WorldWideScience

Sample records for sandstone opening durations

  1. Slope Stability Analysis of Waste Dump in Sandstone Open Pit Osielec

    Science.gov (United States)

    Adamczyk, Justyna; Cała, Marek; Flisiak, Jerzy; Kolano, Malwina; Kowalski, Michał

    2013-03-01

    This paper presents the slope stability analysis for the current as well as projected (final) geometry of waste dump Sandstone Open Pit "Osielec". For the stability analysis six sections were selected. Then, the final geometry of the waste dump was designed and the stability analysis was conducted. On the basis of the analysis results the opportunities to improve the stability of the object were identified. The next issue addressed in the paper was to determine the proportion of the mixture containing mining and processing wastes, for which the waste dump remains stable. Stability calculations were carried out using Janbu method, which belongs to the limit equilibrium methods.

  2. Structural-Diagenetic Controls on Fracture Opening in Tight Gas Sandstone Reservoirs, Alberta Foothills

    Science.gov (United States)

    Ukar, Estibalitz; Eichhubl, Peter; Fall, Andras; Hooker, John

    2013-04-01

    relatively undeformed backlimb strata. Fracture apertures locally increase adjacent to reverse faults without an overall increase in fracture frequency. Fluid inclusion analyses of crack-seal quartz cement indicate both aqueous and methane-rich inclusions are present. Homogenization temperatures of two-phase inclusions indicate synkinematic fracture cement precipitation and fracture opening under conditions at or near maximum burial of 190-210°C in core samples, and 120-160°C in outcrop samples. In comparison with the fracture evolution in other, less deformed tight-gas sandstone reservoirs such as the Piceance and East Texas basins where fracture opening is primarily controlled by gas generation, gas charge, and pore fluid pressure, these results suggest a strong control of regional tectonic processes on fracture generation. In conjunction with timing and rate of gas charge, rates of fracture cement growth, and stratigraphic-lithological controls, these processes determine the overall distribution of open fractures in these reservoirs.

  3. Sequence stratigraphic and sedimentologic significance of biogenic structures from a late Paleozoic marginal- to open-marine reservoir, Morrow Sandstone, subsurface of southwest Kansas, USA

    Science.gov (United States)

    Buatois, L.A.; Mangano, M.G.; Alissa, A.; Carr, T.R.

    2002-01-01

    Integrated ichnologic, sedimentologic, and stratigraphic studies of cores and well logs from Lower Pennsylvanian oil and gas reservoirs (lower Morrow Sandstone, southwest Kansas) allow distinction between fluvio-estuarine and open marine deposits in the Gentzler and Arroyo fields. The fluvio-estuarine facies assemblage is composed of both interfluve and valley-fill deposits, encompassing a variety of depositional environments such as fluvial channel, interfluve paleosol, bay head delta, estuary bay, restricted tidal flat, intertidal channel, and estuary mouth. Deposition in a brackish-water estuarine valley is supported by the presence of a low diversity, opportunistic, impoverished marine ichnofaunal assemblage dominated by infaunal structures, representing an example of a mixed, depauperate Cruziana and Skolithos ichnofacies. Overall distribution of ichnofossils along the estuarine valley was mainly controlled by the salinity gradient, with other parameters, such as oxygenation, substrate and energy, acting at a more local scale. The lower Morrow estuarine system displays the classical tripartite division of wave-dominated estuaries (i.e. seaward-marine sand plug, fine-grained central bay, and sandy landward zone), but tidal action is also recorded. The estuarine valley displays a northwest-southeast trend, draining to the open sea in the southeast. Recognition of valley-fill sandstones in the lower Morrow has implications for reservoir characterization. While the open marine model predicts a "layer-cake" style of facies distribution as a consequence of strandline shoreline progradation, identification of valley-fill sequences points to more compartmentalized reservoirs, due to the heterogeneity created by valley incision and subsequent infill. The open-marine facies assemblage comprises upper, middle, and lower shoreface; offshore transition; offshore; and shelf deposits. In contrast to the estuarine assemblage, open marine ichnofaunas are characterized by a

  4. Quantifying opening-mode fracture spatial organization in horizontal wellbore image logs, core and outcrop: Application to Upper Cretaceous Frontier Formation tight gas sandstones, USA

    Science.gov (United States)

    Li, J. Z.; Laubach, S. E.; Gale, J. F. W.; Marrett, R. A.

    2018-03-01

    The Upper Cretaceous Frontier Formation is a naturally fractured gas-producing sandstone in Wyoming. Regionally, random and statistically more clustered than random patterns exist in the same upper to lower shoreface depositional facies. East-west- and north-south-striking regional fractures sampled using image logs and cores from three horizontal wells exhibit clustered patterns, whereas data collected from east-west-striking fractures in outcrop have patterns that are indistinguishable from random. Image log data analyzed with the correlation count method shows clusters ∼35 m wide and spaced ∼50 to 90 m apart as well as clusters up to 12 m wide with periodic inter-cluster spacings. A hierarchy of cluster sizes exists; organization within clusters is likely fractal. These rocks have markedly different structural and burial histories, so regional differences in degree of clustering are unsurprising. Clustered patterns correspond to fractures having core quartz deposition contemporaneous with fracture opening, circumstances that some models suggest might affect spacing patterns by interfering with fracture growth. Our results show that quantifying and identifying patterns as statistically more or less clustered than random delineates differences in fracture patterns that are not otherwise apparent but that may influence gas and water production, and therefore may be economically important.

  5. A Novel, Open Access Method to Assess Sleep Duration Using a Wrist-Worn Accelerometer.

    Directory of Open Access Journals (Sweden)

    Vincent T van Hees

    Full Text Available Wrist-worn accelerometers are increasingly being used for the assessment of physical activity in population studies, but little is known about their value for sleep assessment. We developed a novel method of assessing sleep duration using data from 4,094 Whitehall II Study (United Kingdom, 2012-2013 participants aged 60-83 who wore the accelerometer for 9 consecutive days, filled in a sleep log and reported sleep duration via questionnaire. Our sleep detection algorithm defined (nocturnal sleep as a period of sustained inactivity, itself detected as the absence of change in arm angle greater than 5 degrees for 5 minutes or more, during a period recorded as sleep by the participant in their sleep log. The resulting estimate of sleep duration had a moderate (but similar to previous findings agreement with questionnaire based measures for time in bed, defined as the difference between sleep onset and waking time (kappa = 0.32, 95%CI:0.29,0.34 and total sleep duration (kappa = 0.39, 0.36,0.42. This estimate was lower for time in bed for women, depressed participants, those reporting more insomnia symptoms, and on weekend days. No such group differences were found for total sleep duration. Our algorithm was validated against data from a polysomnography study on 28 persons which found a longer time window and lower angle threshold to have better sensitivity to wakefulness, while the reverse was true for sensitivity to sleep. The novelty of our method is the use of a generic algorithm that will allow comparison between studies rather than a "count" based, device specific method.

  6. Sandstone-type uranium deposits

    International Nuclear Information System (INIS)

    Finch, W.I.; Davis, J.F.

    1985-01-01

    World-class sandstone-type uranium deposits are defined as epigenetic concentrations of uranium minerals occurring as uneven impregnations and minor massive replacements primarily in fluvial, lacustrine, and deltaic sandstone formations. The main purpose of this introductory paper is to define, classify, and introduce to the general geologic setting for sandstone-type uranium deposits

  7. Sandstone Turning by Abrasive Waterjet

    Czech Academy of Sciences Publication Activity Database

    Hlaváček, Petr; Cárach, J.; Hloch, Sergej; Vasilko, K.; Klichová, Dagmar; Klich, Jiří; Lehocká, D.

    2015-01-01

    Roč. 48, č. 6 (2015), s. 2489-2493 ISSN 0723-2632 R&D Projects: GA MŠk ED2.1.00/03.0082; GA MŠk(CZ) LO1406 Institutional support: RVO:68145535 Keywords : turning away from the jet * conventional turning towards the jet * sandstone * abrasive water jet Subject RIV: JQ - Machines ; Tools Impact factor: 2.386, year: 2015 http://www.springerprofessional.de/sandstone-turning-by-abrasive-waterjet/6038028.html

  8. Sandstone-type uranium deposits

    International Nuclear Information System (INIS)

    Austin, S.R.; D'Andrea, R.F. Jr.

    1978-01-01

    Three overall factors are necessary for formation of uranium deposits in sandstone: a source of uranium, host rocks capable of transmitting uranium-bearing solutions, and a precipitant. Possible sources of uranium in sandstone-type deposits include groundwaters emanating from granitic highlands, arkosic sediments, tuffaceous material within or overlying the host rocks, connate fluids, and overlying black shales. The first three sources are considered the most likely. Host rocks are generally immature sandstones deposited in alluvial-fan, intermontane-basin or marginal-marine environments, but uranium deposits do occur in well-winnowed barrier-bar or eolian sands. Host rocks for uranium deposits generally show coefficients of permeability on the order of 1 to 100 gal/day/ft 2 . Precipitants are normally agents capable of reducing uranium from the uranyl to the uranous state. The association of uranium with organic matter is unequivocal; H 2 S, a powerful reductant, may have been present at the time of formation of some deposits but may go unnoticed today. Vanadium can serve to preserve the tabular characteristics of some deposits in the near-surface environment, but is considered an unlikely primary precipitant for uranium. Uranium deposits in sandstone are divided into two overall types: peneconcordant deposits, which occur in locally reducing environments in otherwise oxidized sandstones; and roll-type deposits, which occur at the margin of an area where an oxidized groundwater has permeated an otherwise reduced sandstone. Uranium deposits are further broken down into four subclasses; these are described

  9. Head Orientation Behavior of Users and Durations in Playful Open-Ended Interactions with an Android Robot

    DEFF Research Database (Denmark)

    Vlachos, Evgenios; Jochum, Elizabeth Ann; Schärfe, Henrik

    2016-01-01

    This paper presents the results of a field-experiment focused on the head orientation behavior of users in short-term dyadic interactions with an android (male) robot in a playful context, as well as on the duration of the interactions. The robotic trials took place in an art exhibition where...... subjects. The findings suggest that androids have the ability to maintain the focus of attention during short-term in-teractions within a playful context. This study provides an insight on how users communicate with an android robot, and on how to design meaningful human robot social interaction for real...

  10. Traces of the heritage arising from the Macelj sandstone

    Science.gov (United States)

    Golež, Mateja

    2014-05-01

    every house in the period between both World Wars. Only few masters succeeded in transferring their know-how to their descendants, which is why the local community has been making efforts to include the quarrying and working of the Macelj sandstone in educational workshops that are being carried out at the Open-Air Museum in Rogatec.

  11. Rate type isotach compaction of consolidated sandstone

    NARCIS (Netherlands)

    Waal, J.A. de; Thienen-Visser, K. van; Pruiksma, J.P.

    2015-01-01

    Laboratory experiments on samples from a consolidated sandstone reservoir are presented that demonstrate rate type compaction behaviour similar to that observed on unconsolidated sands and soils. Such rate type behaviour can have large consequences for reservoir compaction, surface subsidence and

  12. Experimental strain analysis of Clarens Sandstone colonised by endolithic lichens

    Directory of Open Access Journals (Sweden)

    D. Wessels

    1995-08-01

    Full Text Available Endolithic lichens occur commonly on Clarens Sandstone in South Africa, where they significantly contribute to the weathering of sandstone by means of mechanical and chemical weathering processes. This preliminary investigation reports on the success- ful use of strain gauges in detecting strain differences between sandstone without epilithic lichens and sandstone colonised by the euendolithic lichen Lecidea aff. sarcogynoides Korb. Mechanical weathering, expressed as strain changes, in Clarens Sandstone was studied during the transition from relatively dry winter to wet summer conditions. Daily weathering of sandstone due to thermal expansion and contraction of colonised and uncolonised sandstone could be shown. Our results show that liquid water in sandstone enhances the mechanical weathering of uncolonised Clarens Sandstone while water in the gaseous phase enhances mechanical weathering of sandstone by euendolithic lichens.

  13. "Sydney sandstone": Heritage Stone from Australia

    Science.gov (United States)

    Cooper, Barry; Kramar, Sabina

    2014-05-01

    Sydney is Australia's oldest city being founded in 1788. The city was fortunate to be established on an extensive and a relatively undeformed layer of lithified quartz sandstone of Triassic age that has proved to be an ideal building stone. The stone has been long identified by geologists as the Hawkesbury Sandstone. On the other hand the term "Sydney sandstone" has also been widely used over a long period, even to the extent of being utilised as the title of published books, so its formal designation as a heritage stone will immediately formalise this term. The oldest international usage is believed to be its use in the construction of the Stone Store at Kerikeri, New Zealand (1832-1836). In the late 19th century, public buildings such as hospitals, court houses as well as the prominent Sydney Town Hall, Sydney General Post Office, Art Gallery of New South Wales, State Library of New South Wales as well as numerous schools, churches, office building buildings, University, hotels, houses, retaining walls were all constructed using Sydney sandstone. Innumerable sculptures utilising the gold-coloured stone also embellished the city ranging from decorative friezes and capitals on building to significant monuments. Also in the late 19th and early 20th century, Sydney sandstone was used for major construction in most other major Australian cities especially Melbourne, Adelaide and Brisbane to the extent that complaints were expressed that suitable local stone materials were being neglected. Quarrying of Sydney sandstone continues today. In 2000 it was recorded noted that there were 33 significant operating Sydney sandstone quarries including aggregate and dimension stone operations. In addition sandstone continues to be sourced today from construction sites across the city area. Today major dimension stone producers (eg Gosford Quarries) sell Sydney sandstone not only into the Sydney market but also on national and international markets as cladding and paving products

  14. Return to work following robot-assisted laparoscopic and open retropubic radical prostatectomy: A single-center cohort study to compare duration of sick leave.

    Science.gov (United States)

    von Mechow, Stefanie; Graefen, Markus; Haese, Alexander; Tennstedt, Pierre; Pehrke, Dirk; Friedersdorff, Frank; Beyer, Burkhard

    2018-06-01

    To compare the duration of sick leave in patients with localized prostate cancer after robot-assisted radical prostatectomy (RARP) and open retropubic RP (ORP) at a German high-volume prostate cancer center. The data of 1,415 patients treated with RP at Martini Klinik, Prostate Cancer Center between 2012 and 2016 were, retrospectively, analyzed. Information on employment status, monthly revenues and days of work missed due to sickness were assessed via online questionnaire. Additional data were retrieved from our institutional database. Medians and interquartile ranges (IQR) were reported for continuous data. Cox proportional hazard analysis was performed to compare both surgical techniques for return to work time after RP. Median time elapsed between surgery and return to work comprised 42 days in patients undergoing RARP (IQR: 21-70) and ORP (IQR: 28-84, P = 0.05). In Cox regression analysis, surgical approach showed no impact on return to work time (RARP vs. ORP hazard ratio = 1, 95% CI: 0.91-1.16, P = 0.69). Return to work time was significantly associated with employment status, physical workload and monthly income (all PLimitation of this study is the nonrandomized design in a single-center. As the surgical approach did not show any influence on the number of days missed from work in patients undergoing RP, no superiority of either RARP or ORP could be identified for return to work time in a German cohort. Both surgical approaches are safe options usually allowing the patients to resume normal activities including work after an appropriate convalescence period. Copyright © 2018 Elsevier Inc. All rights reserved.

  15. Remifentanil-propofol analgo-sedation shortens duration of ventilation and length of ICU stay compared to a conventional regimen: A centre randomised, cross-over, open-label study in the Netherlands

    NARCIS (Netherlands)

    F.W. Rozendaal (Frans); P.E. Spronk (Peter); F.F. Snellen (Ferdinand); A. Schoen (Adri); A.R.H. van Zanten (Arthur); N.A. Foudraine (Norbert); P.G.H. Mulder (Paul); J. Bakker (Jan)

    2009-01-01

    textabstractObjective: Compare duration of mechanical ventilation (MV), weaning time, ICU-LOS (ICU-LOS), efficacy and safety of remifentanil-based regimen with conventional sedation and analgesia. Design: Centre randomised, open-label, crossover, 'real-life' study. Setting: 15 Dutch hospitals.

  16. Efficacy and safety of procalcitonin guidance in reducing the duration of antibiotic treatment in critically ill patients : a randomised, controlled, open-label trial

    NARCIS (Netherlands)

    de Jong, Evelien; van Oers, Jos A; Beishuizen, Albertus; Vos, Piet; Vermeijden, Wytze J; Haas, Lenneke E; Loef, Bert G; Dormans, Tom; van Melsen, Gertrude C; Kluiters, Yvette C; Kemperman, Hans; van den Elsen, Maarten J; Schouten, Jeroen A; Streefkerk, Jörn O; Krabbe, Hans G; Kieft, Hans; Kluge, Georg H; van Dam, Veerle C; van Pelt, Joost; Bormans, Laura; Otten, Martine Bokelman; Reidinga, Auke C; Endeman, Henrik; Twisk, Jos W; van de Garde, Ewoudt M W; de Smet, Anne Marie G A; Kesecioglu, Jozef; Girbes, Armand R; Nijsten, Maarten W; de Lange, Dylan W

    BACKGROUND: In critically ill patients, antibiotic therapy is of great importance but long duration of treatment is associated with the development of antimicrobial resistance. Procalcitonin is a marker used to guide antibacterial therapy and reduce its duration, but data about safety of this

  17. Effect of temperature on sandstone permeability

    DEFF Research Database (Denmark)

    Rosenbrand, Esther; Kjøller, Claus

    Hot water injection in geothermal sandstone aquifers is considered for seasonal energy storage in Denmark. However, an increase in the aquifer temperature might reduce permeability, and thereby increase production costs. An understanding of the factors that control permeability is required in order...... and the Klinkenberg procedure showed the expected correlation between the two measures, however, differences could be around one order of magnitude. In tight gas sandstones, permeability is often sensitive to net stress, which might change due to the pore pressure change in the Klinkenberg procedure. Besides...... affecting the Klinkenberg procedure, the combined effect of slip and changes in permeability would affect production during pressure depletion in tight gas sandstone reservoirs; therefore effects of gas slip and net stress on permeability were combined in a model based on the Klinkenberg equation. A lower...

  18. Clay squirt: Local flow dispersion in shale-bearing sandstones

    DEFF Research Database (Denmark)

    Sørensen, Morten Kanne; Fabricius, Ida Lykke

    2017-01-01

    Dispersion of elastic-wave velocity is common in sandstone and larger in shaly sandstone than in clean sandstone. Dispersion in fluid-saturated shaly sandstone often exceeds the level expected from the stress-dependent elastic moduli of dry sandstone. The large dispersion has been coined clay...... squirt and is proposed to originate from a pressure gradient between the clay microporosity and the effective porosity. We have formulated a simple model that quantifies the clay-squirt effect on bulk moduli of sandstone with homogeneously distributed shale laminae or dispersed shale. The model...... predictions were compared with the literature data. For sandstones with dispersed shale, agreement was found, whereas other sandstones have larger fluid-saturated bulk modulus, possibly due to partially load-bearing shales or heterogeneous shale distribution. The data that agree with the clay-squirt model...

  19. Petrography and geochemistry of Jurassic sandstones from the ...

    Indian Academy of Sciences (India)

    V Periasamy

    On the basis of geochemical results, sandstones are classified into arkose, ..... Geochemical classification diagram of sandstone samples from the Jhuran Formation based on log(SiO2/Al2O3)– ..... 1993) showing single trend for the Jhuran.

  20. PALEOEVIRONMENT OF NIGERIA'S AJALI SANDSTONES: A ...

    African Journals Online (AJOL)

    The Ajali Sandstone is a major clastic formation of Campanian-Maastrichtian age occuring within the Anambra Basin, Southeastern Nigeria. ... The result is in line with earlier conclusions of fluvial or fluviodeltaic depositional environment based on analysis of faceis, sedimentary rock which are suitable for morphometrical ...

  1. Characterizing flow pathways in a sandstone aquifer: Tectonic vs sedimentary heterogeneities

    Science.gov (United States)

    Medici, G.; West, L. J.; Mountney, N. P.

    2016-11-01

    Sandstone aquifers are commonly assumed to represent porous media characterized by a permeable matrix. However, such aquifers may be heavy fractured when rock properties and timing of deformation favour brittle failure and crack opening. In many aquifer types, fractures associated with faults, bedding planes and stratabound joints represent preferential pathways for fluids and contaminants. In this paper, well test and outcrop-scale studies reveal how strongly lithified siliciclastic rocks may be entirely dominated by fracture flow at shallow depths (≤ 180 m), similar to limestone and crystalline aquifers. However, sedimentary heterogeneities can primarily control fluid flow where fracture apertures are reduced by overburden pressures or mineral infills at greater depths. The Triassic St Bees Sandstone Formation (UK) of the East Irish Sea Basin represents an optimum example for study of the influence of both sedimentary and tectonic aquifer heterogeneities in a strongly lithified sandstone aquifer-type. This fluvial sedimentary succession accumulated in rapidly subsiding basins, which typically favours preservation of complete depositional cycles including fine grained layers (mudstone and silty sandstone) interbedded in sandstone fluvial channels. Additionally, vertical joints in the St Bees Sandstone Formation form a pervasive stratabound system whereby joints terminate at bedding discontinuities. Additionally, normal faults are present through the succession showing particular development of open-fractures. Here, the shallow aquifer (depth ≤ 180 m) was characterized using hydro-geophysics. Fluid temperature, conductivity and flow-velocity logs record inflows and outflows from normal faults, as well as from pervasive bed-parallel fractures. Quantitative flow logging analyses in boreholes that cut fault planes indicate that zones of fault-related open fractures characterize 50% of water flow. The remaining flow component is dominated by bed-parallel fractures

  2. PETROFACIES CHARACTERISTICS OF THE SANDSTONES OF THE UPPER MIOCENELOWER PLIOCENE AGED IN THE ULUMUHSİNE-TATKÖY (KONYA AREA

    Directory of Open Access Journals (Sweden)

    A. Müjdat ÖZKAN

    2000-03-01

    Full Text Available In the study area, Upper Miocene-Lower Pliocene aged Ulumuhsine formation, was formed in a shallow, open lake and river environment. The lithologies of this formation are thin-medium bedded, laminated and fossil rich limestone, thin-thick bedded mudstone, thin-thick bedded marl, thin-thick bedded dolomite with stromatolite interbedded limestone, tuffite, chert bands and coal-rich levels. In addition, it includes conglomerates and sandstones of underwater distrubution channels in lacustrine, and channel and bar sediments in stream environments. Red, gray, rarely green colored sandstones are thin-thick bedded, and in some levels well sorting, in some levels proorly sorting. They present sedimentary structures, as graded, herringbone cross-bedding, symmetric ripple-marks, and laminate. Sandstones are named lithic arenite and lithic graywacke and litharenite, feldspathic litharenite and sublithic arenite. These sandstones are rich rock fragments and quartzs, in addition they contain plagioclase, biotite, muskovite, opaque mineral and epidote. Binding materials of sandstones are mainly calcite cements and clay matrix, and iron oxide cement in little amount. From the mineralogical and textural point of view. As a tectonic environment, the main source of sandstones are recycled orogen (thrust, collision and land uplift and recyded lithic fragments.

  3. Radionuclide transport in sandstones with WIPP brine

    International Nuclear Information System (INIS)

    Weed, H.C.; Bazan, F.; Fontanilla, J.; Garrison, J.; Rego, J.; Winslow, A.M.

    1981-02-01

    Retardation factors (R) have been measured for the transport of 3 H, /sup 95m/Tc, and 85 Sr in WIPP brine using St. Peter, Berea, Kayenta, and San Felipe sandstone cores. If tritium is assumed to have R=1, /sup 95m/Tc has R=1.0 to 1.3 and therefore is essentially not retarded. Strontium-85 has R = 1.0 to 1.3 on St. Peter, Berea, and Kayenta, but R=3 on San Felipe. This is attributed to sorption on the matrix material of San Felipe, which has 45 volume % matrix compared with 1 to 10 volume % for the others. Retardation factors (R/sub s/) for 85 Sr calculated from static sorption measurements are unity for all the sandstones. Therefore, the static and transport results for 85 Sr disagree in the case of San Felipe, but agree for St. Peter, Berea, and Kayenta

  4. Performance of Different Acids on Sandstone Formations

    Directory of Open Access Journals (Sweden)

    M. A. Zaman

    2013-12-01

    Full Text Available Stimulation of sandstone formations is a challenging task, which involves several chemicals and physical interactions of the acid with the formation. Some of these reactions may result in formation damage. Mud acid has been successfully used to stimulate sandstone reservoirs for a number of years. It is a mixture of hydrofluoric (HF and hydrochloric (HCl acids designed to dissolve clays and siliceous fines accumulated in the near-wellbore region. Matrix acidizing may also be used to increase formation permeability in undamaged wells. The change may be up to 50% to 100% with the mud acid. For any acidizing process, the selection of acid (Formulation and Concentration and the design (Pre-flush, Main Acid, After-flush is very important. Different researchers are using different combinations of acids with different concentrations to get the best results for acidization. Mainly the common practice is combination of Hydrochloric Acid – Hydrofluoric with Concentration (3% HF – 12% HCl. This paper presents the results of a laboratory investigation of Orthophosphoric acid instead of hydrochloric acid in one combination and the second combination is Fluoboric and formic acid and the third one is formic and hydrofluoric acid. The results are compared with the mud acid and the results calculated are porosity, permeability, and FESEM Analysis and Strength tests. All of these new combinations shows that these have the potential to be used as acidizing acids on sandstone formations.

  5. Cathodoluminescence characteristics of sandstone and the implications for sandstone type No. 512 uranium deposit

    International Nuclear Information System (INIS)

    Liu Xiaodong; Guan Taiyang

    1998-12-01

    Cathodoluminescence (CL) technique, as a special petrologic tool, has been applied to the studies of uranium hosted sandstone from No. 512 uranium deposit located in Xinjiang Autonomous Region, Northwest China. The detrital grains including quartz, feldspar, debris and cements display distinguishing CL properties. The quartz grains mainly demonstrate brown and dark blue CL, feldspar grains demonstrate blue and bright blue CL, calcite cement displays bright yellow-orange and orange-red CL with significant CL zoning, while the debris, mud and sand cements have dark red CL, multicolor CL or non-luminescence. The characteristics of overgrowth, fracture healing, and the original contact relations of detrital grains appear much more significant with CL than that with conventional visual methods. Much more information can be contributed by CL technique to decipher the provenance area, to explain the cementation, consolidation and other diagenesis processes of sandstone. The CL technique also provides and efficient tool for identifying detrital grains and cements, and for more precisely estimating the proportions of various detrital grains and cement components in sandstone. The CL emission of uranium hosted sandstone revealed the existence of radiation-damage rims of quartz grains at the places with a little or no uranium minerals nearby, which may imply a uranium-leaching episode during the diagenesis of sandstone

  6. INAA and petrological study of sandstones from the Angkor monuments

    International Nuclear Information System (INIS)

    Kucera, J.; Kranda, K.; Soukal, L.; Novak, J.K.; Lang, M.; Poncar, J.; Krausova, I.; Cunin, O.

    2008-01-01

    We determined 35 major, minor and trace elements in sandstone samples taken from building blocks of 19 Angkor temples and from an old and a new quarry using INAA. We also characterized the sandstone samples with conventional microscopy and electron microprobe analysis. Using cluster analysis, we found no straightforward correlation between the chemical/petrological properties of the sandstones and a presumed period of individual temples construction. The poor correlation may result either from the inherent inhomogeneity of sandstone or just reflect the diversity of quarries that supplied building blocks for the construction of any particular temple. (author)

  7. The migration of uranium through sandstone

    International Nuclear Information System (INIS)

    Bennett, D.G.; Read, D.; Lawless, T.A.; Sims, R.J.

    1992-01-01

    Three column experiments are described in which the migration of uranium through Clashach Sandstone was studied. A priori predictions of uranium migration in the experiments were made using an equilibrium chemical transport model. The experimental results showed that, even under oxidising conditions, the migration of uranium is strongly retarded owing to the affinity of uranium for mineral surfaces. For the relatively simple chemical system investigated, the chemical transport model was successful in predicting the migration of uranium and its distribution along the column. (author)

  8. Examples from the 1.6 Ga Chorhat Sandstone, Vindhyan

    Indian Academy of Sciences (India)

    This paper addresses macroscopic signatures of microbial mat-related structures within the 1.6 Ga-old Chorhat Sandstone of the Semri Group –the basal stratigraphic unit of the Vindhyan succession in Son valley.The Chorhat Sandstone broadly represents a prograding succession of three depositional facies ranging from ...

  9. Geothermal characteristics of Buntsandstein sandstone reservoir of Alsace

    International Nuclear Information System (INIS)

    Haffen, Sebastien

    2012-01-01

    The Buntsandstein, located in the Upper Rhine Graben, appears to be an easy target for geothermal exploitation, linking sandstone and clay with the regional thermal anomaly. This study aims at characterizing petrophysical characteristics of these sandstones as well as the fracturing affecting them, with the intention of providing a conceptual model of the formation which will act as guide for future exploitation. The sedimentary facies are composed by five petrographical facies (clean sandstones, sandstones with clayey coating, clay matrix sandstones, silicified sandstones and carbonated matrix sandstones) which split with variable proportions and control a part of petrophysical properties measured at matrix scale. The comparison between petrophysical data, macroscopic data from temperature gradient analysis, modelling data and fracturing, allows the building of a Buntsandstein Sandstones fluids circulation conceptual model. This analysis points the role of the damage zone of fault zones for fluids transfer at large scale, but also that of two sedimentary facies: marginal erg and Playa Lake. The analysis of different outcrops shows that the fracturing evolves according to the situation in the sedimentary pile and according to the situation in comparison with major tectonic accidents. (author) [fr

  10. INTRODUCTION Sandstone beds within Auchi locality are the ...

    African Journals Online (AJOL)

    The major framework composition is Q F L which classifies the sandstone as Quartz ... The grains are texturally immature as depicted by their subangular edges but mineralogically ..... Fig 6 : Vertical Section of Bioturbated Sandstone Lithofacies Showing Trace Fossils ..... on Water Quality and Planktonic Production in an.

  11. Sediment transport direction in fluviatile Karharbari sandstone, Giridih Basin, Bihar

    Energy Technology Data Exchange (ETDEWEB)

    Tewari, R C; Casshyap, S M

    1978-01-01

    The sandstone is pebbly, very coarse grained in the lower part, and coarse to medium grained in the upper part. Shale and coal respectively constitute 9 and 5% of the strata Small and large erosional channels and successive sets of large scale cross-bedding characterize the sandstone. Palaeo- currents reveal that the paleodrainage and sediment transport were dominantly directed from SSW to NNE.

  12. Sandstone landforms shaped by negative feedback between stress and erosion

    Czech Academy of Sciences Publication Activity Database

    Bruthans, J.; Soukup, J.; Vaculíková, J.; Filippi, Michal; Schweigstillová, Jana; Mayo, A. L.; Mašín, D.; Kletetschka, Günther; Řihošek, J.

    2014-01-01

    Roč. 7, č. 8 (2014), s. 597-601 ISSN 1752-0894 R&D Projects: GA ČR GA13-28040S Institutional support: RVO:67985831 ; RVO:67985891 Keywords : sandstone * sandstone landsforms * stress * erosion Subject RIV: DB - Geology ; Mineralogy Impact factor: 11.740, year: 2014

  13. Effect of drilling fluids on permeability of uranium sandstone. Report of Investigations/1984

    International Nuclear Information System (INIS)

    Ahlness, J.K.; Johnson, D.I.; Tweeton, D.R.

    1984-01-01

    The Bureau of Mines conducted laboratory and field experiments to determine the amount of permeability reduction in uranium sandstone after its exposure to different drilling fluids. Seven polymer and two bentonite fluids were laboratory-tested in their clean condition, and six polymer fluids were tested with simulated drill cuttings added. Sandstone cores cut from samples collected at an open pit uranium mine were the test medium. The clean fluid that resulted in the least permeability reduction was an hydroxyethyl cellulose polymer fluid. The greatest permeability reduction of the clean polymers came from a shale-inhibiting synthetic polymer. Six polymer fluids were tested with simulated drill cuttings added to represent field use. The least permeability reduction was obtained from a multi-polymer blend fluid. A field experiment was performed to compare how two polymer fluids affect formation permeability when used for drilling in situ uranium leaching wells

  14. Hydrological modelling in sandstone rocks watershed

    Science.gov (United States)

    Ponížilová, Iva; Unucka, Jan

    2015-04-01

    The contribution is focused on the modelling of surface and subsurface runoff in the Ploučnice basin. The used rainfall-runoff model is HEC-HMS comprising of the method of SCS CN curves and a recession method. The geological subsurface consisting of sandstone is characterised by reduced surface runoff and, on the contrary, it contributes to subsurface runoff. The aim of this paper is comparison of the rate of influence of sandstone on reducing surface runoff. The recession method for subsurface runoff was used to determine the subsurface runoff. The HEC-HMS model allows semi- and fully distributed approaches to schematisation of the watershed and rainfall situations. To determine the volume of runoff the method of SCS CN curves is used, which results depend on hydrological conditions of the soils. The rainfall-runoff model assuming selection of so-called methods of event of the SCS-CN type is used to determine the hydrograph and peak flow rate based on simulation of surface runoff in precipitation exceeding the infiltration capacity of the soil. The recession method is used to solve the baseflow (subsurface) runoff. The method is based on the separation of hydrograph to direct runoff and subsurface or baseflow runoff. The study area for the simulation of runoff using the method of SCS CN curves to determine the hydrological transformation is the Ploučnice basin. The Ploučnice is a hydrologically significant river in the northern part of the Czech Republic, it is a right tributary of the Elbe river with a total basin area of 1.194 km2. The average value of CN curves for the Ploučnice basin is 72. The geological structure of the Ploučnice basin is predominantly formed by Mesozoic sandstone. Despite significant initial loss of rainfall the basin response to the causal rainfall was demonstrated by a rapid rise of the surface runoff from the watershed and reached culmination flow. Basically, only surface runoff occures in the catchment during the initial phase of

  15. Anatomy of an ancient aeolian sandstone on Mars: the Stimson formation, Gale crater, Mars

    Science.gov (United States)

    Gupta, Sanjeev; Banham, Steven; Rubin, David; Watkins, Jessica; Sumner, Dawn; Grotzinger, John P.; Lewis, Kevin; Edgett, Kenneth S.; Edgar, Lauren; Stack, Kathryn; Day, McKenzie; Ewing, Ryan; Lapotre, Mathieu

    2016-10-01

    Since landing in 2012, the Mars Science Laboratory's (MSL) rover Curiosity has traversed the plains and foothills of Aeolis Mons (informally known as Mt. Sharp) investigating the environments preserved in the stratigraphic record of Gale crater. Recently, the Curiosity team has been investigating the Stimson formation, a sandstone exhibiting abundant crossbedding that drapes the underlying Murray formation mudstones. The contact between the Stimson and underlying Murray formation exhibits several meters relief over several 100 m hundred metres where encountered thus far. The Stimson is observed to onlap onto this contact, indicating that accumulating Stimson sandstones unconformably onlapped or buried local palaeotopography.Facies and architectural elements observed within the Stimson are interpreted to represent deposition within an ancient dune field. The Stimson formation is typically composed of decimeter-scale and meter-scale crossbedded sandstones, (exhibiting wind-ripple lamination and well rounded particles up to granule size). Architectural elements are visible in outcrops oriented perpendicular to the regional northwest dip. These consist of undulating surfaces parallel to the regional dip with observed lateral extents up to 30 m that truncate underlying cross-sets and commonly act as basal surfaces to overlying cross-sets. Undulating surfaces are interpreted possibly to be deflationary supersurfaces, which formed in response to deflation or dune-field stabilisation across a regional extent. Surfaces inclined relative to the regional dip ascend between supersurfaces towards the north east at an observed angle of 3-4°. These surfaces are interpreted to be dune bounding surfaces, which are preserved when dunes climb as a result of dune-field aggradation. Aggradation of the system during the duration of the dune field's existence possibly occurred as a response to episodic increases of sediment supply into the basin, allowing dunes to climb and preserving

  16. Relationship between characteristics of fan-delta sandstone bodies and in-situ leachable sandstone-type uranium mineralization

    International Nuclear Information System (INIS)

    Nie Fengjun; Zhou Weixun; Guan Taiyang; Li Sitian

    2000-01-01

    Like normal deltas, fan-deltas are composed of three parts, i.e., fan-delta plain, fan-delta front and pre-fin-delta, In-situ leachable uranium deposits are commonly distributed along the margins of in-land basins. The author analyzes the possible relationship between the basic characteristics of fan-delta sandstone bodies and uranium mineralization. Two examples, e.g., the fan delta depositional systems in the eastern part of Jungger basin and the southern part of Yili basin, are given to illustrate the fan-delta vertical sequence and planar distribution of sedimentary facies. It has been pointed out that the braided channel sandstone bodies on delta plain, sub-aqueous distributional channel sandstone bodies and delta front sandstone bodies may be the favourable host rocks for in-situ leachable sandstone uranium deposits

  17. Towards a typology of the mares sandstone of Mallorca Concept, characterization and stratigraphy

    International Nuclear Information System (INIS)

    Mas Gornals, C.

    2017-01-01

    The mares sandstone has traditionally been the most representative and characteristic building stone on the island of Mallorca, used practically exclusively as construction material for centuries, since the abandonment of stone-and-mortar walls, until its progressive disuse with the appearance of the re-enforced concrete, which finally eclipsed its use. Such emblematic buildings for the island, as Bellver Castle, the Cathedral, La Lonja or the old city walls of Palma, bear witness to this. In Mallorca, the mares sandstone is quarried in the open air or in subterranean galleries. Vernacular architecture has always used the most accessible appropriate materials, and in the case of the mares sandstone, its abundance, sufficient softness, which facilitates its extraction, Together with sufficient hardness to confer solidity and durability in constructions, converge. The lack of specific scientific and geological data published about the different types of mares in Mallorca, added to the recent resurgence of technical, applied and landscape interest in this stone, have made a revision of its definition, characterization and classification necessary. [es

  18. Nodular features from Proterozoic Sonia Sandstone, Jodhpur Group ...

    Indian Academy of Sciences (India)

    Corresponding author. e-mail: parthageology@gmail.com. The Sonia ..... cement variety in the form of dispersed dark brown clots and .... content within the nodule sandstones bear sig- nature in ..... Carbonates and Evaporites 21 133–143.

  19. provenance of sandstone on the western flank of anambra basin

    African Journals Online (AJOL)

    HP

    GLOBAL JOURNAL OF GEOLOGICAL SCIENCES VOL. 14, 2016: 13-21. COPYRIGHT© ... from Fugar locality. The sandstones each classify as quartz arenites and sublitharenites. ... Tectonic movement in the Santonian times resulted in the ...

  20. Characterization of application of acu sandstone in ceramic mass

    International Nuclear Information System (INIS)

    Nobrega, L.F.P.M.; Souza, M.M.; Gomes, Y.S.; Fernandes, D.L.

    2016-01-01

    The sandstone is a sedimentary rock formed mainly by quartz grains. In Rio Grande do Norte, there is the Potiguar Basin with the Jandaira and Acu Formations. The latter consists of thick layers of whitish-colored sandstones. It stands out as a water storage facility in the state, but it is also used for building aggregates. This article aimed at the use of the sandstone of this formation in the ceramic mass for coating. Initially, the material was sampled. It went through the comminution process to achieve the required granulometry. After this, three formulations were made to incorporate this new material into the traditional ones. The methods were performed according to ISO 13816. After sintering at 1200 °C, the specimens were subjected to the physical tests. A positive result was obtained for the use of the Acu sandstone in low concentrations. It is clear, therefore, its use in ceramics for coating

  1. Transport of silver nanoparticles in single fractured sandstone

    Science.gov (United States)

    Neukum, Christoph

    2018-02-01

    Silver nanoparticles (Ag-NP) are used in various consumer products and are one of the most prevalent metallic nanoparticle in commodities and are released into the environment. Transport behavior of Ag-NP in groundwater is one important aspect for the assessment of environmental impact and protection of drinking water resources in particular. Ag-NP transport processes in saturated single-fractured sandstones using triaxial flow cell experiments with different kind of sandstones is investigated. Ag-NP concentration and size are analyzed using flow field-flow fractionation and coupled SEM-EDX analysis. Results indicate that Ag-NP are more mobile and show generally lower attachment on rock surface compared to experiments in undisturbed sandstone matrix and partially fractured sandstones. Ag-NP transport is controlled by the characteristics of matrix porosity, time depending blocking of attachment sites and solute chemistry. Where Ag-NP attachment occur, it is heterogeneously distributed on the fracture surface.

  2. Natural Erosion of Sandstone as Shape Optimisation.

    Science.gov (United States)

    Ostanin, Igor; Safonov, Alexander; Oseledets, Ivan

    2017-12-11

    Natural arches, pillars and other exotic sandstone formations have always been attracting attention for their unusual shapes and amazing mechanical balance that leave a strong impression of intelligent design rather than the result of a stochastic process. It has been recently demonstrated that these shapes could have been the result of the negative feedback between stress and erosion that originates in fundamental laws of friction between the rock's constituent particles. Here we present a deeper analysis of this idea and bridge it with the approaches utilized in shape and topology optimisation. It appears that the processes of natural erosion, driven by stochastic surface forces and Mohr-Coulomb law of dry friction, can be viewed within the framework of local optimisation for minimum elastic strain energy. Our hypothesis is confirmed by numerical simulations of the erosion using the topological-shape optimisation model. Our work contributes to a better understanding of stochastic erosion and feasible landscape formations that could be found on Earth and beyond.

  3. Failure Forecasting in Triaxially Stressed Sandstones

    Science.gov (United States)

    Crippen, A.; Bell, A. F.; Curtis, A.; Main, I. G.

    2017-12-01

    Precursory signals to fracturing events have been observed to follow power-law accelerations in spatial, temporal, and size distributions leading up to catastrophic failure. In previous studies this behavior was modeled using Voight's relation of a geophysical precursor in order to perform `hindcasts' by solving for failure onset time. However, performing this analysis in retrospect creates a bias, as we know an event happened, when it happened, and we can search data for precursors accordingly. We aim to remove this retrospective bias, thereby allowing us to make failure forecasts in real-time in a rock deformation laboratory. We triaxially compressed water-saturated 100 mm sandstone cores (Pc= 25MPa, Pp = 5MPa, σ = 1.0E-5 s-1) to the point of failure while monitoring strain rate, differential stress, AEs, and continuous waveform data. Here we compare the current `hindcast` methods on synthetic and our real laboratory data. We then apply these techniques to increasing fractions of the data sets to observe the evolution of the failure forecast time with precursory data. We discuss these results as well as our plan to mitigate false positives and minimize errors for real-time application. Real-time failure forecasting could revolutionize the field of hazard mitigation of brittle failure processes by allowing non-invasive monitoring of civil structures, volcanoes, and possibly fault zones.

  4. Electrical conductivity of sandstone, limestone, and granite

    Energy Technology Data Exchange (ETDEWEB)

    Duba, A.; Piwinskii, A.J.; Santor, M.; Weed, H.C.

    1978-01-01

    The electrical conductivity of cylindrical cores of Westerly granite, Indiana limestone and Nugget, St Peter and Kayenta sandstones was measured at about 25/sup 0/C in vacuo, in air, and after saturation in distilled water, tap water, and 0.1 M NaCl solution. The three-electrode technique with a guard ring and the two-electrode technique without a guard ring were used. Core aspect ratio over the range of 2.00 to 0.25, as well as frequency over the range of 50 Hz to 10 kHz, influences the conductivity of all rocks, especially those measured in vacuo. Measurements from water-saturated samples using a guard ring are not appreciably different from those obtained without a guard ring. The conductivity of rocks saturated in 0.1 M NaCl solution changes least with a change in aspect ratio; for these rocks a linear relationship, known as Archie's Law, exists between log porosity and log conductivity. No simple correlation was found between those factors in rocks saturated with tap or distilled water. Thus, it appears Archie's Law is of questionable value for correlating laboratory data from rocks saturated with low-conductivity fluids.

  5. Applying reaction condition index to predict sandstone type uranium deposit

    International Nuclear Information System (INIS)

    Chen Gongxin; Liu Jinhui; Cheng Hai

    2002-01-01

    On the basic of the explanation of reaction condition index, the deduction of reaction condition index calculation principle, the hydrogeological setting in Gongpoquan basin in Baishan, Gansu province and the study of reaction condition index of its water source point, the north Luotuoquan area in Gongpoquan basin seems to be a favourable place for sandstone type uranium deposit, and the prospect area for sandstone type uranium deposit is delimitated

  6. Micropore Structure Representation of Sandstone in Petroleum Reservoirs Using an Atomic Force Microscope

    International Nuclear Information System (INIS)

    Bai Yong-Qiang; Zhu Xing; Wu Jun-Zheng; Bai Wen-Guang

    2011-01-01

    The pore structure of sandstone in an oil reservoir is investigated using atomic force microscopy (AFM). At nanoscale resolution, AFM images of sandstone show us the fine structure. The real height data of images display the three-dimensional space structure of sandstone effectively. The three-dimensional analysis results show that the AFM images of sandstone have unique characteristics that, like fingerprints, can identify different structural properties of sandstones. The results demonstrate that AFM is an effective method used to represent original sandstone in petroleum reservoirs, and may help geologists to appreciate the sandstone in oil reservoirs fully. (general)

  7. Channel sandstone and bar morphology of the Beaufort group uranium district near Beaufort West

    International Nuclear Information System (INIS)

    Stear, W.M.

    1980-01-01

    Sheet-like and lenticular sandstone bodies in the Lower Beaufort Group (Adelaide Subgroup) uranium district occur in megacyclic repetition as superimposed systems of ephemeral fluvial channels that display characteristics of complex lateral and vertical accretion. Channel sandstone bodies are defined on morphological grounds into two types. Sheet sandstone bodies are the commonest type and comprise the bulk of sandstone packages in arenaceous zones of megacycles. Composite sandstone sheets result from multilateral coalescence of individual sandstone bodies. Isolated lenticular sandstone units in argillaceous zones of megacycles comprise sheet and ribbon sandstone types. Multi-storeying is a prominent feature of most channel sandstone bodies and often results in local sandstone thickening. Bedforms relate to the formation of compound bars and record periods of dynamic accretion and erosion. Rarely preserved palaeosurfaces vividly illustrate the fluctuating hydrodynamic conditions that typified ephemeral fluvial sedimentation in a semi-arid environment during Lower Beaufort times

  8. Channel sandstone and bar morphology of the Beaufort group uranium district near Beaufort West

    Energy Technology Data Exchange (ETDEWEB)

    Stear, W M

    1980-01-01

    Sheet-like and lenticular sandstone bodies in the Lower Beaufort Group (Adelaide Subgroup) uranium district occur in megacyclic repetition as superimposed systems of ephemeral fluvial channels that display characteristics of complex lateral and vertical accretion. Channel sandstone bodies are defined on morphological grounds into two types. Sheet sandstone bodies are the commonest type and comprise the bulk of sandstone packages in arenaceous zones of megacycles. Composite sandstone sheets result from multilateral coalescence of individual sandstone bodies. Isolated lenticular sandstone units in argillaceous zones of megacycles comprise sheet and ribbon sandstone types. Multi-storeying is a prominent feature of most channel sandstone bodies and often results in local sandstone thickening. Bedforms relate to the formation of compound bars and record periods of dynamic accretion and erosion. Rarely preserved palaeosurfaces vividly illustrate the fluctuating hydrodynamic conditions that typified ephemeral fluvial sedimentation in a semi-arid environment during Lower Beaufort times.

  9. Sensing, Measuring and Modelling the Mechanical Properties of Sandstone

    Science.gov (United States)

    Antony, S. J.; Olugbenga, A.; Ozerkan, N. G.

    2018-02-01

    We present a hybrid framework for simulating the strength and dilation characteristics of sandstone. Where possible, the grain-scale properties of sandstone are evaluated experimentally in detail. Also, using photo-stress analysis, we sense the deviator stress (/strain) distribution at the micro-scale and its components along the orthogonal directions on the surface of a V-notch sandstone sample under mechanical loading. Based on this measurement and applying a grain-scale model, the optical anisotropy index K 0 is inferred at the grain scale. This correlated well with the grain contact stiffness ratio K evaluated using ultrasound sensors independently. Thereafter, in addition to other experimentally characterised structural and grain-scale properties of sandstone, K is fed as an input into the discrete element modelling of fracture strength and dilation of the sandstone samples. Physical bulk-scale experiments are also conducted to evaluate the load-displacement relation, dilation and bulk fracture strength characteristics of sandstone samples under compression and shear. A good level of agreement is obtained between the results of the simulations and experiments. The current generic framework could be applied to understand the internal and bulk mechanical properties of such complex opaque and heterogeneous materials more realistically in future.

  10. Humid to arid to subhumid vegetation shift on Pilliga Sandstone, Ulungra Springs, New South Wales

    Science.gov (United States)

    Dodson, J. R.; Wright, R. V. S.

    1989-09-01

    The Pilliga Sandstone region of the northwest slope of New South Wales has a natural vegetation cover of sclerophyllous relatively closed to open forests with a largely heathy understorey, and a warm, subhumid and continental climate. Pollen analysis of spring-fed deposits gives a vegetation history extending from at least 30,000 yr B.P. to the late Holocene. Tree pollen became scarce after about 25,000 yr B.P. and an assemblage dominated by Chenopodiaceae, Liguliflorae, Tubuliflorae, and probably Poaceae developed. No similar assemblage is known from present pollen rain studies carried out in Australia. However, it clearly represents a treeless open shrub-steppe formation and therefore an arid or semiarid environment. The site thus provides evidence of an eastward late Pleistocene extension of the arid zone in Australia, and is the first full-glacial vegetation record between 20° and 35° latitude in Australia. The present vegetation cover did not become reestablished until the beginning of the Holocene, which raises questions about the form in which Pilliga Sandstone vegetation survived full-glacial conditions.

  11. Geological principles of exploration for sandstone-hosted uranium deposits

    International Nuclear Information System (INIS)

    Le Roux, J.P.

    1982-10-01

    Although the importance of sandstone-hosted uranium deposits has seemingly faded in recent years due to the discovery of large, high -grade deposits elsewhere, a forecasted energy shortage in the near future will probably necessitate a new look at sedimentary basins as a source of uranium. Back-arc basins adjacent to calcalkaline source areas are especially favourable if they are filled with fluvial, post-Devonian sediments. Syn- and post-depositional tectonics play an important role in the sedimentation-mineralisation process and should be investigated. The oxidation-reduction state of the sandstones is a valid prospecting tool. Sedimentological environments govern the permeability and vegetal matter content of sandstones and directly control uranium mineralisation

  12. Electrokinetic desalination of sandstones for NaCl removal

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Christensen, Iben V.

    2012-01-01

    of reliable methods to remove the damaging salts in order to stop the decay. Electrokinetic desalination of fired clay bricks have previously shown efficient in laboratory scale and in the present work the method is tested for desalination of Cotta and Posta sandstones, which both have lower porosity than...... each stone, but electroosmosis in the poultices may have caused suction/pressure over the interface between stone and poultice causing the differences in poultice water content. The transport numbers for Cl− and Na+ differed in the two stones and were highest in the most porous Cotta sandstone in spite...... of similar high pore water concentrations and the same applied electric current. The hypotheses is that a layered structure of the sandstones could be the cause for this, as the electric current may preferentially flow in certain paths through the stone, which are thus desalinated first. After...

  13. On the migration of uranium isotopes in sandstone aquifers

    International Nuclear Information System (INIS)

    Froehlich, K.; Gellermann, R.

    1982-01-01

    Measurements of natural 238 U and 234 U activity in groundwater of sandstone aquifers have been used to study the migration of these uranium isotopes. Regarding the uranium exchange between liquid phase and rock surface during migration, two different models were applied for evaluating the experimental results. Values of corresponding parameters (retardation factor K, removal rate R) reflecting different behaviour concerning this exchange were determined. For example, the values obtained for 238 U in a Triassic sandstone aquifer of the GDR are K = 8.6 x 10 6 and R = 1.3 x 10 -3 a -1 , respectively. It was found that, under the conditions of the sandstone aquifer concerned, the removal rate model is better suited for calculating uranium-isotope migration in groundwater. (author)

  14. Diagenetic effect on permeabilities of geothermal sandstone reservoirs

    DEFF Research Database (Denmark)

    Weibel, Rikke; Olivarius, Mette; Kristensen, Lars

    The Danish subsurface contains abundant sedimentary deposits, which can be utilized for geothermal heating. The Upper Triassic – Lower Jurassic continental-marine sandstones of the Gassum Formation has been utilised as a geothermal reservoir for the Thisted Geothermal Plant since 1984 extracting...... and permeability is caused by increased diagenetic changes of the sandstones due to increased burial depth and temperatures. Therefore, the highest water temperatures typically correspond with the lowest porosities and permeabilities. Especially the permeability is crucial for the performance of the geothermal......-line fractures. Continuous thin chlorite coatings results in less porosity- and permeability-reduction with burial than the general reduction with burial, unless carbonate cemented. Therefore, localities of sandstones characterized by these continuous chlorite coatings may represent fine geothermal reservoirs...

  15. Reservoir characterization of the Mt. Simon Sandstone, Illinois Basin, USA

    Science.gov (United States)

    Frailey, S.M.; Damico, J.; Leetaru, H.E.

    2011-01-01

    The integration of open hole well log analyses, core analyses and pressure transient analyses was used for reservoir characterization of the Mt. Simon sandstone. Characterization of the injection interval provides the basis for a geologic model to support the baseline MVA model, specify pressure design requirements of surface equipment, develop completion strategies, estimate injection rates, and project the CO2 plume distribution.The Cambrian-age Mt. Simon Sandstone overlies the Precambrian granite basement of the Illinois Basin. The Mt. Simon is relatively thick formation exceeding 800 meters in some areas of the Illinois Basin. In the deeper part of the basin where sequestration is likely to occur at depths exceeding 1000 m, horizontal core permeability ranges from less than 1 ?? 10-12 cm 2 to greater than 1 ?? 10-8 cm2. Well log and core porosity can be up to 30% in the basal Mt. Simon reservoir. For modeling purposes, reservoir characterization includes absolute horizontal and vertical permeability, effective porosity, net and gross thickness, and depth. For horizontal permeability, log porosity was correlated with core. The core porosity-permeability correlation was improved by using grain size as an indication of pore throat size. After numerous attempts to identify an appropriate log signature, the calculated cementation exponent from Archie's porosity and resistivity relationships was used to identify which porosity-permeability correlation to apply and a permeability log was made. Due to the relatively large thickness of the Mt. Simon, vertical permeability is an important attribute to understand the distribution of CO2 when the injection interval is in the lower part of the unit. Only core analyses and specifically designed pressure transient tests can yield vertical permeability. Many reservoir flow models show that 500-800 m from the injection well most of the CO2 migrates upward depending on the magnitude of the vertical permeability and CO2 injection

  16. Regional distribution regularity of sandstone uranium deposits in Asian continent and prospecting strategy for sandstone uranium deposits in China

    International Nuclear Information System (INIS)

    Chen Zuyi

    2002-01-01

    Since the 1980's, after the discovery of numerous sandstone uranium deposits in Middle Asia (Kazakhstan, Uzbekistan) many large sandstone uranium deposits have been found in both Russia and Mongolia. So that Asia has become the most concentrated region of sandstone uranium deposits. The known sandstone uranium deposits occur mostly in a arcual tectonic belt constrained from the north by the Siberian continental block, and the Tarim-North China continental block from the south. This belt is named by Russian geologists as the Central Asian Mobile Belt, and some Chinese geologists call it the 'Mongolian Arc'. A lot of large and super large metallic, non-metallic, gold, polymetallic, porphyry copper and gold, massive sulphide and uranium deposits (of sandstone and volcanic types) with different origin and various types concentrated occur in this belt. The abundant and colourful mineral resources in the region are closely associated with the specific geologic-tectonic evolution of the above belt. It is necessary to strengthen the detailed geologic research and uranium prospecting in the region

  17. Fluvial-deltaic sedimentation and stratigraphy of the ferron sandstone

    Science.gov (United States)

    Anderson, P.B.; Chidsey, T.C.; Ryer, T.A.

    1997-01-01

    East-central Utah has world-class outcrops of dominantly fluvial-deltaic Turonian to Coniacian aged strata deposited in the Cretaceous foreland basin. The Ferron Sandstone Member of the Mancos Shale records the influences of both tidal and wave energy on fluvial-dominated deltas on the western margin of the Cretaceous western interior seaway. Revisions of the stratigraphy are proposed for the Ferron Sandstone. Facies representing a variety of environments of deposition are well exposed, including delta-front, strandline, marginal marine, and coastal-plain. Some of these facies are described in detail for use in petroleum reservoir characterization and include permeability structure.

  18. Sandstone-type uranium deposits. Summary and conclusions

    International Nuclear Information System (INIS)

    Finch, W.I.

    1985-01-01

    The similarity of most of the deposits described in this report is striking even though they occur in sandstone host rocks ranging in age from Carboniferous to Tertiary and on every continent outside the polar regions. Geologic environments of the uranium deposits consist of distinctive sets of tectonic and sedimentary-depositional systems, all of which have some common threads of favorable geologic processes. In this summary paper it is hoped that this report has sharpened an understanding of the deposit's ''home environment'' that will aid future exploration for these resource-important sandstone-type uranium ores

  19. Elevated Uranium in Aquifers of the Jacobsville Sandstone

    Science.gov (United States)

    Sherman, H.; Gierke, J.

    2003-12-01

    The EPA has announced a new standard for uranium in drinking water of 30 parts per billion (ppb). This maximum contaminant level (MCL) takes effect for community water supplies December 2003. The EPA's ruling has heightened awareness among residential well owners that uranium in drinking water may increase the risk of kidney disease and cancer and has created a need for a quantified, scientific understanding of the occurrence and distribution of uranium isotopes in aquifers. The authors are investigating the occurrence of elevated uranium in northern Michigan aquifers of the Middle Proterozoic Jacobsville sandstone, a red to mottled sequence of sandstones, conglomerates, siltstones and shales deposited as basin fill in the 1.1 Ga Midcontinent rift. Approximately 25% of 300 well water samples tested for isotopic uranium have concentrations above the MCL. Elevated uranium occurrences are distributed throughout the Jacobsville sandstone aquifers stretching across Michigan's Upper Peninsula. However, there is significant variation in well water uranium concentrations (from 0.01 to 190 ppb) and neighboring wells do not necessarily have similar concentrations. The authors are investigating hydrogeologic controls on ground water uranium concentrations in the Jacobsville sandstone, e.g. variations in lithology, mineralogy, groundwater residence time and geochemistry. Approximately 2000' of Jacobsville core from the Amoco St. Amour well was examined in conjunction with the spectral gamma ray log run in the borehole. Spikes in equivalent uranium (eU) concentration from the log are frequently associated with clay and heavy mineral layers in the sandstone core. The lithology and mineralogy of these layers will be determined by analysis of thin sections and x-ray diffraction. A portable spectrometer, model GRS-2000/BL, will be used on the sandstone cliffs along Lake Superior to characterize depositional and lithologic facies of the Jacobsville sandstone in terms of

  20. Hydrogeology of the Potsdam Sandstone in northern New York

    Science.gov (United States)

    Williams, John H.; Reynolds, Richard J.; Franzi, David A.; Romanowicz, Edwin A.; Paillet, Frederick L.

    2010-01-01

    The Potsdam Sandstone of Cambrian age forms a transboundary aquifer that extends across northern New York and into southern Quebec. The Potsdam Sandstone is a gently dipping sequence of arkose, subarkose, and orthoquartzite that unconformably overlies Precambrian metamorphic bedrock. The Potsdam irregularly grades upward over a thickness of 450 m from a heterogeneous feldspathic and argillaceous rock to a homogeneous, quartz-rich and matrix-poor rock. The hydrogeological framework of the Potsdam Sandstone was investigated through an analysis of records from 1,500 wells and geophysical logs from 40 wells, and through compilation of GIS coverages of bedrock and surficial geology, examination of bedrock cores, and construction of hydrogeological sections. The upper several metres of the sandstone typically is weathered and fractured and, where saturated, readily transmits groundwater. Bedding-related fractures in the sandstone commonly form sub-horizontal flow zones of relatively high transmissivity. The vertical distribution of sub-horizontal flow zones is variable; spacings of less than 10 m are common. Transmissivity of individual flow zones may be more than 100 m2/d but typically is less than 10 m2/d. High angle fractures, including joints and faults, locally provide vertical hydraulic connection between flow zones. Hydraulic head gradients in the aquifer commonly are downward; a laterally extensive series of sub-horizontal flow zones serve as drains for the groundwater flow system. Vertical hydraulic head differences between shallow and deep flow zones range from 1 m to more than 20 m. The maximum head differences are in recharge areas upgradient from the area where the Chateauguay and Chazy Rivers, and their tributaries, have cut into till and bedrock. Till overlies the sandstone in much of the study area; its thickness is generally greatest in the western part, where it may exceed 50 m. A discontinuous belt of bedrock pavements stripped of glacial drift extends

  1. A new bee species that excavates sandstone nests.

    Science.gov (United States)

    Orr, Michael C; Griswold, Terry; Pitts, James P; Parker, Frank D

    2016-09-12

    Humanity has long been fascinated by animals with apparently unfavorable lifestyles [1]. Nesting habits are especially important because they can limit where organisms live, thereby driving population, community, and even ecosystem dynamics [2]. The question arises, then, why bees nest in active termite mounds [3] or on the rim of degassing volcanoes, seemingly preferring such hardship [4]. Here, we present a new bee species that excavates sandstone nests, Anthophora (Anthophoroides) pueblo Orr (described in Supplemental Information, published with this article online), despite the challenges already inherent to desert life. Ultimately, the benefits of nesting in sandstone appear to outweigh the associated costs in this system. Copyright © 2016 Elsevier Ltd. All rights reserved.

  2. Anatomy of anomalously thick sandstone units in the Brent Delta of the northern North Sea

    Science.gov (United States)

    Wei, Xiaojie; Steel, Ronald J.; Ravnås, Rodmar; Jiang, Zaixing; Olariu, Cornel; Ma, Yinsheng

    2018-05-01

    Some potentially attractive reservoirs, containing anomalously thick (10s to a few 100 m), cross-stratified sandstone, have been locally encountered within both the classic regressive (lower Brent) and the transgressive (upper Brent) segments of the Brent Delta. Three documented cases of these sandstone bodies are re-examined. They are internally dominated by simple or compound dunes, and typified by two types of deepening-upward succession, recording a retrogradational or transgressive shoreline history. Type I is expressed as a single estuarine succession changing upwards from erosive, coarse-grained channelized deposits into outer estuary tidal bar deposits. The estuary is underlain and overlain by deltaic deposits. Type II lacks significant basal river deposits but is composed by stacked mixed-energy and tide-dominated estuarine deposits. It is underlain by deltaic deposits and overlain by open marine sediments. Considering the structural evolution in the northern North Sea basin, we suggest (as did some earlier researchers) that these sandstone bodies were local, but sometimes broad transgressive estuaries, formed at any time during large-scale Brent Delta growth and decay. The estuary generation was likely triggered by fluvial incision coupled with active faulting, producing variable accommodation embayments, where tidal currents became focused and deposition became transgressive. The spatial variations of the interpreted estuary deposits were linked with variable, fault-generated accommodation. The relatively simple, lower Brent estuarine units were created by short-lived, fault activity in places, whereas the complex, stacked upper-Brent estuarine units were likely a result of more long-lived, punctuated fault-induced subsidence leading into the northern North Sea main rifting stage. The thick cross-stratified units potentially accumulated in the hangingwall of large bounding faults.

  3. Discussion on the origin of bleached sandstone of Qianjiadian uranium deposit

    International Nuclear Information System (INIS)

    Pang Yaqing; Xiang Weidong; Li Tiangang; Chen Xiaolin; Xia Yuliang

    2007-01-01

    Qianjiadian uranium deposit is a sandstone-type uranium deposit that has been discovered in Songliao Basin in recent years. Uranium ore bodies are planar or lenticular in shape and under the control of the contact between gray sandstones and bleached sandstones. The bleached sandstone is white in color, cemented loosely, nearly without TOC and pyrite contained and rich in uranium. Geochemical characteristics and types and assemblages of clay minerals of the bleached sandstone reveal that the bleached sandstone is the product of oxidation of the interlayer oxidation zone, and it is a part of the interlayer oxidation zone. The main reasons for white color of the bleached sandstone are transfer of iron ion, oxidation of TOC and kaolinization of sandstone. (authors)

  4. Petrographic study of core plugs from lower goru sandstones

    International Nuclear Information System (INIS)

    Memon, M.K.; Tunio, A.; Leghari, A.

    2008-01-01

    Petrographic rock type description is a fundamental component in the reservoir description processes and typically included measurement to identify sediment source, texture, composition and mineralogy. Petroleum workers have long used the Petrographic microscope as an in put device to aid in the study of pore systems. Standard Petrographic thin sections are typically 30 micrometers thick and are usually illuminated by transmitted light. Experienced examiners have trained themselves to see information such as pore size, mineralogy, compaction, etc by disregarding artifacts produced by passing light through a section. This method is adequate for qualitative interpretation of data from thin sections. Rocks in thin section under a microscope display great complexity in pore sizes and shapes. Petrographic study provides measurement on rock texture. Texture deals with the size, shape and arrangement of the component minerals of a rock. It is essentially the micro geometry of the rock. Permeability of collected core plugs of lower Goru sandstones was measured. From this Petrographic study we have identified as the sandstone of Lower Goru constitute almost entirely of quartz. The grains range in size from very fine to medium, moderately well sorted to well sorted and rounded to sub rounded in shape. Particularly attention was paid to mineral content present in Lower Goru Sandstone. The mineral composition from these core plugs of Lower Goru Sandstone as identified contain about 70-80% Quartz with traces of feldspar, muscovite, biotite, Epidote and hornblende. Calcite was present as cementing material and it was about 15 -30% of the total rock. (author)

  5. Provenance of sandstone on the western flank of Anambra Basin ...

    African Journals Online (AJOL)

    Petrographic and heavy mineral studies were carried out on clastic deposits that crop out in Ikpeshi, Auchi and Fugar localities in order to determine the provenance of the ... The heavy mineral suites and the petrographic signatures of the sandstones suggest derivation mainly from acid igneous rocks, gneisses and older ...

  6. A new bee species that excavates sandstone nests

    Science.gov (United States)

    Many wonder why animals act in seemingly injurious ways. Understanding the behavior of pollinators such as bees is especially important because of the necessary ecosystem service they provide. The new species Anthophora pueblo, discovered excavating sandstone nests, provides a model system for addre...

  7. Modal analysis and geochemistry of two sandstones of the Bhander ...

    Indian Academy of Sciences (India)

    and tectonic setting interpretations are based on modal analysis and whole rock geochemistry. The average ... that major part of the sediments were derived from the granitic source area. The sandstone ...... The geochemical gap shown by trace and rare ... of the Council of Scientific and Industrial Research,. New Delhi, in ...

  8. Effect of Crushed Sandstone Sand on the Properties of High ...

    African Journals Online (AJOL)

    This paper presents results of the laboratory investigation on high performance concrete (HPC) using crushed sandstone sand as 20%, 40%, and 60% replacement of river sand together with superplastisizer and silica fume (SF). The fresh concrete properties such as slump, air content and fresh concrete density have been ...

  9. The effect of hot water injection on sandstone permeability

    DEFF Research Database (Denmark)

    Rosenbrand, Esther; Haugwitz, Christian; Jacobsen, Peter Sally Munch

    2014-01-01

    Seasonal energy storage can be achieved by hot water injection in geothermal sandstone aquifers. We present an analysis of literature data in combination with new short-term flow through permeability experiments in order to address physical and physico-chemical mechanisms that can alter...

  10. Influence of fluvial sandstone architecture on geothermal energy production

    NARCIS (Netherlands)

    Willems, C.J.L.; Maghami Nick, Hamidreza M.; Weltje, G.J.; Donselaar, M.E.; Bruhn, D.F.

    2015-01-01

    Fluvial sandstone reservoirs composed of stacked meander belts are considered as potential geothermal resources in the Netherlands. Net-to-gross, orientation and stacking pattern of the channel belts is of major importance for the connectivity between the injection and production well in such

  11. Diagenesis, provenance and depositional environments of the Bunter Sandstone Formation

    DEFF Research Database (Denmark)

    Olivarius, Mette; Weibel, Rikke; Friis, Henrik

    The Bunter Sandstone Formation in the northern North German Basin has large geothermal potential with high porosity and permeability (generally >15% and >100 mD, respectively) and with pore fluid temperatures that are adequate for geothermal energy production (c. 55–60˚C). A combined investigation...

  12. A complex investigation of building sandstones from Saxony (Germany)

    International Nuclear Information System (INIS)

    Goetze, Jens; Siedel, Heiner

    2007-01-01

    The present paper provides a methodology for the investigation and characterization of building sandstones. This analytical scheme was designed for distinguishing mature arenites, which in general show very similar properties and are difficult to distinguish. This is shown for Cretaceous sandstones from various occurrences in Saxony (Germany), which have been used for centuries as building materials. The procedure is mainly based on the combination of macroscopic rock description, thin section polarizing microscopy (phase composition, texture, grain-size distribution) and cathodoluminescence (CL) microscopy (quartz types, feldspar and kaolinite content) coupled with image analysis, scanning electron microscopy (accessories, pore cement, diagenetic grain surface features), and analysis of pore space data. Sometimes, additional data from X-ray diffraction or chemical analyses (major and trace elements) can be used. Especially in the case of quartz rich arenites, CL is a powerful tool for provenance analysis. The detailed analysis of sandstone material in most cases allows us to assign historically used building material to a specific sandstone occurrence. These results are important for both interpreting the weathering behaviour of the building material and the conservation, reconstruction and stone replacement of historical monuments

  13. Aeromagnetic gradient survey used in sandstone type uranium deposits prospecting

    International Nuclear Information System (INIS)

    Li Xiaolu; Chang Shushuai

    2014-01-01

    The principle, advantage and data processing of aeromagnetic gradient survey approach is introduced in this paper which was used in sandstone type uranium deposits prospecting to study the shallow surface faults, uranium ore-forming environment and depth of magnetic body, which proved to be a good results. (authors)

  14. SmartPill® as an objective parameter for determination of severity and duration of postoperative ileus: study protocol of a prospective, two-arm, open-label trial (the PIDuSA study).

    Science.gov (United States)

    Vilz, Tim O; Pantelis, Dimitrios; Lingohr, Philipp; Fimmers, Rolf; Esmann, Anke; Randau, Thomas; Kalff, Jörg C; Coenen, Martin; Wehner, Sven

    2016-07-08

    Postoperative ileus (POI) is a frequent complication after abdominal surgery (AS). Until today, neither a prophylaxis nor an evidence-based therapy exists. This originates from the absence of objective parameters evaluating the severity and duration of POI resulting in clinical trials of modest quality. The SmartPill(®), a capsule which frequently measures pH value, temperature and intraluminal pressure after swallowing, offers an elegant option for analysing gastrointestinal (GI) transit times and smooth muscle activity in vivo. As the use in patients in the first months after AS is not covered by the marketing authorisation, we aim to investigate the safety and feasibility of the SmartPill(®) immediately after surgery. Additionally, we analyse the influence of prokinetics and laxatives as well as standardised physiotherapy on postoperative bowel contractility, as scientific evidence of its effects is still lacking. The PIDuSA study is a prospective, single-centre, two-arm, open-label trial. The SmartPill(®) will be applied to 55 patients undergoing AS having a high risk for POI and 10 patients undergoing extra-abdominal surgery rarely developing POI. The primary objective is the safety of the SmartPill(®) in patients after surgery on the basis of adverse device effects/serious adverse device effects (ADE/SADE). The sample size suggests that events with a probability of 3% could be seen with a certainty of 80% for at least once in the sample. Secondary objective is the analysis of postoperative intestinal activity in the GI tract in both groups. Furthermore, clinical signs of bowel motility disorders will be correlated to the data measured by the SmartPill(®) to evaluate its significance as an objective parameter for assessing POI severity. Additionally, effects of prokinetics, laxatives and physiotherapy on postoperative peristaltic activity recorded by the SmartPill(®) will be analysed. The protocol was approved by the federal authority (94

  15. Sandstone Relief Geohazards and their Mitigation: Rock Fall Risk Management in the Bohemian Switzerland National Park

    Czech Academy of Sciences Publication Activity Database

    Vařilová, Zuzana; Zvelebil, J.

    2005-01-01

    Roč. 44, - (2005), s. 53-58 ISSN 1682-5519. [Sandstone Landscapes in Europe. Past, Present and Future. International Conference on Sandstone Landscapes /2./. Vianden, 25.05.2005-28.05.2005] Keywords : sandstones * rock-slope instability * rock fall * risk evalution and mitigation * monitoring net * remedial works Subject RIV: DO - Wilderness Conservation

  16. Pulse duration discriminator

    International Nuclear Information System (INIS)

    Kosakovskij, L.F.

    1980-01-01

    Basic circuits of a discriminator for discrimination of pulses with the duration greater than the preset one, and of a multifunctional discriminator allowing to discriminate pulses with the duration greater (tsub(p)>tsub(s)) and lesser (tsub(p) tsub(s) and with the duration tsub(p) [ru

  17. Fast evolving conduits in clay-bonded sandstone: Characterization, erosion processes and significance for the origin of sandstone landforms

    Czech Academy of Sciences Publication Activity Database

    Bruthans, J.; Svetlik, D.; Soukup, J.; Schweigstillová, Jana; Válek, Jan; Sedláčková, M.; Mayo, A.L.

    2012-01-01

    Roč. 177, December (2012), s. 178-193 ISSN 0169-555X R&D Projects: GA AV ČR IAA300130806 Institutional support: RVO:67985891 ; RVO:68378297 Keywords : sandstone * erosion * piping * tensile strength * conduit * landform Subject RIV: DA - Hydrology ; Limnology Impact factor: 2.552, year: 2012

  18. Multidisciplinary studies on ancient sandstone quarries of Western Sardinia (Italy).

    Science.gov (United States)

    Grillo, Silvana Maria; Del Vais, Carla; Naitza, Stefano

    2013-04-01

    The ancient coastal quarries of Mediterranean are increasingly considered geosites of multidisciplinary relevance. They are sites of historical-archaeological interest that show ancient techniques of stone extraction; they are significant for cultural heritage conservation and restoration, as sources of the stones used in ancient buildings and monuments; they are sites of geological relevance, as often retain important stratigraphic sections; they are also useful markers of secular changes in the sea level. A multisciplinary study is in progress on the ancient quarries of the Sinis region (western Sardinia island), integrating archaeological, geological, minero-petrographical data. In Sardinia, coastal quarries have been established from Punic and Roman times. Many of them exploited Quaternary sediments along the southern and western coasts of the island. They consist of middle-late Pleistocene marine conglomerates and carbonate sandstones, and of coastal (aeolian) carbonate sandstones. Sandstone blocks of different sizes have been widely used in ancient cities for buildings, defensive works, harbours, etc. Three main areas of stone extraction (San Giovanni di Sinis, Punta Maimoni, Is Arutas) have been so far recognized in the Sinis. GIS-supported mapping and documentation of the sites includes their geology and stratigraphy, the extension and layout of the quarries, and an evaluation of volumes of extracted rocks. Documented archaeological evidences include ancient extraction fronts, spoil heaps, working areas, working traces in the old fronts, transport routes of blocks, and traces of loading facilities. The study is aimed at reconstructing the relationships of the quarries with the urban areas of Sinis, as the ancient Punic-Roman city of Tharros. Consequently, a minero-petrographical characterization (optical microscopy, XRD) is performed on sandstones sampled in each quarry, and in historical buildings in Tharros and other centres of the region (Cabras

  19. Distinguishing of uranium-bearing sandstone by the geochemical characteristics in northern Sichuan

    International Nuclear Information System (INIS)

    Wang Wangzhang; Zhang Zhufeng; Wang Yunliang; Sun Shuqin.

    1994-01-01

    Expounding geochemical characteristics of sandstone-type uranium deposits in northern Sichuan, the authors demonstrate the favourable and unfavourable conditions for enrichment of uranium on the basis of element abundances and ratios of U, Th and K measured by the gamma-ray spectroscopy surveying. The differences between uranium-bearing and non-uranium sandstones and between red sandstone (clay stone) and greenish sandstone can be determined by the gamma-ray spectroscopy (measuring U, Th and K) and XRF analysis (measuring As and Ba). Therefore, the prospecting of the sandstone-type uranium deposits in northern Sichuan can be concentrated in a certain range

  20. Topological representation of the porous structure and its evolution of reservoir sandstone under excavation-induced loads

    Directory of Open Access Journals (Sweden)

    Ju Yang

    2017-01-01

    Full Text Available The porous structure of a reservoir rock greatly influences its evolutive deformation and fracture behavior during excavation of natural resources reservoirs. Most numerical models for porous structures have been used to predict the quasi-static mechanical properties, but few are available to accurately characterize the evolution process of the porous structure and its influence on the macroscopic properties of reservoir rocks. This study reports a novel method to characterize the porous structure of sandstone using its topological parameters and to determine the laws that govern the evolutive deformation and failure of the topological structure under various uniaxial compressive loads. A numerical model of the porous sandstone was established based on the pore characteristics that were acquired using computed tomography imaging techniques. The analytical method that integrates the grassfire algorithm and the maximum inscribed sphere algorithm was proposed to create the 3-D topological model of the deformed porous structure, through which the topological parameters of the structure were measured and identified. The evolution processes of the porous structure under various loads were characterized using its equivalent topological model and parameters. This study opens a new way to characterize the dynamic evolution of the pore structure of reservoir sandstone under excavation disturbance.

  1. Integrated geomechanical, petrographical and petrophysical study of the sandstones of the Wajid Group, SW Saudi Arabia

    Science.gov (United States)

    Benaafi, Mohammed; Hariri, Mustafa; Al-Shaibani, Abdulaziz; Abdullatif, Osman; Makkawi, Mohammed

    2018-07-01

    The Cambro-Permian siliciclastic succession in southwestern Saudi Arabia is represented by the Wajid Group, which consists mainly of fluvial, shallow marine, aeolian, and glacial sandstones. The Wajid Group comprises the Dibsiyah, Sanamah, Qalibah, Khusayyayn, and Juwayl Formations. It is exposed in the Wadi Al-Dawasir area and extends to Najran City. The sandstones of the Wajid Group serve as groundwater aquifers in the Wadi Al-Dawasir and Najran areas and host hydrocarbon (mainly gas) reservoirs in the Rub' Al-Khali Basin. This study aims to characterize the geomechanical properties (rock strength and Young's modulus) of the sandstones of the Wajid Group using field and experimental techniques. A further objective is to investigate the relationships between the geomechanical properties and the petrographical and petrophysical properties of the studied sandstones. The geomechanical properties of the studied sandstones vary from glacial to non-glacial sandstones, as the glacial sandstones display high values of the geomechanical properties with high variability indices. Four geological factors including grain size, cement content, porosity and permeability were observed as the main controls on the geomechanical behaviour of the studied sandstones except for the Khusayyayn sandstone, where the mineral composition was also important. Significant correlations were observed between the petrographical and petrophysical properties and the geomechanical properties of the glacial sandstones. Predictive models of the geomechanical properties (RN, UCS, and E) were generated using regression analysis to account for the glacial sandstones.

  2. Sedimentary uranium occurrences in Eastern Europe with special reference to sandstone formations

    International Nuclear Information System (INIS)

    Barthel, F.; Hahn, L.

    1985-01-01

    Sedimentary uranium deposits, especially in sandstones, play an important role in uranium mining in Eastern Europe. The paper reviews recent publications on uranium occurrences in sandstone formations in the German Democratic Republic, Poland, CSSR, Hungary, Romania, Bulgaria and Albania. The uranium deposits in sandstones in Yugoslavia are described in a separate paper in this volume. Sandstone deposits of the USSR are not reviewed. Uranium mineralizations occur in sandstones from Ordovician to Tertiary age. Major deposits are developed in Upper Carboniferous sandstones in association with coal (GDR, Poland), in Permian strata (CSSR, Hungary, Romania), in Cretaceous sandstones (GDR, CSSR), and in Tertiary sediments (CSSR). The Permian deposits can be compared with deposits of similar age in Northern Italy and Northern Yugoslavia. Roll-type orebodies are developed in some of the Cenomanian sandstones. Tertiary deposits are mainly associated with lignites. Uranium deposits in sandstones of Albania and Bulgaria are not described in the literature. Geologic similarities with sandstone basins in adjacent countries suggest the presence of uranium mineralizations in Permian, Lower Triassic, and Tertiary sandstones. (author)

  3. Uranium distribution and sandstone depositional environments: oligocene and upper Cretaceous sediments, Cheyenne basin, Colorado

    International Nuclear Information System (INIS)

    Nibbelink, K.A.; Ethridge, F.G.

    1984-01-01

    Wyoming-type roll-front uranium deposits occur in the Upper Cretaceous Laramie and Fox Hills sandstones in the Cheyenne basin of northeastern Colorado. The location, geometry, and trend of specific depositional environments of the Oligocene White River and the Upper Cretaceous Laramie and Fox Hills formations are important factors that control the distribution of uranium in these sandstones. The Fox Hills Sandstone consists of up to 450 ft (140 m) of nearshore marine wave-dominated delta and barrier island-tidal channel sandstones which overlie offshore deposits of the Pierre Shale and which are overlain by delta-plain and fluvial deposits of the Laramie Formation. Uranium, which probably originated from volcanic ash in the White River Formation, was transported by groundwater through the fluvial-channel deposits of the White River into the sandstones of the Laramie and Fox Hills formations where it was precipitated. Two favorable depositional settings for uranium mineralization in the Fox Hills Sandstone are: (1) the landward side of barrier-island deposits where barrier sandstones thin and interfinger with back-barrier organic mudstones, and (2) the intersection of barrier-island and tidal channel sandstones. In both settings, sandstones were probably reduced during early burial by diagenesis of contained and adjacent organic matter. The change in permeability trends between the depositional strike-oriented barrier sandstones and the dip-oriented tidal-channel sandstones provided sites for dispersed groundwater flow and, as demonstrated in similar settings in other depositional systems, sites for uranium mineralization

  4. Distribution characteristics of Shihongtan uranium deposits calcareous sandstone and discussion on their genesis

    International Nuclear Information System (INIS)

    Zhu Huanqiao; Jia Heng; Xu Gaozhong; Li Zhanyou

    2007-12-01

    It is considered that the calcareous sandstone appear at layer along of a bunch of pear lens on and off, localled near up and down surface of sandbody or washed surface, has sandstone of more macro-grain and more gradation through statistics and analysis of calcareous sandstone in goal layer in Shihongtan uranium deposits. The calcareous sandstone accumulation thickness chorogram demonstrated that the calcareous sandstone centralized distribution in the ore body growth area, thus it can be seen, in the oxidation reduction intermediate belt the calcareous sandstone forms with the uranium mine has the certain origin relation. Choropleth map of summed thickness of calcareous sandstone deserves that it mainly appear in area of uranium body and related cause of formation of ore body of interlayer deacidizing--oxidation belt. (authors)

  5. Formation conditions and prospecting criteria for sandstone uranium deposit of interlayer oxidation type

    International Nuclear Information System (INIS)

    Huang Shijie

    1994-01-01

    This paper comprehensively analyses the geotectonic setting and favourable conditions, such as structure of the basin, sedimentary facies and paleogeography, geomorphology and climate, hydrodynamics and hydrogeochemistry, the development of interlayered oxidation etc, necessary for the formation of sandstone uranium deposit of interlayered oxidation type. The following prospecting criteria is proposed, namely: abundant uranium source, arid climate, stable big basin, flat-lying sandstone bed, big alluvial fan, little change in sedimentary facies, intercalation of sandstone and mudstone beds, shallow burying of sandstone bed, well-aquiferous sandstone bed, high permeability of sandstone bed, development of interlayered oxidation, and high content of reductant in sandstone. In addition, the 6 in 1 hydrogenic genetic model is proposed

  6. What classic greywacke (litharenite) can reveal about feldspar diagenesis: An example from Permian Rotliegend sandstone in Hessen, Germany

    Science.gov (United States)

    Molenaar, Nicolaas; Felder, Marita; Bär, Kristian; Götz, Annette E.

    2015-08-01

    Rotliegend siliciclastic sediments in southern Hessen (Germany) are a good example of dissolution of detrital feldspars, which is a common feature in many sandstones. Dissolution occurred after mechanical compaction of the lithic-rich sandstone, which experienced framework collapse with pores and pore connections filled and obstructed by deformed ductile lithic grains (pseudomatrix) thereby reducing pore space to microporosity., The advanced degree of compaction and reduced porosity caused low permeability and low hydraulic conductivity of the rock mass. This is further reduced by the presence of wackes and shales that occur intercalated with the sandstones. Feldspar dissolution thus took place in low permeable sediments when large-scale flow of meteoric or acidic fluids is ruled out as a cause of feldspar dissolution. Mineral precipitation (illite, kaolinite, and albite) took place within pseudomatrix and detrital matrix as well as in secondary pores created by feldspar dissolution. Feldspar was the source for the authigenesis. The system was thus closed during burial after framework collapse, and diagenetic reactants in the form of detrital components were already present within the system. The original mass was preserved, but redistributed and diagenetic minerals were the local sinks for the dissolved reactants, precipitating within the system. This also suggests that burial diagenesis in general might be more mass conservative than usually assumed. Rotliegend sandstones thus form a case where, despite of the lack of external exchange of mass by fluid flow, major diagenetic processes did take place and significantly modified the original mineralogy and texture. Feldspar diagenesis can take place from other processes than mere large-scale flushing of open systems as often supposed. It implies that the volumes of rock affected by feldspar diagenesis may be much larger than anticipated based upon the common hold believe that feldspar diagenesis is linked to

  7. Effect Of Hot Water Injection On Sandstone Permeability

    DEFF Research Database (Denmark)

    Rosenbrand, Esther; Fabricius, Ida Lykke

    2012-01-01

    of published results regarding the effect of temperature on sandstone permeability. These tests are performed with mineral oil, nitrogen gas, distilled water and solutions of NaCl, KCl, CaCl2 as well as brines that contain a mixture of salts. Thirteen sandstone formations, ranging from quartz arenites...... to formations with a significant fraction of fine particles including clay minerals are investigated. The porosities range from 0.10 to 0.30 and permeabilities span the range from 1 to 1000 md. To compare different rock types, specific surface is determined from permeability and porosity using Kozeny’s equation...... not account for all the permeability reductions observed. Permeablity reduction occurs both when distilled water is the saturating fluid as well as in tests with NaCl, KCl or CaCl2 solutions, however, this is not the case in tests with mineral oil or nitrogen gas. The formation of a filter cake or influx...

  8. Discounted Duration Calculus

    DEFF Research Database (Denmark)

    Ody, Heinrich; Fränzle, Martin; Hansen, Michael Reichhardt

    2016-01-01

    To formally reason about the temporal quality of systems discounting was introduced to CTL and LTL. However, these logic are discrete and they cannot express duration properties. In this work we introduce discounting for a variant of Duration Calculus. We prove decidability of model checking...... for a useful fragment of discounted Duration Calculus formulas on timed automata under mild assumptions. Further, we provide an extensive example to show the usefulness of the fragment....

  9. Strength curves for shales and sandstones under hydrostatic confining pressures

    International Nuclear Information System (INIS)

    Gupta, S.C.; Sikka, S.K.

    1978-01-01

    The experimental data for the effect of confining pressures on the fracture stress have been analysed for shales and sandstones. The normalized compressive strengths are found to lie in a narrow region so that Ohnaka's equation for crystalline rocks, can be fitted to the data. The fitted parameters are physically reasonable and indicate that the functional dependence of strength on porosity, strain rate and temperature is independent of the confining pressures. (author)

  10. New Acid Combination for a Successful Sandstone Acidizing

    Science.gov (United States)

    Shafiq, M. U.; Mahmud, H. K. B.; Rezaee, R.

    2017-05-01

    With the development of new enhanced oil recovery techniques, sandstone acidizing has been introduced and played a pivotal role in the petroleum industry. Different acid combinations have been applied, which react with the formation, dissolve the soluble particles; thus increase the production of hydrocarbons. To solve the problems which occurred using current preflush sandstone acidizing technology (hydrochloric acid); a new acid combination has been developed. Core flooding experiments on sandstone core samples with dimensions 1.5 in. × 3 in. were conducted at a flow rate of 2 cm3/min. A series of hydrochloric-acetic acid mixtures with different ratios were tested under 150°F temperature. The core flooding experiments performed are aimed to dissolve carbonate, sodium, potassium and calcium particles from the core samples. These experiments are followed by few important tests which include, porosity-permeability, pH value, Inductively Coupled Plasma (ICP) analysis and Nuclear Magnetic Resonance (NMR measurements). All the results are compared with the results of conventional hydrochloric acid technology. NMR and porosity analysis concluded that the new acid combination is more effective in creating fresh pore spaces and thus increasing the reservoir permeability. It can be seen from the pore distribution before and after the acidizing. Prior applying acid; the large size of pores appears most frequently in the pore distribution while with the applied acid, it was found that the small pore size is most the predominant of the pore distribution. These results are validated using ICP analysis which shows the effective removal of calcium and other positive ions from the core sample. This study concludes that the combination of acetic-hydrochloric acid can be a potential candidate for the preflush stage of sandstone acidizing at high temperature reservoirs.

  11. Controls on the variability of net infiltration to desert sandstone

    Science.gov (United States)

    Heilweil, Victor M.; McKinney, Tim S.; Zhdanov, Michael S.; Watt, Dennis E.

    2007-01-01

    As populations grow in arid climates and desert bedrock aquifers are increasingly targeted for future development, understanding and quantifying the spatial variability of net infiltration becomes critically important for accurately inventorying water resources and mapping contamination vulnerability. This paper presents a conceptual model of net infiltration to desert sandstone and then develops an empirical equation for its spatial quantification at the watershed scale using linear least squares inversion methods for evaluating controlling parameters (independent variables) based on estimated net infiltration rates (dependent variables). Net infiltration rates used for this regression analysis were calculated from environmental tracers in boreholes and more than 3000 linear meters of vadose zone excavations in an upland basin in southwestern Utah underlain by Navajo sandstone. Soil coarseness, distance to upgradient outcrop, and topographic slope were shown to be the primary physical parameters controlling the spatial variability of net infiltration. Although the method should be transferable to other desert sandstone settings for determining the relative spatial distribution of net infiltration, further study is needed to evaluate the effects of other potential parameters such as slope aspect, outcrop parameters, and climate on absolute net infiltration rates.

  12. Lattice strain measurements on sandstones under load using neutron diffraction

    Science.gov (United States)

    Frischbutter, A.; Neov, D.; Scheffzük, Ch.; Vrána, M.; Walther, K.

    2000-11-01

    Neutron diffraction methods (both time-of-flight- and angle-dispersive diffraction) are applied to intracrystalline strain measurements on geological samples undergoing uniaxial increasing compressional load. The experiments were carried out on Cretaceous sandstones from the Elbezone (East Germany), consisting of >95% quartz which are bedded but without crystallographic preferred orientation of quartz. From the stress-strain relation the Young's modulus for our quartz sample was determined to be (72.2±2.9) GPa using results of the neutron time-of-flight method. The influence of different kinds of bedding in sandstones (laminated and convolute bedding) could be determined. We observed differences of factor 2 (convolute bedding) and 3 (laminated bedding) for the elastic stiffness, determined with angle dispersive neutron diffraction (crystallographic strain) and with strain gauges (mechanical strain). The data indicate which geological conditions may influence the stress-strain behaviour of geological materials. The influence of bedding on the stress-strain behaviour of a laminated bedded sandstone was indicated by direct residual stress measurements using neutron time-of-flight diffraction. The measurements were carried out six days after unloading the sample. Residual strain was measured for three positions from the centre to the periphery and within two radial directions of the cylinder. We observed that residual strain changes from extension to compression in a different manner for two perpendicular directions of the bedding plane.

  13. On the water saturation calculation in hydrocarbon sandstone reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Stalheim, Stein Ottar

    2002-07-01

    The main goal of this work was to identify the most important uncertainty sources in water saturation calculation and examine the possibility for developing new S{sub w} - equations or possibility to develop methods to remove weaknesses and uncertainties in existing S{sub w} - equations. Due to the need for industrial applicability of the equations we aimed for results with the following properties: The accuracy in S{sub w} should increase compared with existing S{sub w} - equations. The equations should be simple to use in petrophysical evaluations. The equations should be based on conventional logs and use as few as possible input parameters. The equations should be numerical stable. This thesis includes an uncertainty and sensitivity analysis of the most common S{sub w} equations. The results are addressed in chapter 3 and were intended to find the most important uncertainty sources in water saturation calculation. To increase the knowledge of the relationship between R{sub t} and S{sub w} in hydrocarbon sandstone reservoirs and to understand how the pore geometry affects the conductivity (n and m) of the rock a theoretical study was done. It was also an aim to examine the possibility for developing new S{sub w} - equations (or investigation an effective medium model) valid inhydrocarbon sandstone reservoirs. The results are presented in paper 1. A new equation for water saturation calculation in clean sandstone oil reservoirs is addressed in paper 2. A recommendation for best practice of water saturation calculation in non water wet formation is addressed in paper 3. Finally a new equation for water saturation calculation in thinly interbedded sandstone/mudstone reservoirs is presented in paper 4. The papers are titled: 1) Is the saturation exponent n a constant. 2) A New Model for Calculating Water Saturation In 3) Influence of wettability on water saturation modeling. 4) Water Saturation Calculations in Thinly Interbedded Sandstone/mudstone Reservoirs. A

  14. Experimental deformation in sandstone, carbonates and quartz aggregate

    Energy Technology Data Exchange (ETDEWEB)

    Cheung, Cecilia See Nga [Stony Brook Univ., NY (United States)

    2015-05-01

    The first part of my thesis is mainly focused on the effect of grain size distribution on compaction localization in porous sandstone. To identify the microstructural parameters that influence compaction band formation, I conducted a systematic study of mechanical deformation, failure mode and microstructural evolution in Bleurswiller and Boise sandstones, of similar porosity (~25%) and mineralogy but different sorting. Discrete compaction bands were observed to develop over a wide range of pressure in the Bleurswiller sandstone that has a relatively uniform grain size distribution. In contrast, compaction localization was not observed in the poorly sorted Boise sandstone. My results demonstrate that grain size distribution exerts important influence on compaction band development, in agreement with recently published data from Valley of Fire and Buckskin Gulch, as well as numerical studies. The second part aimed to improve current knowledge on inelastic behavior, failure mode and brittle-ductile transition in another sedimentary rock, porous carbonates. A micritic Tavel (porosity of ~13%) and an allochemical Indiana (~18%) limestones were deformed under compaction in wet and dry conditions. At lower confining pressures, shear localization occurred in brittle faulting regime. Through transitional regime, the deformation switched to cataclastic flow regime at higher confining pressure. Specifically in the cataclastic regime, the (dry and wet) Tavel and dry Indiana failed by distributed cataclastic flow, while in contrast, wet Indiana failed as compaction localization. My results demonstrate that different failure modes and mechanical behaviors under different deformation regimes and water saturation are fundamental prior to any geophysical application in porous carbonates. The third part aimed to focus on investigating compaction on quartz aggregate starting at low (MPa) using X-ray diffraction. We report the diffraction peak evolution of quartz with increasing

  15. Properties and durability assessment of glauconitic sandstone: A case study on Zamel sandstone from Bohemian Cretaceous Basin (Czech Republic)

    Czech Academy of Sciences Publication Activity Database

    Martinec, Petr; Vavro, M.; Ščučka, Jiří; Mašláň, M.

    2010-01-01

    Roč. 115, 3/4 (2010), s. 175-181 ISSN 0013-7952 R&D Projects: GA ČR GP101/07/P512; GA ČR(CZ) GA103/07/1662 Institutional research plan: CEZ:AV0Z30860518 Keywords : building stone * sandstone * physical properties Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.442, year: 2010 http://www.sciencedirect.com/science

  16. SmartPill? as an objective parameter for determination of severity and duration of postoperative ileus: study protocol of a prospective, two-arm, open-label trial (the PIDuSA study)

    OpenAIRE

    Vilz, Tim O; Pantelis, Dimitrios; Lingohr, Philipp; Fimmers, Rolf; Esmann, Anke; Randau, Thomas; Kalff, J?rg C; Coenen, Martin; Wehner, Sven

    2016-01-01

    Introduction Postoperative ileus (POI) is a frequent complication after abdominal surgery (AS). Until today, neither a prophylaxis nor an evidence-based therapy exists. This originates from the absence of objective parameters evaluating the severity and duration of POI resulting in clinical trials of modest quality. The SmartPill?, a capsule which frequently measures pH value, temperature and intraluminal pressure after swallowing, offers an elegant option for analysing gastrointestinal (GI) ...

  17. Microfracture spacing distributions and the evolution of fracture patterns in sandstones

    Science.gov (United States)

    Hooker, J. N.; Laubach, S. E.; Marrett, R.

    2018-03-01

    Natural fracture patterns in sandstone were sampled using scanning electron microscope-based cathodoluminescence (SEM-CL) imaging. All fractures are opening-mode and are fully or partially sealed by quartz cement. Most sampled fractures are too small to be height-restricted by sedimentary layers. At very low strains ( 100) datasets show spacings that are best fit by log-normal size distributions, compared to exponential, power law, or normal distributions. The clustering of fractures suggests that the locations of natural factures are not determined by a random process. To investigate natural fracture localization, we reconstructed the opening history of a cluster of fractures within the Huizachal Group in northeastern Mexico, using fluid inclusions from synkinematic cements and thermal-history constraints. The largest fracture, which is the only fracture in the cluster visible to the naked eye, among 101 present, opened relatively late in the sequence. This result suggests that the growth of sets of fractures is a self-organized process, in which small, initially isolated fractures grow and progressively interact, with preferential growth of a subset of fractures developing at the expense of growth of the rest. Size-dependent sealing of fractures within sets suggests that synkinematic cementation may contribute to fracture clustering.

  18. EFFECT OF SANDSTONE ANISOTROPY ON ITS HEAT AND MOISTURE TRANSPORT PROPERTIES

    Directory of Open Access Journals (Sweden)

    Jan Fořt

    2015-09-01

    Full Text Available Each type of natural stone has its own geological history, formation conditions, different chemical and mineralogical composition, which influence its possible anisotropy. Knowledge in the natural stones anisotropy represents crucial information for the process of stone quarrying, its correct usage and arrangement in building applications. Because of anisotropy, many natural stones exhibit different heat and moisture transport properties in various directions. The main goal of this study is to analyse several anisotropy indices and their effect on heat transport and capillary absorption. For the experimental determination of the anisotropy effect, five types of sandstone coming from different operating quarries in the Czech Republic are chosen. These materials are often used for restoration of culture heritage monuments as well as for other building applications where they are used as facing slabs, facade panels, decoration stones, paving, etc. For basic characterization of studied materials, determination of their bulk density, matrix density and total open porosity is done. Chemical composition of particular sandstones is analysed by X-Ray Fluorescence. Anisotropy is examined by the non-destructive measurement of velocity of ultrasonic wave propagation. On the basis of ultrasound testing data, the relative anisotropy, total anisotropy and anisotropy coefficient are calculated. Then, the measurement of thermal conductivity and thermal diffusivity in various directions of samples orientation is carried out. The obtained results reveal significant differences between the parameters characterizing the heat transport in various directions, whereas these values are in accordance with the indices of anisotropy. Capillary water transport is described by water absorption coefficient measured using a sorption experiment, which is performed for distilled water and 1M NaCl water solution.  The measured data confirm the effect of anisotropy which is

  19. Discussion on distribution characteristics of calcareous sandstone in Shihongtan uranium deposit and its genesis

    International Nuclear Information System (INIS)

    Zhu Huanqiao; Qiao Haiming; Jia Heng; Xu Gaozhong

    2007-01-01

    Based on the observation and statistics on the calcareous sandstone in the ore host layer in Shihongtan uranium deposit, this paper finds that the calcareous sandstone occurs on and off near the top or wash surface of the sandbody as beads-strings lens along the layer and concentrates in the area where the ore bodies are rich. In lithology, the calcareous sandstone is of coarse grain and fairly well sorted. According to the analysis on the lithogeochemical features and the carbon and oxygen isotopes of calcareous sandstones, it is realized that there some genetic relation between the formation of calcareous sandstone and uranium mineralization in the oxidation-deoxidation transitional belt, that is the precipitation and enrichment of uranium is accompanied by the deposition of carbonate and formation of calcareous sandstone. (authors)

  20. Cense Explosion Test Program. Report 1. Cense 1. Explosions in Sandstone

    Science.gov (United States)

    1977-09-01

    series, "Analysis and Summary of CENSE Data." 10 * _ CHAPTER 2 APPROACH 2.1 DESCRIPTION OF TEST SITE An exposed outcrop of Kayenta sandstone with 180...ft/s seismic velocity previously determined (References 12-14) for the unweathered upper zone of the Kayenta sandstone. 16 I The P-wave propagation...Propagation along the horizontal radial was 8400 ft/s. The seismic velocity pre- viously determined for Kayenta sandstone in this area was 7500 ft/s

  1. The Paleozoic-Mesozoic recycling of the Rakaia Terrane, South Island, New Zealand : sandstone clast and sandstone petrology, geochemistry, and geochronology

    International Nuclear Information System (INIS)

    Wandres, A.M.; Bradshaw, J.D.; Ireland, T.

    2005-01-01

    The Torlesse terranes - part of the New Zealand Eastern Province - are accretionary complexes that comprise an enormous volume of quartzofeldspathic sandstones and mudstones with subsidiary conglomerates plus minor oceanic assemblages. Two terranes are recognised in the South Island - the Permian to Late Triassic Rakaia Terrane and the Late Jurassic to Early Cretaceous Pahau Terrane. Sandstone clasts from two Rakaia Terrane and two Pahau Terrane conglomerates were collected. We present the first combined detailed information on petrography and geochemistry of Torlesse conglomerate sandstone clasts and use our own and published U-Pb SHRIMP detrital zircon age data to demonstrate the recycling of the Rakaia Terrane into Rakaia strata itself and into Pahau Terrane strata. Sandstone clast major and trace element chemical data largely support petrographic observations derived from thin-section analysis. The similarities of petrographic and geochemical data between sandstone clasts from the Rakaia Terrane and Rakaia sandstones suggest that clasts in the Permian Te Moana and Late Triassic Lake Hill Conglomerates were derived by autocannibalistic reworking of older, consolidated, Rakaia sediments. Data from sandstone clasts from the Pahau Terrane suggest that uplift of the Rakaia Terrane continued into the Cretaceous. These Pahau Terrane clasts indicate that at the time of the Pahau sedimentation Permian to early Late Triassic Rakaia rocks were exposed and recycled into the Pahau Basin. (author). 57 refs., 8 figs., 3 tables

  2. Trilobites from the Middle Ordovician Stairway Sandstone, Amadeus Basin, central Australia

    DEFF Research Database (Denmark)

    Jakobsen, Kristian Grube; Nielsen, Arne Thorshøj; Harper, David Alexander Taylor

    2014-01-01

    During the Middle Ordovician (Darriwilian) sandstones and siltstones were deposited in the epicontinental Larapintine Sea, which covered large parts of central Australia. The Darriwilian Stairway Sandstone has, for the first time, been sampled stratigraphically for macrofossils to track marine...... benthic biodiversity in this clastic-dominated shallow-water palaeoenvironment situated along the margin of northeastern Gondwana. The faunas from the Stairway Sandstone are generally of low diversity and dominated by bivalves but include several animal groups, with trilobites representing 25......% of the entire shelly fauna. Thirteen trilobite taxa are described from the Stairway Sandstone; the fauna displays a high degree of endemism. One new species, Basilicus (Parabasilicus) brumbyensis sp. nov. is described....

  3. Study of petrological characteristics of uranium-bearing sandstone in the south of ordos basin, China

    International Nuclear Information System (INIS)

    Tian Cheng; Jia Licheng; Li Song; Zhang Zimin

    2007-01-01

    This paper discusses the relation between uranium-bearing abundance and texture constituent of sedimentary rock, on the basis of the research of petrological characteristic of sandstone in the south of Ordos basin. The influence of infiltration of sandstone and uranium migration and accumulation by the major diagenesis of compaction and cementation, clay minerals evolution, corrosion and forming of secondary porosity are discussed. Uranium-bearing sandstones are divided into four types and their petrological characteristics are discussed. After mineralization conditions being summed up, the uranium-mineralization model of sandstone-type is built. Reliable petrological evidences for evaluating favourable uranium mineralization rich areas are furnished. (authors)

  4. Water Vapor Diffusion and Adsorption of Sandstones: Influence of Rock Texture and Composition

    Directory of Open Access Journals (Sweden)

    Martin Keppert

    2016-01-01

    Full Text Available The term sandstone is used for wide range of rocks containing quartz clasts which can be cemented by secondary precipitated quartz or calcite; moreover the space between clasts can be filled by matrix. These facts result in existence of numerous rocks having highly various properties. Sandstones have been used as construction materials due to their good accessibility and workability. Since most of sandstones are porous, water vapor can penetrate through sandstone constructions. The rate of water vapor diffusion, as well as the vapor sorption isotherm, was determined for range of sandstone types. The diffusion resistance factor was found to be dependent on the total porosity of sandstone but the sorption behavior was strongly influenced by nature of the particular sandstone; the specific surface area of stone and presence of clay matrix are determining its sorption isotherm. The published data enable estimating (i diffusion resistance factor of a sandstone via knowledge of its total porosity and (ii the sorption isotherm via knowledge of the stone’s nature and specific surface area. This approach can significantly reduce the time necessary to acquire vapor-related properties of a sandstone.

  5. Greybull Sandstone Petroleum Potential on the Crow Indian Reservation, South-Central Montana

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, David A.

    2002-05-13

    The focus of this project was to explore for stratigraphic traps that may be present in valley-fill sandstone at the top of the Lower Cretaceous Kootenai Formation. This sandstone interval, generally known as the Greybull Sandstone, has been identified along the western edge of the reservation and is a known oil and gas reservoir in the surrounding region. The Greybull Sandstone was chosen as the focus of this research because it is an excellent, well-documented, productive reservoir in adjacent areas, such as Elk Basin; Mosser Dome field, a few miles northwest of the reservation; and several other oil and gas fields in the northern portion of the Bighorn Basin.

  6. Simulation of channel sandstone architecture in an incised valley

    Energy Technology Data Exchange (ETDEWEB)

    Frykman, P.; Johannessen, P.; Andsbjerg, J.

    1998-12-31

    The present report describes a geostatistical modelling study that is aimed at reflecting the architecture of the channel sandstones in an incised valley fill. The example used for this study is a part of the Middle Jurassic sandy succession of the Bryne Formation in the Danish central Graben. The succession consists mainly of fluvial sediments in the lower part, overlain by tidal influenced sediments, which again is overlain by shallow marine sediments. The modelling study has been performed on a sequence of incised valley sediments in the upper part of the Bryne Formation overlying fluvial sediments. (au) EFP-96. 19 refs.

  7. Reservoir characterization of Pennsylvanian sandstone reservoirs. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kelkar, M.

    1995-02-01

    This final report summarizes the progress during the three years of a project on Reservoir Characterization of Pennsylvanian Sandstone Reservoirs. The report is divided into three sections: (i) reservoir description; (ii) scale-up procedures; (iii) outcrop investigation. The first section describes the methods by which a reservoir can be described in three dimensions. The next step in reservoir description is to scale up reservoir properties for flow simulation. The second section addresses the issue of scale-up of reservoir properties once the spatial descriptions of properties are created. The last section describes the investigation of an outcrop.

  8. Thermal study of sandstones from different Czech localities

    Czech Academy of Sciences Publication Activity Database

    Plevová, Eva; Vaculíková, Lenka; Kožušníková, Alena; Daněk, T.; Ritz, M.; Simha Martynková, G.

    2011-01-01

    Roč. 103, č. 3 (2011), s. 835-843 ISSN 1388-6150 R&D Projects: GA ČR GA105/08/1398; GA ČR GP105/07/P416 Grant - others:GA ČR(CZ) GP105/09/397 Institutional research plan: CEZ:AV0Z30860518 Keywords : thermomechanical and differential thermal analysis * optical microscopy * sandstones Subject RIV: CA - Inorganic Chemistry Impact factor: 1.604, year: 2011 http://www.springerlink.com/content/71n5427j2707g331/

  9. Modelling of a diffusion-sorption experiment on sandstone

    International Nuclear Information System (INIS)

    Smith, P.A.

    1989-11-01

    The results of a diffusion-sorption experiment on a sample of Darley Dale sandstone, using simulated groundwater spiked with a mixture of 125 I, 85 Sr and 137 Cs, are modelled by a one-dimensional porous medium approach in which sorption is described by Freundlich isotherms. The governing equations are solved analytically for the special case of a linear isotherm, and numerically using the computer code RANCHDIFF for non-linear isotherms. A set of time-dependent, ordinary differential equations is obtained using the Lagrange interpolation technique and integrated by Gear's variable order predictor-corrector method. It is shown that the sorption behaviour of 85 Sr can be modelled successfully by a linear isotherm, using a sorption parameter consistent with batch-sorption tests. The behaviour of 137 Cs may be modelled by a non-linear isotherm, but the amount of 137 Cs sorbed is less than that anticipated from batch-sorption tests. 125 I is assumed to be non-sorbing and is used to determine the porosity of the sandstone. (author) 10 figs., 4 tabs., 6 refs

  10. Comparison of Buffer Effect of Different Acids During Sandstone Acidizing

    International Nuclear Information System (INIS)

    Shafiq, Mian Umer; Mahmud, Hisham Khaled Ben; Hamid, Mohamed Ali

    2015-01-01

    The most important concern of sandstone matrix acidizing is to increase the formation permeability by removing the silica particles. To accomplish this, the mud acid (HF: HCl) has been utilized successfully for many years to stimulate the sandstone formations, but still it has many complexities. This paper presents the results of laboratory investigations of different acid combinations (HF: HCl, HF: H 3 PO 4 and HF: HCOOH). Hydrofluoric acid and fluoboric acid are used to dissolve clays and feldspar. Phosphoric and formic acids are added as a buffer to maintain the pH of the solution; also it allows the maximum penetration of acid into the core sample. Different tests have been performed on the core samples before and after the acidizing to do the comparative study on the buffer effect of these acids. The analysis consists of permeability, porosity, color change and pH value tests. There is more increase in permeability and porosity while less change in pH when phosphoric and formic acids were used compared to mud acid. From these results it has been found that the buffer effect of phosphoric acid and formic acid is better than hydrochloric acid. (paper)

  11. Selected trace and minor elements in sandstones from Paraguay

    International Nuclear Information System (INIS)

    Facetti-Masulli, J.F.; Gonzalez, E.; Kump, P.

    2010-01-01

    Selected trace and minor elements analyzed by XRF in sandstone samples were Rb-Sr-Zr-Nb-Ba-La-Ce-Nd as well as Ti-Mn-Fe with which they are often correlated. Refractory elements like REE are considered useful indicators of geochemical processes and, in this case, of provenance. Usually they maintain their original relationships and are transferred almost directly into sediments. The values here found, absolute and normalized, show correlations among the samples, allowing the establishment of their origin. Most of them in the spidergram patterns display positive spikes of Zr, and negative anomalies at Nb, Sr, Ti: differences in their height/depth could be in relation with the different Series or Formations. Strikingly, spidergrams of samples collected from the Patino Formation show marked negative anomalies interalia of Ba, as well as positive spikes of Nb and Zr, very similar to those found in magmatic specimens from Misiones, Carapegua-Acahay and Alto Paraguay Province and quite different from the other analyzed samples. In addition a remarkable presence of Precambrian signatures were found in the analyzed sandstones from the Paleozoic. (orig.)

  12. Selected trace and minor elements in sandstones from Paraguay

    Energy Technology Data Exchange (ETDEWEB)

    Facetti-Masulli, J.F.; Gonzalez, E. [Hydroconsult SRL, Asuncion (Paraguay); Kump, P. [J. Stefan Inst., Ljubljana (Slovenia)

    2010-07-01

    Selected trace and minor elements analyzed by XRF in sandstone samples were Rb-Sr-Zr-Nb-Ba-La-Ce-Nd as well as Ti-Mn-Fe with which they are often correlated. Refractory elements like REE are considered useful indicators of geochemical processes and, in this case, of provenance. Usually they maintain their original relationships and are transferred almost directly into sediments. The values here found, absolute and normalized, show correlations among the samples, allowing the establishment of their origin. Most of them in the spidergram patterns display positive spikes of Zr, and negative anomalies at Nb, Sr, Ti: differences in their height/depth could be in relation with the different Series or Formations. Strikingly, spidergrams of samples collected from the Patino Formation show marked negative anomalies interalia of Ba, as well as positive spikes of Nb and Zr, very similar to those found in magmatic specimens from Misiones, Carapegua-Acahay and Alto Paraguay Province and quite different from the other analyzed samples. In addition a remarkable presence of Precambrian signatures were found in the analyzed sandstones from the Paleozoic. (orig.)

  13. Clay minerals in sandstone uranium deposits: radwaste applications

    International Nuclear Information System (INIS)

    Brookins, D.G.

    1990-01-01

    Clay minerals play an important role in the genesis of uranium deposits in sandstones. They incorporate the rate earths (REE), U, Sb, Th, Cs, Rb, Sr, Y, Ba, and even small amounts of chalcophiles. These minerals possess analog elements for many of the radwaste fission products as well as actinides and some actinide daughters. In sandstone uranium deposits, clay minerals are also associated with sulfide minerals, usually pyrite, and organic carbonaceous matter. The primary clay minerals are usually smectites, illites, chlorites and mixed layer varieties. The integrity of these clay minerals is demonstrated by their retention of formational-mineralization ages determined by Rb-Sr geochronologic investigation of the Grants Mineral Belt of the United States. The importance of the clay minerals as analog for parts of the multi-barrier concept in radwaste disposal is their ability to impede water penetration into - and movement of key elements out of uranium rich zones. The clay minerals further sorb and in other ways incorporate into their structures many fission products and actinide analogs from man-made nuclear wastes. 22 refs., 1 fig., 3 tabs

  14. Measuring the zeta potential. The relationships with sandstone fineness

    Directory of Open Access Journals (Sweden)

    de Luxán, M. P.

    1989-09-01

    Full Text Available The application of the zeta potential technique in the area of construction materials and Portland cement is quite recent. The initial research work involved the study of cement suspensions or suspensions of one of the components of cement, such as alite, tricalcium alumínate, in the presence of additives and, more specifically, superplasticizers. The studies of this sort were extended with the mixing of active additions into cement (fly ashes, etc.. The present study discusses the application of siliceous materials (sandstone as a basis of the research into the behaviour of sandstone mortars containing repair products.

    La aplicación de la técnica del potencial zeta en el campo de los materiales de construcción y del cemento portland es muy reciente. Las primeras investigaciones se refieren al estudio de suspensiones de cemento o de alguno de sus compuestos que lo forman como alita, aluminato tricálcico, en presencia de aditivos y, más concretamente, de superfluidificantes. Con la incorporación de adiciones activas al cemento (cenizas volantes,... se amplían los estudios de este tipo de cementos. En este trabajo se considera la aplicación a los materiales silíceos (arenisca como base para la investigación del comportamiento de los morteros de arenisca conteniendo productos de reparación.

  15. Pore network properties of sandstones in a fault damage zone

    Science.gov (United States)

    Bossennec, Claire; Géraud, Yves; Moretti, Isabelle; Mattioni, Luca; Stemmelen, Didier

    2018-05-01

    The understanding of fluid flow in faulted sandstones is based on a wide range of techniques. These depend on the multi-method determination of petrological and structural features, porous network properties and both spatial and temporal variations and interactions of these features. The question of the multi-parameter analysis on fluid flow controlling properties is addressed for an outcrop damage zone in the hanging wall of a normal fault zone on the western border of the Upper Rhine Graben, affecting the Buntsandstein Group (Early Triassic). Diagenetic processes may alter the original pore type and geometry in fractured and faulted sandstones. Therefore, these may control the ultimate porosity and permeability of the damage zone. The classical model of evolution of hydraulic properties with distance from the major fault core is nuanced here. The hydraulic behavior of the rock media is better described by a pluri-scale model including: 1) The grain scale, where the hydraulic properties are controlled by sedimentary features, the distance from the fracture, and the impact of diagenetic processes. These result in the ultimate porous network characteristics observed. 2) A larger scale, where the structural position and characteristics (density, connectivity) of the fracture corridors are strongly correlated with both geo-mechanical and hydraulic properties within the damage zone.

  16. Sandstone-body and shale-body dimensions in a braided fluvial system: Salt wash sandstone member (Morrison formation), Garfield County, Utah

    Science.gov (United States)

    Robinson, J.W.; McCabea, P.J.

    1997-01-01

    Excellent three-dimensional exposures of the Upper Jurassic Salt Wash Sandstone Member of the Morrison Formation in the Henry Mountains area of southern Utah allow measurement of the thickness and width of fluvial sandstone and shale bodies from extensive photomosaics. The Salt Wash Sandstone Member is composed of fluvial channel fill, abandoned channel fill, and overbank/flood-plain strata that were deposited on a broad alluvial plain of low-sinuosity, sandy, braided streams flowing northeast. A hierarchy of sandstone and shale bodies in the Salt Wash Sandstone Member includes, in ascending order, trough cross-bedding, fining-upward units/mudstone intraclast conglomerates, singlestory sandstone bodies/basal conglomerate, abandoned channel fill, multistory sandstone bodies, and overbank/flood-plain heterolithic strata. Trough cross-beds have an average width:thickness ratio (W:T) of 8.5:1 in the lower interval of the Salt Wash Sandstone Member and 10.4:1 in the upper interval. Fining-upward units are 0.5-3.0 m thick and 3-11 m wide. Single-story sandstone bodies in the upper interval are wider and thicker than their counterparts in the lower interval, based on average W:T, linear regression analysis, and cumulative relative frequency graphs. Multistory sandstone bodies are composed of two to eight stories, range up to 30 m thick and over 1500 m wide (W:T > 50:1), and are also larger in the upper interval. Heterolithic units between sandstone bodies include abandoned channel fill (W:T = 33:1) and overbank/flood-plain deposits (W:T = 70:1). Understanding W:T ratios from the component parts of an ancient, sandy, braided stream deposit can be applied in several ways to similar strata in other basins; for example, to (1) determine the width of a unit when only the thickness is known, (2) create correlation guidelines and maximum correlation lengths, (3) aid in interpreting the controls on fluvial architecture, and (4) place additional constraints on input variables to

  17. Middle Ordovician brachiopods from the Stairway Sandstone, Amadeus Basin, central Australia

    DEFF Research Database (Denmark)

    Jakobsen, Kristian Grube; Brock, Glenn A.; Nielsen, Arne Thorshøj

    2014-01-01

    -water palaeoenvironment along the margin of northeastern Gondwana. The brachiopods from the Stairway Sandstone are of low diversity and represent ca 9% of the entire shelly fauna. Five brachiopod taxa are described from the Stairway Sandstone; all are endemic to the Amadeus Basin at species level. Two new species...

  18. Brief analysis on relationship between red beds and sandstone-type uranium ore-formation

    International Nuclear Information System (INIS)

    Ji Zengxian

    2006-01-01

    Red beds are sandy gravel beds deposited under the arid and hot climates and correspondent to the oxidation environment of continental basins. As an exogenetic epigenetic uranium deposit, the formation of the sandstone-type uranium deposit needs a large chronologic gap between the diagenesis and the subsequent uranium metallogenesis of the ore-hosting target layer with a sedimentary discontinuity and an alternative humid-arid climate. Red beds are the product of this time. The evolutionary times of red beds are in accordance with the formation of the sandstone-type uranium deposit. Both domestic and abroad researches indicate that each times evolution of a red bed might be associated with uranium ore-formation in one or more sandstone layers in the region. In China, red beds are developed in many geologic periods, but sandstone-type uranium mineralization occurs mostly in Mesozoic-Cenozoic. Taking five known sandstone-type uranium deposits as examples, the author makes a primary analysis on the relationship between red beds and the subsequent sandstone-type uranium mineralization. It is suggested that the deposition of red beds and sandstone-type uranium metallogenesis are of 'cogenesis and coexistence' and that the deposition of red beds and its evolutionary times can be regarded as the prerequisites to judge the potential of sandstone-type uranium mineralization in a Mesozoic-Cenozoic sedimentary basin. (authors)

  19. Analysis on metallogenic conditions of paleochannel sandstone type uranium deposits in kelulun region

    Energy Technology Data Exchange (ETDEWEB)

    Mingyue, Feng [Beijing Research Inst. of Uranium Geology, Beijing (China)

    1999-07-01

    On the basis of comprehensively analyzing metallogenic conditions of paleochannel sandstone type uranium deposits, the author discusses regional geologic background, characteristics of the basement and sedimentary cover of Kelulun basin and Huchawula-Hulun Lake basin, and the metallogenic potential of paleochannel sandstone type uranium deposits is proposed.

  20. Analysis on metallogenic conditions of paleochannel sandstone type uranium deposits in kelulun region

    International Nuclear Information System (INIS)

    Feng Mingyue

    1999-01-01

    On the basis of comprehensively analyzing metallogenic conditions of paleochannel sandstone type uranium deposits, the author discusses regional geologic background, characteristics of the basement and sedimentary cover of Kelulun basin and Huchawula-Hulun Lake basin, and the metallogenic potential of paleochannel sandstone type uranium deposits is proposed

  1. Different effects of temperature and salinity on permeability reduction by fines migration in Berea sandstone

    DEFF Research Database (Denmark)

    Rosenbrand, Esther; Kjøller, Claus; Riis, Jacob Fabricius

    2015-01-01

    Hot water injection into geothermal aquifers is considered in order to store energy seasonally. Berea sandstone is often used as a reference formation to study mechanisms that affect permeability in reservoir sandstones. Both heating of the pore fluid and reduction of the pore fluid salinity can...

  2. The Bentheim Sandstone: Geology, petrophysics, varieties and it's use as dimension stone

    NARCIS (Netherlands)

    Dubelaar, C.W.; Nijland, T.G.

    2014-01-01

    The shallow-marine Bentheim Sandstone was deposited in one of the NW-SE trending basins north of the London-Brabant and Rhenish massifs during the Valanginian (Early Cretaceous). The Bentheim Sandstone forms an important reservoir rock for petroleum, but has also proven itself as a very durable

  3. Three Versus 6 Months of Oxaliplatin-Based Adjuvant Chemotherapy for Patients With Stage III Colon Cancer: Disease-Free Survival Results From a Randomized, Open-Label, International Duration Evaluation of Adjuvant (IDEA) France, Phase III Trial.

    Science.gov (United States)

    André, Thierry; Vernerey, Dewi; Mineur, Laurent; Bennouna, Jaafar; Desrame, Jérôme; Faroux, Roger; Fratte, Serge; Hug de Larauze, Marine; Paget-Bailly, Sophie; Chibaudel, Benoist; Bez, Jeremie; Dauba, Jérôme; Louvet, Christophe; Lepere, Céline; Dupuis, Olivier; Becouarn, Yves; Mabro, May; Egreteau, Joëlle; Bouche, Olivier; Deplanque, Gaël; Ychou, Marc; Galais, Marie Pierre; Ghiringhelli, François; Dourthe, Louis Marie; Bachet, Jean-Baptiste; Khalil, Ahmed; Bonnetain, Franck; de Gramont, Aimery; Taieb, Julien

    2018-05-20

    Purpose Reduction of adjuvant treatment duration may decrease toxicities without loss of efficacy in stage III colon cancer. This could offer clear advantages to patients and health care providers. Methods In International Duration Evaluation of Adjuvant Chemotherapy (IDEA) France, as part of the IDEA international collaboration, patient with colon cancer patients were randomly assigned to 3 and 6 months of modified FOLFOX6 (mFOLFOX6: infusional fluorouracil, leucovorin, and oxaliplatin) or capecitabine plus oxaliplatin (CAPOX) by physician choice. The primary end point was disease-free survival (DFS), and analyses were descriptive. Results A total of 2,010 eligible patients received either 3 or 6 months of chemotherapy (modified intention-to-treat population); 2,000 (99%) had stage III colon cancer (N1: 75%, N2: 25%); 1,809 (90%) received mFOLFOX6, and 201 (10%) received CAPOX. The median age was 64 years, and the median follow-up time was 4.3 years. Overall, 94% (3 months) and 78% (6 months) of patients completed treatment (fluoropyrimidines ± oxaliplatin). Maximal grade 2 and 3 neuropathy rates were 28% and 8% in the 3-month arm and 41% and 25% in the 6-month arm ( P < .001). Final rates of residual neuropathy greater than grade 1 were 3% in the 3-month arm and 7% in the 6-month arm ( P < .001). There were 578 DFS events: 314 and 264 in the 3- and 6-month arms, respectively. The 3-year DFS rates were 72% and 76% in the 3- and 6-month arms, respectively (hazard ratio [HR], 1.24; 95% CI, 1.05 to 1.46; P = .0112). In the 3 and 6-month arms, respectively, for patients who received mFOLFOX6, the 3-year DFS rates were 72% and 76% (HR, 1.27; 95% CI, 1.07 to 1.51); for the T4 and/or N2 population, they were 58% and 66% (HR, 1.44; 95% CI, 1.14 to 1.82); and for the T1-3N1 population, they were 81% and 83% (HR, 1.15; 95% CI, 0.89 to 1.49). Conclusion IDEA France, in which 90% of patients received mFOLFOX6, shows superiority of 6 months of adjuvant chemotherapy compared

  4. Duration Calculus: Logical Foundations

    DEFF Research Database (Denmark)

    Hansen, Michael Reichhardt; Chaochen, Zhou

    1997-01-01

    The Duration Calculus (abbreviated DC) represents a logical approach to formal design of real-time systems, where real numbers are used to model time and Boolean valued functions over time are used to model states and events of real-time systems. Since it introduction, DC has been applied to many...

  5. Duration of load revisited

    DEFF Research Database (Denmark)

    Hoffmeyer, Preben; Sørensen, John Dalsgaard

    2007-01-01

    A duration of load study representing 13 years of testing was recently terminated. Preliminary results have been published over the years. This paper represents the final account of the study, which was focused on the influ-ence of moisture content on time to failure for structural timber subject...

  6. duration diabetes mellitus

    African Journals Online (AJOL)

    ... group, type of diabetes, age of onset and duration of diabetes), presence of retinopathy, markers of nephropathy and biochemical variables. ... type 2 diabetes and for each ethnic group. Results. ... time of diabetes diagnosis in blacks than Indians. In the type ... countries, minority groups and disadvantaged communities in.

  7. Deformation bands in porous sandstones their microstructure and petrophysical properties

    Energy Technology Data Exchange (ETDEWEB)

    Torabi, Anita

    2007-12-15

    deformation bands are characterized by strain hardening, these new bands feature a central slip surface, which indicates late strain softening. They lack the characteristic compaction envelop, and are typified by higher porosity and lower permeability than previously-described cataclastic deformation bands. Intense background fracturing of the host rock and significant initial porosity are considered to be important in creating these newly-discovered deformation bands. In a related study, we investigate, for millimeter- wide deformation bands, the scale limitation inherent in laboratory measurements of porosity and permeability. The scale limitations imposed by the deformation band relative to the physical sample size motivated us to develop a new method for determining porosity and permeability based on image processing. While plug measurements measure the effective permeability across a 25.4 mm (1 inch) long sample, which includes both host rock and deformation band, the method presented here provides a means to estimate porosity and permeability of deformation band on microscale. This method utilizes low-order (one- and two orders) spatial correlation functions to analyze high-resolution, high-magnification backscatter images, to estimate the porosity and specific surface area of the pore-grain interface in the deformed sandstones. Further, this work demonstrates the use of a modified version of the Kozeny-Carmen relation to calculate permeability by using porosity and specific surface area obtained through the image processing. The result shows that permeability difference between the band and the host rock is up to four orders of magnitude. Moreover, the porosities and permeabilities estimated from image processing are lower than those obtained from their plug measurements; hence the traditional laboratory measurements have been overestimating permeability because of the previously-unrecognized scale problem. In addition, the image processing results clearly show that

  8. The sandstone's chromatic alteration of the florentine cultural heritage

    Science.gov (United States)

    Vettori, S.; Pecchioni, E.; Cantisani, E.; Ricci, M.; Fratini, F.; Garzonio, C. A.

    2012-04-01

    Pietra Serena is one of the materials more used in Florentine architecture. It is a sandstone that outcrops in the hills north of the city in the municipality of Fiesole and it has been employed mainly for ornamental purposes. This litotype belongs to the the Macigno Formation (Oligocene Upper- Miocene Lower) which consists of beds of turbiditic sandstones separated by pelitic levels which are the finest components of each single turbidity layer. Petrographically, Pietra Serena can be defined as a medium-coarse-grained greywacke made of quartz, feldspars, micas, fragments of metamorphic and magmatic rocks. The clayey matrix is quite abundant, mainly composed by illite, kaolinite and chlorite-vermiculite (present only in some quarries). It is well known that the processes of decay of the sandstones are related to the type of matrix, the amount of cement, the kind of clay minerals and to the pore size distribution, which lead to water infiltrations, swelling of the clay minerals, separation of the clayey matrix, with resulting exfoliation and peeling of the stone artefacts. Pietra Serena has a bluish-grey colour in fresh cut, but many times it is easily oxidized acquiring an ochraceous-reddish brown colour on buildings. Such changes in colour, appear to be due in part to the oxidation of iron, proceeding very quickly from the surface to the inside, though the cohesion is not affected. It is possible to hypothesize that the chromatic changes not necessarily involve a progressive state of alteration of the artefact, but they may often to represents a natural patina acquired with the time. Nevertheless it is necessary to remember that the oxidized layer and its hardness could also be the result of treatments performed in the past. In Florence, several monuments and buildings are affected by such phenomenon, in particular it is possible to note an intense and diffuse reddish colouring on the Pietra Serena utilized for columns and for façade's decorations. In this work

  9. Elementary analysis on the main factors affecting the permeability of sandstones

    International Nuclear Information System (INIS)

    Gong Binli

    2006-01-01

    Researches show that in the early stage of sandstone diagenesis, compaction, pressure solution, cementation and replacement reduce both the porosity and the permeability. The cementation of authigenic kaolinite may preserve the tiny intergranular pore-space, and slightly influence the porosity, and even increase the permeability. During the middle to late stage of diagenesis, the organic matter becomes matured, hydrocarbon and acidic water are produced, which forms secondary porosity by the dissolution and the corrosion, and greatly increases the permeability of sandstones and provides a favorable prerequisite for the formation of sandstone-type uranium deposits. The interlayered oxidation alteration, oil-gas reduction and low-temperature hydrothermal alteration also produce secondary porosity in epigenetic reforming stage, which finally decides the permeability after the formation of sandstone-type uranium deposits. This is an important condition for in-situ leaching of sandstone-type uranium deposit. (authors)

  10. Age, sedimentary environments, and other aspects of sandstone and related host rocks for uranium deposits

    International Nuclear Information System (INIS)

    1983-01-01

    Project II of the Uranium Geology Working Group was assigned to the study of sedimentary basins and sandstone - type uranium deposits. About 40% of the worlds's uranium resources are contained in sandstone-type deposits, which has led to extensive research. The research was carried out mainly by correspondence, and the results reported by 21 geologists from 10 nations are summarized in this report. It investigated five topics dealing with important aspects of the geology of uranium ores in sandstone host formations: age of host rock; partitioning of uranium between continental and marine sediments; latitude limitation on formation of sandstone deposits; effect of rock formation dip on sandstone ores; usefulness of stable isotope and fluid inclusion studies. The results of studies on these subjects form part of a wider programme of the Working Group, whose final results will be presented at the 27th International Geological Congress in Moscow in 1984

  11. Benefits of a horizontal well in sandstone waterflood

    International Nuclear Information System (INIS)

    Hansen, K.L.

    1992-01-01

    This is a case study which describes the planning and results of a horizontal well in a shallow Wilcox sandstone waterflood unit in central Louisiana. The Tremont H-13-1 was OXY USA Inc.'s first horizontal well. Analysis will include examination of the selection criteria, planning, execution, completion, and production. A variety of well and field data is presented and reviewed to access the value of this information as it applies towards other applications. The Cruse Waterflood Unit is a 2100 ft. Wilcox formation in central Louisiana. Production improvements have been 500% or greater for the horizontal well versus adjacent vertical wells. The horizontal well paid out in less than 4 months Results from this well indicate that not only was this project an economic success, but that other fields will similar conditions can be produced in a more profitable manner with horizontal wells

  12. The influence of climate on early and burial diagenesis of Triassic and Jurassic sandstones from the Norwegian – Danish Basin

    DEFF Research Database (Denmark)

    Weibel, Rikke; Olivarius, Mette; Kjøller, Claus

    2017-01-01

    Climate changes preserved in sandstones are documented by comparing the sediment composition and early diagenetic changes in sandstones deposited during arid to semi-arid conditions, the Skagerrak Formation, with sandstones of the Gassum Formation deposited in a humid well-vegetated environment...

  13. The red bed-type and sandstone-type uranium deposits in the inland basins of the northwest China

    International Nuclear Information System (INIS)

    Wang Zhilong.

    1988-01-01

    On the basis of the study on the relationship between the red bed-type and sandstone-type uranium deposits in the inland basins of the northwest China, a classification of red beds based on sedimentary facies and redding origin is presented. Red beds in the inland badins can be divided into six types: 1. alluvial plain and 2. shallow lake red beds formed at the stage of continental disintegration; 3. fluvial alluvial red bed, 4. delta plain and 5. desert red beds formed at the diagenetic-epigenetic stage; 6. spattered red (secondaty red beds) formed at the hypergenic weathering stage. According to the characteristics, structural environments of these six types of red beds, and changes of various geochemical characteristic values (Eh, pH, Th/U, Fe 3+ /Fe 2+ , Sr/Ba, etc.) from host rocks to different kinds of red beds , the relationship between these values and sandstone-type uranium deposits was determined. it is an open system, the mobile uranium is easily leached, thus it is unfavoutable for mineralization; but when the rock reddens at the diagenetic epigenetic stage (closed system) that is favourable for mineraizaltion, the mobile uranium can be concentrated to form uranium deposits

  14. ANALYSIS OF OIL-BEARING CRETACEOUS SANDSTONE HYDROCARBON RESERVOIRS, EXCLUSIVE OF THE DAKOTA SANDSTONE, ON THE JICARILLA APACHE INDIAN RESERVATION, NEW MEXICO

    International Nuclear Information System (INIS)

    Jennie Ridgley

    2000-01-01

    A goal of the Mesaverde project was to better define the depositional system of the Mesaverde in hopes that it would provide insight to new or by-passed targets for oil exploration. The new, detailed studies of the Mesaverde give us a better understanding of the lateral variability in depositional environments and facies. Recognition of this lateral variability and establishment of the criteria for separating deltaic, strandplain-barrier, and estuarine deposits from each other permit development of better hydrocarbon exploration models, because the sandstone geometry differs in each depositional system. Although these insights will provide better exploration models for gas exploration, it does not appear that they will be instrumental in finding more oil. Oil in the Mesaverde Group is produced from isolated fields on the Chaco slope; only a few wells define each field. Production is from sandstone beds in the upper part of the Point Lookout Sandstone or from individual fluvial channel sandstones in the Menefee. Stratigraphic traps rather than structural traps are more important. Source of the oil in the Menefee and Point Lookout may be from interbedded organic-rich mudstones or coals rather than from the Lewis Shale. The Lewis Shale appears to contain more type III organic matter and, hence, should produce mainly gas. Outcrop studies have not documented oil staining that might point to past oil migration through the sandstones of the Mesaverde. The lack of oil production may be related to the following: (1) lack of abundant organic matter of the type I or II variety in the Lewis Shale needed to produce oil, (2) ineffective migration pathways due to discontinuities in sandstone reservoir geometries, (3) cementation or early formation of gas prior to oil generation that reduced effective permeabilities and served as barriers to updip migration of oil, or (4) erosion of oilbearing reservoirs from the southern part of the basin. Any new production should mimic that of

  15. Architecture and quantitative assessment of channeled clastic deposits, Shihezi sandstone (Lower Permian, Ordos Basin, China

    Directory of Open Access Journals (Sweden)

    Chengye Jia

    2017-02-01

    Full Text Available Lower Permian Shihezi sandstone in Ordos Basin is the largest gas reservoir in China. Architecture elements of channel, overbank and floodplain facies of braided channel deposits were identified through an outcrops survey, and their proportion of channel facies have been quantitatively estimated from well logging. Characteristics of architecture elements, such as sand thickness, bounding surfaces and lithofacies were investigated through outcrops and core. Petrology of Shihezi sandstone has also been studied in detail. Analysis on sandstone components shows that monocrystalline quartz with approximately 76% bulk volume, and lithic up to 5%–45% bulk volume, are the two main components. Litharenite and lithic quartz sandstone are the main rock types. Compaction is concluded by former researchers as the control factor of low permeability. Examination through thin section reveals that secondary pores developed well in coarse sand. Inter-granular dissolution is included as the positive effect to increasing porosity, and is concluded as the control factor to the generation of net pay. Scale of coarse grained channel fills and channel bar sandstone bodies are quantitatively estimated. Strike-oriented, dip-oriented, and vertical distribution of channel fills and channel bar sandstone bodies have been investigated. The geometry of sand bodies can be depicted as an elongated lens. Subsurface mapping reveals that channel sandstone bodies distribute widely from both lateral and longitudinal cross section profiles, and are poorly connected.

  16. Diagenetic controls on porosity variations within an aeolian sandstone reservoir, borehole Kudu 9A-3

    International Nuclear Information System (INIS)

    Marot, J.E.B.

    1990-01-01

    Three boreholes, Kudu 9A-1, 9A-2 and 9A-3, were drilled approximately 125 km west of the Orange River mouth to test a gas-bearing structure of Barremian age. The reservoir interval comprises an upper unit of interbedded shallow marine sandstones, limestones and volcaniclastic mass flow deposits, and a lower non-marine unit of interbedded aeolian sandstones, basaltic lavas and volcaniclastic deposits. Despite the overall good poroperm characteristics of the aeolian sandstone and its apparent mineralogical homogeneity, as implied by a gamma ray trace, the core analysis results show an extreme variation in porosity and permeability values. In order to assist in reservoir quality prediction and to assess the regional prospectivity of the sandstone, it was necessary to explain these variations. The resuls of the study indicate that compositionally and texturally the sandstones are extremely homogeneous. It is concluded that the marked variation in the poroperm characteristics of the aeolian sandstones is a result of a relatively complex diagenesis. A fluctuating water table resulted in the formation of a pattern of calcite, anhydrite and quartz cements within an aeolian dune sandstone. 7 refs., 1 fig

  17. Sedimentological Characteristics and Re-interpretation of the Paleoenvironment of Lokoja Sandstone, Southern Bida Basin, Nigeria

    International Nuclear Information System (INIS)

    Ojo, O. J.; Akande, S. O.

    2002-01-01

    Detail mapping of the Lokoja Formation consisting predominantly of sandstones exposed along Okene-Abuja highway near the confluence of Rivers Niger and Benue in the southern Bida Basin was undertaken in an attempt to reconstruct their depositional history. The analyses of the lithofacies characteristics, pebble morphogenesis and ichnofossil content of the Lokoja sandstones in the study area reveal their depositional environments which evolved from alluvial fans through braided stream into nearshore shallow marine conditions. The massive, immature, matrix to grain supported conglomerate subfacies can be interpreted as debris flow. The conglomeratic sandstone facies (massive, cross stratified and graded subfacies) reflect deposits of deep braided channels. The bioturbated and herringbone cross stratified conglomeratic sandstones indicate shallowing to marginal marine environments. The fine to medium grained sandstones, siltstones and claystones are interpreted as channel bars and floodplain deposits.Results of pebble morphogenesis analysis indicate predominance of fluvial processes. Minor high energy (probably beach) condition is indicated by some individual clasts from the conglomeratic sandstone facies with sphericity and OP index values less that 0.66 and -1.5 respectively.The study is significant because it represents the first sedimentological evidence of influence of shallow marine in the development of Lokoja sandstones during Campanian-Maastrichtian times

  18. Effects of Pisha sandstone content on solute transport in a sandy soil.

    Science.gov (United States)

    Zhen, Qing; Zheng, Jiyong; He, Honghua; Han, Fengpeng; Zhang, Xingchang

    2016-02-01

    In sandy soil, water, nutrients and even pollutants are easily leaching to deeper layers. The objective of this study was to assess the effects of Pisha sandstone on soil solute transport in a sandy soil. The miscible displacement technique was used to obtain breakthrough curves (BTCs) of Br(-) as an inert non-adsorbed tracer and Na(+) as an adsorbed tracer. The incorporation of Pisha sandstone into sandy soil was able to prevent the early breakthrough of both tracers by decreasing the saturated hydraulic conductivity compared to the controlled sandy soil column, and the impeding effects increased with Pisha sandstone content. The BTCs of Br(-) were accurately described by both the convection-dispersion equation (CDE) and the two-region model (T-R), and the T-R model fitted the experimental data slightly better than the CDE. The two-site nonequilibrium model (T-S) accurately fit the Na(+) transport data. Pisha sandstone impeded the breakthrough of Na(+) not only by decreasing the saturated hydraulic conductivity but also by increasing the adsorption capacity of the soil. The measured CEC values of Pisha sandstone were up to 11 times larger than those of the sandy soil. The retardation factors (R) determined by the T-S model increased with increasing Pisha sandstone content, and the partition coefficient (K(d)) showed a similar trend to R. According to the results of this study, Pisha sandstone can successfully impede solute transport in a sandy soil column. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. 57Fe Mössbauer and X-ray characterisation of sandstones

    International Nuclear Information System (INIS)

    Mulaba-Bafubiandi, A. F.; Waanders, F. B.

    2013-01-01

    Sandstones from the Free State province in South Africa have been mined and processed mainly by small scale and artisanal miners in the rural areas. In the present investigation basic fire proof and water absorption tests, X-ray and γ-ray based characterisation techniques were used to study the sandstones. The collected samples were grouped according to their apparent colour in day light conditions and the elemental analysis showed the presence of a high amount of oxygen (>52%) and silicon (>38%) with Mn, Al, Fe and Ca as major elements in proportions related to the colour distribution of the various sandstones. The uniaxial compressive stress was found to be the highest (56 MPa) for the greyish sandstone and the lowest (8 MPa) for the white sandstone sample, also associated with the lowest (Al+Fe)/Si value of 0.082. The humidity test showed that the 6 % water absorption was lower than the recommended ASTM value of 8 %. The sandstone samples were also subjected to various high temperatures to simulate possible fire conditions and it was found that the non alteration of the mineral species might be one of the reasons why the sandstones are regarded as the most refractory amongst the building materials typically used. Mössbauer spectroscopy revealed that iron is present in all the sandstones, mainly as Fe 3 +  with the black sandstone showing an additional presence of 3 % Fe 2 +  indicating that a higher iron content coupled to higher silicon content, contributes to an increase in the uniaxial compressive strength.

  20. Physical and chemical properties for sandstone and bentonites

    International Nuclear Information System (INIS)

    Sato, Haruo

    2004-01-01

    Physical and chemical properties such as porosity, pore-size distribution, dry density, solid density, mineralogy and chemical composition, which are important parameters for the understanding and analysis of the diffusion phenomena of radionuclides and ions in bentonite and in the geosphere, were measured. The measurements were performed for sandstone, of which fundamental data and information are limited. For bentonite, 3 kinds of bentonites with different smectite contents (Kunigel-V1, Kunipia-F, MX80) were used. In the measurements of the physical and chemical properties of rock, the measurements of solid density by pychnometer, the measurements of porosity, dry density and solid density by water saturation method, the measurements of porosity, dry density, solid density, pore-size distribution and specific surface area of pores by Hg porosimetry, the identifications of constituent minerals by X-ray Diffractometry (XRD), the measurement of chemical composition by whole rock analysis, the observations of micropore structure by Laser Confocal Microscope (LCM), the measurements of water vaporization curves and the measurements of the homogeneity of the rock by penetration of KMnO 4 were performed. While, in the measurements of the physical and chemical properties for bentonite, water basis water content, water content, porosity, dry density, solid density and their distributions in samples were measured, and the degree of inhomogeneity was quantitatively evaluated by comparing with data and information reported up to date. The porosities of sandstone are 15.6±0.21% for water saturation method and 15.5±0.2% for Hg porosimetry, and similar values were obtained in both methods. The solid densities ranged 2.65-2.69 Mg/m 3 for 3 methods, and the average value was 2.668±0.012 Mg/m 3 . The average pore size was 88.8±0.5nm, and pore sizes ≤10μm shared 80% of total pore volume and pore sizes ≤1μm shared 40%. The specific surface area of the pores is 4.09±0.017 m

  1. Duration in Production Contracts

    OpenAIRE

    MacDonald, James M.; Korb, Penelope J.

    2006-01-01

    We use 2003 and 2004 ARMS data to analyze variations in contract duration among growers of broilers who hold production contracts. Most contracts cover just a single flock, but many extend for 1-2 years, and a significant minority of broiler contracts specify lengths of 5, 10, and even 15 years. We find that grower debt and production volume are inversely related to the choice of a short term (a year or less) contract, while lengthy prior experience with the contractor promotes short term con...

  2. Facies architecture of the Bluejacket Sandstone in the Eufaula Lake area, Oklahoma: Implications for the reservoir characterization of the Bartlesville Sandstone

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Liangmiao; Yang, Kexian [Univ. of Tulsa, OK (United States)

    1997-08-01

    Outcrop studies of the Bluejacket Sandstone (Middle Pennsylvanian) provide significant insights to reservoir architecture of the subsurface equivalent Bartlesville Sandstone. Quarry walls and road cuts in the Lake Eufaula area offer excellent exposures for detailed facies architectural investigations using high-precision surveying, photo mosaics. Directional minipermeameter measurements are being conducted. Subsurface studies include conventional logs, borehole image log, and core data. Reservoir architectures are reconstructed in four hierarchical levels: multi-storey sandstone, i.e. discrete genetic intervals; individual discrete genetic interval; facies within a discrete genetic interval; and lateral accretion bar deposits. In both outcrop and subsurface, the Bluejacket (Bartlesville) Sandstone comprises two distinctive architectures: a lower braided fluvial and an upper meandering fluvial. Braided fluvial deposits are typically 30 to 80 ft thick, and are laterally persistent filling an incised valley wider than the largest producing fields. The lower contact is irregular with local relief of 50 ft. The braided-fluvial deposits consist of 100-400-ft wide, 5-15-ft thick channel-fill elements. Each channel-fill interval is limited laterally by an erosional contact or overbank deposits, and is separated vertically by discontinuous mudstones or highly concentrated mudstone interclast lag conglomerates. Low-angle parallel-stratified or trough cross-stratified medium- to coarse-grained sandstones volumetrically dominate. This section has a blocky well log profile. Meandering fluvial deposits are typically 100 to 150 ft thick and comprise multiple discrete genetic intervals.

  3. Discussion on metallogenic prospect of sandstone-type uranium deposit in Yabulai basin

    International Nuclear Information System (INIS)

    Wang Lianshe; Li Xiangping

    2003-01-01

    Based on characteristics of initial basin type and tectonic reworking process, this article analyses the distribution features of depositional system and subsequent alteration of the target horizon of sandstone-type uranium deposits in Yabulai basin. Guided by prognostic criteria of sandstone-type uranium deposits, authors suggest that the post-depositional tectonic reworking in the basin was quite intense, and uranium metallogenic prospects are unfavorable. However, the Lower Cretaceous in the paleo-slope at the middle of the basin does show certain metallogenic prospects for sandstone-type uranium deposits

  4. Quantifying the effect of squirt flow dispersion from compliant clay porosity in clay bearing sandstones

    DEFF Research Database (Denmark)

    Sørensen, Morten Kanne; Fabricius, Ida Lykke

    2013-01-01

    Compliant porosity in the form of cracks is known to cause significant attenuation and velocity dispersion through pore pressure gradients and consequent relaxation, dubbed squirt flow. Squirt flow from cracks vanish at high confining stress due to crack closing. Studies on clay bearing sandstones......-squirt flow on the bulk modulus of a clay bearing sandstone. The predicted magnitude of the clay-squirt effect on the bulk modulus is compared with experimental data. The clay-squirt effect is found to possibly account for a significant portion of the deviances from Gassmann fluid substitution in claybearing...... sandstones....

  5. Stable isotopic mass balance in sandstone-shale couplets. An example from the Neogene Pannonian Basin

    International Nuclear Information System (INIS)

    Matyas, J.; Geologisches Institut.

    1996-01-01

    Oxygen isotopic ratios of carbonate cements in the Neogene sandstones of the Pannonian Basin show distinct variations: early calcites 3-6 per mille lighter than the late calcites from the same location and depth. This shift is thought to be related to the isotopically heavy oxygen released from the mixed-layer illite/smectite during illitisation. For sandstones dominated by compactional flow, closed system mass balance calculations predict an isotopic shift comparable to that deducted from petrographic and geochemical observations. The model suggests that variations of geothermal gradient has little effect on isotopic evolution; much more significant is the sandstone: shale ratio in the couplets. (author)

  6. Preliminary study on features of mineralogical zoning of epigenetic alteration at sandstone-type uranium deposit, Dongsheng area, Ordos basin

    International Nuclear Information System (INIS)

    Xiao Xinjian; Li Ziying; Chen Anping

    2004-01-01

    Sandstone-type uranium deposits located in Dongsheng area, northern Ordos basin, occur in Zhiluo Formation, Middle Jurassic. The Zhiluo Formation is divided into two members. The lower member is further divided into two submembers. The lower submember is dominantly composed of grey sandstone being the ore-hosting horizon; the upper submember consists of grey-green sandstone and mudstone. The upper member of Zhiluo Formation is made of mottled medium-fine grained sandstone and mudstone. Through the microscopic observation and study on sandstones of Zhiluo Formation, authors have established a vertical zonation of epigenetic alteration (from the top to the bottom): the limonitization + clayization + carbonation in the mottled fine-grained sandstone of the upper member of Zhiluo Formation; the green alteration (II) (mainly the chloritization of biotite, as well as the chloritization and epidotization of feldspar) + clayization + carbonation in the grey-green sandstone of the upper submember of the lower member of Zhiluo Formation; and the green alteration (I) (mainly the epidotization of feldspar) + carbonation in grey, grey-white sandstone of the lower submember. The epigenetic alteration basically occurs in grey-green sandstone. The sandstone shows grey-green color because it contains much green biotite (not chlorite). The epigenetic alteration in sandstone layer is closely associated with the uranium ore-formation

  7. Temperature dependent elasticity and damping in dehydrated sandstone

    Science.gov (United States)

    Darling, T. W.; Struble, W.

    2013-12-01

    Work reported previously at this conference, outlining our observation of anomalously large elastic softening and damping in dehydrated Berea sandstone at elevated temperatures, has been analysed to study shear and compressional effects separately. Modeling of the sample using COMSOL software was necessary to identify modes, as the vibration spectrum of the sample is poorly approximated by a uniform isotropic solid. The first torsional mode of our evacuated, dry, core softens at nearly twice the rate of Young's modulus modes (bending and compressional) and is also damped nearly twice as strongly as temperature increases. We consider two possible models for explaining this behavior, based on the assumption that the mechanical properties of the sandstone are dominated by the framework of quartz grains and polycrystalline cementation, neglecting initially the effects of clay and feldspar inclusions. The 20cm x 2.54cm diameter core is dry such that the pressure of water vapor in the experiment chamber is below 1e-6 Torr at 70C, suggesting that surface water beyond a small number of monolayers is negligible. Our models consider (1) enhanced sliding of grain boundaries in the cementation at elevated temperature and reduced internal water content, and (2) strain microcracking of the cementatioin at low water content due to anisotropic expansion in the quartz grains. In model (1) interfaces parallel to polyhedral grain surfaces were placed in the cement bonds and assigned frictional properties. Model (2) has not yet been implemented. The overall elasticity of a 3-D several-grain model network was determined by modeling quasistatic loading and measuring displacements. Initial results with a small number of grains/bonds suggests that only the first model provides softening and damping for all the modes, however the details of the effects of defect motioin at individual interfaces as the source for the frictional properties is still being evaluated. Nonlinear effects are

  8. Application potential of sequence stratigraphy to prospecting for sandstone-type uranium deposit in continental depositional basins

    International Nuclear Information System (INIS)

    Li Shengxiang; Chen Zhaobo; Chen Zuyi; Xiang Weidong; Cai Yuqi

    2001-01-01

    Sequence stratigraphy has been widely used in hydrocarbon exploration and development, and great achievements have been achieved. However, its application to the prospecting for sandstone-type uranium deposits is just beginning. The metallogenic characteristics of sandstone-type uranium deposits and those of oil and gas are compared, and the relationship between sandstone-type uranium metallogenesis and the system tracts of sequence stratigraphy is studied. The authors propose that highest and system tracts are the main targets for prospecting interlayer oxidation zone type sandstone uranium deposits, and the incised valleys of low stand system tracts are favourable places for phreatic oxidation zone type sandstone uranium deposits, and transgressive system tracts are generally unfavorable to the formation of in-situ leachable sandstone-type uranium deposits. Finally, the authors look ahead the application potential of sequence stratigraphy to the prospecting for sandstone-type uranium deposits in continental depositional basins

  9. A Darriwilian (Middle Ordovician bivalve-dominated molluscan fauna from the Stairway Sandstone, Amadeus Basin, central Australia

    Directory of Open Access Journals (Sweden)

    Kristian G. Jakobsen

    2016-12-01

    Full Text Available A bivalve-dominated molluscan fauna is described from the Darriwilian (Middle Ordovician Stairway Sandstone, Amadeus Basin, central Australia. The fauna comprises 16 species of bivalves and rostroconchs plus six gastropod species which are treated under open nomenclature. Two new bivalves, Sthenodonta paenesymmetrica sp. nov. and Modiolopsis pojetai sp. nov., are described. The relatively low-diverse molluscan fauna constitutes around 62% of the total benthic macrofauna. Approximately 75% of the molluscs comprise bivalves, especially nuculoids, which were biogeographically restricted to low latitudes during the Ordovician. The molluscan assemblage displays a very high degree of endemism at species level, though the bivalve Sthenodonta eastii also occurs in the Georgina Basin farther to the northeast. This indicates a possible marine connective seaway between the Georgina and Amadeus basins during the Darriwilian. Nuculites, Cyrtodonta, and Modiolopsis are cosmopolitan and previously reported from North China, Avalonia, and Southern Gondwana.

  10. Desalination of salt damaged Obernkirchen sandstone by an applied DC field

    DEFF Research Database (Denmark)

    Matyščák, Ondřej; Ottosen, Lisbeth M.; Rörig-Dalgaard, Inge

    2014-01-01

    Soluble salts are considered as one of the most common causes for decay of building materials. In the present work, an electrokinetic method for desalination of sandstones from a historic warehouse was tested. The sandstones claddings were removed from the warehouse during a renovation action...... in the stones, i.e. the present investigation faces more challenges relevant to a real desalination action. Experiments were conducted with two Obernkirchen sandstones from the same warehouse, but with different levels of salt concentrations and porosity. The investigation includes removal of the most common...... salts: chlorides, nitrates, sulphates. In the experimental setup the electrodes were placed in a clay poultice: a mixture of kaolinite, calcite and distilled water. An electric direct current (DC) field was applied to the sandstone.By applying 2mA for 5–11days it was possible to reduce the chloride...

  11. Heavy mineral sorting in downwards injected Palaeocene sandstone, Siri Canyon, Danish North Sea

    DEFF Research Database (Denmark)

    Kazerouni, Afsoon Moatari; Friis, Henrik; Svendsen, Johan Byskov

    2011-01-01

    Post-depositional remobilization and injection of sand are often seen in deep-water clastic systems and has been recently recognised as a significant modifier of deep-water sandstone geometry. Large-scale injectite complexes have been interpreted from borehole data in the Palaeocene Siri Canyon...... of depositional structures in deep-water sandstones, the distinction between "in situ" and injected or remobilised sandstones is often ambiguous. Large scale heavy mineral sorting (in 10 m thick units) is observed in several reservoir units in the Siri Canyon and has been interpreted to represent the depositional...... sorting. In this study we describe an example of effective shear-zone sorting of heavy minerals in a thin downward injected sandstone dyke which was encountered in one of the cores in the Cecilie Field, Siri Canyon. Differences in sorting pattern of heavy minerals are suggested as a tool for petrographic...

  12. Application status and vistas of sequence stratigraphy to the exploration of sandstone-hosted uranium deposits

    International Nuclear Information System (INIS)

    Guo Qingyin; Chen Zuyi; Yu Jinshui; Han Shuqin

    2008-01-01

    Sequence stratigraphy is a newly developed subject based on seismostratigraphy, and has been widely applied in the exploration of hydrocarbon and other sedimentogenic mineral deposits and great achievements have been obtained. However, the application of sequence stratigraphy to the exploration of sandstone-hosted uranium deposits is just at the beginning. In this paper, some primary research achievements of sequence stratigraphy to the exploration of sandstone-hosted uranium deposits are summarized, and problems and their reasons of the application of sequence stratigraphy are discussed. Further more, according to characteristics of sandstone-hosted uranium deposits and the development of sequence stratigraphy, the application vistas of sequence stratigraphy to the exploration of sandstone-hosted uranium deposits are estimated. Finally, application directions are proposed, and some specific suggestions are given. (authors)

  13. Characteristics of isotope geology of sandstone-type uranium deposit in Turpan-Hami Basin

    International Nuclear Information System (INIS)

    Liu Hanbin; Xia Yuliang; Lin Jinrong; Fan Guang

    2003-01-01

    This paper expounds the isotope characteristics of in-situ leachable sandstone-type uranium deposit of Shihongtan in the southwestern part of Turpan-Hami basin. The results suggest that uranium mineralization age of 48 ± 2 Ma and 28 ± 4 Ma are obtained. The ages of the porphyritic granite and gneissic granite from the southwestern area are 422 ± 5 Ma and 268 ± 23 Ma. The U-Pb age of clastic zircons from ore-bearing sandstone is 283 ± 67 Ma, which is corresponding to the age of gneissic granite of the provenance area indicating the material source of uraniferous sandstone.Based. The sources are uraniferous sandstone accumulated during the deposition and the uranium leached from provenance area rocks by weathering. (authors)

  14. Local diversity versus geographical distribution of arthropods occuring in a sandstone rock labyrinth

    Czech Academy of Sciences Publication Activity Database

    Růžička, Vlastimil; Mlejnek, R.; Šmilauer, P.

    2010-01-01

    Roč. 58, č. 3 (2010), s. 533-544 ISSN 1505-2249 Institutional research plan: CEZ:AV0Z50070508 Keywords : sandstone * microclimate * paleorefugium Subject RIV: EH - Ecology, Behaviour Impact factor: 0.542, year: 2010

  15. Brittle to Semibrittle Transition in Quartz Sandstone: Energetics

    Science.gov (United States)

    Kanaya, Taka; Hirth, Greg

    2018-01-01

    Triaxial compression experiments were conducted on a quartz sandstone at effective pressures up to 175 MPa and temperatures up to 900°C. Our experiments show a transition from brittle faulting to semibrittle faulting with an increase in both pressure and temperature. The yield behavior of samples deformed in the semibrittle regime follows a compactant elliptical cap at low strain, but evolves to a dilatant Mohr-Coulomb relationship with continued compaction. Optical microscopy indicates that semibrittle deformation involves cataclastic flow through shear-enhanced compaction and grain crushing; however, transmission electron microscopy shows evidence for dislocation glide in limited portions of samples. To constrain the relative contribution of brittle and crystal plastic mechanisms, we estimate the partitioning of the inelastic work into the dissipation energy for microcracking, intergranular frictional slip, and dislocation glide. We conclude that semibrittle deformation is accommodated primarily by cataclastic mechanisms, with only a limited contribution from crystal plasticity. Mechanical data, acoustic emission records, and analysis of surface energy all indicate the activation of subcritical cracking at elevated temperature. Hence, we infer that the enhancement of subcritical cracking is responsible for the transition to semibrittle flow through promoting distributed grain-scale fractures and millimeter-scale shear bands. Subcritical cracking promotes the nucleation of microfractures at lower stresses, and the resulting decrease in flow stress retards the propagation of transgranular microfractures. Our study illuminates the important role of temperature on the micromechanics of the transition from brittle faulting to cataclastic flow in the Earth.

  16. Attrition of Tyee Formation Sandstone in a Natural Fluvial System

    Science.gov (United States)

    brandes, J. B.; Sanfilippo, J. D.; Lancaster, S. T.

    2013-12-01

    The data from this study will provide a rate of attrition with respect to change in volume, time and distance in a natural stream setting. Sandstone gravel attrition has been observed in previous studies with the use of rock tumblers, but measurements in natural systems are rare or absent. This study will use rocks with implanted passive integrated transponders (PIT) tags to track sediment movement. The study area is a natural mountain stream of approximately 4m width and 1m depth. This study is part of larger study of sediment transport. The rock volumes will be recorded prior to placement in an active channel using water displacement, the specific location along the channel will be recorded, and each tracer rock will be tracked using its individual radio frequency identification (RFID) number. Tracer rock deployment will occur before the annual high-water season. After one rainy season, the rocks will be located and removed from the stream using a radio frequency mobile radio frequency tracker. Their travel distances will be recorded and final volumes determined. Differences between initial and final volumes and travel distances will yield a distribution of attrition rates and, therefore, a mean gravel attrition rate.

  17. CO2 Storage Potential of the Eocene Tay Sandstone, Central North Sea, UK

    Science.gov (United States)

    Gent, Christopher; Williams, John

    2017-04-01

    Carbon Capture and Storage (CCS) is crucial for low-carbon industry, climate mitigation and a sustainable energy future. The offshore capacity of the UK is substantial and has been estimated at 78 Gt of CO2 in saline aquifers and hydrocarbon fields. The early-mid Eocene Tay Sandstone Member of the Central North Sea (CNS) is a submarine-fan system and potential storage reservoir with a theoretical capacity of 123 Mt of CO2. The Tay Sandstone comprises of 4 sequences, amalgamating into a fan complex 125km long and 40 km at a minimum of 1500 m depth striking NW-SE, hosting several hydrocarbon fields including Gannett A, B, D and Pict. In order to better understand the storage potential and characteristics, the Tay Sandstone over Quadrant 21 has been interpreted using log correlation and 3D seismic. Understanding the internal and external geometry of the sandstone as well as the lateral extent of the unit is essential when considering CO2 vertical and horizontal fluid flow pathways and storage security. 3D seismic mapping of a clear mounded feature has revealed the youngest sequence of the Tay complex; a homogenous sand-rich channel 12 km long, 1.5 km wide and on average 100 m thick. The sandstone has porosity >35%, permeability >5 D and a net to gross of 0.8, giving a total pore volume of 927x106 m3. The remaining three sequences are a series of stacked channels and interbedded mudstones which are more quiescent on the seismic, however, well logs indicate each subsequent sequence reduce in net to gross with age as mud has a greater influence in the early fan system. Nevertheless, the sandstone properties remain relatively consistent and are far more laterally extensive than the youngest sequence. The Tay Sandstone spatially overlaps several other potential storage sites including the older Tertiary sandstones of the Cromarty, Forties and Mey Members and deeper Jurassic reservoirs. This favours the Tay Sandstone to be considered in a secondary or multiple stacked

  18. Geophysical signature recognition of aquifuge and relatively impermeable interbed in ore-hosting sandstone layer at sandstone-type uranium deposit

    International Nuclear Information System (INIS)

    Zhao Xigang; Wu Hanning; Bai Guanjun; Zhu Huanqiao; Jia Heng

    2006-01-01

    Geophysical signature recognition of aquifuge and relatively impermeable interbed in ore-hosting aquifer has been carried out a Shihongtan uranium deposit by using comprehensive logging data. The spatial distribution of above aquifuge and impermeable interbed is discussed, and the relation of these layers to sandstone-type uranium deposit, and their impact to in-situ leach mining technology are discussed. It is suggested that the aquifuge and relatively impermeable interbed bring about significant effect to the formation of interlayer oxidation zone sandstone-type uranium deposit, as well as to in-situ leach mining of the deposit. (authors)

  19. Analyzing the Sand-fixing Effect of Feldspathic Sandstone from the Texture Characteristics

    Science.gov (United States)

    Zhang, lu; Ban, Jichang

    2018-01-01

    The purpose of this research was aimed to study the sand fixing effect of feldspathic sandstone in Mu Us Sandy Land, to provide a scienticic basis for desertification control, soil and water conservation and development of farming there. Methods of mixing feldspathic sandstone and aeolian sandy soil according to 1: 0, 1: 1, 1: 2, 1: 5, and 0: 1 mass ratioes, the graded composition and characteristics were studied with laser particle size analyzer. The result showed that these features of sand-based, loosely structured, easy to wind erosion of aeolian sandy soil were changed before feldspathic sandstone and aeolian sandy soil compounding. The <0.05 mm particle mass increased with feldspathic sandstone mass increasing. The texture presented this kind of change from sand to sandy loam to loam to silt loam. The small particle size distribution, good homogeneity and other features of aeolian sandy soil were improved to a certain degree, and the particle size distribution became broad before feldspathic sandstone and aeolian sandy soil compounding. The particle grading was continuous, and the grading characteristic was good when m(F): m(S) was 1: 5(Cu was 54.71 and Cc was 2.54) or when m(F): m(S) was 1: 2(Cu was 76.21, Cc was 1.12). The conclusion is that feldspathic sandstone has sand-fixing effect in texture characteristics, which heightens with feldspathic sandstone mass increasing, and when the mass ratio of feldspathic sandstone: aeolian sandy soil is 1: 2 or 1: 5 which compound better.

  20. Temperature Effects on Stiffness Moduli of Reservoir Sandstone from the Deep North Sea

    DEFF Research Database (Denmark)

    Orlander, Tobias; Andreassen, Katrine Alling; Fabricius, Ida Lykke

    We investigate effect of testing temperature on the dynamic frame stiffness of quartz-bearing North Sea sandstone from depths of 5 km. We show that at low stress levels, the rock frame stiffens with increasing temperature and we propose an explanation for the controlling mechanisms. While...... temperature. This is unfortunate and hence, we designed a testing program with the intension of separating and quantifying effects of temperature and stress, specifically for the sandstone material subject to this study....

  1. Remote sensing information acquisition of paleo-channel sandstone-type uranium deposit in Nuheting area

    International Nuclear Information System (INIS)

    Liu Jianjun

    2000-01-01

    The author briefly describes the genesis and ore-formation mechanism of paleo-channel sandstone-type uranium deposit in Nuheting area. Techniques such as remote sensing digital image data processing and data enhancement, as well as 3-dimension quantitative analysis of drill hole data are applied to extract information on metallogenic environment of paleo-channel sandstone-type uranium deposit and the distribution of paleo-channel

  2. Discussion on several problems on the mineralization of paleo-channel sandstone type uranium deposits

    International Nuclear Information System (INIS)

    Huang Shijie

    1997-01-01

    On the basis of comprehensively analyzing paleo-channel sandstone type uranium deposits at home and abroad, the author discusses the division of mineralization types of paleo-channel sandstone type uranium deposits, and analyzes the metallogenic geologic conditions such as regional geologic background, climatic and geomorphological conditions, basement and sedimentary cover, characteristics of paleo-valley and paleo-channel, mineralization features as well as epigenetic metallogenic process. Future prospecting direction is also proposed

  3. A method of quantitative prediction for sandstone type uranium deposit in Russia and its application

    International Nuclear Information System (INIS)

    Chang Shushuai; Jiang Minzhong; Li Xiaolu

    2008-01-01

    The paper presents the foundational principle of quantitative predication for sandstone type uranium deposits in Russia. Some key methods such as physical-mathematical model construction and deposits prediction are described. The method has been applied to deposits prediction in Dahongshan region of Chaoshui basin. It is concluded that the technique can fortify the method of quantitative predication for sandstone type uranium deposits, and it could be used as a new technique in China. (authors)

  4. Elastic Dispersion and Attenuation in Fully Saturated Sandstones: Role of Mineral Content, Porosity, and Pressures

    Science.gov (United States)

    Pimienta, Lucas; Borgomano, Jan V. M.; Fortin, Jérôme; Guéguen, Yves

    2017-12-01

    Because measuring the frequency dependence of elastic properties in the laboratory is a technical challenge, not enough experimental data exist to test the existing theories. We report measurements of three fluid-saturated sandstones over a broad frequency band: Wilkenson, Berea, and Bentheim sandstones. Those sandstones samples, chosen for their variable porosities and mineral content, are saturated by fluids of varying viscosities. The samples elastic response (Young's modulus and Poisson's ratio) and hydraulic response (fluid flow out of the sample) are measured as a function of frequency. Large dispersion and attenuation phenomena are observed over the investigated frequency range. For all samples, the variation at lowest frequency relates to a large fluid flow directly measured out of the rock samples. These are the cause (i.e., fluid flow) and consequence (i.e., dispersion/attenuation) of the transition between drained and undrained regimes. Consistently, the characteristic frequency correlates with permeability for each sandstone. Beyond this frequency, a second variation is observed for all samples, but the rocks behave differently. For Berea sandstone, an onset of dispersion/attenuation is expected from both Young's modulus and Poisson's ratio at highest frequency. For Bentheim and Wilkenson sandstones, however, only Young's modulus shows dispersion/attenuation phenomena. For Wilkenson sandstone, the viscoelastic-like dispersion/attenuation response is interpreted as squirt flow. For Bentheim sandstone, the second effect does not fully follow such response, which could be due to a lower accuracy in the measured attenuation or to the occurence of another physical effect in this rock sample.

  5. Attenuation of landfill leachate by UK Triassic sandstone aquifer materials. 1. Fate of inorganic pollutants in laboratory columns

    Science.gov (United States)

    Thornton, Steven F.; Tellam, John H.; Lerner, David N.

    2000-05-01

    The attenuation of inorganic contaminants in acetogenic and methanogenic landfill leachate by calcareous and carbonate-deficient, oxide-rich Triassic sandstone aquifer materials from the English Midlands was examined in laboratory columns. Aqueous equilibrium speciation modelling, simple transport modelling and chemical mass balance approaches are used to evaluate the key processes and aquifer geochemical properties controlling contaminant fate. The results indicate that leachate-rock interactions are dominated by ion-exchange processes, acid-base and redox reactions and sorption/precipitation of metal species. Leachate NH 4 is attenuated by cation exchange with the aquifer sediments; however, NH 4 migration could be described with a simple model using retardation factors. Organic acids in the acetogenic leachate buffered the system pH at low levels during flushing of the calcareous aquifer material. In contrast, equilibrium with Al oxyhydroxide phases initially buffered pH (˜4.5) during flushing of the carbonate-deficient sandstone with methanogenic leachate. This led to the mobilisation of sorbed and oxide-bound heavy metals from the aquifer sediment which migrated as a concentrated pulse at the leachate front. Abiotic reductive dissolution of Mn oxyhydroxides on each aquifer material by leachate Fe 2+ maintains high concentrations of dissolved Mn and buffers the leachate inorganic redox system. This feature is analogous to the Mn-reducing zones found in leachate plumes and in the experiments provides a sink for the leachate Fe load and other heavy metals. The availability of reactive solid phase Mn oxyhydroxides limits the duration of redox buffering and Fe attenuation by these aquifer sediments. Aquifer pH and redox buffering capacity exert a fundamental influence on leachate inorganic contaminant fate in these systems. The implications for the assessment of aquifer vulnerability at landfills are discussed and simple measurements of aquifer properties which

  6. ) Sediment petrographic characterisation and diagenetic pathways of the Miocene Agbada sandstone, Niger delta

    International Nuclear Information System (INIS)

    Akaegbobi, I. M; Gaupp, R.; Fischer, C.

    2003-01-01

    Combined petrophysical and petrographic investigations of he Agbada sandstone interbeds has been undertaken in order to determine the controlling factors on the reservoir quality of he paralic sandstone facies. Well logs, petrophysical data and a set of core samples from two wells located in the eastern onshore of he Niger delta spanning a depth interval of 3200 to 330m, formed the basic material for the present study. Four sandstone and siltstone facies units ranging form coastal bar sands through transgressive sands to marine claystones were identified based on petrophysical log signatures. Thin section analysis of a selected set of sandstone samples revealed essentially a unimodal, homogeneous grain size distribution of the detrital mineral components. Quantitative assessment of the mineralogical composition using point count method (300 points) revealed the predominance of dring. etrital quartz (85%) over feldspar minerals (9%) and lithic fragments (6%). A database generated from the point counting of the sandstones provided a broad perspective to the relative variations of the intergranular porosities (28%), cementation and matrix. These are remarkable indicators for low compaction. Authigenic kaoline and illite were identified. The partial leaching of detrital feldspars are responsible for the low percentages of intragranular volume (secondary porosity). The main controlling factor on the high porosity can be traced to either low compactional effects (overpressure?) or total leaching of unknown early cements. We suggest that the excellent reservoir properties of the Agbada sandstones are due to under compaction, caused by continuous long-term over pressuring

  7. Effects of Heating Rate on the Dynamic Tensile Mechanical Properties of Coal Sandstone during Thermal Treatment

    Directory of Open Access Journals (Sweden)

    Ming Li

    2017-01-01

    Full Text Available The effects of coal layered combustion and the heat injection rate on adjacent rock were examined in the process of underground coal gasification and coal-bed methane mining. Dynamic Brazilian disk tests were conducted on coal sandstone at 800°C and slow cooling from different heating rates by means of a Split Hopkinson Pressure Bar (SHPB test system. It was discovered that thermal conditions had significant effects on the physical and mechanical properties of the sandstone including longitudinal wave velocity, density, and dynamic linear tensile strength; as the heating rates increased, the thermal expansion of the sandstone was enhanced and the damage degree increased. Compared with sandstone at ambient temperature, the fracture process of heat-treated sandstone was more complicated. After thermal treatment, the specimen had a large crack in the center and cracks on both sides caused by loading; the original cracks grew and mineral particle cracks, internal pore geometry, and other defects gradually appeared. With increasing heating rates, the microscopic fracture mode transformed from ductile fracture to subbrittle fracture. It was concluded that changes in the macroscopic mechanical properties of the sandstone were result from changes in the composition and microstructure.

  8. Temperature effect on microstructure and P-wave propagation in Linyi sandstone

    International Nuclear Information System (INIS)

    Sun, Hui; Sun, Qiang; Deng, Wenni; Zhang, Weiqiang; Lü, Chao

    2017-01-01

    Highlights: • Mass loss rate, P-wave velocity change rate and damage factor increase exponentially as temperatures rise. • The damage threshold temperature of sandstone samples is 300 °C and limit temperature is 900 °C. • P-wave velocity change rate of sandstone exhibits excellent linearity with mass loss rate. • Damage factor can be well expressed by mass loss rate. - Abstract: In order to study the effect of high temperature on the sandstone, scanning electron microscope (SEM) experiments and primary wave (P-wave) velocity tests have been carried out on sandstone specimens heated to different temperature. The results showed that: (1) the mass loss rate increases exponentially with the increase of temperature and reaches 2.97% at 900 °C; (2) the P-wave velocity change rate increases exponentially with the increase of temperature while there is some fluctuation before 500 °C; (3) the damage threshold temperature of sandstone samples is 300 °C and the limit temperature is 900 °C; (4) there is a good linear relationship between the mass loss rate and the P-wave velocity change rate, and the correlation coefficient (R) of the fitting line is 0.989; (5) the damage caused by high temperature can be reflected better by the mass loss rate than P-wave velocity change rate. The results obtained in this paper will be good for predicting the properties of sandstone when exposed to high temperature.

  9. Characteristics and model of sandstone type uranium deposit in south of Songliao basin

    International Nuclear Information System (INIS)

    Yu Wenbin; Yu Zhenqing

    2010-01-01

    Through analyzing the uranium deposit tectonic environment, upper cretaceous sequence stratigraphy, depositional system, evolutionary characteristics of sand bodies, the effect of subsequent transformation and the characteristic of uranium deposit, the sandstone type uranium deposit in southern basin is different from typical interlayer oxidation zone sandstone type uranium deposit. The formation and evolution of sandstone-type uranium deposit are controlled by structure fensters; the favorable sedimentary facies type is braided river facies, and the ore body is braided river sand body. The size of uranium deposits is controlled by the local oxidation zone with the characteristics of sandstone type uranium deposit in partial oxidation zone. Uranium ore bodies which distribute in the roof wings of structure fenstes, and occur in gray layers between the upper and lower oxidation zone, showing tabular, and the plate of uranium ore body is controlled by the local oxidation zone. Based on the geological features of sandstone-type uranium deposits, the metallogenic model of local oxidation zones sandstone-type uranium deposits has been set up in the south of Songliao Baisn. (authors)

  10. Geohydrology of the Navajo sandstone in western Kane, southwestern Garfield, and southeastern Iron counties, Utah

    Science.gov (United States)

    Freethey, G.W.

    1988-01-01

    The upper Navajo and Lamb Point aquifers in the Navajo Sandstone are the principal source of water for the city of Kanab, irrigation, stock, and for rural homes in the study area. Well logs and outcrop descriptions indicate the Navajo Sandstone consists of the Lamb Point Tongue and an unnamed upper member that are separated by the Tenney Canyon Tongue of the Kayenta Formation. The main Kayenta Formation underlies the Lamb Point Tongue. The Lamb Point Tongue and the upper member of the Navajo Sandstone are saturated and hydraulically connected through the Tenney Canyon Tongue. Available data indicate that precipitation percolates to the groundwater reservoir where the Navajo Sandstone crops out. Estimates of the rate of recharge at the outcrop range from 0.1 to as much as 2.8 in/yr. Water level data indicate that water moves from the upper member of the Navajo Sandstone, through the Tenney Canyon Tongue, and into the Lamb Point Tongue. Lateral flow is generally from the outcrop areas toward the incised canyons formed by tributaries of Kanab Creek and Johnson Wash. Direction and rate of groundwater movement and the location and character of the natural hydrologic boundaries in the northern part of the area where the Navajo Sandstone is buried cannot be determined conclusively without additional water level data. (Author 's abstract)

  11. Issue of CILRT duration

    International Nuclear Information System (INIS)

    Dougan, J.R.

    1983-01-01

    Containment Integrated Leakage Rate Tests (CILRTs) represent large investments of time and money on the part of the utilities operating nuclear power plants. In the early days of containment testing, leak rate tests were conducted from a minimum of 24 hours to a maximum of several days. The minimum time period of 24 hours was adopted and continues to form the fundamental approach of the Nuclear Regulatory Commission (NRC). However, there does not appear to be technical justification for the minimum test period of 24 hours. In fact, several industry sources have shown that successful CILRTs can be conducted in much less time. The NRC has recognized this fact and has approved CILRTs of less than 24 hours. But some utilities still feel constrained to use the 24 hour test due to their Technical Specifications. And although criteria for determining the duration of a CILRT have been published, no specific criteria have been agreed upon as final. Therefore, it is the purpose of this paper to highlight several of the proposed criteria and the concerns that might arise following the implementation of such criteria

  12. TOUGHREACT Testing in High Ionic Strength Brine Sandstone Systems

    International Nuclear Information System (INIS)

    Xu, Tianfu

    2008-01-01

    Deep saline formations and oil and gas reservoirs often contain concentrated brine solutions of ionic strength greater than 1 (I > 1 M). Geochemical modeling, involving high ionic strength brines, is a challenge. In the original TOUGHREACT code (Xu et al., 2004; Xu et al., 2006), activity coefficients of charged aqueous species are computed using an extended Debye-Huckel (DH) equation and parameters derived by Helgeson et al. (1981). The DH model can deal with ionic strengths from dilute to moderately saline water (up to 6 molal for an NaCl-dominant solution). The equations implemented for the DH model are presented in Appendix A. During the course of the Yucca Mountain project, a Pitzer ion-interaction model was implemented into TOUGHREACT. This allows the application of this simulator to problems involving much more concentrated aqueous solutions, such as those involving geochemical processes in and around high-level nuclear waste repositories where fluid evaporation and/or boiling is expected to occur (Zhang et al., 2007). The Pitzer ion-interaction model, which we refer to as the Pitzer virial approach, and associated ion-interaction parameters have been applied successfully to study non-ideal concentrated aqueous solutions. The formulation of the Pitzer model is presented in Appendix B; detailed information can be founded in Zhang et al. (2007). For CO 2 geological sequestration, the Pitzer ion-interaction model for highly concentrated brines was incorporated into TOUGHREACT/ECO2N, then was tested and compared with a previously implemented extended Debye-Hueckel (DH) ion activity model. The comparison was made through a batch geochemical system using a Gulf Coast sandstone saline formation

  13. Laboratory-determined transport properties of Berea sandstone

    International Nuclear Information System (INIS)

    Daily, W.D.; Lin, W.

    1985-01-01

    The authors report laboratory measurements of electrical resistivity water permeability k, and compressional wave velocity V/sub p/ for both intact and fractured Berea sandstone samples as functions of temperature from 20 C to 200 C and effective pressure P/sub e/ from 2.5 MPa to 50 MPa. For the intact sample, V/sub p/ increases from 3.52 km/s to 4.16 km/s as P/sub e/ goes from 3 to 50 MPa. With increasing temperature, V/sub p/ decreases at rates of about 3% per 100 C at P/sub e/ of 5 MPa and about 1.5% per 100 C at P/sub e/ of 38 MPa. Data from the fractured sample are qualitatively similar, but velocities are about 10% lower. For both intact and fractured samples, p increases less than 15% as P/sub e/ increases from 2.5 MPa to 50 MPa. Although both samples show a larger decrease in resistivity with increasing temperature, most of this change is attributed to the decrease in resistivity of the pore fluid over that temperature range. For both samples, k decreases with increasing pressure and temperature. The intact sample permeability varies from 23 mD at 3 MPa and 20 C to less than 1 mD at 50 MPa and 150 C. The permeability of the fractured sample varies from 676 mD at 3 MPa and 20 C to less than 1 mD at 40 MPa and 190 C. The effect of the fracture on k vanishes after several pressure cycles and above about 100 C. These laboratory data are used to demonstrate the possibility of using resistivity and velocity measurements to estimate in-situ permeability of a reservoir. 25 references, 10 figures

  14. The influence of clay minerals on acoustic properties of sandstones

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, Olav

    1997-12-31

    This thesis aims to provide better understanding of the relationship between the acoustic properties and the petrophysical/mineralogical properties in sand-prone rock. It emphasizes the influence of clay minerals. The author develops a method to deposit clay minerals/mineral aggregates in pore space of a rigid rock framework. Kaolinite aggregates were flushed into porous permeable Bentheimer sandstone to evaluate the effect of pore filling minerals on porosity, permeability and acoustic properties. The compressional velocity was hardly affected by the clay content and it was found that the effect of minor quantities of pore filling minerals may be acoustically modelled as an ideal suspension, where the pore fluid bulk modulus is modified by the bulk modulus of the clay minerals. The influence of clays on acoustic velocities in petroleum reservoir rocks was investigated through ultrasonic measurements of compressional- and shear-waves on core material from reservoir and non-reservoir units on the Norwegian Continental Shelf. The measured velocities decrease as the porosity increases, but are not strongly dependent on the clay content. The measured velocities are less dependent on the petrophysical and lithological properties than indicated by previous authors and published mathematical models, and stiffness reduction factors are introduced in two of the models to better match the data. Velocities are estimated along the wellbores based on non-sonic well logs and reflect well the actual sonic log well measurements. In some wells the compressional velocity cannot be modelled correctly by the models suggested. Very high compressional wave anisotropy was measured in the dry samples at atmospheric conditions. As the samples were saturated, the anisotropy was reduced to a maximum of about 30% and decreases further upon pressurization. Reservoir rocks retrieved from 2500 m are more stress dependent than those retrieved from less than 200 m depth. 168 refs., 117 figs., 24

  15. GREYBULL SANDSTONE PETROLEUM POTENTIAL ON THE CROW INDIAN RESERVATION, SOUTH-CENTRAL MONTANA

    Energy Technology Data Exchange (ETDEWEB)

    David A. Lopez

    2000-12-14

    Evaluation of the Lower Cretaceous Greybull Sandstone on the Crow Indian Reservation for potential stratigraphic traps in the valley-fill sandstone was the focus of this project. The Crow Reservation area, located in south-central Montana, is part of the Rocky Mountain Foreland structural province, which is characterized by Laramide uplifts and intervening structural basins. The Pryor and Bighorn mountains, like other foreland uplifts, are characterized by asymmetrical folds associated with basement-involved reverse faults. The reservation area east of the mountains is on the northwestern flank of the Powder River Basin. Therefore, regional dips are eastward and southeastward; however, several prominent structural features interrupt these regional dips. The nearly 4,000 mi{sup 2} reservation is under explored but has strong potential for increased oil and gas development. Oil and gas production is well established in the Powder River Basin of Wyoming to the south as well as in the areas north and west of the reservation. However, only limited petroleum production has been established within the reservation. Geologic relations and trends indicate strong potential for oil and gas accumulations, but drilling has been insufficient for their discovery. The Greybull Sandstone, which is part of the transgressive systems tract that includes the overlying Fall River Sandstone, was deposited on a major regional unconformity. The erosional surface at the base of the Greybull Sandstone is the +100 Ma, late Aptian-Early Albian regional unconformity of Weimer (1984). This lowstand erosional surface was controlled by a basin-wide drop in sea level. In areas where incised Greybull channels are absent, the lowstand erosional unconformity is at the base of the Fall River Sandstone and equivalent formations. During the pre-Greybull lowstand, sediment bypassed this region. In the subsequent marine transgression, streams began to aggrade and deposit sand of the lower Greybull Sandstone

  16. ANALYSIS OF OIL-BEARING CRETACEOUS SANDSTONE HYDROCARBON RESERVOIRS, EXCLUSIVE OF THE DAKOTA SANDSTONE, ON THE JICARILLA APACHE INDIAN RESERVATION, NEW MEXICO

    International Nuclear Information System (INIS)

    Jennie Ridgley

    2000-01-01

    An additional 450 wells were added to the structural database; there are now 2550 wells in the database with corrected tops on the Juana Lopez, base of the Bridge Creek Limestone, and datum. This completes the structural data base compilation. Fifteen oil and five gas fields from the Mancos-ElVado interval were evaluated with respect to the newly defined sequence stratigraphic model for this interval. The five gas fields are located away from the structural margins of the deep part of the San Juan Basin. All the fields have characteristics of basin-centered gas and can be considered as continuous gas accumulations as recently defined by the U.S. Geological Survey. Oil production occurs in thinly interbedded sandstone and shale or in discrete sandstone bodies. Production is both from transgressive and regressive strata as redefined in this study. Oil production is both stratigraphically and structurally controlled with production occurring along the Chaco slope or in steeply west-dipping rocks along the east margin of the basin. The ElVado Sandstone of subsurface usage is redefined to encompass a narrower interval; it appears to be more time correlative with the Dalton Sandstone. Thus, it was deposited as part of a regressive sequence, in contrast to the underlying rock units which were deposited during transgression

  17. Duration judgements over multiple elements

    Directory of Open Access Journals (Sweden)

    Inci eAyhan

    2012-11-01

    Full Text Available We investigated the limits of the number of events observers can simultaneously time. For single targets occurring in one of eight positions sensitivity to duration was improved for spatially pre-cued items as compared to post-cued items indicating that exogenous driven attention can improve duration discrimination. Sensitivity to duration for pre-cued items was also marginally better for single items as compared to eight items indicating that even after the allocation of focal attention, distracter items can interfere with the encoding of duration. For an eight item array discrimination was worse for post-cued locations as compared to pre-cued locations indicating both that attention can improve duration discrimination performance and that it was not possible to access a perfect memory trace of the duration of eight elements. The interference from the distracters in the pre-cued eight item array may reflect some mandatory averaging of target and distracter events. To further explore duration averaging we asked subjects to explicitly compare average durations of multiple item arrays against a single item standard duration. Duration discrimination thresholds were significantly lower for single elements as compared to multiple elements, showing that averaging, either automatically or intentionally, impairs duration discrimination. There was no set size effect. Performance was the same for averages of two and eight items, but performance with even an average of two items was worse than for one item. This was also true for sequential presentation indicating poor performance was not due to limits on the division of attention across items. Rather performance appears to be limited by an inability to remember or aggregate duration information from two or more items. Although it is possible to manipulate perceived duration locally, there appears to be no perceptual mechanisms for aggregating local durations across space.

  18. Sedimentological reservoir characteristics of the Paleocene fluvial/lacustrine Yabus Sandstone, Melut Basin, Sudan

    Science.gov (United States)

    Mahgoub, M. I.; Padmanabhan, E.; Abdullatif, O. M.

    2016-11-01

    Melut Basin in Sudan is regionally linked to the Mesozoic-Cenozoic Central and Western African Rift System (CWARS). The Paleocene Yabus Formation is the main oil producing reservoir in the basin. It is dominated by channel sandstone and shales deposited in fluvial/lacustrine environment during the third phase of rifting in the basin. Different scales of sedimentological heterogeneities influenced reservoir quality and architecture. The cores and well logs analyses revealed seven lithofacies representing fluvial, deltaic and lacustrine depositional environments. The sandstone is medium to coarse-grained, poorly to moderately-sorted and sub-angular to sub-rounded, arkosic-subarkosic to sublitharenite. On the basin scale, the Yabus Formation showed variation in sandstone bodies, thickness, geometry and architecture. On macro-scale, reservoir quality varies vertically and laterally within Yabus Sandstone where it shows progressive fining upward tendencies with different degrees of connectivity. The lower part of the reservoir showed well-connected and amalgamated sandstone bodies, the middle to the upper parts, however, have moderate to low sandstone bodies' connectivity and amalgamation. On micro-scale, sandstone reservoir quality is directly affected by textures and diagenetic changes such as compaction, cementation, alteration, dissolution and kaolinite clays pore fill and coat all have significantly reduced the reservoir porosity and permeability. The estimated porosity in Yabus Formation ranges from 2 to 20% with an average of 12%; while permeability varies from 200 to 500 mD and up to 1 Darcy. The understanding of different scales of sedimentological reservoir heterogeneities might contribute to better reservoir quality prediction, architecture, consequently enhancing development and productivity.

  19. Coastal dune facies, Permian Cutler Formation (White Rim Sandstone), Capitol Reef National Park area, southern Utah

    Science.gov (United States)

    Kamola, Diane L.; Chan, Marjorie A.

    1988-04-01

    The Permian Cutler Formation (White Rim Sandstone) in the Capitol Reef National Park area in southern Utah is an excellent example of a coastal dune complex subjected to periodic flooding by marine waters. Wind-ripple, grainfall and grainflow laminae compose the cross-sets deposited by eolian dunes. However, wave-reworked structures such as oscillation ripples, the occurrence of the characteristically marine trace fossils Thalassinoides and Chondrites, and interfingering marine carbonate beds of the Kaibab Formation collectively indicate marine interaction with the eolian environment. Four facies are distinguished: cross-stratified sandstone, burrowed to bioturbated sandstone, brecciated and deformed sandstone, and ripple-laminated sandstone and thin carbonate beds. One unusual aspect of the cross-stratified sandstone facies is the abundance of coarse-grained sand. Coarse-grained sand is atypical in many ancient eolian slipface deposits, but occurs here in large slipface foresets as both grainflow and wind-ripple deposits. No water-laid structures are found in these slipface deposits. Coarse-grained sand was probably transported to the Cutler shoreline by fluvial systems draining the Uncompahgre Uplift to the east, and then concentrated as coarse-grained ripples in interdune areas. Some of these coarse-grained ripples migrated up the stoss side of the dunes and accumulations of coarse-grained sand avalanched down the crest to form grainflow deposits. An extensive amount of soft-sediment deformation is indicated by the presence of convolute bedding and brecciation. These features occur near the zone of interfingering with marine carbonate beds of the Kaibab Formation. The water-saturated and moist conditions required for extensive deformation may have been controlled by the proximity of these sandstones to the shoreline, and fluctuations in the associated groundwater table.

  20. Frictional behaviour of sandstone: A sample-size dependent triaxial investigation

    Science.gov (United States)

    Roshan, Hamid; Masoumi, Hossein; Regenauer-Lieb, Klaus

    2017-01-01

    Frictional behaviour of rocks from the initial stage of loading to final shear displacement along the formed shear plane has been widely investigated in the past. However the effect of sample size on such frictional behaviour has not attracted much attention. This is mainly related to the limitations in rock testing facilities as well as the complex mechanisms involved in sample-size dependent frictional behaviour of rocks. In this study, a suite of advanced triaxial experiments was performed on Gosford sandstone samples at different sizes and confining pressures. The post-peak response of the rock along the formed shear plane has been captured for the analysis with particular interest in sample-size dependency. Several important phenomena have been observed from the results of this study: a) the rate of transition from brittleness to ductility in rock is sample-size dependent where the relatively smaller samples showed faster transition toward ductility at any confining pressure; b) the sample size influences the angle of formed shear band and c) the friction coefficient of the formed shear plane is sample-size dependent where the relatively smaller sample exhibits lower friction coefficient compared to larger samples. We interpret our results in terms of a thermodynamics approach in which the frictional properties for finite deformation are viewed as encompassing a multitude of ephemeral slipping surfaces prior to the formation of the through going fracture. The final fracture itself is seen as a result of the self-organisation of a sufficiently large ensemble of micro-slip surfaces and therefore consistent in terms of the theory of thermodynamics. This assumption vindicates the use of classical rock mechanics experiments to constrain failure of pressure sensitive rocks and the future imaging of these micro-slips opens an exciting path for research in rock failure mechanisms.

  1. Characterization of a fluvial aquifer at a range of depths and scales: the Triassic St Bees Sandstone Formation, Cumbria, UK

    Science.gov (United States)

    Medici, Giacomo; West, L. J.; Mountney, N. P.

    2018-03-01

    Fluvial sedimentary successions represent porous media that host groundwater and geothermal resources. Additionally, they overlie crystalline rocks hosting nuclear waste repositories in rift settings. The permeability characteristics of an arenaceous fluvial succession, the Triassic St Bees Sandstone Formation in England (UK), are described, from core-plug to well-test scale up to 1 km depth. Within such lithified successions, dissolution associated with the circulation of meteoric water results in increased permeability ( K 10-1-100 m/day) to depths of at least 150 m below ground level (BGL) in aquifer systems that are subject to rapid groundwater circulation. Thus, contaminant transport is likely to occur at relatively high rates. In a deeper investigation (> 150 m depth), where the aquifer has not been subjected to rapid groundwater circulation, well-test-scale hydraulic conductivity is lower, decreasing from K 10-2 m/day at 150-400 m BGL to 10-3 m/day down-dip at 1 km BGL, where the pore fluid is hypersaline. Here, pore-scale permeability becomes progressively dominant with increasing lithostatic load. Notably, this work investigates a sandstone aquifer of fluvial origin at investigation depths consistent with highly enthalpy geothermal reservoirs ( 0.7-1.1 km). At such depths, intergranular flow dominates in unfaulted areas with only minor contribution by bedding plane fractures. However, extensional faults represent preferential flow pathways, due to presence of high connective open fractures. Therefore, such faults may (1) drive nuclear waste contaminants towards the highly permeable shallow (< 150 m BGL) zone of the aquifer, and (2) influence fluid recovery in geothermal fields.

  2. A special kind of sandstone-type uranium deposit related to Jurassic palaeochannel systems in the northeastern Ordos Basin, China

    International Nuclear Information System (INIS)

    Li Ziying; Fang Xiheng; Xia Yuliang; Sun Ye; Jiao Yangquan; Chen Anping; Zhang Ke

    2010-01-01

    Dongsheng sandstone-type uranium deposit is a large one discovered in recent years in the northeastern Ordos Basin, China. It is a special kind of sandstone-type uranium deposit,different from other ordinary sandstone-type deposits because of its unique signatures. It is generally controlled by a transitional zone between greenish and grayish sandstones, both of those two kinds of sandstones now indicate reduced geochemical environments. The greenish color of the palaeo-oxidized sandstones mainly results from chloritization and epidotization related to oil and gas secondary reduction processes. The deposit genetically is different from ordinary sandstone uranium deposits,which is of more complex origin,undergoing not only palaeo-oxidization mineralization process, but also oil-gas fluid and hydrothermal reworking processes. It is spatially related to Jurassic Zhiluo Formation with braided palaeo channel systems. The uranium mineralization zone with higher grade usually exists in the branching area of the distributary channels of main braided streams, whose sandstone heterogeneity shows a transfer sedimentary facies from the braided stream sedimentary system to the braided delta sedimentary system. Statistical results show that medium and fine-grained sandstones are the most favorable rock types for uranium mineralization. (authors)

  3. Analysis on depositional system and prospect of sandstone-type uranium deposits of Bayanhua formation in Yilemen basin

    International Nuclear Information System (INIS)

    Sun Zexuan; Li Guoxin; He Fayang; Wei Yunjie

    2002-01-01

    Yilemen basin is a typical Mesozoic intra-mountain one. The author analyses characteristics of depositional system and the prospect of sandstone-type uranium deposit in the sedimentary cover of the Bayanhua Formation, Lower Cretaceous. Authors suggest that the conglomerate, sandstone-conglomerate and sandstone beds of braided stream and delta are favourable horizons for locating phreatic and interlayer oxidation zone sandstone-type uranium deposits, i.e. the northwestern side of Dalai uplifted zone, the Chagantaigebuqi narrow sag, and the southern area of Baolinbuqi

  4. Cathodoluminescence, fluid inclusions and trace element data for the syntaxial quartz cementation in the sandstones of Ora Formation, northern Iraq

    DEFF Research Database (Denmark)

    Omer, Muhamed Fakhri; Friis, Henrik

    2018-01-01

    Quartz cements of the quartz arenitic sandstones from the Chalky Nasara and Ora section of the (Devonian-Carboniferous) Ora Formation in northern Iraq have been studied. A combination of Hot-Cathodoluminescence (CL), LA-ICP-MS and fluid inclusions microthermometry revealed three syntaxial quartz......-bedded sandstones than in the6 thickly-bedded sandstones filling most of remaining pore space during mesogenesis. The Q3 was formed during early telogenesis stage fully cementing the sandstones and the fractures were filled by hydrothermal chlorite and sulfides. Significant amount of trace elements Al, Li, Ge...

  5. Estimation of uranium migration parameters in sandstone aquifers.

    Science.gov (United States)

    Malov, A I

    2016-03-01

    The chemical composition and isotopes of carbon and uranium were investigated in groundwater samples that were collected from 16 wells and 2 sources in the Northern Dvina Basin, Northwest Russia. Across the dataset, the temperatures in the groundwater ranged from 3.6 to 6.9 °C, the pH ranged from 7.6 to 9.0, the Eh ranged from -137 to +128 mV, the total dissolved solids (TDS) ranged from 209 to 22,000 mg L(-1), and the dissolved oxygen (DO) ranged from 0 to 9.9 ppm. The (14)C activity ranged from 0 to 69.96 ± 0.69 percent modern carbon (pmC). The uranium content in the groundwater ranged from 0.006 to 16 ppb, and the (234)U:(238)U activity ratio ranged from 1.35 ± 0.21 to 8.61 ± 1.35. The uranium concentration and (234)U:(238)U activity ratio increased from the recharge area to the redox barrier; behind the barrier, the uranium content is minimal. The results were systematized by creating a conceptual model of the Northern Dvina Basin's hydrogeological system. The use of uranium isotope dating in conjunction with radiocarbon dating allowed the determination of important water-rock interaction parameters, such as the dissolution rate:recoil loss factor ratio Rd:p (a(-1)) and the uranium retardation factor:recoil loss factor ratio R:p in the aquifer. The (14)C age of the water was estimated to be between modern and >35,000 years. The (234)U-(238)U age of the water was estimated to be between 260 and 582,000 years. The Rd:p ratio decreases with increasing groundwater residence time in the aquifer from n × 10(-5) to n × 10(-7) a(-1). This finding is observed because the TDS increases in that direction from 0.2 to 9 g L(-1), and accordingly, the mineral saturation indices increase. Relatively high values of R:p (200-1000) characterize aquifers in sandy-clayey sediments from the Late Pleistocene and the deepest parts of the Vendian strata. In samples from the sandstones of the upper part of the Vendian strata, the R:p value is ∼ 24, i.e., sorption processes are

  6. Apxs Chemical Composition of the Kimberley Sandstone in Gale Crater

    Science.gov (United States)

    Gellert, R.; Boyd, N.; Campbell, J. L.; VanBommel, S.; Thompson, L. M.; Schmidt, M. E.; Berger, J. A.; Clark, B. C.; Grotzinger, J. P.; Yen, A. S.; Fisk, M. R.

    2014-12-01

    Kimberley was chosen as a major waypoint of the MSL rover Curiosity on its way to Mount Sharp. APXS data before drilling showed interestingly high K, Fe and Zn. This warranted drilling of the fine-grained sandstone for detailed investigations with SAM and Chemin. With significantly lower Na, Al and higher K, Mg and Fe, the composition of the drill target Windjana is very distinct from the previous ones in the mudstones at Yellowknife Bay. Up to 2000 ppm Br and 4000 ppm Zn post-brush were among the highest measured values in Gale Crater. The excavated fines, stemming from about 6cm, showed lower Br, but even higher Zn. Preliminary Chemin results indicate K-feldspar and magnetite being major mineral phases in Windjana, which is consistent with the pre drill APXS result and derived CIPW norms. Inside the accessible work volume of the arm at the drill site ChemCam exposed a greyish, shinier patch of rock underneath the dust, dubbed Stephen. ChemCam sees a high Mn signal in most of the spots. An APXS integration revealed high MnO as well (~4%), in addition to high Mg, Cl,K,Ni,Zn,Br,Cu,Ge and for the first time an APXS detectable amount of ~300 ppm Co. The surface might reflect a thin surface layer and may underestimate the higher Z elemental concentration since the APXS analysis assumes an infinite sample. Important elemental correlations are likely not impacted. A four spot daytime raster of Stephen before leaving the drill site showed a good correlation of Mn with Zn, Cu and Ni. All spots have 3-3.5% Cl, the highest values measured on Mars so far. While the stratigraphic setting of the Stephen sample is discussed elsewhere, the similarity with Mn deep-sea nodules is striking, e.g. the APXS calibration sample GBW07296. Whatever process formed Stephen, the process of Mn scavenging high Z trace metals from solutions seems to have happened similarly at this site on Mars.

  7. The sedimentology of uranium-bearing sandstones on the farm Ryst Kuil 351 Beaufort West area

    International Nuclear Information System (INIS)

    Cole, D.I.

    1979-06-01

    A study of the sedimentology of some uranium-bearing sandstones on the farm Ryst Kuil 351 was made in order to assess possible relationships between the mineralisation and the sedimentary facies and/or the palaeo-environment. Use was made of 6 vertical profiles, derived from horizontal traverses. 12 sedimentary facies were recognised according to grain-size and sedimentary structure. The transitions between these facies, as derived from the vertical profiles, were subjected to Markov analysis. Only 3 Markov-dependent transitions were derived, but several facies transitions and associations occurred with greater than random frequency. These, together with the vertical profiles, were used to interpret the palaeo-environmental succession. This succession is fluvial meandering and two sub-environments - channel and flood plain - were delineated according to the prevalence of sandstone or mudstone facies. The uranium-bearing sandstones occur in the lower part of a thick (29 - 46m) multistorey point bar sequence within the channel sub-environment. The mineralisation is associated with koffieklip and is restricted to two sedimentary facies - massive very fine-to-finegrained sandstone and horizontally bedded, very fine- to fine-grained sandstone. The mineralisation normally occurs near the bases of the point bars

  8. Experimental Investigation on Shock Mechanical Properties of Red Sandstone under Preloaded 3D Static Stresses

    Directory of Open Access Journals (Sweden)

    Niu Yong

    2015-11-01

    Full Text Available Triaxial impact mechanical performance experiment was performed to study the mechanical properties of red sandstone subjected to three-dimensional (3D coupled static and dynamic loads, i.e., three confining pressures (0, 5, and 10 MPa and three axial pressures (11, 27, and 43 MPa. A modified 3D split Hopkinson pressure bar testing system was used. The change trend in the deformation of red sandstone and the strength and failure modes under axial pressures and confining pressures were analyzed. Results show that, when the confining pressure is constant, the compressive strength, secant modulus, and energy absorbed per unit volume of red sandstone initially increases and subsequently decreases, whereas the average strain rate exhibits an opposite trend. When the axial pressure is constant, both the compressive strength and secant modulus of red sandstone are enhanced, but the average strain rate is decreased with increasing confining pressure. The energy absorbed per unit volume is initially increased and subsequently decreased as the confining pressure increases. Red sandstone exhibits a cone-shaped compression–shear failure mode under the 3D coupled static and dynamic loads. The conclusions serve as theoretical basis on the mechanical properties of deep medium-strength rock under a high ground stress and external load disturbance condition

  9. Distribution of K, Na, Th and U in sandstones and shales from western Shikoku, Japan

    International Nuclear Information System (INIS)

    Ishihara, Shunso; Sakamaki, Yukio; Mochizuki, Tsunekazu; Terashima, Shigeru; Endo, Yuji

    1981-01-01

    The regional variation of K, Na, Th and U distributions was studied on 58 sandstones, 81 shales and 3 green schists from the sedimentary terrains across western Shikoku. The geological structure of the studied district is explained. The regional characteristics of the sedimentary rocks are best demonstrated in the composition of the sandstones. The sandstones, in the source areas of which granitic and rhyolitic rocks exist and which have been deposited rapidly, were rich in K, whereas those derived mainly from mafic volcanic areas showed high Na content. The sandstones of the Shimanto Supergroup had the intermediate values, and K and K + Na contents became low in the south where the younger Upper Shimanto Group is exposed. Th and U in both sandstones and shales were highest in the Izumi Group, and generally low in the Shimanto Supergroup. The black shales of the Shimanto Supergroup did not show U-anomaly. In each group, highly matured rocks gave slightly higher Th/U ratio. Highly matured polycyclic sediments contained the least amount of radioactive elements. The radioactive anomaly due to the anomalous K contained in sericite, and that due to U in black shale were found in Chichibu and Sambosan belts. Similar anomaly was discovered in the foot wall of Mn deposits in the same zone. The possibility of anomalous U may be the least in the Shimanto Supergroup. (Kako, I.)

  10. Sandstone-filled normal faults: A case study from central California

    Science.gov (United States)

    Palladino, Giuseppe; Alsop, G. Ian; Grippa, Antonio; Zvirtes, Gustavo; Phillip, Ruy Paulo; Hurst, Andrew

    2018-05-01

    Despite the potential of sandstone-filled normal faults to significantly influence fluid transmissivity within reservoirs and the shallow crust, they have to date been largely overlooked. Fluidized sand, forcefully intruded along normal fault zones, markedly enhances the transmissivity of faults and, in general, the connectivity between otherwise unconnected reservoirs. Here, we provide a detailed outcrop description and interpretation of sandstone-filled normal faults from different stratigraphic units in central California. Such faults commonly show limited fault throw, cm to dm wide apertures, poorly-developed fault zones and full or partial sand infill. Based on these features and inferences regarding their origin, we propose a general classification that defines two main types of sandstone-filled normal faults. Type 1 form as a consequence of the hydraulic failure of the host strata above a poorly-consolidated sandstone following a significant, rapid increase of pore fluid over-pressure. Type 2 sandstone-filled normal faults form as a result of regional tectonic deformation. These structures may play a significant role in the connectivity of siliciclastic reservoirs, and may therefore be crucial not just for investigation of basin evolution but also in hydrocarbon exploration.

  11. An experimental study of the response of the Galesville sandstone to simulated CAES conditions

    Energy Technology Data Exchange (ETDEWEB)

    Erikson, R L; Stottlemyre, J A; Smith, R P

    1980-07-01

    The objective of this experimental study was to determine how the mineralogical and physical characteristics of host rock formations are affected by environmental conditions anticipated for compressed air energy storage (CAES) in porous, permeable rock. In this study, Galesville sandstone cores were reacted in autoclave pressure vessels supporting one of four environments: dry air; heated, air-water vapor; heated, nitrogen-water vapor mixtures; and heated, compressed, liquid water. The simulated CAES environments were maintained in autoclave pressure vessels by controlling the following independent variables: temperature, pressure, time, oxygen content, carbon dioxide content, nitrogen content, and liquid volume. The dependent variables studied were: apparent porosity, gas permeability, water permeability, and friability. These variables were measured at ambient temperature and pressure before and after each sandstone sample was reacted in one of the CAES environments. The experiments gave the following results: the Galesville sandstone exhibited excellent stability in dry air at all temperatures tested (50/sup 0/ to 300/sup 0/C); and significant physical alterations occurred in sandstone samples exposed to liquid water above 150/sup 0/C. Samples shielded from dripping water exhibited excellent stability to 300/sup 0/C; sandstone may be a suitable storage media for heated, humid air provided elevated temperature zones are relatively free of mobile liquid water; and observed changes in the physical properties of the rock may have been caused, in part, by the lack of confining stress on the sample. The inability to apply confining pressure is a severe limitation of autoclave experiments.

  12. On nuclear reaction duration at the range of overlapping resonances

    International Nuclear Information System (INIS)

    Olkhovsky, V.S.

    1981-01-01

    Nuclear reaction duration above the threshold of overlapping resonances is investigated and its importance to obtain a new information on a collision mechanism is evidenced. It is shown also that the duration of resonant nuclear reactions is asymptotically decreasing according to the law[E 2 n(E)] -1 when the energy E and the number of open channels n(E) are increasing [ru

  13. Architecture of an Upper Jurassic barrier island sandstone reservoir, Danish Central Graben:

    DEFF Research Database (Denmark)

    Johannessen, Peter N.; Nielsen, Lars H.; Nielsen, Lars

    2010-01-01

    An unusually thick (c. 88 m), transgressive barrier island and shoreface sandstone succession characterizes the Upper Jurassic Heno Formation reservoir of the Freja oil field situated on the boundary of Denmark and Norway. The development and preservation of such thick transgressive barrier island...... sands is puzzling since a barrier island typically migrates landwards during transgression and only a thin succession of back-barrier and shoreface sands is preserved. Investigation of the development and geometry of the Freja reservoir sandstones is problematic since the reservoir is buried c. 5 km...... and seismic resolution is inadequate for architectural analysis. Description of the reservoir sandstone bodies is thus based on sedimentological interpretation and correlation of seven wells, of which five were cored. Palaeotopography played a major role in the position and preservation of the thick reservoir...

  14. Concurrent nitrate and Fe(III) reduction during anaerobic biodegradation of phenols in a sandstone aquifer

    DEFF Research Database (Denmark)

    Broholm, Mette; Crouzet, C.; Arvin, Erik

    2000-01-01

    The biodegradation of phenols (similar to 5, 60, 600 mg 1(-1)) under anaerobic conditions (nitrate enriched and unamended) was studied in laboratory microcosms with sandstone material and groundwater from within an anaerobic ammonium plume in an aquifer, The aqueous phase was sampled and analyzed...... for phenols and selected redox sensitive parameters on a regular basis. An experiment with sandstone material from specific depth intervals from a vertical profile across the ammonium plume was also conducted. The miniature microcosms used in this experiment were sacrificed for sampling for phenols...... and selected redox sensitive parameters at the end of the experiment. The sandstone material was characterized with respect to oxidation and reduction potential and Fe(II) and Fe(III) speciation prior to use for all microcosms and at the end of the experiments for selected microcosms. The redox conditions...

  15. Study of lixiviant damage of a sandstone deposit during in-situ leaching of uranium

    International Nuclear Information System (INIS)

    Liao Wensheng; Wang Limin; Jiang Yan; Jiang Guoping; Tan Yahui

    2014-01-01

    The permeability of sandstone deposit is a key factor for economical uranium recovery during in-situ leaching uranium. Low permeability sandstone uranium deposits behave low push-pull capacity, and show formation damage in leaching operations. It is important to study formation damage of permeability, therefore, and to stabilize even improve the push-pull power of drillholes during in-situ leaching. In this paper, formation damage caused by lixiviants was investigated based on a low permeability sandstone uranium deposit. The resulted showed that, under the conditions of in-situ leaching, the salinity of leaching fluid has no harm to formation permeability, on the contrary, the increment of salinity of lixiviant during in-situ leaching improve the permeability of the deposit. The alkalinity, hydrogen peroxide and productivity of the lixiviant cause no significant formation damage. But the fine particles in the lixiviant shows formation damage significantly, and the quantity of the particles should be controlled during production. (authors)

  16. Reviews on the metallogenic and geological features of sandstone-type uranium deposits in Japan

    International Nuclear Information System (INIS)

    Pei Chengkai; Huang Xianfang; Zhang Baoju

    2006-01-01

    Regional geologic settings of sandstone-type uranium deposits in Japan are firstly analyzed. The regional tectonic evolution characteristics of 'Green tuff region' and 'Non green tuff region' and their relationship with uranium mineralization are elaborated in depth. Based on those mentioned above, the uranium sources of sandstone-type uranium deposits in Japan are discussed deeply and the most favorable uranium sources are considered to come from the basement and the surrounding granites. Their intrusive epochs range from Later Cretaceous to Palaeogene (about 60 to 70 Ma ago). The characteristics of ore-bearing host rocks, matter compositions of the deposits, ore formation enrichment factors, the hydrogeologic conditions and so on are described by taking Ningyo-Toge and Tono deposits as examples. Finally, the prospecting measures for the palaeo-channel sandstone-type uranium deposits (basal type) are reviewed. (authors)

  17. Experimental and Numerical Investigations on Strength and Deformation Behavior of Cataclastic Sandstone

    Science.gov (United States)

    Zhang, Y.; Shao, J. F.; Xu, W. Y.; Zhao, H. B.; Wang, W.

    2015-05-01

    This work is devoted to characterization of the deformation and strength properties of cataclastic sandstones. Before conducting mechanical tests, the physical properties were first examined. These sandstones are characterized by a loose damaged microstructure and poorly cemented contacts. Then, a series of mechanical tests including hydrostatic, uniaxial, and triaxial compression tests were performed to study the mechanical strength and deformation of the sandstones. The results obtained show nonlinear stress-strain responses. The initial microcracks are closed at hydrostatic stress of 2.6 MPa, and the uniaxial compressive strength is about 0.98 MPa. Under triaxial compression, there is a clear transition from volumetric compressibility to dilatancy and a strong dependency on confining pressure. Based on the experimental evidence, an elastoplastic model is proposed using a linear yield function and a nonassociated plastic potential. There is good agreement between numerical results and experimental data.

  18. Possible application of underground leaching of uranium in ''sandstone'' deposits by drilling method

    International Nuclear Information System (INIS)

    Bareja, E.

    1988-01-01

    Underground leaching as the method for excavation of uranium from its sandstone deposits is applied in many countries. A preliminary examination of a possible use of this method to sandstone deposits in Poland suggests it to be analysed against the uranium mineralization, noted within sediments of the Lower Triassic age in the Peribaltic Syneclise in the Krynica Morska - Paslek area. Before a definite decision on such exploitation of uranium, geologic and hydrogeologic conditions should be studied of individual uranium-bearing beds, particularly their permeability and insulation by impermeable claystone series as well as extraction of uranium from its bearing sandstones. The depth at which uranium-bearing beds occur, forms a very important item. The depth at which uranium ores described in literature and exploited by this method occur, does not exceed 700 m. 7 refs. (author)

  19. The sedimentology of uranium-bearing sandstones on the farm Riet Kuil 307, Beaufort West area

    International Nuclear Information System (INIS)

    Cole, D.I.

    1980-10-01

    The sedimentology of four sandstones was studied in outcrop and in the subsurface on the farm Riet Kuil 307, near Beaufort West. Only two of these sandstones are mineralised. These are four surface and two subsurface uranium anomalies and one surface uranium anomaly. The sedimentological study was made by means of 47 vertical profiles measured across and adjacent to the surface anomalies as well as 11 core-logs, which intersected the subsurface anomalies. The unmineralised sandstones are included in this study. A total of 19 sedimentary facies was recognised within the fluvial sandstone sequence according to the criteria of grain-size and sedimentary structure. Transitions between the facies were subjected to a Markov chain analysis in order to delineate Markov-dependent transitions. Uranium mineralisation is almost entirely confined to the coarser-grained sedimentary facies, which probably acted as suitable aquifers for the transport of uraniferous solutions prior to the precipitation of the uranium. Horizontally bedded sandstone facies comprises 60 per cent of the total cumulative thickness of mineralisation. The nature of the bedding of this facies may have provided a more effective permeability zone for the transport of uraniferous solutions. This facies contains an abundance of carbonaceous material which acted as an important indirect reductant for the precipitation of uranium from solution. The direct reductant was most probably H 2 S produced by enaerobic bacteria acting on this carbonaceous material shortly after deposition of the sediments. Carbonaceous material also occurs in the other mineralised facies and is considered to be the major control on the mineralisation in the uranium-bearing sandstones

  20. Wettability of Chalk and Argillaceous Sandstones Assessed from T1/T2 Ratio

    DEFF Research Database (Denmark)

    Katika, Konstantina; Saidian, M.; Fabricius, Ida Lykke

    ratio can quantify the affinity between the rock and wetting pore fluid. The affinity is a measure directly linked to wettability. In order to investigate the T2-shortening, we performed T1-T2 NMR experiments on different samples of chalk, Berea sandstone, and chloritic greensand, saturated either...... with water, oil or oil/water at irreducible water saturation. The T1/T2 ratio obtained from T1-T2 maps reflects the T2-shortening. We compare the T1/T2 ratio for the same type of rock, saturated with different fluids. The chalk shows high affinity for water, Berea sandstone has no clear preference for oil...

  1. Ferroan dolomite cement in Cambrian sandstones: burial history and hydrocarbon generation of the Baltic sedimentary basin

    DEFF Research Database (Denmark)

    Sliaupa, S.; Cyziene, J.; Molenaar, Nicolaas

    2008-01-01

    The conditions and timing of carbonate cementation in Cambrian sandstones of the Baltic sedimentary basin were determined by oxygen and carbon stable isotope and chemical data in combination with optical and cathodoluminescence petrographic studies. Studied samples represent a range in present...... burial depth from 340 to 2150 m. The carbonate cement is dominantly ferroan dolomite that occurs as dispersed patches of poikilotopic crystals. Temperatures of dolomite precipitation, based on delta O-18 values, range from 27 degrees C in the shallow buried to 95 degrees C in the deep buried sandstones...

  2. Low field NMR surface relaxivity studies of chalk and argillaceous sandstones

    DEFF Research Database (Denmark)

    Katika, Konstantina; Fordsmand, Henrik; Fabricius, Ida Lykke

    2017-01-01

    the accuracy of predictions of petrophysical properties of various rocks with the use of NMR spectrometry. We perform laboratory transverse relaxation (T2) measurements on water saturated Gorm field chalk, Stevns Klint chalk, Solsort field greensand and Berea sandstone. These rocks are of particular interest...... field chalk and Solsort field greensand have higher ρ at higher Larmor frequency. By contrast, ρ of the purely calcitic Stevns chalk and quartzitic Berea sandstone proved not to be affected by the changes in frequency. T2 distributions at temperatures ranging from 10 °C to 60 °C provided comparison...

  3. INAA and petrological study of sandstones from Khmer temples in Angkor

    International Nuclear Information System (INIS)

    Kucera, J.; Kranda, K.; Novak, J.K.; Poncar, J.; Krausova, I.; Soukal, L.

    2009-01-01

    INAA was used to determine 35 major, minor and trace elements in sandstone samples taken from building blocks of 21 Khmer temples in Angkor, Cambodia. The sandstone samples were also characterized by conventional optical microscopy, X-ray diffraction analysis and electron microprobe analysis. The aim of this work was to examine the hypothesis that a particular elemental and/or mineral composition of the building materials can be characteristic of a particular architectural style/building period in the history of constructing the Angkor monuments. Preliminary results of this study are presented

  4. The effects of impure CO2 on reservoir sandstones: results from mineralogical and geomechanical experiments

    Science.gov (United States)

    Marbler, H.; Erickson, K. P.; Schmidt, M.; Lempp, Ch.; Pöllmann, H.

    2012-04-01

    An experimental study of the behaviour of reservoir sandstones from deep saline aquifers during the injection and geological storage of CO2 with the inherent impurities SOX and NOX is part of the German national project COORAL*. Sample materials were taken from outcrops of possible reservoir formations of Rotliegend and Bunter Sandstones from the North German Basin. A combination of mineralogical alteration experiments and geomechanical tests was carried out on these rocks to study the potential effects of the impurities within the CO2 pore fluid. Altered rock samples after the treatment with CO2 + SOX/NOX in an autoclave system were loaded in a triaxial cell under in-situ pressure and temperature conditions in order to estimate the modifications of the geomechanical rock properties. Mineralogical alterations were observed within the sandstones after the exposure to impure supercritical (sc)CO2 and brine, mainly of the carbonatic, but also of the silicatic cements, as well as of single minerals. Besides the partial solution effects also secondary carbonate and minor silicate mineral precipitates were observed within the pore space of the treated sandstones. These alterations affect the grain structure of the reservoir rock. Results of geomechanical experiments with unaltered sandstones show that the rock strength is influenced by the degree of rock saturation before the experiment and the chemical composition of the pore fluid (scCO2 + SOX + NOX). After long-term autoclave treatment with impure scCO2, the sandstone samples exhibit modified strength parameters and elastic deformation behaviour as well as changes in porosity compared to untreated samples. Furthermore, the injected fluid volume into the pore space of sandstones from the same lithotype varies during triaxial loading depending on the chemistry of the pore fluid. CO2 with NOX and SOX bearing fluid fills a significantly larger proportion of the sandstone pore space than brine with pure scCO2. * The

  5. Thermophysical behavior of St. Peter sandstone: application to compressed air energy storage in an aquifer

    Energy Technology Data Exchange (ETDEWEB)

    Erikson, R.L.

    1983-12-01

    The long-term stability of a sandstone reservoir is of primary importance to the success of compressed air energy storage (CAES) in aquifers. The purpose of this study was to: develop experimental techniques for the operation of the CAES Porous Media Flow Loop (PMFL), an apparatus designed to study the stability of porous media in subsurface geologic environments, conduct experiments in the PMFL designed to determine the effects of temperature, stress, and humidity on the stability of candidate CAES reservoir materials, provide support for the CAES field demonstration project in Pittsfield, Illinois, by characterizing the thermophysical stability of Pittsfield reservoir sandstone under simulated field conditions.

  6. The controlling role of positive structures over the metallogenesis and emplacement of inter layer oxidation sandstone type uranium deposits

    International Nuclear Information System (INIS)

    Gu Kangheng; Chen Zuyi

    2010-01-01

    The positive structures in this paper mean the geological structures related to the occurrence of U-metallogenic zones or U-deposit such as anticlines, uplifts and uplifted fault-blocks. Occurrence features of interlayer oxidation sandstone type deposit at the southern margin of Yili basin and southwestern margin of Turpan-Hami basin, the northeastern margin of Jiudong basin illustrate that the sandstone-hosted uranium deposits, the U-mineralized sections and the uranium occurrences are always selectively emplaced on/in positive structures. The reasons for this lie in the formation mechanism of sandstone-hosted U-deposits. The positive structures raised the elevation of ore-hosting sandstone horizon and make it close to ground surface or exposed at the ground surface, which result in the infiltration of uranium and oxygen bearing groundwater from recharge area into host sandstone horizon, and the interlayer oxidation of host sandstone, as well as the dissolution and the migration of uranium in host sandstone, and the reduction mineralization at the oxidation-reduction interface. Sufficient attention should be paid to the controlling role of positive structures over the metallogenesis and emplacement of sandstone-hosted uranium deposits. They could act as an important criterion for recognizing and prognosticating potential uranium mineralized areas in uranium metallogenic zones or uranium-productive sedimentary basins. (authors)

  7. Permeability model of tight reservoir sandstones combining core-plug and miniperm analysis of drillcore; longyearbyen co2lab, Svalbard

    NARCIS (Netherlands)

    Magnabosco, Cara; Braathen, Alvar; Ogata, Kei

    2014-01-01

    Permeability measurements in Mesozoic, low-permeability sandstone units within the strata cored in seven drillholes near Longyearbyen, Svalbard, have been analysed to assess the presence of aquifers and their potentials as reservoirs for the storage of carbon dioxide. These targeted sandstones are

  8. Lack of inhibiting effect of oil emplacement on quartz cementation: Evidence from Cambrian reservoir sandstones, Paleozoic Baltic Basin

    DEFF Research Database (Denmark)

    Molenaar, Nicolaas; Cyziene, Jolanta; Sliaupa, Saulius

    2008-01-01

    Currently, the question of whether or not the presence of oil in sandstone inhibits quartz cementation and preserves porosity is still debated. Data from a number of Cambrian sandstone oil fields and dry fields have been studied to determine the effects of oil emplacement on quartz cementation. T...

  9. The Upper Permian sandstones of Mountains Mecsek: form elements of uranium ore mineralization and facies relations Pt. 2

    International Nuclear Information System (INIS)

    Vincze, Janos; Somogyi, Janos

    1984-01-01

    The ore mineralization in the Upper Permian sandstones of Mountais Mecsek, Hungary, was brought about at the oxidation-reduction front between the grey and red sandstones; the predominant rock colour here is green. The sandstones of different colour are oxidation-reduction species. The formation is a megacycle containing in its core grey sandstones of reduced state with coalified plant remains and in its mantle oxidized red sandstones. Uranium accumulates mainly in the transitional green facies. Uranium content gets enriched to a commercial concentration only if the difference in potential of neighbouring beds is in the range of 400-480 mV. The relationship between organic matter and uranium content in the individual facies is shown. The principles of oxidation-reduction processes in the formation of boundary facies are discussed. (V.N.)

  10. Study on U-Ra equilibrium coefficient of the in-situ leaching sandstone-type uranium deposits: A case study of Qianjiadian uranium deposit

    International Nuclear Information System (INIS)

    Xia Yuliang; Xiu Qunye; Han Jun; Li Linqiang; Zheng Jiwei

    2013-01-01

    This paper investigated the U-Ra equilibrium coefficient (K-p) of mineralized sandstone and mudstone, and unmineralized sandstone and mudstone for the in-situ leaching sandstone-type uranium deposits. It is surprised that all of the mineralized sandstone and mudstone are both relatively to be partial to uranium, but all of the unmineralized sandstone and mudstone are both relatively to be partial to radium. Meanwhile the uranium in mineralized mudstone is relatively richer than that in mineralized sandstone, and the radium in unmineralized mudstone is relatively richer than that in unmineralized sandstone. It is suggested that mudstones were permeable at the uranium mineralized phase and the unmineralized mudstone and sandstone could serve as important mineralized uranium source. (authors)

  11. Early cretaceous Obernirchen and Bentheim sandstones from Germany used as dimension stone in the Netherlands: geology physical properties, architectural use and comparative weathering

    NARCIS (Netherlands)

    Dubelaar, C.W.; Nijland, T.G.

    2015-01-01

    The Netherlands, with only scarce occurrences of outcropping or shallow buried natural stone, has over centuries imported huge quantities of Early Cretaceous Bentheim Sandstone and Obernkirchen Sandstone from Germany. The present paper provides an overview of their distribution and properties

  12. Synthesizing controllers from duration calculus

    DEFF Research Database (Denmark)

    Fränzle, Martin

    1996-01-01

    Duration Calculus is a logic for reasoning about requirements for real-time systems at a high level of abstraction from operational detail, which qualifies it as an interesting starting point for embedded controller design. Such a design activity is generally thought to aim at a control device...... the physical behaviours of which satisfy the requirements formula, i.e. the refinement relation between requirements and implementations is taken to be trajectory inclusion. Due to the abstractness of the vocabulary of Duration Calculus, trajectory inclusion between control requirements and controller designs...... for embedded controller design and exploit this fact for developing an automatic procedure for controller synthesis from specifications formalized in Duration Calculus. As far as we know, this is the first positive result concerning feasibility of automatic synthesis from dense-time Duration Calculus....

  13. Prediction of calcite Cement Distribution in Shallow Marine Sandstone Reservoirs using Seismic Data

    Energy Technology Data Exchange (ETDEWEB)

    Bakke, N.E.

    1996-12-31

    This doctoral thesis investigates how calcite cemented layers can be detected by reflection seismic data and how seismic data combined with other methods can be used to predict lateral variation in calcite cementation in shallow marine sandstone reservoirs. Focus is on the geophysical aspects. Sequence stratigraphy and stochastic modelling aspects are only covered superficially. Possible sources of calcite in shallow marine sandstone are grouped into internal and external sources depending on their location relative to the presently cemented rock. Well data and seismic data from the Troll Field in the Norwegian North Sea have been analysed. Tuning amplitudes from stacks of thin calcite cemented layers are analysed. Tuning effects are constructive or destructive interference of pulses resulting from two or more closely spaced reflectors. The zero-offset tuning amplitude is shown to depend on calcite content in the stack and vertical stack size. The relationship is found by regression analysis based on extensive seismic modelling. The results are used to predict calcite distribution in a synthetic and a real data example. It is found that describing calcite cemented beds in shallow marine sandstone reservoirs is not a deterministic problem. Hence seismic inversion and sequence stratigraphy interpretation of well data have been combined in a probabilistic approach to produce models of calcite cemented barriers constrained by a maximum amount of information. It is concluded that seismic data can provide valuable information on distribution of calcite cemented beds in reservoirs where the background sandstones are relatively homogeneous. 63 refs., 78 figs., 10 tabs.

  14. Gravity-induced stress as a factor reducing decay of sandstone monuments in Petra, Jordan

    Czech Academy of Sciences Publication Activity Database

    Řihošek, J.; Bruthans, J.; Mašín, D.; Filippi, Michal; Carling, G. T.; Schweigstillová, Jana

    2016-01-01

    Roč. 19, 1 May (2016), s. 415-425 ISSN 1296-2074 R&D Projects: GA ČR GA13-28040S Institutional support: RVO:67985831 ; RVO:67985891 Keywords : Decay * Petra * sandstone monument * stability * stress Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.838, year: 2016

  15. Spherical and ellipsoidal cavities in European sandstones: a product of sinking carbonate dissolution front

    Czech Academy of Sciences Publication Activity Database

    Adamovič, Jiří; Mikuláš, Radek; Navrátil, Tomáš

    2015-01-01

    Roč. 59, Supplement 1 (2015), s. 123-149 ISSN 0372-8854 R&D Projects: GA AV ČR IAA300130806; GA ČR GA13-28040S Institutional support: RVO:67985831 Keywords : symmetrical cavities * solutional landforms * cavernous weathering * tafoni * sandstone * concretions * carbonate dissolution front Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.103, year: 2015

  16. Prospect analysis for sandstone-type uranium mineralization in the northern margin of Qaidam basin

    International Nuclear Information System (INIS)

    Liu Lin; Song Xiansheng; Feng Wei; Song Zhe; Li Wei

    2010-01-01

    Affected by the regional geological structural evolution, a set of sedimentary structure, i.e. the construction of coal-bearing classic rocks which is in favor of the sandstone-type uranium mineralization has deposited in the northern margin of Qaidam Basin since Meso-Cenozoic. A NWW thrust nappe tectonic belt, i.e. the ancient tectonic belt which is the basis for the development of ancient interlayer oxidation zone formed by the tectonic reverse in late Jurassic and Cretaceous. The Mid and late Jurassic layer was buried by the weak extension in Paleogene and the depression in early Neogene. The extrusion reversal from late Neogene to Quaternary made the basin into the development era of the modern interlayer oxidation zone. It can be concluded that the layer of the northern margin of Qaidam Basin has the premise for the formation of sandstone-type uranium ore. Based on the analysis of the characteristics of the thrust belt, the structure of the purpose layer, the sand body, the hydrogeology, the interlayer oxidation zone and uranium mineralization, the results indicated that the ancient interlayer oxidation zone is the prospecting type of sandstone-type uranium ore. Beidatan and the east of Yuqia are the favorable prospective area of sandstone-type uranium mineralization. (authors)

  17. Application research on remote sensing geology of sandstone-type uranium deposit in Yili basin

    International Nuclear Information System (INIS)

    Wang Huaiwu

    2002-01-01

    Based on remote sensing images and practical materials, and new ideas of laying particular emphasis on the research of regional geologic structures, and large in-situ leachable sandstone-type uranium deposits, applying the theory of plate tectonics, the author makes a comprehensive analysis on the uranium metallogenic environments, characteristics of regional geologic structures, the ore-controlling mechanism and factors, and uranium metallogeny. Authors propose that large interlayer oxidation zone sandstone-type uranium deposits are controlled by the combination of the stable block in Meso-Cenozoic compressive-shearing faulted subsided basin on the Yili multiphase massif in Tianshan paleo-island arc system, and the specific paleo-geographic environments and its' structural terrace'. The origin of hydrogenic sandstone-type uranium deposits is summarized by the authors as the 'mixing and neutralization' genetic model, and the 'eight ore-controlling factors merge into an organic whole' prospecting model. The above mentioned provides clear prospecting direction and new ideas for the forecasting direction for prospecting large sandstone-type uranium deposits

  18. A new biostratigraphical tool for reservoir characterisation and well correlation in permo-carboniferous sandstones

    NARCIS (Netherlands)

    Garming, J.F.L.; Cremer, H.; Verreussel, R.M.C.H.; Guasti, E.; Abbink, O.A.

    2010-01-01

    Permo-Carboniferous sandstones are important reservoir rocks for natural gas in the Southern North Sea basin. This is a mature area which makes tools for reservoir characterization and well to well correlation important for field optimalisation and ongoing exploration activities. Within the

  19. Recent Atmospheric Deposition and its Effects on Sandstone Cliffs in Bohemian Switzerland National Park, Czech Republic

    Czech Academy of Sciences Publication Activity Database

    Vařilová, Z.; Navrátil, Tomáš; Dobešová, Irena

    2011-01-01

    Roč. 220, 1/4 (2011), s. 117-130 ISSN 0049-6979 Institutional research plan: CEZ:AV0Z30130516 Keywords : acid deposition * sandstone percolates * chemical weathering * salt efflorescence * Black Triangle * aluminum * sulfates Subject RIV: DD - Geochemistry Impact factor: 1.625, year: 2011

  20. Sensibility test for uranium ores from Qianjiadian sandstone type uranium deposit

    International Nuclear Information System (INIS)

    Zhang Mingyu

    2005-01-01

    Sensibility tests for uranium ores from Qianjiadian sandstone type uranium deposit in Songliao Basin which is suitable to in-situ leach are carried out, including water sensibility, velocity sensibility, salt sensibility, acid sensibility and alkaline sensibility. The sensibility critical value of this ore is determined. Some references on mining process and technical parameter are provided for in-situ leaching of uranium. (authors)

  1. Combined rock-physical modelling and seismic inversion techniques for characterisation of stacked sandstone reservoir

    NARCIS (Netherlands)

    Justiniano, A.; Jaya, Y.; Diephuis, G.; Veenhof, R.; Pringle, T.

    2015-01-01

    The objective of the study is to characterise the Triassic massive stacked sandstone deposits of the Main Buntsandstein Subgroup at Block Q16 located in the West Netherlands Basin. The characterisation was carried out through combining rock-physics modelling and seismic inversion techniques. The

  2. Structure and fluid evolution of Yili basin and their relation to sandstone type uranium mineralization

    International Nuclear Information System (INIS)

    Wang Juntang; Wang Chengwei; Feng Shirong

    2008-01-01

    Based on the summary of strata and structure distribution of Yili basin, the relation of structure and fluid evolution to sandstone type ur alum mineraliation are analyzed. It is found that uranium mineralization in Yili basin experienced ore hosting space forming, pre-alteration of hosting space, hosting space alteration and uranium formation stages. (authors)

  3. Aeromagnetic gradient survey and elementary application in sandstone type uranium deposits prospecting

    International Nuclear Information System (INIS)

    Li Xiaolu; Chang Shushuai

    2009-01-01

    The principle,advantage and data processing of aeromagnetic gradient survey approach is introduced in this paper, and used to identify the shallow surface faults, uranium ore-forming environment and depth of magnetic body for the prospecting of sandstone type uranium deposits. (authors)

  4. An Effective Acid Combination for Enhanced Properties and Corrosion Control of Acidizing Sandstone Formation

    International Nuclear Information System (INIS)

    Shafiq, Mian Umer; Mahmud, Hisham Khaled Ben

    2016-01-01

    To fulfill the demand of the world energy, more technologies to enhance the recovery of oil production are being developed. Sandstone acidizing has been introduced and it acts as one of the important means to increase oil and gas production. Sandstone acidizing operation generally uses acids, which create or enlarge the flow channels of formation around the wellbore. In sandstone matrix acidizing, acids are injected into the formation at a pressure below the formation fracturing pressure, in which the injected acids react with mineral particles that may restrict the flow of hydrocarbons. Most common combination is Hydrofluoric Acid - Hydrochloric with concentration (3% HF - 12% HCl) known as mud acid. But there are some problems associated with the use of mud acid i.e., corrosion, precipitation. In this paper several new combinations of acids were experimentally screened to identify the most effective combination. The combinations used consist of fluoboric, phosphoric, formic and hydrofluoric acids. Cores were allowed to react with these combinations and results are compared with the mud acid. The parameters, which are analyzed, are Improved Permeability Ratio, strength and mineralogy. The analysis showed that the new acid combination has the potential to be used in sandstone acidizing. (paper)

  5. Palaeoclimatic trends deduced from the hydrochemistry of a Triassic sandstone aquifer, U.K

    International Nuclear Information System (INIS)

    Bath, A.H.; Edmunds, W.M.; Andrews, J.N.

    1978-01-01

    A detailed geochemical study (elemental, isotopic and dissolved inert gases) of unconfined and confined sections of the Triassic non-marine sandstone aquifer in Eastern England has been undertaken. Aspects of the recharge history of this aquifer over the past 40 000 years are revealed by examination of the data. (orig./HK) [de

  6. Origin of brackish groundwater in a sandstone aquifer on Bornholm, Denmark

    DEFF Research Database (Denmark)

    Jørgensen, Niels Oluf; Heinemeier, Jan

    2008-01-01

    A multi-isotope approach in combination with hydrochemical data and borehole logging is applied to identify the source of brackish groundwater in a borehole in the well field of Neksø Municipal Waterworks in Bornholm, Denmark. The aquifer lithology consists of fractured Lower Cambrian sandstones...

  7. Numerical simulation of roadway support in a sandstone-type uranium mine

    International Nuclear Information System (INIS)

    Liu Huipeng; Li Yu; Song Lixia

    2009-01-01

    At present, the most surrounding rocks of sandstone-type uranium mines in China are mudstone, sandstone, pelitic siltstone, and so on. They show the characteristics of soft rock. Such uranium deposit is not fit for in-situ leaching. If the uranium ores are mined by conventional mining method, one of the problems to be solved is the support technique in the soft rock roadway. So, taking a uranium mine in Inner Mongolia as the research object, the support technique in the soft rock roadway of the sandstone-type uranium deposits is studied. Through on-site engineering geological investigation and laboratory test, the main reasons for roadway damage are analyzed. A technique of support in the soft rock roadway of sandstone-type uranium deposits is put forward by drawing on the expericnce of soft rock roadway support in coal mines. The roadway shape and support parameters are optimized by using a numerical simulation method. The results verified the feasibility of the supporting technique. (authors)

  8. Mechanical Behavior of Red Sandstone under Incremental Uniaxial Cyclical Compressive and Tensile Loading

    Directory of Open Access Journals (Sweden)

    Baoyun Zhao

    2017-01-01

    Full Text Available Uniaxial experiments were carried out on red sandstone specimens to investigate their short-term and creep mechanical behavior under incremental cyclic compressive and tensile loading. First, based on the results of short-term uniaxial incremental cyclic compressive and tensile loading experiments, deformation characteristics and energy dissipation were analyzed. The results show that the stress-strain curve of red sandstone has an obvious memory effect in the compressive and tensile loading stages. The strains at peak stresses and residual strains increase with the cycle number. Energy dissipation, defined as the area of the hysteresis loop in the stress-strain curves, increases nearly in a power function with the cycle number. Creep test of the red sandstone was also conducted. Results show that the creep curve under each compressive or tensile stress level can be divided into decay and steady stages, which cannot be described by the conventional Burgers model. Therefore, an improved Burgers creep model of rock material is constructed through viscoplastic mechanics, which agrees very well with the experimental results and can describe the creep behavior of red sandstone better than the Burgers creep model.

  9. Geology and potential of the formation of sandstone type uranium mineralization at Hatapang region, North Sumatera

    International Nuclear Information System (INIS)

    Ngadenin

    2013-01-01

    The Study based on geological setting of Hatapang region, North Sumatera, identified as a favourable area to the formation of sandstone type uranium mineralization. This characterized by the occurred of anomalous radioactivity, uranium contents of the upper cretaceous granite intrusions and radioactivity anomalous of tertiary sedimentary rocks deposited in terrestrial environments. The study is objective to find out the potential formation of sandstone type-uranium mineralization within tertiary sedimentary rocks based on data’s studies of geological, geochemical, mineralogy, radioactivity of rocks. Stratigraphy of Hatapang area of the oldest to youngest are quartz units (permian-carboniferous), sandstone units (upper Triassic), granite (upper cretaceous), conglomerate units (Lower –middle Miocene) and tuff units (Pleistocene). Hatapang’s granite is S type granite which is not only potential as source of radioactive minerals, particularly placer type monazite, but also potential as source rocks of sandstone type-uranium mineralization on lighter sedimentary rocks. Sedimentary rock of conglomerate units has potential as host rock, even though uranium did not accumulated in its rocks since the lack number of carbon as precipitant material and dissolved U"+"6 in water did not reduced into U"+"4 caused the uranium mineralization did not deposited. (author)

  10. The effect of grain size and cement content on index properties of weakly solidified artificial sandstones

    Science.gov (United States)

    Atapour, Hadi; Mortazavi, Ali

    2018-04-01

    The effects of textural characteristics, especially grain size, on index properties of weakly solidified artificial sandstones are studied. For this purpose, a relatively large number of laboratory tests were carried out on artificial sandstones that were produced in the laboratory. The prepared samples represent fifteen sandstone types consisting of five different median grain sizes and three different cement contents. Indices rock properties including effective porosity, bulk density, point load strength index, and Schmidt hammer values (SHVs) were determined. Experimental results showed that the grain size has significant effects on index properties of weakly solidified sandstones. The porosity of samples is inversely related to the grain size and decreases linearly as grain size increases. While a direct relationship was observed between grain size and dry bulk density, as bulk density increased with increasing median grain size. Furthermore, it was observed that the point load strength index and SHV of samples increased as a result of grain size increase. These observations are indirectly related to the porosity decrease as a function of median grain size.

  11. Method for the determination of clay and mica concentrations in subsurface sandstone formations through radioactive logging

    International Nuclear Information System (INIS)

    Allen, L.S.

    1984-01-01

    A method is described for radioactivity well logging in a subsurface sandstone formation penetrated by a borehole. The invention relates particularly to clay and mica contents, which are determined from the natural gamma-ray activities. The natural sources of gamma radiation in the formation, are the trace elements thorium, uranium and potassium. (U.K.)

  12. The effectiveness of starting the developement of lenticular sandstone and siltstone

    Energy Technology Data Exchange (ETDEWEB)

    Oshitki, V M; Khmelevskiy, Y I; Kolesnkikova, S A; Musin, M M; Sukhanov, N A

    1980-01-01

    Studies the determination of the effectiveness of working reserves for several typical cases of implementing development of collector-sandstone and siltstonee lenses. Shows that Siltstones require the use of amore rapid development system: with a ratio of injection to working wells of at least 1:3.

  13. Study on integrated evaluation of sandstone-hosted uranium metallogenic potential in southern Yili basin

    International Nuclear Information System (INIS)

    Han Shaoyang; Ke Dan; Xu Jianguo; Zheng Enjiu; Li Shengxiang

    2008-01-01

    Plenty of geological data have been accumulated during mineral resource survey in China; under the guidance of new metallogenic theories, it is an important task of how to use these data most effectively for the new cycle uranium survey. In this paper, the flow of establishing the integrated mineral deposits prospecting model for sandstone-hosted uranium deposits is put forward. Based on studying geologic, hydrogeologic and regional geophysical field characteristics of representative uranium deposits No. 512 in southern Yili basin, its multi-source information descriptive model has been established, from which 512-type integrated prospecting models of sandstone-hosted uranium orefield and deposits are summarized. According to the established integrated prospecting models, the metallogenic information extraction of sandstone-hosted uranium deposits has completed in the study area. Finally, the integrated quantitative evaluation of sandstone-hosted uranium metallogenic potential is performed by using the evidence weighing method to integrate middle scale multi-source metallogenic information in the southern Yili basin, and good prediction effect is obtained. (authors)

  14. Carbon dioxide/brine wettability of porous sandstone versus solid quartz: An experimental and theoretical investigation.

    Science.gov (United States)

    Alnili, Firas; Al-Yaseri, Ahmed; Roshan, Hamid; Rahman, Taufiq; Verall, Michael; Lebedev, Maxim; Sarmadivaleh, Mohammad; Iglauer, Stefan; Barifcani, Ahmed

    2018-08-15

    Wettability plays an important role in underground geological storage of carbon dioxide because the fluid flow and distribution mechanism within porous media is controlled by this phenomenon. CO 2 pressure, temperature, brine composition, and mineral type have significant effects on wettability. Despite past research on this subject, the factors that control the wettability variation for CO 2 /water/minerals, particularly the effects of pores in the porous substrate on the contact angle at different pressures, temperatures, and salinities, as well as the physical processes involved are not fully understood. We measured the contact angle of deionised water and brine/CO 2 /porous sandstone samples at different pressures, temperatures, and salinities. Then, we compared the results with those of pure quartz. Finally, we developed a physical model to explain the observed phenomena. The measured contact angle of sandstone was systematically greater than that of pure quartz because of the pores present in sandstone. Moreover, the effect of pressure and temperature on the contact angle of sandstone was similar to that of pure quartz. The results showed that the contact angle increases with increase in temperature and pressure and decreases with increase in salinity. Copyright © 2018 Elsevier Inc. All rights reserved.

  15. Effect of modified ethylsilicate consolidants on the mechanical properties of sandstone

    Czech Academy of Sciences Publication Activity Database

    Remzová, Monika; Šašek, Petr; Frankeová, Dita; Slížková, Zuzana; Rathouský, Jiří

    2016-01-01

    Roč. 112, JUN 2016 (2016), s. 674-681 ISSN 0950-0618 R&D Projects: GA MK(CZ) DF11P01OVV012 Keywords : sandstones * ethylsilicate consolidant * sol-gel process Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.169, year: 2016

  16. Recent exploration progresses on sandstone-hosted uranium deposits in north-western China

    International Nuclear Information System (INIS)

    Li, Z.

    2014-01-01

    The metallogenic target selection using multiple exploration techniques and drilling program for sandstone-hosted uranium deposits have been intensively carried out for recent years, and big progresses on new discoveries of uranium reserve/resource have been made in the Mesozoic sedimentary basins such as in Yili, Ordos etc. in North-western China The Yili basin is a depression one within the Tianshan Mountain belt in the western part of China. Its basement is composed of Proterozoic-Paleozoic metamorphic and sedimentary rocks, and covers of Mesozoic sediments. The early-middle Jurassic Shuixigou Group is major uranium-productive beds which are composed of three Formations such as Badaowan, Sangonghe, Xisanyao and eight sedimentary cycles. Uranium deposits are found in the south margin of the Basin and controlled by the redox zone. The combined exploration techniques of detailed sedimentary facies study, Rn-survey, high-precision magnetic and soil geochemical and seismic surveys have been successfully used to have locate the potential targets and mineralization zones. The enlargement of uranium reserve/resources in the known deposits and new resources in the selected new targets and cycles have been achieved through further drilling programs. The Ordos basin is a large Meso-Cenozoic basin developed in North China Platform, with its size of approximately 250,000 km"2 and is well known as an important “energy resources basin” because of abundance of coal, oil and gas deposits. The Dongsheng sandstone type uranium deposit is a large one discovered in recent years in northeastern Ordos basin. It is a special kind of sandstone type uranium deposit, different from other ordinary sandstone type deposits because of its unique signatures. It is generally controlled by a transitional zone between greenish and grayish sandstones, both of those two kinds of sandstones now indicate reduced geochemical environments. The greenish color of the paleooxidized sandstones mainly

  17. Detrital zircons from samples of five Neo proterozoic sandstone units deposited on Uruguay and Argentina: about evolution of paleographic Rio de la Plata craton

    International Nuclear Information System (INIS)

    Gaucher, C.; Poire, D.G.; Pamoukaghlian, K.; Gomez Peral, L.; Finney, S.; Valencia, V.; Blanco, G.

    2007-01-01

    We report U-Pb ages of detrital zircons from samples of five Neoproterozoic sandstone units deposited on the Rio de la Plata Craton (RPC) in Uruguay and Argentina. Quartz-arenites of the Piedras de Afilar Formation show typical Transamazonian ages, with peaks at 2.00-2.07, 1.87 and 1.78 Ga. However, the most important zircon population is Mesoproterozoic, showing maxima at 1.49, 1.35, 1.25 and 1.0 Ga. Zircons recovered from two sandstone levels in the Arroyo del Soldado Group (Yerbal and Cerros San Francisco formations) are mostly Archean in age, with maxima at 3.2 and 2.7 Ga. Palaeoproterozoic zircons are also prominent in this unit, with peaks at 2.45 and 2.18, with the latter a typical Transamazonian age. Two samples from the Sierras Bayas Group in Tandilia (Argentina) show different age spectra. Sandstones of the Villa Monica Formation show a unimodal zircon population of Transamazonian age (peak at 2.13 Ga). Sandstones of the Cerro Largo Formation are characterized by a dominant Transamazonian zircon population (peaks at 2.15, 2.0 and 1.79), but also important Archean-lowermost Palaeoproterozoic (3.33, 2.99, 2.7, 2.47 Ga) and Mesoproterozoic peaks (1.55, 1.23 and 1.06). The abundance of Mesoproterozoic detrital zircons is surprising. A proto-Andean, Mesoproterozoic belt is suggested as the source of the Mesoproterozoic detritus. Archean rocks of the RPC crop out only in the Nico Perez Terrane in Uruguay, suggesting that the Nico Perez Terrane was much closer to Tandilia than it is today. The sinistral reactivation of the Sarandi del Yi Shear Zone in the Cambrian, as a result of tangential collision of the Cuchilla Dionisio-Pelotas Terrane, may explain this observations. The absence of Neoproterozoic zircons shows that the studied units were deposited in a stable continental margin opening to the East and South. These Neoproterozoic basins had obviously no contribution whatsoever from Brasiliano-Pan African belts, supporting the idea of Cambrian terrane

  18. The effect of the pore-fluid factor on strength and failure mechanism of Wilkeson sandstone

    Science.gov (United States)

    Kätker, A. K.; Rempe, M.; Renner, J.

    2016-12-01

    The effective stress law, σn,eff = σn - αpf, is a central tool in analysing phenomena related to hydromechanical coupling, such as fluid-induced seismicity or aftershock activity. The effective-stress coefficient α assumes different values for specific physical properties and may deviate from 1. The limited number of studies suggest that brittle compressive strength obeys an effective-stress law when effective drainage is achieved. Yet, open questions remain regarding, e.g., the role of the loading path. We performed suites of triaxial compression tests on samples of Wilkeson sandstone at a range of pore-fluid pressures but identical effective confining pressure (60, 100, and 120 MPa) maintaining the pore-fluid factor λ = pf / pc constant (0.05, 0.2, 0.4, 0.55) during the isostatic loading stage to ensure uniform loading paths. Samples were shortened with a strain rate of 4×10-7 s-1 yielding drained conditions. All tests were terminated at a total axial strain of 4.5% for comparability of microstructures. The tests also included continuous permeability determination and ultrasonic p-wave-velocity measurements to monitor microstructural evolution. Results from experiments conducted at peff = 100 MPa show that dry samples exhibit a higher peak strength and brittle failure while water-saturated samples tend to deform at lower stress by cataclastic flow indicating physico-chemical weakening. Regardless of pore-fluid factor, the saturated experiments exhibit similar peak and residual strength. Differences in failure mechanism (degree of macroscopic localization) and volumetric strain evolution are however noticed, albeit without systematic relation to pore-fluid factor. Microstructure analyses by optical and scanning electron microscopy revealed an evolution from localized shear zones in dry experiments and experiments with a low pore-fluid factor to rather distributed cataclastic flow for experiments with high pore fluid factors. Yet, mechanical and structural

  19. Analysis of single oil-bearing fluid inclusions in mid-Proterozoic sandstones (Roper Group, Australia)

    Science.gov (United States)

    Siljeström, Sandra; Volk, Herbert; George, Simon C.; Lausmaa, Jukka; Sjövall, Peter; Dutkiewicz, Adriana; Hode, Tomas

    2013-12-01

    Hydrocarbons and organic biomarkers extracted from black shales and other carbonaceous sedimentary rocks are valuable sources of information on the biodiversity and environment of early Earth. However, many Precambrian hydrocarbons including biomarkers are suspected of being younger contamination. An alternative approach is to study biomarkers trapped in oil-bearing fluid inclusions by bulk crushing samples and subsequently analysing the extracted hydrocarbons with gas chromatography-mass spectrometry. However, this method does not constrain the hydrocarbons to one particular oil inclusion, which means that if several different generations of oil inclusions are present in the sample, a mix of the content from these oil inclusions will be analysed. In addition, samples with few and/or small inclusions are often below the detection limit. Recently, we showed that it is possible to detect organic biomarkers in single oil-bearing fluid inclusions using time-of-flight secondary ion mass spectrometry (ToF-SIMS). In the present study, single fluid inclusion analysis has been performed on Proterozoic samples for the first time. Four individual oil-bearing fluid inclusions, found in 1430 Ma sandstone from the Roper Superbasin in Northern Australia, were analysed with ToF-SIMS. The ToF-SIMS spectra of the oil in the different inclusions are very similar to each other and are consistent with the presence of n-alkanes/branched alkanes, monocyclic alkanes, bicyclic alkanes, aromatic hydrocarbons, and tetracyclic and pentacyclic hydrocarbons. These results are in agreement with those obtained from bulk crushing of inclusions trapped in the same samples. The capability to analyse the hydrocarbon and biomarker composition of single oil-bearing fluid inclusions is a major breakthrough, as it opens up a way of obtaining molecular compositional data on ancient oils without the ambiguity of the origin of these hydrocarbons. Additionally, this finding suggests that it will be possible

  20. Investigated Miscible CO2 Flooding for Enhancing Oil Recovery in Wettability Altered Chalk and Sandstone Rocks

    Energy Technology Data Exchange (ETDEWEB)

    Tabrizy, Vahid Alipour

    2012-07-01

    The thesis addresses oil recovery by miscible CO2 flooding from modified sandstone and chalk rocks. Calcite mineral surface is modified with stearic acid (SA) and asphaltene, and the silicate mineral surfaces are modified with N,N-dimethyldodecylamine (NN-DMDA) and asphaltene. The stability of adsorbed polar components in presence of SO4 2- and Mg2 + ions is also investigated. Recovery from sandstone cores is consistently lower than that from chalk cores saturated with the same oil and flooded with CO2 at all miscible flooding conditions. This may be due to the larger permeability contrasts in sandstone cores, which promote the fingering phenomenon. Miscible CO2 flooding for chalk and sandstone cores with distilled water, as initial water saturation, shows also lower oil recovery than cores saturated with different ions. At higher miscible flooding conditions, higher oil recovery is obtained. However, presence of light components (such as C1 or C3) in oil reduced the recovery. Oil recovery in presence of methane (C1) is lower than that in presence of methane and propane (C1/C3). A ternary diagram was constructed in order to understand the CO2 flooding mechanism(s) at the different flooding conditions and in presence of light components. The side effect of the flooding with CO2 is the probability for asphaltene deposition. An approach based on solubility parameter in the liquid, is used to assess the risk for asphaltene deposition during CO2 miscible flooding. The light components (C1/C3) and higher flooding conditions enhanced the risk for asphaltene instability. It is also shown higher amount of asphaltene deposition in chalk cores than that in sandstone cores at similar miscibility conditions.(au)

  1. Desert and groundwater dynamics of the Jurassic Navajo Sandstone, southeast Utah

    Science.gov (United States)

    Chan, M. A.; Hasiotis, S. T.; Parrish, J. T.

    2017-12-01

    The Jurassic Navajo Sandstone of southeastern Utah is a rich archive of a desert complex with an active groundwater system, influenced by climate changes and recharge from the Uncompahgre Uplift of the Ancestral Rocky Mountains. This eastern erg margin was dominated by dune deposits of large (>10 m thick) and small (m-scale) crossbedded sandstone sets. Within these porous deposits, common soft sediment deformation is expressed as contorted and upturned bedding, fluid escape structures, concentrations of clastic pipes with ring faults, and thick intervals of massive sandstone embedded in crossbedded sandstone. Collectively, these deformation features reflect changes and/or overpressure in the groundwater system. Interdune deposits record laterally variable bounding surfaces, resulting from the change in position of and proximity to the water table. Interdune modification by pedogenesis from burrows, roots, and trees suggest stable periods of moisture and water supply, as well as periodic drying expressed as polygonal cracked mud- to sand-cracked layers. Freshwater bedded and platy limestone beds represent lakes of decameter to kilometer extent, common in the upper part of the formation. Some carbonate springs that fed the lakes are preserved as limestone buildups (tufa mounds) with microbial structures. Extradunal deposits of rivers to small ephemeral streams show channelized and lenticular, subhorizontal, cm- to m-scale sandstone bodies with basal scours and rip-up clasts. Proxy records of the active hydrology imply a changing landscape at the Navajo desert's edge, punctuated by periods of significant rainfall, runoff, rivers, lakes, and springs, fed by high water table conditions to sustain periods of flourishing communities of plants, arthropods, reptiles, mammals, and dinosaurs. Strong ground motion perturbations periodically disrupted porous, water-saturated sands with possible surface eruptions, adding to the dynamic activity of the desert regime.

  2. The sedimentology of uranium-bearing sandstones on the farm Kaffersfontein 328, Beaufort West area

    International Nuclear Information System (INIS)

    Cole, D.I.

    1979-10-01

    The sedimentology of uranium-bearing sandstones on the farm Kaffersfontein 328 was studied by use of 23 vertical profiles measured across and adjacent to 3 mineralised deposits. The profiles consist of 18 field sections and 5 borehole logs. The vertical profiles basically consist of a succession of sedimentary facies. A total of 18 facies were recognised within the fluvial sandstone sequence according to the criteria of grain-size and sedimentary structures. Transitions between the facies were subjected to a Markov chain analysis in order to delineate Markov-dependent transitions. Uranium mineralisation coincides with areas of thicker sandstone, usually where channel over-deepening has taken place. It always occurs above the base of a channel, which often marks the base of the fluvial sandstone sequence. Irregularities in the base of the channel probably caused interruptions to the flow of uraniferous solutions and allowed sufficient time for the precipitation of the uranium. Carbonaceous debris is always associated with the mineralisation and most likely acted as an indirect reductant for the precipitation of uranium from solution. The direct reductant was most probably H 2 S produced by anaerobic bacteria acting on the carbonaceous debris. The mineralisation is confined to the coarser-grained sedimentary facies, which suggests that permeability was an important control on the mineralisation. These facies probably acted as suitable aquifers for the transport of uraniferous solutions. Horizontally bedded sandstone facies comprises 41 per cent of the total cumulative thickness of mineralisation. This facies represents a higher stream power and may consequently contain more carbonaceous material derived from plants, which were eroded from upstream areas. The nature of the bedding may also have provided a more effective permeability zone for the transport of uraniferous solutions prior to precipitation of the uranium

  3. Current status and prospects of uranium geology developments of foreign in-situ leachable sandstone type uranium deposits

    International Nuclear Information System (INIS)

    Wang Zhengbang

    2002-01-01

    Firstly, with emphasis on in-situ leachable sandstone-type uranium deposits, the prospecting history of uranium deposits worldwide and its scientific research development are generally reviewed in four steps, and their basic historical experience is also summarized. Secondly, based on the detailed description of current development status of uranium geology of foreign in-situ leachable sandstone-type uranium deposits the important strategic position of sandstone-type uranium deposits in overall uranium resources all-over-the-world and its classification, spatial-temporal distribution and regulation, and metallogenic condition of sandstone-type uranium deposits are analysed thoroughly in five aspects: techtonics, paleo-climate, hydrogeology, sedimentary facies and lithology, as well as uranium sources: Afterwards, evaluation principles of three type of hyper-genic, epigenetic infiltrated sandstone-type uranium deposits are summarized. Based on sandstone-type uranium deposits located two important countries: the United States and Russia, the current development status of prospecting technology for in-situ leachable sandstone-type uranium deposits in foreign countries is outlined. Finally, according to the prospects of supply-demand development of global uranium resources, the author points out seriously that Chinese uranium geology is faced with a severe challenge, and proposes directly four strategic measures that should be taken

  4. Esophagectomy - open

    Science.gov (United States)

    ... Lewis esophagectomy, Blunt esophagectomy; Esophageal cancer - esophagectomy - open; Cancer of the esophagus - esophagectomy - open ... lining of the esophagus that can lead to cancer ( Barrett esophagus ) Severe trauma Destroyed esophagus Severely damaged stomach

  5. Determination of residual oil saturation from time-lapse pulsed neutron capture logs in a large sandstone reservoir

    International Nuclear Information System (INIS)

    Syed, E.V.; Salaita, G.N.; McCaffery, F.G.

    1991-01-01

    Cased hole logging with pulsed neutron tools finds extensive use for identifying zones of water breakthrough and monitoring oil-water contacts in oil reservoirs being depleted by waterflooding or natural water drive. Results of such surveys then find direct use for planning recompletions and water shutoff treatments. Pulsed neutron capture (PNC) logs are useful for estimating water saturation changes behind casing in the presence of a constant, high-salinity environment. PNC log surveys run at different times, i.e., in a time-lapse mode, are particularly amenable to quantitative analysis. The combined use of the original open hole and PNC time-lapse log information can then provide information on remaining or residual oil saturations in a reservoir. This paper reports analyses of historical pulsed neutron capture log data to assess residual oil saturation in naturally water-swept zones for selected wells from a large sandstone reservoir in the Middle East. Quantitative determination of oil saturations was aided by PNC log information obtained from a series of tests conducted in a new well in the same field

  6. Open access

    NARCIS (Netherlands)

    Valkenburg, P.M.

    2015-01-01

    Open access week Van 19 tot en met 25 oktober 2015 vond wereldwijd de Open Access Week plaats. Tijdens deze week werden er over de hele wereld evenementen georganiseerd waar open access een rol speelt. Ook in Nederland zijn er diverse symposia, workshops en debatten georganiseerd zoals het debat in

  7. Emplacement processes of tuffaceous sandstones at IODP Site C0011B, Nankai Trough, derived from modal analysis

    Science.gov (United States)

    Schindlbeck, J. C.; Kutterolf, S.; Freundt, A.

    2011-12-01

    Tuffaceous sandstones are characterized by their high amount (25 to 75%) of pyroclasts in their modal composition. During IODP Expedition 322 three interbeds of tuffaceous sandstones have been found within a moderately lithified and bioturbated silty claystone sequence in the late Miocene (>7.07 to ~9.0 Ma) upper part of the middle Shikoku Basin facies. Of the three sandstones, units 1 and 2 are single beds whereas unit 3 is composed of three beds. Modal analyses of 29 sandstone thin sections reveal systematic vertical changes within each bed. Generally low-density pyroclasts are enriched at the top (50-60 vol%) of each sandstone bed whereas dense lithic components (25-30 vol%) and minerals (25-30 vol%) are enriched at the bottom. The vertically varying abundance of various types of lithic fragments (sedimentary, volcanoclastic and metamorphic) suggests that these have also been segregated according to their respective densities. The highest amount of fine-grained matrix glass is found in the middle of each bed. Pumice and lithic fragments in the middle and upper parts of the sandstone beds carry ash coatings. For sandstone package 3, in contrast to 1 and 2, core pictures and thin section analyses indicate a subdivision in three units showing the same significant variations in top to bottom enrichment. This suggests three sedimentation events following each other in short time intervals. Glass and mineral chemistry of each sandstone bed show no significant vertical variations. Specifically the matrix glass-shard major element compositions are identical to the pumice clast composition in each tuffaceous sandstone bed. The compositions of amphibole and pyroxene crystals differ only slightly between the sandstone packages. Application of the Ridolfi et al. (2009) thermobarometric calculations to amphiboles of sandstone packages 1 and 2 suggests that each of these was derived from a volcanic system comprising both a deep and a shallow magma reservoir. Thickness and

  8. Application of Rock-Eval pyrolysis to the detection of hydrocarbon property in sandstone-type uranium deposits

    International Nuclear Information System (INIS)

    Sun Ye; Li Ziying; Guo Qingyin; Xiao Xinjian

    2006-01-01

    Rock-Eval pyrolysis is introduced into the research of uranium geology by means of oil-gas geochemical evaluation. Hydrocarbon (oil-gas) components in DS sandstone-type uranium deposit are detected quantitatively. Through analyzing the oil-gas bearing categories of the uranium-bearing sandstones, the internal relationships between the uranium deposit and the oil-gas are revealed. Rock-Eval pyrolysis is an effective method to study the interaction between inorganic and organic matters, and should be extended to the study of sandstone-type uranium deposits. (authors)

  9. Preliminary research on finite difference method to solve radon field distribution over sandstone-type uranium ore body

    International Nuclear Information System (INIS)

    Li Bihong; Shuang Na; Liu Qingcheng

    2006-01-01

    The principle of finite difference method is introduced, and the radon field distribution over sandstone-type uranium deposit is narrated. The radon field distribution theory equation is established. To solve radon field distribution equation using finite difference algorithm is to provide the value computational method for forward calculation about radon field over sandstone-type uranium mine. Study on 2-D finite difference method on the center of either high anomaly radon fields in view of the character of radon field over sandstone-type uranium provide an algorithm for further research. (authors)

  10. Permeability in Rotliegend gas sandstones to gas and brine as predicted from NMR, mercury injection and image analysis

    DEFF Research Database (Denmark)

    Rosenbrand, Esther; Fabricius, Ida Lykke; Fisher, Quentin

    2015-01-01

    Permeability characterisation of low permeability, clay-rich gas sandstones is part of production forecasting and reservoir management. The physically based Kozeny (1927) equation linking permeability with porosity and pore size is derived for a porous medium with a homogeneous pore size, whereas...... the pore sizes in tight sandstones can range from nm to μm. Nuclear magnetic resonance (NMR) transverse relaxation was used to estimate a pore size distribution for 63 samples of Rotliegend sandstone. The surface relaxation parameter required to relate NMR to pore size is estimated by combination of NMR...

  11. CHARACTERIZATION OF SANDSTONE RESERVOIRS FOR ENHANCED OIL RECOVERY: THE PERMIAN UPPER MINNELUSA FORMATION, POWDER RIVER BASIN, WYOMING.

    Science.gov (United States)

    Schenk, C.J.; Schmoker, J.W.; Scheffler, J.M.

    1986-01-01

    Upper Minnelusa sandstones form a complex group of reservoirs because of variations in regional setting, sedimentology, and diagenetic alteration. Structural lineaments separate the reservoirs into northern and southern zones. Production in the north is from a single pay sand, and in the south from multi-pay sands due to differential erosion on top of the Upper Minnelusa. The intercalation of eolian dune, interdune, and sabkha sandstones with marine sandstones, carbonates, and anhydrites results in significant reservoir heterogeneity. Diagenetic alterations further enhance heterogeneity, because the degree of cementation and dissolution is partly facies-related.

  12. Rhythmic constraints in durational control

    NARCIS (Netherlands)

    Grover, C.N.; Terken, J.M.B.

    1994-01-01

    Two potential factors in durational control are addressed. First, we investigate whether lengthening a syllable implies lengthening all of its constituent phonemes in a regular way. Analysis of a small corpus of syllables shows that this is not the case. Second, we investigate the influence of

  13. Rent control and unemployment duration

    DEFF Research Database (Denmark)

    Svarer, Michael; Rosholm, Michael; Munch, Jakob Roland

    2005-01-01

    In this paper we analyse how rent control affects the duration of individual unemployment. In atheoretical search model we distinguish between two effects of rent control. On one hand, rentcontrol reduces housing mobility and hence mobility in the labour market. On the other hand, tomaintain rent...

  14. JACEE long duration balloon flights

    International Nuclear Information System (INIS)

    Burnett, T.; Iwai, J.; Lord, J.J.; Strausz, S.; Wilkes, R.J.; Dake, S.; Oda, H.; Miyamura, O.; Fuki, M.; Jones, W.V.; Gregory, J.; Hayashi, T.; Takahashi, U.; Tominaga, Y.; Wefel, J.P.; Fountain, W.; Derrickson, J.; Parnell, T.A.; Roberts, E.; Tabuki, T.; Watts, J.W.

    1989-01-01

    JACEE balloon-borne emulsion chamber detectors are used to observe the spectra and interactions of cosmic ray protons and nuclei in the energy range 1-100A TeV. Experience with long duration mid-latitude balloon flights and characteristics of the detector system that make it ideal for planned Antarctic balloon flights are discussed. 5 refs., 2 figs

  15. Pancreatitis versus open epiphysiodesis

    International Nuclear Information System (INIS)

    Al-Zahrani, Adnan G.; Al-Hossain, Mohammad H.; Aab, F.; Yaser, M.; Alammari, A.

    2003-01-01

    Epiphysiodesis is used for treatment of leg -length discrepancy in skeletally immature patients.Phemister described an open technique that requires surgical dissection with potential morbidity. Recently minimally invasive approaches that utilize intraoperative fluoroscopy have been introduced. The aim of this study is to compare our experience using the open and the minimally invasive percutaneous techniques. A prospective follow-up of 87 consecutive patients undergoing epiphysiodesis for correction of post traumetic leg-length discrepancy using either the open or the percutaneous technique at the Armed Forces Hospital ,Riyadh,Kingdom of Saudi Arabia between January 1993 and December 2000. Out of 87 patients , 52 were carried out using the open technique and 35 were utilized by this percutaneous technique.There was no statistically significant between two groups in terms of demographic date ,operative time,perioperative complications or time required to achieve the growth arrest. However there was a significant difference in the hospital stay and postoperative need for physiotherapy .The percutaneous group had a short hospitalization (average 2.5 days )compared to open technique group (average 4 days). Our experience is similarto what is reported in the literature and confirms that the percutaneous technique has an advatage over the open technique with shorter hospitalization and less duration of physiotherapy. (author) =

  16. Open Content in Open Context

    Science.gov (United States)

    Kansa, Sarah Whitcher; Kansa, Eric C.

    2007-01-01

    This article presents the challenges and rewards of sharing research content through a discussion of Open Context, a new open access data publication system for field sciences and museum collections. Open Context is the first data repository of its kind, allowing self-publication of research data, community commentary through tagging, and clear…

  17. Chemical and physical hydrogeology of coal, mixed coal-sandstone and sandstone aquifers from coal-bearing formations in the Alberta Plains region, Alberta

    International Nuclear Information System (INIS)

    Lemay, T.G.

    2003-09-01

    With the decline of conventional oil and gas reserves, natural gas from coal (NGC) is an unconventional gas resource that is receiving much attention from petroleum exploration and development companies in Alberta. Although the volume of the NGC resource is large, there are many challenges facing NGC development in Alberta, including technical and economic issues, land access, water disposal, water diversion and access to information. Exploration and development of NGC in Alberta is relatively new, therefore there is little baseline data on which to base regulatory strategies. Some important information gaps have been filled through water well sampling in coal, mixed coal-sandstone and sandstone aquifers throughout Alberta. Analyses focused on the chemical and physical characteristics aquifers in use for domestic or agricultural purposes. Aquifer depths were generally less than 100 metres. Samples collected from Paskapoo-Scollard Formation, Horseshoe Canyon Formation and Belly River Group aquifers exceed Canadian water quality guideline values with respect to pH, sodium, manganese, chloride, chromium, sulphate, phenols and total dissolved solids. Pump tests conducted within the aquifers indicate that the groundwater flow is complicated. Water quality will have to be carefully managed to ensure responsible disposal practices are followed. Future studies will focus on understanding the chemical and biological process that occur within the aquifers and the possible link between these processes and gas generation. Mitigation and disposal strategies for produced water will also be developed along with exploration strategies using information obtained from hydrogeologic studies. 254 refs., 182 tabs., 100 figs., 3 appendices

  18. Weak openness and almost openness

    Directory of Open Access Journals (Sweden)

    David A. Rose

    1984-01-01

    Full Text Available Weak openness and almost openness for arbitrary functions between topological spaces are defined as duals to the weak continuity of Levine and the almost continuity of Husain respectively. Independence of these two openness conditions is noted and comparison is made between these and the almost openness of Singal and Singal. Some results dual to those known for weak continuity and almost continuity are obtained. Nearly almost openness is defined and used to obtain an improved link from weak continuity to almost continuity.

  19. REE characteristics and uranium metallogenesis of sandstone-type uranium deposits in northern Sichuan

    International Nuclear Information System (INIS)

    Zhu Xiyang; Wang Yunliang; Wang Zhichang; Zhang Chengjiang

    2004-01-01

    On the basis of the analysis of a large number of samples at sandstone-type uranium deposits in northern Sichuan, this paper analyses the REE composition of country rocks, ores, calcite-veins and uranium minerals, and systematically summarizes their REE geochemical characteristics, and discusses variation regularity of REE during depositional and diagenetic processes. By comparing these characteristics with those of typical hydrothermal volcanics-type and metamorphic rock type uranium deposits both at home and abroad, authors suggest that sandstone-type uranium deposits in northern Sichuan are characterized by REE geochemical features of hydrothermal reworking metallogenesis, the uranium mineralization has experienced two stages: the diagenetic preconcentration and the concentration of hydrothermal reworking

  20. Remote sensing technology prospecting methods of interlayer oxidation zone type sandstone uranium deposit in Yili basin

    International Nuclear Information System (INIS)

    Huang Xianfang; Huang Shutao; Pan Wei; Feng Jie; Liu Dechang; Zhang Jingbo; Xuan Yanxiu; Rui Benshan

    1998-12-01

    Taking Yili Basin as an example, remote sensing technology and method of interlayer oxidation zone type sandstone uranium deposit have systematically been summarized. Firstly, principle, methods and procedures of the second development of scientific experimental satellite photograph have been elaborated in detail. Three dimensional stereo simulation, display, and multi-parameters extraction have been recommended. Secondarily, the research is focused on prospective section image features in different type images and their geological implications and on establishing recognition keys of promising areas. Finally, based on above research results, three graded predictions, i.e. regional prospect, promising sections and favourable location in the deposit have been made step by step and reconnaissance and prospecting range are gradually reduced. The practice has indicated that breakthrough progress has been made in application to prospect prognosis of interlayer oxidation zone type sandstone uranium deposit and good verified results have been obtained

  1. Hydrogeochemical and stream sediment sampling for uranium in the sandstone environment

    International Nuclear Information System (INIS)

    Wenrich, K.J.

    1985-01-01

    Sandstone terranes commonly host uranium occurrences in the western United States. In addition, because sedimentary terranes, particularly shales and immature, not well cemented sandstone, contribute more sediment and soluble material than do plutonic, volcanic, or metamorphic terranes they are an excellent regime for hydrogeochemical and stream-sediment prospecting. Because of higher conductivity, and hence higher uranium content, of waters draining such environments the sampling need not be as precise nor the analytical detection limit as low as in other terranes to yield a successful survey. Nevertheless, reasonable preparation and care of the samples is recommended: (1) The water samples should be filtered through 0.45 μm membranes and acidified to a pH of less than 1. (2) Because the adsorption of uranium by organic material is so significant it is recommended that the reasonable finest stream-sediment fraction, 4 , conductivity, etc.) are useful in the data reduction towards the elimination of false anomalies. (author)

  2. Simulation of forced convection in non-Newtonian fluid through sandstones

    Science.gov (United States)

    Gokhale, M. Y.; Fernandes, Ignatius

    2017-11-01

    Numerical simulation is carried out to study forced convection in non-Newtonian fluids flowing through sandstones. Simulation is carried out using lattice Boltzmann method (LBM) for both shear-thinning and shear-thickening, by varying the power law index from 0.5 to 1.5 in Carreau-Yasuda model. Parameters involved in LBM and Carreau model are identified to achieve numerical convergence. Permeability and porosity are varied in the range of 10-10-10-6 and 0.1-0.7, respectively, to match actual geometrical properties of sandstone. Numerical technology is validated by establishing Darcy's law by plotting the graph between velocity and pressure gradient. Consequently, investigation is carried out to study the influence of material properties of porous media on flow properties such as velocity profiles, temperature profiles, and Nusselt number.

  3. Tectono-sedimentary evolution of Erlian basin since late mesozoic and sandstone-hosted uranium metallogenesis

    International Nuclear Information System (INIS)

    Wei Sanyuan; Qin Mingkuan; Li Yuexiang; He Zhongbo; Chen Anping; Shen Kefeng; Cao Jianying

    2006-01-01

    Various mineral resources in a basin are associated with its tectono-sedimentary evolution. Based on the analysis of the tectono-sedimentary evolution of Erlian basin, three evolutional stages of Erlian basin are classified, they are: the continental extensional down-faulting stage, the transitional stage from down-faulting to down-warping in Early Cretaceous, and slightly compressional differentiated uplifting-subsidence since Late Cretaceous. According to the mechanism of sandstone-hosted uranium metallogenesis it is suggested that the grey clastic rock series deposited at the stage of down-faulting down-warping transition must be the important target for uranium prospecting, and the differentiated uplifting-subsidence offers necessary conditions for sandstone-hosted uranium ore-formation. Then, types of uranium mineralization that could occur in Erlian basin are discussed, and uranium metallogenic model has been preliminarily summarized. (authors)

  4. Pore Fluid Effects on Shear Modulus for Sandstones with Soft Anisotropy

    International Nuclear Information System (INIS)

    Berryman, J G

    2004-01-01

    A general analysis of poroelasticity for vertical transverse isotropy (VTI) shows that four eigenvectors are pure shear modes with no coupling to the pore-fluidmechanics. The remaining two eigenvectors are linear combinations of pure compression and uniaxial shear, both of which are coupled to the fluid mechanics. After reducing the problem to a 2x2 system, the analysis shows in a relatively elementary fashion how a poroelastic system with isotropic solid elastic frame, but with anisotropy introduced through the poroelastic coefficients, interacts with the mechanics of the pore fluid and produces shear dependence on fluid properties in the overall mechanical system. The analysis shows, for example, that this effect is always present (though sometimes small in magnitude) in the systems studied, and can be quite large (up to a definite maximum increase of 20 per cent) in some rocks--including Spirit River sandstone and Schuler-Cotton Valley sandstone

  5. A economic evaluation system software on in-situ leaching mining sandstone uranium deposits

    International Nuclear Information System (INIS)

    Yao Yixuan; Su Xuebin; Xie Weixing; Que Weimin

    2001-01-01

    The author presents the study results of applying computer technology to evaluate quantitatively the technical-economic feasibility of in-situ leaching mining sandstone uranium deposits. A computer system software have been developed. Under specifying deposit conditions and given production size per year, the application of the software will generate total capital and mine life operating costs as well as solve for the movable and static financial assessment targets through discounted cash flow analysis. According to the characters of two kinds of sandstone uranium deposits, a data bases of economic and technique parameters of in-situ leaching have been designed. Also the system software can be used to study the economic value of deposits and to optimize the key project parameters. Its features, data input method and demand, main functions, structure and operating environments are described

  6. Uranium isotopes in groundwater: their use in prospecting for sandstone-type uranium deposits

    International Nuclear Information System (INIS)

    Cowart, J.B.; Osmond, J.K.

    1977-01-01

    The relative abundances of dissolved 238 U and its daughter 234 U appear to be greatly affected as the uranium is transported downdip in sandstone aquifers. In an actively forming uranium accumulation at a reducing barrier, an input of 234 U occurs in proximity to the isotopically non-selective precipitation of uranium from the water. The result is a downdip water much lower in uranium concentration but relatively enriched in 234 U. The measurement of isotopic as well as concentration changes may increase the effectiveness of hydrogeochemical exploration of uranium. The investigation includes the uranium isotopic patterns in aquifers associated with known uranium orebodies in the Powder River and Shirley Basins, Wyoming, and Karnes County, Texas, USA. In addition, the Carrizo sandstone aquifer of Texas was studied in detail and the presence of an uranium accumulation inferred

  7. Hydrophobization by Means of Nanotechnology on Greek Sandstones Used as Building Facades

    Directory of Open Access Journals (Sweden)

    Georgios Karagiannis

    2013-01-01

    Full Text Available Modern sustainable architecture indicates the use of local natural stones for building. Greek sandstones from Epirus (Demati, Greece, EN 12440 used as building facades meet aesthetic and have high mechanical properties, but the inevitable interaction between stone materials and natural or anthropogenic weathering factors controls the type, and extent of stone damages. In the present paper, samples of sandstone were treated with a conventional hydrophobic product and four solutions of the same product, enriched with nanosilica of different concentrations. The properties of the treated samples, such as porosity and pore size distribution, microstructure, static contact angle of a water droplet, and durability to deterioration cycles (freeze-thaw were recorded and conclusions were drawn. The research indicates the increased hydrophobic properties in nanosilica solutions but also the optimum content in nanoparticles that provides hydrophobicity without altering the properties of the stone.

  8. Spatial distribution of epibenthic molluscs on a sandstone reef in the Northeast of Brazil

    Directory of Open Access Journals (Sweden)

    AS. Martinez

    Full Text Available The present study investigated the distribution and abundance of epibenthic molluscs and their feeding habits associated to substrate features (coverage and rugosity in a sandstone reef system in the Northeast of Brazil. Rugosity, low coral cover and high coverage of zoanthids and fleshy alga were the variables that influenced a low richness and high abundance of a few molluscan species in the reef habitat. The most abundant species were generalist carnivores, probably associated to a lesser offer and variability of resources in this type of reef system, when compared to the coral reefs. The results found in this study could reflect a normal characteristic of the molluscan community distribution in sandstone reefs, with low coral cover, or could indicate a degradation state of this habitat if it is compared to coral reefs, once that the significantly high coverage of fleshy alga has been recognized as a negative indicator of reef ecosystems health.

  9. Spatial distribution of epibenthic molluscs on a sandstone reef in the Northeast of Brazil.

    Science.gov (United States)

    Martinez, A S; Mendes, L F; Leite, T S

    2012-05-01

    The present study investigated the distribution and abundance of epibenthic molluscs and their feeding habits associated to substrate features (coverage and rugosity) in a sandstone reef system in the Northeast of Brazil. Rugosity, low coral cover and high coverage of zoanthids and fleshy alga were the variables that influenced a low richness and high abundance of a few molluscan species in the reef habitat. The most abundant species were generalist carnivores, probably associated to a lesser offer and variability of resources in this type of reef system, when compared to the coral reefs. The results found in this study could reflect a normal characteristic of the molluscan community distribution in sandstone reefs, with low coral cover, or could indicate a degradation state of this habitat if it is compared to coral reefs, once that the significantly high coverage of fleshy alga has been recognized as a negative indicator of reef ecosystems health.

  10. Integrated prediction based on GIS for sandstone-type uranium deposits in the northwest of Ordos Basin

    International Nuclear Information System (INIS)

    Han Shaoyang; Ke Dan; Hu Shuiqing; Guo Qingyin; Hou Huiqun

    2005-01-01

    The integrated prediction model of sandstone-type uranium deposits and its integrated evaluation methods as well as flow of the work based on GIS are studied. A software for extracting metallogenic information is also developed. A multi-source exploring information database is established in the northwest of Ordos Basin, and an integrated digital mineral deposit prospecting model of sandstone-type uranium deposits is designed based on GIS. The authors have completed metallogenic information extraction and integrated evaluation of sandstone-type uranium deposits based on GIS in the study area. Research results prove that the integrated prediction of sandstone-type uranium deposits based on GIS may further delineate prospective target areas rapidly and improve the predictive precision. (authors)

  11. How Pore Filling Shale Affects Elastic Wave Velocities in Fully and Partially Saturated Sandstone: Characterization, Measurement, and Modelling

    DEFF Research Database (Denmark)

    Sørensen, Morten Kanne; Fabricius, Ida Lykke

    2017-01-01

    The elastic bulk modulus of a sandstone is affected by the fluid saturation as compression induces a pressure in the fluid thus increasing the bulk modulus of the sandstone as a whole. Assuming a uniform induced pressure and no interaction between the saturating fluid and the solid rock the fluid...... contribution to the elastic bulk modulus is quantified by Gassmann's equations. Experimental measurements of the fluid contribution to the elastic moduli are, however often much larger than predicted within the assumptions of Gassmann. Clay-rich low-mobility sandstones are especially prone to having elastic...... moduli highly sensitive to the fluid saturation. The presence of clay in a sandstone can affect two of the underlying assumptions to Gassmann's equations: decreased fluid mobility can cause pressure gradients and fluid-clay interactions are common. The elastic and petrophysical properties of clay...

  12. Characterization of application of acu sandstone in ceramic mass; Caracterizacao da aplicacao do arenito acu na massa ceramica

    Energy Technology Data Exchange (ETDEWEB)

    Nobrega, L.F.P.M.; Souza, M.M.; Gomes, Y.S.; Fernandes, D.L., E-mail: junior.luiz09@hotmail.com [Universidade Federal do Rio Grande do Norte (DIAREN/UFRN), Natal, RN (Brazil). Laboratorio de Processamento Mineral e Residuo

    2016-07-01

    The sandstone is a sedimentary rock formed mainly by quartz grains. In Rio Grande do Norte, there is the Potiguar Basin with the Jandaira and Acu Formations. The latter consists of thick layers of whitish-colored sandstones. It stands out as a water storage facility in the state, but it is also used for building aggregates. This article aimed at the use of the sandstone of this formation in the ceramic mass for coating. Initially, the material was sampled. It went through the comminution process to achieve the required granulometry. After this, three formulations were made to incorporate this new material into the traditional ones. The methods were performed according to ISO 13816. After sintering at 1200 °C, the specimens were subjected to the physical tests. A positive result was obtained for the use of the Acu sandstone in low concentrations. It is clear, therefore, its use in ceramics for coating.

  13. Tertiary lithofacies and paleo-geographic framework and interlayer oxidation zone sandstone uranium deposits in Longjiang-Zhaozhou area

    International Nuclear Information System (INIS)

    Zhang Zhenqiang

    2003-01-01

    The main points of views for the experiment are: (1) Yi'an formation is mainly composed of limnetic facies of siltstone and fine sandstone, due to weak surface water, limited sedimentation and simple material source; (2) strengthened surface water and enormous material brought from north and west-north and enlarged sedimentation from north to south, the major deposition during Da'an period are channel facies of conglomerate and river bed facies of sandstone; (3) stronger surface water during Taikang period, led alluvial-flood plain facies brown-yellow conglomerate to develop along western margin of the basin, the channel facies of conglomerate and river bed facies of grey-green sandstone, pelitic siltstone were widely formed southward and eastward; (4) according to the lithofacies criterion for in-situ leachable sandstone uranium ore, Taikang formation is an ideal horizon, river bed facies is suitable for interlayer oxidation type uranium deposit. (author)

  14. Metallogenic characteristics, model and exploration prospect for the paleo-interlayer-oxidation type sandstone-hosted uranium deposits in China

    International Nuclear Information System (INIS)

    Huang Jingbai; Li Shengxiang

    2007-01-01

    In this paper, the paleo-interlayer-oxidation type sandstone-hosted uranium deposits occurred in the Meso-Cenozoic continental basins in China are divided into 3 subtype, they are stratum over lapping buried subtype, structure-uplifting destroy subtype and faulted-folding conserved subtype. The metallogenic characteristics, metallogenic model and exploration prospect for these 3 subtypes uranium deposits are discussed. It is proposed that the paleo-interlayer-oxidation type sandstone-hosted uranium deposits, besides the recent interlayer oxidation type sandstone-hosted uranium deposits, are of great prospecting potential in the Meso-Cenozoic continental basins in China. Therefore, the metallogenic theory of these types uranium deposits should be conscientiously summarized and replenished continuously so as to propel forward the exploration of the sandstone-hosted uranium deposits in China. (authors)

  15. Wind-blown sandstones cemented by sulfate and clay minerals in Gale Crater, Mars

    OpenAIRE

    Milliken, R. E.; Ewing, Ryan C.; Fischer, W. W.; Hurowitz, J.

    2014-01-01

    Gale Crater contains Mount Sharp, a ~5km thick stratigraphic record of Mars’ early environmental history. The strata comprising Mount Sharp are believed to be sedimentary in origin, but the specific depositional environments recorded by the rocks remain speculative. We present orbital evidence for the occurrence of eolian sandstones within Gale Crater and the lower reaches of Mount Sharp, including preservation of wind-blown sand dune topography in sedimentary strata—a phenomenon ...

  16. Application of comprehensive geophysical methods to prospecting for sandstone-type uranium deposit in Bayanmaodu basin

    International Nuclear Information System (INIS)

    Yao Yifeng; Sun Zexuan; Chen Zhiguo; He Tao; Li Guoxin

    2003-01-01

    By using comprehensive geophysical methods including magnetic survey, resistivity sounding, self potential survey, 210 Po survey etc., the shape and the depth of the basement, the structure of the sedimentary cover, characteristics of prospecting target horizon, the development of interlayer oxidation zone at depth, as well as the information of uranium mineralization have been basically revealed, thus providing a basis for the prospect evaluation of sandstone-type uranium mineralization in the basin

  17. Biologically-initiated rock crust on sandstone: Mechanical and hydraulic properties and resistance to erosion

    Czech Academy of Sciences Publication Activity Database

    Slavík, M.; Bruthans, J.; Filippi, Michal; Schweigstillová, Jana; Falteisek, L.; Řihošek, J.

    2017-01-01

    Roč. 278, FEB 1 (2017), s. 298-313 ISSN 0169-555X R&D Projects: GA ČR GA13-28040S; GA ČR(CZ) GA16-19459S Institutional support: RVO:67985831 ; RVO:67985891 Keywords : biofilm * biocrust * biologically-initiated rock crust * sandstone protection * case hardening Subject RIV: DB - Geology ; Mineralogy; DB - Geology ; Mineralogy (USMH-B) OBOR OECD: Geology; Geology (USMH-B) Impact factor: 2.958, year: 2016

  18. Improving recovery efficiency of water-drive channel sandstone reservoir by drilling wells laterally

    Energy Technology Data Exchange (ETDEWEB)

    Zhiguo, F.; Quinglong, D.; Pingshi, Z.; Bingyu, J.; Weigang, L. [Research Institute of Exploration and Development, Daqing (China)

    1998-12-31

    Example of drilling a horizontal well in reservoir rock of only four meter thick by using existing casing pipe of low efficiency vertical wells to induce production in the top remaining reservoir is described. The experience shows that drilling horizontal wells laterally in thin bodies of sandstone reservoirs and improve their productivity is a feasible proposition. Productivity will still be low, but it can be improved by well stimulation. 3 refs., 3 figs.

  19. Electrical Spectroscopy of Permo-Triassic Sandstone From the United Kingdom

    Science.gov (United States)

    Scott, J.; Barker, R.

    2003-12-01

    Electrical spectroscopy measurements in the range of mHz to kHz have been made on the dominantly red Permo-Triassic sandstone from the United Kingdom. Samples have been selected from borehole cores from all of the main outcrop areas of sandstone and represent a wide variety of lithologies. This sandstone is an important aquifer for several major cities including Manchester and Birmingham. The samples have been fully saturated with sodium chloride brines and a synthetic groundwater solution that is higher in calcium and magnesium ions than sodium and which closely matches the cation concentrations of the groundwater at Birmingham. Electrical measurements were made using a four-electrode arrangement of silver-silver chloride electrodes. Most of the electrical spectra show a clear, slightly asymmetric, electrical relaxation phenomenon with relaxation peaks in the range of 0.001 Hz to 20 Hz. These relaxation phenomena can be fitted very well by a generalised Cole-Cole model. The relaxation time from this model is found to correlate closely with the dominant pore-throat size from mercury injection. Normalising the chargeability, Cole-Cole m parameter, by the conductivity gives a polarisation magnitude which correlates well with the pore surface to volume ratio (SPOR) for sandstone samples with an even distribution of surface coating clays. The information obtained from the electrical spectra is very useful. The pore-throat size is important in controlling the permeability and in particular the flow of non-aqueous phase fluids. The pore surface area has links to the sorbtion properties of the rock, which are important in estimating contaminant transport. The electrical spectra also provide a useful fingerprint of individual lithologies which could be used for correlation between boreholes or outcrops.

  20. Endolithic algae of semi-desert sandstones: systematic, biogeographic and ecophysiologic investigations

    International Nuclear Information System (INIS)

    Bell, R.A.

    1986-01-01

    Investigations were conducted into the ecology of an unusual algal community in northern Arizona. These microorganisms are called endolithic algae because they occur beneath the surface of rocks. Eighteen taxa, including representatives of both eukaryotic and prokaryotic genera, were isolated from below the surface of eight sandstones in four semi-desert and cold temperate biomes of the Colorado Plateau. As the macroclimate of the area changes from cold temperature desert scrub to cold temperate forest the taxonomic composition of the endolithic algal communities shifts from domination by coccoid blue-green algae to domination by coccoid and sarcinoid green algae. The algal communities varied in generic composition, chlorophyll a content, and in their location within the different sandstones. Investigations into the microclimate of the endolithic algal zone in two adjacent but differently-colored sections (white and brown) of Coconino sandstone have demonstrated differences between the environment above the rock surface and that just beneath the surface. In seasonal samples of the Coconino sandstone, chlorophyll a content ranged from 50 to 100 mg x m -2 in the white rock and 8 to 45 mg x m -2 in the brown rock. Primary production (as measured by 14 CO 2 incorporation) displayed marked seasonal patterns that appear to be correlated to the environmental conditions within the rocks as opposed to those outside the rocks. The widespread distribution of certain algae in the endolithic habitats of the Colorado Plateau and their presence in rocks at quite distant locations suggests that the endolithic habitat may be utilized by algae whenever it provides more favorable conditions than the surrounding surfaces

  1. Sandstone columns of the 3rd Nile Cataract (Nubia, Northern Sudan)

    Czech Academy of Sciences Publication Activity Database

    Cílek, Václav; Adamovič, Jiří; Suková, L.

    2015-01-01

    Roč. 59, Supplement 1 (2015), s. 151-165 ISSN 0372-8854 Grant - others:Program interní podpory projektů mezinárodní spolupráce AV ČR(CZ) M100130902 Institutional support: RVO:67985831 Keywords : Nubian sandstone * columnar jointing * Voronoi fragmentation * 3rd Nile Cataract * Sudan Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.103, year: 2015

  2. Quantitative study of a rapidly weathering overhang developed in an artificially wetted sandstone cliff

    Czech Academy of Sciences Publication Activity Database

    Bruthans, J.; Filippi, Michal; Schweigstillová, Jana; Řihošek, J.

    2017-01-01

    Roč. 42, č. 5 (2017), s. 711-723 ISSN 0197-9337 R&D Projects: GA ČR GA13-28040S Institutional support: RVO:67985831 ; RVO:67985891 Keywords : sandstone overhang * retreat * frost weathering * erosion rate * stress Subject RIV: DB - Geology ; Mineralogy; DB - Geology ; Mineralogy (USMH-B) OBOR OECD: Geology; Geology (USMH-B) Impact factor: 3.697, year: 2016

  3. A New Multichelating Acid System for High-Temperature Sandstone Reservoirs

    Directory of Open Access Journals (Sweden)

    Nianyin Li

    2015-01-01

    Full Text Available Sandstone reservoir acidizing is a complex and heterogeneous acid-rock reaction process. If improper acid treatment is implemented, further damage can be induced instead of removing the initial plug, particularly in high-temperature sandstone reservoirs. An efficient acid system is the key to successful acid treatment. High-temperature sandstone treatment with conventional mud acid system faces problems including high acid-rock reaction rate, short acid effective distance, susceptibility to secondary damage, and serious corrosion to pipelines. In this paper, a new multichelating acid system has been developed to overcome these shortcomings. The acid system is composed of ternary weak acid, organic phosphonic chelating agent, anionic polycarboxylic acid chelating dispersant, fluoride, and other assisted additives. Hydrogen ion slowly released by multistage ionization in ternary weak acid and organic phosphonic within the system decreases the concentration of HF to achieve retardation. Chelating agent and chelating dispersant within the system inhibited anodic and cathodic reaction, respectively, to protect the metal from corrosion, while chelating dispersant has great chelating ability on iron ions, restricting the depolarization reaction of ferric ion and metal. The synergic effect of chelating agent and chelating dispersant removes sulfate scale precipitation and inhibits or decreases potential precipitation such as CaF2, silica gel, and fluosilicate. Mechanisms of retardation, corrosion-inhibition, and scale-removing features have been discussed and evaluated with laboratory tests. Test results indicate that this novel acid system has good overall performance, addressing the technical problems and improving the acidizing effect as well for high-temperature sandstone.

  4. Experimental Investigation of Crack Extension Patterns in Hydraulic Fracturing with Shale, Sandstone and Granite Cores

    Directory of Open Access Journals (Sweden)

    Jianming He

    2016-12-01

    Full Text Available Hydraulic fracturing is an important method of reservoir stimulation in the exploitation of geothermal resources, and conventional and unconventional oil and gas resources. In this article, hydraulic fracturing experiments with shale, sandstone cores (from southern Sichuan Basin, and granite cores (from Inner Mongolia were conducted to investigate the different hydraulic fracture extension patterns in these three reservoir rocks. The different reactions between reservoir lithology and pump pressure can be reflected by the pump pressure monitoring curves of hydraulic fracture experiments. An X-ray computer tomography (CT scanner was employed to obtain the spatial distribution of hydraulic fractures in fractured shale, sandstone, and granite cores. From the microscopic and macroscopic observation of hydraulic fractures, different extension patterns of the hydraulic fracture can be analyzed. In fractured sandstone, symmetrical hydraulic fracture morphology could be formed, while some micro cracks were also induced near the injection hole. Although the macroscopic cracks in fractured granite cores are barely observed by naked eye, the results of X-ray CT scanning obviously show the morphology of hydraulic fractures. It is indicated that the typical bedding planes well developed in shale formation play an important role in the propagation of hydraulic fractures in shale cores. The results also demonstrated that heterogeneity influenced the pathway of the hydraulic fracture in granite cores.

  5. Formation factor in Bentheimer and Fontainebleau sandstones: Theory compared with pore-scale numerical simulations

    Science.gov (United States)

    Ghanbarian, Behzad; Berg, Carl F.

    2017-09-01

    Accurate quantification of formation resistivity factor F (also called formation factor) provides useful insight into connectivity and pore space topology in fully saturated porous media. In particular the formation factor has been extensively used to estimate permeability in reservoir rocks. One of the widely applied models to estimate F is Archie's law (F = ϕ- m in which ϕ is total porosity and m is cementation exponent) that is known to be valid in rocks with negligible clay content, such as clean sandstones. In this study we compare formation factors determined by percolation and effective-medium theories as well as Archie's law with numerical simulations of electrical resistivity on digital rock models. These digital models represent Bentheimer and Fontainebleau sandstones and are derived either by reconstruction or directly from micro-tomographic images. Results show that the universal quadratic power law from percolation theory accurately estimates the calculated formation factor values in network models over the entire range of porosity. However, it crosses over to the linear scaling from the effective-medium approximation at the porosity of 0.75 in grid models. We also show that the effect of critical porosity, disregarded in Archie's law, is nontrivial, and the Archie model inaccurately estimates the formation factor in low-porosity homogeneous sandstones.

  6. Trap architecture of the Early Cretaceous Sarir Sandstone in the eastern Sirt Basin, Libya

    Energy Technology Data Exchange (ETDEWEB)

    Gras, R. [Schlumberger GeoQuest, Cedex (France); Thusu, B. [Arabian Gulf Oil Company, Benghazi (Libyan Arab Jamahiriya)

    1998-12-31

    The Sarir Sandstone is the principal reservoir for oil accumulations in the eastern Sirt Basin in Libya. The main phase of the rifting in this area took place in the Late Jurassic-Early Cretaceous, during which time the Sarir Sandstone was deposited as a non-marine, intra-continental clastic syn-rift sequence. Although successfully explored from 1959 onwards, the prolific eastern Sirt Basin is in a relatively immature stage of exploration regarding wildcat drilling and 3D seismic data acquisition. The most recent phase of exploration, utilizing 3D seismic techniques, revealed a complex structural development. The trap geometries are often related to E-W trending, basement-controlled fault systems, oblique to the NNW-SSE Sirt Basin trend. The fault systems were active during the Sarir Sandstone deposition, giving rise to structural as well as combined structural-traps. An increased understanding of trap architecture has led to both re-evaluation of older fields and new discoveries. (author)

  7. Experimental Study of Cement - Sandstone/Shale - Brine - CO2 Interactions.

    Science.gov (United States)

    Carroll, Susan A; McNab, Walt W; Torres, Sharon C

    2011-11-11

    Reactive-transport simulation is a tool that is being used to estimate long-term trapping of CO2, and wellbore and cap rock integrity for geologic CO2 storage. We reacted end member components of a heterolithic sandstone and shale unit that forms the upper section of the In Salah Gas Project carbon storage reservoir in Krechba, Algeria with supercritical CO2, brine, and with/without cement at reservoir conditions to develop experimentally constrained geochemical models for use in reactive transport simulations. We observe marked changes in solution composition when CO2 reacted with cement, sandstone, and shale components at reservoir conditions. The geochemical model for the reaction of sandstone and shale with CO2 and brine is a simple one in which albite, chlorite, illite and carbonate minerals partially dissolve and boehmite, smectite, and amorphous silica precipitate. The geochemical model for the wellbore environment is also fairly simple, in which alkaline cements and rock react with CO2-rich brines to form an Fe containing calcite, amorphous silica, smectite and boehmite or amorphous Al(OH)3. Our research shows that relatively simple geochemical models can describe the dominant reactions that are likely to occur when CO2 is stored in deep saline aquifers sealed with overlying shale cap rocks, as well as the dominant reactions for cement carbonation at the wellbore interface.

  8. An Experimental Study of the Fracture Coalescence Behaviour of Brittle Sandstone Specimens Containing Three Fissures

    Science.gov (United States)

    Yang, S. Q.; Yang, D. S.; Jing, H. W.; Li, Y. H.; Wang, S. Y.

    2012-07-01

    To analyse the fracture coalescence behaviour of rock, rectangular prismatic sandstone specimens (80 × 160 × 30 mm in size) containing three fissures were tested under uniaxial compression. The strength and deformation behaviours of the specimens are first analysed by investigating the effects of the ligament angle β2 on the peak strength, peak strain and crack initiation stress of the specimens. To confirm the sequence of crack coalescence, a photographic monitoring technique is used throughout the entire period of deformation. Based on the results, the relationship between the real-time crack coalescence process and the axial stress-strain curve of brittle sandstone specimens is also developed, and this relationship can be used to evaluate the macroscopic deformation characteristics of pre-cracked rock. The equivalent strain evolution fields of the specimen, with α = β1 = 45° and β2 = 90°, are obtained using the digital image correlation technique and show good agreement with the experimental results of pre-cracked brittle sandstone. These experimental results are expected to improve the understanding of fracture mechanisms and be used in rock engineering with intermittent structures, such as deep underground excavated tunnels.

  9. Methodology for the design of the method of siliceous sandstones operation using special software

    Directory of Open Access Journals (Sweden)

    Luis Ángel Lara-González

    2014-12-01

    Full Text Available The methodologies used for the design of the method of sandstones explotation by descending staggered banks using specialized software tools are reported. The data analyzed were collected in the field for the operating license 14816 in Melgar, Tolima. The characterization of the rock mass was held from physical and mechanical tests, performed on cylindrical test tubes in order to obtain the value of the maximum strenght and elastic modulus of the rock. The direction and dip of the sandstone package was rock. The direction and dip of the sandstone package was determined by using the stereographic projection whit DIPS®  software, and the safety factor of the slope was obtained with established banks whit SLIDE® . The slops are 8 meters high and 8 meters wide whit a tilt angle 60°, which generated a safety factor  of 2.1. The design  of the mining method was carried out with GEOVIA SURPAC® , at an early stage of development ascending to the level 11 of the exploitation, to then start mining in descending order to control the stabiLity of slopes. The results obtained allow a general methodology for the development of projects to optimize the process of evaluation and selection of mining method by using specialized design tools.

  10. Multi-scale nitrate transport in a sandstone aquifer system under intensive agriculture

    Science.gov (United States)

    Paradis, Daniel; Ballard, Jean-Marc; Lefebvre, René; Savard, Martine M.

    2018-03-01

    Nitrate transport in heterogeneous bedrock aquifers is influenced by mechanisms that operate at different spatial and temporal scales. To understand these mechanisms in a fractured sandstone aquifer with high porosity, a groundwater-flow and nitrate transport model—reproducing multiple hydraulic and chemical targets—was developed to explain the actual nitrate contamination observed in groundwater and surface water in a study area on Prince Edward Island, Canada. Simulations show that nitrate is leached to the aquifer year-round, with 61% coming from untransformed and transformed organic sources originating from fertilizers and manure. This nitrate reaches the more permeable shallow aquifer through fractures in weathered sandstone that represent only 1% of the total porosity (17%). Some of the nitrate reaches the underlying aquifer, which is less active in terms of groundwater flow, but most of it is drained to the main river. The river-water quality is controlled by the nitrate input from the shallow aquifer. Groundwater in the underlying aquifer, which has long residence times, is also largely influenced by the diffusion of nitrate in the porous sandstone matrix. Consequently, following a change of fertilizer application practices, water quality in domestic wells and the river would change rapidly due to the level of nitrate found in fractures, but a lag time of up to 20 years would be necessary to reach a steady level due to diffusion. This demonstrates the importance of understanding nitrate transport mechanisms when designing effective agricultural and water management plans to improve water quality.

  11. Geology of groundwater occurrences of the Lower Cretaceus sandstone aquifer in East Central Sinai, Egypt

    Directory of Open Access Journals (Sweden)

    Saad Younes Ghoubachi

    2017-01-01

    Full Text Available The present study focused on investigating the impact of geological setting on the groundwater occurrences of the Lower Cretaceous sandstone aquifer (Malha. The Lower Cretaceous sandstone aquifer is subdivided into 3 units according to their lithological characters for the first time in this present work. The study area is dissected by normal faults with their downthrown sides due north direction. The groundwater flows from southeast recharge area (outcrop to the northwest direction with an average hydraulic gradient of 0.0035. The hydraulic parameters of the Lower Cretaceous sandstone aquifer were determined and evaluated through 7 pumping tests carried out on productive wells. The Lower Cretaceous aquifer in the study area is characterized by moderate to high potential. The calculated groundwater volume of the Lower Cretaceous aquifer (6300 km2 in the study area attains about 300 bcm, while the estimated recharge to the same aquifer reaches about 44,500 m3/day with an annual recharge of 16 mcm/year. Expended Durov diagram plot revealed that the groundwater has been evolved from Mg-SO4 and Mg-Cl dissolution area types that eventually reached a final stage of evolution represented by a Na-Cl water type. This diagram helps also in identifying groundwater flow direction. The groundwater salinity ranges from 1082 ppm (Shaira to 1719 ppm (Nakhl, in the direction of groundwater movement towards north.

  12. Thermal reduction and U-recovery from uraniferous phosphorite concentrate of phosphatic sandstone deposit of G. Qatrani, western desert, Egypt

    International Nuclear Information System (INIS)

    Abdel Monem, H.M.

    1988-01-01

    The produced uraniferous phosphorite concentrate from cationic floatation of phosphatic sandstone of G. Qatrani contain 32.01% P 2 O 5 , 0.39% eU and 5.65% SiO 2 . Thermal reduction technique using a high calorific hydrocarbon (Mazout) is used to recover U and P 2 O 5 . At elevated temperature ranging from 500 to 800 0 C, reducing gases mainly, Co are evolved due to mazout cracking; beside a carbon film is precipitated around the treated phosphate grains. These conditions have proved quite beneficial in reducing U+6 into U+4, as well as creating a sufficiently low redox potential below 350 mV in the subsequent leach solution. The effect of different relevant factors are studied and optimized as 700 C, 30 minutes and 20% (wt/wt) ratio for reducing temperature, duration time and amount of reductant added respectively. Hydrochloric acid of 8 N appears to offer the best potential for acidulation of the reduced phosphates at room temperature (25 0 C) and 30 minutes retention time of agitation leaching. The results showed that, more than 98% of P 2 O 5 reports in solution as phosphoric acid and about 97% of uranium is retained in an insoluble form (U+4). Applying oxidizing roast of the leached reduced materials at 800 0 C in the presence of 2% NaCl, would result in both removing the carbon content and oxidizing the contained U+4 to U+6. By subsequent leaching with dilute acidic solution (2N HCl) more than 98% of the contained U+6 is readily soluble

  13. Multielement statistical evidence for uraniferous hydrothermal activity in sandstones overlying the Phoenix uranium deposit, Athabasca Basin, Canada

    Science.gov (United States)

    Chen, Shishi; Hattori, Keiko; Grunsky, Eric C.

    2018-04-01

    The Phoenix U deposit, with indicated resources of 70.2 M lb U3O8, occurs along the unconformity between the Proterozoic Athabasca Group sandstones and the crystalline basement rocks. Principal component analysis (PCA) is applied to the compositions of sandstones overlying the deposit. Among PCs, PC1 accounts for the largest variability of U and shows a positive association of U with rare earth elements (REEs) + Y + Cu + B + Na + Mg + Ni + Be. The evidence suggests that U was dispersed into sandstones together with these elements during the uraniferous hydrothermal activity. Uranium shows an inverse association with Zr, Hf, Th, Fe, and Ti. Since they are common in detrital heavy minerals, such heavy minerals are not the major host of U. The elements positively associated with U are high in concentrations above the deposit, forming a "chimney-like" or "hump-like" distribution in a vertical section. Their enrichment patterns are explained by the ascent of basement fluids through faults to sandstones and the circulation of basinal fluids around the deposit. The Pb isotope compositions of whole rocks are similar to expected values calculated from the concentrations of U, Th, and Pb except for sandstones close to the deposit. The data suggest that in situ decay of U and Th is responsible for the Pb isotope compositions of most sandstones and that highly radiogenic Pb dispersed from the deposit to the proximal sandstones long after the mineralization. This secondary dispersion is captured in PC8, which has low eigenvalue. The data suggests that the secondary dispersion has minor effect on the overall lithogeochemistry of sandstones.

  14. Application of anatectic mineralization to prospecting in-situ leachable sandstone type uranium ore in South Songliao Basin

    International Nuclear Information System (INIS)

    Zhao Zhonghua

    2001-01-01

    The deep ore-forming origin is a new theory for prospecting in-situ leachable sandstone type uranium. Tectonics, lithologic and geochemistry are basic forecasting criteria. Previous unconsolidated sand, source area and geochemical barrier are three essential conditions for forming uranium deposit. Metallogenic environment and prospective region are found. Tertiary system is prospective layer for prospecting in-situ leachable sandstone type uranium ore in south Songliao Basin

  15. Diagenesis and reservoir quality of the Lower Cretaceous Quantou Formation tight sandstones in the southern Songliao Basin, China

    Science.gov (United States)

    Xi, Kelai; Cao, Yingchang; Jahren, Jens; Zhu, Rukai; Bjørlykke, Knut; Haile, Beyene Girma; Zheng, Lijing; Hellevang, Helge

    2015-12-01

    The Lower Cretaceous Quantou Formation in the southern Songliao Basin is the typical tight oil sandstone in China. For effective exploration, appraisal and production from such a tight oil sandstone, the diagenesis and reservoir quality must be thoroughly studied first. The tight oil sandstone has been examined by a variety of methods, including core and thin section observation, XRD, SEM, CL, fluorescence, electron probing analysis, fluid inclusion and isotope testing and quantitative determination of reservoir properties. The sandstones are mostly lithic arkoses and feldspathic litharenites with fine to medium grain size and moderate to good sorting. The sandstones are dominated by feldspar, quartz, and volcanic rock fragments showing various stages of disintegration. The reservoir properties are quite poor, with low porosity (average 8.54%) and permeability (average 0.493 mD), small pore-throat radius (average 0.206 μm) and high displacement pressure (mostly higher than 1 MPa). The tight sandstone reservoirs have undergone significant diagenetic alterations such as compaction, feldspar dissolution, quartz cementation, carbonate cementation (mainly ferrocalcite and ankerite) and clay mineral alteration. As to the onset time, the oil emplacement was prior to the carbonate cementation but posterior to the quartz cementation and feldspar dissolution. The smectite to illite reaction and pressure solution at stylolites provide a most important silica sources for quartz cementation. Carbonate cements increase towards interbedded mudstones. Mechanical compaction has played a more important role than cementation in destroying the reservoir quality of the K1q4 sandstone reservoirs. Mixed-layer illite/smectite and illite reduced the porosity and permeability significantly, while chlorite preserved the porosity and permeability since it tends to be oil wet so that later carbonate cementation can be inhibited to some extent. It is likely that the oil emplacement occurred

  16. The analyzing stratum formation and sediment environment using TEM for finding sandstone type uranium deposits in Mahuangquan area

    International Nuclear Information System (INIS)

    Zhao Xigang; He Jianguo; Zhao Cuiping; Lou Hansheng

    2010-01-01

    Transient electromagnetic method (TEM) is used to detect deep geological information for insidious sandstone type uranium deposits in Mahuangquan area. TEM surveying data is processed to build the relation between resistance rate and different petrology, to ensure three large electronic strata, and to explain the space position of sediment center and alluvial fan. Combining with ore control factors of sandstone type uranium deposit, it can conclude that the slope area and the alluvial fan are the key areas for further exploration work. (authors)

  17. The Collyhurst Sandstone as a secondary storage unit for CCS in the East Irish Sea Basin (UK)

    Science.gov (United States)

    Gamboa, D.; Williams, J. D. O.; Kirk, K.; Gent, C. M. A.; Bentham, M.; Schofield, D. I.

    2016-12-01

    Carbon Capture and Storage (CCS) is key technology for low-carbon energy and industry. The UK hosts a large CO2 storage potential offshore with an estimated capacity of 78 Gt. The East Irish Sea Basin (EISB) is the key area for CCS in the western UK, with a CO2 storage potential of 1.7 Gt in hydrocarbon fields and in saline aquifers within the Triassic Sherwood Sandstone Formation. However, this theoretical storage capacity does not consider the secondary storage potential in the lower Permian Collyhurst Sandstone Formation. 3D seismic data were used to characterise the Collyhurst Sandstone Formation in the EISB. On the southern basin domain, numerous fault-bound blocks limit the lateral continuity of the sandstone strata, while on the northern domain the sandstones are intersected by less faults. The caprock for the Collyhurst sandstones is variable. The Manchester Marls predominate in the south, transitioning to the St. Bees evaporites towards the north. The evaporites in the EISB cause overburden faults to terminate or detach along Upper Permian strata, limiting the deformation of the underlying reservoir units. Five main storage closures have been identified in the Permian strata. In the southern and central area these are predominantly fault bounded, occurring at depths over 1000m. Despite the higher Collyhurst sandstone thickness in the southern IESB, the dolomitic nature of the caprock constitutes a storage risk in this area. Closures in the northern area are deeper (around 2000-2500m) and wider, reaching areas of 34Km2, and are overlain by evaporitic caprocks. The larger Collyhurst closures to the north underlie large Triassic fields with high storage potential. The spatial overlap favours storage plans including secondary storage units in the EISB. The results of this work also expand the understanding of prospective areas for CO2 sequestration in the East Irish Sea Basin in locations where the primary Sherwood Sandstone Formation is either too shallow

  18. Interpreting Fracture Patterns in Sandstones Interbedded with Ductile Strata at the Salt Valley Anticline, Arches National Park, Utah

    OpenAIRE

    Lorenz, John C.; Cooper, Scott P.

    2001-01-01

    Sandstones that overlie or that are interbedded with evaporitic or other ductile strata commonly contain numerous localized domains of fractures, each covering an area of a few square miles. Fractures within the Entrada Sandstone at the Salt Valley Anticline are associated with salt mobility within the underlying Paradox Formation. The fracture relationships observed at Salt Valley (along with examples from Paleozoic strata at the southern edge of the Holbrook basin in northeastern Arizona, a...

  19. Open hardware for open science

    CERN Multimedia

    CERN Bulletin

    2011-01-01

    Inspired by the open source software movement, the Open Hardware Repository was created to enable hardware developers to share the results of their R&D activities. The recently published CERN Open Hardware Licence offers the legal framework to support this knowledge and technology exchange.   Two years ago, a group of electronics designers led by Javier Serrano, a CERN engineer, working in experimental physics laboratories created the Open Hardware Repository (OHR). This project was initiated in order to facilitate the exchange of hardware designs across the community in line with the ideals of “open science”. The main objectives include avoiding duplication of effort by sharing results across different teams that might be working on the same need. “For hardware developers, the advantages of open hardware are numerous. For example, it is a great learning tool for technologies some developers would not otherwise master, and it avoids unnecessary work if someone ha...

  20. Experimental Investigation on Hydraulic Properties of Granular Sandstone and Mudstone Mixtures

    Directory of Open Access Journals (Sweden)

    Dan Ma

    2018-01-01

    Full Text Available The caved zone during longwall mining has high permeability, resulting in a mass of groundwater storage which causes a threat of groundwater inrush hazard to the safe mining. To investigate the hazard mechanism of granular sandstone and mudstone mixture (SMM in caved zone, this paper presents an experimental study on the effect of sandstone particle (SP and mudstone particle (MP weight ratio on the non-Darcy hydraulic properties evolution. A self-designed granular rock seepage experimental equipment has been applied to conduct the experiments. The variation of particle size distribution was induced by loading and water seepage during the test, which indicated that the particle crushing and erosion properties of mudstone were higher than those of sandstone. Porosity evolution of SMM was strongly influenced by loading (sample height and SP/MP weight ratio. The sample with higher sample height and higher weight ratio of SP achieved higher porosity value. In particular, a non-Darcy equation, for hydraulic properties (permeability κ and non-Darcy coefficient ζ calculation, was sufficient to fit the relation between the hydraulic gradient and seepage velocity. The test results indicated that, due to the absence and narrowing of fracture and void during loading, the permeability κ decreases and the non-Darcy coefficient ζ increases. The variation of the hydraulic properties of the sample within the same particle size and SP/MP weight ratio indicated that groundwater inrush hazard showed a higher probability of occurrence in sandstone strata and crushed zone (e.g., faults. Moreover, isolated fractures and voids were able to achieve the changeover from self-extension to interconnection at the last loading stage, which caused the fluctuation tendency of κ and ζ. Fluctuation ability in mudstone was higher than that in sandstone. The performance of an empirical model was also investigated for the non-Darcy hydraulic properties evolution prediction of

  1. Diagenetic history of the Surma Group sandstones (Miocene) in the Surma Basin, Bangladesh

    Science.gov (United States)

    Rahman, M. Julleh Jalalur; McCann, Tom

    2012-02-01

    This study examines the various diagenetic controls of the Miocene Surma Group sandstones encountered in petroleum exploration wells from the Surma Basin, which is situated in the northeastern part of the Bengal Basin, Bangladesh. The principal diagenetic minerals/cements in the Surma Group sandstones are Fe-carbonates (with Fe-calcite dominating), quartz overgrowths and authigenic clays (predominantly chlorite, illite-smectite and minor kaolin). The isotopic composition of the carbonate cement revealed a narrow range of δ 18O values (-10.3‰ to -12.4‰) and a wide range of δ 13C value (+1.4‰ to -23.1‰). The δ 13C VPDB and δ 18O VPDB values of the carbonate cements reveal that carbon was most likely derived from the thermal maturation of organic matter during burial, as well as from the dissolution of isolated carbonate clasts and precipitated from mixed marine-meteoric pore waters. The relationship between the intergranular volume (IGV) versus cement volume indicates that compaction played a more significant role than cementation in destroying the primary porosity. However, cementation also played a major role in drastically reducing porosity and permeability in sandstones with poikilotopic, pore-filling blocky cements formed in early to intermediate and deep burial areas. In addition to Fe-carbonate cements, various clay minerals including illite-smectite and chlorite occur as pore-filling and pore-lining authigenic phases. Significant secondary porosity has been generated at depths from 2500 m to 4728 m. The best reservoir rocks found at depths of 2500-3300 m are well sorted, relatively coarse grained; more loosely packed and better rounded sandstones having good porosities (20-30%) and high permeabilities (12-6000 mD). These good quality reservoir rocks are, however, not uniformly distributed and can be considered to be compartmentalized as a result of interbedding with sandstone layers of low to moderate porosities, low permeabilities owing to poor

  2. Structural diagenesis in Upper Carboniferous tight gas sandstones. Lessons learned from the Piesberg analog study

    Energy Technology Data Exchange (ETDEWEB)

    Steindorf, P.; Hoehne, M.; Becker, S.; Hilgers, C. [RWTH Aachen Univ. (Germany). Energy and Mineral Resources Group (EMR); Koehrer, B. [Wintershall Holding GmbH, Barnstorf (Germany)

    2013-08-01

    Upper Carboniferous tight gas sandstone reservoirs in NW-Germany consist of thick successions of cyclothems. Our focus is the Westphalian D of the Piesberg quarry near Osnabrueck, which exposes cemented, faulted and jointed third-order coarse- to fine-grained sandstone cycles separated by anthracite coal seams. We characterize the rocks and the lateral variation of rock properties such as porosity to better constrain input data for reservoir modelling. Three cycles are exposed, each approximately 50 m thick. Rock types can be clearly distinguished by spectral gamma ray in the quarry. Sandstones are intensely compacted and cemented with quartz and generally characterized by low porosities < 8 % (Hepycnometry on plugs and cuttings). Porosities are secondary and mainly related to detrital carbonate dissolution. Around faults dissolution is higher and the porosities can increase to up to 25%. The normal faults show different throws in the quarry and bands of shale and coal have smeared into the fault at juxtaposed beds, which may result in compartments. They dominantly strike W-E and NNW-SSE, but subordinate NE-SW striking fault patterns are also present. Joints were analyzed in a 50 x 50 m section of the quarry wall using Lidar (Light detection and ranging) laser scanning, which allows the characterization of the lithology and quantitative measurement of bedding and fracture orientation data in inaccessible areas. NNE-SSW and W-E joint sets are accompanied by northeasterly and northwesterly striking sets. Around faults, fault planes and fractures are cemented with quartz veins, showing localized mass transport. Due to the intense cementation, the sandstones can reach uniaxial strengths of more than 100 MPa normal to bedding, and approximately 50 MPa parallel to bedding. Sandstone beds within and close to faults are leached by fluids, and their uniaxial strength is reduced by a factor of more than two. Our high resolution field data enables a better understanding of

  3. Open Access

    Science.gov (United States)

    Suber, Peter

    2012-01-01

    The Internet lets us share perfect copies of our work with a worldwide audience at virtually no cost. We take advantage of this revolutionary opportunity when we make our work "open access": digital, online, free of charge, and free of most copyright and licensing restrictions. Open access is made possible by the Internet and copyright-holder…

  4. Open innovation

    DEFF Research Database (Denmark)

    Bogers, Marcel; Chesbrough, Henry; Moedas, Carlos

    2018-01-01

    Open innovation is now a widely used concept in academia, business, and policy making. This article describes the state of open innovation at the intersection of research, practice, and policy. It discusses some key trends (e.g., digital transformation), challenges (e.g., uncertainty...

  5. Pulsed molecular beams: A lower limit on pulse duration for fully developed supersonic expansions

    International Nuclear Information System (INIS)

    Saenger, K.L.

    1981-01-01

    We derive an expression for Δt/sub min/, the mimimum pulse duration (''valve open time'') required if a pulsed nozzle is to produce a supersonic beam comparably ''cold'' to that obtained from a continuous source

  6. Quantitative mineralogical analysis of sandstones using x-ray diffraction techniques

    International Nuclear Information System (INIS)

    Ward, C.R.; Taylor, J.C.

    1999-01-01

    Full text: X-ray diffraction has long been used as a definitive technique for mineral identification based on the measuring the internal atomic or crystal structures present in powdered rocks; soils and other mineral mixtures. Recent developments in data gathering and processing, however, have provided an improved basis for its use as a quantitative tool, determining not only the nature of the minerals but also the relative proportions of the different minerals present. The mineralogy of a series of sandstone samples from the Sydney and Bowen Basins of eastern Australia has been evaluated by X-ray diffraction (XRD) on a quantitative basis using the Australian-developed SIROQUANT data processing technique. Based on Rietveld principles, this technique generates a synthetic X-ray diffractogram by adjusting and combining full-profile patterns of minerals nominated as being present in the sample and interactively matches the synthetic diffractogram under operator instructions to the observed diffractogram of the sample being analysed. The individual mineral patterns may be refined in the process, to allow for variations in crystal structure of individual components or for factors such as preferred orientation in the sample mount. The resulting output provides mass percentages of the different minerals in the mixture, and an estimate of the error associated with each individual percentage determination. The chemical composition of the mineral mixtures indicated by SIROQUANT for each individual sandstone studied was estimated using a spreadsheet routine, and the indicated proportion of each oxide in each sample compared to the actual chemical analysis of the same sandstone as determined independently by X-ray fluorescence spectrometry. The results show a high level of agreement for all major chemical constituents, indicating consistency between the SIROQUANT XRD data and the whole-rock chemical composition. Supplementary testing with a synthetic corundum spike further

  7. Unemployment duration and unemployment insurance

    DEFF Research Database (Denmark)

    Røed, Knut; Jensen, Peter; Thoursie, Anna

    2008-01-01

    Based on pooled register data from Norway and Sweden, we find that differences in unemployment duration patterns reflect dissimilarities in unemployment insurance (UI) systems in a way that convincingly establishes the link between economic incentives and job search behaviour. Specifically, UI...... benefits are relatively more generous for low-income workers in Sweden than in Norway, leading to relatively longer unemployment spells for low-income workers in Sweden. Based on the between-countries variation in replacement ratios, we find that the elasticity of the outflow rate from insured unemployment...

  8. Provenance, diagenesis, tectonic setting and reservoir quality of the sandstones of the Kareem Formation, Gulf of Suez, Egypt

    Science.gov (United States)

    Zaid, Samir M.

    2013-09-01

    The Middle Miocene Kareem sandstones are important oil reservoirs in the southwestern part of the Gulf of Suez basin, Egypt. However, their diagenesis and provenance and their impact on reservoir quality, are virtually unknown. Samples from the Zeit Bay Oil Field, and the East Zeit Oil Field represent the Lower Kareem (Rahmi Member) and the Upper Kareem (Shagar Member), were studied using a combination of petrographic, mineralogical and geochemical techniques. The Lower Rahmi sandstones have an average framework composition of Q95F3.4R1.6, and 90% of the quartz grains are monocrystalline. By contrast, the Upper Shagar sandstones are only slightly less quartzose with an average framework composition of Q76F21R3 and 82% of the quartz grains are monocrystalline. The Kareem sandstones are mostly quartzarenite with subordinate subarkose and arkose. Petrographical and geochemical data of sandstones indicate that they were derived from granitic and metamorphic terrains as the main source rock with a subordinate quartzose recycled sedimentary rocks and deposited in a passive continental margin of a syn rift basin. The sandstones of the Kareem Formation show upward decrease in maturity. Petrographic study revealed that dolomite is the dominant cement and generally occurs as fine to medium rhombs pore occluding phase and locally as a grain replacive phase. Authigenic quartz occurs as small euhedral crystals, locally as large pyramidal crystals in the primary pores. Authigenic anhydrites typically occur as poikilotopic rhombs or elongate laths infilling pores but also as vein filling cement. The kaolinite is a by-product of feldspar leaching in the presence of acidic fluid produced during the maturation of organic matter in the adjacent Miocene rocks. Diagenetic features include compaction; dolomite, silica and anhydrite cementation with minor iron-oxide, illite, kaolinite and pyrite cements; dissolution of feldspars, rock fragments. Silica dissolution, grain replacement and

  9. National uranium resource evaluation. Geology and recognition criteria for sandstone uranium deposits of the salt wash type, Colorado Plateau Province. Final report

    International Nuclear Information System (INIS)

    Thamm, J.K.; Kovschak, A.A. Jr.; Adams, S.S.

    1981-01-01

    The uranium-vanadium deposits of the Salt Wash Member of the Morrison Formation in the Colorado Plateau are similar to sandstone uranium deposits elsewhere in the USA. The differences between Salt Wash deposits and other sandstone uranium deposits are also significant. The Salt Wash deposits are unique among sandstone deposits in that they are dominantly vanadium deposits with accessory uranium. The Salt Wash ores generally occur entirely within reduced sandstone, without adjacent tongues of oxidized sandstone. They are more like the deposits of Grants, which similarly occur in reduced sandstones. Recent studies of the Grants deposits have identified alteration assemblages which are asymmetrically distributed about the deposits and provide a basis for a genetic model for those deposits. The alteration types recognized by Shawe in the Slick Rock district may provide similar constraints on ore formation when expanded to broader areas and more complete chemical analyses

  10. Petrographic characteristic of the sandstones of the upper paleocene-middle eocene aged in the Yildizli-Aydinkent (Ereğli-Konya area

    Directory of Open Access Journals (Sweden)

    A. Müjdat Özkan

    2002-03-01

    Full Text Available In the study area, Upper Paleocene - Middle Eocene aged Halkapınar formation, was formed in a shallow and deep marine environment. The lithologies of this formation are medium - thick bedded conglomerate, thin - thick bedded sandstone, thin - very thick bedded shale, thin - medium bedded marl with chert nodules and bands. In addition olistolithes of ophiolitic melange are found at the top of the sandstones, which includes basalt interbands. Yellowish gray, greenish gray, beige, gray colored sandstones include some sedimentary structures, namely ripple - marks, graded bedding, laminate, convolute lamination, current ripple, tool marks. Constituents of the sandstones are quartz, plagioclase, sanidine, orthoclase, fragments of sedimentary and methamorphic rocks, biotite, muscovite, opaque mineral and glauconite. The sandstones, which are not matured in terms of mineralogy and texture, are mainly cemented by calcite, clay matrix and minor iron oxide and glauconite matrix. The sandstones are named lithic arenite, lithic graywacke, feldspathic litharenite and litharenite.

  11. Open Bibliography

    OpenAIRE

    Murray-Rust, Peter; Pollock, Rufus; MacGillivray, Mark; O'Steen, Ben; Waites, William

    2011-01-01

    Poster presented at the VSMF Symposium held at the Unilever Centre on 2011-01-17. More research is published currently than can be understood or followed by a researcher without the aid of a computer. We need Open shareable information on research publications, an Open Bibliography, to build the services that enable researchers to explore their field and discover the research they need. Producers of bibliographic data such as libraries, publishers, universities, scholars or social referenc...

  12. Open IS

    DEFF Research Database (Denmark)

    Germonprez, Matt; Crowston, Kevin; Avital, Michel

    2013-01-01

    The collective intelligence and collective action of “open” communities have produced a variety of complex knowledge goods and radical social change. The Information Systems (IS) community has invested significant effort into researching open communities and the ecosystems in which they operate...... therefore seeks to stimulate a thoughtful and dynamic discussion around the proposition that becoming a more open community will enhance the IS discipline’s scholarly inquiry and global impact....

  13. Gallbladder removal - open

    Science.gov (United States)

    Cholecystectomy - open; Gallbladder - open cholecystectomy; Cholecystitis - open cholecystectomy; Gallstones - open cholecystectomy ... a medical instrument called a laparoscope ( laparoscopic ... Open gallbladder surgery is used when laparoscopic surgery cannot ...

  14. Utilisation of Sand from Kaolin Washing for the Manufacture of Alkali-activated Artificial Sandstone

    Science.gov (United States)

    Vavro, Martin; Vavro, Leona; Mec, Pavel; Soucek, Kamil; Pticen, Frantisek; Reiterman, Pavel

    2017-04-01

    Sandstones represent a traditional natural stones which are widely used in Czech architecture and sculpture over a long time. Thanks to their relatively easy workability, sandstones provide a wide range of stone products and also represent a popular material for architectural and sculptural purposes. In the field of restoration of artworks, they are therefore often used for manufacturing stone statue copies originally made from the same or similar type of stone. Despite a relatively common and varied occurrence of natural sandstones, the method of the artificial stone facsimiles creation in the form of various cast elements is also often applied in restoration practice. The history of application of artificial stones in civil engineering and architecture goes back to the ancient times, i.e. to Roman antiquity and possibly up to the time of ancient Egypt. The lack of appropriate natural rock, suitable in the view of colour, grain size or texture is the main reason of manufacturing copies based on synthetic mixtures. The other reason is high financial costs to create a sculpture copy from natural materials. Mixtures made from white and/or grey cements, sands, carefully selected crushed stone or well graded natural gravels, and mineral coloring pigments or mixtures with acrylate, polyester, and epoxy resins binder are the most frequently used artificial materials for cast stone manufacturing. This paper aims to bring information about composition and properties of artificial sandstones made from alkali-activated binder mixtures based on metakaolin and granulated blast furnace slag. The filler of this artificial stone is represented by fine-grained sand generated during kaolin wet processing. Used sand is mainly formed by quartz, feldspars, micas (muscovite > biotite), residual kaolin, and to a lesser extent also by Fe oxyhydroxides ("limonite"), titanium dioxide mineral (probably anatase), and carbonate mineral unidentified in detail. Annual Czech production of this

  15. The mineralogical composition of sandstone and its effect on sulphur dioxide deposition

    Directory of Open Access Journals (Sweden)

    Müller, Urs

    2008-06-01

    Full Text Available Air pollutants often accelerate stone deterioration in historical buildings and monuments in urban areas. The pollutants are themselves the products of fossil fuel combustion and intensive farming. While this trend seems to have been curbed by strict emission laws in the European Union, in most developing and emerging countries air pollution is an ongoing process due to increasing energy needs and vehicle traffic. Many factors condition natural stone behaviour with respect to gaseous pollutants. Two of the more prominent of such factors are the composition of the atmosphere and the type of stone. Due to their porosity, sandstones are particularly vulnerable to air pollutant attack. Many of the reactions between non-carbonaceous sandstones and these gases are not well understood, however. The present study aimed to acquire an understanding of the processes and factors governing sandstone behaviour when exposed to sulphur dioxide. Seven different sandstones from southern and eastern Germany were analyzed for the study. The binder composition of the stones varied significantly. They also exhibited completely different behaviour in connection with SO2 sorption. Interestingly, while the amount of SO2 deposited was unrelated to the specific surface area of the sandstones, this parameter was closely correlated to the iron oxide content. Iron oxide phases are believed to act as a catalyst in the oxidation of SO2 to SO3. The type and amount of clay mineral, in turn, was found to have no significant impact on initial SO2 deposition in sandstones.Los contaminantes atmosféricos son con frecuencia responsables de la aceleración de la degradación de la piedra en los edificios y monumentos históricos de las zonas urbanas. Los contaminantes en sí son productos de reacción procedentes de la combustión de los hidrocarburos y de la agricultura intensiva. Dentro de la Comunidad Europea, el avance parece haberse ralentizado mediante restrictivas leyes sobre

  16. Microbial mat structures in profile: The Neoproterozoic Sonia Sandstone, Rajasthan, India

    Science.gov (United States)

    Samanta, Pradip; Mukhopadhyay, Soumik; Mondal, Anudeb; Sarkar, Subir

    2011-01-01

    Ubiquitous microorganisms, especially cyanobacteria preferably grow on the sediment surface thereby producing microbial mats. In the absence of grazers and bioturbators, microbial mat is a unique feature of the Proterozoic. Most of the papers so far published described a wide variety of bed surface microbial mat structures with rare illustrations from sections perpendicular to bedding. Nonetheless, bed surface exposures are relatively rare in rock records. This limitation of bed surface exposures in rock records suggest that a study of microbial mats in bed-across sections is needed. The 60 m thick coastal marine interval of the Sonia Sandstone Formation is bounded between two terrestrial intervals, a transgressive lag at the base and an unconformity at the top, and has been chosen for exploration of microbial mat structures in bed-across sections. A wide variety of microbial mat-induced structures in bed-across sections are preserved within the coastal interval of the Sonia Sandstone. Though many of these structures are similar in some aspects with bed surface structures, some of those presented here are new. The palaeogeographic range of these microbial structures extends from supralittoral to neritic. Diagenetic alterations of microbial mats produce pyrite and those zones are suitable for the preservation of microbial remains. SEM and EDAX analyses show fossil preservation of filamentous microbial remains that confirm the presence of microbial mats within the coastal interval of the Sonia Sandstone. Effects of proliferation of microbial mats in the siliciclastic depositional setting are numerous. The mat-cover on sediment surfaces hinders reworking and/or erosion of the sediments thereby increases the net sedimentation rate. Successive deposition and preservation of thick microbial mat layer under reducing environments should have a great potential for hydrocarbon production and preservation and therefore these Proterozoic formations could be a target for

  17. Blueberries on Earth and Mars: Correlations Between Concretions in Navajo Sandstone and Terra Meridiani on Mars.

    Science.gov (United States)

    Mahaney, W. C.; Milner, M. W.; Netoff, D.; Dohm, J.; Kalm, V.; Krinsley, D.; Sodhi, R. N.; Anderson, R. C.; Boccia, S.; Malloch, D.; Kapran, B.; Havics, A.

    2008-12-01

    Concretionary Fe-Mn-rich nodular authigenic constituents of Jurassic Navajo sandstone (moki marbles) bear a certain relationship to similar concretionary forms ('blueberries') observed on Mars. Their origin on Earth is considered to invoke variable redox conditions with underground fluids penetrating porous quartz-rich sandstone leading to precipitation of hematite and goethite-rich material from solution, generally forming around a central nucleus of fine particles of quartz and orthoclase, recently verified by XRD and SEM-EDS analyses. At the outer rim/inner nucleus boundary, bulbous lobes of fine-grained quartz often invade and fracture the outer rim armored matrix. The bulbous forms are interpreted to result from fluid explusion from the inner concretionary mass, a response to pressure changes accompanying overburden loading. Moki marbles, harder than enclosing rock, often weather out of in situ sandstone outcrops that form a surface lag deposit of varnished marbles that locally resemble desert pavement. The marbles appear morphologically similar to 'blueberries' identified on the martian surface in Terra Meridiani through the MER-1 Opportunity rover. On Earth, redox fluids responsible for the genesis of marbles may have emanated from deep in the crust (often influenced by magmatic processes). These fluids, cooling to ambient temperatures, may have played a role in the genesis of the cemented outer rim of the concretions. The low frequency of fungi filaments in the marbles, contrasts with a high occurrence in Fe-encrusted sands of the Navajo formation [1], indicating that microbial content is of secondary importance in marble genesis relative to the fluctuating influx of ambient groundwater. Nevertheless, the presence of filaments in terrestrial concretions hints at the possibility of discovering fossil/extant life on Mars, and thus should be considered as prime targets for future reconnaissance missions to Mars. 1] Mahaney, W.C., et al. (2004), Icarus, 171, 39-53.

  18. Research and application of information system for sandstone-type uranium exploration

    International Nuclear Information System (INIS)

    Han Shaoyang; Huang Shutao; Hou Huiqun

    2003-01-01

    The GIS (Geographical Information System) technique is applied to the exploration and evaluation of in-situ leachable sandstone-type uranium deposits and the GIS application system of desktop is created for non-GIS professionals. ArcView3.2 is taken as compositive platform of the information system. The secondary design is developed through the AVENUE language provided by ArcView3.2 on the software functions. According to the needs of multi-source information management and integrated evaluation, a series of new functions are appended to the basic platform through AVENUE language on a basis of sufficiently inheriting ArcView3.2 software functions and a friendly graphic user interface is also created, so that the system implements the following functions better, including information query, data base management, editing graphics, geologic mapping, image processing, spatial analysis, model analysis and result output. In order to manage the plenty of borehole data better and quickly realize the borehole mapping, a system software of borehole data management and mapping on the base of GIS software platform is developed. The system software has been applied to uranium survey project in the west of Hailaer basin. Based on multi-source geoscience information database including geologic, geophysical, geochemical and remote sensing data, the system software has been used to perform the integrated analysis of spatial data for realizing the deep analysis and studies of the metallogenic geologic environments of sandstone-type uranium deposits. In the Kelulun basin, the weights of evidence analysis have been used to quantitatively predict the prospective areas of sandstone uranium deposits. Information system has also been applied to the integrated evaluation of uranium resource in the south of Yili basin, Songliao basin and other areas. (authors)

  19. High-resolution mapping of yield curve shape and evolution for high porosity sandstones

    Science.gov (United States)

    Bedford, J. D.; Faulkner, D.; Wheeler, J.; Leclere, H.

    2017-12-01

    The onset of permanent inelastic deformation for porous rock is typically defined by a yield curve plotted in P-Q space, where P is the effective mean stress and Q is the differential stress. Sandstones usually have broadly elliptical shaped yield curves, with the low pressure side of the ellipse associated with localized brittle faulting (dilation) and the high pressure side with distributed ductile deformation (compaction). However recent works have shown that these curves might not be perfectly elliptical and that significant evolution in shape occurs with continued deformation. We therefore use a novel stress-probing methodology to map in high-resolution the yield curve shape for Boise and Idaho Gray sandstones (36-38% porosity) and also investigate curve evolution with increasing deformation. The data reveal yield curves with a much flatter geometry than previously recorded for porous sandstone and that the compactive side of the curve is partly comprised of a near vertical limb. The yield curve evolution is found to be strongly dependent on the nature of inelastic strain. Samples that were compacted under a deviatoric load, with a component of inelastic shear strain, were found to have yield curves with peaks that are approximately 50% higher than similar porosity samples that were hydrostatically compacted (i.e. purely volumetric strain). The difference in yield curve evolution along the different loading paths is attributed to mechanical anisotropy that develops during deviatoric loading by the closure of preferentially orientated fractures. Increased shear strain also leads to the formation of a plateau at the peak of the yield curve as samples deform along the deviatoric loading path. These results have important implications for understanding how the strength of porous rock evolves along different stress paths, including during fluid extraction from hydrocarbon reservoirs where the stress state is rarely isotropic.

  20. On the origin of calcite-cemented sandstones in the clearwater formation oil-sands, Alberta

    Energy Technology Data Exchange (ETDEWEB)

    Colquhoun, I.M.

    1999-01-01

    This thesis examined the formation of calcite-cemented sandstones in the Clearwater Formation within the Cold Lake and southern Primrose areas of the Alberta oil sands. Three stages of diagenesis have been recognized, both in the calcite-cemented sandstones and reservoir sands. Diagenesis of the Clearwater Formation in the Cold Lake and southern Primrose areas ended once the reservoir filled with hydrocarbons, but in the Cold Lake area, diagenesis of water-saturated sands likely continued after hydrocarbon emplacement. The reservoir sands in the formation contain a diverse clay mineral assemblage. In general, 0.7 nm clays dominate the diagenetic clay mineralogy of the Clearwater sands. Reservoir sands that contain large amounts of detrital clays and early diagenetic, grain-coating chlorite/smectite have significantly reduced bitumen-saturation. The presence of detrital and diagenetic smectitic clays complicates the removal of bitumen from the Clearwater formation using cyclic steam stimulation techniques because they swell during steam stimulation and reduce porosity and permeability of reservoir sands. Reservoir sands that contain kaolinite, feldspar and calcite react to form smectitic clays, which swell upon cyclic steam stimulation and further reduce porosity and permeability of reservoir sands. However, in the Cold Lake and Primrose areas, the dominant clay mineral is berthierine, which is associated with high calcite, which help to preserve porosity, permeability and bitumen saturation. The porous nature of bitumen-saturated, calcite-cemented sandstones that are laterally extensive could possibly provide a preferential path for steam to initiate calcite dissolution and produce significant concentrations of dissolved carbon dioxide in injected fluids. It was noted that this may then precipitate as carbonate scale within the reservoir and could cause formation damage or affect production equipment. 207 refs., 9 tabs., 58 figs., 3 appendices.

  1. Early Cretaceous marine sediments of the Lower Saxony Basin. The Gildehaus Sandstone

    Energy Technology Data Exchange (ETDEWEB)

    Dellepiane, S.; Weiel, D. [Wintershall Holding GmbH, Barnstorf (Germany); Gerwert, D.; Mutterlose, J. [Bochum Univ. (Germany). Inst. fuer Geologie, Mineralogie und Geophysik

    2013-08-01

    During the Early Cretaceous (Berriasian - Aptian) the Lower Saxony Basin (LSB) formed the southernmost extension of the North Sea Basin. Sedimentation patterns of the LSB were controlled by divergent dextral shear movement causing differential subsidence related to early rifting in the North Sea. Up to 2000m of fine grained mudstones accumulated in the basin centre, while marginal marine, coarser grained siliciclastics were deposited along the western and southern margins of the LSB. The western marginal facies, outcropping along the Dutch-German border, is characterised by shallow marine sandstones of Valanginian - Hauterivian age. These units, which are separated by clay rich intervals, include the Bentheim Sdst., the Dichotomites Sdst., the Grenz Sdst., the Noricum Sdst. and the Gildehaus Sdst. These sandstones form a series of overall backstepping units, controlled by a main transgressive trend. Economically important are the Bentheim Sdst. and the Gildehaus Sdst., with a long oil producing history. The Bentheim Sdst. (early Valanginian) has been interpreted as an overall retrograding unit related to an incised valley infill with material mainly coming from the South. Tidal processes dominated the deposition of the Bentheim Sdst. The origin and genesis of the Gildehaus Sdst. (mid Hauterivian) is, however, less well understood. Here we present data from two wells drilled to the Gildehaus Sdst. (Emlichheim oil field) which provide evidence for a two fold subdivision of the unit. A well sorted massive quartz sandstone is followed by an interval composed of reworked coarse clastics of massflow origin. Micropalaeontological evidence suggests a fully marine, hemi-pelagic origin of the mud dominated matrix throughout the Gildehaus Sdst. These findings indicate a depositional environment quite different from that of the Bentheim Sdst. Short termed pulses of substantial input of clastic material from two different sources in the West to Southwest punctuated the overall

  2. Research and performance evaluation on an HA integrated acid system for sandstone acidizing

    Directory of Open Access Journals (Sweden)

    Liqiang Zhao

    2018-03-01

    Full Text Available When the conventional sandstone acidizing technologies are adopted, many slugs are needed in the injection of prepad fluid, treatment fluid and postpad fluid, and consequently the production and operation suffers inconveniences and difficulties. In view of this, a kind of HA integrated acid system which is mainly composed of organic polybasic acids (HA+HCl + HF and an efficient organic solvent was developed in this paper based on the idea of integrated acid replacing ''multiple steps'' and high efficiency and intensification. Via this HA integrated acid system, the complicated blockage in sandstone reservoirs can be removed effectively. Then, experiments were carried out on this system to evaluate its performance in terms of its retardance, organic blockage dissolution, chelating and precipitation inhibition. It is indicated that this new system can not only realize the acidizing of conventional integrated acid, but also present a good retarding performance by controlling H+ multi-stage ionization step by step and by forming silica acid-aluminum phosphonate film on the surface of clay minerals; that via this new HA integrated acid system, the organic blockage can be removed efficiently; and that it is wider in pH solution range than conventional APCs (aminopolycarboxyliates chelants, stronger in chelating capacity of Ca2+, Mg2+ and Fe3+ than conventional chelants (e.g. EDTA, NTA and DTPA, and better in precipitation inhibition on metal fluoride, fluosilicic acid alkali metal, fluoaluminic acid alkali metal and hydroxide than multi-hydrogen acid, fluoboric acid and mud acid systems. These research results provide a technical support for the plugging removal in high-temperature deep oil and gas reservoirs. Keywords: Organic polybasic acid, Integrated acid, Retardance, Chelating, Precipitation, Acidizing, Sandstone, Reservoir

  3. Sandstone uranium deposits: analogues for surf disposal in some sedimentary rocks

    International Nuclear Information System (INIS)

    Brookins, D.G.

    1987-01-01

    Sandstone uranium deposits are well suited as analogs for SURF. These deposits typically occur as tabular or lensoid masses of uraniferous sandstone, commonly where the argillaceous mineral and organic content is high. Primary minerals consist of pitchblende and/or coffinite, with possibly some urano-organic phases as well. The ore is usually associated with authigenic ferromagnesian clay minerals, such as chlorite and/or authigenic illite and/or mixed layer smectite-illite; and with pyrite ± jordisite ± seleniferrous species ± calcite. Organic matter is usually associated with the ore. The clay minerals in the ore zones are commonly vanadiferrous. The genesis of the sandstone uranium deposits is now fairly well understood and allows semi-quantitative estimates to be placed on behaviour of analog-elements for many constituents of SURF (or HLW). Prior to mineralization, oxidized species of U, V, Se, Mo, As are carried together as oxyanions; these species precipitate in a restricted range of Eh-pH when reducing conditions are met. Concomitant with removal of these species, due to formation of reduced, insoluble species, several other elements of interest are concentrated in the ore zones as well. Chalcophile elements, such as Cu, Co, Mn, Zn, Cd, Sb, and others are fixed in authigenic sulfide phases, and the alkalis Rb, K, and Cs are fixed in the authigenic illite and illitic mixed layer clays. The alkaline earth elements Sr and Ba are commonly fixed in sulfate-rich rock. The rare earth elements (REE) are incorporated into authigenic clay minerals or into oxy-hydroxide phases. (author)

  4. Remote detection of fluid-related diagenetic mineralogical variations in the Wingate Sandstone at different spatial and spectral resolutions

    Science.gov (United States)

    Okyay, Unal; Khan, Shuhab D.

    2016-02-01

    Well-exposed eolian units of the Jurassic system on the Colorado Plateau including the Wingate Sandstone, show prominent color variations throughout southeastern Utah due to diagenetic changes that include precipitation and/or removal of iron oxide, clay, and carbonate cement. Spatially variable characteristic diagenetic changes suggest fluid-rock interactions through the sandstone. Distinctive spectral signatures of diagenetic minerals can be used to map diagenetic mineral variability and possibly fluid-flow pathways. The main objective of this work was to identify characteristic diagenetic minerals, and map their spatial variability from regional to outcrop scale in Wingate Sandstone exposures of Lisbon Valley, Utah. Laboratory reflectance spectroscopy analysis of the samples facilitated identification of diagnostic spectral characteristics of the common diagenetic minerals and their relative abundances between altered and unaltered Wingate Sandstone. Comparison of reflectance spectroscopy with satellite, airborne, and ground-based imaging spectroscopy data provided a method for mapping and evaluating spatial variations of diagenetic minerals. The Feature-oriented Principal Component Selection method was used on Advanced Spaceborne Thermal Emission and Reflection Radiometer data so as to map common mineral groups throughout the broader Wingate Sandstone exposure in the area. The Minimum Noise Fraction and Spectral Angle Mapper methods were applied on airborne HyMap and ground-based hyperspectral imaging data to identify and map mineralogical changes. The satellite and airborne data showed that out of 25.55 km2 total exposure of Wingate Sandstone in Lisbon Valley, unaltered sandstone cover 12.55 km2, and altered sandstone cover 8.90 km2 in the northwest flank and 5.09 km2 in the southern flank of the anticline. The ground-based hyperspectral data demonstrated the ability to identify and map mineral assemblages with two-dimensional lateral continuity on near

  5. The Saint Martin de Belleville syncline and its uraniferous permian sandstone

    International Nuclear Information System (INIS)

    Schade, Johannes

    1983-01-01

    This dissertation (these de specialite) is a study of the geology of the St.Martin d.B. syncline and the uranium prospect 'le Cochet' in the Carboniferous Brianconnais Zone of Savoy. Stratigraphy and sedimentology: This syncline presents continental detrital sediments ranging from U.Carboniferous to L.Triassic. In the U.Carboniferous, magmatic activity begins with the Moriaz Layers acid volcanics that are considered as a lateral equivalent of the Stephanian Courchevel Conglomerates. In Permian times, parts of an alluvial fan seem to occupy the north of the study area (gray and green conglomeratic sandstone). Southwards these inter-finger with flood plain sediments (red slate) including a locally oolitic limestone. Volcanic detritus is important in the Permian. Tourmalinite pebbles are frequent and seem to be related to the regional Permian magmatism. Albitization of feldspars is general in the Carboniferous and the Permian. The Permo-triassic typically shows microcline bearing dolomitic sandstones. In the Scythian quartzites orthoclase is the dominant feldspar. The quartzites are overlain by L.Triassic evaporites identified by the sulfur isotope ratio of their gypsum. The morphology of the zircons in the sandstones has been investigated using the typological method of J.P. Pupin. Regional Permian magmatism apparently produces volcanics of the calc-alkalic and tholeiitic series as well as a high level granitic intrusion of anatectic origin. The uranium occurrences are strata-bound on a kilometric and hecto-metric scale. They are developed almost exclusively in the gray variety of the Permian sandstones whose gray and red varieties are always barren. Within this unit, the mineralization impregnates irregularly distributed lenses and pods of coal material. Uranium is accompanied by vanadium occurring as roscoelite. The association U-V, of bio-philic character, reflects the concentration in the sedimentary environment and argues for a quite indirect relation with the

  6. Analysis on metallogenetic conditions of sandstone-type uranium deposit in Minhe Basin

    International Nuclear Information System (INIS)

    Jiang Minzhong; Wang Huaiwu

    2002-01-01

    Little uranium prospecting has been performed so far in Minhe basin. However, at the marginal areas of the basin uranium mineralizations and lots of aero-radioactive anomalies have been found before, and the basin shows some prospecting potential. Based on the regional geological setting, by means of interpretation of high-precision aero-magnetic, aero-radiometric and Bouguer gravimetric data, and combined with hydrodynamic, lithofacies-palaeographic and paleo-climatic analyses, authors make a comprehensive evaluation of metallogenic conditions for sandstone-type uranium deposits, and propose metallogenically favourable areas in the basin

  7. Seasonal Deep Aquifer Thermal Energy Storage in the Gassum Sandstone Formation

    DEFF Research Database (Denmark)

    Holmslykke, H.D.H.; Kjøller, C.; Fabricius, Ida Lykke

    Seasonal storage of excess heat in hot deep aquifers is considered to optimise the usage of commonly available energy sources. The potential chemical reactions caused by heating the Gassum Sandstone Formation to up to 150°C is investigated by core flooding experiments combined with petrographic...... analysis and geochemical modelling. Synthetic formation water is injected into two sets of Gassum Formation samples at 25°C, 50°C (reservoir temperature), 100°C and 150°C with a velocity of 0.05 PV/hr and 0.1 PV/hr, respectively. A significant increase in the aqueous concentration of silicium and iron...

  8. Petrography of thoriferous hydrocarbon nodules in sandstones, and their significance for petroleum exploration

    International Nuclear Information System (INIS)

    Parnell, J.; Monson, B.; Tosswill, R.J.

    1990-01-01

    Nodules of thorium-rich hydrocarbon are recorded in sandstone sequences from several basins. The hydrocarbon nodules contain mineral inclusions, particularly of thorite or monazite. There is evidence both for accretion of hydrocarbons around detrital heavy mineral grains and for epigenetic growth by interaction of hydrocarbons with thorium-bearing fluids. Both mechanisms depend upon the precipitation of solid hydrocarbons induced by irradiation from thorium. The nodules exhibit aggressive replacement of other grains, a characteristic of radioanomalous hydrocarbons. The occurrence of the nodules is dependent upon an appropriate (plutonic) source for the thorium, but given this constraint they are important evidence for hydrocarbon migration pathways. (author)

  9. Dzhezkazgan and associated sandstone copper deposits of the Chu-Sarysu basin, Central Kazakhstan

    Science.gov (United States)

    Box, Stephen E.; Seltmann, Reimar; Zientek, Michael L.; Syusyura, Boris; Creaser, Robert A.; Dolgopolova, Alla

    2012-01-01

    Sandstone-hosted copper (sandstone Cu) deposits occur within a 200-km reach of the northern Chu-Sarysu basin of central Kazakhstan (Dzhezkazgan and Zhaman-Aibat deposits, and the Zhilandy group of deposits). The deposits consist of Cu sulfide minerals as intergranular cement and grain replacement in 10 ore-bearing members of sandstone and conglomerate within a 600- to 1,000-m thick Pennsylvanian fluvial red-bed sequence. Copper metal content of the deposits ranges from 22 million metric tons (Mt, Dzehzkazgan) to 0.13Mt (Karashoshak in the Zhilandy group), with average grades of 0.85 to 1.7% Cu and significant values for silver (Ag) and rhenium (Re). Broader zones of iron reduction (bleaching) of sandstones and conglomerates of the red-bed sequence extend over 10 km beyond each of the deposits along E-NE-trending anticlines, which began to form in the Pennsylvanian. The bleached zones and organic residues within them are remnants of ormer petroleum fluid accumulations trapped by these anticlines. Deposit sites along these F1anticlines are localized at and adjacent to the intersections of nearly orthogonal N-NW-trending F2synclines. These structural lows served to guide the flow of dense ore brines across the petroleum-bearing anticlines, resulting in ore sulfide precipitation where the two fluids mixed. The ore brine was sourced either from the overlying Early Permian lacustrine evaporitic basin, whose depocenter occurs between the major deposits, or from underlying Upper Devonian marine evaporites. Sulfur isotopes indicate biologic reduction of sulfate but do not resolve whether the sulfate was contributed from the brine or from the petroleum fluids. New Re-Os age dates of Cu sulfides from the Dzhezkazgan deposit indicate that mineralization took place between 299 to 309 Ma near the Pennsylvanian-Permian age boundary. At the Dzhezkazgan and some Zhilandy deposits, F2fold deformation continued after ore deposition. Copper orebodies in Lower Permian

  10. 3D visualization of liquefaction-induced dune collapse in the Navajo Sandstone, Utah, USA

    Science.gov (United States)

    Ford, Colby; Nick, Kevin; Bryant, Gerald

    2015-04-01

    The eolian Navajo Sandstone outcrop on the Canyon Overlook Trail in Zion National Park in Southern Utah is dissected by modern erosion in a way which reveals a great deal of the three-dimensional architecture of a major soft-sediment deformation event. The feature is bounded below by a well-developed interdune complex made up of two superimposed carbonate lenses, above by an irregular truncational surface, and incorporates 3 - 10 m of sandstone over an approximately 2 km area. The material above the deformed interval is undeformed cross-bedded sandstone, with crossbeds downlapping onto the surface of truncation. The stratigraphic confinement of deformation and the irregularity of the upper bounding surface suggests a deformation process which created topography, which was in turn covered by the next upwind dune before it could be eroded flat. The deformed material itself is laterally segmented by a stacked succession of shear surfaces, which all strike approximately perpendicular to the paleo-wind direction and dip at decreasing angles in the down paleo-wind direction. These factors point to the collapse of a major dune into the downwind interdune area, likely initiated by liquefaction in the interdune complex. The foundering of the dune's toe into the liquefied area created a powerful lateral stress field which did not extend significantly into the subsurface. The dune collapse process has been used in the past to describe other soft-sediment deformation features in the Navajo Sandstone, but this site provides a wealth of physical details which were not previously associated with dune collapse. Shear surfaces originate in the interdune deposit as slip between laminae, then the cohesive muds provided support as they were thrust upward to angles of up to 50 degrees. The margins of the site also contain important paleoenvironmental indicators. Dinosaur tracks are exposed both at the extreme upwind and downwind margins of the interdune deposit in and slightly above

  11. STRUCTURAL HETEROGENEITIES AND PALEO FLUID FLOW IN AN ANALOG SANDSTONE RESERVOIR 2001-2004

    International Nuclear Information System (INIS)

    Pollard, David; Aydin, Atilla

    2005-01-01

    Fractures and faults are brittle structural heterogeneities that can act both as conduits and barriers with respect to fluid flow in rock. This range in the hydraulic effects of fractures and faults greatly complicates the challenges faced by geoscientists working on important problems: from groundwater aquifer and hydrocarbon reservoir management, to subsurface contaminant fate and transport, to underground nuclear waste isolation, to the subsurface sequestration of CO2 produced during fossil-fuel combustion. The research performed under DOE grant DE-FG03-94ER14462 aimed to address these challenges by laying a solid foundation, based on detailed geological mapping, laboratory experiments, and physical process modeling, on which to build our interpretive and predictive capabilities regarding the structure, patterns, and fluid flow properties of fractures and faults in sandstone reservoirs. The material in this final technical report focuses on the period of the investigation from July 1, 2001 to October 31, 2004. The Aztec Sandstone at the Valley of Fire, Nevada, provides an unusually rich natural laboratory in which exposures of joints, shear deformation bands, compaction bands and faults at scales ranging from centimeters to kilometers can be studied in an analog for sandstone aquifers and reservoirs. The suite of structures there has been documented and studied in detail using a combination of low-altitude aerial photography, outcrop-scale mapping and advanced computational analysis. In addition, chemical alteration patterns indicative of multiple paleo fluid flow events have been mapped at outcrop, local and regional scales. The Valley of Fire region has experienced multiple episodes of fluid flow and this is readily evident in the vibrant patterns of chemical alteration from which the Valley of Fire derives its name. We have successfully integrated detailed field and petrographic observation and analysis, process-based mechanical modeling, and numerical

  12. Recent Exploration Progresses on Sandstone-Hosted Uranium Deposits in Northwestern China

    International Nuclear Information System (INIS)

    Li Ziying

    2014-01-01

    Conclusions: 1. China nuclear power development is stimulating exploration for uranium resources. 2. Big progress on exploration for sandstonehosted uranium deposits have been made for recent years. 3. The combined exploration techniques are effectively used for locating ore beds and targeting uranium mineralization. 4. Metallogenic models have played important roles in expansion and new discoveries of u-deposits. 5. Uranium is very mobile and can be enriched in the different types of rocks. 6. Greenish sandstone is due to chlorite alteration by secondary reduction process related to oil and gas and can be used to indicate uranium mineralization.

  13. Uranium mineralization in the Lower Mahadek Sandstones of Laitduh Area, East Khasi Hills District, Meghalaya

    International Nuclear Information System (INIS)

    Mahendra Kumar, K.; Bhattacharjee, P.; Ranganath, N.

    2008-01-01

    Significant uranium mineralization hosted in feldspathic sandstone of Upper Cretaceous Lower Mahadek Formation has been located at Laitduh, East Khasi Hills district, Meghalaya. Two mineralized horizons have been identified within Lower Mahadek Formation with vertical separation of 30 m. Samples from upper horizon have assayed upto 0.17% U 3 O 8 , whereas samples from lower mineralized horizon have assayed upto 0.50% U 3 O 8 . The radioactive minerals identified are coffinite and pitchblende occurring in association with carbonaceous matter. (author)

  14. Study of the Effect of Clay Particles on Low Salinity Water Injection in Sandstone Reservoirs

    Directory of Open Access Journals (Sweden)

    Sina Rezaei Gomari

    2017-03-01

    Full Text Available The need for optimal recovery of crude oil from sandstone and carbonate reservoirs around the world has never been greater for the petroleum industry. Water-flooding has been applied to the supplement primary depletion process or as a separate secondary recovery method. Low salinity water injection is a relatively new method that involves injecting low salinity brines at high pressure similar to conventional water-flooding techniques, in order to recover crude oil. The effectiveness of low salinity water injection in sandstone reservoirs depends on a number of parameters such as reservoir temperature, pressure, type of clay particle and salinity of injected brine. Clay particles present on reservoir rock surfaces adsorb polar components of oil and modify wettability of sandstone rocks to the oil-wet state, which is accountable for the reduced recovery rates by conventional water-flooding. The extent of wettability alteration caused by three low salinity brines on oil-wet sandstone samples containing varying clay content (15% or 30% and type of clay (kaolinite/montmorillonite were analyzed in the laboratory experiment. Contact angles of mica powder and clay mixture (kaolinite/montmorillonite modified with crude oil were measured before and after injection with three low salinity sodium chloride brines. The effect of temperature was also analyzed for each sample. The results of the experiment indicate that samples with kaolinite clay tend to produce higher contact angles than samples with montmorillonite clay when modified with crude oil. The highest degree or extent of wettability alteration from oil-wet to intermediate-wet state upon injection with low salinity brines was observed for samples injected with brine having salinity concentration of 2000 ppm. The increase in temperature tends to produce contact angles values lying in the higher end of the intermediate-wet range (75°–115° for samples treated at 50 °C, while their corresponding

  15. Influence of the properties of granite and sandstone in the desalination process by electrokinetic technique

    DEFF Research Database (Denmark)

    Feijoo, J.; Ottosen, Lisbeth M.; Pozo-Antonio, J.S.

    2015-01-01

    ) achieved in both stones.From the results obtained, it was possible to find those inherent factors to each stone which could have an influence on the efficacy of the treatment. With this technique it was possible to reduce the salt concentration in the granite almost to 100%. However, in the sandstone...... samples the decreases were not equally high, mainly at the intermediate levels where slight enrichments were observed. The results indicate that although the used technique is efficient for salt removal regardless of the porosimetric distribution of the rock, the better interconnection between the pores...... in the granite samples (favored a faster desalination process)....

  16. The sedimentology of uranium-bearing sandstones on the Waterval portion of the farm Brandewyns Gat 214, Beaufort West area

    International Nuclear Information System (INIS)

    Cole, D.I.

    1980-08-01

    The sedimentology of two uranium-bearing sandstones on the Waterval portion of the farm Brandewyns Gat 214 was studied by means of 36 vertical profiles measured across, through and adjacent to 4 mineralised deposits. The vertical profiles basically consist of a succession of sedimentary facies. A total of 19 facies was recognised within the fluvial sandstone sequence according to the criteria of grain-size and sedimentary structure. Transitions between the facies were subjected to a Markov chain analysis in order to delineate Markov-dependent transitions. Uranium mineralisation occurs mostly within the lower half of the fluvial sandstone sequence and is confined to the coarser-grained sedimentary facies. These facies probably acted as suitable aquifers for the transport of uraniferous solutions and permeability differences between the sandstone and the underlying mudstone and siltstone must have restricted these solutions to the lower half of the channel sandstone. The massive mudstone facies contains 13 per cent of the total cumulative thickness of mineralisation. This mineralisation probably originated from synchronously deposited tuffaceous material. Subsequent migration of uraniferous solutions may have concentrated the uranium

  17. Regional diagenesis of sandstone in the Upper Jurassic Morrison Formation, San Juan Basin, New Mexico and Colorado

    International Nuclear Information System (INIS)

    Hansley, P.L.

    1990-01-01

    The author reports that early authigenic mineral assemblages and vitroclastic textures are very well preserved in upper sandstones of the Upper Jurassic Morrison Formation. The distributions of the authigenic minerals were controlled, in part, by chemical gradients in a large saline, alkaline lake (Lake T'oo'dichi) that existed in late Morrison time. Sandstones on lake margins were cemented by smectite and silica, whereas sandstones nearer the lake center, in which waters were most saline and alkaline, were cemented by zeolites. Diagenetic alterations in sandstones were promoted by alkaline interstitial waters that emanated from adjacent fine-grained, tuffaceous lake beds. Metastable phases that precipitated first were replaced relatively quickly by more stable, ordered phases in the geochemically favorable environment of the closed basin setting. Elevation of temperatures above the geothermal gradient was proved by the influx of warm, deep-basin waters that locally modified early diagenetic assemblages during burial diagenesis. In organic- (and commonly also uranium ore-) bearing sandstones located primarily in the southern part of the basin, complex diagenetic assemblages resulted from water/rock reactions involving soluble organic complexes

  18. Open access

    CERN Document Server

    Suber, Peter

    2012-01-01

    The Internet lets us share perfect copies of our work with a worldwide audience at virtually no cost. We take advantage of this revolutionary opportunity when we make our work "open access": digital, online, free of charge, and free of most copyright and licensing restrictions. Open access is made possible by the Internet and copyright-holder consent, and many authors, musicians, filmmakers, and other creators who depend on royalties are understandably unwilling to give their consent. But for 350 years, scholars have written peer-reviewed journal articles for impact, not for money, and are free to consent to open access without losing revenue. In this concise introduction, Peter Suber tells us what open access is and isn't, how it benefits authors and readers of research, how we pay for it, how it avoids copyright problems, how it has moved from the periphery to the mainstream, and what its future may hold. Distilling a decade of Suber's influential writing and thinking about open access, this is the indispe...

  19. Open innovation

    DEFF Research Database (Denmark)

    West, Joel; Bogers, Marcel

    2017-01-01

    Interest in open innovation (OI) as a field of research has grown exponentially since the phrase was coined by Chesbrough in his 2003 book, with numerous articles, special issues, books, and conference sessions. Various reviews of the literature have summarized prior work, offered new frameworks......, and identified opportunities for future research. Here we summarize these opportunities, which include more research on outbound OI, the role of open innovation in services, and network forms of collaboration such as consortia, communities, ecosystems, and platforms. Research should also examine the use of OI...... by small, new, and not-for-profit organizations, as well as the linkage of individual actions and motivations to open innovation. Other opportunities include better measuring the costs, benefits, antecedents, mediators and moderators of the effects of OI on performance, and understanding why and how OI...

  20. Mudstone depressurization behaviour in an open pit coal mine, Indonesia

    Energy Technology Data Exchange (ETDEWEB)

    Marchand, G.; Waterhouse, J. [Golder Associates, West Perth, WA (Australia); Crisostomo, J. [PT Adaro Indonesia, Jakarta (Indonesia)

    2010-07-01

    Mining activities in the Tutupan mine in Indonesia began in the mid-1990s. The open pit mine's coal seams are interbedded with fine-grained sandstones, mudstones, and carbonaceous mudstones. Slope stability analyses at the pit have integrated hydrogeology with geotechnical engineering analyses to optimize slope designs and reduce the risk of slope failure. This paper discussed the impact of mining and dewatering on mudstone depressurization. Sensors were placed at key points in the mine to obtain data related to the mudstone units. Reductions in pore pressure occurred as a result of groundwater flow away from the observed zones, increases in porosity, and increases in total porosity caused by an expansion of the rock mass as a result of drainage and hydrostatic unloading. Mudstone pore pressure trends with time were interpreted by determining the thickness of the mudstone unit, the presence or absence of known thin sandstone beds, unloading from overhead mining activities, and the position of the mudstone within the sedimentary sequence. The study showed that unloading activities have a significant impact on pore pressure in thick mudstone units, regardless of the depth, thickness, or properties of the unit. Pore pressure within high wall mudstone units typically decreased to values equivalent to the elevation of the unit where it was exposed to dips in a high wall. The dewatering of sandstone units in low walls caused a decline in pore pressure within the thick mudstone units located beneath the sandstones. Differences in primary permeabilities were attributed to greater fracturing in deeper and stronger rock units. 3 refs., 4 figs.

  1. Development and comparison of different intensity duration ...

    African Journals Online (AJOL)

    Nigerian Journal of Technology ... Microsoft Excel software was used to develop exponential, logarithmic and power intensity-duration-frequency models for return period (T) of duration-frequency models for return period (T) of between 2 years and 100 years using rainfall intensity data for durations of 2, 5, 10, 15, 30, 60, ...

  2. Speaker-specific variability of phoneme durations

    CSIR Research Space (South Africa)

    Van Heerden, CJ

    2007-11-01

    Full Text Available The durations of phonemes varies for different speakers. To this end, the correlations between phonemes across different speakers are studied and a novel approach to predict unknown phoneme durations from the values of known phoneme durations for a...

  3. Open Education and the Open Science Economy

    Science.gov (United States)

    Peters, Michael A.

    2009-01-01

    Openness as a complex code word for a variety of digital trends and movements has emerged as an alternative mode of "social production" based on the growing and overlapping complexities of open source, open access, open archiving, open publishing, and open science. This paper argues that the openness movement with its reinforcing structure of…

  4. Analysis of metallogenic conditions of sandstone type uranium deposits in interlayer oxidation zone in the northwest of Junggar basin, Xinjiang

    International Nuclear Information System (INIS)

    Lin Shuangxing

    1997-01-01

    From various aspects such as the basin structures, structure features of the sedimentary cover, lithofacies features of basin sediments, geochemical characteristics of sedimentary rocks, regional hydrogeologic conditions and epigenetic reworking of the sedimentary cover and so on, the author analyzes the metallogenic conditions of sandstone type uranium deposits in interlayer oxidation zone in the northwest of Junggar basin. The author proposes that the area has abundant uranium sources, and possesses favourable stratigraphic combinations for the development of interlayer oxidation zone. Secondarily oxidized sandstone bodies present universally at places from the source area to stream channel facies. Reducing beds and secondarily reducing barrier are developed at the front of the secondarily oxidized sandstone body. The tectonic features of the sedimentary cover indicate that the area belongs to a relatively-stable suborogenic region and possesses secondary mobilization and reworking conditions during the uplifting and contraction stage of the basin. Epigenetic metallization is evident in the sedimentary cover of the basin

  5. Geological characteristics and prospecting potential of sandstone-type uranium deposits in the north margin of Qaidam basin

    International Nuclear Information System (INIS)

    Liu Lin; Song Xiansheng; Feng Wei

    2012-01-01

    The north margin of Qaidam Basin is composed with rift trough and Oulongbuluke landmass which is clamped by Qilian Mountain and Qaidam block Suture zone. The two activities provide a rich source of uranium for the basin area. The coal-bearing rocks as stratums of medium and lower Jurassic, is the main exploration target zones of sandstone-type uranium ore. Through geological survey and drilling, we think that the interlayer oxidation zone. being primary factors of sandstone-type uranium, can be divided into ancient type and modern type. The ancient interlayer oxidation zone type uranium deposit is the main prospecting types in the north margin of Qaidam Basin. Combined with analysis on geological conditions of sandstone-type uranium mineralization, we propose that eastern edge of Yuqia, southern edge of Lucao Mountain, Beidatan and northwest edge of Ulan depression are good prospects. (authors)

  6. Geochemical interpretation of the Precambrian basement and overlying Cambrian sandstone on Bornholm, Denmark: Implications for the weathering history

    DEFF Research Database (Denmark)

    Zhou, Lingli; Friis, Henrik; Yang, Tian

    2017-01-01

    show a depletion of major elements in the following order: Na N Ca N Mg N Si; Al and Ti are immobile and stay constant; K shows sample dependent enrichment or depletion; Fe is slightly enriched. The Cambrian sandstone overlying the basement in the Borggård borehole, assigned to the Gadeby Member...... but lost most of the plagioclase. The LSF has a comparable weathering history (CIA = 63–73), but the plagioclase is better preserved (PIA = 65–78). The significant variation of weathering rates of plagioclase and K-feldspar in the basement granite and the provenance of sandstone from the Borggård borehole...... are likely due to the different permeability developed within the internal crystal structures, a Ca- rich plagioclase original composition of the plagioclase, and the occurrence of weathering in a very humid climate. K metasomatism occurred in the basement granite and sandstone in both the Borggård and the G...

  7. Impact of sauropod dinosaurs on lagoonal substrates in the Broome Sandstone (Lower Cretaceous, Western Australia.

    Directory of Open Access Journals (Sweden)

    Tony Thulborn

    Full Text Available Existing knowledge of the tracks left by sauropod dinosaurs (loosely 'brontosaurs' is essentially two-dimensional, derived mainly from footprints exposed on bedding planes, but examples in the Broome Sandstone (Early Cretaceous of Western Australia provide a complementary three-dimensional picture showing the extent to which walking sauropods could deform the ground beneath their feet. The patterns of deformation created by sauropods traversing thinly-stratified lagoonal deposits of the Broome Sandstone are unprecedented in their extent and structural complexity. The stacks of transmitted reliefs (underprints or ghost prints beneath individual footfalls are nested into a hierarchy of deeper and more inclusive basins and troughs which eventually attain the size of minor tectonic features. Ultimately the sauropod track-makers deformed the substrate to such an extent that they remodelled the topography of the landscape they inhabited. Such patterns of substrate deformation are revealed by investigating fragmentary and eroded footprints, not by the conventional search for pristine footprints on intact bedding planes. For that reason it is not known whether similar patterns of substrate deformation might occur at sauropod track-sites elsewhere in the world.

  8. Origin of sandstone-hosted uranium deposits, Frome Embayment, South Australia

    International Nuclear Information System (INIS)

    Sanford, R.F.

    1985-01-01

    The formation of sandstone-hosted uranium deposits in the Frome Embayment of South Australia is largely a result of tectonic events possibly as old as the Archean. Uranium deposits of several types and ages in the region demonstrate the importance of uranium enrichment in the source area. Mobile zones around the Archean terrane of the Gawler block have been the locus of intermittent tectonic activity from Early Proterozoic to recent time. Vein-type uranium deposits in basement source rocks are concentrated in these zones, because they favor deep crustal partial melting and ascent of Na-rich granitic magmas and hydrothermal solutions. Relatively stable areas bordered by mobile zones, are important for the formation of sandstone-hosted uranium deposits because they act as platforms for terrigenous sedimentation from the surrounding, uplifted, uranium-rich basement rocks. Wet, subtropical conditions prevailing at the time of uplift aided rapid erosion and subaerial deposition of channel sands with intermixed organic detritus. Later uplift accompanied by erosion of the recently deposited sands in the headwater area caused increased recharge of oxygenated uraniferous ground water, which led to the formation of geochemical-cell roll-front type deposits like those in the Wyoming basins. Subsequent arid conditions helped preserve the deposits. (author)

  9. Reservoir heterogeneity in carboniferous sandstone of the Black Warrior basin. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kugler, R.L.; Pashin, J.C.; Carroll, R.E.; Irvin, G.D.; Moore, H.E.

    1994-06-01

    Although oil production in the Black Warrior basin of Alabama is declining, additional oil may be produced through improved recovery strategies, such as waterflooding, chemical injection, strategic well placement, and infill drilling. High-quality characterization of reservoirs in the Black Warrior basin is necessary to utilize advanced technology to recover additional oil and to avoid premature abandonment of fields. This report documents controls on the distribution and producibility of oil from heterogeneous Carboniferous reservoirs in the Black Warrior basin of Alabama. The first part of the report summarizes the structural and depositional evolution of the Black Warrior basin and establishes the geochemical characteristics of hydrocarbon source rocks and oil in the basin. This second part characterizes facies heterogeneity and petrologic and petrophysical properties of Carter and Millerella sandstone reservoirs. This is followed by a summary of oil production in the Black Warrior basin and an evaluation of seven improved-recovery projects in Alabama. In the final part, controls on the producibility of oil from sandstone reservoirs are discussed in terms of a scale-dependent heterogeneity classification.

  10. Role of Some Isolated Fungi in The Biological Leaching of Uranium From Low Grade Cretaceous Sandstone

    International Nuclear Information System (INIS)

    Ibrahim, H.A.; Morsy, A.; El-Sheikh, E.M.

    2012-01-01

    Microbiological leaching has been used as an alternative approach to conventional hydrometallurgical methods of uranium extraction. In this investigation, the biological leaching of uranium by isolated fungi from low grade sandstone was studied. Five isolates of fungi were obtained from sandstone sample. Cladosporium oxysporum and Penicilluim stoloniferum exhibited high potential in generating a variety of organic acids effective for uranium extraction. The percentages of organic acid produced by fungi were determined. By-product such as molasses was tested. The maximum dissolution of uranium was achieved at the following conditions; incubation period 6 days, pulp density 1:3 g/L, ph 3.5 and at 30 degree C. Maximum solubilization of uranium with values of 54% and 67% were achieved by Cladosporium oxysporum and Penicilluim stoloniferum, respectively. From properly prepared pregnant bio-leach liquor, the leached uranium was recovered in the form of marketable products (3UO 3 NH 3 .5H 2 O) using classical chemical technique and the product was confirmed using XRD techniques

  11. Pore Structure and Limit Pressure of Gas Slippage Effect in Tight Sandstone

    Science.gov (United States)

    You, Lijun; Xue, Kunlin; Kang, Yili; Liao, Yi

    2013-01-01

    Gas slip effect is an important mechanism that the gas flow is different from liquid flow in porous media. It is generally considered that the lower the permeability in porous media is, the more severe slip effect of gas flow will be. We design and then carry out experiments with the increase of backpressure at the outlet of the core samples based on the definition of gas slip effect and in view of different levels of permeability of tight sandstone reservoir. This study inspects a limit pressure of the gas slip effect in tight sandstones and analyzes the characteristic parameter of capillary pressure curves. The experimental results indicate that gas slip effect can be eliminated when the backpressure reaches a limit pressure. When the backpressure exceeds the limit pressure, the measured gas permeability is a relatively stable value whose range is less than 3% for a given core sample. It is also found that the limit pressure increases with the decreasing in permeability and has close relation with pore structure of the core samples. The results have an important influence on correlation study on gas flow in porous medium, and are beneficial to reduce the workload of laboratory experiment. PMID:24379747

  12. Full-scale laboratory drilling tests on sandstone and dolomite. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Black, A. D.; Green, S. J.; Rogers, L. A.

    1977-08-01

    Full-scale laboratory drilling experiments were performed under simulated downhole conditions to determine what effect changing various drilling parameters has on penetration rate. The two rock types, typical of deep oil and gas reservoirs, used for the tests were Colton Sandstone and Bonne Terre Dolomite. Drilling was performed with standard 7/sup 7///sub 8/ inch rotary insert bits and water base mud. The results showed the penetration rate to be strongly dependent on bit weight, rotary speed and borehole mud pressure. There was only a small dependence on mud flow rate. The drilling rate decreased rapidly with increasing borehole mud pressure for borehole pressures up to about 2,000 psi. Above this pressure, the borehole pressure and rotary speeds had a smaller effect on penetration rate. The penetration rate was then dependent mostly on the bit weight. Penetration rate per horsepower input was also shown to decrease at higher mud pressures and bit weights. The ratio of horizontal confining stress to axial overburden stress was maintained at 0.7 for simulated overburden stresses between 0 and 12,800 psi. For this simulated downhole stress state, the undrilled rock sample was within the elastic response range and the confining pressures were found to have only a small or negligible effect on the penetration rate. Visual examination of the bottomhole pattern of the rocks after simulated downhole drilling, however, revealed ductile chipping of the Sandstone, but more brittle behavior in the Dolomite.

  13. Estimates of vertical hydraulic conductivity in the middle Dakota Sandstone, Monticello, Utah

    International Nuclear Information System (INIS)

    Kautsky, M.; Kearl, P.M.; Dexter, J.J.; Zinkl, R.J.

    1986-01-01

    There are about 2 million tons of uranium mill tailings which lie directly on top of an alluvial aquifer at the Monticello millsite, Utah. The aquifer is contaminated as a consequence of leachate percolating through the tailings. The Burro Canyon Formation which is the local culinary aquifer, underlies the site at depth, but is isolated from the alluvial aquifer by an aquitard composed primarily of middle Dakota Sandstone, and some Mancos Shale. Water quality monitoring of the Burro Canyon aquifer has indicated that it contains very low to no contamination by radionuclides. Tritium data have shown that the recharge to the aquifer predates 1953. Pump tests conducted on the system using the ratio method, have shown the vertical hydraulic conductivity of the aquitard is some 5.2 x 10/sup -7/ to 8.0 x 10/sup -9/ m/d (1.7 x 10/sup -6/ to 2.6 x 10/sup -8/ ft/d). Based upon the aquifer monitoring and test data, the middle Dakota Sandstone appears to be an effective aquitard impeding the downward migration of contaminants from the alluvial aquifer to the Burro Canyon aquifer

  14. Constitutive Modelling and Deformation Band Angle Predictions for High Porosity Sandstones

    Science.gov (United States)

    Richards, M. C.; Issen, K. A.; Ingraham, M. D.

    2017-12-01

    The development of a field-scale deformation model requires a constitutive framework that is capable of representing known material behavior and able to be calibrated using available mechanical response data. This work employs the principle of hyperplasticity (e.g., Houlsby and Puzrin, 2006) to develop such a constitutive framework for high porosity sandstone. Adapting the works of Zimmerman et al. (1986) and Collins and Houlsby (1997), the mechanical data set of Ingraham et al. (2013 a, b) was used to develop a specific constitutive framework for Castlegate sandstone, a high porosity fluvial-deposited reservoir analog rock. Using the mechanical data set of Ingraham et al. (2013 a, b), explicit expressions and material parameters of the elastic moduli and strain tensors were obtained. With these expressions, analytical and numerical techniques were then employed to partition the total mechanical strain into elastic, coupled, and plastic strain components. With the partitioned strain data, yield surfaces in true-stress space, coefficients of internal friction, dilatancy factors, along with the theorectical predictions of the deformation band angles were obtained. These results were also evaluated against band angle values obtained from a) measurements on specimen jackets (Ingraham et al., 2013a), b) plane fits through located acoustic emissions (AE) events (Ingraham et al. 2013b), and c) X-ray micro-computed tomography (micro-CT) calculations.

  15. Correlation development between indentation parameters and uniaxial compressive strength for Colombian sandstones

    International Nuclear Information System (INIS)

    Mateus, Jefferson; Saavedra, Nestor Fernando; Calderon Carrillo, Zuly; Mateus, Darwin

    2007-01-01

    A new way to characterize the perforated formation strength has been implemented using the indentation test. This test can be performed on irregular cuttings mounted in acrylic resins forming a disc. The test consists of applying load on each sample by means of a flat and indenter. A graph of the load applied VS penetration of the indenter is developed, and the modules of the test, denominated indentation modulus (IM) and Critical Transition Force (CTF) are obtained (Ringstad et al., 1998). Based on the success of previous studies we developed correlations between indentation and mechanical properties for some Colombian sandstone. These correlations were obtained using o set of 248 indentation tests and separate compression fasts on parallel sandstone samples from the same depth. This analysis includes Barco Formation, Mirador Formation, and Tambor Formation. For the correlations, IM-UCS and CTF-UCS, the correlation coefficient is 0.81 and 0.70 respectively. The use of the correlations and the indentation test is helpful for in-situ calibration of the geomechanical models since the indentation test can be performed in real time thus reducing costs and time associated with delayed conventional characterization

  16. Metallogenic geologic conditions and prospecting direction of sandstone type uranium mineralizations in Yili basin of Xinjiang

    International Nuclear Information System (INIS)

    Chen Daisheng; Wang Ruiying; Li Shengxiang; Zhang Kefang

    1994-09-01

    Yili basin is a Mesozoic down-warped basin superimposed on the late Paleozoic volcanic taphrogenic basin. Uranium mineralizations are hosted in the Middle-Lower Jurassic coal-bearing series. The depositions environment in the basin is turbulent in the east and relatively stable in the west. It is characterized by coarse-grained sequence with thin thickness in the eastern part and fine-grained with thick thickness in the western part. On the analytical basis of sedimentary facies indices, it is the first time to present a sedimentary model of 'alluvial fan-braided stream-(narrow) lakeshore delta-lacustrine facies and marsh facies' for the coal-bearing series. The authors have summarized the basic geologic features of U-mineralizations in the interlayer oxidation zone, analyzed the difference and cause of U-mineralizations between the south and north, as well as the east and west. The genetic mechanism of U-mineralizations in the basin is discussed. Finally, seven items of geologic prerequisites for the formation of in-situ leachable sandstone type uranium deposits have been suggested and the potential of sandstone type U-mineralizations in the basin has been evaluated. Four promising target areas are selected

  17. Impact of Sauropod Dinosaurs on Lagoonal Substrates in the Broome Sandstone (Lower Cretaceous), Western Australia

    Science.gov (United States)

    Thulborn, Tony

    2012-01-01

    Existing knowledge of the tracks left by sauropod dinosaurs (loosely ‘brontosaurs’) is essentially two-dimensional, derived mainly from footprints exposed on bedding planes, but examples in the Broome Sandstone (Early Cretaceous) of Western Australia provide a complementary three-dimensional picture showing the extent to which walking sauropods could deform the ground beneath their feet. The patterns of deformation created by sauropods traversing thinly-stratified lagoonal deposits of the Broome Sandstone are unprecedented in their extent and structural complexity. The stacks of transmitted reliefs (underprints or ghost prints) beneath individual footfalls are nested into a hierarchy of deeper and more inclusive basins and troughs which eventually attain the size of minor tectonic features. Ultimately the sauropod track-makers deformed the substrate to such an extent that they remodelled the topography of the landscape they inhabited. Such patterns of substrate deformation are revealed by investigating fragmentary and eroded footprints, not by the conventional search for pristine footprints on intact bedding planes. For that reason it is not known whether similar patterns of substrate deformation might occur at sauropod track-sites elsewhere in the world. PMID:22662116

  18. Performance of Surfactant Methyl Ester Sulphonate solution for Oil Well Stimulation in reservoir sandstone TJ Field

    Science.gov (United States)

    Eris, F. R.; Hambali, E.; Suryani, A.; Permadi, P.

    2017-05-01

    Asphaltene, paraffin, wax and sludge deposition, emulsion and water blocking are kinds ofprocess that results in a reduction of the fluid flow from the reservoir into formation which causes a decrease of oil wells productivity. Oil well Stimulation can be used as an alternative to solve oil well problems. Oil well stimulation technique requires applying of surfactant. Sodium Methyl Ester Sulphonate (SMES) of palm oil is an anionic surfactant derived from renewable natural resource that environmental friendly is one of potential surfactant types that can be used in oil well stimulation. This study was aimed at formulation SMES as well stimulation agent that can identify phase transitions to phase behavior in a brine-surfactant-oil system and altered the wettability of rock sandstone and limestone. Performance of SMES solution tested by thermal stability test, phase behavioral examination and rocks wettability test. The results showed that SMES solution (SMES 5% + xylene 5% in the diesel with addition of 1% NaCl at TJformation water and SMES 5% + xylene 5% in methyl ester with the addition of NaCl 1% in the TJ formation water) are surfactant that can maintain thermal stability, can mostly altered the wettability toward water-wet in sandstone reservoir, TJ Field.

  19. NMR Pore Structure and Dynamic Characteristics of Sandstone Caused by Ambient Freeze-Thaw Action

    Directory of Open Access Journals (Sweden)

    Bo Ke

    2017-01-01

    Full Text Available For a deeper understanding of the freeze-thaw weathering effects on the microstructure evolution and deterioration of dynamic mechanical properties of rock, the present paper conducted the nuclear magnetic resonance (NMR tests and impact loading experiments on sandstone under different freeze-thaw cycles. The results of NMR test show that, with the increase of freeze-thaw cycles, the pores expand and pores size tends to be uniform. The experimental results show that the stress-strain curves all go through four stages, namely, densification, elasticity, yielding, and failure. The densification curve is shorter, and the slope of elasticity curve decreases as the freeze-thaw cycles increase. With increasing freeze-thaw cycles, the dynamic peak stress decreases and energy absorption of sandstone increases. The dynamic failure form is an axial splitting failure, and the fragments increase and the size diminishes with increasing freeze-thaw cycles. The higher the porosity is, the more severe the degradation of dynamic characteristics is. An increase model for the relationships between the porosity or energy absorption and freeze-thaw cycles number was built to reveal the increasing trend with the freeze-thaw cycles increase; meanwhile, a decay model was built to predict the dynamic compressive strength degradation of rock after repeated freeze-thaw cycles.

  20. Microbial leaching of low grade sandstone uranium ores: column leaching studies

    International Nuclear Information System (INIS)

    Bhatti, T.M.; Malik, K.A.; Khalid, A.M.

    1991-01-01

    Microbial leaching studies on a low-grade sandstone uranium ore from Baghalchur Ore Deposits, D. G. Khan, Pakistan, containing 0.027 % U/sub 3/O/sub 8/ for extraction of uranium, were conducted in columns. Baghalchur sandstone uranium ore which is alkaline in nature, contained 5.0% calcite [CaCo/sub 3/], 2-3 % Fe/sub 2/O/sub 3/ and pyrite [FeS/sub 2/] less than 0.1 %. The ore amended with sulfur and/or sulfur slag as external energy source was found to leach with indigenous microflora mostly belonging to the genus Thiobacillus which are present in the uranium mine water. Column leaching studies revealed that when the ore was amended with elemental sulfur and irrigated with mine water (pH 3.5) 53 % U/sub 3/O/sub 8/ could be solubilized from it. However, when the natural mine water was used as such (pH 7.4) the solubilization of uranium was decreased to 41 % U/sub 3/O/sub 8/ in 90 days under similar conditions of percolation rate and temperature. The addition of (NH/sub 4/)/sub 2/SO/sub 4/ (3.0 g/L) in mine water was found to enhance the uranium leaching to 70 % U/sub 3/O/sub 8/ from the columns containing ore amended with sulfur slag. (author)

  1. Reservoir heterogeneity in Carboniferous sandstone of the Black Warrior basin. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kugler, R.L.; Pashin, J.C.; Carroll, R.E.; Irvin, G.D.; Moore, H.E.

    1994-04-01

    Although oil production in the Black Warrior basin of Alabama is declining, additional oil may be produced through improved recovery strategies, such as waterflooding, chemical injection, strategic well placement, and infill drilling. High-quality characterization of reservoirs in the Black Warrior basin is necessary to utilize advanced technology to recover additional oil and to avoid premature abandonment of fields. This report documents controls on the distribution and producibility of oil from heterogeneous Carboniferous reservoirs in the Black Warrior basin of Alabama. The first part of the report summarizes the structural and depositional evolution of the Black Warrior basin and establishes the geochemical characteristics of hydrocarbon source rocks and oil in the basin. This second part characterizes facies heterogeneity and petrologic and petrophysical properties of Carter and Millerella sandstone reservoirs. This is followed by a summary of oil production in the Black Warrior basin and an evaluation of seven improved-recovery projects in Alabama. In the final part, controls on the producibility of oil from sandstone reservoirs are discussed in terms of a scale-dependent heterogeneity classification.

  2. Uranium leaching from phosphatic sandstone and shale of Qatrani using citrate as a new leaching reagent

    International Nuclear Information System (INIS)

    Hussein, E.M.

    1997-01-01

    Uranium is found in Qatrani area (Southwest of Cairo and North of lake Qarun) in various forms in sedimentary rocks. Two important ore materials have been chosen for studying the recovery of their uranium contents namely; the phosphatic sandstone and the carbonaceous shale. The main emphasis in this thesis is the choice of an acid that would selectively leach uranium from thesis ores while leaving calcium phosphate and carbonate minerals minerals almost completely intact. Citric acid was indeed found advantageous due primarily to its strong ability to form stable complexes with uranium over a wide range of PH values beside the possibility of controlling thr solubility of calcium-bearing compounds by adding calcium citrate. The latter is actually characterized by its ability to exist in an unionized or associated from in citric acid solutions. From the general leaching characteristics of both uranium and P 2 O 5 from Qatrani phosphatic sandstone by citric acid, it was found that uranium could be completely leached beside the possibility of realizing a differential leaching percent values vs P 2 O 5 which is generally of limited solubility. Such a low solubility of P 2 O 5 has even been completely inhibited by providing calcium citrate to the citric acid solutions in amounts sufficient to exist in an optimum ionized non-associated state. Such a provision would render the solution unable to carry any further calcium ions thus the breakdown of the phosphate mineral was hindered while uranium has completely been selectively

  3. Metal release from sandstones under experimentally and numerically simulated CO2 leakage conditions.

    Science.gov (United States)

    Kirsch, Katie; Navarre-Sitchler, Alexis K; Wunsch, Assaf; McCray, John E

    2014-01-01

    Leakage of CO2 from a deep storage formation into an overlying potable aquifer may adversely impact water quality and human health. Understanding CO2-water-rock interactions is therefore an important step toward the safe implementation of geologic carbon sequestration. This study targeted the geochemical response of siliclastic rock, specifically three sandstones of the Mesaverde Group in northwestern Colorado. To test the hypothesis that carbonate minerals, even when present in very low levels, would be the primary source of metals released into a CO2-impacted aquifer, two batch experiments were conducted. Samples were reacted for 27 days with water and CO2 at partial pressures of 0.01 and 1 bar, representing natural background levels and levels expected in an aquifer impacted by a small leakage, respectively. Concentrations of major (e.g., Ca, Mg) and trace (e.g., As, Ba, Cd, Fe, Mn, Pb, Sr, U) elements increased rapidly after CO2 was introduced into the system, but did not exceed primary Maximum Contaminant Levels set by the U.S. Environmental Protection Agency. Results of sequential extraction suggest that carbonate minerals, although volumetrically insignificant in the sandstone samples, are the dominant source of mobile metals. This interpretation is supported by a simple geochemical model, which could simulate observed changes in fluid composition through CO2-induced calcite and dolomite dissolution.

  4. The Open

    Directory of Open Access Journals (Sweden)

    Saitya Brata Das

    2009-12-01

    Full Text Available In the Open darkness and light, remembrance and oblivion, coming into existence and disappearing in death play their originary co-belonging, or co-figuration. Existence belongs to this opening and is exposed to its coming to presence: it is on the basis of this originary opening, this originary historical which is revealed to this mortal being called ‘man,’ on the basis of this revelation, man founds something like politics and history. There thus comes into existence out of this freedom, out of this “play space”2, this field called ‘polis’3 where there takes place war and festival, where historical revolutions tear apart history, brings ruptures and discontinuities in the very mode of his existence, where man seeks the foundation of his own foundation (which is his metaphysical task , where occurs the dialectics of negativity between man and man, where man puts at stake his own death, his own dissolution, and by the power of his own dissolution stands in relation to the total world that he seeks to dominate. This means that man’s attempts to metaphysically found his own political and historical existence must presuppose a far more originary non-foundation, the differentiating revealing of the open, the ungrounded spacing play, or playing space of natality and mortality.

  5. Open data

    DEFF Research Database (Denmark)

    Bodum, Lars

    2017-01-01

    Everyone wants open data, but the road towards it can be both difficult and long. Implementation of data portals and ICT solutions for support of the data infrastructure can be initiated from the central government through legislation, regulation and public procurement. This is what you would call...

  6. Open Images

    DEFF Research Database (Denmark)

    Sanderhoff, Merete

    2013-01-01

    Museums around the world hold enormous troves of public domain artworks. In digitized form, they can be powerful tools for research and learning, as well as building blocks, in the hands of students, teachers, scholars, developers, and creative people. By opening up their digitized assets for reuse...

  7. Sandstone uranium deposits of Eurasia – from genetic concepts to forecasting and new discoveries

    International Nuclear Information System (INIS)

    Pechenkin, I.

    2014-01-01

    Along the Eurasian continent’s southern borders lie uranium ore provinces and regions controlling medium-sized and, on rare occasions, large sandstone deposits. Central French, Eastern Rhodope and other regions are known in the west. Large uranium ore provinces were discovered in the south of the Turan Plate and in the depressions of South Kazakhstan, viz. Central Kyzyl Kum, Syr Darya, Chu Sarysu. A common criterion has been established for all objects of the sandstone type, located in oil and gas, coal etc. sedimentary basins – the zone of interlayer or ground-interlayer oxidation, controlling uranium mineralization. In 2003 we were able to justify the concept that the formation of giant deposits in Chu Sarysu province was caused by the collision between the Indian Plate and the southern part of the Eurasian continent. Within the limits of Pacific ore belt there is a zonal distribution of ore deposits. Ordinary mineralization is drawn towards its eastern fringe: gold, tin, copper, tungsten etc. Volcanic and tectonic structures of central type of Mesozoic age are located further west, from the north to the south, that is large calderas – Streltsovskaya (Russia), Dornot (Mongolia), Sian Shan (China), which control large and unique endogene uranium deposits. In the far west, in the region of subsiding tectonic tensions, there are sandstone deposits of uranium in Transbaikalia, Mongolia and Yunnan, which are specially connected to young basalts. Infiltration deposits of Vitim region are adjacent to endogene deposits of Streltsovsky region in the southern-easterly direction, and to the east of the deposits of Yunnan at the same latitude lay the Sian Shan caldera with geothermal deposits of uranium and other metals. We combined them into the unified submeridional Baikal-Southern China uranium ore belt. After examining the southern extremities of the Eurasian continent, the region of the collision of the Indian Plate, a distinct similarity can be perceived between

  8. Predictive modeling of CO2 sequestration in deep saline sandstone reservoirs: Impacts of geochemical kinetics

    Energy Technology Data Exchange (ETDEWEB)

    Balashov, Victor N.; Guthrie, George D.; Hakala, J. Alexandra; Lopano, Christina L.; Rimstidt, J. Donald; Brantley, Susan L.

    2013-03-01

    One idea for mitigating the increase in fossil-fuel generated CO{sub 2} in the atmosphere is to inject CO{sub 2} into subsurface saline sandstone reservoirs. To decide whether to try such sequestration at a globally significant scale will require the ability to predict the fate of injected CO{sub 2}. Thus, models are needed to predict the rates and extents of subsurface rock-water-gas interactions. Several reactive transport models for CO{sub 2} sequestration created in the last decade predicted sequestration in sandstone reservoirs of ~17 to ~90 kg CO{sub 2} m{sup -3|. To build confidence in such models, a baseline problem including rock + water chemistry is proposed as the basis for future modeling so that both the models and the parameterizations can be compared systematically. In addition, a reactive diffusion model is used to investigate the fate of injected supercritical CO{sub 2} fluid in the proposed baseline reservoir + brine system. In the baseline problem, injected CO{sub 2} is redistributed from the supercritical (SC) free phase by dissolution into pore brine and by formation of carbonates in the sandstone. The numerical transport model incorporates a full kinetic description of mineral-water reactions under the assumption that transport is by diffusion only. Sensitivity tests were also run to understand which mineral kinetics reactions are important for CO{sub 2} trapping. The diffusion transport model shows that for the first ~20 years after CO{sub 2} diffusion initiates, CO{sub 2} is mostly consumed by dissolution into the brine to form CO{sub 2,aq} (solubility trapping). From 20-200 years, both solubility and mineral trapping are important as calcite precipitation is driven by dissolution of oligoclase. From 200 to 1000 years, mineral trapping is the most important sequestration mechanism, as smectite dissolves and calcite precipitates. Beyond 2000 years, most trapping is due to formation of aqueous HCO{sub 3}{sup -}. Ninety-seven percent of the

  9. Aspects of the sedimentology of some uranium-bearing sandstones in the Beaufort West area, Cape Province

    International Nuclear Information System (INIS)

    Cole, D.I.

    1980-01-01

    The sedimentology of some uranium-bearing sandstones from the Beaufort Group in the Beaufort West area was studied by use of some 116 vertical profiles measured across and adjacent to 14 mineralized deposits. The vertical profiles consist of 91 field sections and 25 borehole logs. The sandstones are usually multistorey and alternate with a mudstone and/or siltstone succession. The vertical profiles basically consist of a succession of facies. Some 19 facies were recognised within the sandstones on the basis of texture and sedimentary structure. The facies transitions within the sandstone sequence were subjected to a one-step Markov chain analysis. The cumulative thickness of uranium mineralization for each sedimentary facies within the sandstone sequence was measured. Some 99 per cent of the total cumulative thickness occurs within the coarser-grained facies (grain sizes in excess of very fine), which suggests that permeability was an important control on the mineralization. The coarser-grained facies, which mostly represent lower point bar or channel bar deposits near the base of each storey, probably acted as suitable aquifers for the transport of uraniferous solutions. Irregularities in the base of each storey may have interrupted the flow of these solutions and allowed sufficient time for precipitation of the uranium. Carbonaceous debris is frequently associated with the mineralized deposits and most likely acted as an indirect reductant for this precipitation. Mineralization decreases upwards in the sandstone sequence and some 40 per cent of the total cumulative thickness is restricted to the initial storey. The horizontally bedded facies contain a high proportion of the total cumulative thickness of mineralization (45 per cent) and this again may be related to a more abundant content of carbonaceous debris

  10. Experimental measurements of the SP response to concentration and temperature gradients in sandstones with application to subsurface geophysical monitoring

    Science.gov (United States)

    Leinov, E.; Jackson, M. D.

    2014-09-01

    Exclusion-diffusion potentials arising from temperature gradients are widely neglected in self-potential (SP) surveys, despite the ubiquitous presence of temperature gradients in subsurface settings such as volcanoes and hot springs, geothermal fields, and oil reservoirs during production via water or steam injection. Likewise, with the exception of borehole SP logging, exclusion-diffusion potentials arising from concentration gradients are also neglected or, at best, it is assumed that the diffusion potential dominates. To better interpret these SP sources requires well-constrained measurements of the various coupling terms. We report measurements of thermoelectric and electrochemical exclusion-diffusion potentials across sandstones saturated with NaCl brine and find that electrode effects can dominate the measured voltage. After correcting for these, we find that Hittorf transport numbers are the same within experimental error regardless of whether ion transport occurs in response to temperature or concentration gradients over the range of NaCl concentration investigated that is typical of natural systems. Diffusion potentials dominate only if the pore throat radius is more than approximately 4000 times larger than the diffuse layer thickness. In fine-grained sandstones with small pore throat diameter, this condition is likely to be met only if the saturating brine is of relatively high salinity; thus, in many cases of interest to earth scientists, exclusion-diffusion potentials will comprise significant contributions from both ionic diffusion through, and ionic exclusion from, the pore space of the rock. However, in coarse-grained sandstones, or sandstones saturated with high-salinity brine, exclusion-diffusion potentials can be described using end-member models in which ionic exclusion is neglected. Exclusion-diffusion potentials in sandstones depend upon pore size and salinity in a complex way: they may be positive, negative, or zero depending upon sandstone

  11. Electrofacies vs. lithofacies sandstone reservoir characterization Campanian sequence, Arshad gas/oil field, Central Sirt Basin, Libya

    Science.gov (United States)

    Burki, Milad; Darwish, Mohamed

    2017-06-01

    The present study focuses on the vertically stacked sandstones of the Arshad Sandstone in Arshad gas/oil field, Central Sirt Basin, Libya, and is based on the conventional cores analysis and wireline log interpretation. Six lithofacies types (F1 to F6) were identified based on the lithology, sedimentary structures and biogenic features, and are supported by wireline log calibration. From which four types (F1-F4) represent the main Campanian sandstone reservoirs in the Arshad gas/oil field. Lithofacies F5 is the basal conglomerates at the lower part of the Arshad sandstones. The Paleozoic Gargaf Formation is represented by lithofacies F6 which is the source provenance for the above lithofacies types. Arshad sediments are interpreted to be deposited in shallow marginal and nearshore marine environment influenced by waves and storms representing interactive shelf to fluvio-marine conditions. The main seal rocks are the Campanian Sirte shale deposited in a major flooding events during sea level rise. It is contended that the syn-depositional tectonics controlled the distribution of the reservoir facies in time and space. In addition, the post-depositional changes controlled the reservoir quality and performance. Petrophysical interpretation from the porosity log values were confirmed by the conventional core measurements of the different sandstone lithofacies types. Porosity ranges from 5 to 20% and permeability is between 0 and 20 mD. Petrophysical cut-off summary of the lower part of the clastic dominated sequence (i. e. Arshad Sandstone) calculated from six wells includes net pay sand ranging from 19.5‧ to 202.05‧, average porosity from 7.7 to 15% and water saturation from 19 to 58%.

  12. Growth Kinematics of Opening-Mode Fractures

    Science.gov (United States)

    Eichhubl, P.; Alzayer, Y.; Laubach, S.; Fall, A.

    2014-12-01

    Fracture aperture is a primary control on flow in fractured reservoirs of low matrix permeability including unconventional oil and gas reservoirs and most geothermal systems. Guided by principles of linear elastic fracture mechanics, fracture aperture is generally assumed to be a linear function of fracture length and elastic material properties. Natural opening-mode fractures with significant preserved aperture are observed in core and outcrop indicative of fracture opening strain accommodated by permanent solution-precipitation creep. Fracture opening may thus be decoupled from length growth if the material effectively weakens after initial elastic fracture growth by either non-elastic deformation processes or changes in elastic properties. To investigate the kinematics of fracture length and aperture growth, we reconstructed the opening history of three opening-mode fractures that are bridged by crack-seal quartz cement in Travis Peak Sandstone of the SFOT-1 well, East Texas. Similar crack-seal cement bridges had been interpreted to form by repeated incremental fracture opening and subsequent precipitation of quartz cement. We imaged crack-seal cement textures for bridges sampled at varying distance from the tips using scanning electron microscope cathodoluminescence, and determined the number and thickness of crack-seal cement increments as a function of position along the fracture length and height. Observed trends in increment number and thickness are consistent with an initial stage of fast fracture propagation relative to aperture growth, followed by a stage of slow propagation and pronounced aperture growth. Consistent with fluid inclusion observations indicative of fracture opening and propagation occurring over 30-40 m.y., we interpret the second phase of pronounced aperture growth to result from fracture opening strain accommodated by solution-precipitation creep and concurrent slow, possibly subcritical, fracture propagation. Similar deformation

  13. Biodegradation of phenols in a sandstone aquifer under aerobic conditions and mixed nitrate and iron reducing conditions

    DEFF Research Database (Denmark)

    Broholm, Mette; Arvin, Erik

    2000-01-01

    in the groundwater. The potential for biodegradation of the phenols in the sandstone aquifer at the site has been investigated in laboratory microcosms under aerobic (oxygen amended) and mixed nitrate and iron reducing (nitrate enriched and unamended) anaerobic conditions, at a range of concentrations (low: similar...... to 5 mg 1(-1): high: similar to 60 mg 1(-1), and very high: similar to 600 mg 1(-1)) and in the presence of other organic coal-tar compounds (mono- and polyaromatic hydrocarbons (BTEXs and PAHs) and heterocyclic compounds (NSOs)) and ammonia liquor. Sandstone cores and groundwater for the microcosms...

  14. A Effect discussion of transient electromagnetic sounding technique in paleochannel-type sandstone-hosted uranium deposit

    International Nuclear Information System (INIS)

    Yang Jianchun; Fang Genxian; Yang Yaxin

    2003-01-01

    On the base of the application of transient electromagnetic technique of paleochannel-type sandstone-hosted uranium deposits in Tengchong region of Yunan Province, this paper analyses the detect example. It discusses the theory foundation of TEM, fieldwork means, data processing and interpret. By contrast with routine electricity farad, the transient electromagnetic technique have the special merit and favorable space resolve gender under conditions of intricacy terrain. This means can get good effect in detecting paleochannel-type sandstone-hosted uranium deposits space position. It is a good reference for other prospecting and exploration work

  15. Metallogenic geologic prerequisites of sandstone-type uranium deposits and target area selection. Taking Erlian and Ordos basins as examples

    International Nuclear Information System (INIS)

    Chen Fazheng

    2002-01-01

    Sandstone-type uranium deposit is the main target of recent uranium prospecting and exploration. According to the metallogenic characteristics, sandstone-type uranium deposits are divided into three groups: paleo-channel type, interlayer oxidation zone type and phreatic interlayer oxidation type. The author makes an analysis on the geologic prerequisites of the three types of uranium deposits, the similarities and difference, and preliminarily summarizes genetic models of different types of uranium deposits. Finally, taking Erlian and Ordos basins as examples, the author makes an evaluation and a strategic analysis on the uranium metallogenic prospect of the above two basins

  16. Importance of dust storms in the diagenesis of sandstones: a case study, Entrada sandstone in the Ghost Ranch area, New Mexico, USA

    Science.gov (United States)

    Orhan, Hükmü

    1992-04-01

    The importance of dust storms on geological processes has only been studied recently. Case-hardening, desert-varnish formation, duricrust development, reddening and cementation of sediments and caliche formation, are some important geological processes related to dust storms. Dust storms can also be a major source for cements in aeolian sandstones. The Jurassic aeolian Entrada Formation in the Ghost Ranch area is composed of quartz with minor amounts of feldspar and rock fragments, and is cemented with smectite as grain coatings and calcite and kaolinite as pore fillings. Smectite shows a crinkly and honeycomb-like morphology which points to an authigenic origin. The absence of smectite as framework grains and the presence of partially dissolved grains, coated with smectite and smectite egg-shells, indicate an external source. Clay and fine silt-size particles are believed to be the major source for cements, smectite and calcite in the Entrada Formation. The common association of kaolinite with altered feldspar, and the absence of kaolinite in spots heavily cemented with calcite, lead to the conclusions that the kaolinite formation postdates carbonates and that framework feldspar grains were the source of kaolinite.

  17. Open Source, Open Access, Open Review, Open Data. Initiativen zu mehr Offenheit in der digitalen Welt

    OpenAIRE

    Herb, Ulrich

    2011-01-01

    The article discusses the principles of openess, open access and open availability of information based on the examples of open access to scientific information, open government data, open geographical data and open source software.

  18. Open areas and open access

    International Nuclear Information System (INIS)

    Thorndike, A.M.

    1979-01-01

    The main objective of the two open areas in the present ISABELLE design has been to provide flexibility with respect to the size and shape of experimental equipment that would eventually be installed there. No permanent building would be installed initially. One possibility would be to enclose each experiment in a temporary structure that would provide weatherproofing and shielding; another possibility would be to erect a permanent building at a later time, when experience has made the needs clearer than they are at present. The secondary objective of the design of open areas has been to keep initial costs as low as practicable. Another objective might be added, however, which we indicate by the term ''open access.'' This note will explore this idea and some design concepts based on it. In the ISABELLE 1977 summer workshop there was considerable discussion of the importance of techniques for inserting large pieces of experimental equipment quickly and removing them with equal ease and speed. Since enclosed halls have certain restrictions in this respect, open areas may be helpful in providing this feature. If the mechanical and electrical aspects could be handled quickly, one might even attempt to reduce the time spent on bureaucratic procedures in order to expedite the introduction of new experiments and new ideas in these areas

  19. OpenAPC. Open-Access-Publikationskosten als Open Data

    OpenAIRE

    Tullney, Marco

    2015-01-01

    Präsentationsfolien zum Vortrag „OpenAPC. Open-Access-Publikationskosten als Open Data“ in der Session „Ausgestaltung eines wissenschaftsadäquaten APC-Marktes: Grundsätze, Finanzierungsansätze und Management“ der Open-Access-Tage 2015 in Zürich (https://www.open-access.net/community/open-access-tage/open-access-tage-2015-zuerich/programm/#c1974)

  20. Opening remarks

    International Nuclear Information System (INIS)

    Kyd, D.R.

    1993-11-01

    In his opening remarks Mr. David R. Kyd briefly described the IAEA mission. Then he outlined main aim of the seminar which is bring together journalists, educators, officials and other specialists to let them hear and put questions to experts on various aspects of nuclear energy and techniques. Further he analyzed problems and prospects of energy development in Asia and particularly in China, including environmental considerations. The final part of the remarks was devoted comparative evaluation of different energy production technologies

  1. Open Pneumothorax

    Directory of Open Access Journals (Sweden)

    Bart Paull

    2017-07-01

    Full Text Available History of present illness: A 27-year-old male was transported to the emergency department by emergency medical services after crashing his motorcycle into a guardrail. Upon presentation he was alert, normotensive, and tachypneic. Significant findings: A large chest wound was clinically obvious. A chest radiograph performed after intubation showed subcutaneous emphysema, an anterior rib fracture, and a right-sided pneumothorax. He was then taken to the operating room for further management. Discussion: Thoracic injuries are responsible for one-quarter of all trauma-related deaths. Following rib fracture, pneumothorax is the second most common thoracic injury, occurring in 30% of patients with thoracic trauma. An open pneumothorax occurs when a chest wall injury results in direct communication between the atmosphere and pleura.1-2 It is estimated that open pneumothorax occurs in 80% of all penetrating chest wounds, with stab wounds being more common than gunshot wounds or impalement. Open pneumothoraces can lead to ventilatory insufficiency and rapid respiratory decompensation.2 Advanced Trauma Life Support recommends that the initial management of an open pneumothorax is placement of an occlusive dressing taped on three sides to create a ‘flutter-valve’ mechanism. This should then be followed by tube thoracostomy and repair of the chest wall defect.3 The placement of an occlusive dressing or initial wound closure without subsequent tube thoracostomy may result in the development of a tension pneumothorax.2 The patient was intubated and mechanical ventilation was initiated without complication. Due to the large size of the wound, an occlusive dressing was not placed in the emergency department and the patient was rapidly transported to the operating room for further management. In the operating room two chest tubes were placed. Operative findings included a right hemopneumothorax, multiple rib fractures, and a manubrial fracture. After

  2. Opening address

    International Nuclear Information System (INIS)

    Ianko, L.

    1993-01-01

    This short talk was the opening remarks to the attendees at this conference, presented by the Scientific Secretary, IWG-LMNPP, of the IAEA. This meeting is an effort to aid research on problems related to the general area of nuclear plant aging and life management. In particular it addresses fracture properties of reactor materials and components, both as installed, and at end of service condition. A major concern is relating measurements made on laboratory samples to properties displayed by actual reactor components

  3. The effect of predictability on subjective duration.

    Directory of Open Access Journals (Sweden)

    Vani Pariyadath

    2007-11-01

    Full Text Available Events can sometimes appear longer or shorter in duration than other events of equal length. For example, in a repeated presentation of auditory or visual stimuli, an unexpected object of equivalent duration appears to last longer. Illusions of duration distortion beg an important question of time representation: when durations dilate or contract, does time in general slow down or speed up during that moment? In other words, what entailments do duration distortions have with respect to other timing judgments? We here show that when a sound or visual flicker is presented in conjunction with an unexpected visual stimulus, neither the pitch of the sound nor the frequency of the flicker is affected by the apparent duration dilation. This demonstrates that subjective time in general is not slowed; instead, duration judgments can be manipulated with no concurrent impact on other temporal judgments. Like spatial vision, time perception appears to be underpinned by a collaboration of separate neural mechanisms that usually work in concert but are separable. We further show that the duration dilation of an unexpected stimulus is not enhanced by increasing its saliency, suggesting that the effect is more closely related to prediction violation than enhanced attention. Finally, duration distortions induced by violations of progressive number sequences implicate the involvement of high-level predictability, suggesting the involvement of areas higher than primary visual cortex. We suggest that duration distortions can be understood in terms of repetition suppression, in which neural responses to repeated stimuli are diminished.

  4. Understanding creep in sandstone reservoirs - theoretical deformation mechanism maps for pressure solution in granular materials

    Science.gov (United States)

    Hangx, Suzanne; Spiers, Christopher

    2014-05-01

    Subsurface exploitation of the Earth's natural resources removes the natural system from its chemical and physical equilibrium. As such, groundwater extraction and hydrocarbon production from subsurface reservoirs frequently causes surface subsidence and induces (micro)seismicity. These effects are not only a problem in onshore (e.g. Groningen, the Netherlands) and offshore hydrocarbon fields (e.g. Ekofisk, Norway), but also in urban areas with extensive groundwater pumping (e.g. Venice, Italy). It is known that fluid extraction inevitably leads to (poro)elastic compaction of reservoirs, hence subsidence and occasional fault reactivation, and causes significant technical, economic and ecological impact. However, such effects often exceed what is expected from purely elastic reservoir behaviour and may continue long after exploitation has ceased. This is most likely due to time-dependent compaction, or 'creep deformation', of such reservoirs, driven by the reduction in pore fluid pressure compared with the rock overburden. Given the societal and ecological impact of surface subsidence, as well as the current interest in developing geothermal energy and unconventional gas resources in densely populated areas, there is much need for obtaining better quantitative understanding of creep in sediments to improve the predictability of the impact of geo-energy and groundwater production. The key problem in developing a reliable, quantitative description of the creep behaviour of sediments, such as sands and sandstones, is that the operative deformation mechanisms are poorly known and poorly quantified. While grain-scale brittle fracturing plus intergranular sliding play an important role in the early stages of compaction, these time-independent, brittle-frictional processes give way to compaction creep on longer time-scales. Thermally-activated mass transfer processes, like pressure solution, can cause creep via dissolution of material at stressed grain contacts, grain

  5. Exploration for sandstone- type uranium mineralisation in the Siwaliks of northwestern Himalaya, India

    International Nuclear Information System (INIS)

    Swarnkar, B.M.; Kothari, P.K.; Umamaheswar, K.; Srinivasan, S.

    2002-01-01

    The Siwalik Group with a thickness of about 6000m of fluvial sediments of middle Miocene to Pleistocene age has been explored extensively over two decades for U, using various types of exploration techniques involving air-borne gamma-ray spectrometry, radiation jeep survey, hydrogeochemical survey, ground radiometric survey, radon survey, exploratory drilling and mining, Exploration effort by the Atomic Minerals Directorate for Exploration and Research (AMD) has helped in identifying numerous uranium occurrences spread over the entire Siwalik belt between Poonch (Jammu and Kashmir) in the west and Tanakpur (Uttar Pradesh) in the east, in the northwest Himalaya. Eight significant zones were delineated, mostly confining to distinct stratigraphic horizons of the transition zone between Middle and Upper Siwaliks, and occasionally the transition zone between Lower and Middle Siwaliks. These mineralised zones have a considerable lateral extent of up to 12 km and are associated with sandstones and rarely conglomerates. Uranium mineralisation occurs in the form of peneconcordant lensoidal bodies with individual lenses traceable from a few tens of metres to 700m, sub-parallel to strike or dip, with average grades varying from 0.020 - 0.060% U 3 O 8 and thickness less than a metre to 4m. The host rock of uranium mineralisation is predominantly sandstone containing carbonaceous matter, pyrite and clay pellets. The sandstone is often arkosic and micaceous, and termed as lithic wacke and arkosic wacke. The uranium minerals present are uraninite, pitchblende, coffinite and secondary minerals such as tyuyamunite, metatyuyamunite, uranophane, bayleyite, andersonite, schoepite, liebegite, swartzite, schroekingerite, wulfenite, billictite, betauranophane, autunite and torbernite. Relatively higher concentrations or Se, Mo, Cu, Co, V and Au have been noted in a few uranirerous zones. Concentration or uranium in the Siwalik clastic sediments is controlled by the redox interface

  6. Selective sandstone deterioration in the cathedrals of Salamanca, Textural anisotropy as a cause

    Directory of Open Access Journals (Sweden)

    Martín Patino, María Teresa

    1994-09-01

    Full Text Available Textural sandstone anisotropy is related to the selective deterioration of such stone in buildings. The samples studied come from the Cathedrals of Salamanca. Stone fragments, cut in different directions with regard to the base supporting the ashlars in the wall, are studied by means of a binocular magnifying glass and the Scanning Electron Microscopy (SEM. This shows that the sandstone microfabric has a granular and a laminar microtexture, which correspond to different directions in the plane in question as regards the position of the ashlar. Either of these circumstances coincides with the stone surface on the outside of the building and affect its surface deterioration in a different way. The SEM images of deteriorated stone were compared with those of unaffected stone, with both types coming from differently orientated cuts as regards the position of the ashlar. In conclusion, the position given to the block of stone in the building is of importance for the preservation of the stone. The speed of ultrasound transmission measured in samples from commercial quarries confirms the textural sandstone anisotropy to a greater or lesser extent.

    La anisotropía textural de las areniscas se relaciona con la selectividad de su deterioro en los edificios. Las muestras estudiadas pertenecen a las Catedrales de Salamanca. Fragmentos de piedra, cortados en direcciones diferentes respecto a la base sobre la que se asientan los sillares en el muro, son estudiados por medio de la lupa binocular y del microscopio electrónico de barrido (SEM. De éstos se deduce que la microfábrica de las areniscas tiene una microtextura granular y otra laminar, que corresponden a direcciones diferentes del plano respecto al asiento del sillar. Una u otra de estas situaciones coincide con la superficie de la piedra expuesta al exterior en el edificio, y afectan a su deterioro superficial de forma diferente. Las capas externas en las que predomina la arcilla

  7. The experimental modeling of gas percolation mechanisms in a coal-measure tight sandstone reservoir: A case study on the coal-measure tight sandstone gas in the Upper Triassic Xujiahe Formation, Sichuan Basin, China

    Directory of Open Access Journals (Sweden)

    Shizhen Tao

    2016-12-01

    Full Text Available Tight sandstone gas from coal-measure source rock is widespread in China, and it is represented by the Xujiahe Formation of the Sichuan Basin and the Upper Paleozoic of the Ordos Basin. It is affected by planar evaporative hydrocarbon expulsion of coal-measure source rock and the gentle structural background; hydrodynamics and buoyancy play a limited role in the gas migration-accumulation in tight sandstone. Under the conditions of low permeability and speed, non-Darcy flow is quite apparent, it gives rise to gas-water mixed gas zone. In the gas displacing water experiment, the shape of percolation flow curve is mainly influenced by core permeability. The lower the permeability, the higher the starting pressure gradient as well as the more evident the non-Darcy phenomenon will be. In the gas displacing water experiment of tight sandstone, the maximum gas saturation of the core is generally less than 50% (ranging from 30% to 40% and averaging at 38%; it is similar to the actual gas saturation of the gas zone in the subsurface core. The gas saturation and permeability of the core have a logarithm correlation with a correlation coefficient of 0.8915. In the single-phase flow of tight sandstone gas, low-velocity non-Darcy percolation is apparent; the initial flow velocity (Vd exists due to the slippage effect of gas flow. The shape of percolation flow curve of a single-phase gas is primarily controlled by core permeability and confining pressure; the lower the permeability or the higher the confining pressure, the higher the starting pressure (0.02–0.08 MPa/cm, whereas, the higher the quasi-initial flow speed, the longer the nonlinear section and the more obvious the non-Darcy flow will be. The tight sandstone gas seepage mechanism study shows that the lower the reservoir permeability, the higher the starting pressure and the slower the flow velocity will be, this results in the low efficiency of natural gas migration and accumulation as well as

  8. Open access, open education resources and open data in Uganda ...

    African Journals Online (AJOL)

    As a follow up to OpenCon 2014, International Federation of Medical Students' Associations (IFMSA) students organized a 3 day workshop Open Access, Open Education Resources and Open Data in Kampala from 15-18 December 2014. One of the aims of the workshop was to engage the Open Access movement in ...

  9. Open areas and open access

    International Nuclear Information System (INIS)

    Thorndike, A.M.

    1978-01-01

    One objective of the two open areas in the present ISABELLE design is to provide flexibility with respect to the size and shape of experimental equipment that would eventually be installed there. No permanent building would be installed initially. A second objective of the design of open areas is to keep initial costs as low as practicable. Another objective is open access. This note explores this idea and some design concepts based on it. It would permit inserting large pieces of experimental equipment quickly and removing them with equal ease and speed. Entire experiments would be moved in a single piece (or a few) by building them on movable platforms with capacities of up to about 1000 tons per platform. Most experiments could be built on a single platform or on a few. The shielding must also be moved. It must also be organized into a small number of large units. A scheme using large tanks filled with water is described. It is important to make the equipment on a given platform as complete and self-contained as possible, with a minimum of interconnections for power, coolant, controls, data transmission, etc. 5 figures

  10. Opening remarks

    International Nuclear Information System (INIS)

    Southwood, Richard

    1987-01-01

    General opening remarks to a conference on the effects of low-level radiation on man, exploring particularly areas where disagreements have most frequently been voiced. The author comments on two approaches: a) the study, stepwise of putative cause and effect chains, using models which are tested by comparing calculated and observed effects. b) the epidemiological approach by extensive correlative study of cause, correlations and effect. Attention is drawn to the confidence to be accorded to any quantitative theory supported by both approaches, and the need for further analysis if the approaches give different indications. (U.K.)

  11. Open University

    CERN Multimedia

    Pentz,M

    1975-01-01

    Michel Pentz est née en Afrique du Sud et venu au Cern en 1957 comme physicien et président de l'associaion du personnel. Il est également fondateur du mouvement Antiapartheid de Genève et a participé à la fondation de l'Open University en Grande-Bretagne. Il nous parle des contextes pédagogiques, culturels et nationaux dans lesquels la méthode peut s'appliquer.

  12. Opening lecture

    International Nuclear Information System (INIS)

    Thomas, J.B.

    1997-01-01

    The opening lecture on the results of fifty years in the nuclear energy field, deals with the main principles underlying the CEA policy concerning the fission nuclear energy transformation, i.e. the design of a nuclear industry that is a safe, high-performance and reliable source of electric power, the development of an adaptive power generation tool with the capacity to progress according to new constraints, and the necessary anticipation for preparing to the effects of the next 50 year technological leaps

  13. Sandstone uranium deposits in the United States: a review of the history, distribution, genesis, mining areas, and outlook

    International Nuclear Information System (INIS)

    Crawley, R.A.

    1983-03-01

    Sandstone uranium deposits account for about 94 percent of uranium reserves in the United States. Most sandstone uranium districts had been found by the mid-1950s in response to incentives promulgated by the US Atomic Energy Commission. Principal uranium resource regions in the United States are the Colorado Plateau, Wyoming Basins, and Texas Coastal Plain. Statistical data published annually by the US Department of Energy show trends of uranium exploration and production, estimates of resources, and distributions and characteristics of reserves. At present, US exploration and production are curtailed because of uranium oversupply, a trend that will continue for the next few years. Although the outlook is more optimistic over the longer term, it is clouded by possible competition from foreign low-cost, nonsandstone uranium. Roll-type and peneconcordant are the two principal types of sandstone uranium deposits. Roll deposits are formed at geochemical fronts where oxidizing uranium-bearing groundwater penetrates reduced sandstone. Uranium is precipitated by reduction at the front. Under mildly reducing conditions, uranium may remain in solution until it is locally precipitated by reduction, chelation, or complexing to form peneconcordant deposits. Proposed precipitating agents include carbonaceous matter, humate, pyrite, and hydrogen sulfide. The uranium is thought to have been derived from leaching of tuffaceous or arkosic sediments, or of granitic rocks

  14. A method for automatic grain segmentation of multi-angle cross-polarized microscopic images of sandstone

    Science.gov (United States)

    Jiang, Feng; Gu, Qing; Hao, Huizhen; Li, Na; Wang, Bingqian; Hu, Xiumian

    2018-06-01

    Automatic grain segmentation of sandstone is to partition mineral grains into separate regions in the thin section, which is the first step for computer aided mineral identification and sandstone classification. The sandstone microscopic images contain a large number of mixed mineral grains where differences among adjacent grains, i.e., quartz, feldspar and lithic grains, are usually ambiguous, which make grain segmentation difficult. In this paper, we take advantage of multi-angle cross-polarized microscopic images and propose a method for grain segmentation with high accuracy. The method consists of two stages, in the first stage, we enhance the SLIC (Simple Linear Iterative Clustering) algorithm, named MSLIC, to make use of multi-angle images and segment the images as boundary adherent superpixels. In the second stage, we propose the region merging technique which combines the coarse merging and fine merging algorithms. The coarse merging merges the adjacent superpixels with less evident boundaries, and the fine merging merges the ambiguous superpixels using the spatial enhanced fuzzy clustering. Experiments are designed on 9 sets of multi-angle cross-polarized images taken from the three major types of sandstones. The results demonstrate both the effectiveness and potential of the proposed method, comparing to the available segmentation methods.

  15. Anisotropy of sandstone reservoir and shale overburden estimated from spherical sample measurements and cross-dipole logging

    Czech Academy of Sciences Publication Activity Database

    Lokajíček, Tomáš; Brajanovski, M.; Gurevich, B.; Bona, A.; Nadri, D.; Urosevic, M.; Duncan, G.

    2009-01-01

    Roč. 11, - (2009), s. 4956-4956 ISSN 1029-7006. [European Geosciences Union General Assembly. 19.04.2009-24.04.2009, Vienna] R&D Projects: GA ČR GA205/08/0676 Institutional research plan: CEZ:AV0Z30130516 Keywords : anisotropy * sandstones * rocks Subject RIV: DB - Geology ; Mineralogy

  16. Hydrocarbon Potential in Sandstone Reservoir Isolated inside Low Permeability Shale Rock (Case Study: Beruk Field, Central Sumatra Basin)

    Science.gov (United States)

    Diria, Shidqi A.; Musu, Junita T.; Hasan, Meutia F.; Permono, Widyo; Anwari, Jakson; Purba, Humbang; Rahmi, Shafa; Sadjati, Ory; Sopandi, Iyep; Ruzi, Fadli

    2018-03-01

    Upper Red Bed, Menggala Formation, Bangko Formation, Bekasap Formation and Duri Formationare considered as the major reservoirs in Central Sumatra Basin (CSB). However, Telisa Formation which is well-known as seal within CSB also has potential as reservoir rock. Field study discovered that lenses and layers which has low to high permeability sandstone enclosed inside low permeability shale of Telisa Formation. This matter is very distinctive and giving a new perspective and information related to the invention of hydrocarbon potential in reservoir sandstone that isolated inside low permeability shale. This study has been conducted by integrating seismic data, well logs, and petrophysical data throughly. Facies and static model are constructed to estimate hydrocarbon potential resource. Facies model shows that Telisa Formation was deposited in deltaic system while the potential reservoir was deposited in distributary mouth bar sandstone but would be discontinued bedding among shale mud-flat. Besides, well log data shows crossover between RHOB and NPHI, indicated that distributary mouth bar sandstone is potentially saturated by hydrocarbon. Target area has permeability ranging from 0.01-1000 mD, whereas porosity varies from 1-30% and water saturation varies from 30-70%. The hydrocarbon resource calculation approximates 36.723 MSTB.

  17. Petrological features of selected components of the Cergowa sandstones (Outer Carpathians) recorded by scanning electron microscopy - preliminary study

    Science.gov (United States)

    Pszonka, Joanna

    2017-11-01

    The scanning electron microscope analysis of the Cergowa sandstones brings new data on their petrological features and chemical composition. Previous work in standard petrographic examination, e.g. polarising (PL) or cathodoluminescence (CL) microscopy, displayed limited information on grain surface topography and only assumptions to their geochemistry. Both identification and characterisation of minerals are fundamental in the progress of mining and minerals processing systems. Detrital grains of the Cergowa sandstones are bound by calcite and dolomitic cement and commonly corroded by diagenetic fluids, however, in varying degrees, which is illustrated here by feldspar, quartz and dolomite minerals. Dissolution processes of marginal parts of these mineral grains resulted in corrosion, which increased the contact surface between the grains and the cement. The difference in resistance to these processes was observed not only among distinct groups of minerals, but also within the group of feldspars: between K-feldspars and minerals of plagioclase. That combination resulted in exceptionally strong cementation of the Cergowa sandstones, which is expressed by their high hardness and resistance to abrasion, freezing, and thawing. Inherent parameters of sandstones are characterised by their petrographical properties.

  18. Petrological features of selected components of the Cergowa sandstones (Outer Carpathians recorded by scanning electron microscopy – preliminary study

    Directory of Open Access Journals (Sweden)

    Pszonka Joanna

    2017-01-01

    Full Text Available The scanning electron microscope analysis of the Cergowa sandstones brings new data on their petrological features and chemical composition. Previous work in standard petrographic examination, e.g. polarising (PL or cathodoluminescence (CL microscopy, displayed limited information on grain surface topography and only assumptions to their geochemistry. Both identification and characterisation of minerals are fundamental in the progress of mining and minerals processing systems. Detrital grains of the Cergowa sandstones are bound by calcite and dolomitic cement and commonly corroded by diagenetic fluids, however, in varying degrees, which is illustrated here by feldspar, quartz and dolomite minerals. Dissolution processes of marginal parts of these mineral grains resulted in corrosion, which increased the contact surface between the grains and the cement. The difference in resistance to these processes was observed not only among distinct groups of minerals, but also within the group of feldspars: between K–feldspars and minerals of plagioclase. That combination resulted in exceptionally strong cementation of the Cergowa sandstones, which is expressed by their high hardness and resistance to abrasion, freezing, and thawing. Inherent parameters of sandstones are characterised by their petrographical properties.

  19. Analysis of leachability for a sandstone uranium deposite with high acid consumption and sensitivities in Inner Mongolia

    International Nuclear Information System (INIS)

    Cheng Wei; Miao Aisheng; Li Jianhua; Zhou Lei; Chang Jingtao

    2014-01-01

    In-situ Leaching adaptability of a ground water oxidation zone type sandstone uranium deposit from Inner Mongolia is studied. The ore of the uranium deposit has high acid consumption and sensitivities in in-situ leaching. The leaching process with agent of CO_2 + O_2 and adjusting concentration of HCO_3"- can be suitable for the deposit. (authors)

  20. Preliminary discussion on prospecting potential for sandstone-type uranium deposits in meso-cenozoic basins, northern Ordos

    International Nuclear Information System (INIS)

    Di Yongqiang

    2002-01-01

    Characteristics of the regional stratigraphy, tectonic movement, geologic evolution and hydrogeology are briefly introduced. Using the metallogenic theory and prospecting criteria for interlayer oxidation zone sandstone-type uranium deposits, the author analyses the prospecting potential and main prospecting targets in the region, and proposes suggestions for further prospecting work as well

  1. Isotopic composition of salt efflorescence from the sandstone castellated rocks of the Bohemian Cretaceous Basin (Czech Republic)

    Czech Academy of Sciences Publication Activity Database

    Schweigstillová, Jana; Přikryl, R.; Novotná, M.

    2009-01-01

    Roč. 58, č. 1 (2009), s. 217-225 ISSN 0943-0105 Institutional research plan: CEZ:AV0Z30460519 Keywords : stable isotopes * salt efflorescence * sandstone Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.078, year: 2009

  2. Cyclicity recorded in the provenance sandstones in the sedimentary in fill of the Cameros basin (N. Spain)

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez-Acebron, L.; Arribas, J.; Omodeo-Sale, S.; Arribas, E.; Le Pera, E.; Mas, R.; Lopez-Elorza, M.; Fernandez-Diaz, P. R.

    2013-06-01

    The intra plate Cameros rift basin in the north of Spain was formed came into being between the Tithonian and the Early Albian and contains 9 000 m of mostly continental sediments. This basin is a good example of cyclicity of different depositional sequences (DSs) in sedimentary environments, which show clear repetition in their sandstone composition (petrofacies) and diagenetic patterns. The DSs are arranged in two mega sequences (MSs) separated by a tectonic unconformity. A similar vertical sandstone compositional evolution, subdivided into two stages that repeat cyclically, has been recognised in both MSs: the first comprises quartzo-sedimentolithic petrofacies and the second is made up of several quartzo-feldspathic petrofacies. This was caused by a progression from the recycling of the pre-rift sedimentary cover to the erosion of the mainly plutonic and metamorphic crystalline basement. These changes in the erosion of the different source areas were conditioned by the tectonics of the basin. Furthermore, the original sandstone framework composition conditioned the diagenetic pattern of the two stages: quartzo-sedimentolithic sandstones containing large amounts of very pervasive carbonate cement that reduce their original porosity considerably, and quartzo-feldspathic petrofacies with a rigid framework that maintained the original pores during burial diagenesis. This compositional and diagenetic pattern is probably applicable to other non-volcanic rifted basins, depending upon the original amount of carbonate rock fragments present. (Author)

  3. Elastic moduli of sandstones saturated with a range of pore fluids correlated with kinematic viscosity and frequency ratio

    DEFF Research Database (Denmark)

    Sørensen, Morten Kanne; Fabricius, Ida Lykke

    2011-01-01

    . The purpose of this study is to investigate if frame parameters can be extracted from air saturated measurements in sandstones, because earlier studies have shown that air may have a non-negligible effect on carbonates due to the high kinematic viscosity of air (Fabricius et al., 2010)....

  4. Application of base-level cycles to sandstone-type uranium deposit: taking Dongsheng uranium deposits as an example

    International Nuclear Information System (INIS)

    Yang Renchao; Han Zuozhen; Fan Aiping; Chang Xiangchun

    2006-01-01

    High-resolution sequence stratigraphy taking base-level cycles as interface of reference was developed rapidly in recent years. Its greatest predominance lies in that it can be applied to multi-controled continental sedimentary basins and can effectively improve accuracy and distinguishability of sequence stratigraphy analysis. Principles of base-level cycles can also be applied to the research and practice of the exploration and exploitation of sandstone-type uranium deposits as they control the spatial distribution, porosity, the permeability and the sealing ability of sandstone and mudstone, and stacking patterns of strata configuration. Taking Dongsheng uranium deposits as an example, the application of base-level cycles to exploration and exploitation of sandstone uranium deposits was analyzed. It is suggested that favorable strata framework of sandstone and mudstone was developed very well in the fluctuation of base-level cycles. Sand bodies were provided with good connectedness, coarse granularity, high debris content, low matrix content and good porosity-permeability becoming the most important uranium hosted strata. (authors)

  5. Digitization of uranium deposit information in basin. A new strategy of ISL sandstone-type uranium deposits exploration

    International Nuclear Information System (INIS)

    Tan Chenglong

    2006-01-01

    The discovered ISL sandstone-type uranium deposits in the entire world are mostly blind deposits, many of them occur in bleak desert, gobi desert, and semi-hilly land area. Exploration methods for these deposits mainly depend on great and systematic drilling. There are many large-medium size Meso-Cenozoic sedimentary basins in northern China, and over twenty of them are thick overburden basins which are mostly the virgin land for ISL sandstone-type uranium deposit. Due to the comprehensive national power, geological background, uranium exploration ability, great and systematic drilling is not favorable for prospecting ISL sandstone-type uranium deposit in China. According to the exploration and prospecting experiences for mineral ore bodies at home and abroad, uranium information mapping based on geochemical survey of the basins is a new strategy for ISL sandstone-type uranium deposits. It is an economic, practical, fast and effective method, and has been manifested by the performing information digitization for oil and gas resources, gold mineral resources in China and the mapping of uranium information for whole Europe continent. (authors)

  6. Geology and recognition criteria for sandstone uranium deposits in mixed fluvial-shallow marine sedimentary sequences, South Texas. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Adams, S.S.; Smith, R.B.

    1981-01-01

    Uranium deposits in the South Texas Uranium Region are classical roll-type deposits that formed at the margin of tongues of altered sandstone by the encroachment of oxidizing, uraniferous solutions into reduced aquifers containing pyrite and, in a few cases, carbonaceous plant material. Many of the uranium deposits in South Texas are dissimilar from the roll fronts of the Wyoming basins. The host sands for many of the deposits contain essentially no carbonaceous plant material, only abundant disseminated pyrite. Many of the deposits do not occur at the margin of altered (ferric oxide-bearing) sandstone tongues but rather occur entirely within reduced, pyurite-bearing sandstone. The abundance of pyrite within the sands probably reflects the introduction of H/sub 2/S up along faults from hydrocarbon accumulations at depth. Such introductions before ore formation prepared the sands for roll-front development, whereas post-ore introductions produced re-reduction of portions of the altered tongue, leaving the deposit suspended in reduced sandstone. Evidence from three deposits suggests that ore formation was not accompanied by the introduction of significant amounts of H/sub 2/S.

  7. Morphology of channels and channel-sand bodies in the Glauconitic sandstone member (Upper Mannville), Little Bow area, Alberta

    Energy Technology Data Exchange (ETDEWEB)

    Hopkins, J.C.; Hermanson, S.W.; Lawton, D.C.

    1982-12-01

    Large channels in the Glauconitic sandstone member of southern Alberta have proved to be difficult exploration targets because of an irregular distribution of reservoir sands within the channels. In the Little Bow area, two channels are present in the lower part of the Glauconitic member and have cut into the underlying Calcareous member. The channels can be recognized where they truncate regional markers of the Calcareous member -- the Bantry shale and Ostracod limestone, and where channel-fill deposits exhibit uniform geophysical log characters, indicating sandstone- or mudstone-filled reaches. Sediments of the Glauconitic member adjacent to the channels comprise a series of splay sandstones and mudstones that prograded into interdistributary bays of the lower delta plain. The two channels associated with these deposits are interpreted as distributary channels. Sand bodies within the channels formed as lateral bars and are isolated by mudstones which mark the abandoned stream course. Geological exploration for these discontinuous channel sandstones is difficult, and high-resolutio seismic data integrated with sound geologic modelling are critical for successful prospect delineation.

  8. Experimental study and theoretical interpretation of saturation effect on ultrasonic velocity in tight sandstones under different pressure conditions

    Science.gov (United States)

    Li, Dongqing; Wei, Jianxin; Di, Bangrang; Ding, Pinbo; Huang, Shiqi; Shuai, Da

    2018-03-01

    Understanding the influence of lithology, porosity, permeability, pore structure, fluid content and fluid distribution on the elastic wave properties of porous rocks is of great significance for seismic exploration. However, unlike conventional sandstones, the petrophysical characteristics of tight sandstones are more complex and less understood. To address this problem, we measured ultrasonic velocity in partially saturated tight sandstones under different effective pressures. A new model is proposed, combining the Mavko-Jizba-Gurevich relations and the White model. The proposed model can satisfactorily simulate and explain the saturation dependence and pressure dependence of velocity in tight sandstones. Under low effective pressure, the relationship of P-wave velocity to saturation is pre-dominantly attributed to local (pore scale) fluid flow and inhomogeneous pore-fluid distribution (large scale). At higher effective pressure, local fluid flow gradually decreases, and P-wave velocity gradually shifts from uniform saturation towards patchy saturation. We also find that shear modulus is more sensitive to saturation at low effective pressures. The new model includes wetting ratio, an adjustable parameter that is closely related to the relationship between shear modulus and saturation.

  9. A GIS-based model of potential groundwater yield zonation for a sandstone aquifer in the Juye Coalfield, Shangdong, China

    Science.gov (United States)

    Yin, Huiyong; Shi, Yongli; Niu, Huigong; Xie, Daolei; Wei, Jiuchuan; Lefticariu, Liliana; Xu, Shuanxiang

    2018-02-01

    Resolving the potential groundwater yield zonation of sandstone aquifers occurring at depths of several hundred meters has been an important and challenging objective of the hydrogeological research focused on preventing flood hazards in coal mines. Using accessible geological exploration data we put forward a method of predicting the spatial distribution of groundwater storage potential in sandstone aquifers from Permian-age coal deposits in Juye Coalfield, Shangdong, China. A Geological, Tectonic and Lithological Composition Index (GTLCI) model was created using the following parameters: sandstone depth and thickness, faults length density (FaLD), faults density (FaD), fault frequency density (FaFD), fault scale density (FaSD), variation coefficient of the slope (VCS) of the coal seam, intensity index of folds in horizontal direction (IIFoH), and lithological composition index (LCI). Each of these factors was subsequently divided into 5 classes. The analytic hierarchy process (AHP) and trapezoidal fuzzy number (TFN) method was applied to calculate the weight of the conditioning factor and their respective sub-classes. Groundwater yield potential contour map, which was initially constructed using the GTLCI values revealed four groundwater abundance zones. The map was further refined by taking into account hydrogeologic data collected during mining activities. The GTLCI model predictive success rate of 80% was explained by the limited number of boreholes available for validation. It is considered that the GTLCI model is effective at predicting zonation of groundwater yield in the sandstone aquifers from Permian- age coal deposits in Juye Coalfield, China.

  10. Geology and recognition criteria for sandstone uranium deposits in mixed fluvial-shallow marine sedimentary sequences, South Texas. Final report

    International Nuclear Information System (INIS)

    Adams, S.S.; Smith, R.B.

    1981-01-01

    Uranium deposits in the South Texas Uranium Region are classical roll-type deposits that formed at the margin of tongues of altered sandstone by the encroachment of oxidizing, uraniferous solutions into reduced aquifers containing pyrite and, in a few cases, carbonaceous plant material. Many of the uranium deposits in South Texas are dissimilar from the roll fronts of the Wyoming basins. The host sands for many of the deposits contain essentially no carbonaceous plant material, only abundant disseminated pyrite. Many of the deposits do not occur at the margin of altered (ferric oxide-bearing) sandstone tongues but rather occur entirely within reduced, pyurite-bearing sandstone. The abundance of pyrite within the sands probably reflects the introduction of H 2 S up along faults from hydrocarbon accumulations at depth. Such introductions before ore formation prepared the sands for roll-front development, whereas post-ore introductions produced re-reduction of portions of the altered tongue, leaving the deposit suspended in reduced sandstone. Evidence from three deposits suggests that ore formation was not accompanied by the introduction of significant amounts of H 2 S

  11. Wind-blown sandstones cemented by sulfate and clay minerals in Gale Crater, Mars

    Science.gov (United States)

    Milliken, R. E.; Ewing, R. C.; Fischer, W. W.; Hurowitz, J.

    2014-02-01

    Gale Crater contains Mount Sharp, a ~5 km thick stratigraphic record of Mars' early environmental history. The strata comprising Mount Sharp are believed to be sedimentary in origin, but the specific depositional environments recorded by the rocks remain speculative. We present orbital evidence for the occurrence of eolian sandstones within Gale Crater and the lower reaches of Mount Sharp, including preservation of wind-blown sand dune topography in sedimentary strata—a phenomenon that is rare on Earth and typically associated with stabilization, rapid sedimentation, transgression, and submergence of the land surface. The preserved bedforms in Gale are associated with clay minerals and elsewhere accompanied by typical dune cross stratification marked by bounding surfaces whose lateral equivalents contain sulfate salts. These observations extend the range of possible habitable environments that may be recorded within Gale Crater and provide hypotheses that can be tested in situ by the Curiosity rover payload.

  12. Study on extraction of uranium from clayey sandstone with floatation-leaching process

    International Nuclear Information System (INIS)

    Meng Guangshou; Zhao Manchang; Wu Peisheng; Song Wenlan; Li Wenxia.

    1985-01-01

    An improved floatation-leaching process is proposed to extract uranium from some clayey sandstone type of ore. By two-step flotation, the ground feed ore can be divided into three urani-ferous sections, i.e., the sulfidic concentrate carrying organic matter, the carbonate concentrate, and the tailings. The sulfidic concentrate is mixed with the tailings and then treated by acid-leaching with the result that 93% uranium extraction can be attained. The excess free acid of the leached slurry is further neutralized with the carbonate concentrate instead of lime commonly used. As a result, approximately 60% uranium extraction can be attained. As a whole, by the flotation-leaching process the acid consumption can be reduced from 200 kg/t down to < 80 kg/t and the uranium extraction can be raised from 85% to 90% as compared with the conventional acid-leaching process

  13. Investigation of the petrophysical properties of a porous sandstone sample using confocal scanning laser microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Petford, N. [Kingston Univ., Centre for Earth and Environmental Science Research, Kingston (United Kingdom); Davidson, G. [University Coll., Dept. of Electronic and Electrical Engineering, London (United Kingdom); Miller, J.A. [Cambridge Univ., Dept. of Earth Sciences, Cambridge (United Kingdom)

    2001-05-01

    Confocal scanning laser microscopy (CSLM) is used to produce images of the two- and three-dimensional distribution and geometry of pore space in a reservoir sandstone and measure the 2D distribution of pore throat radii. Non-destructive serial sectioning of the rock using laser light at 100% illumination, combined with image thresholding and histogram equalization techniques allow the pore volume structure of the uppermost 100 {mu}m of the sample to be reconstructed. Negative imaging of the pore volume gave superior depth and feature resolution compared to positive (reflection) imaging. Artefacts encountered in applying classical Medial Axial Transforms to CSLM images include branch networks dominated by coordination numbers of 3. Skeletonization using Euclidean distance maps gives increased accuracy in the description of the pore network. Measured pore throat size distribution in the rock is strongly exponential and described by the expression y 219e{sup -0.25x} where y is the number of pore throats. (Author)

  14. Microstructure parameters evaluation of Botucatu formation sandstone by X-ray microtomography

    Energy Technology Data Exchange (ETDEWEB)

    Fernandes, Jaquiel S.; Appoloni, Carlos R.; Marques, Leonardo C., E-mail: jaquielfernandes@yahoo.com.b, E-mail: appoloni@uel.b, E-mail: leocarma@yahoo.com.b [Universidade Estadual de Londrina (UEL), PR (Brazil). Dept. de Fisica. Lab. de Fisica Nuclear Aplicada; Fernandes, Celso P., E-mail: celso@lmpt.ufsc.b [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil). Dept. de Engenharia Mecanica. Lab. de Meios Porosos e Propriedades TermoFisicas (LMPT)

    2009-07-01

    Microstructural parameters evaluation of reservoir rocks are very important to petroleum industry. This work presents total porosity and pore size distribution measurement of a silicified sandstone sample from the Botucatu formation, collected at municipal district of Faxinal, Parana, Brazil. Porosity and pores size distribution were determined using X-Ray microtomography and imaging techniques. Acquired images had 2.9 mum spatial resolution. 800 2-D images where reconstructed for the microstructure analysis. The determined average porosity was 6.1 +- 2.1 %. 95 % of the porous phase refers to pores with radius ranging from 2.9 to 167.4 mum, presenting the larger frequency (6 %) at 5.9 mum radius. The 3-D volume of the sample was reconstructed and compared with the 3-D model obtained through the autocorrelation functions from the 2-D images analysis. (author)

  15. Study on designing a complete pilot plant for processing sandstone ores in Palua-Parong area

    International Nuclear Information System (INIS)

    Le Quang Thai; Tran Van Son; Tran The Dinh; Trinh Nguyen Quynh; Vu Khac Tuan

    2015-01-01

    Design work is the first step of the construction and operation of pilot plant. Thus, the project Study on designing a complete pilot plant for processing sandstone ores in Palua - Parong area was conducted to design a pilot plant for testing entire technological process to obtain yellowcake. Based on a literature review of uranium ore processing technology in the world, information of ore and previous research results of uranium ore in PaLua - PaRong area at the Institute for Technology of Radioactive and Rare Elements, a suitable technological flowsheet for processing this ore has been selected. The size, location of the pilot plant and planed experiments has been selected during the implementation of this project, in which basic parameters, designed system of equipment, buildings, ect. were also calculated. (author)

  16. Study on metallogenetic prospect of interlayer oxidation zone sandstone type uranium deposit in Shanganning basin

    International Nuclear Information System (INIS)

    Wang Jinping

    1998-01-01

    As Compared with orogenic zone basin, which the interlayer oxidation zone sandstone type uranium deposits are found, the Shanganning basin a continental platform type basin is distinct either in the geodynamic background and the post-basin hydrogeological evolution or in the appearance of the metallogenetic dynamics-orogenesis. The prediction criteria summarized for interlayer oxidation zone type U-deposits in Middle Asia therefore can not be completely applied in such a basin. Based on analysis of the typical regional geological setting, the hydrogeology of the Meso-Cenozoic cover is studied in detail. Three hydrogeological cycles have been divided, and prospects of uranium deposits have been clarified and the most promising target have been proposed

  17. Genetic models and their impact on uranium exploration in the Athabasca sandstone basin, Saskatchewan, Canada

    International Nuclear Information System (INIS)

    Strnad, J.G.

    1980-01-01

    While the Beaverlodge area of Northern Saskatchewan became an important uranium-producing district during the 1950s, the Athabasca sandstone basin, located in the immediate vicinity, was considered to be non-prospective in Canada's regional assessment. Twenty years later, with the introduction of the supergene model into the basin's exploration strategy, the favourability of the host-rock for uranium deposits was shown. However, in some instances the search for local targets was enriched by implementing non-supergene models. Most geologists originally favoured the Middle Proterozoic (sub-Helikian) unconformity as a unique ore-controlling feature. Later, the concept of Lower Proterozoic (Aphebian) syngenetic protore, as represented by graphite-bearing strata in Archaean proximity, was added. In the author's view the combination of these factors is productive only within specialized segments of Archaean-Lower Proterozoic (Archaean-Aphebian) contact zones. (author)

  18. Fission track dating of mesozoic sandstones and its tectonic significance in the Eastern Sichuan Basin, China

    International Nuclear Information System (INIS)

    Shen Chuanbo; Mei Lianfu; Xu Sihuang

    2009-01-01

    To establish the tectonic evolution of the eastern Sichuan basin, apatite fission track dating and time-temperature thermal history modeling were carried to analyze on 11 samples collected from Jurassic sandstones. The results indicate that the cooling and exhumation process of the eastern Sichuan basin can be divided into three stages since Cretaceous, (1) a rapid cooling phase between ∼100 and ∼70 Ma, (2) following by a period of relative thermal stability phase between ∼70 and ∼15 Ma, (3) and then a new rapid cooling stage after ∼15 Ma. Two rapid cooling events imply that the eastern Sichuan basin once underwent two tectonic movements since Cretaceous. The first rapid cooling is associated with Mesozoic tectonic reactivation beginning at 100 Ma, which result in folds and faults of the eastern Sichuan basin. The second tectonic movement occurred at 15 Ma, which is related to denudation by compression resulting from the eastward growth of Tibetan plateau uplift.

  19. Information system for sandstone uranium exploration based on Arc View 3.2

    International Nuclear Information System (INIS)

    Han Shaoyang; Hou Huiqun; Huang Shutao

    2001-01-01

    The compositive platform of the system is geographic information system software-Arc View 3.2. The secondary development has been finished through the language-AVENUE provided by Arc View 3.2. The system integrates all kinds of data, graphic information, analysis results, spatial analysis methods in data processing and integrated evaluation models during the sandstone uranium exploration. According to the need of multi-source-information management and integrated evaluation, a series of new functions was appended to the basic platform through AVENUE language on a basis of sufficiently inheriting Arc View software functions, and the friendly graphic user interface is created so that the system realizes the functions better, which include information query, data base management, graphics editing, geology cartography, model analysis and result outputs

  20. Exploration of method determining hydrogeologic parameters of low permeability sandstone uranium deposits

    International Nuclear Information System (INIS)

    Ji Hongbin; Wu Liwu; Cao Zhen

    2012-01-01

    A hypothesis of regarding injecting test as 'anti-pumping' test is presented, and pumping test's 'match line method' is used to process data of injecting test. Accurate hydrogeologic parameters can be obtained by injecting test in the sandstone uranium deposits with low permeability and small pumping volume. Taking injecting test in a uranium deposit of Xinjiang for example, the hydrogeologic parameters of main ore-bearing aquifer were calculated by using the 'anti-pumping' hypothesis. Results calculated by the 'anti-pumping' hypothesis were compared with results calculated by water level recovery method. The results show that it is feasible to use 'anti-pumping' hypothesis to calculate the hydrogeologic parameters of main ore-bearing aquifer. (authors)

  1. Dynamic fluid connectivity during steady-state multiphase flow in a sandstone.

    Science.gov (United States)

    Reynolds, Catriona A; Menke, Hannah; Andrew, Matthew; Blunt, Martin J; Krevor, Samuel

    2017-08-01

    The current conceptual picture of steady-state multiphase Darcy flow in porous media is that the fluid phases organize into separate flow pathways with stable interfaces. Here we demonstrate a previously unobserved type of steady-state flow behavior, which we term "dynamic connectivity," using fast pore-scale X-ray imaging. We image the flow of N 2 and brine through a permeable sandstone at subsurface reservoir conditions, and low capillary numbers, and at constant fluid saturation. At any instant, the network of pores filled with the nonwetting phase is not necessarily connected. Flow occurs along pathways that periodically reconnect, like cars controlled by traffic lights. This behavior is consistent with an energy balance, where some of the energy of the injected fluids is sporadically converted to create new interfaces.

  2. Pore Structure Model for Predicting Elastic Wavespeeds in Fluid-Saturated Sandstones

    Science.gov (United States)

    Zimmerman, R. W.; David, E. C.

    2011-12-01

    During hydrostatic compression, in the elastic regime, ultrasonic P and S wave velocities measured on rock cores generally increase with pressure, and reach asymptotic values at high pressures. The pressure dependence of seismic velocities is generally thought to be due to the closure of compliant cracks, in which case the high-pressure velocities must reflect only the influence of the non-closable, equant "pores". Assuming that pores can be represented by spheroids, we can relate the elastic properties to the pore structure using an effective medium theory. Moreover, the closure pressure of a thin crack-like pore is directly proportional to its aspect ratio. Hence, our first aim is to use the pressure dependence of seismic velocities to invert the aspect ratio distribution. We use a simple analytical algorithm developed by Zimmerman (Compressibility of Sandstones, 1991), which can be used for any effective medium theory. Previous works have used overly restrictive assumptions, such as assuming that the stiff pores are spherical, or that the interactions between pores can be neglected. Here, we assume that the rock contains an exponential distribution of crack aspect ratios, and one family of stiff pores having an aspect ratio lying somewhere between 0.01 and 1. We develop our model in two versions, using the Differential Scheme, and the Mori-Tanaka scheme. The inversion is done using data obtained in dry experiments, since pore fluids have a strong effect on velocities and tend to mask the effect of the pore geometry. This avoids complicated joint inversion of dry and wet data, such as done by Cheng and Toksoz (JGR, 1979). Our results show that for many sets of data on sandstones, we can fit very well the dry velocities. Our second aim is to predict the saturated velocities from our pore structure model, noting that at a given differential stress, the pore structure should be the same as for a dry test. Our results show that the Biot-Gassmann predictions always

  3. Subjective duration distortions mirror neural repetition suppression.

    Science.gov (United States)

    Pariyadath, Vani; Eagleman, David M

    2012-01-01

    Subjective duration is strongly influenced by repetition and novelty, such that an oddball stimulus in a stream of repeated stimuli appears to last longer in duration in comparison. We hypothesize that this duration illusion, called the temporal oddball effect, is a result of the difference in expectation between the oddball and the repeated stimuli. Specifically, we conjecture that the repeated stimuli contract in duration as a result of increased predictability; these duration contractions, we suggest, result from decreased neural response amplitude with repetition, known as repetition suppression. Participants viewed trials consisting of lines presented at a particular orientation (standard stimuli) followed by a line presented at a different orientation (oddball stimulus). We found that the size of the oddball effect correlates with the number of repetitions of the standard stimulus as well as the amount of deviance from the oddball stimulus; both of these results are consistent with a repetition suppression hypothesis. Further, we find that the temporal oddball effect is sensitive to experimental context--that is, the size of the oddball effect for a particular experimental trial is influenced by the range of duration distortions seen in preceding trials. Our data suggest that the repetition-related duration contractions causing the oddball effect are a result of neural repetition suppression. More generally, subjective duration may reflect the prediction error associated with a stimulus and, consequently, the efficiency of encoding that stimulus. Additionally, we emphasize that experimental context effects need to be taken into consideration when designing duration-related tasks.

  4. Incorporating Duration Information in Activity Recognition

    Science.gov (United States)

    Chaurasia, Priyanka; Scotney, Bryan; McClean, Sally; Zhang, Shuai; Nugent, Chris

    Activity recognition has become a key issue in smart home environments. The problem involves learning high level activities from low level sensor data. Activity recognition can depend on several variables; one such variable is duration of engagement with sensorised items or duration of intervals between sensor activations that can provide useful information about personal behaviour. In this paper a probabilistic learning algorithm is proposed that incorporates episode, time and duration information to determine inhabitant identity and the activity being undertaken from low level sensor data. Our results verify that incorporating duration information consistently improves the accuracy.

  5. Diagenesis and reservoir quality of Bhuban sandstones (Neogene), Titas Gas Field, Bengal Basin, Bangladesh

    Science.gov (United States)

    Aminul Islam, M.

    2009-06-01

    This study deals with the diagenesis and reservoir quality of sandstones of the Bhuban Formation located at the Titas Gas Field of Bengal Basin. Petrographic study including XRD, CL, SEM and BSE image analysis and quantitative determination of reservoir properties were carried out for this study. The sandstones are fine to medium-grained, moderately well to well sorted subfeldspathic arenites with subordinate feldspathic and lithic arenites. The diagenetic processes include clay infiltration, compaction and cementation (quartz overgrowth, chlorite, kaolinite, calcite and minor amount of pyrite, dolomite and K-feldspar overgrowth). Quartz is the dominant pore occluding cement and generally occurred as small euhedral crystals, locally as large pyramidal crystals in the primary pores. Pressure solution derived from grain contact is the main contributor of quartz overgrowths. Chlorite occurs as pore-lining and pore filling cement. In some cases, chlorite helps to retain porosity by preventing quartz overgrowth. In some restricted depth interval, pore-occlusion by calcite cement is very much intense. Kaolinite locally developed as vermiform and accelerated the minor porosity loss due to pore-occlusion. Kaolinite/chlorite enhances ineffective microporosity. Kaolinite is a by-product of feldspar leaching in the presence of acidic fluid produced during the maturation of organic matter in the adjacent Miocene or deeper Oligocene source rocks. The relation between diagenesis and reservoir quality is as follows: the initial porosity was decreased by compaction and cementation and then increased by leaching of the metastable grains and dissolution of cement. Good quality reservoir rocks were deposited in fluvial environment and hence quality of reservoir rocks is also environment selective. Porosity and permeability data exhibit good inverse correlation with cement. However, some data points indicate multiple controls on permeability. Reservoir quality is thus controlled by

  6. Rock Physics and Petrographic Parameters Relationship Within Siliciclastic Rocks: Quartz Sandstone Outcrop Study Case

    Science.gov (United States)

    Syafriyono, S.; Caesario, D.; Swastika, A.; Adlan, Q.; Syafri, I.; Abdurrokhim, A.; Mardiana, U.; Mohamad, F.; Alfadli, M. K.; Sari, V. M.

    2018-03-01

    Rock physical parameters value (Vp and Vs) is one of fundamental aspects in reservoir characterization as a tool to detect rock heterogenity. Its response is depend on several reservoir conditions such as lithology, pressure and reservoir fluids. The value of Vp and Vs is controlled by grain contact and contact stiffness, a function of clay mineral content and porosity also affected by mineral composition. The study about Vp and Vs response within sandstone and its relationship with petrographic parameters has become important to define anisotrophy of reservoir characteristics distribution and could give a better understanding about local diagenesis that influence clastic reservoir properties. Petrographic analysis and Vp-Vs calculation was carried out to 12 core sample which is obtained by hand-drilling of the outcrop in Sukabumi area, West Java as a part of Bayah Formation. Data processing and interpretation of sedimentary vertical succession showing that this outcrop comprises of 3 major sandstone layers indicating fluvial depositional environment. As stated before, there are 4 petrographic parameters (sorting, roundness, clay mineral content, and grain contact) which are responsible to the differences of shear wave and compressional wave value in this outcrop. Lithology with poor-sorted and well- roundness has Vp value lower than well-sorted and poor-roundness (sub-angular) grain. For the sample with high clay content, Vp value is ranging from 1681 to 2000 m/s and could be getting high until 2190 to 2714 m/s in low clay content sample even though the presence of clay minerals cannot be defined neither as matrix nor cement. The whole sample have suture grain contact indicating telogenesis regime whereas facies has no relationship with Vp and Vs value because of the different type of facies show similar petrographic parameters after diagenesis.

  7. Time-resolved tomography using acoustic emissions in the laboratory, and application to sandstone compaction

    Science.gov (United States)

    Brantut, Nicolas

    2018-02-01

    Acoustic emission and active ultrasonic wave velocity monitoring are often performed during laboratory rock deformation experiments, but are typically processed separately to yield homogenised wave velocity measurements and approximate source locations. Here I present a numerical method and its implementation in a free software to perform a joint inversion of acoustic emission locations together with the three-dimensional, anisotropic P-wave structure of laboratory samples. The data used are the P-wave first arrivals obtained from acoustic emissions and active ultrasonic measurements. The model parameters are the source locations and the P-wave velocity and anisotropy parameter (assuming transverse isotropy) at discrete points in the material. The forward problem is solved using the fast marching method, and the inverse problem is solved by the quasi-Newton method. The algorithms are implemented within an integrated free software package called FaATSO (Fast Marching Acoustic Emission Tomography using Standard Optimisation). The code is employed to study the formation of compaction bands in a porous sandstone. During deformation, a front of acoustic emissions progresses from one end of the sample, associated with the formation of a sequence of horizontal compaction bands. Behind the active front, only sparse acoustic emissions are observed, but the tomography reveals that the P-wave velocity has dropped by up to 15%, with an increase in anisotropy of up to 20%. Compaction bands in sandstones are therefore shown to produce sharp changes in seismic properties. This result highlights the potential of the methodology to image temporal variations of elastic properties in complex geomaterials, including the dramatic, localised changes associated with microcracking and damage generation.

  8. Time-resolved tomography using acoustic emissions in the laboratory, and application to sandstone compaction

    Science.gov (United States)

    Brantut, Nicolas

    2018-06-01

    Acoustic emission (AE) and active ultrasonic wave velocity monitoring are often performed during laboratory rock deformation experiments, but are typically processed separately to yield homogenized wave velocity measurements and approximate source locations. Here, I present a numerical method and its implementation in a free software to perform a joint inversion of AE locations together with the 3-D, anisotropic P-wave structure of laboratory samples. The data used are the P-wave first arrivals obtained from AEs and active ultrasonic measurements. The model parameters are the source locations and the P-wave velocity and anisotropy parameter (assuming transverse isotropy) at discrete points in the material. The forward problem is solved using the fast marching method, and the inverse problem is solved by the quasi-Newton method. The algorithms are implemented within an integrated free software package called FaATSO (Fast Marching Acoustic Emission Tomography using Standard Optimisation). The code is employed to study the formation of compaction bands in a porous sandstone. During deformation, a front of AEs progresses from one end of the sample, associated with the formation of a sequence of horizontal compaction bands. Behind the active front, only sparse AEs are observed, but the tomography reveals that the P-wave velocity has dropped by up to 15 per cent, with an increase in anisotropy of up to 20 per cent. Compaction bands in sandstones are therefore shown to produce sharp changes in seismic properties. This result highlights the potential of the methodology to image temporal variations of elastic properties in complex geomaterials, including the dramatic, localized changes associated with microcracking and damage generation.

  9. Depositional and diagenetic variability within the Cambrian Mount Simon Sandstone: Implications for carbon dioxide sequestration

    Science.gov (United States)

    Bowen, B.B.; Ochoa, R.I.; Wilkens, N.D.; Brophy, J.; Lovell, T.R.; Fischietto, N.; Medina, C.R.; Rupp, J.A.

    2011-01-01

    The Cambrian Mount Simon Sandstone is the major target reservoir for ongoing geologic carbon dioxide (CO2) sequestration demonstrations throughout the midwest United States. The potential CO2 reservoir capacity, reactivity, and ultimate fate of injected CO2 depend on textural and compositional properties determined by depositional and diagenetic histories that vary vertically and laterally across the formation. Effective and efficient prediction and use of the available pore space requires detailed knowledge of the depositional and diagenetic textures and mineralogy, how these variables control the petrophysical character of the reservoir, and how they vary spatially. Here, we summarize the reservoir characteristics of the Mount Simon Sandstone based on examination of geophysical logs, cores, cuttings, and analysis of more than 150 thin sections. These samples represent different parts of the formation and depth ranges of more than 9000 ft (>2743 m) across the Illinois Basin and surrounding areas. This work demonstrates that overall reservoir quality and, specifically, porosity do not exhibit a simple relationship with depth, but vary both laterally and with depth because of changes in the primary depositional facies, framework composition (i.e., feldspar concentration), and diverse diagenetic modifications. Diagenetic processes that have been significant in modifying the reservoir include formation of iron oxide grain coatings, chemical compaction, feldspar precipitation and dissolution, multiple generations of quartz overgrowth cementation, clay mineral precipitation, and iron oxide cementation. These variables provide important inputs for calculating CO2 capacity potential, modeling reactivity, and are also an important baseline for comparisons after CO2 injection. Copyright ??2011. The American Association of Petroleum Geologists/Division of Environmental Geosciences. All rights reserved.

  10. Palaeoclimatic trends deduced from the hydrochemistry of a Triassic sandstone aquifer, United Kingdom

    International Nuclear Information System (INIS)

    Bath, A.H.; Edmunds, W.M.; Andrews, J.N.

    1979-01-01

    A detailed geochemical study (elemental, isotopic and dissolved inert gases) of unconfined and confined sections of the Triassic non-marine sandstone aquifer in eastern England has been undertaken. Aspects of the recharge history of this aquifer over the past 40,000 years are revealed by examination of the data. 14 C activity and delta 13 C values show downgradient decrease and increase, respectively, the latter from -12 to -13 per mille (PDB) at outcrop to -8.5 per mille in deep confined groundwaters, indicating a continuing reaction between water and carbonate mineral phases. Although the bulk carbonate contained in sandstone samples gives delta 13 C around -7 per mille, modelling of the carbon isotopic evolution and consideration of the resulting 14 C age corrections suggest that a carbonate with delta 13 C closer to 0 per mille has played a major role in at least the earlier stages of hydrochemical evolution. The corrected radiocarbon age ranges, generated by the computer program WATEQF-ISOTOP, are used as a framework in which the palaeo-environmental information from oxygen and hydrogen isotope data, inert gas contents, and chloride levels are discussed. The measurement of dissolved helium levels demonstrates an excess of 4 He in many samples, which correlates with radiocarbon ages. The assumption of bulk chemical and physical properties for the aquifer rock allows independent 'excess 4 He' ages to be computed, which are mostly in excess of the corrected 14 C ages. The trend of delta 18 O is from about -8 per mille at outcrop to -9.7 per mille (SMOW) downgradient, which is significantly more depleted than has been found in previous studies of UK basins. The delta 2 H and delta 18 O values are related by the regression line delta 2 H=6.6delta 18 O+1; data from other UK studies also lie close to this trend

  11. Monitoring CO2 penetration and storage in the brine-saturated low permeable sandstone by the geophysical exploration technologies

    Science.gov (United States)

    Honda, H.; Mitani, Y.; Kitamura, K.; Ikemi, H.; Imasato, M.

    2017-12-01

    Carbon dioxide (CO2) capture and storage (CCS) plays a vital role in reducing greenhouse gas emissions. In the northern part of Kyushu region of Japan, complex geological structure (Coalfield) is existed near the CO2 emission source and has 1.06 Gt of CO2 storage capacity. The geological survey shows that these layers are formed by low permeable sandstone. It is necessary to monitor the CO2 behavior and clear the mechanisms of CO2 penetration and storage in the low permeable sandstone. In this study, measurements of complex electrical impedance (Z) and elastic wave velocity (P-wave velocity: Vp) were conducted during the supercritical CO2 injection experiment into the brine-saturated low permeable sandstone. The experiment conditions were as follows; Confining pressure: 20 MPa, Initial pore pressure: 10 MPa, 40 °, CO2 injection rate: 0.01 to 0.5 mL/min. Z was measured in the center of the specimen and Vp were measured at three different heights of the specimen at constant intervals. In addition, we measured the longitudinal and lateral strain at the center of the specimen, the pore pressure and CO2 injection volume (CO2 saturation). During the CO2 injection, the change of Z and Vp were confirmed. In the drainage terms, Vp decreased drastically once CO2 reached the measurement cross section.Vp showed the little change even if the flow rate increased (CO2 saturation increased). On the other hand, before the CO2 front reached, Z decreased with CO2-dissolved brine. After that, Z showed continuously increased as the CO2 saturation increased. From the multi-parameter (Hydraulic and Rock-physics parameters), we revealed the detail CO2 behavior in the specimen. In the brine-saturated low permeable sandstone, the slow penetration of CO2 was observed. However, once CO2 has passed, the penetration of CO2 became easy in even for brine-remainded low permeable sandstone. We conclude low permeable sandstone has not only structural storage capacity but also residual tapping

  12. Water-borne radon and hydrogeochemical based uranium exploration in Rajamundry sandstone, W. Godavari district, Andhra Pradesh

    International Nuclear Information System (INIS)

    Jeyagopal, A.V.; Rajaraman, H.S.; Som, Anjan

    2010-01-01

    The lithology and sedimentary structures of the Rajamundry Formation of the Mio-Pliocene age covering an area of 1100 sq.km. indicate that it may be a typical valley fill sediment. It is about 600 m thick comprising sandstone and clay with lignite as the main lithounits. It is continental in onshore and marine in the offshore and is in contact with Gondwana sediments and Rajamundry traps. Tertiary sandstones are important hosts for uranium mineralisation. The reducing gas (Methane or other volatile hydrocarbon) moving to uraniferous oxidising water has precipitated uranium in the sediments in South Texas and Northwest Colorado, USA: (a) along faults, (b) above petroliferous aquifers, (c) vertically above hydrocarbon accumulations and (d) oil-water interface at hydrocarbon accumulations i.e., at the points of introduction of reducent into oxidising ground waters. In this context, Rajamundry sandstone lying above the natural gas and petroleum bearing Krishna Godavari basin with faults is an important geological setting for uranium mineralisation. The exploration strategies of hydrogeochemical survey and water-borne Radon (Rn) surveys were selected in this soil-covered area. Hydrogeochemical survey carried out in the Rajamundry sandstone has brought out four hydro-uranium anomalous zones with water samples (10-45ppb) falling around Kadiyadda, Madhavaram, Erramalla and Chinna Malapalle areas of West Godavari district, Andhra Pradesh. The zones vary from 9 to 24 sq km area. Water-borne Radon was utilized as a tool for exploration of uranium in this soil covered terrain. Rn contours cluster around two zones around Kadiyadda and SW of Gollagudem wherein the Rn value is >60 counts/50 sec/500 ml. These Rn anomalies fall within the above mentioned hydrouranium anomalous zones. Gamma-ray logging of private bore wells has recorded relatively higher radioactivity in Kommugudem, which also falls in the high hydrouranium - high waterborne radon zone. These data and

  13. Characterization and 3D reservoir modelling of fluvial sandstones of the Williams Fork Formation, Rulison Field, Piceance Basin, Colorado, USA

    International Nuclear Information System (INIS)

    Pranter, Matthew J; Vargas, Marielis F; Davis, Thomas L

    2008-01-01

    This study describes the stratigraphic characteristics and distribution of fluvial deposits of the Upper Cretaceous Williams Fork Formation in a portion of Rulison Field and addresses 3D geologic modelling of reservoir sand bodies and their associated connectivity. Fluvial deposits include isolated and stacked point-bar deposits, crevasse splays and overbank (floodplain) mudrock. Within the Williams Fork Formation, the distribution and connectivity of fluvial sandstones significantly impact reservoir productivity and ultimate recovery. The reservoir sandstones are primarily fluvial point-bar deposits interbedded with shales and coals. Because of the lenticular geometry and limited lateral extent of the reservoir sandstones (common apparent widths of ∼500–1000 ft; ∼150–300 m), relatively high well densities (e.g. 10 acre (660 ft; 200 m) spacing) are often required to deplete the reservoir. Heterogeneity of these fluvial deposits includes larger scale stratigraphic variability associated with vertical stacking patterns and structural heterogeneities associated with faults that exhibit lateral and reverse offsets. The discontinuous character of the fluvial sandstones and lack of distinct marker beds in the middle and upper parts of the Williams Fork Formation make correlation between wells tenuous, even at a 10 acre well spacing. Some intervals of thicker and amalgamated sandstones within the middle and upper Williams Fork Formation can be correlated across greater distances. To aid correlation and for 3D reservoir modelling, vertical lithology proportion curves were used to estimate stratigraphic trends and define the stratigraphic zonation within the reservoir interval. Object-based and indicator-based modelling methods have been applied to the same data and results from the models were compared. Results from the 3D modelling indicate that sandstone connectivity increases with net-to-gross ratio and, at lower net-to-gross ratios (<30%), differences exist in

  14. Economic evaluation on tight sandstone gas development projects in China and recommendation on fiscal and taxation support policies

    Directory of Open Access Journals (Sweden)

    Zhen Yang

    2016-11-01

    Full Text Available China is rich in tight sandstone gas resources (“tight gas” for short. For example, the Sulige Gasfield in the Ordos Basin and the Upper Triassic Xujiahe Fm gas reservoir in the Sichuan Basin are typical tight gas reservoirs. In the past decade, tight gas reserve and production both have increased rapidly in China, but tight gas reservoirs are always managed as conventional gas reservoirs without effective fiscal, taxation and policy supports. The potential of sustainable tight gas production increase is obviously restricted. The tight gas development projects represented by the Sulige Gasfield have failed to make profit for a long period, and especially tight gas production has presented a slight decline since 2015. In this paper, a new economic evaluation method was proposed for tight gas development projects. The new method was designed to verify the key parameters (e.g. production decline rate and single-well economic service life depending on tight gas development and production characteristics, and perform the depreciation by using the production method. Furthermore, the possibility that the operation cost may rise due to pressure-boosting production and intermittent opening of gas wells is considered. The method was used for the tight gas development project of Sulige Gasfield, showing that its profit level is much lower than the enterprise's cost level of capital. In order to support a sustainable development of tight gas industry in China, it is recommended that relevant authorities issue value-added tax (VAT refund policy as soon as possible. It is necessary to restore the non-resident gas gate price of the provinces where tight gas is produced to the fair and reasonable level in addition to the fiscal subsidy of CNY0.24/m3, or offer the fiscal subsidy of CNY0.32/m3 directly based on the on-going gate price. With these support policies, tax income is expected to rise directly, fiscal expenditure will not increase, and gas

  15. An Experimental and Numerical Study on Cracking Behavior of Brittle Sandstone Containing Two Non-coplanar Fissures Under Uniaxial Compression

    Science.gov (United States)

    Yang, Sheng-Qi; Tian, Wen-Ling; Huang, Yan-Hua; Ranjith, P. G.; Ju, Yang

    2016-04-01

    To understand the fracture mechanism in all kinds of rock engineering, it is important to investigate the fracture evolution behavior of pre-fissured rock. In this research, we conducted uniaxial compression experiments to evaluate the influence of ligament angle on the strength, deformability, and fracture coalescence behavior of rectangular prismatic specimens (80 × 160 × 30 mm) of brittle sandstone containing two non-coplanar fissures. The experimental results show that the peak strength of sandstone containing two non-coplanar fissures depends on the ligament angle, but the elastic modulus is not closely related to the ligament angle. With the increase of ligament angle, the peak strength decreased at a ligament angle of 60°, before increasing up to our maximum ligament angle of 120°. Crack initiation, propagation, and coalescence were all observed and characterized from the inner and outer tips of pre-existing non-coplanar fissures using photographic monitoring. Based on the results, the sequence of crack evolution in sandstone containing two non-coplanar fissures was analyzed in detail. In order to fully understand the crack evolution mechanism of brittle sandstone, numerical simulations using PFC2D were performed for specimens containing two non-coplanar fissures under uniaxial compression. The results are in good agreement with the experimental results. By analyzing the stress field, the crack evolution mechanism in brittle sandstone containing two non-coplanar fissures under uniaxial compression is revealed. These experimental and numerical results are expected to improve the understanding of the unstable fracture mechanism of fissured rock engineering structures.

  16. Perspective and resource evaluation and metallogenic studies on sandstone-type uranium deposit in Qianjiadian depression of Songliao Basin

    Energy Technology Data Exchange (ETDEWEB)

    Yuliang, Xia; Jinrong, Lin; Ziying, Li; Shengxiang, Li; Hanbin, Liu; Zhiming, Wang; Guang, Fan [Beijing Research Inst. of Uranium Geology, Beijing (China); Jiwei, Zheng; Zhenji, Li; Mingyu, Zhang [Liaohe Oil Field, Panjin (China)

    2003-07-01

    The geotectonic evolution history of the southeastern part of Songliao Basin has been clearly described and it is pointed out that both of the provenance rocks and evolution features of the studied area are favorable to the formation of U-rich sandstone bodies, development of interlayered oxidation and providing uranium source for mineralization. Yaojia Formation in Qianjiadian depression has been found out to be the favorable target ore bed for looking for sandstone-type uranium deposit. On the basis of analysis of metallogenetic conditions, the perspective target area has been circled and a sandstone-type uranium deposit with a certain amounts of uranium tonnages has been discovered. The achievements and data have been gotten in the following aspects: constitution and features of ore-forming beds and sandstone bodies, uranium existence forms and mineralogical and chemical compositions of the ores, associated elements and their economic values for comprehensive mining. The study of metallogenetic features and mechanism of the uranium deposit suggested that pre-enrichment of uranium during the depositional-diagenetic stage provide a good basis for uranium mineralization, and hereafter interlayered oxidation as well as oil-gas reduction processes played a decisive role to uranium mineralization. U-Pb isotopic studies indicate that the ores have two isochron ages of 53{+-}3 Ma and 7.0{+-}0 Ma, corresponding to the periods of arid and semiarid paleo-climates which are favorable to interlayered oxidation development and uranium mineralization. It is concluded that the Qianjiadian sandstone-type uranium deposit is genetically related to interlayered oxidation and secondary reduction of oil-gas. The metallogenic model of Qianjiadian uranium deposit was set up. (authors)

  17. Interpreting Fracture Patterns in Sandstones Interbedded with Ductile Strata at the Salt Valley Anticline, Arches National Park, Utah; TOPICAL

    International Nuclear Information System (INIS)

    LORENZ, JOHN C.; COOPER, SCOTT P.

    2001-01-01

    Sandstones that overlie or that are interbedded with evaporitic or other ductile strata commonly contain numerous localized domains of fractures, each covering an area of a few square miles. Fractures within the Entrada Sandstone at the Salt Valley Anticline are associated with salt mobility within the underlying Paradox Formation. The fracture relationships observed at Salt Valley (along with examples from Paleozoic strata at the southern edge of the Holbrook basin in northeastern Arizona, and sandstones of the Frontier Formation along the western edge of the Green River basin in southwestern Wyoming), show that although each fracture domain may contain consistently oriented fractures, the orientations and patterns of the fractures vary considerably from domain to domain. Most of the fracture patterns in the brittle sandstones are related to local stresses created by subtle, irregular flexures resulting from mobility of the associated, interbedded ductile strata (halite or shale). Sequential episodes of evaporite dissolution and/or mobility in different directions can result in multiple, superimposed fracture sets in the associated sandstones. Multiple sets of superimposed fractures create reservoir-quality fracture interconnectivity within restricted localities of a formation. However, it is difficult to predict the orientations and characteristics of this type of fracturing in the subsurface. This is primarily because the orientations and characteristics of these fractures typically have little relationship to the regional tectonic stresses that might be used to predict fracture characteristics prior to drilling. Nevertheless, the high probability of numerous, intersecting fractures in such settings attests to the importance of determining fracture orientations in these types of fractured reservoirs

  18. Perspective and resource evaluation and metallogenic studies on sandstone-type uranium deposit in Qianjiadian depression of Songliao Basin

    International Nuclear Information System (INIS)

    Xia Yuliang; Lin Jinrong; Li Ziying; Li Shengxiang; Liu Hanbin; Wang Zhiming; Fan Guang; Zheng Jiwei; Li Zhenji; Zhang Mingyu

    2003-01-01

    The geotectonic evolution history of the southeastern part of Songliao Basin has been clearly described and it is pointed out that both of the provenance rocks and evolution features of the studied area are favorable to the formation of U-rich sandstone bodies, development of interlayered oxidation and providing uranium source for mineralization. Yaojia Formation in Qianjiadian depression has been found out to be the favorable target ore bed for looking for sandstone-type uranium deposit. On the basis of analysis of metallogenetic conditions, the perspective target area has been circled and a sandstone-type uranium deposit with a certain amounts of uranium tonnages has been discovered. The achievements and data have been gotten in the following aspects: constitution and features of ore-forming beds and sandstone bodies, uranium existence forms and mineralogical and chemical compositions of the ores, associated elements and their economic values for comprehensive mining. The study of metallogenetic features and mechanism of the uranium deposit suggested that pre-enrichment of uranium during the depositional-diagenetic stage provide a good basis for uranium mineralization, and hereafter interlayered oxidation as well as oil-gas reduction processes played a decisive role to uranium mineralization. U-Pb isotopic studies indicate that the ores have two isochron ages of 53±3 Ma and 7.0±0 Ma, corresponding to the periods of arid and semiarid paleo-climates which are favorable to interlayered oxidation development and uranium mineralization. It is concluded that the Qianjiadian sandstone-type uranium deposit is genetically related to interlayered oxidation and secondary reduction of oil-gas. The metallogenic model of Qianjiadian uranium deposit was set up. (authors)

  19. Digital Rock Physics Aplications: Visualisation Complex Pore and Porosity-Permeability Estimations of the Porous Sandstone Reservoir

    Science.gov (United States)

    Handoyo; Fatkhan; Del, Fourier

    2018-03-01

    Reservoir rock containing oil and gas generally has high porosity and permeability. High porosity is expected to accommodate hydrocarbon fluid in large quantities and high permeability is associated with the rock’s ability to let hydrocarbon fluid flow optimally. Porosity and permeability measurement of a rock sample is usually performed in the laboratory. We estimate the porosity and permeability of sandstones digitally by using digital images from μCT-Scan. Advantages of the method are non-destructive and can be applied for small rock pieces also easily to construct the model. The porosity values are calculated by comparing the digital image of the pore volume to the total volume of the sandstones; while the permeability values are calculated using the Lattice Boltzmann calculations utilizing the nature of the law of conservation of mass and conservation of momentum of a particle. To determine variations of the porosity and permeability, the main sandstone samples with a dimension of 300 × 300 × 300 pixels are made into eight sub-cubes with a size of 150 × 150 × 150 pixels. Results of digital image modeling fluid flow velocity are visualized as normal velocity (streamline). Variations in value sandstone porosity vary between 0.30 to 0.38 and permeability variations in the range of 4000 mD to 6200 mD. The results of calculations show that the sandstone sample in this research is highly porous and permeable. The method combined with rock physics can be powerful tools for determining rock properties from small rock fragments.

  20. Detrital zircon provenance of the Hartselle Sandstone Unit, Southeastern USA: Insights into sediment source, paleogeography, and setting

    Science.gov (United States)

    Harthy, M. A.; Gifford, J.

    2017-12-01

    The Hartselle sandstone is an excellent example of an Oil sand, a resource rich in bitumen. The unit is a light-colored thick-bedded to massive quartzose sandstone, that is widespread across an area from Georgia in the east to Mississippi in the west, and south from Alabama to Kentucky as a northern border. Formation thickness ranges from 0 to more than 150 feet. The unit has been stratigraphically dated to the Middle-Upper Mississippian age. One hypothesis suggests that the sandstone unit formed from the geological remains of barrier islands located in the ocean between Gondwana and Laurentia. The Hartselle is thought to have formed by the movement waves and currents along the shoreline, which carried sand and concentrated it into a set of northwest to southeast trending barrier islands. Transgression-regression events shifted the islands back and forth in relation to the position of the shoreline, leading to the large areal extent of the unit. However, the current data are not enough to explain the geographical position of the Hartselle sandstone unit as it is not running parallel to the ancient shoreline. Another mystery is the source of the sand, some believing the source was from the south (Gondwana) and others that erosion was from the north (Laurentia). Detrital zircon provenance analysis will address the uncertainty in sediment source. We will compare zircon U-Pb age spectra to possible Laurentian and Gondwanan source areas to discriminate between these possibilities. In addition, the age of the youngest detrital zircon population will provide additional constraints on the maximum age of deposition for the unit. These detrital ages will also help us to understand the tectonic setting at the time of Hartselle deposition. Lastly, we aim to explain the widespread nature of the unit and the processes involved in the formation of the Hartselle sandstone. When taken together, these interpretations will illuminate the age, depositional and tectonic setting of a

  1. Initial assessment of the infiltration and overland flow for different rainfall events in land constituted of sandstones of the Botucatu Formation (Guarani Aquifer), State of São Paulo, Brazil

    Science.gov (United States)

    Zuquette, Lázaro Valentin; Palma, Janaina Barrios; Pejon, Osni José

    2006-06-01

    This study was carried out in the Córrego do Vaçununga basin constituted of eolic sandstones of Botucatu Formation and residual unconsolidated materials (>90%), considered the most important unconfined aquifer in Brazil, in the city of Luiz Antonio, State of São Paulo, Brazil. Laboratory and in situ tests were performed to characterize the unconsolidated materials in terms of basic physical properties, potential infiltration rate, suction and hydraulic conductivity. The results for infiltration and overland flow depths were obtained according to Morel-Seytoux and Khanji (Water Resour Res 10(4):795-800, 1976) and Chu (Water Resour Res 14(3):461-466, 1978) adaptation of the Green and Ampt [J Agr Sci 4(Part 1):1-24, 1911] model for steady and transient rainfalls, respectively. Rainfall data were collected from January of 2000 to December of 2002, and 12 scenarios were defined considering the intensity and durations. Rather than high homogeneity in terms of the texture of unconsolidated materials, the infiltration and overland flow ratio depends on the type of land use and associated management practices. The results showed that rainfall with high intensity and short duration do not produce high overland flow ratio as we have observed for transient scenarios with long duration and low intensities.

  2. Excessive daytime sleepiness, nocturnal sleep duration and ...

    African Journals Online (AJOL)

    Background and objectives. Short nocturnal sleep duration resulting in sleep debt may be a cause of excessive daytime sleepiness (EDS). Severity of depression (psychopathology) has been found to be directly related to EDS. There is an association between sleep duration and mental health, so there may therefore be an ...

  3. Unemployment Duration over the Business Cycle

    DEFF Research Database (Denmark)

    Rosholm, Michael

    1996-01-01

    In this paper I study the way in which individual unemployment durations vary over the business cycle, as measured by the aggregate unemployment rate. I decompose the cyclical variations in observed unemployment durations into a composition al and a general part. The compositional part consists...

  4. Word Durations in Non-Native English

    Science.gov (United States)

    Baker, Rachel E.; Baese-Berk, Melissa; Bonnasse-Gahot, Laurent; Kim, Midam; Van Engen, Kristin J.; Bradlow, Ann R.

    2010-01-01

    In this study, we compare the effects of English lexical features on word duration for native and non-native English speakers and for non-native speakers with different L1s and a range of L2 experience. We also examine whether non-native word durations lead to judgments of a stronger foreign accent. We measured word durations in English paragraphs read by 12 American English (AE), 20 Korean, and 20 Chinese speakers. We also had AE listeners rate the `accentedness' of these non-native speakers. AE speech had shorter durations, greater within-speaker word duration variance, greater reduction of function words, and less between-speaker variance than non-native speech. However, both AE and non-native speakers showed sensitivity to lexical predictability by reducing second mentions and high frequency words. Non-native speakers with more native-like word durations, greater within-speaker word duration variance, and greater function word reduction were perceived as less accented. Overall, these findings identify word duration as an important and complex feature of foreign-accented English. PMID:21516172

  5. On the Limitation of Warranty Duration.

    OpenAIRE

    Emons, Winand

    1989-01-01

    This paper analyzes the frequently-observed phenomenon that firms offer product warranties that are of much shorter duration than the life expectancy of these products. It is shown that competitive equilibria may entail limitation of warranty duration if firms face adverse selection problems with respect to different consumers. Copyright 1989 by Blackwell Publishing Ltd.

  6. From Sleep Duration to Childhood Obesity

    DEFF Research Database (Denmark)

    Börnhorst, Claudia; Hense, Sabrina; Ahrens, Wolfgang

    2012-01-01

    Sleep duration has been identified as risk factor for obesity already in children. Besides investigating the role of fat mass (FM), this study addressed the question whether endocrine mechanisms act as intermediates in the association between sleep duration and overweight/obesity. Within...... the framework of the IDEFICS study, the present research was conducted in 609 German resident children aged 2–9 years with information on fasting insulin, C-reactive protein and cortisol levels next to anthropometric measurements and parental questionnaires. Emphasising methodological aspects, an age......-specific measure of sleep duration was derived to account for alteration in sleep duration during childhood/period of growth. Multivariate linear regression and quantile regression models confirmed an inverse relationship between sleep duration and measures of overweight/obesity. The estimate for the association...

  7. Developing Project Duration Models in Software Engineering

    Institute of Scientific and Technical Information of China (English)

    Pierre Bourque; Serge Oligny; Alain Abran; Bertrand Fournier

    2007-01-01

    Based on the empirical analysis of data contained in the International Software Benchmarking Standards Group(ISBSG) repository, this paper presents software engineering project duration models based on project effort. Duration models are built for the entire dataset and for subsets of projects developed for personal computer, mid-range and mainframeplatforms. Duration models are also constructed for projects requiring fewer than 400 person-hours of effort and for projectsre quiring more than 400 person-hours of effort. The usefulness of adding the maximum number of assigned resources as asecond independent variable to explain duration is also analyzed. The opportunity to build duration models directly fromproject functional size in function points is investigated as well.

  8. Research on geochronology and uranium source of sandstone-hosted uranium ore-formation in major uranium-productive basins, Northern-China

    International Nuclear Information System (INIS)

    Xia Yuliang; Liu Hanbin; Lin Jinrong; Fan Guang; Hou Yanxian

    2004-12-01

    A method is developed for correcting uranium content in uranium ore samples by considering the U-Ra equilibrium coefficient, then a U-Pb isochron is drawn up. By performing the above correction ore-formation ages of sandstone-hosted uranium mineralization which may be more realistic have been obtained. The comparative research on U-Pb isotopic ages of detritic zircon in ore-hosting sandstone and zircon in intermediate-acid igneous rocks in corresponding provenance area indicates that the ore-hosting sandstone is originated from the erosion of intermediate-acid igneous rocks and the latters are the material basis for the formation of the uranium-rich sandstone beds. On the basis of the study on U-Pb isotopic system evolution of the provenance rocks and sandstones from ore-hosting series, it is verified that the uranium sources of the sandstone-hosted uranium deposit are: the intermediate-acid igneous rocks with high content of mobile uranium, and the sandstone bodies pre-concentrated uranium. (authors)

  9. Nivelstein sandstone, weakly lithified pure silica sands from the Dutch-German border area, intermittently used in architecture for two millennia

    Science.gov (United States)

    Nijland, Timo G.; Wim Dubelaar, C.

    2017-04-01

    The current paper provides a concise overview of the geological setting of the Nivelstein sandstone in broad sense, its petrographic and physical characteristics, and its use as natural stone. Miocene pure silica sands occur around Heerlen in the southeastern part of the Dutch province of Limburg and Herzogenrath in adjacent Germany, as well as in the Belgian province of Limburg near Opgrimbie. In Dutch Limburg and in Germany are three large active exploitations, quarrying the sands for industrial purposes. On top of the unconsolidated sands in the Herzogenrath quarry, lithified banks of sandstone occur, known as Nivelstein (or more rarely Herzogenrath) sandstone. This sandstone has been used as dimension stone and ornamental stone since Roman times. In the 11th century the quarry was reopened and after a long period of disuse sandstone blocks were again quarried in the second half of the 19th century. The lithification of the Nivelstein sandstone usually is very weak, with grain to grain contacts and some newly formed quartz rims only. The clay content is extremely low and is restricted to tiny booklets of kaolinite. Despite the weak cementation the Nivelstein sandstone has proved to be very time-resistant building stone that forms a major element in the stone cultural heritage of the Dutch- German border area.

  10. Uranium-series disequilibria as a means to study recent migration of uranium in a sandstone-hosted uranium deposit, NW China

    International Nuclear Information System (INIS)

    Min Maozhong; Peng Xinjian; Wang Jinping; Osmond, J.K.

    2005-01-01

    Uranium concentration and alpha specific activities of uranium decay series nuclides 234 U, 238 U, 230 Th, 232 Th and 226 Ra were measured for 16 oxidized host sandstone samples, 36 oxic-anoxic (mineralized) sandstone samples and three unaltered primary sandstone samples collected from the Shihongtan deposit. The results show that most of the ores and host sandstones have close to secular equilibrium alpha activity ratios for 234 U/ 238 U, 230 Th/ 238 U, 230 Th/ 234 U and 226 Ra/ 230 Th, indicating that intensive groundwater-rock/ore interaction and uranium migration have not taken place in the deposit during the last 1.0 Ma. However, some of the old uranium ore bodies have locally undergone leaching in the oxidizing environment during the past 300 ka to 1.0 Ma or to the present, and a number of new U ore bodies have grown in the oxic-anoxic transition (mineralized) subzone during the past 1.0 Ma. Locally, uranium leaching has taken place during the past 300 ka to 1.0 Ma, and perhaps is still going on now in some sandstones of the oxidizing subzone. However, uranium accumulation has locally occurred in some sandstones of the oxidizing environment during the past 1 ka to 1.0 Ma, which may be attributed to adsorption of U(VI) by clays contained in oxidized sandstones. A recent accumulation of uranium has locally taken place within the unaltered sandstones of the primary subzone close to the oxic-anoxic transition environment during the past 300 ka to 1.0 Ma. Results from the present study also indicate that uranium-series disequilibrium is an important tool to trace recent migration of uranium occurring in sandstone-hosted U deposits during the past 1.0 Ma and to distinguish the oxidation-reduction boundary

  11. Transport upscaling from pore- to Darcy-scale: Incorporating pore-scale Berea sandstone Lagrangian velocity statistics into a Darcy-scale transport CTRW model

    Science.gov (United States)

    Puyguiraud, Alexandre; Dentz, Marco; Gouze, Philippe

    2017-04-01

    For the past several years a lot of attention has been given to pore-scale flow in order to understand and model transport, mixing and reaction in porous media. Nevertheless we believe that an accurate study of spatial and temporal evolution of velocities could bring important additional information for the upscaling from pore to higher scales. To gather these pieces of information, we perform Stokes flow simulations on pore-scale digitized images of a Berea sandstone core. First, micro-tomography (XRMT) imaging and segmentation processes allow us to obtain 3D black and white images of the sample [1]. Then we used an OpenFoam solver to perform the Stokes flow simulations mentioned above, which gives us the velocities at the interfaces of a cubic mesh. Subsequently, we use a particle streamline reconstruction technique which uses the Eulerian velocity field previously obtained. This technique, based on a modified Pollock algorithm [2], enables us to make particle tracking simulations on the digitized sample. In order to build a stochastic pore-scale transport model, we analyze the Lagrangian velocity series in two different ways. First we investigate the velocity evolution by sampling isochronically (t-Lagrangian), and by studying its statistical properties in terms of one- and two-points statistics. Intermittent patterns can be observed. These are due to the persistance of low velocities over a characteristic space length. Other results are investigated, such as correlation functions and velocity PDFs, which permit us to study more deeply this persistence in the velocities and to compute the correlation times. However, with the second approach, doing these same analysis in space by computing the velocities equidistantly, enables us to remove the intermittency shown in the temporal evolution and to model these velocity series as a Markov process. This renders the stochastic particle dynamics into a CTRW [3]. [1] Gjetvaj, F., A. Russian, P. Gouze, and M. Dentz (2015

  12. Opening keynote

    International Nuclear Information System (INIS)

    Rae, B.

    1997-01-01

    In his opening address, the former premier of Ontario summarized the background of the Macdonald Committee which was appointed by his government after it became increasingly apparent that the infrastructure of Hydro Ontario was far bigger than the province and the economy could afford, and that the service that had once given Ontario tremendous competitive advantage, in the form of relatively cheap electric power, had become unsustainable in an era of economic downturn and zero inflation. He stated that the debate about Hydro is part of a broader issue, and it is no longer possible to manage our electricity system as if we were a self-enclosed universe. He predicted that the North American electricity grid will become increasingly interdependent, and that Hydro will have to develop competitive price structures, both to hold its domestic market share and to compete for export sales. He outlined the most pressing issues for Hydro as being debt reduction, while pursuing internal changes to make the organization more efficient. Organizational changes such as the creation of Ontario Hydro International, Ontario Hydro Research, separation of generation operations from the grid, and establishment of separate price and efficiency targets for the autonomous organizations within the utility family, were moves in the right direction. Equally important is to make sure that however Hydro might develop in the future, it is going to be fair to customers, and that the billions of dollars invested in Hydro by Ontario taxpayers over the years, are safeguarded

  13. Openness initiative

    International Nuclear Information System (INIS)

    Duncan, S.S.

    1995-01-01

    Although antinuclear campaigns seem to be effective, public communication and education efforts on low-level radioactive waste have mixed results. Attempts at public information programs on low-level radioactive waste still focus on influencing public opinion. A question then is: open-quotes Is it preferable to have a program focus on public education that will empower individuals to make informed decisions rather than trying to influence them in their decisions?close quotes To address this question, a case study with both quantitative and qualitative data will be used. The Ohio Low-Level Radioactive Waste Education Program has a goal to provide people with information they want/need to make their own decisions. The program initiated its efforts by conducting a statewide survey to determine information needed by people and where they turned for that information. This presentation reports data from the survey and then explores the program development process in which programs were designed and presented using the information. Pre and post data from the programs reveal attitude and knowledge shifts

  14. Openness initiative

    Energy Technology Data Exchange (ETDEWEB)

    Duncan, S.S. [Los Alamos National Lab., NM (United States)

    1995-12-31

    Although antinuclear campaigns seem to be effective, public communication and education efforts on low-level radioactive waste have mixed results. Attempts at public information programs on low-level radioactive waste still focus on influencing public opinion. A question then is: {open_quotes}Is it preferable to have a program focus on public education that will empower individuals to make informed decisions rather than trying to influence them in their decisions?{close_quotes} To address this question, a case study with both quantitative and qualitative data will be used. The Ohio Low-Level Radioactive Waste Education Program has a goal to provide people with information they want/need to make their own decisions. The program initiated its efforts by conducting a statewide survey to determine information needed by people and where they turned for that information. This presentation reports data from the survey and then explores the program development process in which programs were designed and presented using the information. Pre and post data from the programs reveal attitude and knowledge shifts.

  15. Subjective duration distortions mirror neural repetition suppression.

    Directory of Open Access Journals (Sweden)

    Vani Pariyadath

    Full Text Available Subjective duration is strongly influenced by repetition and novelty, such that an oddball stimulus in a stream of repeated stimuli appears to last longer in duration in comparison. We hypothesize that this duration illusion, called the temporal oddball effect, is a result of the difference in expectation between the oddball and the repeated stimuli. Specifically, we conjecture that the repeated stimuli contract in duration as a result of increased predictability; these duration contractions, we suggest, result from decreased neural response amplitude with repetition, known as repetition suppression.Participants viewed trials consisting of lines presented at a particular orientation (standard stimuli followed by a line presented at a different orientation (oddball stimulus. We found that the size of the oddball effect correlates with the number of repetitions of the standard stimulus as well as the amount of deviance from the oddball stimulus; both of these results are consistent with a repetition suppression hypothesis. Further, we find that the temporal oddball effect is sensitive to experimental context--that is, the size of the oddball effect for a particular experimental trial is influenced by the range of duration distortions seen in preceding trials.Our data suggest that the repetition-related duration contractions causing the oddball effect are a result of neural repetition suppression. More generally, subjective duration may reflect the prediction error associated with a stimulus and, consequently, the efficiency of encoding that stimulus. Additionally, we emphasize that experimental context effects need to be taken into consideration when designing duration-related tasks.

  16. Petroacoustic Modelling of Heterolithic Sandstone Reservoirs: A Novel Approach to Gassmann Modelling Incorporating Sedimentological Constraints and NMR Porosity data

    Science.gov (United States)

    Matthews, S.; Lovell, M.; Davies, S. J.; Pritchard, T.; Sirju, C.; Abdelkarim, A.

    2012-12-01

    Heterolithic or 'shaly' sandstone reservoirs constitute a significant proportion of hydrocarbon resources. Petroacoustic models (a combination of petrophysics and rock physics) enhance the ability to extract reservoir properties from seismic data, providing a connection between seismic and fine-scale rock properties. By incorporating sedimentological observations these models can be better constrained and improved. Petroacoustic modelling is complicated by the unpredictable effects of clay minerals and clay-sized particles on geophysical properties. Such effects are responsible for erroneous results when models developed for "clean" reservoirs - such as Gassmann's equation (Gassmann, 1951) - are applied to heterolithic sandstone reservoirs. Gassmann's equation is arguably the most popular petroacoustic modelling technique in the hydrocarbon industry and is used to model elastic effects of changing reservoir fluid saturations. Successful implementation of Gassmann's equation requires well-constrained drained rock frame properties, which in heterolithic sandstones are heavily influenced by reservoir sedimentology, particularly clay distribution. The prevalent approach to categorising clay distribution is based on the Thomas - Stieber model (Thomas & Stieber, 1975), this approach is inconsistent with current understanding of 'shaly sand' sedimentology and omits properties such as sorting and grain size. The novel approach presented here demonstrates that characterising reservoir sedimentology constitutes an important modelling phase. As well as incorporating sedimentological constraints, this novel approach also aims to improve drained frame moduli estimates through more careful consideration of Gassmann's model assumptions and limitations. A key assumption of Gassmann's equation is a pore space in total communication with movable fluids. This assumption is often violated by conventional applications in heterolithic sandstone reservoirs where effective porosity, which

  17. Changes in the composition and properties of Ashalchinskoye bitumen-saturated sandstones when exposed to water vapor

    Science.gov (United States)

    Korolev, E.; Eskin, A.; Kolchugin, A.; Morozov, V.; Khramchenkov, M.; Gabdelvalieva, R.

    2018-05-01

    Ashalchinskoye bitumen deposit is an experimental platform for testing technology of high-viscosity oil extraction from reservoir rocks. Last time for enhanced of oil recovery in reservoir used pressurization a water vapor with a temperature of ∼ 180 ° C (SAGD technology). However, what happens in sandstone reservoir is little known. We did a study of the effects of water vapor on the structural components of bitumen saturated sandstone. In paper were studied the rock samples at base condition and after one week exposure by water vapour. The thermal analysis showed that steaming helps to removes light and middle oil fractions with a boiling point up to 360 ° C from oil saturated sandstones. Content of heavy oil fractions virtually unchanged. Studying the composition of water extractions of samples showed that the process of aquathermolysis of oil is accompanied by a lowering of the pH of the pore solution from 7.4 to 6.5 and rise content in several times of mobile cations Ca2+, Mg2+ and HCO3 -, SO4 2- anions. Follows from this that the thermal steam effect by bitumen saturated sandstones leads to partial oxidation of hydrocarbons with to form a carbon dioxide. The source of sulfate ions were oxidized pyrite aggregates. Due to the increasing acidity of condensed water, which fills the pore space of samples, pore fluid becomes aggressive to calcite and dolomite cement of bitumen saturated sandstones. As a result of the dissolution of carbonate cement the pore fluid enriched by calcium and magnesium cations. Clearly, that the process is accompanied by reduction of contact strength between fragments of minerals and rocks. Resulting part of compounds is separated from the outer side of samples and falls to bottom of water vapor container. Decreasing the amount of calcite and dolomite anions in samples in a steam-treated influence is confirmed by X-Ray analysis. X-Ray analysis data of study adscititious component of rocks showed that when influenced of water vapor to

  18. Micro-Ct Imaging of Multi-Phase Flow in Carbonates and Sandstones

    Science.gov (United States)

    Andrew, M. G.; Bijeljic, B.; Blunt, M. J.

    2013-12-01

    One of the most important mechanisms that limits the escape of CO2 when injected into the subsurface for the purposes of carbon storage is capillary trapping, where CO2 is stranded as pore-scale droplets (ganglia). Prospective storage sites are aquifers or reservoirs that tend to be at conditions where CO2 will reside as a super-critical phase. In order to fully describe physical mechanisms characterising multi-phase flow during and post CO2 injection, experiments need to be conducted at these elevated aquifer/reservoir conditions - this poses a considerable experimental challenge. A novel experimental apparatus has been developed which uses μCT scanning for the non-invasive imaging of the distribution of CO2 in the pore space of rock with resolutions of 7μm at temperatures and pressures representative of the conditions present in prospective saline aquifer CO2 storage sites. The fluids are kept in chemical equilibrium with one-another and with the rock into which they are injected. This is done to prevent the dissolution of the CO2 in the brine to form carbonic acid, which can then react with the rock, particularly carbonates. By eliminating reaction we study the fundamental mechanisms of capillary trapping for an unchanging pore structure. In this study we present a suite of results from three carbonate and two sandstone rock types, showing that, for both cases the CO2 acts as the non-wetting phase and significant quantities of CO2 is trapped. The carbonate examined represent a wide variety of pore topologies with one rock with a very well connected, high porosity pore space (Mt Gambier), one with a lower porosity, poorly connected pore space (Estaillades) and one with a cemented bead pack type pore space (Ketton). Both sandstones (Doddington and Bentheimer) were high permeability granular quartzites. CO2 was injected into each rock, followed by brine injection. After brine injection the entire length of the rock core was scanned, processed and segmented into

  19. Duration of therapy – Does it matter?

    DEFF Research Database (Denmark)

    Kramer Schmidt, Lotte; Bojesen, Anders Bo; Nielsen, Anette Søgaard

    2018-01-01

    Background The recommendations in clinical guidelines for duration of therapy for alcohol use disorder (AUD) are based on consensus decisions. In reality, we do not know the optimal duration of an alcohol treatment course. Methods A systematic review and meta-regression of randomized controlled...... project in itself may influence outcome in studies of psychosocial treatment for alcohol use disorder....... across studies. Treatment outcome was defined as long-term alcohol use measured in percentage of days abstinent (PDA), percentage of heavy days drinking (PHD), and/or proportion of participants abstinent (ABS). Results 48 studies encompassing 8984 participants. Mean planned duration of therapy: 18 (8...

  20. Geological and petrophysical characterization of the Ferron Sandstone for 3-D simulation of a fluvial-deltaic reservoir. Deliverable 2.5.4, Ferron Sandstone lithologic strip logs, Emergy & Sevier Counties, Utah: Volume I

    Energy Technology Data Exchange (ETDEWEB)

    Allison, M.L.

    1995-12-08

    Strip logs for 491 wells were produced from a digital subsurface database of lithologic descriptions of the Ferron Sandstone Member of the Mancos Shale. This subsurface database covers wells from the parts of Emery and Sevier Counties in central Utah that occur between Ferron Creek on the north and Last Chance Creek on the south. The lithologic descriptions were imported into a logging software application designed for the display of stratigraphic data. Strip logs were produced at a scale of one inch equals 20 feet. The strip logs were created as part of a study by the Utah Geological Survey to develop a comprehensive, interdisciplinary, and qualitative characterization of a fluvial-deltaic reservoir using the Ferron Sandstone as a surface analogue. The study was funded by the U.S. Department of Energy (DOE) under the Geoscience/Engineering Reservoir Characterization Program.

  1. Tester Detects Steady-Short Or Intermittent-Open Circuits

    Science.gov (United States)

    Anderson, Bobby L.

    1990-01-01

    Momentary open circuits or steady short circuits trigger buzzer. Simple, portable, lightweight testing circuit sounds long-duration alarm when it detects steady short circuit or momentary open circuit in coaxial cable or other two-conductor transmission line. Tester sensitive to discontinuities lasting 10 microseconds or longer. Used extensively for detecting intermittent open shorts in accelerometer and extensometer cables. Also used as ordinary buzzer-type continuity checker to detect steady short or open circuits.

  2. Mechanical Weakening during Fluid Injection in Critically Stressed Sandstones with Acoustic Monitoring

    Science.gov (United States)

    David, C.; Dautriat, J. D.; Sarout, J.; Macault, R.; Bertauld, D.

    2014-12-01

    Water weakening is a well-known phenomenon which can lead to subsidence during the production of hydrocarbon reservoirs. The example of the Ekofisk oil field in the North Sea has been well documented for years. In order to assess water weakening effects in reservoir rocks, previous studies have focused on changes in the failure envelopes derived from mechanical tests conducted on rocks saturated either with water or with inert fluids. However, little attention has been paid so far on the mechanical behaviour during the fluid injection stage, like in enhanced oil recovery operations. We studied the effect of fluid injection on the mechanical behaviour of Sherwood sandstone, a weakly-consolidated sandstone sampled at Ladram Bay in UK. In order to highlight possible weakening effects, water and inert oil have been injected into critically-loaded samples to assess their effect on strength and elastic properties and to derive the acoustic signature of the saturation front for each fluid. The specimens were instrumented with 16 ultrasonic P-wave transducers for both passive and active acoustic monitoring during fluid injection and loading. After conducting standard triaxial tests on three samples saturated with air, water and oil respectively, mechanical creep tests were conducted on dry samples loaded at 80% of the compressive strength of the dry rock. While these conditions are kept constant, a fluid is injected at the bottom end of the sample with a low back pressure (0.5 MPa) to minimize effective stress variations during injection. Both water and oil were used as the injected pore fluid in two experiments. As soon as the fluids start to flow into the samples, creep is taking place with a much higher strain rate for water injection compared to oil injection. A transition from secondary creep to tertiary creep is observed in the water injection test whereas in the oil injection test no significant creep acceleration is observed after one pore volume of oil was

  3. Net-infiltration map of the Navajo Sandstone outcrop area in western Washington County, Utah

    Science.gov (United States)

    Heilweil, Victor M.; McKinney, Tim S.

    2007-01-01

    As populations grow in the arid southwestern United States and desert bedrock aquifers are increasingly targeted for future development, understanding and quantifying the spatial variability of net infiltration and recharge becomes critically important for inventorying groundwater resources and mapping contamination vulnerability. A Geographic Information System (GIS)-based model utilizing readily available soils, topographic, precipitation, and outcrop data has been developed for predicting net infiltration to exposed and soil-covered areas of the Navajo Sandstone outcrop of southwestern Utah. The Navajo Sandstone is an important regional bedrock aquifer. The GIS model determines the net-infiltration percentage of precipitation by using an empirical equation. This relation is derived from least squares linear regression between three surficial parameters (soil coarseness, topographic slope, and downgradient distance from outcrop) and the percentage of estimated net infiltration based on environmental tracer data from excavations and boreholes at Sand Hollow Reservoir in the southeastern part of the study area.Processed GIS raster layers are applied as parameters in the empirical equation for determining net infiltration for soil-covered areas as a percentage of precipitation. This net-infiltration percentage is multiplied by average annual Parameter-elevation Regressions on Independent Slopes Model (PRISM) precipitation data to obtain an infiltration rate for each model cell. Additionally, net infiltration on exposed outcrop areas is set to 10 percent of precipitation on the basis of borehole net-infiltration estimates. Soils and outcrop net-infiltration rates are merged to form a final map.Areas of low, medium, and high potential for ground-water recharge have been identified, and estimates of net infiltration range from 0.1 to 66 millimeters per year (mm/yr). Estimated net-infiltration rates of less than 10 mm/yr are considered low, rates of 10 to 50 mm/yr are

  4. CO2-induced mechanical behaviour of Hawkesbury sandstone in the Gosford basin: An experimental study

    International Nuclear Information System (INIS)

    Rathnaweera, T.D.; Ranjith, P.G.; Perera, M.S.A.; Haque, A.; Lashin, A.; Al Arifi, N.; Chandrasekharam, D; Yang, SQ; Xu, T; Wang, SH; Yasar, E

    2015-01-01

    Carbon dioxide (CO 2 ) sequestered in saline aquifers undergoes a variety of chemically-coupled mechanical effects, which may cause CO 2 -induced mechanical changes and time-dependent reservoir deformation. This paper investigates the mineralogical and microstructural changes that occur in reservoir rocks following injection of CO 2 in deep saline aquifers and the manner in which these changes influence the mechanical properties of the reservoir rocks. In this study, cylindrical sandstone specimens, 38 mm in diameter and 76 mm high, obtained from the Gosford basin, were used to perform a series of unconfined compressive strength (UCS) tests. Different saturation conditions: dry, water- and brine-saturated sandstone samples with and without scCO 2 (super-critical carbon dioxide) injection, were considered in the study to obtain a comprehensive understanding of the impact of scCO 2 injection during the CO 2 sequestration process on saline aquifer mechanical properties. An acoustic emission (AE) system was employed to identify the stress threshold values of crack closure, crack initiation and crack damage for each testing condition during the whole deformation process of the specimens. Finally, scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray fluorescence (XRF) analyses were performed to evaluate the chemical and mineralogical changes that occur in reservoir rocks during CO 2 injection. From the test results, it is clear that the CO 2 -saturated samples possessed a lower peak strength compared to non-CO 2 saturated samples. According to SEM, XRD and XRF analyses, considerable quartz mineral corrosion and dissolution of calcite and siderite were observed during the interactions of the CO 2 /water/rock and CO 2 /brine/rock systems, which implies that mineralogical and geochemical rock alterations affect rock mechanical properties by accelerating the collapse mechanisms of the pore matrix. AE results also reveal the weakening effect of rock pore

  5. Architectural evidence of dune collapse in the Navajo Sandstone, Zion National Park, Utah

    Science.gov (United States)

    Ford, Colby; Bryant, Gerald; Nick, Kevin E.

    2016-10-01

    The Canyon Overlook Trail of Zion National Park follows an outcrop of Navajo Sandstone, which displays a uniquely well-exposed assemblage of features associated with failure of the lee face of a large eolian dune, and run-out over an expanse of interdune sediments downwind of that bedform. Exposed features include dramatic folds in the interdune succession and a stacked series of thrust sheets incorporating both interdune and overlying dune deposits. Thrust surfaces display consistent strikes, parallel to those of undeformed foresets, and incorporate zones of brittle failure and fluid deformation, including folds overturned in the direction of foreset dip. These features correspond to predictions made by a previous researcher's model of dune collapse, formulated from less fortuitously exposed architectures in the Navajo Sandstone. Unlike the previous model, however, this site preserves distinct indications that the bulk of deformed material accumulated above the level of the contemporary interdune surface, in an aggradational succession. Paleotopographic reconstruction, based on preserved facies relationships at this site, indicates the presence of a large dune, partially encroached upon a well-developed wet interdune succession, made up of two half-meter carbonate mud layers, separated by a meter of medium-grained sand. Trapping of pore water pressure between these mud layers during liquefaction reduced shear strength in this interval, facilitating the collapse of the lee face of the upwind dune into the interdune area, and transmitted resultant shear forces to distal portions of the interdune expanse, in the shallow subsurface. Shear failure developed along bedding planes in the horizontally laminated carbonate muds, which provided both lubrication of the shear surfaces and structural support for the preservation of coherent thrust sheets during production of an imbricated succession of shear zones in the toe portion of the slump. Individual shear surfaces

  6. Petrophysical characterization of three commercial varieties of miocene sandstones from the Ebro valley

    Directory of Open Access Journals (Sweden)

    Gisbert, J.

    2007-08-01

    Full Text Available Miocene sandstones studied were used extensively to build Aragon’s architectural heritage, are still used in modern construction. The quarries presently located on the edge of the Ebro Valley depression. The present paper describes an exhaustive petrophysical study of these materials, which while, of the same age and from the same deposition basin, exhibit different mineralogical and textural characteristics and as a result, different physical and mechanical properties and durability. The petrographic and petrophysical characteristics of these materials were evaluated with tests prescribed in UNE (Spanish, NORMAL and ASTM standards. All the results were subjected to statistical analysis to identify possible textural and compositional nonuniformities in the material that may underlie behavioural changes. The results of the present paper show that their petrophysical characteristics afford these sandstones substantial industrial value as construction materials. Durability was found to be longest in the Alcañiz stone, as a result of the geometry of its pore network.Las areniscas miocenas estudiadas han sido y son ampliamente utilizadas en patrimonio histórico y en obra civil moderna, localizándose las canteras actuales en el borde de la depresión del Ebro. Se ha realizado un exhaustivo estudio de las características petrofísicas de estos materiales, que pese a presentar la misma edad y pertenecer a la misma cuenca sedimentaria presentan características mineralógicas y texturales diferentes que les confieren diferentes propiedades físicas, mecánicas y una diferente durabilidad. Las características petrográficas y petrofísicas se han evaluado mediante la realización de ensayos según las normas UNE, NORMAL y ASTM. Para todos los ensayos se ha realizado un tratamiento estadístico de los resultados para evaluar las posibles inhomogeneidades texturales y composicionales presentes en el material y que pueden originar modificaciones en

  7. Estimation of groundwater recharge to chalk and sandstone aquifers using simple soil models

    Science.gov (United States)

    Ragab, R.; Finch, J.; Harding, R.

    1997-03-01

    On the assumption that the water draining below the root zone is potentially available for groundwater recharge, two current UK methods for estimating annual groundwater recharge have been compared with a new soil model using data from four sites under permanent grass in the UK: two sites representative of the Chalk aquifer at Bridgest Farm (Hampshire) and Fleam Dyke (Cambridgeshire), and two sites on the Triassic sandstone at Bicton College (Devon) and Bacon Hall (Shropshire). A Four Root Layers Model (FRLM), the Penman-Grindley model and the UK Meteorological Office Rainfall and Evaporation Calculation System (MORECS) were used. The new soil model was run with potential evaporation as input both from the MORECS and from the Penman-Monteith equation. The models were run for the Chalk sites both with and without a bypass flow of 15% of rainfall. Bypass was not considered for the sandstone sites. The performance of the models was tested against neutron probes measurements of soil moisture deficits. In addition, the annual groundwater recharge estimated from the models was compared with the published values obtained from the 'zero flux plane' method. Generally, the Penman-Grindley model was more successful in predicting the time for soil to return to its field capacity than in predicting the magnitude of the soil moisture deficit. The annual groundwater recharge was predicted with reasonable accuracy. The MORECS relatively tended to overestimate the soil moisture deficits and to delay the time at which the soil returns to its field capacity. The consequences were underestimates of annual groundwater recharge, owing either to the higher values of potential evaporation calculated from the MORECS or tothe high available water capacity values associated with the soils under consideration. The new soil model (FRLM) predicts the soil moisture deficits successfully and hence is reliable in estimating the annual groundwater recharge. The model is capable of doing this with

  8. Hydro-geophysical responses to the injection of CO2 in core plugs of Berea sandstone

    Science.gov (United States)

    Song, I.; Park, K. G.

    2017-12-01

    We have built a laboratory-scale core flooding system to measure the relative permeability of a core sample and the acoustic response to the CO2 saturation degree at in situ condition of pressure and temperature down to a few kilometer depths. The system consisted of an acoustic velocity core holder (AVC model from the Core Laboratories) between upstream where CO2 and H2O were injected separately and downstream where the mixed fluids came out of a core sample. Core samples with 4 cm in diameter and 5 cm in length of Berea sandstone were in turn placed in the core holder for confining and axial pressures. The flooding operations of the multiphase fluids were conducted through the sample at 40ºC in temperature and 8 MPa in backpressure. CO2 and H2O in the physical condition were injected separately into a sample at constant rate with various ratios. The two phases were mixed during flowing through the sample. The mixed fluids out of the sample were separated again by their different densities in a chamber equipped with a level gauge of the interface. From the level change of the water in the separator, we measured the volume of water coming out of the sample for each test with a constant ratio of the injection rates. Then it was possible to calculate the saturation degree of CO2 from the difference between input volume and output volume of water. The differential pressure between upstream and downstream was directly measured to calculate the relative permeability as a function of the CO2 saturation degree. We also conducted ultrasonic measurements using piezoelectric sensors on the end plugs. An electric pulse was given to a sensor on one end of sample, and then ultrasonic waves were recorded from the other end. The various ratios of injection rate of CO2 and H2O into Berea sandstone yielded a range of 0.1-0.7 in CO2 saturation degree. The relative permeability was obtained at the condition of steady-state flow for given stages from the velocity of each phase and

  9. Opening Address

    Science.gov (United States)

    Crovini, L.

    1994-01-01

    Ladies and Gentlemen To quote Mr Jean Terrien: "Physics must be one step ahead of metrology". A long-serving Director of the BIPM, he said these words when visiting the IMGC in 1970 as a member of the scientific board of our Institute. At that time it was still an open question whether the IMGC should start research work on the absolute measurement of silicon lattice spacing. Mr Terrien underlined the revolutionary character of x-ray interferometry and, eventually, he caused the balance needle to lean towards the ... right direction. Mr Terrien correctly foresaw that, like Michelson's interferometer of 1880, x-ray interferometry could have a prominent place in today's science and technology. And while, in the first case, after more than a century we can see instruments based on electromagnetic wave interaction within every one's reach in laboratories and, sometimes, in workshops, in the second case, twenty-five years since the first development of an x-ray interferometer we can witness its role in nanometrology. Today and tomorrow we meet to discuss how to go beyond the sixth decimal place in the value of the Avogadro constant. We are aware that the quest for this achievement requires the cooperation of scientists with complementary capabilities. I am sure that the present workshop is a very good opportunity to present and discuss results and to improve and extend existing cooperation. The new adjustment of fundamental constants envisaged by the CODATA Task Group is redoubling scientists' efforts to produce competitive values of NA. The results of the measurements of the silicon lattice spacing in terms of an optical wavelength, which were available for the 1986 adjustment, combined with the determination of silicon molar volume, demonstrate how such an NA determination produces a consistent set of other constants and opens the way to a possible redefinition of the kilogram. We shall see in these two days how far we have progressed along this road. For us at the

  10. Computer use, sleep duration and health symptoms

    DEFF Research Database (Denmark)

    Nuutinen, Teija; Roos, Eva; Ray, Carola

    2014-01-01

    OBJECTIVES: This study investigated whether computer use is associated with health symptoms through sleep duration among 15-year olds in Finland, France and Denmark. METHODS: We used data from the WHO cross-national Health Behaviour in School-aged Children study collected in Finland, France...... and Denmark in 2010, including data on 5,402 adolescents (mean age 15.61 (SD 0.37), girls 53 %). Symptoms assessed included feeling low, irritability/bad temper, nervousness, headache, stomachache, backache, and feeling dizzy. We used structural equation modeling to explore the mediating effect of sleep...... duration on the association between computer use and symptom load. RESULTS: Adolescents slept approximately 8 h a night and computer use was approximately 2 h a day. Computer use was associated with shorter sleep duration and higher symptom load. Sleep duration partly mediated the association between...

  11. Long Duration Space Shelter Shielding, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Physical Sciences Inc. (PSI) has developed fiber reinforced ceramic composites for radiation shielding that can be used for external walls in long duration manned...

  12. Open life science research, open software and the open century

    Directory of Open Access Journals (Sweden)

    Youhua Chen

    2015-05-01

    Full Text Available At the age of knowledge explosion and mass scientific information, I highlighted the importance of conducting open science in life and medical researches through the extensive usage of open software and documents. The proposal of conducting open science is to reduce the limited repeatability of researches in life science. I outlined the essential steps for conducting open life science and the necessary standards for creating, reusing and reproducing open materials. Different Creative Commons licenses were presented and compared of their usage scope and restriction. As a conclusion, I argued that open materials should be widely adopted in doing life and medical researches.

  13. Tectonic and sedimentological environments of sandstone-hosted uranium deposits, with special reference to the Karoo Basin of South Africa

    International Nuclear Information System (INIS)

    Le Roux, J.P.

    1985-01-01

    The principal tectonic and sedimentological settings for sandstone-hosted uranium deposits are described. Back-arc basins filled with post-Silurian, fluvial sediments bordering subduction zone magmatic arcs of calc-alkaline composition are considered favourable tectonic environments. The basins should be closed to prevent excessive oxidation of the sediments. Uranium deposits are concentrated near basin rims in the transition zone between uplift and basin subsidence, because of favourable sedimentary facies in those areas. Syn- and post-depositional deformation could have affected the localisation of uranium ore-bodies, while intrusive centres or uplifted arcs commonly have surrounding aprons of potential host rocks. Stratigraphic zoning is also related to source area tectonics and can be used to predict favourable sedimentary environments. Sedimentological processes had a direct influence on the permeability and carbonaceous matter content of sandstones and therefore have often controlled the localisation of ore-bodies. (author)

  14. Study on the relationship of the fault-block structure feature and sandstone uranium formation in Chaoshui basin north belt

    International Nuclear Information System (INIS)

    Liu Lin

    2006-12-01

    The mineralization conditions for three types of acclivity belt (Baojia Jing A' Lashan Youqi-Tangjia Gou and Taojia Jing CHAOSHUI BASIN NORTH BELT) are analyzed, according to the fault-block acclivity belt, the prospecting goal layer, the interlayer oxidized zone and uranium metallization characteristic and so on. It is considered that the positive fault-block acclivity belt favors containing oxygen and uranium water coming from eclipse source area to go into prospecting goal layer, and advanced the formation of interlayer oxidized zone and sandstone uranium metallization. The antithetic fault-block and the buried fault-block acclivity don't favors containing oxygen and uranium water into prospecting goal layer, and format difficultly interlayer oxidized belt and sandstone uranium metallization. Therefore A'Lashan Youqi-Tangjia Gou part is a uranium mineralization prospect sector. (authors)

  15. Geological and Petrophysical Characterization of the Ferron Sandstone for 3-D Simulation of a Fluvial-Deltaic Reservoir

    Energy Technology Data Exchange (ETDEWEB)

    Chidsey, Jr, Thomas C.

    2001-10-31

    The objective of the Ferron Sandstone project was to develop a comprehensive, interdisciplinary, quantitative characterization f fluvial-deltaic reservoir to allow realistic interwell and reservoir-scale models to be developed for improved oil-field development in similar reservoirs world-wide. Quantitative geological and petrophysical information on the Cretaceous Ferron Sandstone in east-central Utah was collected. Both new and existing data was integrated into a three-dimensional model of spatial variations in porosity, storativity, and tensorial rock permeability at a scale appropriate for inter-well to regional-scale reservoir simulation. Simulation results could improve reservoir management through proper infill and extension drilling strategies, reduction of economic risks, increased recovery from existing oil fields, and more reliable reserve calculations.

  16. Study on methods and techniques of aeroradiometric weak information extraction for sandstone-hosted uranium deposits based on GIS

    International Nuclear Information System (INIS)

    Han Shaoyang; Ke Dan; Hou Huiqun

    2005-01-01

    The weak information extraction is one of the important research contents in the current sandstone-type uranium prospecting in China. This paper introduces the connotation of aeroradiometric weak information extraction, and discusses the formation theories of aeroradiometric weak information extraction, and discusses the formation theories of aeroradiometric weak information and establishes some effective mathematic models for weak information extraction. Models for weak information extraction are realized based on GIS software platform. Application tests of weak information extraction are realized based on GIS software platform. Application tests of weak information extraction are completed in known uranium mineralized areas. Research results prove that the prospective areas of sandstone-type uranium deposits can be rapidly delineated by extracting aeroradiometric weak information. (authors)

  17. Satellite-Based Sunshine Duration for Europe

    Directory of Open Access Journals (Sweden)

    Bodo Ahrens

    2013-06-01

    Full Text Available In this study, two different methods were applied to derive daily and monthly sunshine duration based on high-resolution satellite products provided by the European Organisation for the Exploitation of Meteorological Satellites (EUMETSAT Satellite Application Facility on Climate Monitoring using data from Meteosat Second Generation (MSG SEVIRI (Spinning Enhanced Visible and Infrared Imager. The satellite products were either hourly cloud type or hourly surface incoming direct radiation. The satellite sunshine duration estimates were not found to be significantly different using the native 15-minute temporal resolution of SEVIRI. The satellite-based sunshine duration products give additional spatial information over the European continent compared with equivalent in situ-based products. An evaluation of the satellite sunshine duration by product intercomparison and against station measurements was carried out to determine their accuracy. The satellite data were found to be within ±1 h/day compared to high-quality Baseline Surface Radiation Network or surface synoptic observations (SYNOP station measurements. The satellite-based products differ more over the oceans than over land, mainly because of the treatment of fractional clouds in the cloud type-based sunshine duration product. This paper presents the methods used to derive the satellite sunshine duration products and the performance of the different retrievals. The main benefits and disadvantages compared to station-based products are also discussed.

  18. Strong motion duration and earthquake magnitude relationships

    International Nuclear Information System (INIS)

    Salmon, M.W.; Short, S.A.; Kennedy, R.P.

    1992-06-01

    Earthquake duration is the total time of ground shaking from the arrival of seismic waves until the return to ambient conditions. Much of this time is at relatively low shaking levels which have little effect on seismic structural response and on earthquake damage potential. As a result, a parameter termed ''strong motion duration'' has been defined by a number of investigators to be used for the purpose of evaluating seismic response and assessing the potential for structural damage due to earthquakes. This report presents methods for determining strong motion duration and a time history envelope function appropriate for various evaluation purposes, for earthquake magnitude and distance, and for site soil properties. There are numerous definitions of strong motion duration. For most of these definitions, empirical studies have been completed which relate duration to earthquake magnitude and distance and to site soil properties. Each of these definitions recognizes that only the portion of an earthquake record which has sufficiently high acceleration amplitude, energy content, or some other parameters significantly affects seismic response. Studies have been performed which indicate that the portion of an earthquake record in which the power (average rate of energy input) is maximum correlates most closely with potential damage to stiff nuclear power plant structures. Hence, this report will concentrate on energy based strong motion duration definitions

  19. Collective behaviors of book holding durations

    Science.gov (United States)

    Li, Ren-De; Guo, Qiang; Han, Jing-Ti; Liu, Jian-Guo

    2016-10-01

    Duration can directly reflect the collective reading behaviors of library user book holding. In this paper, by introducing the burstiness and memory coefficients, we empirically investigate the collective book holding behavior of three university libraries. The statistical results show that there are similar properties among the students with different backgrounds, presenting the burstiness = - 0.2 and memory = 0.5 for three datasets, which indicates that memory and random effects coexist in student book holding durations. In addition, we analyze the behavior patterns without duplicate durations by merging a series of books borrowed and returned at the same time. The results show the average burstiness B increases to -0.16 and memory M drops to 0.16 for three datasets, which indicates that both duplicate behavior and student's preference affect the memory effect. Furthermore, we present a model which assumes student's next book holding duration follows the previous one with probability p, and with probability 1 - p, the student would hold the book independently. The experimental results show that the presented model can reproduce the burstiness and memory effect of student book holding durations when p = 0.5 for empirical datasets and p = 0.2 for de-duplicate datasets, which indicate that the student's preferential holding behavior occurs with the probability p. This work helps in deeply understanding the regularity of duration-based human behaviors.

  20. Call Duration Characteristics based on Customers Location

    Directory of Open Access Journals (Sweden)

    Žvinys Karolis

    2014-05-01

    Full Text Available Nowadays a lot of different researches are performed based on call duration distributions (CDD analysis. However, the majority of studies are linked with social relationships between the people. Therefore the scarcity of information, how the call duration is associated with a user's location, is appreciable. The goal of this paper is to reveal the ties between user's voice call duration and the location of call. For this reason we analyzed more than 5 million calls from real mobile network, which were made over the base stations located in rural areas, roads, small towns, business and entertainment centers, residential districts. According to these site types CDD’s and characteristic features for call durations are given and discussed. Submitted analysis presents the users habits and behavior as a group (not an individual. The research showed that CDD’s of customers being them in different locations are not equal. It has been found that users at entertainment, business centers are tend to talk much shortly, than people being at home. Even more CDD can be distorted strongly, when machinery calls are evaluated. Hence to apply a common CDD for a whole network it is not recommended. The study also deals with specific parameters of call duration for distinguished user groups, the influence of network technology for call duration is considered.

  1. Atomoxetine Open-Label Trial in ADHD

    Directory of Open Access Journals (Sweden)

    J Gordon Millichap

    2002-07-01

    Full Text Available Atomoxetine (originally named tomoxetine, a new therapy for attention deficit hyperactivity disorder (ADHD marketed by Eli Lilly, was compared to methylphenidate in a prospective, randomized, open-label study for 10 weeks duration, at the University of Nebraska Medical Center, Massachusetts General Hospital, Mount Sinai Medical Center, Carolinas Medical Center, and Lilly Research Laboratories.

  2. Duration and extent of dysphagia following pediatric airway reconstruction.

    Science.gov (United States)

    Miller, Claire Kane; Linck, Jessica; Willging, Jay Paul

    2009-04-01

    Patients who undergo open airway reconstruction procedures are likely to experience some degree of post-operative dysphagia. This retrospective review describes the duration of post-operative dysphagia and the use of compensatory strategies in a group of 30 pediatric patients. A retrospective chart review of pediatric patients referred for post-operative swallowing assessment following airway reconstruction during a six-month period was completed. Age, sex, surgical procedure, stent type, co-morbid factors, duration of dysphagia, and use of compensatory dietary modifications and swallowing strategies was summarized and compared. Dysphagia was generally of short duration (1-5 days) in patients undergoing single stage procedures with anterior or anterior/posterior grafts. Duration of swallowing difficulty was increased in patients undergoing posterior grafts in combination with T tubes (10-14 days). The longest duration of difficulty (>2 weeks) occurred in patients who had anterior and posterior grafting with T tubes, combined with additional procedures such as vocal fold lateralization, epiglottic petiole repositioning, and/or arytenoidectomy. There was a greater likelihood of oral feeding difficulty post-operatively in patients presenting with pre-operative feeding issues such as oral aversion or specific texture refusal, and the pre-morbid need for supplemental tube feeding to supplement oral intake. Compensatory swallowing strategies were effective in decreasing aspiration associated with swallowing in oral feeders post-operatively, and in facilitating return to baseline swallowing skills. The duration of dysphagia overall was increased in patients undergoing anterior/posterior grafts in conjunction with in-dwelling T tubes, especially when combined with additional procedures. Compensatory strategies to assist with swallowing were found to be effective in the post-operative phase and included the use of a modified supraglottic swallowing sequence to assist with

  3. Study of phosphatic nodules as a possible source of uranium mineralization in warcha sandstone of nilawahan group salt range using SSNTD technique

    International Nuclear Information System (INIS)

    Qureshi, A.A.; Ullah, K.; Ullah, N.; Mohammad, A.

    2004-07-01

    The strong in the sedimentary depositional characteristics between the Warcha Sandstone of Nilawahan Group in the Salt Range and the uranium bearing sandstones of Siwalik Group in the foot hills of Himalaya and Sulaiman Ranges tempted the geologists to investigate the former group for the occurrence of any uranium deposits in it. Like volcanic ash beds in Siwaliks, phosphatic nodules may be a possible source of uranium mineralization in Warcha Sandstone of Nilawahan Group. Samples of phosphatic nodules occurring in the Sandstone of Nilawahan Group Salt Range were analyzed using Solid State Nuclear Track Detention Technique (SSNTD) for the determination of their uranium concentration. The results obtained are quite encouraging and favour the idea of exploring the area in detail for any possible occurrence of uranium deposit. Uranium concentration in these samples ranges from (434 + - 39) ppm to (964+ -81)ppm with and average concentration of (699 + - 62) ppm. (author)

  4. Wettability Alteration of Sandstone and Carbonate Rocks by Using ZnO Nanoparticles in Heavy Oil Reservoirs

    Directory of Open Access Journals (Sweden)

    Masoumeh Tajmiri

    2015-10-01

    Full Text Available Efforts to enhance oil recovery through wettability alteration by nanoparticles have been attracted in recent years. However, many basic questions have been ambiguous up until now. Nanoparticles penetrate into pore volume of porous media, stick on the core surface, and by creating homogeneous water-wet area, cause to alter wettability. This work introduces the new concept of adding ZnO nanoparticles by an experimental work on wettability alteration and oil recovery through spontaneous imbibition mechanism. Laboratory tests were conducted in two experimental steps on four cylindrical core samples (three sandstones and one carbonate taken from a real Iranian heavy oil reservoir in Amott cell. In the first step, the core samples were saturated by crude oil. Next, the core samples were flooded with nanoparticles and saturated by crude oil for about two weeks. Then, the core samples were immersed in distilled water and the amount of recovery was monitored during 30 days for both steps. The experimental results showed that oil recovery for three sandstone cores changed from 20.74, 4.3, and 3.5% of original oil in place (OOIP in the absence of nanoparticles to 36.2, 17.57, and 20.68% of OOIP when nanoparticles were added respectively. Moreover, for the carbonate core, the recovery changed from zero to 8.89% of OOIP by adding nanoparticles. By the investigation of relative permeability curves, it was found that by adding ZnO nanoparticles, the crossover-point of curves shifted to the right for both sandstone and carbonate cores, which meant wettability was altered to water- wet. This study, for the first time, illustrated the remarkable role of ZnO nanoparticles in wettability alteration toward more water-wet for both sandstone and carbonate cores and enhancing oil recovery.

  5. Main geologic characteristics of paleochannel-type sandstone-hosted uranium deposits and relevant prospecting and exploration policy

    International Nuclear Information System (INIS)

    Chen Zuyi

    1999-01-01

    The author summarizes main prospecting and exploration-related geologic characteristics of paleochannel-type sandstone-hosted uranium deposits such as the structural control over the spatial emplacement of the deposit, the near-source occurrence, the phreatic oxidation origin, the occurrence of the uranium mineralization mostly in one horizon etc. On the basis of analyzing the above characteristics the prospecting and exploration policy of such uranium deposits is proposed

  6. Economic evaluation on tight sandstone gas development projects in China and recommendation on fiscal and taxation support policies

    OpenAIRE

    Zhen Yang; Lingfeng Kong; Min Du; Chenhui Zhao

    2016-01-01

    China is rich in tight sandstone gas resources (“tight gas” for short). For example, the Sulige Gasfield in the Ordos Basin and the Upper Triassic Xujiahe Fm gas reservoir in the Sichuan Basin are typical tight gas reservoirs. In the past decade, tight gas reserve and production both have increased rapidly in China, but tight gas reservoirs are always managed as conventional gas reservoirs without effective fiscal, taxation and policy supports. The potential of sustainable tight gas productio...

  7. Mechanical properties of simulated Mars materials: gypsum-rich sandstones and lapilli tuff

    Science.gov (United States)

    Morrow, Carolyn; Lockner, David; Okubo, Chris

    2013-01-01

    Observations by the Mars Exploration Rover (MER) Opportunity, and other recent studies on diagenesis in the extensive equatorial layered deposits on Mars, suggest that the likely lithologies of these deposits are gypsum-rich sandstones and tuffaceous sediments (for example, Murchie and others, 2009; Squyres and others, 2012; Zimbelman and Scheidt, 2012). Of particular interest is how the diagenesis history of these sediments (degree of cementation and composition) influences the strength and brittle behavior of the material. For instance, fractures are more common in lower porosity materials under strain, whereas deformation bands, characterized by distributed strain throughout a broader discontinuity in a material, are common in higher porosity sedimentary materials. Such discontinuities can either enhance or restrict fluid flow; hence, failure mode plays an important role in determining the mechanics of fluid migration through sediments (Antonellini and Aydin, 1994; 1995; Taylor and Pollard, 2000; Ogilvie and Glover, 2001). As part of a larger study to characterize processes of fault-controlled fluid flow in volcaniclastic and gypsum-rich sediments on Mars, we have completed a series of laboratory experiments to focus on how gypsum clast content and degree of authigenic cementation affects the strength behavior of simulated Mars rocks. Both axial deformation and hydrostatic pressure tests were done at room temperature under dry conditions.

  8. Porosity and pore size distribution determination of Tumblagooda formation sandstone by X-ray microtomography

    International Nuclear Information System (INIS)

    Fernandes, Jaquiel S.; Appoloni, Carlos R.; Moreira, Anderson C.

    2007-01-01

    Microstructural parameters evaluations of reservoir rocks are very important to petroleum industry. This work presents total porosity and pore size distribution measurement of a sandstone sample from the Tumblagooda formation, collected at Kalbarri National Park in Australia. Porosity and pores size distribution were determined using X-Ray microtomography and imaging techniques. For these measurements, it was employed a micro-CT (μ-CT) Skyscan system model 1172 with conical beam, operated with a 1 mm Al filter at 80 kV and 125 μA, respectively, and a 2000 x 1048 pixels CCD camera. The sample was rotated from 0 deg to 180 deg, in step of 0.5 deg. For the considered sample, this equipment provided images with 2.9 μm spatial resolution. Six hundreds 2-D images where reconstructed with the Skyscan NRecon software, which were analyzed with the aid of Imago software, developed at the Laboratory of Porous Media and Thermophysical Properties (LMPT), Department of Mechanical Engineering, Federal University of Santa Catarina, Brazil, in association with the Brazilian software company Engineering Simulation and Scientific Software (ESSS), and Petroleo Brasileiro SA (PETROBRAS) Research and Development Center (CENPES). The determined average porosity was 11.45 ±1.53 %. Ninety five percent of the porous phase refers to pores with radius ranging from 2.9 to 85.2 μm, presenting the larger frequency (7.7 %) at 11.7 μm radius. (author)

  9. Experimental Study on the Effects of Stress Variations on the Permeability of Feldspar-Quartz Sandstone

    Directory of Open Access Journals (Sweden)

    Fugang Wang

    2017-01-01

    Full Text Available The multistage and discontinuous nature of the injection process used in the geological storage of CO2 causes reservoirs to experience repeated loading and unloading. The reservoir permeability changes caused by this phenomenon directly impact the CO2 injection process and the process of CO2 migration in the reservoirs. Through laboratory experiments, variations in the permeability of sandstone in the Liujiagou formation of the Ordos CO2 capture and storage (CCS demonstration project were analyzed using cyclic variations in injection pressure and confining pressure and multistage loading and unloading. The variation in the micropore structure and its influence on the permeability were analyzed based on micropore structure tests. In addition, the effects of multiple stress changes on the permeability of the same type of rock with different clay minerals content were also analyzed. More attention should be devoted to the influence of pressure variations on permeability in evaluations of storage potential and studies of CO2 migration in reservoirs in CCS engineering.

  10. Fracture propagation in sandstone and slate – Laboratory experiments, acoustic emissions and fracture mechanics

    Directory of Open Access Journals (Sweden)

    Ferdinand Stoeckhert

    2015-06-01

    Full Text Available Fracturing of highly anisotropic rocks is a problem often encountered in the stimulation of unconventional hydrocarbon or geothermal reservoirs by hydraulic fracturing. Fracture propagation in isotropic material is well understood but strictly isotropic rocks are rarely found in nature. This study aims at the examination of fracture initiation and propagation processes in a highly anisotropic rock, specifically slate. We performed a series of tensile fracturing laboratory experiments under uniaxial as well as triaxial loading. Cubic specimens with edge lengths of 150 mm and a central borehole with a diameter of 13 mm were prepared from Fredeburg slate. An experiment using the rather isotropic Bebertal sandstone as a rather isotropic rock was also performed for comparison. Tensile fractures were generated using the sleeve fracturing technique, in which a polymer tube placed inside the borehole is pressurized to generate tensile fractures emanating from the borehole. In the uniaxial test series, the loading was varied in order to observe the transition from strength-dominated fracture propagation at low loading magnitudes to stress-dominated fracture propagation at high loading magnitudes.

  11. Study on geochronology and uranium source of sandstone-type uranium deposit in Dongsheng area

    International Nuclear Information System (INIS)

    Liu Haibin; Xia Yuliang; Tian Shifeng

    2007-01-01

    This paper studied the geochronology of sandstone-type uranium deposit in the Dongsheng area of Ordos Basin. In eastern segment, ages of mineralization at the wing of the ore-roll are found to be 120 ± 5 Ma and 80 ± 5 Ma, and at the front of the ore-roll are 20 ± 2 Ma and 8 ± 1 Ma; While in middle segment, ages of mineralization are 124 ± 6 Ma and 80 ± 5 Ma. This means that the main mineralization in Dongsheng area were formed at early Jurassic and late Cretaceous, and correspondent to the time of structure uplift. Mineralization of roll-front (rich ore) which formed in Miocene and Pliocene may related to tectonic-thermal event taken place at that time and reformed the early mineralization in this area. The isochron line age of sample with uranium grade 0 ) in the sandbody is 24.64 x 10 -6 also shows the uranium pre-concentration in the strata. The even value of ΔU of rocks in Zhiluo formation is -70.2%, this shows that non-mineralized rocks have migrated uranium and acted as important metallogenic uranium sources. (authors)

  12. Depositional history of the reservoir sandstones, Akpor and Apara oilfields, eastern Niger Delta, Nigeria

    Energy Technology Data Exchange (ETDEWEB)

    Amajor, L.C.; Agbaire, D.W. (Port Harcourt Univ. (NG). Dept. of Geology)

    1989-10-01

    A subsurface study of the Agbada Formation in the Akpor and Apara oilfields in the eastern Niger Delta was undertaken in order to determine the depositional development of the reservoir sand-bodies. The study area comprises a maximum of 29 relatively thick sandstones, cyclically interbedded with shales of varying thicknesses. The lowest two sand units, separated by a shale unit and located near the base, produce petroleum from ten wells in both fields. Each sand-body exhibits a coarsening-upward textural gradient. The lower sand-body which is oval-shaped, moderately- to poorly-sorted, fine- to very coarse-grained, carbonaceous, with clay and lignite horizons, is interpreted as a deltaic sand. The unit appears to have migrated landwards, probably as a result of localized transgression, and developed maximum thickness between the two fields. The upper sand is fine-to-pebbly in grain size, well-sorted and glauconitic. Maximum development occurred slightly east of the delta. As the unit prograded in a predominantly southerly direction, genetic currents simultaneously caused it to be channelized. This sand-body is interpreted as an offshore marine bar. The intervening carbonaceous shale is thought to be of lagoonal origin. The pinch-out edges of these sand bodies may constitute prolific stratigraphic traps. (author).

  13. Numerical Investigation of Acoustic Emission Events of Argillaceous Sandstones under Confining Pressure

    Directory of Open Access Journals (Sweden)

    Zhaohui Chong

    2017-01-01

    Full Text Available At the laboratory scale, locating acoustic emission (AE events is a comparatively mature method for evaluating cracks in rock materials, and the method plays an important role in numerical simulations. This study is aimed at developing a quantitative method for the measurement of acoustic emission (AE events in numerical simulations. Furthermore, this method was applied to estimate the crack initiation, propagation, and coalescence in rock materials. The discrete element method-acoustic emission model (DEM-AE model was developed using an independent subprogram. This model was designed to calculate the scalar seismic tensor of particles in the process of movement and further to determine the magnitude of AE events. An algorithm for identifying the same spatiotemporal AE event is being presented. To validate the model, a systematic physical experiment and numerical simulation for argillaceous sandstones were performed to present a quantitative comparison of the results with confining pressure. The results showed good agreement in terms of magnitude and spatiotemporal evolution between the simulation and the physical experiment. Finally, the magnitude of AE events was analyzed, and the relationship between AE events and microcracks was discussed. This model can provide the research basis for preventing seismic hazards caused by underground coal mining.

  14. Experimental evaluation on the damages of different drilling modes to tight sandstone reservoirs

    Directory of Open Access Journals (Sweden)

    Gao Li

    2017-07-01

    Full Text Available The damages of different drilling modes to reservoirs are different in types and degrees. In this paper, the geologic characteristics and types of such damages were analyzed. Then, based on the relationship between reservoir pressure and bottom hole flowing pressure corresponding to different drilling modes, the experimental procedures on reservoir damages in three drilling modes (e.g. gas drilling, liquid-based underbalanced drilling and overbalanced drilling were designed. Finally, damage simulation experiments were conducted on the tight sandstone reservoir cores of the Jurassic Ahe Fm in the Tarim Basin and Triassic Xujiahe Fm in the central Sichuan Basin. It is shown that the underbalanced drilling is beneficial to reservoir protection because of its less damage on reservoir permeability, but it is, to some extent, sensitive to the stress and the empirical formula of stress sensitivity coefficient is obtained; and that the overbalanced drilling has more reservoir damages due to the invasion of solid and liquid phases. After the water saturation of cores rises to the irreducible water saturation, the decline of gas logging permeability speeds up and the damage degree of water lock increases. It is concluded that the laboratory experiment results of reservoir damage are accordant with the reservoir damage characteristics in actual drilling conditions. Therefore, this method reflects accurately the reservoir damage characteristics and can be used as a new experimental evaluation method on reservoir damage in different drilling modes.

  15. Strain localization and elastic-plastic coupling during deformation of porous sandstone

    Energy Technology Data Exchange (ETDEWEB)

    Dewers, Thomas A. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States). Geomechanics Dept.; Issen, Kathleen A. [Clarkson Univ., Potsdam, NY (United States). Mechanical and Aeronautical Engineering; Holcomb, David J. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States). Geomechanics Dept.; Olsson, William A. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States). Geomechanics Dept.; Ingraham, Mathew D. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States). Geomechanics Dept.

    2017-09-12

    Results of axisymmetric compression tests on weak, porous Castlegate Sandstone (Cretaceous, Utah, USA), covering a range of dilational and compactional behaviors, are examined for localization behavior. Assuming isotropy, bulk and shear moduli evolve as increasing functions of mean stress and Mises equivalent shear stress respectively, and as decreasing functions of work-conjugate plastic strains. Acoustic emissions events located during testing show onset of localization and permit calculation of observed shear and low-angle compaction localization zones, or bands, as localization commences. Total strain measured experimentally partitions into: A) elastic strain with constant moduli, B) elastic strain due to stress dependence of moduli, C) elastic strain due to moduli degradation with increasing plastic strain, and D) plastic strain. The third term is the elastic-plastic coupling strain, and though often ignored, contributes significantly to pre-failure total strain for brittle and transitional tests. Constitutive parameters and localization predictions derived from experiments are compared to theoretical predictions. In the brittle regime, predictions of band angles (angle between band normal and maximum compression) demonstrate good agreement with observed shear band angles. Compaction localization was observed in the transitional regime in between shear localization and spatially pervasive compaction, over a small range of mean stresses. In contrast with predictions however, detailed acoustic emissions analyses in this regime show low angle, compaction-dominated but shear-enhanced, localization.

  16. Geology and recognition criteria for roll-type uranium deposits in continental sandstones. Final report

    International Nuclear Information System (INIS)

    Harshman, E.N.; Adams, S.S.

    1981-01-01

    The study of roll-type deposits during the past 20 years, since the first description of a deposit in the United States, has developed general concepts of ore formation which are accepted widely and are compatible with available data. If this were not the case the concepts would not have endured and could not have been so successfully applied to exploration using the relations of altered-unaltered sandstone. The comparative simplicity of the model, and the ease with which it has been applied to exploration have, oddly enough, probably inhibited detailed studies of ore districts that would have provided data now needed for refinement of ore controls for exploration and resource assessment programs. The most thorough study of a roll-type district was that of the Shirley Basin which is drawn on heavily in this report. The general concept of roll-type formation provides a strong basis for the development of geological observations and guides, or recognition criteria, for resource studies and exploration. Indeed, industry has been developing and using them for 20 years. As the objective of this study was to identify the most useful recognition criteria and develop a method for their systematic use in resource studies and exploration, the study is best summarized by reference to the important geological observations about roll-type deposits

  17. Diagenetic Evolution and Reservoir Quality of Sandstones in the North Alpine Foreland Basin: A Microscale Approach.

    Science.gov (United States)

    Gross, Doris; Grundtner, Marie-Louise; Misch, David; Riedl, Martin; Sachsenhofer, Reinhard F; Scheucher, Lorenz

    2015-10-01

    Siliciclastic reservoir rocks of the North Alpine Foreland Basin were studied focusing on investigations of pore fillings. Conventional oil and gas production requires certain thresholds of porosity and permeability. These parameters are controlled by the size and shape of grains and diagenetic processes like compaction, dissolution, and precipitation of mineral phases. In an attempt to estimate the impact of these factors, conventional microscopy, high resolution scanning electron microscopy, and wavelength dispersive element mapping were applied. Rock types were established accordingly, considering Poro/Perm data. Reservoir properties in shallow marine Cenomanian sandstones are mainly controlled by the degree of diagenetic calcite precipitation, Turonian rocks are characterized by reduced permeability, even for weakly cemented layers, due to higher matrix content as a result of lower depositional energy. Eocene subarkoses tend to be coarse-grained with minor matrix content as a result of their fluvio-deltaic and coastal deposition. Reservoir quality is therefore controlled by diagenetic clay and minor calcite cementation.Although Eocene rocks are often matrix free, occasionally a clay mineral matrix may be present and influence cementation of pores during early diagenesis. Oligo-/Miocene deep marine rocks exhibit excellent quality in cases when early cement is dissolved and not replaced by secondary calcite, mainly bound to the gas-water contact within hydrocarbon reservoirs.

  18. Feasibility of a data-constrained prediction of hydrocarbon reservoir sandstone microstructures

    International Nuclear Information System (INIS)

    Yang, Y S; Gureyev, T E; Tulloh, A; Clennell, M B; Pervukhina, M

    2010-01-01

    Microstructures are critical for defining material characteristics such as permeability, mechanical, electrical and other physical properties. However, the available techniques for determining compositional microstructures through segmentation of x-ray computed tomography (CT) images are inadequate when there are finer structures than the CT spatial resolution, i.e. when there is more than one material in each voxel. This is the case for CT imaging of geomaterials characterized with submicron porosity and clay coating that control petrophysical properties of rock. This note outlines our data-constrained modelling (DCM) approach for prediction of compositional microstructures, and our investigation of the feasibility of determining sandstone microstructures using multiple CT data sets with different x-ray beam energies. In the DCM approach, each voxel is assumed to contain a mixture of multiple materials, optionally including voids. Our preliminary comparisons using model samples indicate that the DCM-predicted compositional microstructure is consistent with the known original microstructure under low noise conditions. The approach is quite generic and is applicable to predictions of microstructure of various materials. (technical design note)

  19. Delineating spring recharge areas in a fractured sandstone aquifer (Luxembourg) based on pesticide mass balance

    Science.gov (United States)

    Farlin, J.; Drouet, L.; Gallé, T.; Pittois, D.; Bayerle, M.; Braun, C.; Maloszewski, P.; Vanderborght, J.; Elsner, M.; Kies, A.

    2013-06-01

    A simple method to delineate the recharge areas of a series of springs draining a fractured aquifer is presented. Instead of solving the flow and transport equations, the delineation is reformulated as a mass balance problem assigning arable land in proportion to the pesticide mass discharged annually in a spring at minimum total transport cost. The approach was applied to the Luxembourg Sandstone, a fractured-rock aquifer supplying half of the drinking water for Luxembourg, using the herbicide atrazine. Predictions of the recharge areas were most robust in situations of strong competition by neighbouring springs while the catchment boundaries for isolated springs were extremely sensitive to the parameter controlling flow direction. Validation using a different pesticide showed the best agreement with the simplest model used, whereas using historical crop-rotation data and spatially distributed soil-leaching data did not improve predictions. The whole approach presents the advantage of integrating objectively information on land use and pesticide concentration in spring water into the delineation of groundwater recharge zones in a fractured-rock aquifer.

  20. The importance of dissolved free oxygen during formation of sandstone-type uranium deposits

    Science.gov (United States)

    Granger, Harry Clifford; Warren, C.G.

    1979-01-01

    One factor which distinguishes t, he genesis of roll-type uranium deposits from the Uravan Mineral Belt and other sandstone-type uranium deposits may be the presence and concentration of dissolved free oxygen in the ore-forming. solutions. Although dissolved oxygen is a necessary prerequisite for the formation of roll-type deposits, it is proposed that a lack of dissolved oxygen is a prerequisite for the Uravan deposits. Solutions that formed both types of deposits probably had a supergene origin and originated as meteoric water in approximate equilibrium with atmospheric oxygen. Roll-type deposits were formed where the Eh dropped abruptly following consumption of the oxygen by iron sulfide minerals and creation of kinetically active sulfur species that could reduce uranium. The solutions that formed the Uravan deposits, on the other hand, probably first equilibrated with sulfide-free ferrous-ferric detrital minerals and fossil organic matter in the host rock. That is, the uraniferous solutions lost their oxygen without lowering their Eh enough to precipitate uranium. Without oxygen, they then. became incapable of oxidizing iron sulfide minerals. Subsequent localization and formation of ore bodies from these oxygen-depleted solutions, therefore, was not necessarily dependent on large reducing capacities.