Total OH Reactivity Measurements in the Boreal Forest

Science.gov (United States)

Praplan, A. P.; Hellén, H.; Hakola, H.; Hatakka, J.

2015-12-01

INTRODUCTION Atmospheric total OH reactivity (Rtotal) can be measured (Kovacs and Brune, 2001; Sinha et al., 2008) or it can be calculated according to Rtotal = ∑i kOH+X_i [Xi] where kOH+X_i corresponds to the reaction rate coefficient for the reaction of OH with a given compound Xi and [Xi] its concentration. Studies suggest that in some environments a large fraction of missing reactivity, comparing calculated Rtotal with ambient total OH reactivity measurements (Di Carlo et al., 2004; Hofzumahaus et al., 2009). In this study Rtotal has been measured using the Comparative Reactivity Method (Sinha et al., 2008). Levels of the reference compound (pyrrole, C4H5N) are monitored by gas chromatography every 2 minutes and Rtotal is derived from the difference of reactivity between zero and ambient air. RESULTS Around 36 hours of preliminary total OH reactivity data (30 May until 2 June 2015) are presented in Fig. 1. Its range matches previous studies for this site (Nölscher et al., 2012; Sinha et al., 2010) and is similar to values in another pine forest (Nakashima et al., 2014). The setup used during the period presented here has been updated and more recent data will be presented, as well as a comparison with calculated OH reactivity from measured individual species. ACKNOWLEDGEMENTS This work was supported by Academy of Finland (Academy Research Fellowship No. 275608). The authors acknowledge Juuso Raine for technical support. REFERENCES Di Carlo et al. (2004). Science 304, 722-725.Hofzumahaus et al. (2009). Science 324, 1702-1704.Kovacs and Brune (2001). J. Atmos. Chem. 39, 105-122.Nakashima et al. (2014). Atmos. Env. 85, 1-8.Nölscher et al. (2012). Atmos. Chem. Phys. 12, 8257-8270.Sinha et al. (2008). Atmos. Chem. Phys. 8, 2213-2227.Sinha et al. (2010). Environ. Sci. Technol. 44, 6614-6620.

The effect of NaOH and KOH on the characterization of meso porous AlOOH nano structures in the hydrothermal route

International Nuclear Information System (INIS)

Haghnazari, N.; Abdollahifar, M.; Jahani, F.

2014-01-01

Meso porous AlOOH was synthesized by hydrothermal treatment from aluminium nitrate and NaOH or KOH. The effect of NaOH and KOH as precipitating agents on the characterization of samples were investigated. XRD, Ftir, FESEM and N 2 adsorption-desorption analytical techniques were used to characterize the products. Our results showed that using KOH as precipitating agent was favour-able for the formation of meso porous and crystalline AlOOH with high Bet-specific surface area of 98 m 2 /g. (Author)

The effect of NaOH and KOH on the characterization of meso porous AlOOH nano structures in the hydrothermal route

Energy Technology Data Exchange (ETDEWEB)

Haghnazari, N.; Abdollahifar, M.; Jahani, F., E-mail: abdollahifar@gmail.com [Islamic Azad University, Kermanshah Branch, Department of Chemical Engineering, 67131 Kermanshah (Iran, Islamic Republic of)

2014-10-01

Meso porous AlOOH was synthesized by hydrothermal treatment from aluminium nitrate and NaOH or KOH. The effect of NaOH and KOH as precipitating agents on the characterization of samples were investigated. XRD, Ftir, FESEM and N{sub 2} adsorption-desorption analytical techniques were used to characterize the products. Our results showed that using KOH as precipitating agent was favour-able for the formation of meso porous and crystalline AlOOH with high Bet-specific surface area of 98 m{sup 2}/g. (Author)

Bio diesel Production via Transesterification of Palm Oil Using NaOH/ Al2O3 Catalysts

International Nuclear Information System (INIS)

Taufiq Yap Yun Hin; Nurul Fitriyah Abdullah; Mahiran Basri; Taufiq Yap Yun Hin; Nurul Fitriyah Abdullah

2011-01-01

Due to the increase in price of petroleum and environmental concerns, the search for alternative fuels has gained importance. In this work, bio diesel production by transesterification of palm oil with methanol has been studied in a heterogeneous system using sodium hydroxide loaded on alumina (NaOH/ Al 2 O 3 ). NaOH/ Al 2 O 3 catalyst was prepared by impregnation of alumina with different amount of an aqueous solution of sodium hydroxide followed by calcination in air for 3 h. The prepared catalysts were then characterized by using x-ray diffraction (XRD), Fourier transform infrared spectrometer (FT-IR), Brunner-Emmett-Teller surface area measurement (BET), scanning electron microscopy (SEM) and temperature-programmed desorption of CO 2 (CO 2 -TPD). Moreover, the dependence of the conversion of palm oil on the reactions variables such as the molar ratio of methanol/oil, the amount of catalysts used, reaction temperatures and reaction times were performed. The conversion of 99 % was achieved under the optimum reaction conditions. The bio diesel obtained was characterized by FT-IR and the pour point was measured. (author)

Influence of 8-hydroxyquinoline addition on the corrosion behavior of commercial Al and Al-HO411 alloys in NaOH aqueous media

International Nuclear Information System (INIS)

Soliman, H.N.

2011-01-01

Highlights: → The corrosion of commercial Al alloy is higher than that of Al-HO411 alloy. → The inhibition efficiency increases with the increasing of 8-hydroxyquinoline (8HQ) concentration. → The inhibition efficiencies of Al-HO411 samples are higher than those of commercial Al. → The 8HQ is promising candidate to be added to the coating systems as active anti-corrosive component for corrosion protection of both alloys. - Abstract: The effect of 8-hydroxyquinoline (8HQ) on the corrosion inhibition of commercial Al and Al-HO411 alloys has been investigated in NaOH solutions. Results showed that the inhibition efficiency was increased with increasing concentration of 8HQ. Al-HO411 alloy exhibited higher corrosion resistance and inhibition efficiency than the commercial Al. Examination of both samples was studied by means of optical microscope as well as energy-dispersive X-ray spectrometer. The crystallographic structure of both samples was analyzed by means of X-ray diffractometry. It was observed that protective films are formed on the surfaces that play an essential role in the corrosion inhibition of the alloys under investigation.

Calcioferrite with composition (Ca3.94Sr0.06Mg1.01(Fe2.93Al1.07(PO46(OH4·12H2O

Directory of Open Access Journals (Sweden)

Barbara Lafuente

2014-03-01

Full Text Available Calcioferrite, ideally Ca4MgFe3+4(PO46(OH4·12H2O (tetracalcium magnesium tetrairon(III hexakis-phosphate tetrahydroxide dodecahydrate, is a member of the calcioferrite group of hydrated calcium phosphate minerals with the general formula Ca4AB4(PO46(OH4·12H2O, where A = Mg, Fe2+, Mn2+ and B = Al, Fe3+. Calcioferrite and the other three known members of the group, montgomeryite (A = Mg, B = Al, kingsmountite (A = Fe2+, B = Al, and zodacite (A = Mn2+, B = Fe3+, usually occur as very small crystals, making their structure refinements by conventional single-crystal X-ray diffraction challenging. This study presents the first structure determination of calcioferrite with composition (Ca3.94Sr0.06Mg1.01(Fe2.93Al1.07(PO46(OH4·12H2O based on single-crystal X-ray diffraction data collected from a natural sample from the Moculta quarry in Angaston, Australia. Calcioferrite is isostructural with montgomeryite, the only member of the group with a reported structure. The calcioferrite structure is characterized by (Fe/AlO6 octahedra (site symmetries 2 and -1 sharing corners (OH to form chains running parallel to [101]. These chains are linked together by PO4 tetrahedra (site symmetries 2 and 1, forming [(Fe/Al3(PO43(OH2] layers stacking along [010], which are connected by (Ca/Sr2+ cations (site symmetry 2 and Mg2+ cations (site symmetry 2; half-occupation. Hydrogen-bonding interactions involving the water molecules (one of which is equally disordered over two positions and OH function are also present between these layers. The relatively weaker bonds between the layers account for the cleavage of the mineral parallel to (010.

Vibrational spectroscopic study of poldervaartite CaCa[SiO3(OH)(OH)

Science.gov (United States)

Frost, Ray L.; López, Andrés; Scholz, Ricardo; Lima, Rosa Malena Fernandes

2015-02-01

We have studied the mineral poldervaartite CaCa[SiO3(OH)(OH)] which forms a series with its manganese analogue olmiite CaMn[SiO3(OH)](OH) using a range of techniques including scanning electron microscopy, thermogravimetric analysis, Raman and infrared spectroscopy. Chemical analysis shows the mineral is reasonably pure and contains only calcium and manganese with low amounts of Al and F. Thermogravimetric analysis proves the mineral decomposes at 485 °C with a mass loss of 7.6% compared with the theoretical mass loss of 7.7%. A strong Raman band at 852 cm-1 is assigned to the SiO stretching vibration of the SiO3(OH) units. Two Raman bands at 914 and 953 cm-1 are attributed to the antisymmetric vibrations. Intense prominent peaks observed at 3487, 3502, 3509, 3521 and 3547 cm-1 are assigned to the OH stretching vibration of the SiO3(OH) units. The observation of multiple OH bands supports the concept of the non-equivalence of the OH units. Vibrational spectroscopy enables a detailed assessment of the molecular structure of poldervaartite.

Tiberiobardiite, Cu9Al(SiO3OH2(OH12(H2O6(SO41.5·10H2O, a New Mineral Related to Chalcophyllite from the Cretaio Cu Prospect, Massa Marittima, Grosseto (Tuscany, Italy: Occurrence and Crystal Structure

Directory of Open Access Journals (Sweden)

Cristian Biagioni

2018-04-01

Full Text Available The new mineral species tiberiobardiite, ideally Cu9Al(SiO3OH2(OH12(H2O6(SO41.5·10H2O, has been discovered in the Cretaio Cu prospect, Massa Marittima, Grosseto, Tuscany, Italy, as very rare, light green, vitreous, tabular {0001}, pseudo-hexagonal crystals, up to 200 μm in size and 5 μm in thickness, associated with brochantite. Electron microprobe analysis gave (in wt %, average of 5 spot analyses: SO3 10.37, P2O5 3.41, As2O5 0.05, SiO2 8.13, Al2O3 5.54, Fe2O3 0.74, CuO 62.05, and ZnO 0.03, for a total of 90.32. Based on an idealized O content of 42 atoms per formula unit, assuming the presence of 16 H2O groups and 13.5 cations (without H, the empirical formula of tiberiobardiite is (Cu8.69Al0.21Fe0.10Σ9.00Al1.00(Si1.51P0.54Σ2.05S1.44O12.53(OH13.47·16H2O. The main diffraction lines, corresponding to multiple hkl indices, are [d in Å (relative visual intensity]: 9.4 (s, 4.67 (s, 2.576 (m, 2.330 (m, and 2.041 (mw. The crystal structure study revealed tiberiobardiite to be trigonal, space group R 3 ¯ , with unit-cell parameters a = 10.6860(4, c = 28.3239(10 Å, V = 2801.0(2 Å3, and Z = 3. The crystal structure was refined to a final R1 = 0.060 for 1747 reflections with Fo > 4σ (Fo and 99 refined parameters. Tiberiobardiite is the Si-analogue of chalcophyllite, with Si4+ replacing As5+ through the coupled substitution As5+ + O2− = Si4+ + (OH−. The name tiberiobardiite honors Tiberio Bardi (b. 1960 for his contribution to the study of the mineralogy of Tuscany.

Structure, surface area and morphology of aluminas from thermal decomposition of Al(OH(CH3COO2 crystals

Directory of Open Access Journals (Sweden)

KIYOHARA PEDRO K.

2000-01-01

Full Text Available Crystalline aluminium hydroxiacetate was prepared by reaction between aluminium powder (ALCOA 123 and aqueous solution of acetic acid at 96ºC ±1ºC. The white powder of Al(OH(CH3COO2 is constituted by agglomerates of crystalline plates, having size about 10mum. The crystals were fired from 200ºC to 1550ºC, in oxidizing atmosphere and the products characterized by X-ray diffraction, scanning electron microscopy and surface area measurements by BET-nitrogen method. Transition aluminas are formed from heating at the following temperatures: gamma (300ºC; delta (750ºC; alpha (1050ºC. The aluminas maintain the original morphology of the Al(OHAc2 crystal agglomerates, up to 1050ºC, when sintering and coalescence of the alpha-alumina crystals start and proceed up to 1550ºC. High surface area aluminas are formed in the temperature range of 700ºC to 1100ºC; the maximum value of 198m²/g is obtained at 900ºC, with delta-alumina structure. The formation sequence of transition aluminas is similar to the sequence from well ordered boehmite, but with differences in the transition temperatures and in the development of high surface areas. It is suggested that the causes for these diversities between the two sequences from Al(OH Ac2 and boehmite are due to the different particle sizes, shapes and textures of the gamma-Al2O3 which acts as precursor for the sequence gamma- to alpha-Al2O3.

Characterization of hydroxyapatite coatings deposited by hydrothermal electrochemical method on NaOH immersed Ti6Al4V

International Nuclear Information System (INIS)

He, Daihua; Liu, Ping; Liu, Xinkuan; Ma, Fengcang; Chen, Xiaohong; Li, Wei; Du, Jiandi; Wang, Pu; Zhao, Jun

2016-01-01

The hydrothermal electrochemical method was used to deposit hydroxyapatite coating on Ti6Al4V. In order to improve the bonding strength between the coating and substrate, the substrates were modified by 8 M NaOH solution before the deposition. The effects of immersing time on the substrate, on the hydroxyapatite coating, and on the bonding strength were studied. X-Ray Diffraction, Scanning Electron Microscope, Fourier Transform Infrared Spectroscopy and Drop Shape Analysis Method were applied. And the crystallinity of hydroxyapatite coating was calculated. The results show that immersing treatment effects the phase compositions, the microstructure and the wettability of the substrate surface. A porous, three-dimensional network structure is formed on the Ti6Al4V surface through the NaOH immersion. The pore size and depth increase with the increase of immersing time from 12 to 48 h. The surface microstructure of Ti6Al4V with 60 h′ immersion time was different from the others. The modification treatment can improve the bonding strength between hydroxyapatite coating and the substrate obviously. The value of the bonding strength with the substrate immersed for 48 h is larger than those of the others. A bone-like apatite layer forms on the coating after 3 days of soaking in SBF, implying with good bioactivity of the hydroxyapatite coatings deposited by the method. The surface characteristics of the sample immersed with 48 h are more conductive to the deposition of hydroxyapatite and to the improvement of the bonding strength. The formation mechanism of hydroxyapatite coating deposited by hydrothermal electrochemical method was discussed. - Highlights: • Immerse Ti6Al4V alloy with NaOH solution for different immersing time. • We deposit hydroxyapatite coating by hydrothermal electrochemical method. • We examine changes of composition, microstructure, bonding strength and bioactivity of the hydroxyapatite coating. • 48 h is the optimal immersing time. • We

In situ attenuated total reflection infrared (ATR-IR) study of the adsorption of NO2-, NH2OH, and NH4+ on Pd/Al2O3 and Pt/Al2O3.

NARCIS (Netherlands)

Ebbesen, S.D.; Mojet, Barbara; Lefferts, Leonardus

2008-01-01

In relation to the heterogeneous hydrogenation of nitrite, adsorption of NO2-, NH4+, and NH2OH from the aqueous phase was examined on Pt/Al2O3, Pd/Al2O3, and Al2O3. None of the investigated inorganic nitrogen compounds adsorb on alumina at conditions presented in this study. NO2-(aq) and NH4+(aq) on

Microstructural Characterization of Water-Rich Boehmite (AlO(OH)): TEM Correlation of Apparently Divergent XRD and TGA Results

International Nuclear Information System (INIS)

Allard, L.F.; Anovitz, L.M.; Benezeth, P.; Coffey, D.W.; Palmer, D.A.; Porter, W.D.; Wesolowski, D.J.

1999-01-01

An understanding of the solid-phase thermodynamics and aqueous speciation of aluminum is critical to our ability to understand and predict processes in a wide variety of geologic and industrial settings. Boehmite (AIO(OH)) is an important phase in the system Al 2 O 3 -H 2 O that has been the subject of a number of structural and thermodynamic studies since its initial synthesis [l] and discovery in nature [2]. Unfortunately, it has long been recognized that thermogravimetric analysis (TGA) of both synthetic and natural boehmite samples (that appear well crystallized by powder XRD methods) yields significant excess water - typically losing 16-16.5 wt. % on heating as compared with a nominal expected weight loss of 15.0 wt. % [3,4]. The boehmite used in our experiments was synthesized hydrothermally from acid-washed gibbsite (Al(OH) 3 ) at 200C. Powder XRD and SEM examination showed no evidence of the presence a contaminant phase. The TGA patterns do not suggest that this is due to adsorbed water, so a structural source is likely. We therefore undertook to examine this material by TEM to clarify this phenomenon

Layered Ni(OH)2-Co(OH)2 films prepared by electrodeposition as charge storage electrodes for hybrid supercapacitors.

Science.gov (United States)

Nguyen, Tuyen; Boudard, Michel; Carmezim, M João; Montemor, M Fátima

2017-01-04

Consecutive layers of Ni(OH) 2 and Co(OH) 2 were electrodeposited on stainless steel current collectors for preparing charge storage electrodes of high specific capacity with potential application in hybrid supercapacitors. Different electrodes were prepared consisting on films of Ni(OH) 2 , Co(OH) 2 , Ni 1/2 Co 1/2 (OH) 2 and layered films of Ni(OH) 2 on Co(OH) 2 and Co(OH) 2 on Ni(OH) 2 to highlight the advantages of the new architecture. The microscopy studies revealed the formation of nanosheets in the Co(OH) 2 films and of particles agglomerates in the Ni(OH) 2 films. Important morphological changes were observed in the double hydroxides films and layered films. Film growth by electrodeposition was governed by instantaneous nucleation mechanism. The new architecture composed of Ni(OH) 2 on Co(OH) 2 displayed a redox response characterized by the presence of two peaks in the cyclic voltammograms, arising from redox reactions of the metallic species present in the layered film. These electrodes revealed a specific capacity of 762 C g -1 at the specific current of 1 A g -1 . The hybrid cell using Ni(OH) 2 on Co(OH) 2 as positive electrode and carbon nanofoam paper as negative electrode display specific energies of 101.3 W h g -1 and 37.8 W h g -1 at specific powers of 0.2 W g -1 and 2.45 W g -1 , respectively.

Colloidal stability of Ni(OH){sub 2} in water and its dispersion into a ceramic matrix from the reaction media to obtain Ni/Al{sub 2}O{sub 3} materials

Energy Technology Data Exchange (ETDEWEB)

Cabanas-Polo, S.; Ferrari, B.; Sanchez-Herencia, A. J.

2014-07-01

Ni/Al{sub 2}O{sub 3} composites have been fabricated by slip casting of concentrated Ni(OH){sub 2}/Al{sub 2}O{sub 3} suspensions and subsequent in situ reduction to metallic nickel during sintering. For that, the synthesis assisted by ultrasound of both α- and β-Ni(OH){sub 2} polymorphs, as well as their colloidal stability, have been studied. The structural differences between both polymorphs have been thoroughly studied by means of XRD, FTIR, DTA-TG, SSA, SEM and TEM, in order to optimize the starting suspensions. This way, the IEP of both polymorphs have been established (9.7 y 12 for β- and α-Ni(OH){sub 2}, respectively), as well as the optimal content of an anionic dispersant (PAA) to stabilize the particles (0.8 wt. % for beta phase and 3.0 wt. % for alpha phase). Three different Ni/Al{sub 2}O{sub 3} composites, with a high dispersion degree of the metallic phase, have been obtained considering the potential vs. particles distance curve of the Ni(OH){sub 2}, and their structure has been discussed in terms of the strength of the agglomerates and/or aggregates of the Ni(OH){sub 2}. (Author)

OH+ IN DIFFUSE MOLECULAR CLOUDS

International Nuclear Information System (INIS)

Porras, A. J.; Federman, S. R.; Welty, D. E.; Ritchey, A. M.

2014-01-01

Near ultraviolet observations of OH + and OH in diffuse molecular clouds reveal a preference for different environments. The dominant absorption feature in OH + arises from a main component seen in CH + (that with the highest CH + /CH column density ratio), while OH follows CN absorption. This distinction provides new constraints on OH chemistry in these clouds. Since CH + detections favor low-density gas with small fractions of molecular hydrogen, this must be true for OH + as well, confirming OH + and H 2 O + observations with the Herschel Space Telescope. Our observed correspondence indicates that the cosmic ray ionization rate derived from these measurements pertains to mainly atomic gas. The association of OH absorption with gas rich in CN is attributed to the need for a high enough density and molecular fraction before detectable amounts are seen. Thus, while OH + leads to OH production, chemical arguments suggest that their abundances are controlled by different sets of conditions and that they coexist with different sets of observed species. Of particular note is that non-thermal chemistry appears to play a limited role in the synthesis of OH in diffuse molecular clouds

Conversion of CH/sub 3/OH into olefins over Al/sub 2/O/sub 3/Cr/sub 2/O/sub 3/ treated with CF/sub 3/Cl

Energy Technology Data Exchange (ETDEWEB)

Kurosaki, A; Okazaki, S

1983-05-01

Hydrocarbon production from methanol has become an important process for obtaining materials such as ethylene and propylene from coal, instead of petroleum. A mixed oxide of Al and Cr having an atomic ratio (Al/Cr) of around 9 showed catalytic activity for the conversion of CH/sub 3/OH into olefins and aromatic compounds after treatment with CF/sub 3/Cl at 450/sup 0/C. The mixed oxide treated with CF/sub 3/Cl adsorbed a considerable amount of NH/sub 3/ even at temperatures as high as 500/sup 0/C. Analyses of the compositions on the surface layer by using XPS showed that the F component was predominantly bound to Al, not to Cr. Strong acid sites related to the less crystallized AlF/sub 3/ seemed to be able to promote the conversion of CH/sub 3/OH.

OH-point defects in quartz in B- and Li-bearing systems and their application to pegmatites

Science.gov (United States)

Baron, M. A.; Stalder, R.; Konzett, J.; Hauzenberger, C. A.

2015-01-01

OH incorporation in quartz in Al-, B- and Li-bearing systems (granitic systems containing tourmaline or spodumene) was studied experimentally in order to investigate the effect of pressure, temperature and chemical impurities on the generation of OH-defects. High-pressure experiments were carried out at pressures between 5 and 25 kbar and temperatures between 800 and 900 °C, and OH-contents in quartz were calculated from IR absorption spectra measured on oriented quartz crystals. IR absorption features were assigned to impurity substitutions, such as AlOH (3,420, 3,379 and 3,315 cm-1) and BOH (3,595 cm-1), LiOH (3,483 cm-1), and hydrogarnet substitution (4H)Si defects (3,583 cm-1). Results indicate a negative correlation of incorporated Al-specific OH-defect content versus pressure (630 ± 130 wt ppm H2O at 5 kbar to 102 ± 6 wt ppm H2O at 25 kbar), but no clear correlation of B-specific OH-defects with pressure. In runs initially containing spodumene, virtually OH-free quartzes were observed at pressures ≥10 kbar, where impurity cations compensate each other forming an anhydrous eucryptite-defect component. In contrast, at 5 kbar, both Li- ad Al-specific OH-defects are observed (corresponding to 470 ± 75 wt ppm H2O). Results from this study may therefore be used to monitor formation conditions of quartz in terms of pressure and trace metal saturation of the crystallizing petrological system. IR spectra obtained from natural quartz grains from a tourmaline-bearing pegmatite exhibit B- and Al-related OH-bands. The B-related OH-band is also exhibited in quartz from a tourmaline + spodumene-bearing pegmatite. Li- and Al-related OH-bands, however, are subordinate or not observed at all in the spodumene-bearing system, which suggests that OH-vibrations do not reflect absolute Li-contents in quartz due to efficient coupled substitution involving Al. Data from experimental runs and natural specimens indicate that the B-related OH-band can be used as a rough proxy for

Statistical evaluation of potential damage to the Al(OH)3 layer on nTiO2 particles in the presence of swimming pool and seawater

International Nuclear Information System (INIS)

Virkutyte, Jurate; Al-Abed, Souhail R.

2012-01-01

Nanosized TiO 2 particles (nTiO 2 ) are usually coated with an Al(OH) 3 layer when used in sunscreen to shield against the harmful effects of free radicals that are generated when these particles are exposed to UV radiation. Therefore, it is vital to insure the structural stability of these particles in the environment where the protective layer may be damaged and adverse health and environmental effects can occur. This study utilized X-ray analysis (SEM–EDS) to provide a qualitative and semi-quantitative assessment of the chemical and physical characteristics of Al(OH) 3 -coated original and damaged nTiO 2 particles (used in sunscreen lotion formulations) in the presence of both swimming pool and seawater. Also, by utilizing statistical tools, a distribution of Al/Ti (%) on the particle surface was determined and evaluated. It was found that 45 min of treatment with swimming pool and seawater significantly induced the redistribution of Al/Ti (%), which changed the surface characteristics of particles and, therefore, may have induced undesired photo-activity and the consequent formation of free radicals.

Synthesis and properties of A{sub 6}B{sub 2}(OH){sub 16}Cl{sub 2}.4H{sub 2}O (A = Mg, Ni, Zn, Co, Mn and B = Al, Fe) materials for environmental applications

Energy Technology Data Exchange (ETDEWEB)

Dias, Anderson, E-mail: anderson_dias@iceb.ufop.br [Departamento de Quimica, Universidade Federal de Ouro Preto, Campus Morro do Cruzeiro, ICEB II, Sala 67, Ouro Preto-MG, 35400-000 (Brazil); Cunha, Lumena; Vieira, Andiara C. [Departamento de Quimica, Universidade Federal de Ouro Preto, Campus Morro do Cruzeiro, ICEB II, Sala 67, Ouro Preto-MG, 35400-000 (Brazil)

2011-09-15

Highlights: {yields} A{sub 6}B{sub 2}(OH){sub 16}Cl{sub 2}.4H{sub 2}O (A = Mg, Ni, Zn, Co, Mn and B = Al, Fe) materials were synthesized. {yields} Chemical synthesis produced different levels of crystallinity and ordering degree. {yields} Structural investigation by Raman scattering revealed a complex band structure. {yields} A strong correlation between band structure and ionic radius was determined. -- Abstract: Double layered hydroxide materials of composition A{sub 6}B{sub 2}(OH){sub 16}Cl{sub 2}.4H{sub 2}O (A = Mg, Ni, Zn, Co, Mn and B = Al, Fe) were synthesized by chemical precipitation at 60 {sup o}C. Different levels of crystallinity and ordering degree were observed depending upon the chemical environment or the combination between divalent and trivalent cations. The results from high-resolution transmission electron microscopy revealed that nanostructured layered samples were obtained with interplanar spacing compatible with previous literature. Raman scattering was employed to investigate the complex band structure observed, particularly the lattice vibrations at lower frequencies, which is intimately correlated to the cationic radius of both divalent and trivalent ions. The results showed that strongly coordinated water and chloride ions besides highly structured hydroxide layers have a direct influence on the stability of the hydrotalcites. It was observed that transition and decomposition temperatures varied largely for different chemical compositions.

Raman spectra from very concentrated aqueous NaOH and from wet and dry, solid, and anhydrous molten, LiOH, NaOH, and KOH.

Science.gov (United States)

Walrafen, George E; Douglas, Rudolph T W

2006-03-21

High-temperature, high-pressure Raman spectra were obtained from aqueous NaOH solutions up to 2NaOHH2O, with X(NaOH)=0.667 at 480 K. The spectra corresponding to the highest compositions, X(NaOH)> or =0.5, are dominated by H3O2-. An IR xi-function dispersion curve for aqueous NaOH, at 473 K and 1 kbar, calculated from the data of Franck and Charuel indicates that the OH- ion forms H3O2- by preferential H bonding with nonhydrogen-bonded OH groups. Raman spectra from wet to anhydrous, solid LiOH, NaOH, and KOH yield sharp, symmetric OH- stretching peaks at 3664, 3633, and 3596 cm(-1), respectively, plus water-related, i.e., H3O2-, peaks near LiOH, 3562 cm(-1), NaOH, 3596 cm(-1), and, KOH, 3500 cm(-1). Absence of H3O2- peaks from the solid assures that the corresponding melt is anhydrous. Raman spectra from the anhydrous melts yield OH- stretching peak frequencies: LiOH, 3614+/-4 cm(-1), 873 K; NaOH, 3610+/-2 cm(-1), 975 K; and, KOH, 3607+/-2 cm(-1), 773 K, but low-frequency asymmetry due to ion-pair interactions is present which is centered near 3550 cm(-1). The ion-pair-related asymmetry corresponds to the sole IR maximum near 3550 cm(-1) from anhydrous molten NaOH, at 623 K. Bose-Einstein correction of published low-frequency Raman data from molten LiOH revealed an acoustic phonon, near 205 cm(-1), related to restricted translation of OH- versus Li+, and an optical phonon, at 625 cm(-1) and tau approximately 0.05 ps, due to protonic precession and/or pendular motion. Strong H bonding between water and the O atom of OH- forms H3O2-, but the proton of OH- does not bond with H significantly. Large Raman bandwidths (aqueous solutions) are explained in terms of inhomogeneous broadening due to proton transfer in a double well. Vibrational assignments are presented for H3O2-.

OH radio lines in comets - a review

International Nuclear Information System (INIS)

Gerard, E.

1987-01-01

A review of OH cometary radioastronomy from the excitation of the molecule to the detailed analysis of the line profile is presented. It is suggested that the inversion models of Despois et al. (1981) and Schleicher (1983) may be improved by taking the production rates from recent UV data (when the inversion modulus is small) once the radio vs UV discrepancies are better understood. OH radiation transfer through the coma is considered. The unresolved total integrated flux density of the OH coma can be determined by carefully mapping the OH coma using a point source calibrator. The SYMCOMET method for improving the SNR of existing profiles (in order to achieve early detections) has the advantage of suppressing the antisymmetric part of the baseline ripples or instrumental profiles. 24 references

Characterization of Ti6Al7Nb alloy foams surface treated in aqueous NaOH and CaCl2 solutions.

Science.gov (United States)

Bütev, Ezgi; Esen, Ziya; Bor, Şakir

2016-07-01

Ti6Al7Nb alloy foams having 53-73% porosity were manufactured via evaporation of magnesium space holders. A bioactive 1µm thick sodium hydrogel titanate layer, NaxH2-xTiyO2y+1, formed after 5M NaOH treatment, was converted to crystalline sodium titanate, Na2TiyO2y+1, as a result of post-heat treatment. On the other hand, subsequent CaCl2 treatment of NaOH treated specimens induced calcium titanate formation. However, heat treatment of NaOH-CaCl2 treated specimens led to the loss of calcium and disappearance of the titanate phase. All of the aforementioned surface treatments reduced yield strengths due to the oxidation of the cell walls of the foams, while elastic moduli remained mostly unchanged. Accordingly, equiaxed dimples seen on the fracture surfaces of as-manufactured foams turned into relatively flat and featureless fracture surfaces after surface treatments. On the other hand, Ca- and Na-rich coating preserved their mechanical stabilities and did not spall during fracture. The relation between mechanical properties of foams and macro-porosity fraction were found to obey a power law. The foams with 63 and 73% porosity met the desired biocompatibility requirements with fully open pore structures and elastic moduli similar to that of bone. In vitro tests conducted in simulated body fluid (SBF) showed that NaOH-heat treated surfaces exhibit the highest bioactivity and allow the formation of Ca-P rich phases having Ca/P ratio of 1.3 to form within 5 days. Although Ca-P rich phases formed only after 15 days on NaOH-CaCl2 treated specimens, the Ca/P ratio was closer to that of apatite found in bone. Copyright © 2016 Elsevier Ltd. All rights reserved.

Oxalate molecule as the trap for gamma-irradiation energy in the amorphous aluminosilicate Al2(OH)6H4SiO4

International Nuclear Information System (INIS)

Nothig-Laslo, V.; Horvath, L.; Bilinski, H.

1990-01-01

Paramagnetic species which were the products of gamma irradiation at 77 K and at room temperature were studied by ESR spectroscopy in the amorphous aluminosilicate, Al2(OH)6H4SiO4, prepared in the presence and in the absence of oxalate ion. The aluminosilicate precipitated from the solution containing the oxalate ion in 10(-4) mol dm-3 concentration contained the oxalate only in trace amounts. When gamma-irradiated at 77 K and at room temperature, this compound gave the stable paramagnetic species represented by the single ESR line centered at g = 2.000. We ascribe this spectrum to the CO2- radical formed from the oxalate ion. The same aluminosilicate prepared in the absence of the oxalate either produced no stable paramagnetic product after gamma irradiation at room temperature or resulted in composite ESR spectra, indicating the presence of several paramagnetic species if irradiated at 77 K. Complex ESR spectra were transformed by heating to the stable paramagnetic centers which differed from the one obtained from oxalate ion. We conclude that in Al2(OH)6H4SiO4 oxalate acts as a trap for the gamma-radiation energy

Statistical evaluation of potential damage to the Al(OH){sub 3} layer on nTiO{sub 2} particles in the presence of swimming pool and seawater

Energy Technology Data Exchange (ETDEWEB)

Virkutyte, Jurate [Pegasus Technical Services, Inc (United States); Al-Abed, Souhail R., E-mail: al-abed.souhail@epa.gov [U.S. Environmental Protection Agency, National Risk Management Research Laboratory (United States)

2012-03-15

Nanosized TiO{sub 2} particles (nTiO{sub 2}) are usually coated with an Al(OH){sub 3} layer when used in sunscreen to shield against the harmful effects of free radicals that are generated when these particles are exposed to UV radiation. Therefore, it is vital to insure the structural stability of these particles in the environment where the protective layer may be damaged and adverse health and environmental effects can occur. This study utilized X-ray analysis (SEM-EDS) to provide a qualitative and semi-quantitative assessment of the chemical and physical characteristics of Al(OH){sub 3}-coated original and damaged nTiO{sub 2} particles (used in sunscreen lotion formulations) in the presence of both swimming pool and seawater. Also, by utilizing statistical tools, a distribution of Al/Ti (%) on the particle surface was determined and evaluated. It was found that 45 min of treatment with swimming pool and seawater significantly induced the redistribution of Al/Ti (%), which changed the surface characteristics of particles and, therefore, may have induced undesired photo-activity and the consequent formation of free radicals.

Crystal structure and magnetism of Fe2(OH)[B2O4(OH)

DEFF Research Database (Denmark)

Kurayoshi, Yotaro; Hara, Shigeo; Sato, Hirohiko

2014-01-01

The structure and magnetism of Fe2(OH)[B2O4(OH)] are reported. Powder x-ray diffraction reveals a characteristic structure containing two crystallographically independent zigzag-ladder chains of magnetic Fe2+ ions. Magnetization measurements reveal a phase transition at 85 K, below which a weak...... spontaneous magnetization (approximate to 0.15 μB/Fe) appears. Below 85 K, magnetization increases with decreasing temperature down to 70 K, below which it decreases and approaches a constant value at low temperature. The Mossbauer spectrum at room temperature is composed of two paramagnetic doublets...... corresponding to the two crystallographic Fe2+ sites. Below 85 K, each doublet undergoes further splitting because of the magnetic hyperfine fields. The temperature dependence of the hyperfine field is qualitatively different for the two distinguishable Fe2+ sites. This is responsible for the anomalous...

Total OH reactivity study from VOC photochemical oxidation in the SAPHIR chamber

Science.gov (United States)

Yu, Z.; Tillmann, R.; Hohaus, T.; Fuchs, H.; Novelli, A.; Wegener, R.; Kaminski, M.; Schmitt, S. H.; Wahner, A.; Kiendler-Scharr, A.

2015-12-01

It is well known that hydroxyl radicals (OH) act as a dominant reactive species in the degradation of VOCs in the atmosphere. In recent field studies, directly measured total OH reactivity often showed poor agreement with OH reactivity calculated from VOC measurements (e.g. Nölscher et al., 2013; Lu et al., 2012a). This "missing OH reactivity" is attributed to unaccounted biogenic VOC emissions and/or oxidation products. The comparison of total OH reactivity being directly measured and calculated from single component measurements of VOCs and their oxidation products gives us a further understanding on the source of unmeasured reactive species in the atmosphere. This allows also the determination of the magnitude of the contribution of primary VOC emissions and their oxidation products to the missing OH reactivity. A series of experiments was carried out in the atmosphere simulation chamber SAPHIR in Jülich, Germany, to explore in detail the photochemical degradation of VOCs (isoprene, ß-pinene, limonene, and D6-benzene) by OH. The total OH reactivity was determined from the measurement of VOCs and their oxidation products by a Proton Transfer Reaction Time of Flight Mass Spectrometer (PTR-TOF-MS) with a GC/MS/FID system, and directly measured by a laser-induced fluorescence (LIF) at the same time. The comparison between these two total OH reactivity measurements showed an increase of missing OH reactivity in the presence of oxidation products of VOCs, indicating a strong contribution to missing OH reactivity from uncharacterized oxidation products.

Statistical Evaluation of Potential Damage to the Al(OH)3 Layer on nTiO2 Particles in the Presence of Swimming Pool and Seawater

Science.gov (United States)

Nanosized TiO2 particles (nTiO2) are usually coated with an Al(OH)3 layer when used in sunscreen to shield against the harmful effects of free radicals that are generated when these particles are exposed to UV radiation. Therefore, it is vital to ...

New nighttime retrievals of O(3P) and OH densities in the mesosphere/lower thermosphere using SABER/TIMED observations

Science.gov (United States)

Panka, P.; Kutepov, A. A.; Kalogerakis, K. S.; Janches, D.; Feofilov, A.; Rezac, L.; Marsh, D. R.; Yigit, E.

2017-12-01

We present first retrievals of O(3P) and OH densities in the mesosphere/lower thermosphere (MLT) using SABER/TIMED OH 2.0 and 1.6 μm limb emission observations. Recently, Kaufmann et al. [2014] reported that current SABER O(3P) densities are on average 30% higher compared to other observations. In this study we applied new detailed non-LTE model [Panka et al. 2017] of nighttime OH(v), which accounts for the new mechanism OH(v≥5)+O(3P)→O(1D)+OH(v-5) of energy transfer recently suggested by Sharma et al. [2015] and confirmed through laboratory studies by Kalogerakis et al. [2016]. Based on this model we developed a new self-consistent two channel retrieval approach for O(3P) and OH density. Using this approach, we retrieved O(3P) densities that are 10-40% lower than current SABER O(3P), as well as total OH density which is retrieved for the first time using SABER observations. We compare our retrieveals with the results of other observations and models. As it was recently shown by Panka et al. [2017], the new mechanism of OH quenching produces a significant pumping of CO2 4.3 µm emission. We discuss the effects these new O(3P) and OH retrievals have on the nighttime CO2 density retrievals from the SABER 4.3 µm channel.

Compatibility of hydrogarnet, Ca3Al2(SiO4)x(OH)4(3−x), with sulfate and carbonate-bearing cement phases: 5–85 °C

International Nuclear Information System (INIS)

Okoronkwo, Monday Uchenna; Glasser, Fredrik Paul

2016-01-01

The stable existence of hydrogarnet in Portland cement compositions cured at temperatures below 55 °C has long been predicted from application of equilibrium thermodynamics. However hydrogarnet is not often reported in hydrated commercial Portland cements. The substitutions (SO 4 –CO 3 –OH) in AFm have previously been shown to stabilise AFm to higher temperatures and raise the temperature at which AFm converts to Si-free hydrogarnet, C 3 AH 6 . But unanswered question remains about the compatibility of AFm and AFm solid solutions with Si-substituted hydrogarnet, Ca 3 Al 2 (SiO 4 ) x (OH) 4(3 − x) . Phase relations of C 3 AH 6 and Ca 3 Al 2 (SiO 4 ) x (OH) 4(3 − x) at sulfate and carbonate activities conditioned respectively by (gypsum and SO 4 -AFt) and (calcite and CO 3 -AFt) have been determined experimentally in the range 5–85 °C. The results confirm the instability of Si-free hydrogarnet with carbonate and sulfate-bearing cement phases, but do indicate that a range of silica-substituted hydrogarnet solid solutions are stable under conditions likely to be encountered in blended cement systems.

Synthesis and investigation of aluminium uranium-containing compounds of Al[B5UO6]2[OH]·nH2O (B5=P, As) composition

International Nuclear Information System (INIS)

Chernorukov, N.G.; Sulejmanov, E.V.; Barch, S.V.

2001-01-01

The technique of synthesis of hydroxyuranophosphate and hydroxyuranoarsenate of aluminium is developed. Hydroxyuranophosphates and hydroxyuranoarsenates of aluminium are prepared by reaction of interaction of aqueous solutions of orthophosphoric (orthoarsenic) acid (0.05 mol/l), uranyl nitrate (0.05 mol/l) and aluminium nitrate (0.1 mol/l) at 20 Deg C. Peculiarities of the structure and thermal degradation reactions are studied by the methods of x-ray diffraction, IR spectroscopy, thermography. It is shown that in dependence on outer conditions in the systems Al[PUO 6 ] 2 ·[OH]·nH 2 O and Al[AsUO 6 ] 2 ·[OH]·nH 2 O crystal hydrates with hydrate numbers n=3-11(13) and anhydrous compounds form. The compounds have laminated type of lattice. Two-dimensional layers of [P(As)UO 6 ] ∞ n- are the basis of anion sublattice of these compounds. Aluminium in coordination surrounding of hydroxy groups and water molecules forms cationic sublattice [ru

Completing the Heterocubane Family [Cp*AlE]4 (E = O, S, Se, and Te) by Selective Oxygenation and Sulfuration of [Cp*Al]4: Density Functional Theory Calculations of [Cp*AlE]4 and Reactivity of [Cp*AlO]4 toward Hydrolysis.

Science.gov (United States)

Stelzer, Adrian C; Hrobárik, Peter; Braun, Thomas; Kaupp, Martin; Braun-Cula, Beatrice

2016-05-16

The subvalent aluminum compound [Cp*Al]4 (1) reacts with dioxygen, N2O, or sulfur to yield the heterocubane complexes [Cp*AlX]4 [X = O (2) and S (3)]. Treatment of [Cp*AlO]4 (2) with (tBuO)3SiOH gave [(tBuO)3SiOAlO]4 (6) and Cp*H. The structures and spectroscopic data of the Al clusters are supported by density functional theory (DFT) calculations, which also demonstrate the importance of noncovalent interactions (NCI) in oligomeric Al(I) complexes as well as in [Cp*AlS]4 and the heavier homologues of Se and Te. The computed (27)Al NMR shifts indicate a deshielding at the Al centers with increasing electronegativity of the chalcogen atom as well as significant spin-orbit shielding effects within the heavier heterocubane [Al4E4] cores. Further hydrolysis of 6 with an additional amount of silanol in the presence of water resulted in the formation of [Al4(OH)6(OH2)2(OSiOtBu3)6] (7), which shows a structural motif found in boehmite and diaspore.

Enhancing anaerobic digestion of waste activated sludge by the combined use of NaOH and Mg(OH)2: Performance evaluation and mechanism study.

Science.gov (United States)

Huang, Cheng; Lai, Jia; Sun, Xiuyun; Li, Jiansheng; Shen, Jinyou; Han, Weiqing; Wang, Lianjun

2016-11-01

In this study, the combination treatment of NaOH and Mg(OH)2 was applied to anaerobic digestion of waste activated sludge (WAS) for simultaneously enhancement of volatile fatty acids (VFAs) production, nutrients removal and sludge dewaterability. The maximum VFAs production (461mg COD/g VSS) was obtained at the NaOH/Mg(OH)2 ratio of 75:25, which was much higher than that of the blank or sole NaOH. Moreover, nutrients removal and sludge dewaterability were improved by the combined using of NaOH and Mg(OH)2. Mechanism investigations revealed that the presence of Mg(OH)2 could maintain alkaline environment, which contributed to inhibit the activity of methanogens. Also, the bridging between Mg(2+) and extracellular polymeric substances (EPS) plays an important role in the solubilization and dewatering of sludge. High-throughput sequencing analysis demonstrated that the abundance of bacteria involved in sludge hydrolysis and VFAs accumulation was greatly enriched with the mixtures of NaOH and Mg(OH)2. Copyright © 2016 Elsevier Ltd. All rights reserved.

Solid-state 27Al and 29Si NMR investigations on Si-substituted hydrogarnets

International Nuclear Information System (INIS)

Rivas Mercury, J.M.; Pena, P.; Aza, A.H. de; Turrillas, X.; Sobrados, I.; Sanz, J.

2007-01-01

Partially deuterated Ca 3 Al 2 (SiO 4 ) 3-x (OH) 4x hydrates prepared by a reaction in the presence of D 2 O of synthetic tricalcium aluminate with different amounts of amorphous silica were characterized by 29 Si and 27 Al magic-angle spinning nuclear magnetic resonance (NMR) spectroscopy. The 29 Si NMR spectroscopy was used for quantifying the non-reacted silica and the resulting hydrated products. The incorporation of Si into Ca 3 Al 2 (SiO 4 ) 3-x (OH) 4x was followed by 27 Al NMR spectroscopy: Si:OH ratios were determined quantitatively from octahedral Al signals ascribed to Al(OH) 6 and Al(OSi)(OH) 5 environments. The NMR data obtained were consistent with the concentrations of the Al and Si species deduced from transmission electron microscopy energy-dispersive spectrometry and Rietveld analysis of both X-ray and neutron diffraction data

Solid-state 27Al and 29Si NMR characterization of hydrates formed in calcium aluminate-silica fume mixtures

International Nuclear Information System (INIS)

Pena, P.; Rivas Mercury, J.M.; Aza, A.H. de; Turrillas, X.; Sobrados, I.; Sanz, J.

2008-01-01

Partially deuterated Ca 3 Al 2 (SiO 4 ) y (OH) 12-4y -Al(OH) 3 mixtures, prepared by hydration of Ca 3 Al 2 O 6 (C 3 A), Ca 12 Al 14 O 33 (C 12 A 7 ) and CaAl 2 O 4 (CA) phases in the presence of silica fume, have been characterized by 29 Si and 27 Al magic-angle spinning-nuclear magnetic resonance (MAS-NMR) spectroscopies. NMR spectroscopy was used to characterize anhydrous and fully hydrated samples. In hydrated compounds, Ca 3 Al 2 (OH) 12 and Al(OH) 3 phases were detected. From the quantitative analysis of 27 Al NMR signals, the Al(OH) 3 /Ca 3 Al 2 (OH) 12 ratio was deduced. The incorporation of Si into the katoite structure, Ca 3 Al 2 (SiO 4 ) 3-x (OH) 4x , was followed by 27 Al and 29 Si NMR spectroscopies. Si/OH ratios were determined from the quantitative analysis of 27 Al MAS-NMR components associated with Al(OH) 6 and Al(OSi)(OH) 5 environments. The 29 Si NMR spectroscopy was also used to quantify the unreacted silica and amorphous calcium aluminosilicate hydrates formed, C-S-H and C-A-S-H for short. From 29 Si NMR spectra, the amount of Si incorporated into different phases was estimated. Si and Al concentrations, deduced by NMR, transmission electron microscopy, energy dispersive spectrometry, and Rietveld analysis of both X-ray and neutron data, indicate that only a part of available Si is incorporated in katoite structures. - Graphical abstract: Transmission electron micrograph of CaAl 2 O 4 -microsilica mixture hydrated at 90 deg. C for 31 days showing a cubic Ca 3 Al 2.0±0.2 (SiO 4 ) 0.9±0.2 (OH) 1.8 crystal surrounded by unreacted amorphous silica spheres

Crystal structure of vanuralite, Al[(UO{sub 2}){sub 2}(VO{sub 4}){sub 2}](OH) . 8.5H{sub 2}O

Energy Technology Data Exchange (ETDEWEB)

Plasil, Jakub [Czech Academy of Sciences, Praha (Czech Republic). Inst. of Physics

2017-07-01

Vanuralite, Al[(UO{sub 2}){sub 2}(VO{sub 4}){sub 2}](OH) . 8.5H{sub 2}O, is a rare supergene uranyl vanadate that forms during hydration-oxidation weathering of uraninite in oxide zones of U deposits. On the basis of single-crystal X-ray diffraction data it is monoclinic, space group P2{sub 1}/n, with a = 10.4637(10), b = 8.4700(5), c = 20.527(2) Aa, β = 102.821(9) , V=1773.9(3) Aa{sup 3} and Z = 4, D{sub calc.} = 3.561 g cm{sup -3}. The structure of vanuralite (R = 0.058 for 2638 unique observed reflections) contains uranyl vanadate sheets of francevillite topology of the composition [(UO{sub 2}){sub 2}(VO{sub 4}){sub 2}]{sup 2-}. Sheets are stacked perpendicular to c, and an interstitial complex {sup [6]}Al(OH)(H{sub 2}O){sub 4}(H{sub 2}O){sub 4.5}; adjacent structural sheets are linked through an extensive network of hydrogen bonds. Vanuralite is the most complex mineral among uranyl vanadates, with 961 bits/cell. The scarcity of occurrences is probably caused by the less common combination of elements present in the structure, as well as the relatively high complexity of the structure (compared to related minerals), arising namely from the complicated network of H-bonds.

The first study of antiferromagnetic eosphorite-childrenite series (Mn{sub 1−x}Fe{sub x})AlP(OH){sub 2}H{sub 2}O (x=0.5)

Energy Technology Data Exchange (ETDEWEB)

Behal, D. [Sektion Kristallographie, Department für Geo- und Umweltwissenschaften, Ludwig-Maximilians-Universität München (LMU), Theresienstrasse 41, D-80333 Munich (Germany); Forschungsneutronenquelle Heinz Maier-Leibnitz (FRM II), Technische Universität München (TUM), Lichtenbergstrasse 1, D-85748 Garching (Germany); Röska, B. [Sektion Kristallographie, Department für Geo- und Umweltwissenschaften, Ludwig-Maximilians-Universität München (LMU), Theresienstrasse 41, D-80333 Munich (Germany); Park, S.-H., E-mail: sohyun.park@lmu.de [Sektion Kristallographie, Department für Geo- und Umweltwissenschaften, Ludwig-Maximilians-Universität München (LMU), Theresienstrasse 41, D-80333 Munich (Germany); Pedersen, B. [Forschungsneutronenquelle Heinz Maier-Leibnitz (FRM II), Technische Universität München (TUM), Lichtenbergstrasse 1, D-85748 Garching (Germany); Benka, G.; Pfleiderer, Ch. [Chair E21, Physik-Department, Technische Universität München (TUM), James-Franck-Strasse 1, D-85748 Garching (Germany); Wakabayashi, Y.; Kimura, T. [Division of Materials Physics, Graduate School of Engineering Science, Osaka University, Toyonaka 560-8531 (Japan)

2017-04-15

This study presents for the first time the antiferromagnetic structure of the eosphorite-childrenite series (Mn{sub 1-x}Fe{sub x})AlPO{sub 4}(OH){sub 2}H{sub 2}O (x=0.5), based on neutron single crystal diffraction at 3 K in combination with group theoretical representation analysis. The new magnetic structure is described in the magnetic space group P{sub C}mnb, maintaining the atomistic unit cell size (a×b×c) with a ~6.9 Å, b ~10.4 Å, c ~13.4 Å. Mn-rich and Fe-rich zones within solid solution crystals are expanded up to several hundred micrometers, as seen in electron microprobe and polarisation microscopy. Magnetic susceptibility and specific heat measurements on two different eosphorite-childrenite crystals show the magnetic transition temperature between 6.5 K and 6.8 K as the Mn{sup 2+}/Fe{sup 2+} ratio varies over single compositional zones. Below the Néel temperature, a magnetic field between 1.5 T and 2 T parallel to the a-axis causes a 180° spin-flip, reaching the saturation (5.25 μ{sub B} pfu) toward high magnetic fields. - Highlights: • New magnetic structure of (Mn{sub 1-x}Fe{sub x})AlPO{sub 4}(OH){sub 2}H{sub 2}O (x=0.5). • Magnetic phase transition at 6.5–6.6 K. • Magnetic interaction anisotropy in (Mn{sub 0.5}Fe{sub 0.5})AlPO{sub 4}(OH){sub 2}H{sub 2}O. • Compositional zones in the eosphorite-childrenite series.

MERLIN observations of the OH/IR stars OH 53.6-0.2, OH 138.0+7.2 and OH 141.7+3.5

International Nuclear Information System (INIS)

Chapman, J.; Cohen, R.J.; Norris, R.P.; Diamond, P.J.; Booth, R.S.

1984-01-01

OH maser emission from the three OH/IR stars OH 53.6-0.2, OH 138.0+7.2 and OH 141.7+3.5 has been mapped with an angular resolution of 0.28 arcsec and a velocity resolution of 0.7 km s -1 using the Jodrell Bank MERLIN array. Maps are presented of the 1612-MHz OH emission over individual velocity ranges. The maps are consistent with a uniform expanding shell model, and by fitting such models to the data the angular diameters of the shells have been estimated to an accuracy of approx. 25 per cent. (author)

Thermoluminescent properties of polycrystalline carbon doped LaAlO3/La(OH)3 crystals synthesized by solid state reaction for application in UV dosimetry

International Nuclear Information System (INIS)

Alves, N.; Oliveira de F, L.; Barbosa F, W.

2017-10-01

It is well known that UV radiation can induce certain deleterious effects, such as erythema, painful inflammation of the membrane of the eye and skin cancer. Therefore, it has been pushing the research for producing new and high performance UV sensitive Tl materials. There is an increasing interest in the development of new Tl materials for ultraviolet (UV) dosimetry purposes, owing to simplicity of the sample readout compared to other techniques. In this paper, thermoluminescence and dosimetric characteristics of pure and carbon doped lanthanum aluminate and hydroxide lanthanum crystals, irradiated with different UV doses, were studied and discussed. All samples studied were produced by solid state reaction method with different mixing methodologies. Characterization of sintered powders by X-ray diffraction, UV-Vis spectrophotometry and Ftir spectroscopy were performed. XRD data confirmed the LaAlO 3 and La(OH) 3 crystalline phases. The thermoluminescent study revealed that all compositions presented high UV sensibility. The sample which was grown by first sintering La 2 O 3 together carbon atoms and then sintering again in order to obtain La 2 O 3 :C together Al 2 O 3 , presented the best linear dose response over UV doses ranging from 0.042 to 0.63 mJ/cm 2 , with correlation coefficients equal to 0.99931. The synthesis methodology used was very efficient to obtain crystals with high Tl output intensities for low exposure rate UV R fields. (Author)

Continuous Flow Aerobic Alcohol Oxidation Reactions Using a Heterogeneous Ru(OH)x/Al2O3 Catalyst

Science.gov (United States)

2015-01-01

Ru(OH)x/Al2O3 is among the more versatile catalysts for aerobic alcohol oxidation and dehydrogenation of nitrogen heterocycles. Here, we describe the translation of batch reactions to a continuous-flow method that enables high steady-state conversion and single-pass yields in the oxidation of benzylic alcohols and dehydrogenation of indoline. A dilute source of O2 (8% in N2) was used to ensure that the reaction mixture, which employs toluene as the solvent, is nonflammable throughout the process. A packed bed reactor was operated isothermally in an up-flow orientation, allowing good liquid–solid contact. Deactivation of the catalyst during the reaction was modeled empirically, and this model was used to achieve high conversion and yield during extended operation in the aerobic oxidation of 2-thiophene methanol (99+% continuous yield over 72 h). PMID:25620869

Corrosion Resistance of the Superhydrophobic Mg(OH2/Mg-Al Layered Double Hydroxide Coatings on Magnesium Alloys

Directory of Open Access Journals (Sweden)

Fen Zhang

2016-04-01

Full Text Available Coatings of the Mg(OH2/Mg-Al layered double hydroxide (LDH composite were formed by a combined co-precipitation method and hydrothermal process on the AZ31 alloy substrate in alkaline condition. Subsequently, a superhydrophobic surface was successfully constructed to modify the composite coatings on the AZ31 alloy substrate using stearic acid. The characteristics of the composite coatings were investigated by means of X-ray diffractometer (XRD, Fourier transform infrared spectroscopy (FTIR, X-ray photoelectron spectroscopy (XPS, scanning electronic microscope (SEM and contact angle (CA. The corrosion resistance of the coatings was assessed by potentiodynamic polarization, the electrochemical impedance spectrum (EIS, the test of hydrogen evolution and the immersion test. The results showed that the superhydrophobic coatings considerably improved the corrosion resistant performance of the LDH coatings on the AZ31 alloy substrate.

First-principles investigations of Ni3Al(111) and NiAl(110) surfaces at metal dusting conditions

DEFF Research Database (Denmark)

Saadi, Souheil; Hinnemann, Berit; Appel, Charlotte C.

2011-01-01

We investigate the structure and surface composition of the γ′-Ni3Al(111) and β-NiAl(110) alloy surfaces at conditions relevant for metal dusting corrosion related to catalytic steam reforming of natural gas. In regular service as protective coatings, nickel–aluminum alloys are protected...... by an oxide scale, but in case of oxide scale spallation, the alloy surface may be directly exposed to the reactive gas environment and vulnerable to metal dusting. By means of density functional theory and thermochemical calculations for both the Ni3Al and NiAl surfaces, the conditions under which CO and OH...... adsorption is to be expected and under which it is inhibited, are mapped out. Because CO and OH are regarded as precursors for nucleating graphite or oxide on the surfaces, phase diagrams for the surfaces provide a simple description of their stability. Specifically, this study shows how the CO and OH...

VLA OH Zeeman Observations of the NGC 6334 Complex Source A

Science.gov (United States)

Mayo, E. A.; Sarma, A. P.; Troland, T. H.; Abel, N. P.

2004-12-01

We present a detailed analysis of the NGC 6334 complex source A, a compact continuum source in the SW region of the complex. Our intent is to determine the significance of the magnetic field in the support of the surrounding molecular cloud against gravitational collapse. We have performed OH 1665 and 1667 MHz observations taken with the Very Large Array in the BnA configuration and combined these data with the lower resolution CnB data of Sarma et al. (2000). These observations reveal magnetic fields with values of the order of 350 μ G toward source A, with maximum fields reaching 500 μ G. We have also theoretically modeled the molecular cloud surrounding source A using Cloudy, with the constraints to the model based on observation. This model provides significant information on the density of H2 through the cloud and also the relative density of H2 to OH which is important to our analysis of the region. We will combine the knowledge gained through the Cloudy modeling with Virial estimates to determine the significance of the magnetic field to the dynamics and evolution of source A.

Solid-state {sup 27}Al and {sup 29}Si NMR investigations on Si-substituted hydrogarnets

Energy Technology Data Exchange (ETDEWEB)

Rivas Mercury, J.M. [Instituto de Ceramica y Vidrio, CSIC, Kelsen, 5, 28049 Cantoblanco-Madrid (Spain); Pena, P. [Instituto de Ceramica y Vidrio, CSIC, Kelsen, 5, 28049 Cantoblanco-Madrid (Spain)]. E-mail: ppena@icv.csic.es; Aza, A.H. de [Instituto de Ceramica y Vidrio, CSIC, Kelsen, 5, 28049 Cantoblanco-Madrid (Spain); Turrillas, X. [Instituto de Ciencias de la Construccion Eduardo Torroja, CSIC, Serrano Galvache, 4, 28033 Madrid (Spain); Sobrados, I. [Instituto de Ciencia de Materiales, CSIC, Sor Juana Ines de la Cruz, 3, 28049 Cantoblanco-Madrid (Spain); Sanz, J. [Instituto de Ciencia de Materiales, CSIC, Sor Juana Ines de la Cruz, 3, 28049 Cantoblanco-Madrid (Spain)

2007-02-15

Partially deuterated Ca{sub 3}Al{sub 2}(SiO{sub 4}){sub 3-x}(OH){sub 4x} hydrates prepared by a reaction in the presence of D{sub 2}O of synthetic tricalcium aluminate with different amounts of amorphous silica were characterized by {sup 29}Si and {sup 27}Al magic-angle spinning nuclear magnetic resonance (NMR) spectroscopy. The {sup 29}Si NMR spectroscopy was used for quantifying the non-reacted silica and the resulting hydrated products. The incorporation of Si into Ca{sub 3}Al{sub 2}(SiO{sub 4}){sub 3-x}(OH){sub 4x} was followed by {sup 27}Al NMR spectroscopy: Si:OH ratios were determined quantitatively from octahedral Al signals ascribed to Al(OH){sub 6} and Al(OSi)(OH){sub 5} environments. The NMR data obtained were consistent with the concentrations of the Al and Si species deduced from transmission electron microscopy energy-dispersive spectrometry and Rietveld analysis of both X-ray and neutron diffraction data.

An i.r. investigation on some calcium aluminate hydrates, Ca2Al(OH)6+X-.yH2O (= 3CaO.Al2O3.CaX2.nH2O, X- = univalent anion)

NARCIS (Netherlands)

Houtepen, C.J.M.; Stein, H.N.

1976-01-01

The i.r. spectra of some hydrated and dehydrated calcium aluminate hydrates of the type Ca2Al(OH)6+X-·yH2O with X- = Cl-, Br-, J-, ClO3-, NO3-, ClO4- (y = 2) and X- = BrO3-, JO3- (2

Bulk modulus of basic sodalite, Na8[AlSiO4]6(OH)2·2H2O, a possible zeolitic precursor in coal-fly-ash-based geopolymers

KAUST Repository

Oh, Jae Eun; Moon, Juhyuk; Mancio, Mauricio; Clark, Simon M.; Monteiro, Paulo J.M.

2011-01-01

Synthetic basic sodalite, Na8[AlSiO4] 6(OH)2•2H2O, cubic, P43n, (also known as hydroxysodalite hydrate) was prepared by the alkaline activation of amorphous aluminosilicate glass, obtained from the phase separation of Class F fly ash. The sample

Enhanced emission of encaged-OH--free Ca12(1-x)Sr12xAl14O33:0.1%Gd3+ conductive phosphors via tuning the encaged-electron concentration for low-voltage FEDs.

Science.gov (United States)

Zhang, Meng; Liu, Yuxue; Yang, Jian; Zhu, Hancheng; Yan, Duanting; Zhang, Xinyang; Liu, Chunguang; Xu, Changshan; Zhang, Hong

2017-05-24

Encaged-OH - -free Ca 12(1-x) Sr 12x Al 14 O 33 :0.1%Gd 3+ conductive phosphors were prepared through a melt-solidification process in combination with a subsequent heat treatment. Absorption spectra showed that the maximum encaged-electron concentration was increased to 1.08 × 10 21 cm -3 through optimizing the doping amount of Sr 2+ (x = 0.005). Meanwhile, FTIR and Raman spectra indicated that pure Ca 11.94 Sr 0.06 Al 14 O 33 :0.1%Gd 3+ conductive phosphor without encaged OH - and C 2 2- anions was acquired. For the conductive powders heat-treated in air for different times, the encaged-electron concentrations were tuned from 1.02 × 10 21 to 8.3 × 10 20 cm -3 . ESR, photoluminescence, and luminescence kinetics analyses indicated that the emission at 312 nm mainly originated from Gd 3+ ions surrounded by encaged O 2- anions, while Gd 3+ ions surrounded by encaged electrons had a negative contribution to the UV emission due to the existence of an energy transfer process. Under low-voltage electron-beam excitation (3 kV), enhanced cathodoluminescence (CL) of the conductive phosphors could be achieved by tuning the encaged-electron concentrations. In particular, for the encaged-OH - -free conductive phosphor, the emission intensity of the CL was about one order of magnitude higher than that of the conductive phosphor containing encaged OH - anions. Our results suggested that the encaged-OH - -free conductive phosphors have potential application in low-voltage FEDs.

Canted antiferromagnetism in KNi3[PO3(F,OH)]2[PO2(OH)2]F2 with a stair-case Kagomé lattice

Science.gov (United States)

Liu, Li-Chen; Ren, Wei-Jian; Huang, Ya-Xi; Pan, Yuanming; Mi, Jin-Xiao

2017-10-01

A new nickel phosphate KNi3[PO3(F,OH)]2[PO2(OH)2]F2 has been synthesized using a modified hydrothermal method. Structural characterizations show that it adopts a 3D framework structure with 2D layers of Ni octahedra in a stair-case Kagomé lattice. The Ni2 octahedron at the inversion center shares two trans-faces with Ni1 octahedra to form a linear trimer (Ni3O8F6) as the basic structural unit. The Ni-trimers are linked between themselves by sharing F-corners and to [PO3(F,OH)] tetrahedral groups by sharing O-corners to form 2D stair-case Kagomé layers, which are parallel to the (100) plane and are stacked along the a-axis. Successive Kagomé layers are combined together by [PO2(OH)2] tetrahedral groups and interstice cations K+. Magnetic measurements reveal that KNi3[PO3(F,OH)]2[PO2(OH)2]F2 exhibits a canted antiferromagnetic ordering with a ferromagnetic component at low temperatures.

A combined high-temperature experimental and theoretical kinetic study of the reaction of dimethyl carbonate with OH radicals

KAUST Repository

Khaled, Fathi; Giri, Binod; Szőri, Milá n; Mai, Tam V.-T.; Huynh, Lam K.; Farooq, Aamir

2017-01-01

The reaction kinetics of dimethyl carbonate (DMC) and OH radicals were investigated behind reflected shock waves over the temperature range of 872-1295 K and at pressures near 1.5 atm. Reaction progress was monitored by detecting OH radicals at 306.69 nm using a UV laser absorption technique. The rate coefficients for the reaction of DMC with OH radicals were extracted using a detailed kinetic model developed by Glaude et al. (Proc. Combust. Inst. 2005, 30(1), 1111-1118). The experimental rate coefficients can be expressed in Arrhenius form as: kexpt'l = 5.15 × 10(13) exp(-2710.2/T) cm(3) mol(-1) s(-1). To explore the detailed chemistry of the DMC + OH reaction system, theoretical kinetic analyses were performed using high-level ab initio and master equation/Rice-Ramsperger-Kassel-Marcus (ME/RRKM) calculations. Geometry optimization and frequency calculations were carried out at the second-order Møller-Plesset (MP2) perturbation level of theory using Dunning's augmented correlation consistent-polarized valence double-ζ basis set (aug-cc-pVDZ). The energy was extrapolated to the complete basis set using single point calculations performed at the CCSD(T)/cc-pVXZ (where X = D, T) level of theory. For comparison purposes, additional ab initio calculations were also carried out using composite methods such as CBS-QB3, CBS-APNO, G3 and G4. Our calculations revealed that the H-abstraction reaction of DMC by OH radicals proceeds via an addition elimination mechanism in an overall exothermic process, eventually forming dimethyl carbonate radicals and H2O. Theoretical rate coefficients were found to be in excellent agreement with those determined experimentally. Rate coefficients for the DMC + OH reaction were combined with literature rate coefficients of four straight chain methyl ester + OH reactions to extract site-specific rates of H-abstraction from methyl esters by OH radicals.

Origin of the OH vibrational blue shift in the LiOH crystal.

Science.gov (United States)

Hermansson, Kersti; Gajewski, Grzegorz; Mitev, Pavlin D

2008-12-25

The O-H vibrational frequency in crystalline hydroxides is either upshifted or downshifted by its crystalline surroundings. In the LiOH crystal, the experimental gas-to-solid O-H frequency upshift ("blue shift") is approximately +115 cm(-1). Here plane-wave DFT calculations for the isotope-isolated LiOH crystal have been performed and we discuss the origin of the OH frequency upshift, and the nature of the OH group and the interlayer interactions. We find that (1) the vibrational frequency upshift originates from interactions within the LiOH layer; this OH upshift is slightly lessened by the interlayer interactions; (2) the interlayer O-H - - - H-O interaction is largely electrostatic in character (but there is no hydrogen bonding); (3) the gas-to-solid vibrational shift for OH in LiOH(s) and its subsystems qualitatively adheres to a parabola-like "frequency vs electric field strength" correlation curve, which has a maximum for a positive electric field, akin to the correlation curve earlier found in the literature for an isolated OH(-) ion in an electric field.

Synthesis and characterization of β-Ni(OH)2 up grown nanoflakes by SILAR method

International Nuclear Information System (INIS)

Kulkarni, S.B.; Jamadade, V.S.; Dhawale, D.S.; Lokhande, C.D.

2009-01-01

In this paper we report a 'bottom up' approach to synthesize β-Ni(OH) 2 nanoflakes using novel successive ionic layer adsorption and reaction (SILAR) method. Ni(OH) 2 thin films have been deposited on glass substrate using aqueous alkaline nickel chloride as nickel ion source and double distilled water maintained at 353 K temperature as hydroxyl ion source. The structural, surface morphological, optical and electrical properties of films are examined. The nanocrystallinity and β-phase of Ni(OH) 2 are confirmed by X-ray diffraction and FT-IR studies. Scanning electron microscope study revealed microporous and random distribution of well up grown interlocked nanoflakes. Optical absorption studies show wide optical band gap of 3.26 eV for β-Ni(OH) 2 . The electrical properties revealed that β-Ni(OH) 2 has negative temperature coefficient of resistance with p-type semiconducting behaviour. The electrochemical property studied by cyclic voltametry in 2 M KOH electrolyte solution revealed pseudo capacitive behaviour, when β-Ni(OH) 2 thin film employed as working electrode in three electrode electrochemical cell with platinum as counter electrode and saturated calomel as reference electrode. The specific capacitance of 350 F g -1 is obtained with nanoflake like morphology.

Revealing microstructure and dislocation behavior in BAlN/AlGaN heterostructures

KAUST Repository

Sun, Haiding; Wu, Feng; Park, Young Jae; Al tahtamouni, T. M.; Liao, Che-Hao; Guo, Wenzhe; Alfaraj, Nasir; Li, Kuang-Hui; Anjum, Dalaver H.; Detchprohm, Theeradetch; Dupuis, Russell D.; Li, Xiaohang

2017-01-01

We reveal the microstructure and dislocation behavior in 20-pair B0.14Al0.86N/Al0.70Ga0.30N multiple-stack heterostructures (MSHs) exhibiting an increasing dislocation density along the c-axis, which is attributed to the continuous generation of dislocations (edge and mixed-type) within the individual B0.14Al0.86N layers. At the MSH interfaces, the threading dislocations were accompanied by a string of V-shape pits extending to the surface, leading to interface roughening and the formation of surface columnar features. Strain maps indicated an approximately 1.5% tensile strain and 1% compressive strain in the B0.14Al0.86N and Al0.70Ga0.30N layers, respectively. Twin structures were observed, and the MSH eventually changed from monocrystalline to polycrystalline.

Revealing microstructure and dislocation behavior in BAlN/AlGaN heterostructures

KAUST Repository

Sun, Haiding

2017-12-18

We reveal the microstructure and dislocation behavior in 20-pair B0.14Al0.86N/Al0.70Ga0.30N multiple-stack heterostructures (MSHs) exhibiting an increasing dislocation density along the c-axis, which is attributed to the continuous generation of dislocations (edge and mixed-type) within the individual B0.14Al0.86N layers. At the MSH interfaces, the threading dislocations were accompanied by a string of V-shape pits extending to the surface, leading to interface roughening and the formation of surface columnar features. Strain maps indicated an approximately 1.5% tensile strain and 1% compressive strain in the B0.14Al0.86N and Al0.70Ga0.30N layers, respectively. Twin structures were observed, and the MSH eventually changed from monocrystalline to polycrystalline.

Managing OHS

DEFF Research Database (Denmark)

Hull Kristensen, Peer

2011-01-01

Contrary to a widely held view, rather than seeing the certification of Occupational Health and Safety (OHS) as a barrier to increasing employee participation, this article views new ways of structuring participation as a necessary step towards making improvements in OHS management systems....... The article first considers how work organization has changed and then in a similar way traces how bargaining has shifted from being distributive to become integrative to create a fundamental change in the negotiation regime. Finally, by analyzing an OHS-certified firm in greater depth, the article shows how...... solutions for improvements in OHS management and notable bottom-up formulations of OHS benchmarks may help us discover how the organizational form of firms with high-performance work organization can be developed through new participatory structures....

Attikaite, Ca3Cu2Al2(AsO4)4(OH)4 · 2H2O, a new mineral species

Science.gov (United States)

Chukanov, N. V.; Pekov, I. V.; Zadov, A. E.

2007-12-01

Attikaite, a new mineral species, has been found together with arsenocrandalite, arsenogoyazite, conichalcite, olivenite, philipsbornite, azurite, malachite, carminite, beudantite, goethite, quartz, and allophane at the Christina Mine No. 132, Kamareza, Lavrion District, Attiki Prefecture (Attika), Greece. The mineral is named after the type locality. It forms spheroidal segregations (up to 0.3 mm in diameter) consisting of thin flexible crystals up to 3 × 20 × 80 μm in size. Its color is light blue to greenish blue, with a pale blue streak. The Mohs’ hardness is 2 to 2.5. The cleavage is eminent mica-like parallel to {001}. The density is 3.2(2) g/cm3 (measured in heavy liquids) and 3.356 g/cm3 (calculated). The wave numbers of the absorption bands in the infrared spectrum of attikaite are (cm-1; sh is shoulder; w is a weak band): 3525 sh, 3425, 3180, 1642, 1120 w, 1070 w, 1035 w, 900 sh, 874, 833, 820, 690 w, 645 w, 600 sh, 555, 486, 458, and 397. Attikaite is optically biaxial, negative, α = 1.642(2), β = γ = 1.644(2) ( X = c) 2 V means = 10(8)°, and 2 V calc = 0°. The new mineral is microscopically colorless and nonpleochroic. The chemical composition (electron microprobe, average over 4 point analyses, wt %) is: 0.17 MgO, 17.48 CaO, 0.12 FeO, 16.28 CuO, 10.61 Al2O3, 0.89 P2O5, 45.45 As2O5, 1.39 SO3, and H2O (by difference) 7.61, where the total is 100.00. The empirical formula calculated on the basis of (O,OH,H2O)22 is: Ca2.94Cu{1.93/2+} Al1.97Mg0.04Fe{0.02/2+} [(As3.74S0.16P0.12)Σ4.02O16.08](OH)3.87 · 2.05H2 O. The simplified formula is Ca3Cu2Al2(AsO4)4(OH)4 · 2H2O. Attikaite is orthorhombic, space group Pban, Pbam or Pba2; the unit-cell dimensions are a = 10.01(1), b = 8.199(5), c = 22.78(1) Å, V = 1870(3) Å3, and Z = 4. In the result of the ignition of attikaite for 30 to 35 min at 128 140°, the H2O bands in the IR spectrum disappear, while the OH-group band is not modified; the weight loss is 4.3%, which approximately corresponds to two H2O

Thermoluminescent properties of polycrystalline carbon doped LaAlO{sub 3}/La(OH){sub 3} crystals synthesized by solid state reaction for application in UV dosimetry

Energy Technology Data Exchange (ETDEWEB)

Alves, N.; Oliveira de F, L. [Federal University of the State of Minas Gerais, Department of Nuclear Engineering, Av. Pres. Antonio Carlos 6627, 31270-901 Belo Horizonte, Minas Gerais (Brazil); Barbosa F, W., E-mail: neire.radiologia@yahoo.com.br [Nuclear Technology Development Center, 941, 30161-970 Belo Horizonte, Minas Gerais (Brazil)

2017-10-15

It is well known that UV radiation can induce certain deleterious effects, such as erythema, painful inflammation of the membrane of the eye and skin cancer. Therefore, it has been pushing the research for producing new and high performance UV sensitive Tl materials. There is an increasing interest in the development of new Tl materials for ultraviolet (UV) dosimetry purposes, owing to simplicity of the sample readout compared to other techniques. In this paper, thermoluminescence and dosimetric characteristics of pure and carbon doped lanthanum aluminate and hydroxide lanthanum crystals, irradiated with different UV doses, were studied and discussed. All samples studied were produced by solid state reaction method with different mixing methodologies. Characterization of sintered powders by X-ray diffraction, UV-Vis spectrophotometry and Ftir spectroscopy were performed. XRD data confirmed the LaAlO{sub 3} and La(OH){sub 3} crystalline phases. The thermoluminescent study revealed that all compositions presented high UV sensibility. The sample which was grown by first sintering La{sub 2}O{sub 3} together carbon atoms and then sintering again in order to obtain La{sub 2}O{sub 3}:C together Al{sub 2}O{sub 3}, presented the best linear dose response over UV doses ranging from 0.042 to 0.63 mJ/cm{sup 2}, with correlation coefficients equal to 0.99931. The synthesis methodology used was very efficient to obtain crystals with high Tl output intensities for low exposure rate UV R fields. (Author)

Assay of 25-OH vitamin D3

International Nuclear Information System (INIS)

Nayer, P. de; Thalasso, M.; Beckers, C.

1977-01-01

A simplified version of the competitive protein binding assay for 25-OH vit D3 derived from the method of Belsey et al. is presented. The procedure does not include a chromatography step, and is performed on an alcoolic extract of 0.1 ml plasma or serum. Normal rat serum (1:20,000) was used as binding protein. No β-lipoproteins were added to the assay buffer. A 10% displacement of the tracer was observed at 0.04 ng/tube, and 50% at 0.15 ng/tube, allowing for the measurement of 25-OH vit D3 concentrations between 2 ng/ml and 200 ng/ml. Mean values in a normal group was 23.1 +- 6.5 ng/ml (range 16-37 ng/ml, n = 11). (orig.) [de

Properties of B4C–PbO–Al(OH)3-epoxy nanocomposite prepared by ultrasonic dispersion approach for high temperature neutron shields

International Nuclear Information System (INIS)

Lee, M.K.; Lee, J.K.; Kim, J.W.; Lee, G.J.

2014-01-01

High functional epoxy nanocomposites with three different filler materials, i.e., B 4 C, PbO, and Al(OH) 3 , were fabricated using an effective fabrication method consisting of an ultrasonic dispersion of nanoparticles in low-viscosity hardener and a subsequent mixing of a hardener-nanoparticle colloid with epoxy resins. It was confirmed that this approach provided not only an uniform dispersion but also an excellent wetting with enhanced interfacial adhesion of nano-particulate fillers within the matrix. By incorporating those three fillers, a synergistic effect was verified in multiple properties such as mechanical strength properties, thermal degradation, flame retardancy, and radiation shielding performance

Replacement of Oxygen by Sulfur in Small Organic Molecules. 3. Theoretical Studies on the Tautomeric Equilibria of the 2OH and 4OH-Substituted Oxazole and Thiazole and the 3OH and 4OH-Substituted Isoxazole and Isothiazole in the Isolated State and in Solution

Directory of Open Access Journals (Sweden)

Peter I. Nagy

2016-07-01

Full Text Available This follow-up paper completes the author’s investigations to explore the in-solution structural preferences and relative free energies of all OH-substituted oxazole, thiazole, isoxazole, and isothiazole systems. The polarizable continuum dielectric solvent method calculations in the integral-equation formalism (IEF-PCM were performed at the DFT/B97D/aug-cc-pv(q+(dz level for the stable neutral tautomers with geometries optimized in dichloromethane and aqueous solution. With the exception of the predictions for the predominant tautomers of the 3OH isoxazole and isothiazole, the results of the IEF-PCM calculations for identifying the most stable tautomer of the given species in the two selected solvents agreed with those from experimental investigations. The calculations predict that the hydroxy proton, with the exception for the 4OH isoxazole and 4OH isothiazole, moves preferentially to the ring nitrogen or to a ring carbon atom in parallel with the development of a C=O group. The remaining, low-fraction OH tautomers will not be observable in the equilibrium compositions. Relative solvation free energies obtained by the free energy perturbation method implemented in Monte Carlo simulations are in moderate accord with the IEF-PCM results, but consideration of the ΔGsolv/MC values in calculating ΔGstot maintains the tautomeric preferences. It was revealed from the Monte Carlo solution structure analyses that the S atom is not a hydrogen-bond acceptor in any OH-substituted thiazole or isothiazole, and the OH-substituted isoxazole and oxazole ring oxygens may act as a weak hydrogen-bond acceptor at most. The molecules form 1.0−3.4 solute−water hydrogen bonds in generally unexplored numbers at some specific solute sites. Nonetheless, hydrogen-bond formation is favorable with the NH, C=O and OH groups.

XPS, TEM and NRA investigations of Zn(Se,OH)/Zn(OH){sub 2} films on Cu(In,Ga)(S,Se){sub 2} substrates for highly efficient solar cells

Energy Technology Data Exchange (ETDEWEB)

Eisele, W.; Ennaoui, A.; Schubert-Bischoff, P.; Giersig, M.; Pettenkofer, C.; Krauser, J.; Lux-Steiner, M. [Hahn-Meitner Inst., Berlin (Germany); Zweigart, S.; Karg, F. [Siemens and Shell Solar, Munich (Germany)

2003-01-01

Structural and compositional properties of Zn(Se,OH)/Zn(OH){sub 2} buffer layers deposited by chemical bath deposition(CBD) on Cu(In,Ga)(S,Se){sub 2} (CIGSS) absorbers are investigated. Due to the aqueous nature of the CBD process, oxygen and hydrogen were incorporated into the 'ZnSe' buffer layer mainly in the form of Zn(OH){sub 2} as is shown by X-ray photoelectron spectroscopy and nuclear reaction analysis (NRA) measurements leading to the nomenclature 'Zn(Se,OH)'. Prior to the deposition of Zn(Se,OH), a zinc treatment of the absorber was performed. During that treatment a layer mainly consisting of Zn(OH){sub 2} grew to a thickness of several nanometer. The whole buffer layer therefore consists of a Zn(Se,OH)/Zn(OH){sub 2} structure on CIGSS. Part of the Zn(OH){sub 2} in both layers (i.e. the Zn(Se,OH) and the Zn(OH){sub 2} layer) might be converted into ZnO during measurements or storage. Scanning electron microscopy pictures showed that a complete coverage of the absorber with the buffer layer was achieved. Transmission electron microscopy revealed the different regions of the buffer layer: An amorphous area (possibly Zn(OH){sub 2}) and a partly nanocrystalline area, where lattice planes of ZnSe could be identified. Solar cell efficiencies of ZnO/Zn(Se,OH)/Zn(OH){sub 2}/CIGSS devices exceed 14% (total area).(author)

Synthesis and characterization of non halogen fire retardant composite through combination of epoxy resin, Al(OH)3 additive and filler

Science.gov (United States)

Saputra, Asep Handaya; Sungkar, Faraj

2017-11-01

Epoxy has a wide range of applications in many sectors, but it still has deficiency in fire retardancy. Therefore, it is combined with fire retardant additives. Fire retardant additive commonly contains halogen compounds that causes environmental and health problems. Therefore Al (OH)3 additive is used to improve the fire retardancy properties of composite through decomposition that produced water vapour and formation of oxide layer on its surface. In this research, synthesis of fire retardant composite has been conducted by varying filler carbon black and silica (1%, 2.5%, 5%, 7.5%, 10%wt) with composition of Al (OH)3 50%wt and epoxy 50%wt. Fire retardancy of composite was observed by UL-94V standard, while thermal degradation behaviour of composite was analyzed by thermal gravimetric analysis and differential scanning calorimetry. Whereas, mechanical properties was studied based on its tensile strength and hardness. It was found that the best concentration for carbon black and silica is 1%wt and 2.5%wt respectively. The addition of carbon black 1%wt and silica 2.5%wt could improve the flame retardancy and gives V-0 flammability rating. Besides that, the addition of carbon black 1%wt is able to increase the thermal stability of composite by reducing mass loss rate until 10.75%/minute and total mass loss until 53.76%. While adding silica 2.5%wt could also enhance its thermal stability by decreasing mass loss rate until 9.32%/minute and total mass loss until 51.06%. Furthermore, the addition of carbon black and silica could decrease its tensile strength and hardness. The addition of carbon black 1%wt yields composite with 6.59 MPa for tensile strength and 65.8 shore D for hardness. Whereas the addition of of silica 2.5%wt produces composite with the tensile strength up to 9.89MPa and hardness up to71.2 shore D.

AN ARECIBO SURVEY FOR ZEEMAN SPLITTING IN OH MEGAMASER GALAXIES

International Nuclear Information System (INIS)

McBride, James; Heiles, Carl

2013-01-01

We present the results of a comprehensive survey using the Arecibo Observatory for Zeeman splitting of OH lines in OH megamasers (OHMs). A total of 77 sources were observed with the Arecibo telescope. Of these, maser emission could not be detected for eight sources, and two sources were only ambiguously detected. Another 27 sources were detected at low signal-to-noise ratios or with interference that prevented placing any useful limits on the presence of magnetic fields. In 26 sources, it was possible to place upper limits on the magnitude of magnetic fields, typically between 10 and 30 mG. For 14 sources, the Stokes V spectra exhibit features consistent with Zeeman splitting. Eleven of these 14 are new detections, and the remaining three are re-detections of Stokes V detections in Robishaw et al. Among confident new detections, we derive magnetic fields associated with maser regions with magnitudes ranging from 6.1 to 27.6 mG. The distribution of magnetic field strengths suggests the magnetic fields in OH masing clouds in OHMs are larger than those in Galactic OH masers. The results are consistent with magnetic fields playing a dynamically important role in OH masing clouds in OHMs.

The Recovery of Uranium From The Rejected Fuel Plate Dispersion Type of U3O8-Al and U3Si2Al by NaOH

International Nuclear Information System (INIS)

Widodo, G; Aji, D

1998-01-01

The recovery of uranium from the rejected fuel plate dispersion type of U 3 O 8 -AI And U 3 Si 2 -AI with a dissolution has been performed.Each of 5 fragment of fuel plate dispersion of U 3 O 8 -AI or U 3 Si 2 Al of 1x4 cm size was put in the distilled glass content of 250 ml NaOH solution whit The concentration variation 10,15,20,25,and 30%,and than was heated at temperature of 102 o C and was stirred constantly by magnetic stirred.Uranium in the form of U 3 O 8 or U 3 Si 2 was separated by filtration and Either residu and filtrate was analyzed by potentiometry using modified Devies Gray method. From the experiment data it was found in the residu that presentation of uranium was 83.99-84.05% and 84.67-86.556% while in filtrate it was found 53.90 ppm and 69.3 ppm

Elasticity of phase-Pi (Al3Si2O7(OH)3) - A hydrous aluminosilicate phase

Science.gov (United States)

Peng, Ye; Mookherjee, Mainak; Hermann, Andreas; Bajgain, Suraj; Liu, Songlin; Wunder, Bernd

2017-08-01

Phase-Pi (Al3Si2O7(OH)3) is an aluminosilicate hydrous mineral and is likely to be stable in hydrated sedimentary layers of subducting slabs. Phase-Pi is likely to be stable between the depths of 60 and 200 km and is likely to transport water into the Earth's interior. Here, we use first principles simulations based on density functional theory to explore the crystal structure at high-pressure, equation of state, and full elastic stiffness tensor as a function of pressure. We find that the pressure volume results could be described by a finite strain fit with V0 , K0 , and K0‧ being 310.3 Å3, 133 GPa, and 3.6 respectively. At zero pressure, the full elastic stiffness tensor shows significant anisotropy with the diagonal principal components C11 , C22 , and C33 being 235, 292, 266 GPa respectively, the diagonal shear C44 , C55 , and C66 being 86, 92, and 87 GPa respectively, and the off-diagonal stiffness C12 , C13 , C14 ,C15 , C16 , C23 , C24 , C25 , C26 , C34 , C35 , C36 , C45 , C46 , and C56 being 73, 78, 6, -30, 15, 61, 17, 2, 1, -13, -15, 6, 3, 1, and 3 GPa respectively. The zero pressure, shear modulus, G0 and its pressure derivative, G0 ‧ are 90 GPa and 1.9 respectively. Upon compression, hydrogen bonding in phase-Pi shows distinct behavior, with some hydrogen bonds weakening and others strengthening. The latter eventually undergo symmetrization, at pressure greater (>40 GPa) than the thermodynamic stability of phase-Pi. Full elastic constant tensors indicate that phase-Pi is very anisotropic with AVP ∼22.4% and AVS ∼23.7% at 0 GPa. Our results also indicate that the bulk sound velocity of phase-Pi is slower than that of the high-pressure hydrous aluminosilicate phase, topaz-OH.

Mechanochemical synthesis of Cu-Al and methyl orange intercalated Cu-Al layered double hydroxides

International Nuclear Information System (INIS)

Qu, Jun; He, Xiaoman; Chen, Min; Hu, Huimin; Zhang, Qiwu; Liu, Xinzhong

2017-01-01

In this study, a mechanochemical route to synthesize a Cu-Al layered double hydroxide (LDH) and a methyl orange (MO) intercalated one (MO-LDH) was introduced, in which basic cupric carbonate (Cu_2(OH)_2CO_3) and aluminum hydroxide (Al(OH)_3) with Cu/Al molar ratio at 2/1 was first dry ground for 2 h and then agitated in water or methyl orange solution for another 4 h to obtain the LDH and MO-LDH products without any heating operation. The prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Thermogravimetry (TG), Differential scanning calorimetry (DSC) and Scanning electron microscopy (SEM). The products showed high crystallinity phase of Cu-Al and MO intercalated Cu-Al LDH with no evident impurities, proving that the craft introduced here was facile and effective. The new idea can be applied in other fields to produce organic-inorganic composites. - Highlights: • A facile mechanochemical route to synthesize Cu-Al and MO intercalated Cu-Al LDH. • The products possesses high crystalline of LDH phase with no impure phases. • The dry milling process induces the element substitution between the raw materials. • The agitation operation helps the grain growth of LDH.

Mechanochemical synthesis of Cu-Al and methyl orange intercalated Cu-Al layered double hydroxides

Energy Technology Data Exchange (ETDEWEB)

Qu, Jun, E-mail: forsjun@whut.edu.cn [School of Resources and Environmental Engineering, Wuhan University of Technology, Luoshi Road 122, Wuhan, Hubei 430070 (China); He, Xiaoman; Chen, Min; Hu, Huimin [School of Resources and Environmental Engineering, Wuhan University of Technology, Luoshi Road 122, Wuhan, Hubei 430070 (China); Zhang, Qiwu, E-mail: zhangqw@whut.edu.cn [School of Resources and Environmental Engineering, Wuhan University of Technology, Luoshi Road 122, Wuhan, Hubei 430070 (China); Liu, Xinzhong [College of Ecological Environment and Urban Construction, Fujian University of Technology, Fuzhou 350118 China (China)

2017-04-15

In this study, a mechanochemical route to synthesize a Cu-Al layered double hydroxide (LDH) and a methyl orange (MO) intercalated one (MO-LDH) was introduced, in which basic cupric carbonate (Cu{sub 2}(OH){sub 2}CO{sub 3}) and aluminum hydroxide (Al(OH){sub 3}) with Cu/Al molar ratio at 2/1 was first dry ground for 2 h and then agitated in water or methyl orange solution for another 4 h to obtain the LDH and MO-LDH products without any heating operation. The prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Thermogravimetry (TG), Differential scanning calorimetry (DSC) and Scanning electron microscopy (SEM). The products showed high crystallinity phase of Cu-Al and MO intercalated Cu-Al LDH with no evident impurities, proving that the craft introduced here was facile and effective. The new idea can be applied in other fields to produce organic-inorganic composites. - Highlights: • A facile mechanochemical route to synthesize Cu-Al and MO intercalated Cu-Al LDH. • The products possesses high crystalline of LDH phase with no impure phases. • The dry milling process induces the element substitution between the raw materials. • The agitation operation helps the grain growth of LDH.

Redetermination of eveite, Mn2AsO4(OH, based on single-crystal X-ray diffraction data

Directory of Open Access Journals (Sweden)

Yongbo W. Yang

2011-12-01

Full Text Available The crystal structure of eveite, ideally Mn2(AsO4(OH [dimanganese(II arsenate(V hydroxide], was refined from a single crystal selected from a co-type sample from Långban, Filipstad, Varmland, Sweden. Eveite, dimorphic with sarkinite, is structurally analogous with the important rock-forming mineral andalusite, Al2OSiO4, and belongs to the libethenite group. Its structure consists of chains of edge-sharing distorted [MnO4(OH2] octahedra (..2 symmetry extending parallel to [001]. These chains are cross-linked by isolated AsO4 tetrahedra (..m symmetry through corner-sharing, forming channels in which dimers of edge-sharing [MnO4(OH] trigonal bipyramids (..m symmetry are located. In contrast to the previous refinement from Weissenberg photographic data [Moore & Smyth (1968. Am. Mineral. 53, 1841–1845], all non-H atoms were refined with anisotropic displacement parameters and the H atom was located. The distance of the donor and acceptor O atoms involved in hydrogen bonding is in agreement with Raman spectroscopic data. Examination of the Raman spectra for arsenate minerals in the libethenite group reveals that the position of the peak originating from the O—H stretching vibration shifts to lower wavenumbers from eveite, to adamite, zincolivenite, and olivenite.

OH vibrational activation and decay dynamics of CH4-OH entrance channel complexes

International Nuclear Information System (INIS)

Wheeler, Martyn D.; Tsiouris, Maria; Lester, Marsha I.; Lendvay, Gyoergy

2000-01-01

Infrared spectroscopy has been utilized to examine the structure and vibrational decay dynamics of CH 4 -OH complexes that have been stabilized in the entrance channel to the CH 4 +OH hydrogen abstraction reaction. Rotationally resolved infrared spectra of the CH 4 -OH complexes have been obtained in the OH fundamental and overtone regions using an IR-UV (infrared-ultraviolet) double-resonance technique. Pure OH stretching bands have been identified at 3563.45(5) and 6961.98(4) cm-1 (origins), along with combination bands involving the simultaneous excitation of OH stretching and intermolecular bending motions. The infrared spectra exhibit extensive homogeneous broadening arising from the rapid decay of vibrationally activated CH 4 -OH complexes due to vibrational relaxation and/or reaction. Lifetimes of 38(5) and 25(3) ps for CH 4 -OH prepared with one and two quanta of OH excitation, respectively, have been extracted from the infrared spectra. The nascent distribution of the OH products from vibrational predissociation has been evaluated by ultraviolet probe laser-induced fluorescence measurements. The dominant inelastic decay channel involves the transfer of one quantum of OH stretch to the pentad of CH 4 vibrational states with energies near 3000 cm-1. The experimental findings are compared with full collision studies of vibrationally excited OH with CH 4 . In addition, ab initio electronic structure calculations have been carried out to elucidate the minimum energy configuration of the CH 4 -OH complex. The calculations predict a C 3v geometry with the hydrogen of OH pointing toward one of four equivalent faces of the CH 4 tetrahedron, consistent with the analysis of the experimental infrared spectra. (c) 2000 American Institute of Physics

Synthesis, characterization and properties of a glycol-coordinated ε-Keggin-type Al13 chloride

KAUST Repository

Gu, Bin; Sun, Chenglin; Fettinger, James C.; Casey, William H.; Dikhtiarenko, Alla; Gascon, Jorge; Koichumanova, Kamila; Babu Sai Sankar Gupta, Karthick; Jan Heeres, Hero; He, Songbo

2018-01-01

Herein we present the first example of a glycol-coordinated ε-Keggin Al13 chloride (gl-ε-Al13), which is the first chelated version since discovery of Al13 in 1960. The molecular structure consists of [AlO4Al12(OH)12(OC2H4OH)12]Cl7·H2O units with chelating mono-anionic ethylene glycol units replacing one bridging and one terminal oxygen site.

Synthesis, characterization and properties of a glycol-coordinated ε-Keggin-type Al13 chloride

KAUST Repository

Gu, Bin

2018-03-29

Herein we present the first example of a glycol-coordinated ε-Keggin Al13 chloride (gl-ε-Al13), which is the first chelated version since discovery of Al13 in 1960. The molecular structure consists of [AlO4Al12(OH)12(OC2H4OH)12]Cl7·H2O units with chelating mono-anionic ethylene glycol units replacing one bridging and one terminal oxygen site.

A combined high-temperature experimental and theoretical kinetic study of the reaction of dimethyl carbonate with OH radicals

KAUST Repository

Khaled, Fathi

2017-02-08

The reaction kinetics of dimethyl carbonate (DMC) and OH radicals were investigated behind reflected shock waves over the temperature range of 872-1295 K and at pressures near 1.5 atm. Reaction progress was monitored by detecting OH radicals at 306.69 nm using a UV laser absorption technique. The rate coefficients for the reaction of DMC with OH radicals were extracted using a detailed kinetic model developed by Glaude et al. (Proc. Combust. Inst. 2005, 30(1), 1111-1118). The experimental rate coefficients can be expressed in Arrhenius form as: kexpt\\'l = 5.15 × 10(13) exp(-2710.2/T) cm(3) mol(-1) s(-1). To explore the detailed chemistry of the DMC + OH reaction system, theoretical kinetic analyses were performed using high-level ab initio and master equation/Rice-Ramsperger-Kassel-Marcus (ME/RRKM) calculations. Geometry optimization and frequency calculations were carried out at the second-order Møller-Plesset (MP2) perturbation level of theory using Dunning\\'s augmented correlation consistent-polarized valence double-ζ basis set (aug-cc-pVDZ). The energy was extrapolated to the complete basis set using single point calculations performed at the CCSD(T)/cc-pVXZ (where X = D, T) level of theory. For comparison purposes, additional ab initio calculations were also carried out using composite methods such as CBS-QB3, CBS-APNO, G3 and G4. Our calculations revealed that the H-abstraction reaction of DMC by OH radicals proceeds via an addition elimination mechanism in an overall exothermic process, eventually forming dimethyl carbonate radicals and H2O. Theoretical rate coefficients were found to be in excellent agreement with those determined experimentally. Rate coefficients for the DMC + OH reaction were combined with literature rate coefficients of four straight chain methyl ester + OH reactions to extract site-specific rates of H-abstraction from methyl esters by OH radicals.

Vibrational Dynamics of Interfacial Water by Free Induction Decay Sum Frequency Generation (FID-SFG) at the Al2O3(1120)/H2O Interface.

Science.gov (United States)

Boulesbaa, Abdelaziz; Borguet, Eric

2014-02-06

The dephasing dynamics of a vibrational coherence may reveal the interactions of chemical functional groups with their environment. To investigate this process at a surface, we employ free induction decay sum frequency generation (FID-SFG) to measure the time that it takes for free OH stretch oscillators at the charged (pH ≈ 13, KOH) interface of alumina/water (Al2O3/H2O) to lose their collective coherence. By employing noncollinear optical parametric amplification (NOPA) technology and nonlinear vibrational spectroscopy, we showed that the single free OH peak actually corresponds to two distinct oscillators oriented opposite to each other and measured the total dephasing time, T2, of the free OH stretch modes at the Al2O3/H2O interface with a sub-40 fs temporal resolution. Our results suggested that the free OH oscillators associated with interfacial water dephase on the time scale of 89.4 ± 6.9 fs, whereas the homogeneous dephasing of interfacial alumina hydroxyls is an order of magnitude slower.

Thermal OH Emission, A New Tracer for Galaxy Structure: Z-Thickness and Rolling Motion of the Perseus Arm

Science.gov (United States)

Engelke, Philip; Allen, Ronald J.; Hogg, David E.

2016-06-01

Recent observations with the Green Bank Telescope (Allen et al. 2015) have shown that high-sensitivity measurements of OH 18-cm emission can be a useful alternative tracer for the large-scale distribution of molecular gas in the Galactic ISM. This component of the ISM is not well traced by 3-mm CO(1-0) emission. In the quiescent regions examined so far, fewer than half of the OH spectral features found show corresponding CO emission in the CfA survey (Dame el al. 2001). The intensities of the two main-line OH transitions at 1665 and 1667 MHz are in the “thermal” or LTE ratio of 5:9 and emanate from low-opacity gas with a wide spatial distribution similar to the HI. This morphology resembles that of the “dark gas” (or “dark neutral medium”) postulated by Grenier et al. (2005) as the possible source of target nucleii required to explain the excess gamma ray emission from the Galactic ISM. OH 18-cm emission provides a new tool for studies of the quantity, distance, and kinematics of this new CO-dark molecular component of the ISM. As a demonstration of the utility of this new tool, we apply it to two questions about the molecular structure of the Perseus Arm: the thickness in the z-direction, and the rolling motions of the arm discovered in the earliest HI maps of the Galaxy (e.g. Oort 1962, Rougoor 1964). Using OH emission as a molecular tracer, we find that the molecular component of gas in the Perseus Arm has a comparable z-thickness to that measured using HI, although it appears to be clumpier. OH also shows that the molecular component experiences the “rolling motions” known from the HI data. As a molecular tracer, OH allows more regions to be observed than can be observed using CO(1-0), and as an optically-thin emission line, OH can provide direct column density measurements.

Direct Lineage Reprogramming Reveals Disease-Specific Phenotypes of Motor Neurons from Human ALS Patients

Directory of Open Access Journals (Sweden)

Meng-Lu Liu

2016-01-01

Full Text Available Subtype-specific neurons obtained from adult humans will be critical to modeling neurodegenerative diseases, such as amyotrophic lateral sclerosis (ALS. Here, we show that adult human skin fibroblasts can be directly and efficiently converted into highly pure motor neurons without passing through an induced pluripotent stem cell stage. These adult human induced motor neurons (hiMNs exhibit the cytological and electrophysiological features of spinal motor neurons and form functional neuromuscular junctions (NMJs with skeletal muscles. Importantly, hiMNs converted from ALS patient fibroblasts show disease-specific degeneration manifested through poor survival, soma shrinkage, hypoactivity, and an inability to form NMJs. A chemical screen revealed that the degenerative features of ALS hiMNs can be remarkably rescued by the small molecule kenpaullone. Taken together, our results define a direct and efficient strategy to obtain disease-relevant neuronal subtypes from adult human patients and reveal their promising value in disease modeling and drug identification.

Interaction between OHS regulation and OHS certification in Denmark

DEFF Research Database (Denmark)

Hendriksen, Kåre; Jørgensen, Kirsten; Jørgensen, Ulrik

2010-01-01

In 2001, the Danish Parliament approved a law on OHS certification that provided economic support to enterprises/organizations that were certified according to one of the two national OHS standards. These certified enterprises/organizations were also exempt from the initial inspection by the Danish...... Working Environment Authority, which they would otherwise be required to pay for. In practice, this meant that inspection of the certified enterprises was transferred to the certification bodies unless a work accident or work-caused ailment or the like was reported. In 2005, the law was revised so...... certification has existed as a form of substitute inspection for almost 10 years, no systematic evaluation of the effects of OHS certification on the OHS, and thereby the validity of the certificate, has been made. In several cases, however, certified enterprises/organizations have received injunctions...

Hydrogen migration dynamics in hydrated Al clusters: The Al17(−)·H2O system as an example

International Nuclear Information System (INIS)

Álvarez-Barcia, S.; Flores, J. R.

2014-01-01

The Al m (−) ·(H 2 O) n systems are known to undergo water splitting processes in the gas phase giving H k Al m (OH) k (−) ·(H 2 O) n−k systems, which can generate H 2 . The migration of H atoms from one Al atom to another on the cluster's surface is of critical importance to the mechanism of the complete H 2 production process. We have applied a combination of Molecular Dynamics and Rice-Ramsperger-Kassel-Marcus theory including tunneling effects to study the gas-phase evolution of HAl 17 (OH) (−) , which can be considered a model system. First, we have performed an extensive search for local minima and the connecting saddle points using a density functional theory method. It is found that in the water-splitting process Al 17 (−) ·(H 2 O) → HAl 17 (OH) (−) , the H atom which bonds to the Al cluster losses rather quickly its excess energy, which is easily “absorbed” by the cluster because of its flexibility. This fact ultimately determines that long-range hydrogen migration is not a very fast process and that, probably, tunneling only plays a secondary role in the migration dynamics, at least for moderate energies. Reduction of the total energy results in the process being very much slowed down. The consequences on the possible mechanisms of H 2 generation from the interaction of Al clusters and water molecules are discussed

Synthesis and Structural Characterization of a CHA-type AlPO4 Molecular Sieve with Penta-Coordinated Framework Aluminum Atoms.

Science.gov (United States)

Park, Gi Tae; Jo, Donghui; Ahn, Nak Ho; Cho, Jung; Hong, Suk Bong

2017-07-17

The structure-directing effects of a series of polymethylimidazolium cations with different numbers of methyl groups as organic structure-directing agents (OSDAs) in the synthesis of aluminophosphate (AlPO 4 )-based molecular sieves in both fluoride and hydroxide media are investigated. On the one hand, among the OSDAs studied here, the smallest 1,3-dimethylimidazolium and the largest 1,2,3,4,5-pentamethylimidazolium cations were found to direct the synthesis of a new variant of the triclinic chabazite (CHA)-type AlPO 4 material, designated AlPO 4 -34(t) V , and the one-dimensional small-pore silicoaluminophosphate (SAPO) molecular sieve STA-6 in hydroxide media, respectively. On the other hand, the intermediate-sized 1,2,3,4-tetramethylimidazolium cation gave SSZ-51, a two-dimensional large-pore SAPO material, in fluoride media. Synchrotron powder X-ray diffraction and Rietveld analyses reveal that as-made AlPO 4 -34(t) V contains penta-coordinated framework Al species connected by hydroxyl groups, as well as tetrahedral framework Al, which contrasts with the distortions arising from the two F - or OH - bridges between octahedral Al atoms in all already known AlPO 4 -34 materials. The presence of Al-OH-Al linkages in this triclinic AlPO 4 -34 molecular sieve has been further corroborated by thermal analysis, variable-temperature IR,27Al magic-angle spinning NMR, and dispersion-corrected density functional theory calculations.

Overtone spectroscopy of the hydroxyl stretch vibration in hydroxylamine (NH2OH)

International Nuclear Information System (INIS)

Scott, J.L.; Luckhaus, D.; Brown, S.S.; Crim, F.F.

1995-01-01

We present photoacoustic spectra of the second (3ν OH ), third (4ν OH ), and fourth (5ν OH ) overtone bands of the hydroxyl stretch vibration in hydroxylamine. Asymmetric rotor simulations of the rovibrational contours provide rotational constants and an estimate of the homogeneous linewidth. The fourth overtone band appears anomalously broad relative to the two lower bands, reflecting a sharp increase in the rate of intramolecular vibrational energy redistribution (IVR). By contrast, the calculated density of states increases smoothly with energy. The homogeneous linewidth of the fourth overtone transition is similar to that measured by Luo et al. [J. Chem. Phys. 93, 9194 (1990)] for the predissociative sixth overtone band, supporting the conclusion that the broadening arises from increased (ro)vibrational coupling at an energy between the third and fourth overtone states

Theoretical and experimental insights into the ·OH-mediated mineralization mechanism of flutriafol

International Nuclear Information System (INIS)

Liu, Siqi; Zhou, Xiezhen; Han, Weiqing; Li, Jiansheng; Sun, Xiuyun; Shen, Jinyou; Wang, Lianjun

2017-01-01

Highlights: • A complete ·OH-mediated degradation pathway of flutriafol is proposed. • Computational approach is effective to reveal the favorable transformation process. • The electrochemical experiments well verify the theoretical results. - Abstract: Flutriafol is one of the widely used triazole fungicides in global pesticides market, and its degradation mechanisms are important to develop powerful technologies to remove it. Insight into the kinetics and mechanisms of ·OH-mediated mineralization of flutriafol have been obtained using quantum chemical calculation and electrochemical experiment methods. The complete ·OH-mediated degradation pathway of flutriafol was proposed by density functional theory (DFT) simulation and the potential energy surface was mapped out for possible reactions. On the basis of DFT calculations, the optimal ·OH-mediated mineralization mechanism of flutriafol was revealed, and a series of intermediates were observed accumulated in the degradation process, most significance among which were (2-fluorophenyl) (4-fluorophenyl)-Methanone, phenol, dihydroxybenzenes, benzoquinones, muconic acids, maleic acids, oxalic acids and formic acid. To give deeper insight into the ·OH-mediated reaction mechanism, the electrostatic potential (ESP) and average local ionization energy (ALIE) analysis were conducted for o-benzoquinone and p-benzoquinone. The proposed mechanism was further validated by electrochemical experiments at TiO_2-NTs/SnO_2-Sb/PbO_2 anode. The main intermediates were identified and quantified by experimental method, indicating that the proposed ·OH-mediated degradation mechanism derived from DFT calculations was feasible. These detailed findings could be instrumental for a comprehensive understanding of the ·OH-mediated mineralization mechanism of flutriafol and the similar contaminants.

Roymillerite, Pb24Mg9(Si9AlO28)(SiO4)(BO3)(CO3)10(OH)14O4, a new mineral: mineralogical characterization and crystal chemistry

Science.gov (United States)

Chukanov, Nikita V.; Jonsson, Erik; Aksenov, Sergey M.; Britvin, Sergey N.; Rastsvetaeva, Ramiza K.; Belakovskiy, Dmitriy I.; Van, Konstantin V.

2017-11-01

The new mineral roymillerite Pb24Mg9(Si9AlO28)(SiO4)(BO3)(CO3)10(OH)14O4, related to britvinite and molybdophyllite, was discovered in a Pb-rich assemblage from the Kombat Mine, Grootfontein district, Otjozondjupa region, Namibia, which includes also jacobsite, cerussite, hausmannite, sahlinite, rhodochrosite, barite, grootfonteinite, Mn-Fe oxides, and melanotekite. Roymillerite forms platy single-crystal grains up to 1.5 mm across and up to 0.3 mm thick. The new mineral is transparent, colorless to light pink, with a strong vitreous lustre. Cleavage is perfect on (001). Density calculated using the empirical formula is equal to 5.973 g/cm3. Roymillerite is optically biaxial, negative, α = 1.86(1), β ≈ γ = 1.94(1), 2 V (meas.) = 5(5)°. The IR spectrum shows the presence of britvinite-type tetrahedral sheets, {CO}3^{2 - }, {BO}3^{3 - }, and OH- groups. The chemical composition is (wt%; electron microprobe, H2O and CO2 determined by gas chromatography, the content of B2O3 derived from structural data): MgO 4.93, MnO 1.24, FeO 0.95, PbO 75.38, B2O3 0.50, Al2O3 0.74, CO2 5.83, SiO2 7.90, H2O 1.8, total 99.27. The empirical formula based on 83 O atoms pfu (i.e. Z = 1) is Pb24.12Mg8.74Mn1.25Fe0.94B1.03Al1.04C9.46Si9.39H14.27O83. The crystal structure was determined using single-crystal X-ray diffraction data. The new mineral is triclinic, space group P \\bar{1}, with a = 9.315(1), b = 9.316(1), c = 26.463(4) Å, α = 83.295(3)°, β = 83.308(3)°, γ = 60.023(2)°, V = 1971.2(6) Å3. The crystal structure of roymillerite is based built by alternating pyrophyllite-type TOT-modules Mg9(OH)8[(Si,Al)10O28] and I-blocks Pb24(OH)6O4(CO3)10(BO3,SiO4). The strongest lines of the powder X-ray diffraction pattern [ d, Å (I, %) ( hkl)] are: 25.9 (100) (001), 13.1 (11) (002), 3.480 (12) (017, 107, -115, 1-15), 3.378 (14) (126, 216), 3.282 (16) (-2-15, -1-25), 3.185 (12) (-116, 1-16), 2.684 (16) (031, 301, 030, 300, 332, -109, 0-19, 1-18), 2.382 (11) (0.0.-11). Roymillerite is

Treatment of As(V) and As(III) by electrocoagulation using Al and Fe electrode.

Science.gov (United States)

Kuan, W H; Hu, C Y; Chiang, M C

2009-01-01

A batch electrocoagulation (EC) process with bipolar electrode and potentiodynamic polarization tests with monopolar systems were investigated as methods to explore the effects of electrode materials and initial solution pH on the As(V) and As(III) removal. The results displayed that the system with Al electrode has higher reaction rate during the initial period from 0 to 25 minutes than that of Fe electrode for alkaline condition. The pH increased with the EC time because the As(V) and As(III) removal by either co-precipitation or adsorption resulted in that the OH positions in Al-hydroxide or Fe-hydroxide were substituted by As(V) and As(III). The pH in Fe electrode system elevate higher than that in Al electrode because the As(V) removal substitutes more OH position in Fe-hydroxide than that in Al-hydroxide. EC system with Fe electrode can successfully remove the As(III) but system with Al electrode cannot because As(III) can strongly bind to the surface of Fe-hydroxide with forming inner-sphere species but weakly adsorb to the Al-hydroxide surface with forming outer-sphere species. The acidic solution can destroy the deposited hydroxide passive film then allow the metallic ions liberate into the solution, therefore, the acidic initial solution can enhance the As(V) and As(III) removal. The over potential calculation and potentiodynamic polarization tests reveal that the Fe electrode systems possess higher over potential and pitting potential than that of Al electrode system due to the fast hydrolysis of and the occurrence of Fe-hydroxide passive film.

Cobalt Coordination and Clustering in α-Co(OH)2 Revealed by Synchrotron X-ray Total Scattering

International Nuclear Information System (INIS)

Neilson, James R.; Kurzman, Joshua A.; Seshadri, Ram; Morse, Daniel E.

2010-01-01

Structures of layered metal hydroxides are not well described by traditional crystallography. Total scattering from a synthesis-controlled subset of these materials, as described here, reveals that different cobalt coordination polyhedra cluster within each layer on short length scales, offering new insights and approaches for understanding the properties of these and related layered materials. Structures related to that of brucite (Mg(OH) 2 ) are ubiquitous in the mineral world and offer a variety of useful functions ranging from catalysis and ion-exchange to sequestration and energy transduction, including applications in batteries. However, it has been difficult to resolve the atomic structure of these layered compounds because interlayer disorder disrupts the long-range periodicity necessary for diffraction-based structure determination. For this reason, traditional unit-cell-based descriptions have remained inaccurate. Here we apply, for the first time to such layered hydroxides, synchrotron X-ray total scattering methods - analyzing both the Bragg and diffuse components - to resolve the intralayer structure of three different α-cobalt hydroxides, revealing the nature and distribution of metal site coordination. The different compounds with incorporated chloride ions have been prepared with kinetic control of hydrolysis to yield different ratios of octahedrally and tetrahedrally coordinated cobalt ions within the layers, as confirmed by total scattering. Real-space analyses indicate local clustering of polyhedra within the layers, manifested in the weighted average of different ordered phases with fixed fractions of tetrahedrally coordinated cobalt sites. These results, hidden from an averaged unit-cell description, reveal new structural characteristics that are essential to understanding the origin of fundamental material properties such as color, anion exchange capacity, and magnetic behavior. Our results also provide further insights into the detailed

Cobalt coordination and clustering in alpha-Co(OH)(2) revealed by synchrotron X-ray total scattering.

Science.gov (United States)

Neilson, James R; Kurzman, Joshua A; Seshadri, Ram; Morse, Daniel E

2010-09-03

Structures of layered metal hydroxides are not well described by traditional crystallography. Total scattering from a synthesis-controlled subset of these materials, as described here, reveals that different cobalt coordination polyhedra cluster within each layer on short length scales, offering new insights and approaches for understanding the properties of these and related layered materials. Structures related to that of brucite [Mg(OH)(2)] are ubiquitous in the mineral world and offer a variety of useful functions ranging from catalysis and ion-exchange to sequestration and energy transduction, including applications in batteries. However, it has been difficult to resolve the atomic structure of these layered compounds because interlayer disorder disrupts the long-range periodicity necessary for diffraction-based structure determination. For this reason, traditional unit-cell-based descriptions have remained inaccurate. Here we apply, for the first time to such layered hydroxides, synchrotron X-ray total scattering methods-analyzing both the Bragg and diffuse components-to resolve the intralayer structure of three different alpha-cobalt hydroxides, revealing the nature and distribution of metal site coordination. The different compounds with incorporated chloride ions have been prepared with kinetic control of hydrolysis to yield different ratios of octahedrally and tetrahedrally coordinated cobalt ions within the layers, as confirmed by total scattering. Real-space analyses indicate local clustering of polyhedra within the layers, manifested in the weighted average of different ordered phases with fixed fractions of tetrahedrally coordinated cobalt sites. These results, hidden from an averaged unit-cell description, reveal new structural characteristics that are essential to understanding the origin of fundamental material properties such as color, anion exchange capacity, and magnetic behavior. Our results also provide further insights into the detailed

Identification of new solar OH lines in the 10--12 micron region

International Nuclear Information System (INIS)

Goldman, A.; Murcray, F.J.; Gillis, J.R.; Murcray, D.G.

1981-01-01

High-resolution (0.02 cm -1 ) infrared solar spectra obtained with a balloon-borne interferometer reveal new solar absorption features, which appear as regularly spaced quartets, in the 825--960 cm -1 region. The lines are interpreted as high N'' (25--33) pure rotation lines of solar OH. An effective amount of approx.8 x 10 15 molecules cm -2 of OH is estimated from the spectra

Characterization of the alteration products formed at the surface of LaYSiAlO and CeYSiAlO glasses using ERDA and RBS techniques

International Nuclear Information System (INIS)

Gavarini, S.; Trocellier, P.; Matzen, G.

2004-01-01

Leaching tests have been performed on LnYSiAlO glasses (Ln = La or Ce) that are considered as potential matrices for the specific immobilization of minor actinides. Elastic recoil detection analysis (ERDA) performed on leached samples indicated a superficial hydration of LaYSiAlO glass of about 100-150 nm. This hydrated layer is (Al, Y)-enriched according to SEM-EDS analysis, suggesting the formation of hydroxide (or hydroxycarbonates) compounds including these two elements. This process leads to a very efficient passivation of the material due to the low solubility of Al and Y hydroxides (and hydroxycarbonates) species in near neutral media, even when the solution is rapidly replenished is dynamic leaching experiments. Rutherford Backscattering Spectrometry elemental mapping revealed very localized and significantly Y-enriched deposits at the surface of the sample after leaching. This could be the sign of heterogeneities already present on the pristine glass. These may be correlated with the weak solubility of yttrium (and rare earth) elements in silicate matrices (Y + Ln initial content in the glass ∼11 at.%). In the case of CeYSiAlO glass, a thin layer was formed on the solid after leaching. The simulation of the corresponding RBS spectra showed a surface (Y, Ce)-enrichment and (Al, Si)-depletion in both cases. This could be explained by the oxidation of trivalent cerium initially present in the glass structure during leaching. This might be explained by the low solubility of Ce(IV)-compounds (CeO 2 and/or Ce(OH) 4 ) in solution leading to an enrichment of this element at the glass/solution interface, to form a mixture of amorphous CeO 2 and Y(OH) 3 , as confirmed by XPS and XRD experiments

Novel Montmorillonite/TiO₂/MnAl-Mixed Oxide Composites Prepared from Inverse Microemulsions as Combustion Catalysts.

Science.gov (United States)

Napruszewska, Bogna D; Michalik-Zym, Alicja; Rogowska, Melania; Bielańska, Elżbieta; Rojek, Wojciech; Gaweł, Adam; Wójcik-Bania, Monika; Bahranowski, Krzysztof; Serwicka, Ewa M

2017-11-19

A novel design of combustion catalysts is proposed, in which clay/TiO₂/MnAl-mixed oxide composites are formed by intermixing exfoliated organo-montmorillonite with oxide precursors (hydrotalcite-like in the case of Mn-Al oxide) obtained by an inverse microemulsion method. In order to assess the catalysts' thermal stability, two calcination temperatures were employed: 450 and 600 °C. The composites were characterized with XRF (X-ray fluorescence), XRD (X-ray diffraction), HR SEM (high resolution scanning electron microscopy, N₂ adsorption/desorption at -196 °C, and H₂ TPR (temperature programmed reduction). Profound differences in structural, textural and redox properties of the materials were observed, depending on the presence of the TiO₂ component, the type of neutralization agent used in the titania nanoparticles preparation (NaOH or NH₃ (aq)), and the temperature of calcination. Catalytic tests of toluene combustion revealed that the clay/TiO₂/MnAl-mixed oxide composites prepared with the use of ammonia showed excellent activity, the composites obtained from MnAl hydrotalcite nanoparticles trapped between the organoclay layers were less active, but displayed spectacular thermal stability, while the clay/TiO₂/MnAl-mixed oxide materials obtained with the aid of NaOH were least active. The observed patterns of catalytic activity bear a direct relation to the materials' composition and their structural, textural, and redox properties.

Chemical leaching of rapidly solidified Al-Si binary alloys

International Nuclear Information System (INIS)

Yamauchi, I.; Takahara, K.; Tanaka, T.; Matsubara, K.

2005-01-01

Various particulate precursors of Al 100-x Si x (x = 5-12) alloys were prepared by a rapid solidification process. The rapidly solidified structures of the precursors were examined by XRD, DSC and SEM. Most of Si atoms were dissolved into the α-Al(fcc) phase by rapid solidification though the solubility of Si in the α-Al phase is negligibly small in conventional solidification. In the case of 5 at.% Si alloy, a single α-Al phase was only formed. The amount of the primary Si phase increased with increase of Si content for the alloys beyond 8 at.% Si. Rapid solidification was effective to form super-saturated α-Al precursors. These precursors were chemically leached by using a basic solution (NaOH) or a hydrochloric acid (HCl) solution. All Al atoms were removed by a HCl solution as well as a NaOH solution. Granules of the Si phase were newly formed during leaching. The specific surface area was about 50-70 m 2 /g independent of Si content. The leaching behavior in both solutions was slightly different. In the case of a NaOH solution, the shape of the precursor often degenerated after leaching. On the other hand, it was retained after leaching by a HCl solution. Fine Si particles precipitated in the α-Al phase by annealing of as-rapidly solidified precursors at 773 K for 7.2 x 10 3 s. In this case, it was difficult to obtain any products by NaOH leaching, but a few of Si particles were obtained by HCl leaching. Precipitated Si particles were dissolved by the NaOH solution. The X-ray diffraction patterns of leached specimens showed broad lines of the Si phase and its lattice constant was slightly larger than that of the pure Si phase. The microstructures of the leached specimens were examined by transmission electron microscopy. It showed that the leached specimens had a skeletal structure composed of slightly elongated particles of the Si phase and quite fine pores. The particle size was about 30-50 nm. It was of comparable order with that evaluated by Scherer

Sources and physical processes responsible for OH/H2O in the lunarsoil as revealed by the Moon Mineralogy Mapper (M3)

Science.gov (United States)

McCord, T.B.; Taylor, L.A.; Combe, J.-P.; Kramer, G.; C.M. Pieters,; Sunshine, J.M.; Clark, R.N.

2011-01-01

Analysis of two absorption features near 3 μm in the lunar reflectance spectrum, observed by the orbiting M3 spectrometer and interpreted as being due to OH and H2O, is presented, and the results are used to discuss the processes producing these molecules. This analysis focuses on the dependence of the absorptions on lunar physical properties, including composition, illumination, latitude, and temperature. Solar wind proton-induced hydroxylation is proposed as the creation process, and its products could be a source for other reported types of hydrogen-rich material and water. The irregular and damaged fine-grained lunar soil seems especially adapted for trapping solar wind protons and forming OH owing to abundant dangling oxygen bonds. The M3data reveal that the strengths of the two absorptions are correlated and widespread, and both are correlated with lunar composition but in different ways. Feldspathic material seems richer in OH. These results seem to rule out water from the lunar interior and cometary infall as major sources. There appear to be correlations of apparent band strengths with time of day and lighting conditions. However, thermal emission from the Moon reduces the apparent strengths of the M3absorptions, and its removal is not yet completely successful. Further, many of the lunar physical properties are themselves intercorrelated, and so separating these dependencies on the absorptions is difficult, due to the incomplete M3 data set. This process should also operate on other airless silicate surfaces, such as Mercury and Vesta, which will be visited by the Dawn spacecraft in mid-2011.

Adsorption of cadmium onto Al{sub 13}-pillared acid-activated montmorillonite

Energy Technology Data Exchange (ETDEWEB)

Yan Liangguo [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, P.O. Box 2871, Beijing 100085 (China); Shan Xiaoquan [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, P.O. Box 2871, Beijing 100085 (China)], E-mail: xiaoquan@rcees.ac.cn; Wen Bei [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, P.O. Box 2871, Beijing 100085 (China); Owens, Gary [Centre for Environmental Risk Assessment and Remediation, University of South Australia, Mawson Lakes Campus, Mawson Lakes, Boulevard, South Australia 5095 (Australia)

2008-08-15

The optimal preparation conditions for Al{sub 13}-pillared acid-activated Na{sup +}-montmorillonite (Al{sub 13}-PAAMt) were (1) an acid-activated Na{sup +}-montmorillonite (Na{sup +}-Mt) solution of pH 3.0, (2) a OH{sup -}/Al{sup 3+} molar ratio of 2.4 and (3) Al{sup 3+}/Na{sup +}-Mt ratio of 1.0 mmol g{sup -1}. The effects of OH{sup -}/Al{sup 3+} and Al{sup 3+}/Na{sup +}-Mt ratios on the adsorption of Cd{sup 2+} onto Al{sub 13}-PAAMt were studied. A comparison of the adsorption of Cd{sup 2+} onto Al{sub 13}-PAAMt, Al{sub 13}-pillared Na{sup +}-montmorillonite (Al{sub 13}-PMt) and Na{sup +}-Mt suggested that Al{sub 13}-PAAMt had higher adsorption affinity for Cd{sup 2+} than the other two adsorbents. A pseudo-second-order model described the adsorption kinetics well. Cadmium adsorption followed the Langmuir two-site equation, while desorption was hysteretic.

Cognitive-behavioral screening reveals prevalent impairment in a large multicenter ALS cohort.

Science.gov (United States)

Murphy, Jennifer; Factor-Litvak, Pam; Goetz, Raymond; Lomen-Hoerth, Catherine; Nagy, Peter L; Hupf, Jonathan; Singleton, Jessica; Woolley, Susan; Andrews, Howard; Heitzman, Daragh; Bedlack, Richard S; Katz, Jonathan S; Barohn, Richard J; Sorenson, Eric J; Oskarsson, Björn; Fernandes Filho, J Americo M; Kasarskis, Edward J; Mozaffar, Tahseen; Rollins, Yvonne D; Nations, Sharon P; Swenson, Andrea J; Koczon-Jaremko, Boguslawa A; Mitsumoto, Hiroshi

2016-03-01

To characterize the prevalence of cognitive and behavioral symptoms using a cognitive/behavioral screening battery in a large prospective multicenter study of amyotrophic lateral sclerosis (ALS). Two hundred seventy-four patients with ALS completed 2 validated cognitive screening tests and 2 validated behavioral interviews with accompanying caregivers. We examined the associations between cognitive and behavioral performance, demographic and clinical data, and C9orf72 mutation data. Based on the ALS Cognitive Behavioral Screen cognitive score, 6.5% of the sample scored below the cutoff score for frontotemporal lobar dementia, 54.2% scored in a range consistent with ALS with mild cognitive impairment, and 39.2% scored in the normal range. The ALS Cognitive Behavioral Screen behavioral subscale identified 16.5% of the sample scoring below the dementia cutoff score, with an additional 14.1% scoring in the ALS behavioral impairment range, and 69.4% scoring in the normal range. This investigation revealed high levels of cognitive and behavioral impairment in patients with ALS within 18 months of symptom onset, comparable to prior investigations. This investigation illustrates the successful use and scientific value of adding a cognitive-behavioral screening tool in studies of motor neuron diseases, to provide neurologists with an efficient method to measure these common deficits and to understand how they relate to key clinical variables, when extensive neuropsychological examinations are unavailable. These tools, developed specifically for patients with motor impairment, may be particularly useful in patient populations with multiple sclerosis and Parkinson disease, who are known to have comorbid cognitive decline. © 2016 American Academy of Neurology.

Photodissociation thresholds of OH produced from CH sub 3 OH in solid neon and argon

CERN Document Server

Cheng, B M; Lo, W J; Lee, Y P

2001-01-01

Photodissociation thresholds of OH from CH sub 3 OH in solid Ne and Ar were determined via photolysis of CH sub 3 OH/Ne and CH sub 3 OH/Ar (1/200) samples in situ at 4 K. The samples were irradiated with VUV synchrotron radiation after dispersion by a Seya-Namioka monochromator. The OH photo-product was detected by means of laser-induced fluorescence technique. The increase of fluorescent intensity of OH was monitored and recorded after the matrix sample was irradiated at different wavelengths for 3-5 min. Photodissociation threshold energies of 7.13+-0.02 eV (174.0+-0.5 nm) and 7.08+-0.04 eV (175.0+-1.0 nm) were measured for OH production of CH sub 3 OH in solid Ne and Ar, respectively.

Enhanced fluoride adsorption using Al (III) modified calcium hydroxyapatite

International Nuclear Information System (INIS)

Nie, Yulun; Hu, Chun; Kong, Chuipeng

2012-01-01

Highlights: ► Al modified hydroxyapatite possessed a higher defluoridation capacity of 32.57 mg/g. ► Hydroxyl groups on the surface of Al-HAP was the adsorption sites for F − removal. ► Enhanced F − removal over Al-HAP was attributed to the modification with aluminum. - Abstract: Aluminum-modified hydroxyapatite (Al-HAP) was prepared and characterized using XRD and BET analyses. Al-HAP possessed higher defluoridation capacity (DC) of 32.57 mgF − /g than unmodified hydroxyapatite (HAP) which showed a DC of 16.38 mgF − /g. The effect of Al/Ca atomic ratio in Al-HAP, solution pH and co-existing anions was further studied. The results indicated that the adsorption data could be well described by the Langmuir isotherm model and the adsorption kinetic followed the pseudo-second-order model. The pH changes during the adsorption process suggested that the -OH on the surface of Al-HAP was the adsorption sites. The more adsorption sites were formed on Al modified HAP, which possessed abundant surface hydroxyl groups, resulting in higher efficiency of F − removal. Thermodynamic parameters such as ΔG°, ΔH° and ΔS° were calculated in order to understand the nature of adsorption process. The results revealed that the adsorption reaction was a spontaneous and endothermic process.

Ternary Ni–Cu–OH and Ni–Co–OH electrodes for electrochemical energy storage

KAUST Repository

Alhebshi, Nuha; Alshareef, Husam N.

2015-01-01

In this project, Ni–Cu–OH and Ni–Co–OH ternary electrodes have been prepared. Different Ni:Cu and Ni:Co ratios were deposited by chemical bath deposition (CBD) at room temperature on carbon microfibers. Since Ni(OH)2 is notorious for poor cycling

The Influence of Backwater Al3+ on Diaspore Bauxite Flotation

Directory of Open Access Journals (Sweden)

Chaojun Fang

2017-10-01

Full Text Available The effect of Al3+ in backwater on the flotation of diaspore bauxite was investigated by micro-flotation tests and the underlying mechanisms were investigated by inductively coupled plasma (ICP measurement, zeta potential measurements, solution chemistry analyses, and synchrotron near edge X-ray absorption fine structure (NEXAFS analyses. The ICP measurement results show the concentration of Al3+ in backwater was up to 1 × 10−4 mol/L. The micro-flotation results indicated that backwater Al3+ reduced the flotation recovery of diaspore and improved the flotation recovery of kaolinite at pH 9, which was the pH value used in the industrial flotation. The adsorption of Al3+ species changed the zeta potential, the Al atomic abundance, and the number of active sites on the mineral surface. In particular, the result of solution chemistry analyses and synchrotron NEXAFS analyses show that the Al3+ in backwater was adsorbed on the mineral surface in the form of Al(OH3 (s, and the bond of –Al–O–Al–(OH2 or –Al/Si–O–Al–(OH2 was formed at pH 9. It changed the intensity of hydrogen bond force between minerals and collectors, and resulted in the depression of diaspore flotation and the activation of kaolinite flotation. This study can be used to guide the application of backwater in the flotation of diaspore bauxite in industry.

Ionothermal synthesis, crystal structure, and magnetic study of Co2PO4OH isostructural with caminite.

Science.gov (United States)

Wang, Guangmei; Valldor, Martin; Spielberg, Eike T; Mudring, Anja-Verena

2014-03-17

A new framework cobalt(II) hydroxyl phosphate, Co2PO4OH, was prepared by ionothermal synthesis using 1-butyl-4-methyl-pyridinium hexafluorophosphate as the ionic liquid. As the formation of Co2PO4F competes in the synthesis, the synthesis conditions have to be judiciously chosen to obtain well-crystallized, single phase Co2PO4OH. Single-crystal X-ray diffraction analyses reveal Co2PO4OH crystallizes with space group I41/amd (a = b = 5.2713(7) Å, c = 12.907(3) Å, V = 358.63(10) Å(3), and Z = 4). Astonishingly, it does not crystallize isotypically with Co2PO4F but rather isotypically with the hydroxyl minerals caminite Mg1.33[SO4(OH)0.66(H2O)0.33] and lipscombite Fe(2–y)PO4(OH) (0 ≤ y ≤ 2/3). Phosphate tetrahedra groups interconnect four rod-packed face-sharing ∞(1){CoO(6/2)} octahedra chains to form a three-dimensional framework structure. The compound Co2PO4OH was further characterized by powder X-ray diffraction, Fourier transform–infrared, and ultraviolet–visible spectroscopy, confirming the discussed structure. The magnetic measurement reveals that Co2PO4OH undergoes a magnetic transition and presents at low temperatures a canted antiferromagnetic spin order in the ground state.

The removal of bisphenol A from aqueous solutions by MIL-53(Al) and mesostructured MIL-53(Al).

Science.gov (United States)

Zhou, Meimei; Wu, Yi-Nan; Qiao, Junlian; Zhang, Jing; McDonald, Amanda; Li, Guangtao; Li, Fengting

2013-09-01

In this work, metal-organic framework MIL-53(Al){Al(OH)[O2C-C6H4-CO2]} and MIL-53(Al)-F127{Al(OH)[O2C-C6H4-CO2]} were synthesized and used as sorbents to remove bisphenol A (BPA) from aqueous system. The sorption kinetics data of BPA were found to be in agreement with the pseudo-second-order model. The equilibrium sorption amounts of BPA on MIL-53(Al) and MIL-53(Al)-F127 reached 329.2±16.5 and 472.7±23.6 mg g(-1), respectively, far more than that of commercial activated carbons (ranging from 129.6 to 263.1 mg g(-1)). Both MIL-53(Al) and MIL-53(Al)-F127 could remove BPA fast from aqueous solutions, and the required contact time to reach equilibrium was approximately 90 min for MIL-53(Al) and 30 min for MIL-53(Al)-F127, respectively. The optimum pH levels for the removal of BPA using MIL-53 (Al) and MIL-53(Al)-F127 were 4 and 6 separately. The optimum temperature for the sorption behavior of BPA on the two sorbents was 20 °C. The results performed show that the resulting products, as one kind of MOFs, can be regarded as a new class of sorbents for water treatment and could find great applications in the fields of environmental water pollution control and resources reuse. Copyright © 2013 Elsevier Inc. All rights reserved.

Tomographic reconstruction of OH* chemiluminescence in two interacting turbulent flames

International Nuclear Information System (INIS)

Worth, Nicholas A; Dawson, James R

2013-01-01

The tomographic reconstruction of OH* chemiluminescence was performed on two interacting turbulent premixed bluff-body stabilized flames under steady flow conditions and acoustic excitation. These measurements elucidate the complex three-dimensional (3D) vortex–flame interactions which have previously not been accessible. The experiment was performed using a single camera and intensifier, with multiple views acquired by repositioning the camera, permitting calculation of the mean and phase-averaged volumetric OH* distributions. The reconstructed flame structure and phase-averaged dynamics are compared with OH planar laser-induced fluorescence and flame surface density measurements for the first time. The volumetric data revealed that the large-scale vortex–flame structures formed along the shear layers of each flame collide when the two flames meet, resulting in complex 3D flame structures in between the two flames. With a fairly simple experimental setup, it is shown that the tomographic reconstruction of OH* chemiluminescence in forced flames is a powerful tool that can yield important physical insights into large-scale 3D flame dynamics that are important in combustion instability. (paper)

Electrochemical deposition of Mg(OH2/GO composite films for corrosion protection of magnesium alloys

Directory of Open Access Journals (Sweden)

Fengxia Wu

2015-09-01

Full Text Available Mg(OH2/graphene oxide (GO composite film was electrochemical deposited on AZ91D magnesium alloys at constant potential. The characteristics of the Mg(OH2/GO composite film were investigated by scanning electron microscope (SEM, energy-dispersive X-ray spectrometry (EDS, X-ray diffractometer (XRD and Raman spectroscopy. It was shown that the flaky GO randomly distributed in the composite film. Compared with the Mg(OH2 film, the Mg(OH2/GO composite film exhibited more uniform and compact structure. Potentiodynamic polarization tests revealed that the Mg(OH2/GO composite film could significantly improve the corrosion resistance of Mg(OH2 film with an obvious positive shift of corrosion potential by 0.19 V and a dramatic reduction of corrosion current density by more than one order of magnitude.

Biodistribution and tumor uptake of C60(OH)x in mice

International Nuclear Information System (INIS)

Ji Zhiqiang; Sun Hongfang; Wang Haifang; Xie Qunying; Liu Yuangfang; Wang Zheng

2006-01-01

Radiolabeling of fullerol, 125 I-C 60 (OH) x , was performed by the traditional chloramine-T method. The C-I covalent bond in I-C 60 (OH) x was characterized by X-ray photoelectron spectroscopy (XPS) that was sufficiently stable for in vivo study. Laser light scattering spectroscopy clearly showed that C 60 (OH) x aggregated to large nanoparticle clumps with a wide range of distribution. The clumps formed were also visualized by transmission electron microscope (TEM). We examined the biodistribution and tumor uptake of C 60 (OH) x in five mouse bearing tumor models, including mouse H22 hepatocarcinoma, human lung giantcellcarcinoma PD, human colon cancer HCT-8, human gastric cancer MGC803, and human OS732 osteosarcoma. The accumulation ratios of 125 I-C 60 (OH) x in mouse H22 hepatocarcinoma to that in normal muscle tissue (T/N) and blood (T/B) at 1, 6, 24 and 72 h, reveal that 125 I-C 60 (OH) x gradually accumulates in H22 tumor, and retains for a quite long period (e.g., T/N 3.41, T/B 3.94 at 24 h). For the other four tumor models, the T/N ratio at 24 h ranges within 1.21-6.26, while the T/B ratio ranges between 1.23 and 4.73. The accumulation of C 60 (OH) x in tumor is mostly due to the enhanced permeability and retention effect (EPR) and the phagocytosis of mononuclear phagocytes. Hence, C 60 (OH) x might serve as a photosensitizer in the photodynamic therapy of some kinds of tumor

The far-infrared spectrum of the OH radical

Science.gov (United States)

Brown, J. M.; Schubert, J. E.; Evenson, K. M.; Radford, H. E.

1982-01-01

It is thought likely that the study of spectral lines in the far-infrared might provide at least as much information about the physics and chemistry of the interstellar environment as radioastronomy. However, by comparison with the microwave region, the far-infrared is largely unexplored. There is a pressing need for good laboratory data to aid searches and assignments of spectra from the interstellar clouds and nebulae. Brown et al. (1981) have conducted a study of the laser magnetic resonance (LMR) spectrum of the OH radical in its ground state at far-infrared wavelengths. The present investigation is concerned with the computation of the frequencies of individual hyperfine transitions involving all rotational levels up to J = 4 1/2. The results of the calculation are presented in a table. The results are summarized in a diagram which shows the low-lying energy levels of OH. The frequencies of transitions between levels studied directly in the LMR spectrum are quite reliable.

Structural diversity of a family of aluminophosphates with Al/P ratio of non-unity

Science.gov (United States)

Yu, Jihong; Xu, Ruren; Li, Jiyang

2000-05-01

A family of organically templated aluminophosphates (denoted AlPOs) with an Al/P ratio of non-unity has been prepared with 1-D chain, 2-D layer and 3-D open-framework architectures. Their inorganic parts are constructed from alternating Al-centered polyhedra (AlO 4, AlO 5, AlO 4(OH 2) 2) and P-centered tetrahedra P(OAl) nO 4- n ( n=0, 1, 2, 3). The existence of terminal POH and/or PO groups in the structures results in the deviation of Al/P ratio from unity, and the commonly encountered Al/P ratios are 1/2, 3/5, 2/3, 3/4, 4/5 and 5/6. This review will discuss the structural features of these AlPOs with various dimensionalities and stoichiometries.

FT-Raman and FT-IR spectroscopy of synthetic Mg/Zn/Al-hydrotalcites

International Nuclear Information System (INIS)

Leishman, N.; Kloprogge, J.T.; Fry, R.; Frost, R.L.

1998-01-01

Full text: Hydrotalcites, also known as layered double hydroxides, are less well known and more diffuse in nature than cationic clays. They can be visualised as positively charged hydroxide layers comparable to brucite in which a part of the Mg 2+ is substituted by a trivalent metal like Al 3+ or Fe 3+ separated by charge compensating mostly hydrated interlayer anions. In synthetic hydrotalcites a broad range of compositions are possible of the type [M 2+ 1-x M 3+ x (OH) 2 ][A n- ] x/n -yH 2 O, where M 2+ and M 3+ are the di- and trivalent cations in the octahedral positions within the hydroxide layers with x between 0.17 and 0.33. A n- is an exchangeable interlayer anion. The hydrotalcites with Mg/Zn/Al atomic ratios of 6/0/2, 4/2/2, 2/4/2 and 0/6/2 were synthesised by the slow simultaneous addition of a mixed aluminum-magnesium-zinc nitrate solution and a NaOH solution under vigorous stirring buffering the pH at ± 10. The products were washed to eliminate excess salt and dried at 60 deg C. The nature of the resulting material was checked by XRD and TEM. Both proved the materials to exist of only crystalline hydrotalcite except for the Zn 6 Al 2 (OH) 16 CO 3 .nH 2 O, which contained some unidentified products. The infrared and Raman spectra of synthetic hydrotalcites with different Mg/Zn ratios reveal complicated spectra. Based on the differences in the spectra between the various hydrotalcites and comparison to the comparable hydroxides and hydroxycarbonates a much more detailed band assignment can be made than has been published before

Sources and physical processes responsible for OH/H2O in the lunar soil as revealed by the Moon Mineralogy Mapper (M3)

Science.gov (United States)

McCord, T.B.; Taylor, L.A.; Combe, J.-P.; Kramer, G.; Pieters, C.M.; Sunshine, J.M.; Clark, R.N.

2011-01-01

Analysis of two absorption features near 3 m in the lunar reflectance spectrum, observed by the orbiting M3 spectrometer and interpreted as being due to OH and H2O, is presented, and the results are used to discuss the processes producing these molecules. This analysis focuses on the dependence of the absorptions on lunar physical properties, including composition, illumination, latitude, and temperature. Solar wind proton-induced hydroxylation is proposed as the creation process, and its products could be a source for other reported types of hydrogen-rich material and water. The irregular and damaged fine-grained lunar soil seems especially adapted for trapping solar wind protons and forming OH owing to abundant dangling oxygen bonds. The M3 data reveal that the strengths of the two absorptions are correlated and widespread, and both are correlated with lunar composition but in different ways. Feldspathic material seems richer in OH. These results seem to rule out water from the lunar interior and cometary infall as major sources. There appear to be correlations of apparent band strengths with time of day and lighting conditions. However, thermal emission from the Moon reduces the apparent strengths of the M3 absorptions, and its removal is not yet completely successful. Further, many of the lunar physical properties are themselves intercorrelated, and so separating these dependencies on the absorptions is difficult, due to the incomplete M3 data set. This process should also operate on other airless silicate surfaces, such as Mercury and Vesta, which will be visited by the Dawn spacecraft in mid-2011. Copyright 2011 by the American Geophysical Union.

Novel Semi-Direct OH Reactivity (kOH) Measurements by Chemical Ionization Mass Spectrometry during a Chamber Instrument Comparison Campaign and Continuous Ambient Air Sampling at a Central European GAW Station

Science.gov (United States)

Muller, J.; Kubistin, D.; Elste, T.; Plass-Duelmer, C.; Claude, A.; Englert, J.; Holla, R.; Fuchs, H.; Hofzumahaus, A.; Holland, F.; Novelli, A.; Tillmann, R.; Wegener, R.; Rohrer, F.; Yu, Z.; Bohn, B.; Williams, J.; Pfannerstill, E.; Edtbauer, A.; Kluepfel, T.

2016-12-01

Total OH reactivity (kOH) has been recognized as a useful measure to gauge the potential atmospheric oxidation capacity and a few different in-situ measurement techniques have been developed over the last 15 years. Here results are presented from a novel semi-direct method developed by the German Weather Service (DWD) utilizing a chemical ionization mass spectrometer (CIMS). Recently in April 2016, the CIMS system participated in a half-blind kOH instrument comparison campaign at the Forschungszentrum Jülich (FZJ) SAPHIR chamber. Experiments provided controlled conditions with a range of different VOC mixtures and varying NOx levels, representing environments dominated by biogenic or urban emissions. Alongside CIMS, kOH was also measured by systems using the comparative reactivity method (CRM) and the pump-probe technique with OH detection. The intercomparison revealed a good performance of CIMS at lower OH reactivities (0-15 s-1), a range for which the instrumental set up was optimized. Limitations of the CIMS system consist of an upper limit for kOH detection and the need for applying a chemical correction function as a result of instrument-internal HOx recycling. Findings and instrument parameters obtained from the FZJ SAPHIR campaign and flow tube experiments are then applied to ambient air kOH measurements at the Meteorological Observatory Hohenpeissenberg (MOHp), Germany. The CIMS instrument is used there for long-term measurements of OH, H2SO4, ROx and kOH. Here, we show ambient air kOH measurements, interpreted in conjunction with volatile organic compounds (VOC) and inorganic trace gases also measured at the GAW station Hohenpeissenberg. These observations provide a unique dataset to investigate turnover rates and seasonal cycles of reactive trace gases, i.e. sources that make up total OH reactivity in this central European, rural setting.

Lamellar-crossing-structured Ni(OH){sub 2}/CNTs/Ni(OH){sub 2} nanocomposite for electrochemical supercapacitor materials

Energy Technology Data Exchange (ETDEWEB)

Wu, Qingnan [Department of Chemistry, State Key Laboratory of Pollution Control and Resource Reuse, Tongji University, Shanghai 200092 (China); Wen, Ming, E-mail: m_wen@tongji.edu.cn [Department of Chemistry, State Key Laboratory of Pollution Control and Resource Reuse, Tongji University, Shanghai 200092 (China); Shanghai Key Lab of Chemical Assessment and Sustainability, Tongji University, Shanghai 200092 (China); Chen, Shipei [Department of Chemistry, State Key Laboratory of Pollution Control and Resource Reuse, Tongji University, Shanghai 200092 (China); Wu, Qingsheng [Department of Chemistry, State Key Laboratory of Pollution Control and Resource Reuse, Tongji University, Shanghai 200092 (China); Shanghai Key Lab of Chemical Assessment and Sustainability, Tongji University, Shanghai 200092 (China)

2015-10-15

Ni(OH){sub 2}/CNTs/Ni(OH){sub 2} lamellar-crossing-nanostructure with a single lamellar spacing of ∼5 nm was effectively constructed through two-phase-interface reaction process followed by the CNTs crossed among the lamellar-nanostructured Ni(OH){sub 2}. The resultant nanocomposite can offer large active surface areas and short diffusion paths for electrons and ions, and is investigated as a potential pseudocapacitor electrode material for electrochemical energy storage applications. Electrochemical data demonstrate that the as-prepared nanocomposite exhibits a high specific capacitance of ∼1600 F g{sup −1} at the scan rate of 1 mV s{sup −1} in 6 M KOH solution at normal pressure and temperature, which is great higher than Ni(OH){sub 2} (∼1200 F g{sup −1}). Furthermore, Ni(OH){sub 2}/CNTs/Ni(OH){sub 2} nanocomposite shows a higher energy density (∼125 Wh kg{sup −1}, 2 A g{sup −1}) and has a slightly decrease of 5% in specific capacitance after 1000 continuous charge/discharge cycles. - Graphical abstract: As-constructed Ni(OH){sub 2}/CNTs/Ni(OH){sub 2} lamellar-crossing-nanostructure exhibits remarkable enhancement in electrochemical stability and high specific capacity of ∼1600 F g{sup −1} at a scan rate of 1 mV s{sup −1}, suggesting promising potential for supercapacitor applications. - Highlights: • New designed lamellar-crossing-structured Ni(OH){sub 2}/CNTs/Ni(OH){sub 2} nanocomposites have been firstly reported in this work. • Ni(OH){sub 2}/CNTs/Ni(OH){sub 2} lamellar-crossing-nanostructures show firm nanostructure and excellent electrochemical stability. • Ni(OH){sub 2}/CNTs/Ni(OH){sub 2} nanocomposites exhibit excellent specific capacitance. • Ni(OH){sub 2}/CNTs/Ni(OH){sub 2} nanocomposites have the potential application in electrochemical energy storage applications.

Breakdown of middle lamella pectin by (●) OH during rapid abscission in Azolla.

Science.gov (United States)

Yamada, Yoshiya; Koibuchi, Mizuki; Miyamoto, Kensuke; Ueda, Junichi; Uheda, Eiji

2015-08-01

Azolla, a small water fern, abscises its roots and branches within 30 min upon treatment with various stresses. This study was conducted to test whether, in the rapid abscission that occurs in Azolla, breakdown of wall components of abscission zone cells by (●) OH is involved. Experimentally generated (●) OH caused the rapid separation of abscission zone cells from detached roots and the rapid shedding of roots from whole plants. Electron microscopic observations revealed that (●) OH rapidly and selectively dissolved a well-developed middle lamella between abscission zone cells and resultantly caused rapid cell separation and shedding. Treatment of abscission zones of Impatiens leaf petiole with (●) OH also accelerated the separation of abscission zone cells. However, compared with that of Azolla roots, accelerative effects in Impatiens were weak. A large amount of (●) OH was cytochemically detected in abscission zone cells both of Azolla roots and of Impatiens leaf petioles. These results suggest that (●) OH is involved in the cell separation process not only in the rapid abscission in Azolla but also in the abscission of Impatiens. However, for rapid abscission to occur, a well-developed middle lamella, a unique structure, which is sensitive to the attack of (●) OH, might be needed. © 2015 John Wiley & Sons Ltd.

Ternary Ni–Cu–OH and Ni–Co–OH electrodes for electrochemical energy storage

KAUST Repository

Alhebshi, Nuha

2015-10-01

In this project, Ni–Cu–OH and Ni–Co–OH ternary electrodes have been prepared. Different Ni:Cu and Ni:Co ratios were deposited by chemical bath deposition (CBD) at room temperature on carbon microfibers. Since Ni(OH)2 is notorious for poor cycling stability, the goal of the work was to determine if doping with Cu or Co could improve Ni(OH)2 cycling stability performance and conductivity against reaction with electrolyte. It is observed that the electrodes with Ni:Cu and Ni:Co composition ratio of 100:10 result in the optimum capacitance and cycling stability in both Ni–Cu–OH and Ni–Co–OH electrodes. This improvement in cycling stability can be attributed to the higher redox reversibility as indicated by the smaller CV redox peak separation. In addition, it is found that decreasing Cu and Co ratios, with fixed CBD time, enhances nanoflakes formation, and hence increases electrode capacitance. For the optimum composition (Ni:Co = 100:10), composites of the ternary electrodes with graphene and carbon nanofibers were also tested, with resultant improvement in potential window, equivalent series resistance, areal capacitance and cycling stability.

Growth and characterization of Al{sub 2}O{sub 3} films on fluorine functionalized epitaxial graphene

Energy Technology Data Exchange (ETDEWEB)

Robinson, Zachary R., E-mail: ZRobinso@Brockport.edu [Department of Physics, The College at Brockport, Brockport, New York 14420 (United States); Jernigan, Glenn G.; Wheeler, Virginia D.; Hernández, Sandra C.; Eddy, Charles R. [U.S. Naval Research Laboratory, Washington, DC 20375 (United States); Mowll, Tyler R.; Ong, Eng Wen [College of Nanoscale Science and Engineering, University at Albany-SUNY, Albany, New York 12203 (United States); Ventrice, Carl A. [College of Nanoscale Science, SUNY Polytechnic Institute, Albany, New York 12203 (United States); Geisler, Heike [Department of Chemistry and Biochemistry, SUNY Oneonta, Oneonta, New York 13820 (United States); Pletikosic, Ivo; Yang, Hongbo; Valla, Tonica [Brookhaven National Laboratory, Brookhaven, New York 11973 (United States)

2016-08-21

Intelligent engineering of graphene-based electronic devices on SiC(0001) requires a better understanding of processes used to deposit gate-dielectric materials on graphene. Recently, Al{sub 2}O{sub 3} dielectrics have been shown to form conformal, pinhole-free thin films by functionalizing the top surface of the graphene with fluorine prior to atomic layer deposition (ALD) of the Al{sub 2}O{sub 3} using a trimethylaluminum (TMA) precursor. In this work, the functionalization and ALD-precursor adsorption processes have been studied with angle-resolved photoelectron spectroscopy, low energy electron diffraction, and X-ray photoelectron spectroscopy. It has been found that the functionalization process has a negligible effect on the electronic structure of the graphene, and that it results in a twofold increase in the adsorption of the ALD-precursor. In situ TMA-dosing and XPS studies were also performed on three different Si(100) substrates that were terminated with H, OH, or dangling Si-bonds. This dosing experiment revealed that OH is required for TMA adsorption. Based on those data along with supportive in situ measurements that showed F-functionalization increases the amount of oxygen (in the form of adsorbed H{sub 2}O) on the surface of the graphene, a model for TMA-adsorption on graphene is proposed that is based on a reaction of a TMA molecule with OH.

The OH-initiated oxidation of atmospheric peroxyacetic acid: Experimental and model studies

Science.gov (United States)

Wu, Huihui; Wang, Yin; Li, Huan; Huang, Liubin; Huang, Dao; Shen, Hengqing; Xing, Yanan; Chen, Zhongming

2017-09-01

Peroxyacetic acid (PAA, CH3C(O)OOH) plays an important role in atmospheric chemistry, serving as reactive oxidant and affecting radical recycling. However, previous studies revealed an obvious gap between modelled and observed concentrations of atmospheric PAA, which may be partly ascribed to the uncertainty in the kinetics and mechanism of OH-oxidation. In this study, we measured the rate constant of OH radical reaction with PAA (kPAA+OH) and investigated the products in order to develop a more robust atmospheric PAA chemistry. Using the relative rates technique and employing toluene and meta-xylene as reference compounds, the kPAA+OH was determined to be (9.4-11.9) × 10-12 cm3 molecule-1 s-1 at 298 K and 1 atm, which is about (2.5-3.2) times larger than that parameter used in Master Chemical Mechanism v3.3.1 (MCM v3.3.1) (3.70 × 10-12 cm3 molecule-1 s-1). Incorporation of a box model and MCM v3.3.1 with revised PAA chemistry represented a better simulation of atmospheric PAA observed during Wangdu Campaign 2014, a rural site in North China Plain. It is found that OH-oxidation is an important sink of atmospheric PAA in this rural area, accounting for ∼30% of the total loss. Moreover, the major terminal products of PAA-OH reaction were identified as formaldehyde (HCHO) and formic acid (HC(O)OH). The modelled results show that both primary and secondary chemistry play an important role in the large HCHO and HC(O)OH formation under experimental conditions. There should exist the channel of methyl H-abstraction for PAA-OH reaction, which may also provide routes to HCHO and HC(O)OH formation.

Esuuman et al (17)

African Journals Online (AJOL)

big timmy

ether (Sathe et al., 2002). Various extraction conditions such as pH, solvent types (NaOH, NaCl or Ethanol), solvent concentration, extraction time, solvent/flour ratio, may affect the final properties of the extracted protein. When many factors and interactions affect desired responses in a certain process design, Response.

Novel Montmorillonite/TiO2/MnAl-Mixed Oxide Composites Prepared from Inverse Microemulsions as Combustion Catalysts

Directory of Open Access Journals (Sweden)

Bogna D. Napruszewska

2017-11-01

Full Text Available A novel design of combustion catalysts is proposed, in which clay/TiO2/MnAl-mixed oxide composites are formed by intermixing exfoliated organo-montmorillonite with oxide precursors (hydrotalcite-like in the case of Mn-Al oxide obtained by an inverse microemulsion method. In order to assess the catalysts’ thermal stability, two calcination temperatures were employed: 450 and 600 °C. The composites were characterized with XRF (X-ray fluorescence, XRD (X-ray diffraction, HR SEM (high resolution scanning electron microscopy, N2 adsorption/desorption at −196 °C, and H2 TPR (temperature programmed reduction. Profound differences in structural, textural and redox properties of the materials were observed, depending on the presence of the TiO2 component, the type of neutralization agent used in the titania nanoparticles preparation (NaOH or NH3 (aq, and the temperature of calcination. Catalytic tests of toluene combustion revealed that the clay/TiO2/MnAl-mixed oxide composites prepared with the use of ammonia showed excellent activity, the composites obtained from MnAl hydrotalcite nanoparticles trapped between the organoclay layers were less active, but displayed spectacular thermal stability, while the clay/TiO2/MnAl-mixed oxide materials obtained with the aid of NaOH were least active. The observed patterns of catalytic activity bear a direct relation to the materials’ composition and their structural, textural, and redox properties.

13C, 18O, and D Fractionation Effects in the Reactions of CH3OH Isotopologues with Cl andOH Radicals

DEFF Research Database (Denmark)

Feilberg, Karen; Gruber-Stadler, Margaret; Johnson, Matthew Stanley

2008-01-01

A relative rate experiment is carried out for six isotopologues of methanol and their reactions with OH and Cl radicals. The reaction rates of CH2DOH, CHD2OH, CD3OH, 13CH3OH, and CH3 18OH with Cl and OH radicals are measured by long-path FTIR spectroscopy relative to CH3OH at 298 ( 2 K and 1013...... with measured high-resolution infrared spectra as references. The relative reaction rates defined as R ) klight/kheavy are determined to be: kOH + CH3OH/kOH + 13CH3OH ) 1.031 ( 0.020, kOH + CH3OH/kOH + CH3 18OH ) 1.017 ( 0.012, kOH + CH3OH/kOH + CH2DOH ) 1.119 ( 0.045, kOH + CH3OH/kOH + CHD2OH ) 1.326 ( 0...... reactions with CH3OH were further investigated using canonical variational transition state theory with small curvature tunneling and compared to experimental measurements as well as to those observed in CH4 and several other substituted methane species. Udgivelsesdato: 16 August 2008...

The purification of coal tar by the addition of quinoline and Zn(oh)/sub 2/

International Nuclear Information System (INIS)

Zhou, P.; Chen, Q.L.; Ao, X.Q.; Kang, C

2017-01-01

The coal tar was purified by the addition of quinoline and Zn(OH)2, in order to decrease the content of carbon and inorganic oxide particles. The effect on the viscosity and ash content of the coal tar were investigated by altering temperature, time, and the amount of quinolone and Zn(OH)2 . When the volume ratio between quinolone and coal tar was 20:1 and the static time was 24 h. The viscosity of three layers decreased with rising temperature. When the static temperature and time was 45 °C and 24 h, respectively. The viscosity of three layers decreased with the arising amount of quinoline. And when the volume ratio between quinolone and coal tar was 20:1 and the temperature was 45 °C. The viscosity of three layers decreased first and then increased with the prolonging of static time. And when the static time of coal tar was 24 h, the viscosity of coal tar is the lowest. Because of the lower viscosity of coal tar, decreasing the content of carbon and ash particles in upper and middle layer, the ash content decreased from 0.168% to 0.092%. The addition of Zn(OH)2 can lead ash content in middle layer decrease to 0.058%. Zn2SiO4 and ZnAl2O4 may be produced due to the reaction between Zn (OH) 2 and SiO2 or Al2O3, which can settle down easily. The results show that the content of carbon and inorganic oxide particles in upper-middle-class (the middle 4/5 of the whole volume) decreased with the addition of quinolone and Zn(OH)2 . When the volume ratio between quinolone and coal tar was 50:2, quality ratio between coal tar and Zn(OH)2 was 20000:1, the mixture were heated up to 45 °C at atmospheric pressure and keeping this constant temperature for 24 h, the ash content in upper-middle-class can decreased to 0.058%. (author)

Influence of Temperature on Corrosion Behavior of 2A02 Al Alloy in Marine Atmospheric Environments

Directory of Open Access Journals (Sweden)

Min Cao

2018-02-01

Full Text Available The corrosion behavior of 2A02 Al alloy under 4 mg/cm2 NaCl deposition at different temperatures (from 30 to 80 °C has been studied. This corrosion behavior was researched using mass-gain, scanning electron microscopy-SEM, laser scanning confocal microscopy-LSCM, X-ray photoelectron spectroscopy-XPS and other techniques. The results showed and revealed that the corrosion was maximal at 60 °C after 200 h of exposure. The increase of temperature not only affected the solubility of oxygen gas in the thin film, but also promoted the transport of ions (such as Cl−, and the formation of protective AlO(OH, which further affects the corrosion speed.

Influence of Temperature on Corrosion Behavior of 2A02 Al Alloy in Marine Atmospheric Environments

Science.gov (United States)

Cao, Min; Liu, Li; Fan, Lei; Yu, Zhongfen; Li, Ying; Oguzie, Emeka E.; Wang, Fuhui

2018-01-01

The corrosion behavior of 2A02 Al alloy under 4 mg/cm2 NaCl deposition at different temperatures (from 30 to 80 °C) has been studied. This corrosion behavior was researched using mass-gain, scanning electron microscopy-SEM, laser scanning confocal microscopy-LSCM, X-ray photoelectron spectroscopy-XPS and other techniques. The results showed and revealed that the corrosion was maximal at 60 °C after 200 h of exposure. The increase of temperature not only affected the solubility of oxygen gas in the thin film, but also promoted the transport of ions (such as Cl−), and the formation of protective AlO(OH), which further affects the corrosion speed. PMID:29401690

Obesity hypoventilation syndrome (OHS)

Science.gov (United States)

... this page: //medlineplus.gov/ency/article/000085.htm Obesity hypoventilation syndrome (OHS) To use the sharing features on this page, please enable JavaScript. Obesity hypoventilation syndrome (OHS) is a condition in some ...

OH, HO2 and RO2 Radical and OH Reactivity Observations during the Summertime in Beijing: High In-Situ Ozone Production and Evidence of a Missing OH Source.

Science.gov (United States)

Whalley, L.; Ye, C.; Slater, E.; Woodward-Massey, R.; Lee, J. D.; Squires, F. A.; Hopkins, J. R.; Dunmore, R.; Shaw, M.; Hamilton, J.; Lewis, A. C.; Crilley, L.; Kramer, L. J.; Bloss, W.; Heard, D. E.

2017-12-01

Despite substantial reductions in primary emissions of pollutants in China over the past decade, concentrations of the secondary pollutant, ozone, still frequently exceed air quality threshold limits in urban areas during the summertime. We will present measurements of OH, HO2 and RO2 radicals and OH reactivity made in central Beijing at the Institute of Atmospheric Physics of the Chinese Academy of Sciences, close to the North 4th ring road in May and June 2017 which formed the summer phase of `An Integrated Study of AIR Pollution PROcesses'. Elevated levels of O3 (>100 ppbv) were regularly observed. NO concentrations were elevated during the morning but often decreased to below the instrument limit of detection during the afternoon hours when the ozone concentrations peaked. Biogenic emissions influenced the chemistry at the site, with several ppbv of isoprene measured during the afternoons. The OH measurements were made using the FAGE technique, equipped with an inlet pre injector (IPI) which provides an alternative method to determine the instrument background signal by injecting a scavenger to remove ambient OH and ensures an artefact-free OH measurement. Elevated levels of OH were observed, with a mean peak OH concentration of 1.2×107 molecule cm-3 at noon; but with OH concentrations reaching up to 2.5×107 molecule cm-3 on some days. Mean peak HO2 concentrations of 3×108 molecule cm-3 and total RO2 of 1.2×109 molecule cm-3 were recorded, with maximum concentrations of 1.0×109 molecule cm-3 and 4×109 molecule cm-3 observed for HO2 and RO2 respectively, suggesting significant in situ ozone production. A comparison of the artefact-free OH observations with steady state calculations, constrained to the total OH reactivity measurement and known OH precursors that were measured alongside OH, highlights a significant missing daytime OH source under low [NO], with the steady state OH concentrations approximately a factor of two lower than the OH concentrations

Bulk modulus of basic sodalite, Na8[AlSiO4]6(OH)2·2H2O, a possible zeolitic precursor in coal-fly-ash-based geopolymers

KAUST Repository

Oh, Jae Eun

2011-01-01

Synthetic basic sodalite, Na8[AlSiO4] 6(OH)2•2H2O, cubic, P43n, (also known as hydroxysodalite hydrate) was prepared by the alkaline activation of amorphous aluminosilicate glass, obtained from the phase separation of Class F fly ash. The sample was subjected to a process similar to geopolymerization, using high concentrations of a NaOH solution at 90 °C for 24 hours. Basic sodalite was chosen as a representative analogue of the zeolite precursor existing in Na-based Class F fly ash geopolymers. To determine its bulk modulus, high-pressure synchrotron X-ray powder diffraction was applied using a diamond anvil cell (DAC) up to a pressure of 4.5 GPa. A curve-fit with a truncated third-order Birch-Murnaghan equation of state with a fixed K\\'o = 4 to pressure-normalized volume data yielded the isothermal bulk modulus, K o = 43 ± 4 GPa, indicating that basic sodalite is more compressible than sodalite, possibly due to a difference in interactions between the framework host and the guest molecules. © 2010 Elsevier Ltd.

Hydrogen migration dynamics in hydrated Al clusters: The Al{sub 17}{sup (−)}·H{sub 2}O system as an example

Energy Technology Data Exchange (ETDEWEB)

Álvarez-Barcia, S.; Flores, J. R., E-mail: flores@uvigo.es [Facultad de Química, Universidad de Vigo, E-36310-Vigo (Pontevedra) (Spain)

2014-02-28

The Al{sub m}{sup (−)}·(H{sub 2}O){sub n} systems are known to undergo water splitting processes in the gas phase giving H{sub k}Al{sub m}(OH){sub k}{sup (−)}·(H{sub 2}O){sub n−k} systems, which can generate H{sub 2}. The migration of H atoms from one Al atom to another on the cluster's surface is of critical importance to the mechanism of the complete H{sub 2} production process. We have applied a combination of Molecular Dynamics and Rice-Ramsperger-Kassel-Marcus theory including tunneling effects to study the gas-phase evolution of HAl{sub 17}(OH){sup (−)}, which can be considered a model system. First, we have performed an extensive search for local minima and the connecting saddle points using a density functional theory method. It is found that in the water-splitting process Al{sub 17}{sup (−)}·(H{sub 2}O) → HAl{sub 17}(OH){sup (−)}, the H atom which bonds to the Al cluster losses rather quickly its excess energy, which is easily “absorbed” by the cluster because of its flexibility. This fact ultimately determines that long-range hydrogen migration is not a very fast process and that, probably, tunneling only plays a secondary role in the migration dynamics, at least for moderate energies. Reduction of the total energy results in the process being very much slowed down. The consequences on the possible mechanisms of H{sub 2} generation from the interaction of Al clusters and water molecules are discussed.

Effect of 24,25-dihydroxyvitamin D3 on 1,25-dihydroxyvitamin D3 [1,25-(OH)2D3] metabolism in vitamin D-deficient rats infused with 1,25-(OH)2D3

International Nuclear Information System (INIS)

Yamato, H.; Matsumoto, T.; Fukumoto, S.; Ikeda, K.; Ishizuka, S.; Ogata, E.

1989-01-01

Previous studies revealed that administration of 24,25-dihydroxyvitamin D3 [24,25-(OH)2D3] to calcium (Ca)-deficient rats causes a dose-dependent reduction in markedly elevated serum 1,25-(OH)2D3 level. Although the results suggested that the metabolism of 1,25-(OH)2D3 was accelerated by 24,25-(OH)2D3, those experiments could not define whether the enhanced metabolism of 1,25-(OH)2D3 played a role in the reduction in the serum 1,25-(OH)2D3 level. In the present study, in order to address this issue more specifically, serum 1,25-(OH)2D3 was maintained solely by exogenous administration through miniosmotic pumps of 1,25-(OH)2D3 into vitamin D-deficient rats. Thus, by measuring the serum 1,25-(OH)2D3 concentration, the effect of 24,25-(OH)2D3 on the MCR of 1,25-(OH)2D3 could be examined. Administration of 24,25-(OH)2D3 caused a dose-dependent enhancement in the MCR of 1,25-(OH)2D3, and 1 microgram/100 g rat.day 24,25-(OH)2D3, which elevated serum 24,25-(OH)2D3 to 8.6 +/- 1.3 ng/ml, significantly increased MCR and suppressed serum levels of 1,25-(OH)2D3. The effect of 24,25-(OH)2D3 on 1,25-(OH)2D3 metabolism developed with a rapid time course, and the recovery of iv injected [1 beta-3H]1,25-(OH)2D3 in blood was significantly reduced within 1 h. In addition, there was an increase in radioactivity in the water-soluble fraction of serum as well as in urine, suggesting that 1,25-(OH)2D3 is rapidly degraded to a water-soluble metabolite(s). Furthermore, the reduction in serum 1,25-(OH)2D3 was associated with a reduction in both serum and urinary Ca levels. Because the conversion of [3H]24,25-(OH)2D3 to [3H]1,24,25-(OH)2D3 or other metabolites was minimal in these rats, 24,25-(OH)2D3 appears to act without being converted into other metabolites. These results demonstrate that 24,25-(OH)2D3 rapidly stimulates the metabolism of 1,25-(OH)2D3 and reduces its serum level

Widespread distribution of OH/H2O on the lunar surface inferred from spectral data.

Science.gov (United States)

Bandfield, Joshua L; Poston, Michael J; Klima, Rachel L; Edwards, Christopher S

2018-01-01

Remote sensing data from lunar orbiters have revealed spectral features consistent with the presence of OH or H 2 O on the lunar surface. Analyses of data from the Moon Mineralogy Mapper spectrometer onboard the Chandryaan-1 spacecraft have suggested that OH/H 2 O is recycled on diurnal timescales and persists only at high latitudes. However, the spatial distribution and temporal variability of the OH/H 2 O, as well as its source, remain uncertain. Here we incorporate a physics-based thermal correction into analysis of reflectance spectra from the Moon Mineralogy Mapper and find that prominent absorption features consistent with OH/H 2 O can be present at all latitudes, local times, and surface types examined. This suggests the widespread presence of OH/H 2 O on the lunar surface without significant diurnal migration. We suggest that the spectra are consistent with the production of OH in space weathered materials by the solar wind implantation of H + and formation of OH at crystal defect sites, as opposed to H 2 O sourced from the lunar interior. Regardless of the specific composition or formation mechanism, we conclude that OH/H 2 O can be present on the Moon under thermal conditions more wide-ranging than previously recognized.

Oh No, Henrietta Got Out!

Science.gov (United States)

Lottero-Perdue, Pamela; Grabia, Kathryn; Sandifer, Cody

2017-01-01

In a kindergarten classroom, exclamations like "Oh no!" may be causes for concern. However, when the students in Mrs. Grabia's classroom shouted "Oh no!" and "Uh oh!" during an engineering-infused 5E lesson, it meant that a persistent little robot had pushed its way out of the fences they had created. It also meant…

Cation incorporation into zirconium oxide in LiOH, NaOH, and KOH solutions

International Nuclear Information System (INIS)

Jeong, Y.H.; Kim, K.H.; Baek, J.H.

1999-01-01

To investigate the cation incorporation into zirconium oxide, SIMS analysis was performed on the specimens prepared to have an equal oxide thickness in LiOH, NaOH, and KOH solutions. Even though they have an equal oxide thickness in LiOH, NaOH, and KOH solutions, the penetration depth of cation into the oxide decreased with an increase in the ionic radius of cation. The cation is considered to control the corrosion in alkali hydroxide solutions and its effect is dependent on the concentration of alkali and the oxide thickness. The slight enhancement of the corrosion rate at a low concentration is thought to be caused by cation incorporation into oxide, while the significant acceleration at a high concentration is due to the transformation of oxide microstructures that would be also induced by cation incorporation into oxide. (orig.)

CuSn(OH)6 submicrospheres: Room-temperature synthesis, growth mechanism, and weak antiferromagnetic behavior

International Nuclear Information System (INIS)

Zhong, Sheng-Liang; Xu, Rong; Wang, Lei; Li, Yuan; Zhang, Lin-Fei

2011-01-01

Highlights: ► CuSn(OH) 6 spheres have been synthesized via an aqueous solution method at room temperature. ► The diameters of the CuSn(OH) 6 spheres can be tuned by adjusting the molar ratio of SnO 3 2− to Cu 2+ . ► The as-obtained CuSn(OH) 6 spheres are antiferromagnetic and have a weak spin-Peierls transition at about 78 K -- Abstract: CuSn(OH) 6 submicrospheres with diameters of 400–900 nm have been successfully fabricated using a simple aqueous solution method at room temperature. Influencing factors such as the dosage of reactants and reaction time on the preparation were systematically investigated. The products were characterized with X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TG) and differential thermal analysis (DTA). Results reveal that the CuSn(OH) 6 spheres are built from numerous nanoparticles. It is found that the diameter of CuSn(OH) 6 spheres can be readily tuned by adjusting the molar ratio of SnO 3 2− to Cu 2+ . A possible growth mechanism for the CuSn(OH) 6 submicrospheres has been proposed. Amorphous CuSnO 3 submicrospheres were obtained after thermal treatment of the CuSn(OH) 6 submicrospheres at 300 °C for 4 h. Standard magnetization measurements demonstrate that the CuSn(OH) 6 submicrospheres are antiferromagnetic and have a weak spin-Peierls transition at about 78 K.

Sorptive stabilization of organic matter by amorphous Al hydroxide

NARCIS (Netherlands)

Schneider, M.P.W.; Scheel, T.; Mikutta, R.; van Hees, P.; Kaiser, K.; Kalbitz, K.

2010-01-01

Amorphous Al hydroxides (am-Al(OH)(3)) strongly sorb and by this means likely protect dissolved organic matter (OM) against microbial decay in soils. We carried out batch sorption experiments (pH 4.5; 40 mg organic C L-1) with OM extracted from organic horizons under a Norway spruce and a European

The Attitude of Construction Workers toward the Implementation of Occupational Health and Safety (OHS)

Science.gov (United States)

Widaningsih, L.; Susanti, I.; Chandra, T.

2018-02-01

Construction industry refers to one of the industries dealing with high accident rate. Besides its outdoor workplace involving many workers who usually work manually, the workers’ work culture and less awareness of occupational health and safety (OHS) are attributed to the high accident rate. This study explores some construction workers who are involved in some construction projects in big cities such as Bandung and Jakarta. The questionnaire-given to the construction workers focusing on stone construction, wood construction, and finishing session-reveals that the construction workers knowledge and understanding of nine Occupational Health and Safety (OHS) aspects reach above 50%. However, does not appear to reflect their knowledge and understanding of Occupational Health and Safety (OHS). The results of Focus Group Discussion (FGD) and an in-depth interview show that the fallacious implementation of Occupational Health and Safety (OHS) is attributed to their traditional “work culture”.

Environmental sciences: general. 2. Water Adsorption/Absorption by CsOH Particles

International Nuclear Information System (INIS)

Riggs, C.A.; Ghosh, T.K.; Tompson, R.V.; Loyalka, S.K.; Viswanath, D.S.

2001-01-01

Cesium hydroxide in aerosol form is likely to be a significant source of radio-cesium released during a reactor transient. Cesium hydroxide particles are hydrophilic and absorb/adsorb water rapidly. The result is a rapid growth of cesium hydroxide wetted agglomerates that can deposit on surfaces by gravitational settling. However, they can also react with iodine gas to form CsI according to Eq. (1). The rapid absorption/adsorption of water by CsOH may increase the rate of absorption of iodine by CsOH. Iodine may attach itself to adsorbed water molecules on CsOH and facilitate the reaction by bringing iodine to CsOH. Thus, the iodine removal mechanism from the pressurized water reactor containment atmosphere may change: I 2(g) + 4CsOH (s) ↔ 2CsI (s) + 2CsO (s) + 2H 2 O (l) . (1) Despite the importance of CsOH as an aerosol material released during a reactor transient, we have been unable to find any isotherm data of water on cesium hydroxide in the literature. The significant hydrophilic nature of CsOH, together with its being the strongest base currently known, present challenges to collection of water adsorption data. The objective in this research was to experimentally obtain isotherm data of water vapor on CsOH for a range of temperatures and pressures on macroscopic samples using an electro-balance. These data then may be used to predict the amount of water vapor adsorbed on CsOH at other temperatures and pressures by existing models. The adsorption apparatus using a Cahn 2000 electro-balance is shown in Fig. 1. The water adsorption/absorption data on CsOH at different relative pressures of water vapor were obtained gravimetrically. A detailed description of the experimental system is given in Hassan et al. An∼70-mg sample of CsOH.H 2 O (s) was placed onto a platinum weighing dish in the hang-down tube of the balance. The sample was regenerated by heating it at 100 deg. C under a vacuum of 3.5x10 -2 mm Hg for 24 h to remove adsorbed water and other gases

Photoionization of the OH radical

International Nuclear Information System (INIS)

Dehmer, P.M.

1985-01-01

The hydroxyl radical (OH) is one of the most thoroughly studied free radicals because of its importance in atmospheric chemistry, combustion processes, and the interstellar medium. Detailed experimental and theoretical studies have been performed on the ground electronic state (X 2 PI/sub i/) and on the four lowest bound excited electronic states (A 2 Σ + , B 2 Σ + , D 2 Σ - , and C 2 Σ + ). However, because it is difficult to distinguish the spectrum of OH from the spectra of the various radical precursors, the absorption spectrum in the wavelength region below 1200 A has not been well characterized. In the present work, the spectrum of OH has been determined in the wavelength region from 750 to 950 A using the technique of photoionization mass spectrometry. This technique allows complete separation of the spectrum of OH from that of the other components of the discharge and permits the unambiguous determination of the spectrum of OH

High-temperature rate constant measurements for OH+xylenes

KAUST Repository

Elwardani, Ahmed Elsaid

2015-06-01

The overall rate constants for the reactions of hydroxyl (OH) radicals with o-xylene (k 1), m-xylene (k 2), and p-xylene (k 3) were measured behind reflected shock waves over 890-1406K at pressures of 1.3-1.8atm using OH laser absorption near 306.7nm. Measurements were performed under pseudo-first-order conditions. The measured rate constants, inferred using a mechanism-fitting approach, can be expressed in Arrhenius form as:k1=2.93×1013exp(-1350.3/T)cm3mol-1s-1(890-1406K)k2=3.49×1013exp(-1449.3/T)cm3mol-1s-1(906-1391K)k3=3.5×1013exp(-1407.5/T)cm3mol-1s-1(908-1383K)This paper presents, to our knowledge, first high-temperature measurements of the rate constants of the reactions of xylene isomers with OH radicals. Low-temperature rate-constant measurements by Nicovich et al. (1981) were combined with the measurements in this study to obtain the following Arrhenius expressions, which are applicable over a wider temperature range:k1=2.64×1013exp(-1181.5/T)cm3mol-1s-1(508-1406K)k2=3.05×109exp(-400/T)cm3mol-1s-1(508-1391K)k3=3.0×109exp(-440/T)cm3mol-1s-1(526-1383K) © 2015 The Combustion Institute.

Determinants of 25(OH)D sufficiency in obese minority children: selecting outcome measures and analytic approaches.

Science.gov (United States)

Zhou, Ping; Schechter, Clyde; Cai, Ziyong; Markowitz, Morri

2011-06-01

To highlight complexities in defining vitamin D sufficiency in children. Serum 25-(OH) vitamin D [25(OH)D] levels from 140 healthy obese children age 6 to 21 years living in the inner city were compared with multiple health outcome measures, including bone biomarkers and cardiovascular risk factors. Several statistical analytic approaches were used, including Pearson correlation, analysis of covariance (ANCOVA), and "hockey stick" regression modeling. Potential threshold levels for vitamin D sufficiency varied by outcome variable and analytic approach. Only systolic blood pressure (SBP) was significantly correlated with 25(OH)D (r = -0.261; P = .038). ANCOVA revealed that SBP and triglyceride levels were statistically significant in the test groups [25(OH)D 25 ng/mL]. ANCOVA also showed that only children with severe vitamin D deficiency [25(OH)D model regression analyses found evidence of a threshold level in SBP, with a 25(OH)D breakpoint of 27 ng/mL, along with a 25(OH)D breakpoint of 18 ng/mL for triglycerides, but no relationship between 25(OH)D and parathyroid hormone. Defining vitamin D sufficiency should take into account different vitamin D-related health outcome measures and analytic methodologies. Copyright © 2011 Mosby, Inc. All rights reserved.

PCLI2/Ca(OH)2 bioactive composite for endodontic treatment

International Nuclear Information System (INIS)

Almeida, Kleberde Arruda; Caniello, Thylander Magno; Alencar de Queiroz, Alvaro Antonio

2004-01-01

The use of biodegradable macroporous polymer-ceramic composites in treating bone defects has become widely used in clinical practice. In this work, the synthesis and characterization of the composite poly(ε-caprolactone)-iodine/calcium hydroxide (PCLI 2 /Ca(OH) 2 ), developed for endodontic therapy are presented. The composite was obtained by the ring opening of the ε-caprolactone monomer using iodine (I 2 ) as catalyst. The microstructural analysis by scanning electron microscopy (SEM) indicates that the composite PCLI 2 /Ca(OH) 2 has a macroporous sponge-like structure. The biodegradable composite showed excellent antimicrobial activities against Escherichia coli and Staphylococcus aureus. The X-ray radiography of the implanted composite revealed a good adhesion in the root canal and excellent radiopacity

A Shock Tube Study of the CO + OH Reaction Near the Low-Pressure Limit

KAUST Repository

Nasir, Ehson Fawad; Farooq, Aamir

2016-01-01

Rate coefficients for the reaction between carbon monoxide and hydroxyl radical were measured behind reflected shock waves over 700 – 1230 K and 1.2 – 9.8 bar. The temperature/pressure conditions correspond to the predicted low-pressure limit of this reaction, where the channel leading to carbon dioxide formation is dominant. The reaction rate coefficients were inferred by measuring the formation of carbon dioxide using quantum cascade laser absorption near 4.2 µm. Experiments were performed under pseudo-first order conditions with tert-butyl hydroperoxide (TBHP) as the OH precursor. Using ultraviolet laser absorption by OH radicals, the TBHP decomposition rate was measured to quantify potential facility effects under extremely dilute conditions used here. The measured CO + OH rate coefficients are provided in Arrhenius form for three different pressure ranges: kCO+OH (1.2 – 1.6 bar) = 9.14 x 10-13 exp(-1265/T) cm3 molecule-1 s-1 kCO+OH (4.3 – 5.1 bar) = 8.70 x 10-13 exp(-1156/T) cm3 molecule-1 s-1 kCO+OH (9.6 – 9.8 bar) = 7.48 x 10-13 exp(-929/T) cm3 molecule-1 s-1 The measured rate coefficients are found to be lower than the master equation modeling results by Weston et al. [J. Phys. Chem. A, 117 (2013) 821] at 819 K and in closer agreement with the expression provided by Joshi and Wang [Int. J. Chem. Kinet., 38 (2006) 57].

A Shock Tube Study of the CO + OH Reaction Near the Low-Pressure Limit

KAUST Repository

Nasir, Ehson Fawad

2016-05-16

Rate coefficients for the reaction between carbon monoxide and hydroxyl radical were measured behind reflected shock waves over 700 – 1230 K and 1.2 – 9.8 bar. The temperature/pressure conditions correspond to the predicted low-pressure limit of this reaction, where the channel leading to carbon dioxide formation is dominant. The reaction rate coefficients were inferred by measuring the formation of carbon dioxide using quantum cascade laser absorption near 4.2 µm. Experiments were performed under pseudo-first order conditions with tert-butyl hydroperoxide (TBHP) as the OH precursor. Using ultraviolet laser absorption by OH radicals, the TBHP decomposition rate was measured to quantify potential facility effects under extremely dilute conditions used here. The measured CO + OH rate coefficients are provided in Arrhenius form for three different pressure ranges: kCO+OH (1.2 – 1.6 bar) = 9.14 x 10-13 exp(-1265/T) cm3 molecule-1 s-1 kCO+OH (4.3 – 5.1 bar) = 8.70 x 10-13 exp(-1156/T) cm3 molecule-1 s-1 kCO+OH (9.6 – 9.8 bar) = 7.48 x 10-13 exp(-929/T) cm3 molecule-1 s-1 The measured rate coefficients are found to be lower than the master equation modeling results by Weston et al. [J. Phys. Chem. A, 117 (2013) 821] at 819 K and in closer agreement with the expression provided by Joshi and Wang [Int. J. Chem. Kinet., 38 (2006) 57].

Evaluation of alkaline dissolution of Al 6061 and Al 1050 for the production of Mo-99 from LEU targets

International Nuclear Information System (INIS)

Mindrisz, Ana C.; Camilo, Ruth L.; Araujo, Izilda C.; Forbicini, Christina A.L.G. de O.

2013-01-01

Since 2008, due to the global crisis in the production of radioisotope 99 Mo, which product of decay, 99m Tc, is the tracer element most often used in nuclear medicine and accounts for about 80% of all diagnostic procedures in vivo. Studies on the alkaline dissolution to obtain 9 9M o from irradiated UAl x -Al LEU targets are under development. Processing time should be minimized, considering the short half-life of 99 Mo and 99m Tc, about 66 h and 6 h, respectively. This makes dissolution time a significant factor in the development of the process. This paper presents the results of alkaline dissolution of 'scraps' of Al 6061 and 1050, used to simulate the dissolution process of UAl x -Al targets. Dissolution time and gas releasing were evaluated using the following alkaline solutions: a) NaOH 3 mol.L -1 and NaNO 3 2 mol.L -1 , b) NaOH 3 mol.L -1 and NaNO 3 4 mol.L -1 . The initial temperature of dissolution was 85 deg C in all cases. Al 6061 showed values of dissolution time greater than that for Al 1050, 25% for NaNO 3 2 mol.L -1 and 104.55% for NaNO 3 4 mol.L -1 . The dissolution with NaNO 3 2 mol.L -1 showed that the gas releasing for Al 6061 was 2.7% greater than for Al 1050. However Al 1050 showed that gas releasing 9.92% greater than for Al 6061 during the dissolution with NaNO 3 4 mol.L -1 . The decision about what type of alloy has to be used, Al 1050 or Al 6061, it will be upto the group that will manufacture the targets for the RMB. (author)

Global modelling of the total OH reactivity: investigations on the “missing” OH sink and its atmospheric implications

Directory of Open Access Journals (Sweden)

V. Ferracci

2018-05-01

Full Text Available The hydroxyl radical (OH plays a crucial role in the chemistry of the atmosphere as it initiates the removal of most trace gases. A number of field campaigns have observed the presence of a missing OH sink in a variety of regions across the planet. A comparison of direct measurements of the OH loss frequency, also known as total OH reactivity (kOH, with the sum of individual known OH sinks (obtained via the simultaneous detection of species such as volatile organic compounds and nitrogen oxides indicates that, in some cases, up to 80 % of kOH is unaccounted for. In this work, the UM-UKCA chemistry-climate model was used to investigate the wider implications of the missing reactivity on the oxidising capacity of the atmosphere. Simulations of the present-day atmosphere were performed and the model was evaluated against an array of field measurements to verify that the known OH sinks were reproduced well, with a resulting good agreement found for most species. Following this, an additional sink was introduced to simulate the missing OH reactivity as an emission of a hypothetical molecule, X, which undergoes rapid reaction with OH. The magnitude and spatial distribution of this sink were underpinned by observations of the missing reactivity. Model runs showed that the missing reactivity accounted for on average 6 % of the total OH loss flux at the surface and up to 50 % in regions where emissions of the additional sink were high. The lifetime of the hydroxyl radical was reduced by 3 % in the boundary layer, whilst tropospheric methane lifetime increased by 2 % when the additional OH sink was included. As no OH recycling was introduced following the initial oxidation of X, these results can be interpreted as an upper limit of the effects of the missing reactivity on the oxidising capacity of the troposphere. The UM-UKCA simulations also allowed us to establish the atmospheric implications of the newly characterised reactions of peroxy

Hydrogen Generation from Al-NiCl2/NaBH4 Mixture Affected by Lanthanum Metal

Directory of Open Access Journals (Sweden)

Wen Qiang Sun

2012-01-01

Full Text Available The effect of La on Al/NaBH4 hydrolysis was elaborated in the present paper. Hydrogen generation amount increases but hydrogen generation rate decreases with La content increasing. There is an optimized composition that Al-15 wt% La-5 wt% NiCl2/NaBH4 mixture (Al-15 wt% La-5 wt% NiCl2/NaBH4 weight ratio, 1 : 3 has 126 mL g−1 min−1 maximum hydrogen generation rate and 1764 mL g−1 hydrogen generation amount within 60 min. The efficiency is 88%. Combined with NiCl2, La has great effect on NaBH4 hydrolysis but has little effect on Al hydrolysis. Increasing La content is helpful to decrease the particle size of Al-La-NiCl2 in the milling process, which induces that the hydrolysis byproduct Ni2B is highly distributed into Al(OH3 and the catalytic reactivity of Ni2B/Al(OH3 is increased therefore. But hydrolysis byproduct La(OH3 deposits on Al surface and leads to some side effect. The Al-La-NiCl2/NaBH4 mixture has good stability in low temperature and its hydrolytic performance can be improved with increasing global temperature. Therefore, the mixture has good safety and can be applied as on board hydrogen generation material.

Hydrogen generation from Al-NiCl2/NaBH4 mixture affected by lanthanum metal.

Science.gov (United States)

Sun, Wen Qiang; Fan, Mei-Qiang; Fei, Yong; Pan, Hua; Wang, Liang Liang; Yao, Jun

2012-01-01

The effect of La on Al/NaBH(4) hydrolysis was elaborated in the present paper. Hydrogen generation amount increases but hydrogen generation rate decreases with La content increasing. There is an optimized composition that Al-15 wt% La-5 wt% NiCl(2)/NaBH(4) mixture (Al-15 wt% La-5 wt% NiCl(2)/NaBH(4) weight ratio, 1 : 3) has 126 mL g(-1 )min(-1) maximum hydrogen generation rate and 1764 mL g(-1) hydrogen generation amount within 60 min. The efficiency is 88%. Combined with NiCl(2), La has great effect on NaBH(4) hydrolysis but has little effect on Al hydrolysis. Increasing La content is helpful to decrease the particle size of Al-La-NiCl(2) in the milling process, which induces that the hydrolysis byproduct Ni(2)B is highly distributed into Al(OH)(3) and the catalytic reactivity of Ni(2)B/Al(OH)(3) is increased therefore. But hydrolysis byproduct La(OH)(3) deposits on Al surface and leads to some side effect. The Al-La-NiCl(2)/NaBH(4) mixture has good stability in low temperature and its hydrolytic performance can be improved with increasing global temperature. Therefore, the mixture has good safety and can be applied as on board hydrogen generation material.

Resonant ion-pair formation in electron collisions with HD+ and OH+

International Nuclear Information System (INIS)

Larson, Aa.; Djuric, N.; Zong, W.; Greene, C. H.; Orel, A. E.; Al-Khalili, A.; Derkatch, A. M.; Le Padellec, A.; Neau, A.; Rosen, S.

2000-01-01

Resonant ion-pair formation from collisions of electrons with electronic and vibronic ground-state diatomic molecular ions has been studied in the present work for HD + and OH + . The cross section for HD + has a magnitude of the order of 3x10 -19 cm 2 and is characterized by an energy threshold and 14 resolved peaks in the energy range up to 16 eV. A theoretical study confirms that the structures derive primarily from quantum interference of the multiple dissociation pathways. Measurements for OH + reveal that the cross section for H + and O - formation is lower than 10 -21 cm 2 at energies of 6 and 12 eV. (c) 2000 The American Physical Society

Chemical failure modes of AlQ3-based OLEDs: AlQ3 hydrolysis.

Science.gov (United States)

Knox, John E; Halls, Mathew D; Hratchian, Hrant P; Schlegel, H Bernhard

2006-03-28

Tris(8-hydroxyquinoline)aluminum(III), AlQ3, is used in organic light-emitting diodes (OLEDs) as an electron-transport material and emitting layer. The reaction of AlQ3 with trace H2O has been implicated as a major failure pathway for AlQ3-based OLEDs. Hybrid density functional calculations have been carried out to characterize the hydrolysis of AlQ3. The thermochemical and atomistic details for this important reaction are reported for both the neutral and oxidized AlQ3/AlQ3+ systems. In support of experimental conclusions, the neutral hydrolysis reaction pathway is found to be a thermally activated process, having a classical barrier height of 24.2 kcal mol(-1). First-principles infrared and electronic absorption spectra are compared to further characterize AlQ3 and the hydrolysis pathway product, AlQ2OH. The activation energy for the cationic AlQ3 hydrolysis pathway is found to be 8.5 kcal mol(-1) lower than for the neutral reaction, which is significant since it suggests a role for charge imbalance in promoting chemical failure modes in OLED devices.

Smectite flocculation structure modified by Al13 macro-molecules--as revealed by the transmission X-ray microscopy (TXM).

Science.gov (United States)

Zbik, Marek S; Martens, Wayde N; Frost, Ray L; Song, Yen-Fang; Chen, Yi-Ming; Chen, Jian-Hua

2010-05-01

The aggregate structure which occurs in aqueous smectitic suspensions is responsible for poor water clarification, difficulties in sludge dewatering and the unusual rheological behaviour of smectite rich soils. These macroscopic properties are dictated by the 3D structural arrangement of smectite finest fraction within flocculated aggregates. Here, we report results from a relatively new technique, transmission X-ray microscopy (TXM), which makes it possible to investigate the internal structure and 3D tomographic reconstruction of the smectite clay aggregates modified by Al(13) Keggin macro-molecule [Al(13)(O)(4)(OH)(24)(H(2)O)(12)](7+). Three different treatment methods were shown resulted in three different micro-structural environments of the resulting flocculation. In case of smectite sample prepared in Methods 1 and 3 particles fall into the primary minimum where Van der Waals forces act between FF oriented smectite flakes and aggregates become approach irreversible flocculation. In case of sample prepared using Method 2, particles contacting by edges (EE) and edge to face (EF) orientation fell into secondary minimum and weak flocculation resulted in severe gelation and formation of the micelle-like texture in fringe superstructure, which was first time observed in smectite based gel. Copyright 2010 Elsevier Inc. All rights reserved.

Mechanism and kinetic properties for the OH-initiated atmospheric oxidation degradation of 9,10-Dichlorophenanthrene.

Science.gov (United States)

Dang, Juan; Shi, Xiangli; Zhang, Qingzhu; Hu, Jingtian; Wang, Wenxing

2015-02-01

Chlorinated polycyclic aromatic hydrocarbons (ClPAHs) have become a serious environmental concern due to their widespread occurrence and dioxin-like toxicities. In this work, the mechanism of the OH-initiated atmospheric oxidation degradation of 9,10-dichlorophenanthrene (9,10-Cl₂Phe) was investigated by using high-accuracy quantum chemistry calculations. The rate constants of the crucial elementary reactions were determined by the Rice-Ramsperger-Kassel-Marcus (RRKM) theory. The theoretical results were compared with the available experimental data. The main oxidation products are a group of ring-retaining and ring-opening compounds including chlorophenanthrols, 9,10-dichlorophenanthrene-3,4-dione, dialdehydes, chlorophenanthrenequinones, nitro-9,10-Cl₂Phe and epoxides et al. The overall rate constant of the OH addition reaction is 2.35 × 10(-12)cm(3) molecule(-1)s(-1) at 298 K and 1 atm. The atmospheric lifetime of 9,10-Cl₂Phe determined by OH radicals is about 5.05 days. This study provides a comprehensive investigation of the OH-initiated oxidation degradation of 9,10-Cl₂Phe and should contribute to clarifying its atmospheric fate. Copyright © 2014 Elsevier B.V. All rights reserved.

Solid-State Synthesis and Structure of the Enigmatic Ammonium Octaborate: (NH4)2[B7O9(OH)5]·3/4B(OH)3·5/4H2O.

Science.gov (United States)

Neiner, Doinita; Sevryugina, Yulia V; Schubert, David M

2016-09-06

The compound known since the 19th century as ammonium octaborate was structurally characterized revealing the ammonium salt of the ribbon isomer of the heptaborate anion, [B7O9(OH)5](2-), with boric acid and water molecules. Of composition (NH4)2B7.75O12.63·4.88H2O, it approximates the classical ammonium octaborate composition (NH4)2B8O13·6H2O and has the structural formula {(NH4)2[B7O9(OH)5]}4·3B(OH)3·5H2O. It spontaneously forms at room temperature in solid-state mixtures of ammonium tetraborate and ammonium pentaborate. It crystallizes in the monoclinic space group P21/c with a = 11.4137(2) Å, b = 11.8877(2) Å, c = 23.4459(3) Å, β = 90.092(1)°, V = 3181.19(8) Å(3), and Z = 2 and contains well-ordered ammonium cations and [B7O9(OH)5](2-) anions and disordered B(OH)3 and H2O molecules linked by extensive H bonding. Expeditious solid-state formation of the heptaborate anion under ambient conditions has important implications for development of practical syntheses of industrially useful borates.

Redetermination of the cubic struvite analogue Cs[Mg(OH26](AsO4

Directory of Open Access Journals (Sweden)

Matthias Weil

2009-01-01

Full Text Available In contrast to the previous refinement from photographic data [Ferrari et al. (1955. Gazz. Chim. Ital. 84, 169–174], the present redetermination of the title compound, caesium hexaaquamagnesium arsenate(V, revealed the Cs atom to be on Wyckoff position 4d instead of Wyckoff position 4b of space group Foverline{4}3m. The structure can be derived from the halite structure. The centres of the complex [Mg(OH26] octahedra and the AsO4 tetrahedra (both with overline{4}3m symmetry are on the respective Na and Cl positions. The building units are connected to each other by O—H...O hydrogen bonds. The Cs+ cations (overline{4}3m symmetry are located in the voids of this arrangement and exhibit a regular cuboctahedral 12-coordination to the O atoms of the water molecules. The O atom bonded to As has 2mm site symmetry (Wyckoff position 24f and the water-molecule O atom has m site symmetry (Wyckoff position 48h.

Biodistribution and tumor uptake of C{sub 60}(OH){sub x} in mice

Energy Technology Data Exchange (ETDEWEB)

Zhiqiang, Ji; Sun Hongfang, E-mail: shf@pku.edu.cn; Haifang, Wang; Qunying, Xie; Yuangfang, Liu [Peking University, Department of Chemical Biology, College of Chemistry and Molecular Engineering (China); Zheng, Wang [Chinese Academy of Medical Sciences, Cancer Institute (China)

2006-02-15

Radiolabeling of fullerol, {sup 125}I-C{sub 60}(OH){sub x}, was performed by the traditional chloramine-T method. The C-I covalent bond in I-C{sub 60}(OH){sub x} was characterized by X-ray photoelectron spectroscopy (XPS) that was sufficiently stable for in vivo study. Laser light scattering spectroscopy clearly showed that C{sub 60}(OH){sub x} aggregated to large nanoparticle clumps with a wide range of distribution. The clumps formed were also visualized by transmission electron microscope (TEM). We examined the biodistribution and tumor uptake of C{sub 60}(OH){sub x} in five mouse bearing tumor models, including mouse H22 hepatocarcinoma, human lung giantcellcarcinoma PD, human colon cancer HCT-8, human gastric cancer MGC803, and human OS732 osteosarcoma. The accumulation ratios of {sup 125}I-C{sub 60}(OH){sub x} in mouse H22 hepatocarcinoma to that in normal muscle tissue (T/N) and blood (T/B) at 1, 6, 24 and 72 h, reveal that {sup 125}I-C{sub 60}(OH){sub x} gradually accumulates in H22 tumor, and retains for a quite long period (e.g., T/N 3.41, T/B 3.94 at 24 h). For the other four tumor models, the T/N ratio at 24 h ranges within 1.21-6.26, while the T/B ratio ranges between 1.23 and 4.73. The accumulation of C{sub 60}(OH){sub x} in tumor is mostly due to the enhanced permeability and retention effect (EPR) and the phagocytosis of mononuclear phagocytes. Hence, C{sub 60}(OH){sub x} might serve as a photosensitizer in the photodynamic therapy of some kinds of tumor.

Variability of OH(3-1) and OH(6-2) emission altitude and volume emission rate from 2003 to 2011

Science.gov (United States)

Teiser, Georg; von Savigny, Christian

2017-08-01

In this study we report on variability in emission rate and centroid emission altitude of the OH(3-1) and OH(6-2) Meinel bands in the terrestrial nightglow based on spaceborne nightglow measurements with the SCIAMACHY (SCanning Imaging Absorption spectroMeter for Atmospheric CHartographY) instrument on the Envisat satellite. The SCIAMACHY observations cover the time period from August 2002 to April 2012 and the nighttime observations used in this study are performed at 10:00 p.m. local solar time. Characterizing variability in OH emission altitude - particularly potential long-term variations - is important for an appropriate interpretation of ground-based OH rotational temperature measurements, because simultaneous observations of the vertical OH volume emission rate profile are usually not available for these measurements. OH emission altitude and vertically integrated emission rate time series with daily resolution for the OH(3-1) band and monthly resolution for the OH(6-2) band were analyzed using a standard multilinear regression approach allowing for seasonal variations, QBO-effects (Quasi-Biennial Oscillation), solar cycle (SC) variability and a linear long-term trend. The analysis focuses on low latitudes, where SCIAMACHY nighttime observations are available all year. The dominant sources of variability for both OH emission rate and altitude are the semi-annual and annual variations, with emission rate and altitude being highly anti-correlated. There is some evidence for a 11-year solar cycle signature in the vertically integrated emission rate and in the centroid emission altitude of both the OH(3-1) and OH(6-2) bands.

Coupled growth of Al-Al2Cu eutectics in Al-Cu-Ag alloys

International Nuclear Information System (INIS)

Hecht, U; Witusiewicz, V; Drevermann, A

2012-01-01

Coupled eutectic growth of Al and Al 2 Cu was investigated in univariant Al-Cu-Ag alloys during solidification with planar and cellular morphology. Experiments reveal the dynamic selection of small spacings, below the minimum undercooling spacing and show that distinct morphological features pertain to nearly isotropic or anisotropic Al-Al 2 Cu interfaces.

Effects of Al(OH)O nanoparticle agglomerate size in epoxy resin on tension, bending, and fracture properties

Energy Technology Data Exchange (ETDEWEB)

Jux, Maximilian, E-mail: maximilian.jux@dlr.de [TU Braunschweig, Institute of Adaptronic and Functional Integration (IAF) (Germany); Finke, Benedikt [TU Braunschweig, Institute for Particle Technology (IPAT) (Germany); Mahrholz, Thorsten [DLR Braunschweig, Institute of Composite Structures and Adaptive Systems (FA) (Germany); Sinapius, Michael [TU Braunschweig, Institute of Adaptronic and Functional Integration (IAF) (Germany); Kwade, Arno; Schilde, Carsten [TU Braunschweig, Institute for Particle Technology (IPAT) (Germany)

2017-04-15

Several epoxy Al(OH)O (boehmite) dispersions in an epoxy resin are produced in a kneader to study the mechanistic correlation between the nanoparticle size and mechanical properties of the prepared nanocomposites. The agglomerate size is set by a targeted variation in solid content and temperature during dispersion, resulting in a different level of stress intensity and thus a different final agglomerate size during the process. The suspension viscosity was used for the estimation of stress energy in laminar shear flow. Agglomerate size measurements are executed via dynamic light scattering to ensure the quality of the produced dispersions. Furthermore, various nanocomposite samples are prepared for three-point bending, tension, and fracture toughness tests. The screening of the size effect is executed with at least seven samples per agglomerate size and test method. The variation of solid content is found to be a reliable method to adjust the agglomerate size between 138–354 nm during dispersion. The size effect on the Young’s modulus and the critical stress intensity is only marginal. Nevertheless, there is a statistically relevant trend showing a linear increase with a decrease in agglomerate size. In contrast, the size effect is more dominant to the sample’s strain and stress at failure. Unlike microscaled agglomerates or particles, which lead to embrittlement of the composite material, nanoscaled agglomerates or particles cause the composite elongation to be nearly of the same level as the base material. The observed effect is valid for agglomerate sizes between 138–354 nm and a particle mass fraction of 10 wt%.

Effects of Al(OH)O nanoparticle agglomerate size in epoxy resin on tension, bending, and fracture properties

International Nuclear Information System (INIS)

Jux, Maximilian; Finke, Benedikt; Mahrholz, Thorsten; Sinapius, Michael; Kwade, Arno; Schilde, Carsten

2017-01-01

Several epoxy Al(OH)O (boehmite) dispersions in an epoxy resin are produced in a kneader to study the mechanistic correlation between the nanoparticle size and mechanical properties of the prepared nanocomposites. The agglomerate size is set by a targeted variation in solid content and temperature during dispersion, resulting in a different level of stress intensity and thus a different final agglomerate size during the process. The suspension viscosity was used for the estimation of stress energy in laminar shear flow. Agglomerate size measurements are executed via dynamic light scattering to ensure the quality of the produced dispersions. Furthermore, various nanocomposite samples are prepared for three-point bending, tension, and fracture toughness tests. The screening of the size effect is executed with at least seven samples per agglomerate size and test method. The variation of solid content is found to be a reliable method to adjust the agglomerate size between 138–354 nm during dispersion. The size effect on the Young’s modulus and the critical stress intensity is only marginal. Nevertheless, there is a statistically relevant trend showing a linear increase with a decrease in agglomerate size. In contrast, the size effect is more dominant to the sample’s strain and stress at failure. Unlike microscaled agglomerates or particles, which lead to embrittlement of the composite material, nanoscaled agglomerates or particles cause the composite elongation to be nearly of the same level as the base material. The observed effect is valid for agglomerate sizes between 138–354 nm and a particle mass fraction of 10 wt%.

Hyperfine excitation of OH+ by H

Science.gov (United States)

Lique, François; Bulut, Niyazi; Roncero, Octavio

2016-10-01

The OH+ ions are widespread in the interstellar medium and play an important role in the interstellar chemistry as they act as precursors to the H2O molecule. Accurate determination of their abundance rely on their collisional rate coefficients with atomic hydrogen and electrons. In this paper, we derive OH+-H fine and hyperfine-resolved rate coefficients by extrapolating recent quantum wave packet calculations for the OH+ + H collisions, including inelastic and exchange processes. The extrapolation method used is based on the infinite order sudden approach. State-to-state rate coefficients between the first 22 fine levels and 43 hyperfine levels of OH+ were obtained for temperatures ranging from 10 to 1000 K. Fine structure-resolved rate coefficients present a strong propensity rule in favour of Δj = ΔN transitions. The Δj = ΔF propensity rule is observed for the hyperfine transitions. The new rate coefficients will help significantly in the interpretation of OH+ spectra from photon-dominated region (PDR), and enable the OH+ molecule to become a powerful astrophysical tool for studying the oxygen chemistry.

Topologically identical, but geometrically isomeric layers in hydrous α-, β-Rb[UO2(AsO3OH)(AsO2(OH)2)]·H2O and anhydrous Rb[UO2(AsO3OH)(AsO2(OH)2)

International Nuclear Information System (INIS)

Yu, Na; Klepov, Vladislav V.; Villa, Eric M.; Bosbach, Dirk; Suleimanov, Evgeny V.; Depmeier, Wulf; Albrecht-Schmitt, Thomas E.; Alekseev, Evgeny V.

2014-01-01

The hydrothermal reaction of uranyl nitrate with rubidium nitrate and arsenic (III) oxide results in the formation of polymorphic α- and β-Rb[UO 2 (AsO 3 OH)(AsO 2 (OH) 2 )]·H 2 O (α-, β-RbUAs) and the anhydrous phase Rb[UO 2 (AsO 3 OH)(AsO 2 (OH) 2 )] (RbUAs). These phases were structurally, chemically and spectroscopically characterized. The structures of all three compounds are based upon topologically identical, but geometrically isomeric layers. The layers are linked with each other by means of the Rb cations and hydrogen bonding. Dehydration experiments demonstrate that water deintercalation from hydrous α- and β-RbUAs yields anhydrous RbUAs via topotactic reactions. - Graphical abstract: Three different layer geometries observed in the structures of Rb[UO 2 (AsO 3 OH)(AsO 2 (OH) 2 )] and α- and β- Rb[UO 2 (AsO 3 OH)(AsO 2 (OH) 2 )]·H 2 O. Two different coordination environments of uranium polyhedra (types I and II) are shown schematically on the top of the figure. - Highlights: • Three new uranyl arsenates were synthesized from the hydrothermal reactions. • The phases consist of the topologically identical but geometrically different layers. • Topotactic transitions were observed in the processes of mono-hyrates dehydration

Mechanism and kinetic properties for the OH-initiated atmospheric oxidation degradation of 9,10-Dichlorophenanthrene

Energy Technology Data Exchange (ETDEWEB)

Dang, Juan; Shi, Xiangli; Zhang, Qingzhu, E-mail: zqz@sdu.edu.cn; Hu, Jingtian; Wang, Wenxing

2015-02-01

Chlorinated polycyclic aromatic hydrocarbons (ClPAHs) have become a serious environmental concern due to their widespread occurrence and dioxin-like toxicities. In this work, the mechanism of the OH-initiated atmospheric oxidation degradation of 9,10-dichlorophenanthrene (9,10-Cl{sub 2}Phe) was investigated by using high-accuracy quantum chemistry calculations. The rate constants of the crucial elementary reactions were determined by the Rice–Ramsperger–Kassel–Marcus (RRKM) theory. The theoretical results were compared with the available experimental data. The main oxidation products are a group of ring-retaining and ring-opening compounds including chlorophenanthrols, 9,10-dichlorophenanthrene-3,4-dione, dialdehydes, chlorophenanthrenequinones, nitro-9,10-Cl{sub 2}Phe and epoxides et al. The overall rate constant of the OH addition reaction is 2.35 × 10{sup −12} cm{sup 3} molecule{sup −1} s{sup −1} at 298 K and 1 atm. The atmospheric lifetime of 9,10-Cl{sub 2}Phe determined by OH radicals is about 5.05 days. This study provides a comprehensive investigation of the OH-initiated oxidation degradation of 9,10-Cl{sub 2}Phe and should contribute to clarifying its atmospheric fate. - Highlights: • We studied a comprehensive mechanism of OH-initiated degradation of 9,10-Cl{sub 2}Phe. • The atmospheric lifetime of 9,10-Cl{sub 2}Phe determined by OH radical is about 5.05 d. • The rate constants of the crucial elementary steps were evaluated. • Water plays an important role in the formation of nitro-9,10-Cl{sub 2}Phe.

Comparison of rotational temperature derived from ground-based OH airglow observations with TIMED/SABER to evaluate the Einstein Coefficients

Science.gov (United States)

Liu, W.; Xu, J.; Smith, A. K.; Yuan, W.

2017-12-01

Ground-based observations of the OH(9-4, 8-3, 6-2, 5-1, 3-0) band airglows over Xinglong, China (40°24'N, 117°35'E) from December 2011 to 2014 are used to calculate rotational temperatures. The temperatures are calculated using five commonly used Einstein coefficient datasets. The kinetic temperature from TIMED/SABER is completely independent of the OH rotational temperature. SABER temperatures are weighted vertically by weighting functions calculated for each emitting vibrational state from two SABER OH volume emission rate profiles. By comparing the ground-based OH rotational temperature with SABER's, five Einstein coefficient datasets are evaluated. The results show that temporal variations of the rotational temperatures are well correlated with SABER's; the linear correlation coefficients are higher than 0.72, but the slopes of the fit between the SABER and rotational temperatures are not equal to 1. The rotational temperatures calculated using each set of Einstein coefficients produce a different bias with respect to SABER; these are evaluated over each of vibrational levels to assess the best match. It is concluded that rotational temperatures determined using any of the available Einstein coefficient datasets have systematic errors. However, of the five sets of coefficients, the rotational temperature derived with the Langhoff et al.'s (1986) set is most consistent with SABER. In order to get a set of optimal Einstein coefficients for rotational temperature derivation, we derive the relative values from ground-based OH spectra and SABER temperatures statistically using three year data. The use of a standard set of Einstein coefficients will be beneficial for comparing rotational temperatures observed at different sites.

OH/IR stars in the Galaxy

International Nuclear Information System (INIS)

Baud, B.

1978-01-01

Radio astronomical observations leading to the discovery of 71 OH/IR sources are described in this thesis. These OH/IR sources are characterized by their double peaked OH emission profile at a wavelength of 18 cm and by their strong IR infrared emission. An analysis of the distribution and radial velocities of a number of previously known and new OH/IR sources was performed. The parameter ΔV (the velocity separation between two emission peaks of the 18 cm line profile) was found to be a good criterion for a population classification with respect to stellar age

Oral Conditioned Cues Can Enhance or Inhibit Ethanol (EtOH)-Seeking and EtOH-Relapse Drinking by Alcohol-Preferring (P) Rats.

Science.gov (United States)

Knight, Christopher P; Hauser, Sheketha R; Deehan, Gerald A; Toalston, Jamie E; McBride, William J; Rodd, Zachary A

2016-04-01

Conditioned cues can elicit drug-seeking in both humans and rodents. The majority of preclinical research has employed excitatory conditioned cues (stimuli present throughout the availability of a reinforcer), but oral consumption of alcohol is similar to a conditional stimuli (presence of stimuli is paired with the delivery of the reinforcer) approach. The current experiments attempted to determine the effects of conditional stimuli (both excitatory and inhibitory) on the expression of context-induced ethanol (EtOH)-seeking. Alcohol-preferring (P) rats self-administered EtOH and water in standard 2-lever operant chambers. A flavor was added to the EtOH solution (CS+) during the EtOH self-administration sessions. After 10 weeks, rats underwent extinction training (7 sessions), followed by a 2-week home cage period. Another flavor was present during extinction (CS-). Rats were exposed to a third flavor in a non-drug-paired environment (CS(0)). EtOH-seeking was assessed in the presence of no cue, CS+, CS-, or CS(0) in the dipper previously associated with EtOH self-administration (no EtOH available). Rats were maintained a week in their home cage before being returned to the operant chambers with access to EtOH (flavored with no cue, CS+, CS-, or CS(0)). The results indicated that the presence of the CS+ enhanced EtOH-seeking, while the presence of the CS- suppressed EtOH-seeking. Similarly, adding the CS- flavor to 15% EtOH reduced responding for EtOH while the CS+ enhanced responding for EtOH during relapse testing. Overall, the data indicate that conditional stimuli are effective at altering both EtOH-seeking behavior and EtOH-relapse drinking. Copyright © 2016 by the Research Society on Alcoholism.

15 years of VLT/UVES OH intensities and temperatures in comparison with TIMED/SABER data

Science.gov (United States)

Noll, Stefan; Kimeswenger, Stefan; Proxauf, Bastian; Unterguggenberger, Stefanie; Kausch, Wolfgang; Jones, Amy M.

2017-10-01

The high-resolution echelle spectrograph UVES of the Very Large Telescope at Cerro Paranal in Chile has been regularly operated since April 2000. Thus, UVES archival data originally taken for astronomical projects but also including sky emission can be used to study airglow variations on a time scale longer than a solar cycle. Focusing on OH emission and observations until March 2015, we considered about 3000 high-quality spectra from two instrumental set-ups centred on 760 and 860 nm, which cover about 380 nm each. These data allowed us to measure line intensities for several OH bands in order to derive band intensities and rotational temperatures for different upper vibrational levels as a function of solar activity and observing date. The results were compared with those derived from emission and temperature profile data of the radiometer SABER on the TIMED satellite taken in the Cerro Paranal area between 2002 and 2015. In agreement with the SABER data, the long-term variations in OH intensity and temperature derived from the UVES data are dominated by the solar cycle, whereas secular trends appear to be negligible. Combining the UVES and SABER results, the solar cycle effects for the OH intensity and temperature are about 12-17% and 4-5 K per 100 sfu and do not significantly depend on the selected OH band. The data also reveal that variations of the effective OH emission layer height and air density can cause significant changes in the OH rotational temperatures due to a varying ratio of OH thermalising collisions by air molecules and OH radiation, deactivation, and destruction processes which impede the rotational relaxation. However, this effect appears to be of minor importance for the explanation of the rotational temperature variations related to the solar activity cycle, which causes only small changes in the OH emission profile.

Detailed characterization of a Comparative Reactivity Method (CRM) instrument for ambient OH reactivity measurements: experiments vs. modeling

Science.gov (United States)

Michoud, Vincent; Locoge, Nadine; Dusanter, Sébastien

2015-04-01

The Hydroxyl radical (OH) is the main daytime oxidant in the troposphere, leading to the oxidation of Volatile Organic Compounds (VOCs) and the formation of harmful pollutants such as ozone (O3) and Secondary Organic Aerosols (SOA). While OH plays a key role in tropospheric chemistry, recent studies have highlighted that there are still uncertainties associated with the OH budget, i.e the identification of sources and sinks and the quantification of production and loss rates of this radical. It has been demonstrated that ambient measurements of the total OH loss rate (also called total OH reactivity) can be used to identify and reduce these uncertainties. In this context, the Comparative Reactivity Method (CRM), developed by Sinha et al. (ACP, 2008), is a promising technique to measure total OH reactivity in ambient air and has already been used during several field campaigns. This technique relies on monitoring competitive reactions of OH with ambient trace gases and a reference compound (pyrrole) in a sampling reactor to derive ambient OH reactivity. However, this technique requires a complex data processing chain that has yet to be carefully investigated in the laboratory. In this study, we present a detailed characterization of a CRM instrument developed at Mines Douai, France. Experiments have been performed to investigate the dependence of the CRM response on humidity, ambient NOx levels, and the pyrrole-to-OH ratio inside the sampling reactor. Box modelling of the chemistry occurring in the reactor has also been performed to assess our theoretical understanding of the CRM measurement. This work shows that the CRM response is sensitive to both humidity and NOx, which can be accounted for during data processing using parameterizations depending on the pyrrole-to-OH ratio. The agreement observed between laboratory studies and model results suggests a good understanding of the chemistry occurring in the sampling reactor and gives confidence in the CRM

A density functional theory study of arsenic immobilization by the Al(III)-modified zeolite clinoptilolite

NARCIS (Netherlands)

Awuah, Joel B.; Dzade, N.Y.; Tia, Richard; Adei, Evans; Kwakye-Awuah, Bright; Catlow, C. Richard A.; de Leeuw, Nora H.

2016-01-01

We present density functional theory calculations of the adsorption of arsenic acid (AsO(OH)3) and arsenous acid (As(OH)3) on the Al(III)-modified natural zeolite clinoptilolite under anhydrous and hydrated conditions. From our calculated adsorption energies, we show that adsorption of both arsenic

Pharmacokinetics of 1,25(OH)(2)D(3) and 1alpha(OH)D(3) in normal and uraemic men

DEFF Research Database (Denmark)

Brandi, Lisbet; Egfjord, Martin; Olgaard, Klaus

2002-01-01

,25(OH)(2)D(3) (n=6) protocol. RESULTS: After oral administration of 1,25(OH)(2)D(3) the bioavailability of 1,25(OH)(2)D(3) was 70.6+/-5.8/72.2+/-4.8% in healthy volunteers/uraemic patients (n.s.). After i.v. administration the volume of distribution of 1,25(OH)(2)D(3) was similar, 0.49+/-0.14 vs 0...

Vibrational spectroscopy of the phosphate mineral lazulite--(Mg, Fe)Al2(PO4)2·(OH)2 found in the Minas Gerais, Brazil.

Science.gov (United States)

Frost, Ray L; Xi, Yunfei; Beganovic, Martina; Belotti, Fernanda Maria; Scholz, Ricardo

2013-04-15

This research was done on lazulite samples from the Gentil mine, a lithium bearing pegmatite located in the municipality of Mendes Pimentel, Minas Gerais, Brazil. Chemical analysis was carried out by electron microprobe analysis and indicated a magnesium rich phase with partial substitution of iron. Traces of Ca and Mn, (which partially replaced Mg) were found. The calculated chemical formula of the studied sample is: (Mg0.88, Fe0.11)Al1.87(PO4)2.08(OH)2.02. The Raman spectrum of lazulite is dominated by an intense sharp band at 1060 cm(-1) assigned to PO stretching vibrations of of tetrahedral [PO4] clusters presents into the HPO4(2-) units. Two Raman bands at 1102 and 1137 cm(-1) are attributed to both the HOP and PO antisymmetric stretching vibrations. The two infrared bands at 997 and 1007 cm(-1) are attributed to the ν1PO4(3-) symmetric stretching modes. The intense bands at 1035, 1054, 1081, 1118 and 1154 cm(-1) are assigned to the ν3PO4(3-) antisymmetric stretching modes from both the HOP and tetrahedral [PO4] clusters. A set of Raman bands at 605, 613, 633 and 648 cm(-1) are assigned to the ν4 out of plane bending modes of the PO4, HPO4 and H2PO4 units. Raman bands observed at 414, 425, 460, and 479 cm(-1) are attributed to the ν2 tetrahedral PO4 clusters, HPO4 and H2PO4 bending modes. The intense Raman band at 3402 and the infrared band at 3403 cm(-1) are assigned to the stretching vibration of the OH units. A combination of Raman and infrared spectroscopy enabled aspects of the molecular structure of the mineral lazulite to be understood. Copyright © 2013 Elsevier B.V. All rights reserved.

Evaluation of Lime and Persulfate Treatment for Mixed Contaminant Soil from Plum Brook Ordnance Works (Sandusky, OH)

Science.gov (United States)

2007-09-01

OH) Victor F. Medina, Scott A. Waisner, Agnes B. Morrow, Catherine C. Nestler, and Michael Jones September 2007 E nv ir on m en ta l L ab or... hydroxyapatite , and calcium, sodium, potassium, and ammonium phosphates Tardy et al. (2003). Several recent studies have also reported that phosphate

Redetermination of Ce[B5O8(OH(H2O]NO3·2H2O

Directory of Open Access Journals (Sweden)

Ya-Xi Huang

2012-05-01

Full Text Available The crystal structure of Ce[B5O8(OH(H2O]NO3·2H2O, cerium(III aquahydroxidooctaoxidopentaborate nitrate dihydrate, has been redetermined from single-crystal X-ray diffraction data. In contrast to the previous determination [Li et al. (2003. Chem. Mater. 15, 2253–2260], the present study reveals the location of all H atoms, slightly different fundamental building blocks (FBBs of the polyborate anions, more reasonable displacement ellipsoids for all non-H atoms, as well as a model without disorder of the nitrate anion. The crystal structure is built from corrugated polyborate layers parallel to (010. These layers, consisting of [B5O8(OH(H2O]2− anions as FBBs, stack along [010] and are linked by Ce3+ ions, which exhibit a distorted CeO10 coordination sphere. The layers are additionally stabilized via O—H...O hydrogen bonds between water molecules and nitrate anions, located at the interlayer space. The [BO3(H2O]-group shows a [3 + 1] coordination and is considerably distorted from a tetrahedral configuration. Bond-valence-sum calculation shows that the valence sum of boron is only 2.63 valence units (v.u. when the contribution of the water molecule (0.49 v.u. is neglected.

Mg/Al Ordering in Layered Double Hydroxides Revealed by Multinuclear NMR Spectroscopy

DEFF Research Database (Denmark)

Nielsen, Ulla Gro; Grey, Clare P.; Sideris, Paul J.

2008-01-01

The anion- exchange ability of layered double hydroxides ( LDHs) has been exploited to create materials for use in catalysis, drug delivery, and environmental remediation. The specific cation arrangements in the hydroxide layers of hydrotalcite- like LDHs, of general formula Mg1-x2+Alx3+OH2(Anion...

OH megamasers: dense gas & the infrared radiation field

Science.gov (United States)

Huang, Yong; Zhang, JiangShui; Liu, Wei; Xu, Jie

2018-06-01

To investigate possible factors related to OH megamaser formation (OH MM, L_{H2O}>10L_{⊙}), we compiled a large HCN sample from all well-sampled HCN measurements so far in local galaxies and identified with the OH MM, OH kilomasers (L_{H2O}gas and the dense gas, respectively), we found that OH MM galaxies tend to have stronger HCN emission and no obvious difference on CO luminosity exists between OH MM and non-OH MM. This implies that OH MM formation should be related to the dense molecular gas, instead of the low-density molecular gas. It can be also supported by other facts: (1) OH MMs are confirmed to have higher mean molecular gas density and higher dense gas fraction (L_{HCN}/L_{CO}) than non-OH MMs. (2) After taking the distance effect into account, the apparent maser luminosity is still correlated with the HCN luminosity, while no significant correlation can be found at all between the maser luminosity and the CO luminosity. (3) The OH kMs tend to have lower values than those of OH MMs, including the dense gas luminosity and the dense gas fraction. (4) From analysis of known data of another dense gas tracer HCO^+, similar results can also be obtained. However, from our analysis, the infrared radiation field can not be ruled out for the OH MM trigger, which was proposed by previous works on one small sample (Darling in ApJ 669:L9, 2007). On the contrary, the infrared radiation field should play one more important role. The dense gas (good tracers of the star formation) and its surrounding dust are heated by the ultra-violet (UV) radiation generated by the star formation and the heating of the high-density gas raises the emission of the molecules. The infrared radiation field produced by the re-radiation of the heated dust in turn serves for the pumping of the OH MM.

A preliminary report on the effects of long-term exposure of LiOH on pure nickel

Science.gov (United States)

Whittenberger, J. D.

1987-01-01

A 'bread pan' capsule has been designed which allows large numbers of tensile specimens to be simultaneously exposed to molten LiOH, its vapor, and vacuum. Capsules and specimens fabricated from the pure nickel alloy Ni-200 were annealed for 401 hours and 2500 hours at 775 K. Examination of the exposed materials revealed that little outward damage in terms of visible attack, weight change, or loss of room temperature tensile properties occurred. In particular, the mechanical behavior of hydroxide-contaminated alloy was essentially identical to that receiving a simple thermal exposure in vacuum. Examination of the microstructures revealed that LiOH did produce some nonuniform, shallow intergranular corrosion in NI-200; however, the extent of the damage was insufficient to produce weakening or embrittlement.

A simulation study on the topotactic transformations from aluminophosphate AlPO(4)-21 to AlPO(4)-25.

Science.gov (United States)

Li, J; Yu, J; Wang, K; Zhu, G; Xu, R

2001-11-05

Aluminophosphate AlPO(4)-21 (AWO), formulated /(CH(3))(2)NH(2)/[Al(3)P(3)O(12)(OH)], has been synthesized solvothermally by using dimethylamine as the template. Single-crystal X-ray diffraction analysis shows that AlPO(4)-21 crystallizes in the monoclinic space group P2(1)/n with a = 8.687(2) A, b = 17.428(5) A, c = 9.159(2) A, beta = 109.60(2) degrees, V = 1306.3(5) A(3), and Z = 4. XRD analysis shows that AlPO(4)-21 transforms to AlPO(4)-25 (ATV) upon calcination at 500 degrees C. The molecular dynamics simulation approach was used to investigate the topotactic transformations from AlPO(4)-21. The simulation study suggests that AlPO(4)-21 is energetically favored to transform to AlPO(4)-25, as well as other hypothetical forms, by the changing of the UUDD chains to the UDUD chains.

The nature of OH/IR stars

International Nuclear Information System (INIS)

Herman, J.

1983-01-01

In this work masers in evolved stars are studied, in particular the emission from the OH radical. The time variability of the OH masers was measured over a period of five years with the Dwingeloo Radio Telescope. These single-dish observations proved that most of the underlying stars are very long period variables, apparently a kind of extension of the well-known long period Mira variables. The mean OH fluxes and epochs were obtained as well as a confirmation of the radiative coupling between the maser and the star (by comparison with infrared data provided by other observers), the degree of saturation, and, most important of all, a determination of the linear dimensions of the circumstellar shells. Multi-element interferometer observations were made in order to study the spatial structure of OH masers. By combining the phase lag measurements and the spatial extent distances to individual stars could be determined with a high, unprecedented accuracy. Infrared broad-band photometry was done in the wavelength region from 3 μm to 20 μm, where most of the energy of these objects is radiated. The space density and galactic distribution of OH/IR stars are discussed and compared with the appearance of OH masers in the solar neighbourhood. (Auth.)

Estudio por difracción de rayos X de la hidratación de mezclas de CaAl2O4 - Humo de silice

Directory of Open Access Journals (Sweden)

Rodríguez, M. A.

2007-12-01

Full Text Available The influence of the amorphous silica on the mechanism of hydration of the calcium monoaluminate (CaAl2O4 has been studied at ambient temperature with a water/solids ratio of 0.5. The evolution of the hydrated phases, formed in the first instants of the reaction, has been studied by laboratory X ray diffraction with a time resolution of 36 min. The integration of selected diffraction peaks of the phases: Ca2Al2O5•8H2O (Ca2Al2(OH10•3H2O, CaAl2O4 and Ca4Al2(OH12(CO3•5H2O, has allowed to establish the kinetics of the reaction. This way, it has been shown that the amorphous silica causes a drastic decrease in the period of induction of the hydration and accelerates the formation of the metastable crystalline hydrates Ca2Al2(OH10•3H2O and Ca4Al2(OH12(CO3•5H2O. These results have been confirmed by Thermogravimetry, Differential Thermal Analysis and Scanning Electric Microscopy. The hydration mechanism proposed confirms previous data of Nuclear Magnetic Resonance of Solids (RMN of 29Si of the authors of this paper.Se ha estudiado la influencia del humo de sílice sobre el mecanismo de hidratación del monoaluminato de calcio (CaAl2O4 a temperatura ambiente y con una relación agua/sólidos de 0,5. La evolución de las fases hidratadas, que se forman en los primeros instantes de la reacción, se ha estudiado por difracción de rayos X de laboratorio con una resolución temporal de 36 min. La integración de picos de difracción seleccionados de las fases: Ca2Al2O5•8H2O (Ca2Al2(OH10•3H2O, CaAl2O4 y Ca4Al2(OH12(CO3•5H2O, ha permitido establecer la cinética de la reacción. Así, se ha puesto de manifiesto que el humo de sílice provoca una drástica disminución en el periodo de inducción de la hidratación y acelera la formación de los hidratos cristalinos metaestables Ca2Al2(OH10•3H2O y Ca4Al2(OH12(CO3•5H2O. Estos resultados se han confirmado por Termogravimetría, Análisis Térmico Diferencial y Microscopía Electrónica de

Simple synthesis of Al{sub 2}O{sub 3} sphere composite from hybrid process with improved thermal stability for catalytic applications

Energy Technology Data Exchange (ETDEWEB)

Santos, Regina C.R., E-mail: reginaclaudiasantos@yahoo.com.br [Department of Analytical Chemistry and Physical Chemistry, Federal University of Ceará, Campus of Pici, Fortaleza, CE, CEP: 60440-554 (Brazil); Pinheiro, Antônio N.; Leite, Edson R. [Department of Chemistry, Federal University of São Carlos, São Carlos, SP, CEP: 13560-905 (Brazil); Freire, Valder N. [Department of Physics, Federal University of Ceará, Campus of Pici, Fortaleza, CE, CEP: 60440-554 (Brazil); Longhinotti, Elisane; Valentini, Antoninho [Department of Analytical Chemistry and Physical Chemistry, Federal University of Ceará, Campus of Pici, Fortaleza, CE, CEP: 60440-554 (Brazil)

2015-06-15

Aluminium oxide spheres were synthesized by the hybrid process applying the biopolymer chitosan. After the calcination process the porous spheres were characterized by Chemical elemental analysis (XRF), X-ray diffraction (XRD), Scanning electron microscopy and Energy Dispersive X-ray Spectroscopy (SEM-EDS), N{sub 2} adsorption–desorption isotherms, infrared spectroscopy (IR), and CO{sub 2} temperature programmed desorption (CO{sub 2}-TPD). The effect of thermal treatment on surface properties of the oxide spheres was also evaluated by the catalytic ethanol dehydration reaction. The hybrid method produced interesting results related to the thermal stability against sintering process and consequently low decreases of surface area. The hybrid spheres calcination at 900 and 1200 °C produced a metastable phases of alumina with a high surface area, and nanometric crystallites. Additionally, the spheres of mixed silica-alumina synthesized by this method reveal the formation of porous spheres with highly acidic OH groups, which was suggested by the catalytic performance. - Highlights: • Al and Si/Al oxide spheres with promising properties are synthesized by hybrid method. • Al{sub 2}O{sub 3} spheres show high thermal stability and resistance the loss surface area. • The SiO{sub 2} addition plays an important role in the structure and porosity of the spheres. • Al{sub 2}O{sub 3} and SiO{sub 2}/Al{sub 2}O{sub 3} spheres presented a good activity to conversion ethanol. • The activity is related to the surface area and density of OH groups on surface.

Intercomparison of OH and OH reactivity measurements in a high isoprene and low NO environment during the Southern Oxidant and Aerosol Study (SOAS)

Science.gov (United States)

Sanchez, Dianne; Jeong, Daun; Seco, Roger; Wrangham, Ian; Park, Jeong-Hoo; Brune, William H.; Koss, Abigail; Gilman, Jessica; de Gouw, Joost; Misztal, Pawel; Goldstein, Allen; Baumann, Karsten; Wennberg, Paul O.; Keutsch, Frank N.; Guenther, Alex; Kim, Saewung

2018-02-01

We intercompare OH and OH reactivity datasets from two different techniques, chemical ionization mass spectrometry (CIMS) and laser-induced fluorescence (LIF) in a high isoprene and low NO environment in a southeastern US forest during the Southern Oxidant and Aerosol Study (SOAS). An LIF instrument measured OH and OH reactivity at the top of a tower, a CIMS instrument measured OH at the top of the tower, and a CIMS based comparative reactivity method (CRM-CIMS) instrument deployed at the base of the tower measured OH reactivity. Averaged diel variations of OH and OH reactivity from these datasets agree within analytical uncertainty and correlations of LIF versus CIMS for OH and OH reactivity have slopes of 0.65 and 0.97, respectively. However, there are systematic differences between the measurement datasets. The CRM-CIMS measurements of OH reactivity were ∼16% lower than those by the LIF technique in the late afternoon. We speculate that it is caused by losses in the sampling line down to the CRM-CIMS instrument. On the other hand, we could not come up with a reasonable explanation for the difference in the LIF and CIMS OH datasets for early morning and late afternoon when OH is below 1 × 106 molecules cm-3. Nonetheless, results of this intercomparison exercise strengthen previous publications from the field site on OH concentrations and atmospheric reactivity.

Antidepressants differentially related to 1,25-(OH)₂ vitamin D₃ and 25-(OH) vitamin D₃ in late-life depression.

Science.gov (United States)

Oude Voshaar, R C; Derks, W J; Comijs, H C; Schoevers, R A; de Borst, M H; Marijnissen, R M

2014-04-15

A low plasma 25-OH vitamin D3 level is a universal risk factor for a wide range of diseases and has also been implicated in late-life depression. It is currently unknown whether the biologically active form of vitamin D, that is, 1,25-(OH)2 vitamin D3, is also decreased in late-life depression, or whether vitamin D levels correlate with specific depression characteristics. We determined plasma 25-OH vitamin D3, 1,25-(OH)2 vitamin D3 and parathormone levels in 355 depressed older persons and 124 non-depressed comparison subjects (age 60 years). Psychopathology was established with the Composite International Diagnostic Interview 2.1, together with potential confounders and depression characteristics (severity, symptom profile, age of onset, recurrence, chronicity and antidepressant drug use). Adjusted for confounders, depressed patients had significantly lower levels of 25-OH vitamin D33 (Cohen's d =0.28 (95% confidence interval: 0.07-0.49), P=0.033) as well as 1,25-(OH)2 vitamin D3 (Cohen's d =0.48 (95% confidence interval: 0.27-0.70), Pdepression characteristics tested, only the use of tricyclic antidepressants (TCAs) was significantly correlated with lower 1,25-(OH)2 vitamin D3 levels (Cohen's d =0.86 (95% confidence interval: 0.53-1.19), Pprecursor 25-OH vitamin D3. As vitamin D levels were significantly lower after adjustment for confounders, vitamin D might have an aetiological role in late-life depression. Differences between depressed and non-depressed subjects were largest for the biologically active form of vitamin D. The differential impact of TCAs on 25-OH vitamin D3 and 1,25-(OH)2 vitamin D3 levels suggests modulation of 1-α-hydroxylase and/or 24-hydroxylase, which may in turn have clinical implications for biological ageing mechanisms in late-life depression.

Facile in situ synthesis of hierarchical porous Ni/Ni(OH)₂ hybrid sponges with excellent electrochemical energy-storage performances for supercapacitors.

Science.gov (United States)

Wang, Wanren; Wang, Wenhua; Wang, Mengjiao; Guo, Xiaohui

2014-09-01

Herein, we report the in situ growth of single-crystalline Ni(OH)2 nanoflakes on a Ni support by using facile hydrothermal processes. The as-prepared Ni/Ni(OH)2 sponges were well-characterized by using X-ray diffraction (XRD), SEM, TEM, and X-ray photoelectron spectroscopy (XPS) techniques. The results revealed that the nickel-skeleton-supported Ni(OH)2 rope-like aggregates were composed of numerous intercrossed single-crystal Ni(OH)2 flake-like units. The Ni/Ni(OH)2 hybrid sponges served as electrodes and displayed ultrahigh specific capacitance (SC=3247 F g(-1)) and excellent rate-capability performance, likely owing to fast electron and ion transport, sufficient Faradic redox reaction, and robust structural integrity of the Ni/Ni(OH)2 hybrid electrode. These results support the promising application of Ni(OH)2 nanoflakes as advanced pseudocapacitor materials. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Surface charges and Np(V) sorption on amorphous Al- and Fe- silicates

International Nuclear Information System (INIS)

Del Nero, M.; Assada, A.; Barillon, R.; Duplatre, G.; Made, B.

2005-01-01

Full text of publication follows: Sorption onto Si-rich alteration layers of crystalline minerals and nuclear glasses, and onto amorphous secondary silicates of rocks and soils, are expected to retard the migration of actinides in the near- and far-field of HLW repositories. We present experimental and modeling studies on the effects of silicate structure and bulk chemistry, and of solution chemistry, on charges and adsorption of neptunyl ions at surfaces of synthetic, amorphous or poorly ordered silica, Al-silicates and Fe-silicates. The Al-silicates display similar pH-dependent surface charges characterized by predominant Si-O - Si sites, and similar surface affinities for neptunyl ions, irrespective to their Si/Al molar ratio (varying from 10 to 4.3). Such experimental features are explained by incorporation of Al atoms in tetrahedral position in the silicate lattice, leading to only trace amounts of high-affinity Al-OH surface groups due to octahedral Al. By contrast, the structure of the Fe-silicates ensures the occurrence of high-affinity Fe-OH surface groups, whose concentration is shown by proton adsorption measurements to increase with decreasing of the silicate Si/Fe molar ratio (from 10 to 2.3). Nevertheless, experimental data of the adsorption of neptunyl and electrolyte ions show unexpectedly weak effect of the Si/Fe ratio, and suggest predominant Si-OH surface groups. A possible explanation is that aqueous silicate anions, released by dissolution, adsorb at OH Fe - surface groups and / or precipitate as silica gel coatings, because experimental solutions were found at near-equilibrium with respect to amorphous silica. Therefore, the environmental sorption of Np(V) onto Si-rich, amorphous or poorly ordered Al-silicates may primarily depend on pH and silicate specific surface areas, given the low overall chemical affinity of such phases for dissolved metals. By contrast, the sorption of Np(V) on natural, amorphous or poorly ordered Fe-silicates may be a

Time-Dependent Quantum Wave Packet Study of the Si + OH → SiO + H Reaction: Cross Sections and Rate Constants.

Science.gov (United States)

Rivero Santamaría, Alejandro; Dayou, Fabrice; Rubayo-Soneira, Jesus; Monnerville, Maurice

2017-03-02

The dynamics of the Si( 3 P) + OH(X 2 Π) → SiO(X 1 Σ + ) + H( 2 S) reaction is investigated by means of the time-dependent wave packet (TDWP) approach using an ab initio potential energy surface recently developed by Dayou et al. ( J. Chem. Phys. 2013 , 139 , 204305 ) for the ground X 2 A' electronic state. Total reaction probabilities have been calculated for the first 15 rotational states j = 0-14 of OH(v=0,j) at a total angular momentum J = 0 up to a collision energy of 1 eV. Integral cross sections and state-selected rate constants for the temperature range 10-500 K were obtained within the J-shifting approximation. The reaction probabilities display highly oscillatory structures indicating the contribution of long-lived quasibound states supported by the deep SiOH/HSiO wells. The cross sections behave with collision energies as expected for a barrierless reaction and are slightly sensitive to the initial rotational excitation of OH. The thermal rate constants show a marked temperature dependence below 200 K with a maximum value around 15 K. The TDWP results globally agree with the results of earlier quasi-classical trajectory (QCT) calculations carried out by Rivero-Santamaria et al. ( Chem. Phys. Lett. 2014 , 610-611 , 335 - 340 ) with the same potential energy surface. In particular, the thermal rate constants display a similar temperature dependence, with TDWP values smaller than the QCT ones over the whole temperature range.

Mechanochemical synthesis of dodecyl sulfate anion (DS-) intercalated Cu-Al layered double hydroxide

Science.gov (United States)

Qu, Jun; He, Xiaoman; Lei, Zhiwu; Zhang, Qiwu; Liu, Xinzhong

2017-12-01

Dodecyl sulfate anion (DS-) was successfully intercalated into the gallery space of Cu-Al layered double hydroxides (LDH) by a non-heating mechanochemical route, in which basic cupric carbonate (Cu2(OH)2CO3) and aluminum hydroxide (Al(OH)3) were first dry ground and then agitated in SDS solution under ambient environment. The organics modified Cu-Al LDH showed good adsorption ability toward 2,4-dichlorophenoxyacetic acid (2, 4-D). The prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), CHS elemental analysis and Scanning electron microscopy (SEM). The LDH precursor prepared by ball-milling could directly react with SDS molecules forming a pure phase of DS- pillared Cu-Al LDH, which was not observed with the LDH product through the ion-exchange of DS- at room temperature. The process introduced here may be applied to manufacture other types of organic modified composites for pollutants removal and other applications.

OH radiation from the interstellar cloud medium

Energy Technology Data Exchange (ETDEWEB)

Nguyen-Q-Rieu,; Winnberg, A [Max-Planck-Institut fuer Radioastronomie, Bonn (F.R. Germany); Guibert, J [Observatoire de Paris, Section de Meudon, 92 (France); Lepine, J R.D. [Universidade Mackenzie, Sao Paulo (Brazil). Centro de Radio-Astronomia et Astrofisica; Johansson, L E.B. [Rymdobservatoriet, Onsala (Sweden); Goss, W M [Commonwealth Scientific and Industrial Research Organization, Epping (Australia). Div. of Radiophysics

1976-02-01

We have detected OH in the direction of about 50% of the continuum sources investigated. The OH abundance is one order of magnitude less than usually found in dust clouds. Most of the OH features have HI counterparts. This suggests that the OH radiation arises from the HI interstellar cold clouds. Our observations allowed in some cases the determination of the excitation temperatures in all four lines. A pumping model involving far-infrared radiation and collisions with neutral and charged particles has been proposed. It explains the observed excitation temperatures.

1 IN TR ODU CT ION Gibbsite (7-Al(OH)3) and boehmite (7-AlOOH ...

African Journals Online (AJOL)

2005-07-10

Jul 10, 2005 ... of A-B-B-A-A-B-B-A-A-B in the direction perpen- dicular to the planes. On dehydroxylation, boehmite and gibbsite do not go directly to the thermodynamically stable a-. Al2O3 phase. Initially the long range crystalline order is destroyed to give 'transition aluminas' or. 'activated aluminas' (Misra, 1 986, Ingram ...

Comparison of H/Al stoichiometry of mineral and organic soils in Brazil Comparação da estequiometria H/Al em solos minerais e orgânicos brasileiros

Directory of Open Access Journals (Sweden)

Daniel Vidal Perez

2009-08-01

Full Text Available Exchangeable Al has been used as a criterion for the calculation of lime requirement in several Brazilian States. However, the laboratory method with extraction by a 1 mol L-1 KCl solution followed by indirect alkaline titration is not accurate for some Brazilian soils, mainly in the case of soils with high organic matter content. The objective of this study was therefore to evaluate the stoichiometry of H+/Al3+ in KCl soil extracts. The results suggested that organically complexed Al is the main contributor to exchangeable acidity in soils enriched with organic matter. Liming recommendations for organic soils based exclusively on exchangeable Al determined by the NaOH titration method should therefore be revised.A determinação de alumínio trocável é utilizada como critério para cálculo de calagem em vários estados brasileiros. Contudo, a determinação indireta pela titulação com NaOH, após extração com solução de KCl 1 mol L-1, pode não ser adequada para certos tipos de solos brasileiros, notadamente aqueles que apresentem altos teores de carbono orgânico. Dessa forma, o principal objetivo deste trabalho foi avaliar a estequiometria da relação H+/Al3+ em extratos de KCl. Os resultados obtidos sugerem que o Al complexado pela matéria orgânica, em solos orgânicos, é o principal contribuinte para a acidez trocável obtida por titulação. Dessa forma, a recomendação de calagem em solos orgânicos baseado somente na determinação de alumínio trocável por titulação com NaOH deve ser revista.

Retention of chromium by modified Al-Bentonite Retenção de cromo por Al-bentonita modificada

Directory of Open Access Journals (Sweden)

C. Volzone

2002-09-01

Full Text Available Retention of chromium (III from a tanning wastewater by modified Al-bentonites was studied. One bentonite from San Juan province, Argentina, was used. Al-bentonite was prepared by contact of bentonite with hydrolyzed OH-Al solutions (0.10 M in Al for 24 hours. The modified Al-bentonites were obtained by: a treatment with 0.5 M sodium chloride; b with 0.5 M sodium chloride adjusted at pH 8; and c treatment with an hexametaphosphate solution after sodium addition. Then, the samples were dried at 100 °C and heated at 500 °C. The chromium (III retention by samples was carried out in batch system putting in contact the material with a 2000 ppm Cr tannery waste at different times. The retained chromium was characterized by analyzing the supernatant using UV-visible spectroscopy. The different chromium retention was correlated with structural characteristics of the solids.Foi estudada a retenção de cromo (III de águas residuais por meio de Al-bentonitas modificadas. Foi usada uma bentonita da província de San Juan, Argentina. As bentonitas-Al forma preparadas colocando-as em contato com soluções (0,10 M Al hydrolizadas de OH-Al durante 24 horas. As bentonitas-Al modidicadas foram obtidas por meio de: a tratamento com cloreto de sódio 0,5 M; b com cloreto de sódio 0,5 M sodium com pH ajustado para 8; e c tratamento com uma solução de hexametafosfato após a adição de sódio. As amostras foram então secas a 100 °C e aquecidas a 500 °C. A retenção do cromo (III pelas amostras foi feita em lotes colocando o material em contato em diferentes tempos com um resíduo contendo 2000 ppm de cromo. O cromo retido foi caracterizado por meio de análise do sobrenadante usando espectroscopia UV-visível. As diferentes retenções de cromo foram correlacionadas com características estruturais dos sólidos.

Performance evaluation of symmetric supercapacitor based on cobalt hydroxide [Co(OH)2] thin film electrodes

International Nuclear Information System (INIS)

Jagadale, A.D.; Kumbhar, V.S.; Dhawale, D.S.; Lokhande, C.D.

2013-01-01

In the present investigation, we have successfully assembled symmetric supercapacitor device based on cobalt hydroxide [Co(OH) 2 ] thin film electrodes using 1 M KOH as an electrolyte. Initially, potentiodynamic electrodeposition method is employed for the preparation of Co(OH) 2 thin films onto stainless steel substrate. These films are characterized for structural and morphological elucidations using X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The XRD reveals formation of β-Co(OH) 2 material with hexagonal crystal structure. The SEM images show formation of nanoflakes like microstructure with average flake width 100 nm. Electrochemical characterizations of Co(OH) 2 based symmetric supercapacitor cell are carried out using cyclic voltammetry, charge–discharge and electrochemical impedance spectroscopy (EIS) techniques. In the performance evaluation the maximum values of specific capacitance, specific energy and specific power are encountered as 44 F g −1 , 3.96 Wh kg −1 and 42 kW kg −1 . The value of equivalent series resistance (ESR) is estimated as 2.3 Ω using EIS

Topologically identical, but geometrically isomeric layers in hydrous α-, β-Rb[UO2(AsO3OH)(AsO2(OH)2)]·H2O and anhydrous Rb[UO2(AsO3OH)(AsO2(OH)2)

Science.gov (United States)

Yu, Na; Klepov, Vladislav V.; Villa, Eric M.; Bosbach, Dirk; Suleimanov, Evgeny V.; Depmeier, Wulf; Albrecht-Schmitt, Thomas E.; Alekseev, Evgeny V.

2014-07-01

The hydrothermal reaction of uranyl nitrate with rubidium nitrate and arsenic (III) oxide results in the formation of polymorphic α- and β-Rb[UO2(AsO3OH)(AsO2(OH)2)]·H2O (α-, β-RbUAs) and the anhydrous phase Rb[UO2(AsO3OH)(AsO2(OH)2)] (RbUAs). These phases were structurally, chemically and spectroscopically characterized. The structures of all three compounds are based upon topologically identical, but geometrically isomeric layers. The layers are linked with each other by means of the Rb cations and hydrogen bonding. Dehydration experiments demonstrate that water deintercalation from hydrous α- and β-RbUAs yields anhydrous RbUAs via topotactic reactions.

Influence of the precursors in the chemical preparation of {gamma} - Al{sub 2}O{sub 3} in reactions of alcohols dehydration; Influencia de los precursores en la preparacion quimica de {gamma} - Al{sub 2}O{sub 3} en reacciones de deshidratacion de alcoholes

Energy Technology Data Exchange (ETDEWEB)

Salmones, J.; Limon, M.T.; Mayagoitia, V.; Rojas, F.; Kornhauser, I.; Morales, J.; Acosta, D. [Instituto Mexicano del Petroleo, Subdireccion General de Investigacion Aplicada, Apartado Postal 14-805, 07730, Mexico D.F. (Mexico)

1998-12-31

A chemical method for the synthesis of alumina substrates based on a microscopic morphological control, is presented. The influence of the precursor alcohol used for the synthesis of Al(OR){sub 3} is studied too. This latter compound is the raw material to synthesize the alumina materials treated here. The effects of alcohols such as ethanol, isopropanol and ter butanol are analyzed. Results show that an early formation (i.e. at low temperature) of the porous structure is reached in the case of {gamma} -Al{sub 2}O{sub 3} synthesized from ethanol. On the other hand, pore formation for alumina obtained from isopropanol and ter butanol, occurs until appearance of the {gamma} phase (at approximately 500 Centigrade). The different alumina substrates were used as catalysts in dehydration reactions of primary, secondary and tertiary alcohols. Decreasing catalytic activity corresponds to the sequence: (R-OH){sub 3} < (R-OH){sub 2} < (R-OH) in the case of ethanol; while for isopropanol and ter butanol the sequence is: (R-OH) < (R-OH){sub 2} < (R-OH){sub 3}. These results are explained by means of a reaction mechanism which is associated with the textural properties of the catalysts. (Author)

Photofragment imaging study of the CH2CCH2OH radical intermediate of the OH+allene reaction

International Nuclear Information System (INIS)

Raman, Arjun S.; Justine Bell, M.; Lau, K.-C.; Butler, Laurie J.

2007-01-01

These velocity map imaging experiments characterize the photolytic generation of one of the two radical intermediates formed when OH reacts via an addition mechanism with allene. The CH 2 CCH 2 OH radical intermediate is generated photolytically from the photodissociation of 2-chloro-2-propen-1-ol at 193 nm. Detecting the Cl atoms using [2+1] resonance-enhanced multiphoton ionization evidences an isotropic angular distribution for the Cl+CH 2 CCH 2 OH photofragments, a spin-orbit branching ratio for Cl( 2 P 1/2 ):Cl( 2 P 3/2 ) of 0.28, and a bimodal recoil kinetic energy distribution. Conservation of momentum and energy allows us to determine from this data the internal energy distribution of the nascent CH 2 CCH 2 OH radical cofragment. To assess the possible subsequent decomposition pathways of this highly vibrationally excited radical intermediate, we include electronic structure calculations at the G3//B3LYP level of theory. They predict the isomerization and dissociation transition states en route from the initial CH 2 CCH 2 OH radical intermediate to the three most important product channels for the OH+allene reaction expected from this radical intermediate: formaldehyde+C 2 H 3 , H+acrolein, and ethene+CHO. We also calculate the intermediates and transition states en route from the other radical adduct, formed by addition of the OH to the center carbon of allene, to the ketene+CH 3 product channel. We compare our results to a previous theoretical study of the O+allyl reaction conducted at the CBS-QB3 level of theory, as the two reactions include several common intermediates

Photofragment imaging study of the CH2CCH2OH radical intermediate of the OH +allene reaction

Science.gov (United States)

Raman, Arjun S.; Justine Bell, M.; Lau, Kai-Chung; Butler, Laurie J.

2007-10-01

These velocity map imaging experiments characterize the photolytic generation of one of the two radical intermediates formed when OH reacts via an addition mechanism with allene. The CH2CCH2OH radical intermediate is generated photolytically from the photodissociation of 2-chloro-2-propen-1-ol at 193nm. Detecting the Cl atoms using [2+1] resonance-enhanced multiphoton ionization evidences an isotropic angular distribution for the Cl +CH2CCH2OH photofragments, a spin-orbit branching ratio for Cl(P1/22):Cl(P3/22) of 0.28, and a bimodal recoil kinetic energy distribution. Conservation of momentum and energy allows us to determine from this data the internal energy distribution of the nascent CH2CCH2OH radical cofragment. To assess the possible subsequent decomposition pathways of this highly vibrationally excited radical intermediate, we include electronic structure calculations at the G3//B3LYP level of theory. They predict the isomerization and dissociation transition states en route from the initial CH2CCH2OH radical intermediate to the three most important product channels for the OH +allene reaction expected from this radical intermediate: formaldehyde+C2H3, H +acrolein, and ethene+CHO. We also calculate the intermediates and transition states en route from the other radical adduct, formed by addition of the OH to the center carbon of allene, to the ketene+CH3 product channel. We compare our results to a previous theoretical study of the O +allyl reaction conducted at the CBS-QB3 level of theory, as the two reactions include several common intermediates.

The structure of mixed H2O-OH monolayer films on Ru(0001)

Energy Technology Data Exchange (ETDEWEB)

Tatarkhanov, M.; Fomin, E.; Salmeron, M.; Andersson, K.; Ogasawara, H.; Pettersson, L.G.M.; Nilsson, A.; Cerda, J.I.

2008-10-20

Scanning tunneling microscopy (STM) and x-ray absorption spectroscopy (XAS) have been used to study the structures produced by water on Ru(0001) at temperatures above 140 K. It was found that while undissociated water layers are metastable below 140 K, heating above this temperature produces drastic transformations whereby a fraction of the water molecules partially dissociate and form mixed H{sub 2}O-OH structures. XPS and XAS revealed the presence of hydroxyl groups with their O-H bond essentially parallel to the surface. STM images show that the mixed H{sub 2}O-OH structures consist of long narrow stripes aligned with the three crystallographic directions perpendicular to the close-packed atomic rows of the Ru(0001) substrate. The internal structure of the stripes is a honeycomb network of H-bonded water and hydroxyl species. We found that the metastable low temperature molecular phase can also be converted to a mixed H{sub 2}O-OH phase through excitation by the tunneling electrons when their energy is 0.5 eV or higher above the Fermi level. Structural models based on the STM images were used for Density Functional Theory optimizations of the stripe geometry. The optimized geometry was then utilized to calculate STM images for comparison with the experiment.

Methanol oxidation in a flow reactor: Implications for the branching ratio of the CH3OH+OH reaction

DEFF Research Database (Denmark)

Rasmussen, Christian Lund; Wassard, K.H.; Dam-Johansen, Kim

2008-01-01

The oxidation of methanol in a flow reactor has been studied experimentally under diluted, fuel-lean conditions at 650-1350 K, over a wide range of O-2 concentrations (1%-16%), and with and without the presence of nitric oxide. The reaction is initiated above 900 K, with the oxidation rate...... decreasing slightly with the increasing O-2 concentration. Addition of NO results in a mutually promoted oxidation of CH3OH and NO in the 750-1100 K range. The experimental results are interpreted in terms of a revised chemical kinetic model. Owing to the high sensitivity of the mutual sensitization of CH3OH...... and NO oxidation to the partitioning of CH3O and CH2OH, the CH3OH + OH branching fraction could be estimated as alpha = 0.10 +/- 0.05 at 990 K. Combined with low-temperature measurements, this value implies a branching fraction that is largely independent of temperature. It is in good agreement with recent...

Measurements of total OH reactivity during PROPHET-AMOS 2016

Science.gov (United States)

Rickly, P.; Sakowski, J.; Bottorff, B.; Lew, M.; Stevens, P. S.; Sklaveniti, S.; Locoge, N.; Dusanter, S.

2017-12-01

As one of the main oxidant in the atmosphere, the hydroxyl radical (OH) initiates the oxidation of volatile organic compounds that can lead to the formation of ozone and secondary organic aerosols. Understanding both the sources and sinks of OH is therefore important to address issues related to air quality and climate change. Measurements of total OH reactivity can provide an important test of our understanding of the OH radical budget. Recent measurements of total reactivity in many environments have been greater than calculated based on the measured concentration of VOCs, suggesting that important OH sinks in these environments are not well characterized. Measurements of total OH reactivity were performed in a forested environment during the PROPHET - AMOS field campaign (Program for Research on Oxidants: PHotochemisty, Emissions, and Transport - Atmospheric Measurements of Oxidants in Summer) using the Comparative Reactivity Method (CRM) and the Total OH Loss Rate Method (TOHLM). The site is characterized by large emissions of isoprene and monoterpenes and low anthropogenic influence. Measurements of total OH reactivity using these two techniques agree to within their respective uncertainties, giving confidence in the measured OH reactivity. In addition, measurements of trace gases (VOCs, NOx, O3) were used to perform a comprehensive apportionment of OH sinks. These measurements are used in a chemical model using the Master Chemical Mechanism to calculate the expected OH reactivity. The results will be compared to previous measurements of total OH reactivity at this site.

Application of the Akinfiev-Diamond equation of state to neutral hydroxides of metalloids (B(OH)3, Si(OH)4, As(OH)3) at infinite dilution in water over a wide range of the state parameters, including steam conditions

Science.gov (United States)

Akinfiev, Nikolay N.; Plyasunov, Andrey V.

2014-02-01

treatment of data, see Table 1. The fitting procedure to evaluate the parameters of the Akinfiev-Diamond model also included the values of ΔfGo and S° of Si(OH)4 in ideal gas state at standard state conditions.First, to fit the EoS parameters, the dataset for g2∞ (Si(OH)4(aq)) has been generated using accepted experimental data on quartz solubility in water according to the reaction SiO2(quartz) + 2H2O = Si(OH)4(aq), as g2∞(SiOH(aq)(T,P)=g(quartz)(T,P)+2g(HO)(T,P)-RTlnm, where mSi corresponds to the molality of silica in the solution. Thermodynamic properties of quartz were adopted from SUPCRT database (Johnson et al., 1992), while g(H2O)(T, P) was computed using the Hill (1990) and/or Wagner and Pruß (2002) formulations.The fitting procedure was organized as described below. It is known that partial molar properties of dilute solutes close to the critical point of water are governed by the Krichevskii parameter, AKr (Levelt Sengers, 1991). Plyasunov (2012) recommended for Si(OH)4AKr = -190 ± 10 MPa evaluated from the available relevant data. We have used this value as an anchor while fitting. So, the fitting procedure was iterative. After any initial approximation for ξ, values of the a, b parameters of the EoS together with ΔfGo298(g) and So298(g) of Si(OH)4 were determined by a linear regression of the available g2∞ (Si(OH)4(aq)) experimental data. Then the ξ parameter was modified in compliance with the adopted AKr value (Eq. A7), and the fitting cycle was repeated until ξ ceased changing.The finally retrieved values for gaseous Si(OH)4 are ΔfGo298 = -1239.66 ± 1.7 kJ mol-1, So298 = 346.37 ± 3.5 J mol-1 K-1, and the EoS parameters are ξ = -1.8933; a = 0.9285 ± 1.1 cm3 g-1; b = -0.9409 ± 0.97 cm3 K0.5 g-1 (2σ confidence) (Table 1). Evaluated in this work values of ΔfGo298 and So298 for Si(OH)4 in the ideal gas state are very close to the data given in Plyasunov (2011b) on the basis of the analysis of the solubility amorphous silica and quartz in low

Equilibrium aluminium hydroxo-oxalate phases during initial clay formation; H +-Al 3+-oxalic acid-Na + system

Science.gov (United States)

Bilinski, Halka; Horvath, Laszlo; Ingri, Nils; Sjöberg, Staffan

1986-09-01

The conditions necessary for initial clay formation have been studied in different model systems comprising different organic acids besides Si and Al. In the present paper the solid phases and the precipitation boundary characterizing the subsystem H +-Al 3+-oxalic acid (H 2L) are discussed. pH and tyndallometric measurements were performed in an ionic medium of 0.6 M Na(Cl) at 25 °C. The two phases Al 3(OH) 7(C 2O 4) · 3H 2O (phase I) and NaAl(OH) 2(C 2O 4) · 3H 2O (phase II) determine the precipitation boundary. The following formation constants for the two phases were deduced: lgβ1 = lg([ Al3+] -3[ H2C2O4] -1[ H+] 9 = -21.87 ± 0.08 and lgβ11 = lg([ Al3+] -1[ H2C2O4] -1[ H+] 4 = -5.61 ± 0.06. Phase I exists in the range [ Al] tot≥ 10 -4.4moldm-3,[ H2C2O4] tot ≥ 10 -4.9moldm-3 and at pH oxalic-rich natural waters. The more soluble sodium phase is unlikely to exist in natural waters. The two phases are metastable relative to crystalline gibbsite and may be considered as the first precipitation step in the transition from aqueous Al oxalates down to stable Al hydroxide. Model calculations illustrating these competing hydrolysis-complexation reactions are discussed in terms of predominance and speciation diagrams. The solid phases have been characterized by X-ray analysis of powders, TGA and IR spectra, and tentative structures are proposed. Phase I seems to be an octahedral layer structure, in which 3/5 of the octahedral sites between two close packed oxygen sheets are occupied by Al 3+ and the oxalate ion acts as a bridge ligand between two aluminium atoms. Phase II forms a more open sheet structure and has ion exchange properties. Powder data for a phase crystallized from the studied solution after a year are also presented. This phase, Na 4Al 2(OH) 2(C 2O 4) 4 · 10H 2O, supports the results from the equilibrium analysis of recent solution data by SJöBERG and ÖHMAN (1985), who have found the dinuclear complex Al 2(OH) 2(C 2O 4) 44- to exist in a

EPR study of the production of OH radicals in aqueous solutions of uranium irradiated by ultraviolet light

Directory of Open Access Journals (Sweden)

MARKO DAKOVIĆ

2009-06-01

Full Text Available The aim of the study was to establish whether hydroxyl radicals (•OH were produced in UV-irradiated aqueous solutions of uranyl salts. The production of •OH was studied in uranyl acetate and nitrate solutions by an EPR spin trap method over a wide pH range, with variation of the uranium concentrations. The production of •OH in uranyl solutions irradiated with UV was unequivocally demonstrated for the first time using the EPR spin-trapping method. The production of •OH can be connected to speciation of uranium species in aqueous solutions, showing a complex dependence on the solution pH. When compared with the results of radiative de-excitation of excited uranyl (*UO22+ by the quenching of its fluorescence, the present results indicate that the generation of hydroxyl radicals plays a major role in the fluorescence decay of *UO22+. The role of the presence of carbonates and counter ions pertinent to environmental conditions in biological systems on the production of hydroxyl radicals was also assessed in an attempt to reveal the mechanism of *UO22+ de-excitation. Various mechanisms, including •OH production, are inferred but the main point is that the generation of •OH in uranium containing solutions must be considered when assessing uranium toxicity.

The role anions on the synthesis of AlOOH nanoparticles using simple solvothermal method

Directory of Open Access Journals (Sweden)

Mozaffar Abdollahifar

2018-03-01

Full Text Available Effect of aluminium salts on the synthesis of AlOOH nanostructures has been successfully investigated in detail using solvothermal method, when ethanol and NaOH are solvent and pH adjusting agent, respectively. Fourier transform infrared spectroscopy (FTIR, X-ray powder diffraction (XRD, and field emission scanning electron microscopy (FESEM, were used to characterize the synthesized samples. The specific surface area, pore size distribution and pore structure of the different AlOOH structures were also discussed by the N2 adsorption/desorption test. According to our experimental results, the structure characterization revealed that for synthesized AlOOH nanostructures no obvious XRD peaks arising from other phases of alumina are found indicating pure AlOOH phase of products. Furthermore, the nitrogen adsorption and desorption measurements indicated that the obtained AlOOH nanoparticles from aluminium chloride at basic condition possess a high BET surface area of approximately 90 m2/g. Resumen: El efecto de las sales de aluminio sobre la síntesis de las nanoestructuras de AlOOH ha sido analizado en detalle satisfactoriamente usando el método solvotérmico, cuando el etanol y el NaOH son el disolvente y el agente de regulación del pH, respectivamente. Para clasificar las muestras sintetizadas se utilizaron la espectroscopia infrarroja por transformada de Fourier (FTIR, difracción de rayos X por polvo (XRD y microscopia electrónica de barrido de emisión de campo (FESEM. El área superficial específica, la distribución del tamaño del poro y la estructura de poros de las diferentes estructuras de AlOOH también se debatieron mediante la prueba de adsorción/desorción de N2. De acuerdo con nuestros resultados experimentales, la clasificación de la estructura reveló que en las nanoestructuras de AlOOH sintetizadas no se observan picos XRD evidentes derivados de otras fases de la alúmina que indican la fase pura de AlOOH de los productos

Estabilidade da sílica biogênica extraída de capim Jaraguá (Hyparrhenia rufa em solução de NaOH Stability of biogenic silica extract of Jaraguá grass (Hyparrhenia rufa in NaOH solution

Directory of Open Access Journals (Sweden)

Liovando M. Costa

2010-01-01

Full Text Available Biogenic silica is used to describe compounds of hydrated silica (SiO2.nH2O, with specific shapes and sizes, deposited in plants. The chemical composition of biogenic silica and its stability in Jaraguá grass was studied in increasing concentration of NaOH. The analytical results demonstrated high concentration of Si, Al, Fe, Mg, P and low of Cu, Cd and Zn in the phytoliths composition. The silica bodies stability in NaOH solution with increasing concentration was different among the shapes and sizes. Silicified stomata and silicified plant tissues were dissolved along with the dumbbells because they are the less stable forms of biogenic silica.

Brief Exposures to the Taste of Ethanol (EtOH) and Quinine Promote Subsequent Acceptance of EtOH in a Paradigm that Minimizes Postingestive Consequences.

Science.gov (United States)

Loney, Gregory C; Meyer, Paul J

2018-03-01

Aversion to the orosensory properties of concentrated ethanol (EtOH) solutions is often cited as a primary barrier to initiation of drinking and may contribute to abstention. These aversive properties include gustatory processes which encompass both bitter-like taste qualities and trigeminal-mediated irritation. Chronic intermittent EtOH access (CIA) results in substantial and persistent increases in EtOH consumption, but the degree to which this facilitation involves sensory responding to EtOH and other bitter stimuli is currently undetermined. Long-Evans rats were given brief-access licking tests designed to examine the immediate, taste-guided assessment of the palatability of EtOH and quinine solutions. Rats were assessed once in a naïve state and again following previous brief-access exposure, or following 4 weeks of CIA. The relationship between the sensitivity to the aversive orosensory properties of EtOH and quinine following EtOH access and the impact of antecedent quinine exposure on the acceptance of EtOH were determined in 2 parallel studies. Both brief access to EtOH and 4-week CIA resulted in substantial rightward shifts in the concentration-response function of brief-access EtOH licking, indicating that EtOH exposure increased acceptance of the taste of EtOH. The initial sensitivity to the aversive orosensory properties of EtOH and quinine was positively correlated in naïve rats, such that rats that were initially more accepting of quinine were also more accepting of EtOH. Rats that sampled quinine immediately prior to tasting EtOH exhibited successive positive contrast in that they were more accepting of highly concentrated EtOH, relative to a water-control group. Increased EtOH acceptance following exposure is, at least in part, facilitated by a decrease in its aversive sensory properties. Both long- and short-term access increase the palatability of the taste of EtOH in brief-access licking tests. Moreover, the sensitivity to the bitterness of

Infrared and Raman spectroscopic characterization of the silicate mineral olmiite CaMn2+[SiO3(OH)](OH) - implications for the molecular structure

Science.gov (United States)

Frost, Ray L.; Scholz, Ricardo; López, Andrés; Xi, Yunfei; Granja, Amanda; Žigovečki Gobac, Željka; Lima, Rosa Malena Fernandes

2013-12-01

We have studied the mineral olmiite CaMn[SiO3(OH)](OH) which forms a series with its calcium analogue poldervaartite CaCa[SiO3(OH)](OH) using a range of techniques including scanning electron microscopy, thermogravimetric analysis, Raman and infrared spectroscopy. Chemical analysis shows the mineral is pure and contains only calcium and manganese in the formula. Thermogravimetric analysis proves the mineral decomposes at 502 °C with a mass loss of 8.8% compared with the theoretical mass loss of 8.737%. A strong Raman band at 853 cm-1 is assigned to the SiO stretching vibration of the SiO3(OH) units. Two Raman bands at 914 and 953 cm-1 are attributed to the antisymmetric vibrations. Two intense Raman bands observed at 3511 and 3550 cm-1 are assigned to the OH stretching vibration of the SiO3(OH) units. The observation of multiple OH bands supports the concept of the non-equivalence of the OH units. Vibrational spectroscopy enables a detailed assessment of the molecular structure of olmiite.

Subglacial hydrothermal alteration minerals in Jökulhlaup deposits of Southern Iceland, with implications for detecting past or present habitable environments on Mars.

Science.gov (United States)

Warner, Nicholas H; Farmer, Jack D

2010-06-01

Jökulhlaups are terrestrial catastrophic outfloods, often triggered by subglacial volcanic eruptions. Similar volcano-ice interactions were likely important on Mars where magma/lava may have interacted with the planet's cryosphere to produce catastrophic floods. As a potential analogue to sediments deposited during martian floods, the Holocene sandurs of Iceland are dominated by basaltic clasts derived from the subglacial environment and deposited during jökulhlaups. Palagonite tuffs and breccias, present within the deposits, represent the primary alteration lithology. The surface abundance of palagonite on the sandurs is 1-20%. X-ray diffraction (XRD) analysis of palagonite breccias confirms a mineral assemblage of zeolites, smectites, low-quartz, and kaolinite. Oriented powder X-ray diffractograms (habitable environments for microbial life may be found.

OH Solar Radiometer

Data.gov (United States)

National Aeronautics and Space Administration — The abundance of the hydroxyl radical, OH, determines the lifetime of methane and its global warming potential. Despite the growing importance of methane and the...

Ordering and structural vacancies in non-stoichiometric Cu-Al γ brasses

International Nuclear Information System (INIS)

Kisi, E.H.; Browne, J.D.

1991-01-01

γ-Brass structures are based on the cubic packing of 26-atom clusters which have, as concentric subunits, an inner and an outer tetrahedron (IT, OT), an octahedron (OH) and a cuboctahedron (CO). Cu 9 Al 4 [M r = 679.37, P43m, a = 8.7046(1) A, V = 659.5 A 3 , Z = 4, D x = 6.846 Mg m -3 , R wp = 0.051, R B = 0sun017 for 238 powder reflections] is the stoichiometric γ brass of the Cu-Al system and contains two clusters (A, B) per unit cell. Al atoms occupy a 4(e) (IT) site in cluster A and a 12(i) (CO) site in cluster B. Cu atoms occupy the remaining 4(e) (OT), 6(f) (OH) and 12(i) (CO) sites of cluster A and the two 4(e) (IT, OT) and a 6(g) (OH) site of cluster B. The structure has considerable solubility for Al and this paper contains a systematic neutron powder diffraction study of the changes in the Cu 9 Al 4 structure at 295 K (λ = 1.376 A) and 77 K(λ = 1.500 A) as Al is added. The structure was found to remain cubic for compositions Cu 8.93 Al 4.08 , Cu 8.83 , Al 4.17 , Cu 8.75 Al 4.25 and Cu 8.58 Al 4.42 . At Cu 8.30 Al 4.58 the structure was slightly distorted to an undetermined symmetry. For Cu 8.03 Al 4.68 and Cu 7.55 Al 4.80 the structure was found to be rhombohedral [M r = 636.57, R3m, a = 8.7066(1) A, α = 89.74(1) deg, V = 660.0(1) A 3 , Z = , D x = 6.406, D m = 6.41 Mg m -3 , R wp = 0.064, R B = 0.025 for 702 reflections; and M r = 609.31, R3m, a = 8.6884(1) A, α = 89.78(1) deg, V = 655.9(1) A 3 , Z = 4, D x = 6.170, D m = 6.18 Mg m -3 , R wp = 0.064, R B = 0.027 for 789 reflections, respectively]. The non-cubic structures contain sufficient structural vacancies to maintain a classical valence content of 88 electrons per unit cell. Refined structures are presented for all of the above compositions, except Cu 8.30 Al 4.58 , and the results discussed in terms of current γ-brass stability theories. (orig.)

A search for OH emission from symbiotic stars

International Nuclear Information System (INIS)

Norris, R.P.; Haynes, R.F.; Wright, A.E.

1984-01-01

A search was made for OH maser emission from a sample of 16 symbiotic stars. This sample was selected on the basis of infrared optical depth and variability, so that the stars within it have circumstellar shells similar to those seen in OH/IR and OH/Mira stars. There were no significant detections, except for one unassociated background source, and it is concluded that the presence of a hot binary companion inhibits any possible OH maser action

Improvement of selective removal of heavy metals in cyanobacteria by NaOH treatment.

Science.gov (United States)

Nagase, Hiroyasu; Inthorn, Duangrat; Oda, Aiko; Nishimura, Jun; Kajiwara, Yumiko; Park, Myong-Oku; Hirata, Kazumasa; Miyamoto, Kazuhisa

2005-04-01

In the freshwater cyanobacterium, Tolypothrix tenuis, treatment with 0.1 M NaOH increased its Cd-selective adsorption ability in the presence of Ca(2+) or Mg(2+). The selective adsorption was also achieved by other alkaline treatments. Energy-distributed spectroscopy analysis revealed that Cd(2+) was found mainly on the surface of non-treated cells, whereas it was distributed throughout the cell after NaOH treatment. The alkaline treatment was effective in increasing the selective adsorption ability of the cyanobacterium for other bivalent heavy metals such as Cu(2+), Pb(2+) and Zn(2+). The treatment was also applicable to Anabaena variabilis and Microcystis aeruginosa, which are typical cyanobacteria causing algal blooms. The main binding site of Cd(2+) in NaOH-treated cells is assumed to be the carboxyl groups because the binding ability of the cells was diminished by the esterification of carboxyl groups. These results suggest that alkaline treatment of cyanobacteria is a useful technique for producing biosorbents having highly specific binding abilities for heavy metals.

Synthesis, structure, and spectroscopic and magnetic characterization of [Mn12O12(O2CCH2But)16(MeOH)4]·MeOH, a Mn12 single-molecule magnet with true axial symmetry.

Science.gov (United States)

Lampropoulos, Christos; Murugesu, Muralee; Harter, Andrew G; Wernsdofer, Wolfgang; Hill, Stephen; Dalal, Naresh S; Reyes, Arneil P; Kuhns, Philip L; Abboud, Khalil A; Christou, George

2013-01-07

The synthesis and properties are reported of a rare example of a Mn(12) single-molecule magnet (SMM) in truly axial symmetry (tetragonal, I4). [Mn(12)O(12)(O(2)CCH(2)Bu(t))(16)(MeOH)(4)]·MeOH (3·MeOH) was synthesized by carboxylate substitution on [Mn(12)O(12)(O(2)CMe)(16)(H(2)O)(4)]·2MeCO(2)H·4H(2)O (1). The complex was found to possess an S = 10 ground state, as is typical for the Mn(12) family, and displayed both frequency-dependent out-of-phase AC susceptibility signals and hysteresis loops in single-crystal magnetization vs DC field sweeps. The loops also exhibited quantum tunneling of magnetization steps at periodic field values. Single-crystal, high-frequency electron paramagnetic resonance spectra on 3·MeOH using frequencies up to 360 GHz revealed perceptibly sharper signals than for 1. Moreover, careful studies as a function of the magnetic field orientation did not reveal any satellite peaks, as observed for 1, suggesting that the crystals of 3 are homogeneous and do not contain multiple Mn(12) environments. In the single-crystal (55)Mn NMR spectrum in zero applied field, three well-resolved peaks were observed, which yielded hyperfine and quadrupole splitting at three distinct sites. However, observation of a slight asymmetry in the Mn(4+) peak was detectable, suggesting a possible decrease in the local symmetry of the Mn(4+) site. Spin-lattice (T(1)) relaxation studies were performed on single crystals of 3·MeOH down to 400 mK in an effort to approach the quantum tunneling regime, and fitting of the data using multiple functions was employed. The present work and other recent studies continue to emphasize that the new generation of truly high-symmetry Mn(12) complexes are better models for thorough investigation of the physical properties of SMMs than their predecessors such as 1.

Young planetary nebula with OH molecules - NGC 6302

International Nuclear Information System (INIS)

Payne, H.E.; Phillips, J.A.; Terzian, Y.

1988-01-01

The results of a sensitive survey of planetary nebulae in all four ground-state OH lines are reported. The results confirm that evolved planetary nebulas are not OH sources in general. However, one interesting object was not detected: an OH 1612 MHz maser in the young planetary nebula NGC 6302. This nebula may be in a brief evolutionary stage, similar to the young and compact planetary nebula Vy 2-2, where OH has already been detected. In addition, the results of further observations of NGC 6302 are reported, including VLA observations of the 1612 MHz line and continuum emission and detections of rotationally excited OH lines at 5-cm wavelength in absorption. 28 references

The electrochemical properties and mechanism of formation of anodic oxide films on Mg-Al alloys

International Nuclear Information System (INIS)

Kim, Seong Jong; Okido, Masazumi

2003-01-01

The electronchemical properties and the mechanism of formation of anodic oxide films on Mg alloys containing 0-15 mass% Al, when anodized in NaOH solution, were investigated by focusing on the effects of anodizing potential, Al content, and anodizing time. The intensity ratio of Mg(OH) 2 in the XRD analysis decreased with increasing applied potential, while that of MgO increased. Mg(OH) 2 was barely detected at 80 V, while MgO was readily detected. The anti-corrosion properties of anodized specimens at each constant potential were better than those of non-anodized specimens. The specimen anodized at an applied potential of 3 V had the best anti-corrosion property. The intensity ratio of the β phase increased with aluminum content in Mg-Al alloys. During anodizing, the active dissolution reaction occurred preferentially in β phase until about 4 min, and then the current density increased gradually until 7 min. The dissolution reaction progressed in α phase, which had a lower Al content. In the anodic polarization test in 0.017 mol·dm -3 NaCl and 0.1 mol·dm -3 Na 2 SO 4 at 298 K, the current density of Mg-15 mass% Al alloy anodized for 10 min increased, since the anodic film that forms on the α phase is a non-compacted film. The anodic film on the α phase at 30 min was a compact film as compared with that at 10 min

OH detection by Ford Motor Company

Science.gov (United States)

Wang, Charles C.

1986-12-01

Two different methods for detection of OH are presented: a low pressure flow cell system and a frequency modulation absorption measurement. Using conventional absorption spectroscopy, detection limits were quoted of 1,000,000 OH molecules per cu cm using a 30-minute averaging time on the ground, and a 3-hour averaging time in the air for present apparatus in use. With the addition of FM spectroscopy at 1 GHz, a double-beam machine should permit detectable absorption of and an OH limit of 100,000 per cu cm in a 30-minute averaging time. In the low pressure system on which experiments are ongoing nonexponential time behavior was observed after the decay had progressed to about 0.3 of its original level; this was attributed to ion emission in the photomultiplier. A flame source with OH present at high concentration levels was used as a calibration. It was estimated that within the sampling chamber, 400,000 OH could be measured. With a factor-of-2 loss at the sampling orifice, this means detectability of 5 to 8 x 100,000 cu cm at the present time. This could be reduced by a factor of 2 in one hour averaging time; improvements in laser bandwidth and energy should provide another factor of 2 in sensitivity.

oh sport

Directory of Open Access Journals (Sweden)

Elena Grigoryeva

2017-03-01

Sports play a very important and diverse role in the present-day global culture. On the occasion of the 105th anniversary of Coubertin’s Ode we would like to wish sports to return to the main words of the Ode and to correspond with them: “Oh sport, you are the peace”.

Comparative effect of Al, Se, and Mo toxicity on NO3(-) assimilation in sunflower (Helianthus annuus L.) plants.

Science.gov (United States)

Ruiz, Juan M; Rivero, Rosa M; Romero, Luis

2007-04-01

Here, we study the effect caused by three trace elements--Al, Se, and Mo--applied at the same concentration (100 microM) and in their oxyanionic forms--NaAl(OH)(4), Na(2)SeO(4), and Na(2)MoO(4)--on NO(3)(-) assimilation (NO(3)(-), nitrate reductase (NR), nitrite reductase (NiR), glutamine synthetase (GS), and glutamate synthase (GOGAT) activities, and concentrations of amino acids and proteins) in sunflower (Helianthus annuus L. var. Kasol) plants. The most harmful element for sunflower plants proved to be selenate, followed by aluminate. On the contrary, the application of molybdate had no negative effect on the growth of this plant, suggesting the possibility of using sunflower for the phytoremediation of this metal, mainly in agricultural zones used for grazing where the excess of this element can provoke problems of molybdenosis in ruminants (particularly in cattle). In addition, we found that the alteration of NO(3)(-) assimilation by SeO(4)(2-) and Al(OH)(4)(-) directly influences the growth and development of plants, foliar inhibition of NR activity by SeO(4)(2-) being more harmful than the decrease in foliar availability of NO(3)(-) provoked by Al(OH)(4)(-).

AlOx Coating of Ultrastable Zeolite Y: A Possible Method for Vanadium Passivation of FCC Catalysts

NARCIS (Netherlands)

Weckhuysen, B.M.; Catana, Gabriela; Grünert, W.; Voort, P. van der; Vansant, E.F.; Schoonheydt, R.A.

2000-01-01

AlOx coating is proposed as a possible method for vanadium passivation of the ultrastable zeolite Y (USY). Two coating methods are discussed: (i) the deposition of the [Al13O4(OH)24(H2O)12]7+ ([Al13]) complex from aqueous solutions and (ii) the anchoring of alumoxane by in situ triisobutylaluminum

OH outflows in star-forming regions

International Nuclear Information System (INIS)

Mirabel, I.F.; Ruiz, A.; Rodriguez, L.F.; Canto, J.; Universidad de Puer; Universidad de Puerto Rico, Rio Piedras; Universidad Nacional Autonoma de Mexico, Mexico City)

1987-01-01

The results from a survey for high-velocity OH in molecular outflows in star-forming regions are reported. High-velocity OH was detected in absorption in nine of these regions. When the telescope beam can resolve the outflows, they show similar anisotropic angular distribution as the redshifted and blueshifted CO. The OH transitions are markedly subthermal since for several sources it is found that the radiation that is being absorbed is a background continuum constituted by the cosmic component plus a small Galactic contribution. The absorbing OH appears to trace gas with higher velocities and lower densities than does the CO and, in some cases, provides information on the structure of the outflows at larger distances from the central source. At scales of 0.1 pc, the outflows are elongated in the direction of the steepest density gradient of the ambient cloud, suggesting that the large-scale collimation of the outflow is produced by the density structure of the ambient cloud. 29 references

Development of Al2O3 carrier-Ru composite catalyst for hydrogen generation from alkaline NaBH4 hydrolysis

International Nuclear Information System (INIS)

Huang, Yao-Hui; Su, Chia-Chi; Wang, Shu-Ling; Lu, Ming-Chun

2012-01-01

A recyclable and reusable Ru/Al 2 O 3 catalyst is prepared for hydrogen generation from the hydrolysis process of alkaline sodium borohydride (NaBH 4 ) solution. The hydrogen generation rate by the hydrolysis and methanolysis of alkaline NaBH 4 was explored as a function of NaOH concentration. Meantime, the byproducts derived from the spent alkaline NaBH 4 solution were characterized by X-ray diffraction (XRD), scanning electro microscope/energy dispersive spectrometer (SEM/EDS) and NMR (Nuclear Magnetic Resonance). The effect of NaOH concentration on the hydrogen generation from the hydrolysis of NaBH 4 significantly depends on the type of catalysts. With increasing NaOH concentration, the hydrogen generation rates decrease when using ruthenium (Ru) composite as a catalyst. The hydrogen generation rate of the methanolysis of NaBH 4 is significantly inhibited in the presence of NaOH as compared with the hydrolysis of NaBH 4 . The durability test of the Ru/Al 2 O 3 catalyst shows that the hydrogen generation rate decreases with recycling and reuse. The XRD and NMR analysis results show that the borate hydrate (NaBO 2 H 2 O) was derived from the hydrolysis of 20 wt% and 30 wt% NaBH 4 . -- Highlights: ► A recyclable Ru/Al 2 O 3 catalyst was synthesized for hydrogen generation. ► Ru/Al 2 O 3 significantly promotes the hydrogen generation rate from alkaline NaBH 4 solution. ► The prepared Ru/Al 2 O 3 catalyst can easily collect from the spent alkaline NaBH 4 solution.

Optimization and kinetics decomposition of monazite using NaOH

International Nuclear Information System (INIS)

MV Purwani; Suyanti; Deddy Husnurrofiq

2015-01-01

Decomposition of monazite with NaOH has been done. Decomposition performed at high temperature on furnace. The parameters studied were the comparison NaOH / monazite, temperature and time decomposition. From the research decomposition for 100 grams of monazite with NaOH, it can be concluded that the greater the ratio of NaOH / monazite, the greater the conversion. In the temperature influences decomposition 400 - 700°C, the greater the reaction rate constant with increasing temperature greater decomposition. Comparison NaOH / monazite optimum was 1.5 and the optimum time of 3 hours. Relations ratio NaOH / monazite with conversion (x) following the polynomial equation y = 0.1579x 2 – 0.2855x + 0.8301 (y = conversion and x = ratio of NaOH/monazite). Decomposition reaction of monazite with NaOH was second orde reaction, the relationship between temperature (T) with a reaction rate constant (k), k = 6.106.e - 1006.8 /T or ln k = - 1006.8/T + 6.106, frequency factor A = 448.541, activation energy E = 8.371 kJ/mol. (author)

OH Airglow and Equatorial Variations Observed by ISUAL Instrument on Board the FORMOSAT 2 Satellite

Directory of Open Access Journals (Sweden)

Jan-Bai Nee

2010-01-01

Full Text Available OH airglow observed by the ISUAL (Imager of Sprites and Upper Atmospheric Lightning instrument on board the FORMOSAT 2 satellite is reported in this paper. The satellite is sun-synchronous and it returns to the same orbit at the same local time daily. By using this property, we can study the upper atmosphere in detail. With a CCD camera, ISUAL has measured the emission layers of OH Meinel band at 630 nm for several two-week periods in 2004 and 2007 in equatorial regions. ISUAL images are snapshots of the atmosphere 250 km (height ¡_ 1200 km (horizontal distance. These images of OH airglow are analyzed to derive its peak height and latitudinal variations. ISUAL observation is unique in its capability of continuous observation of the upper atmosphere as the satellite travels from south to north along a specific orbit. However, 630 nm filter also measured O(1D at 200 km, and there are interferences between O(1D and OH airglows as as observed from a distance in space. We have studied the overlap of two airglows by simulations, and our final analyses show that OH airglow can be correctly derived with its average peak height of 89 ¡_ 2.1 km usually lying within ¡_10¢X latitude about the equator. ISUAL data reveal detailed structures of equatorial OH airglow such as the existences of a few secondary maxima within the equatorial regions, and the oscillations of the peak latitudes. These results are discussed and compared with previous reports.

Conformal coating of Ni(OH)2 nanoflakes on carbon fibers by chemical bath deposition for efficient supercapacitor electrodes

KAUST Repository

Alhebshi, Nuha

2013-01-01

A novel supercapacitor electrode structure has been developed in which a uniform and conformal coating of nanostructured Ni(OH)2 flakes on carbon microfibers is deposited in situ by a simple chemical bath deposition process at room temperature. The microfibers conformally coated with Ni(OH) 2 nanoflakes exhibit five times higher specific capacitance compared to planar (non-conformal) Ni(OH)2 nanoflake electrodes prepared by drop casting of Ni(OH)2 powder on the carbon microfibers (1416 F g-1vs. 275 F g-1). This improvement in supercapacitor performance can be ascribed to the preservation of the three-dimensional structure of the current collector, which is a fibrous carbon fabric, even after the conformal coating of Ni(OH)2 nanoflakes. The 3-D network morphology of the fibrous carbon fabric leads to more efficient electrolyte penetration into the conformal electrode, allowing the ions to have greater access to active reaction sites. Cyclic stability testing of the conformal and planar Ni(OH)2 nanoflake electrodes, respectively, reveals 34% and 62% drop in specific capacitance after 10 000 cycles. The present study demonstrates the crucial effect that electrolyte penetration plays in determining the pseudocapacitive properties of the supercapacitor electrodes. © 2013 The Royal Society of Chemistry.

Coal demineralization with Ca(OH)2. Hydrothermal reaction between Ca(OH)2 and quartz; Ca(OH)2 wo mochiita sekitan no kagakuteki dakkai. Ca(OH)2 to sekitan no suinetsu hanno

Energy Technology Data Exchange (ETDEWEB)

Wang, J.; Tomita, A. [Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science

1996-10-28

Coal demineralization mechanism and its optimum condition were studied by hydrothermal reaction between Ca(OH)2 and quartz as a coal demineralization model. In experiment, the mixture of powder quartz and Ca(OH)2 water slurry was subjected to reaction in an autoclave under spontaneous pressure at 175-340{degree}C. After dried in N2 gas atmosphere at 105{degree}C, the reaction product was analyzed by X-ray diffraction, thermo-balance and differential thermal analysis. In measurement of quartz conversion, the specimen was analyzed by X-ray diffraction after removal of bound water by heat treatment at 850{degree}C. The mixture of clean coal deashed by NaOH and a fixed amount of quartz was also used as specimen for experiment. As the experimental result, dicalcium silicate hydrate was mainly produced at 175{degree}C, and the product changed into xonotlite through tobermorite by longer treatment at higher temperature. For complete reaction of quartz, heat treatments for 7 and 5 hours at 300 and 400{degree}C were necessary, respectively. 2 refs., 2 figs., 2 tabs.

Constraints on the OH-to-H Abundance Ratio in Infrared-bright Galaxies Derived from the Strength of the OH 35 μm Absorption Feature

Science.gov (United States)

Stone, Myra; Veilleux, Sylvain; González-Alfonso, Eduardo; Spoon, Henrik; Sturm, Eckhard

2018-02-01

We analyze Spitzer/InfraRed Spectrograph (IRS) observations of the OH 35 μm feature in 15 nearby (z ≲ 0.06) (ultra-)luminous infrared galaxies (U/LIRGs). All objects exhibit OH 35 μm purely in absorption, as expected. The small optical depth of this transition makes the strength of this feature a good indicator of the true OH column density. The measured OH 35 μm equivalent widths imply an average OH column density and a 1-σ standard deviation to the mean of {N}{OH}=1.31+/- 0.22× {10}17 cm‑2. This number is then compared with the hydrogen column density for a typical optical depth at 35 μm of ∼0.5 and gas-to-dust ratio of 125 to derive an OH-to-H abundance ratio of {X}{OH}=1.01+/- 0.15× {10}-6. This abundance ratio is formally a lower limit. It is consistent with the values generally assumed in the literature. The OH 35 μm line profiles predicted from published radiative transfer models constrained by observations of OH 65, 79, 84, and 119 μm in 5 objects (Mrk 231, Mrk 273, IRAS F05189-2524, IRAS F08572+3915, and IRAS F20551-4250) are also found to be consistent with the IRS OH 35 μm spectra.

Interactions between kaolinite Al−OH surface and sodium hexametaphosphate

Energy Technology Data Exchange (ETDEWEB)

Han, Yonghua, E-mail: hyh19891102@163.com [School of Chemical and Environmental Engineering, China University of Mining and Technology, Beijing 100083 (China); Liu, Wenli; Zhou, Jia [School of Chemical and Environmental Engineering, China University of Mining and Technology, Beijing 100083 (China); Chen, Jianhua [College of Resources and Metallurgy, Guangxi University, Nanning 530004 (China)

2016-11-30

Highlights: • Sodium hexametaphosphate (NaHMP) can adsorb on kaolinite Al−OH terminated (001) surface easily. • The oxygen atoms of hexametaphosphate form strong hydrogen bonds with the hydrogen atoms of kaolinite Al−OH surface. • The electrostatic force is the main interaction between NaHMP and Al−OH surface. • The linear hexaphosphate −[PO{sub 3}]{sub m}− chains adsorb stably than −[HPO{sub 3}]{sub m}− chains. - Abstract: To investigate the dispersion mechanism of sodium hexametaphosphate on kaolinite particles, we simulated the interaction between linear polyphosphate chains and kaolinite Al−OH terminated surface by molecular dynamics, as well as the interaction between the [HPO{sub 4}]{sup 2−} anion and kaolinite Al−OH surface by density functional theory (DFT). The calculated results demonstrate that hexametaphosphate can be adsorbed by the kaolinite Al−OH surface. The oxygen atoms of hexametaphosphate anions may receive many electrons from the Al−OH surface and form hydrogen bonds with the hydrogen atoms of surface hydroxyl groups. Moreover, electrostatic force dominates the interactions between hexametaphosphate anions and kaolinite Al−OH surface. Therefore, after the adsorption of hexametaphosphate on kaolinite Al−OH surface, the kaolinite particles carry more negative charge and the electrostatic repulsion between particles increases. In addition, the adsorption of −[PO{sub 3}]{sub m}− species on the Al−OH surface should be more stable than the adsorption of −[HPO{sub 3}]{sub m}− species.

The reactivity of anion-exchange resins by applying OT-for-OH exchange reaction in the equilibrium state

International Nuclear Information System (INIS)

Kano, Naoki; Nihei, Makoto; Imaizumi, Hiroshi

1996-01-01

In order to reveal the behavior of hydroxyl group in isotope exchange reaction, OT-for-OH exchange reaction between each anion-exchange resin (OH - form) and tritiated water (abbreviated as HTO water below) was observed at 80degC under the equilibrium. Anion-exchange resins used were Amberlite IRA-400, IRA-410 (both strongly basic), and IRA-94S (weakly basic). It can be thought that an HTO molecule dissociates into H + +OT - (or T + +OH - ). The activity of each resin based on OT-for-OH exchange reaction was measured with a liquid scintillation counter. From the above-mentioned, the following five were found. Isotope exchange reaction as 'atomic group' occurred between the OH group in each anion-exchange resin and the OT group in HTO water. The reactivity of strongly basic anion-exchange resin is larger than that of weakly basic one. The ratio of the reactivity of these resins can roughly be expressed as follows: (IRA-410): (IRA-400): (IRA-94S)=42: 7: 1. The degree of OT-for-OH exchange reaction may be smaller than that of T-for-H exchange reaction. The method used and results obtained in this work may be helpful to obtain the data for the prevention of T-contamination, especially to obtain the data from certain atomic groups including T. (author)

Integrating multi-omics analyses of Nonomuraea dietziae to reveal the role of soybean oil in [(4'-OH)MeLeu]4-CsA overproduction.

Science.gov (United States)

Liu, Huanhuan; Huang, Di; Jin, Lina; Wang, Cheng; Liang, Shaoxiong; Wen, Jianping

2017-07-14

Nonomuraea dietziae is a promising microorganism to mediate the region-specific monooxygenation reaction of cyclosporine A (CsA). The main product [(4'-OH)MeLeu] 4 -CsA possesses high anti-HIV/HCV and hair growth-stimulating activities while avoiding the immunosuppressive effect of CsA. However, the low conversion efficiency restricts the clinical application. In this study, the production of [(4'-OH)MeLeu] 4 -CsA was greatly improved by 55.6% from 182.8 to 284.4 mg/L when supplementing soybean oil into the production medium, which represented the highest production of [(4'-OH)MeLeu] 4 -CsA so far. To investigate the effect of soybean oil on CsA conversion, some other plant oils (corn oil and peanut oil) and the major hydrolysates of soybean oil were fed into the production medium, respectively. The results demonstrated that the plant oils, rather than the hydrolysates, could significantly improve the [(4'-OH)MeLeu] 4 -CsA production, suggesting that soybean oil might not play its role in the lipid metabolic pathway. To further unveil the mechanism of [(4'-OH)MeLeu] 4 -CsA overproduction under the soybean oil condition, a proteomic analysis based on the two-dimensional gel electrophoresis coupled with MALDI TOF/TOF mass spectrometry was implemented. The results showed that central carbon metabolism, genetic information processing and energy metabolism were significantly up-regulated under the soybean oil condition. Moreover, the gas chromatography-mass spectrometry-based metabolomic analysis indicated that soybean oil had a great effect on amino acid metabolism and tricarboxylic acid cycle. In addition, the transcription levels of cytochrome P450 hydroxylase (CYP) genes for CsA conversion were determined by RT-qPCR and the results showed that most of the CYP genes were up-regulated under the soybean oil condition. These findings indicate that soybean oil could strengthen the primary metabolism and the CYP system to enhance the mycelium growth and the

Characteristics of infrared point sources associated with OH masers

International Nuclear Information System (INIS)

Mu Jimang; Esimbek, Jarken; Zhou Jianjun; Zhang Haijuan

2010-01-01

We collect 3249 OH maser sources from the literature published up to April 2007, and compile a new catalog of OH masers. We look for the exciting sources of these masers and their infrared properties from IRAS and MSX data, and make a statistical study. MSX sources associated with stellar 1612 MHz OH masers are located mainly above the blackbody line; this is caused by the dust absorption of stellar envelopes, especially in the MSX A band. The mid-IR sources associated with stellar OH masers are concentrated in a small region in an [A]-[D] vs. [A]-[E] diagram with a small fraction of contamination; this gives us a new criterion to search for new stellar OH masers and distinguish stellar masers from unknown types of OH masers. IR sources associated with 1612 MHz stellar OH masers show an expected result: the average flux of sources with F60 > F25 increases with increasing wavelength, while those with F60 F25.

Hydroxy-Al and cell-surface negativity are responsible for the enhanced sensitivity of Rhodotorula taiwanensis to aluminum by increased medium pH.

Science.gov (United States)

Zhao, Xue Qiang; Bao, Xue Min; Wang, Chao; Xiao, Zuo Yi; Hu, Zhen Min; Zheng, Chun Li; Shen, Ren Fang

2017-10-01

Aluminum (Al) is ubiquitous and toxic to microbes. High Al 3+ concentration and low pH are two key factors responsible for Al toxicity, but our present results contradict this idea. Here, an Al-tolerant yeast strain Rhodotorula taiwanensis RS1 was incubated in glucose media containing Al with a continuous pH gradient from pH 3.1-4.2. The cells became more sensitive to Al and accumulated more Al when pH increased. Calculations using an electrostatic model Speciation Gouy Chapman Stern indicated that, the increased Al sensitivity of cells was associated with AlOH 2+ and Al(OH) 2 + rather than Al 3+ . The alcian blue (a positively charged dye) adsorption and zeta potential determination of cell surface indicated that, higher pH than 3.1 increased the negative charge and Al adsorption at the cell surface. Taken together, the enhanced sensitivity of R. taiwanensis RS1 to Al from pH 3.1-4.2 was associated with increased hydroxy-Al and cell-surface negativity.

Dissolution of targets for the production of Mo-99: Part 1. Influence of NaOH concentration and the addition of NaNO3 and NaNO2 on the dissolution time

International Nuclear Information System (INIS)

Camilo, Ruth L.; Araujo, Izilda da C.; Mindrisz, Ana C.; Forbicini, Christina A.L.G. de O.

2011-01-01

Faced with global crisis in the production of radioisotope 99 Mo, which product of decay, 99 mTc, is the tracer element most often used in nuclear medicine and accounts for about 80% of all diagnostic procedures in vivo, since September 2008 Brazil is developing the project called Brazilian Multipurpose Reactor (RMB). Within the Brazilian Nuclear Program (PNB) the construction of the RMB, is seen as a long term solution to meet all domestic demand relative to the supply of radioisotopes and radiopharmaceuticals. In the process to be studied to obtain 99 Mo from irradiated UA1 x -A1 LEU targets employing alkaline dissolution, processing time should be minimized, considering the short half life of 99 Mo and 99 mTc, about 66 h and 6 h, respectively. That makes dissolution time a significant factor in the development of the process. This paper presents the results of alkaline dissolution of scraps of Al, used to simulate the dissolution process of UA1 x -A1 targets. Al corresponds to about 79% of the total weight of the UA1 x -A1 target. The effect of NaOH concentration on dissolution time for the interval of 1 to 3.5 mol.L-1 was studied, keeping the molar ratio in 1Al:2.16NaOH and the initial temperature of 88 degree C. The influence of reagent composition over dissolution time was studied using three different solutions: a) 3 mol.L -1 NaOH, b) 3 mol.L -1 NaOH/NaNO 3 and c) 3 mol.L -1 NaOH/NaNO 2 , keeping the same molar ratio and temperature. The results showed that the dissolution time decreases with increasing NaOH concentration and the addition of NaNO 3 or NaNO 2 in the NaOH solution reduces both dissolution time and volume of gases released. (author)

Preparation of Mg(OH)_2 hybrid pigment by direct precipitation and graft onto cellulose fiber via surface-initiated atom transfer radical polymerization

International Nuclear Information System (INIS)

Wang, Xiao; Zhang, Yue; Lv, Lihua; Cui, Yongzhu; Wei, Chunyan; Pang, Guibing

2016-01-01

Graphical abstract: - Highlights: • Adsorbed anionic dye molecules are conducive to preferential growth of (0 0 1) plane of Mg(OH)_2 crystal for Mg(OH)_2 pigments. • Uniform coverage of nanosized Mg(OH)_2 pigments on fiber surface is achieved via surface-initiated ATRP. • About 4 wt% of Mg(OH)_2 pigment on fiber surface shortens nearly half of burning time of cellulose. - Abstract: Mg(OH)_2 flame retardant hybrid pigment is synthesized through simultaneous solution precipitation and adsorption of anionic dyes (C.I. Acid Red 6). The Mg(OH)_2 hybrid pigment bearing vinyl groups after surface silane modification is immobilized onto the surface of bromo end-functional cellulose fiber by atom transfer radical polymerization (ATRP). The morphology and structure of Mg(OH)_2 pigments and cellulose fibers grafted with modified pigments are characterized. The thermal properties, flammability and color fastness of cellulose fibers grafted with modified pigments are measured. The results reveal that anionic dye molecules are adsorbed onto Mg(OH)_2 crystals and affect the formation of lamella-like Mg(OH)_2 crystals. The cellulose fiber grafted with modified Mg(OH)_2 hybrid pigment absorbs about four times heat more than original cellulose fiber with about 4% immobilization ratio of pigment, which shortens nearly half of afterflame time and afterglow time.

Effect of allyl alcohol on hepatic transporter expression: Zonal patterns of expression and role of Kupffer cell function

International Nuclear Information System (INIS)

Campion, Sarah N.; Tatis-Rios, Cristina; Augustine, Lisa M.; Goedken, Michael J.; Rooijen, Nico van; Cherrington, Nathan J.; Manautou, Jose E.

2009-01-01

During APAP toxicity, activation of Kupffer cells is critical for protection from hepatotoxicity and up-regulation of multidrug resistance-associated protein 4 (Mrp4) in centrilobular hepatocytes. The present study was performed to determine the expression profile of uptake and efflux transporters in mouse liver following treatment with allyl alcohol (AlOH), a periportal hepatotoxicant. This study also investigated the role of Kupffer cells in AlOH hepatotoxicity, and whether changes in transport protein expression by AlOH are dependent on the presence of Kupffer cells. C57BL/6J mice received 0.1 ml clodronate liposomes to deplete Kupffer cells or empty liposomes 48 h prior to dosing with 60 mg/kg AlOH, i.p. Hepatotoxicity was assessed by plasma ALT and histopathology. Hepatic transporter mRNA and protein expression were determined by branched DNA signal amplification assay and Western blotting, respectively. Depletion of Kupffer cells by liposomal clodronate treatment resulted in heightened susceptibility to AlOH toxicity. Exposure to AlOH increased mRNA levels of several Mrp genes, while decreasing organic anion transporting polypeptides (Oatps) mRNA expression. Protein analysis mirrored many of these mRNA changes. The presence of Kupffer cells was not required for the observed changes in uptake and efflux transporters induced by AlOH. Immunofluorescent analysis revealed enhanced Mrp4 staining exclusively in centrilobular hepatocytes of AlOH treated mice. These findings demonstrate that Kupffer cells are protective from AlOH toxicity and that induction of Mrp4 occurs in liver regions away from areas of AlOH damage independent of Kupffer cell function. These results suggest that Kupffer cell mediators do not play a role in mediating centrilobular Mrp4 induction in response to periportal damage by AlOH

An experimental and theoretical kinetic study of the reaction of OH radicals with tetrahydrofuran

KAUST Repository

Giri, Binod

2016-06-24

Tetrahydrofuran (CHO, THF) and its alkylated derivatives of the cyclic ether family are considered to be promising future biofuels. They appear as important intermediates during the low-temperature oxidation of conventional hydrocarbon fuels and of heavy biofuels such as long-chain fatty acid methyl esters. The reaction of tetrahydrofuran with OH radicals was investigated in a shock tube, over a temperature range of 800-1340 K and at pressures near 1.5 bar. Hydroxyl radicals were generated by the rapid thermal decomposition of tert-butyl hydroperoxide, and a UV laser absorption technique was used to monitor the mole fraction of OH radicals. High-level CCSD(T)/cc-pV(D,T)Z//MP2/aug-cc-pVDZ quantum chemical calculations were performed to explore the chemistry of the THF+OH reaction system. Our calculations reveal that the THF+OH (R1) reaction proceeds via either direct or indirect H-abstraction from various sites, leading to the formation of tetrahydrofuran-2-yl (THF-R2) or tetrahydrofuran-3-yl (THF-R3) radicals and water. Theoretical kinetic analysis revealed that both channels are important under conditions relevant to combustion. To our knowledge, this is the first direct experimental and theoretical kinetic study of the reaction of tetrahydrofuran with OH radicals at high temperatures. The following theoretical rate expressions (in units of cmmols) are recommended for combustion modeling in the temperature range 800-1350 K: . k1(T)=4.11×1040.16em0ex(TK)2.69exp(1316.80.16em0exKT)2.em0ex0.16em0ex(THF+OH→Products) . k2(T)=6.930.16em0ex×10110.16em0ex(TK)0.41exp(-106.80.16em0exKT)2.em0ex0.16em0ex(THF+OH→THF-R20.16em0ex+H2O) . k3(T)=4.120.16em0ex×1030.16em0ex(TK)3.02exp(456.90.16em0exKT)2.em0ex0.16em0ex(THF+OH→THF-R30.16em0ex+H2O) . .

Electrochemically induced transformation of NiS nanoparticles into Ni(OH)2 in KOH aqueous solution toward electrochemical capacitors

International Nuclear Information System (INIS)

Hou Linrui; Yuan Changzhou; Li Diankai; Yang Long; Shen Laifa; Zhang Fang; Zhang Xiaogang

2011-01-01

Highlights: → NiS is synthesized by means of the H 2 O/CS 2 interface under hydrothermal treatment. → NiS itself owns poor electrochemical capacitance in 2 M KOH solution. → NiS is electrochemically induced and transformed into electroactive Ni(OH) 2 . → Ni(OH) 2 is responsible for good energy storage of the NiS in the KOH solution. → The new formed Ni(OH) 2 delivers large energy density at high rates. - Abstract: Nickel sulfide nanoparticles (NPs) are first synthesized by virtue of a unique H 2 O/CS 2 interface under mild hydrothermal treatment. Electrochemical data reveals that the as-synthesized NiS NPs themselves own poor supercapacitive behavior at initial cyclic voltammetry (CV) cycles in 2 M KOH solution, while a specific capacitance of 893 F g -1 can be surprisingly obtained at a current density of 5 A g -1 just after continuous 320 CV cycles. X-ray diffraction and Fourier transform infrared techniques demonstrate that what is really responsible for the good electrochemical capacitance in the KOH aqueous solution is the new electrochemically formed Ni(OH) 2 phase, rather than NiS NPs themselves. The Ni(OH) 2 is slowly formed during the continuous CV cycling process, in which the electrochemically induced phase transformation from NiS to Ni(OH) 2 phase takes place. Furthermore, the new Ni(OH) 2 phase demonstrates the great ability of delivering large specific capacitance at high rates.

Reaction OH + OH studied over the 298-834 K temperature and 1-100 bar pressure ranges.

Science.gov (United States)

Sangwan, Manuvesh; Chesnokov, Evgeni N; Krasnoperov, Lev N

2012-06-21

Self-reaction of hydroxyl radicals, OH + OH → H(2)O + O (1a) and OH + OH → H(2)O(2) (1b), was studied using pulsed laser photolysis coupled to transient UV-vis absorption spectroscopy over the 298-834 K temperature and 1-100 bar pressure ranges (bath gas He). A heatable high-pressure flow reactor was employed. Hydroxyl radicals were prepared using reaction of electronically excited oxygen atoms, O((1)D), produced in photolysis of N(2)O at 193 nm, with H(2)O. The temporal behavior of OH radicals was monitored via transient absorption of light from a dc discharge in H(2)O/Ar low-pressure resonance lamp at ca. 308 nm. The absolute intensity of the photolysis light was determined by accurate in situ actinometry based on the ozone formation in the presence of molecular oxygen. The results of this study combined with the literature data indicate that the rate constant of reaction 1a, associated with the pressure independent component, decreases with temperature within the temperature range 298-414 K and increases above 555 K. The pressure dependent rate constant for (1b) was parametrized using the Troe expression as k(1b,inf) = (2.4 ± 0.6) × 10(-11)(T/300)(-0.5) cm(3) molecule(-1) s(-1), k(1b,0) = [He] (9.0 ± 2.2) × 10(-31)(T/300)(-3.5±0.5) cm(3) molecule(-1) s(-1), F(c) = 0.37.

Studies of Gravity Waves Using Michelson Interferometer Measurements of OH (3-1) Bands

Science.gov (United States)

Won, Young-In; Cho, Young-Min; Lee, Bang Yong; Kim, J.

2001-06-01

As part of a long-term program for polar upper atmospheric studies, temperatures and intensities of the OH (3-1) bands were derived from spectrometric observations of airglow emissions over King Sejong station (62.22o S, 301.25o E). These measurements were made with a Michelson interferometer to cover wavelength regions between 1000 nm and 2000 nm. A spectral analysis was performed to individual nights of data to acquire information on the waves in the upper mesosphere/lower thermosphere. It is assumed that the measured fluctuations in the intensity and temperature of the OH (3-1) airglow were caused by gravity waves propagating through the emission layer. Correlation of intensity and temperature variation revealed oscillations with periods ranging from 2 to 9 hours. We also calculated Krassovsky's parameter and compared with published values.

Uranium dissolution in hyper-alkaline TMA-OH solutions: Preliminary results

Energy Technology Data Exchange (ETDEWEB)

Cachoir, C.; Salah, S.; Mennecart, T.; Lemmens, K. [Belgian Research Nuclear Centre - SCK-CEN, Boeretang 200, 2400 Mol (Belgium)

2016-07-01

Leaching experiments were performed with depleted UO{sub 2} powders in tetramethylammonium solutions (TMA-OH) at pH 13.5 and 12.5, and at different UO{sub 2} surface area to volume of solution (SA/V) ratio's to determine the solubility and the dissolution kinetics of UO{sub 2} at high pH in absence of cations dominating cementitious waters (Ca, Na, K). The solubility of UO{sub 2} increased from pH 12.5 to 13.5 and by increasing the SA/V ratio up to 100 m{sup -1}. However, no known U secondary-phases were predicted by geochemical calculations to control the measured U-concentrations. We interpreted the UO{sub 2} dissolution process as a 2-step process. For all experiments, we observe a fast initial rate, hydroxo promoted and likely surface controlled. Afterwards the rate is apparently negative at low SA/V over time while it is positive at higher SA/V ratio's. The former is interpreted to be related to a sorption process, while the latter reveals a continuous residual dissolution process. No solubility enhancing effect of U-colloids was observed in the TMA-OH media. However, there is much less uranium colloid formation in TMA-OH tests with low Ca (Na, K) concentration than in previous tests with higher Ca (Na, K) concentrations. This suggests that the colloid formation is promoted by alkali and/or alkali-earth elements.

Hydrothermal synthesis of β-Ni(OH)2 and its supercapacitor properties

Science.gov (United States)

Waghmare, Suraj S.; Patil, Prashant B.; Baruva, Shiva K.; Rajput, Madhuri S.; Deokate, Ramesh J.; Mujawar, Sarfraj H.

2018-04-01

In present manuscript, we synthesized the Nickel hydroxide as an electrode material or supercapacitor application, using hydrothermal method with nickel nitrate as nickel source and hexamethylenetetramine as a directing agent. The reaction was carried out at 160°C temperature for 18 hrs. The structural, morphological and electrochemical characterizations were studied by X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Cyclic Voltammetry (CV) and Galvanostatic Charge Discharge (GCD) respectively. Phase purity and crystalline nature of as prepared nickel hydroxide β-Ni(OH)2 was reveled from X-ray study. Using Debye Scherer's formula crystallite size of ˜15 nm was estimated for Nickel hydroxide. SEM reveals β-platelets like morphology of Ni(OH)2 average of platelets length of the order of 1 µm. Electrochemical studies (CV and GCD) were carried out in 2M KOH electrolyte solution. The maximum capacitance of 225 Fg-1 was observed for scan rate 5 mV within the potential window of 0.1 to 0.4 V.

The electrochemical properties and mechanism of formation of anodic oxide films on Mg-Al alloys

Energy Technology Data Exchange (ETDEWEB)

Kim, Seong Jong; Okido, Masazumi [Nagoya Univ., Nagoya (Japan)

2003-07-01

The electronchemical properties and the mechanism of formation of anodic oxide films on Mg alloys containing 0-15 mass% Al, when anodized in NaOH solution, were investigated by focusing on the effects of anodizing potential, Al content, and anodizing time. The intensity ratio of Mg(OH){sub 2} in the XRD analysis decreased with increasing applied potential, while that of MgO increased. Mg(OH){sub 2} was barely detected at 80 V, while MgO was readily detected. The anti-corrosion properties of anodized specimens at each constant potential were better than those of non-anodized specimens. The specimen anodized at an applied potential of 3 V had the best anti-corrosion property. The intensity ratio of the {beta} phase increased with aluminum content in Mg-Al alloys. During anodizing, the active dissolution reaction occurred preferentially in {beta} phase until about 4 min, and then the current density increased gradually until 7 min. The dissolution reaction progressed in {alpha} phase, which had a lower Al content. In the anodic polarization test in 0.017 mol{center_dot}dm{sup -3} NaCl and 0.1 mol{center_dot}dm{sup -3} Na{sub 2}SO{sub 4} at 298 K, the current density of Mg-15 mass% Al alloy anodized for 10 min increased, since the anodic film that forms on the {alpha} phase is a non-compacted film. The anodic film on the {alpha} phase at 30 min was a compact film as compared with that at 10 min.

Structural, vibrational and morphological properties of layered double hydroxides containing Ni2+, Zn2+, Al3+ and Zr4+ cations

International Nuclear Information System (INIS)

Bezerra, Débora M.; Rodrigues, João E.F.S.; Assaf, Elisabete M.

2017-01-01

Layered double hydroxides are anionic clays with formula [M II 1−x M III x (OH) 2 ] q+ [A n− ] q/n ·mH 2 O, finding possible uses as catalyst support, adsorbents and so on. In this paper, we address the phase formation of layered double hydroxides containing Ni 2+ , Zn 2+ , Al 3+ and Zr 4+ cations, namely, NiZn-Al, NiZn-AlZr and NiZn-Zr compositions obtained by the coprecipitation method. Such systems were characterized by X-ray diffraction, confirming the phase formation for NiZn-Al and NiZn-AlZr samples. Infrared and Raman spectroscopies elucidated the anion and water molecules occurrence in the interlayer. Nitrogen physisorption (BET method) determined the presence of pores and specific surface area. The isotherm shapes were Type IV, according to the IUPAC, and represent a mesoporous structure. A morphological study was performed by means of scanning and transmission electron microscopies, and particle size values of 120, 131 and 235 nm for NiZn-Al, NiZn-AlZr and NiZn-Zr, respectively, were determined. Thermogravimetric analysis of the decomposition of the systems revealed that their complete disintegration occurred at ~ 450 °C and resulted in mixed oxides.

Electrochemical corrosion behaviour of lead-free Sn-8.5 Zn-X Ag-0.1 Al-0.5 Ga solder in 3.5% NaCl solution

International Nuclear Information System (INIS)

Mohanty, Udit Surya; Lin, K.-L.

2005-01-01

The electrochemical corrosion behaviour of Pb-free Sn-8.5 Zn-X Ag-0.1 Al-0.5 Ga solder in 3.5% NaCl solution was investigated by using potentiodynamic polarization methods, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and X-ray photoelectron spectroscopy (XPS) analysis. The results obtained from polarization studies showed that an increase in the Ag content from 0.1 to 1.5 wt% decreased the corrosion current density (I corr ) and shifted the corrosion potential (E corr ) towards more noble values. These changes were also reflected in the linear polarization resistance (LPR), corrosion rate, anodic Tafel slope (b A ) and the cathodic Tafel slope (b c ) values, respectively. Passivation behaviour was noted in the Sn-Zn-X Ag-Al-Ga solders with Ag content > 0.1 wt%. The oxides and hydroxides of zinc were responsible for the formation of passive film. Presence of Ag atoms in the oxide layer also improved the passivation behaviour of solders to a certain extent. X-ray photoelectron spectroscopy revealed that two different oxygen species were formed on the surface films, one was assigned to OH - in Zn(OH) 2 and the other to O 2 - in ZnO. XPS depth profile results revealed that the two species had different depth distribution in the films. SEM and EDX analyses confirmed SnCl 2 as the major corrosion product formed after the electrochemical experiments

Topologically identical, but geometrically isomeric layers in hydrous α-, β-Rb[UO{sub 2}(AsO{sub 3}OH)(AsO{sub 2}(OH){sub 2})]·H{sub 2}O and anhydrous Rb[UO{sub 2}(AsO{sub 3}OH)(AsO{sub 2}(OH){sub 2})

Energy Technology Data Exchange (ETDEWEB)

Yu, Na; Klepov, Vladislav V. [Forschungszentrum Jülich GmbH, Institute for Energy and Climate Research (IEK-6), 52428 Jülich (Germany); Villa, Eric M. [Department of Chemistry, Creighton University, 2500 California Plaza, Omaha NE 68178 (United States); Bosbach, Dirk [Forschungszentrum Jülich GmbH, Institute for Energy and Climate Research (IEK-6), 52428 Jülich (Germany); Suleimanov, Evgeny V. [Department of Chemistry, Lobachevsky State University of Nizhny Novgorod, 603950 Nizhny Novgorod (Russian Federation); Depmeier, Wulf [Institut für Geowissenschaften, Universität zu Kiel, 24118 Kiel (Germany); Albrecht-Schmitt, Thomas E., E-mail: albrecht-schmitt@chem.fsu.edu [Department of Chemistry and Biochemistry, Florida State University, 102 Varsity Way, Tallahassee, FL 32306-4390 (United States); Alekseev, Evgeny V., E-mail: e.alekseev@fz-juelich.de [Forschungszentrum Jülich GmbH, Institute for Energy and Climate Research (IEK-6), 52428 Jülich (Germany); Institut für Kristallographie, RWTH Aachen University, 52066 Aachen (Germany)

2014-07-01

The hydrothermal reaction of uranyl nitrate with rubidium nitrate and arsenic (III) oxide results in the formation of polymorphic α- and β-Rb[UO{sub 2}(AsO{sub 3}OH)(AsO{sub 2}(OH){sub 2})]·H{sub 2}O (α-, β-RbUAs) and the anhydrous phase Rb[UO{sub 2}(AsO{sub 3}OH)(AsO{sub 2}(OH){sub 2})] (RbUAs). These phases were structurally, chemically and spectroscopically characterized. The structures of all three compounds are based upon topologically identical, but geometrically isomeric layers. The layers are linked with each other by means of the Rb cations and hydrogen bonding. Dehydration experiments demonstrate that water deintercalation from hydrous α- and β-RbUAs yields anhydrous RbUAs via topotactic reactions. - Graphical abstract: Three different layer geometries observed in the structures of Rb[UO{sub 2}(AsO{sub 3}OH)(AsO{sub 2}(OH){sub 2})] and α- and β- Rb[UO{sub 2}(AsO{sub 3}OH)(AsO{sub 2}(OH){sub 2})]·H{sub 2}O. Two different coordination environments of uranium polyhedra (types I and II) are shown schematically on the top of the figure. - Highlights: • Three new uranyl arsenates were synthesized from the hydrothermal reactions. • The phases consist of the topologically identical but geometrically different layers. • Topotactic transitions were observed in the processes of mono-hyrates dehydration.

Enhanced supercapacitor performance using hierarchical TiO2 nanorod/Co(OH)2 nanowall array electrodes

International Nuclear Information System (INIS)

Ramadoss, Ananthakumar; Kim, Sang Jae

2014-01-01

Graphical abstract: - Highlights: • TiO 2 /Co(OH) 2 hierarchical nanostructure was prepared by a combination of hydrothermal and cathodic electrodeposition method. • Hierarchical nanostructure electrode exhibited a maximum capacitance of 274.3 mF cm −2 at a scan rate of 5 mV s −1 . • Combination of Co(OH) 2 nanowall with TiO 2 NR into a single system enhanced the electrochemical behavior of supercapacitor electrode. - Abstract: We report novel hierarchical TiO 2 nanorod (NR)/porous Co(OH) 2 nanowall array electrodes for high-performance supercapacitors fabricated using a two-step process that involves hydrothermal and electrodeposition techniques. Field-emission scanning electron microscope images reveal a bilayer structure consisting of TiO 2 NR arrays with porous Co(OH) 2 nanowalls. Compared with the bare TiO 2 NRs, the hierarchical TiO 2 NRs/Co(OH) 2 electrodes showed improved pseudocapacitive performance in a 2-M KOH electrolyte solution, exhibiting an areal specific capacitance of 274.3 mF cm −2 at a scan rate of 5 mV s −1 . The electrodes exhibited good stability, retaining 82.5% of the initial capacitance after 4000 cycles. The good pseudocapacitive performance of the hierarchical nanostructures is mainly due to the porous structure, which provides fast ion and electron transfer, a large surface area, short ion diffusion paths, and a favourable volume change during the cycling process

Characterization of corrosion products of Zn and Zn–Mg–Al coated steel in a marine atmosphere

International Nuclear Information System (INIS)

Diler, E.; Rouvellou, B.; Rioual, S.; Lescop, B.; Nguyen Vien, G.; Thierry, D.

2014-01-01

Highlights: • The corrosion behaviour of Zn–Mg–Al alloy in marine environment is characterized. • Zn–Mg–Al alloy shows a better corrosion resistance than Zn. • Strong enhancement of NaZn 4 Cl(OH) 6 SO 4 ·6H 2 O in the corrosion products is observed. • Al 3+ and Mg 2+ induced quenching effects in corrosion activity are described. - Abstract: The corrosion behaviour of pure zinc and zinc–magnesium–aluminium alloy (ZMA) has been studied during 6 months of exposure in marine environment (Brest, France). The composition of corrosion products is analysed using infrared spectroscopy (FTIR), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). An improved corrosion resistance of ZMA is observed. This improvement is found to be connected to Mg 2+ and Al 3+ induced quenching of corrosion activity and to the enhancement of NaZn 4 Cl(OH) 6 SO 4 ·6H 2 O in the formed corrosion product

EXAFS Characterization of Dendrimer-Derived Pt/γ-Al2O3

International Nuclear Information System (INIS)

Siani, A.; Alexeev, O. S.; Williams, C. T.; Ploehn, H. J.; Amiridis, M. D.

2007-01-01

The various steps involved in the preparation of a Pt/γ-Al2O3 material using hydroxyl-terminated generation four (G4OH) PAMAM dendrimers as templates were monitored by EXAFS. The results indicate that Cl ligands in the Pt precursors (H2PtCl6 and K2PtCl4) were partially replaced by aquo ligands upon hydrolysis to form [PtCl3(H2O)3]+ and [PtCl2(H2O)2] species. After interaction of such species with G4OH, Cl ligands from the first coordination shell of Pt were further replaced by nitrogen atoms from the dendrimer interior, indicating the complexation of Pt with the dendrimer. This process was accompanied by a transfer of the electron density from the dendrimer to Pt, indicating that the former plays the role of a ligand. Following treatment of the H2PtCl6/G4OH and K2PtCl4/G4OH composites with NaBH4, no substantial changes were detecteded in the electronic or coordination environment of Pt, and no formation of metal nanoparticles was observed. However, when the reduction treatment was performed with H2, the formation of extremely small Pt clusters incorporating no more than 4 Pt atoms was observed. These Pt species remained strongly bonded to the dendrimer and their nuclearity depends on the length of the H2 treatment. Formation of Pt nanoparticles with an average diameter of approximately 10 A was finally observed after the deposition of H2PtCl6/G4OH on γ-Al2O3 and drying, suggesting that their formation may be related to the collapse of the dendrimer structure. The Pt nanoparticles formed appear to have high mobility, since subsequent thermal treatment in O2/H2 led to further sintering

Fabrication and properties of highly luminescent materials from Tb(OH)3-SiO2 and Tb(OH)3-SiO2:Eu3+ nanotubes

International Nuclear Information System (INIS)

Tran Thu Huong; Tran Kim Anh; Le Quoc Minh

2009-01-01

Luminescent nanomaterials with one-dimensional (1D) structures have attracted much attention due to their unique properties and potential applications in nanophotonics and nanobiophotonics. In this paper, we report a synthesis of terbium - hydroxide - at - silica Tb(OH) 3 -SiO 2 and Tb(OH) 3 -SiO 2 :Eu 3+ nanotubes. Terbium - hydroxide tubes were synthesized by soft template method. The size of the tubes can be controlled precisely and have outer diameters ranging from 80 to 120 nm, wall thickness of about 30 nm, and lengths ranging from 300 to 800 nm. To fabricate core/shell materials, the seed growth method is used. FESEM, X-ray diffraction, Raman spectra of Tb(OH) 3 and Tb(OH) 3 -SiO 2 nanotubes were investigated. The photoluminescence (PL) spectrum of Tb(OH) 3 under 325 nm excitation consists of four main peaks at 488, 542, 582, and 618 nm. Furthermore, a preliminary suggestion for the mechanism of growth of the Tb(OH) 3 nanotubes using the soft - template synthesis technique has been proposed. The PL intensity from Tb(OH) 3 -SiO 2 or Tb(OH) 3 -SiO 2 :Eu 3+ nanotubes is much stronger than that of Tb(OH) 3 .

Contributions of primary and secondary biogenic VOC tototal OH reactivity during the CABINEX (Community Atmosphere-Biosphere INteractions Experiments-09 field campaign

Directory of Open Access Journals (Sweden)

S. Kim

2011-08-01

indicates that the ratio of OH reactivity from unmeasured products over OH reactivity from MVK + MACR is strongly dependent on NO concentrations. The unmeasured oxidation products can contribute ~7.2 % (8.8 % from LIM and 5.6 % by MIM 2 when NO = 100 pptv of the isoprene contribution towards total ambient OH reactivity. This amount can explain ~8.0 % (9.7 % from LIM and 6.2 % from MIM 2 of missing OH reactivity, reported by Di Carlo et al. (2004 at the same site. Further study on the contribution from further generation of unmeasured oxidation products is needed to constrain tropospheric photochemical reactivity of BVOC that have important implications for both photochemical ozone and secondary organic aerosol formation.

Synthesis of Co-Al-Cl LDH by cathodic material reprocessing from cellular phone batteries

Energy Technology Data Exchange (ETDEWEB)

Amaral, Fabio Augusto do; Machado, Erica Oliveira; Freitas, Leonardo Luis de; Santana, Laiane Kalita; Canobre, Sheila Cristina, E-mail: fabioamaral@yahoo.com.br, E-mail: fabioamaral@iqufu.ufu.br [Universidade Federal de Uberlandia (UFU/LAETE), (Brazil). Inst. de Quimica. Lab. de Armazenamento de Energia e Tratamento de Efluente

2014-08-15

The aim of this paper was the recovering of the cathodic material from discarded lithium ion batteries for obtainment of the lamellar double hydroxides (LDHs) by the co-precipitation method at variable pH in HCl and H{sub 2}O{sub 2} 1:1 (v/v) acid solution containing Co and Al (extracted from cathodic material composed of LiCoO{sub 2} and aluminum foil). These metals were precipitated in LiOH at pH 9 or 11, or NH{sub 4}OH at pH 9 and submitted to the hydrothermal treatment (HT) to improve the structural organization of the LDHs lamellae. After precipitation, the resulting solids were structurally characterized by XRD for phase identification and calculation of the unit cell parameter, thermally by TGA for the identification of the mass loss and morphologically by SEM. The sample obtained by precipitation with LiOH at pH 11 / hydrothermal treatment showed diffraction peaks similar to hydrotalcite, morphological and thermal characteristics similar to the pattern Co-Al-Cl LDH obtained by co-precipitation at constant pH 8. (author)

A highly sensitive, single selective, fluorescent sensor for Al3+ detection and its application in living cell imaging

International Nuclear Information System (INIS)

Ye, Xing-Pei; Sun, Shao-bo; Li, Ying-dong; Zhi, Li-hua; Wu, Wei-na; Wang, Yuan

2014-01-01

A new o-aminophenol-based fluorogenic chemosensor methyl 3,5-bis((E)-(2-hydroxyphenylimino)methyl)-4-hydroxybenzoate 1 have been synthesized by Schiff base condensation of methyl 3,5-diformyl-4-hydroxybenzoate with o-aminophenol, which exhibits high selectivity and sensitivity toward Al 3+ . Fluorescence titration studies of receptors 1 with different metal cations in CH 3 OH medium showed highly selective and sensitive towards Al 3+ ions even in the presence of other commonly coexisting metal ions. The detection limit of Al 3+ ions is at the parts per billion level. Interestingly, the Al(III) complex of 1 offered a large Stokes shift (>120 nm), which can miximize the selfquenching effect. In addition, possible utilization of this receptor as bio-imaging fluorescent probe to detect Al 3+ in human cervical HeLa cancer cell lines was also investigated by confocal fluorescence microscopy. - Highlights: • A new Schiff base chemosensor is reported. • The sensor for Al 3+ offers large Stokes shift. • The detection limit of Al 3+ in CH 3 OH solution is at the parts per billion level. • The utilization of sensor for the monitoring of Al 3+ levels in living cells was examined

Dehydration of δ-AlOOH in the lower mantle

Science.gov (United States)

Piet, H.; Shim, S. H.; Tappan, J.; Leinenweber, K. D.; Greenberg, E.; Prakapenka, V. B.

2017-12-01

Hydrous phase δ-AlOOH is an important candidate for water transport and storage in the Earth's deep mantle [1]. Knowing the conditions, under which it is stable and dehydrated, is therefore important for understanding the water transportation to the deep mantle or even to the core. A few experimental studies [1, 2] have shown that δ-AlOOH may be stable in cold descending slabs while it is dehydrated into a mixture of corundum and water under normal mantle conditions, up to 25 GPa. A subsequent study [3] reported the stability of δ-AlOOH in cold descending slabs to the core-mantle boundary conditions (2300 K at 135 GPa). However, the dehydration of δ-AlOOH has not bee directly observed in the experiments conducted at pressures above 25 GPa. We have synthesized δ-AlOOH from diaspore and Al(OH)3 in multi-anvil press at ASU. The sample was mixed with Au for coupling with near IR laser beams and loaded in diamond-anvil cells. We performed the laser-heated diamond anvil cell experiments at the 13IDD beamline of the Advanced Photon Source and ASU. At APS, we measured X-ray diffraction patterns at in situ high pressure and temperature. We observed the appearance of the corundum diffraction lines at 1700-2000 K and 55-90 GPa, indicating the dehydration of δ-AlOOH to Al2O3+ H2O. We found that the transition occurs over a broad range of temperature (500 K). We also observed that the dehydration of δ-AlOOH was accompanied by sudden change in laser coupling, most likely due to the release of fluids. The property change also helps us to determine the dehydration at ASU without in situ XRD. Our new experimental results indicate that δ-AlOOH would be stable in most subducting slabs in the deep mantle. However, because the dehydration occurs very close to the temperatures expected for the lower mantle, its stability is uncertain in the normal mantle. [1] Ohtani et al. 2001, Stability field of new hydrous phase, delta-AlOOH, Geophysical Research Letters 28, 3991-3993. [2

Mechanisms of charge transfer and redistribution in LaAlO3/SrTiO3 revealed by high-energy optical conductivity.

Science.gov (United States)

Asmara, T C; Annadi, A; Santoso, I; Gogoi, P K; Kotlov, A; Omer, H M; Motapothula, M; Breese, M B H; Rübhausen, M; Venkatesan, T; Ariando; Rusydi, A

2014-04-14

In condensed matter physics the quasi two-dimensional electron gas at the interface of two different insulators, polar LaAlO3 on nonpolar SrTiO3 (LaAlO3/SrTiO3) is a spectacular and surprising observation. This phenomenon is LaAlO3 film thickness dependent and may be explained by the polarization catastrophe model, in which a charge transfer of 0.5e(-) from the LaAlO3 film into the LaAlO3/SrTiO3 interface is expected. Here we show that in conducting samples (≥ 4 unit cells of LaAlO3) there is indeed a ~0.5e(-) transfer from LaAlO3 into the LaAlO3/SrTiO3 interface by studying the optical conductivity in a broad energy range (0.5-35 eV). Surprisingly, in insulating samples (≤ 3 unit cells of LaAlO3) a redistribution of charges within the polar LaAlO3 sublayers (from AlO2 to LaO) as large as ~0.5e(-) is observed, with no charge transfer into the interface. Hence, our results reveal the different mechanisms for the polarization catastrophe compensation in insulating and conducting LaAlO3/SrTiO3 interfaces.

Broad photoelectron spectrum and lowered electron affinity due to hydrogen in ZnOH: A joint experimental and theoretical study

Science.gov (United States)

Iordanov, I.; Gunaratne, K. D. D.; Harmon, C. L.; Sofo, J. O.; Castleman, A. W.

2012-06-01

We report a combined experimental and theoretical photoelectron spectroscopy study of ZnOH-. We find that the electron binding energy spectrum of ZnOH- reveals a broad and featureless peak between 1.4 and 2.4 eV in energy. The vertical detachment energy (VDE) of ZnOH- is determined to be 1.78 eV, which is lower than the 2.08 eV VDE of ZnO-. Our theoretical calculations match the VDE of ZnOH- accurately, but we find that the broadness of the peak cannot be explained by rotational or vibrational state excitation. The broadness of this peak is in strong contrast to the narrow and easily understood first peak of the ZnO spectrum, which features a well-resolved vibrational progression that can be readily explained by calculating the Franck-Condon transition factors. This study provides spectroscopic evidence of the effect of hydrogen on diatomic ZnO.

Quadrupole hyperfine structure and splitting of Δ-levels in the microwave spectra of KOH, RbOH and CsOH in the 100 GHz region

International Nuclear Information System (INIS)

Kuijpers, P.; Dymanus, A.; Toerring, T.

1977-01-01

Hyperfine structure of rotational transitions of KOH, RbOH and CsOH in various v 2 - and l-states has been carefully measured in the 100 GHz range. From the observed splittings and broadenings information about quadrupole coupling constant (eqQ) of the K nucleus in KOH and about the spacing (Esub(Δ) - Esub(Σ)) between Σ and Δ levels in the vibrational spectrum of KOH, RbOH and CsOH has been derived. The measured value of the eqQ of KOH is close to that of KF. The separation between Σ and Δ levels is found to be rather similar for the group of the alkali hydroxides increasing gradually when progressing from LiOH to CsOH. (orig.) [de

Microwave assisted rapid growth of Mg(OH){sub 2} nanosheet networks for ethanol chemical sensor application

Energy Technology Data Exchange (ETDEWEB)

Al-Hazmi, Faten [Department of Physics, College of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21569 (Saudi Arabia); Umar, Ahmad, E-mail: ahmadumar786@gmail.com [Promising Centre for Sensors and Electronic Devices (PCSED) and Centre for Advanced Materials and Nano-Research (CAMNR), Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Dar, G.N. [Promising Centre for Sensors and Electronic Devices (PCSED) and Centre for Advanced Materials and Nano-Research (CAMNR), Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Al-Ghamdi, A.A.; Al-Sayari, S.A. [Department of Physics, College of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21569 (Saudi Arabia); Al-Hajry, A. [Promising Centre for Sensors and Electronic Devices (PCSED) and Centre for Advanced Materials and Nano-Research (CAMNR), Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Department of Physics, College of Science and Arts, Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Kim, S.H. [Promising Centre for Sensors and Electronic Devices (PCSED) and Centre for Advanced Materials and Nano-Research (CAMNR), Najran University, P.O. Box 1988, Najran 11001 (Saudi Arabia); Al-Tuwirqi, Reem M. [Department of Physics, College of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21569 (Saudi Arabia); Alnowaiserb, Fowzia [Department of Chemistry, Faculty of Science, King Abdulaziz University, Jeddah (Saudi Arabia); El-Tantawy, Farid [Department of Physics, Faculty of Science, Suez Canal University, Ismailia (Egypt)

2012-04-05

Highlights: Black-Right-Pointing-Pointer A facile microwave-assisted synthesis and characterizations of magnesium hydroxide (Mg(OH){sub 2}) nanosheet networks. Black-Right-Pointing-Pointer Fabrication of ethanol sensor based on (Mg(OH){sub 2}) nanosheet networks. Black-Right-Pointing-Pointer Good sensitivity ({approx}3.991 {mu}A cm{sup -2} mM{sup -1}) and lower detection limit (5 {mu}M). Black-Right-Pointing-Pointer This research opens a way to utilize Mg(OH){sub 2} nanostructures for chemical sensors applications. - Abstract: This paper reports a facile microwave-assisted synthesis of magnesium hydroxide (Mg(OH){sub 2}) nanosheet networks and their utilization for the fabrication of efficient ethanol chemical sensor. The synthesized nanosheets networks were characterized in terms of their morphological, structural and optical properties using various analysis techniques such as field emission scanning electron microscopy (FESEM), X-ray diffraction pattern (XRD), Fourier transform infrared (FTIR) and UV-Vis spectroscopy. The detailed morphological and structural investigations reveal that the synthesized (Mg(OH){sub 2}) products are nanosheet networks, grown in high density, and possessing hexagonal crystal structure. The optical band gap of as-synthesized Mg(OH){sub 2} nanosheet networks was examined by UV-Vis absorption spectrum, and found to be 5.76 eV. The synthesized nanosheet networks were used as supporting matrices for the fabrication of I-V technique based efficient ethanol chemical sensor. The fabricated ethanol sensor based on nanosheet networks exhibits good sensitivity ({approx}3.991 {mu}A cm{sup -2} mM{sup -1}) and lower detection limit (5 {mu}M), with linearity (R = 0.9925) in short response time (10.0 s). This work demonstrate that the simply synthesized Mg(OH){sub 2} nanosheet networks can effectively be used for the fabrication of efficient ethanol chemical sensors.

Methane coupling reaction in an oxy-steam stream through an OH radical pathway by using supported alkali metal catalysts

KAUST Repository

Liang, Yin

2014-03-24

A universal reaction mechanism involved in the oxidative coupling of methane (OCM) is demonstrated under oxy-steam conditions using alkali-metal-based catalysts. Rigorous kinetic measurements indicated a reaction mechanism that is consistent with OH radical formation from a H 2O-O2 reaction followed by C-H activation in CH 4 with an OH radical. Thus, the presence of water enhances both the CH4 conversion rate and the C2 selectivity. This OH radical pathway that is selective for the OCM was observed for the catalyst without Mn, which suggests clearly that Mn is not the essential component in a selective OCM catalyst. The experiments with different catalyst compositions revealed that the OH.-mediated pathway proceeded in the presence of catalysts with different alkali metals (Na, K) and different oxo anions (W, Mo). This difference in catalytic activity for OH radical generation accounts for the different OCM selectivities. As a result, a high C2 yield is achievable by using Na2WO4/SiO2, which catalyzes the OH.-mediated pathway selectively. Make it methane: A universal reaction mechanism involved in the oxidative coupling of methane is demonstrated under oxy-stream conditions by using alkali-metal-based catalysts. Rigorous kinetic measurements indicated a reaction mechanism that is consistent with OH radical formation from an H2O-O2 reaction, followed by C-H activation in CH4 with an OH radical. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Investigation of Mg(OH)2 nanoparticles as an antibacterial agent

International Nuclear Information System (INIS)

Dong Chunxu; Cairney, John; Sun Qunhui; Maddan, Orville Lee; He Gaohong; Deng Yulin

2010-01-01

Our experimental results of using Mg(OH) 2 nanoparticles as an antibacterial agent are reported in this study. The antibacterial behavior of Mg(OH) 2 nanoparticles in liquid culture and in paper sheets was investigated. The colony forming units (CFU) counting and the headspace gas chromatography (HS-GC) measurement were used to determine the cell viability. Results indicate that Mg(OH) 2 nanoparticles are effective antibacterial agent against Escherichia coli (E. coli) and Burkholderia phytofirmans, and the OH - and Mg 2+ ions in Mg(OH) 2 water suspension were found not to be the reason for killing the bacteria. Mg(OH) 2 nanoparticles could be added directly to wood pulp to make paper sheets, whose antibacterial efficiency increased with the increase of the nanoparticle amount. The possible mechanism of antibacterial effect of Mg(OH) 2 nanoparticles is discussed.

Direct observation of OH production from the ozonolysis of olefins

Science.gov (United States)

Donahue, Neil M.; Kroll, Jesse H.; Anderson, James G.; Demerjian, Kenneth L.

Ozone olefin reactions may be a significant source of OH in the urban atmosphere, but current evidence for OH production is indirect and contested. We report the first direct observation of OH radicals from the reaction of ozone with a series of olefins (ethene, isoprene, trans-2-butene and 2,3 dimethyl-2-butene) in 4-6 torr of nitrogen. Using LIF to directly observe the steady-state of OH produced by the initial ozone-olefin reaction and subsequently destroyed by the OH-olefin reaction, we are able to establish OH yields broadly consistent with indirect values. The identification of the OH is unequivocal, and there is no indication that it is produced by a secondary process. To support these observations, we present a complete ab-initio potential energy surface for the O3-ethene reaction, extending from the reactants to available products.

Dissolution of targets for the production of Mo-99: Part 1. Influence of NaOH concentration and the addition of NaNO{sub 3} and NaNO{sub 2} on the dissolution time

Energy Technology Data Exchange (ETDEWEB)

Camilo, Ruth L.; Araujo, Izilda da C.; Mindrisz, Ana C.; Forbicini, Christina A.L.G. de O., E-mail: rcamilo@ipen.br, E-mail: icaraujo@ipen.br, E-mail: acmindri@ipen.br, E-mail: cforbici@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN/SP), Sao Paulo, SP (Brazil)

2011-07-01

Faced with global crisis in the production of radioisotope {sup 99}Mo, which product of decay, {sup 99}mTc, is the tracer element most often used in nuclear medicine and accounts for about 80% of all diagnostic procedures in vivo, since September 2008 Brazil is developing the project called Brazilian Multipurpose Reactor (RMB). Within the Brazilian Nuclear Program (PNB) the construction of the RMB, is seen as a long term solution to meet all domestic demand relative to the supply of radioisotopes and radiopharmaceuticals. In the process to be studied to obtain {sup 99}Mo from irradiated UA1{sub x}-A1 LEU targets employing alkaline dissolution, processing time should be minimized, considering the short half life of {sup 99}Mo and {sup 99}mTc, about 66 h and 6 h, respectively. That makes dissolution time a significant factor in the development of the process. This paper presents the results of alkaline dissolution of scraps of Al, used to simulate the dissolution process of UA1{sub x}-A1 targets. Al corresponds to about 79% of the total weight of the UA1{sub x}-A1 target. The effect of NaOH concentration on dissolution time for the interval of 1 to 3.5 mol.L-1 was studied, keeping the molar ratio in 1Al:2.16NaOH and the initial temperature of 88 degree C. The influence of reagent composition over dissolution time was studied using three different solutions: a) 3 mol.L{sup -1} NaOH, b) 3 mol.L{sup -1} NaOH/NaNO{sub 3} and c) 3 mol.L{sup -1} NaOH/NaNO{sub 2}, keeping the same molar ratio and temperature. The results showed that the dissolution time decreases with increasing NaOH concentration and the addition of NaNO{sub 3} or NaNO{sub 2} in the NaOH solution reduces both dissolution time and volume of gases released. (author)

Effects of optical diagnostic techniques on the accuracy of laminar flame speeds measured from Bunsen flames: OH* chemiluminescence, OH-PLIF and acetone/kerosene-PLIF

Science.gov (United States)

Wu, Yi; Modica, Vincent; Yu, Xilong; Li, Fei; Grisch, Frédéric

2018-01-01

The effects of optical diagnostic techniques on the accuracy of laminar flame speed measured from Bunsen flames were investigated. Laminar flame speed measurements were conducted for different fuel/air mixtures including CH4/air, acetone/air and kerosene (Jet A-1)/air in applying different optical diagnostic techniques, i.e. OH* chemiluminescence, OH-PLIF and acetone/kerosene-PLIF. It is found that the OH* chemiluminescence imaging technique cannot directly derive the location of the outer edge of the fresh gases and it is necessary to correct the position of the OH* peak to guarantee the accuracy of the measurements. OH-PLIF and acetone/kerosene-PLIF respectively are able to measure the disappearance of the fresh gas contour and the appearance of the reaction zone. It shows that the aromatic-PLIF technique gives similar laminar flame speed values when compared with those obtained from corrected OH* chemiluminescence images. However, discrepancies were observed between the OH-PLIF and the aromatic-PLIF techniques, in that OH-PLIF slightly underestimates laminar flame speeds by up to 5%. The difference between the flame contours obtained from different optical techniques are further analysed and illustrated with 1D flame structure simulation using detailed kinetic mechanisms.

Natural Rosin-based Phosphate Diester Surfactant Assisted One-step Synthesis of 3D Flowerlikeβ-Ni(OH)2/γ-Ni(OH)2 Composite Nano-microspheres

Institute of Scientific and Technical Information of China (English)

BoShi Wu; Juan Li; ChunRui Han; Feng Xu

2018-01-01

Self-assembled uniform 3Dflowerlikeβ-Ni(OH)2/g-Ni(OH)2composite nano-microspheres with hollow interiors were successfully synthesized via a facile aqueous-ethanol mixed solvothermal method, using nickel sulfate as a precursor, urea as a precipitant, and dehydroabietic based phosphate diester sodium (DDPDS) as a surfactant. The prepared 3D flowerlikeβ-Ni(OH)2/g-Ni(OH)2composite nano-microspheres were tested as supercapacitors in a two-electrode cell with 6 mol/L KOH electrolyte. In addition, the influence of DDPDS concentration on the morphology and size of 3Dflowerlikeβ-Ni(OH)2/g-Ni(OH)2composite nano-microspheres was studied at 180℃. X-ray diffraction (XRD), scanning electron microscopy (SEM), BET(Brunauer, Emmett and Teller)techniques, and equity default swap (EDS) were used to characterize the structure, morphology, and size of the as-prepared samples. Moreover, a possible formation mechanism of the 3Dflowerlikeβ-Ni(OH)2/g-Ni(OH)2composite nano-microspheres was proposed based on the effects of DDPDS concentrationand reaction time. The surfactant micelles were used as soft templates to induce the self-assembly of nanosheets. The crystallinity of the 3D flowerlikeβ-Ni(OH)2/g-Ni(OH)2composite nano-microspheres improved with the increase of DDPDS concentration, and the morphology and size of synthetic nano-microspheres could be controlled.

1α,25(OH)2D3 differentially regulates miRNA expression in human bladder cancer cells.

Science.gov (United States)

Ma, Yingyu; Hu, Qiang; Luo, Wei; Pratt, Rachel N; Glenn, Sean T; Liu, Song; Trump, Donald L; Johnson, Candace S

2015-04-01

Bladder cancer is the fourth most commonly diagnosed cancer in men and eighth leading cause of cancer-related death in the US. Epidemiological and experimental studies strongly suggest a role for 1α,25(OH)2D3 in cancer prevention and treatment. The antitumor activities of 1α,25(OH)2D3 are mediated by the induction of cell cycle arrest, apoptosis, differentiation and the inhibition of angiogenesis and metastasis. miRNAs play important regulatory roles in cancer development and progression. However, the role of 1α,25(OH)2D3 in the regulation of miRNA expression and the potential impact in bladder cancer has not been investigated. Therefore, we studied 1α,25(OH)2D3-regulated miRNA expression profiles in human bladder cancer cell line 253J and the highly tumorigenic and metastatic derivative line 253J-BV by miRNA qPCR panels. 253J and 253J-BV cells express endogenous vitamin D receptor (VDR), which can be further induced by 1α,25(OH)2D3. VDR target gene 24-hydroxylase was induced by 1α,25(OH)2D3 in both cell lines, indicating functional 1α,25(OH)2D3 signaling. The miRNA qPCR panel assay results showed that 253J and 253J-BV cells have distinct miRNA expression profiles. Further, 1α,25(OH)2D3 differentially regulated miRNA expression profiles in 253J and 253J-BV cells in a dynamic manner. Pathway analysis of the miRNA target genes revealed distinct patterns of contribution to the molecular functions and biological processes in the two cell lines. In conclusion, 1α,25(OH)2D3 differentially regulates the expression of miRNAs, which may contribute to distinct biological functions, in human bladder 253J and 253J-BV cells. This article is part of a Special Issue entitled '17th Vitamin D Workshop'. Copyright © 2014 Elsevier Ltd. All rights reserved.

Heterogeneous processing of biomass burning aerosol proxies by OH radicals for a wide range of OH concentrations and detection of volatilization products

Science.gov (United States)

Slade, J. H.; Knopf, D. A.

2012-12-01

Biomass burning aerosol (BBA) constitutes the majority of primary organic aerosol found in the atmosphere, with emission rates comparable to fossil-fuel burning. BBA affects earth's radiative budget directly through absorption and scattering of radiation or indirectly by modifying cloud radiative properties, and impacts air quality. Quantifying BBA source strength and thus its effects on air quality, human health, and climate can be difficult since these organic particles can chemically transform during atmospheric transport, a process also termed aging, due to heterogeneous reactions with oxidants and radicals such as OH. In this work we investigate the reactive uptake of OH radicals by typical BBA compounds that also serve as molecular markers for source apportionment studies. Organic substrates of cellulose pyrolysis products such as levoglucosan (1,6-anhydro-β-glucopyranose, C6H10O5), resin acids such as abietic acid (1-phenanthrenecarboxylic acid, C20H30O2), and lignin decomposition products such as 5-nitroguaiacol (2-methoxy-5-nitrophenol, C7H7NO4) have been exposed to a wide range of OH concentrations (~107-1011 cm-3), in presence of O2 in a rotating wall flow reactor operated at 2-6 mbar coupled to a custom built chemical ionization mass spectrometer (CIMS). OH radicals were generated through H2 dissociation in an Evenson microwave resonant cavity operated at 2.45 GHz followed by reaction with O2 or NO2. In addition, potential volatilization of organic material due to heterogeneous oxidation by OH has been determined in-situ by monitoring the volatile organic compounds using a high resolution-proton transfer reaction-time of flight-mass spectrometer (HR-PTR-ToF-MS). The volatilization studies are conducted at 1 atm and OH is generated by O3 photolysis in the presence of H2O vapor and quantified using a photochemical box model as well as through reaction with a known concentration of isoprene (2-methyl-1,3-butadiene, C5H8). Reactive uptake validation

Precursor preparation for Ca-Al layered double hydroxide to remove hexavalent chromium coexisting with calcium and magnesium chlorides

Energy Technology Data Exchange (ETDEWEB)

Zhong, Lihua; He, Xiaoman; Qu, Jun; Li, Xuewei; Lei, Zhiwu; Zhang, Qiwu [School of Resources and Environment Engineering, Wuhan University of Technology, Wuhan 430070 (China); Liu, Xinzhong [College of Ecological Environment and Urban Construction, Fujian University of Technology, Fuzhou 350118 (China)

2017-01-15

Al(OH){sub 3} and Ca(OH){sub 2} powders are co-ground to prepare a precursor which hydrates into a layered double hydroxide (LDH) phase by agitation in aqueous solution with target hexavalent chromium (Cr(VI)) at room temperature, to achieve an obvious improvement in removal efficiency of Cr(VI) through an easy incorporation into the structure. Although the prepared precursor transforms into LDH phases also when agitated in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist. The adsorption isotherm and kinetic studies show that the phenomena occurring on the Al-Ca precursor fit a pseudo-second-order kinetics with a Langmuir adsorption capacity of 59.45 mg/g. Besides, characterizations of the prepared precursor and the samples after adsorption are also performed by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Transmission electron microscope (TEM) to understand the reason of the preferential incorporation of Cr(VI) to the coexisting chloride salts during the LDH phase formation. - Graphical abstract: Activated Ca-Al hydroxides (C{sub 3}A) transformed into Ca-Al-OH compound when agitated in water. Ca-Al precursor (C{sub 3}A) was agitated in a hexavalent chromium (Cr(VI)) solution to form Al-Ca-CrO{sub 4} LDH product. Ca-Al-CrO{sub 4} LDH phase occurred preferentially to Ca-Al-MCl{sub 2} LDH phases in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist. - Highlights: • Activated Ca-Al hydroxides transformed into LDH when agitated in water with some inorganic substances. • Hexavalent Cr was incorporated in the LDH structure at high adsorption capacity. • Ca-Al-Cr LDH phase occurred preferentially to Ca-Al-MCl{sub 2} LDH phases with coexistence. • The prepared Ca-Al hydroxides had high performance as adsorbent even with high salinity of the solution.

Precursor preparation for Ca-Al layered double hydroxide to remove hexavalent chromium coexisting with calcium and magnesium chlorides

International Nuclear Information System (INIS)

Zhong, Lihua; He, Xiaoman; Qu, Jun; Li, Xuewei; Lei, Zhiwu; Zhang, Qiwu; Liu, Xinzhong

2017-01-01

Al(OH) 3 and Ca(OH) 2 powders are co-ground to prepare a precursor which hydrates into a layered double hydroxide (LDH) phase by agitation in aqueous solution with target hexavalent chromium (Cr(VI)) at room temperature, to achieve an obvious improvement in removal efficiency of Cr(VI) through an easy incorporation into the structure. Although the prepared precursor transforms into LDH phases also when agitated in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist. The adsorption isotherm and kinetic studies show that the phenomena occurring on the Al-Ca precursor fit a pseudo-second-order kinetics with a Langmuir adsorption capacity of 59.45 mg/g. Besides, characterizations of the prepared precursor and the samples after adsorption are also performed by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Transmission electron microscope (TEM) to understand the reason of the preferential incorporation of Cr(VI) to the coexisting chloride salts during the LDH phase formation. - Graphical abstract: Activated Ca-Al hydroxides (C 3 A) transformed into Ca-Al-OH compound when agitated in water. Ca-Al precursor (C 3 A) was agitated in a hexavalent chromium (Cr(VI)) solution to form Al-Ca-CrO 4 LDH product. Ca-Al-CrO 4 LDH phase occurred preferentially to Ca-Al-MCl 2 LDH phases in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist. - Highlights: • Activated Ca-Al hydroxides transformed into LDH when agitated in water with some inorganic substances. • Hexavalent Cr was incorporated in the LDH structure at high adsorption capacity. • Ca-Al-Cr LDH phase occurred preferentially to Ca-Al-MCl 2 LDH phases with coexistence. • The prepared Ca-Al hydroxides had high performance as adsorbent even with high salinity of the solution.

Detection of OH radicals from IRAS sources

International Nuclear Information System (INIS)

Lewis, B.M.; Eder, J.; Terzian, Y.

1985-01-01

An efficient method for detecting new OH/infrared stars is to begin with IRAS source positions, selected for appropriate infrared colours, and using radio-line observations to confirm the OH properties. The authors demonstrate the validity of this approach here, using the Arecibo 305 m radio-telescope to confirm the 1,612 MHz line observations of sources in IRAS Circulars 8 and 9; the present observations identify 21 new OH/infrared stars. The new sources have weaker 1,612 MHz fluxes, bluer (60-25) μm colours and a smaller mean separation between the principal emission peaks than previous samples. (author)

Hydrogen-Bonding Network and OH Stretch Vibration of Cellulose: Comparison of Computational Modeling with Polarized IR and SFG Spectra.

Science.gov (United States)

Lee, Christopher M; Kubicki, James D; Fan, Bingxin; Zhong, Linghao; Jarvis, Michael C; Kim, Seong H

2015-12-10

Hydrogen bonds play critical roles in noncovalent directional interactions determining the crystal structure of cellulose. Although diffraction studies accurately determined the coordinates of carbon and oxygen atoms in crystalline cellulose, the structural information on hydrogen atoms involved in hydrogen-bonding is still elusive. This could be complemented by vibrational spectroscopy; but the assignment of the OH stretch peaks has been controversial. In this study, we performed calculations using density functional theory with dispersion corrections (DFT-D2) for the cellulose Iβ crystal lattices with the experimentally determined carbon and oxygen coordinates. DFT-D2 calculations revealed that the OH stretch vibrations of cellulose are highly coupled and delocalized through intra- and interchain hydrogen bonds involving all OH groups in the crystal. Additionally, molecular dynamics (MD) simulations of a single cellulose microfibril showed that the conformations of OH groups exposed at the microfibril surface are not well-defined. Comparison of the computation results with the experimentally determined IR dichroism of uniaxially aligned cellulose microfibrils and the peak positions of various cellulose crystals allowed unambiguous identification of OH stretch modes observed in the vibrational spectra of cellulose.

THE SPATIAL DISTRIBUTION OF OH AND CN RADICALS IN THE COMA OF COMET ENCKE

International Nuclear Information System (INIS)

Ihalawela, Chandrasiri A.; Pierce, Donna M.; Dorman, Garrett R.; Cochran, Anita L.

2011-01-01

Multiple potential parent species have been proposed to explain CN abundances in comet comae, but the parent has not been definitively identified for all comets. This study examines the spatial distribution of CN radicals in the coma of comet Encke and determines the likelihood that CN is a photodissociative daughter of HCN in the coma. Comet Encke is the shortest orbital period (3.3 years) comet known and also has a low dust-to-gas ratio based on optical observations. Observations of CN were obtained from 2003 October 22 to 24, using the 2.7 m telescope at McDonald Observatory. To determine the parent of CN, the classical vectorial model was modified by using a cone shape in order to reproduce Encke's highly aspherical and asymmetric coma. To test the robustness of the modified model, the spatial distribution of OH was also modeled. This also allowed us to obtain CN/OH ratios in the coma. Overall, we find the CN/OH ratio to be 0.009 ± 0.004. The results are consistent with HCN being the photodissociative parent of CN, but we cannot completely rule out other possible parents such as CH 3 CN and HC 3 N. We also found that the fan-like feature spans ∼90°, consistent with the results of Woodney et al..

Surface pH changes suggest a role for H+/OH- channels in salinity response of Chara australis.

Science.gov (United States)

Absolonova, Marketa; Beilby, Mary J; Sommer, Aniela; Hoepflinger, Marion C; Foissner, Ilse

2018-05-01

To understand salt stress, the full impact of salinity on plant cell physiology has to be resolved. Electrical measurements suggest that salinity inhibits the proton pump and opens putative H + /OH - channels all over the cell surface of salt sensitive Chara australis (Beilby and Al Khazaaly 2009; Al Khazaaly and Beilby 2012). The channels open transiently at first, causing a characteristic noise in membrane potential difference (PD), and after longer exposure remain open with a typical current-voltage (I/V) profile, both abolished by the addition of 1 mM ZnCl 2 , the main known blocker of animal H + channels. The cells were imaged with confocal microscopy, using fluorescein isothiocyanate (FITC) coupled to dextran 70 to illuminate the pH changes outside the cell wall in artificial fresh water (AFW) and in saline medium. In the early saline exposure, we observed alkaline patches (bright fluorescent spots) appearing transiently in random spatial distribution. After longer exposure, some of the spots became fixed in space. Saline also abolished or diminished the pH banding pattern observed in the untreated control cells. ZnCl 2 suppressed the alkaline spot formation in saline and the pH banding pattern in AFW. The osmotic component of the saline stress did not produce transient bright spots or affect banding. The displacement of H + from the cell wall charges, the H + /OH - channel conductance/density, and self-organization are discussed. No homologies to animal H + channels were found. Salinity activation of the H + /OH - channels might contribute to saline response in roots of land plants and leaves of aquatic angiosperms.

Studies of Gravity Waves Using Michelson Interferometer Measurements of OH (3-1 Bands

Directory of Open Access Journals (Sweden)

Young-In Won

2001-06-01

Full Text Available As part of a long-term program for polar upper atmospheric studies, temperatures and intensities of the OH (3-1 bands were derived from spectrometric observations of airglow emissions over King Sejong station (62.22o S, 301.25o E. These measurements were made with a Michelson interferometer to cover wavelength regions between 1000 nm and 2000 nm. A spectral analysis was performed to individual nights of data to acquire information on the waves in the upper mesosphere/lower thermosphere. It is assumed that the measured fluctuations in the intensity and temperature of the OH (3-1 airglow were caused by gravity waves propagating through the emission layer. Correlation of intensity and temperature variation revealed oscillations with periods ranging from 2 to 9 hours. We also calculated Krassovsky's parameter and compared with published values.

Vitamina D y cáncer: acción antineoplásica de la 1α, 25(OH2 -vitamina D3 Vitamin D and cancer: antineoplastic effects of 1α,25(OH2-vitamin D3

Directory of Open Access Journals (Sweden)

Verónica González Pardo

2012-04-01

Full Text Available La forma hormonalmente activa de la vitamina D, 1α,25(OH2-vitamina D3 (1α,25(OH2D3, además de desempeñar un rol crucial en el mantenimiento de la homeostasis de calcio en el cuerpo, también regula el crecimiento y la diferenciación de diferentes tipos celulares, incluyendo células cancerosas. Actualmente hay numerosos estudios que investigan los efectos de la hormona en estas células, debido al interés en el uso terapéutico del 1α,25(OH2D3 y de análogos con menor actividad calcémica para el tratamiento o prevención del cáncer. En este trabajo de revisión se describe el sistema endocrino de la vitamina D, su mecanismo de acción, su acción antineoplásica y se provee información sobre los últimos avances en el estudio de nuevos análogos de la hormona con menos actividad calcémica para el tratamiento del cáncer.The hormonal form of vitamin D, 1α,25(OH2-vitamin D3 (1α,25(OH2D3, in addition of playing a central role in the control of calcium homeostasis in the body, regulates the growth and differentiation of different cell types, including cancer cells. At present several epidemiologic and clinical studies investigate the effect of the hormone in these cells due to the interest in the therapeutic use of 1α,25(OH2D3 and analogues with less calcemic activity for prevention or treatment of cancer. This review describes vitamin D endocrine system, its mechanism of action, its antineoplastic activity and provides information about the latest advances in the study of new hormone analogues with less calcemic activity for cancer treatment.

The effect of H2O gas on volatilities of planet-forming major elements. I - Experimental determination of thermodynamic properties of Ca-, Al-, and Si-hydroxide gas molecules and its application to the solar nebula

Science.gov (United States)

Hashimoto, Akihiko

1992-01-01

The vapor pressures of Ca(OH)2(g), Al(OH)3(g), and Si(OH)4(g) molecules in equilibrium with solid calcium-, aluminum, and silicon-oxides, respectively, were determined, and were used to derive the heats of formation and entropies of these species, which are expected to be abundant under the currently postulated physical conditions in the primordial solar nebula. These data, in conjunction with thermodynamic data from literature, were used to calculate the relative abundances of M, MO(x), and M(OH)n gas species and relative volatilities of Fe, Mg, Si, Ca, and Al for ranges of temperature, total pressure, and H/O abundance ratio corresponding to the plausible ranges of physical conditions in the solar nebula. The results are used to explain how Ca and Al could have evaporated from Ca,Al-rich inclusions in carbonaceous chondrites, while Si, Mg, and Fe condensed onto them during the preaccretion alteration of CAIs.

Inhibition of radiation-induced DNA strand breaks by hoechst 33258: OH-radical scavenging and DNA radical quenching

International Nuclear Information System (INIS)

Adhikary, A.; Bothe, E.; Von Sonntag, C.; Adhikary, A.

1997-01-01

The minor-groove-binding dye Hoechst 33258 has been found to protect pBR322 DNA in aqueous solution against radiation-induced single-strand breaks (ssb). This protective effect has been assumed to be largely due to the scavenging of the strand-break-generating OH radicals by Hoechst. From D 37 values for ssb at different Hoechst concentrations the value of the OH radical scavenging constant of DNA-bound Hoechst has been estimated at k Ho/DNA = 2.7 * 10 11 dm 3 mol -1 . This unexpectedly high value has led us to study the reactions of OH radicals with Hoechst in the absence and in the presence of double-stranded calf thymus DNA (ds DNA) by pulse radiolysis, and the formation of radiation-induced ssb by low angle laser light scattering. The D 37 /D 37 0 values at different Hoechst concentrations agree with the values obtained by Martin and al. and demonstrate the protection. However, this protection cannot be explained on the basis of OH radical scavenging alone using the above rate constants. There must, in addition, be some quenching of DNA radicals. Hoechst radicals are formed in the later ms time range, i.e a long time after the disappearance of the OH radicals. This delayed Hoechst radical formation has been assigned to a a reaction of DNA radicals with Hoechst, thereby inhibiting strand breakage. In confirmation, pulse radiolysis of aqueous solution of nucleotides in the presence of Hoechst yields a similar delayed Hoechst radical formation. The data indicate that in DNA the cross-section of this quenching has a diameter of 3 to 4 base pairs per Hoechst molecule. (N.C.)

Infrared observations of circumstellar ammonia in OH/IR supergiants

International Nuclear Information System (INIS)

McLaren, R.A.; Betz, A.L.

1980-01-01

Ammonia has been detected in the circumstellar envelopes of VY Canis Majoris, VX Sagittarii, and IRC+10420 by means of several absorption lines in the ν 2 vibration-rotation band near 950 cm -1 . The line profiles are well resolved (0.2 km s -1 resolution) and show the gas being accelerated to terminal expansion velocities near 30 km s -1 . The observations reveal a method for determining the position of the central star on VLBI maps of OH maser emission to an accuracy of approx.0''.2. A firm lower limit of 2 x 10 15 cm -2 is obtained for the NH 3 column density in VY Canis Majoris

Spatial distribution of FIR rotationally excited CH+ and OH emission lines in the Orion Bar PDR.

Science.gov (United States)

Parikka, A; Habart, E; Bernard-Salas, J; Goicoechea, J R; Abergel, A; Pilleri, P; Dartois, E; Joblin, C; Gerin, M; Godard, B

2017-03-01

-440, which shows that OH can be an excellent tracer of UV-irradiated dense gas. The spatial distribution of CH + and OH revealed in our maps is consistent with previous modeling studies. Both formation pumping and nonreactive collisions in a UV-irradiated dense gas are important CH + J=3-2 excitation processes. The excitation of the OH Λ-doublet at 84 µm is mainly sensitive to the temperature and density.

Generation of OH Radical by Ultrasonic Irradiation in Batch and Circulatory Reactor

Science.gov (United States)

Fang, Yu; Shimizu, Sayaka; Yamamoto, Takuya; Komarov, Sergey

2018-03-01

Ultrasonic technology has been widely investigated in the past as one of the advance oxidation processes to treat wastewater, in this process acoustic cavitation causes generation of OH radical, which play a vital role in improving the treatment efficiency. In this study, OH radical formation rate was measured in batch and circulatory reactor by using Weissler reaction at various ultrasound output power. It is found that the generation rate in batch reactor is higher than that in circulatory reactor at the same output power. The generation rate tended to be slower when output power exceeds 137W. The optimum condition for circulatory reactor was found to be 137W output and 4L/min flow rate. Results of aluminum foil erosion test revealed a strong dependence of cavitation zone length on the ultrasound output power. This is assumed to be one of the reasons why the generation rate of HO radicals becomes slower at higher output power in circulatory reactor.

Insight into the mechanism of methanol assistance with syngas conversion over partially hydroxylated γ-Al2O3(110D) surface in slurry bed.

Science.gov (United States)

Bai, Bing; Bai, Hui; Cao, Hao-Jie; Gao, Zhi-Hua; Zuo, Zhi-Jun; Huang, Wei

2018-04-27

Despite numerous studies devoted to the various properties of γ-Al2O3, the explorations of its catalytic activity remain scarce. In this study, density functional theory calculations are performed to study the elementary adsorption and reaction mechanisms for syngas conversion on partially hydroxylated γ-Al2O3(110D) surface in liquid paraffin. It is found that the partially hydroxylated γ-Al2O3(110D) surface with the hydroxyl coverage of 8.9 OH nm-2 is formed by two dissociative adsorptions of H2O on the dry γ-Al2O3(110D) surface. The hydroxyl coverage conditions play a key role in determining the dominant reaction mechanism on account of the existence of strong hydrogen bonds. The preferential pathway for syngas conversion with assistance of methanol over the partially hydroxylated γ-Al2O3(110D) surface in liquid paraffin has been proven to be CH3OH → CH3O + H → CH3 + OH, CH3 + CO → CH3CO. C2H5OH is then formed by successive hydrogenation via the pathway CH3CO + 3H → CH3CHO + 2H → CH3CH2O + H → C2H5OH. Here, CH3CHO formation by CH3CO hydrogenation is not inhibited. Actually, with the assistance of partially hydroxylated γ-Al2O3, CH3CHO has been synthesized with high selectivity in our previous experiment by the reaction of methanol and syngas, which provides favorable evidence for our results. The rate-limiting step is the formation of CH3O from CH3OH dehydrogenation with an activation barrier of 122.2 kJ mol-1. Moreover, the reaction barrier of CO insertion into the adsorbed CH3 group is at least 89.4 kJ mol-1, lower than those of CH4, C2H6, and CH3OCH3 formations. ADCH charge and ESP analyses indicate that the typical (Al, O) Lewis acid-base pair may have a significant effect upon the initial C-C chain formation. Thus, the present study provides a new approach for the rational tailoring and designing of new catalysts with superior reactivity involved in syngas conversion.

Electrocatalytic Activity for CO, MeOH, and EtOH Oxidation on the Surface of Pt-Ru Nanoparticles Supported by Metal Oxide

Directory of Open Access Journals (Sweden)

Kwang-Sik Sim

2011-01-01

Full Text Available This paper describes the electrocatalytic activity for CO, MeOH, and EtOH oxidation on the surface of Pt-Ru nanoparticles supported by metal oxide (Nb-TiO2-H prepared for use in a fuel cell. To prepare Nb-TiO2-supported Pt-Ru nanoparticles, first, the Nb-TiO2 supports were prepared by sol-gel reaction of titanium tetraisopropoxide with a small amount of the niobium ethoxide in polystyrene (PS colloids. Second, Pt-Ru nanoparticles were then deposited by chemical reduction of the Pt4+ and Ru3+ ions onto Nb-TiO2 supports (Pt-Ru@Nb-TiO2-CS. Nb element was used to reduce electrical resistance to facilitate electron transport during the electrochemical reactions on a fuel cell electrode. Finally, the Pt-Ru@Nb-TiO2-H catalysts were formed by the removal of core-polystyrene ball from Pt-Ru@TiO2-CS at 500∘C. The successfully prepared Pt-Ru electrocatalysts were confirmed via TEM, XPS, and ICP analysis. The electrocatalytic efficiency of Pt-Ru nanoparticles was evaluated via CO, MeOH, and EtOH oxidation for use in a direct methanol fuel cell (DMFC. As a result, the Pt-Ru@Nb-TiO2-H electrodes showed high electrocatalytic activity for the electrooxidation of CO, MeOH, and EtOH.

Determining rotational temperatures from the OH(8-3 band, and a comparison with OH(6-2 rotational temperatures at Davis, Antarctica

Directory of Open Access Journals (Sweden)

F. Phillips

2004-04-01

Full Text Available Rotational temperatures derived from the OH(8–3 band may vary by ~18K depending on the choice of transition probabilities. This is of concern when absolute temperatures or trends determined in combination with measurements of other hydroxyl bands are important. In this paper, measurements of the OH(8–3 temperature-insensitive Q/P and R/P line intensity ratios are used to select the most appropriate transition probabilities for use with this band. Aurora, airglow and solar and telluric absorption in the OH(8–3 band are also investigated. Water vapour absorption of P₁(4, airglow or auroral contamination of P₁(2 and solar absorption in the vicinity of P₁(5 are concerns to be considered when deriving rotational temperatures from this band.

A comparison is made of temperatures derived from OH(6–2 and OH(8–3 spectra collected alternately at Davis (69° S, 78° E in 1990. An average difference of ~4K is found, with OH(8–3 temperatures being warmer, but a difference of this magnitude is within the two sigma uncertainty limit of the measurements.

Key words. Atmospheric composition and structure airglow and aurora; pressure, density, and temperature

Site determination of Ni atoms in Cu-Al-Ni shape memory alloys by electron channelling enhanced microanalysis

International Nuclear Information System (INIS)

Nakata, Yoshiyuki; Tadaki, Tsugio; Shimizu, Ken-ichi

1990-01-01

The crystallographic site of Ni atoms in the parent phase of differently heat-treated Cu-28.6Al-3.7Ni (at.%) shape memory alloys has been examined by electron channelling enhanced microanalysis (ALCHEMI) in order to clarify effects of heat-treatments on the Ni atom site and M s temperature. The heat-treatments were as follows: (a) Quenching into a 10% NaOH solution at 263 K, (b) Quenching into hot water at 363 K and (c) Aging at 523 K for 3.6 ks after treatment (b). The M s temperatures of specimens (a), (b) and (c) were 158, 185 and 259 K, respectively, increasing with lowering quenching rate or aging. ALCHEMI revealed that Ni atoms occupied an identical site in all the three kinds of specimens: The Ni atoms were located at the nearest neighbor sites around Al atoms. This preferential occupation of Ni atoms was attributed to the strong binding force between Ni and Al atoms. Thus, the change in M s temperature due to different heat-treatments was not directly related to the crystallographic site of Ni atoms, but might be caused by the ordering between the next nearest neighbor Cu and Al atoms. (author)

H2XP:OH2 Complexes: Hydrogen vs. Pnicogen Bonds

Directory of Open Access Journals (Sweden)

Ibon Alkorta

2016-02-01

Full Text Available A search of the Cambridge Structural Database (CSD was carried out for phosphine-water and arsine-water complexes in which water is either the proton donor in hydrogen-bonded complexes, or the electron-pair donor in pnicogen-bonded complexes. The range of experimental P-O distances in the phosphine complexes is consistent with the results of ab initio MP2/aug’-cc-pVTZ calculations carried out on complexes H2XP:OH2, for X = NC, F, Cl, CN, OH, CCH, H, and CH3. Only hydrogen-bonded complexes are found on the H2(CH3P:HOH and H3P:HOH potential surfaces, while only pnicogen-bonded complexes exist on H2(NCP:OH2, H2FP:OH2, H2(CNP:OH2, and H2(OHP:OH2 surfaces. Both hydrogen-bonded and pnicogen-bonded complexes are found on the H2ClP:OH2 and H2(CCHP:OH2 surfaces, with the pnicogen-bonded complexes more stable than the corresponding hydrogen-bonded complexes. The more electronegative substituents prefer to form pnicogen-bonded complexes, while the more electropositive substituents form hydrogen-bonded complexes. The H2XP:OH2 complexes are characterized in terms of their structures, binding energies, charge-transfer energies, and spin-spin coupling constants 2hJ(O-P, 1hJ(H-P, and 1J(O-H across hydrogen bonds, and 1pJ(P-O across pnicogen bonds.

The complex of PAMAM-OH dendrimer with Angiotensin (1-7) prevented the disuse-induced skeletal muscle atrophy in mice.

Science.gov (United States)

Márquez-Miranda, Valeria; Abrigo, Johanna; Rivera, Juan Carlos; Araya-Durán, Ingrid; Aravena, Javier; Simon, Felipe; Pacheco, Nicolás; González-Nilo, Fernando Danilo; Cabello-Verrugio, Claudio

2017-01-01

Angiotensin (1-7) (Ang-(1-7)) is a bioactive heptapeptide with a short half-life and has beneficial effects in several tissues - among them, skeletal muscle - by preventing muscle atrophy. Dendrimers are promising vehicles for the protection and transport of numerous bioactive molecules. This work explored the use of a neutral, non-cytotoxic hydroxyl-terminated poly(amidoamine) (PAMAM-OH) dendrimer as an Ang-(1-7) carrier. Bioinformatics analysis showed that the Ang-(1-7)-binding capacity of the dendrimer presented a 2:1 molar ratio. Molecular dynamics simulation analysis revealed the capacity of neutral PAMAM-OH to protect Ang-(1-7) and form stable complexes. The peptide coverage ability of the dendrimer was between ~50% and 65%. Furthermore, an electrophoretic mobility shift assay demonstrated that neutral PAMAM-OH effectively bonded peptides. Experimental results showed that the Ang-(1-7)/PAMAM-OH complex, but not Ang-(1-7) alone, had an anti-atrophic effect when administered intraperitoneally, as evaluated by muscle strength, fiber diameter, myofibrillar protein levels, and atrogin-1 and MuRF-1 expressions. The results of the Ang-(1-7)/PAMAM-OH complex being intraperitoneally injected were similar to the results obtained when Ang-(1-7) was systemically administered through mini-osmotic pumps. Together, the results suggest that Ang-(1-7) can be protected for PAMAM-OH when this complex is intraperitoneally injected. Therefore, the Ang-(1-7)/PAMAM-OH complex is an efficient delivery method for Ang-(1-7), since it improves the anti-atrophic activity of this peptide in skeletal muscle.

Green thermal-assisted synthesis and characterization of novel cellulose-Mg(OH)2 nanocomposite in PEG/NaOH solvent.

Science.gov (United States)

Ponomarev, Nikolai; Repo, Eveliina; Srivastava, Varsha; Sillanpää, Mika

2017-11-15

Synthesis of nanocomposites was performed using microcrystalline cellulose (MCC), MgCl 2 in PEG/NaOH solvent by a thermal-assisted method at different temperatures by varying time and the amount of MCC. Results of XRD, FTIR, and EDS mapping showed that the materials consisted of only cellulose (CL) and magnesium hydroxide (MH). According to FTIR and XRD, it was found that crystallinity of MH in cellulose nanocomposites is increased with temperature and heating time and decreased with increasing of cellulose amount. The PEG/NaOH solvent has a significant effect on cellulose and Mg(OH) 2 morphology. BET and BJH results demonstrated the effects of temperature and cellulose amount on the pore size corresponding to mesoporous materials. TG and DTG analyses showed the increased thermal stability of cellulose nanocomposites with increasing temperature. TEM and SEM analyses showed an even distribution of MH nanostructures with various morphology in the cellulose matrix. The cellulose presented as the polymer matrix in the nanocomposites. It was supposed the possible interaction between cellulose and Mg(OH) 2 . The novel synthesis method used in this study is feasible, cost-efficient and environmentally friendly. Copyright © 2017 Elsevier Ltd. All rights reserved.

Do vibrationally excited OH molecules affect middle and upper atmospheric chemistry?

Directory of Open Access Journals (Sweden)

T. von Clarmann

2010-10-01

Full Text Available Except for a few reactions involving electronically excited molecular or atomic oxygen or nitrogen, atmospheric chemistry modelling usually assumes that the temperature dependence of reaction rates is characterized by Arrhenius' law involving kinetic temperatures. It is known, however, that in the upper atmosphere the vibrational temperatures may exceed the kinetic temperatures by several hundreds of Kelvins. This excess energy has an impact on the reaction rates. We have used upper atmospheric OH populations and reaction rate coefficients for OH(v=0...9+O₃ and OH(v=0...9+O to estimate the effective (i.e. population weighted reaction rates for various atmospheric conditions. We have found that the effective rate coefficient for OH(v=0...9+O₃ can be larger by a factor of up to 1470 than that involving OH in its vibrational ground state only. At altitudes where vibrationally excited states of OH are highly populated, the OH reaction is a minor sink of O_x and O₃ compared to other reactions involving, e.g., atomic oxygen. Thus the impact of vibrationally excited OH on the ozone or O_x sink remains small. Among quiescent atmospheres under investigation, the largest while still small (less than 0.1% effect was found for the polar winter upper stratosphere and mesosphere. The contribution of the reaction of vibrationally excited OH with ozone to the OH sink is largest in the upper polar winter stratosphere (up to 4%, while its effect on the HO₂ source is larger in the lower thermosphere (up to 1.5% for polar winter and 2.5% for midlatitude night conditions. For OH(v=0...9+O the effective rate coefficients are lower by up to 11% than those involving OH in its vibrational ground state. The effects on the odd oxygen sink are negative and can reach −3% (midlatitudinal nighttime lowermost thermosphere, i.e. neglecting vibrational excitation overestimates the odd

Investigating causality in the association between 25(OH)D and schizophrenia.

Science.gov (United States)

Taylor, Amy E; Burgess, Stephen; Ware, Jennifer J; Gage, Suzanne H; Richards, J Brent; Davey Smith, George; Munafò, Marcus R

2016-05-24

Vitamin D deficiency is associated with increased risk of schizophrenia. However, it is not known whether this association is causal or what the direction of causality is. We performed two sample bidirectional Mendelian randomization analysis using single nucleotide polymorphisms (SNPs) robustly associated with serum 25(OH)D to investigate the causal effect of 25(OH)D on risk of schizophrenia, and SNPs robustly associated with schizophrenia to investigate the causal effect of schizophrenia on 25(OH)D. We used summary data from genome-wide association studies and meta-analyses of schizophrenia and 25(OH)D to obtain betas and standard errors for the SNP-exposure and SNP-outcome associations. These were combined using inverse variance weighted fixed effects meta-analyses. In 34,241 schizophrenia cases and 45,604 controls, there was no clear evidence for a causal effect of 25(OH)D on schizophrenia risk. The odds ratio for schizophrenia per 10% increase in 25(OH)D conferred by the four 25(OH)D increasing SNPs was 0.992 (95% CI: 0.969 to 1.015). In up to 16,125 individuals with measured serum 25(OH)D, there was no clear evidence that genetic risk for schizophrenia causally lowers serum 25(OH)D. These findings suggest that associations between schizophrenia and serum 25(OH)D may not be causal. Therefore, vitamin D supplementation may not prevent schizophrenia.

Reductive amination of ethanol to ethylamines over Ni/Al_2O_3 catalysts

International Nuclear Information System (INIS)

Park, Jun Hyun; Hong, Eunpyo; An, Sang Hee; Shin, Chae-Ho; Lim, Dong-Hee

2017-01-01

Ni(x)/Al_2O_3 (x=wt%) catalysts with Ni loadings of 5-25 wt% were prepared via a wet impregnation method on an γ-Al_2O_3 support and subsequently applied in the reductive amination of ethanol to ethylamines. Among the various catalysts prepared, Ni(10)/Al2O3 exhibited the highest metal dispersion and the smallest Ni particle size, resulting in the highest catalytic performance. To reveal the effects of reaction parameters, a reductive amination process was performed by varying the reaction temperature (T), weight hourly space velocity (WHSV), and NH_3 and H_2 partial pressures in the reactions. In addition, on/off experiments for NH_3 and H_2 were also carried out. In the absence of NH_3 in the reactant stream, the ethanol conversion and selectivities towards the different ethylamine products were significantly reduced, while the selectivity to ethylene was dominant due to the dehydration of ethanol. In contrast, in the absence of H_2, the selectivity to acetonitrile significantly increased due to dehydrogenation of the imine intermediate. Although a small amount of catalyst deactivation was observed in the conversion of ethanol up to 10 h on stream due to the formation of nickel nitride, the Ni(10)/Al_2O_3 catalyst exhibited stable catalytic performance over 90 h under the optimized reaction conditions (i.e., T=190 .deg. C, WHSV=0.9 h"-"1, and EtOH/NH_3/H_2 molar ratio=1/1/6).

Exome sequencing reveals VCP mutations as a cause of familial ALS

OpenAIRE

Johnson, Janel O.; Mandrioli, Jessica; Benatar, Michael; Abramzon, Yevgeniya; Van Deerlin, Vivianna M.; Trojanowski, John Q.; Gibbs, J Raphael; Brunetti, Maura; Gronka, Susan; Wuu, Joanne; Ding, Jinhui; McCluskey, Leo; Martinez-Lage, Maria; Falcone, Dana; Hernandez, Dena G.

2010-01-01

Using exome sequencing, we identified a p.R191Q amino acid change in the valosin-containing protein (VCP) gene in an Italian family with autosomal dominantly inherited amyotrophic lateral sclerosis (ALS). Mutations in VCP have previously been identified in families with Inclusion Body Myopathy, Paget’s disease and Frontotemporal Dementia (IBMPFD). Screening of VCP in a cohort of 210 familial ALS cases and 78 autopsy-proven ALS cases identified four additional mutations including a p.R155H mut...

Certification of OHS management in a Nordic context

DEFF Research Database (Denmark)

Hendriksen, Kåre; Jørgensen, Kirsten; Jørgensen, Ulrik

2009-01-01

’s management to decide which elements of OHS performance they commit to while the only explicit OHS demand is to comply with legal requirements. Additionally the certification is covered by the accreditation standard requirements of confidentiality, where as the validity of a certificate end up being hidden...... for the involved stakeholders. The consequences of these foundational elements of the existing management standard are analysed and exemplified. The Nordic Minister Council has funded the project, OHS Certification as Control Instrument and Control Strategy, which together with earlier studies of the working...

Investigation of OH dynamics in the argon sensitized pulse radiolysis of water vapor

International Nuclear Information System (INIS)

Bera, R.K.; Hanrahan, R.J.

1986-01-01

Reactions of OH radical were studied in systems containing 650 torr Ar and from 0.5 to 9 torr H 2 O using the method of pulse radiolysis-absorption spectroscopy. It was found that initial concentrations of OH radical increased as a function of water vapor pressure. Although loss of OH with time followed approximate second order kinetics, the raw data were fitted arbitrarily to a first order rate expression, because a second order fit requires knowledge of absolute initial OH concentrations. These can be computed from measured initial OH absorption if the extinction coefficient is known, but an accurate value was not available initially. The half-life for OH loss decreased at higher water pressures. Dependence of OH half-life on OH concentration occurs because homogeneous OH loss processes are second order in reaction intermediates, whose concentration increases with added H 2 O. A contribution by water in chaperoning OH/OH and OH/H combination is also important

Effect of LiOH, NaOH and KOH on corrosion and oxide microstructure of Zr-based alloys

International Nuclear Information System (INIS)

Jeong, Y.H.; Kim, H.G.; Jung, Y.H.; Ruhmann, H.

1999-01-01

Long-term corrosion test, SIMS analysis, and TEM microstructural study were carried out to investigate the corrosion characteristics and mechanism of Zr alloys in alkali hydroxides. The corrosion tests were performed in solutions of LiOH, NaOH, KOH, RbOH, and CsOH at 350 deg. C for 500 days. SIMS analysis was performed for the specimens prepared to have an equal oxide thickness. TEM studies on the specimens with an equal oxide thickness in various solutions in both pre- and post-transition regimes were also conducted. The corrosion rate in alkali hydroxide solutions was observed to decrease as the ionic radius of alkali cation was increased. The penetration depth of cation into the oxide decreases with increasing the ionic radius of cation. Even though the oxide thickness was equal, the different oxide morphologies were observed in specimens. Namely, in LiOH solution the oxide morphology was transformed early from columnar to equiaxed structure. However, in KOH solution the columnar structure was maintained up to post-transition regime. Based on the corrosion test, SIMS analysis, and microstructural study, the cation is considered to control the corrosion in a alkali hydroxide solution and its effect is dependent on the concentration of alkali and the oxide thickness. The slight acceleration of the corrosion rate at a low concentration is thought to be caused by cation incorporation into oxide while the significant acceleration at a high concentration is due to the transformation of oxide microstructure that would be induced by cation incorporation. KOH was shown not to affect significantly the corrosion and the hydrogen pickup of Zircaloy. Therefore, it has a potential for PWR application only from the point of view of Zircaloy corrosion. (author)

Observations of OH and HO2 radicals in coastal Antarctica

Directory of Open Access Journals (Sweden)

S. J.-B. Bauguitte

2007-08-01

Full Text Available OH and HO2 radical concentrations have been measured in the boundary layer of coastal Antarctica for a six-week period during the austral summer of 2005. The measurements were performed at the British Antarctic Survey's Halley Research Station (75° 35' S, 26° 19' W, using the technique of on-resonance laser-induced fluorescence to detect OH, with HO2 measured following chemical conversion through addition of NO. The mean radical levels were 3.9×105 molecule cm−3 for OH, and 0.76 ppt for HO2 (ppt denotes parts per trillion, by volume. Typical maximum (local noontime levels were 7.9×105 molecule cm−3 and 1.50 ppt for OH and HO2 respectively. The main sources of HOx were photolysis of O3 and HCHO, with potentially important but uncertain contributions from HONO and higher aldehydes. Of the measured OH sinks, reaction with CO and CH4 dominated, however comparison of the observed OH concentrations with those calculated via the steady state approximation indicated that additional co-reactants were likely to have been present. Elevated levels of NOx resulting from snowpack photochemistry contributed to HOx cycling and enhanced levels of OH, however the halogen oxides IO and BrO dominated the CH3O2 – HO2 – OH conversion in this environment, with associated ozone destruction.

Electronic quenching of OH(A) by water in atmospheric pressure plasmas and its influence on the gas temperature determination by OH(A-X) emission

NARCIS (Netherlands)

Bruggeman, P.J.; Iza, F.; Guns, P.; Lauwers, D.; Kong, M.G.; Aranda Gonzalvo, Y.; Leys, C.; Schram, D.C.

2010-01-01

In this paper it is shown that electronic quenching of OH(A) by water prevents thermalization of the rotational population distribution of OH(A). This means that the observed ro-vibrational OH(A-X) emission band is (at least partially) an image of the formation process and is determined not only by

G331.512–0.103: An Interstellar Laboratory for Molecular Synthesis. I. The Ortho-to-para Ratios for CH3OH and CH3CN

Science.gov (United States)

Mendoza, Edgar; Bronfman, Leonardo; Duronea, Nicolas U.; Lépine, Jacques R. D.; Finger, Ricardo; Merello, Manuel; Hervías-Caimapo, Carlos; Gama, Diana R. G.; Reyes, Nicolas; Åke-Nyman, Lars

2018-02-01

Spectral line surveys reveal rich molecular reservoirs in G331.512–0.103, a compact radio source in the center of an energetic molecular outflow. In this first work, we analyze the physical conditions of the source by means of CH3OH and CH3CN. The observations were performed with the APEX Telescope. Six different system configurations were defined to cover most of the band within (292–356) GHz as a consequence, we detected a forest of lines toward the central core. A total of 70 lines of A/E–CH3OH and A/E–CH3CN were analyzed, including torsionally excited transitions of CH3OH ({ν }t=1). In a search for all the isotopologues, we identified transitions of 13CH3OH. The physical conditions were derived considering collisional and radiative processes. We found common temperatures for each A and E symmetry of CH3OH and CH3CN; the derived column densities indicate an A/E equilibrated ratio for both tracers. The results reveal that CH3CN and CH3OH trace a hot and cold component with {T}k∼ 141 K and {T}k∼ 74 K, respectively. In agreement with previous ALMA observations, the models show that the emission region is compact (≲ 5\\buildrel{\\prime\\prime}\\over{.} 5) with gas density n(H2) = (0.7–1)×107 cm‑3. The CH3OH/CH3CN abundance ratio and the evidences for prebiotic and complex organic molecules suggest a rich and active chemistry toward G331.512–0.103.

Structural and optical properties of nanocrystalline CdSe and Al:CdSe thin films for photoelectrochemical application

Energy Technology Data Exchange (ETDEWEB)

Gawali, Sanjay A. [Electrochemical Materials Laboratory, Department of Physics, Shivaji University, Kolhapur - 416 004 (India); Bhosale, C.H., E-mail: bhosale_ch@yahoo.com [Electrochemical Materials Laboratory, Department of Physics, Shivaji University, Kolhapur - 416 004 (India)

2011-10-03

Highlights: {yields} The CdSe and Al:CdSe thin films have been successfully deposited by SPT. {yields} Hexagonal cubic structured CdSe and Al: CdSe thin films are observed. {yields} Large number of fine grains, Uniform and compact growth morphology. {yields} Hydrophilic surface nature. {yields} Al:CdSe have better PEC performance than CdSe. - Abstract: Nanocrystalline CdSe and Al:CdSe semiconductor thin films have been successfully synthesized onto amorphous and FTO glass substrates by spray pyrolysis technique. Aqueous solutions containing precursors of Cd and Se have been used to obtain good quality films. The optimized films have been characterized for their structural, morphological, wettability and optical properties. X-ray diffraction (XRD) studies show that the films are polycrystalline in nature with hexagonal crystal structure. Scanning electron microscopy (SEM) studies show that the film surface is smooth, uniform and compact in nature. Water wettability study reveals that the films are hydrophilic behavior. The formation of CdSe and Al:CdSe thin film were confirmed with the help of FTIR spectroscopy. UV-vis spectrophotometric measurement showed a direct allowed band gap lying in the range 1.673-1.87 eV. Output characteristics were studied by using cell configuration n- CdSe/Al:CdSe |1 M (NaOH + Na{sub 2} + S)|C. An efficient solar cell having a power conversion efficiency of 0.38% at illumination 25 mW cm{sup -2} was fabricated.

Investigation of Mg(OH){sub 2} nanoparticles as an antibacterial agent

Energy Technology Data Exchange (ETDEWEB)

Dong Chunxu [Dalian University of Technology, State Key Laboratory of Fine Chemicals, School of Chemical Engineering (China); Cairney, John [Georgia Institute of Technology, School of Biology (United States); Sun Qunhui [Georgia Institute of Technology, Institute of Paper Science and Technology (United States); Maddan, Orville Lee [Aqua Resources Corporation (United States); He Gaohong [Dalian University of Technology, State Key Laboratory of Fine Chemicals, School of Chemical Engineering (China); Deng Yulin, E-mail: yulin.deng@chbe.gatech.ed [Georgia Institute of Technology, Institute of Paper Science and Technology (United States)

2010-08-15

Our experimental results of using Mg(OH){sub 2} nanoparticles as an antibacterial agent are reported in this study. The antibacterial behavior of Mg(OH){sub 2} nanoparticles in liquid culture and in paper sheets was investigated. The colony forming units (CFU) counting and the headspace gas chromatography (HS-GC) measurement were used to determine the cell viability. Results indicate that Mg(OH){sub 2} nanoparticles are effective antibacterial agent against Escherichia coli (E. coli) and Burkholderia phytofirmans, and the OH{sup -} and Mg{sup 2+} ions in Mg(OH){sub 2} water suspension were found not to be the reason for killing the bacteria. Mg(OH){sub 2} nanoparticles could be added directly to wood pulp to make paper sheets, whose antibacterial efficiency increased with the increase of the nanoparticle amount. The possible mechanism of antibacterial effect of Mg(OH){sub 2} nanoparticles is discussed.

Recovery of UMo alloy from UMo/Al dispersion fuel plates by dissolution

International Nuclear Information System (INIS)

Ren Meng; Li Jia; Liu Jinhong; Zhu Changgui

2011-01-01

Methods for dissolving UMo/Al dispersion fuel plates in the compounded mixed basic aqueous (NaOH and NaNO 3 ) are studied on laboratory scale. After removing the clad and the matrix of the substandard UMo/Al dispersion fuel elements, the U loss ratios are calculated and the granularity distributions of the recovered UMo alloy powder are analyzed by the metallurgical microscope. Besides, the phase structure and the composition of the recovered UMo alloy powder are analyzed by the XRD. The results indicate that as the concentration of NaOH increases, uranium loss ratio increases; but as the concentration of NaNO 3 increases, U loss ration increases firstly and then decreases subsequently; generally, the U recovery ratios are more than 99.3%. The granularity of recovered UMo powders are very small and most parts of γ-U have been oxidated to UO 2 . Therefore, further study is required to determined whether the recovered UMo alloy could be returned to the product line. (authors)

A highly sensitive, single selective, fluorescent sensor for Al{sup 3+} detection and its application in living cell imaging

Energy Technology Data Exchange (ETDEWEB)

Ye, Xing-Pei [Department of Physics and Chemistry, Henan Polytechnic University, Jiaozuo 454000 (China); Sun, Shao-bo; Li, Ying-dong [Institute of Integrated Traditional and Western Medicine, Gansu University of Traditional Chinese Medicine, Lanzhou 730000 (China); Zhi, Li-hua [Department of Physics and Chemistry, Henan Polytechnic University, Jiaozuo 454000 (China); Wu, Wei-na, E-mail: wuwn08@hpu.edu.cn [Department of Physics and Chemistry, Henan Polytechnic University, Jiaozuo 454000 (China); Wang, Yuan, E-mail: wangyuan08@hpu.edu.cn [Department of Physics and Chemistry, Henan Polytechnic University, Jiaozuo 454000 (China)

2014-11-15

A new o-aminophenol-based fluorogenic chemosensor methyl 3,5-bis((E)-(2-hydroxyphenylimino)methyl)-4-hydroxybenzoate 1 have been synthesized by Schiff base condensation of methyl 3,5-diformyl-4-hydroxybenzoate with o-aminophenol, which exhibits high selectivity and sensitivity toward Al{sup 3+}. Fluorescence titration studies of receptors 1 with different metal cations in CH{sub 3}OH medium showed highly selective and sensitive towards Al{sup 3+} ions even in the presence of other commonly coexisting metal ions. The detection limit of Al{sup 3+} ions is at the parts per billion level. Interestingly, the Al(III) complex of 1 offered a large Stokes shift (>120 nm), which can miximize the selfquenching effect. In addition, possible utilization of this receptor as bio-imaging fluorescent probe to detect Al{sup 3+} in human cervical HeLa cancer cell lines was also investigated by confocal fluorescence microscopy. - Highlights: • A new Schiff base chemosensor is reported. • The sensor for Al{sup 3+} offers large Stokes shift. • The detection limit of Al{sup 3+} in CH{sub 3}OH solution is at the parts per billion level. • The utilization of sensor for the monitoring of Al{sup 3+} levels in living cells was examined.

Infrared observations of circumstellar ammonia in OH/IR supergiants

Science.gov (United States)

Mclaren, R. A.; Betz, A. L.

1980-01-01

Ammonia has been detected in the circumstellar envelopes of VY Canis Majoris, VX Sagittarii, and IRC +10420 by means of several absorption lines in the nu-2 vibration-rotation band near 950 kaysers. The line profiles are well resolved (0.2 km/sec resolution) and show the gas being accelerated to terminal expansion velocities near 30 km/sec. The observations reveal a method for determining the position of the central star on VLBI maps of OH maser emission to an accuracy of approximately 0.2 arcsec. A firm lower limit of 2 x 10 to the 15th/sq cm is obtained for the NH3 column density in VY Canis Majoris.

Composition and structural study of solution-processed Zn(S,O,OH) thin films grown using H{sub 2}O{sub 2} based deposition route

Energy Technology Data Exchange (ETDEWEB)

Buffière, M., E-mail: marie.buffiere@imec.be [Institut des Matériaux Jean Rouxel (IMN)-UMR 6502, Université de Nantes, CNRS, 2 rue de la Houssinière, BP 32229, 44322 Nantes Cedex 3 (France); 44Solar, 14 rue Kepler, 44240 La Chapelle-sur-Erdre (France); Gautron, E. [Institut des Matériaux Jean Rouxel (IMN)-UMR 6502, Université de Nantes, CNRS, 2 rue de la Houssinière, BP 32229, 44322 Nantes Cedex 3 (France); Hildebrandt, T. [Institut de Recherche et Développement sur l' Energie Photovoltaïque (IRDEP)-UMR 7174 EDF-CNRS-ENSCP, 6 quai Watier-78401 Chatou Cedex (France); Harel, S.; Guillot-Deudon, C.; Arzel, L. [Institut des Matériaux Jean Rouxel (IMN)-UMR 6502, Université de Nantes, CNRS, 2 rue de la Houssinière, BP 32229, 44322 Nantes Cedex 3 (France); Naghavi, N. [Institut de Recherche et Développement sur l' Energie Photovoltaïque (IRDEP)-UMR 7174 EDF-CNRS-ENSCP, 6 quai Watier-78401 Chatou Cedex (France); Barreau, N. [Institut des Matériaux Jean Rouxel (IMN)-UMR 6502, Université de Nantes, CNRS, 2 rue de la Houssinière, BP 32229, 44322 Nantes Cedex 3 (France); Kessler, J. [Institut des Matériaux Jean Rouxel (IMN)-UMR 6502, Université de Nantes, CNRS, 2 rue de la Houssinière, BP 32229, 44322 Nantes Cedex 3 (France); 44Solar, 14 rue Kepler, 44240 La Chapelle-sur-Erdre (France)

2013-05-01

Recent results have revealed that the low deposition time issue of chemical bath deposited (CBD) Zn(S,O,OH) buffer layer used in Cu(In,Ga)Se{sub 2} (CIGSe) solar cells could be resolved using H{sub 2}O{sub 2} as an additive in the chemical bath solution. Although the use of this additive does not hinder the electrical properties of the resulting Zn(S,O,OH)-buffered CIGSe solar cells, the impact of H{sub 2}O{sub 2} on the Zn(S,O,OH) properties remains unclear. The present contribution aims at determining the chemical composition and the microstructure of Zn(S,O,OH) film deposited by CBD using the alternative deposition bath containing the standard zinc sulfate, thiourea, ammonia but also H{sub 2}O{sub 2} additive. Both X-ray photoemission spectroscopy and energy dispersive X-ray spectroscopy analyses reveal higher sulfur content in alternatively deposited Zn(S,O,OH), since the first step growth of the layer. According to transmission electron microscopy analyses, another consequence of the higher deposition rate achieved when adding H{sub 2}O{sub 2} in the bath is the modification of the absorber/buffer interface. This could be explained by the enhancement of the cluster growth mechanism of the layer. - Highlights: ► The Zn(S,O,OH) layer composition can vary with the chemical bath process used. ► The alternative process leads to a faster incorporation of sulfur in the layer. ► No ZnS epitaxial layer has been found at absorber/alternative buffer interface. ► The use of H{sub 2}O{sub 2} enhances the cluster-by-cluster growth mechanism.

Glyphosate and glufosinate detection at electrogenerated NiAl-LDH thin films

Energy Technology Data Exchange (ETDEWEB)

Khenifi, Aicha [Laboratoire des Materiaux Inorganiques, UMR CNRS 6002, Universite Blaise Pascal, Clermont-Ferrand (France); Laboratoire de physico-chimie des materiaux, catalyse et environnement Usto, Oran, El M' nouar (Algeria); Derriche, Zoubir [Laboratoire de physico-chimie des materiaux, catalyse et environnement Usto, Oran, El M' nouar (Algeria); Forano, Claude; Prevot, Vanessa [Laboratoire des Materiaux Inorganiques, UMR CNRS 6002, Universite Blaise Pascal, Clermont-Ferrand (France); Mousty, Christine, E-mail: Christine.Mousty@univ-bpclermont.fr [Laboratoire des Materiaux Inorganiques, UMR CNRS 6002, Universite Blaise Pascal, Clermont-Ferrand (France); Scavetta, Erika, E-mail: scavetta@fci.unibo.it [Laboratorio di Chimica Analitica, Dipartimento di Chimica Fisica ed Inorganica, Universita degli Studi di Bologna (Italy); Ballarin, Barbara; Guadagnini, Lorella; Tonelli, Domenica [Laboratorio di Chimica Analitica, Dipartimento di Chimica Fisica ed Inorganica, Universita degli Studi di Bologna (Italy)

2009-11-10

An amperometric sensor based on Ni{sub 1-x}Al{sub x}(OH){sub 2}NO{sub 3x}.nH{sub 2}O layered double hydroxide (LDH) has been developed for the electrochemical analysis in one step of two herbicides: glyphosate (N-(phosphonomethyl)glycine, Glyp) and glufosinate ((DL-homoalanine-4-yl)-methylphosphinic acid, Gluf). NiAl-LDH was prepared by coprecipitation or by electrodeposition at the Pt electrode surface. Inorganic films were fully characterized by X-ray diffraction, Raman spectroscopy and scanning electron microscopy. Adsorption isotherms of Glyp onto this inorganic lamellar material have been established. Electrocatalytic oxidation of Glyp and Gluf is possible at the Ni{sup 3+} centres of the structure. The electrochemical responses of the NiAl-LDH modified electrode were obtained by cyclic voltammetry and chronoamperometry at 0.49 V/SCE as a function of herbicide concentration in 0.1 M NaOH solution. The electrocatalytic response showed a linear dependence on the Glyp concentration ranging between 0.01 and 0.9 mM with a detection limit of 1 {mu}M and sensitivity 287 mA/M cm{sup 2}. The sensitivity found for Gluf was lower (178 mA/M cm{sup 2}).

Spatial distribution of FIR rotationally excited CH+ and OH emission lines in the Orion Bar PDR⋆

Science.gov (United States)

Parikka, A.; Habart, E.; Bernard-Salas, J.; Goicoechea, J. R.; Abergel, A.; Pilleri, P.; Dartois, E.; Joblin, C.; Gerin, M.; Godard, B.

2016-01-01

244-440, which shows that OH can be an excellent tracer of UV-irradiated dense gas. Conclusions The spatial distribution of CH+ and OH revealed in our maps is consistent with previous modeling studies. Both formation pumping and nonreactive collisions in a UV-irradiated dense gas are important CH+ J=3-2 excitation processes. The excitation of the OH Λ-doublet at 84 µm is mainly sensitive to the temperature and density. PMID:28260804

Effects of heating atmosphere on formation of crystalline citrate-derived LaAlO3 nanoparticles

International Nuclear Information System (INIS)

Yu, Hsuan-Fu; Guo, Yu-Man

2011-01-01

Research highlights: → LaAlO 3 can be crystallized at 550 deg. C in an oxygen-enriched atmosphere. → Calcining the citrate precursor in oxygen atmosphere lowers the reaction temperatures to form crystalline LaAlO 3 . → In oxygen atmosphere, pure citrate-derived LaAlO 3 nanoparticles can be produced at 700 deg. C. - Abstract: Crystalline LaAlO 3 nanoparticles were synthesized at relative low temperatures, using a citrate-precursor technique. La(NO 3 ) 3 , Al(NO 3 ) 3 , and C 3 H 4 (OH)(COOH) 3 , in a molar ratio of 1:1:1, were dissolved in deionized water. NH 4 OH was used to adjust the aqueous solution to pH 7. After drying, the citrate precursors were charred at 350 deg. C, followed by calcination at different temperatures, in air or oxygen atmosphere. The thermochemical properties of the resultant particles were analyzed using thermogravimetric and differential thermal analysis, X-ray diffractometry, infrared spectroscopy, scanning electron microscopy, and transmission electron microscopy. Effects of calcination temperature and heating atmosphere on the formation of crystalline LaAlO 3 nanoparticles were investigated. In O 2 atmosphere, clacining the citrate-derived charred solid precursor at 700 deg. C for 3 h can decompose all intermediates to produce pure LaAlO 3 nanoparticles (particle sizes ≤ 100 nm) with an average crystallite size of about 24 nm and possessing high sinterability.

Key issues of ultraviolet radiation of OH at high altitudes

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yuhuai; Wan, Tian; Jiang, Jianzheng; Fan, Jing [State Key Laboratory of High Temperature Gasdynamics, Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190 (China)

2014-12-09

Ultraviolet (UV) emissions radiated by hydroxyl (OH) is one of the fundamental elements in the prediction of radiation signature of high-altitude and high-speed vehicle. In this work, the OH A{sup 2}Σ{sup +}→X{sup 2}Π ultraviolet emission band behind the bow shock is computed under the experimental condition of the second bow-shock ultraviolet flight (BSUV-2). Four related key issues are discussed, namely, the source of hydrogen element in the high-altitude atmosphere, the formation mechanism of OH species, efficient computational algorithm of trace species in rarefied flows, and accurate calculation of OH emission spectra. Firstly, by analyzing the typical atmospheric model, the vertical distributions of the number densities of different species containing hydrogen element are given. According to the different dominating species containing hydrogen element, the atmosphere is divided into three zones, and the formation mechanism of OH species is analyzed in the different zones. The direct simulation Monte Carlo (DSMC) method and the Navier-Stokes equations are employed to compute the number densities of the different OH electronically and vibrationally excited states. Different to the previous work, the trace species separation (TSS) algorithm is applied twice in order to accurately calculate the densities of OH species and its excited states. Using a non-equilibrium radiation model, the OH ultraviolet emission spectra and intensity at different altitudes are computed, and good agreement is obtained with the flight measured data.

Construction of g-C_3N_4/Al_2O_3 hybrids via in-situ acidification and exfoliation with enhanced photocatalytic activity

International Nuclear Information System (INIS)

Wang, Xiao-jing; Liu, Chao; Li, Xu-li; Li, Fa-tang; Li, Yu-pei; Zhao, Jun; Liu, Rui-hong

2017-01-01

Highlights: • Ultrathin g-C_3N_4/Al_2O_3 hybrids are prepared via in-situ reaction. • The structure modification role of in-situ formed HNO_3 for g-C_3N_4 is found. • The ultrathin g-C_3N_4 nanosheets are formed by the acidified melamine and Al(OH)_3. • In-situ calcination of melamine and Al(OH)_3 benefits the contact of C_3N_4 and Al_2O_3. • The activity of g-C_3N_4/Al_2O_3 is 16.6 times that of pristine g-C_3N_4 in degrading RhB. - Abstract: Homogeneous ultrathin g-C_3N_4 nanosheets/Al_2O_3 heterojunctions are synthesized using melamine and Al(NO_3)_3 via in-situ reaction and the following thermal polymerization approach. The in-situ reaction between melamine and Al(NO_3)_3 results in the existence of HNO_3-acidified melamine and Al(OH)_3 aggregates via the hydrolysis of Al(NO_3)_3. After thermal polymerization, the aggregates are converted to g-C_3N_4/Al_2O_3 composites. The thermal polymerization of acidified melamine and the support effect of aluminum hydroxide for g-C_3N_4 during the calcination process lead to highly dispersed amrophous Al_2O_3 on ultrathin g-C_3N_4 nanosheets, which is beneficial for the separation of photogenerated electron-hole pairs in the heterojunction. The degradation rate for Rhodamine B (RhB) over the most activie sample is 16.6 times than that of pristine g-C_3N_4 under visible light irradiation, which can be attributed to the high specific surface area, highly dispersion of amorphous Al_2O_3 on ultrathin g-C_3N_4 nanosheet, and the effective electrons transfer from g-C_3N_4 to the amorphous Al_2O_3.

UV photolysis of 4-iodo-, 4-bromo-, and 4-chlorophenol: Competition between C-Y (Y = halogen) and O-H bond fission

Science.gov (United States)

Sage, Alan G.; Oliver, Thomas A. A.; King, Graeme A.; Murdock, Daniel; Harvey, Jeremy N.; Ashfold, Michael N. R.

2013-04-01

The wavelength dependences of C-Y and O-H bond fission following ultraviolet photoexcitation of 4-halophenols (4-YPhOH) have been investigated using a combination of velocity map imaging, H Rydberg atom photofragment translational spectroscopy, and high level spin-orbit resolved electronic structure calculations, revealing a systematic evolution in fragmentation behaviour across the series Y = I, Br, Cl (and F). All undergo O-H bond fission following excitation at wavelengths λ ≲ 240 nm, on repulsive ((n/π)σ*) potential energy surfaces (PESs), yielding fast H atoms with mean kinetic energies ˜11 000 cm-1. For Y = I and Br, this process occurs in competition with prompt C-I and C-Br bond cleavage on another (n/π)σ* PES, but no Cl/Cl* products unambiguously attributable to one photon induced C-Cl bond fission are observed from 4-ClPhOH. Differences in fragmentation behaviour at longer excitation wavelengths are more marked. Prompt C-I bond fission is observed following excitation of 4-IPhOH at all λ ≤ 330 nm; the wavelength dependent trends in I/I* product branching ratio, kinetic energy release, and recoil anisotropy suggest that (with regard to C-I bond fission) 4-IPhOH behaves like a mildly perturbed iodobenzene. Br atoms are observed when exciting 4-BrPhOH at long wavelengths also, but their velocity distributions suggest that dissociation occurs after internal conversion to the ground state. O-H bond fission, by tunnelling (as in phenol), is observed only in the cases of 4-FPhOH and, more weakly, 4-ClPhOH. These observed differences in behaviour can be understood given due recognition of (i) the differences in the vertical excitation energies of the C-Y centred (n/π)σ* potentials across the series Y = I increased spin-orbit coupling in, particularly, 4-IPhOH. The present results provide (another) reminder of the risks inherent in extrapolating photochemical behaviour measured for one molecule at one wavelength to other (related) molecules and to

Synthesis of γ-Al2O3 nanowires through a boehmite precursor route

Indian Academy of Sciences (India)

has applications in absorbent, catalyst carrier and reinforce- ment of ceramic .... nia into the transparent solution, Al(OH)3 with colloidal form generates .... 99 1823. Zhou J, Deng S Z, Chen J, She J C and Xu N S 2002 Chem. Phys. Lett. 365 505.

Surface chemistry of plasma-assisted atomic layer deposition of Al2O3 studied by infrared spectroscopy

NARCIS (Netherlands)

Langereis, E.; Keijmel, J.; Sanden, van de M.C.M.; Kessels, W.M.M.

2008-01-01

The surface groups created during plasma-assisted atomic layer deposition (ALD) of Al2O3 were studied by infrared spectroscopy. For temperatures in the range of 25–150 °C, –CH3 and –OH were unveiled as dominant surface groups after the Al(CH3)3precursor and O2 plasma half-cycles, respectively. At

Chemical synthesis of flower-like hybrid Cu(OH)2/CuO electrode: Application of polyvinyl alcohol and triton X-100 to enhance supercapacitor performance.

Science.gov (United States)

Shinde, S K; Fulari, V J; Kim, D-Y; Maile, N C; Koli, R R; Dhaygude, H D; Ghodake, G S

2017-08-01

In this research article, we report hybrid nanomaterials of copper hydroxide/copper oxide (Cu(OH) 2 /CuO). A thin films were prepared by using a facile and cost-effective successive ionic layer adsorption and reaction (SILAR) method. As-synthesized and hybrid Cu(OH) 2 /CuO with two different surfactants polyvinyl alcohol (PVA) and triton-X 100 (TRX-100) was prepared having distinct morphological, structural, and supercapacitor properties. The surface of the thin film samples were examined by scanning electron microscopy (SEM). A nanoflower-like morphology of the Cu(OH) 2 /CuO nanostructures arranged vertically was evidenced on the stainless steel substrate. The surface was well covered by nanoflake-like morphology and formed a uniform Cu(OH) 2 /CuO nanostructures after treating with surfactants. X-ray diffraction patterns were used to confirm the hybrid phase of Cu(OH) 2 /CuO materials. The electrochemical properties of the pristine Cu(OH) 2 /CuO, PVA:Cu(OH) 2 /CuO, TRX-100:Cu(OH) 2 /CuO films were observed by cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy technique. The electrochemical examination reveals that the Cu(OH) 2 /CuO electrode has excellent specific capacitance, 292, 533, and 443Fg -1 with pristine, PVA, and TRX-100, respectively in 1M Na 2 SO 4 electrolyte solution. The cyclic voltammograms (CV) of Cu(OH) 2 /CuO electrode shows positive role of the PVA and TRX-100 to enhance supercapacitor performance. Copyright © 2017 Elsevier B.V. All rights reserved.

Atom-radical reaction dynamics of O(3P)+C3H5→C3H4+OH: Nascent rovibrational state distributions of product OH

Science.gov (United States)

Park, Jong-Ho; Lee, Hohjai; Kwon, Han-Cheol; Kim, Hee-Kyung; Choi, Young-Sang; Choi, Jong-Ho

2002-08-01

The reaction dynamics of ground-state atomic oxygen [O(3P)] with allyl radicals (C3H5) has been investigated by applying a combination of crossed beams and laser induced fluorescence techniques. The reactants O(3P) and C3H5 were produced by the photodissociation of NO2 and the supersonic flash pyrolysis of precursor allyl iodide, respectively. A new exothermic channel of O(3P)+C3H5→C3H4+OH was observed and the nascent internal state distributions of the product OH (X 2Π:υ″=0,1) showed substantial bimodal internal excitations of the low- and high-N″ components without Λ-doublet and spin-orbit propensities in the ground and first excited vibrational states. With the aid of the CBS-QB3 level of ab initio theory and Rice-Ramsperger-Kassel-Marcus calculations, it is predicted that on the lowest doublet potential energy surface the major reaction channel of O(3P) with C3H5 is the formation of acrolein (CH2CHCHO)+H, which is consistent with the previous bulk kinetic experiments performed by Gutman et al. [J. Phys. Chem. 94, 3652 (1990)]. The counterpart C3H4 of the probed OH product in the title reaction is calculated to be allene after taking into account the factors of reaction enthalpy, barrier height and the number of intermediates involved along the reaction pathway. On the basis of population analyses and comparison with prior calculations, the statistical picture is not suitable to describe the reactive atom-radical scattering processes, and the dynamics of the title reaction is believed to proceed through two competing dynamical pathways. The major low N″-components with significant vibrational excitation may be described by the direct abstraction process, while the minor but extraordinarily hot rotational distribution of high N″-components implies that some fraction of reactants is sampled to proceed through the indirect short-lived addition-complex forming process.

Discovery of pulsed OH maser emission stimulated by a pulsar.

Science.gov (United States)

Weisberg, Joel M; Johnston, Simon; Koribalski, Bärbel; Stanimirovic, Snezana

2005-07-01

Stimulated emission of radiation has not been directly observed in astrophysical situations up to this time. Here we demonstrate that photons from pulsar B1641-45 stimulate pulses of excess 1720-megahertz line emission in an interstellar hydroxyl (OH) cloud. As this stimulated emission is driven by the pulsar, it varies on a few-millisecond time scale, which is orders of magnitude shorter than the quickest OH maser variations previously detected. Our 1612-megahertz spectra are inverted copies of the 1720-megahertz spectra. This "conjugate line" phenomenon enables us to constrain the properties of the interstellar OH line-producing gas. We also show that pulsar signals undergo significantly deeper OH absorption than do other background sources, which confirms earlier tentative findings that OH clouds are clumpier on small scales than are neutral hydrogen clouds.

H+-type and OH- -type biological protonic semiconductors and complementary devices.

Science.gov (United States)

Deng, Yingxin; Josberger, Erik; Jin, Jungho; Roudsari, Anita Fadavi; Rousdari, Anita Fadavi; Helms, Brett A; Zhong, Chao; Anantram, M P; Rolandi, Marco

2013-10-03

Proton conduction is essential in biological systems. Oxidative phosphorylation in mitochondria, proton pumping in bacteriorhodopsin, and uncoupling membrane potentials by the antibiotic Gramicidin are examples. In these systems, H(+) hop along chains of hydrogen bonds between water molecules and hydrophilic residues - proton wires. These wires also support the transport of OH(-) as proton holes. Discriminating between H(+) and OH(-) transport has been elusive. Here, H(+) and OH(-) transport is achieved in polysaccharide- based proton wires and devices. A H(+)- OH(-) junction with rectifying behaviour and H(+)-type and OH(-)-type complementary field effect transistors are demonstrated. We describe these devices with a model that relates H(+) and OH(-) to electron and hole transport in semiconductors. In turn, the model developed for these devices may provide additional insights into proton conduction in biological systems.

High-temperature rate constant measurements for OH+xylenes

KAUST Repository

Elwardani, Ahmed Elsaid; Badra, Jihad; Farooq, Aamir

2015-01-01

The overall rate constants for the reactions of hydroxyl (OH) radicals with o-xylene (k 1), m-xylene (k 2), and p-xylene (k 3) were measured behind reflected shock waves over 890-1406K at pressures of 1.3-1.8atm using OH laser absorption near 306

Topotactic transition of α-Co(OH)2 to β-Co(OH)2 anchored on CoO nanoparticles during electrochemical water oxidation: synergistic electrocatalytic effects.

Science.gov (United States)

Kundu, Sumana; Malik, Bibhudatta; Prabhakaran, Amrutha; Pattanayak, Deepak K; Pillai, Vijayamohanan K

2017-08-29

Herein, we report a single step, anionic surfactant-assisted, low temperature-hydrothermal synthetic strategy of CoO nanoparticles anchored on β-Co(OH) 2 nanosheets which show a low overpotential (295 mV @ 10 mA cm -2 ) for the oxygen evolution reaction (OER). They also demonstrate much better kinetic parameters compared to the state-of-the-art RuO 2 . Interestingly, under the OER operational conditions (in alkaline medium), the topotactic transformation of α-Co(OH) 2 to a stable Brucite-like β-Co(OH) 2 phase leads to a synergistic interaction between the β-Co(OH) 2 sheets on the CoO nanoparticles for enhancing the OER electrocatalytic activity.

Harvard ER-2 OH laser-induced fluorescence instrument

Science.gov (United States)

Wennberg, Paul O.; Anderson, James G.

1994-01-01

The Harvard ER-2 OH instrument is scheduled to be integrated into the NASA ER-2 high altitude aircraft ozone payload in August 1992. Design and fabrication is presently underway. This experiment is a descendant of a balloon borne instrument designed and built in the mid-1980s. The ER-2 instrument is being designed to measure OH and HO2 as part of the NASA ozone payload for the investigation of processes controlling the concentration of stratospheric ozone. Although not specifically designed to do so, it is hoped that valid measurements of OH and HO2 can be made in the remote free troposphere with this instrument.

Unraveling the reaction mechanism on nitrile hydration catalyzed by [Pd(OH2)4]2+: insights from theory.

Science.gov (United States)

Tílvez, Elkin; Menéndez, María I; López, Ramón

2013-07-01

Density functional theory methodologies combined with continuum and discrete-continuum descriptions of solvent effects were used to investigate the [Pd(OH2)4](2+)-catalyzed acrylonitrile hydration to yield acrylamide. According to our results, the intramolecular hydroxide attack mechanism and the external addition mechanism of a water molecule with rate-determining Gibbs energy barriers in water solution of 27.6 and 28.3 kcal/mol, respectively, are the most favored. The experimental kinetic constants of the hydration started by hydroxide, k(OH), and water, k(H2O), attacks for the cis-[Pd(en)(OH2)2](2+)-catalyzed dichloroacetonitrile hydration rendered Gibbs energy barriers whose energy difference, 0.7 kcal/mol, is the same as that obtained in the present study. Our investigation reveals the nonexistence of the internal attack of a water ligand for Pd-catalyzed nitrile hydration. At the low pHs used experimentally, the equilibrium between [Pd(OH2)3(nitrile)](2+) and [Pd(OH2)2(OH)(nitrile)](+) is completely displaced to [Pd(OH2)3(nitrile)](2+). Experimental studies in these conditions stated that water acts as a nucleophile, but they could not distinguish whether it was a water ligand, an external water molecule, or a combination of both possibilities. Our theoretical explorations clearly indicate that the external water mechanism becomes the only operative one at low pHs. On the basis of this mechanistic proposal it is also possible to ascribe an (1)H NMR signal experimentally detected to the presence of a unidentate iminol intermediate and to explain the influence of nitrile concentration reported experimentally for nitriles other than acrylonitrile in the presence of aqua-Pd(II) complexes. Therefore, our theoretical point of view on the mechanism of nitrile hydration catalyzed by aqua-Pd(II) complexes can shed light on these relevant processes at a molecular level as well as afford valuable information that can help in designing new catalysts in milder and more

UV photolysis of 4-iodo-, 4-bromo-, and 4-chlorophenol: competition between C-Y (Y = halogen) and O-H bond fission.

Science.gov (United States)

Sage, Alan G; Oliver, Thomas A A; King, Graeme A; Murdock, Daniel; Harvey, Jeremy N; Ashfold, Michael N R

2013-04-28

The wavelength dependences of C-Y and O-H bond fission following ultraviolet photoexcitation of 4-halophenols (4-YPhOH) have been investigated using a combination of velocity map imaging, H Rydberg atom photofragment translational spectroscopy, and high level spin-orbit resolved electronic structure calculations, revealing a systematic evolution in fragmentation behaviour across the series Y = I, Br, Cl (and F). All undergo O-H bond fission following excitation at wavelengths λ ≲ 240 nm, on repulsive ((n∕π)σ∗) potential energy surfaces (PESs), yielding fast H atoms with mean kinetic energies ∼11,000 cm(-1). For Y = I and Br, this process occurs in competition with prompt C-I and C-Br bond cleavage on another (n∕π)σ∗ PES, but no Cl∕Cl∗ products unambiguously attributable to one photon induced C-Cl bond fission are observed from 4-ClPhOH. Differences in fragmentation behaviour at longer excitation wavelengths are more marked. Prompt C-I bond fission is observed following excitation of 4-IPhOH at all λ ≤ 330 nm; the wavelength dependent trends in I∕I∗ product branching ratio, kinetic energy release, and recoil anisotropy suggest that (with regard to C-I bond fission) 4-IPhOH behaves like a mildly perturbed iodobenzene. Br atoms are observed when exciting 4-BrPhOH at long wavelengths also, but their velocity distributions suggest that dissociation occurs after internal conversion to the ground state. O-H bond fission, by tunnelling (as in phenol), is observed only in the cases of 4-FPhOH and, more weakly, 4-ClPhOH. These observed differences in behaviour can be understood given due recognition of (i) the differences in the vertical excitation energies of the C-Y centred (n∕π)σ∗ potentials across the series Y = I bond strength, cf. that of the rival O-H bond, and (ii) the much increased spin-orbit coupling in, particularly, 4-IPhOH. The present results provide (another) reminder of the risks inherent in extrapolating photochemical

Rotationally resolved photodetachment spectrum of OH{sup -}, exposed with velocity-map imaging

Energy Technology Data Exchange (ETDEWEB)

Gibson, S T; Cavanagh, S J; Lewis, B R, E-mail: Stephen.Gibson@anu.edu.a, E-mail: Steven.Cavanagh@anu.edu.a [Research School of Physics and Engineering, Australian National University, Canberra ACT 0200 (Australia)

2009-11-01

The photodetachment spectrum of OH{sup -} has been measured using velocity-map imaging for the detection of photoelectrons. The relative electron kinetic-energy resolution, determined to be ({Delta}E/E) = 0.5%, resolves individual rotational transitions, including R3(0) that defines the electron affinity. Previously unobserved, N-, O-, S-, T-branch transitions are also revealed. The angular anisotropy parameters in general exhibit values consistent with electron detachment from O{sup -}, {beta} {approx} -0.8, except for the S, T branches which are significantly more isotropic, with {beta} {approx} -0.4.

RECONSTRUCTION OF CALCINED Zn -Al LAYERED DOUBLE HYDROXIDES DURING TETRACYCLINE ADSORPSION

Directory of Open Access Journals (Sweden)

G. M. Starukh

2015-12-01

Full Text Available Zn-Al mixed oxides containing ZnO different degree crystallinity were obtained by calcinations of Zn-Al layered double hydroxides (LDHs. The reconstruction of calcined Zn-Al LDHs has been performed under stirring in aqueous suspensions. The assynthesized LDHs, its decomposition products, as well as the reconstructed solids upon hydration were characterized by XRD, N2adsorption, differential and thermal gravimetric analysis. It was found that the ability of Zn-Al LDHs to recover a layered structure under the hydration of mixed oxides depends on the degree of ZnO crystallinity. The partial reconstruction of Zn-Al layered structure occurs in tetracycline solutions irrespective to the degree of ZnO crystallinity in calcined LDHs. Calcined Zn-Al LDHs demonstrate the higher adsorption capacity to tetracycline in comparison with as-prepared Zn-Al LDHs. The adsorption of TC on calcined and uncalcined ZnAl LDHs occurs on the centers of one particular type. It is suggested that surface complexation of the A-ring ligand of TC with Al-OH centers takes place.

A discussion on the determination of atmospheric OH and its trends

Directory of Open Access Journals (Sweden)

P. Jöckel

2003-01-01

Full Text Available The oxidation efficiency of the troposphere is largely determined by the hydroxyl radical and its global distribution. Its presence limits the lifetime of most trace gases. Because of the great importance of several of these gases for climate, ozone budget and OH itself, it is of fundamental importance to acquire knowledge about atmospheric OH and possible trends in its concentrations. In the past, average concentrations of OH and trends were largely derived using industrially produced CH3CCl3 as a chemical tracer. The analyses have given valuable, but also rather uncertain results. In this paper we describe an idealized computer aided tracer experiment which has as one of its goals to derive tracer concentration weighted, global average k(OH>, where the temporal and spatial OH distribution is prescribed and k is the reaction rate coefficient of OH with a hitherto never produced (Gedanken tracer, which is injected at a number of surface sites in the atmosphere in well known amounts over a given time period. Using a three-dimensional (3-D time-dependent chemistry transport model, k(OH> can be accurately determined from the calculated 3-D tracer distribution. It is next explored how well k(OH> can be retrieved solely from tracer measurements at a limited number of surface sites. The results from this analysis are encouraging enough to actually think about the feasibility to carry out a global dedicated tracer experiment to derive k(OH> and its temporal trends. However, before that, we propose to test the methods that are used to derive k(OH>, so far largely using CH3CCl3, with an idealized tracer experiment, in which a global chemistry transport model is used to calculate the ``Gedanken'' tracer distribution, representing the real 3-D world, from which k(OH> is derived, using only the tracer information from a limited set of surface sites. We propose here that research groups which are, or will be, involved in global average OH studies to

Summertime OH reactivity from a receptor coastal site in the Mediterranean Basin

Directory of Open Access Journals (Sweden)

N. Zannoni

2017-10-01

Full Text Available Total hydroxyl radical (OH reactivity, the total loss frequency of the hydroxyl radical in ambient air, provides the total loading of OH reactants in air. We measured the total OH reactivity for the first time during summertime at a coastal receptor site located in the western Mediterranean Basin. Measurements were performed at a temporary field site located in the northern cape of Corsica (France, during summer 2013 for the project CARBOSOR (CARBOn within continental pollution plumes: SOurces and Reactivity–ChArMEx (Chemistry and Aerosols Mediterranean Experiment. Here, we compare the measured total OH reactivity with the OH reactivity calculated from the measured reactive gases. The difference between these two parameters is termed missing OH reactivity, i.e., the fraction of OH reactivity not explained by the measured compounds. The total OH reactivity at the site varied between the instrumental LoD (limit of detection  =  3 s−1 to a maximum of 17 ± 6 s−1 (35 % uncertainty and was 5 ± 4 s−1 (1σ SD – standard deviation on average. It varied with air temperature exhibiting a diurnal profile comparable to the reactivity calculated from the concentration of the biogenic volatile organic compounds measured at the site. For part of the campaign, 56 % of OH reactivity was unexplained by the measured OH reactants (missing reactivity. We suggest that oxidation products of biogenic gas precursors were among the contributors to missing OH reactivity.

The complex of PAMAM-OH dendrimer with Angiotensin (1–7) prevented the disuse-induced skeletal muscle atrophy in mice

Science.gov (United States)

Márquez-Miranda, Valeria; Abrigo, Johanna; Rivera, Juan Carlos; Araya-Durán, Ingrid; Aravena, Javier; Simon, Felipe; Pacheco, Nicolás; González-Nilo, Fernando Danilo; Cabello-Verrugio, Claudio

2017-01-01

Angiotensin (1–7) (Ang-(1–7)) is a bioactive heptapeptide with a short half-life and has beneficial effects in several tissues – among them, skeletal muscle – by preventing muscle atrophy. Dendrimers are promising vehicles for the protection and transport of numerous bioactive molecules. This work explored the use of a neutral, non-cytotoxic hydroxyl-terminated poly(amidoamine) (PAMAM-OH) dendrimer as an Ang-(1–7) carrier. Bioinformatics analysis showed that the Ang-(1–7)-binding capacity of the dendrimer presented a 2:1 molar ratio. Molecular dynamics simulation analysis revealed the capacity of neutral PAMAM-OH to protect Ang-(1–7) and form stable complexes. The peptide coverage ability of the dendrimer was between ~50% and 65%. Furthermore, an electrophoretic mobility shift assay demonstrated that neutral PAMAM-OH effectively bonded peptides. Experimental results showed that the Ang-(1–7)/PAMAM-OH complex, but not Ang-(1–7) alone, had an anti-atrophic effect when administered intraperitoneally, as evaluated by muscle strength, fiber diameter, myofibrillar protein levels, and atrogin-1 and MuRF-1 expressions. The results of the Ang-(1–7)/PAMAM-OH complex being intraperitoneally injected were similar to the results obtained when Ang-(1–7) was systemically administered through mini-osmotic pumps. Together, the results suggest that Ang-(1–7) can be protected for PAMAM-OH when this complex is intraperitoneally injected. Therefore, the Ang-(1–7)/PAMAM-OH complex is an efficient delivery method for Ang-(1–7), since it improves the anti-atrophic activity of this peptide in skeletal muscle. PMID:28331320

Synthesis, characterization and flocculation activity of novel Fe(OH)3-polyacrylamide hybrid polymer

International Nuclear Information System (INIS)

Wang Huilong; Cui Jinyan; Jiang Wenfeng

2011-01-01

Highlights: → The preparation of a novel Fe(OH) 3 -PAM hybrid polymer flocculant is achieved via free radical solution polymerization. → Flocculation of kaolin suspensions using this novel Fe(OH) 3 -PAM hybrid polymer flocculant is revealed in this study. → The statistical model was first applied for calculating the thermodynamic parameters for the kaolin flocculating process. - Abstract: A novel Fe(OH) 3 -polyacrylamide inorganic-organic hybrid polymer (FHPAM) was synthesized via free radical solution polymerization initiated by a redox initiation system ((NH 4 ) 2 S 2 O 8 -NaHSO 3 ) in an aqueous medium. Reaction parameters influencing the intrinsic viscosity and the yield of the hybrid polymer, such as initiator concentration, monomer mass fraction, temperature and reaction time were investigated and optimized. The results show that the maximum intrinsic viscosity and up to 94% yields of the hybrid polymer can be achieved using initiator concentration of 0.3% with acrylamide monomer mass fraction of 20% under solution polymerization at 40 deg. C for 7 h. The physicochemical properties of this hybrid flocculant were characterized with TEM, FTIR spectra, TGA, and conductivity. It was found that a chemical bond exists between Fe(OH) 3 colloid and polyacrylamide chains in the FHPAM. The application of the hybrid polymer for the treatment of 2.5 g L -1 kaolin suspension indicates that it had an excellent flocculation capacity and its flocculation efficiency was much better than that of commercial available polyacrylamide (PAM) and polymeric ferric sulfate (PFS). The optimal conditions for the flocculation treatment of kaolin suspension were the FHPAM dosage of 40 mg L -1 at pH 7.0. The thermodynamic parameters for the flocculation process were calculated based on a statistical model. Interpretation of the results was given.

Study of ethanol-induced Golgi disorganization reveals the potential mechanism of alcohol-impaired N-glycosylation

Science.gov (United States)

Casey, Carol A.; Bhat, Ganapati; Holzapfel, Melissa S.; Petrosyan, Armen

2016-01-01

Background It is known that ethanol (EtOH) and its metabolites have a negative effect on protein glycosylation. The fragmentation of the Golgi apparatus induced by alteration of the structure of largest Golgi matrix protein, giantin, is the major consequence of damaging effects of EtOH-metabolism on the Golgi, however, the link between this and abnormal glycosylation remains unknown. Because previously we have shown that Golgi morphology dictates glycosylation, we examined the effect EtOH administration has on function of Golgi residential enzymes involved in N-glycosylation. Methods HepG2 cells transfected with mouse ADH1 (VA-13 cells) were treated with 35 mM ethanol for 72 h. Male Wistar rats were pair-fed Lieber-DeCarli diets for 5 to 8 weeks. Characterization of Golgi-associated mannosyl (α-1,3-)-glycoprotein beta-1,2-N-acetylglucosaminyltransferase (MGAT1), α-1,2-mannosidase (Man-I) and α-mannosidase II (Man-II) were performed in VA-13 cells and rat hepatocytes followed by 3D Structured Illumination Microscopy (SIM). Results First, we detected that EtOH administration results in the loss of sialylated N-glycans on asialoglycoprotein receptor, however the high mannose-type N-glycans are increased. Further analysis by 3D SIM microscopy revealed that EtOH treatment despite Golgi disorganization does not change cis-Golgi localization for Man-I, but does induce medial-to-cis relocation of MGAT1 and Man-II. Using different approaches, including electron microscopy, we revealed that EtOH treatment results in dysfunction of Arf1 GTPase followed by a deficiency in COPI vesicles at the Golgi. Silencing beta-COP or expression of GDP-bound mutant Arf1(T31N) mimics the EtOH effect on retaining MGAT1 and Man-II at the cis-Golgi, suggesting that (a) EtOH specifically blocks activation of Arf1, and (b) EtOH alters the proper localization of Golgi enzymes through impairment of COPI. Importantly, the level of MGAT1 was reduced, because likely MGAT1, contrary to Man-I and Man

Hydrogen production by sodium borohydride in NaOH aqueous solution

Science.gov (United States)

Wang, Q.; Zhang, L. F.; Zhao, Z. G.

2018-01-01

The kinetics of hydrolysis reaction of NaBH4 in NaOH aqueous solution is studied. The influence of pH of the NaOH aqueous solution on the rate of hydrogen production and the hydrogen production efficiency are studied for the hydrolysis reaction of NaBH4. The results show that the activation energy of hydrolysis reaction of NaBH4 increased with the increase of the initial pH of NaOH aqueous solution.With the increasing of the initial pH of NaOH aqueous solution, the rate of hydrogen production and hydrogen production efficiency of NaBH4 hydrolysis decrease.

Upconversion luminescence of Er3+/Yb3+ doped Sr5(PO4)3OH phosphor powders

Science.gov (United States)

Mokoena, P. P.; Swart, H. C.; Ntwaeaborwa, O. M.

2018-04-01

Sr5(PO4)3OH co-doped with Er3+and Yb3+ powder phosphors were synthesized by urea combustion method. The crystal structure was analyzed using X-ray diffraction (XRD). Particle morphology was analyzed using a Jeol JSM 7800F thermal field emission scanning electron microscope (FE-SEM) and the chemical composition analysis was carried out using an Oxford Instruments AzTEC energy dispersive spectrometer (EDS) attached to the FE-SEM. Upconversion emission was measured by using a FLS980 Spectrometer equipped with a 980 nm NIR laser as the excitation source, and a photomultiplier (PMT) detector. The XRD data of the Sr5(PO4)3OH powder exhibited characteristic diffraction patterns of the hexagonal structure referenced in the standard JCPDS card number 00-033-1348. The sharp peaks revealed the formation of crystalline Sr5(PO4)3OH. The powders were made up of hexagonal nanospheres. The enhanced red emission due to the 4F9/2 → 4I15/2 transitions of Er3+ was observed and was attributed to up conversion (UC) energy transfer from Yb3+. The upconversion energy transfer mechanism from Yb3+ to Er3+ is discussed.

Extraction of gelatin from catfish bone using NaOH and its utilization as a template on mesoporous silica alumina

Science.gov (United States)

Nuryanto, R.; Trisunaryanti, W.; Falah, I. I.; Triyono

2018-04-01

Gelatin extraction from catfish bone using NaOH and its utilization as a template on a synthesis of mesoporous silica-alumina had been investigated. The extraction was prepared by immersing 25 g catfish bone in 125 mL of NaOH in concentration of 0.0; 0.05; 0.10; 0.15 and 0.20 M for 24 h, then washing with demineralized water until pH 7, followed by immersed the bone into 125 mL of 1 M HCl for 1 h, then washed using demineralized water into pH 5. To produce gelatin the bone was refluxed with 100 mL demineralized water at 70°C for 5 h then evaporated at 50°C. The dry gelatin was characterized using FTIR and electrophoresis (SDS-PAGE). The best performance of gelatin was produced by NaOH 0.10 M. The gelatin consists of amide A, B, I, II, III and molecular weight of 25-200kDa. Silica and Alumina material prepared from Lapindo mud extraction. Dry Lapindo mud crushed and filtered until pass 100 mesh, then reflux using 6 M HCl (1:4 w/V) at 90°C for 5h then filtered. The filtrate was consisting alumina solution adding with 6 M NaOH (2/3 V/V) them filtered. The filtrate then injected by CO2 gas for 30 minutes and filtered, the residue was calcined at 500°C for 5h. The residual of Lapindo mud dried and refluxed with 6 M NaOH (1:4 w/v) at 90 °C. After 5h filtered and the filtrate added by HCl to pH 8 and filtered, the residual then dried. The Si and Al were then analyzed by XRF and consist of silica and alumina for 99.1 and 87.73%, respectively. Silica-alumina was prepared using silica and alumina extracted from Lapindo mud. 6 g of SiO2 and 2 g of NaOH was immersed in 62 mL of demineralized water then added with alumina solution (0.204 g alumina in 30 mL demineralized water). The gelatin solution (5 g gelatin in 70 mL demineralized water) was dropped into the silica-alumina while stirring at 50°C for 4 h and aging for 24 h. The synthesized silica alumina was analysed using FTIR and surface area analyser. The FT-IR spectra indicated the TO4 (T=Si, Al) vibration at wave

The use of CH3OH additive to NaOH for etching alpha particle tracks in a CR-39 plastic nuclear track detector

International Nuclear Information System (INIS)

Ashry, A.H.; Abdalla, A.M.; Rammah, Y.S.; Eisa, M.; Ashraf, O.

2014-01-01

Fast detection of alpha particles in CR-39 detectors was investigated using a new chemical etchant. 252 Cf and 241 Am sources were used for irradiating samples of CR-39 SSNTDs with fission fragments and alpha particles in air at normal temperature and pressure. A series of experimental chemical etching are carried out using new etching solution (8 ml of 10N NaOH+1 ml CH 3 OH) at 60 °C to detect alpha particle in short time in CR-39 detectors. Suitable analyzing software has been used to analyze experimental data. From fission and alpha track diameters, the value of bulk etching rate is equal to 2.73 μm/h. Both the sensitivity and etching efficiency were found to vary with the amount of methanol in the etching solution. Pure NaOH was used as a control to compare with the result from etching in NaOH with different concentrations of CH 3 OH. The etching efficiency is determined and compared with conventional aqueous solution of 6.25N NaOH at 70 °C for etching time equals 5 h. In this study, the obtained etching efficiency shows a considerable agreement with the previous work. - Highlights: • The value of bulk etching rate is equal to 2.73 μm/h. • Fast detection of alpha particles in CR-39 detectors. • Samples of CR-39 have been irradiated with fission fragments. • Etching efficiency was determined

Self-Assembled Hollow Spheres of β-Ni(OH) 2 and Their Derived Nanomaterials

KAUST Repository

Zhang, Shengmao

2009-03-10

This paper describes a novel solution-based chemical process to architect hollow spheres of β-Ni(OH) 2 with controllable sizes in submicrometer and micrometer regimes. In the synthesis, starting nickel salt (nitrate) is first converted to 6-coordinated nickel ion complex [Ni(EDA) 3] 2+ (bidentate ligand EDA = C 2H 4(NH 2) 2) to avoid rapid solid formation. Hollow and core - shell β-Ni(OH) 2 spheres can be obtained with this template-free approach under one-pot conditions. The β-Ni(OH) 2 spheres are constructed from petal-like nanobuilding units which in turn are formed from even smaller nanocrystallites. The obtained porous β-Ni(OH) 2 spheres have a large specific surface area and show a unimodal pore-size distribution. Several preparative parameters have been examined and optimized. In particular, the concentration of divalent nickel in the starting solutions plays an important role in controlling thickness of the petal-like β-Ni(OH) 2 flakes and diameter of spheres. The β-Ni(OH) 2 flakes self-assemble into final spherical products through a donut-like structural intermediate. Furthermore, the β-Ni(OH) 2 hollow spheres can be used as solid precursors to synthesize other nanostructured derivatives. In this work, phase pure inorganic nanostructures, carbon nanotube (CNT) - inorganic nanocomposites, and inorganic - inorganic nanocom-posites (e.g., NiO, Ni, NiO/Ni, Ni/β-Ni(OH) 2, CNTs/NiO, CNTs/Ni, Ni@CNTs, Fe(OH) 3/β-Ni(OH) 2, Co(OH) 2/β-Ni(OH) 2, and Mg(OH) 2/β-Ni(OH) 2) have been prepared via solid-state thermal decomposition, gas-phase reduction, solution-based reduction, surface oxidation, chemical vapor deposition, and liquid-phase deposition. A greater picture for general synthesis of Ni-containing nanomaterials is thus obtained. © 2009 American Chemical Society.

Comparison of in situ ionizing radiation effects on Raman and photoluminescence intensity of high OH, low OH silica, and fluoride core fibers

Science.gov (United States)

Bilodeau, T. G.; Ewing, K. J.; Nau, G. M.; Aggarwal, I. D.

1995-06-01

An in situ study of the effects of ionizing radiation on the strength of the Raman and photoluminescence signal of high OH, low OH, and fluoride core fibers has been performed with 514.5 nm laser excitation. The fibers were irradiated with a 60Co source at a constant dose rate of 560 rads/h. The high OH fiber displayed a much slower decay of the fiber Raman intensity than the other two fibers during irradiation. The fluoride fiber exhibited the quickest decline in Raman signal with the intensity dropping by a factor of 1000 in less than 20 min. The Raman intensity of the low OH silica fiber recovered to greater than 90% of its pre-irradiation value after a post-irradiation photoanneal with 488 nm laser light. The silica fibers displayed an increase in intensity of a broad photoluminescence feature centered at 650 nm. However the fiber photoluminescence intensity remained much weaker than the Raman intensity throughout the irradiations.

Effect of monobutylether ethylene glycol on Mg/Al layered double hydroxide: a physicochemical and conductivity study

International Nuclear Information System (INIS)

Paulo, Maria Joao; Matos, Bruno Ribeiro de; Ntais, Spyridon; Coral Fonseca, Fabio; Tavares, Ana C.

2013-01-01

Mg–Al hydrotalcite-like compounds with OH − ions intercalated in the gallery and modified with monobutylether ethylene glycol (mbeeg) were prepared from Mg 6 Al 2 (CO 3 )(OH) 16 ·4H 2 O by the reconstruction method. The effect of the ethylene glycol, a moderate surfactant, on the textural properties and on the vapor water sorption of the layered double hydroxides was investigated by transmission electron microscopy and nitrogen and water sorption techniques. The ion conductivity of the samples was measured at 98 % RH up to 180 °C. The compounds are formed by nanoplatelets with a lateral size inferior to 20 nm. The addition of the ethylene glycol was found to increase the specific surface area, total pore volume, and water sorption capacity of the Mg–Al layered double hydroxide. However, it also decreased the average pore diameter, and the ion conductivity of the ethylene glycol modified layered double hydroxide was lower than expected based on the samples’ specific surface area and water content.

Two actinide-organic frameworks constructed by a tripodal flexible ligand: Occurrence of infinite ((UO{sub 2})O{sub 2}(OH){sub 3}){sub 4n} and hexanuclear (Th{sub 6}O{sub 4}(OH){sub 4}) motifs

Energy Technology Data Exchange (ETDEWEB)

Liang, Lingling; Zhang, Ronglan [College of Chemistry and Materials, Shaanxi Key Laboratory of Physico-Inorganic Chemistry, Key Laboratory of Synthetic and Natural Functional Molecule Chemistry of Ministry of education, Northwest University, Xi’an 710069 (China); Zhao, Jianshe, E-mail: jszhao@nwu.edu.cn [College of Chemistry and Materials, Shaanxi Key Laboratory of Physico-Inorganic Chemistry, Key Laboratory of Synthetic and Natural Functional Molecule Chemistry of Ministry of education, Northwest University, Xi’an 710069 (China); Liu, Chiyang, E-mail: lcy@nwu.edu.cn [Department of Geology, Northwest University, Xi’an 710069 (China); Weng, Ng Seik [The University of Nottingham Malaysia Campus, 43500 Semenyih, Selangor Darul Ehsan (Malaysia)

2016-11-15

Two new actinide metal-organic frameworks were constructed by using a tripodal flexible ligand tris (2-carboxyethyl) isocyanurate (H{sub 3}tci) under hydrothermal condition. The combination of H{sub 3}tci and uranyl nitrate hexahydrate in aqueous solution leads to the isolation of [(UO{sub 2}){sub 2}(H{sub 2}O){sub 4}]{sub 0.5}(tci){sub 2}(UO{sub 2}){sub 4}(OH){sub 4}·18H{sub 2}O (1), which contains two distinct UO{sub 2}{sup 2+} coordination environments. Four uranyl cations, linked through μ{sub 3}-OH respectively, result in the edge-sharing ribbons. Then, the layer structure is constructed by U-O clusters linked through other eight-coordinated uranyl unions, giving rise to a porous structure in the space. Topological analysis reveals that complex 1 belongs to a (4, 8)-connected net with a schläfli symbol of (3{sup 4.}2{sup 6.}3){sub 2}(3{sup 4.}4{sup 6.}5{sup 6.}6{sup 8.}7{sup 3.}8). Th{sub 3}(tci){sub 2}O{sub 2}(OH){sub 2}(H{sub 2}O){sub 3}·12H{sub 2}O (2) generated by the reaction of H{sub 3}tci and thorium nitrate tetrahydrate, possesses nine-fold coodinated Th(IV) centers with a monocapped square antiprismatic geometry. The hexamers “Th{sub 6}O{sub 4}(OH){sub 4}” motifs are connected together by the carboxylate groups, showing a three-dimensional structures. Complex 2 takes on an 8-connected architecture and the point symbol is (4{sup 24.}6{sup 4}). - Graphical abstract: Two new 3D actinide metal-organic frameworks were constructed by using a tripodal flexible ligand tris (2-carboxyethyl) isocyanurate (H3tci) and their topological structures were displayed. The infinite ((UO{sub 2})O{sub 2}(OH){sub 3}){sub 4n} and hexanuclear (Th{sub 6}O{sub 4}(OH){sub 4}) motifs were found in the title actinides networks.

25-Hydroxyvitamin D (25(OH)D) and biomarkers of ovarian reserve.

Science.gov (United States)

Jukic, Anne Marie Z; Baird, Donna D; Wilcox, Allen J; Weinberg, Clarice R; Steiner, Anne Z

2018-07-01

The aim of the study was to examine the associations between 25-hydroxyvitamin D (25(OH)D) and biomarkers of ovarian reserve in a large community-based sample of women. In 2010 to 2016, women aged 30 to 44 years without any known fertility problems were recruited from the Chapel Hill, NC area for a prospective time-to-pregnancy cohort study. At enrollment 561 women provided a blood sample that was used to measure 25(OH)D, anti-Müllerian hormone (AMH), follicle-stimulating hormone, and inhibin-B. Unadjusted associations were estimated with Spearman correlation coefficients. Multivariable linear regression was used to estimate associations of 25(OH)D with ovarian reserve biomarkers, after adjusting for age, race, body mass index, smoking history, and recent use of hormonal birth control. The mean 25(OH)D was 36 ng/mL (SD = 11 ng/mL). 25(OH)D was not correlated with AMH, follicle-stimulating hormone, or inhibin-B (all r < 0.03). Multivariable results with continuous hormonal outcomes were also null. For dichotomous outcomes, there was a tendency for insufficient 25(OH)D (<30 ng/mL) to be associated with low AMH (<0.7 ng/mL) (odds ratio [95% CI]: 1.8 [0.9-4]). For the most part, 25(OH)D was not associated with ovarian reserve biomarkers in a group of women trying to become pregnant. We found some evidence that low 25(OH)D (<30 ng/mL) was associated with low AMH, but this should be confirmed in studies with a higher prevalence of low 25(OH)D.

Bukti Kebenaran Al-quran

OpenAIRE

Aliyah, Sri

2015-01-01

Al Quran is the greatest miracles of Muhammad SAW as the direction of humankind in order to reach eternal happiness. Scientific evidences show that Al Quran has the truth massages, although it was released far before the finding of modern sciences. The researches continue to study the truth of Al Quran an it revealed the historical fact.

Antidepressants differentially related to 1,25-(OH)(2) vitamin D(3) and 25-(OH) vitamin D(3) in late-life depression

NARCIS (Netherlands)

Oude Voshaar, R.C.; Derks, W.J.; Comijs, H.C.; Schoevers, R.A.; Borst, M.H. de; Marijnissen, R.M.

2014-01-01

A low plasma 25-OH vitamin D3 level is a universal risk factor for a wide range of diseases and has also been implicated in late-life depression. It is currently unknown whether the biologically active form of vitamin D, that is, 1,25-(OH)2 vitamin D3, is also decreased in late-life depression, or

Antidepressants differentially related to 1,25-(OH)(2) vitamin D-3 and 25-(OH) vitamin D-3 in late-life depression

NARCIS (Netherlands)

Oude Voshaar, R C; Derks, W J; Comijs, H C; Schoevers, R A; de Borst, M H; Marijnissen, R M

2014-01-01

A low plasma 25-OH vitamin D-3 level is a universal risk factor for a wide range of diseases and has also been implicated in late-life depression. It is currently unknown whether the biologically active form of vitamin D, that is, 1,25-(OH)(2) vitamin D-3, is also decreased in late-life depression,

Comparison of OH concentration measurements by DOAS and LIF during SAPHIR chamber experiments at high OH reactivity and low NO concentration

Directory of Open Access Journals (Sweden)

H. Fuchs

2012-07-01

Full Text Available During recent field campaigns, hydroxyl radical (OH concentrations that were measured by laser-induced fluorescence (LIF were up to a factor of ten larger than predicted by current chemical models for conditions of high OH reactivity and low NO concentration. These discrepancies, which were observed in forests and urban-influenced rural environments, are so far not entirely understood. In summer 2011, a series of experiments was carried out in the atmosphere simulation chamber SAPHIR in Jülich, Germany, in order to investigate the photochemical degradation of isoprene, methyl-vinyl ketone (MVK, methacrolein (MACR and aromatic compounds by OH. Conditions were similar to those experienced during the PRIDE-PRD2006 campaign in the Pearl River Delta (PRD, China, in 2006, where a large difference between OH measurements and model predictions was found. During experiments in SAPHIR, OH was simultaneously detected by two independent instruments: LIF and differential optical absorption spectroscopy (DOAS. Because DOAS is an inherently calibration-free technique, DOAS measurements are regarded as a reference standard. The comparison of the two techniques was used to investigate potential artifacts in the LIF measurements for PRD-like conditions of OH reactivities of 10 to 30 s⁻¹ and NO mixing ratios of 0.1 to 0.3 ppbv. The analysis of twenty experiment days shows good agreement. The linear regression of the combined data set (averaged to the DOAS time resolution, 2495 data points yields a slope of 1.02 ± 0.01 with an intercept of (0.10 ± 0.03 × 10⁶ cm⁻³ and a linear correlation coefficient of R² = 0.86. This indicates that the sensitivity of the LIF instrument is well-defined by its calibration procedure. No hints for artifacts are observed for isoprene, MACR, and different aromatic compounds. LIF measurements were approximately 30–40% (median larger than those by DOAS after MVK (20 ppbv and

Integration of OHS into Risk Management in an Open-Pit Mining Project in Quebec (Canada

Directory of Open Access Journals (Sweden)

Adel Badri

2011-09-01

Full Text Available Despite undeniable progress, the mining industry remains the scene of serious accidents revealing disregard for occupational health and safety (OHS and leaving open the debate regarding the safety of its employees. The San José mine last collapse near Copiapó, Chile on 5 August 2010 and the 69-day rescue operation that followed in order to save 33 miners trapped underground show the serious consequences of neglecting worker health and safety. The aim of this study was to validate a new approach to integrating OHS into risk management in the context of a new open-pit mining project in Quebec, based on analysis of incident and accident reports, semi-structured interviews, questionnaires and collaborative field observations. We propose a new concept, called hazard concentration, based on the number of hazards and their influence. This concept represents the weighted fraction of each category of hazards related to an undesirable event. The weight of each category of hazards is calculated by AHP, a multicriteria method. The proposed approach included the creation of an OHS database for facilitating expert risk management. Reinforcing effects between hazard categories were identified and all potential risks were prioritized. The results provided the company with a rational basis for choosing a suitable accident prevention strategy for its operational activities.

Physical properties of CO-dark molecular gas with C+ and OH observations

Science.gov (United States)

Tang, Ningyu; Li, Di; Heiles, Carl E.; ISM Group in National Astronomical Observatories, CAS

2017-01-01

The lifecycle of interstellar medium (ISM) is critical for understanding galaxy evolution. The transition between atomic neutral medium and dense molecular gas, however, cannot be traced adequately by either HI or CO emission. Results from dust observations of Planck all-sky mission and gamma-ray observations of Energetic Gamma Ray Experiment Telescope (EGRET) have revealed the existence of “CO dark molecular gas” (DMG) - molecular gas without CO emission. The physical conditions of DMG including density, temperature, and molecular composition are basis of understanding the ISM evolution. We analyzed physical properties of DMG with HI-self absorption and C+ fine line emission at 158 um toward the lines of sight of Galactic Observations of Terahertz C+ (GOTC+). DMG clouds have a median excitation temperature of 56 K and median volume density of 230 cm2, showing intermediate physical properties between atomic and molecular gas. Sixteen DMG clouds with high visual extinction (AV>=2.7 mag) were found. CO abundance compared to H2 in these clouds is two orders magnitude smaller than the cannonical value in the Milky Way and cannot be explained by the chemical evolutionary model. They may be formed through the agglomeration of pre-existing molecular gas in the Milky Way. We have finished a follow up survey of OH 18 cm lines toward 51 sightlines of GOTC+ including sightlines with DMG clouds through Arecibo telescope. DMG may result in the absence of correlation between CO and OH column density. A possible correlation was found between C+ and OH column density in tracing DMG.

Compressive performance and crack propagation in Al alloy/Ti{sub 2}AlC composites

Energy Technology Data Exchange (ETDEWEB)

Hanaor, D.A.H., E-mail: dorian.hanaor@sydney.edu.au [School of Civil Engineering, University of Sydney, Sydney, NSW 2006 (Australia); Hu, L. [Ames Laboratory, U.S. Department of Energy, Ames, Iowa 50011 (United States); Kan, W.H.; Proust, G. [School of Civil Engineering, University of Sydney, Sydney, NSW 2006 (Australia); Foley, M. [Australian Centre for Microscopy and Microanalysis, University of Sydney, Sydney, NSW 2006 (Australia); Karaman, I.; Radovic, M. [Department of Materials Science and Engineering, Texas A& M University, College Station, TX 77843 (United States)

2016-08-30

Composite materials comprising a porous Ti{sub 2}AlC matrix and Al 6061 alloy were fabricated by a current-activated pressure assisted melt infiltration process. Coarse, medium and fine meso-structures were prepared with Al alloy filled pores of differing sizes. Materials were subjected to uniaxial compressive loading up to stresses of 668 MPa, leading to the failure of specimens through crack propagation in both phases. As-fabricated and post-failure specimens were analysed by X-ray microscopy and electron microscopy. Quasi-static mechanical testing results revealed that compressive strength was the highest in the fine structured composite materials. While the coarse structured specimens exhibited a compressive strength of 80% relative to this. Reconstructed micro-scale X-ray tomography data revealed different crack propagation mechanisms. Large planar shear cracks propagated throughout the fine structured materials while the coarser specimens exhibited networks of branching cracks propagating preferentially along Al alloy-Ti{sub 2}AlC phase interfaces and through shrinkage pores in the Al alloy phase. Results suggest that control of porosity, compensation for Al alloy shrinkage and enhancement of the Al alloy-Ti{sub 2}AlC phase interfaces are key considerations in the design of high performance metal/Ti{sub 2}AlC phase composites.

Structural, vibrational and morphological properties of layered double hydroxides containing Ni{sup 2+}, Zn{sup 2+}, Al{sup 3+} and Zr{sup 4+} cations

Energy Technology Data Exchange (ETDEWEB)

Bezerra, Débora M. [Instituto de Química de São Carlos, Universidade de São Paulo, CP 780, CEP 13566-590 São Carlos, SP (Brazil); Rodrigues, João E.F.S. [Instituto de Física de São Carlos, Universidade de São Paulo, CP 780, CEP 13560-970 São Carlos, SP (Brazil); Assaf, Elisabete M., E-mail: eassaf@iqsc.usp.br [Instituto de Química de São Carlos, Universidade de São Paulo, CP 780, CEP 13566-590 São Carlos, SP (Brazil)

2017-03-15

Layered double hydroxides are anionic clays with formula [M{sup II}{sub 1−x} M{sup III}{sub x}(OH){sub 2}]{sup q+}[A{sup n−}]{sub q/n}·mH{sub 2}O, finding possible uses as catalyst support, adsorbents and so on. In this paper, we address the phase formation of layered double hydroxides containing Ni{sup 2+}, Zn{sup 2+}, Al{sup 3+} and Zr{sup 4+} cations, namely, NiZn-Al, NiZn-AlZr and NiZn-Zr compositions obtained by the coprecipitation method. Such systems were characterized by X-ray diffraction, confirming the phase formation for NiZn-Al and NiZn-AlZr samples. Infrared and Raman spectroscopies elucidated the anion and water molecules occurrence in the interlayer. Nitrogen physisorption (BET method) determined the presence of pores and specific surface area. The isotherm shapes were Type IV, according to the IUPAC, and represent a mesoporous structure. A morphological study was performed by means of scanning and transmission electron microscopies, and particle size values of 120, 131 and 235 nm for NiZn-Al, NiZn-AlZr and NiZn-Zr, respectively, were determined. Thermogravimetric analysis of the decomposition of the systems revealed that their complete disintegration occurred at ~ 450 °C and resulted in mixed oxides.

On OH production in water containing atmospheric pressure plasmas

NARCIS (Netherlands)

Bruggeman, P.J.; Schram, D.C.

2010-01-01

In this paper radical production in atmospheric pressure water containing plasmas is discussed. As OH is often an important radical in these discharges the paper focuses on OH production. Besides nanosecond pulsed coronas and diffusive glow discharges, several other atmospheric pressure plasmas

Differential and integral cross sections in OH(X) + Xe collisions

Energy Technology Data Exchange (ETDEWEB)

Sarma, Gautam; Saha, Ashim Kumar; Meulen, J. J. ter; Parker, David H., E-mail: parker@science.ru.nl [Institute for Molecules and Materials, Radboud University Nijmegen, Heijendaalseweg 135, 6525 ED Nijmegen (Netherlands); Marinakis, Sarantos, E-mail: s.marinakis@qmul.ac.uk [School of Biological and Chemical Sciences, Queen Mary University of London, Joseph Priestley Building, Mile End Road, London E1 4NS (United Kingdom)

2015-01-21

Differential cross sections (DCSs) for inelastic collisions of OH(X) with Xe have been measured at a collision energy of 483 cm{sup −1}. The hydroxyl (OH) radicals were initially prepared in the X{sup 2}Π{sub 3/2} (v = 0, j = 1.5, f) level using the hexapole electric field selection method. Products were detected state-selectively by [2 + 1] resonance-enhanced multiphoton ionization of OH, combined with velocity-map imaging. Integral cross sections in OH(X) + Xe at a collision energy of 490 cm{sup −1} were also measured by laser-induced fluorescence. The results are compared with exact close-coupling quantum mechanical scattering calculations on the only available ab initio potential energy surface (PES). The agreement between experimental and theoretical results is generally very satisfactory. This highlights the ability of such measurements to test the available PES for such a benchmark open-shell system. The agreement between experiment and theory for DCSs is less satisfactory at low scattering angles, and possible reasons for this disagreement are discussed. Finally, theoretical calculations of OH(X) + He DCSs have been obtained at various collision energies and are compared with those of OH(X) + Xe. The role of the reduced mass in the DCSs and partial cross sections is also examined.

Differential and integral cross sections in OH(X) + Xe collisions

International Nuclear Information System (INIS)

Sarma, Gautam; Saha, Ashim Kumar; Meulen, J. J. ter; Parker, David H.; Marinakis, Sarantos

2015-01-01

Differential cross sections (DCSs) for inelastic collisions of OH(X) with Xe have been measured at a collision energy of 483 cm −1 . The hydroxyl (OH) radicals were initially prepared in the X 2 Π 3/2 (v = 0, j = 1.5, f) level using the hexapole electric field selection method. Products were detected state-selectively by [2 + 1] resonance-enhanced multiphoton ionization of OH, combined with velocity-map imaging. Integral cross sections in OH(X) + Xe at a collision energy of 490 cm −1 were also measured by laser-induced fluorescence. The results are compared with exact close-coupling quantum mechanical scattering calculations on the only available ab initio potential energy surface (PES). The agreement between experimental and theoretical results is generally very satisfactory. This highlights the ability of such measurements to test the available PES for such a benchmark open-shell system. The agreement between experiment and theory for DCSs is less satisfactory at low scattering angles, and possible reasons for this disagreement are discussed. Finally, theoretical calculations of OH(X) + He DCSs have been obtained at various collision energies and are compared with those of OH(X) + Xe. The role of the reduced mass in the DCSs and partial cross sections is also examined

UNUSUAL SHOCK-EXCITED OH MASER EMISSION IN A YOUNG PLANETARY NEBULA

Energy Technology Data Exchange (ETDEWEB)

Qiao, Hai-Hua; Shen, Zhi-Qiang [Shanghai Astronomical Observatory, Chinese Academy of Sciences, 80 Nandan Rd, Shanghai, 200030 (China); Walsh, Andrew J. [International Centre for Radio Astronomy Research, Curtin University, GPO Box U1987, Perth WA 6845 (Australia); Gómez, José F. [Instituto de Astrofísica de Andalucía, CSIC, Glorieta de la Astronomía s/n, E-18008, Granada (Spain); Imai, Hiroshi [Department of Physics and Astronomy, Graduate School of Science and Engineering, Kagoshima University, 1-21-35 Korimoto, Kagoshima 890-0065 (Japan); Green, James A. [SKA Organisation, Jodrell Bank Observatory, Lower Withington, Macclesfield, Cheshire SK11 9DL (United Kingdom); Dawson, Joanne R. [Department of Physics and Astronomy and MQ Research Centre in Astronomy, Astrophysics and Astrophotonics, Macquarie University, NSW 2109 (Australia); Ellingsen, Simon P. [School of Physical Sciences, Private Bag 37, University of Tasmania, Hobart 7001, TAS (Australia); Breen, Shari L. [Australia Telescope National Facility, CSIRO Astronomy and Space Science, P.O. Box 76, Epping, NSW 1710 (Australia); Jones, Paul A.; Cunningham, Maria R. [School of Physics, University of New South Wales, Sydney, NSW 2052 (Australia); Gibson, Steven J., E-mail: haihua.qiao@curtin.edu.au [Department of Physics and Astronomy, Western Kentucky University, 1906 College Heights Blvd, Bowling Green, KY 42101 (United States)

2016-01-20

We report on OH maser emission toward G336.644−0.695 (IRAS 16333−4807), which is a H{sub 2}O maser-emitting Planetary Nebula (PN). We have detected 1612, 1667, and 1720 MHz OH masers at two epochs using the Australia Telescope Compact Array, hereby confirming it as the seventh known case of an OH-maser-emitting PN. This is only the second known PN showing 1720 MHz OH masers after K 3−35 and the only evolved stellar object with 1720 MHz OH masers as the strongest transition. This PN is one of a group of very young PNe. The 1612 MHz and 1667 MHz masers are at a similar velocity to the 22 GHz H{sub 2}O masers, whereas the 1720 MHz masers show a variable spectrum, with several components spread over a higher velocity range (up to 36 km s{sup −1}). We also detect Zeeman splitting in the 1720 MHz transition at two epochs (with field strengths of ∼2 to ∼10 mG), which suggests the OH emission at 1720 MHz is formed in a magnetized environment. These 1720 MHz OH masers may trace short-lived equatorial ejections during the formation of the PN.

Modelling atmospheric OH-reactivity in a boreal forest ecosystem

DEFF Research Database (Denmark)

Mogensen, D.; Smolander, S.; Sogachev, Andrey

2011-01-01

We have modelled the total atmospheric OH-reactivity in a boreal forest and investigated the individual contributions from gas phase inorganic species, isoprene, monoterpenes, and methane along with other important VOCs. Daily and seasonal variation in OH-reactivity for the year 2008 was examined...

Differential extraction of endogenous and exogenous 25-OH-vitamin D from serum makes the accurate quantification in liquid chromatography-tandem mass spectrometry assays challenging.

Science.gov (United States)

Lankes, Ulrich; Elder, Peter A; Lewis, John G; George, Peter

2015-01-01

Extraction followed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis is the method of choice when it comes to the accurate quantification of 25-OH-vitamin D in blood samples. It is generally assumed that the addition of exogenous internal standard allows for the determination of the endogenous analyte concentration. In this study we investigated the extraction properties of endogenous and exogenous 25-OH-vitamin D. Eight samples were used for the evaluation of the extraction procedure and 59 patients' samples for a method comparison. The methanol-to-sample ratio (v/v) and the sample-to-hexane ratio (v/v) were varied and the LC-MS/MS signals of endogenous 25-OH-vitamin D3, spiked 25-OH-vitamin D2 and internal standard of the extracts recorded. The optimized 'in-house' LC-MS/MS assay was compared to two automated chemiluminescence immunoassays from DiaSorin and Abbott. Mathematical analysis of the data revealed a differential extraction of endogenous 25-OH-vitamin D3, spiked 25-OH-vitamin D2 and non-equilibrated internal standard. Exogenous 25-OH-vitamin D can be measured accurately if a definite methanol-to-sample ratio is used. Endogenous 25-OH-vitamin D is affected by critical quantification issues due to a differential slope in the extraction profile. The actual 25-OH-vitamin D concentration can be one-third above the measured extractable concentration. Results confirm that the 'in-house' LC-MS/MS assay provides reproducible 25-OH-vitamin D results. Discordant concentrations of 25-OH-vitamin D from LC-MS/MS assays can be caused by selection of suboptimal extraction conditions. Furthermore, a different sample pretreatment or solvent extraction system may result in a different dissociation and extraction yield of endogenous 25-OH-vitamin D and therefore contribute to variations of LC-MS/MS results. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Theoretical perspectives on the mechanism and kinetics of the OH radical-initiated gas-phase oxidation of PCB126 in the atmosphere

International Nuclear Information System (INIS)

Dang, Juan; Shi, Xiangli; Zhang, Qingzhu; Wang, Wenxing

2015-01-01

Polychlorinated biphenyls (PCBs) primarily exist in the gas phase in air and may undergo atmospheric oxidation degradations, particularly the oxidation reaction initiated by OH radicals. In this work, the mechanism of the OH radical-initiated atmospheric oxidation of the most toxic PCB congener 3,3′,4,4′,5-pentachlorobiphenyl (PCB126) was investigated by using quantum chemistry methods. The rate constants of the crucial elementary reactions were estimated by the Rice–Ramsperger–Kassel–Marcus (RRKM) theory. The oxidation products of the reaction of PCB126 with OH radicals include 3,3′,4,4′,5-pentachlorobiphenyl-ols, chlorophenols, 2,3,4,7,8-pentachlorodibenzofuran, 2,3,4,6,7-pentachlorodibenzofuran, dialdehydes, 3,3′,4,4′,5-pentachloro-5′-nitro-biphenyl, and 4,5-dichloro-2-nitrophenol. Particularly, the formation of polychlorinated dibenzofurans (PCDFs) from the atmospheric oxidation of PCBs is revealed for the first time. The overall rate constant of the OH addition reaction is 2.52 × 10 −13 cm 3 molecule −1 s −1 at 298 K and 1 atm. The atmospheric lifetime of PCB126 determined by OH radicals is about 47.08 days which indicates that PCB126 can be transported long distances from local to global scales. - Highlights: • A comprehensive mechanism of OH-initiated oxidation of PCB126 was investigated. • The formation of PCDFs from the oxidation of PCBs is determined for the first time. • The rate constants for key elementary reactions were estimated by the RRKM theory. • The atmospheric lifetime of PCB126 determined by OH radicals is about 47.08 days

A new aluminium-hydrate species in hydrated Portland cements characterized by 27Al and 29Si MAS NMR spectroscopy

International Nuclear Information System (INIS)

Andersen, Morten Daugaard; Jakobsen, Hans J.; Skibsted, Jorgen

2006-01-01

Recent 27 Al MAS NMR studies of hydrated Portland cements and calcium-silicate-hydrate (C-S-H) phases have shown a resonance from Al in octahedral coordination, which cannot be assigned to the well-known aluminate species in hydrated Portland cements. This resonance, which exhibits the isotropic chemical shift δ iso = 5.0 ppm and the quadrupole product parameter P Q = 1.2 MHz, has been characterized in detail by 27 Al MAS and 27 Al{ 1 H} CP/MAS NMR for different hydrated white Portland cements and C-S-H phases. These experiments demonstrate that the resonance originates from an amorphous or disordered aluminate hydrate which contains Al(OH) 6 3- or O x Al(OH) 6-x (3+x)- units. The formation of the new aluminate hydrate is related to the formation of C-S-H at ambient temperatures, however, it decomposes by thermal treatment at temperatures of 70-90 o C. From the experiments in this work it is proposed that the new aluminate hydrate is either an amorphous/disordered aluminate hydroxide or a calcium aluminate hydrate, produced as a separate phase or as a nanostructured surface precipitate on the C-S-H phase. Finally, the possibilities of Al 3+ for Ca 2+ substitution in the principal layers and interlayers of the C-S-H structure are discussed

MicroRNA Profiling Reveals Marker of Motor Neuron Disease in ALS Models.

Science.gov (United States)

Hoye, Mariah L; Koval, Erica D; Wegener, Amy J; Hyman, Theodore S; Yang, Chengran; O'Brien, David R; Miller, Rebecca L; Cole, Tracy; Schoch, Kathleen M; Shen, Tao; Kunikata, Tomonori; Richard, Jean-Philippe; Gutmann, David H; Maragakis, Nicholas J; Kordasiewicz, Holly B; Dougherty, Joseph D; Miller, Timothy M

2017-05-31

Amyotrophic lateral sclerosis (ALS) is a progressive neurodegenerative disorder marked by the loss of motor neurons (MNs) in the brain and spinal cord, leading to fatally debilitating weakness. Because this disease predominantly affects MNs, we aimed to characterize the distinct expression profile of that cell type to elucidate underlying disease mechanisms and to identify novel targets that inform on MN health during ALS disease time course. microRNAs (miRNAs) are short, noncoding RNAs that can shape the expression profile of a cell and thus often exhibit cell-type-enriched expression. To determine MN-enriched miRNA expression, we used Cre recombinase-dependent miRNA tagging and affinity purification in mice. By defining the in vivo miRNA expression of MNs, all neurons, astrocytes, and microglia, we then focused on MN-enriched miRNAs via a comparative analysis and found that they may functionally distinguish MNs postnatally from other spinal neurons. Characterizing the levels of the MN-enriched miRNAs in CSF harvested from ALS models of MN disease demonstrated that one miRNA (miR-218) tracked with MN loss and was responsive to an ALS therapy in rodent models. Therefore, we have used cellular expression profiling tools to define the distinct miRNA expression of MNs, which is likely to enrich future studies of MN disease. This approach enabled the development of a novel, drug-responsive marker of MN disease in ALS rodents. SIGNIFICANCE STATEMENT Amyotrophic lateral sclerosis (ALS) is a neurodegenerative disease in which motor neurons (MNs) in the brain and spinal cord are selectively lost. To develop tools to aid in our understanding of the distinct expression profiles of MNs and, ultimately, to monitor MN disease progression, we identified small regulatory microRNAs (miRNAs) that were highly enriched or exclusive in MNs. The signal for one of these MN-enriched miRNAs is detectable in spinal tap biofluid from an ALS rat model, where its levels change as disease

Nanosized yolk–shell Fe{sub 3}O{sub 4}@Zr(OH){sub x} spheres for efficient removal of Pb(II) from aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Pan, Shunlong [Jiangsu Key Laboratory of Chemical Pollution Control and Resources Reuse, School of Environmental and Biological Engineering, Nanjing University of Science and Technology, Nanjing 210094 (China); Li, Jiansheng, E-mail: lijsh@mail.njust.edu.cn [Jiangsu Key Laboratory of Chemical Pollution Control and Resources Reuse, School of Environmental and Biological Engineering, Nanjing University of Science and Technology, Nanjing 210094 (China); Wan, Gaojie; Liu, Chao [Jiangsu Key Laboratory of Chemical Pollution Control and Resources Reuse, School of Environmental and Biological Engineering, Nanjing University of Science and Technology, Nanjing 210094 (China); Fan, Wenhong, E-mail: fanwh@buaa.edu.cn [Department of Environmental Science and Engineering, School of Chemistry and Environment, Beihang University, Beijing 100191 (China); Wang, Lianjun, E-mail: wanglj@mail.njust.edu.cn [Jiangsu Key Laboratory of Chemical Pollution Control and Resources Reuse, School of Environmental and Biological Engineering, Nanjing University of Science and Technology, Nanjing 210094 (China)

2016-05-15

Highlights: • Well dispersed and easy separated nanoadsorbents with stable chemical property are highly desired. • Fe{sub 3}O{sub 4}@Zr(OH){sub x} yolk–shell nanospheres (YSNs) nanoadsorbents were prepared. • Enhanced Pb(II) adsorption capacity of 310.8 mg/g was achieved on Fe{sub 3}O{sub 4}@Zr(OH){sub x} YSNs based on Zr weight. • The cavities in Fe{sub 3}O{sub 4}@Zr(OH){sub x} YSNs is responsible for the improved performance. - Abstract: In this work, Fe{sub 3}O{sub 4}@Zr(OH){sub x} yolk–shell nanospheres (YSNs) were synthesized via a two-step process and further examined as adsorbents for the removal of Pb(II). To understand the hollow structure on the adsorption properties of Pb(II), another adsorbent without hollow cavities, i.e., Fe{sub 3}O{sub 4}@SiO{sub 2}@Zr(OH){sub x} core–shell nanospheres (CSNs), was also prepared for comparison. The adsorption results showed that Fe{sub 3}O{sub 4}@Zr(OH){sub x} YSNs exhibited 41.6% higher Pb(II) adsorption capacity as compared to that of Fe{sub 3}O{sub 4}@SiO{sub 2}@Zr(OH){sub x} CSNs. The isotherm was well fitted to Langmuir adsorption model with q{sub max} value of 310.8 mg/g after normalized by the weight of Zr in Fe{sub 3}O{sub 4}@Zr(OH){sub x} YSNs. Scanning transmission electron microscopy (STEM) mapping results revealed that the existence of cavities between Fe{sub 3}O{sub 4} cores and Zr(OH){sub x} shells is responsible for the improved adsorption performance. XPS analysis indicated the surface hydroxyl groups played a key role in the Pb(II) adsorption. The removal efficiency of Pb(II) was maintained above 90% in five consecutive adsorption–desorption cycles.

Enhanced WWTP effluent organic matter removal in hybrid ozonation-coagulation (HOC) process catalyzed by Al-based coagulant

Energy Technology Data Exchange (ETDEWEB)

Jin, Xin [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an, Shaanxi Province, 710055 (China); Jin, Pengkang, E-mail: pkjin@hotmail.com [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an, Shaanxi Province, 710055 (China); Hou, Rui [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an, Shaanxi Province, 710055 (China); Yang, Lei [Department of Materials Science and Engineering, Monash University, Clayton, VIC, 3800 (Australia); Wang, Xiaochang C., E-mail: xcwang@xauat.edu.cn [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an, Shaanxi Province, 710055 (China)

2017-04-05

Highlights: • A novel HOC process was firstly put forward to apply in wastewater reclamation. • Interactions between ozone and Al-based coagulants was found in the HOC process. • Ozonation can be catalyzed and enhanced by Al-based coagulants in the HOC process. • HOC process showed better organics removal than pre-ozonation-coagulation process. - Abstract: A novel hybrid ozonation-coagulation (HOC) process was developed for application in wastewater reclamation. In this process, ozonation and coagulation occurred simultaneously within a single unit. Compared with the conventional pre-ozonation-coagulation process, the HOC process exhibited much better performance in removing dissolved organic matters. In particular, the maximal organic matters removal efficiency was obtained at the ozone dosage of 1 mgO{sub 3}/mg DOC at each pH value (pH 5, 7 and 9). In order to interpret the mechanism of the HOC process, ozone decomposition was monitored. The results indicated that ozone decomposed much faster in the HOC process. Moreover, by using the reagent of O{sub 3}-resistant hydroxyl radical (·OH) probe compound, para-chlorobenzoic acid (pCBA), and electron paramagnetic resonance (EPR) analysis, it was observed that the HOC process generated higher content of ·OH compared with pre-ozonation process. This indicates that the ·OH oxidation reaction as the key step can be catalyzed and enhanced by Al-based coagulants and their hydrolyzed products in this developed process. Thus, based on the catalytic effects of Al-based coagulants on ozonation, the HOC process provides a promising alternative to the conventional technology for wastewater reclamation in terms of higher efficiency.

Effect of Zr on the Corrosion Properties of Mg-Li-Al Alloy

International Nuclear Information System (INIS)

Kim, Soon Ho; Choi, Sang Hyun; Kim, In Bae; Kim, Kyung Hyun

1994-01-01

Effect of Zr on the electrochemical corrosion characteristics of Mg-Li-Al alloy has been investigated by means of potentiodynamic polarization study. The electrochemical behaviors were evaluated in 0.03% NaCl solution and the solution buffered with KH 2 PO 5 · NaOH at room temperature. It was found that the addition of very small quantity of Zr (0.03wt%) in Mg-Li-Al alloy increased corrosion rates and amount of corrosion products and decreased the pitting resistance of the alloy. From the results it was concluded that Zr which is added to increase the strength of Mg-Li-Al alloy is harmful to corrosion properties of the alloy

Antitumor activity of ginseng sapogenins, 25-OH-PPD and 25-OCH3-PPD, on gastric cancer cells.

Science.gov (United States)

Zhao, Chen; Su, Guangyue; Wang, Xude; Zhang, Xiaoshu; Guo, Shuang; Zhao, Yuqing

2016-01-01

25-Hydroxyprotopanaxadiol (25-OH-PPD) and 25-methoxylprotopanaxadiol (25-OCH3-PPD), two ginseng sapogenins, have potent antitumor activity and their effects on gastric cancer (BGC-823, SGC-7901, MKN-28) cells and a gastric mucosa (GES-1) cell line are reported. Both compounds significantly inhibited the growth of gastric cancer cells, while having lesser inhibitory effects on GES-1 cells by MTT assay. A mechanistic study revealed that the two ginseng sapogenins could induce apoptosis in BGC-823 cells by morphological observation, DNA fragmentation, flow cytometry and western blot analysis. Besides, the apoptosis was inhibited by Ac-DEVD-CHO, a caspase 3 inhibitor, which was confirmed by cell viability analysis. These results indicate that 25-OH-PPD and 25-OCH3-PPD have potential to be promising agents for the treatment of gastric cancer.

Serum 25(OH)D seasonality in urologic patients from central Italy.

Science.gov (United States)

Calgani, Alessia; Iarlori, Marco; Rizi, Vincenzo; Pace, Gianna; Bologna, Mauro; Vicentini, Carlo; Angelucci, Adriano

2016-09-01

Hypovitaminosis D is increasingly recognized as a cofactor in several diseases. In addition to bone homeostasis, vitamin D status influences immune system, muscle activity and cell differentiation in different tissues. Vitamin D is produced in the skin upon exposure to UVB rays, and sufficient levels of serum 25(OH)D are dependent mostly on adequate sun exposure, and then on specific physiologic variables, including skin type, age and Body Mass Index (BMI). In contrast with common belief, epidemiologic data are demonstrating that hypovitaminosis D must be a clinical concern not only in northern Countries. In our study, we investigated vitamin D status in a male population enrolled in a urology clinic of central Italy. In addition, we evaluated the correlation between vitamin D status and UVB irradiance measured in our region. The two principal pathologies in the 95 enrolled patients (mean age 66years) were benign prostate hypertrophy and prostate carcinoma. >50% of patients had serum 25(OH)D values in the deficient range (pyranometer in our region (Abruzzo, central Italy) revealed a large difference during the year, with winter months characterized by an UV irradiance about tenfold lower than summer months. Then we applied a mathematical model in order to evaluate the expected vitamin D production according to the standard erythemal dose measured in the different seasons. In winter months, the low available UVB radiation and the small exposed skin area resulted not sufficient to obtain the recommended serum doses of vitamin D. Although in summer months UVB irradiance was largely in excess to produce vitamin D in the skin, serum vitamin D resulted sufficient in September only in those patients who declared an outdoor time of at least 3h per day in the previous summer. In conclusion, hypovitaminosis D is largely represented in elderly persons in our region. Seasonal fluctuation in serum 25(OH)D was explained by a reduced availability of UVB in winter and by

Precursor preparation for Ca-Al layered double hydroxide to remove hexavalent chromium coexisting with calcium and magnesium chlorides

Science.gov (United States)

Zhong, Lihua; He, Xiaoman; Qu, Jun; Li, Xuewei; Lei, Zhiwu; Zhang, Qiwu; Liu, Xinzhong

2017-01-01

Al(OH)3 and Ca(OH)2 powders are co-ground to prepare a precursor which hydrates into a layered double hydroxide (LDH) phase by agitation in aqueous solution with target hexavalent chromium (Cr(VI)) at room temperature, to achieve an obvious improvement in removal efficiency of Cr(VI) through an easy incorporation into the structure. Although the prepared precursor transforms into LDH phases also when agitated in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist. The adsorption isotherm and kinetic studies show that the phenomena occurring on the Al-Ca precursor fit a pseudo-second-order kinetics with a Langmuir adsorption capacity of 59.45 mg/g. Besides, characterizations of the prepared precursor and the samples after adsorption are also performed by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Transmission electron microscope (TEM) to understand the reason of the preferential incorporation of Cr(VI) to the coexisting chloride salts during the LDH phase formation. Ca-Al precursor (C3A) was agitated in a hexavalent chromium (Cr(VI)) solution to form Al-Ca-CrO4 LDH product. Ca-Al-CrO4 LDH phase occurred preferentially to Ca-Al-MCl2 LDH phases in the solutions of calcium and magnesium chlorides, it incorporates Cr(VI) preferentially to the chloride salts when they coexist.

New investigation on THz spectra of OH and SH radicals (X∏)

Science.gov (United States)

Martin-Drumel, M. A.; Eliet, S.; Pirali, O.; Guinet, M.; Hindle, F.; Mouret, G.; Cuisset, A.

2012-10-01

Pure rotational transitions of OH and SH radicals have been recorded in the THz spectral range using cw-THz and synchrotron-based FT-FIR techniques. Line lists on these radicals have been completed in the three and two lowest vibrational states for OH and SH, respectively. Furthermore, the hyperfine structure of OH and SH has been observed for the first time using infrared IR FT-spectroscopy, and at frequencies higher than 1 THz, respectively. A combined fit has been made for each of these radicals including v = 0, 1 and 2 for OH and v = 0 and 1 for SH.

Synthesis, characterization and flocculation activity of novel Fe(OH){sub 3}-polyacrylamide hybrid polymer

Energy Technology Data Exchange (ETDEWEB)

Wang Huilong; Cui Jinyan [Department of Chemistry, Dalian University of Technology, Dalian 116023 (China); Jiang Wenfeng, E-mail: dlutjiangwf@yahoo.com.cn [Department of Chemistry, Dalian University of Technology, Dalian 116023 (China)

2011-11-01

Highlights: {yields} The preparation of a novel Fe(OH){sub 3}-PAM hybrid polymer flocculant is achieved via free radical solution polymerization. {yields} Flocculation of kaolin suspensions using this novel Fe(OH){sub 3}-PAM hybrid polymer flocculant is revealed in this study. {yields} The statistical model was first applied for calculating the thermodynamic parameters for the kaolin flocculating process. - Abstract: A novel Fe(OH){sub 3}-polyacrylamide inorganic-organic hybrid polymer (FHPAM) was synthesized via free radical solution polymerization initiated by a redox initiation system ((NH{sub 4}){sub 2}S{sub 2}O{sub 8}-NaHSO{sub 3}) in an aqueous medium. Reaction parameters influencing the intrinsic viscosity and the yield of the hybrid polymer, such as initiator concentration, monomer mass fraction, temperature and reaction time were investigated and optimized. The results show that the maximum intrinsic viscosity and up to 94% yields of the hybrid polymer can be achieved using initiator concentration of 0.3% with acrylamide monomer mass fraction of 20% under solution polymerization at 40 deg. C for 7 h. The physicochemical properties of this hybrid flocculant were characterized with TEM, FTIR spectra, TGA, and conductivity. It was found that a chemical bond exists between Fe(OH){sub 3} colloid and polyacrylamide chains in the FHPAM. The application of the hybrid polymer for the treatment of 2.5 g L{sup -1} kaolin suspension indicates that it had an excellent flocculation capacity and its flocculation efficiency was much better than that of commercial available polyacrylamide (PAM) and polymeric ferric sulfate (PFS). The optimal conditions for the flocculation treatment of kaolin suspension were the FHPAM dosage of 40 mg L{sup -1} at pH 7.0. The thermodynamic parameters for the flocculation process were calculated based on a statistical model. Interpretation of the results was given.

Emission of OH* and CO2* during the high-temperature oxidation of acetone in reflected shock waves

Science.gov (United States)

Tereza, A. M.; Smirnov, V. N.; Vlasov, P. A.; Shumova, V. V.; Garmash, A. A.

2018-01-01

Experimental and kinetic modeling study of the ignition of a stoichiometric mixture of acetone with oxygen diluted by argon was carried out behind reflected shock waves within the temperature range of 1350-1810 K for the total mixture concentration [M 50] ~ 10-5 mol/cm3. Emission signals were recorded simultaneously for three different wavelengths: OH* (λ = 308 nm) and {{{CO}}}2* (λ1 = 365 nm; λ2 = 451 nm). It was revealed that the time it takes to reach the maximum of emission of OH* and {{{CO}}}2* is practically the same over the whole temperature range. At the same time, the emission profiles of {{{CO}}}2* after the maximum was attained, recorded at λ2 = 451 nm, differ noticeably from the profiles recorded at λ1 = 365 nm. For numerical modeling of the emission profiles of OH* and {{{CO}}}2* , the corresponding sets of excitation and quenching reactions available in the literature were used. In the course of our numerical simulations we succeeded in good agreement of our own experimental and simulation results on acetone ignition and the results available in the literature for conditions under consideration.

Atmospheric chemistry of CF3CH2CH2OH

DEFF Research Database (Denmark)

Hurley, Michael D.; Misner, Jessica A.; Ball, James C.

2005-01-01

Relative rate techniques were used to study the kinetics of the reactions of Cl atoms and OH radicals with CF3CH2C(O)H and CF3CH2CH2OH in 700 Torr of N-2 or air diluent at 296 2 K. The rate constants determined were k(Cl+CF3CH2C(O)H) = (1.81 +/- 0.27) x 10(-11), k(OH+CF3CH2C(O)H) = (2.57 +/- 0.44...

Direct observation of unimolecular decay of CH{sub 3}CH{sub 2}CHOO Criegee intermediates to OH radical products

Energy Technology Data Exchange (ETDEWEB)

Fang, Yi; Liu, Fang; Lester, Marsha I., E-mail: milester@sas.upenn.edu [Department of Chemistry, University of Pennsylvania, Philadelphia, Pennsylvania 19104-6323 (United States); Klippenstein, Stephen J. [Chemical Sciences and Engineering Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States)

2016-07-28

The unimolecular decay of carbonyl oxide intermediates, known as Criegee intermediates, produced in alkene ozonolysis is a significant source of OH radicals in the troposphere. Here, the rate of appearance of OH radical products is examined directly in the time-domain for a prototypical alkyl-substituted Criegee intermediate, CH{sub 3}CH{sub 2}CHOO, following vibrational activation under collision-free conditions. Complementary statistical Rice–Ramsperger–Kassel–Marcus calculations of the microcanonical unimolecular decay rate for CH{sub 3}CH{sub 2}CHOO are also carried out at energies in the vicinity of the barrier for 1,4 hydrogen atom transfer that leads to OH products. Tunneling through the barrier, derived from high level electronic structure calculations, contributes significantly to the decay rate. Infrared transitions of CH{sub 3}CH{sub 2}CHOO are identified in the CH stretch overtone region, which are detected by ultraviolet laser-induced fluorescence of the resultant OH products. The features observed are attributed to CH vibrational excitations and conformational forms utilizing insights from theory. Both experiment and theory yield unimolecular decay rates for CH{sub 3}CH{sub 2}CHOO of ca. 10{sup 7} s{sup −1}, which are slower than those obtained for syn-CH{sub 3}CHOO or (CH{sub 3}){sub 2}COO reported previously [Fang et al., J. Chem. Phys. 144, 061102 (2016)] at similar energies. Master equation modeling is also utilized to predict the thermal decay rate of CH{sub 3}CH{sub 2}CHOO under atmospheric conditions, giving a rate of 279 s{sup −1} at 298 K.

ENHANCEMENT OF ACIDITY AND CATALYTIC ACTIVITY OF ALUMINA BASED METAL ORGANIC FRAMEWORK (MIL-53 Al)

OpenAIRE

Yilmaz, Esra; Sert, Emine; Atalay, Ferhan Sami

2017-01-01

Metal organic frameworks are highly porous materials which are formed bycombination of metal precursor and salts as inorganic part and ligand asorganic part. They have many advantages such as low density, high surface area,tunable pore size and high porosity. Due to peculiar features, such asunsaturated metal active sites, high surface area and easily functionalization,its usage as catalyst are promising.  The MIL-53(Al) structure contains chains of transcorner-sharing [AlO4(OH)2] oc...

Room temperature chemical synthesis of Cu(OH)2 thin films for supercapacitor application

International Nuclear Information System (INIS)

Gurav, K.V.; Patil, U.M.; Shin, S.W.; Agawane, G.L.; Suryawanshi, M.P.; Pawar, S.M.; Patil, P.S.; Lokhande, C.D.; Kim, J.H.

2013-01-01

Highlights: •Cu(OH) 2 is presented as the new supercapacitive material. •The novel room temperature method used for the synthesis of Cu(OH) 2 . •The hydrous, nanograined Cu(OH) 2 shows higher specific capacitance of 120 F/g. -- Abstract: Room temperature soft chemical synthesis route is used to grow nanograined copper hydroxide [Cu(OH) 2 ] thin films on glass and stainless steel substrates. The structural, morphological, optical and wettability properties of Cu(OH) 2 thin films are studied by means of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), UV–vis spectrophotometer and water contact angle measurement techniques. The results showed that, room temperature chemical synthesis route allows to form the nanograined and hydrophilic Cu(OH) 2 thin films with optical band gap energy of 3.0 eV. The electrochemical properties of Cu(OH) 2 thin films are studied in an aqueous 1 M NaOH electrolyte using cyclic voltammetry. The sample exhibited supercapacitive behavior with 120 F/g specific capacitance

Where is OH and Does It Trace the Dark Molecular Gas (DMG)?

Science.gov (United States)

Li, Di; Tang, Ningyu; Nguyen, Hiep; Dawson, J. R.; Heiles, Carl; Xu, Duo; Pan, Zhichen; Goldsmith, Paul F.; Gibson, Steven J.; Murray, Claire E.; Robishaw, Tim; McClure-Griffiths, N. M.; Dickey, John; Pineda, Jorge; Stanimirović, Snežana; Bronfman, L.; Troland, Thomas; PRIMO Collaboration

2018-03-01

Hydroxyl (OH) is expected to be abundant in diffuse interstellar molecular gas because it forms along with H2 under similar conditions and forms within a similar extinction range. We have analyzed absorption measurements of OH at 1665 MHz and 1667 MHz toward 44 extragalactic continuum sources, together with the J = 1–0 transitions of 12CO, 13CO, and C18O, and the J = 2–1 transition of 12CO. The excitation temperatures of OH were found to follow a modified lognormal distribution f({T}ex})\\propto \\tfrac{1}{\\sqrt{2π }σ }\\exp ≤ft[-\\tfrac{{[{ln}({T}ex})-{ln}(3.4{{K}})]}2}{2{σ }2}\\right], the peak of which is close to the temperature of the Galactic emission background (CMB+synchrotron). In fact, 90% of the OH has excitation temperatures within 2 K of the Galactic background at the same location, providing a plausible explanation for the apparent difficulty of mapping this abundant molecule in emission. The opacities of OH were found to be small and to peak around 0.01. For gas at intermediate extinctions (AV ∼ 0.05–2 mag), the detection rate of OH with a detection limit N(OH) ≃ 1012 cm‑2 is approximately independent of AV. We conclude that OH is abundant in the diffuse molecular gas and OH absorption is a good tracer of “dark molecular gas (DMG).” The measured fraction of DMG depends on the assumed detection threshold of the CO data set. The next generation of highly sensitive low-frequency radio telescopes, such as FAST and SKA, will make feasible the systematic inventory of diffuse molecular gas through decomposing, in velocity, the molecular (e.g., OH and CH) absorption profiles toward background continuum sources with numbers exceeding what is currently available by orders of magnitude.

Reduction Mechanisms of Cu2+-Doped Na2O-Al2O3-SiO2 Glasses during Heating in H2 Gas.

Science.gov (United States)

Nogami, Masayuki; Quang, Vu Xuan; Ohki, Shinobu; Deguchi, Kenzo; Shimizu, Tadashi

2018-01-25

Controlling valence state of metal ions that are doped in materials has been widely applied for turning optical properties. Even though hydrogen has been proven effective to reduce metal ions because of its strong reducing capability, few comprehensive studies focus on practical applications because of the low diffusion rate of hydrogen in solids and the limited reaction near sample surfaces. Here, we investigated the reactions of hydrogen with Cu 2+ -doped Na 2 O-Al 2 O 3 -SiO 2 glass and found that a completely different reduction from results reported so far occurs, which is dominated by the Al/Na concentration ratio. For Al/Na glass body. For Al/Na > 1, on the other hand, the reduction of Cu 2+ ions occurred simultaneously with the formation of OH bonds, whereas the reduced Cu metal moved outward and formed a metallic film on glass surface. The NMR and Fourier transform infrared results indicated that the Cu 2+ ions were surrounded by Al 3+ ions that formed AlO 4 , distorted AlO 4 , and AlO 5 units. The diffused H 2 gas reacted with the Al-O - ···Cu + units, forming Al-OH and metallic Cu, the latter of which moved freely toward glass surface and in return enhanced H 2 diffusion.

Dynamics of Intercalation/De-Intercalation of Rhodamine B during the Polymorphic Transformation of CdAl Layered Double Hydroxide to the Brucite-Like Cadmium Hydroxide

KAUST Repository

Saliba, Daniel

2016-06-23

Cadmium-Aluminum layered double hydroxide (CdAl LDH) is thermodynamically unstable and transforms to Cd(OH)2 and Al(OH)3 in a short period of time. We present a reaction-diffusion framework that enables us to use in situ steady-state fluorescence spectroscopy to study the kinetics of intercalation of a fluorescent probe (Rhodamine B (RhB)) during the formation of the CdAl LDH and its de-intercalation upon the conversion of the LDH phase to the β phase (Cd(OH)2). The method involves the diffusion of sodium hydroxide into a hydrogel gel matrix containing the aluminum and cadmium ions as well as the species we wish to incorporate in the interlayers of the LDH. The existence of RhB between the LDH layers and its expel during the transition into the β phase are proved via fluorescence microscopy, XRD and ssNMR. The activation energies of intercalation and de-intercalation of RhB are computed and show dependence on the cationic ratio of the corresponding LDH. We find that the energies of de- intercalation are systematically higher than those of intercalation proving that the dyes are stabilized due to the probe-brucite sheets interactions.

Dynamics of Intercalation/De-Intercalation of Rhodamine B during the Polymorphic Transformation of CdAl Layered Double Hydroxide to the Brucite-Like Cadmium Hydroxide

KAUST Repository

Saliba, Daniel; Ezzeddine, Alaa; Emwas, Abdul-Hamid M.; Khashab, Niveen M.; Al-Ghoul, Mazen

2016-01-01

Cadmium-Aluminum layered double hydroxide (CdAl LDH) is thermodynamically unstable and transforms to Cd(OH)2 and Al(OH)3 in a short period of time. We present a reaction-diffusion framework that enables us to use in situ steady-state fluorescence spectroscopy to study the kinetics of intercalation of a fluorescent probe (Rhodamine B (RhB)) during the formation of the CdAl LDH and its de-intercalation upon the conversion of the LDH phase to the β phase (Cd(OH)2). The method involves the diffusion of sodium hydroxide into a hydrogel gel matrix containing the aluminum and cadmium ions as well as the species we wish to incorporate in the interlayers of the LDH. The existence of RhB between the LDH layers and its expel during the transition into the β phase are proved via fluorescence microscopy, XRD and ssNMR. The activation energies of intercalation and de-intercalation of RhB are computed and show dependence on the cationic ratio of the corresponding LDH. We find that the energies of de- intercalation are systematically higher than those of intercalation proving that the dyes are stabilized due to the probe-brucite sheets interactions.

Penurunan Kromium (Cr dalam Limbah Cair Proses Penyamakan Kulit Menggunakan Senyawa Alkali Ca(OH2, NaOH, dan NaHCO3 (Studi Kasus di Pt Trimulyo Kencana Mas Semarang

Directory of Open Access Journals (Sweden)

Tri Joko

2015-12-01

Full Text Available ABTRACT Background : One of the industrial type which use hazardous materials in its production process is leather tanning industry, by using chromium compound (Cr. Chromium is a heavy metal compound which recognized has a high poison energy. Result of analysis of sampel industrial liquid waste of leather tanning of PT Trimulyo Kencana Mas (TKM Semarang showed that total chromium concervation was 49,575 m/l. This total Chromium rate was still above the standard quality of which enabled maximal 2,0 mg/l, according to Kep51/MENLH/110/1995. Alkali compound of Ca(OH2, NaOH and NaHC03 is chemicals able to be used for the processing of industrial liquid waste of pregnant leather tanning of chromium, functioning to boost up condensation pH andprecipitated chromium so that obtained chrome in theform of hydroxide chromium (Cr(OH3. Methods : which used in this research is (quasi experimental, with experiment variable repeated or referred as one group pretest ‑ posttest design. Results : of this research showed that optimum pH for the compound of each alkali at condition of pH 8, with the efficiency dissociation of chromium was equal to 99,28 % by using alkali compound of Ca(OH2 and of NaOH, while usage of NaHC03 equal to 98,50 %. Conclusions: Alkali compound of Ca(OH2, NaOH and NaHCO3 can degrade chromium concentration (Cr in liquid waste with high efficiency, that is reaching under standard quality. The most effective Compound of Alkali, evaluated from the technical aspect for the degradation of chromium concentration in liquid waste is NaOH, because with only small dose can dissociate chromium in liquid waste with high efficiency (99,28 %, For economic reason and recommendation for application in the field is Ca(OH2. Keyword : Efficiency Ca(OH2,, hydroxide chromium, NaHCO3, NaOH, pH, Chromium Compound

Corrosion behavior of die-cast Mg-4Al-2Sn-xCa alloy

Energy Technology Data Exchange (ETDEWEB)

Park, Kyung Chul; Kim, Byeong Ho; Kim, Kyung Ro [Defence Agency for Technology and Quality, Jinju (Korea, Republic of); Cho, Dae Hyun; Park, Ik Min [Pusan National University, Busan (Korea, Republic of)

2016-05-15

In the present work, the effect of Ca additions on microstructure and corrosion characteristics of high pressure die-cast Mg-4Al-2Sn alloy has been investigated. Mg-4Al-2Sn-xCa (x= 0, 0.3 and 0.7wt.%) alloy was prepared by using a high pressure die-casting method. Results indicated that the microstructure of Mg-4Al-2Sn alloy consisted of α-Mg, Mg{sub 17}Al{sub 12} and Mg{sub 2}Sn phase. With increase of Ca additions, CaMgSn phase was newly formed and grain size was sharply decreased. From the test results, the corrosion resistance of die-cast Mg-4Al-2Sn alloy was significantly improved by Ca addition. It is considered that stabilization of Mg(OH){sub 2} layer and refinements of microstructure with increase of Ca additions.

The adsorption features between insecticidal crystal protein and nano-Mg(OH)2.

Science.gov (United States)

Pan, Xiaohong; Xu, Zhangyan; Zheng, Yilin; Huang, Tengzhou; Li, Lan; Chen, Zhi; Rao, Wenhua; Chen, Saili; Hong, Xianxian; Guan, Xiong

2017-12-01

Nano-Mg(OH) 2 , with low biological toxicity, is an ideal nano-carrier for insecticidal protein to improve the bioactivity. In this work, the adsorption features of insecticidal protein by nano-Mg(OH) 2 have been studied. The adsorption capacity could reach as high as 136 mg g -1 , and the adsorption isotherm had been fitted with Langmuir and Freundlich models. Moreover, the adsorption kinetics followed a pseudo-first or -second order rate model, and the adsorption was spontaneous and an exothermic process. However, high temperatures are not suitable for adsorption, which implies that the temperature would be a critical factor during the adsorption process. In addition, FT-IR confirmed that the protein was adsorbed on the nano-Mg(OH) 2 , zeta potential analysis suggested that insecticidal protein was loaded onto the nano-Mg(OH) 2 not by electrostatic adsorption but maybe by intermolecular forces, and circular dichroism spectroscopy of Cry11Aa protein before and after loading with nano-Mg(OH) 2 was changed. The study applied the adsorption information between Cry11Aa and nano-Mg(OH) 2 , which would be useful in the practical application of nano-Mg(OH) 2 as a nano-carrier.

Characterization of plasma-induced cell membrane permeabilization: focus on OH radical distribution

International Nuclear Information System (INIS)

Sasaki, Shota; Honda, Ryosuke; Hokari, Yutaro; Takashima, Keisuke; Kaneko, Toshiro; Kanzaki, Makoto

2016-01-01

Non-equilibrium atmospheric-pressure plasma (APP) is used medically for plasma-induced cell permeabilization. However, how plasma irradiation specifically triggers permeabilization remains unclear. In an attempt to identify the dominant factor( s ), the distribution of plasma-produced reactive species was investigated, primarily focusing on OH radicals. A stronger plasma discharge, which produced more OH radicals in the gas phase, also produced more OH radicals in the liquid phase (OH aq ), enhancing the cell membrane permeability. In addition, plasma irradiation-induced enhancement of cell membrane permeability decreased markedly with increased solution thickness (<1 mm), and the plasma-produced OH aq decayed in solution (diffusion length on the order of several hundred micrometers). Furthermore, the horizontally center-localized distribution of OH aq corresponded with the distribution of the permeabilized cells by plasma irradiation, while the overall plasma-produced oxidizing species in solution (detected by iodine-starch reaction) exhibited a doughnut-shaped horizontal distribution. These results suggest that OH aq, among the plasma-produced oxidizing species, represents the dominant factor in plasma-induced cell permeabilization. These results enhance the current understanding of the mechanism of APP as a cell-permeabilization tool. (paper)

Coherent cancellation of geometric phase for the OH molecule in external fields

Science.gov (United States)

Bhattacharya, M.; Marin, S.; Kleinert, M.

2014-05-01

The OH molecule in its ground state presents a versatile platform for precision measurement and quantum information processing. These applications vitally depend on the accurate measurement of transition energies between the OH levels. Significant sources of systematic errors in these measurements are shifts based on the geometric phase arising from the magnetic and electric fields used for manipulating OH. In this article, we present these geometric phases for fields that vary harmonically in time, as in the Ramsey technique. Our calculation of the phases is exact within the description provided by our recent analytic solution of an effective Stark-Zeeman Hamiltonian for the OH ground state. This Hamiltonian has been shown to model experimental data accurately. We find that the OH geometric phases exhibit rich structure as a function of the field rotation rate. Remarkably, we find rotation rates where the geometric phase accumulated by a specific state is zero, or where the relative geometric phase between two states vanishes. We expect these findings to be of importance to precision experiments on OH involving time-varying fields. More specifically, our analysis quantitatively characterizes an important item in the error budget for precision spectroscopy of ground-state OH.

Ab-Initio Modelling Of Surface Site Reactivity And Fluid Transport In Clay Minerals Case Study: Pyrophyllite

International Nuclear Information System (INIS)

Churakov, S.V.

2005-01-01

Pyrophyllite, Al 2 [Si 4 O 10 ](OH) 2 , is the simplest structural prototype for 2:1 dioctahedral phyllosilicate. Because the net electric charge in pyrophyllite is zero, it is the best candidate for investigating the non electrostatic contribution to sorption and transport phenomena in clays. Using ab-initio simulations, we have investigated the reactivity and structure of the water-solid interface on the basal plane and edge sites of pyrophyllite. The calculations predict slightly hydrophobic behaviour of the basal plane. For the high water coverage (100), (110) and (-110), lateral facets have a lower energy than for the (010), (130) and (-130) surfaces. Analysis of the surface reactivity reveals that the =Al-OH groups are most easily protonated on the (010), (130) and (-130) facets. The =Al-O-Si= sites will be protonated on the (100), (130), (110), (-110) and (-130) surfaces. The =Al-OH 2 complexes are more easily de-protonated than the =Si-OH and =Al-OH sites. A spontaneous, reversible exchange of the protons between the solution and the edge sites has been observed in ab-initio molecular dynamics simulations at 300 K. Such near-surface proton diffusion may result in a significant contribution to the diffusion coefficients measured in neutron scattering experiments. (author)

76 FR 32071 - Safety Zone; Conneaut Festival Fireworks, Conneaut Harbor, Conneaut, OH

Science.gov (United States)

2011-06-03

...-AA00 Safety Zone; Conneaut Festival Fireworks, Conneaut Harbor, Conneaut, OH AGENCY: Coast Guard, DHS... Conneaut Harbor, Conneaut, OH for the Conneaut Festival Fireworks. This zone is intended to restrict vessels from a portion of Conneaut Harbor, Conneaut, OH during the Conneaut Festival Fireworks on July 3...

Clumped isotope effects during OH and Cl oxidation of methane

DEFF Research Database (Denmark)

Whitehill, Andrew R.; Joelsson, Lars Magnus T.; Schmidt, Johan Albrecht

2017-01-01

A series of experiments were carried out to determine the clumped (13CH3D) methane kinetic isotope effects during oxidation of methane by OH and Cl radicals, the major sink reactions for atmospheric methane. Experiments were performed in a 100 L quartz photochemical reactor, in which OH was produ......A series of experiments were carried out to determine the clumped (13CH3D) methane kinetic isotope effects during oxidation of methane by OH and Cl radicals, the major sink reactions for atmospheric methane. Experiments were performed in a 100 L quartz photochemical reactor, in which OH...... effects for singly substituted species were consistent with previous experimental studies. For doubly substituted methane, 13CH3D, the observed kinetic isotope effects closely follow the product of the kinetic isotope effects for the 13C and deuterium substituted species (i.e., 13,2KIE = 13KIE × 2KIE...... reactions. In a closed system, however, this effect is overtaken by the large D/H isotope effect, which causes the residual methane to become anti-clumped relative to the initial methane. Based on these results, we demonstrate that oxidation of methane by OH, the predominant oxidant for tropospheric methane...

Behaviour of OH radicals in an atmospheric-pressure streamer discharge studied by two-dimensional numerical simulation

International Nuclear Information System (INIS)

Komuro, Atsushi; Ono, Ryo; Oda, Tetsuji

2013-01-01

The production process of OH radicals in an atmospheric-pressure streamer discharge is studied. A streamer discharge model is developed to analyse the characteristics of a pulsed positive streamer discharge in point-to-plane electrodes filled with humid air at atmospheric pressure. The results indicate that the behaviour of OH radicals in and after the discharge pulse is characterized by three reaction processes: ‘OH-production’, ‘OH-cycle’ and ‘OH-recombination’. The first process of OH-production includes dissociation reactions of H 2 O with O( 1 D) and N 2 (a' 1 Σ u - ), which are the main production processes of OH in the discharge. Immediately after the OH-production process, the OH radicals are destroyed by a reaction with O( 3 P) to form O 2 and H. Then the subsequent reactions produce OH again through the reaction of H + HO 2 , which is the OH-cycle process. Finally, the OH radicals are consumed by the OH-recombination process. (paper)

Nanoporous Al sandwich foils using size effect of Al layer thickness during Cu/Al/Cu laminate rolling

Science.gov (United States)

Yu, Hailiang; Lu, Cheng; Tieu, A. Kiet; Li, Huijun; Godbole, Ajit; Kong, Charlie

2018-06-01

The roll bonding technique is one of the most widely used methods to produce metal laminate sheets. Such sheets offer interesting research opportunities for both scientists and engineers. In this paper, we report on an experimental investigation of the 'thickness effect' during laminate rolling for the first time. Using a four-high multifunction rolling mill, Cu/Al/Cu laminate sheets were fabricated with a range of thicknesses (16, 40, 70 and 130 μm) of the Al layer. The thickness of the Cu sheets was a constant 300 μm. After rolling, TEM images show good bonding quality between the Cu and Al layers. However, there are many nanoscale pores in the Al layer. The fraction of nanoscale pores in the Al layer increases with a reduction in the Al layer thickness. The finite element method was used to simulate the Cu/Al/Cu rolling process. The simulation results reveal the effect of the Al layer thickness on the deformation characteristics of the Cu/Al/Cu laminate. Finally, we propose that the size effect of the Al layer thickness during Cu/Al/Cu laminate rolling may offer a method to fabricate 'nanoporous' Al sandwich laminate foils. Such foils can be used in electromagnetic shielding of electrical devices and noisy shielding of building.

Detection of OH from Comet Halley in the far-infrared

International Nuclear Information System (INIS)

Stacey, G.J.; Lugten, J.B.; Genzel, R.

1986-01-01

The 2 Pi 3/2 (J = 5/2 yields 3/2 + yields - parity) transition of OH was detected in comet Halley at 119.44 microns. The upper limit to the line intensity of the - yields + parity transition is 119.23 microns. The ratio of these lines is consistent with radiative pumping of the rotational levels through absorption of near ultraviolet solar photons which excite the low lying vibrational levels of OH. The far-infrared lines probe the inner regions of the coma where OH is produced through photodissociation of a parent molecule (presumably H 2 O). Hence, these lines complement the 18 cm radio measurements which are sensitive to the outer regions of the comet coma. The OH production rate is highly model dependent but is of the order 2 to 4 times 10 to the 29th power molecules/sec

Comparison of Efficiencies and Mechanisms of Catalytic Ozonation of Recalcitrant Petroleum Refinery Wastewater by Ce, Mg, and Ce-Mg Oxides Loaded Al2O3

Directory of Open Access Journals (Sweden)

Chunmao Chen

2017-02-01

Full Text Available The use of catalytic ozonation processes (COPs for the advanced treatment of recalcitrant petroleum refinery wastewater (RPRW is rapidly expanding. In this study, magnesium (Mg, cerium (Ce, and Mg-Ce oxide-loaded alumina (Al2O3 were developed as cost efficient catalysts for ozonation treatment of RPRW, having performance metrics that meet new discharge standards. Interactions between the metal oxides and the Al2O3 support influence the catalytic properties, as well as the efficiency and mechanism. Mg-Ce/Al2O3 (Mg-Ce/Al2O3-COP reduced the chemical oxygen demand by 4.7%, 4.1%, 6.0%, and 17.5% relative to Mg/Al2O3-COP, Ce/Al2O3-COP, Al2O3-COP, and single ozonation, respectively. The loaded composite metal oxides significantly increased the hydroxyl radical-mediated oxidation. Surface hydroxyl groups (–OHs are the dominant catalytic active sites on Al2O3. These active surface –OHs along with the deposited metal oxides (Mg2+ and/or Ce4+ increased the catalytic activity. The Mg-Ce/Al2O3 catalyst can be economically produced, has high efficiency, and is stable under acidic and alkaline conditions.

Processing of spent NiW/Al{sub 2}O{sub 3} catalysts

Energy Technology Data Exchange (ETDEWEB)

Paulino, Jessica Frontino; Afonso, Julio Carlos, E-mail: julio@iq.ufrj.br [Departamento de Quimica Analitica, Instituto de Quimica, Universidade Federal do Rio de Janeiro, RJ (Brazil); Cunha, Jose Waldemar Silva Dias da [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), RJ (Brazil). Departamento de Quimica e Materiais Nucleares

2013-09-01

Spent oxidized (500 deg C, 5 h) commercial NiW/Al{sub 2}O{sub 3} catalysts were processed using two different routes: a) fusion with NaOH (650 deg C, 1 h), the roasted mass was leached in water; b) leaching with HCl or H{sub 2}SO{sub 4} (70 deg C, 1-3 h). HCl was the best leachant. In both routes, soluble tungsten was extracted at pH 1 with Alamine 336 (10 vol.% in kerosene) and stripped with 2 mol L{sup -1} NH{sub 4}OH (25 deg C, one stage, aqueous/organic ratio = 1 v/v). Tungsten was isolated as ammonium paratungstate at very high yield (> 97.5%). The elements were better separated using the acidic route. (author)

Effect of AlF3 Production Waste on the Properties of Hardened Cement Paste

Directory of Open Access Journals (Sweden)

Danutė VAIČIUKYNIENĖ

2012-06-01

Full Text Available The possibility to use by-product SiO2·nH2O (often called AlF3 production waste in cement casting has been attracting the interest of researchers for many years, although high content of fluorine makes the use of amorphous SiO2 problematic. Finding the way of utilizing waste products is a very important research topic at the moment. In this study AlF3 production waste was investigated as the basic ingredient of a new pozzolanic material. The goal of this study is to investigate the possibilities of using AlF3 production waste, washed in ammonia solution, in cement stone specimens. Chemically treated silica gel additive was proved to reduce the amount of Ca(OH2 and CaCO3 in hardened cement paste samples. Experimental research has revealed that the density in hydrated samples reduces from 2220 kg/m3 to 2030 kg/m3 with the increase of silica gel content from 0 % to 35 %. The compressive strength of samples containing 10 % of silica gel additive increased by 8.04 % compared to the samples without the additive. SiO2 additive used at 10 % and 20 % increased the maximum hydration temperature. In this case, the additive modifies the hydration kinetics.DOI: http://dx.doi.org/10.5755/j01.ms.18.2.1925

Quantifying the causes of differences in tropospheric OH within global models

Science.gov (United States)

Nicely, Julie M.; Salawitch, Ross J.; Canty, Timothy; Anderson, Daniel C.; Arnold, Steve R.; Chipperfield, Martyn P.; Emmons, Louisa K.; Flemming, Johannes; Huijnen, Vincent; Kinnison, Douglas E.; Lamarque, Jean-François; Mao, Jingqiu; Monks, Sarah A.; Steenrod, Stephen D.; Tilmes, Simone; Turquety, Solene

2017-02-01

The hydroxyl radical (OH) is the primary daytime oxidant in the troposphere and provides the main loss mechanism for many pollutants and greenhouse gases, including methane (CH4). Global mean tropospheric OH differs by as much as 80% among various global models, for reasons that are not well understood. We use neural networks (NNs), trained using archived output from eight chemical transport models (CTMs) that participated in the Polar Study using Aircraft, Remote Sensing, Surface Measurements and Models, of Climate, Chemistry, Aerosols and Transport Model Intercomparison Project (POLMIP), to quantify the factors responsible for differences in tropospheric OH and resulting CH4 lifetime (τCH4) between these models. Annual average τCH4, for loss by OH only, ranges from 8.0 to 11.6 years for the eight POLMIP CTMs. The factors driving these differences were quantified by inputting 3-D chemical fields from one CTM into the trained NN of another CTM. Across all CTMs, the largest mean differences in τCH4 (ΔτCH4) result from variations in chemical mechanisms (ΔτCH4 = 0.46 years), the photolysis frequency (J) of O3 → O(1D) (0.31 years), local O3 (0.30 years), and CO (0.23 years). The ΔτCH4 due to CTM differences in NOx (NO + NO2) is relatively low (0.17 years), although large regional variation in OH between the CTMs is attributed to NOx. Differences in isoprene and J(NO2) have negligible overall effect on globally averaged tropospheric OH, although the extent of OH variations due to each factor depends on the model being examined. This study demonstrates that NNs can serve as a useful tool for quantifying why tropospheric OH varies between global models, provided that essential chemical fields are archived.

Observation of OH radicals produced by pulsed discharges on the surface of a liquid

Science.gov (United States)

Kanazawa, Seiji; Kawano, Hirokazu; Watanabe, Satoshi; Furuki, Takashi; Akamine, Shuichi; Ichiki, Ryuta; Ohkubo, Toshikazu; Kocik, Marek; Mizeraczyk, Jerzy

2011-06-01

The hydroxyl radical (OH) plays an important role in plasma chemistry at atmospheric pressure. OH radicals have a higher oxidation potential compared with other oxidative species such as free radical O, atomic oxygen, hydroperoxyl radical (HO2), hydrogen peroxide(H2O2) and ozone. In this study, surface discharges on liquids (water and its solutions) were investigated experimentally. A pulsed streamer discharge was generated on the liquid surface using a point-to-plane electrode geometry. The primary generation process of OH radicals is closely related to the streamer propagation, and the subsequent secondary process after the discharge has an influence on the chemical reaction. Taking into account the timescale of these processes, we investigated the behavior of OH radicals using two different diagnostic methods. Time evolution of the ground-state OH radicals above the liquid surface after the discharge was observed by a laser-induced fluorescence (LIF) technique. In order to observe the ground-state OH, an OH [A 2∑+(v' = 1) <-- X 2Π(v'' = 0)] system at 282 nm was used. As the secondary process, a portion of OH radicals diffused from gas phase to the liquid surface and dissolved in the liquid. These dissolved OH radicals were measured by a chemical probe method. Terephthalic acid was used as an OH radical trap and fluorescence of the resulting 2-hydroxyterephthalic acid was measured. This paper directly presents visualization of OH radicals over the liquid surface by means of LIF, and indirectly describes OH radicals dissolved in water by means of a chemical method.

Reductive amination of ethanol to ethylamines over Ni/Al{sub 2}O{sub 3} catalysts

Energy Technology Data Exchange (ETDEWEB)

Park, Jun Hyun [Korea Research Institute of Chemical Technology, Daejeon (Korea, Republic of); Hong, Eunpyo; An, Sang Hee; Shin, Chae-Ho; Lim, Dong-Hee [Chungbuk National University, Chungju (Korea, Republic of)

2017-10-15

Ni(x)/Al{sub 2}O{sub 3} (x=wt%) catalysts with Ni loadings of 5-25 wt% were prepared via a wet impregnation method on an γ-Al{sub 2}O{sub 3} support and subsequently applied in the reductive amination of ethanol to ethylamines. Among the various catalysts prepared, Ni(10)/Al2O3 exhibited the highest metal dispersion and the smallest Ni particle size, resulting in the highest catalytic performance. To reveal the effects of reaction parameters, a reductive amination process was performed by varying the reaction temperature (T), weight hourly space velocity (WHSV), and NH{sub 3} and H{sub 2} partial pressures in the reactions. In addition, on/off experiments for NH{sub 3} and H{sub 2} were also carried out. In the absence of NH{sub 3} in the reactant stream, the ethanol conversion and selectivities towards the different ethylamine products were significantly reduced, while the selectivity to ethylene was dominant due to the dehydration of ethanol. In contrast, in the absence of H{sub 2}, the selectivity to acetonitrile significantly increased due to dehydrogenation of the imine intermediate. Although a small amount of catalyst deactivation was observed in the conversion of ethanol up to 10 h on stream due to the formation of nickel nitride, the Ni(10)/Al{sub 2}O{sub 3} catalyst exhibited stable catalytic performance over 90 h under the optimized reaction conditions (i.e., T=190 .deg. C, WHSV=0.9 h{sup -1}, and EtOH/NH{sub 3}/H{sub 2} molar ratio=1/1/6).

SMA OBSERVATIONS OF THE W3(OH) COMPLEX: PHYSICAL AND CHEMICAL DIFFERENTIATION BETWEEN W3(H{sub 2}O) AND W3(OH)

Energy Technology Data Exchange (ETDEWEB)

Qin, Sheng-Li [Department of Astronomy, Yunnan University, and Key Laboratory of Astroparticle Physics of Yunnan Province, Kunming, 650091 (China); Schilke, Peter; Sánchez-Monge, Álvaro [Physikalisches Institut, Universität zu Köln, Zülpicher Str. 77, D-50937 Köln (Germany); Wu, Jingwen [Department of Physics and Astronomy, University of California, Los Angeles, CA 90095 (United States); Wu, Yuefang [Department of Astronomy, Peking University, Beijing, 100871 (China); Liu, Tie [Korea Astronomy and Space Science Institute 776, Daedeokdaero, Yuseong-gu, Daejeon, Korea 305-348 (Korea, Republic of); Liu, Ying, E-mail: slqin@bao.ac.cn [Department of Physics and Hebei Advanced Thin Film Laboratory, Hebei Normal University, Shijiazhuang 050024 (China)

2015-04-10

We report on the Submillimeter Array (SMA) observations of molecular lines at 270 GHz toward the W3(OH) and W3(H{sub 2}O) complex. Although previous observations already resolved the W3(H{sub 2}O) into two or three sub-components, the physical and chemical properties of the two sources are not well constrained. Our SMA observations clearly resolved the W3(OH) and W3(H{sub 2}O) continuum cores. Taking advantage of the line fitting tool XCLASS, we identified and modeled a rich molecular spectrum in this complex, including multiple CH{sub 3}CN and CH{sub 3}OH transitions in both cores. HDO, C{sub 2}H{sub 5}CN, O{sup 13}CS, and vibrationally excited lines of HCN, CH{sub 3}CN, and CH{sub 3}OCHO were only detected in W3(H{sub 2}O). We calculate gas temperatures and column densities for both cores. The results show that W3(H{sub 2}O) has higher gas temperatures and larger column densities than W3(OH) as previously observed, suggesting physical and chemical differences between the two cores. We compare the molecular abundances in W3(H{sub 2}O) to those in the Sgr B2(N) hot core, the Orion KL hot core, and the Orion Compact Ridge, and discuss the chemical origin of specific species. An east–west velocity gradient is seen in W3(H{sub 2}O), and the extension is consistent with the bipolar outflow orientation traced by water masers and radio jets. A north–south velocity gradient across W3(OH) is also observed. However, with current observations we cannot be assured whether the velocity gradients are caused by rotation, outflow, or radial velocity differences of the sub-components of W3(OH)

Rate constants and mechanisms for the crystallization of Al nano-goethite under environmentally relevant conditions

Science.gov (United States)

Bazilevskaya, Ekaterina; Archibald, Douglas D.; Martínez, Carmen Enid

2012-07-01

Mobile inorganic and organic nanocolloidal particles originate-from and interact-with bulk solid phases in soil and sediment environments, and as such, they contribute to the dynamic properties of environmental systems. In particular, ferrihydrite and (nano)goethite are the most abundant of nanocolloidal Fe oxy(hydr)oxides in these environments. We therefore investigated the ferrihydrite to goethite phase transformation using experimental reaction conditions that mimicked environmental conditions where the formation of nanocolloidal Fe oxy(hydr)oxides may occur: slow titration of dilute solutions to pH 5 at 25 °C with and without 2 mol% Al. Subsequently, the rate constants from 54-d nano-goethite aging/crystallization experiments at 50 °C were determined using aliquots pulled for vibrational spectroscopy (including multivariate curve resolution, MCR, analyses of infrared spectra) and synchrotron-based X-ray diffraction (XRD). We also present a mechanistic model that accounts for the nano-goethite crystallization observed by the aforementioned techniques, and particle structural characteristics observed by dynamic light scattering (DLS) and transmission electron microscopy (TEM). In contrast to the common assumption that metastable ferrihydrite precipitates first, before it transforms to goethite, the presence of characteristic infrared bands in freshly synthesized nanoparticle suspensions indicate goethite can precipitate directly from solution under environmentally relevant conditions: low Fe concentration, ambient temperature, and pH maintained at 5. However, the presence of 2 mol% Al prevented direct goethite precipitation. Rate constants obtained by fitting the contributions from the MCR-derived goethite-like component to the OH-stretching region were (7.4 ± 1.1) × 10-7 s-1 for 0% Al and (4.2 ± 0.4) × 10-7 s-1 for 2 mol% Al suspensions. Rate constants derived from intensities of OH-bending infrared vibrations (795 and 895 cm-1) showed similar values

Electronic quenching of OH(A) by water in atmospheric pressure plasmas and its influence on the gas temperature determination by OH(A-X) emission

International Nuclear Information System (INIS)

Bruggeman, Peter; Schram, Daan C; Iza, Felipe; Kong, Michael G; Guns, Peter; Lauwers, Daniel; Leys, Christophe; Gonzalvo, Yolanda Aranda

2010-01-01

In this paper it is shown that electronic quenching of OH(A) by water prevents thermalization of the rotational population distribution of OH(A). This means that the observed ro-vibrational OH(A-X) emission band is (at least partially) an image of the formation process and is determined not only by the gas temperature. The formation of negative ions and clusters for larger water concentrations can contribute to the non-equilibrium. The above is demonstrated in RF excited atmospheric pressure glow discharges in He-water mixtures in a parallel metal plate reactor by optical emission spectroscopy. For this particular case a significant overpopulation of high rotational states appears around 1000 ppm H 2 O in He. The smallest temperature parameter of a non-Boltzmann (two-temperature) distribution fitted to the experimental spectrum of OH(A-X) gives a good representation of the gas temperature. Only the rotational states with the smallest rotational numbers (J ≤ 7) are thermalized and representative for the gas temperature.

Electronic quenching of OH(A) by water in atmospheric pressure plasmas and its influence on the gas temperature determination by OH(A-X) emission

Energy Technology Data Exchange (ETDEWEB)

Bruggeman, Peter; Schram, Daan C [Department of Applied Physics, Technische Universiteit Eindhoven, PO Box 513, 5600 MB Eindhoven (Netherlands); Iza, Felipe; Kong, Michael G [Department of Electronic and Electrical Engineering, Loughborough University, Loughborough, Leicestershire LE11 3TU (United Kingdom); Guns, Peter; Lauwers, Daniel; Leys, Christophe [Department of Applied Physics, Ghent University, Jozef Plateaustraat 22, B-9000 Ghent (Belgium); Gonzalvo, Yolanda Aranda [Plasma and Surface Analysis Division, Hiden Analytical Ltd, 420 Europa Boulevard, Warrington WA5 7UN (United Kingdom)], E-mail: p.j.bruggeman@tue.nl

2010-02-15

In this paper it is shown that electronic quenching of OH(A) by water prevents thermalization of the rotational population distribution of OH(A). This means that the observed ro-vibrational OH(A-X) emission band is (at least partially) an image of the formation process and is determined not only by the gas temperature. The formation of negative ions and clusters for larger water concentrations can contribute to the non-equilibrium. The above is demonstrated in RF excited atmospheric pressure glow discharges in He-water mixtures in a parallel metal plate reactor by optical emission spectroscopy. For this particular case a significant overpopulation of high rotational states appears around 1000 ppm H{sub 2}O in He. The smallest temperature parameter of a non-Boltzmann (two-temperature) distribution fitted to the experimental spectrum of OH(A-X) gives a good representation of the gas temperature. Only the rotational states with the smallest rotational numbers (J {<=} 7) are thermalized and representative for the gas temperature.

Structural Differentiation between Layered Single (Ni) and Double Metal Hydroxides (Ni–Al LDHs) Using Wavelet Transformation

Energy Technology Data Exchange (ETDEWEB)

Siebecker, Matthew G. [University of Delaware, Delaware Environmental Institute; Sparks, Donald L. [University of Delaware, Delaware Environmental Institute

2017-09-07

Layered double hydroxides (LDHs) are anionic clays important in disciplines such as environmental chemistry, geochemistry, and materials science. Developments in signal processing of extended X-ray absorption fine structure (EXAFS) data, such as wavelet transformation (WT), have been used to identify transition metals and Al present in the hydroxide sheets of LDHs. The WT plots of LDHs should be distinct from those of isostructural single metal hydroxides. However, no direct comparison of these minerals appears in the literature using WT. This work systematically analyzes a suite of Ni-rich mineral standards, including Ni–Al LDHs, single metal Ni hydroxides, and Ni-rich silicates using WT. The results illustrate that the WT plots for α-Ni(OH)2 and Ni–Al LDHs are often indistinguishable from each other, with similar two-component plots for the different mineral types. This demonstrates that the WT of the first metal shell often cannot be used to differentiate an LDH from a single metal hydroxide. Interlayer anions adsorbed to the hydroxide sheet of α-Ni(OH)2 affect the EXAFS spectra and are not visible in the FT but are clearly resolved and discrete in the WT.

Novedoso método para preparar materiales nanoporosos compuestos MFI/MCM-41 a partir de caolín venezolano. Efecto de la concentración de NaOH

Directory of Open Access Journals (Sweden)

Freddy Imbert

2012-05-01

Full Text Available A MFI/MCM-41 composite material, a zeolite type MFI and Al-MCM-41 were synthesized from kaolin, using TPA and CTAB as structure directing agents. The MFI/MCM-41 composite material was synthesized in two steps. In the first, MFI was obtained and then treated with solutions of different NaOH concentrations (1 – 4M, in the second step the reaction mixture was treated under MCM-41 synthesis conditions. The solids obtained were characterized by scanning electron microscopy (SEM, chemical analysis by energy dispersive X-ray spectroscopy (EDX, transmission electron microscopy (TEM, adsorption of N2 at 77K, X-ray diffraction (XRD. In the absence of alkaline treatment two phases were observed – zeolite and mesoporous, whereas the zeolite crystals were larger than mesoporous particles. The alkaline treatment dissolved the zeolite structure creating mesoporosity, modifying the characteristic zeolite morphology and reducing its crystal domains. The treatment with 2 or 3M NaOH eases zeolite dissolution and leads to assemble of the zeolite building units around the surfactant and into the mesoporous walls. The incorporation of the zeolite building units into the mesoporous walls is governed by the relative quantities of crystalline and amorphous materials in the synthesis gel. The treatment with 4M NaOH led exclusively to the formation of Al-MCM-41.

OH radicals distribution in an Ar-H2O atmospheric plasma jet

Science.gov (United States)

Li, L.; Nikiforov, A.; Xiong, Q.; Britun, N.; Snyders, R.; Lu, X.; Leys, C.

2013-09-01

Recently, plasma jet systems found numerous applications in the field of biomedicine and treatment of temperature-sensitive materials. OH radicals are one of the main active species produced by these plasmas. Present study deals with the investigation of RF atmospheric pressure plasma jet in terms of OH radicals production by admixture of H2O into argon used as a feed gas. Generation of OH radicals is studied by laser-induced fluorescence spectroscopy. The excitation dynamics of OH radicals induced by the laser photons is studied by time-resolved spectroscopy. It is shown that vibrational and rotational energy transfer processes, which are sensitive to the surrounding species, can lead to the complication in the OH radicals diagnostics at high pressure and have to be considered during experiments. The axial and radial 2D maps of absolute densities of hydroxyl radicals at different water contents are obtained. The highest density of 1.15 × 1020 m-3 is measured in the plasma core for the case of 0.3% H2O. In the x-y-plane, the OH density steeply decreases within a range of ±2 mm from its maximum value down to 1018 m-3. The effect of H2O addition on the generation of OH radicals is investigated and discussed.

Vitamina D y cáncer: acción antineoplásica de la 1α, 25(OH2 -vitamina D3

Directory of Open Access Journals (Sweden)

Verónica González Pardo

2012-04-01

Full Text Available La forma hormonalmente activa de la vitamina D, 1α,25(OH2-vitamina D3 (1α,25(OH2D3, además de desempeñar un rol crucial en el mantenimiento de la homeostasis de calcio en el cuerpo, también regula el crecimiento y la diferenciación de diferentes tipos celulares, incluyendo células cancerosas. Actualmente hay numerosos estudios que investigan los efectos de la hormona en estas células, debido al interés en el uso terapéutico del 1α,25(OH2D3 y de análogos con menor actividad calcémica para el tratamiento o prevención del cáncer. En este trabajo de revisión se describe el sistema endocrino de la vitamina D, su mecanismo de acción, su acción antineoplásica y se provee información sobre los últimos avances en el estudio de nuevos análogos de la hormona con menos actividad calcémica para el tratamiento del cáncer.

Influence of annealing temperature on passivation performance of thermal atomic layer deposition Al2O3 films

International Nuclear Information System (INIS)

Zhang Xiang; Liu Bang-Wu; Li Chao-Bo; Xia Yang; Zhao Yan

2013-01-01

Chemical and field-effect passivation of atomic layer deposition (ALD) Al 2 O 3 films are investigated, mainly by corona charging measurement. The interface structure and material properties are characterized by transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS), respectively. Passivation performance is improved remarkably by annealing at temperatures of 450 °C and 500 °C, while the improvement is quite weak at 600 °C, which can be attributed to the poor quality of chemical passivation. An increase of fixed negative charge density in the films during annealing can be explained by the Al 2 O 3 /Si interface structural change. The Al—OH groups play an important role in chemical passivation, and the Al—OH concentration in an as-deposited film subsequently determines the passivation quality of that film when it is annealed, to a certain degree. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Mid-infrared signatures of hydroxyl containing water clusters: Infrared laser Stark spectroscopy of OH–H{sub 2}O and OH(D{sub 2}O){sub n} (n = 1-3)

Energy Technology Data Exchange (ETDEWEB)

Hernandez, Federico J. [Department of Chemistry, University of Georgia, Athens, Georgia 30602 (United States); INFIQC, Dpto. de Fisicoquímica, Facultad de Ciencias Químicas, Centro Láser de Ciencias Moleculares, Universidad Nacional de Córdoba, Ciudad Universitaria, Pabellón, X5000HUA Córdoba (Argentina); Brice, Joseph T.; Leavitt, Christopher M.; Liang, Tao; Douberly, Gary E., E-mail: douberly@uga.edu [Department of Chemistry, University of Georgia, Athens, Georgia 30602 (United States); Raston, Paul L. [Department of Chemistry and Biochemistry, James Madison University, Harrisonburg, Virginia 22807 (United States); Pino, Gustavo A. [INFIQC, Dpto. de Fisicoquímica, Facultad de Ciencias Químicas, Centro Láser de Ciencias Moleculares, Universidad Nacional de Córdoba, Ciudad Universitaria, Pabellón, X5000HUA Córdoba (Argentina)

2015-10-28

Small water clusters containing a single hydroxyl radical are synthesized in liquid helium droplets. The OH–H{sub 2}O and OH(D{sub 2}O){sub n} clusters (n = 1-3) are probed with infrared laser spectroscopy in the vicinity of the hydroxyl radical OH stretch vibration. Experimental band origins are qualitatively consistent with ab initio calculations of the global minimum structures; however, frequency shifts from isolated OH are significantly over-predicted by both B3LYP and MP2 methods. An effective Hamiltonian that accounts for partial quenching of electronic angular momentum is used to analyze Stark spectra of the OH–H{sub 2}O and OH–D{sub 2}O binary complexes, revealing a 3.70(5) D permanent electric dipole moment. Computations of the dipole moment are in good agreement with experiment when large-amplitude vibrational averaging is taken into account. Polarization spectroscopy is employed to characterize two vibrational bands assigned to OH(D{sub 2}O){sub 2}, revealing two nearly isoenergetic cyclic isomers that differ in the orientation of the non-hydrogen-bonded deuterium atoms relative to the plane of the three oxygen atoms. The dipole moments for these clusters are determined to be approximately 2.5 and 1.8 D for “up-up” and “up-down” structures, respectively. Hydroxyl stretching bands of larger clusters containing three or more D{sub 2}O molecules are observed shifted approximately 300 cm{sup −1} to the red of the isolated OH radical. Pressure dependence studies and ab initio calculations imply the presence of multiple cyclic isomers of OH(D{sub 2}O){sub 3}.

IS OHS NEGLIGENCE AND EVASION AN “ERROR OF JUDGEMENT” OR “WHITE-COLLAR CRIME”? AN INTERPRETATION OF APPAREL MANUFACTURERS IN BANGLADESH

Directory of Open Access Journals (Sweden)

Muhammad Faisol Chowdhury

2016-12-01

Full Text Available This paper investigates the managerial interpretation of the terms “error of judgement” and “white-collar crime” in relation to the evasion or negligence observed in administering occupational health and safety (OHS provisions in the apparel manufacturing sector of Bangladesh. The research is qualitative in nature and follows an interpretivist paradigm. The questionnaire responses were collected from 20 mid- and top-level managers from 10 large apparel manufacturing factories located on the outskirts of Dhaka. The research reveals that all of the respondents have adequate knowledge about the relevant OHS provisions and safety protocols imposed on them by the local government and the global supply chain. They believe that the correct administration of the OHS provisions will reduce workplace accidents effectively. The research unfolds that the respondents interpret in different ways the terms "error of judgement” and “white-collar crime” in association with OHS negligence and evasion. Although empirical evidence shows that this type of negligence and evasion are considered as white-collar crime and punishable, most of the respondents in this research do not subscribe to this notion and alternatively believe that it is an “error of judgement” and therefore non-punishable.

Evaluation of a Russian version of the oral health literacy instrument (OHLI).

Science.gov (United States)

Blizniuk, Anastasiya; Ueno, Masayuki; Furukawa, Sayaka; Kawaguchi, Yoko

2014-11-27

Oral health literacy has become a popular research area in the last decade; however, to date no health literacy instruments in the Russian language exist. The objectives of this study were to develop a Russian version of the Oral Health Literacy Instrument (OHLI) and to examine its reliability and validity. A convenience sample of patients who visited the dental division of the district hospital in Belarus was used in the study. The OHLI, created originally in English, was modified to adapt it to characteristics of routine dental services in Belarus and then translated into Russian, followed by back-translation. Participants completed a self-administered socio-demographic questionnaire, an oral health knowledge test and the Russian version of the OHLI (R-OHLI). Bivariate and multivariate statistical analyses, including multiple regression modeling, were performed to examine reliability and validity of the R-OHLI. Participants were 281 adult patients aged from 18 to 60 years, with a mean age of 33.1 ± 12.2; 64.1% of them were women. Cronbach's alpha values for the two sections (reading comprehension and numeracy) and the total R-OHLI were 0.853, 0.815 and 0.895, respectively. The mean total R-OHLI score was 77.2 ± 14.5; the mean reading comprehension and numeracy scores were 39.5 ± 7.5 and 37.8 ± 8.8, respectively. The R-OHLI was significantly correlated to the oral health knowledge test. Pearson's correlation coefficients between the oral health knowledge test and the reading comprehension, numeracy and total R-OHLI were 0.401, 0.258, and 0.363, respectively (p literacy instrument for Russian-speaking people.

Observation of OH radicals produced by pulsed discharges on the surface of a liquid

Energy Technology Data Exchange (ETDEWEB)

Kanazawa, Seiji; Kawano, Hirokazu; Watanabe, Satoshi; Furuki, Takashi; Akamine, Shuichi; Ichiki, Ryuta; Ohkubo, Toshikazu [Department of Electrical and Electronic Engineering, Oita University, 700 Dannoharu, Oita 870-1192 (Japan); Kocik, Marek; Mizeraczyk, Jerzy, E-mail: skana@cc.oita-u.ac.jp [Szewalski Institute of Fluid Flow Machinery, Polish Academy of Sciences Fiszera 14, 80-952, Gdansk (Poland)

2011-06-15

The hydroxyl radical (OH) plays an important role in plasma chemistry at atmospheric pressure. OH radicals have a higher oxidation potential compared with other oxidative species such as free radical O, atomic oxygen, hydroperoxyl radical (HO{sub 2}), hydrogen peroxide(H{sub 2}O{sub 2}) and ozone. In this study, surface discharges on liquids (water and its solutions) were investigated experimentally. A pulsed streamer discharge was generated on the liquid surface using a point-to-plane electrode geometry. The primary generation process of OH radicals is closely related to the streamer propagation, and the subsequent secondary process after the discharge has an influence on the chemical reaction. Taking into account the timescale of these processes, we investigated the behavior of OH radicals using two different diagnostic methods. Time evolution of the ground-state OH radicals above the liquid surface after the discharge was observed by a laser-induced fluorescence (LIF) technique. In order to observe the ground-state OH, an OH [A {sup 2}{Sigma}{sup +}(v' = 1) <- X {sup 2}{Pi}(v'' = 0)] system at 282 nm was used. As the secondary process, a portion of OH radicals diffused from gas phase to the liquid surface and dissolved in the liquid. These dissolved OH radicals were measured by a chemical probe method. Terephthalic acid was used as an OH radical trap and fluorescence of the resulting 2-hydroxyterephthalic acid was measured. This paper directly presents visualization of OH radicals over the liquid surface by means of LIF, and indirectly describes OH radicals dissolved in water by means of a chemical method.

A STUDY OF RO-VIBRATIONAL OH EMISSION FROM HERBIG Ae/Be STARS

Energy Technology Data Exchange (ETDEWEB)

Brittain, Sean D.; Reynolds, Nickalas [Department of Physics and Astronomy, 118 Kinard Laboratory, Clemson University, Clemson, SC 29634-0978 (United States); Najita, Joan R. [National Optical Astronomy Observatory, 950 N. Cherry Ave., Tucson, AZ 85719 (United States); Carr, John S. [Naval Research Laboratory, Code 7211, Washington, DC 20375 (United States); Ádámkovics, Máté, E-mail: sbritt@clemson.edu [Department of Astronomy, University of California, Berkeley, CA 94720-3411 (United States)

2016-10-20

We present a study of ro-vibrational OH and CO emission from 21 disks around Herbig Ae/Be stars. We find that the OH and CO luminosities are proportional over a wide range of stellar ultraviolet luminosities. The OH and CO line profiles are also similar, indicating that they arise from roughly the same radial region of the disk. The CO and OH emission are both correlated with the far-ultraviolet luminosity of the stars, while the polycyclic aromatic hydrocarbon (PAH) luminosity is correlated with the longer wavelength ultraviolet luminosity of the stars. Although disk flaring affects the PAH luminosity, it is not a factor in the luminosity of the OH and CO emission. These properties are consistent with models of UV-irradiated disk atmospheres. We also find that the transition disks in our sample, which have large optically thin inner regions, have lower OH and CO luminosities than non-transition disk sources with similar ultraviolet luminosities. This result, while tentative given the small sample size, is consistent with the interpretation that transition disks lack a gaseous disk close to the star.

Combustion synthesis of AlB2-Al2O3 composite powders with AlB2 nanowire structures

Science.gov (United States)

Yang, Pan; Xiao, Guoqing; Ding, Donghai; Ren, Yun; Yang, Shoulei; Lv, Lihua; Hou, Xing

2018-05-01

Using of Al and B2O3 powders as starting materials, and Mg-Al alloy as additives, AlB2-Al2O3 composite powders with AlB2 nanowire structures were successfully fabricated via combustion synthesis method in Ar atmosphere at a pressure of 1.5 MPa. The effect of different amount of Mg-Al alloy on the phase compositions and morphology of the combustion products was investigated. The results revealed that AlB2 and Al2O3 increased, whereas Al decreased with the content of Mg-Al alloy increasing. The impurities MgAl2O4 and AlB12 would exist in the sample with adding of 18 wt% Mg-Al alloy. Interestingly, FESEM/TEM/EDS results showed that AlB2 nanowires were observed in the products when the content of Mg-Al alloy is 6 wt% and 12 wt%. The more AlB2 nanowires can be found as the content of Mg-Al alloy increased. And the yield of AlB2 nanowires with the diameter of about 200 nanometers (nm) and the length up to several tens of micrometers (μm) in the combustion product is highest when the content of Mg-Al alloy is 12 wt%. The vapor, such as Mg-Al (g), B2O2 (g), AlO (g) and Al2O (g), produced during the process of combustion synthesis, reacted with each other to yield AlB2 nanowires by vapor-solid (VS) mechanism and the corresponding model was also proposed.

Few-layered Ni(OH)2 nanosheets for high-performance supercapacitors

Science.gov (United States)

Sun, Wenping; Rui, Xianhong; Ulaganathan, Mani; Madhavi, Srinivasan; Yan, Qingyu

2015-11-01

Few-layered Ni(OH)2 nanosheets (4-5 nm in thickness) are synthesized towards high-performance supercapacitors. The ultrathin Ni(OH)2 nanosheets show high specific capacitance and good rate capability in both three-electrode and asymmetric devices. In the three-electrode device, the Ni(OH)2 nanosheets deliver a high capacitance of 2064 F g-1 at 2 A g-1, and the capacitance still has a retention of 1837 F g-1 at a high current density of 20 A g-1. Such excellent performance is by far one of the best for Ni(OH)2 electrodes. In the two-electrode asymmetric device, the specific capacitance is 248 F g-1 at 1 A g-1, and reaches 113 F g-1 at 20 A g-1. The capacitance of the asymmetric device maintains to be 166 F g-1 during the 4000th cycle at 2 A g-1, suggesting good cycling stability of the device. Besides, the asymmetric device exhibits gravimetric energy density of 22 Wh kg-1 at a power density of 0.8 kW kg-1. The present results demonstrate that the ultrathin Ni(OH)2 nanosheets are highly attractive electrode materials for achieving fast charging/discharging and high-capacity supercapacitors.

EnviroAtlas - Cleveland, OH - Block Groups

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset is the base layer for the Cleveland, OH EnviroAtlas community. The block groups are from the US Census Bureau and are included/excluded...

Mechanism of the CO2-Ca(OH)2 reaction

International Nuclear Information System (INIS)

Chew, V.S.; Cheh, C.H.; Glass, R.W.

1983-01-01

Recent studies clearly showed the importance of moisture in achieving high Ca(OH) 2 absorbent utilization for removing CO 2 from gas streams at ambient temperatures. However, the role of moisture and the mechanism of the reaction was not well understood. This paper summarizes the results of a study of the mechanism of the CO 2 -Ca(OH) 2 reaction with emphasis on the role of moisture. The reaction between Ca(OH) 2 and CO 2 in moist N 2 was found to be first order with respect to the reactants with a rate constant of about 100 min -1 . At high humidities, the rate of reaction was chemically controlled, but at low humidities, the reaction rate was limited by the diffusion through the carbonate layer formed by the reaction. Calculations showed that capillary condensation could have occurred only in about 2% of the pore volume and was unlikely to have affected the reaction rate significantly by allowing the reaction to occur in the liquid phase. It was, therefore, concluded that the main role of moisture was to improve the Ca(OH) 2 utilization by lowering the resistance to diffusion through the carbonate layer

The OHS consultant as a facilitator of learning in workplace design processes

DEFF Research Database (Denmark)

Broberg, Ole; Hermund, Ingelise

2007-01-01

Occupational health service (OHS) consultancy on workplace design proc-esses in client enterprises is expected also to entail some elements of learn-ing. When the OHS consultant has performed the task the enterprise should have learned something on how to integrate health and safety aspects...... into the workplace design process, thereby making it easier for the enterprise to manage such a change in the future. The objective of this explorative study was to survey current practice of OHS consultants and put forward recom-mendations on how to improve the learning aspects of OHS consultancy. Four cases were...... devices between different communities of practice. Certain boundary objects work better than others in promoting learning and collaborative workplace design processes. For both industry and OHS units it is of importance to properly understand learning models and to align their mutual expectations...