters of the selected trees and the environmental factors, including meteorological variables, soil moisture content and groundwater table depth were measured. Vapor pressure deficit (VPD), variable of transpiration (VT) and reference crop evapotranspiration (ET0) were calculated using the measured environmental factors. The LAI, which is used to characterize phenophase, was calculated using the Moderate Resolution Imaging Spectroradiometer (MODIS) LAI product (MCD15A3). Correlation analysis for daily sap flow and air temperature, relative humidity, precipitation, wind speed, solar radiation, VPD, VT and ET0 under different soil moisture and groundwater table depth conditions was performed. Diurnal course and hysteresis of sap flow were analyzed as a function of air temperature, solar radiation, VPD and VT on the typical sunny, cloudy and rainy days under different soil moisture conditions. Correlation analysis between daily sap flow and LAI showed that LAI and phenophase significantly influence sap flow and restrict

  11. A simple, novel and high efficiency sap inoculation method to screen for tobacco streak virus.

    Science.gov (United States)

    Sundaresha, S; Sreevathsa, Rohini; Balol, Gurupada B; Keshavareddy, G; Rangaswamy, K T; Udayakumar, M

    2012-10-01

    A rapid and efficient sap inoculation method for tobacco streak virus (TSV) was developed in sunflower. Sap from TSV-infected sunflower plants was freshly extracted in phosphate buffer and diluted serially from 10(-1) to 10(-8). Two-day old seedlings of sunflower were injured at the meristem and immersed in the sap for 10 min, maintained at 20 °C for 2-3 days and shifted to greenhouse. The surviving seedlings in the respective sap dilution were scored for symptoms of sunflower necrosis disease (SND). SND symptoms were seen in 80 % of the seedlings inoculated with a sap dilution of 10(-5). ELISA and RT-PCR analysis of coat protein and movement protein of TSV confirmed SND symptoms. The methodology was also found to be reproducible when the sap from the infected plants was inoculated onto healthy plants. The main aim of the study was to develop a primary screening strategy for the selection of transgenics developed for SND resistance. This methodology can also be extended for the analysis of resistance against other viruses.

  12. Sapfluxnet: a global database of sap flow measurements to unravel the ecological factors of transpiration regulation in woody plants

    Science.gov (United States)

    Poyatos, Rafael; Martínez-Vilalta, Jordi; Molowny-Horas, Roberto; Steppe, Kathy; Oren, Ram; Katul, Gabriel; Mahecha, Miguel

    2016-04-01

    Plant transpiration is one of the main components of the global water cycle, it controls land energy balance, determines catchment hydrological responses and exerts strong feedbacks on regional and global climate. At the same time, plant productivity, growth and survival are severely constrained by water availability, which is expected to decline in many areas of the world because of global-change driven increases in drought conditions. While global surveys of drought tolerance traits at the organ level are rapidly increasing our knowledge of the diversity in plant functional strategies to cope with drought stress, a whole-plant perspective of drought vulnerability is still lacking. Sap flow measurements using thermal methods have now been applied to measure seasonal patterns in water use and the response of transpiration to environmental drivers across hundreds of species of woody plants worldwide, covering a wide range of climates, soils and stand structural characteristics. Here, we present the first effort to build a global database of sub-daily, tree-level sap flow (SAPFLUXNET) that will be used to improve our understanding of physiological and structural determinants of plant transpiration and to further investigate the role of vegetation in controlling global water balance. We already have the expression of interest of data contributors representing >115 globally distributed sites, > 185 species and > 700 trees, measured over at least one growing season. However, the potential number of available sites and species is probably much higher given that > 2500 sap flow-related papers have been identified in a Scopus literature search conducted in November 2015. We will give an overview of how data collection, harmonisation and quality control procedures are implemented within the project. We will also discuss potential analytical strategies to synthesize hydroclimatic controls on sap flow into biologically meaningful traits related to whole-plant transpiration

  13. Comparison of ecosystem water flux measured with the Eddy covariance- and the direct xylem sap flux method in a mountainous forest

    Energy Technology Data Exchange (ETDEWEB)

    Stefanicki, G.; Geissbuehler, P.; Siegwolf, R. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1999-08-01

    The Eddy covariance technique allows to measure different components of turbulent air fluxes, including the flow of water vapour. Sap flux measurements determine directly the water flow in tree stems. We compared the water flux just above the crowns of trees in a forest by the technique of Eddy covariance and the water flux by the xylem sap flux method. These two completely different approaches showed a good qualitative correspondence. The correlation coefficient is 0.8. With an estimation of the crown diameter of the measured tree we also find a very good quantitative agreement. (author) 3 figs., 5 refs.

  14. Assessing the thermal dissipation sap flux density method for monitoring cold season water transport in seasonally snow-covered forests.

    Science.gov (United States)

    Chan, Allison M; Bowling, David R; Phillips, Nathan

    2017-07-01

    Productivity of conifers in seasonally snow-covered forests is high before and during snowmelt when environmental conditions are optimal for photosynthesis. Climate change is altering the timing of spring in many locations, and changes in the date of transition from winter dormancy can have large impacts on annual productivity. Sap flow methods provide a promising approach to monitor tree activity during the cold season and the winter-spring and fall-winter transitions. Although sap flow techniques have been widely used, cold season results are generally not reported. Here we examine the feasibility of using the Granier thermal dissipation (TD) sap flux density method to monitor transpiration and dormancy of evergreen conifers during the cold season. We conducted a laboratory experiment which demonstrated that the TD method reliably detects xylem water transport (when it occurs) both at near freezing temperature and at low flow rate, and that the sensors can withstand repeated freeze-thaw events. However, the dependence between sensor output and water transport rate in these experiments differed from the established TD relation. In field experiments, sensors installed in two Abies forests lasted through two winters and a summer with low failure. The baseline (no-flow) sensor output varied considerably with temperature during the cold season, and a new baseline algorithm was developed to accommodate this variation. The Abies forests differed in elevation (2070 and 2620 m), and there was a clear difference in timing of initiation and cessation of transpiration between them. We conclude that the TD method can be reliably used to examine water transport during cold periods with associated low flow conditions. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  15. Estimates of evapotranspiration for riparian sites (Eucalyptus) in the Lower Murray -Darling Basin using ground validated sap flow and vegetation index scaling techniques

    Science.gov (United States)

    Doody, T.; Nagler, P. L.; Glenn, E. P.

    2014-12-01

    Water accounting is becoming critical globally, and balancing consumptive water demands with environmental water requirements is especially difficult in in arid and semi-arid regions. Within the Murray-Darling Basin (MDB) in Australia, riparian water use has not been assessed across broad scales. This study therefore aimed to apply and validate an existing U.S. riparian ecosystem evapotranspiration (ET) algorithm for the MDB river systems to assist water resource managers to quantify environmental water needs over wide ranges of niche conditions. Ground-based sap flow ET was correlated with remotely sensed predictions of ET, to provide a method to scale annual rates of water consumption by riparian vegetation over entire irrigation districts. Sap flux was measured at nine locations on the Murrumbidgee River between July 2011 and June 2012. Remotely sensed ET was calculated using a combination of local meteorological estimates of potential ET (ETo) and rainfall and MODIS Enhanced Vegetation Index (EVI) from selected 250 m resolution pixels. The sap flow data correlated well with MODIS EVI. Sap flow ranged from 0.81 mm/day to 3.60 mm/day and corresponded to a MODIS-based ET range of 1.43 mm/day to 2.42 mm/day. We found that mean ET across sites could be predicted by EVI-ETo methods with a standard error of about 20% across sites, but that ET at any given site could vary much more due to differences in aquifer and soil properties among sites. Water use was within range of that expected. We conclude that our algorithm developed for US arid land crops and riparian plants is applicable to this region of Australia. Future work includes the development of an adjusted algorithm using these sap flow validated results.

  16. A noninvasive optical system for the measurement of xylem and phloem sap flow in woody plants of small stem size.

    Science.gov (United States)

    Helfter, Carole; Shephard, Jonathon D; Martinez-Vilalta, Jordi; Mencuccini, Maurizio; Hand, Duncan P

    2007-02-01

    Over the past 70 years, heat has been widely used as a tracer for estimating the flow of water in woody and herbaceous plants. However, most commercially available techniques for monitoring whole plant water use are invasive and the measurements are potentially flawed because of wounding of the xylem tissue. The study of photosynthate transport in the phloem remains in its infancy, and little information about phloem transport rates is available owing to the fragility of the vascular tissue. The aim of our study was to develop a compact, stand-alone non-invasive system allowing for direct detection of phloem and xylem sap movement. The proposed method uses a heat pulse as a tracer for sap flow. Heat is applied to the surface of the stem with a near-infrared laser source, and heat propagation is monitored externally by means of an infrared camera. Heat pulse velocities are determined from the thermometric data and related to the more useful quantity, mass flow rate. Simulation experiments on the xylem tissue of severed silver birch (Betula pendula Roth.) branch segments were performed to assess the feasibility of the proposed approach, highlight the characteristics of the technique and outline calibration strategies. Good agreement between imposed and measured flow rates was achieved leading to experimentation with live silver birch and oak (Quercus robur L.) saplings. It was demonstrated that water flow through xylem vessels can be monitored non-invasively on an intact stem with satisfactory accuracy despite simultaneous sugar transport in the phloem. In addition, it was demonstrated that the technique allows for unequivocal detection of phloem flow velocities.

  17. [Time lag characteristics of stem sap flow of common tree species during their growth season in Beijing downtown].

    Science.gov (United States)

    Wang, Hua; Ouyang, Zhi-yun; Zheng, Hua; Wang, Xiao-ke; Ni, Yong-ming; Ren, Yu-fen

    2009-09-01

    From April to September in 2008, the stem sap flow velocity (Js) of several common tree species (Ginkgo biloba, Aesculus chinensis, Magnolia denudata, Robinia pseudoacacia, Pinus tabulaeformis and Cedrus deodara) in Beijing was measured by thermal dissipation method. Crosscorrelation analysis was used to estimate the time lag between the stem sap flow and the driving factors of canopy transpiration among the tree species. The Js of the six tree species was significantly correlated with the total radiation (Rs) and vapor pressure deficit (D), and the Js was lagged behind Rs but ahead of D. The maximum correlation coefficient of Js with Rs (0.74-0.93) was often higher than that of Js with D (0.57-0.79), indicating that the diurnal Js was more dependent on Rs than on D. The sampled tree species except P. tabulaeformis had a shorter time lag of Js with Rs (10-70 min) than with D (47-130 min), and there existed significant differences among R. pseudoacacia, P. tabulaeformis, and C. deodara. The time lag between the Js and the driving factors of canopy transpiration was mainly correlated with the tree features (DBH, tree height, canopy area, and sapwood area) and the nocturnal water recharge, regardless of tree species.

  18. [Time lag effect between stem sap flow and photosynthetically active radiation, vapor pressure deficit of Acacia mangium].

    Science.gov (United States)

    Wang, Hua; Zhao, Ping; Cai, Xi-An; Ma, Ling; Rao, Xing-Quan; Zeng, Xiao-Ping

    2008-02-01

    Based on the measurement of the stem sap flow of Acacia mangium with Granier' s thermal dissipation probe, and the cross-correlation and time serial analysis of the sap flow and corresponding photosynthetically active radiation and vapor pressure deficit, this paper studied the time lag effect between the stem sap flow of A. mangium and the driving factors of the tree canopy transpiration. The results indicated that the main driving factors of the transpiration were photosynthetically active radiation (PAR) and vapor pressure deficit (VPD). Sap flux density (Js) was more dependent on PAR than on VPD, and the dependence was more significant in dry season than in wet season. Sap flow lagged behind PAR but advanced than VPD in both dry and wet seasons. The time lag did not show any significant variation across different size tree individuals, but showed significant variation in different seasons. Time lag effect was not correlated with tree height, diameter at the breast, and canopy size. The time lag between Js and VPD was significantly related to nighttime water recharge in dry season, but reversed in wet season.

  19. 0.7 and 3 T MRI and sap flow in intact trees: xylem and phloem in action

    NARCIS (Netherlands)

    Homan, N.; Windt, C.W.; Vergeldt, F.J.; Gerkema, E.; As, van H.

    2007-01-01

    Dedicated magnetic resonance imaging (MRI) hardware is described that allows imaging of sap flow in intact trees with a maximal trunk diameter of 4 cm and height of several meters. This setup is used to investigate xylem and phloem flow in an intact tree quantitatively. Due to the fragile gradients

  20. 0.7 and 3 T MRI and sap flow in intact trees: xylem and phloem in action

    NARCIS (Netherlands)

    Homan, N.; Windt, C.W.; Vergeldt, F.J.; Gerkema, E.; As, van H.

    2007-01-01

    Dedicated magnetic resonance imaging (MRI) hardware is described that allows imaging of sap flow in intact trees with a maximal trunk diameter of 4 cm and height of several meters. This setup is used to investigate xylem and phloem flow in an intact tree quantitatively. Due to the fragile gradients

  1. Use of sap flow measurements to validate stomatal functions for mature beech (Fagus sylvatica) in view of ozone uptake calculations.

    Science.gov (United States)

    Braun, Sabine; Schindler, Christian; Leuzinger, Sebastian

    2010-09-01

    For a quantitative estimate of the ozone effect on vegetation reliable models for ozone uptake through the stomata are needed. Because of the analogy of ozone uptake and transpiration it is possible to utilize measurements of water loss such as sap flow for quantification of ozone uptake. This technique was applied in three beech (Fagus sylvatica) stands in Switzerland. A canopy conductance was calculated from sap flow velocity and normalized to values between 0 and 1. It represents mainly stomatal conductance as the boundary layer resistance in forests is usually small. Based on this relative conductance, stomatal functions to describe the dependence on light, temperature, vapour pressure deficit and soil moisture were derived using multivariate nonlinear regression. These functions were validated by comparison with conductance values directly estimated from sap flow. The results corroborate the current flux parameterization for beech used in the DO3SE model.

  2. Explaining spatial patterns of sap flow: day-to-day shifts in relevance of site- and tree-specific controls

    Science.gov (United States)

    Hassler, Sibylle K.; Weiler, Markus; Blume, Theresa

    2015-04-01

    Transpiration is a key process in the hydrological cycle and a sound understanding and quantification of transpiration is essential for management decisions and for hydrological and climatological modelling. To assess transpiration at the tree scale sap flow velocity is commonly measured. Besides atmospheric conditions and soil moisture state, tree-specific characteristics such as species, size or social status control sap flow of individual trees. Within forest stands, properties such as species composition, basal area or stem number also affect sap flow via competition or facilitation mechanisms. Finally, sap flow patterns might also be influenced by landscape-scale characteristics such as geology, slope position or aspect because they affect water and energy availability; however, so far little is known about these larger-scale controls. We studied the relative importance of various tree- and site-specific characteristics with linear statistical models for daily sap velocity observations on 38 trees at 12 locations in mixed beech and oak forests in a catchment in Luxemburg. The temporal variation of the predictors' importance for sap velocity patterns was then related to hydro-meteorological conditions. Results indicate that a combination of tree- and site-specific controls influence sap velocity patterns, namely tree species, tree diameter, stand basal area, geology and aspect. The temporal dynamics of these controls are related to hydro-meteorological conditions, with tree-specific controls dominating when the atmospheric gradient is strong, i.e. the vapour pressure deficit is large, leading to higher sap velocities, whereas landscape-scale site characteristics are more important during weak atmospheric gradients. The importance of individual predictors also varies between spring and summer, probably due to different soil moisture and atmospheric conditions of the two periods. We conclude that both tree- and site-specific characteristics control sap velocity

  3. The annual pattern of sap flow in tow Eucalyptus species established in the vicinity of gold-mine tailings dams in central South Africa

    CSIR Research Space (South Africa)

    Dye, P

    2016-08-01

    Full Text Available of contaminants. The annual pattern of hourly sap flow in four contiguous Eucalyptus dunnii trees (aged three years) was followed over a full year in a species trial situated near Carltonville. The annual pattern of hourly sap flow was also recorded in four...

  4. What the towers don't see at night: nocturnal sap flow in trees and shrubs at two AmeriFlux sites in California.

    Science.gov (United States)

    Fisher, Joshua B; Baldocchi, Dennis D; Misson, Laurent; Dawson, Todd E; Goldstein, Allen H

    2007-04-01

    At the leaf scale, it is a long-held assumption that stomata close at night in the absence of light, causing transpiration to decrease to zero. Energy balance models and evapotranspiration equations often rely on net radiation as an upper bound, and some models reduce evapotranspiration to zero at night when there is no solar radiation. Emerging research is showing, however, that transpiration can occur throughout the night in a variety of vegetation types and biomes. At the ecosystem scale, eddy covariance measurements have provided extensive data on latent heat flux for a multitude of ecosystem types globally. Nighttime eddy covariance measurements, however, are generally unreliable because of low turbulence. If significant nighttime water loss occurs, eddy flux towers may be missing key information on latent heat flux. We installed and measured rates of sap flow by the heat ratio method (Burgess et al. 2001) at two AmeriFlux (part of FLUXNET) sites in California. The heat ratio method allows measurement and quantification of low rates of sap flow, including negative rates (i.e., hydraulic lift). We measured sap flow in five Pinus ponderosa Dougl. ex Laws. trees and three Arctostaphylos manzanita Parry and two Ceanothus cordulatus A. Kellog shrubs in the Sierra Nevada Mountains, and in five Quercus douglasii Hook and Arn. trees at an oak savanna in the Central Valley of California. Nocturnal sap flow was observed in all species, and significant nighttime water loss was observed in both species of trees. Vapor pressure deficit and air temperature were both well correlated with nighttime transpiration; the influence of wind speed on nighttime transpiration was insignificant at both sites. We distinguished between storage-tissue refilling and water loss based on data from Year 2005, and calculated the percentage by which nighttime transpiration was underestimated by eddy covariance measurements at both sites.

  5. Reconstruction of the past flow channels in the early Holocene at Lake Tonle Sap, Cambodia

    Science.gov (United States)

    Haraguchi, T.; Yonenobu, H.; Tokunaga, T.; Shimoda, I.

    2013-05-01

    Lake Tonle Sap is located at the central part of Cambodia, South-East Asia. In rainy season, the water body swells with the water depth accordingly increasing from 1 up to 10 meters due to a pulsive intrusion from the Mekong River. The lake is therefore a vital reservoir that protects the region from flooding. It is paleolimnologically important to better understand how the lake has gained the function controlling water balance of this region. We undertook an extensive echo-sounding exploration at the lake in order to clarify the subsurface structure of Lake Tonle Sap. The survey was conducted in rainy seasons from 2009 to 2012. Sediment cores were collected at three sites at the middle part of the lake. Echo sounding was undertaken over the whole part of the lake using a single-channel sub-bottom profiling system (Stratabox, SyQwest Inc.). A prominent sound frequency of 10 KHz was selected in order to observe structure of reflectance planes up to the 40-m depth. In consequence, we discovered deposited valleys forming a complex network of past flow channels. The subsurface structure of the lake bed was mostly complacent showing a strongly reflecting plane observed at the depth of 1-2 meters; the sediments mainly consisted of mud. A number of valley-shaped reflecting planes were observed at the depth of 10-14 meters. Radiocarbon dates of carbonaceous materials collected at the vally bottom were around 10 ka calBP. A 3-D reconstruction presented a complex network of deposited flow channels.

  6. Time lags between crown and basal sap flows in tropical lianas and co-occurring trees.

    Science.gov (United States)

    Chen, Ya-Jun; Bongers, Frans; Tomlinson, Kyle; Fan, Ze-Xin; Lin, Hua; Zhang, Shu-Bin; Zheng, Yu-Long; Li, Yang-Ping; Cao, Kun-Fang; Zhang, Jiao-Lin

    2016-06-01

    Water storage in the stems of woody plants contributes to their responses to short-term water shortages. To estimate the contribution of water storage to the daily water budget of trees, time lags of sap flow between different positions of trunk are used as a proxy of stem water storage. In lianas, another large group of woody species, it has rarely been studied whether stored water functions in their daily water use, despite their increasing roles in the carbon and water dynamics of tropical forests caused by their increasing abundance. We hypothesized that lianas would exhibit large time lags due to their extremely long stems, wide vessels and large volume of parenchyma in the stem. We examined time lags in sap flow, diel changes of stem volumetric water content (VWC) and biophysical properties of sapwood of 19 lianas and 26 co-occurring trees from 27 species in 4 forests (karst, tropical seasonal, flood plain and savanna) during a wet season. The plants varied in height/length from 60 m. The results showed that lianas had significantly higher saturated water content (SWC) and much lower wood density than trees. Seven of 19 liana individuals had no time lags; in contrast, only 3 of 26 tree individuals had no time lags. In general, lianas had shorter time lags than trees in our data set, but this difference was not significant for our most conservative analyses. Across trees and lianas, time lag duration increased with diurnal maximum changeable VWC but was independent of the body size, path length, wood density and SWC. The results suggest that in most lianas, internal stem water storage contributes little to daily water budget, while trees may rely more on stored water in the stem. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  7. Sap flow in Searsia pendulina and Searsia lancea trees established on gold mining sites in central South Africa

    CSIR Research Space (South Africa)

    Dye, P

    2017-03-01

    Full Text Available of the heat pulse velocity technique. Plot sap flow was estimated by scaling up according to the number and size of stems, and utilizing functions relating leaf dry mass and leaf area to stem diameter. The deciduous species S. pendulina was found to use 591 mm...

  8. Assessment of actual transpiration rate in olive tree field combining sap-flow, leaf area index and scintillometer measurements

    Science.gov (United States)

    Agnese, C.; Cammalleri, C.; Ciraolo, G.; Minacapilli, M.; Provenzano, G.; Rallo, G.; de Bruin, H. A. R.

    2009-09-01

    Models to estimate the actual evapotranspiration (ET) in sparse vegetation area can be fundamental for agricultural water managements, especially when water availability is a limiting factor. Models validation must be carried out by considering in situ measurements referred to the field scale, which is the relevant scale of the modelled variables. Moreover, a particular relevance assumes to consider separately the components of plant transpiration (T) and soil evaporation (E), because only the first is actually related to the crop stress conditions. Objective of the paper was to assess a procedure aimed to estimate olive trees actual transpiration by combining sap flow measurements with the scintillometer technique at field scale. The study area, located in Western Sicily (Italy), is mainly cultivated with olive crop and is characterized by typical Mediterranean semi-arid climate. Measurements of sap flow and crop actual evapotranspiration rate were carried out during 2008 irrigation season. Crop transpiration fluxes, measured on some plants by means of sap flow sensors, were upscaled considering the leaf area index (LAI). The comparison between evapotranspiration values, derived by displaced-beam small-aperture scintillometer (DBSAS-SLS20, Scintec AG), with the transpiration fluxes obtained by the sap flow sensors, also allowed to evaluate the contribute of soil evaporation in an area characterized by low vegetation coverage.

  9. [Complexity and its integrative effects of the time lags of environment factors affecting Larix gmelinii stem sap flow].

    Science.gov (United States)

    Wang, Hui-Mei; Sun, Wei; Zu, Yuan-Gang; Wang, Wen-Jie

    2011-12-01

    Based on the one-year (2005) observations with a frequency of half hour on the stem sap flow of Larix gmelinii plantation trees planted in 1969 and the related environmental factors air humidity (RH), air temperature (T(air)), photosynthetic components active radiation (PAR), soil temperature (T(soil)), and soil moisture (TDR), principal analysis (PCA) and correction analysis were made on the time lag effect of the stem flow in different seasons (26 days of each season) and in a year via dislocation analysis, with the complexity and its integrative effects of the time lags of environment factors affecting the stem sap flow approached. The results showed that in different seasons and for different environmental factors, the time lag effect varied obviously. In general, the time lag of PAR was 0.5-1 hour ahead of sap flow, that of T(air) and RH was 0-2 hours ahead of or behind the sap flow, and the time lags of T(soil) and TDR were much longer or sometimes undetectable. Because of the complexity of the time lags, no evident improvements were observed in the linear correlations (R2, slope, and intercept) when the time lags based on short-term (20 days) data were used to correct the time lags based on whole year data. However, obvious improvements were found in the standardized and non-standardized correlation coefficients in stepwise multiple regressions, i.e., the time lag corrections could improve the effects of RH, but decreased the effects of PAR, T(air), and T(soil). PCA could be used to simplify the complexity. The first and the second principal components could stand for over 75% information of all the environmental factors in different seasons and in whole year. The time lags of both the first and the second principal components were 1-1.5 hours in advance of the sap flow, except in winter (no time lag effect).

  10. Determining Accuracy of Thermal Dissipation Methods-based Sap Flux in Japanese Cedar Trees

    Science.gov (United States)

    Su, Man-Ping; Shinohara, Yoshinori; Laplace, Sophie; Lin, Song-Jin; Kume, Tomonori

    2017-04-01

    Thermal dissipation method, one kind of sap flux measurement method that can estimate individual tree transpiration, have been widely used because of its low cost and uncomplicated operation. Although thermal dissipation method is widespread, the accuracy of this method is doubted recently because some tree species materials in previous studies were not suitable for its empirical formula from Granier due to difference of wood characteristics. In Taiwan, Cryptomeria japonica (Japanese cedar) is one of the dominant species in mountainous area, quantifying the transpiration of Japanese cedar trees is indispensable to understand water cycling there. However, no one have tested the accuracy of thermal dissipation methods-based sap flux for Japanese cedar trees in Taiwan. Thus, in this study we conducted calibration experiment using twelve Japanese cedar stem segments from six trees to investigate the accuracy of thermal dissipation methods-based sap flux in Japanese cedar trees in Taiwan. By pumping water from segment bottom to top and inserting probes into segments to collect data simultaneously, we compared sap flux densities calculated from real water uptakes (Fd_actual) and empirical formula (Fd_Granier). Exact sapwood area and sapwood depth of each sample were obtained from dying segment with safranin stain solution. Our results showed that Fd_Granier underestimated 39 % of Fd_actual across sap flux densities ranging from 10 to 150 (cm3m-2s-1); while applying sapwood depth corrected formula from Clearwater, Fd_Granier became accurately that only underestimated 0.01 % of Fd_actual. However, when sap flux densities ranging from 10 to 50 (cm3m-2s-1)which is similar with the field data of Japanese cedar trees in a mountainous area of Taiwan, Fd_Granier underestimated 51 % of Fd_actual, and underestimated 26 % with applying Clearwater sapwood depth corrected formula. These results suggested sapwood depth significantly impacted on the accuracy of thermal dissipation

  11. Accounting for sap flow from different parts of the root system improves the prediction of xylem ABA concentration in plants grown with heterogeneous soil moisture.

    Science.gov (United States)

    Dodd, Ian C; Egea, Gregorio; Davies, William J

    2008-01-01

    When soil moisture is heterogeneous, sap flow from, and ABA status of, different parts of the root system impact on leaf xylem ABA concentration ([X-ABA]leaf). The robustness of a model for predicting [X-ABA]leaf was assessed. 'Two root-one shoot' grafted sunflower (Helianthus annuus L.) plants received either deficit irrigation (DI, each root system received the same irrigation volumes) or partial rootzone drying (PRD, only one root system was watered and the other dried the soil). Irrespective of whether relative sap flow was assessed using sap flow sensors in vivo or by pressurization of de-topped roots, each root system contributed similarly to total sap flow during DI, while sap flow from roots in drying soil declined linearly with soil water potential (Psisoil) during PRD. Although Psisoil of the irrigated pot determined the threshold Psisoil at which sap flow from roots in drying soil decreased, the slope of this decrease was independent of the wet pot Psisoil. Irrespective of whether sap was collected from the wet or dry root system of PRD plants, or a DI plant, root xylem ABA concentration increased as Psisoil declined. The model, which weighted ABA contributions of each root system according to the sap flow from each, almost perfectly explained [X-ABA] immediately above the graft union. That the model overestimated measured [X-ABA]leaf may result from changes in [X-ABA] along the transport pathway or an artefact of collecting xylem sap from detached leaves. The implications of declining sap flow through partially dry roots during PRD for the control of stomatal behaviour and irrigation scheduling are discussed.

  12. On the estimate of the transpiration in Mediterranean heterogeneous ecosystems with the coupled use of eddy covariance and sap flow techniques.

    Science.gov (United States)

    Corona, Roberto; Curreli, Matteo; Montaldo, Nicola; Oren, Ram

    2013-04-01

    content reflectometers and gravimetric method, and periodically leaf area index (LAI) PFTs are estimated. From 2012 sap flow sensors based on the thermal Dissipation Method are installed on numerous trees around the tower. Preliminary results show first the need of careful use sap flow sensors outputs which are affected by errors in the estimates of their main parameters, mainly allometric relationships between, for instance, sapwood area, diameter, canopy cover area, which affect the upscale of the local tree measurements to the site plot larger scale. Finally we demonstrate that the sap flow sensors are essential for the estimate of ET in such dry conditions, typical of Mediterranean ecosystems.

  13. Evapotranspiration partitioning and variation of sap flow in female and male parents of maize for hybrid seed production in arid region

    Science.gov (United States)

    Understanding the variation of sap flow in female and male parents of maize for hybrid seed production and evapotranspiration (ET) partitioning is useful in accurately determining water use of the female and male parents and improving irrigation management of maize for hybrid seed production. Sap fl...

  14. A comparison of daily water use estimates derived from constant-heat sap-flow probe values and gravimetric measurements in pot-grown saplings.

    Science.gov (United States)

    K.A. McCulloh; K. Winter; F.C. Meinzer; M. Garcia; J. Aranda; Lachenbruch B.

    2007-01-01

    The use of Granier-style heat dissipation sensors to measure sap flow is common in plant physiology, ecology, and hydrology. There has been concern that any change to the original Granier design invalidates the empirical relationship between sap flux density and the temperature difference between the probes. We compared daily water use estimates from gravimetric...

  15. [Effects of tree diameter at breast height and soil moisture on transpiration of Schima superba based on sap flow pattern and normalization].

    Science.gov (United States)

    Mei, Ting-ting; Zhao, Ping; Wang, Quan; Cai, Xi-an; Yu, Meng-hao; Zhu, Li-wei; Zou, Lü-liu; Zeng, Xiao-ping

    2010-10-01

    The eigenvalues of continuous sap flow pattern, i. e. , skewness and kurtosis, were used to investigate the water usage of Schima superba with different diameter at breast height (DBH), and the method of normalization was firstly applied to eliminate the effects of strong affecting factor (photosynthetic active radiation, PAR) to explore the possible relationship between weak affecting factor (soil moisture) and sap flow. Generally, the trees with larger DBH had smaller skewness of sap flux density and later-appeared but larger peak values, suggesting that much more water was transpired, and the larger trees showed smaller skewness and later-appeared larger peak values in wet season than in dry season, suggesting that more water was transpired in wet season. On the other hand, smaller trees had lesser differences in the skewness between dry and wet seasons, suggesting that there was no significant difference in the transpiration between the two seasons. The relationship between individual tree's transpiration and soil moisture was significant and positive after the two parameters being normalized with PAR peak values. When the soil moisture content was higher, the transpiration of the trees with larger DBH was steadily increasing with soil moisture, while that of the trees with moderate or smaller DBH had opposite trend, presumably due to their transpiration and water absorption were approached to the limit.

  16. SAP R/3账号权限管理方法及应用浅谈%SAP R/3 Account Authority Management Method and Application Overview

    Institute of Scientific and Technical Information of China (English)

    韩翔

    2013-01-01

    Introduction SAP R/3 system account authority control concept, implementation method: including ABAP program check authority object, account authority configuration. Involving combine role, single role, authority object profile, account pa-rameter,correlation between them. And a reasonable way to give account authority.%  介绍SAP R/3系统的账号权限控制概念,实现方法:包括ABAP程序检核“权限对象”,账号权限配置。涉及复合角色,单角色,权限对象,参数文件,账号参数之间的关系,以及合理赋予账号权限的方法。

  17. A comparison of daily water use estimates derived from constant-heat sap-flow probe values and gravimetric measurements in pot-grown saplings.

    Science.gov (United States)

    McCulloh, Katherine A; Winter, Klaus; Meinzer, Frederick C; Garcia, Milton; Aranda, Jorge; Lachenbruch, Barbara

    2007-09-01

    Use of Granier-style heat dissipation sensors to measure sap flow is common in plant physiology, ecology and hydrology. There has been concern that any change to the original Granier design invalidates the empirical relationship between sap flux density and the temperature difference between the probes. Here, we compared daily water use estimates from gravimetric measurements with values from variable length heat dissipation sensors, which are a relatively new design. Values recorded during a one-week period were compared for three large pot-grown saplings of each of the tropical trees Pseudobombax septenatum (Jacq.) Dugand and Calophyllum longifolium Willd. For five of the six individuals, P values from paired t-tests comparing the two methods ranged from 0.12 to 0.43 and differences in estimates of total daily water use over the week of the experiment averaged gravimetric measurements. This discrepancy could have been associated with naturally occurring gradients in temperature that reduced the difference in temperature between the probes, which would have caused the sensor method to underestimate water use. Our results indicate that substitution of variable length heat dissipation probes for probes of the original Granier design did not invalidate the empirical relationship determined by Granier between sap flux density and the temperature difference between probes.

  18. Chronological Sequence of Leaf Phenology, Xylem and Phloem Formation and Sap Flow of Quercus pubescens from Abandoned Karst Grasslands.

    Science.gov (United States)

    Lavrič, Martina; Eler, Klemen; Ferlan, Mitja; Vodnik, Dominik; Gričar, Jožica

    2017-01-01

    Intra-annual variations in leaf development, radial growth, including the phloem part, and sap flow have rarely been studied in deciduous trees from drought-prone environments. In order to understand better the chronological order and temporal course of these processes, we monitored leaf phenology, xylem and phloem formation and sap flow in Quercus pubescens from abandoned karst grasslands in Slovenia during the growing season of 2014. We found that the initial earlywood vessel formation started before bud opening at the beginning of April. Buds started to open in the second half of April and full leaf unfolding occurred by the end of May. LAI values increased correspondingly with leaf development. About 28% of xylem and 22% of phloem annual increment were formed by the time of bud break. Initial earlywood vessels were fully lignified and ready for water transport, indicating that they are essential to provide hydraulic conductivity for axial water flow during leaf development. Sap flow became active and increasing contemporarily with leaf development and LAI values. Similar early spring patterns of xylem sap flow and LAI denoted that water transport in oaks broadly followed canopy leaf area development. In the initial 3 weeks of radial growth, phloem growth preceded that of xylem, indicating its priority over xylem at the beginning of the growing season. This may be related to the fact that after bud break, the developing foliage is a very large sink for carbohydrates but, at the same time, represents a small transpirational area. Whether the interdependence of the chronological sequence of the studied processes is fixed in Q. pubescens needs to be confirmed with more data and several years of analyses, although the 'correct sequence' of processes is essential for synchronized plant performance and response to environmental stress.

  19. Chronological Sequence of Leaf Phenology, Xylem and Phloem Formation and Sap Flow of Quercus pubescens from Abandoned Karst Grasslands

    Science.gov (United States)

    Lavrič, Martina; Eler, Klemen; Ferlan, Mitja; Vodnik, Dominik; Gričar, Jožica

    2017-01-01

    Intra-annual variations in leaf development, radial growth, including the phloem part, and sap flow have rarely been studied in deciduous trees from drought-prone environments. In order to understand better the chronological order and temporal course of these processes, we monitored leaf phenology, xylem and phloem formation and sap flow in Quercus pubescens from abandoned karst grasslands in Slovenia during the growing season of 2014. We found that the initial earlywood vessel formation started before bud opening at the beginning of April. Buds started to open in the second half of April and full leaf unfolding occurred by the end of May. LAI values increased correspondingly with leaf development. About 28% of xylem and 22% of phloem annual increment were formed by the time of bud break. Initial earlywood vessels were fully lignified and ready for water transport, indicating that they are essential to provide hydraulic conductivity for axial water flow during leaf development. Sap flow became active and increasing contemporarily with leaf development and LAI values. Similar early spring patterns of xylem sap flow and LAI denoted that water transport in oaks broadly followed canopy leaf area development. In the initial 3 weeks of radial growth, phloem growth preceded that of xylem, indicating its priority over xylem at the beginning of the growing season. This may be related to the fact that after bud break, the developing foliage is a very large sink for carbohydrates but, at the same time, represents a small transpirational area. Whether the interdependence of the chronological sequence of the studied processes is fixed in Q. pubescens needs to be confirmed with more data and several years of analyses, although the ‘correct sequence’ of processes is essential for synchronized plant performance and response to environmental stress. PMID:28321232

  20. Effect of Nitrogen on Water Content, Sap Flow, and Tolerance of Rice Plants to Brown Planthopper, Nilaparvata lugens

    Institute of Scientific and Technical Information of China (English)

    LU Zhong-xian; S. VILLAREAL; YU Xiao-ping; K. L. HEONG; HU Cui

    2004-01-01

    Water content (WC) and sap flow from leaf sheath of rice plants with varying nitrogen levels at different growth stages,and fluctuations in relative water content (RWC) of rice plants being damaged by brown planthopper (BPH), Nilaparvata lugens were determined in the laboratory, and the tolerance of rice plants to BPH at different nitrogen regimes was evaluated in the greenhouse at International Rice Research Institute (IRRI), the Philippines. The results indicated that both WC and RWC were increased significantly, as the amount of sap flow from rice plants was reduced statistically, with the increase of nitrogen content in rice plants. RWC in rice plants applied with high nitrogen fertilizer decreased drastically by the injury of BPH nymphs, while the reduced survival duration of rice plants with the increase of nitrogen content was recorded. These may be considered to be one of the important factors in increasing the susceptibility to BPH damage on rice plants applied with nitrogen fertilizer.

  1. Effect of Nitrogen on Water Content, Sap Flow, and Tolerance of Rice Plants to Brown Planthopper, Nilaparvata lugens

    Institute of Scientific and Technical Information of China (English)

    LuZhong-xian; S.VILLAREAL; YuXiao-ping; K.L.HEONG; HuCui

    2004-01-01

    Water content (WC) and sap flow from leaf sheath of rice plants with varying nitrogen levels at different growth stages and fluctuations in relative water content (RWC) of rice plants being damaged by brown planthopper (BPH), Nilaparvata lugens were determincd in the laboratory, and the tolerance of rice plants to BPH at different nitrogen regimes was evaluated in the greenhouse at International Rice Research institute (1RRI), the Philippines. The results indicated that both WC and RWC were increased significantly, as the amount of sap flow from rice plants was reduced statistically, with the in crease of nitrogen content inrice plants. RWC in rice plants applied with high nitrogen fertilizer decreased drastically by the injury, of BPH nymphs, while the reduced survival duration of rice plants with the increase of nitrogen content was recorded. These may be considered to be one of the important factors in increasing the susceptibility' to BPH damage on rice plants applied with nitrogen fertilizer

  2. Environmental regulation of xylem sap flow and total conductance of Larix gmelinii trees in eastern Siberia.

    Science.gov (United States)

    Arneth, A.; Kelliher, F. M.; Bauer, G.; Hollinger, D. Y.; Byers, J. N.; Hunt, J. E.; McSeveny, T. M.; Ziegler, W.; Vygodskaya, N. N.; Milukova, I.; Sogachov, A.; Varlagin, A.; Schulze, E.-D.

    1996-01-01

    Xylem sap flow and environmental variables were measured on seven consecutive midsummer days in a 130-year-old Larix gmelinii (Rupr.) Rupr. forest located 160 km south of Yakutsk in eastern Siberia, Russia (61 degrees N, 128 degrees E, 300 m asl). The site received 20 mm of rainfall during the 4 days before measurements, and soil samples indicated that the trees were well watered. The tree canopy was sparse with a one-sided leaf area index of 1.5 and a tree density of 1760 ha(-1). On a clear day when air temperature ranged from 9 to 29 degrees C, and maximum air saturation deficit was 3.4 kPa, daily xylem sap flux (F) among 13 trees varied by an order of magnitude from 7 l day(-1) for subcanopy trees (representing 55% of trees in the forest) to 67 l day(-1) for emergent trees (representing 18% of trees in the forest). However, when based on xylem sap flux density (F'), calculated by dividing F by projected tree crown area (a surrogate for the occupied ground area), there was only a fourfold range in variability among the 13 trees, from 1.0 to 4.4 mm day(-1). The calculation of F' also eliminated systematic and large differences in F among emergent, canopy and subcanopy trees. Stand-level F', estimated by combining half-hourly linear relationships between F and stem cross-sectional area with tree size distribution data, ranged between 1.8 +/- 0.4 (standard deviation) and 2.3 +/- 0.6 mm day(-1). These stand-level F' values are about 0.6-0.7 mm day(-1) (30%) larger than daily tree canopy transpiration rates calculated from forest energy balance and understory evaporation measurements. Maximum total tree conductance for water vapor transfer (G(tmax), including canopy and aerodynamic conductances), calculated from the ratio of F' and the above-canopy air saturation deficit (D) for the eight trees with continuous data sets, was 9.9 +/- 2.8 mm s(-1). This is equivalent to a leaf-scale maximum stomatal conductance (g(smax)) of 6.1 mm s(-1), when expressed on a one

  3. Habitat moisture is an important driver of patterns of sap flow and water balance in tropical montane cloud forest epiphytes.

    Science.gov (United States)

    Darby, Alexander; Draguljić, Danel; Glunk, Andrew; Gotsch, Sybil G

    2016-10-01

    Microclimate in the tropical montane cloud forest (TMCF) is variable on both spatial and temporal scales and can lead to large fluctuations in both leaf-level transpiration and whole plant water use. While variation in transpiration has been found in TMCFs, the influence of different microclimatic drivers on plant water relations in this ecosystem has been relatively understudied. Within the TMCF, epiphytes may be particularly affected by natural variation in microclimate due to their partial or complete disassociation from soil resources. In this study, we examined the effects of seasonal microclimate on whole plant water balance in epiphytes in both an observational and a manipulative experiment. We also evaluated the effects of different microclimatic drivers using three hierarchical linear (mixed) models. On average, 31 % of total positive sap flow was recovered via foliar water uptake (FWU) over the course of the study. We found that precipitation was the greatest driver of foliar water uptake and nighttime sap flow in our study species and that both VPD and precipitation were important drivers to daytime sap flow. We also found that despite adaptations to withstand seasonal drought, an extended dry period caused severe desiccation in most plants despite a large reduction in leaf-level and whole plant transpiration. Our results indicate that the epiphytes studied rely on FWU to maintain positive water balance in the dry season and that increases in dry periods in the TMCF may be detrimental to these common members of the epiphyte community.

  4. Extensive investigation of the sap flow of maize plants in an oasis farmland in the middle reach of the Heihe River, Northwest China.

    Science.gov (United States)

    Zhao, Liwen; He, Zhibin; Zhao, Wenzhi; Yang, Qiyue

    2016-09-01

    A better understanding of the sap flow characteristics of maize plants is critical for improving irrigation water-use efficiency, especially for regions facing water resource shortages. In this study, sap flow rates, related soil-physics and plant-growth parameters, and meteorological factors, were simultaneously monitored in a maize field in two consecutive years, 2011 and 2012, and the sap flow rates of the maize plants were extensively analyzed based on the monitored data. Seasonal and daily variational characteristics were identified at different growth stages and under different weather conditions, respectively. The analyses on the relationships between sap flow rate and reference evapotranspiration (ET0), as well as several plant-growth parameters, indicate that the irrigation schedule can exert an influence on sap flow, and can consequently affect crop yield. The ranking of the main meteorological factors affecting the sap flow rate was: net radiation > air temperature > vapor pressure deficit > wind speed. For a quick estimation of sap flow rates, an empirical formula based on the two top influencing factors was put forward and verified to be reliable. The sap flow rate appeared to show little response to irrigation when the water content was relatively high, implying that some of the irrigation in recent years may have been wasted. These results may help to reveal the bio-physical processes of maize plants related to plant transpiration, which could be beneficial for establishing an efficient irrigation management system in this region and also for providing a reference for other maize-planting regions.

  5. Evaluation of sap flow and trunk diameter sensors for irrigation scheduling in early maturing peach trees.

    Science.gov (United States)

    Conejero, W; Alarcón, J J; García-Orellana, Y; Nicolás, E; Torrecillas, A

    2007-12-01

    Five-year-old early maturing peach trees (Prunus persica (L.) Batsch cv. Flordastar grafted on GF-677 peach rootstock) were subjected to three irrigation treatments from March 18 to November 10, 2006. Control plants (T0 treatment) which received irrigation in excess of their crop water requirements (1089.7 mm) were compared with plants watered according to sap flow (SF; T1 treatment) or maximum daily trunk shrinkage (MDS; T2 treatment) measurements, so as to maintain SF and MDS signal intensities (control SF/SF in T1 and MDS in T2/control MDS, respectively) close to unity. When SF or MDS signal intensity on at least two of three consecutive days was at or below unity, irrigation was reduced by 10%. When the MDS signal intensity on at least two of three consecutive days exceeded unity, irrigation was increased by 10%. During the experiment, estimated crop evapotranspiration was 704.9 mm, and the cumulative amounts of applied water in the T1 and T2 treatments were 463.2 and 654.5 mm, respectively. The MDS-signal-intensity-driven irrigation schedule was more suitable than the SF-signal-intensity-driven irrigation schedule because it was more sensitive and reliable in detecting changes in plant water status, preventing the development of detectable plant water stress. Moreover, it had no effect on fruit size. We conclude that peach tree irrigation scheduling can be based on MDS measurements alone. Changes in the irrigation protocol assayed were proposed to reduce MDS signal intensity deviations above unity, for example, by increasing the irrigation scheduling frequency or the amount of water applied, or both. Irrigation schedules based on maintaining MDS signal intensities close to unity could be applied when local crop factor values are unavailable.

  6. A New Approach to Sap Flow Measurement Using 3D Printed Gauges and Open-source Electronics

    Science.gov (United States)

    Ham, J. M.; Miner, G. L.; Kluitenberg, G. J.

    2015-12-01

    A new type of sap flow gauge was developed to measure transpiration from herbaceous plants using a modified heat pulse technique. Gauges were fabricated using 3D-printing technology and low-cost electronics to keep the materials cost under $20 (U.S.) per sensor. Each gauge consisted of small-diameter needle probes fastened to a 3D-printed frame. One needle contained a resistance heater to provide a 6 to 8 second heat pulse while the other probes measured the resultant temperature increase at two distances from the heat source. The data acquisition system for the gauges was built from a low-cost Arduino microcontroller. The system read the gauges every 10 minutes and stored the results on a SD card. Different numerical techniques were evaluated for estimating sap velocity from the heat pulse data - including analytical solutions and parameter estimation approaches . Prototype gauges were tested in the greenhouse on containerized corn and sunflower. Sap velocities measured by the gauges were compared to independent gravimetric measurements of whole plant transpiration. Results showed the system could measure daily transpiration to within 3% of the gravimetric measurements. Excellent agreement was observed when two gauges were attached the same stem. Accuracy was not affected by rapidly changing transpiration rates observed under partly cloudy conditions. The gauge-based estimates of stem thermal properties suggested the system may also detect the onset of water stress. A field study showed the gauges could run for 1 to 2 weeks on a small battery pack. Sap flow measurements on multiple corn stems were scaled up by population to estimate field-scale transpiration. During full canopy cover, excellent agreement was observed between the scaled-up sap flow measurements and reference crop evapotranspiration calculated from weather data. Data also showed promise as a way to estimate real-time canopy resistance required for model verification and development. Given the low

  7. Approximate Entropy as a measure of complexity in sap flow temporal dynamics of two tropical tree species under water deficit

    Directory of Open Access Journals (Sweden)

    Gustavo M. Souza

    2004-09-01

    Full Text Available Approximate Entropy (ApEn, a model-independent statistics to quantify serial irregularities, was used to evaluate changes in sap flow temporal dynamics of two tropical species of trees subjected to water deficit. Water deficit induced a decrease in sap flow of G. ulmifolia, whereas C. legalis held stable their sap flow levels. Slight increases in time series complexity were observed in both species under drought condition. This study showed that ApEn could be used as a helpful tool to assess slight changes in temporal dynamics of physiological data, and to uncover some patterns of plant physiological responses to environmental stimuli.Entropia Aproximada (ApEn, um modelo estatístico independente para quantificar irregularidade em séries temporais, foi utilizada para avaliar alterações na dinâmica temporal do fluxo de seiva em duas espécies arbóreas tropicais submetidas à deficiência hídrica. A deficiência hídrica induziu uma grande redução no fluxo de seiva em G. ulmifolia, enquanto que na espécie C. legalis manteve-se estável. A complexidade das séries temporais foi levemente aumentada sob deficiência hídrica. O estudo mostrou que ApEn pode ser usada como um método para detectar pequenas alterações na dinâmica temporal de dados fisiológicos, e revelar alguns padrões de respostas fisiológicas a estímulos ambientais.

  8. Variable coupling between sap-flow and transpiration in pine trees under drought conditions

    Science.gov (United States)

    Preisler, Yakir; Tatarinov, Fyodor; Rohatyn, Shani; Rotenberg, Eyal; Grunzweig, Jose M.; Yakir, Dan

    2016-04-01

    Changes in diurnal patterns in water transport and physiological activities in response to changes in environmental conditions are important adjustments of trees to drought. The rate of sap flow (SF) in trees is expected to be in agreement with the rate of tree-scale transpiration (T) and provides a powerful measure of water transport in the soil-plant-atmosphere system. The aim of this five-years study was to investigate the temporal links between SF and T in Pinus halepensis exposed to extreme seasonal drought in the Yatir forest in Israel. We continuously measured SF (20 trees), the daily variations in stem diameter (ΔDBH, determined with high precision dendrometers; 8 trees), and ecosystem evapotranspiration (ET; eddy covariance), which were complemented with short-term campaigns of leaf-scale measurements of H2O and CO2 gas exchange, water potentials, and hydraulic conductivity. During the rainy season, tree SF was well synchronized with ecosystem ET, reaching maximum rates during midday in all trees. However, during the dry season, the daily SF trends greatly varied among trees, allowing a classification of trees into three classes: 1) Trees that remain with SF maximum at midday, 2) trees that advanced their SF peak to early morning, and 3) trees that delayed their SF peak to late afternoon hours. This classification remained valid for the entire study period (2010-2015), and strongly correlated with tree height and DBH, and to a lower degree with crown size and competition index. In the dry season, class 3 trees (large) tended to delay the timing of SF maximum to the afternoon, and to advance their maximum diurnal DBH to early morning, while class 2 trees (smaller) advanced their SF maximum to early morning and had maximum daily DBH during midday and afternoon. Leaf-scale transpiration (T), measurements showed a typical morning peak in all trees, irrespective of classification, and a secondary peak in the afternoon in large trees only. Water potential and

  9. Preservative treatment of Eucalyptus camaldulensis Dehnh. juvenile wood by sap displacement method

    Directory of Open Access Journals (Sweden)

    Pablo Marcel de Arruda Torres

    2011-06-01

    Full Text Available The research analyzed the quality of the preservative treatment of Eucalyptus camaldulensis Dehnh juvenile wood and verified the influence of the inversion of the pieces, in preservative solution, in the distribution, penetration and retention of CCB in treated pieces. Trees of Eucalyptus camaldulensis were collected in the rural area of the municipality of Rio Tinto, Paraíba, Brazil, in a stand aged four years. In the stand were randomly chosen five trees, being three of them with the larger diameter. For the wood treatment it was used the sap displacement method by radial transpiration using a 2% solution of ingredients copper chrome borate (CCB and compared the effect of the inversion of pieces on the preservative solution. The distribution, penetration and retention were better in reversed pieces when compared with the ones non-reversed in the preservative solution.

  10. Método de dissipação térmica para determinação do fluxo de seiva em coqueiro anão-verde The heat dissipation method for sap flow determination in green-dwarf coconut plants

    Directory of Open Access Journals (Sweden)

    Marilaine Campanati Araújo

    2012-01-01

    Full Text Available O conhecimento da demanda hídrica das culturas é uma informação básica para o manejo de irrigação. O método de dissipação térmica (MDT vem recebendo atenção nos últimos tempos para esta finalidade, em virtude de utilizar princípios físicos relativamente simples e poder ser aplicado diretamente no campo. Este trabalho objetivou realizar a calibração do método de sonda de dissipação térmica na determinação do fluxo de seiva em coqueiro anão-verde. Para a calibração, a sonda foi inserida em um segmento de pecíolo da folha do coqueiro-anão verde. Um fluxo estável de água foi estabelecido no segmento do pecíolo. Foram feitas medidas de vazão, volume por unidade de tempo, e temperatura, dada pela sonda. Após a calibração em laboratório foram realizados experimentos de campo na Região Norte Fluminense, Brasil, nos quais o modelo calibrado foi capaz de acompanhar a demanda atmosférica. Conclui-se que modelo matemático obtido da calibração do MDT é satisfatório para a obtenção da transpiração no coqueiro anão-verde.The knowledge of crop water demand is basic for irrigation management. In recent years, the Heat Dissipation Method (HDM has received attention for this purpose because its relatively simple physical principles and applicability in field conditions. This study aimed to perform calibration of the HDM for sap flow determination in green-dwarf coconut plants. For calibration, the probe was inserted in a segment of the leaf petiole of a dwarf coconut tree. A steady stream of water was established in the segment of petiole. Measurements of flow rate, volume per unit time and temperature, were taken with the probe. After calibrating HDM in laboratory, field experiments were carried out in the Norte Fluminense, Brazil, where the calibrated model were well coupled to the atmospheric demand. It is concluded that the mathematical model obtained in the HDM calibration is suitable for obtaining the

  11. Método de dissipação térmica para determinação do fluxo de seiva em coqueiro anão-verde The heat dissipation method for sap flow determination in green-dwarf coconut plants

    Directory of Open Access Journals (Sweden)

    Marilaine Campanati Araújo

    2013-01-01

    Full Text Available O conhecimento da demanda hídrica das culturas é uma informação básica para o manejo de irrigação. O método de dissipação térmica (MDT vem recebendo atenção nos últimos tempos para esta finalidade, em virtude de utilizar princípios físicos relativamente simples e poder ser aplicado diretamente no campo. Este trabalho objetivou realizar a calibração do método de sonda de dissipação térmica na determinação do fluxo de seiva em coqueiro anão-verde. Para a calibração, a sonda foi inserida em um segmento de pecíolo da folha do coqueiro-anão verde. Um fluxo estável de água foi estabelecido no segmento do pecíolo. Foram feitas medidas de vazão, volume por unidade de tempo, e temperatura, dada pela sonda. Após a calibração em laboratório foram realizados experimentos de campo na Região Norte Fluminense, Brasil, nos quais o modelo calibrado foi capaz de acompanhar a demanda atmosférica. Conclui-se que modelo matemático obtido da calibração do MDT é satisfatório para a obtenção da transpiração no coqueiro anão-verde.The knowledge of crop water demand is basic for irrigation management. In recent years, the Heat Dissipation Method (HDM has received attention for this purpose because its relatively simple physical principles and applicability in field conditions. This study aimed to perform calibration of the HDM for sap flow determination in green-dwarf coconut plants. For calibration, the probe was inserted in a segment of the leaf petiole of a dwarf coconut tree. A steady stream of water was established in the segment of petiole. Measurements of flow rate, volume per unit time and temperature, were taken with the probe. After calibrating HDM in laboratory, field experiments were carried out in the Norte Fluminense, Brazil, where the calibrated model were well coupled to the atmospheric demand. It is concluded that the mathematical model obtained in the HDM calibration is suitable for obtaining the

  12. Seasonal shift in climatic limiting factors on tree transpiration: evidence from sap flow observations at alpine treelines in southeast Tibet

    Directory of Open Access Journals (Sweden)

    Liu Xinsheng

    2016-07-01

    Full Text Available Alpine and northern treelines are primarily controlled by low temperatures. However, little is known about the impact of low soil temperature on tree transpiration at treelines. We aim to test the hypothesis that in cold-limited forests, the main limiting factors for tree transpiration switch from low soil temperature before summer solstice to atmospheric evaporative demand after summer solstice, which generally results in low transpiration in the early growing season. Sap flow, meteorological factors and predawn needle water potential were continuously monitored throughout one growing season across Smith fir (Abies georgei var. smithii and juniper (Juniperus saltuaria treelines in southeast Tibet. Sap flow started in early May and corresponded to a threshold mean air-temperature of 0 oC. Across tree species, transpiration was mainly limited by low soil temperature prior to the summer solstice but by vapor pressure deficit and solar radiation post-summer solstice, which was further confirmed on a daily scale. As a result, tree transpiration for both tree species was significantly reduced in the pre-summer solstice period as compared to post-summer solstice, resulting in a lower predawn needle water potential for Smith fir trees in the early growing season. Our data supported the hypothesis, suggesting that tree transpiration mainly responds to soil temperature variations in the early growing season. The results are important for understanding the hydrological response of cold-limited forest ecosystems to climate change.

  13. Seasonal Shift in Climatic Limiting Factors on Tree Transpiration: Evidence from Sap Flow Observations at Alpine Treelines in Southeast Tibet.

    Science.gov (United States)

    Liu, Xinsheng; Nie, Yuqin; Luo, Tianxiang; Yu, Jiehui; Shen, Wei; Zhang, Lin

    2016-01-01

    Alpine and northern treelines are primarily controlled by low temperatures. However, little is known about the impact of low soil temperature on tree transpiration at treelines. We aim to test the hypothesis that in cold-limited forests, the main limiting factors for tree transpiration switch from low soil temperature before summer solstice to atmospheric evaporative demand after summer solstice, which generally results in low transpiration in the early growing season. Sap flow, meteorological factors and predawn needle water potential were continuously monitored throughout one growing season across Smith fir (Abies georgei var. smithii) and juniper (Juniperus saltuaria) treelines in southeast Tibet. Sap flow started in early May and corresponded to a threshold mean air-temperature of 0°C. Across tree species, transpiration was mainly limited by low soil temperature prior to the summer solstice but by vapor pressure deficit and solar radiation post-summer solstice, which was further confirmed on a daily scale. As a result, tree transpiration for both tree species was significantly reduced in the pre-summer solstice period as compared to post-summer solstice, resulting in a lower predawn needle water potential for Smith fir trees in the early growing season. Our data supported the hypothesis, suggesting that tree transpiration mainly responds to soil temperature variations in the early growing season. The results are important for understanding the hydrological response of cold-limited forest ecosystems to climate change.

  14. Biodiversity Monitoring at the Tonle Sap Lake of Cambodia: A Comparative Assessment of Local Methods

    Science.gov (United States)

    Seak, Sophat; Schmidt-Vogt, Dietrich; Thapa, Gopal B.

    2012-10-01

    This paper assesses local biodiversity monitoring methods practiced in the Tonle Sap Lake of Cambodia. For the assessment we used the following criteria: methodological rigor, perceived cost, ease of use (user friendliness), compatibility with existing activities, and effectiveness of intervention. Constraints and opportunities for execution of the methods were also considered. Information was collected by use of: (1) key informant interview, (2) focus group discussion, and (3) researcher's observation. The monitoring methods for fish, birds, reptiles, mammals and vegetation practiced in the research area have their unique characteristics of generating data on biodiversity and biological resources. Most of the methods, however, serve the purpose of monitoring biological resources rather than biodiversity. There is potential that the information gained through local monitoring methods can provide input for long-term management and strategic planning. In order to realize this potential, the local monitoring methods should be better integrated with each other, adjusted to existing norms and regulations, and institutionalized within community-based organization structures.

  15. Comparison of sap flux, moisture flux tower and MODIS enhanced vegetation index methods for estimating riparian evapotranspiration

    Science.gov (United States)

    Nagler, Pamela L.; Glenn, Edward P.; Morino, Kiyomi; Neale, Christopher M.U; Cosh, Michael H.

    2010-01-01

    Riparian evapotranspiration (ET) was measured on a salt cedar (Tamarix spp.) dominated river terrace on the Lower Colorado River from 2007 to 2009 using tissue-heat-balance sap flux sensors at six sites representing very dense, medium dense, and sparse stands of plants. Salt cedar ET varied markedly across sites, and sap flux sensors showed that plants were subject to various degrees of stress, detected as mid-day depression of transpiration and stomatal conductance. Sap flux results were scaled from the leaf level of measurement to the stand level by measuring plant-specific leaf area index and fractional ground cover at each site. Results were compared to Bowen ratio moisture tower data available for three of the sites. Sap flux sensors and flux tower results ranked the sites the same and had similar estimates of ET. A regression equation, relating measured ET of salt cedar and other riparian plants and crops on the Lower Colorado River to the Enhanced Vegetation Index from the MODIS sensor on the Terra satellite and reference crop ET measured at meteorological stations, was able to predict actual ET with an accuracy or uncertainty of about 20%, despite between-site differences for salt cedar. Peak summer salt cedar ET averaged about 6 mm d-1 across sites and methods of measurement.

  16. Assessing dam development, land use conversion, and climate change pressures on tributary river flows and water quality of the Mekong's Tonle Sap basin.

    Science.gov (United States)

    Cochrane, T. A.; Arias, M. E.; Oeurng, C.; Arnaiz, M.; Piman, T.

    2016-12-01

    The Tonle Sap Lake is Southeast Asia's most productive freshwater fishery, but the productivity of this valuable ecosystem is under threat from extensive development in the lower Mekong. With dams potentially blocking all major tributaries along the lower Mekong River, the role of local Tonle Sap basin tributaries for maintaining environmental flows, sediment loads, and fish recruitment is becoming increasingly critical. Development within the Tonle Sap basin, however, is not stagnant. Developers are proposing extensive dam development in key Tonle Sap tributaries (see Figure). Some dams will provide hydroelectricity and others will provide opportunities for large-scale irrigation resulting in agro-industrial expansion. There is thus an immediate need to assess the current situation and understand future effects of dam development and land use conversion under climate change on local riverine ecosystems. A combination of remote sensing, field visits, and hydro-meteorological data analyses enabled an assessment of water infrastructure and agricultural development in the basin. The application of SWAT for modelling flows and water quality combined with HEC-RESSIM for reservoir operations enabled for a holistic modelling approach. Initial results show that dams and land use change dominate flow and water quality responses, when compared to climate change. Large ongoing dam and irrigation development in the Pursat and Battambang subbasins will critically alter the natural river flows to the Tonle Sap Lake. Some of the observed dams did not have provisions for sediment flushing, clearing of flooded areas, fish passages, or other environmental protection measures. Poor planning and operation of this infrastructure could have dire consequences on the fragile riverine ecosystem of Tonle Sap tributaries, resulting in fish migration barriers, losses in aquatic habitats, and ecological degradation. The seemingly chaotic development in the Tonle Sap basin induces a great level

  17. Water-use efficiency within a selection of indigenous and exotic tree species in South Africa as determined using sap flow and biomass measurements

    CSIR Research Space (South Africa)

    Gush, Mark B

    2008-10-01

    Full Text Available of the water-use efficiency (WUE) of a selection of indigenous tree species yielding potentially useful wood. Hourly sap flow rates (water use) over a 12-month period were recorded in a selection of indigenous tree species. Stem and branch dimensions were...

  18. Studies on the interactions of SAP-1 (an N-terminal truncated form of cystatin S) with its binding partners by CD-spectroscopic and molecular docking methods.

    Science.gov (United States)

    Yadav, Vikash Kumar; Mandal, Rahul Shubhra; Puniya, Bhanwar Lal; Singh, Sarman; Yadav, Savita

    2015-01-01

    SAP-1 is a 113 amino acid long single-chain protein which belongs to the type 2 cystatin gene family. In our previous study, we have purified SAP-1 from human seminal plasma and observed its cross-class inhibitory property. At this time, we report the interaction of SAP-1 with diverse proteases and its binding partners by CD-spectroscopic and molecular docking methods. The circular dichroism (CD) spectroscopic studies demonstrate that the conformation of SAP-1 is changed after its complexation with proteases, and the alterations in protein secondary structure are quantitatively calculated with increase of α-helices and reduction of β-strand content. To get insight into the interactions between SAP-1 and proteases, we make an effort to model the three-dimensional structure of SAP-1 by molecular modeling and verify its stability and viability through molecular dynamics simulations and finally complexed with different proteases using ClusPro 2.0 Server. A high degree of shape complementarity is examined within the complexes, stabilized by a number of hydrogen bonds (HBs) and hydrophobic interactions. Using HB analyses in different protein complexes, we have identified a series of key residues that may be involved in the interactions between SAP-1 and proteases. These findings will assist to understand the mechanism of inhibition of SAP-1 for different proteases and provide intimation for further research.

  19. Canopy stomatal uptake of NOX, SO2 and O3 by mature urban plantations based on sap flow measurement

    Science.gov (United States)

    Hu, Yanting; Zhao, Ping; Niu, Junfeng; Sun, Zhenwei; Zhu, Liwei; Ni, Guangyan

    2016-01-01

    Canopy stomatal uptake of NOX (NO, NO2), SO2 and O3 by three mature urban plantations (of Schima superba, Eucalyptus citriodora and Acacia auriculaeformis) were studied using the sap flow-based approach under free atmospheric conditions. The annual mean concentration for NO, NO2, SO2 and O3 were 18.2, 58.1, 12.8 and 42.4 μg m-3, respectively. The atmospheric concentration exhibited a spring or winter maximum for NO, NO2 and SO2, whereas the concentration maximum for O3 occurred in the autumn. Despite the daytime mean canopy stomatal conductance (GC) being positively related with the photosynthetically active radiation (PAR) and negatively with the vapour pressure deficit (VPD), the maximal daytime mean GC did not appear when the PAR was at its highest level or the VPD was at its lowest level because a positive correlation was noted between the daytime mean PAR and VPD (P < 0.001) under field conditions. The GC value was regulated by the cooperation of the PAR and VPD. When analysing the respective effect of the PAR or VPD on GC separately, a positive logarithmical correlation was noted between the daytime mean GC and PAR as the following equation:Gc = a × lnPAR - b (P < 0.01), and the daytime mean GC was negatively logarithmically correlated with the VPD: Gc =Gsref - m × lnVPD (P < 0.001). The daytime mean GC declined with decreases in the soil water content (SWC) under similar meteorological condition. Differences in the seasonal pattern of the canopy stomatal conductance and atmospheric concentrations led to a differentiated peak flux. The flux for NO, NO2 and SO2 exhibited a spring maximum, whereas the flux maximum for O3 appeared in the autumn or summer. The annual cumulative stomatal flux for NO, NO2, O3 and SO2 was 100.19 ± 3.76, 510.68 ± 24.78, 748.59 ± 52.81 and 151.98 ± 9.33 mg m-2 a-1, respectively. When we focus on the foliar uptake of trace gases, the effect of these gases on the vegetation in turn should be considered, particularly for regions

  20. Measuring Complexity of SAP Systems

    Directory of Open Access Journals (Sweden)

    Ilja Holub

    2016-10-01

    Full Text Available The paper discusses the reasons of complexity rise in ERP system SAP R/3. It proposes a method for measuring complexity of SAP. Based on this method, the computer program in ABAP for measuring complexity of particular SAP implementation is proposed as a tool for keeping ERP complexity under control. The main principle of the measurement method is counting the number of items or relations in the system. The proposed computer program is based on counting of records in organization tables in SAP.

  1. From Sap to Syrup

    Science.gov (United States)

    Bjork, Janna

    2005-01-01

    Warm days, cold nights, melting snow-signs winter is waning and spring is nearing. Though winter may just be getting started in some areas, it's always fun to appreciate the good things about winter, including the special time at the end of winter in New England known as "sugaring time." The sap starts flowing in the sugar maples, and the process…

  2. From Sap to Syrup

    Science.gov (United States)

    Bjork, Janna

    2005-01-01

    Warm days, cold nights, melting snow-signs winter is waning and spring is nearing. Though winter may just be getting started in some areas, it's always fun to appreciate the good things about winter, including the special time at the end of winter in New England known as "sugaring time." The sap starts flowing in the sugar maples, and…

  3. Interactive ion-mediated sap flow regulation in olive and laurel stems: physicochemical characteristics of water transport via the pit structure.

    Directory of Open Access Journals (Sweden)

    Jeongeun Ryu

    Full Text Available Sap water is distributed and utilized through xylem conduits, which are vascular networks of inert pipes important for plant survival. Interestingly, plants can actively regulate water transport using ion-mediated responses and adapt to environmental changes. However, ionic effects on active water transport in vascular plants remain unclear. In this report, the interactive ionic effects on sap transport were systematically investigated for the first time by visualizing the uptake process of ionic solutions of different ion compositions (K+/Ca2+ using synchrotron X-ray and neutron imaging techniques. Ionic solutions with lower K+/Ca2+ ratios induced an increased sap flow rate in stems of Olea europaea L. and Laurus nobilis L. The different ascent rates of ionic solutions depending on K+/Ca2+ ratios at a fixed total concentration increases our understanding of ion-responsiveness in plants from a physicochemical standpoint. Based on these results, effective structural changes in the pit membrane were observed using varying ionic ratios of K+/Ca2+. The formation of electrostatically induced hydrodynamic layers and the ion-responsiveness of hydrogel structures based on Hofmeister series increase our understanding of the mechanism of ion-mediated sap flow control in plants.

  4. Oil palm water use: calibration of a sap flux method and a field measurement scheme.

    Science.gov (United States)

    Niu, Furong; Röll, Alexander; Hardanto, Afik; Meijide, Ana; Köhler, Michael; Hendrayanto; Hölscher, Dirk

    2015-05-01

    Oil palm (Elaeis guineensis Jacq.) water use was assessed by sap flux density measurements with the aim to establish the method and derive water-use characteristics. Thermal dissipation probes were inserted into leaf petioles of mature oil palms. In the laboratory, we tested our set-up against gravimetric measurements and derived new parameters for the original calibration equation that are specific to oil palm petioles. In the lowlands of Jambi, Indonesia, in a 12-year-old monoculture plantation, 56 leaves on 10 palms were equipped with one sensor per leaf. A 10-fold variation in individual leaf water use among leaves was observed, but we did not find significant correlations to the variables trunk height and diameter, leaf azimuthal orientation, leaf inclination or estimated horizontal leaf shading. We thus took an un-stratified approach to determine an appropriate sampling design to estimate stand transpiration (Es, mm day(-1)) rates of oil palm. We used the relative standard error of the mean (SEn, %) as a measure for the potential estimation error of Es associated with sample size. It was 14% for a sample size of 13 leaves to determine the average leaf water use and four palms to determine the average number of leaves per palm. Increasing these sample sizes only led to minor further decreases of the SEn of Es. The observed 90-day average of Es was 1.1 mm day(-1) (error margin ± 0.2 mm day(-1)), which seems relatively low, but does not contradict Penman-Monteith-derived estimates of evapotranspiration. Examining the environmental drivers of Es on an intra-daily scale indicates an early, pre-noon maximum of Es rates (11 am) due to a very sensitive reaction of Es to increasing vapor pressure deficit in the morning. This early peak is followed by a steady decline of Es rates for the rest of the day, despite further rising levels of vapor pressure deficit and radiation; this results in pronounced hysteresis, particularly between Es and vapor pressure deficit.

  5. Investigating differences in the root to shoot transfer and xylem sap solubility of organic compounds between zucchini, squash and soybean using a pressure chamber method.

    Science.gov (United States)

    Garvin, Naho; Doucette, William J; White, Jason C

    2015-07-01

    A pressure chamber method was used to examine differences in the root to shoot transfer and xylem sap solubility of caffeine (log Kow=-0.07), triclocarban (log Kow=3.5-4.2) and endosulfan (log Kow=3.8-4.8) for zucchini (cucurbita pepo ssp pepo), squash (cucurbita pepo ssp ovifera), and soybean (glycine max L.). Transpiration stream concentration factors (TSCF) for caffeine (TSCF=0.8) were statistically equivalent for all plant species. However, for the more hydrophobic endosulfan and triclocarban, the TSCF values for zucchini (TSCF=0.6 and 0.4, respectively) were 3 and 10 times greater than the soybean and squash (TSCF=0.2 and 0.05, respectively). The difference in TSCF values was examined by comparing the measured solubilities of caffeine, endosulfan and triclocarban in deionized water to those in soybean and zucchini xylem saps using a modified shake flask method. The measured solubility of organic contaminants in xylem sap has not previously been reported. Caffeine solubilities in the xylem saps of soybean and zucchini were statistically equal to deionized water (21500mgL(-1)) while endosulfan and triclocarban solubilities in the zucchini xylem sap were significantly greater (0.43 and 0.21mgL(-1), respectively) than that of the soybean xylem sap (0.31 and 0.11mgL(-1), respectively) and deionized water (0.34 and 0.11mgL(-1), respectively). This suggests that the enhanced root to shoot transfer of hydrophobic organics reported for zucchini is partly due to increased solubility in the xylem sap. Further xylem sap characterization is needed to determine the mechanism of solubility enhancement.

  6. 浑善达克沙地榆树干液流动态研究%Sap Flow Dynamics of Ulmus pumila var.sabulosa in Hunshandake Sandland

    Institute of Scientific and Technical Information of China (English)

    王晶苑; 蒋高明; 刘美珍

    2011-01-01

    Sap flux density of Ulmus pumila var. Sabulosa in typical elms sparse forest in Hunshandake Sandland of Inner Mongolia was studied by using Cranier technology. Nine dominant trees with different Diameters at Breast Height (DBH) which belong to three classes of DBH, that is, 15-25cm (small DBH), 25-35cm (medium DBH) and >35cm (large DBH), respectively in natural forest were selected and measured in terms of sap flux density. At the same time, various environmental factors including air temperature, relative humidity, photosynthetically active radiation, and wind speed were monitored in the whole growing season. The sap flow characteristics of forest stand are: sap flow density peak value of large DBH is larger than that of medium DBH tree and then small DBH tree. Sap flow density of large DBH trees change gently because age of stand. Average monthly sap flow density is less with the shift of growing season; the sap flow density enters into the state of weakly fluctuation in the end of growing season (October). The maximum value of average monthly sap flow density for varied tree species appears from June to August, the differences among dominant, medium and small trees are large. The main influence environmental factors are VPD, PAR, Ta. At different months, the dominant environmental factors have changed, but the two main factors are PAR and VPD.%应用Granier热扩散技术对内蒙古浑善达克沙地榆(Ulmus pumila var.sabulosa)疏林林分进行树干液流通量研究.选择该区占林分80%以上林木的3种胸径级(小径级,15-25cm;中等径级,25-35cm;大径级,>35cm)榆树,使用Granier探针进行每隔15min的树干液流测定,同步测定各林分环境因子.林分中不同胸径级榆树树干液流通量特征表现为:树干液流密度峰值大径级树>中等径级树>小径级树,且差异明显;大径级树由于林龄较大,液流密度曲线变化平缓,没有明显的峰值,呈弧形曲线;液流密度随季节推移在生

  7. Study on the sap flow of Atraphaxis bracteata growing in Mu us Sand%沙木蓼蒸腾耗水规律研究

    Institute of Scientific and Technical Information of China (English)

    樊文会; 丁国栋; 吴斌; 张宇清; 乌日娜

    2012-01-01

    To reveal the evapotransporation of Atraphaxis bracteata in Mu us Sandy land,Heat-balance Packaged Stem Sap Flow Measuring System and Automatic Weather Station System were used to simultaneously measure and monitor the sap flow velocity and related environmental factors.The results showed that:(1) Sap flow rate of Atraphaxis bracteata ascend and descend with the sunrise and sunset,it keep at peak for 8 hours in day.There is still sap flow in night for water storage in plants.(2) The process of sap flow rate is obviously affected by weather.In rainy days the flow drop to a rather low rate,but in night it rise greatly,the total flow is half of that on sunny days.There is a relatively small difference in flow rate of day and night in cloudy wheather,and the total flow reduces.In cloudy days,with the cloud moving,sap flow fluctuates,but total flow isn't affected so much.(3) Sap flow of A.bracteata in the growing season is related with the soil water and vegetation storage.From the vigorous vegetative growth in June and July to the reproductive stage in August,the soil water exhausts,generally the sap flow is gradually decrease.(4) Sap flow of A.bracteata with different sizes of stem and crown drift simultaneously and in proportion to stem diameter.From May to July,total sap flow of A.bracteata with the stem diameters of 9mm,16mm and 25mm,are 100.8kg,170.5kg,301.3kg,respectively,average as 11.5kg/mm/a.It can be used to calculate the total evaporation of a known forest of A.bracteata.%采用热平衡包裹式树干茎流测量系统(Stem Heat Balance,SHB)和自动气象站观测沙木蓼生长季茎干液流以及环境因子,以揭示毛乌素沙地沙木蓼(Atraphaxis bracteata A.Los)蒸腾耗水规律。结果表明:1)沙木蓼液流具有明显的昼夜节律,启动、停止与日出、日落同步,夜间仍保持一定液流,以补充植物体水分亏缺。2)沙木蓼液流规律受天气影响显著:降雨时白天的液流速率大幅下降,夜

  8. Transpiration of montane Pinus sylvestris L. and Quercus pubescens Willd. forest stands measured with sap flow sensors in NE Spain

    Directory of Open Access Journals (Sweden)

    R. Poyatos

    2005-01-01

    Full Text Available Stand transpiration was measured during the 2003 and 2004 growing seasons using heat dissipation sap flow sensors in a Scots pine (Pinus sylvestris L. and a pubescent oak (Quercus pubescens Willd. forests located in a montane area of the Eastern Pyrenees (NE Spain. The first aim of the study was to assess the differences in quantitative estimates of transpiration (Ec and the response to evaporative demand of the two stands. Over the studied period of 2003, characterised by a severe drought episode during the summer, the oak stand (Ec was only 110 mm compared to the 239 mm transpired by the Scots pine stand, although the ratio of transpiration to reference evapotranspiration (Ec/ET0 in the oak stand compares well with the expected values predicted for low leaf area index (LAI oak forests in southern Europe. Scots pine showed a strong reduction in (Ec/ET0 as the drought developed, whereas pubescent oak was less affected by soil moisture deficits in the upper soil. As a second objective, and given the contrasting meteorological conditions between 2003 and 2004 summer periods, the interannual variability of transpiration was studied in the Scots pine plot. Rainfall during the summer months (June-September in 2003 was almost 40% less than in the same interval in 2004. Accordingly, transpiration was also reduced about 25% in 2003. Finally, Scots pine data from 2003 and 2004 was used to calibrate a simple transpiration model using ET0 and soil moisture deficit (SMD as input variables, and implicitly including stomatal responses to high vapour pressure deficits (Dd and soil water status.

  9. Switching the light off: A break in photosynthesis and sap flow of forest trees under total solar eclipse

    Directory of Open Access Journals (Sweden)

    Karl-Heinz Häberle

    2001-05-01

    Full Text Available In mature trees of Picea abies, Fagus sylvatica and Quercus robur, photosynthesis and transpiration were assessed in response to the total solar eclipse that occurred in Central Europe during the late morning hours of August 11, 1999, a day with changing cloudiness. Measurements were conducted at three forest sites located in the totality zone and the 99% area of the eclipse within a radius of about 100 km around the city of Munich (southern Germany. The eclipse lasting 164 minutes lowered the photosynthetic photon flux density (PPFD to about 1 μmol m-2 s-1 during the 2-minute totality period, when the sky was clear. During totality, photosynthesis was reduced to an extent that allowed CO2 release to dominate the gas exchange of leaves. Effects on transpiration were less pronounced as the totality was apparently too short to induce distinct stomatal closure in response to low PPFD. Transpiration was strongly reduced, however, by increased air humidity and wet leaf surfaces during sporadic rain showers which preceded or succeeded the eclipse during the same day, whereas low PPFD through intermittent cloudiness during rain only moderately reduced photosynthesis. Although transpiration was lowered to a minor extent only by the eclipse, the latter affected the water transport through the whole tree, as reflected in a decline in the sap flow rate through the basal stem part with a time delay depending on the species. Nevertheless, trees responded in a synchronous way, regardless of the site, species or the percent degree of the eclipse.

  10. INTEGRATION OF THE SAP CONCEPT IN THE EMPLOYEE ASSESSMENT OF TRAVEL AGENCIES IN SUCEAVA COUNTY THROUGH MYSTERY SHOPPING TYPE METHODS

    Directory of Open Access Journals (Sweden)

    Cristian Valentin HAPENCIUC

    2014-07-01

    Full Text Available Being on a positive trend and addressing to a market that is less willing to compromise, the tourism industry develops a highly complex content, represented by various organizations and services, having as a main objective meeting the expectations of consumers of tourism services and reporting to the challenges of contemporary dynamics generated by the emergence of new information technologies. To respond effectively to these issues, tourism requires among other things a modern HR management. For travel agencies, human resources are the main asset of the company that serves to implement the entity's objectives. The most important qualities of the travel agent are polite attitude, promptness, sagacity and firmness. However, the ability to display with celerity their own capabilities - intellectual, psycho-motivational and persuasive - represents the quintessence of the travel agent profession. When we refer to these features, in the universal tourism language we talk about SAP concept: Speed, Accuracy, Politeness. Therefore, the major objective of this study aims to assess the employees of travel agencies from Suceava County in terms of SAP components using three different methods of qualitative research: Mystery Shopping, Mystery Calling and Mystery Emailing.

  11. Correlation of maple sap composition with bacterial and fungal communities determined by multiplex automated ribosomal intergenic spacer analysis (MARISA).

    Science.gov (United States)

    Filteau, Marie; Lagacé, Luc; LaPointe, Gisèle; Roy, Denis

    2011-08-01

    During collection, maple sap is contaminated by bacteria and fungi that subsequently colonize the tubing system. The bacterial microbiota has been more characterized than the fungal microbiota, but the impact of both components on maple sap quality remains unclear. This study focused on identifying bacterial and fungal members of maple sap and correlating microbiota composition with maple sap properties. A multiplex automated ribosomal intergenic spacer analysis (MARISA) method was developed to presumptively identify bacterial and fungal members of maple sap samples collected from 19 production sites during the tapping period. Results indicate that the fungal community of maple sap is mainly composed of yeast related to Mrakia sp., Mrakiella sp., Guehomyces pullulans, Cryptococcus victoriae and Williopsis saturnus. Mrakia, Mrakiella and Guehomyces peaks were identified in samples of all production sites and can be considered dominant and stable members of the fungal microbiota of maple sap. A multivariate analysis based on MARISA profiles and maple sap chemical composition data showed correlations between Candida sake, Janthinobacterium lividum, Williopsis sp., Leuconostoc mesenteroides, Mrakia sp., Rhodococcus sp., Pseudomonas tolaasii, G. pullulans and maple sap composition at different flow periods. This study provides new insights on the relationship between microbial community and maple sap quality.

  12. ECONOMICAL VIABILITY OF PRESERVATIVE TREATMENT OF Prosopis juliflora (SW D.C. WOOD SUBMITTED TO SAP DISPLACEMENT METHOD

    Directory of Open Access Journals (Sweden)

    Desmoulis Wanderley de Farias Sobrinho

    2008-06-01

    Full Text Available This work aimed to evaluate the economical viability of preservative treatment of Prosopis juliflora (Sw D.C. roundpieces treated with Osmose CCB commercial preservative applied by sap displacement method in rural property and to comparetheir costs with Mimosa caesalpiniifolia, Mimosa tenuiflora and Prosopis juliflora non-treated pieces costs. The treatment of Prosopisjuliflora wood demonstrated to be economically viable when compared to alternatives using the Equivalent Annual Costs (EACs, fordiscount rates of 12; 15; and 18% and expected useful life varying from 16 to 30 years, in these situations treated Prosopis juliflorawood presented smaller EAC than Mimosa caesalpiniifolia, Mimosa tenuiflora and Prosopis juliflora non-treated woods for theanalyzed situations, that justifies the employment of the Prosopis juliflora treated logs as fence posts and other similar uses.

  13. Diurnal and Seasonal Changes in Stem Radius Increment and Sap Flow Density Indicate Different Responses of Two Co-existing Oak Species to Drought Stress

    Directory of Open Access Journals (Sweden)

    MÉSZÁROS, Ilona

    2011-01-01

    Full Text Available Using continuous monitoring of stem radius combined with sap flow measurements weassessed the effects of environmental conditions on tree radial growth and water status of two coexistingoak species (Quercus petraea and Quercus cerris at high resolution time in growingseasons of 2008 and 2009. The forest (95–100 yr is situated in a xeric site in the transition zonebetween forested and forest-steppe regions in north-eastern Hungary, Bükk mountains (47o90’N,20o46’E, elevation 320–340 m a.s.l.. Weather conditions in the growing season of 2008 (totalrainfall 354 mm, mean daily temperature 17.0 oC was less extreme than in 2009 (total rainfall299 mm, temperature 17.9 oC. Rainfall strongly determined the course of radial growth incrementin trees. Radial growth of trees was limited in 2009 due to the drought in spring. The maximumradial increment of both species was achieved three weeks earlier (4th week of June than in 2008(4th week of July. We used dendrometer monitoring data for estimation of stem (tree waterdeficit (W by measuring water-related changes in stem radius (Zweifel et al. 2005. Themagnitude of tree water deficit variation (W was always smaller in Q. cerris than in Q. petraea.In contrast, Quercus cerris always exhibited larger daytime averages and maxima of sap flowdensity. In August of 2009 when drought became severe there were larger increases in tree waterdeficit (W (50–55 % in both species compared to July as it could be expected from the extentof decreases in sap flow density (24–28%. Our data suggested that due to the low SWC thetranspiration was supported mainly from the inner water storage of trees during prolonged droughtwhich resulted in high stem water deficit (W.

  14. The Relationship between Sap Flow Density and  Environmental Factors in the Yangtze River Delta  Region of China

    Directory of Open Access Journals (Sweden)

    Xin Liu

    2017-03-01

    Full Text Available Canopy transpiration is an important component of evapotranspiration, integrating physical and biological processes within the water and energy cycles of forests. Quercus acutissima and Cunninghamia lanceolata are two important, fast‐growing and commercial tree species that have been extensively used for vegetation restoration, water conservation and building artificial forests in the Yangtze River Delta region of China. The primary objective of this study was to characterize sap flow densities of the two species by comparing daytime and nocturnal sap flow patterns and their relationships with environmental factors. Sap flow densities (Sd were measured between September 2012 and August 2013 using the commercially‐available thermal dissipation probes. Hourly meteorological data were measured in an open field, located 200 m away from the study site, including photosynthetically‐active radiation (Par, air temperature (Ta, relative air humidity (Rh, vapor pressure deficit (Vpd and precipitation (P. Soil water content (Swc data were logged hourly in different layers at Q. acutissima and C. lanceolata forests. Results indicated that the mean Sd in summer was higher than that in spring and autumn. Both the Sd of Q. acutissima and C. lanceolata showed distinct diurnal patterns. Nocturnal sap flow densities (Sdn were noticeable, and both species followed similar declining patterns during our study period. The daytime sap flow density (Sdd was more sensitive to environmental factors than Sdn. Sap flow density was significant linearly correlated with Par, Vpd and Ta, and Par and Vpd explained the greatest amount of variation in daytime sap flow of Q. acutissima and C. lanceolata, respectively. Our study will enrich knowledge of plantation forest physical and biological processes and provide valuable information for plantation forest management in the Yangtze River Delta region of China.

  15. 尾巨桉液流特征分析%Analysis on sap flow characteristics of Eucalyptus urophylla × E. grandis

    Institute of Scientific and Technical Information of China (English)

    周翠鸣; 黄玉清; 顾大形; 赵平; 张德楠; 姚月锋

    2016-01-01

    Large number of Eucalyptus urophylla × E. grandis plantations have been planted in the southern area of Chi-na, especially in Guangxi Zhuang Autonomous Region in the recent years. The influence of water use efficiency in sus-tainable forest development and water resources management has been receiving increasing attention. Therefore, under- standing the water use characteristics is important. The Granier thermal dissipation probe method ( TDP ) is commonly used to monitor tree trunk flow. The sap flow density ( SFD) was monitored in four years E. urophylla × E. grandis plan-tation for one and a half years by Granier TDP at Guangxi Huangmian forest. The change in regularity of SFD, the SFD in trees of different diameters at breast height and the relationship between the SFD and the environmental factors were studied. The results showed that average daily SFD was 830. 1 L . m-2 . d-1 , and the maximum value did not exceed 2 000 L.m-2 .d-1 , when compared with similar studies, these results were relatively low. Because tree trunk was the main part of the plant for water transport, it was necessary to analyze the tree trunk sap flow density( SFD) change at about different diameters at breast height of E. urophylla × E. grandis. There was a positive correlation between SFD and diameter. The SFD was similar when the DBH (diameter at breast height) were in the same diameter class. The SFD varied from tree to tree with different values of maximum and minimum SFD ( 1 300 L . m-2 . d-1 at most ) . This was mainly caused by the different water absorbing capacities of trees. Many studies showed that photosynthetic active radia-tion and vapor pressure deficit( VPD) were the main factors of tree canopy transpiration. The SFD and VPD, photosyn-thetic active radiation ( PAR) displayed similar trend over the study period and exhibited a unimodal curve. The value of SFD was higher in summer and fall, and lower in spring and winter. The relation between SFD and PAR showed signifi

  16. Effect of preservation methods of oil palm sap (Elaeis guineensis) on the reproductive indices of male wistar rats.

    Science.gov (United States)

    Ikegwu, Theophilus Maduabuchukwu; Okafor, Gabriel Ifeanyi; Ochiogu, Izuchukwu Shedrack

    2014-12-01

    Thirty male Wistar rats, split into five groups of six rats each, were administered different forms of oil palm tree (Elaeis guineensis) sap samples by gavage based on 1.5% of their weekly body weights. Group 1 which served as control received only water, group 2 received pasteurized palm sap (PPS), group 3 received market palm wine (MPW), group 4 received frozen palm sap (FPS), whereas group 5 received fresh palm sap (FrPS). Chemical composition of the sap samples was determined. Normal feed and water were fed ad libitum. After 2 months of treatment, each male rat group was allowed 7 days to mate with six female Wistar rats. Thereafter, blood and epididymal samples were collected for testosterone assay and sperm count, respectively, before they were humanely sacrificed and testicular tissues taken for testicular histology. Litter weight and size of the pups produced by the females of each group were determined at birth. The sap samples contained carbohydrate (0.01-11.71%), protein (1.56-1.95%), ash (0.22-0.35%), moisture (92.55-98.24%), and alcohol (0.26-3.50%). PPS-treated rat group had significantly (P<.05) decreased sperm count (42.60±23.64×10(6)), abnormal increase in testosterone level, and necrosis in the histology of the testes with reduced spermatogenetic activity, compared with other treatment groups. The female rats crossed with male rats fed on FrPS or FPS produced the highest number of pups followed by the control group. This study demonstrated that the intake of FrPS improved fertility in male animals, but its administration for a long period led to necrotic changes in the testes, whereas pasteurization of palm sap, impacted negatively on the reproductive indices of male animals.

  17. 喀斯特区不同生境中云南鼠刺树干液流研究%Stem sap flow of Itea yunnanensis at different habitats in karst region

    Institute of Scientific and Technical Information of China (English)

    杨瑞; 肖卫平; 喻理飞

    2011-01-01

    以喀斯特区不同生境中云南鼠刺为研究对象,在“土壤—植物—大气”连续体中,利用热扩散式液流探针(TDP)测定方法,在树冠相似、决定树冠蒸腾的气候因子一致条件下,通过观测树干液流的变化,揭示喀斯特区不同生境中水分变化规律.对雨后连续3个晴天云南鼠刺树干液流进行观测研究,结果表明:1)在石面、石沟、土面3种不同生境中,树干液流速率日变化基本一致,呈不规则的峰形曲线,总体上呈昼高夜低的变化趋势,且日液流速率最大值出现在10:00-14:00之间.2)云南鼠刺树干液流变化因生境类型而不同,石面生境中树干液流速率差异最大、土面次之、石沟不明显,反映出了喀斯特区3种不同生境中水分异质程度的差异.3)在3种生境中平均树干液流速率表现为石面>石沟>土面,且随时间增长而提高,变异系数整体上呈增加趋势,反映出了3种生境中石面生境具有更强水分传导和提高水分效率能力,石沟其次,土面最弱.%Itea yunnanensis at different habitats were taken as the study object in karst region. By using thermal dissipation proble (TDP) measurement method, under the same conditions such as similar crown and climatic factors which determine crown transpiration, the stem sap flow velocity of Itea yunnanensis was measured to reveal the rules of water variation at different habitats in karst region. By observing the fluid flow of Itea yunnanensis on three consecutive sunny days after rain, results revealed that the stem sap flow velocity varied consistently in one day in different habitats, stone face, gully and soil surface. Probably the peak was irregular-shaped curve, and the trend occurred that the sap flow velocity was high in daylight while low at night, and it reached climax during 10;00 to 14;00. The fluid flow velocity of Itea yunnanensis varied in different habitat types. The highest variation was in the stone face, followed

  18. Sap-flow measurement and scale transferring from sample trees to entire forest stand of Populus euphratica in desert riparian forest in extreme arid region

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Understanding how the transpiration of this vegetation type responds to environmental stress is important for determining the wa-ter-balance dynamics of the riparian ecosystem threatened by groundwater depletion. Transpiration and sap flow were measured using the heat-pulse technique. The results were then projected up to the stand level to investigate the stand’s water-use in relation to climate forcing in the desert riparian forest in an extreme arid region. This study took place from April through October 2003 and from May through October 2004. The experimental site was selected in the Populus euphratica Forest Reserve (101o10’ E, 41o59’ N) in Ejina county, in the lower Heihe River basin, China. The sapwood area was used as a scalar to extrapolate the stand-water consumption from the whole trees’ water consumption measured by the heat-pulse velocity recorder (HPVR). Scale transferring from a series of individual trees to a stand was done according to the existing natural variations between trees under given environmental conditions. The application of the biometric parameters available from individual tree and stand levels was proved suitable for this purpose. A significant correlation between the sapwood area and tree diameter at breast height (DBH) was found. The prediction model is well fitted by the power model. On the basis of the prediction model, the sapwood area can be cal-culated by DBH. The sap-flow density can then be used to extrapolate the stand-water use by means of a series of mathematical models.

  19. 21 CFR 133.186 - Sap sago cheese.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Sap sago cheese. 133.186 Section 133.186 Food and... Products § 133.186 Sap sago cheese. (a) Description. (1) Sap sago cheese is the food prepared by the... method described in § 133.5. Sap sago cheese is not less than 5 months old. (2) One or more of the dairy...

  20. Characteristics of sap flow of east and west trunks of Haloxylon ammodendron in Minqin oasis-desert ecotone and correlation analyses%民勤绿洲荒漠过渡带梭梭东、西方位树干液流特征及相关性分析

    Institute of Scientific and Technical Information of China (English)

    张晓艳; 褚建民; 孟平; 姚增旺; 王鹤松; 姜生秀

    2016-01-01

    flow rate of east and west trunks of Haloxylon ammodendron ( C. A. Mey.) Bunge in Minqin oasis-desert ecotone was continuously determined by Grainer thermal diffusion probe method ( TDP) from June to November, and related environmental factors were determined simultaneously. On the basis, diurnal change of sap flow rate of east and west trunks on sunny, cloudy and rainy days and changes of sap flow rate of east and west trunks and environmental factors during experimental period were analyzed, and correlations between sap flow rate of east and west trunks and correlations of them with some environmental factors in different weather and time scales were analyzed. The results show that during vigorous growth period ( from June to August ) , diurnal change of sap flow rate of east and west trunks of H. ammodendron on sunny day both appears obviously“broad peak type” curve. During whole observation period, there is a certain difference in trunk sap flow rate in different weather, and also a certain difference in sap flow rate between east and west trunks and their difference in the nighttime is more obvious than that in the daytime. On the whole, sap flow rate of east trunk is higher than that of west trunk. The correlation analysis results show that there are extremely significantly positive correlations between sap flow rate of east and west trunks of H. ammodendron in different weather and time scales, their correlation coefficients are all above 0. 90 with a little difference. On the whole, correlation between sap flow rate of east and west trunks on sunny day is higher than that on cloudy and rainy days, and that in day scale is the strongest. Correlation of sap flow rate of east and west trunks with environmental factors on sunny day is higher than that on cloudy and rainy days, and that in hour scale is higher than that in day scale. Correlation of sap flow rate of west trunk with environmental factors is slightly higher than that of east trunk, meaning that

  1. On SAP-rings

    OpenAIRE

    Zhixiang, Wu

    2006-01-01

    The rings whose simple right modules are absolutely pure are called right $SAP$-rings. We give a new characterization of right $SAP$ rings, right $V$ rings, and von Neumann regular rings. We also obtain a new decomposition theory of right selfinjective von Neumann regular rings. The relationships between $SAP$-rings, $V$-rings, and von Neumann regular rings are explored. Some recent results obtained by Faith are generalized and the results of Wu-Xia are strengthened.

  2. Characters of Sap Flow of Lilium and Its Relations with Environment Factors%百合生长期茎流特征及其与环境因子的关系

    Institute of Scientific and Technical Information of China (English)

    贾文杰; 马璐琳; 丁鲲; 崔光芬; 吴丽芳; 王祥宁; 王继华

    2012-01-01

    以百合Oriental-Trumpet系列中的罗宾娜为实验材料,在监测环境因子的基础上,用包裹式茎流仪探头对其生长期茎流进行测定研究,明确百合生长期内的茎流和耗水量变化规律.结果表明:(1)百合158 d生长期中,总茎流量为7 289.30 g,平均日茎流量为46.13 g,其中抽茎期、现蕾期、花期、果期和果后期的总茎流量分别为1 862.00、3.197.80、710.50、1 438.30和116.70 g,日均茎流量分别为62.97、72.68、54.65、30.60和4.67 g,不同生长时期百合日茎流速率有明显变化.(2)光辐射和大气温度是影响百合生长周期茎流量的主要环境因子,且光辐射、空气温度与茎流速率呈正相关,而与空气相对湿度呈负相关.(3)阴雨天茎流量和日茎流速率明显小于晴天.该研究为百合水分代谢模型的建立及现代化精准节水百合种植模式的研究奠定了理论基础,对于选择合适的百合节水栽培模式具有重要意义.%The sap flow of cultivar Oriental-Trumpet hybrids Lilium "Robanna" studied with packaged sap flow system,basis on monitoring environment factors. The results of statistical analysis indicated that during the periods of growth of Lilium (158 days) ,the total capacity of sap flow was 7 289. 30 g,46. 13 g per day. Among the periods of stooling stage, squaring stage, flowering stage, fruiting stage and post fruiting stage,sap flows were 1 862.00 g,3 197.80 g,710. 50 g,l 438.30 g, 116. 70 g and averages were 62. 97 g, 72. 68 g,54. 65 g,30. 60 g,4. 67 g,respectively. Sap flow rate was obviously different in the different periods of growth of Lilium. The radiation and temperature were major factors affecting sap flow. Sap flow rate was positively correlated with radiation and temperature,negatively correlated with relatively humidity. Sap flow and Sap flow rate in rainy days and cloudy are lower than that in sunny days. This research establish the theoretical foundation of water metabolism model and water

  3. Very low dose gamma irradiation stimulates gaseous exchange and carboxylation efficiency, but inhibits vascular sap flow in groundnut (Arachis hypogaea L.).

    Science.gov (United States)

    Ahuja, Sumedha; Singh, Bhupinder; Gupta, Vijay Kumar; Singhal, R K; Venu Babu, P

    2014-02-01

    An experiment was carried out to determine the effect of low dose gamma radiation on germination, plant growth, nitrogen and carbon fixation and carbon flow and release characteristics of groundnut. Dry seeds of groundnut variety Trombay groundnut 37A (TG 37A), a radio mutant type developed by Bhabha Atomic Research Centre (BARC), Mumbai, India, were subjected to the pre-sowing treatment of gamma radiation within low to high dose physiological range, i.e., 0.0, 0.0082, 0.0164. 0.0328, 0.0656, 0.1312, 5, 25, 100, 500 Gray (Gy) from a cobalt source ((60)Co). Observations were recorded for the radiation effect on percentage germination, vigour, gas exchange attributes such as photosynthetic rate, stomatal conductance and transpiration rate, chlorophyll content, root exudation in terms of (14)C release, vascular sap flow rate and activities of rate defining carbon and nitrogen assimilating enzymes such as ribulose-1,5-bisphosphate carboxylase (rubisco) and nitrate reductase (NR). Seed germination was increased by 10-25% at the lower doses up to 5 Gy while the improvement in plant vigour in the same dose range was much higher (22-84%) than the unirradiated control. For radiation exposure above 5 Gy, a dose-dependent decline in germination and plant vigour was measured. No significant effect was observed on the photosynthesis at radiation exposure below 5 Gy but above 5 Gy dose there was a decline in the photosynthetic rate. Stomatal conductance and transpiration rate, however, were only inhibited at a high dose of 500 Gy. Leaf rubisco activity and NR activities remained unaffected at all the investigated doses of gamma irradiation. Mean root exudation and sap flow rate of the irradiated plants, irrespective of the dose, was reduced over the unirradiated control more so in a dose-dependent manner. Results indicated that a very low dose of gamma radiation, in centigray to gray range, did not pose any threat and in fact stimulated metabolic functions in such a way to aid

  4. Numerical methods for turbulent flow

    Science.gov (United States)

    Turner, James C., Jr.

    1988-01-01

    It has generally become accepted that the Navier-Strokes equations predict the dynamic behavior of turbulent as well as laminar flows of a fluid at a point in space away form a discontinuity such as a shock wave. Turbulence is also closely related to the phenomena of non-uniqueness of solutions of the Navier-Strokes equations. These second order, nonlinear partial differential equations can be solved analytically for only a few simple flows. Turbulent flow fields are much to complex to lend themselves to these few analytical methods. Numerical methods, therefore, offer the only possibility of achieving a solution of turbulent flow equations. In spite of recent advances in computer technology, the direct solution, by discrete methods, of the Navier-Strokes equations for turbulent flow fields is today, and in the foreseeable future, impossible. Thus the only economically feasible way to solve practical turbulent flow problems numerically is to use statistically averaged equations governing mean-flow quantities. The objective is to study some recent developments relating to the use of numerical methods to study turbulent flow.

  5. Xylem sap proteomics.

    Science.gov (United States)

    de Bernonville, Thomas Dugé; Albenne, Cécile; Arlat, Matthieu; Hoffmann, Laurent; Lauber, Emmanuelle; Jamet, Elisabeth

    2014-01-01

    Proteomic analysis of xylem sap has recently become a major field of interest to understand several biological questions related to plant development and responses to environmental clues. The xylem sap appears as a dynamic fluid undergoing changes in its proteome upon abiotic and biotic stresses. Unlike cell compartments which are amenable to purification in sufficient amount prior to proteomic analysis, the xylem sap has to be collected in particular conditions to avoid contamination by intracellular proteins and to obtain enough material. A model plant like Arabidopsis thaliana is not suitable for such an analysis because efficient harvesting of xylem sap is difficult. The analysis of the xylem sap proteome also requires specific procedures to concentrate proteins and to focus on proteins predicted to be secreted. Indeed, xylem sap proteins appear to be synthesized and secreted in the root stele or to originate from dying differentiated xylem cells. This chapter describes protocols to collect xylem sap from Brassica species and to prepare total and N-glycoprotein extracts for identification of proteins by mass spectrometry analyses and bioinformatics.

  6. SAP R/3系统客户化接口程序的开发方法及实现%Method and implementation of SAP R/3 system's customized interface program

    Institute of Scientific and Technical Information of China (English)

    关宇平

    2007-01-01

    对应用SAP ERP系统中的ABAP开发语言、RFC、BAPI、BDC等技术实现SAP客户化接口程序的开发方法进行了探讨,通过案例展示了相关技术在实践中的具体应用,为SAP ERP的用户及从事ABAP开发的人员进行SAP客户化接口需求分析及开发提供指导作用.

  7. Aplikace SAP HANA

    OpenAIRE

    2014-01-01

    The work is dedicated to analysis of data using ICT. It is clear that the classical way of dealing with the data is not satisfactory. Therefore, the new number of tools that changing the view of working with data has occured. An example is the SAP system HANA. The main aim of this thesis is to introduce SAP HANA platform as a tool for analytical processing of large amounts of data (especially in wide area-based marketing and customer relationship management) on the example SAP Customer Engage...

  8. SAP Sector Develops Rapidly

    Institute of Scientific and Technical Information of China (English)

    Zheng Chengwang

    2007-01-01

    @@ Stable demand growth internationally Super absorbent polymers (SAP) feature high water absorption, high water retention, rapid water absorption, great expanding power,strong thickening, strong anchoring and excellent elasticity.

  9. Fluxo de seiva pelo método do balanço de calor: base teórica, qualidade das medidas e aspectos práticos Sap flow by heat balance method: theoretical basis, data quality and practical aspects

    Directory of Open Access Journals (Sweden)

    Fábio Ricardo Marin

    2008-01-01

    Full Text Available O método do balanço de calor representa uma técnica importante para estudos sobre fisiologia vegetal, agrometeorologia e irrigação. Sua aplicação tem aumentado nos últimos anos em decorrência da maior facilidade de importação de material e equipamentos e do uso mais disseminado dos sistemas automáticos de aquisição de dados. Avanços importantes em diversas áreas de pesquisa têm sido alcançados com a possibilidade de se quantificar o consumo hídrico em plantas isoladas em diferentes escalas de tempo. Com base na teoria do método, esta revisão tem como objetivo apresentar e discutir os procedimentos de instalação, manutenção e de análise e processamento dos dados com vistas ao uso mais adequado da técnica e à obtenção de dados mais confiáveis e coerentes. Aspectos relacionados à influência das condições ambientais no funcionamento do sensor são abordados; são também discutidas diversas recomendações práticas observadas na literatura disponível. O grande número e a diversidade de procedimentos que envolvem a instalação dos sensores, sua manutenção em condições de campo e a análise dos dados conferem ao método grande aplicação na experimentação científica. Entretanto, o uso do método de balanço de calor em larga escala parece inadequado devido à dificuldade de correta operação, o que facilmente compromete a qualidade das medidas.The stem heat balance method has become an important technique in plant physiology, agrometeorology and irrigation science. Its application has increased in the last years due to the development of less expensive automatic data acquisition systems that are widespread. Important advances in several research areas have been reached by quantifying the water consumption by isolated plants in different temporal scales. Based on the theory of the method, this review aims to present and discuss the procedures of installation and maintenance, and data analysis and

  10. SAP HANA cookbook

    CERN Document Server

    Chandrasekhar

    2013-01-01

    An easy-to-understand guide, covering topics using practical scenarios and live examples, and answering all possible questions.If you are a solution architect, developer, modeler, sales leader, business transformation managers, directors, COO, or CIO; this book is perfect for you.If you are interested in other technologies and want to jump-start into SAP, this book gives you the chance to learn SAP HANA. Basic knowledge of RDBMS concepts enough is to get you started.

  11. Sap flow for beech (Fagus sylvatica L.) in a natural and a managed forest-effect of spatial heterogeneity

    DEFF Research Database (Denmark)

    Dalsgaard, Lise; Mikkelsen, Teis Nørgaard; Bastrup-Birk, Annemarie

    2011-01-01

    using non-linear statistical methods with air vapour pressure deficit (D, hPa) and global radiation (R-g, J m(-2) day(-1)), along with constraints imposed by reductions in soil water content (SWC). SWC was measured as volumetric % using time domain reflectometry. The daily integrated J(s) (J......(s-sum) in the outer 20 mm of the xylem in NAT was lower than that in MAN and the rate of decline in J(s) with xylem depth was less in NAT than in MAN. In MAN, J(s-sum) in deep and outer xylem was negatively affected at low soil moisture availability; in NAT, this was the case for only the outer xylem indicating...

  12. Software development on the SAP HANA platform

    CERN Document Server

    Walker, Mark

    2013-01-01

    Software Development on the SAP HANA Platform is a general tutorial guide to SAP HANA.This book is written for beginners to the SAP HANA platform. No knowledge of SAP HANA is necessary to start using this book.

  13. Maximum sustainable xylem sap tensions in Rhododendron and other species.

    Science.gov (United States)

    Crombie, D S; Milburn, J A; Hipkins, M F

    1985-01-01

    The acoustic technique was used in conjunction with the pressure chamber to determine the tensions causing cavitation of xylem sap in leaves of five woody angiosperms (Acer pseudoplatanus L., Alnus glutinosa L. Gaertn., Eucalyptus globulus Labill., Fraxinus excelsior L. and Rhododendron ponticum L.) and three species of herbs (Lycopersicum esculentum Mill., Plantago major L. and Ricinus communis L.). The results showed leaves of most species to suffer considerably from cavitation at sap tensions of 1.6-3 MPa. Two of the herbs, Lycopersicum and Ricinus, cavitated extensively at sap tensions below 1 MPa. Additional evidence is presented that clicks, detected by acoustic amplification, are caused by cavitation of sap in the xylem conduits. A rapid method is suggested for the determination of sap tensions in cavitating leaves and which is suitable for surveys of the critical sap tension in a large number of species.

  14. Response of Sap Flow and Leaf Water Potential for Greenhouse Tomato under Moisture Stress%不同水分胁迫条件下温室番茄茎流和叶片水势的反应

    Institute of Scientific and Technical Information of China (English)

    杨再强; 张婷华; 李永秀; 彭晓丹; 周志龙; 朱凯; 赵翔

    2012-01-01

    To understand the effects of different moisture stress on sap flow and leaf potential of tomato in greenhouse, authors conducted the experiments under three water treatments, including normal water supply (T1 ) , light water stress treatment (T2) and severe water stress treatment ( T3 ) ,for tomato variety "Jingfen 2' . The results showed that the daily variation of sap flow of tomato plant occurred as a bimodal curve under Tl and T2 in sunny days, and the bottom point was at 12; 00 in the noon with the stoma closed. The sap flow of tomato changed slightly under Tl and T2 in cloudy days. The transpiration changed a lot under different water stresses. Transpiration became less with more serious water stress. The difference between different transpiration decreased gradually with time extension after irrigation, leaf water potential decreased was well, with T1 > T2 > T3. In addition, solar radiation, air temperature and relative air humidity (RH) was the main meteorological factors affecting sap flow rate of the tomato by correlative analysis. The results indicated that there was a positive correlation between the sap flow and solar radiation, air temperature and soil moisture. On the contrary, there was a negative correlation between the sap flow and leaf water potential and the relative air humidity (RH).%以番茄“金粉2号”(Jingfen 2)品种为试材,设正常灌溉(T1)、轻度胁迫(T2)和重度胁迫(T3)3个土壤水分处理,观测不同土壤水分条件下番茄植株的茎流速率和叶片水势.结果表明,番茄植株茎流速率日变化呈现明显的规律性,晴天,T1和T2的番茄茎流速率呈明显的双峰曲线,中午12:00左右气孔关闭,茎流速率出现低谷.阴天,T1和T2处理番茄茎流日变化趋势总体较为平缓.不同水分处理下番茄的蒸腾量差异明显,水分胁迫处理的番茄蒸腾量均小于正常灌溉,土壤水分胁迫程度越严重,日蒸腾量越低.随着水分处理天数的增加,不同灌溉

  15. Variation in the radial patterns of sap flux density in pubescent oak (Quercus pubescens) and its implications for tree and stand transpiration measurements.

    Science.gov (United States)

    Poyatos, Rafael; Cermák, Jan; Llorens, Pilar

    2007-04-01

    Radial variation in sap flux density across the sapwood was assessed by the heat field deformation method in several trees of Quercus pubescens Wild., a ring-porous species. Sapwood depths were delimited by identifying the point of zero flow in radial patterns of sap flow, yielding tree sapwood areas that were 1.5-2 times larger than assumed based on visual examinations of wood cores. The patterns of sap flow varied both among trees and diurnally. Rates of sap flow were higher close to the cambium, although there was a significant contribution from the inner sapwood, which was greater (up to 60% of total flow) during the early morning and late in the day. Accordingly, the normalized difference between outer and inner sapwood flow was stable during the middle of the day, but showed a general decline in the afternoon. The distribution of sap flux density across the sapwood allowed us to derive correction coefficients for single-point heat dissipation sap flow measurements. We used daytime-averaged coefficients that depended on the particular shape of the radial profile and ranged between 0.45 and 1.28. Stand transpiration calculated using the new method of estimating sapwood areas and the radial correction coefficients was similar to (Year 2003), or about 25% higher than (Year 2004), previous uncorrected values, and was 20-30% of reference evapotranspiration. We demonstrated how inaccuracies in determining sapwood depths and mean sap flux density across the sapwood of ring-porous species could affect tree and stand transpiration estimates.

  16. Improving sap flux density measurements by correctly determining thermal diffusivity, differentiating between bound and unbound water.

    Science.gov (United States)

    Vandegehuchte, Maurits W; Steppe, Kathy

    2012-07-01

    Several heat-based sap flow methods, such as the heat field deformation method and the heat ratio method, include the thermal diffusivity D of the sapwood as a crucial parameter. Despite its importance, little attention has been paid to determine D in a plant physiological context. Therefore, D is mostly set as a constant, calculated during zero flow conditions or from a method of mixtures, taking into account wood density and moisture content. In this latter method, however, the meaning of the moisture content is misinterpreted, making it theoretically incorrect for D calculations in sapwood. A correction to this method, which includes the correct application of the moisture content, is proposed. This correction was tested for European and American beech and Eucalyptus caliginosa Blakely & McKie. Depending on the dry wood density and moisture content, the original approach over- or underestimates D and, hence, sap flux density by 10% and more.

  17. Effects of climatic conditions on radial growth and sap-flow along an elevation gradient in an inner-alpine dry valley

    Science.gov (United States)

    Obojes, Nikolaus; Newesely, Christian; Bertoldi, Giacomo; Tassser, Erich; Oberhuber, Walter; Mayr, Stefan; Tappeiner, Ulrike

    2016-04-01

    Water availability in mountain forests might change in the future due to rising temperatures and changing precipitation patterns, affecting tree water relations and growth conditions. Changing temperature and precipitation along an elevation gradient in an inner-alpine dry valley in South Tyrol-Italy were used to investigate possible effects of climate change on the transpiration and growth of European Larch (Larix decidua). Stem circumference variation of European Larch was measured for 4 years (2012-2015) with automatic band dendrometers and sap flow for 2 years (2013-2014) with trunk heat balance sensors at 3 sites at elevations of 1115 m, 1715 m, and 1990 m above sea level at a SE-exposed slope. During the first two, rather dry, years, transpiration and stem circumference were reduced during dry periods of one to three weeks at the two lower but not at the highest site. As a consequence, overall yearly radial growth was largest at the highest site in those two years. In 2014, with very high precipitation and colder summer temperatures no correlation of elevation, transpiration, and radial growth was observed. In 2015, with a dry and hot summer, initially high growth rates were strongly reduced after the end of May at the two lower sites. Overall the radial growth of Larix decidua seems to be limited by water scarcity up to an elevation of more than 1700 m a.s.l. in our study area except for unusually wet years. Our 4-year measurements were confirmed by dendro-climatic analysis of stem cores taken at five sites (the three original ones plus two additional sites at 1070 and at the forest line at 2250m) covering the last 50 to 150 years. Year ring widths were lower and highly correlated to precipitation at the lowest sites, and overall highest at the 1990 m site. Our results show that the growth of Larix decidua, which is often considered as more drought resistant than e.g. Picea abies, is limited by water availability at dry conditions in the Alps which might

  18. 7 CFR 1437.107 - Maple sap.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 10 2010-01-01 2010-01-01 false Maple sap. 1437.107 Section 1437.107 Agriculture... Yield Coverage Using Actual Production History § 1437.107 Maple sap. (a) NAP assistance for maple sap is limited to maple sap produced on private property for sale as sap or syrup. Eligible maple sap must be...

  19. Measurement of respirable superabsorbent polyacrylate (SAP) dust by ethanol derivatization using gas chromatography-mass spectrometry (GC-MS) detection.

    Science.gov (United States)

    McCormack, Paul; Lemmo, John S; Macomber, Margaret; Holcomb, Mark L; Lieckfield, Robert

    2011-04-01

    Superabsorbent polyacrylate (SAP) is an important industrial chemical manufactured primarily as sodium polyacrylate but occasionally as potassium salt. It has many applications owing to its intrinsic physical property of very high water absorption, which can be more than 100 times it own weight. SAP is commonly used in disposable diapers and feminine hygiene products and is known by a number of synonyms-sodium polyacrylate, superabsorbent polyacrylate (SAP), polyacrylate absorbent (PA), and superabsorbent material (SAM). Germany and The Netherlands have adopted a nonbinding scientific guideline value 0.05 mg/m³ (8-hr time-weighted average, TWA) as the maximum allowable workplace concentration for the respirable dust of SAP (polyacrylate dust collected on filter cassettes in the workplace environment. This method is an alternative to the commonly used sodium-based method, which is limited owing to potential interference by other sources of sodium from the workplace and laboratory environments. The alcohol derivatization method effectively eliminates sodium interference from several classes of sodium compounds, as shown by their purposeful introduction at two and six times the equivalent amount of SAP present in reference samples. The accuracy of the method, as determined by comparison with sodium analysis of known reference samples, was greater than 80% over the study range of 5-50 μg of SAP dust. The lower reporting limit of the method is 3.0 μg of SAP per sample, which is equivalent to 3 (μg/m³) for an 8-hr sampling period at the recommended flow rate of 2.2 L/min.

  20. Monitoring and modelling of soil–plant interactions: the joint use of ERT, sap flow and Eddy Covariance data to characterize the volume of an orange tree root zone

    Directory of Open Access Journals (Sweden)

    G. Cassiani

    2014-12-01

    Full Text Available Mass and energy exchanges between soil, plants and atmosphere control a number of key environmental processes involving hydrology, biota and climate. The understanding of these exchanges also play a critical role for practical purposes e.g. in precision agriculture. In this paper we present a methodology based on coupling innovative data collection and models in order to obtain quantitative estimates of the key parameters of such complex flow system. In particular we propose the use of hydro-geophysical monitoring via 4-D Electrical Resistivity Tomography (ERT in conjunction with measurements of plant transpiration via sap flow and evapotranspiration from Eddy Covariance (EC. This abundance of data is fed to a spatially distributed soil model in order to characterize the distribution of active roots. We conducted experiments in an orange orchard in Eastern Sicily (Italy, characterized by the typical Mediterranean semi-arid climate. The subsoil dynamics, particularly influenced by irrigation and root uptake, were characterized mainly by the ERT setup, consisting of 48 buried electrodes on 4 instrumented micro boreholes (about 1.2 m deep placed at the corners of a square (about 1.3 m in side surrounding the orange tree, plus 24 mini-electrodes on the surface spaced 0.1 m on a square grid. During the monitoring, we collected repeated ERT and TDR soil moisture measurements, soil water samples, sap flow measurements from the orange tree and EC data. We conducted a laboratory calibration of the soil electrical properties as a function of moisture content and pore water electrical conductivity. Irrigation, precipitation, sap flow and ET data are available allowing knowledge of the system's long term forcing conditions on the system. This information was used to calibrate a 1-D Richards' equation model representing the dynamics of the volume monitored via 3-D ERT. Information on the soil hydraulic properties was collected from laboratory and field

  1. Antidiarrhoeal Activity of Musa paradisiaca Sap in Wistar Rats.

    Science.gov (United States)

    Yakubu, Musa T; Nurudeen, Quadri O; Salimon, Saoban S; Yakubu, Monsurat O; Jimoh, Rukayat O; Nafiu, Mikhail O; Akanji, Musbau A; Oladiji, Adenike T; Williams, Felicia E

    2015-01-01

    The folkloric claim of Musa paradisiaca sap in the management of diarrhoea is yet to be substantiated or refuted with scientific data. Therefore, the aim of the current study was to screen the sap of M. paradisiaca for both its secondary metabolites and antidiarrhoeal activity at 0.25, 0.50, and 1.00 mL in rats. Secondary metabolites were screened using standard methods while the antidiarrhoeal activity was done by adopting the castor oil-induced diarrhoeal, castor oil-induced enteropooling, and gastrointestinal motility models. The sap contained flavonoids, phenolics, saponins, alkaloids, tannins, and steroids while cardiac glycosides, anthraquinones, triterpenes, cardenolides, and dienolides were not detected. In the castor oil-induced diarrhoeal model, the sap significantly (P sap were accompanied by increase in inhibition of intestinal fluid content in the enteropooling model. The sap decreased the charcoal meal transit in the gastrointestinal motility model. In all the models, the 1.00 mL of the sap produced changes that compared well with the reference drugs. Overall, the antidiarrhoeal activity of Musa paradisiaca sap attributed to the presence of alkaloids, phenolics, flavonoids, and/or saponins which may involve, among others, enhancing fluid and electrolyte absorption through de novo synthesis of the sodium potassium ATPase and/or reduced nitric oxide levels.

  2. When do Acacia mellifera trees use water? Responses of sap velocity to soil water availability, vapour pressure deficit and global radiation.

    Science.gov (United States)

    de Blécourt, Marleen; Thomsen, Simon; Gröngröft, Alexander; Eschenbach, Annette

    2017-04-01

    Acacia mellifera (multi-stem deciduous tree) is one of the dominant woody species responsible for bush encroachment in southern African savannahs. However, very little is known on water use, transpiration or xylem sap flow of A. mellifera. We analyzed the responses of sap velocity in A. mellifera to soil moisture, vapour pressure deficit and global radiation. This knowledge is necessary to improve hydrological modelling and will as such contribute to our understanding of the impacts of bush encroachment in (semi) arid savannahs on the soil water balance. We monitored sap velocities at two sites that differed in tree density in a semi-arid thornbush savannah in central Namibia (mean annual precipitation = 346 mm). Sap velocities were derived using the Heat Ratio Method. Measurements were done in four periods of 3-4 months between November 2014 and September 2016. The measurement periods covered the transitions between the dry and rainy season and vice versa, and the dry season. In two of these periods we did measurements at all stems of three trees per site (a total of 17-19 stems), while in the other two periods sap velocities were measured on one stem per tree for six to eight trees per site. The study was done in the framework of SASSCAL (Southern African Science Service Centre for Climate Change and Adaptive Land Management) granted by the German Federal Ministry of Education and Research (BMBF). Preliminary results indicate that the day-to-day fluctuations in cumulative daily sap velocity showed a three-phase interaction with soil water tension (minimum soil water tension of four sensors to 1-m depth). Phase I: At soil water tension radiation. Phase II: At soil water tensions between pF 2.5 and pF 3.2, sap velocities were negatively related to soil water tension. Phase III: At soil water tensions > pF 3.2 no sap flow could be detected.

  3. FLOW-Methode - Methodenbeschreibung zur Anwendung von FLOW

    CERN Document Server

    Stapel, Kai

    2012-01-01

    Information of many kinds is flowing in software projects and organizations. Requirements have to flow from the customer to the developers. Testers need to know the requirements as well. Boundary conditions and design decisions have to be at the right place at the right time. Information flow analysis with FLOW facilitates modeling of mode and route of the flow of information and experience independent of the development methodology. Experience often acts as a control factor, because experienced developers can process and route information more efficiently. Therefore, experience needs to be at the right place at the right time, too. However, most valuable experiences never get documented. Since information and experience is flowing in agile as well as in traditional environments, the FLOW method does not distinguish between agile and traditional, but only between how the flows are shaped. ---- In Softwareprojekten flie{\\ss}en vielerlei Informationen. Anforderungen m\\"ussen vom Kunden zu den Entwicklern gelang...

  4. Research of transpiration and evapotranspiration from a grapevine canopy combining the sap flow and eddy covariance techniques%基于树干液流及涡动相关技术的葡萄冠层蒸腾及蒸散发特征研究

    Institute of Scientific and Technical Information of China (English)

    白岩; 朱高峰; 张琨; 马婷

    2015-01-01

    针对西北干旱区绿洲经济作物葡萄树冠层蒸腾及蒸散发特征的相关问题,在甘肃省敦煌市南湖绿洲开展无核白葡萄树液流速率及蒸散发观测试验,采用基于热平衡原理的包裹式茎流计,详细分析了典型生长季7—9月份葡萄树蒸腾耗水规律,使用“单位叶面积上的平均液流速率SF×叶面积指数LAI”的方法,实现了从单株到林分冠层蒸腾的尺度扩展,并通过与涡动相关技术所测蒸散发数据对比,详细研究了葡萄地冠层蒸腾及蒸散发规律。结果表明:典型生长季中葡萄树液流速率日变化为单峰型曲线,日均耗水量从2.76 kg到10 kg不等,胸径越大的葡萄树日均耗水量越大;冠层蒸腾及蒸散发日变化曲线亦为单峰型,白天8:00—12:00与17:00—20:00期间,葡萄冠层蒸腾与蒸散发曲线均比较吻合,该时间段葡萄地蒸散发绝大部分来源于葡萄冠层蒸腾,而12:00—17:00之间由于午后太阳辐射强烈土壤蒸发量增加,葡萄蒸散发大于冠层蒸腾;典型生长季3个月中,葡萄冠层蒸腾量的变化范围在1.88—8.12 mm/d之间,日均冠层蒸腾量为6.12 mm/d,蒸散发在1.74 mm/d 至10.78 mm/d之间,日均蒸散发量为7.13 mm/d;日均土壤蒸发量约为1.01 mm/d,只占总蒸散发量的14.2%,日均冠层蒸腾占日均蒸散发的比重达到85.8%,说明该生长阶段冠层蒸散发以作物蒸腾为主。%In agriculture ecosystems, more than 90% of all water input is lost by evapotranspiration ( ET ) . Thus, the accurate measurement of ET and its associated components (i.e., canopy transpiration and soil evaporation) are essential for many agricultural applications, such as irrigation scheduling, drainage, and yield forecasts. In the arid region of northwestern China, water resources are rare and are often the restricting factor for plant production. By comprehensively using the sap flow method and eddy covariance ( EC) technique, the single

  5. A model of heat transfer in sapwood and implications for sap flux density measurements using thermal dissipation probes.

    Science.gov (United States)

    Wullschleger, Stan D; Childs, Kenneth W; King, Anthony W; Hanson, Paul J

    2011-06-01

    A variety of thermal approaches are used to estimate sap flux density in stems of woody plants. Models have proved valuable tools for interpreting the behavior of heat pulse, heat balance and heat field deformation techniques, but have seldom been used to describe heat transfer dynamics for the heat dissipation method. Therefore, to better understand the behavior of heat dissipation probes, a model was developed that takes into account the thermal properties of wood, the physical dimensions and thermal characteristics of the probes, and the conductive and convective heat transfer that occurs due to water flow in the sapwood. Probes were simulated as aluminum tubes 20 mm in length and 2 mm in diameter, whereas sapwood, heartwood and bark each had a density and water fraction that determined their thermal properties. Base simulations assumed a constant sap flux density with sapwood depth and no wounding or physical disruption of xylem beyond the 2 mm diameter hole drilled for probe installation. Simulations across a range of sap flux densities showed that the dimensionless quantity k [defined as (ΔT(m) -ΔT)/ΔT, where ΔT(m) is the temperature differential (ΔT) between the heated and unheated probe under zero-flow conditions] was dependent on the thermal conductivity of the sapwood. The relationship between sap flux density and k was also sensitive to radial gradients in sap flux density and to xylem disruption near the probe. Monte Carlo analysis in which 1000 simulations were conducted while simultaneously varying thermal conductivity and wound diameter revealed that sap flux density and k showed considerable departure from the original calibration equation used with this technique. The departure was greatest for variation in sap flux density typical of ring-porous species. Depending on the specific combination of thermal conductivity and wound diameter, use of the original calibration equation resulted in an 81% under- to 48% overestimation of sap flux density

  6. Effect of flow fluctuations and nonflow on elliptic flow methods

    Energy Technology Data Exchange (ETDEWEB)

    Ollitrault, Jean-Yves; Poskanzer, Arthur M.; Voloshin, Sergei A.

    2009-04-16

    We discuss how the different estimates of elliptic flow are influenced by flow fluctuations and nonflow effects. It is explained why the event-plane method yields estimates between the two-particle correlation methods and the multiparticle correlation methods. It is argued that nonflow effects and fluctuations cannot be disentangled without other assumptions. However, we provide equations where, with reasonable assumptions about fluctuations and nonflow, all measured values of elliptic flow converge to a unique mean v_2,PP elliptic flow in the participant plane and, with a Gaussian assumption on eccentricity fluctuations, can be converted to the mean v_2,RP in the reaction plane. Thus, the 20percent spread in observed elliptic flow measurements from different analysis methods is no longer mysterious.

  7. SAP SE: Autism at Work

    DEFF Research Database (Denmark)

    Pisano, Gary P.; Austin, Robert D.

    2016-01-01

    This case describes SAP's 'Autism at Work' program, which integrates people with autism into the company's workforce. The company has a stated objective of making 1% o its workforce people with autism by 2020. SAP's rationale for the program is based on the belief that 'neurodiversity' contributes...

  8. Nano scale proteomics revealed the presence of regulatory proteins including three FT-Like proteins in phloem and xylem saps from rice.

    Science.gov (United States)

    Aki, Toshihiko; Shigyo, Mikao; Nakano, Ryouhei; Yoneyama, Tadakatsu; Yanagisawa, Shuichi

    2008-05-01

    The main physiological roles of phloem and xylem in higher plants involve the transport of water, nutrients and metabolites. They are also involved, however, in whole plant events including stress responses and long-distance signaling. Phloem and xylem saps therefore include a variety of proteins. In this study, we have performed a shotgun analysis of the proteome of phloem and xylem saps from rice, taking advantage of the complete and available genomic information for this plant. Xylem sap was prepared using the root pressure method, whereas phloem sap was prepared with a unique method with the assistance of planthoppers to ensure the robustness of the detected proteins. The technical difficulties caused by the very limited availability of rice samples were overcome by the use of nano-flow liquid chromatography linked to a mass spectrometer. We identified 118 different proteins and eight different peptides in xylem sap, and 107 different proteins and five different peptides in phloem sap. Signal transduction proteins, putative transcription factors and stress response factors as well as metabolic enzymes were identified in these saps. Interestingly, we found the presence of three TERMINAL FLOWER 1/FLOWERING LOCUS T (FT)-like proteins in phloem sap. The detected FT-like proteins were not rice Hd3a (OsFTL2) itself that acted as a non-cell-autonomous signal for flowering control, but they were members of distinct subfamilies of the FT family with differential expression patterns. These results imply that proteomics on a nano scale is a potent tool for investigation of biological processes in plants.

  9. Fluxo de seiva e fotossíntese em laranjeira 'Natal' com clorose variegada dos citros Sap flow and photosynthesis of 'Natal' sweet orange plants with citrus variegated chlorosis

    Directory of Open Access Journals (Sweden)

    Eduardo Caruso Machado

    2006-06-01

    Full Text Available O objetivo deste trabalho foi avaliar os efeitos da clorose variegada dos citros (CVC, no fluxo de seiva, trocas gasosas e atividade fotoquímica em laranjeira 'Natal', com e sem CVC, em condição de campo. O curso diário do fluxo de seiva, potencial da água na folha, assimilação de CO2, transpiração, condutância estomática e eficiência quântica máxima e efetiva do fotossistema II foram avaliados. O delineamento experimental foi em blocos ao acaso com cinco repetições. O fluxo de seiva foi 1,9 vez superior nas plantas sadias em relação às doentes. Em plantas doentes ocorreu queda de 43, 28 e 33% na assimilação de CO2, condutância estomática e transpiração, respectivamente. As plantas com CVC apresentaram fotoinibição dinâmica. Uma vez que a eficiência quântica efetiva apresentou um padrão de resposta semelhante, durante o dia, em ambos os tratamentos, o efeito protetor da fotorrespiração no aparato fotoquímico em plantas com CVC é discutido. As quedas de assimilação de CO2, transpiração e de fluxo de seiva, nas plantas com CVC, foram decorrentes do menor valor da condutância estomática, possivelmente causado pela colonização dos vasos do xilema pela Xylella fastidiosa.The objective of this work was to evaluate the effects of citrus variegated chlorosis (CVC on sap flow, gas exchanges and photochemical activity in 'Natal' sweet orange plants with and without CVC under field condition. Diurnal courses of sap flow, leaf water potential, CO2 assimilation rate and transpiration, stomatal conductance, potential and effective quantum efficiency of photosystem II were evaluated. The experiment was arranged in a random block design with five repetitions. Healthy plants showed sap flow values around 1.9 times higher than injured ones. Injured plants exhibited reductions of 43, 28 and 33% in CO2 assimilation rate, stomatal conductance and leaf transpiration, respectively. CVC-affected plants showed dynamic

  10. Euphorbia grandicornis Sap Keratouveitis: A Case Report

    Directory of Open Access Journals (Sweden)

    María Gómez-Valcárcel

    2016-02-01

    Full Text Available Purpose: To describe a case of keratouveitis caused by Euphorbia grandicornis sap, that resolved with topic steroids. Methods: We report a case presentation of a patient with keratouveitis. Results: A 70-year-old woman suffered from accidental ocular contact with E. grandicornis sap in her left eye. Two hours after the contact, she attended the clinic due to conjunctival hyperemia and pain. Best-corrected visual acuity (BCVA was 20/25. The toxic conjunctivitis was treated with topical lubricant and steroid. After 24 h, she presented blurred vision. BCVA was 20/80. Toxic keratouveitis was diagnosed. Topical treatment with 1% cyclopentolate t.i.d., 5% sodium chloride, 1.14% dexamethasone phosphate each hour, and 4% sodium hyaluronate each hour was continued. Complete resolution was obtained 1 week later. Euphorbia sap content analysis was performed using dissolvent extraction spectrophotometry. Its contents included flavonoids, alkaloids, phenols and sesquiterpene lactones. Conclusion: Corneal exposure to E. grandicornis sap is a cause of nonvisually threatening keratouveitis when adequately treated with corticosteroids.

  11. Critical factors in the limited occurrence of the Japanese tree sap mite Hericia sanukiensis (Acari: Astigmata: Algophagidae) inhabiting the sap of the oak Quercus acutissima.

    Science.gov (United States)

    Hayashi, Kyohei; Ichikawa, Toshihide; Yasui, Yukio

    2011-08-01

    Hericia sanukiensis (Astigmata: Algophagidae) is a semi-aquatic mite inhabiting fermented sap flux of the Japanese sawtooth oak (Quercus acutissima) and utilizes Nitidulidae (Coleoptera) as the dispersal (phoretic) carrier. Although nitidulid beetles are commonly found in sap flux, the occurrence of H. sanukiensis has been extremely limited to a few trees in Shikoku Island, Kagawa Prefecture, Japan. To elucidate the critical factors limiting the occurrence of this species, we compared several physical and biological characteristics of sap-exudation points, including the structure and temperature of tree trunks, period and abundance of sap exudation, and seasonal occurrence and dispersal behavior of nitidulid beetles between environments with and without mites. During the two consecutive years of field research, we found that only sap-exudation points with obvious tree holes (ringent area >10 cm², depth >10 cm) had sustained mite populations throughout the observation period. In contrast, for the sap-exudation points lacking tree holes, H. sanukiensis temporally (from spring to autumn) colonized only when the sap production was considerably high. Thus, we suggest that the settlement of H. sanukiensis populations requires tree holes as an overwintering habitat. Nitidulid beetles also concentrated in areas with high sap production and did not disperse from such habitats during the sap flow season. This indicates that H. sanukiensis mites may only disperse and colonize new habitats at very limited opportunities, such as drastic habitat deterioration, which may promote the movement of their carrier. Taken together, these findings may explain the limited occurrence of this mite species.

  12. Dynamics of Subauroral Polarization Stream (SAPS) Structures

    Science.gov (United States)

    Sazykin, S. Y.; Coster, A. J.; Huba, J.; Ridley, A. J.; Erickson, P. J.; Foster, J. C.; Baker, J. B. H.; Wolf, R.

    2015-12-01

    The Subauroral Polarization Stream (SAPS) flow structures are narrow ionospheric channels of fast (in excess of 100 m/s) westward drift just outside the equatorward edge of the diffuse aurora in the dusk-to-midnight local time sector. Other terms for this phenomenon include subauroral Ion Drift (SAID) events and Polarization Jets. SAPS structures represent a striking departure from the commonly-used two-cell convection pattern. They are thought to arise from the displacement of the downward region-2 Birkeland currents on the dusk side equatorward of the low-latitude boundary of the auroral oval during times of changing high-latitude convection. In this paper, we will use several event simulations with the SAMI3-RCM numerical model (a self-consistent ionosphere-inner magnetosphere model) and RCM-GITM (a self-consistent model of the ionosphere-thermosphere-inner magnetosphere) to analyze the relative roles of changes in the IMF Bz component, ionospheric electron density depletions, and thermospheric modifications in controlling the dynamics of SAPS. Simulation results will be compared to multi-instrument ionospheric observations.

  13. The Direct Method of Cash Flows.

    Science.gov (United States)

    Bosserman, David C.; Fischer, Mary

    2000-01-01

    Explains to college/university business officers how to comply with Governmental Accounting Standards Board Statements Nos. 34, 35, and 9, which require the direct method of presenting cash flows from operating activities and reconciliation of operating cash flows to operating income by fiscal year 2001. Institutions are urged to begin immediately…

  14. The Direct Method of Cash Flows.

    Science.gov (United States)

    Bosserman, David C.; Fischer, Mary

    2000-01-01

    Explains to college/university business officers how to comply with Governmental Accounting Standards Board Statements Nos. 34, 35, and 9, which require the direct method of presenting cash flows from operating activities and reconciliation of operating cash flows to operating income by fiscal year 2001. Institutions are urged to begin immediately…

  15. Fluorescent multiplex cell flow systems and methods

    KAUST Repository

    Merzaban, Jasmeen

    2017-06-01

    Systems and methods are provided for simultaneously assaying cell adhesion or cell rolling for multiple cell specimens. One embodiment provides a system for assaying adhesion or cell rolling of multiple cell specimens that includes a confocal imaging system containing a parallel plate flow chamber, a pump in fluid communication with the parallel plate flow chamber via a flow chamber inlet line and a cell suspension in fluid communication with the parallel plate flow chamber via a flow chamber outlet line. The system also includes a laser scanning system in electronic communication with the confocal imaging system, and a computer in communication with the confocal imaging system and laser scanning system. In certain embodiments, the laser scanning system emits multiple electromagnetic wavelengths simultaneously it cause multiple fluorescent labels having different excitation wavelength maximums to fluoresce. The system can simultaneously capture real-time fluorescence images from at least seven cell specimens in the parallel plate flow chamber.

  16. Plant fluid proteomics: Delving into the xylem sap, phloem sap and apoplastic fluid proteomes.

    Science.gov (United States)

    Rodríguez-Celma, Jorge; Ceballos-Laita, Laura; Grusak, Michael A; Abadía, Javier; López-Millán, Ana-Flor

    2016-08-01

    The phloem sap, xylem sap and apoplastic fluid play key roles in long and short distance transport of signals and nutrients, and act as a barrier against local and systemic pathogen infection. Among other components, these plant fluids contain proteins which are likely to be important players in their functionalities. However, detailed information about their proteomes is only starting to arise due to the difficulties inherent to the collection methods. This review compiles the proteomic information available to date in these three plant fluids, and compares the proteomes obtained in different plant species in order to shed light into conserved functions in each plant fluid. Inter-species comparisons indicate that all these fluids contain the protein machinery for self-maintenance and defense, including proteins related to cell wall metabolism, pathogen defense, proteolysis, and redox response. These analyses also revealed that proteins may play more relevant roles in signaling in the phloem sap and apoplastic fluid than in the xylem sap. A comparison of the proteomes of the three fluids indicates that although functional categories are somewhat similar, proteins involved are likely to be fluid-specific, except for a small group of proteins present in the three fluids, which may have a universal role, especially in cell wall maintenance and defense. This article is part of a Special Issue entitled: Plant Proteomics--a bridge between fundamental processes and crop production, edited by Dr. Hans-Peter Mock. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Boundary element method for internal axisymmetric flow

    Directory of Open Access Journals (Sweden)

    Gokhman Alexander

    1999-01-01

    Full Text Available We present an accurate fast method for the computation of potential internal axisymmetric flow based on the boundary element technique. We prove that the computed velocity field asymptotically satisfies reasonable boundary conditions at infinity for various types of inlet/exit. Computation of internal axisymmetric potential flow is an essential ingredient in the three-dimensional problem of computation of velocity fields in turbomachines. We include the results of a practical application of the method to the computation of flow in turbomachines of Kaplan and Francis types.

  18. Antidiarrhoeal Activity of Musa paradisiaca Sap in Wistar Rats

    Directory of Open Access Journals (Sweden)

    Musa T. Yakubu

    2015-01-01

    Full Text Available The folkloric claim of Musa paradisiaca sap in the management of diarrhoea is yet to be substantiated or refuted with scientific data. Therefore, the aim of the current study was to screen the sap of M. paradisiaca for both its secondary metabolites and antidiarrhoeal activity at 0.25, 0.50, and 1.00 mL in rats. Secondary metabolites were screened using standard methods while the antidiarrhoeal activity was done by adopting the castor oil-induced diarrhoeal, castor oil-induced enteropooling, and gastrointestinal motility models. The sap contained flavonoids, phenolics, saponins, alkaloids, tannins, and steroids while cardiac glycosides, anthraquinones, triterpenes, cardenolides, and dienolides were not detected. In the castor oil-induced diarrhoeal model, the sap significantly (P<0.05 prolonged the onset time of diarrhoea, decreased the number, fresh weight, and water content of feaces, and increased the inhibition of defecations. Na+-K+-ATPase activity in the small intestine increased significantly whereas nitric oxide content decreased. The decreases in the masses and volumes of intestinal fluid by the sap were accompanied by increase in inhibition of intestinal fluid content in the enteropooling model. The sap decreased the charcoal meal transit in the gastrointestinal motility model. In all the models, the 1.00 mL of the sap produced changes that compared well with the reference drugs. Overall, the antidiarrhoeal activity of Musa paradisiaca sap attributed to the presence of alkaloids, phenolics, flavonoids, and/or saponins which may involve, among others, enhancing fluid and electrolyte absorption through de novo synthesis of the sodium potassium ATPase and/or reduced nitric oxide levels.

  19. Physico-chemical properties and amino acid profiles of sap from Tunisian date palm

    Directory of Open Access Journals (Sweden)

    Ines Makhlouf-Gafsi

    2016-02-01

    Full Text Available ABSTRACT Date palm sap (Phoenix dactylifera L., also known as “legmi”, is a fresh juice extracted from date palm trees. The present study aimed to elucidate the effects of collection time (at the beginning of the tapping period and after seven days of collection on the amino acid profile and physico-chemical properties of date palm sap from both male and female trees. Dry matter, protein, amino acid, and sugar profiles were determined using the Kjeldahl method, High-Performance Liquid Chromatography (HPLC, and High-Performance Anion-Exchange Chromatography with Pulsed Amperometric Detection (HPAEC-PAD, respectively. Date palm sap from both male and female trees contained high levels of carbohydrates. HPLC analysis showed that this fraction was dominated by sucrose in the sap sample from female trees compared to that from male trees. Male date palm sap was noted to exhibit lower dry matter content than female date palm sap but higher protein, total polyphenol, ash, and amino acid contents. While the major essential amino acids in the sap from male trees consisted of valine and threonine, they were represented by lysine and phenylalanine in sap samples from female trees. Further, Sodium Dodecyl Sulfate Polyacrylamide Gel Electrophoresis (SDS-PAGE analysis showed the presence of a proteinic band of 30 kDa only for the sap from male trees. Taken together, the sap from both male and female date palm trees had a number of properties that are highly valued by the functional food industry.

  20. Measuring sap flow, and other plant physiological conditions across a soil salinity gradient in the lower Colorado River at Cibola National Wildlife Refuge: Vegetation and soil physiology linkages with microwave dielectric constant

    Science.gov (United States)

    McDonald, K. C.; Lasne, Y.; Schroeder, R.; Morino, K.; Hultine, K. R.; Nagler, P. L.

    2009-12-01

    We used ground measurements to examine stand structure and evapotranspiration of Tamarix in the Cibola National Wildlife Refuge (CNWR) on the Lower Colorado River. Three Tamarix study sites were established at different distances from the Colorado River on a river terrace in the CNWR. The sites were chosen from aerial photographs to represent typical dense stands of Tamarix within the CNWR. The sites were representative of differing saline environments, with each having ground water with distinct salt concentration levels. Wells were established at the site to establish depth to water and the salinity concentration within the ground water. We monitored xylem sap flow within each of the three stands. In addition we measured leaf area index to characterize canopy structure. We compared ET, foliage density, depth to water, and salinity among the Tamarix sites to examine stand-level variability driven by the variations in salinity. We supplemented these collections with measurements to characterize soil and vegetation microwave dielectric properties and their relationship to physiologic parameters. The dielectric properties of a material describe the interaction of an electric field with the material. Previous field experiments have demonstrated that varying degrees of correlation exist between vegetation dielectric properties and tree canopy water status. Temporal variation of the dielectric constant of woody plant tissue may result from changes in water status (e.g., water content) and chemical composition, albeit to varying degrees of sensitivity. The varying amount of ground water salinity at CNWR offers a unique opportunity to examine the relationship between vegetation and soil dielectric constant as related to vegetation ecophysiology. A field portable vector network analyzer is used to measure the microwave dielectric spectrum of the soil and vegetation Combined with measurements of vegetation xylem sap flux and soil chemistry, these measurements allow

  1. OpenGGCM-RCM modeling of SAPS events

    Science.gov (United States)

    Raeder, J.; Cramer, W. D.; Jensen, J. B.; Toffoletto, F. R.; Sazykin, S. Y.; Vo, H. B.

    2015-12-01

    Sub-Auroral Polarization Streams (SAPS), also known as Sub-Auroral Ion Drifts (SAIDs), are fast westward flows in the ionosphere that occur at latitudes lower than auroral precipitation, and well separated from the high-latitude convection pattern. Although SAPS were first observed in the ionosphere, they can also be seen in the magnetosphere and are believed to be driven by a combination of region-2 currents and low ionospheric conductance. SAPS are thus governed both by magnetosphere and ionosphere processes and require self-consistently coupled models of the outer magnetosphere, the inner magnetosphere and the ring current, and the ionosphere-thermosphere system. Here, we present first results from the OpenGGCM-RCM coupled model, which includes all of the required physical processes and feedbacks. In particular, the ionospheric conductance is computed self-consistently from both magnetosphere electron precipitation, solar ionization, and ionospheric chemistry within the fully dynamical CTIM sub model of OpenGGCM. Furthermore, CTIM includes the recombination feedback of streaming ions. We focus on the GEM-CEDAR storm events of 2013-03-17, 2011-04-27, 2012-05-07, and 2012-09-02. We show that the coupled model produces SAPS that compare well with data in terms of location, extent, and magnitude. By modifying the conductances in the code we evaluate the potential positive feedback process of the ionospheric conductance on SAPS.

  2. Arsenic speciation in xylem sap of cucumber (Cucumis sativus L.)

    Energy Technology Data Exchange (ETDEWEB)

    Mihucz, Victor G. [Joint Research Group of Environmental Chemistry of the Hungarian Academy of Sciences and L. Eoetvoes University, Budapest (Hungary); Hungarian Satellite Centre of Trace Elements Institute to UNESCO, Budapest (Hungary); Tatar, Eniko [Hungarian Satellite Centre of Trace Elements Institute to UNESCO, Budapest (Hungary); L. Eoetvoes University, Department of Inorganic and Analytical Chemistry, Budapest (Hungary); Virag, Istvan [L. Eoetvoes University, Department of Inorganic and Analytical Chemistry, Budapest (Hungary); Cseh, Edit; Fodor, Ferenc [L. Eoetvoes University, Department of Plant Physiology, Budapest (Hungary); Zaray, Gyula [Joint Research Group of Environmental Chemistry of the Hungarian Academy of Sciences and L. Eoetvoes University, Budapest (Hungary); Hungarian Satellite Centre of Trace Elements Institute to UNESCO, Budapest (Hungary); L. Eoetvoes University, Department of Inorganic and Analytical Chemistry, Budapest (Hungary)

    2005-10-01

    Flow injection analysis (FIA) and high-performance liquid chromatography double-focusing sector field inductively coupled plasma mass spectrometry (HPLC-DF-ICP-MS) were used for total arsenic determination and arsenic speciation of xylem sap of cucumber plants (Cucumis sativus L.) grown in hydroponics containing 2 {mu}mol dm{sup -3} arsenate or arsenite, respectively. Arsenite [As(III)], arsenate [As(V)] and dimethylarsinic acid (DMA) were identified in the sap of the plants. Arsenite was the predominant arsenic species in the xylem saps regardless of the type of arsenic treatment, and the following concentration order was determined: As(III) > As(V) > DMA. The amount of total As, calculated taking into consideration the mass of xylem sap collected, was almost equal for both treatments. Arsenite was taken up more easily by cucumber than arsenate. Partial oxidation of arsenite to arsenate (<10% in 48 h) was observed in the case of arsenite-containing nutrient solutions, which may explain the detection of arsenate in the saps of plants treated with arsenite. (orig.)

  3. Fluxo de seiva xilemática em mamoeiro 'Golden' cultivado por microaspersão sobre copa: relações com as variáveis ambientais Relationship between sap flow and environmental variables in a microspray irrigation upon papaya tree canopy

    Directory of Open Access Journals (Sweden)

    Fabrício de Oliveira Reis

    2009-01-01

    generally caused by the deficit of water in the soil, in the atmosphere or in both. The environmental variables control the plant water loss. However, high values of leaf to air vapor pressure deficit (VPDleaf-to-air can cause the stomatal closure and can reduce the transpiration process, mainly in large trees. In this experiment, it was used the heat dissipation method developed by GRANIER (1985 to sap flow measurements. The aim of this study was to determine the relationship between xylem sap flow and reference evapotranspiration (ET0 in papaya plants cultivated with and without microspray irrigation over canopy and under field conditions. It was also investigated the relationship between xylem sap flow, photosynthetic photons flux density (PPFD and air vapor pressure deficit (VPDair values. There was a delay between the loss of water through the leaves and the movement of water through the trunk (lag phase. From January to March, there was a better relation between xylem sap flow and VPDair, which was not observed from June to August, probably because of this lag phase. From January to March, plants cultivated with microaspersion showed an increase in xylem sap flow, in relation to plants cultivated without microaspersion when, at this stage, the ET0 was higher.

  4. Sap Flux Scaled Transpiration in Ring-porous Tree Species: Assumptions, Pitfalls and Calibration

    Science.gov (United States)

    Bush, S. E.; Hultine, K. R.; Ehleringer, J. R.

    2008-12-01

    Thermal dissipation probes for measuring sap flow (Granier-type) at the whole tree and stand level are routinely used in forest ecology and site water balance studies. While the original empirical relationship used to calculate sap flow was reported as independent of wood anatomy (ring-porous, diffuse-porous, tracheid), it has been suggested that potentially large errors in sap flow calculations may occur when using the original calibration for ring-porous species, due to large radial trends in sap velocity and/or shallow sapwood depth. Despite these concerns, sap flux measurements have rarely been calibrated in ring-porous taxa. We used a simple technique to calibrate thermal dissipation sap flux measurements on ring-porous trees in the lab. Calibration measurements were conducted on five ring-porous species in the Salt Lake City, USA metropolitan area including Quercus gambelii (Gambel oak), Gleditsia triacanthos (Honey locust), Elaeagnus angustifolia (Russian olive), Sophora japonica (Japanese pagoda), and Celtis occidentalis (Common hackberry). Six stems per species of approximately 1 m in length were instrumented with heat dissipation probes to measure sap flux concurrently with gravimetric measurements of water flow through each stem. Safranin dye was pulled through the stems following flow rate measurements to determine sapwood area. As expected, nearly all the conducting sapwood area was limited to regions within the current year growth rings. Consequently, we found that the original Granier equation underestimated sap flux density for all species considered. Our results indicate that the use of thermal dissipation probes for measuring sap flow in ring-porous species should be independently calibrated, particularly when species- specific calibration data are not available. Ring-porous taxa are widely distributed and represent an important component of the regional water budgets of many temperate regions. Our results are important for evaluating plant water

  5. Auditing and GRC automation in SAP

    CERN Document Server

    Chuprunov, Maxim

    2013-01-01

    Going beyond current literature, this book extends internal controls to efficiency and profitability. Offers an audit guide for an SAP ERP system, covers risks and control descriptions, and shows how to automate compliance management based on SAP GRC.

  6. Tree Hydraulics: How Sap Rises

    Science.gov (United States)

    Denny, Mark

    2012-01-01

    Trees transport water from roots to crown--a height that can exceed 100 m. The physics of tree hydraulics can be conveyed with simple fluid dynamics based upon the Hagen-Poiseuille equation and Murray's law. Here the conduit structure is modelled as conical pipes and as branching pipes. The force required to lift sap is generated mostly by…

  7. Tree Hydraulics: How Sap Rises

    Science.gov (United States)

    Denny, Mark

    2012-01-01

    Trees transport water from roots to crown--a height that can exceed 100 m. The physics of tree hydraulics can be conveyed with simple fluid dynamics based upon the Hagen-Poiseuille equation and Murray's law. Here the conduit structure is modelled as conical pipes and as branching pipes. The force required to lift sap is generated mostly by…

  8. Inner strategies of coping with operational work amongst SAPS officers

    Directory of Open Access Journals (Sweden)

    Masefako A. Gumani

    2013-03-01

    Full Text Available Orientation: Identification of the inner coping strategies used by South African Police Service (SAPS officers who do operational work is something the SAPS should consider to ensure the officers’ management of trauma and efficiency at work.Research purpose: The objective of this study was to describe inner coping strategies used by officers in the Vhembe district (South Africa to reconstruct stressful and traumatic experiences at work.Motivation for the study: Most studies on coping amongst SAPS officers focus on organisational stress and not on the impact of the officers’ operational work.Research design, approach and method: An exploratory design was used and 20 SAPS officers were selected through purposive sampling. In-depth face-to-face and telephone interviews, as well as diaries were used to collect data, which were analysed using content thematic data analysis.Main findings: The results showed that the main categories of coping strategies that led to management of the impact of operational work amongst the selected sample were centred around problem-focused and emotion-focused strategies, with some use of reappraisal and minimal use of avoidance. Considering the context of the officers’ work, the list of dimensions of inner coping strategies amongst SAPS officers should be extended.Practical/managerial implications: Intervention programmes designed for the SAPS, including critical incident stress debriefing, should take the operational officers’ inner strategies into account to improve the management of the impact of their work.Contribution/value-add: This study contributes to the body of knowledge on the inner coping strategies amongst SAPS officers, with special reference to operational work in a specific setting.

  9. Dynamic control of osmolality and ionic composition of the xylem sap in two mangrove species.

    Science.gov (United States)

    López-Portillo, Jorge; Ewers, Frank W; Méndez-Alonzo, Rodrigo; Paredes López, Claudia L; Angeles, Guillermo; Alarcón Jiménez, Ana Luisa; Lara-Domínguez, Ana Laura; Torres Barrera, María Del Carmen

    2014-06-01

    • Premise of the study: Xylem sap osmolality and salinity is a critical unresolved issue in plant function with impacts on transport efficiency, pressure gradients, and living cell turgor pressure, especially for halophytes such as mangrove trees.• Methods: We collected successive xylem vessel sap samples from stems and shoots of Avicennia germinans and Laguncularia racemosa using vacuum and pressure extraction and measured their osmolality. Following a series of extractions with the pressure chamber, we depressurized the shoot and pressurized again after various equilibration periods (minutes to hours) to test for dynamic control of osmolality. Transpiration and final sap osmolality were measured in shoots perfused with deionized water or different seawater dilutions.• Key results: For both species, the sap osmolality values of consecutive samples collected by vacuum extraction were stable and matched those of the initial samples extracted with the pressure chamber. Further extraction of samples with the pressure chamber decreased sap osmolality, suggesting reverse osmosis occurred. However, sap osmolalities increased when longer equilibration periods after sap extraction were allowed. Analysis of expressed sap with HPLC indicated a 1:1 relation between measured osmolality and the osmolality of the inorganic ions in the sap (mainly Na(+), K(+), and Cl(-)), suggesting no contamination by organic compounds. In stems perfused with deionized water, the sap osmolality increased to mimic the native sap osmolality.• Conclusions: Xylem sap osmolality and ionic contents are dynamically adjusted by mangroves and may help modulate turgor pressure, hydraulic conductivity, and water potential, thus being important for mangrove physiology, survival, and distribution. © 2014 Botanical Society of America, Inc.

  10. Advanced overset methods for vortex dominated flows

    Science.gov (United States)

    Foster, Norman F.

    A newly implemented computational method of high-order accuracy is presented for the accurate calculation of unsteady vortical structures that may produce aeroacoustic sources, or affect downstream structural responses. The method involves prediction of the mean flow field by solving the Navier-Stokes equations (NSE) using a computational fluid dynamics (CFD) solver that employs high-order discretization on overlapping (overset) grid systems. The method dramatically reduces the artificial dissipation and dispersion of vortical flow features that would ordinarily be lost or degraded with the use of current methods. Complex domains are discretized using an overset grid strategy that allows for the use of multiple high quality structured meshes. The high-order method is developed and incorporated into a generalized overset grid assembly scheme, which allows high-order spatial accuracy of the NSE solutions to be maintained across overset grid boundaries. Comparisons are made to calculations that do not preserve high-order accuracy at overset boundaries, and insight is obtained into the effects and sensitivities of different treatments of overlapping boundaries. A nested block adaptive mesh refinement (AMR) method has also been developed, within the context of the overset paradigm. The method is shown to significantly improve accuracy for a given computational cell count by tracking dynamic vortical features using appropriate dynamic refinement and coarsening, and its implementation in the context of the high-order overset method is presented. The computational procedures presented herein are tested against analytic and canonical cases (slightly compressible, M ≤ 0.5, and incompressible mean flows) in order to characterize the accuracy of flow field calculations using high-order discretization and overset schemes across overlapping grid boundaries. The methods are also extended to far more complex systems including the transport of rotorcraft hub vorticity to

  11. Influence of stem temperature changes on heat pulse sap flux density measurements.

    Science.gov (United States)

    Vandegehuchte, Maurits W; Burgess, Stephen S O; Downey, Alec; Steppe, Kathy

    2015-04-01

    While natural spatial temperature gradients between measurement needles have been thoroughly investigated for continuous heat-based sap flow methods, little attention has been given to how natural changes in stem temperature impact heat pulse-based methods through temporal rather than spatial effects. By modelling the theoretical equation for both an ideal instantaneous pulse and a step pulse and applying a finite element model which included actual needle dimensions and wound effects, the influence of a varying stem temperature on heat pulse-based methods was investigated. It was shown that the heat ratio (HR) method was influenced, while for the compensation heat pulse and Tmax methods changes in stem temperatures of up to 0.002 °C s(-1) did not lead to significantly different results. For the HR method, rising stem temperatures during measurements led to lower heat pulse velocity values, while decreasing stem temperatures led to both higher and lower heat pulse velocities, and to imaginary results for high flows. These errors of up to 40% can easily be prevented by including a temperature correction in the data analysis procedure, calculating the slope of the natural temperature change based on the measured temperatures before application of the heat pulse. Results of a greenhouse and outdoor experiment on Pinus pinea L. show the influence of this correction on low and average sap flux densities.

  12. Finite element methods for incompressible flow problems

    CERN Document Server

    John, Volker

    2016-01-01

    This book explores finite element methods for incompressible flow problems: Stokes equations, stationary Navier-Stokes equations, and time-dependent Navier-Stokes equations. It focuses on numerical analysis, but also discusses the practical use of these methods and includes numerical illustrations. It also provides a comprehensive overview of analytical results for turbulence models. The proofs are presented step by step, allowing readers to more easily understand the analytical techniques.

  13. Effects of Partial Rootzone Drying on Sap Flow and Water Balance of Pear Trees Under a Shallow Ground Water Table Condition%地下水位较高条件下不同根区湿润方式对 梨树根与茎液流及其水分平衡的影响

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The experiments were conducted to test sap flow and water balance of pear trees response to partial rootzone drying under a shallow water table condition. Three treatments, i.e. conventional flood irrigation (CFI), fixed 1/2 partial rootzone drying and the other 1/2 part irrigated (PRD), and alternate 1/2 partial rootzone drying and irrigating (ARDI), were designed. The EnviroSCAN probes and heat pulse sensors were used to monitor soil water dynamics and sap flow respectively. The results shown that the root sap flow of wet side was much larger than that of dry side in PRD and ARDI, also larger than that of the same side in CFI. The root sap flow of dry side in ARDI was restored and improved more quickly than in PRD after rewetting. The trunk sap flow in PRD was smaller than in CFI when one side was drying, and it was larger than in CFI after the dry side rewetting. The trunk sap flow in ARDI was smaller than in CFI, but larger than in PRD during one side drying. The daily water consumption in ARDI and PRD was smaller than that in CFI during the period of only one side irrigated. The compensatory effect for water uptake existed in the roots of wet side for ARDI and PRD, and the ability of root water uptake was enhanced when the dry side rewetting, and it related the duration of root drying. Daily root sap flow was significantly related to reference evapotranspiration, but these relations were markedly different for different surface wetting patterns and different sides. The daily trunk sap flow was also related to reference evapotranspiration, and the ratio of trunk sap flow and reference evapotranspiration was not same for the same soil water content under different surface wetting patterns. Irrigation water use was approximately reduced 1/2 in ARDI and in the drying periods of PRD compared with CFI, but water consumption of trees and trunk sap flow were not reduced the same percentage. The effects of partial rootzone drying on water balance and sap flow were

  14. Transformation of Commercial Flows into Physical Flows of Electricity – Flow Based Method

    Directory of Open Access Journals (Sweden)

    M. Adamec

    2009-01-01

    Full Text Available We are witnesses of large – scale electricity transport between European countries under the umbrella of the UCTE organization. This is due to the inabilyof generators to satisfy the growing consumption in some regions. In this content, we distinguish between two types of flow. The first type is physical flow, which causes costs in the transmission grid, whilst the second type is commercial flow, which provides revenues for the market participants. The old methods for allocating transfer capacity fail to take this duality into account. The old methods that allocate transmission border capacity to “virtual” commercial flows which, in fact, will not flow over this border, do not lead to optimal allocation. Some flows are uselessly rejected and conversely, some accepted flows can cause congestion on another border. The Flow Based Allocation method (FBA is a method which aims to solve this problem.Another goal of FBA is to ensure sustainable development of expansion of transmission capacity. Transmission capacity is important, because it represents a way to establish better transmission system stability, and it provides a distribution channel for electricity to customers abroad. For optimal development, it is necessary to ensure the right division of revenue allocation among the market participants.This paper contains a brief description of the FBA method. Problems of revenue maximization and optimal revenue distribution are mentioned. 

  15. Diurnal and seasonal variability in radial distribution of sap flux density: Implications for estimating stand transpiration.

    Science.gov (United States)

    Fiora, Alessandro; Cescatti, Alessandro

    2006-09-01

    Daily and seasonal patterns in radial distribution of sap flux density were monitored in six trees differing in social position in a mixed coniferous stand dominated by silver fir (Abies alba Miller) and Norway spruce (Picea abies (L.) Karst) in the Alps of northeastern Italy. Radial distribution of sap flux was measured with arrays of 1-cm-long Granier probes. The radial profiles were either Gaussian or decreased monotonically toward the tree center, and seemed to be related to social position and crown distribution of the trees. The ratio between sap flux estimated with the most external sensor and the mean flux, weighted with the corresponding annulus areas, was used as a correction factor (CF) to express diurnal and seasonal radial variation in sap flow. During sunny days, the diurnal radial profile of sap flux changed with time and accumulated photosynthetic active radiation (PAR), with an increasing contribution of sap flux in the inner sapwood during the day. Seasonally, the contribution of sap flux in the inner xylem increased with daily cumulative PAR and the variation of CF was proportional to the tree diameter, ranging from 29% for suppressed trees up to 300% for dominant trees. Two models were developed, relating CF with PAR and tree diameter at breast height (DBH), to correct daily and seasonal estimates of whole-tree and stand sap flow obtained by assuming uniform sap flux density over the sapwood. If the variability in the radial profile of sap flux density was not accounted for, total stand transpiration would be overestimated by 32% during sunny days and 40% for the entire season.

  16. A phloem-sap feeder mixes phloem and xylem sap to regulate osmotic potential.

    Science.gov (United States)

    Pompon, Julien; Quiring, Dan; Goyer, Claudia; Giordanengo, Philippe; Pelletier, Yvan

    2011-09-01

    Phloem-sap feeders (Hemiptera) occasionally consume the dilute sap of xylem, a behaviour that has previously been associated with replenishing water balance following dehydration. However, a recent study reported that non-dehydrated aphids ingested xylem sap. Here, we tested the hypothesis that the consumption of xylem sap, which has a low osmolality, is a general response to osmotic stresses other than dehydration. Alate aphids were subjected to different treatments and subsequently transferred onto a plant, where electrical penetration graph (EPG) was used to estimate durations of passive phloem sap consumption and active sucking of xylem sap. The proportion of time aphids fed on xylem sap (i.e., time spent feeding on xylem sap/total time spent feeding on phloem plus xylem sap) was used as a proxy of the solute concentration of the uptake. The proportion of time alate aphids fed on xylem sap increased: (1) with the time spent imbibing an artificial diet containing a solution of sucrose, which is highly concentrated in phloem sap and is mainly responsible for the high osmotic potential of phloem sap; (2) with the osmotic potential of the artificial diet, when osmotic potential excess was not related to sucrose concentration; and (3) when aphids were deprived of primary symbionts, a condition previously shown to lead to a higher haemolymph osmotic potential. All our results converge to support the hypothesis that xylem sap consumption contributes to the regulation of the osmotic potential in phloem-sap feeders.

  17. Numerical Methods For Chemically Reacting Flows

    Science.gov (United States)

    Leveque, R. J.; Yee, H. C.

    1990-01-01

    Issues related to numerical stability, accuracy, and resolution discussed. Technical memorandum presents issues in numerical solution of hyperbolic conservation laws containing "stiff" (relatively large and rapidly changing) source terms. Such equations often used to represent chemically reacting flows. Usually solved by finite-difference numerical methods. Source terms generally necessitate use of small time and/or space steps to obtain sufficient resolution, especially at discontinuities, where incorrect mathematical modeling results in unphysical solutions.

  18. Projecte d'integració entre SAP GH - SAP MM - Kàrdex

    OpenAIRE

    Perea Núñez, Yolanda

    2012-01-01

    Projecte d'integració entre dos sistemes SAP (gestió hospitalària i gestió de materials) amb un altre sistema aliè a SAP, el sistema de magatzem de medicaments Kàrdex, mitjançant comunicacions via SAP Process Integration. Proyecto de integración entre dos sistemas SAP (gestión hospitalaria y gestión de materiales) con otro sistema ajeno a SAP, el sistema de almacén de medicamentos Kardex, mediante comunicaciones vía SAP Process Integration.

  19. Projecte d'integració entre SAP GH - SAP MM - Kàrdex

    OpenAIRE

    Perea Núñez, Yolanda

    2012-01-01

    Projecte d'integració entre dos sistemes SAP (gestió hospitalària i gestió de materials) amb un altre sistema aliè a SAP, el sistema de magatzem de medicaments Kàrdex, mitjançant comunicacions via SAP Process Integration. Proyecto de integración entre dos sistemas SAP (gestión hospitalaria y gestión de materiales) con otro sistema ajeno a SAP, el sistema de almacén de medicamentos Kardex, mediante comunicaciones vía SAP Process Integration.

  20. Evaluasi Implementasi SAP Modul Material Management: Studi Kasus pada PT Bumitama Gunajaya Agro

    Directory of Open Access Journals (Sweden)

    Santo Fernandi Wijaya

    2012-06-01

    Full Text Available An integrated information system is a necessity for a company to help solve problems in business transactions management. SAP application is an application that is able to provide solutions to such problems. The purpose of this study was to evaluate the running business processes on the Material Management module;evaluate the performance of the running SAP systems associated with the implementation and maintenance of SAP applications as well as to give sugestions based on the development of evaluation results obtained, in terms of business processes, performance, and financial. Utilized for analysis is IT Balanced Scorecard method, while ASAP (Accelerated SAP method is used for the system development. This study produced an analysis of the evaluation of the enterprise business processes in implementing the SAP development of ERP system modulesMaterial Management.

  1. Performance of stem flow gauges in greenhouse and desert environments

    Energy Technology Data Exchange (ETDEWEB)

    Levitt, D.G. [Reynolds Electrical and Engineering Co., Inc., Las Vegas, NV (United States); Simpson, J.R. [California Univ., Davis, CA (United States). Dept. of Environmental Horticulture; Tipton, J.L. [Arizona Univ., Tucson, AZ (United States). Dept. of Plant Sciences

    1995-06-01

    This study was conducted to evaluate the accuracy and general performance of a heat balance method for estimating transpirational sap flow through plant stems on two tree species in greenhouse and field experiments in Tucson, Arizona. Sap flow through 20-mm diameter stems of oak (Quercus virginiana `Heritage`) and mesquite (Prosopis alba `Colorado`.) trees in containers was measured using stem flow gauges and a precision balance, from January to October, 1991. Overall gauge accuracy, and the effects of gauge location on the tree stem, gauge ventilation, gauge insulation, sheath conductance factor (Ksh) selection method, and increased numbers of vertical thermocouple pairs on gauge performance were evaluated.

  2. Flow cytometric detection method for DNA samples

    Energy Technology Data Exchange (ETDEWEB)

    Nasarabadi,Shanavaz (Livermore, CA); Langlois, Richard G. (Livermore, CA); Venkateswaran, Kodumudi S. (Round Rock, TX)

    2011-07-05

    Disclosed herein are two methods for rapid multiplex analysis to determine the presence and identity of target DNA sequences within a DNA sample. Both methods use reporting DNA sequences, e.g., modified conventional Taqman.RTM. probes, to combine multiplex PCR amplification with microsphere-based hybridization using flow cytometry means of detection. Real-time PCR detection can also be incorporated. The first method uses a cyanine dye, such as, Cy3.TM., as the reporter linked to the 5' end of a reporting DNA sequence. The second method positions a reporter dye, e.g., FAM.TM. on the 3' end of the reporting DNA sequence and a quencher dye, e.g., TAMRA.TM., on the 5' end.

  3. Disruption of each of the secreted aspartyl proteinase genes SAP1, SAP2, and SAP3 of Candida albicans attenuates virulence.

    OpenAIRE

    Hube, B.; Sanglard, D.; Odds, F C; Hess, D; Monod, M.; Schäfer, W.; Brown, A. J.; Gow, N A

    1997-01-01

    Secreted aspartyl proteinases (Saps), encoded by a gene family with at least nine members (SAP1 to SAP9), are one of the most discussed virulence factors produced by the human pathogen Candida albicans. In order to study the role of each Sap isoenzyme in pathogenicity, we have constructed strains which harbor mutations at selected SAP genes. SAP1, SAP2, and SAP3, which are regulated differentially in vitro, were mutated by targeted gene disruption. The growth rates of all homozygous null muta...

  4. Disruption of each of the secreted aspartyl proteinase genes SAP1, SAP2, and SAP3 of Candida albicans attenuates virulence.

    OpenAIRE

    Hube, B.; Sanglard, D; Odds, F C; Hess, D; Monod, M; Schäfer, W.; Brown, A J; Gow, N A

    1997-01-01

    Secreted aspartyl proteinases (Saps), encoded by a gene family with at least nine members (SAP1 to SAP9), are one of the most discussed virulence factors produced by the human pathogen Candida albicans. In order to study the role of each Sap isoenzyme in pathogenicity, we have constructed strains which harbor mutations at selected SAP genes. SAP1, SAP2, and SAP3, which are regulated differentially in vitro, were mutated by targeted gene disruption. The growth rates of all homozygous null muta...

  5. Potential of Jatropha multifida sap against traumatic ulcer

    Directory of Open Access Journals (Sweden)

    Basri A. Gani

    2015-09-01

    Full Text Available Background: Traumatic ulcer is a lesion in oral mucosa as a result of physical and mechanical trauma, as well as changes in salivary pH. Jatropha multifida sap can act as antimicrobial, anti-inflammatory and re-epithelialization, and can also trigger the healing process of ulcers. Purpose: Research was aimed to determine the potential of Jatropha multifida sap against traumatic ulcer base on clinical and histopathological healing process. Method: This research was conducted laboratory experimental model, with rats (Rattus norvegicus as the subject as well as Jatropha multifida sap for ulcer healing. Those subjects were divided into four groups: two treatment groups administrated with pellet and Jatropha multifida sap, one group as the positive control group administrated with 0.1% triamcinolone acetonide, and one group as the negative control group administrated with 0.9% NaCl. Ulcer manipulation was used 30% H2O2, and evaluation of ulcer healing was used clinical and histopathological approach. Result: Clinically, the healing process of ulcers in the treatment group with Jatropha multifida sap was faster than that in the positive control group with 0.1% triamcinolone acetonide, indicated with the reduction of the ulcer size until the missing of the ulcers started from the third day to the seventh one (p≤0.05. Histopathologically inflammatory cells (lymphocytes, and plasma cells declined started from the third day, and the formation of collagen and re-epithelialization then occurred. On the seventh day, the epithelial cells thickened, and the inflammatory cells infiltrated. Statistically, those groups were significant (p≤0.05. Conclusion: Jatropha multifida sap has a significant potential to cure traumatic ulcers on oral mucosa clinically and histopathologically.

  6. Integrating Adobe Interactive Forms in SAP Netweaver

    OpenAIRE

    Atagana, Rex Ogheneakpobo

    2013-01-01

    Systems, Applications and Products in Data Processing (SAP), the leader in Enterprise Resource Planning Software (ERP) as a strategy is moving its technology into Virtualization. In light of that, this project utilized SAP Netweaver VMware edition which is licensed for developers to illustrate the integration of Adobe interactive forms. SAP as a practice has installation notes for every solution, but they are not uniformly released. Thus technical consultants encounters compatibility chal...

  7. Sap flow and sugar transport in plants

    OpenAIRE

    Jensen, Kaare Hartvig; Berg-Sørensen, Kirstine; Bruus, Henrik; Holbrook, N. M.; Liesche, J.; Schulz, A.; Zwieniecki, M. A.; Bohr, Tomas

    2016-01-01

    Green plants are Earth’s primary solar energy collectors. They harvest the energy of the Sun by converting light energy into chemical energy stored in the bonds of sugar molecules. A multitude of carefully orchestrated transport processes are needed to move water and minerals from the soil to sites of photosynthesis and to distribute energy-rich sugars throughout the plant body to support metabolism and growth. The long-distance transport happens in the plants’ vascular system, where water an...

  8. Sap flow and sugar transport in plants

    DEFF Research Database (Denmark)

    Jensen, K. H.; Berg-Sørensen, K.; Bruus, H.;

    2016-01-01

    Green plants are Earth's primary solar energy collectors. They harvest the energy of the sun by converting light energy into chemical energy stored in the bonds of sugar molecules. A multitude of carefully orchestrated transport processes are needed to move water and minerals from the soil to sites...... of photosynthesis, and to distribute energy-rich sugars throughout the plant body to support metabolism and growth. The long-distance transport happens in the plants' vascular system, where water and solutes are moved along the entire length of the plant. In this review, we discuss the current understanding...... are given on some of the open questions of this research field....

  9. New nodal methods for fluid flow equations

    Science.gov (United States)

    Michael, Edward-Pierre Edward

    Several new highly accurate and highly efficient computational methods, called nodal integral methods (NIMs), for solving steady-state and time-dependent fluid flow equations have been developed. First, a new third order nodal integral method for solving the linear, two-dimensional, steady-state, convection-diffusion equation was developed without introducing Legendre moments of the dependent variable higher than the zeroth moment. Numerical comparisons of the new method with the second order NIM, the upwind difference scheme (UWDS) and the locally exact consistent upwind scheme of second order (LECUSSO) showed that, in the important 1% error range, the new method is more efficient than the UWDS, and the LECUSSO scheme, but, less efficient than the second order NIM. Also two new methods for solving the generic, two-dimensional, time-dependent, convection-diffusion equation were developed. One is a full space-time NIM in which both the spatial and temporal operators are discretized using the nodal integral approach. The other is a hybrid finite-difference/NIM method in which the temporal operator is discretized using a backward finite-difference approximation, and the spatial operator is discretized using the nodal integral approach. It was found, as expected, that the full space-time NIM is second order in both space and time while the hybrid finite-difference/NIM is second order in space but only first order in time. Finally, two new methods for solving the conservation of mass and the Navier-Stokes equations for incompressible fluid flow were developed. One is for the steady-state mass and Navier-Stokes equations while the other solves the time-dependent equations. The spatial stencils that result from these new formulations for the mass and the Navier-Stokes equations are similar to those obtained by traditional staggered-grid finite-difference methods. However, the new methods use second order approximations for both the velocities and the pressures. These

  10. Role of Candida albicans-Secreted Aspartyl Proteinases (Saps in Severe Early Childhood Caries

    Directory of Open Access Journals (Sweden)

    Wenqing Li

    2014-06-01

    Full Text Available Candida albicans is strongly associated with severe early childhood caries (S-ECC. However, the roles of secreted aspartyl proteinases (Saps, an important virulence factor of C. albicans, in the progress of S-ECC are not clear. In our study, the Saps activities were evaluated by the yeast nitrogen base–bovine serum albumi (YNB–BSA agar plate method and by the MTT method with bovine serum albumin (BSA as the substrate. Genotypes of C. albicans and gene expression of Sap1–5 were evaluated. The relationships of Saps activities and genotypes with S-ECC were analyzed. The results showed that enzyme activities of Saps in the S-ECC group were significantly higher than those in the caries free (CF group (p < 0.05. Genotypes A, B and C were detected in the S-ECC group, and genotypes A and C were detected in the CF group. In the genotype A group, Saps activity in the S-ECC group was significantly different from that in the CF group (p < 0.05. The gene expression level of Sap1 in the S-ECC group was significantly higher than that in the CF group (p = 0.001, while Sap4 expression was significantly lower than that in the CF group (p = 0.029. It can be concluded that Sap1–5 are the predominant proteinase genes expressed in C. albicans from dental biofilm and Sap1 may play an important role in the development of S-ECC.

  11. CAPILLARY ELECTROPHORETIC ANALYSIS OF LOW-MOLECULAR-MASS OF CA SPECIES IN PHLOEM SAP OF Ricinus communis L.

    Directory of Open Access Journals (Sweden)

    Noor Fitri

    2010-06-01

    Full Text Available A capillary electrophoretic (CE analysis with ultra-violet (UV detection was performed for further separation of low-molecular-mass (LMM calcium species in phloem sap of Ricinus communis L. Two different background electrolytes (BGE were used for the separation; these are (1 hydrogen phosphate/dihydrogen phosphate buffer containing cetyltrimethylammonium bromide (CTAB as an electro-osmotic flow (EOF modifier, and (2 boric acid buffer containing CTAB. Various parameters affecting the analysis, including the composition and pH of the BGE were systematically studied. The sensitivity, resolution, baseline noise, migration time of the species peaks, and reproducibility of the method were evaluated under optimised condition. At least 13 UV-active species were optimally separated within about ten minutes. The optimised measurement condition was also achieved using 10 mM hydrogen phosphate/10 mM dihydrogen phosphate containing 0.5 mM CTAB at pH 8.0 as BGE, and by applying voltage of ‑20 kV and temperature of 14°C. Evidently, the analytical method was successfully used for the separation of LMM calcium species in phloem sap of R. communis L.   Keywords: capillary electrophoresis, calcium species, phloem sap, Ricinus communis

  12. Architecture of SAP ERP understand how successful software works

    CERN Document Server

    Boeder, Jochen

    2014-01-01

    This book - compiled by software architects from SAP - is a must for consultants, developers, IT managers, and students working with SAP ERP, but also users who want to know the world behind their SAP user interface.

  13. A randomized controlled trial of interventions to impede date palm sap contamination by bats to prevent nipah virus transmission in Bangladesh.

    Directory of Open Access Journals (Sweden)

    Salah Uddin Khan

    Full Text Available BACKGROUND: Drinking raw date palm sap is a risk factor for human Nipah virus (NiV infection. Fruit bats, the natural reservoir of NiV, commonly contaminate raw sap with saliva by licking date palm's sap producing surface. We evaluated four types of physical barriers that may prevent bats from contacting sap. METHODS: During 2009, we used a crossover design and randomly selected 20 date palm sap producing trees and observed each tree for 2 nights: one night with a bamboo skirt intervention applied and one night without the intervention. During 2010, we selected 120 trees and randomly assigned four types of interventions to 15 trees each: bamboo, dhoincha (local plant, jute stick and polythene skirts covering the shaved part, sap stream, tap and collection pot. We enrolled the remaining 60 trees as controls. We used motion sensor activated infrared cameras to examine bat contact with sap. RESULTS: During 2009 bats contacted date palm sap in 85% of observation nights when no intervention was used compared with 35% of nights when the intervention was used [p<0.001]. Bats were able to contact the sap when the skirt did not entirely cover the sap producing surface. Therefore, in 2010 we requested the sap harvesters to use larger skirts. During 2010 bats contacted date palm sap [2% vs. 83%, p<0.001] less frequently in trees protected with skirts compared to control trees. No bats contacted sap in trees with bamboo (p<0.001 compared to control, dhoincha skirt (p<0.001 or polythene covering (p<0.001, but bats did contact sap during one night (7% with the jute stick skirt (p<0.001. CONCLUSION: Bamboo, dhoincha, jute stick and polythene skirts covering the sap producing areas of a tree effectively prevented bat-sap contact. Community interventions should promote applying these skirts to prevent occasional Nipah spillovers to human.

  14. 论冶金企业 SAP 系统的二次开发技术%Secondary Development Technology for the SAP System of Metallurgical Enterprises

    Institute of Scientific and Technical Information of China (English)

    司海霞

    2013-01-01

    The concept, functional modules, development language ABAP and develop-ment method of the management software SAP system for enterprises are briefly introduced. The technical method and its essentials for the secondary development of the SAP system are discussed through actual project examples.%  简要介绍企业管理软件 SAP 系统的概念、功能模块、开发语言 ABAP 及开发方法,通过例举项目实施中的实例详细说明了 SAP 系统二次开发的技术方法及要点。

  15. Baseliner: An open-source, interactive tool for processing sap flux data from thermal dissipation probes

    Science.gov (United States)

    Oishi, A. Christopher; Hawthorne, David A.; Oren, Ram

    Estimating transpiration from woody plants using thermal dissipation sap flux sensors requires careful data processing. Currently, researchers accomplish this using spreadsheets, or by personally writing scripts for statistical software programs (e.g., R, SAS). We developed the Baseliner software to help establish a standardized protocol for processing sap flux data. Baseliner enables users to QA/QC data and process data using a combination of automated steps, visualization, and manual editing. Data processing requires establishing a zero-flow reference value, or "baseline", which varies among sensors and with time. Since no set of algorithms currently exists to reliably QA/QC and estimate the zero-flow baseline, Baseliner provides a graphical user interface to allow visual inspection and manipulation of data. Data are first automatically processed using a set of user defined parameters. The user can then view the data for additional, manual QA/QC and baseline identification using mouse and keyboard commands. The open-source software allows for user customization of data processing algorithms as improved methods are developed.

  16. Self-healing mortar with pH-sensitive superabsorbent polymers: testing of the sealing efficiency by water flow tests

    Science.gov (United States)

    Gruyaert, Elke; Debbaut, Brenda; Snoeck, Didier; Díaz, Pilar; Arizo, Alejandro; Tziviloglou, Eirini; Schlangen, Erik; De Belie, Nele

    2016-08-01

    Superabsorbent polymers (SAPs) have potential to be used as healing agent in self-healing concrete due to their property to attract moisture from the environment and their capacity to promote autogenous healing. A possible drawback, however, is their uptake of mixing water during concrete manufacturing, resulting in an increased volume of macro-pores in the hardened concrete. To limit this drawback, newly developed SAPs with a high swelling and pH-sensitiveness were developed and tested within the FP7 project HEALCON. Evaluation of their self-sealing performance occurred through a water permeability test via water flow, a test method also developed within HEALCON. Three different sizes of the newly developed SAP were compared with a commercial SAP. Swelling tests in cement filtrate solution indicated that the commercial and in-house synthesized SAPs performed quite similar, but the difference between the swelling capacity at pH 9 and pH 13 is more pronounced for the self-synthesized SAPs. Moreover, in comparison to the commercial SAPs, less macro-pores are formed in the cement matrix of mixes with self-synthesized SAPs and the effect on the mechanical properties is lower, but not negligible, when using high amounts of SAPs. Although the immediate sealing effect of cracks in mortar was the highest for the commercial SAPs, the in-house made SAPs with a particle size between 400 and 600 μm performed the best with regard to crack closure (mainly CaCO3 precipitation) and self-sealing efficiency, after exposing the specimens to 28 wet-dry cycles. Some specimens could even withstand a water pressure of 2 bar.

  17. Flow “Fine” Synthesis: High Yielding and Selective Organic Synthesis by Flow Methods

    Science.gov (United States)

    2015-01-01

    Abstract The concept of flow “fine” synthesis, that is, high yielding and selective organic synthesis by flow methods, is described. Some examples of flow “fine” synthesis of natural products and APIs are discussed. Flow methods have several advantages over batch methods in terms of environmental compatibility, efficiency, and safety. However, synthesis by flow methods is more difficult than synthesis by batch methods. Indeed, it has been considered that synthesis by flow methods can be applicable for the production of simple gasses but that it is difficult to apply to the synthesis of complex molecules such as natural products and APIs. Therefore, organic synthesis of such complex molecules has been conducted by batch methods. On the other hand, syntheses and reactions that attain high yields and high selectivities by flow methods are increasingly reported. Flow methods are leading candidates for the next generation of manufacturing methods that can mitigate environmental concerns toward sustainable society. PMID:26337828

  18. A Randomized Controlled Trial of Interventions to Impede Date Palm Sap Contamination by Bats to Prevent Nipah Virus Transmission in Bangladesh

    Science.gov (United States)

    Khan, Salah Uddin; Gurley, Emily S.; Hossain, M. Jahangir; Nahar, Nazmun; Sharker, M. A. Yushuf; Luby, Stephen P.

    2012-01-01

    Background Drinking raw date palm sap is a risk factor for human Nipah virus (NiV) infection. Fruit bats, the natural reservoir of NiV, commonly contaminate raw sap with saliva by licking date palm’s sap producing surface. We evaluated four types of physical barriers that may prevent bats from contacting sap. Methods During 2009, we used a crossover design and randomly selected 20 date palm sap producing trees and observed each tree for 2 nights: one night with a bamboo skirt intervention applied and one night without the intervention. During 2010, we selected 120 trees and randomly assigned four types of interventions to 15 trees each: bamboo, dhoincha (local plant), jute stick and polythene skirts covering the shaved part, sap stream, tap and collection pot. We enrolled the remaining 60 trees as controls. We used motion sensor activated infrared cameras to examine bat contact with sap. Results During 2009 bats contacted date palm sap in 85% of observation nights when no intervention was used compared with 35% of nights when the intervention was used [psap when the skirt did not entirely cover the sap producing surface. Therefore, in 2010 we requested the sap harvesters to use larger skirts. During 2010 bats contacted date palm sap [2% vs. 83%, psap in trees with bamboo (psap during one night (7%) with the jute stick skirt (psap producing areas of a tree effectively prevented bat-sap contact. Community interventions should promote applying these skirts to prevent occasional Nipah spillovers to human. PMID:22905160

  19. Vertical foliage distribution determines the radial pattern of sap flux density in Picea abies.

    Science.gov (United States)

    Fiora, Alessandro; Cescatti, Alessandro

    2008-09-01

    Understanding the causes determining the radial pattern of sap flux density is important both for improving knowledge of sapwood functioning and for up-scaling sap flow measurements to canopy transpiration and ecosystem water use. To investigate the anatomical connection between whorls and annual sapwood rings, pruning-induced variation in the radial pattern of sap flux density was monitored with Granier probes in a 35-year-old Picea abies (L.) Karst tree that was pruned from the crown bottom up. Modifications in the radial pattern of sap flux density were quantified by a shape index (SI), which varies with the relative contribution of the outer and inner sapwood to tree transpiration. The SI progressively diminished during bottom up pruning, indicating a significant reduction in sap flow contribution of the inner sapwood. Results suggest that the radial pattern of sap flux density depends mainly on the vertical distribution of foliage in the crown, with lower shaded branches hydraulically connected with inner sapwood and upper branches connected with the outer rings.

  20. Computational methods for internal flows with emphasis on turbomachinery

    Science.gov (United States)

    Mcnally, W. D.; Sockol, P. M.

    1981-01-01

    Current computational methods for analyzing flows in turbomachinery and other related internal propulsion components are presented. The methods are divided into two classes. The inviscid methods deal specifically with turbomachinery applications. Viscous methods, deal with generalized duct flows as well as flows in turbomachinery passages. Inviscid methods are categorized into the potential, stream function, and Euler aproaches. Viscous methods are treated in terms of parabolic, partially parabolic, and elliptic procedures. Various grids used in association with these procedures are also discussed.

  1. Ocular Blood Flow Autoregulation Mechanisms and Methods

    Directory of Open Access Journals (Sweden)

    Xue Luo

    2015-01-01

    Full Text Available The main function of ocular blood flow is to supply sufficient oxygen and nutrients to the eye. Local blood vessels resistance regulates overall blood distribution to the eye and can vary rapidly over time depending on ocular need. Under normal conditions, the relation between blood flow and perfusion pressure in the eye is autoregulated. Basically, autoregulation is a capacity to maintain a relatively constant level of blood flow in the presence of changes in ocular perfusion pressure and varied metabolic demand. In addition, ocular blood flow dysregulation has been demonstrated as an independent risk factor to many ocular diseases. For instance, ocular perfusion pressure plays key role in the progression of retinopathy such as glaucoma and diabetic retinopathy. In this review, different direct and indirect techniques to measure ocular blood flow and the effect of myogenic and neurogenic mechanisms on ocular blood flow are discussed. Moreover, ocular blood flow regulation in ocular disease will be described.

  2. Ocular Blood Flow Autoregulation Mechanisms and Methods

    OpenAIRE

    Xue Luo; Yu-meng Shen; Meng-nan Jiang; Xiang-feng Lou; Yin Shen

    2015-01-01

    The main function of ocular blood flow is to supply sufficient oxygen and nutrients to the eye. Local blood vessels resistance regulates overall blood distribution to the eye and can vary rapidly over time depending on ocular need. Under normal conditions, the relation between blood flow and perfusion pressure in the eye is autoregulated. Basically, autoregulation is a capacity to maintain a relatively constant level of blood flow in the presence of changes in ocular perfusion pressure and va...

  3. Seasonal and diel variation in xylem CO2 concentration and sap pH in sub-Mediterranean oak stems.

    Science.gov (United States)

    Salomón, Roberto; Valbuena-Carabaña, María; Teskey, Robert; McGuire, Mary Anne; Aubrey, Doug; González-Doncel, Inés; Gil, Luis; Rodríguez-Calcerrada, Jesús

    2016-04-01

    Since a substantial portion of respired CO2 remains within the stem, diel and seasonal trends in stem CO2 concentration ([CO2]) are of major interest in plant respiration and carbon budget research. However, continuous long-term stem [CO2] studies are scarce, and generally absent in Mediterranean climates. In this study, stem [CO2] was monitored every 15min together with stem and air temperature, sap flow, and soil water storage during a growing season in 16 stems of Quercus pyrenaica to elucidate the main drivers of stem [CO2] at different temporal scales. Fluctuations in sap pH were also assessed during two growing seasons to evaluate potential errors in estimates of the concentration of CO2 dissolved in xylem sap ([CO2*]) calculated using Henry's law. Stem temperature was the best predictor of stem [CO2] and explained more than 90% and 50% of the variability in stem [CO2] at diel and seasonal scales, respectively. Under dry conditions, soil water storage was the main driver of stem [CO2]. Likewise, the first rains after summer drought caused intense stem [CO2] pulses, suggesting enhanced stem and root respiration and increased resistance to radial CO2 diffusion. Sap flow played a secondary role in controlling stem [CO2] variations. We observed night-time sap pH acidification and progressive seasonal alkalinization. Thus, if the annual mean value of sap pH (measured at midday) was assumed to be constant, night-time sap [CO2*] was substantially overestimated (40%), and spring and autumn sap [CO2*] were misestimated by 25%. This work highlights that diel and seasonal variations in temperature, tree water availability, and sap pH substantially affect xylem [CO2] and sap [CO2*].

  4. Boundary integral methods for unsaturated flow

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, M.J.; McTigue, D.F.

    1990-12-31

    Many large simulations may be required to assess the performance of Yucca Mountain as a possible site for the nations first high level nuclear waste repository. A boundary integral equation method (BIEM) is described for numerical analysis of quasilinear steady unsaturated flow in homogeneous material. The applicability of the exponential model for the dependence of hydraulic conductivity on pressure head is discussed briefly. This constitutive assumption is at the heart of the quasilinear transformation. Materials which display a wide distribution in pore-size are described reasonably well by the exponential. For materials with a narrow range in pore-size, the exponential is suitable over more limited ranges in pressure head. The numerical implementation of the BIEM is used to investigate the infiltration from a strip source to a water table. The net infiltration of moisture into a finite-depth layer is well-described by results for a semi-infinite layer if {alpha}D > 4, where {alpha} is the sorptive number and D is the depth to the water table. the distribution of moisture exhibits a similar dependence on {alpha}D. 11 refs., 4 figs.,

  5. On methods of estimating cosmological bulk flows

    CERN Document Server

    Nusser, Adi

    2015-01-01

    We explore similarities and differences between several estimators of the cosmological bulk flow, $\\bf B$, from the observed radial peculiar velocities of galaxies. A distinction is made between two theoretical definitions of $\\bf B$ as a dipole moment of the velocity field weighted by a radial window function. One definition involves the three dimensional (3D) peculiar velocity, while the other is based on its radial component alone. Different methods attempt at inferring $\\bf B$ for either of these definitions which coincide only for a constant velocity field. We focus on the Wiener Filtering (WF, Hoffman et al. 2015) and the Constrained Minimum Variance (CMV,Feldman et al. 2010) methodologies. Both methodologies require a prior expressed in terms of the radial velocity correlation function. Hoffman et al. compute $\\bf B$ in Top-Hat windows from a WF realization of the 3D peculiar velocity field. Feldman et al. infer $\\bf B$ directly from the observed velocities for the second definition of $\\bf B$. The WF ...

  6. Morphometric methods for simulation of water flow.

    NARCIS (Netherlands)

    Booltink, H.W.G.

    1993-01-01

    Water flow in structured soils is strongly governed by the occurence of macropores. In this study emphasis was given to combined research of morphology of water- conducting macropores and soil physical measurements on bypass flow. Main research objectives were to: (i) develop and improve soil physic

  7. Effective methods for cash flow analysis.

    Science.gov (United States)

    Sylvestre, J; Urbancic, F R

    1994-07-01

    This article discusses techniques that healthcare financial managers can use to interpret and evaluate information from the statement of cash flows for more effective financial decision-making. The use of these techniques as a basis for systematically planning and controlling cash flows has the potential to benefit all healthcare organizations.

  8. Insects Attracted to Maple Sap: Observations from Prince Edward Island, Canada

    Directory of Open Access Journals (Sweden)

    Christopher Majka

    2010-07-01

    Full Text Available The collection of maple sap for the production of maple syrup is a large commercial enterprise in Canada and the United States. In Canada, which produces 85% of the world’s supply, it has an annual value of over $168 million CAD. Over 38 million trees are tapped annually, 6.5% of which use traditional buckets for sap collection. These buckets attract significant numbers of insects. Despite this, there has been very little investigation of the scale of this phenomenon and the composition of insects that are attracted to this nutrient source. The present paper reports the results of a preliminary study conducted on Prince Edward Island, Canada. Twenty-eight species of Coleoptera, Lepidoptera, and Trichoptera were found in maple sap buckets, 19 of which are known to be attracted to saps and nectars. The physiological role of sap feeding is discussed with reference to moths of the tribe Xylenini, which are active throughout the winter, and are well documented as species that feed on sap flows. Additionally, 18 of the 28 species found in this study are newly recorded in Prince Edward Island.

  9. 46 CFR 16.203 - Employer, MRO, and SAP responsibilities.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Employer, MRO, and SAP responsibilities. 16.203 Section... CHEMICAL TESTING Required Chemical Testing § 16.203 Employer, MRO, and SAP responsibilities. (a) Employers...) Substance Abuse Professional (SAP). Individuals performing SAP functions must meet the training requirements...

  10. PDF methods for turbulent reactive flows

    Science.gov (United States)

    Hsu, Andrew T.

    1995-01-01

    Viewgraphs are presented on computation of turbulent combustion, governing equations, closure problem, PDF modeling of turbulent reactive flows, validation cases, current projects, and collaboration with industry and technology transfer.

  11. CT measurements of SAP voids in concrete

    DEFF Research Database (Denmark)

    Laustsen, Sara; Bentz, Dale P.; Hasholt, Marianne Tange

    2010-01-01

    X-ray computed tomography (CT) scanning is used to determine the SAP void distribution in hardened concrete. Three different approaches are used to analyse a binary data set created from CT measurement. One approach classifies a cluster of connected, empty voxels (volumetric pixel of a 3D image......) as one void, whereas the other two approaches are able to classify a cluster of connected, empty voxels as a number of individual voids. Superabsorbent polymers (SAP) have been used to incorporate air into concrete. An advantage of using SAP is that it enables control of the amount and size...... of the created air voids. The results indicate the presence of void clusters. To identify the individual voids, special computational approaches are needed. The addition of SAP results in a dominant peak in two of the three air void distributions. Based on the position (void diameter) of the peak, it is possible...

  12. CT measurements of SAP voids in concrete

    DEFF Research Database (Denmark)

    Laustsen, Sara; Bentz, Dale P.; Hasholt, Marianne Tange;

    2010-01-01

    X-ray computed tomography (CT) scanning is used to determine the SAP void distribution in hardened concrete. Three different approaches are used to analyse a binary data set created from CT measurement. One approach classifies a cluster of connected, empty voxels (volumetric pixel of a 3D image......) as one void, whereas the other two approaches are able to classify a cluster of connected, empty voxels as a number of individual voids. Superabsorbent polymers (SAP) have been used to incorporate air into concrete. An advantage of using SAP is that it enables control of the amount and size...... of the created air voids. The results indicate the presence of void clusters. To identify the individual voids, special computational approaches are needed. The addition of SAP results in a dominant peak in two of the three air void distributions. Based on the position (void diameter) of the peak, it is possible...

  13. Field methods for measuring concentrated flow erosion

    Science.gov (United States)

    Castillo, C.; Pérez, R.; James, M. R.; Quinton, J. N.; Taguas, E. V.; Gómez, J. A.

    2012-04-01

    techniques (3D) for measuring erosion from concentrated flow (pole, laser profilemeter, photo-reconstruction and terrestrial LiDAR) The comparison between two- and three-dimensional methods has showed the superiority of the 3D techniques for obtaining accurate cross sectional data. The results from commonly-used 2D methods can be subject to systematic errors in areal cross section that exceed magnitudes of 10 % on average. In particular, the pole simplified method has showed a clear tendency to understimate areas. Laser profilemeter results show that further research on calibrating optical devices for a variety of soil conditions must be carried out to improve its performance. For volume estimations, photo-reconstruction results provided an excellent approximation to terrestrial laser data and demonstrate that this new remote sensing technique has a promising application field in soil erosion studies. 2D approaches involved important errors even over short measurement distances. However, as well as accuracy, the cost and time requirements of a technique must be considered.

  14. Nye integrerede ledelsesinformationssystemer SAP/R3

    DEFF Research Database (Denmark)

    Nielsen, Steen

    1998-01-01

    Artiklen beskriver og analyserer hovedindholdet i SAP/R3's controlling modul, speciel med sigte på hvilke forudsætninger systemet bygger på, dels med reference til den danske lønsomheds- og kapacitetsmodel.......Artiklen beskriver og analyserer hovedindholdet i SAP/R3's controlling modul, speciel med sigte på hvilke forudsætninger systemet bygger på, dels med reference til den danske lønsomheds- og kapacitetsmodel....

  15. Nye integrerede ledelsesinformationssystemer SAP/R3

    DEFF Research Database (Denmark)

    Nielsen, Steen

    1998-01-01

    Artiklen beskriver og analyserer hovedindholdet i SAP/R3's controlling modul, speciel med sigte på hvilke forudsætninger systemet bygger på, dels med reference til den danske lønsomheds- og kapacitetsmodel.......Artiklen beskriver og analyserer hovedindholdet i SAP/R3's controlling modul, speciel med sigte på hvilke forudsætninger systemet bygger på, dels med reference til den danske lønsomheds- og kapacitetsmodel....

  16. Cell-cell interaction in blood flow in patients with coronary heart disease (in vitro study)

    Science.gov (United States)

    Malinova, Lidia I.; Simonenko, Georgy V.; Denisova, Tatyana P.; Tuchin, Valery V.

    2007-02-01

    Blood cell-cell and cell-vessel wall interactions are one of the key patterns in blood and vascular pathophysiology. We have chosen the method of reconstruction of pulsative blood flow in vitro in the experimental set. Blood flow structure was studied by PC integrated video camera with following slide by slide analysis. Studied flow was of constant volumetric blood flow velocity (1 ml/h). Diameter of tube in use was comparable with coronary arteries diameter. Glucose solution and unfractured heparin were used as the nonspecial irritants of studied flow. Erythrocytes space structure in flow differs in all groups of patients in our study (men with stable angina pectoris (SAP), myocardial infarction (MI) and practically healthy men (PHM). Intensity of erythrocytes aggregate formation was maximal in patients with SAP, but time of their "construction/deconstruction" at glucose injection was minimal. Phenomena of primary clotting formation in patients with SAP of high function class was reconstructed under experimental conditions. Heparin injection (10 000 ED) increased linear blood flow velocity both in patients with SAP, MI and PHP but modulated the cell profile in the flow. Received data correspond with results of animal model studies and noninvasive blood flow studies in human. Results of our study reveal differences in blood flow structure in patients with coronary heart disease and PHP under irritating conditions as the possible framework of metabolic model of coronary blood flow destabilization.

  17. Frontier in nanoscale flows fractional calculus and analytical methods

    CERN Document Server

    Lewis, Roland; Liu, Hong-yan

    2014-01-01

    This ebook covers the basic properties of nanoscale flows, and various analytical and numerical methods for nanoscale flows and environmental flows. This ebook is a good reference not only for audience of the journal, but also for various communities in mathematics, nanotechnology and environmental science.

  18. Water Use Patterns of Four Tropical Bamboo Species Assessed with Sap Flux Measurements.

    Science.gov (United States)

    Mei, Tingting; Fang, Dongming; Röll, Alexander; Niu, Furong; Hendrayanto; Hölscher, Dirk

    2015-01-01

    Bamboos are grasses (Poaceae) that are widespread in tropical and subtropical regions. We aimed at exploring water use patterns of four tropical bamboo species (Bambusa vulgaris, Dendrocalamus asper, Gigantochloa atroviolacea, and G. apus) with sap flux measurement techniques. Our approach included three experimental steps: (1) a pot experiment with a comparison of thermal dissipation probes (TDPs), the stem heat balance (SHB) method and gravimetric readings using potted B. vulgaris culms, (2) an in situ calibration of TDPs with the SHB method for the four bamboo species, and (3) field monitoring of sap flux of the four bamboo species along with three tropical tree species (Gmelina arborea, Shorea leprosula, and Hevea brasiliensis) during a dry and a wet period. In the pot experiment, it was confirmed that the SHB method is well suited for bamboos but that TDPs need to be calibrated. In situ, species-specific parameters for such calibration formulas were derived. During field monitoring we found that some bamboo species reached high maximum sap flux densities. Across bamboo species, maximal sap flux density increased with decreasing culm diameter. In the diurnal course, sap flux densities in bamboos peaked much earlier than radiation and vapor pressure deficit (VPD), and also much earlier than sap flux densities in trees. There was a pronounced hysteresis between sap flux density and VPD in bamboos, which was less pronounced in trees. Three of the four bamboo species showed reduced sap flux densities at high VPD values during the dry period, which was associated with a decrease in soil moisture content. Possible roles of internal water storage, root pressure and stomatal sensitivity are discussed.

  19. Numerical modeling of microchannel gas flows in the transition flow regime via cascaded lattice Boltzmann method

    CERN Document Server

    Liu, Qing

    2016-01-01

    As a numerically accurate and computationally efficient mesoscopic numerical method, the lattice Boltzmann (LB) method has achieved great success in simulating microscale rarefied gas flows. In this paper, an LB method based on the cascaded collision operator is presented to simulate microchannel gas flows in the transition flow regime. The Bosanquet-type effective viscosity is incorporated into the cascaded lattice Boltzmann (CLB) method to account for the rarefaction effects. In order to gain accurate simulations and match the Bosanquet-type effective viscosity, the combined bounce-back/specular-reflection scheme with a modified second-order slip boundary condition is employed in the CLB method. The present method is applied to study gas flow in a microchannel with periodic boundary condition and gas flow in a long microchannel with pressure boundary condition over a wide range of Knudsen numbers. The predicted results, including the velocity profile, the mass flow rate, and the non-linear pressure deviatio...

  20. Hodograph method in MHD orthogonal fluid flows

    Directory of Open Access Journals (Sweden)

    P. V. Nguyen

    1992-01-01

    Full Text Available Equations for steady plane MHD orthogonal flows of a viscous incompressible fluid of finite electrical conductivity are recast in the hodograph plane by using the Legendre transform function of the streamfunction. Three examples are studied to illustrate the developed theory. Solutions and geometries for these examples are determined.

  1. A method of determining combustion gas flow

    Science.gov (United States)

    Bon Tempi, P. J.

    1968-01-01

    Zirconium oxide coating enables the determination of hot gas flow patterns on liquid rocket injector face and baffle surfaces to indicate modifications that will increase performance and improve combustion stability. The coating withstands combustion temperatures and due to the coarse surface and coloring of the coating, shows the hot gas patterns.

  2. Plant fluid proteomics: Delving into the xylem sap, phloem sap and apoplastic fluid proteomes

    Science.gov (United States)

    The phloem sap, xylem sap and apoplastic fluid play key roles in long and short distance transport of signals and nutrients, and act as a barrier against local and systemic pathogen infection. Among other components, these plant fluids contain proteins which are likely to be important players in the...

  3. Characterization of Vapor and Aerosol Flows by Photothermal Methods.

    Science.gov (United States)

    2014-09-26

    TECHNICAL REPORT No. 19 Characterization of Vapor and Aerosol Flows By Photothermal Methods by H. Sontag A. C. Tam IBM Research Laboratory San Jose...PERIOD COVERED Characterization of Vapor and Aerosol Flows Technical Report by Photothermal Methods S. PERFORMING OR. REPORT NUMBER 7. AUTHOR(a) S...related sciences, Montreal, 1985. I. KEY WORDS (Coilnue ..evrevers side II nscoomy ed idontlly by block nu.er) Photothermal , aerosol, flow, spectroscopy

  4. Allocation of Transmission Cost Using Power Flow Tracing Methods

    Directory of Open Access Journals (Sweden)

    CH Vishnu Vardhan Reddy

    2016-10-01

    Full Text Available In the open access restructured power system market, it is necessary to develop an appropriate pricing scheme that can provide the useful economic information to market participants, such as generation, transmission companies and customers. Though many methods have already been proposed, but accurately estimating and allocating the transmission cost in the transmission pricing scheme is still a challenging task. This work addresses the problem of allocating the cost of the transmission network to generators and demands. In this work four methods using DC Power flow and AC power flow have been attempted. They are MW-Mile Method, MVA-Mile Method, GGDF method and Bialek Tracing method.MVA-Mile method and Bialek Tracing method applies AC power flow and considers apparent power flows. The purpose of the present work is to allocate the cost pertaining to the transmission lines of the network to all the generators and demands. A load flow solution is run and, the proposed method determines how line flows depend on nodal currents. This result is then used to allocate network costs to generators and demands. The technique presented in this work is related to the allocation of the cost to GENCO‘s TRANSCO‘s and DISCO‘s. A technique for tracing the flow of electricity of lines among generators with GGDF and Bialek upstream looking algorithm is proposed. With these methods correct economic signals are generated for all players. All these methods are tested on IEEE 14 bus system

  5. Flow "Fine" Synthesis: High Yielding and Selective Organic Synthesis by Flow Methods.

    Science.gov (United States)

    Kobayashi, Shū

    2016-02-18

    The concept of flow "fine" synthesis, that is, high yielding and selective organic synthesis by flow methods, is described. Some examples of flow "fine" synthesis of natural products and APIs are discussed. Flow methods have several advantages over batch methods in terms of environmental compatibility, efficiency, and safety. However, synthesis by flow methods is more difficult than synthesis by batch methods. Indeed, it has been considered that synthesis by flow methods can be applicable for the production of simple gasses but that it is difficult to apply to the synthesis of complex molecules such as natural products and APIs. Therefore, organic synthesis of such complex molecules has been conducted by batch methods. On the other hand, syntheses and reactions that attain high yields and high selectivities by flow methods are increasingly reported. Flow methods are leading candidates for the next generation of manufacturing methods that can mitigate environmental concerns toward sustainable society. © 2015 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

  6. Methods for measurement of cerebral blood flow in man

    DEFF Research Database (Denmark)

    Lassen, N A

    1976-01-01

    A survey of the currently available methods for the measurement of cerebral blood flow in man is given. Many of the clinically important brain diseases such as tumors, stroke, brain trauma or epilepsy entail focal or regional flow alterations. Therefore a special emphasis is placed on methods all...

  7. Free-Surface Viscous Flow Solution Methods for Ship Hydrodynamics

    NARCIS (Netherlands)

    Wackers, J.; Koren, B.; Raven, H.C.; Ploeg, A. van der; Starke, A.R.; Deng, G.B.; Queutey, P.; Visonneau, M.; Hino, T.; Ohashi, K.

    2011-01-01

    The simulation of viscous free-surface water flow is a subject that has reached a certain maturity and is nowadays used in industrial applications, like the simulation of the flow around ships. While almost all methods used are based on the Navier-Stokes equations, the discretisation methods for the

  8. A fictitious domain method for particulate flows with heat transfer

    NARCIS (Netherlands)

    Yu, Z.; Yu, Zhaosheng; Shao, Xueming; Wachs, Anthony

    2006-01-01

    The distributed-Lagrange-multiplier/fictitious-domain (DLM/FD) method of Glowinski et al. [R. Glowinski, T.-W. Pan, T.I. Hesla, D.D. Joseph, A distributed Lagrange multiplier/fictitious domain method for particulate flows, Int. J. Multiphase Flow 25 (1999) 755–794] is extended to deal with heat

  9. A fictitious domain method for particulate flows with heat transfer

    NARCIS (Netherlands)

    Yu, Zhaosheng; Shao, Xueming; Wachs, Anthony

    2006-01-01

    The distributed-Lagrange-multiplier/fictitious-domain (DLM/FD) method of Glowinski et al. [R. Glowinski, T.-W. Pan, T.I. Hesla, D.D. Joseph, A distributed Lagrange multiplier/fictitious domain method for particulate flows, Int. J. Multiphase Flow 25 (1999) 755–794] is extended to deal with heat tran

  10. Integral methods for shallow free-surface flows with separation

    DEFF Research Database (Denmark)

    Watanabe, S.; Putkaradze, V.; Bohr, Tomas

    2003-01-01

    eddy and separated flow. Assuming a variable radial velocity profile as in Karman-Pohlhausen's method, we obtain a system of two ordinary differential equations for stationary states that can smoothly go through the jump. Solutions of the system are in good agreement with experiments. For the flow down......, and stationary jumps, obtained, for instance, behind a sluice gate. We then include time dependence in the model to study the stability of these waves. This allows us to distinguish between sub- and supercritical flows by calculating dispersion relations for wavelengths of the order of the width of the layer.......We study laminar thin film flows with large distortions of the free surface, using the method of averaging across the flow. Two specific problems are studied: the circular hydraulic jump and the flow down an inclined plane. For the circular hydraulic jump our method is able to handle an internal...

  11. Free-Surface Viscous Flow Solution Methods for Ship Hydrodynamics

    OpenAIRE

    WACKERS, Jeroen; Koren, Barry; Raven, H.C.; Van Der Ploeg,, Atze; Starke, A.R.; Deng, G.B.; Queutey, P.; VISONNEAU, Michel; Hino, T.; Ohashi, K

    2011-01-01

    The simulation of viscous free-surface water flow is a subject that has reached a certain maturity and is nowadays used in industrial applications, like the simulation of the flow around ships. While almost all methods used are based on the Navier-Stokes equations, the discretisation methods for the water surface differ widely. Many of these highly different methods are being used with success. We review three of these methods, by describing in detail their implementation in one particular co...

  12. Analysis list: SAP30 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available SAP30 Blood,Pluripotent stem cell + hg19 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/target/SAP...30.1.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/target/SAP30.5.tsv http://dbarchive....biosciencedbc.jp/kyushu-u/hg19/target/SAP30.10.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/colo/SAP...30.Blood.tsv,http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/colo/SAP30.Pluripote

  13. Ultrasonic 3-D vector flow method for quantitative in vivo peak velocity and flow rate estimation

    DEFF Research Database (Denmark)

    Holbek, Simon; Ewertsen, Caroline; Bouzari, Hamed;

    2017-01-01

    Current clinical ultrasound systems are limited to show blood flow movement in either 1-D or 2-D. In this paper, a method for estimating 3-D vector velocities in a plane using the Transverse Oscillation (TO) method, a 32 x 32 element matrix array, and the experimental ultrasound scanner SARUS...... is presented. The aim of this paper is to estimate precise flow rates and peak velocities derived from 3-D vector flow estimates. The emission sequence provides 3-D vector flow estimates at up to 1.145 frames per second in a plane, and was used to estimate 3-D vector flow in a cross sectional image plane....... The method is validated in two phantom studies, where flow rates are measured in a flow-rig, providing a constant parabolic flow, and in a straight-vessel phantom (ø = 8 mm) connected to a flow pump capable of generating time varying waveforms. Flow rates are estimated to be 82.1 ± 2.8 L/min in the flow...

  14. Lattice-Boltzmann Method for Geophysical Plastic Flows

    CERN Document Server

    Leonardi, Alessandro; Mendoza, Miller; Herrmann, Hans J

    2015-01-01

    We explore possible applications of the Lattice-Boltzmann Method for the simulation of geophysical flows. This fluid solver, while successful in other fields, is still rarely used for geotechnical applications. We show how the standard method can be modified to represent free-surface realization of mudflows, debris flows, and in general any plastic flow, through the implementation of a Bingham constitutive model. The chapter is completed by an example of a full-scale simulation of a plastic fluid flowing down an inclined channel and depositing on a flat surface. An application is given, where the fluid interacts with a vertical obstacle in the channel.

  15. Fourier time spectral method for subsonic and transonic flows

    Institute of Scientific and Technical Information of China (English)

    Lei Zhan; Feng Liu; Dimitri Papamoschou

    2016-01-01

    The time accuracy of the exponentially accu-rate Fourier time spectral method (TSM) is examined and compared with a conventional 2nd-order backward differ-ence formula (BDF) method for periodic unsteady flows. In particular, detailed error analysis based on numerical com-putations is performed on the accuracy of resolving the local pressure coefficient and global integrated force coefficients for smooth subsonic and non-smooth transonic flows with moving shock waves on a pitching airfoil. For smooth sub-sonic flows, the Fourier TSM method offers a significant accuracy advantage over the BDF method for the predic-tion of both the local pressure coefficient and integrated force coefficients. For transonic flows where the motion of the discontinuous shock wave contributes significant higher-order harmonic contents to the local pressure fluctuations, a sufficient number of modes must be included before the Fourier TSM provides an advantage over the BDF method. The Fourier TSM, however, still offers better accuracy than the BDF method for integrated force coefficients even for transonic flows. A problem of non-symmetric solutions for symmetric periodic flows due to the use of odd numbers of intervals is uncovered and analyzed. A frequency-searching method is proposed for problems where the frequency is not known a priori. The method is tested on the vortex shedding problem of the flow over a circular cylinder.

  16. Aortic blood flow subtraction: an alternative method for measuring total renal blood flow in conscious dogs

    DEFF Research Database (Denmark)

    Sandgaard, N C F; Andersen, J L; Holstein-Rathlou, N-H;

    2002-01-01

    We have measured total renal blood flow (TRBF) as the difference between signals from ultrasound flow probes implanted around the aorta above and below the renal arteries. The repeatability of the method was investigated by repeated, continuous infusions of angiotensin II and endothelin-1 seven...... arterial blood pressure by 49% and decreased TRBF by 12%, providing an increase in renal vascular resistance of 69%. Dynamic analysis showed autoregulation of renal blood flow in the frequency range ... of TRBF by aortic blood flow subtraction is a practical and reliable method that allows direct comparison of excretory function and renal blood flow from two kidneys. The method also allows direct comparison between TRBF and flow in the caudal aorta....

  17. Validation of the scale on Satisfaction of Adolescents with Postoperative pain management-idiopathic Scoliosis (SAP-S

    Directory of Open Access Journals (Sweden)

    Khadra C

    2017-01-01

    Full Text Available Christelle Khadra,1–3 Sylvie Le May,1,2 Ariane Ballard,1,2 Jean Théroux,1,4 Sylvie Charette,5 Edith Villeneuve,6,7 Stefan Parent,2,8,9 Argerie Tsimicalis,10,11 Jill MacLaren Chorney12,13 1Faculty of Nursing, Université de Montréal, 2CHU Sainte-Justine Research Centre, 3Montreal Chest Institute, McGill University Health Centre, Montreal, QC, Canada; 4School of Health Professions, Murdoch University, Perth, WA, Australia; 5Direction of Nursing, 6Department of Anesthesia, CHU Sainte-Justine, 7Department of Anesthesia, 8Department of Surgery, Faculty of Medicine, Université de Montréal, 9Orthopaedic Service, Department of Surgery, CHU Sainte-Justine, 10Ingram School of Nursing, McGill University, 11Shriners Hospitals for Children, Montreal, QC, 12Pediatric Complex Pain Team, IWK Health Centre, 13Department of Anesthesia, Pain Management, and Perioperative Medicine, Faculty of Medicine, Dalhousie University, Halifax, NS, Canada Background: Spinal fusion is a common orthopedic surgery in children and adolescents and is associated with high pain levels postoperatively. If the pain is not well managed, negative outcomes may ensue. To our knowledge, there is no measure in English that assesses patient’s satisfaction with postoperative pain management following idiopathic scoliosis surgery. The aim of the present study was to assess the psychometric properties of the satisfaction subscale of the English version of the Satisfaction of Adolescents with Postoperative pain management – idiopathic Scoliosis (SAP-S scale.Methods: Eighty-two participants aged 10–18 years, who had undergone spinal fusion surgery, fully completed the SAP-S scale at 10–14 days postdischarge. Construct validity was assessed through a principal component analysis using varimax rotation.Results: Principal component analysis indicated a three-factor structure of the 13-item satisfaction subscale of the SAP-S scale. Factors referred to satisfaction regarding current

  18. Polynomial interpolation methods for viscous flow calculations

    Science.gov (United States)

    Rubin, S. G.; Khosla, P. K.

    1977-01-01

    Higher-order collocation procedures which result in block-tridiagonal matrix systems are derived from (1) Taylor series expansions and from (2) polynomial interpolation, and the relationships between the two formulations, called respectively Hermite and spline collocation, are investigated. A Hermite block-tridiagonal system for a nonuniform mesh is derived, and the Hermite approach is extended in order to develop a variable-mesh sixth-order block-tridiagonal procedure. It is shown that all results obtained by Hermite development can be recovered by appropriate spline polynomial interpolation. The additional boundary conditions required for these higher-order procedures are also given. Comparative solutions using second-order accurate finite difference and spline and Hermite formulations are presented for the boundary layer on a flat plate, boundary layers with uniform and variable mass transfer, and the viscous incompressible Navier-Stokes equations describing flow in a driven cavity.

  19. Polynomial interpolation methods for viscous flow calculations

    Science.gov (United States)

    Rubin, S. G.; Khosla, P. K.

    1977-01-01

    Higher-order collocation procedures which result in block-tridiagonal matrix systems are derived from (1) Taylor series expansions and from (2) polynomial interpolation, and the relationships between the two formulations, called respectively Hermite and spline collocation, are investigated. A Hermite block-tridiagonal system for a nonuniform mesh is derived, and the Hermite approach is extended in order to develop a variable-mesh sixth-order block-tridiagonal procedure. It is shown that all results obtained by Hermite development can be recovered by appropriate spline polynomial interpolation. The additional boundary conditions required for these higher-order procedures are also given. Comparative solutions using second-order accurate finite difference and spline and Hermite formulations are presented for the boundary layer on a flat plate, boundary layers with uniform and variable mass transfer, and the viscous incompressible Navier-Stokes equations describing flow in a driven cavity.

  20. Finite difference methods for coupled flow interaction transport models

    Directory of Open Access Journals (Sweden)

    Shelly McGee

    2009-04-01

    Full Text Available Understanding chemical transport in blood flow involves coupling the chemical transport process with flow equations describing the blood and plasma in the membrane wall. In this work, we consider a coupled two-dimensional model with transient Navier-Stokes equation to model the blood flow in the vessel and Darcy's flow to model the plasma flow through the vessel wall. The advection-diffusion equation is coupled with the velocities from the flows in the vessel and wall, respectively to model the transport of the chemical. The coupled chemical transport equations are discretized by the finite difference method and the resulting system is solved using the additive Schwarz method. Development of the model and related analytical and numerical results are presented in this work.

  1. COMPUTATIONAL FLOW RATE FEEDBACK AND CONTROL METHOD IN HYDRAULIC ELEVATORS

    Institute of Scientific and Technical Information of China (English)

    Xu Bing; Ma Jien; Lin Jianjie

    2005-01-01

    The computational flow rate feedback and control method, which can be used in proportional valve controlled hydraulic elevators, is discussed and analyzed. In a hydraulic elevator with this method, microprocessor receives pressure information from the pressure transducers and computes the flow rate through the proportional valve based on pressure-flow conversion real time algorithm. This hydraulic elevator is of lower cost and energy consumption than the conventional closed loop control hydraulic elevator whose flow rate is measured by a flow meter. Experiments are carried out on a test rig which could simulate the load of hydraulic elevator. According to the experiment results, the means to modify the pressure-flow conversion algorithm are pointed out.

  2. Numerical method for a moving solid object in flows.

    Science.gov (United States)

    Yokoi, Kensuke

    2003-04-01

    We propose a numerical method for dealing with a moving solid body that interacts with a complex liquid surface. The method is based on the level set method, the CIP method, and the ghost fluid method. The validity of the method was shown by applying it to Poiseuille and Couette flow problems. The method can precisely capture the boundary layer as well as a moving solid object.

  3. Solving functional flow equations with pseudo-spectral methods

    CERN Document Server

    Borchardt, Julia

    2016-01-01

    We apply pseudo-spectral methods to integrate functional flow equations with high accuracy, extending earlier work on functional fixed point equations \\cite{Borchardt:2015rxa}. The advantages of our method are illustrated with the help of two classes of models: first, to make contact with literature, we investigate flows of the O$(N)$-model in 3 dimensions, for $N=1, 4$ and in the large $N$ limit. For the case of a fractal dimension, $d=2.4$, and $N=1$, we follow the flow along a separatrix from a multicritical fixed point to the Wilson-Fisher fixed point over almost 13 orders of magnitude. As a second example, we consider flows of bounded quantum-mechanical potentials, which can be considered as a toy model for Higgs inflation. Such flows pose substantial numerical difficulties, and represent a perfect test bed to exemplify the power of pseudo-spectral methods.

  4. A Reconstruction Method of Blood Flow Velocity in Left Ventricle Using Color Flow Ultrasound

    Directory of Open Access Journals (Sweden)

    Jaeseong Jang

    2015-01-01

    Full Text Available Vortex flow imaging is a relatively new medical imaging method for the dynamic visualization of intracardiac blood flow, a potentially useful index of cardiac dysfunction. A reconstruction method is proposed here to quantify the distribution of blood flow velocity fields inside the left ventricle from color flow images compiled from ultrasound measurements. In this paper, a 2D incompressible Navier-Stokes equation with a mass source term is proposed to utilize the measurable color flow ultrasound data in a plane along with the moving boundary condition. The proposed model reflects out-of-plane blood flows on the imaging plane through the mass source term. The boundary conditions to solve the system of equations are derived from the dimensions of the ventricle extracted from 2D echocardiography data. The performance of the proposed method is evaluated numerically using synthetic flow data acquired from simulating left ventricle flows. The numerical simulations show the feasibility and potential usefulness of the proposed method of reconstructing the intracardiac flow fields. Of particular note is the finding that the mass source term in the proposed model improves the reconstruction performance.

  5. Review of Upscaling Methods for Describing Unsaturated Flow

    Energy Technology Data Exchange (ETDEWEB)

    Wood, Brian D.

    2000-09-26

    Representing samll-scale features can be a challenge when one wants to model unsaturated flow in large domains. In this report, the various upscaling techniques are reviewed. The following upscaling methods have been identified from the literature: stochastic methods, renormalization methods, volume averaging and homogenization methods. In addition, a final technique, full resolution numerical modeling, is also discussed.

  6. Constrained blind deconvolution using Wirtinger flow methods

    KAUST Repository

    Walk, Philipp

    2017-09-04

    In this work we consider one-dimensional blind deconvolution with prior knowledge of signal autocorrelations in the classical framework of polynomial factorization. In particular this univariate case highly suffers from several non-trivial ambiguities and therefore blind deconvolution is known to be ill-posed in general. However, if additional autocorrelation information is available and the corresponding polynomials are co-prime, blind deconvolution is uniquely solvable up to global phase. Using lifting, the outer product of the unknown vectors is the solution to a (convex) semi-definite program (SDP) demonstrating that -theoretically- recovery is computationally tractable. However, for practical applications efficient algorithms are required which should operate in the original signal space. To this end we also discuss a gradient descent algorithm (Wirtinger flow) for the original non-convex problem. We demonstrate numerically that such an approach has performance comparable to the semidefinite program in the noisy case. Our work is motivated by applications in blind communication scenarios and we will discuss a specific signaling scheme where information is encoded into polynomial roots.

  7. PDF methods for combustion in high-speed turbulent flows

    Science.gov (United States)

    Pope, Stephen B.

    1995-01-01

    This report describes the research performed during the second year of this three-year project. The ultimate objective of the project is extend the applicability of probability density function (pdf) methods from incompressible to compressible turbulent reactive flows. As described in subsequent sections, progress has been made on: (1) formulation and modelling of pdf equations for compressible turbulence, in both homogeneous and inhomogeneous inert flows; and (2) implementation of the compressible model in various flow configurations, namely decaying isotropic turbulence, homogeneous shear flow and plane mixing layer.

  8. Construction of School Timetables by Flow Methods.

    Science.gov (United States)

    de Werra, D.

    In this paper, a heuristic algorithm for constructing school timetables is described. The algorithm is based on an exact method that applies to a family of particular timetable problems. The procedure has been used to construct timetables for Swiss schools having about 50 classes, 80 teachers, and 35 weekly periods. Less than five percent of…

  9. SAP ERP financial accounting and controlling configuration and use management

    CERN Document Server

    Okungbowa, Andrew

    2015-01-01

    SAP ERP modules are notoriously hard to configure and use effectively without a lot of practice and experience. But as SAP ERP Financial Accounting and Controlling: Configuration and Use Management shows, it doesn't have to be so difficult. The book takes a systematic approach that leads SAP Financial Accounting and Controlling (FICO) users step by step through configuring and using all the program's facets. This approach makes configuration complexities manageable. The book's author-SAP expert, trainer, and accountant Andrew Okun

  10. A flux monitoring method for easy and accurate flow rate measurement in pressure-driven flows.

    Science.gov (United States)

    Siria, Alessandro; Biance, Anne-Laure; Ybert, Christophe; Bocquet, Lydéric

    2012-03-07

    We propose a low-cost and versatile method to measure flow rate in microfluidic channels under pressure-driven flows, thereby providing a simple characterization of the hydrodynamic permeability of the system. The technique is inspired by the current monitoring method usually employed to characterize electro-osmotic flows, and makes use of the measurement of the time-dependent electric resistance inside the channel associated with a moving salt front. We have successfully tested the method in a micrometer-size channel, as well as in a complex microfluidic channel with a varying cross-section, demonstrating its ability in detecting internal shape variations.

  11. FINITE VOLUME METHOD OF MODELLING TRANSIENT GROUNDWATER FLOW

    Directory of Open Access Journals (Sweden)

    N. Muyinda

    2014-01-01

    Full Text Available In the field of computational fluid dynamics, the finite volume method is dominant over other numerical techniques like the finite difference and finite element methods because the underlying physical quantities are conserved at the discrete level. In the present study, the finite volume method is used to solve an isotropic transient groundwater flow model to obtain hydraulic heads and flow through an aquifer. The objective is to discuss the theory of finite volume method and its applications in groundwater flow modelling. To achieve this, an orthogonal grid with quadrilateral control volumes has been used to simulate the model using mixed boundary conditions from Bwaise III, a Kampala Surburb. Results show that flow occurs from regions of high hydraulic head to regions of low hydraulic head until a steady head value is achieved.

  12. DEMONSTRATION BULLETIN: COLLOID POLISHING FILTER METHOD - FILTER FLOW TECHNOLOGY, INC.

    Science.gov (United States)

    The Filter Flow Technology, Inc. (FFT) Colloid Polishing Filter Method (CPFM) was tested as a transportable, trailer mounted, system that uses sorption and chemical complexing phenomena to remove heavy metals and nontritium radionuclides from water. Contaminated waters can be pro...

  13. Pressure algorithm for elliptic flow calculations with the PDF method

    Science.gov (United States)

    Anand, M. S.; Pope, S. B.; Mongia, H. C.

    1991-01-01

    An algorithm to determine the mean pressure field for elliptic flow calculations with the probability density function (PDF) method is developed and applied. The PDF method is a most promising approach for the computation of turbulent reacting flows. Previous computations of elliptic flows with the method were in conjunction with conventional finite volume based calculations that provided the mean pressure field. The algorithm developed and described here permits the mean pressure field to be determined within the PDF calculations. The PDF method incorporating the pressure algorithm is applied to the flow past a backward-facing step. The results are in good agreement with data for the reattachment length, mean velocities, and turbulence quantities including triple correlations.

  14. 49 CFR 655.52 - Substance abuse professional (SAP).

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 7 2010-10-01 2010-10-01 false Substance abuse professional (SAP). 655.52 Section 655.52 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL TRANSIT... OPERATIONS Drug and Alcohol Testing Procedures § 655.52 Substance abuse professional (SAP). The SAP must...

  15. Computational methods for two-phase flow and particle transport

    CERN Document Server

    Lee, Wen Ho

    2013-01-01

    This book describes mathematical formulations and computational methods for solving two-phase flow problems with a computer code that calculates thermal hydraulic problems related to light water and fast breeder reactors. The physical model also handles the particle and gas flow problems that arise from coal gasification and fluidized beds. The second part of this book deals with the computational methods for particle transport.

  16. SAP GUI PM系统的GuiXT优化%Optimization of the SAP GUI PM module

    Institute of Scientific and Technical Information of China (English)

    兰祎天

    2012-01-01

    GuiXT is a software client-server-based tool which provides user interface customization solution for SAP applications.With experience in the use of SAP PM Module,the author of this article optimized the established program and showed%GuiXT是一个基于用户端-服务端的工具软件,其针对SAP应用提供用户界面定制化解决方案。作者结合SAP PM模块使用经验,利用仪化SAP系统自带的GuiXT程序对既定程序做出改进,通过应用案例,对SAP GUI程序操作进行了优化介绍。

  17. Protein extraction from xylem and phloem sap.

    Science.gov (United States)

    Kehr, Julia; Rep, Martijn

    2007-01-01

    It is well known that phloem and xylem vessels transport small nutrient molecules over long distances in higher plants. The finding that proteins also occur in both transport fluids was unexpected, and the function of most of these proteins is not yet well understood. This chapter outlines how proteins can be obtained and purified from xylem and phloem saps to perform subsequent proteomic analyses.

  18. Surface Absorption Polarization Sensors (SAPS), Final Technical Report, Laser Probing of Immobilized SAPS Actuators Component

    Energy Technology Data Exchange (ETDEWEB)

    Joseph I. Cline

    2010-04-22

    A novel hypothesized detection scheme for the detection of chemical agents was proposed: SAPS ``Surface-Adsorbed Polarization Sensors''. In this technique a thin layer of molecular rotors is adsorbed to a surface. The rotors can be energized by light absorption, but are otherwise locked in position or alternatively rotate slowly. Using polarized light, the adsorbed rotors are turned as an ensemble. Chemical agent (analyte) binding that alters the rotary efficiency would be detected by sensitive polarized absorption techniques. The mechanism of the SAPS detection can be mechanical, chemical, or photochemical: only a change in rotary efficiency is required. To achieve the goal of SAPS detection, new spectroscopic technique, polarized Normal Incidence Cavity Ringdown Spectroscopy (polarized NICRDS), was developed. The technique employs very sensitive and general Cavity Ringdown absorption spectroscopy along with the ability to perform polarized absorption measurements. Polarized absorption offers the ability to measure the angular position of molecular chromophores. In the new experiments a thin layer of SAPS sensors (roughly corresponding to a monolayer coverage on a surface) immobilized in PMMA. The PMMA layer is less than 100~nm thick and is spin-coated onto a flat fused-silica substrate. The new technique was applied to study the photoisomerization-driven rotary motion of a family of SAPS actuators based on a family of substituted dibenzofulvene rotors based upon 9-(2,2,2- triphenylethylidene)fluorene. By varying the substitution to include moieties such as nitro, amino, and cyano the absorption spectrum and the quantum efficiency of photoisomerization can be varied. This SAPS effect was readily detected by polarized NICRDS. The amino substituted SAPS actuator binds H+ to form an ammonium species which was shown to have a much larger quantum efficiency for photoisomerization. A thin layer of immobilized amino actuators were then shown by polarized NICRDS

  19. Targeting and cytotoxicity of SapC-DOPS nanovesicles in pancreatic cancer.

    Directory of Open Access Journals (Sweden)

    Zhengtao Chu

    Full Text Available Only a small number of promising drugs target pancreatic cancer, which is the fourth leading cause of cancer deaths with a 5-year survival of less than 5%. Our goal is to develop a new biotherapeutic agent in which a lysosomal protein (saposin C, SapC and a phospholipid (dioleoylphosphatidylserine, DOPS are assembled into nanovesicles (SapC-DOPS for treating pancreatic cancer. A distinguishing feature of SapC-DOPS nanovesicles is their high affinity for phosphatidylserine (PS rich microdomains, which are abnormally exposed on the membrane surface of human pancreatic tumor cells. To evaluate the role of external cell PS, in vitro assays were used to correlate PS exposure and the cytotoxic effect of SapC-DOPS in human tumor and nontumorigenic pancreatic cells. Next, pancreatic tumor xenografts (orthotopic and subcutaneous models were used for tumor targeting and therapeutic efficacy studies with systemic SapC-DOPS treatment. We observed that the nanovesicles selectively killed human pancreatic cancer cells in vitro by inducing apoptotic death, whereas untransformed cells remained unaffected. This in vitro cytotoxic effect correlated to the surface exposure level of PS on the tumor cells. Using xenografts, animals treated with SapC-DOPS showed clear survival benefits and their tumors shrank or disappeared. Furthermore, using a double-tracking method in live mice, we showed that the nanovesicles were specifically targeted to orthotopically-implanted, bioluminescent pancreatic tumors. These data suggest that the acidic phospholipid PS is a biomarker for pancreatic cancer that can be effectively targeted for therapy utilizing cancer-selective SapC-DOPS nanovesicles. This study provides convincing evidence in support of developing a new therapeutic approach to pancreatic cancer.

  20. The Inter-Rater Reliability of Simplified Acute Physiology Score 3 (SAPS3 among Intensive Care Unit Nurses

    Directory of Open Access Journals (Sweden)

    Jun Hyun Kim

    Full Text Available Background: Simplified acute physiology score 3 (SAPS3 was developed in 2005 to evaluate intensive care unit (ICU performance and to predict patient mortality or disease severity. The score is usually calculated by doctors, but it requires substantial human resources. And many nurse-lead studies use this scoring system. In the present study, we examined the inter-rater reliability of SAPS3 among nurses in an ICU. Methods: Five ICU nurses who worked in an ICU for a mean length of 7.8 years were educated for 2 hours about SAPS3 score and its components. Each nurse scored 26 patients, and the intraclass correlation coefficient (ICC of the total scores and each subset were evaluated. Results: The ICC (95% confidence interval of SAPS3 score was 0.89 (0.82-0.95, that of subset I was 0.90 (0.82-0.95, subset II was 0.54 (0.35-0.73, and subset III was 0.95 (0.91-0.97. The ICC of predicted mortality was 0.91 (0.85-0.96. Conclusions: The ICC of SAPS3 score and predicted mortality among ICU nurses were reliable. According to these ICC values, SAPS3 score is a reliable scale to be used by nurses. The ICC of subset II was lower than those of the other subsets, suggesting that education of SAPS3 should focus on the definition of each subset II component.

  1. Dissolved atmospheric gas in xylem sap measured with membrane inlet mass spectrometry.

    Science.gov (United States)

    Schenk, H Jochen; Espino, Susana; Visser, Ate; Esser, Bradley K

    2016-04-01

    A new method is described for measuring dissolved gas concentrations in small volumes of xylem sap using membrane inlet mass spectrometry. The technique can be used to determine concentrations of atmospheric gases, such as argon, as reported here, or for any dissolved gases and their isotopes for a variety of applications, such as rapid detection of trace gases from groundwater only hours after they were taken up by trees and rooting depth estimation. Atmospheric gas content in xylem sap directly affects the conditions and mechanisms that allow for gas removal from xylem embolisms, because gas can dissolve into saturated or supersaturated sap only under gas pressure that is above atmospheric pressure. The method was tested for red trumpet vine, Distictis buccinatoria (Bignoniaceae), by measuring atmospheric gas concentrations in sap collected at times of minimum and maximum daily temperature and during temperature increase and decline. Mean argon concentration in xylem sap did not differ significantly from saturation levels for the temperature and pressure conditions at any time of collection, but more than 40% of all samples were supersaturated, especially during the warm parts of day. There was no significant diurnal pattern, due to high variability between samples.

  2. Sap flow simulation of Cunninghamia lanceolata in degraded red soil region based on back propagation neural network%基于反向传播神经网络的退化红壤区杉木树干液流模拟

    Institute of Scientific and Technical Information of China (English)

    涂洁; 刘琪璟; 危骏; 胡良

    2015-01-01

    以江西退化红壤区杉木人工林为研究对象,采用MATLAB工具箱中的log‐sigmoid型函数( tansig)为神经元作用函数,以空气温度、空气相对湿度、平均净辐射、水汽压亏缺为输入变量,液流速率为输出变量,运用贝叶斯正则化算法和Levenberg‐Marquardt算法对4000组气象数据和液流数据进行网络训练和检验,构建拓扑结构为4101的杉木树干液流反向传播( back propagation , BP)神经网络模型.结果表明:在2种算法下训练样本和检验样本模型输出值与实测值之间线性回归的拟合程度均较高,回归方程的相关系数在0.93以上;训练样本的拟合精度分别为83.57%和83.06%,检验样本的仿真精度分别为82.87%和82.15%.说明该网络模型能够很好地反映液流速率与气象因子之间的非线性函数关系,可为杉木人工林的可持续经营和林地水资源的科学管理提供有效手段.%Summary Cunninghamia lanceolata is commonly considered to be one of the most important tree species for forest restoration and reconstruction in subtropical area of China , owing to its advantages of rapid growth , good quality and high yield per unit area . However , they also consume certain amount of water during the course of growth and play roles of ecological benefits . Therefore , quantitative research on tree water consumption characteristics by transpiration has become a hot issue in the field of tree physiological ecology in recent years . Taking the C . lanceolata plantation in degraded red soil of Jiangxi Province as the research object , the log‐sigmoid type function ( tansig) of MATLAB toolbox was selected as the transmission function for the role of neurons . Four main factors including air temperature , relative air humidity , average net radiation and vapor pressure deficit were chosen as the input variables , and the sap flow velocity was selected as the output variable , to train and

  3. A study of methods to estimate debris flow velocity

    Science.gov (United States)

    Prochaska, A.B.; Santi, P.M.; Higgins, J.D.; Cannon, S.H.

    2008-01-01

    Debris flow velocities are commonly back-calculated from superelevation events which require subjective estimates of radii of curvature of bends in the debris flow channel or predicted using flow equations that require the selection of appropriate rheological models and material property inputs. This research investigated difficulties associated with the use of these conventional velocity estimation methods. Radii of curvature estimates were found to vary with the extent of the channel investigated and with the scale of the media used, and back-calculated velocities varied among different investigated locations along a channel. Distinct populations of Bingham properties were found to exist between those measured by laboratory tests and those back-calculated from field data; thus, laboratory-obtained values would not be representative of field-scale debris flow behavior. To avoid these difficulties with conventional methods, a new preliminary velocity estimation method is presented that statistically relates flow velocity to the channel slope and the flow depth. This method presents ranges of reasonable velocity predictions based on 30 previously measured velocities. ?? 2008 Springer-Verlag.

  4. A new CFD modeling method for flow blockage accident investigations

    Energy Technology Data Exchange (ETDEWEB)

    Fan, Wenyuan, E-mail: fanwy@mail.ustc.edu.cn; Peng, Changhong, E-mail: pengch@ustc.edu.cn; Chen, Yangli, E-mail: chenyl@mail.ustc.edu.cn; Guo, Yun, E-mail: guoyun79@ustc.edu.cn

    2016-07-15

    Highlights: • Porous-jump treatment is applied to CFD simulation on flow blockages. • Porous-jump treatment predicts consistent results with direct CFD treatment. • Relap5 predicts abnormal flow rate profiles in MTR SFA blockage scenario. • Relap5 fails to simulate annular heat flux in blockage case of annular assembly. • Porous-jump treatment provides reasonable and generalized CFD results. - Abstract: Inlet flow blockages in both flat and annular plate-type fuel assemblies are simulated by (Computational Fluid Dynamics) CFD and system analysis methods, with blockage ratio ranging from 60 to 90%. For all the blockage scenarios, mass flow rate of the blocked channel drops dramatically as blockage ratio increases, while mass flow rates of non-blocked channels are almost steady. As a result of over-simplifications, the system code fails to capture details of mass flow rate profiles of non-blocked channels and power redistribution of fuel plates. In order to acquire generalized CFD results, a new blockage modeling method is developed by using the porous-jump condition. For comparisons, direct CFD simulations are conducted toward postulated blockages. For the porous-jump treatment, conservative flow and heat transfer conditions are predicted for the blocked channel, while consistent predictions are obtained for non-blocked channels. Besides, flow fields in the blocked channel, asymmetric power redistributions of fuel plates, and complex heat transfer phenomena in annular fuel assembly are obtained and discussed. The present study indicates that the porous-jump condition is a reasonable blockage modeling method, which predicts generalized CFD results for flow blockages.

  5. Predictive value of SAPS II and APACHE II scoring systems for patient outcome in a medical intensive care unit

    Directory of Open Access Journals (Sweden)

    Amina Godinjak

    2016-11-01

    Full Text Available Objective. The aim is to determine SAPS II and APACHE II scores in medical intensive care unit (MICU patients, to compare them for prediction of patient outcome, and to compare with actual hospital mortality rates for different subgroups of patients. Methods. One hundred and seventy-four patients were included in this analysis over a oneyear period in the MICU, Clinical Center, University of Sarajevo. The following patient data were obtained: demographics, admission diagnosis, SAPS II, APACHE II scores and final outcome. Results. Out of 174 patients, 70 patients (40.2% died. Mean SAPS II and APACHE II scores in all patients were 48.4±17.0 and 21.6±10.3 respectively, and they were significantly different between survivors and non-survivors. SAPS II >50.5 and APACHE II >27.5 can predict the risk of mortality in these patients. There was no statistically significant difference in the clinical values of SAPS II vs APACHE II (p=0.501. A statistically significant positive correlation was established between the values of SAPS II and APACHE II (r=0.708; p=0.001. Patients with an admission diagnosis of sepsis/septic shock had the highest values of both SAPS II and APACHE II scores, and also the highest hospital mortality rate of 55.1%. Conclusion. Both APACHE II and SAPS II had an excellent ability to discriminate between survivors and non-survivors. There was no significant difference in the clinical values of SAPS II and APACHE II. A positive correlation was established between them. Sepsis/septic shock patients had the highest predicted and observed hospital mortality rate.

  6. Clearance gap flow: simulations by discontinuous Galerkin method and experiments

    Directory of Open Access Journals (Sweden)

    Prausová Helena

    2015-01-01

    Full Text Available Compressible viscous fluid flow in a narrow gap formed by two parallel plates in distance of 2 mm is investigated numerically and experimentally. Pneumatic and optical methods were used to obtain distribution of static to stagnation pressure ratio along the channel axis and interferograms including the free outflow behind the channel. Modern developing discontinuous Galerkin finite element method is implemented for numerical simulation of the fluid flow. The goal to make progress in knowledge of compressible viscous fluid flow characteristic phenomena in minichannels is satisfied by finding a suitable approach to this problem. Laminar, turbulent and transitional flow regime is examined and a good agreement of experimental and numerical results is achieved using γ − Reθt transition model.

  7. Clearance gap flow: simulations by discontinuous Galerkin method and experiments

    Science.gov (United States)

    Prausová, Helena; Bublík, Ondřej; Vimmr, Jan; Luxa, Martin; Hála, Jindřich

    2015-05-01

    Compressible viscous fluid flow in a narrow gap formed by two parallel plates in distance of 2 mm is investigated numerically and experimentally. Pneumatic and optical methods were used to obtain distribution of static to stagnation pressure ratio along the channel axis and interferograms including the free outflow behind the channel. Modern developing discontinuous Galerkin finite element method is implemented for numerical simulation of the fluid flow. The goal to make progress in knowledge of compressible viscous fluid flow characteristic phenomena in minichannels is satisfied by finding a suitable approach to this problem. Laminar, turbulent and transitional flow regime is examined and a good agreement of experimental and numerical results is achieved using γ - Reθt transition model.

  8. Fiber optic liquid mass flow sensor and method

    Science.gov (United States)

    Korman, Valentin (Inventor); Gregory, Don Allen (Inventor); Wiley, John T. (Inventor); Pedersen, Kevin W. (Inventor)

    2010-01-01

    A method and apparatus are provided for sensing the mass flow rate of a fluid flowing through a pipe. A light beam containing plural individual wavelengths is projected from one side of the pipe across the width of the pipe so as to pass through the fluid under test. Fiber optic couplers located at least two positions on the opposite side of the pipe are used to detect the light beam. A determination is then made of the relative strengths of the light beam for each wavelength at the at least two positions and based at least in part on these relative strengths, the mass flow rate of the fluid is determined.

  9. A particle-based method for granular flow simulation

    KAUST Repository

    Chang, Yuanzhang

    2012-03-16

    We present a new particle-based method for granular flow simulation. In the method, a new elastic stress term, which is derived from a modified form of the Hooke\\'s law, is included in the momentum governing equation to handle the friction of granular materials. Viscosity force is also added to simulate the dynamic friction for the purpose of smoothing the velocity field and further maintaining the simulation stability. Benefiting from the Lagrangian nature of the SPH method, large flow deformation can be well handled easily and naturally. In addition, a signed distance field is also employed to enforce the solid boundary condition. The experimental results show that the proposed method is effective and efficient for handling the flow of granular materials, and different kinds of granular behaviors can be well simulated by adjusting just one parameter. © 2012 Science China Press and Springer-Verlag Berlin Heidelberg.

  10. Method of detaching adherent cells for flow cytometry

    KAUST Repository

    Kaur, Mandeep

    2015-12-24

    In one aspect, a method for detaching adherent cells can include adding a cell lifting solution to the media including a sample of adherent cells and incubating the sample of adherent cells with the cell lifting solution. No scraping or pipetting is needed to facilitate cell detachment. The method do not require inactivation of cell lifting solution and no washing of detaching cells is required to remove cell lifting solution. Detached cells can be stained with dye in the presence of cell lifting solution and are further analyzed using flow cytometer. The method has been tested using 6 different cell lines, 4 different assays, two different plate formats (96 and 384 well plates) and two different flow cytometry instruments. The method is simple to perform, less time consuming, with no cell loss and makes high throughput flow cytometry on adherent cells a reality.

  11. Flow imaging method of electromagnetic measurement in well logging

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Multiphase flow in an oil well is a dynamic phenomenon of inhomogeneous medium,which should be studied in a nonlinear way. This paper presents an electromagnetic measurement method based on the electrical property differences between oil,gas and water to scan,inverse and show the distribution and condition of multiphase flow. Both numerical simulation and physical experiments have proved that clear images could be obtained by this way.

  12. Study of the Transition Flow Regime using Monte Carlo Methods

    Science.gov (United States)

    Hassan, H. A.

    1999-01-01

    This NASA Cooperative Agreement presents a study of the Transition Flow Regime Using Monte Carlo Methods. The topics included in this final report are: 1) New Direct Simulation Monte Carlo (DSMC) procedures; 2) The DS3W and DS2A Programs; 3) Papers presented; 4) Miscellaneous Applications and Program Modifications; 5) Solution of Transitional Wake Flows at Mach 10; and 6) Turbulence Modeling of Shock-Dominated Fows with a k-Enstrophy Formulation.

  13. Start-to-end global imaging as a sunward propagating, SAPS-associated giant undulation event

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, Michael G [Los Alamos National Laboratory; Donovan, Eric F [U OF CALGARY; Foster, John C [MIT; Mann, Ian R [UNIV OF ALBERTA; Immel, Thomas J [UC/BERKELEY; Mende, Stephen B [UN/BERKELEY; Sigwarth, John B [NASA/GSFC

    2009-01-01

    We present high-time resolution global imaging of a sunward propagating giant undulation event from start to finish. The event occurred on November 24, 2001 during a very disturbed storm interval. The giant undulations began to develop at around 13UT and persisted for approximately 2 hours. The sunward propagation speed was on the order of 0.6 km/s (relative to SM coordinate system). The undulations had a wavelength of {approx} 750 km, amplitudes of {approx} 890 km and produced ULF pulsations on the ground with a period of {approx} 1108s. We show that the undulations were associated with SAPs flows that were caused by the proton plasma sheet penetrating substantially farther Earthward than the electron plasma sheet on the duskside. The observations appear to be consistent with the development of a shear flow and/or ballooning type of instability at the plasmapause driven by intense SAPS-associated shear flows.

  14. An update on projection methods for transient incompressible viscous flow

    Energy Technology Data Exchange (ETDEWEB)

    Gresho, P.M.; Chan, S.T.

    1995-07-01

    Introduced in 1990 was the biharmonic equation (for the pressure) and the concomitant biharmonic miracle when transient incompressible viscous flow is solved approximately by a projection method. Herein is introduced the biharmonic catastrophe that sometimes occurs with these same projection methods.

  15. Application of Lattice Boltzmann Method to Flows in Microgeometries

    Directory of Open Access Journals (Sweden)

    Anoop K. Dass

    2010-07-01

    Full Text Available In the present investigation, Lattice Boltzmann Method (LBM is used to simulate rarefied gaseous microflows in three microgeometries. These are micro-couette, micro lid-driven cavity and micro-poiseuille flows. The Knudsen number is used to measure the degree of rarefaction in the microflows. First, micro-couette flow is computed with the effects of varying Knudsen number in the slip and threshold of the transition regime and the results compare well with existing results. After having thus established the credibility of the code and the method including boundary conditions, LBM is then used to investigate the micro lid-driven cavity flow with various aspect ratios. Simulation of microflow not only requires an appropriate method, it also requires suitable boundary conditions to provide a well-posed problem and unique solution. In this work, LBM and three slip boundary conditions, namely, diffuse scattering boundary condition, specular reflection and a combination of bounce-back and specular reflection is used to predict the micro lid-driven cavity flow fields. Then the LBM simulation is extended to micro-poiseuille flow. The results are substantiated through comparison with existing results and it is felt that the present methodology is reasonable to be employed in analyzing the flow in micro-systems.

  16. Integral methods for shallow free-surface flows with separation

    CERN Document Server

    Watanabe, S; Bohr, T; Watanabe, Shinya; Putkaradze, Vachtang; Bohr, Tomas

    2000-01-01

    We study laminar thin film flows with large distortions in the free surface using the method of averaging across the flow. Two concrete problems are studied: the circular hydraulic jump and the flow down an inclined plane. For the circular hydraulic jump our method is able to handle an internal eddy and separated flow. Assuming a variable radial velocity profile like in Karman-Pohlhausen's method, we obtain a system of two ordinary differential equations for stationary states that can smoothly go through the jump where previous studies encountered a singularity. Solutions of the system are in good agreement with experiments. For the flow down an inclined plane we take a similar approach and derive a simple model in which the velocity profile is not restricted to a parabolic or self-similar form. Two types of solutions with large surface distortions are found: solitary, kink-like propagating fronts, obtained when the flow rate is suddenly changed, and stationary jumps, obtained, e.g., behind a sluice gate. We ...

  17. Buoy Relay Method for Instantaneous Fluid Flow with Free Surface

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Several methods have been used to approximate free surface boundaries in finite-difference numerical simulations. Each of these methods has its advantages and disadvantages. This paper presents a new technique for the numerical solution of transient incompressible free surface fluid flows. This powerful method, which is based on the concepts of "Buoy positioning" and "Buoy relaying", successfully represents the free surface using a Lagrangian method on a Eulerian grid by directly solving the free surface evolution equation. The Eulerian finite-difference forms of the full Navier-Stokes equations are solved by the Successive over Relaxation (SOR) method with a set of buoys to keep track of the free surface. The capabilities of the analysis procedure are demonstrated through viscous free surface fluid flow examples. The method is simpler and more efficient than other methods especially in treating complicated free boundary configurations.

  18. Meshless lattice Boltzmann method for the simulation of fluid flows.

    Science.gov (United States)

    Musavi, S Hossein; Ashrafizaadeh, Mahmud

    2015-02-01

    A meshless lattice Boltzmann numerical method is proposed. The collision and streaming operators of the lattice Boltzmann equation are separated, as in the usual lattice Boltzmann models. While the purely local collision equation remains the same, we rewrite the streaming equation as a pure advection equation and discretize the resulting partial differential equation using the Lax-Wendroff scheme in time and the meshless local Petrov-Galerkin scheme based on augmented radial basis functions in space. The meshless feature of the proposed method makes it a more powerful lattice Boltzmann solver, especially for cases in which using meshes introduces significant numerical errors into the solution, or when improving the mesh quality is a complex and time-consuming process. Three well-known benchmark fluid flow problems, namely the plane Couette flow, the circular Couette flow, and the impulsively started cylinder flow, are simulated for the validation of the proposed method. Excellent agreement with analytical solutions or with previous experimental and numerical results in the literature is observed in all the simulations. Although the computational resources required for the meshless method per node are higher compared to that of the standard lattice Boltzmann method, it is shown that for cases in which the total number of nodes is significantly reduced, the present method actually outperforms the standard lattice Boltzmann method.

  19. Proposed method for measurement of flow rate in turbulent periodic pipe flow

    Science.gov (United States)

    Werzner, E.; Ray, S.; Trimis, D.

    2011-12-01

    The present investigation deals with a previously proposed flow metering technique for laminar, fully-developed, time-periodic pipe flow. Employing knowledge of the pulsation frequency-dependent relationship between the mass flow rate and the pressure gradient, the method allows reconstruction of the instantaneous mass flow rate on the basis of a recorded pressure gradient time series. In order to explore if the procedure can be extended for turbulent flows, numerical simulations for turbulent, fully-developed, sinusoidally pulsating pipe flow with low pulse amplitude have been carried out using a ν2-f turbulence model. The study covers pulsation frequencies, ranging from the quasi-steady up to the inertia-dominated frequency regime, and three cycle-averaged Reynolds numbers of 4360, 9750 and 15400. After providing the theoretical background of the flow rate reconstruction principle, the numerical model and an experimental facility for the verification of simulations are explained. The obtained results, presented in time and frequency domain, show good agreement with each other and indicate a frequency dependence, similar to that used for the signal reconstruction for laminar flows. A modified dimensionless frequency definition has been introduced, which allows a generalised representation of the results considering the influence of Reynolds number.

  20. Keratouveitis caused by Euphorbia plant sap

    Directory of Open Access Journals (Sweden)

    Basak Samar

    2009-01-01

    Full Text Available The milky sap or latex of Euphorbia plant is highly toxic and an irritant to the skin and eye. This report illustrates the spectrum of ocular inflammation caused by accidental inoculation of latex of Euphorbia plant. Three patients presented with accidental ocular exposure to the milky sap of Euphorbia species of recent onset. The initial symptoms in all cases were severe burning sensation with blurring of vision. Visual acuity reduced from 20/60 to counting fingers. Clinical findings varied from kerato-conjunctivitis, mild to severe corneal edema, epithelial defects, anterior uveitis and secondary elevated intraocular pressure. All symptoms and signs had resolved by 10-14 days with active supportive medication. People who handle Euphorbia plants should wear eye protection. It is always advisable to ask the patient to bring a sample of the plant for identification.

  1. Mixed exhaust flow supersonic jet engine and method

    Energy Technology Data Exchange (ETDEWEB)

    Klees, G.W.

    1993-06-08

    A method of operating a supersonic jet engine installation is described comprising (a) providing an engine having a variable area air inlet means and an outlet to discharge engine exhaust; (b) providing a secondary air passageway means; (c) receiving ambient air in the air inlet means and providing the ambient air as primary air to the engine inlet and secondary air to the secondary air passageway means; (d) providing a mixing section having an inlet portion and an exit portion, utilizing the mixing section in directing the exhaust from the engine to primary convergent/divergent exit passageway segments, where the exhaust is discharged at supersonic velocity as primary flow components, and directing secondary air flow from the secondary air passageway means to secondary exit passageway segments which are interspersed with the primary segments and from which the secondary air is discharged at subsonic velocity as secondary flow components; and (e) providing an exhaust section to receive the primary and secondary flow components in a mixing region and causing the primary and secondary flow components to mix to create a supersonic mixed flow, the exhaust section having a variable area final nozzle through which the mixed flow is discharged.

  2. Mathematical Modelling of Bridges with SAP2000

    OpenAIRE

    Maraž, Miha

    2006-01-01

    The present work describes a relatively new programme module, which is enhanced in the recently released versions of SAP2000 software. The new module, called Bridge Modeler, is intended for simple, parametric mathematical modelling of bridges. The modelling procedure is explained on a test case through the steps of a user-friendly Bridge Wizard. For each step, we described the basic principles and the application possibilities as well as some limitations. We also explained two types of analys...

  3. A novel restricted-flow etching method for glass

    Institute of Scientific and Technical Information of China (English)

    Hai-bo XIE; Yi ZHENG; Yu-run FAN; Xin FU; Hua-yong YANG

    2009-01-01

    This paper presents a novel micro fabrication method based on the laminar characteristics of micro-scale flows. Therein the separator and etchant are alternatively arranged in micro channels to form multiple laminar streams, and the etchant is located at the site where the reaction is supposed to occur. This new micro fabrication process can be used for the high aspect ratio etching inside a microchannel on glass substrates. Furthermore, the topography of microstructure patterned by this method can be controlled by changing the flow parameters of the separator and etchant. Experiments on the effects of flow parameters on the aspect ratio, side wall profile and etching rate were carried out on a glass substrate. The effect of flow rates on the etching rate and the micro topography was analyzed, in addition, experiments with dynamical changes of the flow rate ratio of the separator and etchant showed that the verticality of the side walls of microstructures can be significantly improved. The restricted flowing etching technique not only abates the isotropic effect in the traditional wet etching but also significantly reduces the dependence on expensive photolithographic equipment.

  4. Simulating High Reynolds Number Flow by Lattice Boltzmann Method

    Institute of Scientific and Technical Information of China (English)

    KANG Xiu-Ying; LIU Da-He; ZHOU Jing; JIN Yong-Juan

    2005-01-01

    @@ A two-dimensional channel flow with different Reynolds numbers is tested by using the lattice Boltzmann method under different pressure and velocity boundary conditions. The results show that the simulation error increases,and the pressure and the flow rate become unstable under a high Reynolds number. To improve the simulation precision under a high Reynolds number, the number of fluid nodes should be enlarged. For a higher Reynoldsnumber flow, the velocity boundary with an approximately parabolic velocity profile is found to be more adaptive.Blood flow in an artery with cosine shape symmetrical narrowing is then simulated under a velocity boundary condition. Its velocity, pressure and wall shear stress distributions are consistent with previous studies.

  5. Viscous incompressible flow simulation using penalty finite element method

    Directory of Open Access Journals (Sweden)

    Sharma R.L.

    2012-04-01

    Full Text Available Numerical analysis of Navier–Stokes equations in velocity– pressure variables with traction boundary conditions for isothermal incompressible flow is presented. Specific to this study is formulation of boundary conditions on synthetic boundary characterized by traction due to friction and surface tension. The traction and open boundary conditions have been investigated in detail. Navier-Stokes equations are discretized in time using Crank-Nicolson scheme and in space using Galerkin finite element method. Pressure being unknown and is decoupled from the computations. It is determined as post processing of the velocity field. The justification to simulate this class of flow problems is presented through benchmark tests - classical lid-driven cavity flowwidely used by numerous authors due to its simple geometry and complicated flow behavior and squeezed flow between two parallel plates amenable to analytical solution. Results are presented for very low to high Reynolds numbers and compared with the benchmark results.

  6. Improved numerical methods for turbulent viscous recirculating flows

    Science.gov (United States)

    Turan, A.; Vandoormaal, J. P.

    1988-01-01

    The performance of discrete methods for the prediction of fluid flows can be enhanced by improving the convergence rate of solvers and by increasing the accuracy of the discrete representation of the equations of motion. This report evaluates the gains in solver performance that are available when various acceleration methods are applied. Various discretizations are also examined and two are recommended because of their accuracy and robustness. Insertion of the improved discretization and solver accelerator into a TEACH mode, that has been widely applied to combustor flows, illustrates the substantial gains to be achieved.

  7. An eddy viscosity calculation method for a turbulent duct flow

    Science.gov (United States)

    Antonia, R. A.; Bisset, D. K.; Kim, J.

    1991-01-01

    The mean velocity profile across a fully developed turbulent duct flow is obtained from an eddy viscosity relation combined with an empirical outer region wake function. Results are in good agreement with experiments and with direct numerical simulations in the same flow at two Reynolds numbers. In particular, the near-wall trend of the Reynolds shear stress and its variation with Reynolds number are similar to those of the simulations. The eddy viscosity method is more accurate than previous mixing length or implicit function methods.

  8. Systems and methods for rebalancing redox flow battery electrolytes

    Science.gov (United States)

    Pham, Ai Quoc; Chang, On Kok

    2015-03-17

    Various methods of rebalancing electrolytes in a redox flow battery system include various systems using a catalyzed hydrogen rebalance cell configured to minimize the risk of dissolved catalyst negatively affecting flow battery performance. Some systems described herein reduce the chance of catalyst contamination of RFB electrolytes by employing a mediator solution to eliminate direct contact between the catalyzed membrane and the RFB electrolyte. Other methods use a rebalance cell chemistry that maintains the catalyzed electrode at a potential low enough to prevent the catalyst from dissolving.

  9. Continuous-flow free acid monitoring method and system

    Science.gov (United States)

    Strain, J.E.; Ross, H.H.

    1980-01-11

    A free acid monitoring method and apparatus is provided for continuously measuring the excess acid present in a process stream. The disclosed monitoring system and method is based on the relationship of the partial pressure ratio of water and acid in equilibrium with an acid solution at constant temperature. A portion of the process stream is pumped into and flows through the monitor under the influence of gravity and back to the process stream. A continuous flowing sample is vaporized at a constant temperature and the vapor is subsequently condensed. Conductivity measurements of the condensate produces a nonlinear response function from which the free acid molarity of the sample process stream is determined.

  10. A Level Set Discontinuous Galerkin Method for Free Surface Flows

    DEFF Research Database (Denmark)

    Grooss, Jesper; Hesthaven, Jan

    2006-01-01

    We present a discontinuous Galerkin method on a fully unstructured grid for the modeling of unsteady incompressible fluid flows with free surfaces. The surface is modeled by embedding and represented by a levelset. We discuss the discretization of the flow equations and the level set equation...... as well a various ways of advancing the equations in time using velocity projection techniques. The efficacy of the method for the representation of the levelset and its reinitialization is discussed and several numerical tests confirm the robustness and versatility of the proposed scheme....

  11. Adaptive computational methods for SSME internal flow analysis

    Science.gov (United States)

    Oden, J. T.

    1986-01-01

    Adaptive finite element methods for the analysis of classes of problems in compressible and incompressible flow of interest in SSME (space shuttle main engine) analysis and design are described. The general objective of the adaptive methods is to improve and to quantify the quality of numerical solutions to the governing partial differential equations of fluid dynamics in two-dimensional cases. There are several different families of adaptive schemes that can be used to improve the quality of solutions in complex flow simulations. Among these are: (1) r-methods (node-redistribution or moving mesh methods) in which a fixed number of nodal points is allowed to migrate to points in the mesh where high error is detected; (2) h-methods, in which the mesh size h is automatically refined to reduce local error; and (3) p-methods, in which the local degree p of the finite element approximation is increased to reduce local error. Two of the three basic techniques have been studied in this project: an r-method for steady Euler equations in two dimensions and a p-method for transient, laminar, viscous incompressible flow. Numerical results are presented. A brief introduction to residual methods of a-posterior error estimation is also given and some pertinent conclusions of the study are listed.

  12. Outlier Detection Method Use for the Network Flow Anomaly Detection

    Directory of Open Access Journals (Sweden)

    Rimas Ciplinskas

    2016-06-01

    Full Text Available New and existing methods of cyber-attack detection are constantly being developed and improved because there is a great number of attacks and the demand to protect from them. In prac-tice, current methods of attack detection operates like antivirus programs, i. e. known attacks signatures are created and attacks are detected by using them. These methods have a drawback – they cannot detect new attacks. As a solution, anomaly detection methods are used. They allow to detect deviations from normal network behaviour that may show a new type of attack. This article introduces a new method that allows to detect network flow anomalies by using local outlier factor algorithm. Accom-plished research allowed to identify groups of features which showed the best results of anomaly flow detection according the highest values of precision, recall and F-measure.

  13. A reconstruction method of intra-ventricular blood flow using color flow ultrasound: a simulation study

    Science.gov (United States)

    Jang, Jaeseong; Ahn, Chi Young; Jeon, Kiwan; Choi, Jung-il; Lee, Changhoon; Seo, Jin Keun

    2015-03-01

    A reconstruction method is proposed here to quantify the distribution of blood flow velocity fields inside the left ventricle from color Doppler echocardiography measurement. From 3D incompressible Navier- Stokes equation, a 2D incompressible Navier-Stokes equation with a mass source term is derived to utilize the measurable color flow ultrasound data in a plane along with the moving boundary condition. The proposed model reflects out-of-plane blood flows on the imaging plane through the mass source term. For demonstrating a feasibility of the proposed method, we have performed numerical simulations of the forward problem and numerical analysis of the reconstruction method. First, we construct a 3D moving LV region having a specific stroke volume. To obtain synthetic intra-ventricular flows, we performed a numerical simulation of the forward problem of Navier-Stokes equation inside the 3D moving LV, computed 3D intra-ventricular velocity fields as a solution of the forward problem, projected the 3D velocity fields on the imaging plane and took the inner product of the 2D velocity fields on the imaging plane and scanline directional velocity fields for synthetic scanline directional projected velocity at each position. The proposed method utilized the 2D synthetic projected velocity data for reconstructing LV blood flow. By computing the difference between synthetic flow and reconstructed flow fields, we obtained the averaged point-wise errors of 0.06 m/s and 0.02 m/s for u- and v-components, respectively.

  14. Time-derivative preconditioning method for multicomponent flow

    Science.gov (United States)

    Housman, Jeffrey Allen

    A time-derivative preconditioned system of equations suitable for the numerical simulation of single component and multicomponent inviscid flows at all speeds is formulated. The system is shown to be hyperbolic in time and remain well-posed at low Mach numbers, allowing an efficient time marching solution strategy to be utilized from transonic to incompressible flow speeds. For multicomponent flow at low speed, a preconditioned nonconservative discretization scheme is described which preserves pressure and velocity equilibrium across fluid interfaces, handles sharp liquid/gas interfaces with large density ratios, while remaining well-conditioned for time marching methods. The method is then extended to transonic and supersonic flows using a hybrid conservative/nonconservative formulation which retains the pressure/velocity equilibrium property and converges to the correct weak solution when shocks are present. In order to apply the proposed model to complex flow applications, the overset grid methodology is used where the equations are transformed to a nonorthogonal curvilinear coordinate system and discretized on structured body-fitted curvilinear grids. The multicomponent model and its extension to homogeneous multiphase mixtures is discussed and the hyperbolicity of the governing equations is demonstrated. Low Mach number perturbation analysis is then performed on the system of equations and a local time-derivative preconditioning matrix is derived allowing time marching numerical methods to remain efficient at low speeds. Next, a particular time marching numerical method is presented along with three discretization schemes for the convective terms. These include a conservative preconditioned Roe type method, a nonconservative preconditioned Split Coefficient Matrix (SCM) method, and hybrid formulation which combines the conservative and nonconservative schemes using a simple switching function. A characteristic boundary treatment which includes time

  15. Performance assessment of the SOFA, APACHE II scoring system, and SAPS II in intensive care unit organophosphate poisoned patients.

    Science.gov (United States)

    Kim, Yong Hwan; Yeo, Jung Hoon; Kang, Mun Ju; Lee, Jun Ho; Cho, Kwang Won; Hwang, SeongYoun; Hong, Chong Kun; Lee, Young Hwan; Kim, Yang Weon

    2013-12-01

    This study assessed the ability of the Sequential Organ Failure Assessment (SOFA) and Acute Physiology, Chronic Health Evaluation (APACHE) II scoring systems, as well as the Simplified Acute Physiology Score (SAPS) II method to predict group mortality in intensive care unit (ICU) patients who were poisoned with organophosphate. The medical records of 149 organophosphate poisoned patients admitted to the ICU from September 2006 to December 2012 were retrospectively examined. The SOFA, APACHE II, and SAPS II were calculated based on initial laboratory data in the Emergency Department, and during the first 24 hr of ICU admission. The probability of death was calculated for each patient based on the SOFA score, APACHE II score, and SAPS II equations. The ability to predict group mortality by the SOFA score, APACHE II score, and SAPS II method was assessed using two by two decision matrices and receiver operating characteristic (ROC) curve analysis. A total of 131 patients (mean age, 61 yr) were enrolled. The sensitivities, specificities, and accuracies were 86.2%, 82.4%, and 83.2% for the SOFA score, respectively; 65.5%, 68.6%, and 67.9% for the APACHE II scoring system, respectively; and 86.2%, 77.5%, and 79.4% for the SAPS II, respectively. The areas under the curve in the ROC curve analysis for the SOFA score, APACHE II scoring system, and SAPS II were 0.896, 0.716, and 0.852, respectively. In conclusion, the SOFA, APACHE II, and SAPS II have different capability to discriminate and estimate early in-hospital mortality of organophosphate poisoned patients. The SOFA score is more useful in predicting mortality, and easier and simpler than the APACHE II and SAPS II.

  16. A new method for flow measurement in cryogenic systems

    Science.gov (United States)

    Grohmann, S.

    2014-03-01

    A new method for mass flow measurement of fluids in pipes is presented; its novelty lies in the capability for intrinsic calibration. The method is founded on a concept, where two independent analytic expressions for the flow rate are formed from the same direct measurement readings (input parameters). If the input parameters were error-free, the two expressions would yield identical results, by definition. This fact can be used as goal function in a minimization routine that removes systematic errors of the inherently error-prone input parameters. The uncertainty of the mass flow measurement is then only influenced by statistical effects and is typically less than 1% with regard to the measured value. The new method is explained by a proof-of-principle that is based on measurements in a large-scale cryogenic system. The intrinsic calibrations can be executed in situ at any moment during operation of a plant, and with no need for a reference standard. While the new method is applicable in any system involving single-phase fluid flow, it offers particular advantages in cryogenic application.

  17. Space-time discontinuous Galerkin method for compressible flow

    NARCIS (Netherlands)

    Klaij, C.M.

    2006-01-01

    The space-time discontinuous Galerkin method allows the simulation of compressible flow in complex aerodynamical applications requiring moving, deforming and locally refined meshes. This thesis contains the space-time discretization of the physical model, a fully explicit solver for the resulting

  18. Lattice Boltzmann method for linear oscillatory noncontinuum flows.

    Science.gov (United States)

    Shi, Yong; Yap, Ying Wan; Sader, John E

    2014-03-01

    Oscillatory gas flows are commonly generated by micro- and nanoelectromechanical systems. Due to their small size and high operating frequencies, these devices often produce noncontinuum gas flows. Theoretical analysis of such flows requires solution of the unsteady Boltzmann equation, which can present a formidable challenge. In this article, we explore the applicability of the lattice Boltzmann (LB) method to such linear oscillatory noncontinuum flows; this method is derived from the linearized Boltzmann Bhatnagar-Gross-Krook (BGK) equation. We formulate four linearized LB models in the frequency domain, based on Gaussian-Hermite quadratures of different algebraic precision (AP). The performance of each model is assessed by comparison to high-accuracy numerical solutions to the linearized Boltzmann-BGK equation for oscillatory Couette flow. The numerical results demonstrate that high even-order LB models provide superior performance over the greatest noncontinuum range. Our results also highlight intrinsic deficiencies in the current LB framework, which is incapable of capturing noncontinuum behavior at high oscillation frequencies, regardless of quadrature AP and the Knudsen number.

  19. Lattice Boltzmann method for linear oscillatory noncontinuum flows

    Science.gov (United States)

    Shi, Yong; Yap, Ying Wan; Sader, John E.

    2014-03-01

    Oscillatory gas flows are commonly generated by micro- and nanoelectromechanical systems. Due to their small size and high operating frequencies, these devices often produce noncontinuum gas flows. Theoretical analysis of such flows requires solution of the unsteady Boltzmann equation, which can present a formidable challenge. In this article, we explore the applicability of the lattice Boltzmann (LB) method to such linear oscillatory noncontinuum flows; this method is derived from the linearized Boltzmann Bhatnagar-Gross-Krook (BGK) equation. We formulate four linearized LB models in the frequency domain, based on Gaussian-Hermite quadratures of different algebraic precision (AP). The performance of each model is assessed by comparison to high-accuracy numerical solutions to the linearized Boltzmann-BGK equation for oscillatory Couette flow. The numerical results demonstrate that high even-order LB models provide superior performance over the greatest noncontinuum range. Our results also highlight intrinsic deficiencies in the current LB framework, which is incapable of capturing noncontinuum behavior at high oscillation frequencies, regardless of quadrature AP and the Knudsen number.

  20. Rain-Flow and Reverse Rain-Flow Counting Method for the Compilation of Fatigue Load Spectrum

    Institute of Scientific and Technical Information of China (English)

    宋玉普; 李朝阳; 王立成

    2001-01-01

    The rain-flow counting method is widely used to compile the fatigue load spectrum. The second stage counting of the rain-flow method is a troublesome process. In order to overcome this drawback, the rain-flow and reverse rain-flow counting method is proposed in this paper. In this counting method, the rule for counting of the rain-flow method is modified, so that the sequence of load-time need not be adjusted. This is a valid and useful method to count cycles and compile the load spectrum and it can be widely used in ocean engineering.

  1. Adaptive Spectral Estimation Methods in Color Flow Imaging.

    Science.gov (United States)

    Karabiyik, Yucel; Ekroll, Ingvild Kinn; Eik-Nes, Sturla H; Avdal, Jorgen; Lovstakken, Lasse

    2016-11-01

    Clutter rejection for color flow imaging (CFI) remains a challenge due to either a limited amount of temporal samples available or nonstationary tissue clutter. This is particularly the case for interleaved CFI and B-mode acquisitions. Low velocity blood signal is attenuated along with the clutter due to the long transition band of the available clutter filters, causing regions of biased mean velocity estimates or signal dropouts. This paper investigates how adaptive spectral estimation methods, Capon and blood iterative adaptive approach (BIAA), can be used to estimate the mean velocity in CFI without prior clutter filtering. The approach is based on confining the clutter signal in a narrow spectral region around the zero Doppler frequency while keeping the spectral side lobes below the blood signal level, allowing for the clutter signal to be removed by thresholding in the frequency domain. The proposed methods are evaluated using computer simulations, flow phantom experiments, and in vivo recordings from the common carotid and jugular vein of healthy volunteers. Capon and BIAA methods could estimate low blood velocities, which are normally attenuated by polynomial regression filters, and may potentially give better estimation of mean velocities for CFI at a higher computational cost. The Capon method decreased the bias by 81% in the transition band of the used polynomial regression filter for small packet size ( N=8 ) and low SNR (5 dB). Flow phantom and in vivo results demonstrate that the Capon method can provide color flow images and flow profiles with lower variance and bias especially in the regions close to the artery walls.

  2. Simple numerical method for predicting steady compressible flows

    Science.gov (United States)

    Vonlavante, Ernst; Nelson, N. Duane

    1986-01-01

    A numerical method for solving the isenthalpic form of the governing equations for compressible viscous and inviscid flows was developed. The method was based on the concept of flux vector splitting in its implicit form. The method was tested on several demanding inviscid and viscous configurations. Two different forms of the implicit operator were investigated. The time marching to steady state was accelerated by the implementation of the multigrid procedure. Its various forms very effectively increased the rate of convergence of the present scheme. High quality steady state results were obtained in most of the test cases; these required only short computational times due to the relative efficiency of the basic method.

  3. Characteristic particle methods for traffic flow simulations on highway networks

    CERN Document Server

    Farjoun, Yossi

    2012-01-01

    A characteristic particle method for the simulation of first order macroscopic traffic models on road networks is presented. The approach is based on the method "particleclaw", which solves scalar one dimensional hyperbolic conservations laws exactly, except for a small error right around shocks. The method is generalized to nonlinear network flows, where particle approximations on the edges are suitably coupled together at the network nodes. It is demonstrated in numerical examples that the resulting particle method can approximate traffic jams accurately, while only devoting a few degrees of freedom to each edge of the network.

  4. Traffic Flow Management Using Aggregate Flow Models and the Development of Disaggregation Methods

    Science.gov (United States)

    Sun, Dengfeng; Sridhar, Banavar; Grabbe, Shon

    2010-01-01

    A linear time-varying aggregate traffic flow model can be used to develop Traffic Flow Management (tfm) strategies based on optimization algorithms. However, there are no methods available in the literature to translate these aggregate solutions into actions involving individual aircraft. This paper describes and implements a computationally efficient disaggregation algorithm, which converts an aggregate (flow-based) solution to a flight-specific control action. Numerical results generated by the optimization method and the disaggregation algorithm are presented and illustrated by applying them to generate TFM schedules for a typical day in the U.S. National Airspace System. The results show that the disaggregation algorithm generates control actions for individual flights while keeping the air traffic behavior very close to the optimal solution.

  5. 49 CFR 40.311 - What are the requirements concerning SAP reports?

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 1 2010-10-01 2010-10-01 false What are the requirements concerning SAP reports... Process § 40.311 What are the requirements concerning SAP reports? (a) As the SAP conducting the required... ensure that you receive SAP written reports directly from the SAP performing the evaluation and that no...

  6. Role of NuSAP in Prostate Tumor Progression

    Science.gov (United States)

    2013-06-01

    of NuSAP in promoting proliferation and invasion in Prostate Cancer and identify genes that upregulate NuSAP expression. Nucleolar and spindle ...extensive bundling and stabilization of spindle microtubules against depolymerization and cross-link large numbers of microtubules into aster-like...mitotic stage observed in cells where NuSAP was knocked down compared to over expressed cells which were found similar to control. Error bars: SD

  7. TRACC: an open source software for processing sap flux data from thermal dissipation probes

    Science.gov (United States)

    Eric J. Ward; Jean-Christophe Domec; John King; Ge Sun; Steve McNulty; Asko Noormets

    2017-01-01

    Key message TRACC is an open-source software for standardizing the cleaning, conversion, and calibration of sap flux density data from thermal dissipation probes, which addresses issues of nighttime transpiration and water storage. Abstract Thermal dissipation probes (TDPs) have become a widely used method of monitoring plant water use in recent years. The use of TDPs...

  8. A review of current finite difference rotor flow methods

    Science.gov (United States)

    Caradonna, F. X.; Tung, C.

    1986-01-01

    Rotary-wing computational fluid dynamics is reaching a point where many three-dimensional, unsteady, finite-difference codes are becoming available. This paper gives a brief review of five such codes, which treat the small disturbance, conservative and nonconservative full-potential, and Euler flow models. A discussion of the methods of applying these codes to the rotor environment (including wake and trim considerations) is followed by a comparison with various available data. These data include tests of advancing lifting and nonlifting, and hovering model rotors with significant supercritical flow regions. The codes are also compared for computational efficiency.

  9. Computation of Load Flow Problems with Homotopy Methods

    Institute of Scientific and Technical Information of China (English)

    陈玉荣; 蔡大用

    2001-01-01

    Load flow computations are the basis for voltage security assessments in power systems. All of theflow equation solutions must be computed to explore the mechanisms of voltage instability and voltagecollapse. Conventional algorithms, such as Newton's methods and its variations, are not very desirablebecause they can not be easily used to find all of the solutions. This paper investigates homotopy methodswhich can be used for numerically computing the set of all isolated solutions of multivariate polynomial systemsresulting from load flow computations. The results significantly reduce the number of paths being followed.``

  10. On-line sample processing methods in flow analysis

    DEFF Research Database (Denmark)

    Miró, Manuel; Hansen, Elo Harald

    2008-01-01

    In this chapter, the state of the art of flow injection and related approaches thereof for automation and miniaturization of sample processing regardless of the aggregate state of the sample medium is overviewed. The potential of the various generation of flow injection for implementation of in......-line dilution, derivatization, separation and preconcentration methods encompassing solid reactors, solvent extraction, sorbent extraction, precipitation/coprecipitation, hydride/vapor generation and digestion/leaching protocols as hyphenated to a plethora of detection devices is discussed in detail...

  11. Using mixed methods to identify factors influencing patient flow.

    Science.gov (United States)

    Van Vaerenbergh, Cindy

    2009-11-01

    An effective method of identifying operational factors that influence patient flow can potentially lead to improvements and thus have huge benefits on the efficiency of hospital departments. This paper presents a new inductive mixed-method approach to identify operational factors that influence patient flow through an accident and emergency (A&E) department. Preliminary explorative observations were conducted, followed by semi-structured interviews with key stakeholders. A questionnaire survey of all medical, nursing, porter and clerical staff was then conducted. The observations provided factors for further exploration: skill-mix, long working hours, equipment availability, lack of orientation programmes, inefficient IT use and issues regarding communication structures. Interviewees highlighted several factors, including availability of medical supervision and senior nursing staff, nursing documentation issues, lack of morale due to overcrowding, personality differences and factors relating to the department layout. The questionnaire respondents strongly supported the importance of the previously identified factors. This paper demonstrates an effective mixed-method approach that can be replicated by other health-care managers to identify factors influencing patient flow. Further benefits include increased volume and quality of data, increased staff awareness for the influence of internal factors on patient flow and enhancing the evidence base for future decision making when prioritizing A&E projects.

  12. A multilevel adaptive projection method for unsteady incompressible flow

    Science.gov (United States)

    Howell, Louis H.

    1993-11-01

    There are two main requirements for practical simulation of unsteady flow at high Reynolds number: the algorithm must accurately propagate discontinuous flow fields without excessive artificial viscosity, and it must have some adaptive capability to concentrate computational effort where it is most needed. We satisfy the first of these requirements with a second-order Godunov method similar to those used for high-speed flows with shocks, and the second with a grid-based refinement scheme which avoids some of the drawbacks associated with unstructured meshes. These two features of our algorithm place certain constraints on the projection method used to enforce incompressibility. Velocities are cell-based, leading to a Laplacian stencil for the projection which decouples adjacent grid points. We discuss features of the multigrid and multilevel iteration schemes required for solution of the resulting decoupled problem. Variable-density flows require use of a modified projection operator--we have found a multigrid method for this modified projection that successfully handles density jumps of thousands to one. Numerical results are shown for the 2D adaptive and 3D variable-density algorithms.

  13. Intrusive Method for Uncertainty Quantification in a Multiphase Flow Solver

    Science.gov (United States)

    Turnquist, Brian; Owkes, Mark

    2016-11-01

    Uncertainty quantification (UQ) is a necessary, interesting, and often neglected aspect of fluid flow simulations. To determine the significance of uncertain initial and boundary conditions, a multiphase flow solver is being created which extends a single phase, intrusive, polynomial chaos scheme into multiphase flows. Reliably estimating the impact of input uncertainty on design criteria can help identify and minimize unwanted variability in critical areas, and has the potential to help advance knowledge in atomizing jets, jet engines, pharmaceuticals, and food processing. Use of an intrusive polynomial chaos method has been shown to significantly reduce computational cost over non-intrusive collocation methods such as Monte-Carlo. This method requires transforming the model equations into a weak form through substitution of stochastic (random) variables. Ultimately, the model deploys a stochastic Navier Stokes equation, a stochastic conservative level set approach including reinitialization, as well as stochastic normals and curvature. By implementing these approaches together in one framework, basic problems may be investigated which shed light on model expansion, uncertainty theory, and fluid flow in general. NSF Grant Number 1511325.

  14. SAP R/3 plant maintenance making it work for your business

    CERN Document Server

    Stengl, Britta

    2001-01-01

    SAP R/3 Plant Maintenance offers a clear introduction to this small but sophisticated component and provides a highly practical guide to implementing PM. Beginning with a examination of the key business processes underlying PM functionality, the book goes on to cover all the crucial aspects of maintenance planning and execution in R/3. Particular attention is given to integrating plant maintenance with a company's natural process flow.

  15. Faculty perceptions of the integration of SAP in academic programs

    Directory of Open Access Journals (Sweden)

    Sam Khoury

    2012-08-01

    Full Text Available In order to prepare students for the workforce, academic programs incorporate a variety of tools that students are likely to use in their future careers. One of these tools employed by business and technology programs is the integration of live software applications such as SAP through the SAP University Alliance (SAP UA program. Since the SAP UA program has been around for only about 10 years and the available literature on the topic is limited, research is needed to determine the strengths and weaknesses of the SAP UA program. A collaborative study of SAP UA faculty perceptions of their SAP UAs was conducted in the fall of 2011. Of the faculty invited to participate in the study, 31% completed the online survey. The results indicate that most faculty experienced difficulty implementing SAP into their programs and report that a need exists for more standardized curriculum and training, while a large percentage indicated that they are receiving the support they need from their schools and SAP.

  16. SAP 系统接口技术分析

    Institute of Scientific and Technical Information of China (English)

    盖广仓

    2012-01-01

    SAP 项目实施过程中,经常会碰到与其他系统的集成问题,在 SAP 项目范围之外,企业中还有大量的遗留系统、非 SAP 系统、外部系统,SAP 并不能满足企业所有的功能需求,需要同安全与访问控制等系统相互协作,共同来实现这些系统之间的数据交互,从而确保 SAP 投入使用后,与相关系统的接口也可用。SAP 项目实施过程中的定制操作,不会改变 SAP 系统本身,但通过 ABAP/4 开发平台则可以对 SAP 系统进行扩展,也就是通过 ABAP 开发,SAP 可以与其他 R/3 系统或者非 R/3 系统集成。

  17. Synthetic-Eddy Method for Urban Atmospheric Flow Modelling

    Science.gov (United States)

    Pavlidis, D.; Gorman, G. J.; Gomes, J. L. M. A.; Pain, C. C.; Apsimon, H.

    2010-08-01

    The computational fluid dynamics code Fluidity, with anisotropic mesh adaptivity, is used as a multi-scale obstacle-accommodating meteorological model. A novel method for generating realistic inlet boundary conditions based on the view of turbulence as a superposition of synthetic eddies is adopted. It is able to reproduce prescribed first-order and second-order one-point statistics and turbulence length scales. The aim is to simulate an urban boundary layer. The model is validated against two standard benchmark tests: a plane channel flow numerical simulation and a flow past a cube physical simulation. The performed large-eddy simulations are in good agreement with both reference models giving confidence that the model can be used to successfully simulate urban atmospheric flows.

  18. Detecting Communities by Revised Max-flow Method in Networks

    Institute of Scientific and Technical Information of China (English)

    LIU Chuan-Jian; ZHU Zhi-Qiang; WU Jian-Liang

    2013-01-01

    A ubiquitous phenomenon in networks is the presence of communities within which the network connections are dense and between which they are sparser.This paper proposes a max-flow algorithm in bipartite networks to detect communities in general networks.Firstly,we construct a bipartite network in accordance with a general network and derive a revised max-flow problem in order to uncover the community structure.Then we present a local heuristic algorithm to find the optimal solution of the revised max-flow problem.This method is applied to a variety of real-world and artificial complex networks,and the partition results confirm its effectiveness and accuracy.

  19. Double MRT thermal lattice Boltzmann method for simulating convective flows

    Energy Technology Data Exchange (ETDEWEB)

    Mezrhab, Ahmed, E-mail: mezrhab@fso.ump.m [Laboratoire de Mecanique and Energetique, Departement de Physique, Faculte des Sciences, Universite Mohammed 1er, 60000 Oujda (Morocco); Amine Moussaoui, Mohammed; Jami, Mohammed [Laboratoire de Mecanique and Energetique, Departement de Physique, Faculte des Sciences, Universite Mohammed 1er, 60000 Oujda (Morocco); Naji, Hassan [Universite Lille Nord de France, F-59000 Lille, and LML UMR CNRS 8107, F-59655 Villeneuve d' Ascq cedex (France); Bouzidi, M' hamed [Universite Clermont 2, LaMI EA 3867, IUT de Montlucon, Av. A. Briand, BP 2235, F-03101 Montlucon cedex (France)

    2010-07-26

    A two-dimensional double Multiple Relaxation Time-Thermal Lattice Boltzmann Equation (2-MRT-TLBE) method is developed for predicting convective flows in a square differentially heated cavity filled with air (Pr=0.71). In this Letter, we propose a numerical scheme to solve the flow and the temperature fields using the MRT-D2Q9 model and the MRT-D2Q5 model, respectively. Thus, the main objective of this study is to show the effectiveness of such model to predict thermodynamics for heat transfer. This model is validated by the numerical simulations of the 2-D convective square cavity flow. Excellent agreements are obtained between numerical predictions. These results demonstrate the accuracy and the effectiveness of the proposed methodology.

  20. Discrete Element Method Simulations for Complex Granular Flows

    Science.gov (United States)

    Guo, Yu; Curtis, Jennifer Sinclair

    2015-01-01

    This review article focuses on the modeling of complex granular flows employing the discrete element method (DEM) approach. The specific topic discussed is the application of DEM models for the study of the flow behavior of nonspherical, flexible, or cohesive particles, including particle breakage. The major sources of particle cohesion—liquid induced, electrostatics, van der Waals forces—and their implementation into DEM simulations are covered. These aspects of particle flow are of great importance in practical applications and hence are the significant foci of research at the forefront of current DEM modeling efforts. For example, DEM simulations of nonspherical grains can provide particle stress information needed to develop constitutive models for continuum-based simulations of large-scale industrial processes.

  1. Ground Fault Line Selection with Improved Residual Flow Incremental Method

    Directory of Open Access Journals (Sweden)

    Wenhong Li

    2013-08-01

    Full Text Available According to the shortcoming of single-phase ground fault line selection method in the resonant grounded system such as the uncertainty of its device by fast compensation with the automatic compensation equipment, an arc suppression and residual flow incremental method is proposed to effectively choose the earth fault line. Firstly, when the single-phase ground fault occurs, the arc suppression coil parameters are adjusted to realize compensation and arc suppression. Then the arc suppression coil inductance values are modulated to make the zero-sequence current of fault line changed, at the same time, the zero-sequence current value is detected and its change will be captured to select the fault line. The simulation experiments prove that the arc grounding over voltage damage can be effectively reduced by arc suppression coil full compensation and fault line can be effectively selected by arc suppression and residual flow increment method.

  2. Two Dimensional Lattice Boltzmann Method for Cavity Flow Simulation

    Directory of Open Access Journals (Sweden)

    Panjit MUSIK

    2004-01-01

    Full Text Available This paper presents a simulation of incompressible viscous flow within a two-dimensional square cavity. The objective is to develop a method originated from Lattice Gas (cellular Automata (LGA, which utilises discrete lattice as well as discrete time and can be parallelised easily. Lattice Boltzmann Method (LBM, known as discrete Lattice kinetics which provide an alternative for solving the Navier–Stokes equations and are generally used for fluid simulation, is chosen for the study. A specific two-dimensional nine-velocity square Lattice model (D2Q9 Model is used in the simulation with the velocity at the top of the cavity kept fixed. LBM is an efficient method for reproducing the dynamics of cavity flow and the results which are comparable to those of previous work.

  3. Differential localization of SAP102 and PSD-95 is revealed in hippocampal spines using super-resolution light microscopy.

    Science.gov (United States)

    Zheng, Chan-Ying; Wang, Ya-Xia; Kachar, Bechara; Petralia, Ronald S

    2011-01-01

    Synapse-associated protein 102 (SAP102) and postsynaptic density 95 (PSD-95) are two major cytoskeleton proteins in the postsynaptic density (PSD). Both of them belong to the membrane-associated guanylate kinase (MAGUK) family, which clusters and anchors glutamate receptors and other proteins at synapses. In our previous study, we found that SAP102 and PSD-95 have different distributions, using combined light/electron microscopy (LM/EM) methods.1 Here, we double labeled endogenous SAP102 and PSD-95 in mature hippocampal neurons, and then took images by two different kinds of super resolution microscopy-Stimulated Emission Depletion microscopy (STED) and DeltaVision OMX 3D super resolution microscopy. We found that our 2D and 3D super resolution data were consistent with our previous LM/EM data, showing significant differences in the localization of SAP102 and PSD-95 in spines: SAP102 is distributed in both the PSD and cytoplasm of spines, while PSD-95 is concentrated only in the PSD area. These results indicate functional differences between SAP102 and PSD-95 in synaptic organization and plasticity.

  4. Assessment of Combined Ascorbyl Palmitate (AP) and Sodium Ascorbyl Phosphate (SAP) on Facial Skin Sebum Control in Female Healthy Volunteers.

    Science.gov (United States)

    Khan, H; Akhtar, N; Ali, A

    2017-01-01

    The skin is fortified with a setup of lipophilic and hydrophilic, enzymatic and non-enzymatic antioxidant systems. Ascorbyl palmitate (AP) and sodium ascorbyl phosphate (SAP) are reported as lipophilic and hydrophilic antioxidants, respectively used for skin care. Present study was aimed to assess the combined AP (in oil phase) and SAP (in aqueous phase) via multiple emulsion (ME1) for controlling sebum secretions in healthy human females. FTIR analysis of AP and SAP was performed for identification. Multiple emulsions (ME1 and control) were prepared and analyzed for physical stability. Antioxidant activities of AP, SAP as well as ME1 (with combination of these compounds) were determined by DPPH method. 11 female volunteers were included in a single-blinded, placebo-controlled, split-face comparative study. Volunteers were instructed to apply ME1 on left cheek while control (without AP and SAP) on right cheek, for a period of 90 days. A non-invasive photometric device (Sebumeter(®)) was used for the measurement of sebum secretions on both sides of the face with subsequent time intervals. A good antioxidant activity of ME1 was observed. ME1 treatments reduced significant facial sebum secretions as compared with control/placebo treatments. It was concluded that combined AP and SAP supplementations to skin proved a promising choice for controlling facial sebum secretions and could be evaluated for undesired oily skin and acne reductions for beautifying the facial appearance. © Georg Thieme Verlag KG Stuttgart · New York.

  5. Predictive models for radial sap flux variation in coniferous, diffuse-porous and ring-porous temperate trees.

    Science.gov (United States)

    Berdanier, Aaron B; Miniat, Chelcy F; Clark, James S

    2016-08-01

    Accurately scaling sap flux observations to tree or stand levels requires accounting for variation in sap flux between wood types and by depth into the tree. However, existing models for radial variation in axial sap flux are rarely used because they are difficult to implement, there is uncertainty about their predictive ability and calibration measurements are often unavailable. Here we compare different models with a diverse sap flux data set to test the hypotheses that radial profiles differ by wood type and tree size. We show that radial variation in sap flux is dependent on wood type but independent of tree size for a range of temperate trees. The best-fitting model predicted out-of-sample sap flux observations and independent estimates of sapwood area with small errors, suggesting robustness in the new settings. We develop a method for predicting whole-tree water use with this model and include computer code for simple implementation in other studies. Published by Oxford University Press 2016. This work is written by (a) US Government employee(s) and is in the public domain in the US.

  6. Flow visualisation of downhill skiers using the lattice Boltzmann method

    Science.gov (United States)

    Asai, Takeshi; Hong, Sungchan; Ijuin, Koichi

    2017-03-01

    In downhill alpine skiing, skiers often exceed speeds of 120 km h-1, with air resistance substantially affecting the overall race times. To date, studies on air resistance in alpine skiing have used wind tunnels and actual skiers to examine the relationship between the gliding posture and magnitude of drag and for the design of skiing equipment. However, these studies have not revealed the flow velocity distribution and vortex structure around the skier. In the present study, computational fluid dynamics are employed with the lattice Boltzmann method to derive the relationship between total drag and the flow velocity around a downhill skier in the full-tuck position. Furthermore, the flow around the downhill skier is visualised, and its vortex structure is examined. The results show that the total drag force in the downhill skier model is 27.0 N at a flow velocity of 15 m s-1, increasing to 185.8 N at 40 m s-1. From analysis of the drag distribution and the flow profile, the head, upper arms, lower legs, and thighs (including buttocks) are identified as the major sources of drag on a downhill skier. Based on these results, the design of suits and equipment for reducing the drag from each location should be the focus of research and development in ski equipment. This paper describes a pilot study that introduces undergraduate students of physics or engineering into this research field. The results of this study are easy to understand for undergraduate students.

  7. Review of Upscaling Methods for Describing Unsaturated Flow

    Energy Technology Data Exchange (ETDEWEB)

    BD Wood

    2000-09-26

    The representation of small-scale features can be a challenge when attempting to model unsaturated flow in large domains. Upscaling methods offer the possibility of reducing the amount of resolution required to adequately simulate such a problem. In this report, the various upscaling techniques that are discussed in the literature are reviewed. The following upscaling methods have been identified from the literature: (1) stochastic methods, (2) renormalization methods, and (3) volume averaging and homogenization methods; in addition, a final technique, full resolution numerical modeling, is also discussed. Each of these techniques has its advantages and disadvantages. The trade-off is a reduction in accuracy in favor of a method that is easier to employ. For practical applications, the most reasonable approach appears to be one in which any of the upscaling methods identified above maybe suitable for upscaling in regions where the variations in the parameter fields are small. For regions where the subsurface structure is more complex, only the homogenization and volume averaging methods are probably suitable. With the continual increases in computational capacity, fill-resolution numerical modeling may in many instances provide a tractable means of solving the flow problem in unsaturated systems.

  8. Totally Coded Method for Signal Flow Graph Algorithm

    Institute of Scientific and Technical Information of China (English)

    XU Jing-bo; ZHOU Mei-hua

    2002-01-01

    After a code-table has been established by means of node association information from signal flow graph, the totally coded method (TCM) is applied merely in the domain of code operation beyond any figure-earching algorithm. The code-series (CS) have the holoinformation nature, so that both the content and the sign of each gain- term can be determined via the coded method. The principle of this method is simple and it is suited for computer programming. The capability of the computer-aided analysis for switched current network(SIN) can be enhanced.

  9. A fictitious domain method for particulate flows with heat transfer

    Science.gov (United States)

    Yu, Zhaosheng; Shao, Xueming; Wachs, Anthony

    2006-09-01

    The distributed-Lagrange-multiplier/fictitious-domain (DLM/FD) method of Glowinski et al. [R. Glowinski, T.-W. Pan, T.I. Hesla, D.D. Joseph, A distributed Lagrange multiplier/fictitious domain method for particulate flows, Int. J. Multiphase Flow 25 (1999) 755-794] is extended to deal with heat transfer in particulate flows in two dimensions. The Boussinesq approximation is employed for the coupling between the flow and temperature fields. The fluid-flow equations are solved with the finite-difference projection method on a half-staggered grid. In our operator splitting scheme, the Lagrange multipliers at the previous time level are kept in the fluid equations, and the new Lagrange multipliers for the rigid-body motion constraint and the Dirichlet temperature boundary condition are determined from the reduced saddle-point problem, whereas a very simple scheme based on the fully explicit computation of the Lagrange multiplier is proposed for the problem in which the solid heat conduction inside the particle boundary is also considered. Our code for the case of fixed temperature on the immersed boundary is verified by comparing favorably our results on the natural convection driven by a hot cylinder eccentrically placed in a square box and on the sedimentation of a cold circular particle in a vertical channel to the data in the literature. The code for the case of freely varying temperature on the boundaries of freely moving particles is applied to analyze the motion of a catalyst particle in a box and in particular the heat conductivities of nanofluids and sheared non-colloidal suspensions, respectively. Our preliminary computational results support the argument that the micro-heat-convection in the fluids is primarily responsible for the unusually high heat conductivity of nanofluids. It is shown that the Peclet number plays a negative role in the diffusion-related heat conductivity of a sheared non-colloidal suspension, whereas the Reynolds number does the

  10. Development of a Wind Turbine Rotor Flow Panel Method

    Energy Technology Data Exchange (ETDEWEB)

    Van Garrel, A. [ECN Wind Energy, Petten (Netherlands)

    2011-12-15

    The ongoing trend towards larger wind turbines intensifies the demand for more physically realistic wind turbine rotor aerodynamics models that can predict the detailed transient pressure loadings on the rotor blades better than current engineering models. In this report the mathematical, numerical, and practical aspects of a new wind turbine rotor flow simulation code is described. This wind turbine simulation code is designated ROTORFLOW. In this method the fluid dynamics problem is solved through a boundary integral equation which reduces the problem to the surface of the configuration. The derivation of the integral equations is described as well as the assumptions made to arrive at them starting with the full Navier-Stokes equations. The basic numerical aspects in the solution method are described and a verification study is performed to confirm the validity of the implementation. Example simulations with the code show the flow solutions for a stationary wing and for a rotating wing in yawed conditions. With the ROTORFLOW code developed in this project it is possible to simulate the unsteady flow around wind turbine rotors in yawed conditions and obtain detailed pressure distributions, and thus blade loadings, at the surface of the blades. General rotor blade geometries can be handled, opening the way to the detailed flow analysis of winglets, partial span flaps, swept blade tips, etc. The ROTORFLOW solver only requires a description of the rotor surface which keeps simulation preparation time short, and makes it feasible to use the solver in the design iteration process.

  11. The curvHDR method for gating flow cytometry samples

    Directory of Open Access Journals (Sweden)

    Wand Matthew P

    2010-01-01

    Full Text Available Abstract Background High-throughput flow cytometry experiments produce hundreds of large multivariate samples of cellular characteristics. These samples require specialized processing to obtain clinically meaningful measurements. A major component of this processing is a form of cell subsetting known as gating. Manual gating is time-consuming and subjective. Good automatic and semi-automatic gating algorithms are very beneficial to high-throughput flow cytometry. Results We develop a statistical procedure, named curvHDR, for automatic and semi-automatic gating. The method combines the notions of significant high negative curvature regions and highest density regions and has the ability to adapt well to human-perceived gates. The underlying principles apply to dimension of arbitrary size, although we focus on dimensions up to three. Accompanying software, compatible with contemporary flow cytometry infor-matics, is developed. Conclusion The method is seen to adapt well to nuances in the data and, to a reasonable extent, match human perception of useful gates. It offers big savings in human labour when processing high-throughput flow cytometry data whilst retaining a good degree of efficacy.

  12. The New Performance Calculation Method of Fouled Axial Flow Compressor

    Directory of Open Access Journals (Sweden)

    Huadong Yang

    2014-01-01

    Full Text Available Fouling is the most important performance degradation factor, so it is necessary to accurately predict the effect of fouling on engine performance. In the previous research, it is very difficult to accurately model the fouled axial flow compressor. This paper develops a new performance calculation method of fouled multistage axial flow compressor based on experiment result and operating data. For multistage compressor, the whole compressor is decomposed into two sections. The first section includes the first 50% stages which reflect the fouling level, and the second section includes the last 50% stages which are viewed as the clean stage because of less deposits. In this model, the performance of the first section is obtained by combining scaling law method and linear progression model with traditional stage stacking method; simultaneously ambient conditions and engine configurations are considered. On the other hand, the performance of the second section is calculated by averaged infinitesimal stage method which is based on Reynolds’ law of similarity. Finally, the model is successfully applied to predict the 8-stage axial flow compressor and 16-stage LM2500-30 compressor. The change of thermodynamic parameters such as pressure ratio, efficiency with the operating time, and stage number is analyzed in detail.

  13. The new performance calculation method of fouled axial flow compressor.

    Science.gov (United States)

    Yang, Huadong; Xu, Hong

    2014-01-01

    Fouling is the most important performance degradation factor, so it is necessary to accurately predict the effect of fouling on engine performance. In the previous research, it is very difficult to accurately model the fouled axial flow compressor. This paper develops a new performance calculation method of fouled multistage axial flow compressor based on experiment result and operating data. For multistage compressor, the whole compressor is decomposed into two sections. The first section includes the first 50% stages which reflect the fouling level, and the second section includes the last 50% stages which are viewed as the clean stage because of less deposits. In this model, the performance of the first section is obtained by combining scaling law method and linear progression model with traditional stage stacking method; simultaneously ambient conditions and engine configurations are considered. On the other hand, the performance of the second section is calculated by averaged infinitesimal stage method which is based on Reynolds' law of similarity. Finally, the model is successfully applied to predict the 8-stage axial flow compressor and 16-stage LM2500-30 compressor. The change of thermodynamic parameters such as pressure ratio, efficiency with the operating time, and stage number is analyzed in detail.

  14. An efficient method for enumerating oral spirochetes using flow cytometry.

    Science.gov (United States)

    Orth, Rebecca; O'Brien-Simpson, Neil; Dashper, Stuart; Walsh, Katrina; Reynolds, Eric

    2010-02-01

    Spirochetes, such as Treponema denticola, are thin walled, helical, motile bacteria. They are notoriously difficult to enumerate due to their thinness and the difficulties associated with culturing them. Here we have developed a modified oral bacterial growth medium (OBGM) that significantly improves the cultivation of T. denticola compared with a previously published growth medium. Three methods for the enumeration of T. denticola, semi-solid growth medium colony-forming unit (CFU) counts, DNA analysis and flow cytometry, are described and compared. Enumeration of T. denticola using the semi-solid agar method resulted in a positive linear relationship with absorbance of the culture (R(2)=0.9423). However, the semi-solid agar method was found to consistently underestimate (by 50 fold) the T. denticola cell density compared to previously published data. DNA analysis of T. denticola cultures reliably and consistently resulted in a positive linear relationship with absorbance (R(2)=0.9360), giving a calculated cell density of 6.9 x 10(8)cells/mL at an absorbance of 0.2 at 650 nm. Flow cytometry was also found to result in a positive linear relationship with absorbance (R(2)=0.9874), giving a calculated cell density of 6.6 x 10(8)cells/mL at an absorbance of 0.2 at 650 nm. In comparing all of these enumeration methods, the flow cytometry method was found to have distinct advantages, as it is accurate, rapid, and could distinguish between live and dead bacteria. Thus flow cytometry is a recommended means for the rapid and reliable enumeration of viable spirochetes from culture.

  15. Analytical methods for heat transfer and fluid flow problems

    CERN Document Server

    Weigand, Bernhard

    2015-01-01

    This book describes useful analytical methods by applying them to real-world problems rather than solving the usual over-simplified classroom problems. The book demonstrates the applicability of analytical methods even for complex problems and guides the reader to a more intuitive understanding of approaches and solutions. Although the solution of Partial Differential Equations by numerical methods is the standard practice in industries, analytical methods are still important for the critical assessment of results derived from advanced computer simulations and the improvement of the underlying numerical techniques. Literature devoted to analytical methods, however, often focuses on theoretical and mathematical aspects and is therefore useless to most engineers. Analytical Methods for Heat Transfer and Fluid Flow Problems addresses engineers and engineering students. The second edition has been updated, the chapters on non-linear problems and on axial heat conduction problems were extended. And worked out exam...

  16. Axial flow heat exchanger devices and methods for heat transfer using axial flow devices

    Energy Technology Data Exchange (ETDEWEB)

    Koplow, Jeffrey P.

    2016-02-16

    Systems and methods described herein are directed to rotary heat exchangers configured to transfer heat to a heat transfer medium flowing in substantially axial direction within the heat exchangers. Exemplary heat exchangers include a heat conducting structure which is configured to be in thermal contact with a thermal load or a thermal sink, and a heat transfer structure rotatably coupled to the heat conducting structure to form a gap region between the heat conducting structure and the heat transfer structure, the heat transfer structure being configured to rotate during operation of the device. In example devices heat may be transferred across the gap region from a heated axial flow of the heat transfer medium to a cool stationary heat conducting structure, or from a heated stationary conducting structure to a cool axial flow of the heat transfer medium.

  17. 49 CFR 40.295 - May employees or employers seek a second SAP evaluation if they disagree with the first SAP's...

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 1 2010-10-01 2010-10-01 false May employees or employers seek a second SAP evaluation if they disagree with the first SAP's recommendations? 40.295 Section 40.295 Transportation Office... seek a second SAP evaluation if they disagree with the first SAP's recommendations? (a) As an employee...

  18. Analysis of Axial Flow Ventilation Fans by Vortex - Method.

    Science.gov (United States)

    Hardin, Richard Anthony

    A steady vortex-lattice method is used to solve the lifting surface equation for an axial flow fan. The type of fan studied is designed for industrial and ventilation applications and in thermofluid systems such as cooling towers. The fan blades are thin cambered surfaces manufactured from metal sheets. The numerical approach is inviscid and results in a boundary value problem with viscous effects partially accounted for by application of drag coefficient data. A non-linear wake alignment procedure is used to account for the effects of vorticity shedding in the wake and variation in wake geometry with operating conditions. The wake alignment procedure is semi-free with wake input parameters required for accurate use of the technique. A study of the wake parameters was conducted and gave trends in the variation of their values with flow rate. At "free-air" conditions, flow visualization estimates of these parameters were found to agree with those from the computations. Comparisons are made between the measured and predicted fan performance with and without a surrounding duct. The comparison of the results were especially good at the "free-air" condition using wake parameters determined from flow visualization and an inlet velocity profile measured using hot-wire anemometry. To enable better understanding of basic flow phenomena and to provide data for verification of numerical analyses, a method for measuring unsteady surface pressure on a rotating axial-flow fan blade was devised. Unsteadiness of pressure on the blade surfaces is due to the effects of upstream fan motor supports and other installation features. A pressure transducer and signal amplification circuit were mounted on a circuit board at the rotating hub with signals taken off the rotating shaft through copper disk-mercury slip rings. The pressure difference across the blade was determined and the data were corrected for time lag and distortion caused by the length of tubing. The pressure difference

  19. SAP deficiency mitigated atherosclerotic lesions in ApoE(-/-) mice.

    Science.gov (United States)

    Zheng, Lingyun; Wu, Teng; Zeng, Cuiling; Li, Xiangli; Li, Xiaoqiang; Wen, Dingwen; Ji, Tianxing; Lan, Tian; Xing, Liying; Li, Jiangchao; He, Xiaodong; Wang, Lijing

    2016-01-01

    Serum amyloid P conpoent (SAP), a member of the pentraxin family, interact with pathogens and cell debris to promote their removal by macrophages and neutrophils and is co-localized with atherosclerotic plaques in patients. However, the exact mechanism of SAP in atherogenesis is still unclear. We investigated whether SAP influence macrophage recruitment and foam cell formation and ultimately affect atherosclerotic progression. we generated apoE(-/-); SAP(-/-) (DKO) mice and fed them western diet for 4 and 8 weeks to characterize atherosclerosis development. SAP deficiency effectively reduced plaque size both in the aorta (p = 0.0006 for 4 wks; p = 0.0001 for 8 wks) and the aortic root (p = 0.0061 for 4 wks; p = 0.0079 for 8wks) compared with apoE(-/-) mice. Meanwhile, SAP deficiency inhibited oxLDL-induced foam cell formation (p = 0.0004) compared with apoE(-/-) mice and SAP treatment increases oxLDL-induced foam cell formation (p = 0.002) in RAW cells. Besides, SAP deficiency reduced macrophages recruitment (p = 0.035) in vivo and in vitro (p = 0.026). Furthermore, SAP treatment enhanced CD36 (p = 0.007) and FcγRI (p = 0.031) expression induced by oxLDL through upregulating JNK and p38 MAPK phosphorylation whereas specific JNK1/2 inhibitor reduced CD36 (p = 0.0005) and FcγRI (P = 0.0007) expression in RAW cell. SAP deficiency also significantly decreased the expression of M1 and M2 macrophage markers and inflammatory cytokines in oxLDL-induced macrophages. SAP deficiency mitigated foam cell formation and atherosclerotic development in apoE(-/-) mice, due to reduction in macrophages recruitment, polarization and pro-inflammatory cytokines and inhibition the CD36/FcγR-dependent signaling pathway. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  20. Aerosol flow reactor method for synthesis of drug nanoparticles.

    Science.gov (United States)

    Eerikäinen, Hannele; Watanabe, Wiwik; Kauppinen, Esko I; Ahonen, P Petri

    2003-05-01

    An aerosol flow reactor method, a one-step continuous process to produce nanometer-sized drug particles with unimodal size distribution, was developed. This method involves first dissolving the drug material in question into a suitable solvent, which is then followed by atomising the solution as fine droplets into carrier gas. A heated laminar flow reactor tube is used to evaporate the solvent, and solid drug nanoparticles are formed. In this study, the effect of drying temperature on the particle size and morphology was examined. A glucocorticosteroid used for asthma therapy, beclomethasone dipropionate, was selected as an experimental model drug. The geometric number mean particle diameter increases significantly with increasing reactor temperatures due to formation of hollow nanoparticles. Above 160 degrees C, however, further increase in temperature results in decreasing particle size. The produced nanoparticles are spherical and show smooth surfaces at all studied experimental conditions.

  1. Selection of the best consultant for SAP ERP project using combined AHP-IBA approach

    Directory of Open Access Journals (Sweden)

    Martinović Nataša

    2014-01-01

    Full Text Available In this paper we propose a combined AHP-IBA model for selecting the best SAP consultant for an SAP ERP project. The goal of the SAP Project Manager is to choose the best consultant, the one who is able to implement standard SAP functionalities with quality and on time. When making a decision on the basis of multiple criteria, the traditional Analytic Hierarchy Process (AHP method does not take into account the fact that attributes may correlate, assuming that there are no dependencies between them. However, the dependencies of the attributes can often be used to model important knowledge for multiple criteria decision analysis. We propose an extension to the traditional AHP method by applying Interpolative realization of Boolean algebra (IBA, using AHP to determine the criteria weights, and IBA to model the logical interactions among criteria. The research conducted on ERP consultant selection suggests that the decision making process is modelled more accurately if logical interactions between attributes are modelled before applying AHP.

  2. Research on stochastic power-flow study methods. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Heydt, G. T. [ed.

    1981-01-01

    A general algorithm to determine the effects of uncertainty in bus load and generation on the output of conventional power flow analysis is presented. The use of statistical moments is presented and developed as a means for representing the stochastic process. Statistical moments are used to describe the uncertainties, and facilitate the calculations of single and multivarlate probability density functions of input and output variables. The transformation of the uncertainty through the power flow equations is made by the expansion of the node equations in a multivariate Taylor series about an expected operating point. The series is truncated after the second order terms. Since the power flow equations are nonlinear, the expected values of output quantities is in general not the solution to the conventional load flow problem using expected values of input quantities. The second order transformation offers a correction vector and allows the consideration of larger uncertainties which have caused significant error in the current linear transformation algorithms. Voltage controlled busses are included with consideration of upper and lower limits. The finite reactive power available at generation sites, and fixed ranges of transformer tap movement may have a significant effect on voltage and line power flow statistics. A method is given which considers limitation constraints in the evaluation of all output quantities. The bus voltages, line power flows, transformer taps, and generator reactive power requirements are described by their statistical moments. Their values are expressed in terms of the probability that they are above or below specified limits, and their expected values given that they do fall outside the limits. Thus the algorithm supplies information about severity of overload as well as probability of occurrence. An example is given for an eleven bus system, evaluating each quantity separately. The results are compared with Monte Carlo simulation.

  3. A Simple Method of FLow Field DIagnosis in Multistage Axial Flow Compressors

    Institute of Scientific and Technical Information of China (English)

    JieLiu; DajunYe

    1994-01-01

    The calculating method of flow field diagnosis in multistage axial compressors is presented in this paper.The distributions of loss and deviation angle of every blade row,and blockage factors are evalusted using tested total temperature and total pressure at inlet and outlet of compressor,as well as the endwall static pressures.One operating Mode of a two-stage fan is presented comparing results from the diagnostic method with measurements,and the results have demonstrated the important effects of diagnostic method.

  4. Lagrangian transported MDF methods for compressible high speed flows

    Science.gov (United States)

    Gerlinger, Peter

    2017-06-01

    This paper deals with the application of thermochemical Lagrangian MDF (mass density function) methods for compressible sub- and supersonic RANS (Reynolds Averaged Navier-Stokes) simulations. A new approach to treat molecular transport is presented. This technique on the one hand ensures numerical stability of the particle solver in laminar regions of the flow field (e.g. in the viscous sublayer) and on the other hand takes differential diffusion into account. It is shown in a detailed analysis, that the new method correctly predicts first and second-order moments on the basis of conventional modeling approaches. Moreover, a number of challenges for MDF particle methods in high speed flows is discussed, e.g. high cell aspect ratio grids close to solid walls, wall heat transfer, shock resolution, and problems from statistical noise which may cause artificial shock systems in supersonic flows. A Mach 2 supersonic mixing channel with multiple shock reflection and a model rocket combustor simulation demonstrate the eligibility of this technique to practical applications. Both test cases are simulated successfully for the first time with a hybrid finite-volume (FV)/Lagrangian particle solver (PS).

  5. Path planning in uncertain flow fields using ensemble method

    Science.gov (United States)

    Wang, Tong; Le Maître, Olivier P.; Hoteit, Ibrahim; Knio, Omar M.

    2016-10-01

    An ensemble-based approach is developed to conduct optimal path planning in unsteady ocean currents under uncertainty. We focus our attention on two-dimensional steady and unsteady uncertain flows, and adopt a sampling methodology that is well suited to operational forecasts, where an ensemble of deterministic predictions is used to model and quantify uncertainty. In an operational setting, much about dynamics, topography, and forcing of the ocean environment is uncertain. To address this uncertainty, the flow field is parametrized using a finite number of independent canonical random variables with known densities, and the ensemble is generated by sampling these variables. For each of the resulting realizations of the uncertain current field, we predict the path that minimizes the travel time by solving a boundary value problem (BVP), based on the Pontryagin maximum principle. A family of backward-in-time trajectories starting at the end position is used to generate suitable initial values for the BVP solver. This allows us to examine and analyze the performance of the sampling strategy and to develop insight into extensions dealing with general circulation ocean models. In particular, the ensemble method enables us to perform a statistical analysis of travel times and consequently develop a path planning approach that accounts for these statistics. The proposed methodology is tested for a number of scenarios. We first validate our algorithms by reproducing simple canonical solutions, and then demonstrate our approach in more complex flow fields, including idealized, steady and unsteady double-gyre flows.

  6. Path planning in uncertain flow fields using ensemble method

    KAUST Repository

    Wang, Tong

    2016-08-20

    An ensemble-based approach is developed to conduct optimal path planning in unsteady ocean currents under uncertainty. We focus our attention on two-dimensional steady and unsteady uncertain flows, and adopt a sampling methodology that is well suited to operational forecasts, where an ensemble of deterministic predictions is used to model and quantify uncertainty. In an operational setting, much about dynamics, topography, and forcing of the ocean environment is uncertain. To address this uncertainty, the flow field is parametrized using a finite number of independent canonical random variables with known densities, and the ensemble is generated by sampling these variables. For each of the resulting realizations of the uncertain current field, we predict the path that minimizes the travel time by solving a boundary value problem (BVP), based on the Pontryagin maximum principle. A family of backward-in-time trajectories starting at the end position is used to generate suitable initial values for the BVP solver. This allows us to examine and analyze the performance of the sampling strategy and to develop insight into extensions dealing with general circulation ocean models. In particular, the ensemble method enables us to perform a statistical analysis of travel times and consequently develop a path planning approach that accounts for these statistics. The proposed methodology is tested for a number of scenarios. We first validate our algorithms by reproducing simple canonical solutions, and then demonstrate our approach in more complex flow fields, including idealized, steady and unsteady double-gyre flows.

  7. Design of Poiseuille Flow Controllers Using the Method of Inequalities

    Institute of Scientific and Technical Information of China (English)

    John McKernan; James F.Whidborne; George Papadakis

    2009-01-01

    This paper investigates the use of the method of inequalities (MoI) to design output-feedback compensators for the problem of the control of instabilities in a laminar plane Poiseuille flow.In common with many flows,the dynamics of streamwise vortices in plane Poiseuille flow are very non-normal.Consequently,small perturbations grow rapidly with a large transient that may trigger nonlinearities and lead to turbulence even though such perturbations would,in a linear flow model,eventually decay.Such a system can be described as a conditionally linear system.The sensitivity is measured using the maximum transient energy growth,which is widely used in the fluid dynamics community.The paper considers two approaches.In the first approach,the MoI is used to design low-order proportional and proportional-integral (PI) controllers.In the second one,the MoI is combined with McFarlane and Glover's H∞ loop-shaping design procedure in a mixed-optimization approach.

  8. Path planning in uncertain flow fields using ensemble method

    Science.gov (United States)

    Wang, Tong; Le Maître, Olivier P.; Hoteit, Ibrahim; Knio, Omar M.

    2016-08-01

    An ensemble-based approach is developed to conduct optimal path planning in unsteady ocean currents under uncertainty. We focus our attention on two-dimensional steady and unsteady uncertain flows, and adopt a sampling methodology that is well suited to operational forecasts, where an ensemble of deterministic predictions is used to model and quantify uncertainty. In an operational setting, much about dynamics, topography, and forcing of the ocean environment is uncertain. To address this uncertainty, the flow field is parametrized using a finite number of independent canonical random variables with known densities, and the ensemble is generated by sampling these variables. For each of the resulting realizations of the uncertain current field, we predict the path that minimizes the travel time by solving a boundary value problem (BVP), based on the Pontryagin maximum principle. A family of backward-in-time trajectories starting at the end position is used to generate suitable initial values for the BVP solver. This allows us to examine and analyze the performance of the sampling strategy and to develop insight into extensions dealing with general circulation ocean models. In particular, the ensemble method enables us to perform a statistical analysis of travel times and consequently develop a path planning approach that accounts for these statistics. The proposed methodology is tested for a number of scenarios. We first validate our algorithms by reproducing simple canonical solutions, and then demonstrate our approach in more complex flow fields, including idealized, steady and unsteady double-gyre flows.

  9. Computation of a turbulent channel flow using PDF method

    Energy Technology Data Exchange (ETDEWEB)

    Minier, J.P. [Electricite de France (EDF), 78 - Chatou (France). Lab. National d`Hydraulique; Pozorski, J. [Polish Academy of Sciences, Gdansk (Poland). Inst. of Fluid-Flow Machinery

    1997-05-01

    The purpose of the present paper is to present an analysis of a PDF model (Probability Density Function) and an illustration of the possibilities offered by such a method for a high-Reynolds turbulent channel flow. The first part presents the principles of the PDF approach and the introduction of stochastic processes along with a Lagrangian point of view. The model retained is the one put forward by Pope (1991) and includes evolution equations for location, velocity and dissipation of a large number of particles. Wall boundary conditions are then developed for particles. These conditions allow statistical results of the logarithmic region to be correctly reproduced. Simulation of non-homogeneous flows require a pressure-gradient algorithm which is briefly described. Developments are validated by analysing numerical predictions with respect to Comte Bellot experimental data (1965) on a channel flow. This example illustrates the ability of the approach to simulate wall-bounded flows and to provide detailed information such as skewness and flatness factors. (author) 9 refs.

  10. Structural and binding studies of SAP-1 protein with heparin.

    Science.gov (United States)

    Yadav, Vikash K; Mandal, Rahul S; Puniya, Bhanwar L; Kumar, Rahul; Dey, Sharmistha; Singh, Sarman; Yadav, Savita

    2015-03-01

    SAP-1 is a low molecular weight cysteine protease inhibitor (CPI) which belongs to type-2 cystatins family. SAP-1 protein purified from human seminal plasma (HuSP) has been shown to inhibit cysteine and serine proteases and exhibit interesting biological properties, including high temperature and pH stability. Heparin is a naturally occurring glycosaminoglycan (with varied chain length) which interacts with a number of proteins and regulates multiple steps in different biological processes. As an anticoagulant, heparin enhances inhibition of thrombin by the serpin antithrombin III. Therefore, we have employed surface plasmon resonance (SPR) to improve our understanding of the binding interaction between heparin and SAP-1 (protease inhibitor). SPR data suggest that SAP-1 binds to heparin with a significant affinity (KD = 158 nm). SPR solution competition studies using heparin oligosaccharides showed that the binding of SAP-1 to heparin is dependent on chain length. Large oligosaccharides show strong binding affinity for SAP-1. Further to get insight into the structural aspect of interactions between SAP-1 and heparin, we used modelled structure of the SAP-1 and docked with heparin and heparin-derived polysaccharides. The results suggest that a positively charged residue lysine plays important role in these interactions. Such information should improve our understanding of how heparin, present in the reproductive tract, regulates cystatins activity. © 2014 John Wiley & Sons A/S.

  11. Numerical Method for Darcy Flow Derived Using Discrete Exterior Calculus

    Science.gov (United States)

    Hirani, A. N.; Nakshatrala, K. B.; Chaudhry, J. H.

    2015-05-01

    We derive a numerical method for Darcy flow, and also for Poisson's equation in mixed (first order) form, based on discrete exterior calculus (DEC). Exterior calculus is a generalization of vector calculus to smooth manifolds and DEC is one of its discretizations on simplicial complexes such as triangle and tetrahedral meshes. DEC is a coordinate invariant discretization, in that it does not depend on the embedding of the simplices or the whole mesh. We start by rewriting the governing equations of Darcy flow using the language of exterior calculus. This yields a formulation in terms of flux differential form and pressure. The numerical method is then derived by using the framework provided by DEC for discretizing differential forms and operators that act on forms. We also develop a discretization for a spatially dependent Hodge star that varies with the permeability of the medium. This also allows us to address discontinuous permeability. The matrix representation for our discrete non-homogeneous Hodge star is diagonal, with positive diagonal entries. The resulting linear system of equations for flux and pressure are saddle type, with a diagonal matrix as the top left block. The performance of the proposed numerical method is illustrated on many standard test problems. These include patch tests in two and three dimensions, comparison with analytically known solutions in two dimensions, layered medium with alternating permeability values, and a test with a change in permeability along the flow direction. We also show numerical evidence of convergence of the flux and the pressure. A convergence experiment is included for Darcy flow on a surface. A short introduction to the relevant parts of smooth and discrete exterior calculus is included in this article. We also include a discussion of the boundary condition in terms of exterior calculus.

  12. The Application System Integration Based on Middleware SAP Business Connector%基于中间件平台SAP Business Connector的应用系统集成

    Institute of Scientific and Technical Information of China (English)

    佘春子

    2007-01-01

    文中介绍SAP BC(SAP Business Connector)基本概念和其最新技术SAP XI(SAP Exchange Infrastructure),其次概述SAP BC技术架构,最后提出基于SAPBC平台的应用系统集成方案:基于该方案并实现了E-comlIlerce-采购交互商务系统.

  13. Effects of forest environment factors on dynamic of sap flow in Camellia oleifera tree at spring shoot growing stage%林地环境因子对油茶春梢生长期液流动态的影响

    Institute of Scientific and Technical Information of China (English)

    陈志钢; 苏淑钗; 周寅杰; 李超

    2013-01-01

    In order to research dynamic of sap flow velocity (SFV) in Camellia oleifera tree at spring shoot growing stage,SFV and environmental factors in the field were measured by sap flow measurement technique with thermal diffusion probe and micro-meteorological station from March to May.The results indicate that,daily mean temperature sharply increases to 27.5 ℃ from 7.5 ℃,and water in soil is sufficient in spring shoot growing stage.SFV fluctuates frequently with environmental factors changing,and weather order based on SFV from high to low is sunny day,cloudy day,overcast sky,rain day.The results of correlation analysis and stepwise regression analysis indicate that solar radiation,photosynthetic active radiation and temperature have significant correlation with SFV,but air humidity has a significant correlation with it.With weather change from sunny day,cloudy day,to overcast sky,the correlation coefficient of SFV is decreased with radiation,but it is increased with temperature,and it is no obvious change with wind velocity and soil moisture.The regression models between SFV in different weather conditions and environmental factors were established.The model is up to significant level,and determination coefficients are over 0.93 except rain day.%为了研究油茶春梢生长期液流的动态变化规律,利用植物径流仪及自动气象记录仪,对盛果期油茶春梢生长期(3月~5月)的液流动态及林地环境因子进行了连续监测,研究结果表明:在春梢生长期林地土壤的水分充足,日平均气温由7.5℃大幅上升至27.5℃;春梢生长期油茶液流随环境因子变化的波动较大,不同天气的液流大小为晴天>多云>阴天>雨天.液流与环境因子的相关分析及逐步回归分析结果表明,总辐射、光合有效辐射、气温对液流的相关系数极高,空气相对湿度与液流有较高的负相关;随着天气由晴天到多云再到阴天的变化,液流与辐射的相关系数降

  14. Critical Care Nurses Inadequately Assess SAPS II Scores of Very Ill Patients in Real Life

    Directory of Open Access Journals (Sweden)

    Andreas Perren

    2012-01-01

    Full Text Available Background. Reliable ICU severity scores have been achieved by various healthcare workers but nothing is known regarding the accuracy in real life of severity scores registered by untrained nurses. Methods. In this retrospective multicentre audit, three reviewers independently reassessed 120 SAPS II scores. Correlation and agreement of the sum-scores/variables among reviewers and between nurses and the reviewers’ gold standard were assessed globally and for tertiles. Bland and Altman (gold standard—nurses of sum scores and regression of the difference were determined. A logistic regression model identifying risk factors for erroneous assessments was calculated. Results. Correlation for sum scores among reviewers was almost perfect (mean ICC = 0.985. The mean (±SD nurse-registered SAPS II sum score was 40.3±20.2 versus 44.2±24.9 of the gold standard (32 points scores. The lowest agreement was found in high SAPS II tertiles for haemodynamics (k = 0.45–0.51. Conclusions. In real life, nurse-registered SAPS II scores of very ill patients are inaccurate. Accuracy of scores was not associated with nurses’ characteristics.

  15. Assessing the ERP-SAP implementation strategy from cultural perspectives

    Science.gov (United States)

    Wang, Gunawan; Syaiful, Bakhri; Sfenrianto; Nurul, Fajar Ahmad

    2017-09-01

    Implementing ERP-SAP projects in Indonesian large enterprises frequently create headaches for the consultants, since there are always be a large gap between the outcomes of the SAP with the expected results. Indonesian enterprises have experience with a huge amount of investments and ended up with minor benefits. Despite its unprecedented benefits, the SAP strategy is still considered as a mandatory enterprise system for every enterprise to compete in the marketplaces. The article examines the SAP implementation from cultural perspectives to present new horizon that commonly ignored by major Indonesian enterprises. The article applies the multiple case studies with three large Indonesia enterprises, such as KS, the largest steel producer; GEM, a subsidiary of conglomerate enterprise operates in the mining industry, and HS, a subsidiary of the largest retailer in Asia with more than 700 stores in Indonesia. The outcome of the article is expected to provide a comprehensive analysis from cultural perspectives regarding to common problems faced by SAP consultants.

  16. SAPS onset timing during substorms and the westward traveling surge

    Science.gov (United States)

    Mishin, Evgeny, V.

    2016-07-01

    We present multispacecraft observations in the magnetosphere and conjugate ionosphere of the onset time of subauroral polarization streams (SAPS) and tens of keV ring current injections on the duskside in three individual substorms. This is probably the first unequivocal determination of the substorm SAPS onset timing. The time lag between the SAPS and substorm onsets is much shorter than the gradient-curvature drift time of ˜10 keV ions in the plasmasphere. It seemingly depends on the propagation time of substorm-injected plasma from the dipolarization onset region to the plasmasphere, as well as on the SAPS position. These observations suggest that fast onset SAPS and ring current injections are causally related to the two-loop system of the westward traveling surge.

  17. A power flow method for evaluating vibration from underground railways

    Science.gov (United States)

    Hussein, M. F. M.; Hunt, H. E. M.

    2006-06-01

    One of the major sources of ground-borne vibration is the running of trains in underground railway tunnels. Vibration is generated at the wheel-rail interface, from where it propagates through the tunnel and surrounding soil into nearby buildings. An understanding of the dynamic interfaces between track, tunnel and soil is essential before engineering solutions to the vibration problem can be found. A new method has been developed to evaluate the effectiveness of vibration countermeasures. The method is based on calculating the mean power flow from the tunnel, paying attention to that part of the power which radiates upwards to places where buildings' foundations are expected to be found. The mean power is calculated for an infinite train moving through the tunnel with a constant velocity. An elegant mathematical expression for the mean power flow is derived, which can be used with any underground-tunnel model. To evaluate the effect of vibration countermeasures and track properties on power flow, a comprehensive three-dimensional analytical model is used. It consists of Euler-Bernoulli beams to account for the rails and the track slab. These are coupled in the wavenumber-frequency domain to a thin shell representing the tunnel embedded within an infinite continuum, with a cylindrical cavity representing the surrounding soil.

  18. Mechanical behaviour analyses of sap ascent in vascular plants

    Science.gov (United States)

    Perez-Diaz, Jose-Luis; Garcia-Prada, Juan-Carlos; Romera-Juarez, Fernando

    2010-01-01

    A pure mechanical anisotropic model of a tree trunk has been developed based on the 3D finite element method. It simulates the microscopic structure of vessels in the trunk of a European beech (Fagus sylvatica) in order to study and analyse its mechanical behaviour with different configurations of pressures in the conduits of xylem and phloem. The dependence of the strains at the inner bark was studied when sap pressure changed. The comparison with previously published experimental data leads to the conclusion that a great tensile stress—or ‘negative pressure’—must exist in the water column in order to achieve the measured strains if only the mechanical point of view is taken into account. Moreover, the model can help to design experiments where qualitatively knowing the strains and the purely mechanical behaviour of the tree is required. PMID:21886343

  19. Solution of plane cascade flow using improved surface singularity methods. [application of panel method to internal aerodynamics

    Science.gov (United States)

    Mcfarland, E. R.

    1981-01-01

    A solution method was developed for calculating compressible inviscid flow through a linear cascade of arbitrary blade shapes. The method uses advanced surface singularity formulations which were adapted from those in current external flow analyses. The resulting solution technique provides a fast flexible calculation for flows through turbomachinery blade rows. The solution method and some examples of the method's capabilities are presented.

  20. Numerical methods for two-phase flow with contact lines

    Energy Technology Data Exchange (ETDEWEB)

    Walker, Clauido

    2012-07-01

    This thesis focuses on numerical methods for two-phase flows, and especially flows with a moving contact line. Moving contact lines occur where the interface between two fluids is in contact with a solid wall. At the location where both fluids and the wall meet, the common continuum descriptions for fluids are not longer valid, since the dynamics around such a contact line are governed by interactions at the molecular level. Therefore the standard numerical continuum models have to be adjusted to handle moving contact lines. In the main part of the thesis a method to manipulate the position and the velocity of a contact line in a two-phase solver, is described. The Navier-Stokes equations are discretized using an explicit finite difference method on a staggered grid. The position of the interface is tracked with the level set method and the discontinuities at the interface are treated in a sharp manner with the ghost fluid method. The contact line is tracked explicitly and its dynamics can be described by an arbitrary function. The key part of the procedure is to enforce a coupling between the contact line and the Navier-Stokes equations as well as the level set method. Results for different contact line models are presented and it is demonstrated that they are in agreement with analytical solutions or results reported in the literature.The presented Navier-Stokes solver is applied as a part in a multiscale method to simulate capillary driven flows. A relation between the contact angle and the contact line velocity is computed by a phase field model resolving the micro scale dynamics in the region around the contact line. The relation of the microscale model is then used to prescribe the dynamics of the contact line in the macro scale solver. This approach allows to exploit the scale separation between the contact line dynamics and the bulk flow. Therefore coarser meshes can be applied for the macro scale flow solver compared to global phase field simulations

  1. Multiscale model of a freeze-thaw process for tree sap exudation

    CERN Document Server

    Graf, Isabell; Stockie, John M

    2015-01-01

    Sap transport in trees has long fascinated scientists, and a vast literature exists on experimental and modelling studies of trees during the growing season when large negative stem pressures are generated by transpiration from leaves. Much less attention has been paid to winter months when trees are largely dormant but nonetheless continue to exhibit interesting flow behaviour. A prime example is sap exudation, which refers to the peculiar ability of sugar maple (Acer saccharum) and related species to generate positive stem pressure while in a leafless state. Experiments demonstrate that ambient temperatures must oscillate about the freezing point before significantly heightened stem pressures are observed, but the precise causes of exudation remain unresolved. The prevailing hypothesis attributes exudation to a physical process combining freeze-thaw and osmosis, which has some support from experimental studies but remains a subject of active debate. We address this knowledge gap by developing the first math...

  2. Discontinuous Galerkin method analysis and applications to compressible flow

    CERN Document Server

    Dolejší, Vít

    2015-01-01

    The subject of the book is the mathematical theory of the discontinuous Galerkin method (DGM), which is a relatively new technique for the numerical solution of partial differential equations. The book is concerned with the DGM developed for elliptic and parabolic equations and its applications to the numerical simulation of compressible flow. It deals with the theoretical as well as practical aspects of the DGM and treats the basic concepts and ideas of the DGM, as well as the latest significant findings and achievements in this area. The main benefit for readers and the book’s uniqueness lie in the fact that it is sufficiently detailed, extensive and mathematically precise, while at the same time providing a comprehensible guide through a wide spectrum of discontinuous Galerkin techniques and a survey of the latest efficient, accurate and robust discontinuous Galerkin schemes for the solution of compressible flow.

  3. Assessment of cerebral blood flow autoregulation (CBF AR) with rheoencephalography (REG): studies in animals

    Science.gov (United States)

    Popovic, Djordje; Bodo, Michael; Pearce, Frederick; van Albert, Stephen; Garcia, Alison; Settle, Tim; Armonda, Rocco

    2013-04-01

    The ability of cerebral vasculature to regulate cerebral blood flow (CBF) in the face of changes in arterial blood pressure (SAP) or intracranial pressure (ICP) is an important guard against secondary ischemia in acute brain injuries, and official guidelines recommend that therapeutic decisions be guided by continuous monitoring of CBF autoregulation (AR). The common method for CBF AR monitoring, which rests on real-time derivation of the correlation coefficient (PRx) between slow oscillations in SAP and ICP is, however, rarely used in clinical practice because it requires invasive ICP measurements. This study investigated whether the correlation coefficient between SAP and the pulsatile component of the non-invasive transcranial bioimpedance signal (rheoencephalography, REG) could be used to assess the state and lower limit of CBF AR. The results from pigs and rhesus macaques affirm the utility of REG; however, additional animal and clinical studies are warranted to assess selectivity of automatic REG-based evaluation of CBF AR.

  4. STUDY ON SIMULATION METHOD OF AVALANCHE : FLOW ANALYSIS OF AVALANCHE USING PARTICLE METHOD

    OpenAIRE

    2015-01-01

    In this paper, modeling for the simulation of the avalanche by a particle method is discussed. There are two kinds of the snow avalanches, one is the surface avalanche which shows a smoke-like flow, and another is the total-layer avalanche which shows a flow like Bingham fluid. In the simulation of the surface avalanche, the particle method in consideration of a rotation resistance model is used. The particle method by Bingham fluid is used in the simulation of the total-layer avalanche. At t...

  5. Logically rectangular mixed methods for Darcy flow on general geometry

    Energy Technology Data Exchange (ETDEWEB)

    Arbogast, T.; Keenan, P.T.; Wheeler, M.F.; Yotov, I. [Rice Univ., Houston, TX (United States)

    1995-12-31

    The authors consider an expanded mixed finite element formulation (cell centered finite difference) for Darcy flow with a tensor absolute permeability. The reservoir can be geometrically general with internal features, but the computational domain is rectangular. The method is defined on a curvilinear grid that need not be orthogonal, obtained by mapping the rectangular, computational grid. The original flow problem becomes a similar problem with a modified permeability on the computational grid. Quadrature rules turn the mixed method into a cell-centered finite difference method with a 9 point stencil in 2-D and 19 in 3-D. As shown by theory and experiment, if the modified permeability on the computational domain is smooth, then the convergence rate is optimal and both pressure and velocity are superconvergent at certain points. If not, Lagrange multiplier pressures can be introduced on boundaries of elements so that optimal convergence is retained. This modification presents only small changes in the solution process; in fact, the same parallel domain decomposition algorithms can be applied with little or no change to the code if the modified permeability is smooth over the subdomains. This Lagrange multiplier procedure can be used to extend the difference scheme to multi-block domains, and to give a coupling with unstructured grids. In all cases, the mixed formulation is locally conservative. Computational results illustrate the advantage and convergence of this method.

  6. Methods for blood flow measurements using ultrasound contrast agents

    Science.gov (United States)

    Fowlkes, J. Brian

    2003-10-01

    Blood flow measurements using ultrasound contrast agents are being investigated for myocardial perfusion and more recently in other organ systems. The methods are based largely on the relative increase in echogenicity due to the concentration of bubbles present in the ultrasound beam. In the simplest form, regional differences in blood volume can be inferred but the possibility exists to extract perfusion from the transit of contrast agent through tissue. Perfusion measurements rely on determining the flux of blood through a tissue volume and as such require knowledge of the fractional blood volume (FBV), i.e., ml blood/g tissue and the rate of exchange, commonly measured as the mean transit time (MTT). This presentation will discuss methods of determining each of these values and their combination to estimate tissue perfusion. Underlying principles of indicator-dilution theory will be provided in the context of ultrasound contrast agents. Current methods for determining MTT will include imaging of the intravenous bolus, in-plane contrast disruption with interval and real-time contrast recovery imaging, and control of contrast agent flow using arterial disruption (contrast interruption). The advantages and limitations of the methods will be examined along with current applications. [Work supported in part by NIH.

  7. Incompressible material point method for free surface flow

    Science.gov (United States)

    Zhang, Fan; Zhang, Xiong; Sze, Kam Yim; Lian, Yanping; Liu, Yan

    2017-02-01

    To overcome the shortcomings of the weakly compressible material point method (WCMPM) for modeling the free surface flow problems, an incompressible material point method (iMPM) is proposed based on operator splitting technique which splits the solution of momentum equation into two steps. An intermediate velocity field is first obtained by solving the momentum equations ignoring the pressure gradient term, and then the intermediate velocity field is corrected by the pressure term to obtain a divergence-free velocity field. A level set function which represents the signed distance to free surface is used to track the free surface and apply the pressure boundary conditions. Moreover, an hourglass damping is introduced to suppress the spurious velocity modes which are caused by the discretization of the cell center velocity divergence from the grid vertexes velocities when solving pressure Poisson equations. Numerical examples including dam break, oscillation of a cubic liquid drop and a droplet impact into deep pool show that the proposed incompressible material point method is much more accurate and efficient than the weakly compressible material point method in solving free surface flow problems.

  8. A nearly real-time UAV video flow mosaic method

    Science.gov (United States)

    Zheng, H.; Jiang, C.; Sun, M.; Li, X. D.; Xiang, R.; Liu, Lei

    2014-12-01

    In order to solve the problem of low accuracy and high computation cost of current video mosaic methods, and also to acquire large field of view images by the unmanned aerial vehicles (UAV), which have high accuracy and high resolution, this paper propose a method for near real-time mosaic of video flow, so that we can provide essential reference data for the earthquake relief, as well as post-disaster reconstruction and recovery, in time. In this method, we obtain the flight area scope in the route planning process, and calculate the sizes of each frame with sensor sizes and altitudes. Given an overlap degree, time intervals are calculated, and key frames are extracted. After that, feature points are detected in each frame, and they are matched using Hamming distance. The RANSAC algorithm is then applied to remove error matching and calculate parameters of the transformation model. In one-strip case, the newly extracted frame is taken as the reference image in the first half, while after the middle frame is extracted, it is the reference one until the end. Experimental results show that our method can reduce the cascading error, and improve the accuracy and quality of the mosaic images, near real-time mosaic of aerial video flow is feasible.

  9. Dissection of SAP-dependent and SAP-independent SLAM family signaling in NKT cell development and humoral immunity.

    Science.gov (United States)

    Chen, Shasha; Cai, Chenxu; Li, Zehua; Liu, Guangao; Wang, Yuande; Blonska, Marzenna; Li, Dan; Du, Juan; Lin, Xin; Yang, Meixiang; Dong, Zhongjun

    2017-02-01

    Signaling lymphocytic activation molecule (SLAM)-associated protein (SAP) mutations in X-linked lymphoproliferative disease (XLP) lead to defective NKT cell development and impaired humoral immunity. Because of the redundancy of SLAM family receptors (SFRs) and the complexity of SAP actions, how SFRs and SAP mediate these processes remains elusive. Here, we examined NKT cell development and humoral immunity in mice completely deficient in SFR. We found that SFR deficiency severely impaired NKT cell development. In contrast to SAP deficiency, SFR deficiency caused no apparent defect in follicular helper T (TFH) cell differentiation. Intriguingly, the deletion of SFRs completely rescued the severe defect in TFH cell generation caused by SAP deficiency, whereas SFR deletion had a minimal effect on the defective NKT cell development in SAP-deficient mice. These findings suggest that SAP-dependent activating SFR signaling is essential for NKT cell selection; however, SFR signaling is inhibitory in SAP-deficient TFH cells. Thus, our current study revises our understanding of the mechanisms underlying T cell defects in patients with XLP. © 2017 Chen et al.

  10. Study on flow stability margin by method of system identification

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Youjie; Jiang Shengyao [Tsinghua Univ., Beijing, BJ (China). Inst. of Nuclear Energy Technology

    1999-11-01

    The main objective of the investigation is to develop a practical technology and method in engineering, based on general control theory, for distinguishing two-phase flow stability and identifying the safety margin by using the system identification method. By combining the two-phase flow stability theory in the thermo-physics field with the system stability theory and the system identification method in the field of information science, a thermo-hydraulic experiment technology with a new concept was developed. The experiment was carried out on the thermo-hydraulic test system HRTL-5 which serves as simulator to the primary circulation of the nuclear heating reactor NHR-5 and was used for investigation on its thermo-physical behavior. Reverse repeat pseudo-random sequences which were added to the steady heat flux as input signal sources and measured flow rates as response function were used in the test. The two-phase flow stability and the stability margin of the natural circulation system were investigated by analyzing the system pulse response function, the decay ratio and the stability boundary under different operational conditions. The results are compared with those obtained by using conventional methods. The test method and typical results obtained are presented in this paper. (orig.) [German] Das Hauptziel der Untersuchung ist die Entwicklung einer Technik und eines Verfahrens um - basierend auf allgemeiner Regelungstheorie - die Stabilitaet einer Zweiphasenstroemung zu bestimmen und unter Verwendung von Methoden zur Systemidentifikation Sicherheitsreserven zu ermitteln. Durch Kombination der Theorie der Zweiphasenstroemungsstabilitaet im Bereich der Thermophysik mit der Systemstabilitaetstheorie und der informationstheoretischen Systemidentifikationsmethode wurde eine thermohydraulische Experimentiertechnik neuartigen Konzepts entwickelt. Die Versuche wurden auf dem Thermohydraulikteststand HRTL-5 ausgefuehrt, der dem Primaeranlauf des Heizreaktors HHR-5

  11. Numerical method of characteristics for one-dimensional blood flow

    CERN Document Server

    Acosta, Sebastian; Riviere, Beatrice; Penny, Daniel J; Rusin, Craig G

    2014-01-01

    Mathematical modeling at the level of the full cardiovascular system requires the numerical approximation of solutions to a one-dimensional nonlinear hyperbolic system describing flow in a single vessel. This model is often simulated by computationally intensive methods like finite elements and discontinuous Galerkin, while some recent applications require more efficient approaches (e.g. for real-time clinical decision support, phenomena occurring over multiple cardiac cycles, iterative solutions to optimization/inverse problems, and uncertainty quantification). Further, the high speed of pressure waves in blood vessels greatly restricts the time-step needed for stability in explicit schemes. We address both cost and stability by presenting an efficient and unconditionally stable method for approximating solutions to diagonal nonlinear hyperbolic systems. Theoretical analysis of the algorithm is given along with a comparison of our method to a discontinuous Galerkin implementation. Lastly, we demonstrate the ...

  12. A stochastic asymptotic-preserving scheme for a kinetic-fluid model for disperse two-phase flows with uncertainty

    Science.gov (United States)

    Jin, Shi; Shu, Ruiwen

    2017-04-01

    In this paper we consider a kinetic-fluid model for disperse two-phase flows with uncertainty. We propose a stochastic asymptotic-preserving (s-AP) scheme in the generalized polynomial chaos stochastic Galerkin (gPC-sG) framework, which allows the efficient computation of the problem in both kinetic and hydrodynamic regimes. The s-AP property is proved by deriving the equilibrium of the gPC version of the Fokker-Planck operator. The coefficient matrices that arise in a Helmholtz equation and a Poisson equation, essential ingredients of the algorithms, are proved to be positive definite under reasonable and mild assumptions. The computation of the gPC version of a translation operator that arises in the inversion of the Fokker-Planck operator is accelerated by a spectrally accurate splitting method. Numerical examples illustrate the s-AP property and the efficiency of the gPC-sG method in various asymptotic regimes.

  13. A stochastic asymptotic-preserving scheme for a kinetic-fluid model for disperse two-phase flows with uncertainty

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Shi, E-mail: sjin@wisc.edu [Department of Mathematics, University of Wisconsin–Madison, Madison, WI 53706 (United States); Institute of Natural Sciences, School of Mathematical Science, MOELSEC and SHL-MAC, Shanghai Jiao Tong University, Shanghai 200240 (China); Shu, Ruiwen, E-mail: rshu2@math.wisc.edu [Department of Mathematics, University of Wisconsin–Madison, Madison, WI 53706 (United States)

    2017-04-15

    In this paper we consider a kinetic-fluid model for disperse two-phase flows with uncertainty. We propose a stochastic asymptotic-preserving (s-AP) scheme in the generalized polynomial chaos stochastic Galerkin (gPC-sG) framework, which allows the efficient computation of the problem in both kinetic and hydrodynamic regimes. The s-AP property is proved by deriving the equilibrium of the gPC version of the Fokker–Planck operator. The coefficient matrices that arise in a Helmholtz equation and a Poisson equation, essential ingredients of the algorithms, are proved to be positive definite under reasonable and mild assumptions. The computation of the gPC version of a translation operator that arises in the inversion of the Fokker–Planck operator is accelerated by a spectrally accurate splitting method. Numerical examples illustrate the s-AP property and the efficiency of the gPC-sG method in various asymptotic regimes.

  14. Modeling of Unsteady Flow through the Canals by Semiexact Method

    Directory of Open Access Journals (Sweden)

    Farshad Ehsani

    2014-01-01

    Full Text Available The study of free-surface and pressurized water flows in channels has many interesting application, one of the most important being the modeling of the phenomena in the area of natural water systems (rivers, estuaries as well as in that of man-made systems (canals, pipes. For the development of major river engineering projects, such as flood prevention and flood control, there is an essential need to have an instrument that be able to model and predict the consequences of any possible phenomenon on the environment and in particular the new hydraulic characteristics of the system. The basic equations expressing hydraulic principles were formulated in the 19th century by Barre de Saint Venant and Valentin Joseph Boussinesq. The original hydraulic model of the Saint Venant equations is written in the form of a system of two partial differential equations and it is derived under the assumption that the flow is one-dimensional, the cross-sectional velocity is uniform, the streamline curvature is small and the pressure distribution is hydrostatic. The St. Venant equations must be solved with continuity equation at the same time. Until now no analytical solution for Saint Venant equations is presented. In this paper the Saint Venant equations and continuity equation are solved with homotopy perturbation method (HPM and comparison by explicit forward finite difference method (FDM. For decreasing the present error between HPM and FDM, the st.venant equations and continuity equation are solved by HAM. The homotopy analysis method (HAM contains the auxiliary parameter ħ that allows us to adjust and control the convergence region of solution series. The study has highlighted the efficiency and capability of HAM in solving Saint Venant equations and modeling of unsteady flow through the rectangular canal that is the goal of this paper and other kinds of canals.

  15. Application of vector finite volume method for electromagnetic flow simulation

    Energy Technology Data Exchange (ETDEWEB)

    Takata, T.; Murashige, R.; Matsumoto, T.; Yamaguchi, A. [Osaka Univ., Suita, Osaka (Japan)

    2011-07-01

    A vector finite volume method (VFVM) has been developed for an electromagnetic flow analysis. In the VFVM, the governing equations of magnetic flux density and electric field intensity are solved separately so as to reduce the computational cost caused by an iterative procedure that is required to satisfy the solenoidal condition. In the present paper, a suppression of temperature fluctuation of liquid sodium after a T-junction has also been investigated with a simplified two dimensional numerical analysis by adding an obstacle (turbulence promoter) or a magnetic field after the junction. (author)

  16. Ada Apa Dengan SAP (AADS Akrual?

    Directory of Open Access Journals (Sweden)

    Eka Findi Tresnawati

    2013-08-01

    Full Text Available This article provides anoverview regarding SAP accrual-based and its problems. It compares information content of PP 24/2005’s cash toward accrual and PP 71/2010’s accrual-based toshow the urgency of accrual-based financial reporting requirements. The analysis borrows Abeysekara’s accounting imperialism. Discussion also involves empirical evidence and evaluation of accrual-based implementation probability in Sumenep Regency. Findings show that accrual-based information is not an urgent need and tends to be difficult to be implemented. Reflecting the evidence in Sumenep, local governments are faced with the need of human resources, the question of the use-fulness of accrual information, and technical difficulties on implementation.

  17. Discounted cash flow valuation methods: Examples of perpetuities, constant growth and general case

    OpenAIRE

    Fernandez, Pablo

    2005-01-01

    This paper explores the discounted cash flow valuation methods. We start the paper with the simplest case: no-growth, perpetual-life companies. Then we will study the continuous growth case and, finally, the general case. The different concepts of cash flow used in company valuation are defined: equity cash flow (ECF), free cash flow (FCF), and capital cash flow (CCF). Then the appropriate discount rate is determined for each cash flow, depending on the valuation method used. Our starting poi...

  18. Discounted cash flow valuation methods: Examples of perpetuities, constant growth and general case

    OpenAIRE

    Fernandez, Pablo

    2005-01-01

    This paper explores the discounted cash flow valuation methods. We start the paper with the simplest case: no-growth, perpetual-life companies. Then we will study the continuous growth case and, finally, the general case. The different concepts of cash flow used in company valuation are defined: equity cash flow (ECF), free cash flow (FCF), and capital cash flow (CCF). Then the appropriate discount rate is determined for each cash flow, depending on the valuation method used. Our starting poi...

  19. Particle-in-cell method in multiphase flow simulations

    Science.gov (United States)

    Zhang, Duan; Zou, Qisu; Vanderheyden, Brian

    2004-11-01

    In many disperse multiphase flows there is of great interest to know the deformations and the possibility of break up of the grains of the disperse phase. Some examples are the pneumatic transport of agriculture grains and the fragment-gas-structure interaction in an explosion. In these examples one needs to consider the stress states in both the disperse phase and the continuous phase. The use of Eulerian method encounters significant difficulties associated with numerical diffusion. The use of Lagrangian method encounters mesh-tangling problem. Expensive re-meshing procedures need to be done frequently. The particle-in-cell method possesses advantages of both methods while avoids their difficulties. A grain of the disperse phase is represented by particles. A particle in the method is not only a Lagrangian marker; it carries mass, momentum, energy and other quantities associated with the grain. Although the particle-in-cell method was invented in the sixties, its recent developments significantly enhanced its capabilities. In this presentation, we outline basic principles and numerical schemes of the particle-in-cell method and then provide examples of its applications. This work is supported by the U.S. Department of Energy. (LA-UR-04-4177)

  20. Outcome prediction in a surgical ICU using automatically calculated SAPS II scores.

    Science.gov (United States)

    Engel, J M; Junger, A; Bottger, S; Benson, M; Michel, A; Rohrig, R; Jost, A; Hempelmann, G

    2003-10-01

    The objective of this study was to establish a complete computerized calculation of the Simplified Acute Physiology Score (SAPS) II within 24 hours after admission to a surgical intensive care unit (ICU) based only on routine data recorded with a patient data management system (PDMS) without any additional manual data entry. Score calculation programs were developed using SQL scripts (Structured Query Language) to retrospectively compute the SAPS II scores of 524 patients who stayed in ICU for at least 24 hours between April 1, 1999 and March 31, 2000 out of the PDMS database. The main outcome measure was survival status at ICU discharge. Score evaluation was modified in registering missing data as being not pathological and using surrogates of the Glasgow Coma Scale (GCS). Computerized score calculation was possible for all investigated patients. The 459 (87.6%) survivors had a median SAPS II of 28 (interquartile range (IQR) 13) whereas the 65 (12.4%) decreased patients had a median score of 43 (IQR 16; P calculation, bilirubin was missing in 84%, followed by PaO2/FiO2 ratio (34%), and neurological status (34%). Using neurological diagnoses and examinations as surrogates for the GCS, a pathological finding was seen in only 8.8% of all results. The discriminative power of the computerized SAPS II checked with a receiver operating characteristic (ROC) curve was 0.81 (95% confidence interval (CI): 0.74-0.87). The Hosmer-Lemeshow goodness-of-fit statistics showed good calibration (H = 5.55, P = 0.59, 7 degrees of freedom; C = 5.55, P = 0.68, 8 degrees of freedom). The technique used in this study for complete automatic data sampling of the SAPS II score seems to be suitable for predicting mortality rate during stay in a surgical ICU. The advantage of the described method is that no additional manual data recording is required for score calculation.

  1. The lattice Boltzmann method for isothermal micro-gaseous flow and its application in shale gas flow: a review

    CERN Document Server

    Wang, Junjian; Kang, Qinjun; Rahman, Sheik S

    2016-01-01

    The lattice Boltzmann method (LBM) has experienced tremendous advances and been well accepted as a popular method of simulation of various fluid flow mechanisms on pore scale in tight formations. With the introduction of an effective relaxation time and slip boundary conditions, the LBM has been successfully extended to solve micro-gaseous related transport and phenomena. As gas flow in shale matrix is mostly in the slip flow and transition flow regimes, given the difficulties of experimental techniques to determine extremely low permeability, it appears that the computational methods especially the LBM can be an attractive choice for simulation of these micro-gaseous flows. In this paper an extensive overview on a number of relaxation time and boundary conditions used in LBM-like models for micro-gaseous flow are carried out and their advantages and disadvantages are discussed. Furthermore, potential application of the LBM in flow simulation in shale gas reservoirs on pore scale and representative elementary...

  2. Technical Note: The use of an interrupted-flow centrifugation method to characterise preferential flow in low permeability media

    Directory of Open Access Journals (Sweden)

    R. A. Crane

    2015-01-01

    Full Text Available We present an interrupted-flow centrifugation technique to characterise preferential flow in low permeability media. The method entails a minimum of three phases: centrifuge induced flow, no flow and centrifuge induced flow, which may be repeated several times in order to most effectively characterise multi-rate mass transfer behaviour. In addition, the method enables accurate simulation of relevant in situ total stress conditions during flow by selecting an appropriate centrifugal force level. We demonstrate the utility of the technique for characterising the hydraulic properties of smectite clay dominated core samples. All samples exhibited a non-Fickian tracer breakthrough (early tracer arrival, combined with a decrease in tracer concentration immediately after each period of interrupted-flow. This is indicative of dual (or multi porosity behaviour, with solute migration predominately via advection during induced flow, and via molecular diffusion (between the preferential flow network(s and the low hydraulic conductivity domain during interrupted-flow. Tracer breakthrough curves were simulated using a bespoke dual porosity model with excellent agreement between the data and model output (Nash–Sutcliffe model efficiency coefficient was >0.97 for all samples. In combination interrupted-flow centrifuge experiments and dual porosity transport modelling are shown to be a powerful method to characterise preferential flow in low permeability media.

  3. Methods for early prediction of lactation flow in Holstein heifers

    Directory of Open Access Journals (Sweden)

    Vesna Gantner

    2010-12-01

    Full Text Available The aim of this research was to define methods for early prediction (based on I. milk control record of lactation flow in Holstein heifers as well as to choose optimal one in terms of prediction fit and application simplicity. Total of 304,569 daily yield records automatically recorded on a 1,136 first lactation Holstein cows, from March 2003 till August 2008., were included in analysis. According to the test date, calving date, the age at first calving, lactation stage when I. milk control occurred and to the average milk yield in first 25th, T1 (and 25th-45th, T2 lactation days, measuring monthcalving month-age-production-time-period subgroups were formed. The parameters of analysed nonlinear and linear methods were estimated for each defined subgroup. As models evaluation measures,adjusted coefficient of determination, and average and standard deviation of error were used. Considering obtained results, in terms of total variance explanation (R2 adj, the nonlinear Wood’s method showed superiority above the linear ones (Wilmink’s, Ali-Schaeffer’s and Guo-Swalve’s method in both time-period subgroups (T1 - 97.5 % of explained variability; T2 - 98.1 % of explained variability. Regarding the evaluation measures based on prediction error amount (eavg±eSD, the lowest average error of daily milk yield prediction (less than 0.005 kg/day, as well as of lactation milk yield prediction (less than 50 kg/lactation (T1 time-period subgroup and less than 30 kg/lactation (T2 time-period subgroup; were determined when Wood’s nonlinear prediction method were applied. Obtained results indicate that estimated Wood’s regression parameters could be used in routine work for early prediction of Holstein heifer’s lactation flow.

  4. Particle Methods for Geophysical Flow on the Sphere

    Science.gov (United States)

    Bosler, Peter A.

    We present a Lagrangian Particle-Panel Method (LPPM) for geophysical fluid flow on a rotating sphere motivated by problems in atmosphere and ocean dynamics. We focus here on the barotropic vorticity equation and 2D passive scalar advection, as a step towards the development of a new dynamical core for global circulation models. The LPPM method employs the Lagrangian form of the equations of motion. The flow map is discretized as a set of Lagrangian particles and panels. Particle velocity is computed by applying a midpoint rule/point vortex approximation to the Biot-Savart integral with quadrature weights determined by the panel areas. We consider several discretizations of the sphere including the cubed sphere mesh, icosahedral triangles, and spherical Voronoi tesselations. The ordinary differential equations for particle motion are integrated by the fourth order Runge-Kutta method. Mesh distortion is addressed using a combination of adaptive mesh refinement (AMR) and a new Lagrangian remeshing procedure. In contrast with Eulerian schemes, the LPPM method avoids explicit discretization of the advective derivative. In the case of passive scalar advection, LPPM preserves tracer ranges and both linear and nonlinear tracer correlations exactly. We present results for the barotropic vorticity equation applied to several test cases including solid body rotation, Rossby-Haurwitz waves, Gaussian vortices, jet streams, and a model for the breakdown of the polar vortex during sudden stratospheric warming events. The combination of AMR and remeshing enables the LPPM scheme to efficiently resolve thin fronts and filaments that develop in the vorticity distribution. We validate the accuracy of LPPM by comparing with results obtained using the Eulerian based Lin-Rood advection scheme. We examine how energy and enstrophy conservation in the LPPM scheme are affected by the time step and spatial discretization. We conclude with a discussion of how the method may be extended to the

  5. Fast multipole method applied to Lagrangian simulations of vortical flows

    Science.gov (United States)

    Ricciardi, Túlio R.; Wolf, William R.; Bimbato, Alex M.

    2017-10-01

    Lagrangian simulations of unsteady vortical flows are accelerated by the multi-level fast multipole method, FMM. The combination of the FMM algorithm with a discrete vortex method, DVM, is discussed for free domain and periodic problems with focus on implementation details to reduce numerical dissipation and avoid spurious solutions in unsteady inviscid flows. An assessment of the FMM-DVM accuracy is presented through a comparison with the direct calculation of the Biot-Savart law for the simulation of the temporal evolution of an aircraft wake in the Trefftz plane. The role of several parameters such as time step restriction, truncation of the FMM series expansion, number of particles in the wake discretization and machine precision is investigated and we show how to avoid spurious instabilities. The FMM-DVM is also applied to compute the evolution of a temporal shear layer with periodic boundary conditions. A novel approach is proposed to achieve accurate solutions in the periodic FMM. This approach avoids a spurious precession of the periodic shear layer and solutions are shown to converge to the direct Biot-Savart calculation using a cotangent function.

  6. Multi-scale simulation method for electroosmotic flows

    Science.gov (United States)

    Guo, Lin; Chen, Shiyi; Robbins, Mark O.

    2016-10-01

    Electroosmotic transport in micro-and nano- channels has important applications in biological and engineering systems but is difficult to model because nanoscale structure near surfaces impacts flow throughout the channel. We develop an efficient multi-scale simulation method that treats near-wall and bulk subdomains with different physical descriptions and couples them through a finite overlap region. Molecular dynamics is used in the near-wall subdomain where the ion density is inconsistent with continuum models and the discrete structure of solvent molecules is important. In the bulk region the solvent is treated as a continuum fluid described by the incompressible Navier-Stokes equations with thermal fluctuations. A discrete description of ions is retained because of the low density of ions and the long range of electrostatic interactions. A stochastic Euler-Lagrangian method is used to simulate the dynamics of these ions in the implicit continuum solvent. The overlap region allows free exchange of solvent and ions between the two subdomains. The hybrid approach is validated against full molecular dynamics simulations for different geometries and types of flows.

  7. Finite Spectral Semi-Lagrangian Method for Incompressible Flows

    Institute of Scientific and Technical Information of China (English)

    LI Shao-Wu; WANG Jian-Ping

    2012-01-01

    A new semi-Lagrangian (SL) scheme is proposed by using finite spectral regional interpolation and adequate numerical dissipation to control the nonlinear instability. The finite spectrai basis function is C1 continuous at the boundary and is easy to construct. Comparison between numerical and experimental results indicates that the present method works well in solving incompressible Navier-Stokes equations for unsteady Sows around airfoil with different angles of attack.%A new semi-Lagrangian (SL) scheme is proposed by using finite spectral regional interpolation and adequate numerical dissipation to control the nonlinear instability.The finite spectral basis function is C1 continuous at the boundary and is easy to construct.Comparison between numerical and experimental results indicates that the present method works well in solving incompressible Navier-Stokes equations for unsteady flows around airfoil with different angles of attack.

  8. Flow resistance and its prediction methods in compound channels

    Institute of Scientific and Technical Information of China (English)

    Kejun Yang; Shuyou Cao; Xingnian Liu

    2007-01-01

    A series of experiments was carried out in a large symmetric compound channel composed of a rough main channel and rough floodplains to investigate the resistance characteristics of inbank and overbank flows.The effective Manning,Darcy-Weisbach,Chezy coefficients and the relative Nikuradse roughness height were analyzed.Many different representative methods for predicting the composite roughness were systemat-ically summarized.Besides the measured data,a vast number of laboratory data and field data for compoundchannels were collected and used to check the valid-ity of these methods for different subsection divisionsincluding the vertical,horizontal,diagonal and bisec-tional divisions.The computation showed that thesemethods resulted in big errors in assessing the compos-ite roughness in compound channels,and the reasonswere analyzed in detail.The error magnitude is relatedto the subsection divisions.

  9. Dynamic economic dispatch combining network flow and interior point method

    Institute of Scientific and Technical Information of China (English)

    韩学山; 赵建国; 柳焯

    2003-01-01

    Under the environment of electric power market, economic dispatch (ED) problem should consider network constraints, unit ramp rates, besides the basic constraints. For this problem, it is important to establish the effective model and algorithm. This paper examines the decoupled conditions that affect the solution optimality to this problem. It proposes an effective model and solution method. Based on the look-ahead technique, it finds the number of time intervals to guarantee the solution optimality. Next, an efficient technique for finding the optimal solution via the interior point methods is described. Test cases, which include dispatching six units over 5 time intervals on the IEEE 30 test system with line flows and ramp constraints are presented. Results indicate that the computational effort as measured by iteration counts or execution time varies only modestly with the problem size.

  10. A rotational compressible inverse design method for internal flow configurations

    Science.gov (United States)

    Dedoussis, V.; Chaviaropoulos, P.; Papailiou, K. D.

    The development of a rotational inviscid compressible inverse design method for two-dimensional internal flow configurations is described. Rotationality is due to an incoming entropy gradient, while total enthalpy is considered to be constant throughout the flowfield. The method is based on the potential function-streamfunction formulation. A novel procedure based on differential geometry arguments is employed to derive the governing equation for velocity by requiring the curvature of the two-dimensional Euclidean space to be zero. The velocity equation solved in conjunction with a transport equation for a thermal drift function provide the flowfield without any geometry feedback. An auxiliary orthogonal computational grid adapted to the solution is employed. Geometry is determined by integrating Frenet equations of the grid lines. Inverse calculation results are compared with results of direct reproduction calculations.

  11. Adaptive discontinuous Galerkin methods for non-linear reactive flows

    CERN Document Server

    Uzunca, Murat

    2016-01-01

    The focus of this monograph is the development of space-time adaptive methods to solve the convection/reaction dominated non-stationary semi-linear advection diffusion reaction (ADR) equations with internal/boundary layers in an accurate and efficient way. After introducing the ADR equations and discontinuous Galerkin discretization, robust residual-based a posteriori error estimators in space and time are derived. The elliptic reconstruction technique is then utilized to derive the a posteriori error bounds for the fully discrete system and to obtain optimal orders of convergence. As coupled surface and subsurface flow over large space and time scales is described by (ADR) equation the methods described in this book are of high importance in many areas of Geosciences including oil and gas recovery, groundwater contamination and sustainable use of groundwater resources, storing greenhouse gases or radioactive waste in the subsurface.

  12. Method and apparatus for controlling the flow rate of mercury in a flow system

    Science.gov (United States)

    Grossman, Mark W.; Speer, Richard

    1991-01-01

    A method for increasing the mercury flow rate to a photochemical mercury enrichment utilizing an entrainment system comprises the steps of passing a carrier gas over a pool of mercury maintained at a first temperature T1, wherein the carrier gas entrains mercury vapor; passing said mercury vapor entrained carrier gas to a second temperature zone T2 having temperature less than T1 to condense said entrained mercury vapor, thereby producing a saturated Hg condition in the carrier gas; and passing said saturated Hg carrier gas to said photochemical enrichment reactor.

  13. CyNC - a method for Real Time Analysis of Systems with Cyclic Data Flows

    DEFF Research Database (Denmark)

    Schiøler, Henrik; Nielsen, Jens F. Dalsgaard; Larsen, Kim Guldstrand

    2005-01-01

    The paper addresses a novel method for realtime analysis of systems with cyclic data flows. The presented method is based on Network Calculus principles, where upper and lower flow and service constraint are used to bound data flows and processing resources. In acyclic systems flow constraints may...

  14. Immersed boundary method predictions of shear stresses for different flow topologies occuring in cerebral aneurysms

    NARCIS (Netherlands)

    Mikhal, Julia Olegivna; Pereira, J.C.F; Sequeira, A.; Lopez Penha, D.J.; Slump, Cornelis H.; Pereira, J.M.C.; Janela, J.; Geurts, Bernardus J.; Borges, L.

    A volume-penalizing immersed boundary method is presented that facilitates the computation of incompressible fluid flow in complex flow domains. We apply this method to simulate the flow in cerebral aneurysms, and focus on the accuracy with which the flow field and the corresponding shear stress

  15. Modeling of Occurrence and Dynamics of Sub-Auroral Polarization Streams (SAPS) During Storm and Non-Storm Conditions

    Science.gov (United States)

    Sazykin, S. Y.; Huba, J.; Coster, A. J.; Wolf, R.; Erickson, P. J.; Reiff, P. H.; Hairston, M. R.; Shepherd, S. G.; Baker, J. B. H.; Ruohoniemi, J. M.; Califf, S.

    2016-12-01

    Occurrence and evolution of Sub-Auroral Polarization Stream, or SAPS, structures, defined here as latitudinally narrow channels of enhanced westward convection flows in the evening ionosphere equatorward of the auroral electron precipitation boundary, is the subject of the ongoing CEDAR-GEM focus study. In this paper, we present simulation results of several event intervals selected for the focus study, obtained with the SAMI3-RCM ionosphere-magnetosphere coupled model. We simulate intervals that include quiet-times, storm main phases, and storm recovery phases, as well as non-storm intervals with variations in the high-latitude convection. We compare simulation results with multi-instrument observations. In the ionosphere, these include mid-latitude SuperDARN Doppler flow velocities, DMSP topside ionospheric ExB drifts, Millstone Hill incoherent scatter flow velocities and F-region densities, and ground-based GPS Total Electron Content (TEC) maps. Magnetospheric data used for model comparison are electric field and cold plasma densities from Van Allen Probes and plasma and fields measurements by the Magnetospheric Multiscale Mission (MMS) probes. Through comparing modeling results and data, we address the following questions: (1) Can observed occurrence of SAPS be predicted by the model based on time history of magnetospheric activity? (2) To what extent does non-linear ionospheric feedback affect dynamics of SAPS? (3) How does the preconditioning of the background ionosphere (specifically, night-time main ionospheric trough) affect SAPS dynamics? (4) How does presence of SAPS structures in the global ionospheric convection pattern affect storm-time plasma re-distribution (e.g., storm-enhanced densities (or SEDs), plasmaspheric plumes, traveling ionospheric disturbances (or TIDs))?

  16. An Analysis of Internal Flow of Diagonal Flow Blower with Quasi-Three-Dimensional Calculation Method Considering the Spanwise Mixing due to Secondary Flow

    Energy Technology Data Exchange (ETDEWEB)

    Park, S.R. [Inha University, Inchon (Korea); Kim, Y.J.; Kim, T.W. [Doowon Technical College, Ansung (Korea)

    1999-12-01

    This paper presents a quasi-three-dimensional calculation method considered a spanwise mixing effect in a diagonal flow impeller. The effect of this spanwise mixing caused by spanwise distribution of blade loading is evaluated by a secondary flow theory. In order to verify the validity of this method, it is applied to the analysis of a diagonal flow fan designed under a vortex type of constant circumferential velocity and that of a free vortex. The comparison of the calculated result with experimental data shows a good agreement except the regions near the casing where the flow field is affected by the tip leakage flow. (author). 18 refs., 10 figs.

  17. 30 CFR 285.605 - What is a Site Assessment Plan (SAP)?

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What is a Site Assessment Plan (SAP)? 285.605... Assessment Plan (SAP)? (a) A SAP describes the activities (e.g., installation of meteorological towers... project easement, or to test technology devices. (1) Your SAP must describe how you will conduct your...

  18. 30 CFR 285.614 - When may I begin conducting activities under my approved SAP?

    Science.gov (United States)

    2010-07-01

    ... approved SAP? 285.614 Section 285.614 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE... Plans and Information Requirements Activities Under An Approved Sap § 285.614 When may I begin conducting activities under my approved SAP? (a) You may begin conducting the activities approved in your SAP...

  19. Characteristic Profiles of an Original Drink Sap from Male and Female Deglet Nour Palm (Phoenix dactylifera L. during Collection Period

    Directory of Open Access Journals (Sweden)

    Ines Makhlouf-Gafsi

    2016-01-01

    Full Text Available This work aimed to evaluate the nutritional quality of a typical natural drink from male and female Deglet Nour (DN date palm (Phoenix dactylifera L. during the collection period. Dry matter, protein, amino acids, and sugar profiles were determined using AFNOR norm, Kjeldahl method, HPLC, and HPAEC-PAD, respectively. The male sap dry matter content was higher than that of the female. It decreased significantly through the tapping period. During the harvest, the male sap protein content decreased but increased significantly in the female sap. Finally, sugar fraction, for both male and female DN sap, was dominated by sucrose, glucose, fructose, and a small amount of myo-inositol. During the collection time, sugar content is affected by the sex especially for myo-inositol content that increased significantly in the female date sap, unlike that of the male one. This may be related to the fact that the male palm is more resistant to physiological stress, inducing myo-inositol formation during tapping.

  20. Integrated Debris Flow Disaster Mitigation -A Comprehensive Method for Debris Flow Disaster Mitigation

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Integrated disaster mitigation needs interpreting torrent catchment areas as complex landscape systems. The history of valley-evolution shows the influence of climate and vegetation on the valley-evolution. The energy-concept (energy dissipation concept including the idea of the energy-line) is used for a simple explanation of debris flow. Examples of heavy debris flow disasters in controlled torrents in the Alps and Pyrenees give hints, which expanding the time scale can show that side-effects restrict or counteract the mitigation measures. A pallet of different mitigation measures to avoid or to reduce some of the side-effects is shown. The comprehensive method of disaster mitigation also includes the effect of vegetation. The pallet includes: avoiding hazards (hazard mapping, warning and alarming), appropriate land use and avoiding disaster-enhancing measures in the landscape and technical measures, which take into account their side-effects. The energy line is used as simple design theory. The Jiu-Jitsu Principle is explained too. With this comprehensive method a more sustainable reduction of disasters seems possible.

  1. Bluff Body Flow Simulation Using a Vortex Element Method

    Energy Technology Data Exchange (ETDEWEB)

    Anthony Leonard; Phillippe Chatelain; Michael Rebel

    2004-09-30

    Heavy ground vehicles, especially those involved in long-haul freight transportation, consume a significant part of our nation's energy supply. it is therefore of utmost importance to improve their efficiency, both to reduce emissions and to decrease reliance on imported oil. At highway speeds, more than half of the power consumed by a typical semi truck goes into overcoming aerodynamic drag, a fraction which increases with speed and crosswind. Thanks to better tools and increased awareness, recent years have seen substantial aerodynamic improvements by the truck industry, such as tractor/trailer height matching, radiator area reduction, and swept fairings. However, there remains substantial room for improvement as understanding of turbulent fluid dynamics grows. The group's research effort focused on vortex particle methods, a novel approach for computational fluid dynamics (CFD). Where common CFD methods solve or model the Navier-Stokes equations on a grid which stretches from the truck surface outward, vortex particle methods solve the vorticity equation on a Lagrangian basis of smooth particles and do not require a grid. They worked to advance the state of the art in vortex particle methods, improving their ability to handle the complicated, high Reynolds number flow around heavy vehicles. Specific challenges that they have addressed include finding strategies to accurate capture vorticity generation and resultant forces at the truck wall, handling the aerodynamics of spinning bodies such as tires, application of the method to the GTS model, computation time reduction through improved integration methods, a closest point transform for particle method in complex geometrics, and work on large eddy simulation (LES) turbulence modeling.

  2. A Parallel Probabilistic Load Flow Method Considering Nodal Correlations

    Directory of Open Access Journals (Sweden)

    Jun Liu

    2016-12-01

    Full Text Available With the introduction of more and more random factors in power systems, probabilistic load flow (PLF has become one of the most important tasks for power system planning and operation. Cumulants-based PLF is an effective algorithm to calculate PLF in an analytical way, however, the correlations among the nodal injections to the system level have rarely been studied. A novel parallel cumulants-based PLF method considering nodal correlations is proposed in this paper, which is able to deal with the correlations among all system nodes, and avoid the Jacobian matrix inversion in the traditional cumulants-based PLF as well. In addition, parallel computing is introduced to improve the efficiency of the numerical calculations. The accuracy of the proposed method is validated by numerical tests on the standard IEEE-14 system, comparing with the results from Correlation Latin hypercube sampling Monte Carlo Simulation (CLMCS method. And the efficiency and parallel performance is proven by the tests on the modified IEEE-300, C703, N1047 systems with distributed generation (DG. Numerical simulations show that the proposed parallel cumulants-based PLF method considering nodal correlations is able to get more accurate results using less computational time and physical memory, and have higher efficiency and better parallel performance than the traditional one.

  3. Tensor product decomposition methods applied to complex flow data

    Science.gov (United States)

    von Larcher, Thomas; Klein, Rupert; Schneider, Reinhold; Wolf, Sebastian; Huber, Benjamin

    2017-04-01

    Low-rank multilevel approximation methods are an important tool in numerical analysis and in scientific computing. Those methods are often suited to attack high-dimensional problems successfully and allow very compact representations of large data sets. Specifically, hierarchical tensor product decomposition methods emerge as an promising approach for application to data that are concerned with cascade-of-scales problems as, e.g., in turbulent fluid dynamics. We focus on two particular objectives, that is representing turbulent data in an appropriate compact form and, secondly and as a long-term goal, finding self-similar vortex structures in multiscale problems. The question here is whether tensor product methods can support the development of improved understanding of the multiscale behavior and whether they are an improved starting point in the development of compact storage schemes for solutions of such problems relative to linear ansatz spaces. We present the reconstruction capabilities of a tensor decomposition based modeling approach tested against 3D turbulent channel flow data.

  4. Flow Diode and Method for Controlling Fluid Flow Origin of the Invention

    Science.gov (United States)

    Dyson, Rodger W (Inventor)

    2015-01-01

    A flow diode configured to permit fluid flow in a first direction while preventing fluid flow in a second direction opposite the first direction is disclosed. The flow diode prevents fluid flow without use of mechanical closures or moving parts. The flow diode utilizes a bypass flowline whereby all fluid flow in the second direction moves into the bypass flowline having a plurality of tortuous portions providing high fluidic resistance. The portions decrease in diameter such that debris in the fluid is trapped. As fluid only travels in one direction through the portions, the debris remains trapped in the portions.

  5. Finite volume methods for submarine debris flows and generated waves

    Science.gov (United States)

    Kim, Jihwan; Løvholt, Finn; Issler, Dieter

    2016-04-01

    Submarine landslides can impose great danger to the underwater structures and generate destructive tsunamis. Submarine debris flows often behave like visco-plastic materials, and the Herschel-Bulkley rheological model is known to be appropriate for describing the motion. In this work, we develop numerical schemes for the visco-plastic debris flows using finite volume methods in Eulerian coordinates with two horizontal dimensions. We provide parameter sensitivity analysis and demonstrate how common ad-hoc assumptions such as including a minimum shear layer depth influence the modeling of the landslide dynamics. Hydrodynamic resistance forces, hydroplaning, and remolding are all crucial terms for underwater landslides, and are hence added into the numerical formulation. The landslide deformation is coupled to the water column and simulated in the Clawpack framework. For the propagation of the tsunamis, the shallow water equations and the Boussinesq-type equations are employed to observe how important the wave dispersion is. Finally, two cases in central Norway, i.e. the subaerial quick clay landslide at Byneset in 2012, and the submerged tsunamigenic Statland landslide in 2014, are both presented for validation. The research leading to these results has received funding from the Research Council of Norway under grant number 231252 (Project TsunamiLand) and the European Union's Seventh Framework Programme (FP7/2007-2013) under grant agreement 603839 (Project ASTARTE).

  6. The installations maintenance control using SAP R/3; O controle de manutencao de instalacoes utilizando o SAP R/3

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, Robison Tirre; Pereira, Paulo Manoel Borges; Jorge, Kemal Vieira [Transportadora Brasileira Gasoduto Bolivia Brasil S.A., Rio de Janeiro, RJ (Brazil)

    2004-07-01

    TBG (Transportadora Brasileira Gasoduto Bolivia Brasil S.A.) began their operations in 1999 and since the beginning the SAP R/3 PM module (Plant Maintenance) is used for the control of the maintenance activities and to manager the Master Maintenance and Inspection Plans. On these five years, a series of reports and SAP functionalities were developed or configured to adapt the system R/3 to the needs of TBG maintenance. Now, the whole management and control of the surface facilities maintenance (compression station, city gate, measurement station, etc) is accomplished by SAP R/3 system. (author)

  7. Nuclear magnetic response imaging of sap flow in plants

    NARCIS (Netherlands)

    Windt, C.W.

    2007-01-01

    This thesis deals with Nuclear Magnetic Resonance (NMR) imaging of long distance transport in plants. Long distance transport in plants is an enigmatic process. The theoretical framework that describes its basic properties has been in place for almost a century, yet at the same time only little is

  8. Universality of osmotically driven sap-flow in plants

    Science.gov (United States)

    Bohr, Tomas; Hartvig Jensen, Kåre; Berg Sørensen, Kirstine; Mørch Friis, Søren; Liesche, Johannes; Schulz, Alexander

    2011-11-01

    Since Ernst Münch in the 1920s proposed that sugar transport in the phloem vascular system of plants is driven by passive osmotic pressure gradients, it has been strongly debated whether this hypothesis can account even for long distance translocation. Recently, it was shown that theoretical optimization of the Münch mechanism leads to surprisingly simple predictions for the dimensions of the phloem sieve elements in relation to those of the plants [Jensen et. al., J. Roy. Soc. Interface 8, pp. 1155-1165 (2011)]. We show that the theoretical results are very insensitive to the details of the sugar-loading (in leaves) and unloading (in shoots or roots) and can even be obtained from a simple coupled resistor model. We have compiled anatomical data for a wide group of plants and find good agreement with theory, even for conifer trees, in which the sugar translocation is substantially slower than hardwood trees.

  9. Characterization of methacrylated alginate and acrylic monomers as versatile SAPs.

    Science.gov (United States)

    Mignon, Arn; Vermeulen, Jolien; Graulus, Geert-Jan; Martins, José; Dubruel, Peter; De Belie, Nele; Van Vlierberghe, Sandra

    2017-07-15

    Superabsorbent polymers (SAPs) based on polysaccharides, especially alginate, could offer a valuable solution in a plethora of applications going from drug delivery to self-healing concrete. This has already been proven with both calcium alginate and methacrylated alginate combined with acrylic acid. In this manuscript, the effect of varying the degree of methacrylation and use of a combination of acrylic acid and acrylamide is investigated to explore the effects on the relevant SAP characteristics. The materials showed high gel fractions and a strong swelling capacity up to 630gwater/gSAP, especially for superabsorbent polymers with a low degree of substitution. The SAPs also showed only a limited hydrolysis in aqueous and cement filtrate solutions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  10. Investigation potential flow about swept back wing using panel method

    Directory of Open Access Journals (Sweden)

    WakkasAli Rasheed, NabeelAbdulhadiGhyadh, Sahib Shihab Ahmed

    2016-01-01

    Full Text Available In the present investigation Low order panel method with Dirichlet boundary condition conjugated with Kutta condition, was used to calculate pressure coefficients for potential flow about isolated swept back wings at different aspect ratios and different angles of attack. Also both local and total lift coefficients were calculated for the same wings, with detailed streamline behavior on both upper and lower surface. Constant strength quadrilateral doublet element and Constant strength quadrilateral source element were placed on each panel, except on wake sheet only constant strength quadrilateral doublets were placed to satisfy Kutta condition at trailing edge. A set of linear algebraic equations were established by setting inner potential equals to free stream potential. These equations were solved using Gauss-elimination to determine quadrilateral doublet singularity strength distribution. Finally finite difference formula was used to predict aerodynamic loads calculation.

  11. Convection in multiphase flows using Lattice Boltzmann methods

    CERN Document Server

    Biferale, L; Sbragaglia, M; Toschi, F

    2011-01-01

    We present high resolution numerical simulations of convection in multiphase flows (boiling) using a novel algorithm based on a Lattice Boltzmann method. We first validate the thermodynamical and kinematical properties of the algorithm. Then, we perform a series of 3d numerical simulations at changing the mean properties in the phase diagram and compare convection with and without phase coexistence at $Ra \\sim 10^7$. We show that in presence of nucleating bubbles non-Oberbeck Boussinesq effects develops, mean temperature profile becomes asymmetric, heat-transfer and heat-transfer fluctuations are enhanced. We also show that small-scale properties of velocity and temperature fields are strongly affected by the presence of buoyant bubble leading to high non-Gaussian profiles in the bulk.

  12. Valuing instream flows using the hedonic price method

    Science.gov (United States)

    Netusil, Noelwah R.; Summers, Matthew T.

    2009-11-01

    The Oregon Water Trust (OWT) uses a market-based approach to protect and enhance instream flows in Oregon. We use the hedonic price method to estimate the effect of numerous variables on the annualized price OWT pays for water rights: the amount of water protected by the transaction, transaction type (state approved or contractual agreement), presence of anadromous and/or resident fish, and if a fish is listed under the Endangered Species Act (ESA). We find evidence of a premium for state-approved transactions and for transactions that protect water in streams with listed species. Adjusting the amount of water protected by each transaction to include only rights that will be delivered with a high degree of certainty produces coefficient estimates that are similar, but more accurate, than using unadjusted water rights amounts.

  13. Methods for estimating flow-duration and annual mean-flow statistics for ungaged streams in Oklahoma

    Science.gov (United States)

    Esralew, Rachel A.; Smith, S. Jerrod

    2010-01-01

    Flow statistics can be used to provide decision makers with surface-water information needed for activities such as water-supply permitting, flow regulation, and other water rights issues. Flow statistics could be needed at any location along a stream. Most often, streamflow statistics are needed at ungaged sites, where no flow data are available to compute the statistics. Methods are presented in this report for estimating flow-duration and annual mean-flow statistics for ungaged streams in Oklahoma. Flow statistics included the (1) annual (period of record), (2) seasonal (summer-autumn and winter-spring), and (3) 12 monthly duration statistics, including the 20th, 50th, 80th, 90th, and 95th percentile flow exceedances, and the annual mean-flow (mean of daily flows for the period of record). Flow statistics were calculated from daily streamflow information collected from 235 streamflow-gaging stations throughout Oklahoma and areas in adjacent states. A drainage-area ratio method is the preferred method for estimating flow statistics at an ungaged location that is on a stream near a gage. The method generally is reliable only if the drainage-area ratio of the two sites is between 0.5 and 1.5. Regression equations that relate flow statistics to drainage-basin characteristics were developed for the purpose of estimating selected flow-duration and annual mean-flow statistics for ungaged streams that are not near gaging stations on the same stream. Regression equations were developed from flow statistics and drainage-basin characteristics for 113 unregulated gaging stations. Separate regression equations were developed by using U.S. Geological Survey streamflow-gaging stations in regions with similar drainage-basin characteristics. These equations can increase the accuracy of regression equations used for estimating flow-duration and annual mean-flow statistics at ungaged stream locations in Oklahoma. Streamflow-gaging stations were grouped by selected drainage

  14. Sap-Sugar Content of Grafted Sugar Maple Trees

    Science.gov (United States)

    Maurice E. Jr. Demeritt; Maurice E. Jr. Demeritt

    1985-01-01

    In March and April 1983, 289 and 196 young grafted sugar maple trees were tapped and evaluated for sap-sugar content. In April, sap was collected from taps both above and below the graft union. Diameter of all tapped trees at 18 inches above the ground was measured. Analysis of the data revealed that: (1) trees selected for high sugar yield cannot be reproduced by...

  15. Numerical spectral methods applied to flow in highly heterogeneous aquifers

    Energy Technology Data Exchange (ETDEWEB)

    Van Lent, T.J.

    1992-01-01

    The small perturbation approximation is of central importance to many of the current stochastic approaches to groundwater flow and transport. However, the range of validity of this approximation is not clear. In this thesis, the author applies a numerical spectral approach to investigate the range of validity of the small perturbation approximation for head and specific discharge moments in one- and two-dimensional finite domains. The objectives of this thesis are three-fold. First, to investigate numerical Fourier methods applicable to periodic domains. This periodic formulation allows an approximation to stationarity to an arbitrary degree. Secondly, apply Fourier methods to the numerical derivation of generalized covariance functions of head and specific discharge using a small perturbation approximation. Lastly, use the numerical spectral methods to investigate the range of validity of the small perturbation approximation for head and specific discharge moments. The findings are that the small perturbation approximation tends to underestimate the variance of large-scale head and specific discharge fluctuations, and error increases with increasing log-conductivity variance. Moreover, the validity of the small perturbation approximating for head depends upon log-conductivity variance, initial log-conductivity covariance function, and domain size. The head fluctuations are not ergodic. The specific discharge fluctuations, on the other hand, do appear ergodic. The specific discharge moments are less affected by initial log-conductivity covariance choice. The small perturbation approximation performs well in estimating total variance in the longitudinal direction, but underestimates transverse specific discharge variance.

  16. A Finite Element Method for Simulation of Compressible Cavitating Flows

    Science.gov (United States)

    Shams, Ehsan; Yang, Fan; Zhang, Yu; Sahni, Onkar; Shephard, Mark; Oberai, Assad

    2016-11-01

    This work focuses on a novel approach for finite element simulations of multi-phase flows which involve evolving interface with phase change. Modeling problems, such as cavitation, requires addressing multiple challenges, including compressibility of the vapor phase, interface physics caused by mass, momentum and energy fluxes. We have developed a mathematically consistent and robust computational approach to address these problems. We use stabilized finite element methods on unstructured meshes to solve for the compressible Navier-Stokes equations. Arbitrary Lagrangian-Eulerian formulation is used to handle the interface motions. Our method uses a mesh adaptation strategy to preserve the quality of the volumetric mesh, while the interface mesh moves along with the interface. The interface jump conditions are accurately represented using a discontinuous Galerkin method on the conservation laws. Condensation and evaporation rates at the interface are thermodynamically modeled to determine the interface velocity. We will present initial results on bubble cavitation the behavior of an attached cavitation zone in a separated boundary layer. We acknowledge the support from Army Research Office (ARO) under ARO Grant W911NF-14-1-0301.

  17. River Flow Prediction Using the Nearest Neighbor Probabilistic Ensemble Method

    Directory of Open Access Journals (Sweden)

    H. Sanikhani

    2016-02-01

    Full Text Available Introduction: In the recent years, researchers interested on probabilistic forecasting of hydrologic variables such river flow.A probabilistic approach aims at quantifying the prediction reliability through a probability distribution function or a prediction interval for the unknown future value. The evaluation of the uncertainty associated to the forecast is seen as a fundamental information, not only to correctly assess the prediction, but also to compare forecasts from different methods and to evaluate actions and decisions conditionally on the expected values. Several probabilistic approaches have been proposed in the literature, including (1 methods that use resampling techniques to assess parameter and model uncertainty, such as the Metropolis algorithm or the Generalized Likelihood Uncertainty Estimation (GLUE methodology for an application to runoff prediction, (2 methods based on processing the forecast errors of past data to produce the probability distributions of future values and (3 methods that evaluate how the uncertainty propagates from the rainfall forecast to the river discharge prediction, as the Bayesian forecasting system. Materials and Methods: In this study, two different probabilistic methods are used for river flow prediction.Then the uncertainty related to the forecast is quantified. One approach is based on linear predictors and in the other, nearest neighbor was used. The nonlinear probabilistic ensemble can be used for nonlinear time series analysis using locally linear predictors, while NNPE utilize a method adapted for one step ahead nearest neighbor methods. In this regard, daily river discharge (twelve years of Dizaj and Mashin Stations on Baranduz-Chay basin in west Azerbijan and Zard-River basin in Khouzestan provinces were used, respectively. The first six years of data was applied for fitting the model. The next three years was used to calibration and the remained three yeas utilized for testing the models

  18. Large-eddy simulation of flows past a flapping airfoil using immersed boundary method

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The numerical simulation of flows past flapping foils at moderate Reynolds numbers presents two challenges to computational fluid dynamics: turbulent flows and moving boundaries. The direct forcing immersed boundary(IB) method has been developed to simulate laminar flows. However,its performance in simulating turbulent flows and transitional flows with moving boundaries has not been fully evaluated. In the present work,we use the IB method to simulate fully developed turbulent channel flows and transitional flows past a stationary/plunging SD7003 airfoil. To suppress the non-physical force oscillations in the plunging case,we use the smoothed discrete delta function for interpolation in the IB method. The results of the present work demonstrate that the IB method can be used to simulate turbulent flows and transitional flows with moving boundaries.

  19. Continuous maximum flow segmentation method for nanoparticle interaction analysis.

    Science.gov (United States)

    Marak, L; Tankyevych, O; Talbot, H

    2011-10-01

    In recent years, tomographic three-dimensional reconstruction approaches using electrons rather than X-rays have become popular. Such images produced with a transmission electron microscope make it possible to image nanometre-scale materials in three-dimensional. However, they are also noisy, limited in contrast and most often have a very poor resolution along the axis of the electron beam. The analysis of images stemming from such modalities, whether fully or semiautomated, is therefore more complicated. In particular, segmentation of objects is difficult. In this paper, we propose to use the continuous maximum flow segmentation method based on a globally optimal minimal surface model. The use of this fully automated segmentation and filtering procedure is illustrated on two different nanoparticle samples and provide comparisons with other classical segmentation methods. The main objectives are the measurement of the attraction rate of polystyrene beads to silica nanoparticle (for the first sample) and interaction of silica nanoparticles with large unilamellar liposomes (for the second sample). We also illustrate how precise measurements such as contact angles can be performed.

  20. PEMBELAJARAN MANDIRI APLIKASI ENTERPRISE RESOURCE SYSTEM: STUDI KASUS PADA APLIKASI SAP MODUL SALES AND DISTRIBUTION

    Directory of Open Access Journals (Sweden)

    Johan

    2013-11-01

    Full Text Available ERP (enterprise resource planning is a solution needed by companies to assist the integration of all functional areas. A self-learning media of ERP system is needed for the successful use which is highly depended on the users mastery. The learning media must be flexible to time and place. Therefore, this research creates a self-learning application for ERP system based on a case study on SAP application. SAP is an ERP-based solution widely used by medium to large companies. The method used are data collection, analysis on running business processes and the identification of information needs, followed by the application design. Identification of system requirements uses Flash CS5 Action Script 3.0. The result achieved in this research is a multimedia based learning tool which assists training for trainers and trainee and facilitates trainee supervision during training. The learning tool is found helpful in self learning process.

  1. Pembelajaran Mandiri Aplikasi Enterprise Resource System: Studi Kasus pada Aplikasi SAP – Modul Sales and Distribution

    Directory of Open Access Journals (Sweden)

    Johan Johan

    2013-12-01

    Full Text Available ERP (enterprise resource planning is a solution needed by companies to assist the integration of all functional areas. A self-learning media of ERP system is needed for the successful use which is highly depended on the users mastery. The learning media must be flexible to time and place. Therefore, this research creates a self-learning application for ERP system based on a case study on SAP application. SAP is an ERP-based solution widely used by medium to large companies. The method used are data collection, analysis on running business processes and the identification of information needs, followed by the application design. Identificationof system requirements uses Flash CS5 Action Script 3.0. The result achieved in this research is a multimediabased learning tool which assists training for trainers and trainee and facilitates trainee supervision during training. The learning tool is found helpful in self learning process.

  2. 49 CFR 40.299 - What is the SAP's role and what are the limits on a SAP's discretion in referring employees for...

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 1 2010-10-01 2010-10-01 false What is the SAP's role and what are the limits on a SAP's discretion in referring employees for education and treatment? 40.299 Section 40.299... TESTING PROGRAMS Substance Abuse Professionals and the Return-to-Duty Process § 40.299 What is the SAP's...

  3. Antioxidant activity test on ambonese banana stem sap (Musa parasidiaca var. sapientum

    Directory of Open Access Journals (Sweden)

    Hendrik Setia Budi

    2015-12-01

    Full Text Available Background: Polymorphonuclear cells (PMN release oxygen free radicals or reactive oxygen species (ROS during inflammation. As a result, ROS level is higher than antioxidant level in our body during oxidative stress leading to prolong inflammation or continuous tissue damage. Indonesia, on the other hand, is a country with various herbal medicines. For instance, ambonese banana (Musa parasidiaca var. sapientum is often used as herbal medicine. Ambonese banana, moreover, has flavonoid, polyphenol, tannin, and saponin as antioxidants to reduce free radicals by transferring their hydrogen atom. Medicine used to reduce the impact of free radicals is known as antioxidant. Antioxidant is proved to accelerate wound healing. Purpose: This research aims to analyze the effects of the antioxidant activity of Ambonese banana stem sap extract. Method: Antioxidant activities in this research were examined with 1,1-Diphenyl-2-picryl-hidrazyl (DPPH method by reacting with stable radical compounds. Spectrophotometry with a wavelength of 517 nm was used to measure absorption results shown in purple. The absorption results then were calculated by IC50 reduction activity. Result: There were significant differences of Ambonese banana stem sap antioxidant activity (p50%. Conclusion: Ambonese banana stem sap extract has antioxidant activities.

  4. Adaptive methods in computational fluid dynamics of chemically reacting flows

    Science.gov (United States)

    Rogg, B.

    1991-09-01

    Possible approaches to fully implicit adaptive algorithms suitable for the numerical simulation of unsteady two-dimensional reactive flows are examined. Emphasis is placed on self-adaptive gridding procedures applicable to time-dependent two-dimensional reactive flows. Pulsating flame propagation, autoignition in a nonpremixed flow, flame propagation in a strained mixing layer, and hot-spot-like self-ignition are considered as examples.

  5. COMPARISON OF METHODS FOR DETERMINING ENVIRONMENTAL FLOW IN SELECTED MOUNTAIN BASINS

    Directory of Open Access Journals (Sweden)

    Dariusz Młyński

    2015-10-01

    Full Text Available The paper describes the way of determining environmental flows, based on the use of Tennant and Tessman methods, a method based on flow duration curves, as well as instream flows using the methods of Kostrzewa. Calculations were conducted for the catchment of Młyniska River (cross-section Zakopane, which is located in upper Dunajec basin. Input data, obtained from the Institute of Meteorology and Water Management, National Research Institute in Warsawincluded observation series of daily flows for the years 2000–2014. The data were evaluated in terms of homogeneity and independence, using the Mann-Kendall-Sneyers. The calculations have shown differences between values of instream flow and environmental flow and also allowed us to conclude that the computed environmental flows were above the level determined by the absolutely low flow. Also conducted that disposable resources of water by Młyniska river, limited by instream flow and environmental flowdo not differ significantly.

  6. CyNC: A method for real time analysis of systems with cyclic data flows

    DEFF Research Database (Denmark)

    Jessen, Jan Jacob; Schiøler, Henrik; Nielsen, Jens Frederik Dalsgaard

    2006-01-01

    The paper addresses a novel method for performance analysis of distributed realtime systems with complex, and especially cyclic data flow graphs. The presented method is based on Network Calculus principles, where flow and service constraint functions are used to bound data flows and processing...

  7. Pigmentiphaga aceris sp. nov., isolated from tree sap.

    Science.gov (United States)

    Lee, Soon Dong

    2017-09-01

    Two Gram-stain-negative bacterial strains, SAP-32T and SAP-36, were isolated from sap drawn from the Acer pictum from Mount Halla in Jeju, Republic of Korea. The organisms were strictly aerobic, non-sporulating, motile rods and showed growth at 10-30 °C, pH 7-8 and with 0-2 % NaCl. The major isoprenoid quinone was Q-8. The predominant fatty acids were C16 : 0, cyclo-C17 : 0, summed feature 3 and C18 : 0. The polar lipids contained phosphatidylcholine, phosphatidylethanolamine, phosphatidylglycerol, an unknown aminophosphoglycolipid, an unknown glycolipid, an unknown phospholipid and two unknown lipids. The DNA G+C content was 64.4 mol%. The results of phylogenetic analyses based on 16S rRNA gene sequences indicated that SAP-32T and SAP-36 formed a distinct cluster with members of the genus Pigmentiphaga within the family Alcaligenaceae. Both strains showed 16S rRNA gene sequence similarity of 100 % to each other. The closest relatives of the isolates were Pigmentiphaga daeguensis (97.08 % sequence similarity), Pigmentiphaga kullae (97.01 %) and Pigmentiphaga litoralis (96.73 %). On the basis of data from phenotypic, chemotaxonomic and phylogenetic analyses, SAP-32T (=KCTC 52619T=DSM 104039T) and SAP-36 (=KCTC 52620=DSM 104072) represent members of a novel species of the genus Pigmentiphaga, for which the name Pigmentiphaga aceris sp. nov. is proposed.

  8. A Novel Putrescine Exporter SapBCDF of Escherichia coli.

    Science.gov (United States)

    Sugiyama, Yuta; Nakamura, Atsuo; Matsumoto, Mitsuharu; Kanbe, Ayaka; Sakanaka, Mikiyasu; Higashi, Kyohei; Igarashi, Kazuei; Katayama, Takane; Suzuki, Hideyuki; Kurihara, Shin

    2016-12-16

    Recent research has suggested that polyamines (putrescine, spermidine, and spermine) in the intestinal tract impact the health of animals either negatively or positively. The concentration of polyamines in the intestinal tract results from the balance of uptake and export of the intestinal bacteria. However, the mechanism of polyamine export from bacterial cells to the intestinal lumen is still unclear. In Escherichia coli, PotE was previously identified as a transporter responsible for putrescine excretion in an acidic growth environment. We observed putrescine concentration in the culture supernatant was increased from 0 to 50 μm during growth of E. coli under neutral conditions. Screening for the unidentified putrescine exporter was performed using a gene knock-out collection of E. coli, and deletion of sapBCDF significantly decreased putrescine levels in the culture supernatant. Complementation of the deletion mutant with the sapBCDF genes restored putrescine levels in the culture supernatant. Additionally, the ΔsapBCDF strain did not facilitate uptake of putrescine from the culture supernatant. Quantification of stable isotope-labeled putrescine derived from stable isotope-labeled arginine supplemented in the medium revealed that SapBCDF exported putrescine from E. coli cells to the culture supernatant. It was previously reported that SapABCDF of Salmonella enterica sv. typhimurium and Haemophilus influenzae conferred resistance toantimicrobial peptides; however, the E. coli ΔsapBCDF strain did not affect resistance to antimicrobial peptide LL-37. These results strongly suggest that the natural function of the SapBCDF proteins is the export of putrescine.

  9. Homotopy perturbation method for heat transfer flow of a third grade fluid between parallel plates

    Energy Technology Data Exchange (ETDEWEB)

    Siddiqui, A.M. [Pennsylvania State University, York Campus, York, PA 17403 (United States); Zeb, A. [COMSATS Institute of Information Technology, 30 H-8/1, Islamabad (Pakistan)], E-mail: amtaz56@yahoo.co.uk; Ghori, Q.K. [COMSATS Institute of Information Technology, 30 H-8/1, Islamabad (Pakistan); Benharbit, A.M. [Pennsylvania State University, York Campus, York, PA 17403 (United States)

    2008-04-15

    The present paper studies the heat transfer flow of a third grade fluid between two heated parallel plates for the constant viscosity model. Three flow problems, namely plane Couette flow, plane Poiseuille flow and plane Couette-Poiseuille flow have been considered. In each case the non-linear momentum equation and the energy equation have been solved using the homotopy perturbation method. Explicit analytical expressions for the velocity field and the temperature distribution have been derived.

  10. Axial and Centrifugal Compressor Mean Line Flow Analysis Method

    Science.gov (United States)

    Veres, Joseph P.

    2009-01-01

    This paper describes a method to estimate key aerodynamic parameters of single and multistage axial and centrifugal compressors. This mean-line compressor code COMDES provides the capability of sizing single and multistage compressors quickly during the conceptual design process. Based on the compressible fluid flow equations and the Euler equation, the code can estimate rotor inlet and exit blade angles when run in the design mode. The design point rotor efficiency and stator losses are inputs to the code, and are modeled at off design. When run in the off-design analysis mode, it can be used to generate performance maps based on simple models for losses due to rotor incidence and inlet guide vane reset angle. The code can provide an improved understanding of basic aerodynamic parameters such as diffusion factor, loading levels and incidence, when matching multistage compressor blade rows at design and at part-speed operation. Rotor loading levels and relative velocity ratio are correlated to the onset of compressor surge. NASA Stage 37 and the three-stage NASA 74-A axial compressors were analyzed and the results compared to test data. The code has been used to generate the performance map for the NASA 76-B three-stage axial compressor featuring variable geometry. The compressor stages were aerodynamically matched at off-design speeds by adjusting the variable inlet guide vane and variable stator geometry angles to control the rotor diffusion factor and incidence angles.

  11. An efficient method for DEM-based overland flow routing

    Science.gov (United States)

    Huang, Pin-Chun; Lee, Kwan Tun

    2013-05-01

    The digital elevation model (DEM) is frequently used to represent watershed topographic features based on a raster or a vector data format. It has been widely linked with flow routing equations for watershed runoff simulation. In this study, a recursive formulation was encoded into the conventional kinematic- and diffusion-wave routing algorithms to permit a larger time increment, despite the Courant-Friedrich-Lewy condition having been violated. To meet the requirement of recursive formulation, a novel routing sequence was developed to determine the cell-to-cell computational procedure for the DEM database. The routing sequence can be set either according to the grid elevation in descending order for the kinematic-wave routing or according to the water stage of the grid in descending order for the diffusion-wave routing. The recursive formulation for 1D runoff routing was first applied to a conceptual overland plane to demonstrate the precision of the formulation using an analytical solution for verification. The proposed novel routing sequence with the recursive formulation was then applied to two mountain watersheds for 2D runoff simulations. The results showed that the efficiency of the proposed method was significantly superior to that of the conventional algorithm, especially when applied to a steep watershed.

  12. CAPILLARY ELECTROPHORETIC ANALYSIS OF LOW-MOLECULAR-MASS OF CA SPECIES IN PHLOEM SAP OF Ricinus communis L.

    OpenAIRE

    Fitri, Noor; Thiele, Björn; Günther, Klaus; Buchari, Buchari

    2010-01-01

    A capillary electrophoretic (CE) analysis with ultra-violet (UV) detection was performed for further separation of low-molecular-mass (LMM) calcium species in phloem sap of Ricinus communis L. Two different background electrolytes (BGE) were used for the separation; these are (1) hydrogen phosphate/dihydrogen phosphate buffer containing cetyltrimethylammonium bromide (CTAB) as an electro-osmotic flow (EOF) modifier, and (2) boric acid buffer containing CTAB. Various parameters affecting the a...

  13. Continuous-Flow Biochips: Technology, Physical Design Methods and Testing

    DEFF Research Database (Denmark)

    Pop, Paul; Araci, Ismail Emre; Chakrabarty, Krishnendu

    2015-01-01

    This article is a tutorial on continuous-flow biochips where the basic building blocks are microchannels, and microvalves, and by combining them, more complex units such as mixers, switches, and multiplexers can be built. It also presents the state of the art in flow-based biochip technology...... and emerging research challenges in the areas of physical design and testing techniques....

  14. NONLINEAR PERTURBATION METHOD FOR CALCULATING AXISYMMETRIC CAVITATIONAL FLOWS

    Directory of Open Access Journals (Sweden)

    Vasyl Buivol

    2013-12-01

    Full Text Available A mathematical model of a cavity under the influence of perturbations of various origins is evaluated. The model is based on hydrodynamics of flows with free boundaries and the theory of small perturbations. Specific analysis is provided for cavitational flows behind cones

  15. An Immersed Boundary Method for Complex Flow and Heat Transfer

    NARCIS (Netherlands)

    Paravento, F.; Pourquie, M.J.; Boersma, B.J.

    2007-01-01

    The need to predict flow and heat transfer problems requires a flexible and fast tool able to simulate complex geometries without increasing the complexity of the flow solver architecture. Here we use a finite volume code that uses a direct solver with pressure correction. A new immersed boundary me

  16. Subgrid particle method for porous media and suspension flow

    NARCIS (Netherlands)

    Sman, van der R.G.M.; Brans, G.B.P.W.

    2008-01-01

    In this contribution we report on the initial steps in the development of a numerical scheme for flow through packed or suspended spheres. The spheres are semiresolved, meaning that their diameter is smaller than the grid spacing, but their excluded volume is taken into account. Flow in the fluid ph

  17. Subgrid particle method for porous media and suspension flow

    NARCIS (Netherlands)

    Sman, van der R.G.M.; Brans, G.B.P.W.

    2008-01-01

    In this contribution we report on the initial steps in the development of a numerical scheme for flow through packed or suspended spheres. The spheres are semiresolved, meaning that their diameter is smaller than the grid spacing, but their excluded volume is taken into account. Flow in the fluid

  18. A penalization method for calculating the flow beneath travelling water waves of large amplitude

    CERN Document Server

    Constantin, Adrian; Scherzer, Otmar

    2014-01-01

    A penalization method for a suitable reformulation of the governing equations as a constrained optimization problem provides accurate numerical simulations for large-amplitude travelling water waves in irrotational flows and in flows with constant vorticity.

  19. Distributed AC power flow method for AC and AC-DC hybrid ...

    African Journals Online (AJOL)

    DR OKE

    Hence the distribution power flow models to be developed were supposed to include both mesh and DG modeling (Sedghi ... Newton-Raphson based power flow methods, namely Newton ... Equation (1) is the mathematical realization of this ...

  20. A numerical method for a model of two-phase flow in a coupled free flow and porous media system

    KAUST Repository

    Chen, Jie

    2014-07-01

    In this article, we study two-phase fluid flow in coupled free flow and porous media regions. The model consists of coupled Cahn-Hilliard and Navier-Stokes equations in the free fluid region and the two-phase Darcy law in the porous medium region. We propose a Robin-Robin domain decomposition method for the coupled Navier-Stokes and Darcy system with the generalized Beavers-Joseph-Saffman condition on the interface between the free flow and the porous media regions. Numerical examples are presented to illustrate the effectiveness of this method. © 2014 Elsevier Inc.

  1. The experimental verification of a streamline curvature numerical analysis method applied to the flow through an axial flow fan

    Science.gov (United States)

    Pierzga, M. J.

    1981-01-01

    The experimental verification of an inviscid, incompressible through-flow analysis method is presented. The primary component of this method is an axisymmetric streamline curvature technique which is used to compute the hub-to-tip flow field of a given turbomachine. To analyze the flow field in the blade-to-blade plane of the machine, the potential flow solution of an infinite cascade of airfoils is also computed using a source model technique. To verify the accuracy of such an analysis method an extensive experimental verification investigation was conducted using an axial flow research fan. Detailed surveys of the blade-free regions of the machine along with intra-blade surveys using rotating pressure sensing probes and blade surface static pressure taps provide a one-to-one relationship between measured and predicted data. The results of this investigation indicate the ability of this inviscid analysis method to predict the design flow field of the axial flow fan test rotor to within a few percent of the measured values.

  2. Numerical study on modeling of liquid film flow under countercurrent flow limitation in volume of fluid method

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, Taro, E-mail: watanabe_t@qe.see.eng.osaka-u.ac.jp [Graduate School of Engineering, Osaka University, 2-1, Yamadaoka, Suita-shi, Osaka 565-7895 (Japan); Takata, Takashi, E-mail: takata.takashi@jaea.go.jp [Japan Atomic Energy Agency, 4002 Narita-chou, Oarai-machi, Higashi-Ibaraki-gun, Ibaraki 331-1393 (Japan); Yamaguchi, Akira, E-mail: yamaguchi@n.t.u-tokyo.ac.jp [Graduate School of Engineering, The University of Tokyo, 2-22 Shirakata-Shirane, Tokai-mura, Naka-gun, Ibaraki 319-1188 (Japan)

    2017-03-15

    Highlights: • Thin liquid film flow under CCFL was modeled and coupled with the VOF method. • The difference of the liquid flow rate in experiments of CCFL was evaluated. • The proposed VOF method can quantitatively predict CCFL with low computational cost. - Abstract: Countercurrent flow limitation (CCFL) in a heat transfer tube at a steam generator (SG) of pressurized water reactor (PWR) is one of the important issues on the core cooling under a loss of coolant accident (LOCA). In order to improve the prediction accuracy of the CCFL characteristics in numerical simulations using the volume of fluid (VOF) method with less computational cost, a thin liquid film flow in a countercurrent flow is modeled independently and is coupled with the VOF method. The CCFL characteristics is evaluated analytically in condition of a maximizing down-flow rate as a function of a void fraction or a liquid film thickness considering a critical thickness. Then, we have carried out numerical simulations of a countercurrent flow in a vertical tube so as to investigate the CCFL characteristics and compare them with the previous experimental results. As a result, it has been concluded that the effect of liquid film entrainment by upward gas flux will cause the difference in the experiments.

  3. An application of numerical methods to the prediction of strata methane flow in longwall mining

    OpenAIRE

    Ediz, I.G.

    1991-01-01

    This research describes an application of numerical methods for the prediction of strata methane flow into mine workings around a longwall coal face employing methane drainage. This method of methane prediction was developed by solving the time-dependent gas flow equation using the finite element analysis. Having obtained the gas pressure distribution throughout the finite element mesh, a mass flow equation was derived to calculate methane flow rate for a given mining boundary. A computer pro...

  4. Influences of environmental factors on the radial profile of sap flux density in Fagus crenata growing at different elevations in the Naeba Mountains, Japan.

    Science.gov (United States)

    Kubota, Mitsumasa; Tenhunen, John; Zimmerman, Reiner; Schmidt, Markus; Adiku, Samuel; Kakubari, Yoshitaka

    2005-05-01

    Sap flux density was measured continuously during the 1999 and 2000 growing seasons by the heat dissipation method in natural Fagus crenata Blume (Japanese beech) forests growing between 550 and 1600 m on the northern slope of the Kagura Peak of the Naeba Mountains, Japan. Sap flux density decreased radially toward the inner xylem and the decrease was best expressed in relation to the number of annual rings from the cambium, or in relation to the relative depth between the cambium and the trunk center, rather than as a function of absolute depth. The relative influences of radiation, vapor pressure deficit and soil water on sap flux density during the growing season were similar for the outer and inner xylem, and at all sites. Measurements of soil water content and water potential at a depth of 0.25 m demonstrated that sap flux density responded similarly and sensitively to water potential changes in this soil layer, despite large differences in rooting depth at different elevations, localizing one important control point in the functioning of this forest ecosystem. Identification of the relative influences of radiation, vapor pressure deficit and drying of the upper soil layer on sap flux density provides a framework for in-depth analysis of the control of transpiration in Japanese beech forests. In addition, the finding that the same general controls are operating on sap flux density despite climate gradients and large differences in overall forest stand structure will enhance understanding of water use by forests along elevation gradients.

  5. The Design Method of Axial Flow Runners Focusing on Axial Flow Velocity Uniformization and Its Application to an Ultra-Small Axial Flow Hydraulic Turbine

    Directory of Open Access Journals (Sweden)

    Yasuyuki Nishi

    2016-01-01

    Full Text Available We proposed a portable and ultra-small axial flow hydraulic turbine that can generate electric power comparatively easily using the low head of open channels such as existing pipe conduits or small rivers. In addition, we proposed a simple design method for axial flow runners in combination with the conventional one-dimensional design method and the design method of axial flow velocity uniformization, with the support of three-dimensional flow analysis. Applying our design method to the runner of an ultra-small axial flow hydraulic turbine, the performance and internal flow of the designed runner were investigated using CFD analysis and experiment (performance test and PIV measurement. As a result, the runners designed with our design method were significantly improved in turbine efficiency compared to the original runner. Specifically, in the experiment, a new design of the runner achieved a turbine efficiency of 0.768. This reason was that the axial component of absolute velocity of the new design of the runner was relatively uniform at the runner outlet in comparison with that of the original runner, and as a result, the negative rotational flow was improved. Thus, the validity of our design method has been verified.

  6. Auditoria fiscal previdenciária em ambiente SAP

    Directory of Open Access Journals (Sweden)

    Alexandre David Viva

    2006-12-01

    Full Text Available Este trabalho busca identificar meios para efetuar auditoria fiscal nos bancos de dados do SAP - o mais adotado ERP da atualidade (Bae e Ashcroft, 2004, 1 e 5; Khan, 2005, 5. Pretende-se concentrar no método de acesso às tabelas SAP, um dos cinco métodos de acesso aos bancos de dados de ERP (Neil Raden, 2004, 10. Em um primeiro momento, é necessário o levantamento, por empresa, de uma listagem dos cabeçalhos das tabelas com as quais ela trabalha, em bancos de dados que já alcançam os terabytes (SAP, SAP NetWeaver: 50. Como o SAP é um programa multilíngüe e multiempresarial, suas tabelas são criptografadas, isto é, os nomes das tabelas e de duas colunas não guardam a menor relação com os dados que elas registram (Saphir, 2004, 1. Em um segundo momento, então, por meio do ACL, a listagem de cabeçalhos de tabelas obtida é filtrada. As tabelas que interessam ao Fisco são solicitadas à empresa de uma forma mais precisa, de modo a não sobrecarregar nem a empresa nem do Fisco. Em um terceiro momento, ainda com auxílio do ACL, as tabelas especificadas são analisadas (Primeiros Passos, 2003, 3.

  7. Method of coupling 1-D unsaturated flow with 3-D saturated flow on large scale

    Directory of Open Access Journals (Sweden)

    Yan ZHU

    2011-12-01

    Full Text Available A coupled unsaturated-saturated water flow numerical model was developed. The water flow in the unsaturated zone is considered the one-dimensional vertical flow, which changes in the horizontal direction according to the groundwater table and the atmospheric boundary conditions. The groundwater flow is treated as the three-dimensional water flow. The recharge flux to groundwater from soil water is considered the bottom flux for the numerical simulation in the unsaturated zone, and the upper flux for the groundwater simulation. It connects and unites the two separated water flow systems. The soil water equation is solved based on the assumed groundwater table and the subsequent predicted recharge flux. Then, the groundwater equation is solved with the predicted recharge flux as the upper boundary condition. Iteration continues until the discrepancy between the assumed and calculated groundwater nodal heads have a certain accuracy. Illustrative examples with different water flow scenarios regarding the Dirichlet boundary condition, the Neumann boundary condition, the atmospheric boundary condition, and the source or sink term were calculated by the coupled model. The results are compared with those of other models, including Hydrus-1D, SWMS-2D, and FEFLOW, which demonstrate that the coupled model is effective and accurate and can significantly reduce the computational time for the large number of nodes in saturated-unsaturated water flow simulation.

  8. ADAPTIVE FINITE ELEMENT METHOD FOR HIGH-SPEED FLOW-STRUCTURE INTERACTION

    Institute of Scientific and Technical Information of China (English)

    Wiroj LIMTRAKARN; Pramote DECHAUMPHAI

    2004-01-01

    An adaptive finite element method for high-speed flow-structure interaction is presented. The cell-centered finite element method is combined with an adaptive meshing technique to solve the Navier-Stokes equations for high-speed compressible flow behavior. The energy equation and the quasi-static structural equations for aerodynamically heated structures are solved by applying the Galerkin finite element method. The finite element formulation and computational procedure are described. Interactions between the high-speed flow, structural heat transfer, and deformation are studied by two applications of Mach 10 flow over an inclined plate, and Mach 4 flow in a channel.

  9. Method and applications of fiber synthesis using laminar flow

    Science.gov (United States)

    Burns, Bradley Justin

    A Laminar Flow Reactor (LFR) using the principles of hydrodynamic focusing was created and used to fabricate functional composite polymer fibers. These fibers had the ability to conduct or serve as a carrier for singlet oxygen-generating molecules. Critical to the process was designing an easy-to-fabricate, inexpensive device and developing a repeatable method that made efficient use of the materials. The initial designs used a planar layout and hydrodynamically focused in only one dimension while later versions switched to a two-fluid concentric design. Modeling was undertaken and verified for the different device layouts. Three types of conductive particles were embedded in the formed polymer: silver, indium tin oxide (ITO) and polyaniline. The polymer was also used as a carrier to two singlet oxygen generating molecules: Methylene Blue (MB) and perylene. Both were effective in killing Bacillus thuringiensis but MB leached from the fiber into the tested cell suspension. Perylene, which is not water soluble, did not leach out and was just as effective as MB. Research that was performed at ITT is also presented. A critical need exists to detect, identify, quantify, locate, and track virus and toxin aerosols to provide early warning during both light and dark conditions. The solution presented is a remote sensing technology using seeding particles. Seeding particles developed during this program provide specific identification of threat cloud content. When introduced to the threat cloud the seeders will bind specifically to the analyte of interest and upon interrogation from a stand off laser source will fluoresce. The fluorescent signal is detected from a distance using a long-range microscope and collection optics that allow detection of low concentrations of threat aerosols.

  10. Base flow separation: A comparison of analytical and mass balance methods

    Science.gov (United States)

    Lott, Darline A.; Stewart, Mark T.

    2016-04-01

    Base flow is the ground water contribution to stream flow. Many activities, such as water resource management, calibrating hydrological and climate models, and studies of basin hydrology, require good estimates of base flow. The base flow component of stream flow is usually determined by separating a stream hydrograph into two components, base flow and runoff. Analytical methods, mathematical functions or algorithms used to calculate base flow directly from discharge, are the most widely used base flow separation methods and are often used without calibration to basin or gage-specific parameters other than basin area. In this study, six analytical methods are compared to a mass balance method, the conductivity mass-balance (CMB) method. The base flow index (BFI) values for 35 stream gages are obtained from each of the seven methods with each gage having at least two consecutive years of specific conductance data and 30 years of continuous discharge data. BFI is cumulative base flow divided by cumulative total discharge over the period of record of analysis. The BFI value is dimensionless, and always varies from 0 to 1. Areas of basins used in this study range from 27 km2 to 68,117 km2. BFI was first determined for the uncalibrated analytical methods. The parameters of each analytical method were then calibrated to produce BFI values as close to the CMB derived BFI values as possible. One of the methods, the power function (aQb + cQ) method, is inherently calibrated and was not recalibrated. The uncalibrated analytical methods have an average correlation coefficient of 0.43 when compared to CMB-derived values, and an average correlation coefficient of 0.93 when calibrated with the CMB method. Once calibrated, the analytical methods can closely reproduce the base flow values of a mass balance method. Therefore, it is recommended that analytical methods be calibrated against tracer or mass balance methods.

  11. SLAM family receptors and SAP adaptors in immunity.

    Science.gov (United States)

    Cannons, Jennifer L; Tangye, Stuart G; Schwartzberg, Pamela L

    2011-01-01

    The signaling lymphocyte activation molecule (SLAM)-associated protein, SAP, was first identified as the protein affected in most cases of X-linked lymphoproliferative (XLP) syndrome, a rare genetic disorder characterized by abnormal responses to Epstein-Barr virus infection, lymphoproliferative syndromes, and dysgammaglobulinemia. SAP consists almost entirely of a single SH2 protein domain that interacts with the cytoplasmic tail of SLAM and related receptors, including 2B4, Ly108, CD84, Ly9, and potentially CRACC. SLAM family members are now recognized as important immunomodulatory receptors with roles in cytotoxicity, humoral immunity, autoimmunity, cell survival, lymphocyte development, and cell adhesion. In this review, we cover recent findings on the roles of SLAM family receptors and the SAP family of adaptors, with a focus on their regulation of the pathways involved in the pathogenesis of XLP and other immune disorders.

  12. Non-contrast-enhanced MR hepatic arteriography with time-spatial labeling inversion pulses: comparison of imaging with flow-in and modified flow-out methods.

    Science.gov (United States)

    Isoda, Hiroyoshi; Furuta, Akihiro; Ohno, Tsuyoshi; Togashi, Kaori

    2017-07-01

    Background In non-contrast-enhanced magnetic resonance (MR) arteriography, the flow-out method using a selective tagging pulse with a long inversion time (TI) and a non-selective inversion recovery pulse with a short TI (the modified flow-out method) might further contribute to the suppression of background signal and facilitate improved visualization of the hepatic artery. However, no report has focused on the image quality of non-contrast-enhanced MR arteriography using the modified flow-out method. Purpose To compare the flow-in method with the modified flow-out method and to determine which method better visualizes the hepatic artery. Material and Methods Twenty-seven healthy volunteers were examined using respiratory-triggered three-dimensional true steady-state free-precession MR with two selective inversion recovery pulses (the flow-in method) or with one tagging pulse and one non-selective inversion recovery pulse (the modified flow-out method). Results Artery-to-liver contrast was significantly increased in the modified flow-out method relative to the flow-in method ( P contrast-enhanced MR arteriography using the modified flow-out method exhibited higher scores than with the flow-in method. With respect to overall image quality, the modified flow-out method was significantly better than the flow-in method ( P contrast-enhanced MR angiography is a promising technique for visualizing the hepatic artery.

  13. Experimental verification of color flow imaging based on wideband Doppler method.

    Science.gov (United States)

    Tanaka, Naohiko

    2014-01-01

    The purpose of this study is to eliminate the aliasing in color flow imaging. The wideband Doppler method is applied to generate a color flow image, and the validity of the method is experimentally confirmed. The single beam experiment is carried out to confirm the velocity estimation based on the wideband Doppler method. The echo data for the conventional pulsed Doppler method and the wideband Doppler method are obtained using a flow model, and the estimated velocity for each method is compared. The color flow images for each method are also generated using several types of flow model. The generated images are compared, and the characteristics of the imaging based on the wideband Doppler method are discussed. The high velocity beyond the Nyquist limit is successfully estimated by the wideband Doppler method, and the availability in low velocity estimation is also confirmed. The aliasing in color flow images is eliminated, and the generated images show the significance of the elimination of the aliasing in the flow imaging. The aliasing in color flow imaging can be eliminated by the wideband Doppler method. This technique is useful for the exact understanding of blood flow dynamics.

  14. Experimental verification of the streamline curvature numerical analysis method applied to the flow through an axial flow fan

    Science.gov (United States)

    Pierzga, M. J.

    1980-05-01

    To verify the results of a streamline curvature numerical analysis method, an investigation has been conducted in which comparisons are made between analytical and experimental data of an axial flow fan. Using loss model calculations to determine the proper outlet flow deviation angles, the flow field in the hub to tip plane of the turbomachine was calculated. These deviation angle calculations allow the inviscid streamline curvature (SLC) analysis to model a real fluid with viscous losses. The verification of this calculated flow field is the primary objective of the investigation; however, in addition to the hub to tip flow field, the numerical analysis of the blade-to-blade flow field was also investigated in some detail. To verify the accuracy of the numerical results, detailed flow surveys were conducted upstream and downstream of the test rotor of the axial flow fan. To obtain the necessary data to verify the blade-to-blade solution, internal blade row data were also collected. The internal blade row measurements were obtained by using a rotating circumferential traversing mechanism which was designed and implemented during this investigation. Along with these two sets of survey data, the static pressure distributions on the pressure and suction surfaces of the test rotor were also obtained.

  15. The study of slip line field and upper bound method based on associated flow and non-associated flow rules

    Institute of Scientific and Technical Information of China (English)

    Zheng Yingren; Deng Chujian; Wang Jinglin

    2010-01-01

    At present,associated flow rule of traditional plastic theory is adopted in the slip line field theory and upper bound method of geotechnical materials.So the stress characteristic line conforms to the velocity line.It is proved that geotechnical materials do not abide by the associated flow rule.It is impossible for the stress characteristic line to conform to the velocity line.Generalized plastic mechanics theoretically proved that plastic potential surface intersects the Mohr-Coulomb yield surface with an angle,so that the velocity line must be studied by non-associated flow rule.According to limit analysis theory,the theory of slip line field is put forward in this paper,and then the ultimate boating capacity of strip footing is obtained based on the associated flow rule and the non-associated flow rule individually.These two results are identical since the ultimate bearing capacity is independent of flow rule.On the contrary,the velocity fields of associated and non-associated flow rules are different which shows the velocity field based on the associated flow rule is incorrect.

  16. DOUBLE METHOD OF CHARACTERISTICS TO ANALYZE HYDRAULIC-THERMAL TRANSIENTS OF PIPELINE FLOW

    Institute of Scientific and Technical Information of China (English)

    邓松圣; 周明来; 蒲家宁

    2002-01-01

    The hydraulic and thermal transients in pipeline flow were studied. The method of characteristics for hydraulic transient analysis of batch transport of pipeline flow had been improved. The thermal transient equation, in which the term with v3 was involved, had been inferred, while the corresponding method of characteristics was constructed. The double method of characteristics, which can be used to study the coherent hydraulic-thermal transients of batch transport of pipeline flow, was developed.

  17. The CABARET method for a weakly compressible fluid flows in one- and two-dimensional implementations

    Science.gov (United States)

    Kulikov, Yu M.; Son, E. E.

    2016-11-01

    The CABARET method implementation for a weakly compressible fluid flow is in the focus of present paper. Testing both one-dimensional pressure balancing problem and a classical plane Poiseuille flow, we analyze this method in terms of discontinuity resolution, dispersion and dissipation. The method is proved to have an adequate convergence to an analytical solution for a velocity profile. We also show that a flow formation process represents a set of self-similar solutions under varying pressure differential and sound speed.

  18. Flow measurements in micro holes with electrochemical and optical methods

    Energy Technology Data Exchange (ETDEWEB)

    Zosel, J.; Guth, U.; Thies, A.; Reents, B

    2003-09-30

    The decreasing feature size of electronic compounds down to the micrometer range is paralleled by an increase in the aspect ratio, worsening all mass transport related processes. In this paper the conditions of liquid flow into micro holes and blind micro vias (BMV) with diameter of 100-300 {mu}m and depth between 100 {mu}m and 1.5 mm are investigated. The flow was induced by surface directed jet flows, visualised by microscopy aided particle image velocimetry ({mu}-PIV) and correlated with electrochemical mass transfer measurements using the ferro/ferri-hexacyanide redox couple. It was found that the mean flow velocity in the holes and the penetration depth in the blind holes are influenced especially by the roughness of the inner walls and, at a lower scale, by the velocity and the impinging angle of the jet. The results enable the estimation of the mean flow rate in through holes and the penetration depth in BMV at defined hydrodynamic conditions in the bath. This is one of the preconditions for the appropriate engineering of plating lines designed for micro structures.

  19. RECENT ADVANCES OF UPSCALING METHODS FOR THE SIMULATION OF FLOW TRANSPORT THROUGH HETEROGENEOUS POROUS MEDIA

    Institute of Scientific and Technical Information of China (English)

    Zhiming Chen

    2006-01-01

    We review some of our recent efforts in developing upscaling methods for simulating the flow transport through heterogeneous porous media. In particular, the steady flow transport through highly heterogeneous porous media driven by extraction wells and the flow transport through unsaturated porous media will be considered.

  20. Method and its application of the momentum model for debris flow risk zoning

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    In order to ascertain the distribution of flow depth and velocity of debris flow, the combination of numerical modeling and the GIS technology has been used to simulate the movement process of debris flow out of the outlet. The main model of momentum classification of risk zoning of debris flow is Z=Khv. Based on the distribution of the velocity and depth of debris flow, the distribution of momentum can be ascertained. Thereby the classification of risk zoning of debris flow can be worked out. A case study of Chacaito Valley in Caracas, Venezuela, is presented to illustrate the application of the method.

  1. Space-time discontinuous Galerkin finite element method for two-fluid flows

    NARCIS (Netherlands)

    Sollie, Warnerius Egbert Hendrikus

    2010-01-01

    The aim of this research project was to develop a discontinuous Galerkin method for two-fluid flows, which is accurate, versatile and can alleviate some of the problems commonly encountered with existing methods. A novel numerical method for two-fluid flow computations is presented, which combines t

  2. Comparative Statistical Study of Some SAP UI Technologies

    Science.gov (United States)

    Berdie, Adela; Osaci, Mihaela; Dan Lemle, Ludovic

    2011-09-01

    The goal of this paper is to present a comparative study on some web UI (User Interface) technologies that involve the creation of web applications on the platform SAP Net Weaver AS 7.01 of the integrated SAP (System Application Products) system. The attention will be directed mainly to the ABAP (Advanced Business Application Programing) development environment and to the Web Dynpro (WD) technologies, Floor Plan Manager (FPM) and Web Client UI. Through this study, we make an assesment regarding the decision of choosing a technology for the realisation of a project which consists of a web application.

  3. Managing the Technology Acquisition Integration Paradox at SAP

    DEFF Research Database (Denmark)

    Henningsson, Stefan; Kude, Thomas; Popp, Karl Michael

    2016-01-01

    In this paper, we report on a novel approach developed by SAP AG, the German enterprise software company, for managing the integration of acquisitions of companies to access innovative technologies and related capabilities: the Product Council approach. The value of the Product Council approach...... rests in ensuring critical speed while not compromising accuracy in the integration process. For SAP, the Product Council became a vital component in its technology acquisition capability that allows the company to retain its technological edge in the hypercompetitive software industry....

  4. Managing the Technology Acquisition Integration Paradox at SAP

    DEFF Research Database (Denmark)

    Henningsson, Stefan; Kude, Thomas; Popp, Karl Michael

    2016-01-01

    In this paper, we report on a novel approach developed by SAP AG, the German enterprise software company, for managing the integration of acquisitions of companies to access innovative technologies and related capabilities: the Product Council approach. The value of the Product Council approach...... rests in ensuring critical speed while not compromising accuracy in the integration process. For SAP, the Product Council became a vital component in its technology acquisition capability that allows the company to retain its technological edge in the hypercompetitive software industry....

  5. Numerical methods for simulating blood flow at macro, micro, and multi scales.

    Science.gov (United States)

    Imai, Yohsuke; Omori, Toshihiro; Shimogonya, Yuji; Yamaguchi, Takami; Ishikawa, Takuji

    2016-07-26

    In the past decade, numerical methods for the computational biomechanics of blood flow have progressed to overcome difficulties in diverse applications from cellular to organ scales. Such numerical methods may be classified by the type of computational mesh used for the fluid domain, into fixed mesh methods, moving mesh (boundary-fitted mesh) methods, and mesh-free methods. The type of computational mesh used is closely related to the characteristics of each method. We herein provide an overview of numerical methods recently used to simulate blood flow at macro and micro scales, with a focus on computational meshes. We also discuss recent progress in the multi-scale modeling of blood flow.

  6. Simulation of large incompressible flows by the finite element method

    Science.gov (United States)

    Bercovier, M.; Engelman, M.

    Super computers together with low cost 32 bit machines with graphics render more actual the challenge of designing a general purpose Fluid Dynamic code. Such an approach was the key to the introduction of computational structural mechanics into the design cycle. There FEM codes have replaced experiments and are evaluation tools at every stage. Except for a very limited domain (low Reynolds numbers for instance) this "black box" concept cannot be aplied in fluid mechanics. Nevertheless the success of the modular approach of FIDAP, the addition of new models and the extension of its pre and post-processing capabilities bring a new bridge between the fluid mechanics engineer and the design floor shop. It is now the task of the scientific community to design acceptable models in domains like turbulent flows,multiphase flows slightly compressible flows and so on. At the same time faster and robust algorithms for highly non linear problems must be devised.

  7. BLOCK ITERATIVE METHODS FOR LINEAR ALGEBRAIC EQUATION AND DOMAIN DECOMPOSITION METHOD FOR INCOMPRESSIBLE VISCOUS FLOW

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    It was proved numerically that the Domain Decomposition Method (DDM) with one layer overlapping grids is identical to the block iterative method of linear algebra equations. The results obtained using DDM could be in reasonable aggeement with the results of full-domain simulation. With the three dimensional solver developed by the authors, the flow field in a pipe was simulated using the full-domain DDM with one layer overlapping grids and with patched grids respectively. Both of the two cases led to the convergent solution. Further research shows the superiority of the DDM with one layer overlapping grids to the DDM with patched grids. A comparison between the numerical results obtained by the authors and the experimental results given by Enayet[3] shows that the numerical results are reasonable.

  8. Simple Radiowave-Based Method For Measuring Peripheral Blood Flow Project

    Science.gov (United States)

    Oliva-Buisson, Yvette J.

    2014-01-01

    Project objective is to design small radio frequency based flow probes for the measurement of blood flow velocity in peripheral arteries such as the femoral artery and middle cerebral artery. The result will be the technological capability to measure peripheral blood flow rates and flow changes during various environmental stressors such as microgravity without contact to the individual being monitored. This technology may also lead to an easier method of detecting venous gas emboli during extravehicular activities.

  9. Debris flow susceptibility mapping using a qualitative heuristic method and Flow-R along the Yukon Alaska Highway Corridor, Canada

    Science.gov (United States)

    Blais-Stevens, A.; Behnia, P.

    2016-02-01

    This research activity aimed at reducing risk to infrastructure, such as a proposed pipeline route roughly parallel to the Yukon Alaska Highway Corridor (YAHC), by filling geoscience knowledge gaps in geohazards. Hence, the Geological Survey of Canada compiled an inventory of landslides including debris flow deposits, which were subsequently used to validate two different debris flow susceptibility models. A qualitative heuristic debris flow susceptibility model was produced for the northern region of the YAHC, from Kluane Lake to the Alaska border, by integrating data layers with assigned weights and class ratings. These were slope angle, slope aspect, surficial geology, plan curvature, and proximity to drainage system. Validation of the model was carried out by calculating a success rate curve which revealed a good correlation with the susceptibility model and the debris flow deposit inventory compiled from air photos, high-resolution satellite imagery, and field verification. In addition, the quantitative Flow-R method was tested in order to define the potential source and debris flow susceptibility for the southern region of Kluane Lake, an area where documented debris flow events have blocked the highway in the past (e.g. 1988). Trial and error calculations were required for this method because there was not detailed information on the debris flows for the YAHC to allow us to define threshold values for some parameters when calculating source areas, spreading, and runout distance. Nevertheless, correlation with known documented events helped define these parameters and produce a map that captures most of the known events and displays debris flow susceptibility in other, usually smaller, steep channels that had not been previously documented.

  10. Adaptive Multiscale Finite Element Method for Subsurface Flow Simulation

    NARCIS (Netherlands)

    Van Esch, J.M.

    2010-01-01

    Natural geological formations generally show multiscale structural and functional heterogeneity evolving over many orders of magnitude in space and time. In subsurface hydrological simulations the geological model focuses on the structural hierarchy of physical sub units and the flow model addresses

  11. Energy efficient SDN commodity switch based practical flow forwarding method

    KAUST Repository

    AlGhadhban, Amer

    2016-07-04

    Recent SDN researches suffer from over-accumulation of unhealthy flow-load. Instead, we leverage the SDN controller network view to encode the end-to-end path information into the packet address. Our solution EncPath significantly reduces the flow-table size and the number of control messages. Consequently, the power consumption of network switches is in orders of magnitude less than other evaluated solutions. It also provides flow management flexibility and scalability. We compare EncPath with single and multipath routing solutions and single path solution. Also, we operated them in proactive and reactive modes. We find that EncPath flow entries in core switches in a multihomed fat-tree with 144 hosts is approximately 1000 times smaller than Equal-Cost MultiPath (ECMP) and random routing. Additionally, the number of control messages to setup the network is reduced by a factor of 200×. This, consequently, affords data-plane and control-plane devices space to process other tasks. © 2016 IEEE.

  12. Adaptive Multiscale Finite Element Method for Subsurface Flow Simulation

    NARCIS (Netherlands)

    Van Esch, J.M.

    2010-01-01

    Natural geological formations generally show multiscale structural and functional heterogeneity evolving over many orders of magnitude in space and time. In subsurface hydrological simulations the geological model focuses on the structural hierarchy of physical sub units and the flow model addresses

  13. 30 CFR 285.610 - What must I include in my SAP?

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What must I include in my SAP? 285.610 Section... Requirements Contents of the Site Assessment Plan § 285.610 What must I include in my SAP? Your SAP must... SAP, you must provide the following information: ER29AP09.115 (b) You must provide the results of...

  14. An empirical method for estimating travel times for wet volcanic mass flows

    Science.gov (United States)

    Pierson, Thomas C.

    1998-01-01

    Travel times for wet volcanic mass flows (debris avalanches and lahars) can be forecast as a function of distance from source when the approximate flow rate (peak discharge near the source) can be estimated beforehand. The near-source flow rate is primarily a function of initial flow volume, which should be possible to estimate to an order of magnitude on the basis of geologic, geomorphic, and hydrologic factors at a particular volcano. Least-squares best fits to plots of flow-front travel time as a function of distance from source provide predictive second-degree polynomial equations with high coefficients of determination for four broad size classes of flow based on near-source flow rate: extremely large flows (>1 000 000 m3/s), very large flows (10 000–1 000 000 m3/s), large flows (1000–10 000 m3/s), and moderate flows (100–1000 m3/s). A strong nonlinear correlation that exists between initial total flow volume and flow rate for "instantaneously" generated debris flows can be used to estimate near-source flow rates in advance. Differences in geomorphic controlling factors among different flows in the data sets have relatively little effect on the strong nonlinear correlations between travel time and distance from source. Differences in flow type may be important, especially for extremely large flows, but this could not be evaluated here. At a given distance away from a volcano, travel times can vary by approximately an order of magnitude depending on flow rate. The method can provide emergency-management officials a means for estimating time windows for evacuation of communities located in hazard zones downstream from potentially hazardous volcanoes.

  15. From Pore Scale to Turbulent Flow with the Unstructured Lattice Boltzmann Method

    DEFF Research Database (Denmark)

    Matin, Rastin

    Abstract: The lattice Boltzmann method is a class of methods in computational fluid dynamics for simulating fluid flow. Implementations on unstructured grids are particularly relevant for various engineering applications, where geometric flexibility or high resolution near a body or a wall...... is required. The main topic of this thesis is to further develop unstructured lattice Boltzmann methods for simulations of Newtonian fluid flow in three dimensions, in particular porous flow. Two methods are considered in this thesis based on the finite volume method and finite element method, respectively...

  16. Lattice Boltzmann methods for complex micro-flows: applicability and limitations for practical applications

    Science.gov (United States)

    Suga, K.

    2013-06-01

    The extensive evaluation studies of the lattice Boltzmann method for micro-scale flows (μ-flow LBM) by the author's group are summarized. For the two-dimensional test cases, force-driven Poiseuille flows, Couette flows, a combined nanochannel flow, and flows in a nanochannel with a square- or triangular cylinder are discussed. The three-dimensional (3D) test cases are nano-mesh flows and a flow between 3D bumpy walls. The reference data for the complex test flow geometries are from the molecular dynamics simulations of the Lennard-Jones fluid by the author's group. The focused flows are mainly in the slip and a part of the transitional flow regimes at Kn flow LBMs are the lattice Bhatnagar-Gross-Krook and the multiple-relaxation time LBMs with several boundary conditions and discrete velocity models. The effects of the discrete velocity models, the wall boundary conditions, the near-wall correction models of the molecular mean free path and the regularization process are discussed to confirm the applicability and the limitations of the μ-flow LBMs for complex flow geometries.

  17. Lattice Boltzmann methods for complex micro-flows: applicability and limitations for practical applications

    Energy Technology Data Exchange (ETDEWEB)

    Suga, K, E-mail: suga@me.osakafu-u.ac.jp [Department of Mechanical Engineering, Osaka Prefecture University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka 599-8531 (Japan)

    2013-06-15

    The extensive evaluation studies of the lattice Boltzmann method for micro-scale flows ({mu}-flow LBM) by the author's group are summarized. For the two-dimensional test cases, force-driven Poiseuille flows, Couette flows, a combined nanochannel flow, and flows in a nanochannel with a square- or triangular cylinder are discussed. The three-dimensional (3D) test cases are nano-mesh flows and a flow between 3D bumpy walls. The reference data for the complex test flow geometries are from the molecular dynamics simulations of the Lennard-Jones fluid by the author's group. The focused flows are mainly in the slip and a part of the transitional flow regimes at Kn < 1. The evaluated schemes of the {mu}-flow LBMs are the lattice Bhatnagar-Gross-Krook and the multiple-relaxation time LBMs with several boundary conditions and discrete velocity models. The effects of the discrete velocity models, the wall boundary conditions, the near-wall correction models of the molecular mean free path and the regularization process are discussed to confirm the applicability and the limitations of the {mu}-flow LBMs for complex flow geometries. (invited review)

  18. The influence of alkalinity of portland cement on the absorption characteristics of superabsorbent polymers (SAP) for use in internally cured concrete

    Science.gov (United States)

    Tabares Tamayo, Juan D.

    as the shape and size of the particles, were determined by optical microscopy combined with image analysis. The second stage, the absorption capacity of SAP's, involved determination of the swelling behavior and the absorption capacity of polymers exposed to artificial pore solutions with different levels of alkalinity. The swelling behavior was followed using the optical microscope while the absorption capacity was characterized using the tea bag method. It was found that changes in the chemical compositions of the pore solutions influence the adsorption kinetics and result in different absorption isotherms. In the third stage, the internal curing effects of inclusion of SAP in cement pastes were evaluated. Mixture proportions of pastes used in this stage of the study were selected based on the absorption capacity of the SAP determined in stage two. The testing of the pastes involved determination of their set times, heat of hydration, and autogenous shrinkage.

  19. Recent development of vortex method in incompressible viscous bluff body flows

    Institute of Scientific and Technical Information of China (English)

    LIU Lan; JI Feng; FAN Jian-ren; CEN Ke-fa

    2005-01-01

    Vortex methods have been alternative tools of finite element and finite difference methods for several decades. This paper presents a brief review of vortex method development in the last decades and introduces efficient vortex methods developed for high Reynolds number bluffbody flows and suitable for running on parallel computer architectures. Included in this study are particle strength exchange methods, core-spreading method, deterministic particle method and hybrid vortex methods. Combined with conservative methods, vortex methods can comprise the most available tools for simulations of three-dimensional complex bluff body flows at high Reynolds numbers.

  20. Loss of Heterozygosity at an Unlinked Genomic Locus Is Responsible for the Phenotype of a Candida albicans sapsapsap6Δ Mutant ▿

    OpenAIRE

    Dunkel, Nico; Morschhäuser, Joachim

    2011-01-01

    The diploid genome of the pathogenic yeast Candida albicans exhibits a high degree of heterozygosity. Genomic alterations that result in a loss of heterozygosity at specific loci may affect phenotypes and confer a selective advantage under certain conditions. Such genomic rearrangements can also occur during the construction of C. albicans mutants and remain undetected. The SAP2 gene on chromosome R encodes a secreted aspartic protease that is induced and required for growth of C. albicans wh...