WorldWideScience

Sample records for sandstone member consists

  1. Diagenesis of Paleogene sandstone from Kong 1 Member of Southern Kongdian in Huanghua depression

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Huanghua depression is one of the richest areas in petroleum and natural gas in China. The Paleogene mainly consists of sandstone with facies of river, delta, fan delta and littoral-shallow lacustrine. Diagenesis played an important role in the properties of reservoir rocks. Applying X-ray diffraction, on the basis of analyzing many cores and thin sections, the authors studied diagenesis of Paleogene sandstone reservoir rocks in kongl Menber of southern Kongdian in Huanghua depression. Diagenetic complexity shows that the sandstone in this area underwent compaction, cementation, isolation, recrystallization during the burying of sediments, and the first three compose the major diagenesis. The compaction and cementation led to decreasing porosity, and the solution of unsteady minerals also results in increasing in porosity.

  2. Petrofacies, provenance and diagenesis of the dhosa sandstone member (Chari Formation) at Ler, Kachchh sub-basin, Western India

    Science.gov (United States)

    Ahmad, A. H. M.; Bhat, G. M.

    2006-10-01

    The sandstones of the Dhosa Sandstone Member of Late Callovian and Early Oxfordian age exposed at Ler have been analyzed for their petrofacies, provenance, tectonic setting and diagenetic history. These sandstones are fine to medium grained and poorly- to well sorted. The constituent mineral grains are subangular to subrounded. These sandstones were derived from a mixed provenance including granites, granite-gneisses, low- and high-grade metamorphic and some basic rocks of the Aravalli Range and Nagarparkar Massif. The petrofacies analysis reveals that these sandstones belong to the continental block-, recycled orogen- and rifted continental margin tectonic regime. The imprints of early and deep burial diagenesis of these sandstones include different stages of compaction, cementation, change in crystal boundaries, cement-cement boundaries, chertification and neomorphism. The sequence of cementation includes precipitation of calcite and its subsequent replacement by Fe calcite and silica cements. The typical intermediate burial (2-3 km depth) diagenetic signatures of these sandstones are reflected in the formation of suture and straight-line boundaries, and triple junctions with straight-line boundaries. The depositional environment, relatively low-energy environment that was below storm wave base but subjected to gentle currents, of the Dhosa Sandstone Member controlled the early diagenesis, which in turn influenced the burial diagenesis of these sandstones.

  3. Fracture network of the Ferron Sandstone Member of the Mancos Shale, east-central Utah, USA

    Science.gov (United States)

    Condon, S.M.

    2003-01-01

    The fracture network at the outcrop of the Ferron Sandstone Member of the Mancos Shale was studied to gain an understanding of the tectonic history of the region and to contribute data to studies of gas and water transmissivity related to the occurrence and production of coal-bed methane. About 1900 fracture readings were made at 40 coal outcrops and 62 sandstone outcrops in the area from Willow Springs Wash in the south to Farnham dome in the north of the study area in east-central Utah.Two sets of regional, vertical to nearly vertical, systematic face cleats were identified in Ferron coals. A northwest-striking set trends at a mean azimuth of 321??, and a northeast-striking set has a mean azimuth of 55??. Cleats were observed in all coal outcrops examined and are closely spaced and commonly coated with thin films of iron oxide.Two sets of regional, systematic joint sets in sandstone were also identified and have mean azimuths of 321?? and 34??. The joints of each set are planar, long, and extend vertically to nearly vertically through multiple beds; the northeast-striking set is more prevalent than the northwest-striking set. In some places, joints of the northeast-striking set occur in closely spaced clusters, or joint zones, flanked by unjointed rock. Both sets are mineralized with iron oxide and calcite, and the northwest-striking set is commonly tightly cemented, which allowed the northeast-striking set to propagate across it. All cleats and joints of these sets are interpreted as opening-mode (mode I) fractures. Abutting relations indicate that the northwest-striking cleats and joints formed first and were later overprinted by the northeast-striking cleats and joints. Burial curves constructed for the Ferron indicate rapid initial burial after deposition. The Ferron reached a depth of 3000 ft (1000 m) within 5.2 million years (m.y.), and this is considered a minimum depth and time for development of cleats and joints. The Sevier orogeny produced southeast

  4. Sandstone-body structures and ephemeral stream processes in the Dinosaur Canyon Member, Moenave Formation (Lower Jurassic), Utah, U.S.A.

    Science.gov (United States)

    Olsen, Henrik

    1989-02-01

    Studies of fluvial sandstone-body structures in the Lower Jurassic Dinosaur Canyon Member suggest a threefold subdivision of the ephemeral stream deposits. Sandstone-sheets with interbedded siltstones are less than 1 m thick and laterally extensive for hundreds of metres. They are interpreted as sheetflood deposits. Simple channel sandstone-bodies are a few metres thick and a few tens of metres wide. They reflect solitary channel incision, episodic migration and plugging. Multistorey channel sandstone-bodies are a few metres thick and laterally extensive for hundreds of metres. They are composed of several channel-shaped storeys and exhibit only local incision. The multistorey sandstone-bodies are interpreted as braided ephemeral stream deposits. Two sandstone-sheet subtypes with grooves and mounds, respectively, are interpreted as intermediate between the sheetflood deposits and solitary incised channel deposits on one hand and between sheetflood deposits and braided stream deposits on the other hand. The solitary channels and braided streams are accordingly interpreted to be initiated from sheetfloods through differential erosion and differential deposition, respectively. This model of channel evolution from sheetfloods is probably applicable to other semiarid and arid fluvial environments dominated by surface runoff.

  5. Petrography and diagenesis of Gomo member sandstones - Candeias Formation (lower cretaceous) Rio do Buoil field, Reconcavo Basin; Petrografia e diagenese dos arenitos do Membro Gomo - Formacao Candeias (Cretaceo Inferior) no Campo de Rio do Bu, Bacia do Reconcavo

    Energy Technology Data Exchange (ETDEWEB)

    Mato, Luiz F.; Souza, Edson M. [PETROBRAS, BA (Brazil). Distrito de Exploracao

    1988-04-01

    Characteristics, textural and compositional aspects, analyse the provenance and diagenetic evolution of the Gomo Member/Candeias Formation sandstones (Lower Cretaceous) in the Rio do Bu oil field, Reconcavo Basin, are discussed. Studies of sandstone petrography, shales and carbonates associated, diagenetic sequence, rifts fractures and cementation characterization, are also analyzed. 17 figs., 2 tabs., 19 refs

  6. Controls on the Lower Cretaceous Punt Sandstone Member, a massive deep-water clastic deposystem, Inner Moray Firth, UK North Sea

    Energy Technology Data Exchange (ETDEWEB)

    Argent, J.D.; Stewart, S.A. [Amerada Hess Ltd., London (United Kingdom); Underhill, J.R. [University of Edinburgh (United Kingdom). Dept. of Geology and Geophysics

    2000-08-01

    Interpretation of high-quality seismic data, constrained by exploration wells, provides insights into controls on the stratigraphic architecture and deep-water sedimentary processes that governed deposition of the Lower Cretaceous Punt Sandstone Member in the Inner Moray Firth Basin. We suggest a model of deposition in which sediment provenance from the north and west progressively filled depositional accommodation in proximal depocentres before spilling into more distal areas via linear, confined and incised channel complexes. As well as giving important clues into post-rift depositional processes in the basin, and a well-imaged ancient analogue for the deposition of massive deep-water sands, the seismic and stratigraphic data may also provide important insights into factors governing the poorly imaged Lower Cretaceous sands in neighbouring basins of the North Sea. (Author)

  7. How leader-member exchange, work engagement and HRM consistency explain Chinese luxury hotel employees’ job performance

    NARCIS (Netherlands)

    Li, X.; Sanders, K.; Frenkel, S.

    2012-01-01

    This paper provides insights into the relationship between leader-member exchange (LMX) and employee job performance. An integrative model that includes work engagement and human resource management (HRM) consistency, defined as the extent to which various HR practices are viewed as consistent with

  8. How leader-member exchange, work engagement and HRM consistency explain Chinese luxury hotel employees’ job performance

    NARCIS (Netherlands)

    Li, X.; Sanders, Karin; Frenkel, S.

    2012-01-01

    This paper provides insights into the relationship between leader-member exchange (LMX) and employee job performance. An integrative model that includes work engagement and human resource management (HRM) consistency, defined as the extent to which various HR practices are viewed as consistent with

  9. Facies analysis and sequence stratigraphy review of Ponta Grossa formation, Parana Basin - emphasis on the Tibagi Member sandstones; Analise de facies e revisao da estratigrafia de sequencias da Formacao Ponta Grossa, Bacia do Parana - enfase nos arenitos do Membro Tibagi

    Energy Technology Data Exchange (ETDEWEB)

    Candido, Ary Gustavo [PETROBRAS, Campos dos Goytacases, RJ (Brazil). Unidade de Negocio Exploracao e Producao da Bacia de Campos. Gerencia de Avaliacao de Blocos e Interpretacao Geologica e Geofisica]. E-mail: ary.candido@petrobras.com.br; Rostirolla, Sidnei Pires

    2006-11-15

    Lithostratigraphic studies of Ponta Grossa Formation (Devonian - Parana Basin) suggest the recognition of three members, denominated: Jaguariaiva Member, Tibagi Member and Sao Domingos Member. This work studies the formation as a whole, but predominantly the Tibagi Member, the most controversial, regarding its stratigraphic genesis. Differing from the other members, that are predominantly pelitic, the Tibagi Member has a sandy composition with the facies; distal storm, proximal storm, deltaic outlet bars and littoral drift currents. The disposition of these facies, formed in marine transitional environment, reveals deposition with a pro gradational array, beginning in shallow platformal environment, with strong storm influence, and covered by deltaic outlet bar deposits. Finally, the coastal drift currents process prevailed. Based on the facies analysis and the comparison between gamma-ray profiles of outcrops and geophysical profiles of wells, the formation was divided in two depositional sequences. In the upper sequence, where it is suggested that Tibagi Member sandstones represent deposits formed in a tract similar to a shelf edge systems tract. This system tract was used (elaborated for passive margin basins, and not for ramp type basins, as the Parana Basin), to have the possibility of obtaining good explanations to understand the deltaic progradation associated with the deposition of that interval, clarifying issues referring to the relative sea level behavior, to the sedimentary contribution, and to the stratigraphic pile up. Finally, comparisons were made with existing stratigraphic models, with the aim to establish a discussion on this important subject in order to promote new debate on the Ponta Grossa Formation stratigraphic sequences. (author)

  10. Diagenesis and diagenetic facies of low porosity and permeability sandstone in Member 8 of the Yanchang Formation in Daijiaping area, Ordos Basin%鄂尔多斯盆地代家坪地区延长组8段低孔渗砂岩成岩作用及成岩相

    Institute of Scientific and Technical Information of China (English)

    周翔; 何生; 陈召佑; 王芙蓉; 周思宾; 刘萍

    2016-01-01

    上三叠统延长组长8段砂岩是鄂尔多斯盆地代家坪地区重要的勘探目的层,以长石岩屑细砂岩和岩屑长石细砂岩为主,目前处于中成岩A期,属典型低孔特低渗储层.强烈的成岩作用是储层致密化的主要原因,其中压实作用和碳酸盐岩胶结作用造成储层原生孔隙大量丧失,绿泥石胶结和长石溶蚀对储层物性改善起到了积极作用,碱-酸-碱交替的成岩介质环境变化控制了粘土矿物形成、碳酸盐胶结物沉淀以及长石溶蚀作用.综合多项定性和定量参数,将长8段砂岩划分为5种成岩相类型,定量计算不同成岩相埋藏过程中孔隙演化表明,由沉积作用形成的不同成岩相中砂岩原始组分差异是导致胶结类型和溶蚀程度差异的物质基础,不同成岩相中成岩作用类型及强度是造成砂岩孔隙演化及物性差异的主要原因.优质砂岩储层分布与成岩相密切相关,其中分布于水下分流河道砂体中的弱压实绿泥石胶结相和中压实次生溶蚀相砂岩物性最好,是研究区长8段砂岩储层中最有利的成岩相带.%Member 8 sandstone of the Upper Triassic Yanchang Formation is the major exploration target in Daijiaping area , Ordos Basin .Member 8 sandstone of the Yanchang Formation mainly consists of feldspathic litharenite and lithic arkose , currently is at the A phase of middle diagenesis stage ,and is categorized into low-porosity and extremely low-permeability reservoir .The intensive diagenesis is main cause of reservoir densification .Compaction and carbonate cementation largely reduce the primary porosity ,while chlorite cementation and feldspar dissolution improve the reservoir quality ,and the alka-line-acidic-alkaline change of digenetic environment control the formation of clay mineral ,the precipitation of carbonate ce-ments,and the dissolution of feldspar .Five types of diagenetic facies are identified in the Member 8 sandstone of the Yan

  11. CO2 Storage Potential of the Eocene Tay Sandstone, Central North Sea, UK

    Science.gov (United States)

    Gent, Christopher; Williams, John

    2017-04-01

    Carbon Capture and Storage (CCS) is crucial for low-carbon industry, climate mitigation and a sustainable energy future. The offshore capacity of the UK is substantial and has been estimated at 78 Gt of CO2 in saline aquifers and hydrocarbon fields. The early-mid Eocene Tay Sandstone Member of the Central North Sea (CNS) is a submarine-fan system and potential storage reservoir with a theoretical capacity of 123 Mt of CO2. The Tay Sandstone comprises of 4 sequences, amalgamating into a fan complex 125km long and 40 km at a minimum of 1500 m depth striking NW-SE, hosting several hydrocarbon fields including Gannett A, B, D and Pict. In order to better understand the storage potential and characteristics, the Tay Sandstone over Quadrant 21 has been interpreted using log correlation and 3D seismic. Understanding the internal and external geometry of the sandstone as well as the lateral extent of the unit is essential when considering CO2 vertical and horizontal fluid flow pathways and storage security. 3D seismic mapping of a clear mounded feature has revealed the youngest sequence of the Tay complex; a homogenous sand-rich channel 12 km long, 1.5 km wide and on average 100 m thick. The sandstone has porosity >35%, permeability >5 D and a net to gross of 0.8, giving a total pore volume of 927x106 m3. The remaining three sequences are a series of stacked channels and interbedded mudstones which are more quiescent on the seismic, however, well logs indicate each subsequent sequence reduce in net to gross with age as mud has a greater influence in the early fan system. Nevertheless, the sandstone properties remain relatively consistent and are far more laterally extensive than the youngest sequence. The Tay Sandstone spatially overlaps several other potential storage sites including the older Tertiary sandstones of the Cromarty, Forties and Mey Members and deeper Jurassic reservoirs. This favours the Tay Sandstone to be considered in a secondary or multiple stacked

  12. Upper Jurassic - Lower Cretaceous turbidite sandstones in the Central Graben, North Sea; with special focus on the Danish Gertrud Graben

    Energy Technology Data Exchange (ETDEWEB)

    Johannessen, P.

    1998-10-01

    Thick Late Jurassic - Early cretaceous turbidite sandstone successions in the Central Graben are uncommon except from the Moray Firth and Viking Graven north of the Central Graben, where several important hydrocarbon producing turbidite sandstone fields are known. The only hydrocarbon producing turbidite reservoir sandstones in the Central Graben is the up to 55 m thick Ribble Sandstone Member located in the British South-west Central Graben, where it is lying above thick shoreface reservoir sandstones of the Fulmar Formation, separated by offshore claystones of the Kimmeridge Clay Formation. The turbidite sandstones of the Ribble Sandstone Member derived from the more proximal thick reservoir sandstones of the Fulmar Formation located near the Mid North Sea High. It has not yet been possible to correlate thick shoreface sandstones of the Norwegian Ula Formation or the Danish Heno Formation to more distal thick turbidite sandstones derived from the shoreface sandstones. (au) 60 fig., 85 refs.

  13. Kaolinite Mobilisation in Sandstone

    DEFF Research Database (Denmark)

    Rosenbrand, Esther; Fabricius, Ida Lykke; Kets, Frans

    2013-01-01

    The effect of temperature and salinity on sandstone permeability is critical to the feasibility of heat storage in geothermal aquifers. Permeability reduction has been observed in Berea sandstone when the salinity of the pore water is reduced as well as when the sample is heated. Several authors...

  14. Study on Mechanism of Low Permeability Sandstone Gas Reservoir in Fourth Member of Xujiahe in Guang An Gas Field%广安气田须四段低渗砂岩气藏渗流机理研究

    Institute of Scientific and Technical Information of China (English)

    李辉; 王燕; 欧剑; 许涛; 汪娟

    2013-01-01

    On the basis of a detailed analysis of the reservoir characteristics, from the capillary pressure, reservoir structure characteristics, percolation characteristics of the two-phase, gas single -phase low-speed and water lock, oil lock damage, etc. develop detailed study on the mechanism of low permeability sandstone gas reservoir in Fourth Member of Xujiahe in Guangan Gas Field seepage. Results show that: low permeability sandstone gas reservoir porosity is concentrated in the range of 3% to 7% , penetration concentrated between 0.001 × 10-3 μm ~ 16. 2 × 10-3μm2, it belongs to a typical low porosity and low permeability gas reservoirs; capillary pressure curve has a bimodal characteristics, it' s a moderate deviation reservoir, the pore throats value radius 0. 1 μm as a division of the reservoir and non- reservoir boundaries; coexistence of gas and water permeability reservoir , gas seepage by the slippage effect and capillary forces affect the slow seepage stage , the capillary force of the impact is more obvious, and gas seepage produce low velocity non-Darcy flow phenomena. Reservoir initial water saturation , with movable water can be taken out , water blocking damage will be improved , but the increase in the amount of precipitation of condensate , easy to form at the throat " Jamin effect" increase the gas flow resistance , impact gas well production capacity , resulting in damage to the oil lock.%在对储层特征进行详细分析的基础上,从毛管压力、储层结构特征、两相渗流特征、气体单相低速渗流特征和水锁、油锁损害等方面,深入研究了广安气田须四段低渗砂岩气藏渗流机理.研究结表明:须四段低渗砂岩气藏孔隙度集中在3%~7%之间,渗透率集中在0.001×10-3 μm2 ~ 16.2×10-3 μm2之间,属典型的低孔、低渗气藏.毛管压力曲线具有双峰态特征,属于中等偏差储层,孔喉中值半径0.1 μm可作为划分储层与非储层的界限.低渗储层气水

  15. The age of 47Tuc from self-consistent isochrone fits to colour-magnitude diagrams and the eclipsing member V69

    DEFF Research Database (Denmark)

    Brogaard, K.; VandenBerg, D. A.; Bedin, L. R.

    2017-01-01

    completely self-consistent isochrone fitting method to ground based and $\\textit{HST}$ cluster colour-magnitude diagrams and the eclipsing binary member V69. The analysis suggests that the composition of V69, and by extension one of the populations of $47\\,$Tuc, is given by [Fe/H]$\\sim-0.70$, [O/Fe]$\\sim+0...

  16. Analysis of Radiation Exposure for Naval Personnel at Operation SANDSTONE.

    Science.gov (United States)

    1983-08-15

    Operation SANDSTONE Dose Reconstruction Methodology I I 2-1 Enewetak Atoll Anchorage Areas 14 2-2 Destroyer Patrol Sector Chart for Operation SANDSTONE 18...2-3 Average Free-Field Radiation Intensity for Southern and Northern Anchorage Areas - Enewetak Atoll 24 2-4 Average Free-Field Radiation Intensity...Operation SANDSTONE was the second nuclear test series held in the Marshall 0 Islands. It consisted of three nuclear weapon tests at Enewetak * Atoll in

  17. The stratigraphy of Oxfordian-Kimmeridgian (Late Jurassic) reservoir sandstones in the Witch Ground Graben, United Kingdom North Sea

    Energy Technology Data Exchange (ETDEWEB)

    Harker, S.D. (Elf Enterprise Caledonia Ltd., Aberdeen (United Kingdom)); Mantel, K.A. (Narwhal, London (United Kingdom)); Morton, D.J. (Deminex UK Oil Gas Ltd., London (United Kingdom)); Riley, L.A. (Paleo Services, Hertfordshire (United Kingdom))

    1993-10-01

    Oil-bearing Upper Jurassic Oxfordian-Kimmeridgian sandstones of the Sgiath and Piper formations are of major economic importance in the Witch Ground Gaben, United Kingdom North Sea. They form the reservoirs in 14 fields that originally contained 2 billion bbl of oil reserves, including Scott Field, which in 1993 will be the largest producing United Kingdom North Sea oil field to come on stream in more than a decade. The Sgiath and Piper formations represent Late Jurassic transgressive and regressive phases that began with paralic deposition and culminated in a wave-dominated delta system. These phases preceded the major grabel rifting episode (late Kimmeridgian to early Ryazanian) and deposition of the Kimmeridge Clay Formation, the principal source rock of the Witch Ground Graben oil fields. A threefold subdivision of the middle to upper Oxfordian Sgiath Formation is formally proposed, with Scott field well 15/21a-15 as the designated reference well. The basal Skene Member consists of thinly interbedded paralic carbonaceous shales, coals, and sandstones. This is overlain by transgressive marine shales of the Saltire Member. The upper-most Oxfordian Scott Member consists of shallow marine sandstones that prograded to the southwest. The contact of the Sgiath and Piper formations is a basinwide transgressive marine shale (I shale), which can act as an effective barrier to fluid communication between the Sgiath and Piper reservoir sandstones.

  18. Cathodoluminescence investigations on quartz cement in sandstones of Khabour Formation from Iraqi Kurdistan region, northern Iraq

    DEFF Research Database (Denmark)

    Omer, Muhamed Fakhri; Friis, Henrik

    The Ordovician deltaic to shallow marine Khabour Formation in Northern Iraq consists mainly of sandstone with minor siltstone and interbedded shale. The sandstones are pervasively cemented by quartz that resulted in very little preserved primary porosity. Cathodoluminescence and petrographic stud...

  19. Altitude of the bottom of the Trinidad Sandstone in the Raton Basin, Las Animas County, Colorado

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This data set consists of structure contours that show lines of equal altitude of the bottom of the Trinidad Sandstone, the contact between the Trinidad Sandstone...

  20. Immunolocalisation of members of the polypeptide N-acetylgalactosaminyl transferase (ppGalNAc-T) family is consistent with biologically relevant altered cell surface glycosylation in breast cancer

    DEFF Research Database (Denmark)

    Brooks, Susan A; Carter, Tracey M; Bennett, Eric P;

    2007-01-01

    understood, may mediate the synthesis of varied glycoforms of cellular proteins with different biological activities. Disruptions in glycosylation are a common feature of cancer and may have functional significance. Immunocytochemistry with confocal scanning laser microscopy was employed to detect members......,475). They stably synthesise varying levels, consistent with origin and phenotype, of aberrantly glycosylated glycoproteins featuring exposed, terminal GalNAc residues, including the cancer-associated Tn antigen, which, in numerous studies, have been associated with metastatic competence and poor cancer prognosis...

  1. Stochastic reconstruction of sandstones

    Science.gov (United States)

    Manwart; Torquato; Hilfer

    2000-07-01

    A simulated annealing algorithm is employed to generate a stochastic model for a Berea sandstone and a Fontainebleau sandstone, with each a prescribed two-point probability function, lineal-path function, and "pore size" distribution function, respectively. We find that the temperature decrease of the annealing has to be rather quick to yield isotropic and percolating configurations. A comparison of simple morphological quantities indicates good agreement between the reconstructions and the original sandstones. Also, the mean survival time of a random walker in the pore space is reproduced with good accuracy. However, a more detailed investigation by means of local porosity theory shows that there may be significant differences of the geometrical connectivity between the reconstructed and the experimental samples.

  2. Micro pore and throat characteristics and moveable fluid variation of tight sandstone in 4th member of Xujiahe Formation, Xinchang Gas Field, western Sichuan Basin%川西新场须四段致密砂岩储层微观孔喉与可动流体变化特征

    Institute of Scientific and Technical Information of China (English)

    肖开华; 冯动军; 李秀鹏

    2014-01-01

    In order to evaluate the tight sandstone reservoirs in the 4th member of the Xujiahe Formation in the Xinchang area of the western Sichuan Basin, nuclear magnetic resonance and constant-rate mercury intrusion ex-periments have been carried out to quantitatively analyze micro pore and throat and moveable fluid variation char-acteristics. Studies have indicated that the moveable fluid parameters, throat parameters and pore parameters of tight sandstones vary largely. In micro-fractured tight sandstones, pores have an advantage over throats affecting the moveable fluid parameters, and the moveable fluid parameters are mainly controlled by pores. Low moveable fluid content and low producing degree of tight sandstones are mainly caused by the relatively long radius and wide distribution of pores and throats. In micro-fractured tight sandstones, the mercury saturation in throats is higher than that in pores, indicating that the dominant type of reservoir space is pore-fracture type in the 4th member of the Xujiahe Formation, the Xinchang Gas Field.%为了评价川西新场须四段致密砂岩储层,应用恒速压汞及核磁共振实验方法对储层微观孔喉与可动流体变化特征进行定量分析。结果表明,须四段致密砂岩储层可动流体参数、喉道特征参数及孔隙参数变化幅度大。微裂隙发育的致密砂岩储层孔隙对可动流体参数的影响较喉道要更大一些,在微观上可动流体参数主要受孔隙控制。孔喉半径比较大、分布范围宽是致密砂岩储层可动流体含量低、可动用程度差的主要原因之一。微裂隙发育的致密砂岩储层具有喉道进汞饱和度较孔隙进汞饱和度高的特点,说明新场须四段致密砂岩储层的储集空间类型主要为孔隙-裂缝型。

  3. Comparison analysis of fractal characteristics for tight sandstones using different calculation methods

    Science.gov (United States)

    Zhang, Xiaoyang; Wu, Caifang; Li, Teng

    2017-02-01

    The micropore structure of a tight sandstone is the decisive factor in determining its reserve and seepage characteristics. An accurate description of the pore structures and a complete characterization of the gas-water permeability are critical when exploring for tight sandstone gas. One simple and effective way to quantitatively characterize the heterogeneity and complexity of the pore structures in a low permeability reservoir is the fractal dimension. In this study, three different methods, each utilizing mercury intrusion porosimetry (MIP) data, were adopted to analyze the fractal dimensions and the fractal curves of sandstones from the no. 8 layer of the Xiashihezi Formation (He 8 member) in the Linxing block, dated from the Middle Permian. The morphological features of the fractal curves, the characteristics of the fractal dimensions and the theoretical differences between these three methods were also discussed. The results show that the fractal dimensions obtained by method I reflect the characteristics of the remaining pores that are not intruded by mercury, and they show that the involved pore scales are more comprehensive. While in methods II and III, both obtain the fractal dimensions of the pores intruded by mercury, the difference between them is in the selection of a simplified pore shape model, which results in the fractal dimensions differing by a value of 1 between them. No matter which method is adopted, the pore structures of tight sandstone reservoirs in the Linxing block exhibit fractal characteristics. However, the fractal dimensions obtained by method I are more suitable for describing the complexity and petrophysical properties of the tight sandstone pores in the He 8 member of the Linxing block. The fractal curves obtained by different methods are consistent to a certain extent in terms of morphological changes. Small pores (fractal characteristics, while large pores (>r max-point) are the critical factor affecting the seepage

  4. The Upper Cretaceous Ostravice Sandstone in the Polish sector of the Silesian Nappe, Outer Western Carpathians

    Directory of Open Access Journals (Sweden)

    Cieszkowski Marek

    2016-04-01

    Full Text Available The Ostravice Sandstone Member was identified and described as a lithostratigraphic unit in the Polish part of the Outer Carpathians. This division occurs in the lowermost part of the Godula Formation, is underlain by variegated deposits of the Mazák Formation or directly by the Barnasiówka and Lhoty formations, and overlain by the Czernichów Member of the Godula Formation. Domination by thick- and very thick-bedded sandstones, conglomeratic sandstones and conglomerates rich in calcareous clasts, mostly of the Štramberk-type limestones, is typical for the Ostravice Sandstone Member. These deposits are widespread between the Moravskoslezské Beskydy Mountains in the Czech Republic and the Ciężkowice Foothills in Poland. The documentation of the Ostravice Sandstone Member occurrence as well as the petrological, sedimentological features, and inventory of the carbonate clasts are presented here.

  5. Cathodoluminescence investigations on quartz cement in the sandstones of Khabour Formation from Iraqi Kurdistan Region, Northern Iraq

    DEFF Research Database (Denmark)

    Omer, Muhamed Fakhri; Friis, Henrik

    2014-01-01

    The Ordovician deltaic to shallow marine Khabour Formation in Northern Iraq consists mainly of sandstone with minor siltstone and interbedded shale. The sandstones are pervasively cemented by quartz that resulted in very little preserved primary porosity. Cathodoluminescence and petrographic stud...

  6. Evolution of pore space in sandstones in relation to diagenesis

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, G.

    1982-01-01

    Results are described from studying the collector properties of a bed of sandstones of Yan-10 at the oil field Malin of the Ordosskiy oil and gas basin. The bed is represented by ancient river sandstones of the Jurassic age occurring on eroded surface of the Triassic deposits (Yangan series) and covered with bed of coal deposits Yan-9. The following conclusions were drawn from the results of the studies. Evolution of the pore space actually is the process of gradual substitution of the primary pores by secondary; in this case decrease in porosity in the quartz sandstones occurs mainly because of depositing in the pores of authigenic minerals, and in the sandstones whose grains consist of minerals with lower mechanical strength, because of packing. Secondary porosity develops because of dissolving and kaolinization in the sandstones with high content of feldspars. This process is possibly associated with decarboxilation of organic matter of interlayers of coal and calcareous shales under the influence of increased temperature in the submersion process. Since it has been established that considerable influence on porosity comes from the mineralogical position of the sandstones controlled by the sources of formation, in order to reveal the zones for development of primary and secondary porosity, it is very important to reveal the sources of removal of detrital rocks. A study was also made of the influence of diagenesis on uniformity and texture of the sandstones (by the methods of curves of capillary pressure).

  7. Diagenetic evolution and its effect on reservoir-quality of fan delta sandstones during progressive burial:Evidence from the upper part of the fourth member of Shahejie formation, Bonan sag, Jiyang depression

    Institute of Scientific and Technical Information of China (English)

    马奔奔; 张少敏; 操应长; 贾艳聪; 王艳忠

    2015-01-01

    Petrographic analysis combined with various techniques, such as thin section identification, fluid inclusions, isotopic data, petro-physical property testing and oil testing results, was used to study diagenetic evolution and its effect on reservoir-quality of fan delta reservoirs of Es4s in the Bonan sag. The diagenesis is principally characterized by strong compaction, undercompaction, multi-phase of dissolution and cementation. Compaction played a more important role than cementation in destroying the primary porosity of the sandstones. The reservoirs have experienced complicated diagenetic environment evolution of “weak alkaline− acid−alkalinity−acid−weak alkalinity” and two-stage of hydrocarbon filling. The diagenetic sequences are summarized as “early compaction/early pyrite/gypsum/calcite/dolomite cementation→feldspar dissolution/the first stage of quartz overgrowth→ early hydrocarbon filling→quartz dissolution/anhydrite/Fe-carbonate cementation→Fe-carbonate dissolution/feldspar dissolution/ the second stage of quartz overgrowth→later hydrocarbon filling→later pyrite cementation. In the same diagenetic context, the diagenetic evolution processes that occurred in different sub/micro-facies during progressive burial have resulted in heterogeneous reservoir properties and oiliness. The braided channel reservoirs in fan delta plain are poorly sorted with high matrix contents. The physical properties decrease continually due to the principally strong compaction and weak dissolution. The present properties of braided channel reservoirs are extremely poor, which is evidenced by few oil layers developed in relatively shallow strata while dry layers entirely in deep. The reservoirs both in the underwater distributary channels and mouth bars are well sorted and have a strong ability to resist compaction. Abundant pores are developed in medium-deep strata because of modifications by two-stage of acidic dissolution and hydrocarbon filling. The

  8. Diagenesis Along Fractures in an Eolian Sandstone, Gale Crater, Mars

    Science.gov (United States)

    Ming, D. W.; Yen, A. S.; Rampe, E. B.; Grotzinger, J. P.; Blake, D. F.; Bristow, T. F.; Chipera, S. J.; Downs, R.; Morris, R. V.; Morrison, S. M.; Vaniman, D. T.; Gellert, R.; Sutter, B.; Treiman, A. H.

    2016-01-01

    The Mars Science Laboratory rover Curiosity has been exploring sedimentary deposits in Gale crater since August 2012. The rover has traversed up section through approx.100 m of sedimentary rocks deposited in fluvial, deltaic, lacustrine, and eolian environments (Bradbury group and overlying Mount Sharp group). The Stimson formation lies unconformable over a lacustrine mudstone at the base of the Mount Sharp group and has been interpreted to be a cross-bedded sandstone of lithified eolian dunes. Mineralogy of the unaltered Stimson sandstone consists of plagioclase feldspar, pyroxenes, and magnetite with minor abundances of hematite, and Ca-sulfates (anhydrite, bassanite). Unaltered sandstone has a composition similar to the average Mars crustal composition. Alteration "halos" occur adjacent to fractures in the Stimson. Fluids passing through these fractures have altered the chemistry and mineralogy of the sandstone. Silicon and S enrichments and depletions in Al, Fe, Mg, Na, K, Ni and Mn suggest aqueous alteration in an open hydrologic system. Mineralogy of the altered Stimson is dominated by Ca-sulfates, Si-rich X-ray amorphous materials along with plagioclase feldspar, magnetite, and pyroxenes, but less abundant in the altered compared to the unaltered Stimson sandstone and lower pyroxene/plagioclase feldspar. The mineralogy and geochemistry of the altered sandstone suggest a complicated history with several (many?) episodes of aqueous alteration under a variety of environmental conditions (e.g., acidic, alkaline).

  9. 徐家围子断陷登娄库组三段成岩模拟与致密砂岩储层类型预测%Diagenetic numerical modeling and tight sandstone reservoir types prediction of the Member 3 of the Denglouku Formation of the Xujiaweizi Fault Depression

    Institute of Scientific and Technical Information of China (English)

    程仲平; 孟元林; 田伟志; 孟凡晋; 王建伟; 徐赫; 潘雪梅; 王维安; 蒋学峰

    2011-01-01

    为了预测松辽盆地徐家围子断陷深层登娄库组三段致密砂岩储层的类型和质量,根据深层的勘探实践和储层分析化验资料,将碎屑岩的成岩作用进一步细化为早成岩阶段A期、B期,中成岩阶段A1亚期,A2亚期、B1亚期、B2亚期,晚成岩阶段A期和B期3个阶段8个(亚)期,其中处于晚成岩阶段A期和B期的致密砂岩储层已不能产出工业气流。孔隙度和渗透率的统计结果表明,徐家围子断陷致密砂岩储层的物性主要受沉积相和成岩作用的影响,不同的沉积相和成岩相组合形成了致密砂岩3种类型的储层(Ⅱ、Ⅲ、Ⅳ类)。通过模拟古地温、镜质组反射率、甾烷异构化、粘土矿物转化和自生石英含量随时间的变化规律,模拟了成岩演化史、预测了成岩阶段和成岩相的平面分布。综合考虑沉积相和成岩作用对储层物性的影响,应用成岩作用数值模拟技术,通过成岩相分析,结合沉积相的研究成果,预测了登三段致密砂岩各种类型储层的平面分布特征。目前已发现的工业气流井主要位于Ⅱ、Ⅲ类储层分布的范围内。Ⅳ类储层中未发现工业气流,该类致密砂岩储层主要分布在晚成岩阶段A期—B期或处于滨浅湖相。引起成岩作用差异的主要因素是埋深。%To predict the reservoir type and quality of the tight sandstones of the Member 3 of the Denglouku Formation in the deep horizons of the Xujiaweizi Fault Depression,Songliao Basin,the diageneses of clastic rocks are divided into the period A of early diagenetic stage,the period B of early diagenetic stage,the sub-period A1 of middle diagenetic stage,the sub-period A2 of middle diagenetic stage,the sub-period B1 of middle diagenetic stage,the sub-period B2 of middle diagenetic stage,the period A of late diagenetic stage and the period B of late diagenetic stage on the base of the exploration results of the deep horizons and the reservoir

  10. Sandstone Diagenesis at Gale Crater, Mars, As Observed By Curiosity

    Science.gov (United States)

    Siebach, K. L.; Grotzinger, J. P.; McLennan, S. M.; Hurowitz, J.; Kah, L. C.; Edgett, K. S.; Williams, R. M. E.; Wiens, R. C.; Schieber, J.

    2014-12-01

    The Mars Science Laboratory rover, Curiosity, has encountered a significant number of poorly-sorted and very well-lithified sandstones along its traverse on the floor of Gale Crater. We use images from the hand-lens imager (MAHLI) and elemental chemistry from the ChemCam laser-induced breakdown spectroscopy instrument (LIBS) and the alpha-particle x-ray spectrometer (APXS) to begin to constrain the diagenetic history of these sandstones, including lithification and possible later dissolution. Investigation of MAHLI images reveals that the sediments are poorly-sorted and show very low apparent porosity, generally less than ~5%. However, in some cases, such as the Gillespie Lake sandstone identified in Yellowknife Bay, this apparent porosity includes a significant fraction of void spaces larger than typical sediment grain sizes (~30% by number or 75% of void spaces by area). One possible explanation of these larger pits is that they represent recent removal of soft intraclasts by eolian abrasion. Another possibility is that later diagenetic fluids caused dissolution of more soluble grains, and production of secondary porosity. Investigation into the elemental chemistry of the sandstones has shown that they have a relatively unaltered basaltic bulk composition in spite of possessing a variety of secondary minerals and amorphous material, indicating isochemical diagenetic processes. The chemistry and mineralogy of the cement is not immediately evident based on the initial analyses; there is not a high percentage of salts or evaporative minerals that may easily cement near-surface sandstones. Furthermore, these sandstones lack textures and compositions consistent with pedogenic processes, such as calcrete, silcrete, or ferricrete. Instead, they may record burial and cementation at depth. Cement composition may be constrained through comparison to terrestrial basaltic sandstones, and studying chemical variations along ChemCam and APXS transects of the rocks.

  11. Diagenesis of low-permeability and tight sandstone gas reservoir and its effect on reservoir quality: taking the eighth member of Shihezi formation in Su 48 block, Sulige gas field, as an example%低渗透致密气藏成岩作用及对储层物性的影响——以苏里格气田苏48区块盒8段储层为例

    Institute of Scientific and Technical Information of China (English)

    庞振宇; 孙卫; 赵春龙; 马永平

    2012-01-01

    利用普通薄片、铸体薄片、X射线衍射、扫描电镜等资料,分析苏里格气田苏48区块盒8段低渗透储层岩石学特征、成岩作用和孔隙演化过程.研究表明:储集层砂岩类型以岩屑石英砂岩和石英砂岩为主,颗粒分选性中等-好,磨圆度较差,胶结类型以次生加大-孔隙式为主,少量孔隙式胶结.在成岩过程中,强烈的压实作用造成了初始孔隙度的大量丧失,损失率为69.09%,其次为胶结作用,损失率为25.16%.溶蚀作用则形成大量次生孔隙,增加了5.82%的孔隙度,大大改善了储层物性,为该区气藏的聚集提供了主要储集空间.%The characteristics of petrology, the diagenesis and porosity evolution in the eighth member of Shihezi formation in Su 48 block in Sulige gasfield were analyzed, using thin-sections, casting thin-sections, X-ray diffractions, scanning electron micrograph observations, etc. The results showed that both lithic quartz-sandstone and quartz sandstone are the essential components of reservoir sandstones. The sandstone is lithic quartz with middle to perfect sorting and poor psephicity. Cementation is mainly of secondary enlargement-pore and a less proportion of pore cementation. The impact of strong compaction during the early diagenesis was greatest and its porosity loss-rate was 69.09%, and the porosity loss-rate of of cementation was 25.16%. The dissolution of the reservoir sandstone improved the porosity by about 5.82%, which provided the main space for the accumulation of gas reservoirs.

  12. Homo- and heteropolynuclear Ni2+ and Cu2+ complexes of polytopic ligands, consisting of a tren unit substituted with three 12-membered tetraazamacrocycles.

    Science.gov (United States)

    Siegfried, Liselotte; McMahon, C Niamh; Baumeister, Jan; Neuburger, Markus; Kaden, Thomas A; Anandaram, Sreekanth; Palivan, Cornelia G

    2007-11-14

    Two new polytopic ligands L1 and L2 have been synthesized. They consist of a central tren unit to which three 1,4,7,10-tetraazacyclododecane rings are attached via an ethylene and a trimethylene bridge, respectively. The complexation properties of L1 and L2 towards Cu(2+) and Ni(2+) were studied by potentiometric pH titration, UV-Vis, EPR spectroscopy and kinetic techniques. As a comparison, the Cu(2+) and Ni(2+) complexes with L3 (1-(N-methyl-2-aminoethyl-1,4,7,10-tetraazacyclododecane)) were also investigated. The crystal structures of [CuL3H(H(2)O)](ClO(4))(3) and [NiL3Cl](ClO(4)) were solved and show that the side chain in its protonated form is not involved in coordination, whereas deprotonated it binds to the metal ion. The thermodynamically stable 3:1 complexes of L1 or L2 have a metal ion in the three macrocyclic units. However, when three equivalents of Cu(2+) are added to L1 or L2 the metal ion first binds to the tren unit and only then to the macrocycles. The kinetics of the different steps of complexation have been studied and a mechanism is proposed.

  13. The geometry and lithology of the Cima Sandstone Lentil: a paleoseep-bearing interbed in the Moreno Formation, central California

    Science.gov (United States)

    Wheatley, P. V.; Schwartz, H.

    2007-12-01

    The Cima Sandstone Lentil outcrops over a relatively small area on the western side of the San Joaquin Valley in central California. Here this unit can be found in the Panoche Hills in the northern portion of the field area and the Tumey Hills in the southern portion of the field area. The Cima Sandstone resides within the 800m Moreno Formation that spans the Maastrichtian to the Danian. The Moreno Formation comprises four members, which are the Dosados Member, the Tierra Loma Member, the Marca Shale Member, and the Dos Palos Shale Member (of which the Cima Sandstone is an interbed). The Cima Sandstone contains numerous large carbonate mounds, concretions, and pavements, indicating paleoseep activity. The Cima Sandstone has never been studied in detail, but recent interest in sandstone injectites as well as interest in paleoseeps has prompted us to examine this interbed more carefully. The Cima is an immature sandstone composed primarily of quartz along with small amounts of micas and feldspars as well as varying amounts of glauconite. These minerals are generally cemented by carbonate but, occasionally, iron oxide cement is present locally. Much variation exists within the Cima Sandstone Lentil and we seek to characterize and understand this variation. One of the most obvious sources of variability is the thickness of the unit itself. The thickness ranges from near 60m in the northern Panoche Hills to only 9m in the Tumey Hills. Induration also varies noticeably, from well cemented in the north, to unconsolidated in the south. Similarly, the sandstone is grain-supported and houses some depositional structures in the northern outcrops but becomes largely matrix-supported and lacking bedding in the southern outcrops. Preliminary data suggests that proximity to carbonate concretions, fluid conduits, and underlying injectites may have some influence over grain size and sorting.

  14. Quantitative simulation of porosity-evolution in the Member 8 sandstone reservoir of the Yanchang formation in Huanxian Oilfield, Ordos Basin%鄂尔多斯盆地环县地区长8段砂岩储层孔隙度演化定量模拟

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    Thin section analysis indicated that the diagenesis of the sandstone reservoir in the research area had mainly undergone the processes of compaction, cementation and dissolution. Combined with the mathe-matical statistics method, the methodology was based on an analysis of tight sandstone reservoir characteristics, controlling factors and a study of the burial history and diagenetic history of the study area. With current porosity as boundary constraint conditions, the geological time and burial depth as variables, the whole porosity evolution from initial burial until the present was divided into two independent processes: porosity decrease and porosity increase, for which two mathematical models were established respectively. The quantitative simulation result indicates that the whole porosity-evolution quantitative simulation was a piecewise function with four sections. That is, the porosity decrease model for the mechanical compaction and cementation stages served a continuous exponential function with the geological time and burial depth as the variables, and the secondary porosity increase was caused by organic acid dissolution within a temperature window of 80∼100◦C. Therefore, the dissolution phase was of a porosity increase model, which was a composite function of the depth, burial time and porosity decrease amount. After the dissolution phase, the porosity was in the phase of compaction and maintenance. Finally, through the exemplification, it was verified that the porosity-evolution quantitative simulation established by the present researcher is consistent with actual geological conditions and can be applied to porosity calculation of any stratum in the study area.%  在充分分析研究区长8段砂岩储层特征、主控因素及地层埋藏史和成岩史的基础上,应用数理统计方法,以现今孔隙度为约束条件,将孔隙度演化分为减小和增大两个过程,分别建立了鄂尔多斯盆地环县地区长8段砂

  15. Sequence stratigraphy of the marine and non-marine Upper Cretaceous Dakota Sandstone, San Juan Basin, USA

    Energy Technology Data Exchange (ETDEWEB)

    Johannessen, P.

    1994-12-31

    Late Cretaceous, middle Cenomanian, shallow marine and non-marine sandstones of the Dakota Sandstone have been studied in the western part of the Western Interior, San Juan Basin, New Mexico. 15-20 m thick sharp based, slightly coarsening upward shoreface sandstones characterize the eastern fully marine part of the San Juan Basin, while non-marine sediments dominate the western part of the basin. The aim of this paper is to carefully correlate key-surfaces from the thick shoreface sandstones towards the west into the non-marine succession, using sequence stratigraphic principles. The present paper will document an additional marine sandstone underlying the Cubero Tongue; the Oak Canyon Member. (au)

  16. Reservoir assessment of the Nubian sandstone reservoir in South Central Gulf of Suez, Egypt

    Science.gov (United States)

    El-Gendy, Nader; Barakat, Moataz; Abdallah, Hamed

    2017-05-01

    The Gulf of Suez is considered as one of the most important petroleum provinces in Egypt and contains the Saqqara and Edfu oil fields located in the South Central portion of the Gulf of Suez. The Nubian sandstone reservoir in the Gulf of Suez basin is well known for its great capability to store and produce large volumes of hydrocarbons. The Nubian sandstone overlies basement rocks throughout most of the Gulf of Suez region. It consists of a sequence of sandstones and shales of Paleozoic to Cretaceous age. The Nubian sandstone intersected in most wells has excellent reservoir characteristics. Its porosity is controlled by sedimentation style and diagenesis. The cementation materials are mainly kaolinite and quartz overgrowths. The permeability of the Nubian sandstone is mainly controlled by grain size, sorting, porosity and clay content especially kaolinite and decreases with increase of kaolinite. The permeability of the Nubian Sandstone is evaluated using the Nuclear Magnetic Resonance (NMR technology) and formation pressure data in addition to the conventional logs and the results were calibrated using core data. In this work, the Nubian sandstone was investigated and evaluated using complete suites of conventional and advanced logging techniques to understand its reservoir characteristics which have impact on economics of oil recovery. The Nubian reservoir has a complicated wettability nature which affects the petrophysical evaluation and reservoir productivity. So, understanding the reservoir wettability is very important for managing well performance, productivity and oil recovery.

  17. Attenuation of Landfill Leachate In Unsaturated Sandstone

    Science.gov (United States)

    Butler, A. P.; Brook, C.; Godley, A.; Lewin, K.; Young, C. P.

    feature of the sequences of porewater concentration profiles is the sharp leading front of the Cl plume. Thus indicating that very little solute dispersion appears to be occurring. This is probably to be due to the relatively uniform particle size of the sand matrix combined with the low moisture content, which has greatly constrained the available pore sizes in which flow occurs. A marked reduction in the mass of the chloride plume has been observed over the last 13 years. Analyses of core sample taken in 2000 show that the Cl profile has continued to lose mass and has now also separated into two peaks. The leading peak was located at a depth of 36 m below ground level (28 m below the base of the landfill) and in line with model predictions. The trailing peak was at a depth of 27 m bgl and was associated with a 0.3 m layer of marl and clay bands. Thus there is an indication that the changes in chloride mass are possibly due to the effects of heterogeneity, although other processes which could account for chloride removal from solution are also under consideration. The location of the TOC front up to 1992 was commensurate with that of Cl, indicating no effective retardation. This is consistent with the very low levels of organic carbon present in the sandstone. However, marked reductions in contaminant mass (substantially greater than those of Cl) have been observed. Analyses of volatile fatty acids has indicated a progressive breakdown of VFA components leading to simpler products so that by 1991 the dominant component was ethanoic acid (56% by mass). By 2000 the entire leading front of the TOC was absent. TOC was only found to be present at relatively low concentrations ( 100 mg.l-1) above the marl/clay band. Analyses of gas concentrations at the site have indicated that there has been a change in the redox potential in the volume of contaminated unsaturated sandstone below the waste cells during the last 10 years. With predominantly anaerobic conditions giving way to

  18. National uranium resource evaluation. Geology and recognition criteria for sandstone uranium deposits of the salt wash type, Colorado Plateau Province. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Thamm, J.K.; Kovschak, A.A. Jr.; Adams, S.S.

    1981-01-01

    The uranium-vanadium deposits of the Salt Wash Member of the Morrison Formation in the Colorado Plateau are similar to sandstone uranium deposits elsewhere in the USA. The differences between Salt Wash deposits and other sandstone uranium deposits are also significant. The Salt Wash deposits are unique among sandstone deposits in that they are dominantly vanadium deposits with accessory uranium. The Salt Wash ores generally occur entirely within reduced sandstone, without adjacent tongues of oxidized sandstone. They are more like the deposits of Grants, which similarly occur in reduced sandstones. Recent studies of the Grants deposits have identified alteration assemblages which are asymmetrically distributed about the deposits and provide a basis for a genetic model for those deposits. The alteration types recognized by Shawe in the Slick Rock district may provide similar constraints on ore formation when expanded to broader areas and more complete chemical analyses.

  19. Diagenesis of deep sandstone reservoirs and a quantitative model of porosity evolution: Taking the third member of Shahejie Formation in the Wendong Oilfield, Dongpu Sag, as an example%深层储集层成岩作用及孔隙度演化定量模型——以东濮凹陷文东油田沙三段储集层为例

    Institute of Scientific and Technical Information of China (English)

    王瑞飞; 沈平平; 赵良金

    2011-01-01

    The diagenesis and porosity evolution in the deep 3rd member of Shahejie Formation of the Wendong Oilfield was analyzed using thin-sections, casting thin-sections, X-ray diffractometry, scanning electron micrograph observations, and other data. Sandstone reservoirs are currently at the late diagenetic period. Pores consist of primary pores and the inter-granular dissolved and intra-granular dissolved pores of feldspar, debris and carbonate cements. Physical properties are mainly controlled by carbonate cementation and dissolution, and distribution of abnormally high fluid pressure. The evolution of porosity parameters shows that primary porosity is 36.75%, the porosity loss rate is 40.49% during the process of mechanic compaction, the porosity loss rate is 37.25% during the process of cementation and metasomasis, and the porosity increase rate is 17.88% during the process of dissolution. The proportion of primary porosity is 55.03%, and that of the secondary porosity is 44.97%. The error rate in the quantitative study of porosity is 0.96%, and the main influencing factor of the error rate is sorting coefficient of detrital rock (So).%利用普通薄片、铸体薄片、X射线衍射、扫描电镜等资料,分析东濮凹陷文东油田沙三段深层储集层砂岩成岩作用和孔隙演化过程.研究表明,储集层砂岩目前处于晚成岩阶段,储集层发育原生粒间孔隙和长石、岩屑、胶结物等不稳定组分的粒间溶孔、粒内溶孔.储集层物性分布受碳酸盐等的胶结、溶蚀及异常高压带分布的控制.孔隙度参数演化分析表明,储集层初始孔隙度为36.75%,压实过程孔隙度损失率为40.49%,胶结-交代过程孔隙度损失率为37.25%,后期溶蚀、溶解过程孔隙度增加率为17.88%.储集空间中原生孔隙占总孔隙的55.03%,次生孔隙占总孔隙的44.97%.孔隙度计算过程中误差率为0.96%,影响误差的主要因素为颗粒分选系数.

  20. Multidisciplinary studies on ancient sandstone quarries of Western Sardinia (Italy).

    Science.gov (United States)

    Grillo, Silvana Maria; Del Vais, Carla; Naitza, Stefano

    2013-04-01

    The ancient coastal quarries of Mediterranean are increasingly considered geosites of multidisciplinary relevance. They are sites of historical-archaeological interest that show ancient techniques of stone extraction; they are significant for cultural heritage conservation and restoration, as sources of the stones used in ancient buildings and monuments; they are sites of geological relevance, as often retain important stratigraphic sections; they are also useful markers of secular changes in the sea level. A multisciplinary study is in progress on the ancient quarries of the Sinis region (western Sardinia island), integrating archaeological, geological, minero-petrographical data. In Sardinia, coastal quarries have been established from Punic and Roman times. Many of them exploited Quaternary sediments along the southern and western coasts of the island. They consist of middle-late Pleistocene marine conglomerates and carbonate sandstones, and of coastal (aeolian) carbonate sandstones. Sandstone blocks of different sizes have been widely used in ancient cities for buildings, defensive works, harbours, etc. Three main areas of stone extraction (San Giovanni di Sinis, Punta Maimoni, Is Arutas) have been so far recognized in the Sinis. GIS-supported mapping and documentation of the sites includes their geology and stratigraphy, the extension and layout of the quarries, and an evaluation of volumes of extracted rocks. Documented archaeological evidences include ancient extraction fronts, spoil heaps, working areas, working traces in the old fronts, transport routes of blocks, and traces of loading facilities. The study is aimed at reconstructing the relationships of the quarries with the urban areas of Sinis, as the ancient Punic-Roman city of Tharros. Consequently, a minero-petrographical characterization (optical microscopy, XRD) is performed on sandstones sampled in each quarry, and in historical buildings in Tharros and other centres of the region (Cabras

  1. Pore evolution and gas accumulation in tight sandstone reservoir of Member 2 of Xujiahe Formation in Yuanba area of Sichuan, China%四川元坝地区须二段致密砂岩储层孔隙演化与天然气成藏

    Institute of Scientific and Technical Information of China (English)

    王威

    2012-01-01

    Based on the quantitative statistics of the clasties and matrixes in the reservoir and quantitative evolutional analysis of pores, and according to the homogeneous temperature of inclusions and buried history of the reservoir, this paper makes an approach to the pore evolution and the natural gas accumulation in the tight sandstone reservoir of Member 2 of Xujiahe Formation (T3x2) of Upper Triassic in the Yuanba area of Sichuan Basin. The dynamic recovery of the compacted history of the reservoir is achieved. In the early diagenetic stage, the porosity of the reservoir declined to 8. 7%, meanwhile, the tight reservoir formed. Following this? A scries of cementations made the primary pores decreasing. The anisotropy is heightened, too. It can be known that the gas filling time of T3x2 in the Yuanba area is in the middle diagenetic stage A when the reservoir was tightened. Totally, "first is the compaction of reservoirs, and second is natural gas accumulation". The gas moves by "piston type advancing" in the reservoir. So the gas concentration is controlled by hydrocarbon-generating intensity and high quality reservoirs. Therefore, the depressed area in the eastern of Yuanba can be regarded as a favorable area for gas exploration.%利用储层中不同碎屑颗粒、填隙物的定量统计和孔隙在压实作用下的定量演化分析以及储层中包裹体均一温度,结合储层埋藏史分析等方法,探讨了四川盆地元坝地区上三叠统须二段致密砂岩储层孔隙演化与天然气成藏的关系.早成岩阶段结束时,储层的孔隙度已经降至8.7%,致密储层业已形成,此后一系列的胶结作用导致原生孔隙进一步减少,非均质性强.而元坝地区须二段天然气大规模充注时间为中成岩A期,此时储层巳经致密,总体反映出“储层先致密,天然气后成藏”的特点,天然气在储层中以“活塞式推进”方式运移,气藏富集主要受源岩的生烃强度

  2. Rate type isotach compaction of consolidated sandstone

    NARCIS (Netherlands)

    Waal, J.A. de; Thienen-Visser, K. van; Pruiksma, J.P.

    2015-01-01

    Laboratory experiments on samples from a consolidated sandstone reservoir are presented that demonstrate rate type compaction behaviour similar to that observed on unconsolidated sands and soils. Such rate type behaviour can have large consequences for reservoir compaction, surface subsidence and

  3. Experimental strain analysis of Clarens Sandstone colonised by endolithic lichens

    Directory of Open Access Journals (Sweden)

    D. Wessels

    1995-09-01

    Full Text Available Endolithic lichens occur commonly on Clarens Sandstone in South Africa, where they significantly contribute to the weathering of sandstone by means of mechanical and chemical weathering processes. This preliminary investigation reports on the success- ful use of strain gauges in detecting strain differences between sandstone without epilithic lichens and sandstone colonised by the euendolithic lichen Lecidea aff. sarcogynoides Korb. Mechanical weathering, expressed as strain changes, in Clarens Sandstone was studied during the transition from relatively dry winter to wet summer conditions. Daily weathering of sandstone due to thermal expansion and contraction of colonised and uncolonised sandstone could be shown. Our results show that liquid water in sandstone enhances the mechanical weathering of uncolonised Clarens Sandstone while water in the gaseous phase enhances mechanical weathering of sandstone by euendolithic lichens.

  4. Genesis and identification of high gamma sandstone in the first member of Nantun formation of Wunan depression in Hailar Basin%海拉尔盆地乌南凹陷南一段高伽马砂岩成因与识别

    Institute of Scientific and Technical Information of China (English)

    于振锋; 程日辉; 赵小青; 孙凤贤; 许中杰; 沈艳杰

    2012-01-01

    In order to improve the accuracy of logging lithology identification of high natural gamma sandstone in Wunan depression in Hailar Basin, in terms of rock core and microscopic sections description and logging analysis, the causes and i-dentifieation of high gamma sandstones were discussed. The classification of the sandstone CNL values can provide a estimating under a certain porosity degree. The high natural gamma sandstones can be identified using deep lateral resistivity ( DLL), micro lateral resistivity logging ( RMLL) , DEN and AC. The research results show that the factors affecting these sandstones with high natural gamma are tuffaceous matter, clay, oil, feldspar and calcium. High natural gamma sandstones express high content of thorium or uranium from logging data. The tuffaceous matter leads to the enrichment of thorium, clay leads to the enrichment of uranium, thorium and potassium, oil leads to the enrichment of uranium, feldspar leads to the enrichment of potassium, and calcareous matter leads to the decrease of uranium content. The affecting factors of sandstone nature gamma ray are high tuffaceous matter, high feldspar and high clay ranging from edge to center of the depression.%为了提高海托尔盆地乌南凹陷高伽马砂岩测井岩性解释的准确性,采用岩心观察、显微镜下描述和测井曲线分析相结合的方法对高伽马砂岩的成因和识别方法进行探讨.对砂岩的补偿中子值进行分类以排除孔隙度对测井曲线的影响,再利用深侧向电阻率、微侧向电阻率和补偿密度交会识别高自然伽马砂岩.研究结果表明:影响砂岩自然伽马特征的因素有凝灰质、黏土、油、长石以及钙质;高自然伽马砂岩具有高钍或者高铀含量的特征;凝灰质导致钍富集,黏士导致铀、针和钾均富集,油导致铀富集,长石导致钾富集,钙质导致铀含量降低;从凹陷边缘至凹陷中央影响砂岩高自然伽马因素依次为高凝灰质含

  5. "Sydney sandstone": Heritage Stone from Australia

    Science.gov (United States)

    Cooper, Barry; Kramar, Sabina

    2014-05-01

    Sydney is Australia's oldest city being founded in 1788. The city was fortunate to be established on an extensive and a relatively undeformed layer of lithified quartz sandstone of Triassic age that has proved to be an ideal building stone. The stone has been long identified by geologists as the Hawkesbury Sandstone. On the other hand the term "Sydney sandstone" has also been widely used over a long period, even to the extent of being utilised as the title of published books, so its formal designation as a heritage stone will immediately formalise this term. The oldest international usage is believed to be its use in the construction of the Stone Store at Kerikeri, New Zealand (1832-1836). In the late 19th century, public buildings such as hospitals, court houses as well as the prominent Sydney Town Hall, Sydney General Post Office, Art Gallery of New South Wales, State Library of New South Wales as well as numerous schools, churches, office building buildings, University, hotels, houses, retaining walls were all constructed using Sydney sandstone. Innumerable sculptures utilising the gold-coloured stone also embellished the city ranging from decorative friezes and capitals on building to significant monuments. Also in the late 19th and early 20th century, Sydney sandstone was used for major construction in most other major Australian cities especially Melbourne, Adelaide and Brisbane to the extent that complaints were expressed that suitable local stone materials were being neglected. Quarrying of Sydney sandstone continues today. In 2000 it was recorded noted that there were 33 significant operating Sydney sandstone quarries including aggregate and dimension stone operations. In addition sandstone continues to be sourced today from construction sites across the city area. Today major dimension stone producers (eg Gosford Quarries) sell Sydney sandstone not only into the Sydney market but also on national and international markets as cladding and paving products

  6. Improvement of attenuation functions of a clayey sandstone for landfill leachate containment by bentonite addition.

    Science.gov (United States)

    Ruiz, Ana I; Fernández, Raúl; Sánchez Jiménez, Nicanor; Rodríguez Rastrero, Manuel; Regadío, Mercedes; de Soto, Isabel S; Cuevas, Jaime

    2012-03-01

    Enhanced sand-clay mixtures have been prepared by using a sandstone arkosic material and have been evaluated for consideration as landfill liners. A lab-scale test was carried out under controlled conditions with different amended natural sandstones whereby leachate was passed through the compacted mixtures. The compacted samples consisted of siliceous sand (quartz-feldspar sand separated from the arkose sandstone) and clay (purified clay from arkose sandstone and two commercial bentonites) materials that were mixed in different proportions. The separation of mineral materials from a common and abundant natural source, for soil protection purposes, is proposed as an economic and environmentally efficient practice. The liner qualities were compared for their mineralogical, physicochemical and major ions transport and adsorption properties. Although all samples fulfilled hydraulic conductivity requirements, the addition of bentonite to arkose sandstone was determined to be an effective strategy to decrease the permeability of the soil and to improve the pollutants retention. The clay materials from arkose sandstone also contributed to pollutant retention by a significant improvement of the cation exchange capacity of the bulk material. However, the mixtures prepared with clay materials from the arkose, exhibited a slight increase of hydraulic conductivity. This effect has to be further evaluated. Copyright © 2011 Elsevier B.V. All rights reserved.

  7. Facies architecture of the Bluejacket Sandstone in the Eufaula Lake area, Oklahoma: Implications for the reservoir characterization of the Bartlesville Sandstone

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Liangmiao; Yang, Kexian [Univ. of Tulsa, OK (United States)

    1997-08-01

    Outcrop studies of the Bluejacket Sandstone (Middle Pennsylvanian) provide significant insights to reservoir architecture of the subsurface equivalent Bartlesville Sandstone. Quarry walls and road cuts in the Lake Eufaula area offer excellent exposures for detailed facies architectural investigations using high-precision surveying, photo mosaics. Directional minipermeameter measurements are being conducted. Subsurface studies include conventional logs, borehole image log, and core data. Reservoir architectures are reconstructed in four hierarchical levels: multi-storey sandstone, i.e. discrete genetic intervals; individual discrete genetic interval; facies within a discrete genetic interval; and lateral accretion bar deposits. In both outcrop and subsurface, the Bluejacket (Bartlesville) Sandstone comprises two distinctive architectures: a lower braided fluvial and an upper meandering fluvial. Braided fluvial deposits are typically 30 to 80 ft thick, and are laterally persistent filling an incised valley wider than the largest producing fields. The lower contact is irregular with local relief of 50 ft. The braided-fluvial deposits consist of 100-400-ft wide, 5-15-ft thick channel-fill elements. Each channel-fill interval is limited laterally by an erosional contact or overbank deposits, and is separated vertically by discontinuous mudstones or highly concentrated mudstone interclast lag conglomerates. Low-angle parallel-stratified or trough cross-stratified medium- to coarse-grained sandstones volumetrically dominate. This section has a blocky well log profile. Meandering fluvial deposits are typically 100 to 150 ft thick and comprise multiple discrete genetic intervals.

  8. Simulation of channel sandstone architecture in an incised valley

    Energy Technology Data Exchange (ETDEWEB)

    Frykman, P.; Johannessen, P.; Andsbjerg, J.

    1998-12-31

    The present report describes a geostatistical modelling study that is aimed at reflecting the architecture of the channel sandstones in an incised valley fill. The example used for this study is a part of the Middle Jurassic sandy succession of the Bryne Formation in the Danish central Graben. The succession consists mainly of fluvial sediments in the lower part, overlain by tidal influenced sediments, which again is overlain by shallow marine sediments. The modelling study has been performed on a sequence of incised valley sediments in the upper part of the Bryne Formation overlying fluvial sediments. (au) EFP-96. 19 refs.

  9. Dispersion analysis of velocity and attenuation in Berea sandstone

    Science.gov (United States)

    Winkler, Kenneth W.

    1985-07-01

    Ultrasonic velocity and attenuation measurements were made on dry, brine- and oil-saturated Berea sandstone and fused glass beads. The results for fused glass beads are consistent with the predictions of Biot theory. They indicate that as predicted, the Biot absorption/dispersion mechanism shifts to higher frequencies as the fluid viscosity increases. Similar data for Berea sandstone are not consistent with Biot theory, since observed velocities are generally higher than predicted. Using the Biot theory, we calculate low- and high-frequency velocities for the liquid-saturated samples. "Biot dispersion" is then defined as the percent difference between the low- and high-frequency limits. "Apparent dispersion" is defined as the percent difference between the measured ultrasonic velocity and the low-frequency Biot limit. Comparison of these two measures of dispersion gives insight into the presence of a non-Biot absorption/dispersion mechanism. Whenever the apparent dispersion is larger than the Biot dispersion, the extra dispersion is interpreted as being caused by a local flow relaxation. To be consistent with attenuation data, this relaxation must be distributed over at least five to six decades in frequency.

  10. Impact Metamorphism of Sandstones at Amguid Crater, Algeria

    Science.gov (United States)

    Sahoui, R.; Belhai, D.

    2016-08-01

    Amguid is a 450 m diameter sample crater; it is emplaced in Lower Devonian sandstones.We have carried out a petrographic study in order to investigate shock effects recorded in these sandstones and define shock stages in Amguid.

  11. Salamanca sandstone: a good GHSR not suitable for all construction purposes.

    Science.gov (United States)

    Pereira, Dolores; Blanco, Jose Antonio; Nespereira, Jose

    2016-04-01

    Salamanca sandstone, which in fact is an opal-cemented formation of sandstones and conglomerates, was used in the construction of many historical buildings of Salamanca old city, as well as other places nearby. Salamanca is recognized as World Heritage site since 1988, precisely because the homogeneous architecture and the use of local natural resources, as the Salamanca sandstone, the Villamayor sandstone and some local granites. The reason for using the sedimentary stone was the easy access of the resource, as the city is built on top of the Salamanca sandstone Formation, a late Cretaceous-early Palaeocene deposit. This formation consists of siliciclastic successions that were deposited in braided fluvial systems. These materials are derived from a deeply weathered Variscan basement showing ferruginous alteration that adds an aesthetic value to the global view of the natural stone. However, after several centuries, the stone has started to show serious problems due to water absorption, mainly in those places where it was used as basement of the buildings. Restoration of historical buildings should consider the use of the same original material when replacement is requested. But when this original material has been demonstrated to be not appropriate for long-term constructions, a matching and preferable natural stone should be used for replacement. There is such possibility in Salamanca and this has not have to mean the disregard of the Salamanca sandstone for other uses. The natural stone has been used for interior use and for sculpture with quality results. We present the Salamanca sandstone as a possible candidate to be taken into account as GHSR, supported by complete characterization and use recommendation.

  12. Fractures and stresses in Bone Spring sandstones

    Energy Technology Data Exchange (ETDEWEB)

    Lorenz, J.C.; Warpinski, N.R.; Sattler, A.R.; Northrop, D.A.

    1990-09-01

    This project is a collaboration between Sandia National Laboratories and Harvey E. Yates Company being conducted under the auspices of the Oil Recovery Technology Partnership. The project seeks to apply perspectives related to the effects of natural fractures, stress, and sedimentology to the simulation and production of low-permeability gas reservoirs to low-permeability oil reservoirs as typified by the Bone Spring sandstones of the Permian Basin, southeast New Mexico. This report presents the results and analysis obtained in 1989 from 233 ft of oriented core, comprehensive suite of logs, various in situ stress measurements, and detailed well tests conducted in conjunction with the drilling of two development wells. Natural fractures were observed in core and logs in the interbed carbonates, but there was no direct evidence of fractures in the sandstones. However, production tests of the sandstones indicated permeabilities and behavior typical of a dual porosity reservoir. A general northeast trend for the maximum principal horizontal stress was observed in an elastic strain recovery measurements and in strikes of drilling-induced fractures; this direction is subparallel to the principal fracture trend observed in the interbed carbonates. Many of the results presented are believed to be new information for the Bone Spring sandstones. 57 figs., 18 tabs.

  13. Densification Modes of Sandstone Reservoir in the 8th Member of the Lower Shihezi Formation,Permian,in Su-6 Area of Sulige Gas Field,Ordos Basin%鄂尔多斯盆地苏里格气田苏6区块二叠系下石盒子组8段砂岩储层致密成因模式

    Institute of Scientific and Technical Information of China (English)

    毕明威; 刘金; 陈世悦; 周兆华; 郑国强; 张满郎; 高立祥; 钱爱华; 谷江锐; 石石

    2015-01-01

    Densification modes of tight sandstone reservoir of the 8th Member of Lower Shihezi Formation, Permian,in Su -6 Area of the Sulige Gas Field,Ordos Basin,are quantitatively analysised by means of slice identification,scan electron microscope,electron probe micro -analysis and energy spectrum,homogenization temperatures and raman microprobe research of fluid inclusions.The results are as follows:(1 )Densification process can be divided into the following stages,compaction during early diagenesis and the 1st stage siliceous cementation→—the 2nd stage siliceous cementat ion and grain -coating chlorite→—the 1st stage dissolution (hydrocarbon charge →—) compaction during late diagenesis and the 3rd stage siliceous cementation (densification of reservoir )→—the 2nd stage dissolution and the 4th stage sil iceous cementation→—cementation and replacement of chlorite→—cementation and replacement of carbonate.(2)Densification modes of reservoir can be divided into three types:densification of medium -coarse grained litharenite by strong compaction;densification of medium -coarse grained lithic quartzarenite by strong siliceous cementation and medium to strong compaction;densification of fine grained (feldspathic ) litharenite by strong compaction and medium to strong siliceous cementation.(3)The main reasons for densification of reservoir are compaction and siliceous cementation.And the 2nd stage dissolution under enclosed environment has less ascension of porosity,which is another important reason for densification.(4)The two types of medium -coarse grained sandstones are densification after hydrocarbon charge,which experience injection of organic acid and make dissolved pore to be the major storage space.Fine grained (feldspathic)litharenite is densification before hydrocarbon charge,which experience weak dissolution. (5)Difference of densification modes lead to the porosity,permeability ,correlation of permeability and porosity of medium -coarse

  14. Interface Consistency

    DEFF Research Database (Denmark)

    Staunstrup, Jørgen

    1998-01-01

    This paper proposes that Interface Consistency is an important issue for the development of modular designs. Byproviding a precise specification of component interfaces it becomes possible to check that separately developedcomponents use a common interface in a coherent matter thus avoiding a very...... significant source of design errors. Awide range of interface specifications are possible, the simplest form is a syntactical check of parameter types.However, today it is possible to do more sophisticated forms involving semantic checks....

  15. Appalachian Basin Low-Permeability Sandstone Reservoir Characterizations

    Energy Technology Data Exchange (ETDEWEB)

    Ray Boswell; Susan Pool; Skip Pratt; David Matchen

    1993-04-30

    A preliminary assessment of Appalachian basin natural gas reservoirs designated as 'tight sands' by the Federal Energy Regulatory Commission (FERC) suggests that greater than 90% of the 'tight sand' resource occurs within two groups of genetically-related units; (1) the Lower Silurian Medina interval, and (2) the Upper Devonian-Lower Mississippian Acadian clastic wedge. These intervals were targeted for detailed study with the goal of producing geologic reservoir characterization data sets compatible with the Tight Gas Analysis System (TGAS: ICF Resources, Inc.) reservoir simulator. The first phase of the study, completed in September, 1991, addressed the Medina reservoirs. The second phase, concerned with the Acadian clastic wedge, was completed in October, 1992. This report is a combined and updated version of the reports submitted in association with those efforts. The Medina interval consists of numerous interfingering fluvial/deltaic sandstones that produce oil and natural gas along an arcuate belt that stretches from eastern Kentucky to western New York. Geophysical well logs from 433 wells were examined in order to determine the geologic characteristics of six separate reservoir-bearing intervals. The Acadian clastic wedge is a thick, highly-lenticular package of interfingering fluvial-deltaic sandstones, siltstones, and shales. Geologic analyses of more than 800 wells resulted in a geologic/engineering characterization of seven separate stratigraphic intervals. For both study areas, well log and other data were analyzed to determine regional reservoir distribution, reservoir thickness, lithology, porosity, water saturation, pressure and temperature. These data were mapped, evaluated, and compiled into various TGAS data sets that reflect estimates of original gas-in-place, remaining reserves, and 'tight' reserves. The maps and data produced represent the first basin-wide geologic characterization for either interval. This report

  16. Diagenetic history of Early Cambrian sandstones, at Gazouieyeh outcrop, Central Iran

    Directory of Open Access Journals (Sweden)

    Mohammadreza Ghotbi

    2015-01-01

    Full Text Available The siliciclastic Dahu Strata (Early Cambrian, in the Central Iran, 280 metres thick, in the Gazouieyeh area, rests with an erosional surface on Protrozoic-Early Cambrian sedimentary rocks (Dezu Series. This strata disconformably overlain by Middle Cambrian-Late Cambrian marine carbonate rockse (Kouh-Banan Formation. Based on field and Laboratory studies, 3 association facies, shale-sandstone and conglomerate have been identified. Mainly, sandstones are rich in quartz, feldspars, and rarely contain rock fragments (metamorphic and sedimentary. The sandstones have a wide compositional range from quartzarenite to arkose, feldspathic litharenite and rarely litharenite (chertarenite. According to plots of feldspar garins, total quartzose grains, and total unstable lithic fragments, they were derived from craton interior, transitional continental, and recycled orogen sources. The Dahu sandstones experienced diagenetic events that included compaction and pressure solution, cementation (mostly by silica, carbonate, Fe-oxide, clay and rarely by barite, grain fracturing, alteration of unstable grains, dissolution and replacement. Based on petrological and geochemical studies, we interpreted the diagenetic history for the Dahu sandstones, which consists of early, deep burial and late stages. The above results are based on surface studies, but it might be changed during increasing the depth.

  17. Solid consistency

    Science.gov (United States)

    Bordin, Lorenzo; Creminelli, Paolo; Mirbabayi, Mehrdad; Noreña, Jorge

    2017-03-01

    We argue that isotropic scalar fluctuations in solid inflation are adiabatic in the super-horizon limit. During the solid phase this adiabatic mode has peculiar features: constant energy-density slices and comoving slices do not coincide, and their curvatures, parameterized respectively by ζ and Script R, both evolve in time. The existence of this adiabatic mode implies that Maldacena's squeezed limit consistency relation holds after angular average over the long mode. The correlation functions of a long-wavelength spherical scalar mode with several short scalar or tensor modes is fixed by the scaling behavior of the correlators of short modes, independently of the solid inflation action or dynamics of reheating.

  18. Characteristics and controlling factors of movable fluid in deep-buried high-pressure and low-permeability sandstone reservoirs:A case study of middle section of 3rd member of Shahejie Formation in Wendong Oil Field, Dongpu Sag%深层高压低渗砂岩储层可动流体赋存特征及控制因素--以东濮凹陷文东沙三中油藏为例

    Institute of Scientific and Technical Information of China (English)

    王瑞飞; 齐宏新; 吕新华; 国殿斌

    2014-01-01

    利用核磁共振技术,对东濮凹陷文东沙三中深层高压低渗砂岩储层样品进行测试分析,通过可动流体百分数、可动流体孔隙度参数分析了可动流体的赋存特征及控制因素。研究结果表明,不同离心力的T2谱形态表现为4种类型,T2截止值与物性呈正相关关系。可动流体含量低且其分布具有较强的非均质性,渗透率越高,主流喉道半径越大,可动流体参数值越大,可动流体参数与渗透率的相关关系越好;渗透率越低,可动流体参数衰减越快。储层微观孔隙结构是可动流体赋存的主要控制因素。应用喉道半径区间分布表征微观孔隙结构对可动流体分布的控制,效果较好。物性越好,大喉道控制的可动流体量越高。%The samples of the deep-buried high-pressure and low-permeability sandstone reservoirs in the middle section of the 3rd member of the Shahejie Formation in the Wendong Oil Field of the Dongpu Sag were tested with nuclear magnetic resonance technique. The characteristics and controlling factors of movable fluid were analyzed with movable fluid percentage and porosity. The results have shown that the T2 pattern of the samples displays 4 modes, and the T2 cutoff value is positively correlated with porosity. The movable fluid content is relatively low and the heterogeneity is intense. The higher the permeability is, the wider is the main throat radius. The relation between the movable fluid parameter and the permeability gets better with the increase of permeability. The mova-ble fluid parameter gets higher attenuation velocity with the decrease of permeability and has more sensitivity to the changes of permeability. The micro-pore structure determines the existing state of fluid in deep-buried high-pressure and low-permeability sandstone reservoir. Applying main throat radius, the micro-pore structure control-ling movable fluid was token, which has achieved good results

  19. Microstructural changes of sandstone specimens during CO2 injection

    Science.gov (United States)

    Park, J. H.; Son, J.; Oh, M.; Park, H. D.

    2014-12-01

    Carbon dioxide capture and storage (CCS) is a technology to isolate CO2 from atmosphere, by capturing it from sources, transporting it to injection area, and injecting it into suitable geological formation, ocean, or mineral carbonation plant. Geological storage of carbon dioxide is the most effective and economical method, and until now a lot of demonstration projects were carried out successfully such as Sleipner, Weyburn, and In Salah. In Republic of Korea, small-scale CO2 injection demonstration project is now under investigation in offshore Pohang Basin with sandstone reservoir and the mudstone caprock. When CO2 is injected in target site, the rock around injection well can be deteriorated because of extreme change of temperature and pressure. In this study supercritical CO2 was injected in sandstone specimen and the initiation and propagation of fracture inside the specimens were observed using X-ray computed tomography (CT). X-ray CT method is a computer technology to observe inner density of target object in three dimensional image. Because of its non-destructivity and high resolution, it is suitable for consistent observation of the same specimen. Porosity and permeability of the specimens were measured using X-ray CT images and both of them were increased after injection. P- and S-wave velocity were also measured to assess the change of mechanical property and both of them were decreased after injection because of growth of inner fractures. The data from this research can be used as input data of CCS site.

  20. Experimental Analysis of Sandstone and Travertine

    Directory of Open Access Journals (Sweden)

    T. Doležel

    2004-01-01

    Full Text Available Sandstone and travertine are sedimentary rocks. The former is clastic, while the latter is sourced by chemical precipitation from hot springs. Their applications in civil engineering structures are mostly influenced by the ability to carry compression loading. A three-point bending experiment is usually used to determine material characteristics. However it does not correspond very well to applicatiosn in structures. For this reason we used a uniaxial compression test to obtain the modulus of elasticity and the stress-strain diagram. To obtain detailed information about the crystalline structure of sandstone and travertine a microscopic analysis wascarried out, using optical microscopy and an EDAX multichannel spectrometer for elementary microanalysis. 

  1. Performance of Different Acids on Sandstone Formations

    Directory of Open Access Journals (Sweden)

    M. A. Zaman

    2013-12-01

    Full Text Available Stimulation of sandstone formations is a challenging task, which involves several chemicals and physical interactions of the acid with the formation. Some of these reactions may result in formation damage. Mud acid has been successfully used to stimulate sandstone reservoirs for a number of years. It is a mixture of hydrofluoric (HF and hydrochloric (HCl acids designed to dissolve clays and siliceous fines accumulated in the near-wellbore region. Matrix acidizing may also be used to increase formation permeability in undamaged wells. The change may be up to 50% to 100% with the mud acid. For any acidizing process, the selection of acid (Formulation and Concentration and the design (Pre-flush, Main Acid, After-flush is very important. Different researchers are using different combinations of acids with different concentrations to get the best results for acidization. Mainly the common practice is combination of Hydrochloric Acid – Hydrofluoric with Concentration (3% HF – 12% HCl. This paper presents the results of a laboratory investigation of Orthophosphoric acid instead of hydrochloric acid in one combination and the second combination is Fluoboric and formic acid and the third one is formic and hydrofluoric acid. The results are compared with the mud acid and the results calculated are porosity, permeability, and FESEM Analysis and Strength tests. All of these new combinations shows that these have the potential to be used as acidizing acids on sandstone formations.

  2. Hydrofacies In Sandstones. Evidence For Feedback Between Sandstone Lithofacies and Permeability Development

    Science.gov (United States)

    Bloomfield, J. P.; Newell, A.; Moreau, M.

    In order to enhance our ability to develop effective numerical models of flow and con- taminant transport in the Permo-Triassic sandstone aquifer of the UK, relationships between lithofacies, rock mass characteristics (such as porosity and pore-throat size distribution), and permeability have been investigated through a series of case studies. Flow in the Permo-Triassic sandstones is primarily through the matrix. Permeability distribution is principally a function of the pore-throat size distribution and there is a relatively weak correlation with primary sedimentary lithofacies. It is observed that matrix permeability data broadly fall into two, discontinuous, sub-populations above and below about 1 mD. It is proposed that modification of primary sedimentary litho- facies by circulation of groundwater is the main control on the development of these two permeability sub-populations or hydrofacies. Identification of these two hydrofa- cies has significant implications for numerical modelling of the sandstones.

  3. Depositional sequence stratigraphy and architecture of the cretaceous ferron sandstone: Implications for coal and coalbed methane resources - A field excursion

    Science.gov (United States)

    Garrison, J.R.; Van Den, Bergh; Barker, C.E.; Tabet, D.E.

    1997-01-01

    This Field Excursion will visit outcrops of the fluvial-deltaic Upper Cretaceous (Turonian) Ferron Sandstone Member of the Mancos Shale, known as the Last Chance delta or Upper Ferron Sandstone. This field guide and the field stops will outline the architecture and depositional sequence stratigraphy of the Upper Ferron Sandstone clastic wedge and explore the stratigraphic positions and compositions of major coal zones. The implications of the architecture and stratigraphy of the Ferron fluvial-deltaic complex for coal and coalbed methane resources will be discussed. Early works suggested that the southwesterly derived deltaic deposits of the the upper Ferron Sandstone clastic wedge were a Type-2 third-order depositional sequence, informally called the Ferron Sequence. These works suggested that the Ferron Sequence is separated by a type-2 sequence boundary from the underlying 3rd-order Hyatti Sequence, which has its sediment source from the northwest. Within the 3rd-order depositional sequence, the deltaic events of the Ferron clastic wedge, recognized as parasequence sets, appear to be stacked into progradational, aggradational, and retrogradational patterns reflecting a generally decreasing sediment supply during an overall slow sea-level rise. The architecture of both near-marine facies and non-marine fluvial facies exhibit well defined trends in response to this decrease in available sediment. Recent studies have concluded that, unless coincident with a depositional sequence boundary, regionally extensive coal zones occur at the tops of the parasequence sets within the Ferron clastic wedge. These coal zones consist of coal seams and their laterally equivalent fissile carbonaceous shales, mudstones, and siltstones, paleosols, and flood plain mudstones. Although the compositions of coal zones vary along depositional dip, the presence of these laterally extensive stratigraphic horizons, above parasequence sets, provides a means of correlating and defining the tops

  4. Origin of gray-green sandstone in ore bed of sandstone type uranium deposit in north Ordos Basin

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Dongsheng sandstone-type uranium deposit is located in the northern part of Ordos Basin, occurring in the transitional zones between gray-green and gray sandstones of Jurassic Zhiluo Formation. Sandstones in oxidized zone of the ore bed look gray-green, being of unique signature and different from one of ordinary inter-layered oxidation zone of sandstone-type uranium deposits. The character and origin of gray-green sandstones are systematically studied through their petrology, mineralogy and geochemistry. It is pointed out that this color of sandstones is originated from secondary oil-gas reduction processes after paleo-oxidation, being due to acicular-leaf chlorite covering surfaces of the sandstone grains. To find out the origin of gray-green sandstone and recognize paleo-oxidation zones in the ore bed are of not only theoretical significance for understanding metallogenesis of this kind of sandstone-type uranium deposit, but also very importantly practical significance for prospecting for similar kind of sandstone-type uranium deposit.

  5. An Effective Acid Combination for Enhanced Properties and Corrosion Control of Acidizing Sandstone Formation

    Science.gov (United States)

    Umer Shafiq, Mian; Khaled Ben Mahmud, Hisham

    2016-03-01

    To fulfill the demand of the world energy, more technologies to enhance the recovery of oil production are being developed. Sandstone acidizing has been introduced and it acts as one of the important means to increase oil and gas production. Sandstone acidizing operation generally uses acids, which create or enlarge the flow channels of formation around the wellbore. In sandstone matrix acidizing, acids are injected into the formation at a pressure below the formation fracturing pressure, in which the injected acids react with mineral particles that may restrict the flow of hydrocarbons. Most common combination is Hydrofluoric Acid - Hydrochloric with concentration (3% HF - 12% HCl) known as mud acid. But there are some problems associated with the use of mud acid i.e., corrosion, precipitation. In this paper several new combinations of acids were experimentally screened to identify the most effective combination. The combinations used consist of fluoboric, phosphoric, formic and hydrofluoric acids. Cores were allowed to react with these combinations and results are compared with the mud acid. The parameters, which are analyzed, are Improved Permeability Ratio, strength and mineralogy. The analysis showed that the new acid combination has the potential to be used in sandstone acidizing.

  6. The sandstone's chromatic alteration of the florentine cultural heritage

    Science.gov (United States)

    Vettori, S.; Pecchioni, E.; Cantisani, E.; Ricci, M.; Fratini, F.; Garzonio, C. A.

    2012-04-01

    Pietra Serena is one of the materials more used in Florentine architecture. It is a sandstone that outcrops in the hills north of the city in the municipality of Fiesole and it has been employed mainly for ornamental purposes. This litotype belongs to the the Macigno Formation (Oligocene Upper- Miocene Lower) which consists of beds of turbiditic sandstones separated by pelitic levels which are the finest components of each single turbidity layer. Petrographically, Pietra Serena can be defined as a medium-coarse-grained greywacke made of quartz, feldspars, micas, fragments of metamorphic and magmatic rocks. The clayey matrix is quite abundant, mainly composed by illite, kaolinite and chlorite-vermiculite (present only in some quarries). It is well known that the processes of decay of the sandstones are related to the type of matrix, the amount of cement, the kind of clay minerals and to the pore size distribution, which lead to water infiltrations, swelling of the clay minerals, separation of the clayey matrix, with resulting exfoliation and peeling of the stone artefacts. Pietra Serena has a bluish-grey colour in fresh cut, but many times it is easily oxidized acquiring an ochraceous-reddish brown colour on buildings. Such changes in colour, appear to be due in part to the oxidation of iron, proceeding very quickly from the surface to the inside, though the cohesion is not affected. It is possible to hypothesize that the chromatic changes not necessarily involve a progressive state of alteration of the artefact, but they may often to represents a natural patina acquired with the time. Nevertheless it is necessary to remember that the oxidized layer and its hardness could also be the result of treatments performed in the past. In Florence, several monuments and buildings are affected by such phenomenon, in particular it is possible to note an intense and diffuse reddish colouring on the Pietra Serena utilized for columns and for façade's decorations. In this work

  7. Downslope coarsening in aeolian grainflows of the Navajo Sandstone

    Science.gov (United States)

    Loope, David B.; Elder, James F.; Sweeney, Mark R.

    2012-07-01

    Downslope coarsening in grainflows has been observed on present-day dunes and generated in labs, but few previous studies have examined vertical sorting in ancient aeolian grainflows. We studied the grainflow strata of the Jurassic Navajo Sandstone in the southern Utah portion of its outcrop belt from Zion National Park (west) to Coyote Buttes and The Dive (east). At each study site, thick sets of grainflow-dominated cross-strata that were deposited by large transverse dunes comprise the bulk of the Navajo Sandstone. We studied three stratigraphic columns, one per site, composed almost exclusively of aeolian cross-strata. For each column, samples were obtained from one grainflow stratum in each consecutive set of the column, for a total of 139 samples from thirty-two sets of cross-strata. To investigate grading perpendicular to bedding within individual grainflows, we collected fourteen samples from four superimposed grainflow strata at The Dive. Samples were analyzed with a Malvern Mastersizer 2000 laser diffraction particle analyser. The median grain size of grainflow samples ranges from fine sand (164 μm) to coarse sand (617 μm). Using Folk and Ward criteria, samples are well-sorted to moderately-well-sorted. All but one of the twenty-eight sets showed at least slight downslope coarsening, but in general, downslope coarsening was not as well-developed or as consistent as that reported in laboratory subaqueous grainflows. Because coarse sand should be quickly sequestered within preserved cross-strata when bedforms climb, grain-size studies may help to test hypotheses for the stacking of sets of cross-strata.

  8. Microbial Penetration through Nutrient-Saturated Berea Sandstone.

    Science.gov (United States)

    Jenneman, G E; McInerney, M J; Knapp, R M

    1985-08-01

    Penetration times and penetration rates for a motile Bacillus strain growing in nutrient-saturated Berea sandstone cores were determined. The rate of penetration was essentially independent of permeabilities above 100 mdarcys and rapidly declined for permeabilities below 100 mdarcys. It was found that these penetration rates could be grouped into two statistically distinct classes consisting of rates for permeabilities above 100 mdarcys and rates for those below 100 mdarcys. Instantaneous penetration rates were found to be zero order with respect to core length for cores with permeabilities above 100 mdarcys and first order with respect to core length for cores with permeabilities below 100 mdarcys. The maximum observed penetration rate was 0.47 cm . h, and the slowest was 0.06 cm . h; however, these rates may be underestimates of the true penetration rate, since the observed rates included the time required for growth in the flask as well as the core. The relationship of penetration time to the square of the length of the core suggested that cells penetrated high-permeability cores as a band and low-permeability cores in a diffuse fashion. The motile Enterobacter aerogenes strain penetrated Berea sandstone cores three to eight times faster than did the nonmotile Klebsiella pneumoniae strain when cores of comparable length and permeability were used. A penetration mechanism based entirely on motility predicted penetration times that were in agreement with the observed penetration times for motile strains. The fact that nonmotile strains penetrated the cores suggested that filamentous or unrestricted growth, or both, may also be important.

  9. Age of the Bedford Shale, Berea Sandstone, and Sunbury Shale in the Appalachian and Michigan basins, Pennsylvania, Ohio, and Michigan

    Science.gov (United States)

    De Witt, Wallace

    1970-01-01

    The suggestion by Sanford (1967, p. 994) that the Bedford Shale, Berea Sandstone, and Sunbury Shale of the Michigan basin are of Late Devonian age because these strata contain Hymenozonotriletes lepidophytus Kedo is invalid for these formations in the Appalachian basin, the area of their type localities. Endosporites lacunosus Winslow, a synonym of Hymenozonotriletes lepidophytus Kedo, occurs in upper Chautauqua (Upper Devonian) rocks through much of the Kinderhook (Lower Mississippian) strata in Ohio. The Sunbury Shale, the Sunbury Member of the Orangeville Shale in part of northern Ohio, contains a Siplionodella fauna which clearly demonstrates the Kinderhook age of the unit. The basal strata of the Bedford Shale contain Spathoffnathodus anteposlcornis which suggests a very Late Devonian or very Early Mississippian age for this part of the Bedford. Except for the basal fossil zone, most of the Bedford Shale and the younger Berea Sandstone overlie the Murrysville sand, which along the Allegheny Front in central Pennsylvania contains an Adiantites flora of Early Mississippian (Kinderhook) age. The presence of Adiantites in the Murrysville sand indicates that most of the Bedford Shale and all the Berea Sandstone are of Early Mississippian age. Lithostratigraphic evidence suggests that the Berea Sandstone of Ohio may be a temporal equivalent of the basal Beckville Member of the Pocono Formation of the Anthracite region of Pennsylvania. The clearly demonstrable Kinderhook age of the Sunbury, Berea, and most of the Bedford in the Appalachian basin strongly indicates a similar age for the same units in the Michigan basin.

  10. Mechanism of Solid Bitumen in Silurian Sandstones of Tarim Basin

    Institute of Scientific and Technical Information of China (English)

    Zhang Jinglian; Zhu Bingquan

    1997-01-01

    @@ There are a large amount of solid bitumen within Silurian sandstones in Tabei, Tazhong, Kalpin uprifts of the Tarim Basin. Petroleum geochemists are interested in the super giant fossil oil pool. Unfortunately,some key questions have not been solved, such as: what generated the bitumen? When did the bitumen generate and when did the bitumen accumulated in the sandstones?

  11. Multiple stages of aqueous alteration along fractures in mudstone and sandstone strata in Gale Crater, Mars

    Science.gov (United States)

    Yen, A. S.; Ming, D. W.; Vaniman, D. T.; Gellert, R.; Blake, D. F.; Morris, R. V.; Morrison, S. M.; Bristow, T. F.; Chipera, S. J.; Edgett, K. S.; Treiman, A. H.; Clark, B. C.; Downs, R. T.; Farmer, J. D.; Grotzinger, J. P.; Rampe, E. B.; Schmidt, M. E.; Sutter, B.; Thompson, L. M.

    2017-08-01

    The Mars rover Curiosity in Gale crater conducted the first-ever direct chemical and mineralogical comparisons of samples that have clear parent (unaltered) and daughter (altered) relationships. The mineralogy and chemistry of samples within and adjacent to alteration halos in a sandstone formation were established by the Chemistry and Mineralogy (CheMin) X-ray diffraction (XRD) instrument and the Alpha Particle X-ray Spectrometer (APXS), respectively. The Stimson formation sandstones unconformably overlie the Murray mudstone formation and represent the youngest stratigraphic unit explored by Curiosity to date. Aqueous alteration of the parent sandstone resulted in a loss of half of the original crystalline mineral phases and a three-fold increase in X-ray amorphous material. Aqueous fluids extensively leached Mg, Al, Mn, Fe, Ni, Zn and other elements from the parent material, decreased the pyroxene to feldspar ratio by a factor of two, introduced Ca and mixed-cation sulfates, and both passively and actively enriched the silica content. Leaching of Mg, Al, Mn, Fe, Ni and Zn and enrichment of Si and S are also observed in alteration halos in the underlying mudstone. These observations are consistent with infiltration of subsurface fluids, initially acidic and then alkaline, propagating along fractures crosscutting the Stimson sandstone and Murray mudstone. The geochemistry and mineralogy suggest a complicated diagenetic history with multiple stages of aqueous alteration under a variety of environmental conditions (e.g. both low and moderate pH). The formation of these alteration halos post-dates lithification of the sandstones and mudstones and represents one of the youngest hydrogeologic events presently known to have occurred in Gale crater.

  12. Brittle and compaction creep in porous sandstone

    Science.gov (United States)

    Heap, Michael; Brantut, Nicolas; Baud, Patrick; Meredith, Philip

    2015-04-01

    Strain localisation in the Earth's crust occurs at all scales, from the fracture of grains at the microscale to crustal-scale faulting. Over the last fifty years, laboratory rock deformation studies have exposed the variety of deformation mechanisms and failure modes of rock. Broadly speaking, rock failure can be described as either dilatant (brittle) or compactive. While dilatant failure in porous sandstones is manifest as shear fracturing, their failure in the compactant regime can be characterised by either distributed cataclastic flow or the formation of localised compaction bands. To better understand the time-dependency of strain localisation (shear fracturing and compaction band growth), we performed triaxial deformation experiments on water-saturated Bleurswiller sandstone (porosity = 24%) under a constant stress (creep) in the dilatant and compactive regimes, with particular focus on time-dependent compaction band formation in the compactive regime. Our experiments show that inelastic strain accumulates at a constant stress in the brittle and compactive regimes leading to the development of shear fractures and compaction bands, respectively. While creep in the dilatant regime is characterised by an increase in porosity and, ultimately, an acceleration in axial strain to shear failure (as observed in previous studies), compaction creep is characterised by a reduction in porosity and a gradual deceleration in axial strain. The overall deceleration in axial strain, AE activity, and porosity change during creep compaction is punctuated by excursions interpreted as the formation of compaction bands. The growth rate of compaction bands formed during creep is lower as the applied differential stress, and hence background creep strain rate, is decreased, although the inelastic strain required for a compaction band remains constant over strain rates spanning several orders of magnitude. We find that, despite the large differences in strain rate and growth rate

  13. Subsurface sandstone mapping by combination of GPR and ERT method

    Institute of Scientific and Technical Information of China (English)

    YOU Zhixin

    2016-01-01

    It is important to know the shape and distribution of sandstone bodies in the subsurface when forma-tion and migration of a dune model are determined.The information plays a significant role in identification of the continental oil and gas accumulation.In this study,the combination of ground penetrating radar (GPR) and electrical resistivity tomography method (ERT)is used in mapping the distribution of sandstone bodies in Yanchang Formation.Six GPR profiles and seven ERT profiles are used to analysis.GPR data show clear re-flections from the top interface of sandstones.ERT data show a continuous high resistivity anomaly correspon-ding to the sandstone body.Combined the reconstructed 3D images by GPR and ERT,the spatial distribution of sandstone bodies is described.

  14. Effect of temperature on sandstone permeability

    DEFF Research Database (Denmark)

    Rosenbrand, Esther; Kjøller, Claus

    assumptions would be required in order to estimate sandstone permeability based on the Kozeny equation. An effective specific surface area per pore volume for permeability was estimated by using image analysis and pore size distributions as from nuclear magnetic resonance (NMR) transverse relaxation data...... be determined based on the Klinkenberg (1941) procedure, which accounts for effects on permeability of gas slip on the fluid-solid interface by means of several permeability measurements with different pore pressures. A comparison between the equivalent pore sizes as estimated using the Kozeny equation...... at 80°C than at 20°C; at 80°C the main effect might be due to an alteration of pore fluid rheology, whereas at 20°C particles might be filtered in pore constrictions. DLVO theory (Derjaguin and Landau (1941); Verwey and Overbeek (1948)) was used to compare effects of temperature and salinity on surface...

  15. Dilatant hardening of fluid-saturated sandstone

    Science.gov (United States)

    Makhnenko, Roman Y.; Labuz, Joseph F.

    2015-02-01

    The presence of pore fluid in rock affects both the elastic and inelastic deformation processes, yet laboratory testing is typically performed on dry material even though in situ the rock is often saturated. Techniques were developed for testing fluid-saturated porous rock under the limiting conditions of drained, undrained, and unjacketed response. Confined compression experiments, both conventional triaxial and plane strain, were performed on water-saturated Berea sandstone to investigate poroelastic and inelastic behavior. Measured drained response was used to calibrate an elasto-plastic constitutive model that predicts undrained inelastic deformation. The experimental data show good agreement with the model: dilatant hardening in undrained triaxial and plane strain compression tests under constant mean stress was predicted and observed.

  16. Experimental measurements of the SP response to concentration and temperature gradients in sandstones with application to subsurface geophysical monitoring

    Science.gov (United States)

    Leinov, E.; Jackson, M. D.

    2014-09-01

    Exclusion-diffusion potentials arising from temperature gradients are widely neglected in self-potential (SP) surveys, despite the ubiquitous presence of temperature gradients in subsurface settings such as volcanoes and hot springs, geothermal fields, and oil reservoirs during production via water or steam injection. Likewise, with the exception of borehole SP logging, exclusion-diffusion potentials arising from concentration gradients are also neglected or, at best, it is assumed that the diffusion potential dominates. To better interpret these SP sources requires well-constrained measurements of the various coupling terms. We report measurements of thermoelectric and electrochemical exclusion-diffusion potentials across sandstones saturated with NaCl brine and find that electrode effects can dominate the measured voltage. After correcting for these, we find that Hittorf transport numbers are the same within experimental error regardless of whether ion transport occurs in response to temperature or concentration gradients over the range of NaCl concentration investigated that is typical of natural systems. Diffusion potentials dominate only if the pore throat radius is more than approximately 4000 times larger than the diffuse layer thickness. In fine-grained sandstones with small pore throat diameter, this condition is likely to be met only if the saturating brine is of relatively high salinity; thus, in many cases of interest to earth scientists, exclusion-diffusion potentials will comprise significant contributions from both ionic diffusion through, and ionic exclusion from, the pore space of the rock. However, in coarse-grained sandstones, or sandstones saturated with high-salinity brine, exclusion-diffusion potentials can be described using end-member models in which ionic exclusion is neglected. Exclusion-diffusion potentials in sandstones depend upon pore size and salinity in a complex way: they may be positive, negative, or zero depending upon sandstone

  17. Discussion on origin of clay minerals in outcropped sandstone from Lower Cretaceous Chengzihe Formation and Muling Formation in Jixi Basin

    Institute of Scientific and Technical Information of China (English)

    LIU Jianying; LIU Li; QU Xiyu

    2009-01-01

    Clay minerals in the outcropped sandstone from Lower Cretaceous Chengzihe Formation and Muling Formation in Jixi Basin were analyzed by X-ray diffraction. The results show that the clay minerals mainly consist of illite, kaollinite and illite/smectite, which can be divided into two types: kaolinite- and illite/smectite types. The outcropped sandstone occurred in middle diagenetic stage-A on the basis of the clay mineral composition. The development factor of the formation of kaolinite type clay mineral is caused mainly by the organic acid from the coal-bearing formation and mudstone during the diagenesis process in Lower Cretaceous Chengzihe Formation and Muling Formation in the Jixi Basin. The weak hydrodynamic force of sedimentary facies made the sandstone leaching condition poor, which is the reason forming the aggregation of clay minerals of the illite/smectite-and illite types.

  18. Ichnology of an upper carboniferous fluvio-estuarine paleovalley: The tonganoxie sandstone, buildex quarry, eastern Kansas, USA

    Science.gov (United States)

    Buatois, L.A.; Mangano, M.G.; Maples, C.G.; Lanier, Wendy E.

    1998-01-01

    Tidal rhythmites of the Tonganoxie Sandstone Member (Stranger Formation, Douglas Group) at Buildex Quarry, eastern Kansas, contain a relatively diverse ichnofauna. The assemblage includes arthropod locomotion (Dendroidichnites irregulare, Diplichnites gouldi type A and B, Diplopodichnus biformis, Kouphichnium isp., Mirandaichnium famatinense, and Stiaria intermedia), resting (Tonganoxichnus buildexensis) and feeding traces (Stiallia pilosa, Tonganoxichnus ottawensis); grazing traces (Gordia indianaensis, Helminthoidichnites tenuis, Helminthopsis hieroglyphica); feeding structures (Circulichnis montanus, Treptichnus bifurcus, Treptichnus pollardi, irregular networks), fish traces (Undichna britannica, Undichna simplicitas), tetrapod trackways, and root traces. The taxonomy of some of these ichnotaxa is briefly reviewed and emended diagnoses for Gordia indianaensis and Helminthoidichnites tenuis are proposed. Additionally, the combined name Dendroidichnites irregulare is proposed for nested chevron trackways. Traces previously regarded as produced by isopods are reinterpreted as myriapod trackways (D. gouldi type B). Trackways formerly interpreted as limulid crawling and swimming traces are assigned herein to Kouphichnium isp and Dendroidichnites irregulare, respectively. Taphonomic analysis suggests that most grazing and feeding traces were formed before the arthropod trackways and resting traces. Grazing/feeding traces were formed in a soft, probably submerged substrate. Conversely, the majority of trackways and resting traces probably were produced subaerially in a firmer, dewatered and desiccated sediment. The Buildex Quarry ichnofauna records the activity of a terrestrial and freshwater biota. The presence of this assemblage in tidal rhythmites is consistent with deposition on tidal flats in the most proximal zone of the inner estuary, between the maximum landward limit of tidal currents and the salinity limit further towards the sea.

  19. Heat flow characterization and baseline of sandstone using infra-red thermography

    Science.gov (United States)

    Ibrahim, Y.; Padmanabhan, E.; Ano, A. B.; Ismail, W.

    2016-11-01

    Infra-red thermography was applied to sandstone to characterize and obtain a baseline or a reference thermal image for sandstone. The sample was imaged at room temperature and then heated and imaged again at different time intervals. The thermal images and the optical gradient obtained were analyzed, calibrated, and equated to actual-temperature measured geothermal gradient under controlled heat flux. Heat flow propagation is not consistent in the first time intervals (below 25 minutes). However, after that, the difference in temperature in the distal part and the proximal parts to the heat source almost remained constant. In general, the heat flow could fit to a linear model that is directly proportional to time. The results can be useful when applied to borehole thermal imaging, as well as in thermal conductivity and geothermal gradient determination.

  20. A two scale analysis of tight sandstones

    Science.gov (United States)

    Adler, P. M.; Davy, C. A.; Song, Y.; Troadec, D.; Hauss, G.; Skoczylas, F.

    2015-12-01

    Tight sandstones have a low porosity and a very small permeability K. Available models for K do not compare well with measurements. These sandstones are made of SiO_2 grains, with a typical size of several hundreds of micron. These grains are separated by a network of micro-cracks, with sizes ranging between microns down to tens of nm. Therefore, the structure can be schematized by Voronoi polyhedra separated by plane and permeable polygonal micro-cracks. Our goal is to estimate K based on a two scale analysis and to compare the results to measurements. For a particular sample [2], local measurements on several scales include FIB/SEM [3], CMT and 2D SEM. FIB/SEM is selected because the peak pore size given by Mercury Intrusion Porosimetry is of 350nm. FIB/SEM imaging (with 50 nm voxel size) identifies an individual crack of 180nm average opening, whereas CMT provides a connected porosity (individual crack) for 60 nm voxel size, of 4 micron average opening. Numerical modelling is performed by combining the micro-crack network scale (given by 2D SEM) and the 3D micro-crack scale (given by either FIB/SEM or CMT). Estimates of the micro-crack density are derived from 2D SEM trace maps by counting the intersections with scanlines, the surface density of traces, and the number of fracture intersections. K is deduced by using a semi empirical formula valid for identical, isotropic and uniformly distributed fractures [1]. This value is proportional to the micro-crack transmissivity sigma. Sigma is determined by solving the Stokes equation in the micro-cracks measured by FIB/SEM or CMT. K is obtained by combining the two previous results. Good correlation with measured values on centimetric plugs is found when using sigma from CMT data. The results are discussed and further research is proposed. [1] Adler et al, Fractured porous media, Oxford Univ. Press, 2012. [2] Duan et al, Int. J. Rock Mech. Mining Sci., 65, p75, 2014. [3] Song et al, Marine and Petroleum Eng., 65, p63

  1. Optical Image Analysis Applied to Pore Network Quantification of Sandstones Under Experimental CO2 Injection

    Science.gov (United States)

    Berrezueta, E.; González, L.; Ordóñez, B.; Luquot, L.; Quintana, L.; Gallastegui, G.; Martínez, R.; Olaya, P.; Breitner, D.

    2015-12-01

    This research aims to propose a protocol for pore network quantification in sandstones applying the Optical Image Analysis (OIA) procedure, which guarantees the measurement reproducibility and its reliability. Two geological formations of sandstone, located in Spain and potentially suitable for CO2 sequestration, were selected for this study: a) the Cretaceous Utrillas unit, at the base of the Cenozoic Duero Basin and b) a Triassic unit at the base of the Cenozoic Guadalquivir Basin. Sandstone samples were studied before and after the CO2 experimental injection using Optical and scanning electronic microscopy (SEM), while the quantification of petrographic changes was done with OIA. The first phase of the rersearch consisted on a detailed mineralogical and petrographic study of the sandstones (before and after CO2-injection), for which we observed thin sections. Later, the methodological and experimental processes of the investigation were focused on i) adjustment and calibration of OIA tools; ii) data acquisition protocol based on image capture with different polarization conditions (synchronized movement of polarizers), using 7 images of the same mineral scene (6 in crossed polarizer and 1 in parallel polarizer); and iii) automated identification and segmentation of pore in 2D mineral images, generating applications by executable macros. Finally, once the procedure protocols had been, the compiled data was interpreted through an automated approach and the qualitative petrography was carried out. The quantification of changes in the pore network through OIA (porosity increase ≈ 2.5%) has allowed corroborate the descriptions obtained by SEM and microscopic techniques, which consisted in an increase in the porosity when CO2 treatment occurs. Automated-image identification and quantification of minerals, pores and textures together with petrographic analysis can be applied to improve pore system characterization in sedimentary rocks. This research offers numerical

  2. Refuge Management Plan: Sandstone Unit Rice Lake National Wildlife Refuge

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Part I of this management plan for the Sandstone Unit of Rice Lake NWR summarizes background information on the location, history, environment, resources,...

  3. Size effect of sandstone after high temperature under uniaxial compression

    Institute of Scientific and Technical Information of China (English)

    SU Hai-jian; JING Hong-wen; MAO Xian-biao; ZHAO Hong-hui; YIN Qian; WANG Chen

    2015-01-01

    Uniaxial compression tests on sandstone samples with five different sizes after high temperature processes were performed in order to investigate the size effect and its evolution. The test results show that the density, longitudinal wave velocity, peak strength, average modulus and secant modulus of sandstone decrease with the increase of temperature, however, peak strain increases gradually. With the increase of ratio of height to diameter, peak strength of sandstone decreases, which has an obvious size effect. A new theoretical model of size effect of sandstone material considering the influence of temperature is put forward, and with the increase of temperature, the size effect is more apparent. The threshold decreases gradually with the increase of temperature, and the deviations of the experimental values and the theoretical values are between 0.44% and 6.06%, which shows quite a credibility of the theoretical model.

  4. Study on the cutting plane friction law of sandstone

    Institute of Scientific and Technical Information of China (English)

    ZHAI Ying-da (翟英达); KANG Li-xun(康立勋)

    2003-01-01

    The friction characteristics of rock damage plane have important impact on the stability of block structure formed after the stratum is broken. The mechanics properties of rock damage plane are described by parameters such as roughness coefficient, wall compress strength and basic friction angle. These three coefficients for fine grain sandstone and medium-granular sandstone and grit sandstone are test. The friction stress is researched at the condition of different normal compressive stress acting on the tension damage plane. The friction law of tension damage plane of sandstone abided by is summed up. This law will provide scientific basis for block structure stability judging in basic roof stratum and roof pressure intensity calculating.

  5. Sandstone petrofacies in the northwestern sector of the Iberian Basin

    OpenAIRE

    Arribas, J.; Ochoa, M; R Mas; Arribas, Mª E.; González-Acebrón, L.

    2007-01-01

    [EN] During the most active rifting stages in the northwestern sector of the Iberian Basin (Cameros Basin and Aragonese Branch of the Iberian Range), thick sequences of continental clastic deposits were generated. Sandstone records from Rift cycle 1 (Permo-Triassic) and Rift cycle 2 (Late Jurassic-Early Cretaceous) show similarities in composition. Based on the most recent data, this paper describes sandstone petrofacies developed during both rifting periods. Six petrofacies can be d...

  6. Sandstone petrofacies in the northwestern sector of the Iberian Basin

    OpenAIRE

    Arribas Mocoroa, José; Ochoa, M; Mas Mayoral, José Ramón; Arribas Mocoroa, María Eugenia; González-Acebrón, L.

    2007-01-01

    During the most active rifting stages in the northwestern sector of the Iberian Basin (Cameros Basin and Aragonese Branch of the Iberian Range), thick sequences of continental clastic deposits were generated. Sandstone records from Rift cycle 1 (Permo-Triassic) and Rift cycle 2 (Late Jurassic-Early Cretaceous) show similarities in composition. Based on the most recent data, this paper describes sandstone petrofacies developed during both rifting periods. Six petrofacies can be distinguishe...

  7. Micropore Structure Representation of Sandstone in Petroleum Reservoirs Using an Atomic Force Microscope

    Institute of Scientific and Technical Information of China (English)

    BAI Yong-Qiang; ZHU Xing; WU Jun-Zheng; BAI Wen-Guang

    2011-01-01

    @@ The pore structure of sandstone in an oil reservoir is investigated using atomic force microscopy(AFM).At nanoscale resolution,AFM images of sandstone show us the fine structure.The real height data of images display the three-dimensional space structure of sandstone effectively.The three-dimensional analysis results show that the AFM images of sandstone have unique characteristics that,like fingerprints,can identify different structural properties of sandstones.The results demonstrate that AFM is an effective method used to represent original sandstone in petroleum reservoirs,and may help geologists to appreciate the sandstone in oil reservoirs fully.

  8. Key Elements Controlling Oil Accumulation within the Tight Sandstones

    Institute of Scientific and Technical Information of China (English)

    Haiyan Hu; Zhiping Zeng; Jianzhang Liu

    2015-01-01

    Tight oil sandstone reservoirs with low porosity and permeability, which are an uncon-ventional petroleum resource, have been discovered in the Jurassic intervals of the central Junggar Ba-sin, the northwestern China. To reveal the accumulation mechanism, a relatively comprehensive re-search was conducted, including oil-source correlation, porosity evolution, and hydrocarbon charging history. The results show that crude oil of these tight sandstone reservoirs were mainly from Permian source rocks with some contribution from Jurassic source rocks. The reservoirs were buried at shallow depth (5%). In contrast, the sandstone reservoir had already become tight and did not provide available space to ac-cumulate oil due to severe compaction and cementation when hydrocarbon from Jurassic source rock filled, evidenced by low GOI values (<5%). Therefore, reservoir porosity controls the oil accumulation within tight sandstone. Whether tight sandstone reservoirs accumulate oil depends on the reservoir quality when hydrocarbons charge. Before the exploration of tight oil sandstone reservoirs, it should be required to investigate the relationship between oil charging history and porosity evolution to reduce the exploration risk and figure out the available targets.

  9. Deformation bands in porous sandstones their microstructure and petrophysical properties

    Energy Technology Data Exchange (ETDEWEB)

    Torabi, Anita

    2007-12-15

    Deformation bands are commonly thin tabular zones of crushed or reorganized grains that form in highly porous rocks and sediments. Unlike a fault, typically the slip is negligible in deformation bands. In this dissertation the microstructure and petrophysical properties of deformation bands have been investigated through microscopy and numerical analysis of experimental and natural examples. The experimental work consists of a series of ring-shear experiments performed on porous sand at 5 and 20 MPa normal stresses and followed by microscopic examination of thin sections from the sheared samples. The results of the ring-shear experiments and comparison of them to natural deformation bands reveals that burial depth (level of normal stress in the experiments) and the amount of shear displacement during deformation are the two significant factors influencing the mode in which grains break and the type of shear zone that forms. Two end-member types of experimental shear zones were identified: (a) Shear zones with diffuse boundaries, which formed at low levels of normal stress and/or shear displacement; and (b) Shear zones with sharp boundaries, which formed at higher levels of normal stress and/or shear displacement. Our interpretation is that with increasing burial depth (approximately more than one kilometer, simulated in the experiments by higher levels of normal stress), the predominant mode of grain fracturing changes from flaking to splitting; which facilitates the formation of sharp-boundary shear zones. This change to grain splitting increases the power law dimension of the grain size distribution (D is about 1.5 in sharp boundary shear zones). Based on our observations, initial grain size has no influence in the deformation behavior of the sand at 5 MPa normal stresses. A new type of cataclastic deformation band is described through outcrop and microscopic studies; here termed a 'slipped deformation band'. Whereas previously reported cataclastic

  10. Deformation bands in porous sandstones their microstructure and petrophysical properties

    Energy Technology Data Exchange (ETDEWEB)

    Torabi, Anita

    2007-12-15

    Deformation bands are commonly thin tabular zones of crushed or reorganized grains that form in highly porous rocks and sediments. Unlike a fault, typically the slip is negligible in deformation bands. In this dissertation the microstructure and petrophysical properties of deformation bands have been investigated through microscopy and numerical analysis of experimental and natural examples. The experimental work consists of a series of ring-shear experiments performed on porous sand at 5 and 20 MPa normal stresses and followed by microscopic examination of thin sections from the sheared samples. The results of the ring-shear experiments and comparison of them to natural deformation bands reveals that burial depth (level of normal stress in the experiments) and the amount of shear displacement during deformation are the two significant factors influencing the mode in which grains break and the type of shear zone that forms. Two end-member types of experimental shear zones were identified: (a) Shear zones with diffuse boundaries, which formed at low levels of normal stress and/or shear displacement; and (b) Shear zones with sharp boundaries, which formed at higher levels of normal stress and/or shear displacement. Our interpretation is that with increasing burial depth (approximately more than one kilometer, simulated in the experiments by higher levels of normal stress), the predominant mode of grain fracturing changes from flaking to splitting; which facilitates the formation of sharp-boundary shear zones. This change to grain splitting increases the power law dimension of the grain size distribution (D is about 1.5 in sharp boundary shear zones). Based on our observations, initial grain size has no influence in the deformation behavior of the sand at 5 MPa normal stresses. A new type of cataclastic deformation band is described through outcrop and microscopic studies; here termed a 'slipped deformation band'. Whereas previously reported cataclastic

  11. Capillarity and wetting of carbon dioxide and brine during drainage in Berea sandstone at reservoir conditions

    Science.gov (United States)

    Al-Menhali, Ali; Niu, Ben; Krevor, Samuel

    2015-10-01

    The wettability of CO2-brine-rock systems will have a major impact on the management of carbon sequestration in subsurface geological formations. Recent contact angle measurement studies have reported sensitivity in wetting behavior of this system to pressure, temperature, and brine salinity. We report observations of the impact of reservoir conditions on the capillary pressure characteristic curve and relative permeability of a single Berea sandstone during drainage—CO2 displacing brine—through effects on the wetting state. Eight reservoir condition drainage capillary pressure characteristic curves were measured using CO2 and brine in a single fired Berea sandstone at pressures (5-20 MPa), temperatures (25-50°C), and ionic strengths (0-5 mol kg-1 NaCl). A ninth measurement using a N2-water system provided a benchmark for capillarity with a strongly water wet system. The capillary pressure curves from each of the tests were found to be similar to the N2-water curve when scaled by the interfacial tension. Reservoir conditions were not found to have a significant impact on the capillary strength of the CO2-brine system during drainage through a variation in the wetting state. Two steady-state relative permeability measurements with CO2 and brine and one with N2 and brine similarly show little variation between conditions, consistent with the observation that the CO2-brine-sandstone system is water wetting and multiphase flow properties invariant across a wide range of reservoir conditions.

  12. Mineral Sequestration of Carbon Dixoide in a Sandstone-Shale System

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Tianfu; Apps, John A.; Pruess, Karsten

    2004-07-09

    A conceptual model of CO2 injection in bedded sandstone-shale sequences has been developed using hydrogeologic properties and mineral compositions commonly encountered in Gulf Coast sediments. Numerical simulations were performed with the reactive fluid flow and geochemical transport code TOUGHREACT to analyze mass transfer between sandstone and shale layers and CO2 immobilization through carbonate precipitation. Results indicate that most CO2 sequestration occurs in the sandstone. The major CO2 trapping minerals are dawsonite and ankerite. The CO2 mineral-trapping capacity after 100,000 years reaches about 90 kg per cubic meter of the medium. The CO2 trapping capacity depends on primary mineral composition. Precipitation of siderite and ankerite requires Fe+2 supplied mainly by chlorite and some by hematite dissolution and reduction. Precipitation of dawsonite requires Na+ provided by oligoclase dissolution. The initial abundance of chlorite and oligoclase therefore affects the CO2 mineral trapping capacity. The sequestration time required depends on the kinetic rate of mineral dissolution and precipitation. Dawsonite reaction kinetics is not well understood, and sensitivity regarding the precipitation rate was examined. The addition of CO2 as secondary carbonates results in decreased porosity. The leaching of chemical constituents from the interior of the shale causes slightly increased porosity. The limited information currently available for the mineralogy of natural high-pressure CO2 gas reservoirs is also generally consistent with our simulation. The ''numerical experiments'' give a detailed understanding of the dynamic evolution of a sandstone-shale geochemical system.

  13. Anatomy of an ancient aeolian sandstone on Mars: the Stimson formation, Gale crater, Mars

    Science.gov (United States)

    Gupta, Sanjeev; Banham, Steven; Rubin, David; Watkins, Jessica; Sumner, Dawn; Grotzinger, John P.; Lewis, Kevin; Edgett, Kenneth S.; Edgar, Lauren; Stack, Kathryn; Day, McKenzie; Ewing, Ryan; Lapotre, Mathieu

    2016-10-01

    Since landing in 2012, the Mars Science Laboratory's (MSL) rover Curiosity has traversed the plains and foothills of Aeolis Mons (informally known as Mt. Sharp) investigating the environments preserved in the stratigraphic record of Gale crater. Recently, the Curiosity team has been investigating the Stimson formation, a sandstone exhibiting abundant crossbedding that drapes the underlying Murray formation mudstones. The contact between the Stimson and underlying Murray formation exhibits several meters relief over several 100 m hundred metres where encountered thus far. The Stimson is observed to onlap onto this contact, indicating that accumulating Stimson sandstones unconformably onlapped or buried local palaeotopography.Facies and architectural elements observed within the Stimson are interpreted to represent deposition within an ancient dune field. The Stimson formation is typically composed of decimeter-scale and meter-scale crossbedded sandstones, (exhibiting wind-ripple lamination and well rounded particles up to granule size). Architectural elements are visible in outcrops oriented perpendicular to the regional northwest dip. These consist of undulating surfaces parallel to the regional dip with observed lateral extents up to 30 m that truncate underlying cross-sets and commonly act as basal surfaces to overlying cross-sets. Undulating surfaces are interpreted possibly to be deflationary supersurfaces, which formed in response to deflation or dune-field stabilisation across a regional extent. Surfaces inclined relative to the regional dip ascend between supersurfaces towards the north east at an observed angle of 3-4°. These surfaces are interpreted to be dune bounding surfaces, which are preserved when dunes climb as a result of dune-field aggradation. Aggradation of the system during the duration of the dune field's existence possibly occurred as a response to episodic increases of sediment supply into the basin, allowing dunes to climb and preserving

  14. Geological Model of Member 3 of Shahejie Formation Reservoir in Liuzan Oilfield, Eastern Hebei Province

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A new geological model of Member 3 of Shahejie Formation reservoir in the Liuzan Oilfield, eastern Hebei Province was constructed by using modern reservoir modeling technology as sequence stratigraphy and conditional simulation combined with traditional geological analysis. The model consists of a stratigraphic framework model, a structural model, a sedimentary model and a reservoir model. The study shows that the reservoir is a relatively integrated nose structure, whose strata can be divided into 4 sets of parasequence, 12 parasequences. The submerged branched channel of fan delta front is the favorable microfacies, which controls the geometric shape and physical properties of reservoir sandstone. Oil is distributed in premium reservoir sandstones at structural high positions. According to the new geological model, not only the geological contradictions appearing during oil field development are resolved, but also the oil-bearing area is enlarged by 2.7km2 and geological reserves increased by 156.9 million tons. The production capacity of the Liuzan Oilfield is increased by 0.27 million tons per year.

  15. Dynamic triggering during rupture nucleation in sandstone

    Science.gov (United States)

    Schubnel, Alexandre; Chanard, Kristel; Latour, Soumaya; Petrelis, François; Hatano, Takahiro; Mair, Karen; Vinciguerra, Sergio

    2016-04-01

    Fluid induced stress perturbations in the crust at seismogenic depths can be caused by various sources, such as deglaciation unloading, magmatic intrusion or fluid injection and withdrawal. Numbers of studies have robustly shown their link to earthquake triggering. However, the role of small periodic stress variations induced by solid earth and oceanic tides or seasonal hydrology in the seismic cycle, of the order of a few kPa, remains unclear. Indeed, the existence or absence of correlation between these loading phenomena and earthquakes have been equally proposed in the literature. To investigate this question, we performed a set of triaxial deformation experiments on porous water-saturated Fontainebleau sandstones. Rock samples were loaded by the combined action of steps of constant stress (creep), intended to simulate tectonic loading and small sinusoidal pore pressure variations with a range of amplitudes, analogous to tides or seasonal loading. All tests were conducted at a regulated temperature of 35C and a constant 35 MPa confining pressure. Our experimental results show that (1) pore pressure oscillations do not seem to influence the deformation rate at which the rock fails, (2) they correlate with acoustic emissions. Even more interestingly, we observe a progressive increase of the correlation coefficient in time as the rock approaches failure. The correlation coefficient is also sensitive to the amplitude of pore pressure oscillations as larger oscillations produce higher correlation levels. Finally, we show that, in the last hours of creep before failure, acoustic emissions occur significantly more when the pore pressure is at its lowest. This suggest that the correlation of small stress perturbations and acoustic emissions depend on the state stress of a rock and the amplitude of the perturbations and that emissions occur more likely when cracks are unclamped.

  16. Siderite (FeCO3)—the Hidden (but Primary) Player in Iron Diagenesis of Non-Marine Sandstones

    Science.gov (United States)

    Loope, D.; Kettler, R. M.

    2015-12-01

    Siderite precipitates in reducing pore waters in which iron reduction exceeds sulfate reduction. Abundant siderite should be expected in non-marine strata in which a reductant was present. The Triassic Shinarump Member (Chinle Fm) and Cretaceous Dakota Fm are fluvial and contain siderite in outcrops of floodplain mudstones. Siderite is present in cores of Dakota channel sandstones. Rinded and jointed iron-oxide concretions, Wonderstone patterns, and rhombic, iron-oxide pseudomorphs are present in outcrops of these sandstones. Vascular plants growing on floodplains provided the reductant. Similar concretions, patterns, and pseudomorphs are present in outcropping eolian cross-strata of the Jurassic Navajo Sandstone and in fluvial sandstone of the Cambrian Umm Ishrin Fm. Bleached sandstones indicate reductant was present in both units during late diagenesis. Because Jurassic deserts and Cambrian river systems lacked vascular plants, extra-formational methane was the likely reductant. We interpret the various iron-oxide-cemented phenomena of the Shinarump, Dakota, Navajo, and Umm Ishrin as products of siderite oxidation that accompanied exhumation. In the Navajo, large concretions are enclosed in thick sheaths of iron-oxide cement. Through-going horizontal and vertical joints cut sheaths. Outside concretion sheaths, joints are unassociated with iron-oxide cements, but inside the sheaths, thick cement zones are present on both sides of (still-open) joints. Joints were conduits for oxidizing water entering the concretions. Redox gradients formed on both sides of joints and iron oxide accumulated as Fe+2 diffused from dissolving siderite toward joints and O2 diffused away from joints. Horizontal joints formed <100 m from the land surface. Iron-oxide accumulations on the horizontal joints and on the vertical joints that abut them (see figure) are evidence that siderite oxidation is ongoing and linked to exhumation.

  17. THE LOWER EOCENE RODA SANDSTONE (SOUTH-CENTRAL PYRENEES:AN EXAMPLE OF A FLOOD-DOMINATED RIVER-DELTA SYSTEMIN A TECTONICALLY CONTROLLED BASIN

    Directory of Open Access Journals (Sweden)

    ROBERTO TINTERRI

    2007-07-01

    Full Text Available The lower Eocene Roda Sandstone (Figols Group, south-central Pyrenees mainly consists of mouth bars and delta-front sandstone lobes deposited in a flood-dominated river-delta system. The deposition of these bodies was strongly controlled by an interaction between flood-dominated gravity flows entering seawater, topographic confinement and tidal currents. The Roda Sandstone is made up of six depositional sequences of different hierarchical order each of which is characterized by a basal deltaic sandstone wedge (R1 to R6 that passes upward into a siltstone and mudstone interval. Each basal deltaic sandstone wedge is composed of three types of facies association and respective facies tract (sensu Mutti 1992 that, from proximal to distal zones, are indicated as T1, T2 and T3. These three facies tracts are created by the downcurrent evolution of different types of sediment-laden stream flows entering seawater and related hyperpycnal flows. Their deposits are constituted by three different types of coarse-grained mouth bars and corresponding fine-grained delta-front sandstone lobes. The tidal influence is present in facies tract T3 in the R5 and R6 sandstone units, where the passage between flood-dominated mouth bars and the delta-front sandstone lobes occurs through intermediate facies characterized by different types of sigmoidal-cross stratification whose meaning will be discussed. The basal deltaic sandstone wedges of Roda sandstone are characterized by a progressive forestepping culminating in the R6 unit that erodes the underlying R5 unit and by an overlying backstepping unit indicated as R7. The erosive surface at the base of R6 unit is interpreted as a sequence boundary that divides the Roda Sandstone into two parts: 1 an underlying highstand system tract (HST and falling stage system tract (FSST (units R1 to R5 and 2 an overlying low-stand delta (the R6 unit that passes upward into highstand mudstone through a transgressive system tract

  18. Diagenetic alteration process of chlorite in Tyr Member sandstone, Siri Canyon, Danish North Sea

    DEFF Research Database (Denmark)

    Kazerouni, Afsoon Moatari; Friis, Henrik; Hansen, Jens Peter Vind

    To evaluate the possible changes in petrology within the reservoir sand and across the oil water contact in Rau-1A, Siri Canyon Danish North Sea, 18 samples were selected and studied mainly by electron microscope and XRD. The major diagenetic phases in the well are micro quartz, large syntaxial...

  19. PRELIMINARY ESTIMATE OF CO2 STORAGE CAPACITY BY PETROPHYSICAL MODELLING IN UPPER MIOCENE POLJANA SANDSTONES IN THE WESTERN PART OF THE SAVA DEPRESSION

    Directory of Open Access Journals (Sweden)

    Marija Podbojec

    2016-02-01

    Full Text Available A preliminary assessment of the capacity of regional geological storage in the western part of the Sava Depression was based on data obtained from several deep exploration wells. The Poljana Sandstones represent a regional deep sandstone body, in most parts saturated with water, with promising underground facilities for the storage of CO₂ in the study area. Poljana Sandstones (member of Kloštar-Ivanić Formation bounded between E-log markers Rνand Z' have favourable petrophysical properties and are situated at reasonable depths. According to previous investigations, at depths greater than 800 meters supercritical conditions of temperature and pressure CO₂ are achieved, which ensures easy and safe injection into storage underground facilities. For the creation of a model in Petrel software, various data was used, including the distribution of CO₂ density, porosity, effective thickness and the relative depth of sandstone. Spatial distribution of porosity was made regarding neutron porosity logs. The most important parameter in the estimate of storage capacity is effective thickness, defined by the interval between E–log markers Rν and Z’. Hence, the effective thickness was used for top and bottom surface of sandstones. Density of CO₂ was created according to their spatial distribution regarding the depth and the temperature. The capacity of CO2 storage was calculated by the volumetric method. The use of a calculated Petrel model can subsequently determine the amount of CO₂ storage in the underground facilities of the study area.

  20. Erosion characteristic of slope sandstone soaking in acid mine drainage

    Institute of Scientific and Technical Information of China (English)

    JIANG Li-chun; CHEN Jia-sheng; WU Ai-xiang

    2007-01-01

    Acid mine drainage(AMD) is one of the main reasons of slope instability in chemical mines with high sulfide. The pH values of the solution inside the mining pit decrease with the increasing of distance from ore body and vary from 1.2 to 4.6,according to the results of the water environmental investigation and the composition test of the slope sandstone in Xinqiao Pyrite Mine. Comparative experiments between original sandstone and AMD eroded sandstone samples show that after AMD erosion the uniaxial compressive strength and elastic modulus decrease by 30%-50% and 25%-45%, respectively, the cohesion and internal friction angle decrease obviously, and the Poisson ratio fluctuates between 0.20-0.29. The greater joints development, the higher residual stress after peak value, and the longer time to damage. Besides above, the reaction mechanism analysis of AMD eroded sandstone shows that the fillings in joints and fissures of sandstone are frequently decomposed and polyreacted, resulting in changes of interior molecule structure and framework composition, and decreases of cohesion and angle of internal friction between rock structure interfaces.

  1. Petroleum system and production characteristics of the Muddy (J) Sandstone (Lower Cretaceous) Wattenberg continuous gas field, Denver basin, Colorado

    Science.gov (United States)

    Higley, D.K.; Cox, D.O.; Weimer, R.J.

    2003-01-01

    Wattenberg field is a continuous-type gas accumulation. Estimated ultimate recovery from current wells is 1.27 tcf of gas from the Lower Cretaceous Muddy (J) Sandstone. Mean gas resources that have the potential to be added to these reserves in the next 30 yr are 1.09 tcf; this will be primarily through infill drilling to recover a greater percentage of gas in place and to drain areas that are isolated because of geologic compartmentalization. Greatest gas production from the Muddy (J) Sandstone in Wattenberg field occurs (1) from within the most permeable and thickest intervals of Fort Collins Member delta-front and nearshore-marine sandstones, (2) to a lesser extent from the Horsetooth Member valley-fill channel sandstones, (3) in association with a large thermal anomaly that is delineated by measured temperatures in wells and by vitrinite reflectance contours of 0.9% and greater, (4) in proximity to the bounding Mowry, Graneros, and Skull Creek shales that are the hydrocarbon source rocks and reservoir seals, and (5) between the Lafayette and Longmont right-lateral wrench fault zones (WFZs) with secondary faults that act as conduits in areas of the field. The axis of greatest gas production is north 25 to 35?? northeast, which parallels the basin axis. Recurrent movement along five right-lateral WFZs that crosscut Wattenberg field shifted the Denver basin axis to the northeast and influenced depositional and erosional patterns of the reservoir and seal intervals. Levels of thermal maturity within the Wattenberg field are anomalously high compared to other areas of the Denver basin. The Wattenberg field thermal anomaly may be due to upward movement of fluids along faults associated with probable igneous intrusions. Areas of anomalous high heat flow within the field correlate with an increased and variable gas-oil ratio.

  2. Indirect Estimations of Frictional Coefficients of Fractures in Sandstones for Analysis of Injection Induced Microseismicity

    Science.gov (United States)

    Jo, Y.; Chang, C.; Koh, H. J.

    2014-12-01

    The frictional coefficient of fractures, a fundamental parameter needed to analyze a variety of geomechanical problems for microseismicity, is normally determined from laboratory shear tests. However, recovered rock cores are rarely available because of difficulties and high cost in getting undisturbed core samples. In that case, the frictional coefficient should be either assumed or estimated indirectly. We investigate the frictional property of fractures of various sandstones in laboratory tests and attempt to correlate that with other properties measureable relatively readily even without cores. We use various sandstones obtained from different depths of a 1 km deep borehole drilled for coal bed methane development in a Paleozoic sedimentary basin, South Korea. The sandstones have various physical properties (e.g. P-wave velocity (VP) of 2253-5038 m/s) and chemical compositions in terms of clay content (5-31%). We conduct direct shear tests in an artificial saw-cut fracture in the sandstones and determined frictional coefficients in a range of 0.36-0.57. The frictional coefficients have an inverse-linear correlation with clay contents measured from XRD analysis. These results are also quite consistent with those from previous clay gouge experiments (Takahashi et al., 2007; Tembe et al., 2010; Kohli & Zoback, 2013). They also have a linear correlation with VP. Our study demonstrates that frictional coefficients can be estimated empirically from such properties. To check feasibility of such an approach, we apply the obtained empirical relation to the borehole where cores were recovered. The clay contents in sandstone formations are estimated from the borehole gamma ray log calibrated using the XRD clay content data. Clay content estimated from gamma ray varies significantly with depth in a range of 0-45%. This range of clay content corresponds to frictional coefficients of 0.25-0.58. Comparison between estimated and measured frictional coefficients shows a

  3. Pore-scaling Modeling of Physical Property Changes During CO2 Injection into Sandstone

    Science.gov (United States)

    Keehm, Y.; Yoo, G.

    2009-12-01

    Carbon dioxide is a green-house gas and is believed to be an important factor in global warming and climate change. Many countries around the world are working on reducing and sequestrating CO2 to follow international regulations. One of promising area for CO2 sequestration is the storage in geological formation. To accurately determine the performance of geological injection and storage, quantification and monitoring of the physical property changes are essential. In this paper, we are presenting a new approach for the monitoring of CO2 sequestration in sandstone using pore-scale simulation techniques. The method consists of three steps: 1) acquisition of high-resolution pore microstructures by X-ray micro-tomography; 2) CO2 injection simulation using lattice-Boltzmann (LB) two-phase flow simulation; and 3) FEM property simulations (electrical and elastic) at different CO2 saturations during the injection. We use three different sandstone samples: sand-pack, Berea sandstone, and B2 sandstone from offshore of Korea. The porosity of the sand-pack is 42% and that of two sandstone samples is around 17%. The digital pore structures were obtained by X-ray micro-tomography with a spatial resolution of 2 micron. The LB two-phase flow simulation is then conducted by injecting CO2 into fully water-saturated samples and gives a realistic movement of CO2 in the pore structure. At each CO2 saturation, electrical and elastic properties are determined by pore-scale FEM simulation techniques. The electrical conductivity decreases almost linearly as CO2 saturations increases; however, the P-wave velocity decrease more rapidly at the low CO2 saturation (up to 30%), than at higher saturation. S-wave velocity does not show any significant changes. The higher porosity rock shows more sensitivity to saturation changes. The modeling shows that we can have quantitative relations between physical properties and CO2 saturation, which can be used to determine injection performance and

  4. Structural diagenesis in Upper Carboniferous tight gas sandstones. Lessons learned from the Piesberg analog study

    Energy Technology Data Exchange (ETDEWEB)

    Steindorf, P.; Hoehne, M.; Becker, S.; Hilgers, C. [RWTH Aachen Univ. (Germany). Energy and Mineral Resources Group (EMR); Koehrer, B. [Wintershall Holding GmbH, Barnstorf (Germany)

    2013-08-01

    Upper Carboniferous tight gas sandstone reservoirs in NW-Germany consist of thick successions of cyclothems. Our focus is the Westphalian D of the Piesberg quarry near Osnabrueck, which exposes cemented, faulted and jointed third-order coarse- to fine-grained sandstone cycles separated by anthracite coal seams. We characterize the rocks and the lateral variation of rock properties such as porosity to better constrain input data for reservoir modelling. Three cycles are exposed, each approximately 50 m thick. Rock types can be clearly distinguished by spectral gamma ray in the quarry. Sandstones are intensely compacted and cemented with quartz and generally characterized by low porosities < 8 % (Hepycnometry on plugs and cuttings). Porosities are secondary and mainly related to detrital carbonate dissolution. Around faults dissolution is higher and the porosities can increase to up to 25%. The normal faults show different throws in the quarry and bands of shale and coal have smeared into the fault at juxtaposed beds, which may result in compartments. They dominantly strike W-E and NNW-SSE, but subordinate NE-SW striking fault patterns are also present. Joints were analyzed in a 50 x 50 m section of the quarry wall using Lidar (Light detection and ranging) laser scanning, which allows the characterization of the lithology and quantitative measurement of bedding and fracture orientation data in inaccessible areas. NNE-SSW and W-E joint sets are accompanied by northeasterly and northwesterly striking sets. Around faults, fault planes and fractures are cemented with quartz veins, showing localized mass transport. Due to the intense cementation, the sandstones can reach uniaxial strengths of more than 100 MPa normal to bedding, and approximately 50 MPa parallel to bedding. Sandstone beds within and close to faults are leached by fluids, and their uniaxial strength is reduced by a factor of more than two. Our high resolution field data enables a better understanding of

  5. Effective Thermal Conductivity Modeling of Sandstones: SVM Framework Analysis

    Science.gov (United States)

    Rostami, Alireza; Masoudi, Mohammad; Ghaderi-Ardakani, Alireza; Arabloo, Milad; Amani, Mahmood

    2016-06-01

    Among the most significant physical characteristics of porous media, the effective thermal conductivity (ETC) is used for estimating the thermal enhanced oil recovery process efficiency, hydrocarbon reservoir thermal design, and numerical simulation. This paper reports the implementation of an innovative least square support vector machine (LS-SVM) algorithm for the development of enhanced model capable of predicting the ETCs of dry sandstones. By means of several statistical parameters, the validity of the presented model was evaluated. The prediction of the developed model for determining the ETCs of dry sandstones was in excellent agreement with the reported data with a coefficient of determination value ({R}2) of 0.983 and an average absolute relative deviation of 0.35 %. Results from present research show that the proposed LS-SVM model is robust, reliable, and efficient in calculating the ETCs of sandstones.

  6. Optical coherence tomography for vulnerability assessment of sandstone.

    Science.gov (United States)

    Bemand, Elizabeth; Liang, Haida

    2013-05-10

    Sandstone is an important cultural heritage material, in both architectural and natural settings, such as neolithic rock art panels. The majority of deterioration effects in porous materials such as sandstone are influenced by the presence and movement of water through the material. The presence of water within the porous network of a material results in changes in the optical coherence tomography signal intensity that can be used to monitor the wetting front of water penetration of dry porous materials at various depths. The technique is able to detect wetting front velocities from 1 cm s(-1) to 10(-6) cm s(-1), covering the full range of hydraulic conductivities likely to occur in natural sandstones from pervious to impervious.

  7. Diagenetic effect on permeabilities of geothermal sandstone reservoirs

    DEFF Research Database (Denmark)

    Weibel, Rikke; Olivarius, Mette; Kristensen, Lars

    The Danish subsurface contains abundant sedimentary deposits, which can be utilized for geothermal heating. The Upper Triassic – Lower Jurassic continental-marine sandstones of the Gassum Formation has been utilised as a geothermal reservoir for the Thisted Geothermal Plant since 1984 extracting...... and permeability is caused by increased diagenetic changes of the sandstones due to increased burial depth and temperatures. Therefore, the highest water temperatures typically correspond with the lowest porosities and permeabilities. Especially the permeability is crucial for the performance of the geothermal......-line fractures. Continuous thin chlorite coatings results in less porosity- and permeability-reduction with burial than the general reduction with burial, unless carbonate cemented. Therefore, localities of sandstones characterized by these continuous chlorite coatings may represent fine geothermal reservoirs...

  8. Finite Element Modeling of the Effect of Cementation on Mohr Coulomb Failure Criteria for Tensleep Sandstone, Alcova Anticline, Wyoming

    Science.gov (United States)

    Busetti, S.; Hennings, P.; Ramos, R.

    2011-12-01

    Vc approximately linearly, whereas φ, C0, and UCS increase non-linearly. Simulated UCS at the 0% and 100% end members is higher than experimental UCS but corresponds to initial UCS calculated from element definitions (210-279 MPa). However, defined φ and C0 consistently does not match the overall simulated response of the plug. Simulated φ is lower than defined at 17°-43° and C0 is higher at 58-89 MPa. We suspect these discrepancies are due to poroelastic effects and grain structure, which were not modeled, as well as scaling effects and dependence on sampling size and location, which are also factors in physical experiments. The results suggest that FE simulations can be used to help understand experimental strength trends. We anticipate that a numerically derived constitutive model calibrated to lithology could be used to generate property definitions from limited data sets.

  9. Revised lithostratigraphy of the Sonsela Member (Chinle Formation, Upper Triassic in the Southern Part of Petrified Forest National Park, Arizona.

    Directory of Open Access Journals (Sweden)

    Jeffrey W Martz

    Full Text Available BACKGROUND: Recent revisions to the Sonsela Member of the Chinle Formation in Petrified Forest National Park have presented a three-part lithostratigraphic model based on unconventional correlations of sandstone beds. As a vertebrate faunal transition is recorded within this stratigraphic interval, these correlations, and the purported existence of a depositional hiatus (the Tr-4 unconformity at about the same level, must be carefully re-examined. METHODOLOGY/PRINCIPAL FINDINGS: Our investigations demonstrate the neglected necessity of walking out contacts and mapping when constructing lithostratigraphic models, and providing UTM coordinates and labeled photographs for all measured sections. We correct correlation errors within the Sonsela Member, demonstrate that there are multiple Flattops One sandstones, all of which are higher than the traditional Sonsela sandstone bed, that the Sonsela sandstone bed and Rainbow Forest Bed are equivalent, that the Rainbow Forest Bed is higher than the sandstones at the base of Blue Mesa and Agate Mesa, that strata formerly assigned to the Jim Camp Wash beds occur at two stratigraphic levels, and that there are multiple persistent silcrete horizons within the Sonsela Member. CONCLUSIONS/SIGNIFICANCE: We present a revised five-part model for the Sonsela Member. The units from lowest to highest are: the Camp Butte beds, Lot's Wife beds, Jasper Forest bed (the Sonsela sandstone/Rainbow Forest Bed, Jim Camp Wash beds, and Martha's Butte beds (including the Flattops One sandstones. Although there are numerous degradational/aggradational cycles within the Chinle Formation, a single unconformable horizon within or at the base of the Sonsela Member that can be traced across the entire western United States (the "Tr-4 unconformity" probably does not exist. The shift from relatively humid and poorly-drained to arid and well-drained climatic conditions began during deposition of the Sonsela Member (low in the Jim Camp

  10. MINERALOGICAL CHARACTERIZATION OF SANDSTONE AND CLAY, NORTH-EAST CONSTANTINE.

    Directory of Open Access Journals (Sweden)

    M BENYAMINA

    2016-06-01

    Full Text Available The north-east area of Constantine has a very complex geological setting. The variety of sedimentary rocks such as sandstone and clay in abundance, represent a big importance in the industry and road infrastructure. The X-ray diffraction (XRD analysis, Scanning Electron Microscopy SEM/EDS, FTIR spectroscopy of sandstone and clay are required for qualitative and quantitative analysis of the existing phases. In addition, chemical analysis of the same samples is required to confirm the XRD, EDS (Energy Dispersive X ray Spectroscopy and FTIR spectroscopy results. The results of this multidisciplinary study, obtained by various analytical techniques, show a good agreement on the existing phases.

  11. Natural and Laboratory-Induced Compaction Bands in Aztec Sandstone

    Science.gov (United States)

    Haimson, B. C.; Lee, H.

    2002-12-01

    The Aztec sandstone used in this research is from the Valley of Fire State Park area, Nevada. This Jurassic aeolian sandstone is extremely weak (uniaxial compressive strength of 1-2 MPa); porosity averages 26%; grains are subrounded and have a bimodal size distribution (0.1 mm and 0.5 mm); its mineral composition (K. Sternlof, personal comm.) is 93% quartz, 5% k-spar, and 2% kaolinite, Fe carbonate and others; grain bonding is primarily through suturing. Sternlof et al. (EOS, November, 2001) observed substantial exposure of mainly compactive deformation bands in the Aztec sandstone. We studied an SEM image of a compaction band found in a hand sample of the Aztec sandstone. We also conducted a drilling test in a 130x130x180 mm prismatic specimen subjected to a preset far-field true triaxial stress condition (\\sigmah = 15 MPa, \\sigmav = 25 MPa, \\sigmaH = 40 MPa). Drilling of a 20 mm dia. vertical hole created a long fracture-like thin tabular breakout along the \\sigmah springline and perpendicular to \\sigmaH direction. SEM analysis of the zones ahead of the breakout tips revealed narrow bands of presumed debonded intact grains interspersed with grain fragments. We infer that the fragments were formed from multiple splitting or crushing of compacted grains in the band of high compressive stress concentration developed along the \\sigmah springline. SEM images away from the breakout tip surroundings showed no such fragments. SEM study of the natural compaction band showed a similar arrangement of mainly intact grains surrounded by grain fragments. Using the Optimas optical software package, we found the percentage of pore area within the band ahead of the breakout tips to average 17%; outside of this zone it was 23%. In the natural compaction band pore area occupied 8.5% of the band; in the host rock adjacent to the compaction band it averaged 19%. These readings strongly suggest porosity reduction due to compaction in both cases. The close resemblance between the

  12. A new Basal sauropodomorph dinosaur from the Lower Jurassic Navajo sandstone of Southern Utah.

    Directory of Open Access Journals (Sweden)

    Joseph J W Sertich

    Full Text Available BACKGROUND: Basal sauropodomorphs, or 'prosauropods,' are a globally widespread paraphyletic assemblage of terrestrial herbivorous dinosaurs from the Late Triassic and Early Jurassic. In contrast to several other landmasses, the North American record of sauropodomorphs during this time interval remains sparse, limited to Early Jurassic occurrences of a single well-known taxon from eastern North America and several fragmentary specimens from western North America. METHODOLOGY/PRINCIPAL FINDINGS: On the basis of a partial skeleton, we describe here a new basal sauropodomorph dinosaur from the Lower Jurassic Navajo Sandstone of southern Utah, Seitaad ruessi gen. et sp. nov. The partially articulated skeleton of Seitaad was likely buried post-mortem in the base of a collapsed dune foreset. The new taxon is characterized by a plate-like medial process of the scapula, a prominent proximal expansion of the deltopectoral crest of the humerus, a strongly inclined distal articular surface of the radius, and a proximally and laterally hypertrophied proximal metacarpal I. CONCLUSIONS/SIGNIFICANCE: Phylogenetic analysis recovers Seitaad as a derived basal sauropodomorph closely related to plateosaurid or massospondylid 'prosauropods' and its presence in western North America is not unexpected for a member of this highly cosmopolitan clade. This occurrence represents one of the most complete vertebrate body fossil specimens yet recovered from the Navajo Sandstone and one of the few basal sauropodomorph taxa currently known from North America.

  13. Hyporheic zone influences on concentration-discharge relationships in a headwater sandstone stream

    Science.gov (United States)

    Hoagland, Beth; Russo, Tess A.; Gu, Xin; Hill, Lillian; Kaye, Jason; Forsythe, Brandon; Brantley, Susan L.

    2017-06-01

    Complex subsurface flow dynamics impact the storage, routing, and transport of water and solutes to streams in headwater catchments. Many of these hydrogeologic processes are indirectly reflected in observations of stream chemistry responses to rain events, also known as concentration-discharge (CQ) relations. Identifying the relative importance of subsurface flows to stream CQ relationships is often challenging in headwater environments due to spatial and temporal variability. Therefore, this study combines a diverse set of methods, including tracer injection tests, cation exchange experiments, geochemical analyses, and numerical modeling, to map groundwater-surface water interactions along a first-order, sandstone stream (Garner Run) in the Appalachian Mountains of central Pennsylvania. The primary flow paths to the stream include preferential flow through the unsaturated zone ("interflow"), flow discharging from a spring, and groundwater discharge. Garner Run stream inherits geochemical signatures from geochemical reactions occurring along each of these flow paths. In addition to end-member mixing effects on CQ, we find that the exchange of solutes, nutrients, and water between the hyporheic zone and the main stream channel is a relevant control on the chemistry of Garner Run. CQ relationships for Garner Run were compared to prior results from a nearby headwater catchment overlying shale bedrock (Shale Hills). At the sandstone site, solutes associated with organo-mineral associations in the hyporheic zone influence CQ, while CQ trends in the shale catchment are affected by preferential flow through hillslope swales. The difference in CQ trends document how the lithology and catchment hydrology control CQ relationships.

  14. Donghe Sandstone Subtle Reservoir Exploration and Development Technology in Hade 4 Oilfield

    Institute of Scientific and Technical Information of China (English)

    SunLongde; ZhouXinyuan; SongWenjie; JiangTongwen; ZhuWeihong; YangPing; NiuYujie; DiHongli

    2004-01-01

    Hade 4 oilfield is located on the Hadexun tectonic belt north of the Manjiaer depression in the Tarim basin, whose main target layer is the Donghe sandstone reservoir, with a burial depth over 5,000m and an amplitude below 34m, at the bottom of the Carboniferous. The Donghe sandstone reservoir consists of littoral facies deposited quartz sandstones of the transgressive system tract, overlapping northward and pinching out. Exploration and development confirms that water-oil contact tilts from the southeast to the northwest with a drop height of nearly 80m. The reservoir, under the control of both the stratigraphic overlap pinch-out and tectonism, is a typical subtle reservoir. The Donghe sandstone reservoir in Hade 4 oilfield also has the feature of a large oil-bearing area (over 130 km2 proved), a small thickness (average efficient thickness below 6m) and a low abundance (below 50)< 104t/km2). Moreover, above the target layer developed a set of igneous rocks with an uneven thickness in the Permian formation, thus causing a great difficulty in research of the velocity field. Considering these features,an combination mode of exploration and development is adopted, namely by way of whole deployment, step-by-step enforcement and rolling development with key problems to be tackled, in order to further deepen the understanding and enlarge the fruits of exploration and development. The paper technically focuses its study on the following four aspects concerning problem tackling. First, to strengthen the collecting, processing and explanation of seismic data, improve the resolution, accurately recognize the pinch-out line of the Donghe sandstone reservoir by combining the drilling materials in order to make sure its distribution law; second, to strengthen the research on velocity field, improve the accuracy of variable speed mapping, make corrections by the data from newlydrilled key wells and, as a result, the precision of tectonic description is greatly improved; third

  15. Trilobites from the Middle Ordovician Stairway Sandstone, Amadeus Basin, central Australia

    DEFF Research Database (Denmark)

    Jakobsen, Kristian Grube; Nielsen, Arne Thorshøj; Harper, David Alexander Taylor;

    2014-01-01

    During the Middle Ordovician (Darriwilian) sandstones and siltstones were deposited in the epicontinental Larapintine Sea, which covered large parts of central Australia. The Darriwilian Stairway Sandstone has, for the first time, been sampled stratigraphically for macrofossils to track marine be...

  16. Continuity and internal properties of Gulf Coast sandstones and their implications for geopressured fluid production

    Energy Technology Data Exchange (ETDEWEB)

    Morton, R.A.; Ewing, T.E.; Tyler, N.

    1983-01-01

    The intrinsic properties of the genetic sandstone units that typify many geopressured geothermal aquifers and hydrocarbon reservoirs in the Gulf Coast region were systematically investigated classified, and differentiated. The following topics are coverd: structural and stratigraphic limits of sandstone reservoirs, characteristics and dimensions of Gulf Coast sandstones; fault-compartment areas; comparison of production and geologic estimates of aquifer fluid volume; geologic setting and reservoir characteristics, Wells of Opportunity; internal properties of sandstones; and implications for geopressured fluid production. (MHR)

  17. The effect of hot water injection on sandstone permeability

    DEFF Research Database (Denmark)

    Rosenbrand, Esther; Haugwitz, Christian; Jacobsen, Peter Sally Munch;

    2014-01-01

    Seasonal energy storage can be achieved by hot water injection in geothermal sandstone aquifers. We present an analysis of literature data in combination with new short-term flow through permeability experiments in order to address physical and physico-chemical mechanisms that can alter...

  18. DELAYED POLYMER CROSSLINKING USED FOR PROFILE CONTROL IN SANDSTONE RESERVOIRS

    Institute of Scientific and Technical Information of China (English)

    Wang Zhongmao; Dong Bo; Fu Xiaofeng; Rong Jiashu

    1997-01-01

    @@ Most of the oil reservoirs in Jilin province occur in fractured sandstone with low permeability and heavy heterogeneity. In addition, with fracture development, the artificial fractures around producing wells and water injection wells have been increased, further aggravating the heterogeneity of oil reservoirs.

  19. Diagenetic effect on permeabilities of geothermal sandstone reservoirs

    DEFF Research Database (Denmark)

    Weibel, Rikke; Olivarius, Mette; Kristensen, Lars

    The Danish subsurface contains abundant sedimentary deposits, which can be utilized for geothermal heating. The Upper Triassic – Lower Jurassic continental-marine sandstones of the Gassum Formation has been utilised as a geothermal reservoir for the Thisted Geothermal Plant since 1984 extracting ...

  20. Diagenesis, provenance and depositional environments of the Bunter Sandstone Formation

    DEFF Research Database (Denmark)

    Olivarius, Mette; Weibel, Rikke; Friis, Henrik

    The Bunter Sandstone Formation in the northern North German Basin has large geothermal potential with high porosity and permeability (generally >15% and >100 mD, respectively) and with pore fluid temperatures that are adequate for geothermal energy production (c. 55–60˚C). A combined investigatio...

  1. Inelastic compaction, dilation and hysteresis of sandstones under hydrostatic conditions

    Science.gov (United States)

    Shalev, Eyal; Lyakhovsky, Vladimir; Ougier-Simonin, Audrey; Hamiel, Yariv; Zhu, Wenlu

    2014-05-01

    Sandstones display non-linear and inelastic behaviour such as hysteresis when subjected to cyclic loading. We present three hydrostatic compaction experiments with multiple loading-unloading cycles on Berea and Darley Dale sandstones and explain their hysteretic behaviour using non-linear inelastic compaction and dilation. Each experiment included eight to nine loading-unloading cycles with increasing maximum pressure in each subsequent cycle. Different pressure-volumetric strain relations during loading and unloading were observed. During the first cycles, under relatively low pressures, not all of the volumetric strain is recovered at the end of each cycle whereas at the last cycles, under relatively high pressures, the strain is recovered and the pressure-volumetric strain hysteresis loops are closed. The observed pressure-volumetric strain relations are non-linear and the effective bulk modulus of the sandstones changes between cycles. Observations are modelled with two inelastic deformation processes: irreversible compaction caused by changes in grain packing and recoverable compaction associated with grain contact adhesion, frictional sliding on grains or frictional sliding on cracks. The irreversible compaction is suggested to reflect rearrangement of grains into a more compact mode as the maximum pressure increases. Our model describes the `inelastic compaction envelope' in which sandstone sample will follow during hydrostatic loading. Irreversible compaction occurs when pressure is greater than a threshold value defined by the `inelastic compaction envelope'.

  2. Contribution of terrigenous rocks of South Belgian coal deposits in geological storage of CO2 : the sandstones case

    Science.gov (United States)

    Dupont, N.; Baele, J.-M.

    2009-04-01

    Sequestration of CO2 in unmined coal seams is one of the different options for storing CO2 in geological reservoirs. In favorable situations, it could be coupled with the retrieving of adsorbed methane from coal (ECBM), which can make this solution economically more attractive. However, in the case of South Belgian coal measures, both weak permeability of the coal and frequent faulting/folding of the seams are likely to decrease the efficiency of this technique. Westphalian A and B sediments from South Belgium are containing only about 2.5% vol. of coal; the other rocks consisting of shales/siltstones (~80%) and sandstones (~20%). For all these lithologies, the main processes of CO2 sequestration are 1) adsorption in coal and clay minerals that are partly forming shales, and within rock porosity in the case of sandstones and, to a lesser extent, in the shales/siltstone porosity. In a previous assessment of the sequestration potential in Westphalian coal measures of South Belgium, Baele et al. (2007) showed that coal and shales each account for 25% of the total sequestration potential, and the rest, i.e. 50%, is related to sandstones on a basis of 2% porosity. Beside their significant additional storage capacity, sandstones have also a better permeability than the other finer-grained and organic lithologies. Additionally, sandstones are known to occasionally cut the coal seams (wash-out), thus providing insights in increasing accessibility of injected CO2 into the coal. On the other hand, some sandstone banks are fossil braided rivers that induced peripheral fractures by differential compaction during burial diagenesis (Van Tongeren et al., 2000). These fractures are thus likely to have increased accessibility from high-injectivity sandstones to surrounding lithologies that could significantly contribute to storage capacity. The aim of this study is to refine the contribution of the westphalian South Belgium sandstones to the geological storage of CO2. Measurements

  3. Chemical analysis of black crust on the Angkor sandstone at the Bayon temple, Cambodia

    Science.gov (United States)

    Song, Wonsuh; Oguchi, Chiaki; Waragai, Tetsuya

    2014-05-01

    The Angkor complex is the one of the greatest cultural heritages in the world. It is constructed in the early 12th century, designated as a world cultural heritage by UNESCO in 1992. The temples at the Angkor complex are mainly made of sandstone and laterite. However, due to the tropical climate, plants, lichens and various microorganisms are growing well on the rock surface. Black crusts are also easily found on the stone surface. The 21st technical session of the International Coordinating Committee for the Safeguarding and Development of the Historic Site of Angkor (ICC-Angkor) held in 2012 recommended that to preserve both the biofilms and the forest cover and to prohibit the biocides (chlorine-based) and organic biocides. However, there are many reports that lichens and microorganisms accelerate rock weathering. It is important to clarify that how the biofilm on the Angkor temples affect Angkor sandstones. We sampled Angkor sandstone covered by black crust at the Bayon temple, Angkor complex, and observed the section and the surface of the rock sample by using SEM. Surfaces of the samples are not polished in order to observe the original condition. The samples are coated with gold for 180 seconds. The depth of the black crust is up to 1 mm. Many filamentous materials were found on the black crust. Average energy-dispersive X-ray spectroscopy data of the five areas of ca. 20 μm ×15 μm in the black crusts shows that over 80 % of the filamentous materials are compounds of carbon. It seems that these materials are hyphae. The shape of the hypha is like a thread and its size is few μm in diameter and up to several centimeters in length. Black crusts are consisted of elements and compounds of carbon, Na, Mg, Al, Si, Cl, K, Ca, and Fe. Further research has to be done to find out the better and proper way of conservation for the Angkor complex.

  4. The geological constraints of the development of sandstone landforms in Central Europe, a case study of the Świętokrzyskie (Holy Cross) Mountains, Poland

    Science.gov (United States)

    Urban, Jan

    2016-12-01

    Eighty sites of crag groups and individual crags occurring in the Świętokrzyskie (Holy Cross) Mts., upland situated in central Poland, were described in detail in order to examine the lithological, structural, mechanic properties and the tectonic features of sandstones and quartzites representing six crag-forming lithostratigraphic units: Cambrian quartzites, Devonian quartzitic sandstones, Triassic and Jurassic sandstones. Specific features of these rocks are: their occurrence within the sequences consisting of different rock series, high energy depositional environments and siliceous composition. The cragforming rocks differ in the amount of cement (from strongly cemented quartzites to very porous sandstones with poor cement), which determines the diverse mechanical properties (from very strong to friable rocks). The crucial feature enabling formation of crags built of porous and friable sandstones is very dense grain packing due to chemical and mechanical compaction. Regarding the principal role of the gravitational disintegration of rock massifs under the periglacial conditions in the Late Pleistocene, other factors constraining the crag formation and shaping are: the tectonic situation of rocks (the orientation of strata and joints) as well as adequate joint spacing and bed thickness. Petrographic, structural and tectonic features are interrelated.

  5. Crushing behavior of lightmass structural member

    Institute of Scientific and Technical Information of China (English)

    Kil-Sung LEE; Yong-June YANG; Woo-Chae HWANG; In-Young YANG

    2009-01-01

    Carbon fiber reinforced plastic (CFRP) of the advanced composite materials is widely used in lightmass structural materials of air planes, ship and automobiles because of high strength and stiffness. In this study, experimental investigation was performed for each specimen. The square section members consist of aluminum, CFRP and hybrid (aluminum/CFRP) member, and hat-shaped section members consist of CFRP and hybrid (aluminum/CFRP) members specimen. Based on the collapse characteristics of aluminum square section member, the collapse characteristics and energy absorption capability of hat-shaped section members were analyzed. The axial static collapse tests were carried out for each section member. The collapse modes and the energy absorption capability of the members were analyzed. In the lightmass design aspect, the collapse characteristics and energy absorption capability of the members were compared.

  6. Traces of the heritage arising from the Macelj sandstone

    Science.gov (United States)

    Golež, Mateja

    2014-05-01

    The landscape of Southeast Slovenia and its stone heritage principally reveal itself through various Miocene sandstones. The most frequently found type on the borderline between Slovenia and Croatia, i.e. east of Rogatec, is the micaceous-quartz Macelj sandstone. This rock ranges in colour from greenish grey to bluish grey and yellowish, depending on the content of glauconite, which colours it green. In its composition, the rock is a heterogeneous mixture of grains of quartz, dolomite, muscovite, microcline, anorthite and glauconite. The average size of grains is 300μm. In cross-section, they are oblong, semi-rounded or round. The mechanical-physical and durability properties of the Macelj sandstone, which have been characterised pursuant to the applicable standards for natural stone, reveal that the rock exhibits poor resistance to active substances from the atmosphere, particularly in the presence of salt. In the surroundings of Rogatec, there are around 45 abandoned quarries of the Macelj sandstone, which are the result of the exploitation of this mineral resource from the 17th century on. The local quarrymen earned their bread until 1957, when the Kambrus quarry industry closed down. From the original use of this mineral resource as construction and decorative material, the useful value of the Macelj sandstone expanded during the development of the metals industry to the manufacture of large and small grindstones for the needs of the domestic and international market. Therefore, traces of quarrying can not only be seen in the disused quarries, but also in the rich architectural heritage of Rogatec and its surroundings, the stone furniture - from portals, window frames, wells, various troughs, pavements to stone walls - and other. The living quarrying heritage slowly passed into oblivion after World War II, although the analysis of the social image of the people residing in Rogatec and its surroundings revealed that there was an average of one stonemason in

  7. Origins of massive-type sandstones in braided river systems

    Science.gov (United States)

    Martin, Charlotte A. L.; Turner, Brian R.

    1998-07-01

    This study details largely ignored massive-type, predominantly structureless sandstones preserved within braided fluvial successions of Carboniferous to Triassic age. Architectural element analysis reveals that these sediments were deposited within sand-dominated perennial systems of low braiding index. Cross-stratified braid bar deposits are interbedded with, and laterally equivalent to geometrically distinct, largely structureless massive-type sandbodies identified as two separate architectural elements: channel-like (SMC) and sheet-like (SMS). Sub-divisions within these broad categories define six geometric units which are texturally distinct from each other and from the structured sediments of the same lithological unit. Since massive-type sandstone elements have many features in common with the deposits of highly concentrated, laminar sediment/water flows, they are interpreted in terms of similar depositional processes. SMC elements form elongate channel-like features which trend both at high angles to, and parallel with, the palaeoflow of host fluvial channels. The lower bounding surfaces of SMC elements may be either erosive or non-erosive, and describe symmetrical cross-sections with margins dipping debris flows related to fluvial bank and/or bar collapse. SMS elements form sandsheets up to 8 m in thickness which may be traced >250 m parallel and transverse to the fluvial palaeoflow direction established from cross-stratified sandstones of adjacent architectural elements. The basal surface of SMS elements may either be undulose (where the sandbodies are termed SMSU) or erosional (where they are termed SMSE). Internally SMSU elements preserve parallel laminae marginal to basal scours, diffuse sweeping laminae, isolated cross-sets and water escape structures. The SMSU sediments are compositionally identical to the structured sandstones with which they are associated and are interpreted as the result of deposition from highly concentrated stream flows

  8. Chip Multithreaded Consistency Model

    Institute of Scientific and Technical Information of China (English)

    Zu-Song Li; Dan-Dan Huan; Wei-Wu Hu; Zhi-Min Tang

    2008-01-01

    Multithreaded technique is the developing trend of high performance processor. Memory consistency model is essential to the correctness, performance and complexity of multithreaded processor. The chip multithreaded consistency model adapting to multithreaded processor is proposed in this paper. The restriction imposed on memory event ordering by chip multithreaded consistency is presented and formalized. With the idea of critical cycle built by Wei-Wu Hu, we prove that the proposed chip multithreaded consistency model satisfies the criterion of correct execution of sequential consistency model. Chip multithreaded consistency model provides a way of achieving high performance compared with sequential consistency model and ensures the compatibility of software that the execution result in multithreaded processor is the same as the execution result in uniprocessor. The implementation strategy of chip multithreaded consistency model in Godson-2 SMT processor is also proposed. Godson-2 SMT processor supports chip multithreaded consistency model correctly by exception scheme based on the sequential memory access queue of each thread.

  9. Quantitative study on experimentally observed poroelastic behavior of Berea sandstone in two-phase fluid system

    Science.gov (United States)

    Goto, Hiroki; Aichi, Masaatsu; Tokunaga, Tomochika; Yamamoto, Hajime; Ogawa, Toyokazu; Aoki, Tomoyuki

    2014-08-01

    Coupled two-phase fluid flow and poroelastic deformation of Berea sandstone is studied through laboratory experiment and numerical simulation. In the experiment, compressed air was infiltrated from the bottom of a water-saturated cylindrical Berea sandstone sample under hydrostatic external stress condition. Both axial and circumferential strains at half the height of the sample showed sudden extension and monotonic and gradual extension afterward. Numerical simulation based on thermodynamically consistent constitutive equations was conducted in order to quantitatively analyze the experimental results. In a simulation assuming isotropy of material properties, the volumetric discharge rate of water at the outlet and one of the axial, circumferential, and volumetric strains at half the height of the sample were reproduced well by each parameter set, while the other two strains were not. When introducing transverse isotropy, all the experimental data were reproduced well. In addition, the effect of saturation dependency of Bishop's effective stress coefficient on the deformation behavior of porous media was discussed, and it was found that strains, both axial and circumferential, are sensitive to the coefficient.

  10. Effect Of Hot Water Injection On Sandstone Permeability

    DEFF Research Database (Denmark)

    Rosenbrand, Esther; Fabricius, Ida Lykke

    2012-01-01

    The seasonal imbalance between supply and demand of renewable energy requires temporary storage, which can be achieved by hot water injection in warm aquifers. This requires that the permeability and porosity of the aquifer are not reduced significantly by heating. We present an overview...... of published results regarding the effect of temperature on sandstone permeability. These tests are performed with mineral oil, nitrogen gas, distilled water and solutions of NaCl, KCl, CaCl2 as well as brines that contain a mixture of salts. Thirteen sandstone formations, ranging from quartz arenites...... not account for all the permeability reductions observed. Permeablity reduction occurs both when distilled water is the saturating fluid as well as in tests with NaCl, KCl or CaCl2 solutions, however, this is not the case in tests with mineral oil or nitrogen gas. The formation of a filter cake or influx...

  11. Comparative study between Botucatu and Berea sandstone properties

    Science.gov (United States)

    Cardoso, Oldemar Ribeiro; Balaban, Rosangela de Carvalho

    2015-10-01

    The aim of the present study is the analysis and comparison between Berea and Botucatu sandstone, concerning the problems with regard to the loss of permeability or water sensitivity or loss of hydraulic conductivity due to the presence of swelling or non-swelling clays. Some porous volumes of synthetic seawater of different salinities were displaced through the porous media of Berea and Botucatu formations. It was observed that even the plugs of Berea, with no-swelling clays in their composition, had the permeability reduced as soon as the brine salinity reached a lower limit. As expected, the same occurred with the Botucatu sandstone samples, however, in this case,the sensitivity to the low salinity was much more effective.

  12. Study of microwave response of coal and sandstone samples

    Science.gov (United States)

    Singh, R.; Singh, Ramesh P.; Singh, K. P.

    1980-07-01

    Detailed measurements of relative dielectric constant and loss tangent of coal and sandstone samples have been carried out in the X-band of microwave frequency range (8-10 GHz). The effect of moisture, saline and petrol content on the dielectric and loss tangent has been studied. The reflection and transmission coefficient of these samples have been computed. The application of such measurements to geophysical prospecting has been discussed.

  13. New Acid Combination for a Successful Sandstone Acidizing

    Science.gov (United States)

    Shafiq, M. U.; Mahmud, H. K. B.; Rezaee, R.

    2017-05-01

    With the development of new enhanced oil recovery techniques, sandstone acidizing has been introduced and played a pivotal role in the petroleum industry. Different acid combinations have been applied, which react with the formation, dissolve the soluble particles; thus increase the production of hydrocarbons. To solve the problems which occurred using current preflush sandstone acidizing technology (hydrochloric acid); a new acid combination has been developed. Core flooding experiments on sandstone core samples with dimensions 1.5 in. × 3 in. were conducted at a flow rate of 2 cm3/min. A series of hydrochloric-acetic acid mixtures with different ratios were tested under 150°F temperature. The core flooding experiments performed are aimed to dissolve carbonate, sodium, potassium and calcium particles from the core samples. These experiments are followed by few important tests which include, porosity-permeability, pH value, Inductively Coupled Plasma (ICP) analysis and Nuclear Magnetic Resonance (NMR measurements). All the results are compared with the results of conventional hydrochloric acid technology. NMR and porosity analysis concluded that the new acid combination is more effective in creating fresh pore spaces and thus increasing the reservoir permeability. It can be seen from the pore distribution before and after the acidizing. Prior applying acid; the large size of pores appears most frequently in the pore distribution while with the applied acid, it was found that the small pore size is most the predominant of the pore distribution. These results are validated using ICP analysis which shows the effective removal of calcium and other positive ions from the core sample. This study concludes that the combination of acetic-hydrochloric acid can be a potential candidate for the preflush stage of sandstone acidizing at high temperature reservoirs.

  14. Strength and elastic properties of sandstone under different testing conditions

    Institute of Scientific and Technical Information of China (English)

    CHEN Yun-ping; WANG Si-jing; WANG En-zhi

    2007-01-01

    A laboratory experimental program performed on Wuhan sandstones was presented under monotonic loading, partial cyclic loading during loading path and sine wave cyclic loading with different strain rates to compare uniaxial compression strength and elastic properties (elastic modulus and Poisson ratio) under different conditions and influence of pore fluid on them. When the loading strain rates are 10-5, 10-4 and 10-3/s, uniaxial compression strengths of dry sandstones are 82.3, 126.6 and 141.6 MPa,respectively, and that of water saturated sandstones are 70.5, 108.3 and 124.1 MPa, respectively. The above results show that the uniaxial compression strength increases with the increase of strain rate, however, variation of softening coefficient is insignificant.Under monotonic loading condition, tangent modulus increases with an increment of stress (strain) to a maximum value at a certain stress level, beyond which it starts to decline. Under the partial cyclic loading during loading path condition, unloading or reloading modulus is larger than loading modulus, and unloading and reloading moduli are almost constants with respect to stress level,especially unloading modulus. Under the sine wave cyclic loading condition, tangent modulus and Poisson ratio display asymmetric 'X' shape with various strain, and the average unloading modulus is larger than the average loading modulus.

  15. Calcium lignosulfonate adsorption and desorption on Berea sandstone.

    Science.gov (United States)

    Grigg, Reid B; Bai, Baojun

    2004-11-01

    This paper describes adsorption and desorption studies carried out with calcium lignosulfonate (CLS) on Berea sandstone. Circulation experiments were performed to determine CLS adsorption isotherms and the effects of CLS concentration, temperature, salinity, brine hardness, and injection rate on adsorption density. Flow-through experiments were performed to assess the reversibility of CLS adsorption and the influence of postflush rate, brine concentration, brine hardness, brine pH, and temperature on the desorption process. Results indicate that CLS adsorption isotherms on Berea sandstone follow the Freundlich isotherm law. The results presented in this paper on the effects of CLS adsorption and desorption on Berea sandstone show that: (1) increasing CLS concentration and salinity increases CLS adsorption density; (2) increasing temperature will decrease adsorption density; (3) increasing injection rate of CLS solution will slightly decrease CLS adsorption density; (4) postflush rate and salinity of brine have a large impact on the CLS desorption process; (5) the adsorption and desorption process are not completely reversible; and (5) temperature and pH of the postflush brine have little effect on desorption.

  16. CO2 sequestration in feldspar-rich sandstone: Coupled evolution of fluid chemistry, mineral reaction rates, and hydrogeochemical properties

    Science.gov (United States)

    Tutolo, Benjamin M.; Luhmann, Andrew J.; Kong, Xiang-Zhao; Saar, Martin O.; Seyfried, William E.

    2015-07-01

    To investigate CO2 Capture, Utilization, and Storage (CCUS) in sandstones, we performed three 150 °C flow-through experiments on K-feldspar-rich cores from the Eau Claire formation. By characterizing fluid and solid samples from these experiments using a suite of analytical techniques, we explored the coupled evolution of fluid chemistry, mineral reaction rates, and hydrogeochemical properties during CO2 sequestration in feldspar-rich sandstone. Overall, our results confirm predictions that the heightened acidity resulting from supercritical CO2 injection into feldspar-rich sandstone will dissolve primary feldspars and precipitate secondary aluminum minerals. A core through which CO2-rich deionized water was recycled for 52 days decreased in bulk permeability, exhibited generally low porosity associated with high surface area in post-experiment core sub-samples, and produced an Al hydroxide secondary mineral, such as boehmite. However, two samples subjected to ∼3 day single-pass experiments run with CO2-rich, 0.94 mol/kg NaCl brines decreased in bulk permeability, showed generally elevated porosity associated with elevated surface area in post-experiment core sub-samples, and produced a phase with kaolinite-like stoichiometry. CO2-induced metal mobilization during the experiments was relatively minor and likely related to Ca mineral dissolution. Based on the relatively rapid approach to equilibrium, the relatively slow near-equilibrium reaction rates, and the minor magnitudes of permeability changes in these experiments, we conclude that CCUS systems with projected lifetimes of several decades are geochemically feasible in the feldspar-rich sandstone end-member examined here. Additionally, the observation that K-feldspar dissolution rates calculated from our whole-rock experiments are in good agreement with literature parameterizations suggests that the latter can be utilized to model CCUS in K-feldspar-rich sandstone. Finally, by performing a number of reactive

  17. Rock doughnut and pothole structures of the Clarens Fm. Sandstone in the Karoo Basin, South Africa: Possible links to Lower Jurassic fluid seepage

    Science.gov (United States)

    Grab, Stefan; Svensen, Henrik

    2011-08-01

    South Africa has a wealth of sandstone landforms, yet many of these have not been examined in detail to expand knowledge on their morphology and process origins. Here we present data on primary morphological statistics, rock hardness, surface roughness and petrographic investigations of rock doughnuts and associated pothole structures in Golden Gate Highlands National Park (GGHNP) and in the Witkop III complex, with the aim of using such data and field observations to argue their likely origins. Schmidt hammer R-values indicate consistently harder doughnut rims (mean = 48.7; n = 150) than the enclosed potholes (mean = 37.8; n = 150) and surrounding sandstone platform (mean = 39.7; n = 250). The petrography of Clarens Fm. Sandstone shows that the typical whitish sandstone is affected by intense chemical weathering. Pothole rims and the irregular reddish crust typical of the Witkop III outcrops show a secondary cementation by microcrystalline silica. Although preservation of old land surfaces is difficult to prove, small and circular pipe structures filled with calcite-cemented sand are present locally surrounding the Witkop III hydrothermal complex, and represent conduits for fluidized sand. Based on the morphologies of the Witkop III summit with the associated potholes and pipes, we hypothesize that they are remnants of morphologies created by Jurassic fluid seepage, with a superimposed and secondary silica cementation. Given that fluidization structures evidently occur in Clarens Fm. Sandstone, as is the case at Witkop, such mechanisms could possibly have contributed to the observed rock doughnut structures elsewhere on Clarens Fm. Sandstones, such as at the GGHNP where the rock doughnut morphological attributes are typical to landforms originating from fluid venting.

  18. On the water saturation calculation in hydrocarbon sandstone reservoirs

    Energy Technology Data Exchange (ETDEWEB)

    Stalheim, Stein Ottar

    2002-07-01

    The main goal of this work was to identify the most important uncertainty sources in water saturation calculation and examine the possibility for developing new S{sub w} - equations or possibility to develop methods to remove weaknesses and uncertainties in existing S{sub w} - equations. Due to the need for industrial applicability of the equations we aimed for results with the following properties: The accuracy in S{sub w} should increase compared with existing S{sub w} - equations. The equations should be simple to use in petrophysical evaluations. The equations should be based on conventional logs and use as few as possible input parameters. The equations should be numerical stable. This thesis includes an uncertainty and sensitivity analysis of the most common S{sub w} equations. The results are addressed in chapter 3 and were intended to find the most important uncertainty sources in water saturation calculation. To increase the knowledge of the relationship between R{sub t} and S{sub w} in hydrocarbon sandstone reservoirs and to understand how the pore geometry affects the conductivity (n and m) of the rock a theoretical study was done. It was also an aim to examine the possibility for developing new S{sub w} - equations (or investigation an effective medium model) valid inhydrocarbon sandstone reservoirs. The results are presented in paper 1. A new equation for water saturation calculation in clean sandstone oil reservoirs is addressed in paper 2. A recommendation for best practice of water saturation calculation in non water wet formation is addressed in paper 3. Finally a new equation for water saturation calculation in thinly interbedded sandstone/mudstone reservoirs is presented in paper 4. The papers are titled: 1) Is the saturation exponent n a constant. 2) A New Model for Calculating Water Saturation In 3) Influence of wettability on water saturation modeling. 4) Water Saturation Calculations in Thinly Interbedded Sandstone/mudstone Reservoirs. A

  19. Experimental deformation in sandstone, carbonates and quartz aggregate

    Energy Technology Data Exchange (ETDEWEB)

    Cheung, Cecilia See Nga [Stony Brook Univ., NY (United States)

    2015-05-01

    The first part of my thesis is mainly focused on the effect of grain size distribution on compaction localization in porous sandstone. To identify the microstructural parameters that influence compaction band formation, I conducted a systematic study of mechanical deformation, failure mode and microstructural evolution in Bleurswiller and Boise sandstones, of similar porosity (~25%) and mineralogy but different sorting. Discrete compaction bands were observed to develop over a wide range of pressure in the Bleurswiller sandstone that has a relatively uniform grain size distribution. In contrast, compaction localization was not observed in the poorly sorted Boise sandstone. My results demonstrate that grain size distribution exerts important influence on compaction band development, in agreement with recently published data from Valley of Fire and Buckskin Gulch, as well as numerical studies. The second part aimed to improve current knowledge on inelastic behavior, failure mode and brittle-ductile transition in another sedimentary rock, porous carbonates. A micritic Tavel (porosity of ~13%) and an allochemical Indiana (~18%) limestones were deformed under compaction in wet and dry conditions. At lower confining pressures, shear localization occurred in brittle faulting regime. Through transitional regime, the deformation switched to cataclastic flow regime at higher confining pressure. Specifically in the cataclastic regime, the (dry and wet) Tavel and dry Indiana failed by distributed cataclastic flow, while in contrast, wet Indiana failed as compaction localization. My results demonstrate that different failure modes and mechanical behaviors under different deformation regimes and water saturation are fundamental prior to any geophysical application in porous carbonates. The third part aimed to focus on investigating compaction on quartz aggregate starting at low (MPa) using X-ray diffraction. We report the diffraction peak evolution of quartz with increasing

  20. Mineralogy, provenance, and diagenesis of a potassic basaltic sandstone on Mars: CheMin X‐ray diffraction of the Windjana sample (Kimberley area, Gale Crater)

    Science.gov (United States)

    Bish, David L.; Vaniman, David T.; Chipera, Steve J.; Blake, David F.; Ming, Doug W.; Morris, Richard V.; Bristow, Thomas F.; Morrison, Shaunna M.; Baker, Michael B.; Rampe, Elizabeth B.; Downs, Robert T.; Filiberto, Justin; Glazner, Allen F.; Gellert, Ralf; Thompson, Lucy M.; Schmidt, Mariek E.; Le Deit, Laetitia; Wiens, Roger C.; McAdam, Amy C.; Achilles, Cherie N.; Edgett, Kenneth S.; Farmer, Jack D.; Fendrich, Kim V.; Grotzinger, John P.; Gupta, Sanjeev; Morookian, John Michael; Newcombe, Megan E.; Rice, Melissa S.; Spray, John G.; Stolper, Edward M.; Sumner, Dawn Y.; Vasavada, Ashwin R.; Yen, Albert S.

    2016-01-01

    Abstract The Windjana drill sample, a sandstone of the Dillinger member (Kimberley formation, Gale Crater, Mars), was analyzed by CheMin X‐ray diffraction (XRD) in the MSL Curiosity rover. From Rietveld refinements of its XRD pattern, Windjana contains the following: sanidine (21% weight, ~Or95); augite (20%); magnetite (12%); pigeonite; olivine; plagioclase; amorphous and smectitic material (~25%); and percent levels of others including ilmenite, fluorapatite, and bassanite. From mass balance on the Alpha Proton X‐ray Spectrometer (APXS) chemical analysis, the amorphous material is Fe rich with nearly no other cations—like ferrihydrite. The Windjana sample shows little alteration and was likely cemented by its magnetite and ferrihydrite. From ChemCam Laser‐Induced Breakdown Spectrometer (LIBS) chemical analyses, Windjana is representative of the Dillinger and Mount Remarkable members of the Kimberley formation. LIBS data suggest that the Kimberley sediments include at least three chemical components. The most K‐rich targets have 5.6% K2O, ~1.8 times that of Windjana, implying a sediment component with >40% sanidine, e.g., a trachyte. A second component is rich in mafic minerals, with little feldspar (like a shergottite). A third component is richer in plagioclase and in Na2O, and is likely to be basaltic. The K‐rich sediment component is consistent with APXS and ChemCam observations of K‐rich rocks elsewhere in Gale Crater. The source of this sediment component was likely volcanic. The presence of sediment from many igneous sources, in concert with Curiosity's identifications of other igneous materials (e.g., mugearite), implies that the northern rim of Gale Crater exposes a diverse igneous complex, at least as diverse as that found in similar‐age terranes on Earth. PMID:27134806

  1. Mineralogy, provenance, and diagenesis of a potassic basaltic sandstone on Mars: CheMin X-ray diffraction of the Windjana sample (Kimberley area, Gale Crater)

    Science.gov (United States)

    Treiman, Allan H.; Bish, David L.; Vaniman, David T.; Chipera, Steve J.; Blake, David F.; Ming, Doug W.; Morris, Richard V.; Bristow, Thomas F.; Morrison, Shaunna M.; Baker, Michael B.; Rampe, Elizabeth B.; Downs, Robert T.; Filiberto, Justin; Glazner, Allen F.; Gellert, Ralf; Thompson, Lucy M.; Schmidt, Mariek E.; Le Deit, Laetitia; Wiens, Roger C.; McAdam, Amy C.; Achilles, Cherie N.; Edgett, Kenneth S.; Farmer, Jack D.; Fendrich, Kim V.; Grotzinger, John P.; Gupta, Sanjeev; Morookian, John Michael; Newcombe, Megan E.; Rice, Melissa S.; Spray, John G.; Stolper, Edward M.; Sumner, Dawn Y.; Vasavada, Ashwin R.; Yen, Albert S.

    2016-01-01

    The Windjana drill sample, a sandstone of the Dillinger member (Kimberley formation, Gale Crater, Mars), was analyzed by CheMin X-ray diffraction (XRD) in the MSL Curiosity rover. From Rietveld refinements of its XRD pattern, Windjana contains the following: sanidine (21% weight, ~Or95); augite (20%); magnetite (12%); pigeonite; olivine; plagioclase; amorphous and smectitic material (~25%); and percent levels of others including ilmenite, fluorapatite, and bassanite. From mass balance on the Alpha Proton X-ray Spectrometer (APXS) chemical analysis, the amorphous material is Fe rich with nearly no other cations—like ferrihydrite. The Windjana sample shows little alteration and was likely cemented by its magnetite and ferrihydrite. From ChemCam Laser-Induced Breakdown Spectrometer (LIBS) chemical analyses, Windjana is representative of the Dillinger and Mount Remarkable members of the Kimberley formation. LIBS data suggest that the Kimberley sediments include at least three chemical components. The most K-rich targets have 5.6% K2O, ~1.8 times that of Windjana, implying a sediment component with >40% sanidine, e.g., a trachyte. A second component is rich in mafic minerals, with little feldspar (like a shergottite). A third component is richer in plagioclase and in Na2O, and is likely to be basaltic. The K-rich sediment component is consistent with APXS and ChemCam observations of K-rich rocks elsewhere in Gale Crater. The source of this sediment component was likely volcanic. The presence of sediment from many igneous sources, in concert with Curiosity's identifications of other igneous materials (e.g., mugearite), implies that the northern rim of Gale Crater exposes a diverse igneous complex, at least as diverse as that found in similar-age terranes on Earth.

  2. Influence of pore structures on the mechanical behavior of low-permeability sandstones:numerical reconstruction and analysis

    Institute of Scientific and Technical Information of China (English)

    Jiangtao Zheng; Yang Ju; Xi Zhao

    2014-01-01

    The research of rock properties based on its inherent microscopic to mesoscopic porous structure has drawn great attention for its potential in predicting the macroscopic behavior of rocks. An accurate reconstruction of the three-dimensional porous structure is a premise for the related studies of hydraulic and mechanical properties of rocks, such as the transport properties and mechanical responses under pressures. In this paper, we present a computer procedure for reconstructing the 3D porous structure of low-permeability sandstone. Two large-size 3D models are reconstructed based on the information of a reference model which is established from computed tomography (CT) images. A self-developed finite element method is applied to analyze the nonlinear mechanical behavior of the sandstone based on its reconstructed model and to compare the results with those based on the reference model. The good consistency of the obtained mechanical responses indicates the potential of using reconstruction models to predict the influences of porous structure on the mechanical properties of low-permeability sandstone.

  3. Consistent model driven architecture

    Science.gov (United States)

    Niepostyn, Stanisław J.

    2015-09-01

    The goal of the MDA is to produce software systems from abstract models in a way where human interaction is restricted to a minimum. These abstract models are based on the UML language. However, the semantics of UML models is defined in a natural language. Subsequently the verification of consistency of these diagrams is needed in order to identify errors in requirements at the early stage of the development process. The verification of consistency is difficult due to a semi-formal nature of UML diagrams. We propose automatic verification of consistency of the series of UML diagrams originating from abstract models implemented with our consistency rules. This Consistent Model Driven Architecture approach enables us to generate automatically complete workflow applications from consistent and complete models developed from abstract models (e.g. Business Context Diagram). Therefore, our method can be used to check practicability (feasibility) of software architecture models.

  4. No consistent bimetric gravity?

    CERN Document Server

    Deser, S; Waldron, A

    2013-01-01

    We discuss the prospects for a consistent, nonlinear, partially massless (PM), gauge symmetry of bimetric gravity (BMG). Just as for single metric massive gravity, ultimate consistency of both BMG and the putative PM BMG theory relies crucially on this gauge symmetry. We argue, however, that it does not exist.

  5. Dynamic fluid connectivity during steady-state multiphase flow in a sandstone

    Science.gov (United States)

    Reynolds, Catriona A.; Menke, Hannah; Andrew, Matthew; Blunt, Martin J.; Krevor, Samuel

    2017-08-01

    The current conceptual picture of steady-state multiphase Darcy flow in porous media is that the fluid phases organize into separate flow pathways with stable interfaces. Here we demonstrate a previously unobserved type of steady-state flow behavior, which we term “dynamic connectivity,” using fast pore-scale X-ray imaging. We image the flow of N2 and brine through a permeable sandstone at subsurface reservoir conditions, and low capillary numbers, and at constant fluid saturation. At any instant, the network of pores filled with the nonwetting phase is not necessarily connected. Flow occurs along pathways that periodically reconnect, like cars controlled by traffic lights. This behavior is consistent with an energy balance, where some of the energy of the injected fluids is sporadically converted to create new interfaces.

  6. Imaging the Morrow A Sandstone Using Shear Wave VSP Data, Postle Field, Oklahoma

    Directory of Open Access Journals (Sweden)

    Naser Tamimi

    2012-01-01

    potential to enhance shear wave imaging of the thin heterogeneous Morrow A sandstone at Postle Field. The zero-offset VSP results confirm the advantages of shear wave over compressional wave in imaging the Morrow A sandstone. Also, the final shear wave VSP image shows that, applying the proposed processing flow, we are able to image the Morrow A sandstone where the thickness is as thin as 8.5 m.

  7. Petrology and stratigraphy of Paleogene nonmarine sandstones, Cascade Range, Washington

    Science.gov (United States)

    Frizzell, Virgil A.

    1979-01-01

    The Cascade Range of Washington north of 47? latitude is composed of probable Paleozoic and Mesozoic metamorphic rocks and Mesozoic and Tertiary plutonic rocks. Several Paleogene nonmarine arkosic sandstone units fringe and in part occur within the complex crystalline core. The early to middle Eocene Chuckanut Formation is present on the west side of the crystalline core in the western foothills of the Cascades. The early to middle Eocene Swauk Formation partially encircles the Mt. Stuart massif of the central Cascades. In the western foothills of the Cascades, between the main body of Chuckanut Formation near Bellingham and the main outcrop area of the Swauk Formation south of Mt. Stuart, many smaller bodies of arkosic sandstone have variously been referred to either the Swauk or Chuckanut Formations. The early Eocene Manastash Formation occurs locally in an area south of the Yakima River. The middle to late Eocene Chumstick Formation is mostly confined to the Chiwaukum graben within the crystalline core and is separated from the Swauk Formation on the southwest by the Leavenworth Fault. The Oligocene Wenatchee Formation unconformably over lies the Chumstick Formation near Wenatchee. The middle to late Eocene Roslyn Formation crops out north of the Yakima River and is underlain by the Teanaway Basalt which separates the Roslyn from the older Swauk Formation. The middle Eocene to early Oligocene Naches Formation forms a north-trending body that crosses the Yakima River and is in fault contact with both the Swauk and Manastash Formations. The middle to late Eocene Puget Group underlies the Quaternary deposits of the Puget Lowland southeast of Seattle on the western flank of the Cascades. The various formations are all composed predominantly of fine- to medium-grained sandstones with lesser amounts of interbedded shale, conglomerate and coal. Compositionally, the units are predominantly either feldspathic or litho-feldspathic subquartzose sandstones. Volcanic rocks

  8. Time-dependent compaction band formation in sandstone

    Science.gov (United States)

    Heap, Michael J.; Brantut, Nicolas; Baud, Patrick; Meredith, Philip G.

    2015-07-01

    Compaction bands in sandstone are laterally extensive planar deformation features that are characterized by lower porosity and permeability than the surrounding host rock. As a result, this form of localization has important implications for both strain partitioning and fluid flow in the Earth's upper crust. To better understand the time dependency of compaction band growth, we performed triaxial deformation experiments on water-saturated Bleurswiller sandstone (initial porosity = 0.24) under constant stress (creep) conditions in the compactant regime. Our experiments show that inelastic strain accumulates at a constant stress in the compactant regime, manifest as compaction bands. While creep in the dilatant regime is characterized by an increase in porosity and, ultimately, an acceleration in axial strain rate to shear failure, compaction creep is characterized by a reduction in porosity and a gradual deceleration in axial strain rate. The global decrease in the rates of axial strain, acoustic emission energy, and porosity change during creep compaction is punctuated at intervals by higher rate excursions, interpreted as the formation of compaction bands. The growth rate of compaction bands formed during creep is lower as the applied differential stress, and hence, background creep strain rate, is decreased. However, the inelastic strain associated with the growth of a compaction band remains constant over strain rates spanning several orders of magnitude (from 10-8 to 10-5 s-1). We find that despite the large differences in strain rate and growth rate (from both creep and constant strain rate experiments), the characteristics (geometry and thickness) of the compaction bands remain essentially the same. Several lines of evidence, notably the similarity between the differential stress dependence of creep strain rate in the dilatant and compactant regimes, suggest that as for dilatant creep, subcritical stress corrosion cracking is the mechanism responsible for

  9. Diagenesis of shallowly buried cratonic sandstones, southwest Sinai, Egypt

    Science.gov (United States)

    Salem, Alaa M. K.; Abdel-Wahab, Antar; McBride, Earle F.

    1998-08-01

    In spite of their age, quartzose and feldspathic Lower Carboniferous sandstones deposited on the Arabian shield in western Sinai remain friable and porous (average of 19%, maximum of 25%) except for strongly cemented ferricretes and silcretes. These fluvial and shallow-marine sandstones were not buried more than 1.5 km until Late Cretaceous and younger time, when the deepest rocks reached 2.5 km. Owing to shallow burial depths and episodic exposure, meteoric water dominated the pore system for most of geologic time: iron oxides had multiple diagenetic stages and yield Carboniferous and Late Cretaceous paleomagnetic signatures, and oxygen isotopic data for authigenic quartz, sparry calcite, and kaolinite yield meteoric signatures. The most significant diagenetic changes were: (1) cementation by iron oxide that locally reaches 40% in groundwater ferricretes; (2) reduction in porosity to 19% from an assumed original porosity 45% (19% porosity was lost by compaction and 7% by cementation); (3) generation of diagenetic quartzarenites by the loss of 7% detrital feldspar by kaolinization and dissolution; and (4) development of three thin mature silcretes apparently by thermal groundwaters. Some outcrop samples have halite and gypsum cements of young but uncertain origin: recycled from topographically higher younger rocks or from aerosols? Mature silcretes are strongly cemented by microcrystalline quartz, multiply zoned syntaxial quartz, and, originally, minor opal. Quartz overgrowths in most sandstones average only 2.2%, but display a variety of textures and in places overprint isopachous opal (now dissolved) grain coats. These features have more in common with incipient silcrete cement than normal burial quartz cement. Most silica was imported in groundwater.

  10. Population genetic structure of a sandstone specialist and a generalist heath species at two levels of sandstone patchiness across the Strait of Gibraltar.

    Science.gov (United States)

    Gil-López, Manuel Jesús; Segarra-Moragues, José Gabriel; Ojeda, Fernando

    2014-01-01

    Many habitat specialist species are originally composed of small, discontinuous populations because their habitats are naturally fragmented or patchy. They may have suffered the long-term effects of natural patchiness. Mediterranean heathlands, a representative habitat in the Strait of Gibraltar region, are associated with nutrient-poor, acidic sandstone soils. Sandstone soil patches in the African side of the Strait (Tangier) are, in general, smaller and more scattered than in the European side (Algeciras). In this study, we analyze the effect of this sandstone patchiness on the population genetic diversity and structure of two Erica species from these Mediterranean heathlands that differ in their edaphic specificity, E. australis, sandstone specialist, and E. arborea, generalist. Average levels of within-population genetic diversity and gene flow between populations were significantly lower in Tangier (high sandstone patchiness) than in Algeciras (low patchiness) for the sandstone specialist, whereas no differences between both sides of the Strait were detected in the edaphic generalist. Since most endemic species in Mediterranean heathlands of the Strait of Gibraltar are sandstone specialists, these results highlight an increased vulnerability to loss of genetic diversity and local extinction of the heathland endemic flora in the Tangier side of the Strait of Gibraltar.

  11. Population genetic structure of a sandstone specialist and a generalist heath species at two levels of sandstone patchiness across the Strait of Gibraltar.

    Directory of Open Access Journals (Sweden)

    Manuel Jesús Gil-López

    Full Text Available Many habitat specialist species are originally composed of small, discontinuous populations because their habitats are naturally fragmented or patchy. They may have suffered the long-term effects of natural patchiness. Mediterranean heathlands, a representative habitat in the Strait of Gibraltar region, are associated with nutrient-poor, acidic sandstone soils. Sandstone soil patches in the African side of the Strait (Tangier are, in general, smaller and more scattered than in the European side (Algeciras. In this study, we analyze the effect of this sandstone patchiness on the population genetic diversity and structure of two Erica species from these Mediterranean heathlands that differ in their edaphic specificity, E. australis, sandstone specialist, and E. arborea, generalist. Average levels of within-population genetic diversity and gene flow between populations were significantly lower in Tangier (high sandstone patchiness than in Algeciras (low patchiness for the sandstone specialist, whereas no differences between both sides of the Strait were detected in the edaphic generalist. Since most endemic species in Mediterranean heathlands of the Strait of Gibraltar are sandstone specialists, these results highlight an increased vulnerability to loss of genetic diversity and local extinction of the heathland endemic flora in the Tangier side of the Strait of Gibraltar.

  12. Prizes for consistency

    Energy Technology Data Exchange (ETDEWEB)

    Hiscock, S.

    1986-07-01

    The importance of consistency in coal quality has become of increasing significance recently, with the current trend towards using coal from a range of sources. A significant development has been the swing in responsibilities for coal quality. The increasing demand for consistency in quality has led to a re-examination of where in the trade and transport chain the quality should be assessed and where further upgrading of inspection and preparation facilities are required. Changes are in progress throughout the whole coal transport chain which will improve consistency of delivered coal quality. These include installation of beneficiation plant at coal mines, export terminals, and on the premises of end users. It is suggested that one of the keys to success for the coal industry will be the ability to provide coal of a consistent quality.

  13. Consistent sets contradict

    CERN Document Server

    Kent, A

    1996-01-01

    In the consistent histories formulation of quantum theory, the probabilistic predictions and retrodictions made from observed data depend on the choice of a consistent set. We show that this freedom allows the formalism to retrodict several contradictory propositions which correspond to orthogonal commuting projections and which all have probability one. We also show that the formalism makes contradictory probability one predictions when applied to generalised time-symmetric quantum mechanics.

  14. Subsurface petroleum geology of Santa Rosa sandstone (Triassic), northeast New Mexico

    Science.gov (United States)

    Broadhead, R. F.

    The Santa Rose Sandstone (Triassic) occurs at depths of less than 2,000 ft over most of northeast New Mexico. Two major petroleum accumulations are known to exist in it. These outcrops of oil impregnated sandstone are known as the Santa Rosa tar sands. The oil in the tar sands is viscous and heavy. The other known petroleum accumulation is a pool of heavy oil that occurs at depths of 400 ft to 800 ft in northeast Guadalupe County. Attempts are being made to recover the heavy oil with steamflooding in two small pilot fields. The lower and upper sandstone units are blanket deposits composed mostly of fine to medium grained porous sandstones and minor red siliciclastic mudstones. The middle mudstone unit is a blanket deposit composed chiefly of red siliciclastic mudstones and minor lenticular sandstones. Stratigraphic and petrographic studies indicate that good reservoirs are widespread in the lower and upper sandstone unit. The blanket geometry of the lower and upper sandstone units indicates that structure probably plays an important or even dominant role in the trapping of any undiscovered hydrocarbons in the Santa Rosa. Oil proximal to the outcrop belt of the Santa Rosa Sandstone has probably been flushed by recently recharged fresh ground water. Although the source of the oil in Santa Rosa Sandstone is not definitely known, geochemical studies point to the San Andres Formation (Permian) or possibly Pennsylanian rocks.

  15. Greybull Sandstone Petroleum Potential on the Crow Indian Reservation, South-Central Montana

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, David A.

    2002-05-13

    The focus of this project was to explore for stratigraphic traps that may be present in valley-fill sandstone at the top of the Lower Cretaceous Kootenai Formation. This sandstone interval, generally known as the Greybull Sandstone, has been identified along the western edge of the reservation and is a known oil and gas reservoir in the surrounding region. The Greybull Sandstone was chosen as the focus of this research because it is an excellent, well-documented, productive reservoir in adjacent areas, such as Elk Basin; Mosser Dome field, a few miles northwest of the reservation; and several other oil and gas fields in the northern portion of the Bighorn Basin.

  16. Water Vapor Diffusion and Adsorption of Sandstones: Influence of Rock Texture and Composition

    Directory of Open Access Journals (Sweden)

    Martin Keppert

    2016-01-01

    Full Text Available The term sandstone is used for wide range of rocks containing quartz clasts which can be cemented by secondary precipitated quartz or calcite; moreover the space between clasts can be filled by matrix. These facts result in existence of numerous rocks having highly various properties. Sandstones have been used as construction materials due to their good accessibility and workability. Since most of sandstones are porous, water vapor can penetrate through sandstone constructions. The rate of water vapor diffusion, as well as the vapor sorption isotherm, was determined for range of sandstone types. The diffusion resistance factor was found to be dependent on the total porosity of sandstone but the sorption behavior was strongly influenced by nature of the particular sandstone; the specific surface area of stone and presence of clay matrix are determining its sorption isotherm. The published data enable estimating (i diffusion resistance factor of a sandstone via knowledge of its total porosity and (ii the sorption isotherm via knowledge of the stone’s nature and specific surface area. This approach can significantly reduce the time necessary to acquire vapor-related properties of a sandstone.

  17. Mechanical properties and failure characteristics of fractured sandstone with grouting and anchorage

    Institute of Scientific and Technical Information of China (English)

    Zong Yijiang; Han Lijun; Qu Tao; Yang Shengqi

    2014-01-01

    Based on uniaxial compression experimental results on fractured sandstone with grouting and anchorage, we studied the strength and deformation properties, the failure model, crack formation and evolution laws of fractured sandstone under different conditions of anchorage. The experimental results show that the strength and elastic modulus of fractured sandstone with different fracture angles are sig-nificantly lower than those of intact sandstone. Compared with the fractured samples without anchorage, the peak strength, residual strength, peak and ultimate axial strain of fractured sandstone under different anchorage increase by 64.5-320.0%, 62.8-493.0%, and 31.6-181.4%, respectively. The number of bolts and degree of pre-stress has certain effects on the peak strength and failure model of fractured sandstone. The peak strength of fractured sandstone under different anchorage increases to some extent, and the failure model of fractured sandstone also transforms from tensile failure to tensile-shear mixed failure with the number of bolts. The pre-stress can restrain the formation and evolution process of tensile cracks, delay the failure process of fractured sandstone under anchorage and impel the transformation of failure model from brittle failure to plastic failure.

  18. Magnetic Titanohematite Minerals in Uranium-Bearing Sandstones

    Science.gov (United States)

    Reynolds, Richard L.

    1977-01-01

    Detrital grains of the rhombohedral ilmenite (FeT1O3)--hematite (Fe2O3) solid solution series (titanohematites) have been identified by thermomagnetic, reflection microscopic, and X-ray diffraction analysis in six uranium-bearing sandstones in the western United States. Many of the titanohematites are ferrimagnetic and have Curie temperatures ranging from about 70 Deg C to 220 Deg C. Magnetic titanohematite is commonly more abundant than magnetite in many samples and, therefore, should be considered as a major source of the permanent magnetization in these units.

  19. Diagenesis, provenance and depositional environments of the Bunter Sandstone Formation

    DEFF Research Database (Denmark)

    Olivarius, Mette; Weibel, Rikke; Friis, Henrik

    The Bunter Sandstone Formation in the northern North German Basin has large geothermal potential with high porosity and permeability (generally >15% and >100 mD, respectively) and with pore fluid temperatures that are adequate for geothermal energy production (c. 55–60˚C). A combined investigation...... of diagenesis, provenance and depositional environments is used to identify the reservoir rocks that possess the best quality. This is accomplished by integrating various methods including: seismic reflection data, sedimentological description of cores, mineral quantification by point counting, measurement...

  20. Reservoir characterization of Pennsylvanian sandstone reservoirs. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kelkar, M.

    1995-02-01

    This final report summarizes the progress during the three years of a project on Reservoir Characterization of Pennsylvanian Sandstone Reservoirs. The report is divided into three sections: (i) reservoir description; (ii) scale-up procedures; (iii) outcrop investigation. The first section describes the methods by which a reservoir can be described in three dimensions. The next step in reservoir description is to scale up reservoir properties for flow simulation. The second section addresses the issue of scale-up of reservoir properties once the spatial descriptions of properties are created. The last section describes the investigation of an outcrop.

  1. Initiation of acoustic emission in fluid-saturated sandstone samples

    Science.gov (United States)

    Lapshin, V. B.; Patonin, A. V.; Ponomarev, A. V.; Potanina, M. G.; Smirnov, V. B.; Stroganova, S. M.

    2016-07-01

    A rock behavior experiment with uniaxial compression revealed the effect of acoustic activity in loaded fluid-saturated Berea sandstone samples in response to an electric current. It is established that it is substantially intensified in periods of the current impact and decreases after its cut-off. The current impact also results in a growth of radial deformation indicating an increase in the sample volume. The effect of acoustic activation increases in response to increased heat emitted by the electric current during its flow through the sample, which allows the discovered effect to be explained by initiation of its destruction due to thermal expansion of the fluid in rock interstices and fissures.

  2. Injection of CO2 with H2S and SO2 and Subsequent Mineral Trapping in Sandstone-Shale Formation

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Tianfu; Apps, John A.; Pruess, Karsten; Yamamoto, Hajime

    2004-09-07

    Carbon dioxide (CO{sub 2}) injection into deep geologic formations can potentially reduce atmospheric emissions of greenhouse gases. Sequestering less-pure CO{sub 2} waste streams (containing H{sub 2}S and/or SO{sub 2}) would be less expensive or would require less energy than separating CO{sub 2} from flue gas or a coal gasification process. The long-term interaction of these injected acid gases with shale-confining layers of a sandstone injection zone has not been well investigated. We therefore have developed a conceptual model of injection of CO{sub 2} with H{sub 2}S and/or SO{sub 2} into a sandstone-shale sequence, using hydrogeologic properties and mineral compositions commonly encountered in Gulf Coast sediments of the United States. We have performed numerical simulations of a 1-D radial well region considering sandstone alone and a 2-D model using a sandstone-shale sequence under acid-gas injection conditions. Results indicate that shale plays a limited role in mineral alteration and sequestration of gases within a sandstone horizon for short time periods (10,000 years in present simulations). The co-injection of SO{sub 2} results in different pH distribution, mineral alteration patterns, and CO{sub 2} mineral sequestration than the co-injection of H{sub 2}S or injection of CO{sub 2} alone. Simulations generate a zonal distribution of mineral alteration and formation of carbon and sulfur trapping minerals that depends on the pH distribution. The co-injection of SO{sub 2} results in a larger and stronger acidified zone close to the well. Precipitation of carbon trapping minerals occurs within the higher pH regions beyond the acidified zones. In contrast, sulfur trapping minerals are stable at low pH ranges (below 5) within the front of the acidified zone. Corrosion and well abandonment due to the co-injection of SO{sub 2} could be important issues. Significant CO{sub 2} is sequestered in ankerite and dawsonite, and some in siderite. The CO{sub 2} mineral

  3. Measuring the zeta potential. The relationships with sandstone fineness

    Directory of Open Access Journals (Sweden)

    de Luxán, M. P.

    1989-09-01

    Full Text Available The application of the zeta potential technique in the area of construction materials and Portland cement is quite recent. The initial research work involved the study of cement suspensions or suspensions of one of the components of cement, such as alite, tricalcium alumínate, in the presence of additives and, more specifically, superplasticizers. The studies of this sort were extended with the mixing of active additions into cement (fly ashes, etc.. The present study discusses the application of siliceous materials (sandstone as a basis of the research into the behaviour of sandstone mortars containing repair products.

    La aplicación de la técnica del potencial zeta en el campo de los materiales de construcción y del cemento portland es muy reciente. Las primeras investigaciones se refieren al estudio de suspensiones de cemento o de alguno de sus compuestos que lo forman como alita, aluminato tricálcico, en presencia de aditivos y, más concretamente, de superfluidificantes. Con la incorporación de adiciones activas al cemento (cenizas volantes,... se amplían los estudios de este tipo de cementos. En este trabajo se considera la aplicación a los materiales silíceos (arenisca como base para la investigación del comportamiento de los morteros de arenisca conteniendo productos de reparación.

  4. The Creep Properties of Fine Sandstone under Uniaxial Tensile Stress

    Directory of Open Access Journals (Sweden)

    Jiang Haifei

    2015-09-01

    Full Text Available A graduated uniaxial direct tensile creep test for fine sandstone is conducted by adopting a custom-designed direct tensile test device for rock. The experiment shows that the tensile creep of fine sandstone has similar creep curve patterns to those of compression creep, while the ratios of the creep strain to the total strain obtained in the tensile tests are substantially higher than those obtained for similar compression tests, which indicates that the creep ability of rock in the tensile process is higher than that in the uniaxial compression process. Based on the elastic modulus in the approximately linear portion of the obtained isochronous stress-strain curves of the tensile creep, the time dependence of the elasticity modulus for the Kelvin model is evaluated, and a revised generalized Kelvin model is obtained by substitution into the generalized Kelvin model. A new viscousplastic model is proposed to describe the accelerated creep properties, and this model is combined in series with the revised generalized Kelvin model to form a new nonlinear viscoelastic-plastic creep model that can describe the properties of attenuation creep, steady creep, and accelerated creep. Comparison of the test and theoretical curves demonstrates that they are nearly identical, which verifies the performance of the model.

  5. Water coning mechanism in Tarim fractured sandstone gas reservoirs

    Institute of Scientific and Technical Information of China (English)

    沈伟军; 刘晓华; 李熙喆; 陆家亮

    2015-01-01

    The problem of water coning into the Tarim fractured sandstone gas reservoirs becomes one of the major concerns in terms of productivity, increased operating costs and environmental effects. Water coning is a phenomenon caused by the imbalance between gravity and viscous forces around the completion interval. There are several controllable and uncontrollable parameters influencing this problem. In order to simulate the key parameters affecting the water coning phenomenon, a model was developed to represent a single well with an underlying aquifer using the fractured sandstone gas reservoir data of the A-Well in Dina gas fields. The parametric study was performed by varying six properties individually over a representative range. The results show that matrix permeability, well penetration (especially fracture permeability), vertical-to-horizontal permeability ratio, aquifer size and gas production rate have considerable effect on water coning in the fractured gas reservoirs. Thus, investigation of the effective parameters is necessary to understand the mechanism of water coning phenomenon. Simulation of the problem helps to optimize the conditions in which the breakthrough of water coning is delayed.

  6. Selected trace and minor elements in sandstones from Paraguay

    Energy Technology Data Exchange (ETDEWEB)

    Facetti-Masulli, J.F.; Gonzalez, E. [Hydroconsult SRL, Asuncion (Paraguay); Kump, P. [J. Stefan Inst., Ljubljana (Slovenia)

    2010-07-01

    Selected trace and minor elements analyzed by XRF in sandstone samples were Rb-Sr-Zr-Nb-Ba-La-Ce-Nd as well as Ti-Mn-Fe with which they are often correlated. Refractory elements like REE are considered useful indicators of geochemical processes and, in this case, of provenance. Usually they maintain their original relationships and are transferred almost directly into sediments. The values here found, absolute and normalized, show correlations among the samples, allowing the establishment of their origin. Most of them in the spidergram patterns display positive spikes of Zr, and negative anomalies at Nb, Sr, Ti: differences in their height/depth could be in relation with the different Series or Formations. Strikingly, spidergrams of samples collected from the Patino Formation show marked negative anomalies interalia of Ba, as well as positive spikes of Nb and Zr, very similar to those found in magmatic specimens from Misiones, Carapegua-Acahay and Alto Paraguay Province and quite different from the other analyzed samples. In addition a remarkable presence of Precambrian signatures were found in the analyzed sandstones from the Paleozoic. (orig.)

  7. Acoustic Emission Parameters of Three Gorges Sandstone during Shear Failure

    Directory of Open Access Journals (Sweden)

    Xu Jiang

    2016-12-01

    Full Text Available In this paper, an experimental investigation of sandstone samples from the Three Gorges during shear failure was conducted using acoustic emission (AE and direct shear tests. The AE count rate, cumulative AE count, AE energy, and amplitude of the sandstone samples were determined. Then, the relationships among the AE signals and shearing behaviors of the samples were analyzed in order to detect micro-crack initiation and propagation and reflect shear failure. The results indicated that both the shear strength and displacement exhibited a logarithmic relationship with the displacement rate at peak levels of stress. In addition, the various characteristics of the AE signals were apparent in various situations. The AE signals corresponded with the shear stress under different displacement rates. As the displacement rate increased, the amount of accumulative damage to each specimen decreased, while the AE energy peaked earlier and more significantly. The cumulative AE count primarily increased during the post-peak period. Furthermore, the AE count rate and amplitude exhibited two peaks during the peak shear stress period due to crack coalescence and rock bridge breakage. These isolated cracks later formed larger fractures and eventually caused ruptures.

  8. Core-log integration for a Saudi Arabian sandstone reservoir

    Energy Technology Data Exchange (ETDEWEB)

    Saha, S.; Al-Kaabi, A.U.; Amabeoku, M.O.; Al-Fossail, K.

    1995-10-01

    For a detailed characterization of a reservoir, core-log integration is essential. In this paper, data integration from logs and cores of a Saudi Arabian sandstone reservoir is discussed with particular attention to effects of clay on resistivity logs and water saturation. There are four sources of data, namely, core resistivity measurement, clay study from cores (XRD, CEC), spectral core gamma ray, and well logs. In order to generate continuous cation exchange capacity (CEC) with depth, spectral gamma ray measurements (both from core and downhole log) and CEC from cores and correlated. Q{sub v} (CEC per unit pore volume) values are calculated utilizing only well logs by applying Waxman-Smits equation in water bearing zone. Log derived Q{sub v} values from water zone were then correlated with porosity to generate Q{sub v} values in the oil column and compared with core derived Z{sub v}. Finally, data from well logs (porosity, resistivity and Q{sub v}) and cores (resistivity parameters m, n, and Q{sub v}) were integrated for more accurate water saturation calculation. The core-log correlation can be applied to other wells avoiding expensive core analysis, and the technique developed in this project can be used in other sandstone reservoirs.

  9. Distribution characteristics and petroleum geological significance of the Silurian asphaltic sandstones in Tarim Basin

    Institute of Scientific and Technical Information of China (English)

    ZHANG; Jun; PANG; Xiongqi; LIU; Luofu; JIANG; Zhenxue; LIU

    2004-01-01

    The Tarim Basin is a typical superimposed basin in which there have occurred multiphase adjustment and destruction of the reservoirs. The widely distributed asphaltic sandstones of the Silurian are the very product after destruction of the reservoirs. Studies show that the Silurian asphaltic sandstones distributed in both the middle and western parts on the basin are controlled chiefly by the Caledonian oil source area and by the Tazhong, Tabei and Bachu uplifts, whereas the distribution of the asphaltic sandstones on local structural belts is controlled by the reservoir's sedimentary system. Vertically, most of the asphaltic sandstones are under the regional caprock of red mudstones and the upper sandstone section of compact lithology. Due to the difference of hydrocarbon destruction in the early stage and the influence of hydrocarbon recharge in the late stage, the asphaltic sandstones and oil-bearing sandstones in the Tazhong area can be vertically divided into the upper and lower sections and they have an interactive distribution relationship as well. Asphaltic sandstones exist not only in intergranular pores but also inside the grains of sand and between the crevices, proving the destruction of early reservoirs due to uplifting. The existence of asphaltic sandstones over a large area reveals that the large-scale migration and accumulation and the subsequent destruction of hydrocarbons in the Craton area. The destruction caused a loss of the reserve resources of the Palaeozoic amounting to nearly 13.3 billion tons. Asphaltic sandstones formed after the destruction of oil and gas may serve as an effective caprock which is beneficial to accumulation of hydrocarbons and formation of the pool sealed by asphaltic sandstones in the later stage. The destruction of the early Silurian hydrocarbons depends on the stratigraphic burial depth. The deep part under the northern slope of Tazhong is an area favorable to search of undestroyed Silurian oil reservoirs.

  10. Network Consistent Data Association.

    Science.gov (United States)

    Chakraborty, Anirban; Das, Abir; Roy-Chowdhury, Amit K

    2016-09-01

    Existing data association techniques mostly focus on matching pairs of data-point sets and then repeating this process along space-time to achieve long term correspondences. However, in many problems such as person re-identification, a set of data-points may be observed at multiple spatio-temporal locations and/or by multiple agents in a network and simply combining the local pairwise association results between sets of data-points often leads to inconsistencies over the global space-time horizons. In this paper, we propose a Novel Network Consistent Data Association (NCDA) framework formulated as an optimization problem that not only maintains consistency in association results across the network, but also improves the pairwise data association accuracies. The proposed NCDA can be solved as a binary integer program leading to a globally optimal solution and is capable of handling the challenging data-association scenario where the number of data-points varies across different sets of instances in the network. We also present an online implementation of NCDA method that can dynamically associate new observations to already observed data-points in an iterative fashion, while maintaining network consistency. We have tested both the batch and the online NCDA in two application areas-person re-identification and spatio-temporal cell tracking and observed consistent and highly accurate data association results in all the cases.

  11. Water weakening during semibrittle flow and faulting of experimentally deformed quartz sandstone

    Science.gov (United States)

    Kanaya, T.; Hirth, G.

    2015-12-01

    Triaxial compression experiments were conducted on Fontainebleau sandstone at temperatures to 900°C and effective pressures to 175 MPa with varying water contents. Both yield and peak strengths associated with semibrittle faulting decrease linearly with an increase in intragranular water concentration (COH); COH is determined from infrared spectroscopy. Microstructural observations and the influence of strain rate, temperature, and COH on peak strength suggest that transient semibrittle flow is accommodated through cataclasis assisted by stress-corrosion microcracking. The roles of the experimental variables on the constitutive behavior are similar to those reported for subcritical cracking of quartz single crystals. At high COH, microstructural observations indicate an increase in the relative contribution of mm-scale distributed shear fractures (bands) to axial strain, reflecting a reduction in grain-scale fracture toughness. This is consistent with the inference that highly dissipative shear fractures lead to the observed reduction in strength at high COH. Stress vs. strain rate data for transient semibrittle flow show temperature-dependent rate behavior, and are well fit by an exponential law with an activation enthalpy of 185 to 250 kJ/mol and Peierls stress of 2.5 to 7.5 GPa. Using these constraints, we infer that stress-corrosion cracking is rate-limited by the dislocation activity at crack tips. Correlation of microscale COH maps to microstructures suggests that intragranular water in the undeformed sandstone is associated mainly with clusters of fluid inclusions, resulting in a highly nonuniform distribution of COH both within and between grains. Axially deformed samples show a reduction in the median and variability of COH over a range of length scales. We observe that a local reduction in COH correlates with fluid inclusions that are decrepitated and crosscut by intragranular fractures. We conclude that intragranular fracture is the primary mechanism of

  12. Reporting consistently on CSR

    DEFF Research Database (Denmark)

    Thomsen, Christa; Nielsen, Anne Ellerup

    2006-01-01

    of a case study showing that companies use different and not necessarily consistent strategies for reporting on CSR. Finally, the implications for managerial practice are discussed. The chapter concludes by highlighting the value and awareness of the discourse and the discourse types adopted......This chapter first outlines theory and literature on CSR and Stakeholder Relations focusing on the different perspectives and the contextual and dynamic character of the CSR concept. CSR reporting challenges are discussed and a model of analysis is proposed. Next, our paper presents the results...... in the reporting material. By implementing consistent discourse strategies that interact according to a well-defined pattern or order, it is possible to communicate a strong social commitment on the one hand, and to take into consideration the expectations of the shareholders and the other stakeholders...

  13. A Magnetic Consistency Relation

    CERN Document Server

    Jain, Rajeev Kumar

    2012-01-01

    If cosmic magnetic fields are indeed produced during inflation, they are likely to be correlated with the scalar metric perturbations that are responsible for the Cosmic Microwave Background anisotropies and Large Scale Structure. Within an archetypical model of inflationary magnetogenesis, we show that there exists a new simple consistency relation for the non-Gaussian cross correlation function of the scalar metric perturbation with two powers of the magnetic field in the squeezed limit where the momentum of the metric perturbation vanishes. We emphasize that such a consistency relation turns out to be extremely useful to test some recent calculations in the literature. Apart from primordial non-Gaussianity induced by the curvature perturbations, such a cross correlation might provide a new observational probe of inflation and can in principle reveal the primordial nature of cosmic magnetic fields.

  14. Consistency in Distributed Systems

    OpenAIRE

    Kemme, Bettina; Ramalingam, Ganesan; Schiper, André; Shapiro, Marc; Vaswani, Kapil

    2013-01-01

    International audience; In distributed systems, there exists a fundamental trade-off between data consistency, availability, and the ability to tolerate failures. This trade-off has significant implications on the design of the entire distributed computing infrastructure such as storage systems, compilers and runtimes, application development frameworks and programming languages. Unfortunately, it also has significant, and poorly understood, implications for the designers and developers of en...

  15. Geometrically Consistent Mesh Modification

    KAUST Repository

    Bonito, A.

    2010-01-01

    A new paradigm of adaptivity is to execute refinement, coarsening, and smoothing of meshes on manifolds with incomplete information about their geometry and yet preserve position and curvature accuracy. We refer to this collectively as geometrically consistent (GC) mesh modification. We discuss the concept of discrete GC, show the failure of naive approaches, and propose and analyze a simple algorithm that is GC and accuracy preserving. © 2010 Society for Industrial and Applied Mathematics.

  16. Consistent wind Facilitates Vection

    Directory of Open Access Journals (Sweden)

    Masaki Ogawa

    2011-10-01

    Full Text Available We examined whether a consistent haptic cue suggesting forward self-motion facilitated vection. We used a fan with no blades (Dyson, AM01 providing a wind of constant strength and direction (wind speed was 6.37 m/s to the subjects' faces with the visual stimuli visible through the fan. We used an optic flow of expansion or contraction created by positioning 16,000 dots at random inside a simulated cube (length 20 m, and moving the observer's viewpoint to simulate forward or backward self-motion of 16 m/s. we tested three conditions for fan operation, which were normal operation, normal operation with the fan reversed (ie, no wind, and no operation (no wind and no sound. Vection was facilitated by the wind (shorter latency, longer duration and larger magnitude values with the expansion stimuli. The fan noise did not facilitate vection. The wind neither facilitated nor inhibited vection with the contraction stimuli, perhaps because a headwind is not consistent with backward self-motion. We speculate that the consistency between multi modalities is a key factor in facilitating vection.

  17. Desalination of salt damaged Obernkirchen sandstone by an applied DC field

    DEFF Research Database (Denmark)

    Matyščák, Ondřej; Ottosen, Lisbeth M.; Rörig-Dalgaard, Inge

    2014-01-01

    Soluble salts are considered as one of the most common causes for decay of building materials. In the present work, an electrokinetic method for desalination of sandstones from a historic warehouse was tested. The sandstones claddings were removed from the warehouse during a renovation action as ...

  18. Mechanism of Suppressing ASR Using Ground Reactive Sandstone Powders instead of Cement

    Institute of Scientific and Technical Information of China (English)

    LI Yang; HE Zhen; HU Shuguang

    2015-01-01

    In order to understand the effect of powders ground from reactive sandstone replacing cement on reducing or suppressing alkali-silica reaction (ASR), and to identify the mechanism of suppressing ASR by this powders, mortar and paste containing reactive sandstone powders of four replacement levels ranging from 10wt% to 40wt% and four specific surfaces areas ranging from 210 m2/kg to 860 m2/kg were studied. The experimental results showed that incorporation of 40wt%reactive sandstone powders could suppress ASR effectively except for mortar containing reactive sandstone powders with specific surface area of 610 m2/kg, which disagreed with the most results reported that the higher reactive powder specific surface area, the smaller ASR expansion. By means of flame photometry, Fourier transform infrared spectroscopy (FT-IR) and thermo gravimetric analysis (TG), the mechanism of reactive sandstone powders on reducing or suppressing ASR was soluble alkalis type of reactive sandstone powders and the competition of liberating and bonding alkali of cement paste containing reactive sandstone powders,when the ability of alkali bonding was greater than the ability of alkali liberation, ASR caused by reactive sandstone was supressed effectively.

  19. Diagenetic facies types and logging identification methods for low-permeability tight sandstone reservoirs:a case study on the 8th member of Xiashihezi Formation in Sulige gasfieid, Ordos Basin%低渗透致密砂岩储层成岩相类型及测井识别方法——以鄂尔多斯盆地苏里格气田下石盒子组8段为例

    Institute of Scientific and Technical Information of China (English)

    张海涛; 时卓; 石玉江; 王亮亮; 贺陆军

    2012-01-01

    Sulige gasfield in Ordos Basin is a typical tight gas reservoir. According to clastic constituents, diagenetic mineral assemblage,interstitial matter,and diagenesis types,et al,we identified 6 diagenetic faceis types in the 8 th member of Xiashihezi Formation ( He8 ) reservoir of Sulige gas field, including intergranular pore + strong solutional phase of volcanic material, intercrystal pore + solutional phase of volcanic material, intercrystal pore + solutional phase of debirs, intercrystal pore + cementation phase of quartz, hydromica cementation + weak solutional phase of debris and compaction + cementation tight phase. In addition,we analyzed the impacts of different digenesis on log responses. On the basis of these studies,a method for continuously and quantitatively identifying diagenetic facics was established by using gamma ray, interval transit time, density and deep lateral resistivity log data. Logging data of Well Z65 were processed with this method ,and a comparison with the thin section data and mercury injection data show that the results are accurate. Based on single well diagenetic facies identification, we defined the diagenetic face distribution in He8 reservoirs of Sulige gasfield. The central part of the gas field is dominated by intergranular pore + strong solutional phase of volcanic material and intercrystal pore + solutional phase of volcanic material, which are the favorable diagenetic faces belts.%鄂尔多斯盆地苏里格气田是低渗透致密砂岩气藏的典型代表,根据碎屑成分、成岩矿物组合、填隙物成分、成岩作用类型等特征,将苏里格气田盒8段储层划分为粒间孔+火山物质强溶蚀相、晶间孔+火山物质溶蚀相、晶间孔+岩屑溶蚀相、晶间孔+石英加大胶结相、水云母胶结+岩屑微溶蚀相和压实胶结致密成岩相6种成岩相类型,分析了不同成岩作用对测井响应的影响.在此基础上,通过自然伽马、声波时差、密度及深侧向测

  20. Sedimentology and reservoir heterogeneity of a valley-fill deposit-A field guide to the Dakota Sandstone of the San Rafael Swell, Utah

    Science.gov (United States)

    Kirschbaum, Mark A.; Schenk, Christopher J.

    2010-01-01

    Valley-fill deposits form a significant class of hydrocarbon reservoirs in many basins of the world. Maximizing recovery of fluids from these reservoirs requires an understanding of the scales of fluid-flow heterogeneity present within the valley-fill system. The Upper Cretaceous Dakota Sandstone in the San Rafael Swell, Utah contains well exposed, relatively accessible outcrops that allow a unique view of the external geometry and internal complexity of a set of rocks interpreted to be deposits of an incised valley fill. These units can be traced on outcrop for tens of miles, and individual sandstone bodies are exposed in three dimensions because of modern erosion in side canyons in a semiarid setting and by exhumation of the overlying, easily erodible Mancos Shale. The Dakota consists of two major units: (1) a lower amalgamated sandstone facies dominated by large-scale cross stratification with several individual sandstone bodies ranging in thickness from 8 to 28 feet, ranging in width from 115 to 150 feet, and having lengths as much as 5,000 feet, and (2) an upper facies composed of numerous mud-encased lenticular sandstones, dominated by ripple-scale lamination, in bedsets ranging in thickness from 5 to 12 feet. The lower facies is interpreted to be fluvial, probably of mainly braided stream origin that exhibits multiple incisions amalgamated into a complex sandstone body. The upper facies has lower energy, probably anastomosed channels encased within alluvial and coastal-plain floodplain sediments. The Dakota valley-fill complex has multiple scales of heterogeneity that could affect fluid flow in similar oil and gas subsurface reservoirs. The largest scale heterogeneity is at the formation level, where the valley-fill complex is sealed within overlying and underlying units. Within the valley-fill complex, there are heterogeneities between individual sandstone bodies, and at the smallest scale, internal heterogeneities within the bodies themselves. These

  1. On the origin and glacial transport of erratics of Jotnian sandstone in southwestern Finland

    Directory of Open Access Journals (Sweden)

    Donner, J.

    1996-12-01

    Full Text Available Late Proterozoic Jotnian sandstone erratics were transported during the last Quaternary glaciation from the source area in Satakunta at the coast of southwestern Finland and the bottom of the Bothnian Sea to the southeast as far as Estonia, Latvia and Russia. The frequencies of the sandstone erratics show that they were transported greater distances than indicators of other rocks in the southern parts of Finland. In addition, high frequencies in small areas, south of Salo and in Bromarv, indicate that there are or were small separate source areas of Jotnian sandstone outside the main area. This is supported by the distribution of erratics of Cambrian sandstone and Ordovician sedimentary rocks in the same area. The tracing of possible small occurrences of Jotnian sandstone or Palaeozoic rocks is, however, difficult in an area with numerous faults and fracture zones in the Precambrian bedrock, where the depressions are covered by thick Quaternary drift.

  2. Infanticide and moral consistency.

    Science.gov (United States)

    McMahan, Jeff

    2013-05-01

    The aim of this essay is to show that there are no easy options for those who are disturbed by the suggestion that infanticide may on occasion be morally permissible. The belief that infanticide is always wrong is doubtfully compatible with a range of widely shared moral beliefs that underlie various commonly accepted practices. Any set of beliefs about the morality of abortion, infanticide and the killing of animals that is internally consistent and even minimally credible will therefore unavoidably contain some beliefs that are counterintuitive.

  3. The Rucio Consistency Service

    CERN Document Server

    Serfon, Cedric; The ATLAS collaboration

    2016-01-01

    One of the biggest challenge with Large scale data management system is to ensure the consistency between the global file catalog and what is physically on all storage elements. To tackle this issue, the Rucio software which is used by the ATLAS Distributed Data Management system has been extended to automatically handle lost or unregistered files (aka Dark Data). This system automatically detects these inconsistencies and take actions like recovery or deletion of unneeded files in a central manner. In this talk, we will present this system, explain the internals and give some results.

  4. When is holography consistent?

    Energy Technology Data Exchange (ETDEWEB)

    McInnes, Brett, E-mail: matmcinn@nus.edu.sg [National University of Singapore (Singapore); Ong, Yen Chin, E-mail: yenchin.ong@nordita.org [Nordita, KTH Royal Institute of Technology and Stockholm University, Roslagstullsbacken 23, SE-106 91 Stockholm (Sweden)

    2015-09-15

    Holographic duality relates two radically different kinds of theory: one with gravity, one without. The very existence of such an equivalence imposes strong consistency conditions which are, in the nature of the case, hard to satisfy. Recently a particularly deep condition of this kind, relating the minimum of a probe brane action to a gravitational bulk action (in a Euclidean formulation), has been recognized; and the question arises as to the circumstances under which it, and its Lorentzian counterpart, is satisfied. We discuss the fact that there are physically interesting situations in which one or both versions might, in principle, not be satisfied. These arise in two distinct circumstances: first, when the bulk is not an Einstein manifold and, second, in the presence of angular momentum. Focusing on the application of holography to the quark–gluon plasma (of the various forms arising in the early Universe and in heavy-ion collisions), we find that these potential violations never actually occur. This suggests that the consistency condition is a “law of physics” expressing a particular aspect of holography.

  5. Electrokinetic desalination of sandstones for NaCl removal

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Christensen, Iben V.

    2012-01-01

    of reliable methods to remove the damaging salts in order to stop the decay. Electrokinetic desalination of fired clay bricks have previously shown efficient in laboratory scale and in the present work the method is tested for desalination of Cotta and Posta sandstones, which both have lower porosity than...... the bricks studied. The stones were contaminated with NaCl by submersion prior to the desalination experiments, where an electric DC field was applied to the stones from electrodes placed in clay poultice. Two poultice types were tested: calcareous clay used brick production and a mixture of kaolinite...... surface) applied. At the end of all desalination experiments the water content in the poultice at the cathode was higher than in the poultice at the anode, revealing electroosmotic water transport. The water profiles in the stones, however, did not indicate electoosmosis as they were quite uniform within...

  6. Diagenesis of Cambrian and lower Carboniferous sandstones, southwest Sinai, Egypt

    Energy Technology Data Exchange (ETDEWEB)

    Abdel-Wahab, A.A.; Salem, A.M.K. [Tanta Univ., Kafr El-Sheikh (Egypt); McBride, E.F. [Univ. of Texas, Austin, TX (United States)

    1996-12-31

    Quartzose and feldspathic Cambrian and Lower Carboniferous sandstones (fluvial > marine > eolian) deposited on the Arabian shield in southwestern Sinai were not buried more than 1 to 1.5 km until Late Cretaceous and younger time, when the deepest rocks reached 2.5 km. Porosity was reduced by compaction to about 26%. Grain rearrangement was the main mechanism of compaction; intergranular pressure solution and ductile grain deformation are insignificant. Cementation by iron oxide (5%), quartz (3%), calcite (2%), kaolinite (2%) and K-feldspar (< 1%) reduced porosity to 12-15% except in silcretes and some ferricretes, where porosity was reduced to non-reservoir quality. Cements have no selectivity for certain textures or stratigraphic positions.

  7. Diagenesis of Cambrian and lower Carboniferous sandstones, southwest Sinai, Egypt

    Energy Technology Data Exchange (ETDEWEB)

    Abdel-Wahab, A.A.; Salem, A.M.K. (Tanta Univ., Kafr El-Sheikh (Egypt)); McBride, E.F. (Univ. of Texas, Austin, TX (United States))

    1996-01-01

    Quartzose and feldspathic Cambrian and Lower Carboniferous sandstones (fluvial > marine > eolian) deposited on the Arabian shield in southwestern Sinai were not buried more than 1 to 1.5 km until Late Cretaceous and younger time, when the deepest rocks reached 2.5 km. Porosity was reduced by compaction to about 26%. Grain rearrangement was the main mechanism of compaction; intergranular pressure solution and ductile grain deformation are insignificant. Cementation by iron oxide (5%), quartz (3%), calcite (2%), kaolinite (2%) and K-feldspar (< 1%) reduced porosity to 12-15% except in silcretes and some ferricretes, where porosity was reduced to non-reservoir quality. Cements have no selectivity for certain textures or stratigraphic positions.

  8. Process-dependent residual trapping of CO2 in sandstone

    Science.gov (United States)

    Zuo, Lin; Benson, Sally M.

    2014-04-01

    This paper demonstrates that the nature and extent of residual CO2 trapping depend on the process by which the CO2 phase is introduced into the rock. We compare residual trapping of CO2 in Berea Sandstone by imbibing water into a core containing either exsolved CO2 or CO2 introduced by drainage. X-ray computed tomography measurements are used to map the spatial distribution of CO2 preimbibition and postimbibition. Unlike during drainage where the CO2 distribution is strongly influenced by the heterogeneity of the rock, the distribution of exsolved CO2 is comparatively uniform. Postimbibition, the CO2 distribution retained the essential features for both the exsolved and drainage cases, but twice as much residual trapping is observed for exsolved CO2 even with similar preimbibition gas saturations. Residually trapped exsolved gas also disproportionately reduced water relative permeability. Development of process-dependent parameterization will help better manage subsurface flow processes and unlock benefits from gas exsolution.

  9. Reservoir characterization of Pennsylvanian Sandstone Reservoirs. Annual report

    Energy Technology Data Exchange (ETDEWEB)

    Kelkar, M.

    1992-09-01

    This annual report describes the progress during the second year of a project on Reservoir Characterization of Pennsylvanian Sandstone Reservoirs. The report is divided into three sections: (i) reservoir description and scale-up procedures; (ii) outcrop investigation; (iii) in-fill drilling potential. The first section describes the methods by which a reservoir can be characterized, can be described in three dimensions, and can be scaled up with respect to its properties, appropriate for simulation purposes. The second section describes the progress on investigation of an outcrop. The outcrop is an analog of Bartlesville Sandstone. We have drilled ten wells behind the outcrop and collected extensive log and core data. The cores have been slabbed, photographed and the several plugs have been taken. In addition, minipermeameter is used to measure permeabilities on the core surface at six inch intervals. The plugs have been analyzed for the permeability and porosity values. The variations in property values will be tied to the geological descriptions as well as the subsurface data collected from the Glen Pool field. The third section discusses the application of geostatistical techniques to infer in-fill well locations. The geostatistical technique used is the simulated annealing technique because of its flexibility. One of the important reservoir data is the production data. Use of production data will allow us to define the reservoir continuities, which may in turn, determine the in-fill well locations. The proposed technique allows us to incorporate some of the production data as constraints in the reservoir descriptions. The technique has been validated by comparing the results with numerical simulations.

  10. Consistent quantum measurements

    Science.gov (United States)

    Griffiths, Robert B.

    2015-11-01

    In response to recent criticisms by Okon and Sudarsky, various aspects of the consistent histories (CH) resolution of the quantum measurement problem(s) are discussed using a simple Stern-Gerlach device, and compared with the alternative approaches to the measurement problem provided by spontaneous localization (GRW), Bohmian mechanics, many worlds, and standard (textbook) quantum mechanics. Among these CH is unique in solving the second measurement problem: inferring from the measurement outcome a property of the measured system at a time before the measurement took place, as is done routinely by experimental physicists. The main respect in which CH differs from other quantum interpretations is in allowing multiple stochastic descriptions of a given measurement situation, from which one (or more) can be selected on the basis of its utility. This requires abandoning a principle (termed unicity), central to classical physics, that at any instant of time there is only a single correct description of the world.

  11. Heterogeneity, permeability patterns, and permeability upscaling: Physical characterization of a block of Massillon sandstone exhibiting nested scales of heterogeneity

    Energy Technology Data Exchange (ETDEWEB)

    TIDWELL,VINCENT C.; WILSON,JOHN L.

    2000-04-20

    Over 75,000 permeability measurements were collected from a meter-scale block of Massillon sandstone, characterized by conspicuous cross bedding that forms two distinct nested-scales of heterogeneity. With the aid of a gas minipermeameter, spatially exhaustive fields of permeability data were acquired at each of five different sample supports (i.e. sample volumes) from each block face. These data provide a unique opportunity to physically investigate the relationship between the multi-scale cross-stratified attributes of the sandstone and the corresponding statistical characteristics of the permeability. These data also provide quantitative physical information concerning the permeability upscaling of a complex heterogeneous medium. Here, a portion of the data taken from a single block face cut normal to stratification is analyzed. Results indicate a strong relationship between the calculated summary statistics and the cross-stratified structural features visible evident in the sandstone sample. Specifically, the permeability fields and semivariograms are characterized by two nested scales of heterogeneity, including a large-scale structure defined by the cross-stratified sets (delineated by distinct bounding surfaces) and a small-scale structure defined by the low-angle cross-stratification within each set. The permeability data also provide clear evidence of upscaling. That is, each calculated summary statistic exhibits distinct and consistent trends with increasing sample support. Among these trends are an increasing mean, decreasing variance, and an increasing semivariogram range. Results also clearly indicate that the different scales of heterogeneity upscale differently, with the small-scale structure being preferentially filtered from the data while the large-scale structure is preserved. Finally, the statistical and upscaling characteristics of individual cross-stratified sets were found to be very similar owing to their shared depositional environment

  12. The Petrology and Diagenetic History of the Phacoides Sandstone, Temblor Formation at the McKittrick Oil Field, California

    Science.gov (United States)

    Kaess, A. B.; Horton, R. A.

    2015-12-01

    The McKittrick oil field is located near the western edge of the San Joaquin Basin, California. The oil field is currently in production with 480 wells producing from the Tulare, San Joaquin, Reef Ridge, Monterey, Temblor, Tumey, and Kreyenhagen formations. Within the Temblor Formation production is mainly from the Miocene Carneros and the Phacoides sandstones. Eighty-two samples from the Phacoides sandstone (2403 - 3045 m below surface) were obtained from the California Well Sample Repository to characterize and understand the diagenetic history and its influence on its reservoir properties. Petrographic thin sections were analyzed by quantitative optical petrography, energy dispersive X-ray spectrometry, and imaging with back-scatter electron and cathodoluminescence. The Phacoides sandstone consists of fine to very coarse, poorly to well-sorted, arkosic arenites, and wackes with detrital framework grains including sub-angular quartz, K-feldspar (microcline and orthoclase), plagioclase, and lithic fragments. Ba-free, Ba-rich, and perthitic K-feldspars are present. Accessory minerals include glauconite, biotite, muscovite, magnetite, titanomagnetite, sphene, zircon, apatite, corundum, and rutile. Diagenetic alteration includes: (1) compaction, (2) mineral dissolution, (3) albitization of feldspars, alteration of biotite to pyrite and chlorite, replacement of framework grains by calcite, (4) alteration of volcanic rock fragments, (5) cementation by kaolinite, calcite and dolomite, and (6) precipitation of K-feldspar and quartz overgrowths. Early-formed fractures were healed by authigenic quartz, albite, and K-feldspars. Precipitation of carbonates and clays, rearranging of broken grains, and formation of pseudomatrix reduced primary porosity. Secondary porosity is common and formed initially by the dissolution of plagioclase (excluding albite) and volcanic fragments, and later by dissolution of calcite, dolomite, and detrital K-feldspars. Hydrocarbon emplacement was

  13. When Is Holography Consistent?

    CERN Document Server

    McInnes, Brett

    2015-01-01

    Holographic duality relates two radically different kinds of theory: one with gravity, one without. The very existence of such an equivalence imposes strong consistency conditions which are, in the nature of the case, hard to satisfy. Recently a particularly deep condition of this kind, relating the minimum of a probe brane action to a gravitational bulk action (in a Euclidean formulation), has been recognised; and the question arises as to the circumstances under which it, and its Lorentzian counterpart, are satisfied. We discuss the fact that there are physically interesting situations in which one or both versions might, in principle, \\emph{not} be satisfied. These arise in two distinct circumstances: first, when the bulk is not an Einstein manifold, and, second, in the presence of angular momentum. Focusing on the application of holography to the quark-gluon plasma (of the various forms arising in the early Universe and in heavy-ion collisions), we find that these potential violations never actually occur...

  14. Quantitative studies of hydrocarbon loss of the Silurian bitumen sandstone in the Tarim Basin

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The evolution of Tarim Basin experienced several tectonic movements,of which Caledonian movement caused a serious damage to reservoirs of Silurian. The earlier reservoirs size and the later hydrocarbon loss are two key factors to exploration prospect of Silurian. On the basis of net thickness of bituminous sandstone and recovery coefficient of crude oil converting to bitumen,the scale of the hydrocarbon loss of palaeo-accumulation in bitumen sandstone of Silurian was calculated (86.30×108t). The deter-mination of net thickness of bitumen sandstone was completed mainly by several methods,such as physical property demarcation,observing lithology,grains with oil inclusion (GOI) technology,and quantitative grains fluorescence (QGF) technology. The samples of black sandstone and white sand-stone were collected and compared by means of the methods mentioned above. The results showed that there was little hydrocarbon,or none,in the white sandstone. The recovery coefficient was ob-tained by the analyses of plentiful physical parameters of crude oil and bitumen sandstone,based on the hypothesis that nonhydrocarbon compounds and bitumen were invariable in the process of bitu-men forming. The calculated result,which is more scientific and actual,indicates the exploration pros-pect is more promising in Silurian of the Tarim Basin.

  15. Origin and implications of fluid inclusions from filled fractures, Oriskany Sandstone, Allegheny Plateau, Pennsylvania

    Energy Technology Data Exchange (ETDEWEB)

    Basilone, T.; Anderson, T.; Burruss, R.C.

    1984-12-01

    Two cores from the Lower Devonian Oriskany Sandstone underlying the Allegheny Plateau in south-central Somerset County, Pennsylvania, contain fractures that may either be filled with epigenetic minerals or unfilled. The 1 Sipe core, taken from an unproductive well drilled on the crest of an anticlinal structure, is characterized by numerous discontinuous vertical fractures. The 1 Romesburg core, taken from a productive well drilled on the flank of an anticlinal structure, contains numerous fractures that lie parallel with bedding planes. The walls of these fractures consist of smooth slickensided surfaces. Quartz and ferroan-calcite crystals filling fractures contain numerous hydrocarbon-bearing fluid inclusions. The distribution of these fluid inclusions within most minerals allowed a determination to be made regarding the relative times of migration of fluid hydrocarbon phases in the subsurface with respect to the paragenetic sequence of mineralization events. Analysis of fluid inclusions indicates that fractures were opened at 22,000 ft (6700 m) and remained open throughout an extended period of uplift. Furthermore, inclusions contain hydrocarbon-rich fluids that are comparable to reservoir hydrocarbons in the nearby Shamrock field. This relationship implies that hydrocarbons that currently exist in reservoirs were conducted along fractures that were once open. Fractures crosscut diagenetic features, indicating that diagenesis, for the most part, preceded fracture events. Although they differ in origin and orientation, fractures characterizing Oriskany strata were healed by a consistent sequence of epigenetic minerals.

  16. Acoustic emission signals frequency-amplitude characteristics of sandstone after thermal treated under uniaxial compression

    Science.gov (United States)

    Kong, Biao; Wang, Enyuan; Li, Zenghua; Wang, Xiaoran; Niu, Yue; Kong, Xiangguo

    2017-01-01

    Thermally treated sandstone deformation and fracture produced abundant acoustic emission (AE) signals. The AE signals waveform contained plentiful precursor information of sandstone deformation and fracture behavior. In this paper, uniaxial compression tests of sandstone after different temperature treatments were conducted, the frequency-amplitude characteristics of AE signals were studied, and the main frequency distribution at different stress level was analyzed. The AE signals frequency-amplitude characteristics had great difference after different high temperature treatment. Significant differences existed of the main frequency distribution of AE signals during thermal treated sandstone deformation and fracture. The main frequency band of the largest waveforms proportion was not unchanged after different high temperature treatments. High temperature caused thermal damage to the sandstone, and sandstone deformation and fracture was obvious than the room temperature. The number of AE signals was larger than the room temperature during the initial loading stage. The low frequency AE signals had bigger proportion when the stress was 0.1, and the maximum value of the low frequency amplitude was larger than high frequency signals. With the increase of stress, the low and high frequency AE signals were gradually increase, which indicated that different scales ruptures were broken in sandstone. After high temperature treatment, the number of high frequency AE signals was significantly bigger than the low frequency AE signals during the latter loading stage, this indicates that the small scale rupture rate of recurrence and frequency were more than large scale rupture. The AE ratio reached the maximum during the sandstone instability failure period, and large scale rupture was dominated in the failure process. AE amplitude increase as the loading increases, the deformation and fracture of sandstone was increased gradually. By comparison, the value of the low frequency

  17. Fracturing and Damage to Sandstone Under Coupling Effects of Chemical Corrosion and Freeze-Thaw Cycles

    Science.gov (United States)

    Han, Tielin; Shi, Junping; Cao, Xiaoshan

    2016-11-01

    Rapid freeze-thaw (FT) cycles were adopted to explore the damage deterioration mechanism and mechanical properties of sandstone specimens under the coupling effects of different chemical solutions and FT cycles. The variation regularities of the FT cycles and physical and mechanical properties of sandstone specimens immersed in different chemical solutions were analyzed by using sandstone sampled from a Chinese riverbank slope. The damage variable based on porosity variation was used in the quantitative analysis of the damage to the sandstone under the coupling effects of chemical corrosion and FT cycles. Experimental results showed that the sandstone specimens weakened substantially under those effects. Their fracture toughness K IC, splitting tensile strength, and compressive strength showed a similar deteriorating trend with various numbers of FT cycles. However, a difference exists in the deterioration degree of their mechanical parameters, i.e., the deterioration degree of their fracture toughness K IC is the greatest followed by that of splitting tensile strength, and that of compressive strength is relatively small. Strong acid solutions may aggravate the deterioration of FT damage in sandstones, but at the early stage of the experiment, strong alkaline solutions inhibited sandstone damage deterioration. However, the inhibiting effect disappeared when the number of FT cycles exceeded 25. The different chemical solutions had a different effect on the FT damage degree of the sandstone specimens; for example, SO4 2- ions had a greater effect on FT damage than did HCO3 - ions. Water-chemical solutions and FT cycles promote each other in deteriorating rocks and simultaneously affect the damage deterioration degree of sandstones.

  18. Investigation on porosity and permeability change of Mount Simon sandstone (Knox County, IN, USA) under geological CO2 sequestration conditions: a numerical simulation approach

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Liwei [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Soong, Yee [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Dilmore, Robert M. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States)

    2016-01-14

    In this paper, a numerical model was developed to simulate reactive transport with porosity and permeability change of Mount Simon sandstone (samples from Knox County, IN) after 180 days of exposure to CO2-saturated brine under CO2 sequestration conditions. The model predicted formation of a high-porosity zone adjacent to the surface of the sample in contact with bulk brine, and a lower porosity zone just beyond that high-porosity zone along the path from sample/bulk brine interface to sample core. The formation of the high porosity zone was attributed to dissolution of quartz and muscovite/illite, while the formation of the lower porosity zone adjacent to the aforementioned high porosity zone was attributed to precipitation of kaolinite and feldspar. The model predicted a 40% permeability increase for the Knox sandstone sample after 180 days of exposure to CO2-saturated brine, which was consistent with laboratory-measured permeability results. Model-predicted solution chemistry results were also found to be consistent with laboratory-measured solution chemistry data. Finally, initial porosity, initial feldspar content and the exponent n value (determined by pore structure and tortuosity) used in permeability calculations were three important factors affecting permeability evolution of sandstone samples under CO2 sequestration conditions.

  19. Investigation on porosity and permeability change of Mount Simon sandstone (Knox County, IN, USA) under geological CO 2 sequestration conditions: a numerical simulation approach

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Liwei [US Department of Energy, National Energy Technology Laboratory, Pittsburgh PA USA; Soong, Yee [US Department of Energy, National Energy Technology Laboratory, Pittsburgh PA USA; Dilmore, Robert M. [US Department of Energy, National Energy Technology Laboratory, Pittsburgh PA USA

    2016-01-14

    A numerical model was developed to simulate reactive transport with porosity and permeability change of Mount Simon sandstone (samples from Knox County, IN) after 180 days of exposure to CO2-saturated brine under CO2 sequestration conditions. The model predicted formation of a high-porosity zone adjacent to the surface of the sample in contact with bulk brine, and a lower porosity zone just beyond that high-porosity zone along the path from sample/bulk brine interface to sample core. The formation of the high porosity zone was attributed to dissolution of quartz and muscovite/illite, while the formation of the lower porosity zone adjacent to the aforementioned high porosity zone was attributed to precipitation of kaolinite and feldspar. The model predicted a 40% permeability increase for the Knox sandstone sample after 180 days of exposure to CO2-saturated brine, which was consistent with laboratory-measured permeability results. Model-predicted solution chemistry results were also found to be consistent with laboratory-measured solution chemistry data. Initial porosity, initial feldspar content and the exponent n value (determined by pore structure and tortuosity) used in permeability calculations were three important factors affecting permeability evolution of sandstone samples under CO2 sequestration conditions. 1

  20. Investigation on porosity and permeability change of Mount Simon sandstone (Knox County, IN, USA) under geological CO 2 sequestration conditions: a numerical simulation approach

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Liwei [National Energy Technology Lab. (NETL), Pittsburgh, OR (United States); Soong, Yee [National Energy Technology Lab. (NETL), Pittsburgh, OR (United States); Dilmore, Robert M. [National Energy Technology Lab. (NETL), Pittsburgh, OR (United States)

    2016-01-14

    A numerical model was developed to simulate reactive transport with porosity and permeability change of Mount Simon sandstone (samples from Knox County, IN) after 180 days of exposure to CO2-saturated brine under CO2 sequestration conditions. The model predicted formation of a high-porosity zone adjacent to the surface of the sample in contact with bulk brine, and a lower porosity zone just beyond that high-porosity zone along the path from sample/bulk brine interface to sample core. The formation of the high porosity zone was attributed to dissolution of quartz and muscovite/illite, while the formation of the lower porosity zone adjacent to the aforementioned high porosity zone was attributed to precipitation of kaolinite and feldspar. The model predicted a 40% permeability increase for the Knox sandstone sample after 180 days of exposure to CO2-saturated brine, which was consistent with laboratory-measured permeability results. Model-predicted solution chemistry results were also found to be consistent with laboratory-measured solution chemistry data. Initial porosity, initial feldspar content and the exponent n value (determined by pore structure and tortuosity) used in permeability calculations were three important factors affecting permeability evolution of sandstone samples under CO2 sequestration conditions. 1

  1. Investigation on porosity and permeability change of Mount Simon sandstone (Knox County, IN, USA) under geological CO 2 sequestration conditions: a numerical simulation approach

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Liwei [US Department of Energy, National Energy Technology Laboratory, Pittsburgh PA USA; Soong, Yee [US Department of Energy, National Energy Technology Laboratory, Pittsburgh PA USA; Dilmore, Robert M. [US Department of Energy, National Energy Technology Laboratory, Pittsburgh PA USA

    2016-01-14

    In this paper, a numerical model was developed to simulate reactive transport with porosity and permeability change of Mount Simon sandstone (samples from Knox County, IN) after 180 days of exposure to CO2-saturated brine under CO2 sequestration conditions. The model predicted formation of a high-porosity zone adjacent to the surface of the sample in contact with bulk brine, and a lower porosity zone just beyond that high-porosity zone along the path from sample/bulk brine interface to sample core. The formation of the high porosity zone was attributed to dissolution of quartz and muscovite/illite, while the formation of the lower porosity zone adjacent to the aforementioned high porosity zone was attributed to precipitation of kaolinite and feldspar. The model predicted a 40% permeability increase for the Knox sandstone sample after 180 days of exposure to CO2-saturated brine, which was consistent with laboratory-measured permeability results. Model-predicted solution chemistry results were also found to be consistent with laboratory-measured solution chemistry data. Finally, initial porosity, initial feldspar content and the exponent n value (determined by pore structure and tortuosity) used in permeability calculations were three important factors affecting permeability evolution of sandstone samples under CO2 sequestration conditions.

  2. Provenance and weathering depth of carbonaceous gotland sandstone by use of carbon and oxygen isotopes

    Science.gov (United States)

    Åberg, G.; Löfvendahl, R.; Stijfhoorn, D.; Råheim, A.

    Carbon and oxygen isotope ratios of carbonates (calcite) from different sites and stratigraphic levels of the Gotland sandstone show that it might be possible to fingerprint the different quarries. Preliminary tests of nine samples of Gotland sandstone from different buildings show that the laser microprobe is an excellent tool for estimating depth of weathering on this carbonaceous sandstone. Analyses perpendicular to the stone surface gave a similar trend for the carbon and oxygen isotope ratios, although changes go deeper with δ13C than δ18O. Depth of weathering is controlled by exposure, location, biologic overgrowth and salt efflorescence. The effect of earlier conservation treatment with linseed oil can also be traced.

  3. Experimental determination of noble gas, SF6 and CO2 flow profiles through a porous sandstone

    Science.gov (United States)

    Kilgallon, Rachel; Gilfillan, Stuart; Edlmann, Katriona; McDermott, Chris

    2016-04-01

    The noble gases (He, Ne, Ar, Kr and Xe) and SF6 have recently been used as artificial and inherent tracers of CO2 flow and migration from within[1,2] and from geological reservoirs[3]. However, outstanding questions remain, particularly regarding the flow behaviour of the noble gases compared to CO2. Here we present results from specially constructed experimental equipment, which has been used to determine the factors affecting transport of noble gases relative to CO2 in a porous sandstone. The experimental setup consists of a sample loop that can be loaded with a desired gas mixture. This sample can be released as a pulse into a feeder gas stream through a flow cell. The flow cell consists of a 3.6 cm diameter core, which can be of any length. The sample is surrounded by aluminium foil and treated with epoxy resin inside stainless steel tubing. The flow cell is encased by two purpose designed dispersion end plates. Real-time analysis of the arrival peaks of the gases downstream is recorded using a Quadrupole Mass Spectrometer (QMS). For the experiments, a 0.96 m core of Fell Sandstone was selected to represent a porous media. Noble gases and SF6 pulses were flowed through a CO2 carrier gas at five different pressure gradients (10 - 50 kPa) with arrival profiles measured using the QMS. Surprisingly, peak arrival times of He were slower than the other noble gases at each pressure gradient. The differences in peak arrival times between He and other noble gases increased as pressure decreased and the curve profiles for each noble gas differ significantly. The heavier noble gases (Kr and Xe) along with SF6 show a steeper peak rise at initial appearance, but have a longer duration profile than the He curves. Interestingly, the breakthrough curve profiles for both Kr and Xe were similar to SF6 indicating that Kr and Xe could be substituted for SF6, which is a potent greenhouse gas, in tracing applications. In addition, CO2 pulses were passed through a N2 carrier gas. The

  4. Fluid migration through sandstone fractures in Gale Crater, Mars

    Science.gov (United States)

    Yen, Albert; Blake, David; Bristow, Thomas; Chipera, Steve; Downs, Robert; Gellert, Ralf; Grotzinger, John P.; Ming, Doug; Morris, Richard; Morrison, Shaunna; Rampe, Liz; Thompson, Lucy; Treiman, Allan; Vaniman, David; MSL Science Team

    2016-10-01

    The Curiosity Mars rover encountered numerous occurrences of light-toned fractures in lithified sediments along its traverse in Gale Crater. These alteration zones can be traced for tens of meters across the landscape and are generally less than a meter in width. Two of these features were investigated in detail by the rover instruments, including drilling to acquire samples both within and immediately outside the lighter-toned areas.The chemical composition established by the Alpha Particle X-ray Spectrometer (APXS) on the arm of the rover shows that the alteration zones are significantly enhanced in silica (40% increase) and sulfur (factor of ~5) relative to the surrounding rocks. Concentrations of Fe, Mg, Al, Mn, Ni and Zn are reduced by a factor of two or more. The correlation between Ca and SO3 indicates the presence of Ca-sulfates, but with up to 15% SO3 (and only 6% to 9% CaO) in the APXS data, the presence of Mg and Fe sulfates in the altered fractures is likely.The Chemistry and Mineralogy (CheMin) X-ray diffraction instrument analyzed the drill fines and found mostly plagioclase feldspar, pyroxenes and magnetite in the unaltered sandstones. X-ray amorphous material and minor hematite and Ca-sulfates are also present. Samples from the alteration zones, however, show a factor of two decrease in the pyroxene to feldspar ratio, abundant Ca-sulfates in various hydration states, and a majority fraction of amorphous material rich in silica and mixed-cation sulfates.The direct comparison of samples within and adjacent to the light toned fractures indicates an alteration process involving the dissolution of pyroxenes and removal of metal cations. The mobility of Al and the likely presence of Fe-sulfates suggest alteration in an acidic environment, but additional moderate pH episodes cannot be ruled out. These features post-date the sandstone lithification and are among the youngest fluid events studied thus far in Gale Crater.

  5. Temperature dependent elasticity and damping in dehydrated sandstone

    Science.gov (United States)

    Darling, T. W.; Struble, W.

    2013-12-01

    Work reported previously at this conference, outlining our observation of anomalously large elastic softening and damping in dehydrated Berea sandstone at elevated temperatures, has been analysed to study shear and compressional effects separately. Modeling of the sample using COMSOL software was necessary to identify modes, as the vibration spectrum of the sample is poorly approximated by a uniform isotropic solid. The first torsional mode of our evacuated, dry, core softens at nearly twice the rate of Young's modulus modes (bending and compressional) and is also damped nearly twice as strongly as temperature increases. We consider two possible models for explaining this behavior, based on the assumption that the mechanical properties of the sandstone are dominated by the framework of quartz grains and polycrystalline cementation, neglecting initially the effects of clay and feldspar inclusions. The 20cm x 2.54cm diameter core is dry such that the pressure of water vapor in the experiment chamber is below 1e-6 Torr at 70C, suggesting that surface water beyond a small number of monolayers is negligible. Our models consider (1) enhanced sliding of grain boundaries in the cementation at elevated temperature and reduced internal water content, and (2) strain microcracking of the cementatioin at low water content due to anisotropic expansion in the quartz grains. In model (1) interfaces parallel to polyhedral grain surfaces were placed in the cement bonds and assigned frictional properties. Model (2) has not yet been implemented. The overall elasticity of a 3-D several-grain model network was determined by modeling quasistatic loading and measuring displacements. Initial results with a small number of grains/bonds suggests that only the first model provides softening and damping for all the modes, however the details of the effects of defect motioin at individual interfaces as the source for the frictional properties is still being evaluated. Nonlinear effects are

  6. Evidence of multi-stage faulting by clay mineral analysis: Example in a normal fault zone affecting arkosic sandstones (Annot sandstones)

    Science.gov (United States)

    Buatier, Martine D.; Cavailhes, Thibault; Charpentier, Delphine; Lerat, Jérémy; Sizun, Jean Pierre; Labaume, Pierre; Gout, Claude

    2015-06-01

    Fault affecting silicoclastic sediments are commonly enriched in clay minerals. Clays are sensitive to fluid-rock interactions and deformation mechanisms; in this paper, they are used as proxy for fault activity and behavior. The present study focuses on clay mineral assemblages from the Point Vert normal fault zone located in the Annot sandstones, a Priabonian-Rupelian turbidite succession of the Alpine foredeep in SE France. In this area, the Annot sandstones were buried around 6-8 km below the front of Alpine nappes soon after their deposition and exhumed during the middle-late Miocene. The fault affects arkosic sandstone beds alternating with pelitic layers, and displays throw of about thirty meters. The fault core zone comprises intensely foliated sandstones bounding a corridor of gouge about 20 cm thick. The foliated sandstones display clay concentration along S-C structures characterized by dissolution of K-feldspar and their replacement by mica, associated with quartz pressure solution, intense microfracturation and quartz vein precipitation. The gouge is formed by a clayey matrix containing fragments of foliated sandstones and pelites. However, a detailed petrographical investigation suggests complex polyphase deformation processes. Optical and SEM observations show that the clay minerals fraction of all studied rocks (pelites and sandstones from the damage and core zones of the fault) is dominated by white micas and chlorite. These minerals have two different origins: detrital and newly-formed. Detrital micas are identified by their larger shape and their chemical composition with a lower Fe-Mg content than the newly-formed white micas. In the foliated sandstones, newly-formed white micas are concentrated along S-C structures or replace K-feldspar. Both types of newly formed micas display the same chemical composition confirmed microstructural observations suggesting that they formed in the same conditions. They have the following structural formulas: Na0

  7. Reservoir zonation based on statistical analyses: A case study of the Nubian sandstone, Gulf of Suez, Egypt

    Science.gov (United States)

    El Sharawy, Mohamed S.; Gaafar, Gamal R.

    2016-12-01

    Both reservoir engineers and petrophysicists have been concerned about dividing a reservoir into zones for engineering and petrophysics purposes. Through decades, several techniques and approaches were introduced. Out of them, statistical reservoir zonation, stratigraphic modified Lorenz (SML) plot and the principal component and clustering analyses techniques were chosen to apply on the Nubian sandstone reservoir of Palaeozoic - Lower Cretaceous age, Gulf of Suez, Egypt, by using five adjacent wells. The studied reservoir consists mainly of sandstone with some intercalation of shale layers with varying thickness from one well to another. The permeability ranged from less than 1 md to more than 1000 md. The statistical reservoir zonation technique, depending on core permeability, indicated that the cored interval of the studied reservoir can be divided into two zones. Using reservoir properties such as porosity, bulk density, acoustic impedance and interval transit time indicated also two zones with an obvious variation in separation depth and zones continuity. The stratigraphic modified Lorenz (SML) plot indicated the presence of more than 9 flow units in the cored interval as well as a high degree of microscopic heterogeneity. On the other hand, principal component and cluster analyses, depending on well logging data (gamma ray, sonic, density and neutron), indicated that the whole reservoir can be divided at least into four electrofacies having a noticeable variation in reservoir quality, as correlated with the measured permeability. Furthermore, continuity or discontinuity of the reservoir zones can be determined using this analysis.

  8. Cathodoluminescence investigations on quartz cement in the sandstones of Khabour Formation from Iraqi Kurdistan Region, Northern Iraq

    Science.gov (United States)

    Omer, Muhamed F.; Friis, Henrik

    2014-03-01

    The Ordovician deltaic to shallow marine Khabour Formation in Northern Iraq consists mainly of sandstone with minor siltstone and interbedded shale. The sandstones are pervasively cemented by quartz that resulted in very little preserved primary porosity. Cathodoluminescence and petrographic studies showed that the silica cementation occurred in five successive phases which can be distinguished by their luminescence pattern. The precipitations of two phases have predated the major compaction process while the other phases are younger. The successive phases represent a sequence of changes in silica supply which were classified as very early and early, derived from dissolved biogenic silica that precipitated as opal/microquartz, possibly pre-compactional and of non-luminescent quartz overgrowth type. This was followed by phases whose silica supply derived from pressure solution of quartz, dissolution of feldspar, and hydrothermal fluids related to major thrust fault event. These successive quartz cement phases showed an increase in luminescence and the development of complicated zonation pattern in late-stage quartz cementation.

  9. Anatomy of biologically mediated opal speleothems in the World's largest sandstone cave: Cueva Charles Brewer, Chimantá Plateau, Venezuela

    Science.gov (United States)

    Aubrecht, R.; Brewer-Carías, Ch.; Šmída, B.; Audy, M.; Kováčik, Ľ.

    2008-01-01

    Siliceous speleothems can be formed in sandstone caves. Recently, opal "biospeleothems" have been found in the World's largest cave in Precambrian sandstones on the Chimantá Tepui in Venezuela. The speleothems, although reminiscent of normal stalactites and stalagmites from limestone caves, are in fact large microbialites. More than a dozen forms were distinguished, but they share a common structure and origin. They consist of two main types: 1. fine-laminated columnar stromatolite formed by silicified filamentous microbes (either heterotrophic filamentous bacteria or cyanobacteria) and 2. a porous peloidal stromatolite formed by Nostoc-type cyanobacteria. The first type usually forms the central part and the second type, the outer part, of speleothems. Fungal hyphae, metazoan and plant remains also subordinately contribute to speleothem construction. The speleothems occur out of the reach of flowing water; the main source of silica is the condensed cave moisture which is the main dissolution-reprecipitation agent. Speleothems which originated by encrustation of spider threads are unique.

  10. Uranium-Series Disequilibria in the Groundwater of the Shihongtan Sandstone-Hosted Uranium Deposit, NW China

    Directory of Open Access Journals (Sweden)

    Xinjian Peng

    2015-12-01

    Full Text Available Uranium (U concentration and the activities of 238U, 234U, and 230Th were determined for groundwaters, spring waters, and lake water collected from the Shihongtan sandstone-hosted U ore district and in the surrounding area, NW China. The results show that the groundwaters from the oxidizing aquifer with high dissolved oxygen concentration (O2 and oxidation-reduction potential (Eh are enriched in U. The high U concentration of groundwaters may be due to the interaction between these oxidizing groundwaters and U ore bodies, which would result in U that is not in secular equilibrium. Uranium is re-precipitated as uraninite on weathered surfaces and organic material, forming localized ore bodies in the sandstone-hosted aquifer. The 234U/238U, 230Th/234U, and 230Th/238U activity ratios (ARs for most water samples show obvious deviations from secular equilibrium (0.27–2.86, indicating the presence of water-rock/ore interactions during the last 1.7 Ma and probably longer. The 234U/238U AR generally increases with decreasing U concentrations in the groundwaters, suggesting that mixing of two water sources may occur in the aquifer. This is consistent with the fact that most of the U ore bodies in the deposit have a tabular shape originati from mixing between a relatively saline fluid and a more rapidly flowing U-bearing meteoric water.

  11. Rice Lake National Wildlife Refuge : Sandstone Unit : Mille Lacs National Wildlife Refuge : Fiscal year 2002

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This annual narrative report for Rice Lake (including the Sandstone Unit) and Mille Lacs National Wildlife Refuges outlines Refuge accomplishments during the 2002...

  12. Investigating the effect of unloading on artificial sandstone behaviour using the Discrete Element Method

    Science.gov (United States)

    Huang, Yueqin; Cheng, Yi Pik; Coop, Matthew

    2017-06-01

    The Discrete Element Method (DEM) was used to simulate the mechanical behaviour of a reservoir sandstone. Triaxial tests were carried out using 3D-DEM to simulate the stress-strain behaviour of a sandstone with comparisons made between the numerical tests and the laboratory tests. The influence of isotropic unloading was investigated, which was found to have impacts on bond breakages and was successfully captured in the 3D shearing processes. It was found that bond breakages correlated strongly with the stress-strain behaviour of the sandstone affecting the peak strength. It was also found that unloading affected the bond breakages, which then changed the mechanical behaviour of sandstone. The tangent stiffnesses of simulated virgin and cored samples under different confining stresses were compared. From the tangent stiffnesses, gross yield envelopes and the yielding surfaces for unloaded samples and virgin samples were plotted and analysed in detail.

  13. Rice Lake National Wildlife Refuge : Mille Lacs National Wildlife Refuge : Sandstone Unit : Fiscal year 2003

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This annual narrative report for Rice Lake (including the Sandstone Unit) and Mille Lacs National Wildlife Refuges outlines Refuge accomplishments during the 2003...

  14. Compactional deformation bands in Wingate Sandstone; additional evidence of an impact origin for Upheaval Dome, Utah

    Science.gov (United States)

    Okubo, Chris H.; Schultz, Richard A.

    2007-04-01

    Field and microstructural observations from Upheaval Dome, in Canyonlands National Park, Utah, show that inelastic strain of the Wingate Sandstone is localized along compactional deformation bands. These bands are tabular discontinuities (Jurassic) age for this impact.

  15. Rice Lake National Wildlife Refuge : Mille Lacs National Wildlife Refuge : Sandstone Unit : Fiscal year 2004

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This annual narrative report for Rice Lake (including the Sandstone Unit) and Mille Lacs National Wildlife Refuges outlines Refuge accomplishments during the 2004...

  16. NUMERICAL MODELLING OF PROGRESSIVE FAILURE IN PARTICULATE COMPOSITES LIKE SANDSTONE

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    The beam-particle model is presented for analyzing the progressive failure of particulate composites such as sandstone and concrete. In the model, the medium is schematized as an assembly of particles which are linked through a network of brittle-breaking beam elements. The mechanical behaviour of particle elements is governed by the distinct element method and finite element method. The propagation of the cracking process in particulate composites is mimicked by removing the beam element from the mesh as soon as the stress in the beam exceeds the strength assigned to that particular beam. The new model can be utilized at a meso-scale and in different loading conditions. Two physical experiments are performed to verify the numerical results. The crack patterns and load-displacement response obtained with the proposed numerical model are in good agreement with the experimental results. Moreover, the influence of heterogeneity on crack patterns is also discussed and the correlation existing between the fracture evolution and the loads imposed on the specimen is characterized by fractal dimensions.

  17. Mineral changes in cement-sandstone matrices induced by biocementation

    Energy Technology Data Exchange (ETDEWEB)

    Verba, C. [National Energy Technology Lab. (NETL), Albany, OR (United States); Thurber, A. R. [Oregon State Univ., Corvallis, OR (United States). College of Earth, Ocean, and Atmospheric Sciences; Alleau, Y. [Oregon State Univ., Corvallis, OR (United States). College of Earth, Ocean, and Atmospheric Sciences; Koley, D. [Oregon State Univ., Corvallis, OR (United States). College of Science; Colwell, F. [Oregon State Univ., Corvallis, OR (United States). College of Earth, Ocean, and Atmospheric Sciences; Torres, M. E. [Oregon State Univ., Corvallis, OR (United States). College of Earth, Ocean, and Atmospheric Sciences

    2016-04-01

    Prevention of wellbore CO2 leakage is a critical component of any successful carbon capture, utilization, and storage program. Sporosarcina pasteurii is a bacterium that has demonstrated the potential ability to seal a compromised wellbore through the enzymatic precipitation of CaCO3. In this paper, we investigate the growth of S. pasteurii in a synthetic brine that mimics the Illinois Basin and on Mt. Simon sandstone encased in Class H Portland cement under high pressure and supercritical CO2 (PCO2) conditions. The bacterium grew optimum at 30 °C compared to 40 °C under ambient and high pressure (10 MPa) conditions; and growth was comparable in experiments at high PCO2. Sporosarcina pasteurii actively induced the biomineralization of CaCO3 polymorphs and MgCa(CO3)2 in both ambient and high pressure conditions as observed in electron microscopy. In contrast, abiotic (non-biological) samples exposed to CO2 resulted in the formation of surficial vaterite and calcite. Finally, the ability of S. pasteurii to grow under subsurface conditions may be a promising mechanism to enhance wellbore integrity.

  18. Experimental study on interaction between simulated sandstone and acidic fluid

    Institute of Scientific and Technical Information of China (English)

    Zhang Yongwang; Zeng Jianhu; Yu Bingsong

    2009-01-01

    In order to investigate the controlling mechanism of temperature, fluid and other factors on water-rock interaction in the diagenetic process, we performed a series of simulated experiments on the interaction between two kinds of fluids with different salinity and a composite mineral system (simulated sandstone), which contains albite, K-feldspar and other minerals. The experimental results showed that acidity was the most important factor that affected the dissolution of minerals in the composite mineral system. The lower the pH value, the more easily the minerals dissolved. At the same pH value, the dissolution abilities of different acids for various mineral components were also different. Compared to hydrochloric acid (inorganic acid), oxalic acid (organic acid) was more able to dissolve aluminosilicate minerals. However, the dissolution ability of oxalic acid for carbonate minerals was lower than that of hydrochloric acid. In the process of fluid-rock interaction,dissolution of feldspar was relatively complicated. Increase of temperature would accelerate the dissolution of feldspar. Under acidic conditions, albite had a higher dissolution rate than K-feldspar. K-feldspar could dissolve and convert into montmorillonite and kaolinite, while albite could dissolve and convert into kaolinite both at 40℃ and 80℃. Presence of organic acid, and decrease of pH value and water salinity were all favorable for the dissolution of feldspar, but weakened the ability to form clay minerals.

  19. Geometry of calcite cemented zones in shallow marine sandstones

    Energy Technology Data Exchange (ETDEWEB)

    Walderhaug, O.; Prestholm, E.; Oexnevad, I.E.I.

    1995-12-31

    In offshore oil production, tightly cemented calcite zones often form impermeable barriers to fluid flow an so adversely affect reservoir performance. Based on recent breakthroughs in the theory of the formation of calcite cemented zones, the project discussed in this paper was concerned with (1) Performing outcrop studies in order to increase the existing database on the geometry of calcite cemented zones, (2) Extending and refining methods of predicting the geometry of cored calcite cemented zones, and (3) Applying and illustrating the use of these methods by studying calcite cementation in shallow marine reservoir sandstones on the Norwegian shelf. The paper presents results from field work and applies these results and the criteria for recognizing geometrical forms of calcite cementation in cores to the Ula Formation of the Ula Field and the Rannoch Formation of the Gullfax Field. The results from the core and outcrop studies are integrated in a tentative identification key for cored calcite cemented zones. The work is part of PROFIT (Program for Research On Field oriented Improved recovery Technology), a research project conducted by RF - Rogaland Research in 1991-1994. 32 refs., 10 figs., 2 tabs.

  20. Mineralogical controls on NMR rock surface relaxivity: A case study of the Fontainebleau Sandstone

    Science.gov (United States)

    Livo, Kurt

    Pore size distribution is derived from nuclear magnetic resonance, but is scaled by surface relaxivity. While nuclear magnetic resonance studies generally focus on the difficulty of determining pore size distribution in unconventional shale reservoirs, there is a lack of discussion concerning pure quartz sandstones. Long surface relaxivity causes complications analyzing nuclear magnetic resonance data for pore size distribution determination. Currently, I am unaware of research that addresses the complicated pore size distribution determination in long relaxing, pure sandstone formations, which is essential to accurate downhole petrophysical modeling. The Fontainebleau sandstone is well known for its homogenous mineralogical makeup and wide range of porosity and permeability. The Hibernia sandstone exhibits a similar mineralogy and is characterized by a similar and porosity-permeability range to the Fontainebleau sandstones, but with a significantly higher portion of clay minerals (1-6%). I present systematic petrophysical properties such as porosity, pore size distribution from nuclear magnetic resonance transverse relaxation times, permeability, and volumetric magnetic susceptibility to aide in characterization of the Fontainebleau sandstone. Analysis of collected nuclear magnetic resonance data is then compared to other petrophysical studies from literature such as helium porosity and permeability, magnetic susceptibility, and electrical conductivity. I find that the lack of impurities on the grain surfaces of pure quartz samples imparts a lower surface relaxivity as compared to clay containing sandstones and makes nuclear magnetic resonance analysis more complex. Thus, inverted nuclear magnetic resonance data from cleaner outcrop samples incorrectly models pore size distribution without accounting for wider surface relaxivity variation and is improperly used when characterizing the Fontainebleau sandstone. This is further supported by evidence from less

  1. The influence of diagenesis on the reservoir quality of Cambrian and Carboniferous sandstones, southwest Sinai, Egypt

    Science.gov (United States)

    McBride, Earle F.; Abdel-Wahab, Antar; Salem, Alaa M. K.

    1996-04-01

    The diagenetic influence on hydrocarbon reservoir quality was investigated for the Cambrian and Lower Carboniferous sandstones of southwestern Sinai. These quartzose and feldspathic Palaeozoic sandstones were not buried more than 1 to 1.5 km until Late Cretaceous and more recent times, when the most deeply buried rocks may have reached 25 km. Porosity was reduced by compaction from an assumed original 45% to about 26%. In general, both Cambrian and Carboniferous sandstones lost more porosity by compaction (average of 19% for each) than by cementation (average of 17% and 13%, respectively). There is no significant difference in the degree of compaction shown by Cambrian (older, deeper buried) rather than Carboniferous sandstones. Cementation by iron oxide, quartz, calcite and kaolinite reduced porosity to 12-15%, except in silcretes and some ferricretes where porosity was reduced to <5%. Significant secondary porosity was created (5.8 and 5.1 % for Cambrian and Carboniferous sandstones, respectively ) chiefly by dissolution of feldspar. Kaolinite (maximum of 20%) is the most deleterious cement because it has high microporosity, which causes high residual water saturation, and occurs as tiny crystals that have the potential to break loose during rapid fluid flow and block the pore throats. The present-day porosity in these sandstones averages 19% and ranges from 1.5 to 32%. Many sandstone samples (47% of a total of 178 samples) have permeability values higher than 1000 md. The plot of porosity versus the log of permeability has a good correlation indicating that microporosity, even though locally important, does not significantly influence reservoir quality. In spite of their age and the large volumes of groundwater that probably passed through them, these Palaeozoic sandstones retain sufficient porosity and permeability to possess excellent reservoir quality.

  2. Compaction and Permeability Reduction of Castlegate Sandstone under Pore Pressure Cycling

    Science.gov (United States)

    Bauer, S. J.

    2014-12-01

    We investigate time-dependent compaction and permeability changes by cycling pore pressure with application to compressed air energy storage (CAES) in a reservoir. Preliminary experiments capture the impacts of hydrostatic stress, pore water pressure, pore pressure cycling, chemical, and time-dependent considerations near a borehole in a CAES reservoir analog. CAES involves creating an air bubble in a reservoir. The high pressure bubble serves as a mechanical battery to store potential energy. When there is excess grid energy, bubble pressure is increased by air compression, and when there is energy needed on the grid, stored air pressure is released through turbines to generate electricity. The analog conditions considered are depth ~1 km, overburden stress ~20 MPa and a pore pressure ~10MPa. Pore pressure is cycled daily or more frequently between ~10 MPa and 6 MPa, consistent with operations of a CAES facility at this depth and may continue for operational lifetime (25 years). The rock can vary from initially fully-to-partially saturated. Pore pressure cycling changes the effective stress.Jacketed, room temperature tap water-saturated samples of Castlegate Sandstone are hydrostatically confined (20 MPa) and subjected to a pore pressure resulting in an effective pressure of ~10 MPa. Pore pressure is cycled between 6 to 10 MPa. Sample displacement measurements yielded determinations of volumetric strain and from water flow measurements permeability was determined. Experiments ran for two to four weeks, with 2 to 3 pore pressure cycles per day. The Castlegate is a fluvial high porosity (>20%) primarily quartz sandstone, loosely calcite cemented, containing a small amount of clay.Pore pressure cycling induces compaction (~.1%) and permeability decreases (~20%). The results imply that time-dependent compactive processes are operative. The load path, of increasing and decreasing pore pressure, may facilitate local loosening and grain readjustments that results in the

  3. Architectural evidence of dune collapse in the Navajo Sandstone, Zion National Park, Utah

    Science.gov (United States)

    Ford, Colby; Bryant, Gerald; Nick, Kevin E.

    2016-10-01

    The Canyon Overlook Trail of Zion National Park follows an outcrop of Navajo Sandstone, which displays a uniquely well-exposed assemblage of features associated with failure of the lee face of a large eolian dune, and run-out over an expanse of interdune sediments downwind of that bedform. Exposed features include dramatic folds in the interdune succession and a stacked series of thrust sheets incorporating both interdune and overlying dune deposits. Thrust surfaces display consistent strikes, parallel to those of undeformed foresets, and incorporate zones of brittle failure and fluid deformation, including folds overturned in the direction of foreset dip. These features correspond to predictions made by a previous researcher's model of dune collapse, formulated from less fortuitously exposed architectures in the Navajo Sandstone. Unlike the previous model, however, this site preserves distinct indications that the bulk of deformed material accumulated above the level of the contemporary interdune surface, in an aggradational succession. Paleotopographic reconstruction, based on preserved facies relationships at this site, indicates the presence of a large dune, partially encroached upon a well-developed wet interdune succession, made up of two half-meter carbonate mud layers, separated by a meter of medium-grained sand. Trapping of pore water pressure between these mud layers during liquefaction reduced shear strength in this interval, facilitating the collapse of the lee face of the upwind dune into the interdune area, and transmitted resultant shear forces to distal portions of the interdune expanse, in the shallow subsurface. Shear failure developed along bedding planes in the horizontally laminated carbonate muds, which provided both lubrication of the shear surfaces and structural support for the preservation of coherent thrust sheets during production of an imbricated succession of shear zones in the toe portion of the slump. Individual shear surfaces

  4. Effects of Thermal Treatment on the Dynamic Mechanical Properties of Coal Measures Sandstone

    Science.gov (United States)

    Li, Ming; Mao, Xianbiao; Cao, Lili; Pu, Hai; Mao, Rongrong; Lu, Aihong

    2016-09-01

    Many projects such as the underground gasification of coal seams and coal-bed methane mining (exploitation) widely involve the dynamic problems of coal measures sandstone achieved via thermal treatment. This study examines the dynamic mechanical properties of coal measures sandstone after thermal treatment by means of an MTS653 high-temperature furnace and Split Hopkinson pressure bar test system. Experimental results indicate that 500 °C is a transition point for the dynamic mechanical parameters of coal measures sandstone. The dynamic elastic modulus and peak strength increase linearly from 25 to 500 °C while the dynamic peak strain decreases linearly over the same temperature range. The dynamic elastic modulus and peak strength drop quickly from 500 to 800 °C, with a significant increase in the dynamic peak strain over the same temperature range. The rock mechanics are closely linked to material composition and mesoscopic structure. Analysis by X-ray diffraction and scanning electron microscopy indicate that the molecules inside the sandstone increase in density due to the thermal expansion of the material particles, which effectively improves the deformation resistance and carrying capacity of the sandstone and reduces the likelihood of axial deformation. With heat treatment that exceeds 500 °C, the dynamic mechanical properties rapidly weaken due to the decomposition of kaolinite; additionally, hot cracking of the mineral particles within the materials arises from coal sandstone internal porosity, and other defects gradually appear.

  5. Study on pore characteristics and microstructure of sandstones with different grain sizes

    Science.gov (United States)

    Li, Huigui; Li, Huamin; Gao, Baobin; Wang, Wen; Liu, Chuang

    2017-01-01

    The grain sizes have a pronounced influence on the pore characteristics and microstructure of sandstone. This work examined the pore structure and characteristics of three kinds of sandstones with different grain sizes using the scanning electron microscopy (SEM) and nuclear magnetic resonance (NMR) methods and analyzed their grain size distributions, pore size distributions, T2-distributions, and porosity variations. The experimental results showed that sandstones with different grain sizes have significant differences in the microstructures grain size distribution, pore size distribution, T2-distribution, and porosity variation. The results show that coarse, medium and fine sandstones have two peaks in T2-distributions, mean grain size of 398.5, 145.1 and 25.1 μm, respectively, mean pore size of 46.3, 25.9, and 8.4 μm, respectively, porosity of 7.52%, 5.88% and 1.55%, respectively, indicating that both coarse and medium sandstones contain big pores, while fine sandstone contains small pores. This study is of significance for understanding of water migration characteristics in aquifers and gas in coal seams after the working face exploitation.

  6. Brittleness index and seismic rock physics model for anisotropic tight-oil sandstone reservoirs

    Institute of Scientific and Technical Information of China (English)

    Huang Xin-Rui; Huang Jian-Ping; Li Zhen-Chun; Yang Qin-Yong; Sun Qi-Xing; Cui Wei

    2015-01-01

    Brittleness analysis becomes important when looking for sweet spots in tight-oil sandstone reservoirs. Hence, appropriate indices are required as accurate brittleness evaluation criteria. We construct a seismic rock physics model for tight-oil sandstone reservoirs with vertical fractures. Because of the complexities in lithology and pore structure and the anisotropic characteristics of tight-oil sandstone reservoirs, the proposed model is based on the solid components, pore connectivity, pore type, and fractures to better describe the sandstone reservoir microstructure. Using the model, we analyze the brittleness sensitivity of the elastic parameters in an anisotropic medium and establish a new brittleness index. We show the applicability of the proposed brittleness index for tight-oil sandstone reservoirs by considering the brittleness sensitivity, the rock physics response characteristics, and cross-plots. Compared with conventional brittleness indexes, the new brittleness index has high brittleness sensitivity and it is the highest in oil-bearing brittle zones with relatively high porosity. The results also suggest that the new brittleness index is much more sensitive to elastic properties variations, and thus can presumably better predict the brittleness characteristics of sweet spots in tight-oil sandstone reservoirs.

  7. Factors controlling reservoir quality in tertiary sandstones and their significance to geopressured geothermal production

    Energy Technology Data Exchange (ETDEWEB)

    Loucks, R.G.; Richmann, D.L.; Milliken, K.L.

    1981-01-01

    Variable intensity of diagenesis is the factor primarily responsible for contrasting regional reservoir quality of Tertiary sandstones from the upper and lower Texas coast. Detailed comparison of Frio sandstone from the Chocolate Bayou/Danbury Dome area, Brazoria County, and Vicksburg sandstones from the McAllen Ranch Field area, Hidalgo County, reveals that extent of diagenetic modification is most strongly influenced by (1) detrital mineralogy and (2) regional geothermal gradients. The regional reservoir quality of Frio sandstones from Brazoria County is far better than that characterizing Vicksburg sandstones from Hidalgo County, especially at depths suitable for geopressured geothermal energy production. However, in predicting reservoir quality on a site-specific basis, locally variable factors such as relative proportions for porosity types, pore geometry as related to permeability, and local depositional environment must also be considered. Even in an area of regionally favorable reservoir quality, such local factors can significantly affect reservoir quality and, hence, the geothermal production potential of a specific sandstone unit.

  8. Rare earth element geochemistry of groundwater from a deep seated sandstone aquifer, northern Anhui province, China

    Institute of Scientific and Technical Information of China (English)

    Gui Herong; Sun Linhua; Chen Luwang; Chen Song

    2011-01-01

    Deep coal mines in northern Anhui province,China,provide opportunities for tracing the distribution and fractionation of rare earth elements (REEs) in deep seated environments.Major ions,as well as REE concentrations were measured in groundwater from a sandstone aquifer located between -400 and -280 m.Our results indicate that this groundwater consists of Cl·HCO3-Na or Cl·CO3-Na water types with warm temperature (30.1-31.4℃),circumneutral pH (7.27-8.61) and high levels of total dissolved solids (TDS- 1306-2165 mg/L).Concentrations of REEs in groundwater are high as expressed by their Nd concentrations (0.0086-0.018 μg/L).Except for weak heavy REEs (HREE) enrichment relative to light REEs (LREE),the similarity of REE distribution patterns between groundwater and aquifer rock indicate that enrichment of REEs is considered to be controlled by aquifer rock,as well as by their minerals,whereas the fractionation of REEs is controlled by HREE enriched minerals and,to a lesser extent,by inorganic REE complexes.Ce anomalies normalized to Post Archean Average Shale (PAAS) and aquifer rock are weak,which probably reflect the contribution of reduced conditions in combination with pH,rather than a signature of aquifer rock.

  9. Diagenesis, provenance and reservoir quality of Triassic TAGI sandstones from Ourhoud field, Berkine (Ghadames) Basin, Algeria

    Energy Technology Data Exchange (ETDEWEB)

    Rossi, C.; Arribas, J.; Tortosa, A. [Universidad Complutense de Madrid, (Spain). Departamento de Petrologia y Geoquimica; Kalin, O. [Universidad Complutense, Madrid (Spain). Departamento de Paleontologia

    2002-02-01

    The Triassic TAGI (Trias Argilo-Greseux Inferieur) fluvial sandstones are the main oil reservoirs in the Berkine Basin, Algeria. Nonetheless, their provenance and diagenesis, and their impact on reservoir quality, are virtually unknown. Samples from the Ourhoud field, representing the Lower, Middle and Upper TAGI subunits, were studied using a combination of petrographic, mineralogical and geochemical techniques. The Lower TAGI sandstones have an average framework composition of Q{sub 98.3}F{sub 0.6}R{sub 1.1} and 95% of the quartz grains are monocrystalline. By contrast, the Middle-Upper TAGI sandstones have an average framework composition of Q{sub 88.3}F{sub 9.8}R{sub 1.9} and 79% of the quartz grains are monocrystalline. The Lower TAGI quartz arenites derived from Paleozoic siliclastic rocks, whereas the Middle-Upper TAGI subarkoses originated mainly from metamorphic terrains. This change in provenance is a potential criterion for correlation within the TAGI. Also, this change has contributed to the significantly different diagenetic paths followed by the Lower TAGI quartz arenites and the Middle-Upper TAGI subarkoses. Grain-coating illitic clays are abundant in the Lower TAGI, where they exert a critical control on reservoir quality. These clays are interpreted as pedogenic and/or infiltrated in origin and to have had, in part, smectitic precursors. Shallow burial Fe-dolomite cementation was favored in the downthrown block of the field-bounding fault, where it contributed to the poor reservoir quality. Magnesite-siderite cements are multiphase. The earliest generation is composed of Fe-rich magnesite that precipitated during shallow burial from hypersaline fluids with high Mg/Ca ratios, probably refluxed residual brines associated with the Liassic evaporites. Later magnesite-siderite generations precipitated during deeper burial from waters with progressively higher Fe/Mg ratios. Authigenic vermicular kaolin largely consists of dickite that replaced previously

  10. Structural and erosive Effects of Lightning on Sandstone: An Experimental Investigation

    Science.gov (United States)

    Haddad, Houssam; Ebert, Matthias; Kenkmann, Thomas; Thoma, Klaus; Nau, Siegfried; Schäfer, Frank

    2016-04-01

    Recent prognoses predict an average temperature increase of the world's climate of about 1.5 to 2 °C until the end of 21st century. This change leads not only to a rise of the sea level but also to an increase of thunderstorms and therefore to a ~25 percent increase of cloud-to-ground lightning events (Romps et al., 2014). It is known that (i) lightning strikes are able to fragment surface rocks, which probably influences the erosion rates at exposed mountain areas (Knight and Grab, 2014), and (ii) the efficiency of the process increases due to the predicted climate change. However, our knowledge about the electro-mechanical destruction of rocks caused by high energetic lightning is incomplete. In this study, laboratory experiments of lightning strikes were performed in order to understand the fragmentation of rocks and changes to landforms by lightning. The artificial lightning with known electric current was simulated by a high-current generator in the laboratories of the Fraunhofer Ernst-Mach Institute for High-Speed Dynamics (Freiburg, Germany). Different currents were transferred over a distance of ~2mm onto water-saturated sandstones by using a copper cathode (3 experiments; U, I, E, Δt: 6 kV, 200 kA, 0.1 MJ, 0.7 ms; 9 kV, 300 kA, 0.19 MJ, 0.9 ms; 12 kV, 400 kA, 0.35 MJ, 0.5 ms). The damaged sandstones were investigated by means of optical and electron-optical methods as well as by X-ray computed tomography to determine the modes and dimensions of melting and fragmentation. Digital elevation models of craters formed by ejection were obtained by white-light interferometry. The lightning experiments produced small craters (~1 cm in diameter, ~0.5 cm depth) which surfaces and sub-surfaces consist of silicate melts (molten quartz and phyllosilicates). The silicate melts reach several hundred micrometers into the sub-surface and resemble the appearance of natural fulgurites. Melting of quartz indicate temperatures of at least 1650 °C. In addition, the

  11. Tar sandstones in the Parana Basin: a study of the occurrences in the Anhembi Structural High; Arenitos asfalticos na Bacia do Parana: estudo das ocorrencias no Alto Estrutural de Anhembi

    Energy Technology Data Exchange (ETDEWEB)

    Araujo, Carlos Cesar de [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Area de Negocio Internacional], E-mail: ccaraujo@petrobras.com.br; Yamamoto, Jorge Kazuo; Rostirolla, Sidnei Pires

    2005-11-15

    There are tar accumulations in Early Triassic sandstones along the eastern margin of the Parana Basin. The aim of this research work is to explain the tar sandstone occurrences in the Anhembi High. The Anhembi High, where permian mudstones outcrop in a Triassic sandstone area, is a Jurassic-Cretaceous structure related to the reactivation of pre-existing basement faults. Tar was derived from Permian source rocks that matured along the basic sills of the continental flood basalt cover of Serra Geral Formation. This paper examines the habitat of tar accumulation and integrates fieldwork with morpho structural data, digital elevation model, gravity and airborne magnetic data and remote sensing imagery. The interpretation of the structural framework is based primarily on the morpho structural analysis, the distribution of gravity and magnetic anomalies and on a structural field survey. The Anhembi High consists of three blocks with a N50W-trending major axis. Tar sandstone outcrops occur around the Anhembi structure, on its low-lying block and are restricted to the lower Piramboia Formation. The morpho structural interpretation suggests the occurrence of tar sandstones at intermediate positions, between the structural highs and lows. The most likely explanation for these tar accumulations relates oil maturation and migration to the intrusion of Early Cretaceous Serra Geral sills into the Late Permian black shales of the Irati Formation, and subsequent migration along faults and dyke walls into eolian sandstone reservoirs of the Triassic Piramboia Formation. Not only did the basic dykes locally facilitate migration, but there were also places where they constituted barriers to lateral migration. Furthermore, the interdune and fluvial facies of the Piramboia Formation formed local seals and barriers to vertical migration.

  12. Clockwise Rotation and Implications for Northward Drift of the Western Transverse Ranges from Paleomagnetism of the Piuma Member, Sespe Formation, near Malibu, California

    Science.gov (United States)

    Hillhouse, J. W.

    2007-12-01

    New paleomagnetic results from mid-Tertiary sedimentary beds in the Santa Monica Mountains of southern California reinforce the evidence for large-scale rotation of the western Transverse Ranges, originally postulated from observations of basement-structure trends and supported by paleodeclination data from Eocene and younger rocks. Previously published paleomagnetic data indicate that post-Oligocene rotation amounts to 70°-110° clockwise, affecting the Channel Islands, Santa Monica Mountains, and Santa Ynez Mountains. The Sespe Formation near Malibu consists of a lower member dominated by nonmarine sandstone and conglomerate and an upper section, the Piuma Member, which consists of gray-red sandstone and mudstone interbedded with minor tuff and limestone beds. The Piuma Member has a paleomagnetic pole at 36.7°N, 326.7°E (A95min=5.0°, A95max=9.6°), resulting from thermal demagnetization of 34 oriented cores covering beds from Oligocene to Early Miocene age. The data are consistent with significant clockwise rotation (68°±7°) of the region relative to stable North America. Rotation of the western Transverse Ranges is generally viewed as a consequence of Pacific-North American plate interactions after 28 Ma, when east-west subduction gave way to northwest transform motion in southern California. Inclinations from the Piuma study lead to a paleolatitude anomaly of 11°±7°, or a mean northward drift that exceeds generally accepted San Andreas fault displacement by a factor of three. However, analysis of magnetization-direction distributions from this study combined with J. Liddicoat's work at other Sespe Formation sites (total N=131) reveals that sedimentary inclination error, rather than northward drift, may be the primary contributor to the anomaly. Application of the Tauxe and Kent method, which tests the elliptical shape of a given field-direction dataset against a global geomagnetic field model (TK03.GAD), requires mean inclination flattening of

  13. Pore structure characterization of Chang-7 tight sandstone using MICP combined with N2GA techniques and its geological control factors

    Science.gov (United States)

    Cao, Zhe; Liu, Guangdi; Zhan, Hongbin; Li, Chaozheng; You, Yuan; Yang, Chengyu; Jiang, Hang

    2016-11-01

    Understanding the pore networks of unconventional tight reservoirs such as tight sandstones and shales is crucial for extracting oil/gas from such reservoirs. Mercury injection capillary pressure (MICP) and N2 gas adsorption (N2GA) are performed to evaluate pore structure of Chang-7 tight sandstone. Thin section observation, scanning electron microscope, grain size analysis, mineral composition analysis, and porosity measurement are applied to investigate geological control factors of pore structure. Grain size is positively correlated with detrital mineral content and grain size standard deviation while negatively related to clay content. Detrital mineral content and grain size are positively correlated with porosity, pore throat radius and withdrawal efficiency and negatively related to capillary pressure and pore-to-throat size ratio; while interstitial material is negatively correlated with above mentioned factors. Well sorted sediments with high debris usually possess strong compaction resistance to preserve original pores. Although many inter-crystalline pores are produced in clay minerals, this type of pores is not the most important contributor to porosity. Besides this, pore shape determined by N2GA hysteresis loop is consistent with SEM observation on clay inter-crystalline pores while BJH pore volume is positively related with clay content, suggesting N2GA is suitable for describing clay inter-crystalline pores in tight sandstones.

  14. Measuring and predicting reservoir heterogeneity in complex deposystems. The fluvial-deltaic Big Injun Sandstone in West Virginia. Final report, September 20, 1991--October 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Hohn, M.E.; Patchen, D.G.; Heald, M.; Aminian, K.; Donaldson, A.; Shumaker, R.; Wilson, T.

    1994-05-01

    Non-uniform composition and permeability of a reservoir, commonly referred to as reservoir heterogeneity, is recognized as a major factor in the efficient recovery of oil during primary production and enhanced recovery operations. Heterogeneities are present at various scales and are caused by various factors, including folding and faulting, fractures, diagenesis and depositional environments. Thus, a reservoir consists of a complex flow system, or series of flow systems, dependent on lithology, sandstone genesis, and structural and thermal history. Ultimately, however, fundamental flow units are controlled by the distribution and type of depositional environments. Reservoir heterogeneity is difficult to measure and predict, especially in more complex reservoirs such as fluvial-deltaic sandstones. The Appalachian Oil and Natural Gas Research Consortium (AONGRC), a partnership of Appalachian basin state geological surveys in Kentucky, Ohio, Pennsylvania, and West Virginia, and West Virginia University, studied the Lower Mississippian Big Injun sandstone in West Virginia. The Big Injun research was multidisciplinary and designed to measure and map heterogeneity in existing fields and undrilled areas. The main goal was to develop an understanding of the reservoir sufficient to predict, in a given reservoir, optimum drilling locations versus high-risk locations for infill, outpost, or deeper-pool tests.

  15. Geochemical interpretation of the Precambrian basement and overlying Cambrian sandstone on Bornholm, Denmark: Implications for the weathering history

    Science.gov (United States)

    Zhou, Lingli; Friis, Henrik; Yang, Tian; Nielsen, Arne Thorshøj

    2017-08-01

    A geochemical study of the Precambrian basement granites from the Borggård borehole on Bornholm, Denmark, suggests that the granites were moderately weathered (Chemical Index of Alteration-CIA = 66-71) during subaerial exposure in a humid climate. The microcline is well preserved, whereas plagioclase was thoroughly altered to clay minerals (Plagioclase Index of Alteration-PIA = 93-99) which is likely due to its original Ca-rich composition. The primary Fe-Ti accessory minerals were oxidized to hematite and anatase. Evidence from REE distribution patterns and immobile element ratios, e.g. Zr/Hf and Nb/Ta, between the weathered basement granite from the Borggård borehole and regional granitoids on Bornholm, constrains the Svaneke Granite as the original basement lithology. A tau (τ) mass transport model (assuming immobile Ti) was applied to quantify the mass transfer during weathering of the basement granite. The results show a depletion of major elements in the following order: Na > Ca > Mg > Si; Al and Ti are immobile and stay constant; K shows sample dependent enrichment or depletion; Fe is slightly enriched. The Cambrian sandstone overlying the basement in the Borggård borehole, assigned to the Gadeby Member of the Nexø Formation, is feldspathic litharenite-litharenite in composition. Provenance indicators including (Gd/Yb)N, Zr/Hf and Nb/Ta ratios and petrological features indicate that source material was derived from both weathered and fresh basement granite of intermediate composition. The Gadeby Member equivalents in Germany, the basal lower Cambrian Adlergrund Konglomerat Member (AKM) in the offshore G-14 well north of Rügen, and the approximately coeval Lubmin Sandstein Formation (LSF) from the Loissin-1 borehole, mainland Germany, must have been sourced from a basement with compositions comparable to the intermediate group of the regional granitoids on Bornholm. The source materials for the AKM (CIA = 71-72, PIA = 94-96), the Gadeby Member in the

  16. Synkinematic quartz cementation in partially open fractures in sandstones

    Science.gov (United States)

    Ukar, Estibalitz; Laubach, Stephen E.; Fall, Andras; Eichhubl, Peter

    2014-05-01

    Faults and networks of naturally open fractures can provide open conduits for fluid flow, and may play a significant role in hydrocarbon recovery, hydrogeology, and CO2 sequestration. However, sandstone fracture systems are commonly infilled, at least to some degree, by quartz cement, which can stiffen and occlude fractures. Such cement deposits can systematically reduce the overall permeability enhancement due to open fractures (by reducing open fracture length) and result in permeability anisotropies. Thus, it is important to identify the factors that control the precipitation of quartz in fractures in order to identify potential fluid conduits under the present-day stress field. In many sandstones, quartz nucleates syntaxially on quartz grain or cement substrate of the fracture wall, and extends between fracture walls only locally, forming pillars or bridges. Scanning electron microscope cathodoluminescence (SEM-CL) images reveal that the core of these bridges are made up of bands of broken and resealed cement containing wall-parallel fluid inclusion planes. The fluid inclusion-rich core is usually surrounded by a layer of inclusion-poor clear quartz that comprises the lateral cement. Such crack-seal textures indicate that this phase was precipitating while the fractures were actively opening (synkinematic growth). Rapid quartz accumulation is generally believed to require temperatures of 80°C or more. Fluid inclusion thermometry and Raman spectroscopy of two-phase aqueous fluid-inclusions trapped in crack-seal bands may be used to track the P-T-X evolution of pore fluids during fracture opening and crack-seal cementation of quartz. Quartz cement bridges across opening mode fractures in the Cretaceous Travis Peak Formation of the tectonically quiescent East Texas Basin indicate individual fractures opened over a 48 m.y. time span at rates of 16-23 µm/m.y. Similarly, the Upper Cretaceous Mesaverde Group in the Piceance Basin, Colorado contains fractures that

  17. The influence of clay minerals on acoustic properties of sandstones

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, Olav

    1997-12-31

    This thesis aims to provide better understanding of the relationship between the acoustic properties and the petrophysical/mineralogical properties in sand-prone rock. It emphasizes the influence of clay minerals. The author develops a method to deposit clay minerals/mineral aggregates in pore space of a rigid rock framework. Kaolinite aggregates were flushed into porous permeable Bentheimer sandstone to evaluate the effect of pore filling minerals on porosity, permeability and acoustic properties. The compressional velocity was hardly affected by the clay content and it was found that the effect of minor quantities of pore filling minerals may be acoustically modelled as an ideal suspension, where the pore fluid bulk modulus is modified by the bulk modulus of the clay minerals. The influence of clays on acoustic velocities in petroleum reservoir rocks was investigated through ultrasonic measurements of compressional- and shear-waves on core material from reservoir and non-reservoir units on the Norwegian Continental Shelf. The measured velocities decrease as the porosity increases, but are not strongly dependent on the clay content. The measured velocities are less dependent on the petrophysical and lithological properties than indicated by previous authors and published mathematical models, and stiffness reduction factors are introduced in two of the models to better match the data. Velocities are estimated along the wellbores based on non-sonic well logs and reflect well the actual sonic log well measurements. In some wells the compressional velocity cannot be modelled correctly by the models suggested. Very high compressional wave anisotropy was measured in the dry samples at atmospheric conditions. As the samples were saturated, the anisotropy was reduced to a maximum of about 30% and decreases further upon pressurization. Reservoir rocks retrieved from 2500 m are more stress dependent than those retrieved from less than 200 m depth. 168 refs., 117 figs., 24

  18. Predicting cement distribution in geothermal sandstone reservoirs based on estimates of precipitation temperatures

    Science.gov (United States)

    Olivarius, Mette; Weibel, Rikke; Whitehouse, Martin; Kristensen, Lars; Hjuler, Morten L.; Mathiesen, Anders; Boyce, Adrian J.; Nielsen, Lars H.

    2016-04-01

    Exploitation of geothermal sandstone reservoirs is challenged by pore-cementing minerals since they reduce the fluid flow through the sandstones. Geothermal exploration aims at finding sandstone bodies located at depths that are adequate for sufficiently warm water to be extracted, but without being too cemented for warm water production. The amount of cement is highly variable in the Danish geothermal reservoirs which mainly comprise the Bunter Sandstone, Skagerrak and Gassum formations. The present study involves bulk and in situ stable isotope analyses of calcite, dolomite, ankerite, siderite and quartz in order to estimate at what depth they were formed and enable prediction of where they can be found. The δ18O values measured in the carbonate minerals and quartz overgrowths are related to depth since they are a result of the temperatures of the pore fluid. Thus the values indicate the precipitation temperatures and they fit the relative diagenetic timing identified by petrographical observations. The sandstones deposited during arid climatic conditions contain calcite and dolomite cement that formed during early diagenesis. These carbonate minerals precipitated as a response to different processes, and precipitation of macro-quartz took over at deeper burial. Siderite was the first carbonate mineral that formed in the sandstones that were deposited in a humid climate. Calcite began precipitating at increased burial depth and ankerite formed during deep burial and replaced some of the other phases. Ankerite and quartz formed in the same temperature interval so constrains on the isotopic composition of the pore fluid can be achieved. Differences in δ13C values exist between the sandstones that were deposited in arid versus humid environments, which suggest that different kinds of processes were active. The estimated precipitation temperatures of the different cement types are used to predict which of them are present in geothermal sandstone reservoirs in

  19. GREYBULL SANDSTONE PETROLEUM POTENTIAL ON THE CROW INDIAN RESERVATION, SOUTH-CENTRAL MONTANA

    Energy Technology Data Exchange (ETDEWEB)

    David A. Lopez

    2000-12-14

    Evaluation of the Lower Cretaceous Greybull Sandstone on the Crow Indian Reservation for potential stratigraphic traps in the valley-fill sandstone was the focus of this project. The Crow Reservation area, located in south-central Montana, is part of the Rocky Mountain Foreland structural province, which is characterized by Laramide uplifts and intervening structural basins. The Pryor and Bighorn mountains, like other foreland uplifts, are characterized by asymmetrical folds associated with basement-involved reverse faults. The reservation area east of the mountains is on the northwestern flank of the Powder River Basin. Therefore, regional dips are eastward and southeastward; however, several prominent structural features interrupt these regional dips. The nearly 4,000 mi{sup 2} reservation is under explored but has strong potential for increased oil and gas development. Oil and gas production is well established in the Powder River Basin of Wyoming to the south as well as in the areas north and west of the reservation. However, only limited petroleum production has been established within the reservation. Geologic relations and trends indicate strong potential for oil and gas accumulations, but drilling has been insufficient for their discovery. The Greybull Sandstone, which is part of the transgressive systems tract that includes the overlying Fall River Sandstone, was deposited on a major regional unconformity. The erosional surface at the base of the Greybull Sandstone is the +100 Ma, late Aptian-Early Albian regional unconformity of Weimer (1984). This lowstand erosional surface was controlled by a basin-wide drop in sea level. In areas where incised Greybull channels are absent, the lowstand erosional unconformity is at the base of the Fall River Sandstone and equivalent formations. During the pre-Greybull lowstand, sediment bypassed this region. In the subsequent marine transgression, streams began to aggrade and deposit sand of the lower Greybull Sandstone

  20. Team Member Training Manual.

    Science.gov (United States)

    1998-07-01

    minutes a "facilitator" obtains one idea from each member in turn and writes that idea on a flip chart . No discussion takes place during this step. 4...Step three is repeated until all ideas are listed on the flip chart . 5. Each idea is discussed. Participants seek clarification and express support

  1. Statistical analyses on sandstones: Systematic approach for predicting petrographical and petrophysical properties

    Science.gov (United States)

    Stück, H. L.; Siegesmund, S.

    2012-04-01

    Sandstones are a popular natural stone due to their wide occurrence and availability. The different applications for these stones have led to an increase in demand. From the viewpoint of conservation and the natural stone industry, an understanding of the material behaviour of this construction material is very important. Sandstones are a highly heterogeneous material. Based on statistical analyses with a sufficiently large dataset, a systematic approach to predicting the material behaviour should be possible. Since the literature already contains a large volume of data concerning the petrographical and petrophysical properties of sandstones, a large dataset could be compiled for the statistical analyses. The aim of this study is to develop constraints on the material behaviour and especially on the weathering behaviour of sandstones. Approximately 300 samples from historical and presently mined natural sandstones in Germany and ones described worldwide were included in the statistical approach. The mineralogical composition and fabric characteristics were determined from detailed thin section analyses and descriptions in the literature. Particular attention was paid to evaluating the compositional and textural maturity, grain contact respectively contact thickness, type of cement, degree of alteration and the intergranular volume. Statistical methods were used to test for normal distributions and calculating the linear regression of the basic petrophysical properties of density, porosity, water uptake as well as the strength. The sandstones were classified into three different pore size distributions and evaluated with the other petrophysical properties. Weathering behavior like hygric swelling and salt loading tests were also included. To identify similarities between individual sandstones or to define groups of specific sandstone types, principle component analysis, cluster analysis and factor analysis were applied. Our results show that composition and porosity

  2. Sedimentological reservoir characteristics of the Paleocene fluvial/lacustrine Yabus Sandstone, Melut Basin, Sudan

    Science.gov (United States)

    Mahgoub, M. I.; Padmanabhan, E.; Abdullatif, O. M.

    2016-11-01

    Melut Basin in Sudan is regionally linked to the Mesozoic-Cenozoic Central and Western African Rift System (CWARS). The Paleocene Yabus Formation is the main oil producing reservoir in the basin. It is dominated by channel sandstone and shales deposited in fluvial/lacustrine environment during the third phase of rifting in the basin. Different scales of sedimentological heterogeneities influenced reservoir quality and architecture. The cores and well logs analyses revealed seven lithofacies representing fluvial, deltaic and lacustrine depositional environments. The sandstone is medium to coarse-grained, poorly to moderately-sorted and sub-angular to sub-rounded, arkosic-subarkosic to sublitharenite. On the basin scale, the Yabus Formation showed variation in sandstone bodies, thickness, geometry and architecture. On macro-scale, reservoir quality varies vertically and laterally within Yabus Sandstone where it shows progressive fining upward tendencies with different degrees of connectivity. The lower part of the reservoir showed well-connected and amalgamated sandstone bodies, the middle to the upper parts, however, have moderate to low sandstone bodies' connectivity and amalgamation. On micro-scale, sandstone reservoir quality is directly affected by textures and diagenetic changes such as compaction, cementation, alteration, dissolution and kaolinite clays pore fill and coat all have significantly reduced the reservoir porosity and permeability. The estimated porosity in Yabus Formation ranges from 2 to 20% with an average of 12%; while permeability varies from 200 to 500 mD and up to 1 Darcy. The understanding of different scales of sedimentological reservoir heterogeneities might contribute to better reservoir quality prediction, architecture, consequently enhancing development and productivity.

  3. Mechanistic study of wettability alteration of oil-wet sandstone surface using different surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Hou, Bao-feng, E-mail: hbf370283@163.com; Wang, Ye-fei; Huang, Yong

    2015-03-01

    Graphical abstract: Zeta potential of oil-wet quartz powder treated with different surfactants at different concentrations. - Highlights: • Mechanisms of wettability alteration during surfactant flooding were studied. • Different analytical instruments were used to study sandstone wettability alteration. • Surfactants’ structure plays a great role in wettability alteration of solid surface. • CTAB irreversibly desorbs carboxylic acid from solid surface by ionic interaction. • Cationic surfactant is more effective in wettability alteration of sandstone surface. - Abstract: Different analytical methods including Fourier transform infrared (FTIR), atomic force microscopy (AFM), zeta potential measurements, contact angle measurements and spontaneous imbibition tests were utilized to make clear the mechanism for wettability alteration of oil-wet sandstone surface using different surfactants. Results show that among three types of surfactants including cationic surfactants, anionic surfactants and nonionic surfactants, the cationic surfactant CTAB demonstrates the best effect on the wettability alteration of oil-wet sandstone surface. The positively charged head groups of CTAB molecules and carboxylic acid groups from crude oil could interact to form ion pairs, which could be desorbed from the solid surface and solubilized into the micelle formed by CTAB. Thus, the water-wetness of the solid surface is improved. Nonionic surfactant TX-100 could be adsorbed on oil-wet sandstone surface through hydrogen bonds and hydrophobic interaction to alter the wettability of oil-wet solid surface. The wettability alteration of oil-wet sandstone surface using the anionic surfactant POE(1) is caused by hydrophobic interaction. Due to the electrostatic repulsion between the anionic surfactant and the negatively charged surface, POE(1) shows less effect on the wettability alteration of oil-wet sandstone surface.

  4. Evidence of Multi-Stage Hydrocarbon Charging and Biodegradation of the Silurian Asphaltic Sandstones in the Tarim Basin, China

    Institute of Scientific and Technical Information of China (English)

    刘洛夫

    2002-01-01

    Asphalts distributed widely in the Silurian sandstones of the Tarim Basin include dry asphalt, soft asphalt and heavy oil. These asphaltic sandstones underwent multi-episodic sedimentary and tectonic events, and their occurrence is diverse and complex, being mixed with normal oil usually. So far, very little work has been done on the asphaltic sandstone origin and hydrocarbon charging ages. After detailed study on the Silurian sandstones, the following highlights were obtained from the analytical results: distribution of the mixed asphalt, heavy oil and normal oil in the Silurian sandstones is the result of multi-stage hydrocarbon charging from the Lower Paleozoic marine source rocks; the characters of asphalts formed from oils of different charging ages are of difference; the most important process constraining.the asphaltic sandstone origin is thought to be biodegradation.

  5. Lack of inhibiting effect of oil emplacement on quartz cementation: Evidence from Cambrian reservoir sandstones, Paleozoic Baltic Basin

    DEFF Research Database (Denmark)

    Molenaar, Nicolaas; Cyziene, Jolanta; Sliaupa, Saulius;

    2008-01-01

    Currently, the question of whether or not the presence of oil in sandstone inhibits quartz cementation and preserves porosity is still debated. Data from a number of Cambrian sandstone oil fields and dry fields have been studied to determine the effects of oil emplacement on quartz cementation...... cementation is derived from internal sources. Rather, in spite of large variation in porosity and quartz cement content, a regular pattern of porosity decrease is related to increasing temperature or depth. The observed heterogeneity is due to local factors that influence the precipitation of quartz cement......, including sandstone architecture, i.e., distribution of shales within the sandstone bodies, and sandstone thickness. Heterogeneity is inherent to sandstone architecture and to the fact that silica for quartz cementation is derived from heterogeneously distributed local pressure solution. Models predicting...

  6. Structural evolution of fault zones in sandstone by multiple deformation mechanisms: Moab fault, southeast Utah

    Science.gov (United States)

    Davatzes, N.C.; Eichhubl, P.; Aydin, A.

    2005-01-01

    Faults in sandstone are frequently composed of two classes of structures: (1) deformation bands and (2) joints and sheared joints. Whereas the former structures are associated with cataclastic deformation, the latter ones represent brittle fracturing, fragmentation, and brecciation. We investigated the distribution of these structures, their formation, and the underlying mechanical controls for their occurrence along the Moab normal fault in southeastern Utah through the use of structural mapping and numerical elastic boundary element modeling. We found that deformation bands occur everywhere along the fault, but with increased density in contractional relays. Joints and sheared joints only occur at intersections and extensional relays. In all locations , joints consistently overprint deformation bands. Localization of joints and sheared joints in extensional relays suggests that their distribution is controlled by local variations in stress state that are due to mechanical interaction between the fault segments. This interpretation is consistent with elastic boundary element models that predict a local reduction in mean stress and least compressive principal stress at intersections and extensional relays. The transition from deformation band to joint formation along these sections of the fault system likely resulted from the combined effects of changes in remote tectonic loading, burial depth, fluid pressure, and rock properties. In the case of the Moab fault, we conclude that the structural heterogeneity in the fault zone is systematically related to the geometric evolution of the fault, the local state of stress associated with fault slip , and the remote loading history. Because the type and distribution of structures affect fault permeability and strength, our results predict systematic variations in these parameters with fault evolution. ?? 2004 Geological Society of America.

  7. Reservoir Characterization of Bridgeport and Cypress Sandstones in Lawrence Field Illinois to Improve Petroleum Recovery by Alkaline-Surfactant-Polymer Flood

    Energy Technology Data Exchange (ETDEWEB)

    Seyler, Beverly; Grube, John; Huff, Bryan; Webb, Nathan; Damico, James; Blakley, Curt; Madhavan, Vineeth; Johanek, Philip; Frailey, Scott

    2012-12-21

    were used to better understand porosity and permeability trends in the region and to characterize barriers and define flow units. Diagenetic alterations that impact porosity and permeability include development of quartz overgrowths, sutured quartz grains, dissolution of feldspar grains, formation of clay mineral coatings on grains, and calcite cementation. Many of these alterations are controlled by facies. Mapping efforts identified distinct flow units in the northern part of the field showing that the Pennsylvanian Bridgeport consists of a series of thick incised channel fill sequences. The sandstones are about 75-150 feet thick and typically consist of medium grained and poorly sorted fluvial to distributary channel fill deposits at the base. The sandstones become indistinctly bedded distributary channel deposits in the main part of the reservoir before fining upwards and becoming more tidally influenced near their top. These channel deposits have core permeabilities ranging from 20 md to well over 1000 md. The tidally influenced deposits are more compartmentalized compared to the thicker and more continuous basal fluvial deposits. Fine grained sandstones that are laterally equivalent to the thicker channel type deposits have permeabilities rarely reaching above 250 md. Most of the unrecovered oil in Lawrence Field is contained in Pennsylvanian Age Bridgeport sandstones and Mississippian Age Cypress sandstones. These reservoirs are highly complex and compartmentalized. Detailed reservoir characterization including the development of 3-D geologic and geocellular models of target areas in the field were completed to identify areas with the best potential to recover remaining reserves including unswept and by-passed oil. This project consisted of tasks designed to compile, interpret, and analyze the data required to conduct reservoir characterization for the Bridgeport and Cypress sandstones in pilot areas in anticipation of expanded implementation of ASP flooding in

  8. Offers for our members

    CERN Multimedia

    Staff Association

    2017-01-01

    Summer is coming, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 24 € instead of 30 €. Access to Aqualibi: 5 € instead of 6 € on presentation of your SA member ticket. Free for children under 100 cm. Car park free. * * * * * Aquaparc : Day ticket: – Children: 33 CHF instead of 39 CHF – Adults : 33 CHF instead of 49 CHF Bonus! Free for children under 5.

  9. Offers for our members

    CERN Multimedia

    Staff Association

    2017-01-01

    Summer is here, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 24 € instead of 30 €. Access to Aqualibi: 5 € instead of 6 € on presentation of your SA member ticket. Free for children under 100 cm. Car park free. * * * * * Aquaparc : Day ticket: – Children: 33 CHF instead of 39 CHF – Adults : 33 CHF instead of 49 CHF Bonus! Free for children under 5.

  10. 建111井致密砂岩气显示录测井解释研究%On Study of Logging Interpretation of Tight Sandstone Gas Show in Jian Well 111

    Institute of Scientific and Technical Information of China (English)

    张琼; 张伟; 夏敬民; 李光华

    2012-01-01

    致密砂岩气属于非常规天然气资源家族的一员,其储层孔隙度低、渗透率低、随钻录井气测显示弱、气水关系复杂。这些特征,给录测井解释评价带来诸多需要攻关与认识的技术难题。在建南地区首口致密砂岩气勘探开发试验井—建111井,江汉录测井人员于须家河组须六段致密砂岩储层发现并解释典型致密砂岩气层1层厚9.0m,完井测试,日产天然气3 000m3。须六段致密砂岩气的成功解释评价,丰富和验证了现有的录测井致密砂岩气解释评价方法,为下步该地区致密砂岩气开发录测井解释评价积累一定的实践经验。%Tight sandstone gas belongs to an unconventional gas resource.Its reservoir has a low void ratio and permeability.The show effect for gas survey in well drilling and logging is weak and gas-water relation is complicated.All this has brought problems technologically to logging interpretation and evaluation which need to be understood and solved.In the process of exploring and developing the first test well(Jian Well 111) with tight sandstone gas in Jiannan area,Jianghan well logging staff have discovered and interpreted typical tight sandstone gas reservoir of 9.0 m thickness per layer in tight sandstone reservoir of Member Xu 6 in Xujiahe Formation.Output of natural gas a day reaches 3000m3 during well completing test.Success in interpreting and evaluating tight sandstone gas of Member Xu 6 has enriched and checked existing evaluation method,and accumulated some practical experience for well logging interpretation and evaluation in the next development of tight sandstone gas in Jiannan area.

  11. [Comment on] BOSP members

    Science.gov (United States)

    Richman, Barbara T.

    The new Board on Ocean Science and Policy (BOSP) (Eos, June 7, 1983, p. 402) met for the first time on May 4. John B. Slaughter, former director of the National Science Foundation and now chancellor of the University of Maryland in College Park, is the board's chairman. Other board members are D. James Baker, Jr. (University of Washington, Seattle); Kirk Bryan (Geophysical Fluid Dynamics Laboratory, Princeton University); John P. Craven (University of Hawaii); Charles L. Drake (Dartmouth College); Paul M. Fye (Woods Hole Oceanographic Institution); Edward D. Goldberg (Scripps Institution of Oceanography); G. Ross Heath (Oregon State University); Judith T. Kildow (Massachusetts Institute of Technology); John A. Knauss (University of Rhode Island); James J. McCarthy (Museum of Comparative Zoology, Harvard University); H. William Menard (Scripps Institution of Oceanography); C. Barry Raleigh (Lamont-Doherty Geological Observatory); Roger Revelle (University of California, San Diego); David A. Ross (Woods Hole Oceanographic Institution); Brian J. Rothschild (University of Maryland); William M. Sackett (University of South Florida); John H. Steele (Woods Hole Oceanographic Institution); and Carl Wunsch (MIT). Wallace Broecker (Lamont-Doherty Geological Observatory), an original board member, resigned after the first meeting. Broecker told Eos that combining the science and policy boards resulted in a new board whose mission is too broad. A new board member will be appointed in Broecker's place

  12. Sedimentary and petrofacies analyses of the Amasiri Sandstone, southern Benue Trough, Nigeria: Implications for depositional environment and tectonic provenance

    Science.gov (United States)

    Okoro, A. U.; Igwe, E. O.; Nwajide, C. S.

    2016-11-01

    This study was undertaken to determine the depositional environment, provenance and tectonic setting for the Turonian Amasiri Sandstone, southern Benue Trough, Nigeria, using lithofacies analysis and re-appraisal of petrography of the sandstones. Local stratigraphy and field relationships show a thick succession of shales alternating with elongate/parallel sandstone ridges extending eastwards from Akpoha to Amasiri through Itigidi and Ugep to Apiapum areas. Lithofacies analysis reveals 9 lithofacies suggestive of storm (mass flow) and tidal shelf processes. These include dark grey to black laminated shale/silty mudstones, bioturbated mudstones, coquinoid limestones, very fine-grained bioturbated sandstones with shell hash/debris in places and limestone rip-up clasts, massive and chaotic sandy conglomerate with rip - up clasts, fine to medium-grained, parallel laminated sandstone, hummocky cross-stratified, massive, medium to coarse-grained sandstones, medium to very coarse-grained, planar cross-bedded sandstone, with clay-draped foresets and Ophiomorpha burrows, and coarse-grained trough cross-bedded sandstone. Petrofacies analysis identifies the sandstones as feldspathic and arkosic arenites. Ternary plot of framework mineralogy indicates derivation from an uplifted continental block related to the nearby Oban Massif and Cameroon Basement Complex.

  13. Estimation of uranium migration parameters in sandstone aquifers.

    Science.gov (United States)

    Malov, A I

    2016-03-01

    The chemical composition and isotopes of carbon and uranium were investigated in groundwater samples that were collected from 16 wells and 2 sources in the Northern Dvina Basin, Northwest Russia. Across the dataset, the temperatures in the groundwater ranged from 3.6 to 6.9 °C, the pH ranged from 7.6 to 9.0, the Eh ranged from -137 to +128 mV, the total dissolved solids (TDS) ranged from 209 to 22,000 mg L(-1), and the dissolved oxygen (DO) ranged from 0 to 9.9 ppm. The (14)C activity ranged from 0 to 69.96 ± 0.69 percent modern carbon (pmC). The uranium content in the groundwater ranged from 0.006 to 16 ppb, and the (234)U:(238)U activity ratio ranged from 1.35 ± 0.21 to 8.61 ± 1.35. The uranium concentration and (234)U:(238)U activity ratio increased from the recharge area to the redox barrier; behind the barrier, the uranium content is minimal. The results were systematized by creating a conceptual model of the Northern Dvina Basin's hydrogeological system. The use of uranium isotope dating in conjunction with radiocarbon dating allowed the determination of important water-rock interaction parameters, such as the dissolution rate:recoil loss factor ratio Rd:p (a(-1)) and the uranium retardation factor:recoil loss factor ratio R:p in the aquifer. The (14)C age of the water was estimated to be between modern and >35,000 years. The (234)U-(238)U age of the water was estimated to be between 260 and 582,000 years. The Rd:p ratio decreases with increasing groundwater residence time in the aquifer from n × 10(-5) to n × 10(-7) a(-1). This finding is observed because the TDS increases in that direction from 0.2 to 9 g L(-1), and accordingly, the mineral saturation indices increase. Relatively high values of R:p (200-1000) characterize aquifers in sandy-clayey sediments from the Late Pleistocene and the deepest parts of the Vendian strata. In samples from the sandstones of the upper part of the Vendian strata, the R:p value is ∼ 24, i.e., sorption processes are

  14. Interaction of oil components and clay minerals in reservoir sandstones

    Energy Technology Data Exchange (ETDEWEB)

    Changchun Pan; Linping Yu; Guoying Sheng; Jiamo Fu [Chinese Academy of Sciences, State Key Lab. of Organic Geochemistry, Wushan, Guangzhou (China); Jianhui Feng; Yuming Tian [Chinese Academy of Sciences, State Key Lab. of Organic Geochemistry, Wushan, Guangzhou (China); Zhongyuan Oil Field Co., Puyang, Henan (China); Xiaoping Luo [Zhongyuan Oil Field Co., Puyang, Henan (China)

    2005-04-15

    The free oil (first Soxhlet extract) and adsorbed oil (Soxhlet extract after the removal of minerals) obtained from the clay minerals in the <2 {mu}m size fraction as separated from eight hydrocarbon reservoir sandstone samples, and oil inclusions obtained from the grains of seven of these eight samples were studied via GC, GC-MS and elemental analyses. The free oil is dominated by saturated hydrocarbons (61.4-87.5%) with a low content of resins and asphaltenes (6.0-22.0% in total) while the adsorbed oil is dominated by resins and asphaltenes (84.8-98.5% in total) with a low content of saturated hydrocarbons (0.6-9.5%). The inclusion oil is similar to the adsorbed oil in gross composition, but contains relatively more saturated hydrocarbons (16.87-31.88%) and less resins and asphaltenes (62.30-78.01% in total) as compared to the latter. Although the amounts of both free and adsorbed oils per gram of clay minerals varies substantially, the residual organic carbon content in the clay minerals of the eight samples, after the free oil extraction, is in a narrow range between 0.537% and 1.614%. From the decrease of the percentage of the extractable to the total of this residual organic matter of the clay minerals with burial depth it can be inferred that polymerization of the adsorbed polar components occurs with the increase of the reservoir temperature. The terpane and sterane compositions indicate that the oil adsorbed onto the clay surfaces appears to be more representative of the initial oil charging the reservoir than do the oil inclusions. This phenomenon could possibly demonstrate that the first oil charge preferentially interacts with the clay minerals occurring in the pores and as coatings around the grains. Although the variation of biomarker parameters between the free and adsorbed oils could be ascribed to the compositional changes of oil charges during the filling process and/or the differential maturation behaviors of these two types of oils after oil

  15. Factors controlling reservoir quality in tertiary sandstones and their significance to geopressured geothermal production. Annual report, May 1, 1979-May 31, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Loucks, R.G.; Richmann, D.L.; Milliken, K.L.

    1980-07-01

    Differing extents of diagenetic modification is the factor primarily responsible for contrasting regional reservoir quality of Tertiary sandstones from the Upper and Lower Texas Gulf Coast. Detailed comparison of Frio sandstones from the Chocolate Bayou/Danbury Dome area, Brazoria County, and Vicksburg sandstones from the McAllen Ranch Field area, Hidalgo County, reveals that extent of diagenetic modification is most strongly influenced by (1) detrital mineralogy and (2) regional geothermal gradients. Vicksburg sandstones from the McAllen Ranch Field area are less stable, chemically and mechanically, than Frio sandstones from the Chocolate Bayou/Danbury dome area. Vicksburg sandstones are mineralogically immature and contain greater proportions of feldspars and rock fragments than do Frio sandstones. Thr reactive detrital assemblage of Vicksubrg sandstones is highly susceptible to diagenetic modification. Susceptibility is enhanced by higher than normal geothermal gradients in the McAllen Ranch Field area. Thus, consolidation of Vicksburg sandstones began at shallower depth of burial and precipitation of authigenic phases (especially calcite) was more pervasive than in Frio sandstones. Moreover, the late-stage episode of ferroan calcite precipitation that occluded most secondary porosity in Vicksburg sandstones did not occur significantly in Frio sandstones. Therefore, regional reservoir quality of Frio sandstones from Brazoria County is far better than that characterizing Vicksburg sandstones from Hidalgo County, especially at depths suitable for geopressured geothermal energy production.

  16. Stratigraphy and petroleum potential of Trout Creek and Twentymile sandstones (Upper Cretaceous), Sand Wash Basin, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Siepman, B.R.

    1985-05-01

    The Trout Creek and Twentymile Sandstones (Mesaverde Group) in Moffat and Routt Counties, Colorado, are thick, upward-coarsening sequences that were deposited along the western margin of the Western Interior basin during Campanian time. These units trend northeast-southwest and undergo a facies change to coal-bearing strata on the northwest. Surface data collected along the southeastern rim of the Sand Wash basin were combined with well-log data from approximately 100 drill holes that have penetrated the Trout Creek or Twentymile in the subsurface. The sandstones exhibit distinctive vertical profiles with regard to grain size, sedimentary structures, and biogenic structures. A depositional model that incorporates the key elements of the modern Nile River (northeast Africa) and Nayarit (west-central Mexico) coastal systems is proposed for the Trout Creek and Twentymile sandstones and associated strata. The model depicts a wave-dominated deltaic, strand-plain, and barrier-island system. Depositional cycles are asymmetrical in cross section as they are largely progradational and lack significant transgressive deposits. Source rock-reservoir rock relationships are ideal as marine shales underlie, and coal-bearing strata overlie sheetlike reservoir sandstones. Humic coal, the dominant source of Mesaverde gas, generates major quantities of methane upon reaching thermal maturity. Existing Mesaverde gas fields are largely structural traps, but stratigraphic and combination traps may prove to be equally important. The sparsely drilled deeper part of the basin warrants testing as large, overpressured-gas accumulations in tight-sandstone reservoirs are likely to be found.

  17. The impact of reservoir conditions and rock heterogeneity on multiphase flow in CO2-brine-sandstone systems

    Science.gov (United States)

    Krevor, S. C.; Reynolds, C. A.; Al-Menhali, A.; Niu, B.

    2015-12-01

    Capillary strength and multiphase flow are key for modeling CO2 injection for CO2 storage. Past observations of multiphase flow in this system have raised important questions about the impact of reservoir conditions on flow through effects on wettability, interfacial tension and fluid-fluid mass transfer. In this work we report the results of an investigation aimed at resolving many of these outstanding questions for flow in sandstone rocks. The drainage capillary pressure, drainage and imbibition relative permeability, and residual trapping [1] characteristic curves have been characterized in Bentheimer and Berea sandstone rocks across a pressure range 5 - 20 MPa, temperatures 25 - 90 C and brine salinities 0-5M NaCl. Over 30 reservoir condition core flood tests were performed using techniques including the steady state relative permeability test, the semi-dynamic capillary pressure test, and a new test for the construction of the residual trapping initial-residual curve. Test conditions were designed to isolate effects of interfacial tension, viscosity ratio, density ratio, and salinity. The results of the tests show that, in the absence of rock heterogeneity, reservoir conditions have little impact on flow properties, consistent with continuum scale multiphase flow theory for water wet systems. The invariance of the properties is observed, including transitions of the CO2 from a gas to a liquid to a supercritical fluid, and in comparison with N2-brine systems. Variations in capillary pressure curves are well explained by corresponding changes in IFT although some variation may reflect small changes in wetting properties. The low viscosity of CO2at certain conditions results in sensitivity to rock heterogeneity. We show that (1) heterogeneity is the likely source of uncertainty around past relative permeability observations and (2) that appropriate scaling of the flow potential by a quantification of capillary heterogeneity allows for the selection of core flood

  18. Offers for our members

    CERN Multimedia

    Staff Association

    2016-01-01

    Summer is here, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 23 € instead of 29 €. Access to Aqualibi: 5 € instead of 6 € on presentation of your SA member ticket. Free for children (3-11 years old) before 12:00 p.m. Free for children under 3, with limited access to the attractions. Car park free. * * * * * Aquaparc : Day ticket: – Children: 33 CHF instead of 39 CHF – Adults : 33 CHF instead of 49 CHF Bonus! Free for children under 5.

  19. Offers for our members

    CERN Multimedia

    Staff Association

    2016-01-01

    Summer is here, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 23 € instead of 29 €. Access to Aqualibi: 5 € instead of 6 € on presentation of your SA member ticket. Free for children (3-11 years old) before 12:00 p.m. Free for children under 3, with limited access to the attractions. Car park free. * * * * * Aquaparc : Day ticket: – Children: 33 CHF instead of 39 CHF – Adults : 33 CHF instead of 49 CHF Bonus! Free for children under 5.

  20. Offers for our members

    CERN Multimedia

    Staff Association

    2015-01-01

    Summer is here, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 21,50 € instead of 27 €. Access to Aqualibi: 5 € instead of 6 € on presentation of your SA member ticket. Free for children (3-11 years old) before 12:00 p.m. Free for children under 3, with limited access to the attractions. Car park free. * * * * * Aquaparc : Day ticket: – Children: 33 CHF instead of 39 CHF – Adults : 33 CHF instead of 49 CHF Bonus! Free for children under 5.

  1. Offers for our members

    CERN Multimedia

    Staff Association

    2013-01-01

    Summer is here, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 21 € instead of 26 €. Access to Aqualibi: 5 € instead of 8 € on presentation of your SA member ticket. Free for children (3-11 years old) before 12 h 00. Free for children under 3, with limited access to the attractions. Car park free. * * * * * Aquaparc : Day ticket: – Children: 30 CHF instead of 39 CHF – Adults : 36 CHF instead of 49 CHF Bonus! Free for children under 5.

  2. Element mobility during diagenesis: sulphate cementation of Rotliegend sandstones, Southern North Sea

    Energy Technology Data Exchange (ETDEWEB)

    Gluyas, J. [BP Venezuela, Caracas (Venezuela); Jolley, L.; Primmer, T. [BP Exploration, Aberdeen (United Kingdom)

    1998-11-01

    Several wells in the Amethyst gas field of the North Sea`s Southern Basin are poor producers and have been since they were drilled. The lack of gas flow from these wells is due to pervasive cementation of the Rotliegend sandstone reservoir by either anhydrite and/or barite. Both minerals precipitated late in the diagenetic history of the sandstones. Such cements form up to 20% of the total rock. Isotopic and geochemical evidence indicate that the source of the elements for these sulphate cements was outside the Rotliegend sandstone. The sulphur and oxygen isotope data for the anhydrite and barite are unlike those which could have precipitated in Lower Permian times from an evaporating marine basin. Both the timing and distribution of these cements is taken to indicate that faulting allowed, or indeed promoted, mixing of sulphate-rich and barium-rich formation waters derived from the Zechstein and Carboniferous, respectively. (author)

  3. Petrography and Diagenesis of Palaeocene -Eocene Sandstones in the Siri Canyon, Danish North Sea

    DEFF Research Database (Denmark)

    Kazerouni, Afsoon Moatari

    it is generally associated with thick coatings of opal/microquartz on the detrital framework grains.   This study also presents the occurrence and compositional variance of the authigenic zeolites in the Siri Canyon sandstones, and discusses the physico-chemical conditions, which prevailed during formation...... are microquartz, large syntaxial quartz overgrowth, calcite, and chlorite.    Chlorite forms an intra-reservoir hydrocarbon seal, and our study demonstrates the influence of early diagenetic quartz on the formation of the chlorite seal.  Early opal and microquartz are precipitated close to shale contacts...... and prevent the interaction between abundant detrital glaucony and pore-fluid and thus the formation of grain-coating berthierine.  It also preserves porosity and permeability in marginal and isolated parts of the sandstone. In other parts of the sandstone grain coating berthierine precipitated...

  4. Experimental and Numerical Investigations on Strength and Deformation Behavior of Cataclastic Sandstone

    Science.gov (United States)

    Zhang, Y.; Shao, J. F.; Xu, W. Y.; Zhao, H. B.; Wang, W.

    2015-05-01

    This work is devoted to characterization of the deformation and strength properties of cataclastic sandstones. Before conducting mechanical tests, the physical properties were first examined. These sandstones are characterized by a loose damaged microstructure and poorly cemented contacts. Then, a series of mechanical tests including hydrostatic, uniaxial, and triaxial compression tests were performed to study the mechanical strength and deformation of the sandstones. The results obtained show nonlinear stress-strain responses. The initial microcracks are closed at hydrostatic stress of 2.6 MPa, and the uniaxial compressive strength is about 0.98 MPa. Under triaxial compression, there is a clear transition from volumetric compressibility to dilatancy and a strong dependency on confining pressure. Based on the experimental evidence, an elastoplastic model is proposed using a linear yield function and a nonassociated plastic potential. There is good agreement between numerical results and experimental data.

  5. Monitoring hydrate formation and dissociation in sandstone and bulk with magnetic resonance imaging.

    Science.gov (United States)

    Baldwin, B A; Moradi-Araghi, A; Stevens, J C

    2003-11-01

    Magnetic resonance imaging (MRI) has been shown to be a very effective tool for monitoring the formation and dissociation of hydrates because of the large intensity contrast between the images of the liquid components and the solid hydrate. Tetrahydrofuran/water hydrate was used because the two liquid components are miscible and form hydrate at ambient pressure. These properties made this feasibility study proceed much faster than using methane/water, which requires high pressure to form the hydrate. The formation and dissociation was monitored first in a THF/water-saturated Berea sandstone plug and second in the bulk. In both cases it appeared that nucleation was needed to begin the formation process, i.e., the presence of surfaces in the sandstone and shaking of the bulk solution. Dissociation appeared to be dominated by the rate of thermal energy transfer. The dissociation temperature of hydrate formed in the sandstone plug was not significantly different from the dissociation temperature in bulk.

  6. Frictional behaviour of sandstone: A sample-size dependent triaxial investigation

    Science.gov (United States)

    Roshan, Hamid; Masoumi, Hossein; Regenauer-Lieb, Klaus

    2017-01-01

    Frictional behaviour of rocks from the initial stage of loading to final shear displacement along the formed shear plane has been widely investigated in the past. However the effect of sample size on such frictional behaviour has not attracted much attention. This is mainly related to the limitations in rock testing facilities as well as the complex mechanisms involved in sample-size dependent frictional behaviour of rocks. In this study, a suite of advanced triaxial experiments was performed on Gosford sandstone samples at different sizes and confining pressures. The post-peak response of the rock along the formed shear plane has been captured for the analysis with particular interest in sample-size dependency. Several important phenomena have been observed from the results of this study: a) the rate of transition from brittleness to ductility in rock is sample-size dependent where the relatively smaller samples showed faster transition toward ductility at any confining pressure; b) the sample size influences the angle of formed shear band and c) the friction coefficient of the formed shear plane is sample-size dependent where the relatively smaller sample exhibits lower friction coefficient compared to larger samples. We interpret our results in terms of a thermodynamics approach in which the frictional properties for finite deformation are viewed as encompassing a multitude of ephemeral slipping surfaces prior to the formation of the through going fracture. The final fracture itself is seen as a result of the self-organisation of a sufficiently large ensemble of micro-slip surfaces and therefore consistent in terms of the theory of thermodynamics. This assumption vindicates the use of classical rock mechanics experiments to constrain failure of pressure sensitive rocks and the future imaging of these micro-slips opens an exciting path for research in rock failure mechanisms.

  7. Complete-member Ethnography

    Directory of Open Access Journals (Sweden)

    Hsun-Yu Sharon Chuang

    2015-11-01

    Full Text Available Within the vast array of ethnographic research methodology, complete-member ethnography (CME is one ethnographic inquiry whose methodological development is still in infantile in intercultural communication research. Specifically in this article, the author includes four major sections to understand and to advance CME. First, the author reviews the historical development of CME, and realizes epistemological intimacy as the core of CME and as how researchers’ complete-memberships may be established. Second, the author explains the concept and practice of epistemological intimacy in extant literature. Third, the author advances the concept of epistemological intimacy to identify and explain five contextual factors that influence a complete-member ethnographer’s complete-membership to his or her research community. The five factors include historicity of identity, institutional memory, situational (intersubjectivity, consensual membership, and symbolic codes. In order to elucidate that said factors are essentially interrelated, the author supplements the five factors with her conceptualizations of selfhood/identity. In the end, the author discusses three potential contributions of how CME can advance critical communication research, which pertain to (a praxis and reflexivity, (b challenging struggles and inequalities in power and privilege, and (c promote hopeful social justice from within.

  8. CO2-Driven Convection Produced the Vertical Distribution of Sandstone Colors and Iron Concretions in Navajo Sandstone at Zion National Park, Utah (USA)

    Science.gov (United States)

    Kettler, R. M.; Loope, D. B.

    2011-12-01

    Along cliff faces exposed in Zion National Park (SW Utah), the porous and permeable Navajo Sandstone (Jurassic) is 700 m thick, and is capped by impermeable mudrocks and evaporites of the Carmel Formation. Previous workers have documented an areally extensive color pattern that is easily visible across much of southwestern and south-central Utah: the uppermost Navajo Sandstone is nearly white, the middle third of the formation is pink, and the lowermost fraction is reddish brown. To the northwest of the park, however, the formation is uniformly red (likely its primary color; G.B. Nielsen et al., 2009). Spheroidal concretions with dense, iron-oxide-cemented rinds and iron-poor cores are abundant in the pink and brown sandstones. Rhomb-shaped clots of iron oxide cement that are pseudomorphous after siderite are present in the cores of the largest concretions. The color variations are evidence that iron was transported from the upper portion of the Navajo SS to the lower portion. The pseudomorphs are evidence that the concretions are the oxidized remains of siderite-cemented precursors. The vertical iron transport and the precipitation of siderite require similar vertical transport of reducing, CO2-rich formation waters through the Navajo Sandstone. We argue that this circulation was driven in part by groundwater convection beneath a CO2 accumulation that was trapped below the Navajo-Carmel contact. This circulation caused aqueous iron and aqueous carbonate to be displaced downward and to accumulate (in the form of siderite) in the lower Navajo Sandstone. There are numerous CO2 reservoirs in the Colorado Plateau region; the gas was derived mainly from mantle sources. We hypothesize that, in the late Tertiary, the Carmel Formation capped a broad, structurally high accumulation of CO2 and CH4 in the Navajo Sandstone. The CH4 bleached the upper portion of the sandstone, releasing Fe2+ into the formation water. CO2 dissolved in the water, thereby increasing its density

  9. Submarine-fan facies associations of the Eocene Butano Sandstone, Santa Cruz mountains, California

    Science.gov (United States)

    Nilsen, Tor H.

    1984-06-01

    The Eocene Butano Sandstone was deposited as a submarine fan in a relatively small, partly restricted basin in a borderland setting. It is possibly as thick as 3000 m and was derived from erosion of nearly Mesozoic granitic and older metamorphic rocks located to the south. Deposition was at lower bathyal to abyssal water depths. The original fan may have been 120-to 160-km long and 80-km wide. Outcrops of submarine-canyon, innerfan, middle-fan, and outer-fan facies associations indicate that the depositional model of Mutti and Ricci Lucchi can be used to describe the Butano Sandstone.

  10. The effects of impure CO2 on reservoir sandstones: results from mineralogical and geomechanical experiments

    Science.gov (United States)

    Marbler, H.; Erickson, K. P.; Schmidt, M.; Lempp, Ch.; Pöllmann, H.

    2012-04-01

    An experimental study of the behaviour of reservoir sandstones from deep saline aquifers during the injection and geological storage of CO2 with the inherent impurities SOX and NOX is part of the German national project COORAL*. Sample materials were taken from outcrops of possible reservoir formations of Rotliegend and Bunter Sandstones from the North German Basin. A combination of mineralogical alteration experiments and geomechanical tests was carried out on these rocks to study the potential effects of the impurities within the CO2 pore fluid. Altered rock samples after the treatment with CO2 + SOX/NOX in an autoclave system were loaded in a triaxial cell under in-situ pressure and temperature conditions in order to estimate the modifications of the geomechanical rock properties. Mineralogical alterations were observed within the sandstones after the exposure to impure supercritical (sc)CO2 and brine, mainly of the carbonatic, but also of the silicatic cements, as well as of single minerals. Besides the partial solution effects also secondary carbonate and minor silicate mineral precipitates were observed within the pore space of the treated sandstones. These alterations affect the grain structure of the reservoir rock. Results of geomechanical experiments with unaltered sandstones show that the rock strength is influenced by the degree of rock saturation before the experiment and the chemical composition of the pore fluid (scCO2 + SOX + NOX). After long-term autoclave treatment with impure scCO2, the sandstone samples exhibit modified strength parameters and elastic deformation behaviour as well as changes in porosity compared to untreated samples. Furthermore, the injected fluid volume into the pore space of sandstones from the same lithotype varies during triaxial loading depending on the chemistry of the pore fluid. CO2 with NOX and SOX bearing fluid fills a significantly larger proportion of the sandstone pore space than brine with pure scCO2. * The

  11. Quantifying the effect of squirt flow dispersion from compliant clay porosity in clay bearing sandstones

    DEFF Research Database (Denmark)

    Sørensen, Morten Kanne; Fabricius, Ida Lykke

    2013-01-01

    Compliant porosity in the form of cracks is known to cause significant attenuation and velocity dispersion through pore pressure gradients and consequent relaxation, dubbed squirt flow. Squirt flow from cracks vanish at high confining stress due to crack closing. Studies on clay bearing sandstones......-squirt flow on the bulk modulus of a clay bearing sandstone. The predicted magnitude of the clay-squirt effect on the bulk modulus is compared with experimental data. The clay-squirt effect is found to possibly account for a significant portion of the deviances from Gassmann fluid substitution in claybearing...

  12. INFRARED THERMAL IMAGE STUDY ON THE FOREWARNING OF COAL AND SANDSTONE FAILURE UNDER LOAD

    Institute of Scientific and Technical Information of China (English)

    吴立新; 王金庄

    1997-01-01

    In the experimental study, AGE-782 thermal instrument was used to detect the infrared radiation variation of coal and sandstone (wave-length range 3.6~5.5 μm was used). It's discovered that coal and sandstone failure under load have three kinds of infrared thermal features as well as infrared forewarning messages. That are: (1) temperature rises gradually but drops before failure ; (2) temperature rises gradually but quickly rises before failure; (3) first rises,then drops and lower temperature emerges before failure. The further researches and the prospect of micro-wave remote sensing detection .on ground pressure is also discussed.

  13. Biologically-initiated rock crust on sandstone: Mechanical and hydraulic properties and resistance to erosion

    Science.gov (United States)

    Slavík, Martin; Bruthans, Jiří; Filippi, Michal; Schweigstillová, Jana; Falteisek, Lukáš; Řihošek, Jaroslav

    2017-02-01

    Biocolonization on sandstone surfaces is known to play an important role in rock disintegration, yet it sometimes also aids in the protection of the underlying materials from rapid erosion. There have been few studies comparing the mechanical and/or hydraulic properties of the BIRC (Biologically-Initiated Rock Crust) with its subsurface. As a result, the overall effects of the BIRC are not yet well understood. The objective of the present study was to briefly characterize the BIRC from both the mineralogical and biological points of view, and especially to quantify the effect of the BIRC upon the mechanical and hydraulic properties of friable sandstone. The mineralogical investigation of a well-developed BIRC showed that its surface is enriched in kaolinite and clay- to silt-sized quartz particles. Total organic carbon increases with the age of the BIRC. Based on DNA sequencing and microscopy, the BIRC is formed by various fungi, including components of lichens and green algae. Using the method of drilling resistance, by measuring tensile strength, and based on water jet testing, it was determined that a BIRC is up to 12 times less erodible and has 3-35 times higher tensile strength than the subsurface friable sandstone. Saturated hydraulic conductivity of the studied BIRC is 15-300 times lower than the subsurface, and was measured to also decrease in capillary water absorption (2-33 times). Water-vapor diffusion is not significantly influenced by the presence of the BIRC. The BIRC thus forms a hardened surface which protects the underlying material from rain and flowing water erosion, and considerably modifies the sandstone's hydraulic properties. Exposing the material to calcination (550 °C), and experiments with the enzyme zymolyase indicated that a major contribution to the surface hardening is provided by organic matter. In firmer sandstones, the BIRC may still considerably decrease the rate of weathering, as it is capable of providing cohesion to strongly

  14. The making of a sandstone colossus: Tectonically and climatically induced flushing of 'Nubian' sands in the Early Paleozoic

    Science.gov (United States)

    Luthi, Stefan M.; Hagadorn, James W.; Donselaar, Marinus E.

    2013-04-01

    Massive 'Nubian' sandstones of Cambro-Ordovician age drape most of the Arabian and northern African tectonic plates and preserve a sensitive record of how continental margins evolve under greenhouse conditions. These strata also contain important aquifers, petroleum reservoirs, and archaeological monuments such as Petra, and they were formed by a geologically sudden and long-lasting influx of >500,000 km3 of predominantly quartz sand. The cause and timing of this continent-scale sedimentation event were so far unknown. Here we constrain the depositional history of these strata and hypothesize that poleward migration of the Gondwanan supercontinent out of the horse latitudes caused a five-fold increase in sedimentation rates and buildup of one of the largest epicratonic sand wedges in earth history. Geohistorical sedimentation and subsidence modeling of these sandstones is presented, based on sedimentologic, biostratigraphic, basement paleotopographic, facies, and tectonic dip analyses of a well-preserved paleoslope-axial transect of 542-462 million-year-old strata in Jordan. This region experienced a ~25 m/Ma increase in sedimentation rate over ~30 Ma, concomitant with near-equilibrium plate subsidence response. Sedimentary rocks in the studied sequences exhibit coeval compositional variations that suggest a change in sedimentation style from immature to ultramature clastics. Our results are internally consistent with movement of a continent from an arid subtropical high toward a wet subpolar low, which would have caused widespread flushing of hypermature sands sourced from the interior of the African-Nubian Shield toward the continent margin.

  15. Laser Ablation Split Stream (LASS) U-Pb & Lu-Hf Isotope Analysis of Detrital Zircons from the Old Red Sandstone, NW Svalbard: Implications for Northern Caledonian Paleogeography

    Science.gov (United States)

    Beranek, L. P.; Gee, D. G.; Fisher, C. M.

    2015-12-01

    The Svalbard archipelago consists of three Caledonian provinces that were assembled by thrusting and transcurrent faulting during the Silurian and Devonian in a location directly northeast of the Greenland Caledonides. Syn- to post-orogenic alluvial strata, referred to as the Old Red Sandstones, filled pull-apart basins adjacent to the transcurrent faults and comprise cover assemblages that help constrain the timing of the Caledonian orogeny. To further investigate the tectonic history and paleogeography of the Raudfjorden-Liefdefjorden-Woodfjorden area of Spitsbergen, NW Svalbard, we analyzed rock samples of the Old Red Sandstones and underlying Precambrian basement complexes for detrital zircon analysis. Laboratory studies of the Old Red Sandstones include the novel Laser Ablation Split Stream (LASS) technique, which allows for simultaneous U-Pb & Lu-Hf isotope analysis of zircon crystals. Lower Devonian Red Bay Group strata contain a range of early Neoproterozoic to Neoarchean detrital zircons with prominent age peaks c. 960, 1050, 1370, 1450, 1650, and 2700 Ma; subordinate Ordovician (c. 460-490 Ma) and Cryogenian (c. 650 Ma) detrital zircons occur in a subset of the samples. Underlying Precambrian metasedimentary rocks are composed of similar earliest Neoproterozoic to Neoarchean age populations, which argues for much of the Red Bay Group to be derived from local basement rocks during thrusting and other faulting. The U-Pb ages and Hf isotope compositions of Paleozoic to Neoarchean detrital zircons are consistent with Arctic crustal evolution, and support the hypothesis that northwestern and northeastern provinces of the Svalbard Caledonides are extruded fragments of the northeast Greenland allochthons. The new Hf isotope results further allow paleogeographic and stratigraphic comparisons with rock assemblages proximal to the North Atlantic Caledonides during the Silurian-Devonian, including the Pearya terrane of Ellesmere Island, Alexander terrane of NW

  16. Depositional Environments of the Upper Permian Quartzose Sandstone (Shandong Province, North China):Insight from Trace Element Geochemistry

    Institute of Scientific and Technical Information of China (English)

    Dawei L; Zengxue Li; Jitao Chen; Ying Liu; Zengqi Zhang; Jipo Liang; Haiyan Liu

    2015-01-01

    The depositional environment of the Upper Permian quartzose sandstone (Kuishan sand-stone in Shihezi Formation of Upper Permian) in the North China epicontinental basin is controversial. In order to test the previous hypotheses, we analyzed sedimentological characteristics of the Kuishan sandstones in outcrops and boreholes, and carried out trace element geochemical analysis by electron probe microanalyzer. Three lithofacies were recognized, including normal-graded conglomerate (Cng), trough and planar cross-bedded coarse sandstone (CStpc), and planar cross-bedded medium sandstone (MSpc). Normal-graded conglomerate (Cng) formed in the meandering river or deltaic distributary channels. Trough and planar cross-bedded coarse sandstone (CStpc) formed in meandering river or distributary channels of near-source deltaic plain. Planar cross-bedded medium sandstone (MSpc) formed in the siliciclastic beach with high-to moderate-energy conditions. By the petrology and trace elements analysis, three relatively large-scale transgressions were revealed. Each transgression was re-flected by the lower content of Ba and ratios of Fe/Mn, and the high content of B and ratios of B/Ga. The ratios of Ni/Co of all samples are all lower than 2, suggesting oxygen-enriched shallower water en-vironment during deposition of the Kuishan sandstones.

  17. Consistency of trace norm minimization

    CERN Document Server

    Bach, Francis

    2007-01-01

    Regularization by the sum of singular values, also referred to as the trace norm, is a popular technique for estimating low rank rectangular matrices. In this paper, we extend some of the consistency results of the Lasso to provide necessary and sufficient conditions for rank consistency of trace norm minimization with the square loss. We also provide an adaptive version that is rank consistent even when the necessary condition for the non adaptive version is not fulfilled.

  18. High SNR Consistent Compressive Sensing

    OpenAIRE

    Kallummil, Sreejith; Kalyani, Sheetal

    2017-01-01

    High signal to noise ratio (SNR) consistency of model selection criteria in linear regression models has attracted a lot of attention recently. However, most of the existing literature on high SNR consistency deals with model order selection. Further, the limited literature available on the high SNR consistency of subset selection procedures (SSPs) is applicable to linear regression with full rank measurement matrices only. Hence, the performance of SSPs used in underdetermined linear models ...

  19. Offers for our members

    CERN Multimedia

    Staff Association

    2013-01-01

    The warm weather arrives, it's time to take advantage of our offers Walibi and Aquapark! Walibi : Tickets "Zone terrestre": 21 € instead of 26 € Access to Aqualibi: 5 € instead of 8 € on presentation of your SA member ticket. Free for children (3-11 years old) before 12 h 00. Free for children under 3, with limited access to the attractions. Car park free. * * * * * Aquaparc : Half-day ticket (5 hours): – Children: 26 CHF instead of 35 CHF – Adults : 32 CHF instead of 43 CHF Day ticket: – Children: 30 CHF instead of 39 CHF – Adults : 36 CHF instead of 49 CHF Free for children under 5.

  20. Offers for our members

    CERN Multimedia

    Staff Association

    2013-01-01

    The Courir shops propose the following offer: 15% discount on all articles (not on sales) in the Courir shops (Val Thoiry, Annemasse and Neydens) and 5% discount on sales upon presentation of your Staff Association membership card and an identity card before payment. Summer is here, enjoy our offers for the aquatic parcs! Walibi : Tickets "Zone terrestre": 21 € instead of 26 €. Access to Aqualibi: 5 € instead of 8 € on presentation of your SA member ticket. Free for children (3-11 years old) before 12 h 00. Free for children under 3, with limited access to the attractions. Car park free. * * * * * Aquaparc : Day ticket: – Children: 30 CHF instead of 39 CHF – Adults : 36 CHF instead of 49 CHF Bonus! Free for children under 5.

  1. Offers for our members

    CERN Multimedia

    Association du personnel

    2013-01-01

    La banque LCL propose aux membres de l’Association du personnel les avantages suivants : – Un barème Privilège sur le Prêt immobilier – Des avantages tarifaires sur l’épargne, notamment l’assurance-vie. – Un taux préférentiel de prêt à la consommation. En outre, jusqu’au 30 septembre 2013, elle offre 50€ à tous les nouveaux clients, membres de l'Association du personnel. Summer is here, enjoy our offers for the aquatic parcs! Tickets "Zone terrestre" : 21 € instead of de 26 €. Access to Aqualibi : 5 euros instead of 8 euros on presentation of your SA member ticket. Free for children (3-11 years old) before 12 h 00. Free for children under 3, with limited access to the attractions. Free car park. * * * * * * * Full day ticket: – Children : 30 CHF instead of 39 CHF &...

  2. A multi-tracer study in the Hutton Sandstone aquifer, Australia: How "wrong ages" give us deeper insights into aquifer structure and effective deep recharge to a double porosity system

    Science.gov (United States)

    Suckow, Axel; Taylor, Andrew; Davies, Phil; Leaney, Fred

    2017-04-01

    Depressurisation of coal seams in the Walloon Coal Measures in Queensland, Australia, may influence aquifers both over- and underlying the formation. The Gubberamunda Sandstone aquifer, which overlies the Walloon Coal Measures, is the starting point of the Great Artesian Basin (GAB) flow system and has been the focus of numerous recharge studies. In comparison, the Hutton Sandstone aquifer, which underlies the Walloon Coal Measures, has received much less attention. This aquifer however, is the main supply of stock water for the beef industry in the area. A multi-environmental tracer study of the Hutton Sandstone aquifer was undertaken at the Mimosa Syncline and was complemented by a few samples taken from the underlying Precipice Sandstone aquifer. This multi-tracer study (comprising 18O, 2H, 3H, CFCs, SF6, 14C, 36Cl, and 4He) demonstrated that the Hutton Sandstone aquifer behaves as a double porosity system. At the regional scale, the system features a relatively small fraction of conductive rock within a fairly large fraction of low permeability rock. Tracer migration therefore occurs mainly by advection in the conductive fraction and mainly by diffusion in the low-permeability fraction of the aquifer. Groundwater flow velocities, derived from exponential decrease of 14C and 36Cl concentrations with distance, differ by a factor of ten and therefore do not indicate the real groundwater flow velocity. However, accounting for a double porosity interpretation of the tracer data leads to a single groundwater flow velocity that is consistent with all observed data. Advective velocity in this double porosity model differs from face value flow velocities derived from 14C and 36Cl by a factor of 4 and 40 respectively. As a consequence of this interpretation, the deeper groundwater flow system of the Hutton Sandstone aquifer is estimated to receive only 3% of the recharge previously estimated using the Chloride Mass Balance approach at the intake beds. The other 97% is

  3. Mapping of diagenetic processes in sandstones using imaging spectroscopy: A case study of the Utrillas Formation, Burgos, Spain

    Science.gov (United States)

    Alonso de Linaje, Virginia; Khan, Shuhab D.

    2017-05-01

    Imaging spectroscopy is applied to sandstone formation to study diagenetic processes in sedimentary deposits. The study was carried out on the upper member of the Utrillas Formation in Spain. Shortwave infrared and visible near-infrared Specim® hyperspectral cameras were used to scan near-vertical and well-exposed outcrop walls. Reflectance spectra from close-range hyperspectral imaging was compared with high-resolution laboratory spectra, hyperspectral imagining data, thin sections, and results of previous sedimentological studies to analyze geochemical variations and quantify facies and diagenetic mineral abundances. Distinctive characteristics of the absorption features of clay minerals were used to develop a kaolinite crystallinity index to identify detrital kaolinite and authigenic kaolinite in the Utrillas Formation. Results show that poorly ordered kaolinite is only present in floodplain deposits, whereas well-ordered authigenic kaolinite is related to paleochannel deposits and organic-rich irregular patches. Meteoric water flux probably induced feldspar and mica alteration, as well as authigenic clays precipitation. Contemporary microbial degradation of organic matter in the subsurface might be the cause of authigenic clay formation at the alteration areas. This study provides new data and interpretation on diagenetic alterations of the Utrillas Formation. Results of this work may have important implications in the mining industry as a methodology to evaluate mining areas of interest.

  4. Provenance of Permian Malužiná Formation sandstones (Hronicum, Western Carpathians): evidence from monazite geochronology

    Science.gov (United States)

    Vozárová, Anna; Konečný, Patrik; Vďačný, Marek; Vozár, Jozef; Šarinová, Katarína

    2014-10-01

    The Permian Malužiná Formation and the Pennsylvanian Nižná Boca Formation are Upper Paleozoic volcano- sedimentary complexes in the Hronicum nappe system. Sandstones, shales and conglomerates are the dominant lithological members of the Malužiná Formation sequence. Detrital monazites were analysed by electron microprobe, to obtain Th-U-Pb ages of the source areas. The majority of detrital monazites showed Devonian-Mississippian ages, ranging from 330 to 380 Ma with a weighted average of 351 ± 3.3 (2σ), that correspond well with the main phase of arcrelated magmatic activity in the Western Carpathians. Only a small portion of detrital monazites displayed Permian ages in the range of 250-280 Ma, with a significant maximum around 255 Ma. The weighted average corresponds to 255 ± 6.2 Ma. These monazites may have been partially derived from the synsedimentary acid volcanism that was situated on the margins of the original depositional basin. However, some of the Triassic ages (230-240 Ma), reflect, most likely, the genetic relationship with the overheating connected with Permian and subsequent Triassic extensional regime. Detrital monazite ages document the Variscan age of the source area and also reflect a gradual development of the Hronicum terrestrial rift, accompanied by the heterogeneous cooling of the lithosphere.

  5. Provenance of Permian Malužiná Formation sandstones (Hronicum, Western Carpathians: evidence from monazite geochronology

    Directory of Open Access Journals (Sweden)

    Vozárová Anna

    2014-10-01

    Full Text Available The Permian Malužiná Formation and the Pennsylvanian Nižná Boca Formation are Upper Paleozoic volcano- sedimentary complexes in the Hronicum nappe system. Sandstones, shales and conglomerates are the dominant lithological members of the Malužiná Formation sequence. Detrital monazites were analysed by electron microprobe, to obtain Th-U-Pb ages of the source areas. The majority of detrital monazites showed Devonian-Mississippian ages, ranging from 330 to 380 Ma with a weighted average of 351 ± 3.3 (2σ, that correspond well with the main phase of arcrelated magmatic activity in the Western Carpathians. Only a small portion of detrital monazites displayed Permian ages in the range of 250-280 Ma, with a significant maximum around 255 Ma. The weighted average corresponds to 255 ± 6.2 Ma. These monazites may have been partially derived from the synsedimentary acid volcanism that was situated on the margins of the original depositional basin. However, some of the Triassic ages (230-240 Ma, reflect, most likely, the genetic relationship with the overheating connected with Permian and subsequent Triassic extensional regime. Detrital monazite ages document the Variscan age of the source area and also reflect a gradual development of the Hronicum terrestrial rift, accompanied by the heterogeneous cooling of the lithosphere.

  6. A condensed middle Cenomanian succession in the Dakota Sandstone (Upper Cretaceous), Sevilleta National Wildlife Refuge, Socorro County, New Mexico

    Science.gov (United States)

    Hook, Stephen C.; Cobban, William A.

    2007-01-01

    The upper part of the Dakota Sandstone exposed on the Sevilleta National Wildlife Refuge, northern Socorro County, New Mexico, is a condensed, Upper Cretaceous, marine succession spanning the first five middle Cenomanian ammonite zones of the U.S. Western Interior. Farther north in New Mexico these five ammonite zones occur over a stratigraphic interval more than an order of magnitude thicker. The basal part of this marine sequence was deposited in Seboyeta Bay, an elongate east-west embayment into New Mexico that marked the initial transgression of the western shoreline of the Late Cretaceous seaway into New Mexico. The primary mechanism for condensing this section was nearshore, submarine erosion, although nondeposition played a minor role. The ammonite fossils from each zone are generally fragments of internal molds that are corroded on one side, indicating submarine burial, erosion of the prefossilized steinkern, and corrosion on the sea floor. In addition, the base of the condensed succession is marked by a thin bed that contains abundant, white-weathering, spherical to cylindrical phosphate nodules, many of which contain a cylindrical axial cavity of unknown origin. The nodules lie on the bedding surface of the highly burrowed, ridge-forming sandstone near the top of the Dakota and occur in the overlying breccia. The breccia consists of rip-up clasts of sandstone and eroded internal molds of the ammonite Conlinoceras tarrantense, the zonal index for the basal middle Cenomanian. The nodules below the breccia imply a time of erosion followed by nondeposition or sediment bypass during which the phosphatization occurred. The breccia implies a time of submarine erosion, probably storm-related. Remarkably, this condensed succession and the basal part of the overlying Mancos Shale tongue contain one of the most complete middle Cenomanian ammonite sequences in the U.S. Western Interior. Five of the six ammonite zones that characterize the middle Cenomanian of the

  7. Origin and timing of siderite cementation in Upper Ordovician glaciogenic sandstones from the Murzuq basin, SW Libya

    Energy Technology Data Exchange (ETDEWEB)

    El-ghali, M.A.K.; Mansurbeg, H. [Department of Earth Science, Uppsala University, Villavaegen 16, SE 75236 Uppsala (Sweden); Tajori, K.G. [Department of Earth Science, Faculty of Science, Al-Fateh University, P.O. Box 13696, Tripoli (Libya); Ogle, N.; Kalin, R.M. [School of Civil Engineering, Environmental Engineering Research Centre, The Queen' s University of Belfast, Stranmillis Road, Belfast BT9 5AG (United Kingdom)

    2006-05-15

    The origin and timing of siderite cementation have been constrained in relation to depositional facies and sequence stratigraphy of Upper Ordovician glaciogenic sandstones from the Murzuq basin, SW Libya. Optical microscope, backscattered electron imagery, and carbon and oxygen stable isotope analysis have revealed that siderite is of eo- and mesogenetic origin. Eogenetic siderite is Mg-poor with a mean composition of (Fe{sub 91.7}Mg{sub 1.5}Ca{sub 0.3}Mn{sub 6.5})CO{sub 3}, and occurs in paraglacial, tide-dominated deltaic highstand systems tract (HST) sandstones, in paraglacial, foreshore to shoreface HST sandstones and in postglacial, Gilbert-type deltaic lowstand systems tract (LST) sandstones. This siderite is typically of meteoric water origin that influxed into the LST and HST sandstones during relative sea level fall and basinward shift of the strandline. Mesogenetic siderite, which engulfs and thus postdates quartz overgrowths and illite, is Mg-rich with a mean composition of (Fe{sub 72.2}Mg{sub 21.7}Ca{sub 0.8}Mn{sub 5.3})CO{sub 3} and occurs in the paraglacial, tide-dominated deltaic HST sandstones, in paraglacial foreshore to shoreface HST sandstones, in glacial, tide-dominated estuarine transgressive systems tract (TST) sandstones, in postglacial, Gilbert-type deltaic LST sandstones, and in postglacial, shoreface TST sandstones. {delta}{sup 18}O{sub V-PDB} values of this siderite, which range between -22.6 and -13.8%%, suggest that precipitation has occurred from evolved formation waters with {delta}{sup 18}O values between -14.0 and +1.0%% and was either meteoric, mixed marine-meteoric and/or marine in origin by assuming postdating quartz overgrowths and illite temperature between 80 and 130{sup o}C. (author)

  8. What Indicates Competency in Systems Based Practice? An Analysis of Perspective Consistency among Healthcare Team Members

    Science.gov (United States)

    Graham, Mark J.; Naqvi, Zoon; Encandela, John A.; Bylund, Carma L.; Dean, Randa; Calero-Breckheimer, Ayxa; Schmidt, Hilary J.

    2009-01-01

    In many parts of the world the practice of medicine and medical education increasingly focus on providing patient care within context of the larger healthcare system. Our purpose is to solicit perceptions of all professional stakeholders (e.g. nurses) of the system regarding the U.S. ACGME competency Systems Based Practice to uncover the extent to…

  9. Continuity and internal properties of Gulf Coast sandstones and their implications for geopressured energy development. Annual report, November 1, 1980-October 31, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Morton, R.A.; Ewing, T.E.; Tyler, N.

    1982-06-01

    Systematic investigation, classification, and differentiation of the intrinsic properties of genetic sandstone units that typify many geopressured geothermal aquifers and hydrocarbon reservoirs of the Gulf Coast region are provided. The following are included: structural and stratigraphic limits of sandstone reservoirs; characteristics and dimensions of Gulf Coast Sandstones; fault compartment areas; comparison of production and geologic estimates of aquifer volume; geologic setting and reservoir characteristics, wells of opportunity; internal properties of sandstones and implications for geopressured energy development. (MHR)

  10. Prediction of calcite Cement Distribution in Shallow Marine Sandstone Reservoirs using Seismic Data

    Energy Technology Data Exchange (ETDEWEB)

    Bakke, N.E.

    1996-12-31

    This doctoral thesis investigates how calcite cemented layers can be detected by reflection seismic data and how seismic data combined with other methods can be used to predict lateral variation in calcite cementation in shallow marine sandstone reservoirs. Focus is on the geophysical aspects. Sequence stratigraphy and stochastic modelling aspects are only covered superficially. Possible sources of calcite in shallow marine sandstone are grouped into internal and external sources depending on their location relative to the presently cemented rock. Well data and seismic data from the Troll Field in the Norwegian North Sea have been analysed. Tuning amplitudes from stacks of thin calcite cemented layers are analysed. Tuning effects are constructive or destructive interference of pulses resulting from two or more closely spaced reflectors. The zero-offset tuning amplitude is shown to depend on calcite content in the stack and vertical stack size. The relationship is found by regression analysis based on extensive seismic modelling. The results are used to predict calcite distribution in a synthetic and a real data example. It is found that describing calcite cemented beds in shallow marine sandstone reservoirs is not a deterministic problem. Hence seismic inversion and sequence stratigraphy interpretation of well data have been combined in a probabilistic approach to produce models of calcite cemented barriers constrained by a maximum amount of information. It is concluded that seismic data can provide valuable information on distribution of calcite cemented beds in reservoirs where the background sandstones are relatively homogeneous. 63 refs., 78 figs., 10 tabs.

  11. Diversity and complexity of the Araracuara sandstone flora and vegetation in the Colombian Amazon

    NARCIS (Netherlands)

    A.M. Cleef; M.V. Arbelaez Velasquez

    2005-01-01

    Insular open vegetation of the western Guayana Shield in Colombia (c.150-1000 m) surrounded by NW Amazon rain forest (over 3000 mm annual precipitation) has been botanically unexplored until the early 1990¿s. During recent botanical exploration of the sandstone plateaus of the Araracuara region a to

  12. A new biostratigraphical tool for reservoir characterisation and well correlation in permo-carboniferous sandstones

    NARCIS (Netherlands)

    Garming, J.F.L.; Cremer, H.; Verreussel, R.M.C.H.; Guasti, E.; Abbink, O.A.

    2010-01-01

    Permo-Carboniferous sandstones are important reservoir rocks for natural gas in the Southern North Sea basin. This is a mature area which makes tools for reservoir characterization and well to well correlation important for field optimalisation and ongoing exploration activities. Within the Permo-Ca

  13. Combined rock-physical modelling and seismic inversion techniques for characterisation of stacked sandstone reservoir

    NARCIS (Netherlands)

    Justiniano, A.; Jaya, Y.; Diephuis, G.; Veenhof, R.; Pringle, T.

    2015-01-01

    The objective of the study is to characterise the Triassic massive stacked sandstone deposits of the Main Buntsandstein Subgroup at Block Q16 located in the West Netherlands Basin. The characterisation was carried out through combining rock-physics modelling and seismic inversion techniques. The app

  14. Diversity and complexity of the Araracuara sandstone flora and vegetation in the Colombian Amazon

    NARCIS (Netherlands)

    Cleef, A.M.; Arbelaez Velasquez, M.V.; Friis, I.; Balslev, H.

    2005-01-01

    Insular open vegetation of the western Guayana Shield in Colombia (c.150-1000 m) surrounded by NW Amazon rain forest (over 3000 mm annual precipitation) has been botanically unexplored until the early 1990¿s. During recent botanical exploration of the sandstone plateaus of the Araracuara region a

  15. Salt precipitation due to supercritical gas injection: I. Capillary-driven flow in unimodal sandstone

    NARCIS (Netherlands)

    Ott, H.; Roels, S.M.; De Kloe, K.

    2015-01-01

    Drying and salt precipitation in geological formations can have serious consequences for upstream operations in terms of injectivity and productivity. Here we investigate the consequences of supercritical CO2 injection in sandstones. The reported findings are directly relevant for CO2 sequestration

  16. Ferroan dolomite cement in Cambrian sandstones: burial history and hydrocarbon generation of the Baltic sedimentary basin

    DEFF Research Database (Denmark)

    Sliaupa, S.; Cyziene, J.; Molenaar, Nicolaas

    2008-01-01

    The conditions and timing of carbonate cementation in Cambrian sandstones of the Baltic sedimentary basin were determined by oxygen and carbon stable isotope and chemical data in combination with optical and cathodoluminescence petrographic studies. Studied samples represent a range in present...

  17. A transfer learning method for automatic identification of sandstone microscopic images

    Science.gov (United States)

    Li, Na; Hao, Huizhen; Gu, Qing; Wang, Danru; Hu, Xiumian

    2017-06-01

    Classification of sandstone microscopic images is an essential task in geology, and the classical method is either subjective or time-consuming. Computer aided automatic classification has been proved useful, but it seldom considers the situation where sandstone images are collected from separated regions. In this paper, we provide a method called Festra, which uses transfer learning to handle the problem of interregional sandstone microscopic image classification. The method contains two parts: one is feature selection, which aims to screen out features having great difference between the regions, the other is instance transfer using an enhanced TrAdaBoost, whose object is to mitigate the difference among thin section images collected from the regions. Experiments are conducted based on the sandstone images taken from four regions in Tibet to study the performance of Festra. The experimental results have proved both effectiveness and validity of Festra, which provides competitive prediction performance on all the four regions, with few target instances labeled suitable for the field use.

  18. Performance Comparison of New Combinations of Acids with Mud Acid in Sandstone Acidizing

    Directory of Open Access Journals (Sweden)

    Mian Umer Shafiq

    2014-01-01

    Full Text Available The aim of this research is to find the best suitable acid to acidize undamaged low permeable sandstone formation Stimulation of sandstone formations is a challenging task, which involves several chemicals and physical interactions of the acid with the formation. Mud acid has been successfully used to stimulate sandstone reservoirs for a number of years. Matrix acidizing may also be used to increase formation permeability in undamaged wells. The change may be up to 50 to 100% with the mud acid. For any acidizing process, the selection of acid (Formulation and Concentration and the design (Pre-flush, Main Acid, After-flush is very important. Different researchers are using different combinations of acids with different concentrations to get the best results for acidization. Mainly the common practice is combination of Hydrochloric Acid- Hydrofluoric with Concentration (3% HF-12% HCl. This study presents the results of a laboratory investigation of Orthophosphoric acid instead of hydrochloric acid in one combination and the second combination is Fluoboric and formic acid and the third one is formic and hydrofluoric acid. The results are compared with the mud acid and the results analyzed are porosity, permeability, strength, color change and FESEM Analysis. All of these new combinations shows that these have the potential to be used as acidizing acids on sandstone formations.

  19. Fluid Flow History in Lower Triassic Bulgo Sandstone, Central Sydney Basin, Australia

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The fluid flow history during diagenesis of the Lower Triassic Bulgo sandstone has been investigated through integrated analyses of petrography, stable isotope and fluid inclusion. Combined application of these techniques was intended to constrain the temperature, timing, chemistry and source of pore fluids during diagenetic cementation events in the Lower Triassic Bulgo sandstone. The dlagenesis proceeded in two different flow regimes: early dynamic fluid flow regime and late slow static fluid flow regime. The former was characterized by a slight increase of δ(18O) of pore waters form estimated -15 × 10-3 to -14 × 10-3 with the temperature increasing from ~ 10 ℃ to ~ 75 ℃. During early diagenesis, early clays and pore filling carbonates precipitated from the pore waters. The late slow flow/static fluid regime was characterized by a rapid 18O-enrichment process. δ(18O) of pore waters increased from -14× 10-3 to -5× 10-3 with the temperature increasing from 75 ℃ to 110 ℃. During the late diagenesis, kaolin (generation Ⅲ ), quartz and illite crystallized. Oil migrated to the sandstones of the Bulgo sandstone during quartz cementation.

  20. Diagenesis and Its Effect on Reservoir Quality of Silurian Sandstones, Tabei Area, Tarim Basin, China

    Institute of Scientific and Technical Information of China (English)

    Zhang Jinliang; Jia Ying; Du Guilin

    2007-01-01

    The diagenetic processes of the Tabei sandstones in the Tarim Basin include compaction, cementation (quartz overgrowths, calcite, clay minerals and a minor amount of pyrite), and dissolution of the feldspar and calcite cement.Porosity was reduced by compaction from an assumed original 40% to about 22.1%. Cementation reduced porosity to 26.6%. The Tabei sandstones lost a little more porosity by compaction than by cementation. Quartz cementation,especially syntaxial quartz overgrowth, is a major cause of porosity-loss in many reservoirs in moderately to deeply buried sandstone. Calcite cementation played a key role in the porosity evolution of sandstones. At the early stage of burial, the early calcite cement occupied most of the pore spaces resulting in significant porosity. On the other hand, some primary porosity has been preserved due to incomplete filling or the presence of scattered patches of calcite cement. In addition to calcite, several clay minerals, including illite and chlorite occurred as pore-filling and pore-lining cements.The pore-lining chlorite may have helped in retaining the porosity by preventing the precipitation of syntaxial quartz overgrowths. Illite, which largely occurred as hair-like rims around the grains and bridges on the pore throats, caused a substantial deterioration of penetrability of the reservoir. Calcite cement dissolution was extensive and contributed significantly to the development of secondary porosity.

  1. Thermal-mechanical coupled effect on fracture mechanism and plastic characteristics of sandstone

    Institute of Scientific and Technical Information of China (English)

    ZUO; JianPing; XIE; HePing; ZHOU; HongWei; PENG; SuPing

    2007-01-01

    Scanning electronic microscopy (SEM) was employed to investigate fractographs of sandstone in mine roof strata under thermal-mechanical coupled effect. Based on the evolution of sandstone surface morphology in the failure process and fractography, the fracture mechanism was studied and classified under meso and micro scales, respectively. The differences between fractographs under different temperatures were examined in detail. Under high temperature, fatigue fracture and plastic deformation occurred in the fracture surface. Therefore, the temperature was manifested by these phenomena to influence strongly on micro failure mechanism of sandstone. In addition, the failure mechanism would transit from brittle failure mechanism at low temperature to coupled brittle-ductile failure mechanism at high temperature. The variation of sandstone strength under different temperature can be attributed to the occurrence of plastic deformation, fatigue fracture, and microcracking. The fatigue striations in the fracture surfaces under high temperature may be interpreted as micro fold. And the coupled effect of temperature and tensile stress may be another formation mechanism of micro fold in geology.

  2. Combined rock-physical modelling and seismic inversion techniques for characterisation of stacked sandstone reservoir

    NARCIS (Netherlands)

    Justiniano, A.; Jaya, Y.; Diephuis, G.; Veenhof, R.; Pringle, T.

    2015-01-01

    The objective of the study is to characterise the Triassic massive stacked sandstone deposits of the Main Buntsandstein Subgroup at Block Q16 located in the West Netherlands Basin. The characterisation was carried out through combining rock-physics modelling and seismic inversion techniques. The app

  3. Reservoir heterogeneity in Carter Sandstone, North Blowhorn Creek oil unit and vicinity, Black Warrior Basin, Alabama

    Energy Technology Data Exchange (ETDEWEB)

    Kugler, R.L.; Pashin, J.C.

    1992-05-01

    This report presents accomplishments made in completing Task 3 of this project which involves development of criteria for recognizing reservoir heterogeneity in the Black Warrior basin. The report focuses on characterization of the Upper Mississippian Carter sandstone reservoir in North Blowhorn Creek and adjacent oil units in Lamar County, Alabama. This oil unit has produced more than 60 percent of total oil extracted from the Black Warrior basin of Alabama. The Carter sandstone in North Blowhorn Creek oil unit is typical of the most productive Carter oil reservoirs in the Black Warrior basin of Alabama. The first part of the report synthesizes data derived from geophysical well logs and cores from North Blowhorn Creek oil unit to develop a depositional model for the Carter sandstone reservoir. The second part of the report describes the detrital and diagenetic character of Carter sandstone utilizing data from petrographic and scanning electron microscopes and the electron microprobe. The third part synthesizes porosity and pore-throat-size-distribution data determined by high-pressure mercury porosimetry and commercial core analyses with results of the sedimentologic and petrographic studies. The final section of the report discusses reservoir heterogeneity within the context of the five-fold classification of Moore and Kugler (1990).

  4. Assessment of undiscovered sandstone-hosted uranium resources in the Texas Coastal Plain, 2015

    Science.gov (United States)

    Mihalasky, Mark J.; Hall, Susan M.; Hammarstrom, Jane M.; Tureck, Kathleen R.; Hannon, Mark T.; Breit, George N.; Zielinski, Robert A.; Elliott, Brent

    2015-12-02

    The U.S. Geological Survey estimated a mean of 220 million pounds of recoverable uranium oxide (U3O8 ) remaining as potential undiscovered resources in southern Texas. This estimate used a geology-based assessment method for Tertiary sandstone-hosted uranium deposits in the Texas Coastal Plain sedimentary strata (fig.1).

  5. Architecture of an Upper Jurassic barrier island sandstone reservoir, Danish Central Graben:

    DEFF Research Database (Denmark)

    Johannessen, Peter N.; Nielsen, Lars H.; Nielsen, Lars

    2010-01-01

    An unusually thick (c. 88 m), transgressive barrier island and shoreface sandstone succession characterizes the Upper Jurassic Heno Formation reservoir of the Freja oil field situated on the boundary of Denmark and Norway. The development and preservation of such thick transgressive barrier islan...... such that the island aggraded and even prograded seawards and became wider and longer due to the large surplus of sand....

  6. Determining Upper Bounds for the Clay-squirt Effect in Clay Bearing Sandstone

    DEFF Research Database (Denmark)

    Sørensen, Morten Kanne; Fabricius, Ida Lykke

    Sonic measurements of saturated bulk moduli of clay bearing sandstones show larger values than expected by Gassmann modelling from dry rock properties. This causes difficulties in extrapolation of laboratory data to different saturants or frequencies. Squirt flow from the clay phase of the rock...

  7. Assessment of tight-gas resources in Canyon sandstones of the Val Verde Basin, Texas, 2016

    Science.gov (United States)

    Schenk, Christopher J.; Tennyson, Marilyn E.; Klett, Timothy R.; Mercier, Tracey J.; Brownfield, Michael E.; Gaswirth, Stephanie B.; Hawkins, Sarah J.; Leathers-Miller, Heidi M.; Marra, Kristen R.; Finn, Thomas M.; Pitman, Janet K.

    2016-07-08

    Using a geology-based assessment methodology, the U.S. Geological Survey assessed mean resources of 5 trillion cubic feet of gas and 187 million barrels of natural gas liquids in tight-gas assessment units in the Canyon sandstones of the Val Verde Basin, Texas.

  8. SHORT COMMUNICATION: Sparsely encrusted hardground in the Darriwilian calcareous sandstone of Cape Pakri, NW Estonia (Baltica

    Directory of Open Access Journals (Sweden)

    Olev Vinn

    2015-08-01

    Full Text Available The occurrence of echinoderm and ptilodictyid bryozoan holdfasts on the surface of Darriwilian calcareous sandstone in northwestern Estonia indicates that it was lithified before encrustation. Pelmatozoans outnumber the bryozoans and cover a larger area of the hardground although both are very sparse. The hardground is very sparsely encrusted (0.37% of the total area studied and lacks signs of bioerosion.

  9. Borehole Breakouts Induced in Arkosic Sandstones and a Discrete Element Analysis

    Science.gov (United States)

    Lee, H.; Moon, T.; Haimson, B. C.

    2016-04-01

    A series of laboratory drilling experiments were conducted on two arkosic sandstones (Tenino and Tablerock) under polyaxial far-field stress conditions (σ h ≠ σ H ≠ σ v ). V-shaped breakouts, aligned with the σ h direction and revealing stress-dependent dimensions (width and length), were observed in the sandstones. The microscale damage pattern leading to the breakouts, however, is different between the two, which is attributed to the difference in their cementation. The dominant micromechanism in Tenino sandstone is intergranular microcracking occurring in clay minerals filling the spaces between clastic grains. On the other hand, intra- and transgranular microcracking taking place in the grain itself prevails in Tablerock sandstone. To capture the grain-scale damage and reproduce the failure localization observed around the borehole in the laboratory, we used a discrete element (DE) model in which a grain breakage algorithm was implemented. The microparameters needed in the numerical model were calibrated by running material tests and comparing the macroscopic responses of the model to the ones measured in the laboratory. It is shown that DE modeling is capable of simulating the microscale damage of the rock and replicating the localized damage zone observed in the laboratory. In addition, the numerically induced breakout width is determined at a very early stage of the damage localization and is not altered for the rest of the failure process.

  10. Middle Ordovician brachiopods from the Stairway Sandstone, Amadeus Basin, central Australia

    DEFF Research Database (Denmark)

    Jakobsen, Kristian Grube; Brock, Glenn A.; Nielsen, Arne Thorshøj

    2014-01-01

    Middle Ordovician brachiopod faunas from the Amadeus Basin, central Australia are poorly known. The Darriwilian Stairway Sandstone was sampled stratigraphically for macrofossils in order to provide new information on marine benthic diversity in this clastic-dominated, shallow-water palaeoenvironm...

  11. Interaction of Pseudomonas putida ATCC 12633 and Bacteriophage gh-1 in Berea Sandstone Rock.

    Science.gov (United States)

    Chang, P L; Yen, T F

    1985-12-01

    Measurements of the passage of Pseudomonas putida ATCC 12633 and a phage-resistant mutant through Berea sandstone rock were made. When bacteriophage gh-1 was adsorbed within the rock matrix, a reduction in the passage of the susceptible but not the resistant cells through the rock was observed.

  12. Family members' experiences of autopsy

    NARCIS (Netherlands)

    Oppewal, F; Meyboom-de Jong, B

    2001-01-01

    Background. The experiences of family members will teach us how to handle an autopsy, the ultimate quality assessment tool. Objective. The aim of this study was to determine surviving family members' experience of autopsy. Method. Seven GPs were asked to approach surviving family members of autopsie

  13. Family members' experiences of autopsy

    NARCIS (Netherlands)

    Oppewal, F; Meyboom-de Jong, B

    Background. The experiences of family members will teach us how to handle an autopsy, the ultimate quality assessment tool. Objective. The aim of this study was to determine surviving family members' experience of autopsy. Method. Seven GPs were asked to approach surviving family members of

  14. Consistency argued students of fluid

    Science.gov (United States)

    Viyanti; Cari; Suparmi; Winarti; Slamet Budiarti, Indah; Handika, Jeffry; Widyastuti, Fatma

    2017-01-01

    Problem solving for physics concepts through consistency arguments can improve thinking skills of students and it is an important thing in science. The study aims to assess the consistency of the material Fluid student argmentation. The population of this study are College students PGRI Madiun, UIN Sunan Kalijaga Yogyakarta and Lampung University. Samples using cluster random sampling, 145 samples obtained by the number of students. The study used a descriptive survey method. Data obtained through multiple-choice test and interview reasoned. Problem fluid modified from [9] and [1]. The results of the study gained an average consistency argmentation for the right consistency, consistency is wrong, and inconsistent respectively 4.85%; 29.93%; and 65.23%. Data from the study have an impact on the lack of understanding of the fluid material which is ideally in full consistency argued affect the expansion of understanding of the concept. The results of the study as a reference in making improvements in future studies is to obtain a positive change in the consistency of argumentations.

  15. Non-destructive infrared analyses: a method for provenance analyses of sandstones

    Science.gov (United States)

    Bowitz, Jörg; Ehling, Angela

    2008-12-01

    Infrared spectroscopy (IR spectroscopy) is commonly applied in the laboratory for mineral analyses in addition to XRD. Because such technical efforts are time and cost consuming, we present an infrared-based mobile method for non-destructive mineral and provenance analyses of sandstones. IR spectroscopy is based on activating chemical bonds. By irradiating a mineral mixture, special bonds are activated to vibrate depending on the bond energy (resonance vibration). Accordingly, the energy of the IR spectrum will be reduced thereby generating an absorption spectrum. The positions of the absorption maxima within the spectral region indicate the type of the bonds and in many cases identify minerals containing these bonds. The non-destructive reflection spectroscopy operates in the near infrared region (NIR) and can detect all common clay minerals as well as sulfates, hydroxides and carbonates. The spectra produced have been interpreted by computer using digital mineral libraries that have been especially collected for sandstones. The comparison of all results with XRD, RFA and interpretations of thin sections demonstrates impressively the accuracy and reliability of this method. Not only are different minerals detectable, but also differently ordered kaolinites and varieties of illites can be identified by the shape and size of the absorption bands. Especially clay minerals and their varieties in combination with their relative contents form the characteristic spectra of sandstones. Other components such as limonite, hematite and amorphous silica also influence the spectra. Sandstones, similar in colour and texture, often can be identified by their characteristic reflectance spectra. Reference libraries with more than 60 spectra of important German sandstones have been created to enable entirely computerized interpretations and identifications of these dimension stones. The analysis of infrared spectroscopy results is demonstrated with examples of different sandstones

  16. Coordinating user interfaces for consistency

    CERN Document Server

    Nielsen, Jakob

    2001-01-01

    In the years since Jakob Nielsen's classic collection on interface consistency first appeared, much has changed, and much has stayed the same. On the one hand, there's been exponential growth in the opportunities for following or disregarding the principles of interface consistency-more computers, more applications, more users, and of course the vast expanse of the Web. On the other, there are the principles themselves, as persistent and as valuable as ever. In these contributed chapters, you'll find details on many methods for seeking and enforcing consistency, along with bottom-line analys

  17. Consistency of Random Survival Forests.

    Science.gov (United States)

    Ishwaran, Hemant; Kogalur, Udaya B

    2010-07-01

    We prove uniform consistency of Random Survival Forests (RSF), a newly introduced forest ensemble learner for analysis of right-censored survival data. Consistency is proven under general splitting rules, bootstrapping, and random selection of variables-that is, under true implementation of the methodology. Under this setting we show that the forest ensemble survival function converges uniformly to the true population survival function. To prove this result we make one key assumption regarding the feature space: we assume that all variables are factors. Doing so ensures that the feature space has finite cardinality and enables us to exploit counting process theory and the uniform consistency of the Kaplan-Meier survival function.

  18. Long-Term CO2 Exposure Experiments - Geochemical Effects on Brine-Saturated Reservoir Sandstone

    Science.gov (United States)

    Fischer, Sebastian; Zemke, Kornelia; Liebscher, Axel; Wandrey, Maren

    2010-05-01

    The injection of CO2 into deep saline aquifers is the most promising strategy for the reduction of CO2 emissions to the atmosphere via long-term geological storage. The study is part of the CO2SINK project conducted at Ketzin, situated 40 km west of Berlin. There, food grade CO2 has been pumped into the Upper Triassic Stuttgart Formation since June 2008. The main objective of the experimental program is to investigate the effects of long-term CO2 exposure on the physico-chemical properties of the reservoir rock. To achieve this goal, core samples from observation well Ktzi 202 have been saturated with synthetic brine and exposed to CO2 in high quality steel autoclaves at simulated reservoir P-T-conditions of 5.5 MPa and 40 ° C. The synthetic brine had a composition representative of the formation fluid (Förster et al., 2006) of 172.8 g/l NaCl, 8.0 g/l MgCl2×2H2O, 4.8 g/l CaCl2×2H2O and 0.6 g/l KCl. After 15 months, the first set of CO2-exposed samples was removed from the pressure vessels. Thin sections, XRD, SEM as well as EMP data were used to determine the mineralogical features of the reservoir rocks before and after the experiments. Additionally, NMR relaxation and MP was performed to measure poroperm and pore size distribution values of the twin samples. The analyzed samples are fine- to medium grained, moderately well- to well sorted and weakly consolidated sandstones. Quartz and plagioclase are the major components, while K-feldspar, hematite, white & dark mica, chlorite and illite are present in minor and varying amounts. Cements are composed of analcime, dolomite and anhydrite. Some samples show mm- to cm-scale cross-beddings. The laminae comprise lighter, quartz- and feldspar-dominated layers and dark-brownish layers with notably less quartz and feldspars. The results are consistent with those of Blaschke et al. (2008). The plagioclase composition indicates preferred dissolution of the Ca-component and a trend toward albite-rich phases or even pure

  19. Elemental Gains/Losses Associated with Alteration Fractures in an Eolian Sandstone, Gale Crater, Mars

    Science.gov (United States)

    Ming, D. W.; Yen, A. S.; Gellert, R.; Sutter, B.; Berger, J. A.; Thompson, L. M.; Schmidt, M. E.; Morris, R. V.; Treiman, A. H.

    2016-01-01

    The Mars Science Laboratory rover Curiosity has traversed up section through approximately 100 m of sedimentary rocks deposited in fluvial, deltaic, lacustrine, and eolian environments (Bradbury group and overlying Mount Sharp group). The Stimson formation unconformably overlies a lacustrine mudstone at the base of the Mount Sharp group and has been interpreted to be a cross-bedded sandstone of lithified eolian dunes. Unaltered Stimson sandstone has a basaltic composition similar to the average Mars crustal composition, but is more variable and ranges to lower K and higher Al. Fluids passing through alteration "halos" adjacent to fractures have altered the chemistry and mineralogy of the sandstone. Elemental mass gains and losses in the alteration halos were quantified using immobile element concentrations, i.e., Ti (taus). Alteration halos have elemental gains in Si, Ca, S, and P and large losses in Al, Fe, Mn, Mg, Na, K, Ni, and Zn. Mineralogy of the altered Stimson is dominated by Ca-sulfates, Si-rich X-ray amorphous materials along with plagioclase feldspar, magnetite, and pyroxenes. The igneous phases were less abundant in the altered sandstone with a lower pyroxene/plagioclase feldspar. Large elemental losses suggest acidic fluids initially removed these elements (Al mobile under acid conditions). Enrichments in Si, Ca, and S suggest secondary fluids (possibly alkaline) passed through these fractures leaving behind X-ray amorphous Si and Ca-sulfates. The mechanism for the large elemental gains in P is unclear. The geochemistry and mineralogy of the altered sandstone suggests a complicated diagenetic history with multiple episodes of aqueous alteration under a variety of environmental conditions (e.g., acidic, alkaline).

  20. Upper cretaceous to paleocene depositional sequences and sandstone petrography of southwestern Patagonia (Argentina and Chile)

    Science.gov (United States)

    Macellari, C. E.; Barrio, C. A.; Manassero, M. J.

    Upper Cretaceous to Paleocene strata exposed along the Andean margin of Patagonia south of 50°S were deposited in a foreland basin and comprise a complex transition from continental to marine facies. Three unconformity-bounded sequences are observed within the sedimentary succession studied. Sequence 1 (upper Campanian) displays a rapid north-to-south transition from upper delta plain mudstones (Cerro Fortaleza Formation) through lower delta plain and subaqueous delta plain sandstones (La Anita Formation) to delta-slope and basinal turbidites (Alta Vista and Tres Pasos Formations). Sequence 2 (Maastrichtian-Paleocene) was initiated with braided river sediments (La Irene Formation), deposited over a Type II unconformity ( sensu Vail et al., 1984). These rocks are overlain by meandering fluvial sandstones and mudstones (Chorrillo Formation) that interfinger to the south with fossiliferous shallow marine sandstones (upper Cerro Cazador Formation). Sequence 3 (Paleocene) is composed of shallow marine conglomerates and crossbedded sandstones (Calafate and Cerro Dorotea Formations). These rocks are separated by an angular unconformity from subjacent units. Sandstone petrographic analysis indicates the presence of two main petrofacies within the rocks studied. A quartz-rich petrofacies, present to the north of the basin during late Campanian to early Maastrichtian time, was derived from continental crustal block and recycled orogen sources that were possibly exposed to the northwest of the basin. The second petrofacies (volcanic-rich petrofacies) was restricted to the south of the basin during the late Campanian to early Maastrichtian, but covered the entire area during the late Maastrichtian and Paleocene. These sediments were derived from a dissected magmatic arc located to the west of the study area. The presence of abundant tuffaceous intercalations, as well as fresh andesitic fragments, indicates contemporaneous volcanism near the Cretaceous/Tertiary boundary. The

  1. Sandstone geomorphology of the Golden Gate Highlands National Park, South Africa, in a global context

    Directory of Open Access Journals (Sweden)

    Stefan W. Grab

    2011-03-01

    Full Text Available The Golden Gate Highlands National Park (GGHNP is well known for its impressive sandstone formations. While previous geoscience research in the park has focused on geology, palaeontology, slope forms and the prominent lichen weathering, remarkably little has been written on the diversity and possible origins of sandstone phenomena in the region. The objectives of this study were (1 to present a geomorphological map of prominent and interesting landforms for particular portions of the park and (2 to document the variety of macro- and microscale sandstone formations observed. During field work, we undertook global positioning system measurements to map landforms and, in addition, measured the dimensions of several landform types. A Schmidt hammer was used to conduct rock hardness tests at a variety of localities and lithologies for comparative purposes. We indentified and mapped 27 macro- and microscale sandstone landforms, of which 17 are described in detail. It is demonstrated that for the most part, the landforms are a likely product of surface lithological reactions to a regional climate characterised by pronounced multitemporal temperature and moisture shifts, recently and in the past. However, many of the geomorphological processes producing landforms are controlled by microclimates set up by factors such as macro- and microtopography. Conservation implications: The GGHNP is best known for its geological, geomorphological and palaeontological heritage. This paper highlights the diversity of sandstone geomorphological phenomena, many of them rare and ‘unique’ to the region. Not only are these landforms of aesthetic interest to tourists, but they also provide microhabitats for biota. Thus, conservation of biota requires associated conservation of geo-environments where they are established.

  2. Proposed moduli of dry rock and their application to predicting elastic velocities of sandstones

    Science.gov (United States)

    Lee, Myung W.

    2005-01-01

    Velocities of water-saturated isotropic sandstones under low frequency can be modeled using the Biot-Gassmann theory if the moduli of dry rocks are known. On the basis of effective medium theory by Kuster and Toksoz, bulk and shear moduli of dry sandstone are proposed. These moduli are related to each other through a consolidation parameter and provide a new way to calculate elastic velocities. Because this parameter depends on differential pressure and the degree of consolidation, the proposed moduli can be used to calculate elastic velocities of sedimentary rocks under different in-place conditions by varying the consolidation parameter. This theory predicts that the ratio of P-wave to S-wave velocity (Vp/Vs) of a dry rock decreases as differential pressure increases and porosity decreases. This pattern of behavior is similar to that of water-saturated sedimentary rocks. If microcracks are present in sandstones, the velocity ratio usually increases as differential pressure increases. This implies that this theory is optimal for sandstones having intergranular porosities. Even though the accurate behavior of the consolidation parameter with respect to differential pressure or the degree of consolidation is not known, this theory presents a new way to predict S-wave velocity from P-wave velocity and porosity and to calculate elastic velocities of gas-hydrate-bearing sediments. For given properties of sandstones such as bulk and shear moduli of matrix, only the consolidation parameter affects velocities, and this parameter can be estimated directly from the measurements; thus, the prediction of S-wave velocity is accurate, reflecting in-place conditions.

  3. Elemental Gains/Losses Associated with Alteration Fractures in an Eolian Sandstone, Gale Crater, Mars

    Science.gov (United States)

    Ming, D. W.; Yen, A. S.; Gellert, R.; Sutter, B.; Berger, J. A.; Thompson, L. M.; Schmidt, M. E.; Morris, R. V.; Treiman, A. H.

    2016-12-01

    The Mars Science Laboratory rover Curiosity has traversed up section through 100 m of sedimentary rocks deposited in fluvial, deltaic, lacustrine, and eolian environments (Bradbury group and overlying Mount Sharp group). The Stimson formation unconformably overlies a lacustrine mudstone at the base of the Mount Sharp group and has been interpreted to be a cross-bedded sandstone of lithified eolian dunes. Unaltered Stimson sandstone has a basaltic composition similar to the average Mars crustal composition, but is more variable and ranges to lower K and higher Al. Fluids passing through alteration "halos" adjacent to fractures have altered the chemistry and mineralogy of the sandstone. Elemental mass gains and losses in the alteration halos were quantified using immobile element concentrations, i.e., Ti (taus). Alteration halos have elemental gains in Si, Ca, S, and P and large losses in Al, Fe, Mn, Mg, Na, K, Ni, and Zn. Mineralogy of the altered Stimson is dominated by Ca-sulfates, Si-rich X-ray amorphous materials along with plagioclase feldspar, magnetite, and pyroxenes. The igneous phases were less abundant in the altered sandstone with a lower pyroxene/plagioclase feldspar. Large elemental losses suggest acidic fluids initially removed these elements (Al mobile under acid conditions). Enrichments in Si, Ca, and S suggest secondary fluids (possibly alkaline) passed through these fractures leaving behind X-ray amorphous Si and Ca-sulfates. The mechanism for the large elemental gains in P is unclear. The geochemistry and mineralogy of the altered sandstone suggests a complicated diagenetic history with multiple episodes of aqueous alteration under a variety of environmental conditions (e.g., acidic, alkaline).

  4. Porosities and permeability of Paleozoic sandstones derived from Nuclear Magnetic Resonance measurements

    Science.gov (United States)

    Jorand, Rachel; Koch, Andreas; Mohnke, Oliver; Klitzsch, Norbert; Clauser, Christoph

    2010-05-01

    A major obstacle for an increased use of geothermal energy often lies in the high success risk for the development of geothermal reservoirs due to the unknown rock properties. In general, the ranges of porosity and permeability in existing compilations of rock properties are too large to be useful to constrain properties for specific sites. Usually, conservative assumptions are made about these properties, resulting in greater drilling depth and increased exploration cost. In this study, data from direct measurements on thirty-three sandstones from different borehole locations and depths enable to derive statistical values of the desired hydraulic properties for selected sandstones in the German subsurface. We used Nuclear Magnetic Resonance (NMR) measurements to estimate the porosity and the permeability of sandstones from North Rhine-Westphalia (Germany). Besides NMR standard poro-perm-measurements were performed on the samples to obtain independent data sets for comparison. Porosity was measured by Archimedes principle and pore-size distribution by mercury injection. Also permeability was determined by gas flow measurements taking into account the Klinkenberg effect. The porosities of the studied samples vary between 0 % and 16 %. NMR yields suitable porosity results whereas the porosities obtain by T1 relaxation measurements fit better to the Archimedes porosities than the porosities obtained by T2 relaxation measurements. For porosities up to 10 %, T2 relaxation measurements overestimate the porosity. Furthermore, we calculate the effective porosity using a cutoff time of 3 ms. This effective porosity agrees much better with Archimedes porosities, particularly for the low porosity samples. The gas permeability of studied sandstones varies between 10-21 m2 and 2.10-17 m2. A large number of empirical relationships between relaxation times and gas permeability have been published. We have applied several of these relationships to select the appropriate law for

  5. Mechanical compaction in Bleurswiller sandstone: effective pressure law and compaction localization

    Science.gov (United States)

    Baud, Patrick; Reuschlé, Thierry; Ji, Yuntao; Wong, Teng-fong

    2016-04-01

    We performed a systematic investigation of mechanical compaction and strain localization in Bleurswiller sandstone of 24% porosity. 70 conventional triaxial compression experiments were performed at confining pressures up to 200 MPa and pore pressures ranging from 5 to 100 MPa. Our new data show that the effective pressure principle can be applied in both the brittle faulting and cataclastic flow regimes, with an effective pressure coefficient close to but somewhat less than 1. Under relatively high confinement, the samples typically fail by development of compaction bands. X-ray computed tomography (CT) was used to resolve preexisting porosity clusters, as well as the initiation and propagation of the compaction bands in deformed samples. Synthesis of the CT and microstructural data indicates that there is no casual relation between collapse of the porosity clusters in Bleurswiller sandstone and nucleation of the compaction bands. Instead, the collapsed porosity clusters may represent barriers for the propagation of compaction localization, rendering the compaction bands to propagate along relatively tortuous paths so as to avoid the porosity clusters. The diffuse and tortuous geometry of compaction bands results in permeability reduction that is significantly lower than that associated with compaction band formation in other porous sandstones. Our data confirm that Bleurswiller sandstone stands out as the only porous sandstone associated with a compactive cap that is linear, and our CT and microstructural observation show that it is intimately related to collapse of the porosity clusters. We demonstrate that the anomalous linear caps and their slopes are in agreement with a micromechanical model based on the collapse of a spherical pore embedded in an elastic-plastic matrix that obeys the Coulomb failure criterion.

  6. Wettability Alteration of Sandstones by Silica Nanoparticle Dispersions with Light and Heavy Crude Oil

    Science.gov (United States)

    Pales, A. R.; Huibers, B. M. J.; Bai, L.; Li, C.; Mu, L.; Ladner, D.; Daigle, H.; Darnault, C. J. G.

    2016-12-01

    In enhanced oil recovery (EOR), nanoparticles with their unique physico-chemical properties present a promising method for altering wettability. Nanoparticles could create a water-wet surface in a reservoir rather than an oil-wet one which would ease petroleum recovery. This research examines how uncoated silica nanoparticles alter the wettability of two sandstone surfaces, Berea and Boise, by measuring the contact angle and interfacial tension of different systems as an indicator of wettability. The silica nanoparticles were suspended in brine and brine plus a nonionic surfactant at concentrations of 0, 0.001, and 0.01 wt%. The differential impact on heavy and light crude oils was characterized as well. The study showed that surfactants had a greater impact on interfacial tension (IFT). The IFT decreased with the introduction of surfactants by 79% and 54% for light and heavy crude oils respectively. This reduction in IFT translates to less pressure needed for petroleum recovery. For the contact angle, images collected depict the reduction of contact angle with increased nanoparticle concentration across all oil, sandstone, and reservoir types. In addition to the images taken, the contact angles measured significantly decreased when nanoparticles were introduced with reductions reaching up to 93% between 0 and 0.001 wt% nanoparticles with light oil on the Berea sandstone. As nanoparticle concentration increased, the sandstones became increasingly water-wet for both oil types, and the increasing concentration impacted the light crude oil more than the heavy crude oil. The research evinced that nanoparticles can be used with surfactants in light and heavy crude oil systems to increase the hydrophilicity of Berea and Boise sandstones.

  7. Effect of specimen size on energy dissipation characteristics of red sandstone under high strain rate

    Institute of Scientific and Technical Information of China (English)

    Li Ming; Mao Xianbiao; Lu Aihong; Tao Jing; Zhang Guanghui; Zhang Lianying; Li Chong

    2014-01-01

    In this experiment, red sandstone specimens, having slenderness ratios of 0.5, 0.7, 0.9 and 1.1 respec-tively, were subjected to blow tests using a Split Hopkinson Pressure Bar (SHPB) system at a pressure of 0.4 atmospheres. In this paper, we have analyzed the effect of slenderness ratio on the mechanical properties and energy dissipation characteristics of red sandstone under high strain rates. The processes of compaction, elastic deformation and stress softening deformation of specimens contract with an increase in slenderness ratio, whilst the nonlinear deformation process extends correspondingly. In addi-tion, degrees of damage of specimens reduced gradually and the type of destruction showed a transfor-mation trend from stretching failure towards shear failure when the slenderness ratio increased. A model of dynamic damage evolution in red sandstone was established and the parameters of the constitutive model at different ratios of length to diameter were determined. By comparison with the experimental curve, the accuracy of the model, which could reflect the stress-strain dynamic characteristics of red sandstone, was verified. From the view of energy dissipation, an increase in slenderness ratio of a specimen decreased the proportion of energy dissipation and caused a gradual fall in the capability of energy dissipation during the specimen failure process. To some extent, the study indicated the effects of slenderness ratios on the mechanical properties and energy dissipation characteristics of red sandstone under the high strain rate, which provides valuable references to related engineering designs and academic researches.

  8. Characteristics of bleaching of sandstone in northeast of Ordos Basin and its relationship with natural gas leakage

    Institute of Scientific and Technical Information of China (English)

    MA; YanPing; LIU; ChiYang; ZHAO; JunFeng; HUANG; Lei; YU; Lin; WANG; JianQiang

    2007-01-01

    Bleaching of sandstone has significant applications to tracing hydrocarbon pathways and evaluating the scale of natural gas seepage. Bleaching of sandstones in the northeast of Ordos Basin is mainly distributed in the Mesozoic Yan'an Formation. Studying on petrology, major elements, REEs and trace elements of bleached sandstones and comparing with adjacent sandstones, combining with geologic-geochemical evidences of gas seepage in the northeast of the basin, the bleached sandstones are formed in the acid environment and reducing fluids. Characteristics of petrology show that the contents of kaolinite are high and the color of margin of ferric oxide minerals is lighter than that of the center. Major elements of sandstone samples show high contents of Al2O3 and low ratio of Fe3+/Fe2+. The TFe2O3 content of the bleached sandstone is lower than that of red rock. REE data show that bleached sandstones have low ∑REE contents and Eu-depleted and slightly Ce-enriched. Trace elements show that the bleached sandstones enrich in Co, deplete in Sr, and slightly enrich in Zr and Hf which are close to the values for the green alteration sandstones, and slightly lower than ore-bearing sandstones. Geochemical characteristics of oil-bearing sandstone in the northern basin suggest that the oil-shows are formed by matured Carboniferous-Permian coal bed methane escaping to the surface, and natural gas in field could migrate to the north margin of the basin. The δ13C (PDB) andδ18O(PDB) values of calcite cement in the study area range from -11.729‰ to -10.210‰ and -14.104‰ to -12.481‰, respectively. Theδ13C (PDB) values less than -10‰ imply the carbon sources part from organic carbon. Comprehensive study suggests that the gas leakage has occurred in the northeastern basin, which is responsible for bleaching of the sandstone on top of the Yan'an Formation.

  9. Process Fairness and Dynamic Consistency

    NARCIS (Netherlands)

    S.T. Trautmann (Stefan); P.P. Wakker (Peter)

    2010-01-01

    textabstractAbstract: When process fairness deviates from outcome fairness, dynamic inconsistencies can arise as in nonexpected utility. Resolute choice (Machina) can restore dynamic consistency under nonexpected utility without using Strotz's precommitment. It can similarly justify dynamically

  10. Gravitation, Causality, and Quantum Consistency

    CERN Document Server

    Hertzberg, Mark P

    2016-01-01

    We examine the role of consistency with causality and quantum mechanics in determining the properties of gravitation. We begin by constructing two different classes of interacting theories of massless spin 2 particles -- gravitons. One involves coupling the graviton with the lowest number of derivatives to matter, the other involves coupling the graviton with higher derivatives to matter, making use of the linearized Riemann tensor. The first class requires an infinite tower of terms for consistency, which is known to lead uniquely to general relativity. The second class only requires a finite number of terms for consistency, which appears as a new class of theories of massless spin 2. We recap the causal consistency of general relativity and show how this fails in the second class for the special case of coupling to photons, exploiting related calculations in the literature. In an upcoming publication [1] this result is generalized to a much broader set of theories. Then, as a causal modification of general ...

  11. Stratigraphy and sedimentology of a basement-onlapping shallow marine sandstone succession, the Charcot Bugt Formation, Middle-Upper Jurassic, East Greenland

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, M.; Piasecki, S. [Geological Survey of Denmark and Greenland, Copenhagen (Denmark)]. Geocenter; Surlyk, F. [Univ. of Copenhagen, Copenhagen (Denmark)]. Geological Inst.

    2003-07-01

    A rocky shore developed in early Middle Jurassic times by transgression of the crystalline basement in Milne'Land at the western margin of the East Greenland rift basin. The basement is onlapped by shallow marine sandstones of the Charcot Bugt Formation, locally with a thin fluvial unit at the base. The topography of the onlap surface suggests that a relative sea-level rise of at least 300 m took place in Early Bathonian - Middle Oxfordian times. The sea-level rise was punctuated by relative stillstands and falls during which progradation of the shoreline took place. Palynological data tied to the Boreal ammonite stratigraphy have greatly improved time resolution within the Charcot Bugt Formation, and the Jurassic succession in Milne Land can now be understood in terms of genetically-related depositional systems with a proximal to distal decrease in grain size. The sequence stratigraphic interpretation suggests that translation of the depositional systems governed by relative sea-level changes resulted in stacking of sandstone-dominated falling stage deposits in the Bastern, basinwards parts of Milne Land, whereas thick, remarkably coarsegrained transgressive systems tract deposits formed along the western basin margin. The bulk of the Charcot Bugt Formation consists of stacked sandstone-dominated shoreface units that prograded during highstands. The overall aggradational to backstepping stacking pattem recognised in the Charcot Bugt Formation is comparable to that in the contemporaneous Pelion Formation of the Jameson Land Basin and in correlative units of the mid-Norway shelf and the Northern North Sea. We suggest that the long-term evolution of the depositional systems may have been controlled by long-term eustatic rise acting in concert with relative sea-level changes reflecting regionally contemporaneous phases of rift initiation, dimax and gradual cessation of rifting. (au)

  12. Time-consistent and market-consistent evaluations

    NARCIS (Netherlands)

    Pelsser, A.; Stadje, M.A.

    2014-01-01

    We consider evaluation methods for payoffs with an inherent financial risk as encountered for instance for portfolios held by pension funds and insurance companies. Pricing such payoffs in a way consistent to market prices typically involves combining actuarial techniques with methods from mathemati

  13. Reservoir Characterization of Bridgeport and Cypress Sandstones in Lawrence Field Illinois to Improve Petroleum Recovery by Alkaline-Surfactant-Polymer Flood

    Energy Technology Data Exchange (ETDEWEB)

    Seyler, Beverly; Grube, John; Huff, Bryan; Webb, Nathan; Damico, James; Blakley, Curt; Madhavan, Vineeth; Johanek, Philip; Frailey, Scott

    2012-12-21

    were used to better understand porosity and permeability trends in the region and to characterize barriers and define flow units. Diagenetic alterations that impact porosity and permeability include development of quartz overgrowths, sutured quartz grains, dissolution of feldspar grains, formation of clay mineral coatings on grains, and calcite cementation. Many of these alterations are controlled by facies. Mapping efforts identified distinct flow units in the northern part of the field showing that the Pennsylvanian Bridgeport consists of a series of thick incised channel fill sequences. The sandstones are about 75-150 feet thick and typically consist of medium grained and poorly sorted fluvial to distributary channel fill deposits at the base. The sandstones become indistinctly bedded distributary channel deposits in the main part of the reservoir before fining upwards and becoming more tidally influenced near their top. These channel deposits have core permeabilities ranging from 20 md to well over 1000 md. The tidally influenced deposits are more compartmentalized compared to the thicker and more continuous basal fluvial deposits. Fine grained sandstones that are laterally equivalent to the thicker channel type deposits have permeabilities rarely reaching above 250 md. Most of the unrecovered oil in Lawrence Field is contained in Pennsylvanian Age Bridgeport sandstones and Mississippian Age Cypress sandstones. These reservoirs are highly complex and compartmentalized. Detailed reservoir characterization including the development of 3-D geologic and geocellular models of target areas in the field were completed to identify areas with the best potential to recover remaining reserves including unswept and by-passed oil. This project consisted of tasks designed to compile, interpret, and analyze the data required to conduct reservoir characterization for the Bridgeport and Cypress sandstones in pilot areas in anticipation of expanded implementation of ASP flooding in

  14. Market-consistent actuarial valuation

    CERN Document Server

    Wüthrich, Mario V

    2016-01-01

    This is the third edition of this well-received textbook, presenting powerful methods for measuring insurance liabilities and assets in a consistent way, with detailed mathematical frameworks that lead to market-consistent values for liabilities. Topics covered are stochastic discounting with deflators, valuation portfolio in life and non-life insurance, probability distortions, asset and liability management, financial risks, insurance technical risks, and solvency. Including updates on recent developments and regulatory changes under Solvency II, this new edition of Market-Consistent Actuarial Valuation also elaborates on different risk measures, providing a revised definition of solvency based on industry practice, and presents an adapted valuation framework which takes a dynamic view of non-life insurance reserving risk.

  15. Consistent Histories in Quantum Cosmology

    CERN Document Server

    Craig, David A; 10.1007/s10701-010-9422-6

    2010-01-01

    We illustrate the crucial role played by decoherence (consistency of quantum histories) in extracting consistent quantum probabilities for alternative histories in quantum cosmology. Specifically, within a Wheeler-DeWitt quantization of a flat Friedmann-Robertson-Walker cosmological model sourced with a free massless scalar field, we calculate the probability that the univese is singular in the sense that it assumes zero volume. Classical solutions of this model are a disjoint set of expanding and contracting singular branches. A naive assessment of the behavior of quantum states which are superpositions of expanding and contracting universes may suggest that a "quantum bounce" is possible i.e. that the wave function of the universe may remain peaked on a non-singular classical solution throughout its history. However, a more careful consistent histories analysis shows that for arbitrary states in the physical Hilbert space the probability of this Wheeler-DeWitt quantum universe encountering the big bang/crun...

  16. The Importance of being consistent

    CERN Document Server

    Wasserman, Adam; Jiang, Kaili; Kim, Min-Cheol; Sim, Eunji; Burke, Kieron

    2016-01-01

    We review the role of self-consistency in density functional theory. We apply a recent analysis to both Kohn-Sham and orbital-free DFT, as well as to Partition-DFT, which generalizes all aspects of standard DFT. In each case, the analysis distinguishes between errors in approximate functionals versus errors in the self-consistent density. This yields insights into the origins of many errors in DFT calculations, especially those often attributed to self-interaction or delocalization error. In many classes of problems, errors can be substantially reduced by using `better' densities. We review the history of these approaches, many of their applications, and give simple pedagogical examples.

  17. CHARACTERIZATION OF SANDSTONE RESERVOIRS FOR ENHANCED OIL RECOVERY: THE PERMIAN UPPER MINNELUSA FORMATION, POWDER RIVER BASIN, WYOMING.

    Science.gov (United States)

    Schenk, C.J.; Schmoker, J.W.; Scheffler, J.M.

    1986-01-01

    Upper Minnelusa sandstones form a complex group of reservoirs because of variations in regional setting, sedimentology, and diagenetic alteration. Structural lineaments separate the reservoirs into northern and southern zones. Production in the north is from a single pay sand, and in the south from multi-pay sands due to differential erosion on top of the Upper Minnelusa. The intercalation of eolian dune, interdune, and sabkha sandstones with marine sandstones, carbonates, and anhydrites results in significant reservoir heterogeneity. Diagenetic alterations further enhance heterogeneity, because the degree of cementation and dissolution is partly facies-related.

  18. Consistent supersymmetric decoupling in cosmology

    NARCIS (Netherlands)

    Sousa Sánchez, Kepa

    2012-01-01

    The present work discusses several problems related to the stability of ground states with broken supersymmetry in supergravity, and to the existence and stability of cosmic strings in various supersymmetric models. In particular we study the necessary conditions to truncate consistently a sector o

  19. Experimental study of two-phase fluid flow in two different porosity types of sandstone by P-wave velocity and electrical Impedance measurement

    Science.gov (United States)

    Honda, H.; Mitani, Y.; Kitamura, K.; Ikemi, H.; Takaki, S.

    2015-12-01

    Carbon dioxide (CO2) capture and storage (CCS) is recently expected as the promising method to reduce greenhouse gas emissions. It is important to investigate CO2 behavior in the reservoir, to evaluate the safety and to account the stored CO2 volume. In this study, experimental investigation is conducted to discuss the relationships between injected fluid speed (Flow rate: FR) or capillary number (Ca) and non-wetting fluid flow by compressional wave velocity (Vp) and electrical impedance (Z). In the experiment, N2 and supercritical CO2 were injected into the two sandstones with different porosity (φ), Berea sandstone (φ: 18 %), and Ainoura sandstone (φ: 11.9 %). The dimension of the rock specimens is cored cylinder with a 35 mm diameter and 70 mm height. Experimental conditions are nearly same as the reservoir of deep underground (Confining pressure:15MPa, 40℃). Initial conditions of the specimen are brine (0.1wt%-KCl) saturated. Four piezo-electrical transducers (PZTs) are set on the each surface of the top, middle, lower of the specimen to monitor the CO2 bahavior by Vp. To measuring Z, we use for electrodes method with Ag-AgCl electrodes. Four electrodes are wounded around specimen on the both sides of PZTs. We measured the changes of these parameters with injecting N2, injected fluid speed (FR), the differential pore pressure (DP), N2 saturation (SN2), P-wave velocity (Vp) and electrical impedance (Z), respectively. We also estimated the Ca from measured FR. From these experimental results, there are no obvious Vp changes with increasing Ca, while Z measurement indicates clear and continuous increment. In regards to Vp, Vp reduced at the small FR (0.1 to 0.2 ml/min). As the Ca increases, Vp doesn't indicate large reduction. On the other hand, Z is more sensitive to change the fluid saturation than Vp. It is well-known that both of Vp and Z are the function of fluid saturation. Though, these experimental results are not consistent with previous studies. In

  20. Analysis of single oil-bearing fluid inclusions in mid-Proterozoic sandstones (Roper Group, Australia)

    Science.gov (United States)

    Siljeström, Sandra; Volk, Herbert; George, Simon C.; Lausmaa, Jukka; Sjövall, Peter; Dutkiewicz, Adriana; Hode, Tomas

    2013-12-01

    Hydrocarbons and organic biomarkers extracted from black shales and other carbonaceous sedimentary rocks are valuable sources of information on the biodiversity and environment of early Earth. However, many Precambrian hydrocarbons including biomarkers are suspected of being younger contamination. An alternative approach is to study biomarkers trapped in oil-bearing fluid inclusions by bulk crushing samples and subsequently analysing the extracted hydrocarbons with gas chromatography-mass spectrometry. However, this method does not constrain the hydrocarbons to one particular oil inclusion, which means that if several different generations of oil inclusions are present in the sample, a mix of the content from these oil inclusions will be analysed. In addition, samples with few and/or small inclusions are often below the detection limit. Recently, we showed that it is possible to detect organic biomarkers in single oil-bearing fluid inclusions using time-of-flight secondary ion mass spectrometry (ToF-SIMS). In the present study, single fluid inclusion analysis has been performed on Proterozoic samples for the first time. Four individual oil-bearing fluid inclusions, found in 1430 Ma sandstone from the Roper Superbasin in Northern Australia, were analysed with ToF-SIMS. The ToF-SIMS spectra of the oil in the different inclusions are very similar to each other and are consistent with the presence of n-alkanes/branched alkanes, monocyclic alkanes, bicyclic alkanes, aromatic hydrocarbons, and tetracyclic and pentacyclic hydrocarbons. These results are in agreement with those obtained from bulk crushing of inclusions trapped in the same samples. The capability to analyse the hydrocarbon and biomarker composition of single oil-bearing fluid inclusions is a major breakthrough, as it opens up a way of obtaining molecular compositional data on ancient oils without the ambiguity of the origin of these hydrocarbons. Additionally, this finding suggests that it will be possible

  1. Consistence of Network Filtering Rules

    Institute of Scientific and Technical Information of China (English)

    SHE Kun; WU Yuancheng; HUANG Juncai; ZHOU Mingtian

    2004-01-01

    The inconsistence of firewall/VPN(Virtual Private Network) rule makes a huge maintainable cost.With development of Multinational Company,SOHO office,E-government the number of firewalls/VPN will increase rapidly.Rule table in stand-alone or network will be increased in geometric series accordingly.Checking the consistence of rule table manually is inadequate.A formal approach can define semantic consistence,make a theoretic foundation of intelligent management about rule tables.In this paper,a kind of formalization of host rules and network ones for auto rule-validation based on SET theory were proporsed and a rule validation scheme was defined.The analysis results show the superior performance of the methods and demonstrate its potential for the intelligent management based on rule tables.

  2. Self-consistent triaxial models

    CERN Document Server

    Sanders, Jason L

    2015-01-01

    We present self-consistent triaxial stellar systems that have analytic distribution functions (DFs) expressed in terms of the actions. These provide triaxial density profiles with cores or cusps at the centre. They are the first self-consistent triaxial models with analytic DFs suitable for modelling giant ellipticals and dark haloes. Specifically, we study triaxial models that reproduce the Hernquist profile from Williams & Evans (2015), as well as flattened isochrones of the form proposed by Binney (2014). We explore the kinematics and orbital structure of these models in some detail. The models typically become more radially anisotropic on moving outwards, have velocity ellipsoids aligned in Cartesian coordinates in the centre and aligned in spherical polar coordinates in the outer parts. In projection, the ellipticity of the isophotes and the position angle of the major axis of our models generally changes with radius. So, a natural application is to elliptical galaxies that exhibit isophote twisting....

  3. On Modal Refinement and Consistency

    DEFF Research Database (Denmark)

    Nyman, Ulrik; Larsen, Kim Guldstrand; Wasowski, Andrzej

    2007-01-01

    Almost 20 years after the original conception, we revisit several fundamental question about modal transition systems. First, we demonstrate the incompleteness of the standard modal refinement using a counterexample due to Hüttel. Deciding any refinement, complete with respect to the standard...... notions of implementation, is shown to be computationally hard (co-NP hard). Second, we consider four forms of consistency (existence of implementations) for modal specifications. We characterize each operationally, giving algorithms for deciding, and for synthesizing implementations, together...

  4. Tri-Sasakian consistent reduction

    CERN Document Server

    Cassani, Davide

    2011-01-01

    We establish a universal consistent Kaluza-Klein truncation of M-theory based on seven-dimensional tri-Sasakian structure. The four-dimensional truncated theory is an N=4 gauged supergravity with three vector multiplets and a non-abelian gauge group, containing the compact factor SO(3). Consistency follows from the fact that our truncation takes exactly the same form as a left-invariant reduction on a specific coset manifold, and we show that the same holds for the various universal consistent truncations recently put forward in the literature. We describe how the global symmetry group SL(2,R) x SO(6,3) is embedded in the symmetry group E7(7) of maximally supersymmetric reductions, and make the connection with the approach of Exceptional Generalized Geometry. Vacuum AdS4 solutions spontaneously break the amount of supersymmetry from N=4 to N=3,1 or 0, and the spectrum contains massive modes. We find a subtruncation to minimal N=3 gauged supergravity as well as an N=1 subtruncation to the SO(3)-invariant secto...

  5. Geological and petrophysical characterization of the ferron sandstone for 3-D simulation of a fluvial-deltaic reservoir. Annual report, October 1, 1994--September 30, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Chidsey, T.C. Jr.; Allison, M.L.

    1996-05-01

    The objective of the Ferron Sandstone project is to develop a comprehensive, interdisciplinary, quantitative characterization of a fluvial-deltaic reservoir to allow realistic interwell and reservoir-scale models to be developed for improved oil-field development in similar reservoirs world-wide. Quantitative geological and petrophysical information on the Cretaceous Ferron Sandstone in east-central Utah was collected. Both new and existing data is being integrated into a three-dimensional model of spatial variations in porosity, storativity, and tensorial rock permeability at a scale appropriate for inter-well to regional-scale reservoir simulation. Simulation results could improve reservoir management through proper infill and extension drilling strategies, reduction of economic risks, increased recovery from existing oil fields, and more reliable reserve calculations. Transfer of the project results to the petroleum industry is an integral component of the project. This report covers research activities for fiscal year 1994-95, the second year of the project. Most work consisted of developing field methods and collecting large quantities of existing and new data. We also continued to develop preliminary regional and case-study area interpretations. The project is divided into four tasks: (1) regional stratigraphic analysis, (2) case studies, (3) reservoirs models, and (4) field-scale evaluation of exploration strategies.

  6. Chemostratigraphic and sedimentologic evolution of Wajid Group (Wajid Sandstone): An outcrop analog study from the Cambrian to Permian, SW Saudi Arabia

    Science.gov (United States)

    Yassin, Mohamed A.; Abdullatif, Osman M.

    2017-02-01

    The Paleozoic age succession in Saudi Arabia represents one of the most prolific petroleum producing systems in the Arabian Peninsula. This succession is also considered important for unconventional tight gas and shale gas reservoirs. The Wajid Group (Wajid Sandstone) in SW Saudi Arabia consists of four formations, namely, Dibsiyah (Lower and Upper), Sanamah, Khusayyayn and Juwayl from bottom to top. This study investigates the major oxides, trace and rare earth elements for the Wajid Group formations in southwestern Saudi Arabia. We characterize and compare the sandstone types, provenance, tectonic setting, and climate. Moreover, we applied the chemostratigraphic technique for stratigraphic differentiation. Concentrations of certain elements indicate that Wajid Group was deposited in a passive continental margin. The geochemical analysis reveals that Wajid Group sediments were likely derived from the upper and bulk continental crust and mafic igneous provenance. The elemental geochemical data has been applied in this study to improve the stratigraphic subdivision and correlation. Using selected elements, geochemical vertical profiles, binary, and ternary diagrams allow clearly distinguishing between Wajid Group formations. Thus supports the established formation boundaries that constructed using lithostratigraphy and sedimentology. The geochemical elements variation between formations can be related to differences in rock-forming minerals, facies change, climate, and provenance. The results of this study may help in constraining and correlating complex facies strata and can be used as a guide for stratigraphic correlations in the subsurface within the Wajid basin and other equivalent stratigraphic successions within Saudi Arabia.

  7. Structural and microstructural evolution of fault zones in Cretaceous poorly lithified sandstones of the Rio do Peixe basin, Paraiba, NE Brazil

    Science.gov (United States)

    Balsamo, Fabrizio; Nogueira, Francisco; Storti, Fabrizio; Bezerra, Francisco H. R.; De Carvalho, Bruno R.; André De Souza, Jorge

    2017-04-01

    In this contribution we describe the structural architecture and microstructural features of fault zones developed in Cretaceous, poorly lithified sandstones of the Rio do Peixe basin, NE Brazil. The Rio do Peixe basin is an E-W-trending, intracontinental half-graben basin developed along the Precambrian Patos shear zone where it is abutted by the Porto Alegre shear zone. The basin formed during rifting between South America and Africa plates and was reactivated and inverted in a strike-slip setting during the Cenozoic. Sediments filling the basin consist of an heterolithic sequence of alternating sandstones, conglomerates, siltstone and clay-rich layers. These lithologies are generally poorly lithified far from the major fault zones. Deformational structures in the basin mostly consist of deformation band-dominated fault zones. Extensional and strike-slip fault zones, clusters of deformation bands, and single deformation bands are commonly well developed in the proximity of the basin-boundary fault systems. All deformation structures are generally in positive relief with respect to the host rocks. Extensional fault zones locally have growth strata in their hangingwall blocks and have displacement generally view, they are organized in anastomosed segments with high connectivity. They strike E-W to NE-SW, and typically consist of wide fault cores (narrow shear bands, in which bedding is transposed into foliation imparted by grain preferred orientation. Microstructural observations show negligible cataclasis and dominant non-destructive particulate flow, suggesting that extensional fault zones developed in soft-sediment conditions in a water-saturated environment. Strike-slip fault zones commonly overprint the extensional ones and have displacement values typically lower than about 2 m. They are arranged in conjugate system consisting of NNW-SSE- and WNW-ESE-trending fault zones with left-lateral and right-lateral kinematics, respectively. Compared to extensional

  8. Oxfordian-Kimmeridgian (Late Jurassic) reservoir sandstones in the Witch Ground Graben, U. K. North Sea

    Energy Technology Data Exchange (ETDEWEB)

    Harker, S.D. (Occidental Petroleum (Caledonia) Ltd., Aberdeen (United Kingdom)); Mantel, K.A. (Narwhal, London (United Kingdom)); Morton, D.J. (Deminex U.K. Oil and Gas Ltd., London (United Kingdom)); Riley, L.A. (Paleoservices, Watford (United Kingdom))

    1991-03-01

    Oil-bearing Late Jurassic Oxfordian-Kimmeridgian sandstones of the Sgiath and Piper formations are of major economic importance in the Witch Ground Graben. They form the reservoirs in Scott, which in 1993 will be the largest producing North Sea oil field to come on stream for more than a decade. Together with Scott, the Piper, Saltire, Tartan, Highlander, Petronella, Rob Roy, and Ivanhoe fields contained almost 2 Bbbl of recoverable reserves in these formations. The Sgiath and Piper represent two phases of Late Jurassic transgression and regression, initially represented by paralic deposited sand culminating in a wave-dominated delta sequence. The history of the Sgiath and Piper formations is reviewed and lithostratigraphic and biostratigraphic correlations presented to illustrate the distribution of the reservoir sandstones.

  9. A Study of Thin Sandstone Reservoirs by High-resolution Seismic Inversion

    Institute of Scientific and Technical Information of China (English)

    Ning Songhua

    2006-01-01

    In this paper seismic inversion was used as a key technique and the seismic wavelet most suitable to the actual underground situation was extracted with the higher-order statistics algorithm. The wavelets extracted in this way and the wavelets extracted with the seismic statistics techniques were used separately for inverting the seismic data of the southern part of Tahe oilfield, Tarim basin. The results showed that the resolution of the wavelet inversion with the higher-order statistics method was greatly improved, and the wavelet-inverted section could better distinguish the thin sandstone reservoirs of the upper and lower Carboniferous and their lateral distribution, providing a reliable basis of analysis for the study of thin sandstone reservoirs.

  10. Use of thorium as tracer on study of groundwater of Botucatu sandstone

    Energy Technology Data Exchange (ETDEWEB)

    Porto, Paulo Augusto d' A.; Menezes, Maria Angela B.C. de; Moreira, Rubens Martins; Reis Junior, Aluisio Souza; Kastner, Geraldo Frederico, E-mail: paap@cdtn.br, E-mail: menezes@cdtn.br, E-mail: rubens@cdtn.br, E-mail: reisas@cdtn.br, E-mail: gfk@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2013-07-01

    Thorium in some mineral compounds is very difficult to be dissolved in aqueous medium. To study the mobility of thorium in water, one alternative is to complex this element with EDTA, becoming possible to follow the behavior of thorium this medium. This way, in groundwater with low natural radioactivity and low {sup 232}Th activity, thorium can be used as a tracer. This paper describes the application of the complex Th-EDTA as a tracer applying the solution trough a sandstone sample made by rock from Botucatu Sandstone. The objective was to simulate the flow of groundwater inside the original rock aiming at future use of rare-earth elements complexed with EDTA as tracer. Alpha spectrometry technique was used to determine {sup 232}Th in the water samples with {sup 230}Th as inner-standard. (author)

  11. Fluid identification in tight sandstone reservoirs based on a new rock physics model

    Science.gov (United States)

    Sun, Jianmeng; Wei, Xiaohan; Chen, Xuelian

    2016-08-01

    To identify pore fluids, we establish a new rock physics model named the tight sandstone dual-porosity model based on the Voigt-Reuss-Hill model, approximation for the Xu-White model and Gassmann’s equation to predict elastic wave velocities. The modeling test shows that predicted sonic velocities derived from this rock physics model match well with measured ones from logging data. In this context, elastic moduli can be derived from the model. By numerical study and characteristic analyzation of different elastic properties, a qualitative fluid identification method based on Poisson’s ratio and the S-L dual-factor method based on synthetic moduli is proposed. Case studies of these two new methods show the applicability in distinguishing among different fluids and different layers in tight sandstone reservoirs.

  12. Investigation on the suitability of natural sandstone as a gamma dosimeter

    Energy Technology Data Exchange (ETDEWEB)

    Soliman, C. [Physics Department, Faculty of Science, Ain Shams University, Cairo (Egypt)], E-mail: cairosoliman@yahoo.com; Salama, E. [Physics Department, Faculty of Science, Ain Shams University, Cairo (Egypt)

    2009-10-01

    The suitability of sandstone for the gamma radiation dosimetry using thermoluminescence technique is investigated. Its properties are systematically studied utilizing atomic absorption spectrometry, measurements of natural and laboratory-induced blue thermoluminescence emission band, trap depths and storage effects. The emission of the natural blue-band exhibited broad peak at {approx}315 {sup o}C. The thermoluminescence gamma dose response has a linear behavior over the dose range 1-50 Gy followed by sub-linearity at high dose level, with standard deviation in all cases less than {+-}9%. Trapping depths showed a closely spaced set of traps for both the natural and laboratory-induced glow curves. The variation in thermoluminescence signal over 1 week storage period at room temperature was not more than 7%. The thermoluminescence fading effects were explained by the localized transition model. From our results, it is possible to conclude that natural sandstone is a suitable material for accident and industrial dosimetric applications.

  13. Elemental Geochemistry of the Interlayer Oxidation Zone in the Shihongtan Sandstone Type Uranium Deposit, Xinjiang

    Institute of Scientific and Technical Information of China (English)

    CAI Genqing; ZHANG Zimin; LI Shengxiang

    2005-01-01

    According to the oxidation intensity of ore-hosting sandstone, the interlayer oxidation zone of the Shihongtan sandstone-type uranium deposit in the Turpan-Hami basin can be divided into 4 geochemical subzones, namely, intensely-oxidized, weakly-oxidized, redox and unoxidized primary subzones. The elemental geochemical characteristics of the four subzones have been studied in detail, and the results show that U, together with other elements such as Re, Mo, Se, Sr, S,REE, Corganic etc., is enriched in the redox subzone. Re and U have similar geochemical properties in the reduction-oxidation process. The geochemical properties of Mo and Se are similar to those of U in the reduction condition, but different from those of U in the oxidation condition. It is proposed that the ore-hosting layers can provide a curtain mount of uranium for uranium mineralization.

  14. REE/trace element characteristics of sandstone-type uranium deposits in the Ordos Basin

    Institute of Scientific and Technical Information of China (English)

    LING Mingxing; YANG Xiaoyong; SUN Wei; MIAO Jianyu; LIU Chiyang

    2006-01-01

    The major elements, trace elements and REEs were analyzed on the samples collected from the sandstone-type uranium deposits in the Ordos Basin to constrain the mechanism of uranium enrichment. The total REE amount ranges from 36.7 to 701.8 μg/g and the REE distribution patterns of the sandstone-type uranium samples are characterized by LREE enrichment and high REE depletion. The results also indicated a high Y abundance and Eu anomalies between 0.77-1.81. High-precision ICP-MS results showed that U abundances are within the range of 0.73-150 μg/g, showing some strong correlation between U enrichment and related elements such as Ti, V, Zr, Mo, and Au. In addition, Th abundance is correlated with ΣREE.

  15. Production of a Porosity Map by Kriging in Sandstone Reservoirs, Case Study from the Sava Depression

    Directory of Open Access Journals (Sweden)

    Tomislav Malvić

    2008-05-01

    Full Text Available Variogram analyses and usages of geostatistical interpolations have been standard analytical tools in Croatian geology in the last five years. Such analyses have especially been applied in the mapping of petroleum geological data. In this paper, spatial modelling of porosity data and, consequently, kriging mapping are described for a relatively large dataset obtained at an oil field located in the Croatian part of Pannonian basin (Sava depression. Analyzed datasets included porosity values measured in a sandstone reservoir of Pannonian age. The original dataset can be considered as a rare extensive porosity set available for Croatian hydrocarbon reservoirs. It made possible very reliable semivariogram modelling and kriging interpolation of porosity. The obtained results point out kriging as the most appropriate interpolation approach for porosity, but also for other geological data in sandstone reservoirs of Miocene age.

  16. Partially restricted diffusion in a permeable sandstone: observations by stimulated echo PFG NMR.

    Science.gov (United States)

    Fordham, E J; Gibbs, S J; Hall, L D

    1994-01-01

    We demonstrate a variant, insensitive to eddy current effects, of an alternating pulsed field gradient technique designed to null the effect of background gradients in liquid-saturated porous media, using a 38 mm diameter sample of a natural sandstone. Measurements of the effective diffusivity confirm predictions of a decline as the square root of an effective diffusion time. A value of the ratio S/Vp for the dominant pores is extracted, yielding with T1 a value for the surface relaxivity. We test also a geometry-dependent data collapse recently suggested for a range of diffusion times and wavenumbers. The data agree with a sheet-like pore model for this granular sandstone, and fail to agree with a tube-like model; a pore length scale is also extracted.

  17. Simulation of sandstone degradation using large-scale slake durability index testing device

    Directory of Open Access Journals (Sweden)

    Chaowarin Walsri

    2012-11-01

    Full Text Available Large-scale slake durability index tests have been performed on Khok Kruat (KK, Phu Kradung (PK and Phra Wihan(PW sandstone. A rotating drum with a diameter of 64 cm and length of 40 cm was fabricated to accommodate ten rockfragments with a nominal size of 10 cm. Both large-scale and standard-testing were performed under dry and wet conditions.The large-scale test yields rock deterioration twice greater than the small-scale test, primarily due to the greater energyimposed on the rock fragments. The weight losses under wet condition are 12%, 8%, and 3% greater than under dry condition for KK, PK, and PW sandstones, respectively. After 10 test cycles the water absorption values for PW, KK and PKsandstones are 12%, 3%, and 2%, respectively. Rock degradation under the rapid cooling-heating cycles in the laboratory isabout 18 times faster than under the field condition in the northeast of Thailand.

  18. Sandstone composition and provenance of the Rotliegend of the NE German Basin

    Science.gov (United States)

    McCann, Tommy

    1998-03-01

    The NE German Basin contains an approximately 2.5 km thick Rotliegend sedimentary section, subdivided into 4 formations. These were, deposited following the cessation of the Late Carboniferous/Early Permian volcanic episode and a ca. 20 Ma period of erosion and non-deposition. Initial deposition was confined to two areas, but with increasing thermal subsidence the basin extended to the south. Petrographic (190 sandstones) and geochemical (48 sandstones and mudstones) analyses suggested that the sands are quartz-rich and are derived largely from cratonic or recycled sources. Volcanic and sedimentary rock fragments form most of the labile grains. The succession was deposited in a relatively stable tectonic environment with sediment input derived largely from the lower and upper Palaeozoic strata of the Variscan hinterland and the Upper Carboniferous and Lower Permian volcanics. Volcanic input increases with younger stratigraphic units. This is interpreted as resulting from the unroofing of a more basic source.

  19. The results of experimental asbestos research into the washing of bituminized sandstone

    Energy Technology Data Exchange (ETDEWEB)

    Agalarov, M.S.; Mangasarova, A.G.; Zhirnov, B.I.

    1981-01-01

    Bituminized sandstone was exposed to washing by its removal at the Kirmak deposits under the operation of ''Leninneft''' of the National Mining Institute, and the National Mining Institutes Umbaki deposits under the operation of ''Karagandaneft'''. Various compositions were employed as washing agents including an oil-water mixture. The composition of bituminus oil is given and the method used in the preparation of the mixture is presented. Research has indicated that the coefficient for washing the bituminized sandstone hinges on the various compositions of the oil-water washing fluid and the types of bitumins when this process is undertaken at temperatures of 291-293 degrees Calvin. At temperatures of 358-363 degrees Calvin, this relationship disappears and the coefficient for washing aproaches one.

  20. Hydrophobization by Means of Nanotechnology on Greek Sandstones Used as Building Facades

    Directory of Open Access Journals (Sweden)

    Georgios Karagiannis

    2013-01-01

    Full Text Available Modern sustainable architecture indicates the use of local natural stones for building. Greek sandstones from Epirus (Demati, Greece, EN 12440 used as building facades meet aesthetic and have high mechanical properties, but the inevitable interaction between stone materials and natural or anthropogenic weathering factors controls the type, and extent of stone damages. In the present paper, samples of sandstone were treated with a conventional hydrophobic product and four solutions of the same product, enriched with nanosilica of different concentrations. The properties of the treated samples, such as porosity and pore size distribution, microstructure, static contact angle of a water droplet, and durability to deterioration cycles (freeze-thaw were recorded and conclusions were drawn. The research indicates the increased hydrophobic properties in nanosilica solutions but also the optimum content in nanoparticles that provides hydrophobicity without altering the properties of the stone.

  1. Impact of Residual Water on CH4-CO2 Exchange rate in Hydrate bearing Sandstone

    Science.gov (United States)

    Ersland, G.; Birkedal, K.; Graue, A.

    2012-12-01

    It is previously shown that sequestration of CO2 in natural gas hydrate reservoirs may offer stable long term deposition of a greenhouse gas while benefiting from methane production, without adding heat to the process. In this work CH4 hydrate formation and CO2 reformation in sandstone has been quantified in a series of experiments using Magnetic Resonance Imaging. The overall objective was to provide an improved basic understanding of processes involved in formation and production of methane from methane hydrates within porous media, and to provide data for numerical modeling and scaling. CH4 hydrate has been formed repeatedly in Bentheim sandstone rocks to study hydrate growth patterns for various brine salinities and saturations to prepare for subsequent lab-scale methane production tests through carbon dioxide replacement at various residual water saturations. Surface area for CO2 exposure and the role of permeability and diffusion on the CH4-CO2 exchange rate will also be discussed.

  2. Spatial distribution of epibenthic molluscs on a sandstone reef in the Northeast of Brazil

    Directory of Open Access Journals (Sweden)

    AS. Martinez

    Full Text Available The present study investigated the distribution and abundance of epibenthic molluscs and their feeding habits associated to substrate features (coverage and rugosity in a sandstone reef system in the Northeast of Brazil. Rugosity, low coral cover and high coverage of zoanthids and fleshy alga were the variables that influenced a low richness and high abundance of a few molluscan species in the reef habitat. The most abundant species were generalist carnivores, probably associated to a lesser offer and variability of resources in this type of reef system, when compared to the coral reefs. The results found in this study could reflect a normal characteristic of the molluscan community distribution in sandstone reefs, with low coral cover, or could indicate a degradation state of this habitat if it is compared to coral reefs, once that the significantly high coverage of fleshy alga has been recognized as a negative indicator of reef ecosystems health.

  3. Reconstruction of the diagenesis of the fluvial-lacustrine- deltaic sandstones and its influence on the reservoir quality evolution-- Evidence from Jurassic and Triassic sandstones, Yanchang Oil Field, Ordos Basin

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The reservoir quality of Jurassic and Triassic fluvial and lacustrine-deltaic sandstones of the Yanchang Oil Field in the Ordos Basin is strongly influenced by the burial history and facies-related diagenetic events. The fluvial sandstones have a higher average porosity (14.8%) and a higher permeability (12.7×10?3 ?m2) than those of the deltaic sandstones (9.8% and 5.8 ×10?3 ?m2, respectively). The burial compaction, which resulted in 15% and 20% porosity loss for Jurassic and Triassic sandstones, respectively, is the main factor causing the loss of porosity both for the Jurassic and Triassic sandstones. Among the cements, carbonate is the main one that reduced the reservoir quality of the sandstones. The organic acidic fluid derived from organic matter in the source rocks, the inorganic fluid from rock-water reaction during the late diagenesis, and meteoric waters during the epidiagenesis resulted in the formation of dissolution porosity, which is the main reason for the enhancement of reservoir-quality.

  4. Weathering of Pisha-Sandstones in the Wind-Water Erosion Crisscross Region on the Loess Plateau

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Two types of pisha-sandstones of purple sandstones and gray sandstones, widely distributing in the wind-water erosion crisscross region of China, were selected and used in laboratory experiments for a better understanding of the drying-wetting-freezing weathering process resulting from the apportionment of water or salt solution to rock samples. Weathering experiments were carried out under the conditions of environment control (including temperature, moisture and salt solution). All rock samples were frequently subjected to 140 drying-wetting-freezing cycles. The influences of weathering process were evaluated. It was found that the different treatments of moisture and salt solution applications could affect the nature of the weathering products resulting from drying-wetting-freezing. It was also observed that salt solution could effectively alleviate the weathering of pisha-sandstones. Although not all the observations could be explained, it was apparent that simulated environmental factors had both direct and indirect effects on the weathering of rocks.

  5. National Assessment of Oil and Gas Project - Uinta-Piceance Province (020) Depth to the top of the Dakota Sandstone

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This dataset shows depth ranges to the top of the Dakota Sandstone within the Uinta-Piceance Province, northwestern Colorado and northeastern Utah.

  6. Lithofacies characterization of fluvial sandstones from outcrop gamma-ray logs (Loranca Basin, Spain): the influence of provenance

    Energy Technology Data Exchange (ETDEWEB)

    Martinius, A.W.; Geel, C.R. [Delft Univ. of Technology, Subfaculty of Technical Earth Sciences, Delft (Netherlands); Arribas, J. [Universidad Complutense de Madrid, Dept. de Petrologia y Geoquimica, Madrid (Spain)

    2002-07-01

    Natural gamma spectral (NGS) log motifs and cluster analysis were used to characterise outcropping sandstone bodies formed in braided and high-sinuosity streams of the Tertiary Tortola fluvial system of the Loranca Basin (Spain). Five coarse-grained lithofacies comprise these deposits and determine distinct NGS log motif. Cross-plots and cluster analysis of NGS log data of the lithofacies suggest three distinct clusters. These clusters reflect distinct values for sandstones with small sets of ripple lamination, cross-stratification, and conglomerates and pebbles. Ripple-laminated sandstones show the most variability in NGS signature, whereas conglomeratic sandstones show the most uniform signature. Such cluster analysis may be used to assign NGS log data points of unknown origin to a specific fluvial lithofacies under conditions of equal rock provenance and diagenetic history. A sedimentaclastic (i.e. sedimentary parent rock) origin of sediments appears to be the main control on detrital composition that, in turn, varies with grain size. (Author)

  7. Kinetic Modeling of Diagenesis of Eogene Lacustrine Sandstone Reservoirs in the Jianghan Basin, Southeastern China

    Institute of Scientific and Technical Information of China (English)

    倪师军; 卿海若; 唐建武; 周美夫; 李泽琴

    2002-01-01

    In the Tuoshi oilfield, located in the Cenozoic Jianghan Basin of southeastern China, there have been found hydrocarbon reservoirs hosted in lacustrine sandstones of the Eogene Xingouzui Formation. The main diagenetic features identified in these sandstones include the dissolution of detrital K-feldspar and albite grains, the precipitation of quartz as overgrowths and/or cements, and the precipitation and/or transformation of clay minerals. These diagenetic features were interpreted to have occurred in early, intermediate and late stages, based on the burial depth. The kinetics of fluid-mineral reactions and the concentrations of aqueous species at each stage of diagenesis were simulated numerically for these lacustrine sandstones, using a quasi-stationary state approximation that incorporates simultaneous chemical reactions in a time-space continuum. During the early diagenetic stage, pore fluid was weakly acidic, which resulted in dissolution of K-feldspar and albite and, therefore, led to the release of K + , Na + , Al3 + and SiO2(aq) into the diagenetic fluid. The increased K+ , Na + , Al3+ and SiO2(aq) concentrations in the diagenetic fluid caused the precipitation of quartz, kaolinite and illite. At the beginning of the intermediate diagenetic stage the concentration of H + was built up due to the decomposition of organic matter, which was responsible for further dissolution of K-feldspar and albite and precipitation of quartz, kaolinite, and illite. During the late diagenetic stage, the pore fluid was weakly alkaline, K-feldspar became stable and was precipitated with quartz and clay minerals.When the burial depth was greater than 3000 m, the pore fluids became supersaturated with respect to albite, but undersaturated with respect to quartz, resulting in the precipitation of albite and the dissolution of quartz. The diagenetic reactions forecasted in the numerical modeling closely matched the diagenetic features identified by petrographic examination, and

  8. Experimental study on the expansive deformation of red sandstone of Hongshanyao

    Institute of Scientific and Technical Information of China (English)

    ZHU Zhen-de(朱珍德); ZHANG Yong(张勇); XING Fu-dong(邢福东); LIU Han-long(刘汉龙)

    2004-01-01

    An experience formula of expansive strain and stone taken from a foundation pit of Hongshanyao Project (HSYP) in Nanjing was described. It is clear that the curve of expansive strain-water content is a logarithm. In the meantime, the relation of expansive strain with time was studied and the importance of expansive stabilization time was illuminated. The experiment results indicated that the water content has a tremendous effect on peak expansive and steady expansive deformation of swelling red sandstone.

  9. Giant weathering pits in the Entrada Sandstone, southeastern Utah: Preliminary findings

    Energy Technology Data Exchange (ETDEWEB)

    Netoff, D.I. (Sam Houston State Univ., Huntsville, TX (United States). Dept. of Geography and Geology); Shroba, R.R. (Geological Survey, Denver, CO (United States))

    1993-04-01

    Giant weathering pits formed in outcrops of the lower Entrada Sandstone slickrock of Jurassic age are present in two areas in the Glen Canyon region of arid southeastern Utah. The pits are far larger than any previously described in the geologic literature. The pits near Cookie Jar Butte are commonly cylindrical, typically have low width-to-depth ratios (1.5--3.6), and have a depth of closure of as much as 18 m. There are no obvious lithologic or structural controls that determine their shape or location. Many of the pits at Rock Creek Bay are elongate; several of them have long axes in excess of 53 m, and the longest one is 74 m. Many of the pit walls are breached at the top, and the depth of closure is generally less than 6 m. The shapes of these pits are influenced by point orientation and pit coalescence. Thin-section analyses of near-surface sandstone cores taken near Cookie Jar Butte from pit walls, floors, and rims reveal no significant diagenetic alteration of the fine-grained to very fine frained quartzose sandstone (quartz arenite). Quartz grains appear fresh, and feldspar grains are only slightly weathered. The cement between the grains is mostly CaCO[sub 3]. In several of the pits in both areas sandy sediment veneers the bedrock floor. This sediment is similar in character to the adjacent sandstone and is probably locally derived. Possible origins of the giant pits include various physical, chemical, and biological weathering processes that initiate pit development, followed by excavation by plunge-pool action, wind deflation, dissolution, and piping. Preliminary field and laboratory data do not clearly identify and single process of group of processes that account for pit development.

  10. Depositional setting, structural style, and sandstone distribution in three geopressured geothermal areas, Texas Gulf Coast

    Energy Technology Data Exchange (ETDEWEB)

    Winker, C.D.; Morton, R.A.; Ewing, T.E.; Garcia, D.D.

    1981-10-01

    Three areas in the Texas Gulf Coast region with different depositional settings, structural styles, and sandstone distribution were studied with well log and seismic data to evaluate some of the controls on subsurface conditions in geopressured aquifers. Structural and stratigraphic interpretations were made primarily on the basis of well log correlations. Seismic data confirm the log interpretations but also are useful in structure mapping at depths below well control.

  11. Numerical simulation of multi-dimensional NMR response in tight sandstone

    Science.gov (United States)

    Guo, Jiangfeng; Xie, Ranhong; Zou, Youlong; Ding, Yejiao

    2016-06-01

    Conventional logging methods have limitations in the evaluation of tight sandstone reservoirs. The multi-dimensional nuclear magnetic resonance (NMR) logging method has the advantage that it can simultaneously measure transverse relaxation time (T 2), longitudinal relaxation time (T 1) and diffusion coefficient (D). In this paper, we simulate NMR measurements of tight sandstone with different wettability and saturations by the random walk method and obtain the magnetization decays of Carr-Purcell-Meiboom-Gill pulse sequences with different wait times (TW) and echo spacings (TE) under a magnetic field gradient, resulting in D-T 2-T 1 maps by the multiple echo trains joint inversion method. We also study the effects of wettability, saturation, signal-to-noise ratio (SNR) of data and restricted diffusion on the D-T 2-T 1 maps in tight sandstone. The results show that with decreasing wetting fluid saturation, the surface relaxation rate of the wetting fluid gradually increases and the restricted diffusion phenomenon becomes more and more obvious, which leads to the wetting fluid signal moving along the direction of short relaxation and the direction of the diffusion coefficient decreasing in D-T 2-T 1 maps. Meanwhile, the non-wetting fluid position in D-T 2-T 1 maps does not change with saturation variation. With decreasing SNR, the ability to identify water and oil signals based on NMR maps gradually decreases. The wetting fluid D-T 1 and D-T 2 correlations in NMR diffusion-relaxation maps of tight sandstone are obtained through expanding the wetting fluid restricted diffusion models, and are further applied to recognize the wetting fluid in simulated D-T 2 maps and D-T 1 maps.

  12. Provenance, tectonics and palaeoclimate of Proterozoic Chandarpur sandstones, Chattisgarh basin: A petrographic view

    Indian Academy of Sciences (India)

    Basudeb Datta

    2005-06-01

    Sandstones of early Neoproterozoic Chandarpur Group, Chattisgarh Supergroup, central India display progressive change towards greater textural and mineralogical maturity from base to top of the succession. The clay-silt matrix decreases, sorting of sand grains improves, frequency of rounded grains increases, monocrystalline quartz content increases with concomitant decrease in polycrystalline quartz, feldspar and rock fragments. The trend of variations in different mineralogical and textural attributes, however, exhibits inflections at different stratigraphic levels. The sandstones of the basal Lohardih Formation are alluvial fan deposits, characterized by high matrix and feldspar content, iron-oxide impregnated highly angular grains and poor sorting. Petrographic properties collectively indicate that the sandstones were derived from a weathered granitic crust under a humid climatic condition. Abundance of well rounded grains within the alluvial fan and overlying braided fluvial deposit indicates prolonged wind action during episodes of high aridity. The shallow marine deposit overlying the fluvial deposits in the upper part of the Lohardih Formation exhibits bedto- bed variation in the frequency of angular grains, feldspar content and overall maturity suggesting environmentally controlled segregation of sediments. The abrupt appearance of coarse-grained immature sandstones with concomitant reappearance of iron-oxide impregnated/altered feldspar grains in the upper part of the shelf deposits of the Chaporadih Formation point to a phase of tectonic uplift that possibly triggered a regression. Continued regression and peneplanation heralded the deposition of supermature medium-grained purple quartzarenite of the upper shoreface Kansapathar Formation in the uppermost part of the Chandarpur succession under a hot desertic climatic condition. The provenance analysis revealed that the Chandarpur clastics were derived from granites and granite–gneisses of a continental

  13. The Influence of NaCl Crystallization on the Long-Term Mechanical Behavior of Sandstone

    Science.gov (United States)

    Zheng, Hong; Feng, Xia-Ting; Jiang, Quan

    2015-01-01

    Salt precipitation can occur in saline aquifers when the pore-fluid concentration exceeds saturation during carbon dioxide sequestration, especially in the dry-out region closest to the wellbore. Results from uniaxial and triaxial compression tests, creep tests, and poromechanical tests indicate that NaCl crystallization in pores enhances the compressive strength and bulk modulus under the given confining pressure, and reduces creep. In addition, it makes the pore liquid pressure in the sandstone less sensitive to changes in the hydrostatic stress under undrained conditions. A poro-viscoelastic model with crystals in the pores is proposed to quantitatively estimate the influence of in-pore NaCl crystallization on the long-term mechanical behavior of sandstone. By considering the thermodynamics of crystallization, a geometrical model of a crystal in a pore space is applied to the quasi-static equilibrium state of the crystallization. The solid-liquid interfacial energy is introduced to provide a convenient approach to couple the mechanical properties of sandstone (as a porous material) and the thermochemistry of the in-pore NaCl crystallization. By adding the solid-liquid interfacial energy, the Clausius-Duhem inequality for the skeleton is established for the viscoelasticity based on the proposed geometrical model of a crystal in the pore space. The constitutive equations are deduced from the free energy balance relationship to evaluate the influence of crystallization on the effective stress in terms of the solid-liquid interfacial energies and the pore-size distribution. By comparing the model's output with the test results, it is found that the poro-viscoelastic model describes the influence of in-pore NaCl crystallization on the long-term mechanical behavior of the sandstone reasonably well.

  14. A New Multichelating Acid System for High-Temperature Sandstone Reservoirs

    Directory of Open Access Journals (Sweden)

    Nianyin Li

    2015-01-01

    Full Text Available Sandstone reservoir acidizing is a complex and heterogeneous acid-rock reaction process. If improper acid treatment is implemented, further damage can be induced instead of removing the initial plug, particularly in high-temperature sandstone reservoirs. An efficient acid system is the key to successful acid treatment. High-temperature sandstone treatment with conventional mud acid system faces problems including high acid-rock reaction rate, short acid effective distance, susceptibility to secondary damage, and serious corrosion to pipelines. In this paper, a new multichelating acid system has been developed to overcome these shortcomings. The acid system is composed of ternary weak acid, organic phosphonic chelating agent, anionic polycarboxylic acid chelating dispersant, fluoride, and other assisted additives. Hydrogen ion slowly released by multistage ionization in ternary weak acid and organic phosphonic within the system decreases the concentration of HF to achieve retardation. Chelating agent and chelating dispersant within the system inhibited anodic and cathodic reaction, respectively, to protect the metal from corrosion, while chelating dispersant has great chelating ability on iron ions, restricting the depolarization reaction of ferric ion and metal. The synergic effect of chelating agent and chelating dispersant removes sulfate scale precipitation and inhibits or decreases potential precipitation such as CaF2, silica gel, and fluosilicate. Mechanisms of retardation, corrosion-inhibition, and scale-removing features have been discussed and evaluated with laboratory tests. Test results indicate that this novel acid system has good overall performance, addressing the technical problems and improving the acidizing effect as well for high-temperature sandstone.

  15. Heavy mineral sorting in downwards injected Palaeocene sandstone, Siri Canyon, Danish North Sea

    DEFF Research Database (Denmark)

    Kazerouni, Afsoon Moatari; Friis, Henrik; Svendsen, Johan Byskov

    2011-01-01

    near the Danish Central Graben of the North Sea hydrocarbon province. The emplacement of large-scale injectite complexes has been commonly attributed to seismic activity and consequent sand liquefaction. However, due to very small differences in textural and compositional properties, and the lack...... /geochemical distinction between "in situ" sandstones and their related injectites, especially where primary sedimentary structures are removed by fluidization or minor remobilization....

  16. Imaging pore space in tight gas sandstone reservoir: insights from broad ion beam cross-sectioning

    OpenAIRE

    Konstanty J.; Kukla P.A.; Urai J.L.; Baerle C.; Enzmann F.; Desbois G.

    2010-01-01

    Monetization of tight gas reservoirs, which contain significant gas reserves world-wide, represents a challenge for the entire oil and gas industry. The development of new technologies to enhance tight gas reservoir productivity is strongly dependent on an improved understanding of the rock properties and especially the pore framework. Numerous methods are now available to characterize sandstone cores. However, the pore space characterization at pore scale remains difficult due to the f...

  17. Origin of brackish groundwater in a sandstone aquifer on Bornholm, Denmark

    DEFF Research Database (Denmark)

    Jørgensen, Niels Oluf; Heinemeier, Jan

    2008-01-01

    ). The occurrence of brackish groundwater is remarkable for this aquifer, which otherwise yields potable groundwater of good quality. The stable isotope (18O and 2H) compositions indicate a meteoric origin of the brackish groundwater, which rules out seawater intrusion into the aquifer. 14C activities show apparent...... reflecting long water-rock interaction and suggest a contribution of palaeowater from the fractured crystalline basement which has intruded into the Lower Cambrian sandstone aquifer....

  18. Improving recovery efficiency of water-drive channel sandstone reservoir by drilling wells laterally

    Energy Technology Data Exchange (ETDEWEB)

    Zhiguo, F.; Quinglong, D.; Pingshi, Z.; Bingyu, J.; Weigang, L. [Research Institute of Exploration and Development, Daqing (China)

    1998-12-31

    Example of drilling a horizontal well in reservoir rock of only four meter thick by using existing casing pipe of low efficiency vertical wells to induce production in the top remaining reservoir is described. The experience shows that drilling horizontal wells laterally in thin bodies of sandstone reservoirs and improve their productivity is a feasible proposition. Productivity will still be low, but it can be improved by well stimulation. 3 refs., 3 figs.

  19. Consistency in behavior of the CEO regarding corporate social responsibility

    NARCIS (Netherlands)

    Elving, W.J.L.; Kartal, D.

    2012-01-01

    Purpose - When corporations adopt a corporate social responsibility (CSR) program and use and name it in their external communications, their members should act in line with CSR. The purpose of this paper is to present an experiment in which the consistent or inconsistent behavior of a CEO was

  20. Life Expectancy of Kibbutz Members.

    Science.gov (United States)

    Leviatan, Uri; And Others

    1986-01-01

    Data are presented demonstrating that the life expectancy of kibbutz members--both men and women--is higher than that of the overall Jewish population in Israel. These data add to and support other research findings illustrating the more positive mental health and well-being found among kibbutz members than among other comparative populations.…

  1. Profile Report: ASHA Member Survey.

    Science.gov (United States)

    Weinberg, Armin D.; And Others

    1981-01-01

    The American School Health Association (ASHA) surveyed its members who were nurses to identify their needs for improved member programs and services. Recommendations include that the needs of both school-based nurses and those with administrative roles be considered independently for annual meeting programs. (JN)

  2. Life Expectancy of Kibbutz Members.

    Science.gov (United States)

    Leviatan, Uri; And Others

    1986-01-01

    Data are presented demonstrating that the life expectancy of kibbutz members--both men and women--is higher than that of the overall Jewish population in Israel. These data add to and support other research findings illustrating the more positive mental health and well-being found among kibbutz members than among other comparative populations.…

  3. Reactive transport modeling of coupled feldspar dissolution and secondary mineral precipitation and its implication for diagenetic interaction in sandstones

    Science.gov (United States)

    Yuan, Guanghui; Cao, Yingchang; Gluyas, Jon; Jia, Zhenzhen

    2017-06-01

    Dissolution of feldspars and precipitation of secondary minerals (kaolinite, illite and quartz) are significant diagenetic processes in arkosic sandstones. We examined moderately buried sandstones in the Eocene Shahejie Formation from two sags in the Bohai Bay Basin, East China. Three different types of mineral assemblages (MA) were identified: extensively leached feldspars with a large amount of authigenic kaolinite and quartz cement (MA-1), extensively leached feldspars with a large amount of authigenic kaolinite and minor quartz cement (MA-2), and extensively leached feldspars with a small amount of both authigenic kaolinite and quartz cement (MA-3). Numerical simulations at the continuum scale using Geochemist's Workbench 9.0 were conducted to decipher the origin of the different mineral assemblages. The physicochemical reactions including feldspar dissolution, transport of Al3+ and SiO2(aq), and precipitation of kaolinite and quartz are coupled together in these simulations, with constraints of chemical reactions, kinetic law, dispersion, and advection. Modeling results suggest that a dissolution zone, a transitional zone, and a precipitation zone can be formed in a sandstone unit with suitable constraints of temperature, flow rate, fluid composition and mineral reaction rate. And MA-3, MA-2, and MA-1 assemblages develop in these three zones respectively. The higher SiO2(aq) concentration required for the saturation of quartz than for kaolinite and the low Al3+ concentration needed for the saturation of kaolinite lead to the precipitation of only kaolinite in the transitional zone in a geochemical system with feldspar dissolution serving as the dominant source of SiO2(aq) and Al3+. Comparisons between modeling results and observations of natural sandstone diagenesis suggest that an MA-1 assemblage is likely to occur in buried sandstones at high temperatures (>70-80 °C) and low flow rates. An MA-2 assemblage may occur in moderately buried sandstones at

  4. Trap architecture of the Early Cretaceous Sarir Sandstone in the eastern Sirt Basin, Libya

    Energy Technology Data Exchange (ETDEWEB)

    Gras, R. [Schlumberger GeoQuest, Cedex (France); Thusu, B. [Arabian Gulf Oil Company, Benghazi (Libyan Arab Jamahiriya)

    1998-12-31

    The Sarir Sandstone is the principal reservoir for oil accumulations in the eastern Sirt Basin in Libya. The main phase of the rifting in this area took place in the Late Jurassic-Early Cretaceous, during which time the Sarir Sandstone was deposited as a non-marine, intra-continental clastic syn-rift sequence. Although successfully explored from 1959 onwards, the prolific eastern Sirt Basin is in a relatively immature stage of exploration regarding wildcat drilling and 3D seismic data acquisition. The most recent phase of exploration, utilizing 3D seismic techniques, revealed a complex structural development. The trap geometries are often related to E-W trending, basement-controlled fault systems, oblique to the NNW-SSE Sirt Basin trend. The fault systems were active during the Sarir Sandstone deposition, giving rise to structural as well as combined structural-traps. An increased understanding of trap architecture has led to both re-evaluation of older fields and new discoveries. (author)

  5. Nodular features from Proterozoic Sonia Sandstone, Jodhpur Group, Rajasthan: A litho-biotectonic perspective

    Indian Academy of Sciences (India)

    Arvind Singh; Vikash Anand; Prabhas Pandey; Partha Pratim Chakraborty

    2013-04-01

    The Sonia Sandstone of Proterozoic Jodhpur Group, Marwar Supergroup, exposed around the Sursagar dam area of Jodhpur town, Rajasthan exposes two varieties of nodular features, often spectacular in shape and size. On the basis of mode of occurrence (intra- or interbed) and stratal involvement (single or multiple) the features are classified as Type I and II. From granulometric and microscopic (optical and scanning electron) studies carried out on sandstones from the nodules and their host sandstones, geochemical analysis (SEM-EDAX) of intragranular cement present within Type I nodules, and appreciation of control of associated fracture system within Type II nodules, it is proposed that the two types of nodules vary in their formative mechanism and stage of formation. While Type I nodules are identified as product of processes operative at the early diagenetic, pre-lithification stage, the Type II nodules are undoubtedly the result of post-lithification origin triggered by formation of fracture system. Here we propose generation of vapour pressure (not exceeding the overlying hydrostatic pressure) by decay of thin, laterally impersistent organic mat as the causal factor for intrabed nodule (Type I) formation, which forced rarefication of local grain packing \\tetit {vis-a-vis} early diagenetic silica cementation. The study warrants necessity of more studies on nodules to understand possible roles of organic matter and bedtransgressive fracture systems in their formation, going beyond the generalised secondary mineralization hypothesis.

  6. Formation factor in Bentheimer and Fontainebleau sandstones: Theory compared with pore-scale numerical simulations

    Science.gov (United States)

    Ghanbarian, Behzad; Berg, Carl F.

    2017-09-01

    Accurate quantification of formation resistivity factor F (also called formation factor) provides useful insight into connectivity and pore space topology in fully saturated porous media. In particular the formation factor has been extensively used to estimate permeability in reservoir rocks. One of the widely applied models to estimate F is Archie's law (F = ϕ- m in which ϕ is total porosity and m is cementation exponent) that is known to be valid in rocks with negligible clay content, such as clean sandstones. In this study we compare formation factors determined by percolation and effective-medium theories as well as Archie's law with numerical simulations of electrical resistivity on digital rock models. These digital models represent Bentheimer and Fontainebleau sandstones and are derived either by reconstruction or directly from micro-tomographic images. Results show that the universal quadratic power law from percolation theory accurately estimates the calculated formation factor values in network models over the entire range of porosity. However, it crosses over to the linear scaling from the effective-medium approximation at the porosity of 0.75 in grid models. We also show that the effect of critical porosity, disregarded in Archie's law, is nontrivial, and the Archie model inaccurately estimates the formation factor in low-porosity homogeneous sandstones.

  7. In situ measurements of impact-induced pressure waves in sandstone targets

    Science.gov (United States)

    Hoerth, Tobias; Schäfer, Frank; Nau, Siegfried; Kuder, Jürgen; Poelchau, Michael H.; Thoma, Klaus; Kenkmann, Thomas

    2014-10-01

    In the present study we introduce an innovative method for the measurement of impact-induced pressure waves within geological materials. Impact experiments on dry and water-saturated sandstone targets were conducted at a velocity of 4600 m/s using 12 mm steel projectiles to investigate amplitudes, decay behavior, and speed of the waves propagating through the target material. For this purpose a special kind of piezoresistive sensor capable of recording transient stress pulses within solid brittle materials was developed and calibrated using a Split-Hopkinson pressure bar. Experimental impact parameters (projectile size and speed) were kept constant and yielded reproducible signal curves in terms of rise time and peak amplitudes. Pressure amplitudes decreased by 3 orders of magnitude within the first 250 mm (i.e., 42 projectile radii). The attenuation for water-saturated sandstone is higher compared to dry sandstone which is attributed to dissipation effects caused by relative motion between bulk material and interstitial water. The proportion of the impact energy radiated as seismic energy (seismic efficiency) is in the order of 10-3. The present study shows the feasibility of real-time measurements of waves caused by hypervelocity impacts on geological materials. Experiments of this kind lead to a better understanding of the processes in the crater subsurface during a hypervelocity impact.

  8. Methodology for the design of the method of siliceous sandstones operation using special software

    Directory of Open Access Journals (Sweden)

    Luis Ángel Lara-González

    2014-12-01

    Full Text Available The methodologies used for the design of the method of sandstones explotation by descending staggered banks using specialized software tools are reported. The data analyzed were collected in the field for the operating license 14816 in Melgar, Tolima. The characterization of the rock mass was held from physical and mechanical tests, performed on cylindrical test tubes in order to obtain the value of the maximum strenght and elastic modulus of the rock. The direction and dip of the sandstone package was rock. The direction and dip of the sandstone package was determined by using the stereographic projection whit DIPS®  software, and the safety factor of the slope was obtained with established banks whit SLIDE® . The slops are 8 meters high and 8 meters wide whit a tilt angle 60°, which generated a safety factor  of 2.1. The design  of the mining method was carried out with GEOVIA SURPAC® , at an early stage of development ascending to the level 11 of the exploitation, to then start mining in descending order to control the stabiLity of slopes. The results obtained allow a general methodology for the development of projects to optimize the process of evaluation and selection of mining method by using specialized design tools.

  9. Laboratory study of fluid viscosity induced ultrasonic velocity dispersion in reservoir sandstones

    Science.gov (United States)

    He, Tao; Zou, Chang-Chun; Pei, Fa-Gen; Ren, Ke-Ying; Kong, Fan-Da; Shi, Ge

    2010-06-01

    Ultrasonic velocities of a set of saturated sandstone samples were measured at simulated in-situ pressures in the laboratory. The samples were obtained from the W formation of the WXS Depression and covered low to nearly high porosity and permeability ranges. The brine and four different density oils were used as pore fluids, which provided a good chance to investigate fluid viscosity-induced velocity dispersion. The analysis of experimental observations of velocity dispersion indicates that (1) the Biot model can explain most of the small discrepancy (about 2-3%) between ultrasonic measurements and zero frequency Gassmann predictions for high porosity and permeability samples saturated by all the fluids used in this experiment and is also valid for medium porosity and permeability samples saturated with low viscosity fluids (less than approximately 3 mP·S) and (2) the squirt flow mechanism dominates the low to medium porosity and permeability samples when fluid viscosity increases and produces large velocity dispersions as high as about 8%. The microfracture aspect ratios were also estimated for the reservoir sandstones and applied to calculate the characteristic frequency of the squirt flow model, above which the Gassmann’ s assumptions are violated and the measured high frequency velocities cannot be directly used for Gassmann’s fluid replacement at the exploration seismic frequency band for W formation sandstones.

  10. Intersecting faults and sandstone stratigraphy at the Cerro Prieto geothermal field

    Energy Technology Data Exchange (ETDEWEB)

    Vonder Haar, S.; Howard, J.H.

    1980-02-01

    The northwest-southeast trending Cerro Prieto fault is part of a major regional lineament that extends into Sonaro and has characteristics of both a wrench fault and an oceanic transform fault. The distribution of lithologies and temperature within the field was studied by comparing data from well cuttings, cores, well logs, and geochemical analyses. Across the earliest developed portion of the field, in particular along a 1.25-km northeast-southwest section from well M-9 to M-10, interesting correlations emerge that indicate a relationship among lithology, microfracturing, and temperature distribution. In the upper portion of Reservoir A of this stratigraphic section, between 1200 and 1400 m, the percentage of sandstones ranges from 20 to 55. Temperatures are 225/sup 0/ to 275/sup 0/C based on well logs, calcite isotope maxima, and Na-K-Ca indices. The study shows that an isothermal high in this vicinity corresponds to the lowest total percentage of sandstones. Scanning electron microphotographs of well cores and cuttings from sandstone and shale units reveal clogging, mineral dissolution, and mineral precipitation along microfractures. The working hypothesis is that these sandy shale and siltstone facies are most amenable to increased microfracturing and, in turn, such microfracturing allows for higher temperature fluid to rise to shallower depths in the reservoir.

  11. Mixed-Mode Fracture Behavior and Related Surface Topography Feature of a Typical Sandstone

    Science.gov (United States)

    Ren, L.; Xie, L. Z.; Xie, H. P.; Ai, T.; He, B.

    2016-08-01

    The geo-mechanical properties of reservoirs, especially the morphology of the rock surface and the fracture properties of rocks, are of great importance in the modeling and simulation of hydraulic processes. To better understand these fundamental issues, five groups of mixed-mode fracture tests were conducted on sandstone using edge-cracked semi-circular bend specimens. Accordingly, the fracture loads, growth paths and fracture surfaces for different initial mixities of the mixed-mode loadings from pure mode I to pure mode II were then determined. A surface topography measurement for each rough fracture surface was conducted using a laser profilometer, and the fractal properties of these surfaces were then investigated. The fracture path evolution mechanism was also investigated via optical microscopy. Moreover, the mixed-mode fracture strength envelope and the crack propagation trajectories of sandstone were theoretically modeled using three widely accepted fracture criteria (i.e., the MTS, MSED and MERR criterions). The published test results in Hasanpour and Choupani (World Acad Sci Eng Tech 41:764-769, 2008) for limestone were also theoretically investigated to further examine the effectiveness of the above fracture criteria. However, none of these criteria could accurately predict the fracture envelopes of both sandstone and limestone. To better estimate the fracture strength of mixed-mode fractures, an empirical maximum tensile stress (EMTS) criterion was proposed and found to achieve good agreement with the test results. Finally, a uniformly pressurized fracture model was simulated for low pressurization rates using this criterion.

  12. Note on the temporal relationships between sandstone compaction and precipitation of authigenic minerals

    Science.gov (United States)

    Cavazza, William; Dahl, Jeremy

    1990-11-01

    Several diagenetic minerals (i.e., calcite, kaolinite, illite/smectite, dolomite, quartz and chlorite) are present in the sandstones of the Stilo-Capo d'Orlando Formation (Miocene, southern Italy), but calcite and kaolinite are the only major cementing agents. Textural characteristics of calcite- and kaolinite-cemented sandstones are markedly different. Calcite-cemented samples have an average packing density of 82%, and most grains touch each other tangentially. On the other hand, kaolinite-cemented samples are closely packed (average packing density = 95%), and most commonly display long and concavo-convex intergranular contacts. Textural and geochemical data show that calcite precipitated during progressive burial of the Stilo-Capo d'Orlando Formation over temperatures ranging from 39° to 81°C ( δ18O PDB = -5 to -11%), while kaolinite represents the latest cementation episode. Sandstones of the Stilo-Capo d'Orlando Formation illustrate effectively the combined effects of compaction and cementation during progressive burial. Early formation of carbonate cement prevented further compaction, whereas the remaining uncemented portions underwent severe compaction before later precipitation of kaolinite cement.

  13. Experimental study of anisotropy for Berea Sandstone with image-based evaluation

    Science.gov (United States)

    Jeong, Y.; Yun, T.

    2013-12-01

    The rock anisotropy in internal structure of sedimentary rock governs physical behavior of whole body. Spatial composition of mineral and geometry of fabric contributes the anisotropy of rock, influencing on thermal property and wave propagation in internal structure of rock. Thermal conductivity and Wave velocity are important parameters to rock physical properties correlating other key parameters such as strength and elastic modulus. However, the invisibility of anisotropy of rock makes it hard to characterize the internal structure. In this study, 3D X-ray Computed Tomography is used to reveal the orientation of layer in Berea Sandstone based on statistical approach, SPM (Slicing Plane Method) with respect to the uniformly rotated orientation. This study also represents experimental study of thermal conductivity and elastic wave velocity Berea Sandstone. Divided bar method is conducted to get thermal conductivity of rock and elastic wave velocity is evaluated. Result from the statistical study based on image shows that anisotropic ratio for every orientation has unique value and they are coincides with tendency of layer direction. The uniqueness of thermal conductivity and wave velocity based on experimental study is also discussed. 3D Image of Berea Sandstone Result from SPM

  14. On the consistency of MPS

    CERN Document Server

    Souto-Iglesias, Antonio; González, Leo M; Cercos-Pita, Jose L

    2013-01-01

    The consistency of Moving Particle Semi-implicit (MPS) method in reproducing the gradient, divergence and Laplacian differential operators is discussed in the present paper. Its relation to the Smoothed Particle Hydrodynamics (SPH) method is rigorously established. The application of the MPS method to solve the Navier-Stokes equations using a fractional step approach is treated, unveiling inconsistency problems when solving the Poisson equation for the pressure. A new corrected MPS method incorporating boundary terms is proposed. Applications to one dimensional boundary value Dirichlet and mixed Neumann-Dirichlet problems and to two-dimensional free-surface flows are presented.

  15. Measuring process and knowledge consistency

    DEFF Research Database (Denmark)

    Edwards, Kasper; Jensen, Klaes Ladeby; Haug, Anders

    2007-01-01

    with a 5 point Liker scale and a corresponding scoring system. Process consistency is measured by using a first-person drawing tool with the respondent in the centre. Respondents sketch the sequence of steps and people they contact when configuring a product. The methodology is tested in one company...... for granted; rather the contrary, and attempting to implement a configuration system may easily ignite a political battle. This is because stakes are high in the sense that the rules and processes chosen may only reflect one part of the practice, ignoring a majority of the employees. To avoid this situation...

  16. Diagenesis and reservoir quality of the Lower Cretaceous Quantou Formation tight sandstones in the southern Songliao Basin, China

    Science.gov (United States)

    Xi, Kelai; Cao, Yingchang; Jahren, Jens; Zhu, Rukai; Bjørlykke, Knut; Haile, Beyene Girma; Zheng, Lijing; Hellevang, Helge

    2015-12-01

    The Lower Cretaceous Quantou Formation in the southern Songliao Basin is the typical tight oil sandstone in China. For effective exploration, appraisal and production from such a tight oil sandstone, the diagenesis and reservoir quality must be thoroughly studied first. The tight oil sandstone has been examined by a variety of methods, including core and thin section observation, XRD, SEM, CL, fluorescence, electron probing analysis, fluid inclusion and isotope testing and quantitative determination of reservoir properties. The sandstones are mostly lithic arkoses and feldspathic litharenites with fine to medium grain size and moderate to good sorting. The sandstones are dominated by feldspar, quartz, and volcanic rock fragments showing various stages of disintegration. The reservoir properties are quite poor, with low porosity (average 8.54%) and permeability (average 0.493 mD), small pore-throat radius (average 0.206 μm) and high displacement pressure (mostly higher than 1 MPa). The tight sandstone reservoirs have undergone significant diagenetic alterations such as compaction, feldspar dissolution, quartz cementation, carbonate cementation (mainly ferrocalcite and ankerite) and clay mineral alteration. As to the onset time, the oil emplacement was prior to the carbonate cementation but posterior to the quartz cementation and feldspar dissolution. The smectite to illite reaction and pressure solution at stylolites provide a most important silica sources for quartz cementation. Carbonate cements increase towards interbedded mudstones. Mechanical compaction has played a more important role than cementation in destroying the reservoir quality of the K1q4 sandstone reservoirs. Mixed-layer illite/smectite and illite reduced the porosity and permeability significantly, while chlorite preserved the porosity and permeability since it tends to be oil wet so that later carbonate cementation can be inhibited to some extent. It is likely that the oil emplacement occurred

  17. Multielement statistical evidence for uraniferous hydrothermal activity in sandstones overlying the Phoenix uranium deposit, Athabasca Basin, Canada

    Science.gov (United States)

    Chen, Shishi; Hattori, Keiko; Grunsky, Eric C.

    2017-07-01

    The Phoenix U deposit, with indicated resources of 70.2 M lb U3O8, occurs along the unconformity between the Proterozoic Athabasca Group sandstones and the crystalline basement rocks. Principal component analysis (PCA) is applied to the compositions of sandstones overlying the deposit. Among PCs, PC1 accounts for the largest variability of U and shows a positive association of U with rare earth elements (REEs) + Y + Cu + B + Na + Mg + Ni + Be. The evidence suggests that U was dispersed into sandstones together with these elements during the uraniferous hydrothermal activity. Uranium shows an inverse association with Zr, Hf, Th, Fe, and Ti. Since they are common in detrital heavy minerals, such heavy minerals are not the major host of U. The elements positively associated with U are high in concentrations above the deposit, forming a "chimney-like" or "hump-like" distribution in a vertical section. Their enrichment patterns are explained by the ascent of basement fluids through faults to sandstones and the circulation of basinal fluids around the deposit. The Pb isotope compositions of whole rocks are similar to expected values calculated from the concentrations of U, Th, and Pb except for sandstones close to the deposit. The data suggest that in situ decay of U and Th is responsible for the Pb isotope compositions of most sandstones and that highly radiogenic Pb dispersed from the deposit to the proximal sandstones long after the mineralization. This secondary dispersion is captured in PC8, which has low eigenvalue. The data suggests that the secondary dispersion has minor effect on the overall lithogeochemistry of sandstones.

  18. Effect of kaolinite as a key factor controlling the petrophysical properties of the Nubia sandstone in central Eastern Desert, Egypt

    Science.gov (United States)

    Kassab, Mohamed A.; Abu Hashish, Mohamed F.; Nabawy, Bassem S.; Elnaggar, Osama M.

    2017-01-01

    This paper presents the results of a comprehensive petrographical and petrophysical investigation for the Late Cretaceous Nubia sandstone from Wadi Kareem in central Eastern Desert to measure their fluid flow properties and to investigate the effect of kaolinite on their petrophysical characteristics. From the petrographical analyses, scanning electron microscope 'SEM' and the X-ray diffraction 'XRD' analysis, it is shown that the studied sandstone samples are quite homogeneous in mineralogy and can be distinguished into four sedimentary microfacies: quartz arenite as a clean sandstone as well as three kaolinitic microfacies; namely they are kaolinitic quartz arenite, kaolinitic subarkose, and calcareous to kaolinitc quartz arenite. The main recognized diagenetic processes that prevailed during the post-depositional history of the Nubia sandstone are; compaction, cementation, alteration and dissolution of feldspar into kaolinite. The petrophysical potentiality of the studied sandstones was studied using the helium pycnometer, gas permeability and mercury injection confining pressure 'MICP' techniques. The investigated sandstones can be classified into three petrophysical facies with varying reservoir performances. The petrophysical behaviour of these facies is dependent mostly on their kaolinite content and its impact on porosity, permeability, irreducible water saturation, R35 (pore aperture corresponding to mercury saturation of 35% pore volume), R50 (median pore-throat radius), and MHR (the mean hydraulic radius). Therefore, the studied petrophysical facies are comparable to the distinguished petrographical facies.

  19. Diagenesis characteristics and their influence on Porosity and Permeability of sandstone from Yingcheng Formation in Jinshan field

    Institute of Scientific and Technical Information of China (English)

    ZHANG Ruiyao,GAO Fuhong; ZHANG Zhongyue

    2014-01-01

    In order to understand the diagenesis and its influence on Porosity and Permeability of sandstones from Yingcheng Formation in Jinshan field,aPPlying thin sections,casting and scanning electron microscoPe, the authors studied PetrograPhy,diagenesis,Porosity and Permeability of Yingcheng Formation sandstone reser-voir. The results show that the reservoir of Yingcheng Formation is mainly comPosed of lithic arkoses. Sand-stones exPerienced comPaction,Pressolution,cementation,metasomatism and dissolution. The Primary Pores of the sandstones are undeveloPed;most of Pores are the secondary Pores,which are mainly intragranular dissolu-tion Pores in feldsPar and debris. The comPaction and cementation reduced the Primary Pores in sandstones,the Porosity and Permeability decreased;while the dissolution formed the secondary Pores,resulting in the Porosity and Permeability increase. Due to comPaction and cementation,the Porosity and Permeability are reduced with increasing of dePth. There exists an abnormal enlargement of Porosity and Permeability within a dePth range 2 310-2 450 m. In combination with analysis of Petrology,the dissolution of feldsPar and debris is most deve-loPed in the dePth range. Therefore,comPaction,cementation and dissolution are the imPortant factors which affect the Porosity and Permeability of sandstones.

  20. Diagenesis and porosity evolution of sandstone reservoirs in the East Ⅱ part of Sulige gas field, Ordos Basin

    Institute of Scientific and Technical Information of China (English)

    Yang Renchao; Fan Aiping; Han Zuozhen; Wang Xiuping

    2012-01-01

    It is becoming an important controlling factor of gas exploration and exploitation in the east part of Sulige gas field in the Ordos Basin where the reservoir of main gas formations is tight sandstones.Employing experimental methods of slice identification,casting slice,scan electron microscope,and X-ray diffractions,we studied the characteristics of petrology and diagenesis on reservoirs in Shan1 section of Shanxi formation and He8 section of Shihezi formation of the Permian system in the East Ⅱ part of Sulige gas field.The results include:(1) the main sandstones in these areas are dominated by lithic sandstone and lithic silicarenite with low grade of maturity; (2) the diagenesis of sandstone in these areas mainly include compaction,cementation,corrosion and alteration.Conclusions are as follows:(1) the diagenetic stage reached period B of the middle diagenetic stage; (2) the early diagenetic compaction is one of the main factors to decreasing porosity:(3) the secondary pores formed by corrosion in acidity medium conditions in period A of the middle diagenetic stage can distinctly ameliorate the poor reservoir capability of sandstone and; (4) cementation in period B of the middle diagenetic stage is the most important factor leading to poor physical property of sandstone reservoirs.

  1. Construction of pore network models for Berea and Fontainebleau sandstones using non-linear programing and optimization techniques

    Science.gov (United States)

    Sharqawy, Mostafa H.

    2016-12-01

    Pore network models (PNM) of Berea and Fontainebleau sandstones were constructed using nonlinear programming (NLP) and optimization methods. The constructed PNMs are considered as a digital representation of the rock samples which were based on matching the macroscopic properties of the porous media and used to conduct fluid transport simulations including single and two-phase flow. The PNMs consisted of cubic networks of randomly distributed pores and throats sizes and with various connectivity levels. The networks were optimized such that the upper and lower bounds of the pore sizes are determined using the capillary tube bundle model and the Nelder-Mead method instead of guessing them, which reduces the optimization computational time significantly. An open-source PNM framework was employed to conduct transport and percolation simulations such as invasion percolation and Darcian flow. The PNM model was subsequently used to compute the macroscopic properties; porosity, absolute permeability, specific surface area, breakthrough capillary pressure, and primary drainage curve. The pore networks were optimized to allow for the simulation results of the macroscopic properties to be in excellent agreement with the experimental measurements. This study demonstrates that non-linear programming and optimization methods provide a promising method for pore network modeling when computed tomography imaging may not be readily available.

  2. NMR study comparing capillary trapping in Berea sandstone of air, carbon dioxide, and supercritical carbon dioxide after imbibition of water

    Science.gov (United States)

    Prather, Cody A.; Bray, Joshua M.; Seymour, Joseph D.; Codd, Sarah L.

    2016-02-01

    Nuclear magnetic resonance (NMR) techniques were used to study the capillary trapping mechanisms relevant to carbon sequestration. Capillary trapping is an important mechanism in the initial trapping of supercritical CO2 in the pore structures of deep underground rock formations during the sequestration process. Capillary trapping is considered the most promising trapping option for carbon sequestration. NMR techniques noninvasively monitor the drainage and imbibition of air, CO2, and supercritical CO2 with DI H2O at low capillary numbers in a Berea sandstone rock core under conditions representative of a deep underground saline aquifer. Supercritical CO2 was found to have a lower residual nonwetting (NW) phase saturation than that of air and CO2. Supercritical CO2 behaves differently than gas phase air or CO2 and leads to a reduction in capillary trapping. NMR relaxometry data suggest that the NW phase, i.e., air, CO2, or supercritical CO2, is preferentially trapped in larger pores. This is consistent with snap-off conditions being more favorable in macroscale pores, as NW fluids minimize their contact area with the solid and hence prefer larger pores.

  3. Evaluation of consolidating and water repellent treatments applied to the miocene sandstone used in Tunisian Heritage Monuments

    Directory of Open Access Journals (Sweden)

    Zoghlami, K.

    2005-03-01

    Full Text Available Summary The research reported in the present paper focused on the behaviour of the Miocene sandstone used to build the Roman aqueduct at Zaghouan-Carthage and other Tunisian Heritage monuments, after application of water repellent and consolidating treatments as a preliminary to restoration. Commercial consolidants and water repellents were used in the experiments: two ethyl silicate consolidants, Tegovakon (TV and Keim-Silex OH (KSOH; two (siloxane water repellents, Tegosivin THE 328 (THE and Tegosivin HLJ00 (THE; and a dual (consolidate and water repellent action substance, Keim- Silex H (KSH (silicate acid ester base with siloxane. A mixed treatment consisting of successive coats of TV and THL (TVHL was also applied. These organosilicate consolidants and water repellents acted on the porous structure of the sandstone, reducing total porosity and water vapour permeability. The water repellent THE was found to affect these properties least, with a pore size distribution that resembled the distribution in the untreated sandstone most closely. Water repellents diminish water absorption and consolidants increase mechanical strength. The TV-THL mix, which yielded results similar to those obtained with water repellents alone, was unable to prevent the substantial scaling that occurs during (RILEM salt crystallisation-induced artificial ageing. The best results were found with the dual action consolidant! water repellent product (KSH, which improved the mechanical properties while affording protection from the decay caused by salts in artificial ageing trials. This substance was found to reduce water vapour permeability, however

    Esta investigación se centra en la evaluación del comportamiento de la arenisca miocénica utilizada en el acueducto de Zaghouan-Cartago y otros monumentos del Patrimonio Monumental de Túnez tras la aplicación de tratamientos de hidrofugación y de consolidación. Para los tratamientos se han seleccionado productos

  4. Decay of sandstone monuments in Petra (Jordan): Gravity-induced stress as a stabilizing factor

    Science.gov (United States)

    Řihošek, Jaroslav; Bruthans, Jiří; Mašín, David; Filippi, Michal; Schweigstillova, Jana

    2016-04-01

    As demonstrated by physical experiments and numerical modeling the gravity-induced stress (stress in further text) in sandstone massive reduces weathering and erosion rate (Bruthans et al. 2014). This finding is in contrast to common view that stress threatens stability of man-made monuments carved to sandstone. Certain low- levels of gravity-induced stress can in fact stabilize and protect these forms against weathering and disintegration. The purpose of this investigation is to evaluate the effect of the stress on weathering of sandstone monuments at the Petra World Heritage Site in Jordan via field observations, salt weathering experiments, and physical and numerical modeling. Previous studies on weathering of Petra monuments have neglected the impact of stress, but the ubiquitous presence of stress-controlled landforms in Petra suggests that it has a substantial effect on weathering and erosion processes on man-made monuments and natural surfaces. Laboratory salt weathering experiments with cubes of Umm Ishrin sandstone from Petra demonstrated the inverse relationship between stress magnitude and decay rate. Physical modeling with Strelec locked sand from the Czech Republic was used to simulate weathering and decay of Petra monuments. Sharp forms subjected to water erosion decayed to rounded shapes strikingly similar to tombs in Petra subjected to more than 2000 years of weathering and erosion. The physical modeling results enabled visualization of the recession of monument surfaces in high spatial and temporal resolution and indicate that the recession rate of Petra monuments is far from constant both in space and time. Numerical modeling of stress fields confirms the physical modeling results. This novel approach to investigate weathering clearly demonstrates that increased stress decreases the decay rate of Petra monuments. To properly delineate the endangered zones of monuments, the potential damage caused by weathering agents should be combined with stress

  5. Maintaining consistency in distributed systems

    Science.gov (United States)

    Birman, Kenneth P.

    1991-01-01

    In systems designed as assemblies of independently developed components, concurrent access to data or data structures normally arises within individual programs, and is controlled using mutual exclusion constructs, such as semaphores and monitors. Where data is persistent and/or sets of operation are related to one another, transactions or linearizability may be more appropriate. Systems that incorporate cooperative styles of distributed execution often replicate or distribute data within groups of components. In these cases, group oriented consistency properties must be maintained, and tools based on the virtual synchrony execution model greatly simplify the task confronting an application developer. All three styles of distributed computing are likely to be seen in future systems - often, within the same application. This leads us to propose an integrated approach that permits applications that use virtual synchrony with concurrent objects that respect a linearizability constraint, and vice versa. Transactional subsystems are treated as a special case of linearizability.

  6. Late Paleozoic tectonics of the Solonker Zone in the Wuliji area, Inner Mongolia, China: Insights from stratigraphic sequence, chronology, and sandstone geochemistry

    Science.gov (United States)

    Shi, Guanzhong; Song, Guangzeng; Wang, Hua; Huang, Chuanyan; Zhang, Lidong; Tang, Jianrong

    2016-09-01

    The geology in the Wuliji area (including the Enger Us and Quagan Qulu areas) is important for understanding the Late Paleozoic tectonics of the Solonker Zone. Ultramafic/mafic rocks in the Enger Us area, previously interpreted as an ophiolitic suture, are actually lava flows and sills in a Permian turbiditic sequence and a small body of fault breccia containing serpentinite. Subduction zone features, such as accretionary complexes, magmatic arc volcanics or LP/HP metamorphism are absent. Early Permian N-MORB mafic rocks and Late Permian radiolarian cherts accompanied by turbidites and tuffeous rocks indicate a deep water setting. In the Quagan Qulu area, outcrops of the Late Carboniferous to Permian Amushan Formation are composed of volcano-sedimenary rocks and guyot-like reef limestone along with a Late Permian volcano-sedimentary unit. A dacite lava in the Late Permian volcano-sedimentary unit yields a zircon U-Pb age of 254 Ma. The gabbros in the Quagan Qulu area are intruded into the Amushan Formation and caused contact metamorphism of country rocks. Sandstones in the Upper Member of the Amushan Formation contain detrital clasts of volcanic fragments and mineral clasts of crystalline basement rocks (i.e. biotite, muscovite and garnet). Geochemical analysis of volcaniclastic sandstones shows a magmatic affinity to both continental island arc (CIA) and active continental margin (ACM) tectonic settings. A Late Permian incipient rift setting is suggested by analyzing the lithostratigraphic sequence and related magmatism in the Wuliji area. The volcano-sedimentary rocks in the Wuliji area experienced a nearly N-S shortening that was probably related to the Early Mesozoic nearly N-S compression well developed in other areas close to the Wuliji area.

  7. RESERVOIR CHARACTERIZATION OF UPPER DEVONIAN GORDON SANDSTONE, JACKSONBURG STRINGTOWN OIL FIELD, NORTHWESTERN WEST VIRGINIA

    Energy Technology Data Exchange (ETDEWEB)

    S. Ameri; K. Aminian; K.L. Avary; H.I. Bilgesu; M.E. Hohn; R.R. McDowell; D.L. Matchen

    2001-07-01

    The Jacksonburg-Stringtown oil field contained an estimated 88,500,000 barrels of oil in place, of which approximately 20,000,000 barrels were produced during primary recovery operations. A gas injection project, initiated in 1934, and a pilot waterflood, begun in 1981, yielded additional production from limited portions of the field. The pilot was successful enough to warrant development of a full-scale waterflood in 1990, involving approximately 8,900 acres in three units, with a target of 1,500 barrels of oil per acre recovery. Historical patterns of drilling and development within the field suggests that the Gordon reservoir is heterogeneous, and that detailed reservoir characterization is necessary for understanding well performance and addressing problems observed by the operators. The purpose of this work is to establish relationships among permeability, geophysical and other data by integrating geologic, geophysical and engineering data into an interdisciplinary quantification of reservoir heterogeneity as it relates to production. Conventional stratigraphic correlation and core description shows that the Gordon sandstone is composed of three parasequences, formed along the Late Devonian shoreline of the Appalachian Basin. The parasequences comprise five lithofacies, of which one includes reservoir sandstones. Pay sandstones were found to have permeabilities in core ranging from 10 to 200 mD, whereas non-pay sandstones have permeabilities ranging from below the level of instrumental detection to 5 mD; Conglomeratic zones could take on the permeability characteristics of enclosing materials, or could exhibit extremely low values in pay sandstone and high values in non-pay or low permeability pay sandstone. Four electrofacies based on a linear combination of density and scaled gamma ray best matched correlations made independently based on visual comparison of geophysical logs. Electrofacies 4 with relatively high permeability (mean value > 45 mD) was

  8. Decentralized Consistent Updates in SDN

    KAUST Repository

    Nguyen, Thanh Dang

    2017-04-10

    We present ez-Segway, a decentralized mechanism to consistently and quickly update the network state while preventing forwarding anomalies (loops and blackholes) and avoiding link congestion. In our design, the centralized SDN controller only pre-computes information needed by the switches during the update execution. This information is distributed to the switches, which use partial knowledge and direct message passing to efficiently realize the update. This separation of concerns has the key benefit of improving update performance as the communication and computation bottlenecks at the controller are removed. Our evaluations via network emulations and large-scale simulations demonstrate the efficiency of ez-Segway, which compared to a centralized approach, improves network update times by up to 45% and 57% at the median and the 99th percentile, respectively. A deployment of a system prototype in a real OpenFlow switch and an implementation in P4 demonstrate the feasibility and low overhead of implementing simple network update functionality within switches.

  9. The Consistent Vehicle Routing Problem

    Energy Technology Data Exchange (ETDEWEB)

    Groer, Christopher S [ORNL; Golden, Bruce [University of Maryland; Edward, Wasil [American University

    2009-01-01

    In the small package shipping industry (as in other industries), companies try to differentiate themselves by providing high levels of customer service. This can be accomplished in several ways, including online tracking of packages, ensuring on-time delivery, and offering residential pickups. Some companies want their drivers to develop relationships with customers on a route and have the same drivers visit the same customers at roughly the same time on each day that the customers need service. These service requirements, together with traditional constraints on vehicle capacity and route length, define a variant of the classical capacitated vehicle routing problem, which we call the consistent VRP (ConVRP). In this paper, we formulate the problem as a mixed-integer program and develop an algorithm to solve the ConVRP that is based on the record-to-record travel algorithm. We compare the performance of our algorithm to the optimal mixed-integer program solutions for a set of small problems and then apply our algorithm to five simulated data sets with 1,000 customers and a real-world data set with more than 3,700 customers. We provide a technique for generating ConVRP benchmark problems from vehicle routing problem instances given in the literature and provide our solutions to these instances. The solutions produced by our algorithm on all problems do a very good job of meeting customer service objectives with routes that have a low total travel time.

  10. Sandstone provenance and tectonic evolution of the Xiukang Mélange from Neotethyan subduction to India-Asia collision (Yarlung-Zangbo suture, south Tibet)

    Science.gov (United States)

    An, Wei; Hu, Xiumian; Garzanti, Eduardo

    2016-04-01

    The Xiukang Mélange of the Yarlung-Zangbo suture zone in south Tibet documents low efficiency of accretion along the southern active margin of Asia during Cretaceous Neotethyan subduction, followed by final development during the early Paleogene stages of the India-Asia collision. Here we investigate four transverses in the Xigaze area (Jiding, Cuola Pass, Riwuqi and Saga), inquiry the composition in each transverse, and present integrated petrologic, U-Pb detrital-zircon geochronology and Hf isotope data on sandstone blocks. In fault contact with the Yarlung-Zangbo Ophiolite to the north and the Tethyan Himalaya to the south, the Xiukang mélange can be divided into three types: serpentinite-matrix mélange composed by broken Yarlung-Zangbo Ophiolite, thrust-sheets consisting mainly chert, quartzose or limestone sheets(>100m) with little intervening marix, and mudstone-matrix mélange displaying typical blocks-in-matrix texture. While serpentinite-matrix mélange is exposed adjacent to the ophiolite, distributions of thrust-sheets and blocks in mudstone-matrix mélange show along-strike diversities. For example, Jiding transverse is dominant by chert sheets and basalt blocks with scarcely sandstone blocks, while Cuola Pass and Saga transverses expose large amounts of limestone/quartzarenite sheets in the north and volcaniclastic blocks in the south. However, turbidite sheets and volcaniclastic blocks are outcropped in the north Riwuqi transverse with quartzarenite blocks preserved in the south. Three groups of sandstone blocks/sheets with different provenance and depositional setting are distinguished by their petrographic, geochronological and isotopic fingerprints. Sheets of turbiditic quartzarenite originally sourced from the Indian continent were deposited in pre-Cretaceous time on the northernmost edge of the Indian passive margin and eventually involved into the mélange at the early stage of the India-Asia collision. Two distinct groups of volcaniclastic-sandstone

  11. Preliminary observations on the impact of complex stress histories on sandstone response to salt weathering: laboratory simulations of process combinations

    Science.gov (United States)

    McCabe, S.; Smith, B. J.; Warke, P. A.

    2007-03-01

    Historic sandstone structures carry an inheritance, or a ‘memory’, of past stresses that the stone has undergone since its placement in a façade. This inheritance, which conditions present day performance, may be made up of long-term exposure to a combination of low magnitude background environmental factors (for example, salt weathering, temperature and moisture cycling) and, superimposed upon these, less frequent but potentially high magnitude events or ‘exceptional’ factors (for example, lime rendering, severe frost events, fire). The impact of complex histories on the decay pathways of historic sandstone is not clearly understood, but this paper seeks to improve that understanding through the use of a laboratory ‘process combination’ study. Blocks of quartz sandstone (Peakmoor, from NW England) were divided into subsets that experienced different histories (lime rendering and removal, fire and freeze-thaw cycles in isolation and combination) that reflected the event timeline of a real medieval sandstone monument in NE Ireland, Bonamargy Friary (McCabe et al. 2006b). These subsets were then subject to salt weathering cycles using a 10% salt solution of NaCl and MgSO4 that represents the ‘every-day’ stress environment of, for example, sandstone structures in coastal, or polluted urban, location. Block response to salt weathering was monitored by collecting, drying and weighing the debris that was released as blocks were immersed in the salt solution at the beginning of each cycle. The results illustrate the complexity of the stone decay system, showing that seemingly small variations in stress history can produce divergent response to salt weathering cycles. Applied to real-world historic sandstone structures, this concept may help to explain the spatial and temporal variability of sandstone response to background environmental factors on a single façade, and encourage conservators to include the role of stress inheritance when selecting and

  12. Rockfall monitoring of a poorly consolidated marly sandstone cliff by TLS and IR thermography

    Science.gov (United States)

    Lefeuvre, Caroline; Guérin, Antoine; Carrea, Dario; Derron, Marc-Henri; Jaboyedoff, Michel

    2017-04-01

    The study area of La Cornalle (Vaud, Switzerland) is a 40 m high south-west facing cliff which is also part of a larger landslide (Bersier 1975 ; Parriaux, 1998). The cliff is formed by an alternation of marls and sandstones. The thicknesses of sandstone layers range from 0.5 to 4 meters. The rockfall activity of this cliff is high, with an average of one event per day. The aim of this study is to better understand the links between rockfall activity, cliff's structures, and weather and thermal conditions. The 3D surface evolution of the Cornalle cliff is monitored approximately every month since September 2012 using a Terrestrial Laser Scanning (TLS) data in order to get a monthly inventory of rockfall events. Since November 2013, a weather station located 150 meters away from the cliff collects data such as temperature, humidity, atmospheric pressure, rain and solar radiation every 15 minutes. Furthermore, we also fixed a thermic probe in the sandstone at 10 cm deep which measures temperature every 10 minutes. A detailed analysis has been performed during a short period (01/29/2016-04/08/2016) and pointed out a correlation between daily rainfall and rockfall. We found that a fall occurred the day or the day after a cumulative daily rainfall of at least 10 mm/day.In parallel to this monthly monitoring, the northwest part of La Cornalle cliff (the most active part) was monitored for 24 consecutive hours in July 2016 (from 12:30 to 12:30) using infrared thermography and crackmeters with a precision of 0.01mm. We collected a series of thermal pictures every 20 minutes, and measured the opening of a crack in sandstone layers every hour. We observed that marls are more affected by external changes of temperature than sandstones. Their surface temperature rises (resp. falls) more with an increase (resp. decrease) of external temperature than sandstones. Crackmeters measured an opening of the crack with an increase of the rock temperature and the opposite displacement

  13. Utilisation of Sand from Kaolin Washing for the Manufacture of Alkali-activated Artificial Sandstone

    Science.gov (United States)

    Vavro, Martin; Vavro, Leona; Mec, Pavel; Soucek, Kamil; Pticen, Frantisek; Reiterman, Pavel

    2017-04-01

    Sandstones represent a traditional natural stones which are widely used in Czech architecture and sculpture over a long time. Thanks to their relatively easy workability, sandstones provide a wide range of stone products and also represent a popular material for architectural and sculptural purposes. In the field of restoration of artworks, they are therefore often used for manufacturing stone statue copies originally made from the same or similar type of stone. Despite a relatively common and varied occurrence of natural sandstones, the method of the artificial stone facsimiles creation in the form of various cast elements is also often applied in restoration practice. The history of application of artificial stones in civil engineering and architecture goes back to the ancient times, i.e. to Roman antiquity and possibly up to the time of ancient Egypt. The lack of appropriate natural rock, suitable in the view of colour, grain size or texture is the main reason of manufacturing copies based on synthetic mixtures. The other reason is high financial costs to create a sculpture copy from natural materials. Mixtures made from white and/or grey cements, sands, carefully selected crushed stone or well graded natural gravels, and mineral coloring pigments or mixtures with acrylate, polyester, and epoxy resins binder are the most frequently used artificial materials for cast stone manufacturing. This paper aims to bring information about composition and properties of artificial sandstones made from alkali-activated binder mixtures based on metakaolin and granulated blast furnace slag. The filler of this artificial stone is represented by fine-grained sand generated during kaolin wet processing. Used sand is mainly formed by quartz, feldspars, micas (muscovite > biotite), residual kaolin, and to a lesser extent also by Fe oxyhydroxides ("limonite"), titanium dioxide mineral (probably anatase), and carbonate mineral unidentified in detail. Annual Czech production of this

  14. The mineralogical composition of sandstone and its effect on sulphur dioxide deposition

    Directory of Open Access Journals (Sweden)

    Müller, Urs

    2008-06-01

    Full Text Available Air pollutants often accelerate stone deterioration in historical buildings and monuments in urban areas. The pollutants are themselves the products of fossil fuel combustion and intensive farming. While this trend seems to have been curbed by strict emission laws in the European Union, in most developing and emerging countries air pollution is an ongoing process due to increasing energy needs and vehicle traffic. Many factors condition natural stone behaviour with respect to gaseous pollutants. Two of the more prominent of such factors are the composition of the atmosphere and the type of stone. Due to their porosity, sandstones are particularly vulnerable to air pollutant attack. Many of the reactions between non-carbonaceous sandstones and these gases are not well understood, however. The present study aimed to acquire an understanding of the processes and factors governing sandstone behaviour when exposed to sulphur dioxide. Seven different sandstones from southern and eastern Germany were analyzed for the study. The binder composition of the stones varied significantly. They also exhibited completely different behaviour in connection with SO2 sorption. Interestingly, while the amount of SO2 deposited was unrelated to the specific surface area of the sandstones, this parameter was closely correlated to the iron oxide content. Iron oxide phases are believed to act as a catalyst in the oxidation of SO2 to SO3. The type and amount of clay mineral, in turn, was found to have no significant impact on initial SO2 deposition in sandstones.Los contaminantes atmosféricos son con frecuencia responsables de la aceleración de la degradación de la piedra en los edificios y monumentos históricos de las zonas urbanas. Los contaminantes en sí son productos de reacción procedentes de la combustión de los hidrocarburos y de la agricultura intensiva. Dentro de la Comunidad Europea, el avance parece haberse ralentizado mediante restrictivas leyes sobre

  15. Reservoir uncertainty, Precambrian topography, and carbon sequestration in the Mt. Simon Sandstone, Illinois Basin

    Science.gov (United States)

    Leetaru, H.E.; McBride, J.H.

    2009-01-01

    Sequestration sites are evaluated by studying the local geological structure and confirming the presence of both a reservoir facies and an impermeable seal not breached by significant faulting. The Cambrian Mt. Simon Sandstone is a blanket sandstone that underlies large parts of Midwest United States and is this region's most significant carbon sequestration reservoir. An assessment of the geological structure of any Mt. Simon sequestration site must also include knowledge of the paleotopography prior to deposition. Understanding Precambrian paleotopography is critical in estimating reservoir thickness and quality. Regional outcrop and borehole mapping of the Mt. Simon in conjunction with mapping seismic reflection data can facilitate the prediction of basement highs. Any potential site must, at the minimum, have seismic reflection data, calibrated with drill-hole information, to evaluate the presence of Precambrian topography and alleviate some of the uncertainty surrounding the thickness or possible absence of the Mt. Simon at a particular sequestration site. The Mt. Simon is thought to commonly overlie Precambrian basement granitic or rhyolitic rocks. In places, at least about 549 m (1800 ft) of topographic relief on the top of the basement surface prior to Mt. Simon deposition was observed. The Mt. Simon reservoir sandstone is thin or not present where basement is topographically high, whereas the low areas can have thick Mt. Simon. The paleotopography on the basement and its correlation to Mt. Simon thickness have been observed at both outcrops and in the subsurface from the states of Illinois, Ohio, Wisconsin, and Missouri. ?? 2009. The American Association of Petroleum Geologists/Division of Environmental Geosciences. All rights reserved.

  16. The time-dependence of compaction localization in a porous sandstone

    Science.gov (United States)

    Heap, M. J.; Brantut, N.; Baud, P.; Meredith, P. G.

    2015-12-01

    Compaction bands in sandstone are laterally-extensive planar deformation features that are characterized by lower porosity and permeability than the surrounding host rock. As a result, this form of localization has important implications for both strain partitioning and fluid flow in the Earth's upper crust. To better understand the time-dependency of compaction band growth, we performed triaxial deformation experiments on water-saturated Bleurswiller sandstone (initial porosity = 0.24) under constant stress (creep) conditions in the compactant regime. Our experiments show that inelastic strain accumulates at a constant stress in the compactant regime, manifest as compaction bands. While creep in the dilatant regime is characterized by an increase in porosity and, ultimately, an acceleration in axial strain rate to shear failure, compaction creep is characterized by a reduction in porosity and a gradual deceleration in axial strain rate. The global decrease in the rates of axial strain, acoustic emission energy, and porosity change during creep compaction is punctuated at intervals by higher rate excursions, interpreted as the formation of compaction bands. The growth rate of compaction bands formed during creep is lower as the applied differential stress, and hence background creep strain rate, is decreased. However, the inelastic strain associated with the growth of a compaction band remains constant over strain rates spanning several orders of magnitude (from 10-8 to 10-5 s-1). We find that, despite the large differences in strain rate and growth rate (from both creep and constant strain rate experiments), the characteristics (geometry, thickness) of the compaction bands remain essentially the same. Several lines of evidence, notably the similarity between the differential stress dependence of creep strain rate in the dilatant and compactant regimes, suggest that, as for dilatant creep, subcritical stress corrosion cracking is the mechanism responsible for

  17. Discordant K-Ar and young exposure dates for the Windjana sandstone, Kimberley, Gale Crater, Mars

    Science.gov (United States)

    Vasconcelos, P. M.; Farley, K. A.; Malespin, C. A.; Mahaffy, P.; Ming, D.; McLennan, S. M.; Hurowitz, J. A.; Rice, Melissa S.

    2016-10-01

    K-Ar and noble gas surface exposure age measurements were carried out on the Windjana sandstone, Kimberley region, Gale Crater, Mars, by using the Sample Analysis at Mars instrument on the Curiosity rover. The sandstone is unusually rich in sanidine, as determined by CheMin X-ray diffraction, contributing to the high K2O concentration of 3.09 ± 0.20 wt % measured by Alpha-Particle X-ray Spectrometer analysis. A sandstone aliquot heated to 915°C yielded a K-Ar age of 627 ± 50 Ma. Reheating this aliquot yielded no additional Ar. A second aliquot heated in the same way yielded a much higher K-Ar age of 1710 ± 110 Ma. These data suggest incomplete Ar extraction from a rock with a K-Ar age older than 1710 Ma. Incomplete extraction at 900°C is not surprising for a rock with a large fraction of K carried by Ar-retentive K-feldspar. Likely, variability in the exact temperature achieved by the sample from run to run, uncertainties in sample mass estimation, and possible mineral fractionation during transport and storage prior to analysis may contribute to these discrepant data. Cosmic ray exposure ages from 3He and 21Ne in the two aliquots are minimum values given the possibility of incomplete extraction. However, the general similarity between the 3He (57 ± 49 and 18 ± 32 Ma, mean 30 Ma) and 21Ne (2 ± 32 and 83 ± 24 Ma, mean 54 Ma) exposure ages provides no evidence for underextraction. The implied erosion rate at the Kimberley location is similar to that reported at the nearby Yellowknife Bay outcrop.

  18. Study of the Effect of Clay Particles on Low Salinity Water Injection in Sandstone Reservoirs

    Directory of Open Access Journals (Sweden)

    Sina Rezaei Gomari

    2017-03-01

    Full Text Available The need for optimal recovery of crude oil from sandstone and carbonate reservoirs around the world has never been greater for the petroleum industry. Water-flooding has been applied to the supplement primary depletion process or as a separate secondary recovery method. Low salinity water injection is a relatively new method that involves injecting low salinity brines at high pressure similar to conventional water-flooding techniques, in order to recover crude oil. The effectiveness of low salinity water injection in sandstone reservoirs depends on a number of parameters such as reservoir temperature, pressure, type of clay particle and salinity of injected brine. Clay particles present on reservoir rock surfaces adsorb polar components of oil and modify wettability of sandstone rocks to the oil-wet state, which is accountable for the reduced recovery rates by conventional water-flooding. The extent of wettability alteration caused by three low salinity brines on oil-wet sandstone samples containing varying clay content (15% or 30% and type of clay (kaolinite/montmorillonite were analyzed in the laboratory experiment. Contact angles of mica powder and clay mixture (kaolinite/montmorillonite modified with crude oil were measured before and after injection with three low salinity sodium chloride brines. The effect of temperature was also analyzed for each sample. The results of the experiment indicate that samples with kaolinite clay tend to produce higher contact angles than samples with montmorillonite clay when modified with crude oil. The highest degree or extent of wettability alteration from oil-wet to intermediate-wet state upon injection with low salinity brines was observed for samples injected with brine having salinity concentration of 2000 ppm. The increase in temperature tends to produce contact angles values lying in the higher end of the intermediate-wet range (75°–115° for samples treated at 50 °C, while their corresponding

  19. Nitrate levels and the age of groundwater from the Upper Devonian sandstone aquifer in Fife, Scotland.

    Science.gov (United States)

    McNeill, G W; Anderson, J; Elliot, T

    2003-03-01

    The tritium concentrations in 13 groundwater samples from boreholes throughout the Upper Devonian sandstone aquifer of Fife have been measured. Due to atmospheric variations in tritium concentrations over the last century, this radioactive tracer can be used as a groundwater age indicator. In this study, the groundwater tritium concentrations have allowed for the area to be divided into three zones, and the variable chemistry of the groundwater samples, including the problem of recent elevated nitrate levels in the Fife Aquifer, has been interpreted in terms of their relative ages.

  20. Wettability Behavior of Crude Oil-Silica Nanofluids-Sandstone Systems

    Science.gov (United States)

    Bai, Lingyun; Li, Chunyan; Pales, Ashley; Huibers, Britta; Ladner, David; Daigle, Hugh; Darnault, Christophe

    2016-04-01

    Mobilizing and recovering crude oils from geological formations is critical for the management and exploitation of petroleum reservoirs. Nanoparticles, with their unique physico-chemical properties can increase the efficiency of enhanced oil recovery (EOR) by decreasing interfacial tension (IFT) between the oil and aqueous phase systems, and altering rock wettability. Our research examines the potential use of nanoparticles as a means of EOR by studying the influence of silicon oxide (SIO2) nanoparticles on the wettability and interfacial tension of different crude oil-silica nanofluids-sandstone systems. We designed nanofluid treatments to manipulate changes in wettability of Berea and Boise sandstones simulating petroleum reservoir. Experiments were performed to measure the IFT and wettability involving different concentrations of nanoparticles with and without the addition of surfactant to determine which nanofluids produced the most favorable wettability changes for optimal EOR with light crude oil (e.g., West Texas, API: 40), medium crude oil (Prudhoe Bay, API: 28), and heavy crude oil (e.g., Lloydminster, API: 20). We investigated the addition of Tween 20 nonionic surfactant to the nanoparticle dispersions - made from SiO2 nanoparticles - that allows the optimum mobility in porous media through optimization of interfacial tension (IFT) and contact angle, and conducted tests. Batch studies were conducted to measure the IFT and wettability of the nanofluids of different range of nanoparticle concentrations (0-0.1 wt. %) in different reservoir conditions, i.e. brine and brine-surfactant systems made with 5% brine and 2CMC of Tween 20 nonionic surfactants. The dynamic behavior of IFT was monitored using a pendant drop method. Five percent brine-nanoparticle systems containing 0.001 and 0.01 wt.% of nanoparticles resulted in a significant decrease of IFT for light and medium crude oils, while the highest decrease of IFT for heavy crude oil was observed with 0.1 wt

  1. Stone temperature and moisture variability under temperate environmental conditions: Implications for sandstone weathering

    Science.gov (United States)

    McAllister, Daniel; Warke, Patricia; McCabe, Stephen

    2017-03-01

    Temperature and moisture conditions are key drivers of stone weathering processes in both natural and built environments. Given their importance in the breakdown of stone, a detailed understanding of their temporal and spatial variability is central to understanding present-day weathering behaviour and for predicting how climate change may influence the nature and rates of future stone decay. Subsurface temperature and moisture data are reported from quarry fresh Peakmoor Sandstone samples exposed during summer (June-July) and late autumn/early winter (October-December) in a mid-latitude, temperate maritime environment. These data demonstrate that the subsurface thermal response of sandstone comprises numerous short-term (minutes), low magnitude fluctuations superimposed upon larger-scale diurnal heating and cooling cycles with distinct aspect-related differences. The short-term fluctuations create conditions in the outer 5-10 mm of stone that are much more 'energetic' in comparison to the more subdued thermal cycling that occurs deeper within the sandstone samples. Data show that moisture dynamics are equally complex with a near-surface region (5-10 mm) in which frequent moisture cycling takes place and this, combined with the thermal dynamism exhibited by the same region, may have significant implications for the nature and rate of weathering activity. Data indicate that moisture input from rainfall, particularly when it is wind-driven, can travel deep into the stone where it can prolong the time of wetness. This most often occurs during wetter winter months when moisture input is high and evaporative loss is low but can happen at any time during the year when the hydraulic connection between near-surface and deeper regions of the stone is disrupted with subsequent loss of moisture from depth slowing as it becomes reliant on vapour diffusion alone. These data illustrate the complexity of temperature and moisture conditions in sandstone exposed to the 'moderate

  2. Geochemical characteristics of Dongsheng sandstone-type uranium deposit, Ordos Basin

    Institute of Scientific and Technical Information of China (English)

    SUN Yuzhuang; LIU Chiyang; DAI Shifeng; QIN Peng

    2007-01-01

    Generally, sandstone-type uranium deposits can be divided into three zones according to their redox conditions: oxidized zone, ore zone and reduced zone. The Dongsheng uranium deposit belongs to this type. In order to study its geochemical characteristics, 11 samples were taken from the three zones of the Dongsheng uranium deposit. Five samples of them were collected from the oxidized zone, four samples from the ore zone and two samples from the reduced zone. These samples were analyzed using organic and inorganic geochemical methods. The results of GC traces and ICP-MASS indicate that the three zones show different organic and inorganic geochemical characteristics.

  3. New well architectures assessment for geothermal exploitation of the Triassic sandstones in Paris basin

    OpenAIRE

    Hamm, Virginie; Bouzit, Madjid; Lopez, Simon

    2016-01-01

    International audience; The deep geothermal resource of the center of the Paris basin (Ile-de-France, France) has been exploited since the mid-1980s, the main target being the Dogger limestone aquifer (1,500–2,000 m deep, 55–80°C). Currently, the Triassic sandstone units below the Dogger aquifer are envisaged as new targets. This paper presents a modelling and economic analysis used to assess new well architectures (sub-horizontal, horizontal or multilateral wells) in comparison with standard...

  4. Giant stromatolites and a supersurface in the Navajo Sandstone, Capitol Reef National Park, Utah

    Science.gov (United States)

    Eisenberg, Len

    2003-02-01

    At Capitol Reef National Park, Utah, 5-m-high stromatolites are present locally on interdune carbonate lenses in the Early Jurassic Navajo Sandstone. The stromatolites display both finely laminated and fenestral internal fabrics, and grew along south-facing interdune margins. These stromatolites formed during a high-water-table episode engendered by a dune-dammed paleodrainage in a stabilized Navajo erg. These stromatolites, and the thick interdune section associated with them, suggest a hiatus in erg accumulation and the presence of a super bounding surface.

  5. Active member bridge feedback control for damping augmentation

    Science.gov (United States)

    Chen, Gun-Shing; Lurie, Boris J.

    1992-01-01

    An active damping augmentation approach using active members in a structural system is described. The problem of maximizing the vibration damping in a lightly damped structural system is considered using the analogy of impedance matching between the load and source impedances in an electrical network. The proposed active damping augmentation approach therefore consists of finding the desired active member impedances that maximize the vibration damping, and designing a feedback control in order to achieve desired active member impedances. This study uses a bridge feedback concept that feeds back a combination of signals from sensors of the axial force and relative velocity across the active member to realize the desired active member impedance. The proposed active damping augmentation approach and bridge feedback concept were demonstrated on a three-longeron softly suspended truss structure.

  6. Relationships between stylolites and cementation in sandstone reservoirs: Examples from the North Sea, U.K. and East Greenland

    Science.gov (United States)

    Baron, Martin; Parnell, John

    2007-01-01

    The reservoir potential of hydrocarbon sandstone reservoirs may be significantly reduced by compartmentation as a result of the development of stylolites. A petrographic and fluid inclusion microthermometric study was performed on sandstones containing abundant stylolites from the Buchan, Galley and Scott Fields in the Outer Moray Firth, offshore Scotland, and from a palaeo-oil bearing sequence in East Greenland. The main objective of this study was to further constrain the temperatures and burial depths at which stylolitization occurs in sandstone reservoirs. The sandstones containing abundant stylolites are also characterized by their highly cemented nature. Numerous occurrences of quartz overgrowths clearly truncated by sutured stylolites are evident in all of the samples. Fluid inclusion microthermometry reveals that quartz cementation, which is interpreted to be coeval with stylolitization, occurred at minimum temperatures of between 86 and 136 °C. Basin modelling of the Scott and Galley Fields indicates that quartz cementation and stylolite development formed at depths greater than 2.5 km which were attained during rapid Tertiary burial. The occurrence of hydrocarbon fluid inclusions within healed microfractures orientated at high angles to the stylolites suggests that these microfractures provided pathways for hydrocarbon migration in the highly cemented, low permeability zones associated with highly stylolitized sandstones.

  7. Study of Hydrogen and Oxygen and Its Reaction With Host Elements in Sandstone by Laser-Induced Breakdown Spectroscopy (LIBS)

    Science.gov (United States)

    Suyanto, Hery

    2017-05-01

    A study of hydrogen and oxygen and its reaction with host elements in a sandstone has been done by laser-induced breakdown spectroscopy (LIBS). The sandstone was irradiated by Nd-YAG laser (1064 nm, 7 ns) with varied energy of 60 mJ till 140 mJ in surrounding air gas pressure of 1 atm and produced plasma. The emission intensities of hydrogen H I 656.2 nm and oxygen O I 777.2 nm in the plasma were captured by HR 2500+ spectrometer and displayed in intensity as a function of wavelength. The data show that the emission intensities of hydrogen and oxygen increase with increasing laser energy at a gradient of 5.4 and 11.8 respectively every increasing laser energy of 20 mJ. To characterize the reaction process between hydrogen and oxygen with the host elements of the sandstone, a 0.2 ml demineralized water was dropped on the sandstone surface and was analyzed as a function of delay time reaction and temperature. The data show that the oxidation reaction between host elements and oxygen occurred after 25 minutes that the oxygen emission intensity increases and the hydrogen emission intensity decreases. Another data also show that the increasing temperature of sandstone until 80 C increased intermolecular bond between oxygen and host element and dehydrogenation took place after reaching this temperature

  8. Study of adsorption Ag and Pb in liquid sample using Berea sandstone by commercial laser-induced breakdown spectroscopy (LIBS)

    Science.gov (United States)

    Suyanto, H.; Wendri, N.; Agustiningrum, U.; Manurung, M.

    2016-11-01

    Qualitative and quantitative analysis of Pb and Ag elements in liquid samples had been done by commercial laser-induced breakdown spectroscopy (LIBS) using adsorption method on a Berea Sandstone. The aim of this study is to identify the thickness of the Berea Sandstone for adsorbing Pb and Ag elements in liquid. The experiment was started with characterizing the Berea Sandstone that contains Si, Na, H, Li, K, Ca, O, N, Be, Ti, Al, Mg and Ba. Some of these elements have ability to adsorb Pb and Ag elements in the liquid. To prove this phenomenon, it is required to look for the experiment parameter optimum conditions such as laser energy, adsorption time and sample temperature. The experiment was conducted by dropping 2 ml standard liquid containing 1000 ppm of Pb and Ag to the Berea Sandstone surface. The result showed that the parameter optimum conditions for analyzing Pb and Ag elements in liquid sample with adsorption method were adsorption delay-time of 15 minutes, laser energy of 120 mJ and sample heating of 80 °C. The next experiment was focused on the number of adsorption as a function of depth. The data showed that Pb and Ag elements in liquid sample of 2 ml, 1000 ppm were fully adsorbed by the Berea Sandstone until the depth of 0.372 mm and 10.40 mm from the surface, respectively. The data also showed that the limit of detection predicted to about 22.76 ppm.

  9. Effect of water saturation and temperature in the range of 193 to 373 K on the thermal conductivity of sandstone

    Science.gov (United States)

    Guo, P. Y.; Zhang, N.; He, M. C.; Bai, B. H.

    2017-03-01

    The thermal conductivity of porous media is crucial for many geological and engineering projects. Although the thermal conductivity at low temperatures is often overlooked, it is of great significance to calculate the amount of heat that the ice sheet absorbs from the Earth. In this study, the thermal conductivity of dry and water-saturated sandstone was measured in the temperature range of 193 to 373 K using a transient hot wire method. All samples were collected from East China, with a sample porosity distribution of 5 to 13%. The effects of temperature, water saturation and phase transition of fluid in the pores were investigated. The results indicate that the thermal conductivity decreases with an increase in temperature and that the decrease is steeper when the temperature is below 273 K. Moreover, it is found that the thermal conductivity of the saturated sandstone is larger than that of the dry sandstone. With an increase in porosity, the thermal conductivity significantly increases in saturated sandstone but remains almost the same or even decreases in dry sandstones. Finally, it is revealed that the effect of phase transformation on the thermal conductivity is significant. When the water in pores becomes ice, the thermal conductivity increases significantly and increases further as the temperature decreases.

  10. Microfabric and anisotropy of elastic waves in sandstone - An observation using high-resolution X-ray microtomography

    Science.gov (United States)

    Kahl, Wolf-Achim; Hinkes, Robert; Feeser, Volker; Holzheid, Astrid

    2013-04-01

    Petrophysical experiments, using acoustic velocities to characterise anisotropies of mechanical behaviour of rocks are of essential relevance to understand the geomechanical behaviour of sandstone reservoirs under changing stress fields. Here, we present high-resolution X-ray microtomography (μ-CT) as a supplementary research tool to interpret anisotropic ultrasound velocities in sandstones with variation of isotopic stress. Specimens of two Lower Cretaceous sandstones (localities Bentheim and Obernkirchen, both Germany) have been used in petrophysical laboratory experiments under dry conditions to study ultrasonic sound velocities (frequency of signal input 1 MHz). Subsequently, oriented micro-plugs drilled from the sandstone samples were investigated using high-resolution X-ray microtomography. By means of image processing of the reconstructed scan images, geometric attributes such as mean structural thickness, orientation and tortuosity were evaluated from the μ-CT data for both pore space and grain skeleton. Our observations clearly indicate the different roles of pore space and grain skeleton in regard to the propagation of ultrasonic waves: because the pores do not transmit the waves, it was sufficient to investigate the average thickness of this fabric element. In contrast, as the ultrasonic waves traverse the rock via the adjacent grains, it was necessary to survey the actual travel lengths of seismic waves in the sandstone grain skeleton.

  11. Strength Anisotropy of Berea Sandstone: Results of X-Ray Computed Tomography, Compression Tests, and Discrete Modeling

    Science.gov (United States)

    Kim, Kwang Yeom; Zhuang, Li; Yang, Hwayoung; Kim, Hanna; Min, Ki-Bok

    2016-04-01

    Berea sandstone in northern Ohio is a transversely isotropic rock. X-ray CT investigations showed that its internal structure is composed of cross-bedded loose layers and relatively thin tightly packed layers called bedding. Uniaxial compression tests were performed on different Berea sandstone specimens. The uniaxial compressive strength (UCS) decreases with increasing porosity, and also decreases with increasing inclination of the bedding plane relative to horizontal line. Two-dimensional discrete modeling was applied to investigate the micromechanical behavior of Berea sandstone. Different microparameters were assigned to loose and tight layers. The UCS simulation results agree well with the experimental results. At the peak stress, cracks almost always develop in loose layers regardless of the bedding plane orientation. In addition, both normal and shear cracks occur earlier for specimens with a higher inclination angle. No correlations were found between the inclination angle of failure planes and the orientation of bedding planes. The bedding planes of Berea sandstone are not weak planes. The strength anisotropy of Berea sandstone is not significant compared with other rocks such as shale, gneiss, and schist.

  12. Effective healthcare teams require effective team members: defining teamwork competencies

    OpenAIRE

    Leggat Sandra G

    2007-01-01

    Abstract Background Although effective teamwork has been consistently identified as a requirement for enhanced clinical outcomes in the provision of healthcare, there is limited knowledge of what makes health professionals effective team members, and even less information on how to develop skills for teamwork. This study identified critical teamwork competencies for health service managers. Methods Members of a state branch of the professional association of Australian health service managers...

  13. 17 CFR 190.09 - Member property.

    Science.gov (United States)

    2010-04-01

    ... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Member property. 190.09... Member property. (a) Member property. “Member property” means, in connection with a clearing organization bankruptcy, the property which may be used to pay that portion of the net equity claim of a member which...

  14. Contrasting styles of large-scale displacement of unconsolidated sand: examples from the early Jurassic Navajo Sandstone on the Colorado Plateau, USA

    Science.gov (United States)

    Bryant, Gerald

    2015-04-01

    Large-scale soft-sediment deformation features in the Navajo Sandstone have been a topic of interest for nearly 40 years, ever since they were first explored as a criterion for discriminating between marine and continental processes in the depositional environment. For much of this time, evidence for large-scale sediment displacements was commonly attributed to processes of mass wasting. That is, gravity-driven movements of surficial sand. These slope failures were attributed to the inherent susceptibility of dune sand responding to environmental triggers such as earthquakes, floods, impacts, and the differential loading associated with dune topography. During the last decade, a new wave of research is focusing on the event significance of deformation features in more detail, revealing a broad diversity of large-scale deformation morphologies. This research has led to a better appreciation of subsurface dynamics in the early Jurassic deformation events recorded in the Navajo Sandstone, including the important role of intrastratal sediment flow. This report documents two illustrative examples of large-scale sediment displacements represented in extensive outcrops of the Navajo Sandstone along the Utah/Arizona border. Architectural relationships in these outcrops provide definitive constraints that enable the recognition of a large-scale sediment outflow, at one location, and an equally large-scale subsurface flow at the other. At both sites, evidence for associated processes of liquefaction appear at depths of at least 40 m below the original depositional surface, which is nearly an order of magnitude greater than has commonly been reported from modern settings. The surficial, mass flow feature displays attributes that are consistent with much smaller-scale sediment eruptions (sand volcanoes) that are often documented from modern earthquake zones, including the development of hydraulic pressure from localized, subsurface liquefaction and the subsequent escape of

  15. Deformation of Aztec Sandstone at Valley of Fire of Nevada: failure modes, sequence of deformation, structural products and their interplay with paleo fluids

    Science.gov (United States)

    Aydin, A.

    2014-12-01

    The Valley of Fire State Park, 60 km NE of Las Vegas, is a beacon of knowledge for deformation of Aztec Sandstone, a cross-bedded quartz arenite deposited in the Aztec-Navajo-Nugget erg in early Jurassic. It displays great diversity of physical properties, different localization types and micromechanics. The two deformation episodes, the Sevier folding & thrusting and the Basin & Range extension affected the area. The appearance of compaction bands marks the earliest deformation structure and their distribution, orientation, and dimension are controlled by the depositional architecture and loading. The earliest shear structures in the area are the Muddy Mountain, Summit, and Willow Tank thrusts and numerous small-scale bed-parallel faults. They altogether produced several kilometers of E-SE transport and shortening in the late Cretaceous and display numerous shear bands in its damage zone within the Aztec Sandstone. Shear bands also occur along dune boundaries and cross-bed interfaces. These observations indicate that the early deformation of the sandstone was accommodated by strain localization with various kinematics. The younger generation of faults in the area is of mid-Miocene age, and crops out pervasively. It includes a series of small offset normal faults (less than a few ten meters) which can be identified at steep cliff faces. These faults are highly segmented and are surrounded by a dense population of splay fractures. A large number of these splays were later sheared sequentially resulting in a well-defined network of left- and right-lateral strike-slip faults with slip magnitudes up to a few kilometers in the Park. The formation mechanisms of both the normal and strike-slip faults can be characterized as the sliding along planes of initial weaknesses and the accompanying cataclastic deformation. Some of the initial weak planes are associated with the depositional elements such as interdune boundaries and cross-bed interfaces while others are joint

  16. 1st paleomagnetic investigation of Nubia Sandstone at Kalabsha, south Western Desert of Egypt

    Science.gov (United States)

    Mostafa, R.; Khashaba, A.; El-Hemaly, I. A.; Takla, E. M.; Abdel Aal, E.; Odah, H.

    2016-06-01

    Two profiles have been sampled from the Nubia Sandstone at Aswan, south Western Desert: the 1st profile has been taken from Abu Aggag Formation and the 2nd one was from Sabaya Formation (23.25 °N, 32.75 °E). 136 oriented cores (from 9 sites) have been sampled. Abu Aggag Formation is of Late Cretaceous (Turonian) and Sabaya Formation is of early Cretaceous (Albian-Cenomanian). The studied rocks are subjected to rock magnetic measurements as well as demagnetization treatment. It has been found that hematite is the main magnetic mineral in both formations. Four profile sections from Abu Aggag Formation, yielded a magnetic component with D = 352.7°, I = 36.6° with α95 = 5.2° and the corresponding pole lies at Lat. = 82.8 °N and Long. = 283.1 °E. Five profile sections from Sabaya Formation, yielded a magnetic component with D = 348.6°, I = 33.3° with α95 = 5.8° and the corresponding pole lies at Lat. = 78.3 °N and Long. = 280.4 °E. The obtained paleopole for the two formations lies at Lat. = 80.5 °N and Long. = 281.7 °E. The obtaind magnetic components are considered primary and the corresponding paleopole reflects the age of Nubia Sandstone when compared with the previously obtained Cretaceous poles for Egypt.

  17. Performance of Surfactant Methyl Ester Sulphonate solution for Oil Well Stimulation in reservoir sandstone TJ Field

    Science.gov (United States)

    Eris, F. R.; Hambali, E.; Suryani, A.; Permadi, P.

    2017-05-01

    Asphaltene, paraffin, wax and sludge deposition, emulsion and water blocking are kinds ofprocess that results in a reduction of the fluid flow from the reservoir into formation which causes a decrease of oil wells productivity. Oil well Stimulation can be used as an alternative to solve oil well problems. Oil well stimulation technique requires applying of surfactant. Sodium Methyl Ester Sulphonate (SMES) of palm oil is an anionic surfactant derived from renewable natural resource that environmental friendly is one of potential surfactant types that can be used in oil well stimulation. This study was aimed at formulation SMES as well stimulation agent that can identify phase transitions to phase behavior in a brine-surfactant-oil system and altered the wettability of rock sandstone and limestone. Performance of SMES solution tested by thermal stability test, phase behavioral examination and rocks wettability test. The results showed that SMES solution (SMES 5% + xylene 5% in the diesel with addition of 1% NaCl at TJformation water and SMES 5% + xylene 5% in methyl ester with the addition of NaCl 1% in the TJ formation water) are surfactant that can maintain thermal stability, can mostly altered the wettability toward water-wet in sandstone reservoir, TJ Field.

  18. Mixed fluvial systems of Messak Sandstone, a deposit of Nubian lithofacies, southwestern Libya

    Energy Technology Data Exchange (ETDEWEB)

    Lorenz, J.C.

    1987-05-01

    The Messak Sandstone is a coarse to pebbly, tabular cross-bedded, Lower Cretaceous deposit of the widespread Nubian lithofacies. It was deposited at the northern edge of the Murzuq basin in southwestern Libya. Although the sedimentary record is predominantly one of braided fluvial systems, a common subfacies within the formation is interpreted to record the passage of straight-crested sand waves across laterally migrating point bars in sinuous rivers, similar to the pattern documented by Singh and Kumar on the modern Ganga and Yamuna Rivers. Because the sand waves were larger on the lower parts of the point bars, lateral migration created diagnostic thinning-upward, unidirectional cosets of tabular cross-beds as well as fining-upward, grain-size trends. Common, thick, interbedded claystones, deposited in associated paludal and lacustrine environments, and high variance in cross-bed dispersion patterns also suggest the local presence of sinuous fluvial systems within the overall braided regime. The Messak Sandstone contains some of the features that led Harms et al to propose an unconventional low-sinuosity fluvial environment for the Nubian lithofacies in Egypt, and the continuously high water levels of this model may explain channel-scale clay drapes and overturned cross-beds in the Messak. However, most of the Messak characteristics are incompatible with the low-sinuosity model, suggesting instead that the fluvial channels in the Murzuq basin alternated between braided and high-sinuosity patterns.

  19. Behaviour of layered sandstone under Brazilian test conditions:Layer orientation and shape effects

    Institute of Scientific and Technical Information of China (English)

    Abbass Tavallali; André Vervoort

    2013-01-01

    The experimental study in this paper focuses on the effects of the layer orientation and sample shape on failure strength and fracture pattern of samples tested under Brazilian test conditions (i.e. diametrical loading of cylindrical discs) for one particular layered sandstone which is from Modave in the south of Belgium. The variations of the strength in combination with the failure patterns are examined as a function of the inclination angle between the layer plane and the loading direction. The experimental, results clearly show that the induced fracture patterns are a combination of tensile and/or shear fractures. In shape effect experiments the layer thickness and the number of layer boundaries are investigated. Different blocks of Modave sandstone are used to prepare samples. The layer thickness is different among the various blocks, but the layer thickness in each studied rock block can be considered to be constant;hence, the number of layer boundaries changes according to the sample diameter for samples of the same block. The experimental study shows that the layer thickness plays a more important role than the number of layer boundaries per sample.

  20. Provenance of upper Triassic sandstone, southwest Iberia (Alentejo and Algarve basins): tracing variability in the sources

    Science.gov (United States)

    Pereira, M. F.; Ribeiro, C.; Gama, C.; Drost, K.; Chichorro, M.; Vilallonga, F.; Hofmann, M.; Linnemann, U.

    2016-01-01

    Laser ablation ICP-MS U-Pb analyses have been conducted on detrital zircon of Upper Triassic sandstone from the Alentejo and Algarve basins in southwest Iberia. The predominance of Neoproterozoic, Devonian, Paleoproterozoic and Carboniferous detrital zircon ages confirms previous studies that indicate the locus of the sediment source of the late Triassic Alentejo Basin in the pre-Mesozoic basement of the South Portuguese and Ossa-Morena zones. Suitable sources for the Upper Triassic Algarve sandstone are the Upper Devonian-Lower Carboniferous of the South Portuguese Zone (Phyllite-Quartzite and Tercenas formations) and the Meguma Terrane (present-day in Nova Scotia). Spatial variations of the sediment sources of both Upper Triassic basins suggest a more complex history of drainage than previously documented involving other source rocks located outside present-day Iberia. The two Triassic basins were isolated from each other with the detrital transport being controlled by two independent drainage systems. This study is important for the reconstruction of the late Triassic paleogeography in a place where, later, the opening of the Central Atlantic Ocean took place separating Europe from North America.

  1. Linear and nonlinear modulus surfaces in stress space, from stress-strain measurements on Berea sandstone

    Directory of Open Access Journals (Sweden)

    M. Boudjema

    2003-01-01

    Full Text Available The elastic response of many rocks to quasistatic stress changes is highly nonlinear and hysteretic, displaying discrete memory. Rocks also display unusual nonlinear response to dynamic stress changes. A model to describe the elastic behavior of rocks and other consolidated materials is called the Preisach-Mayergoyz (PM space model. In contrast to the traditional analytic approach to stress-strain, the PM space picture establishes a relationship between the quasistatic data and a number density of hysteretic mesoscopic elastic elements in the rock. The number density allows us to make quantitative predictions of dynamic elastic properties. Using the PM space model, we analyze a complex suite of quasistatic stress-strain data taken on Berea sandstone. We predict a dynamic bulk modulus and a dynamic shear modulus surface as a function of mean stress and shear stress. Our predictions for the dynamic moduli compare favorably to moduli derived from time of flight measurements. We derive a set of nonlinear elastic constants and a set of constants that describe the hysteretic behavior of the sandstone.

  2. Characteristics of Chang 21 Low Permeability Sandstone Reservoir in Shunning Oil Field

    Institute of Scientific and Technical Information of China (English)

    WANG Jian-min; YU Liu-ying

    2006-01-01

    Characteristics of Chang 21 low permeability sandstone reservoir of Shunning oil field are analyzed and evaluated based on the data of well logging and experiment. The result shows that 1) the Chang 21 low permeability reservoir belongs to the classification of middle-to-fine sized feldspar sandstone, with its components being low in maturity, deposited in distributary rivers in the front of the delta; 2) the reservoir is obviously dominated by a low or a very low permeability with a linear variation tendency different from that of the ultra-low permeability reservoir; 3) the spatial variation in lithology and physical properties of the reservoir are controlled by the sedimentary facies zones, and 4)the physical property of the reservoir is significantly influenced by clastic constituents and their structure, and the constituent of cement materials and their content. The result also shows that the diagenesis action of the reservoir is quite strong in which dissolution greatly modified the reservoir In addition, the inter-granular dissolved pores are the mainly developed ones and the micro-structure is dominated by the combination of middle-to-large sized pores with fine-to-coarse throats. Finally, the radius of the throats is in good exponential correlation with permeability and the seepage capacity comes from those large sized throats.

  3. Experimental investigation on the energy evolution of dry and water-saturated red sandstones

    Institute of Scientific and Technical Information of China (English)

    Zhang Zhizhen; Gao Feng

    2015-01-01

    In order to investigate the effect of water content on the energy evolution of red sandstone, the axial loading–unloading experiments on dry and water-saturated sandstone samples were conducted, and the distribution and evolution of elastic energy and dissipated energy within the rock were measured. The results show that the saturation process from dry to fully-saturated states reduces the strength, rigid-ity and brittleness of the rock by 30.2%, 25.5%and 16.7%, respectively. The water-saturated sample has larger irreversible deformation in the pre-peak stage and smaller stress drop in the post-peak stage. The saturation process decreases the accumulation energy limit by 38.9%, but increases the dissipated energy and residual elastic energy density, thus greatly reducing the magnitude and rate of energy release. The water-saturated sample has lower conversion efficiency to elastic energy by 3%in the pre-peak region; moreover, the elastic energy ratio falls with a smaller range in the post-peak stage. Therefore, saturation process can greatly reduce the risk of dynamic disaster, and heterogeneous water content can lead to dynamic disaster possibly on the other hand.

  4. Evaluation and prevention of formation damage in offshore sandstone reservoirs in China

    Institute of Scientific and Technical Information of China (English)

    Yang Shenglai; Sheng Zhichao; Liu Wenhui; Song Zhixue; Wu Ming; Zhang Jianwei

    2008-01-01

    Reduction in water injectivity would be harmful to the waterflood development of offshore sandstone oil reservoirs. In this paper the magnitude of formation damage during water injection was evaluated by analyzing the performance of water injection in the Bohai offshore oilfield, China. Two parameters, permeability reduction and rate of wellhead pressure rise, were proposed to evaluate the formation damage around injection wells. The pressure performance curve could be divided into three stages with different characteristics. Analysis of field data shows that formation damage caused by water injection was severe in some wells in the Bohai offshore oilfield, China. In the laboratory, the content of clay minerals in reservoir rock was analyzed and sensitivity tests (including sensitivity to water,flow rate, alkali, salt and acid) were also conducted. Experimental results show that the reservoir had a strong to medium sensitivity to water (i.e. clay swelling) and a strong to medium sensitivity to flow rate,which may cause formation damage. For formation damage prevention, three injection schemes of clay stabilizer (CS) were studied, i.e. continuous injection of low concentration CS (Ci), slug injection of high concentration CS (SI), and slug injection of high concentration CS followed by continuous injection of low concentration CS (SI-CI). Core flooding experiments show that SI-CI is an effective scheme to prevent formation damage and is recommended for the sandstone oil reservoirs in the Bohai offshore oilfield during water injection.

  5. Integrated geologic and engineering reservoir characterization of the Hutton Sandstone, Jackson region, Australia

    Energy Technology Data Exchange (ETDEWEB)

    Hamilton, D.S.; Holtz, M.H.; Yeh, J. [Univ. of Texas, Austin, TX (United States)] [and others

    1996-08-01

    An integrated geologic and engineering reservoir characterization study of the Hutton Sandstone was completed for the Jackson region, Eromanga Basin, Australia. Our approach involves four principal steps: (1) determine reservoir architecture within a high-resolution sequence stratigraphic framework, (2) investigate trends in reservoir fluid flow, (3) integrate fluid flow trends with reservoir architecture to identify fundamental reservoir heterogeneities, and (4) identify opportunities for reserve growth. Contrary to the existing perception, the Hutton Sandstone, a continental-scale bed-load fluvial system, does not behave as a large, homogeneous tank in which pistonlike displacement of produced oil occurs unimpeded by vertical migration of the aquifer. The sequence stratigraphic analysis identified numerous thin but widespread shale units, deposited during lacustrine flooding events that periodically interrupted episodes of coarse clastic Hutton deposition. These shales represent chronostratigraphically significant surfaces. More importantly, the trends established in reservoir fluid flow from monitoring aquifer encroachment, production response to water shut-off workovers, and differential depletion in Repeat Formation Tests indicate that these shale units act as efficient barriers to vertical fluid flow. Erosion of the upper part of the Hutton reservoir by the younger Birkhead mixed-load fluvial system caused further stratigraphic complexity and introduced additional barriers to vertical and lateral migration of mobile oil and aquifer encroachment. This integrated characterization targeted strategic infill and step-out drilling and recompletion candidates.

  6. Fragmentation characteristics analysis of sandstone fragments based on impact rockburst test

    Directory of Open Access Journals (Sweden)

    Dongqiao Liu

    2014-06-01

    Full Text Available Impact rockburst test on sandstone samples with a central hole is carried out under true triaxial static loads and vertical dynamic load conditions, and rock fragments after the test are collected. The fragments of sandstone generated from strain rockburst test and uniaxial compression test are also collected. The fragments are weighed and the length, width and thickness of each piece of fragments are measured respectively. The fragment quantities with coarse, medium, fine and micro grains in different size ranges, mass and particles distributions are also analyzed. Then, the fractal dimension of fragments is calculated by the methods of size-frequency, mass-frequency and length-to-thickness ratio-frequency. It is found that the crushing degree of impact rockburst fragments is higher, accompanied with blocky characteristics observably. The mass percentage of small grains, including fine and micro grains, in impact rockburst test is higher than those in strain rockburst test and uniaxial compression test. Energy dissipation from rockburst tests is more than that from uniaxial compression test, as the quantity of micro grains generated does.

  7. Geochemical discriminations of sandstones from the Mohe Foreland basin, northeastern China: Tectonic setting and provenance

    Institute of Scientific and Technical Information of China (English)

    HE Zhengjun; LI Jinyi; MO Shenguo; Andrey A. Sorokin

    2005-01-01

    Discrimination of sandstone geochemistry to tectonic settings and provenance has become an effective method in the studies of complex geological circumstances because of its higher sensitivity for the stability of tectonic settings in the period of basin deposition. Results of geochemical analyses in this paper show that sandstone samples of the Mesozoic Mohe basin fall in active continental margin settings on several kinds of tectonic discriminatory diagrams (Bhatia et al. 1983, 1986; Roser et al. 1986,1988,1999). The samples are also characterized by binary-system provenances, whose terrigenous clastic materials mainly derived from the orogenic belt near the basin to the north and secondarily from the continental region in the south of the basin at the same time. The research results of rock geochemistry, combined with tectonic analysis, reflect that tectonic type of the basin is a foreland basin with nature of depositional accumulation of molass, but not continental rift basin considered in the past. This finding provides important evidence of rock geochemistry for the original structural linkage between the Mohe Foreland Basin and Mongol-Okhotsk Orogen in Mesozoic.

  8. Reservoir heterogeneity in carboniferous sandstone of the Black Warrior basin. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kugler, R.L.; Pashin, J.C.; Carroll, R.E.; Irvin, G.D.; Moore, H.E.

    1994-06-01

    Although oil production in the Black Warrior basin of Alabama is declining, additional oil may be produced through improved recovery strategies, such as waterflooding, chemical injection, strategic well placement, and infill drilling. High-quality characterization of reservoirs in the Black Warrior basin is necessary to utilize advanced technology to recover additional oil and to avoid premature abandonment of fields. This report documents controls on the distribution and producibility of oil from heterogeneous Carboniferous reservoirs in the Black Warrior basin of Alabama. The first part of the report summarizes the structural and depositional evolution of the Black Warrior basin and establishes the geochemical characteristics of hydrocarbon source rocks and oil in the basin. This second part characterizes facies heterogeneity and petrologic and petrophysical properties of Carter and Millerella sandstone reservoirs. This is followed by a summary of oil production in the Black Warrior basin and an evaluation of seven improved-recovery projects in Alabama. In the final part, controls on the producibility of oil from sandstone reservoirs are discussed in terms of a scale-dependent heterogeneity classification.

  9. NMR Pore Structure and Dynamic Characteristics of Sandstone Caused by Ambient Freeze-Thaw Action

    Directory of Open Access Journals (Sweden)

    Bo Ke

    2017-01-01

    Full Text Available For a deeper understanding of the freeze-thaw weathering effects on the microstructure evolution and deterioration of dynamic mechanical properties of rock, the present paper conducted the nuclear magnetic resonance (NMR tests and impact loading experiments on sandstone under different freeze-thaw cycles. The results of NMR test show that, with the increase of freeze-thaw cycles, the pores expand and pores size tends to be uniform. The experimental results show that the stress-strain curves all go through four stages, namely, densification, elasticity, yielding, and failure. The densification curve is shorter, and the slope of elasticity curve decreases as the freeze-thaw cycles increase. With increasing freeze-thaw cycles, the dynamic peak stress decreases and energy absorption of sandstone increases. The dynamic failure form is an axial splitting failure, and the fragments increase and the size diminishes with increasing freeze-thaw cycles. The higher the porosity is, the more severe the degradation of dynamic characteristics is. An increase model for the relationships between the porosity or energy absorption and freeze-thaw cycles number was built to reveal the increasing trend with the freeze-thaw cycles increase; meanwhile, a decay model was built to predict the dynamic compressive strength degradation of rock after repeated freeze-thaw cycles.

  10. Experimental Study on the Softening Characteristics of Sandstone and Mudstone in Relation to Moisture Content

    Directory of Open Access Journals (Sweden)

    Gui-chen Li

    2017-01-01

    Full Text Available The kinetics of fluid-solid coupling during immersion is an important topic of investigation in rock engineering. Two rock types, sandstone and mudstone, are selected in this work to study the correlation between the softening characteristics of the rocks and moisture content. This is achieved through detailed studies using scanning electron microscopy, shear tests, and evaluation of rock index properties during exposure to different moisture contents. An underground roadway excavation is simulated by dynamic finite element modeling to analyze the effect of moisture content on the stability of the roadway. The results show that moisture content has a significant effect on shear properties reduction of both sandstone and mudstone, which must thus be considered in mining or excavation processes. Specifically, it is found that the number, area, and diameter of micropores, as well as surface porosity, increase with increasing moisture content. Additionally, stress concentration is negatively correlated with moisture content, while the influenced area and vertical displacement are positively correlated with moisture content. These findings may provide useful input for the design of underground roadways.

  11. Reservoir heterogeneity in Carboniferous sandstone of the Black Warrior basin. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kugler, R.L.; Pashin, J.C.; Carroll, R.E.; Irvin, G.D.; Moore, H.E.

    1994-04-01

    Although oil production in the Black Warrior basin of Alabama is declining, additional oil may be produced through improved recovery strategies, such as waterflooding, chemical injection, strategic well placement, and infill drilling. High-quality characterization of reservoirs in the Black Warrior basin is necessary to utilize advanced technology to recover additional oil and to avoid premature abandonment of fields. This report documents controls on the distribution and producibility of oil from heterogeneous Carboniferous reservoirs in the Black Warrior basin of Alabama. The first part of the report summarizes the structural and depositional evolution of the Black Warrior basin and establishes the geochemical characteristics of hydrocarbon source rocks and oil in the basin. This second part characterizes facies heterogeneity and petrologic and petrophysical properties of Carter and Millerella sandstone reservoirs. This is followed by a summary of oil production in the Black Warrior basin and an evaluation of seven improved-recovery projects in Alabama. In the final part, controls on the producibility of oil from sandstone reservoirs are discussed in terms of a scale-dependent heterogeneity classification.

  12. Evaluation of sandstone surface relaxivity using laser-induced breakdown spectroscopy.

    Science.gov (United States)

    Washburn, Kathryn E; Sandor, Magdalena; Cheng, Yuesheng

    2017-02-01

    Nuclear magnetic resonance (NMR) relaxometry is a common technique used to assess the pore size of fluid-filled porous materials in a wide variety of fields. However, the NMR signal itself only provides a relative distribution of pore size. To calculate an absolute pore size distribution from the NMR data, the material's surface relaxivity needs to be known. Here, a method is presented using laser-induced breakdown spectroscopy (LIBS) to evaluate surface relaxivity in sandstones. NMR transverse and longitudinal relaxation was measured on a set of sandstone samples and the surface relaxivity was calculated from the pore size distribution determined with MICP measurements. Using multivariate analysis, it was determined that the LIBS data can predict with good accuracy the longitudinal (R(2)∼0.84) and transverse (R(2)∼0.79) surface relaxivity. Analysis of the regression coefficients shows significant influence from several elements. Some of these are elements previously established to have an effect on surface relaxivity, such as iron and manganese, while others are not commonly associated with surface relaxivity, such as cobalt and titanium. Furthermore, LIBS provides advantages compared to current methods to calibrate surface relaxivity in terms of speed, portability, and sample size requirements. While this paper focuses on geological samples, the method could potentially be expanded to other types of porous materials.

  13. Fragmentation characteristics analysis of sandstone fragments based on impact rockburst test

    Institute of Scientific and Technical Information of China (English)

    Dongqiao Liu; Dejian Li; Fei Zhao; Chengchao Wang

    2014-01-01

    Impact rockburst test on sandstone samples with a central hole is carried out under true triaxial static loads and vertical dynamic load conditions, and rock fragments after the test are collected. The fragments of sandstone generated from strain rockburst test and uniaxial compression test are also collected. The fragments are weighed and the length, width and thickness of each piece of fragments are measured respectively. The fragment quantities with coarse, medium, fine and micro grains in different size ranges, mass and particles distributions are also analyzed. Then, the fractal dimension of fragments is calculated by the methods of size-frequency, mass-frequency and length-to-thickness ratio-frequency. It is found that the crushing degree of impact rockburst fragments is higher, accompanied with blocky character-istics observably. The mass percentage of small grains, including fine and micro grains, in impact rock-burst test is higher than those in strain rockburst test and uniaxial compression test. Energy dissipation from rockburst tests is more than that from uniaxial compression test, as the quantity of micro grains generated does.

  14. Mechanism of formation of wiggly compaction bands in porous sandstone: 1. Observations and conceptual model

    Science.gov (United States)

    Liu, Chun; Pollard, David D.; Deng, Shang; Aydin, Atilla

    2015-12-01

    Field observations are combined with microscopic analyses to investigate the mechanism of formation of wiggly compaction bands (CBs) in the porous Jurassic aeolian Aztec Sandstone exposed at Valley of Fire State Park, Nevada. Among the three types of CBs (T1, T2, and T3), we focused on the wiggly CBs (T3), which show a chevron (T31) or wavy (T32) pattern with typical corner angles of approximately 90° or 130°, respectively. Where corner angles of wiggly CBs increase to 180°, they become straight CBs (T33). Image analyses of thin sections using an optical microscope show host rock porosity increases downslope in this dune, and the predominant type of wiggly CBs also varies from chevron to straight CBs. Specifically, band type varies continuously from chevron to wavy to straight where the porosity and grain sorting of the host rock increase systematically. Based on the crack and anticrack models, we infer that the change from chevron to straight CBs is due to increasing failure angle of the sandstone and this may correlate with increasing grain sorting. Wavy CBs with intermediate failure angle and host rock porosity are an intermediate stage between chevron and straight CBs. Previous sedimentological studies also have suggested that grain size and sorting degree increase downslope on the downwind side of sand dunes due to a sieving process of the wind-blown grains. Therefore, the transition of wiggly CB types in this regard correlates with increasing sorting and perhaps with increasing porosity downslope.

  15. The evolution of faults formed by shearing across joint zones in sandstone

    Science.gov (United States)

    Myers, Rodrick; Aydin, Atilla

    2004-05-01

    The evolution of strike-slip and normal faults formed by slip along joint zones is documented by detailed field studies in the Jurassic Aztec Sandstone in the Valley of Fire State Park, Nevada, USA. Zones of closely spaced planar sub-parallel joints arranged en échelon are sheared, forming faults. Fracturing occurs as a result of shearing, forming new joints. Later shearing along these joints leads to successively formed small faults and newer joints. This process is repeated through many generations of fracturing with increasing fault slip producing a hierarchical array of structures. Strain localization produced by shearing of joint zones at irregularities in joint traces, fracture intersections, and in the span between adjacent sheared joints results in progressive fragmentation of the weakened sandstone, which leads to the formation of gouge along the fault zone. The length and continuity of the gouge and associated slip surfaces is related to the slip magnitude and fault geometry with slip ranging from several millimeters to about 150 m. Distributed damage in a zone surrounding the gouge core is related to the original joint zone configuration (step sense, individual sheared joint overlaps and separation), shear sense, and slip magnitude. Our evolutionary model of fault development helps to explain some outstanding issues concerning complexities in faulting such as, the variability in development of fault rock and fault related fractures, and the failure processes in faults.

  16. Imaging pore space in tight gas sandstone reservoir: insights from broad ion beam cross-sectioning

    Science.gov (United States)

    Desbois, G.; Enzmann, F.; Urai, J. L.; Baerle, C.; Kukla, P. A.; Konstanty, J.

    2010-06-01

    Monetization of tight gas reservoirs, which contain significant gas reserves world-wide, represents a challenge for the entire oil and gas industry. The development of new technologies to enhance tight gas reservoir productivity is strongly dependent on an improved understanding of the rock properties and especially the pore framework. Numerous methods are now available to characterize sandstone cores. However, the pore space characterization at pore scale remains difficult due to the fine pore size and delicate sample preparation, and has thus been mostly indirectly inferred until now. Here we propose a new method of ultra high-resolution petrography combining high resolution SEM and argon ion beam cross sectioning (BIB, Broad Ion Beam) which prepares smooth and damage free surfaces. We demonstrate this method using the example of Permian (Rotliegend) age tight gas sandstone core samples. The combination of Ar-beam cross-sectioning facility and high-resolution SEM imaging has the potential to result in a step change in the understanding of pore geometries, in terms of its morphology, spatial distribution and evolution based on the generation of unprecedented image quality and resolution enhancing the predictive reliability of image analysis.

  17. Imaging pore space in tight gas sandstone reservoir: insights from broad ion beam cross-sectioning

    Directory of Open Access Journals (Sweden)

    Konstanty J.

    2010-06-01

    Full Text Available Monetization of tight gas reservoirs, which contain significant gas reserves world-wide, represents a challenge for the entire oil and gas industry. The development of new technologies to enhance tight gas reservoir productivity is strongly dependent on an improved understanding of the rock properties and especially the pore framework. Numerous methods are now available to characterize sandstone cores. However, the pore space characterization at pore scale remains difficult due to the fine pore size and delicate sample preparation, and has thus been mostly indirectly inferred until now. Here we propose a new method of ultra high-resolution petrography combining high resolution SEM and argon ion beam cross sectioning (BIB, Broad Ion Beam which prepares smooth and damage free surfaces. We demonstrate this method using the example of Permian (Rotliegend age tight gas sandstone core samples. The combination of Ar-beam cross-sectioning facility and high-resolution SEM imaging has the potential to result in a step change in the understanding of pore geometries, in terms of its morphology, spatial distribution and evolution based on the generation of unprecedented image quality and resolution enhancing the predictive reliability of image analysis.

  18. Impact of interfacial tension on residual CO2 clusters in porous sandstone

    Science.gov (United States)

    Jiang, Fei; Tsuji, Takeshi

    2015-03-01

    We develop a numerical simulation that uses the lattice Boltzmann method to directly calculate the characteristics of residual nonwetting-phase clusters to quantify capillary trapping mechanisms in real sandstone. For this purpose, a digital-rock-pore model reconstructed from micro-CT-scanned images of Berea sandstone is filtered and segmented into a binary file. The residual-cluster distribution is generated following simulation of the drainage and imbibition processes. The characteristics of the residual cluster in terms of size distribution, major length, interfacial area, and sphericity are investigated under conditions of different interfacial tension (IFT). Our results indicate that high interfacial tension increases the residual saturation and leads to a large size distribution of residual clusters. However, low interfacial tension results in a larger interfacial area, which is beneficial for dissolution and reaction processes during geological carbon storage. Analysis of the force balance acting on the residual clusters demonstrates that trapping stability is higher in high interfacial tension case, and the interfacial tension should be a controlling factor for the trapping stability in addition to the pore geometry and connectivity. The proposed numerical method can handle the complex displacement of multicomponent systems in porous media. By using this method, we can obtain residual-cluster distributions under different conditions for optimizing the storage capacity of carbon-storage projects.

  19. Effect of Sterilization by Dry Heat or Autoclaving on Bacterial Penetration through Berea Sandstone.

    Science.gov (United States)

    Jenneman, G E; McInerney, M J; Crocker, M E; Knapp, R M

    1986-01-01

    A study was undertaken to determine why bacteria could penetrate lengths of consolidated sandstone (Berea) faster when the sandstone was sterilized by autoclaving than when dry heat (150 degrees C, 3 h) was used. Changes in permeability, porosity, and pore entrance size of the rock as a result of autoclaving were not sufficient to explain the differences in penetration times observed, but electron dispersion spectroscopy and electron microscopy of the rock revealed changes in mineral composition and clay morphology. Autoclaved cores contained more chloride than dry-heated cores, and the clays of autoclaved cores were aggregated and irregularly shaped. Therefore, the decreases in bacterial penetration rates caused by autoclave sterilization were probably the result of a change in surface charge of the pores of the rock and of a reduction in surface area of clays available for adhesion. The results implied that dry-heat sterilization was preferable to autoclaving when examining biotic and abiotic interactions in a native-state rock model.

  20. Significance of Lockeia and associated trace fossils from the Bada Bagh Member, Jaisalmer Formation, Rajasthan

    Indian Academy of Sciences (India)

    Amruta R Paranjape; Kantimati G Kulkarni; Shweta S Gurav

    2013-10-01

    A Lockeia-Protovirgularia ichnofauna representing the Cruziana ichnofacies is reported from a calcareous sandstone horizon of the Callovian Bada Bagh Member, Jaisalmer Formation, Rajasthan. The ichnoassemblage is characterized by Lockeia cunctator, L. siliquaria, Protovirgularia ?bidirectionalis, P. rugosa, Ptychoplasma vagans along with Palaeophycus tubularis, P. striatus, Heliophycus isp. And Lophoctenium isp. Use of numerical analysis yielding length to width ratio, slopes and coefficient of determination helps in confirming identification of ichnospecies of Lockeia. Fine morphological details of Lockeia and Protovirgularia, especially sharp and closely spaced chevrons of Protovirgularia, indicate that the substrate in which they were emplaced was stiff, resistant, dewatered and better consolidated. Therefore, it construes that this ichnoassemblage belonging to the classical Cruziana ichnofacies occurs in stiff softground and not a typical softground. Though the ichnofacies of this calcareous sandstone bed indicates low-medium energy condition under subtidal environment of deposition, underlying strata containing Arenicolites, Skolithos and Curvolithus of Skolithos ichnofacies indicate intertidal sandy shore environment with high energy conditions. Thus, it is concluded that this area was undergoing continuous, gradual deepening. However, the percentage of Thalassinoides, Ophiomorpha and Phycodes in the overlying bed is quite high suggesting an increase in the energy conditions resulting from a probable shallowing.

  1. Predictive modeling of CO2 sequestration in deep saline sandstone reservoirs: Impacts of geochemical kinetics

    Energy Technology Data Exchange (ETDEWEB)

    Balashov, Victor N.; Guthrie, George D.; Hakala, J. Alexandra; Lopano, Christina L.; Rimstidt, J. Donald; Brantley, Susan L.

    2013-03-01

    One idea for mitigating the increase in fossil-fuel generated CO{sub 2} in the atmosphere is to inject CO{sub 2} into subsurface saline sandstone reservoirs. To decide whether to try such sequestration at a globally significant scale will require the ability to predict the fate of injected CO{sub 2}. Thus, models are needed to predict the rates and extents of subsurface rock-water-gas interactions. Several reactive transport models for CO{sub 2} sequestration created in the last decade predicted sequestration in sandstone reservoirs of ~17 to ~90 kg CO{sub 2} m{sup -3|. To build confidence in such models, a baseline problem including rock + water chemistry is proposed as the basis for future modeling so that both the models and the parameterizations can be compared systematically. In addition, a reactive diffusion model is used to investigate the fate of injected supercritical CO{sub 2} fluid in the proposed baseline reservoir + brine system. In the baseline problem, injected CO{sub 2} is redistributed from the supercritical (SC) free phase by dissolution into pore brine and by formation of carbonates in the sandstone. The numerical transport model incorporates a full kinetic description of mineral-water reactions under the assumption that transport is by diffusion only. Sensitivity tests were also run to understand which mineral kinetics reactions are important for CO{sub 2} trapping. The diffusion transport model shows that for the first ~20 years after CO{sub 2} diffusion initiates, CO{sub 2} is mostly consumed by dissolution into the brine to form CO{sub 2,aq} (solubility trapping). From 20-200 years, both solubility and mineral trapping are important as calcite precipitation is driven by dissolution of oligoclase. From 200 to 1000 years, mineral trapping is the most important sequestration mechanism, as smectite dissolves and calcite precipitates. Beyond 2000 years, most trapping is due to formation of aqueous HCO{sub 3}{sup -}. Ninety-seven percent of the

  2. Genesis Types and Diagenesis Compaction Mechanisms of Sandstone Rreservoirs in Dynamic Environments in Oil/Gas Basins in China

    Institute of Scientific and Technical Information of China (English)

    Shou Jianfeng; Si Chunsong; Wang Xin

    2006-01-01

    The diversity of sandstone diagenesis mechanisms caused by the complex geological conditions of oil/gas basins in China could hardly be reasonably explained by the traditional concept of burial diagenesis. Three genesis types of thermal diagenesis, tectonic diagenesis and fluid diagenesis are presented on the basis of the dynamic environment of the oil/gas basins and the controlling factors and mechanisms of sandstone diagenesis. Thermal diagenesis of sandstone reservoirs is related not only to the effect of formation temperature on diagenesis, but also to the significant changes in diagenesis caused by geothermal gradients. The concept of thermal compaction is presented. Thermal compaction becomes weaker with increasing depth and becomes stronger at a higher geothermal gradient. At the same formation temperature, the sandstone porosity in the region with a lower geothermal gradient is e0.077+0.0042T times higher than that in the region with a higher geothermal gradient. Both sudden and gradual changes are observed in diagenetic evolution caused by structural deformation. Average sandstone compaction increased by 0.1051% for every 1.0MPa increase of lateral tectonic compressional stress, while late tectonic napping helped to preserve a higher porosity of underlying sandstone reservoir. Fluid diagenesis is a general phenomenon. The compaction caused by fluid properties is significant. The coarser the grain size, the stronger the fluid effect on compaction. The greater the burial depth, the weaker the fluid effect on compaction for the specific reservoir lithology and the greater the difference in the fluid effects on compaction between different grain sizes.

  3. Failure characteristics of two porous sandstones subjected to true triaxial stresses: Applied through a novel loading path

    Science.gov (United States)

    Ma, Xiaodong; Rudnicki, John W.; Haimson, Bezalel C.

    2017-04-01

    We performed an extensive suite of true triaxial experiments in two porous sandstones, Bentheim (porosity ≈ 24%) and Coconino (17%). The experiments were conducted using a novel loading path, which maintains constant Lode angle (Θ) throughout the test. This path enabled the examination of the effects of Lode angle and mean stress on failure (σoct,f). Our tests covered σ3 magnitudes between 0 and 150 MPa and of Θ at -30° (axisymmetric extension), -16°, 0°, +11°, +21°, and +30° (axisymmetric compression). Test results revealed the respective contribution of each of the two stress invariants to failure stress, failure plane angle, and failure mode. In both sandstones, the shear stress required for failure increases with mean stress but decreases with Θ when shear failure mode dominates. However, the dependence of failure stress on mean stress and Θ is reversed when the compactive failure mode is in control. The compactive failure mode was evident in Bentheim sandstone when compaction bands were observed under high mean stress. The Coconino sandstone did not reach the compactive failure regime within the maximum confinement applied. The failure plane angle monotonically decreases with increasing mean stress and Θ. For Coconino sandstone, failure plane angle varies between 80° and 50° for σoct,f between 50 and 450 MPa whereas it drops to 0° as σoct,f, approaches 250 MPa in Bentheim sandstone. We employed the bifurcation theory to relate the stress conditions at failure to the development of failure planes. The theory is in qualitative agreement with the experimental data.

  4. Electrofacies vs. lithofacies sandstone reservoir characterization Campanian sequence, Arshad gas/oil field, Central Sirt Basin, Libya

    Science.gov (United States)

    Burki, Milad; Darwish, Mohamed

    2017-06-01

    The present study focuses on the vertically stacked sandstones of the Arshad Sandstone in Arshad gas/oil field, Central Sirt Basin, Libya, and is based on the conventional cores analysis and wireline log interpretation. Six lithofacies types (F1 to F6) were identified based on the lithology, sedimentary structures and biogenic features, and are supported by wireline log calibration. From which four types (F1-F4) represent the main Campanian sandstone reservoirs in the Arshad gas/oil field. Lithofacies F5 is the basal conglomerates at the lower part of the Arshad sandstones. The Paleozoic Gargaf Formation is represented by lithofacies F6 which is the source provenance for the above lithofacies types. Arshad sediments are interpreted to be deposited in shallow marginal and nearshore marine environment influenced by waves and storms representing interactive shelf to fluvio-marine conditions. The main seal rocks are the Campanian Sirte shale deposited in a major flooding events during sea level rise. It is contended that the syn-depositional tectonics controlled the distribution of the reservoir facies in time and space. In addition, the post-depositional changes controlled the reservoir quality and performance. Petrophysical interpretation from the porosity log values were confirmed by the conventional core measurements of the different sandstone lithofacies types. Porosity ranges from 5 to 20% and permeability is between 0 and 20 mD. Petrophysical cut-off summary of the lower part of the clastic dominated sequence (i. e. Arshad Sandstone) calculated from six wells includes net pay sand ranging from 19.5‧ to 202.05‧, average porosity from 7.7 to 15% and water saturation from 19 to 58%.

  5. Provenance shift in Cambrian mid-Baltica: detrital zircon chronology of Ediacaran–Cambrian sandstones in Estonia

    Directory of Open Access Journals (Sweden)

    Yukio Isozaki

    2014-12-01

    Full Text Available In order to clarify the tectono-sedimentary history of Paleozoic Baltica, age spectra of detrital zircon grains from the Ediacaran (Kotlin Regional Stage and Lower Cambrian sandstones (lowermost Lontova and Lükati formations in western Estonia in central Baltica were analyzed by LA-ICPMS. The abundant occurrence of Archean to Mesoproterozoic (2800–1000 Ma zircon grains was confirmed in all samples. The new data provided the following information on the provenance of siliciclastic material as well as a major change in the sedimentary regime of the Paleo-Baltic basin during the Early Cambrian: (1 the Ediacaran–Lower Cambrian Paleo-Baltic basin received abundant terrigenous clastics from the core of Baltica underlain by the Archean–Mesoproterozoic crystalline crust, (2 the exposed surface area of the 1600 Ma Rapakivi granites apparently was more extensive during the Ediacaran–Early Cambrian than at present, (3 a major re-organization of the basin geometry occurred in the middle Early Cambrian (ca 530–515 Ma in central Baltica, inducing a change in the sediment supply system, (4 in contrast to the total absence of Neoproterozoic detrital zircon grains before the middle Early Cambrian, their sudden appearance at this time, together with consistent occurrence at least until the mid-Devonian, suggests a significant uplift event located in southeast Baltica and/or in a more easterly land domain (e.g., in Sarmatia, (5 possible sources for the Neoproterozoic zircon grains include the peripheral mobile belts with pan-African signatures around Baltica, e.g., the so-called Gondwanan fragments along the Tornquist margin to the southwest and the Timanian belt along the northeastern margin.

  6. Relations between seismic signals and reservoir properties of tight gas reservoirs in North Germany (Permian Rotliegend sandstones)

    Energy Technology Data Exchange (ETDEWEB)

    Abram, P.; Gaupp, R. [Friedrich-Schiller-Univ., Inst. of Geosciences, Jena (Germany)

    2006-07-01

    Tight gas reservoirs in North Germany consist of sandstones of eolian, fluvial and lacustrine origin in 3,5-5 km (11500-16500 ft) depth. Different mechanical compaction, mineral authigenesis and cement dissolution resulted in proximate zones with good and poor reservoir qualities. Some regions with moderate porosities provide very low permeabilities whereas regions with low porosities can offer profitable permeabilities within comparable depositional lithologies. Therefore deep gas exploration is very dependent on predictive reservoir information from 3D seismic signals due to the locally varying reservoir qualities. A recent study succeeded in subdividing a tight gas reservoir into parts with good, moderate and poor qualities and to predict reservoir properties for parts without well information. For this purpose 3D seismic signals had been classified with Neural Network techniques based on amplitude, shape and lateral coherency of seismic traces. The unsupervised classification (Kohonen map) with a single layer of neurons generated classes, which are representative for seismic wave and rock properties at the reservoir level. The geographical distribution of these seismic facies classes correlates to locations of wells with either good or poor reservoir qualities and to zones of specific petrophysical, petrological and sedimentological data. Wells with mean permeabilities between 9-50 mD are located within the red areas (seismic classes 6 and 7), while wells with mean permeabilities below 0,5 mD are all found in blue and green areas (seismic classes 1 till 4). Furthermore, the red zone in the East corresponds to the eastern part of a production field of high transmissivity. The main reason for the strong reduction in mean permeability was found to be a specific morphotype of authigenic illite which occurs almost only in the blue and green zones. This paper outlines SOME theories and results of the doctoral thesis.

  7. Chemical effects of carbon dioxide sequestration in the Upper Morrow Sandstone in the Farnsworth, Texas, hydrocarbon unit

    Energy Technology Data Exchange (ETDEWEB)

    Ahmmed, Bulbul; Appold, Martin S.; Fan, Tianguang; McPherson, Brian J. O. L.; Grigg, Reid B.; White, Mark D.

    2016-03-01

    Numerical geochemical modeling was used to study the effects on pore-water composition and mineralogy from carbon dioxide (CO2) injection into the Pennsylvanian Morrow B Sandstone in the Farnsworth Unit in northern Texas to evaluate its potential for long-term CO2 sequestration. Speciation modeling showed the present Morrow B formation water to be supersaturated with respect to an assemblage of zeolite, clay, carbonate, mica, and aluminum hydroxide minerals and quartz. The principal accessory minerals in the Morrow B, feldspars and chlorite, were predicted to dissolve. A reaction-path model in which CO2 was progressively added up to its solubility limit into the Morrow B formation water showed a decrease in pH from its initial value of 7 to approximately 4.1 to 4.2, accompanied by the precipitation of small amounts of quartz, diaspore, and witherite. As the resultant CO2-charged fluid reacted with more of the Morrow B mineral matrix, the model predicted a rise in pH, reaching a maximum of 5.1 to 5.2 at a water–rock ratio of 10:1. At a higher water–rock ratio of 100:1, the pH rose to only 4.6 to 4.7. Diaspore, quartz, and nontronite precipitated consistently regardless of the water–rock ratio, but the carbonate minerals siderite, witherite, dolomite, and calcite precipitated at higher pH values only. As a result, CO2 sequestration by mineral trapping was predicted to be important only at low water–rock ratios, accounting for a maximum of 2% of the added CO2 at the lowest water–rock ratio investigated of 10:1, which corresponds to a small porosity increase of approximately 0.14% to 0.15%.

  8. Characteristics of deltaic deposits in the Cretaceous Pierre Shale, Trinidad Sandstone, and Vermejo Formation, Raton Basin, Colorado.

    Science.gov (United States)

    Flores, R.M.; Tur, S.M.

    1982-01-01

    Detailed facies analyses of closely spaced measured surface sections in the Trinidad and adjacent areas of Colorado reflect deposition in the river-influenced delta. That this deltaic system was accompanied by abandonment of subdeltas is indicated by a destructional-deltaic facies of heavily bioturbated, carbonaceous sandstones, siltstones, and shales best recorded in the delta front deposits of the Trinidad Sandstone. Coal accumulation of the Vermejo deposits nevertheless remained primarily controlled by persistent organic sedimentation in interdistributary backswamps. These backswamps, which accumulated thick, lenticular coals, were formed during the normal constructional phase of the delta plain. -from Authors

  9. Nutrient Resuscitation and Growth of Starved Cells in Sandstone Cores: a Novel Approach to Enhanced Oil Recovery

    OpenAIRE

    Lappin-Scott, H. M.; Cusack, F.; Costerton, J W

    1988-01-01

    Klebsiella pneumoniae, which was reduced in size (0.25 by 0.5 μm) by carbon deprivation, was injected into a series of sandstone cores and subjected to separate treatments. Scanning electron microscopy of 400-mD cores showed these small starved cells in nearly every core section. The cells were a mixture of small rods and cocci with little or no biofilm production. Continuous or dose stimulation with sodium citrate allowed the cells to grow throughout the sandstone and completely plug the len...

  10. Geology and petrophysical characterization of the Ferron Sandstone for 3-D simulation of a fluvial-deltaic reservoir. Annual report, October 1, 1996--September 30, 1997

    Energy Technology Data Exchange (ETDEWEB)

    Chidsey, T.C. Jr.; Anderson, P.B.; Morris, T.H.; Dewey, J.A. Jr.; Mattson, A.; Foster, C.B.; Snelgrove, S.H.; Ryer, T.A.

    1998-05-01

    The objective of the Ferron Sandstone (Utah) project is to develop a comprehensive, interdisciplinary, quantitative characterization of a fluvial-deltaic reservoir to allow realistic interwell and reservoir-scale models to be developed for improved oil-field development in similar reservoirs world-wide. Both new and existing data is being integrated into a 3-D model of spatial variations in porosity, storativity, and tensorial rock permeability at a scale appropriate for inter-well to regional-scale reservoir simulation. Simulation results could improve reservoir management through proper infill and extension drilling strategies, reduction of economic risks, increased recovery from existing oil fields, and more reliable reserve calculations. The project is divided into four tasks: (1) regional stratigraphic analysis, (2) case studies, (3) reservoirs models, and (4) field-scale evaluation of exploration strategies. The primary objective of the regional stratigraphic analysis is to provide a more detailed interpretation of the stratigraphy and gross reservoir characteristics of the Ferron Sandstone as exposed in outcrop. The primary objective of the case-studies work is to develop a detailed geological and petrophysical characterization, at well-sweep scale or smaller, of the primary reservoir lithofacies typically found in a fluvial-dominated deltaic reservoir. Work on tasks 3 and 4 consisted of developing two- and three-dimensional reservoir models at various scales. The bulk of the work on these tasks is being completed primarily during the last year of the project, and is incorporating the data and results of the regional stratigraphic analysis and case-studies tasks.

  11. Power-law Scaling of Fracture Aperture Sizes in Otherwise-Undeformed Foreland Basin Sandstone: An Example From the Cozzette Sandstone, Piceance Basin, Colorado

    Science.gov (United States)

    Hooker, J. N.; Gale, J. F.; Laubach, S. E.; Gomez, L. A.; Marrett, R.; Reed, R. M.

    2007-12-01

    Power-law variation of aperture size with cumulative frequency has been documented in vein arrays, but such patterns have not been conclusively demonstrated from open or incompletely mineralized opening-mode fractures (joints) in otherwise-undeformed sedimentary rocks. We used subhorizontal core from the nearly flat- lying Cretaceous Cozzette Sandstone, Piceance Basin, Colorado, to document fracture aperture sizes over five orders of magnitude. We measured microfractures (0.0004-0.1164 mm in aperture) along a 276-mm-long scanline using scanning electron microscope-based cathodoluminescence; we measured macrofractures (0.5- 2.15 mm in aperture) in 35 m of approximately horizontal core cut normal to fracture strike. Microfractures are typically filled with quartz. Macrofractures are mostly open and resemble non-mineralized joints, except for thin veneers of quartz cement lining their walls. Micro- and macrofractures share both a common orientation and the same timing with respect to diagenetic sequence, only differing in size and the degree to which they are filled with quartz cement. Power-law scaling equations were derived by fitting trendlines to aperture vs. cumulative frequency data for the microfractures. These equations successfully predicted the cumulative frequencies of the macrofractures, accurate to within a factor of four in each test and within a factor of two in 75 percent of tests. Our results show that tectonic deformation is not prerequisite for power-law scaling of fractures, but instead suggest that scaling emerges from fracture interaction during propagation.

  12. Reservoir characteristics of detrital sandstones in Zhuhai formation of Baiyun sag, Pearl River Mouth Basin%珠江口盆地白云凹陷珠海组碎屑岩储层特征及成因机制

    Institute of Scientific and Technical Information of China (English)

    吕成福; 陈国俊; 张功成; 杜贵超; 王琪; 李超; 李伟; 陈吉

    2011-01-01

    通过岩石铸体薄片、粒度分析和压汞分析等手段,分析白云凹陷珠海组储层的岩石学特征和物性演化特征,研究沉积环境和成岩演化过程对储层特征的影响机制.研究结果表明:储层主要以长石质石英砂岩和长石岩屑质石英砂岩为主,颗粒支撑并以碳酸盐、自生石英和黏土矿物接触式胶结.储层物性总体具有中低孔中低渗特征,以粒间溶蚀扩大孔为主,其次为珠海组底部黏土膜保护的原生孔隙,分选好的中-粗喉型喉道使孔隙连通性良好;在凹陷西斜坡,珠海组上部和底部分别发育钙质砂岩夹层和铁泥质砂岩夹层.三角洲前缘环境是珠海组储层物性良好的先决条件;酸性流体的溶蚀溶解作用和绿泥石黏土膜保护是储层物性较好的根本原因,压实作用是粒间孔隙损失的主要原因,而部分储层渗透率较低是因为自生石英和黏土矿物充填喉道;钙质砂岩夹层物性差是胶结作用所致,而铁泥质砂岩夹层物性差是压实和胶结共同作用的结果.%Based on analyses of casting thin sections and particle size, mercury porosity measurements of the reservoir sandstones from Zhuhai formation of Baiyun sag, the petrography, pore types, pore-throat structure, reservoir quality evolution, diagenetic stage and diagenesis and their effects on reservoir quality were studied. The results show that reservoir sandstones mainly consist of feldspathic quartz sandstone and feldspar lithic quartz sandstone. Detrital grains are grain-supported and cemented by carbonate cements, authigenic quartz and clay minerals. Reservoir properties in general have medium-low porosity and permeability, pores are mainly intergranular dissolved pores and the next is residual primary pores protect by clay film preserved in the bottom Zhuhai formation. Due to pore-throats which are good sorted, pores show good connectivity. In the western slope of the sag, calcareous sandstone and

  13. Energy-Absorbing Beam Member

    Science.gov (United States)

    Littell, Justin D. (Inventor)

    2017-01-01

    An energy-absorbing (EA) beam member and having a cell core structure is positioned in an aircraft fuselage proximate to the floor of the aircraft. The cell core structure has a length oriented along a width of the fuselage, a width oriented along a length of the fuselage, and a depth extending away from the floor. The cell core structure also includes cell walls that collectively define a repeating conusoidal pattern of alternating respective larger and smaller first and second radii along the length of the cell core structure. The cell walls slope away from a direction of flight of the aircraft at a calibrated lean angle. An EA beam member may include the cell core structure and first and second plates along the length of the cell core structure on opposite edges of the cell material.

  14. Re-membering Eastern Europe

    DEFF Research Database (Denmark)

    Wilken, Lisanne

    2016-01-01

    Since the break-down of the Soviet Union and the inclusion of a growing number of Post-Soviet countries into the Eurovision Song Contest, the contest has become an occurring occasion for remembering and discussing the nature and limits of “Europe”. This paper explores how the inclusion of Post-So......, Ukraine and Russia in order to explore how they are re-membered in relation to various perceptions of Europe....

  15. Towards mobile staff members management

    Science.gov (United States)

    Encheva, Sylvia

    2017-07-01

    Todays project management requires a number of abilities which involve finding quick solutions to shortage of staff members with possession of specific qualities. When persons with team responsibilities are under pressure or due to various circumstances are unable to perform exhaustive search in databases, an interactive visualization tool can come in quite handy in finding good solutions unforeseen occurrences. In particular we propose application of selected graphs for facilitating mobile human resource management.

  16. ASCLS members perceptions regarding research.

    Science.gov (United States)

    Mundt, Lillian; Shanahan, Kristy

    2009-01-01

    One of the benchmarks of a profession is performing, publishing, and presenting research. However, in the Clinical Laboratory Science (CLS) profession, few manuscripts are submitted to the American Society for Clinical Laboratory Science (ASCLS) journal, Clinical Laboratory Science, on a regular basis. The problem is that perceptions regarding research, and the role of laboratory professional as researchers, held by ASCLS members may be contributing to the low number of manuscript submissions. To assess these perceptions, an anonymous Likert-scale survey was developed and delivered online using Survey Monkey. Members of ASCLS, with email addresses, were chosen to participate in this survey because they may be most likely to contribute manuscripts for a journal by their own society. About 10% of the 7,000 members who were invited by email chose to participate in this study. Most participants agreed that 1) there is important information to be gathered from research on clinical laboratory specimen results (99.6%), 2) research contributes valuable information to the body of CLS knowledge (99.2%), and 3) conducting research is one of the benchmarks of a profession (92.4%). The majority of participants felt that there are inadequate resources (68.8%) and not enough time (83%) available to conduct research in the clinical laboratory setting. Most participants recognize that many laboratory activities constitute research (86.2%), but only a few are willing to publish research findings on their own (29.2%). Those who are the most likely to publish research findings include men, university faculty, and members who are over 60 years old. University faculty are the most likely to assist others in the writing process. These results show an opportunity exists for ASCLS to foster collaborations between bench technologists and educators willing to assist with the publication process.

  17. Toothbrush contamination in family members

    Directory of Open Access Journals (Sweden)

    Adolfo Contreras

    2010-04-01

    Full Text Available Objective: The purpose of this study was to determine the bacterial contamination of toothbrushes in family members. Materials and Methods: One hundred and two healthy subjects were included in this descriptive study. Every individual was examined clinically and microbiologically using the CPITN index and collecting subgingival plaque samples. Each participant received a toothbrush for home use and after one month they returned it to the investigators. All toothbrushes were cultured to determine the presence of periodontopathic bacteria and enteric rods. Wilkoxon signed rank test and t student test (P d"0.05 were used to compare differences in the subgingival microbiota and toothbrush contamination and CPITN index among family members. Results: A high proportion of toothbrushes resulted highly contaminated with enteric rods (P d"0.001 compared to the subgingival environment where periodontopathic bacteria were more prevalent. The most frequent microorganisms found in toothbrushes used by parents and children for one month were Enterobacteriaceae, Pseudomonadaceae species (>50% and Fusobacterium spp (30%. Conclusions: High levels of enteric rods were commonly detected in toothbrushes used for 1 month among members of the families. These opportunistic organisms may have an important role in oral infections including gingivitis and periodontitis. Monthly replacement or disinfection of the toothbrush can reduce the risk of bacterial transmission/translocation and thus diminish the incidence of biofilm associated oral diseases.

  18. Selective sandstone deterioration in the cathedrals of Salamanca, Textural anisotropy as a cause

    Directory of Open Access Journals (Sweden)

    Martín Patino, María Teresa

    1994-09-01

    Full Text Available Textural sandstone anisotropy is related to the selective deterioration of such stone in buildings. The samples studied come from the Cathedrals of Salamanca. Stone fragments, cut in different directions with regard to the base supporting the ashlars in the wall, are studied by means of a binocular magnifying glass and the Scanning Electron Microscopy (SEM. This shows that the sandstone microfabric has a granular and a laminar microtexture, which correspond to different directions in the plane in question as regards the position of the ashlar. Either of these circumstances coincides with the stone surface on the outside of the building and affect its surface deterioration in a different way. The SEM images of deteriorated stone were compared with those of unaffected stone, with both types coming from differently orientated cuts as regards the position of the ashlar. In conclusion, the position given to the block of stone in the building is of importance for the preservation of the stone. The speed of ultrasound transmission measured in samples from commercial quarries confirms the textural sandstone anisotropy to a greater or lesser extent.

    La anisotropía textural de las areniscas se relaciona con la selectividad de su deterioro en los edificios. Las muestras estudiadas pertenecen a las Catedrales de Salamanca. Fragmentos de piedra, cortados en direcciones diferentes respecto a la base sobre la que se asientan los sillares en el muro, son estudiados por medio de la lupa binocular y del microscopio electrónico de barrido (SEM. De éstos se deduce que la microfábrica de las areniscas tiene una microtextura granular y otra laminar, que corresponden a direcciones diferentes del plano respecto al asiento del sillar. Una u otra de estas situaciones coincide con la superficie de la piedra expuesta al exterior en el edificio, y afectan a su deterioro superficial de forma diferente. Las capas externas en las que predomina la arcilla

  19. Understanding creep in sandstone reservoirs - theoretical deformation mechanism maps for pressure solution in granular materials

    Science.gov (United States)

    Hangx, Suzanne; Spiers, Christopher

    2014-05-01

    Subsurface exploitation of the Earth's natural resources removes the natural system from its chemical and physical equilibrium. As such, groundwater extraction and hydrocarbon production from subsurface reservoirs frequently causes surface subsidence and induces (micro)seismicity. These effects are not only a problem in onshore (e.g. Groningen, the Netherlands) and offshore hydrocarbon fields (e.g. Ekofisk, Norway), but also in urban areas with extensive groundwater pumping (e.g. Venice, Italy). It is known that fluid extraction inevitably leads to (poro)elastic compaction of reservoirs, hence subsidence and occasional fault reactivation, and causes significant technical, economic and ecological impact. However, such effects often exceed what is expected from purely elastic reservoir behaviour and may continue long after exploitation has ceased. This is most likely due to time-dependent compaction, or 'creep deformation', of such reservoirs, driven by the reduction in pore fluid pressure compared with the rock overburden. Given the societal and ecological impact of surface subsidence, as well as the current interest in developing geothermal energy and unconventional gas resources in densely populated areas, there is much need for obtaining better quantitative understanding of creep in sediments to improve the predictability of the impact of geo-energy and groundwater production. The key problem in developing a reliable, quantitative description of the creep behaviour of sediments, such as sands and sandstones, is that the operative deformation mechanisms are poorly known and poorly quantified. While grain-scale brittle fracturing plus intergranular sliding play an important role in the early stages of compaction, these time-independent, brittle-frictional processes give way to compaction creep on longer time-scales. Thermally-activated mass transfer processes, like pressure solution, can cause creep via dissolution of material at stressed grain contacts, grain

  20. Subcritical crack growth under mode I, II, and III loading for Coconino sandstone

    Science.gov (United States)

    Ko, Tae Young

    In systems subjected to long-term loading, subcritical crack growth is the principal mechanism causing the time-dependent deformation and failure of rocks. Subcritical crack growth is environmentally-assisted crack growth, which can allow cracks to grow over a long period of time at stresses far smaller than their failure strength and at tectonic strain rates. The characteristics of subcritical crack growth can be described by a relationship between the stress intensity factor and the crack velocity. This study presents the results of studies conducted to validate the constant stress-rate test for determining subcritical crack growth parameters in Coconino sandstone, compared with the conventional testing method, the double torsion test. The results of the constant stress-rate test are in good agreement with the results of double torsion test. More importantly, the stress-rate tests can determine the parameter A with a much smaller standard deviation than the double torsion test. Thus the constant stress-rate test seems to be both a valid and preferred test method for determining the subcritical crack growth parameters in rocks. We investigated statistical aspects of the constant stress-rate test. The effects of the number of tests conducted on the subcritical crack growth parameters were examined and minimum specimen numbers were determined. The mean and standard deviation of the subcritical crack growth parameters were obtained by randomly selecting subsets from the original strength data. In addition, the distribution form of the subcritical crack growth parameters and the relation between the parameter n and A were determined. We extended the constant stress-rate test technique to modes II and III subcritical crack growth in rocks. The experimental results of the modes I, II and III tests show that the values of the subcritical crack growth parameters are similar to each other. The subcritical crack growth parameter n value for Coconino sandstone has the range

  1. Paleohydrologic controls on soft-sediment deformation in the Navajo Sandstone

    Science.gov (United States)

    Bryant, Gerald; Cushman, Robert; Nick, Kevin; Miall, Andrew

    2016-10-01

    Many workers have noted the presence of contorted cross-strata in the Navajo Sandstone and other ancient eolianites, and have recognized their significance as indicators of sediment saturation during the accumulation history. Horowitz (1982) proposed a general model for the production of such features in ancient ergs by episodic, seismically induced liquefaction of accumulated sand. A key feature of that popular model is the prevalence of a flat water table, characteristic of a hyper-arid climatic regime, during deformation. Under arid climatic conditions, the water table is established by regional flow and liquefaction is limited to the saturated regions below the level of interdune troughs. However, various paleohydrological indicators from Navajo Sandstone outcrops point toward a broader range of water table configurations during the deformation history of that eolianite. Some outcrops reveal extensive deformation complexes that do not appear to have extended to the contemporary depositional surface. These km-scale zones of deformation, affecting multiple sets of cross-strata, and grading upward into undeformed crossbeds may represent deep water table conditions, coupled with high intensity triggers, which produced exclusively intrastratal deformation. Such occurrences contrast with smaller-scale complexes formed within the zone of interaction between the products of soft-sediment deformation and surface processes of deposition and erosion. The Horowitz model targets the smaller-scale deformation morphologies produced in this near-surface environment. This study examines the implications of a wet climatic regime for the Horowitz deformation model. It demonstrates how a contoured water table, characteristic of humid climates, may have facilitated deformation within active bedforms, as well as in the accumulation. Intra-dune deformation would enable deflation of deformation features during the normal course of dune migration, more parsimoniously accounting for

  2. EFFECT OF SANDSTONE ANISOTROPY ON ITS HEAT AND MOISTURE TRANSPORT PROPERTIES

    Directory of Open Access Journals (Sweden)

    Jan Fořt

    2015-09-01

    Full Text Available Each type of natural stone has its own geological history, formation conditions, different chemical and mineralogical composition, which influence its possible anisotropy. Knowledge in the natural stones anisotropy represents crucial information for the process of stone quarrying, its correct usage and arrangement in building applications. Because of anisotropy, many natural stones exhibit different heat and moisture transport properties in various directions. The main goal of this study is to analyse several anisotropy indices and their effect on heat transport and capillary absorption. For the experimental determination of the anisotropy effect, five types of sandstone coming from different operating quarries in the Czech Republic are chosen. These materials are often used for restoration of culture heritage monuments as well as for other building applications where they are used as facing slabs, facade panels, decoration stones, paving, etc. For basic characterization of studied materials, determination of their bulk density, matrix density and total open porosity is done. Chemical composition of particular sandstones is analysed by X-Ray Fluorescence. Anisotropy is examined by the non-destructive measurement of velocity of ultrasonic wave propagation. On the basis of ultrasound testing data, the relative anisotropy, total anisotropy and anisotropy coefficient are calculated. Then, the measurement of thermal conductivity and thermal diffusivity in various directions of samples orientation is carried out. The obtained results reveal significant differences between the parameters characterizing the heat transport in various directions, whereas these values are in accordance with the indices of anisotropy. Capillary water transport is described by water absorption coefficient measured using a sorption experiment, which is performed for distilled water and 1M NaCl water solution.  The measured data confirm the effect of anisotropy which is

  3. Genesis Analysis of High-Gamma Ray Sandstone Reservoir and Its Log Evaluation Techniques: A Case Study from the Junggar Basin, Northwest China

    Directory of Open Access Journals (Sweden)

    Liang Wang

    2013-01-01

    Full Text Available In the Junggar basin, northwest China, many high gamma-ray (GR