WorldWideScience

Sample records for sandy organogenic limestone

  1. Replacement of Eocene white sandy limestone in historical buildings : over 100 years of practice in the Netherlands

    NARCIS (Netherlands)

    Quist, W.J.; Nijland, T.G.; Hees, R.P.J. van

    2013-01-01

    This paper discusses the replacement of white sandy limestone (Gobertange and Lede or Balegem) in the Netherlands in (successive) restorations from the mid-19th century onwards. White sandy limestone, transported from the southern part of the Low Countries (now Belgium), was extensively used in the

  2. Vertical small scale variations of sorption and mineralization of three herbicides in subsurface limestone and sandy aquifer

    DEFF Research Database (Denmark)

    Janniche, Gry Sander; Mouvet, C.; Albrechtsen, Hans-Jørgen

    2011-01-01

    , France. From two intact core drills, four heterogenic limestone sections were collected from 4.50-26.40 m below surface (mbs) and divided into 12 sub-samples of 8-25 cm length, and one sandy aquifer section from 19.20-19.53 m depth divided into 7 sub-samples of 4-5 cm length. In the sandy aquifer section...... showed that a 30 cm active layer with the measured sorption and mineralization values hardly impacted the fate of the investigated herbicides, whereas a total thickness of layers of 1 m would substantially increase natural attenuation....

  3. Vertical small scale variations of sorption and mineralization of three herbicides in subsurface limestone and sandy aquifer

    Science.gov (United States)

    Janniche, G. S.; Mouvet, C.; Albrechtsen, H.-J.

    2011-04-01

    Vertical variation in sorption and mineralization potential of mecoprop (MCPP), isoproturon and acetochlor were investigated at low concentrations (μg-range) at the cm-scale in unsaturated sub-surface limestone samples and saturated sandy aquifer samples from an agricultural catchment in Brévilles, France. From two intact core drills, four heterogenic limestone sections were collected from 4.50 to 26.40 m below surface (mbs) and divided into 12 sub-samples of 8-25 cm length, and one sandy aquifer section from 19.20 to 19.53 m depth divided into 7 sub-samples of 4-5 cm length. In the sandy aquifer section acetochlor and isoproturon sorption increased substantially with depth; in average 78% (acetochlor) and 61% (isoproturon) per 5 cm. Also the number of acetochlor and isoproturon degraders (most-probable-number) was higher in the bottom half of the aquifer section (93-> 16 000/g) than in the upper half (4-71/g). One 50 cm long limestone section with a distinct shift in color showed a clear shift in mineralization, number of degraders and sorption: In the two brown, uppermost samples, up to 31% mecoprop and up to 9% isoproturon was mineralized during 231 days, the numbers of mecoprop and isoproturon degraders were 1300 to > 16 000/g, and the sorption of both isoproturon and acetochlor was more than three times higher, compared to the two deeper, grayish samples just below where mineralization (≤ 4%) and numbers of degraders (1-520/g) were low for all three herbicides. In both unsaturated limestone and sandy aquifer, variations and even distinct shifts in both mineralization, number of specific degraders and sorption were seen within just 4-15 cm of vertical distance. A simple conceptual model of herbicides leaching to groundwater through a 10 m unsaturated limestone was established, and calculations showed that a 30 cm active layer with the measured sorption and mineralization values hardly impacted the fate of the investigated herbicides, whereas a total

  4. Analysis of organogenic competence of cotyledons of Jatropha ...

    African Journals Online (AJOL)

    Analysis of organogenic competence of cotyledons of Jatropha curcas and their in vitro histological behavior. ARC Nogueira, AA Soares, AB Ibrahim, FAP Campos. Abstract. Using cut pieces cotyledons from germinating zygotic embryos of Jatropha curcas, we monitored the series of anatomical events leading to the ...

  5. Assessment of genetic and epigenetic variation in hop plants regenerated from sequential subcultures of organogenic calli.

    Science.gov (United States)

    Peredo, Elena L; Revilla, M Angeles; Arroyo-García, Rosa

    2006-10-01

    Organogenic calli induced from internodal segments were subcultured three times. Regenerated plants obtained from each subculture were analysed by molecular methods. No major genetic rearrangements were detected in the callus-derived plants since none of the amplified fragment-length polymorphism (AFLP) loci were found to be polymorphic. However, epigenetic changes due to a demethylation process were detected by methylation-sensitive amplified polymorphism (MSAP) technique. The results allowed inference of the possible relationship among the plants derived from different calli subcultures and the in vitro control. The plants recovered from the first and second callus subcultures clustered with the in vitro control pools in the phenogram while the regenerants from the third callus subculture showed the highest genetic distance with the controls. This is the first study reporting data about the genetic stability of callus-derived Humulus lupulus L. plants.

  6. Acidification of sandy grasslands - consequences for plant diversity

    DEFF Research Database (Denmark)

    Olsson, Pål Axel; Mårtensson, Linda-Maria; Bruun, Hans Henrik

    2009-01-01

    soil; a number of nationally red-listed species showed a similar pattern. Plant species diversity and number of red-listed species increased with slope. Where the topsoil had been acidified, limestone was rarely present above a depth of 30 cm. The presence of limestone restricts the availability......Questions: (1) Does soil acidification in calcareous sandy grasslands lead to loss of plant diversity? (2) What is the relationship between the soil content of lime and the plant availability of mineral nitrogen (N) and phosphorus (P) in sandy grasslands? Location: Sandy glaciofluvial deposits......). Environmental variables were recorded at each plot, and soil samples were analysed for exchangeable P and N, as well as limestone content and pH. Data were analysed with regression analysis and canonical correspondence analysis. Results: Plant species richness was highest on weakly acid to slightly alkaline...

  7. Fate of herbicides in deep subsurface limestone and sandy aquifers

    DEFF Research Database (Denmark)

    Janniche, Gry Sander

    afgørende for at vurdere herbiciders skæbne i underjord og grundvandsmagasiner. PhD-projektet har undersøgt sorption og nedbrydning af fire model-herbicider (atrazin, acetochlor, mecoprop og isoproturon) i kalksten og sandede grundvands¬magasiner. Desuden er den rumlige småskala-variation af herbicidernes...... tydelig selv inden for få cm afstand over dybden, og betydningen af denne variation afhænger af den samlede udbredelse af lag med forhøjet sorption eller nedbrydning; 2) at kalk/kalksten yder ringe beskyttelse mod grundvands¬forurening med mecoprop, atrazin, isoproturon og acetochlor, da sorptionen er lav...... og mineraliseringen meget langsom for isoproturon, acetochlor og mecoprop, og atrazin ikke er nedbrydeligt; 3) at i sandede grundvands¬magasiner er sorptionen af de fire herbicider generelt lav, men kan under reducerede forhold være kraftig for især isoproturon og acetochlor. Mecoprop, isoproturon og...

  8. Organogenic nodule formation in hop: a tool to study morphogenesis in plants with biotechnological and medicinal applications.

    Science.gov (United States)

    Fortes, Ana M; Santos, Filipa; Pais, Maria S

    2010-01-01

    The usage of Humulus lupulus for brewing increased the demand for high-quality plant material. Simultaneously, hop has been used in traditional medicine and recently recognized with anticancer and anti-infective properties. Tissue culture techniques have been reported for a wide range of species, and open the prospect for propagation of disease-free, genetically uniform and massive amounts of plants in vitro. Moreover, the development of large-scale culture methods using bioreactors enables the industrial production of secondary metabolites. Reliable and efficient tissue culture protocol for shoot regeneration through organogenic nodule formation was established for hop. The present review describes the histological, and biochemical changes occurring during this morphogenic process, together with an analysis of transcriptional and metabolic profiles. We also discuss the existence of common molecular factors among three different morphogenic processes: organogenic nodules and somatic embryogenesis, which strictly speaking depend exclusively on intrinsic developmental reprogramming, and legume nitrogen-fixing root nodules, which arises in response to symbiosis. The review of the key factors that participate in hop nodule organogenesis and the comparison with other morphogenic processes may have merit as a study presenting recent advances in complex molecular networks occurring during morphogenesis and together, these provide a rich framework for biotechnology applications.

  9. Direct Sulfation of Limestone

    DEFF Research Database (Denmark)

    Hu, Guilin; Dam-Johansen, Kim; Wedel, Stig

    2007-01-01

    The direct sulfation of limestone was studied in a laboratory fixed-bed reactor. It is found that the direct sulfation of limestone involves nucleation and crystal grain growth of the solid product (anhydrite). At 823 K and at low-conversions (less than about 0.5 %), the influences of SO2, O-2...... and CO2 on the direct sulfation of limestone corresponds to apparent reaction orders of about 0.2, 0.2 and -0.5, respectively. Water is observed to promote the sulfation reaction and increase the apparent reaction orders of SO2 and O-2. The influence of O-2 at high O-2 concentrations (> about 15...... %) becomes negligible. In the temperature interval from 723 K to 973 K, an apparent activation energy of about 104 kJ/mol is observed for the direct sulfation of limestone. At low temperatures and low conversions, the sulfation process is most likely under mixed control by chemical reaction and solid...

  10. Determination of the minimal inhibitory concentration of Ammonium glufosinate in organogenic calli of Phaseolus vulgaris cv. `CIAP 7247F'

    OpenAIRE

    Idalmis Bermúdez-Caraballoso; Raúl Collado; Lourdes R. García; Novisel Veitía; Amanda Martirena; Damaris Torres; Carlos Romero; Gert Angenon

    2012-01-01

    An efficient selection system is necessary for distinguishing transformed cells of the untransformed tissue. This study aimed to determine the minimum inhibitory concentration of the herbicide Ammonium glufosinate in organogenic calli of Phaseolus vulgaris cv. CIAP 7247F, to use it as a selective agent in the process of genetic transformation. Fragments (4-5 mm) of proliferated calli after second subculture were used as explant. Callus proliferation medium with different concentrations of Amm...

  11. Microseisms from Superstorm Sandy

    Science.gov (United States)

    Sufri, Oner; Koper, Keith D.; Burlacu, Relu; de Foy, Benjamin

    2014-09-01

    We analyzed and visualized the microseisms generated by Superstorm Sandy as recorded by the Earthscope Transportable Array (TA) during late October through early November of 2012. We applied continuous, frequency-dependent polarization analysis to the data and were able to track the course of Sandy as it approached the Florida coastline and, later, the northeastern coast of the U.S. The energy level of Sandy was roughly comparable to the background microseism level generated by wave-wave interactions in the North Atlantic and North Pacific oceans. The maximum microseismic power and degree of polarization were observed across the TA when Sandy sharply changed its direction to the west-northwest (specifically, towards Long Island, New York) on October 29. The westward turn also briefly changed the dominant microseism period from 5 s to 8 s. We identified three other microseismic source regions during the 18 day observation period. In particular, peak-splitting in the double frequency band and the orientation of the 5 s and 8 s polarization vectors revealed two contemporaneous microseism sources, one in the North Atlantic and one in the Northeast Pacific, for the dates of November 3-4. Predictions of microseismic excitation based on ocean wave models showed consistency with the observed microseismic energy generated by Sandy and other storms.

  12. Some regularities of spatial and time distribution of organogenous material in Upper-Pleistocene and Holocene sediments of Central Asia (from the data of Carbon-isotope dating)

    International Nuclear Information System (INIS)

    Pshenin, G.N.; Steklenkov, A.P.; Varushchenko, A.N.

    1991-01-01

    The analysis of space time distribution of ancient organogenous material is carried out through generalization of practically all available at the present time data on radiocarbon dating of Upper-Pleistocene and Holocene sediments in the Middle Asia. The investigations were performed to study the variability of humidification over the specific territory of the Middle Asia within a determined period of time. Three rather clearly limited vertical height intervals are determined by the results of the isotope dating of wood, coal, peat and mollus samples

  13. Caulogenic induction in cotyledons of stone pine (Pinus pinea): relationship between organogenic response and benzyladenine trends in selected families.

    Science.gov (United States)

    Cuesta, Candela; Rodríguez, Ana; Centeno, María Luz; Ordás, Ricardo J; Fernández, Belén

    2009-07-15

    Adventitious bud formation in stone pine cotyledons cultured in the presence of benzyladenine (BA) has been proposed as a model for the study of in vitro shoot organogenesis in conifers. This is because of its advantageous characteristics including the requirement of only one plant growth regulator (BA), the synchronous fashion of its induction, and the homogeneity and low degree of differentiation of cotyledons. Although optimal culture conditions have been developed and are currently in use, we still lack data for BA dynamics in cotyledons cultured under these conditions, and the morphological description of the early induction stages has not, until now, been approached from a histological perspective. Consequently, this is the focus of the present report. Additionally, we examined uptake and metabolism of BA in cotyledons from two selected families, previously characterized by, and selected for, the difference in the magnitude of their organogenic response. Media transfer experiments established that cotyledons should be in contact with 44.4 microM BA for at least 6h to obtain any caulogenic response (minimum shoot-induction period). Histological observations, carried out here for the first time in this species, determined that meristemoid structures had already begun to appear in explants within 12 h of culture. Moreover, results from the BA uptake and metabolism experiments indicated that the point at which explants reached the maximum concentration of active forms of BA (276.60 microM at 6 h) and the onset of the determination phase of shoot organogenesis were directly related. A direct relationship was also observed between the intensity of the caulogenic response in cotyledons from families 36 and 61 and the endogenous concentration of BA and its riboside at the start of the induction phase. Hence, family 36, characterized by its higher bud production, reached concentrations of 251.56 microM, while family 61, selected for its low bud-producing trait, only

  14. Limestone valib eetilisi firmasid / Virge Lahe

    Index Scriptorium Estoniae

    Lahe, Virge

    2008-01-01

    Endised Hansapanga investeerimisfondide analüütikud hakkavad läbi Limestone fondide pakkuma sotsiaalselt vastutustundlikku investeerimist (Socially Responsible Investing). Kommenteerivad Art Lukas ja Silver Vohu. Vt. samas: Limestone Investment Management AS

  15. CALCIUM CARBONATE DISSOLUTION RATE IN LIMESTONE CONTACTORS

    Science.gov (United States)

    The rate of carbonate mineral dissolution from limestone was studied using a rotating disk apparatus and samples of limestone of varied composition. The purpose of this study was to determine the effect of limestone composition on the kinetics of carbonate mineral dissolution. Th...

  16. Sandy PMO Disaster Relief Appropriations Act of 2013 Financial Data

    Data.gov (United States)

    Department of Homeland Security — Sandy PMO: Disaster Relief Appropriations Act of 2013 (Sandy Supplemental Bill) Financial Data. This is the Sandy Supplemental Quarterly Financial Datasets that are...

  17. Hurricane Sandy Poster (October 29, 2012)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Hurricane Sandy poster. Multi-spectral image from Suomi-NPP shows Hurricane Sandy approaching the New Jersey Coast on October 29, 2012. Poster size is approximately...

  18. Variations in DNA methylation, acetylated histone H4, and methylated histone H3 during Pinus radiata needle maturation in relation to the loss of in vitro organogenic capability.

    Science.gov (United States)

    Valledor, Luis; Meijón, Mónica; Hasbún, Rodrigo; Jesús Cañal, Maria; Rodríguez, Roberto

    2010-03-15

    Needle differentiation is a very complex process associated with the formation of a mature photosynthetic organ. From meristem differentiation to leaf maturation, gene control must play an important role switching required genes on and off to define tissue functions, with the epigenetic code being one of the main regulation mechanisms. In this work, we examined the connections between the variation in the levels of some epigenetic players (DNA methylation, acetylated histone H4 and histone H3 methylation at Lys 4 and Lys 9) at work during needle maturation. Our results indicate that needle maturation, which is associated with a decrease in organogenic capability, is related to an increase in heterochromatin-related epigenetic markers (high DNA methylation and low acetylated histone H4 levels, and the presence of histone H3 methylated at lys 9). Immunohistochemical analyses also showed that the DNA methylation of palisade parenchyma cell layers during the transition from immature to mature scions is associated with the loss of the capacity to induce adventitious organs. Copyright 2009 Elsevier GmbH. All rights reserved.

  19. Science and Sandy: Lessons Learned

    Science.gov (United States)

    Werner, K.

    2013-12-01

    Following Hurricane Sandy's impact on the mid-Atlantic region, President Obama established a Task Force to '...ensure that the Federal Government continues to provide appropriate resources to support affected State, local, and tribal communities to improve the region's resilience, health, and prosperity by building for the future.' The author was detailed from NOAA to the Task Force between January and June 2013. As the Task Force and others began to take stock of the region's needs and develop plans to address them, many diverse approaches emerged from different areas of expertise including: infrastructure, management and construction, housing, public health, and others. Decision making in this environment was complex with many interests and variables to consider and balance. Although often relevant, science and technical expertise was not always at the forefront of this process. This talk describes the author's experience with the Sandy Task Force focusing on organizing scientific expertise to support the work of the Task Force. This includes a description of federal activity supporting Sandy recovery efforts, the role of the Task Force, and lessons learned from developing a science support function within the Task Force.

  20. Absence of arabinan in the side chains of the pectic polysaccharides strongly associated with cell walls of Nicotiana plumbaginifolia non-organogenic callus with loosely attached constituent cells.

    Science.gov (United States)

    Iwai, H; Ishii, T; Satoh, S

    2001-10-01

    When leaf disks from haploid plants of Nicotiana plumbaginifolia Viv. were transformed with T-DNA and cultured on shoot-inducing medium, nonorganogenic callus. designated nolac (for non-organogenic callus with loosely attached cells), appeared on approximately 7% of leaf disks. In contrast, normal callus was generated on T-DNA-transformed leaf disks from diploid plants and on non-transformed leaf disks from haploid and diploid plants. Transmission electron microscopy revealed that the middle lamellae and the cell walls of one line of mutant callus (nolac-H14) were barely stained by ruthenium red. even after demethylesterification with NaOH, whereas the entire cell wall and the middle lamella were strongly stained in normal callus. In cultures of nolac-H14 callus, the level of sugar components of pectic polysaccharides in the hemicellulose fraction was reduced and that in the culture medium was elevated, as compared with cultures of normal callus. These results indicate that pectic polysaccharides are not retained in the cell walls and middle lamellae of nolac-H14 callus. In nolac-H14, the ratio of arabinose to galactose was low in the pectic polysaccharides purified from all cell wall fractions and from the medium, in particular, in the hemicellulose fractions. The low levels of arabinofuranosyl (T-Araf, 5-Araf, 2,5-Araf, and 3,5-Araf) residues in the pectic polysaccharides of the hemicellulosic fraction of nolac-H,14 indicated that no neutral-sugar side chains, composed mainly of linear arabinan. were present in nolac-H14. Arabinose-rich pectins. which are strongly associated with cellulose-hemicellulose complexes, might play an important role in intercellular attachment in the architecture of the cell wall.

  1. The behavior limestone under explosive load

    Science.gov (United States)

    Orlov, M. Yu; Orlova, Yu N.; Bogomolov, G. N.

    2016-11-01

    Limestone behavior under explosive loading was investigated. The behavior of the limestone by the action of the three types of explosives, including granular, ammonite and emulsion explosives was studied in detail. The shape and diameter of the explosion craters were obtained. The observed fragments after the blast have been classified as large, medium and small fragments. Three full-scale experiments were carried out. The research results can be used as a qualitative test for the approbation of numerical methods.

  2. The ecology of sandy beaches in Natal

    African Journals Online (AJOL)

    The ecology of sandy beaches in Natal. A.H. Dye, A. Mclachlan and T. Wooldridge. Department of Zoology, University of Port Elizabeth, Port Elizabeth. Data from an ecological survey of four sandy beaches on the. Natal coast of South Africa are presented. Physical para· meters such as beach profile, particle size, moisture, ...

  3. IMPLEMENTASI SANDI HILL UNTUK PENYANDIAN CITRA

    Directory of Open Access Journals (Sweden)

    JJ Siang

    2002-01-01

    Full Text Available Hill's code is one of text encoding technique. In this research, Hill's code is extended to image encoding. The image used is BMP 24 bit format. 2x2 and 3x3 matrices is used as a key. The results show that Hill's code is suitable for image whose RGB values vary highly. On the contrary, it is not suitable for less varied RGB images since its original pattern is still persisted in encrypted image. Hill's code for image encoding has also disadvantage in the case that the key matrix is not unique. However, for daily application, with good key matrix, Hill's code can be applied to encode image since it's process only deals with simple matrix operation so it become fast. Abstract in Bahasa Indonesia : Sandi Hill merupakan salah satu teknik penyandian teks. Dalam penelitian ini, pemakaian sandi Hill diperluas dari teks ke citra bertipe BMP 24 bit. Matriks yang dipakai berordo 2x2 dan 3x3. Hasil percobaan menunjukkan bahwa sandi Hill cocok untuk enkripsi citra dengan variasi nilai RGB antar piksel berdekatan yang tinggi (seperti foto, tapi tidak cocok untuk citra dengan variasi nilai RGB yang rendah (seperti gambar kartun karena pola citra asli masih tampak dalam citra sandi. Sandi Hill juga memiliki kelemahan dalam hal tidak tunggalnya matriks kunci yang dapat dipakai. Akan tetapi untuk pemakaian biasa, dengan pemilihan matriks kunci yang baik, sandi Hill dapat dipakai untuk penyandian karena hanya melibatkan operasi matriks biasa sehingga prosesnya relatif cepat. Kata kunci: Sandi Hill, Citra, Relatif Prima.

  4. Reaction between Hydrogen Sulfide and Limestone Calcines

    Czech Academy of Sciences Publication Activity Database

    Hartman, Miloslav; Svoboda, Karel; Trnka, Otakar; Čermák, Jiří

    2002-01-01

    Roč. 41, č. 10 (2002), s. 2392-2398 ISSN 0888-5885 R&D Projects: GA AV ČR IAA4072711; GA AV ČR IAA4072801 Keywords : hydrogen sulfide * limestone calcines * desulfurization Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 1.247, year: 2002

  5. Hydrogen Chloride Reaction with Lime and Limestone

    DEFF Research Database (Denmark)

    Erik Weinell, Claus; Jensen, Peter I.; Dam-Johansen, Kim

    1992-01-01

    The capacity of solid slaked lime and limestone for binding HCl from a gas phase has been investigated in the temperature range 60-1000 °C. The binding capacity is largest in the range 500-600 °C. However, for slaked lime in the presence of water, a large binding capacity is observed also below 150...

  6. Neutron activation analysis of limestone objects

    International Nuclear Information System (INIS)

    Meyers, P.; Van Zelst, L.

    1977-01-01

    The elemental composition of samples from limestone objects were determined by neutron activation analysis to investigate whether this technique can be used to distinguish between objects made of limestone from different sources. Samples weighing between 0.2-2 grams were obtained by drilling from a series of ancient Egyptian and medieval Spanish objects. Analysis was performed on aliquots varying in weight from 40-100 milligrams. The following elements were determined quantitatively: Na, K, Rb, Cs, Ba, Sc, La, Ce, Sm, Eu, Hf, Th, Ta, Cr, Mn, Fe, Co and Zn. The data on Egyptian limestones indicate that, because of the inhomogeneous nature of the stone, 0.2-2 gram samples may not be representative of an entire object. Nevertheless, multivariate statistical methods produced a clear distinction between objects originating from the Luxor area (ancient Thebes) and objects found north of Luxor. The Spanish limestone studied appeared to be more homogeneous. Samples from stylistically related objects have similar elemental compositions while relative large differences were observed between objects having no relationship other than the common provenance of medieval Spain. (orig.) [de

  7. The use of Limestone Powder as an Alternative Cement Replacement

    African Journals Online (AJOL)

    user

    focused on the effects of limestone on the cement ... construction materials in Ethiopia is increasing .... Findings of research works on the strength reveals ... This CEN standard sand is delivered ... control mix made without limestone fines.

  8. Kinetic Study of Calcination of Jakura Limestone Using Power Rate ...

    African Journals Online (AJOL)

    National Research Institute for Chemical Technology, P.M. B 1052, Zaria, ... calcination of Jakura limestone was also found to be first order reaction with respect to CaCO3 ... Keywords: Jakura, limestone, calcination, kinetics, power law model.

  9. Effect of limestone particle size on bone quality characteristics of ...

    African Journals Online (AJOL)

    A study was conducted to determine the effect of different limestone particle sizes in layer diets on bone quality characteristics at end-of-lay hens. Calcitic limestone (360 g Ca/kg DM) that is extensively used in commercial poultry diets was obtained from a specific South African source. Limestone particles were graded as ...

  10. Mangrove plantation over a limestone reef - Good for the ecology?

    Science.gov (United States)

    Asaeda, Takashi; Barnuevo, Abner; Sanjaya, Kelum; Fortes, Miguel D.; Kanesaka, Yoshikazu; Wolanski, Eric

    2016-05-01

    There have been efforts to restore degraded tropical and subtropical mangrove forests. While there have been many failures, there have been some successes but these were seldom evaluated to test to what level the created mangrove wetlands reproduce the characteristics of the natural ecosystem and thus what ecosystem services they can deliver. We provide such a detailed assessment for the case of Olango and Banacon Islands in the Philippines where the forest was created over a limestone reef where mangroves did not exist in one island but they covered most of the other island before deforestation in the 1940s and 1950s. The created forest appears to have reached a steady state after 60 years. As is typical of mangrove rehabilitation efforts worldwide, planting was limited to a single Rhizophora species. While a forest has been created, it does not mimic a natural forest. There is a large difference between the natural and planted forests in terms of forest structure and species diversity, and tree density. The high density of planted trees excludes importing other species from nearby natural forests; therefore the planted forest remains mono-specific even after several decades and shows no sign of mimicking the characteristics of a natural forest. The planted forests provided mangrove propagules that invaded nearby natural forests. The planted forest has also changed the substratum from sandy to muddy. The outline of the crown of the planted forest has become smooth and horizontal, contrary to that of a natural forest, and this changes the local landscape. Thus we recommend that future mangrove restoration schemes should modify their methodology in order to plant several species, maintain sufficient space between trees for growth, include the naturally dominant species, and create tidal creeks, in order to reproduce in the rehabilitated areas some of the key ecosystem characteristics of natural mangrove forests.

  11. Sandy a změna klimatu

    Czech Academy of Sciences Publication Activity Database

    Pecho, Jozef

    2013-01-01

    Roč. 92, č. 7 (2013), s. 408-411 ISSN 0042-4544 Institutional support: RVO:68378289 Keywords : hurricanes * climate change Subject RIV: DG - Athmosphere Sciences, Meteorology http://www.vesmir.cz/clanek/sandy-a-zmena-klimatu

  12. Heterotrophic bacterial populations in tropical sandy beaches

    Digital Repository Service at National Institute of Oceanography (India)

    Nair, S.; LokaBharathi, P.A.

    Distribution pattern of heterotrophic bacterial flora of three sandy beaches of the west coast of India was studied. The population in these beaches was microbiologically different. Population peaks of halotolerant and limnotolerant forms were...

  13. Measurement of biological oxygen demand sandy beaches

    African Journals Online (AJOL)

    Measurements of biological oxygen demand in a sandy beach using conventional .... counting the cells present in a sample of aged seawater and comparing this with .... This activity peaked at 71 % above the undisturbed level after 16 hours.

  14. Strength Characteristics of Reinforced Sandy Soil

    OpenAIRE

    S. N. Bannikov; Mahamed Al Fayez

    2005-01-01

    Laboratory tests on determination of reinforced sandy soil strength characteristics (angle of internal friction, specific cohesive force) have been carried out with the help of a specially designed instrument and proposed methodology. Analysis of the obtained results has revealed that cohesive forces are brought about in reinforced sandy soil and an angle of internal soil friction becomes larger in comparison with non-reinforced soil.

  15. Face logging in Copenhagen Limestone, Denmark

    DEFF Research Database (Denmark)

    Jakobsen, Lisa; Foged, Niels Nielsen; Erichsen, Lars

    2015-01-01

    tunnel in Copenhagen more than 2.5 km face logs were made in 467 locations at underground stations, shafts, caverns and along bored tunnels. Over 160 geotechnical boreholes, many with geophysical logging were executed prior to construction works. The bedrock consists of Paleogene "Copenhagen limestone......The requirement for excavation support can be assessed from face logging. Face logs can also improve our knowledge of lithological and structural conditions within bedrock and supplement information from boreholes and geophysical logs. During the construction of 8 km metro tunnel and 4 km heating....... The induration degrees recorded in face logs and boreholes are compared and correlated. Distinct geophysical log markers are used to divide the limestone into three units. These marker horizons are correlated between face logs and geotechnical boreholes. A 3D model of the strength variations recorded within...

  16. Plant Guide: Limestone hawksbeard: Crepis intermedia

    Science.gov (United States)

    L. St. John; D. Tilley

    2012-01-01

    Sunflower family (Asteraceae). Limestone hawksbeard is a native perennial forb with one or two stems arising from a taproot. Plants are 30-70cm tall and basal leaves are 10-40 cm long, pinnatifid, with a fairly broad, undivided midstrip and entire or dentate segments. Plants are densely or sparsely gray-tomentulose. There are 10-60 heads per plant that are 7-12...

  17. Limestone quarrying and quarry reclamation in Britain

    Science.gov (United States)

    Gunn, J.; Bailey, D.

    1993-06-01

    Limestones have been worked for many thousands of years — initially for building stone and agricultural lime and more recently for a wide range of construction and industrial uses. In most industrialized countries limestone quarries represent the most visually obvious and, in both process and landform terms, the most dramatic anthropogenic impact on karst terrain. However, quarrying has, to date, received surprisingly little attention from karst scientists. Research in the English Peak District suggested that the postexcavation evolution of quarried limestone rock faces was in part a result of the methods used in their excavation, and this led to the development of a technique designed to reduce the visual and environmental impacts of modern quarries by “Landform replication. ” This involves the use of controlled “restoration blasting” techniques on quarried rock slopes to construct a landform sequence similar to that in the surrounding natural landscape. The constructed landforms are then partially revegetated using appropriate wildflower, grass, and/or tree species.

  18. Large scale sodium interactions. Part 3. Chemical phenomena with limestone concrete

    International Nuclear Information System (INIS)

    Sallach, R.A.

    1977-01-01

    The description of the chemical processes and reaction products resulting from the exposure of concrete to molten sodium metal is important for a thorough, realistic assessment of the safety of CRBR-type reactors. Concretes are in general complex heterogenous substances whose ingredients can be derived from many sources. Consequently a wide variety of reaction processes and products might be anticipated. Initial attention has focused on a concrete in which both the aggregate and sandy components are derived from limestone. Presented are the chemical observations and experimental data from tests in which molten sodium metal at approximately 500 0 C is dropped into cold limestone concrete crucibles. Thermocouples immersed in the sodium pool indicate that the reaction proceeds in two stages. In the first stage which lasts 5 to 8 minutes, the temperature of the reacting mass hovers around 500 0 C. This stage is followed by a second stage of longer duration--greater than 100 minutes--where the temperature is 700 to 800 0 C. The main reaction product is a hard, fused, black slag which contains about 3/4 of the sodium in the initial charge. A secondary product is sodium oxide aerosol which accounts for the remaining 1/4 of the charge. It is significant that no free sodium metal is found in the slag; all sodium has completely reacted

  19. Effects of limestone, N, K and Mg fertilizers on Mg absorption by oats and barley

    Energy Technology Data Exchange (ETDEWEB)

    Alston, A M

    1966-01-01

    Oats grown in a pot experiment on two sandy loams were sampled at four stages of growth. Neither KCl nor MgSO/sub 4/. 7H/sub 2/O had any effect on yield but % Mg and total Mg uptake were consistently decreased by applying K and increased by applying Mg. Ca(NO/sub 3/)/sub 2/ increased % Mg more than did (NH/sub 4/)/sub 2/SO/sub 4/, but yield and total Mg uptake were higher where (NH/sub 4/)/sub 2/SO/sub 4/ was applied. The effects of fertilizers were similar on both soils. The effects of applying (NH/sub 4/)/sub 2/SO/sub 4/ and NaNO/sub 2/ to the soil on % Mg in barley were compared in a field experiment on an acid loam to which several rates of limestone had been applied. Treatments had no effect on the % Mg in grain or straw at maturity. At four earlier stages of growth (NH/sub 4/)/sub 2/SO)/sub 4/ increased % Mg in the plants more than did NaNO/sub 2/. Limestone slightly increased % Mg. Nitrification of NH/sub 4/ in the soil was rapid.

  20. Operational Group Sandy technical progress report

    Science.gov (United States)

    ,

    2013-01-01

    Hurricane Sandy made US landfall near Atlantic City, NJ on 29 October 2012, causing 72 direct deaths, displacing thousands of individuals from damaged or destroyed dwellings, and leaving over 8.5 million homes without power across the northeast and mid-Atlantic. To coordinate federal rebuilding activities in the affected region, the President established the cabinet-level Hurricane Sandy Rebuilding Task Force (Task Force). The Task Force was charged with identifying opportunities for achieving rebuilding success while supporting economic vitality, improving public health and safety, protecting and enhancing natural and manmade infrastructure, bolstering resilience, and ensuring appropriate accountability.

  1. Rock mass characterization for tunnels in the Copenhagen limestone

    DEFF Research Database (Denmark)

    Foged, Niels Nielsen; Jakobsen, Lisa; Jackson, Peter

    2007-01-01

    Tunnels in Copenhagen are drilled through highly anisotropic limestone comprising alternating strongly lithified and less lithified parts. The mass quality of the limestone is usually defined from fracture spacing registered in core samples. The deposit is, however, affected destructively by dril...... by drilling activity yielding a low Rock Quality Designation RQD. In-situ observations of the limestone in excavations or televiewer logs reveal only few natural discontinuities compared to core logging, indicating a very good suitability for tunneling....

  2. Mechanical Analysis Of Limestone In Jaya, Lhong, And Lhoknga

    Directory of Open Access Journals (Sweden)

    Raihan .

    2012-09-01

    Full Text Available Research about mechanical analysis of limestone in District Jaya, Lhong, and Lhoknga has been done from Dec. 2011 to Mei 2012. This study aim is to classify the limestones based on physical and mechanical tests as well as identify opportunities limestone utilization in accordance with the SII 0378-80 as a condition of quality natural stone for building. Research have been done by testing compressive strength, modulus Young, wear, specific gravity, porosity, and absorption. The result shows that the limestones are qualified natural stone for building the foundation, curbstone, stone and ornamental stone or paste.

  3. The Influence of Combustion-derived pollutants on limestone deterioration

    DEFF Research Database (Denmark)

    Johnson, J.B.; Montgomery, Melanie; Thompson, G.E.

    1996-01-01

    The wet deposition of combustion-derived atmospheric pollutant species, on to freshly cut or diesel-smoked Portland and Monks Park limestone and marble samples, was carried out in a laboratory 'wetting and drying' salt spray chamber for 84 days. Along with the effect of CO2-equilibrated de...... limestones, respectively. Thus the water and hydrogen ion loading effects are significant, as well as the limestone type, but the nature of the anion is not, under the given wetting and drying regime. Further work showed that the increased resistance of marble over that of limestone, to calcium loss...

  4. Sandy Hook : alternative access concept plan and vehicle replacement study

    Science.gov (United States)

    2009-06-01

    This study addresses two critical issues of concern to the Sandy Hook Unit of Gateway National : Recreational Area: (1) options for alternative access to Sandy Hook during peak summer season, : particularly when the park is closed to private vehicles...

  5. Modeling contaminant plumes in fractured limestone aquifers

    DEFF Research Database (Denmark)

    Mosthaf, Klaus; Brauns, Bentje; Fjordbøge, Annika Sidelmann

    Determining the fate and transport of contaminant plumes from contaminated sites in limestone aquifers is important because they are a major drinking water resource. This is challenging because they are often heavily fractured and contain chert layers and nodules, resulting in a complex transport...... model. The paper concludes with recommendations on how to identify and employ suitable models to advance the conceptual understanding and as decision support tools for risk assessment and the planning of remedial actions....... behavior. Improved conceptual models are needed for this type of site. Here conceptual models are developed by combining numerical models with field data. Several types of fracture flow and transport models are available for the modeling of contaminant transport in fractured media. These include...... the established approaches of the equivalent porous medium, discrete fracture and dual continuum models. However, these modeling concepts are not well tested for contaminant plume migration in limestone geologies. Our goal was to develop and evaluate approaches for modeling the transport of dissolved contaminant...

  6. The ecology of sandy beaches in Transkei

    African Journals Online (AJOL)

    Data from an ecological survey of three sandy beaches in. Transkei and from Gulu beach on the eastern Cape coast,. South Africa, are presented. Physical parameters such as beach profile, sand particle size, Eh and carbonate content, as well as abundance, composition, biomass and distribution of the macrofauna and ...

  7. Lessons from Hurricane Sandy for port resilience.

    Science.gov (United States)

    2013-12-01

    New York Harbor was directly in the path of the most damaging part of Hurricane Sandy causing significant impact on many of the : facilities of the Port of New York and New Jersey. The U.S. Coast Guard closed the entire Port to all traffic before the...

  8. Transportation during and after Hurricane Sandy.

    Science.gov (United States)

    2012-11-01

    "Hurricane Sandy demonstrated the strengths and limits of the transportation infrastructure in New York City and the surrounding region. As a result of the timely and thorough preparations by New York City and the MTA, along with the actions of city ...

  9. Bibliography of sandy beaches and sandy beach organisms on the African continent

    CSIR Research Space (South Africa)

    Bally, R

    1986-01-01

    Full Text Available This bibliography covers the literature relating to sandy beaches on the African continent and outlying islands. The bibliography lists biological, chemical, geographical and geological references and covers shallow marine sediments, surf zones off...

  10. STEAM INJECTION INTO FRACTURED LIMESTONE AT LORING AIR FORCE BASE

    Science.gov (United States)

    A research project on steam injection for the remediation of spent chlorinated solvents from fractured limestone was recently undertaken at the former Loring AFB in Limestone, ME. Participants in the project include the Maine Department of Environmental Protection, EPA Region I,...

  11. Catalytic and Gas-Solid Reactions Involving HCN over Limestone

    DEFF Research Database (Denmark)

    Jensen, Anker; Johnsson, Jan Erik; Dam-Johansen, Kim

    1997-01-01

    In coal-fired combustion systems solid calcium species may be present as ash components or limestone added to the combustion chamber. In this study heterogeneous reactions involving HCN over seven different limestones were investigated in a laboratory fixed-bed quartz reactor at 873-1,173 K...

  12. Effect of limestone particle size on egg production and eggshell ...

    African Journals Online (AJOL)

    Different limestone particle sizes had no effect on any of the tested egg production and eggshell quality parameters. These results suggested that larger particles limestone are not necessarily essential to provide sufficient Ca2+ to laying hens for egg production and eggshell quality at end-of-lay, provided that the dietary Ca ...

  13. Field trial of a pulsed limestone diversion well

    Science.gov (United States)

    Sibrell, Philip L.; Denholm, C.; Dunn, Margaret

    2013-01-01

    The use of limestone diversion wells to treat acid mine drainage (AMD) is well-known, but in many cases, acid neutralization is not as complete as would be desired. Reasons for this include channeling of the water through the limestone bed, and the slow reaction rate of the limestone gravel. A new approach to improve the performance of the diversion well was tested in the field at the Jennings Environmental Education Center, near Slippery Rock, PA. In this approach, a finer size distribution of limestone was used so as to allow fluidization of the limestone bed, thus eliminating channeling and increasing particle surface area for faster reaction rates. Also, water flow was regulated through the use of a dosing siphon, so that consistent fluidization of the limestone sand could be achieved. Testing began late in the summer of 2010, and continued through November of 2011. Initial system performance during the 2010 field season was good, with the production of net alkaline water, but hydraulic problems involving air release and limestone sand retention were observed. In the summer of 2011, a finer size of limestone sand was procured for use in the system. This material fluidized more readily, but acid neutralization tapered off after several days. Subsequent observations indicated that the hydraulics of the system was compromised by the formation of iron oxides in the pipe leading to the limestone bed, which affected water distribution and flow through the bed. Although results from the field trial were mixed, it is believed that without the formation of iron oxides and plugging of the pipe, better acid neutralization and treatment would have occurred. Further tests are being considered using a different hydraulic configuration for the limestone sand fluidized bed.

  14. Responses of soil fungal community to the sandy grassland restoration in Horqin Sandy Land, northern China.

    Science.gov (United States)

    Wang, Shao-Kun; Zuo, Xiao-An; Zhao, Xue-Yong; Li, Yu-Qiang; Zhou, Xin; Lv, Peng; Luo, Yong-Qing; Yun, Jian-Ying

    2016-01-01

    Sandy grassland restoration is a vital process including re-structure of soils, restoration of vegetation, and soil functioning in arid and semi-arid regions. Soil fungal community is a complex and critical component of soil functioning and ecological balance due to its roles in organic matter decomposition and nutrient cycling following sandy grassland restoration. In this study, soil fungal community and its relationship with environmental factors were examined along a habitat gradient of sandy grassland restoration: mobile dunes (MD), semi-fixed dunes (SFD), fixed dunes (FD), and grassland (G). It was found that species abundance, richness, and diversity of fungal community increased along with the sandy grassland restoration. The sequences analysis suggested that most of the fungal species (68.4 %) belonged to the phylum of Ascomycota. The three predominant fungal species were Pleospora herbarum, Wickerhamomyces anomalus, and Deconica Montana, accounting for more than one fourth of all the 38 species. Geranomyces variabilis was the subdominant species in MD, Pseudogymnoascus destructans and Mortierella alpine were the subdominant species in SFD, and P. destructans and Fungi incertae sedis were the dominant species in FD and G. The result from redundancy analysis (RDA) and stepwise regression analysis indicated that the vegetation characteristics and soil properties explain a significant proportion of the variation in the fungal community, and aboveground biomass and C:N ratio are the key factors to determine soil fungal community composition during sandy grassland restoration. It was suggested that the restoration of sandy grassland combined with vegetation and soil properties improved the soil fungal diversity. Also, the dominant species was found to be alternative following the restoration of sandy grassland ecosystems.

  15. Rebuilding Emergency Care After Hurricane Sandy.

    Science.gov (United States)

    Lee, David C; Smith, Silas W; McStay, Christopher M; Portelli, Ian; Goldfrank, Lewis R; Husk, Gregg; Shah, Nirav R

    2014-04-09

    A freestanding, 911-receiving emergency department was implemented at Bellevue Hospital Center during the recovery efforts after Hurricane Sandy to compensate for the increased volume experienced at nearby hospitals. Because inpatient services at several hospitals remained closed for months, emergency volume increased significantly. Thus, in collaboration with the New York State Department of Health and other partners, the Health and Hospitals Corporation and Bellevue Hospital Center opened a freestanding emergency department without on-site inpatient care. The successful operation of this facility hinged on key partnerships with emergency medical services and nearby hospitals. Also essential was the establishment of an emergency critical care ward and a system to monitor emergency department utilization at affected hospitals. The results of this experience, we believe, can provide a model for future efforts to rebuild emergency care capacity after a natural disaster such as Hurricane Sandy. (Disaster Med Public Health Preparedness. 2014;0:1-4).

  16. Liquification and soft-sediment deformation in a limestone megabreccia: The Ayabacas giant collapse, Cretaceous, southern Peru

    Science.gov (United States)

    Callot, Pierre; Odonne, Francis; Sempere, Thierry

    2008-12-01

    In the back-arc basin of southern Peru, the bulk of the mid-Cretaceous carbonate platform collapsed near the Turonian-Coniacian boundary (~ 90-89 Ma), due to slope creation and resulting oversteepening. The resulting mass-wasting deposits, namely the Ayabacas Formation, consist of a megabreccia which is organised from NE to SW in relation with two major fault systems. Facies of sediment reworking (such as brecciation, liquification, sedimentary dykes and soft-sediment deformation) are described and four types of resedimentation facies are define. In the northeastern part of the study area, deposits mainly consist of a mixture of very heterometric clasts and blocks (millimetric to kilometric in size), mainly carbonate but also sandy-marly in nature, floating in sandy-marly matrix that exhibits features of liquification (sedimentary dykes and flows) and plastic deformation. Here, resedimentation facies are characterized by deformations and a brecciated facies at each observation scale (from aerial photographs to thin sections) and are therefore defined as fractal or multi-scale breccias. Some clasts and large amounts of the matrix were derived from the underlying clay-rich sandstones of the Murco Formation. These materials were prone to liquification and plastic deformation, allowing them to act as a sliding sole that facilitated the slides and the downslope movement of large limestone rafts. In the southwestern part of the study area, only limestone breccias are observed, in alternation with well-stratified levels. The sliding sole of plastically deformable siliciclastic sediments that previously acted as a lubricating layer was not present here, as materials were more deeply buried. Variations in the degree of sediment lithification from northeast to southwest are inferred to have existed before the collapse and also within the sedimentary succession in the northeastern part. In particular, limestones were well-cemented at the base of the carbonate succession and

  17. Electrical conductivity of sandstone, limestone, and granite

    Energy Technology Data Exchange (ETDEWEB)

    Duba, A.; Piwinskii, A.J.; Santor, M.; Weed, H.C.

    1978-01-01

    The electrical conductivity of cylindrical cores of Westerly granite, Indiana limestone and Nugget, St Peter and Kayenta sandstones was measured at about 25/sup 0/C in vacuo, in air, and after saturation in distilled water, tap water, and 0.1 M NaCl solution. The three-electrode technique with a guard ring and the two-electrode technique without a guard ring were used. Core aspect ratio over the range of 2.00 to 0.25, as well as frequency over the range of 50 Hz to 10 kHz, influences the conductivity of all rocks, especially those measured in vacuo. Measurements from water-saturated samples using a guard ring are not appreciably different from those obtained without a guard ring. The conductivity of rocks saturated in 0.1 M NaCl solution changes least with a change in aspect ratio; for these rocks a linear relationship, known as Archie's Law, exists between log porosity and log conductivity. No simple correlation was found between those factors in rocks saturated with tap or distilled water. Thus, it appears Archie's Law is of questionable value for correlating laboratory data from rocks saturated with low-conductivity fluids.

  18. Residual CO2 trapping in Indiana limestone.

    Science.gov (United States)

    El-Maghraby, Rehab M; Blunt, Martin J

    2013-01-02

    We performed core flooding experiments on Indiana limestone using the porous plate method to measure the amount of trapped CO(2) at a temperature of 50 °C and two pressures: 4.2 and 9 MPa. Brine was mixed with CO(2) for equilibration, then the mixture was circulated through a sacrificial core. Porosity and permeability tests conducted before and after 884 h of continuous core flooding confirmed negligible dissolution. A trapping curve for supercritical (sc)CO(2) in Indiana showing the relationship between the initial and residual CO(2) saturations was measured and compared with that of gaseous CO(2). The results were also compared with scCO(2) trapping in Berea sandstone at the same conditions. A scCO(2) residual trapping end point of 23.7% was observed, indicating slightly less trapping of scCO(2) in Indiana carbonates than in Berea sandstone. There is less trapping for gaseous CO(2) (end point of 18.8%). The system appears to be more water-wet under scCO(2) conditions, which is different from the trend observed in Berea; we hypothesize that this is due to the greater concentration of Ca(2+) in brine at higher pressure. Our work indicates that capillary trapping could contribute to the immobilization of CO(2) in carbonate aquifers.

  19. LUTETIAN LIMESTONES IN THE PARIS REGION: PETROGRAPHIC AND COMPOSITIONAL EXAMINATION

    International Nuclear Information System (INIS)

    BLANC, A.; HOLMES, L.L.; HARBOTTLE, G.

    1998-01-01

    Stone for building and decorating monuments in the Paris Basin from antiquity to the present came from numerous quarries in the Lutetian limestone formations of the region. To identify specific-stone sources used for masonry and sculptures in these monuments, a team of geologists and archaeologists has investigated 300 quarries and collected 2,300 limestone samples for study in a collaborative effort by geologists and chemists. Petrographic and paleontologic examinations of thin sections enable geologists to distinguish the Tertiary Lutetian limestones from similar stone in Jurassic and Cretaceous strata. The methods of the geologist have been supplemented by those of the chemist whose compositional studies by neutron activation analysis can differentiate among the fine-grained upper Lutetian limestones extracted from specific ancient quarries

  20. Improving DMS 9210 requirements for limestone rock asphalt - final report.

    Science.gov (United States)

    2015-03-01

    Limestone Rock Asphalt (LRA) mixtures have been produced and placed for several decades using : specification requirements currently listed under DMS 9210. Several districts have had placement issues : and premature failures at the beginning of 2010....

  1. Limestone doses affecting mineral contents in tropical grass forage

    International Nuclear Information System (INIS)

    Armelin, M.J.A.; Saiki, M.

    2005-01-01

    Field trial was performed at the experimental farm of Southeast Embrapa Cattle, Sao Carlos - SP, Brazil, on a 16 year old Brachiaria decumbens pasture, grown on a distrophic Hapludox (Oxisol), recovered by the use of limestone and fertilizer. The experiments were carried out in random blocks, with 6 replications and 5 treatments. The 100 m 2 blocks were established in the pasture. Each block received a sequence of limestone doses of 0, 1, 2, 4 and 8 t/ha. The forage samples were taken one year after limestone application on soil surface. Instrumental neutron activation analysis (INAA) followed by gamma-ray spectrometry was the analytical method used to determine mineral contents. The statistical analysis showed a negative linear correlation of Br, Co, Cr, Mn and Zn contents in forage with the limestone doses, while the uptake of Mg was affected in a positive way. (author)

  2. Epidemic gasoline exposures following Hurricane Sandy.

    Science.gov (United States)

    Kim, Hong K; Takematsu, Mai; Biary, Rana; Williams, Nicholas; Hoffman, Robert S; Smith, Silas W

    2013-12-01

    Major adverse climatic events (MACEs) in heavily-populated areas can inflict severe damage to infrastructure, disrupting essential municipal and commercial services. Compromised health care delivery systems and limited utilities such as electricity, heating, potable water, sanitation, and housing, place populations in disaster areas at risk of toxic exposures. Hurricane Sandy made landfall on October 29, 2012 and caused severe infrastructure damage in heavily-populated areas. The prolonged electrical outage and damage to oil refineries caused a gasoline shortage and rationing unseen in the USA since the 1970s. This study explored gasoline exposures and clinical outcomes in the aftermath of Hurricane Sandy. Prospectively collected, regional poison control center (PCC) data regarding gasoline exposure cases from October 29, 2012 (hurricane landfall) through November 28, 2012 were reviewed and compared to the previous four years. The trends of gasoline exposures, exposure type, severity of clinical outcome, and hospital referral rates were assessed. Two-hundred and eighty-three gasoline exposures were identified, representing an 18 to 283-fold increase over the previous four years. The leading exposure route was siphoning (53.4%). Men comprised 83.0% of exposures; 91.9% were older than 20 years of age. Of 273 home-based calls, 88.7% were managed on site. Asymptomatic exposures occurred in 61.5% of the cases. However, minor and moderate toxic effects occurred in 12.4% and 3.5% of cases, respectively. Gastrointestinal (24.4%) and pulmonary (8.4%) symptoms predominated. No major outcomes or deaths were reported. Hurricane Sandy significantly increased gasoline exposures. While the majority of exposures were managed at home with minimum clinical toxicity, some patients experienced more severe symptoms. Disaster plans should incorporate public health messaging and regional PCCs for public health promotion and toxicological surveillance.

  3. A Metagenomic Survey of Limestone Hill in Taiwan

    Science.gov (United States)

    Hsu, Y. W.; Li, K. Y.; Chen, Y. W.; Huang, T. Y.; Chen, W. J.; Shih, Y. J.; Chen, J. S.; Fan, C. W.; Hsu, B. M.

    2016-12-01

    The limestone of Narro-Sky in Tainliao, Taiwan is of Pleistocene reef limestones interbedded in clastic layers that covered the Takangshan anticlines. Understanding how microbial relative abundance was changed in response to changes of environmental factors may contribute to better comprehension of roles that microorganisms play in altering the landscape structures. In this study, microorganisms growing on the wall of limestone, in the water dripping from the limestone wall and of soil underneath the wall were collected from different locations where the environmental factors such as daytime illumination, humidity, or pH are different. Next generation sequencing (NGS) was carried out to examine the compositions and richness of microbial community. The metagenomics were clustered into operational taxonomic units (OTUs) to analyze relative abundance, diversities and principal coordinates analysis (PCoA). Our results showed the soil sample has the highest alpha diversity while water sample has the lowest. Four major phyla, which are Proteobacteria, Acidobacteria, Actinobacteria, and Cyanobacteria, account for 80 % of total microbial biomass in all groups. Cyanobacteria were found most abundantly in limestone wall instead of water or soil of weathering limestone. The PCoA dimensional patterns of each phylum showed a trace of microbial community dynamic changes, which might be affected by environmental factors. This study provides the insights to understand how environmental factors worked together with microbial community to shape landscape structures.

  4. Converting SDAP into gypsum in a wet limestone scrubber

    Energy Technology Data Exchange (ETDEWEB)

    Fogh, F [Faelleskemikerne, Elsamprojekt A/S, Fredericia (Denmark)

    1996-12-01

    The ELSAM power pool has an installed electrical capacity of approx. 5 GW{sub e}, mainly firing import coal. The major base load units are equipped with desulphurization units and three different desulphurization technologies are used: the wet limestone gypsum process, the spray dry absorption process and a sulphuric acid process. Gypsum and sulphuric acid are commercialized, whereas it has been difficult to utilize the spray dry absorption product (SDAP). The main constituents of SDAP are calcium sulphide, calcium chloride, hydrated lime and impurities mainly originating from fly ash. Sulphide can be oxidized into sulphate in acidic solution - the reaction is utilized in the wet limestone gypsum process - and the possibility of using any spare capacity in the wet limestone gypsum units to oxidize the sulphide content of SDAP into sulphate and produce usable gypsum has been investigated in the laboratory and in a 400 MW{sub e} equivalent wet limestone unit. The limestone inhibition effect of the addition of SDAP is currently being studied in the laboratory in order to determine the effect of different SDAP types (plant/coal sources) on limestone reactivity before further long-term full-scale tests are performed and permanent use of the process planned. (EG)

  5. Influence of limestone on the hydration of Portland cements

    International Nuclear Information System (INIS)

    Lothenbach, Barbara; Le Saout, Gwenn; Gallucci, Emmanuel; Scrivener, Karen

    2008-01-01

    The influence of the presence of limestone on the hydration of Portland cement was investigated. Blending of Portland cement with limestone was found to influence the hydrate assemblage of the hydrated cement. Thermodynamic calculations as well as experimental observations indicated that in the presence of limestone, monocarbonate instead of monosulfate was stable. Thermodynamic modelling showed that the stabilisation of monocarbonate in the presence of limestone indirectly stabilised ettringite leading to a corresponding increase of the total volume of the hydrate phase and a decrease of porosity. The measured difference in porosity between the 'limestone-free' cement, which contained less than 0.3% CO 2 , and a cement containing 4% limestone, however, was much smaller than calculated. Coupling of thermodynamic modelling with a set of kinetic equations which described the dissolution of the clinker, predicted quantitatively the amount of hydrates. The quantities of ettringite, portlandite and amorphous phase as determined by TGA and XRD agreed well with the calculated amounts of these phases after different periods of time. The findings in this paper show that changes in the bulk composition of hydrating cements can be followed by coupled thermodynamic models. Comparison between experimental and modelled data helps to understand in more detail the dominating processes during cement hydration

  6. Modeling the influence of limestone addition on cement hydration

    Directory of Open Access Journals (Sweden)

    Ashraf Ragab Mohamed

    2015-03-01

    Full Text Available This paper addresses the influence of using Portland limestone cement “PLC” on cement hydration by characterization of its microstructure development. The European Standard EN 197-1:2011 and Egyptian specification ESS 4756-1/2009 permit the cement to contain up to 20% ground limestone. The computational tools assist in better understanding the influence of limestone additions on cement hydration and microstructure development to facilitate the acceptance of these more economical and ecological materials. μic model has been developed to enable the modeling of microstructural evolution of cementitious materials. In this research μic model is used to simulate both the influence of limestone as fine filler, providing additional surfaces for the nucleation and growth of hydration products. Limestone powder also reacts relatively slow with hydrating cement to form monocarboaluminate (AFmc phase, similar to the mono-sulfoaluminate (AFm phase formed in ordinary Portland cement. The model results reveal that limestone cement has accelerated cement hydration rate, previous experimental results and computer model “cemhyd3d” are used to validate this model.

  7. Thermal properties of the Cobourg Limestone

    Science.gov (United States)

    Pitts, Michelle

    The underground storage of used nuclear fuel in Deep Geologic Repositories (DGRs) has been a subject of research in Canada for decades. One important technical aspect of repository design is the accommodation of the mechanical impacts of thermal inputs (heating) from the fuel as it goes through the remainder of its life cycle. Placement room spacing, a major factor in project cost, will be determined by the ability of the host rock to dissipate heat. The thermal conductivity and linear thermal expansion will determine the evolution of the temperature and thermally-induced stress fields. Thermal processes must be well understood to design a successful DGR. This thesis examines the thermal properties of rocks, how they are influenced by factors such as temperature, pressure, mineralogy, porosity, and saturation; and common methods for calculating and/or measuring these properties. A brief overview of thermal and thermally-coupled processes in the context of DGRs demonstrates the degree to which they would impact design, construction, and operation of these critical structures. Several case histories of major in situ heating experiments are reviewed to determine how the lessons learned could be applied to a Canadian Underground Demonstration Facility (UDF). A mineralogy investigation using X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) examines samples of the Cobourg Limestone from the Bowmanville and Bruce sites, and demonstrates geographical variability within the Cobourg Formation. The thermal properties of samples from the Bowmanville site are determined. A divided bar apparatus was constructed and used to measure thermal conductivity. The temperature measurement component of the divided bar apparatus was used to measure linear thermal expansion. Finally, the past investigations into the thermal impact of a DGR are reviewed, and the implications of the laboratory testing results on similar analyses are discussed.

  8. Radon emanation coefficients in sandy soils

    International Nuclear Information System (INIS)

    Holy, K.; Polaskova, A.; Baranova, A.; Sykora, I.; Hola, O.

    1998-01-01

    In this contribution the results of the study of an influence of the water content on the emanation coefficient for two sandy soil samples are reported. These samples were chosen on the because of the long-term continual monitoring of the 222 Rn concentration just in such types of soils and this radon concentration showed the significant variations during a year. These variations are chiefly given in connection with the soil moisture. Therefore, the determination of the dependence of the emanation coefficient of radon on the water content can help to evaluate the influence of the soil moisture variations of radon concentrations in the soil air. The presented results show that the emanation coefficient reaches the constant value in the wide interval of the water content for both sandy soil samples. Therefore, in the common range of the soil moisture (5 - 20 %) it is impossible to expect the variations of the radon concentration in the soil air due to the change of the emanation coefficient. The expressive changes of the radon concentration in the soil air can be observed in case of the significant decrease of the emanation coefficient during the soil drying when the water content decreases under 5 % or during the complete filling of the soil pores by the water. (authors)

  9. Hurricane Sandy science plan: coastal impact assessments

    Science.gov (United States)

    Stronko, Jakob M.

    2013-01-01

    Hurricane Sandy devastated some of the most heavily populated eastern coastal areas of the Nation. With a storm surge peaking at more than 19 feet, the powerful landscape-altering destruction of Hurricane Sandy is a stark reminder of why the Nation must become more resilient to coastal hazards. In response to this natural disaster, the U.S. Geological Survey (USGS) received a total of $41.2 million in supplemental appropriations from the Department of the Interior (DOI) to support response, recovery, and rebuilding efforts. These funds support a science plan that will provide critical scientific information necessary to inform management decisions for recovery of coastal communities, and aid in preparation for future natural hazards. This science plan is designed to coordinate continuing USGS activities with stakeholders and other agencies to improve data collection and analysis that will guide recovery and restoration efforts. The science plan is split into five distinct themes: coastal topography and bathymetry, impacts to coastal beaches and barriers, impacts of storm surge, including disturbed estuarine and bay hydrology, impacts on environmental quality and persisting contaminant exposures, impacts to coastal ecosystems, habitats, and fish and wildlife. This fact sheet focuses assessing impacts to coastal beaches and barriers.

  10. Attrition of limestone by impact loading in fluidized beds

    Energy Technology Data Exchange (ETDEWEB)

    Fabrizio Scala; Fabio Montagnaro; Piero Salatino [Consiglio Nazionale delle Ricerche, Napoli (Italy). Istituto di Ricerche sulla Combustione

    2007-09-15

    The present study addresses limestone attrition and fragmentation associated with impact loading, a process which may occur extensively in various regions of fluidized bed (FB) combustors/gasifiers, primarily the jetting region of the bottom bed, the exit region of the riser, and the cyclone. An experimental protocol for the characterization of the propensity of limestone to undergo attrition/fragmentation by impact loading is reported. The application of the protocol is demonstrated with reference to an Italian limestone whose primary fragmentation and attrition by surface wear have already been characterized in previous studies. The experimental procedure is based on the characterization of the amount and particle size distribution of the debris generated upon the impact of samples of sorbent particles against a target. Experiments were carried out at a range of particle impact velocities between 10 and 45 m/s, consistent with jet velocities corresponding to typical pressure drops across FB gas distributors. The protocol has been applied to either raw or preprocessed limestone samples. In particular, the effect of calcination, sulfation, and calcination/recarbonation cycles on the impact damage suffered by sorbent particles has been assessed. The measurement of particle voidage and pore size distribution by mercury intrusion was also accomplished to correlate fragmentation with the structural properties of the sorbent samples. Fragmentation by impact loading of the limestone is significant. Lime displays the largest propensity to undergo impact damage, followed by the sorbent sulfated to exhaustion, the recarbonated sorbent, and the raw limestone. Fragmentation of the raw limestone and of the sulfated lime follows a pattern typical of the failure of brittle materials. The fragmentation behavior of lime and recarbonated lime better conforms to a disintegration failure mode, with an extensive generation of very fine fragments. 27 refs., 9 figs. 1 tab.

  11. Correlation between landscape fragmentation and sandy desertification: a case study in Horqin Sandy Land, China.

    Science.gov (United States)

    Ge, Xiaodong; Dong, Kaikai; Luloff, A E; Wang, Luyao; Xiao, Jun; Wang, Shiying; Wang, Qian

    2016-01-01

    The exact roles of landscape fragmentation on sandy desertification are still not fully understood, especially with the impact of different land use types in spatial dimension. Taking patch size and shape into consideration, this paper selected the Ratio of Patch Size and the Fractal Dimension Index to establish a model that reveals the association between the area of bare sand land and the fragmentation of different land use types adjacent to bare sand land. Results indicated that (1) grass land and arable land contributed the most to landscape fragmentation processes in the regions adjacent to bare sand land during the period 1980 to 2010. Grass land occupied 54 % of the region adjacent to bare sand land in 1980. The Ratio of Patch Size of grass land decreased from 1980 to 2000 and increased after 2000. The Fractal Dimension Index of grass increased during the period 1980 to 1990 and decreased after 1990. Arable land expanded significantly during this period. The Ratio of Patch Size of arable land increased from 1980 to 1990 and decreased since 1990. The Fractal Dimension Index of arable land increased from 1990 to 2000 and decreased after 2000. (2) The Ratio of Patch Size and the Fractal Dimension Index were significantly related to the area of bare sand land. The role of landscape fragmentation was not linear to sandy desertification. There were both positive and negative effects of landscape fragmentation on sandy desertification. In 1980, the Ratio of Patch Size and the Fractal Dimension Index were negatively related to the area of bare sand land, showing that the landscape fragmentation and regularity of patches contributed to the expansion of sandy desertification. In 1990, 2000, and 2010, the Ratio of Patch Size and the Fractal Dimension Index were mostly positively related to the area of bare sand land, showing the landscape fragmentation and regularity of patches contributed to the reversion of sandy desertification in this phase. The absolute values of

  12. Performance of japanese quails fed feeds containing different corn and limestone particle sizes

    Directory of Open Access Journals (Sweden)

    DA Berto

    2007-09-01

    Full Text Available This study aimed at evaluating performance and egg quality of Japanese quails fed feeds containing different corn and limestone particle sizes. A total number of 648 birds in the peak of production was distributed in a random complete block experimental design, using a 2x3 factorial arrangement (2 corn particle sizes and 3 limestone particle sizes. Birds were designated to one of two blocks, with six replicates of 18 birds each. Mean geometric diameter (MGD values used were 0.617mm and 0.723mm (corn fine and coarse particle sizes, respectively, and 0.361mm, 0.721mm, and 0.947mm (limestone fine, intermediate and coarse particle sizes, respectively. The following treatments were applied: T1: fine corn feed, with 100% fine limestone; T2: fine corn feed, with 50% fine limestone and 50% intermediate limestone; T3: fine corn feed, with 50% fine limestone and 50% coarse limestone; T4: coarse corn feed, with 100% fine limestone; T5: coarse corn feed, with 50% fine limestone and 50% intermediate limestone; T6: coarse corn feed, with 50% fine limestone and 50% coarse limestone. The experiment lasted 112 days, consisting of 4 cycles of 28 days. No significant interaction was observed among corn and limestone particle sizes for any of the analyzed parameters. There were no significant effects (p>0.05 of the tested corn particle sizes on quail performance or egg quality. There were significant (p<0.05 isolated effects of limestone particle size only on the percentage of cracked eggs, which was reduced when birds fed 50% coarse limestone (0.947mm and 50% fine limestone (0.361mm as compared to those fed 100% fine limestone. Therefore, the inclusion of 50% coarse limestone (0.947mm is recommended for quail egg production.

  13. CALCIUM OXIDE CHARACTERISTICS PREPARED FROM AMBUNTEN’S CALCINED LIMESTONE

    Directory of Open Access Journals (Sweden)

    Fatimatul Munawaroh

    2018-05-01

    Full Text Available Calcium oxide (CaO and calcium carbonate (CaCO3 are widely used in industry. CaO and CaCO3 can be synthesized or derived from limestone. The purpose of this study to determine the characteristics of CaO calcined limestone from Ambunten Sumenep. Lime in calcined at 850 ° C for 6 hours. Characterization of X-ray fluorescence (XRF was conducted to determine the chemical composition of limestone, X-ray diffraction test (XRD to find the lime crystalline phase and FTIR test to determine the absorption of wave number. XRF test results showed that the limestone chemical composition consisted of Ca of 95.37% as the dominant element, Mg of 4.1%, Fe 0.17% and Y by 0.39%. The XRD test results showed that the limestone crystal phase is ankerite (Ca [Fe, Mg] [CO3] 2 and after the calcined phase calcination is vaterite (Ca [OH] 2, calcite (CaO and calcite (CaCO3. While the FTIR test results show that the CaO spectra are seen at 3741.24, 1417.12 and 874.14 cm-1.

  14. Modifying the properties of finely ground limestone by tumbling granulation

    Science.gov (United States)

    Macho, Oliver; Eckert, Maroš; Tomášová, Barbora; Peciar, Peter; Ščasný, Martin; Fekete, Roman; Peciar, Marián

    2016-06-01

    Calcium carbonate in the form of finely ground limestone is a material that has found its application in a wide range of industries, in the chemical, rubber, agricultural, and paper industries, is used for desulfurization of boilers and other. In civil engineering, ground limestone is used for the production of building materials, plaster and mortar mixtures, as a filler in concrete mixtures, in road construction, and as an essential component of mastic asphalt. This paper deals with examining the modification of the properties of finely ground limestone by the tumbling agglomeration method. It has been shown that the components of concrete with a round grain have a positive effect on the pumping of concrete in comparison with an elongated grain or the rough surface of crushed stone. The experiments will be carried out on a granulation plate using a variety of granulation liquid. The agglomerates and their properties were compared with untreated finely ground limestone, with a focus on detecting changes in compressibility, density and particle size. The output of this paper is a description and graphical representation of the changes in the properties of ground limestone before and after the agglomeration process.

  15. Characterization of Limestone as Raw Material to Hydrated Lime

    Science.gov (United States)

    Salem Hwidi, Rajeb; Nuraiti Tengku Izhar, Tengku; Saad, Farah Naemah Mohd

    2018-03-01

    In Malaysia, limestone is essentially important for the economic growth as raw materials in the industry sector. Nevertheless, a little attention was paid to the physical, chemical, mineralogical, and morphological properties of the limestone using X-ray fluorescence (X-RF), X-ray diffraction (X-RD), Fourier transform infrared spectroscopy (FTIR), and Scanning electron microscopy / energy dispersive x-ray spectroscopy (SEM-EDS) respectively. Raw materials (limestone rocks) were collected from Bukit Keteri area, Chuping, Kangar, Perlis, Malaysia. Lab crusher and lab sieved were utilized to prepare five different size of ground limestone at (75 µm, 150 µm, 225 µm, 300, and 425 µm) respectively. It is found that the main chemical composition of bulk limestone was Calcium oxide (CaO) at 97.58 wt.% and trace amount of MnO, Al2O3, and Fe2O3 at 0.02%, 0.35%, and 0.396% respectively. XRD diffractograms showed characteristic peaks of calcite and quartz. Furthermore, main FTIR absorption bands at 1,419, 874.08 and 712.20 cm-1 indicated the presence of calcite. The micrographs showed clearly the difference of samples particle size. Furthermore, EDS peaks of Ca, O, and C elements confirmed the presence of CaCO3 in the samples.

  16. Modifying the properties of finely ground limestone by tumbling granulation

    Directory of Open Access Journals (Sweden)

    Macho Oliver

    2016-06-01

    Full Text Available Calcium carbonate in the form of finely ground limestone is a material that has found its application in a wide range of industries, in the chemical, rubber, agricultural, and paper industries, is used for desulfurization of boilers and other. In civil engineering, ground limestone is used for the production of building materials, plaster and mortar mixtures, as a filler in concrete mixtures, in road construction, and as an essential component of mastic asphalt. This paper deals with examining the modification of the properties of finely ground limestone by the tumbling agglomeration method. It has been shown that the components of concrete with a round grain have a positive effect on the pumping of concrete in comparison with an elongated grain or the rough surface of crushed stone. The experiments will be carried out on a granulation plate using a variety of granulation liquid. The agglomerates and their properties were compared with untreated finely ground limestone, with a focus on detecting changes in compressibility, density and particle size. The output of this paper is a description and graphical representation of the changes in the properties of ground limestone before and after the agglomeration process.

  17. Nitrate reduction in an unconfined sandy aquifer

    DEFF Research Database (Denmark)

    Postma, Diederik Jan; Boesen, Carsten; Kristiansen, Henning

    1991-01-01

    of total dissolved ions in the NO3- free anoxic zone indicates the downward migration of contaminants and that active nitrate reduction is taking place. Nitrate is apparently reduced to N2 because both nitrite and ammonia are absent or found at very low concentrations. Possible electron donors......Nitrate distribution and reduction processes were investigated in an unconfined sandy aquifer of Quaternary age. Groundwater chemistry was studied in a series of eight multilevel samplers along a flow line, deriving water from both arable and forested land. Results show that plumes of nitrate...... processes of O2 and NO3- occur at rates that are fast compared to the rate of downward water transport. Nitrate-contaminated groundwater contains total contents of dissolved ions that are two to four times higher than in groundwater derived from the forested area. The persistence of the high content...

  18. Modelling the morphology of sandy spits

    DEFF Research Database (Denmark)

    Pedersen, Dorthe; Deigaard, Rolf; Fredsøe, Jørgen

    2008-01-01

    The shape, dimensions and growth rate of an accumulating sandy spit is investigated by a theoretical and experimental study. The idealised case of a spit growing without change of form under a constant wave forcing is considered. The longshore wave-driven sediment transport is taken to be dominant...... that with this assumption the dimensions of the spit cannot be determined. The width and shape of a finite spit is therefore determined from simulations with an area model for the wave-driven current and sediment transport along the spit. In this case the curvature effects from the spit on the longshore sediment transport...... conducted in a wave tank an accumulating spit was formed at the down-drift end of a uniform stretch of coast exposed to waves approaching at an angle. The spit approached equilibrium dimensions when a constant wave climate was applied. The radius of curvature of the spit varied according to the height...

  19. Initial kinetics of the direct sulfation of limestone

    DEFF Research Database (Denmark)

    Hu, Guilin; Shang, Lei; Dam-Johansen, Kim

    2008-01-01

    The initial kinetics of direct sulfation of Faxe Bryozo, a porous bryozoan limestone was studied in the temperature interval from 873 to 973 K in a pilot entrained flow reactor with very short reaction times (between 0.1 and 0.6 s). The initial conversion rate of the limestone - for conversions...... less than 0.3% - was observed to be significantly promoted by higher SO2 concentrations and lower CO2 concentrations, whereas 02 showed negligible influence. A mathematical model for the sulfation of limestone involving chemical reaction at calcite grain surfaces and solid-state diffusion of carbonate...... ions in calcite grains is established. The validity of the model is limited to the initial sulfation period, in which nucleation of the solid product calcium sulphate is not started. This theoretical reaction-diffusion model gives a good simulation of the initial kinetics of the direct sulfation...

  20. Limestone attrition under simulated oxyfiring Fluidized-Bed combustion conditions

    Energy Technology Data Exchange (ETDEWEB)

    Scala, F. [Istituto di Ricerche sulla Combustione - CNR, Napoli (Italy); Salatino, P. [Dipartimento di Ingegneria Chimica - Universita degli Studi di Napoli Federico II, Napoli (Italy)

    2009-03-15

    Limestone attrition by surface wear was studied during the flue gas desulfurization under simulated fluidized-bed (FB) oxyfiring conditions and hindered calcination. Bench-scale experimental tests were carried out using well-established techniques previously developed for the characterization of sulfation and attrition of sorbents in air-blown atmospheric FB combustors. The experimental limestone conversion and attrition results were compared with those previously obtained with the same limestone under simulated air-blown combustion conditions. The differences in the conversion and attrition extents and patterns associated with oxyfiring as compared to air-blown atmospheric combustion were highlighted and related to the different particle morphologies and thicknesses of the sulfate layer. It was noted that attrition could play an important role in practical circulating FB combustor operation, by effectively enhancing particle sulfation under both oxyfiring and air-blown combustion conditions. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

  1. Characterization of limestone of region South and Southeast of Para

    International Nuclear Information System (INIS)

    Marinho, A.R.O.; Vieira, J.H.A.; Antunes Junior, L.V.; Medeiros, A.C.; Souza, G.P.

    2014-01-01

    Limestone is used in daily activities, and it is common the use of products containing calcium carbonate in various applications, from construction to food production, air purification to sewage treatment, the sugar refining materials for the toothpaste, the manufacture of glass and steel in the manufacture of paper, plastics, paints, ceramics and many others. The Limestone present in the region of south and southeast of Para is presented in deposits that have not been explored on a large scale, being justified a deepening in characteristics thereof. For the characterization of the material, gross samples were comminuted by crushing and ball mill, sieved and then separated into aliquots. In the end were used fluorescence analysis of X-ray, diffraction X-rays, determination of the moisture and loss on ignition of the material at 950 °C for one hour, obtaining results of a dolomitic limestone. (author)

  2. Landscape Visual Quality and Meiofauna Biodiversity on Sandy Beaches

    Science.gov (United States)

    Felix, Gabriela; Marenzi, Rosemeri C.; Polette, Marcos; Netto, Sérgio A.

    2016-10-01

    Sandy beaches are central economic assets, attracting more recreational users than other coastal ecosystems. However, urbanization and landscape modification can compromise both the functional integrity and the attractiveness of beach ecosystems. Our study aimed at investigating the relationship between sandy beach artificialization and the landscape perception by the users, and between sandy beach visual attractiveness and biodiversity. We conducted visual and biodiversity assessments of urbanized and semiurbanized sandy beaches in Brazil and Uruguay. We specifically examined meiofauna as an indicator of biodiversity. We hypothesized that urbanization of sandy beaches results in a higher number of landscape detractors that negatively affect user evaluation, and that lower-rated beach units support lower levels of biodiversity. We found that urbanized beach units were rated lower than semiurbanized units, indicating that visual quality was sensitive to human interventions. Our expectations regarding the relationship between landscape perception and biodiversity were only partially met; only few structural and functional descriptors of meiofauna assemblages differed among classes of visual quality. However, lower-rated beach units exhibited signs of lower environmental quality, indicated by higher oligochaete densities and significant differences in meiofauna structure. We conclude that managing sandy beaches needs to advance beyond assessment of aesthetic parameters to also include the structure and function of beach ecosystems. Use of such supporting tools for managing sandy beaches is particularly important in view of sea level rise and increasing coastal development.

  3. Effect of SO2 Dry Deposition on Porous Dolomitic Limestones

    Directory of Open Access Journals (Sweden)

    Florica Doroftei

    2010-01-01

    Full Text Available The present study is concerned with the assessment of the relative resistance of a monumental dolomitic limestone (Laspra – Spain used as building material in stone monuments and submitted to artificial ageing by SO2 dry deposition in the presence of humidity. To investigate the protection efficiency of different polymeric coatings, three commercially available siloxane-based oligomers (Lotexan-N, Silres BS 290 and Tegosivin HL 100 and a newly synthesized hybrid nanocomposite with silsesquioxane units (TMSPMA were used. A comparative assessment of the data obtained in this study underlines that a better limestone protection was obtained when treated with the hybrid nanocomposite with silsesquioxane units.

  4. Novel Hydroxyapatite Coatings for the Conservation of Marble and Limestone

    Science.gov (United States)

    Naidu, Sonia

    Marble and limestone are calcite-based materials used in the construction of various structures, many of which have significant artistic and architectural value. Unfortunately, due to calcite's high dissolution rate, these stones are susceptible to chemically-induced weathering in nature. Limestone, due to its inherent porosity, also faces other environmental weathering processes that cause weakening from disintegration at grain boundaries. The treatments presently available are all deficient in one way or another. The aim of this work is to examine the feasibility of using hydroxyapatite (HAP) as a novel protective coating for marble and limestone, with two goals: i) to reduce acid corrosion of marble and ii) to consolidate physically weathered limestone. The motivation for using HAP is its low dissolution rate and structural compatibility with calcite. Mild, wet chemical synthesis routes, in which inorganic phosphate-based solutions were reacted with marble and limestone, alone and with other precursors, were used to produce HAP films. Film nucleation, growth and phase evolution were studied on marble to understand film formation and determine the optimal synthesis route. An acid resistance test was developed to investigate the attack mechanism on marble and quantify the efficacy of HAP-based coatings. Film nucleation and growth were dependent on substrate surface roughness and increased with calcium and carbonate salt additions during synthesis. Acid attack on marble occurred via simultaneous dissolution at grain boundaries, twin boundaries and grain surfaces. HAP provided intermediate protection against acid attack, when compared to two conventional treatments. Its ability to protect the stone from acid was not as significant as predicted from dissolution kinetics and this was attributed to incomplete coverage and residual porosity within the film, arising from its flake-like crystal growth habit, which enabled acid to access the underlying substrate. The

  5. Oxic limestone drains for treatment of dilute, acidic mine drainage

    Science.gov (United States)

    Cravotta, Charles A.

    1998-01-01

    Limestone treatment systems can be effective for remediation of acidic mine drainage (AMD) that contains moderate concentrations of dissolved O2 , Fe3+ , or A13+ (1‐5 mg‐L‐1 ). Samples of water and limestone were collected periodically for 1 year at inflow, outflow, and intermediate points within underground, oxic limestone drains (OLDs) in Pennsylvania to evaluate the transport of dissolved metals and the effect of pH and Fe‐ and Al‐hydrolysis products on the rate of limestone dissolution. The influent was acidic and relatively dilute (pH 1 mg‐L‐1 ) but was near neutral (pH = 6.2‐7.0); Fe and Al decreased to less than 5% of influent concentrations. As pH increased near the inflow, hydrous Fe and Al oxides precipitated in the OLDs. The hydrous oxides, nominally Fe(OH)3 and AI(OH)3, were visible as loosely bound, orange‐yellow coatings on limestone near the inflow. As time elapsed, Fe(OH)3 and AI(OH)3 particles were transported downflow. During the first 6 months of the experiment, Mn 2+ was transported conservatively through the OLDs; however, during the second 6 months, concentrations of Mn in effluent decreased by about 50% relative to influent. The accumulation of hydrous oxides and elevated pH (>5) in the downflow part of the OLDs promoted sorption and coprecipitation of Mn as indicated by its enrichment relative to Fe in hydrous‐oxide particles and coatings on limestone. Despite thick (~1 mm) hydrous‐oxide coatings on limestone near the inflow, CaCO3 dissolution was more rapid near the inflow than at downflow points within the OLD where the limestone was not coated. The rate of limestone dissolution decreased with increased residence time, pH, and concentrations of Ca2+ and HCO3‐ and decreased PCO2. The following overall reaction shows alkalinity as an ultimate product of the iron hydrolysis reaction in an OLD:Fe2+ + 0.25 O2 +CaCO3 + 2.5 H2O --> Fe(OH)3 + 2 Ca2+ + 2 HCO3-where 2 moles of CaCO3 dissolve for each mole of Fe(OH)3 produced

  6. Sodium sesquicarbonate (Akang) and limestone as catalysts for the ...

    African Journals Online (AJOL)

    Production of monoglycerides from palm and palm kernel oils were carried out using sodium sesquicarbonate (akang) and lime stone as catalysts.The results showed that the maximum monoglyceride formed is in the range of 49–57% of the fatty product for the limestone catalyst and 78 – 92% for the sodium ...

  7. The Solnhofen Limestone: A stony heritage of many uses

    Science.gov (United States)

    Kölbl-Ebert, Martina; Kramar, Sabina; Cooper, Barry J.

    2016-04-01

    High above the valley of the River Altmühl (Bavaria, Germany), between Solnhofen to the west and Kelheim to the east, numerous quarries give access to thinly plated limestone from the Upper Jurassic, some 150 million years before the present. The main quarry areas lie around the town of Eichstätt and between the villages of Solnhofen, Langenaltheim and Mörnsheim. Here limestone slabs have been quarried for several hundred years, some even in Roman times. Solnhofen Limestone is famous worldwide; not only because it is a beautiful building stone of high quality, but also because of the exceptionally well-preserved fossils it contains -among them the early bird Archaeopteryx. The quarry industry between Solnhofen and Eichstätt has shaped a cultural landscape, with old and new quarries sunk into the plain and numerous spoil heaps rising above it, for the rock is not all economically useful. But many of the spoil heaps and the old quarries are environmentally protected as they provide a habitat for some rare plants and animals. It is not necessary to cut the Solnhofen Limestone with a saw: it is split by hand into thin and even slabs or sheets which are used for flagstones and wall covers, which since centuries are sold world-wide. Locally it also serves as roof tiles for traditional houses. Thick slabs of especially fine quality may be found near Solnhofen and Mörnsheim and are used for lithography printing.

  8. Effect of Limestone Powder on Microstructure of Ternary Cementitious System

    NARCIS (Netherlands)

    Zhang, Y.; Ye, G.

    2012-01-01

    The pressure to reach sustainability favours the development of ternary composite cement. The synergistic effect on mechanical behaviour at 28 days between limestone powder (LP) and pozzolanic additives, i.e. fly ash (FA) and blast furnace slag (BFS), has been documented. In order to better

  9. Kinetic Study of Calcination of Jakura Limestone Using Power Rate ...

    African Journals Online (AJOL)

    The calcination of Jakura limestone was also found to be first order reaction with respect to CaCO3 concentration having average regression coefficient of 0.99. The temperature dependent terms were found using Arrhenius law and it was observed that the reaction temperature has a direct effect on the rate of reaction.

  10. Limestone rocks analysis by X-ray fluorescence analysis

    International Nuclear Information System (INIS)

    Izquierdo M, G.; Ponce R, R.; Vazquez J, J.

    1996-01-01

    By request of a private company, employing basically X-ray fluorescence analysis (X RF), was established a fast and accurate method for the analysis of the major elements in limestone rocks. Additionally, for complementing analysis was determined by ion chromatography, the chlorides appearance and by atomic absorption of sodium. By gravimetry, was determined the losses by ignition and the alpha quartz. (Author)

  11. Hydrate Phase Assemblages in Calcium Sulfoaluminate - Metakaolin - Limestone Blends

    DEFF Research Database (Denmark)

    Pedersen, Malene Thostrup; Lothenbach, Barbara; Winnefeld, Frank

    2017-01-01

    The combination of a commercial calcium sulfoaluminate (CSA) cement with metakaolin (MK) and limestone (LS) as supplementary cementitious materials (SCMs) is investigated for a CSA replacement level of 20 wt%. In addition to a pure CSA cement, paste samples have been prepared for three blends wit...

  12. Flora of Chihuahuan desertscrub on limestone in northeastern Sonora, Mexico

    Science.gov (United States)

    Thomas R. Van Devender; Ana Lilia Reina-Guerrero; J. Jesus. Sanchez-Escalante

    2013-01-01

    Transects were done in desertscrub on limestone to characterize the flora of the westernmost Chihuahuan Desert. Most of the sites (15) were in the Municipios of Agua Prieta and Naco in northeastern Sonora, with single sites near Ascensión, northwestern Chihuahua and east of Douglas in southeastern Arizona. A total of 236 taxa were recorded on transects. Dicot perennial...

  13. Innovative Field Investigations in Limestone using a FACT-FLUTe

    DEFF Research Database (Denmark)

    Mosthaf, Klaus; Barrett Sørensen, Mie; Broholm, Mette Martina

    2015-01-01

    and the prevailing aqueous pore water concentrations for a range of hydraulic parameters and conditions typical for limestone aquifers. Results and outlook The sorption experiments showed very strong sorption with reasonably linear sorption isotherms over a very large concentration range for individual chlorinated...

  14. Hurricane Sandy: Rapid Response Imagery of the Surrounding Regions

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The imagery posted on this site is of Hurricane Sandy. The aerial photography missions were conducted by the NOAA Remote Sensing Division. The images were acquired...

  15. Macrofauna and meiofauna of two sandy beaches at Mombasa, Kenya

    Digital Repository Service at National Institute of Oceanography (India)

    Ansari, Z.A.; Ingole, B.S.; Parulekar, A.H.

    Macrofauna and meiofauna of 2 sandy beaches having medium and fine sand particles, respectively, were investigated, quantitatively Macrofauna density was highest around high water mark and progressively decreased towards low water mark Meiofauna...

  16. 2014 USGS CMGP Lidar: Sandy Restoration (Delaware and Maryland)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Geographic Extent: SANDY_Restoration_DE_MD_QL2 Area of Interest covers approximately 3.096 square miles. Lot #5 contains the full project area Dataset Description:...

  17. 2014 USGS CMGP Lidar: Post Sandy (Long Island, NY)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — TASK NAME: Long Island New York Sandy LIDAR lidar Data Acquisition and Processing Production Task USGS Contract No. G10PC00057 Task Order No. G14PD00296 Woolpert...

  18. Studies on Thiobacilli spp. isolated from sandy beaches of Kerala

    Digital Repository Service at National Institute of Oceanography (India)

    Gore, P.S.; Raveendran, O.; Unnithan, R.V.

    Occurrence, isolation and oxidative activity of Thiobacilli spp. from some sandy beaches of Kerala are reported. These organisms were encountered in polluted beaches and were dominant during monsoon in all the beaches...

  19. Model projections of atmospheric steering of Sandy-like superstorms.

    Science.gov (United States)

    Barnes, Elizabeth A; Polvani, Lorenzo M; Sobel, Adam H

    2013-09-17

    Superstorm Sandy ravaged the eastern seaboard of the United States, costing a great number of lives and billions of dollars in damage. Whether events like Sandy will become more frequent as anthropogenic greenhouse gases continue to increase remains an open and complex question. Here we consider whether the persistent large-scale atmospheric patterns that steered Sandy onto the coast will become more frequent in the coming decades. Using the Coupled Model Intercomparison Project, phase 5 multimodel ensemble, we demonstrate that climate models consistently project a decrease in the frequency and persistence of the westward flow that led to Sandy's unprecedented track, implying that future atmospheric conditions are less likely than at present to propel storms westward into the coast.

  20. On the Impact Angle of Hurricane Sandy's New Jersey Landfall

    Science.gov (United States)

    Hall, Timothy M.; Sobel, Adam H.

    2013-01-01

    Hurricane Sandy's track crossed the New Jersey coastline at an angle closer to perpendicular than any previous hurricane in the historic record, one of the factors contributing to recordsetting peak-water levels in parts of New Jersey and New York. To estimate the occurrence rate of Sandy-like tracks, we use a stochastic model built on historical hurricane data from the entire North Atlantic to generate a large sample of synthetic hurricanes. From this synthetic set we calculate that under long-term average climate conditions, a hurricane of Sandy's intensity or greater (category 1+) makes NJ landfall at an angle at least as close to perpendicular as Sandy's at an average annual rate of 0.0014 yr-1 (95% confidence range 0.0007 to 0.0023); i.e., a return period of 714 years (95% confidence range 435 to 1429).

  1. 0-6686 : improving DMS 9210 requirements for limestone rock asphalt : [project summary].

    Science.gov (United States)

    2013-08-01

    Limestone rock asphalt (LRA) mixtures have : been produced and placed for several decades : using specification requirements currently listed : under DMS 9210, Limestone Rock Asphalt (LRA). : Several Texas Department of Transportation : (TxDOT) distr...

  2. Assessment of Environmental Impacts of Limestone Quarrying Operations in Thailand

    Directory of Open Access Journals (Sweden)

    Kittipongvises Suthirat

    2017-11-01

    Full Text Available Environmental impacts of the mineral extraction have been a public concern. Presently, there is widespread global interest in the area of mining and its sustainability that focused on the need to shift mining industry to a more sustainable framework. The aim of this study was to systematically assess all possible environmental and climate change related impacts of the limestone quarrying operation in Thailand. By considering the life cycle assessment method, the production processes were divided into three phases: raw material extraction, transportation, and comminution. Both IMPACT 2002+ and the Greenhouse Gas Protocol methods were used. Results of IMPACT 2002+ analysis showed that per 1 ton crushed limestone rock production, the total depletion of resource and GHGs emissions were 79.6 MJ and 2.76 kg CO2 eq., respectively. Regarding to the four damage categories, ‘resources’ and ‘climate change’ categories were the two greatest environmental impacts of the limestone rock production. Diesel fuel and electricity consumption in the mining processes were the main causes of those impacts. For climate change, the unit of CO2 eq. was expressed to quantify the total GHGs emissions. Estimated result was about 3.13 kg CO2 eq. per ton limestone rock product. The results obtained by the Greenhouse Gas Protocol were also similar to IMPACT 2002+ method. Electrical energy consumption was considered as the main driver of GHGs, accounting for approximately 46.8 % of total fossil fuel CO2 emissions. A final point should be noted that data uncertainties in environmental assessment over the complete life cycle of limestone quarrying operation have to be carefully considered.

  3. Assessment of Environmental Impacts of Limestone Quarrying Operations in Thailand

    Science.gov (United States)

    Kittipongvises, Suthirat

    2017-11-01

    Environmental impacts of the mineral extraction have been a public concern. Presently, there is widespread global interest in the area of mining and its sustainability that focused on the need to shift mining industry to a more sustainable framework. The aim of this study was to systematically assess all possible environmental and climate change related impacts of the limestone quarrying operation in Thailand. By considering the life cycle assessment method, the production processes were divided into three phases: raw material extraction, transportation, and comminution. Both IMPACT 2002+ and the Greenhouse Gas Protocol methods were used. Results of IMPACT 2002+ analysis showed that per 1 ton crushed limestone rock production, the total depletion of resource and GHGs emissions were 79.6 MJ and 2.76 kg CO2 eq., respectively. Regarding to the four damage categories, `resources' and `climate change' categories were the two greatest environmental impacts of the limestone rock production. Diesel fuel and electricity consumption in the mining processes were the main causes of those impacts. For climate change, the unit of CO2 eq. was expressed to quantify the total GHGs emissions. Estimated result was about 3.13 kg CO2 eq. per ton limestone rock product. The results obtained by the Greenhouse Gas Protocol were also similar to IMPACT 2002+ method. Electrical energy consumption was considered as the main driver of GHGs, accounting for approximately 46.8 % of total fossil fuel CO2 emissions. A final point should be noted that data uncertainties in environmental assessment over the complete life cycle of limestone quarrying operation have to be carefully considered.

  4. Additional Gigantoproductus species from the upper Visean-Namurian limestone of Kotaki, central Japan

    OpenAIRE

    Ibaraki, Yousuke; Tazawa, Jun-ichi; Nakamura, Yukio

    2010-01-01

    A large productid brachiopod species, Gigantoproductus aurita (Bolkhovitinova, 1938), is described from the Tsuchikurazawa Limestone (upper Visean-Namurian), a large limestone block within a Permian accretionary complex of Kotaki, Itoigawa City, Niigata Prefecture, central Japan. This is the fourth described Gigantoproductus species from the Tsuchikurazawa Limestone. The range of G. aurita may extend to late Visean on the basis of the previous fossil records of the limestone.

  5. Reservoir architecture patterns of sandy gravel braided distributary channel

    Directory of Open Access Journals (Sweden)

    Senlin Yin

    2016-06-01

    Full Text Available The purpose of this study was to discuss shape, scale and superimposed types of sandy gravel bodies in sandy-gravel braided distributary channel. Lithofacies analysis, hierarchy bounding surface analysis and subsurface dense well pattern combining with outcrops method were used to examine reservoir architecture patterns of sandy gravel braided distributary channel based on cores, well logging, and outcrops data, and the reservoir architecture patterns of sandy gravel braided distributary channels in different grades have been established. The study shows: (1 The main reservoir architecture elements for sandy gravel braided channel delta are distributary channel and overbank sand, while reservoir flow barrier elements are interchannel and lacustrine mudstone. (2 The compound sand bodies in the sandy gravel braided delta distributary channel take on three shapes: sheet-like distributary channel sand body, interweave strip distributary channel sand body, single strip distributary channel sand body. (3 Identification marks of single distributary channel include: elevation of sand body top, lateral overlaying, “thick-thin-thick” feature of sand bodies, interchannel mudstone and overbank sand between distributary channels and the differences in well log curve shape of sand bodies. (4 Nine lithofacies types were distinguished in distributary channel unit interior, different channel units have different lithofacies association sequence.

  6. EAARL-B Coastal Topography--Eastern New Jersey, Hurricane Sandy, 2012: First Surface, Pre-Sandy

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — ASCII xyz and binary point-cloud data, as well as a digital elevation model (DEM) of a portion of the New Jersey coastline, pre- and post-Hurricane Sandy (October...

  7. Respirable dust and quartz exposure from three South African farms with sandy, sandy loam, and clay soils.

    Science.gov (United States)

    Swanepoel, Andrew J; Kromhout, Hans; Jinnah, Zubair A; Portengen, Lützen; Renton, Kevin; Gardiner, Kerry; Rees, David

    2011-07-01

    To quantify personal time-weighted average respirable dust and quartz exposure on a sandy, a sandy loam, and a clay soil farm in the Free State and North West provinces of South Africa and to ascertain whether soil type is a determinant of exposure to respirable quartz. Three farms, located in the Free State and North West provinces of South Africa, had their soil type confirmed as sandy, sandy loam, and clay; and, from these, a total of 298 respirable dust and respirable quartz measurements were collected between July 2006-November 2009 during periods of major farming operations. Values below the limit of detection (LOD) (22 μg · m(-3)) were estimated using multiple 'imputation'. Non-parametric tests were used to compare quartz exposure from the three different soil types. Exposure to respirable quartz occurred on all three farms with the highest individual concentration measured on the sandy soil farm (626 μg · m(-3)). Fifty-seven, 59, and 81% of the measurements on the sandy soil, sandy loam soil, and clay soil farm, respectively, exceeded the American Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value (TLV) of 25 μg · m(-3). Twelve and 13% of respirable quartz concentrations exceeded 100 μg · m(-3) on the sandy soil and sandy loam soil farms, respectively, but none exceeded this level on the clay soil farm. The proportions of measurements >100 μg · m(-3) were not significantly different between the sandy and sandy loam soil farms ('prop.test'; P = 0.65), but both were significantly larger than for the clay soil farm ('prop.test'; P = 0.0001). The percentage of quartz in respirable dust was determined for all three farms using measurements > the limit of detection. Percentages ranged from 0.5 to 94.4% with no significant difference in the median quartz percentages across the three farms (Kruskal-Wallis test; P = 0.91). This study demonstrates that there is significant potential for over-exposure to respirable quartz in

  8. Brazilian sandy beach macrofauna production: a review

    Directory of Open Access Journals (Sweden)

    Marcelo Petracco

    2012-12-01

    Full Text Available The state of the art of the studies on the production of Brazilian sandy beach macrofauna was analyzed on the basis of the data available in the literature. For this purpose, the representativeness of the production dataset was examined by latitudinal distribution, degree of exposure and morphodynamic state of beaches, taxonomic groups, and methods employed. A descriptive analysis was, further, made to investigate the trends in production of the more representative taxonomic groups and species of sandy beach macrofauna. A total of 69 macrofauna annual production estimates were obtained for 38 populations from 25 studies carried out between 22º56'S and 32º20'S. Production estimates were restricted to populations on beaches located on the southern and southeastern Brazilian coast. Most of the populations in the dataset inhabit exposed dissipative sandy beaches and are mainly represented by mollusks and crustaceans, with a smaller number of polychaetes. The trends in production among taxonomic groups follow a similar pattern to that observed on beaches throughout the world, with high values for bivalves and decapods. The high turnover rate (P/B ratio of the latter was due to the presence of several populations of the mole crab Emerita brasiliensis, which can attain high values of productivity, in the dataset. Most of the studies focus on the comparison of production and, especially, of P/B ratio according to life history traits in populations of the same species/taxonomic group. Despite the importance of life history-production studies, other approaches, such as the effect of man-induce disturbances on the macrofauna, should be undertaken in these threatened environments.O estado da arte dos estudos de produção da macrofauna de praias arenosas brasileiras foi analisado a partir de informações disponíveis na literatura. Para essa finalidade, a representatividade dos dados de produção foi examinada de acordo com a distribuição latitudinal

  9. Characterization of limestone reacted with acid-mine drainage in a pulsed limestone bed treatment system at the Friendship Hill National Historical Site, Pennsylvania, USA

    Science.gov (United States)

    Hammarstrom, J.M.; Sibrell, P.L.; Belkin, H.E.

    2003-01-01

    Armoring of limestone is a common cause of failure in limestone-based acid-mine drainage (AMD) treatment systems. Limestone is the least expensive material available for acid neutralization, but is not typically recommended for highly acidic, Fe-rich waters due to armoring with Fe(III) oxyhydroxide coatings. A new AMD treatment technology that uses CO2 in a pulsed limestone bed reactor minimizes armor formation and enhances limestone reaction with AMD. Limestone was characterized before and after treatment with constant flow and with the new pulsed limestone bed process using AMD from an inactive coal mine in Pennsylvania (pH = 2.9, Fe = 150 mg/l, acidity = 1000 mg/l CaCO3). In constant flow experiments, limestone is completely armored with reddish-colored ochre within 48 h of contact in a fluidized bed reactor. Effluent pH initially increased from the inflow pH of 2.9 to over 7, but then decreased to 6 during operation. Limestone removed from a pulsed bed pilot plant is a mixture of unarmored, rounded and etched limestone grains and partially armored limestone and refractory mineral grains (dolomite, pyrite). The ???30% of the residual grains in the pulsed flow reactor that are armored have thicker (50- to 100-??m), more aluminous coatings and lack the gypsum rind that develops in the constant flow experiment. Aluminium-rich zones developed in the interior parts of armor rims in both the constant flow and pulsed limestone bed experiments in response to pH changes at the solid/solution interface. ?? 2003 Elsevier Ltd. All rights reserved.

  10. Performance of portland limestone cements: Cements designed to be more sustainable that include up to 15% limestone addition

    Science.gov (United States)

    Barrett, Timothy J.

    In 2009, ASTM and AASHTO permitted the use of up to 5% interground limestone in ordinary portland cement (OPC) as a part of a change to ASTM C150/AASHTO M85. When this work was initiated a new proposal was being discussed that would enable up to 15% interground limestone cement to be considered in ASTM C595/AASHTO M234. This work served to provide rapid feedback to the state department of transportation and concrete industry for use in discussions regarding these specifications. Since the time this work was initiated, ASTM C595/AASHTO M234 was passed (2012c) and PLCs are now able to be specified, however they are still not widely used. The proposal for increasing the volume of limestone that would be permitted to be interground in cement is designed to enable more sustainable construction, which may significantly reduce the CO2 that is embodied in the built infrastructure while also extending the life of cement quarries. Research regarding the performance of cements with interground limestone has been conducted by the cement industry since these cements became widely used in Europe over three decades ago, however this work focuses on North American Portland Limestone Cements (PLCs) which are specifically designed to achieve similar performance as the OPCs they replace.This thesis presents a two-phase study in which the potential for application of cements containing limestone was assessed. The first phase of this study utilized a fundamental approach to determine whether cement with up to 15% of interground or blended limestone can be used as a direct substitute to ordinary portland cement. The second phase of the study assessed the concern of early age shrinkage and cracking potential when using PLCs, as these cements are typically ground finer than their OPC counterparts. For the first phase of the study, three commercially produced PLCs were obtained and compared to three commercially produced OPCs made from the same clinker. An additional cement was tested

  11. Are the Vinjamur rocks carbonatites or meta-limestones?

    Energy Technology Data Exchange (ETDEWEB)

    Subbarao, K V; Bhaskar Rao, B [Indian Institute of Technology, Bombay (India). Dept. of Earth Sciences; Le Bas, M J [Univ. of Leicester, Leicester (United Kingdom). Dept. of Geology

    1995-08-01

    New whole-rock rare earth element (REE) data for the metacarbonate rocks inter bedded with schists at Vinjamur in the Nellore schist belt of Andhra Pradesh, show low total REE contents ({sigma}9-128 ppm) that are inconsistent with an igneous carbonatitic origin but which correspond more closely with a sedimentary limestone origin. The REE data of these rocks however, do not give absolute discrimination between marbles of meta-limestone and metacarbonatite origin. Micro-probe analytical data give better discrimination, and the chemical compositions of the calcite, micas, amphibole, plagioclase, apatite, monazite and staurolite in the Vinjamur marbles give strong and consistent evidence of a metamorphosed sedimentary rather than an igneous origin. (author). 35 refs., 7 figs., 9 tabs.

  12. The influence of combustion derived pollutants on limestone deterioration

    DEFF Research Database (Denmark)

    Johnson, JB; Montgomery, Melanie; Thompson, GE

    1996-01-01

    This study concerns quantification of the relative chemical degradation effects of dry deposition of combustion-derived atmospheric pollutants, HCl, SO2 and NO2, on Portland and Monks Park limestones, employing laboratory exposure chambers for periods of 30 days. Using presentation rates up to 40 x...... 10(-4) mu g cm(-2) s(-1), the pollutants were assessed individually and in various combinations, along with ozone as oxidant, at 84% RH with dry or water-wetted surfaces. The degradation was followed by analysis of exposed stone, for Cl-, SO42- and NO3-, and of run-off solution for Ca2+, in addition...... to the anions. From these data, the total calcium released from limestone to reaction ions and products and the percentages of each pollutant reacted (and so the deposition velocity (V-D)) in each exposure regime were calculated. HCl acted independently of the presence of other pollutants, showed 40 and 100...

  13. Induration and Biot’s Coefficient of Palaeogene Limestone

    DEFF Research Database (Denmark)

    Andreassen, Katrine Alling

    2017-01-01

    In engineering geology and classification of rock masses for civil engineering purposes, the degree of induration for a rock serves as a useful classification parameter. Induration is a measure of how well the grains of a sedimentary rock are cemented together - from loosely cemented/soft rock...... to very competent/slightly metamorphic rock. The Biot coefficient links to the degree of cementation in the capacity of how it relates the elastic deformations with the change in pore pressure. A hypothesis is that the degree of induration could be correlated to the magnitude of the Biot coefficient....... This is tested on 11 Copenhagen Limestone specimens of varying porosity and densities obtained from one borehole with a limestone interval of 30 m. Their induration varies from H2 to H5. Elastic wave propagation measurements are used to establish the Biot coefficient and determination of the mineralogy for H5...

  14. Are the Vinjamur rocks carbonatites or meta-limestones?

    International Nuclear Information System (INIS)

    Subbarao, K.V.; Bhaskar Rao, B.; Le Bas, M.J.

    1995-01-01

    New whole-rock rare earth element (REE) data for the metacarbonate rocks inter bedded with schists at Vinjamur in the Nellore schist belt of Andhra Pradesh, show low total REE contents (σ9-128 ppm) that are inconsistent with an igneous carbonatitic origin but which correspond more closely with a sedimentary limestone origin. The REE data of these rocks however, do not give absolute discrimination between marbles of meta-limestone and metacarbonatite origin. Micro-probe analytical data give better discrimination, and the chemical compositions of the calcite, micas, amphibole, plagioclase, apatite, monazite and staurolite in the Vinjamur marbles give strong and consistent evidence of a metamorphosed sedimentary rather than an igneous origin. (author). 35 refs., 7 figs., 9 tabs

  15. OPTIMALIZATION OF BLASTING IN »LAKOVIĆI« LIMESTONE QUARRY

    OpenAIRE

    Branko Božić; Karlo Braun

    1992-01-01

    The optimalization of exploitation in »Lakovići« limestone quarry is described. Based on determined discontinuities in the rock mass and their densities, the best possible working site have been located in order to obtain the best possible sizes of blasted rocks and work slope stability. Optimal lowest resistance line size for the quarry has been counted and proved experimentally. New blasting parameters have resulted in considerable saving of drilling and explosive (the paper is published in...

  16. Degradation behavior of limestone concrete under limited time sodium exposure

    International Nuclear Information System (INIS)

    Das, S.K.; Sharma, A.K.; Ramesh, S.S.; Parida, F.C.; Kasinathan, N.; Chellapandi, P.

    2009-01-01

    Adequate safety measures are taken during design, fabrication, construction and operation of liquid sodium cooled fast breeder reactor (FBR). However, possibility of sodium leak from secondary heat transport circuits of FBR has not been completely ruled out. In the areas housing sodium pipelines such as Steam Generator Building (SGB), spilled liquid sodium not only reacts with air causing fire but also interacts with structural concrete resulting in its degradation. The structural concrete can be protected from sodium attack using sodium resistant sacrificial concrete layer or steel/refractory liners. Moreover, design and construction of sloping floor with sodium collection pit helps in minimizing the mass of sodium accumulated on the floor and exposure period. Sacrificial concrete layer on the structural concrete should meet key factors like economy, castability, easy removal of affected concrete in the event of a sodium fire and disposability of debris apart from its good resistance against hot burning sodium. Present study is directed towards testing of limestone concrete blocks (made out of 13% ordinary portland cement, 8% water, 48% coarse limestone and 31 % fine limestone aggregates)

  17. Adsorption of anionic surfactants in limestone medium during oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Canbolat, Serhat; Bagci, Suat [Middle East Technical Univ., Dept. of Petroleum and Natural Gas Engineering, Ankara (Turkey)

    2004-07-15

    Foam-forming surfactant performance was evaluated by several experimental methods (interfacial tension, foam stability, corefloods) using commercial surfactants. There is considerable interest in the use of foam-forming surfactants for mobility control in water flood. To provide effective mobility control, the injected surfactant must propagate from the injection well toward the production well. One of the important parameters affecting propagation of foam-forming surfactant through the reservoir is the retention of surfactant due to its adsorption on reservoir rock. The determination of the adsorption of foam-forming surfactants in limestone reservoirs is important for the residual oil recovery efficiency. Adsorption measurements, recovery efficiencies, and surfactant and alkaline flooding experiments carried out with the representative of the selected surfactants alkaline solutions, linear alkyl benzene sulphonic acid (LABSA), sodium lauryl ether sulfate (SLES), and NaOH in a limestone medium. These surfactants were selected with respect to their foaming ability. Calibration curves formed by pH measurements were used to determine the correct adsorption amount of the used surfactants and recovery efficiency of these surfactants compared with base waterflooding. The results showed that LABSA adsorbed more than SLES in limestone reservoirs. The recovery efficiency of SLES was higher than the recovery efficiency of LABSA, and they decreased the recovery efficiency with respect to only the water injection case. (Author)

  18. Development of gypsum alteration on marble and limestone

    Science.gov (United States)

    McGee, E.S.

    1996-01-01

    Blackened alteration crusts of gypsum plus particulates that form on sheltered areas on marble and limestone buildings pose a challenge for rehabilitation and cleaning. Fresh marble and limestone samples exposed at monitored exposure sites present conditions of simple geometry and well-documented exposures but have short exposure histories (one to five years). The gypsum alteration crusts that develop on these samples provide insight into the early stages and rate of alteration crust formation. Alteration crusts from buildings give a longer, but less well known exposure history and present much more complex surfaces for gypsum accumulation. Integrated observations and measurements of alteration crusts from exposure samples and from buildings identify four factors that are important in the formation and development of alteration crusts on marble and limestone: (1) pollution levels, (2) exposure to rain or washing, (3) geometry of exposure of the stone surface, and (4) permeability of the stone. The combination of these factors contributes to both the distribution and the physical characteristics of the gypsum crusts which may affect cleaning decisions.

  19. Biogenic magnetite as a primary remanence carrier in limestone deposits

    Science.gov (United States)

    Chang, Shih-Bin R.; Kirschvink, Joseph L.; Stolz, John F.

    1987-06-01

    Studies on the microbial communities and magnetic phases of samples collected from carbonate oozes at Sugarloaf Key, FL, U.S.A. and calcareous laminated sediments from Laguna Figueroa, Baja California, Mexico have revealed the existence of magnetotactic bacteria and ultrafine-grained single domain magnetite in both environments. Magnetotactic bacteria were identified by light and electron microscopy. The single domain magnetite was detected by coercivity spectra analysis with a SQUID magnetometer and examined under the transmission electron microscope. The similarity, in terms of size and shape, between the single domain magnetite found in these sediments and the magnetite observed in the bacterial magnetosome from enriched cultures indicates the ultrafine-grained magnetite in these two marine environments was biologically formed. These results, combined with the common occurrences of ultrafine-grained magnetite in limestone deposits detected rock magnetically, suggest biogenic magnetite may be present and contribute to the magnetic remanence in these rocks. Several Cambrian limestone samples, separately collected from Siberia, China, and Kazakhstan, were examined for the presence of bacterial magnetite. Samples from the Lower Cambrian Sinskian Formation at Siberia Platform were found to contain both a large amount of apparently bacterial magnetite particles and a very stable primary magnetic component. Post-Cambrian diagenesis does not seem to affect the microgranulometry of these apparently bacterial magnetite crystals or the magnetic remanence carried by them. Assessing the potential role of biogenic magnetite as a primary remanence carrier in other Phanerozoic limestone deposits ought to be further pursued.

  20. The Biot coefficient for a low permeability heterogeneous limestone

    Science.gov (United States)

    Selvadurai, A. P. S.

    2018-04-01

    This paper presents the experimental and theoretical developments used to estimate the Biot coefficient for the heterogeneous Cobourg Limestone, which is characterized by its very low permeability. The coefficient forms an important component of the Biot poroelastic model that is used to examine coupled hydro-mechanical and thermo-hydro-mechanical processes in the fluid-saturated Cobourg Limestone. The constraints imposed by both the heterogeneous fabric and its extremely low intact permeability [K \\in (10^{-23},10^{-20}) m2 ] require the development of alternative approaches to estimate the Biot coefficient. Large specimen bench-scale triaxial tests (150 mm diameter and 300 mm long) that account for the scale of the heterogeneous fabric are complemented by results for the volume fraction-based mineralogical composition derived from XRD measurements. The compressibility of the solid phase is based on theoretical developments proposed in the mechanics of multi-phasic elastic materials. An appeal to the theory of multi-phasic elastic solids is the only feasible approach for examining the compressibility of the solid phase. The presence of a number of mineral species necessitates the use of the theories of Voigt, Reuss and Hill along with the theories proposed by Hashin and Shtrikman for developing bounds for the compressibility of the multi-phasic geologic material composing the skeletal fabric. The analytical estimates for the Biot coefficient for the Cobourg Limestone are compared with results for similar low permeability rocks reported in the literature.

  1. Legal Considerations for Health Care Practitioners After Superstorm Sandy.

    Science.gov (United States)

    Hershey, Tina Batra; Van Nostrand, Elizabeth; Sood, Rishi K; Potter, Margaret

    2016-06-01

    During disaster response and recovery, legal issues often arise related to the provision of health care services to affected residents. Superstorm Sandy led to the evacuation of many hospitals and other health care facilities and compromised the ability of health care practitioners to provide necessary primary care. This article highlights the challenges and legal concerns faced by health care practitioners in the aftermath of Sandy, which included limitations in scope of practice, difficulties with credentialing, lack of portability of practitioner licenses, and concerns regarding volunteer immunity and liability. Governmental and nongovernmental entities employed various strategies to address these concerns; however, legal barriers remained that posed challenges throughout the Superstorm Sandy response and recovery period. We suggest future approaches to address these legal considerations, including policies and legislation, additional waivers of law, and planning and coordination among multiple levels of governmental and nongovernmental organizations. (Disaster Med Public Health Preparedness. 2016;10:518-524).

  2. Longitudinal Impact of Hurricane Sandy Exposure on Mental Health Symptoms.

    Science.gov (United States)

    Schwartz, Rebecca M; Gillezeau, Christina N; Liu, Bian; Lieberman-Cribbin, Wil; Taioli, Emanuela

    2017-08-24

    Hurricane Sandy hit the eastern coast of the United States in October 2012, causing billions of dollars in damage and acute physical and mental health problems. The long-term mental health consequences of the storm and their predictors have not been studied. New York City and Long Island residents completed questionnaires regarding their initial Hurricane Sandy exposure and mental health symptoms at baseline and 1 year later (N = 130). There were statistically significant decreases in anxiety scores (mean difference = -0.33, p Hurricane Sandy has an impact on PTSD symptoms that persists over time. Given the likelihood of more frequent and intense hurricanes due to climate change, future hurricane recovery efforts must consider the long-term effects of hurricane exposure on mental health, especially on PTSD, when providing appropriate assistance and treatment.

  3. Hurricane Sandy, Disaster Preparedness, and the Recovery Model.

    Science.gov (United States)

    Pizzi, Michael A

    2015-01-01

    Hurricane Sandy was the second largest and costliest hurricane in U.S. history to affect multiple states and communities. This article describes the lived experiences of 24 occupational therapy students who lived through Hurricane Sandy using the Recovery Model to frame the research. Occupational therapy student narratives were collected and analyzed using qualitative methods and framed by the Recovery Model. Directed content and thematic analysis was performed using the 10 components of the Recovery Model. The 10 components of the Recovery Model were experienced by or had an impact on the occupational therapy students as they coped and recovered in the aftermath of the natural disaster. This study provides insight into the lived experiences and recovery perspectives of occupational therapy students who experienced Hurricane Sandy. Further research is indicated in applying the Recovery Model to people who survive disasters. Copyright © 2015 by the American Occupational Therapy Association, Inc.

  4. Family Structures, Relationships, and Housing Recovery Decisions after Hurricane Sandy

    Directory of Open Access Journals (Sweden)

    Ali Nejat

    2016-04-01

    Full Text Available Understanding of the recovery phase of a disaster cycle is still in its infancy. Recent major disasters such as Hurricane Sandy have revealed the inability of existing policies and planning to promptly restore infrastructure, residential properties, and commercial activities in affected communities. In this setting, a thorough grasp of housing recovery decisions can lead to effective post-disaster planning by policyholders and public officials. The objective of this research is to integrate vignette and survey design to study how family bonds affected rebuilding/relocating decisions after Hurricane Sandy. Multinomial logistic regression was used to investigate respondents’ family structures before Sandy and explore whether their relationships with family members changed after Sandy. The study also explores the effect of the aforementioned relationship and its changes on households’ plans to either rebuild/repair their homes or relocate. These results were compared to another multinomial logistic regression which was applied to examine the impact of familial bonds on respondents’ suggestions to a vignette family concerning rebuilding and relocating after a hurricane similar to Sandy. Results indicate that respondents who lived with family members before Sandy were less likely to plan for relocating than those who lived alone. A more detailed examination shows that this effect was driven by those who improved their relationships with family members; those who did not improve their family relationships were not significantly different from those who lived alone, when it came to rebuilding/relocation planning. Those who improved their relationships with family members were also less likely to suggest that the vignette family relocate. This study supports the general hypothesis that family bonds reduce the desire to relocate, and provides empirical evidence that family mechanisms are important for the rebuilding/relocating decision

  5. 2012 U.S. Geological Survey Topographic Lidar: Northeast Atlantic Coast Post-Hurricane Sandy

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Binary point-cloud data were produced for a portion of the New York, Delaware, Maryland, Virginia, and North Carolina coastlines, post-Hurricane Sandy (Sandy was an...

  6. Kinetic Hydration Heat Modeling for High-Performance Concrete Containing Limestone Powder

    Directory of Open Access Journals (Sweden)

    Xiao-Yong Wang

    2017-01-01

    Full Text Available Limestone powder is increasingly used in producing high-performance concrete in the modern concrete industry. Limestone powder blended concrete has many advantages, such as increasing the early-age strength, reducing the setting time, improving the workability, and reducing the heat of hydration. This study presents a kinetic model for modeling the hydration heat of limestone blended concrete. First, an improved hydration model is proposed which considers the dilution effect and nucleation effect due to limestone powder addition. A degree of hydration is calculated using this improved hydration model. Second, hydration heat is calculated using the degree of hydration. The effects of water to binder ratio and limestone replacement ratio on hydration heat are clarified. Third, the temperature history and temperature distribution of hardening limestone blended concrete are calculated by combining hydration model with finite element method. The analysis results generally agree with experimental results of high-performance concrete with various mixing proportions.

  7. Simultaneous removal of several heavy metals from aqueous solution by natural limestones

    Directory of Open Access Journals (Sweden)

    Sdiri A.

    2014-07-01

    Full Text Available Four natural limestone samples, collected from the Campanian-Maastrichtian limestones, Tunisia, were used as adsorbents for the removal of toxic metals in aqueous systems. The results indicated that high removal efficiency could be achieved by the present natural limestones. Among the metal ions studied, Pb2+ was the most preferably removed cation because of its high affinity to calcite surface. In binary system, the presence of Cu2+ effectively depressed the sorption of Cd2+ and Zn2+. Similarly Cu2+ strongly competed with Pb2+ to limestone surface. In ternary system, the removal further decreased, but considerable amount of Pb2+ and Cu2+ still occurred regardless of the limestone sample. The same behavior was observed in quadruple system, where the selectivity sequence was Pb2+ > Cu2+ > Cd2+ > Zn2+. From these results, it was concluded that the studied limestones have the required technical specifications to be used for the removal of toxic metals from wastewaters.

  8. OPTIMALIZATION OF BLASTING IN »LAKOVIĆI« LIMESTONE QUARRY

    Directory of Open Access Journals (Sweden)

    Branko Božić

    1992-12-01

    Full Text Available The optimalization of exploitation in »Lakovići« limestone quarry is described. Based on determined discontinuities in the rock mass and their densities, the best possible working site have been located in order to obtain the best possible sizes of blasted rocks and work slope stability. Optimal lowest resistance line size for the quarry has been counted and proved experimentally. New blasting parameters have resulted in considerable saving of drilling and explosive (the paper is published in Croatian.

  9. Penetration of molten core materials into basaltic and limestone concrete

    International Nuclear Information System (INIS)

    Sutherland, H.J.

    1978-01-01

    In conjunction with the small-scale, melt-concrete interaction tests being conducted at Sandia Laboratories, an acoustic technique has been used to monitor the penetration of molten core materials into basaltic and limestone concrete. Real time plots of the position of the melt/concrete interface have been obtained, and they illustrate that the initial penetration rate of the melt may be of the order of 80 mm/min. Phenomena deduced by the technique include a non-wetted melt/concrete interface

  10. Patterns of species richness in sandy beaches of South America ...

    African Journals Online (AJOL)

    The middle shore is primarily occupied by cirolanids and bivalves, and hippid crabs, bivalves and amphipods dominate the lower beach. Generally, species richness increases from upper to lower beach levels. Studies carried out on exposed sandy beaches of south-central Chile (ca. 40°S) show that different beach states ...

  11. Hurricane Sandy: An Educational Bibliography of Key Research Studies

    Science.gov (United States)

    Piotrowski, Chris

    2013-01-01

    There, undoubtedly, will be a flurry of research activity in the "Superstorm" Sandy impact area on a myriad of disaster-related topics, across academic disciplines. The purpose of this study was to review the disaster research related specifically to hurricanes in the educational and social sciences that would best serve as a compendium…

  12. Structural stability and hydraulic conductivity of Nkpologu sandy ...

    African Journals Online (AJOL)

    vincent

    mean weight diameter (MWD), water dispersible silt (WDSi), aggregate size distributions (> 2 mm, 1-0.5 mm and < 0.25 ... above sea level. ... and red to brownish red and derived from sandy ... where Q = steady state volume of outflow from the.

  13. Aggregations of the sandy-beach isopod, Tylos granulatus ...

    African Journals Online (AJOL)

    ... lives as a scavenger in the intertidal zone of sandy beaches on the west coast of South Africa. Individuals emerge with the receding tide leaving exit holes, then forage for about two hours before returning to the vicinity of the high-water mark where they aggregate to bury themselves, leaving behind cone-shaped mounds.

  14. effect of tractor forward speed on sandy loam soil physical ...

    African Journals Online (AJOL)

    Dr Obe

    Ilorin on a sandy loam soil to evaluate the effect of the imposition of different .... of the blade is 10.5cm. ... arranged in an inverted cone shape with ... replicates were taken for each speed run. The ..... Thakur, T. C; A. Yadav; B. P. Varshney and.

  15. Structural Stability and Hydraulic Conductivity Of Nkpologu Sandy ...

    African Journals Online (AJOL)

    Studies were conducted in the runoff plots at the University of Nigeria Nsukka Teaching and Resesarch Farm in 2010 and 2011 to monitor the changes in structural stability and saturated hydraulic conductivity (Ksat) of Nkpologu sandy loam soil under different cover management practices. The management practices were ...

  16. Can porosity affect the hyperspectral signature of sandy landscapes?

    Science.gov (United States)

    Baranoski, Gladimir V. G.; Kimmel, Bradley W.

    2017-10-01

    Porosity is a fundamental property of sand deposits found in a wide range of landscapes, from beaches to dune fields. As a primary determinant of the density and permeability of sediments, it represents a central element in geophysical studies involving basin modeling and coastal erosion as well as geoaccoustics and geochemical investigations aiming at the understanding of sediment transport and water diffusion properties of sandy landscapes. These applications highlight the importance of obtaining reliable porosity estimations, which remains an elusive task, notably through remote sensing. In this work, we aim to contribute to the strengthening of the knowledge basis required for the development of new technologies for the remote monitoring of environmentally-triggered changes in sandy landscapes. Accordingly, we employ an in silico investigation approach to assess the effects of porosity variations on the reflectance of sandy landscapes in the visible and near-infrared spectral domains. More specifically, we perform predictive computer simulations using SPLITS, a hyperspectral light transport model for particulate materials that takes into account actual sand characterization data. To the best of our knowledge, this work represents the first comprehensive investigation relating porosity to the reflectance responses of sandy landscapes. Our findings indicate that the putative dependence of these responses on porosity may be considerably less pronounced than its dependence on other properties such as grain size and shape. Hence, future initiatives for the remote quantification of porosity will likely require reflectance sensors with a high degree of sensitivity.

  17. Rapid Assessment of Anthropogenic Impacts of Exposed Sandy ...

    African Journals Online (AJOL)

    We applied a rapid assessment methodology to estimate the degree of human impact of exposed sandy beaches in Ghana using ghost crabs as ecological indicators. The use of size ranges of ghost crab burrows and their population density as ecological indicators to assess extent of anthropogenic impacts on beaches ...

  18. Organisms associated with the sandy-beach bivalve Donax serra ...

    African Journals Online (AJOL)

    57: 134-136. BROWN, AC. & WEBB, S.c. 1994. Organisms associated \\.,.,ith burrowing whelks of the genus Bullia. S Afr. 1. Zool. 29: 144-151. BROWN, A.C., STENTON-DOZEY, J.~.E. & TRUEMAN, E.R.. 1989. Sandy-beach bivalves and gastropods; a comparison between Donax serra and Ruilia digitalis. Adv. mar. Bioi. 25:.

  19. Deaths associated with Hurricane Sandy - October-November 2012.

    Science.gov (United States)

    2013-05-24

    On October 29, 2012, Hurricane Sandy hit the northeastern U.S. coastline. Sandy's tropical storm winds stretched over 900 miles (1,440 km), causing storm surges and destruction over a larger area than that affected by hurricanes with more intensity but narrower paths. Based on storm surge predictions, mandatory evacuations were ordered on October 28, including for New York City's Evacuation Zone A, the coastal zone at risk for flooding from any hurricane. By October 31, the region had 6-12 inches (15-30 cm) of precipitation, 7-8 million customers without power, approximately 20,000 persons in shelters, and news reports of numerous fatalities (Robert Neurath, CDC, personal communication, 2013). To characterize deaths related to Sandy, CDC analyzed data on 117 hurricane-related deaths captured by American Red Cross (Red Cross) mortality tracking during October 28-November 30, 2012. This report describes the results of that analysis, which found drowning was the most common cause of death related to Sandy, and 45% of drowning deaths occurred in flooded homes in Evacuation Zone A. Drowning is a leading cause of hurricane death but is preventable with advance warning systems and evacuation plans. Emergency plans should ensure that persons receive and comprehend evacuation messages and have the necessary resources to comply with them.

  20. The Sandy Hook Elementary School shooting as tipping point

    Science.gov (United States)

    Shultz, James M; Muschert, Glenn W; Dingwall, Alison; Cohen, Alyssa M

    2013-01-01

    Among rampage shooting massacres, the Sandy Hook Elementary School shooting on December 14, 2012 galvanized public attention. In this Commentary we examine the features of this episode of gun violence that has sparked strong reactions and energized discourse that may ultimately lead toward constructive solutions to diminish high rates of firearm deaths and injuries in the United States. PMID:28228989

  1. Copper and zinc distribution coefficients for sandy aquifer materials

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Astrup, Thomas; Boddum, J. K.

    2000-01-01

    Distribution coe�cients (Kd) were measured for copper (Cu) and zinc (Zn) in laboratory batch experiments for 17 sandy aquifer materials at environmentally relevant solute concentrations (Cu: 5±300 mg/l, Zn: 20±3100 mg/l). The Kd values ranged two to three orders of magnitude (Cu: 70±10,800 l/ kg...

  2. The sandy beach meiofauna and free-living nematodes from De Panne (Belgium)

    OpenAIRE

    Gheskiere, T.; Hoste, E.; Kotwicki, L.; Degraer, S.; Vanaverbeke, J.; Vincx, M.

    2002-01-01

    Despite their rather barren and arid appearance, European sandy beaches harbour a highly diverse fauna and flora and some of them are even highly productive. In contrast to tropical sandy beaches little is known about the structural and functional diversity of the different benthic components. This study aims to investigate the structural diversity of the meiobenthos, emphasizing on free-living marine nematodes on a Belgian sandy beach.The samples were collected on the sandy beach of De Panne...

  3. Effects of soil amendment on soil characteristics and maize yield in Horqin Sandy Land

    Science.gov (United States)

    Zhou, L.; Liu, J. H.; Zhao, B. P.; Xue, A.; Hao, G. C.

    2016-08-01

    A 4-year experiment was conducted to investigate the inter-annual effects of sandy soil amendment on maize yield, soil water storage and soil enzymatic activities in sandy soil in Northeast China in 2010 to 2014. We applied the sandy soil amendment in different year, and investigated the different effects of sandy soil amendment in 2014. There were six treatments including: (1) no sandy soil amendment application (CK); (2) one year after applying sandy soil amendment (T1); (3) two years after applying sandy soil amendment(T2); (4) three years after applying sandy soil amendment(T3); (5)four years after applying sandy soil amendment(T4); (6) five years after applying sandy soil amendment (T5). T refers to treatment, and the number refers to the year after application of the sandy soil amendment. Comparing with CK, sandy soil amendments improved the soil water storage, soil urease, invertase, and catalase activity in different growth stages and soil layers, the order of soil water storage in all treatments roughly performed: T3 > T5 > T4 > T2 > T1 > CK. the order of soil urease, invertase, and catalase activity in all treatments roughly performed: T5 > T3 > T4 > T2 > T1 > CK. Soil application of sandy soil amendment significantly (p≤⃒0.05) increased the grain yield and biomass yield by 22.75%-41.42% and 29.92%-45.45% respectively, and maize yield gradually increased with the years go by in the following five years. Sandy soil amendment used in poor sandy soil had a positive effect on soil water storage, soil enzymatic activities and maize yield, after five years applied sandy soil amendment (T5) showed the best effects among all the treatments, and deserves further research.

  4. Coralgal facies of the Upper Eocene-Lower Oligocene limestones in Letca-Rastoci area

    Directory of Open Access Journals (Sweden)

    Ioana Prica

    2001-09-01

    Full Text Available In this paper are described the coralgal facies identified in the Upper Eocene-Lower Oligocene limestone succession (Cozla Formation outcropping in two quarries at Letca and Rastoci (Sălaj district, Romania. In the studied profiles the coral and algae limestones are interlayered with bioclastic limestones with foraminifera. On the top of relatively deep water deposits, coral and algae crusts and dendritic corals coated by algae were deposited. The environment registered a gradual deepening, the deposits being completely immersed, while bioclastic limestones with foraminifera were recurrently formed. This cycle is repeated, the whole succession being caracterized by several such “parasequences”.

  5. Modelling of Limestone Dissolution in Wet FGD Systems: The Importance of an Accurate Particle Size Distribution

    DEFF Research Database (Denmark)

    Kiil, Søren; Johnsson, Jan Erik; Dam-Johansen, Kim

    1999-01-01

    Danish limestone types with very different particle size distributions (PSDs). All limestones were of a high purity. Model predictions were found to be qualitatively in good agreement with experimental data without any use of adjustable parameters. Deviations between measurements and simulations were...... attributed primarily to the PSD measurements of the limestone particles, which were used as model inputs. The PSDs, measured using a laser diffrac-tion-based Malvern analyser, were probably not representative of the limestone samples because agglomeration phenomena took place when the particles were...

  6. Accelerated weathering of limestone for CO2 mitigation: Opportunities for the stone and cement industries

    Science.gov (United States)

    Langer, William H.; San, Juan A.; Rau, Greg H.; Caldeira, Ken

    2009-01-01

    Large amounts of limestone fines co-produced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point sources such as cement manufacturing. AWL reactants are readily available, inexpensive and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid. This reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate.

  7. Techniques for Source Zone and Plume Characterization of Tetrachloroethene in Fractured Limestone Aquifers

    DEFF Research Database (Denmark)

    Fjordbøge, Annika Sidelmann; Mosthaf, Klaus; Janniche, Gry S.

    Characterization of chlorinated solvents in fractured limestone aquifers is essential for proper development of site specific conceptual models and subsequent risk assessment and remediation. High resolution characterization is challenged by the difficulties involved in collection of intact core...... an improved conceptual understanding of contaminant transport. At both sites limestone cores were collected with significant core losses. The discrete quantification of chlorinated solvents in the retrieved limestone cores was compared to different FLUTe technologies at the DNAPL site and passive and active...... distribution compared to the data obtained by quantification of chlorinated solvents in the limestone cores....

  8. The effect of water on the sulphation of limestone

    Energy Technology Data Exchange (ETDEWEB)

    Chunbo Wang; Lufei Jia; Yewen Tan; E.J. Anthony [North China Electric Power University, Baoding City (China). School of Energy and Power Engineering

    2010-09-15

    A series of tests was conducted in a thermogravimetric analyzer (TGA) to study the sulphation behaviour of limestone in the presence of water over the temperature range of 800-850{sup o}C. Four different Canadian limestones, all with a particle size range of 75-425 {mu}m, were sulphated using a synthetic flue gas with a composition of 15% CO{sub 2}, 3% O{sub 2}, 0% or 10% H{sub 2}O, 1750 ppm SO{sub 2} and the balance N{sub 2}. Water was shown to have a significant promotional effect on sulphation, especially in the diffusion-controlled stage. However, the effect of water during the kinetic-controlled stage appeared to be much less pronounced. Based on these results, it is proposed that the presence of water leads to the transient formation of Ca(OH){sub 2} as an intermediate, which in turn reacts with SO{sub 2} at a faster rate than CaO does. Alternatively stated, it appears that H{sub 2}O acts as catalyst for the sulphation reaction of CaO. 30 refs., 8 figs., 3 tabs.

  9. Laser removal of water repellent treatments on limestone

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Heras, Miguel; Alvarez de Buergo, Monica; Rebollar, Esther; Oujja, Mohamed; Castillejo, Marta; Fort, Rafael

    2003-12-15

    Protective and water repellent treatments are applied on stone materials used on buildings or sculptures of artistic value to reduce water intrusion without limiting the natural permeability to water vapour of the material. The effect of the wavelength associated with the laser removal of two water repellent treatments applied on limestone, Paraloid B-72, a copolymer of methyl acrylate and ethyl methacrylate, and Tegosivin HL-100, a modified polysiloxane resin, was investigated by using the four harmonics of a Q-switched Nd:YAG laser (1064, 532, 355 and 266 nm). The modifications induced on the surface of limestone samples by laser irradiation were studied using colorimetry, roughness measurements and scanning electron microscopy (SEM). The removal of the treatments was found to be dependent on the laser irradiation conditions and on the characteristics of the coatings. The fundamental laser radiation was effective in removing both treatments, but thermal alteration processes were induced on the constituent calcite crystals. The best results were obtained by irradiation in the near UV at 355 nm.

  10. Rare earths in the Leadville Limestone and its marble derivates

    International Nuclear Information System (INIS)

    Jarvis, J.C.; Wildeman, T.R.; Banks, N.G.

    1975-01-01

    Samples of unaltered and metamorphosed Leadville Limestone (Mississippian, Colorado) were analyzed by neutron activation for ten rare-earth elements (REE). The total abundance of the REE in the least-altered limestone is 4-12 ppm, and their distribution patterns are believed to be dominated by the carbonate minerals. The abundances of the REE in the marbles and their sedimentary precursors are comparable but the distribution patterns are not. Eu is enriched over the other REE in the marbles, and stratigraphically upward in the formation (samples located progressively further from the heat source), the light REE become less enriched relative to the heavy REE. The Eu anomaly is attributed to its ability, unique among the REE, to change from the 3+ to 2+ oxidation state. Whether this results in preferential mobilization of the other REE or whether this reflects the composition of the pore fluid during metamorphism is unknown. Stratigraphically selective depletion of the heavy REE may be attributed to more competition for the REE between fluid and carbonate minerals in the lower strata relative to the upper strata. This competition could have been caused by changes in the temperature of the pore fluid or to the greater resistance to solution of the dolomite in the lower parts of the formation than the calcite in the upper parts

  11. Colmenar limestone as a resource for built heritage

    Science.gov (United States)

    Fort, Rafael; Álvarez de Buergo, Mónica; Varas-Muriel, MªJosé; Mercedes Pérez-Monserrat, Elena

    2013-04-01

    The Colmenar stone (or Colmenar limestone) has been used in the construction of significant builidings of the Central area of Spain, such as the Royal Palace of Aranjuez (16th -18th centuries) or the Royal Palace of Madrid (18th century). Nowadays this building stone is still widely used, both for new construction and restoration works, as well as for the indoor ornamentation of emblematic buildings such as the Royal Theater of Madrid (20th century). There are many quarries from where this stone was exploited, being the most prestigious ones those located in Colmenar de Oreja, at 50 km Southeast the city of Madrid. The high quality of the stone in these quarries, its whiteness and pureness, made this locality the most relevant in these stonés extractive activities, concentrating the most relevant exploitations and providing the stone the denomination of the municipality (Colmenar). It was an underground mining extraction until the 20th century in order to reach the highest quality level of the mine, the so called "Banco Gordo" (Thick Bank). Generically known as moorland limestone, this rock belongs to the fluvial-lacustrine carbonates of the Upper Miocene Unit of the Tertiary Madrid's Basin. Its tonality mainly ranges from white to cream and even light grey. Under a petrographic point of view, this limestone is constituted by 40% of bioclasts (characea, ostracods and gasteropods), 20-30% of micritic matrix and 30-40% of sparitic cement. Therefore, it can be classified as a biomicrite/biosparite limestone or as a bioclastic packstone. Some particularities of these limestones regarding their appearance are related to some karstic processes they underwent linked to some dissolution phenomena during the Pliocene. All of this resulted on an abundance of cavities with terra rossa fillings, a non-soluble clayey residue, iron enriched, which is the responsible for the reddish and pinkish color that the Colmenar stone sometimes shows. These petrographic characteristics

  12. Compressive strength evolution of thermally-stressed Saint Maximin limestone.

    Science.gov (United States)

    Farquharson, J.; Griffiths, L.; Baud, P.; Wadsworth, F. B.; Heap, M. J.

    2017-12-01

    The Saint Maximin quarry (Oise, France) opened in the early 1600s, and its limestone has been used extensively as masonry stone, particularly during the classical era of Parisian architecture from the 17th century onwards. Its widespread use has been due to a combination of its regional availability, its high workability, and its aesthetic appeal. Notable buildings completed using this material include sections of the Place de la Concorde and the Louvre in Paris. More recently, however, it has seen increasing use in the construction of large private residences throughout the United States as well as extensions to private institutions such as Stanford University. For any large building, fire hazard can be a substantial concern, especially in tectonically active areas where catastrophic fires may arise following large-magnitude earthquakes. Typically, house fires burn at temperatures of around 600 °C ( 1000 F). Given the ubiquity of this geomaterial as a building stone, it is important to ascertain the influence of heating on the strength of Saint Maximin limestone (SML), and in turn the structural stability of the buildings it is used in. We performed a series of compressive tests and permeability measurements on samples of SML to determine its strength evolution in response to heating to incrementally higher temperatures. We observe that the uniaxial compressive strength of SML decreases from >12 MPa at room temperature to 400 °C). We anticipate that this substantial weakening is in part a result of thermal microcracking, whereby changes in temperature induce thermal stresses due to a mismatch in thermal expansion between the constituent grains. This mechanism is compounded by the volumetric increase of quartz through its alpha - beta transition at 573 °C, and by the thermal decomposition of calcite. To track the formation of thermal microcracks, we monitor acoustic emissions, a common proxy for microcracking, during the heating of an SML sample. The

  13. Oriented nucleation and growth of anhydrite during direct sulfation of limestone

    DEFF Research Database (Denmark)

    Hu, Guilin; Dam-Johansen, Kim; Wedel, Stig

    2008-01-01

    The direct sulfation of limestone (Iceland Spar) was studied at 973 K in a fixed-bed reactor. Scanning electron microscopy examinations of the sulfated limestone particles show that the sulfation process involves oriented nucleation and growth of the solid product, anhydrite. The reason...

  14. Model for the sulfidation of calcined limestone and its use in reactor models.

    NARCIS (Netherlands)

    Heesink, Albertus B.M.; Brilman, Derk Willem Frederik; van Swaaij, Willibrordus Petrus Maria

    1998-01-01

    A mathematical model describing the sulfidation of a single calcined limestone particle was developed and experimentally verified. This model, which includes no fitting parameters, assumes a calcined limestone particle to consist of spherical grains of various sizes that react with H2S according to

  15. Development of engineered cementitious composites with limestone powder and blast furnace slag

    NARCIS (Netherlands)

    Zhou, J.; Qian, S.; Sierra Beltran, M.G.; Ye, G.; Van Breugel, K.; Li, V.C.

    2009-01-01

    Nowadays limestone powder and blast furnace slag (BFS) are widely used in concrete as blended materials in cement. The replacement of Portland cement by limestone powder and BFS can lower the cost and enhance the greenness of concrete, since the production of these two materials needs less energy

  16. LATEST TOURNAISIAN (EARLY CARBONIFEROUS CONODONTS FROM THE TABAI LIMESTONE, TIRAH, NORTHWESTERN PAKISTAN

    Directory of Open Access Journals (Sweden)

    FAZL-I-RABBI KHAN

    2004-11-01

    Full Text Available A new stratigraphic unit, the Tabai Limestone of the poorly known Tirah area of northwest Pakistan, is one of several Early Carboniferous carbonate units distributed along the North Gondwana margin, some connected with transgressive interludes. The Tabai Limestone has produced latest Tournaisian (Early Carboniferous conodonts indicative of the middle of the anchoralis-latus Zone.

  17. High Resolution Hydraulic Profiling and Groundwater Sampling using FLUTe™ System in a Fractured Limestone Setting

    DEFF Research Database (Denmark)

    Janniche, Gry Sander; Christensen, Anders G.; Grosen, Bernt

    challeng-ing in deposit types as fractured limestone. The activities of a bulk distribution facility for perchloroe-thene (PCE) and trichloroethene (TCE) at the Naverland site near Copenhagen, Denmark, has resulted in PCE and TCE DNAPL impacts to a fractured clay till and an underlying fractured limestone...

  18. STEAM ENHANCED REMEDIATION RESEARCH FOR DNAPL IN FRACTURED ROCK, LORING AIR FORCE BASE, LIMESTONE, MAINE

    Science.gov (United States)

    This report details a research project on Steam Enhanced Remediation (SER) for the recovery of volatile organic compounds from fractured limestone that was carried out at the Quarry at the former Loring Air Force Base in Limestone, Maine. This project was carried out by USEPA, Ma...

  19. Holocene limestones of part of the western continental shelf of India

    Digital Repository Service at National Institute of Oceanography (India)

    Nair, R.R.; Hashimi, N.H.; Guptha, M.V.S.

    , while those on te upper continental slope (130-180 m) are algal bryozoan limestones. The limestones have a radiocarbon age ranging between 9,000 and 11,000 years. Depositional environmental on the continental shelf during the Holocene appears...

  20. Evaluation of the Efficiency of Limestone Powder in Concrete and the Effects on the Environment

    Directory of Open Access Journals (Sweden)

    Yoo-Jae Kim

    2018-02-01

    Full Text Available The major environmental impact of concrete comes from the CO2 emissions, produced during the cement manufacturing process. The main goal of this research project is to evaluate the efficiency of limestone powder as a partial cement replacement, in order to reduce energy consumption and CO2 emissions. This study utilizes limestone powders, with different particle sizes, to replace a portion of Portland cement using various ratios. Due to the dilution effect when partially replacing cement, there is a reduction in the concrete’s physical properties. To assess the dilution effect, a modification to Féret’s equation is used to calculate an efficiency factor for the limestone powder when compared to cement. To measure the environmental impact, a life cycle assessment is conducted on concrete made with limestone powder combined with cement. This allows for an evaluation of the various cement/limestone powder ratios that will maximize the environmental benefit, with minimal reduction in concrete strength. Additional microstructural analysis using petrographic examination was completed to provide a visual understanding of the distribution of the limestone particles within the cement paste. The results indicate that the efficiency of limestone powder in partially replacing cement can be achieved by particle packing and particle distribution in the concrete and the benefits of emission reductions exceed the loss in compressive strength when higher levels of limestone powder is used to replace cement.

  1. Semiplanus (Productida, Brachiopoda) from the Carboniferous limestone of Kotaki, Niigata Prefecture, central Japan

    OpenAIRE

    Ibaraki, Yousuke; Sato, Kiichi

    2013-01-01

    An Early Carboniferous large–sized productid brachiopod species, Semiplanus semiplanus (Schwetzow, 1922), is described from the Tsuchikurazawa Limestone (upper Visean–Serpukhovian), a limestone block within a Permian accretionary complex, distributed in the Kotaki area, Itoigawa City, Niigata Prefecture, central Japan. This is the first record of Semipanus species from Japan.

  2. Adsorption and desorption of phosphate on limestone in experiments simulating seawater intrusion

    Science.gov (United States)

    The absorption and desorption of phosphorus on a large block of limestone was investigated using deionized water (DIW) and seawater. The limestone had a high affinity to adsorb phosphorus in DIW. Phosphate adsorption was significantly less in seawater, and more phosphorus was desorbed in the seawate...

  3. Effect of limestone particle size and calcium to non-phytate phosphorus ratio on true ileal calcium digestibility of limestone for broiler chickens.

    Science.gov (United States)

    Anwar, M N; Ravindran, V; Morel, P C H; Ravindran, G; Cowieson, A J

    2016-10-01

    The purpose of this study was to determine the effect of limestone particle size and calcium (Ca) to non-phytate phosphorus (P) ratio on the true ileal Ca digestibility of limestone for broiler chickens. A limestone sample was passed through a set of sieves and separated into fine (digestibility of Ca was calculated using the indicator method and corrected for basal endogenous losses to determine the true Ca digestibility. The basal ileal endogenous Ca losses were determined to be 127 mg/kg of dry matter intake. Increasing Ca:non-phytate P ratios reduced the true Ca digestibility of limestone. The true Ca digestibility coefficients of limestone with Ca:non-phytate P ratios of 1.5, 2.0 and 2.5 were 0.65, 0.57 and 0.49, respectively. Particle size of limestone had a marked effect on the Ca digestibility, with the digestibility being higher in coarse particles (0.71 vs. 0.43).

  4. Sorption and Migration Mechanisms of 237 Np through Sandy Soil

    International Nuclear Information System (INIS)

    Chantaraprachoom, Nanthavan; Tanaka, Tadao

    2003-06-01

    In order to evaluate migration behavior of radioactive nuclides in the disposal of low-level radioactive waste into a shallow land burial, the sorption characteristic and migration behavior of 237 Np through sandy soil was studied. Two experimental methods were performed by using batch and column systems. The distribution coefficients (K d ) obtained from the adsorption and desorption process are rather small about 16 and 21 cm 3 /g respectively. Size distribution of 237 Np species in the influent solution was measured by ultra-filtration technique. Migration mechanism of 237 Np was studied by column experiments. The experimental condition was the influence of volume of eluting solution; 100, 300, 500, 1000 and 2000 ml respectively. The result from five column experiments confirm that the sorption characteristics of 237 Np are mainly controlled by a reversible ion-exchange reaction and the migration of 237 Np in the sandy soil can be estimated by using the K d concept

  5. Superstorm Sandy and the Verdant Power RITE Project

    Science.gov (United States)

    Corren, D.; Colby, J.; Adonizio, M.

    2013-12-01

    On October 29, 2012 Superstorm Sandy (formerly Hurricane Sandy) made landfall in New Jersey. One of the deadliest, and second-costliest hurricane in US history, Sandy was the largest Atlantic hurricane on record, with a diameter of 1,800 km. It was this unprecedented size, extreme central low pressure, and full-moon timing that created a storm surge which inundated New York City with record-breaking water levels, resulting in tremendous destruction of buildings and infrastructure. At its RITE (Roosevelt Island Tidal Energy) Project in New York City's East River, Verdant Power has been installing demonstration and commercial turbine systems since 2005, along with performing related environmental monitoring and measurements. The RITE site is located in the East Channel of the East River, on the east side of Roosevelt Island. All along the East River, large areas of the adjacent boroughs were impacted by Sandy, including flooding of the subway tunnels under the river. When Sandy struck, Verdant had recently concluded a two-week in-water test at RITE of a new rotor for its Gen5 KHPS (Kinetic Hydropower System) turbine, with funding assistance by partners NYSERDA and the US Department of Energy. While the turbine had already been removed from its mounting in the river bottom in September, Verdant continued to operate two water measurement instruments in the river. These acoustic Doppler current profilers (ADCPs) measure the 3-D water velocity at various heights in the water column, and are also equipped to provide water level data. Verdant is interested in the effects such an extreme storm could have on turbines and other equipment installed in this river reach, as is planned by Verdant under a 10-year commercial pilot project licensed by the Federal Energy Regulatory Commission (FERC) for up to 30 turbines. Associated equipment includes navigational aids (buoys and signage), which Verdant is required to maintain to exclude vessels from the project boundaries. The East

  6. Quantifying the Digital Traces of Hurricane Sandy on Flickr

    Science.gov (United States)

    Preis, Tobias; Moat, Helen Susannah; Bishop, Steven R.; Treleaven, Philip; Stanley, H. Eugene

    2013-11-01

    Society's increasing interactions with technology are creating extensive ``digital traces'' of our collective human behavior. These new data sources are fuelling the rapid development of the new field of computational social science. To investigate user attention to the Hurricane Sandy disaster in 2012, we analyze data from Flickr, a popular website for sharing personal photographs. In this case study, we find that the number of photos taken and subsequently uploaded to Flickr with titles, descriptions or tags related to Hurricane Sandy bears a striking correlation to the atmospheric pressure in the US state New Jersey during this period. Appropriate leverage of such information could be useful to policy makers and others charged with emergency crisis management.

  7. Limestone fragmentation and attrition during fluidized bed oxyfiring

    Energy Technology Data Exchange (ETDEWEB)

    Fabrizio Scala; Piero Salatino [Istituto di Ricerche sulla Combustione - CNR, Napoli (Italy)

    2010-04-15

    Attrition/fragmentation of limestone under simulated fluidized bed oxyfiring conditions was investigated by means of an experimental protocol that had been previously developed for characterization of attrition/fragmentation of sorbents in air-blown atmospheric fluidized bed combustors. The protocol was based on the use of different and mutually complementary techniques. The extent and pattern of attrition by surface wear in the dense phase of a fluidized bed were assessed in experiments carried out with a bench scale fluidized bed combustor under simulated oxyfiring conditions. Sorbent samples generated during simulated oxyfiring tests were further characterized from the standpoint of fragmentation upon high velocity impact by means of a purposely designed particle impactor. Results showed that under calcination-hindered conditions attrition and fragmentation patterns are much different from those occurring under air-blown atmospheric combustion conditions. Noteworthy, attrition/fragmentation enhanced particle sulfation by continuously regenerating the exposed particle surface. 13 refs., 8 figs.

  8. Sierra Elvira limestone: petrophysical characteristics of an Andalusian heritage stone

    Directory of Open Access Journals (Sweden)

    Valverde, I.

    2008-06-01

    Full Text Available “Sierra Elvira stone” is one of the ornamental building stones most widely used in the historical monuments of eastern Andalusia. A Liassic age limestone, it appears in the central section of the Baetic Mountains and more specifically in the Middle Subbaetic domain. While the most common variety is a crinoid limestone, a micritic limestone of the same age has also been quarried, albeit in much smaller quantities. These stones form very thick beds, up to nearly 5 m deep, that run in consistently parallel lines and have a dip angle that facilitates quarrying.With petrographic, physical and mechanical properties that ensure stone strength and durability, it is a high quality building material suitable for both structural and ornamental purposes. These properties can be attributed to the minimal open porosity and concomitant excellent water resistance that characterize the stone, as well as to its high mechanical strength and low textural anisotropy, both elastic and mechanical. With such attributes, the stone can be successfully used for any number of purposes, including decorative stonework (portals, fountains, plinths, structural members (column shafts and bases or urban curbing and paving. Intervention on Sierra de Elvira limestone structures should be limited to cleaning or repair, for consolidating or protective materials are scantly effective.La “Piedra de Sierra Elvira” constituye una de las piedras ornamentales más significativas del Patrimonio Arquitectónico de Andalucía Oriental. Es una roca caliza del Lias que aflora en el Subbético Medio del sector central de las Cordilleras Béticas. El litotipo más explotado es una caliza con crinoides, en bastante menor importancia se ha extraído también otra caliza micrítica de la misma edad. Los bancos son muy potentes, en algunos casos de más de 5 m, con un paralelismo constante y un buzamiento que favorece su explotación en los frentes de cantera.Sus caracter

  9. Limestone-Concentrate-Pellet Roasting in wet Carbon Dioxide

    Institute of Scientific and Technical Information of China (English)

    1990-01-01

    A roast process for treating chalcopyrite concentrate was developed. The investigation of the reaction of limestone-concentrate-pellet in a wet carbon dioxide flow was carried out by means of a thermogravimetric analysis (TGA) to determine at which temperatures the roasting reaction would take place. The thermodynamic calculations on the roast reaction were made by the use of SOLGASMIX-PV program. The TGA curves and thermodynamic calculations indicated that the conversion of chalcopyrite into bornite took place at about 975K, and the conversion of bornite into chalcocite at 1065-1123K. The thermodynamic calculations also showed that the sulfur released was fixed as calcium sulfide within roasted pellets. X-ray diffraction examination identified these phases in products.

  10. Experienced materials in wet limestone-gypsum FGD system

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawa, S. [Mitsubishi Heavy Industry, Hiroshima (Japan). Hiroshima Research and Development Center; Iwashita, K.; Ochi, E.; Higuchi, T. [Mitsubishi heavy Industry, Yokohama (Japan)

    1998-12-31

    This study was made on the corrosion resistivity evaluation method used for material selection in the Wet Limestone-Gypsum FGD system with examples of various process configuration, their corrosion environment, and the materials used in them. The wet limestone-gypsum process FGD plant is broadly divided into two types-ash-separated (dual-loop) process, and ash-mixed (single-loop) process-depending on whether the flue gas is separated from ash before being led into the absorber or led as it is into the absorber mixed with ash. Presently, the single-loop process has become the mainstream process however. The dual -loop process comprises a dedusting tower (quencher) and an absorption tower (absorber). In the quencher ash is removed with sprayed water where most of the HCl, HF etc., and a part of SO{sub x} and NO{sub x} contained in the flue gas are also removed with absorption. On the contrary, in the single-loop process which is configured of only the absorber, the flue gas is introduced into it as it is contained with ash, SO{sub x}, NO{sub x}, HCl, HF etc. The corrosion environment in these plants largely differs depending on the process type and condition. The absorber recirculated liquid has various ion inclusions among which Cl{sup {minus}} promotes pitting corrosion and crevice corrosion while SO{sub 4}{sup 2{minus}} inhibits these corrosions. Both Cl{sup {minus}} and SO{sub 4}{sup 2{minus}} cover an extremely large range between 25 to 100,000 ppm and 564 to 73,600 ppm respectively, and their influence on the corrosion is related to their activity which is decided by Ca{sup 2+}, Mg{sup 2+}, Na{sup +}, NH{sub 4}{sup +}, H{sup +} and liquid temperature. The balance of these ions is decided by the gas composition, limestone composition, make-up water and wastewater mass balance etc., of individual plants. Accordingly, materials of FGD plant are selected on the basis of evaluated results of corrosion resistivity test made under such simulated process conditions of

  11. SLAM: a sodium-limestone concrete ablation model

    International Nuclear Information System (INIS)

    Suo-Anttila, A.J.

    1983-12-01

    SLAM is a three-region model, containing a pool (sodium and reaction debris) region, a dry (boundary layer and dehydrated concrete) region, and a wet (hydrated concrete) region. The model includes a solution to the mass, momentum, and energy equations in each region. A chemical kinetics model is included to provide heat sources due to chemical reactions between the sodium and the concrete. Both isolated model as well as integrated whole code evaluations have been made with good results. The chemical kinetics and water migration models were evaluated separately, with good results. Several small and large-scale sodium limestone concrete experiments were simulated with reasonable agreement between SLAM and the experimental results. The SLAM code was applied to investigate the effects of mixing, pool temperature, pool depth and fluidization. All these phenomena were found to be of significance in the predicted response of the sodium concrete interaction. Pool fluidization is predicted to be the most important variable in large scale interactions

  12. How hydrological factors initiate instability in a model sandy slope

    OpenAIRE

    Terajima, Tomomi; Miyahira, Ei-ichiro; Miyajima, Hiroyuki; Ochiai, Hirotaka; Hattori, Katsumi

    2013-01-01

    Knowledge of the mechanisms of rain-induced shallow landslides can improve the prediction of their occurrence and mitigate subsequent sediment disasters. Here, we examine an artificial slope's subsurface hydrology and propose a new slope stability analysis that includes seepage force and the down-slope transfer of excess shear forces. We measured pore water pressure and volumetric water content immediately prior to a shallow landslide on an artificial sandy slope of 32°: The direction of the ...

  13. Sandy lower Gotherivian reservoirs in the south central Turkmeniya. [Siberia

    Energy Technology Data Exchange (ETDEWEB)

    Mavyyev, N.Ch.; Nedirov, B.R.

    1982-01-01

    Composition and capacitance-filtering properties of sandy rocks of the early Gotherivian age developed on the fields of Karadzhaulak and Cirili within the northeast slope of the Predkopetdag marginal trough and on areas of Dengli Bakharadok of the Bakharadok monocline are studied. These rocks are viewed as analogs of the gas-bearing Shatlyk level of the Murgabskiy Basin. They can be considered the main potential source of hydrocarbons on the studied territory. In the upper part of the lower Gotherivian, a level of sandy rocks is traced. Rocks represented by small-and average-grained red and light grey differences in sandstones of polymictic composition. The porosity of the sandstones is 20-22%, permeability is 200-500 mdarcy. Not only a similar stratigraphic position of the described sandstones in the lower Gotherivian was found, but also lithological common nature of the rocks. In the south central Turkmeniya one can isolate age analogs of the Shatlyk level, the main productive level of southeast Turkmeniya. The thickness of the sandy beds is from 17 to 45 m. The sandstones of the Karadzhaulak area have the best capacitance-filtering properties. Post sedimentation changes depend on the quantity and composition of the cement, influence of formation waters, and possibly thermobaric conditions of rock formation. The presence of sandy rocks with high collector properties in the cross section of the lower Gotherivian deposits in south central Turkmeniya should be considered in determining the objects for further prospecting and exploration. The areas of Kumbet and Karadzhaulak are primary.

  14. Patterns of species richness in sandy beaches of South America

    African Journals Online (AJOL)

    beaches with rdkctive and dissip:1tive characteristics (sensu. R eprodu ced by Sabin et G atew ay u n der licen ce gran ted by th e P u blish er (dated 2009). ... beach intertidal communities WaS reviewed, (b) location of len sam.!y beaches studied in south-central Chile, imd (c) location of two sandy beaches studied on the ...

  15. Geochemistry, environmental and provenance study of the Middle Miocene Leitha limestones (Central Paratethys)

    Science.gov (United States)

    Ali, Ahmed; Wagreich, Michael

    2017-06-01

    Mineralogical, major, minor, REE and trace element analyses of rock samples were performed on Middle Miocene limestones (Leitha limestones, Badenian) collected from four localities from Austria (Mannersdorf, Wöllersdorf, Kummer and Rosenberg quarries) and the Fertőrákos quarry in Hungary. Impure to pure limestones (i.e. limited by Al2O3 contents above or below 0.43 wt. %) were tested to evaluate the applicability of various geochemical proxies and indices in regard to provenance and palaeoenvironmental interpretations. Pure and impure limestones from Mannersdorf and Wöllersdorf (southern Vienna Basin) show signs of detrital input (REEs = 27.6 ± 9.8 ppm, Ce anomaly = 0.95 ± 0.1 and the presence of quartz, muscovite and clay minerals in impure limestones) and diagenetic influence (low contents of, e.g., Sr = 221 ± 49 ppm, Na is not detected, Ba = 15.6 ± 8.8 ppm in pure limestones). Thus, in both limestones the reconstruction of original sedimentary palaeoenvironments by geochemistry is hampered. The Kummer and Fertőrákos (Eisenstadt-Sopron Basin) comprise pure limestones (e.g., averages Sr = 571 ± 139 ppm, Na = 213 ± 56 ppm, Ba = 21 ± 4 ppm, REEs = 16 ± 3 ppm and Ce anomaly = 0.62 ± 0.05 and composed predominantly of calcite) exhibiting negligible diagenesis. Deposition under a shallow-water, well oxygenated to intermittent dysoxic marine environment can be reconstructed. Pure to impure limestones at Rosenberg-Retznei (Styrian Basin) are affected to some extent by detrital input and volcano-siliciclastic admixture. The Leitha limestones at Rosenberg have the least diagenetic influence among the studied localities (i.e. averages Sr = 1271 ± 261 ppm, Na = 315 ± 195 ppm, Ba = 32 ± 15 ppm, REEs = 9.8 ± 4.2 ppm and Ce anomaly = 0.77 ± 0.1 and consist of calcite, minor dolomite and quartz). The siliciclastic sources are characterized by immobile elemental ratios (i.e. La/Sc and Th/Co) which apply not only for the siliciclastics, but also for marls and

  16. Geochemistry, environmental and provenance study of the Middle Miocene Leitha limestones (Central Paratethys

    Directory of Open Access Journals (Sweden)

    Ali Ahmed

    2017-06-01

    Full Text Available Mineralogical, major, minor, REE and trace element analyses of rock samples were performed on Middle Miocene limestones (Leitha limestones, Badenian collected from four localities from Austria (Mannersdorf, Wöllersdorf, Kummer and Rosenberg quarries and the Fertőrákos quarry in Hungary. Impure to pure limestones (i.e. limited by Al2O3 contents above or below 0.43 wt. % were tested to evaluate the applicability of various geochemical proxies and indices in regard to provenance and palaeoenvironmental interpretations. Pure and impure limestones from Mannersdorf and Wöllersdorf (southern Vienna Basin show signs of detrital input (REEs = 27.6 ± 9.8 ppm, Ce anomaly = 0.95 ± 0.1 and the presence of quartz, muscovite and clay minerals in impure limestones and diagenetic influence (low contents of, e.g., Sr = 221 ± 49 ppm, Na is not detected, Ba = 15.6 ± 8.8 ppm in pure limestones. Thus, in both limestones the reconstruction of original sedimentary palaeoenvironments by geochemistry is hampered. The Kummer and Fertőrákos (Eisenstadt–Sopron Basin comprise pure limestones (e.g., averages Sr = 571 ± 139 ppm, Na = 213 ± 56 ppm, Ba = 21 ± 4 ppm, REEs = 16 ± 3 ppm and Ce anomaly = 0.62 ± 0.05 and composed predominantly of calcite exhibiting negligible diagenesis. Deposition under a shallow-water, well oxygenated to intermittent dysoxic marine environment can be reconstructed. Pure to impure limestones at Rosenberg–Retznei (Styrian Basin are affected to some extent by detrital input and volcano-siliciclastic admixture. The Leitha limestones at Rosenberg have the least diagenetic influence among the studied localities (i.e. averages Sr = 1271 ± 261 ppm, Na = 315 ± 195 ppm, Ba = 32 ± 15 ppm, REEs = 9.8 ± 4.2 ppm and Ce anomaly = 0.77 ± 0.1 and consist of calcite, minor dolomite and quartz. The siliciclastic sources are characterized by immobile elemental ratios (i.e. La/Sc and Th/Co which apply not only for the siliciclastics, but also

  17. Electrokinetically Enhanced Delivery for ERD Remediation of Chlorinated Ethenes in a Fractured Limestone Aquifer

    DEFF Research Database (Denmark)

    Broholm, Mette Martina; Hyldegaard, Bente Højlund; With Nedergaard, Lærke

    causing very long remediation timeframes. Electrokinetics (EK) offers some unique transport processes, which can potentially overcome the diffusion limitations in the matrix. A novel technology combines ERD and EK for enhanced delivery. The combined technology (EK-BIO) has shown promising results in clay....... Experimental work on EK-BIO in limestone was conducted in a laboratory setup with limestone cores. EK was demonstrated to be promising in establishing enhanced contact between the donor lactate, bacteria, and cis-DCE within the limestone matrix. Complete dechlorination is expected to take place in the matrix......, since back diffusion limitations in the limestone matrix are overcome. This is essential for the overall time perspective of a remediation in limestone aquifers....

  18. Toxicity of acid mine pit lake water remediated with limestone and phosphorus

    Energy Technology Data Exchange (ETDEWEB)

    Neil, L.L.; McCullough, C.D.; Lund, M.A.; Evans, L.H.; Tsvetnenko, Y. [Edith Cowan University, Joondalup, WA (Australia)

    2009-11-15

    Pit lakes are increasingly common worldwide and have potential to provide many benefits. However, lake water toxicity may require remediation before beneficial end uses can be realised. Three treatments to remediate AMD (pH similar to 4.8) pit lake water containing elevated concentrations of Al and Zn from Collie, Western Australia were tested in mesocosms. Treatments were: (a) limestone neutralisation (L), (b) phosphorus amendment (P), and c) combined limestone neutralisation and phosphorus amendment (L+P). Laboratory bioassays with Ceriodaphnia cf. dubia, Chlorella protothecoides and Tetrahymena thermophila assessed remediation. Limestone neutralisation increased pH and reduced heavy metal concentrations by 98% (Al) to 14% (Mg), removing toxicity to the three test species within 2 months. Phosphorus amendment removed toxicity after 6 months of treatment. However, phosphorus amendment to prior limestone neutralisation failed to reduce toxicity more than limestone neutralisation alone. Low concentrations of both phosphorus and nitrogen appear to limit phytoplankton population growth in all treatments.

  19. Toxicity of acid mine pit lake water remediated with limestone and phosphorus.

    Science.gov (United States)

    Neil, Luke L; McCullough, Clint D; Lund, Mark A; Evans, Louis H; Tsvetnenko, Yuri

    2009-11-01

    Pit lakes are increasingly common worldwide and have potential to provide many benefits. However, lake water toxicity may require remediation before beneficial end uses can be realised. Three treatments to remediate AMD (pH approximately 4.8) pit lake water containing elevated concentrations of Al and Zn from Collie, Western Australia were tested in mesocosms. Treatments were: (a) limestone neutralisation (L), (b) phosphorus amendment (P), and (c) combined limestone neutralisation and phosphorus amendment (L+P). Laboratory bioassays with Ceriodaphnia cf. dubia, Chlorella protothecoides and Tetrahymena thermophila assessed remediation. Limestone neutralisation increased pH and reduced heavy metal concentrations by 98% (Al) to 14% (Mg), removing toxicity to the three test species within 2 months. Phosphorus amendment removed toxicity after 6 months of treatment. However, phosphorus amendment to prior limestone neutralisation failed to reduce toxicity more than limestone neutralisation alone. Low concentrations of both phosphorus and nitrogen appear to limit phytoplankton population growth in all treatments.

  20. Hydration mechanisms of ternary Portland cements containing limestone powder and fly ash

    International Nuclear Information System (INIS)

    De Weerdt, K.; Haha, M. Ben; Le Saout, G.; Kjellsen, K.O.; Justnes, H.; Lothenbach, B.

    2011-01-01

    The effect of minor additions of limestone powder on the properties of fly ash blended cements was investigated in this study using isothermal calorimetry, thermogravimetry (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM) techniques, and pore solution analysis. The presence of limestone powder led to the formation of hemi- and monocarbonate and to a stabilisation of ettringite compared to the limestone-free cements, where a part of the ettringite converted to monosulphate. Thus, the presence of 5% of limestone led to an increase of the volume of the hydrates, as visible in the increase in chemical shrinkage, and an increase in compressive strength. This effect was amplified for the fly ash/limestone blended cements due to the additional alumina provided by the fly ash reaction.

  1. Optimisation of a wet FGD pilot plant using fine limestone and organic acids

    DEFF Research Database (Denmark)

    Frandsen, Jan; Kiil, Søren; Johnsson, Jan Erik

    2001-01-01

    , but the residual limestone content in the gypsum increased to somewhere between 19 and 30 wt%, making this pH range unsuitable for use in a full-scale plant. The investigations have shown that both the addition of organic acids and the use of a limestone with a fine PSD can be used to optimise wet FGD plants. (C......The effects of adding an organic acid or using a limestone with a fine particle size distribution (PSD) have been examined in a wet flue gas desulphurisation (FGD) pilot plant. Optimisation of the plant with respect to the degree of desulphurisation and the residual limestone content of the gypsum...... has been the aim of the work. In contrast to earlier investigations with organic acids, all essential process parameters (i.e. gas phase concentration profiles of SO(2), slurry pH profiles. and residual limestone in the gypsum) were considered. Slurry concentrations of adipic acid in the range of 0...

  2. Brazilian sandy beaches: characteristics, ecosystem services, impacts, knowledge and priorities

    Directory of Open Access Journals (Sweden)

    Antonia Cecília Zacagnini Amaral

    Full Text Available ABSTRACT Sandy beaches constitute a key ecosystem and provide socioeconomic goods and services, thereby playing an important role in the maintenance of human populations and in biodiversity conservation. Despite the ecological and social importance of these ecosytems, Brazilian sandy beaches are significantly impacted by human interference, chemical and organic pollution and tourism, as well as global climate change. These factors drive the need to better understand the environmental change and its consequences for biota. To promote the implementation of integrated studies to detect the effects of regional and global environmental change on beaches and on other benthic habitats of the Brazilian coast, Brazilian marine researchers have established The Coastal Benthic Habitats Monitoring Network (ReBentos. In order to provide input for sample planning by ReBentos, we have conducted an intensive review of the studies conducted on Brazilian beaches and summarized the current knowledge about this environment. In this paper, we present the results of this review and describe the physical, biological and socioeconomics features of Brazilian beaches. We have used these results, our personal experience and worldwide literature to identify research projects that should be prioritized in the assessment of regional and global change on Brazilian sandy beaches. We trust that this paper will provide insights for future studies and represent a significant step towards the conservation of Brazilian beaches and their biodiversity.

  3. Modeling of Hydration, Compressive Strength, and Carbonation of Portland-Limestone Cement (PLC Concrete

    Directory of Open Access Journals (Sweden)

    Xiao-Yong Wang

    2017-01-01

    Full Text Available Limestone is widely used in the construction industry to produce Portland limestone cement (PLC concrete. Systematic evaluations of hydration kinetics, compressive strength development, and carbonation resistance are crucial for the rational use of limestone. This study presents a hydration-based model for evaluating the influences of limestone on the strength and carbonation of concrete. First, the hydration model analyzes the dilution effect and the nucleation effect of limestone during the hydration of cement. The degree of cement hydration is calculated by considering concrete mixing proportions, binder properties, and curing conditions. Second, by using the gel–space ratio, the compressive strength of PLC concrete is evaluated. The interactions among water-to-binder ratio, limestone replacement ratio, and strength development are highlighted. Third, the carbonate material contents and porosity are calculated from the hydration model and are used as input parameters for the carbonation model. By considering concrete microstructures and environmental conditions, the carbon dioxide diffusivity and carbonation depth of PLC concrete are evaluated. The proposed model has been determined to be valid for concrete with various water-to-binder ratios, limestone contents, and curing periods.

  4. Diversity and biogeography of land snails (Mollusca, Gastropoda) in the limestone hills of Perak, Peninsular Malaysia

    Science.gov (United States)

    Foon, Junn Kitt; Clements, Gopalasamy Reuben; Liew, Thor-Seng

    2017-01-01

    Abstract Limestone hills are now gaining global conservation attention as hotspots for short-range endemic species. Levels of land snail endemism can be high at limestone hills, especially at hill clusters that are geographically isolated. In the State of Perak, Peninsular Malaysia, limestone hills have been opportunistically surveyed for land snails in the past, but the majority have yet to be surveyed. To address this knowledge gap, we systematically surveyed the terrestrial malacofauna of 12 limestone hills that, based on our opinion, are a representation of the limestone land snail assemblages within the State. Our inventory yielded high sampling completeness (>85%). We found 122 species of land snails, of which 34 species were unique to one of the surveyed hills. We identified 30 species that are potentially new to science. The number of land snail species recorded at each hill ranged between 39 and 63 species. Four of the sampled limestone hills namely, Prk 01 G. Tempurung, Prk 55 G. Pondok, Prk 47 Kanthan, and Prk 64 Bt Kepala Gajah, have high levels of species richness and unique species, representing 91% of the total species recorded in this study. We identified two clusters of limestone hills in central Perak with distinct differences in land snail species composition – a northern hill cluster on elevated granite bedrock and southern hill cluster in a low-lying valley surrounded by alluvial soils. As limestone hills continue to be quarried to meet the cement demand, the four identified limestone hills, along with other hills from the two clusters, warrant urgent conservation attention in order to maintain high species diversity within Perak’s terrestrial malacofauna. PMID:28769723

  5. Preparation of Sandy Soil Stabilizer for Roads Based on Radiation Modified Polymer Composite

    International Nuclear Information System (INIS)

    Elnahas, H.H.

    2016-01-01

    Radiation modified polymer composite (RMPC) was studied to build an extremely durable sandy road, construct a trail or bath, or control dust and erosion. A dilute solution of composite binds sandy soil fines through a coagulation bonding process. The result is a dense soil structure that has superior resistance to cracks and water penetration and can also solve erosion control problems. In erosion control applications, diluted composite is merely sprayed into sandy soil without compaction, effectively sealing the surface to prevent air-born dust or deterioration from erosion. The prepared composite has an elastic and melt-able film formation that imparts thermal compacting to the stabilized sandy soil after full dryness for sandy road leveling, repairing and restoration processes. The prepared composite is environmentally economical when compared with traditional sandy soil stabilizing (SSS) or sealing methods.

  6. Capture of SO2 by limestone in a 71 MWe pressurized fluidized bed boiler

    Directory of Open Access Journals (Sweden)

    Shimizu Tadaaki

    2003-01-01

    Full Text Available A 71 MWe pressurized fluidized bed coal combustor was operated. A wide variety of coals were burnt under fly ash recycle conditions. Limestone was fed to the combustor as bed material as well as sorbent. The emission of SO^ and limestone attrition rate were measured. A simple mathematical model of SO? capture by limestone with intermittent solid attrition was applied to the analysis of the present experimental results. Except for high sulfur fuel, the results of the present model agreed with the experimental results.

  7. CARBONIFEROUS CORALS AND CHAETETIDS FROM EXOTIC LIMESTONE BLOCK OF THE CRIMEA

    Directory of Open Access Journals (Sweden)

    VICTOR OGAR

    2015-11-01

    Full Text Available A chaetetid sponge and coral fauna from a Carboniferous exotic limestone block in the Lower Jurassic Esciorda olistostrome on the Bodrak River (Crimean Mountains are described for the first time. The Bodrak exotic block is composed of massive limestone. It contains the chaetetid Chaetetes (Boswellia sp., the tabulate coral Multithecopora sp., and poorly preserved rugose corals, including Dibunophyllum? sp., Cordibia? sp. and gen. et sp. indet. Only the fasciculate colonies of the rugose coral Lytvophyllum askynensis (Kossovaya, 2009 are confidently identified. The studied association of fossils is similar to that of the Donets Basin and the Urals and confirms the Lower Bashkirian age of the Bodrak limestone block. 

  8. Online Media Use and Adoption by Hurricane Sandy Affected Fire and Police Departments

    OpenAIRE

    Chauhan, Apoorva

    2014-01-01

    In this thesis work, I examine the use and adoption of online communication media by 840 fire and police departments that were affected by the 2012 Hurricane Sandy. I began by exploring how and why these fire and police departments used (or did not use) online media to communicate with the public during Hurricane Sandy. Results show that fire and police departments used online media during Hurricane Sandy to give timely and relevant information to the public about things such as evacuations, ...

  9. Longitudinal Impact of Hurricane Sandy Exposure on Mental Health Symptoms

    Directory of Open Access Journals (Sweden)

    Rebecca M. Schwartz

    2017-08-01

    Full Text Available Hurricane Sandy hit the eastern coast of the United States in October 2012, causing billions of dollars in damage and acute physical and mental health problems. The long-term mental health consequences of the storm and their predictors have not been studied. New York City and Long Island residents completed questionnaires regarding their initial Hurricane Sandy exposure and mental health symptoms at baseline and 1 year later (N = 130. There were statistically significant decreases in anxiety scores (mean difference = −0.33, p < 0.01 and post-traumatic stress disorder (PTSD scores (mean difference = −1.98, p = 0.001 between baseline and follow-up. Experiencing a combination of personal and property damage was positively associated with long-term PTSD symptoms (ORadj 1.2, 95% CI [1.1–1.4] but not with anxiety or depression. Having anxiety, depression, or PTSD at baseline was a significant predictor of persistent anxiety (ORadj 2.8 95% CI [1.1–6.8], depression (ORadj 7.4 95% CI [2.3–24.1 and PTSD (ORadj 4.1 95% CI [1.1–14.6] at follow-up. Exposure to Hurricane Sandy has an impact on PTSD symptoms that persists over time. Given the likelihood of more frequent and intense hurricanes due to climate change, future hurricane recovery efforts must consider the long-term effects of hurricane exposure on mental health, especially on PTSD, when providing appropriate assistance and treatment.

  10. Constraining Depositional Slope From Sedimentary Structures in Sandy Braided Streams

    Science.gov (United States)

    Lynds, R. M.; Mohrig, D.; Heller, P. L.

    2003-12-01

    Determination of paleoslopes in ancient fluvial systems has potentially broad application to quantitatively constraining the history of tectonics and paleoclimate in continental sequences. Our method for calculating paleoslopes for sandy braided streams is based upon a simple physical model that establishes depositional skin-frictional shear stresses from assemblages of sedimentary structures and their associated grain size distributions. The addition of a skin-frictional shear stress, with a geometrically determined form-drag shear stress results in a total boundary shear stress which is directly related to water-surface slope averaged over an appropriate spatial scale. In order to apply this model to ancient fluvial systems, it is necessary to measure the following: coarsest suspended sediment size, finest grain size carried in bed load, flow depth, dune height, and dune length. In the rock record, suspended load and bed load can be accurately assessed by well-preserved suspended load deposits ("low-energy" ripples) and bed load deposits (dune foresets). This model predicts an average slope for the North Loup River near Taylor, Nebraska (modern case study) of 2.7 x 10-3. The measured reach-averaged water surface slope for the same reach of the river is 1.37 x 10-3. We suggest that it is possible to calculate the depositional slope of a sandy fluvial system by a factor of approximately two. Additionally, preliminary application of this model to the Lower Jurassic Kayenta Formation throughout the Colorado Plateau provides a promising and consistent evaluation of paleoslope in an ancient and well-preserved, sandy braided stream deposit.

  11. Disentangling diversity patterns in sandy beaches along environmental gradients.

    Science.gov (United States)

    Barboza, Francisco R; Gómez, Julio; Lercari, Diego; Defeo, Omar

    2012-01-01

    Species richness in sandy beaches is strongly affected by concurrent variations in morphodynamics and salinity. However, as in other ecosystems, different groups of species may exhibit contrasting patterns in response to these environmental variables, which would be obscured if only aggregate richness is considered. Deconstructing biodiversity, i.e. considering richness patterns separately for different groups of species according to their taxonomic affiliation, dispersal mode or mobility, could provide a more complete understanding about factors that drive species richness patterns. This study analyzed macroscale variations in species richness at 16 Uruguayan sandy beaches with different morphodynamics, distributed along the estuarine gradient generated by the Rio de la Plata over a 2 year period. Species richness estimates were deconstructed to discriminate among taxonomic groups, supralittoral and intertidal forms, and groups with different feeding habits and development modes. Species richness was lowest at intermediate salinities, increasing towards oceanic and inner estuarine conditions, mainly following the patterns shown for intertidal forms. Moreover, there was a differential tolerance to salinity changes according to the habitat occupied and development mode, which determines the degree of sensitivity of faunal groups to osmotic stress. Generalized (additive and linear) mixed models showed a clear increase of species richness towards dissipative beaches. All taxonomic categories exhibited the same trend, even though responses to grain size and beach slope were less marked for crustaceans and insects than for molluscs or polychaetes. However, supralittoral crustaceans exhibited the opposite trend. Feeding groups decreased from dissipative to reflective systems, deposit feeders being virtually absent in the latter. This deconstructive approach highlights the relevance of life history strategies in structuring communities, highlighting the relative

  12. The effects of Hurricane Sandy on trauma center admissions.

    Science.gov (United States)

    Curran, T; Bogdanovski, D A; Hicks, A S; Bilaniuk, J W; Adams, J M; Siegel, B K; DiFazio, L T; Durling-Grover, R; Nemeth, Z H

    2018-02-01

    Hurricane Sandy was a particularly unusual storm with regard to both size and location of landfall. The storm landed in New Jersey, which is unusual for a tropical storm of such scale, and created hazardous conditions which caused injury to residents during the storm and in the months following. This study aims to describe differences in trauma center admissions and patterns of injury during this time period when compared to a period with no such storm. Data were collected for this study from patients who were admitted to the trauma center at Morristown Medical Center during Hurricane Sandy or the ensuing cleanup efforts (patients admitted between 29 October 2012 and 27 December 2012) as well as a control group consisting of all patients admitted to the trauma center between 29 October 2013 and 27 December 2013. Patient information was collected to compare the admissions of the trauma center during the period of the storm and cleanup to the control period. A total of 419 cases were identified in the storm and cleanup period. 427 were identified for the control. Striking injuries were more common in the storm and cleanup group by 266.7% (p = 0.0107); cuts were more common by 650.8% (p = 0.0044). Medical records indicate that many of these injuries were caused by Hurricane Sandy. Self-inflicted injuries were more common by 301.3% (p = 0.0294). There were no significant differences in the total number of patients, mortality, or injury severity score between the two cohorts. The data we have collected show that the conditions caused by Hurricane Sandy and the following cleanup had a significant effect on injury patterns, with more patients having been injured by being struck by falling or thrown objects, cut while using tools, or causing self-inflicted injuries. These changes, particularly during the cleanup period, are indicative of environmental changes following the storm which increase these risks of injury.

  13. Dynamic compaction with high energy of sandy hydraulic fills

    Directory of Open Access Journals (Sweden)

    Khelalfa Houssam

    2017-09-01

    Full Text Available A case study about the adoption of the dynamic compaction technique with high energy in a sandy hydraulic fill is presented. The feasibility of this technique to ensure the stability of the caisson workshop and to minimize the risk of liquefaction during manufacture. This Article is interested to establish diagnostic of dynamic compaction test, basing on the results of SPT tests and quality control as well as the details of work of compaction and the properties of filling materials. A theory of soil response to a high-energy impact during dynamic compaction is proposed.

  14. Uncertainties in sandy shorelines evolution under the Bruun rule assumption

    Directory of Open Access Journals (Sweden)

    Gonéri eLe Cozannet

    2016-04-01

    Full Text Available In the current practice of sandy shoreline change assessments, the local sedimentary budget is evaluated using the sediment balance equation, that is, by summing the contributions of longshore and cross-shore processes. The contribution of future sea-level-rise induced by climate change is usually obtained using the Bruun rule, which assumes that the shoreline retreat is equal to the change of sea-level divided by the slope of the upper shoreface. However, it remains unsure that this approach is appropriate to account for the impacts of future sea-level rise. This is due to the lack of relevant observations to validate the Bruun rule under the expected sea-level rise rates. To address this issue, this article estimates the coastal settings and period of time under which the use of the Bruun rule could be (invalidated, in the case of wave-exposed gently-sloping sandy beaches. Using the sedimentary budgets of Stive (2004 and probabilistic sea-level rise scenarios based on IPCC, we provide shoreline change projections that account for all uncertain hydrosedimentary processes affecting idealized coasts (impacts of sea-level rise, storms and other cross-shore and longshore processes. We evaluate the relative importance of each source of uncertainties in the sediment balance equation using a global sensitivity analysis. For scenario RCP 6.0 and 8.5 and in the absence of coastal defences, the model predicts a perceivable shift toward generalized beach erosion by the middle of the 21st century. In contrast, the model predictions are unlikely to differ from the current situation in case of scenario RCP 2.6. Finally, the contribution of sea-level rise and climate change scenarios to sandy shoreline change projections uncertainties increases with time during the 21st century. Our results have three primary implications for coastal settings similar to those provided described in Stive (2004 : first, the validation of the Bruun rule will not necessarily be

  15. Hospital emergency preparedness and response during Superstorm Sandy.

    Science.gov (United States)

    2015-01-01

    This article presents the findings of a report by the HHS Office of Inspector General (OIG) on the performance of 172 Medicare-certified hospitals in the New York Metropolitan Area before, during, and after Sandy. It makes recommendations on how to close gaps that were found in emergency planning and execution for a disaster of this magnitude. To download the complete 40-page report and a Podcast based on it, go to http://oig.hhs.gov/oei/ reports/oei-06-13-00260. asp.

  16. Remediation of Diesel Fuel Contaminated Sandy Soil using Ultrasonic Waves

    Directory of Open Access Journals (Sweden)

    Wulandari P.S.

    2010-01-01

    Full Text Available Ultrasonic cleaning has been used in industry for some time, but the application of ultrasonic cleaning in contaminated soil is just recently received considerable attention, it is a very new technique, especially in Indonesia. An ultrasonic cleaner works mostly by energy released from the collapse of millions of microscopic cavitations near the dirty surface. This paper investigates the use of ultrasonic wave to enhance remediation of diesel fuel contaminated sandy soil considering the ultrasonic power, soil particle size, soil density, water flow rate, and duration of ultrasonic waves application.

  17. Radon in the Creswell Crags Permian limestone caves

    International Nuclear Information System (INIS)

    Gillmore, G.K.; Phillips, P.S.; Denman, A.R.; Gilbertson, D.D.

    2002-01-01

    An investigation of radon levels in the caves of Creswell Crags, Derbyshire, an important Site of Special Scientific Interest (SSSI) shows that the Lower Magnesian Limestone (Permian) caves have moderate to raised radon gas levels (27-7800 Bq m -3 ) which generally increase with increasing distance into the caves from the entrance regions. This feature is partly explained in terms of cave ventilation and topography. While these levels are generally below the Action Level in the workplace (400 Bq m -3 in the UK), they are above the Action Level for domestic properties (200 Bq m -3 ). Creswell Crags has approximately 40,000 visitors per year and therefore a quantification of effective dose is important for both visitors and guides to the Robin Hood show cave. Due to short exposure times the dose received by visitors is low (0.0016 mSv/visit) and regulations concerning exposure are not contravened. Similarly, the dose received by guides is fairly low (0.4 mSv/annum) due in part to current working practice. However, the risk to researchers entering the more inaccessible areas of the cave system is higher (0.06 mSv/visit). This survey also investigated the effect of seasonal variations on recorded radon concentration. From this work summer to winter ratios of between 1.1 and 9.51 were determined for different locations within the largest cave system

  18. Environmental impact management during construction of the limestone project

    International Nuclear Information System (INIS)

    Windsor, D.C.

    1988-01-01

    The Limestone Generating Station is being constructed on the Nelson River in Northern Manitoba, and will consist of a 10 unit powerhouse, 5 gate concrete spillway and earthfill dam spanning the 1.5 km width of the Nelson River. Environmental concerns associated with the project included insufficient pre- and post-construction monitoring documenting resources present or magnitude of impacts, impacts on brook trout and lake sturgeon resources, wildlife habitat loss due to construction activities, destruction or disturbance of historic or archaeological sites, degradation of nearby water courses and fish habitat by aggregate removal, in-migration of construction personnel, and various other socio-economic impacts. An overview is provided of monitoring activities and results in the above areas, which involved numerous consultants and government agencies. The project administration and workers did not find the environmental programs, including inspection and enforcement activities, to be onerous or an impediment to the project. On the contrary, the environmental requirements assisted in the general planning for certain activities, and in the general criteria for the conduct of the activities. The work permit process was particularly useful as it defined the requirements of both parties and provided the specific standards necessary determining the acceptability of the activities. 14 refs., 1 fig

  19. Transport studies of radon in limestone underlying houses

    International Nuclear Information System (INIS)

    Gammage, R.B.; Dudney, C.S.; Wilson, D.L.; Saultz, R.J.

    1990-01-01

    In hilly limestone terrains of the southern Appalachians, subterranean networks of solution cavities and fissures present circulatory systems facilitating convective and advective transport of radon-bearing gas. Evidence suggests that the primary driving forces for transport are aerostatic pressure differentials created by the difference between the underground and the outside air temperatures. Examples are presented of houses experiencing elevated indoor radon levels as a consequence of communicating with such subsurface transportation systems. The location of a house near the upper or lower end of a subterranean-circulatory system seems to produce amplification of indoor radon levels in winter or summer, respectively. The transport mechanism for radon-bearing air in karst and its impact on indoor radon need better understanding, both in regard to evaluating the geographical prevalence of the phenomenon and the induced spatial and temporal effects that are possible. This paper reports field studies made at houses in karst regions at Oak Ridge, Tennessee, and Huntsville, Alabama. A primary radon-transport mechanism is advocated of ascending or descending subsurface columns of air whose flows are largely driven by aerostatic pressure gradients created by the inground-outdoor air temperature differentials. 5 refs., 5 figs., 1 tab

  20. Interaction and penetration of heated UO2 with limestone concrete

    International Nuclear Information System (INIS)

    Farhadieh, R.; Pedersen, D.R.; Purviance, R.; Carlson, N.

    1982-01-01

    To safeguard the environment against radiological releases, the major question of concern in PAHR safety assessment, following an HCDA, involves confinement and dilution of the molten core-debris. Significant to the study is the directional growth of the core-debris in the concrete foundation of the reactor building or the concrete below the reactor cavity. The real material experiments were carried out in the test apparatus shown. Casts of CRBRP limestone concrete were prepared in graphite cylinders, each having an internal diameter of 8.9 cm and a depth of 30.5 cm. The 17.8-cm-deep concrete samples were allowed to cure for at least 28 days. Experiments were conducted within two months of curing time. The cavity above concrete was packed with 3 kg of pure UO 2 particles (1 to 3 mm). A uranothermic mixture was placed on the top of UO 2 powder. Heating and possible melting of UO 2 was achieved resistively after the ignition of the thermite. Total experimental time was about 60 minutes, during which time a maximum electrical power input of 1.8 watts/gr was applied to the UO 2 . Three gas samples were taken at temperatures of 100, 600, and 950 0 C, measured in the plane of the No. 2 thermocouple. Selection of three temperatures were to study the amount and the type of gases released from different phases of concrete

  1. Hydration study of limestone blended cement in the presence of hazardous wastes containing Cr(VI)

    International Nuclear Information System (INIS)

    Trezza, M.A.; Ferraiuelo, M.F.

    2003-01-01

    Considering the increasing use of limestone cement manufacture, the present paper tends to characterize limestone behavior in the presence of Cr(VI). The research reported herein provides information regarding the effect of Cr(VI) from industrial wastes in the limestone cement hydration. The cementitious materials were ordinary Portland cement, as reference, and limestone blended cement. The hydration and physicomechanical properties of cementitious materials and the influence of chromium at an early age were studied with X-ray diffraction (XRD), infrared spectroscopy (FTIR), conductimetric and mechanical tests. Portland cement pastes with the addition of Cr(VI) were examined and leaching behavior with respect to water and acid solution were investigated. This study indicates that Cr(VI) modifies the rate and the components obtained during the cement hydration

  2. Limestones in Treinta y Tres district : Aerial photo of Jose P. Varela - Isla Patrulla

    International Nuclear Information System (INIS)

    Coronel, N.; Heinzen, W.

    1981-01-01

    This work brings information of fields and laboratory samples about the outcrop in Treinta y Tres district in the framework of limestones programme carried out jointly with I.G.U and BGR through the geological German mission

  3. Coated limestone as a filler for the production of PVC-products

    Directory of Open Access Journals (Sweden)

    Mihajlović Slavica

    2005-01-01

    Full Text Available The results of laboratory investigations of the possibility to obtain coated limestone for the production of PVC-products are presented in this paper. Limestone from the "Venčac" deposit (Aranđelovac, Serbia and Montenegro was used as the raw material. The investigations were carried out in two phases: obtaining the coated limestone and determination of the degree of coating. The results of the investigations showed that successful coating of the surface of the limestone particles with Ca-stearate (Ca-stearate content 3% was achieved in a vibro mill with rings and the obtained degree of coating was higher than 95%. The coating degree was determined in transmitted light by a polarization microscope applying the immersion method (water immersion.

  4. Systematic ichnology of microborings from the Cenozoic White Limestone Group, Jamaica, West Indies

    NARCIS (Netherlands)

    Blissett, D.J.; Pickerill, R.K.

    2007-01-01

    The Middle Eocene to Middle Miocene White Limestone Group of Jamaica contains a common and diverse, poorly to well-preserved microboring ichnofauna, namely Centrichnus eccentricus Bromley & Martinell, Curvichnus pediformis isp. nov., Dendrorete balani Tavernier, Campbell & Golubic, Dipatulichnus

  5. Improving DMS 9210 requirements for limestone rock asphalt : year one interim report.

    Science.gov (United States)

    2013-05-01

    Limestone Rock Asphalt (LRA) mixtures have been produced and placed for several decades using specification requirements currently listed under DMS 9210. Several Districts have had placement issues and premature failures at the beginning of 2010. The...

  6. Dolomitization in the diagenetic history of the Štramberg limestones

    Czech Academy of Sciences Publication Activity Database

    Lintnerová, O.; Knietl, M.; Reháková, D.; Skupien, P.; Vašíček, Zdeněk

    2008-01-01

    Roč. 34, 3/1 (2008), s. 191-192 ISSN 0138-0974 Institutional research plan: CEZ:AV0Z30860518 Keywords : Štramberk Limestone * dolomitization * dedolomitization Subject RIV: DB - Geology ; Mineralogy

  7. Origin of intraformational folds in the Jurassic Todilto Limestone, Ambrosia Lake uranium mining district, McKinley and Valencia counties, New Mexico

    Science.gov (United States)

    Green, M.W.

    1982-01-01

    The Todilto Limestone of Middle Jurassic age in the Ambrosia Lake uranium mining district of McKinley and Valencia Counties, New Mexico, is the host formation for numerous small- to medium-sized uranium deposits in joints, shear zones, and fractures within small- to large-scale intraformational folds. The folds probably were formed as a result of differential sediment loading when eolian sand dunes of the overlying Summerville Formation of Middle Jurassic age migrated over soft, chemically precipitated, lime muds of the Todilto shortly after their deposition in a regressive, mixed fresh and saline lacustrine or marine environment of deposition. Encroachment of Summerville eolian dunes over soft Todilto lime muds was apparently a local phenomenon and was restricted to postulated beltlike zones which trended radially across the Todilto coastline toward the receding body of water. Intraformational folding is believed to be confined to the pathways of individual eolian dunes or clusters of dunes within the dune belts. During the process of sediment loading by migrating sand dunes, layers of Todilto lime mud were differentially compacted, contorted, and dewatered, producing both small- and large-scale plastic deformation structures, including convolute laminations, mounds, rolls, folds, and small anticlines and synclines. With continued compaction and dewatering, the mud, in localized areas, reached a point of desaturation at which sediment plasticity was lost. Prolonged loading by overlying dune sands thus caused faulting, shearing, fracturing, and jointing of contorted limestone beds. These areas or zones of deformation within the limestone became the preferred sites of epigenetic uranium mineralization because of the induced transmissivity created by sediment rupture. Along most of the prograding Todilto coastline, adjacent to the eolian dune belts, both interdune and coastal sabkha environments dominated during Todilto-Summerville time. Sediments in coastal areas

  8. Quality Assurance After a Natural Disaster: Lessons from Hurricane Sandy.

    Science.gov (United States)

    Dickerson, Collin; Hsu, Yanshen; Mendoza, Sandra; Osman, Iman; Ogilvie, Jennifer; Patel, Kepal; Moreira, Andre L

    2018-04-01

    Biospecimen quality can vary depending on many pre- and post-collection variables. In this study, we consider a natural disaster as a post-collection variable that may have compromised the quality of frozen tissue specimens. To investigate this possible link, we compared the quality of nucleic acids, the level of antigenicity, and the preservation of histology from frozen specimens collected before and after the power outage caused by Hurricane Sandy. To analyze nucleic acid quality, we extracted both DNA and RNA and performed capillary electrophoresis to compare the quality and concentrations of the nucleic acids. To compare antigenicity, frozen sections were cut and immunostained for thyroid transcription factor 1 (TTF-1), a nuclear transcription protein commonly used as a diagnostic biomarker for multiple cancer types, including thyroid and lung cancers. Positive expression of TTF-1, as noted by homogenous nuclear staining, would demonstrate that the TTF-1 proteins could still bind antibodies and, therefore, that these proteins were not significantly degraded. Furthermore, representative frozen sections stained with hematoxylin and eosin were also assessed qualitatively by a trained pathologist to examine any possible histologic aberrations. Due to the similar quality of the tissue samples collected before and after the storm, Hurricane Sandy had no discernable effect on the quality of frozen specimens, and these specimens exposed to the natural disaster are still valuable research tools.

  9. Measurement of earthquake-induced shear strain in sandy gravel

    International Nuclear Information System (INIS)

    Ohkawa, I.; Futaki, M.; Yamanouchi, H.

    1989-01-01

    The nuclear power reactor buildings have been constructed on the hard rock ground formed in or before the Tertiary in Japan. This is mainly because the nuclear reactor building is much heavier than the common buildings and requires a large bearing capacity of the underlying soil deposit, and additionally the excessive deformation in soil deposit might cause damage in reactor building and subsequently cause the malfunction of the internal important facilities. Another reason is that the Quaternary soil deposit is not fully known with respect to its dynamic property. The gravel, and the sandy gravel, the representative soils of the Quaternary, have been believed to be suitable soil deposits to support the foundation of a common building, although the soils have rarely been investigated so closely on their physical properties quantitatively. In this paper, the dynamic deformability, i.e., the shear stress-strain relationship of the Quaternary diluvial soil deposit is examined through the earthquake ground motion measurement using accelerometers, pore-pressure meters, the specific devices developed in this research work. The objective soil deposit in this research is the sandy gravel of the diluvial and the alluvial

  10. Trophic niche shifts driven by phytoplankton in sandy beach ecosystems

    Science.gov (United States)

    Bergamino, Leandro; Martínez, Ana; Han, Eunah; Lercari, Diego; Defeo, Omar

    2016-10-01

    Stable isotopes (δ13C and δ15N) together with chlorophyll a and densities of surf diatoms were used to analyze changes in trophic niches of species in two sandy beaches of Uruguay with contrasting morphodynamics (i.e. dissipative vs. reflective). Consumers and food sources were collected over four seasons, including sediment organic matter (SOM), suspended particulate organic matter (POM) and the surf zone diatom Asterionellopsis guyunusae. Circular statistics and a Bayesian isotope mixing model were used to quantify food web differences between beaches. Consumers changed their trophic niche between beaches in the same direction of the food web space towards higher reliance on surf diatoms in the dissipative beach. Mixing models indicated that A. guyunusae was the primary nutrition source for suspension feeders in the dissipative beach, explaining their change in dietary niche compared to the reflective beach where the proportional contribution of surf diatoms was low. The high C/N ratios in A. guyunusae indicated its high nutritional value and N content, and may help to explain the high assimilation by suspension feeders at the dissipative beach. Furthermore, density of A. guyunusae was higher in the dissipative than in the reflective beach, and cell density was positively correlated with chlorophyll a only in the dissipative beach. Therefore, surf diatoms are important drivers in the dynamics of sandy beach food webs, determining the trophic niche space and productivity. Our study provides valuable insights on shifting foraging behavior by beach fauna in response to changes in resource availability.

  11. Superstorm Sandy and the academic achievement of university students.

    Science.gov (United States)

    Doyle, Matthew D; Lockwood, Brian; Comiskey, John G

    2017-10-01

    Much of the literature on the consequences of natural disasters has focused on their physical and psychological ramifications. Few researchers have considered how the impacts of a natural disaster can influence academic achievement. This study analyses data collected from nearly 300 students at a mid-sized, private university in the northeast United States to determine if the effects of Cyclone Sandy in 2012 are associated with measures of academic achievement. The findings reveal that experiencing headaches after the event resulted in a higher likelihood of students suffering a loss of academic motivation. In addition, experiencing headaches and a loss of academic motivation were correlated with a lower grade point average (GPA) during the semester in which Sandy made landfall. However, the more direct effects of the superstorm, including displacement and a loss of power, did not have a significant bearing on academic achievement. Lastly, the paper examines the implications for higher education policy and future research. © 2017 The Author(s). Disasters © Overseas Development Institute, 2017.

  12. Deterioration of limestone aggregate mortars by liquid sodium in fast breeder reactor environment

    Energy Technology Data Exchange (ETDEWEB)

    Mohammed Haneefa, K., E-mail: mhkolakkadan@gmail.com [Department of Civil Engineering, IIT Madras, Chennai (India); Santhanam, Manu [Department of Civil Engineering, IIT Madras, Chennai (India); Parida, F.C. [Radiological Safety Division, Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

    2014-08-15

    Highlights: • Limestone mortars were exposed to liquid sodium exposure at 550 °C. • Micro-analytical techniques were used to characterize the exposed specimens. • The performance of limestone mortar was greatly influenced by w/c. • The fundamental degradation mechanisms of limestone mortars were identified. - Abstract: Hot liquid sodium at 550 °C can interact with concrete in the scenario of an accidental spillage of sodium in liquid metal cooled fast breeder reactors. To protect the structural concrete from thermo-chemical degradation, a sacrificial layer of limestone aggregate concrete is provided over it. This study investigates the fundamental mechanisms of thermo-chemical interaction between the hot liquid sodium and limestone mortars at 550 °C for a duration of 30 min in open air. The investigation involves four different types of cement with variation of water-to-cement ratios (w/c) from 0.4 to 0.6. Comprehensive analysis of experimental results reveals that the degree of damage experienced by limestone mortars displayed an upward trend with increase in w/c ratios for a given type of cement. Performance of fly ash based Portland pozzolana cement was superior to other types of cements for a w/c of 0.55. The fundamental degradation mechanisms of limestone mortars during hot liquid sodium interactions include alterations in cement paste phase, formation of sodium compounds from the interaction between solid phases of cement paste and aggregate, modifications of interfacial transition zone (ITZ), decomposition of CaCO{sub 3}, widening and etching of rhombohedral cleavages, and subsequent breaking through the weakest rhombohedral cleavage planes of calcite, staining, ferric oxidation in grain boundaries and disintegration of impurity minerals in limestone.

  13. Deterioration of limestone aggregate mortars by liquid sodium in fast breeder reactor environment

    International Nuclear Information System (INIS)

    Mohammed Haneefa, K.; Santhanam, Manu; Parida, F.C.

    2014-01-01

    Highlights: • Limestone mortars were exposed to liquid sodium exposure at 550 °C. • Micro-analytical techniques were used to characterize the exposed specimens. • The performance of limestone mortar was greatly influenced by w/c. • The fundamental degradation mechanisms of limestone mortars were identified. - Abstract: Hot liquid sodium at 550 °C can interact with concrete in the scenario of an accidental spillage of sodium in liquid metal cooled fast breeder reactors. To protect the structural concrete from thermo-chemical degradation, a sacrificial layer of limestone aggregate concrete is provided over it. This study investigates the fundamental mechanisms of thermo-chemical interaction between the hot liquid sodium and limestone mortars at 550 °C for a duration of 30 min in open air. The investigation involves four different types of cement with variation of water-to-cement ratios (w/c) from 0.4 to 0.6. Comprehensive analysis of experimental results reveals that the degree of damage experienced by limestone mortars displayed an upward trend with increase in w/c ratios for a given type of cement. Performance of fly ash based Portland pozzolana cement was superior to other types of cements for a w/c of 0.55. The fundamental degradation mechanisms of limestone mortars during hot liquid sodium interactions include alterations in cement paste phase, formation of sodium compounds from the interaction between solid phases of cement paste and aggregate, modifications of interfacial transition zone (ITZ), decomposition of CaCO 3 , widening and etching of rhombohedral cleavages, and subsequent breaking through the weakest rhombohedral cleavage planes of calcite, staining, ferric oxidation in grain boundaries and disintegration of impurity minerals in limestone

  14. Resedimented Limestones in Middle and Upper Jurassic Succession of the Slovenian Basin

    Directory of Open Access Journals (Sweden)

    Boštjan Rožič

    2006-12-01

    Full Text Available The Middle and Upper Jurassic succession of the Slovenian Basin is characterized by pelagic sedimentation of siliceous limestones and radiolarian cherts. In the southern and central part of the basin two packages of resedimented limestones are interbedded within pelagic sediments. The Lower resedimented limestones are lower-middle Bajocian to lower Callovian in age. In the southern part of the basin they form laterally discontinuous sequences composed of limestone breccias, calcarenites and micritic limestone and in the central part of the basin calcarenite intercalations within pelagic beds. They were transported by turbidity currents from highly productive ooidal shoals of the Dinaric Carbonate Platform. The Lower resedimented carbonates correlate with the lower three members of the Travnik Formation in the Bovec Trough and similarly developed but much thicker Vajont Formation in the Belluno Basin. The difference in thickness is interpreted as a consequence of shallow-water and longshore currents on the Dinaric Carbonate Platform that transported platform material towards southwest in the direction of the Belluno Basin. The Upper resedimented limestones are upper Kimmeridgian to lower Tithonian and occur within radiolarian cherts in the upper part of the succession as calcarenite beds that originated by turbidity currents. Onset of resedimentation coincides with the emersion-related demise of barrier reef and following deposition of micritic and rare oolitic limestones on the Dinaric Carbonate Platform. Approximatelly coeval resedimented limestones occur in the fourth member of the Travnik Formation in the Bovec Trough, but are not reported from the Ammonitico Rosso Superiore Formation in the Belluno Basin.

  15. Volume change of limestone and its effects on drying shrinkage of concrete

    OpenAIRE

    YAGI, Shogo; AQUINO, Carlos; INOUE, Masumi; OKAMOTO, Takahisa

    2010-01-01

    Recently, the cracks of concrete by drying shrinkage become one of the problems in the construction industry in Japan. The drying shrinkage decreases when the concrete is produced with limestone aggregate. However, it is not clear why the drying shrinkage is decreased. The purpose of this study is to clarify the relation between the drying shrinkage of concrete and the limestone aggregate. In this study, the experiments about the strength, elasticity and drying shrinkage of concrete and the p...

  16. CARBONIFEROUS CORALS AND CHAETETIDS FROM EXOTIC LIMESTONE BLOCK OF THE CRIMEA

    OpenAIRE

    OGAR, VICTOR; KLEVTSOVSKYI, ANDREY

    2015-01-01

    A chaetetid sponge and coral fauna from a Carboniferous exotic limestone block in the Lower Jurassic Esciorda olistostrome on the Bodrak River (Crimean Mountains) are described for the first time. The Bodrak exotic block is composed of massive limestone. It contains the chaetetid Chaetetes (Boswellia) sp., the tabulate coral Multithecopora sp., and poorly preserved rugose corals, including Dibunophyllum? sp., Cordibia? sp. and gen. et sp. indet. Only the fasciculate colonies of the rugose cor...

  17. A Coordinated USGS Science Response to Hurricane Sandy

    Science.gov (United States)

    Jones, S.; Buxton, H. T.; Andersen, M.; Dean, T.; Focazio, M. J.; Haines, J.; Hainly, R. A.

    2013-12-01

    In late October 2012, Hurricane Sandy came ashore during a spring high tide on the New Jersey coastline, delivering hurricane-force winds, storm tides exceeding 19 feet, driving rain, and plummeting temperatures. Hurricane Sandy resulted in 72 direct fatalities in the mid-Atlantic and northeastern United States, and widespread and substantial physical, environmental, ecological, social, and economic impacts estimated at near $50 billion. Before the landfall of Hurricane Sandy, the USGS provided forecasts of potential coastal change; collected oblique aerial photography of pre-storm coastal morphology; deployed storm-surge sensors, rapid-deployment streamgages, wave sensors, and barometric pressure sensors; conducted Light Detection and Ranging (lidar) aerial topographic surveys of coastal areas; and issued a landslide alert for landslide prone areas. During the storm, Tidal Telemetry Networks provided real-time water-level information along the coast. Long-term networks and rapid-deployment real-time streamgages and water-quality monitors tracked river levels and changes in water quality. Immediately after the storm, the USGS serviced real-time instrumentation, retrieved data from over 140 storm-surge sensors, and collected other essential environmental data, including more than 830 high-water marks mapping the extent and elevation of the storm surge. Post-storm lidar surveys documented storm impacts to coastal barriers informing response and recovery and providing a new baseline to assess vulnerability of the reconfigured coast. The USGS Hazard Data Distribution System served storm-related information from many agencies on the Internet on a daily basis. Immediately following Hurricane Sandy the USGS developed a science plan, 'Meeting the Science Needs of the Nation in the Wake of Hurricane Sandy-A U.S. Geological Survey Science Plan for Support of Restoration and Recovery'. The plan will ensure continuing coordination of internal USGS activities as well as

  18. ACHIEVEMENTS AND PERSPECTIVES ON STONE FRUIT GROWING ON SANDY SOILS

    Directory of Open Access Journals (Sweden)

    Anica Durău

    2012-01-01

    Full Text Available Climatic conditions in the sandy soils of southern Oltenia encourage cultivation of tree species in terms of applying specific technologies. Possibility of poor sandy soils fertile capitalization, earliness in 7- 10 days of fruit ripening , high yields and quality are the main factors supporting the development of fruit growing in the sandy soils of southern Oltenia. The main objectives of the research were to CCDCPN Dăbuleni. Establish and improve stone fruit species assortment, adapted to the stress of the sandy soils, establishment and evaluation of the influence of stress on trees and their influence on the size and quality of production, development of technological links (planting distances, forms management, fertilization, getting high and consistent annual production of high quality, containing low as pesticide residues, to establish a integrated health control program of the trees with emphasis on biotechnical. Research has shown good stone species behavior, and their recommended proportion is 75% of all fruit trees (peach 36%, 14% apricot, plum15%, sweet and sour cherry fruit growing 10% of the total area. Results on peach varieties revealed: ’Redhaven’, ’Suncrest’, ’Loring’ with yields ranging from (24.8 t / ha to 29.0 t/ha with maturation period from July to August, and varieties ’NJ 244’, ’Fayette’, ’Flacara’ with productions ranging from (19.7 t / ha to 23.0 t/ha with maturation period from August to September. The sweet cherry varieties ’Van’, ’Rainier’, ’Stella’, with yields ranging from 17. 2 to 24.4 t / ha. In the range studied sour cherry were found ’Oblacinska’ varieties of 11.0 t / ha, ’Cernokaia’ with 10.5 t / ha, ’Schatten Morelle’ with 9.1 t / ha. Optimum planting density and shape of the peach crown found that the highest yields of fruit are produced in the form of vertical cordon crown, with values ranging from 15.9 t / ha at a distance of 2 m, 10.3 t / ha at a distance

  19. Enhancement of direct sulfation of limestone by Na{sub 2}CO{sub 3} addition

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Chuanmin [School of Environmental Science and Engineering, North China Electric Power University, Baoding 071003, Hebei Province (China); Zhuang, Ye [Energy and Environmental Research Center, University of North Dakota, 15 North 23rd Street, Grand Forks, ND 58203 (United States); Wang, Chunbo [Department of Power engineering, North China Electric Power University, Baoding 071003, Hebei Province (China)

    2009-07-15

    For an oxy-fuel circulating fluidized bed combustion system, the limestone calcination is normally prevented due to excessive CO{sub 2} partial pressures and the limestone is subject to a direct sulfation reaction. The enhancement of the direct sulfation of limestone by Na{sub 2}CO{sub 3} was investigated under high CO{sub 2} partial pressure in a thermogravimetric apparatus (TGA) and scanning electron microscope (SEM) analysis method. A commercial limestone with a mean size of 18.8 {mu}m was used. Experimental results indicate that the incorporation of Na{sup +} ions in solid product CaSO{sub 4} lattice structures results in formation of more extrinsic point defects in the crystal lattices of CaSO{sub 4} and a significantly increased solid-state diffusivity/mobility in the solid product. So the direct sulfation of Na{sub 2}CO{sub 3}-doped limestone shows higher rate and higher degree of conversion in the later stage of sulfation, in comparison with the direct sulfation of original limestone. The reaction changes from diffusional control to chemical reaction control in the presence of Na{sub 2}CO{sub 3} because of the effect of foreign ions on accelerating the solid-state diffusion. (author)

  20. Enhancement of direct sulfation of limestone by Na{sub 2}CO{sub 3} addition

    Energy Technology Data Exchange (ETDEWEB)

    Chuanmin Chen; Ye Zhuang; Chunbo Wang [North China Electric Power University, Baoding (China). School of Environmental Science & Engineering

    2009-07-15

    For an oxy-fuel circulating fluidized bed combustion system, the limestone calcination is normally prevented due to excessive CO{sub 2} partial pressures and the limestone is subject to a direct sulfation reaction. The enhancement of the direct sulfation of limestone by Na{sub 2}CO{sub 3} was investigated under high CO{sub 2} partial pressure in a thermogravimetric apparatus (TGA) and scanning electron microscope (SEM) analysis method. A commercial limestone with a mean size of 18.8 {mu}m was used. Experimental results indicate that the incorporation of Na{sup +} ions in solid product CaSO{sub 4} lattice structures results in formation of more extrinsic point defects in the crystal lattices of CaSO{sub 4} and a significantly increased solid-state diffusivity/mobility in the solid product. So the direct sulfation of Na{sub 2}CO{sub 3}-doped limestone shows higher rate and higher degree of conversion in the later stage of sulfation, in comparison with the direct sulfation of original limestone. The reaction changes from diffusional control to chemical reaction control in the presence of Na{sub 2}CO{sub 3} because of the effect of foreign ions on accelerating the solid-state diffusion. 33 refs., 7 figs., 2 tabs.

  1. Direct sulfation of limestone based on oxy-fuel combustion technology

    Energy Technology Data Exchange (ETDEWEB)

    Chen, C.M.; Zhao, C.S.; Liu, S.T.; Wang, C.B. [North China Electric Power University, Baoding (China)

    2009-10-15

    With limestone as the sorbent, the sulfation reaction can proceed via two different routes depending on whether calcination of the limestone takes place under the given reaction conditions. The direct sulfation reaction is defined as the sulfation reaction between sulfur dioxide (SO{sub 2}) and limestone in an uncalcined state. This reaction, based on oxyfuel combustion technology, was studied by thermogravimetric analysis. Surface morphologies of the limestone particles after sulfation were examined by a scanning electron microscope. Results show that there are more pores or gaps in the product layer formed by direct sulfation of limestone than by indirect sulfation, which can be attributed to the generation of carbon dioxide (CO{sub 2}) at a reaction interface. Compared with indirect sulfation, direct sulfation of limestone can yield much higher conversion and has a much higher reaction rate. For direct sulfation, the greater porosity in the product layer greatly reduces the solid-state ion diffusion distance, resulting in a higher reaction rate and higher conversion.

  2. Interpretation of well hydrographs in the karstic Maynardville Limestone at the Oak Ridge Y-12 Plant

    International Nuclear Information System (INIS)

    Shevenell, L.A.; McMaster, B.W.

    1996-06-01

    The Maynardville Limestone in Oak Ridge, Tennessee underlies the southern portion of Bear Creek Valley (BCV), and is considered to be the primary pathway for groundwater leaving the Y-12 Plant boundaries. Sixty-seven percent of all wells drilled into the Maynardville Limestone have intersected at least one cavity, suggesting karst features may be encountered throughout the shallow (< 200 ft) portions of the Limestone. Because waste facilities at the Y-12 Plant are located adjacent to the Maynardville Limestone, contaminants could enter the karst aquifer and be transported in the conduit system. As part of an overall hydrologic characterization effort of this karst aquifer, 41 wells in the Maynardville Limestone were instrumented with pressure transducers to monitor water level changes (hydrographs) associated with rain events. Wells at depths between approximately 20 and 750 ft were monitored over the course of at least two storms in order that variations with depth could be identified. The wells selected were not exclusively completed in cavities but were selected to include the broad range of hydrologic conditions present in the Maynardville Limestone. Cavities, fractures and diffuse flow zones were measured at a variety of depths. The water level data from the storms are used to identify areas of quickflow versus slower flowing water zones. The data are also used to estimate specific yields and continuum transmissitives in different portions of the aquifer

  3. Studies on limestone concrete as a low-activation structural material for nuclear power plants

    International Nuclear Information System (INIS)

    Uematsu, Mikio; Nagano, Hiroshi; Naito, Yasuhiro

    2000-01-01

    Because of low content of Li, Co and Eu, the target nuclides of activation reaction, limestone concrete is considered to be effective in reducing the decommissioning cost of nuclear plants. Induced activity calculation and structural strength test were performed for limestone concrete and the results were compared with the data obtained for sandstone concrete, which is generally used in nuclear plants. Minor elements, which are important from the viewpoint of activation, were measured with elementary analysis for limestone samples from three different quarries in Japan. Induced activity in biological shield walls (BSW) of Boiling Water Reactor (BWR) plants was calculated with the isotope generation code ORIGEN-79 using neutron flux data obtained with the one-dimensional Sn transport code ANISN and MGCL 137-group activation cross section library based on JENDL-3. Estimated total radioactivity accumulated in limestone concrete BSW was 5 times lower than that in the sandstone concrete BSW. Structural strength were compared between limestone concrete and sandstone concrete, and limestone concrete was found to have enough compressive strength and tensile strength. (author)

  4. Accelerated weathering of limestone for CO2 mitigation opportunities for the stone and cement industries

    Science.gov (United States)

    Langer, W.H.; Juan, C.A.S.; Rau, G.H.; Caldeira, K.

    2009-01-01

    Large amounts of limestone fines coproduced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO 2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point-sources such as cement manufacturing. AWL reactants are readily available, inexpensive, and environmentally benign. Waste CO 2 is hydrated with water to produce carbonic acid, which then reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities within about 10 km of the coastline. The majority of U.S. coastal power generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufactures, and research scientists.

  5. Influence of limestone waste as partial replacement material for sand and marble powder in concrete properties

    Directory of Open Access Journals (Sweden)

    Omar M. Omar

    2012-12-01

    Full Text Available Green concrete are generally composed of recycling materials as hundred or partial percent substitutes for aggregate, cement, and admixture in concrete. Limestone waste is obtained as a by-product during the production of aggregates through the crushing process of rocks in rubble crusher units. Using quarry waste as a substitute of sand in construction materials would resolve the environmental problems caused by the large-scale depletion of the natural sources of river and mining sands. This paper reports the experimental study undertaken to investigate the influence of partial replacement of sand with limestone waste (LSW, with marble powder (M.P as an additive on the concrete properties. The replacement proportion of sand with limestone waste, 25%, 50%, and 75% were practiced in the concrete mixes except in the concrete mix. Besides, proportions of 5%, 10% and 15% marble powder were practiced in the concrete mixes. The effects of limestone waste as fine aggregate on several fresh and hardened properties of the concretes were investigated. The investigation included testing of compressive strength, indirect tensile strength, flexural strength, modulus of elasticity, and permeability. It was found that limestone waste as fine aggregate enhanced the slump test of the fresh concretes. But the unit weight concretes were not affected. However, the good performance was observed when limestone waste as fine aggregate was used in presence of marble powder.

  6. Environmentally acceptable effect of hydrogen peroxide on cave 'lamp-flora', calcite speleothems and limestones

    International Nuclear Information System (INIS)

    Faimon, Jiri; Stelcl, Jindrich; Kubesova, Svatava; Zimak, Jiri

    2003-01-01

    Hydrogen peroxide plus limestone fragments allows removal of organisms without corrosion of limestone and speleothem. - Mosses, algae, and cyanobacteria (lamp-flora) colonize illuminated areas in show caves. This biota is commonly removed by a sodium hypochlorite solution. Because chlorine and other deleterious compounds are released into a cave environment during lamp-flora cleansing, hydrogen peroxide was tested as an alternative agent. In a multidisciplinary study conducted in the Katerinska Cave (Moravian Karst, Czech Republic), 12 algae- and cyanobacteria taxons and 19 moss taxons were detected. The threshold hydrogen peroxide concentration for the destruction of this lamp-flora was found to be 15 vol.%. Based on laboratory experiments in stirred batch reactors, the dissolution rates of limestones and calcite speleothems in water were determined as 3.77x10 -3 and 1.81x10 -3 mol m -2 h -1 , respectively. In the 15% peroxide solution, the limestone and speleothem dissolution rates were one order of magnitude higher, 2.00x10 -2 and 2.21x10 -2 mol m -2 h -1 , respectively. So, the peroxide solution was recognised to attack carbonates somewhat more aggressively than karst water. In order to prevent the potential corrosion of limestone and speleothems, the reaching of preliminary peroxide saturation with respect to calcite is recommended, for example, by adding of few limestone fragments into the solution at least 10 h prior to its application

  7. The fate of fresh and stored 15N-labelled sheep urine and urea applied to a sandy and a sandy loam soil using different application strategies

    DEFF Research Database (Denmark)

    Sørensen, P.; Jensen, E.S.

    1996-01-01

    The fate of nitrogen from N-15-labelled sheep urine and urea applied to two soils was studied under field conditions. Labelled and stored urine equivalent to 204 kg N ha(-1) was either incorporated in soil or applied to the soil surface prior to sowing of Italian ryegrass (Lolium multiflorum L...... and soil was not significantly different for incorporated urine and urea. Almost all the supplied labelled N was accounted for in soil and herbage in the sandy loam soil, whereas 33-34% of the labelled N was unaccounted for in the sandy soil. When the stored urine was applied to the soil surface, 20...... was applied to growing ryegrass at the sandy loam soil, the immobilization of urine-derived N was significantly reduced compared to application prior to sowing. The results indicated that the net mineralization of urine N was similar to that of urea in the sandy soil, but only about 75% of the urine N was net...

  8. Abrasive wear based predictive maintenance for systems operating in sandy conditions

    NARCIS (Netherlands)

    Woldman, M.; Tinga, T.; Heide, E. van der; Masen, M.A.

    2015-01-01

    Machines operating in sandy environments are damaged by the abrasive action of sand particles that enter the machine and become entrapped between components and contacting surfaces. In the case of the military services the combination of a sandy environment and the wide range of tasks to be

  9. Measuring Sandy Bottom Dynamics by Exploiting Depth from Stereo Video Sequences

    DEFF Research Database (Denmark)

    Musumeci, Rosaria E.; Farinella, Giovanni M.; Foti, Enrico

    2013-01-01

    In this paper an imaging system for measuring sandy bottom dynamics is proposed. The system exploits stereo sequences and projected laser beams to build the 3D shape of the sandy bottom during time. The reconstruction is used by experts of the field to perform accurate measurements and analysis...

  10. 33 CFR 80.170 - Sandy Hook, NJ to Tom's River, NJ.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Sandy Hook, NJ to Tom's River, NJ. 80.170 Section 80.170 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INTERNATIONAL NAVIGATION RULES COLREGS DEMARCATION LINES Atlantic Coast § 80.170 Sandy Hook, NJ to Tom's River...

  11. 77 FR 74891 - Order Granting Exemptions From Certain Rules of Regulation SHO Related to Hurricane Sandy

    Science.gov (United States)

    2012-12-18

    ... Client Update on Superstorm Sandy--Current and Ongoing Operations as Markets Re-Open; Physical.../downloads/legal/imp_notices/2012/dtcc/z0033.pdf ; ``DTCC Client Update on Superstorm Sandy--Physical...://www.dtcc.com/downloads/legal/imp_notices/2012/dtcc/z0035.pdf ; ``DTCC Client Update on Superstorm...

  12. Fine-scale spatial distribution of plants and resources on a sandy soil in the Sahel

    NARCIS (Netherlands)

    Rietkerk, M.G.; Ouedraogo, T.; Kumar, L.; Sanou, S.; Langevelde, F. van; Kiema, A.; Koppel, J. van de; Andel, J. van; Hearne, J.; Skidmore, A.K.; Ridder, N. de; Stroosnijder, L.; Prins, H.H.T.

    2002-01-01

    We studied fine-scale spatial plant distribution in relation to the spatial distribution of erodible soil particles, organic matter, nutrients and soil water on a sandy to sandy loam soil in the Sahel. We hypothesized that the distribution of annual plants would be highly spatially autocorrelated

  13. Experimental study and mechanism analysis of modified limestone by red mud for improving desulfurization

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Hongtao; Han, Kuihua; Niu, Shengli; Lu, Chunmei; Liu, Mengqi; Li, Hui [Shandong Univ., Jinan (China). School of Energy and Power Engineering

    2013-07-01

    Red mud is a type of solid waste generated during alumina production from bauxite, and how to dispose and utilize red mud in a large scale is yet a question with no satisfied answer. This paper attempts to use red mud as a kind of additive to modify the limestone. The enhancement of the sulfation reaction of limestone by red mud (two kinds of Bayer process red mud and one kind of sintering process red mud) are studied by a tube furnace reactor. The calcination and sulfation process and kinetics are investigated in a thermogravimetric (TG) analyzer. The results show that red mud can effectively improve the desulfurization performance of limestone in the whole temperature range (1,073-1,373K). Sulfur capacity of limestone (means quality of SO{sub 2} which can be retained by 100mg of limestone) can be increased by 25.73, 7.17 and 15.31% while the utilization of calcium can be increased from 39.68 to 64.13%, 60.61 and 61.16% after modified by three kinds of red mud under calcium/metallic element (metallic element described here means all metallic elements which can play a catalytic effect on the sulfation process, including the Na, K, Fe, Ti) ratio being 15, at the temperature of 1,173K. The structure of limestone modified by red mud is interlaced and tridimensional which is conducive to the sulfation reaction. The phase composition analysis measured by XRD of modified limestone sulfated at high temperature shows that there are correspondingly more sulphates for silicate and aluminate complexes of calcium existing in the products. Temperature, calcium/metallic element ratio and particle diameter are important factors as for the sulfation reaction. The optimum results can be obtained as calcium/metallic element ratio being 15. Calcination characteristic of limestone modified by red mud shows a migration to lower temperature direction. The enhancement of sulfation by doping red mud is more pronounced once the product layer has been formed and consequently the promoting

  14. Nomination of the Globigerina Limestone of the Maltese Islands as a "Global Heritage Stone Resource"

    Science.gov (United States)

    Cassar, JoAnn

    2016-04-01

    The Maltese Islands consist of two main islands, Malta and Gozo, as well as a small number of islets, and lie in the central Mediterranean Sea approximately 90 km south of Sicily. Although only 316 square kilometres in size, the Islands contain a rich concentration of archaeological sites and historic buildings, as well as vernacular architecture and modern buildings, for the most part built of the local Globigerina Limestone, which is one of the few natural resources of the Islands. This stone can be described as a typical "soft limestone", very easy to carve and shape. It forms part of the large family of Oligo-Miocene "soft limestones" widely diffused in the Mediterranean Basin. The Maltese Globigerina Limestone Formation is one of five main Formations, and varies in thickness from 20 to over 200 m. The material used for building is located stratigraphically in the lower part of the Globigerina Limestone Formation, called the Lower Globigerina Limestone. This Formation is stratified into thick beds at outcrop. Sections where bioturbation is concentrated often also occur. This limestone is fine-grained, yellow to pale grey in colour, almost wholly composed of the tests of globigerinid planktonic foraminifera. Petrographically, Globigerina Limestone can be described as a bioclastic packstone, with bioclastic wackestones also occurring. This limestone has always been used as the predominant building material in the Islands. The Maltese prehistoric Temples, which were constructed approximately 6000 years ago, bear testimony to this. Between 1530 and 1798 the Order of the Knights of St John built kilometres of fortifications in this same material to protect the Island from the expanding Ottoman Empire. Fortifications, impressive churches, auberges and palaces were built of this stone during this period. The capital city of Valletta, a rich and dense manifestation of Baroque architecture in Globigerina Limestone, is included on the UNESCO World Heritage List, as are

  15. Swashed away? Storm impacts on sandy beach macrofaunal communities

    Science.gov (United States)

    Harris, Linda; Nel, Ronel; Smale, Malcolm; Schoeman, David

    2011-09-01

    Storms can have a large impact on sandy shores, with powerful waves eroding large volumes of sand off the beach. Resulting damage to the physical environment has been well-studied but the ecological implications of these natural phenomena are less known. Since climate change predictions suggest an increase in storminess in the near future, understanding these ecological implications is vital if sandy shores are to be proactively managed for resilience. Here, we report on an opportunistic experiment that tests the a priori expectation that storms impact beach macrofaunal communities by modifying natural patterns of beach morphodynamics. Two sites at Sardinia Bay, South Africa, were sampled for macrofauna and physical descriptors following standard sampling methods. This sampling took place five times at three- to four-month intervals between April 2008 and August 2009. The second and last sampling events were undertaken after unusually large storms, the first of which was sufficiently large to transform one site from a sandy beach into a mixed shore for the first time in living memory. A range of univariate (linear mixed-effects models) and multivariate (e.g. non-metric multidimensional scaling, PERMANOVA) methods were employed to describe trends in the time series, and to explore the likelihood of possible explanatory mechanisms. Macrofaunal communities at the dune-backed beach (Site 2) withstood the effects of the first storm but were altered significantly by the second storm. In contrast, macrofauna communities at Site 1, where the supralittoral had been anthropogenically modified so that exchange of sediments with the beach was limited, were strongly affected by the first storm and showed little recovery over the study period. In line with predictions from ecological theory, beach morphodynamics was found to be a strong driver of temporal patterns in the macrofaunal community structure, with the storm events also identified as a significant factor, likely

  16. Water Infiltration and Hydraulic Conductivity in Sandy Cambisols

    DEFF Research Database (Denmark)

    Bens, Oliver; Wahl, Niels Arne; Fischer, Holger

    2006-01-01

    from pure Scots pine stands towards pure European beech stands. The water infiltration capacity and hydraulic conductivity (K) of the investigated sandy-textured soils are low and very few macropores exist. Additionally these pores are marked by poor connectivity and therefore do not have any...... of the experimental soils. The results indicate clearly that soils play a crucial role for water retention and therefore, in overland flow prevention. There is a need to have more awareness on the intimate link between the land use and soil properties and their possible effects on flooding.......Soil hydrological properties like infiltration capacity and hydraulic conductivity have important consequences for hydrological properties of soils in river catchments and for flood risk prevention. They are dynamic properties due to varying land use management practices. The objective...

  17. Performance of social network sensors during Hurricane Sandy.

    Directory of Open Access Journals (Sweden)

    Yury Kryvasheyeu

    Full Text Available Information flow during catastrophic events is a critical aspect of disaster management. Modern communication platforms, in particular online social networks, provide an opportunity to study such flow and derive early-warning sensors, thus improving emergency preparedness and response. Performance of the social networks sensor method, based on topological and behavioral properties derived from the "friendship paradox", is studied here for over 50 million Twitter messages posted before, during, and after Hurricane Sandy. We find that differences in users' network centrality effectively translate into moderate awareness advantage (up to 26 hours; and that geo-location of users within or outside of the hurricane-affected area plays a significant role in determining the scale of such an advantage. Emotional response appears to be universal regardless of the position in the network topology, and displays characteristic, easily detectable patterns, opening a possibility to implement a simple "sentiment sensing" technique that can detect and locate disasters.

  18. Hurricane Sandy: Shared Trauma and Therapist Self-Disclosure.

    Science.gov (United States)

    Rao, Nyapati; Mehra, Ashwin

    2015-01-01

    Hurricane Sandy was one of the most devastating storms to hit the United States in history. The impact of the hurricane included power outages, flooding in the New York City subway system and East River tunnels, disrupted communications, acute shortages of gasoline and food, and a death toll of 113 people. In addition, thousands of residences and businesses in New Jersey and New York were destroyed. This article chronicles the first author's personal and professional experiences as a survivor of the hurricane, more specifically in the dual roles of provider and trauma victim, involving informed self-disclosure with a patient who was also a victim of the hurricane. The general analytic framework of therapy is evaluated in the context of the shared trauma faced by patient and provider alike in the face of the hurricane, leading to important implications for future work on resilience and recovery for both the therapist and patient.

  19. Performance of Social Network Sensors during Hurricane Sandy

    Science.gov (United States)

    Kryvasheyeu, Yury; Chen, Haohui; Moro, Esteban; Van Hentenryck, Pascal; Cebrian, Manuel

    2015-01-01

    Information flow during catastrophic events is a critical aspect of disaster management. Modern communication platforms, in particular online social networks, provide an opportunity to study such flow and derive early-warning sensors, thus improving emergency preparedness and response. Performance of the social networks sensor method, based on topological and behavioral properties derived from the “friendship paradox”, is studied here for over 50 million Twitter messages posted before, during, and after Hurricane Sandy. We find that differences in users’ network centrality effectively translate into moderate awareness advantage (up to 26 hours); and that geo-location of users within or outside of the hurricane-affected area plays a significant role in determining the scale of such an advantage. Emotional response appears to be universal regardless of the position in the network topology, and displays characteristic, easily detectable patterns, opening a possibility to implement a simple “sentiment sensing” technique that can detect and locate disasters. PMID:25692690

  20. Studies on the preparation of value-added products for limestone

    Energy Technology Data Exchange (ETDEWEB)

    Chae, Young Bae; Jeong, Soo Bok; Ko, Won Sik; Park, Je Shin; Oh, Jung Whan [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

    1997-12-01

    Most of limestone in our country was consumed by the cement and iron/steel making industries and the amount of that was up to 72 million ton in 1996. Recently, importation of high grade limestone that have properties of high whiteness and grade are increased with diversification of chemical products and powder as various qualified filler, because high grade limestone are limited and of few deposit in our country. Therefore, the purpose of this study has investigated to raise to high grade by economical processes with low grade of domestic limestone. In this year, first of all, we investigated the status of application utilize and related industries with the domestic limestone, and then being consideration with condition selected the adequate sample from Andong, Jungsun and Kumsan area. Magnetic materials were involved in impurities of sample, so magnetic separation method was applied in elimination of the ferro-magnetic materials and para-magnetic materials, such as chlorite, muscovite, quartz, dolomite, magnetite, feldspar and so on. The limestone sample has many kinds of impurity. Investigation of flotation was undertaken to eliminate impurities from limestone crude ore and the tests were performed to get a optimum condition adding oleic acid as a promoter, sodium silicate and sodium carbonate as a conditioning agents and MIBC as a frother, while to float the sulfide minerals added amyl xanthate as a promoter, and sulfuric acid as a pH regulator. And most of the impurities involving in flotation sink contained such as quartz, chlorite, muscovite, feldspar, dolomite and so on. Selective crushing and classification methods were performed to eliminate impurities depends on the mineral properties and should be the selective crushing methods are very useful at the manufacturing factory of heavy calcium carbonate with the dry milling system. (author). 36 refs., 46 tabs., 33 figs.

  1. Phosphorus distribution in sandy soil profile under drip irrigation system

    International Nuclear Information System (INIS)

    El-Gendy, R.W.; Rizk, M.A.; Abd El Moniem, M.; Abdel-Aziz, H.A.; Fahmi, A.E.

    2009-01-01

    This work aims at to studying the impact of irrigation water applied using drip irrigation system in sandy soil with snap bean on phosphorus distribution. This experiment was carried out in soils and water research department farm, nuclear research center, atomic energy authority, cairo, Egypt. Snap bean was cultivated in sandy soil and irrigated with 50,37.5 and 25 cm water in three water treatments represented 100, 75 and 50% ETc. Phosphorus distribution and direction of soil water movement had been detected in three sites on the dripper line (S1,S2 and S3 at 0,12.5 and 25 cm distance from dripper). Phosphorus fertilizer (super phosphate, 15.5% P 2 O 5 in rate 300 kg/fed)was added before cultivation. Neutron probe was used to detect the water distribution and movement at the three site along soil profile. Soil samples were collected before p-addition, at end developing, mid, and late growth stages to determine residual available phosphorus. The obtained data showed that using 50 cm water for irrigation caused an increase in P-concentration till 75 cm depth in the three sites of 100% etc treatment, and covered P-requirements of snap bean for all growth stages. As for 37.5 and 25 cm irrigation water cannot cover all growth stages for P-requirements of snap bean. It could be concluded that applied irrigation water could drive the residual P-levels till 75 cm depth in the three sites. Yield of the crop had been taken as an indicator as an indicator profile. Yield showed good response according to water quantities and P-transportation within the soil profile

  2. Quantifying human mobility perturbation and resilience in Hurricane Sandy.

    Directory of Open Access Journals (Sweden)

    Qi Wang

    Full Text Available Human mobility is influenced by environmental change and natural disasters. Researchers have used trip distance distribution, radius of gyration of movements, and individuals' visited locations to understand and capture human mobility patterns and trajectories. However, our knowledge of human movements during natural disasters is limited owing to both a lack of empirical data and the low precision of available data. Here, we studied human mobility using high-resolution movement data from individuals in New York City during and for several days after Hurricane Sandy in 2012. We found the human movements followed truncated power-law distributions during and after Hurricane Sandy, although the β value was noticeably larger during the first 24 hours after the storm struck. Also, we examined two parameters: the center of mass and the radius of gyration of each individual's movements. We found that their values during perturbation states and steady states are highly correlated, suggesting human mobility data obtained in steady states can possibly predict the perturbation state. Our results demonstrate that human movement trajectories experienced significant perturbations during hurricanes, but also exhibited high resilience. We expect the study will stimulate future research on the perturbation and inherent resilience of human mobility under the influence of hurricanes. For example, mobility patterns in coastal urban areas could be examined as hurricanes approach, gain or dissipate in strength, and as the path of the storm changes. Understanding nuances of human mobility under the influence of such disasters will enable more effective evacuation, emergency response planning and development of strategies and policies to reduce fatality, injury, and economic loss.

  3. 78 FR 7780 - Sunshine Act Meeting; FCC Announces Further Details for the First Post-Superstorm Sandy Field...

    Science.gov (United States)

    2013-02-04

    ... First Post-Superstorm Sandy Field Hearing, Tuesday, February 5, 2013 AGENCY: Federal Communications Commission. ACTION: Sunshine notice. SUMMARY: In the wake of Superstorm Sandy, Federal Communications... focusing on the impact of Superstorm Sandy, and help inform recommendations and actions to strengthen wired...

  4. Ecological Study in Two Quarried Limestone Karst Hills in Bogor West Java: Vegetation Structure and Floristic Composition

    OpenAIRE

    SATYANTI, ANNISA; CANDRA KUSUMA, YAYAN WAHYU

    2010-01-01

    Many species extinctions have probably gone unnoticed on limestone that was destroyed before they could be sampled. Unless biodiversity surveys are intensified, the true magnitude of extinctions will never be ascertained. The objectives of this study were to determine tree species composition of limestone hills in Nyungcung and Ciampea; to determine quantitatively the dominant and less dominant species and to quantify floristic structure of the two limestone hills. Value of richness (Menhinic...

  5. Effective stress law for the permeability and deformation of four porous limestones

    Science.gov (United States)

    Wang, Y.; Meng, F.; Wang, X.; Baud, P.; Wong, T. F.

    2017-12-01

    The effective stress behavior of a rock is related to the geometric of its pore space. In a microscopically homogeneous assemblage, effective stress coefficients for permeability, volumetric strain and porosity change are predicted to be equal to or less than unity. Experimental measurements are in basic agreement with this prediction, with exceptions particularly in clay-rich sandstones, for which effective stress coefficient for permeability up to 7 was documented. Little is known about carbonates, but Ghabezloo et al. [2009] studied the permeability of an oolitic limestone (from Nimes, France) with 17% porosity and reported effective stress coefficients up to 2.4. We investigated this phenomenon in Indiana, Leitha, Purbeck, and Thala limestones with porosities of 13-30%. Measurements were made at room temperature on water-saturated samples at confining and pore pressures of 7-15 MPa and 1-3 MPa, respectively. Unlike previous studies limited to the permeability, we also determined the effective stress coefficients for volumetric strain and porosity change. Indiana limestone is oolitic, and not surprisingly its behaviour was similar to Nimes limestone, with an effective stress coefficient for permeability of 2.5. Our Indiana limestone data showed that whereas the effective stress coefficient for volumetric strain was 1. Measurements on Purbeck and Thala limestones are consistent with these inequalities, with effective stress coefficients for permeability and porosity change >1 and that for volumetric strain <1. Even though Purbeck and Thala limestones are micritic with appreciable amount of quartz and dolomite, microstructural and mercury porosimetry data showed that their pore spaces are similar to the oolitic limestones, in that the pore size distribution is bimodal with significant fractions of both macropores and micropores. Berryman [1992] analyzed theoretically a rock made up of two porous constituents. Our new data are in agreement with inequalities he

  6. Drenov Grič black limestone as a heritage stone from Slovenia

    Science.gov (United States)

    Kramar, Sabina; Rožič, Boštjan; Žbona, Nina; Bedjanič, Mojca; Mladenović, Ana

    2016-04-01

    The limestone known as Drenov Grič black limestone is considered one of the most beautiful Slovenian natural stones due to its homogenous black colour interwoven with white veins. Over the centuries it has been exploited from three major quarries west of Ljubljana, with the main quarry at Drenov Grič playing the primary role in supplying building material for the central parts of Slovenia. All the quarries are currently not active. In the area of Drenov grič, one locality of black limestone is protected - Kuclerjev kamnolom quarry. It has the status of 'valuable natural feature of national importance' and is protected as a natural monument. This well-stratified micritic limestone of Triassic (Carnian) age occurs in 10-80 cm thick beds, with thin marl interlayers. The stone contains abundant fossil bivalves and ostracods. Apart from calcite as the main component, dolomite, quartz, illite/muscovite and pyrite are also present. The limestone is relatively rich in carbonaceous and bituminous organic matter, which is responsible for the black colour of the stone. This component does not have any adverse effect on mechanical and physical characteristics. As the lime¬stone is dense, thus facilitating a good polish, it has been commercially considered as marble. The stone has been widely used in Slovenian monuments, not only in Ljubljana but also in other regions of Slovenia. Many inner and outdoor architectural elements were made of this limestone, particularly in the baroque period, which was known for the extensive use of black limestones also in other European countries. The most significant use of this limestone has been recorded in sculptured portals and altars. Some of the important buildings decorated utilising this stone, are the Ljubljana Cathedral, the St. James's Parish Church, and the Franciscan Church of the Annunciation, all of which are located in Ljubljana, some of them having been declared as cultural monuments of local or national importance. When

  7. Steam Cured Self-Consolidating Concrete and the Effects of Limestone Filler

    Science.gov (United States)

    Aqel, Mohammad A.

    The purpose of this thesis is to determine the effect and the mechanisms associated with replacing 15% of the cement by limestone filler on the mechanical properties and durability performance of self-consolidating concrete designed and cured for precast/prestressed applications. This study investigates the role of limestone filler on the hydration kinetics, mechanical properties (12 hours to 300 days), microstructural and durability performance (rapid chloride permeability, linear shrinkage, sulfate resistance, freeze-thaw resistance and salt scaling resistance) of various self-consolidating concrete mix designs containing 5% silica fume and steam cured at a maximum holding temperature of 55°C. This research also examines the resistance to delayed ettringite formation when the concrete is steam cured at 70°C and 82°C and its secondary consequences on the freeze-thaw resistance. The effect of several experimental variables related to the concrete mix design and also the curing conditions are examined, namely: limestone filler fineness, limestone filler content, cement type, steam curing duration and steam curing temperature. In general, the results reveal that self-consolidating concrete containing 15% limestone filler, steam cured at 55°C, 70°C and 82°C, exhibited similar or superior mechanical and transport properties as well as long term durability performance compared to similar concrete without limestone filler. When the concrete is steam cured at 55°C, the chemical reactivity of limestone filler has an important role in enhancing the mechanical properties at 16 hours (compared to the concrete without limestone filler) and compensating for the dilution effect at 28 days. Although, at 300 days, the expansion of all concrete mixes are below 0.05%, the corresponding freeze-thaw durability factors vary widely and are controlled by the steam curing temperature and the chemical composition of the cement. Overall, the material properties indicate that the use

  8. Factors involved in the selection of limestone reagents for use in wet FGD systems

    International Nuclear Information System (INIS)

    Jarvis, J.B.; Roothaan, E.S.; Meserole, F.B.; Owens, D.R.

    1992-01-01

    With recent activity in the design and construction of retrofit flue gas desulfurization (FGD) systems, many utilities are faced with the task of selecting limestones which will allow FGD systems to function as designed, and at the same time, provide cost-effective operation. The Electric Power Research Institute (EPRI) has sponsored research to identify factors which should be considered in the reagent selection process. A set of capabilities has been developed which is currently being employed to assist six utilities in selecting cost-effective reagent sources. The major elements in the selection package consist of an analytical characterization of candidate limestones; grindability, reactivity, and magnesium availability testing; and performance modeling utilizing EPRI's FGD PRocess Integration and Simulation Model (FGDPRISM). The results from these measurements are used to perform a site-specific economic analysis which can be used to rank the candidate limestones and quantify the impact of various limestone properties on plant operating costs. This paper includes a description of each element in the selection package along with a review of current research activities aimed at improving predictions of limestone reactivity and magnesium availability. An example is presented which illustrates how reactivity and magnesium availability affect both the performance of an FGD system and plant operating costs

  9. Ruminal degradation of dry matter and neutral detergent fiber of banana peel treated with limestone

    Directory of Open Access Journals (Sweden)

    Flávio Pinto Monção

    2016-02-01

    Full Text Available This study aimed to evaluate the kinetics of dry matter degradation and neutral detergent fiber of banana peel treated with limestone. The banana peel has been acquired from a candy manufacturer that after washing with chlorinated water to 1% and pulp removal was discarded. The banana peel in nature was treated with 1, 2, 3 and 4% of limestone in the natural matter, homogenized and pre-dried in the sun for 120 hours. The experiment was conducted in a completely randomized experimental design, with five treatments (0 (control, 1, 2, 3 and 4% inclusion of limestone with 3 repetitions. The dry matter potential degradability, showed no difference (P>0.05 in the levels compared to the control with an average of 67.58%. The insoluble degradation fraction rate of dry matter and the fiber fraction did not differ (P> 0.05 between levels and control. In relation to effective degradability of neutral detergent fiber, there was an increase of 3.47% for each percentage unit increased limestone. In relation to the ruminal degradation parameters of dry matter and neutral detergent fiber is not recommended the utilization of limestone as an additive in the treatment of banana peel.

  10. Gamma radiation influence on Cladonia substellata (lichen) and its effects on limestone rocks

    International Nuclear Information System (INIS)

    Silva, Helena P. de B.; Colaco, Waldeciro; Pereira, Eugenia C.; Silva, Nicacio H. da

    2009-01-01

    The lichens play an important role in decomposition of the rocky substrate, through the chemical weathering of their substances. This work aimed to determine the influence of gamma Ray on usnic acid production of Cladonia substellata and the influence of chelates formation in limestone rocks. Samples with 2.5 g of C. substellata were packed on paper envelopes for irradiation submission to gamma on a Co-60 source. They received 10 different doses: 5, 7, 10, 15, 20, 30, 40, 50, 60 and 80 Gy. Lichen irradiation was conducted on the gamma irradiator (Co-60), and packed over powdered limestone. Lichen samples were analyzed by High Performance Liquid Chromatography (HPLC) and rocky samples by X-Ray Diffractometry. The X-ray diffractogram obtained from the analysis of limestone not subjected to the action of lichen - control sample was compared with limestone subjected to C. substellata irradiated at doses 10, 30 and 80Gy. Increased production of the usnic acid and changes on the rocky samples were noted. We realized that C. substellata increments the usnic acid biosynthesis as the gamma radiation dose is increased, but there is a limit to it. The chelating effect of the usnic acid on limestone was proportional to the produced amount of the substance, which could be extrapolated to natural conditions, where excessive radiation may influence pedogenesis and ecological succession. (author)

  11. Microfacies and Diagenetic Fabric of the Lockhart Limestone, Kotal Pass Section, Northeast of Kohat, Pakistan

    Directory of Open Access Journals (Sweden)

    Muhammad Waseem Khan

    2016-06-01

    Full Text Available The present study is intended to describe the carbonate microfacies of the Paleocene Lockhart Limestone in area northeast of the Kohat City. The analyzed limestone in the area is 65m thick and predominantly medium to thick bedded, nodular to brecciated and richly fossiliferous. Thin interbeds of marl are observed in the main lithological unit. The lower contact of the Lockhart Limestone is faulted with the Samana Suk Formation of the Jurassic age while conformably overlain by the Patala Formation of Paleocene to Eocene age. The major lithological unit is comprised of predominant assemblage of larger benthic and smaller planktonic foraminifers with accretion of ostracods, dasycladacean algae, echinoderms, gastropods and corals. On the basis of field and laboratory observations, two distinct types of microfacies have been identified as i Dasyclad-Miliolid Foram Wacke-Packstone microfacies of the inner shelf, sub tidal lagoon, ii Larger Foram Packstone microfacies of the middle shelf. The Limestone represents a carbonate cyclic sequence marked by three, transgressive, deepening up cycles representing a gradual sea level rise compensated by vertical accumulation of microfacies. The commencement of each cycle is clearly marked by the input of land-derived siliciclastic sediments and near shore restricted marine faunal/floral assemblage in the inner shelf microfacies gradually thinning up section where the microfacies become deeper offshore. The diagenetic modifications are observed in the shape of compactional framework, dolomitization, aragonite to calcite alteration and spar filled fractures in the main lithological unit of the Lockhart Limestone.

  12. Reclamation of acidic colliery spoil. III. Problems associated with the use of high rates of limestone

    Energy Technology Data Exchange (ETDEWEB)

    Costigan, P A [Univ. of Liverpool, England; Bradshaw, A D; Gemmell, R P

    1982-04-01

    Growth of Trifolium repens in acidic colliery spoil was suppressed by more than 90% when agricultural ground calcitic limestone was applied at above 5 t ha/sup -1/ whereas Lolium perenne was unaffected at rates up to 100 t ha/sup -1/. The inhibitory effect of ground limestone on T. repens was reduced by high phosphorus fertilization and disappeared within 34 weeks of treatment.There was some evidence that high liming caused an imbalance of the Ca/Mg ratio in freshly limed spoil, contribution to growth inhibition. Growth of L. perene was improved and the inhibitory effect on T. repens was alleviated by substituting magnesian limestone (dolomite) for calcitic limestone. Phosphate adsorption of spoil was similar after low and very high limestone applications but increased by 100% after liming at 25 t ha/sup -1/ to pH 5.1.It is suggested that phosphate adsorption at pH 5.1 is caused by freshly precipitated amorphous aluminium hydroxide. The practical implications of the results are discussed.

  13. Actinobacterial diversity in limestone deposit sites in Hundung, Manipur (India and their antimicrobial activities

    Directory of Open Access Journals (Sweden)

    Salam eNimaichand

    2015-05-01

    Full Text Available Studies on actinobacterial diversity in limestone habitats are scarce. This paper reports profiling of actinobacteria isolated from Hundung limestone samples in Manipur, India using ARDRA as the molecular tool for preliminary classification. A total of 137 actinobacteria were clustered into 31 phylotypic groups based on the ARDRA pattern generated and representative of each group was subjected to 16S rRNA gene sequencing. Generic diversity of the limestone isolates consisted of Streptomyces (15 phylotypic groups, Micromonospora (4, Amycolatopsis (3, Arthrobacter (3, Kitasatospora (2, Janibacter (1, Nocardia (1, Pseudonocardia (1 and Rhodococcus (1. Considering the antimicrobial potential of these actinobacteria, 19 showed antimicrobial activities against at least one of the bacterial and candidal test pathogens, while 45 exhibit biocontrol activities against at least one of the rice fungal pathogens. Out of the 137 actinobacterial isolates, 118 were found to have at least one of the three biosynthetic gene clusters (PKS-I, PKS-II, NRPS. The results indicate that 86% of the strains isolated from Hundung limestone deposit sites possessed biosynthetic gene clusters of which 40% exhibited antimicrobial activities. It can, therefore, be concluded that limestone habitat is a promising source for search of novel secondary metabolites.

  14. Impacts of Limestone Multi-particle Size on Production Performance, Egg Shell Quality, and Egg Quality in Laying Hens

    Directory of Open Access Journals (Sweden)

    X. Y. Guo

    2012-06-01

    Full Text Available This experiment was conducted to evaluate the effects of single or multi-particle size limestone on the egg shell quality, egg production, egg quality and feed intake in laying hens. A total of 280 laying hens (ISA brown were used in this 10-wk trial. Laying hens were randomly assigned to 4 treatments with 14 replications per treatment and 5 adjacent cages as a replication (hens were caged individually. The experimental treatments were: i L, basal diet+10% large particle limestone; ii LS1, basal diet+8% large particle limestone+2% small particle limestone; iii LS2, basal diet+6% large particle limestone+4% small particle limestone; iv S, basal diet+10% small particle limestone. The egg production was unaffected by dietary treatments. The egg weight in S treatment was lighter than other treatments (p<0.05. The egg specific gravity in S treatment was lower than other treatments (p<0.05. The eggshell strength and eggshell thickness in S treatment were decreased when compared with other dietary treatments (p<0.05. The laying hens in LS1 and LS2 treatment had a higher average feed intake than the other two treatments (p<0.05. Collectively, the dietary multi-particle size limestone supplementation could be as efficient as large particle size limestone.

  15. Porosity development in the Copper Ridge Dolomite and Maynardville Limestone, Bear Creek Valley and Chestnut Ridge, Tennessee

    International Nuclear Information System (INIS)

    Goldstrand, P.M.; Menefee, L.S.; Dreier, R.B.

    1995-12-01

    Matrix porosity data from deep core obtained in Bear Creek Valley indicate that porosities in the Maynardville Limestone are lithology and depth dependent. Matrix porosities are greater in the Cooper Ridge Dolomite than in the Maynardville Limestone, yet there is no apparent correlation with depth. Two interrelated diagenetic processes are the major controlling factors on porosity development in the Copper Ridge Dolomite and Maynardville Limestone; dissolution of evaporate minerals and dedolomitization. Both of these diagenetic processes produce matrix porosities between 2.1 and 1.3% in the Copper Ridge Dolomite and upper part of the Maynardville Limestone (Zone 6) to depths of approximately 600 ft bgs. Mean matrix porosities in Zones 5 through 2 of the Maynardville Limestone range from 0.8 to 0.5%. A large number of cavities have been intersected during drilling activities in nearly all zones of the Maynardville Limestone in Bear Creek Valley. Therefore, any maynardville Limestone zone within approximately 200 ft of the ground surface is likely to contain cavities that allow significant and rapid flow of groundwater. Zone 6 could be an important stratigraphic unit in the Maynardville Limestone for groundwater flow and contaminant transport because of the abundance of vuggy and moldic porosities. There are large variations in the thickness and lithology in the lower part of the Maynardville (Zones 2, 3, and 4 in the Burial Grounds region). The direction and velocity of strike-parallel groundwater flow may be altered in this area within the lower Maynardville Limestone

  16. [Fish community structure and its seasonal change in subtidal sandy beach habitat off southern Gouqi Island].

    Science.gov (United States)

    Wang, Zhen-Hua; Wang, Kai; Zhao, Jing; Zhang, Shou-Yu

    2011-05-01

    To understand the characteristics of fish community structure in sandy beach habitats of island reef water areas, and to evaluate the potential capacity of these habitats in local fish stock maintenance, fishes were monthly collected with multi-mesh trammel nets in 2009 from the subtidal sandy beach habitat off southern Gouqi Island, taking the adjacent rocky reef habitat as the control. alpha and beta species diversity indices, index of relative importance (IRI), relative catch rate, and dominance curve for abundance and biomass (ABC curve) were adopted to compare the fish species composition, diversity, and community pattern between the two habitats, and multivariate statistical analyses such as non-metric multidimensional scaling (nMDS) and cluster were conducted to discuss the fish assemblage patterns. A total of 63 fish species belonging to 11 orders, 38 families, and 56 genera were collected, of which, 46 fish species were appeared in the two habitats. Due to the appearance of more warm water species in sandy bottom, the fishes in subtidal sandy beach habitat showed much higher richness, and the abundance catch rate (ACR) from May to July was higher than that in rocky reef habitat. In most rest months, the ACR in subtidal sandy beach habitat also showed the similar trend. However, the species richness and diversity in spring and summer were significantly lower in subtidal sandy beach habitat than in rocky reef habitat, because of the high species dominance and low evenness in the sandy beach habitat. Japanese tonguefish (Paraplagusia japonica) was the indicator species in the sandy beach habitat, and dominated in early spring, later summer, autumn, and winter when the fishing pressure was not strong. In sandy bottom, a unique community structure was formed and kept in dynamic, due to the nursery use of sandy beach by Japanese anchovy (Engraulis japonicus) from May to July, the gathering of gray mullet (Mugil cephalus) in most months for feeding, and the large

  17. Migration of cesium-137 through sandy soil layer effect of fine silt on migration

    International Nuclear Information System (INIS)

    Ohnuki, Toshihiko; Wadachi, Yoshiki

    1983-01-01

    The migration of 137 Cs through sandy soil layer was studied with consideration of the migration of fine silt by column method. It was found that a portion of fine silt migrated through the soil layer accompanying with 137 Cs. The mathematical migration model of 137 Cs involved the migration of fine silt through such soil layer was presented. This model gave a good accordance between calculated concentration distribution curve in sandy soil layer and effluent curve and observed those. So, this model seems to be advanced one for evaluating migration of 137 Cs in sandy soil layer with silt. (author)

  18. Properies of binder systems containing cement, fly ash, and limestone powder

    Directory of Open Access Journals (Sweden)

    Krittiya Kaewmanee

    2014-10-01

    Full Text Available Fly ash and limestone powder are two major widely available cement replacing materials in Thailand. However, the current utilization of these materials is still not optimized due to limited information on properties of multi-binder systems. This paper reports on the mechanical and durability properties of mixtures containing cement, fly ash, and limestone powder as single, binary, and ternary binder systems. The results showed that a single binder system consisting of only cement gave the best carbonation resistance. A binary binder system with fly ash exhibited superior performances in long-term compressive strength and many durability properties except carbonation and magnesium sulfate resistances, while early compressive strength of a binary binder system with limestone powder was excellent. The ternary binder system, taking the most benefit of selective cement replacing materials, yielded, though not the best, satisfactory performances in almost all properties. Thus, the optimization of binders can be achieved through a multi-binder system.

  19. A correlation of Sr isotope stratigraphy and foraminiferal biostratigraphy in tertiary limestones of Papua New Guinea

    International Nuclear Information System (INIS)

    Allan, T.L.; Trotter, J.A.; Whitford, D.J.; Korsch, M.J.

    2000-01-01

    Strontium isotopic and stratigraphic data collected from the Darai Limestone of Papua New Guinea clearly demonstrate a systematic relationship between bulk 87 Sr/ 86 Sr ratio and index foraminiferal composition that closely reflects the relative stratigraphical range of the foraminifera in this region. A graphic correlation of stratigraphic, strontium isotopic and age ranges of the major index taxa permits direct evaluation of limestone age and isotopic composition in the Darai Limestone. The age of the Tf 1 /Tf 2 boundary (∼12.2 Ma) is significantly younger than the accepted estimate of ∼15.0 Ma (plankton Zone N9) and the Te/Tf boundary (∼20.3 Ma) is older than the generally accepted age of ∼l 8.5 Ma (plankton Zone N6)

  20. A NEW DAONELLA FROM THE LADINIAN PLATFORM OF THE ESINO LIMESTONE (SOUTHERN ALPS, ITALY

    Directory of Open Access Journals (Sweden)

    CRISTIANO LARGHI

    2006-03-01

    Full Text Available The bivalve Daonella Mojsisovics, 1874 is very common in the Middle Triassic pelagic facies, whereas the record of this genus from shallow water limestones is rare. In the present paper a new species of Daonella, named D. pseudograbensis, is described from the Esino Limestone, a Ladinian (Middle Triassic carbonate platform in the central Southern Alps. The species is described from Brembana Valley, where the Esino Limestone is rather rich in bioclastic lenses yielding faunas with bivalves, cephalopods, gastropods, brachiopods, corals and calcareous algae. Daonella pseudograbensis n. sp. is based on very well preserved specimens, which are often articulated and closed, all coming from the same locality. The new species shows a narrow range of intraspecific and ontogenetic morphologic variations. It is easy distinguishable from the other species of the genus for the outline and ornamentation; it therefore differs from D. grabensis Kittl, 1912, the most similar species, for the longer anterior dorsal margin.Pdf

  1. Successful experience with limestone and other sorbents for combustion of biomass in fluid bed power boilers

    Energy Technology Data Exchange (ETDEWEB)

    Coe, D.R. [LG& E Power Systems, Inc., Irvine, CA (United States)

    1993-12-31

    This paper presents the theoretical and practical advantages of utilizing limestone and other sorbents during the combustion of various biomass fuels for the reduction of corrosion and erosion of boiler fireside tubing and refractory. Successful experiences using a small amount of limestone, dolomite, kaolin, or custom blends of aluminum and magnesium compounds in fluid bed boilers fired with biomass fuels will be discussed. Electric power boiler firing experience includes bubbling bed boilers as well as circulating fluid bed boilers in commercial service on biomass fuels. Forest sources of biomass fuels fired include wood chips, brush chips, sawmill waste wood, bark, and hog fuel. Agricultural sources of biomass fuels fired include grape vine prunings, bean straw, almond tree chips, walnut tree chips, and a variety of other agricultural waste fuels. Additionally, some urban sources of wood fuels have been commercially burned with the addition of limestone. Data presented includes qualitative and quantitative analyses of fuel, sorbent, and ash.

  2. Modelling of catalytic oxidation of NH3 and reduction of NO on limestone during sulphur capture

    DEFF Research Database (Denmark)

    Kiil, Søren; Bhatia, Suresh K.; Dam-Johansen, Kim

    1996-01-01

    activity with respect to each species involved. An existing particle model, the Grain-Micrograin Model, which simulates sulphur capture on limestone under oxidizing conditions is considered in the modelling. Simulation results in good qualitative agreement with experimental data are obtained here......A theoretical study of the complex transient system of simultaneous sulphur capture and catalytic reactions of N-containing compounds taking place on a single limestone particle is conducted. The numerical technique developed previously by the authors (Kiil et al. 1994) based on collocation...... for the catalytic chemistry of NH3 during simultaneous sulphur capture on a Stevns Chalk particle. The reduction of NO by NH3 over CaSO4 (which is the product of the reaction between SO2, O2 and limestone) was found to be important because this reaction could explain the change in selectivity with increased solid...

  3. Epilithic and endolithic bacterial communities in limestone from a Maya archaeological site.

    Science.gov (United States)

    McNamara, Christopher J; Perry, Thomas D; Bearce, Kristen A; Hernandez-Duque, Guillermo; Mitchell, Ralph

    2006-01-01

    Biodeterioration of archaeological sites and historic buildings is a major concern for conservators, archaeologists, and scientists involved in preservation of the world's cultural heritage. The Maya archaeological sites in southern Mexico, some of the most important cultural artifacts in the Western Hemisphere, are constructed of limestone. High temperature and humidity have resulted in substantial microbial growth on stone surfaces at many of the sites. Despite the porous nature of limestone and the common occurrence of endolithic microorganisms in many habitats, little is known about the microbial flora living inside the stone. We found a large endolithic bacterial community in limestone from the interior of the Maya archaeological site Ek' Balam. Analysis of 16S rDNA clones demonstrated disparate communities (endolithic: >80% Actinobacteria, Acidobacteria, and Low GC Firmicutes; epilithic: >50% Proteobacteria). The presence of differing epilithic and endolithic bacterial communities may be a significant factor for conservation of stone cultural heritage materials and quantitative prediction of carbonate weathering.

  4. Thermochemical degradation of limestone aggregate concrete on exposure to sodium fire

    International Nuclear Information System (INIS)

    Premila, M.; Sivasubramanian, K.; Amarendra, G.; Sundar, C.S.

    2008-01-01

    Limestone aggregate concrete blocks were subjected to sodium fire conforming to a realistic scenario in order to qualify them as protective sacrificial layers over structural concrete flooring in liquid metal-cooled fast breeder reactors. Mid infrared absorption measurements were carried out on these sodium fire-exposed samples as a function of depth from the affected surface. Definite signatures of thermochemical degradation indicating dehydration and structural modification of the limestone concrete have been obtained. Control runs were carried out to delineate the thermal effects of sodium fires from that of the chemical interaction effects. Measurements on limestone aggregate samples treated with fused NaOH provided direct evidence of the exact mechanism of the sodium attack on concrete. The observed degradation effects were correlated to the mechanical strength of the concrete blocks and to the intensity of the sodium fire experienced

  5. Elemental analysis of some West Malaysian limestones using neutron activation, delayed neutron and electron microprobe analysis

    International Nuclear Information System (INIS)

    Amin, Y.M.; Kamaluddin, B.; Mahat, R.H.

    1990-01-01

    Limestone stratigraphy in Malaysia has been and is dependent almost entirely in palaeontology. However fossil localities are sporadic and as such a new fossil discovery mean the necessity for a complete re-appraisal of the stratigraphy. The almost complete dependence upon palaeontology results from the difficulties of stratigraphy correlation of isolated outcrops, from the cover of tropical vegetation and from the often complex folding and faulting which has been imposed on the geosyn-clinical rocks by the Indonesian-Thai-Malayan orogeny. So by studying the elemental composition of limestones accurately, we would be able to correlate outcrops and other stratigraphic samples independent of fossil finds. The use of delayed neutron analysis would also determine the concentration of uranium and thorium accurately. This study, in conjunction with thermoluminescence and fission track studies, would able us to date the age of the limestones

  6. Industrial application of limestone deposits of kohat, NWFP: a research towards the sustainability of the deposits

    International Nuclear Information System (INIS)

    Bilqees, R.; Shah, T.

    2007-01-01

    Chemical analyses, petrographic studies and physical tests of limestone deposits in the vicinity of kohat along Bannu Road, Hangu Road and Rawalpindi Road were carried out to categorize these reserves, locality-wise, for their specified industrial uses. Limestone of kohat area was found to be generally good for construction purposes. The deposits on the Hangu Road were of good quality with more then 97% CaCO/sub 3/ and suitable for use in chemical, iron and steel industries, for glass making, soda ash manufacture etc. The deposit of Bannu Road with 96.5% CaCO/sub 3/ can be used for sugar refining, paint industry, flue gas desulphurization, animal feed etc. The limestone deposit of Rawalpindi Road is inferior in quality having 95.2% CaCO/sub 3/. It can be utilized in rubber industry, as ceramic whiting, building materials, rock wool etc. (author)

  7. Early Dialysis and Adverse Outcomes After Hurricane Sandy.

    Science.gov (United States)

    Lurie, Nicole; Finne, Kristen; Worrall, Chris; Jauregui, Maria; Thaweethai, Tanayott; Margolis, Gregg; Kelman, Jeffrey

    2015-09-01

    Hemodialysis patients have historically experienced diminished access to care and increased adverse outcomes after natural disasters. Although "early dialysis" in advance of a storm is promoted as a best practice, evidence for its effectiveness as a protective measure is lacking. Building on prior work, we examined the relationship between the receipt of dialysis ahead of schedule before the storm (also known as early dialysis) and adverse outcomes of patients with end-stage renal disease in the areas most affected by Hurricane Sandy. Retrospective cohort analysis, using claims data from the Centers for Medicare & Medicaid Services Datalink Project. Patients receiving long-term hemodialysis in New York City and the state of New Jersey, the areas most affected by Hurricane Sandy. Receipt of early dialysis compared to their usual treatment pattern in the week prior to the storm. Emergency department (ED) visits, hospitalizations, and 30-day mortality following the storm. Of 13,836 study patients, 8,256 (60%) received early dialysis. In unadjusted logistic regression models, patients who received early dialysis were found to have lower odds of ED visits (OR, 0.75; 95% CI, 0.63-0.89; P=0.001) and hospitalizations (OR, 0.77; 95% CI, 0.65-0.92; P=0.004) in the week of the storm and similar odds of 30-day mortality (OR, 0.80; 95% CI, 0.58-1.09; P=0.2). In adjusted multivariable logistic regression models, receipt of early dialysis was associated with lower odds of ED visits (OR, 0.80; 95% CI, 0.67-0.96; P=0.01) and hospitalizations (OR, 0.79; 95% CI, 0.66-0.94; P=0.01) in the week of the storm and 30-day mortality (OR, 0.72; 95% CI, 0.52-0.997; P=0.048). Inability to determine which patients were offered early dialysis and declined and whether important unmeasured patient characteristics are associated with receipt of early dialysis. Patients who received early dialysis had significantly lower odds of having an ED visit and hospitalization in the week of the storm and of

  8. Sedimentary and environmental history of the Late Permian Bonikowo Reef (Zechstein Limestone, Wuchiapingian, western Poland

    Directory of Open Access Journals (Sweden)

    Paweł Raczyński

    2017-07-01

    Full Text Available The Bonikowo Reef occurs in the central part of the Zechstein Limestone Basin in western Poland and was growing on the topmost edges of tilted blocks and/or on the top of uplifted horsts of the Brandenburg–Wolsztyn–Pogorzela High. Its size is ca. 1.6 km2. The Bonikowo Reef shows the thickest reef section (90.5 m recorded in the High. The Zechstein Limestone unit is represented mostly by limestones, often thoroughly recrystallized, although the macrotextures and biota of the boundstone are identifiable in most cases. The drillcore section is a mixture of boundstones (microbial and bryozoan, wackestones, packstones and grainstones, which often co-occur. The δ13C and δ18O values for both calcite (avg. 3.8 ± 0.8‰ and −3.4 ± 1.7‰, respectively and dolomite (avg. 3.5 ± 0.7‰ and −5.2 ± 1.3‰, respectively are transitional between the values previously reported for condensed sequences of the basinal facies and larger reef complexes. The biofacies of the Bonikowo Reef are very similar to those recognized in other reefs of the Brandenburg–Wolsztyn–Pogorzela High, which owe their origin to the destruction of bryozoan boundstones. The biota composition is typical and characteristic of other Zechstein Limestone reefs. However, the Bonikowo Reef demonstrates the importance of microbialites, laminar and nodose encrustations, in the growth and cohesion of the Zechstein Limestone reefs. Such encrustations abound within the Zechstein Limestone although, in many cases, the real nature of the encrustations is difficult to ascertain. These laminated encrustations show great similarity to Archaeolithoporella that is one of the most important Permian reef-building organisms. The encrustations considered to represent Archaeolithoporella were also previously recorded in the Zechstein Limestone of western Poland and in its stratigraphic equivalent, the Middle Magnesian Limestone of Northeast England. The lower part of the sequence shows

  9. Pliocene Te Aute limestones, New Zealand : expanding concepts for cool-water shelf carbonates

    International Nuclear Information System (INIS)

    Nelson, C.S.; Winefield, P.R.; Hood, S.D.; Caron, V.; Pallentin, A.; Kamp, P.J.J.

    2003-01-01

    Acceptance of a spectrum of warm- through cold-water shallow-marine carbonate facies has become of fundamental importance for correctly interpreting the origin and significance of all ancient platform limestones. Among other attributes, properties that have become a hallmark for characterising many Cenozoic non-tropical occurrences include: (1) the presence of common bryozoan and epifaunal bivalve skeletons; (2) a calcite-dominated mineralogy; (3) relatively thin deposits exhibiting low rates of sediment accumulation; (4) an overall destructive early diagenetic regime; and (5) that major porosity destruction and lithification occur mainly in response to chemical compaction of calcitic skeletons during moderate to deep burial. The Pliocene Te Aute limestones are non-tropical skeletal carbonates formed at paleolatitudes near 40-42 degrees S under the influence of commonly strong tidal flows along the margins of an actively deforming and differentially uplifting forearc basin seaway, immediately inboard of the convergent Pacific-Australian plate boundary off eastern North Island, New Zealand. This dynamic depositional and tectonic setting strongly influenced both the style and subsequent diagenetic evolution of the limestones. Some of the Te Aute limestones exhibit the above kinds of 'normal' non-tropical characteristics, but others do not. For example, many are barnacle and/or bivalve dominated, and several include attributes that at least superficially resemble properties of certain tropical carbonates. In this regard, a number of the limestones are infaunal bivalve rich and dominated by an aragonite over a calcite primary mineralogy, with consequently relatively high diagenetic potential. Individual limestone units are also often rather thick (e.g., up to 50-300 m), with accumulation rates from 0.2 to 0.5 m/ka, and locally as high as 1 m/ka. Moreover, there can be a remarkable array of diagenetic features in the limestones, involving grain alteration and

  10. Rapid method to determine actinides and 89/90Sr in limestone and marble samples

    International Nuclear Information System (INIS)

    Maxwell, S.L.; Culligan, Brian; Hutchison, J.B.; Utsey, R.C.; Sudowe, Ralf; McAlister, D.R.

    2016-01-01

    A new method for the determination of actinides and radiostrontium in limestone and marble samples has been developed that utilizes a rapid sodium hydroxide fusion to digest the sample. Following rapid pre-concentration steps to remove sample matrix interferences, the actinides and 89 / 90 Sr are separated using extraction chromatographic resins and measured radiometrically. The advantages of sodium hydroxide fusion versus other fusion techniques will be discussed. This approach has a sample preparation time for limestone and marble samples of <4 h. (author)

  11. Improvement of operational properties of shell limestone building materials by polysulfide solution impregnation

    Directory of Open Access Journals (Sweden)

    MASSALIMOV Ismail Alexandrovich

    2017-06-01

    Full Text Available The data of studies on the effectiveness of impregnation with polysulfide solutions of shell limestone used as facing and wall material, as well as for the manufacture of road products are presented. Modification of the limestone with the impregnating composition «Akvastat» created by the authors which is sulfur-containing water-based solution of calcium polysulfide containing alcohols and surfactants, can significantly reduce water absorption and increase durability of limestone. Impregnating composition on the basis of calcium polysulfide possesses density of 1.22–1.24 g/cm3, the infiltrant penetrates into the pore structure of limestone to a depth of 4 cm or more, depending on the density and structure of the sample. While the material is drying, sulfur nanoparticles are crystallized from the polysulfide solution in its pores. They partially fill pore space and form protective durable insoluble hydrophobic coating that impedes the penetration of water into the pores of the limestone, but preserves its vapor permeability, which is important for wall and decoration materials. The evaluation of protective coatings was performed with laser particle size analyzer, scanning probe microscope and a diffractometer. It showed that the average size of the particles forming the protective coating is in the range of 20–25 nm, the particles shape is spherical, the particles are elemental sulfur with orthorhombic structure of the crystal lattice. The processing of shell limestone with calcium polysulphide solution provides formation of coating based on nanosized sulfur on the surface of stone pores. The coating partially fills the pore space and, as it is hydrophobic, reduces the water absorption of the samples by a factor of 5–8, increases their average density by 22–27%, strength in 1,2–1,3 times, the softening factor by 6–19%, that makes possible to predict the increase of the durability of building materials based on shell limestone to 1

  12. Performance of japanese quails fed feeds containing different corn and limestone particle sizes

    OpenAIRE

    Berto,DA; Garcia,EA; Móri,C; Faitarone,ABG; Pelícia,K; Molino,AB

    2007-01-01

    This study aimed at evaluating performance and egg quality of Japanese quails fed feeds containing different corn and limestone particle sizes. A total number of 648 birds in the peak of production was distributed in a random complete block experimental design, using a 2x3 factorial arrangement (2 corn particle sizes and 3 limestone particle sizes). Birds were designated to one of two blocks, with six replicates of 18 birds each. Mean geometric diameter (MGD) values used were 0.617mm and 0.72...

  13. Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone

    DEFF Research Database (Denmark)

    Moesgaard, M; Poulsen, Søren Lundsted; Herfort, D

    2012-01-01

    M. MOESGAARD, S.L. POULSEN, D. HERFORT, M. STEENBERG, L.F. KIRKEGAARD, J. SKIBSTED, Y. YUE, Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone, Journal of the American Ceramic Society 95, 403 – 409 (2012).......M. MOESGAARD, S.L. POULSEN, D. HERFORT, M. STEENBERG, L.F. KIRKEGAARD, J. SKIBSTED, Y. YUE, Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone, Journal of the American Ceramic Society 95, 403 – 409 (2012)....

  14. Differences between silica and limestone concretes that may affect their interaction with corium

    International Nuclear Information System (INIS)

    Journeau, C.; Haquet, J. F.; Piluso, P.; Bonnet, J. M.

    2008-01-01

    Recent Molten Core Concrete Interaction tests performed at Argonne National Laboratory and at CEA Cadarache have shown that, whereas the ablation of limestone-rich concretes is almost isotropic, the ablation of silica-rich concretes is much faster towards the sides than towards the bottom of the cavity. The following differences exists between limestone-rich and silica-rich concretes: limestone concretes liberate about twice as much gas, at a given ablation rate than siliceous concretes (more than 50% more at constant heat flux) and this can affect pool hydraulics and crust stability: limestone concrete has a higher liquidus temperature than siliceous concrete and molten limestone concrete has a larger diffusion coefficient and can more easily dissolve a corium crust than siliceous melt; limestone aggregates are destroyed by de-carbonation at around 1000 K while silica aggregates melt only above 2000 K, so that floating silica aggregates can form cold spots increasing corium solidification near the interface; de-carbonation of limestone leads to a significant shrinkage of concrete melt volume compared to the cold solid that hampers the mechanical stability of overlying crusts; the chemical composition of molten mortar (sand + cement) and concrete (sand + gravel + cement) is close for limestone-rich concretes while it is different for siliceous concretes, so that the melt composition may vary significantly in case of non-simultaneous melting of the siliceous concrete constituents; molten silicates have a large viscosity, so that transport properties are different for the two types of concretes. The small range of plant concrete compositions that have been considered for MCCI experiments has not yet been found sufficient to determine which of the above-mentioned differences is paramount to explain the observed difference in ablation patterns. Separate Effect Tests using specially-designed 'artificial concretes' and prototypic corium would provide the necessary

  15. Carbonate Minerals with Magnesium in Triassic Terebratula Limestone in the Term of Limestone with Magnesium Application as a Sorbent in Desulfurization of Flue Gases

    Science.gov (United States)

    Stanienda-Pilecki, Katarzyna

    2017-09-01

    This article presents the results of studies of Triassic (Muschelkalk) carbonate rock samples of the Terebratula Beds taken from the area of the Polish part of the Germanic Basin. It is the area of Opole Silesia. The rocks were studied in the term of possibility of limestone with magnesium application in desulfurization of flue gases executed in power plants. Characteristic features of especially carbonate phases including magnesium-low-Mg calcite, high-Mg calcite, dolomite and huntite were presented in the article. They were studied to show that the presence of carbonate phases with magnesium, especially high-Mg calcite makes the desulfurization process more effective. Selected rock samples were examined using a microscope with polarized, transmitted light, X-ray diffraction, microprobe measurements and FTIR spectroscopy. The results of studies show a domination of low magnesium calcite in the limestones of the Terebratula Beds. In some samples dolomite and lower amounts of high-Mg calcite occurred. Moreover, huntite was identified. The studies were very important, because carbonate phases like high-Mg calcite and huntite which occurred in rocks of the Triassic Terebratula Beds were not investigated in details by other scientists but they presence in limestone sorbent could influence the effectiveness of desulfurization process.

  16. Content Analysis of Select YouTube Postings: Comparisons of Reactions to the Sandy Hook and Aurora Shootings and Hurricane Sandy.

    Science.gov (United States)

    Miller, Eric D

    2015-11-01

    This study details an innovative and methodical content analysis of 2,207 YouTube comments from four different YouTube videos (e.g., breaking news or memorials) related to the 2012 Sandy Hook Elementary School and Aurora theater mass shootings and the catastrophic Hurricane Sandy. As expected, YouTube comments associated with the Sandy Hook shootings (particularly those from a memorial video) were especially likely to feature compassion and grief with lessened hostility. This study highlights differing online contexts by which individuals show grief and related emotions following man-made and natural calamities and how-even in an online environment-powerful situational contexts greatly guide behavior.

  17. Phosphorus fractions in sandy soils of vineyards in southern Brazil

    Directory of Open Access Journals (Sweden)

    Djalma Eugênio Schmitt

    2013-04-01

    Full Text Available Phosphorus (P applications to vineyards can cause P accumulation in the soil and maximize pollution risks. This study was carried out to quantify the accumulation of P fractions in sandy soils of vineyards in southern Brazil. Soil samples (layers 0-5, 6-10 and 11-20 cm were collected from a native grassland area and two vineyards, after 14 years (vineyard 1 and 30 years (vineyard 2 of cultivation, in Santana do Livramento, southern Brazil, and subjected to chemical fractionation of P. Phosphorus application, especially to the 30-year-old vineyard 2, increased the inorganic P content down to a depth of 20 cm, mainly in the labile fractions extracted by anion-exchange resin and NaHCO3, in the moderately labile fraction extracted by 0.1 and 0.5 mol L-1 NaOH, and in the non-labile fraction extracted by 1 mol L-1 HCl, indicating the possibility of water eutrophication. Phosphorus application and grapevine cultivation time increased the P content in the organic fraction extracted by NaHCO3 from the 0-5 cm layer, and especially in the moderately labile fraction extracted by 0.1 mol L-1 NaOH, down to a depth of 20 cm.

  18. Spatial variability of macrobenthic zonation on exposed sandy beaches

    Science.gov (United States)

    Veiga, Puri; Rubal, Marcos; Cacabelos, Eva; Maldonado, Cristina; Sousa-Pinto, Isabel

    2014-07-01

    We analysed the consistence of vertical patterns of distribution (i.e. zonation) for macrofauna at different spatial scales on four intermediate exposed beaches in the North of Portugal. We tested the hypothesis that biological zonation on exposed sandy beaches would vary at the studied spatial scales. For this aim, abundance, diversity and structure of macrobenthic assemblages were examined at the scales of transect and beach. Moreover, the main environmental factors that could potentially drive zonation patterns were investigated. Univariate and multivariate analyses revealed that the number of biological zones ranged from two to three depending on the beach and from indistinct zonation to three zones at the scale of transect. Therefore, results support our working hypothesis because zonation patterns were not consistent at the studied spatial scales. The median particle size, sorting coefficient and water content were significantly correlated with zonation patterns of macrobenthic assemblages. However, a high degree of correlation was not reached when the total structure of the assemblage was considered.

  19. Effects of leachate on geotechnical characteristics of sandy clay soil

    Science.gov (United States)

    Harun, N. S.; Ali, Z. Rahman; Rahim, A. S.; Lihan, T.; Idris, R. M. W.

    2013-11-01

    Leachate is a hazardous liquid that poses negative impacts if leaks out into environments such as soil and ground water systems. The impact of leachate on the downgraded quality in terms of chemical characteristic is more concern rather than the physical or mechanical aspect. The effect of leachate on mechanical behaviour of contaminated soil is not well established and should be investigated. This paper presents the preliminary results of the effects of leachate on the Atterberg limit, compaction and shear strength of leachate-contaminated soil. The contaminated soil samples were prepared by mixing the leachate at ratiosbetween 0% and 20% leachate contents with soil samples. Base soil used was residual soil originated from granitic rock and classified as sandy clay soil (CS). Its specific gravity ranged between 2.5 and 2.64 with clay minerals of kaolinite, muscovite and quartz. The field strength of the studied soil ranged between 156 and 207 kN/m2. The effects of leachate on the Atterberg limit clearly indicated by the decrease in liquid and plastic limit values with the increase in the leachate content. Compaction tests on leachate-contaminated soil caused the dropped in maximum dry density, ρdry and increased in optimum moisture content, wopt when the amount of leachate was increased between 0% and 20%. The results suggested that leachate contamination capable to modify some geotechnical properties of the studied residual soils.

  20. Exploring the social dimension of sandy beaches through predictive modelling.

    Science.gov (United States)

    Domínguez-Tejo, Elianny; Metternicht, Graciela; Johnston, Emma L; Hedge, Luke

    2018-05-15

    Sandy beaches are unique ecosystems increasingly exposed to human-induced pressures. Consistent with emerging frameworks promoting this holistic approach towards beach management, is the need to improve the integration of social data into management practices. This paper aims to increase understanding of links between demographics and community values and preferred beach activities, as key components of the social dimension of the beach environment. A mixed method approach was adopted to elucidate users' opinions on beach preferences and community values through a survey carried out in Manly Local Government Area in Sydney Harbour, Australia. A proposed conceptual model was used to frame demographic models (using age, education, employment, household income and residence status) as predictors of these two community responses. All possible regression-model combinations were compared using Akaike's information criterion. Best models were then used to calculate quantitative likelihoods of the responses, presented as heat maps. Findings concur with international research indicating the relevance of social and restful activities as important social links between the community and the beach environment. Participant's age was a significant variable in the four predictive models. The use of predictive models informed by demographics could potentially increase our understanding of interactions between the social and ecological systems of the beach environment, as a prelude to integrated beach management approaches. The research represents a practical demonstration of how demographic predictive models could support proactive approaches to beach management. Copyright © 2018 Elsevier Ltd. All rights reserved.

  1. Field sampling of residual aviation gasoline in sandy soil

    International Nuclear Information System (INIS)

    Ostendorf, D.W.; Hinlein, E.S.; Yuefeng, Xie; Leach, L.E.

    1991-01-01

    Two complementary field sampling methods for the determination of residual aviation gasoline content in the contaminated capillary fringe of a fine, uniform, sandy soil were investigated. The first method featured field extrusion of core barrels into pint-size Mason jars, while the second consisted of laboratory partitioning of intact stainless steel core sleeves. Soil samples removed from the Mason jars (in the field) and sleeve segments (in the laboratory) were subjected to methylene chloride extraction and gas chromatographic analysis to compare their aviation gasoline content. The barrel extrusion sampling method yielded a vertical profile with 0.10m resolution over an essentially continuous 5.0m interval from the ground surface to the water table. The sleeve segment alternative yielded a more resolved 0.03m vertical profile over a shorter 0.8m interval through the capillary fringe. The two methods delivered precise estimates of the vertically integrated mass of aviation gasoline at a given horizontal location, and a consistent view of the vertical profile as well. In the latter regard, a 0.2m thick lens of maximum contamination was found in the center of the capillary fringe, where moisture filled all voids smaller than the mean pore size. The maximum peak was resolved by the core sleeve data, but was partially obscured by the barrel extrusion observations, so that replicate barrels or a half-pint Mason jar size should be considered for data supporting vertical transport analyses in the absence of sleeve partitions

  2. Measurement of indoor and outdoor radon concentrations during Superstorm Sandy.

    Science.gov (United States)

    Kotrappa, Payasada; Paul, Prateek; Stieff, Alex; Stieff, Frederick

    2013-12-01

    Superstorm Sandy affected much of the US East Coast extending over 1800 km. It passed over the test location in the State of Maryland on 29 October 2012. Being 350 km away from the regions of highest intensity the storm was of lower intensity at the test location. Continuous radon monitors and passive radon monitors were used for the measurement. The test location was the basement of a single family home representing the indoor concentration. A partially opened garage of the same test home represented the outdoor radon concentration. In 24 h, the atmospheric pressure dropped from 990 to 960 mbar and the indoor radon concentration increased from 70 to 1500 Bq m(-3) and returned to the normal of 70 Bq m(-3) at the end of the storm. Throughout the storm, the outdoor radon concentration was not significantly affected. Probable reasons for such surprisingly large changes are discussed. However, the outdoor temperature dropped from 13°C to 7°C during the radon peak.

  3. Thermomechanical Behavior of Energy Pile Embedded in Sandy Soil

    Directory of Open Access Journals (Sweden)

    Xu Huang

    2018-01-01

    Full Text Available The traditional energy pile (solid energy pile has been implemented for decades. However, the design of different kinds of energy piles is still not well understood. In this study, a series of model tests were performed on an aluminum pipe energy pile (PEP in dry sandy soil to investigate the thermal effects on the mechanical behaviors of pipe energy pile. The thermal responses of the PEP were also analyzed. Steady temperatures of the PEP under different working conditions were also compared with that of the solid energy pile. Different loading tests were carried out on four pipe energy piles under three different temperatures of 5, 35, and 50°C, respectively. The bearing capacity change can be interpreted through the load-displacement curves. Experiment results were also compared with the solid energy pile to evaluate bearing capacities of the PEP and the solid energy pile under different temperature conditions. The mobilized shaft resistance was also calculated and compared with the solid energy pile data and the results show that the PEP has a similar load transfer mechanism with the solid energy pile. It could also be found that, for PEPs under working load, plastic displacement would appear after a whole heating cycle.

  4. Evaluation of the Intel Sandy Bridge-EP server processor

    CERN Document Server

    Jarp, S; Leduc, J; Nowak, A; CERN. Geneva. IT Department

    2012-01-01

    In this paper we report on a set of benchmark results recently obtained by CERN openlab when comparing an 8-core “Sandy Bridge-EP” processor with Intel’s previous microarchitecture, the “Westmere-EP”. The Intel marketing names for these processors are “Xeon E5-2600 processor series” and “Xeon 5600 processor series”, respectively. Both processors are produced in a 32nm process, and both platforms are dual-socket servers. Multiple benchmarks were used to get a good understanding of the performance of the new processor. We used both industry-standard benchmarks, such as SPEC2006, and specific High Energy Physics benchmarks, representing both simulation of physics detectors and data analysis of physics events. Before summarizing the results we must stress the fact that benchmarking of modern processors is a very complex affair. One has to control (at least) the following features: processor frequency, overclocking via Turbo mode, the number of physical cores in use, the use of logical cores ...

  5. Field experiment on multicomponent ion exchange in a sandy aquifer

    International Nuclear Information System (INIS)

    Bjerg, P.L.; Christensen, T.H.

    1990-01-01

    A field experiment is performed in a sandy aquifer in order to study ion exchange processes and multicomponent solute transport modeling. An injection of groundwater spiked with sodium and potassium chloride was performed over a continuous period of 37 days. The plume is monitored by sampling 350 filters in a spatial grid. The sampling aims at establishing compound (calcium, magnesium, potassium, sodium, chloride) breakthrough curves at various filters 15 to 100 m from the point of injection and areal distribution maps at various cross sections from 0 to 200 m from the point of injection. A three-dimensional multicomponent solute transport model will be used to model the field experiments. The chemical model includes cation exchange, precipitation, dissolution, complexation, ionic strength and the carbonate system. Preliminary results from plume monitoring show that the plume migration is relatively well controlled considering the scale and conditions of the experiment. The transverse dispersion is small causing less dilution than expected. The ion exchange processes have an important influence on the plume composition. Retardation of the injected ions is substantial, especially for potassium. Calcium exhibits a substantial peak following chloride due to release from the ion exchange sites on the sediment. (Author) (8 refs., 5 figs., tab.)

  6. Diagenetic evolution and stable isotopes of Lower Permian platform marginal carbonates (Trogkofel Limestone, Carnic Alps, Austria)

    Science.gov (United States)

    Schaffhauser, Maria; Krainer, Karl; Sanders, Diethard Gerald; Spötl, Christoph

    2010-05-01

    The Trogkofel massif in the Carnic Alps, Austria/Italy, consists of a succession up to 400 m thick of limestones deposited along a platform margin (Trogkofel Limestone; Artinskian). The top of the Trogkofel Limestone is erosively overlain by the Tarvis Breccia. Up-section, the Trogkofel Limestone consists of well-bedded shallow-water bioclastic limestones with intercalated mud mounds, overlain by thick-bedded to unbedded limestones (bioclastic grainstones, packstones, rudstones) and cementstone mounds rich in phylloid algae, Tubiphytes, bryozoans and Archaeolithoporella. In the cementstone mounds, bioclasts are coated by thick fringes and botryoids of fibrous calcite, and of calcite spar that probably represents calcitized aragonite. Primary and intrinsic pores are filled by microbialite, and/or by mudstone to bioclastic wackestone. Shallow-water bioclastic grainstones are cemented by isopachous fringes of fibrous calcite, or by sparry calcite. Throughout the succession, evidence for meteoric-vadose dissolution is present. The Trogkofel Limestone is riddled by palaeokarstic dykes and caverns filled by (a) isopachous cement fringes up to a few decimetres thick, and/or (b) by red, geopetally-laminated lime mudstone to bio-lithoclastic wackestone; geopetal laminasets locally display convolute bedding. Small dissolution cavities are filled by grey internal sediment, or by crystal silt. Brecciated internal sediments overlain by unbrecciated, geopetally-laminated infillings record deformation during or after deposition of the Trogkofel Limestone. Polyphase fractures cemented by calcite may cross-cut both internal sediments and host rock. In the Trogkofel Limestone, local dolomitization is common. Replacement dolomites show a wide range of shapes and fabrics, including: (a) fine-crystalline anhedral xenotopic fabric, (b) coarse-crystalline subhedral to euhedral, hypidiotopic to idiotopic fabric of turbid or optically zoned crystals, and (c) saddle dolomite as replacement

  7. 78 FR 33467 - Second Allocation of Public Transportation Emergency Relief Funds in Response to Hurricane Sandy...

    Science.gov (United States)

    2013-06-04

    ... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Second Allocation of Public Transportation Emergency Relief Funds in Response to Hurricane Sandy: Response, Recovery & Resiliency; Correction... allocation of $3.7 billion under the Public Transportation Emergency Relief Program to the four FTA...

  8. 2014 U.S. Geological Survey CMGP LiDAR: Post Sandy (New Jersey)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — TASK NAME: USGS New Jersey CMGP Sandy Lidar 0.7 Meter NPS LIDAR lidar Data Acquisition and Processing Production Task USGS Contract No. G10PC00057 Task Order No....

  9. Amelioration of sandy soils in drought stricken areas through use of ...

    African Journals Online (AJOL)

    ACSS

    improving N, P, Ca and Mg content in sandy soils, and consequently support crop growth and yield. ... stress, soil moisture conservation, soil fertility management ... water many times its own weight. ... improves the productivity of degraded,.

  10. 2012 USGS EAARL-B Coastal Topography: Post-Sandy, First Surface (NJ)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — ASCII xyz and binary point-cloud data, as well as a digital elevation model (DEM) of a portion of the New Jersey coastline, pre- and post-Hurricane Sandy (October...

  11. Expanded uncertainty estimation methodology in determining the sandy soils filtration coefficient

    Science.gov (United States)

    Rusanova, A. D.; Malaja, L. D.; Ivanov, R. N.; Gruzin, A. V.; Shalaj, V. V.

    2018-04-01

    The combined standard uncertainty estimation methodology in determining the sandy soils filtration coefficient has been developed. The laboratory researches were carried out which resulted in filtration coefficient determination and combined uncertainty estimation obtaining.

  12. Will the future atmospheric circulation favor the landfall of Sandy-like superstorms? (Invited)

    Science.gov (United States)

    Barnes, E. A.; Polvani, L. M.; Sobel, A. H.

    2013-12-01

    Superstorm Sandy ravaged the Eastern seaboard of the United States, costing a great number of lives and billions of dollars in damage. Whether events like Sandy will become more frequent as anthropogenic greenhouse gases continue to increase remains an open and complex question. Here, we consider whether the persistent large-scale atmospheric patterns that steered Sandy onto the coast will become more frequent in the coming decades. Using the CMIP5 multi-model ensemble, we demonstrate that climate models consistently project a decrease in the frequency and persistence of the westward flow that led to Sandy's unprecedented track, implying that future atmospheric conditions are less likely than at present to propel storms westward into the coast.

  13. 2014 NOAA Ortho-rectified Mosaic of Hurricane Sandy Coastal Impact Area

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains ortho-rectified mosaic tiles at 0.35m GSD created for NOAA Integrated Ocean and Coastal Mapping (IOCM) initiative in Hurricane Sandy coastal...

  14. 2012-2013 Post-Hurricane Sandy EAARL-B Submerged Topography - Barnegat Bay, New Jersey

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Binary point-cloud data for part of Barnegat Bay, New Jersey, post-Hurricane Sandy (October 2012 hurricane), were produced from remotely sensed, geographically...

  15. Submarine terrace limestones from the continental slope off Saurashtra-Bombay: Evidence of Late Quaternary neotectonic activity

    Digital Repository Service at National Institute of Oceanography (India)

    Rao, V.P.; Veerayya, M.

    cements occur as isopachous crusts. Dissolution and clotting of aragonite needles and drusy calcite in the interstices indicate cementation of the limestones at inter-tidal conditions. The age of the limestones is 11,900 years BP. These imply that the 130...

  16. Lithofacies and petrophysical properties of Portland Base Bed and Portland Whit Bed limestone as related to durability

    NARCIS (Netherlands)

    Dubelaar, C.W.; Engering, S.; Hees, R.P.J. van; Koch, R.; Lorenz, H.G.

    2003-01-01

    This study focuses on the differences in lithofacies and petrophysical properties of Base Bed and Whit Bed Portland limestone and the presumed relationships between these characteristics and the durability of this building stone. As Portland limestone probably will be used as a stone for several

  17. Lithofacies and Petrophysical Properties of Portland Base Bed and Portland Whit Bed Limestone as Related to Durability

    NARCIS (Netherlands)

    Dubelaar, C.W.; Engering, S.; Van Hees, R.P.J.; Koch, R.; Lorenz, H.G.

    2003-01-01

    This study focuses on the differences in lithofacies and petrophysical properties of Base Bed and Whit Bed Portland limestone and the presumed relationships between these characteristics and the durability of this building stone. As Portland limestone probably will be used as a stone for several

  18. High-temperature CO2 capture cycles of hydrated limestone prepared with aluminum (hydr)oxides derived from kaolin

    International Nuclear Information System (INIS)

    Wang, Ke; Zhao, Pengfei; Guo, Xin; Han, Dongtai; Chao, Yang

    2014-01-01

    Highlights: • Hydrated limestone exhibited a higher reactivity and stability. • Microstructure of hydrated limestone was significantly improved. • Hydrated limestone still suffered less loss-incapacity. • Hydrated limestone sorbents with kaolin-based binders were prepared and characterized. • Sorbents prepared from hydrated limestone and Al(OH) 3 binder are a promising sorbent. - Abstract: A simple and convenient process was used to improve the utilization of natural limestone and kaolin for calcium looping technology and environmental applications. The calcined natural limestone modified with the distilled water (denoted as Limestone-W), was systematically studied and compared with the other CaO sorbents (calcium acetate, calcium D-gluconate and calcined natural limestone). These CaO-based sorbents were tested for their CO 2 capture behavior through 20 carbonation/calcination cycles in a thermo-gravimetric analyzer (TGA). Their morphology, pore structure and phase composition before and after carbonation/calcination cycles were determined by scanning electron microscopy, nitrogen adsorption, and X-ray diffraction. The first-cycle and multicycle sorption results revealed that the Limestone-W sorbent exhibited a relatively faster reaction rate and higher cyclic CO 2 capture. The characterization data indicated that the Limestone-W was composed of a special calcium oxide structure with lower crystalline and higher porosity nanoparticles, which appeared to be the main reasons for its higher CO 2 capture capability. However, the Limestone-W still suffered loss of reactivity, even though it was less pronounced than the other CaO sorbent. To avoid this unfavorable effect, a thermally stable inert material (aluminum hydroxide derived from kaolin) was incorporated into the Limestone-W structure. This new sorbent revealed higher stability because the formation of a stable framework of Ca 12 Al 14 O 33 particles hindered densification and sintering of the CaO phase

  19. Migration characteristics of cobalt-60 through sandy soil in high pH solution

    International Nuclear Information System (INIS)

    Ohnuki, Toshihiko

    1992-01-01

    Migration characteristics of 60 Co through sandy soil in high pH solution has been investigated by both column and batch techniques. The association of 60 Co with the sandy soil and its components were studied by sequential extraction techniques. The concentration profile of 60 Co in the sandy soil column was composed of two exponential curves showing that 60 Co would consist of immobile and mobile fractions. The immobile 60 Co was retained by the sandy soil and was distributed near the top. Though the mobile 60 Co was little sorbed by soil and migrated through the soil column, maximum concentration of 60 Co in the effluents decreased slightly with increasing path length of the soil column. The sequential extraction of 60 Co from the sandy soil and from its components showed that 60 Co was sorbed by both manganese oxide and clay minerals. And manganese oxide is one of the responsible soil components for the observed decrease in the maximum concentration of 60 Co in the effluents. Although the content of manganese oxide in the sandy soil was 0.13%, manganese oxide is the important component to prevent from the migration of 60 Co in the high pH solution. (author)

  20. EFFECTS OF ALKALINE SANDY LOAM ON SULFURIC SOIL ACIDITY AND SULFIDIC SOIL OXIDATION

    Directory of Open Access Journals (Sweden)

    Patrick S. Michael

    2015-08-01

    Full Text Available  In poor soils, addition of alkaline sandy loam containing an adequate proportion of sand, silt and clay would add value by improving the texture, structure and organic matter (OM for general use of the soils. In acid sulfate soils (ASS, addition of alkaline sandy would improve the texture and leach out salts as well as add a sufficient proportion of OM for vegetation establishment. In this study, addition of alkaline sandy loam into sulfuric soil effectively increased the pH, lowered the redox and reduced the sulfate content, the magnitude of the effects dependent on moisture content. Addition of alkaline sandy loam in combination with OM was highly effective than the effects of the lone alkaline sandy loam. When alkaline sandy was added alone or in combination with OM into sulfidic soil, the effects on pH and the redox were similar as in the sulfuric soil but the effect on sulfate content was variable. The effects under aerobic conditions were higher than under anaerobic conditions. The findings of this study have important implications for the general management of ASS where lime availability is a concern and its application is limited.International Journal of Environment Volume-4, Issue-3, June-August 2015Page: 42-54

  1. Rates of Hospitalization for Dehydration Following Hurricane Sandy in New Jersey.

    Science.gov (United States)

    Swerdel, Joel N; Rhoads, George G; Cosgrove, Nora M; Kostis, John B

    2016-04-01

    Hurricane Sandy, one of the most destructive natural disasters in New Jersey history, made landfall on October 29, 2012. Prolonged loss of electrical power and extensive infrastructure damage restricted access for many to food and water. We examined the rate of dehydration in New Jersey residents after Hurricane Sandy. We obtained data from 2008 to 2012 from the Myocardial Infarction Data Acquisition System (MIDAS), a repository of in-patient records from nonfederal New Jersey hospitals (N=517,355). Patients with dehydration had ICD-9-CM discharge diagnosis codes for dehydration, volume depletion, and/or hypovolemia. We used log-linear modeling to estimate the change in in-patient hospitalizations for dehydration comparing 2 weeks after Sandy with the same period in the previous 4 years (2008-2011). In-patient hospitalizations for dehydration were 66% higher after Sandy than in 2008-2011 (rate ratio [RR]: 1.66; 95% confidence interval [CI]: 1.50, 1.84). Hospitalizations for dehydration in patients over 65 years of age increased by nearly 80% after Sandy compared with 2008-2011 (RR: 1.79; 95% CI: 1.58, 2.02). Sandy was associated with a marked increase in hospitalizations for dehydration. Reducing the rate of dehydration following extreme weather events is an important public health concern that needs to be addressed, especially in those over 65 years of age.

  2. Investigation of superstorm Sandy 2012 in a multi-disciplinary approach

    Science.gov (United States)

    Kunz, M.; Mühr, B.; Kunz-Plapp, T.; Daniell, J. E.; Khazai, B.; Wenzel, F.; Vannieuwenhuyse, M.; Comes, T.; Elmer, F.; Schröter, K.; Fohringer, J.; Münzberg, T.; Lucas, C.; Zschau, J.

    2013-10-01

    At the end of October 2012, Hurricane Sandy moved from the Caribbean Sea into the Atlantic Ocean and entered the United States not far from New York. Along its track, Sandy caused more than 200 fatalities and severe losses in Jamaica, The Bahamas, Haiti, Cuba, and the US. This paper demonstrates the capability and potential for near-real-time analysis of catastrophes. It is shown that the impact of Sandy was driven by the superposition of different extremes (high wind speeds, storm surge, heavy precipitation) and by cascading effects. In particular the interaction between Sandy and an extra-tropical weather system created a huge storm that affected large areas in the US. It is examined how Sandy compares to historic hurricane events, both from a hydro-meteorological and impact perspective. The distribution of losses to different sectors of the economy is calculated with simple input-output models as well as government estimates. Direct economic losses are estimated about USD 4.2 billion in the Caribbean and between USD 78 and 97 billion in the US. Indirect economic losses from power outages is estimated in the order of USD 16.3 billion. Modelling sector-specific dependencies quantifies total business interruption losses between USD 10.8 and 15.5 billion. Thus, seven years after the record impact of Hurricane Katrina in 2005, Hurricane Sandy is the second costliest hurricane in the history of the United States.

  3. Investigation of superstorm Sandy 2012 in a multi-disciplinary approach

    Directory of Open Access Journals (Sweden)

    M. Kunz

    2013-10-01

    Full Text Available At the end of October 2012, Hurricane Sandy moved from the Caribbean Sea into the Atlantic Ocean and entered the United States not far from New York. Along its track, Sandy caused more than 200 fatalities and severe losses in Jamaica, The Bahamas, Haiti, Cuba, and the US. This paper demonstrates the capability and potential for near-real-time analysis of catastrophes. It is shown that the impact of Sandy was driven by the superposition of different extremes (high wind speeds, storm surge, heavy precipitation and by cascading effects. In particular the interaction between Sandy and an extra-tropical weather system created a huge storm that affected large areas in the US. It is examined how Sandy compares to historic hurricane events, both from a hydro-meteorological and impact perspective. The distribution of losses to different sectors of the economy is calculated with simple input-output models as well as government estimates. Direct economic losses are estimated about USD 4.2 billion in the Caribbean and between USD 78 and 97 billion in the US. Indirect economic losses from power outages is estimated in the order of USD 16.3 billion. Modelling sector-specific dependencies quantifies total business interruption losses between USD 10.8 and 15.5 billion. Thus, seven years after the record impact of Hurricane Katrina in 2005, Hurricane Sandy is the second costliest hurricane in the history of the United States.

  4. Effects of Pisha sandstone content on solute transport in a sandy soil.

    Science.gov (United States)

    Zhen, Qing; Zheng, Jiyong; He, Honghua; Han, Fengpeng; Zhang, Xingchang

    2016-02-01

    In sandy soil, water, nutrients and even pollutants are easily leaching to deeper layers. The objective of this study was to assess the effects of Pisha sandstone on soil solute transport in a sandy soil. The miscible displacement technique was used to obtain breakthrough curves (BTCs) of Br(-) as an inert non-adsorbed tracer and Na(+) as an adsorbed tracer. The incorporation of Pisha sandstone into sandy soil was able to prevent the early breakthrough of both tracers by decreasing the saturated hydraulic conductivity compared to the controlled sandy soil column, and the impeding effects increased with Pisha sandstone content. The BTCs of Br(-) were accurately described by both the convection-dispersion equation (CDE) and the two-region model (T-R), and the T-R model fitted the experimental data slightly better than the CDE. The two-site nonequilibrium model (T-S) accurately fit the Na(+) transport data. Pisha sandstone impeded the breakthrough of Na(+) not only by decreasing the saturated hydraulic conductivity but also by increasing the adsorption capacity of the soil. The measured CEC values of Pisha sandstone were up to 11 times larger than those of the sandy soil. The retardation factors (R) determined by the T-S model increased with increasing Pisha sandstone content, and the partition coefficient (K(d)) showed a similar trend to R. According to the results of this study, Pisha sandstone can successfully impede solute transport in a sandy soil column. Copyright © 2015 Elsevier Ltd. All rights reserved.

  5. Hurricane Sandy (New Jersey): Mortality Rates in the Following Month and Quarter.

    Science.gov (United States)

    Kim, Soyeon; Kulkarni, Prathit A; Rajan, Mangala; Thomas, Pauline; Tsai, Stella; Tan, Christina; Davidow, Amy

    2017-08-01

    To describe changes in mortality after Hurricane Sandy made landfall in New Jersey on October 29, 2012. We used electronic death records to describe changes in all-cause and cause-specific mortality overall, in persons aged 76 years or older, and by 3 Sandy impact levels for the month and quarter following Hurricane Sandy compared with the same periods in earlier years adjusted for trends. All-cause mortality increased 6% (95% confidence interval [CI] = 2%, 11%) for the month, 5%, 8%, and 12% by increasing Sandy impact level; and 7% (95% CI = 5%, 10%) for the quarter, 5%, 8%, and 15% by increasing Sandy impact level. In elderly persons, all-cause mortality rates increased 10% (95% CI = 5%, 15%) and 13% (95% CI = 10%, 16%) in the month and quarter, respectively. Deaths that were cardiovascular disease-related increased by 6% in both periods, noninfectious respiratory disease-related by 24% in the quarter, infection-related by 20% in the quarter, and unintentional injury-related by 23% in the month. Mortality increased, heterogeneous by cause, for both periods after Hurricane Sandy, particularly in communities more severely affected and in the elderly, who may benefit from supportive services.

  6. Lightweight concrete with Algerian limestone dust. Part II: study on 50% and 100% replacement to normal aggregate at timely age

    Directory of Open Access Journals (Sweden)

    S. Kitouni

    2015-12-01

    Full Text Available Abstract A control lightweight concrete (LWC mixture made with 50% and 100% of limestone as a replacement of coarse aggregates in weight was prepared. Limestone is used for economical and environmental concern. The concrete samples were cured at 65% relative humidity at 20 ºC. The compressive and flexural tensile strengths, elastic modulus and Poisson's ratio of hardened concrete were measured. Laboratory compressive and tensile strength tests results showed that LWC can be produced by the use of limestone. The aim of this study is twofold: one is to design a lightweight concrete with the use of limestone that will provide an advantage of reduction in dead weight of a structure; and second is to obtain a more economical LWC mixture with the use of limestone.

  7. Influence of limestone fillers on combustion characteristics of asphalt mortar for pavements

    DEFF Research Database (Denmark)

    Ke, Wu; Kai, Zhu; Wu, Hao

    2014-01-01

    Asphalt materials will be ignited and release significant toxic fumes within tunnel fires. Thus, combustion characteristics of asphalt materials used in road tunnel should be studied in order to limit such an adverse effect. In the present work we study the influence of limestone fillers on combu...

  8. Model of fragmentation of limestone particles during thermal shock and calcination in fluidised beds

    Energy Technology Data Exchange (ETDEWEB)

    Saastamoinen, J.; Pikkarainen, T.; Tourunen, A.; Rasanen, M.; Jantti, T. [VTT Technical Research Center, Jyvaskyla (Finland)

    2008-11-15

    Fragmentation of limestone due to thermal shock and calcination in a fluidised bed was studied through experiments and modelling. The time for heating was estimated by model calculations and the time for calcination by measurements. Fragmentation due to thermal shock was carried out by experiments in a CO{sub 2} atmosphere in order to prevent the effect of calcination. It was found to be much less than fragmentation due to calcination. Average particle sizes before and after fragmentation are presented for several types of limestone. The effects of particle size and gas composition on the primary fragmentation were studied through experiments. Increasing the fluidisation velocity increased the tendency to fragment. The evolution of the particle size distribution (PSD) of limestone particles due to thermal shock and during calcination (or simultaneous calcination and sulphation) were calculated using a population balance model. Fragmentation due to thermal shock is treated as an instantaneous process. The fragmentation frequency during calcination is presented as exponentially decaying over time. In addition to the final PSD, this model also predicts the PSD during the calcination process. The fragmentation was practically found to end after 10 min. Furthermore. a population balance method to calculate the particle size distribution and amount of limestone in fluidised beds in dynamic and steady state, when feeding history is known, is presented.

  9. Limestone particle attrition and size distribution in a small circulating fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Zhongxiang Chen; John R. Grace; C. Jim Lim [University of British Columbia, Vancouver, BC (Canada). Department of Chemical and Biological Engineering

    2008-06-15

    Limestone particle attrition was investigated in a small circulating fluidized bed reactor at temperatures from 25 to 850{sup o}C, 1 atm pressure and superficial gas velocities from 4.8 to 6.2 m/s. The effects of operating time, superficial gas velocity and temperature were studied with fresh limestone. No calcination or sulfation occurred at temperatures {le} 580{sup o}C, whereas calcination and sulfation affected attrition at 850{sup o}C. Increasing the temperature (while maintaining the same superficial gas velocity) reduced attrition if there was negligible calcination. Attrition was high initially, but after about 24 h, the rate of mass change became constant. The ratio of initial mean particle diameter to that at later times increased linearly with time and with (U{sub g} - U{sub mf}){sup 2}, while decreasing exponentially with temperature, with an activation energy for fresh limestone of -4.3 kJ/mol. The attrition followed Rittinger's surface theory. The change of surface area of limestone particles was proportional to the total excess kinetic energy consumed and to the total attrition time, whereas the change of surface area decreased exponentially with increasing temperature. At 850{sup o}C, the attrition rate of calcined lime was highest, whereas the attrition rate was lowest for sulfated particles. When online impact attrition was introduced, the attrition rate was about an order of magnitude higher than without impacts. 25 refs., 14 figs., 4 tabs.

  10. Performance Monitoring: Evaluating an Organic Carbon-Limestone PRB for Treatment of Heavy Metals and Acidity

    Science.gov (United States)

    Since 2004, researchers from the U.S. EPA National Risk Management Research Laboratory (NRMRL) have annually evaluated performance of an organic carbon-limestone permeable reactive barrier (PRB) system installed in 2003 by EPA Region 6 at the Delatte Metals Superfund site in Ponc...

  11. Attrition of limestones by impact loading in fluidized beds: The influence of reaction conditions

    Energy Technology Data Exchange (ETDEWEB)

    Scala, Fabrizio [Istituto di Ricerche sulla Combustione, Consiglio Nazionale delle Ricerche, Napoli (Italy); Salatino, Piero [Istituto di Ricerche sulla Combustione, Consiglio Nazionale delle Ricerche, Napoli (Italy); Dipartimento di Ingegneria Chimica, Universita degli Studi di Napoli Federico II, Napoli (Italy)

    2010-09-15

    The extent of attrition associated with impact loading was studied for five different limestones pre-processed in fluidized bed under different reaction conditions. The experimental procedure was based on the measurement of the amount and the particle size distribution of the debris generated upon impact of sorbent samples against a target at velocities between 10 and 45 m/s. The effect of calcination, sulfation and calcination/re-carbonation on impact damage was assessed. Fragmentation by impact loading of the limestones was significant and increased with the impact velocity. Lime samples displayed the largest propensity to undergo impact damage, followed by sulfated, re-carbonated and raw limestones. Fragmentation of the sulfated samples followed a pattern typical of the failure of brittle materials. On the other hand, the behaviour of lime samples better conformed to a disintegration failure mode, with extensive generation of very fine fragments. Raw limestone and re-carbonated lime samples followed either of the two patterns depending on the sorbent nature. The extent of particle fragmentation increased after multiple impacts, but the incremental amount of fragments generated upon one impact decreased with the number of successive impacts. (author)

  12. Optimization of nanolime solvent for the consolidation of coarse porous limestone

    Science.gov (United States)

    Borsoi, Giovanni; Lubelli, Barbara; van Hees, Rob; Veiga, Rosário; Silva, António Santos

    2016-09-01

    The potentialities of nanomaterials for application in the field of conservation have been widely investigated in the last two decades. Among nanomaterials, nanolimes, i.e., dispersions of lime nanoparticles in alcohols are promising consolidating products for calcareous materials. Nanolimes are effective in recovering the very superficial loss of cohesion of decayed materials, but they do not always provide sufficient mass consolidation. This limitation is mainly related to the deposition of the nanoparticles nearby the surface of the material. Experimental research has been set up with the aim of improving the in-depth deposition of lime nanoparticles. Previous research by the authors has shown that nanolime deposition within a substrate can be controlled by adapting the nanolimes properties (kinetic stability and evaporation rate) to the moisture transport behavior of the substrate. Nanolime properties can be modified by the use of different solvents. In this research, nanolime dispersions have been further optimized for application on Maastricht limestone, a coarse porous limestone. Firstly, nanolimes were synthesized and dispersed in ethanol and/or water, both pure and mixed in different percentages. Subsequently, based on the kinetic stability of the nanolime dispersions, the most promising solvent mixtures were selected and applied on the limestone. The deposition of lime nanoparticles within the limestone was studied by phenolphthalein test, optical microscopy and scanning electron microscopy. The results confirm that nanolime dispersed in a mixture of ethanol (95 %) and water (5 %) can guarantee a better nanoparticles in-depth deposition within coarse porous substrates, when compared to dispersions in pure ethanol.

  13. Use of limestone obtained from waste of the mussel cannery industry for the production of mortars

    International Nuclear Information System (INIS)

    Ballester, Paloma; Marmol, Isabel; Morales, Julian; Sanchez, Luis

    2007-01-01

    Various types of cement-SiO 2 -CaCO 3 mortar were prepared by replacing quarry limestone aggregate with limestone obtained as a by-product from waste of the mussel cannery industry. The CaCO 3 aggregate consists mainly of elongated prismatic particles less than 4 μm long rather than of the rounded particles of smaller size (2-6 μm) obtained with quarry limestone. The mechanical and structural properties of the mortars were found to be influenced by aggregate morphology. Setting of the different types of mortar after variable curing times was evaluated by scanning electron microscopy (SEM), thermogravimetric analysis (TG) and mercury intrusion porosimetry (MIP) techniques. Mortars with a high content in mussel shell limestone exhibited a more packed microstructure, which facilitates setting of cement and results in improved mortar strength. The enhanced mechanical properties of the new mortars allow the cement content in the final mortar composition to be decreased and production costs to be reduced as a result

  14. Conceptualization of flow and transport in a limestone aquifer by multiple dedicated hydraulic and tracer tests

    DEFF Research Database (Denmark)

    Mosthaf, Klaus; Brauns, Bentje; Fjordbøge, Annika Sidelmann

    2018-01-01

    Limestone aquifers are of great interest as a drinking water resource in many countries. They often have a complex crushed and fractured geology, which makes the analysis and description of flow and transport processes in such aquifers a challenging task. In this study, the solute transport behav...

  15. Lateral capacity of rock sockets in limestone under cyclic and repeated loading.

    Science.gov (United States)

    2010-08-01

    This report contains the results from full scale lateral load testing of two short rock socketed shafts in : limestone, and the development of recommendations for p-y analysis using those results. Two short shafts 42 : inches in diameter were constru...

  16. Effects of limestone petrography and calcite microstructure on OPC clinker raw meals burnability

    Science.gov (United States)

    Galimberti, Matteo; Marinoni, Nicoletta; Della Porta, Giovanna; Marchi, Maurizio; Dapiaggi, Monica

    2017-10-01

    Limestone represents the main raw material for ordinary Portland cement clinker production. In this study eight natural limestones from different geological environments were chosen to prepare raw meals for clinker manufacturing, aiming to define a parameter controlling the burnability. First, limestones were characterized by X-Ray Fluorescence, X-Ray Powder Diffraction and Optical Microscopy to assess their suitability for clinker production and their petrographic features. The average domains size and the microstrain of calcite were also determined by X-Ray Powder Diffraction line profile analysis. Then, each limestone was admixed with clay minerals to achieve the adequate chemical composition for clinker production. Raw meals were thermally threated at seven different temperatures, from 1000 to 1450 °C, to evaluate their behaviour on heating by ex situ X-Ray Powder Diffraction and to observe the final clinker morphology by Scanning Electron Microscopy. Results indicate the calcite microstrain is a reliable parameter to predict the burnability of the raw meals, in terms of calcium silicates growth and lime consumption. In particular, mixtures prepared starting from high-strained calcite exhibit a better burnability. Later, when the melt appears this correlation vanishes; however differences in the early burnability still reflect on the final clinker composition and texture.

  17. An experimental study on the primary fragmentation and attrition of limestones in a fluidized bed

    International Nuclear Information System (INIS)

    Yao, Xuan; Zhang, Hai; Yang, Hairui; Liu, Qing; Wang, Jinwei; Yue, Guangxi

    2010-01-01

    In this paper, an experimental study on the primary fragmentation and attrition of 5 limestones in a fluidized bed was conducted. The intensity of fragmentation and attrition were measured in the same apparatus but at different fluidizing velocities. It was found that the averaged size of the particles decreased by about 10-20% during the fragmentation process. The important factors for particle comminution include limestone types, heating rate, calcination condition and ambient CO 2 concentration. Fragmentation mainly occurred in the first a few minutes in the fluidized bed and it was more intense than that in the muffle furnace at the same temperature. The original size effect was ambiguous, depending on the limestone type. The comminution caused by attrition mainly occurred during calcination process rather than sulphation process. The sulphation process was fragmentation and attrition resisted. The attrition rate of sulphate was similar to that of lime in trend, decaying exponentially with time, but was one-magnitude-order smaller than that of lime. Present experimental results indicate that fragmentation mechanism of the limestone is dominated by CO 2 release instead of thermal stress. (author)

  18. Piedramuelle Limestone in the building heritage of Oviedo, Spain, and adjacent towns.

    Science.gov (United States)

    Cardenes Van den Eynde, Victor; Mateos, Felix Javier; Valdeon, Luis; Rojo, Araceli

    2017-04-01

    The Piedramuelle limestone has a very important representation in the building heritage of Oviedo, historical capital of Asturias (Spain) and surrounding towns. This argillaceous limestone has been quarried since the High Middle Ages until the beginning of the XX century. The main mineralogical components are carbonates (mainly calcite and sometimes ankerite, 70-90%), quartz (5-15%), terrigenous minerals (6-15%) and iron oxides (blocks and ashlars of the buildings. Some of the buildings constructed with Piedramuelle limestone are the Cathedral, the Old University and the Palaces from the XVII and XVIII centuries. The ambiance and historical architecture of Oviedo and adjacent towns is closely linked with the textures and colors of this stone. Nowadays, the Piedramuelle limestone is not exploited anymore, being the quarries exhausted. This represents an issue from a conservation point of view, since there is not a suitable stone for replacement. In order to preserve and maintain the building heritage of these towns, it is very important to prospect and protect the remaining outcrops still able to supply this characteristic stone.

  19. Effects of phosphate limestone on structure and quality under sugarcane vertisoles

    Directory of Open Access Journals (Sweden)

    Pedro Cairo Cairo

    2017-10-01

    Full Text Available The work was developed in sugarcane areas of cuban vertisols of the north coast of the province of Villa Clara municipality of Sagua la Grande, with the aim of evaluating the effectiveness of phosphate limestone and their combinations with fertilizers and organic manure on the structure and quality of vertisols under sugarcane cultivation. An experiment with phosphate limestone levels and combinations with organic manure (compost, filter cake and fertilizers (NPK was carried out on a wasstrip-block design. A soil analysis was performedat the depth of 0-20 and 20 -40 cm 36 months after the application of treatments. Organic matter, stable aggregates, factor structure, permeability, T value, exchangeable cations, index soil quality and productivity of sugarcane were evaluated. Phosphate limestone and there combinations with organic manures manifested significant effects on soil structure both in the surface layer and subsurface with residual impact over time to 36 months. The results show the close relationship between phosphate limestone and there combinations with organic manures on soil quality index additive, yield of sugarcane and economic impact.

  20. Thermal effects induced by laser ablation in non-homogeneous limestone covered by an impurity layer

    Science.gov (United States)

    Cocean, Alexandru; Pelin, Vasile; Cazacu, Marius Mihai; Cocean, Iuliana; Sandu, Ion; Gurlui, Silviu; Iacomi, Felicia

    2017-12-01

    This paper reports preliminary results concerning thermal effects induced by urban/industrial air pollutants deposited on a limestone rock when heated by pulsed laser in the cleaning process. The process of laser cleaning treatment of the crust is simulated using COMSOL Multiphysics 4.4, finite element analysis software. Scanning Electron Microscopy coupled with Energy Dispersive X-ray Spectroscopy and Laser Induced Breakdown Spectroscopy techniques have been used to analyze the chemical composition of the samples. Two elements found as being present into the dust and in the crust, such as iron and magnesium particles are used for simulation in COMSOL. Therefore, the profiles heat evolutions on the crust surface and inside limestone are obtained as thermal interactions between the three components (iron, magnesium and limestone), simulating the non-homogeneous materials. It has been observed that iron impurities caused by the dust deposition may damage the limestone through a process of overheating, as a consequence of a high thermal conduction phenomenon, recorded for the region with iron impurities and sizes of micrometric order are localized. The thermal contact between the three components results in plots that reflect their thermal interactions.

  1. Radiological significance of Egyptian limestone and alabaster used for construction of dwellings

    International Nuclear Information System (INIS)

    El-Taher, A.; Makhluf, V.

    2011-01-01

    The natural radionuclides in limestone and alabaster found in Assuit Governorate in Upper Egypt have been investigated by passive gamma-ray spectrometry. From the measured γ-ray spectra, specific activities were determined. The measured activity concentrations for these natural radionuclides were compared with the reported data from other countries. The radiation hazard parameters related to the exposure of limestone and alabaster have also been calculated. The obtained results of radium equivalent Raeq, level index Iγr, the external hazard index H ex and absorbed dose rate in limestone (90.44, 0.63, 0.17, 39.94) and (70.86, 0.50, 0.13, 31.55) are lower than the acceptable level 370 Bqkg -1 for radium equivalent Ra eq , 1 for level index Iγr, the external hazard index H e≤ I and 59 (nGy.h -1 ) for absorbed dose rate. So limestone and alabaster can be used as building construction without exceeding the proposed radioactivity criterion level. (author)

  2. 230Th/234U dating of coral limestones and vertical uplift at Djibouti

    International Nuclear Information System (INIS)

    Faure, Hugues; Hoang, C.T.; Lalou, Claude

    1980-01-01

    Coral limestones sampled from marine terraces along the Afar coast have been dated by the 230 Th/ 234 U method. The ages confirm the stratigraphic unity of these formations and the existence of the paleo sea level dated 124 000 years ago in this region. These results permit to deduce the uplift rates of this littoral [fr

  3. Treatment Of Metal-Mine Effluents By Limestone Neutralization And Calcite Co-Precipitation

    Science.gov (United States)

    The U.S. Geological Survey - Leetown Science Center and the Colorado School of Mines have developed a remediation process for the treatment of metals in circumneutral mining influenced waters. The process involves treatment with a pulsed limestone bed (PLB) system, followed by c...

  4. Treatment Of Metal-Mine Effluents By Limestone Neutralization And Calcite Co-Precipitation (Presentation)

    Science.gov (United States)

    The U.S. Geological Survey - Leetown Science Center and the Colorado School of Mines have developed a remediation process for the treatment of metals in circumneutral mining influenced waters. The process involves treatment with a pulsed limestone bed (PLB) system, followed by c...

  5. Limestone amendments and the establishment of legumes on pyritic colliery spoil

    Energy Technology Data Exchange (ETDEWEB)

    Jefferies, R A

    1981-11-01

    This paper examines the effect of high liming, using two commercially available limestone grades of different particle size distributions, on the establishment of six contrasting legume species, in order to determine whether other legume species are more tolerant of the conditions imposed by high liming, and whether the effect can be avoided. 13 refs.

  6. Autogenous and drying shrinkage of sodium carbonate activated slag altered by limestone powder incorporation

    NARCIS (Netherlands)

    Yuan, B.; Yu, Q.L.; Dainese, E.; Brouwers, H.J.H.

    2017-01-01

    This paper aims to study the shrinkage mechanism of sodium carbonate activated slag containing limestone powder (LP). The workability, pore structure, reaction kinetics and strength development were characterized. The results show that the autogenous shrinkage increases when the dosage of LP is low

  7. Assessing the chemical involvement of limestone powder in sodium carbonate activated slag

    NARCIS (Netherlands)

    Yuan, B.; Yu, Q.; Brouwers, H.J.H.

    2017-01-01

    This study aims to investigate the effect of limestone powder (LP) on the reaction of sodium carbonate activated slag. The results show that the incorporated LP up to 30% improves the strength development, especially at advanced curing ages. A slightly accelerated reaction is observed for samples

  8. Influence of limestone powder on the reaction kinetics and mechanical properties of sodium carbonate activated slag

    NARCIS (Netherlands)

    Yuan, B.; Yu, Q.; Brouwers, H.J.H.

    2016-01-01

    The effects of limestone powder (LP) on the performance of Portland cement based composites have been extensively studied, considering that LP not only acts as nuclei sites, but that it is also chemically involved in the hydration process, which improves the reaction degree at the early age. In high

  9. Transient Catalytic Activity of Calcined Dolomitic Limestone in a Fluidized Bed during Gasification of Woody Biomass.

    Czech Academy of Sciences Publication Activity Database

    Pohořelý, Michael; Jeremiáš, Michal; Skoblia, S.; Beňo, Z.; Šyc, Michal; Svoboda, Karel

    2016-01-01

    Roč. 30, č. 5 (2016), s. 4065-4071 ISSN 0887-0624 R&D Projects: GA ČR GC14-09692J Institutional support: RVO:67985858 Keywords : fluidized- bed gasification * woody biomass * limestone Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 3.091, year: 2016

  10. Hydrobiogeochemical interactions in 'anoxic' limestone drains for neutralization of acidic mine drainage

    Science.gov (United States)

    Robbins, E.I.; Cravotta, C.A.; Savela, C.E.; Nord, G.L.

    1999-01-01

    Processes affecting neutralization of acidic coal mine drainage were evaluated within 'anoxic' limestone drains (ALDs). Influents had pH???3.5 and dissolved oxygen treatment step is indicated to promote Al removal before diverting acidic mine water into alkalinity-producing materials. ?? 1998 Elsevier Science Ltd.

  11. Extensive yellow crusts below limestone overhangs: a new taxon close to a minute epiphytic lichen

    Czech Academy of Sciences Publication Activity Database

    Vondrák, Jan; Moniri, M. H.; Malíček, Jiří; Košnar, J.

    2017-01-01

    Roč. 35, č. 3 (2017), s. 368-376 ISSN 0107-055X Institutional support: RVO:67985939 Keywords : Caloplaca substerilis * limestone rocks * Central Europe Subject RIV: EF - Botanics OBOR OECD: Plant sciences, botany Impact factor: 0.847, year: 2016

  12. Effect of Limestone Powder on Acid Attack Characteristics of Cement Pastes

    Directory of Open Access Journals (Sweden)

    Shuhua LIU

    2014-12-01

    Full Text Available The acid resistance of cement pastes containing limestone powder with two different water-binder (w/b ratios exposed to acetic (pH = 4 and sulfuric acid (pH = 2 solutions respectively were investigated in this paper. Limestone powder, fly ash and silica fume were also added to the cement paste mixture at different proportions. Static and flowing aqueous environments were set in this experiment. Strength and microstructure of the pastes after acid attack were investigated by using strength test, X-ray diffractometer (XRD and scanning electron microscopy (SEM. The experimental results show that the erosion degree depends not only on pH value of the solution and w/b ratio of the pastes, but also on the content of limestone powder. Acetic acid reacts with calcium hydroxide and carbonate thus dissolving the pastes, while sulfuric acid consumed calcium hydroxide, and generated gypsum and ettringite. The consumption of calcium hydroxide in the flowing solution group is higher than that in the static solution because the flowing sulfuric acid solution has negative effect upon the gypsum crystallization. Fly ash and silica fume are beneficial to limestone cement paste because of the less calcium hydroxide formation, which is among the hydrates vulnerable to acid erosion. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6231

  13. Limestone and Zeolite as Alternative Media in Horizontal Subsurface Flow Constructed Wetlands: Laboratory-Scale Studies

    Science.gov (United States)

    Lizama, K.; Jaque, I.; Ayala, J.

    2016-12-01

    Arsenic is well known for its chronic toxicity. Millions of people around the world are currently at risk, drinking water with As concentrations above 10 ppb, the WHO drinking water guideline. Although different treatment options exist, they are often limited by elevated costs and maintenance requirements. Constructed wetlands are a natural water treatment system, capable to remove metals and metalloids -including As- via different physical, chemical and biological processes. The use of alternative supporting media to enhance As removal in subsurface flow wetlands has been recommended, but not sufficiently studied. Limestone and zeolite have been identified as effective supporting media in subsurface flow wetlands aiming As removal. However, there are still key aspects to be addressed, such as the implications of using these media, the speciation in the solid phase, the role of vegetation, etc. This study investigated the performance of limestone and zeolite in three types of experiments: batch, column and as main supporting media in a bench scale horizontal subsurface flow wetland system. Synthetic water resembling a contaminated river in Chile (As concentration=3 mg/L, Fe concentration= 100 mg/L, pH=2) was used in all experiments. In the batch experiments, the As concentration, the mass of media and the contact time were varied. The column system consisted of three limestone columns and three zeolite columns, operated under a hydraulic loading of 20 mm/d. The wetland system consisted of twelve PVC cells: six filled with zeolite and six with limestone. Phragmites australis were planted in three cells of each media type, as control cells. From the batch experiments, maximum As sorption capacities as indicated by Langmuir model were 1.3 mg/g for limestone and 0.17 mg/g for zeolite, at 18 h contact time and 6.3 g/L medium concentration. EDS and XPS analyses revealed that As and Fe were retained in zeolite at the end of the batch experiments. Zeolite and limestone

  14. The Öland limestone - A Swedish stone used for more than one thousand years

    Science.gov (United States)

    Schouenborg, Björn; Wickström, Linda; Mikaelsson, Jan

    2016-04-01

    The second largest island in Sweden is the home of the "Öland limestone", a condensed and bedded limestone whose origin dates back to Lower Ordovician, i.e. about 480 M years ago. Öland is a part of the palaeocontinent Baltica that, at the time, was situated at low latitudes with deposition of the calcareous sediments in a cool water environment. The limestone on Öland represents a proximal ramp tectonic setting, with the oldest sediments deposited in the west and younger sediments deposited towards east and southeast. Fluctuating sea-levels have created erosional hard grounds such as the Flowery sheet. These hardgrounds are recognised by their vivid colours and trace fossils, and can be traced all over Baltica, but is maybe best represented on Öland. Ordovician limestones are present in many places in Sweden, but it is the occurrence on Öland that is the most renowned in a building stone perspective. One reason for this is the favourable trading location, an island off the Swedish East coast in middle of the trading routes between the Baltic countries and the continent. Other reasons are the pleasant aesthetical values with numerous orthoceratites and other fossils. The limestones on Öland differ in colour. From the red varieties (with oxidized iron) to brownish and grey. The bedding is mostly in the cm-scale which easily enables very exploitable thickness of slabs. Every mm limestone represents about 1000 years of deposition. The limestone has most likely been used in a very crude way for many thousand years, but archaeological evidence of a more industrialized usage is just a little more than 1000 years. It is known from the literature that the first official Swedish king, Gustav Vasa (16th century), desired this stone. At the time it was called "Öland marble", and the king "imported" specialists to process it further at the Royal Stone workshop on northern Öland. Remnants of tools and working sites still remain in an outdoor museum. Export of the

  15. Morphological Changes of Limestone Sorbent Particles during Carbonation/Calcination Looping Cycles in a Thermogravimetric Analyzer (TGA) and Reactivation with Steam

    KAUST Repository

    Wu, Y.; Blamey, J.; Anthony, E. J.; Fennell, P. S.

    2010-01-01

    Carbonation and calcination looping cycles were carried out on four limestones in a thermogravimetric analyzer (TGA). The CO2 carrying capacity of a limestone particle decays very quickly in the first 10 cycles, reducing to about 20% of its original

  16. Water management in sandy soil using neutron scattering method

    International Nuclear Information System (INIS)

    Mohamed, K.M.

    2011-01-01

    This study was carried out during 2008/2009 at the Experimental Field of Soil and Water Research Department, Nuclear Research Center, Atomic Energy Authority, Inshas in a newly reclaimed sandy soil. The aims of this work are,- determine soil moisture tension within the active root zone and - detecting the behavior of soil moisture within the active root zoon by defines the total hydraulic potential within the soil profile to predict both of actual evapotranspiration and rate of moisture depletion This work also is aimed to study soil water distribution under drip irrigation system.- reducing water deep percolation under the active root depth.This study included two factors, the first one is the irrigation intervals, and the second one is the application rate of organic manure. Irrigation intervals were 5, 10 and 15 days, besides three application rates of organic manure (0 m 3 /fed, 20 m 3 /fed. and 30 m 3 /fed.) in -three replicates under drip irrigation system, Onion was used as an indicator plant. Obtained data show, generally, that neutron scattering technique and soil moisture retention curve model helps more to study the water behavior in the soil profile.Application of organic manure and irrigation to field capacity is a good way to minimize evapotranspiration and deep percolation, which was zero mm/day in the treated treatments.The best irrigation interval for onion plant, in the studied soil, was 5 days with 30m 3 /fad. an application rate of organic manure.Parameter α of van Genuchent's 1980 model was affected by the additions of organic manure, which was decreased by addition of organic manure decreased it. Data also showed that n parameter was decreased by addition of organic manure Using surfer program is a good tool to describe the water distribution in two directions (vertical and horizontal) through soil profile.

  17. Comparison of Limestone and Ground Fish for Treatment of Nutritional Rickets in Children in Nigeria.

    Science.gov (United States)

    Thacher, Tom D; Bommersbach, Tanner J; Pettifor, John M; Isichei, Christian O; Fischer, Philip R

    2015-07-01

    To determine whether children with calcium-deficiency rickets respond better to treatment with calcium as limestone or as ground fish. Nigerian children with active rickets (n = 96) were randomized to receive calcium as powdered limestone (920 mg of elemental calcium) or ground fish (952 mg of elemental calcium) daily for 24 weeks. Radiographic healing was defined as achieving a score of 1.5 or less on a 10-point scale. The median (range) age of enrolled children was 35 (6-151) months. Of the 88 children who completed the study, 29 (66%) in the ground fish group and 24 (55%) in the limestone group achieved the primary outcome of a radiographic score of 1.5 or less within 6 months (P = .39). The mean radiographic score improved from 6.2 ± 2.4 to 1.8 ± 2.2 in the ground fish group and from 6.3 ± 2.2 to 2.1 ± 2.4 in the limestone group (P = .68 for group comparison). In an intention to treat analysis adjusted for baseline radiographic score, age, milk calcium intake, and serum 25-hydroxyvitamin D concentration, the response to treatment did not differ between the 2 groups (P = .39). Younger age was associated with more complete radiographic healing in the adjusted model (aOR 0.74 [95% CI 0.57-0.92]). After 24 weeks of treatment, serum alkaline phosphatase had decreased, calcium and 25-hydroxyvitamin D increased, and bone mineral density increased in both groups, without significant differences between treatment groups. In children with calcium-deficiency rickets, treatment with calcium as either ground fish or limestone for 6 months healed rickets in the majority of children. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  18. Evaluation of Different Modeling Approaches to Simulate Contaminant Transport in a Fractured Limestone Aquifer

    Science.gov (United States)

    Mosthaf, K.; Rosenberg, L.; Balbarini, N.; Broholm, M. M.; Bjerg, P. L.; Binning, P. J.

    2014-12-01

    It is important to understand the fate and transport of contaminants in limestone aquifers because they are a major drinking water resource. This is challenging because they are highly heterogeneous; with micro-porous grains, flint inclusions, and being heavily fractured. Several modeling approaches have been developed to describe contaminant transport in fractured media, such as the discrete fracture (with various fracture geometries), equivalent porous media (with and without anisotropy), and dual porosity models. However, these modeling concepts are not well tested for limestone geologies. Given available field data and model purpose, this paper therefore aims to develop, examine and compare modeling approaches for transport of contaminants in fractured limestone aquifers. The model comparison was conducted for a contaminated site in Denmark, where a plume of a dissolved contaminant (PCE) has migrated through a fractured limestone aquifer. Multilevel monitoring wells have been installed at the site and available data includes information on spill history, extent of contamination, geology and hydrogeology. To describe the geology and fracture network, data from borehole logs was combined with an analysis of heterogeneities and fractures from a nearby excavation (analog site). Methods for translating the geological information and fracture mapping into each of the model concepts were examined. Each model was compared with available field data, considering both model fit and measures of model suitability. An analysis of model parameter identifiability and sensitivity is presented. Results show that there is considerable difference between modeling approaches, and that it is important to identify the right one for the actual scale and model purpose. A challenge in the use of field data is the determination of relevant hydraulic properties and interpretation of aqueous and solid phase contaminant concentration sampling data. Traditional water sampling has a bias

  19. Role of phytohormones in organogenic ability of elm multiplicated shoots

    Czech Academy of Sciences Publication Activity Database

    Malá, J.; Gaudinová, Alena; Dobrev, Petre; Eder, Josef; Cvikrová, Milena

    2006-01-01

    Roč. 50, č. 1 (2006), s. 8-14 ISSN 0006-3134 Institutional research plan: CEZ:AV0Z5038910; CEZ:AV0Z50380511 Keywords : auxin * cytokinins * multiplication of elm Subject RIV: GK - Forestry Impact factor: 1.198, year: 2006

  20. Rare earth element and strontium isotopic study of seamount-type limestones in Mesozoic accretionary complex of Southern Chichibu Terrane, central Japan. Implication for incorporation process of seawater REE into limestones

    International Nuclear Information System (INIS)

    Tanaka, Kazuya; Miura, Noriko; Asahara, Yoshihiro; Kawabe, Iwao

    2003-01-01

    Ishimaki and Tahara limestones occur as exotic blocks juxtaposed in the Mesozoic (Jurassic) accretionary complex of Southern Chichibu Terrane in eastern Aichi Prefecture, central Japan. They are supposed to be of the seamount-type limestone, since they have no terrigenous materials and are intimately associated with greenstones. REE (rare earth elements) and Sr isotopic studies for the limestones have been made in order to know their geochemical characteristics, ages and origins. Their 87 Sr/ 86 Sr ratios, when referred to the seawater 87 Sr/ 86 Sr curve and relevant geological data, suggest that Ishimaki and Tahara limestones are the late Permian and the Carboniferous to the Early Permian, respectively. Two greenstone fragments found inside the Ishimaki limestone block and one greenstone sample associated with Tahara limestone block, resemble the Hawaiian alkali basalt in the their REE and Y patterns. This is supporting the idea that the limestone blocks may be parts of reef limestones on ancient volcanic seamounts. All the limestone samples, except three unusual Tahara ones, show seawater REE and Y signatures in their chondrite-normalized patterns. Their REE/Ca ratios, however, are 10 2 -10 4 times as high as those ratios of modern biogenic carbonates like corals and the seawater. Accordingly, seawater REE and Y were incorporated into the limestones, when originally biogenic carbonates transformed into inorganic calcite and its secondary growths occurred in diagenesis in contact with sufficient seawater. This view is favored by the reported REE partition experiment between calcite overgrowths and seawater solution. The seawater Ce anomaly as a function of water depth in the modern ocean is a key to infer the water depth of the REE and Y incorporation. The Ce anomalies given by log (Ce/Ce*) for about a half of Ishimaki samples and most of Tahara ones are between -0.5 and -0.2, which are compatible with the shallow water origin. Another half of Ishimaki samples

  1. Groundwater monitoring of an open-pit limestone quarry: groundwater characteristics, evolution and their connections to rock slopes.

    Science.gov (United States)

    Eang, Khy Eam; Igarashi, Toshifumi; Fujinaga, Ryota; Kondo, Megumi; Tabelin, Carlito Baltazar

    2018-03-06

    Groundwater flow and its geochemical evolution in mines are important not only in the study of contaminant migration but also in the effective planning of excavation. The effects of groundwater on the stability of rock slopes and other mine constructions especially in limestone quarries are crucial because calcite, the major mineral component of limestone, is moderately soluble in water. In this study, evolution of groundwater in a limestone quarry located in Chichibu city was monitored to understand the geochemical processes occurring within the rock strata of the quarry and changes in the chemistry of groundwater, which suggests zones of deformations that may affect the stability of rock slopes. There are three distinct geological formations in the quarry: limestone layer, interbedded layer of limestone and slaty greenstone, and slaty greenstone layer as basement rock. Although the hydrochemical facies of all groundwater samples were Ca-HCO 3 type water, changes in the geochemical properties of groundwater from the three geological formations were observed. In particular, significant changes in the chemical properties of several groundwater samples along the interbedded layer were observed, which could be attributed to the mixing of groundwater from the limestone and slaty greenstone layers. On the rainy day, the concentrations of Ca 2+ and HCO 3 - in the groundwater fluctuated notably, and the groundwater flowing along the interbedded layer was dominated by groundwater from the limestone layer. These suggest that groundwater along the interbedded layer may affect the stability of rock slopes.

  2. Dynamic responses of photosystem II in the Namib Desert shrub, Zygophyllum prismatocarpum, during and after foliar deposition of limestone dust

    International Nuclear Information System (INIS)

    Heerden, P.D.R. van; Krueger, G.H.J.; Kilbourn Louw, M.

    2007-01-01

    The effects of limestone dust deposition on vegetation in desert ecosystems have not yet been reported. We investigated these effects in a succulent shrub from the Namib Desert at a limestone quarry near Skorpion Zinc mine (Namibia). Effects of limestone dust were determined in Zygophyllum prismatocarpum (dollar bush) plants with heavy, moderate and no visible foliar dust cover by means of chlorophyll a fluorescence measurements. Limestone dust deposition decreased overall plant performance through loss of chlorophyll content, inhibition of CO 2 assimilation, uncoupling of the oxygen-evolving complex and decreased electron transport. Importantly, dynamic recovery occurred after termination of limestone extraction at the quarry. Recovery was accelerated by rainfall, mainly because of dust removal from leaves and stimulation of new growth. These results indicate that limestone dust has severe effects on photosynthesis in desert shrubs, but that recovery is possible and that, in arid environments, this process is modulated by rainfall. - Limestone dust deposition reduced photosynthetic capacity in the Namib Desert shrub, Zygophyllum prismatocarpum

  3. Effects of dietary calcium levels and limestone particicle size on the performance, tibia and blood of laying hens

    Directory of Open Access Journals (Sweden)

    K Pelicia

    2011-03-01

    Full Text Available A total of 405 23-week-old ISA® Brown layers were distributed in a completely randomized experimental design in a factorial arrangement with nine treatments consisting of three dietary calcium levels (3.5, 3.75, and 4.5% and three limestone particle sizes (100% fine limestone (FL, 70% FL + 30% coarse limestone (CL and 50% (FL + 50% (CL, with nine replicates of five birds per cage. The following parameters were evaluated: percentage of lay, defective eggs, egg weight, egg mass, feed intake, feed conversion ratio (per kg eggs and per dozen eggs, and mortality. Dietary Ca levels significantly affected lay, with birds fed diets containing 4.5% calcium producing less eggs as compared to those fed 3.0 and 3.75% Ca. Egg production linearly decreased as dietary Ca levels increased, but blood Ca levels (mg/L increased in 28-week-old birds. The interaction of dietary Ca levels and limestone particle sizes resulted in a reduction in tibial ash Ca content as dietary Ca levels increased and as fine limestone was replaced by coarse limestone. It is concluded that a dietary Ca level of 3.75% and 100% fine particle limestone are required to maintain adequate egg production and available Ca blood level.

  4. Cretaceous planktic foraminiferal biostratigraphy of the Calera Limestone, Northern California, USA

    Science.gov (United States)

    Sliter, W.V.

    1999-01-01

    The Calera Limestone is the largest, most stratigraphically extensive limestone unit of oceanic character included in the Franciscan Complex of northern California. The aim of this paper is to place the Calera Limestone at its type locality (Rockaway Beach, Pacifica) in a high-resolution biostratigraphy utilizing planktic foraminifers studied in thin section. A section, about 110 m-thick, was measured from the middle thrust slice exposed by quarrying on the southwest side of Calera Hill at Pacifica Quarry. Lithologically, the section is divided in two units; a lower unit with 73 m of black to dark-grey limestone, black chert and tuff, and an upper unit with 36.8 m of light-grey limestone and medium-grey chert. Two prominent black-shale layers rich in organic carbon occur 11 m below the top of the lower black unit and at the boundary with overlying light-grey unit, yielding a total organic content (TOC) of 4.7% and 1.8% t.w., respectively. The fossiliferous Calera Limestone section measured at Pacifica Quarry, from the lower black shale, contains eleven zones and three subzones that span approximately 26 m.y. from the early Aptian to the late Cenomanian. The zones indentified range from the Globigerinelloides blowi Zone to the Dicarinella algeriana Subzone of the Rotalipora cushmani Zone. Within this biostratigraphic interval, the Ticinella bejaouaensis and Hedbergella planispira Zones at the Aptian/Albian boundary are missing as are the Rotalipora subticinensis Subzone of the Biticinella breggiensis Zone and the overlying Rotalipora ticinensis Zone in the late Albian owing both to low-angle thrust faulting and to unconformities. The abundance and preservation of planktic foraminifers are poor in the lower part and improve only within the upper G. algerianus Zone. The faunal relationship indicate that the lower black shale occurs in the upper part of the G. blowi Zone and correlates with the Selli Event recognized at global scale in the early Aptian. The upper black

  5. Lithofacies palaeogeography and biostratigraphy of the lowermost horizons of the Middle Triassic Hallstatt Limestones (Argolis Peninsula, Greece

    Directory of Open Access Journals (Sweden)

    Fotini A. Pomoni

    2013-07-01

    Taking into consideration the present location of the Hallstatt Formation, in the context of the Hellenides, an area suitable for the deposition of the Hallstatt Limestones, should be located between the sub-Pelagonian (western part of the Pelagonian zone and Pindos geotectonic zones, which during the Triassic corresponded to a platform slope and a deep ocean, respectively. The widespread Middle Triassic Han Bulog Limestones (ammonoid-bearing pelagic limestones from Triassic successions of the Eastern Alps (Dinarides, Hellenides may have formed partly in similar slope environments.

  6. Holothurian sclerites and conodonts in the Upper Carnian (Tuvalian and Norian Limestones in the Central Kanmik Alps

    Directory of Open Access Journals (Sweden)

    Anton Ramovš

    1992-12-01

    Full Text Available Near Bivouac under the Skuta Mountain (locality 1 in the central Kamnik Alps Upper Carnian Limestones were determined with conodont Epigondolella nodosa Hayashi, holothurian sclerites Calclamnella consona Mostler and C. regularis Stefanov, ammonites and other fossils similar to deeper marine Hallstatt facies of Northern Limestone Alps.Conodonts Epigondolella abneptis (Huckriede and very rich holothurian fauna proved the Norian age for bedded limestones with very frequent large chert nodules on the south slope of the Skuta and on Sleme (loc. 2 and 3. They representdeeper marine facies and a distinct development of the Lower Norian

  7. Vulnerable, But Why? Post-Traumatic Stress Symptoms in Older Adults Exposed to Hurricane Sandy.

    Science.gov (United States)

    Heid, Allison R; Christman, Zachary; Pruchno, Rachel; Cartwright, Francine P; Wilson-Genderson, Maureen

    2016-06-01

    Drawing on pre-disaster, peri-disaster, and post-disaster data, this study examined factors associated with the development of post-traumatic stress disorder (PTSD) symptoms in older adults exposed to Hurricane Sandy. We used a sample of older participants matched by gender, exposure, and geographic region (N=88, mean age=59.83 years) in which one group reported clinically significant levels of PTSD symptoms and the other did not. We conducted t-tests, chi-square tests, and exact logistic regressions to examine differences in pre-disaster characteristics and peri-disaster experiences. Older adults who experienced PTSD symptoms reported lower levels of income, positive affect, subjective health, and social support and were less likely to be working 4 to 6 years before Hurricane Sandy than were people not experiencing PTSD symptoms. Those developing PTSD symptoms reported more depressive symptoms, negative affect, functional disability, chronic health conditions, and pain before Sandy and greater distress and feelings of danger during Hurricane Sandy. Exact logistic regression revealed independent effects of preexisting chronic health conditions and feelings of distress during Hurricane Sandy in predicting PTSD group status. Our findings indicated that because vulnerable adults can be identified before disaster strikes, the opportunity to mitigate disaster-related PTSD exists through identification and resource programs that target population subgroups. (Disaster Med Public Health Preparedness. 2016;10:362-370).

  8. Genesis of Hurricane Sandy (2012) Simulated with a Global Mesoscale Model

    Science.gov (United States)

    Shen, Bo-Wen; DeMaria, Mark; Li, J.-L. F.; Cheung, S.

    2013-01-01

    In this study, we investigate the formation predictability of Hurricane Sandy (2012) with a global mesoscale model. We first present five track and intensity forecasts of Sandy initialized at 00Z 22-26 October 2012, realistically producing its movement with a northwestward turn prior to its landfall. We then show that three experiments initialized at 00Z 16-18 October captured the genesis of Sandy with a lead time of up to 6 days and simulated reasonable evolution of Sandy's track and intensity in the next 2 day period of 18Z 21-23 October. Results suggest that the extended lead time of formation prediction is achieved by realistic simulations of multiscale processes, including (1) the interaction between an easterly wave and a low-level westerly wind belt (WWB) and (2) the appearance of the upper-level trough at 200 hPa to Sandy's northwest. The low-level WWB and upper-level trough are likely associated with a Madden-Julian Oscillation.

  9. The impact of Hurricane Sandy on the mental health of New York area residents.

    Science.gov (United States)

    Schwartz, Rebecca M; Sison, Cristina; Kerath, Samantha M; Murphy, Lisa; Breil, Trista; Sikavi, Daniel; Taioli, Emanuela

    2015-01-01

    To evaluate the long-term psychological impact of Hurricane Sandy on New York residents. Prospective, cross-sectional study. Community-based study. From October 2013 to February 2015, 669 adults in Long Island, Queens, and Staten Island completed a survey on their behavioral and psychological health, demographics, and hurricane impact (ie, exposure). Depression, anxiety, and post-traumatic stress disorder (PTSD). Using multivariable logistic regression models, the relationships between Hurricane Sandy exposure and depression, anxiety, and PTSD were examined. Participants experienced an average of 3.9 exposures to Hurricane Sandy, most of which were related to property damage/loss. Probable depression was reported in 33.4 percent of participants, probable anxiety in 46 percent, and probable PTSD in 21.1 percent. Increased exposure to Hurricane Sandy was significantly associated with a greater likelihood of depression (odds ratio [OR] = 1.09, 95% confidence interval [CI]: 1.04-1.14), anxiety (OR = 1.08, 95% CI: 1.03-1.13), and probable PTSD (OR = 1.32, 95% CI: 1.23-1.40), even after controlling for demographic factors known to increase susceptibility to mental health issues. Individuals affected by Hurricane Sandy reported high levels of mental health issues and were at an increased risk of depression, anxiety, and PTSD in the years following the storm. Recovery and prevention efforts should focus on mental health issues in affected populations.

  10. Fault architecture and growth in clay-limestone alternations: insights from field observations in the SE Basin, France

    International Nuclear Information System (INIS)

    Rocher, M.; Roche, V.; Homberg, C.

    2012-01-01

    Document available in extended abstract form only. The Callovo-Oxfordian (COX) clayey formation is currently studied by Andra in 'Meuse/Haute- Marne' (MHM), eastern Paris basin (France), for hosting a disposal of high level and intermediate, long-lived radioactive waste. As an independent organisation performing safety reviews for the Nuclear Safety Authority, IRSN conducts studies in support of the review of this disposal project. This nearly 130 m-thick clayey formation is surrounded by two 250 m-thick limestone formations. In such limestone/clay alternations, tectonic fracturing is often observed within limestones and propagates in some cases to clay layers. Such a propagation through the COX within or close to the disposal area could diminish its containment ability by creating preferential pathways of radioactive solute towards limestones. Nevertheless, minor to moderate fracturing is difficult to investigate in hectometre scale multilayer systems such as COX: seismic reflexion surveys only provide data on major faults, drilling data are too localised and clays have a 'bad-land' aspect at surface. The aim of this study is to provide a model of fracturing across clay-limestone alternations so as to strengthen the assessment of their possible development. We thus investigated fracturing within decametre-sized clay-limestone alternations, located in the South-Eastern Basin (France), to determine the evolution of fault architecture during its growth. After analysis of the possible scale effects using data from other analogous fields, an application to the COX in MHM is presented. We studied minor normal faults that reflect various stages of development, from simple fault planes restricted to limestones to complex fault zones propagated across several clay-limestone layers. The analysis of the fault characteristics, the construction of displacement profiles and the results obtained using numerical models enlighten fault growth processes, i.e. nucleation

  11. Evaluation of steel slag and crushed limestone mixtures as subbase material in flexible pavement

    Directory of Open Access Journals (Sweden)

    Ahmed Ebrahim Abu El-Maaty Behiry

    2013-03-01

    Full Text Available Steel slag is produced as a by-product during the oxidation of steel pellets in an electric arc furnace. This by-product that mainly consists of calcium carbonate is broken down to smaller sizes to be used as aggregates in pavement layers. They are particularly useful in areas where a good-quality aggregate is scarce. This research study was conducted to evaluate the effect of quantity of steel slag on the mechanical properties of blended mixes with crushed limestone aggregates, which used as subbase material in Egypt. Moreover, a theoretical analysis was employed to estimate the resistance for failure factors such as vertical deformations, vertical and radial stresses and vertical strains of subbase under overweight trucks loads. These loads cause severe deterioration to the pavement and thus reduce its life. The results indicated that the mechanical characteristics, and the resistance factors were improved by adding steel slag to the crushed limestone.

  12. Compositional characterization of French limestone: a new tool for art historians

    International Nuclear Information System (INIS)

    Holmes, L.L.; Harbottle, G.; Blanc, A.

    1994-01-01

    Limestone from quarries known to medieval craftsmen and from the monuments they built and embellished, as well as from carvings now in museum collections, has been characterized by neutron activation analysis. Specimens form 38 quarries in the Lutetian and Jurassic limestone formations of France and from sculptures in American and French museums have been tested, and the results have been compiled in a data base to which art historians may refer when attempting to determine provenance for sculptures. Multivariate statistical analysis of concentration data shows stone form a particular quarry in the Paris basin to be compositionally homogeneous and distinguishable from other quarries in the same formation. The same approach to data related to quarries near the Burgundian abbey of Cluny finds general agreement between classifications based on compositional and on petrographic data. (Author)

  13. Intermediate-scale sodium-concrete reaction tests with basalt and limestone concrete

    International Nuclear Information System (INIS)

    Hassberger, J.A.; Muhlestein, L.D.

    1981-01-01

    Ten tests were performed to investigate the chemical reactions and rate and extent of attack between sodium and basalt and limestone concretes. Test temperatures ranged from 510 to 870 0 C (950 to 1600 0 F) and test times from 2 to 24 hours. Sodium hydroxide was added to some of the tests to assess the impact of a sodium hydroxide-aided reaction on the overall penetration characteristics. Data suggest that the sodium penetration of concrete surfaces is limited. Penetration of basalt concrete in the presence of sodium hydroxide is shown to be less severe than attack by the metallic sodium alone. Presence of sodium hydroxide changes the characteristics of sodium penetration of limestone concrete, but no major differences in bulk penetration were observed as compared to penetration by metallic sodium

  14. Biological effects of long term fine limestone tailings discharge in a fjord ecosystem.

    Science.gov (United States)

    Brooks, Lucy; Melsom, Fredrik; Glette, Tormod

    2015-07-15

    Benthic infaunal data collected from 1993 to 2010 were analysed to examine the effect of long term discharge of fine limestone tailings on macrofaunal species assemblages in a fjord. Relative distance from the outfall and proportion of fine tailings in the sediment were correlated with benthic community structure. Diversity decreased with increasing proportion of fine tailings. Biological Traits Analysis (BTA) was used to explore the temporal and spatial effects of the tailings gradient on macrofaunal functional attributes. BTA revealed that all stations along a pressure gradient of fine limestone tailings were dominated by free-living species. As the proportion of fine tailings in the sediment increased, there was an increase in fauna that were smaller, highly mobile, living on or nearer the surface sediment, with shorter lifespans. There was a decrease in permanent tube dwellers, those fauna with low or no mobility, that live deeper in the sediment and have longer lifespans (>5 yrs). Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. Physiological and behavioral response of stonefly nymphs to enhanced limestone treatment of acid mine drainage

    Energy Technology Data Exchange (ETDEWEB)

    Cole, M.B.; Arnold, D.E.; Watten, B.J. [ABR Inc., PO Box 249, OR (USA). Environmental Research and Services

    2001-07-01

    A new acid mine drainage (AMD) treatment system uses pulsed, fluidized beds of limestone, and carbon dioxide pretreatment of influent AMD to enhance limestone neutralization of AMD. Laboratory studies were carried out to evaluate the behavior and physiology of larval stoneflies (Pteronarcys proteus, Plecoptera) exposed to effluents produced by the treatment system. Survival, sodium balance, drift, and feeding responses by P. proteus to treated and untreated AMD were examined. P. proteus nymphs exhibited significant losses of whole body sodium in exposures to untreated AMD. Nymphs exposed to treated effluents experienced no loss of whole-body sodium. No significant differences in feeding or drift behavior occurred between nymphs exposed to treated effluents and those exposed to AMD-free controls. The treatment system, with and without CO{sub 2} pretreatment, provided water that was not toxic to the test animals, and that allowed normal behavioral and physiological function.

  16. Hydrobiogeochemical interactions in 'anoxic' limestone drains for neutralization of acidic mine drainage

    Science.gov (United States)

    Robbins, E.I.; Cravotta, C.A.; Savela, C.E.; Nord, G.L.

    1999-01-01

    Processes affecting neutralization of acidic coal mine drainage were evaluated within 'anoxic' limestone drains (ALDs). Influents had pH???3.5 and dissolved oxygen Al3+ and Fe3+ compounds. Cleavage mounts of calcite and gypsum that were suspended within the ALDs and later examined microscopically showed dissolution features despite coatings by numerous bacteria, biofilms, and Fe-Al-Si precipitates. In the drain exhibiting the greatest flow reduction, Al-hydroxysulfates had accumulated on limestone surfaces and calcite etch points, thus causing the decline in transmissivity and dissolution. Therefore, where Al loadings are high and flow rates are low, a pre-treatment step is indicated to promote Al removal before diverting acidic mine water into alkalinity-producing materials. ?? 1998 Elsevier Science Ltd.

  17. Evaluation of modeling approaches to simulate contaminant transport in a fractured limestone aquifer

    DEFF Research Database (Denmark)

    Mosthaf, Klaus; Fjordbøge, Annika Sidelmann; Broholm, Mette Martina

    in fractured limestone aquifers. The model comparison is conducted for a contaminated site in Denmark, where a plume of dissolved PCE has migrated through a fractured limestone aquifer. Field data includes information on spill history, distribution of the contaminant (multilevel sampling), geology...... and hydrogeology. To describe the geology and fracture system, data from borehole logs and cores was combined with an analysis of heterogeneities and fractures from a nearby excavation and pump test data. We present how field data is integrated into the different model concepts. A challenge in the use of field...... and remediation strategies. Each model is compared with field data, considering both model fit and model suitability. Results show a considerable difference between the approaches, and that it is important to select the right one for the actual modeling purpose. The comparison with data showed how much...

  18. Comparison of different modeling approaches to simulate contaminant transport in a fractured limestone aquifer

    DEFF Research Database (Denmark)

    Mosthaf, Klaus; Rosenberg, L.; Balbarini, Nicola

    . Given available field data and model purpose, this paper therefore aims to develop, examine and compare modeling approaches for transport of contaminants in fractured limestone aquifers. The model comparison was conducted for a contaminated site in Denmark, where a plume of a dissolved contaminant (PCE...... was combined with an analysis of heterogeneities and fractures from a nearby excavation (analog site). Methods for translating the geological information and fracture mapping into each of the model concepts were examined. Each model was compared with available field data, considering both model fit...... of field data is the determination of relevant hydraulic properties and interpretation of aqueous and solid phase contaminant concentration sampling data. Traditional water sampling has a bias towards fracture sampling, however concentrations in the limestone matrix are needed for assessing contaminant...

  19. Mechanical and chemical compaction in fine-grained shallow-water limestones.

    Science.gov (United States)

    Shinn, E.A.; Robbin, D.M.

    1983-01-01

    Significant mechanical compaction resulted from pressures simulating less than 305 m of burial. Increasing loads to an equivalent of more than 3400 m did not significantly increase compaction or reduce sediment core length. Chemical compaction (pressure dissolution) was detected only in sediment cores compacted to pressures greater than 3400 m of burial. These short-term experiments suggest that chemical compaction would begin at much shallower depths given geologic time. Compaction experiments that caused chemical compaction lend support to the well-established hypothesis; that cement required to produce a low-porosity/low-permeability fine-grained limestone is derived internally. Dissolution, ion diffusion, and reprecipitation are considered the most likely processes for creating significant thicknesses of dense limestone in the geologic record. Continuation of chemical compaction after significant porosity reduction necessitates expulsion of connate fluids, possibly including hydrocarbons. -from Authors

  20. Soil-gas diffusivity fingerprints of the dual porosity system in fractured limestone

    DEFF Research Database (Denmark)

    Claes, Niels; Chamindu, D.T.K.K.; Jensen, Jacob Birk

    2010-01-01

    processes are mostly limited to hydrogeological (water and solute) transport studies with very poor attention to the gaseous phase transport studies (Kristensen et al. 2010). This study characterizes fractured limestone soils for gas diffusion based on three different gas diffusivity fingerprints. The first...... fingerprint is a two-parameter exponential model, which mainly describes the gas diffusivity in the limestone matrix while taking both fracture connectivity and matrix pore connectivity into account. With the second fingerprint, we make a close observation of the tortuous matrix pore network by means...... of a modified Buckingham (1904) pore connectivity factor (X*). The third fingerprint of the fracture network involves the average angle of diffusion α (Moldrup et al. 2010), a parameter which characterizes the average angle at which the fractures are penetrating the sample....

  1. Arbuscular mycorrhizal fungi in a semi-arid, limestone mining-impacted area of Brazil

    Directory of Open Access Journals (Sweden)

    Thaís Teixeira-Rios

    2013-12-01

    Full Text Available The main goal of this study was to determine the diversity and activity of arbuscular mycorrhizal fungi (AMF in an area degraded by limestone mining within the semi-arid region of Brazil known as the caatinga (shrublands. Near a limestone quarry, we selected two areas of caatinga (preserved and degraded for study. The number of glomerospores did not differ significantly between the two areas. There was a trend toward the most probable number of infective propagules being higher in the degraded area. Twenty AMF taxa were identified in the two sampled areas, species richness, diversity and evenness being higher in the preserved area. Two species of Racocetra represent new records for the semi-arid region of Brazil. Glomerospore production and AMF species richness were unaffected by mining activity in the study area.

  2. Investigations of a Cretaceous limestone with spectral induced polarization and scanning electron microscopy

    DEFF Research Database (Denmark)

    Johansson, Sara; Sparrembom, Charlotte; Fiandaca, Gianluca

    2017-01-01

    limestone was carried out in the Kristianstad basin, Sweden. The time domain IP data was processed with a recently developed method in order to suppress noise from the challenging urban setting in the survey area. The processing also enabled extraction of early decay times resulting in broader spectra...... in early time ranges for bedrock characterization. The inverted sections showed variations within the limestone that could be caused by variations in texture and composition. Samples from a deep drilling in the Kristianstad basin were investigated with scanning electron microscopy and energy dispersive X......Characterization of varying bedrock properties is a common need in various contexts, ranging from large infrastructure pre-investigations to environmental protection. A direct current resistivity and time domain induced polarization (IP) survey aiming to characterize properties of a Cretaceous...

  3. Physico-chemical investigations of limestones from different localities in the Republic of Macedonia

    International Nuclear Information System (INIS)

    Arabadzhiev, Dimitrios M.; Stefov, Viktor; Boev, Blazho

    2001-01-01

    Physico-chemical investigations were carried out for limestone samples at different localities in the Republic of Macedonia: mine for nonmetals O graiden , Strumica (sample-granulation below: 4, 10, 20, 32, 40, 63 and 90 gm), A.D. M ikrogranulat , Gostivar, mine 'Banjani' - Skopje, mine 'Toplica' near Demir Hisar and from the separation of GP Mavrovo, Skopje, located near Pletvar. Investigation of samples from the previously mentioned localities were carried out using different methods: volumetry, gravimetry, UV-VIS and infrared spectroscopy, as well as atomic absorption and X-ray fluorescence spectrometry, X-ray diffraction and flame photometry. The obtained results lead to the conclusion that all granulometric classes of the limestone samples from 'Ograzhden', Strumica, are of the best quality. (Original)

  4. Paleokarst processes in the Eocene limestones of the Pyramids Plateau, Giza, Egypt

    Science.gov (United States)

    El Aref, M. M.; Refai, E.

    The Eocene limestones of the Pyramids plateau are characterized by landforms of stepped terraced escarpment and karst ridges with isolated hills. The carbonate country rocks are also dominated by minor surface, surface to subsurface and subsurface solution features associated with karst products. The systematic field observations eludicate the denudation trend of the minor solution features and suggest the origin of the regional landscapes. The lithologic and structural characters of the limestone country rocks comprise the main factors controlling the surface and subsurface karst evolution. The development of the karst features and the associated sediments in the study area provides information on the paleohydrolic, chemical and climatic environments involved in the origin of the karstification.

  5. Limestone: some observations on luminescence in the region of 360 nm

    International Nuclear Information System (INIS)

    Galloway, R.B.

    2003-01-01

    An empirical study of luminescence around 360 nm from limestone is presented. Thermoluminescence glow curves from natural limestone show broad peaks at 440 deg. C, 350 deg. C, 530 deg. C and 286 deg. C in order of decreasing amplitude in contrast to the usual observation, for luminescence around 535 nm, of a sharp peak at 286 deg. C with a broader less intense peak at 350 deg. C. Recuperation occurs around 350 deg. C and 525 deg. C, which has a time dependence consistent with quantum tunnelling. Dependent on the history of heating and light exposure of the sample, sharp peaks at about 325 deg. C and 425 deg. C can be observed. Laboratory irradiated limestone shows a peak at 140 deg. C. The stimulation of luminescence by light of 470 nm with preheating at 145 deg. C for 300 s, shows an increasing signal for successive cycles of measurement associated with the heating, light exposure having little influence. Beta irradiation of a sample, with the same measurement conditions, gives a signal which increases in proportion to radiation dose but which does not survive storage for 17 h. Time resolved luminescence spectra, with no preheating, show a luminescence lifetime between stimulation and emission of less than a few μs for natural limestone, and an exponential increase in signal with increase in temperature (over the rang 20-167 deg. C) during stimulation. A signal proportional to laboratory applied beta dose is measurable at room temperature, with lifetime between stimulation and emission of this signal of 35 μs, but it does not survive heating to 100 deg. C

  6. [Effects of variable temperature on organic carbon mineralization in typical limestone soils].

    Science.gov (United States)

    Wang, Lian-Ge; Gao, Yan-Hong; Ding, Chang-Huan; Ci, En; Xie, De-Ti

    2014-11-01

    Soil sampling in the field and incubation experiment in the laboratory were conducted to investigate the responses of soil organic carbon (SOC) mineralization to variable temperature regimes in the topsoil of limestone soils from forest land and dry land. Two incubated limestone soils were sampled from the 0-10 cm layers of typical forest land and dry land respectively, which were distributed in Tianlong Mountain area of Puding county, Guizhou province. The soils were incubated for 56 d under two different temperature regimes including variable temperature (range: 15-25 degrees C, interval: 12 h) and constant temperature (20 degrees C), and the cumulative temperature was the same in the two temperature treatments. In the entire incubation period (56 d), the SOC cumulative mineralization (63.32 mg x kg(-1)) in the limestone soil from dry land (SH) under the variable temperature was lower than that (63.96 mg x kg(-1)) at constant 20 degrees C, and there was no significant difference in the SOC cumulative mineralization between the variable and constant temperature treatments (P variable temperature was significantly lower than that (209.52 mg x kg(-1)) at constant 20 degrees C. The results indicated that the responses of SOC mineralization to the variable temperature were obviously different between SL and SH soils. The SOC content and composition were significantly different between SL and SH soils affected by vegetation and land use type, which suggested that SOC content and composition were important factors causing the different responses of SOC mineralization to variable temperature between SL and SH soils. In addition, the dissolved organic carbon (DOC) content of two limestone soils were highly (P variable temperature mainly influenced SOC mineralization by changing microbial community activity rather than by changing microbial quantity.

  7. Towards Early Age Characterisation of Eco-Concrete Containing Blast-Furnace Slag and Limestone Filler

    OpenAIRE

    Carette, Jerome

    2015-01-01

    It is estimated that concrete represents 5% of the anthropogenic CO2 emissions, mainly originating from the production of cement, the most essential component of concrete. The recent awareness to the environmental challenges facing our civilization has led the cement industry to consider substituting cement by mineral additions, by-products of existing industries. In this work, a combination of limestone filler and blast furnace slag is used to design an “eco-concrete”, defined as a concrete ...

  8. Estimation of deep infiltration in unsaturated limestone environments using cave lidar and drip count data

    OpenAIRE

    Mahmud, K.; Mariethoz, G.; Baker, A.; Treble, P. C.; Markowska, M.; McGuire, E.

    2016-01-01

    Limestone aeolianites constitute karstic aquifers covering much of the western and southern Australian coastal fringe. They are a key groundwater resource for a range of industries such as winery and tourism, and provide important ecosystem services such as habitat for stygofauna. Moreover, recharge estimation is important for understanding the water cycle, for contaminant transport, for water management, and for stalagmite-based paleoclimate reconstructions. Caves offer a n...

  9. Block Volume Estimation from the Discontinuity Spacing Measurements of Mesozoic Limestone Quarries, Karaburun Peninsula, Turkey

    OpenAIRE

    Elci, Hakan; Turk, Necdet

    2014-01-01

    Block volumes are generally estimated by analyzing the discontinuity spacing measurements obtained either from the scan lines placed over the rock exposures or the borehole cores. Discontinuity spacing measurements made at the Mesozoic limestone quarries in Karaburun Peninsula were used to estimate the average block volumes that could be produced from them using the suggested methods in the literature. The Block Quality Designation (BQD) ratio method proposed by the authors has been found to ...

  10. Mississippian reef development in the Cracoe Limestone Formation of the southern Askrigg Block, North Yorkshire, UK

    OpenAIRE

    Waters, C.N.; Haslam, R.B.; Cózar, P.; Somerville, I.D.; Millward, D.; Woods, M.

    2017-01-01

    The southern margin of the Askrigg Block around Cracoe, North Yorkshire, shows a transition from carbonate ramp to reef-rimmed shelf margin, which, based on new foraminiferal/algal data, is now constrained to have initiated during the late Asbian. A late Holkerian to early Asbian ramp facies that included small mudmounds developed in comparatively deeper waters, in a transition zone between the proximal ramp, mudmound-free carbonates of the Scaleber Quarry Limestone Member (Kilnsey Formation)...

  11. Limestone and oyster shell for brown layers in their second egg production cycle

    Directory of Open Access Journals (Sweden)

    CC Pizzolante

    2011-06-01

    Full Text Available This study aimed at evaluating the effect of dietary calcium levels and the replacement of calcium sources with different particle size compositions on the performance and egg quality of brown layers in their second egg production cycle. A randomized block experimental design was applied with 12 treatments in a 3x4 factorial arrangement: three calcium levels (2.6, 3.2, 3.8 % and four combinations of calcium sources (1- 100% fine limestone (FL, 2- 50% FL + 50% coarse limestone (CL, 3- 50% FL and 50% oyster shell (OS, 4- 50% FL and 25% CL+ 25 %OS, with six replicates of eight birds each. Calcium sources were analyzed for geometric mean diameter (GMD and in-vitro solubility. The following performance and egg quality parameters were evaluated: egg weight (EW, g, egg production (% Eggs, egg mass (EM %, feed intake (FI g, feed conversion ratio (FCR kg/dz and FCR kg/kg, mortality (% Mort., specific egg gravity (SG, percentages of yolk (Y%, albumen (Alb% and eggshell (ES%, eggshell thickness (EST, eggshell breaking strength (BS, eggshell weight per surface area (EWSA, Haugh unit (HU, yolk index (YI and yolk color. Performance and internal egg quality were not affected by the treatments (p>0.05. Blocks had a significant effect on (p<0.05 FI and FCR (kg/dz and kg/kg. Treatments significantly influenced external egg quality, which improved as dietary calcium levels increases and when up to 50% fine limestone was replaced by combinations of coarse limestone with oyster shell.

  12. Stability of an anaerobic single reactor filled with dolomitic limestone with increased organic load of sugarcane

    Directory of Open Access Journals (Sweden)

    Maria Magdalena Ribas Döll

    2017-12-01

    Full Text Available The anaerobic single-stage reactor was evaluated to treat vinasse and to evaluate its stability. This bench reactor was filled with dolomitic limestone with a horizontal plug flow to simulate a drainage channel. The experiment lasted 129 days while the reactor was submitted to different applied organic concentrations (chronologically applied: 3.0; 5.0; 12.0; 9.0 and 7.5 g L-1 as COD, chemical oxygen demand. COD removals were 50% and 9% with 3.0 and 7.5 g L-1, respectively. With 12.0 g L-1, reactor efficiency increased to 33%, with an abrupt drop to 3% on the 84th day. Therefore, in order to avoid reactor collapse, a remedial measure was necessary. The system remained in batch without feeding for 19 days (from the 85th to the 104th day with 9.0 g L-1. Afterwards, it was observed that the performance of the system tended to stabilize, reaching 47% with 7.5 g L-1 in the 118th day. At the end of the experiment, the potassium content of the wastewater decreased from 800 mg L-1 to 594 mg L-1 (on an average 25% and calcium and magnesium increased within the reactor liquor. The dissolution of the limestone inside the liquor reactor probably caused this result. After the treatment with limestone, the average pH value of the effluent increased from 4.9 to over 6.0 in all organic concentrations. It could be concluded that the reactor filled with dolomitic limestone in these operational conditions assured a low efficiency in COD removal, potassium reduction, increasing values of pH, alkalinity, calcium and magnesium. The instability was observed when there was increase in organic load to 12 g L-1 with subsequent recovery.

  13. Properties, sustainability and elevated temperature behavior of concrete containing Portland limestone cement

    Science.gov (United States)

    El-Hawary, Moetaz; Ahmed, Mahmoud

    2017-09-01

    The utilization of some type of cheap filler as partial cement replacement is an effective way of improving concrete sustainability. With the recent trends to reduce water to cement ratio and improve compaction, there is no enough space or water for complete hydration of cement. This means that actually, a portion of mixed cement acts as expensive filler. Replacing this portion with cheaper filler that requires less energy to produce is, therefore, beneficial. Crushed limestone is the most promising filler. This work is to investigate the effect of the amount of limestone fillers on the sustainability and the fresh and mechanical properties of the resulting concrete. A rich mix is designed with a low water/cement ratio of 0.4. Lime is introduced as a replacement percentage of cement. Ratios of 0, 10, 20 and 30% were used. Slump, compressive strength, specific gravity and water absorption are evaluated for every mix. In addition, the effect of the amount of lime on the residual strength of concrete subjected to elevated temperatures is also investigated. Samples are subjected to six different temperature stations of 20, 100, 200, 300, 500 and 700°C for six hours before being cooled and subsequently tested for compressive strength and specific gravity. Sustainability of the tested mixes is evaluated through reductions in the emitted carbon dioxide, energy and reduction in cost. Based on the annual use of concrete in Kuwait, the sustainability benefits resulting from the use of limestone filler in Kuwait are evaluated and assessed. The paper is concluded with the recommendation of the use of 15% limestone filler as partial cement replacement where the properties and the behavior under high temperature of the resulting concrete are almost the same as those of conventional concrete with considerable cost and sustainability benefits.

  14. Determination of calcium and iron in limestone by X-ray fluorescence method

    International Nuclear Information System (INIS)

    Sovtsova, M.K.

    1977-01-01

    The results of determining calcium and iron content in limestone by X-ray fluorescence method are described. The 109 Cd isotape was chosen as a source for excitation, as it permited to reduce the concentration degeneration in the range of large Ca contents due to the larger energy of the primary radiation. The root-mean-square deviation from the data of chemical analysis was +-0.02%FeO and +-0.22%CaO

  15. Dinosaur footprints in the Upper Turonian-Coniacian limestone in the Krnica Bay (NE Istria, Croatia

    Directory of Open Access Journals (Sweden)

    Alenka Mauko

    2003-06-01

    Full Text Available Three isolated footprints and one trackway that can be attributed to bipedal dinosaur, from a limestone bed in vicinity of Požara promontory, Krnica Bay, are described. According to the stratigraphic position the footprints are late Turonian to Coniacian in age.This is the first record of dinosaur remains in the Turonian-Coniacian and the youngest footprint site on the Adriatic-Dinaric Carbonate Platform described thus far.

  16. Effects of sodium polyacrylate on water retention and infiltration capacity of a sandy soil.

    Science.gov (United States)

    Zhuang, Wenhua; Li, Longguo; Liu, Chao

    2013-01-01

    Based on the laboratory study, the effects of sodium polyacrylate (SP) was investigated at 5 rates of 0, 0.08, 0.2, 0.5, and 1%, on water retention, saturated hydraulic conductivity(Ks), infiltration characteristic and water distribution profiles of a sandy soil. The results showed that water retention and available water capacity effectively increased with increasing SP rate. The Ks and the rate of wetting front advance and infiltration under certain pond infiltration was significantly reduced by increasing SP rate, which effectively reduced water in a sandy soil leaking to a deeper layer under the plough layer. The effect of SP on water distribution was obviously to the up layer and very little to the following deeper layers. Considering both the effects on water retention and infiltration capacity, it is suggested that SP be used to the sandy soil at concentrations ranging from 0.2 to 0.5%.

  17. A study on the aseismic safety of the experimental VHTR on the dense sandy layer

    International Nuclear Information System (INIS)

    Fujita, Shigeki; Ito, Yoshio; Baba, Osamu; Suzuki, Hideyuki; Takewaki, Naonobu; Kondo, Tsukasa; Yoshimura, Takashi; Yamada, Hitoshi.

    1986-12-01

    A series of studies has been carried out in 1983 and 1985 for the purpose of confirming the aseismic safety of the Experimental VHTR on the dense sandy layer. In 1983, effect of some of soil properties on seismic responses of the reactor building was estimated by means of parametric survey, and soil properties were estimated by analyzing the obserbed earthquake record. In 1985, literature review, linear, nonlinear parametric analyses and nonlinear simulation analyses were carried to study and compare the analysis method. In addition, seismic response of proposed construction site was estimated with nonlinear analysis method. As a result of these studies, the seismic response of reactor building on the dense sandy layers and wave propagation characteristics of sandy layers are understood. Especially, by means of many parametric studies, the effect of input wave characteristics, soil stiffness, nonlinear characteristics of soil properties and nonlinear analysis method on the reactor building responses were evaluated. (author)

  18. Analysis of storm-tide impacts from Hurricane Sandy in New York

    Science.gov (United States)

    Schubert, Christopher E.; Busciolano, Ronald J.; Hearn, Paul P.; Rahav, Ami N.; Behrens, Riley; Finkelstein, Jason S.; Monti, Jack; Simonson, Amy E.

    2015-07-21

    The hybrid cyclone-nor’easter known as Hurricane Sandy affected the mid-Atlantic and northeastern United States during October 28-30, 2012, causing extensive coastal flooding. Prior to storm landfall, the U.S. Geological Survey (USGS) deployed a temporary monitoring network from Virginia to Maine to record the storm tide and coastal flooding generated by Hurricane Sandy. This sensor network augmented USGS and National Oceanic and Atmospheric Administration (NOAA) networks of permanent monitoring sites that also documented storm surge. Continuous data from these networks were supplemented by an extensive post-storm high-water-mark (HWM) flagging and surveying campaign. The sensor deployment and HWM campaign were conducted under a directed mission assignment by the Federal Emergency Management Agency (FEMA). The need for hydrologic interpretation of monitoring data to assist in flood-damage analysis and future flood mitigation prompted the current analysis of Hurricane Sandy by the USGS under this FEMA mission assignment.

  19. What would happen to Superstorm Sandy under the influence of a substantially warmer Atlantic Ocean?

    Science.gov (United States)

    Lau, William K. M.; Shi, J. J.; Tao, W. K.; Kim, K. M.

    2016-01-01

    Based on ensemble numerical simulations, we find that possible responses of Sandy-like superstorms under the influence of a substantially warmer Atlantic Ocean bifurcate into two groups. In the first group, storms are similar to present-day Sandy from genesis to extratropical transition, except they are much stronger, with peak Power Destructive Index (PDI) increased by 50-80%, heavy rain by 30-50%, and maximum storm size (MSS) approximately doubled. In the second group, storms amplify substantially over the interior of the Atlantic warm pool, with peak PDI increased by 100-160%, heavy rain by 70-180%, and MSS more than tripled compared to present-day Superstorm Sandy. These storms when exiting the warm pool, recurve northeastward out to sea, subsequently interact with the developing midlatitude storm by mutual counterclockwise rotation around each other and eventually amplify into a severe Northeastern coastal storm, making landfall over the extreme northeastern regions from Maine to Nova Scotia.

  20. Superstorm Sandy: How the New York University Psychiatry Residency Training Program Weathered the Storm.

    Science.gov (United States)

    Capasso, Rebecca; Adler, Laura

    2016-10-01

    The teaching hospitals of the New York University psychiatry residency program were evacuated and then closed for a minimum of 3 months in the aftermath of Superstorm Sandy. Faculty and residents were deployed to alternate clinical sites. The authors examine the consequences of Superstorm Sandy and its implications for the New York University psychiatry residency training program. A survey was administered to faculty and residents. The authors tabulated 98 surveys, for which 24 % of faculty and 84 % of residents responded. Among respondents, 61 % believed that being involved in the evacuation of the hospitals was a positive experience. During deployment, most (85 %) found being placed with peers and supervisors to be beneficial, but there were significant disruptions. Despite facing multiple challenges including closed facilities, deployment to nonaffiliated hospitals, and exhausted personal resources, the training program continued to provide accredited clinical experiences, a core curriculum, and supervision for psychiatry residents during and after Superstorm Sandy.

  1. Decomposition and reduction of N2O over Limestone under FBC Conditions

    DEFF Research Database (Denmark)

    Johnsson, Jan Erik; Jensen, Anker; Vaaben, Rikke

    1997-01-01

    The addition of limestone for sulfur retention in FBC has in many cases been observed to influence the emission of N2O. The catalytic activity of N2O over calcined Stevns Chalk for decomposition of N2O in a laboratory fixed bed quartz reactor was measured. It was found that calcined Stevns Chalk...... is a very active catalyst for N2O decomposition in an inert atmosphere, and the presence of 3 vol% CO increased the rate of N2O destruction by a factor of 5 due to the catalytic reduction of N2O by CO. The activity decreased with increasing CO2 concentration, and uncalcined or recarbonated limestone had...... negligible activity. Sulfation of the calcined limestone under oxidizing conditions lowered the activity, however sulfidation under reducing conditions showed that CaS is an active catalyst for the reduction of N2O by CO. Without CO present a gas solid reaction between N2O and CaS takes place and SO2...

  2. Experimental study of the effect of limestone grading on some mechanical properties of concrete

    Directory of Open Access Journals (Sweden)

    Ammari Madiha Z. J.

    2017-01-01

    Full Text Available This study reports the experimental work undertaken to investigate the optimum grading of limestone to be used in concrete mixes. 36 concrete cubes were prepared for testing. Four different Fineness Moduli and grading were tested 2.4, 2.6, 2.92 and 3. For all tests, the cubes were left in curing until testing at the age of 3, 7 and 28 days respectively. Samples were loaded to failure and the average compressive strength was used for comparison purposes. Flow table test has been performed on the fresh concrete directly after mixing to measure workability and the average of the maximum concrete spread parallel to the two edges of the table was recorded. Results revealed that the optimum Fineness Modulus for the limestone to be used as fine aggregate in the concrete mix to get maximum compressive strength is 2.78. The flow table tests revealed an increment in the workability of fresh concrete with higher Fineness Modulus of limestone used in the concrete mix as fine aggregate. The workability of the optimum Fineness Modulus, 2.78, was found to be 412 mm which is a mix with considerable workability. An ideal grading has been recommended in this research study and checked to match the ASTM grading requirements for fine aggregate.

  3. TL glow curve analysis of UV, beta and gamma induced limestone collected from Amarnath holy cave

    Directory of Open Access Journals (Sweden)

    Vikas Dubey

    2015-01-01

    Full Text Available The paper reports themoluminescence glow curve analysis of UV (ultraviolet, β (beta and γ (gamma induced limestone collected from Amarnath holy cave. The collected natural sample was characterized by X-ray diffraction (XRD technique and crystallite size calculated by Scherer's formula. Surface morphology and particle size was calculated by transmission electron microscopy (TEM study. Effect of annealing temperature on collected lime stone examined by TL glow curve study. The limestone was irradiated by UV radiation (254 nm source and the TL glow curve recorded for different UV exposure time. For beta irradiation Sr90 source was used and is shows intense peak at 256 °C with a shoulder peak at higher temperature range. For gamma radiation Co60 source and TL glow curve recorded for different doses of gamma. The kinetic parameters calculation was performed for different glow curve by computerized glow curve deconvolution (CGCD technique. The chemical composition of natural limestone was analyzed by energy dispersive X-ray spectroscopy (EDXS.

  4. The influence of temperature on limestone sulfation and attrition under fluidized bed combustion conditions

    Energy Technology Data Exchange (ETDEWEB)

    Montagnaro, Fabio [Dipartimento di Chimica - Universita degli Studi di Napoli Federico II, Complesso Universitario del Monte di Sant' Angelo, 80126 Napoli (Italy); Salatino, Piero [Istituto di Ricerche sulla Combustione - CNR, Piazzale Vincenzo Tecchio 80, 80125 Napoli (Italy); Dipartimento di Ingegneria Chimica - Universita degli Studi di Napoli Federico II, Piazzale Vincenzo Tecchio 80, 80125 Napoli (Italy); Scala, Fabrizio [Istituto di Ricerche sulla Combustione - CNR, Piazzale Vincenzo Tecchio 80, 80125 Napoli (Italy)

    2010-04-15

    The influence of temperature on attrition of two limestones during desulfurization in a fluidized bed reactor was investigated. Differences in the microstructure of the two limestones were reflected by a different thickness of the sulfate shell formed upon sulfation and by a different value of the ultimate calcium conversion degree. Particle attrition and fragmentation were fairly small under moderately bubbling fluidization conditions for both limestones. An increase of temperature from 850 C to 900 C led to an increase of the attrition rate, most likely because of a particle weakening effect caused by a faster CO{sub 2} evolution during calcination. This weakening effect, however, was not sufficiently strong to enhance particle fragmentation in the bed. The progress of sulfation, associated to the build-up of a hard sulfate shell around the particles, led in any case to a decrease of the extent of attrition. Sulfation at 900 C was less effective than at 850 C, and this was shown to be related to the porosimetric features of the different samples. (author)

  5. Treatment of iron(II)-rich acid mine water with limestone and oxygen.

    Science.gov (United States)

    Mohajane, G B; Maree, J P; Panichev, N

    2014-01-01

    The main components of acid mine water are free acid, sulphate, and Fe²⁺. Limestone is the most cost-effective alkali that can be used for neutralization. The purpose of this investigation was to identify conditions where Fe²⁺ is removed with limestone and simultaneously oxidized with oxygen to Fe³⁺, in a polyvinyl chloride pipe under pressure. Gypsum scaling is prevented by passing rubber balls through the pipe of the so-called Oxygen-Pipe-Neutralization (OPeN) process pilot plant. Two synthetic waters were treated: (A) acid mine water containing 123 mg L⁻¹ Fe²⁺ representing gold mine water, and (B) acid mine water containing 6,032 mg L⁻¹ Fe²⁺ representing coal mine water. Batch studies were carried out in a pipe reactor and showed that the rate of Fe²⁺ oxidation depended on the Fe²⁺ concentration, oxygen pressure, amount of recycled sludge, limestone dosage and the mixing rate. Continuous studies in an OPeN process pilot plant resulted in 100% removal of total acidity from synthetic coal mine water and a 98% removal from synthetic gold mine water. Fe²⁺ was removed completely as precipitated Fe(OH)₃ from both synthetic coal and gold mine water at around pH 7 at 200 and 100 kPa oxygen pressure, respectively.

  6. Report of investigation on underground limestone mines in the Ohio region

    International Nuclear Information System (INIS)

    Byerly, D.W.

    1976-06-01

    The following is a report of investigation on the geologic setting of several underground limestone mines in Ohio other than the PPG mine at Barberton, Ohio. Due to the element of available time, the writer is only able to deliver a brief synopsis of the geology of three sites visited. These three sites and the Barberton, Ohio site are the only underground limestone mines in Ohio to the best of the writer's knowledge. The sites visited include: (1) the Jonathan Mine located near Zanesville, Ohio, and currently operated by the Columbia Cement Corporation; (2) the abandoned Alpha Portland Cement Mine located near Ironton, Ohio; and (3) the Lewisburg Mine located at Lewisburg, Ohio, and currently being utilized as an underground storage facility. Other remaining possibilities where limestone is being mined underground are located in middle Ordovician strata near Carntown and Maysville, Kentucky. These are drift mines into a thick sequence of carbonates. The writer predicts, however, that these mines would have some problems with water due to the preponderance of carbonate rocks and the proximity of the mines to the Ohio River. None of the sites visited nor the sites in Kentucky have conditions comparable to the deep mine at Barberton, Ohio

  7. Hydraulic retention time on vinasse stabilisation with limestone in the acidogenic phase of anaerobic digestion

    Directory of Open Access Journals (Sweden)

    Ismael Plácido Tomielis

    Full Text Available ABSTRACT: The main problem in anaerobic digestion of low-protein residues is the instability caused acidity. The use of limestone at the same time as a neutralizing agent and support material is innovative because stones wear allows the slow release of the calcium carbonate thereby eliminating dispersers. Free calcium content in the system was measured in two plug flow reactors filled with vinasse at initial pH of 4.50. The proportion of 1.8 tonnes of limestone per m³ of vinasse was evaluated at the Hydraulic Retention Times (HRT of 24, 48, 72, 96 and 120 hours, allowing stabilisation at 96 hours. The ratio of Volatile Acids/Total Alkalinity (VA/TA ranged from 0.2 to 0.4 and the pH reached 7.0, at the HRT of 120 hours. Increasing the HRT also increased the volatile total solids (VTS and fixed total solids (TFS in a similar profile to the measured free calcium content, but calcium remained at the appropriate level of 100 to 250mg l-1. The proportion of limestone/vinasse was adequate to ensure stabilisation, but it is not recommended to reduce the HRT below 96 hours due to the risk of compromising the stability of the anaerobic system.

  8. Economical assessment of competitive enhanced limestones for CO2 capture cycles in power plants

    International Nuclear Information System (INIS)

    Romeo, Luis M.; Lara, Yolanda; Lisbona, Pilar; Martinez, Ana

    2009-01-01

    CO 2 capture systems based on the carbonation/calcination loop have gained rapid interest due to promising carbonator CO 2 capture efficiency, low sorbent cost and no flue gases treatment is required before entering the system. These features together result in a competitively low cost CO 2 capture system. Among the key variables that influence the performance of these systems and their integration with power plants, the carbonation conversion of the sorbent and the heat requirement at calciner are the most relevant. Both variables are mainly influenced by CaO/CO 2 ratio and make-up flow of solids. New sorbents are under development to reduce the decay of their carbonation conversion with cycles. The aim of this study is to assess the competitiveness of new limestones with enhanced sorption behaviour applied to carbonation/calcination cycle integrated with a power plant, compared to raw limestone. The existence of an upper limit for the maximum average capture capacity of CaO has been considered. Above this limit, improving sorbent capture capacity does not lead to the corresponding increase in capture efficiency and, thus, reduction of CO 2 avoided cost is not observed. Simulations calculate the maximum price for enhanced sorbents to achieve a reduction in CO 2 removal cost under different process conditions (solid circulation and make-up flow). The present study may be used as an assessment tool of new sorbents to understand what prices would be competitive compare with raw limestone in the CO 2 looping capture systems. (author)

  9. Stable isotope stratigraphy and larger benthic foraminiferal extinctions in the Melinau Limestone, Sarawak

    Science.gov (United States)

    Cotton, Laura J.; Pearson, Paul N.; Renema, Willem

    2014-01-01

    Important long-ranging groups of larger benthic foraminifera (LBF) are known to have become extinct during a period of global cooling and climate disruption at the Eocene-Oligocene transition (EOT) but the precise timing and mechanisms are uncertain. Recent study showed unexpectedly that the LBF extinction in Tanzania occurs very close to the Eocene/Oligocene boundary, as recognised by the extinction of the planktonic foraminiferal Family Hantkeninidae, rather than at the later period of maximum global ice growth and sea-level fall, as previously thought. Here we investigate the same phase of extinction in the Melinau Limestone of Sarawak, on the island of Borneo, Malaysia one of the most complete carbonate successions spanning the Eocene to Lower Miocene. Assemblages of LBF from the Melinau Limestone were studied extensively by Geoffrey Adams during the 1960s-80s, confirming a major extinction during the EOT, but the section lacked independent means of correlation. By analysing rock samples originally studied by Adams and now in the Natural History Museum, London, we provide new bulk stable isotope (δ13C and δ18O) records. This enables us to identify, albeit tentatively, the level of maximum stable isotope excursion and show that the LBF extinction event in the Melinau Limestone occurs below this isotope excursion, supporting the results from Tanzania and indicating that the extinction of LBF close to the Eocene/Oligocene boundary may be a global phenomenon.

  10. Spatial patterns and natural recruitment of native shrubs in a semi-arid sandy land.

    Science.gov (United States)

    Wu, Bo; Yang, Hongxiao

    2013-01-01

    Passive restoration depending on native shrubs is an attractive approach for restoring desertified landscapes in semi-arid sandy regions. We sought to understand the relationships between spatial patterns of native shrubs and their survival ability in sandy environments. Furthermore, we applied our results to better understand whether passive restoration is feasible for desertified landscapes in semi-arid sandy regions. The study was conducted in the semi-arid Mu Us sandy land of northern China with the native shrub Artemisia ordosica. We analyzed population structures and patterns of A. ordosica at the edges and centers of land patches where sand was stabilized by A. ordosica-dominated vegetation. Saplings were more aggregated than adults, and both were more aggregated at the patch edges than at the patch centers. At the patch edges, spatial association of the saplings with the adults was mostly positive at distances 0.3-6.6 m, and turned from positive to neutral, and even negative, at other distances. At the patch centers, the saplings were spaced almost randomly around the adults, and their distances from the adults did not seem to affect their locations. A greater number of A. ordosica individuals emerged at the patch edges than at the patch centers. Such patterns may have resulted from their integrative adjustment to specific conditions of soil water supply and sand drift intensity. These findings suggest that in semi-arid sandy regions, native shrubs that are well-adapted to local environments may serve as low-cost and competent ecological engineers that can promote the passive restoration of surrounding patches of mobile sandy land.

  11. Numerical modeling of salt marsh morphological change induced by Hurricane Sandy

    Science.gov (United States)

    Hu, Kelin; Chen, Qin; Wang, Hongqing; Hartig, Ellen K.; Orton, Philip M.

    2018-01-01

    The salt marshes of Jamaica Bay serve as a recreational outlet for New York City residents, mitigate wave impacts during coastal storms, and provide habitat for critical wildlife species. Hurricanes have been recognized as one of the critical drivers of coastal wetland morphology due to their effects on hydrodynamics and sediment transport, deposition, and erosion processes. In this study, the Delft3D modeling suite was utilized to examine the effects of Hurricane Sandy (2012) on salt marsh morphology in Jamaica Bay. Observed marsh elevation change and accretion from rod Surface Elevation Tables and feldspar Marker Horizons (SET-MH) and hydrodynamic measurements during Hurricane Sandy were used to calibrate and validate the wind-waves-surge-sediment transport-morphology coupled model. The model results agreed well with in situ field measurements. The validated model was then used to detect salt marsh morphological change due to Sandy across Jamaica Bay. Model results indicate that the island-wide morphological changes in the bay's salt marshes due to Sandy were in the range of −30 mm (erosion) to +15 mm (deposition), and spatially complex and heterogeneous. The storm generated paired deposition and erosion patches at local scales. Salt marshes inside the west section of the bay showed erosion overall while marshes inside the east section showed deposition from Sandy. The net sediment amount that Sandy brought into the bay is only about 1% of the total amount of reworked sediment within the bay during the storm. Numerical experiments show that waves and vegetation played a critical role in sediment transport and associated wetland morphological change in Jamaica Bay. Furthermore, without the protection of vegetation, the marsh islands of Jamaica Bay would experience both more erosion and less accretion in coastal storms.

  12. A Stranger in the Midst: Searching for Relict Grains from Rare Meteorite Types in Mid-Ordovician Limestone Strata

    Science.gov (United States)

    Martin, E.; Schmitz, B.

    2016-08-01

    A layer of Mid-Ordovician limestone harbors exceptional amounts of L-chondritic chromite grains. The layer also contains grains from potentially rarer types of meteorites, following the discovery of the fossil meteorite Österplana 065.

  13. Reduction of SO sub 2 emission from a fluidized-bed under staged combustion by coarse limestone

    International Nuclear Information System (INIS)

    Khan, W.Z.; Gibbbs, B.M.

    1998-01-01

    A study was performed to investigate the effect of course limestone on the reduction of SO sub 2 emission from a fluidized-bed under staged combustion. The limestone of 1.2-2.5 mm size was premixed with fine coal of 1-3 mm size and fed under bed. The staging levels, bed height, and Ca/S ratio was fixed at 70:30, 30 cm and 3:1, respectively. A maximum of around 50% reduction in SO sub 2 emissions was achieved at both excess air of 20 and 40% and at 830 deg. C. bed temperature. The SO sub 2 emissions were very sensitive to bed temperature. The course limestone was found better in desulfurization efficiency at lower temperature than fine limestone. (author)

  14. Discontinuity surfaces and event stratigraphy of Okha Shell Limestone Member: Implications for Holocene sea level changes, western India

    Science.gov (United States)

    Bhonde, Uday; Desai, Bhawanisingh G.

    2011-08-01

    The Okha Shell Limestone Member of Chaya Formation is the coarse grained, shell rich deposit commonly recognized as the beach rocks. It has been age bracketed between Late Pleistocene and Holocene. Late Quaternary sea level changes have been studied with beach rocks along the Saurashtra coastal region. The present study has been carried out in the Okhamandal area of the Saurashtra peninsula especially on the Okha Shell Limestone Member as exposed at various locations along the coast from north to south. Temporal and spatial correlations of the observations have revealed three events in the Okha Shell Limestone Member of Chaya Formation that are correlated laterally. The events show depositional breaks represented by discontinuity surfaces, the taphofacies varieties and ichnological variations. The present study in the context of available geochrnological data of the region suggests a prominent depositional break representing low sea level stand (regression) during an Early Holocene during the deposition of Okha Shell Limestone Member.

  15. Nitrogen utilization and digestibility of amino acids by lambs fed a high-concentrate diet with limestone or magnesium oxide.

    Science.gov (United States)

    Christiansen, M L; Webb, K E

    1990-07-01

    Effects were evaluated of high dietary levels of magnesium oxide (MgO) or limestone on DM, OM and CP digestibility, N balance and intestinal absorption of amino acids by lambs fed a high concentrate diet. Twelve wether lambs equipped with abomasal and ileal cannulas were blocked by weight and breeding and allotted to treatments in a randomized block design in two consecutive trials. Diets were control (800 g), control plus 1.5% MgO (812 g), control plus 1.5% limestone (812 g) and control plus 3.0% limestone (824 g) fed in two equal portions at 12-h intervals. Ruminal fluid pH differences were small. The pH of ileal digesta was greater (P less than .05) with MgO than with limestone (8.23 vs 7.73). Fecal pH was higher (P less than .01) for lambs fed all mineral treatments (avg 8.75) than for lambs fed the control (7.61) and was higher (P less than .01) when MgO (9.53) rather than limestone (8.36) was fed. Ruminal NH3N was lower (P less than .01) when lambs were fed MgO (11.9 mg/dl) compared with limestone (avg 31.2 mg/dl). Preintestinal DM digestibility was greatest (P less than .10) with limestone (avg 49.5%) feeding compared with feeding MgO (31.2%) or the control (35.4%). About 41.5% more essential (P less than .05) and 48% more nonessential (P less than .03) amino acids reached the small intestine when MgO was fed than when limestone was fed. Partial digestibility of amino acids in the small intestine was reduced (P less than .03) an average of 5 percentage units when MgO or limestone was fed. Feeding high levels of MgO or limestone to lambs did not improve the overall digestibility of DM, OM or CP. In fact, feeding high levels of MgO or limestone appeared to be detrimental, reducing intestinal absorption of amino acids.

  16. Determination of diffusion coefficients in cohesive and sandy sediment from the area of Gorleben

    International Nuclear Information System (INIS)

    Klotz, D.

    1989-01-01

    The cohesive and sandy sediments stem from shaft driving at the Gorleben salt done. For the cohesive materials, HTD was used as a tracer substance, while I-131 - was used for the sandy materials. Diffusion coefficients of HTD in cohesive materials in their natural texture are in the range of 2x10 -6 to 5x10 -6 cm 2 /s, those of I-131 - in the investigated uniform fine and middle sands are approximately 3x10 -6 cm 2 /s. (DG) [de

  17. Geochemical processes at a fresh/seawater interface in a shallow sandy aquifer

    DEFF Research Database (Denmark)

    Andersen, Martin Søgaard; Iversen, Vibeke Margrethe Nyvang; Postma, Diederik Jan

    2001-01-01

    Chemical processes in a natural fresh-/seawater mixing zone were studied in a shallow sandy aquifer. The dominant redox-processes are sulfate reduction and methanogenesis. Methanogenesis produces CO2, which causes calcite dissolution. The produced calcium induces ion exchange with sodium. The fin...... result of these interactions between different types of geochemical processes is an anoxic groundwater enriched in bicarbonate and sodium.......Chemical processes in a natural fresh-/seawater mixing zone were studied in a shallow sandy aquifer. The dominant redox-processes are sulfate reduction and methanogenesis. Methanogenesis produces CO2, which causes calcite dissolution. The produced calcium induces ion exchange with sodium. The final...

  18. Geologic framework and hydrogeologic characteristics of the Glen Rose limestone, Camp Stanley Storage Activity, Bexar County, Texas

    Science.gov (United States)

    Clark, Allan K.

    2004-01-01

    The Trinity aquifer is a regional water source in the Hill Country of south-central Texas that supplies water for agriculture, commercial, domestic, and stock purposes. Rocks of the Glen Rose Limestone, which compose the upper zone and upper part of the middle zone of the Trinity aquifer, crop out at the Camp Stanley Storage Activity (CSSA), a U.S. Army weapons and munitions supply, maintenance, and storage facility in northern Bexar County (San Antonio area) (fig. 1). On its northeastern, eastern, and southern boundaries, the CSSA abuts the Camp Bullis Training Site, a U.S. Army field training site for military and Federal government agencies. During 2003, the U.S. Geological Survey (USGS), in cooperation with the U.S. Army, studied the outcropping Glen Rose Limestone at the CSSA and immediately adjacent area (Camp Stanley study area, fig. 1) to identify and map the hydrogeologic subdivisions and faults of the Glen Rose Limestone at the facility. The results of the study are intended to help resource managers improve their understanding of the distribution of porosity and permeability of the outcropping rocks, and thus the conditions for recharge and the potential for contaminants to enter the Glen Rose Limestone. This study followed a similar study done by the USGS at Camp Bullis (Clark, 2003). The purpose of this report is to present the geologic framework and hydrogeologic characteristics of the Glen Rose Limestone in the study area. The hydrogeologic nomenclature follows that introduced by Clark (2003) for the outcropping Glen Rose Limestone at Camp Bullis in which the upper member of the Glen Rose Limestone (hereinafter, upper Glen Rose Limestone), which is coincident with the upper zone of the Trinity aquifer, is divided into five intervals on the basis of observed lithologic and hydrogeologic properties. An outcrop map, two generalized sections, related illustrations, and a table summarize the description of the framework and distribution of characteristics.

  19. Liquid carbon dioxide/pulverized limestone globulsion delivery system for deep ocean storage

    Energy Technology Data Exchange (ETDEWEB)

    Swett, P.; Golomb, D.; Barry, E.; Ryan, D.; Lawton, C. [Massachusetts Univ., Lowell, MA (United States)

    2005-07-01

    Ocean storage of carbon dioxide (CO{sub 2}) raises serious environmental, technical and economic problems because a massive point injection of pure liquid CO{sub 2} at depth would create a plume of carbonic acid with a pH lower than 7. Acidified seawater is considered to be harmful to aquatic organisms. Laboratory studies have shown that injecting a globulsion consisting of CO{sub 2}, water (H{sub 2}O) and calcium carbonate (CaCO{sub 3}) instead of pure liquid CO{sub 2} results in an alkaline reaction rather than an acidic reaction. Because calcium carbonate and bicarbonate are natural ingredients of seawater, there is no expected harm due to the additive limestone. This paper presented a practical delivery system for the underwater creation of globulsion. When liquid or supercritical CO{sub 2} is mixed with a slurry of finely pulverized limestone (CaCO{sub 3}) in pure or seawater, a macro-emulsion is formed consisting of CO{sub 2} droplets coated with CaCO{sub 3} particles dispersed in water. In this study, liquid CO{sub 2} was piped to approximately 500 m depth, which is below the flash point of liquid CO{sub 2} into vapor. A slurry of pulverized limestone in seawater was also separately piped to this depth. A static mixer was mounted at the end of the pipes. Liquid CO{sub 2}, along with a slurry of pulverized limestone and ambient seawater were pumped into the mixer by a turbine. The globulsion exited from the other end of the mixer and sank like a dense plume to greater depths while entraining ambient seawater. The CaCO{sub 3}-coated globules precipitated from the neutrally buoyant plume toward the ocean bottom following equilibration. As such, the ocean was not be acidified with this method of CO{sub 2} discharging. It was concluded that even inland seas, such as the Mediterranean and Black Seas, could be considered for sequestration of a CO{sub 2}/H{sub 2}O/CaCO{sub 3} globulsion. Although adding pulverized limestone to liquid CO{sub 2} and the mixing

  20. Petrophysical and transport parameters evolution during acid percolation through structurally different limestones

    Science.gov (United States)

    Martinez Perez, Laura; Luquot, Linda

    2017-04-01

    Processes affecting geological media often show complex and unpredictable behavior due to the presence of heterogeneities. This remains problematic when facing contaminant transport problems, in the CO2 storage industry or dealing with the mechanisms underneath natural processes where chemical reactions can be observed during the percolation of rock non-equilibrated fluid (e.g. karst formation, seawater intrusion). To understand the mechanisms taking place in a porous medium as a result of this water-rock interaction, we need to know the flow parameters that control them, and how they evolve with time as a result of that concurrence. This is fundamental to ensure realistic predictions of the behavior of natural systems in response of reactive transport processes. We investigate the coupled influence of structural and hydrodynamic heterogeneities in limestone rock samples tracking its variations during chemical reactions. To do so we use laboratory petrophysical techniques such as helium porosimetry, gas permeability, centrifugue, electrical resistivity and sonic waves measurements to obtain the parameters that characterize flow within rock matrix (porosity, permeability, retention curve and pore size distribution, electrical conductivity, formation factor, cementation index and tortuosity) before and after percolation experiments. We built an experimental setup that allows injection of acid brine into core samples under well controlled conditions, monitor changes in hydrodynamic properties and obtain the chemical composition of the injected solution at different stages. 3D rock images were also acquired before and after the experiments using a micro-CT to locate the alteration processes and perform an acurate analysis of the structural changes. Two limestones with distinct textural classification and thus contrasting transport properties have been used in the laboratory experiments: a crinoid limestone and an oolithic limestone. Core samples dimensions were 1 inch

  1. Effects of Water and Low-Medium Temperature on Limestone from Mt Etna basement

    Science.gov (United States)

    Castagna, Angela; Ougier-Simonin, Audrey; Benson, Philip; Browning, John; Fazio, Marco; Walker, Richard; Vinciguerra, Sergio

    2017-04-01

    Mount Etna volcano, Sicily, sits atop a structurally complex sedimentary basement continuously subjected to tectonic deformation. The flyschoid formations belonging to the Appenninic-Maghrebian Chain (AMC) and making up the accretionary wedge of a regional fold-and-thrust belt lie above carbonate Hyblean Plateau (HP) sequences, belonging to the African plate. Carbonate rocks represent a major component of the sedimentary basement: they are spread throughout the AMC as continuous strata and discontinuous lenses, and are the main constituent (e.g., Comiso Limestone) of the HP foreland. Etna is an active volcanic environment, characterized by complex stress field distributions, magmatic and non-magmatic fluid circulation, and elevated temperature gradients; the edifice has been constructed at various rates and with variable distribution of effusive products. These intrinsic and extrinsic parameters are known to impact the rheological behaviour of rocks. Previous triaxial deformation studies on carbonates (Tavel Limestone, Solnhofen Limestone and Comiso Limestone) have shown the importance of temperature, and the presence of water as pore fluid, on the mechanical strength and failure mode of the rocks. However, to our knowledge, no previous studies have considered the distal heating effect of intrusions on the carbonate mechanical strength from the basement. Here we investigate the behaviour under varying P-T conditions at constant strain rate (10-5 s-1) on both dry and water saturated samples of Comiso Limestone, a low-porosity (10.2% average) carbonate rock belonging to the HP. We ran separate conventional triaxial experiments at various confining effective pressure from 0 up to 50 MPa at room temperature (20°C), in both dry and drained water-saturated conditions, using natural samples, and thermally-treated samples (150°C, 300°C, and 450°C). Acoustic Emissions and P-wave velocities were recorded during the experiments. Sample failure covers the brittle and

  2. Bacterial polyextremotolerant bioemulsifiers from arid soils improve water retention capacity and humidity uptake in sandy soil

    KAUST Repository

    Raddadi, Noura; Giacomucci, Lucia; Marasco, Ramona; Daffonchio, Daniele; Cherif, Ameur; Fava, Fabio

    2018-01-01

    Water stress is a critical issue for plant growth in arid sandy soils. Here, we aimed to select bacteria producing polyextremotolerant surface-active compounds capable of improving water retention and humidity uptake in sandy soils.From Tunisian desert and saline systems, we selected eleven isolates able to highly emulsify different organic solvents. The bioemulsifying activities were stable with 30% NaCl, at 4 and 120 °C and in a pH range 4-12. Applications to a sandy soil of the partially purified surface-active compounds improved soil water retention up to 314.3% compared to untreated soil. Similarly, after 36 h of incubation, the humidity uptake rate of treated sandy soil was up to 607.7% higher than untreated controls.Overall, results revealed that polyextremotolerant bioemulsifiers of bacteria from arid and desert soils represent potential sources to develop new natural soil-wetting agents for improving water retention in arid soils.

  3. Enhancing crude oil degradation in a sandy soil: Effects of addition ...

    African Journals Online (AJOL)

    This study investigated the effects of the addition of poultry manure alone and in combination with surfactant (Goldcrew or Corexit) and/or alternate carbon substrate (glucose or starch) on crude oil degradation in a sandy soil. With poultry manure alone, optimal crude oil degradation was obtained at a concentration of 4.0% ...

  4. Improvement of Water Movement in an Undulating Sandy Soil Prone to Water Repellency

    NARCIS (Netherlands)

    Oostindie, K.; Dekker, L.W.; Wesseling, J.G.; Ritsema, C.J.

    2011-01-01

    The temporal dynamics of water repellency in soils strongly influence water flow. We investigated the variability of soil water content in a slight slope on a sandy fairway exhibiting water-repellent behavior. A time domain reflectometry (TDR) array of 60 probes measured water contents at 3-h

  5. Transport of water and solutes in wettable and water repellent sandy soils

    NARCIS (Netherlands)

    Ritsema, C.J.; Dekker, L.W.

    1996-01-01

    The research yielded the following conclusions and results: preferential flow can be expected in recently deposited, loosely packed, wettable dune sands; preferential flow is common in most water-repellent sandy soils; distribution flow in topsoils isa process of major importance, resulting in a

  6. influence of tillage practices on physical properties of a sandy loam

    African Journals Online (AJOL)

    DR. AMINU

    many regions of the world if the mechanics of tillage effects on soil physical properties is to be well understood. Thus, the ... tillage systems on water storage of a sandy loam soil after 22 years of ..... Soil infiltration ... and processes. Academy ...

  7. Limits to intensity of milk production in sandy areas in The Netherlands

    NARCIS (Netherlands)

    Aarts, H.F.M.; Habekotté, B.; Keulen, van H.

    1999-01-01

    Agricultural land in sandy areas is mainly in use by dairy farms. As a result of intensive fertilisation and irrigation, environmental quality is threatened by lost nutrients and lowered groundwater levels. Therefore, Dutch government put decreasing limits to losses of nutrients, with lowest values

  8. An analysis of the synoptic and dynamical characteristics of hurricane Sandy (2012)

    Science.gov (United States)

    Varlas, George; Papadopoulos, Anastasios; Katsafados, Petros

    2018-01-01

    Hurricane Sandy affected the Caribbean Islands and the Northeastern United States in October 2012 and caused 233 fatalities, severe rainfalls, floods, electricity blackouts, and 75 billion U.S. dollars in damages. In this study, the synoptic and dynamical characteristics that led to the formation of the hurricane are investigated. The system was driven by the interaction between the polar jet displacement and the subtropical jet stream. In particular, Sandy was initially formed as a tropical depression system over the Caribbean Sea and the unusually warm sea drove its intensification. The interaction between a rapidly approaching trough from the northwest and the stagnant ridge over the Atlantic Ocean drove Sandy to the northeast coast of United States. To better understand the dynamical characteristics and the mechanisms that triggered Sandy, a non-hydrostatic mesoscale model has been used. Model results indicate that the surface heat fluxes and the moisture advection enhanced the convective available potential energy, increased the low-level convective instability, and finally deepened the hurricane. Moreover, the upper air conditions triggered the low-level frontogenesis and increased the asymmetry of the system which finally affected its trajectory.

  9. Effect of soil pH on sorption of salinomycin in clay and sandy soils

    African Journals Online (AJOL)

    use

    The sorption of salinomycin to the sandy soil marginally increased as the pH decreased, while the sorption to the two .... plastic containers at room temperature for further analysis. ... The pH was adjusted eight times over 20 days to stabilize at.

  10. Bacterial polyextremotolerant bioemulsifiers from arid soils improve water retention capacity and humidity uptake in sandy soil.

    Science.gov (United States)

    Raddadi, Noura; Giacomucci, Lucia; Marasco, Ramona; Daffonchio, Daniele; Cherif, Ameur; Fava, Fabio

    2018-05-31

    Water stress is a critical issue for plant growth in arid sandy soils. Here, we aimed to select bacteria producing polyextremotolerant surface-active compounds capable of improving water retention and humidity uptake in sandy soils. From Tunisian desert and saline systems, we selected eleven isolates able to highly emulsify different organic solvents. The bioemulsifying activities were stable with 30% NaCl, at 4 and 120 °C and in a pH range 4-12. Applications to a sandy soil of the partially purified surface-active compounds improved soil water retention up to 314.3% compared to untreated soil. Similarly, after 36 h of incubation, the humidity uptake rate of treated sandy soil was up to 607.7% higher than untreated controls. Overall, results revealed that polyextremotolerant bioemulsifiers of bacteria from arid and desert soils represent potential sources to develop new natural soil-wetting agents for improving water retention in arid soils.

  11. Bacterial polyextremotolerant bioemulsifiers from arid soils improve water retention capacity and humidity uptake in sandy soil

    KAUST Repository

    Raddadi, Noura

    2018-05-31

    Water stress is a critical issue for plant growth in arid sandy soils. Here, we aimed to select bacteria producing polyextremotolerant surface-active compounds capable of improving water retention and humidity uptake in sandy soils.From Tunisian desert and saline systems, we selected eleven isolates able to highly emulsify different organic solvents. The bioemulsifying activities were stable with 30% NaCl, at 4 and 120 °C and in a pH range 4-12. Applications to a sandy soil of the partially purified surface-active compounds improved soil water retention up to 314.3% compared to untreated soil. Similarly, after 36 h of incubation, the humidity uptake rate of treated sandy soil was up to 607.7% higher than untreated controls.Overall, results revealed that polyextremotolerant bioemulsifiers of bacteria from arid and desert soils represent potential sources to develop new natural soil-wetting agents for improving water retention in arid soils.

  12. Efficacy of exclosures in conserving local shrub biodiversity in xeric sandy grassland, Inner Mongolia, China

    Science.gov (United States)

    Feng-Rui Li; Zhi-Yu Zhou; Li-Ya Zhao; Ai-Sheng Zhang; Ling-Fen Kang

    2007-01-01

    This study investigated the abundance and frequency of occurrence of all shrub species present in the standing vegetation at four sites, including a 5-year exclosure (protected grassland) and three adjacent unprotected grazing sites that had been subjected to different levels of degradation (light, moderate and severe), in xeric sandy grassland of Inner Mongolia for...

  13. Assessment of structural stability of a degraded sandy clay loam soil ...

    African Journals Online (AJOL)

    The effects of bare, two legumes and four grasses cover treatments on the structural stability of a sandy clay loam Ultisol were studied within a two year period. The experiment was of a randomised complete block design with seven treatments. The legume treatments were Centrosema pubescens (Ce) and Pueraria ...

  14. Sensitivity analysis of the surface water- groundwater interaction for the sandy area of the Netherlands

    NARCIS (Netherlands)

    Gomez del Campo, E.; Jousma, G.; Massop, H.T.L.

    1993-01-01

    The "Sensitivity Analysis of the Surface Water- Groundwater Interaction for the Sandy Area of the Netherlands" was carried out in the framework of a bilateral research project in support of the implementation of a nationwide geohydrological information system (REGIS) in the Netherlands. This

  15. 2012 USACE Post Sandy Topographic LiDAR: Virginia and Maryland

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — TASK ORDER NAME: VIRGINIA AND MARYLAND LIDAR ACQUISITION FOR SANDY RESPONSE CONTRACT NUMBER: W912P9-10-D-0533 TASK ORDER NUMBER: W81C8X2314841 Woolpert Project...

  16. 2012 USACE Post Sandy Topographic LiDAR: Eastern Long Island, New York

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — TASK ORDER NAME: EASTERN LONG ISLAND, NEW YORK LIDAR ACQUISITION FOR SANDY RESPONSE CONTRACT NUMBER: W912P9-10-D-0533 TASK ORDER NUMBER: W81C8X23208588 Woolpert...

  17. Amelioration of sandy soils in drought stricken areas through use of ...

    African Journals Online (AJOL)

    Soil moisture shortage is a major limiting factor to agricultural production in eastern Africa, in view of increased drought incidences and seasonal rainfall variability. This study evaluated the potential for Ca-bentonite (a 2:1 clay mineral) as a possible amendment for increased moisture retention by sandy soils in drought ...

  18. Fine natural aggregate replacement for sandy residue from itabirite exploitation in Portland cement mortar

    International Nuclear Information System (INIS)

    Melo, V.A.R.; Freire, C.B.; Pereira Junior, S.S.; Lameiras, F.S.; Tello, C.C.O.

    2011-01-01

    The fine natural aggregates are a material largely used by the civil construction for mortar and concrete production. Due to tightening legal restrictions imposed on their extraction, alternative materials are being considered. The use of sandy residue from BIF (banded iron formations) exploitation was investigated. It requires their grinding and flotation to concentrate iron oxides. Large amounts of sandy residue composed of quartz and iron oxides are generated in this process. The sandy residue was characterized relative to mineralogical composition, particle size distribution, presence of organic impurities, and particle shape. Mortar formulations were prepared by varying the type of cement, the cement to aggregate proportion and the water/cement ratio (a/c). The results of viscosity and density of fresh mortar, setting time, and compressive strength are presented. Compressive strength up to 19.5 MPa at 28 days were achieved with the use of cement CPV, a/c ratio of 0.80 and cement:aggregate proportion of 1:2. The results demonstrate the technical feasibility of using sandy residue as fine aggregate. (author)

  19. A new method for measuring bioturbation rates in sandy tidal flat sediments based on luminescence dating

    DEFF Research Database (Denmark)

    Madsen, Anni T.; Murray, Andrew S.; Jain, Mayank

    2011-01-01

    The rates of post-depositional mixing by bioturbation have been investigated using Optically Stimulated Luminescence (OSL) dating in two sediment cores (BAL2 and BAL5), retrieved from a sandy tidal flat in the Danish part of the Wadden Sea. A high-resolution chronology, consisting of thirty-six OSL...

  20. Storm Impact and Depression Among Older Adults Living in Hurricane Sandy-Affected Areas.

    Science.gov (United States)

    Sirey, Jo Anne; Berman, Jacquelin; Halkett, Ashley; Giunta, Nancy; Kerrigan, Janice; Raeifar, Elmira; Artis, Amanda; Banerjee, Samprit; Raue, Patrick J

    2017-02-01

    Research on the impact of natural disasters on the mental health of older adults finds both vulnerabilities and resilience. We report on the rates of clinically significant depression among older adults (aged ≥60 years) living in areas affected by Hurricane Sandy in 2012 and the factors associated with mental health need. The Sandy Mobilization, Assessment, Referral and Treatment for Mental Health (SMART-MH) program integrates community outreach and needs assessments to identify older adults with mental health and aging service needs. Older adults with significant anxiety or depressive symptoms were offered short-term psychotherapy. Social service referrals were made directly to community agencies. All SMART-MH activities were offered in Spanish, Russian, Mandarin/Cantonese, and English. Across the full sample, 14% of participants screened positive for depression. Hurricane Sandy stressors predicted increased odds of depression, including storm injury, post-storm crime, and the total count of stressors. Outcomes varied significantly by age group, such that all Sandy-related variables remained significant for younger-old adults (aged 60-74 years), whereas only the loss of access to medical care was significant for older-old adults (aged ≥75 years). Storm-affected communities show higher rates of depressive symptoms than seen in the general population, with storm stressors affecting mental health needs differentially by age group. (Disaster Med Public Health Preparedness. 2017;11:97-109).

  1. Toward a Unified Military Response: Hurricane Sandy and the Dual Status Commander

    Science.gov (United States)

    2015-04-01

    18th tropical depression of the season formed over the southwestern Caribbean Sea and quickly strength- ened into Tropical Storm Sandy late that... Centennial , a combined Title 10 and 32 operation, during the Sep- tember 2013 response to the Colorado Floods. 117 APPENDIX I ACRONYMS AAR After Action

  2. Symposium of Hope: Recovery and Resiliency after the Sandy Hook Tragedy. Crisis Management

    Science.gov (United States)

    Zenere, Frank J.

    2013-01-01

    On February 27 and 28, 2013, The Symposium of Hope: Recovery and Resilience after the Sandy Hook Tragedy, was held in Danbury, Connecticut. The event was hosted by the United Way of Western Connecticut and Western Connecticut State University. Frank J. Zenere, school psychologist and crisis team member in the Division of Student Services of the…

  3. Groundwater chemistry of Al under Dutch sandy soils: Effects of land use and depth

    NARCIS (Netherlands)

    Fest, E.P.M.J.; Temminghoff, E.J.M.; Griffioen, J.; Grift, B. van der; Riemsdijk, W.H. van

    2007-01-01

    Aluminium has received great attention in the second half of the 20th century, mainly in the context of the acid rain problem mostly in forest soils. In this research the effect of land use and depth of the groundwater on Al, pH and DOC concentration in groundwater under Dutch sandy soils has been

  4. Enhanced benthic activity in sandy sublittoral sediments: Evidence from 13C tracer experiments

    NARCIS (Netherlands)

    Bühring, S.I.; Ehrenhauss, S.; Kamp, A.; Moodley, L.; Prof. Witte, U.

    2006-01-01

    In situ and on-board pulse-chase experiments were carried out on a sublittoral fine sand in the German Bight (southern North Sea) to investigate the hypothesis that sandy sediments are highly active and have fast turnover rates. To test this hypothesis, we conducted a series of experiments where we

  5. Use of dolomite phosphate rock (DPR) fertilizers to reduce phosphorus leaching from sandy soil

    International Nuclear Information System (INIS)

    Chen, G.C.; He, Z.L.; Stoffella, P.J.; Yang, X.E.; Yu, S.; Calvert, D.

    2006-01-01

    There is increasing concern over P leaching from sandy soils applied with water-soluble P fertilizers. Laboratory column leaching experiments were conducted to evaluate P leaching from a typical acidic sandy soil in Florida amended with DPR fertilizers developed from dolomite phosphate rock (DPR) and N-Viro soil. Ten leaching events were carried out at an interval of 7 days, with a total leaching volume of 1183 mm equivalent to the mean annual rainfall of this region during the period of 2001-2003. Leachates were collected and analyzed for total P and inorganic P. Phosphorus in the leachate was dominantly reactive, accounting for 67.7-99.9% of total P leached. Phosphorus leaching loss mainly occurred in the first three leaching events, accounting for 62.0-98.8% of the total P leached over the whole period. The percentage of P leached (in the total P added) from the soil amended with water-soluble P fertilizer was higher than those receiving the DPR fertilizers. The former was up to 96.6%, whereas the latter ranged from 0.3% to 3.8%. These results indicate that the use of N-Viro-based DPR fertilizers can reduce P leaching from sandy soils. - Fertilizers developed from dolomite phosphate rock (DPR) reduce phosphorus leaching from sandy soil

  6. Importance of phytodetritus and microphytobenthos for heterotrophs in a shallow subtidal sandy sediment

    NARCIS (Netherlands)

    Evrard, V.; Huettel, M.; Cook, P.L.M.; Soetaert, K.; Heip, C.H.R.; Middelburg, J.J.

    2012-01-01

    The relative importance of allochthonous phytodetritus deposition and autochthonous microphytobenthos (MPB) production for benthic consumers in an organic carbon (C-org)-poor sandy sediment was assessed using a C-13-stable isotope natural abundance study combined with a dual C-13-tracer addition

  7. Carbon and nitrogen flows through the benthic food web of a photic subtidal sandy sediment

    NARCIS (Netherlands)

    Evrard, V.P.E.; Soetaert, K.E.R.; Heip, C.H.R.; Huettel, M.; Xenopoulos, M.A.; Middelburg, J.J.

    2010-01-01

    Carbon and nitrogen flows within the food web of a subtidal sandy sediment were studied using stable isotope natural abundances and tracer addition. Natural abundances of 13C and 15N stable isotopes of the consumers and their potential benthic and pelagic resources were measured. δ13C data revealed

  8. Effect of Particle Size and Soil Compaction on Gas Transport Parameters in Variably Saturated, Sandy Soils

    DEFF Research Database (Denmark)

    Hamamoto, Shoichiro; Møldrup, Per; Kawamoto, Ken

    2009-01-01

    The soil gas diffusion coefficient (Dp) and air permeability (ka) and their dependency on soil air content ( ) control gas diffusion and advection in soils. This study investigated the effects of average particle size (D50) and dry bulk density ( b) on Dp and ka for six sandy soils under variably...

  9. Irrigation initiation timing in soybean grown on sandy soils in Northeast Arkansas

    Science.gov (United States)

    Irrigation initiation timing was evaluated in furrow-irrigated soybean field with sandy soils in Mississippi County, AR. A major objective of this 2015 study was to validate and expand irrigation timing recommendations that pair plant growth measures with weather cues including use of local weather ...

  10. The Sandy Hook Elementary School shooting as tipping point: "This Time Is Different".

    Science.gov (United States)

    Shultz, James M; Muschert, Glenn W; Dingwall, Alison; Cohen, Alyssa M

    2013-01-01

    Among rampage shooting massacres, the Sandy Hook Elementary School shooting on December 14, 2012 galvanized public attention. In this Commentary we examine the features of this episode of gun violence that has sparked strong reactions and energized discourse that may ultimately lead toward constructive solutions to diminish high rates of firearm deaths and injuries in the United States.

  11. Lessons from Hurricane Sandy: a community response in Brooklyn, New York.

    Science.gov (United States)

    Schmeltz, Michael T; González, Sonia K; Fuentes, Liza; Kwan, Amy; Ortega-Williams, Anna; Cowan, Lisa Pilar

    2013-10-01

    The frequency and intensity of extreme weather events have increased in recent decades; one example is Hurricane Sandy. If the frequency and severity continue or increase, adaptation and mitigation efforts are needed to protect vulnerable populations and improve daily life under changed weather conditions. This field report examines the devastation due to Hurricane Sandy experienced in Red Hook, Brooklyn, New York, a neighborhood consisting of geographically isolated low-lying commercial and residential units, with a concentration of low-income housing, and disproportionate rates of poverty and poor health outcomes largely experienced by Black and Latino residents. Multiple sources of data were reviewed, including street canvasses, governmental reports, community flyers, and meeting transcripts, as well as firsthand observations by a local nonprofit Red Hook Initiative (RHI) and community members, and social media accounts of the effects of Sandy and the response to daily needs. These data are considered within existing theory, evidence, and practice on protecting public health during extreme weather events. Firsthand observations show that a community-based organization in Red Hook, RHI, was at the center of the response to disaster relief, despite the lack of staff training in response to events such as Hurricane Sandy. Review of these data underscores that adaptation and response to climate change and likely resultant extreme weather is a dynamic process requiring an official coordinated governmental response along with on-the-ground volunteer community responders.

  12. Development and Application of Syndromic Surveillance for Severe Weather Events Following Hurricane Sandy.

    Science.gov (United States)

    Tsai, Stella; Hamby, Teresa; Chu, Alvin; Gleason, Jessie A; Goodrow, Gabrielle M; Gu, Hui; Lifshitz, Edward; Fagliano, Jerald A

    2016-06-01

    Following Hurricane Superstorm Sandy, the New Jersey Department of Health (NJDOH) developed indicators to enhance syndromic surveillance for extreme weather events in EpiCenter, an online system that collects and analyzes real-time chief complaint emergency department (ED) data and classifies each visit by indicator or syndrome. These severe weather indicators were finalized by using 2 steps: (1) key word inclusion by review of chief complaints from cases where diagnostic codes met selection criteria and (2) key word exclusion by evaluating cases with key words of interest that lacked selected diagnostic codes. Graphs compared 1-month, 3-month, and 1-year periods of 8 Hurricane Sandy-related severe weather event indicators against the same period in the following year. Spikes in overall ED visits were observed immediately after the hurricane for carbon monoxide (CO) poisoning, the 3 disrupted outpatient medical care indicators, asthma, and methadone-related substance use. Zip code level scan statistics indicated clusters of CO poisoning and increased medicine refill needs during the 2 weeks after Hurricane Sandy. CO poisoning clusters were identified in areas with power outages of 4 days or longer. This endeavor gave the NJDOH a clearer picture of the effects of Hurricane Sandy and yielded valuable state preparation information to monitor the effects of future severe weather events. (Disaster Med Public Health Preparedness. 2016;10:463-471).

  13. Weathering the Superstorm: From Texts to Twitter--How Campus Communicators Overcame Hurricane Sandy

    Science.gov (United States)

    Towns, Gail

    2013-01-01

    By the time Superstorm Sandy struck New Jersey in late October 2012, Kathy Corbalis, executive director of communications and college relations at Atlantic Cape Community College, and her team were battle-tested. In the 15 months before the hurricane, the college experienced two bomb threats via Twitter, a lockdown due to gunfire, an on-campus…

  14. Vegetation impact on the hydrology of an aeolian sandy soil in a continental climate

    Czech Academy of Sciences Publication Activity Database

    Lichner, Ľ.; Hallett, P. D.; Orfánus, T.; Czachor, H.; Rajkai, K.; Šír, Miloslav; Tesař, Miroslav

    2010-01-01

    Roč. 3, č. 4 (2010), s. 413-420 ISSN 1936-0584 R&D Projects: GA MŠk MEB0808114 Institutional research plan: CEZ:AV0Z20600510 Keywords : sandy soil * water repellency * plant cover * sorptivity * hydraulic conductivity Subject RIV: DA - Hydrology ; Limnology Impact factor: 1.835, year: 2010

  15. Modelling dune erosion, overwash and breaching at Fire Island (NY) during hurricane Sandy

    NARCIS (Netherlands)

    De Vet, P.L.M.; McCall, R.T.; Den Bieman, J.P.; Stive, M.J.F.; Van Ormondt, M.

    2015-01-01

    In 2012, Hurricane Sandy caused a breach at Fire Island (NY, USA), near Pelican Island. This paper aims at modelling dune erosion, overwash and breaching processes that occured during the hurricane event at this stretch of coast with the numerical model XBeach. By using the default settings, the

  16. TOXICITY TRENDS DURING AN OIL SPILL BIOREMEDIATION EXPERIMENT ON A SANDY SHORELINE IN DELAWARE, USA

    Science.gov (United States)

    A 13-week, refereed, inter-agency toxicity testing program involving five bioassay methods was used to document the effectiveness of shoreline bioremediation to accelerate toxicity reduction of an oiled sandy shoreline at Fowler Beach, Delaware, USA. The study was part of an inte...

  17. Factors affecting N immobilisation/mineralisation kinetics for cellulose-, glucose- and straw-amended sandy soils

    NARCIS (Netherlands)

    Vinten, A.J.A.; Whitmore, A.P.; Bloem, J.; Howard, R.; Wright, F.

    2002-01-01

    The kinetics of nitrogen immobilization/mineralization for cellulose-, glucose- and straw-amended sandy soils were investigated in a series of laboratory incubations. Three Scottish soils expected to exhibit a range of biological activity were used: aloamy sand, intensively cropped horticultural

  18. Pore structure characteristics after two years biochar application to a sandy loam field

    DEFF Research Database (Denmark)

    Sun, Zhencai; Arthur, Emmanuel; de Jonge, Lis Wollesen

    2015-01-01

    the effects of birch wood biochar (20, 40, and 100 Mg ha−1) applied to a sandy loam on soil total porosity and pore structure indices. Bulk and intact soil samples were collected for physicochemical analyses and water retention and gas diffusivity measurements between pF 1.0 and pF 3.0. Biochar application...

  19. Enhancing the biodegradation of oil in sandy sediments with choline: A naturally methylated nitrogen compound

    International Nuclear Information System (INIS)

    Mortazavi, Behzad; Horel, Agota; Anders, Jennifer S.; Mirjafari, Arsalan; Beazley, Melanie J.; Sobecky, Patricia A.

    2013-01-01

    We investigated how additions of choline, a naturally occurring methylated nitrogen-containing compound, accelerated hydrocarbon degradation in sandy sediments contaminated with moderately weathered crude oil (4000 mg kg −1 sediment). Addition of lauroylcholine chloride (LCC) and tricholine citrate (TCC) to oil contaminated sediments resulted in 1.6 times higher hydrocarbon degradation rates compared to treatments without added choline derivatives. However, the degradation rate constant for the oil contaminated sediments amended with LCC was similar to that in contaminated sediments amended with inorganic nitrogen, phosphorus, and glucose. Additions of LLC and TCC to sediments containing extensively weathered oil also resulted in enhanced mineralization rates. Cultivation-free 16S rRNA analysis revealed the presence of an extant microbial community with clones closely related to known hydrocarbon degraders from the Gammaproteobacteria, Alphaproteobacteria, and Firmicutes phyla. The results demonstrate that the addition of minimal amounts of organic compounds to oil contaminated sediments enhances the degradation of hydrocarbons. -- Highlights: •Aerobic degradation of weathered crude oil in sandy sediments was determined. •The effect of input of choline on degradation rates was determined. •16S rRNA clone library analyses were used to examine the microbial phylogeny. •The bacterial community was consisted of clones related to hydrocarbon degraders. •Hydrocarbon degradation in sandy sediments was accelerated by addition of choline. -- Choline, a naturally occurring methylated nitrogen-containing compound, accelerated hydrocarbon degradation in sandy sediments by an extant microbial community

  20. Patterns of Arbuscular Mycorrhizal Fungal Distribution on Mainland and Island Sandy Coastal Plain Ecosystems in Brazil.

    Science.gov (United States)

    da Silva, Iolanda Ramalho; de Souza, Francisco Adriano; da Silva, Danielle Karla Alves; Oehl, Fritz; Maia, Leonor Costa

    2017-10-01

    Although sandy coastal plains are important buffer zones to protect the coast line and maintain biological diversity and ecosystem services, these ecosystems have been endangered by anthropogenic activities. Thus, information on coastal biodiversity and forces shaping coastal biological diversity are extremely important for effective conservation strategies. In this study, we aimed to compare arbuscular mycorrhizal (AM) fungal communities from soil samples collected on the mainland and nearby islands located in Brazilian sandy coastal plain ecosystems (Restingas) to get information about AM fungal biogeography and identify factors shaping these communities. Soil samples were collected in 2013 and 2014 on the beachfront of the tropical sandy coastal plain at six sites (three island and three mainland locations) across the northeast, southeast, and south regions of Brazil. Overall, we recorded 53 AM fungal species from field and trap culture samples. The richness and diversity of AM fungal species did not differ between mainland and island locations, but AM fungal community assemblages were different between mainland and island environments and among most sites sampled. Glomeromycota communities registered from island samples showed higher heterogeneity than communities from mainland samples. Sandy coastal plains harbor diverse AM fungal communities structured by climatic, edaphic, and spatial factors, while the distance from the colonizing source (mainland environments) does not strongly affect the AM fungal communities in Brazilian coastal environments.

  1. CONTRIBUTIONS TO IMPROVING CULTURE TEHNOLOGIES OF PEACHES GROWN ON SANDY SOILS THE SOUTH OF OLTENIA

    Directory of Open Access Journals (Sweden)

    Anica Durau

    2013-12-01

    Full Text Available Technological factors with major implications in obtaining high yields and quality in peaches grown on sandy soils are planting row distance and shape of the crown, soil maintenance system, chemical, organic and foliar fertilzation. A smal size combined with the flatening of the crowns of the tres alows a dense planting, also ensure proper mechanization of work and easy penetration of light to the leaves and fruits. Crown form vertical belt proved to be suitable for al planting distances studied, easily made and maintained, having fruit production ranged betwen 15.9 t / ha at a distance of 2 m, 10.3 t / ha at a distance of 2.5 m and 7.9 t / ha at a distance of 3 m. The state of soil nutrient supply influence sucesful peach crop on sandy soils. The fertilzer dose of technology to N10 P80 K10 kg s.a / ha production was 34.9 t / ha. Organic fertilzation also contributes to obtaining high yields of peach. In sandy soil conditions most fruit production of 9.6 t / ha was obtained by fertilzation with organic manure 60t/ha. Besides fertilzation, soil maintenance system is one important link in the technology peach crop on sandy soils. The results found that the biggest peach fruit production was obtained from field maintenance system black-8,2t/ha. Using technology in foliar peaches culture on sandy soils, is an important means of providing nutrients that lead to improved proceses of growth and fructification. The best way is with foliar fertilzation Folibor in dose 5l/ha, the production obtained was 12.4 t /ha.

  2. Telehealth at the US Department of Veterans Affairs after Hurricane Sandy.

    Science.gov (United States)

    Der-Martirosian, Claudia; Griffin, Anne R; Chu, Karen; Dobalian, Aram

    2018-01-01

    Background Like other integrated health systems, the US Department of Veterans Affairs has widely implemented telehealth during the past decade to improve access to care for its patient population. During major crises, the US Department of Veterans Affairs has the potential to transition healthcare delivery from traditional care to telecare. This paper identifies the types of Veterans Affairs telehealth services used during Hurricane Sandy (2012), and examines the patient characteristics of those users. Methods This study conducted both quantitative and qualitative analyses. Veterans Affairs administrative and clinical data files were used to illustrate the use of telehealth services 12 months pre- and 12 months post- Hurricane Sandy. In-person interviews with 31 key informants at the Manhattan Veterans Affairs Medical Center three-months post- Hurricane Sandy were used to identify major themes related to telecare. Results During the seven-month period of hospital closure at the Manhattan Veterans Affairs Medical Center after Hurricane Sandy, in-person patient visits decreased dramatically while telehealth visits increased substantially, suggesting that telecare was used in lieu of in-person care for some vulnerable patients. The most commonly used types of Veterans Affairs telehealth services included primary care, triage, mental health, home health, and ancillary services. Using qualitative analyses, three themes emerged from the interviews regarding the use of Veterans Affairs telecare post- Hurricane Sandy: patient safety, provision of telecare, and patient outreach. Conclusion Telehealth offers the potential to improve post-disaster access to and coordination of care. More information is needed to better understand how telehealth can change the processes and outcomes during disasters. Future studies should also evaluate key elements, such as adequate resources, regulatory and technology issues, workflow integration, provider resistance, diagnostic fidelity and

  3. Mineralogical and Micro-fabric investigation of the Sandy Facies of Opalinus Clay (Mont Terri)

    International Nuclear Information System (INIS)

    Kaufhold, Annette; Siegesmund, Siegfried; Dohrmann, Reiner; Graesle, Werner; Plischke, Ingo

    2013-01-01

    In the field of geological disposal of radioactive waste in many countries argillaceous formations are considered as potential host rock. For the understanding of the long-term behaviour of clay host rock, it is important to understand the interaction between mechanical behaviour, micro-fabric, and mineral composition. Previous publications showed that particularly the carbonate content and the arrangement of the carbonate grains (as cement in the matrix or as shells) determines the mechanical strength of Opalinus Clay and Callovo-Oxfordian Clay specimens, respectively. Klinkenberg et al. (2009) studied the shaly facies of Opalinus Clay, however, the actual deposit is planned to be built in the sandy facies of Opalinus Clay. The aim of the present study is to investigate the relation between micro-fabric, mineral composition, and mechanical properties of different samples derived from the sandy facies (BLT-A2). Image analysis showed that the carbonates in the sandy facies mainly occur as 1) matrix which in turn acts as cement. Carbonates also occur 2) in the fine sand fraction and 3) biogenic carbonates as traces. The carbonates of the sandy facies, therefore, appear to be similar to the carbonates of the Callovo-Oxfordian Clay with respect to their possible influence on failure strength. The mechanical testing showed that the shear strength increases with increasing carbonate content. This phenomenon was also observed for the samples of the Callovo-Oxfordian Clay, while the opposite relation was found for the shaly facies of the Opalinus Clay. Preliminary results presented here, indicate that the sandy facies (drilling BLT-A2) and Callovo-Oxfordian Clay show similar mechanical properties - in detail: 1) Micro-fabric: carbonates predominate in the matrix, 2) Mineralogy: high carbonate content and 3) Mechanical testing: shear strength increases with increasing carbonate content, where the type of carbonates which controls the increase of strength has to be

  4. Influence of humic substances on electrochemical degradation of trichloroethylene in limestone aquifers

    International Nuclear Information System (INIS)

    Rajic, Ljiljana; Fallahpour, Noushin; Nazari, Roya; Alshawabkeh, Akram N.

    2015-01-01

    Highlights: • Humic substances (HS) adversely affect TCE electrochemical reduction. • The inverse correlation between HS content and TCE removal is linear. • HS interfere with the hydrodechlorination of TCE at the cathode. • The impact of HS on TCE removal was reduced in the presence of limestone gravel. - Abstract: In this study we investigate the influence of humic substances (HS) on electrochemical transformation of trichloroethylene (TCE) in groundwater from limestone aquifers. A laboratory flow-through column with an electrochemical reactor that consists of a palladized iron foam cathode followed by a MMO anode was used to induce TCE electro-reduction in groundwater. Up to 82.9% TCE removal was achieved in the absence of HS. Presence of 1, 2, 5, and 10 mgTOC L −1 reduced TCE removal to 70.9%, 61.4%, 51.8% and 19.5%, respectively. The inverse correlation between HS content and TCE removal was linear. Total organic carbon (TOC), dissolved organic carbon (DOC) and absorption properties (A = 254 nm, 365 nm and 436 nm) normalized to DOC, were monitored during treatment to understand the behavior and impacts of HS under electrochemical processes. Changes in all parameters occurred mainly after contact with the cathode, which implies that the HS are reacting either directly with electrons from the cathode or with H 2 formed at the cathode surface. Since hydrodechlorination is the primary TCE reduction mechanism in this setup, reactions of the HS with the cathode limit transformation of TCE. The presence of limestone gravel reduced the impact of HS on TCE removal. The study concludes that presence of humic substances adversely affects TCE removal from contaminated groundwater by electrochemical reduction using palladized cathodes.

  5. Incorporating full-scale experience into advanced limestone wet FGD designs

    International Nuclear Information System (INIS)

    Rader, P.C.; Bakke, E.

    1992-01-01

    Utilities choosing flue gas desulfurization as a strategy for compliance with Phase I of the 1990 Clean Air Act Amendments will largely turn to limestone wet scrubbing as the most cost-effective, least-risk option. State-of-the-art single absorber wet scrubbing systems can be designed to achieve: SO 2 removal efficiencies in excess of 95 %, system availabilities in excess of 98%, and byproducts which can be marketed or land filled. As a result of varying fuel characteristics, site considerations, and owner preferences, FGD plants for large central power stations are typically custom-designed. To avoid the risks associated with new, first-of-a-kind technologies, utilities have preferred to purchase FGD systems from suppliers with proven utility experience and reference plants as close as possible to the design envisioned. As the market for FGD systems is regulatory driven, the demand has shifted geographically in response to national environmental policies. Although limestone wet scrubbing has emerged as the overwhelming choice for SO 2 emission control in coal-fired power stations, the technology has evolved and been adapted to suit local and regional technical and economic situations. Global suppliers are able to benefit from experience and technological advances in the world market. With market units in the U.S., Denmark, Italy, Sweden, and Germany active in the design and supply of wet FGD plants, ABB has a unique ability to incorporate knowledge and experience gained throughout the industrialized world to acid rain retrofit projects in the U.S. This paper describes the design of advanced limestone wet scrubbing systems for application to acid rain retrofits. Specifically, the evolution of advanced design concepts from a global experience base is discussed

  6. Soluble salt sources in medieval porous limestone sculptures: A multi-isotope (N, O, S) approach

    Energy Technology Data Exchange (ETDEWEB)

    Kloppmann, W., E-mail: w.kloppmann@brgm.fr [BRGM, Direction des Laboratoires, Unité Isotopes, BP 6009, F-45060 Orléans cedex 2 (France); Rolland, O., E-mail: olivierrolland@wanadoo.fr [Montlouis-sur-Loire (France); Proust, E.; Montech, A.T. [BRGM, Direction des Laboratoires, Unité Isotopes, BP 6009, F-45060 Orléans cedex 2 (France)

    2014-02-01

    The sources and mechanisms of soluble salt uptake by porous limestone and the associated degradation patterns were investigated for the life-sized 15th century “entombment of Christ” sculpture group located in Pont-à-Mousson, France, using a multi-isotope approach on sulphates (δ{sup 34}S and δ{sup 18}O) and nitrates (δ{sup 15}N and δ{sup 18}O). The sculpture group, near the border of the Moselle River, is within the potential reach of capillary rise from the alluvial aquifer. Chemical analyses show a vertical zonation of soluble salts with a predominance of sulphates in the lower parts of the statues where crumbling and blistering prevail, and higher concentrations of nitrates and chloride in the high parts affected by powdering and efflorescence. Isotope fingerprints of sulphates suggest a triple origin: (1) the lower parts are dominated by capillary rise of dissolved sulphate from the Moselle water with characteristic Keuper evaporite signatures that progressively decreases with height; (2) in the higher parts affected by powdering the impact of atmospheric sulphur becomes detectable; and (3) locally, plaster reparations impact the neighbouring limestone through dissolution and re-precipitation of gypsum. Nitrogen and oxygen isotopes suggest an organic origin of nitrates in all samples. N isotope signatures are compatible with those measured in the alluvial aquifer of the Moselle River further downstream. This indicates contamination by sewage or organic fertilisers. Significant isotopic contrasts are observed between the different degradation features depending on the height and suggest historical changes of nitrate sources. - Highlights: • We use S, N and O isotopes to distinguish salt sources in limestone sculptures. • Vertical zonation of degradation is linked to capillary rise and air pollution. • Sulphate salts in lower parts are derived from river/groundwater. • Sulphate salts in higher parts show signature of air pollution. • Nitrates

  7. Evaluating macroinvertebrate community shifts in the confluence of freestone and limestone streams

    Directory of Open Access Journals (Sweden)

    Jennifer K. Hellmann

    2014-07-01

    Full Text Available Aquatic macroinvertebrates are critical to ecosystem functioning through their regulation of many essential top-down and bottom-up ecosystem processes such as energy translocation, nutrient flow, and detrital decomposition. However, specific preferences by macroinvertebrates for certain ranges of abiotic and biotic characteristics mean that changes in these factors often create large differences in benthic community structure. Investigations into drivers of community structure have found distinct patterns of variation between ecosystems, but drivers of macroscale variation may differ from drivers of microscale variation. Such microscale variation in macroinvertebrate community structure as a function of abiotic conditions may be found in the confluence of two geologically distinct freshwater streams. Variation in the origin, underlying bedrock, and watershed of a stream results in drastically different physical and chemical characteristics and correspondingly distinct macroinvertebrate community structures. In areas where water from geologically distinct streams flows together, a mixing zone emerges with unique chemical and physical characteristics. There is little information on how invertebrate communities are structured within this mixing zone. To investigate this, we examined how the structure of the macroinvertebrate community changed downstream of the confluence. Up to thirty metres downstream, we found distinct stream sections that mirrored physical and chemical conditions found in limestone and freestone streams, and a mixing zone with emergent properties. These physical and chemical changes between sites were accompanied by shifts in macroinvertebrate community composition. Diversity indices indicated significantly higher diversity in freestone sites than in limestone sites or the mixing zone and there was a unique composition of genera in the mixing zone that were distinct from both limestone and freestone sites. Factors driving

  8. Wet separation processes as method to separate limestone and oil shale

    Science.gov (United States)

    Nurme, Martin; Karu, Veiko

    2015-04-01

    Biggest oil shale industry is located in Estonia. Oil shale usage is mainly for electricity generation, shale oil generation and cement production. All these processes need certain quality oil shale. Oil shale seam have interlayer limestone layers. To use oil shale in production, it is needed to separate oil shale and limestone. A key challenge is find separation process when we can get the best quality for all product types. In oil shale separation typically has been used heavy media separation process. There are tested also different types of separation processes before: wet separation, pneumatic separation. Now oil shale industry moves more to oil production and this needs innovation methods for separation to ensure fuel quality and the changes in quality. The pilot unit test with Allmineral ALLJIG have pointed out that the suitable new innovation way for oil shale separation can be wet separation with gravity, where material by pulsating water forming layers of grains according to their density and subsequently separates the heavy material (limestone) from the stratified material (oil shale)bed. Main aim of this research is to find the suitable separation process for oil shale, that the products have highest quality. The expected results can be used also for developing separation processes for phosphorite rock or all others, where traditional separation processes doesn't work property. This research is part of the study Sustainable and environmentally acceptable Oil shale mining No. 3.2.0501.11-0025 http://mi.ttu.ee/etp and the project B36 Extraction and processing of rock with selective methods - http://mi.ttu.ee/separation; http://mi.ttu.ee/miningwaste/

  9. Assessment of Rock Slope Stability in Limestone Quarries in the Tournai's Region (Belgium) Using Structural Data

    Science.gov (United States)

    Tshibangu, Jean-Pierre; Deloge, K. Pierre-Alexandre; Deschamps, Benoît; Coudyzer, Christophe

    The Tournais region is characterised by famous outcrops of carboniferous limestone which is mined out for cement and raw material production. The four main quarries found in the Region, i.e. Gaurain-Ramecroix, Milieu, Antoing and Lemay; are owned by the three main cement producers in Belgium: Italcimenti, Holcim and CBR. The global production of limestone is about 20 millions tons per year, giving big pits with depths up to 150 m. With the growth of the pits, the quarries are approaching each other leading to the problem of managing the reserves contained in the separating walls and their mechanical stability. The limestone deposit is composed of different seams having varying thickness, chemical com- position and even mechanical properties. The deposit has an overall horizontal dip and is intersected by two main sets of discontinuities with a spacing of about 10 m or less. It is also crossed by a set of east to west faults but the quarries are implanted in the in between areas, so to not be crossed by these faults. The layers and specially the shallow ones are characterised by a typical karstic weathering giving open or filled cavities. This paper presents the global work quarried out in order to study the stability of the Lemays quarry. First a description of the orientation and spacing of discontinuities is presented, and an attempt made to correlate to the development of weathering. Mechanical laboratory tests have been performed and a qualification of the rock mass assessed. A coupled approach is then presented using a mining planning analysis and mechanical simulation (i.e. Finite Element method).

  10. Estimation of deep infiltration in unsaturated limestone environments using cave lidar and drip count data

    Science.gov (United States)

    Mahmud, K.; Mariethoz, G.; Baker, A.; Treble, P. C.; Markowska, M.; McGuire, E.

    2016-01-01

    Limestone aeolianites constitute karstic aquifers covering much of the western and southern Australian coastal fringe. They are a key groundwater resource for a range of industries such as winery and tourism, and provide important ecosystem services such as habitat for stygofauna. Moreover, recharge estimation is important for understanding the water cycle, for contaminant transport, for water management, and for stalagmite-based paleoclimate reconstructions. Caves offer a natural inception point to observe both the long-term groundwater recharge and the preferential movement of water through the unsaturated zone of such limestone. With the availability of automated drip rate logging systems and remote sensing techniques, it is now possible to deploy the combination of these methods for larger-scale studies of infiltration processes within a cave. In this study, we utilize a spatial survey of automated cave drip monitoring in two large chambers of Golgotha Cave, south-western Western Australia (SWWA), with the aim of better understanding infiltration water movement and the relationship between infiltration, stalactite morphology, and unsaturated zone recharge. By applying morphological analysis of ceiling features from Terrestrial LiDAR (T-LiDAR) data, coupled with drip time series and climate data from 2012 to 2014, we demonstrate the nature of the relationships between infiltration through fractures in the limestone and unsaturated zone recharge. Similarities between drip rate time series are interpreted in terms of flow patterns, cave chamber morphology, and lithology. Moreover, we develop a new technique to estimate recharge in large-scale caves, engaging flow classification to determine the cave ceiling area covered by each flow category and drip data for the entire observation period, to calculate the total volume of cave discharge. This new technique can be applied to other cave sites to identify highly focussed areas of recharge and can help to better

  11. Assessing the Sensitivity of Mountain Forests to Site Degradation in the Northern Limestone Alps, Europe

    Directory of Open Access Journals (Sweden)

    Birgit Reger

    2015-05-01

    Full Text Available Because of some land-use practices (such as overstocking with wild ungulates, historical clear-cuts for mining, and locally persisting forest pasture, protective forests in the montane vegetation belt of the Northern Limestone Alps are now frequently overaged and poorly structured over large areas. Windthrow and bark beetle infestations have generated disturbance areas in which forests have lost their protective functions. Where unfavorable site conditions hamper regeneration for decades, severe soil loss may ensue. To help prioritize management interventions, we developed a geographic information system-based model for assessing sensitivity to site degradation and applied it to 4 test areas in the Northern Limestone Alps of Austria and Bavaria. The model consists of (1 analysis of site conditions and forest stand structures that could increase sensitivity to degradation, (2 evaluation of the sensitivity of sites and stands, and (3 evaluation and mapping of mountain forests' sensitivity to degradation. Site conditions were modeled using regression algorithms with data on site parameters from pointwise soil and vegetation surveys as responses and areawide geodata on climate, relief, and substrate as predictors. The resulting predictor–response relationships were applied to test areas. Stand structure was detected from airborne laser scanning data. Site and stand parameters were evaluated according to their sensitivity to site degradation. Sensitivities of sites and stands were summarized in intermediate-scale sensitivity maps. High sensitivity was identified in 3 test areas with pure limestone and dolomite as the prevailing sensitivity level. Moderately sensitive forests dominate in the final test area, Grünstein, where the bedrock in some strata contains larger amounts of siliceous components (marl, mudstone, and moraines; degraded and slightly sensitive forests were rare or nonexistent in all 4 test areas. Providing a comprehensive overview

  12. Bedrock stability in southeastern Sweden. Evidence from fracturing in the ordovician limestones of northern Oeland

    International Nuclear Information System (INIS)

    Milnes, A.G.; Gee, D.G.

    1992-09-01

    The stability of the bedrock in SE Sweden with regard to radioactive waste disposal has recently been the subject of some controversy. In order to better assess the age and significance of fracturing in the Precambrian basement at the site of the Aespoe Hard Rock Laboratory (HRL), near Oskarshamn, a detailed analysis of fracturing in the lower Ordovician limestones exposed along the west coast of the neighbouring island of Oeland has been carried out. The limestones form continuously exposed shore platforms, in segments up to 30 m broad and several kilometres long. These, and numerous quarries, provide ideal objects for quantitative analysis (ground and air photo mapping, scanline logging), and unique opportunities for investigating the amount of movement on the fractures, because of well-developed bedding and abundant rod-shaped fossils on the bedding surfaces. The fracture patterns are dominated by two sets of subvertical fractures, a NW trending closely spaced and strongly orientated set and a NNE-ENE trending widely spaced and variably orientated set. Only about 10% of the fractures in both sets show lateral fossil displacement, with maximum movement of 5 cm, and only 3% of the fractures show vertical displacement of bedding (maximum 8 cm). All in all, the lower Ordovician limestones along the exposed shoreline have suffered remarkably little deformation since deposition, i.e. over the last 500 million years. Appreciable bedrock instability, if it occurred, must have been concentrated offshore, or in the unexposed segments of the coastline, where some weak indications of slight movement (changes of a few metres in stratigraphic level) have been observed. Among other recommendations for further work, geophysical investigations to test these indications are suggested. (54 refs.)

  13. Modelling of limestone injection for SO2 capture in a coal fired utility boiler

    International Nuclear Information System (INIS)

    Kovacik, G.J.; Reid, K.; McDonald, M.M.; Knill, K.

    1997-01-01

    A computer model was developed for simulating furnace sorbent injection for SO 2 capture in a full scale utility boiler using TASCFlow TM computational fluid dynamics (CFD) software. The model makes use of a computational grid of the superheater section of a tangentially fired utility boiler. The computer simulations are three dimensional so that the temperature and residence time distribution in the boiler could be realistically represented. Results of calculations of simulated sulphur capture performance of limestone injection in a typical utility boiler operation were presented

  14. COPROLITES FROM THE DANIAN LIMESTONE (LOWER PALEOCENE) OF FAXE QUARRY, DENMARK

    DEFF Research Database (Denmark)

    Milàn, Jesper

    2010-01-01

    are attributed to sharks, and large, cylindrical coprolites with longitudinal striations on the surface are identified as crocodile coprolites. Fish and sharks are known from abundant finds of otoliths and teeth in Faxe Quarry, and crocodiles are known from finds of single bones and teeth.......A collection of coprolites found in the Danian (Lower Paleocene) limestone of Faxe Quarry, Denmark, is described and attributed to the respective producers. Small, drop-like specimens with weak signs of spiral coiling are attributed to fish. Larger, heteropolar, spirally-coiled specimens...

  15. Sponge assemblage of some Upper Permian reef limestones from Phrae province (Northern Thailand

    Directory of Open Access Journals (Sweden)

    Baba Senowbari-Daryan

    1994-12-01

    Full Text Available The sponge fauna of uppermost Permian reef or reefal limestones of the Phrae province in northern Thailand include representatives of hexactinellida, sclerospongea,"sphinctozoans", and "inozoans". The "sphinctozoans" and "inozoans"are described in detail. Following taxa are new:"Sphinctozoans": Phraethalamia tubulara n. gen., n. sp., Ambithalamia pérmican. gen., n. sp."Inozoans": Bisiphonella tubulara n. sp., Solutossaspongia crassimuralis n.gen., n. sp.The genus name Belyaevaspongia nom. nov. is proposed for PolysiphonellaBelyaeva, 1991 (in Boiko et al., 1991, non Polysiphonella Russo, 1981.

  16. Characteristics of a calcite "limestone"-marble from Macedonia, used as flux material

    Directory of Open Access Journals (Sweden)

    Hristova E.

    2003-01-01

    Full Text Available The phase characteristics of calcite "limestone"-marble from Banjany area village (near Skopje, Macedonia were examined by means of XRD, SEM microscope in polarizing and reflected lights, chemical, DT/TG-analyses. It was concluded as follows: - calcite (CaCO3 is a major mineral component (cca 80-90 % prevailing in the marble over the other minerals - dolomite is generally of minor importance (cca 10-20 % in the rock - quartz, micas graphite, pyrite represent typical accessories. As result of the mentioned phase characteristics, this raw materials was for a long time (more than 30 years used as flux in the iron and steel metallurgy in Macedonia.

  17. Three new species of Begonia (Begoniaceae from Limestone Hills in southwestern Sarawak, Borneo

    Directory of Open Access Journals (Sweden)

    Che-Wei Lin

    2017-04-01

    Full Text Available Most species of Begonia in Borneo, like those of other areas, are narrowly distributed and site-specific. In this study we report three new species of Begonia, namely B. felis C. W. Lin & C.-I Peng, B. kuchingensis C. W. Lin & C.-I Peng (sect. Petermannia and B. serianensis C. W. Lin & C.-I Peng (sect. Reichenheimia from the Padawan-Serian limestone hills in southwestern Sarawak. In addition to the taxonomic account, color plates, line drawings, a distribution map, and comparisons with phenetically similar species are provided to aid in identification.

  18. Haematological and physiological responses of brook charr, to untreated and limestone-neutralized acid mine drainage

    Energy Technology Data Exchange (ETDEWEB)

    Cole, M.B.; Arnold, D.E.; Watten, B.J.; Krise, W.F. [ABR Inc, Forest Grove, OR (USA). Environmental Research and Services

    2001-07-01

    Brook charr, Salvelinus fontinalis, exhibited depressed plasma sodium and elevated plasma glucose concentrations in untreated acid mine drainage effluent (AMD), at two dilutions. Plasma sodium and glucose concentrations remained stable in treated AMD, pulsed, fluidized beds of limestone and carbon-dioxide pre-treatment of influent, and in AMD-free water. Results indicate that effluents produced by this treatment system were not toxic to these fish, despite still containing moderate concentrations of manganese (3-4 mg l{sup 1} following dilution in exposure systems), and provide justification for field deployment and further biological testing of this treatment in the field.

  19. Chiritopsis longzhouensis, a New Species of Gesneriaceae from Limestone Areas in Guangxi, China

    Directory of Open Access Journals (Sweden)

    Bo Pan

    2010-11-01

    Full Text Available A new species of Gesneriaceae, Chiritopsis longzhouensis B. Pan & W. H. Wu from limestone areas in Guangxi, China, is described and illustrated. The new species is similar to C. jingxiensis Yan Liu, W. B. Xu & H. S. Gao in the corolla shape, but differs in its leaf blade 2-4 × 1.3-2.5 cm, appressed pilose on both surfaces, Cymes 5-10, 1-3-branched, each 5-25-flowered, filaments geniculate about 1 mm above base, sparsely glandular-puberulent, staminodes 3.

  20. Synthesis of Calcite Nano Particles from Natural Limestone assisted with Ultrasonic Technique

    Science.gov (United States)

    Handayani, M.; Sulistiyono, E.; Firdiyono, F.; Fajariani, E. N.

    2018-03-01

    This article represents a precipitation method assisted with ultrasonic process to synthesize precipitated calcium carbonate nano particles from natural limestone. The synthesis of nanoparticles material of precipitated calcium carbonate from commercial calcium carbonate was done for comparison. The process was performed using ultrasonic waves at optimum condition, that is, at temperature of 80oC for 10 minutes with various amplitudes. Synthesized precipitated calcium carbonate nanoparticles were characterized using X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM) and Particle Size Analyzer (PSA). The result of PSA measurements showed that precipitated calcium carbonate nano particles was obtained with the average size of 109 nm.

  1. Mill tailings based composites as paste backfill in mines of U-bearing dolomitic limestone ore

    Directory of Open Access Journals (Sweden)

    Sandeep Panchal

    2018-04-01

    Full Text Available This paper elaborates on the development of paste backfill using mill tailings generated during the processing of a uranium ore deposit hosted in dolomitic limestone. The tailings have been characterized in terms of the physical, chemical and mineralogical properties. Time-dependent rheological behaviors and geotechnical properties of cemented paste backfill (CPB are also determined. The studies show that the mill tailing has the potential to form paste and the CPB has adequate strength to provide support to mine pillars, roofs, and walls. Keywords: Mining engineering, Uranium ore deposit, Tailings, Cemented paste backfill (CPB, Rheology, Compressive strength

  2. Fault-related dolomitization in the Vajont Limestone (Southern Alps, Italy): photogrammetric 3D outcrop reconstruction, visualization with textured surfaces, and structural analysis

    OpenAIRE

    Bistacchi, Andrea; Balsamo, Fabrizio; Storti, Fabrizio; Mozafari, Mahtab; Swennen, Rudy; Solum, John; Taberner, Conxita

    2013-01-01

    The Vajont Gorge (Dolomiti Bellunesi, Italy) provides spectacular outcrops of Jurassic limestones (Vajont Limestone Formation) in which Mesozoic and Alpine faults and fracture corridors are continuously exposed. Some of these faults acted as conduits for fluids, resulting in structurally-controlled dolomitization of the Vajont Limestone, associated with significant porosity increase. We carried out a 3D surface characterization of the outcrops, combining high resolution topography and imaging...

  3. Identification and characterization of near surface cavities in Tuwaiq Mountain Limestone, Riyadh, KSA, “detection and treatment”

    Directory of Open Access Journals (Sweden)

    Ahmed Abd El Aal

    2017-03-01

    Full Text Available This study evaluates the capability of surface electrical resistivity technique for identifying the weak zones or subsurface cavities in karst area with limestone rocks. Weak zones or cavities near surface can be potentially dangerous and several problems are associated with collapse of roads or buildings accompanied by subsidence phenomena. Karst environments are characterized by distinctive landforms, which are related to dissolution and dominant subsurface drainage. The interaction of limestone with water is able to create karst features such as cavity, pinnacle, boulder and sinkhole through the dissolution process. The existence of subsurface karst features are always a matter of concern to engineers before any development starts because these features could cause disaster in the future. The study was conducted at Tuwaiq Mountain Limestone, Riyadh region, KSA with the objective to detect and treat karst features at limestone rocks. The karst features such as fill cavity, boulder, pinnacle, discontinuity and overhang were detected in the survey lines. The 2-D ER results showed a good correlation with all the borehole records in determining the subsurface of limestone formation. The 2-D ER method is capable in mapping karst features and bedrock depth. The ability of the electrical technique to produce high resolution images of the subsurface, which are useful for subsidence assessment is illustrated.

  4. The Suitability of Limestone from Pilaspi Formation (Middle-Late Eocene for Building Stone in Koya Area, NE Iraq

    Directory of Open Access Journals (Sweden)

    Hemn M. Omar

    2015-09-01

    Full Text Available Suitability of limestone rocks has a crucial importance when stones are used for constructing modern structure. The purpose of this study is to clarify the links between physical, mechanical properties of limestone rocks, also their quality to use as building materials. A total of six limestone rock samples were collected from three different outcrops locations within Pilaspi Formation in Koya area. Engineering geological and geotechnical properties of the limestone rocks in the study area were determined based on the field studies and laboratory tests. The field studies included observations/ measurements of rock mass characteristics such as color, grain size, orientation, bedding thickness and weathering state of the rock materials also spacing, persistence, roughness and infilling material of the discontinuities. Laboratory tests were carried out for determining water content, water absorption, density, uniaxial compressive strength, slake durability and porosity of the rock materials. The study results go well with the national and international standards (Iraqi Standards, 1989; American Society for Testing and Materials, 2004; International Society for Rock Mechanics, 1981 and have shown that the limestone rocks are acceptable for building stone.

  5. Near-real-time Forensic Disaster Analysis: experiences from hurricane Sandy

    Science.gov (United States)

    Kunz, Michael; Mühr, Bernhard; Schröter, Kai; Kunz-Plapp, Tina; Daniell, James; Khazai, Bijan; Wenzel, Friedemann; Vannieuwenhuyse, Marjorie; Comes, Tina; Münzberg, Thomas; Elmer, Florian; Fohringer, Joachim; Lucas, Christian; Trieselmann, Werner; Zschau, Jochen

    2013-04-01

    Hurricane Sandy was the last tropical cyclone of the 2012 Northern Atlantic Hurricane season that made landfall. It moved on an unusual track from the Caribbean to the East Coast of the United States from 24 to 30 October as a Category 1 and 2 Hurricane according to the Saffir-Simpson Scale. Along its path, the severe storm event caused widespread damage including almost 200 fatalities. In the early hours of 30 October, Sandy made landfall near Atlantic City, N.J. Sandy was an extraordinary event due to its multihazard nature and several cascading effects in the aftermath. From the hydro-meteorological perspective, most unusual was the very large spatial extent of up to 1,700 km. High wind speeds were associated with record breaking storm surges at the U.S. Mid- Atlantic and New England Coast during high (astronomical) tide, leading to widespread flooding. Though Sandy was not the most severe storm event in terms of wind speed and precipitation, the impact in the U.S. was enormous with total damage estimates of up to 90 billion US (own estimate from Dec. 2012). Although much better data emerge weeks after such an event, the Forensic Disaster Analysis (FDA) Task Force of the Center for Disaster Management and Risk Reduction Technology (CEDIM) made an effort to obtain a comprehensive and holistic overview of the causes, hazardous effects and consequences associated with Sandy immediately after landfall at the U.S. coast on 30 October 2012. This was done in an interdisciplinary way by collecting and compiling scattered and distributed information from available databases and sources via the Internet, by applying own methodologies and models for near-real time analyses developed in recent years, and by expert knowledge. This contribution gives an overview about the CEDIM-FDA analyses' results. It describes the situation that led to the extraordinary event, highlights the interaction of the tropical cyclone with other hydro-meteorological events, and examines the

  6. THE PROBLEMATIC OF SANDY LANDS IN PARANAVAI MUNICIPALITY –PR

    Directory of Open Access Journals (Sweden)

    Marcelo Eduardo Freres Stipp

    2005-05-01

    Full Text Available The sandy lands are a process of scouring with sand forming a sandy area, which correspondsto a reworking of the sands due its constant mobility, involving the transformation of notsolids deposits is sandy areas. This work tried to establish the characterization of thisphenomenon of scouring with sand in a local level, occurring in arenaceous areas in theNortheast of the state of Paraná, specifically in the urban site of Paranavaí. It was also madean evaluation of the environmental degradation as well as different causes for what provokedthese sandy areas. Being an area with a high level of soil decomposition with the highwaysroutes crossing it, it was necessary, besides bibliographic data that allowed a theoretical basis,a research applied in order to supply subsides for future planning related to the spaceorganization. The evolution of the use and soil occupation in this area has been processedwithin an urban planning which considered by no account neither soil characteristic, thevegetation nor the predominant climate in that region. The mechanisms of region atmospherecirculation were analyzed, the alterations or attributes of the climate as well, aiming toidentify the genesis of the erosion sandy and possible time and space distribution. Initially, themain characteristics of the region were collected, components e processes working on the landmodel. It was observed how it worked and the use and occupation of the soil in past times andcurrently. During 2004, using the Environmental Fragility Letter, the areas of erosion wereidentified, ravines and strong erosion that compounds the first stages of the focused problem.The sandy land is a process that involves erosion, transport, e accumulation, meaning most oftimes the loosing of Biosphere productivity. For monitoring these risk areas some measuringcanes were made to measure the soil loss, which were used in several spots of erosion in theurban area in Paranavaí. The measurement happened in

  7. Dynamic failure of dry and fully saturated limestone samples based on incubation time concept

    Directory of Open Access Journals (Sweden)

    Yuri V. Petrov

    2017-02-01

    Full Text Available This paper outlines the results of experimental study of the dynamic rock failure based on the comparison of dry and saturated limestone samples obtained during the dynamic compression and split tests. The tests were performed using the Kolsky method and its modifications for dynamic splitting. The mechanical data (e.g. strength, time and energy characteristics of this material at high strain rates are obtained. It is shown that these characteristics are sensitive to the strain rate. A unified interpretation of these rate effects, based on the structural–temporal approach, is hereby presented. It is demonstrated that the temporal dependence of the dynamic compressive and split tensile strengths of dry and saturated limestone samples can be predicted by the incubation time criterion. Previously discovered possibilities to optimize (minimize the energy input for the failure process is discussed in connection with industrial rock failure processes. It is shown that the optimal energy input value associated with critical load, which is required to initialize failure in the rock media, strongly depends on the incubation time and the impact duration. The optimal load shapes, which minimize the momentum for a single failure impact, are demonstrated. Through this investigation, a possible approach to reduce the specific energy required for rock cutting by means of high-frequency vibrations is also discussed.

  8. Removal of Iron and Manganese Using Cascade Aerator and Limestone Roughing Filter

    Directory of Open Access Journals (Sweden)

    Mohd Sanusi Azrin

    2016-01-01

    Full Text Available Combination between oxidation and filtration can be used for removing iron and manganese from groundwater especially when the concentrations of these metals were high. This study focused on the effectiveness of the cascade aerator and the size of the limestone filter media to remove iron and manganese from groundwater. Water samples used for this study were collected from orphanage home, Rumah Nur Kasih, Taiping. Universiti Sains Malaysia (USM has provided a tube well of 15 m depth and 150 mm diameter for the orphanage home. However, the water cannot be used for domestic consumption due to high amount of iron and manganese at 6.48 and 1.9 mg/L which exceeded the drinking water standard of 0.3 and 0.1 mg/L respectively. Using laboratory physical model, the study has shown that the removals of iron and manganese have reduce the concentration until 0.17 and 0.2 mg/L respectively. Thus, the results from this study which utilize cascade aerator and limestone roughing filter could be implemented on site for the community to use the ground water for domestic purposes.

  9. Physiological and behavioral responses of stonefly nymphs to enhanced limestone treatment of acid mine drainage.

    Science.gov (United States)

    Cole, M B; Arnold, D E; Watten, B J

    2001-03-01

    A new acid mine drainage (AMD) treatment system uses pulsed, fluidized beds of limestone, and carbon dioxide pretreatment of influent AMD, to enhance limestone neutralization of AMD. We conducted laboratory studies to evaluate the behavior and physiology of larval stoneflies (Pteronarcys proteus, Plecoptera) exposed to effluents produced by the treatment system. Survival, sodium balance, drift, and feeding responses by P. proteus to treated and untreated AMD were examined. P. proteus nymphs exhibited significant losses of whole body sodium in exposures to untreated AMD. Nymphs exposed to treated effluents experienced no loss of whole-body sodium. Nymphs exposed to untreated AMD showed elevated drift rates and depressed feeding rates relative to those of nymphs exposed to treated AMD, and to AMD-free controls. No significant differences in feeding or drift behavior occurred between nymphs exposed to treated effluents and those exposed to AMD-free controls. The treatment system, with and without CO2 pretreatment, provided water that was not toxic to the test animals, and that allowed normal behavioral and physiological function.

  10. Effect of limestone dust on vegetation in an area with a Mediterranean climate

    Energy Technology Data Exchange (ETDEWEB)

    Gale, J; Easton, J

    1979-01-01

    Possible effects of limestone dust on photosynthesis and transpiration throughout the summer season were assessed. Calculations were based on measurements of the dust accumulating on the leaves during the summer season, photosynthesis light curves of representative species, effect of dust on the optical characteristics of the leaves and stomatal diffusion resistances in the region of the quarry based on meteorological data. On a seasonal basis the dust was calculated to have only a very small effect in reducing photosynthesis and transpiration. A field experiment in which irrigated Xanthium strumarium plants were grown at different distances downwind from the quarry showed no deleterious effect of the dust even when plants close to the quarry were heavily coated. Comparison of aerial photographs taken just before the quarry was opened and 22 years later revealed no changes in the size, number or distribution pattern of the perennial, tree and shrub vegetation. It is concluded that, in an area with a Mediterranean climate, limestone dust, whilst being aesthetically offensive, does not significantly affect the growth of the natural vegetation. 13 references, 5 figures, 3 tables.

  11. Sulfur determination in concrete samples using laser-induced breakdown spectroscopy and limestone standards

    Science.gov (United States)

    Hrdlička, Aleš; Hegrová, Jitka; Novotný, Karel; Kanický, Viktor; Prochazka, David; Novotný, Jan; Modlitbová, Pavlína; Sládková, Lucia; Pořízka, Pavel; Kaiser, Jozef

    2018-04-01

    A LIBS equipment operating at 532 nm was optimized and used for sulfur determination in concrete samples. The influence of He atmosphere in a gas-tight chamber (1000-200 mbar) on S I 921.29 nm line sensitivity, signal-to-background and signal-to-noise ratio was studied at gate delays 100-2000 ns. Wide range of gate delays from 500 to about 1000 ns and pressures from several hundreds of mbar to the atmospheric pressure can be used for the desired detection of sulfur. The LIBS quantification was done using a simple calibration method. A synthetic limestone enriched by defined amounts of sodium sulfate was newly employed for direct quantification of S in concrete. This powder material was pressed into pellets and ablated with the LIBS system. The average content of sulfur as SO3 in the samples was 0.41-0.70 wt% by LIBS and 0.43-0.61 wt% by a reference standard procedure employing gravimetry and Inductively Coupled Plasma Triple Quad Mass Spectrometry (ICP-QQQMS). The uncertainty of the yielded LIBS results covers also the dispersion of the points in the calibration line and ranges from 16 to 28% at the probability level of 95%. The uncertainty of the ICP-QQQMS results was almost 10%. No correction on different signal response on the limestone and on the concrete was necessary.

  12. Application of restoration ecology principles to the practice of limestone quarry rehabilitation in Lebanon

    International Nuclear Information System (INIS)

    Khater, C.; Arnaud, M.

    2007-01-01

    Restoration ecology is an emerging science dealing with applied ecology and aiming at ''helping nature to recreate itself''. This comprehensive paper presents the findings and main results related to the analysis of natural vegetation dynamics on abandoned limestone quarries in Mediterranean environment. It aims to answer three basic questions: where, when and how should intervention by ecological restoration be achieved in abandoned limestone quarries. Results show that quarries are heterogeneous ecosystems and interventional strategies should be planned according to the different landforms observed. Quarry faces potentially host a particular saxicolous flora often composed of rare and endemic species, intervention is not recommended, unless required by urban planning issues. Intervention on platforms can be very expensive (substratum fracturing) and involves heavy engineering works. Restoration on quarry embankments aims at orienting and accelerating natural regeneration processes in order to shortcut the first stages naturally dominated by annuals and ruderal species. 27 species suitable for revegetation purposes have been identified for the different bioclimatic levels in Lebanon. They respond to two major criteria: availability in the natural surroundings (indigenous species) and adaptability to local conditions (pioneer adapted species). In conclusion, this paper suggests future openings for a development field integrating economical opportunities on solid scientific bases. (author)

  13. Influence of limestone doses in the Manganese absorption by Brachiaria decumbens

    International Nuclear Information System (INIS)

    Armelin, Maria Jose A.; Fulas, Paulo M.M.; Saiki, Mitiko; Primavesi, Odo; Primavesi, Ana C.

    2005-01-01

    To restore a degraded pasture of Brachiaria decumbens, located in Sao Carlos - SP, Southeastern Brazil, under tropical climate, an experiment was carried out to study the influence of different methods of the limestone doses application on manganese absorption by the aboveground part of the forage, during 3 years of treatment. The experimental design was randomized block, with 6 replications and 8 treatments. The 100m 2 blocks were established in the pasture. Each block received a sequence of limestone doses (0, 1, 2, 4, and 8 t/ha) applied on soil surface with NK and, 2 t/ha applied on soil surface with plus one annual application of 1t/ha and NK, 4t/ha buried in the soil with NK, 4t/ha applied on soil surface without NK. Forages samples were collected 14 cm above soil surface. Instrumental neutron activation analysis (INAA) followed by gamma-ray spectrometry was the analytical method used to determine manganese content. The statistical analysis showed some significant variations of this element absorption by the plant with regard to the treatments, but anything that could compromise the mineral nutrition of forage. Moreover, the quality of forage for the animal feeding showed suitable agreement to manganese requirement. INAA showed that it can be an alternative option for agronomical researches that require the knowledge of the manganese concentration. (author)

  14. Paleomagnetism of Cretaceous limestones from western Tarim basin suggests negligible latitudinal offset yet significant clockwise rotation

    Science.gov (United States)

    Tan, X.; Gilder, S.; Chen, Y.; Cogné, J. P.; Courtillot, V. E.; Cai, J.

    2017-12-01

    Large northward translation of central Asian crustal blocks has been reported from paleomagnetism of Cretaceous and Tertiary terrestrial sediments. This motion was initially taken as evidence of deformation occurred in the Asian interior as a result of indentation of the Indian Plate. However, because the amount of motion is far greater than geological observations, accuracy of the paleomagnetic record has become a controversial issue. To solve the problem, it has been shown that the latitudinal offset can be entirely attributed to inclination shallowing during deposition and compaction processes (Tan et al., 2003; Tauxe and Kent, 2004). On the other hand, coeval volcanic rocks from central Asia did record steeper paleomagnetic inclinations than terrestrial rocks (Gilder et al., 2003). To extend the effort of solving the controversy, we report paleomagnetic results of Cretaceous limestones from western Tarim basin. Our results show that the majority of our collections have been overprinted. Fortunately, a special type of limestones preserved stable characteristic remanence. Fold tests suggest a primary origin of the magnetization. Comparison of the paleomagnetic direction with the coeval expected direction from reference poles indicates a negligible amount of northward movement consistent with previous result of inclination correction based on magnetic fabrics, and a pattern of clockwise rotation symmetric with the style observed in the western flank of the Pamir ranges. Rock magnetic data will also be presented to support the accurate paleomagnetic record.

  15. Corrosion of limestone tablets in sulfidic ground-water: measurements and speleogenetic implications

    Directory of Open Access Journals (Sweden)

    Galdenzi Sandro

    2012-07-01

    Full Text Available The measurement of the weight loss in limestone tablets placed in the Grotta del Fiume (Frasassi, Italy provided data on the rate of limestone dissolution due to the sulfidic water and on the influence of local environmental conditions.A linear average corrosion rate of 24 mm ka-1 was measured in stagnant water, while the values were higher (68-119 mm ka-1 where the hydrologic conditions facilitate water movement and gas exchanges. In these zones the increase in water aggressivity is due to mixing with descending, O2-rich, seepage water and is also favored by easier gas exchange between ground-water and the cave atmosphere. Very intense corrosion was due to weakly turbulent flow, which caused evident changes in the tablets shape in few months. A comparison between the measured corrosion rates and the cave features showed that the values measured in the pools with stagnant water are too low to account for the largest solutional cave development, while the average values measured in the zones with moving water are compatible with the dimension of the cave rooms in the main cave levels, that must have developed when the base level was stable and hydrologic conditions favored the increase of water aggressivity.

  16. Diet of the Assamese macaque Macaca assamensis in lime-stone habitats of Nonggang, China

    Directory of Open Access Journals (Sweden)

    Qihai ZHOU, Hua WEI, Zhonghao HUANG, Chengming HUANG

    2011-02-01

    Full Text Available To enhance our understanding of dietary adaptations in macaques we studied the diet of the Assamese macaque Macaca assamensis in limestone seasonal rain forests at Nonggang Nature Reserve, China from September 2005 to August 2006. Our results show that although macaques fed on many plant species, 85.2% of the diet came from only 12 species, of which a bamboo species, Indocalamus calcicolus contributed to 62% of the diet. Young leaves were staple food items (74.1% of the diet for Assamese macaques at Nonggang, and constituted the bulk of monthly diets almost year-round, ranging from 44.9% (July to 92.9% (May. Young parts of Indocalamus calcicolus unexpanded leaves contributed to a large proportion of the young leaf diet in most months. Fruit accounted for only 17.4% of the diet, with a peak of consumption in July. We suggest that this highly folivorous diet may be related to the long lean season of fruit availability in limestone habitats as well as the utilization of cliffs of low fruit availability [Current Zoology 57 (1: 18–25, 2011].

  17. Laboratory Investigations in Support of Carbon Dioxide-Limestone Sequestration in the Ocean

    Energy Technology Data Exchange (ETDEWEB)

    Dan Golomb; Eugene Barry; David Ryan; Carl Lawton; Stephen Pennell; Peter Swett; Huishan Duan; Michael Woods

    2005-11-01

    This semi-annual progress reports includes further findings on CO{sub 2}-in-Water (C/W) emulsions stabilized by fine particles. In previous semi-annual reports we described the formation of stable C/W emulsions using pulverized limestone (CaCO{sub 3}), flyash, beach sand, shale and lizardite, a rock rich in magnesium silicate. For the creation of these emulsions we used a High-Pressure Batch Reactor (HPBR) equipped with view windows for illumination and video camera recording. For deep ocean sequestration, a C/W emulsion using pulverized limestone may be the most suitable. (a) Limestone (mainly CaCO{sub 3}) is cheap and plentiful; (b) limestone is innocuous for marine organisms (in fact, it is the natural ingredient of shells and corals); (c) it buffers the carbonic acid that forms when CO{sub 2} dissolves in water. For large-scale sequestration of a CO{sub 2}/H{sub 2}O/CaCO{sub 3} emulsion a device is needed that mixes the ingredients, liquid carbon dioxide, seawater, and a slurry of pulverized limestone in seawater continuously, rather than incrementally as in a batch reactor. A practical mixing device is a Kenics-type static mixer. The static mixer has no moving parts, and the shear force for mixing is provided by the hydrostatic pressure of liquid CO{sub 2} and CaCO{sub 3} slurry in the delivery pipes from the shore to the disposal depth. This semi-annual progress report is dedicated to the description of the static mixer and the results that have been obtained using a bench-scale static mixer for the continuous formation of a CO{sub 2}/H{sub 2}O/CaCO{sub 3} emulsion. The static mixer has an ID of 0.63 cm, length 23.5 cm, number of baffles 27. Under pressure, a slurry of CaCO{sub 3} in artificial seawater (3.5% by weight NaCl) and liquid CO{sub 2} are co-injected into the mixer. From the mixer, the resulting emulsion flows into a Jerguson cell with two oblong windows on opposite sides, then it is vented. A fully ported ball valve inserted after the Jerguson

  18. Characterization of limestone of region South and Southeast of Para; Caracterizacao de calcario da regiao Sul e Sudeste do Para

    Energy Technology Data Exchange (ETDEWEB)

    Marinho, A.R.O.; Vieira, J.H.A.; Antunes Junior, L.V.; Medeiros, A.C.; Souza, G.P., E-mail: marabaonline@gmail.com [Universidade Federal do Sul e Sudeste do Para (FEMAT/UNIFESSPA), Maraba, PA (Brazil)

    2014-07-01

    Limestone is used in daily activities, and it is common the use of products containing calcium carbonate in various applications, from construction to food production, air purification to sewage treatment, the sugar refining materials for the toothpaste, the manufacture of glass and steel in the manufacture of paper, plastics, paints, ceramics and many others. The Limestone present in the region of south and southeast of Para is presented in deposits that have not been explored on a large scale, being justified a deepening in characteristics thereof. For the characterization of the material, gross samples were comminuted by crushing and ball mill, sieved and then separated into aliquots. In the end were used fluorescence analysis of X-ray, diffraction X-rays, determination of the moisture and loss on ignition of the material at 950 °C for one hour, obtaining results of a dolomitic limestone. (author)

  19. T4-related bacteriophage LIMEstone isolates for the control of soft rot on potato caused by 'Dickeya solani'.

    Directory of Open Access Journals (Sweden)

    Evelien M Adriaenssens

    Full Text Available The bacterium 'Dickeya solani', an aggressive biovar 3 variant of Dickeya dianthicola, causes rotting and blackleg in potato. To control this pathogen using bacteriophage therapy, we isolated and characterized two closely related and specific bacteriophages, vB_DsoM_LIMEstone1 and vB_DsoM_LIMEstone2. The LIMEstone phages have a T4-related genome organization and share DNA similarity with Salmonella phage ViI. Microbiological and molecular characterization of the phages deemed them suitable and promising for use in phage therapy. The phages reduced disease incidence and severity on potato tubers in laboratory assays. In addition, in a field trial of potato tubers, when infected with 'Dickeya solani', the experimental phage treatment resulted in a higher yield. These results form the basis for the development of a bacteriophage-based biocontrol of potato plants and tubers as an alternative for the use of antibiotics.

  20. The chemometric study of limestone physico-chemical properties and thermal behavior for application in construction composites

    Directory of Open Access Journals (Sweden)

    Radulović Dragan

    2017-01-01

    Full Text Available The limestone, as an economically sustainable and easily available basic raw material, is frequently utilized in the building industry for resolving of the environmental protection issues. The limestone is incorporated in a cementitious system either by grinding with cement clinker, or by blending with the binder during concrete production. The employing of powdery limestone as partial cement replacement gives the construction composites with properties comparable to that of conventional concrete. The study of limestone thermal behavior and its chemistry is crucial for the prognosis of the designed composites properties. In this work, the instrumental techniques (atomic emission spectroscopy, differential thermal and thermo-gravimetric analysis, Fourier transform infrared spectroscopy and the Principal component analysis were employed to discriminate and classify 22 limestone types. The PCA statistical method, as a means of spectra and experimental data fingerprinting, grouped the samples in a multi-dimensional factor space producing four graphical prognosis - one for each instrumental method. DTA/TG peak values varied the most in a short range between 830-870°C, while FTIR spectra showed the highest diversity in the 867-887 cm-1 and 1237-1647 cm-1 ranges. This research was governed by an idea to reveal whether it is possible to differentiate various limestone types and to predict the possibility of their employment in construction composites on the basis of the results of instrumental and mathematical analyses. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. ON 172057, III 45008, TR 31055, TR 34006, and TR 34013

  1. Moisture distribution in the stone portal of a church: how it influences the salt accumulation in porous limestone

    Science.gov (United States)

    Török, Ákos; Galambos, Éva

    2017-04-01

    Mathias Church of Budapest (Hungary) is an emblematic stone monument that represents various phases of constructions from Medieval period to the early 20th century. The church is found at the elevated Castle Hill and forms a landmark at the UNESCO World Heritage Site of Budapest. Its main construction material is porous Miocene limestone. Besides porous limestone travertine was also extensively used. The current study focuses on the Medieval Gate of the church which encompasses richly decorated porous limestone ornaments. The gate is now sheltered and form an interior portal of the church. It shows various forms of stone decay. The most striking one is efflorescence of salts. This feature has become more intense in the past years leading to flaking and granular disintegration of the limestone, causing damage to the monument. This study focuses on the detection of moisture content within the stone structure and its role in the salt accumulation. To obtain this goal in situ moisture measurements were made along vertical profiles by a portable moisture detector (Gann-Hydromette). It allowed outlining the moisture distribution within the studied structure. The moisture measurement was combined with sampling of salt efflorescence and porous limestone of the gate, itself. The samples were tested by optical microscopy. Conductivity, salt content and main elements were also detected from solutions. Mineralogical composition was recorded by XRD and Thermogravimetric analyses. Magnesium-sulphates were found to be the main salts responsible for damages. Besides sulphates chlorides were also detected. Gypsum was also found in the weathering crusts of the previously exposed limestone surfaces. It accumulated in black crusts but was also detected in white efflorescence and below the stone surface. The salt distribution clearly correlates with the moisture content. The financial support of NKFI Fund (ref. no. K 116532) is appreciated.

  2. Hurricane Sandy Economic Impacts Assessment: A Computable General Equilibrium Approach and Validation

    Energy Technology Data Exchange (ETDEWEB)

    Boero, Riccardo [Los Alamos National Laboratory; Edwards, Brian Keith [Los Alamos National Laboratory

    2017-08-07

    Economists use computable general equilibrium (CGE) models to assess how economies react and self-organize after changes in policies, technology, and other exogenous shocks. CGE models are equation-based, empirically calibrated, and inspired by Neoclassical economic theory. The focus of this work was to validate the National Infrastructure Simulation and Analysis Center (NISAC) CGE model and apply it to the problem of assessing the economic impacts of severe events. We used the 2012 Hurricane Sandy event as our validation case. In particular, this work first introduces the model and then describes the validation approach and the empirical data available for studying the event of focus. Shocks to the model are then formalized and applied. Finally, model results and limitations are presented and discussed, pointing out both the model degree of accuracy and the assessed total damage caused by Hurricane Sandy.

  3. The Use of Ionizing Radiation to Prepare Polymeric Agro-waste Composite for Sandy Soil Application

    International Nuclear Information System (INIS)

    Elhady, M.A.; Elnahas, H.H.; Meligi, G.A.; Ammar, A.H.

    2015-01-01

    Super absorbent hydrogel composite (SHC) by radiation induced crosslinking of polyacrylamide (PAAM)/ rice straw (RS) composite and hydrophilic membrane system based on polyvinyl alcohol (PVA) for possible applications in agricultural field of sandy soil was studied. The factors affecting the quick and capacity for retaining irrigated water of swelling behaviour of prepared hydrogel composite through hydrophilic membrane system and increasing foaming/ porosity of the SHC were studied. The mechanism for this is most likely a prevention of irrigated water to pass through sandy particles for a time ranged from 20 to 40 min for the fluid uptake capacity and swelling of the SHC to take and swelling place without almost any loss of irrigated water. Effect of acid/ alkalinity (PH) and salt concentration were investigation.

  4. Enhanced benthic activity in sandy sublittoral sediments: Evidence from 13C tracer experiments

    DEFF Research Database (Denmark)

    Bühring, Solveig I.; Ehrenhauss, Sandra; Kamp, Anja

    2006-01-01

    In situ and on-board pulse-chase experiments were carried out on a sublittoral fine sand in the German Bight (southern North Sea) to investigate the hypothesis that sandy sediments are highly active and have fast turnover rates. To test this hypothesis, we conducted a series of experiments where we...... investigated the pathway of settling particulate organic carbon through the benthic food web. The diatom Ditylum brightwellii was labelled with the stable carbon isotope 13C and injected into incubation chambers. On-board incubations lasted 12, 30 and 132 h, while the in situ experiment was incubated for 32 h....... The study revealed a stepwise short-term processing of a phytoplankton bloom settling on a sandy sediment. After the 12 h incubation, the largest fraction of recovered carbon was in the bacteria (62%), but after longer incubation times (30 and 32 h in situ) the macrofauna gained more importance (15 and 48...

  5. Pore-size distribution and compressibility of coarse sandy subsoil with added biochar

    DEFF Research Database (Denmark)

    Petersen, C. T.; Hansen, E.; Larsen, H. H.

    2016-01-01

    Sustainable agricultural production on coarse sandy soil is constrained by the restricted growth of roots, and poor water and nutrient retention. Amending the soil with biochar can reduce these problems, but the processes involved are not known in detail. We investigated in the laboratory...... the effects of two fine-grained gasification biochars made of straw (LTST) and other materials (LTSN) and of one fast pyrolysis straw biochar (FPST) on pore-size distribution and soil compressibility when added to coarse sandy subsoil. Water retention and therefore pore-size distribution were affected...... systematically. All biochars converted drainable pore space with pore diameters in the range 60–300 µm into water-retaining pores of size 0.2–60 µm, which was taken as an estimate of available water capacity (AWC). Effects were linear over the whole range of biochar (0–4% by mass). The effect of LTST and LTSN...

  6. Nitrogen and Carbon Leaching in Repacked Sandy Soil with Added Fine Particulate Biochar

    DEFF Research Database (Denmark)

    Bruun, Esben W.; Petersen, Carsten; Strobel, Bjarne W.

    2012-01-01

    Biochar amendment to soil may affect N turnover and retention, and may cause translocation of dissolved and particulate C. We investigated effects of three fine particulate biochars made of wheat (Triticum aestivum L.) straw (one by slow pyrolysis and two by fast pyrolysis) on N and C leaching from...... repacked sandy soil columns (length: 51 cm). Biochar (2 wt%), ammonium fertilizer (NH4+, amount corresponding to 300 kg N ha-1) and an inert tracer (bromide) were added to a 3-cm top layer of sandy loam, and the columns were then irrigated with constant rate (36 mm d-1) for 15 d. The total amount...... of leachate came to about 3.0 water filled pore volumes (WFPVs). Our study revealed a high mobility of labile C components originating from the fine particulate fast pyrolysis biochar. This finding highlights a potential risk of C leaching coupled with the use of fast pyrolysis biochars for soil amendment...

  7. Firearms and accidental deaths: Evidence from the aftermath of the Sandy Hook school shooting.

    Science.gov (United States)

    Levine, Phillip B; McKnight, Robin

    2017-12-08

    Exposure to firearms increased substantially after the December 2012 shooting at Sandy Hook Elementary School in Newtown, Connecticut, where 20 children and 6 adults were killed. Gun sales spiked by 3 million, on the basis of the increase in the number of background checks for firearm purchases. Google searches for buying and cleaning guns increased. We used Vital Statistics mortality data to examine whether a spike in accidental firearm deaths occurred at the same time as the greater exposure to firearms. We also assessed whether the increase in these deaths was larger in those states where the spike in gun sales per capita was larger. We find that an additional 60 deaths overall, including 20 children, resulted from unintentional shootings in the immediate aftermath of Sandy Hook. Copyright © 2017 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.

  8. Tropical to extratropical: Marine environmental changes associated with Superstorm Sandy prior to its landfall

    Science.gov (United States)

    Zambon, Joseph B.; He, Ruoying; Warner, John C.

    2014-12-01

    Superstorm Sandy was a massive storm that impacted the U.S. East Coast on 22-31 October 2012, generating large waves, record storm surges, and major damage. The Coupled Ocean-Atmosphere-Wave-Sediment Transport modeling system was applied to hindcast this storm. Sensitivity experiments with increasing complexity of air-sea-wave coupling were used to depict characteristics of this immense storm as it underwent tropical to extratropical transition. Regardless of coupling complexity, model-simulated tracks were all similar to the observations, suggesting the storm track was largely determined by large-scale synoptic atmospheric circulation, rather than by local processes resolved through model coupling. Analyses of the sea surface temperature, ocean heat content, and upper atmospheric shear parameters showed that as a result of the extratropical transition and despite the storm encountering much cooler shelf water, its intensity and strength were not significantly impacted. Ocean coupling was not as important as originally thought for Sandy.

  9. Compost amendment of sandy soil affects soil properties and greenhouse tomato productivity

    DEFF Research Database (Denmark)

    Arthur, Emmanuel; Cornelis, W.; Razzaghi, Fatemeh

    2012-01-01

    Sandy soils, with low productivity, could be improved by compost application to sustain crop production. This study aimed to examine the effect of three compost types (vegetable, fruit and yard waste compost, garden waste compost, and spent mushroom compost) on basic properties of a loamy sand...... compost had greater effect in improving tomato productivity. A decade-long application of composts on loamy sand improved basic chemical and physical properties which were reflected in increased fruit yield in tomato. Since no negative effect of compost was observed, we suggest that sandy soils may serve...... and greenhouse tomato productivity. Disturbed and intact soil samples were taken from a decade-long compost field experiment on loamy sand with three compost types at application rate of 30 m3 ha-1 yr-1 (7.5 ton ha-1 yr-1). The soils were characterized for chemical and physical properties. Tomato was planted...

  10. IMPACT OF A USED STABILISER ON THE CALIFORNIA BEARING RATIO OF THE CLAYEY-SANDY SILT

    Directory of Open Access Journals (Sweden)

    Katarzyna Kamińska

    2017-01-01

    Full Text Available The paper aimed at the determination of the California Bearing Ratio of a stabilised and unstabilised fine-grained mineral soil. A clayey-sandy silt with the addition of 3, 6 and 10% of road stabilisers Solidex and Solidex A was used for the tests. The tests were carried out in the press Tritech 50 at the loading of 22 and 44 N. The stabilised samples were subjected to 7-days treatment, whereas unstabilised 4-days treatment. Stabilization with the applied road binders brought positive effects, there occurred a significant improvement in the mechanical properties of the clayey-sandy silt. The better binder, which significantly increased the value of the CBR ratio, was Solidex A. The use of hydraulic binders is of a great importance in road building, because their addition improves the mechanical properties of weaker mineral soils.

  11. Hurricane Sandy science plan: impacts of environmental quality and persisting contaminant exposure

    Science.gov (United States)

    Caskie, Sarah A.

    2013-01-01

    Hurricane Sandy devastated some of the most heavily populated eastern coastal areas of the Nation. With a storm surge peaking at more than 19 feet, the powerful landscape-altering destruction of Hurricane Sandy is a stark reminder of why the Nation must become more resilient to coastal hazards. In response to this natural disaster, the U.S. Geological Survey (USGS) received a total of $41.2 million in supplemental appropriations from the Department of the Interior (DOI) to support response, recovery, and rebuilding efforts. These funds support a science plan that will provide critical scientific information necessary to inform management decisions for recovery of coastal communities, and aid in preparation for future natural hazards. This science plan is designed to coordinate continuing USGS activities with stakeholders and other agencies to improve data collection and analysis that will guide recovery and restoration efforts. The science plan is split into five distinct themes: • Coastal topography and bathymetry

  12. Hurricane Sandy science plan: impacts to coastal ecosystems, habitats, and fish and wildlife

    Science.gov (United States)

    Campbell, Warren H.

    2013-01-01

    Hurricane Sandy devastated some of the most heavily populated eastern coastal areas of the Nation. With a storm surge peaking at more than 19 feet, the powerful landscape-altering destruction of Hurricane Sandy is a stark reminder of why the Nation must become more resilient to coastal hazards. In response to this natural disaster, the U.S. Geological Survey (USGS) received a total of $41.2 million in supplemental appropriations from the Department of the Interior (DOI) to support response, recovery, and rebuilding efforts. These funds support a science plan that will provide critical scientific information necessary to inform management decisions for recovery of coastal communities, and aid in preparation for future natural hazards. This science plan is designed to coordinate continuing USGS activities with stakeholders and other agencies to improve data collection and analysis that will guide recovery and restoration efforts. The science plan is split into five distinct themes: • Coastal topography and bathymetry

  13. Fine organic particles in a sandy beach system (Puck Bay, Baltic Sea

    Directory of Open Access Journals (Sweden)

    Lech Kotwicki

    2005-06-01

    Full Text Available A total of over 550 samples of particulate organic matter (POM were obtained from swash and groundwater samples taken on a monthly basis from seven localities on the sandy shores of Puck Bay in 2002 and 2003. Sandy sediment cores from the swash zone were collected to assess the amount of POM in the pore waters. The mean annual concentrations of POM varied between localities from 20 to 500 mg in groundwater and from 6 to 200 mg dm-3 in swash water. The carbon/nitrogen (C/N ratio in suspended matter was always higher in groundwater (annual mean 12 than in swash water (annual mean 7. The C/N ratio indicates a local, algal origin of POM in the shallow coastal zone.

  14. Kinetics of the direct sulfation of limestone at the initial stage of crystal growth of the solid product

    DEFF Research Database (Denmark)

    Hu, Guilin; Dam-Johansen, Kim; Wedel, Stig

    2011-01-01

    The direct sulfation of limestone was studied in a quartz bench scale fixed‐bed reactor with the technique of data deconvolution. The obtained results show that the direct sulfation of limestone has a two‐period kinetic behavior: a short initial sulfation period with high but fast decreasing...... such as SO2, O2, and CO2 and the temperature. The sulfation process in the initial stage of the period with product crystal growth can be described by the combination of the sulfation reaction at the gas–solid interface, diffusion of the product ions toward the product crystal grains, diffusion of carbonate...

  15. Laboratory study of SO2 dry deposition on limestone and marble: Effects of humidity and surface variables

    Science.gov (United States)

    Spiker, E. C.; Hosker, R.P.; Weintraub, V.C.; Sherwood, S.I.

    1995-01-01

    The dry deposition of gaseous air pollutants on stone and other materials is influenced by atmospheric processes and the chemical characteristics of the deposited gas species and of the specific receptor material. Previous studies have shown that relative humidity, surface moisture, and acid buffering capability of the receptor surface are very important factors. To better quantify this behavior, a special recirculating wind tunnel/environmental chamber was constructed, in which wind speed, turbulence, air temperature, relative humidity, and concentrations of several pollutants (SO2, O3, nitrogen oxides) can be held constant. An airfoil sample holder holds up to eight stone samples (3.8 cm in diameter and 1 cm thick) in nearly identical exposure conditions. SO2 deposition on limestone was found to increase exponentially with increasing relative humidity (RH). Marble behaves similarly, but with a much lower deposition rate. Trends indicate there is little deposition below 20% RH on clean limestone and below 60% RH on clean marble. This large difference is due to the limestone's greater porosity, surface roughness, and effective surface area. These results indicate surface variables generally limit SO2 deposition below about 70% RH on limestone and below at least 95% RH on marble. Aerodynamic variables generally limit deposition at higher relative humidity or when the surface is wet.The dry deposition of gaseous air pollutants on stone and other materials is influenced by atmospheric processes and the chemical characteristics of the deposited gas species and of the specific receptor material. Previous studies have shown that relative humidity, surface moisture, and acid buffering capability of the receptor surface are very important factors. To better quantify this behavior, a special recirculating wind tunnel/environmental chamber was constructed, in which wind speed, turbulence, air temperature, relative humidity, and concentrations of several pollutants (SO2, O3

  16. Stratigraphic variations and secondary porosity within the Maynardville Limestone in Bear Creek Valley, Y-12 Plant, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    Goldstrand, P.M.

    1995-05-01

    To evaluate groundwater and surface water contamination and migration near the Oak Ridge Y-12 plant, a Comprehensive Groundwater Monitoring Plan was developed. As part of the Maynardville exit pathways monitoring program, monitoring well clusters were ii installed perpendicular to the strike of the Maynardville Limestone, that underlies the southern part of the Y-12 Plant and Bear Creek Valley (BCV). The Maynardville Project is designed to locate potential exit pathways of groundwater, study geochemical characteristics and factors affecting the occurrence and distribution of water-bearing intervals, and provide hydrogeologic information to be used to reduce the potential impacts of contaminants entering the Maynardville Limestone

  17. Long-Term Observations of Dust Storms in Sandy Desert Environments

    Science.gov (United States)

    Yun, Hye-Won; Kim, Jung-Rack; Choi, Yun-Soo

    2015-04-01

    Mineral dust occupies the largest portion of atmospheric aerosol. Considering the numerous risks that dust poses for socioeconomic and anthropogenic activities, it is crucial to understand sandy desert environments, which frequently generate dust storms and act as a primary source of atmospheric aerosol. To identify mineral aerosol mechanisms, it is essential to monitor desert environmental factors involving dust storm generation in the long term. In this study, we focused on two major environmental factors: local surface roughness and soil moisture. Since installments of ground observation networks in sandy deserts are unfeasible, remote sensing techniques for mining desert environmental factors were employed. The test area was established within the Badain Jaran and Kubuqi Deserts in Inner Mongolia, China, where significant seasonal aeolian processes emit mineral dust that influences all of East Asia. To trace local surface roughness, we employed a multi-angle imaging spectroradiometer (MISR) image sequence to extract multi-angle viewing (MAV) topographic parameters such as normalized difference angular index, which represents characteristics of the target desert topography. The backscattering coefficient from various space-borne SAR and stereotopography were compared with MAV observations to determine calibrated local surface roughness. Soil moisture extraction techniques from InSAR-phase coherence stacks were developed and compiled with advanced scatterometer (ASCAT) soil moisture data. Combined with metrological information such as the European Centre for Medium-Range Weather Forecasts (ECMWF) ERA interim, correlations between intensity of sand dune activity as a proxy of aeolian processes in desert environments, surface wind conditions, and surface soil moisture were traced. Overall, we have confirmed that tracking sandy desert aeolian environments for long-term observations is feasible with space-borne, multi-sensor observations when combined with

  18. Behavioural adaptations of two sympatric sandhoppers living on a mesotidal European Atlantic sandy beach

    Science.gov (United States)

    Bessa, Filipa; Marques, João Carlos; Scapini, Felicita

    2014-06-01

    Behavioural adaptations of supralittoral species on sandy beaches are expressed as responses to environmental changes and constitute a key factor in their survival and evolution. Two sympatric talitrid amphipods (Talitrus saltator and Britorchestia brito) from a mesotidal exposed sandy beach on the European Atlantic coast (Portugal) were compared as regards orientation and littoral zonation patterns under natural conditions. Orientation experiments were carried out during spring and summer 2011 and 2012 at Quiaios beach, a highly dynamic exposed sandy beach. Multiple regression models were fitted to the angular data and the environmental effects on orientation were investigated for each species. Both talitrids were shown to be well orientated towards the shoreline and finely adapted to the mesotidal environment but a different use of local cues and climatic features between the two species was apparent. T. saltator showed a lower precision in the orientation performance (with a bimodal distribution sea- and land-wards), with less dependence on the sun cues and higher dependence on climatic features. In addition, the zonation of T. saltator was across the land-sea axis during both seasons. For B. brito the landscape vision, sun visibility and the tidal range enhanced the orientation to the shoreline. On this mesotidal Atlantic beach, T. saltator appeared to have a more flexible orientation with respect to B. brito, which appeared to be more dependent on the conditions offered by the intertidal zone, a behaviour confirmed by its restricted zonation below the high tide mark. Consequently, T. saltator showed a more flexible behaviour that may be considered an important evolutionary adaptation to dynamic and mesotidal sandy beaches.

  19. Sensitivity analysis of the surface water- groundwater interaction for the sandy area of the Netherlands

    OpenAIRE

    Gomez del Campo, E.; Jousma, G.; Massop, H.T.L.

    1993-01-01

    The "Sensitivity Analysis of the Surface Water- Groundwater Interaction for the Sandy Area of the Netherlands" was carried out in the framework of a bilateral research project in support of the implementation of a nationwide geohydrological information system (REGIS) in the Netherlands. This project, conducted in cooperation between the TNO Institute for Applied Scientific Research (IGG-TNO) and !he Winand Staring Centre for Integrated Land, Soil and Water Research (SC-DLO), is aimed at defin...

  20. EXPERIMENTAL DETERMINATION OF VARIABILITY IN PERMEABILITY OF SANDY SILT SOIL MIXED WITH FLY ASH IN PROPORTIONATE

    OpenAIRE

    Rasna Sharma*, Dr. M.K. Trivedi

    2016-01-01

    This paper presents the experimental determination of variability in permeability of sandy silt soil by blending with fly ash. The grain size, porosity, structure of the soil, specific gravity of the soil, viscosity and temperature are important factors in varying the permeability of the soil. Permeability is the flow conduction property of the soil. The void ratio with in the soil plays a vital role in varying the permeability. By blending with finer grains like fly ash in the soil with sand...