Fiscal 1980 Sunshine Project research report. Development of hydrothermal power plant (Development of binary cycle power plant); 1980 nendo nessui riyo hatsuden plant no kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the fiscal 1980 research result on evaluation of elementary technology studies, research on plant technologies, and assessment of profitability for development of the next 10MW class large binary cycle power plant. In evaluation of heat media and heat cycles, selection of heat media and preparation of specimens through document survey, measurement of thermal characteristics, and preparation of pressure-enthalpy charts were carried out for selection of promising media. In evaluation of materials, as the field corrosion test and simulation results on 3 kinds of welding materials, it was concluded that SUS316 is best as material. In evaluation of heat medium turbine, through the test on oil film seal and mechanical seal techniques, various information were obtained. In evaluation of mist-cooling condenser, experiment on the basic unit heat exchanger, and study on the optimum design were carried out. In addition, research on plant technologies, and assessment of profitability were conducted. (NEDO)

Development of hot water utilizing power plant in fiscal 1999. Development of binary cycle power plant (Development of 10-MW class plant); 1999 nendo nessui riyo hatsuden plant to kaihatsu. Binary cycle hatsuden plant no kaihatsu (10MW kyu plant no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to utilize effectively middle to high temperature hot water type geothermal resources, R and D has been performed on a downhole pump-applied binary cycle power plant which exchanges heat energy with a secondary media in a heat exchanger, and generates electric power. This paper summarizes the achievements in fiscal 1999. This fiscal year has installed an operation control device and made partial modification therein for the hot water system testing device installed in the previous fiscal year, which was followed by test operation. Having been performed in addition were the installation of cooling water collection pumps, improvement of water storage tanks, modification of piping for injection of downhole pump cooling water, inspection of high-temperature cooling device and low-temperature cooling device, and discussions on deposits onto the downhole pumps. Furthermore, an environmental impact survey has performed measurements of precipitation, river flow rates, thermal spring, spring water, noise, and groundwater fluctuation. A survey was also carried out on transplantation of precious plants. In the single and overall test operation of the hot water system testing device, normal operation was identified. However, the operation had to be suspended because of a trouble in the downhole pump. (NEDO)

Fiscal 1997 development of the geothermal water use power plant, etc. Development of the binary cycle power plant (10MW class plant); 1997 nendo nessui riyo hatsuden plant nado kaihatsu. Binary cycle hatsuden plant no kaihatsu (10MW kyu plant no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A R and D was conducted with the aim of using medium-/high-temperature hot water type geothermal resources. In fiscal 1997, fabrication of geothermal water system testing equipment and geothermal water production/reduction piping installation work were conducted, and an environmental effect survey and ground water variation observation were carried out. Moreover, pumps to pump up geothermal water were fabricated. In the fabrication of a pump for No. 3 demonstration plant, the following improvements were made. Concerning the inlet undersea bearing, the shapes related to it were so reformed that external water feeding in the initial run can be done. Relating to the protection of the thrust bearing half load side friction face, a spring was added to the face so that it was structured to give preload. As a method to install a casing covering board, adopted was a band installation method which is easy in handling. The number of instrumentation cables was reduced. As to cables for downhole pumps, studied were methods of connection, etc. of connection portions of the motor connector and instrumentation cable. Moreover, purifying/regeneration facilities of the downhole pump bearing oil were fabricated and tested. 85 figs., 57 tabs.

Fiscal 1997 industrial technology R and D project. Research report on development of use technology of bio- resources such as complex biosystem (Development of use and production technologies of complex biosystems); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei riyo seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This project aims to establish production technology of functional substances, oil degradation and purification technology, and use technology of unused oil fraction through development of cultivation control technology of complex biosystems. For functional material production technology, as functional substances some specific marine bacteria inhibitors, antibreeding substances of microalgae, and UV absorption substances were isolated. The productivity of korormicin as specific inhibitor against marine bacteria was improved considerably by cultivation method. For research on molecular genetic analysis technology, a new identification technology and a simple automatic analysis system of microeucaryotes using genes were developed. For global environment purification technology such as efficient degradation of pollutants, study was made on cultivation control technology of phenol- degrading consortia, population dynamics of oil-degrading microbial consortia and a restoration method of oil pollution by complex biosystem at lower temperature, and the demonstration experiment of oil degradation were carried out. (NEDO)

Achievement report for fiscal 1997 on the development of technologies for utilizing biological resources such as complex biosystems. Development of technologies for producing substitute fuel for petroleum by utilizing organisms; 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Technologies of producing useful substances using the substance decomposing/producing functions of complex biosystems and methods of their handling are developed. In the utilization of microbes in the digestive tracts of termites and longicorns, it is made clear that several kinds of termites cleave the {beta}-O-4 ether linkage. In relation to technologies for wood decomposing complex microbial system construction and complex vector system development, a screening system is constructed in which strains that exhibit complex actions are combined. Concerning the advanced utilization of tropical oil plants, conditions are determined for inducing callus out of oil palm tissues. Out of oil palm sarcocarp tissues, mRNA (messenger ribonucleic acid) is isolated for the construction of a cDNA (complementary deoxyribonucleic acid) library. For the purpose of isolating a powerful promoter, a partial base sequence is determined for ubiquitin that frequently expresses itself in cells. A pathogenic bacterium ailing the oil palm is sampled for identification, and it is inferred that the bacterium is a kind of Ganoderma boninense. (NEDO)

FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the petroleum substituting fuel production technology using biology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made. As a part of the study, the establishment was aimed at of the high-grade utilization technology of seaweed/algae using the degradation/conversion functions of the consortium base and the useful substance production technology by interaction of the consortium base of organism and flora/fauna. Studies for the establishment of the technology were made in the following two fields: technology to use unused resources such as lignocellulose and technology to produce petroleum substituting useful resources. As to the technology to use unused resources, the establishment was proceeded with of the technology to degrade/convert the seaweed-origin acidic polysaccharide into the useful substance using the consortium system. In FY 1998, in search of the excellent microorganism consortia which can degrade/solubilize carageenan, samples were picked up from the underwater of the Republic of Palau and incubated in the flat culture medium. Thirty-eight kinds of the degraded bacterium group were acquired. Using the degraded bacterium group, {kappa}-carrageenan was degraded and analyzed of the products. (NEDO)

FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the petroleum substituting fuel production technology using biology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made. As a part of the study, the establishment was aimed at of the high-grade utilization technology of seaweed/algae using the degradation/conversion functions of the consortium base and the useful substance production technology by interaction of the consortium base of organism and flora/fauna. Studies for the establishment of the technology were made in the following two fields: technology to use unused resources such as lignocellulose and technology to produce petroleum substituting useful resources. As to the technology to use unused resources, the establishment was proceeded with of the technology to degrade/convert the seaweed-origin acidic polysaccharide into the useful substance using the consortium system. In FY 1998, in search of the excellent microorganism consortia which can degrade/solubilize carageenan, samples were picked up from the underwater of the Republic of Palau and incubated in the flat culture medium. Thirty-eight kinds of the degraded bacterium group were acquired. Using the degraded bacterium group, {kappa}-carrageenan was degraded and analyzed of the products. (NEDO)

Development of acoustic partial discharge detection device; Bubun hoden kenshutsusochi wo riyo shita onkyo niyoru hendensetsubi no zetsuen rekka shindan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Suenaga, Kiyoka [Kawasaki Steel Corp., Tokyo (Japan)

1999-06-15

This paper introduces an acoustic partial discharge detection device, consisting of a microphone, amplifier circuit for analog signals, A/D (Digital Signal Processor). This device has the following unique characteristics: (1) Judging whether or not there is partial discharge by analyzing supersonic signals. (2) High sensitivity for detecting discharge ; 100 pC from a distance of 1.2 m. (3)Locating the position of discharge occurrence by using a sharpe directional parabola microphone and laser beam pointer. The detector was used in the steel works to detect partial discharge on high-voltage electrical apparatus, where faults due to partial discharge were found in the potential transformer and current transformer. The effectiveness of the device was thus verified. (author)

Survey report on the development/utilization of petroleum substitution energy in the Pacific region; Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper collected/analyzed data on petroleum substitution energy in the Pacific region. In fiscal 1996, in addition to collection of the existing energy data, conducted were collection of energy data made retroactive from 1971, and time-series collection of the energy related expanded data including energy related production statistics/social statistics, energy consumption amount by industry, power generation facilities, oil production facilities, and environmental data. As to petroleum substitution energy, the paper took up new energy such as hydroelectric, nuclear, geothermal, photovoltaic, and wind power generation, and commercial-base renewable energy. As a result of the analysis, the supply of petroleum substitution energy in the whole Pacific region has been stable, 6.6% during 1980-1990, 7.4% in the first half of the 1990s, largely over the primary energy supply. The supply of nuclear power was overwhelmingly large, followed by hydroelectric energy and geothermal/new energy. 15 figs., 23 tabs.

Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

Fiscal 1998 R and D project on industrial technology. Development report on use technology of bioresources such as bioconsortia (Development of analysis technology of bioconsortia); 1998 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For use of advanced functions of bioconsortia (complex microorganisms composed of more than 2 microorganisms with certain specific function), this project analyzes specific functions of specific organisms and the interaction between the specific functions, and develops isolation and incubation technologies of component organisms. In fiscal 1998, to promote this project, the meetings were held frequently in National Institute of Bioscience and human Technology. Study was made on production of useful substances and useful degradation functions in association with bioconsortia. The result showed that microorganisms coexisting with nematode produced physiologically active substances exhibiting antimicrobial activities to tubercle bacillus, MRSA and others, microorganisms coexisting in eggs of some insects produced substances having antiviral activities and activities against pathogenic bacteria in a plant, and microorganisms growing in some plants or mycorrhiza organisms produced insecticidal substances or growing-promoting substance. The basic understanding was obtained on cooperative actions of bioconsortia to bioremediation and degradation of organic substances. (NEDO)

Development of hot water utilizing power plant in fiscal 1998. Development of a binary cycle power generation plant (development of a 10-MW class plant); 1998 nendo nessui riyo hatsuden plant nado kaihatsu. Binary cycle hatsuden plant no kaihatsu (10MW kyu plant no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This paper summarizes the achievements in fiscal 1998 on developing a 10-MW geothermal power plant in the Hohi-Sugawara area being a representative area of middle-to-high temperature hot water resources. In designing the plant, domestic and overseas surveys were carried out on media suitable for binary cycle power plants, thermal cycle characteristics, construction cost, environmental effects, safety, operation, maintenance and control. Latest technologies were also surveyed and analyzed. The plant construction performed development construction around the testing devices, new construction of a plant control room building, constructions for installing electrical machines including the hot water system testing devices, river water intake facility construction, and cooling water intake facility installing construction. The environmental effect investigation included investigations on rain falls, river flow rates, hot springs, spring water, monitoring during the construction, and the state of transplantation of precious plants, and observation on groundwater variation. In verifying the geothermal water pumping system, factory tests were carried out on DHP3 demonstration machine which couples the pump section of a down-hole pump with the motor section, whose performance and functions were verified. (NEDO)

FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of establishing the high-grade utilization technology of unused seaweed/algae and production technology of useful substances using high-grade functions of bioconsortia, study was conducted, and the FY 1999 results were reported. In the analysis of the ocean environment adaptation mechanism, the R and D were made of a selection method of the marine microbial consortia using korormicin. In the study of the high-grade utilization technology of unused resources/substances such as marine-producing algae, several tens of the carrageenase producing microbial consortia were acquired from the surface of seaweed, and some carrageenase producing bacteria and non-producing bacteria were acquired by isolating as pure strains. In the study of the petroleum substituting useful resource production technology, developed was a monitoring system of the environmental stress using marine-product invertebrate/micro-algae symbiotic system. In the study of the high-grade utilization of large useful algae, elucidation of the related genes, fabrication of variants and analysis of genes were carried out for the bacterium BUP-7 which indicates activity of growth acceleration/shape formation of seaweed. (NEDO)

FY 1999 report on the results of the project on the industrial science technology R and D. R and D of complex carbonhydrate production/utilization technology (Development of CO2 fixation/effective utilization technology by applying complex carbonhydrate); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo. Fukugo toushitsu seisan riyo gijutsu no kenkyu kaihatsu (Fukugo toushitsu oyo nisankatanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of making an industrial use of complex carbonhydrate performing an important function in substance recognition, etc., which cannot be realized by only nucleic acid, protein and lipid, the R and D of the basic technology related to the production/utilization were conducted, and the FY 1999 results were reported. In the study of synthesis/utilization/remodeling technology of complex carbonhydrate using the chemical synthesis method, the R and D were made not only on the synthesis of sugar chain but for the synthesis method of the peptide added with sugar chain, that is, glycopeptide. Further, as to the reaction with the aim of the application, there was hope for large-quantity synthesis of milk oligosaccharide by the oxygen method. In the study of the design technology of complex carbonhydrate molecules, the systematical analysis using the model glycopeptide was conducted of effects of the sugar chain addition part and sugar chain structure on the 3D structure and physiological activity. Concerning the synthesis/utilization/remodeling technology of complex carbonhydrate using the biological method, study was made of the animal cell utilization, microorganism utilization, technology of structural analysis of complex carbonhydrate, etc. (NEDO)

FY 1999 report on the results of the project on the industrial science technology R and D. Development of utilization technology of biological resources such as bioconsortium system (Development of the petroleum substituting fuel production technology using living organisms); 1999 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugou seibutsukei tou seibutsu shigen riyo gijutsu kaihatsu (Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of developing the technology for producing and degrading useful substances using bioconsortia, study was made of the handling technology of bioconsortia, the basic element technology, etc., and the FY 1999 results were reported. In the study of the high-grade utilization technology of lignocellulose/the components, an sample was obtained in which the effect of the bacteria culture supernatant treatment was recognized in the biobleaching by co-treatment of the bacteria culture filtrate - MnP. As to the search for control factor of lignin degrading enzyme and the utilization technology, it was found out that bisphenol A was efficiently degraded by a combination of laccase and mediator production bacteria. Concerning the utilization technology of plant symbiotic bacteria, classification/identification have been finished of approximately 60% of the stored bacteria. In the study of the production technology of the petroleum substituting useful resource, a system was constructed in which immature embryos were used for callus induction and regeneration of plantlets, and plants were regenerated at high frequency via the formation of adventitious embryos. By this, the culture cell with high propagation ability was obtained. (NEDO)

Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the technology to fix and effectively use carbon dioxide using bacteria and microalgae (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo))

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of contributing to the solution to the global environmental problem, a technology is developed in which by searching for/breeding/developing bacteria, etc. which conduct photosynthesis highly effectively, CO2 is fixed and recycled. The fiscal 1996 R and D is outlined as the utilization of bacteria, microalgae, etc. Obtained were microalgae exceeding the conventional strains in CO2 fixation ability, and bacteria/microalgae excellent in production of polysaccharides, hydrocarbon, lipid, biological active substances, etc. The fundamental study was continued of CO2 integrated enzyme function/reaction system as molecular biological breeding. In the cell fusion, a set-up of conditions for green algae was started. For the confirmation of performance of high dense/quantity culture technology using solar light, further improvement of performance and systematization, 200L scale testing equipment was manufactured. It is a collective reactor and enabled study of ventilation/agitation and control of light strength. A reactor analysis model was constructed. Also including the conversion into useful substances, energy/material balance was systematically studied. Collection of technical literature and information exchanges were made in Japan and overseas. 276 refs., 475 figs., 156 tabs.

FY 1995 report on verification of geothermal exploration technology. Development of fracture reservoir exploration technology (development of seismic exploration); 1995 nendo chinetsu tansa gijutsunado kensho chosa. Danretsugata choryuso tansaho kaihatsu (danseiha riyo tansaho kaihatsu) hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This report provides the development of new exploration technology using elastic waves, such as reflection seismic survey, VSP, and seismic tomography, for precisely characterizing subsurface fractures in geothermal reservoirs. In order to investigate and improve the effective data acquisition and analysis methods for detecting a fault type of fractures, an experiment of a seismic tomography method was conducted using wells drilled in the Ogiri geothermal field, Aira-gun, Kagoshima Prefecture. An experiment of propagation characteristics of piezo type underground seismic source in the volcanic field was also conducted as a trend survey of underground seismic sources. The fracture type in the model field was systematically analyzed by measuring the core samples obtained in the demonstration test field through remanence measurement, fluid inclusion measurement, and zircon measurement using test equipment, and by analyzing results obtained from cores and results of seismic tomography obtained from the wells. Based on these results, the effectiveness and practical application of exploration methods using elastic waves were investigated. 80 refs., 250 figs., 49 tabs.

Evaluation report on research and development of 'seawater purification and byproduct utilization'; 'Kaisui Tansuika to fukusanbutsu riyo' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-03-01

Research, development, and evaluation were made on seawater purification for the purpose of supplying inexpensive city water stably in the future. In the research of the high flow rate long-tube type multi-stage flash process, basic characteristics were identified by studying fluidity, heat transfer, deaeration, and decarburization by using a test plant with a capacity of 3,000 m{sup 3}/d. A number of findings were derived in carrying out demonstration studies by using a test module with a capacity of 100,000 m{sup 3}/d. Research on heat transfer pipe materials covered a wide area including copper alloys, titanium and aluminum alloys, and ferrous materials, where a prospect was obtained on materials which may be practically usable in the future as transfer pipes in large seawater purifying equipment. Research on a concrete evaporator body proved that it is more economical than steel evaporators, and has sufficient corrosion resistance even against high-temperature brine. Other activities included researches on effects of contaminated seawater, brine diffusion, byproduct utilization, and total systems. Social and economic evaluations were also performed. (NEDO)

FY 2000 report on the development of hydrothermal use power plant, etc. Development of the binary cycle power plant (Development of a 10MW class plant); 2000 nendo Nessui riyo hatsuden plant tou kaihatsu. Bainari cycle hatsuden plant no kaihatsu - 10MW kyu plant no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-01-01

For the purpose of developing a 10MW class demonstrative plant for geothermal binary power generation, the R and D were carried out, and the results obtained from FY 1995 to FY 1999 were summed up. In the interim evaluation made in July 1994, study was to be phasedly proceeded with for the main three systems (hydrothermal system, medium system and power generation system) which compose the 10MW class binary cycle power plant. The test on the hydrothermal system was started in FY 1995. In the R and D, the following were conducted for evaluation: design/manufacture/installation of the test device for the hydrothermal system, manufacture of demonstrative downhole pump (DHP) No.3 and test at plant, test on the hydrothermal system. As to the turbine working medium suitable for binary power plant, the specified freon/substitute freon have been used, but it seems that hydrocarbons such as butane and pentane can be effective in future. In the study of the economical efficiency, it was pointed out that for the commercialization, it is important to improve durability of DHP and further reduce the cost of DHP equipment and cost of repairs. (NEDO)

Development of deepsea geomagnetic and electric fields observation system using submarine cables. 2; Kaitei cable riyo no shinkai chijiki denba kansoku station no kaihatsu. 2

Energy Technology Data Exchange (ETDEWEB)

Miyazaki, T; Nakatsuka, T; Murakami, Y [Geological Survey of Japan, Tsukuba (Japan); Onishi, N

1997-10-22

VENUS Project aims at constructing a deepsea geomagnetic and electric fields observation station to cover the Ryukyu Trench, Philippine Sea, and Mariana Trough, by the reuse of the Okinawa-Guam commercial marine communication cable now out of service. This report deals with a scenario for the development of a geomagnetic/electric observation system as a part of the planned long-term sea bottom observation effort and the installation of equipment therefor. The first stage consists of the towing of a frame mounted with the system equipment and a cable to connect to a data transmission relay and their placement at a specified location on the sea bottom. The cable is extended toward the relay and its leading end is allowed to land near the relay. Next, a manned submersible vessel is used to connect the cable end to the relay, the submersible vessel is next driven along the connection cable toward the system equipment for the determination of the position and orientation of the system equipment, and then electrodes are arrayed at an interval of 20m into an L-letter configuration. The system will be established in March, 1998, on the 4200m-deep continental slope of the Ryukyu Trench approximately 90km southeast of Okinawa. 2 figs., 1 tab.

International research cooperation project. Assessment report on the R and D of the comprehensive development/utilization technology of energy of gas hydrate resource; Gas hydrate shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As to 'the R and D of the comprehensive development/utilization technology of gas hydrate resource,' assessment was conducted and reported from an aspect of the third party. This R and D is a timely project being aimed at establishing the basic technology on gas hydrate from both aspects of fundamental research and practical research. In the development of gas hydrate resource in the tundra zone, the development of measuring methods for thermal conductivity and dielectric constants advanced the establishment of a guide for exploration and possibilities of assessment of the resource amount. In the development/production, it can be said that the knowledge/information collected by exchanging methane in gas hydrate with CO2 means no needs for new supply of heat and also contributes to the isolation of CO2. As to the utilization technology, the results were rated very high also internationally of tackling the quantitative evaluation method at molecular levels of the gas included in hydrate using Raman spectroscopy to establish the industrial gas separation method using the low-temperature environment in the tundra zone. (NEDO)

FY 1997 report on the results of the industrial technology R and D project. Development of technology to use biological resources such as the complex biological system (Development of biological use petroleum substitution fuel production technology); 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Seibutsu riyo sekiyu daitai nenryo seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Experimental researches were conducted and the FY 1997 results were reported with the aim of establishing analytical technology for the complex biological system by which the complex biological system can be analyzed in such a state as it is using the molecular biological method. In the study of the molecular genetic analytical technology, PCR primers used for amplification of topoisomerase II genes of the whole eukaryote was designed. As to the histochemical analytical technology, a study was made on the new constitution microorganism detection method by the hybridization method and the antibody specific dyeing method, and the following were conducted: manifestation in quantity of colibacillus and the recovery, refining, and construction of peptide library by fuzzy display method. Concerning the functional analytical technology, technological researches were made such as the environmental adaptation mechanism of high thermophile and the information transfer mechanism among bacteria through cell membranes for elucidation of the special environment detection/response mechanism and the special environment adaptation/resistance mechanism. As to the separation/culture technology, various anaerobic microorganisms were separated from marine sponge for the development of a method of culturing in 3D matrices. (NEDO)

Research and development of basic technologies for the next generation industries, 'recombinant DNA utilizing technology'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'kumikae DNA riyo gijutsu'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to the recombinant DNA utilizing technology to create new microorganisms for processes in the chemical industry. The major achievements of the present research and development include establishment of the P450 gene manifestation system attributed from microsomes and mitochondria, and the success of the world's first simultaneous manifestation of P450 and reduction enzyme. Furthermore, the fused enzyme combining P450 and the reduction enzyme genetically was successfully manufactured ahead of the other countries, opening the way to industrializing the recombinant enzymes for use in bio-processes in the chemical industry. In creating a high-efficiency secretion recombinant bacillus subtilis stock, a bacillus subtilis host whose protease activity has been noticeably decreased was created. As an achievement of the research on the 'basic recombinant DNA technology', high-efficiency manifestation vector of medium level thermophile was created, and its usefulness was demonstrated. In addition, a host and vector system for high level thermophile was developed for the first time in the world. These achievements have opened the way to industrial utilization of the thermophilic bacteria. (NEDO)

Evaluation report on research and development of 'the comprehensive water recycling and utilization systems'; 'Mizu sogo saisei riyo system' no kenkyu kaihatsu ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-08-01

This research and development project is aimed at treatment of sewage, industrial waste water and the like at lower cost for reutilization, while efficiently producing methane or the like by the systems annexed to the water treatment systems with high-concentration bio-reactor systems incorporating separation membranes. The waste water types studied to be treated by these systems include sewage discharged in large quantities and waste water containing oil/fat and protein (low-concentration waste water), and starch-, alcohol and paper/pulp-containing waste water, and excrements (medium-concentration waste water). The project has found the optimum systems, by adequately configuring the separation membrane modules, and combining dissolution of suspended solid with methane fermentation reactors for selective treatment of organic substances; improved efficiencies of removing organic substances and producing methane by fermentation, and realized reduction in quantities of discharged sludge; and thereby established the bases for the new waste water treatment techniques. The reactor systems developed for water treatment are those based on biological removal of nitrogen. They greatly reduce treatment time to produce treated water of high quality. For treatment of sludge, the techniques have been developed to convert sludge into oil. These results are well applicable to various areas, e.g., sewage treatment, and food and pulp industries. (NEDO)

Fiscal 2000 achievement report. Research and development of low-pollution brown coal utilization technology; 2000 nendo seika hokokusho. Kattan no teikogai riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Studies were made for developing low-pollution easy-to-operate industrial furnaces for use in small and medium size plants in Indonesia. In this fiscal year, two kinds were selected out of Indonesia yielded brown coals, which were then subjected to test combustion in a bench scale fluidized bed combustor for examination for their combustion characteristics and environmental impact generating characteristics. The nitrogen oxides from the brown coals were found to mark approximately 100 ppm at an excess air ratio of 1.4, which was higher than in the case of bituminous coal. The NOx concentration level was found to be lower in the circulation fluidized bed boiler than in the spreader stoker fired boiler. Combustion efficiency exceeding 98% was achieved. A survey was conducted of brown coal users in various industrial fields in Indonesia. It was then concluded that the tested method not be recommended for use in small businesses in the textile industry because there would be no economic profit or improved efficiency for them but that it would be feasible in the plantation industry where the fluidized bed combustion/heat exchanger aided indirect process and the use of electrical dust precipitators would protect products from contamination. (NEDO)

WE-NET. Substask 4. Development of hydrogen production technologies; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 4. Suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Under the hydrogen-utilizing international clean energy system technology project WE-NET (World Energy NET Work), researches were conducted aiming at the establishment of a hydrogen production technology through electrolysis of polymer electrolyte solution. In fiscal 1998, element technologies were developed for the development of high-efficiency/large-capacity water electrolyzing plants using electrodeless deposition and hot pressing, research and investigation of optimum operating conditions were conducted, and a service plant conceptual design and a polymer electrolytic membrane were developed. In addition, literature was searched for the current state of ion exchange membranes and water electrolysis, both indispensable for the hydrogen production technology discussed in this paper. In the field of lamination of large cells (electrode surface:2500cm{sup 2}), an excellent energy efficiency level exceeding 90% set as the target for a large laminated cell performance test was achieved - 92.6% by electrodeless deposition and 94.4% by hot pressing. As for polymer membranes capable of resisting high temperatures, a membrane with an ionic conductivity of 0.066S/cm at 200 degrees C was newly developed. (NEDO)

Research and development of technologies for CO{sub 2} fixation and effective utilization thereof, etc., in fiscal 1998. Report on research and development of technologies for the effective use of CO{sub 2} by virtue of contact hydrogenation (CO{sub 2} separation and recovery system of the next-generation type); 1998 nendo nisanka tanso koteika yuko riyo gijutsu nado kenkyu kaihatsu jigyo. Sesshoku suisoka hanno riyo nisanka tanso yuko riyo gijutsu kenkyu kaihatsu jigyo kenkyu kaihatsu jigyo (jisedaigata shoene CO{sub 2} bunri kaishu system ni kansuru chosa kenkyu hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Researches were conducted for the goal of proposing a totally new process enhanced in efficiency and energy saving, and capable of CO2 separation. In fiscal 1997, hydrocarbon materials were reformed by oxygen separated within a system allowing fuel cells to generate power efficiently, when all the emitted CO2 was separated and recovered within the system. Furthermore, cold heat was utilized for the acquisition of liquefied CO2 gas products. A part of oxygen separated at the fuel cell cathode was recycled into the combustion section external to the tubular reaction reformer, and CO2 was separated by mere cooling from the combustion products for the simultaneous production of by-products such as high-purity nitrogen gas and liquefied CO2 for a great improvement in economy. In fiscal 1998, the system was improved. Proposed then was a new system in which an oxygen partial oxidation type reformer assumed the nuclear role, separating all the oxygen at the cathode, reusing part thereof for oxygen enrichment, and feeding the rest thereof into the reformer. The design realized the recycling of the whole of the products of the two cell electrodes into the reformer for the maximum reuse of the products of the hydrogen/oxygen separation function. (NEDO)

Fiscal 1981 Sunshine Project research report. Development of hydrothermal power plant. Development of binary cycle power plant. Conceptual plant design; 1981 nendo nessui riyo hatsuden plant no kaihatsu / binary cycle hatsuden plant no kaihatsu seika hokokusho . Plant gainen sekkei

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Conceptual design was made on a 10MW class binary cycle power plant for a demonstration plant superior in reliability and profitability, under most realistic current geothermal field conditions. In the design, study was made on heat balance, main pipe system, equipment allocation, and electric system for a plant system configuration, and study was also made on preheater, evaporator, condenser, turbine and others for plant component equipment. Further study was made on optimization of mist cooling condenser, instrumentation, control, utility, and environmental measures. The following basic data were obtained through the conceptual design: plant inlet hot water temperature: 130 degrees C, plant outlet hot water temperature: 70 degrees C, hot water flow rate: 1,415t/h, working fluid: R-114, R-114 pressure in evaporator: 11.98kg/cm{sup 2} abs, R-114 evaporation temperature: 91.1 degrees C, R-114 condensation temperature: 31.0 degrees C, R- 114 flow rate: 2,265t/h, site area: 106.5m x 102.4m, building area: 48.7m x 16.8m, and building height: 13.0m. (NEDO)

Fiscal 1994 entrusted task report. Surveys of advanced natural gas development and efficient utilization (Survey of coal hydrogasification technology development); 1994 nendo tennen gas kodo kaihatsu yuko riyo chosa tou itaku gyomu hokokusho. Sekitan suiten gaska gijutsu kaihatsu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

For the establishment of a practical process for substitute natural gas (SNG) production, technological and economical assessments were made, and tasks to discharge for the development were discussed. In this fiscal year, the results of surveys conducted in the past five-year period were compiled, and studies were made to prepare for a smooth transition to the element research stage. Findings obtained are described below. SNG producing technologies need to be developed, with the demand for SNG increasing sharply, to further stabilize the base for SNG supply; coal which is abundantly available should be used as the material for SNG; and coal hydrogasification, among various methods for producing SNG from coal, is the most suitable in view of efficiency and cost performance. It was also found after a prolonged study for the improvement of efficiency and cost performance that probabilities were high that the yield of BTX (benzene, toluene, xylene) would increase and cost performance would improve. Besides, a basic plan and an element technology research plan were prepared for the development of the ARCH (advanced rapid coal hydrogasification) process. (NEDO)

Development of hot water utilizing power plants in fiscal 1999. Development of technology to collect geothermal resources in great depths/Development of technology to excavate geothermal resources in great depths (Designing whole development); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu (zentai kaihatsu sekkei)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Technological development has been made on excavation of geothermal wells, which are dense, hard, and high in temperature and pressure, in developing geothermal resources in great depths. This paper summarizes the achievements in fiscal 1999. This fiscal year has performed the excavation test using an actual well to verify the reliability in practical use of the developed heat-resistant and durable bit. The test was executed by using a bit with a diameter of 8-1/2 inches in a ground bet having a maximum temperature of 300 degrees C in the Yamakawa geothermal field. As a result, good site evaluation was obtained that the wear and tear after lift-up showed no problems, and sufficient performance was verified in the drilling rate and durability. In addition, the low specific gravity cement for high temperature use that has been newly developed was given a cement mixing test to identify its workability at site and hardening properties, at a test well with a temperature of about 40 degrees C in the Okiri geothermal field. The actual well test was performed in a large-scale lost water occurred in a return well during an excavation by Nittestu-Kagoshima Geothermal Company. Effects were recognized in measures to prevent water loss. (NEDO)

FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on technology development of utilization of biological resources such as bioconsortia (development of analytical techniques of bioconsortia); 1997 nendo sangyo gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Bioconsortia are microbial composites composing of more than two kinds of microorganisms with special functions. To utilize their advanced functions, some techniques have been developed for analyzing their functions and interactions, and for identification, separation and incubation of the constituent microbial groups. In FY 1997, an investigation was made on technology trends, domestic researchers, and research topics related to bioconsortia. To manage and promote the progress of research at the National Institute of Bioscience and Human-Technology where the centralized management of this project is conducted, meetings are held once a month to examine the progress at the institute, in which reports are made and discussions are held on how each research item is progressing. In addition, meetings of the committee to promote research are held every other month to consider and examine measures required for promoting the research. Re-entrustment of research has been made on two subjects, i.e., `Studies on biological significance of symbiotic microorganisms` by Prof. Ishikawa of the University of Tokyo, and `Study on the relationship between the biosynthesis of useful terpenic materials of plant origin and the differentiation of plant tissues, and their effective production by plant cell cultures` by Prof. Inoue of Gifu Pharmaceutical University. 27 refs., 13 figs., 1 tab.

FY 1999 Advanced research and development project under New Sunshine Project. Study on supercritical solvolysis reaction; 1999 nendo chorinkai ryutai riyo gijutsu sendo kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for the chemical processes which utilize supercritical fluids, in order to establish the basic technologies for the environment-friendly chemical processes. For the solvolysis, the conditions under which plastics are hydrolyzed in supercritical water are investigated, and the basic data are obtained for the optimum conditions under which thermoplastic resins are hydrolyzed. The mechanisms involved in hydrolysis of polymers in supercritical water are elucidated to some extent. The environment-friendly process for synthesizing polycarbonate in supercritical carbon dioxide gas is investigated, and the continuous flow sheets are established for securing almost 100% conversion in the presence of an inexpensive catalyst. For the oxidation, the tests are conducted to burn low-grade coal in supercritical water, and the conditions under which it is burnt without releasing acid and toxic gases are found. For the hydrogenation, heavy fuel oil is treated in supercritical water to produce the lighter products. The conditions under which light oils and gases are produced are clarified, and the basic data are obtained for producing light gases from the resultant coke as the by-product. (NEDO)

Report on evaluation of research and development of resources recycling/reutilization systems. Phase 2; Shigen saisei riyo gijutsu system no kenkyu kaihatsu (dainiki) ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-08-01

Described herein are the final evaluation results obtained by the 7-year R and D project, beginning in the FY 1976, established by the national project system for developing the techniques for treating urban solid wastes. This project has developed a semi-wet type selective crushing/sorting unit for sorting the wastes, and established the elementary techniques for recycling the wastes into various products, e.g., compost, pulp, combustible gases, aggregates, methane gas, or fuel oil. Two types of total treating systems, in which these elementary techniques are integrated, have been developed; one is to recover materials and the other energy. They can comprehensively, efficiently treat the wastes, adapting themselves to various situations. Pyrolysis which discharges reduced quantities of flue gases is adopted. Waste water is treated, mainly by biological treatment which is supported by the conventional methods, e.g., coagulation and adsorption. The cost estimation results indicate that the total system developed by this project can compare favorably with the conventional incineration system under general conditions, at a capacity of 300 t/d or more, when taking into consideration the secondary effects brought by the recycling/reutilization. This system is commercially feasible, when it meets with local characteristics, e.g., garbage collecting systems, market values of recycled resources, treatment/disposal conditions, and natural and social environments. This project has sufficiently achieved the original objectives. (NEDO)

Some future projects in space activities. Centering around utilization of moon and satellite; Uchu kaihatsu no mirai koso ni tsuite. Tsuki/wakusei no riyo wo chushin ni

Energy Technology Data Exchange (ETDEWEB)

Saito, T [Obayashi Corp., Osaka (Japan); Kobayashi, H [Taisei Corp., Tokyo (Japan); Takagi, K [Shimizu Corp., Tokyo (Japan)

1994-09-05

Imagining a space in the middle of the 21st century, a space station installed with the artificial gravity generation facility is constructed, and a space factory utilizing a gravity free environment is also constructed. The construction materials for the space structures of this kind are prepared from the resources of the Luna. A solar power generation satellite being arranged with the solar cells manufactured from a silicon of the Luna is allocated on a geostationary orbit, and a power generated is supplied to the earth by the microwave. In such a time, a regular liner to the Luna and a ferry boat to the Mars will have come to fly, and furthermore an oxygen used for the propellant to them as well will be supplied from the Luna. In order to realize such a conception, there are various problems to be overcome such as a transportation problem first of all, a long life problem in the Luna and Mars bases and so forth. Furthermore a consideration to the environmental conservation of the Luna and Mars is also required. The nature of the Luna without a crustal alteration, meteorological phenomena, and organisms has no force to restore an environmental destruction. As for a space development in the future, it is desired that it should not damage a nature of the space and should be a field to chase a possibility of the human beings for a long time. 30 refs., 14 figs., 1 tab.

Fiscal 1996 verification survey of geothermal exploration technology. Development of the fracture type reservoir exploration method (development of the elastic wave use exploration method); 1996 nendo chinetsu tansa gijutsu nado kensho chosa. Danretsugata choryuso tansaho kaihatsu (danseiha riyo tansaho kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of exploring accurately fracture groups greatly restricting the fluid flow of geothermal reservoirs, technical development was made for applying the elastic wave exploration technology such as the high precision reflection method, VSP, elastic wave tomography to the geothermal exploration. The Okiri area, Kagoshima prefecture was selected as a demonstrative field of a typical type where the steep and predominant fracture rules the geothermal reservoir, and experiments were conducted using the high precision reflection method and VSP. Fracture models were made, and the analysis results were studied by a survey using the array CSMT/MT method and by a comparison with existing data. Reformation of the underground receiving system used for VSP and elastic tomography is made for improvement of its viability, and was applied to the VSP experiment. The treatment/analysis system of the core analyzer was improved, and cores of the demonstrative field were analyzed/measured. Further, the exploration results, core analysis results and existing data were synthetically analyzed, and fracture models of the demonstrative field were constructed. Also, effectiveness and viability of the elastic wave use exploration method were studied. 90 refs., 418 figs., 24 tabs.

Research and development of utilization technology of solar thermal energy system for industrial and other use. International joint technology development for solar energy utilization systems; Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for international joint technology development for solar energy utilization systems. The joint study with an Indonesian research institute takes a model of lumber drying plant for the design and feasibility study. All the parts it needs are technically available in Indonesia, except carbon fiber sheets and electronic devices for controlling purposes. The drying cost is higher than that of a plant which procures charge-free wood fuel, but lower than that of a plant which procures fuel at 30$/t. A cacao drying plant model is also studied. The feasibility study shows that the initial investment for the blowing-up model is much higher by 60% to 100% than that for the conventional plant. Its fuel cost is lower by 11% than that of residual oil but 27% higher than that of wood. 4 figs.

Hydrogen utilization international clean energy system (WE-NET). Subtask 8. Development of hydrogen combustion turbines (development of combustion control technology); Suiso riyo kokusai clean energy system (WE-NET). Subtask 8. Suiso nensho turbine no kaihatsu nensho seigyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper described the fiscal 1996 developmental results of hydrogen burning turbine combustion technology in the hydrogen utilization international clean energy system (WE-NET) project. A test was conducted on an annular type combustor where oxygen is mixed with steam (inert gas) at burner and fired with hydrogen. Appropriate flame shape and cooling/dilution vapor distribution were attempted, and various data on combustion were measured for improvement. Mixture and flame holding were improved by developing a can type combustor (1) where oxygen is diluted with steam after firing oxygen and hydrogen around burner and by strengthening circulation in the combustor. Improvement such as appropriate steam distribution, etc. is needed. A can type combustor (2) was tested in which the premixed oxygen and hydrogen is supplied from scoop and fired with hydrogen. By supplying part of oxygen from the primary scoop, the residual hydrogen and oxygen concentration around the stoichiometric ratio can be reduced. Concentration of the residual oxygen can be measured by the absorption light method, but it is difficult to adopt the non-contact measuring method to hydrogen. An outlook for the gas temperature measuring method was obtained. 12 refs., 121 figs., 27 tabs.

Achievement report for fiscal 2000 on New Sunshine Project aiding program. Development of hot water utilizing power generation plant (Technological development of hot rock power generation system - development of elementary technologies); 2000 nendo nessui riyo hatsuden plant to kaihatsu seika hokokusho. Koon gantai hatsuden system no gijutsu kaihatsu (yoso gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to identify the possibility of a hot rock power generation system, technological R and D has been performed on structuring of a man-made hydrothermal system, fracture mapping, downhole measurement and a circulating extraction system. This paper summarizes the achievements in fiscal 2000. With regard to the long-term circulating extraction test, a circulating heat extraction and test device was installed at the hot rock experimental field in the Hijiori area in Yamagata Prefecture, where geochemical data collection and tests including analyses thereon have begun. In reservoir bed analysis, a well module was incorporated into a reservoir bed simulator to improve the module so that comparison with the data of actual production on the ground can be performed. For the fracture mapping, AE having been observed during the long-term circulation test was analyzed, whereas it was estimated that the seismic source would not move or expanded during this period. A PTS logging has been performed during the long-term circulation test to investigate characteristics of the flow-out zone of the injection well and the production zone of the production well. In making the fracture model, an initial model was fabricated to estimate heat extraction behavior in the long-term circulation test. (NEDO)

Report on New Sunshine Program-supported undertakings for fiscal 1995. Development of hot water power plant and deep-seated geothermal resources sampling/exploiting technologies; 1995 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen seisan gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Reported are the results of researches conducted in fiscal 1995. For the formulation of a general development design, data are collected about domestic high-temperature thermal wells through questionnaires and literature probing, and are scrutinized. As for the development of logging technology, a memory type PT (Pressure, Temperature) logger is experimentally constructed, and is found to properly operate in an environment of up to 350degC in a production well. An experimentally manufactured S-probe proves to be capable of heat insulation and sealing. In the field of PT monitoring, a high-temperature optical fiber is experimentally fabricated for study, capable of measuring temperatures up to 400degC. As for the development of high-temperature tracer monitoring technology, basic experiments are conducted about the thermal characteristics of aromatic acids, and preparatory experiments about gas phase tracers. In the study of scale monitoring technology, deep-seated fluids are collected and analyzed. In the field of production control, technical problems are discussed and information is gathered centering on methods for scale prevention and removal. 31 refs., 90 figs., 40 tabs.

Report on New Sunshine Program-supported undertakings for fiscal 1997. Development of hot water power plant and deep-seated geothermal resources sampling/exploiting technologies; 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu, shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Reported are the results of researches conducted in fiscal 1997. In the field of PTSD (Pressure, Temperature, Spinner flowmeter, fluid Density) well logging, the high-temperature performance of a memory type PT (Pressure, Temperature) well logger is confirmed in a demonstration test. As for the S-probe, modification is effected for the reduction of the outside diameter from 70mm to 56mm, and tests are conducted in real wells. As for the D-probe, a laboratory test is conducted and then the probe behaves as predicted. In the field of PCT (Pressure, Chemical, Temperature) monitoring, the sampler is subjected to an on-site test in Italy, when water is successfully sampled out of the well. In the field of scale monitoring technique, deep-seated fluid is collected and examined, and the scale deposition rate in the deep-seated fluid is determine. For the study of production control technology with respect to scale prevention and removal, an Mg-Si scale synthesis test is conducted in the temperature range of 100-300degC, and it is found that the solubility of scale decreases with a rise in temperature. 19 refs., 93 figs., 24 tabs.

Development of a material for preventing fluidization of asphalt laid on a road by using coal-ash. Sekitan hai riyo ni yoru asufaruto hoso ryudoka boshizai no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, T. (Tohoku Electric Power Co. Inc., Sendai (Japan). Electric Power Engineering Lab.); Yamada, Y. (Taiseirotec Corp., Tokyo (Japan)); Chiba, Y. (Ministry of Construction, Tokyo (Japan))

1993-05-30

Currently, although prevention of fluidization of asphalt using modified asphalt mixed with resin and rubber has been taken, application of such a fluidization prevention means is limited, due to the reasons of high cost and difficult quality control, particularly mainly to places in the vicinity of intersections where the traffic is heavy, on bridges and in tunnels where construction is difficult. In addition, although low penetration asphalt is used, in this case, there are problems of deterioration of wear resistance and of cracks caused by temperature stress at low temperatures. The writers have conducted a study of imparting asphalt a fluidization resistance by adsorbing light oil in asphalt on a coal-ash fluidization preventing agent (FB) mixed in advance in an asphalt mixture. This article reports a study about the influence of mixing ratio and grain size of coal-ash upon the anti-fluidization property and durability of asphalt when coal-ash discharged from coal thermal power plants is mixed into asphalt, and a confirmation of the effectiveness of the mixing of coal-ash by actual road tests. 6 refs., 22 figs., 11 tabs.

Research and development of system to utilize photovoltaic energy. Survey on the specific purpose modules; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyoto module ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on the specific purpose modules for photovoltaic power generation in fiscal 1994. (1) On the feasibility survey on new application fields, it was clarified that photovoltaic power generation is applicable to extensive areas such as farmland, road, railway and public facility as latent demand sites. (2) On the optimum modules for various specific purposes, the structure, production method, cost estimation and issues of various modules were studied for desert, wasteland, coast, ocean, river, embankment, railway, road, mobile facility and arcade. (3) On the survey on new materials and material development, various conventional materials and materials promising for required performance were surveyed for every application. (4) On the survey on technology trends, the survey members participated in the first international photovoltaic energy conversion conference and the photovoltaic power generation workshop, while the members held the 1st-5th specific purpose module subcommittees. 1 tab.

Achievement report for fiscal 1997 on the development of technologies for utilizing biological resources such as complex biosystems. Development of complex biosystem analyzing technology; 1997 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei kaiseki gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The aim is to utilize the sophisticated functions of complex biosystems. In the research and development of technologies for effectively utilizing unexploited resources and substances such as seeweeds and algae, seaweeds are added to seawater to turn into a microbial suspension after the passage of two weeks, the suspension is next scattered on a carageenan culture medium, and then carageenan decomposing microbes are obtained. In the research and development of technologies for utilizing microbe/fauna-flora complex systems, technologies for exploring and analyzing microbes are studied. For this purpose, 48 kinds of sponges and 300 kinds of bacteria symbiotic with the sponges are sampled in Malaysia. Out of them, 15 exhibit enzyme inhibition and Artemia salina lethality activities. In the development of technologies for analyzing the functions of microbes engaged in the production of useful resources and substances for animals and plants, 150 kinds of micro-algae are subjected to screening using protease and chitinase inhibiting activities as the indexes, and it is found that an extract of Isochrysis galbana displays an intense inhibitory activity. The alga is cultured in quantities, the active component is isolated from 20g of dried alga, and its constitution is determined. (NEDO)

Report on the research and development achievements in fiscal 1999 on the international research cooperation project for comprehensive development and utilization technologies for gas hydrate resources; 1999 nendo gas hydrate shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper reports the achievements in fiscal 1999 on development of gas hydrate resources. As a result of synthesizing gas hydrates in deposit systems, identifying stability zones in compositions, and studying thermal conductivity and dielectric constant of the deposits, the estimation accuracy has been enhanced steadily in estimating hydrate existing areas in actual frost areas. In the collecting technologies, a proposal was presented for a system by which carbon dioxide is introduced into ground beds at the same time as recovering gases, and gas hydrates are displaced with carbon dioxide hydrates. The displacement phenomenon was verified experimentally by controlling temperatures and pressures. Even below the freezing point, the production rate of the carbon dioxide hydrates is fast if it is above minus 4 degrees C. Salt diffusion behavior important in control of the production and decomposition, and action mechanisms of production and suppression agents were made clear microscopically. Experimental and theoretical discussions were given on dynamics of the production and decomposition. The cage occupation rate of methane hydrates was quantitatively measured successfully by using the Raman spectroscopy. Hydrates of gas mixture were utilized to have verified the possibility of separating the gas mixture constituents. (NEDO)

FY 1998 'The New Sunshine Project' leading R and D. Report on the results of the leading R and D of supercritical fluid utilization technology; 1998 nendo 'New Sunshine Keikaku' sendo kenkyu kaihatsu. Chorinkai ryutai riyo gijutsu sendo kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The paper reported the FY 1998 achievement of the supercritical fluid utilization leading R and D which started in FY 1997 on a 3-year plan. In the R and D, solvolysis reaction, oxidation reaction and hydrogenation reaction were taken up in the chemical process using supercritical fluid. In the study of solvolysis reaction, the basic data were obtained on decomposition conditions of thermoplastic and thermosetting plastics in supercritical water. Further, concerning the synthesis of environmental friendly type carbonate using CO2, a conversion rate of almost 100% was obtained. About the oxidation reaction, conditions were found out for burning low grade coal in supercritical water without emitting acid gas. This is considered to lead to a possibility of the supercritical water power generation. Relating to the hydrogenation reaction, a study was made on lightening technology of heavy distillate using supercritical water, and the conditions for effective emission of methane and hydrogen were found out. As to the base technology, a study was made of metal materials with high corrosion resistance against supercritical water. (NEDO)

Fiscal 1998 R and D report on femtosecond technology (power generation facility monitoring system using high- intensity X-ray pulse); 1998 nendo femuto byo technology no kenkyu kaihatsu (kokido X senb pulse riyo hatsuden shisetsu monitoring system no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report reports the fiscal 1998 R and D result of Femtosecond Technology Research Association (FESTA) supported by NEDO. For creation of industrial basic technologies supporting the advanced information society in the 21st century, ultra-high speed electronics technology including new functions beyond the speed limit of conventional electronics technologies is indispensable. From such viewpoint, this R and D aims at establishment of the basic technology controlling conditions of beams and electrons in a femtosecond (10{sup -15}-10{sup -12} seconds) region. In development of the titled system, this R and D aims at generation of high-intensity X-ray pulse by interaction between femtosecond light pulse and high-density electron beam pulse, and development of measurement technology (non- stop inspection) of high-speed moving objects using such X- ray pulse. In fiscal 1998, this project succeeded in time stabilization of laser oscillators at a 100fs level and generation of low-emittance electron beam pulse through development of ultra-short pulse synchronization, laser stabilization and electron beam pulse generation technologies. (NEDO)

Fiscal 1980 Sunshine Project research report. Development of hydrothermal power plant (Development of binary cycle power plant). Supplement. Research on plant technology; 1980 nendo nessui riyo hatsuden plant no kaihatsu seika hokokusho. Binary cycle hatsuden palnt no kaihatsu bessatsu (plant gijutsu kenkyu chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

Research was made on new geothermal power plant technologies such as downhole pump and dual boiler for development of the 10MW class binary cycle power plant using geothermal energy. In heat cycle calculation of dual boilers, the cycle performance of a subcritical multi-stage evaporation cycle with R-114 heat medium was obtained through cycle calculation, heat conduction calculation and profitability calculation. The calculation result suggested possible considerable reduction of heat loss due to heat exchange at a preheater and evaporator, and considerable reduction of discharge loss of hot water by such multi-stage evaporation cycle. In American, every geothermal binary cycle power plant adopts pressurized heat exchange between hot water and heat medium by using downhole pumps, and pressurized reinjection of hot water into the ground. Since downhole pump itself not yet satisfies its requirements enough, it is said that Department of Energy is now under consideration on the future R and D. (NEDO)

Fiscal 1993 achievement report. International Clean Energy Network Using Hydrogen Conversion (WE-NET) technology (Subtask 8 - Research and development of hydrogen combustion turbine - Development of ultrahigh-temperature materials); 1993 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET). (Subtask 8. Suiso nensho tabin no kaihatsu - Cho koon zairyo no kaihatsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Current technologies are surveyed and tasks to discharge are extracted relating to heat resistant alloys, intermetallic compounds, ceramic based composite materials, and carbon based composite materials, which are expected to be used for hydrogen combustion turbines. Concerning oxide dispersion strengthened alloys for cooled vanes, tasks to discharge are extracted, which relate to the designing, development, and selection of vane materials, bonding layer materials, and coating materials, and to thermal barrier coating techniques and machining techniques. Concerning porous fiber reinforced ceramic materials for ceramic shells, tasks involve the elucidation of corrosion behavior and manufacturing techniques. MoSi{sub 2}, which is a promising high-melting intermetallic compound, also presents some tasks to discharge for an increase in its high strength and high ductility in an ultrahigh-temperature steam/reducing atmosphere, and for improvement in manufacturing techniques. For the carbon/carbon composite material which is the sole material usable in the ultrahigh-temperature domain of 2,000 degrees C, an analysis and evaluation method taking its anisotropy into consideration needs to be developed, and an oxidation resistant coating has to be also developed. In addition to the designing and development of these materials, development is necessary of materials testing and evaluating techniques. (NEDO)

Development of hot water utilizing power plants in fiscal 1999. Development of binary cycle power plant (Development of system to detect well bottom information when geothermal hot water is excavated); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu (chinetsusei kussakuji kotei joho kenchi system no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Developmental research has been performed on the MWD system to identify on the real time basis the information about well bottom when geothermal hot water is excavated (azimuth, inclination, pressure and temperature). This paper summarizes the achievements in fiscal 1999. In the developmental research on the detection device, attempts were made in improving the zonde, and enhancing its heat resisting performance. In addition, data were acquired on electronics parts as a result of the heat resistance identifying test. For the on-the-ground devices, improvement was made to add the experiment analyzing program with a program to remove the downhole motor pressure noise. The pressure noise during excavation in the actual wells was collected. In the analyzing system, use of PC, improvement, and operation check were performed on the well trace projecting and indicating system. Operation of the well trace estimating system was checked by using the actual data in order to prepare the operation manual. With regard to the well evaluation supporting system, improvement, operation check and that by using the actual data were executed on the PC version temperature analyzing system. Performance of the zonde was verified by the actual geothermal well test. (NEDO)

Development of hot water utilizing power plants in fiscal 1999. Development of technology to collect geothermal resources in great depths (Development of technology to produce geothermal resources in great depths); 1999 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to develop geothermal resources, research and development has been performed on the production technologies for the deep-seated geothermal resources, such as pressure, temperature, flow speed and density (PTSD) logging technologies. This paper summarizes the achievements in fiscal 1999. In the actual well test on the developed D-probe, it was verified that the probe operates normally under high temperature environment (342 degrees C) which exceeds the measurement limit of conductive cables (315 degrees C). In developing the PTC monitoring technology, the downhole sampler was improved, and a test was performed in the actual hole in the Hijiori area in Yamagata Prefecture. As a result, collection of hot water of about 900 mL has become possible. In developing the high-temperature tracer monitoring technology, simulation was performed keeping in mind charging the tracer into the Hijiori geothermal area, whereas specifications for charging and collecting the tracer were determined. In developing the scale monitoring technology, experiments were carried out on the fluid systems under deep geothermal conditions by using scale forming devices, by which it was indicated that silica is the important scale constituent. (NEDO)

Fiscal 2000 survey report. Survey report on development and utilization of alternative energies for oil in Pacific region; 2000 nendo Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A survey was conducted, with environmental matters taken into consideration, for building an information gathering infrastructure for the countries in the Pacific region, capable of promptly and accurately collecting and offering energy related information. Conducted in this fiscal year were regular data gathering, review of oil supply and demand and alternative energy supply and demand in the Pacific region, on-site survey of alternative energy development and utilization in Vietnam, quarterly analyses of trend of energy demand, and the like. The supply of primary energy in the Pacific region increased by 2.3% per year in the period 1980 through 1998. The rate of increase was the lowest with oil, and the highest with hydroelectricity, atomic power, and recoverable energies such as geothermal energy. The Vietnamese Government is promoting its efforts to develop power sources by use of recoverable energies for farm village electrification. Efforts are being earnestly exerted to develop its rich natural gas resources and it is expected that there will be a remarkable achievement in the use of alternative energies due to an increase in natural gas consumption. In the field of data collection, various data were registered with the database. (NEDO)

Improvement of effective utilization technology of wood-based resources and development of their new application fields. Mokushitsukei shigen no yuko riyo gijutsu no kojo to shin prime yoto kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kamiya, F.; Haishi, T.; Sueyoshi, S.; Sotozaki, M.; Kato, A.; Hayashi, Y.; Ito, Y.; Hirabayashi, Y.; Togawa, E.; Obino, T. (Forestry and Forest Products Research Institute, Ibaraki (Japan))

1991-09-01

On advanced work and use techniques for wood, the aseismic property of plywood-nailed bearing walls was analyzed by seismic response experiments on an excitor resulting in the sufficient aseismic property beyond usual design specification, and the load deformation model was proposed based on experimental results. The evaluation method of heat insulation for wood houses was also developed, and the simple estimation method of room temperature change and the index for evaluating heat insulation for every structure were proposed. On advanced modification and use techniques for constituents of wooden resources, the chemical structure of saponin in woods was studied together with the relation between the chemical structure and biological activity of unknown saponins synthesized from triterpene. The pervaporation property of organic composite films composed of chitinous substances and cellulose derivatives from natural polymers was also studied to develop pervaporation films effective in separating water from ethyl alcohol. 11 figs., 3 tabs.

Fiscal 1999 survey report. Survey of development and utilization of energy substitutes for oil in the Pacific region; 1999 nendo Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The Pacific region is a densely populated region where economy is developing at a high pace with China and other newly industrialized economies at the core. When energy balance in the region is studied, it is found that China and some others have already turned pure importers of energy and that probabilities are high that, along with development of economy and improvement on living standards, all the nations in the region will become pure importers. Accordingly, in the presence of urgent problems of global pollution and oil resources depletion, it is important to make sure that data particularly about the development of substitute energies for oil in this region be collected and duly dealt with for accurately predicting future developments. In this survey, a database is to be built to grasp the trends of energy supply and demand with attention focused on substitutes for oil which are available at hand. In this fiscal year, data for 1997 were added to the database for analysis into demand and supply of substitutes for oil in the Pacific region, and energy data were gathered for this purpose. Detailed tables of balance were compiled, broken down by energy source. Other detailed tables of balance were also prepared, these broken down by ultimate consumption department. (NEDO)

FY 1999 report on the results of the R and D of the global environmental industry technology. R and D of the CO2 fixation/effective use technology using bacteria/algae; 1999 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of developing the technology to fix CO2 and recycle it as resource in higher efficiency than that in photosynthesis in the nature world, study of bacteria, etc. was made in terms of the search, breeding, and artificial realization of the growth environment, etc. The FY 1999 results were summed up. As to high efficiency photosynthetic bacteria/microalgae, conditions for sampling/breeding/optimum culture of bacteria were established and made database. From conditions for the optimum CO2 fixation by photosynthetic bacteria, oxygen injury prevention culture method, continuous culture experiment, etc., it was found out that the carbyne cycle was a main route of the carbon fixation also in photosynthetic bacteria. As to the cell fusion, established were the technology of electric fusion of interspecific fusion strains and the technology of evaluation of growth characteristics. Also studied was a method to transfect genes into Chlorella sp. which fixes CO2. Concerning the light collecting reactor of 200L scale, a high concentration culture experiment was carried out using Chlorella sp. UK001 as the strain tested, and the engineering data on the behavior in culture tank, multiplication speed, etc. were collected. (NEDO)

Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. International joint technology development for solar energy utilization systems; 1998 nendo sangyoyo nado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The solar energy utilizing technologies having been developed under the Sunshine Project were used to have executed the international joint technology development on the 'solar heat utilizing drying system' in the Republic of Indonesia. This paper summarizes the achievements in fiscal 1998. In operating the pilot plant, three operational experiments out of seven experiments were carried out only by Indonesian engineers. As a result of the drying experiments, the heat collecting characteristics of the collector were as about half at 19 to 30% as the efficiency assumed in the design of 50%. The reason for this can be attributed to the fact that the cover glass used in the demonstration test in Japan had light permeability of about 87%, but the cover glass used in the test plant was made of frosted glass whose light permeability was about 37%. This glass is the only glass available for a heat collector in the solar heat hot water device in Indonesia, but is unsuitable for the heat collector. Another cause was that the insolation at the site was lower by about 30% than the one used at the design stage. (NEDO)

Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. International joint technology development for solar energy utilization systems; 1998 nendo sangyoyo nado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The solar energy utilizing technologies having been developed under the Sunshine Project were used to have executed the international joint technology development on the 'solar heat utilizing drying system' in the Republic of Indonesia. This paper summarizes the achievements in fiscal 1998. In operating the pilot plant, three operational experiments out of seven experiments were carried out only by Indonesian engineers. As a result of the drying experiments, the heat collecting characteristics of the collector were as about half at 19 to 30% as the efficiency assumed in the design of 50%. The reason for this can be attributed to the fact that the cover glass used in the demonstration test in Japan had light permeability of about 87%, but the cover glass used in the test plant was made of frosted glass whose light permeability was about 37%. This glass is the only glass available for a heat collector in the solar heat hot water device in Indonesia, but is unsuitable for the heat collector. Another cause was that the insolation at the site was lower by about 30% than the one used at the design stage. (NEDO)

Achievement report on research and development of basic technologies for the next generation industries in fiscal 1981. Research and development of a recombinant DNA utilizing technology; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Achievements were compiled on the research in fiscal 1981 on the 'research and development of a recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. For the method to create energy saving type bacteria stocks for processes centering around the escherichia coli, refinement was carried out on cytochrome P-450 and NADPH-cytochrome P-450 reduction enzyme respectively from hepatic microsome of rats administered with induction agents. Attempts were made to prepare antibodies working on them. For the method to create high-efficiency secreting bacteria stocks centering around bacillus subtilis, activity measurement and quantification were performed on enzymes external to the bacillus sutilis, and research was executed on introduction of neutral protease gene sensitive to bacillus subtilis temperatures into the NA20-S17 stock. For the method to create bacteria stocks to substitute raw materials used in the chemical industry, studies were performed on separation of enzymes and corresponding genes, and incorporation of the genes into the escherichia coli. In the comprehensive investigation and research on the recombinant DNA utilizing technology, information exchange and discussions meetings were held, and investigations were made on literatures and patents. (NEDO)

Hydrogen utilization international clean energy system technology (WE-NET). Subtask 8. Research and development of hydrogen combustion turbines (development of ultra-high temperature materials); Suiso riyo kokusai clean energy system (WE-NET). Subtask 8. Suiso nensho turbine no kenkyu kaihatsu chokoon zairyo no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper described the result of the fiscal 1996 development of ultra-high temperature materials for parts of hydrogen combustion turbines, as part of the hydrogen utilization technology, which have excellent environmental protectivity and remarkably high efficiency. By the optimized solution heat treatment of monocrystal alloy developed in the previous fiscal year, obtained was strength property the same as the existing super alloys. As to FRC, pore size and strength property of SiC organic hybrid were made clear. ODS alloy cooling blades and heat insulation coating were studied, and YSZ was found to be most excellent as coating material. Concerning intermetallic compounds, the applicability to ultra-high temperatures up to 1700degC was not obtained. For improvement of heat resistance and environment resistance, adopted were highly compacting SiC matrix and BN coatings. Al2O3 was excellent in long-time stability. In the 1600degC steam corrosion test on multiplex structural materials with Al2O3 as surface material, chemical stability was confirmed. Three-dimensional woven fiber reinforced composite materials of C/C{center_dot}CMC were trially produced by changing the fiber orientation, and improvement in ultra-high temperature thermal shock resistance was confirmed. A study was made of spot observation of the specimen surface by laser microscope, and development was conducted of a temperature measuring method with no influence of radiant heat. 44 refs., 250 figs., 40 tabs.

Commissioned operation report for fiscal 1991 on commissioning of surveying high-level development and effective utilization of natural gas, and development of coal hydrogasification technology; 1991 nendo tennen gas kodo kaihatsu yuko riyo chosa tou itaku gyomu hokokusho. Sekitan suiten gaska gijutsu kaihatsu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

With an objective of establishing a practically usable process to manufacture substitution natural gas, discussions have been given on the technical, economical, and developmental problems therein. This paper summarizes the achievements in fiscal 1991. The summary of surveys in the current fiscal year is as follows: the coal hydrogasification process is positioned as having high necessity in the gas industry because of its high thermal efficiency and low gas cost; in order to evaluate the reaction heat in the hydrogasification reaction, a mathematical model having flexibility was structured, whereas a large number of findings has been derived, including performance of the reactor and the optimum operating conditions; in addition to having made clear the conditions for an entrained bed hydrogasification reactor, comparisons and discussions were given on the internally circulating reactor and one-through reactor; studies were performed on thermal efficiency and gas cost in the optimized process configuration o the ARCH-1 process base; and a proposal was made on the test for a new reactor having the two-step reaction zone that could be expected of increased yield in aqueous solution, and could contribute to reducing the gas cost. (NEDO)

Achievement report on research and development of basic technologies for the next generation industries in fiscal 1981. Research and development of a recombinant DNA utilizing technology; 1981 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Achievements were compiled on the research in fiscal 1981 on the 'research and development of a recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. For the method to create energy saving type bacteria stocks for processes centering around the escherichia coli, refinement was carried out on cytochrome P-450 and NADPH-cytochrome P-450 reduction enzyme respectively from hepatic microsome of rats administered with induction agents. Attempts were made to prepare antibodies working on them. For the method to create high-efficiency secreting bacteria stocks centering around bacillus subtilis, activity measurement and quantification were performed on enzymes external to the bacillus sutilis, and research was executed on introduction of neutral protease gene sensitive to bacillus subtilis temperatures into the NA20-S17 stock. For the method to create bacteria stocks to substitute raw materials used in the chemical industry, studies were performed on separation of enzymes and corresponding genes, and incorporation of the genes into the escherichia coli. In the comprehensive investigation and research on the recombinant DNA utilizing technology, information exchange and discussions meetings were held, and investigations were made on literatures and patents. (NEDO)

Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 10. Development of low-temperature materials; 1999 nendo suiso riyo kokusai clean energy gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 10. Teion zairyo no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research result on material property test under liquid hydrogen environment, and development of optimum welding material and welding technique for the WE-NET plan. In the study on material properties in a liquid hydrogen temperature range, fatigue strength tests of base metals and weld metals were conducted under liquid hydrogen environment continuously, and further fatigue data were collected. As a result, it was clarified that both SUS304L and SUS316L have extremely high fatigue strength. To improve the tenacity of candidate weld metals under liquid hydrogen environment, material tests of welds were conducted on the laser-welded stainless steel joint and friction stir- welded Al alloy joint prepared by TWI (The Welding Institute) in the U.K. The laser-welded stainless steel joint showed higher low-temperature tenacity and lower ductility than TIG- welded joints. The friction stir-welded Al alloy joint showed extremely improved tensile strength and tenacity in a liquid hydrogen temperature range. For the low-temperature material database, both addition of new data and improvement of software were promoted. (NEDO)

Commissioned operation report for fiscal 1992 on commissioning of surveying high-level development and effective utilization of natural gas, and development of coal hydrogasification technology; 1992 nendo tennen gas kodo kaihatsu yuko riyo chosa tou itaku gyomu hokokusho. Sekitan suiten gaska gijutsu kaihatsu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

With an objective of establishing a practically usable process to manufacture substitution natural gas, discussions have been given on the technical, economical, and developmental problems therein. This paper summarizes the achievements in fiscal 1992. With respect to the possibility of applying the coal SNG to power generation fuel, a power generation system composed of coal SNG, pipeline transportation and natural gas was recognized of having the significance of technological development because of its capability of raising the power plant utilization rate and possibility of being superior in the economic aspect. In the study on enhancement of aqueous solution yield, performance of the ARCH-2 reactor was discussed by the simulation forecast using a mathematical model, whereas the benzene yield was found possible to be raised up to 15% in the carbon conversion rate. As the target of the hydrogasification process to be developed by Japan, based on the study results of the current fiscal year, three points consisted of SNG yield maximization, cooling gas efficiency maximization, and BTV yield maximization were indicated, and it was proposed that a process having flexibility in the product yield should be developed. (NEDO)

FY 1998 report on the results of the development of the utilization technology of biological resources such as bioconsortia. Development of the consortium based analysis technology; 1998 nendo fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu seika hokokusho. Fukugo seibutsukei kaiseki gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the purpose of establishing the analysis technology and industrial utilization technology required for the establishment of the utilization technology of consortia's high functions which are already used in the fermentation technology field over the limit of the conventional bio-technology using functions of single biological species, study was made to look for the consortium based analysis technology by which the consortium base can be analyzed as it is using the molecular biological method. Studies were made in the following four fields: 1) new identification technology of eucaryote using II DNA topoisomerase genes (PCR amplification method of II DNA topoisomerase genes); 2) method to detect new recognition peptide activated microorganism (adjustment of cortical antigen); 3) technology to elucidate detection/response mechanism of the specific environment and adaptation/resistance mechanism of the specific environment; 4) incubation method inside 3D matrices. In 3), studies were made of the analysis of inhibition mechanism of korormicin and separation of solvent-resistant oil degradable bacteria. In 4), for the settlement and dynamic analysis of microorganism consortium by studying incubation conditions, conducted was the molecular system analysis of bacteria and eumycetes inhabiting in sponge. (NEDO)

Fiscal 2000 achievement report on project for research and development of intelligent infrastructure creation and utilization technologies. Research and development of reference materials for polymers; 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu jigyo seika hokokusho. Kobunshi ni kansuru hyojun busshitsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

As one of the efforts to establish national reference materials at an accelerated pace in a concentrated manner, a comprehensive survey was conducted on reference materials for polymers, and research and research was conducted for the development of such. In the comprehensive survey, investigations were made into the actual use of reference materials for polymers and their management at private-sector enterprises and public research institutes in Japan and at research bodies in the U.S. and Canada. In the development of reference materials for polymers, a procedure was contrived for synthesizing monodisperse oligostyrene specimens, polymerization was carried out using an improved synthetic method, and molecular weight distribution was analyzed. Using a homogeneous oligostyrene reference material for calibration, the mean molecular weight of an oligostyrene reference material was accurately evaluated by size-excluded chromatography. In the case of a specimen with its mean molecular weight not more than 1,000, the result exhibited excellent agreement with what supercritical fluid chromatography indicated. In the development of reference materials for characteristics evaluation, this in relation to methods for evaluating thermomechanical characteristics of plastics, efforts were made to develop reference materials for evaluating dynamic viscosity/elasticity of solid plastics. (NEDO)

Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 8) - development of hydrogen production technology; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 8. Suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

R and D was conducted with the view of establishing hydrogen production technology based on the solid high polymer electrolyte water electrolysis method, which presumably offers higher efficiency and lower cost than conventional methods. This year, as well as implementing development of large-scale cell lamination (electrode area 2,500 cm{sup 2}, 10 cells) by using two hydrogen production methods (electroless plating method and hot press method), work was started for developing cells (electrode area 1,000 cm{sup 2}) for hydrogen stations. In the research on longterm durability improvement, with a 50 cm{sup 2} membrane electrolyte or cell, the evaluation test results were obtained of stable electrolytic performance showing more than 93% energy efficiency after 400 hour operation, under the conditions with electrolysis pressure 0.4MPa and electrolysis temperature 120 degree C. In a test of 1,000 cm{sup 2} prototype cell for hydrogen stations, the evaluation result was obtained for energy efficiency of 92% under the conditions with electrolysis pressure 0.5MPa and electrolysis temperature 120 degree C; thus, this year's target efficiency of over 90% was achieved. Further, enhancement of the quality was contrived for example by improving the electroless plating method and remodeling a roll press machine. (NEDO)

Achievement report on commissioned research and development of basic technologies for the next generation industries in fiscal 1982. Research and development of a recombinant DNA utilizing technology; 1982 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

Achievements were compiled on the research and development in fiscal 1982 on the 'recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. With regard to refined cytochrome P-450 molecular species, a material was obtained that has further higher specific content than those having been discovered in fiscal 1981. Refinement was carried out on antibodies against P-450 and NADPH-cytochrome P-450 reduction enzyme to raise the antibody values. Identification was made on the refined cytochrome P-450 molecular species. The P-450 in the mRNA products prepared in fiscal 1981 was quantified successfully by means of the immuno sedimentation process using protein A-sepharose. In fabrication of cytochrome P-450cDNA, detailed discussions were given on the cDNA fabrication and reaction conditions, where double-chain cDNA was obtained. In refining the enzymatic cytochrome P-450, discussions on culture conditions of the enzyme discovered a condition in which the P-450 content increases. (NEDO)

Achievement report for fiscal 1998 on World Energy Network (WE-NET). Subtask 8. Development of hydrogen combustion turbine (Development of main accessories); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) seika hokokusho. 8. Suiso nensho turbine no kaihatsu (shuyo hokirui no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report covers the effort to develop hydrogen-fueled turbines under the international clean energy project. In the development of technologies for the use of liquid hydrogen cold heat, studies are conducted about the emergency stop of an air separating device for a 1,000MW power plant and about a backup system, various details and specifications are defined, and a tentative design is prepared for the whole system. Studies are made about economic efficiency, which lands on a oxygen production cost of 10.92 yen/Nm{sup 3}. In the development of high-temperature heat exchangers, the results are evaluated of the competition which has been under way since 1997 between two entrusted corporations over the topping regeneration cycle technology. In this fiscal year, the evaluation is accomplished by the main accessories development subcommittee, and the Toshiba Corporation wins first place, and the Mitsubishi Heavy Industries, Ltd., second place. It is found, however, that the conceptual designs are both feasible from the technological point of view. In addition, tasks to study for the next project are put together. (NEDO)

Achievement report on commissioned research and development of basic technologies for the next generation industries in fiscal 1982. Research and development of a recombinant DNA utilizing technology; 1982 nendo jisedai sangyo kiban gijutsu itaku kenkyu kaihatsu seika hokokusho. Kumikae DNA riyo gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

Achievements were compiled on the research and development in fiscal 1982 on the 'recombinant DNA utilizing technology', which has been performed according to the 'institution for research and development of basic technologies for the next generation industries'. With regard to refined cytochrome P-450 molecular species, a material was obtained that has further higher specific content than those having been discovered in fiscal 1981. Refinement was carried out on antibodies against P-450 and NADPH-cytochrome P-450 reduction enzyme to raise the antibody values. Identification was made on the refined cytochrome P-450 molecular species. The P-450 in the mRNA products prepared in fiscal 1981 was quantified successfully by means of the immuno sedimentation process using protein A-sepharose. In fabrication of cytochrome P-450cDNA, detailed discussions were given on the cDNA fabrication and reaction conditions, where double-chain cDNA was obtained. In refining the enzymatic cytochrome P-450, discussions on culture conditions of the enzyme discovered a condition in which the P-450 content increases. (NEDO)

Report on a survey in fiscal 1998 for petroleum substituting energy development and utilization in the Pacific Ocean region; 1998 nendo Taiheiyo chiiki sekiyu daitai energy kaihatsu riyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A survey was carried out to make available the information base that can collect, put into order and provide quickly and accurately the energy related information based on global environment problems in the Pacific Ocean region. Fiscal 1998 has performed a substituting energy demand and supply analysis in the Pacific Ocean region by adding the 1996 data, in addition to collection of the normal energy data. For the purpose of analyzing the petroleum substituting energy demand and supply in the Pacific Ocean region, data were collected from 17 countries for fiscal 1997 and the quarterly data for 1998. Retroactive data collection was also continued. The growth rate of primary energy supply in the Pacific Ocean region is 1.8% in average in the 1980's, and 3.8% in the 1990's. In contrast, the growth rate of petroleum substituting energies is 6.4% in the 80's and 6.2% in the former half of the 90's, being far higher than the growth rate of the primary energy supply. The share of the petroleum substituting energies accounting for in the primary energy supply has increased from 6.7% in 1980 to 12.1% in 1996. As the breakdown, nuclear power accounts for overwhelmingly large, followed by geothermal energy and new energies. (NEDO)

Survey on utilization of database for research and development of global environmental industry technology; Chikyu kankyo sangyo gijutsu kenkyu kaihatsu no tame no database nado no riyo ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

1993-03-01

To optimize networks and database systems for promotion of the industry technology development contributing to the solution of the global environmental problem, studies are made on reusable information resource and its utilization methods. As reusable information resource, there are external database and network system for researchers` information exchange and for computer use. The external database includes commercial database and academic database. As commercial database, 6 agents and 13 service systems are selected. As academic database, there are NACSIS-IR and the database which is connected with INTERNET in the U.S. These are used in connection with the UNIX academic research network called INTERNET. For connection with INTERNET, a commercial UNIX network service called IIJ which starts service in April 1993 can be used. However, personal computer communication network is used for the time being. 6 figs., 4 tabs.

Research and development of system to utilize photovoltaic energy. Survey on the evaluation of photovoltaic power generation; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyoko hatsuden hyoka no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the survey results on evaluation of PV power generation in fiscal 1994. (1) On the evaluation technique of energy pay-back time, foreign trial calculation examples by integration method were surveyed. However, there were not many study examples, and the calculation basis of input energy was also ambiguous. The calculation result by input-output analysis in Japan gave the value more than that by integration method, pointing out that indirect input energy is essential. (2) On the evaluation technique of the degree of environmental contribution, CO2 emission of the PV generation system installed on ordinary housing roofs was calculated to estimate reduction of CO2 emission and cost. As a result, PV power generation as reduction measures against CO2 brought a little cost increase. (3) On the latent scale of PV power generation, it was estimated to be nearly 191GW although under no restriction. It was a considerably large value as compared with the current power generation capacity in Japan. 4 tabs.

Next-generation coal utilization technology development study. Environmentally-friendly coal combustion technology; topping cycles; Sekitan riyo jisedai gijutsu kaihatsu chosa. Kankyo chowagata sekitan nensho gijutsu bun`ya (topping nensho gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

As a realistic measure to reduce environmental pollutants emitted from coal-fueled boilers, a developmental study was conducted of high-efficient combustion systems. In fiscal 1994, four types of topping cycles which are different in system structure and gasifier type were selected, and topping cycles assuming a 300MW-class power plant were trially designed. Further, an evaluation of adaptability of these systems was made, and an selection of the optimum system for the early development was made among the systems. As a result, the evaluation was obtained that `a system using air blown gasifier` is most suitable for conducting the next-stage research. In the element test on the topping combustion technology, collection was made of data of desulfurization activity, desulfurization oxidation mechanism and alkali metal behavior at the laboratory level, data of temperatures and gas concentration distribution in coal gasification, data of simulation of the gasifier reaction, and the other data. 262 figs., 66 tabs.

Results of the supplementary work to the fiscal 1994 New Sunshine Project. Development of geothermal power plants, etc. (development of production, technology for deep-seated geothermal resources); 1994 nendo new sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant to kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu shinbu chinetsu shigen seisan gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The paper reports on the fiscal 1994 results of the study of the development of a technology for collecting deep-seated geothermal resources, which has been made for increasing the capacity of the geothermal power generation as a part of the New Sunshine Project. As a plan for the development, a development is made of logging equipment and its auxiliary system and then characteristics of the deep-seated geothermal well are clarified. The logging equipment is a PTSD (pressure/temperature/spinner flow-meter/fluid density) logger which stands the use at deep-seated geothermal wells of 400{degree}C and 490 kgf/cm{sup 2} and measures pressure, temperature, flow rate and fluid density under static and dynamic conditions. In this fiscal year, metal seals were developed for preventing geothermal fluids from penetrating into the PT probe. Qualities and inner/outer diameters of various kinds of structural materials used in the S probe were determined, and output necessary enough to detect the rotation number is obtained. Measuring precision of D logging by {gamma} rays was evaluated. The study was made of the monitoring technology including the borehole and ground measuring system, the borehole fluid sampling and the scale formation. Relating to the tracer widely used in monitoring of hydrothermal reservoirs, investigated was the trend of the technology from abroad. 8 refs., 60 figs., 26 tabs.

Achievement report for fiscal 2000 on New Sunshine Project aiding program. Development of hot water utilizing power generation plant (Development of deep seated geothermal resource collection technologies - development of deep seated geothermal resource production technologies); 2000 nendo nessui riyo hatsuden plant to kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu (Shinbu chinetsu shigen seisan gijutu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Items of information about deep seated geothermal resource production technologies were collected, and tests and studies were performed using actual wells. This paper summarizes the achievements in fiscal 2000. In developing the PTDS logging technology, it was verified in the actual well tests that the measured density of a D probe is consistent with the theoretical density, and the accuracy is satisfactory. The extended time measurement at fixed points on temperatures of fluids in the wells, pressures, flow rates, and fluid densities has identified chronological change of the characteristics of the fluids in the wells, including the enthalpy, proving them to be effective in well control. In developing the PTC monitoring technology, a fluid extracting machine for the downhole fluid sampler was fabricated, which has collected hot water successfully in the actual well twice out of seven attempts. In developing the high temperature tracer monitoring technology, experiments were performed using vapor phase and liquid phase tracers, whereas re-discharge of all the tracer materials was identified. In developing the scale preventing and removing technology, a silica recovering device capable of treating hot water at 0.6 ton per hour as maximum was fabricated, and the site tests were performed by using cation-based coagulant. (NEDO)

Fiscal 1997 report on the results of the introductory R and D of the New Sunshine Project under a consignment from NEDO. Introductory R and D of the supercritical fluid use technology; 1997 nendo `New Sunshine keikaku` sendo kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chorinkai ryutai riyo gijutsu sendo kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The R and D of chemical reaction using supercritical fluids started in fiscal 1997. In the R and D of solvent reaction, as the research on polymer decomposition with supercritical water, studies were conducted of the mechanism of conversion reaction to chemical materials, cleavage mechanism of stable chemical bonds, and synthetic reaction in the supercritical state reaction field. In the research on oxidation reaction, as the study of complete oxidation in supercritical water for high efficiency energy recovery, studies of complete oxidation of liquid fuels, and complete oxidation of solid fuels. In the research on hydrogenation, studies of lightening of heavy oil in supercritical water, etc. In the R and D of the basic technology, studies of corrosion mechanism of metals in supercritical water, construction of the basic framework for technical database of supercritical fluids, etc. In the survey of technical trends and new research themes, the introductory R and D of element technology, etc. were conducted, and the results were described of the survey of technical trends and new research themes and the trend survey of overseas technology. 314 refs., 87 figs., 81 tabs.

FY 1998 annual report on the preliminary research and development of techniques for developing resources from gas-hydrate. Studies on gas-hydrate exploration, excavation techniques, methods for assessing environmental impacts, and gas hydrate handling systems; 1998 nendo gas hydrate shigenka gijutsu sendoken kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no kenkyu kaihatsu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This R and D project is for the preliminary studies on development of the following 4 types of techniques for developing resources from gas-hydrates (GH): (1) gas-hydrate exploration, (2) excavation techniques, (3) methods for assessing environmental impacts, and (4) gas hydrate handling systems. The FY 1988 R and D results are described. For gas-hydrate exploration, the methods for analyzing inorganic ions and trace quantities of elements, which are necessary for accurately estimating the offshore GH around Japan, are established; and case studies are conducted for methods of predicting GH deposit forming mechanisms, and stability fields of GH, based on terrestrial heat flow and seismic data. For excavation techniques, GH decomposition rate is analyzed using a laboratory system which reproduces conditions of excavation of GH layers. For methods for assessing environmental impacts, a geo-hazard predicting model is established, to study ground displacement and gas leakage sensing systems and data transmission systems to cope with the hazards. For gas hydrate handling systems, an overall system is studied, and storage and transportation systems are outlined. (NEDO)

FY 1999 R and D project on the global environmental industry technology. Report on the results of the R and D on the catalytic hydrogenation use CO2 fixation/effective utilization technology; 1999 nendo sesshoku suisoka hanno riyo nisanka tanso seika hokokusho. Koteika yuko riyo gijutsu kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of reducing CO2 emitting together with the consumption of fossil fuels, study was conducted on the use of CO2 by converting it to chemical substances such as methanol, etc., and the FY 1999 results were outlined. In the development of the CO2 separation membrane technology, data were obtained on effects of scaling-up by module with a membrane area of 4.9m{sup 2} and on design conditions. Further, in the experiment using mock exhaust gas, it was confirmed that the performance had been kept up for 3,000 hours or more. In the development of catalytic hydrogenation technology, the basic data for enlargement were accumulated. Moreover, the activity stabilized about 18,000 hours was confirmed, and the catalytic life was estimated at more than 3 years. In the development of large quantity hydrogen production/supply technology, assembly/operation of 7,500cm{sup 2} x 6 electrolytic cells were conducted, and it was confirmed that the hydrogen production capacity per cell was 3Nm{sup 3}/h. The final target for enlargement was achieved. In the study of the total system, the conceptual design was made for 'high concentration CO2 containing natural gas use CO2 recovery utilization system,' and 'biomass resource use methanol synthesis system.' (NEDO)

FY 1999 R and D project on the global environmental industry technology. Report on the results of the R and D on the catalytic hydrogenation use CO2 fixation/effective utilization technology; 1999 nendo sesshoku suisoka hanno riyo nisanka tanso seika hokokusho. Koteika yuko riyo gijutsu kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of reducing CO2 emitting together with the consumption of fossil fuels, study was conducted on the use of CO2 by converting it to chemical substances such as methanol, etc., and the FY 1999 results were outlined. In the development of the CO2 separation membrane technology, data were obtained on effects of scaling-up by module with a membrane area of 4.9m{sup 2} and on design conditions. Further, in the experiment using mock exhaust gas, it was confirmed that the performance had been kept up for 3,000 hours or more. In the development of catalytic hydrogenation technology, the basic data for enlargement were accumulated. Moreover, the activity stabilized about 18,000 hours was confirmed, and the catalytic life was estimated at more than 3 years. In the development of large quantity hydrogen production/supply technology, assembly/operation of 7,500cm{sup 2} x 6 electrolytic cells were conducted, and it was confirmed that the hydrogen production capacity per cell was 3Nm{sup 3}/h. The final target for enlargement was achieved. In the study of the total system, the conceptual design was made for 'high concentration CO2 containing natural gas use CO2 recovery utilization system,' and 'biomass resource use methanol synthesis system.' (NEDO)

Research and development of system to utilize photovoltaic energy. Study on large-scale PV power supply system; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyo energy kyokyu system no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on large-scale PV power supply systems in fiscal 1994. (1) On optimization of large-scale systems, the conceptual design of the model system was carried out which supposes a large-scale integrated PV power generation system in desert area. As a result, a pair of 250kW generation system was designed as minimum one consisting power unit. Its frame and construction method were designed considering weather conditions in the inland of China. (2) On optimization of large-scale transmission systems, as large-scale power transmission systems for PV power generation, the following were studied: AC aerial transmission, DC aerial transmission, superconducting transmission, hydrogen gas pipeline, and LH2 tanker transport. (3) On the influence of large-scale systems, it was estimated that emission control is expected by substituting PV power generation for coal fired power generation, the negative influence on natural environment cannot be supposed, and the favorable economic effect is expected as influence on social environment. 4 tabs.

Fiscal 1999 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Development of environmental protection oriented technology for effectively utilizing waste paper; 1999 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Kankyo hozengata no koshi no yuko riyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The effort aims to use low grade waste paper out of various grades of waste paper, whose recovery does not make good progress, as a raw material for the development of value-added, commercially competitive products and to contribute to the enhancement of waste paper recovery. A dry pulverization method less polluting the environment and not requiring a drying process is established, and types of waste paper and optimum conditions for their pulverization are made clear. A molding system using a steam injection method capable of atmospheric pressure control is established, and this enables the molding of pulverized waste paper not only into flat boards but also into corrugated boards. It is found that water contained in the waste paper alone produces a result similar to that expected from steam injection. A partitioning board is produced from waste paper, and it is found to be near the conventional product in terms of noise absorption. Old newspaper and corrugated cardboard are pulverized and an air filter is developed, which is similar to the conventional product in terms of operating efficiency and life. Waste paper is carbonized, and then charcoal with more pores than the conventional charcoal is produced. The porous charcoal is found to be usable in vegetable beds. (NEDO)

FY 2000 report on the survey to support the R and D on the development of the coal/natural gas use CO2 recovery/utilization technology; 2000 nendo sekitan tennen gas katsuyogata nisanka tanso kaishu riyo gijutsu no kaihatsu ni kansuru kenkyu kaihatsu shien chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In this study, technology to rationalize energy utilization is developed by which CO2 is efficiently converted into methanol which is the next generation liquid fuel by reacting CO2 with coal, natural gas and steam using solar heat. Together with this study, survey/study are conducted of the trend of the related element technology and the total system technology, trend of the competitive technology, study of comparison with the competitive technology, economical efficiency, possibility of the commercialization, etc. In this report, in Chapter 1, summarized are the trend of the R and D which each country conducts with the aim of using abundant solar energy in the Sun Belt and the trend of other R and D of energy utilization in each country. In Chapter 2, the paper describes the technology that Japan is now developing and the developmental trend of the related technology. In Chapter 3, the methanol supply/demand balance and the related researches were arranged. The most important points in future commercialization of the said technology are the establishment of technology and the economical efficiency. (NEDO)

FY 1998 'The New Sunshine Project' leading R and D. Report on the results of the leading R and D of supercritical fluid utilization technology; 1998 nendo 'New Sunshine Keikaku' sendo kenkyu kaihatsu. Chorinkai ryutai riyo gijutsu sendo kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The paper reported the FY 1998 achievement of the supercritical fluid utilization leading R and D which started in FY 1997 on a 3-year plan. In the R and D, solvolysis reaction, oxidation reaction and hydrogenation reaction were taken up in the chemical process using supercritical fluid. In the study of solvolysis reaction, the basic data were obtained on decomposition conditions of thermoplastic and thermosetting plastics in supercritical water. Further, concerning the synthesis of environmental friendly type carbonate using CO2, a conversion rate of almost 100% was obtained. About the oxidation reaction, conditions were found out for burning low grade coal in supercritical water without emitting acid gas. This is considered to lead to a possibility of the supercritical water power generation. Relating to the hydrogenation reaction, a study was made on lightening technology of heavy distillate using supercritical water, and the conditions for effective emission of methane and hydrogen were found out. As to the base technology, a study was made of metal materials with high corrosion resistance against supercritical water. (NEDO)

Report on achievements in fiscal 1999 on research and development of an intellectual base creating and utilizing technology. Research and development of a high-efficiency human body measuring device; 1999 nendo chiteki kiban sosei riyo gijutsu kenkyu kaihatsu seika hokokusho. Kokoritsu jintai keisokuki no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes the achievements in fiscal 1998 on developing a high-efficiency human body measuring device. Object building with high compatibility is requested in recent years, and a high-precision and high-efficiency measuring device for three-dimensional human body shape data is demanded. The ultimate target for the device is high-precision measurement of about 1 mm in about one second which is the time for human being capable of staying immovable. In association with proliferation of product designing by using a computer, the needs for data handling on computers are increasing sharply in industries. Proposals have been made by ISO and CEN on the standards for morphological characteristics of human being, inducing progress in international standardization of human body size and shape data. Structuring a database is also planned on three-dimensional shape data mainly in the U.S.A. The Human Life Engineering Research Center is studying development of a measuring device to measure human body types and sizes at high speed and accuracy. The device combines three-dimensional measurement by using an optical method with high-performance computerized image processing. The measuring device is supposed to be capable of outputting the measurement results as the size and three-dimensional shape data, so that the results can be applied to product designing quickly. (NEDO)

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 5. Development of hydrogen transport/storage technology (development of tanker for liquid hydrogen); Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 5. Suiso yuso chozo gijutsu no kaihatsu (ekitai suiso yuso tanker no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

As a part of the WE-NET project, the tanker for liquid hydrogen transport was studied. In fiscal 1996, some experiments and numerical analyses were proposed which are necessary to solve technological issues extracted in fiscal 1995 for heat insulation structure. The issue was roughly classified into vacuum and non-vacuum insulation, and their basic functions and required performance were arranged. Boil-off rate of 0.2-0.4%/d was targeted. The insulation system which applies polyurethane form (PUF) to tank surfaces and injects atmospheric N2 gas into the surrounding hold space, could achieve the targeted insulation performance by PUF of 1m in thickness. The system of vacuum panel insulation and atmospheric N2 gas injection into a hold space required the panel of 500mm in thickness because of the large effect of metallic outer panel material. The system of vacuum hold and PUF panels was faced with the essential issue for realizing and maintaining vacuum hold. The super insulation system featured by layered insulation materials and vacuum layer spaces was also strongly affected by degree of vacuum. 23 figs., 8 tabs.

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 5. Development of hydrogen transport/storage technology (development of storage facility for liquid hydrogen); Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 5. Suiso yuso chozo gijutsu no kaihatsu (ekitai suiso chozo setsubi no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

As a part of the WE-NET project, the storage facility for a large amount of liquid hydrogen (LH) was studied. Gasification loss caused by heat input of LH delivery pumps was studied for liquefaction and power generation bases assuming an pump efficiency of 70%, and the total heat and mass balance such as interface conditions for calculating the amount of boil-off gas was reviewed. The target storage capacity of 50,000m{sup 3} was reasonable, however, the performance of loading arms should be examined. The capacity around 5,000m{sup 3} of coastal localized bases was reasonable for control delivery loss caused by coastal tanker or LH container system to 2.6%. The capacity of 500m{sup 3} was suitable for inland bases, resulting in the loss of 1.2%. The concept design of the storage tank of 50,000m{sup 3} extracted confirmation of low-temperature characteristics of adiabatic materials and structures, and development of leakage inspection technology and vacuum holding technology as issues. The concept design of the underground storage tank showed that the material specifications for LNG ones are applicable to it by using proper adiabatic structures. 4 refs., 72 figs., 27 tabs.

Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 5. Development of hydrogen vehicle system; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 5. Suiso jidosha system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research result on the safety of hydrogen absorbing alloy tanks for hydrogen vehicle systems and the measuring method of a fuel consumption rate of hydrogen fuel cell powered vehicles. In the impact rupture test of (mini-scale) hydrogen absorbing alloy tanks, the impact 3-point bending test result by drop weight showed no ignition caused by impact and friction energy acting on hydrogen released by rupture of tanks, and the necessity for taking spontaneous ignition of alloys due to fuel leakage into account. The experiment result on deformation and rupture of alloy tanks caused by expansion and contraction of crystal lattices due to hydrogen absorption and desorption showed relatively large deformation due to grain fining only within earlier 10 cycles, and no cracks nor other defects even after 1000 cycles. In the measurement of a fuel consumption rate of hydrogen fuel cell powered vehicles, the study result on flow rate measurement method, full tank method, electric current method, hydrogen balance method and oxygen balance method showed that the electric current method is most simple, accurate and practical. (NEDO)

Fiscal 1998 R and D project on global environmental industrial technology. Research result report on DNA analysis and information processing technology for photosynthesis microorganisms (Development of CO{sub 2} fixation and effective use technology by using bacteria and algae); 1998 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Kogosei biseibutsu nado DNA kaiseki joho shori gijutsu no kenkyu (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the fiscal 1998 research result on DNA analysis and information processing technology for photosynthesis microorganisms. On the study on DNA analysis technology by triple-strand formation method, as the comparison study result of a READ method, stable triple- strand formation method and hairpin method, a READ method showed the highest triple-strand formation efficiency for target DNA. On the study on accurate separation technology of specific genes, establishment of protocols was promoted for solid-phase probe technology, subtract technology and leveling technology. On the study on DNA microarray analysis technology by high-efficiency hybridization method, the analysis technology of genes by hybridization method using DNA chips is under investigation. In addition, the high- efficiency analysis technology of specific DNA segments by using an affinity sensor, and the high-accuracy cloning technology for DNA with altered primary structure were also studied. (NEDO)

Industrial technology research and development project for global environment in fiscal 1998. Report on achievements in research and development of technologies for fixation and effective utilization of carbon dioxide by utilizing bacteria and algae; 1998 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Microorganisms are cultivated industrially in a great quantity to fix CO2 at efficiency higher than that of photosynthesis in natural world to develop technologies to re-utilize them as resources. This paper describes achievements in fiscal 1998. Existing strain samples of photosynthesized bacteria and micro-algae were screened to continue discussions on optimal culture conditions, and evaluation on properties. Genes that provide Chlorella with antibiotic resistance were introduced to have performed evaluation on function manifestation, and acquired enzymatic genes of unsaturated {omega} 3. Using green algae as the object, reduction in the processing time has resulted in acquiring a large number of fused cell colonies. Discussions were given on conditions to breed photosynthesized bacteria and fix CO2. Structural analyses were performed on CA protein as an enzyme related to take CO2 into living organisms, and on genes. Developments were carried out on a photosynthesizing bio-reactor and useful substance producing technologies on a continual basis. A 200-liter scale light collection type bio-reactor improved the fixing capacity by 30% in Chlorellas by changing the culture medium. The direct light receiving panel type bio-reactor can utilize even scattered light, with its fixing capacity per installation area exceeding the target. Fundamental data were acquired with Chlorellas on utilizing feeds, fertilizers and building materials. (NEDO)

Report of a project for the technical development of the environmental preservation and resource effective utilization system in fiscal 1995; 1995 nendo kankyo hozen shigen yuko riyo system gijutsu kaihatsu jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper outlined the present situation of industrial waste all over Japan and the present situation of industrial waste of large urban areas where it is most difficult to secure places for the final disposal, and conducted an analysis on the present and future amount of final disposal waste. According to the literature from the Ministry of Health and Welfare, `research report on the discharge/treatment situation of the industrial waste` and `research results of administrative organizations for industrial waste,` the situation of final disposal from the past to the present was outlined and analyzed to study the future trend. Out of the administrative divisions of Japan, four divisions, which are all typically called large urban areas, were selected, and the situation of industrial waste in large urban areas was outlined and analyzed according to the questionnaire survey and the literature on industrial waste obtained from each administrative division. The survey by the Ministry of Health and Welfare indicated that the volume of the industrial waste discharged from the whole country amounted to approximately 400 million tons in fiscal 1992. However, helped by the improving recycling of waste construction materials, the amount of final disposal around 2000 is presumed to be less by 20% or so than that in 1992. 58 refs., 5 tabs.

Next-generation coal utilization technology development study. Environmentally-friendly coal combustion technology; O2/CO2 combustion technology; Sekitan riyo jisedai gijutsu kaihatsu chosa. Kankyo chowagata sekitan nensho gijutsu (sanso nensho gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

For the purpose of developing combustion systems in which environmental pollutants are less emitted from coal-fired boilers, conducted in fiscal 1994 were a study of load followability of oxygen producing equipment, and element and basic tests on oxygen combustion systems. Dynamic simulations were made to confirm load followability of low-purity oxygen producing equipment. Further, a test was made on starting time of oxygen producing equipment. As a result of the simulation, favorable load followability was confirmed except for some of the process. The width of variation of the product oxygen purity was {plus_minus} 0.7% at maximum. In the element test on oxygen combustion systems, an experiment on the oxygen combustion using pulverized coal was conducted to study heat collection characteristics of furnace and response to multi-kind of coal. A study of balance of S content, experiments on characteristics of crushing/transporting pulverized coal, etc. were added. There were seen no peculiar differences in CO2 transport and air transport. 216 figs., 31 tabs.

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 4. Development of hydrogen production technology; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 4. Suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper describes development of hydrogen production technology as a part of the WE-NET project. For the solid polymer water electrolysis method higher in efficiency and lower in cost than the previous methods, 5 companies have developed element technologies for improving electrolysis cells and synthesis technologies of hot solid polymer electrolyte based on each proper catalyst electrode production method. In fiscal 1996, the initial study on large-scale systems by middle laboratory cells was made as well as improvement of electrolysis performance by small laboratory cells and endurance tests. Among the previous methods such as a hot press method (bonding of an ion exchange membrane to an electrode), an electroless plating method (preparation of porous surface onto a membrane electrode assembly), a zero gap method (preparation of high-efficiency high-current density cells), and a sintered porous electrode method (carrying of the mixture of catalytic powder and ion exchange resin-dissipated solution onto sintered metallic porous electrode surface), the former two methods were adopted for development of bench-scale cells as effective promising methods. 192 refs., 183 figs., 108 tabs.

FY 2001 report on the results of the development of the hydrothermal utilization power plant, etc. Development of collecting technology for deep geothermal resources (Development of drilling technology for deep geothermal resources); 1992 - 2001 nessui riyo hatsuden plant tou kaihatsu sokatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu - Shinbu chinetsu shigen kussaku gijutsu no kaihatsu (2001 nendo seika hokokusho bessatsu shiryo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the purpose of developing deep geothermal resources, development of 'drilling technology of deep geothermal resources' was made from FY 1991 to FY 2001, and the results were summarized. As to the development of bits, the bit that can be used for 30 hours or more at a temperature of 250 degrees C was developed, and the demonstrative test was made in FY 1997. Relating to the development of the high temperature use drilling mud, the mud that can be used at a temperature of 350 degrees C was developed, and the test using the actual well was conducted in FY 1997. Concerning the development of the high temperature use cement slurry, the cement slurry with specific gravity of 1.35 or below that can be used under the environment of a temperature of 350 degrees C was developed, and the hanging test of the specimen was made in the actual well in FY 1998. About the development of the high temperature use downhole motor, a prototype of 1/12 scale was fabricated in FY 1998, and the performance test at high temperature was conducted. As to the development of the high temperature use high strength cement slurry, a cement slurry with specific gravity of 1.50 or below and compressive strength of 19.61 MPa that is used under the environment of a temperature of 300 degrees C was developed, and the test on the long-term compressive strength was made in FY 2001. (NEDO)

Achievement report for fiscal 2000 on New Sunshine Project aiding program. Development of hot water utilizing power generation plant (Development of binary cycle power plant - development of system to detect well bottom information during geothermal well drilling); 2000 nendo nessui riyo hatsuden plant to kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu (Chinetsusei kussakuji koutei joho kenchi system no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

R and D has been performed on a system to detect well bottom information during geothermal well drilling (MWD) to identify items of well bottom information during drilling on a real time basis. This paper summarizes the achievements in fiscal 2000. This device measures and transmits to the ground surface the following items during geothermal well drilling at good accuracy under the mud water temperature of 200 degrees C: azimuth, inclination, tool face, bit load, bit torque, temperatures in the device, downhole temperature, and downhole pressure. The current fiscal year has performed improvement of the sonde, including decrease of the sonde length, electric power conservation, enhancement of anti-noise performance, and enhancement of operability. For the sonde performance evaluation, high-temperature test, long distance loop test, and vibration test were carried out. In addition, the experiment analyzing program (for noise processing) was improved. With regard to the well trajectory control aiding system and the well evaluation aiding system, an operation manual was prepared, entitled the 'MWD analyzing system'. Unification was attempted on the hardware of the ground surface detection device system and the analyzing system. (NEDO)

Fiscal 1997 report on the results of the New Sunshine Project subsidiary operation. Development of a geothermal water use power plant, etc. / technical development of the hot dry rock power generation system (development of electric technology); 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (koon gantai hatsuden system no gijutsu kaihatsu (yoso gijutsu no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of using hot dry rock energy to power generation, the R and D was continued of element technology of the hot dry rock power generation. In fiscal 1997, the construction of ground facilities, etc. for long-term circulation experiment was proceeded with to make data analysis for study of the experimental results. As for preparation for the long-term circulation experiment, design/fabrication/construction of experimental facilities were commenced, and review/fabrication of the monitoring system were conducted to strengthen the monitoring network of microearthquakes. In relation to the analytical research, using models connecting reservoirs and wells, relationships were studied among the distance between injection well and production well, production flow rate, and long-term thermal extraction characteristics of reservoirs. Further, to study structures of shallow/deep reservoirs at the Hijiori hot dry rock experimental field, re-determined were mechanism solutions of AE in deep hydraulic fracturing experiments, three well circulation tests, and preliminary circulation tests, and at the same time stress fields were studied. Fracture models were made and the simulation program was revised. 18 refs., 82 figs.

FY 1998 report on the project for development of hot water utilizing power generating plants and others, supported by New Sunshine Project. Development of extraction technologies and development of production technologies for the deep-seated geothermal resources; 1998 nendo nessui riyo hatsuden plant nado kaihatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the FY 1998 results of the activities for development of extraction and production technologies for the deep-seated geothermal resources, which are expected to contribute to increased geothermal power generation capacity. The program for the PTSD logging technology connects the S probe to PT probe, to simultaneously measure temperature, pressure and volumetric flow, producing the data of good quality even in a high temperature environment over 327 degrees C. Thus, possibility of the commercial system is confirmed. The D probe also produces a density calibration curve showing very good linearity, and operates normally in a high temperature environment of 406 degrees C. The program for the PTC monitoring technology conducts the field tests at Larderello, Italy, to confirm the sampler functions in a high temperature environment. The program for the tracer monitoring technology extracts promising tracers stable at high temperature from those for the liquid, vapor and liquid/vapor mixed phases. Silica is observed to be massively dissolved at 400 to 1,000mg/kg in the fluid under deep geothermal conditions. Scale precipitation rate is minimal for the first 21 days, but increases linearly with time thereafter. The experiments are also conducted for formation and prevention of the Fe-Si-based scales during the flushing period. (NEDO)

FY 2001 report on the results of the development of the hydrothermal utilization power plant, etc. Development of collecting technology for deep geothermal resources (Development of production technology for deep geothermal resources); 1992 - 2001 nessui riyo hatsuden plant tou kaihatsu sokatsu seika hokokusho. Shinbu chinetsu shigen saishu gijutsu no kaihatsu - Shinbu chinetsu shigen seisan gijutsu no kaihatsu (2001 nendo seika hokokusho bessatsu shiryo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For making effective/economical collection of deep geothermal resources, development was made from FY 1991 to FY 2001 of the 'drilling technology for deep geothermal resources' and 'production technology for deep geothermal resources,' and the results were summarized. As to the development of logging technology, the PTSD logging system was developed which can measure temperature/pressure/flow velocity/fluid density in geothermal well under the environment of temperature of 400 degrees C. Concerning the development of monitoring technology, development was made of the PT monitoring system that can make the long-term continuous measuring of temperature/pressure in deep geothermal observation well under the environment of temperature of 400 degrees C and of the C monitoring system that samples geothermal fluids at regular intervals to grasp changes in chemical component. Relating to the development of high temperature tracer monitoring technology, the following were conducted: extraction of high temperature tracer agent that can be used in geothermal reservoirs under the environment of temperature of 300 degrees C, development of simulator, and establishment of how to put tracer agent into the reservoir and how to analyze tracer agent. Further, the R and D were made of scale monitoring technology and scale prevention/removal technology. (NEDO)

Industry brief letter; Kasupikaioki sekiyu koku kaihatsu sekiyu shigen kaihatsu nado sannyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-02-01

4 companies of Petroleum Resources Development, Indonesia Petroleum, Teikoku Petroleum an Itochu Petroleum Development will sign petroleum exploration and development contract in petroleum mining property offshore of Caspian Sea with Azerbaijan National Petroleum Company, Sokar Company. In another mining property, Mitsui group reached conclusion with Sokar Company in mining right. Resource development competition between existing international petroleum majors and Japanese petroleum companies around Caspian Sea may be further intensified. (translated by NEDO)

Fiscal 1996 report on the results of the R and D of technology of high-level treatment/effective use of domestic/industrial wastes, etc. (for public); 1996 nendo Shin Energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku seikatsu sangyo haikibutsu shori yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the purpose of reducing environmental loads of waste and effectively using resource by waste recycling, a study was conducted of high-level treatment/effective use technology for domestic/industrial wastes, etc. The paper reported the results of fiscal 1996. In the EcoCement producing technology using the synthetic urban type waste, EcoCement with stable quality was obtained using sewage sludge and industrial waste as raw materials. In the specified freon decomposition disposal technology, an experiment was carried out on durability, etc. of the processing unit. In the high speed/reduced smell biological garbage disposal technology, technology of fermenting disposal, etc. were established, and at the same time technology of making garbage compost was developed. In the technology to manufacture environment friendly type plastic containers, etc., a degradation behavior was grasped of degradable plastics in the compost. In the spread type waste plastic/thermal recycle technology, studied were a system to collect waste and a system to make waste solid fuel. Technology to recycle coolant freon was studied. 14 refs., 261 figs., 137 tabs.

Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 7. Development of hydrogen supply station; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu seika hokokusho. Task 7. Suiso kyokyu station no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research result on element technologies and system technology for hydrogen supply stations. In 1999, study was made on the total system of hydrogen supply stations, and basic specifications and total designs were studied for such main component systems of hydrogen supply stations as hydrogen production equipment with a reformer of natural gas, polymer electrolyte water electrolyzer hydrogen supply system, hydrogen absorbing alloy tank, and hydrogen dispenser unit. From the study result on the optimum operation condition of the hydrogen production equipment, a S/C (ratio of steam/mol of material carbon) of 2.5, reforming temperature of 700 degrees C, recycling gas ratio of 0.21, and air-fuel ratio of 1.3-2.0 were obtained. In the study on optimum hydrogen absorbing alloy, LaNi{sub 5} alloy system with Mn as additive were selected. For the polymer electrolyte water electrolyzer hydrogen supply station, the basic specification of a total system, and the remote control system of the station were studied and established. R and D themes in the future were also presented. (NEDO)

Fiscal 1993 achievement report. International Clean Energy Network Using Hydrogen Conversion (WE-NET) technology (Subtask 8 - Development of hydrogen combustion turbine - Development of main accessories); 1993 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) (Subtask 8. Suiso nensho tabin no kaihatsu - Shuyo hokirui no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

In the first fiscal year 1993 of the project, surveys were conducted about current technologies relative to cold energy-utilizing oxygen production equipment and high-temperature heat exchangers for the development of main accessories for a hydrogen combustion turbine plant. Kobe Steel, Ltd., conducted surveys about very low temperature heat exchangers and cold energy utilization technology used in facilities for gasifying liquid hydrogen or liquefied gas. Daido Hoxan, Inc., in its research on the possibility of air separator performance enhancement through liquid hydrogen cold energy application, studied reduction in power unit requirement, stable power supply responding to changes in load, safety measures, and so forth. Toshiba Corporation conducted surveys and studies about heat conduction improvement techniques and about the type, structure, and materials for heat exchangers for the embodiment of a high-temperature heat exchanger excellent in performance and high in structural soundness. Mitsubishi Heavy Industries, Ltd., aiming to establish basic technologies for heat exchangers, studied efficiency enhancement with low pressure loss, improved hygroscopic moisture removing function, and new materials utilization for achieving high-temperature capability. (NEDO)

Comprehensive research concerning the development of effective utilizing techniques of biological resources (large scale research out of the framework). Seibutsu shigen no koritsuteki riyo gijutsu no kaihatsu ni kansuru sogo kenkyu (ogata betsuwaku kenkyu)

Energy Technology Data Exchange (ETDEWEB)

1991-10-25

This paper is a research report in which the cultivated production of forest resources, the development to useful substances and the systematization to take the root in a region were studied. The distribution maps of biological resources on respective woodland systems: that is, the nationwide distribution maps of the amount of resources in Japan as to the broadleaf trees in private forests and national forests, the available amount and kinds of tree were prepared. As for the establishment of cultivation technique of the super-short deforestation forest, that is, pursue of wooden growth to the maximum limit, the superior clone 26 system was selected from the willow group through the research of wooden cultivation and the clone which showed the maximum yield reached 24t/ha every year. As for the material preparation technique due to microbial enzymes, that is, the creation and breeding of fungi which have the high lignin decomposition power, a stock of fungi which has the high lignin decomposition power and the decomposition selectivity was created by the cell fusion and the UV (ultraviolet ray) radiation treatment. As for the use of effective components in wooden resources, many useful characteristics could be detected by applying the boiling, bursting and ozone treatment. As for the mushroom cultivation through the application of unused tree kinds, a new kind of mushroom for food service was selected to clarify the possibility of fruit body formation. The development of a new material from conifers is promising. 1 tab.

FY 1998 annual report on the survey on development, introduction and promotion of urban type multipurpose geothermal utilization techniques; 1998 nendo toshigata tamokuteki chinetsu riyo gijutsu no kaihatsu, donyu, sokushin ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Introduction of geothermal heat pump systems, which depend on temperature differential, is investigated for urban areas, which have large energy demands. Results of the surveys on the current situations of geothermal heat pump (GHP) systems indicate that they have already numbered 300,000 units in USA and totaled more than 50,000 units in Switzerland and Northern European countries, and that they are increasing at an annual rate of higher than 10%. The results also indicate that introduction of these systems are well feasible in Japan, which generally has better topographical conditions than American and European countries, and the GHP system with vertical ground heat exchanger is investigated for its topographical and environmental considerations. These systems could annually abate approximately 52 million tons of CO2 (4.3% decrease), if disseminated to all households. They are also expected to help control the heat island phenomenon, and reduce peak power consumption. The technological problems to be solved before these systems are massively disseminated including development of small scale drilling rigs and preparation of drilling manuals. System standardization and introduction of subsidy systems are also needed to massively disseminate these systems. (NEDO)

Development of hydroponic system using agricultural waste. 2. Utilization of ozone for sterilization of nutrient solution; Suiko saibai ni okeru haikibutsu riyo gijutsu no kaihatsu. 2. Ozone ni yoru baiyoeki sakkin ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Terazoe, H; Yoshihara, T; Nakaya, K [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1995-08-01

Discussions were given on a sterilizing effect of ozone on Fusarium bacteria in hydroponic culture, and its effect on components in the culture solution. In an experiment, dry air with O3 concentration of 3.5 ppm was sent into aqueous solution inoculated with Fusarium bacteria at a flow rate of 5 liters per minute. The Fusarium bacteria was sterilized nearly completely in about five minutes. No change was observed in pH, EC and dissolved oxygen concentration of the O3-treated culture solution. However, iron and manganese among the soluble components have been oxidized by O3 and precipitated, hence these components must be added after the O3 treatment. In spinach culture performed on a culture medium inoculated with Fusarium bacteria, ozone water containing dissolved O3 at 0.8 ppm was flown into a urethane foam medium and vegetable roots. This treatment has resulted in reduction of the number of strains occurred with a wilt symptom below that in the section flown with distilled water. The spinach has grown normally without showing an effect of the ozone water. 15 refs., 10 figs., 3 tabs.

Technological development report for fiscal 1993 on the woodwaste thermolysis/gasification technology and generated gas utilization technology; 1993 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The project is a joint effort of Japan and the Philippines to develop a thermolysis/gasification system, in which woodwaste now remaining unexploited in the Philippines is subjected to thermolysis/gasification and the resulting gas is used in a gas engine for the generation of electric power, in a 5-year period beginning in fiscal 1990. In this fiscal year, element technology verification tests are conducted, components of a demonstration plant are manufactured, and procurement is made as required, which completes all the tasks allotted to this fiscal year. All the constituents of the said demonstration plant fabricated or procured since fiscal 1991 are packed up and forwarded to Industrial Technology Development Institute (ITDI) of the Philippines, and engineering guidance is extended and test operations are carried out at the site of plant installation. In line with the said endeavors, on-site investigations are performed and researches are conducted together with ITDI scientists concerning the construction work and element technology confirmation. On the other hand, the Philippine side performs the second phase of civil engineering and construction carried over from the first phase. The demonstration plant is completed, adjustment and test operations are carried out, which means that the project is in progress as initially scheduled. (NEDO)

Achievement report on research and development (1st phase) of direct iron making by use of high-temperature; Koon kangen gas riyo ni yoru chokusetsu seitetsu no kenkyu kaihatsu (daiikki) ni kansuru hyoka hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-02-01

Efforts are put into the study of direct iron making for use in a closed system where heat energy from a multi-purpose high-temperature gas furnace expected to be developed in the near future will be utilized for iron making. The researches, carried out for the establishment of technologies necessary for designing, building, and operating a pilot plant dimensionally suitable for connection to a 50MWt multi-purpose high-temperature gas furnace, cover the plant total system, a high-temperature heat exchanger, ultrahigh-temperature alloys, high-temperature insulating materials, a reduced gas generating unit, and a reduced iron making unit. When the effort is evaluated as a whole, it is found that the newly developed system is effective in preventing pollution, emitting but 0.1Nm{sup 3} of SOx per 1 ton of crude iron against the 0.4-0.9Nm{sup 3} emitted by a blast furnace/converter iron making mill. It is also found effective in reducing fossil fuel dependence and in enhancing energy source diversification. When it comes to energy conversion efficiency, furthermore, it is shown that the new system achieves a rate of 60% or more while only approximately 30% is attained by light water reactor power generation and approximately 40% by a high-temperature gas furnace. (NEDO)

Worldwide clean energy system technology using hydrogen (WE-NET). Interim report of the research and development in Phase 1; Suiso riyo kokusai clean energy system gijutsu (WE-NET). Daiikki kenkyu kaihatsu chukan seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

Large scale and effective utilization of renewable energy including hydroelectric power, photovoltaic power, and wind power which are abundant on the earth can contribute to the solution of global environmental issues as well as the release of energy demand and supply. Hydrogen can be produced from the renewable energy, and is converted, transferred and stored if necessary. Such hydrogen can be used in various fields for power generation, fuel for transport, and city gas. In order to establish the technology by which worldwide energy network can be introduced for wide range of fields, conceptual design of a total system has been conducted, and elemental core technologies have been developed. Conceptual design of a practical scale system (total system) including a wide range from production of hydrogen to its utilization has been conducted, and its constitution has been illustrated. In addition, the energy balance and cost of hydrogen have been calculated and analyzed as a trial. Hydrogen production technology, transport and storage technology, and hydrogen utilization technology are introduced as individual elemental technologies. Research results of innovative and leading technologies obtained in FY 1996 are reviewed. 80 figs., 56 tabs.

Fiscal 2000 research and development of technologies for intelligent infrastructure creation and utilization. Development of high-precision screening assay system for endocrine disrupting chemicals and construction of database; 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu. Naibunpi kakuran busshitsu no koseido screening shiken hoho no kaihatsu oyobi data kiban seibi

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development is carried out for the establishment of a system for assaying endocrine disruption now presenting itself as a hazard and for the application of the assay system to important chemicals and chemicals under development for the detection of presence of endocrine disrupting action in them. In this fiscal year, for the establishment of a reporter-gene assay system, cell characteristics were clarified through the determination of the expression sequence of the produced cell, the determination of the stable conservation period of the cell, and the study of the sustenance of activity. Studies were conducted, targeted at the stable supply of cells usable for high-throughput screening. Basic data were collected for the Hershberger assay being developed by OECD (Organization for Economic Cooperation and Development) and for the repeated administration test method for assaying thyroid hormone action by use of pubertal rats. For the assay of impact on environmental organisms, moreover, basic data were collected for the establishment of testing methods using fishes and amphibians. (NEDO)

Achievement report for fiscal 2000. Phase II research and development task-5 for hydrogen utilizing international clean energy system technology (WE-NET) (Development of hydrogen fueled automobile system); 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 5. Suiso jidosha system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for Task-5, the development of a hydrogen fueled automobile system. For a fast filling method using a hydrogen absorbing alloy as the fuel tank, a rare earth system, the Laves system, and a body-centered cubic system were selected to discuss filling time when the plate-fin system tank and the divided system tank are used. Either system was found capable of filling 80% of the effective hydrogen absorbing amount within 10 minutes, having achieved the target. Guidelines were obtained for the design aiding method by using the cooling water flow rates, temperatures, and simulations. In the safety assessment, even the spontaneously combusting alloy of Category 1 in the Fire Fighting Law did not cause ignition even if the tank was damaged and the alloy was discharged in the dropping/falling weight tests. It was inferred that the ignition temperature is not reached because of the self-cooling made when hydrogen is discharged from the alloy. In the fire resistance test, the tank temperature was found not to rise as long as hydrogen is discharged from the alloy. Since the temperature rise and damage could occur if the discharge has been finished completely, discussions are required on materials and the soluble plug. Deformation may occur in the initial stage of the hydrogen absorbing and discharging cycles, but it would not occur after 5,000 cycles. (NEDO)

FY 2000 report on the results of the R and D of femtosecond technology. R and D of high intensity X-ray pulse use power generation facility monitoring system; 2000 nendo femto byo technology no kenkyu kaihatsu seika hokokusho. Kokido X sen pulse riyo hatsuden shisetsu monitoring system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This project aims at creating new industrial basement technology which supports the highly information-oriented society in the 21st century, conducts the R and D of technology to control the state of light and electron in the femtosecond time domain (10{sup -15} - 10{sup -12} sec), and establishes the basement technology which exceeds the speed limit of the conventional electronics technology and also includes new functionality. Especially, in the R and D of the high intensity X-ray pulse use power generation facility monitoring system, the establishment is aimed at of the basement technology toward the realization of non-stop inspection of high speed moving objects of power generation facilities, etc. using femtosecond high intensity X-ray pulse generated in the interaction between femtosecond optical pulse and high density electron beam pulse. In this fiscal year, femtosecond X-ray was successfully generated. The pulse width of X-ray: 400fs, the wavelength: 6 angstroms, the X-ray dose generated in one collision: 10{sup 4} photons/pulse or more, and the energy of electron beam colliding with laser optical pulse: 12 MeV. Moreover, developed were the laser amplifying system and the stabilized high power femtosecond laser system. (NEDO)

Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 10. Development of low-temperature materials; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 10. Teion zairyo no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the achievements in fiscal 2000 from the development of candidate low-temperature materials for liquid hydrogen transportation and storage (including mother materials and welds) for WE-NET. Evaluation tests were performed on material properties (mechanical properties, low-temperature embrittlement, and hydrogen embrittlement sensitivity) under room temperature and low temperature regions including liquid hydrogen atmosphere. Low temperature toughness of welds was assessed particularly to identify characteristics of different welding methods developed newly for improvements. The stainless steels and the mother materials of aluminum alloy selected as the candidates have sufficient characteristics even under the liquid hydrogen atmosphere, but the welds have lower low-temperature toughness, requiring improvement. For the stainless steels, since the amount of {delta} ferrite in welds affects greatly the low-temperature toughness, adoption of complete austenite type welding metal is effective. The reduced pressure electron beam welding method can enhance drastically the low-temperature toughness of stainless steel. For the aluminum alloy, it can be one of the alternatives to use an alloy system with composition of high low-temperature toughness. The friction stir welding method for the aluminum alloy was found to provide extremely high low-temperature toughness, which can be evaluated as a new welding method. (NEDO)

Report on achievements in fiscal 1999 on the project for research and development of an intellectual base creating and utilizing technology. Research and development of standard substances related to polymers; 1999 nendo chiteki kiban sosei riyo gijutsu kenkyu kaihatsu jigyo gyomu seika hokokusho. Kobunshi ni kansuru hyojun busshitsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes the achievements in fiscal 1999 on researching and developing standard substances related to polymers. Investigations were performed on polystyrene with average molecular weights of 300 to 2,000 being the standard polymeric substance as the primary subject, and polycarbonate with molecular weight of about 300,000 as the secondary subject. Development was executed on the fundamental technologies related to chromatographic conditions for separation to acquire polymers without molecular weight distribution or with very little distribution (single dispersion), and sampling conditions for the sampling chromatography. Uniform polymers were used as the primary calibration standard substance to have developed the fundamental method and the fundamental conditions to value exactly the average molecular weight values such as in the single dispersion test. Polyvinyl chloride (PVC) was taken up as the valuing material as a polymeric material with less secular change being the indispensable element as the standard substance, and capable of being stably supplied. Round robin tests were performed by 16 testing organizations on the tensile elasticity specified in ISO10350 in accordance with the international standard guide 35 to have valued the standard substances. Variance in property values of PVC sheets was analyzed, and the standard deviation was verified. (NEDO)

Achievement report for fiscal 1998 on business auxiliary to New Sunshine Program. Hot water-aided power generation plant development (Development of deep-seated geothermal resources exploitation technology and development of deep-seated geothermal resources excavating technology); 1998 nendo new sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu, shinbu chinetsu shigen kussaku gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the general exploitation scheme, technological information is collected about cement overseas, DHM (down hole motor), etc. In the development of heat-resistant durable bits, an improved version of the 350 degrees C real bit manufactured in fiscal 1997 undergoes a test in a real bore, and is evaluated for its general performance. In the development of high-temperature cement slurries, the ultralow specific gravity cement slurry for casing cement developed in fiscal 1997 is subjected to evaluation. It is examined by chemical analysis and powder X-ray diffraction, and its fluidity, free water, rate of dehydration, and compression strength at 250 degrees C are measured. In a real bore test, a slurry of the optimum composition is prepared and then hardened, and the hardened body is kept exposed to geothermal environments for eight weeks. It is then found that the hardened body retains a compression strength of 70kgf/cm{sup 2}. In the development of a down hole motor, a scale model, real in diameter and shortened in length, is built of the motor section, and is tested in circulating water and oil at normal and high temperatures, and its behavior and performance are evaluated. (NEDO)

Fiscal 1997 report on the results of the New Sunshine Project subsidiary operation. Development of the geothermal water use power plant, etc. (development of the binary cycle power plant / development of the geothermal well MWD system); 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (binary cycle hatsuden plant no kaihatsu (chinetsusei kussakuji kotei joho kenchi system no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of improving efficiency and accuracy in geothermal well drilling, the development was conducted of an MWD (measuring while drilling) which detects borehole information in real time. In fiscal 1997, the following R and D were carried out. As to the downhole equipment, the actual well experiment on the sonde was conducted to confirm the basic performance. The design improvement, trial fabrication and experiment were conducted on mud pulse generating valve driving control equipment, bore hole signal processing unit and temperature correction circuit portion in the sonde. Concerning electronic parts, a heat resistance confirming test was conducted for data collection/assessment. Further, jigs were fabricated for tests to confirm working of each equipment. Relating to the ground equipment, conducted were improvement of the decoded program and betterment of the analytical system and interface. As to the development of the analytical system, data on depth were added to the azimuth/inclination obtained from MWD, which enabled indication of a well drilling tracing chart while drilling. 92 figs., 43 tabs.

Fiscal 1997 R and D project under a consignment from NEDO. R and D of the femtosecond technology (R and D of the monitoring system using high-intensity X-ray pulse for power plants); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Femto byo technology no kenkyu kaihatsu (kokido X sen pulse riyo hatsuden shisetsu monitoring system no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports the result on R and D of the femtosecond technology in fiscal 1997. Ultrahigh-speed electronic technology is indispensable for industrial basic technologies supporting the advanced information society in the 21st century. Control technology of photonic and electronic states in a femtosecond region is essential. In R and D of metrological technology using ultra-short light-pulses, study was made on generating and controlling technology for ultra- short light/electron beam pulses. Ti-sapphire mode-locked laser was prepared, and it was found that time-fluctuation of mode-locked laser pulses is measurable up to 100 femtosecond level. As measures against an instability of gain-switching semiconductor laser, light injection from the outside was effective. The stable directivity of laser beam was obtained by regenerative amplifier, while less temperature variation of an optical switch was necessary to stabilize energy. To generate femtosecond high-intensity X-ray pulse by collision of laser and electron beams, it was confirmed that sub- picosecond synchronization is possible by RF and picosecond laser synchronization circuit. 48 refs., 89 figs., 11 tabs.

Achievement report for fiscal 1998 on development of environmentally friendly high-efficiency energy utilization system. 2. Research of technology of effectively utilizing high-efficiency energy / research of optimum system designing technology; 1998 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu. 2. Kokoritsu energy yuko riyo gijutsu no kenkyu, saiteki system sekkei gijutsu no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

This 2nd volume deals with the transportation and storage of energy in the above-named research. In search of technologies for transporting exhausted heat from the industrial area to the urban section for consumers to utilize the heat for driving their air-conditioners and hot water supply systems, the decomposition and composition reactions of methanol are utilized for a long-range transportation system. The subjects taken up in this connection include the research and development of a methanol energy system, non-equilibrium high-efficiency methanol decomposition technology, multifunctional catalysts, and highly active/selective catalysts capable of promoting reversible endoergic/exoergic reactions. Research and development is also conducted of a high-efficiency heat pump technology using hydrogen-absorbing alloys, and such a pump will realize an air-conditioning system not dependent on chlorofluorocarbon. In the research and development of a long-range heat transportation system using hydrogen-absorbing alloys, a study is made of technologies of heat/hydrogen recovery, transportation, and utilization. (NEDO)

Development for environmentally friendly and highly efficient energy utilization system in fiscal 1998. Pt. 3. Research on highly efficient and effective energy utilization technology (Research on design technology for optimal system); 1998 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu. 3. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

This paper summarizes achievements during fiscal 1998 on researching part of the energy transportation and storage technologies, energy supply and utilization technologies, environmental load reducing technologies, and optimal system design in the 'research on highly efficient and effective energy utilization technology'. With regard to energy transportation and storage technologies, researches and developments were performed on a vacuum adiabatic transportation piping system, surfactants used for high-density heat transportation and high-density latent heat transportation technologies. In the field of energy supply and utilization technologies, researches and developments were carried out on a heat supply system using high-performance heat pumps capable of using multiple kinds of fuels, and a compression and absorption type hybrid heat utilization system. For the environmental load reducing technologies, research and development were performed on a power saving heat pump system utilizing natural coolant. In researching the optimal system design technologies, overall adjustment was made on the element technologies, whereas technological discussions and site surveys were executed by the committees at the same time. The latest achievements accomplished to date was published in a book. (NEDO)

Development for environmentally friendly and highly efficient energy utilization system in fiscal 1998. Pt. 1. Research on highly efficient and effective energy utilization technology (Research on design technology for optimal system); 1998 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu. 1. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

This paper summarizes achievements of the researches during fiscal 1998 on researching a highly efficient and effective energy utilization technology. With regard to technologies to recover and convert unutilized energies, a process simulator was developed, basic internal structure was discussed by experiments and simulation, and substance migrating and heat exchanging characteristics were identified by using partial testing devices. These researches and developments were performed for the waste heat reforming and recovering systems used in chemical plants. In developing a thermoelectric generation system using low calorie exhaust gases, thermoelectric power generating materials were developed, a powder manufacturing technology was developed, a thermoelectric conversion element bulking technology was developed, a thermoelectric power generation system using porous structures was simulated, development and concept design were carried out on system element technologies. In the research and development of the thermoelectric generation system using low calorie exhaust gases, advanced materials and modules were manufactured, the modules were evaluated, and power generation systems were researched. In addition, researches were performed on energy transportation, supply and utilization technologies, and on environmental load reducing technologies. (NEDO)

Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Development of systems for marine organism resources classification and utilization (Achievement report); 1998 nendo kaiyo seibutsu nado shigen no bunrui riyo system no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Genetic resources and databases involving microbes and the like were conserved and amplified for the reinforcement of biotechnology industries. In the maintenance of marine microalga culture collection, 16S rDNA sequences were determined for 120 strains of Cyanophyceae isolated by Marine Biotechnology Institute Co., Ltd., and databases were prepared containing the results of molecule classification, history of each strain, and pictures obtained using optical microscopes. In the maintenance of marine bacterium culture collection, methods for identifying by molecule classification bacteria separated from the sea were simplified and unified, and genera were identified for 776 strains. In the development of systems for classifying and conserving subtropical microbial resources, base sequences were analyzed for 14 strains of six kinds of microbes such as Aspergillus awamori conserved at Institute of Applied Microbiology of University of Tokyo. Other efforts included the enrichment of marine microalga collections, construction of an embryo bank system, advanced classification of microbes, and development of a DNA (deoxyribonucleic acid) analyzing system. (NEDO)

Hydrogen utilization international clean energy system technology (WE-NET). Subtask 8. Development of hydrogen combustion turbines (development of the main component devices such as turbine blades and rotors); Suiso riyo kokusai clean energy system gijutsu (WE-NET). Subtask 8. Suiso nensho turbine no kaihatsu (turbine yoku, rotor nado shuyo kosei kiki no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper described the result of the fiscal 1996 development relating to hydrogen combustion turbines, as one of the hydrogen utilization technologies, which have excellent environmentality and are expected of remarkably high efficiency. In the film cooling system of first-stage moving/stationary blades, the smaller the pitch of film pore is, the higher the mean cooling efficiency becomes, indicating 0.7 at maximum. As compared with the conventional shower head type, the metal temperature can be reduced 30-40degC. In the recovery type inner (convection) cooling system, by reducing the blade number, the consumption amount of coolant can be reduced 6% in stationary blade and 13% in moving blade, as compared with the result of the preceding year. In the element test of the hybrid cooling system, film cooling efficiency was actually measured by the porous module test equipment, and the result well agreed with the calculation result. In the water cooling system, studied were water (stationary blade) and vapor (moving blade) of the closed cooling structure for realization of a cycle efficiency of 60%. In rotor/disk cooling, analyses were made of seal characteristic grasp tests and characteristics of the rotor. The effect of deflection in the mainstream was small. Besides, proper value of the seal overlapping amount could be obtained. 6 refs., 368 figs., 55 tabs.

FY 1998 annual summary report on International Clean Energy Network Using Hydrogen Conversion (WE-NET) system technology. Subtask 8. Development of hydrogen combustion turbine and ultrahigh-temperature materials; 1998 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 8 (suiro nensho turbine no kaihatsu/chokoon zairyo no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Summarized herein are the materials designs/production and tests/evaluation results of heat-resistant materials, i.e., alloys, ceramic composites and carbon-based composites, which are expected to be applicable to the hydrogen combustion turbines. These have been studied since 1993, and this paper summarizes the overall evaluation results of the phase I program. The intermetallic compound as one of the candidate materials has a high-temperature strength in a range from 1200 to 1400 degrees C by optimizing elements added. However, no prospect is obtained for heat resistance at 1700 degrees C or more for the material not coated or cooled moderately. Each of the other candidate materials tested shows a bright prospect of applicability at the base material and specimen levels. The single-crystal superalloy for hybrid cooling structures has novelty in that it is free of Cr but incorporated with Si and Hf, showing approximately 10 degrees C higher heat-resistant temperature than CMSX-4. CMC and C/C are inherently excellent heat-resistant materials, and are attractive advanced composites, because they are expected to realize no-cooled blades at 1700 degrees C. (NEDO)

Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 8. Development of hydrogen production technology; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu seika hokokusho. 8. Suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was carried out to establish a hydrogen production technology in the electrolysis of water using the solid macromolecular electrolyte method expected to be more efficient and less costly than the conventional hydrogen production methods. In the development of large area electrolysis cell lamination, a lamination comprising ten 2,500cm{sup 2} cells was fabricated, and a value exceeding the target energy efficiency of 90% was achieved. In the fabrication of stacks for hydrogen service stations, a lamination of ten cell stacks of 1,000cm{sup 2} was built, which achieved energy efficiency of not less than 90% at the an electrolysis temperature of 100 degrees C. A hydrogen production plant conceptual design was prepared under the conditions of hydrogen generation amount: 10,000Nm{sup 3}/h, electrode area: 10,000cm{sup 2}/cell, current density: 2.5A/cm{sup 2}, operating temperature: 120 degrees C, cell voltage: 1.705V, total number of cells: 976, stack constitution: 122/stack, and the number of stacks: 8. The result of studies placed the plant construction cost at 2.18-billion yen including building and civil engineering costs, and the hydrogen production unit cost at 28.4 yen/Nm{sup 3}. (NEDO)

Fiscal 1997 survey report. Subtask 8 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (R and D of hydrogen combustion turbines/development of ultra-high temperature materials); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 8 suiso nensho turbine kenkyu kaihatsu chokoon zairyo no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the application to hydrogen combustion turbines, the R and D were continued of heat resistant alloys, ceramic composite materials, and carbonaceous composite materials. In the development of highly efficient super alloy single crystal materials, as to the single crystal alloy (Ni-5.3Al-0.5Ti-6.0Mo-4.8W-6.0Re) and an alloy made by adding 0.15%Si to the above alloy and an alloy made by adding 2.0%Hf to the above alloy, data on high temperature tensile property and creep rupture property were obtained, and it was confirmed that Hf added alloys were excellent in strength. Relating to the development of fiber reinforced ceramics, materials for trial fabrication were fabricated by the CVI method using SiC fiber, and the evaluation test was conducted to obtain the basic data. Besides, the following were carried out: study of coating for heat resistant alloy cooled blades, development of ceramic composite materials, development of ceramic multi-structure materials and analysis of fracture behaviors under the ultra-high composite environment, development of 3D fiber reinforced composite materials, development of technology to evaluate basic properties of ultra-high temperature materials, etc. 46 refs., 217 figs., 43 tabs.

Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 4. Development of motive power generation technology; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 4. Doryoku hassei gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for Task-4, the development of a motive power generation technology. The objective is to build a 100-kW class single cylinder hydrogen-argon circulating diesel system. For a hydrogen injection valve being the key to the system, development was made on the conventional hydraulic system with quick compression, expansion, and electronics control. Discussions were given on an exhaust gas condenser and a gas-liquid separator to handle gas mixture with low steam concentration. In order to assure the mechanical strength to deal with the argon working gas, super-chargers and expansion turbines were also discussed. When the hydrogen injection pressure is increased from 20 to 25 MPa in the basic test, the combustion speed has increased, and the indicated thermal efficiency has been improved. The same effect was obtained also when the oxygen/argon ratio was increased. Although the thermal loss increases if the oxygen/argon ratio is increased, the loss in the indicated thermal efficiency is compensated by the gain derived from increasing the combustion speed. When argon is used as the working gas, the temperatures in parts of the combustion chamber rise much higher than that in the case of a light oil diesel system. Therefore, discussions were given on materials and structures that can withstand elevated temperatures, and assessments and tests were performed on high-temperature lubricants. (NEDO)

Load leveling of the Tohoku Electric Power Co. Development of ice storage cold-water manufacturing unit/solid organic waste treatment equipment using midnight power for cold district; Tohoku Denryoku no fuka heijunka. Kori chikunetsu reisui seizo unit no kaihatsu, shin`ya denryoku riyo kanreichi muke kokei yuki haikibutsu shori sochi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-10-01

An ice storage cold-water manufacturing unit that can manufacture cold water at a stable temperature near 0degC by using midnight power and a solid organic waste treatment facility were developed. The high-speed melting of ice is required to stabilize the cold-water temperature. Therefore, experimental investigation was performed. A piece of flake-shaped ice whose surface area and storage quality are balanced was used. A system that melts ice using the melting tank installed outside an icebox, and a high-speed melting system of ice based on the mixing unit installed in a melting tank were also used together. In the validation test of a prototype for smaller food factories, the following was confirmed. Manufacturing of cold water at about 1degC, amount of cooled water, stability of output water temperature for a change in water temperature, and good storage of ice in an icebox. In the prototype developed for a solid organic waste treatment facility, satisfactory performance was confirmed for following. Temperature in a fermenter when wastes were put, moisture content in a fermenter, pH value, net loss when the refuse of fish is put, and saving of an electricity rate. 6 figs., 2 tabs.

Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. Investigative research on solar system (Development, investigation and research of solar heat utilizing system); 1998 nendo sangyoyonado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Solar system no chosa kenkyu (taiyonetsu riyo system no gijutsu kaihatsu chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective to prepare a strategic technological development program for solar heat utilization, evaluations and discussions were given on solar heat utilization from the viewpoints of 'utilizing applications', 'demand' and 'possibility of the proliferation thereof'. In the solar heat utilization, the cost rising in approximate proportion with scale of the heat utilization must be considered as one of the predestined conditions. What can be conceived as a means to enhance the economic performance by using engineering approaches would include heat storage, elementary technologies for transportation and the standardization thereof, and the scale economy on the production side in mass production. As a required step in which the series of favorable circulation of standardization to mass production, cost reduction and large quantity proliferation can be induced, it is appropriate to assume household use with high calorie unit price as the target. The household area covers room heating and hot water supply, in which the temperature level is much lower than in industrial use. In this area, a system may be established with a conception to use solar heat as the main heat source, and calorific power by fossil fuel as the supplementary heat source. Solar heat utilization may be considered utilizable in foodstuff factories and school lunch supply centers. (NEDO)

Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. Investigative research on solar system (Development, investigation and research of solar heat utilizing system); 1998 nendo sangyoyonado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Solar system no chosa kenkyu (taiyonetsu riyo system no gijutsu kaihatsu chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective to prepare a strategic technological development program for solar heat utilization, evaluations and discussions were given on solar heat utilization from the viewpoints of 'utilizing applications', 'demand' and 'possibility of the proliferation thereof'. In the solar heat utilization, the cost rising in approximate proportion with scale of the heat utilization must be considered as one of the predestined conditions. What can be conceived as a means to enhance the economic performance by using engineering approaches would include heat storage, elementary technologies for transportation and the standardization thereof, and the scale economy on the production side in mass production. As a required step in which the series of favorable circulation of standardization to mass production, cost reduction and large quantity proliferation can be induced, it is appropriate to assume household use with high calorie unit price as the target. The household area covers room heating and hot water supply, in which the temperature level is much lower than in industrial use. In this area, a system may be established with a conception to use solar heat as the main heat source, and calorific power by fossil fuel as the supplementary heat source. Solar heat utilization may be considered utilizable in foodstuff factories and school lunch supply centers. (NEDO)

Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 7. Development of hydrogen refueling station; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 7. Suiso kyokyu station no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the achievements in fiscal 2000 from the development of hydrogen refueling stand-alone stations for hydrogen fueled automobiles in the WE-NET. Supply capacity of practical size of 1/10, 30 Nm{sup 3} was selected as the object. For the natural gas reformed type hydrogen generator, discussions were given on design and manufacture of a reforming unit and a PSA device. The PCT diagram method was discussed to estimate the capacity of a hydrogen absorbing alloy type storing facility. Interface between fuel cell driven automobiles and the station was adjusted. For the solid polymer electrolyte water decomposition type, safety measures were discussed with a high-pressure filling system kept in mind. Detailed design was made on a water decomposing hydrogen generator. Fabrication was completed on the hydrogen absorbing alloy type storing facility, and verifications were given on the storage amount, hydrogen absorbing speed, and discharge capability. In the high-pressure refueling system, temperature rise was simulated at a pressure of 35 MPa. Refueling for ten minutes raised the gas temperature by 75 degrees C, and the container surface by 65 degrees C. Local temperature rise was forecasted in the actual work, which is a future discussion assignment. An outline method was discussed for the verification test. (NEDO)

Report on evaluation of research and development of direct steel-making using high-temperature reducing gas. Phase 1. Draft; Koon kangen gas riyo ni yoru chokusetsu seitetsu no kenkyu kaihatsu (daiikki) ni kansuru hyoka hokokusho (an)

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-01-01

Described herein is development of direct steel-making using high-temperature reducing gas. A light hydrocarbon fraction (boiling point: 230 degrees C or lower), produced by steam cracking of vacuum residua, is reformed into a reducing gas in the presence of steam, using heat to be supplied by a nuclear plant which produces high-temperature gases for various purposes. This reducing gas is then supplied to a plant for producing reduced iron. This project has established basic techniques for designing, constructing and operating a direct steel-making pilot plant, to be connected to a 50 MWt high-temperature gas test furnace. The closed iron-making system and greatly reduced SOx emissions to several fractions of the current level are some of the expected effects. The environmental impacts of the high-temperature gas furnace will be on a level with those associated with a light-water reactor. Cracking and gasification of vacuum residua, which has found limited purposes so far, should expand its applicable areas and reduce dependence on fossil resources, leading to diversification of energy sources. The overall thermal efficiency of the high-temperature gas furnace is expected to increase to at least 60%, because its high-temperature gases of around 1,000 degrees C can be used for heating processes, and the waste heat can be further used for generation of steam for power production. (NEDO)

Hydrogen energy technology development conference. From production of hydrogen to application of utilization technologies and metal hydrides, and examples; Suiso energy gijutsu kaihatsu kaigi. Suiso no seizo kara riyo gijutsu kinzoku suisokabutsu no oyo to jirei

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-02-14

The hydrogen energy technology development conference was held on February 14 to 17, 1984 in Tokyo. For hydrogen energy systems and production of hydrogen from water, 6 papers were presented for, e.g., the future of hydrogen energy, current state and future of hydrogen production processes, and current state of thermochemical hydrogen technology development. For hydrogen production, 6 papers were presented for, e.g., production of hydrogen from steel mill gas, coal and methanol. For metal hydrides and their applications, 6 papers were presented for, e.g., current state of development of hydrogen-occluding alloy materials, analysis of heat transfer in metal hydride layers modified with an organic compound and its simulation, and development of a large-size hydrogen storage system for industrial purposes. For hydrogen utilization technologies, 8 papers were presented for, e.g., combustion technologies, engines incorporating metal hydrides, safety of metal hydrides, hydrogen embrittlement of system materials, development trends of phosphate type fuel cells, and alkali and other low-temperature type fuel cells. (NEDO)

FY 2000 report on the results of the leading research and development of the carburetion technology using sensible heat of coke oven gas; 2000 nendo seika hokokusho. Kokusuro gas kennetsu riyo zonetsu gijutsu sendo kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of recovering sensible heat of coke oven gas (COG), the paper conducted a potential study of 'the carburetion technology using COG sensible heat,' of which the basic design is to give the endothermic catalyst reforming hydrogen production reaction directly to the components mainly including methane, and the R and D for establishing it as an industrial technology. In the R and D, the optimum process was studied in terms mainly of the dry pretreatment technology and the catalyst reformation reaction of hydrocarbons such as methane. As a result, the inhibition of the progress of the reforming reaction, which was a difficult problem at first because of the catalyst poison of associated components, could be avoided by making conditions for development/reaction of solid solution appropriate. Further, as to the associated coal tar which was regarded as carbon deposition source, a possibility of the process for converting it into the light chemical energy was recognized. Further, in FY 2000, survey was made on the solid electrolyte oxygen separation technology to which attention was paid as a chemical energy conversion technology for heat energy and which is closely related also to the energy structure of iron making plant. (NEDO)

FY1998 report on a survey related to joint utilization of welfare device development data using an international network; 1998 nendo kokusai network ni yoru fukushi kiki kaihatsu data no kyodo riyo ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A survey was made in relation with joint utilization of welfare device development data using an international network. Developing welfare devices requires data from ergonomic and medical systems, while the cope of the objects is wide, and the kinds are various. For proliferation of welfare devices, system compatibility evaluation including that on using environment is important, including living environments that are different by countries. The present survey has identified how data for aged, handicapped and help-needing persons are accumulated and utilized in research organizations in America and Europe for both of the ergonomic and medical areas. The survey also investigated major academic societies in overseas countries, and collected database and academic network information that support the advanced research and development. At the same time, investigations were also made on organizations and corporations who are moving forward the efficient data utilization. Welfare device and service information providing systems in Japan were investigated to compare them with the trends in other countries. Conceptions and methods were compiled to utilize data internationally and jointly. Database models for device development were considered, and a proposal was made on structuring a research and development supporting database, and the operation method thereof. (NEDO)

Utilization of coal fired power plant by-products. Utilization of coal ash; Sekitan karyoku ni okeru fukusanbutsu no yuko riyo gijutsu. Sekitanbai no yuko riyo

Energy Technology Data Exchange (ETDEWEB)

Kishimoto, K. [The Federation of Electric Power Companies, Tokyo (Japan); Watanabe, M. [Electric Power Development Co. Ltd., Tokyo (Japan)

1997-11-05

The paper introduced the present situation and future task of the tackling with effective use of coal ash discharged from coal thermal power plants. Making the use of the characteristics, coal ash is mostly used in the fields of cement/concrete, civil engineering/construction, and agriculture/forestry/fisheries. In the case of using fly ash to concrete, the effects are the heightening of long-term strength, increase in workability, decrease in hydration heat, control of alkali aggregate reaction, etc. In the civil engineering/construction field, coal ash is allowed to be used for road bed material and mixed civil engineering material as road materials, for revetment back-filling material, soft ground surface layer treatment, soft ground/soil improvement materials, FGC deep layer mixing treatment process, SPC (sand compaction pile) material, etc. as earth work materials. Besides, it is used for light coarse aggregate, light sand, etc., as construction materials, for material substituting ceramics products, etc. as building materials, and for agricultural material, potassium silicate fertilizer and ocean structure in the agriculture/forestry/fisheries field. 4 refs., 2 tabs.

Fiscal 1996 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the deep geothermal resource collecting technology (development of the deep geothermal resource producing technology); 1996 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen seisan gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper reported the results of the fiscal 1996 R and D of the deep geothermal resource collecting/producing technology. In the design of the total development, characteristics of the well mouth of the deep reservoir were examined to evaluate properties of deep geothermal resource, and the necessity of the pressure design, etc. were clarified. As to PTSD logging technology, conducted were improvement of PT probe, manufacture of a sonde of which S probe was integrated with memory/battery modules, and the actual well experiment. Concerning PTC monitoring technology, an experiment was carried out on a high temperature use optical fiber GI type, and it was shown that the type was on a commercial level. Further, a prototype sampler with 300degC heat resistance was trially manufactured, and a test to confirm its work was conducted in the well in the Corn Wall area of the U.K. As to the production control technology, studied was the arrangement of the production control technology for deep geothermal resource. Moreover, an experiment was made to examine the effect of metal ions coexisting when silica in the deep fluid precipitates. 46 refs., 107 figs., 38 tabs.

Fiscal 1996 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the deep geothermal resource collecting technology (development of the deep geothermal resource drilling technology); 1996 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper reported the results of the fiscal 1996 R and D on the development of deep geothermal resource collecting/drilling technology. In the design of a total development, the planned adjustment of actual well tests was conducted on bits and drilling mud at the time of drilling the exploration well of the Kakkonda area. As to the trend of overseas technology, examined was the developmental trend of high temperature type downhole motor products. In the development of hard high temperature strata drilling element technology, a drilling test was carried out on trially manufactured 300degC heat resistant/durable bits. In the development of high temperature drilling mud, drilling was done in the mud of thermally stable quality in the actual well experiment using the 300degC mud system. In the development of high temperature use cement and high temperature use cement slurry, a possibility was obtained of composing a slurry which has the targeted dewatering amount, compressive strength, and water permeability. In the development of high temperature downhole motor, data on characteristics of heat resistant stator materials were arranged in a relationship among the abrasion amount, thermal expansion amount and elastic recovery amount, and the database was obtained. 166 figs., 148 tabs.

FY 1997 - FY 2000 reports on the results of the development of commercialization technology of the photovoltaic power system. Summary. R and D of the photovoltaic power generation utilization system/periphery technology (R and D of high reliability storage batteries); 1997-2000 nendo New sunshine keikaku seika hokokusho (Sokatsu ban). - Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (Koshinraisei chikuden sochi no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The R and D/evaluation were made from FY 1997 to FY 2000 of lead storage batteries that are applicable to the use for the absorption of abrupt power variations in photovoltaic power generation and peak shift/emergency use power source, and the results were summed up. In the study for prolonging the life, the following were carried out: development of the inexpensive corrosion-resistant lead alloy positive grid applicable to the photovoltaic power generation, development of the negative active material with a high sulfation control effect, selection of silica powder as electrolyte retainer, development of the charging control technology by the multi-stage constant current method, etc. As a result, energy density of the battery was more than 70W/L as a target, and the target life of 3,000 cycles was achieved in the life test. Further, cost reduction and deterioration judgment were studied. In the study of the group of batteries, a management system for group of batteries was developed. As a result of the 1-year field test, there were no problems on durability of the storage case, temperature difference among batteries, rise in temperature, etc. As to the developed seal type lead storage battery, the applicability to the photovoltaic power generation was acquired. (NEDO)

Advanced research and development of gas hydrate resources. R and D of exploration and others - R and D of excavation technologies and others - surveys/researches on methods of evaluating environmental effects - surveys/researches on application systems; Gas hydrate shigenka gijutsu sendo kenkyu kaihatsu. Tansa nado ni kansuru kenkyu kaihatsu / kussaku gijutsu nado ni kansuru kenkyu kaihatsu / kankyo eikyo hyokaho no chosa kenkyu / riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Gas hydrate is a clathrate compound in a gaseous molecule as the host, stable under relatively mild environments. It is deposited in the 600m or deeper sea bottoms to form the gas hydrate deposit and massively occurring in the sea areas around Japan. This deposit has been studied viewed from natural gas resources, causes for natural hazards and contribution to the global warming. This project excavates a well in the deposit, to study possibilities of the technologies for decomposing, fluidizing and lifting the hydrate as the gas source, and for establishing the natural gas transporting/mooring systems in which its characteristics are utilized. The R and D activities are directed to the 4 areas, (1) development of the exploration technologies to determine the deposit sea area, quantity and conditions, (2) development of the stable well-excavation technologies, (3) studies on the effects of gas production on the environments, and development of the system for predicting the effects, (4) and studies on the application systems. The item (3) finds out the transportation/storage system possibly more economical than the current freezing/liquefaction technologies. The item (3) has the development themes of evaluating the geohazards caused by excavation and gas production, and their effects on the ecological systems. (NEDO)

Fiscal 1995 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the binary cycle power plant (development of the measurement while drilling system for geothermal wells); 1995 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (binary cycle hatsuden plant no kaihatsu (chinetsusei kussakuji kotei joho kenchi system no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The R and D were conducted of a detection system for measurement of data on the bottom hole of geothermal well, data transmission and signal processing, and an analysis system for well drilling trajectory control and well assessment while drilling of geothermal wells based on the data obtained by the detection system, and the results were reported of the technical development in fiscal 1995. In the development of the downhole detection unit, the following developments were conducted: mud pulse generator, bottomhole signal processor, mode switches, inclination information sensor, power source, measures against vibration/shock, sonde external equipment, tests to confirm heat resistance of electronic parts, and design/manufacture of testing devices. In the development of the surface detection unit, the development was made of experimental analysis program, interface program, and simulation. In the development of the analysis system, as a well trajectory control support system, made were a trajectory planning/display system and a trajectory prediction system. As a downhole assessment support system, made were a temperature analysis system and a pressure analysis system. 4 refs., 298 figs., 88 tabs.

Fiscal 1995 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the deep geothermal resource collecting technology (development of the deep geothermal resource drilling technology); 1995 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (shinbu chinetsu shigen saishu gijutsu no kaihatsu / shinbu chinetsu shigen kussaku gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper reported the results of the fiscal 1995 R and D on the development of deep geothermal resource collecting/drilling technology. In the design of a total development, the trend of technical development was examined of bits, cement and DHM overseas. Further, the simulational prediction was conducted in deep geothermal drilling. As to the development of element technology of hard high temperature strata drilling, the R and D of seal mechanism, bearing mechanism and cutter mechanism were carried out aiming at developing heat resistant/durable bits, and a bit was trially manufactured which was integrated with element parts selected by each element technology. Concerning the development of high temperature drilling mud, studies were made of the development of drilling mud materials, a mud system, etc. Relating to the development of high temperature cement slurry, the development was conducted of high temperature cement, dewatering adjusting agents, etc. As to the development of high accuracy much inclination drilling technology, in the development of high temperature use downhole motor, tests on heat resistance/durability were carried out in the mud of 12 kinds of high heat resistant stator materials. 175 figs., 137 tabs.

Fiscal 2000 achievement report on project for research and development of technologies for intelligent infrastructure creation and utilization. 'Development of high-efficiency protein expression system - 1 Development of system capable of high-efficiency expression of hyperthermophile-derived protein'; 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu gyomu seika hokokusho. Kokoritsu tanpakushitsu hatsugen system no kaihatsu -1 (Cho konetsukin yurai tanpakushitsu wo kokoritsu ni hatsugen suru system no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted aiming at the establishment of a system to enable the high-efficiency expression of the gene products of P. horikoshii OT3 and A. pernix K1. In an effort to develop a high-efficiency protein expression system with Escherichia coli acting as the host, studies were made about the expression of hyperthermophile protein by arginine rare codon elimination, and Ph FEN (flap endonuclease) was successfully overexpressed. In the development of Bacillus strains, screening was conducted for novel hosts, and a library was constructed for a screening task suitable for hyperthermophile-derived protein production. A system was also constructed capable of the high-throughput expression of various kinds of genes using Bacillus brevis. In the study of the expression of hyperthermophile-derived genes using T. thermophilus, promoter replacement resulted in an approximately 2-fold increase in representation at the maximum. Moreover, studies were made about the length at which foreign genes were efficiently incorporated into the T. thermophilus genome. (NEDO)

Fiscal 1996 report on the results of the subsidy operation under the Sunshine Project on the development of a geothermal water use power plant, etc. Development of the binary cycle power plant (development of the measurement while drilling system for geothermal wells); 1996 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Nessui riyo hatsuden plant nado kaihatsu (binary cycle hatsuden plant no kaihatsu (chinetsusei kussakuji kotei joho kenchi system no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The R and D were carried out of a detecting system for measurement of data on the bottom of geothermal well, data transmission and signal processing, and an analysis system for well drilling trajectory control and well assessment while geothermal well drilling based on the data obtained by the detecting system. The paper reported the results of the technology development in fiscal 1996. In the development of the detecting system, improvement/design were conducted on a mud pulse generator constituting sonde, well bottom signal processing equipment, mode switch and inclined information sensor, and the system equivalent to the actual one was manufactured to conduct a running test at high temperature/pressure. Moreover, a test to confirm heat resistance of electronic parts was made for further improvement in heat resistance of the sonde, in order to obtain the data. In the development of an analysis system, conducted were enhancement of operability of the planning/indication portions of the well drilling trajectory supporting system, improvement of the data intake system, etc. In relation to the well assessment supporting system, carried out were heightening of operability of the temperature analysis portion and confirmation of accuracy increase. 5 refs., 253 figs., 72 tabs.

Report on the achievements in fiscal 1999 of research and development of a femto-second technology. Research and developing of a electric power generation facility monitoring system utilizing high-luminance X-ray pulses; 1999 nendo femto byo technology no kenkyu kaihatsu seika hokokusho. Kokido X sen riyo hatsuden shisetsu monitoring system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Researches have been made with an objective to generate femto-second high-luminance X-ray pulses by using interactions between femto-second light pulses and high-density electron ray pulses, and to develop a technology to use the above pulses to measure objects moving at high speeds. This paper reports the achievements in fiscal 1999. In research and development of the ultra short light/electron ray pulse generating and controlling technology, totally solid laser was used as an excitation source for a mode synchronous laser transmitter. A high-accuracy moving stage driven by piezo elements and motor was used to actively control the resonator length by using the RF reference signals, wherein time fluctuation was reduced down to 100 fs level. Design and fabrication were performed on an electron ray accelerator and an electron ray transporter of the electron ray source system for Compton X-ray. Electron energy of 12 MeV and electric charge of 1 nC were achieved in an electron beam acceleration test. In the research and development of a femto-second high-luminance X-ray pulse generating technology, design and fabrication were carried out on a Compton collision chamber that can generate X-ray pulses with high luminance. (NEDO)

FY 2000 report on the results of development of the technologies for recovering and utilizing carbon dioxide using coal and natural gas; 2000 nendo sekitan tennen gas katsuyogata nisanka tanso kaishu riyo gijutsu no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

Described herein are the FY 2000 results of the research and development project for converting the gas, produced by reacting carbon dioxide and water with coal and natural gas using solar ray and heat, into methanol. A solar furnace operating with solar energy, composed of a simulated solar ray collector (5kW), CPC (Compound Parabolic Concentrator), molten salt furnace and coal gasifier, is designed, fabricated and installed. The motion in the molten salt furnace is simulated to analyze the heat flux. The wet and dry type coal gasification processes are simulated with Taiheiyo-coal as the basis. For the natural gas reforming solar furnace, various types of technical information on methane reforming and oxidation catalysts are pigeonholed. The catalytic reaction testing system is fabricated. The information of carbon dioxide separation technologies, e.g., membrane-aided separation, absorption, and membrane/absorption hybrid, is collected. The treatment test with the polyimide-based separation membrane is conducted. The information is pigeonholed and evaluated for development of the elementary techniques and optimization of the total system. The preliminary study on economic viability indicates that methanol production cost is 30 yen/kg-methanol or less, on the basis of releasing no carbon dioxide in the production step. (NEDO)

FY 1992 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1992 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1992 as the third year include on-the-spot surveys, tests for validating elementary techniques, designs and fabrication of part of the demonstration plant, and invitation of Philippine researchers to Japan. (NEDO)

FY 1991 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1991 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1991 as the second year include on-the-spot surveys, tests for validating elementary techniques, designs and fabrication of part of the demonstration plant, and invitation of Philippine researchers to Japan. (NEDO)

FY 1994 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1994 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

This 5-year joint project (FY 1990 to 1994) by Japan and the Philippines is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized in the Philippines into electric power, in which thermal decomposition/gasification of the wastes is combined with a gas engine system. The field tests of the demonstration plant successfully produce power of 100 kW by burning only the low-calorie gas with a heating value near critical level for self-sustained combustion, obtained by gasification of sawdust by the fluidized gasifier and refined, attaining the object of the project. It is confirmed that a 200 to 300 kW class commercial plant can be designed and constructed basically by scaling up the 100 kW demonstration plant. The other data obtained by the field tests include those for improved operability and maintainability, gas purification, and reducing sizes of the facilities, including utility facilities. (NEDO)

FY 1990 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1990 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1990 as the initial year include negotiations with the Philippines, on-the-spot surveys for the demonstration plant sites and conditions, and conceptual designs of the demonstration plant. (NEDO)

FY 1999 report on the results of the R and D of the plant use energy utilization rationalization industrial material production technology; 1999 nendo shokubutsu riyo energy shiyo gorika kogyo genryo seisan gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of using plants to the process to produce energy conservation type/environmentally friendly type industrial materials, the R and D were conducted on the improvement in material productivity/stress resistance of plants by transgenetic technology, etc., and the FY 1999 results were summarized. In the study of the creation of plants to produce industrial materials by genetic recombination of eucalyptus trees, it was found out that early maturing branches of eucalyptus trees were a material suitable for Agrobacterium infection, and conditions to efficiently acquire transformation calluses were obtained. In the R and D of the creation of soybeans to produce polyunsaturated fatty acid, a gene of unsaturated enzyme was acquired from Mortierella alpina storing ultra-long chain polyunsaturated fatty acid, and an experimental study was made to study whether or not this gene functions by plant. Further, studies were conducted on the technology to produce hybrid fiber by salt tolerance plants, creation of plants to produce isoprenoid/natural rubber, technology to produce tissue-specific high proteins, study on the molecular breeding of disease resistant plants, etc. (NEDO)

Research and development of system to utilize photovoltaic energy. Study on the scenario for the diffusion of photovoltaic power generating systems; Taiyoko hatsuden riyo sytem no kenkyu kaihatsu. Taiyoko hatsuden donyu fukyu scenario sakusei no tame no chosa

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the result obtained during fiscal 1994 on a survey to prepare scenario for the diffusion of photovoltaic power generating systems. Introduction target planned with help of a diffusion simulation was verified by calculations using simulation models. The calculations made the following points clear: facility costs and power generation costs for photovoltaic power generation systems, amount of introduced photovoltaic power generation systems, number of facilities introducing photovoltaic power generation systems, policy cost to achieve the target, annual power generation amount, oil substituting effect, carbon dioxide reducing effect, and market sizes. Power generation cost in fiscal 2000 would drop down to 53 yen per kWh in new installation in independent houses and down to 31 yen per kWh in systems used in schools. These reductions are the result of progress in mass production as a result of positively implementing the aiding policies. The required diffusion aiding policies revealed from the simulation results include expansion of subsidy operations for house construction, introduction of the systems into public facilities performed by public organizations, aid to system introduction into private business entities, subsidy to facility investments, and enforcement of power purchase institutions. 3 figs.

Joint Research. Report on the results of developing commercialization of a technology of process wastes and re-utilize them by using petroleum substituting energy; Kyodo kenkyu. Sekiyu daitai energy riyo haikibutsu shori saishigenka gijutsu jitsuyoka kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A study was conducted on a technology to melt shredder dust and non-combustible wastes directly by using coal, reduce their volume and re-utilize them. The elementary study on a high-temperature melting and treating technology set such targets as optimizing the melting and treating technology in correspondence with properties of materials to be treated, by using a small melting test plant, achieving a volume reduction rate of 1/200, and reducing treatment cost. In order to make innoxious the different kinds of environmental loading materials contained in exhaust gas from a high-temperature gasification and direct melting system, discussions were given on an optimum control condition for the exhaust gas system facilities. Furthermore, physical properties of discharges (slags nd metals) were investigated to discuss material re-utilization. In discussing optimal systems, three kinds of systems including two types utilizing fuels were proposed as high-temperature gasification and melting treatment process from a viewpoint of technology and cost. Respective systems were compared with each other on treatment cost, and their priorities were identified. 56 refs., 50 figs., 55 tabs.

FY 1998 annual report on the development of plasma-aided surface treatment processes by in-situ controlling (second year); 1997 nendo in-situ seigyo ni yoru plasma riyo hyohi shori process no kaihatsu seika hokokusho (dai 2 nendo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This R and D project is aimed at stable production of high-quality, important machine members, which are difficult to sufficiently achieve the required properties by a single material, by carburization while minimizing use of expensive alloy metals, where high-temperature carburizing time is reduced by a plasma-aided system to save energy, and, at the same time, the conventional oil-hardening system is replaced by a He gas cooling/recycling system to solve the environmental problems involved in the former. The exhaust gases released from the plasma-aided system are adequately treated to prevent the problems caused thereby. The conditions of the plasma itself and treated surfaces are sensed in-situ, and the data are fed back to the process controlling system, to keep the treated object stable and high in quality, while minimizing energy consumption. The FY 1998 efforts were directed to studies on methods for sensing the plasma and treated surfaces, and specifications of a mini-plant for the demonstration tests, and to collection of characteristic data for development of some new products to be produced. (NEDO)

Fiscal 1997 survey report. Subtask 5 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of hydrogen transportation/storage technology. 2. development of the liquid hydrogen transportation tanker); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 5 suiso yuso chozo gijutsu no kaihatsu dai 2 hen ekitai suiso yuso tanker no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Technology development is being conducted for construction of the long distance transportation tanker of large quantity liquid hydrogen. In fiscal 1997, test pieces of thermal insulating materials to be planned for fiscal 1998 were designed and studied. The purpose of the test is to confirm thermal insulating performance and behaviors of each material under the temperature of liquid hydrogen. The inside of the outer tank of the experimental equipment was held at vacuum of 10{sup -6} to 10{sup -7} Torr to exclude thermal convection effects and evaluate only heat coming from heater through the test piece. The heat from the heater at the lower part of the test piece is through the test piece and makes the liquid hydrogen of the upper tank evaporate. Thermal conductivity of the test piece is calculated from the evaporation quantity. As to PUF (polyurethane foam) panels, studied were reformation preventive measures, influential evaluation of the side transfer heat quantity, and the time required for vacuuming. In the vacuum panel, study subjects were extracted on the selection of core materials, reformation preventive measures, deterioration with age, the practical manufacturing method of experimental panels, etc. As to the super insulation, subjects were studied on the performance measuring method/accuracy, measures against heat transfer from the inside of the experimental equipment, control of the vacuum degree, etc. 10 refs., 45 figs., 6 tabs.

Fiscal 1980 Sunshine Project research report. Development of hydrothermal power plant. Development of binary cycle power plant (Research on heat cycle, heat medium, material and heat medium turbine); 1980 nendo nessui riyo hatsuden plant no kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu (netsu cycle oyobi netsubaitai no kenkyu, zairyo no kenkyu narabini netsubaitai turbine no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the fiscal 1980 research result on each element of the next 10MW class geothermal binary cycle power plant, following last year. In the research on heat cycle and heat medium, measurement was made on the liquid density, vapor density, liquid specific heat, vapor specific heat and thermal conductivity of 8 heat media to prepare the precise pressure enthalpy chart. The thermal stability of each medium was also measured under a flow condition. The heat cycle of each medium was calculated in a hydrothermal temperature range of 120-160 degrees C for evaluation of its output. In the research on material, field corrosion test and laboratory simulation were made on 3 kinds of heat exchanger martials for acidic hot water to study the corrosion behavior of welding members. In the research on heat medium turbine, study was made on sealing characteristics such as differential pressure, flow rate and friction of sealing oil for oil film seal and mechanical seal as shaft seal devices of heat medium turbines for the 10MW class geothermal plant. (NEDO)

Fiscal 2000 achievement report. Research and development of semiconductor CVD chamber cleaning systems for electronic device manufacturing using new alternative gas instead of SF6, PFCs, and other gases; 2000 nendo sokkoteki kakushinteki energy kankyo gijutsu kaihatsu seika hokokusho. SF6 tou ni daitaisuru gasu wo riyo shita denshi debaisu seizo cleaning system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The efforts aim to develop a CVD (chemical vapor deposition) mechanism cleaning gas with less environmental impact such as global warming and a CVD process using the same. The candidate gas synthesizing study for the development of such a gas continues from the preceding fiscal year. In addition, various candidate gases and tentatively synthesized gases are evaluated for their cleaning performance using a simplified experimental system. As the result, patent applications were filed for three novel alternative gases low in environmental impact and high in cleaning performance. In the research and development of CVD processes, a verification test process is developed for the evaluation of alternative gases at the real system level using a large CVD evaluation system. Studies are also made in which some existing gases are utilized to improve on CVD cleaning efficiency and to reduce greenhouse gas emissions. In relation to the process, one domestic patent application is made, and three essays are presented at an international conference on electrochemistry in the United States. (NEDO)

Fiscal 1981 Sunshine Project research report. Development of hydrothermal power plant. Development of binary cycle power plant (Research on heat cycle and heat medium, materials, and heat medium turbine); 1981 nendo nessui riyo hatsuden plant no kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu (netsu cycle oyobi netsubaitai no kenkyu, zairyo no kenkyu narasbini netsubaitai turbine no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This report summarizes the final fiscal 1981 research result on components of the next 10MW class geothermal binary cycle power plant. In the research on heat cycle and heat medium, R-C318 and R-124 were excellent in output characteristics in a low-temperature zone and high-temperature zone in a hot water temperature range of 120-160 degreesC, respectively, however, at present R-114 was most reasonable from the viewpoint of heat medium price and supply system. In the research on martials, study was made on inlet-attack and stress corrosion of heat exchanger pipes of 18Cr-13Ni-2Mo steel, and combination use of inexpensive materials (carbon steel). As used giving attention to stress corrosion, at present 18Cr-13Ni-2Mo steel was most suitable material, while clad carbon steel was also usable. In the research on heat medium turbine, the 1000-hour durability test result of mechanical seal showed that mechanical seal is best for heat medium turbines. (NEDO)

Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 9. Development of liquid hydrogen transportation and storage technologies - 1; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 9. Ekitai suiso yuso chozo gijutsu no kaihatsu - 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the achievements in fiscal 2000 from the development of liquid hydrogen transportation and storage technologies. Discussions were given on the following three types of specimens as the heat insulation performance test structures: the vacuum panel type (polyurethane foam coated with SUS sheet, while the inside is kept in the vacuum state); the solid vacuum type (combination of polyurethane foam with vacuum heat insulation); and the powder under normal pressure type (a structure in which the ambient of powder pearlite heat insulating material becomes the atmospheric pressure, whereas a SUS case is set up to separate vacuum layer of the test apparatus from atmosphere layer of the specimen, with the SUS case filled with pearlite). Adding the two types of specimens used in the previous fiscal year, five test specimens in total were discussed on the result of the performance tests to advance the database management. As a low temperature strength test for the insulating materials, the compression test was performed on a microsphere being a kind of solid vacuum (normal pressure) heat insulating materials at room temperature, the liquid nitrogen temperature and in liquid hydrogen atmosphere. The compression strength under liquid hydrogen is 1,044 MPa, which is two times greater than the normal temperature strength of 496 MPa, representing the compression strength rising in proportion with temperature drop. Problems were extracted in developing a small capacity liquid hydrogen transportation and storage system. (NEDO)

Report on research and development achievements in fiscal 1979 in Sunshine Project for geothermal water utilizing power plants. Separate volume of surveys and studies on plant development plans (Surveys on trends in overseas technologies); 1979 nendo chinetsu nessui riyo hatsuden plant no kenkyu kaihatsu seika hokokusho (plant kaihatsu keikaku chosa kenkyu). Bessatsu (Kaigai gijutsu doko chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

This paper describes surveys on trends in overseas technologies in development plans for geothermal water utilizing power plants. In heat cycles, the binary and two-stage flash cycles were analyzed by using a generalized equation of state, and theses on optimizing working fluid properties and cycle conditions with maximum thermal efficiency were described. Theses that were described include those for criteria to select working fluids and thermal power cycles against the binary cycle using a heat source at 104 to 204 degree C. The binary cycle working fluid was found better in mixed systems than in pure systems as seen from process and economic performance. The paper introduces a heat conductivity experimenting device and data required for designing a heat exchanger. It also describes the Heber geothermal experimental plant to demonstrate reasonability of assumed working media. A fluidized bed type and a shell tube type were applied to heat exchangers at the Raft River 50 MW geothermal power plant for comparison and discussion. Fouling factor was also estimated. A discussion was given on fluidity distribution of a fluidized bed heat exchanger. Design of a heat discharge system is important for geothermal power generation because heat source temperatures are so low that more than 85% of heat that has been taken in is discharged. The paper also describes turbines and other facilities. (NEDO)

Fiscal 2000 achievement report on research and development of intelligent infrastructure creation and utilization technologies. Research and development of fluid and high-temperature melt thermophysical property standard data and measuring technology; 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu jigyo seika hokokusho. Ryutai oyobi koonyutai no netsu bussei hyojun data to keisoku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Thermophysical data relating to industrially important materials and substances were determined and collected for databasing. In the buildup of standard data for natural circulation substances and their water solution thermophysical characteristics, pure ammonia and aqueous ammonia, containing 51.95 mol% and 83.74 mol% of ammonia, were measured, and the excessive molar volume, isothermal compression rate, and the coefficient of volume expansion were acquired. In the buildup of standard data for polymeric thermophysical properties, blends of poly(PPO) and polystyrene were taken up, and the dependence of CO2 solubility on the composition was studied. In the buildup of standard data involving fluids mainly refrigerants, heat of evaporation, specific heat capacity of liquid refrigerant, and speed of sound in rarefied refrigerant gas were measured, and various apparatuses for measuring PVT (pressure, volume, temperature) were developed. In the buildup of standard data relating to the vapor-liquid equilibrium property of fluids, a tertiary system comprising water, alcohol, and a polymer of ethylene glycol at 298.15K was studied, and measured by use of a constant pressure flow type vapor-liquid equilibrium measuring apparatus. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Study of peripheral device for AC module); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (AC module yo shuhen sochi no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For widening the application of photovoltaic power generation, the AC (alternating current) module technology was examined for validity, and effective ways to utilize the technology and tasks to solve for its further development were studied. In fiscal 1999, concerning the validity of the AC module technology, it was shown quantitatively that attention should be paid to the inhibition of radio interference although the AC module was the more advantageous when under the influence of shadow. In the study of various measures for utilizing the technology, it was shown that, although the technology contained many tasks to discharge, such as need for downsizing and cost reduction, improvement on environmental resistance, and the prevention of radio interference, yet it had many advantages expected to turn up in the future, such as reduced influence of shadow, high flexibility in system design, and decreased installation cost. In the study of technical tasks to discharge in the course of development, it was stated that AC module integrated inverters (MICs) were already on the market, that an autonomous distributed type system control method suited the purpose of AC module systems, and that it was important to develop a thin MIC technology for application in the next generation. (NEDO)

Report on achievements in fiscal 1999 on the project for research and development of an intellectual base creating and utilizing technology. Development of a screening test method with high accuracy for internal secretion disturbing substances; 1999 nendo chiteki kiban sosei riyo gijutsu kenkyu kaihatsu. Naibunpi kakuran busshitsu no koseido screening shiken hoho no kaihatsu oyobi data kiban seibi

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes the achievements in fiscal 1999 on developing a screening test method with high accuracy for internal secretion disturbing substances. Development was made in cooperation with the OECD on the screening method that uses as a parameter whether a chemical substance has a hormone-like activity. For the womb breeding assay method to evaluate a feminine hormone-like activity, a reproducibility and comparison test was performed on womb breeding in immature rats administered with ethinylestradiol, the administration routes, and animals used (young and weak rats, and rats whose ovaries have been extracted). In order to evaluate a masculine hormone-like activity, the basic data were collected to develop the Hershberger method, and participation was made in the OECD verification tests. Discussions were given on comparison on castrated and non-castrated rats when 17 {alpha}-methyltestosterone was administered, the administration period of time and reproducibility when immature rats were used. The Hershberger method reactivity was discussed on rats relative to estrogen. In a toxicity test using 28-day repetitive administration, bisphenol A gave impacts on the kidney, the stomach and intestine tubes. (NEDO)

Report in fiscal 1999 on the achievements in research and development of the ITS technology using clean energy driven automobiles. Research and development of an efficient utilization system for car rentals in tourist resort areas; 1998 nendo clean energy jidosha wo mochiita ITS gijutsu no kenkyu kaihatsu seika hokokusho. Kankochiyo rentaka koritsuteki riyo system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes the achievements in fiscal 1998 on developing ITS technology using clean energy driven automobiles. Development is intended on an efficient management and control method for EV car rentals in tourist resort areas using the ITS technology from the viewpoints of reducing road traffic load and global environment problems. The development items include a control center system, a system to control battery charging status at the center, a battery charging determination algorithm, and a car navigation and bi-directional communications mounting system. The system development has been completed nearly completely, having attained relatively high user satisfaction. However, because of the experimental rented cars having long mileage, there were few chances of verifying the charge determination algorithm and the functions of the ITS. Investigations were carried out on technological trends in overseas countries on EV and ITS, and on commuter car introduction projects. Structuring the hardware for a commuter EV system is not too difficult if the presently available EV and ITS technologies are used. However, in advancing commercialization, there are such assignments as establishment of software, operation patterns, and interfaces that enhance user convenience and profitability. (NEDO)

Development in fiscal 1999 of technology commercializing photovoltaic power generation system. Research and development of power generation application system and peripheral technologies (Survey and research on evaluation of photovoltaic power generation); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden hyoka no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective of evaluating the contribution to the global environment of utilization of photovoltaic power generation, discussions were given on evaluation of photovoltaic system life cycle, evaluation of contribution to environment, and total evaluation. This paper summarizes the achievements in fiscal 1999. In evaluating the PV system life cycle, the roof-integrated modules using the thin film CdTe cells were selected as the evaluation object to estimate the energy payback time (EPT) and the CO2 emission unit consumption rate. In case of annual production of 10 MW, the EPT is 1.8 years and the CO2 emission unit consumption rate is 13 (g-C/kWh), which were found largely reducible by expanding the annual production size. For the environmental contribution evaluation which focuses on CO2 emission suppression effect as the discussion object, discussions are being given on the introduction scenario needed for the analysis. In the total evaluation, the direct employment effect assumed in Japan was discussed on production, distribution sales, installation, maintenance control and dismantling of photovoltaic generation system for residential use. The discussion showed the effect of about 7 persons per year per MW in production size of 100 MW. (NEDO)

Fiscal 1997 survey report. Subtask 5 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of hydrogen transportation/storage technology. 3. development of liquid hydrogen storage equipment); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 5 suiso yuso chozo gijutsu no kaihatsu dai 3 hen ekitai suiso chozo setsubi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the WE-NET development of large capacity liquid hydrogen storage technology, a study has been continued with a target of 50000 m{sup 3} storage development. As to the result of conceptual design and various types of the thermal insulating structure, to confirm the performance, studies were made on the thermal insulating performance test and the strength test on thermal insulating materials to be started in fiscal 1998. The large-capacity common testing equipment for thermal insulation performance to be used in and after fiscal 1998 was fabricated, and the basic performance of the equipment was confirmed by the preliminary cooling test. Further, the test pieces simulated of various thermal insulating structures were designed to study the thermal insulation performance, reformation during the test, strength, etc. It is required to solve problems such as weight reduction of test pieces, prevention of reformation, retention of vacuum, etc. In the test on strength of thermal insulating materials, a test is conducted to confirm strength of thermal insulating materials at temperatures of hydrogen by the extremely low temperature strength test equipment. The studies on test pieces to be used were summed up including the items to be paid attention to during the test because the test situation is different from that in testing metal materials. Since hydrogen is a very flammable gas, much attention should be paid to safety during the test. 13 refs., 63 figs., 32 tabs.

Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 6. Development of the polymer electrolyte membrane fuel cell supplied with pure hydrogen; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu seika hokokusho. Task 6. Junsuiso kyokyu kotai kobunshigata nenryo denchi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research result on development of element technologies for a pure hydrogen fuel cell power system of nearly 45% in efficiency at terminal, and demonstration test result on the 30kW class polymer electrolyte membrane fuel cell system supplied with pure hydrogen. On cell voltage characteristics in high-utilization operation, study was made on degradation and corrosion caused by short supply of hydrogen by using a single cell. As a result, it was found out that reverse polarization of -3.0V has small effect, however, that of -0.7V causes corrosion and deterioration of cell characteristics in a short time. In operation using actual-size cells for the 30kW class plant, it was effective to wet cells on the air side. On hydrogen high-utilization operation technique, study was made on hydrogen recovery and recycle operation, anode outlet line closed operation, and anode recycle operation. In addition, some studies were made on specifications of auxiliary facilities for fuel cells, safety measures for fuel cells and humidity control of supplied hydrogen gas. (NEDO)

Fiscal 2000 achievement report on project for research and development of intelligent infrastructure creation and utilization technologies. Research and development project on high-speed deformation characteristics evaluation methods for metallic materials; 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu jigyo. Kinzoku zairyo no kosoku henkei tokusei hyoka hoho no kenkyu kaihatsu jigyo - Gyomu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts were made to develop methods for evaluating the characteristics of metallic materials experiencing high-speed deformation or impact deformation. The research was conducted by the research WG (working group) consisting of some participants of an international conference convened this fiscal year. The research result revealed that studies in Japan lopsidedly dealt with metallic materials at strain velocity of 10{sup 4}/second or less, such as steel, while many studies overseas dealt with materials other than metals at strain velocity over 10{sup 4}/second. The test and evaluation WG conducted high-speed tension tests for T6-treated aluminum alloys using the split Hopkinson bar method, hydraulic servo method, one bar method, and the sensing-plate method for measuring force, and the results were compared. It was then found that the one bar method produced disturbance more remarkably than the others and that the loading block structure and load rise time influenced the emergence of the peak load. The emergence of a peak load in the Hopkinson bar method or the one bar method had been predicted on the basis of the research conducted by the analysis group. (NEDO)

Fiscal 1997 survey report. Subtask 5 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of hydrogen transportation/storage technology. 4. Development of various kinds of common equipment); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 5 suiso yuso chozo gijutsu no kaihatsu dai 4 hen kakushu kyotsu kikirui no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the WE-NET development of a large-capacity liquid hydrogen pump, a magnetic bearing was studied. The test piece is a 1/3 scale model of the actual equipment, in which two radial bearings and one thrust were combined, and the impeller and turbine blade were distributed in both ends. Ti was used to the rotor and turbine, permalloy to the electromagnet, and aluminum to the case. The flotation control is made by 5-axial control, and each control coefficient was so selected that rigid body primary and secondary modes can enter into the safe domain in control. Further, as the position sensor used for control, the one used to the liquid hydrogen turbo pump of the rocket engine was made opposite and was used with the temperature characteristic compensated. The test was conducted under the extremely low temperature environment of liquid nitrogen/hydrogen temperature. It was confirmed that the sensor and electromagnet work favorably. The rotation experiment was carried out under the extremely low temperature environment and enabled the rotation up to approximately 19000 rpm. The dangerous speed of the axial rigid body is in around 6000 to 10000 rpm, and it was possible to pass this. Further improvement will be made by the tuning of control. 70 figs., 8 tabs.

Report on the achievements in fiscal 1998. Hydrogen utilizing international clean energy system technology (WE-NET). Subtask 8. Development of hydrogen combustion turbine (development of major components such as turbine blades and rotors); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 8. Suiso nensho turbine no kaihatsu (turbine yoku, rotor nado shuyo kosei kiki no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The present research and development is intended to establish the fundamental technologies required to develop a pilot plant, by investigating development of such major component devices as turbine blades and rotors in a hydrogen combustion turbine. In the turbine moving and stator blade cooling technology, it is intended to achieve the power plant efficiency of 60% (based on HHV) as established in the interim evaluation performed in fiscal 1996. Therefore, the necessary element tests, detailed blade design, and partial fabrication were moved forward on the three kinds of the selected blade cooling systems as the cooling systems that can deal with the steam temperature condition as high as 1,700 degrees C. Fiscal 1998 will execute the design and fabrication of test blades and testing devices for blade cooling evaluation tests to be performed at Tashiro Township in Akita Prefecture. At the same time, evaluation and selection will be made on the three kinds of the cooling blades. In the rotor cooling technology, for the purpose of analyzing the rolling-in phenomenon of steam in the main turbine flow, a method will be developed to analyze rotor disk cavity temperatures based on CFD, the basic sealing conditions based thereon will be discussed, and generalization will be made on the rotor cooling technology. (NEDO)

FY 1999 Technical research and development for environmentally friendly and highly efficient energy utilization system. Technical research and development for highly efficient and effective energy utilization (Technical research and development for optimum system designs - Part 2); 1999 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 2. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Research and development program is conducted for the elementary techniques as part of the eco-energy urban project of New Sunshine Project. Described herein are the FY 1999 results for the (techniques for transportation and storage of energy). The R and D on methanol energy systems involves the R and D on decomposition and synthesis catalyst of methanol and methyl formate for the waste heat sources of relatively low temperature. The R and D on high-efficiency techniques using hydrogen-occluding alloys involves development of heat exchangers of low sensible heat ratio, fabrication of double-effect type MH heat pump cycle devices, and demonstration tests for the system operation. It is found that the heat output of the hydrogen-occluding alloy for high temperature use is 0.18kW/kg at 90 degrees C, and that the alloy can be massively produced. A thermal utilization efficiency COP of 0.68 is obtained for the double-effect type MH heat pump cycles. The R and D on the heat-hydrogen recovery, transportation and utilization techniques involves designs and fabrication on a trial basis of a sensible heat recovery unit. (NEDO)

FY 2000 report on the results of the development of the environmentally friendly type high efficiency energy utilization system. Part 2. Study of the effective utilization technology of high efficiency energy (Study of the optimum system design technology); 2000 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 2. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

The paper conducted the development of the environmentally friendly type high efficiency energy utilization system and the R and D of the high efficiency energy effective utilization technology, and the FY 2000 results were summed up. As to the energy transportation/storage technology, the R and D were made on the following: methanol/energy system, non-equilibrium high efficiency methanol decomposition reaction technology, development of multiple functions of catalyst, high efficiency heat pump technology using hydrogen storage alloys, heat-hydrogen recovery/transportation/utilization technology, vacuum insulated heat transport piping system, surfactant used for high density heat transport, high density latent heat transportation technology, etc. Concerning the energy supply/utilization technology, the R and D were made of the heat supply system using high efficient heat pump corresponding to multiple fuels. Relating to the environmental load reduction technology, the energy conserved heat pump system using natural coolant. As to the optimum system design technology, the comprehensive preparation of element technology, etc. (NEDO)

FY 1999 Technical research and development for environmentally friendly and highly efficient energy utilization system. Technical research and development for highly efficient and effective energy utilization (Technical research and development for optimum system designs - Part 1); 1999 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 1 Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Research and development program is conducted for the elementary techniques as part of the eco-energy urban project of New Sunshine Project. Described herein are the FY 1999 results for the 'techniques for recovery and conversion of unutilized energy'. The R and D on waste heat recovery and conversion for chemical plants designs an internal structure of the 'wetted wall column for shell side as the stripping section' for increasing quantity of heat exchanged inside, and stably operates the bench plant for 100 hours or more. The R and D on thermoelectric power generating systems using low calorie exhaust gases involves development of materials, production of fine particle materials and sinters, and evaluation of their functions, among others. The program for application of the techniques to commercial plants confirms applicability of a 3kg thermoelectric power generating system to automobile coating process. The R and D on systems for thermoelectric recovery of low-temperature waste heat finds cracks on the ceramic plate for the power generating system WATT100, disassembled for repair. (NEDO)

FY 1999 Technical research and development for environmentally friendly and highly efficient energy utilization system. Technical research and development for highly efficient and effective energy utilization (Technical research and development for optimum system designs - Part 3); 1999 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 3. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Research and development program is conducted for the elementary techniques as part of the eco-energy urban project of New Sunshine Project. Described herein are the FY 1999 results for the (techniques for transportation and storage of energy (continued), energy supply and utilization, reducing environmental loads, and designing the optimum systems). The R and D on heat transfer system through the vacuum heat insulation pipes involves fabrication, on a trial basis, the vacuum insulation covers for the vacuum insulation tubes, joints, flanges and valves for the 80A pipes, and the heat loss evaluation test for each item. The R and D on the energy supply and utilization techniques involves the heat transfer systems for a variety of fuels by the highly functional heat pump, and compression/absorption hybrid type heat-utilization system. The hybrid type heat-utilization system simulation results suggest possibility of achieving exergy efficiency of 56% as the development target by use of the new medium. The R and D on the environmental load reduction involves the power-saving type heat pump systems which use a natural coolant. (NEDO)

FY 2000 report on the results of the research and development project for utilization of information of high-molecular-weight structures in a living body. Survey on the technological trends of utilizing the reactions with metals in a living body; 2000 nendo seitai kobunshi kozo joho riyo gijutsu kaihatsu chosa hokokusho. 'Seitai kinzoku hanno riyo gijutsu' ni kansuru gijutsu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the survey on the technological trends of utilizing the reactions with metals in a living body, noting the bio-processes effectively coping with the environmental problems. The effects of heavy metals on microorganisms have been investigated on the molecular biology level, but are not fully elucidated. Recently, the microorganisms capable of converting inorganic metal ions in water into the insoluble compounds have been known, leading to possibility of bioremediation to solve pollution by heavy metals, which have detrimental effects on human health. Heavy metals must be recovered, because they are not extinct by decomposition. The plant aided purification has been attracting attention to cope with heavy metals accumulated in soil. Application of bacteria-aided leaching, which is adopted as one ore smelting process, to the technologies for utilizing metals in a living body has been expected, because diversified activities of inanimate matters in extreme environments have been known. Recently, bio-machining of metals aided by Thiobacillus ferrooxidans, one species of independent nutrient bacteria capable of eating metals, has been developed to a potentially viable stage. (NEDO)

FY 2000 report on the results of the development of the environmentally friendly type high efficiency energy utilization system. Part 1. Study of the effective utilization technology of high efficiency energy (Study of the optimum system design technology); 2000 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 1. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

The paper conducted the development of element technology and comprehensive adjustment which are related to the development of the environmentally friendly type high efficiency energy utilization system and the study of the high efficiency energy utilization technology, and the results of FY 2000, the final fiscal year, were summed up. As to the R and D of the exhaust heat reforming/recovery system, the internal heat exchange type distillation tower was developed which has a good energy conservation effect and enables the heat supply outside. Concerning the R and D of the cogeneration system using low calorie exhaust gas, the following were conducted for further improvement of the performance of electrothermic elements: evaluation of the thermoelectric performance using bulk elements, development of new elements and evaluation of the energy balance at the time of combustion, etc. Relating to the R and D of the low temperature exhaust heat utilization cogeneration system, conducted were the development of thermoelectric materials and the fabrication/evaluation study of module. Moreover, WATT20A equipped with the original power generation module developed in this study was fabricated, and the data on the operation at the temperature of 150 degrees C were obtained by WATT-20HT. (NEDO)

FY 2000 report on the results of the research and development project for utilization of information of high-molecular-weight structures in a living body. Survey on the technological trends of utilizing the reactions with metals in a living body; 2000 nendo seitai kobunshi kozo joho riyo gijutsu kaihatsu chosa hokokusho. 'Seitai kinzoku hanno riyo gijutsu' ni kansuru gijutsu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the survey on the technological trends of utilizing the reactions with metals in a living body, noting the bio-processes effectively coping with the environmental problems. The effects of heavy metals on microorganisms have been investigated on the molecular biology level, but are not fully elucidated. Recently, the microorganisms capable of converting inorganic metal ions in water into the insoluble compounds have been known, leading to possibility of bioremediation to solve pollution by heavy metals, which have detrimental effects on human health. Heavy metals must be recovered, because they are not extinct by decomposition. The plant aided purification has been attracting attention to cope with heavy metals accumulated in soil. Application of bacteria-aided leaching, which is adopted as one ore smelting process, to the technologies for utilizing metals in a living body has been expected, because diversified activities of inanimate matters in extreme environments have been known. Recently, bio-machining of metals aided by Thiobacillus ferrooxidans, one species of independent nutrient bacteria capable of eating metals, has been developed to a potentially viable stage. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development of novel type solar cell module integratable with building materials - Highly durable roof module); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu - kotaikyusei yane module)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A thin-film solar array, a large roof panel, and an interconnecting power conditioner are integrated into one and single structural member for the development of a residential photovoltaic power system in which a unit AC (alternating current) output is collected from each panel. In fiscal 1999, in the study of highly durable materials for solar cell modules and of their structure, a thin film compound solar cell module was enlarged to 82cm times 71cm, evaluated for performance, and installed on the third test house. In the study of collecting AC power from the solar cell module, a compact power conditioner for a roof panel which had been in test operation on the roof of the laboratory since 1998 was checked for practical performance, improved, and evaluated for system generation efficiency. In the study of a highly durable roof module structure, problems pertaining to heat radiation from the rear side steel sheet, the burning of the junction box, etc., were solved, and the module passed a verification test under the Building Standard Law. In the validation of the roof module for which power generation performance and meteorological conditions had already been continuously measured for 19 months, it was found that the roof module suffered no troubles such as water leak or deformation. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of building material integrated solar cell modules - high-durability roof modules); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (kotaikyusei yane module))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With the target set on a system with a roof array efficiency of 8.5%, and a system cost of 170 yen/W, development is being made on a large roof panel and its construction technology, which is capable of AC output by integrating into a large roof panel the compound thin film solar cells having glass/CdS/CdTe/rear air chamber/rear metal, and the inverter. In the cell constituting materials and the structure design, sealants were evaluated, the painting process was developed, and two kinds of structures were prepared. The frameless type has a lamination structure, and a prototype module of 886 times 664 mm was fabricated, and the frame type has a double sealing structure, and a prototype module 600 times 900 mm was fabricated. Prototype modules that can be fixed on a rail type fixing stand were fabricated and constructed, having demonstrated sufficient workability. In addition, a prototype small inverter with system coordination protection was operated actually, and the initial stage malfunctions were corrected. Two demonstration buildings were built, and the whole process was performed from assembly and transportation of the modules and to the installation thereof at the construction site. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development of novel type solar cell module integratable with building materials - Novel multilayer structure module); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu - shinfukuso kozo module)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The project aims to develop solar cell modules of a novel multilayer structure, based on the resin filling structure, hollow structure, and the laminate structure, and integratable with building materials. In fiscal 1999, for the development of cells and submodule structures, cells and submodules were fabricated which were usable with various specimens. In the case of design oriented cells, electrode structures and linkage methods were improved for the enhancement of power generation performance, and a hollow structure and a laminate structure were fabricated. As for the 4m{sup 2}-large module (laminate structure), a specimen with dummy cells arranged along its periphery was fabricated. For cost reduction, a study was made about a module (laminate structure) integrated with an ALC (autoclaved lightweight concrete) board, and the kind of surface glass, cell arrangement, and back sheet types and their respective designs were evaluated. It was then concluded that the module was fit for practical application. The module was then checked for wind endurance in a wind endurance test, for electric characteristics, and for flame inhibition capability in a fire prevention/resistance test. (NEDO)

FY 1998 report on the results of the development for an advanced application system for glass waste with CO2 emission reduction; 1998 nendo CO{sub 2} haishutsu yokuseigata hai glass kodo riyo system no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the realization of the cycling recycle society, it is important to promote recycling using glass waste for CO2 reduction and effective use of resources. The paper described the FY 1998 results of the development. It included the classification by which the composition of the particle sizes required for recycled products will be made possible, basic studies for low-cost pulverization/separation of foreign substances, and tests on heightening of process accuracy. Relating to the artificial synthesis of feldspar/pottery stone using glass waste/alumina waste as starting materials, vitrification behavior was studied to find out the optimum synthesis conditions. Glass waste of 60% and aluminum hydroxide of 40% were mixed at calcination temperature of 1,100 degrees C for more than 1 hour. Properties of the artificial feldspar/pottery stone were similar to those of the natural one. As to the utilization of glass waste to hydrothermally solidified materials, high-strength solidified matter without crack was obtained in the three-component system of G powder/hydrated lime/gypsum. Concerning the production of eco-glass block, a study was made on the size and mixing ratio of the cullet waste which is very soluble and has no effects on performance. The paper touched also on the R and D of the environmentally friendly type system using multi-functional hybrid materials. (NEDO)

Achievement report for fiscal 2000 on research and development of high level waste glass utilization system of CO2 emission suppression type; 2000 nendo CO2 haishutsu yokuseigata hai glass kodo riyo system no kenkyu kaihatsu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to establish a waste glass recycling system of low cost and requiring less CO2 emission amount and energy consumption, research and development has been made on classification of waste glasses into particle composition that is required in regenerated commercial products. This paper summarizes the achievements in fiscal 2000. In the research of a waste glass reusing and supplying system designed by using LCA, discussions were given on items required in circulating and recycling waste glass resources, and quality control on raw materials and products. Evaluations of product quality control items were made on crystallized glass, sintered glasswool, automotive window glass, electric bulbs, fluorescent lamp glass, and quartz glass. Utilization tests were carried out for Mashiko porcelain china clay with an intention of expanding the application of waste glass, whereas the relationship between waste glass addition amount and optimal sintering temperature range was verified, disclosing that the limit of the waste glass addition is 10%. In the research on multi-functional hybrid materials, discussions were given on light-weight tiles and water permeating blocks with regard to the manufacturing technology, facility specifications, product quality, effects of the functions, and durability. (NEDO)

Generic supercritical water technology; Generic technology to shite no chorinkaisui riyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

Arai, K; Ajiri, M; Inomata, H; Smith, R; Hakuta, Y [Tohoku University, Sendai (Japan). Faculty of Engineering; Yokoyama, C [Tohoku University, Sendai (Japan). The Institute forChemical Reaction Science; Chin, L [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

1997-02-01

This paper describes the measurement and analysis for clarifying solution structure of supercritical water and exhibition mechanism of solvent functions. It also describes the development of new processes using supercritical water as reaction solvent. The PVT measurements were conducted in the supercritical region using pure water and NaCl aqueous solution, to confirm the reduction of molar volume of the electrolyte solution. The hydration structure was examined in the supercritical aqueous solution by the molecular dynamic simulation. As a result, presence of hydrogen bond structure, where the contribution of two branching hydrogen bond can not be ignored, was suggested under the supercritical condition. Characteristics of supercritical aqueous solutions are analyzed through in-situ Raman and scattered X-ray spectral measurements. Moreover, this paper introduces developments of some processes in the supercritical water, such as decomposition of wasted polymers, recovery of chemical materials, reforming of heavy hydrocarbons by contact hydrogenation, and synthesis of fine powders of metal oxide by reaction crystallization.

Feasibility study of international cooperation in the research/development of a solar energy utilization system by the innovative solar thermochemical process; Kakushinteki solar netsukagaku process ni yoru taiyo energy riyo system no kaihatsu kenkyu ni kakawaru kokusai kyoryoku kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

At COP3 in 1997, an agreement was made to the innovative technical development/promotion by international cooperation, and the promotion of transfer of environmental technology to developing countries. Under the agreement, a feasibility study of international cooperation was made, and especially a study was conducted of the utilization/development of solar energy by the innovative solar thermochemical process. The main reason for global warming is emissions of a large amount of CO2 caused by the direct combustion of fossil fuels. Therefore, a CO2 recycle system taken up in the study enables a more substantial decline in CO2 emission (kg/kWh) per unit generation than the conventional thermal power system by composing solar methanol or solar dimethyl ether using fossil fuels including coal, water, CO2, etc. as raw materials and using solar energy as heat source, and by using this as fuel (solar fuel). CO2 can be reduced by 13% to 14% by substituting solar methanol or solar dimethyl ether produced from petroleum/methane equivalent-mol mixed raw materials for the equivalent mol coal and natural gas of the thermal power plant (CO2 recovery is not necessary). 34 refs., 47 figs., 34 tabs.

International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 1. Research study on integrated evaluation and development plan; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 1. Sogo hyoka to kaihatsu keikaku no tame no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper describes the research result on the WE-NET project in fiscal 1996. The WE-NET project is composed of various elemental technologies such as hydrogen production, transport, storage, low-temperature material, utilization and hydrogen combustion turbine. The organic integrated cooperation and coordination between individual subtasks are indispensable for effective promotion of the project and optimization of the total system. The current R and D states of every elemental technology were surveyed, and its findings were utilized for coordination of the whole project and examination of the research project including pilot studies. Eleven important items in the total coordination including a total system cost and safety measures in a developmental stage were examined. The development results for 4 years of fiscal 1993-1996 were assessed together, and the draft working plan for fiscal 1997-1998 was also decided. The verification test plan of a hydrogen combustion turbine scheduled in Phase II was studied, and the basic plans of development step were proposed. The draft report of a transition scenario was also prepared. 6 figs., 68 tabs.

Development of hydroponic system using agriculture waste. 1. Characteristics of rice husk charcoal as growth medium and vegetable growth; Suiko saibai ni okeru haikibutsu riyo gijutsu no kaihatsu. 1. Momigara kutan no baichi to shite no tokucho to yasai no seiiku

Energy Technology Data Exchange (ETDEWEB)

Terazoe, H; Nakaya, K; Okano, T [Central Research Institute of Electric Power Industry, Tokyo (Japan)

1994-06-01

Experimental researches were made on rice husk charcoals processed to be used as culture media for hydroponics. Rice husk charcoals with a size of 1 mm or larger retaining the original shape of the rice husk, and with a size of smaller than 1 mm were made for use in the experiment. In the culture media made of these rice husk charcoals, the charcoal with a particle size greater than 1 mm had more air portion than water portion at 6 cm above the water level, and the charcoal with a particle size smaller than 1 mm had poor air permeability. According to the result of immersing the rice husk charcoal in a culture solution, phosphoric acid ion and manganese in the solution decreased by about 35% and calcium by about 10% in the duration of 120 minutes, as a result of having been adsorbed into the rice husk charcoal. On the other hand, chloride ion increased by about 80% and potassium and iron by about 30%, because of having been dissolved out from the charcoal. In cultivating spinach, butterhead lettuce and radish in the rice husk charcoal culture media, the culture medium with charcoal smaller than 1 mm resulted in harvest reduced by about 75% in spinach, and about 10% in butterhead lettuce. 15 refs., 13 figs., 11 tabs.

Fiscal 1997 survey report. Subtask 4 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of hydrogen production technology); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 4 suiso seizo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As a WE-NET subtask, a study has been conducted of the solid polyelectrolyte water electrolysis method by which higher efficiency and lower cost hydrogen production is expected than in the conventional hydrogen production method. Production methods of electrode, electrolyte, etc. were studied. In the electroless plating method, the manufacturing process of membrane-electrode assemblies was realized in a large area of 2500 cm{sup 2} by the porous-surfaced method by studying manufacturing conditions for slurry membrane/membrane assembly/electroless plating processes. In the hot-press method, the refining degree and dispersibility of iridium dioxide powder were studied to improve characteristics of anode catalyst. A method was developed to form polyelectrolyte coatings homogeneously on the surface of electrode layer catalytic powder, and a large area of 2500 cm{sup 2} was realized. Beside the performance test using large single cells, FS was conducted to discuss optimum operating conditions and optimum structures of plants. Both methods indicated the performance exceeding the energy conversion efficiency of 90%, a WE-NET target, at current density of 1A/cm{sup 2} and electrolysis temperature of 80degC. A key was found to a bench-scale development (electrode area of 2500 cm{sup 2}, about 5 layers) to be planned in fiscal 1998. 136 figs., 50 tabs.

FY 1999 report on the results of the R and D of the CO2 emission control advanced system for glass waste (public use); 1999 nendo seika hokokusho (Kokaiyo). CO2 haishutsu yokuseigata hai garasu kodo riyo system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D were conducted of a low cost and low CO2 emission/consumption energy supply system which can classify glass waste into the grain size distribution required for recycled products and supply it as raw material, and the FY 1999 results were summed up. As to the R and D of the glass waste recycling supply system technology with LCA-design, study was made on the quality management of raw materials and products. Concerning the grain size of products, examined were effects of changes in revolution number of grinder on the particle size of product and production amount. In the developmental study of the application, conducted were the analysis of grain shape, preparation sintering and heavy metal elution test of crystal fine and crystal powder. In the study of artificial synthesis of the pottery stone material, almost the same product as the conventional one was obtained by dispersing/mixing G powder and aluminum hydroxide and calcinating them at 1,100 degrees C. Trial products such as teacup and ash tray were manufactured. Besides, the R and D were carried out of the use of glass waste for hydrothermally solidified materials, eco-glass block, lightweight tile/permeable block, etc. (NEDO)

Report on the achievements in fiscal 1999. Technology to use gas hydrate as a resource (Research and development for exploration, research and development on drilling technologies, investigative research on an environment influence evaluation method, and investigative research on a utilization system); 1999 nendo gas hydrate shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansa nado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The contents of the research and development performed in the current fiscal year are as follows: (1) research and development for exploration, (2) research and development on drilling technologies, (3) investigative research on an environment influence evaluation method, and (4) investigative research on a utilization system. In Item (1), element analysis data are used to study a method to estimate production environment of hydrate ore beds by using an inorganic ion analyzer and a trace amount element analyzer, the crust thermal flow measuring method is used to discuss a method to analyze the hydrate stability zones together with the data of sea area exploration records, and conceptual design is made on a resource potential evaluation system. In Item (2), experiments and analytical discussions are performed on decomposition control of the gas hydrate solid-liquid interface according to such conditions for the drilling fluid as temperatures and flow rates. Elucidation is given on the initial process of bubble generation for behavior of decomposed gas bubbles. Observation and elucidation are made on two-phase flow behavior of non-Newtonian fluid. In Item (3), conceptual design is carried out on a system to detect elements of shape change in each bed due to fluid movement in a gas hydrate bed and an upper bed. In Item (4), discussions are given on the optimizing conditions for generation and dissociation of gas hydrates. Investigation is made also on a possibility of the transportation and storage system. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of building material integrated solar cell modules - modules with new multi-layer structure); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (shinfukuso kozo module))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Development is being made on a panel type module that can be used together with an air bubble concrete board (ALC board), and is provided with design characteristics. The development work includes trial fabrication and evaluation of a module with new multi-layer structure, and development of a technology to unitize cells and submodules, and a systematizing method. In the trial fabrication and evaluation, flame retardant and uninflammable modules using fluororesin, and modules with as large area as 4 m{sup 2} were fabricated on a trial basis, in addition to the modules with the basic structure. These modules were given evaluations on such wall material properties as wind pressure resistance, heat and cracking resistance, and fire resistance. In a deformation resistance test considering the integrated use with the ALC board, the developed modules showed a good result. In developing the cells with design characteristics, discussions were given on the inter-cell wiring methods. Development was made on a method to establish a unit structure based on the design and size of a building. In developing the systematization method, the trial fabrication method was applied to a module with lamination structure, a module integrated with the ALC board, and a large-area hollow module to have fabricated the top-light spandrels. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development for enhancing reliability of photovoltaic power generation - Research on long-term reliability of inverter); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden no shinraisei kojo ni kansuru kenkyu kaihatsu - inverter no choki shinraisei no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In fiscal 1999, the power conditioner which is the primary component of a photovoltaic power system was subjected to an accelerated test, etc., for the evaluation of its durability. For the accelerated test, operating conditions were so set that acceleration be implemented according to Arrhenius' law at ambient temperature 40 degrees C and relative humidity 36%. For the operation of the power conditioner, it was so set that the operation duration be 3.5 hours with a rest time of 4.5 hours for the night or the like. In the accelerated test conducted as in the previous year, 1100 cycles were completed recording the maximum, equivalent to approximately 8-1/2 years according to Arrhenius' law. After the test, no life affecting changes were detected in specimen device A, B, or D. Specimen C, however, failed during the test. As for the evaluation of durability of components, the electrolytic capacitor in the power conditioner was named. Reliability related literature was investigated and a durability evaluation test was started, with consideration given to the voltage to apply and service temperature. (NEDO)

Achievement report for fiscal 1993. International clean energy system technology to utilize hydrogen - WE-NET (Sub-task 5. Development of hydrogen transportation and storage technology - Edition 4. Development of different common devices); 1993 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) (Sub tusk 5: Suiso yuso chozo gijutsu no kaihatsu - Dai 4 hen. Kakushu kyotsu kikirui no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

In developing hydrogen transportation and storage technologies based on the WE-NET project under the theme of the 'development of different common devices', surveys and discussions have been performed on four themes with high urgency. It was revealed that, with respect to the large liquid hydrogen pump, the survey report should be reported on the pump models, motors, reduction of NPSH, and bearings, and that the cryogenic pump technology has a necessity of further development because the technology is biased to pumps for rocket with high head. With regard to the vacuum heat-insulated piping with large diameters, such strict problems in the technological development were made clear as high heat insulating performance, optimization of the shield structure, measures for thermal stress, anti-seismic measures, and sealing mechanism at joints, in addition to the vacuum heat insulating piping technology that has been built to date. The liquid hydrogen valve is subjected to a technological problem of the very low temperature and combustion performances of liquid hydrogen, which requires further researches. With respect to the instrumentation facilities, as a result of discussing the liquid level meter system and the flow rate meter system, it was found that there is no almighty method, whereas selection of the method should be as required in particular situation. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research on meteorological data for design optimization); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (saiteki sekkei no tame no kisho data no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For collecting solar radiation data necessary for the prediction of power to be outputted by photovoltaic power systems in Japan, detailed experiments and observations were conducted with an emphasis placed on the amount of solar radiation on a slope facing north and on the amount of solar radiation broken down by wavelength. Models were analyzed, and the fiscal 1999 results were compiled. In the validation of a model of solar radiation on an inclined surface, a review was conducted using the 1-year data observed at the Takasaki station for all directions, including solar radiation on the slope facing north, and the validity of the model was confirmed. As for the validation of a model for estimating solar radiation by duration of sunshine, it was examined for accuracy using the same data, and was found to be fairly high in accuracy. For the maintenance of solar radiation data for each wavelength, continuous observation was conducted for each wavelength of solar radiation at the Takasaki station using a multi-filter spectroradiometer, and a technique was established to determine spectral distribution using the observed data. Moreover, continuous observation of global diffused solar radiance was conducted using a sky scanner at the said station and solar cell power generation characteristics was continuously monitored. (NEDO)

FY 2000 report on the results of development of technology for commercializing high-efficiency fuel cell systems. Development of technology for commercializing high-efficiency fuel cell systems (Development of technology for effective utilization of power produced by polymer electrolyte fuel cell systems); 2000 nendo kokoritsu nenryo denchi system jitsuyoka gijutsu kaihatsu seika hokokusho. Kotai kobunshigata nenryo denchi no shutsuryoku yuko riyo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This project is aimed at development of technologies for effective utilization of power produced by polymer electrolyte fuel cell (PEFC) systems and waste heat, to spread cogeneration systems incorporating PEFC systems for residential purposes. Described herein are the FY 2000 results. The program for high-efficiency peripherals for residential PFEC systems attempts use of GaN-FET as the semiconductor device of wide band gap and high breakdown voltage to realize conversion efficiency over 90% by improving inverter efficiency. Two types of the prototype heat recovery systems are developed for the PEFC, one incorporating a latent heat cooling system and the other a water cooling system, to improve heat recovery efficiency and increase heat recovery temperature. The program for technology to fit PEFC output to energy demand develops hot water supply systems provided with a hot water storage function for stable supply of hot water irrespective of the heat recovery conditions, and also with a back-up function with burners. The program also develops the PEFC system of fine load following characteristics, for which pure hydrogen is used as the fuel to allow the system to instantaneously follow fluctuating loads. The program for high-efficiency partial load operation technology studies a 1kW-class residential PEFC cogeneration system incorporating a power storage device for high-efficiency operation at partial loads, where the former operates in a high output mode while the latter absorbs fluctuating loads. (NEDO)

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field / Development of the plasma use surface treatment process by in-situ control (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / in-situ seigyo ni yoru plasma riyo hyohi shori process no kaihatsu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described the fiscal 1997 result of the development. To know of in-plasma phenomena such as carburization and nitriding, a basic plasma experimental device was fabricated for quantitative measurement of reaction activity species. For the study of reaction control between plasma and substrate, a rotary analyzer type ellipsometer was fabricated as a method to detect composition and thickness of the deposit on the substrate surface. For He gas cooling after carburization and hardening, basic specifications for He gas refining/circulating system were confirmed. For perfect non-hazardous processing of exhaust gas from plasma carburization furnace, conducted was the thermodynamic computation of the process. Priority in order of the functions to be possessed as specifications for basic design of mini plant is plasma carburization, He gas cooling, and in-situ measurement. To make the most of the plasma use surface treatment as substitutes for expensive alloy elements, sliding parts/die-cast mold raw materials were carburized to measure the hardness. The Cr carbide coating technology by plasma CVD is also under study as an application example except carburization. 47 refs., 59 figs., 31 tabs.

Hydrogen utilization international clean energy system technology (WE-NET). Subtask 5. Development of technology of hydrogen transportation/storage (3rd edition, development of liquid hydrogen storage equipment, report on results of Air Liquide); Suiso riyo kokusai clean energy system gijutsu (WE-NET). Subtask 5. Suiso yuso chozo gijutsu no kaihatsu (daisanpen ekitai suiso chozo setsubi no kaihatsu Air Liquide sha seika hokoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

In the fiscal 1995 study, items were searched which are keys to the design of a liquid hydrogen tanker of a capacity of 200,000m{sup 3}. Among those, the basic concepts were summarized which are necessary for the design of a liquid hydrogen tanker in terms of safety, and the extraporation of the existing low temperature technology into the large liquid hydrogen tank was studied. When adopting safety conditions of IGC Code applied to LNG to the liquid hydrogen tanker, it is necessary to limit the discharge amount of hydrogen to 3 kg/s. When considering safety at fire, for keeping safety of the same level as that of the LNG tanker, it is not appropriate to adopt the conventional vacuum insulation liquid hydrogen tank. In the fiscal 1995 study, 7 kinds of concept of the insulation structure were assumed, and it was concluded that BOR of 0.04-0.23/d was obtained. Also in fiscal 1996, the large liquid hydrogen tank was studied. For insulation of the large liquid hydrogen tank, the structure is most promising where AEROSIL bag or homogeneous AEROSIL is substituted for a forming heat insulating material of 4 design, but further study is needed for selection of the optimum heat insulating structure. 9 figs., 6 tabs.

Achievement report for fiscal 1993. International clean energy system technology to utilize hydrogen - WE-NET (Sub-task 8. Development of hydrogen burning turbines - Development of main components including turbine blades and rotors); 1993 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) (Sub tusk 8: Suiso nensho tabin no kaihatsu - tabin yoku rota tou shuyou kosei kiki no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Among the research and development items in relation with the 'development of hydrogen burning turbines' based on the WE-NET project, surveys have been performed on developing the main components including turbine blades and rotors. The current fiscal year has surveyed the latest trends in the existing gas turbine and rotor cooling technologies, and the technological problems were extracted from the viewpoint of application to the hydrogen fueled turbines. Since the hydrogen fueled turbines have the entrance temperature higher than that of power generation gas turbines, development of the blade cooling technology is important. Main cooling methods available are the film cooling and transpiration cooling, whose technological development is necessary in the advanced forms. Cooling method for the inner side of blades includes the impingement cooling and the pin fin cooling, whereas the V-letter shaped turbulence accelerating rib and the serpentine flow path structure are considered promising. Increasing the anti-heat temperature of blades may be realized by utilizing ceramics. As a technology close to putting it into practical use, application of heat shield coating is promising. (NEDO)

FY 1993 report on the results of the subsidy project for the Sunshine Project. Development of coal use hydrogen production technology (Support study of pilot plant - Trial development of materials of plant use equipment); 1993 nendo Sunshine keikaku hojo jigyo seika hokokusho. Sekitan riyo suiso seizo gijutsu kaihatsu - Pilot plant no shien kenkyu (Plant yo kiki zairyo no shisaku kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

As to the development of coal use hydrogen production technology, the paper made the test study on the improvement of gasifier use materials and evaluation of the characteristics, the evaluation test in the environment using the actual machine, etc., and the FY 1993 results were reported. The results of the study were as follows. Concerning the shaped refractory for gasifier hearth, it was found that high chromia base and picrochromite base refractory development materials had much more excellent coal slag resistance than other existing component-system materials. It was shown that the development materials began to deteriorate under the coal gasification environment at temperatures of about 1,500 degrees C or higher. As to the mullite ceramics, a possibility was shown of improving the slag permeation resistance by making the crystal grain coarse by long-time sintering. By the survey of the state of damage of the proposed materials (refractory and iridium) used in the operational environment of the pilot plant, the outlook for use limit was made clear. In the environment test using the actual machine on the proposed metal base alloy of the typical equipment of the pilot plant, the correspondence between the operational environment and material corrosion was made clear. (NEDO)

Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 6. Development of fuel cell of pure hydrogen fueled solid polymer type; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 6. Junsuiso kyokyu kotai kobunshigata nenryo denchi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for research and development Task-6. The objective is to verify performance and reliability, by means of field tests, of a power generation plant using fuel cells of pure hydrogen fueled solid polymer type with power transmission terminal efficiency of 45% and output of 30 kW. The fuel cells were developed by using the cathode humidification process as a humidification method suitable for operation at high utilization rates. With a three-cell stack made by using this humidification process (having an effective area of 289 cm{sup 2}), verification was made on the current density of 0.2A/cm{sup 2}, the characteristics of 0.75V or higher, and the uniform voltage distribution performance being the immediate targets. In order to mitigate the hydrogen utilization in the fuel cells, discussions were given on the serial flow system that divides the laminated cells into two blocks. Thus, operation was found possible with the utilization rate in each block reduced to about 80% by selecting an adequate division rate even if the hydrogen utilization rate is 96% in the entire stack. Stable operation has been performed in the 5-kW class power generation test using the cathode interior humidifying system. Specifications for 30-kW class power plant, system configuration, safety, and material balance were discussed. The basic design was made on the hydrogen gas humidity adjusting system. (NEDO)

Effective utilization technology of carbon dioxide. CO sub 2 no yuko riyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

Ibusuki, T. (National Research Inst. for pollution and Resources, Tsukuba (Japan))

1991-03-12

As carbon dioxide-related environmental measures, method was explained to chemically convert and utilize carbon dioxide. Synthesis is possible of methanol, carbon monoxide, different carbohydrates, etc. by catalytic hydrogenation of carbon dioxide, using hydrogen produced by the electrolysis of water. Task consists of heightening in both convertibility and selectivity, and abundant supply of low cost hydrogen. Methane, alcohol, etc. can be synthesized by electrochemical reducion of carbon dioxide. Because of effectively inserting multiple electron, discssion is being made of catalyst, intergrated with electrode, and electron transmitter. The photoelectrochemical reduction of carbon dioxide can be also made by utilizing photoelectric current, generated upon photoradiation on the semiconductive electrode. However, task consists of heightening in both efficiency and selectivity. Photochemical reduction of carbon dioxide, actually made by green plant, consists of oxidationlike decomposition of water and reduction of carbon dioxide. Both those reactions are skillfully separated by intermediation of very quick electron transmission system. Reduction is being studied with semiconductor, metallic colloid, enzyme, metallic complex and other various catalysts. 10 refs., 3 figs., 4 tabs.

Guide for biogas energy utilization in Hokkaido; Hokkaido bio gas energy riyo guide

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of smoothly introducing biogas plants to Hokkaido in the future, the following were conducted: collection of the data on samples of development/introduction of biogas plants, survey of the organizations concerned, etc., study of economical efficiency, etc. Those were arranged as a guide for biogas energy utilization in Hokkaido. In the biogas plant, organic matters such as animal faces, garbage, etc. are anaerobicly fermented at medium temperatures between 35 and 38 degrees C or at about 55 degrees C to obtain biogas including methane gas of approximately 60%. From this gas, heat is obtained by gas boiler, and also electricity and heat are obtained by gas cogeneration or fuel cells. In the case of introducing the biogas plant using animal faces as raw material in Hokkaido, it is important to cover all the electricity and heat used to maintain the plant with the biogas obtained, from a viewpoint of economical efficiency. In the present situation, it is the most economical for each farmer to introduce an individual plant to be installed and to obtain the power generated and heat. (NEDO)

Developments of space station; Uchu station no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Hashimoto, H. [National Space Development Agency of Japan, Tokyo (Japan)

1996-03-05

This paper introduces the Japanese experiment module (JEM) in developing a space station. The JEM consists of systems of a pressurizing section, an exposure section, a pressurizing portion of a supply section, a manipulator and an exposure portion of the supply section. The pressurizing section circulates and controls air so that crews can perform experiments under pressurized environment. The exposure section is a part in which experiments are carried out under exposure environment. The supply section runs between a station and the ground, with required devices loaded on it. The manipulator performs attaching a payload for the exposure section and replaces experimental samples. The JEM undergoes a schedule of fabricating an engineering model, testing for a certification a prototype flight model, and putting the model on a flight. The pressurizing section, exposure section and manipulator are at the stage of system tests. Surveillance of the JEM and control of the experiments are carried out at the Tsukuba Space Center. The Center is composed of a space experiment building, a zero-gravity environment testing building, an astronaut training building, a space station operating building, and a space station testing building. 7 figs., 2 tabs.

Fiscal 1997 survey report. Subtask 6 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of technology of low temperature materials); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 6 teion zairyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described the results of the development of technology of low temperature materials in the fiscal 1997 WE-NET. Using experimental equipment for materials under the atmosphere of liquid hydrogen, an experiment on mechanical characteristics under the liquid hydrogen atmosphere (20K) was conducted of the base materials of candidate steels (SUS304L, SUS316L and A5083). In material evaluation experiments (tension/fracture toughness/fracture tests), characteristic behaviors of the materials were shown which are different from those shown in the environment of liquid He (4k), etc. Even if the amount of {delta} ferrite in the metal welded of the stainless steel is small, approximately 1%, the degradation of low temperature toughness occurred. Welded joints of stainless steel by submerged arc welding and MAG welding were in now way inferior in tension characteristic to those by TIG welding, but were inferior in toughness ranging from room temperature to extremely low temperature. As to aluminum alloys, materials excellent in extremely-low temperature toughness were able to be found. Under the low temperature hydrogen gas atmosphere, the lower the strain rate is, the higher the hydrogen brittleness susceptibility is around 220K (extremely large hydrogen brittleness temperature) (SUS304L). In the hydrogen gas of 100 atm, hydrogen invades the material at 100degC, but does not at 77k. 38 refs., 173 figs., 48 tabs.

Worldwide clean energy system technology using hydrogen (WE-NET). subtask 8. Research and development of hydrogen combustion turbines (evaluation of the optimum system); Suiso riyo kokusai energy system gijutsu (WE-NET). subtask 8. Suiso nensho turbine no kenkyu kaihatsu (saiteki system no hyoka)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Based on the proposed cycle of each contractor, conceptual design of 500 MW class hydrogen combustion turbine power generation plant has been completed through its economic examination. The optimum system has been evaluated on the basis of the conceptual design. For the conceptual design of power generation plant, the gross power generation efficiencies based on HHV of topping regenerating cycle and new Rankine cycle proved to be 61.8% and 61.7%, respectively, which exceed the target efficiency 60%. Economic consideration proved that the construction cost of each cycle will be as the same as that of the current combined cycle power generation plant. The development problem, development step and development cost have become clear. Examination on the reliability proved that the operation reliability of each cycle will be as the same as that of the current combined cycle power generation plant. Examination on the plant layout proved that the conservation of space for each system will be smaller than that of current combined cycle power generation plant. Environmental examination confirmed that each system is very clean power generation system. For the evaluation proposed by each company, the total points of each system became in the order, topping regeneration cycle, new Rankine cycle, and Rankine cycle with reheat and recuperation. 112 figs., 44 tabs.

Investigation on application of coal ash, lime and gypsum-based compositions. ; Development of technology to utilize and dispose of used desulfurizing agnet. Sekitanbaiter dot sekkaiter dot sekkokei soseibutsu no oyo ni kansuru chosa. ; Shiyozumi datsuryu zai no riyo shori gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Mori, K. (The Hokkaido Electric Power Co. Inc., Sapporo (Japan))

1991-11-20

This paper describes the result of an investigation by testing on re-utilizing the used desulfurizing agent discharged from a thermal power plant as a sludge disposer and a deodorant. The used desulfurizing agent used in the test is a nearly neutral substance composed mainly of SiO{sub 2} and CaSO{sub 4}. The paper describes that the tested agent has a character to solidify when added with water, and the solidified substance made from the agent added into a sludge is nearly neutral and usable in the similar manner as in the commercially available sludge solidifying materials. The paper also reports that in a field test for applying this tested agent to cover the sludge surface, a marked effect of improving water quality was recognized, including the increased water transparency. It also states that the tested agent absorbs ammonia actively, and that as a result of investigating its applicability as a deodorant for pet excreta odors, the agent can be handled more easily than the commercially available deodorants and has a deodorizing effect equivalent to or better than them. 4 refs., 7 figs., 6 tabs.

Overview of FY1997 human media technology R and D; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido Shin energy Sangyo Gijutsu sogo Kaihatsu Kiko itaku jigyo. Human media no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports a summary of results in fiscal 1997 of research and development of human media technology. Fiscal 1997 launched design and trial fabrication of the following items: interface to improve efficiency and safety of plant operators, accommodation of multimedia contents to aid Kansei design, city development design aiding technologies using contents retrieval and presentation technologies and virtual reality, and empirical evaluation technologies for safety, comfort and convenience. Specific study assignments were extracted on a virtual media technology, a Kansei media technology and a knowledge media technology being three elementary technologies for human media to make clear the research and development approaches to be taken in the coming fiscal years. In addition, a human media technology committee, a research and development working group, and an investigation working group were established. Also launched were investigations on research trends in the human media technology, and investigative researches on contacts of information needs in industries with human media. 59 refs., 114 figs., 24 tabs.

Research and development of utilization technology of solar thermal system for industrial and other use. Development of passive solar system (research and development of advanced glazing); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Passive solar system no kaihatsu (chokozai nado no kenkyu kaihatsu (advanced grazing no kenkyu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for advanced glazing in which solar energy is efficiently utilized. The peripheral techniques are surveyed for evaluation of characteristics of large-size dimming glass, optimization of film compositions and scaling up. The dimming device, made on a trial basis, attains a target controllable rage of at least 50% for visible light transmittance. The suitable components include WO3 as the electrochromic material producing color under a reducing atmosphere, NiO as the counter electrode producing color under an oxidative atmosphere, and hydrated SbOx as the proton-conducting electrolyte. The test results indicate possibility of the dimming glass stably operable while being irradiated with a quantity of sun ray of around 10 years. The study on scaling up the dimmer glass develops, on a trial basis, a process for producing large-size glass and evaluates its characteristics, where the film parameters are investigated. It also investigates the peripheral techniques for assembling the devices for the large-size glass, and develops useful techniques, such as those for sealants and improved sealing methods. 1 fig., 1 tab.

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Development of solar beam power generation and utilization systems and ancillary technologies (Research and development of new building material integrated solar cell modules - investigation and research on analysis of practical application); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (shinkenzai ittaigata taiyo denchi module no kenkyu kaihatsu (jitsuyoka kaiseki ni kansuru chosa kenkyu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to promote the research to put new building material integrated solar cell modules into practical use, the following items were investigated: (1) functions and specifications for harmonizing with buildings, (2) new module materials that can respond to building materials, (3) marketability, (4) standardization of the assessment methods, (5) consistency with relevant legislation and related institutions, (6) effects on environment as building materials, and (7) investigation on technological trends inside and outside the country. In Item (1), the significance of developing the new building material integrated solar cell modules was made clear. In Item (2), the performance requirements on the currently used module materials were put into order. In Item (3), the market size was investigated, and assignments to establishing the market were put into order, such as the distribution and construction institutions, and assistance to the system introduction. In Item (4), standardization and unification of the assessment methods were discussed, and the items to be standardized were extracted. In Item (6), LCA on the currently used modules was performed. In Item (7), participation was made to the second solar beam power generation conference and EUROSUN '98; investigations were made on trends of developing the new building material integrated solar cell modules and how the recycling related legislation is being progressed; and the achievements in the development activities were confirmed, and the assignments were investigated at the new building material integrated solar cell module subcommittee. (NEDO)

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. R and D of the photovoltaic power generation utilization system/periphery technology (R and D of the new solar cell module integrated with construction materials - Investigative study on analysis for commercialization); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Taiyoko hatsuden riyo system, shuhen gijutsu no kenkyu kaihatsu (Shinkenzai ittaigata taiyodenchi mojuru no kenkyu kaihatsu - Jitsuyoka kaiseki ni kansuru chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of supporting the study for commercialization of the new module integrated with construction materials, survey of the technical trend of the new module integrated with construction materials in Japan and abroad was conducted, and the FY 2000 results were summarized. As to the module material correspondent to construction materials, the results of the survey made in the past three years were summarized, and the subjects to be considered in future were arranged from a viewpoint of disposal/recycle of modules. Concerning the marketability, various policies for the spread of solar cell module that is an immature good were arranged. Survey was also made of the photovoltaic power system using the field test project as a sample, and the following were made clear: The photovoltaic power generation has appeal for environmental consideration and energy conservation; In some cases, the power generation effect was not as much as expected because the information on design/construction is not sufficient. Relating to the evaluation of its effect on the environment, the paper summarized the environmental influence in each of the module methods at each stage of production/utilization/disposal and the basic items for measures to cope with the influence. (NEDO)

Achievement report for fiscal 1997 on the research and development to lead to gas hydrate using technology. Research and development on exploration, research and development on drilling technologies, survey and research on a method to evaluate environmental impact, and survey and research on a utilization system; 1997 nendo gas haidoreto shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

The present study is intended to analyze comprehensively geophysical, geological and geochemical data, and establish a technology to estimate distribution of gas hydrate (GH) in sea areas around Japan. It is also intended to develop a high-accuracy resource amount calculating method utilizing the result of excavation of GH planned in the future. In order to achieve these goals, the following activities are performed: (1) study on a method to estimate production environment of GH deposits, (2) development of a method to estimate GH stability areas by using the crust thermal flow measuring method, and (3) study on estimation of GH distribution and wide-area potential. For the study (1), an inorganic element analyzer was introduced, and calibration of devices was performed in fiscal 1997. A survey was carried out on literatures related to distribution of inorganic elements and process of GH deposit production. In the study (2), design and trial fabrication were executed on a high-accuracy crust thermal flow measuring device, capable of long-term continuous observation. In the study (3), re-processing focusing on BSR was implemented by using the latest computer and analysis software on the data in which BSR has been confirmed in the surveys done in the past on sea areas around Japan. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Research and development of photovoltaic power utilizing system and peripheral technologies (Research and development for enhancing reliability of photovoltaic power generation - Research on environmental measures for compound solar cell modules); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden no shinraisei kojo ni kansuru kenkyu kaihatsu - kagobutsu taiyo denchi module no kankyo taisaku no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research is conducted to properly deal with environmental problems, such as compromised solar cell safety, which may follow the mass introduction and diffusion of photovoltaic power systems. In the research of fiscal 1999 on technical literature on environmental measures against lead and animal tests, a need was found to reduce lead in power systems and to grasp lead elution characteristics for the establishment of environmental measures. In a safety test conducted for thin-film CIS (copper indium diselenide) based solar cells, basic data were collected about the vaporization rate of Se, the effect of moisture on the Se vaporization rate, etc. Basic data were also collected about the relationship between the combustion temperature and the amount of scattered lead in particular from the solder used as the conducting material in silicon based solar cells. In the evaluation of the environmental impact of thin-film CIS solar cells in case of fire, it was found that Se concentration below 10-20m in the plume was near the permissible concentration of 0.1mg/m{sup 3} as recommended by Japan Society for Occupational Health and that the concentration levels predicted for the periphery were two orders of magnitude smaller than the mandatory level. (NEDO)

Fiscal 1996 report on the results of the study under a consignment from NEDO of environmental friendly type metal base-materials recycling utilization basic technology and element/overall process. For public; 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko kyodo kenkyu itaku. Kankyo chowagata kinzokukei sozai kaisei riyo kiban gijutsu no kenkyu: yoso sogo process kenkyu seika hokokusho (kokaiyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A study of `the next generation new iron steel making process` was conducted in which impurity elements in scrap are removed and recycled into high quality steel making materials, and at the same time total emissions are reduced during the process from scrap melting to steel making. The paper reported the fiscal 1996 results. In the study of the scrap recycling process, conducted were a study of the total system to remove impurities in the high temperature preheating furnace, a large scale experiment of de-coaling combined type de-coppering/de-tinning under reduced pressure of iron melting, a study of recycling technology of dust to the scrap melting furnace, etc. In the study on preheating/melting technology, a study of the scrap melting furnace of high-productivity/low-energy vertical type, a study of the scrap preheating method using the packed bed type preheating furnace, a study on the flue gas control at the time of preheating/melting, a study of the fast assessment method for organic compounds in flue gas, etc. In the evaluation of the total system, a study of preheating/melting/environmental systems using experimental plants. 20 refs., 23 figs., 10 tabs.

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Research and development of solar beam power generation and utilization systems and ancillary technologies (Investigations and researches on evaluations of photovoltaic power generation); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (taiyoko hatsuden hyoka no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Values given to global environment and economy by utilization of photovoltaic power generation are evaluated, and quantified to make clear the significance of the utilization thereof. Specifically, trial calculations were performed on LCA and damaging characteristics of photovoltaic systems, and reducible amount of carbon dioxide emission. Taking up thin film CdTe cells as the object, estimation was made on the energy payback time (EPT) and CO2 emission amount. The production scale ranges over 10 MW/ 30 MW/ 100 MW annually, the useful life is 20 years, and the unit requirement for CO2 emission originated from the charged electric power is 114 g-C/kWh. The EPT was 1.74 in the annual production of 10 MWp, 1.08 in 100 MWp, the unit requirement for CO2 emission was 14.0 in the annual production of 10 MWp, and 8.9 in 100 MWp. This is one of severals of that in the existing power supply source. For heavy metals, particularly Pb, the trial calculation resulted in 0.15 g/Wp in the crystalline type, and 0.1 g/Wp in the amorphous type. The problem therewith is separation and recovery. The reducible amount of carbon dioxide, or in other words, the amount of power that can be generated latently is 37,235 GWh/year, or 3.10 million tons when converted into carbon dioxide. (NEDO)

FY 1998 report on the results of the R and D of ITS technology using clean energy vehicles. R and D of the urban/residential area joint utilization system and advanced travel management/information supply; 1998 nendo clean energy jidosha wo mochiita ITS gijutsu no kenkyu kaihatsu. Toshinbu oyobi jutakuchi kyodo riyo system narabi ni soko kanri joho teikyo no kodoka no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The purpose of the project in FY 1998 is 'Experimental verification for EV spread promotion.' Two of a 3-month experiment were conducted in Yokohama MM21 area (Yokohama, Kanagawa) and in Tama Newtown (Inage, Tokyo) using a total of 100 (50 each) small EVs. The development was aimed at of an urban type rental-car system in Yokohama and of a car-sharing type second-car system for residential in Inage. As to these responses to ITS technology, the basic vehicle operation system was made common in both areas, and the daily use system was made a regional system considered of purposes of use, regional characteristics, etc. The experimental verification was worked on as almost expected in terms of the vehicle management, monitor assessment, responses from persons concerned in both areas. Therefore, it is said that the R and D have almost reached a point where there can be seen a possibility of system commercialization. Through the experimental verification, the development was able to be smoothly promoted of the basic technology and element technology which are thought to be needed for the commercialization of EV. From the experience of this experimental verification, it is judged that it is desirable to tackle the commercialization by a membership system when the commercialization of EV joint use system is planned in future. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the synthesis and processing of advanced biomaterials (fixation and effective utilization of carbon dioxide using peptides); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu (peptide oyo nisanka tanso koteika yuko riyo gijutsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In fiscal 1997, study was made on formation of peptides with a biogenic function and molecular recognition function, and peptide materials. The existing automatic design technique of peptides including non-natural amino acids was applied to design of complementary peptides of proteins with known structures to optimize a development technique of ligand. Practical function of peptides as advanced receptor ligand was verified by applying the existing conformation control technique to stable holding of peptide active conformation. Creation of bio-materials, and development of preparation technology of bio-substrates and materializing technology of functional molecular materials were carried out. To construct an electron transfer system by self- organized body of peptides formed on a substrate, a peptide molecular device was prepared and verified using linkers. To use peptides as photoelectron functional molecule, metallized peptide with main helix structure was prepared. The possibility of molecular materials with a fixation function of CO2 was examined. A high-sensitivity bio-sensor was also mentioned. 75 refs., 130 figs., 25 tabs.

Achievement report for fiscal 1993. International clean energy system technology to utilize hydrogen - WE-NET (Sub-task 5. Development of hydrogen transportation and storage technology - Edition 3. Development of liquid hydrogen storage facility); 1993 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) (Sub tusk 5: Suiso yuso chozo gijutsu no kaihatsu - Dai 3 hen. Ekitai suiso chozo setsubi no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

With an intention to establish a technology required to build a hydrogen storage tank with a storage capacity of 50,000 m{sup 3} as the target shown in the basic plan for WE-NET, the current fiscal year has performed the technical literature surveys to identify the existing technologies. In the survey on the similar large storage system, a liquefied natural gas (LNG) was taken up, and the survey on the LNG bases in Japan was carried out. With regard to the existing liquefied hydrogen storage system, surveys were performed on the test site for developing the liquefied hydrogen/liquefied oxygen engines, the rocket launch sites, and liquefied hydrogen manufacturing plant. In relation with peripheral technologies for the underground storage tank being an excellent anti-seismic form, the LNG underground storage facilities were surveyed. Regarding the rock mass storage tank, surveys were carried out on the LPG rock mass storage having been used practically, and the LNG rock mass storage that is in the demonstration phase. In the research on storage facilities, surveys were executed on the forms and heat insulation structures of the similar large low-temperature storage tanks, the use record of the existing liquefied hydrogen storage tanks, heat insulating materials, and heat insulating structures. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Research and development of solar beam power generation and utilization systems and ancillary technologies (Investigations and researches on large-size energy supply system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (ogata energy kyokyu system no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective to propose large-size system development scenarios assuming installations in deserts, the following investigations have been carried out: (1) collection of data on societies, economy, and energies in China and other countries where the large systems are assumed to be installed, (2) in order to reduce the costs, comparison was given on power generation cost by using a fixed tracking frame, a single axial tracking frame, and a biaxial tracking frame, (3) in order to evaluate the life cycle, discussions were given on the required energy inputs for system equipment, transmission and transformer equipment, and the installation construction to estimate the energy payback time (EPT) and CO2 emission unit requirement, and (4) discussions on development scenarios. In Item (1), while China expects on natural gas and atomic energy as the supply source, 80% of the energy would be supplied from coal in 2010. The development of new energies in India would further be delayed than in China. In item (2), the trially calculated power generation costs in Mongol by using the fixed frame, single axial tracking frame, and biaxial tracking frame were 8.72, 8.23 and 6.94 yen per watt. In Item (3) The EPT was two years or less in a 100-MW system, and the CO2 emission unit requirements in the silicon systems were 10 to 19 kg-C/kWh. (NEDO)

Achievement report of projects in fiscal 2000 for measures on technologies to fix and utilize effectively carbon dioxide. Development of program system technologies to fix and utilize effectively carbon dioxide - researches on key technologies (Developing technology to fix carbon dioxide electrochemically); 2000 nendo program hoshiki nisanka tanso koteika yuko riyo gijutsu kaihatsu (kiban gijutsu kenkyu) seika hokokusho (kokaiyo). Nisanka tanso no denki kagakuteki koteika gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to prevent global warming, research and development has been made on a carbon dioxide fixation technology using electrochemical means. This paper summarizes the achievements in fiscal 2000. In the research of a technology to return carbon dioxide to hydrocarbon such as methane electrochemically utilizing the high concentration carbon dioxide-methanol system, basic studies were performed on electrolytic reduction of CO2 using a methanol solvent system, and experimental studies were executed on high-speed reduction of carbon dioxide using gas diffusion electrodes. In the basic property experiment on diamond electrodes, high carbon dioxide reduction activity was obtained by having copper carried in the diamond electrode. In the CO2 electrolytic reduction experiment on three-phase interface using a copper net electrode, CO, ethylene, and methane were produced, while the electrode has retained the activity for an extended period of time, and the CO2 conversion rate reached about 66%. In structuring an electrochemical carbon dioxide fixation system, specifications for the CO2 electrolytic reduction equipment were determined, design, manufacturing, and electrode materials were selected, supporting electrolytes were discussed, and the entire system flow and liquid resistance were discussed. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Research and development of solar beam power generation and utilization systems and ancillary technologies (Development of ancillary devices for AC modules); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (AC module yo shuhen sochi no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Reasonability evaluation was progressed on the fundamental technologies having been proposed in fiscal 1998, and development was made on elementary technologies required for system structuring. The proposals made in fiscal 1998 include the deepening of the evaluations on effectiveness of AC modules, long-term stability evaluation on the system control schemes, trial fabrication and evaluation on AC battery modules, and development and installation of 2-kW demonstration facilities. In the effectiveness evaluation, discussions were given not only on advantages, but also on disadvantages. As the advantageous point, theoretical analyses were progressed on the effect of reducing the output drop due to shading, which was made clear by providing values. Effects of increase in switching units on electric wave interference as a disadvantage were made clear. As a form that can be applied consistently from an independent power source to a system coordination system, a flexible system using the module system comprising of AC modules and AC batteries was proposed as an effective utilization measure. A proposal was also made on an autonomous discrete type system control scheme as a control system that has sufficient expandability, and is durable against disasters. (NEDO)

FY 1996 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (Keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

Organosilicon polymers are highly innovative materials having high performance and novel functions, and they can be widely applied. The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis of highly conjugated polymers is investigated. In (2), novel organosilicon polymeric materials have been developed, which would be applicable to direct lithography of electronic circuits, and which could contribute to simplification of the circuit formation process. In (3), the research aims at development of new silicon-based polymer materials with luminescent function which can be applied to the large size electro-luminescent display devices. In (4), new materials with visible light absorption have been synthesized through the molecular design and synthesis. The photo-carrier generation was observed. 107 refs., 86 figs., 23 tabs.

FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on R/D of organosilicon polymers; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (keisokei kobunshi zairyo no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The purpose of this study is to establish fundamental techniques for molecular design, synthesis, material processing and evaluation of organosilicon polymers having excellent electro- and photo-functions, and advanced heat-proof, fire-proof and mechanical properties. This R/D includes (1) R/D of electrical conducting materials by organosilicon polymers, (2) R/D of novel organosilicon polymers applicable to direct lithography, (3) R/D of new silicon-based polymer materials with electro-luminous function, and (4) R/D of silicon-based polymers for new photoconductive materials. In (1), synthesis method of regular polymers with a 3-D structure was developed. Non-volatile dopants were developed, and structures of polymer-dopant composites could be controlled. In (2), precise control of conductivity was examined. Material processing and evaluation techniques were also examined through stabilization of polysilane thin films, optimization of pattern forming conditions, and precision of patterns. In (3), new silicon-based polymers have been synthesized. In (4), two kinds of polymers have been synthesized for development of materials with high photo-carrier generation efficiency and high mobility. 72 refs., 71 figs., 22 tabs.

Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 1. Survey/study concerning system evaluation); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 1. System hyoka ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the aim of formulating a strategy for introducing hydrogen, assessment was carried out on the energy consumption, environmental impacts and cost effiectiveness concerning various hydrogen utilization systems. In regard to soda-electrolysis by-product hydrogen and coke-oven by-product hydrogen, hydrogen supply capacity and cost effectiveness were evaluated. As a result, the two systems were found to have an annual hydrogen supply capacity of 11.52 GNm{sup 3} in total. As to the cost effectiveness, transportation by pipeline was 34 yen/Nm{sup 3}-H{sub 2} in the case of soda-electrolysis by-product hydrogen, and 40 yen/Nm{sup 3}-H{sub 2} in the case of coke-oven by-product hydrogen. An estimated cost of power generation showed 56 yen to 67 yen/kWh in such a system on remote islands as replacing diesel power generation by wind power generation, storing part of the electric energy produced in the form of hydrogen through water electrolysis, and using it as fuel for power generation by the fuel cell unit if wind conditions are unfavorable. Power generation cost on remote islands at present is sometimes in excess of 50 yen/kWh; therefore, this combined system showed promising results. The cost of using wooden biomass was estimated to be 51,000 yen/TOE , whose competitiveness is uncertain. (NEDO)

FY 2000 report on the results of the R and D of the technology for rationalization of energy utilization and for CO2 fixation using recycled paper; 2000 nendo energy shiyo gorika koshi nado yuko riyo nisanka tanso koteika gijutsu kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In this R and D, the recycled paper, etc. composed mainly of cellulose are degraded (saccharified) up to saccharides in a biological method. The saccharides and CO2 obtained are converted into useful substances such as organic acid using the bacterium function. The aim of the R and D is to develop this conversion (bioconversion) technology and to establish the technology to make an effective use of the recycled paper, etc. as useful chemical raw materials/substances and energy. In FY 2000, study was made mostly of the saccharification and bioconversion. As to the saccharification, conducted were the collection of the bacteria for cellulose degrading enzyme production which have been found so far and the evaluation of degradation of the recycled paper. And, as to the bioconversion, conducted were the survey and isolation of enzyme proteins and genes which are concerned in it in the process toward the formation to organic acid from saccharides and CO2, and the analysis of part of them. In this report, introductory remarks were described in Chapter 1. In Chapter 2, the results were summarized of the study on saccharification of the recycled paper. In Chapter 3, the results were outlined of the study on the bioconversion technology. This technology development was aimed at establishing new high efficiency bio-processes. (NEDO)

FY 1998 annual summary report on International Clean Energy Network Using Hydrogen Conversion (WE-NET) system technology. Subtask 6. Development of cryogenic temperature materials technologies; 1998 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 6 (teion zairyo gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Summarized herein are the cryogenic temperature materials technologies for the International Clean Energy Network Using Hydrogen Conversion (WE-NET) project, developed in FY 1998. The R and D programs have been implemented continuously since 1994. For stainless steel, the base and TIG weld metals were evaluated for their material characteristics in liquid hydrogen. The items investigated included the influences of hydrogen charge, 20% of stretch working on the base metal, welding methods, and ?-ferrite content on the characteristics. Fatigue strength of the base metal was found to increases as temperature decreases, but remain unchanged in a range from 20 to 77K. No significant difference was observed between 304L and 316L. For aluminum alloy, mechanical characteristics, centered by fatigue characteristics, were investigated for the base and weld metals. The sample of higher tensile strength showed a higher fatigue strength, at room temperature, 77 and 4K. The other tested items investigated included embrittlement characteristics in a hydrogen atmosphere, phase transformation, hydrogen diffusion and fracture toughness, for establishing the databases of cryogenic temperature materials. (NEDO)

FY 1999 report on the results of the R and D of genom informatics technology. Development of measures for stabilized supply of petroleum using compound living organisms; 1999 nendo genom informatics gijutsu kenkyu kaihtsu seika hokokusho. Fukugo seibutsukei riyo sekiyu antei kyokyu taisaku kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In this R and D, studies were made on the following: 1) comparative analysis of genes - a system based on PCR coupled with high-speed and high-throughput fragment analyzer; 2) development of the system which detects SNPs rapidly; 3) study of the technique for DNA analysis and comparison of DNA sequence by use of the triple-stranded DNA formation; 4) improvement of a genomic DNA subtraction method, the In-Gel Competitive Reassociation technique; 5) development of computer simulation system which has capability of predicting changes in gene expression; 6) development of a workbench system assisting at gene regulatory network construction; 7) analysis of a gene expression control network; 8) general R and D issues. In 1), PCR method was developed to confirm the principle. In 2), micro plant was developed. In 3), new long cDNA library was constructed. In 4), basic experiment on FRET technology was conducted. In 5), basic model was developed of clock gene expression oscillation simulation. In 6), system was developed of gene information subtraction. In 7), workbench was designed for support of transcription control network analysis. (NEDO)

Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Survey by region/industry in India; Kankyo chowagata sekitan riyo system kanosei chosa. Indo ni okeru sekitan riyo gaikyo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A survey was made in India which is a coal producing/consuming country following China in Asia and where coal is used for about 60% of the primary commercial energy. The survey was conducted on coal production/distribution/utilization and environmental issues, aiming at studying feasibility of introducing the environmentally friendly coal utilization system into every industry including the residential/commercial one, and at implementing a comprehensive master plan including Japan`s international cooperation. Total power source facilities in fiscal 1995 are 83.3 million kW, 64% of which are coal thermal power facilities and generated 260 TWh, 69% of the total output energy. Main commercial energy sources are coal, oil and natural gas, and oil is self-sufficient. The survey this time did not examine very well the actual state of the environmental pollution problem caused by the coal utilization. Indian coal is high in ash content but low in sulfur content, and therefore, SOx polluting air has not been a very important problem so far, but soot/smoke is almost the problem. Further, ash treatment after combustion at boilers, etc. is expected to be a big problem in the future. 49 figs., 88 tabs.

6th Conference on Coal Utilization Technology; Dai 6 kai sekitan riyo gijutsu kaigi koenshu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

The paper compiled the papers presented in the 6th Conference on Coal Utilization Technology held in September 1996. With relation to the fluidized bed boiler, reported were Field operation test of Wakamatsu PFBC combined cycle power plant and Development of pressurized internally circulating fluidized bed combustion technology. Regarding the coal reformation, Development of advanced coal cleaning process, Coal preparation and coal cleaning in the dry process, etc. Concerning the combustion technology, Study of the O2/CO2 combustion technology, Development of pressurized coal partial combustor, etc. About the CWM, Development of low rank coals upgrading and their CWM producing technology, Technique of CWM distribution system, etc. Relating to the coal ash, Engineering characteristics of the improved soil by deep mixing method using coal ash, Employment of fluidized bed ash as a basecourse material, On-site verification trials using fly ash for reclamation behind bulkheads, Water permeabilities of pulverized fuel ash, Separation of unburned carbon from coal fly ash through froth flotation, Practical use technology of coal ash (POZ-O-TEC), etc

Collection of outlines of Sunshine Program achievement reports for fiscal 1988. Solar energy (Light utilizing technology and heat utilizing technology); 1988 nendo sunshine keikaku seika hokokusho gaiyoshu. Taiyo energy (hikari riyo gijutsu / netsu riyo gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-04-01

Collected concerning the research and development of photovoltaic power systems are the basic research on solar cells; research and development of new-type photovoltaic power systems; and research and development of amorphous solar cells. Collected concerning the development of technologies for the practical application of photovoltaic power systems are the experiment, refining, and verification of low-cost silicon; experiment, fabrication, and verification of solar panels; research on the practical application of high-efficiency crystal-based solar cells; research and development of amorphous solar cells; research and development of solar cell evaluation systems; development of peripheral technologies; research and development of photovoltaic power-aided systems; research and development of centralized photovoltaic power systems; and development of photothermal hybrid type photovoltaic power systems. Collected concerning heat-utilizing technologies are the research and development of solar thermal electric power generation systems; research and development of solar air-conditioners and hot water supply systems; and development of practical application technologies for industrial solar systems. Collected also are international cooperative projects on solar energy technologies. (NEDO)

Collection of outlines of Sunshine Program achievement reports for fiscal 1989. Solar energy (Light utilizing technology and heat utilizing technology); 1989 nendo sunshine keikaku seika hokokusho gaiyoshu. Taiyo energy (hikari riyo gijutsu / netsu riyo gijutsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-04-01

Collected concerning the research and development of photovoltaic power systems are the basic research on solar cells; research and development of new-type photovoltaic power systems; and research and development of amorphous solar cells. Collected concerning the development of technologies for the practical application of photovoltaic power systems are the research on the practical application of new-type solar cells; research on the practical application of amorphous solar cells; research and development of solar cell evaluation systems; research and development of peripheral technologies; research and development of photovoltaic power-aided systems; research and development of centralized photovoltaic power systems; and research and development of photothermal hybrid photovoltaic power systems. Collected concerning heat application technologies are the research and development of solar thermal energy systems; development of practical application technologies for solar systems for industrial use etc.; and cooperative projects between Japan and Australia etc. on solar energy technologies. (NEDO)

Development in fiscal 1999 of technology to put photovoltaic power generation system into practical use. Management of research and development (System development committee working group); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri (system kaihatsu bukai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

This paper reports activities carried out in fiscal 1999 by the system development committee working group, a subordinate organization of the committee for development of the photovoltaic power generation technology. The items of implementation laid with emphasis in the current fiscal year included deliberations on the research achievements of the projects completed in fiscal 1999, on the research achievements of the new projects during fiscal 1999, and on pre-final evaluation of the development of a technology to put photovoltaic power generation system into practical use. The themes on the progresses in fiscal 1999 reported in March 2000 consisted of the followings: research and development of a system evaluation technology, investigation and research on supply capability evaluation on the photovoltaic power generation system, researches on peripheral devices for AC modules, investigation and research on electric safety of the photovoltaic power generation system, investigation and research on long-term reliability of inverters, investigation and research on meteorological data for optimal design, investigation and research on evaluation of the photovoltaic power generation, research on a photovoltaic power generating multi-hybrid system, research on a high-density linkage technology, and demonstrative research on a solar beam micro-hydraulic hybrid system. (NEDO)

Fiscal 1996 comprehensive report on R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu sokatsu hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

R and D was conducted on technology for composite thin film formation such as laser MOCVD, for thin film lamination, and for synthesis reaction and characterization in compounded fields where temperature/pressure/magnetic field/electrical field, etc., are compounded, for the purpose of creating materials with functions newly added or reinforced by regulating compositions and structures through atomic/molecular orders. The R and D was conducted on 24 themes, which were rearranged into four categories. Examples of the themes are as follows; development of super hard permanent magnets by crystallization process control of Nd-Fe-B amorphous alloys, as for structural control technology; research on high functional thin film sensors (PbLaTiO{sub 3}) using laser MOCVD, and research on ultra thin film by multi-ion-beam sputtering with ion/photo irradiation, as for thin film technology; R and D on highly ordered structure control technology in electrode surface compounded reaction fields, as for compounded fields; and, research on diagnostic technique for compounded reaction fields by laser-ionization method, as for supporting technologies. (NEDO)

Report on achievements in proliferation project to assist introduction of environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998 (utilization facilities); Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo seika hokokusho. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo (riyo setsubi)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This paper describes the achievements of the discussions in fiscal 1998 on the utilization facilities related to the coal bed methane gas supply plan for the city of Tieling in China. The gas quality standard calls for 3,500 kcal/m{sup 3} or more (methane concentration of 41% or higher). The supply is planned to start in December 1999, and continue the supply of 141,000 Nm{sup 3}/day in 2000, and 212,000 Nm{sup 3}/day in 2001 and thereafter. A gas supply center to collect gases recovered from each mine will be installed in the vicinity of the existing gas holder located about 2 km east of the Tiefa Mining Bureau. The Japanese side bears the cost of installing a gas compression and transportation facility for gas supply to the city of Tieling, a monitoring system, and devices for comprehensive surveillance system. This paper shows the overall plan drawings, the drain separator room building plan, the plans for arranging devices in the machine room, and the piping scheme. In addition, the piping plan around the gas holder, and the basic device plan are shown. Also appearing in the paper are the machine summary drawings, summarized flow charts, gas holder plan, de-humidifier plan, and electricity and instrumentation plans. The main body and supporting structure for the gas holder, and the foundation strength calculation sheets are also shown. Descriptions are given also on the facilities to deal with variation in demand quantity and supply quantity. (NEDO)

Fiscal 1998 industrial science and technology R and D project. Research report on R and D of genome informatics technology (Development of stable oil supply measures using complex biosystem); 1998 nendo genome informatics gijutsu kenkyu kaihtsu seika hokokusho. Fukugo seibutsukei riyo sekiyu antei kyokyu taisaku kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report describes the fiscal 1998 result on development of genome informatics technology. As comparative analysis technique of genes, the combination of electrophoresis and PCR was used. For improvement of the throughput and reproducibility of the technique, module- shuffling primers were used, and the multi(96)-arrayed capillary fragment analyzer was devised. The system detecting SNPs rapidly was also developed successfully. As analysis technology of DNA sequence by use of triple- stranded DNA formation, study was made on construction of long cDNA libraries, selective subtraction of specific sequences from libraries, and the basic technology of homologous cloning. Study was also made on each reaction step of IGCR technique for fast analysis, and specifications of a fluorescence transfer monitor. As modeling technique of genetic sequence information, the simulation model was developed for gene expression regulatory networks during muscle differentiation, and feedback regulation of period genes. Such support systems as transcription factor prediction and gene regulatory network inference were developed from existing data. (NEDO)

Report of FY 1997 on the international cooperation project. Survey of globalization of the effective energy resource utilization technology (development of high-accuracy acceleration measurement system); 1997 nendo kokusai kenkyu kyoryoku jigyo. Energy shigen yuko riyo gijutsu kenkyu kokusaika chosa (koseido kasokudo keisoku system no kaihatsu chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This report describes effectiveness of a system for measuring the acceleration and force in high accuracy by combining a laser interference meter and a vibration stand. A possibility of pressure sensitive paper to the impact force measurement in the collision examination is also described. The results obtained in FY 1997 are as follows. For the investigation of calibration system of acceleration and force sensor, one-dimensional interferometer system has been developed, which is standardized in ISO5347 accelerometer calibration. Thus, an interference fringe processing software has been made. Moreover, construction of a three-dimensional interferometer system has been started. For the characterization evaluation of pressure sensitive papers, it was succeeded in obtaining an elasticity wave pulse maximum about 1 msec by adopting the flight body made of resin. As a result, evaluation of the force sensor in the frequency area has become possible. To calculate the displacement of a body structural material in the collision experiment, an acceleration sensor has been made for trial purposes. For the international research cooperation, the working plan of a joint research with US Texas Christian University has been concluded. 11 refs., 73 figs., 23 tabs.

Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

Development of artificial soft rock. Jinko nangan zairyo no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kishi, K.; Nishioka, T. (The Tokyo Electric Power Co. Inc., Tokyo (Japan)); Nojiri, Y.; Kurihara, H.; Fukazawa, E. (Kajima Corp., Tokyo (Japan))

1990-09-15

When a part of the ground is replaced with artificial materials in the construction of important structures on soft rock foundations, it is desirable for the artificial materials to have the rigidity equivalent to that of the surrounding ground and to be stable in the long term. The article reports a success in the development and utilization of artificial soft rocks satisfying the above conditions by using a raw material produced locally at the construction site. The soft rock aimed at was mudstone belonging to the Neocene period, and the artificial material of soil-mortal system is selected as the equivalent having the same physical properties. Improvements in selection of solidification agents and cohesive soil were especially contrived: taht is, a new material for solidification was developed by mixing blast-furnace cement and gypsum; and the mudstone on the site was used as the cohesive soil by slurrying it to adjust its grain size to homogeneous composition. The artificial soft rock resulting from the above contrivance showed excellent flow, self-leveling, and filling properties at the stage of fresh mortar, and the physical properties after hardning was very similar to those of the natural ground. The long-term stability was also confirmed by the tests on hydration reaction and environmental factors. 2 figs., 1 tab.

Development of aluminium pleasure boats; Arumisei pleasure boat no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tsuzuki, A. [Toyota Motor Corp., Aichi (Japan)

1999-10-01

In February 1997, Toyota entered the marine business, a new business sector for it, by marketing a 28-foot cabin cruiser PONAM-28, developed by utilizing its automotive technologies. When Toyota began studying the possibility of entering the marine vessel industry in 1990, its main focus was on the environment. Therefore, in terms of materials procurement for the designs, Toyota refrained from using thermosetting resins, as much as possible. Instead, the decision was made to use an easily recyclable aluminum alloy for the hull which amounts to one-fourth of the vessel's total weight. (author)

Development of field navigation system; Field navigation system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Ibara, S; Minode, M; Nishioka, K [Daihatsu Motor Co. Ltd., Osaka (Japan)

1995-04-20

This paper describes the following matters on a field navigation system developed for the purpose of covering a field of several kilometer square. This system consists of a center system and a vehicle system, and the center system comprises a map information computer and a communication data controlling computer; since the accuracy for a vehicle position detected by a GPS is not sufficient, an attempt of increasing the accuracy of vehicle position detection is made by means of a hybrid system; the hybrid system uses a satellite navigation method of differential system in which the error components in the GPS are transmitted from the center, and also uses a self-contained navigation method which performs an auxiliary function when the accuracy in the GPS has dropped; corrected GPS values, emergency messages to all of the vehicles and data of each vehicle position are communicated by wireless transmission in two ways between the center and vehicles; and accommodation of the map data adopted a system that can respond quickly to any change in roads and facilities. 3 refs., 13 figs., 1 tab.

Basic tests of a rotation seismograph; Kaiten jishinkei no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Matsubayashi, H; Kawamura, S; Watanabe, F; Hirai, Y; Kasahara, K [Nippon Geophysical Prospecting Co. Ltd., Tokyo (Japan)

1996-05-01

For the purpose of developing a rotational seismograph capable of measuring the rotational component of seismic waves, vibratory gyroscopes were installed in the ground for the measurement of vibration of the ground, and the measurements were compared with the values obtained from tests using conventional velocity type seismographs. In the experiment, the plank was hammered on the east side and west side. The seismographs were arranged in two ways: one wherein they were installed at 7 spots at intervals of 1m toward the south beginning at a position 3m south of the vibration source with their rotation axes oriented vertical, with velocity type seismographs provided at the same spots; and the other wherein three rotational seismographs were installed 3m south of the vibration source with their rotation axes respectively oriented vertical, in the direction of N-S, and in the direction of E-W, with a velocity type seismograph provided at the same spot. It was found as the result that the rotational seismograph has a flat band on the lower frequency side and that it may be applied to elastic wave observation across a wide band. Accordingly, it is expected that it will be applied to exploration that uses the SH wave, to structural assessment that uses the Love wave, and to collecting knowledge about the features of natural earthquakes. 2 refs., 8 figs.

Development of new catalytic materials; Shinshokubai zairyo no kaihatsu doko

Energy Technology Data Exchange (ETDEWEB)

Tatsumi, Takashi [Yokohama National Univ., Kanagawa (Japan)

1999-04-05

The catalyst fulfils large role for the solution of environmental problem, resources problem, and energy problem. It is popular to carry out the research, which intends to realize the new process of which the environmental loading is low by the new catalyst. And, the development of catalyst material, which demonstrates the function under the ultimate condition like the environmental catalyst, is required. The interest has leaned in also using the solid catalyst for the synthesis of fine chemical such as intermediate and perfume of the medical supply synthesis. In this paper, the following are described as a new catalyst material: Zeolite and development trend of meso porous molecular sieve explosively studied recently. The application to the reaction is also simply touched. (NEDO)

Development of mechanical brake assist; Mechanical brake assist no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Konishi, M; Shingyoji, S; Nakamura, I; Tagawa, T; Saito, Y; Ishihara, T; Kobayashi, S; Yoshida, M [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

We have recognized that there are drivers who cannot apply strong brake pedal force , in spite of the necessity of hard braking in emergencies. We have developed a `mechanical brake assist system` which assists drivers appropriately, according to the drivers` characteristics based on studying the characteristic`s of conditions of drivers applying the brake pedal force in emergency conditions. 2 refs., 7 figs., 1 tab.

Study on utilization of shallow sea area by building an alga field. Discussions on its utilization for cultivating Ulvales; Sojo zosei ni yoru senkaiiki riyo no kenkyu. Anaaosa no baiyo to sono riyo ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Tsuno, M.; Maebayashi, M. [Hokkaido Electric Power Co. Inc., Sapporo (Japan)

1997-03-25

Discussions were given on mass cultivation in a water tank using sea water of an alga Ulvales used as feed for sea urchins and abalone. A fertilizer composed of ammonium sulfate and superphosphate of lime was used, and a water temperature was set as the environmental condition. Two kinds of Ulvales produced in different areas were used. One of the two kinds had full growth periodical and weight increasing rate low, but the other Ulvales had high weight increasing rate and no blights in alga bodies, and was found suitable for mass production. The result of a test on stocks of the latter species may be described as follows: multiple regression formulas for harvest, water temperature and illumination intensity were introduced for each cultivating condition for four cases regarding accommodation density and harvest frequency; and if a cultivating condition by which the harvest is maximized is adopted, a one cubic meter water tank placed on a place with good sunlight may be expected of producing as much harvest as 2181 grams at water temperature of 15{degree}C and 4899 grams at 25{degree}C. The cultivation requires the following precautions: aeration is required; sea water should be introduced into the tank; a mixed fertilizer with ratio of ammonium sulfate at 100 to superphosphate of lime at 15 may be used; water temperatures suitable for mass cultivation are 13 to 15{degree}C or higher; and light must be irradiated evenly. 14 refs., 9 figs., 5 tabs.

Report on a survey in fiscal 1999. Supplementary survey on research and development of carbon dioxide fixation and effective utilization technologies utilizing bacteria and algae (the survey on feasibility of bio-technologies to create economic effects, such as the biological CO2 fixation technology); 1999 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu futai chosa. Keizaiteki koka wo soshutsusuru seibutsuteki CO{sub 2} koteigijutsu nado no biotechnology no kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Bio-technologies including the biological CO2 fixation technology, or the green bio-technologies (GBT) are the technologies indispensable in realizing the change to a resource circulating and environment harmonizing society that accompanies economical growth, or in other words, the 'sustainable development'. In quantifying the feasibility of these technologies, the GBTs that contribute to creating Japan's international competitive power and employment were specified, and an approach to establish the realization target in 2010 was adopted, upon identifying the general condition of the related markets inside and outside the country. The GBT is the technology that makes the best use of Japan's independent strength created by combining the enzyme engineering and fermentation engineering with the 'genome science' (HEART). The targets are to substitute four million kiloliters of petroleum with a resource circulation type energy generated by the bio-technology; apply the bio-technology to about 30% of products and processes produced or used in Japan's chemical industries; and aim at creating markets by using environmental measurement and analysis, treatment of hard-to-decompose substances, and supports on tree planting as the three pillars. A simulation on return on investment in GBT business suggests the effect of promoting PFI. (NEDO)

Report on a survey in fiscal 1999. Supplementary survey on research and development of carbon dioxide fixation and effective utilization technologies utilizing bacteria and algae (the survey on feasibility of bio-technologies to create economic effects, such as the biological CO2 fixation technology); 1999 nendo saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu futai chosa. Keizaiteki koka wo soshutsusuru seibutsuteki CO{sub 2} koteigijutsu nado no biotechnology no kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Bio-technologies including the biological CO2 fixation technology, or the green bio-technologies (GBT) are the technologies indispensable in realizing the change to a resource circulating and environment harmonizing society that accompanies economical growth, or in other words, the 'sustainable development'. In quantifying the feasibility of these technologies, the GBTs that contribute to creating Japan's international competitive power and employment were specified, and an approach to establish the realization target in 2010 was adopted, upon identifying the general condition of the related markets inside and outside the country. The GBT is the technology that makes the best use of Japan's independent strength created by combining the enzyme engineering and fermentation engineering with the 'genome science' (HEART). The targets are to substitute four million kiloliters of petroleum with a resource circulation type energy generated by the bio-technology; apply the bio-technology to about 30% of products and processes produced or used in Japan's chemical industries; and aim at creating markets by using environmental measurement and analysis, treatment of hard-to-decompose substances, and supports on tree planting as the three pillars. A simulation on return on investment in GBT business suggests the effect of promoting PFI. (NEDO)

Development of small-size transmission tower erection method; Kogata tetto kumitate koho no kaihatsu kenkyu (gaibushiki crane ni yoru kogata tetto kumitate koho no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Matsuishi, S.; Asano, J.; Koji, Y. [Kansai Electric Power Co. Inc., Osaka (Japan); Tsujimura, I.; Teramoto, A. [The Kanden Kogyo Incorporated, Osaka (Japan); Sasaki, T.; Mito, K. [AG Ajikawa Corp., Osaka (Japan); Tsuji, M.; Fukumoto, T.; Yamaguchi, N.

1997-09-30

To reduce the construction period and cost and to enhance the safety during 77 kV-class transmission tower election, a new method of small steel transmission tower erection using an external type crane has been developed. For the selection of cranes, a commercially available self-climbing crane was employed which has an operating radius of 11 m, a lifting load capacity of 1.5 t, and a lift of up to 60 m. For the space analysis using a model tower, various supporting methods with horizontal supporting members, stress analysis for each tower stub, and apparatuses were examined. For the demonstration tests of election using the model tower, strain gages were attached at each point of steel tower, crane and horizontal supporting members, to measure the stress of members at each stage of the election. It was confirmed that there were no problems. For the election of actual steel tower, the practicality of this method was compared with that of conventional methods. The construction period was reduced in 20%, and the cost was reduced in 4%. The safety of this method was drastically enhanced due to the lack of moving on the tower and less manual operation. 9 figs., 1 tab.

FY1997 geothermal development promotion survey. Development feasibility study 'Ashiro area'; 1997 nendo chinetsu kaihatsu sokushin chosa. Kaihatsu kanosei chosa (Ashiro chiiki) hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

With regard to the Ashiro Town area in Iwate Prefecture, this paper reports the result of evaluations based on temperature and pressure logging after a lapse of an extended period of time (well No.2) and a steam jet test (well No.1). These activities were performed as the survey on promotion of geothermal development and survey on development feasibility in fiscal 1997. As a result of the overall analysis based on the present survey and ones in the past, the geothermal system model in the surveyed area may be conceived as follows: in both of the N7-AR-1 and N7-AR-2 wells drilled in the southern part of the surveyed area, temperature as high as 250 degrees C or higher was confirmed; the underground temperature is 200 degrees C or higher at an altitude level of zero meter and 250 degrees C at around -500 m, leading to a belief that the high temperature area spreads to south; as a fracture system holding geothermal fluid, a fault was identified at the N7-AR-1 well drilling depth of 1710 m; in the steam jet test, a geothermal reservoir (a shallow geothermal reservoir) was confirmed to exist; the geothermal fluid that has jetted out shows alkaline Na-SO{sub 4} type; and the deep geothermal reservoir has high temperature and is presumed to be in the two-phase condition, presenting promising factors as the geothermal resources. (NEDO)

Current srate and problems in Japanese petroleum development. ; International trends in petroleum development and problems in Japanese devepment business. Waga kuni sekiyu kaihatsu no genjyo to mondai ten. ; Sekiyu kaihatsu no kokusai doko to waga kuni kaihatsu jigyo no kasai

Energy Technology Data Exchange (ETDEWEB)

1991-11-05

Petroleum production and its supply and demand require ever closer coordinations among the countries involved. On the other hand, however, there a large number of difficult questions as the problems of global environmental pollution and greenhouse effects increase their seriousness and the economic resources in the petroleum business become scarcer. This paper describes the current state of the Japanese petroleum development, the necessity of spontaneous petroleum development, the international trends in the petroleum development business, and the tasks for Japan in the petroleum development business. Japan is a late comer in the petroleum development business. There are such difficulties as sizes of oil fields being discoverd are becoming smaller, the natural conditions in development target areas are getting severer, and the economic effects are inferior. Japan, whose petroleum self-supply rate is about 0.3%, whose petroleum dependency is heightening as a result of increase in nuclear power generation, and who is the third largest petroleum consuming country next to the U.S.A and Soviet, must use efficiently her financial and technical powers to vitalize her spontaneous petroleum development. Japan has a duty to contribute to the world {prime}s future stabilized supply of oil. The Japanese Government has launched the five-year fund development plan to perform basic surveys for ail in the north-east part of the Japan Sea and the pacific Ocean.

Fiscal 1996 comprehensive report on R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu sokatsu hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

R and D was conducted on technology for composite thin film formation such as laser MOCVD, for thin film lamination, and for synthesis reaction and characterization in compounded fields where temperature/pressure/magnetic field/electrical field, etc., are compounded, for the purpose of creating materials with functions newly added or reinforced by regulating compositions and structures through atomic/molecular orders. The R and D was conducted on 24 themes, which were rearranged into four categories. Examples of the themes are as follows; development of super hard permanent magnets by crystallization process control of Nd-Fe-B amorphous alloys, as for structural control technology; research on high functional thin film sensors (PbLaTiO{sub 3}) using laser MOCVD, and research on ultra thin film by multi-ion-beam sputtering with ion/photo irradiation, as for thin film technology; R and D on highly ordered structure control technology in electrode surface compounded reaction fields, as for compounded fields; and, research on diagnostic technique for compounded reaction fields by laser-ionization method, as for supporting technologies. (NEDO)

Achievement report for fiscal 1993. International clean energy system technology to utilize hydrogen (WE-NET) (Sub-task 5. Development of hydrogen transportation and storage technology) (Edition 5. Development of hydrogen absorbing alloys for discrete transportation and storage); 1993 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) . Sub tusk 5. Suiso yuso chozo gijutsu no kaihatsu - Dai 5 hen. Bunsan yuso chozo you suiso kyuzo gokin no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Surveys and researches have been performed with an objective to accumulate knowledge required for R and D of a hydrogen transportation and storage technology. With respect to the hydrogen absorbing alloys for hydrogen transportation and storage, surveys have been carried out on the rare earth-nickel based alloy, magnesium based alloy, titanium/zirconium based alloy, vanadium based alloy, and other alloys. Regarding the hydrogen transportation and storage technology using hydrogen absorbing alloys, surveys have been made on R and D cases for hydrogen transporting containers, stationary hydrogen storing equipment, and hydrogen fuel tank for mobile equipment such as automobiles. For the R and D situation in overseas countries, site surveys have been executed on research organizations in Germany and Switzerland, the leader nations in R and D of hydrogen absorbing alloys. As a result of the surveys, the hydrogen absorbing alloys were found to have such R and D assignments as increase of effective hydrogen absorbing quantity, compliance with operating conditions, life extension, development of alloys easy in initial activation and fast in hydrogen discharge speed, and cost reduction. Items of the transportation and storage equipment have such assignments as making them compact, acceleration of heat conduction in alloy filling layers, handling of volume variation and internal stress, and long-term durability. (NEDO)

Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Research and development of solar beam power generation and utilization systems and ancillary technologies (Investigations and researches on meteorological data for optimal design); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (saiteki sekkei no tame no kisho data no chosa kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Observations are being made in Takasaki City, Gunma Prefecture on insolation, putting emphasis on the north side, and insolation by wavelengths to put insolation estimation model on the north side slope into order. This is an attempt to put into order by using the model the data for insolation on slope in all azimuth, taking the meteorological offices all over the country as the object. With regard to monthly average insolation, it was verified that the existing estimation model can be applied to the north slope in the Takasaki area, whereas trial calculations were performed on the average daily cumulative insolation by azimuth and inclination angle in the Takasaki observation points. As a result, it was made clear that the insolation onto north side roofs in Japan is about 70% of that on the south side. With respect to the time cumulative slope insolation, it was made clear that the Perez's cumulative model can be applied to the Takasaki area. Spectral distribution of global and scattered solar radiation was put into order by insolation to have verified that the stronger the global solar radiation intensity, the greater the occupation ratio of shorter waves increases, or in other words, the spectral distribution of the global insolation can be formulated. Sky distribution of radiation is being measured by means of measuring the sky scanning type radiation and luminance distribution. (NEDO)

Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 9. Development of liquid hydrogen transport and storage technology Part 3 (Concept design of hydrogen liquefaction facility); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu seika hokokusho. Task 9. Ekika suiso yuso chozo gijutsu no kaihatsu 3 (suiso ekika setsubi no gainen sekkei)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research result on the aerodynamic design and seal design necessary for development of advanced hydrogen compressors for large-scale hydrogen liquefiers in the WE-NET plan. In the study on aerodynamic performance of impellers, 3-D viscous flow analysis of 2 types of new impeller forms (20 and 15 degrees) was carried out based on the study result on backward angle. The 2-D viscous flow analysis result on diffuser suitable for hydrogen compressors showed that improvement of the performance of a NACA65 type profile diffuser is possible. The study result on scale effect by using Casy's evaluation formula showed the efficiency difference of nearly 2.6% between impeller diameters of 1000mm and 300mm at 0.08 in exit width ratio. Study was made on hydrogen gas leak for spiral groove sealing selected as hydrogen gas sealing. The study on small capacity hydrogen liquefiers was conducted on the same process cycle as the 11t/d liquefier which has been commercially available. (NEDO)

FY1995 generic supercritical water technology; 1995 nendo generic technology to shite no chorinkai riyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For the establishment of the basis of supercritical fluid technology, we perform elucidation of the specific feature of the supercritical fluid as a reaction media and development of some new process. In this study, we first studied the fluid structure of SCF through in-situ spectroscopy and MD simulation. As a result, significant hydrogen bonding amongst water molecules and a solvation structure around the solute were observed in the supercritical state. This fluid structure has new features different from that of high temperature steam or liquid water. We found that this is closely related to the difference of bulk properties of SCF and local one around the solute. On the basis of these fundamental findings and with the better understanding of the specific features of SCF as a reaction media, development of some new process had been conducted more efficiently and successfully. The processes being developed in this study include 1) waste biomass and plastic conversion to recover chemicals, 2) hydrogenation of heavy oil for desulphurization through partial oxidation 1 and 3) hydrothermal synthesis of metal oxide fine particles. (NEDO)

Performance test of solar energy distillation system; Taiyonetsu riyo kaisui tansuika system no zosui seino shiken

Energy Technology Data Exchange (ETDEWEB)

Kawahara, T; Toyoshima, Y [Keio University, Tokyo (Japan); Narasaki, Y; Kamiya, I [Ebara Corp., Tokyo (Japan); Sato, H [Keio University, Tokyo (Japan). Faculty of Science and Technology

1997-11-25

In order to develop a seawater desalination equipment utilizing solar heat, a performance test was performed on a three-stage solar heat vacuum distiller. The equipment can evaporate and condense water at low temperatures by reducing the pressure in a distilling section. Solar heat is collected by a heat collecting plate, by which water as the working fluid is evaporated and moved to a heat conducting section in an evaporation pipe in a state of steam. The steam is condensed in a low-temperature heat conducting pipe, the heat is released outside the heat conducting pipe, and seawater is evaporated under low pressure condition. The working fluid is circulated for repetitive use. Solar cells are used as a motive power source for a vacuum pump, hence the system is self-sustainable even if installed in a desert area and the like places. The construction is simple, highly durable, and easy in maintenance. The system has high water producing performance, uses no harmful substances whatsoever such as fluorocarbons, and is a friendly system to the global environment. Because of evaporation at low temperatures, heat loss to the surroundings and sensible heat due to temperature rise are small, and the system response is quick. The solar heat can be utilized more effectively as multiple effects. When a heat collecting plate of 7.76 m {sup 2} was used, maximum yield of 105.45 kg/day was obtained. The system`s distillation efficiency is higher than other types of solar heat utilizing distillers. 7 refs., 5 figs.

Production, property, and application of bacterial cellulose; Bakuteriaserurosu no seisan, butsusei no tokucho to sono riyo

Energy Technology Data Exchange (ETDEWEB)

Yamanaka, S.; Watanabe, K. [Ajinomoto Co. Inc., Tokyo (Japan). Central Research Lab.; Iguchi, M. [Agency of Industrial Science and Technology, Tokyo (Japan)] Nishi, Y. [Sony Corp., Tokyo (Japan)

1998-09-01

Cellulose produced by bacterial is called bacterial cellulose (BC). The morphology and physical properties of BC are found to be quite unique in comparison with those of higher class plants. The properties are elucidated and a study is made to utilize the properties. The outline of this study is introduced in the sequence of BC production, BC morphology, elucidation of the physical property, and study on the application. BC consists of ultrafine fibers, and the widths of fibers are in the range from (1/199) to (1/1,000) of cotton fibers, forming distinctive network structure. It is assumed that the high Young`s modulus is based on the structural features of BC. Researches have been made on various applications to such fields as audio, paper, food, and compounds where the features of cellulose are utilized effectively. The morphology of cellulose can be varied by adding drugs which can change a part of the protein. It is expected that cellulose structure can be controlled in the future by the application of this technology. 18 refs., 6 figs., 2 tabs.

CIM overview. (2). ; Architecture, infrastructure, information technology. CIM soron. (2). ; Architecture, infra, joho riyo shien gijutsu

Energy Technology Data Exchange (ETDEWEB)

Seryo, K [IBM Japan Ltd., Tokyo (Japan)

1991-12-10

The materialization of computer integrated manufacturing (CIM) requires an establishment of its systematizing system, i.e., architecturer and planning of the infrastructure to support it and basic engineering to support the informational utilization. The CIM architecture is classified into management and system structure, strategic planning method, System development introduction method, etc. The infrastructure aims at epoch-makingly heightening the productivity and speed by integrating the production planning, engineering design, accounting, sales, general business and affairs, production engineering, production activities, and activities of suppliers and clients. The informational utilization support engineering comprises the management support tool, decision making support tool, application development tool, etc. What is important is to establish a system of systematizing engineering in order not to be behind the strategic activation era of information to come. 17 refs., 4 figs., 1 tab.

Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in Indonesia; Kankyo chowagata sekitan riyo system kanosei chosa. Indonesia ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With relation to the coal of Indonesia, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/distribution/utilization and environmental problems, and analyzed the situation of the coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to work out a comprehensive master plan including Japan`s international cooperation for introducing the environmentally-friendly coal utilization system to Indonesia. Coal utilization systems, the introduction of which Indonesia should study in future, were picked up, according to the surveys in fiscal 1993 and 1994. In commercial/residential and small-scale industry sectors, needed is improvement of carbonization technology for production of coal carbonization briquette. Moreover, the introduction of bio-briquette should be studied in the future. In the power generation sector, studies should be made on the introduction of technology for SOx/NOx reduction and technology for coal ash treatment including the effective use of coal ash. For the introduction of coal boilers, the combustion mixed with bagasse, which is abundant in amount, is also necessary. In the coal production sector, coal preparation technology is studied, and a method to select the optimum process was proposed through the simulation. 76 figs., 43 tabs.

Aspiration toward geothermal energy utilization in regional development plan. Part 6. ; Hydrothermal fluid utilization business in Matsuo-mura of Iwate prefecture. Chiiki keikaku ni okeru 'chinetsu riyo' eno hofu. 6. ; Iwateken Matsuomura no chinetsu nessui riyo jigyo

Energy Technology Data Exchange (ETDEWEB)

Otobe, Y; Furutate, E

1992-10-31

Twenty six years have passed since the first geothermal power station was constructed in Matsuo-mura of Iwate Prefecture, Japan. This paper describes the history, the present situation and the future conception of the geothermal energy utilization in this village. This village includes Hachimantai of a vantage ground in the center and has the gross area of 233.8km[sup 2], the annual average temperature of 8.3 centigrade and the continuous snow cover period of about 100 days. The hot water leading facility was cooperatively constructed by Japan Metals and Chemicals, Hachimantai Hot Spring Development and Matsuo-mura. The total working expense is 539.3 million yen. Hot water sources are the condensate from the condenser of geothermal power plant and hot spring. This mixed hot water of 4.3 t/min is led to respective facilities. The hot water supplying channel has the length of 12.8km from the power station through the Hachimantai hot spring resort, Kamiyogi to Takaishino. Respective total areas of greenhouses using hydrothermal fluid in both districts are 1,075ha and the inlet temperature of hot water is 60 centigrade and kinds of crop are 5 like green pepper and others. Takaishino agricultural park has selected flower and ornamental plant culture such as poppy anemone, stock and statice which are suitable for this district of low temperature and insufficient sunshine. The planted area is 10,700m[sup 2]. 2 refs., 9 figs., 4 tabs.

Fiscal 1997 report on the R and D result of industrial science and technology. R and D on super metal (R and D on innovative raw metal materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Study was made on the applicability of mechanical milling (MM) and mechanical alloying (MA) to Fe system alloys. Metastable austenitic stainless steels such as SUS316L and SUS304L form {alpha} phases by strain induced transformation due to MM, and are subjected to further plastic deformation. Nano-size fine structure was obtained through inverse transformation into austenite({gamma}) by heat treatment or high-temperature sintering of MM powder. Fine microduplex structure of 620nm in average crystal grain size was obtained for SUS316L. This material showed nearly 3.3 times higher 0.2% tensile proof stress, nearly 1.8 times higher tensile strength, and 35% higher elongation than conventional ingot steels. Solid solution powder of 12Cr-Mo-W ferritic steel was sintered by hot isostatic pressing (HIP) under low- temperature and ultrahigh-pressure conditions of 650degC and 588MPa. The as-HIP`ed sample and sample annealed at 800degC showed average {alpha} grain sizes of 33 and 50nm, respectively, and a strength twice as high as that of 12Cr steel. 97 refs., 60 figs., 18 tabs.

Fiscal 1992 report on geothermal development promotion survey (Development of geothermal reservoir assessment technique); 1989 nendo chinetsu kaihatsu sokushin chosa (Chinetsu choryusou hyoka shuho kaihatsu hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Efforts were exerted in fiscal 1984-1992 to develop techniques for appropriately assessing a geothermal reservoir for its productivity for duly predicting the optimum scale of power generation to be provided thereby. In the development of simulators, geothermal reservoir simulators (SING-1, -2, -3) and a geothermal well 2-phase flow simulator (WENG) were developed. As for the treatment of fractures in a reservoir and of substances soluble in the hot water, the methods for dealing with them were improved and augmented. In a model field study in a Hokkaido forest, reservoir pressure continuous observation and monitoring, temperature logging and pressure logging for existing wells, and geothermal fluid chemical analysis were performed for reservoir analysis, in which both natural state simulation and history mapping excellently reproduced the temperature and pressure distributions. The temperature and pressure distributions in a natural state simulation, out of the results of an analysis of the Oguni district model field, Kumamoto Prefecture, agreed not only with those in the natural state but also with the pressure transition data in the observation well. (NEDO)

Fiscal 1997 R and D project under a consignment from NEDO. R and D of the femtosecond technology; 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Femto byo technology no kenkyu kaihatsu (femto byo technology no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Ultrahigh-speed electronic technology is indispensable for creating industrial basic technologies supporting the advanced information society in the 21st century. Control technology of photonic and electronic states in a femtosecond region is essential. To establish the development policy of generation and transmission devices for femtosecond light pulses, research and analysis were made on nonlinear optical response and light pulse transmission properties. Basic issues on devices and materials such as mode-locked semiconductor laser, pulse compression device and light-light modulation material for coding were extracted. For new femtosecond light pulse control/distribution devices, research and analysis were made on response properties of intersubband transition phenomena in a semiconductor and electron spin relaxation phenomena, and semiconductor quantum structure. To develop metrological technology using ultra-short light pulse, study was made on an evaluation method for time- fluctuation of pulses in 100 femtosecond level. Generation of femtosecond high-intensity X-ray pulse was possible by fine control of the existing high-intensity laser. 19 refs., 26 figs., 1 tab.

Fiscal 2000 achievement report on research and development of industrial technologies. Research and development of synergy ceramics (Development of energy use rationalization technology); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are made to develop self-complete type purification ceramic materials in which selection, separation, and purification functions are merged with the energy conversion function. Activities are conducted in the three fields of developing (1) materials derivation technology, (2) application technology, and (3) common base technology. In relation to selection, separation, and purification functions in field (1), studies are made about electrochemical cell structure control and cell constituting materials for enabling a high efficiency NOx purification reaction. As for the energy conversion function, studies are made about the improvement of characteristics of oxide based thermoelectric conversion materials and about changes in electrical output due to their development into cells. In a study of novel thermoelectric conversion materials, K{sub 2}NiF{sub 4} type Y{sub 0.33}Sr{sub 1.67}(Ni{sub 1-y}Co{sub y})O{sub 4-{sigma}} and Ce{sub 0.25}Sr{sub 1.75}(Ni{sub 1-y}M{sub y})O{sub 4-{sigma}} (M=Fe, Co) are synthesized, and electrical resistivity levels and Seebeck coefficients are determined at room temperature-800 degrees C in an oxygen current. Seebeck coefficients are found to be negative for all specimens, which shows that they are n-type conductors. Ce{sub 0.25}Sr{sub 1.75}(Ni{sub 0.7}Fe{sub 0.8})O{sub 4-{sigma}} exhibits the greatest output factor of 0.064 times 10{sup -4}Wm{sup -1}K{sup -2} (400 degrees C). (NEDO)

Fiscal 1993 report on results of R and D on innovative technology for producing advanced biomaterial. Peptide applied carbon dioxide fixation/effective utilization technology (First volume); 1993 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho. 1. Peptide oyo nisanka tanso koteika yuko riyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Technology is being developed for preparing functional materials by synthesizing new functional peptides in which non-natural amino acid needed for the functional manifestation is introduced, and by modifying the surface of a base plate such as silica glass by using such peptides. Activities were conducted in the three areas of (1) creation of functional molecules, (2) materialization technology, and (3) comprehensive investigation and research; the activities were carried out independently and parallelly in the first two areas. In (1), design technique for the structures and functions of peptides was developed, as were conformational control technique, synthesis of peptides having optical/electronic functions, peptide synthesis by an enzyme method, and R and D on introduction of non-natural amino acid into peptides; in (2), element technologies were developed such as substrate forming technique (pattern forming and thin film forming technology), substrate modification technique, development of reagent for binding peptide onto a substrate, and R and D on creation of biomaterials having molecular recognition function and its stabilization technique. In (3), progress control in promoting themes and a meeting for exchanging information were conducted, while survey on related element technologies was systematically and comprehensively carried out. (NEDO)

Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 2. Research on safety measures; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu seika hokokusho. Task 2. Anzen taisaku ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 WE-NET phase 2, task 2 research result on safety measures. In the study on preparation of the safety design standard, based on the concept design of the hydrogen supply station under investigation in task 7, latent anomalies and accidents, safety measures against them, and precautions for the safety design were arranged. Survey was made on databases available to collect failure rates necessary for quantitative risk assessment. In the study on establishment of a safety evaluation method, an evaporation apparatus for liquid hydrogen was prepared for comparative experiment with liquid nitrogen. Various information on flow and evaporation properties of liquid hydrogen were obtained. Survey was made on previously reported documents for hydrogen explosion experiment and preparation of an experiment plan. The simulation model for spillage, evaporation and diffusion of liquid hydrogen was verified and improved on the basis of the experiment results. A commercially available computation program for hydrogen deflagration was introduced, and its implementation was studied. (NEDO)

Fiscal 1994 report on results of R and D on innovative technology for producing advanced biomaterial. Technology of fixation and utilization of carbon dioxide using peptides; 1994 nendo senshin bio zairyo no sosei kako gijutsu no kenkyu kaihatsu seika hokokusho. Pepuchido oyo nisanka tanso koteika yuko riyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

R and D of a material was conducted that has a function of fixation of carbon dioxide for example, by synthesizing non-natural amino acids required for the manifestation of the function, incorporating the amino acids into new bio-functional peptides to be synthesized, and fixing the peptides on a substrate. Activities were carried out in three areas, which were (1) innovative technologies for producing functional molecules: R and D concerning structural and functional design of peptides, conformational control technique, preparation of peptides with photoelectric conversion function, peptide synthesis using enzyme, and method of incorporating non-natural amino acids into peptides, (2) R and D on materialization technologies of functional molecules: formation of film onto a substrate, pattern forming technique, substrate modification technique, peptide binding reagent or linker, and development of technologies for creation of biomaterials having molecular recognition function and their stabilization. and (3) comprehensive investigation and adjustment (operation of information exchange conference and adjustment of the progress). In (2), an examination was made on the effect of polymerization on functions, for example, by fixing molecular recognition peptides in monomers and polymers on a catalyst support. (NEDO)

Fiscal 1997 survey report. Subtask 8 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of hydrogen combustion turbines/development of combustion control technology); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system (WE-NET) subtask 8 suiso nensho turbine no kaihatsu nensho seigyo gijutsu no kaihatsi

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Concerning the development of hydrogen combustion turbines, the paper described the fiscal 1997 results. As a hydrogen/oxygen combustor, the annular combustor was studied. Based on the results obtained by the last fiscal year, a combustor for the evaluation test was designed/fabricated. Oxygen is mixed with vapor at the portion of the burner, rotated/jetted (flame held by the circulation flow generated) and made to burn with hydrogen (porous injection). The smooth ignition and equilibrium wall temperature distribution were made possible. Concentrations of the residual hydrogen/oxygen in the stoichiometric mixture ratio combustion were both less than 1%. Further, can type combustor I is a type in which hydrogen and oxygen are burned near the burner and then are diluted by vapor. Improved of the burner structure and diluted vapor hole, it was tested. In can type combustor II, a mixture of oxygen and vapor is supplied and burned with hydrogen. The appropriate supply of oxygen was 20% distribution to the primary scoop and 80% to secondary. In both combustors, smooth ignition was possible, and concentrations of the residual hydrogen/oxygen in the stoichiometric mixture ratio combustion were controlled at minimum (approximately 1%). The evaluation method for the optimum hydrogen/oxygen combustor was studied. 142 figs., 24 tabs.

Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in the Philippines; Kankyo chowagata sekitan riyo system kanosei chosa. Philippines ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With relation to the coal of the Philippines, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/development, the trend of coal import and domestic distribution, the coal utilization trend, and environmental problems, and analyzed the situation of coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to draw up a master plan for the introduction of the environmentally-friendly coal utilization system. As to the use of environmentally-friendly coal technology which should be adopted to the coal mining industry and commercial/residential sector, cited are the introduction of coal preparation technology and power transmission technology, and the development/spread of briquette as a firewood substituting fuel. In the electric power sector, the problem is the treatment of ash after combustion and the effective use. Relating to the treatment of flue gas, there is no installation at all of desulfurization facilities and denitrification facilities. In the cement industry sector, they wish to return fuel from heavy oil to coal. For it, it is necessary to study dust preventive measures. In the other sectors, coal hasn`t been used very much. An increase in coal demand is not expected also in the future, and big problems concerning coal haven`t occurred. 42 figs., 64 tabs.

Development of air fuel ratio sensor; A/F sensor no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sakawa, T; Hori, M [Denso Corp., Aichi (Japan); Nakamura, Y [Toyota Motor Corp., Aichi (Japan)

1997-10-01

The Air Fuel Ratio Sensor (A/F sensor), which is applied to a 1997 model year Low Emission Vehicle (LEV) was developed. This sensor enables the detection of the exhaust gas air fuel ratio, both lean and rich of stoichiometric. It has an effective air fuel ratio range from 12 to 18 as required for LEV regulation. It has the fast light off, - within 20 seconds - to minimize exhaust hydrocarbon content. Further, it has fast response time, less than 200 msec, to improve the air fuel ratio controllability. 3 refs., 7 figs.

Development of a water hydraulic servovalve; Suiatsu servo ben no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Urata, E.; Nakao, Y. [Kanagawa University, Kanagawa (Japan). Faculty of Engineering; Yamashina, C.; Miyagawa, S.; Usami, Y.; Shinoda, M. [Ebara Research Co. Ltd., Kanagawa (Japan)

1997-06-25

An electrohydraulic servovalve that uses clear water as a pressure medium (water hydraulic servovalve) is developed. A conventional electrohydraulic servovalve cannot work with this hostile fluid. This paper explains the structure and functions of components, and the relationship between them, as well as development procedure of the water hydraulic servovalve. The basic idea for the development is to support the spool of the valve with hydrostatic bearings and to lead the water from the bearings to the flapper-nozzle system, which, in this valve contains a laminar restriction upstream from the nozzle instead of the turbulent restriction in the conventional flapper-nozzle system. This paper also explains the design procedure of the hydrostatic bearing in the valve and the connection of electromagnetic elements and the fluidic elements. The manufactured water hydraulic servovalves show good characteristics in their smooth motion, endurance and controllability, including dynamic characteristics. 25 refs., 12 figs.

Development of MCFC and PEFC technologies; Jisedai nenryo denchi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Hori, M; Ozu, H; Sonai, A [Toshiba Corp. Tokyo (Japan)

1996-06-01

Next-generation fuel cells under development by Toshiba Corporation are outlined. The molten carbonate fuel cell (MCFC) has become stable in performance, which results from the conversion of the matrix group from the {gamma}-type to {alpha}-type LiAlO2. The cathode material is expected to withstand the elution of electrolyte for 20000 hours. The soft structure separator developed for stack constitution is expected to improve electrical contact and reduce the cost of stack. An appliance has been completed to tentatively produce every element concerned. During an actual operation, the structural soundness of the 2-cell stack was confirmed by thermal load tests. As for the polymer electrolyte fuel cell (PEFC), an interior humidification method has been developed using a porous material for supplying water to the polymer film. The amount of moisture can be controlled, which will enable a larger-area cell. A 1kW-class stack with a world-record-level 1200cm{sup 2} electrode area has been developed, which stack has shown that the target output has been attained. Furthermore, the power generation efficiency of the system including fuel treatment has been examined. 10 figs.

Power conditioner without isolation transformer; Toransuresu power conditioner no shohin kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Okado, C; Itami, T; Kimoto, K [Toshiba Corp., Tokyo (Japan)

1996-10-27

A light-weight downsized and high efficiency transformer-less type 4 kW power conditioner (inverter) has been developed. This power conditioner insures the system interconnection protection by monitoring the voltage of two single-phase three-line circuits. The power conditioner has weight of 17.5 kg and efficiency of 94%. Potential fluctuation of photovoltaic cells due to the switching of power devices at the inverter was reduced. Output capacity was reduced in the low input voltage range. Outflow of DC component was prevented in high accuracy by usually correcting the zero point drift of detector, and by using the current detector with excellent linearity. To detect the DC ground fault, and to trip the output side breaker locating at the ground fault current pass, a zero phase converter detection circuit has been developed, by which the DC component can be detected at the DC input side. As a result of performance verification, the efficiency, power factor, EMI level, protection of outflow of DC component, protection of ground fault, protection of single operation detection, and noise level were satisfied. This system is prospective for the diffusion of photovoltaic power generation in the future. 3 refs., 8 figs., 1 tab.

Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

Characteristics and utilization of non-wood pulp and paper; Himokuzai pulp / kami no tokucho to sono riyo

Energy Technology Data Exchange (ETDEWEB)

Hara, H. [Mishima Paper Co. Ltd., Shizuoka (Japan)

1998-09-01

The reasons, difficulty in the usage, and the methods of use of non-wood papers are discussed. Non-wood papers sold in Japan are arranged basing on published data. The type of non-wood paper classified as special printing paper makes up the majority, and there are a variety of other products such as printing board, coated paper, thin paper, wrapping paper, functional paper, and watercolor paper. Kenaf and cotton are used in large quantities as non-wood plants for paper production, and use of bagasse and bamboo is increasing. Non-wood paper are used in consideration of environmental and resources problems and for utilizing the special features of non-wood fiber, and the characteristics of non-wood pulp and the effect of non-wood paper are discussed in this report. It is expected that papers utilizing the characteristics of non-wood paper will be developed. Non-wood papers are substitutions for various papers produced from wood pulp, and the fundamental point is the method of improving the original quality and paper quality by combining with non-wood pulp. 11 refs., 4 figs., 3 tabs.

Manufacture of lightweight aggregates utilizing coal fly ash. Sekitan bai riyo ni yoru jinko keiryo kotsuzai seizo

Energy Technology Data Exchange (ETDEWEB)

Ishii, K [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

1990-11-20

Processing of a large amount of coal ash is a serious problem in considering the locational conditions of coal firing power generation plants. 46% of the coal ash was effectively used in 1985, and the remaining 54% was disposed at landfills on land and sea. Positive promotion of the effective use of coal ash is the necessity. A production method for an artificial lightweight aggregate utilizing coal ash was established by a joint research. The history of the research and development of this artificial lightweight aggregate (brand name: FA-lIGHT), outline of the manufacturing facilities, physical properties and result of use are introduced. The lightweight aggregates are used not only for the construction of multistoried buildings but also used as most suitable aggregates for making lightweight large scale panels and concrete secondary products such as lightweight blocks. FA-LIGHT is most suitable for use in the production of concrete lightweight aggregates, and can be used for hydroponic agriculture and for the improvement of drainage of land. Spread of its use is expected. 5 figs., 5 tabs.

Technology of CCS coal utilization (outline of large-size demonstration test for CCS); CCS tan riyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

Konno, K [Center for Coal Utilization, Japan, Tokyo (Japan); Hironaka, H [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

1996-09-01

The coal cartridge system (CCS) is a series of the total system, in which coal is processed centrally at a supply base for each unit of consumer areas, supplied as pulverized coal in bulk units, and coal ash after combustion is recovered and treated. The system is expected of advantages resulted from the centralized production, elimination of handling troubles, and cleanliness. Following a small scale demonstration test, a large demonstration test for practically usable scale has begun in 1990, and completed in fiscal 1995. This paper introduces the CCS and reports the result of the test. In the large demonstration test, a supply station (with manufacturing capability of 200,000 tons a year) was installed in the Aichi refinery of Idemitsu Kosan Co., Ltd., and systematization on quality design and system technologies has been carried out. Long-term continuous operation for five years was achieved (operation time of the supply facilities was about 19,000 hours) without a failure and accident, to which every elemental technology was evaluated highly, and convenience and reliability of the system was verified. 13 figs., 3 tabs.

Practical use technology of coal ash (Poz-O-Tec); Sekitanbai no yuko riyo gijutsu (POZ-O-TEC)

Energy Technology Data Exchange (ETDEWEB)

Konno, K [Center for Coal Utilization, Japan, Tokyo (Japan); Saito, Y [Mitsui Mining Co. Ltd., Tokyo (Japan); Nagaya, Y [Mitsui Construction Co. Ltd., Tokyo (Japan)

1996-09-01

In order to utilize more effectively coal ash whose generation amount is increasing year after year, studies have been made on a technology to manufacture and utilize a high-strength substance solidified under normal temperature by utilizing hydration reaction of pozzolan system (Poz-O-Tec). The study works have been done as a subsidy operation of the Agency of Natural Resources and Energy, and were completed in fiscal 1995. Poz-O-Tec is a wet powder made of coal ash and stack gas desulfurization sludge (gypsum) added and mixed with lime and an adequate amount of water, which solidifies by hydration as pozzolan does. The same method as used for ordinary sands may be used as the basic application method. Because this is the material whose strength increases after construction, thickness of construction may be reduced smaller than in constructions using soils and sands. Test constructions of about sixty cases have been carried out to date, typically represented in use as a road bed material, banking, and a base material for water-barrier gutters. High-strength solid material which is stable under normal temperature may be obtained by adjusting calcium content. As a result of its effectiveness in practical use having been verified, a certificate of technological judgment has been issued for the material by the Civil Engineering Research Center. 3 refs., 11 figs., 2 tabs.

Synthesis and application of silica gel modified with alkoxyalcohols. Alkoxyalcohol shushoku silica gel no gosei to riyo

Energy Technology Data Exchange (ETDEWEB)

Moriguchi, T.; Ishiguro, H.; Matsubara, Y.; Yoshihara, M.; Maeshima, T.; Ito, S. (Kinki University, Osaka (Japan). Faculty of Science and Engineering)

1991-08-20

Several kinds of silica gel modified by alkoxyalcohols were synthesized by refluxing and dehyration and the organic reactions were studied when these silica gels were used as the catalyst. It could be confirmed by FT-IR spectra, DTA and elementary analysis that alkoxylalcohols adhere to the surface of silica gels without any decomposition. The acetate was produced by using alkyl halides. It was found that the modified silica gels had clearly the catalytic action for the reaction with n-hexyl bromide and dibromoethane although unmodified silica gels did not show the catalytic action. The reducing reaction of carbonyl compounds was carried out. The reaction proceeded at 25 centigrade for acetophenone, cyclohexanone, 1-indanone and 2-octanone to produce the corresponding reduction products. 11 refs., 5 figs., 4 tabs.

Research study on analysis/use technologies of genome information; Genome joho kaidoku riyo gijutsu no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For wide use of genome information in the industrial field, the required R and D was surveyed from the standpoints of biology and information science. To clarify the present state and issues of the international research on genome analysis, the genome map as well as sequence and function information are first surveyed. The current analysis/use technologies of genome information are analyzed, and the following are summarized: prediction and identification of gene regions in genome sequences, techniques for searching and selecting useful genes, and techniques for predicting the expression of gene functions and the gene-product structure and functions. It is recommended that R and D and data collection/interpretation necessary to clarify inter-gene interactions and information networks should be promoted by integrating Japanese advanced know-how and technologies. As examples of the impact of the research results on industry and society, the present state and future expected effect are summarized for medicines, diagnosis/analysis instruments, chemicals, foods, agriculture, fishery, animal husbandry, electronics, environment and information. 278 refs., 42 figs., 5 tabs.

Fiscal 1997 survey report. Feasibility study of the environmentally friendly type coal utilization system (survey of the coal utilization in Pakistan); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Pakistan ni okeru sekitan riyo gaikyo chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper made a literature survey, hearing survey, site survey/study on the coal in Pakistan such as the coal utilization system and the environmental situation, etc., and aimed at pre-examination for the survey of the introduction of the environmentally friendly type coal utilization system to be planned in Pakistan in the future. The examination, data collection and preparation were conducted in terms of the following items: the structure of coal consumption in energy supply, structure of coal consumption, mainly of domestic brown coal consumption, the situation of coal utilization by industry and by region, environmental problems caused by coal utilization such as air pollution, the trend of policies of environmental regulation, etc. The literature on the following was obtained and surveyed: the situation of economy/energy in Pakistan, coal utilization technology by industrial field, and environmental protection technology. The hearing survey was made to institutions concerned, corporation groups and men of learning and experience. Site surveys were conducted for the typically selected coal utilization equipment and existing environmental protection equipment. 66 figs., 56 tabs.

Study on utilization of shallow sea areas by developing the alga field. Test for utilization of coal ash on alga reef (interim report); Sojo zosei ni yoru asakaiiki riyo no kenkyu. Sekitanbai kokabutsu no sosho riyo shiken (chukan hokoku)

Energy Technology Data Exchange (ETDEWEB)

Tsuno, M.; Oikawa, M. [Hokkaido Electric Power Co. Inc., Sapporo (Japan); Matsubara, T. [Hokkaido Area Management and Support Foundation, Sapporo (Japan)

1996-03-25

A development was intended of an alga reef block that is suitable for adherence of algae and difficult of shore-burning by utilizing coal ash. Concretes with different coal ash displacement rates were used to install alga reef blocks embedded with natural rocks, steel plates, and the used desulfurizing agents on three areas (the Usubetsu area, the Tamagawa offing, and Chatsu Bay) including shore-burned sea areas along the coast of Tomari Village. Investigations were made on the states of adherence of useful algae as a result of difference in materials and locations of installation. The best adherence of edible kelp was observed at the Usubetsu area, followed by the Tamagawa offing and Chatsu Bay in that order. Growth conditions of the kelp by locations were conceived of the correlation with how extensively the natural kelp colonies are formed around each location, and how many nutrient salts are present and sea urchins are grown. No remarkable difference was observed in the adherence of algae due to the difference in the coal ash displacement rates. Porous blocks, however, showed less adherence amount. Kelp adherence condition was found good in the order of concrete, natural rocks, and the used desulfurizing agents. No kelps have adhered on the steel plates. 10 refs., 13 figs., 3 tabs.

Present status of and subjects on the industrial utilization of polymer separation membranes. Japan`s first largest sea water desalination plant by RO; Kobunshi bunrimaku no sangyo riyo no genjo to kadai. Zosui bun`ya ni okeru maku riyo

Energy Technology Data Exchange (ETDEWEB)

Furuichi, M. [Kurita Water Industries Ltd., Tokyo (Japan)

1998-07-05

The utilization in Japan and abroad is discussed of desalination methods using evaporation, reverse osmosis (RO) membranes, and electrodialysis membranes, out of various desalination techniques for seawater and others containing more salt. A new seawater desalination plant built in Okinawa, Japan, is outlined, and the future trend of Japan`s efforts for desalination is predicted. The said plant in Okinawa is the largest ever built in this country, and occupies 4th or 5th place in terms of capacity among similar facilities across the world. It was completed in April, 1997, and produces pure water at a rate of 40,000m{sup 3}/day. This plant, operating on RO, comprises eight RO membrane units each capable of 5131{sup 3}/day. The membranes are of the spiral type, consisting of Toray`s crosslinked aramid-base composite membranes and Nitto Denko`s membranes composed totally of crosslinked aromatic polyamide. The greatest of the pending tasks is to reduce the desalination cost. As for the operating cost of the desalination facility at the current stage, it costs 120-130 yen/m{sup 3} on the 40,000m{sup 3}/day scale, and the power cost occupies approximately 60% of the total operating cost. It is concluded that the consumption of electric power and chemicals per pure water produced have to be reduced. 8 refs., 5 figs., 5 tabs.

Fiscal 1996 result reports of the researches under consignment from NEDO. Developments of fuel cell technology, polymer electrolyte fuel cell, fuel cell power generation system technology, and high-voltage type several tens kW class distributed power source system; Shin energy sangyo gijutsu sogo kaihatsu kiko itaku gyomu 1996 nendo seika hokokusho. Nenryo denchi gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, koden`atsugata suju kW kyu bunsan dengen system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This paper precisely reports the research result on development of fuel cell technology in fiscal 1996. On verification of cell durability, the cell test result in hydrogen including CO of 100ppm using Pt-Ru catalyst as CO resistant catalyst showed that the loss percent of cell voltage decreases with an increase in Ru content. On development of stack technology, the carbon humidification plate superior in chemical stability was developed as one of the parts for layered stacks. The separator with a water- permeable carbon plate and serpentine flow fields was fabricated for highly layered stacks, and achieved the target performance in single cell power generation test. On establishment of design basis for compact fuel processor, the bench-scale test was conducted of Ru/{gamma}-Al2O3 and Pt-Ru/{gamma}-Al2O3 catalysts as advanced CO selective oxidation catalyst for CO reducers. On demonstration test for the several tens kW class stationary power plant, the system configuration of power generation plants using natural gas as fuel was studied. 106 figs., 38 tabs.

Fiscal 2000 achievement report. Research and development of fast-acting innovative energy-environment technology (Development of fast-acting high-efficiency solar cell technology - Development of high-quality ingot manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko itaku kenkyu gyomu seika hokokusho. Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu (Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu - Kohinshitsu ingot seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted of a technology for manufacturing an ultrathin polycrystalline silicon solar cell capable of efficiency enhancement and cost reduction earlier than the types of polycrystalline solar cells now available on the market. In this fiscal year, a silicon melt/solidification experimenting apparatus was built for manufacturing high-quality silicon ingots. Using an apparatus with its performance similar to the newly built one, a preliminary experiment was conducted involving high-purity silicon ingot manufacturing. In the experiment, boron was added to 75 kg of silicon for semiconductor devices so that its resistivity may be 0.5 ohm-cm. The silicon was melted in a quartz mold, and then subjected to unidirectional coagulation at 0.13 mm/min that started at the bottom to proceed upward. The result was a silicon ingot 44 cm times 44 cm times 17 cm (height). The ingot thus obtained exhibited 0.4-0.8 ohm-cm in resistivity distribution. Solar cells produced from the ingot showed a conversion rate of 16.9%. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional new technology creation R and D. First year report. R and D of medicine toxicity assessment use hepatocyte chip; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium kenkyu kaihatsu / chiiki shingijutsu soshutsu kenkyu kaihatsu. Dokubutsu dokusei hyokayo kansaibo chip no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Judging that in the beginning of the toxicity test, the necessary information/knowledge are acquired not by using animal itself but only by using liver system (hepatocyte), the development was proceeded with of the hepatocyte chip substituting for the animal experiment. Studies were made in the following five fields: 1) design of functional matrices; 2) development of the pharmacological assessment technology; 3) development of cell sensing technology/biosensor fabrication; 4) study of a possibility and the limit of cell patterning technology; 5) survey of the market scale. In 1), studies were made of the establishment of the 3D culture method for hepatocyte and the construction of hepatocyte models for medicine assessment using pieces of liver. In the latter, by including capsule using the sugar introduced with galactose residue which is special sugar of hepatocyte to alginic acid and chitosan which are natural polymer and also hepatocyte isolated into sponge, aggregate was formed, and its use as a medicine assessment use liver model was tried to be made. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). The R and D aims at establishment of observation/manipulation technology of atoms and molecules as common basic technology in various industrial fields such as new material, electronics, bio-technology and chemistry. The R and D thus aims at establishment of observation/manipulation of solid surfaces and DNA organic molecules, formation of fine structures of atomic surface arrangement, and calculation/ simulation for predicting a reaction theorem of atom and molecule surfaces. In fiscal 1997, research was made on improvement and development of computer simulation environment, and description of an excited state of electrons by Green function. Establishment of a construction method and computation code is under investigation for pseudo- potential dependent on excitation energy. Survey was made on research trends of the atom technology by visiting overseas academic societies and institutions. International Symposium on Atom Technology was also held in Tokyo in Nov. 1997

FY 1998 result report on development of superconductive power application technologies. Pt. 1. Research and development of superconductive wire materials / Research of a total system / Research and development of a freezing system / Demonstration tests; 1998 nendo chodendo denryoku oyo gijutsu kaihatsu. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Superconductive technologies are introduced into electric power devices for attempts of achieving higher stabilization, density and efficiency, as well as size and weight reduction and improvement in performance of the devices. The project has been worked on since fiscal 1998 as part of the New Sunshine Project. Fiscal 1998 being the eleventh year has taken the following subjects as the research promotion policies: establishment of plans targeted at accomplishment of the goals of the project; adequate and reliable implementation of verification of technological assignments; and steady and efficient demonstration tests. Subsequent to the previous year during which site demonstration tests were completed on a low-speed responsive model machine, the site demonstration test has begun on the ultra high-speed responsive model machine as the final stage of the project. The ultra high-speed responsive model machine was coupled with a freezing system and a load synchronizing machine, and different kinds of test were carried out where good results were obtained. Researches were conducted on characteristics improvement and device element technologies aimed at achieving the practical application level by utilizing the respective features of AC metal-based wires and oxide-based wires, where sound results were obtained. Also in an improved freezing system, valuable data were attained as part of establishing the basic technologies for a superconductive power generation system. (NEDO)

Project subsidized by the Sunshine Project in fiscal 1982. Report on achievements in the project commissioned from NEDO - development of a hot water utilizing power generation plant and development of a binary cycle power generation plant (Researches on corrosion preventive measures and the cycle optimum for the plant); 1982 nendo nessui riyo hatsuden plant no kaihatsu seika hokokusho. Binary cycle hatsuden plant no kaihatsu (fushoku taisaku no kenkyu oyobi plant saiteki cycle no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

As the element research on a 10-MW class geothermal binary cycle power plant to be built in the coming term, researches were made on corrosion preventive measures and the cycle optimum for the plant. This paper reports the achievements in fiscal 1982. In the research on corrosion preventive measures, different kinds of materials were buried in three locations having different soil natures to study corrosion due to soil. The corrosion rate of heat conducting pipes using the heat media R114 was estimated as very small as 1/40 of the corrosion rate in geothermal waters. In the research on the cycle optimum for the plant, experimental research was performed on thermo-dynamic properties and thermal stability of the mixed media using R114 as the main component. As a result, the R114/R112 system was found to have higher pressure than R114, but the media circulation amount is less, and the output at the power transmission terminal increased by 5 to 10%. The system showed the most excellent heat cycle characteristics. In the research of building a power plant installed with two different power generation systems, a computer program was prepared that calculates heat balances all at once for the case of installing a geothermal binary cycle power plant in a geothermal steam power plant. (NEDO)

FY 2000 report on the results of the development of the program system CO2 fixation/effective utilization technology. Development of the technology to assess global warming gas recovery/emission control by restoring/preserving the tropical mangrove coastal ecosystem; 2000 nendo program hoshiki nisanka tanso koteika yuko riyo gijutsu kaihatsu seika hokokusho. Mangrove nado nettai engan seitaikei no shufuku hozen ni yoru chikyu ondanka gas kaishu hoshutsu yokusei hyoka gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of developing the technology to assess the CO2 storage amount using the tropical mangrove coastal ecosystem, survey was conducted in the mangrove tree area in Ishigaki island, Japan and in Trat province, Thailand, and a draft of the assessment method was worked out. As to the assessment of the CO2 existence amount by analysis of satellite pictures, the regression equation between the mangrove existence amount and Landsat satellite data was determined to study a method for assessment of the CO2 storage amount in the whole area for survey. Further, using the relational equation between NDVI and LAI, vegetation indices reflecting vegetation conditions, methods to estimate the CO2 absorption amount by photosynthesis of mangrove tree community, the CO2 emission amount by respiration and the net production amount. Concerning the technology to assess the terrestrial area photosynthesis CO2 absorption amount, methods were studied for direct measurement of the amount of photosynthesis/respiration of the leaf area of mangrove tree community and the respiration amount by area such as trunk, branch and root and for assessment of CO2 absorption amount. Besides, studies were made on a variety of items such as the CO2 absorption/emission amount by underwater photosynthesis/respiration and decomposition of organic substances, the seawater exchange amount, and the rate of decomposition of organic substances. (NEDO)

Report on the results of the FY 1998 hydrogen utilization international clean energy system technology (WE-NET). Subtask 5. Survey on the R and D of technologies for hydrogen transport and storage by hydrogen absorbing alloys (V. Development of the distributed transport/storage use hydrogen absorbing alloys); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 5. Suiso yuso chozo gijutsu no kaihatsu (V. bunsan yuso chozoyo suiso kyuzo gokin no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The paper described the FY 1998 results of the development of hydrogen distributed transport/storage use absorbing alloys in the WE-NET project. Study was made of improvement of hydrogen desorption characteristics by substituting Ca for part of Mg of Mg-Ni alloys and substituting Cr for part of Ni. It is necessary to shift the state of atomic bond by H atom and metal atom in alloys from the ionic bond to the metallic bond, and to change from the amorphous state to the BCC type crystal structure. It was found out that it was possible to do it by improving the composition and heat treatment. The addition of Cu to LaMg{sub 2} alloys shifts the bond with hydrogen to the bond with metal. Easy hydrogen desorption and large absorbing capacity can be expected. It was found out that LaMg{sub 2}Cu{sub 2} synthesized by the reaction sintering method has reversible hydrogen absorbing desorption characteristics. The absorbing amount is 2.4 wt%, the desorption amount 1.2 wt%, and the desorption temperature 190 degrees C. Those are still far from WE-NET targeted values, but a clue to the search was obtained. It was found out that by applying doping technology by Ti, etc. to NaAlH{sub 4}, characteristics can be expected of the desorption amount, 4.5 wt%, of the hydrogen desorption starting temperature from 100 degrees C to 200 degrees C. (NEDO)

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of bio-recycling technology for bio-wastes; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Seibutsukei haikibutsu no bio recycle gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are exerted to develop a closed brewing system for 'shochu (a Japanese distilled liquor)' and vinegar and a non-combustion type thermal recycling system based on the methane fermentation of farm animal's excretion and sludge. Activities are conducted in the three fields of (1) the development of a zero emission shochu and vinegar brewing process, (2) development of a non-combustion type thermal recycling method, and (3) a commercialization plan. Studied in field (1) are the brewing of 'shochu' by a new process (kaeshi-shikomi), preparation of vinegar out of the lees of 'shochu' brewing, evaluation of the physiological activity of vinegar and 'shochu' lees, cost efficiency evaluation of zero emission 'shochu' and vinegar brewing processes, and the like. In field (2), the methane fermentation conditions for garbage, sludge, and farm animals' excretion are studied, and a non-combustion type thermal recycling process and the like are evaluated for cost efficiency. In field (3), marketability is studied for vinegar made by fermentation, actualities of the recycling of bio-wastes and energy recovery therefrom are examined, and marketability is studied for regional distributed power generation. (NEDO)

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of bio-recycling technology for bio-wastes; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Seibutsukei haikibutsu no bio recycle gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are exerted to develop a closed brewing system for 'shochu (a Japanese distilled liquor)' and vinegar and a non-combustion type thermal recycling system based on the methane fermentation of farm animal's excretion and sludge. Activities are conducted in the three fields of (1) the development of a zero emission shochu and vinegar brewing process, (2) development of a non-combustion type thermal recycling method, and (3) a commercialization plan. Studied in field (1) are the brewing of 'shochu' by a new process (kaeshi-shikomi), preparation of vinegar out of the lees of 'shochu' brewing, evaluation of the physiological activity of vinegar and 'shochu' lees, cost efficiency evaluation of zero emission 'shochu' and vinegar brewing processes, and the like. In field (2), the methane fermentation conditions for garbage, sludge, and farm animals' excretion are studied, and a non-combustion type thermal recycling process and the like are evaluated for cost efficiency. In field (3), marketability is studied for vinegar made by fermentation, actualities of the recycling of bio-wastes and energy recovery therefrom are examined, and marketability is studied for regional distributed power generation. (NEDO)

Fiscal 1996 survey report on overseas technology concerning R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu kaigai gijutsu chosa hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

R and D was conducted on technologies for ultra high purity separation/processing, ultra fine particle crystal control, and high functional organic material synthesis and support. The results were classified into four categories and, on the basis of the results, the researchers paid a visit to and had a conference with related organizations overseas, for the purpose of exchanging opinions with European and American specialists and extracting evaluation and problems of the results. On laser CVD/organic thin film technology, eight institutions including University College London were visited by the researchers, with opinions exchanged on eight subjects such as studies on synthesis of high functional metallic thin film using the laser MOCVD method. On new materials/processing technology, seven institutions including MIT were visited, with opinions exchanged on the results of four researches such as preparation of Pb-based ferroelectric thin film using multi-ion-beam sputtering method. On micro-structure characterization technology, six institutions including MIT were visited, with opinions exchanged on the results of nine studies such as micro-structure characterization by transmission electron microscopy. On ion CVD/ion implantation technology, five institutions including The University of Salford were visited, with opinions exchanged on the results of seven researches such as creation and utilization of ultra-high vacuum. (NEDO)

Fiscal 1996 survey report on overseas technology concerning R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu kaigai gijutsu chosa hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

R and D was conducted on technologies for ultra high purity separation/processing, ultra fine particle crystal control, and high functional organic material synthesis and support. The results were classified into four categories and, on the basis of the results, the researchers paid a visit to and had a conference with related organizations overseas, for the purpose of exchanging opinions with European and American specialists and extracting evaluation and problems of the results. On laser CVD/organic thin film technology, eight institutions including University College London were visited by the researchers, with opinions exchanged on eight subjects such as studies on synthesis of high functional metallic thin film using the laser MOCVD method. On new materials/processing technology, seven institutions including MIT were visited, with opinions exchanged on the results of four researches such as preparation of Pb-based ferroelectric thin film using multi-ion-beam sputtering method. On micro-structure characterization technology, six institutions including MIT were visited, with opinions exchanged on the results of nine studies such as micro-structure characterization by transmission electron microscopy. On ion CVD/ion implantation technology, five institutions including The University of Salford were visited, with opinions exchanged on the results of seven researches such as creation and utilization of ultra-high vacuum. (NEDO)

Fiscal 1996 report on the R and D result of industrial science and technology. R and D synergy ceramics (R and D on synergy ceramics); 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (synergy ceramics no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper summarizes the general survey mainly conducted by FCRA (Fine Ceramics Research Association) in fiscal 1996, and the joint research results with some universities, from some R and D on synergy ceramics. Silicon nitride based ceramics expressed the same high thermal conductivity as metal by seed crystal addition, grain growth control and orientation control of sheet lamination. For its practical use, study was made on control factors of material, formation and sintering. Ca2Y2Si2O9 single crystal was prepared by float-zone method to determine its crystal structure. No volume change due to high-temperature phase transition as thermal expansion was found. In carbothermal reduction- nitridation of SiO2, addition of Si3N4 seed powder increased a reaction rate and formed uniform particles with an isotropic shape. An average particle size was dependent on the size and number of fine particles in seed powder. Addition of both Si3N4 and Fe compound could change a particle shape from a spherical grain to an elongated grain. A spherical Fe-Si metal grain was found on the tip of an elongated grain. 66 refs., 73 figs., 13 tabs.

Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (high-efficiency III-V tandem solar cells); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (III-V zoku kagobutsu handotai taiyo denchi no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on technological development of III-V compound semiconductor solar cells in fiscal 1994. (1) On development of epitaxial growth technology of lattice mismatching systems, the optimum structure of InGaAs strain intermediate layers was studied for reducing a dislocation density by lattice mismatching of GaAs layer grown on Si substrate and difference in thermal expansion coefficient. The effect of strain layer on dislocation reduction was found only at 250dyne/cm in strain energy. Growth of GaAs layers on the Si substrate treated by hydrofluoric acid at low temperature was attempted by MBE method. As a dislocation distribution was controlled by laying different atoms at hetero-interface, the dislocation density of growing layer surfaces decreased by concentration of dislocation at hetero-interface. (2) On development of high-efficiency tandem cell structure, tunnel junction characteristics, cell formation process and optimum design method of lattice matching tandem cells were studied, while thin film cell formation was basically studied for lattice mismatching tandem cells. 45 figs., 8 tabs.

Technological development for super-high efficiency solar cells. Technological development of solar-high efficiency singlecrystalline silicon solar cells (high quality singlecrystalline silicon substrates); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Chokokoritsu tankessho silicon taiyo denchi no gijutsu kaihatsu (kohinshitsu tankessho silicon kiban no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on technological development for high quality efficiency singlecrystalline silicon substrates in fiscal 1994. (1) On electromagnetic casting/once FZ bath method, a Si single crystal of 600mm long was successfully obtained by improvement of power source frequency and furnace parts. High carbon content resulted in no single crystal including solids. In undoped electromagnetic casting ingots, resistivities over 1500ohm-cm were obtained because of effective preventive measures from contaminants. (2) On electromagnetic melting CZ method, since vibration and temperature control of melt surface by magnetic shield was insufficient for stable pulling of single crystals, its practical use was hopeless. (3) On electron beam melting CZ method, a Si single crystal of 25mm in diameter was obtained by preventive measures from evaporation of Si and influence of deposits, and improved uniform deposition distribution in a furnace. The oscillation circuit constant of power source, and water-cooling copper crucible structure were also analyzed for the optimum design of electromagnetic melting furnaces. 3 figs., 1 tab.

Fiscal 1997 report of the R and D result of industrial science and technology. R and D on synergy ceramics (development of rational energy use technology); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For rational use of energy resources, the process technology which allows harmonization and multiplication of conflicting characteristics was developed for development of new ceramic system materials. This paper summarizes the result in fiscal 1997. On a structural reaction process among creation technologies of ultra-reliable structure, study was made on structure control and hot-working technology through atmosphere control in ceramics synthesis. On basic technology for analysis and evaluation, study was made on the effect of particle bridging on strengthening and toughening of ceramic materials. Study was also made on a toughness expression mechanism, FEM model analysis of particle bridging, and crack growth resistance of ceramics. On control of solid solution precipitation, new alumina ceramics with high strength, hardness and wear resistance was obtained by transgranularly precipitating nano-size particles from a fine-grain high-density matrix through an improved particle formation process. Its toughness was considerably improved by controlling grain shape and grain boundary structure. A precipitation mechanism was also discussed. 89 refs., 107 figs., 14 tabs.

Research and development of photovoltaic power system. Research on low temperature deposition of polycrystalline thin films; Taiyoko hatsuden system no kenkyu kaihatsu. Teion seimaku gijutsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sato, K [Tokyo Univ. of Agriculture and Technology, Tokyo (Japan). Faculty of Technology

1994-12-01

This paper reports the result obtained during fiscal 1994 on research on a technology of low temperature deposition of polycrystalline thin films for solar cells. This research used ITO coated glass substrates, on which CdS was accumulated to a thickness of about 100 nm by using the CBD process, and over this deposition a CuInSe2 film was formed at 300{degree}C by using the ion cluster beam (ICB) process. The manufactured solar cells with a glass/ITO/CdS/CuInSe2/Au structure had an efficiency of 2%. In manufacturing a CuGaSe2 thin film by using the ICB process, effects of acceleration voltage relative to cluster beams and ionization current were investigated. It was found that the film morphology, the result of analysis by using X-ray diffraction, and the electric conductivity are sensitive to the ionization current. From these findings, an optimum film forming condition was derived. A CuGaSe2 thin film was manufactured by using the ICB process over a Cds thin film deposited by using the CDB process. Both of the surface morphology and X-ray diffraction patterns of the film did not show a large change, indicating a possibility of manufacturing cells with a reverse structure. Effects of heat treatment on CuInSe2 monocrystals were evaluated by using ESR and FTIR. 6 figs., 1 tab.

Development of large scale wind energy conservation system. Development of large scale wind energy conversion system; Ogata furyoku hatsuden system no kaihatsu. Ogata furyoku hatsuden system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for development of large scale wind energy conversion system. The study on technological development of key components evaluates performance of, and confirms reliability and applicability of, hydraulic systems centered by those equipped with variable pitch mechanisms and electrohydraulic servo valves that control them. The study on blade conducts fatigue and crack-propagation tests, which show that the blades developed have high strength. The study on speed-increasing gear conducts load tests, confirming the effects of reducing vibration and noise by modification of the gear teeth. The study on NACELLE cover conducts vibration tests to confirm its vibration characteristics, and analyzes three-dimensional vibration by the finite element method. Some components for a 500kW commercial wind mill are fabricated, including rotor heads, variable pitch mechanisms, speed-increasing gears, YAW systems, and hydraulic control systems. The others fabricated include a remote supervisory control system for maintenance, system to integrate the wind mill into a power system, and electrical control devices in which site conditions, such as atmospheric temperature and lightening, are taken into consideration.

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on chemical use); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kagaku riyo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-04-15

The whole amount of hydrogen consumption for chemical industries all over the world is estimated to be 249.7 billion Nm{sup 3} in 1974, while 367.2 billion Nm{sup 3} in 1980 roughly under a bold assumption, based on 3 current big consumption fields of ammonia production, methanol production and petroleum refining, and some promising fields in the future such as reduced iron and synthetic protein. Consumption ratios for every field are probably 54.9% in ammonia production, 30% in petroleum refining, 9.5% in methanol production and 5.6% in others in 1974, and nearly similar in 1980. However, although there are various troubles, if a large amount of methanol is used as fuel in the future, and its production plan is promoted to satisfy the demand of methanol fuel, hydrogen consumption for methanol production will increase drastically. In the future, if the production process of hydrogen as secondary fuel is established, such hydrogen also will be used for various chemical industries naturally. Research was thus made on use of oxygen as byproduct inevitably. (NEDO)

Report on the results of the FY 1998 hydrogen utilization international clean energy system technology (WE-NET). Subtask 1. Survey/research for the comprehensive evaluation and developmental plan; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 1. Sogo hyoka to kaihatsu keikaku no tame no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The paper described the results of the FY 1998 WE-NET project survey. WE-NET is composed of various element technologies such as hydrogen production, hydrogen transportation, storage technology, low-temperature materials, hydrogen utilization, and hydrogen combustion turbine technology. Therefore, considering the effectiveness as a total system, it is extremely important to traversally evaluate the situation of the R and D of each technology and developmental achievements and to work out developmental plans with integration, considering the effectiveness as a total system. From viewpoints of making effective promotion of the project and attempting optimization as a total system, it is necessary to make organic/comprehensive connection and adjustment among individual subtasks all the time. In this survey/research, in the case of proceeding with the above-mentioned studies, a committee having knowledgeable persons and learned persons as members was established. There, an investigational study was conducted over the whole WE-NET structural technology, and at the same time the following were attempted: the constant/mobile comprehensive adjustment of the whole project, evaluation of the developmental results, and optimization of the developmental plans. The results obtained in 6 years of Period I were evaluated traversally and comprehensively, and how to proceed with the development in Period II was proposed, which showed the developmental continuity. (NEDO)

Achievement report for fiscal 1998 on World Energy Network (WE-NET). Subtask 5. Development of hydrogen transportation and storage technologies (development of liquid hydrogen storage facilities); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 5. Suiso yuso chozo gijutsu no kaiahtsu (ekitai suiso chozo setsubi no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

An insulation structure suitable for large tanks was tested for insulation capability and strength at the liquid hydrogen temperature for the development of liquid hydrogen storage facilities. For the insulation test, a specimen was built of a porous solid material, and the specimen was given an additional duty of serving a test of a high temperature plate that was to impose loads on the specimen. The test conditions were not met, however, with too much variation in presence in temperature distribution. For the structural material compressive strength test, a method was worked out involving a hard urethane foam material specimen in liquid hydrogen, and was implemented. It was found that the specimen fracture that occurred was in the form of the collapse of the loaded surface. Tests were conducted at three temperatures, which were the normal temperature, the liquid nitrogen temperature, and the liquid hydrogen temperature, and compressive strength was determined for each of the three cases. No great difference in strength resulted from the difference between the two low temperatures. As for compressive strength at low temperatures, it was found that the strength was approximately two times greater than at the normal temperature. The above findings indicate that hard polyurethane foam is on the safe side when it is designed for the normal temperature. (NEDO)

Achievement report for fiscal 1998 on development of wide-area energy utilization network system. Study of energy system designing technology (Research into factory area energy system); Koiki energy riyo network system kaihatsu, energy system sekkei gijutsu no kenkyu 1998 nendo seika hokokusho. Kojogun no energy system ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

Actualities of exhaust heat and demand for heat in the area are investigated on the result of which a wide-area energy utilization network system will be built. In fiscal 1998, further questionnaires are distributed in addition to last fiscal year's, and door-to-door visits are made on leading factories representing 10 types of industries. The result of data analysis places the nationwide total of exhaust heat at 320,000 Tcal/year including heat generated by electric power generation. When it is so defined that usable heat be above 150 degrees C for exhaust gas, above 40 degrees C for hot water, and above 200 degrees for solids, the total will be reduced to 230,000 Tcal/year. Cleaning plants (plants that treat refuse or sewage) as the sources of exhaust heat besides the factories are investigated for the amount of heat they discharge, and then it is found that the amount of heat they discharge is the fourth largest following electric power plants, iron and steel mills, and chemical plants. It is also found that most of their exhaust heat is of good quality because it is latent in steam or hot water. It is acknowledged, partly because many of such plants are situated relatively near to the urban district, that their role is important when studies are made on the utilization of exhaust heat. (NEDO)

Development of high reliability dual redundant FADEC. Koshinraisei nijukei FADEC no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Endo, M [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

1994-05-01

The control unit of gas turbine for the aircraft jet engine use must draw overall performance in compliance with the thrust commanded by the pilot under all flying conditions of the engine. High reliability is required in flight safety. The present paper explains a developed unit of dual redundant FADEC (full authority digital electronic control) and high-density mounting technology for the electronic devices required by the FADEC. The FADEC unit is composed of two hardware systems with their respective microprocessors of the same structure. Each of both systems can solely control the engine, while they are both commanded by a necessary signal for the dual system operation and connected through a digital by-pass which can exchange the input/output data between them. For the operational confirmation of FADEC unit, its control characteristics were inspected by intentionally putting it out of order at the time of engine acceleration/deceleration and other transient operations. The control system could be switched without control characteristics lost of the engine. 9 figs., 2 tabs.

Development of a new automotive navigation system; Shingata navigation system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sone, M; Nakano, H; Nakayama, O; Tanemura, E; Yoshitsugu, N; Watanabe, M [Nissan Motor Co. Ltd., Tokyo (Japan)

1996-01-31

An automotive navigation system was outlined. Features of this system are described below: map display called `Bird View` extending up to the horizon was commercialized; accuracy of determining the vehicle`s present position was realized using new algorithm; and automatic route selection was adopted. Human machine interface of this system also was completely reviewed. `Bird View` was realized by reading plane map data out from CD-ROM and converting them onto the coordinate on the virtual screen in front of the view point. Automatic selection which depends mostly on self-contained navigation adopts the certain way in comparison of the computation position in GPS. To assume vehicle advancing direction, employed were optical fiber gyroscope, geomagnetic sensor, and Karman filter making a good use of advantages of GPS, for the improvement of accuracy. For the automatic distance correction, a function of correcting pulse-distance conversion coefficient was employed, and the free maintenance was realized. 5 figs.

Hydrogen battery car developed in Matsuda; Matsuda suiso nenryo denchisha wo kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-01

Matsuda announced that the hydrogen battery car 'Demio FCEV' was developed by the company. This new type car not only does not need an air humidifying machine, but also supplies the necessary electricity with an ultra capacitor of a large scale condenser. Its maximum output is 40 kw, the highest speed is 90 km per hour, and the accelerating time from the stop state to 40 m is about 5 seconds, the same level as a gasoline car. One time of hydrogen charging serves for 170 km running. As a hydrogen battery car, it is the third one in the world, following the DAIMURA in Germany and TOYOTA. (translated by NEDO)

Development of solar power generator system; Taiyoko netsufukugo hatsuden system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kisara, K; Kumagai, T; Niino, M; Chen, L; Eguchi, K [National Aerospace Laboratory, Tokyo (Japan)

1997-11-25

Described herein is a new hybrid solar power generator system, in which solar energy is separated into the light and heat components by a wavelength-selective filter before being directly converted into electric power, the former for the amorphous solar cell (ASC) unit and the latter for the thermoelectric unit. These units complement with each other to enhance overall efficiency. The ASC unit should have a higher efficiency when it works on the light component, because the heat (infrared) component increases cell temperature and decreases its output. For the ASC unit, the effects of the filter have been tested. The thermoelectric unit, generating power by the Seebeck effect, should have a higher efficiency, if heat flux passing through the unit can be increased, because of increased temperature differential, to which voltage produced increases proportionally. For the thermoelectric unit, heat is collected by a parabolic mirror unit from sunbeams received by a heliostat. Characteristics of these units are grasped almost as expected by the tests. 4 refs., 11 figs., 1 tab.

How to proceed R and D effectively; Gijutsu kaihatsu no koritsutekina susumekata

Energy Technology Data Exchange (ETDEWEB)

Kawakita, Tetsuya [Ajinomoto Corp., Tokyo (Japan)

1999-07-05

They greatly divide R and D into next three in the enterprise, it is considered. (1) The goal-oriented basic research. (2) The applied research. (3) Technology development. Here, they try to want to consider the measure for efficient result sending out in technology development. It always considers that the largest effect is raised in research personnel who was limited in advancing technology development, it is observed in the standpoint for the operation management. The thought of Concurrent Engineering has already been taken in daily management, and it is had thing sure. In large wave of the internationalization, the high competition superiority is ensured in respect of the cost competitiveness, while the goal is clarified, and while it lectures on the means for overcoming the bottleneck. Responding to the expectation of the management by the further improvement in the technology development force believes not differing role of the engineer in the enterprise. (NEDO)

Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A phenomenon of excess heat generation through the electrolysis of heavy water using palladium metals as electrode can be recognized as new hydrogen energy. Its mechanism has been investigated for four years since FY 1993. In FY 1993, the New Hydrogen Energy Demonstration Research Center and the New Hydrogen Energy Demonstration Laboratory were organized, and the research was initiated. For the excess heat generation demonstration model tests, two types of electrolysis experimental units were constructed, and the Pd/D-based electrolysis experiments were initiated. For the measurements of excess heat using an open type electrolysis cell, there were rather large errors ranging from -13% to +7%. It is necessary to improve the accuracy. For the measurements using a fuel cell type electrolysis cell, generation of the excess heat ranging from 0% to 6% was observed. For the validity of this, it is required to confirm the long-term stability of calibration and cell components. For the correlation between the increase in absorbing rate and the generation of excess heat, results of 2 to 3% lower were obtained. 28 refs., 89 figs., 26 tabs.

Development of advanced coal cleaning process; Kodo sekitan kaishitsu gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Osaka, S [Center for Coal Utilization, Japan, Tokyo (Japan); Akimoto, A; Yamashita, T [Idemitsu Kosan Co. Ltd., Tokyo (Japan)

1996-09-01

This paper aims to develop a clean coal production process which excellently removes environmental pollutant, is low-costed, and need no particular systems for distribution of products. The result of the development was described paying attention to column flotation which is a technology to high-efficiently select particulate regions, particulate heavy media cyclone, magnetic separation, and the basic design of the process into which those above were integrated. The two-stage selection process, which is an integration of column flotation and particulate heavy media cyclone into the conventional coal preparation equipment, can produce low-ash clean coal at high separation efficiency and also suppress the rise in processing cost. This process was also effective for removal of sulfur content and trace metal elements. The use of clean coal at power plant can be effective for not only the reduction in ash treatment amount, but the aspect of boiler operation characteristics such as heat transfer efficiency of boiler furnace wall, ash related troubles, loads of electrostatic precipitator, loads of flue gas desulfurization facilities. 17 figs., 5 tabs.

Development of lane change aid system; Lane change aid system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Uemura, H; Yoshida, T; Butsuen, T [Mazda Motor Corp., Hiroshima (Japan); Sakai, N; Nakano, T; Nakamoto, T

1997-10-01

We have developed a lane change aid system, which detects vehicles behind in adjacent lanes with CCD images, shows the driver the information of vehicle location with a head-up display, and warns him/her if necessary. By comparing the brightness on two CCD images, distance distribution along several CCD lines is measured. To assure the effective vehicle detection on public roads, we have developed a detection algorithm which distinguishes vehicles and guard-rails by observing the patterns of measured distances. We will show the system configuration, detection logic, and the system evaluation on public road. 5 refs., 12 figs.

Development of catalyst for diesel engine; Diesel engine yo shokubai no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Ueno, H; Furutani, T; Nagami, T [Toyota Motor Corp., Aichi (Japan); Aono, N; Goshima, H; Kasahara, K [Cataler Industrial Co. Ltd., Shizuoka (Japan)

1997-10-01

The new concept catalyst for diesel engine has been developed. When the exhaust temperature is low, SOF and HC are temporarily adsorbed by the adsorbent within the catalyst and are oxidized as the temperature rise. The process of this development have manifested as follows. (1) The coating material is important factor to govern the oxidation activity. (2) SOF is reduced by the coating material in low temperature less than 200degC. (3) The coating material, which has low SO2 adsorbing rate suppress the sulfate formation at high temperature. 2 refs., 11 figs., 1 tab.

Development of ultra-low pressure reverse osmosis membranes; Choteiatsu gyakushintomaku no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Hirose, M.; Ito, H.; Ohara, T. [Nitto Denko Corp., Osaka (Japan)

1998-06-05

Described herein is development of ultra-low pressure reverse osmosis (RO) membranes. The composite RO membrane, which is now widely used, has a cross-sectional structure consisting of an ultrafilter membrane as the support and a very thin skin layer responsible for filtration. It is confirmed that the skin layer is of a pleated structure. Growing this structure can greatly accelerate permeation of water without damaging arresting and durability characteristics of the membrane, and hence is a desired approach. Utilization of molecular structure simulation of the skin layer materials is investigated by the molecular dynamics. The results show that the stable structure of the material for the skin layer in the RO membrane is a network structure with regularly arranged honeycombs, when it should arrest at least 99% of salt. These techniques serve as the bases for development of the ultra-low pressure RO membranes (ES Series), where the skin layer is made of cross-linked, totally aromatic polyamide. The membrane passes twice as large a quantity of water as the conventional one, is highly resistant to chemicals, and arrests 99.7% of salt. 3 refs., 4 figs.

Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This report describes results of the study on the excess heat generation phenomenon during the electrolysis of heavy water using palladium metals as electrode in FY 1995. For the measurements of excess heat using an open type electrolysis cell during the excess heat generation demonstration model tests, significant excess heat beyond the range of input was not measured both for ICARUS-1 and for ICARUS-2. For the measurements using a fuel cell, high absorbing rate more than 0.85 was stably achieved for highly pure Pd electrode material by heat treatment and surface treatment. The excess heat could be reproduced for plural tests. The heat recovery rate more than 98% was obtained using the NHE type flow calorimetric system. The excess heat measurements using this are examined. For the reactive palladium materials, various materials ranging from single crystal to cold working polycrystal materials were systematically used for the absorbing experiments. Benchmark tests were also conducted through the cooperation with related researchers. 18 refs., 135 figs., 28 tabs.

NEDO Forum 2000. Industrial technology development session; Sangyo gijutsu kenkyu kaihatsu session

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

This session presented the following subjects: I. IT innovation, II. Bio-seminar, III. Nano-technology, IV. Machine technology seminar, and V. 'Development subsidy project to put industrial technologies into practical use'. The theme in I relates to (1) influence of IT innovation on the society, (2) the theory of semiconductor evolution, (3) the theory of liquid crystal evolution, and (4) the theory of disk evolution. The theme II searches (1) how far have bio-technologies come?, (2) search of human evolution from genes, (3) can human being live up to 150 years by bio-technologies?, and (4) what is a DNA array (chip)?. The theme III covers (1) product innovation in polymers (new polymeric materials brought about by polymer nano-technology, taking polyolefin as an example), and (2) creation of ceramics materials by using nano-technologies. The theme IV relates to (1) ITS changes the car society into this way, (2) the current status and outlook on research and development of micro-machine technologies, and (3) the futuristic society and new industries opened by the Humanoid project. The theme V describes (1) practical application of ultra-small medical device production technologies, (2) development of next generation semiconductor manufacturing resists, (3) development for practical application of an optical brain function imaging device, and (4) development for practical application of new screening technologies toward creation of medicines using genome. (NEDO)

Fiscal 1974 research report. General research on hydrogen energy subsystems; 1974 nendo suiso riyo subsystem sogoteki kento hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1975-03-01

Based on the contract research 'General research on hydrogen energy subsystems and their peripheral technologies' with Agency of Industrial Science and Technology, each of 7 organizations including Denki Kagaku Kyokai (Electrochemical Association) promoted the research on hydrogen energy subsystem, combustion, fuel cell, car engine, aircraft engine, gas turbine and chemical energy, respectively. This report summarizes the research result on the former of 2 committees on hydrogen energy and peripheral technologies promoted by Denki Kagaku Kyokai. The first part describes the merit, demerit, domestic and overseas R and D states, technical problems, and future research issue for every use form of hydrogen. This part also outlines the short-, medium- and long-term prospects for use of hydrogen and oxygen energy, and describes the whole future research issue. The second part summarizes the content of each committee report. Although on details the original reports of each committee should be lead, this report is useful for obtaining the outline of utilization of hydrogen energy. (NEDO)

Test results on vegetable cultivation using fish breeding water; Yogyosui riyo ni yoru yasai saibai shikenkekka ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Nishida, S. [Hokuriku Electric Power Co. Inc., Toyama (Japan)

1997-10-30

Although a part of the entrails of fishes, birds and livestock is used for food, most of them are treated by costly combustion because of their bad odor and looking, and International Environment and Welfare Laboratory, Toyama prefecture in Japan is studying their profitable treatment. As a part of such study, possibility of hydroponic cultivation of vegetable was tested using fish breeding water including excretions of fishes and residual feeds after use of waste as feed, and the growth condition, safety and effectiveness of cultured vegetable were verified. Three-hundred and fifty viviparous Oryzias were released into a breeding water area with no controlled pH and EC (electric conductivity). For comparison a culture solution area of 6.0 in pH and 1.2ms/cm in EC was prepared. The result on cultivation of 6 kinds of vegetable in culture beds supported by circulation of these water showed that hydroponic cultivation of vegetable using fish breeding water is possible, and average growth of 68% is obtained although difference in growth for every vegetable is found. 8 figs., 5 tabs.

Fiscal 1997 report on technological results. R and D on micromachine technology (Development of micro-factory technology); 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Activities are conducted in search of a micromachine system in which devices and equipment relating to machining, assembly, transportation, inspection, etc., in use for a manufacturing process are integrated in a narrow space, for the purpose of conserving energy through the miniaturization of the process of manufacturing small industrial products. With the activities in the two fields of (1) R and D of systematization technology (experimental system for micro fabrication/assembly) and (2) comprehensive investigation and research, examination on detailed specification for the experimental system was carried out, as were the examination of element technologies, element device operating experiments, technological investigation, etc.. In (1), sophistication of the element technologies was contrived that were required for realizing each experimental system, while the detailed specification of each experimental system was decided. Further, a part of the element devices was experimentally manufactured, with the basic functions verified. In (2), research studies were compiled on radio interference for example in the case where various devices were integrated and highly densified through the formation of a micro-factory; also compiled was a joint research with Agency of Industrial Science and Technology, a research conducted for the purpose of building the conception of the micro-factory. (NEDO)

Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of microfactory technology; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The goal is to save energy and minimize the working space by constructing a manufacturing system comprising various micromachines with their dimensions fit for parts and products they handle. Development continues relative to microprocessing (electrolysis, and optical processing) and microscopic liquid operation (micropump, and part holding device). Under research in relation to the assembly process are a micro-arm to handle tiny parts and precision techniques for interfitting within a very small microfactory, a piezoelectric actuator for microscopic position adjusting, and ultraprecise microprocessing techniques indispensable for their manufacture. Also under research are the incorporation of optically driven microdevices developed before the preceding fiscal year into a microfactory and the study of microservo actuators capable of sophisticated positioning and velocity control. Concerning the microscopic transport system to deal with microscopic parts and products, studies are under way so as to embody systems driven by actuators of the electromagnetic type and electrostatic type. In this paper, reference is made to inspection techniques and comprehensive investigations. (NEDO)

FY 1999 report on the results of the R and D of high efficiency clean energy vehicles; 2000 nendo choteisonshitsu denryoku soshi gijutsu kaihatsu seika hokokusho. Kiban gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Using the petroleum substituting clean energy, the R and D were conducted with the aim of developing vehicles which reduce the consumption of travel energy to 1/2 and the CO2 emission to 1/2 or below of those of existing vehicles. The FY 1999 results were summed up. As to the R and D of the hybrid power system, carried out were the prediction of fuel consumption performance by numerical simulation, evaluation of performance of new hybrid electric vehicles, etc. Concerning the R and D of high efficiency clean energy vehicles, the R and D of the following were reported from each of the makers: hybrid passenger car loaded with methanol fuel cells, hybrid passenger car loaded with ANG engine, hybrid truck loaded with CNG ceramic engine, hybrid truck loaded with CNG engine, hybrid bus loaded with LNG engine, and hybrid bus loaded with DME engine. Further, in the survey of synthetic fuels, the paper reported on the results of the evaluation of synthetic light oil engines and evaluation of characteristics of synthetic light oil. (NEDO)

Fiscal 1997 report under consignment from NEDO on the R and D of femto-second technology (development of ultra short pulse optoelectronics technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku femto gyo technology no kenkyu kaihatsu (chotan pulse ko electronics gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Very high speed electronics technology is indispensable for the creation of industrial base technology which supports high grade informatizing in the 21st century. The state of light and electronics is controlled in the femto-second time domain. As to the development of femto-second light pulse generation/transmission technology, mode synchronous semiconductor laser was manufactured using the strain quantum well structure aiming at heightening profit, and the repeated frequency, 166GHz, was achieved. Relating to the pulse compression element, exciton photonic band was newly designed. A technology of coding was also studied. As to the development of technology of femto-second light pulse control/distribution, shortening of the wavelength down to 1.5{mu}m and a possibility of femto-second domain high speed response were indicated by the combined double quantum well structure. The quantitative measurement of spin relaxation characteristics was successfully made. By the Mach-Zehnder light switch, obtained was the world`s fastest light switching characteristic. To realize the femto-second class very high speed element, conditions were grasped on the crystal growth of Sb based ultra thin films operating in the 1.5{mu}m zone by studying the quantum well using transition among sub-bands. 242 refs., 280 figs., 12 tabs.

Fiscal 1997 basic research on coal resource development (equipment development). Report on R and D of new exploration technology (exploration of medium-depth coal deposits in water areas); 1997 nendo sekitan shigen kaihatsu kiso chosa (kiki kaihatsu hen) hokokusho. Shintansa gijutsu chosa kaihatsu (suiiki chushindoso tansa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes the research result on development of new coal exploration technology. For a high-precision and high-resolution reflective seismic exploration system, R and D was made on the exploration technology of several meter in resolution for medium-depth (800m) coal deposits under a lake of 2m deep. As a result, the high-frequency and high-power source (150-200Hz in dominant frequency, 700-800m in penetrability) and the high-frequency and high sensitivity receiver (10-1000Hz in frequency band, 35V/PA in sensitivity) were developed successfully, and the positioning system was improved. The final evaluation of these elementary technologies was carried out through demonstration tests, resulting in satisfactory results. For a high-efficiency trial drilling system, the in-bore trouble prevention system for measurement, processing and analysis of drilling data (drilling length, drilling rate, revolution, bit load, torque) and drilling mud data (charge water pressure, charge/discharge water, density, pH, viscosity) was constructed. The outlook for low-cost measurement and a safety during drilling was thus obtained. (NEDO)

Fiscal 1998 research report. Industrial science and technology research project / R and D on creative advanced functional materials (structure-controlled materials) / Harmonized molecular materials; 1998 nendo dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) seika hokokusho. Bunshi kyocho zairyo no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

R and D on harmonized molecular materials aim at establishment of the technology fabricating self-assembled organic molecular films on solid surfaces which have potentials of mechanical response to electric fields, electroluminescence or optical functions. Molecule harmonization expresses new structures and functions difficult to be expressed by each molecule alone, by cooperative interaction between molecules due to noncovalent bond. Functional thin films were developed by controlling alignment and/or arrangement of molecules with an aid of self-assembling processes. Thiol compounds with larger dielectric anisotropy were synthesized as electric field responsive self-assembled films. {pi}-conjugated compounds composed of phenyl-capped oligothiophenes were synthesized as electroluminescent self-assembled films, and their high crystallinity and efficient electroluminescence were found. Heat- and solvent-resistant lyotropic liquid crystalline (LLC) aligning polymers such as polyamine and polyimine were synthesized as new optically functional LLC dye self-assembled films. (NEDO)

Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell / low-cost and large-area module / next-generation thin-film solar cell (Manufacture of thin-film polycrystalline solar module); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Fiscal 1997 is the first year of another 4-year-long research and development phase. In addition to researches for improving on thin-film polycrystalline Si cell efficiency that have been under way, new efforts are started, which include the development of practicality-conscious thin film producing technologies aiming at higher throughput and yield and the development of modularization process technologies which are necessary for putting thin-film cells to practical use. Concerning the formation of a power generation layer on a polycrystalline Si thin film formed by the ZMR (zone-melting recrystallization) process, studies are conducted for improvement on its throughput and yield using a new CVD (chemical vapor deposition) unit. A method of modularization is evaluated, which involves a laminate of a thin-film cell attached to a resin-coated, reinforced glass substrate and an EVA (ethylene vinyl acetate) back film. A remarkable achievement is earned toward the practicalization of technologies of thin film formation enhanced in quality and throughput and technologies of thin film modularization. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment form NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of molecular harmonized materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) bunshi kyocho zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

By establishing microtechnology using molecular-level bottoming-up (molecular harmonization) by imitating the system of living organism, the paper described the R and D of molecular harmonized materials aiming at developing high-functional/high-performance materials such as high-performance catalyst, photo-information functional materials and sensing materials. Under consignment from NEDO, Japan Chemical innovation Institute started the 5-year plan in fiscal 1997. Self-assembled molecular films, in which organic molecules are orderly arranged by self-assembly, aim at developing new memory/optical/sensing materials. Mesophase materials which are such materials as liquid crystal showing the intermediate state between solid and liquid, develop optical/photoconductive materials using precise molecular orientation controllability. Macroporous materials are such substances as zeolite having molecular size micro pores. The paper aims at establishment of synthesis techniques of them and development of high-performance catalyst, etc. using them. In the comprehensive investigational research, conducted was a survey of the trend overseas in addition to a study of subjects in question. Further, the supporting basic study was reconsigned to universities, etc. 57 refs., 62 figs., 17 tabs.

FY 2000 report on the results of the development of commercialization technology of the photovoltaic power system. Summary. R and D of the photovoltaic power generation utilization system/periphery technology (R and D on the improvement of reliability of photovoltaic power generation - Investigative study of long-term reliability of inverter - Separate volume: Data on the life evaluation test); 2000 nendo New sunshine keikaku seika hokokusho(Sokatsu ban). Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (Taiyokohatsuden no shinraisei kojo ni kansuru kenkyu kaihatsu - Inbata no choki shinraisei no chosa kenkyu - Bessatsu : Jumyo hyoka shiken datashu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of establishing a life evaluation method for power conditioner of about several kilowatts for general housing use, the acceleration test was made, and the data were summarized for maintenance of power quality, cooperation with the protection system at power system, insuring of safety of personnel/facilities, etc. As to the acceleration method, by paying attention to heat deterioration of thermal plasticity materials being used for power conditioner and by using the acceleration method using the 10-degree C half law by the Arrhenius law, temperature and humidity were set at 40 degrees C and 36%, respectively. The operation hour and stopping time were fixed at 3.5 hours and 4.5 hours, respectively. The life evaluation measurement by the acceleration test was composed of the continuous evaluation measurement with the aim of early finding the degradation of performance, anomaly, etc. of power conditioner and of the evaluation measurement at specified intervals with the aim of precisely measuring the state of degradation of power conditioner. As a result of the continuous evaluation measurement, the paper reported the data on the rise in temperature inside the power conditioner during the acceleration test and the change in electric characteristics of input/output. (NEDO)

Industrial and scientific technology research and development project in fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Research and development of superconducting materials and transistors (report on overall investigation of superconductive devices); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (chodendo soshika gijutsu kaihatsu seika hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes development of superconducting new function transistors. Fiscal 1997 as the final year of the project advanced improvement in such transistor-using processes as formation and micro-processing of superconducting thin films to show enhancement in characteristics of high-temperature superconducting transistors and possibility of their application utilizing their high speed motions. Furthermore, fundamental technologies were studied with an aim on junction transistors to be applied as circuits. For field effect transistors, evaluation was performed on critical current distribution of step-type particle boundary junction to make it possible to evaluate characteristics of hundreds of transistors. At the same time, a magnetic flux quantum parametron gate with three-layer structure was fabricated to identify its operation. In superconducting-base transistors, strong reflection was recognized on temperature dependence of permittivity of an Nb-doped strontium titanate substrate used for collectors, by which barrier height was reduced. In the junction transistor and circuit technology, isotropic ramp-edge junctions were fabricated, and so was a frequency divider circuit with single magnetic flux quantum mode operation for evaluating high-speed response characteristics. High time resolution current was observed successfully by using a high-temperature superconducting sampler system. 148 refs., 127 figs., 4 tabs.

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 4. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (Shiryo 4). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elements, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include instrumentation-related drawings covering an instrumentation loop sketch, instrument inspection specifications (flow meter, level gage, pressure gage, thermometer, regulation meter, analyzing meter, signal receiving meter, and instrument board), general specifications for electrical instrumentation facilities, etc. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 5. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 5). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elementary matters, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include engineering specifications related to electrical designs, lists of electrical items, specifications related to civil engineering designs, drawings such as planning drawings, and a detailed construction design drawn by an Australian engineering corporation and related documents and drawings. Concerning the manufacture of mechanical systems, items procurable in Japan, specifications of items procurable in Australia, lists, drawings, etc., are shown. Also included are the details of on-site preparation for construction and on-site work, conceptual designs of processes of dehydration, deashing, and secondary hydrogenation, etc. (NEDO)

Fiscal 1998 survey report. Medical equipment (Development of fine sampling/analysis system for blood / Development of high-precision 3-D image diagnosis system / Development of low-invasion operation support system / Total development of artificial internal organ technologies); 1998 nendo chosa hokokusho. Iryo kiki (ketsuekinado biryo saishu, biryo bunseki system kaihatsu/koseido sanjigen eizo shindan system kaihatsu/teishinshu shujutsu shien system kaihatsu/jinko zoki gijutsu sogo kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For efficient medical care supply systems, the R and D of advanced medical care technology and equipment largely contribute to productivity improvement for medical care services. Among them, a progress of medical care technology is becoming important for preparation of efficient and fair supply systems. MITI thus established 'Medical care and welfare equipment development project' in 1994, and has promoted the strategic long-term R and D project of medical care and welfare equipment as joint R and D project of NEDO and private enterprises. In fiscal 1998, on the development of the fine sampling/analysis system for blood, the high- precision 3-D image diagnosis system, the low-invasion operation support system, and the artificial internal organ technologies since fiscal 1996, this project clarified essential technical issues based on the future view, selected some themes to be newly developed in the future, and surveyed and evaluated the details of their R and D concretely. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of silicon-based polymeric materials (development of liquid methane fueled aircraft engine); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo / Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Keisokei kobunshi zairyo no kenkyu kaihatsu (methane nenryo kokukiyo engine kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This R and D aims at establishing the basic technology on the molecular design, synthesis, use as materials, and evaluation of silicon-based polymers, of which excellent electronic/optical functions, high heat-resistance/combustion-resistance/dynamic characteristic are expected. The paper introduced the results of the fiscal 1997 R and D of them. The themes are as follows: technology of synthesis of silicon-based polymeric materials with sea-island microstructures, interstitial type structure forming technology, composite materials with organometallic complexes and silicon-based polymers, silicon-based polymer structural materials with ring structures, optimization of the Wurtz`s synthesis method of silicon-based polymers, unsaturated and hypercoordinate organosilicic compounds, function of silicon-based polymers, synthesis and polymerization of new silicon-based monomers, development of a new synthesis method of polysilane and the function, development of new application of silicon-based polymers in imaging devices for recording/memory/display of information, molecular design of {pi}-conjugate and {sigma}-conjugate compounds including silicon, and conformation and electronic state of silicon-based polymeric materials. 186 refs., 141 figs., 68 tabs.

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 5. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 5). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elementary matters, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include engineering specifications related to electrical designs, lists of electrical items, specifications related to civil engineering designs, drawings such as planning drawings, and a detailed construction design drawn by an Australian engineering corporation and related documents and drawings. Concerning the manufacture of mechanical systems, items procurable in Japan, specifications of items procurable in Australia, lists, drawings, etc., are shown. Also included are the details of on-site preparation for construction and on-site work, conceptual designs of processes of dehydration, deashing, and secondary hydrogenation, etc. (NEDO)

Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell and of low-cost/large-area module (Formation of low-temperature film); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usukau taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (teion maku keisei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A polycrystalline Si thin film formation technology is developed, which uses the flux process in which a reaction occurs between the target crystal and a flux component which is eutectic. Using this process, a crystal grain relatively large in diameter is obtained at a relatively low temperature. This method is now attracting attention as one of the technologies for producing crystalline Si film for use in thin-film polycrystalline Si solar cells. Especially when Al is used for flux, since Al is automatically doped into the target crystalline Si film, it is expected that the resulting film will serve as the ground for a photoactive layer provided with the BSF (back surface field) function which is important for the improvement of solar cell efficiency. A polycrystalline Si thin film is formed on a 2cm times 2cm-large glass substrate at a temperature not higher than 600 degrees C. It is recognized that films selectively oriented towards the (111) or (100) plane are acquired when other processes are employed. It is expected that the said Al-doped film provides a ground on which a BSF function-provided photoactive layer will be formed. (NEDO)

Achievement report for fiscal 1996 on the research and development of superconductor technology to power generation. Pt. 1. Research and development of superconducting wire, generator, total system, and refrigeration system; and verification test; 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

In the research and development of superconducting wires, studies are conducted to increase the current capacity of NbTi and Nb{sub 3}Sn metal wires and to improve their properties, and to increase the current capacity of oxide materials and improve their performance making full use of the features of each manufacturing method. In the development of superconducting generators, a slow excitation response type is tested for verification, and a good result is attained; and a quick excitation response type is tested for field winding static excitation, and good performance is exhibited. Using the results so far achieved, the 200,000kW class pilot machine concept design is reviewed. In the study of total systems, feasibility is studied of a quench test for the 70,000kW class machine through simulation analyses, etc. In the development of refrigeration systems, efforts are exerted to improve on the conventional type in terms of reliability and to further improve on the improved version in terms of performance and space-saving feature. One of the endeavors involves the development of a He Brayton cycle turbine driven compressor. A multilayer cylindrical rotor is verified in terms of functions, characteristics, reliability and durability, and various data are collected toward the development of a pilot machine. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the superconducting material and device (technical development of the Josephson device hybrid system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (Josephson soshi hybrid system no gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In order to establish basic technology for hybrid systems of superconducting and semiconducting devices, study was made on ultrahigh speed and low energy consumption properties of Josephson devices. As Josephson IC technology, a logical circuit, ring network, memory circuit, and oxide superconductor logical circuit were studied. As superconducting hybrid system technology, a Josephson device- semiconductor device interface, formation technology of signal transmission lines, and Josephson-MOS IC technology were developed. In fiscal 1997, as Josephson IC technology, switch motion of 4GHz in clock frequency was achieved by new high-density wiring process. Integration of some semiconducting processor elements, junction of surface- stabilized superconducting thin films, and motion of combination structure of some SQUIDs were also confirmed. On the hybrid system, voltage conversion operation of all interfaces was confirmed. Proper logical operation of the Josephson device hybrid circuit was also confirmed. 95 refs., 90 figs., 5 tabs.

Achievement report for fiscal 1981 on Sunshine Program-assisted project. Data 4. Development of coal liquefaction technology/Development of solvent extraction liquefaction technology/Development of brown coal solvent extraction plant (Development of 50t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (Shiryo 4). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Research is conducted for the development of a liquefaction plant (50t/d pilot plant) for Australia's Victorian brown coal. In fiscal 1981, using the process concept and design data obtained through the study of elements, a detailed design of a primary hydrogenation system is drawn, part of the equipment is procured, and on-site construction work is started. The book is a collection of materials which include instrumentation-related drawings covering an instrumentation loop sketch, instrument inspection specifications (flow meter, level gage, pressure gage, thermometer, regulation meter, analyzing meter, signal receiving meter, and instrument board), general specifications for electrical instrumentation facilities, etc. (NEDO)

Report on the results of the FY 1998 hydrogen utilization international clean energy system technology (WE-NET). Subtask 7. Survey/study on hydrogen utilization technology; 1998 nendo suiso riyo kokusai clean energy system (WE-NET). 7. Suiso riyo gijutsu ni kansuru chosa kento

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The paper described the results of survey/study of the FY 1998 WE-NET project. In Subtask 7, survey/study have been made on the main hydrogen utilization technologies except the hydrogen combustion gas turbine since FY 1993. Based on the survey results having been obtained, study was made on conditions for introducing promising technology, future prospects, etc. in FY 1998. As to the power generation, the basic combustion test and test on hydrogen injection equipment as element test, and test on ignition equipment were carried out using rapid compression/expansion equipment. A scenario for introducing hydrogen vehicle was made, and at the same time environmental LCA was conducted by which environmental influences can be assessed. The survey of the market of pure hydrogen polymer electrolyte fuel cells were made in terms of the electric utility use, industrial use, residential/commercial use, and movement/vehicle use. Study was conducted on the combined process of oxygen production equipment and He Brayton cycle in the subzero fractionation/low-temperature VSA method. Various methods including performance, price, etc. were surveyed/studied, making it a precondition that hydrogen supply stations are installed in stand-alone distribution near places of consumption. (NEDO)

Investigations in fiscal 2000 on feasibility of environment friendly coal utilization system. Feasibility survey on environment friendly coal utilization system in India; 2000 nendo kankyo chowagata sekitan riyo system kanosei chosa hokokusho. Indo ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Taking the area of the clean coal technology (CCT) effective for energy conservation and environment preservation as the object, a feasibility survey has been performed on executing a model project in India. About 70% of the total power generation capacity in India depends upon coals existing in abundance inside the country. Since the local coals are high in ash, low in sulfur, and low in calorie, the environmental problem related to thermal power plants is the disposition of fly ash. The Central Electricity Authority of India expects solving this problem by CCT introduction. It also expects increase in combustion efficiency by using ultra-critical boilers. The Indian cement industry often uses in-house electric power generation facilities because of high electric power cost, wherein the produced coal ash is used as a cement raw material. The matter of the strongest interest is the introduction of a high-efficiency combustion system that depends on low-grade coals. Among the CCTs, strong interest was shown in the fluidized bed cement kiln and the circulating fluidized bed boiler. The iron and steel industry has expectations toward effective coal washing technologies and coke manufacturing technologies. (NEDO)

Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in Thailand; Kankyo chowagata sekitan riyo system kanosei chosa. Tai ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper investigated and studied the present situation and future trend of coal utilization and distribution in Thailand, and the present situation of environmental effects and the measures taken for environmental protection. Around 2010, coal will probably be produced only at EGAT`s Mae Moh (MM) coal mine. Demand for overseas coal is expected to be 40-50 million tons in 2011, and preparation of the coal center becomes a subject. For general industry use coal, pretreatment such as coal preparation, coal blending and briquetting is needed, considering coal quality, usage, transport distance and environmental effects. Brown coal of MM coal mine is a lignite with high sulfur, high ash content and low heating value. Wide spread of its use can be expected if upgrading is possible such as desulfurization, deashing, increasing heating value. In the electric power generation field, the absorber was installed at the existing boiler of the mine-mouth generating plant to conduct a verification test on high grade desulfurization of ultra-high sulfur lignite. In the industry field, the circulating fluidized bed boiler was adopted. In the residential/commercial field, introduction of briquette was proposed. 80 refs., 84 tabs.

Ultimate evaluation report on research and development of basic technologies for next-generation industry. Conductive polymeric materials; Jisedai sangyo kiban gijutsu kenkyu kaihatsu saishu kenkyu kaihatsu hyoka. Dodensei kobunshi zairyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-05-01

Basic technologies are established that equip polymeric materials (insulators in general) with conductivity similar to that of metals for the realization of novel conducting materials characterized by light weight, high resistance to corrosion, and ease of machining, and for the manufacture of novel electrical/electronic materials having new functions different from those of conventionally used metals. The aims are to realize a conductivity of 10{sup 5}S/cm or more, to manufacture materials sufficiently stable when left in the ordinary or inert atmosphere, and to manufacture materials which may be machined into proper shapes as required in the industry. The results of the 10-year-long development endeavor greatly contribute to the creation of high-level materials, the systematization of technologies, and the elucidation of the conducting mechanism. In relation to polymeric materials, in particular, a new technology is developed that equips, with high reproducibility, polymeric materials with conductivity similar to that of silver or copper; a graphitic material is created for the first time provided with conductivity superior to that of metals; and conducting polymeric materials are equipped with an easy-to-machine feature. A great contribution is accomplished to the production of superconductivity in organic charge-transfer complex crystals and to the elucidation of the conducting mechanism. (NEDO)

Fiscal 1998 R and D report on femtosecond technology (ultra-short pulse optoelectronics technology); 1998 nendo femuto byo technology no kenkyu kaihatsu (chotan pulse hikari electronics gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report reports the result of the fiscal 1998 R and D on femtosecond technology supported by NEDO. For creation of industrial basic technologies supporting the advanced information society in the 21st century, ultra-high speed electronics technology including new functions beyond the speed limit of conventional electronics technologies is indispensable. From such viewpoint, this R and D aims at establishment of the basic technology necessary for ultra- high speed electronics technology through R and D of technology controlling conditions of beams and electrons in a femtosecond (10{sup -15}-10{sup -12} seconds) region. In fiscal 1998, this project first succeeded in fabrication of a prototype pulse compressor by using semiconductors, and developed a new pulse compressing method by using fibers to generate ultra-short pulse of 38fs. By developing new materials for intersubband transition where ultra-high speed responses can be expected, optical absorption by intersubband transition was first confirmed at optical communication wavelength. The main result for every theme is reported and explained. (NEDO)

Sunshine Program for fiscal 1981. Development of practical application technologies for photovoltaic power systems (Management of research and development); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

To gain a helpful guide toward the next process by properly evaluating the current project, evaluation of cost and inputted energy is indispensable. In fiscal 1981, as the first step of such evaluation effort, a manufacturing process model is built based on data about designing and manufacturing, and is subjected to analysis. Cost forming factors are extracted from the respective processes, and their relations are analyzed. Parameters are analyzed for the survey of energy that a system demands for operation. Test facilities now under construction are also subjected to a cost analysis. A system design document is prepared for cost analysis and for assisting the process improvement and evaluation work. For the establishment of low-cost mass-production technologies, it is necessary to reappraise the currently-employed technologies for all the processes. It is necessary to coordinate the basic processes in terms of dimension and efficiency to enable them to function as a continuous, consistent production process. Target values are set for the respective processes for an output of 500kW/year at a cell conversion efficiency of 9%. In selecting items to be specified and values to be attained, users' requests are fully considered. Details are prudently coordinated of conditions for delivery from a process to another. (NEDO)

Surveys for promoting development of overseas coals in fiscal 1999. Surveys on international coal situation; 1999 nendo kaigaitan kaihatsu kodoka nado chosa (kaigaitan kaihatsu sokushin chosa). Kokusai sekitan jijo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Detailed surveys were performed on Britain, Germany and Spain being the major coal producing countries in Europe with regard to a general view on the status of energy demand and supply, the status of demand and supply of coal, business institutions, and related policies in each country. The status of demand and supply of coal, and related policies in the three countries may be summarized as follows: In Britain, the ratio of coal accounted for in the primary energy supply is 18.0% in 1998, and the coal production amounted to 35.5 mill.TCE/year; closure of underground mining coal mines is discussed recently; the congress is deliberating re-introduction of the subsidy system which had been once discontinued; in Germany, the ratio of coals accounted for in the primary energy supply in 1997 was 14% in bituminous coal and 11% in brown coal; the quantities of production of bituminous coal and brown coal in 1998 were 41.8 and 50.6 mill.TCE/year, respectively; the number of mines has decreased because of the unification; the subsidy policy is in continuation; in Spain, the ratio of coal accounted for in the primary energy supply was 13.5% in 1997 and the quantity of coal production in 1998 was 12.5 mill.TCE/year; unification of coal operators has not been advanced as far as in Germany; and the subsidy is provided as in Germany. (NEDO)

Sunshine Program for fiscal 1981. Development of practical application technologies for photovoltaic power systems (Management of research and development); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

To gain a helpful guide toward the next process by properly evaluating the current project, evaluation of cost and inputted energy is indispensable. In fiscal 1981, as the first step of such evaluation effort, a manufacturing process model is built based on data about designing and manufacturing, and is subjected to analysis. Cost forming factors are extracted from the respective processes, and their relations are analyzed. Parameters are analyzed for the survey of energy that a system demands for operation. Test facilities now under construction are also subjected to a cost analysis. A system design document is prepared for cost analysis and for assisting the process improvement and evaluation work. For the establishment of low-cost mass-production technologies, it is necessary to reappraise the currently-employed technologies for all the processes. It is necessary to coordinate the basic processes in terms of dimension and efficiency to enable them to function as a continuous, consistent production process. Target values are set for the respective processes for an output of 500kW/year at a cell conversion efficiency of 9%. In selecting items to be specified and values to be attained, users' requests are fully considered. Details are prudently coordinated of conditions for delivery from a process to another. (NEDO)

Research and development of peripheral technology for photovoltaic power systems. Research on engineering methods for cost effective PV installation; Shuhen gijutsu no kenkyu kaihatsu. Tashu secchi koho no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of engineering methods for photovoltaic power system installation in fiscal 1994. (1) On the survey on applicable fields, various application aspects, applicability, and problems on location and legal regulation were continuously studied for railway, river reservation, lake surface and public facility as promising locations after highway in the last fiscal year. The result pointed out relatively easy possibility of PV power generation of nearly 11,700MW except residence and building fields. (2) On installation technology of solar cell arrays, several models based on various installation conditions, construction methods and system configurations were studied, and various application aspects were proposed by combination of simple design conditions. (3) On test and evaluation of the structural design of array racks, wind tunnel experiments were conducted for structure wall, platform shed and highway sound insulation wall. (4) On basic design of various promising systems, the conceptual design of interconnection systems was carried out assuming applications to highway and railway. 7 figs., 3 tabs.

Development of active rear steer actuator. Development of four wheel steer actuator for active safety; Active rear steer actuator no kaihatsu. Yobo anzen ni muketa 4WS actuator no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Yamanaka, T [Aisin Seiki Co. Ltd., Aichi (Japan)

1997-10-01

Recently, ecology, energy saving and safety have become important issues. And Active Safety is spotlighted in vehicle control area. Many researches and developments on four wheel steer system have been done to improve vehicle stability. We have developed the Active Rear Steer system with electromechanical Actuator, which is mass-productive, compact, and high response and durable. 10 figs., 5 tabs.

FY 1999 survey report on the survey on the role and course of the development of technology such as CO2 recovery, fixation and effective use in the industrial policy; 1999 nendo CO{sub 2} kaishu koteika yuko riyo nado gijutsu kaihatsu no sangyo seisakujo no ichizuke oyobi hokosei ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper aims at arranging and assessing the role of themes of the technology development such as CO2 recovery, fixation and effective use in the industrial policy and the results of the development. It also aims at analyzing factors to hinder technology development in comparison with the developmental trend of technology and the role in the industrial policy in foreign countries and at considering the future role in the industrial policy and the course to be taken. Judging from the number of projects and a variety of fields of technology, it could be said that the development of the related technology in Japan is at a top level the same as that in the U.S. In the present conditions, however, most of the technologies are at the stage of the basic research. In many of the research fields except a part like EOR, it is difficult to promote the research only by economical principles, and the government as core needs to promote it. As viewed from an international point, the development/commercialization of technology such as CO2 recovery, fixation and effective use are extremely important from an aspect of not only the heightening of competitiveness in the domestic industry, but Japan's international contribution in the 21st century. (NEDO)

Research and development in second term of hydrogen utilizing international clean energy system technology (WE-NET) in fiscal 1999. Task 2. Hydrogen absorbing alloys for discrete hydrogen transportation and storage; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 11. Suiso bunsan yuso chozoyo suiso kyuzo gokin

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Developmental researches have been performed on hydrogen absorbing alloys intended to be applied to stationary and moving objects. This paper summarizes the achievements in fiscal 1999. As a method for evaluating effective hydrogen absorption amount, proposals were made on definition and measuring method for effective hydrogen absorption amount assuming hydrogen absorption at 20 degrees C, and 10 and 30 atmospheric pressures, and hydrogen discharge at 100 degrees C and one atmospheric pressure. In the research of an Mg-Ni based alloy, the Mg based alloy having the Laves composition, treated by mechanical grinding was found to discharge hydrogen of 0.2 to 0.35% by mass at 423K. This discharge temperature is the lowest among the Mg based alloys having been developed to date. In the research of the V based hydrogen absorbing alloy, the V-Ti-Cr-Mn alloy was developed successfully that discharges hydrogen of 2.64% by mass when hydrogen absorbed at 273 K and 3.3 MPa is discharged at 373 K and 0.01 MPa. Furthermore, development has been made on the V-Ti-Cr-Mn-Ni alloy that shows high effective hydrogen absorption amount without being treated by heat. This alloy has as high effective hydrogen absorption amount as 2.47% by mass under the above described conditions. (NEDO)

Survey report for fiscal 1998. Survey of the current state and tasks of research and development of technologies for effectively utilizing CO{sub 2} fixation by higher vegetation; 1998 nendo chosa hokokusho. Koto shokubutsu ni okeru nisanka tanso koteika yuko riyo gijutsu no kenkyu kaihatsu no genjo to kadai ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Investigations and studies are conducted seeking for a CO2 fixation method improved by utilizing the photosynthesizing function of higher vegetation. Details of higher vegetation genes are being disclosed thanks to the rapid progress of studies making use of molecular biological techniques, and the application of the genetic mechanism to scientific and technological fields is becoming increasingly feasible. In particular, the role of the CO2 fixation enzyme RuBisCO has been elucidated almost completely. It has been learned that, in terms of photosynthesizing capability, the C{sub 4} plants (corn etc.) are 2-3 times higher than the C{sub 3} plants (rice, wheat, etc.), and 5-10 times higher than the CAM plants (cactuses etc.). Studies are also under way about the rice genome so that a photosynthesizing capability so high as that of the C{sub 4} plants may be endowed the rice plant. The metabolism and control of useful substances produced in the CO2 fixation process etc. in the higher vegetation are being investigated, and it is now expected that some day such useful substances will be produced and utilized efficiently. Researches are under way into the relationship between the green leaf that is the organ that performs photosynthesis and the organ (sink) that stores and utilizes starch and sugar is in progress, and now a new field is going to open where vegetables will be fully utilized. (NEDO)

Report on the FY 1999 survey for making a data book related to new energy technology development. Trends of solar energy utilization, waste power generation, clean energy vehicle, geothermal power generation, clean coal technology, other new energy technology and new energy technology development; 1999 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa hokokusho. Taiyonetsu riyo, haikibutsu hatsuden, clean energy jidosha, chinetsu hatsuden, clean coal technology, sonota no shin energy gijutsu, shin energy gijutsu kaihatsu kanren doko

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The paper collected/arranged the most up-to-date data made public in the new energy technology field. As to the solar energy utilization, the utilization is on the decrease with the beginning of the 1980s as a peak, and the solar systems introduced in FY 1998 totaled 15,000 and the water heaters 56,000. The waste power generation is showing a steady growth both in the general use and in the industrial use, and the introduction of 5 million KW is expected for FY 2010. The sale of the hybrid car started at the end of 1997, and the subjects are the price/performance/fuel supply system. Concerning the geothermal power generation, 497,000 KW and 36,000 KW were introduced for business use and non-utility use, respectively. Japan ranks sixth among nations of the world. Relating to the coal liquefaction, the pilot plant (PP) of Japan's original bituminous coal liquefaction NEDOL process finished operation in 1998, and the construction of technology package, international cooperation, etc. are being conducted. About the coal gasification, the construction of demonstrative equipment and operation are planned during FY 2002 - FY 2007, making use of the PP achievements of IGCC. In regard to the biomass-based waste power generation, the lignocellulose system is large in potential quantity. As to the hydrogen energy, the WE-NET project entered Period II. With respect to the ocean thermal energy conversion, the demonstrative study started. In relation to the wave power generation, a small size of approximately several hundred W was commercialized. (NEDO)

Report on the results of research and development under a consignment from NEDO on deca-nano quantum integrating transistor substrate technologies; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Deca-nano ryoshi shusekika soshi kiban gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Researches have been conducted on deca-nano quantum integrating transistor substrate technologies, and developments were made on a three-dimensional device simulator which can be used in deca-nano domains, and a circuit simulator to have quantifying function transistors coexist with silicon semiconductor integrated circuits. The researches were intended to develop a simulator capable of analyzing properties of very small silicon and compound semiconductor devices in deca-nano domains. The researches discussed the applicability of conventional simulators, calculated quantum levels in a three-dimensional hetero structure, and resulted in development of an electron wave propagation simulator in optional two-dimensional shapes, a quantum Monte Carlo simulator, and a three-dimensional semiconductor device simulator with quantum correction. On the other hand, in order to estimate characteristics of a hybrid circuit in which single electron transistors coexist with conventional transistors such as CMOS transistors, a single electron hybrid circuit simulator was developed. The development indicated that a CMOS-SET fused memory is promising as a future LSI memory. 22 refs., 116 figs., 3 tabs.

Achievement report for fiscal 1981 Sunshine Program on development of practical application technologies for photovoltaic power systems. Development of photovoltaic demonstration systems (Research and development of systems for factories); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden demonstration system kaihatsu (kojoyo system no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

In the effort at constituting an optimum system, a 2kwp mini-system is completed after designing and introducing an array output measuring unit, DC control unit, dummy loads, etc. The system is actually operated for collecting various data, and commercial noise, transmission line safety, surplus power utilization, solar cell utilization rate, efficiency of various kinds, etc., are subjected to analysis. The basic designs of measuring instruments for a 100kwp full-scale system are also examined. In relation with the manufacture, testing, and arrangement of solar cell arrays, a large solar simulator is designed and introduced for the measurement of module photoelectric characteristics. Using this simulator, continuous irradiation is performed by a 1kW/m{sup 2} light beam of a spectral distribution of AM (air mass) 1.5. A CZ (Czochralski) single crystal, EFG (edge defined film bed growth method) ribbon, and a small CdS/CdTe solar cell module are installed, through the use of which operating characteristics are determined for comparative study. A DC control unit is designed and built, composed of a rectifying device for the dissolution of noise that greatly affects measurement for the mini-system, DC-AC-DC converter, and a remote control console. (NEDO)

Report on results of R and D of coal liquefaction technology under Sunshine Project in fiscal 1981 (development of motive force recovery system by hydrohoist); 1981 nendo sekitan ekika gijutsu no kenkyu kaihatsu, chokusetsu suiten ekika plant no kaihatsu seika hokokusho. Hydrohoist ni yoru doryoku kaishu system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This paper explains the results of development of a hydrohoist system in a direct hydro-liquefaction plant under the Sunshine Project in fiscal 1981. Coal liquefaction deals with three phases of gas, liquid and solid at high pressures of 100-300 kg/cm{sup 2}. Slurry consisting of coal, catalyst and solvent is once fed into a supply chamber by a low pressure slurry pump. A high pressure slurry formed in a liquefaction reactor, after the separation of gaseous object, is boosted by a booster pump and force-fitted into the supply chamber from the above, discharging the slurry in the chamber to the high pressure reactor side. Since the high pressure product is used as the driving liquid, a force-feeding motive force can be greatly curtailed. It is a motive force recovery type hydrohoist. The product slurry in the supply chamber is discharged from a valve in the upper part; with the inner pressure going down quickly, the discharge valve wears very little. The basic experimental equipment was manufactured in fiscal 1980, with a test research conducted using the improved main equipment in fiscal 1981, and with the conceptual design of the hydrohoist also implemented on the assumption that it was applied to a pilot plant. (NEDO)

Fiscal 1997 R and D project on industrial science technology under consignment from NEDO. Report on the R and D of nonlinear optoelectronic materials; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Hisenkei hikari denshi zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As to the development of organic base materials, the paper is going ahead with an evaluation, higher performance and further use as materials of basic optical properties of quirale nonlinear materials and organic conjugate base materials which are promising among organic low molecular materials. As the development of orientation control crystal growth technology, grooves for orientation control were formed on the surface of the lead glass substrate, from which thin film single crystals were obtained. The nonlinear response was studied of the glass where semiconducting fine particles dispersed in matrix glass. Glass scattering base prototype materials were selected by the sol-gel method and ultra-low melting-point glass method. The glass dispersion base materials by the very fast cooling method was also studied. For the purpose of realizing a high speed switching characteristic, a processing technology was developed of ultra fine particle dispersing polymer light waveguide. As to the technology for super lattice, the optimum nonlinear performance materials were selected mainly with the optimum complex super lattice base. Moreover, the three-dimensional super structuring technology was constructed to improve nonlinear optical characteristics. The comprehensive investigational study was conducted for effective promotion of the research development. 177 refs., 260 figs., 27 tabs.

Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (research and development of composite materials on solar cells under microgravity environment); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (bisho juryoku kankyo wo riyoshita taiyo denchiyo zairyo kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on development of composite materials for solar cells under microgravity environment in fiscal 1994. (1) On a thin film capillary method, 26 experiments of GaSb thin film crystal growth were conducted using the especially prepared high-accuracy electric furnace under microgravity. The wettability of thin film crystals was improved by refining equipment. Rhombus crystal planes and large crystal grains were observed in GaSb thin film crystals prepared under microgravity. (2) On a liquid phase method, the effect of the gravity on crystal structure and grain morphology was studied for synthesis of CdS fine grains. (3) On technological development of composite materials, the solidification experiment of Cu-In-Se melt was conducted under short time microgravity of 10{sup -4}g for 10 sec. As a result, more uniform texture and more high crystallinity were obtained under microgravity, and In in melt was concentrated by surface tension effect. It was suggested that high-quality CIS thin films will be obtained by Se doping into Cu-In composite films under microgravity environment.

Technological development for super-high efficiency solar cells. Technological development for super-high efficiency singlecrystalline silicon solar cells (super-high efficiency singlecrystalline Si solar cells); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Chokokoritsu tankessho silicon taiyo denchi no gijutsu kaihatsu (chokokoritsu tankessho silicon taiyo denchi cell no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on technological development of super-high efficiency singlecrystalline silicon solar cells in fiscal 1994. (1) On development of high-performance light receiving layer, the fine electrode for receiving surfaces was designed to reduce serial resistance, and the high-quality oxide passivation film was studied to reduce surface recombination velocity. (2) On development of forming technology of back heterojunction, the high-quality cell with B-doped fine crystalline Si film on its back was studied by heat treatment of the fine crystalline Si film, and the cell structure with high back reflectance of light was also studied. (3) On analysis for high-efficiency cells, the relation between the back recombination velocity at the interface between p-type substrate and back passivation film, and the internal collection efficiency as probe light was injected from the back, was calculated by numerical simulation. As a result, the cell back recombination velocity could be evaluated by measuring the spectral internal collection efficiency to back injection. 15 figs., 6 tabs.

Vat leaching of gold ores and utilization of the tailings; Kinkoseki no vat leaching to koshi no yuko riyo

Energy Technology Data Exchange (ETDEWEB)

Hosooka, T. [Nippon Clay Mining Co. Ltd., Tokyo (Japan); Miyagawa, H. [Mitsui Mining and Smelting Co. Ltd., Tokyo (Japan)

1996-01-25

Mitsui Kushikino Mine previously processed two gold ores from Kushikino and Iwato ore deposits by the all slime cyanidation method, where the ores were ground to fine size smaller than 75 {mu}m and leached with sodium, cyanide. A large amount of slimes were produced as waste and discarded in tailings ponds. To save the costs of grinding and waste treatment it is desirable to process coarse sized ores. The Iwato ore is gold and silver bearing silicified porous rock. As most gold and silver in the Iwato ore are concentrated in the pores, leaching of coarse sized ore is expected to be possible. Laboratory tests and pilot plant tests of vat leaching for the Iwato ore were carried out using 0.15-8.0 mm feed. These results showed that the gold dissolution rate was similar to that by the all slime cyanidation and the decrease in gold recovery was a few %. The properties of these tailings can be used in fine aggregate of concrete. Based on the results vat leaching of the Iwato ore was adopted in the plant. The tailings are sold and used as fine aggregate. Utilization of slime tailings from the other ores was also developed and they are used as flux in copper smelters. Now, there is no tailings pond at Mitsui Kushikino Mine. 9 refs., 10 figs., 5 tabs.

Technologies and techniques for analysis and use of genome information, 1997; Genome joho kaidoku riyo gijutsu no chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper clarified the whole image of cell functions by elucidating the function and manifestation control mechanism of genes existing in genomes, and the network of their interactions, and surveyed applicability of the useful functions obtained of cells and proteins to the industrial field. The survey was made from a viewpoint of the fields of both biology and information science. Especially, based on the function-known DNA base sequence database, the following technologies were surveyed: technology to predict the function of the function-unknown DNA base sequence, search/separation technology to acquire the genes to be functionally elucidated in a state of being suitable for manifestation, technology to get perfect proteins by effectively manifesting the genes to be functionally elucidated, and technology to analyze the function of the proteins obtained by manifestation of genes. Further, the International Symposium was held which is titled `Genome Research Opens a New World to Bioindustry (New Developments in Genome Informatics Technologies). With the future progress of technology to decipher and use genome information, the construction of much newer genome industry is anticipated. 165 refs., 44 figs., 10 tabs.

`Power storage system` dealing with leveling of electric power use; Denryoku riyo no heijunka ni kotaeru `denryoku chozo system`

Energy Technology Data Exchange (ETDEWEB)

Igarashi, M. [Meidensha Corp., Tokyo (Japan)

1996-06-28

An overview is given on the development situation of a Zn-Br battery as a power storage system. The system is aimed at storing excess power at night and supplying the on-load demand during daytime. The power storage technology requires a large output and capacity of MWh level, long term stability and durability, and cost as low as pumped storage power generation. Four kinds of batteries have been examined to cope with the conditions, in which development of Zn-Br batteries along with Na-S batteries is in progress towards practicability. As a power conversion method for this system, GTO has been employed for a large capacity unit and IGBT for a medium/small capacity unit. The reliability of the Zn-Br batteries against leakage was improved by laminating each cell by hot plate welding. The service life was improved by using a material with a high bromine resistance in place of the conventional electrode constituent material. Although the battery efficiency was influenced by each resistance of electrode, film and electrolytic solution, distance between electrodes, temperature, etc., these correlations were clarified so as to establish the simulation technology. At present, the system realizes 50kW and 40kWh/m{sup 3}. 1 ref., 8 figs.

Research trend survey on the stable isotope utilization technology; Antei doitai no riyo gijutsu ni kansuru kenkyu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report reviews the activities and the trends in the area of the stable isotope use attracting attention recently. In the medicine and clinical treatment sector, the remarkable trends are the extension of {sup 13}C use. The breath test and the magnetic resonance spectroscopy (MRS) diagnosis have been developed as inspection methods. It is noted that investigation has been initiated on the magnetic resonance imaging (MRI) using {sup 3}He and {sup 129}Xe for the lung imaging. In the organic chemistry and biochemistry sector, the stable isotopes are used for analyzing the structures of complicated natural compounds and materials relating to life science and for analyzing the chemical reaction mechanism of organic compounds. In the nuclear energy sector, {sup 10}B and {sup 7}Li have been used as neutron absorption materials and pH neutralizing reagent, respectively. In the analysis and measurement sector, the process of isotopic dilution is used for the environmental analysis of trace elements including harmful substances. Among various separation methods of isotopes, well studied uranium enrichment processes and deuterium separation processes are described. Separation of {sup 15}N by ion exchange resin method and plasma ion cyclotron resonance (ICR) isotope separation have been studied, recently. 133 refs., 53 figs., 7 tabs.

Quiet STOL research aircraft development program. Teisoon STOL jikkenki kitai kaihatsu sogo hokokusho

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

The airframe development program of the quiet STOL research aircraft (ASKA) promoted by National Aerospace Laboratory, Japan is reported in detail. ASKA was developed based on a C-1 medium-sized troop and freight transport aircraft for the Air Self-Defence Force, and four turbofan- jet engines were substituted for two previous engines. Its first flight was conducted successfully on Oct. 28, 1985 after 8 year development from 1977 to 1985. The ASKA was developed separately on its airframe, engine and flight, and this report includes every related matter to its airframe. The promotion system, budget and executive system are reported in the second chapter, and the design requirements, safety standard and basic design in the third chapter. Several related tests such as wind tunnel test and flight simulation test are reported in the 4th chapter, and the structure and equipment of ASKA are outlined in the final chapter. The appendix includes the line-up of and discussions in the technical committee, the list of newly developed functional parts, the list of design reports and the list of related tests. 50 refs., 8 figs., 23 tabs.

Development of an automatic emergency reporting system; Jiko jido tsuho system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kawai, A; Sekine, M; Kodama, R; Matsumura, K [Nissan Motor Co. Ltd., Tokyo (Japan)

1995-06-30

This paper proposes an automatic emergency reporting system as an ASV technology for preventing secondary damage. In the event a vehicle is involved in an accident or other emergency situation, this system automatically reports the vehicle`s present position along with information on the vehicle and owner to an operations center via radio signals. This makes it possible to dispatch an ambulance or other emergency vehicle more quickly. A prototype simulation system has been built consisting of a custom designed control unit for in-vehicle use and a personal computer that simulates an operations center. The interface between the control unit and the personal computer is a wireless modem. The navigation system offered in the Cedric was modified for use as the vehicle location sensor and map database of the operations center. In experiments conducted on the system, information was transmitted from the control unit and shown on a digital map display on the personal computer screen in about ten seconds following activation of an emergency signal. 5 figs.

Development of practical solar-electric vehicle; Jitsuyo fukyugata solar denki jidosha no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Saito, S; Fujinaka, M [Tokyo Denki University, Tokyo (Japan)

1997-11-25

The paper reported on a Tokyo-Nagoya travel test on a practical spread type solar-electric vehicle, Solar-EV. A comparative study was made running the same type gasoline vehicle, GV. The measured power consumption amount of Solar-EV is 57.6 kWh. By converting it into Mcal unit, an energy consumption amount of 49.5 Mcal was obtained. Further, as to GV, the energy consumption amount of 316 Mcal was obtained using the amount of supply of gasoline (mean heating value: 8.4 Mcal/h) of 37.6 l and the fuel consumption of 16.2 km/l. Accordingly, the energy consumption amount of Solar-EV became a sixth of that of GV. In the cost comparison, the cost of Solar-EV was 1,440 yen (power source price: 25 yen/kWh), which is about a third of that of GV, 3760 yen (gasoline unit price: 100 yen/l). Monocrystal Si solar cells, 270W, installed on hood/roof are connected to the main 288V system (the auxiliary 12V system is amorphous Si), and generate power 4.4 kWh during travel. A total power consumption amount of Solar-EV in the total travel (Tokyo-Nagoya) is 79.9 kWh including the auxiliary system, approximately 6% of which was to be supplied from solar cells. 1 ref., 6 figs., 3 tabs.

Development of puncture resistance tire tube; Nirinsha no taipankusei kojo cube no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Yamagiwa, T; Nakayama, K; Kiyota, S; Tanaka, A [Honda R and D Co. Ltd., Tokyo (Japan); Makisaka, N

1997-10-01

A new tire tube with a puncture resistance function was developed. The tube is a two-chamber structure having an air chamber and a liquid chamber, and the liquid chamber at the crown-side half of the tube is filled with an anti-puncture sealant during a manufacturing process. In a market test, it was confirmed that the number of puncture cases were reduced by 90 % in comparison with conventional tire tubes by using the newly developed tube. This paper describes the structure of the tube and the characteristics of the tube rubber, and the manufacturing process and durability of the tube. 3 refs., 17 figs.

Advanced soft coverpad made of non-woven fabric; Soft fushokufu coverpad no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Hayakawa, t; Kamezaki, K; Tokita, T [Takashimaya Nippatsu Kogyo, Aichi (Japan); Yamada, Y; Ono, H; Araki, O [Toyota Motor Corp., Aichi (Japan)

1997-10-01

At the present expected to enhance the product-value of automobile, it can be considered that advancement of touching and fitting feeling of seat would be important factors. For the purpose of materializing of these factors, We have noted softening of seat cover and carried out development of cover pad made of non-woven fablic. As a result of pursuing compatibility of soft feeling and durability of the cover pad, we could achieve to ensure the quality required for the material as the seat cover pad. 3 refs., 15 figs., 4 tabs.

Advanced slab polyurethane foam with feather touch; Soft feather urethane foam no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Yamada, Y; Ono, H [Toyota Motor Corp., Aichi (Japan); Mori, A; Yamaguchi, N; Nakamura, T [Bridgestone Corp., Tokyo (Japan)

1997-10-01

Automotive seat plays an important part, which are not only retention of sitting position, but also comfort and high-class feeling. Wadding, which is a part of the seat, is a key component for the sitting comfortableness. This paper is concerned with advanced slab polyurethane foam with feather touch feeling. The compounding of formation, foaming process and reliability of mass production is studied. 2 refs., 10 figs., 3 tabs.

Development of S-wave portable vibrator; S ha potable vibrator shingen no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kaida, Y; Matsubara, Y [OYO Corp., Tokyo (Japan); Nijhof, V; Brouwer, J

1996-05-01

An S-wave portable vibrator to serve as a seismic source has been developed for the purpose of applying the shallow-layer reflection method to the study of the soil ground. The author, et al., who previously developed a P-wave portable vibrator has now developed an S-wave version, considering the advantage of the S-wave over the P-wave in that, for example, the S-wave velocity may be directly compared with the N-value representing ground strength and that the S-wave travels more slowly than the P-wave through sticky soil promising a higher-resolution exploration. The experimentally constructed S-wave vibrator consists of a conventional P-wave vibrator and an L-type wooden base plate combined therewith. Serving as the monitor for vibration is a conventional accelerometer without any modification. The applicability test was carried out at a location where a plank hammering test was once conducted for reflection aided exploration, and the result was compared with that of the plank hammering test. As the result, it was found that after some preliminary treatment the results of the two tests were roughly the same but that both reflected waves were a little sharper in the S-wave vibrator test than in the plank hammering test. 4 refs., 9 figs., 1 tab.

R and D of remote reading system. Remote reading system no kaihatsu kenkyu

Energy Technology Data Exchange (ETDEWEB)

Nakano, H.; Hamada, T.; Nakamura, O. (The Kansai Electric Power Co. Inc., Osaka (Japan)); Imai, Y.; Akiyama, K.

1992-03-25

As measures for the spots difficult in metering within a framework to integrally automate the power distribution, a remote reading system was prototypically tested and evaluated in reliability on the actual field. The system methodically selected the signal {prime}s line injection, high frequency wave signal and voltage detection, while the signal frequency, transmission rate and highest transmission output were set at approx. 3.5KHz, 7.5bps and 50dBm, respectively from the test result. The demonstration test on reliability of the system locatively selected a vicinity of high voltage consumer, high harmonic wave-generating consumer, transforming station, etc. The total ratio of success in reception was comparatively high in Kuzuno and Yamazaki areas, but low in Kamojyo and Ichinomiya areas, The badness in reception was caused by the fluctuation in noise and strongness in damping which was influenced by the condenser in the high voltage consumer. The locative relation between the parent and child stations of system, and high voltage consumer being classified into four patters, an application table of remote reading system was prepared by simulation. 14 figs., 6 tabs.

Development of new-concept superconducting power equipment; Shinkino chodendo denryoku kiki no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Hamajima, T.; Tsurunaga, K.; Urata, M. [Toshiba Corp., Tokyo (Japan)

1998-01-01

The superconducting magnet energy storage (SMES) system has a function by which magnetic energy is stored in a superconducting coil without loss and discharged very rapidly into the power line when needed. The fault current limiter has a function by which transport current is passed without impedance and excessive fault current is restricted by generating large impedance in an emergency. These are the functions of new power equipment, which can not be realized by the conventional equipment. In the small-scale SMES project, Toshiba has fabricated 100 kWh-class element coils and 1 kWh/1 MW modules as the first step of practical application for power system control. For the superconducting fault current limiter, Toshiba has developed a 6.6 kV-1 kA class fault current limiter without supplying cooling medium such as helium, and limiting tests of fault current have been successfully conducted. Through the long-term tests of element coils for SMES and the system interconnection tests of module-type SMES, it is expected that the technological development for practical application is accelerated. 4 refs., 7 figs., 3 tabs.

Development of the Nissan hydraulic active suspension. Nissan yuatsu active suspension no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kawarasaki, y.; Fukunaga, Y.; Hasegawa, S.; Okuyama, Y.; Omura, I.; Takahashi, K.; Abe, S.; Tsuruta, E. (Nissan Motor Co. Ltd., Tokyo (Japan))

1989-12-25

A hydraulic active suspension system, Nissan original product, was developed and mass produced for the first time in the world. The system incorporates a sufficient power source, a high accuracy sensor and a high response device for continuous and intended vehicle control and at the same time delivers high levels of ride comfort and driving performance. The suspension system has four innovative features: skyhook damping, active roll and pitching control, a frequency-dependent damping mechanism, and active steering characteristics control. Under all road and operating conditions, the system actively suppresses vehicle attitude changes and unnecessary movement, and also gently absorbs inputs from the road. This epoch-making system provides a dramatic improvement in vehicle performance, and has been adopted in the Infiniti Q45 luxury sedan. 2 refs., 20 figs., 4 tabs.

Development of pressurized coal partial combustor; Kaatsu sekitan bubun nenshoro gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kawamura, K [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Tanaka, T [Chubu Electric Power Co. Inc., Nagoya (Japan); Muramatsu, T [Electric Power Development Co. Ltd., Tokyo (Japan)

1996-09-01

The coal partial combustor (CPC) uses a combustion technology with which coal is burned at elevated temperatures and under revolution, the constituents are captured on the furnace wall and removed as molten slag from the furnace. This is a combustion technology to reduce load of ash on subsequent devices. To generate a molten condition, it is necessary to raise the combustion temperature as high as possible (to about 1600 degC in the furnace), but this is effective for a gas turbine composite power generation system. An efficiency of higher than 45% may be expected at the power transmission terminal. As an operation on subsidy from the Agency of Natural Resources and Energy, the normal-pressure CPC technology has already been established, and a research on pressurized CPC is being progressed since fiscal 1991. The research is in progress with a schedule that elemental tests for 7 tons per day production are conducted until fiscal 1995, a 25 tons per day pilot plant will be completed by November 1997, and verification tests for long-term continuous operation will be implemented until 1998. The 7 tons per day elemental tests have identified gasification performance and slag extraction performance using five types of coal having different properties. 7 refs., 10 figs., 4 tabs.

Development of film antenna for diversity reception; Diversity taio film antenna no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Shigeta, K; Taniguchi, T; Kubota, K [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

Based on the principle of capacitance-loaded window antennas, a new film antenna construction pasting an antenna element on a defogger element printed on a rear window was found. The film antennas show high reception performance, and can be used as television diversity antennas or a VICS-FM multiplex antenna. This paper describes the antenna design concept, the antenna construction and the application to a recreational vehicle which styling is 1.3-Box wagon for the electric accessory. 2 refs., 11 figs.

Development of crankshaft dynamic stress prediction; Jitsudoji crankshaft oryoku yosoku shuho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takahashi, S; Iwamoto, A; Miyazawa, H; Sato, K; Ozaki, H [Honda R and D Co. Ltd., Tokyo (Japan)

1997-10-01

In this paper, the development of the simulation model which predicts the stress of the crankshaft under running condition precisely is described. This simulation model considers about the nonlinearity of the oil film stiffness in the main bearing, the dynamic characteristic of the crankshaft system including resonance and the cylinder block stiffness. By the development of this stress analysis simulation, the stress m each part of the crankshaft during durability testing could be precisely predicted. 1 ref., 10 figs.

Development of low light-off catalyst; Teion kassei ni sugureta shokubai no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Takemoto, T; Ichikawa, S; Koda, Y; Yamamoto, E; Sumida, H; Yamada, H; Shigetsu, M; Komatsu, K [Mazda Motor Corp., Tokyo (Japan)

1997-10-01

A new type of three way catalyst was developed in order to reduce HC, CO and NOx in cold exhaust gas. This catalyst consists of double layer, and has a base support material of alumina and oxygen storage components (OSC) loaded with active metals including platinum. palladium and rhodium. It has good light-off performance and high catalytic activity. This catalyst includes two types of OSC. One is CeO2, and the other is CePrO2 that makes possible to improve NOx conversion at high exhaust gas temperature. 8 refs., 13 figs., 2 tabs.

Development of mechanical shield docking method; MSD (mekanikaru/shirudo/dokkingu) koho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Yokota, I. [Tokyo Metroplitan Government Water Supply Bureau, Tokyo (Japan); Watanabe, T.; Hagiwara, H. [Shimizu Corp., Tokyo (Japan); Nishitake, S. [Mitsubishi Heavy Industries Ltd., Tokyo (Japan); Endo, M. [Obayashi Corp., Osaka (Japan)

1993-09-20

For the construction works of underground tunnels, mainly the shield method has so far been adopted, but in order to make underground junction of shield machines, the method of utilizing a shaft or the method of improving the earth by the auxiliary methods such as chemical feeding have been adopted. However, either method has restriction for its practical application. The MSD method uses no auxiliary method at all, can join directly two shield machines mechanically underground, has high water stoppability at its junction, is applicable for either of shield machines of slush type or mud pressure type, and is the method to solve totally various problems in the existing joining methods. This method is the one that two shield machines, one on the out-pushing side and another on the in-receiving side, progress from both sides and face each other, then the both are joined mechanically for unification by pushing a steel penetration ring built-in the out-pushing shield machine to the rubber ring built-in the penetration chamber of the in-receiving shield machine. After joining, the shield machines are disassembled for removal leaving the junction only, and the secondary lining is done with concrete. 6 figs.

Jet engine R and D and I; Watashi to jet engine kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Murashima, K. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

1998-06-10

My efforts towards at the development of aeroengines since the end of the war are described. The J3-7 engine propelled the T1 trainer plane, and was installed as booster aboard the P2J antisubmarine patrol aircraft. It was the first jet engine that Japan produced after the end of the war, and had been in use until quite recently. I took part in the construction of a prototype of the JR100 series designed to serve as VTOL (vertical take-off and landing) aircraft lift engines, and in the test thereof. As the shift from turbojet to turbofan proceeded, I participated in the development of the FJR710 engine under the guidance of National Aerospace Laboratory, and the product was installed aboard an experimental STOL (short take-off and landing) aircraft Asuka. I next joined a Defense Agency initiative for a reheat turbofan to replace the J3 aboard trainer plane, and the result was the low bypass ratio/high output F3 engine. In 1989, Ministry of International Trade and Industry decided for a large-scale project of developing an engine for a next-generation supersonic transport, and the HYPR (Super/Hypersonic Transport Propulsion System) project was started. The project was participated in by manufacturers from overseas, which were GE, P and W, RR, and SNECMA. The foreign corporations worked on an equal footing with the Japanese parties, and collaboration between the participants was smooth, with each party endeavoring in the field they were good at. The project will be concluded as scheduled in fiscal 1998. (NEDO)

Current status and future of space development; Uchu kaihatsu no genjo to shorai

Energy Technology Data Exchange (ETDEWEB)

Matokawa, Y. [Institute of the Space and Astronautical Science, Tokyo (Japan)

1998-05-01

Space development has an aspect of contributing to livelihoods. Various types of satellites, such as those for weather forecasting, TV broadcasting, international communication (telephone and internet systems), and GPS-aided car navigation, have been already launched. Space science of the 20th century roughly tells the history of some 15 billion years from the big bang to birth of mankind as a spectacular story. The international space station, construction of which is to be started in 1998, should drastically enlarge man`s experiences in the universe. The space activity plans for the future draw various dreams, such as spaceplane, lunar base, solar generator satellite, Mars base, space colony, skyhook, and so on. Dreams of mankind have been eventually realized in the past history. It is time to deliberately assess what are meant by the space development of the 20th century, and to review ideal directions of the space development for the next 100 or 1000 years. 6 figs.

Technical research and development of long-spanned bridges; Chodai kyoryo no gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sakai, F.; Yamanaka, M.; Ogawa, K.; Mizukami, Y.; Kano, J.; Watanabe, K. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

1996-10-15

Outlined herein is technical development of long-spanned bridges represented by suspension and cable-stayed bridges. The design of long-spanned bridges requires theoretical analysis of flexibility in which balance after they are deformed by load is taken into consideration. The matrix finite displacement analysis program is developed for optimizing cable-stayed bridge designs and determining suspension bridge shapes as the new major functions. The analysis program, named KASTAN, is also developed for stress analysis of the structure details. A wind tunnel for structure designs is installed to analyze resistance to wind. A number of experiments have been carried out by the tunnel for the designs of segment, main tower and overall bridge models. The means of controlling wind-caused vibration include hydraulic dampers, mass dampers, and combination of high damping rubber and spacer. Cable-stayed bridges are highly flexible, their types being selected by tower height and shape, span ratio and shape of the main beam, and cable position. These bridges constructed by the company include the S-shaped ones whose main beams are supported by cables suspended by two towers of different height, and the others with H-shape towers of high columns which are connected to each other by horizontal beams. 11 refs., 15 figs.

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of next-generation thin-film solar cell module manufacturing technology - Development of CIS solar cell module manufacturing technology - Development of high-quality film enlargement technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu / kohinshitsumaku no daimensekika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project aims to establish a manufacturing process that enables both high-quality CuInSe{sub 2} (CIS) film solar cell enlargement and cost reduction and to develop a device structure which uses less heavy metal for the purposes of increasing the CIS thin-film solar cell size and efficiency and decreasing environmental impact. Several element technologies have been established for increasing the area of high-efficiency Cu(In, Ga)Se{sub 2} (CIGS) solar cells. Concerning the enlargement of the photoabsorption layer which is to assume the most important role, it is found that a high-quality CIGS film, which is near homogeneous though within a 10cm times 10cm area, is fabricated by an in-line vapor deposition method. As for dead area reduction and high-speed patterning, it is found that laser scribing works effectively in the patterning of the window layer and photoabsorption layer. As for reduction in the use of heavy metal, a high efficiency of 16.2% is attained in a cell not using a CdS film as expected in the case of a cell using a CdS film, this thanks to a CIGS film surface reforming technique. The technique of junction formation for CIGS solar cells is improved, and then a true efficiency of 18.5% is achieved. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of structure control materials / R and D of multi-stimuli-responsive materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (kozo seigyo zairyo gijutsu kaihatsu) kodo shigeki oto zairyo no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described multi-stimuli-responsive materials out of the technology developments for creating original high-functional materials under the system of R and D of industrial scientific technologies. These are materials which repeatedly reproduce functions such as separation, penetration and movement in response to stimuli by imitating living organisms. In relation to polymer multi-stimuli-responsive materials, various copolymers were synthesized using N-acetyl (meta) acrylamide, of which the synthesis method was established in the previous fiscal year, as a main component, and thermal responsive polymer with upper critical solution temperature which becomes a base of separation functional materials was searched for. By immobilizing it with molecular recognition ligand, measured was thermal dependence of affinity of the immobilized matter to albumin. Also studied were molecular recognition cell adhesion/separation functional materials. Concerning composite multi-stimuli-responsive materials, with the use of silica microcapsule surface-immobilized with silane coupling agent, studied were the optimum conditions for immobilizing thermo-responsive polymer to the surface of the capsule. Using motion functional materials by ion exchange resin, obtained was motion functionality which is satisfactory at the state of practical use. 94 refs., 82 figs., 16 tabs.

Development of a new electric battery electric power storage system. Results of the 12-year R and D; Shingata denchi denryoku chozo system kaihatsu. 12 nenkan no kenkyu kaihatsu no seika

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The paper described the results of the R and D which have been continued for 12 years on a new electric battery electric power storage system (load leveling function). The electric batteries for study were Na-S, Zn-Cl, Zn-Br, and redox type. Charge/discharge operation of 211 times was conducted of a pilot plant with a Na-S battery 1,000kW and 8-hour capacity. The overall efficiency of system was 71.5-76.0%, and the energy efficiency of battery was 86%. As a whole, the performance was able to be confirmed which can fulfil a developmental target. The system overall efficiency of 65.9% and battery efficiency of 76.1% were obtained. The experiment on battery life was carried out at plant together with the pilot operation. The mean life of Na-S battery was estimated at 800 cycles, and that of Zn-Br battery at 500-800 cycles. The effectiveness of the new electric battery electric power storage system was technically verified. For the future commercialization, studies on the following are needed: enhancement of reliability, easiness in maintenance/inspection, size reduction, cost reduction, etc. (NEDO)

Fiscal 1999 achievement report on research and development of industrial technologies. Research and development of synergy ceramics; 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are conducted in the two fields of (1) survey and research and (2) development of technology for evaluating high temperature dynamic corrosion characteristics of heat resistant ceramics. In field (1), a comprehensive survey is conducted, an application study is conducted about high temperature gas separating ceramic membranes, and efforts are made to put to practical use ceramic parts manufactured by a low cost production process. In the application study of ceramic membranes, technologies are developed for a process of manufacturing high temperature gas separating porous ceramic membranes capable of separating and purifying gas emissions and gas ingredients, which involves the development of technologies for improving on gas separation and purification functions, development of technology of providing catalyst support function, technology of porous membrane formation, evaluation of separation characteristics, and so forth. In an application study for ceramic parts manufactured by a low cost manufacturing process, which involves structural ceramics, optimization is accomplished for materials synthesizing technologies by means of mechanical alloying, and cylinder liners are fabricated and evaluated for a natural gas engine made of silicon nitride based ceramics. In field (2), a high temperature dynamic corrosion testing device is built for heat shield coatings. (NEDO)

Research and development of basic technologies for the next generation industries, 'ultra-grid elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'chokoshi soshi'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-04-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to ultra-grid elements. With regard to the process technology to search materials suitable for the targets of ultra-grid elements and manufacture ultra-grid element structure, a technology has been completed, by which crystalline growth is performed while controlling AlAs and GaAs at atom layer levels by using the MBE process and MOCVD process. This has allowed the understanding to be progressed on behavior of electrons in hetero interface or very thin films. It has also become possible to acquire new crystals that have band gaps and grid constants matching the performance of the elements. Regarding ultra-grid functional elements, new functional elements with the HET and RHET structures were made by utilizing the characteristics of the ultra grids, and performances of normal temperature operation and high speed operation were investigated. The ultra-grid structured elements have made it possible to embed ultra fine electrode structure into crystals by means of double hetero growth, and a possibility of Si-based PBT was demonstrated. These achievements lead to a belief that the targets intended at the beginning of the present research have been achieved. (NEDO)

Load leveling air conditioning technology development by unused energy high-level utilization. Summary of achievements by development themes; Miriyo energy kodo katsuyo fuka heijunka reidanbo gijutsu kaihatsu. Kaihatsu temabetsu seika gaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-01-01

This paper introduces a number of research and development cases on utilization of unutilized energies. In developing the component technology for a thermal plant utilizing low-temperature unutilized energies, the paper introduces a heat exchanger system to collect heat from sea water, a heat exchanger system to collect heat from waste heated area in subways and urban sewage plants, and a high-density heat transportation system using ice plus water slurry or PCM-C plus water slurry. Furthermore, with regard to the heat pump system using low-temperature unutilized hear sources, development was introduced on a 'heat source load responsive heat pump system', which combines a load variation responsive heat pump utilizing river waters with a latent heat storage system using nighttime electric power serving for electric power load leveling. In developing the component technology for a heat plant utilizing high-temperature unutilized energies, introduction was given on a turbine driven turbo type heat pump system, a high-efficiency absorption type heat pump, a waste heat driven absorption type freezer, and an urban type underground heat storage tank. (NEDO)

Fiscal 1999 research on geothermal energy development promotion. Research report on development feasibility (Strategic survey - nationwide survey); 1999 nendo chinetsu kaihatsu sokushin chosa hokokusho. Kaihatsu kanosei chosa (senryakuteki chosa zenkoku chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-10-01

Analysis and assessment were conducted for each of promising geothermal regions over large areas so as to contribute to the drafting of survey implementation plans and estimation of the amounts of recoverable geothermal reserves under the geothermal energy development promotion project. In this fiscal year, based on the manual compiled in the preceding fiscal year, studies were made on the six areas, which were the eastern part of Hokkaido, Toyoha-Niseko area, Iburi area, Bandai-Azuma area, Minamiaizu-Nasu area, and the island area. In region 1 in the eastern part of Hokkaido, a 48km{sup 2} was extracted in the vicinity of Mount Musa, with the amount of resources per 1km{sup 2} estimated at 12.34-56.02MWe. In region 2 in the eastern part of Hokkaido, promising geothermal regions I, II, III, and IV were extracted, with the amounts of resources per 1km{sup 2} estimated at 50MWe or more at III and part of IV. In the Toyoha-Niseko area, promising regions I and II were extracted, the amounts of resources estimated at 50MWe or more in both regions. For the Iburi area, it was concluded that there was a probability of not less than 90% that the amount of resources was 50MWe or more and it was proposed that an additional survey be conducted. As for the Bandai-Azuma, Minamiaizu-Nasu, and island areas, need of further surveys was pointed out. (NEDO)

Research on natural gas fuel injection system. Development of high-performance pressure regulator; Tennen gas yo nenryo funsha system no kenkyu kaihatsu. 1. Tennen gas nenryo funshayo no koseino regulator kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Kato, S; Ishii, M; Takigawa, B; Makabe, K; Harada, S; Ono, H [Nippon Carburetor Co. Ltd., Tokyo (Japan)

1997-10-01

With the aim of further reducing the exhaust emissions of natural-gas vehicles, vigorous research and development work is under way today on multi point gas injection (MPGI) system. In this studies, a high-performance pressure regulator, which is one of the main components of this MPGI system, has been newly developed. The results showed that a significantly better accuracy of the regulated pressure level using this regulator was obtained under the wide range of operating conditions, including instantaneously greater changes of fuel flow rate. In addition, the advanced studies of gaseous fuel injectors (GFIs) would be also conducted. 4 refs., 8 figs.

Fiscal 1995 survey report on the feasibility study of the environmentally friendly type coal utilization system. Feasibility study of the environmentally friendly type coal utilization system in Thailand; Kankyo chowagata sekitan riyo system kanosei chosa. Tai ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-06-01

The paper surveyed the present situation and future trend of economy, energy supply/demand, coal production/distribution/utilization and the environmental effects in Thailand. The survey on the coal utilization and its environmental effects was partially requested of the environmental research institute in Thailand. The amount of coal utilization in Thailand rapidly increased to nearly four times as large as that ten years ago mainly in terms of domestic lignite under the government`s policy on expansion of the domestic energy use. However, most of this domestic lignite is low-grade coal with low calories and high sulfur content, and the use of it was rapidly increased mostly in power generation sector without no adequate environmental measures taken. This caused an environmental problem on air pollution due to sulfur oxides at Mae Moh power plant in the north several years ago, and the damages to the regional residents, etc. were given much publicity by journalism and developed the social problem. Accordingly, Thai people are now critical of the coal resource exploration and the coal use expansion. Under the circumstances, the Ministry of Industry and the energy related ministries/offices are obliged to review their development/promotion plans. 84 figs., 99 tabs.

Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (General research on hydrogen energy subsystems); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso riyo subsystem no sogoteki kento

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-03-01

This report is composed of the part 1 'General research on hydrogen energy subsystems' and the part 2 'Outline of researches on every use pattern of hydrogen'. The part 1 outlines the fiscal 1975 activity and result, the latest research situation, the latest domestic and overseas R and D situations, some extracted problems, and the future research issues. The part 2 summarizes the research results of every committee with the following themes: (1) Hydrogen combustion technology (combustion characteristics and technology of hydrogen-methane mixture, home and industrial combustors, study on hydrogen energy system), (2) Fuel cell, (3) Automobile engine (merits and demerits of automobile hydrogen engine, problems and their possible solutions on hydrogen engine, urgent research issues), (4) Aircraft engine (prospect for hydrogen use in air transport in Japan, study on various systems around airports in hydrogen use, technical study on aircraft using hydrogen fuel), (5) Gas turbine, and (6) Chemical use of hydrogen. (NEDO)

Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in the Philippines; Kankyo chowagata sekitan riyo system kanosei chosa. Philippines ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Grasping the present situation of coal utilization technology in the Philippines, the paper proposed a feasibility study of introduction of the environmentally friendly type coal utilization system which seems to be needed in the future. (1) Introduction of the environmentally friendly type coal utilization system in the electric power generation sector: there are only four full-scale running coal thermal power plants in the Philippines. In the future, several coal thermal plants are planned to be constructed by 2005, but for the new installation, it is desirable to adopt fluidized bed boilers with wide application to coal kinds. In case of 0.3-1.0 million MW class plants, it is planned to adopt high grade import coals, and it will be natural to fire pulverized coal. For the processing of flue gas, it is a must to install desulfurization facilities and smoke/soot removal devices. (2) Utilization/development of domestic low grade coals: at the mine-mouth generating plant, it is necessary to investigate the economically minable amount of coal, confirm productivity, survey coal quality, etc., and select boiler. As to coal briquetting technology, it is necessary to examine coal quality for tests and make a thorough study of what technology is most suitable. 50 figs., 78 tabs.

Fiscal 2000 project on measures for assisting and diffusing environmentally-friendly coal utilization system introduction. CMG recovery/utilization system joint demonstration project; 2000 nendo kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo chosa hokoku. CMG kaishu riyo system kyodo jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A CMG (coal mine gas) recovery/utilization system was designed, constructed, and then demonstrated at a model coal mining district in Liaoning Province for the purpose of contributing to the solution of energy and environment related problems in China. The recovery system demonstration test, aiming to improve on safety and productivity of coal mining and to supply recovered gas with stability, involved gas drainage test boring, mine sealing, sealed gas induction control, centralized gas monitoring, etc., which were carried out at the coal mine working face. A utilization system demonstration test was conducted, and CMG would continue to be supplied to the current users and CMG utilization would be started at the other 6 coal mines. For the supply of CMG to large-scale gas consuming areas, steel materials were manufactured and processed for spherical gas holders and denitrification facilities, gas holders were constructed, pipe lines were installed, and a provisional gas supply was carried out. For the transfer and diffusion of the technology, Chinese engineers were trained in Japan and Japanese engineers were dispatched to China. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of high-quality amorphous material/substrate manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A microcrystalline Si thin film is used to form the i-layer of a narrow gap a-Si based thin film solar cell. Since a microcrystalline p-layer is to act as the seeding crystal layer for the microcrystalline i-layer, it has to be very high in crystallinity and therefore is produced under high hydrogen dilution conditions. In this process, a problem arises of the darkening of the underlying transparent SnO{sub 2} electrode. Since this is due to chemical reaction on the SnO{sub 2} surface layer, blackening is prevented by shortening the film fabrication time, and then an excellently microcrystalline p-layer is obtained. Furthermore, by inserting a microcrystalline i-film buffer layer of low fabrication rate into the p/i boundary, plasma damage on the microcrystalline p-layer is inhibited for the fabrication of a microcrystalline i-layer high in crystallinity at high film fabrication rates. A high Voc is then obtained even when the microcrystalline p-layer is very thin. If the hydrogen dilution rate is too low when the i-layer film fabrication rate is high, the initially fabricated layer turns out to be thick to the detriment of film performance. On the other hand, the p-layer or the buffer layer will be etched when the hydrogen dilution rate is too high. The problem is solved by continuously varying the hydrogen dilution rate from high to low during i-layer fabrication. (NEDO)

Achievement report on developing superconductor power applied technologies in fiscal 1999 (2). Research and development of superconductor wire materials, research and development of superconductor power generators, research of total systems, research and development of freezing systems, and verification tests; 1999 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu / chodendo hatsudenki no kenkyu kaihatsu / total system no kenkyu / reito system no kenkyu kaihatsu / jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to achieve higher efficiency, higher density, and higher stability in power systems, research and development has been performed on superconductor power generators. This paper summarizes the achievements thereof in fiscal 1999. A verification test was given on the rotor of an ultra high speed responding generator. In a sudden short circuit test using the different phase charging method, no anomalies were found such as quench generation and vibration changes, wherein the healthiness of the generator was verified. In the VVVF actuation test, knowledge was acquired on the actuation method when the ultra high speed responding generator is applied to a combined cycle plant. After the verification test has been completed, the disassembly inspections such as visual check and non-destructive test were performed. With regard to the vacuum leakage found in the rotor under very low temperatures, the causes were presumed and the countermeasures were discussed by observing the weld structures. In the design research, the conception design on the 200-MW pilot generator was reviewed by reflecting the results of the verification tests on the model generator. At the same time, trial design was made on a 600-MW target generator. In summarizing the overall research achievements, the achievements and evaluations were summarized on technological issues that have been allotted to each research member. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the application technology of functional protein complex (R and D of the high-functional maintenance technology for power plants); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Kinosei tanpakushitsu shugotai oyo gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In order to develop advanced maintenance technology for power generation facilities, application technology of functional protein complexes is under investigation. On a light controllable enzymatic reaction system, construction of a light controllable bio-reactor by physico-chemical and bio- chemical techniques, and structure and functions of a photosynthetic protein complex using thermophilic cyanobacteria as material are under investigation. On a molecular mechanism for recognition and reaction of receptor proteins, structure analysis and engineering application of glutamate receptor channels of a synaptic transmission system, and basic study and material proteins for artificial structures using endocytic micromachinery, and a multi-enzyme system for synthesis of glycosphingolipids are under investigation. On a complex oxidation/reduction system by genetic engineering technique, construction of a high- efficiency stable system with functionally arranged oxidoreductase and electron transmission systems in biomembranes is in promotion. Research work was also made on molecular assemblies for a functional protein system. 166 refs., 91 figs., 9 tabs.

Report on achievements in fiscal 1999. Research and development of immediately effective and innovative energy environment technology (Development of immediately effective and high-efficiency solar cell technology, development of high-quality ingot manufacturing technology, and development of high-efficiency cell making technology); 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu seika hokokusho. Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu (kohinshitsu ingot seizo gijutsu kaihatsu / kohinshitsu cell ka gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been made on improving quality of ingots for substrates, manufacturing high-quality thin type substrates, and making high-efficiency cells. This paper summarizes the achievements in fiscal 1999. In developing the high-quality ingot manufacturing technology, discussions were given on a method for assessing impurities and crystal defects by using the total reflection scattering type infrared tomography, and on the optimal solidifying and cooling conditions during the ingot manufacturing by using simulation calculation for solidification. As a result of analyses and discussions, such findings were found effective that the ingot should be solidified through making the solid-liquid interface shape flat, and the temperature falling rate in an ingot should be maintained constant. In developing the high-efficiency cell making technology, discussions were given on the optimal construction based on a simulation that assumes the light sealing structure using the RIE method, and on the optimal construction of polycrystalline silicon solar cells by using a device simulator (PCID). The important factors in achieving a conversion efficiency of 20% are the light sealing structure, surface passivation, and substrate thickness. (NEDO)

FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for fabrication of thin-film solar cells/materials and substrates (Development of technologies for fabrication of high-quality amorphous materials and substrates); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for the amorphous/microcrystalline solar cells with the thin microcrystalline silicon film as the i layer, and the FY 1999 results are reported. The fabrication technologies are investigated for the microcrystalline silicon solar cells of pin or nip structure by RF or VHF plasma CVD using SiH{sub 4} and H{sub 2} as the stock gases. The tests are conducted for evaluating characteristics of the thin microcrystalline silicon film, to investigate the effects of film-making pressure, power and hydrogen dilution rate on the characteristics at a constant film-making temperature of 180 degrees C. The researches on the fabrication technologies for the microcrystalline solar cell of pin structure confirm that use of VHF plasma CVD improves crystallinity, electrical and optical characteristics of the p-type thin microcrystalline silicon film. The researches on the fabrication technologies for the microcrystalline solar cell of nip structure covers transparent substrates, film-making speed of the p layer, power and substrates, and a conversion efficiency of 7.5% is realized by the solar cell formed on a texture substrate. (NEDO)

Achievement report for fiscal 1998 on the development of superconductor power application technology. 2. Research and development of superconducting wire and superconductive power generator, research of total system, research and development of refrigeration system, and verification test; 1998 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total sytsem no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The slow excitation response type power generator is studied when the rotor and stator of a 70,000kW-class model are combinedly subjected to an on-site verification test, when a good result is obtained. The rotor is disassembled for inspection, and its members are found to be sound without any problem in terms of mechanical strength. The quick excitation response type is studied when a 70,000kW model is experimentally built and subjected to an on-site verification test after a rotation and excitation test in the factory, when the pilot machine concept design is reviewed. In the study of a total system, efforts continue for the review of the model machine test method, improvement on generator design and analytical methods, development of operating methods, and the effect of its introduction into the power system. Since a He-refrigerated system is requested to exhibit high reliability for application to power equipment and to be capable of continuous long-period operation, a system having constituents with their reliability enhanced and an appropriate redundant system is developed, and a verification study is under way which will continue for more than 10,000 hours. Described also is an oil-free low-temperature turbo refrigerator. The latest quick excitation response type rotor is also tested for verification. (NEDO)

Fiscal 1997 R an D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (high-efficiency and analysis and manipulation technology for DNA); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Through the observation of super spiral DNA fixed on a spermin or spermidine treated mica substrate by AFM (atomic force microscope), fixation of DNA without any deformation in solution was clarified, and visualization of the spiral structure of DNA were successfully achieved. Manipulation of Xe atoms adsorbed on an Si(111) surface was certainly possible by using STM (scanning tunneling microscope)/atom probe equipment. A nucleation mechanism in crystal growth was studied for various organic source-molecules/GaAs(001) surface systems, and formation of high-density nuclei on the GaAs surface was achieved by accelerating the translational energy of Ga material molecules up to 6eV or more. Ziegler- Natta catalysis important for industrial polymerization of olefin molecules was precisely analyzed by first-principle dynamic simulation. A large-scale simulation of zeolite catalyst is also in promotion for methanol to gasoline conversion. 51 refs., 87 figs., 7 tabs.

Report on the achievements in development of a coal liquefaction technology (a solvent extraction and liquefaction technology) in the Sunshine Project in fiscal 1981. Data 1. Development of a brown coal based solvent extraction plant (50 t/d pilot plant); 1981 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho (shiryo 1). Yozai chushutsu ekika gijutsu no kaihatsu (kattankei yozai chushutsu plant no kaihatsu (50ton/nichi pilot plant no kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This paper describes the data-1 for developing a brown coal based solvent extraction plant in the Sunshine Project in fiscal 1981. The data are for the development of a liquefaction plant for Victoria brown coal produced in Australia (a 50-t/d pilot plant). Fiscal 1981 has performed detailed design on the primary hydrogenation system by using the process conception and the design data obtained in the element studies. Part of the machines and devices was procured, and the site construction was begun. Detailed design documents and drawings were prepared. The data collected in relation with the plant design included the followings: device lists, entire factory layout drawings, device arrangement drawings, process flow sheets, utility flow sheets (fuel gas and fuel oil systems, steam and condensate systems, air for instrumentation, plant air, cooling water supply and return, industrial water and treated water, a waste water treatment system, a nitrogen system, and a waste gas system), public pollution preventing facilities, hazardous location classifying plans, and material balances. The data collected in relation with the machine design included pressure vessel engineering specifications, heat exchanger engineering specifications, and device purchase specifications. (NEDO)

Report on results for fiscal 1997 on development of superconducting electric power application technology. Pt. 2. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

This report refers, continuously to the Part 1, to the in-situ verification test of the slow-response type model machine rotor and to the review of the conceptual design of the pilot machine. On the basis of the R and D results of various element technology/partial models obtained before the previous fiscal year, the design, manufacturing and factory test had been conducted for a 70,000kW class slow-response type model machine rotor. This year, an in-situ verification test was performed to complete the test of all planned test items. Using the technological results obtained in the design, manufacturing and test of the 70,000kW class model machine, the conceptual design is being reviewed of the 200,000kW class pilot machine. In the aspect of the functional design, accurate grasping of the thermal load is essential for the purpose of attaining a large capacity for a superconducting generator, as a part of which a thermal load analytical method was planned to be established for a torque tube heat exchanger. The reasonableness of the analysis was verified through a comparison with the factory test result of the 70,000kW class slow-response type rotor, indicating good agreement between the calculation result and the actual measurement, and enabling the result to be obtained that explains dependency of the thermal load on the number of revolution. (NEDO)

Achievement report on developing superconductor power applied technologies in fiscal 1999 (1). Research and development of superconductor wire materials, research and development of superconductor power generators, research of total systems, research and development of freezing systems, and verification tests; 1999 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu / chodendo hatsudenki no kenkyu kaihatsu / total system no kenkyu / reito system no kenkyu kaihatsu / jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to achieve higher efficiency, higher density, and higher stability in power systems, research and development has been performed on superconductor power applied technologies. This paper summarizes the achievements thereof in fiscal 1999. In research and development of the superconductor wire materials, decrease in loss and increase in capacity of the conductors were progressed for the Nb{sub 3}Sn wire material, whereas its mechanical properties and stability were evaluated. In research and development of the superconductor generators, an ultra high speed responding generator was verified of its healthiness in a sudden short circuit test. A linkage test with an operating 77-kV system was performed, wherein verification was given that the superconductor generator can be operated stably against various disturbances. In research and development of the freezing systems, an improved system was structured, which achieved operation of 11,390 hours in a single system as a result of the high reliability of the oil-free structure. In the verification tests, the ultra high speed responding model generator was connect to the freezing system to give such tests as load test, onerous test, actuation test by using the M-G system, and 77-kV system linkage test. The functions, reliability, and durability of the system were verified, and different data were acquired. (NEDO)

Research and development of utilization technology of solar thermal system for industrial and other use. Development of system of advanced heat process type (chemical refrigeration and cold storage system using solar heat); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Advanced heat process gata system no kaihatsu (taiyonetsu reito reizo no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for chemical refrigeration and cold storage system using solar heat. The study on refrigeration materials are aimed at development of new hydrogen-occluding alloys which show good hydrogenation equilibrium characteristics and reactivity at temperature required for stand-alone refrigeration systems aided by solar heat, and still new hydrogen-occluding alloys operable at refrigeration temperature for lower-temperature systems. For the refrigeration materials capable of producing low-temperature heat of -10{degree}C at a regeneration temperature of 140{degree}C produced by solar heat, a La-Ni-Mn-Al alloy is selected for high-temperature use and a La-Y-Ni-Mn alloy for low-temperature use. The study on technology for refrigeration modules develops high-efficiency heat exchangers for refrigeration and regeneration, compatible with the hydrogen-occluding alloys. It also develops air-and water-cooling techniques for hydrogen-occluding alloys, where air is used as the heat source. The test apparatus is designed, installed and operated, to attain a low temperature of -10{degree}C or lower with a heat source of 140{degree}C and air heat source of 28{degree}C. 7 figs.

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of micro-array for next generation gene analysis (1st fiscal year); 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Jisedai idenshi kaiseki micro array no kaihatsu (daiichi nendo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are under way to construct a novel DNA (deoxyribonucleic acid) micro-array for gene diagnosis on the basis of technologies of laser scan type manipulation, nanometric position detection, and micro-machining. Using these technologies, structural changes to accompany reactions induced in the probe DNA deposited on an array are detected for the identification of the DNA. Activities are conducted in the four fields of (1) the study of probe DNA fixation technology, (2) development of an optical detection system, (3) detailed check of DNA micro-array performance evaluation technologies, and (4) a comprehensive survey. In field (1), gold colloid modified DNA molecules are designed and evaluated, and the fixation of DNA to substrates and technologies for integration are studied. In field (2), the gold colloid modified DNA is fixed on a thin gold film, and then a surface plasmon resonance (SPR) is observed in the wake of hybridization. Furthermore, a Brownian motion is observed of the metal particles fixed on a glass substrate via DNA. (NEDO)

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of system-on-chip mobile IC power source (1st fiscal year); 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. System on chip mobile IC dengen no kaihatsu (daiichinendo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are made to develop a switched capacitor (SC) integration technology based on the technology of switched capacitor power sources capable of efficiently performing voltage conversion without using magnetic parts such as coils. Activities are conducted in the six fields of (1) deciding on a programmable SC circuit, (2) circuit simulation, (3) layout design, (4) marketing and the contents and results of the studies, (5) profitability and the contents and results of the studies, and (6) a patent information survey. In field (1), a series fixed type DC-DC converter and a ring type converter are compared with each other in terms of electrical and theoretical characteristics, the number of devices to constitute the circuit, and ease of control, and the ring type converter is selected to serve as a general purpose SC power source. An efficiency simulation is conducted, as the result of which it is proved that the power source have the features that a practical power source should have. In field (2), for carrying out integration for the selected SC power source, a circuit simulation is conducted for the disclosure of IC power source constituent characteristics and dimensions are determined for the layout. (NEDO)

Fiscal 2000 achievement report on research and development of industrial technologies. Research and development of synergy ceramics (Research and development of ultrahigh temperature gas turbine for power generation); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (hatsuden'yo chokoon gas turbine no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The fruits of fiscal 2000 efforts to develop high temperature energy materials and ultraprecision materials are briefly described. Activities are conducted in the four fields of (1) materials derivation and advanced evaluation/design technologies, (2) application technologies, (3) common base technologies, and (4) multifunction realization process evaluation. Discussed in field (1) are high temperature energy materials, high performance active materials, fundamental technologies for member designing, active materials for dealing with environmental gas, silicon based high resistance energy materials, porous multiple layer ceramic materials, macro-/micro-scale stress analysis technology, and microfracture analysis technology. Discussed in field (2) are heat resistant and damage tolerant materials, heat shielding materials and energy absorbing materials, and nanofilter materials capable of selective separation. In the study of active materials specific for environmental gas, a catalyst is developed, stable at high temperatures and capable of treating NOx selectively. The catalyst is a layered product comprising Ba hexaaluminate layers and stabilized zirconia layers. (NEDO)

FY 1996 Report on the results of development of photovoltaic power generation system commercialization technologies. Development of device for producing compound semiconductors for photovoltaic cells (Development of flying tester); 1996 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchiyo kagobutsu handotai seizo sochi kaihatsu - hikoyo shikenki no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The compound semiconductor production process is tested under a microgravity by the space experiment/observation free flier (SFU), to reduce the photovoltaic power generation cost. Described herein are the FY 1996 results. The device is confirmed to work as planned by the full-scale test conducted in FY 1995, when it stood on the orbit and was recovered by the space shuttle STS-72 January, 1996. The recovered SFU-carried devices, including the electrical furnace and related subsystems, were found to normally function, and it was concluded that they could be evaluated and analyzed after the flight. The comprehensive evaluation and analysis of their electrical, mechanical, thermal functions have confirmed that they functioned and showed performance as planned, demonstrating validity of the designs and production procedures. The test samples were taken out of the recovered combined furnace, focus furnace and single-heat furnace for the space environment utilization tests. The other samples had much more uniform compositional distributions than those produced on the ground. (NEDO)

Report on achievements in fiscal 1999 on research and development of the industrial and scientific technology. Research and development of synergy ceramics (development of a technology to rationalize use of energies); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper summarizes the achievements in fiscal 1999 on research and development of a technology to use synergy ceramics as a material, its application technology and the common base technology. In the research of high-function active materials, development was made on catalyst and electrode materials having the selection, separation and rinsing functions, and discussions were given on materials for thermoelectric conversion of oxides. In the research and development of new thermoelectric conversion ceramics materials, searches were made on cobalt and nickel containing compound oxides. In the development of corrosion-resistant electrochemical cell materials, the honeycomb type was devised, and a technology was developed to form honeycombs laminated with different materials. In developing self-lubricating functional materials, silicon nitride with solid lubricant of MoO{sub 3} dispersed on the surface layer was developed, wherein tribological characteristics were evaluated. In developing ultra-smooth low friction materials, studies were carried out on reducing friction by controlling silicon nitride and its surface structure, placing lifter shims in an automotive engine as the application object. The joint research with the National Research Institute performed evaluations on the compound function manifestation process. (NEDO)

Fiscal 2000 achievement report on research and development of industrial technologies. Research and development of synergy ceramics (Research and development of ultrahigh temperature gas turbine for power generation); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (hatsuden'yo chokoon gas turbine no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The fruits of fiscal 2000 efforts to develop high temperature energy materials and ultraprecision materials are briefly described. Activities are conducted in the four fields of (1) materials derivation and advanced evaluation/design technologies, (2) application technologies, (3) common base technologies, and (4) multifunction realization process evaluation. Discussed in field (1) are high temperature energy materials, high performance active materials, fundamental technologies for member designing, active materials for dealing with environmental gas, silicon based high resistance energy materials, porous multiple layer ceramic materials, macro-/micro-scale stress analysis technology, and microfracture analysis technology. Discussed in field (2) are heat resistant and damage tolerant materials, heat shielding materials and energy absorbing materials, and nanofilter materials capable of selective separation. In the study of active materials specific for environmental gas, a catalyst is developed, stable at high temperatures and capable of treating NOx selectively. The catalyst is a layered product comprising Ba hexaaluminate layers and stabilized zirconia layers. (NEDO)

Survey for preparing the database for R and D of new engines. Waste power generation, solar heat system, geothermal power generation, clean energy vehicle, coal liquefaction/gasification, and combined systems; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Haikibutsu hatsuden, taiyonetsu riyo, chinetsu hatsuden, clean energy jidosha, sekitan ekika gas ka oyobi odanteki tema

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The present developmental conditions and issues of new energies are systematically arranged for effective promotion of their diffusion. One hundred and forty six general waste power generation facilities of 558,000kW are in operation in 1995, and among them 89 facilities supplies 1,080 GWh to power companies. 50 industrial waste power facilities of 247,000kW are in operation. 20,000 solar systems and 180,000 hot water heaters are in operation in 1995. Commercial geothermal power generation facilities of 490,000kW and private ones of 36,000kW are in operation. Introduction of expensive clean energy vehicles is making very slow progress. The pilot study on bituminous coal liquefaction is in promotion mainly by NEDO. The experiment of entrained bed coal gasification in Nakoso was successfully completed, and development of a commercial plant is to be expected. Power rates of 10 power companies were reduced in 1996, and unit purchase prices of surplus power of photovoltaic and wind power generation were also revised. The new menu and unit purchase price were announced in 1996 for surplus power of waste power generation and fuel cell. 67 figs., 284 tabs.

Achievement report for fiscal 2000 on the phase II research and development for the hydrogen utilizing international clean energy system technology (WE-NET). Task 1. Investigations and researched on system assessment; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 1. System hyoka ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for Task-1. Technologies drawing attentions relate to fuel cell driven automobiles and hybrid automobiles in the field of utilizing hydrogen derived from reproducible energies and fossil energies, and fuel cell co-generation and micro gas turbine co-generation in the field of electric power generation. Hydrogen reformed from gasoline on board the automobile as the fuel for fuel cell driven automobiles, hydrogen as a by-product of coke furnace off-gas (COG), and reproducible energy hydrogen have the same fuel consumption performance as in the hybrid automobiles. Particularly the COG is low in cost, and has large supply potential. Liquefied hydrogen is as promising as compressed hydrogen in view of the cost for automotive hydrogen supply stations. What has high economic performance as the self-sustaining systems for islands are photovoltaic and wind power generation, and the system using hydrogen as the secondary energy. Since much of the reproducible energies is used for electric power demand in Japan, the by-product hydrogen and the reformed hydrogen in an amount of 9.3 billion Nm{sup 3}/year would take care of majority of the demand in view of the short time period. For a longer time span, hydrogen originated from the reproduced energies in the Pan-Pacific Region should be introduced. (NEDO)

Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 2. Investigations and researched on safety measures; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 2. Anzen taisaku ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for Task-2, the safety measures. In order to structure safety design criteria, potential anomalies, accident phenomena, and safety measures that can be applied were put into order based on the conceptual designs on hydrogen supply stations. Items of information were collected and put into order on failure rates and other factors to estimate accident occurrence frequency required for quantitative risk assessment. Representative event scenarios were selected by estimating the event evolving processes. In order to obtain knowledge about the steady state of run-off and evaporation of liquefied hydrogen, experiments were performed by using a small-size experimenting device, whereas new findings were discovered. To identify the fundamental knowledge related to explosion of hydrogen, and to verify a program simulating the explosion, explosion experiments were inaugurated to have established the stable experiment performing method. A calculation program simulating leakage and evaporation of liquefied hydrogen was verified and analyzed from the experimental results, and the program improvements were discussed. Pre-estimation and verification were carried out on the explosion experiments by using the hydrogen explosion and combustion simulating calculation program, and discussions were given on program improvement. (NEDO)

Fiscal 1998 achievement report on regional consortium research and development project. Venture business fostering regional consortium in its 2nd year--Creation of key industries (Development of manufacturing system for multiple applications of biological resources); 1998 nendo yuyo seibutsu shigen no tamokuteki riyo no tame no kako seizo system no kenkyu kaihatsu seika hokokusho. 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development is conducted to collect intermediate products from Okinawan herbs for the production of antioxidant products usable for various purposes. Substance-producing plants are screened and the substances they offer are assessed for antioxidant activity, extracted, processed, prepared for market, and checked for safety. At the Okinawa Industrial Technology Center, a DPPH (1,1-diphenyl-2-picrylhydrazyl)/microplate method has been established, which promptly measures the antioxidant activity of the substances. Using this technology, the divisions concerned of industrial, academic, and governmental organizations cooperate with each other over the optimization of herb cultivation technology, development of a herbal ingredient analyzing technology, efficacy of herbs, development of a safety assessment system, development of a technology for the effective extraction, processing, and preparation of herbal ingredients, and the development of a technology of assessing antioxidant intermediate products for their efficacy. As the result, a technology is established of producing intermediate antioxidant products from Guava, Ryukyuyomogi, and Ukonisomatsu. They are unique Okinawan products, and sell at 40,000-50,000 yen. Since the prices are equal to or lower than the prices of other antioxidant intermediate products, probabilities are very high that they will get into markets in Japan proper. (NEDO)

Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 12. Search and assessment of innovative and leading technologies; Suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 12. Kakushinteki sendoteki kenkyu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Search and assessment were carried out on innovative and leading technologies which are outside the development objects at the present, but are promising for the future. This paper describes the achievements in fiscal 2000. In the hydrogen manufacturing method using natural gas as the raw material, but not generating carbon dioxide, a method using plasma has the hydrogen conversion rate of more than 90%, capable of providing carbon black with added value. On a hydrogen selective enzyme hydrogenase sensor, verification was given on its sensitivity and response speed, but the discussion was interrupted because of difficulty in obtaining the enzyme. Naphthenic hydrogen storage and transportation media (easy in hydrogenation and dehydrogenation) were discussed, whereas the reaction promoting effect was identified in both of the super heating liquid film process and the membrane reactor system. Enhancement in output and efficiency may be anticipated if hydrogen-rich reformed gas is obtained by reforming methane (natural gas) by utilizing waste heat from a gas turbine of several MW capacity. Hydrogen liquefaction technologies using the magnetic freezing process was discussed as the fundamental research assignment, wherein fiscal 2000 has studied the basic design and optimal magnetic materials. (NEDO)

Development of a wide-area energy utilization network system (research on a technology to design an energy system). FY 1998 report on achievements of research on systematizing ECO and ENERGY cities; Koiki energy riyo network system kaihatsu (energy system sekkei gijutsu no kenkyu). 1998 nendo eko ene toshi no system ka kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

As a research on systematizing ECO and ENERGY cities, surveys and analyses were performed on the actual state of introducing district heat supply systems utilizing difference waste heats including factory waste heat. Waste heat from electric power generation is utilized for district heat supply in Japan at 122 points or about 20% of the district heat supply points in operation as of March 1998. The number is in the increasing trend in recent years, and the future potential of its introduction can be said high as the history thereof is still short. Its introduction form is accounted mostly for by building cogeneration or plant cogeneration. Back-up facilities for the case when waste heat supply stops because of regular facility checks are provided by the heat supply business operators, which impede the economy of the system. In the U.S., the Public Utility Regulatory Policy act motivated installation of cogeneration and off-peak power generation systems for district heat supply. Technical maps (for waste heat sources and different waste heat utilization systems) were prepared based on the surveys to discuss the future measures. (NEDO)

FY 1993 report on the results of the subsidy project for the Sunshine Project. Development of coal use hydrogen production technology (Support study of pilot plant - Study using the small equipment); 1993 nendo Sunshine keikaku hojo jigyo seika hokokusho. Sekitan riyo suiso seizo gijutsu kaihatsu - Pilot plant no shien kenkyu (Kogata souchi ni yoru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

As to the development of coal use hydrogen production technology, the paper studied the reactivity of char and ignition characteristics of various coals in the use of electric furnace and the participation in pilot plant test and the improvement, and the FY 1993 results were reported. In the study of reactivity of char, it was found that the reactivity was the same, regardless of the equipment and kind of raw coal, if considered of the ratio of the total oxygen amount (the char-containing oxygen amount added to the oxygen supply amount) to the carbon supply amount in char. In the test on ignition characteristics of overseas coals, the same characteristics as those of the Taiheiyo coal conventionally tested were obtained and it was found that it was good to use the same method for start-up of gasifier as conventionally used. In the pilot plant test in the previous year, slag and ash stuck to the outlet of the gasification part and heat recovery part and developed, which hindered the continued operation. To improve it, the following were carried out: model study, study of ash sintering, study using the synthetic test equipment, analysis of the deposit in gasifier, etc. Based on these results, the plant was improved, and the continued operation of 1,149 hours was stably achieved in RUN8. (NEDO)

Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Development for practical application of a new production process); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Shinseizo process jitsuyoka kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The research and development aims to establish, through verification tests, practical application technologies for two methods, namely, a 'low-temperature liquid phase method' by which cost will be reduced thanks to simplified plant facilities and a 'vapor phase fluidized bed method' in which a composite reforming process may be combined for better economics of scale with a vapor phase fluidized methanol synthesizing method whose facilities may be built to be very large. For the former method, development efforts are made to enable catalyst performance characterization and low-temperature liquid phase methanol production using a small pyrolysis reactor. In the research on pyrolysis reaction, a Raney copper/KOMe/MeOH-based catalyst is used, and this attains a raw material gas conversion efficiency of 92.7%. In the construction of a low temperature liquid phase process, it is found that a single spun conversion efficiency of not less than 90% may be achieved using a heterogeneous catalyst. For the latter method, studies are conducted for the development of, and for the establishment of technologies for designing, synthetic gas production technologies in the development of a heat exchanger type composite reforming furnace and a fluidized bed methanol production process, the development of a catalyst manufacturing technology for fluidized bed practical application, the development of a fluidized bed methanol production technology, and the optimization of the process and its economic efficiency. (NEDO)

Achievement report for fiscal 1998. Research and development of synergy ceramics (Development of technology for energy use rationalization); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to create inorganic materials with their functions well harmonized and with their reliability remarkably improved, and efforts are made to establish basic technologies with which structural control may be carried out simultaneously for multiple layers in in-process products through positive utilization of various chemical reactions in the materials synthesizing process. This fiscal year's achievements are stated below. A low-temperature pressure nitriding method is developed in which nitriding reaction directly involves the metal aluminum compact for conversion into ceramics, and an aluminum sintered body is produced capable of high thermal conduction of not less than 170w/mk with the original compact shape retained. By a heat treatment in a high-temperature pressure nitriding atmosphere, a success is attained in producing a silicon nitride ceramic body enhanced (150w/mk) in thermal conduction. It is clarified that the microwave-aided selective heating technology works effectively in enhancing the particle growth rate in a liquid-phase sinter system, and a success is won in increasing strength by virtue of the formation of particle-growing particles. (NEDO)

Report on achievements in fiscal 1999. Research and development of micro-machine technologies (development of micro-factory technologies); 1999 nendo micro machine gijutsu no kenkyu kaihatsu seika hokokusho. Micro factory gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to achieve energy saving by micronizing the manufacturing processes of small industrial products, this research and development is intended to establish technologies to realize a micro-machine system, in which devices for processing, assembly, transportation and inspection used in the manufacturing processes are unified and incorporated in narrow spaces. Fiscal 1999 has performed, on the items of (1) research and development of the systematizing technologies and (2) comprehensive surveys and researches, with respect to the development of the first prototype system, and fabrication on the trial basis of devices to be mounted on the second prototype system, and discussions on further functional enhancement of the different devices. As a result in the research of the systematizing technology, the first prototype system was developed, that unifies the base unit fabricated in fiscal 1998, the electrolysis processing device, the fluid feeding device, the micro-arms, the coating device, the transportation device, and the environment recognizing device. The basic performances of the individual devices on the first prototype system were verified. Based on the result of this function verification, optimal design and fabrication on the trial basis of the devices mounted in the second prototype system were performed, and discussions were given on the further function enhancement in each functional device. (NEDO)

Achievement report for fiscal 1998. Research and development of synergy ceramics (Development of technology for energy use rationalization); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to create inorganic materials with their functions well harmonized and with their reliability remarkably improved, and efforts are made to establish basic technologies with which structural control may be carried out simultaneously for multiple layers in in-process products through positive utilization of various chemical reactions in the materials synthesizing process. This fiscal year's achievements are stated below. A low-temperature pressure nitriding method is developed in which nitriding reaction directly involves the metal aluminum compact for conversion into ceramics, and an aluminum sintered body is produced capable of high thermal conduction of not less than 170w/mk with the original compact shape retained. By a heat treatment in a high-temperature pressure nitriding atmosphere, a success is attained in producing a silicon nitride ceramic body enhanced (150w/mk) in thermal conduction. It is clarified that the microwave-aided selective heating technology works effectively in enhancing the particle growth rate in a liquid-phase sinter system, and a success is won in increasing strength by virtue of the formation of particle-growing particles. (NEDO)

Fiscal 1997 report of the development of high efficiency waste power generation technology. No.1 volume. Element technology development; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (yoso gijutsu kaihatsu). 1997 nendo hokokusho (daiichi bunsatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Following the previous fiscal year, the technology development was conducted of a high efficiency waste power generation system using general waste as fuel. In the development of high temperature high efficiency combustion furnace, a combustion test on the external circulating fluidized bed incinerator was made to obtain data on formation/decomposition of dioxins. Moreover, a combustion test was conducted using mock refuse, petroleum-derived waste and waste plastics, to confirm stabilized combustion characteristics and low pollution. In the development of a corrosion resistant superheater, made were the stress load high temperature corrosion test, study of intergranular corrosion by elements of impurities, etc. In the development of the environmental load reduction technology, conducted was the conceptional design of pulse plasma exhaust gas disposal equipment corresponding to the actual one. In the verification test in a pilot plant, the pilot plant passed the pre-use inspection and was completed in February 1998. In the study of an optimal total system, discussed were the data on the pilot plant verification test, measuring points, how to arrange them, etc. 2 refs., 88 figs., 50 tabs.

Study on the creation of inorganic materials using micro-gravity environment; Bisho juryoku kankyo riyo muki zairyo no sosei kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Creation of new functional inorganic materials using micro-gravity environment was studied. Observation of an electrode interface phenomenon under micro-gravity clarified that time variation in interference fringe is dependent on current density and electrode thickness in ground experiment, while it is dependent on not electrode thickness but current density under micro-gravity. In fabrication of glass fine particles under micro-gravity, true spherical glass fine particles of 4-7{mu}m in size were obtained corresponding to a charge of 40mg by evaporation and solidification of sodium tellurate glass as raw material under micro-gravity. In fabrication of non-harmonic Pb-Zn system alloy, the homogeneous alloy texture of 5{mu}m level was observed which has never been observed in previous metal phase diagrams by fusion of 80atom%Pb-20atom%Zn mixture under micro-gravity and quenching from 500degC. On the study on fabrication of spherical semiconductor crystals, 7 spherical Si single crystals of 300{mu}m in size were obtained. 12 refs., 48 figs., 2 tabs.

Transition of wind power utilization technology in the 20th century; 20 seiki ni okeru furyoku riyo gijutsu no hensen

Energy Technology Data Exchange (ETDEWEB)

Ushiyama, I. [Ashikaga Inst. of Tech., Tochigi (Japan)

2000-04-01

Windmills are one of the oldest prime movers and have been used for more than 700 years in Europe. The transition from low speed windmills for grain grinding and water pumping to high speed wind turbines for electric power generation had occurred at the end of 19{sup th} century. This paper, at first, reviews the windmill technologies and the researchers before 20th century. Then describes the back ground of how the wind power generator has existed and how the four pioneers developed their wind power generator. The historical developments of windmills to wind turbines in this century are studied focusing mainly on Danish activities. Then, the effort of the development of large wind turbine such as Smith-Putnum's first MW machine in U.S.A. and other mammoth machine concept are introduced. The new concept machines such as Savonius and Darrieus wind turbines in 1920s to 1930s are also explained. Finally, the novel technologies of wind turbine covering larger machines, variable speed generators, special wing sections for wind turbines, theoretical analysis method of wind turbine performance, offshore wind turbines, and wind turbine control technologies are stated. (author)

Forward prediction of tunnel face by use of equi-traveltime planes; Tosojimen no riyo ni yoru tunnel kiriha zenpo tansa

Energy Technology Data Exchange (ETDEWEB)

Ashida, Y [Kyoto University, Kyoto (Japan). Faculty of Engineering; Hirano, T [Nishimatsu Construction Co. Ltd., Tokyo (Japan)

1996-05-01

The result is reported herein of a depth transform algorithm application utilizing equi-traveltime planes in reflection seismic exploration for the purpose of knowing the structure configuration in front of the tunnel face in a tunnel excavation process. A vibration producing hole was provided 0.5m above the ground surface while a vibration receiving hole was provided at 1.5m above the ground surface, and the excavated lengths were 1.5m and 0.5m, respectively. There were 24 recording channels, from which inline offset records were taken. The on-site records were subjected to 100-1000Hz band pass filtering. The elastic wave propagation rate in the rock used for depth conversion was set at 400m/s in consideration of the distance and direct wave travel time from the vibration source to the vibration receiving point. As the result of study, weak layers were found in the neighborhood of 230-240m, 260-270m, and 280-290m. This method requires less core memory for calculation and completes calculation in a shorter period of time, which enables a conclusion that it will be effective in grasping the 3-dimensional structure in front of the tunnel face in the working scene. 4 refs., 7 figs.

Environmentally friendly type coal utilization technology transfer project. Downstream field; Kankyo chowagata sekitan riyo gijutsu iten jigyo. Karyu bun`ya

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper arranged the result of the clean coal technology transfer project carried out during October to December, 1996. For the purpose of supporting introduction/spread of clean coal technology (CCT) in Asian and Pacific countries, the project invited engineers of the countries to Japan, aiming at fermentation of the understanding of CCT and improvement in ability. The project was held by NEDO and managed by Center for Coal Utilization, Japan. The manager course is for policy decision makers, management and senior management (plant manager class). By taking up CCT assessment and a menu of economical efficiency, prepared was the environment to which CCT is introduced in case of working out policy and planning plant/equipment investment. Moreover, the engineer course is for policy planners, medium-class management (section chief class), senior engineers (planners), and takes up materials for judgment in case of planning CCT facilities and proposing measures to reduce environmental loads by management and improvement of facilities at the same time. Fifteen engineers were invited: 6 from China, 3 from Indonesia, 3 from the Philippines, and 3 from Thailand

Test results of cultivation of vegetables with fish breeding water; Yogyosui riyo ni yoru yasai saibai shiken kekka ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Nishida, S. [Hokuriku Electric Power Co. Inc., Toyama (Japan)

1997-10-28

Entrails of fish, fowls and domestic animals are mostly incinerated at large expenses, although partly used as foods. This study is to test `possibility of vegetable cultivation with fish breeding water,` where the entrail wastes are used as baits for fish breeding, and fish excretions are used as the fertilizer for vegetable cultivation to purify water for fish breeding. The cultivation bed consists of two sections, one for fish breeding/vegetable cultivation and the other for vegetable cultivation by the normal method. Vegetable grow notably less in the former than in the latter, 54.6 to 79.5 versus 100. Spinach contains slightly higher contents of vitamins A and C by 6 and 13%, when cultivated in the former than in the latter. Quantities of total nitrogen, phosphorus and potassium as the fertilizer components in the former are 49, 49 and 1.7% of those in the latter. It is predicted, judging from growth of the vegetables, that the former gives a harvest comparable with that by the latter, when given a 6 to 13 days longer cultivation period. 3 figs., 2 tabs.

Cement manufacture and sludge; Semento seizo to gesui odei. Semento kojo deno antei shori {center{underscore}dot} yuko riyo gijutsu

Energy Technology Data Exchange (ETDEWEB)

Hirota, Yoji; Yamazaki, Masayasu; Hashimoto, Koichi [Mitsubishi Materials Corp., Tokyo (Japan)

1998-11-10

There was the percussion of the sludge processing from the Kitakyushu City in 1995. Within various waste treatment technology cultivated to it, the technology (direct combustion system) of cement raw material by the direct injection of sludge dehydrated cake to cement baking furnace was adopted. It became dealing with in cement baking furnace of the Kurosaki factory in our company. Through the processing by the present, it is not completely finding even in cement quality of the product, environmental side and on the problem. It was confirmed to be the processing technology of sewage dewatered sludge in which this technology was safely stabilized. In addition, the superiority in much global environmental protection has also been confirmed. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, and development of technologies to manufacture amorphous silicon/thin film poly-crystalline silicon hybrid thin film solar cells); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo kaihatsu (oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu (amorphous silicon / usumaku takessho silicon hybrid usumaku taiyo denchi no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Developmental research has been performed on large-area low-cost manufacturing technologies on hybrid thin film solar cells of amorphous silicon and poly-crystalline silicon. This paper summarizes the achievements in fiscal 1999. The research has been performed on a texture construction formed naturally on silicon surface, and thin film poly-crystalline silicon cells with STAR structure having a rear side reflection layer to increase light absorption. The research achievements during the current fiscal year may be summarized as follows: the laser scribing technology for thin film poly-crystalline silicon was established, which is important for modularization, making fabrication of low-cost and large-area modules possible; a stabilization efficiency of 11.3% was achieved in a hybrid mini module comprising of ten-stage series integrated amorphous silicon and thin film poly-crystalline silicon; structures different hybrid modules were discussed, whereas an initial efficiency of 10.3% (38.78W) was achieved in a sub-module having a substrate size of 910 mm times 455 mm; and feasibility of forming large-area hybrid modules was demonstrated. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of next-generation thin-film solar cell manufacturing technology - Development of CIS solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu / CIS taiyo denchi module no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This research aims to achieve a conversion efficiency of 13% and a manufacturing cost of 140 yen/Wp with a 30cm times 30cm Cu(InGa)Se{sub 2}-based thin-film solar cell submodule. Ga and sulfur are combined and a film fabrication technology was developed which would improve on Voc. Concerning Ga, a laminated precursor layer was fabricated and evaluated, which comprised a Cu-25wt%Ga alloy layer and a Ga source which was a Cu-48%Ga alloy layer. Concerning sulfur, the vapor phase selenization temperature and the selenization retention time in an H{sub 2}Se gas atmosphere was allowed to vary for a change in Cu(InGa)Se{sub 2} calcopyrite crystallinity for the study of relations between the amount of sulfur taken in and the solar cell characteristics, and the relations were assessed by EPMA (electron probe microanalyzer). Technologies were developed for the fabrication of high-resistivity buffer layers by solution growth, for the fabrication of window layers (transparent, conductive ZnO film) by sputtering, and for their patterning. Submodules of a ZnO/Zn(O,S,OH)x/Mo structure were fabricated, 10cm times 30cm and 30cm times 30cm in size. The former achieved 12.5% in conversion efficiency, and the latter 11.6%. (NEDO)

Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system /development of technology to manufacture solar cells/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture silicon crystal based high-quality materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo denchi seizo gijutsu kaihatsu, usumaku taiyo denchi seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (silicon kesshokei kohinshitsu zairyo kiban no seizo gujutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

It is intended to develop thin film solar cells capable of mass production with high photo-stability and at low cost. Thus, the objective of the present research is to analyze the growth process of micro crystal silicon based thin films, the crystal being a high quality silicon crystal based material, and develop technology to manufacture high-quality micro crystal silicon thin films based on the findings therefrom. It was found that, when silicon source is available in cathode, pure hydrogen plasma forms micro crystal silicon films by using the plasma as a result of the chemical transportation effect from the silicon source. It was revealed that the crystal formation due to hydrogen plasma exposure is performed substantially by the crystals forming the films due to the chemical transportation effect, rather than crystallization in the vicinity of the surface. The crystal formation under this experiment was concluded that the formation takes place during film growth accompanied by diffusion of film forming precursors on the surface on which the film grows. According to the result obtained so far, the most important issue in the future is particularly the control of crystal growing azimuth by reducing the initially formed amorphous layer by controlling the stress in the initial phase for film formation, and by controlling the film forming precursors. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost large-area module manufacturing technologies, next generation thin film solar cell module manufacturing technologies, development of thin film poly-crystalline solar cell module manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development has been performed on a high throughput forming technology and a modularization technology for thin film poly-crystalline solar cell modules. This paper summarizes the achievements in fiscal 1999. In developing the high throughput forming technology for a high-quality thin film, research has been made on a low-cost VEST process to re-utilize substrates by separating the thin film from the substrate. In the melting re-crystallization process, it was discovered that plasticity deformation of the substrate can be reduced greatly by raising the substrate heating temperatures. It was also found out that substrate warping amount can be reduced to about one-fifth of the conventional amount by making the thickness greater than 1.5 mm and raising the heating temperatures higher than 1300 degree C. In developing the thin film modularization technology, it was indicated that the property improving effect remains the same even if the hydrogen passivation method is changed from the hydrogen ion injection to the hydrogen plasma processing. In the trial fabrication of the thin film modules, a conversion efficiency of 13.1% was achieved in nine-cell structured modules. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost large-area module manufacturing technology - Development of next-generation thin-film solar cell manufacturing technology - Development of thin-film polycrystalline solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu / jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (usumaku takessho taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to realize the practical application of the above-named solar module expected to exhibit higher efficiency and reliability and achieve cost reduction through consumption of less materials. In fiscal 1998, 1) technologies were developed to reduce substrate warpage during recrystallization for the higher-throughput fabrication of high-quality thin films and 2) technologies were also developed for the realization of higher-throughput fabrication of thin films and for efficiency improvement for thin-film modules. Under item 1), experiments were conducted by simulation for reducing warpage to occur in thin-film polycrystalline Si substrates during fabrication by melting and recrystallization. Under item 2), for the development of thin-film cell high-throughput technologies, studies were started on a more practical hydrogen plasma process to challenge the conventional process of crystal defect inactivation by hydrogen ion injection with which achievement of high throughputs is difficult. For the development of technologies for the enhancement of thin-film module efficiency, efforts were exerted to realize a 10cm times 10cm square shape for the enhancement of efficiency in the process of filling modules with cells. These efforts achieved a great step toward future practical application. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture thin film solar cells, development of technologies to manufacture low-cost large-area modules, development of technologies to manufacture next-generation thin film solar cells (development of technologies to manufacture CIS solar cell modules); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu, jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu (CIS taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Research and development was made with an objective to achieve conversion efficiency of 13% in a 30 cm times 30 cm size submodule of a CIS-based thin film solar cell, and to develop a manufacturing technology that can achieve 140 yen/Wp. This paper describes the achievements attained during fiscal 1997. In fiscal 1997, based on the achievements reached during the previous year, a submodule with a size of 10 cm times 30 cm was fabricated for an attempt of improving the open voltage and short circuit current density. Simultaneously, the applicability thereof to a module with an area as large as 30 cm times 30 cm was evaluated. As a result of experimental discussions, enhancement in the open voltage was verified by increasing amount of Ga or sulfur, but it was not possible to achieve 600 mV or higher. In the research of component technologies to establish a mass production process, research and development was made on a high-resistance buffer layer film forming technology, a high-quality window layer film forming technology, a high-quality metallic rear electrode film forming technology, and patterning technologies. The outdoor exposure test was continued on laminated mini-modules with a size of 10 cm times 10 cm. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost large-area module manufacturing technology (Development of next-generation thin-film solar cell manufacturing technology - Development of CIS solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu, Jisedai hakumaku taiyodenchi mojuru no seizo gijutsu kaihatsu (CIS taiyodenchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was carried out for the production of a Cu(InGa)Se{sub 2}-based thin-film solar cell submodules, having a conversion efficiency of 13% and an area of 30 cm times 30 cm, at a cost of 140 yen/Wp (at a production rate of 100 MW/year). In the effort to fabricate a large-area photoabsorption layer, reproducibility was improved by the introduction of a technique for controlling the Cu/III group ratio in and the thickness of the metal precursor film by the use of ICP (inductively coupled plasma) analysis. A maximum conversion efficiency of 12.93% and a reproducibility of 85% were achieved, which meant that the production cost goal was achieved. In the effort to develop a high-resistance buffer layer fabrication technology, a fabrication method was developed in which a lower limit was specified for solution transparency enabling the completion of the film fabrication process with no colloid formation occurring in the solution. For preventing the high-resistance buffer layer fabrication process from growing too complicated, the steps were integrated into one for the MOCVD-ZnO:B window layer. As the result, the film fabrication process subject to the film fabrication control based on solution transparency was simplified for a great increase in reproducibility. (NEDO)

Development of GE90 engine with largest thrust. GE90 engine no kaihatsu jokyo

Energy Technology Data Exchange (ETDEWEB)

Aono, H [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

1994-05-01

The present paper explained the turbofan engine GE90 which is being developed by General Electric Co., USA. That engine is to meet the thrust (takeoff thrust) of 300 to 530kN as required for the new-generation wide-fuselage civil transport plane which is being designed for its planned operation in the 1990's. In April, 1991, the world's strongest thrust of 480kN was achieved with engine elements also confirmed through element test. Thereafter, the engine underwent a flying test on board of Boeing 747 to materialize the planned operation in 1995. Made to be 9 in by-pass ratio and about 40 in overall pressure ratio, the GE90 was given the concept that advantage could be secured in both propulsive efficiency and thermal efficiency. That concept could be materialized by the development of composite fan blade technology and energy-efficient technology which were both demonstrated with an unducted fan. In spite of its pressure ratio of 22, the GE90's high pressure compressor demonstrates its polytropic efficiency which is equal to that of the low pressure ratio compressor. 3 refs., 19 figs., 1 tab.

Development of position measuring technology by GPS; GPS ni yoru sokui gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Ishizaki, T [Ministry of Transportation, Tokyo (Japan)

1994-07-25

With regard to the GPS (global positioning system) which uses the satellites launched and administered by the U.S.A. and has been utilized worldwide for ships, automobiles and geodetic surveys in recent years, Ministry of Transport started investigation and research on the application of its position measuring system from FY 1989. In this fiscal year, a study on position measuring methods and selection of the position measuring system to be developed were made, in FY 1991, the real-time functioning and track display were developed, in FY 1992, the initialization aboard the ship, the measure to prevent cycle slip, and the radio data communication technology were developed, and in FY 1993, a long term demonstration experiment presuming its practical use was conducted attaining the expected purpose. In this article, the developed real-time kinematic position measuring system is introduced. Regarding the position measuring methods by the GPS, there are the one point position measuring method and the relative position measuring method. Regarding this newly developed position measuring device, its application to work ships and structures can be considered in various ways. 4 figs.

Development of a method to maintain vigilance level; Kakusei teika keigen shuho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Okamoto, Y.; Horiguchi, A.; Ishida, K.; Hata, S. [Mazda Motor Corp., Hiroshima (Japan)

1995-04-20

As a part of measures to prevent accidents caused by reduced vigilance and drowsiness of drivers, this paper reports the result of experiments that presents effectiveness of a method to give drivers intermittent auditory stimuli as environmental stimulation. It was found that vigilance decline can be reduced by intermittent auditory stimuli under a laboratory condition using a selective reaction time in monotonous selective reaction works as a parameter; and the effective interval in the intermittence is 30 seconds. A driving simulator was used to prove that the vigilance decline reducing effect by the intermittent auditory stimuli has the same level of effect as chewing gums even under the environment composed of driving operation, vehicle motions, and background noise. However, a number of questions remain yet to be discussed, such as the effect when the ratio of sound presentation time and no presentation time was varied. Furthermore, a number of other physical stimuli in addition to auditory stimulation may be assumed that has effective possibility as vigilance decline reducing stimuli, including hot heat and vibration. It was verified, however, that vigilance decline can be reduced by properly varying the environmental stimulation. 6 refs., 15 figs., 1 tab.

Both hydrogen and electricity chargeable battery; Suiso to denki de juden kanona denchi kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-01

Kuriyama group of the Osaka Industrial Research Institute developed a new air-metallic hydride battery that is chargeable by both electricity and hydrogen gas. The battery uses a hydrogen storage alloy as the negative pole and uses active carbon coated with platinum as the positive pole. Potassium hydroxide aqueous solution is used as the electrolyte, and a space is arranged in the negative pole for contacting and absorbing the hydrogen with a good efficiency. The key point is the development of the hydride for energy storage that can well absorbs the hydrogen gas even it is dampened by the electrolyte. And the pole is prepared by pulverized the particles of rare earth hydrogen storage alloy having the particle size smaller than 150 micron meter, forming a Ni layer for a catalyst to absorb hydrogen, adding fluorinated resin dispersant for the sake of repellency and forming a sheet. In a test running, a half of hydrogen storage capacity is realized by charging for 30 minutes. And, 0.6 V electricity of 10 mA per unit pole area of 1cm{sup 2} is continuously obtained for 17 hours during discharging. While a third electrode is formed by nickel hydroxide, the battery is chargeable and dischargeable as the same as nickel hydrogen battery. Low cost and small size can be expected by a combination of respectively prepared fuel battery with nickel hydrogen battery. (translated by NEDO)

Radar system for non-excavation flowmole drilling; Flowmole koho zenpo kanshi sensor no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Nakauchi, T; Hayakawa, H; Tsunasaki, M; Kishi, M [Osaka Gas Co. Ltd., Osaka (Japan)

1997-10-22

Technology is discussed of detecting structures buried in the ground by use of a forward-looking sensor mounted on the drill head for the avoidance of collision with such structures during application of the flowmole method in urban districts. In this detection system, pulsating radio signals are emitted from a transmission antenna and the received signals are converted into low-frequency signals in a sampling circuit for eventual display on a B-scope. Since the drill head for flowmole technology is as small as approximately 50-60mm in diameter, experiment is conducted to know the detectability of a very small antenna directed at a buried pipe. The basic phase of the experiment using the very small antenna includes a soil-filled tank test and field test. It is then found that the very small antenna is capable of detecting the steel pipe buried 50cm away from the antenna with the antenna directed at the said pipe. In a test wherein a very small antenna is allowed to rotate on the drill propelling shaft, the design simulating a revolving drill head, it is learned that the detecting system under study will identify the direction in which a buried structure exists. 1 ref., 9 figs.

Research and development project plans for FY 1995; 1995 nendo kenkyu kaihatsu jigyo keikaku

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-01

The present research and development project plans for FY 1995 administrated by NEDO consist of research and development of new energy, and research and development of industrial technology. Are illustrated further enhancement of new energy introduction promotion measures, new stage of international projects, promotion of new energy and new energy technology development, further enhancement of industrial and scientific technology research and development, integrated measures against global and urban environment problems, and budget of NEDO projects in FY 1995. The research and development of new energy includes coal conversion technology, solar energy technology, geothermal energy technology, energy conversion and storage technology, hydrogen, alcohol and biomass energy technology, geothermal energy resources, coal resources development, new energy promotion department activities, NEDO information center activities, and so on. On the other hand, the research and development of industrial technology includes research and development of industrial technology, and global environment technology. The research and development of industrial technology consists of superconductivity, new materials, biotechnology, electronics, information and communications, machinery and aerospace, natural resources, humanity, life and society, and various leading researches.

Development of RaRaII solar car. Solar car RaRaII no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Ohashi, M [Toyota Motor Corp., Aichi (Japan)

1991-05-31

A solar car was developed to be able to travel, by utilizing solar energy, as a guiding car for the marathon race in the public road. That car is 210kg in weight, 1 in number of riding persons and 4.8m in smallest rotating radius. Its traveling performance is 44km h in highest speed, 10{degree} in hill-climbing ability and 0.6m s{sup 2} in acceleration. Those principal particulars satisfied the required condition of guiding car for the marathon race. That car was equipped with a polycrystalline silicon type solar cell, 6m{sup 2} in area to generate 870Wp power. A silver oxide-zinc battery, used as a secondary battery to secure traveling in case of rain, is of a performance to travel twice the marathon race road through. To satisfy the public road traveling in safety standard, that car was equipped with head lamps, wiper, direction winkers, rear-view mirrors, etc. As material of the body, aramid fiber and carbon fiber were adopted for securing the rigidity to cover the lightening in weight. That car, as used at an opportunity of intercollegiate marathon relay race, traveled a distance of about 30km which was its entire public road portion of course. 2 figs., 2 tabs.

Development of a robot system for converter relining; Tenro chikuro robot system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Ito, Y; Kurahashi, M [Nissan Motor Co. Ltd., Tokyo (Japan)

1995-09-12

In steelmaking plants, the relining work of converters requires plenty of manpower and time. Recently, the number of expert brick workers has decreased, and it has been difficult to get together the necessary number of workers for the converter relining. To solve these problems, a robot system has been developed and realized for the converter relining. The system consists of two intelligent robots and an automatic brick conveying machine. With visual function and flexibly controlled hands, the robot enables to heap up bricks in the same manner as expert workers do. The automatic brick conveying machine consists of roller conveyers and a cage lifter that convey bricks on palettes to the suitable position for the robot to easily handle. This robot system has enabled to save much labor for the converter relining. 8 figs.

Development of application technology of ultrasonic wave sensor; Choonpa sensor oyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Hosoya, H; Hikita, N; Sasaki, H; Kore, H [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

We have developed parking assist system, which informs a driver the closing point and distance to the objects such as other vehicle, wall and pole around the own vehicle at parking area and makes parking maneuverability easy. This system is based on the range detection technology using ultrasonic wave sensor. We have improved the detecting ability in short range of about 20cm by reducing the reverberation of transmitting wave signal and controlling sensitivities of signal intensity and threshold line. We will show mainly the improvement of short range detection of ultrasonic wave sensor, and briefly the performance of parking assist system. 1 ref., 14 figs., 1 tab.

Development of a platoon driving AHS; AHS jikkensha ni okeru gunsoko seigyo no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Seto, Y; Inoue, H [Nissan Motor Co. Ltd., Tokyo (Japan)

1997-10-01

Nissan and the Public Work Research Institute of the Ministry of Construction are developing an Automated Highway System. We are investigating a longitudinal control system in AHS. In this paper, a vehicle control method using two actuators an engine and a brake, is described. Experimental and simulated results are shown. A Platoon driving control method using road-to-vehicle and vehicle-to-vehicle communication is described. And the influence of the communication on the control performance is shown by experiments and simulation. The effects of the communication device and control device mentioned above are verified by experimental results in an AHS field test conducted in September 1996 on a dosed highway. 5 refs., 8 figs.

Hierarchical functional model for automobile development; Jidosha kaihatsu no tame no kaisogata kino model

Energy Technology Data Exchange (ETDEWEB)

Sumida, S [U-shin Ltd., Tokyo (Japan); Nagamatsu, M; Maruyama, K [Hokkaido Institute of Technology, Sapporo (Japan); Hiramatsu, S [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

A new approach on modeling is put forward in order to compose the virtual prototype which is indispensable for fully computer integrated concurrent development of automobile product. A basic concept of the hierarchical functional model is proposed as the concrete form of this new modeling technology. This model is used mainly for explaining and simulating functions and efficiencies of both the parts and the total product of automobile. All engineers who engage themselves in design and development of automobile can collaborate with one another using this model. Some application examples are shown, and usefulness of this model is demonstrated. 5 refs., 5 figs.

Development of super thin foil metal supported catalyst; Chousuhaku metal tantai shokubai no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Sanji, F; Takada, T [Toyota Motor Corp., Aichi (Japan)

1997-10-01

In order to improve warm-up performance, high heat resistance and long life durability of catalysts, the reduction of the metal support heat capacity has been focused. The effects of both reducing foil thickness and lowering cell density on low heat capacity have been investigated. As a result of engine bench and vehicle test, it was apparent that the reduction of foil thickness has greater effects. Newly developed 30 {mu} m foil thickness metal supported catalyst has quicker warm-up performance, and its structural durability up to 950degC is confirmed. 3 refs., 11 figs., 1 tab.

Development of multiplexing network for air conditioner systems; Eakon yo LAN system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, T; Nakazawa, Y; Nakase, M; Sato, Y [Nissan Motor Co. Ltd., Tokyo (Japan); Nomura, M; Okasato, Y; Sunaga, H [Calsonic Corp., Tokyo (Japan)

1997-10-01

Plural air flap actuators of the air conditioner system in a vehicle have been integrated into a single-type actuator using two newly developed technologies: super-low-cost multiplexing network technology and digital motor control technology with a 1-bit A/D converter. The number of harnesses and connectors and the handling load of the air conditioner control microcomputer are reduced, so that we succeeded in sharply reducing the cost of the air conditioner system. 9 figs., 2 tabs.

Development of roller type side slip tester; Roller shiki side slip tester no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Nishiyama, S [Hiroshima City Industrial Technology Institute, Hiroshima (Japan); Harada, S; Harada, K

1997-10-01

This paper presents a new development of roller type side slip tester (RTSSI). The test equipment consists of four parts, which are developed in this research. These are a roller part, a control part, a remote control part and a CRT part. In this study, we especially investigated the mechanism and performance between tire and roller. We analyzed the amount of side slip with various toe angles. The developed tester is examined under the conditions that is considered in industrial applications. We investigated the influences of toe angle, size of tire, pressure of tire, coefficient of friction between tire and roller, pushing force of tire, revolution velocity of roller, axle load and so on. The validity of the developed RTSST is confirmed under these conditions. It was found that the RTSST can be used in practical use. Some measurement results are presented in the form of parametric plots. And we also compared measurements data between the RTSST and that of flat type using several automobiles. 4 refs., 8 figs., 4 tabs.

CAE for the development of two-wheeled vehicles. Nirinsha kaihatsu no tame no CAE

Energy Technology Data Exchange (ETDEWEB)

Hirose, T. (Suzuki Motor Co. Ltd., Shizuoka (Japan))

1992-11-01

Applications of CAE to the development of two-wheeled vehicles were outlined. The performance estimation program for 4-cycle engines featured by its easy execution was presented illustrating an estimation model and estimated results, and the FEM generator for strength/rigidity analysis CAE indicating analytical examples of a piston and frame which is featured by easy formation of models and easy execution of advanced analyses by beginners. The vibration analysis system to estimate exciting forces from engine specifications and to estimate vibration levels of bodies with FEM models was also presented together with the estimation system of rider's vibration sensitivity. Furthermore, the noise suppression/ exhaust pressure calculation program to support muffler designs by simultaneous calculation was presented together with the thermal flow analysis program featured by easy calculation with more suitable models illustrating the analytical example of thermal flow in a large luggage box. 7 refs., 15 figs.

FY 1998 report on the R and D of the industrial science technology. R and D of synergy ceramics; 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Hazardous ingredients in gases exhausted from diesel, refuse treatment facilities, etc. are becoming the problem. The development is expected of porous ceramic films which have functions of separation/purification at high temperature. By making good use of the technology to synthesize ceramic films with uniform through pores of several ten nm order and the technology to form 1D through pores of several ten - 100{mu} m order, the development of the following technologies were made and are in sight: enhancement of functions of gas separation/purification, function of catalyst-carrying to be given, porous film formation/base material fabrication. For the commercialization of high performance structure use ceramic parts, required is innovation of the production method by which the production cost is reduced without damaging the characteristics. Technologies were used of micro-fine raw materials, rapid sintering, texture assessment, analysis, etc., and study was made of cost reduction in high performance ceramic parts. For energy conservation by reducing the sintering temperature, the following were trially conducted: mechanical ironing, use of low grade raw material, use of superplastic reformation and forging, etc. (NEDO)

Development of free running differential. Development of differential with an actuator and a clutch which disconnects the traction; Free running defu no kaihatsu. Kirippanashi kiko oyobi actuator wo naizoshita differential sochi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Yamazaki, N; Teraoka, M; Ishikawa, O; Nagaoka, T; Ugajin, K [Tochigi Fuji Sangyo Co. Ltd., Tochigi (Japan)

1997-10-01

Free Running Differential has an effect on fuel economy and noise reduction from drive line for four wheel drive vehicle. It has an actuator and a clutch which disconnects the traction from no driving side tire when two wheel drive is selected. this unit can be installed in conventional differential carrier with no design change. It is compact in design and low in cost. We evaluate it as having a dominant position among any other Free running system. 7 figs.

Research and development of basic technologies for the next generation industries, 'three-dimensional circuit elements'. Evaluation on the research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu 'sanjigen kairo soshi'. Kenkyu kaihatsu hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-04-01

Research, development and evaluation were performed with an objective of establishing the basic technology related to three-dimensional circuit elements that integrate functions at ultra-high density. For the basic technology of lamination, the SOI technology suitable for the three-dimensional circuit elements was developed, and it has become possible to manufacture high-quality multi-layered crystalline structure by means of annealing that uses laser and electron beam. In addition, a lateral epitaxial technology for solid phase was developed, and the base to be applied to the three-dimensional circuit elements was established. Furthermore, the technology to put thin film circuits together would be useful for high-density integration in the future. The three-dimensional circuit makes parallel processing in each segment possible, whereas a possibility was shown that the processing can be performed at much higher speed than before. Actually a prototype three-dimensional circuit equipped with functions for parallel processing and judgment processing was fabricated. The image pre-processing which has been impossible on the real time basis in the conventional two-dimensional integrated circuit was realized in a speed as fast as milli-second order. These achievements lead to a belief that the targets for the present research and development have been achieved. (NEDO)

Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (interim report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

Development was made on a technology to evaluate quality of composite materials. Few data are available for environmental resistance of composite materials, whereas identification of environmental deterioration behavior and establishment of a environmental resistance evaluating technology are a significant issue in utilizing these materials as new materials for space, aeronautics, and marine applications in the future. The present research was taken up with objectives to elucidate deterioration behavior of composite materials exposed to special environment in the atmosphere and space and to establish methods for acceleration tests and environmental performance evaluation by using simulated environments equivalent to the natural environment exposure. The former period (fiscal 1982 through 1984) has investigated environmental conditions in the atmosphere and space, prepared standard test specimens, performed design on environmental devices simulating the environmental elements, as well as tests on deterioration due to environmental elements, and systematized the deterioration characteristics to establish composite test conditions. The latter period (fiscal 1985 through 1988) has developed the composite environment testing device based on the result achieved in the former period, elucidated the deterioration behavior under the composite environmental conditions, and performed evaluation tests on the developed composite materials (FRP). (NEDO)

Research and development of a high-temperature superconducting flywheel energy storage system. Research and development of the New Sunshine Program; Furaihoiru denryoku chozo shisutemu kenkyu kaihatsu. Nyu sanshain keikaku ni motozuku kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, Y. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1999-11-25

The project conducted by NEDO for developing a high-temperature superconducting flywheel energy storage system is introduced; the two test results of fundamental studies are described. One is the measurement of levitation force and rotation loss of superconducting magnetic bearings composed of oxide superconducting bulks and permanent magnet composite. Two types of superconducting magnetic bearings. axial and radial types, were fabricated and tested. The other test was the fabrication and testing of two functional models. A small-sized superconducting flywheel model of the 0.5 kWh class was fabricated and tested. A medium-sized rotating functional model of the 10 kWh class was fabricated as well. (author)

Research and development of peripheral technology for photovoltaic power systems. Study of nickel-hydride storage battery for photovoltaic generation systems; Shuhen gijutsu no kenkyu kaihatsu. Taiyoko hatsuden`yo suiso denchi no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on R and D of nickel-hydride storage battery for photovoltaic generation systems in fiscal 1994. (1) On the study on low-cost electrode materials, the physical properties and electrode characteristics were studied of the prototype hydrogen absorbing alloys prepared by substituting Cu or Ni for Co in Mm(Ni-Co-Mn-Al)5 (Mm: mixture of rare earth elements). The result clarified that it is difficult to reduce Co content in the alloy to 0.4 atom or less. Simple heat treatment and milling processes in production of hydrogen absorbing alloy electrodes were achieved by adopting an improved metal mold and gas atomization method. Characteristics and cycle life of the Ni positive electrode prepared by applying active paste material of Ni(OH)2 were studied, however, the result showed only lives of nearly 300 cycles. (2) On the study on electrode structure for high-performance (long-life) battery, the 3-D porous metal electrode support was evaluated, and various battery configurations were studied. 11 figs., 1 tab.

Research and development of basic technologies for next generation industries, 'composite materials'. Evaluation on final research and development (final report); Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Fukugo zairyo (saishu kenkyu kaihatsu hyoka 3)

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-05-01

This paper carries the specifications for advanced composites in the investigation (SACOI), and lists the titles and organizations and persons in charge. The paper describes the specifications for test and measurement methods for each title. The titles are: testing methods of matrix resins for carbon fiber reinforced plastics, measurement method for thermogravimetry and glass transition temperature for the same plastics, measuring methods for specific gravity, fiber and void contents of carbon fiber reinforced plastics, testing methods for tensile properties, compression properties, apparent interlaminar shear strength, tension fatigue, interlaminar fracture toughness, crack propagation, high velocity impact, izod impact, and environmental resistance for the same plastics, evaluation methods for hot-press formability of prepreg, autoclave formability of prepreg for the same plastics, measuring methods for tex count, density, and fiber volume fraction of wire preform, testing methods for tensile strength at room temperature, tensile strength at elevated temperature of wire preform, measuring methods for thermal expansion coefficient, tension properties, compression properties, tensile shear strength, interlaminar shear strength, in-plane shear strength, tensile fatigue, high velocity impact and regular impact of wire preform. (NEDO)

Sunshine Program-assisted project achievement report for fiscal 1981 on the development of technologies for photovoltaic power system practical application. Development of photovoltaic power generation demonstration system (Research and development for schoolhouses); 1981 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden demonstration system kaihatsu (gakkoyo system no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Power generated by solar cells complying with NEDO (New Energy and Industrial Technology Development Organization) specifications is stored in a storage battery or is converted into AC power in a DC-AC converter for interconnection with a commercial power system, and then supplied to loads in schoolhouses. The system operates independently when the commercial power system is out. Basic plans and primary specifications had been determined, basic modules experimentally built, tested, and part of their details designed, all these up to fiscal 1980. In fiscal 1981, system design details are drawn, housetops are examined for installation, and problems that may entail installation are checked. A system data accumulation unit comes into operation for data collection. A system simulator is developed and constructed and the solar cell is checked for performance. Model arrays are built and subjected to a combination tests, when the effect of shade is also investigated. A charge control unit, high-efficiency GTO (gate turned-off) thyristor DC-AC converter, and a protection circuit in preparation for interconnection are developed, and experimentally constructed. In fiscal 1982, 20kW solar cells will be installed and schoolhouse systems will come into service operation. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium R and D. Third year report. R and D of the transversal maintenance technology; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium kenkyu kaihatsu. Odanteki maintenance gijutsu no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of eliminating bad effects of the maintenance/management of equipment/facilities of plants which are made separately and of heightening efficiency of work and improving technology, persons in charge of maintenance/management, persons requesting maintenance/management and official research institutes proceeded as one with the construction of a system doing maintenance/management work. Concretely, three parties cooperated in integration and enhancement of element technologies such as inspection/diagnosis and arrangement/repair and developed the maintenance/management system (maintenance center) which does not specify objects. Based on this system, development was made of the network connecting between the center and facilities, diagnosis car, and multi-functional repair car. Studies were made on the following three. As to the system development, conducted were the development of a deterioration mode prediction system, basic structuring of a remote maintenance network, and making of fatigue/corrosion/abrasion database. Concerning the tool development, technology to foresee damages on the static portion such as piping, etc. were developed. In the study of field application, conducted were analysis of maintenance flow, development of retrieval system of equipment parts/personnel/operation procedures and multi-functional repair car, etc. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Research and development of photovoltaic system evaluation technology (Research and development of system evaluation technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu (system hyoka gijutsu no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In relation with several types of standard photovoltaic power generation systems expected to be put to practical use, design parameters are quantified, databases are utilized, and simulation technologies are developed, while collecting data from test facilities constructed to simulate them, for the development of evaluation techniques indispensable for the efficient improvement of photovoltaic power generation systems. In fiscal 1998, data were collected from verification test facilities and residential photovoltaic systems sited across Japan. The collected data were subjected to analysis and simulation, by which correction factors were calculated for smudge, spectral response, incident radiation, and temperature. Furthermore, load matching factors and storage battery contribution rates were calculated by simulation for the stand-alone photovoltaic systems sited in five Japanese cities, each comprising an array, storage battery, charge/discharge controller, DC-DC converter, and a load. Reference is also made to a survey of trends of technology development. (NEDO)

Report on achievements in technological development in fiscal 1999. Development of technology to put photovoltaic power generation system into practical use (Research and development of high reliability storage batteries for photovoltaic power generation use); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Kenkyu kaihatsu kanri (taiyoko hatsuden'yo chikudenchi kaihatsu bukai)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Storage batteries used in household photovoltaic systems must be free of electrolyte leakage and maintenance, and be readily installable in residential houses. Lead-acid batteries that can meet these requirements and have been put into practical use may include the sealed storage batteries. However, these batteries currently in use have drawbacks in life performance and price. Therefore, development is under way on lead-acid batteries for household photovoltaic systems by improving said sealed lead-acid batteries. The targeted batteries should have as long life as passing 3,000 cycles under a condition of 0.1 to 1 CA discharge (at depth of discharge of 50%), energy density of more than 70 Wh per liter, and cost of 12 yen or lower per watt-hour. A prototype battery as the final candidate was fabricated, that uses silica powder as the electrolyte retainer (silica powder filled between plates, and into clearance between plate groups), pasted plates made of expanded metal grids for positive plates, and micro conductive network plates with increased addition amount of carbon to micro active material (PbO{sub 2}) as negative plates. Life performance testes thereon are being performed. This lead-acid battery is estimated to be capable of satisfying the intended performance based on the result of discussions having been made so far. (NEDO)

FY 1998 Report on development of large-scale wind power generation systems. Feasibility study on development of new technologies for wind power generation (Study on the development of wind power generation); 1998 nendo ogata furyoku hatsuden system kaihatsu. Furyoku hatsuden shingijutsu kaihatsu kanosei chosa (furyoku hatsuden gijutsu ni kansuru kaihatsu doko chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This survey is designed to analyze, e.g., current status of large-scale wind power generation devices/system technologies and development trends worldwide, and to make predictions about future developments, in an effort to contribute to advancements in new technology for wind power generation systems in Japan. The international R and D cooperation programs promoted by IEA and EU have helped the participants produce a number of good results at lower costs. The European countries have developed the wind power generation industries in each area, promoted by the governmental subsidy policies, and are leading the world. The system is becoming larger, from around an average unit capacity of 250kW in the beginning of the 90's to 600kW now, reducing the cost by the scale merit. The improved computer capacity has made it possible to more easily analyze the complicated rotor aerodynamics, structural dynamics, wind characteristics and other factors related to wind power generation systems. The future R and D directions will include world standards for large-scale wind turbines, advancements in wind farm technologies, offshore wind power generation systems, advancement in design technologies, and new concepts for wind power turbine designs, e.g., floating wind turbine. (NEDO)

Fiscal 1997 report on the results of the international standardization R and D. R and D of a mobile office system (R and D of next generation mobile business terminals); 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Mobile office system no kenkyu kaihatsu (jisedai keitai joho kiki no kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This R and D is aimed firstly at trially developing next generation mobile business terminals (MBT) based on the technical standards of MBT of which the standards were completed in the fiscal 1996 R and D of Mobile Office Promotion Association (MOPA), secondly at developing an evaluation method for trial terminals and establishing the technical standards of MBT through data communication among different terminals and confirmation of application motions, and thirdly at promoting the international standardization. The study was conducted in the following procedures: 1) making of a comprehensive examination-standardization working group, determination of the use of trial terminals and the MBT evaluation method; 2) trial development of the MBT standards and prototypes; 3) study of the MBT evaluation method; 4) evaluation test on the prototypes; 5) comprehensive evaluation. As the fruit of the study, the evaluation/test specifications were completed, and the evaluation tests among different terminals were conducted. As a result of the evaluation test, the transplantation of MBT managers was done almost with no problems. The MBT adaptability evaluation test was also done almost without problems. 6 figs., 6 tabs.

FY 1980 Report on results of Sunshine Project. Research and development of coal liquefaction techniques (Development of direct hydrogenation type liquefaction plant and 2.4 T/D test plant); 1980 nendo sekitan ekika gijutsu no kenkyu kaihatsu, chokusetsu suiten ekika plant no kaihatsu seika hokokusho. 2.4T/nichi jikken plant no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This program is aimed at construction and operation of a 2.4 T/D test plant for eventual commercialization of the direct hydrogenation type liquefaction process. The FY 1980 program includes designs of the test plant, procurement and manufacture of some equipment, and works for construction of the bases, buildings and scaffolds. The construction site for the 2.4 T/D plant was changed in July 1980 from Mitsui Engineering and Shipbuilding's Chiba works to NKK's Keihin Steelworks, which was accompanied by some changes in the basic and detailed designs. The detailed designs were reviewed for construction of the test plant, to reflect the results of the individual elementary researches. The works for the FY 1980 program also include preparations for obtaining approvals of plant construction, based on the revised designs, from the related government offices, and equipment procurement. This paper presents the major drawings for the plant construction, including those for PID designs, overall plant layouts, piping systems, buildings, scaffolds, and pipe racks. The loading data are also included. (NEDO)

Achievement report on industrial science and technology research and development in fiscal 2000. Research and development of synergy ceramics (Research and development of technology to prevent corrosion in petroleum production systems); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (sekiyu seisan system fushoku boshi gijutsu kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Achievements in fiscal 2000 were put into order for research and development of synergy ceramics aimed at completion of high temperature energy materials and ultra-precision materials. Activities were taken in the following four areas: 1) materialization technologies and advanced assessment and design technologies, 2) application technologies, 3) common basic technologies, and 4) assessment on composite function manifestation process. In Item 1), discussions were given on ultra-precision materials, high temperature energy materials, member designing basic technologies, materials to detect stress and microfine destruction, pore pattern controlling porous materials, and self-restoration and self-lubrication functioning materials. In Item 2), discussions were given on material and light selection functioning materials, high abrasion resistant and easy-to-process materials, high performance resistance materials for electric power devices, and flexible sliding materials. In the material and light selection functioning materials, their material selecting function was manifested by controlling micro pores through xerogelation on inorganic and organic hybrids. In the assessment of the composite function manifesting process, the wet type forming process was assessed, that uses microfine powder for model parts assuming cut members. (NEDO)

Fiscal 1993 achievement report on New Sunshine Program. Development of photovoltaic power generation system practicalization technology (Development of ultrahigh-efficiency solar cell technology - Development of crystalline compound solar cell technology); 1993 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Chokokoritsu taiyo denchi no gijutsu kaihatsu (kessho kagobutsu taiyo denchi no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Efforts are made to enhance InGaP cell efficiency (target 16%) on a GaAs substrate by prolonging the InGaP minor carrier life span. In preparation of InGaP cell fabrication on silicon, a study is made of epitaxial growth of a wide band gap layer. By improving on the conditions of InGaP heteroepitaxial growth under the MOCVD (metal-organic chemical vapor deposition) method on a GaAs substrate, the InGaP cell base layer minority carrier life span is increased to be longer than 5ns. The use of epitaxial crystals greatly improves on the efficiency of InGaP cells on a GaAs substrate. Furthermore, cell structure improvement and the like are accomplished, which results in the achievement of an efficiency rate of 17.4%. As a basic technology for the fabrication of InGaP/Si tandem cells, experiments are conducted of growing a wide gap layer for the growth of Ln{sub 1-x}Ga{sub x}P on an silicon substrate. For the evaluation of epitaxial crystals and interfaces, time resolution photoluminescence measurement is performed and the result is compared with the result of simulation. (NEDO)

Fiscal 1994 report on technological results. Technological development for putting solar system to practical use such as industrial use / Development of advanced heat process type system / Development of solar thermal refrigeration system; 1994 nendo sangyoyo solar system jitsuyoka gijutsu kaihatsu / Advanced heat process gata system no kaihatsu / Taiyonetsu reito reizo system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

A system is being developed for adjusting incident solar energy in accordance with objectives by using, as a window material, glass whose light transmittance is variable by the electrochromic color and bleach reaction. The target is a module which, having an area of 60x40 cm or larger, is capable of installation for a structural opening of a building, which has a practical service life (ten years outdoors), and which is provided with the range of visible transmittance of 50% or more with capability of continuous light adjustment. In fiscal 1994, a basic parameter was set for the production process of a large module, with the experimental production/evaluation conducted, and with an outlook formed for achieving the target. The device is basically composed of glass, transparent electrically conductive film, counter electrode, electrolyte, principal electrochromic film electrode, transparent conductive film, transparent resin film for sealing, and glass, with the total thickness 4 mm or above. The transparent conductive film in use is tin-based, the counter electrode is NiOx based in oxidation color-erasing type, the electrolyte is Sb{sub 2}O{sub 5}, and the principal electrode is WO{sub 3} based in reduction color-developing type. (NEDO)

Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Development of silicon substrate manufacturing technology for high-quality solar cell); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Kohinshitsu taiyodenchiyou silicon kiban seizo gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for enhancing productivity and energy conservation by rendering continuous and automatic the electromagnetic casting process for manufacturing polycrystalline silicon substrates for solar cells. In the manufacture of ingots for substrates by continuous electromagnetic casting, the chuck type system for feeding power to the melt plasma was replaced by a roller type system, and the power feeding position was moved to the high temperature region. Also, an on-line ingot slicing technique was established. In the manufacture of substrates at a slicing rate of 300 {mu}m/minute, productivity of 115,000 wafers/month, yield of 98%, and thickness tolerance of 30 {mu}m were achieved. A high-speed cleaning technique was developed using a jet stream, by which the cleaning time was reduced to 5 minutes and the slurry recovery rate was elevated to 95%. Based on these, substrate-related costs in the case of 100 MW/year production was calculated, which resulted in a cost of 98.8 yen/wafer (target: 103.3 yen/wafer) for manufacturing 15 cm square substrates from ingots and in a 15 cm square substrate slicing and cleaning cost of 135.1 yen/wafer (target: 135.4 yen/wafer). (NEDO)

Fiscal 1997 survey report. Feasibility study of the environmentally friendly type coal utilization system (feasibility study of the environmentally friendly type coal utilization system in India); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Indo ni okeru kankyo chowagata sekitan riyo system kanosei chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The survey was conducted of the present situation of coal utilization and the present coal situation such as the environmental state of India which is a coal producing/consuming country next to China in Asia. The paper studied a feasibility of the introduction of the environmental friendly type coal utilization system` to be planned in India. The items for survey are the present situation of economy and energy and the future trend, environmental problems on coal utilization, the present status of the coal distribution system and study subjects, the present status of coal utilization by field and study subjects, a possibility of briquette use, a possibility of coal fluidization, electric power development plans and coal combustion technology in each industry, etc. The subjects are the obligation of coal preparation to coal thermal power plants 1000 km away from coal mines starting 2001, measures taken for effective ash use, measures taken for superannuated gas furnaces, etc. Based on the results of these site surveys and reports of the investigation under consignment from CMPDI, the paper studied/analyzed possibilities of introducing the coal utilization system having actual introduction results in Japan to India, and made an investigational report. 39 refs., 12 figs., 56 tabs.

Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in Malaysia and Vietnam; Kankyo chowagata sekitan riyo system kanosei chosa. Malaysia Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This survey arranged the status of coal utilization technology and the status of coal production, supply, etc. in Malaysia and Vietnam, examined/studied coal utilization systems in both countries, and finally assessed feasibility of introducing the environmentally friendly type coal utilization system. As a country of primary energy source which is abundant in crude oil, natural gas, hydroelectric power, coal, etc., Malaysia now depends on crude oil and natural gas for 80% of its energy, and places emphasis on exploration of natural gas and oil refining. In electric power and cement industries where coal is consumed, effectiveness and environmental issues in association with coal utilization are future subjects. In Vietnam, the north is abundant in hydroelectric power and anthracite, and the south in oil and gas resource, but the north and central districts are in a state of undevelopment. Coal is used for coal thermal power generation, cement industry, and residential/commercial fuel. In the future, effective coal utilization and environmental issues will be subjects. 16 refs., 38 figs., 75 tabs.

Fiscal 2000 operation report. Fiscal 2000 model project for promoting advanced utilization of coal (Survey on data control system for advanced utilization of coal in Japan); 2000 nendo sekitan kodo riyo shuishin moderu jigyo gyomu hokokusho. Nihon no sekitan kodo riyo ni kakawaru data kanri system chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of contributing to the drafting of, for example, measures for securing coal resources for Japan and strategies for developing coal utilization technologies from the standpoint of the world climate of the coal supply/demand in the future, database was built concerning coal information such as coal-related supply/demand trend, technological development and utilization status in Japan and foreign countries, with the results of fiscal 2000 reported. In the preparation of related applications, a jump function in the case of pages unregistered with related subjects was added to the coal information retrieval system completed last year, as were a subdividing function of retrieval conditions and a link function to pages of a technical term dictionary. In the arrangement of the database classified by the fields, programs were prepared on 14 tables primarily in relation to supply and demand, with the collection, processing and registration of the data performed. In addition, in order to deal with the clarification of the patent licensing of GIF related technologies, there was developed a graph display program using a general-purpose language, Java. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the technology of accelerated formation of bio-functions (R and D of the technology of creation of novel advanced enzymes); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kasokugata seibutsu kino kochiku gijutsu no kenkyu kaihatsu (shingata kokino koso sosei gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D on creation technique of novel advanced enzymes. In fiscal 1997, a novel mutagenesis technique was developed to obtain more kinds of mutational genes by shuffling between clonal genes as compared with the previous homogeneous recombination. A genotype- and phenotype-linking technology was developed by expressing random motifs (peptide as components of the active site of protein) on bacteria, and by developing a single-motif protein library. Study was made on a selection system for functional molecules of catalytic activities in a gene level, and a selection system for function of signal transduction. Analysis and evaluation study on vitro experimental technology can be efficiently promoted by recognizing the fitness landscape of target protein molecules. As a result, instead of the conventional method which needs several cycles of mutation and screening of 3-4 week/cycle, an efficient method possible to obtain multiple mutants was established. Research work was also promoted by various organizations to develop an accelerated formation technology of bio-functions. 68 refs., 51 figs., 14 tabs.

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to improve cell efficiency, experiments were conducted for enhancing bottom a-SiGe cell efficiency for the embodiment of an enhanced-efficiency multi-junction cell, for improving crystallinity in microcrystalline silicon through the application of VHF (very high frequency) plasma CVD (chemical vapor deposition), for texturizing metal electrodes on a film substrate, and so forth. In the effort to increase the film fabrication rate, a VHF plasma CVD device was used for studying the effect of the discharge frequency on film deposition and quality, Vpp between the electrodes, and so forth. Studies about the high-throughput production technology centered on the film substrate solar cell process technology and the designing of an optimum geometrical pattern for SCAF (series-connection through apertures formed on film) cells. Production cost was estimated for the SCAF structure film substrate solar cell manufacturing process, and a production cost of 147.1 yen/W (in case of 100 MW/year production) was obtained as achievable under the currently available conditions. (NEDO)

Achievement report for fiscal 2000 on research and development of key technologies for superconducting generator. Research and development of key technologies to increase density, research and development of key technologies to increase capacity, research and development of design technologies, and research of technologies; 2000 nendo chodendo hatsudenki kiban gijutsu kenkyu kaihatsu seika hokokusho. Komitsudoka kiban gijutsu no kenkyu kaihatsu / daiyoryoka kiban gijutsu no kenkyu kaihatsu / sekkei gijutsu no kenkyu kaihatsu / gijutsu chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Researches have been made to increase density of 200,000-kW class generator and to increase capacity of 600,000-kW class generator necessary for putting superconducting generator into practical use. This paper summarizes the achievements in fiscal 2000. In the study of increasing densities of superconductors and field windings, strands were fabricated, in which aging heat treatment conditions, number of aging, and processing degrees between each aging were varied, to increase the critical current of Nb-Ti strand, wherein as high critical current as corresponding to about 90% of the target was obtained. Possibility of increasing the critical current with the final processing degree in the range of 4 to 5 was verified from the relationship between the final processing degree and the critical current. In the study of increasing capacities of superconductors and field windings, findings were acquired on enhancement of conductor stability and reduction in AC loss, with regard to superconductor strands well balanced in the two elements. Prospects were obtained in achieving the AC loss of 200 kW/m{sup 3} in the targeted superconductor. The residual resistance ratio was found to be 200, showing sufficiently high value, and sufficient function was verified in the stabilized copper. In the research of design technologies, primary basic design was performed. (NEDO)

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to develop high-performance solar cells, optimum device designs including an advanced light confinement structure or the like were studied, and a 25% reduction in the total power generation layer thickness and a 7% increase in efficiency in power generation were consistently achieved in an a-Si/a-SiGe solar cell. In the effort to develop low-cost process technologies, as the result of studies involving the optimization of high-speed film fabrication requirements such as hydrogen dilution and a high-speed/high-precision patterning method and the like, an initial conversion efficiency of 11.2% was attained, which was the world high for a 90 cm times 90 cm-large a-Si/a-SiGe solar cell. This being equivalent to a post-stabilization efficiency of 10%, the fiscal 2000 target was achieved. A solar cell module production cost assessment was performed based on the result, and a module cost of 133 yen/W (in case of 100 MW/year production) was realized, which again meant the achievement of the fiscal 2000 target. (NEDO)

FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for production of thin-film solar cells and low-cost, large-area modules (Development of technologies for high-reliability CdTe solar cell modules); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The research and development project is implemented for production of low-cost, large-area modules of CdTe solar cells by the high-quality film-making process and high-function patterning, and the FY 1999 results are reported. The research program for the large-area TCO film-making technologies involves investigations on improvement of SnO{sub 2} film quality by the mist method and continuous film-making, which lead to continuous, stable production of 34 substrates of low resistance of 9.7{omega} on the average. The program for production of the large-area, thin-film CdS/CdTe solar cells involves production of TCO and CdS by the mist method, and patterning of the laminated TCO/CdS film by laser scribing. The CdTe film is formed by the atmospheric pressure CSS method, and treated with CdCl{sub 2} to improve its crystallinity. The CdTe film is patterned by sand blasting, and provided with the carbon and silver electrodes by screen printing, to complete the cell. The process is totally effected at the atmospheric pressure, needing no vacuum device. The CdTe solar cell assembly (130 cells connected in series, opening area: 5,413cm{sup 2}), fabricated on a trial basis, achieves a conversion efficiency of 10%. (NEDO)

Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of low-cost and large-area module manufacturing technologies, and new type amorphous solar cell manufacturing technologies); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (tei cost daimenseki module seizo gijutsu kaihatsu (shingata amorphous taiyo denchi module no seizo gijutsu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to put amorphous solar cells for power use into practical use, research and development has been performed on a low-cost mass production technology for modules with large area and less deterioration using film substrates. This paper summarizes the achievements in fiscal 1999. In developing an efficiency enhancing technology, development of an a-Si/a-SiGe/a-SiGe triple cell structure was launched, and discussions were given on band gaps, film forming conditions, and film thickness. In developing a film forming speed enhancing technology, systematic experiments were performed, as well as theoretical analysis on the film forming mechanism in the plasma CVD process. In developing the process technology for film substrate solar cells, with regard to an a-Si production device of the multi-chamber arranged stepping roll system, six plasma CVD chambers were increased to 13 chambers to improve the electrode forming speed and such processes as drilling low-cost substrates, and laser patterning. In trial fabrication of a triple cell, a module in which one row of the SCAF cell is laminated provided an initial efficiency of 9.64%. (NEDO)

Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture next-generation thin film solar cells, development of technologies to manufacture CIS solar cell modules, development of technologies to increase high-quality film area; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu, CIS taiyo denchi module no seizo gijutsu kaihatsu, kohinshitsumaku no daimensekika gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With an objective to improve efficiency and reduce cost of CIS-based thin film solar cells, research and development has been made on technologies to increase high-quality CIS film area and technologies to increase speed in the manufacturing process. This paper describes the achievements attained during fiscal 1997. The research covered development of technologies to form high-grade Cu (In, Ga) Se{sub 2} (CIGS) film by using the multi-dimensional deposition process, component technologies for forming a rear electrode, a buffer layer and a transparent electrode, and patterning technologies. As a result of the research, thickness of the CIGS film was reduced to half as much as that of the conventional films, having achieved conversion efficiency of 13.1%, which corresponds to about 90% of the conventional CIGS solar cells. In addition, elucidation was made on the effect of an MoSe{sub 2} layer existing on interface with CIGS/Mo in a CIGS solar cell imposed on solar cell characteristics. In developing an Mo film laser scribing technology, intensity dependence of laser energy was made clear, the energy being required for scribing according to surface condition of the Mo film. (NEDO)

Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of new software structuring models (R and D of micromachine cooperative control use software); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Shin software kozoka model no kenkyu kaihatsu (bisho kikai kyocho seigyoyo software no kenkyu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A R and D was conducted of software structuring models which ease the development and maintenance of software systems and meet diversification of needs. As for the study of the cooperative control use programming language, a R and D of agent oriented language Flage was carried out for expansion of language function, arrangement of network function, development of exercises, etc. As to the formulation of agent knowledge, proposed were processes to make a program from the specifications, and EVA, a mechanism in response to changes in the specifications of existing programs. In relation to the basic theory of cooperation system, a study was made mainly of object oriented attribute grammar OOAG as a model representing cooperative computation in software process as a rule group. Concerning the study of the situation recognition mechanism, researched were models of communication and reasoning among agents in cooperation. 187 refs., 107 figs., 23 tabs.

Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell and of low-cost/large-area module (Manufacture of high-reliability CdTe solar module); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (koshinraisei CdTe taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The target is a low-cost CdS/CdTe solar cell of a large area (60cm times 90cm), the establishment of mass-production technologies for the cell, and the enhancement of production efficiency. A thin film formation technology of subjecting CdS film organic metal to pyrolysis is established, which reduces photoabsorption loss in the shortwave domain of wavelength of not longer than 500nm, reduces reflection loss in the film, and improves on short-circuit current density. Improvement is also achieved on CdTe film quality and junction quality by use of a proximity sublimation method in a vacuum, when a conversion rate of 16.0% (1cm{sup 2}) is attained which is the highest in the world. Based on the results of the above-said efforts, a 3.3mm-thick glass substrate is employed for CdTe film to develop into a 30cm times 60cm-large size, with the film thereon uniformly thick over a large area thanks to a normal pressure proximity sublimation method. Studies are made toward a process nearer to the ultimate product and, using the patterning technique, a 30cm times 60cm-large CdTe solar cell is tentatively built realizing a conversion rate of 9.8%. (NEDO)

Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of amorphous silicon-based high-quality material/substrate manufacturing technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu - amorphous silicon kei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The project aims to enhance the stability of amorphous solar cells. For elevating TCO (transparent conductive oxide) substrate transmittance to an ultrahigh level and for obtaining amorphous layers less to suffer photodegradation, efforts were made to develop substrate materials stable upon exposure to plasma and low in defect density. In the study of TCO, a high-transmittance glass substrate was employed and TCO was made thinner, and the specimen achieved transmittance of 91.3% or 6.3% over that of the conventional type. In the study of low reflection films, it was found that their transmittance came to be stable and remain so after 150 days after a weatherproof test. In the study for stability enhancement, optimization was carried out for a plasma resisting Ga{sub 2}O{sub 3}-added ZnO film for the manufacture of a substrate material capable of properly behaving in a high-speed a-Si film fabrication process. Low-temperature film fabrication was studied to enable low-cost manufacturing, and it was learned that a 4 times 10{sup -4} ohm/cm low-resistance film was obtained by sputtering Ga{sub 2}O{sub 3}-added ZnO where magnetism was intensive at room temperature, that films excellent in crystallinity were obtained by the same method even at low temperatures, and so forth. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (R and D of the formation of advanced materials for power generation environment); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Ten nanoscale Ge islands were successfully formed in proper positions on an Si substrate surface by using mask technology of nanoscale atomic layers. Growth of less-defect ZnSe films on a GaAs(110) surface was possible under various conditions. The magnetic transfer mechanism of Mn oxide with huge reluctance was clarified. Through study on selective-area deposition of Si on plasma-oxidized ultrathin SiO2 mask layers patterned by direct electron-beam exposure and an idea of SiO2/SiNx bilayer mask, direct use of the ultrathin mask layer as insulating layer in device structure was achieved. The superior property as electron beam resist of methano- fullerene composed of fullerene C60 with side chains including oxygen was clarified. The initial oxidation process of an Si(100) surface was analyzed, and the observation result by SREM was theoretically explained. Development of a high-resolution spin polarization electron microscope was also mentioned. 48 refs., 145 figs., 20 tabs.

Fiscal 1997 result of the R and D project of industrial science and technology under consignment from NEDO. R and D of creation technology of original advanced materials (R and D of creation technology of original advanced materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo (Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku). Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of creation technology of original advanced materials in the R and D project of industrial science and technology. Although new material technology is dependent on the needs of a future society, it should correspond to a global environment preservation society, information-oriented society and aging society as observed based on the present social trend, and new materials superior in hot strength, light weight, corrosion resistance, decomposability, photo-function, magnetism, conductivity, bio-copying and adaptability are demanded. This project is in promotion since fiscal 1996 to develop formation technology of high-performance advanced new materials by precise molecular control of structure and production process of organic polymers and molecular assemblies. The research started on 4 themes such as advanced stimulus-response material, precision catalytic polymerization, condensed system structure control and multi-dimensional polymer structure. The research on molecule harmonizing material was added in fiscal 1997. In fiscal 1997, the general committee discussed a progress situation and next year research plan, and surveyed an overseas technology trend. 1 fig.

Report on results for fiscal 1996 on development of superconducting electric power application technology. Pt. 2. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 2. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

In fiscal 1996, the initial cooling test and rotary excitation test were conducted for the 70,000kW slow-response type model machine, with the basic characteristics of the rotor verified such as the cooling characteristics, shaft vibration characteristics, mechanical strength, and superconductivity stability, and with the results of the studies explained. The rotor of the 70,000kW slow-response type model was installed in the test site, and the field test was carried out in 1997. For this purpose, research test was performed by the element technology of the model machine and the partial model. The technological development items, trial manufacture and test items were field winding, multi cylindrical rotor and damper. Upon the test results using the element and partial model, the design and manufacturing were implemented of the superconducting generator of a slow-response type excitation method with the output of 70,000kW class. Performed were the basic characteristic test, long-term operation test and severity test on the assumption of abnormality, verifying the characteristics and reliability of the generator as well as obtaining data concerning an excessive electromagnetic force and heat generation. From the test data and the analysis/evaluation results obtained on the model machine, the 200,000kW class pilot machine was reviewed in the conceptual design. (NEDO)

Report on results for fiscal 1997 on development of superconducting electric power application technology. Pt. 1. R and D of superconducting wire, R and D of superconducting generator, studies on total system, R and D of refrigeration system, and verification test; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. 1. Chodendo senzai no kenkyu kaihatsu, chodendo hatsudenki no kenkyu kaihatsu, total system no kenkyu, reito system no kenkyu kaihatsu, jissho shiken

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

This report explains the outline as Part 1. In fiscal 1997, the 10th year of the project, a multi cylindrical rotary model for which an in-situ verification test was finished was brought back to the plant and dismantled for examination, while the in-situ verification test of a slow-response type model machine rotor was conducted in combination with a refrigeration system. In addition, in the research of AC wire materials and oxide based materials, studies were made with a purpose of high characterization and long wire materialization. In the metallic materials, a 10kANbTi conductor was developed while, in oxide-based materials, research was done on performance improvement and wire materialization based on various synthesizing methods. The manufacturing, factory test and in-situ text were conducted for a 70,000kW model machine with the purpose of R and D of a 200,000kW class pilot machine. Examination was made on the test method of the 70,000kW class model machine, operation technology of a superconducting generation system, and the effect of introducing the superconducting generator into a power system. In the conventional refrigeration system, a single unit test was carried out for the liquefaction, liquid storing capacity, etc., of the system. The 70,000kW class model machine was put through a test for confirming the general operation including the refrigeration system. (NEDO)

FY 1999 Report on results of development of high-efficiency energy system technologies for transportation and domestic use. R and D of polymer electrolyte fuel cells, power system technologies, and several kW class domestic power systems operating at normal pressure; 1999 nendo un'yu minseiyo kokoritsu energy system gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, joatsu sadogata su kW kyu kateiyo dengen system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Described herein are the FY 1999 results of the research and development project aimed at development of fuel cell systems for power source systems suitable for domestic use. The programs for development of fuel cell body include improvement of the anode forming method for increasing its CO tolerance, enhancing cell performance at 0.5mg-metal/cm{sup 2} as the catalyst quantity to a level almost comparable to that obtainable at 0.9mg-metal/cm{sup 2}. The programs for development of the fuel supply system include studies on endurance of the elements, e.g., starting-up/shutting-down of the Ru/Al{sub 2}O{sub 3} catalyst, using a microreactor, confirming that it is serviceable for at least 1,000 hours. The natural gas reformer is developed and operated, on a trial basis, achieving stable supply of steam and fuel, and thermal efficiency of 82.7%. The operation researches include development and operation of a 1kW class module, achieving the performance surpassing the FY 1999 targets (average cell voltage: 0.70V, output: 1.27kW) with a simulated reformate gas at an air utilization rate of 20% and current density of 0.3A/cm{sup 2}. (NEDO)

Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of low-cost/large-area module manufacturing technology - Development of novel amorphous solar cell module manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / tei cost daimenseki module seizo gijutsu kaihatsu (shingata amorphous taiyo denchi module no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project intends to improve on large-area amorphous silicon solar cell performance and to develop high-throughput manufacturing technologies for a reduction in the cost of modules. A film substrate type amorphous solar cell structure of the serial connection type named SCAF (series-connection through apertures formed on film) is contrived. Under this method, film formation using a stepping roll system newly developed for glass substrates may be applied, and the number of manhours required is allowed to be less than under conventional serial connection forming processes. The new technique is characterized in that serial connections are established via through-holes provided in plastic substrates. Making use of the technology, progress is attained in the development of high-throughput process technology for film substrate type amorphous solar cells and of efficiency enhancement technology. In fiscal 1997, an electron beam unit for plasma generation aiming at the elucidation of reaction processes in plasma was introduced, and technologies based on the equilibrium discharge technique were developed enabling high-speed a-Si film formation without degradation in film quality. The effect of trace boron addition to the tandem cell bottom I layer was investigated, and a stabilization rate of 8.05% was achieved using a 40cm times 80cm large SCAF cell. In fiscal 1998, endeavors were exerted for similar developments. (NEDO)