Reservoir characterization of the Mt. Simon Sandstone, Illinois Basin, USA

Science.gov (United States)

Frailey, S.M.; Damico, J.; Leetaru, H.E.

2011-01-01

The integration of open hole well log analyses, core analyses and pressure transient analyses was used for reservoir characterization of the Mt. Simon sandstone. Characterization of the injection interval provides the basis for a geologic model to support the baseline MVA model, specify pressure design requirements of surface equipment, develop completion strategies, estimate injection rates, and project the CO2 plume distribution.The Cambrian-age Mt. Simon Sandstone overlies the Precambrian granite basement of the Illinois Basin. The Mt. Simon is relatively thick formation exceeding 800 meters in some areas of the Illinois Basin. In the deeper part of the basin where sequestration is likely to occur at depths exceeding 1000 m, horizontal core permeability ranges from less than 1 ?? 10-12 cm 2 to greater than 1 ?? 10-8 cm2. Well log and core porosity can be up to 30% in the basal Mt. Simon reservoir. For modeling purposes, reservoir characterization includes absolute horizontal and vertical permeability, effective porosity, net and gross thickness, and depth. For horizontal permeability, log porosity was correlated with core. The core porosity-permeability correlation was improved by using grain size as an indication of pore throat size. After numerous attempts to identify an appropriate log signature, the calculated cementation exponent from Archie's porosity and resistivity relationships was used to identify which porosity-permeability correlation to apply and a permeability log was made. Due to the relatively large thickness of the Mt. Simon, vertical permeability is an important attribute to understand the distribution of CO2 when the injection interval is in the lower part of the unit. Only core analyses and specifically designed pressure transient tests can yield vertical permeability. Many reservoir flow models show that 500-800 m from the injection well most of the CO2 migrates upward depending on the magnitude of the vertical permeability and CO2 injection

Mineralogical controls on porosity and water chemistry during O_2-SO_2-CO_2 reaction of CO_2 storage reservoir and cap-rock core

International Nuclear Information System (INIS)

Pearce, Julie K.; Golab, Alexandra; Dawson, Grant K.W.; Knuefing, Lydia; Goodwin, Carley; Golding, Suzanne D.

2016-01-01

Reservoir and cap-rock core samples with variable lithology's representative of siliciclastic reservoirs used for CO_2 storage have been characterized and reacted at reservoir conditions with an impure CO_2 stream and low salinity brine. Cores from a target CO_2 storage site in Queensland, Australia were tested. Mineralogical controls on the resulting changes to porosity and water chemistry have been identified. The tested siliciclastic reservoir core samples can be grouped generally into three responses to impure CO_2-brine reaction, dependent on mineralogy. The mineralogically clean quartzose reservoir cores had high porosities, with negligible change after reaction, in resolvable porosity or mineralogy, calculated using X-ray micro computed tomography and QEMSCAN. However, strong brine acidification and a high concentration of dissolved sulphate were generated in experiments owing to minimal mineral buffering. Also, the movement of kaolin has the potential to block pore throats and reduce permeability. The reaction of the impure CO_2-brine with calcite-cemented cap-rock core samples caused the largest porosity changes after reaction through calcite dissolution; to the extent that one sample developed a connection of open pores that extended into the core sub-plug. This has the potential to both favor injectivity but also affect CO_2 migration. The dissolution of calcite caused the buffering of acidity resulting in no significant observable silicate dissolution. Clay-rich cap-rock core samples with minor amounts of carbonate minerals had only small changes after reaction. Created porosity appeared mainly disconnected. Changes were instead associated with decreases in density from Fe-leaching of chlorite or dissolution of minor amounts of carbonates and plagioclase. The interbedded sandstone and shale core also developed increased porosity parallel to bedding through dissolution of carbonates and reactive silicates in the sandy layers. Tight interbedded cap

Sedimentological reservoir characteristics of the Paleocene fluvial/lacustrine Yabus Sandstone, Melut Basin, Sudan

Science.gov (United States)

Mahgoub, M. I.; Padmanabhan, E.; Abdullatif, O. M.

2016-11-01

Melut Basin in Sudan is regionally linked to the Mesozoic-Cenozoic Central and Western African Rift System (CWARS). The Paleocene Yabus Formation is the main oil producing reservoir in the basin. It is dominated by channel sandstone and shales deposited in fluvial/lacustrine environment during the third phase of rifting in the basin. Different scales of sedimentological heterogeneities influenced reservoir quality and architecture. The cores and well logs analyses revealed seven lithofacies representing fluvial, deltaic and lacustrine depositional environments. The sandstone is medium to coarse-grained, poorly to moderately-sorted and sub-angular to sub-rounded, arkosic-subarkosic to sublitharenite. On the basin scale, the Yabus Formation showed variation in sandstone bodies, thickness, geometry and architecture. On macro-scale, reservoir quality varies vertically and laterally within Yabus Sandstone where it shows progressive fining upward tendencies with different degrees of connectivity. The lower part of the reservoir showed well-connected and amalgamated sandstone bodies, the middle to the upper parts, however, have moderate to low sandstone bodies' connectivity and amalgamation. On micro-scale, sandstone reservoir quality is directly affected by textures and diagenetic changes such as compaction, cementation, alteration, dissolution and kaolinite clays pore fill and coat all have significantly reduced the reservoir porosity and permeability. The estimated porosity in Yabus Formation ranges from 2 to 20% with an average of 12%; while permeability varies from 200 to 500 mD and up to 1 Darcy. The understanding of different scales of sedimentological reservoir heterogeneities might contribute to better reservoir quality prediction, architecture, consequently enhancing development and productivity.

Laboratory Mid-frequency (Kilohertz) Range Seismic Property Measurements and X-ray CT Imaging of Fractured Sandstone Cores During Supercritical CO2 Injection

Science.gov (United States)

Nakagawa, S.; Kneafsey, T. J.; Chang, C.; Harper, E.

2014-12-01

During geological sequestration of CO2, fractures are expected to play a critical role in controlling the migration of the injected fluid in reservoir rock. To detect the invasion of supercritical (sc-) CO2 and to determine its saturation, velocity and attenuation of seismic waves can be monitored. When both fractures and matrix porosity connected to the fractures are present, wave-induced dynamic poroelastic interactions between these two different types of rock porosity—high-permeability, high-compliance fractures and low-permeability, low-compliance matrix porosity—result in complex velocity and attenuation changes of compressional waves as scCO2 invades the rock. We conducted core-scale laboratory scCO2 injection experiments on small (diameter 1.5 inches, length 3.5-4 inches), medium-porosity/permeability (porosity 15%, matrix permeability 35 md) sandstone cores. During the injection, the compressional and shear (torsion) wave velocities and attenuations of the entire core were determined using our Split Hopkinson Resonant Bar (short-core resonant bar) technique in the frequency range of 1-2 kHz, and the distribution and saturation of the scCO2 determined via X-ray CT imaging using a medical CT scanner. A series of tests were conducted on (1) intact rock cores, (2) a core containing a mated, core-parallel fracture, (3) a core containing a sheared core-parallel fracture, and (4) a core containing a sheared, core-normal fracture. For intact cores and a core containing a mated sheared fracture, injections of scCO2 into an initially water-saturated sample resulted in large and continuous decreases in the compressional velocity as well as temporary increases in the attenuation. For a sheared core-parallel fracture, large attenuation was also observed, but almost no changes in the velocity occurred. In contrast, a sample containing a core-normal fracture exhibited complex behavior of compressional wave attenuation: the attenuation peaked as the leading edge of

Porosity and pore size distribution determination of Tumblagooda formation sandstone by X-ray microtomography

International Nuclear Information System (INIS)

Fernandes, Jaquiel S.; Appoloni, Carlos R.; Moreira, Anderson C.

2007-01-01

Microstructural parameters evaluations of reservoir rocks are very important to petroleum industry. This work presents total porosity and pore size distribution measurement of a sandstone sample from the Tumblagooda formation, collected at Kalbarri National Park in Australia. Porosity and pores size distribution were determined using X-Ray microtomography and imaging techniques. For these measurements, it was employed a micro-CT (μ-CT) Skyscan system model 1172 with conical beam, operated with a 1 mm Al filter at 80 kV and 125 μA, respectively, and a 2000 x 1048 pixels CCD camera. The sample was rotated from 0 deg to 180 deg, in step of 0.5 deg. For the considered sample, this equipment provided images with 2.9 μm spatial resolution. Six hundreds 2-D images where reconstructed with the Skyscan NRecon software, which were analyzed with the aid of Imago software, developed at the Laboratory of Porous Media and Thermophysical Properties (LMPT), Department of Mechanical Engineering, Federal University of Santa Catarina, Brazil, in association with the Brazilian software company Engineering Simulation and Scientific Software (ESSS), and Petroleo Brasileiro SA (PETROBRAS) Research and Development Center (CENPES). The determined average porosity was 11.45 ±1.53 %. Ninety five percent of the porous phase refers to pores with radius ranging from 2.9 to 85.2 μm, presenting the larger frequency (7.7 %) at 11.7 μm radius. (author)

Diagenesis and reservoir quality of the Lower Cretaceous Quantou Formation tight sandstones in the southern Songliao Basin, China

Science.gov (United States)

Xi, Kelai; Cao, Yingchang; Jahren, Jens; Zhu, Rukai; Bjørlykke, Knut; Haile, Beyene Girma; Zheng, Lijing; Hellevang, Helge

2015-12-01

The Lower Cretaceous Quantou Formation in the southern Songliao Basin is the typical tight oil sandstone in China. For effective exploration, appraisal and production from such a tight oil sandstone, the diagenesis and reservoir quality must be thoroughly studied first. The tight oil sandstone has been examined by a variety of methods, including core and thin section observation, XRD, SEM, CL, fluorescence, electron probing analysis, fluid inclusion and isotope testing and quantitative determination of reservoir properties. The sandstones are mostly lithic arkoses and feldspathic litharenites with fine to medium grain size and moderate to good sorting. The sandstones are dominated by feldspar, quartz, and volcanic rock fragments showing various stages of disintegration. The reservoir properties are quite poor, with low porosity (average 8.54%) and permeability (average 0.493 mD), small pore-throat radius (average 0.206 μm) and high displacement pressure (mostly higher than 1 MPa). The tight sandstone reservoirs have undergone significant diagenetic alterations such as compaction, feldspar dissolution, quartz cementation, carbonate cementation (mainly ferrocalcite and ankerite) and clay mineral alteration. As to the onset time, the oil emplacement was prior to the carbonate cementation but posterior to the quartz cementation and feldspar dissolution. The smectite to illite reaction and pressure solution at stylolites provide a most important silica sources for quartz cementation. Carbonate cements increase towards interbedded mudstones. Mechanical compaction has played a more important role than cementation in destroying the reservoir quality of the K1q4 sandstone reservoirs. Mixed-layer illite/smectite and illite reduced the porosity and permeability significantly, while chlorite preserved the porosity and permeability since it tends to be oil wet so that later carbonate cementation can be inhibited to some extent. It is likely that the oil emplacement occurred

Geochemical porosity values obtained in core samples from different clay-rocks

International Nuclear Information System (INIS)

Fernandez, A.M.

2010-01-01

Document available in extended abstract form only. Argillaceous formations of low permeability are considered in many countries as potential host rocks for the disposal of high level radioactive wastes (HLRW). In order to determine their suitability for waste disposal, evaluations of the hydro-geochemistry and transport mechanisms from such geologic formations to the biosphere must be undertaken. One of the key questions about radionuclide diffusion and retention is to know the chemistry and chemical reactions and sorption processes that will occur in the rock and their effects on radionuclide mobility. In this context, the knowledge of the pore water chemistry is essential for performance assessment purposes. This information allows to establish a reliable model for the main water-rock interactions, which control the physico-chemical parameters and the chemistry of the major elements of the system. An important issue in order to model the pore water chemistry in clayey media is to determine the respective volume accessible to cations and anions, i.e, the amount of water actually available for chemical reactions/solute transport. This amount is usually referred as accessible porosity or geochemical porosity. By using the anion inventories, i.e. the anion content obtained from aqueous leaching, and assuming that all Cl - , Br - and SO4 2- leached in the aqueous extracts originates from pore water, the concentration of a conservative ion can be converted into the real pore water concentration if the accessible porosity is known. In this work, the accessible porosity or geochemical porosity has been determined in core samples belonging to four different formations: Boom Clay from Hades URL (Belgium, BE), Opalinus Clay from Mont Terri (Switzerland, CH), and Callovo-Oxfordian argillite from Bure URL (France, FR). The geochemical or chloride porosity was defined as the ratio between the pore water volume containing Cl-bearing pore water and the total volume of a sample

Fuzzy logic application for data correction of gamma ray profile and correlation with effective porosity of core from Resende Basin, Rio de Janeiro; Aplicacao da logica fuzzy para correcao de dados de perfil de raios gama e correlacao com porosidade efetiva de testemunhos da Bacia de Resende, Rio de Janeiro

Energy Technology Data Exchange (ETDEWEB)

Souza, Francisco de Assis Leal de; Tunala, Leonardo Fernandes; Abreu, Carlos Jorge de; Lopes, Ricardo Tadeu, E-mail: pachoteki@yahoo.com.br, E-mail: leotunala@hotmail.com, E-mail: abreu@geologia.ufrj.br, E-mail: ricardo@lin.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ/CCMN), RJ (Brazil). Centro de Ciencias Matematicas e da Natureza. Inst. de Geociencias. Dept. de Geologia; Rocha, Paula Lucia Ferrucio da, E-mail: ferrucio@acd.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil); Martins, Ricardo Rhomberg, E-mail: ricardo301@gmail.com [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola Politenica de Engenharia; Lima, Inaya Correa Barbosa, E-mail: inaya@lin.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Centro de Tecnologia

2010-12-15

This work presents here a study on the porosity of cores from Resende Basin (Rio de Janeiro). The first step involved the selection, thinning of the material (core) and sample preparation for the use of porosimeter to obtain effective porosity. The material studied is sandstone, friable, coarse to very fine of three wells (GPR1, GPR2 and GPR3). The fuzzy logic (MatLab) was applied to the effective porosity data calculated from the gamma ray (GR) profile for the construction of a synthetic profile and from this we could identify the errors made in calculating the data. Then the results of porosity from the core were correlated with data from the corrected effective porosity (gamma ray profile) in order to prove the results obtained with both methods. The analysis of the synthetic porosity calculated by the fuzzy logic has shown that this is a promising method for assessing the quality of data and to obtain good fits. (author)

Experimental Investigation of Crack Extension Patterns in Hydraulic Fracturing with Shale, Sandstone and Granite Cores

Directory of Open Access Journals (Sweden)

Jianming He

2016-12-01

Full Text Available Hydraulic fracturing is an important method of reservoir stimulation in the exploitation of geothermal resources, and conventional and unconventional oil and gas resources. In this article, hydraulic fracturing experiments with shale, sandstone cores (from southern Sichuan Basin, and granite cores (from Inner Mongolia were conducted to investigate the different hydraulic fracture extension patterns in these three reservoir rocks. The different reactions between reservoir lithology and pump pressure can be reflected by the pump pressure monitoring curves of hydraulic fracture experiments. An X-ray computer tomography (CT scanner was employed to obtain the spatial distribution of hydraulic fractures in fractured shale, sandstone, and granite cores. From the microscopic and macroscopic observation of hydraulic fractures, different extension patterns of the hydraulic fracture can be analyzed. In fractured sandstone, symmetrical hydraulic fracture morphology could be formed, while some micro cracks were also induced near the injection hole. Although the macroscopic cracks in fractured granite cores are barely observed by naked eye, the results of X-ray CT scanning obviously show the morphology of hydraulic fractures. It is indicated that the typical bedding planes well developed in shale formation play an important role in the propagation of hydraulic fractures in shale cores. The results also demonstrated that heterogeneity influenced the pathway of the hydraulic fracture in granite cores.

Diagenetic effect on permeabilities of geothermal sandstone reservoirs

DEFF Research Database (Denmark)

Weibel, Rikke; Olivarius, Mette; Kristensen, Lars

The Danish subsurface contains abundant sedimentary deposits, which can be utilized for geothermal heating. The Upper Triassic – Lower Jurassic continental-marine sandstones of the Gassum Formation has been utilised as a geothermal reservoir for the Thisted Geothermal Plant since 1984 extracting...... and permeability is caused by increased diagenetic changes of the sandstones due to increased burial depth and temperatures. Therefore, the highest water temperatures typically correspond with the lowest porosities and permeabilities. Especially the permeability is crucial for the performance of the geothermal......-line fractures. Continuous thin chlorite coatings results in less porosity- and permeability-reduction with burial than the general reduction with burial, unless carbonate cemented. Therefore, localities of sandstones characterized by these continuous chlorite coatings may represent fine geothermal reservoirs...

Fracture toughness testing of core from the Cambro-Ordovician Section on the Oak Ridge Reservation

International Nuclear Information System (INIS)

Lemiszki, P.J.; Landes, J.D.

1996-01-01

The modified ring test was used to determine the mode I fracture toughness of bedrock cores from the DOE Oak Ridge Reservation in east Tennessee. Low porosity sandstones, limestones, and dolostones from the lower part of the Paleozoic section in Copper Creek and Whiteoak Mountain thrust sheets were sampled. In general, the average mode I fracture toughness decreases from sandstone, dolostone, and limestone. The fracture toughness of the limestones varies between rock units, which is related to different sedimentologic characteristics. Quality of results was evaluated by testing cores of Berea Sandstone and Indiana Limestone, which produced results similar to published results

Characterizing Mobile/Less-Mobile Porosity and Solute Exchange in Dual-Domain Media Using Tracer Experiments and Electrical Measurements in a Hassler-Type Core Holder

Science.gov (United States)

Falzone, S.; Slater, L. D.; Day-Lewis, F. D.; Parker, B. L.; Keating, K.; Robinson, J.

2017-12-01

Mass transfer is the process by which solute is retained in less-mobile porosity domains, and later released into the mobile porosity domain. This process is often responsible for the slow arrival and gradual release of contaminants and solute tracers. Recent studies have outlined methods using dual-domain mass transfer (DDMT) models for characterizing this phenomenon. These models use the non-linear relationship of bulk (σb) and fluid (σf) conductivity, collected from electrical methods during tracer experiments, to characterize the less-mobile/mobile porosity ratio (β) and the mass-transfer rate coefficient (α). DDMT models use the hysteretic σb-σf relationship observed while solute tracers are injected and then flushed from a sample media. Due to limitations in observing the hysteretic σb-σf relationship, this method has not been used to characterize low permeability samples. We have developed an experimental method for testing porous rock cores that allows us to develop a fundamental understanding of contaminant storage and release in consolidated rock. We test the approach on cores from sedimentary rock sites where mass transfer is expected to occur between hydraulically connected fractures and the adjacent low permeability rock matrix. Our method uses a Hassler-type core holder, designed to apply confining pressure around the outside of a sample core, which hydraulically isolates the sample core, allowing water to be injected into it at increased pressures. The experimental apparatus was also designed to measure σb with spectral induced polarization (SIP) measurements, and σf from a sampling port located at the center of the core. Cores were initially saturated with a solution with high electrical conductivity ( 80000 μS/cm). DI water was then injected into the cores at elevated pressures (>60 psi) and the saturating solution was flushed from the cores, in order to generate flow rates fast enough to capture the non-linear σb-σf relationship

An interpretation of core and wireline logs for the Petrophysical evaluation of Upper Shallow Marine sandstone reservoirs of the Bredasdorp Basin, offshore South Africa

Science.gov (United States)

Magoba, Moses; Opuwari, Mimonitu

2017-04-01

This paper embodies a study carried out to assess the Petrophysical evaluation of upper shallow marine sandstone reservoir of 10 selected wells in the Bredasdorp basin, offshore, South Africa. The studied wells were selected randomly across the upper shallow marine formation with the purpose of conducting a regional study to assess the difference in reservoir properties across the formation. The data sets used in this study were geophysical wireline logs, Conventional core analysis and geological well completion report. The physical rock properties, for example, lithology, fluid type, and hydrocarbon bearing zone were qualitatively characterized while different parameters such as volume of clay, porosity, permeability, water saturation ,hydrocarbon saturation, storage and flow capacity were quantitatively estimated. The quantitative results were calibrated with the core data. The upper shallow marine reservoirs were penetrated at different depth ranging from shallow depth of about 2442m to 3715m. The average volume of clay, average effective porosity, average water saturation, hydrocarbon saturation and permeability range from 8.6%- 43%, 9%- 16%, 12%- 68% , 32%- 87.8% and 0.093mD -151.8mD respectively. The estimated rock properties indicate a good reservoir quality. Storage and flow capacity results presented a fair to good distribution of hydrocarbon flow.

Structural diagenesis in Upper Carboniferous tight gas sandstones. Lessons learned from the Piesberg analog study

Energy Technology Data Exchange (ETDEWEB)

Steindorf, P.; Hoehne, M.; Becker, S.; Hilgers, C. [RWTH Aachen Univ. (Germany). Energy and Mineral Resources Group (EMR); Koehrer, B. [Wintershall Holding GmbH, Barnstorf (Germany)

2013-08-01

Upper Carboniferous tight gas sandstone reservoirs in NW-Germany consist of thick successions of cyclothems. Our focus is the Westphalian D of the Piesberg quarry near Osnabrueck, which exposes cemented, faulted and jointed third-order coarse- to fine-grained sandstone cycles separated by anthracite coal seams. We characterize the rocks and the lateral variation of rock properties such as porosity to better constrain input data for reservoir modelling. Three cycles are exposed, each approximately 50 m thick. Rock types can be clearly distinguished by spectral gamma ray in the quarry. Sandstones are intensely compacted and cemented with quartz and generally characterized by low porosities < 8 % (Hepycnometry on plugs and cuttings). Porosities are secondary and mainly related to detrital carbonate dissolution. Around faults dissolution is higher and the porosities can increase to up to 25%. The normal faults show different throws in the quarry and bands of shale and coal have smeared into the fault at juxtaposed beds, which may result in compartments. They dominantly strike W-E and NNW-SSE, but subordinate NE-SW striking fault patterns are also present. Joints were analyzed in a 50 x 50 m section of the quarry wall using Lidar (Light detection and ranging) laser scanning, which allows the characterization of the lithology and quantitative measurement of bedding and fracture orientation data in inaccessible areas. NNE-SSW and W-E joint sets are accompanied by northeasterly and northwesterly striking sets. Around faults, fault planes and fractures are cemented with quartz veins, showing localized mass transport. Due to the intense cementation, the sandstones can reach uniaxial strengths of more than 100 MPa normal to bedding, and approximately 50 MPa parallel to bedding. Sandstone beds within and close to faults are leached by fluids, and their uniaxial strength is reduced by a factor of more than two. Our high resolution field data enables a better understanding of

Permeability model of tight reservoir sandstones combining core-plug and miniperm analysis of drillcore; longyearbyen co2lab, Svalbard

NARCIS (Netherlands)

Magnabosco, Cara; Braathen, Alvar; Ogata, Kei

2014-01-01

Permeability measurements in Mesozoic, low-permeability sandstone units within the strata cored in seven drillholes near Longyearbyen, Svalbard, have been analysed to assess the presence of aquifers and their potentials as reservoirs for the storage of carbon dioxide. These targeted sandstones are

Clay squirt: Local flow dispersion in shale-bearing sandstones

DEFF Research Database (Denmark)

Sørensen, Morten Kanne; Fabricius, Ida Lykke

2017-01-01

Dispersion of elastic-wave velocity is common in sandstone and larger in shaly sandstone than in clean sandstone. Dispersion in fluid-saturated shaly sandstone often exceeds the level expected from the stress-dependent elastic moduli of dry sandstone. The large dispersion has been coined clay...... squirt and is proposed to originate from a pressure gradient between the clay microporosity and the effective porosity. We have formulated a simple model that quantifies the clay-squirt effect on bulk moduli of sandstone with homogeneously distributed shale laminae or dispersed shale. The model...... predictions were compared with the literature data. For sandstones with dispersed shale, agreement was found, whereas other sandstones have larger fluid-saturated bulk modulus, possibly due to partially load-bearing shales or heterogeneous shale distribution. The data that agree with the clay-squirt model...

Quantifying multiscale porosity and fracture aperture distribution in granite cores using computed tomography

Science.gov (United States)

Wenning, Quinn; Madonna, Claudio; Joss, Lisa; Pini, Ronny

2017-04-01

Knowledge of porosity and fracture (aperture) distribution is key towards a sound description of fluid transport in low-permeability rocks. In the context of geothermal energy development, the ability to quantify the transport properties of fractures is needed to in turn quantify the rate of heat transfer, and, accordingly, to optimize the engineering design of the operation. In this context, core-flooding experiments coupled with non-invasive imaging techniques (e.g., X-Ray Computed Tomography - X-Ray CT) represent a powerful tool for making direct observations of these properties under representative geologic conditions. This study focuses on quantifying porosity and fracture aperture distribution in a fractured westerly granite core by using two recently developed experimental protocols. The latter include the use of a highly attenuating gas [Vega et al., 2014] and the application of the so-called missing CT attenuation method [Huo et al., 2016] to produce multidimensional maps of the pore space and of the fractures. Prior to the imaging experiments, the westerly granite core (diameter: 5 cm, length: 10 cm) was thermally shocked to induce micro-fractured pore space; this was followed by the application of the so-called Brazilian method to induce a macroscopic fracture along the length of the core. The sample was then mounted in a high-pressure aluminum core-holder, exposed to a confining pressure and placed inside a medical CT scanner for imaging. An initial compressive pressure cycle was performed to remove weak asperities and reduce the hysteretic behavior of the fracture with respect to effective pressure. The CT scans were acquired at room temperature and 0.5, 5, 7, and 10 MPa effective pressure under loading and unloading conditions. During scanning the pore fluid pressure was undrained and constant, and the confining pressure was regulated at the desired pressure with a high precision pump. Highly transmissible krypton and helium gases were used as

Water Vapor Diffusion and Adsorption of Sandstones: Influence of Rock Texture and Composition

Directory of Open Access Journals (Sweden)

Martin Keppert

2016-01-01

Full Text Available The term sandstone is used for wide range of rocks containing quartz clasts which can be cemented by secondary precipitated quartz or calcite; moreover the space between clasts can be filled by matrix. These facts result in existence of numerous rocks having highly various properties. Sandstones have been used as construction materials due to their good accessibility and workability. Since most of sandstones are porous, water vapor can penetrate through sandstone constructions. The rate of water vapor diffusion, as well as the vapor sorption isotherm, was determined for range of sandstone types. The diffusion resistance factor was found to be dependent on the total porosity of sandstone but the sorption behavior was strongly influenced by nature of the particular sandstone; the specific surface area of stone and presence of clay matrix are determining its sorption isotherm. The published data enable estimating (i diffusion resistance factor of a sandstone via knowledge of its total porosity and (ii the sorption isotherm via knowledge of the stone’s nature and specific surface area. This approach can significantly reduce the time necessary to acquire vapor-related properties of a sandstone.

Architecture and quantitative assessment of channeled clastic deposits, Shihezi sandstone (Lower Permian, Ordos Basin, China

Directory of Open Access Journals (Sweden)

Chengye Jia

2017-02-01

Full Text Available Lower Permian Shihezi sandstone in Ordos Basin is the largest gas reservoir in China. Architecture elements of channel, overbank and floodplain facies of braided channel deposits were identified through an outcrops survey, and their proportion of channel facies have been quantitatively estimated from well logging. Characteristics of architecture elements, such as sand thickness, bounding surfaces and lithofacies were investigated through outcrops and core. Petrology of Shihezi sandstone has also been studied in detail. Analysis on sandstone components shows that monocrystalline quartz with approximately 76% bulk volume, and lithic up to 5%–45% bulk volume, are the two main components. Litharenite and lithic quartz sandstone are the main rock types. Compaction is concluded by former researchers as the control factor of low permeability. Examination through thin section reveals that secondary pores developed well in coarse sand. Inter-granular dissolution is included as the positive effect to increasing porosity, and is concluded as the control factor to the generation of net pay. Scale of coarse grained channel fills and channel bar sandstone bodies are quantitatively estimated. Strike-oriented, dip-oriented, and vertical distribution of channel fills and channel bar sandstone bodies have been investigated. The geometry of sand bodies can be depicted as an elongated lens. Subsurface mapping reveals that channel sandstone bodies distribute widely from both lateral and longitudinal cross section profiles, and are poorly connected.

Physical properties of sidewall cores from Decatur, Illinois

Science.gov (United States)

Morrow, Carolyn A.; Kaven, Joern; Moore, Diane E.; Lockner, David A.

2017-10-18

To better assess the reservoir conditions influencing the induced seismicity hazard near a carbon dioxide sequestration demonstration site in Decatur, Ill., core samples from three deep drill holes were tested to determine a suite of physical properties including bulk density, porosity, permeability, Young’s modulus, Poisson’s ratio, and failure strength. Representative samples of the shale cap rock, the sandstone reservoir, and the Precambrian basement were selected for comparison. Physical properties were strongly dependent on lithology. Bulk density was inversely related to porosity, with the cap rock and basement samples being both least porous (

Relationship between petrographic pore types and core measurements in sandstones of the Monserrate Formation, upper Magdalena Valley, Colombia

International Nuclear Information System (INIS)

Ehrlich, R; Cobaleda, G; Barclay, Ferm

1997-01-01

Patterns of porosity in sandstones of the Monserrate Formation (Upper Magdalena Valley) exposed in polished blocks have been digitally recorded using an image processor coupled to a scanning electron microscope operated in back scatter electron mode. Additionally, porosity, permeability and response to mercury injection-capillary pressure tests were measured on some of the imaged samples. Porosity pattern were evaluated via an erosion/dilation-differencing image-processing algorithm and then classified by the self-training classifier, SAWVEC. Changes in the resulting pore type proportions were strongly associated with changes in the mercury porosimetry curves. From the image processing data, five pore types, sufficient to include all of the variability in size and shape of the patterns of porosity, were identified. Variations in the number of pares of each type per unit cross sectional area were related to variations in permeability. The resultant relationships with mercury porosimetry demonstrated that pares of the same type tends to form microcircuits characterized by a limited throat size range. Permeability modeling showed that intergranular Pare Types 2 and 4 (secondary porosity resulting from carbonate dissolution) are responsible for permeability in the 0,01 - 0,1 0 Darcy range. Type 5 pares (large molds) slightly contribute to permeability, except in coarse grained rocks where they are efficiently connected by micro fractures

Comparative sound velocity measurements between porous rock and fully-dense material under crustal condition: The cases of Darley Dale sandstone and copper block

Science.gov (United States)

Kung, J.; Chien, Y. V.; Wu, W.; Dong, J.; Chang, Y.; Tsai, C.; Yang, M.; Wang, K.

2012-12-01

Previous studies showed that the voids and their geometry in the sedimentary rocks have great influence on the compressibility of rock, which reflects on its elastic velocities. Some models were developed to discuss the relations among velocity, porosity and void geometry. Therefore, the information of porosity, and void geometry and its distribution in rock is essential for understanding how the elastic properties of porous rocks affected by their poregeometry. In this study, we revisited a well-studied porous rock, Darley Dale sandstone, which has been studied by different groups with different purposes. Most of them are the deformation experiments. Different from previous studies, we measured the sound velocity of Darley dale sandstone under hydrostatic conditions. Also, we employed different techniques to investigate the pore geometry and porosity of Darley Dale sandstone to gain the insight of velocity changing behavior under the crustal conditions. Here, we measured a fully-dense copper block for a comparison. We performed X-ray CT scanning (XCT) to image the pore space of sandstone to construct the 3-D image of pore geometry, distribution and the pore size. The CT image data are allowed us to estimate the porosity of sandstone, too. One the other hand, the porosity of sample was measured using imbibitions method at ambient conditions and helium porosimeter at high pressure (up to 150 MPa). A set of specimens were cored from Darley Dale sandstone block. P and S wave velocities of specimens were measured at ambient conditions. We also performed high pressure velocity measurements on a selected rock specimen and a copper block up to 150 MPa under dry condition. Porosity of a set of rock specimens measured by imbibitions method was spanned from 6% to 15%, largely distributed within a range of 8%-11%. Compared the porosity obtained from three different techniques, imbibitions method, helium porosimeter and XCT, values from those measurements are in good agreement

Formation factor in Bentheimer and Fontainebleau sandstones: Theory compared with pore-scale numerical simulations

Science.gov (United States)

Ghanbarian, Behzad; Berg, Carl F.

2017-09-01

Accurate quantification of formation resistivity factor F (also called formation factor) provides useful insight into connectivity and pore space topology in fully saturated porous media. In particular the formation factor has been extensively used to estimate permeability in reservoir rocks. One of the widely applied models to estimate F is Archie's law (F = ϕ- m in which ϕ is total porosity and m is cementation exponent) that is known to be valid in rocks with negligible clay content, such as clean sandstones. In this study we compare formation factors determined by percolation and effective-medium theories as well as Archie's law with numerical simulations of electrical resistivity on digital rock models. These digital models represent Bentheimer and Fontainebleau sandstones and are derived either by reconstruction or directly from micro-tomographic images. Results show that the universal quadratic power law from percolation theory accurately estimates the calculated formation factor values in network models over the entire range of porosity. However, it crosses over to the linear scaling from the effective-medium approximation at the porosity of 0.75 in grid models. We also show that the effect of critical porosity, disregarded in Archie's law, is nontrivial, and the Archie model inaccurately estimates the formation factor in low-porosity homogeneous sandstones.

Diagenetic history of the Surma Group sandstones (Miocene) in the Surma Basin, Bangladesh

Science.gov (United States)

Rahman, M. Julleh Jalalur; McCann, Tom

2012-02-01

This study examines the various diagenetic controls of the Miocene Surma Group sandstones encountered in petroleum exploration wells from the Surma Basin, which is situated in the northeastern part of the Bengal Basin, Bangladesh. The principal diagenetic minerals/cements in the Surma Group sandstones are Fe-carbonates (with Fe-calcite dominating), quartz overgrowths and authigenic clays (predominantly chlorite, illite-smectite and minor kaolin). The isotopic composition of the carbonate cement revealed a narrow range of δ 18O values (-10.3‰ to -12.4‰) and a wide range of δ 13C value (+1.4‰ to -23.1‰). The δ 13C VPDB and δ 18O VPDB values of the carbonate cements reveal that carbon was most likely derived from the thermal maturation of organic matter during burial, as well as from the dissolution of isolated carbonate clasts and precipitated from mixed marine-meteoric pore waters. The relationship between the intergranular volume (IGV) versus cement volume indicates that compaction played a more significant role than cementation in destroying the primary porosity. However, cementation also played a major role in drastically reducing porosity and permeability in sandstones with poikilotopic, pore-filling blocky cements formed in early to intermediate and deep burial areas. In addition to Fe-carbonate cements, various clay minerals including illite-smectite and chlorite occur as pore-filling and pore-lining authigenic phases. Significant secondary porosity has been generated at depths from 2500 m to 4728 m. The best reservoir rocks found at depths of 2500-3300 m are well sorted, relatively coarse grained; more loosely packed and better rounded sandstones having good porosities (20-30%) and high permeabilities (12-6000 mD). These good quality reservoir rocks are, however, not uniformly distributed and can be considered to be compartmentalized as a result of interbedding with sandstone layers of low to moderate porosities, low permeabilities owing to poor

Utilization of the St. Peter Sandstone in the Illinois Basin for CO2 Sequestration

Energy Technology Data Exchange (ETDEWEB)

Will, Robert; Smith, Valerie; Leetaru, Hannes

2014-09-30

This project is part of a larger project co-funded by the United States Department of Energy (US DOE) under cooperative agreement DE-FE0002068 from 12/08/2009 through 9/31/2014. The study is to evaluate the potential of formations within the Cambro-Ordovician strata above the Mt. Simon Sandstone as potential targets for carbon dioxide (CO2) sequestration in the Illinois and Michigan Basins. This report evaluates the potential injectivity of the Ordovician St. Peter Sandstone. The evaluation of this formation was accomplished using wireline data, core data, pressure data, and seismic data acquired through funding in this project as well as existing data from two additional, separately funded projects: the US DOE funded Illinois Basin – Decatur Project (IBDP) being conducted by the Midwest Geological Sequestration Consortium (MGSC) in Macon County, Illinois, and the Illinois Industrial Carbon Capture and Sequestration (ICCS) Project funded through the American Recovery and Reinvestment Act (ARRA), which received a phase two award from DOE. This study addresses the question of whether or not the St. Peter Sandstone may serve as a suitable target for CO2 sequestration at locations within the Illinois Basin where it lies at greater depths (below the underground source of drinking water (USDW)) than at the IBDP site. The work performed included numerous improvements to the existing St. Peter reservoir model created in 2010. Model size and spatial resolution were increased resulting in a 3 fold increase in the number of model cells. Seismic data was utilized to inform spatial porosity distribution and an extensive core database was used to develop porosity-permeability relationships. The analysis involved a Base Model representative of the St. Peter at “in-situ” conditions, followed by the creation of two hypothetical models at in-situ + 1,000 feet (ft.) (300 m) and in-situ + 2,000 ft. (600 m) depths through systematic depthdependent adjustment of the Base Model

The effect of grain size and cement content on index properties of weakly solidified artificial sandstones

Science.gov (United States)

Atapour, Hadi; Mortazavi, Ali

2018-04-01

The effects of textural characteristics, especially grain size, on index properties of weakly solidified artificial sandstones are studied. For this purpose, a relatively large number of laboratory tests were carried out on artificial sandstones that were produced in the laboratory. The prepared samples represent fifteen sandstone types consisting of five different median grain sizes and three different cement contents. Indices rock properties including effective porosity, bulk density, point load strength index, and Schmidt hammer values (SHVs) were determined. Experimental results showed that the grain size has significant effects on index properties of weakly solidified sandstones. The porosity of samples is inversely related to the grain size and decreases linearly as grain size increases. While a direct relationship was observed between grain size and dry bulk density, as bulk density increased with increasing median grain size. Furthermore, it was observed that the point load strength index and SHV of samples increased as a result of grain size increase. These observations are indirectly related to the porosity decrease as a function of median grain size.

Local porosity analysis of pore structure in cement paste

International Nuclear Information System (INIS)

Hu Jing; Stroeven, Piet

2005-01-01

Three-dimensional (3-D) local porosity theory (LPT) was originally proposed by Hilfer and recently used for the analysis of pore space geometry in model sandstone. LPT pursues to define the probability density functions of porosity and porosity connectivity. In doing so, heterogeneity differences in various sandstone samples were assessed. However, fundamental issues as to the stochastic concept of geometric heterogeneity are ignored in Hilfer's LPT theory. This paper focuses on proper sampling procedures that should be based on stochastic approaches to multistage sampling and geometric heterogeneity. Standard LPT analysis provides a 3-D microscopic modeling approach to materials. Traditional experimental techniques yield two-dimensional (2-D) section images, however. Therefore, this paper replaces the method for assessing material data in standard LPT theory to a more practical one, based on stereological, 3-D interpretation of quantitative image analysis data. The developed methodology is used to characterize the pore structure in hardened cement paste with various water/cement ratios (w/c) at different hydration stages

Study of the porosity of synthetic sandstones by nondestructive nuclear techniques; Estudo da porosidade de arenitos sinteticos por tecnicas nucleares nao destrutivas

Energy Technology Data Exchange (ETDEWEB)

Marques, Leonardo Carmezini

2008-07-01

In this paper, nuclear techniques have been used to describe structural characteristics of ceramic samples. These samples were produced to serve as simulates of sandstones and their mainly component was silica (SiO{sub 2}). Three sets of these samples with different characteristics were analyzed with the gamma ray transmission and the X-ray microtomography. They had the function to describe parameters as porosity point to point and total average porosity, for the transmission case, and 2D sections average porosity, total average porosity and size porous distribution for microtomography, as well as to investigate possible irregularities in bulk sample. The experimental set up for the gamma ray transmission technique consisted of: a 2 x 2 crystal NaI(Tl) detector, an {sup 241}Am radioactive source (59.54 keV, 100 mCi), an automatic micrometric table for the sample XZ movement and standard gamma spectrometry electronics. Lead collimators with 2 mm diameter were placed on the source way out and on the detector entrance. The microtomographic measurements were done with a Skyscan system, model 1172, with a X-ray tube with 20-100 kV of voltage range and a CCD camera. Employing gamma ray transmission method was possible to obtain overall porosity values from 25.8 to 34.0 % and from 24.8 to 29.2 % for samples with parallelepiped and cylinder shape, respectively, for ceramic I set; from 58.5 to 61.0 % and from 57.1 to 61.7 % for the same geometric shape of ceramic II set. The samples analyzed by the microtomography achieved resolutions of 1.73 {mu}m, 0.64 {mu}m and 1.28 {mu}m for samples of ceramic set I, II and III, respectively. This methodology provided average total porosity values from 26.6 to 29.4 %, from 48.4 to 51.0 % and from 28.2 to 30.6 % to I, II and III ceramic sets, respectively. The porous size profiles of each ceramic sample were also measured. (author)

Physical and chemical properties for sandstone and bentonites

International Nuclear Information System (INIS)

Sato, Haruo

2004-01-01

Physical and chemical properties such as porosity, pore-size distribution, dry density, solid density, mineralogy and chemical composition, which are important parameters for the understanding and analysis of the diffusion phenomena of radionuclides and ions in bentonite and in the geosphere, were measured. The measurements were performed for sandstone, of which fundamental data and information are limited. For bentonite, 3 kinds of bentonites with different smectite contents (Kunigel-V1, Kunipia-F, MX80) were used. In the measurements of the physical and chemical properties of rock, the measurements of solid density by pychnometer, the measurements of porosity, dry density and solid density by water saturation method, the measurements of porosity, dry density, solid density, pore-size distribution and specific surface area of pores by Hg porosimetry, the identifications of constituent minerals by X-ray Diffractometry (XRD), the measurement of chemical composition by whole rock analysis, the observations of micropore structure by Laser Confocal Microscope (LCM), the measurements of water vaporization curves and the measurements of the homogeneity of the rock by penetration of KMnO 4 were performed. While, in the measurements of the physical and chemical properties for bentonite, water basis water content, water content, porosity, dry density, solid density and their distributions in samples were measured, and the degree of inhomogeneity was quantitatively evaluated by comparing with data and information reported up to date. The porosities of sandstone are 15.6±0.21% for water saturation method and 15.5±0.2% for Hg porosimetry, and similar values were obtained in both methods. The solid densities ranged 2.65-2.69 Mg/m 3 for 3 methods, and the average value was 2.668±0.012 Mg/m 3 . The average pore size was 88.8±0.5nm, and pore sizes ≤10μm shared 80% of total pore volume and pore sizes ≤1μm shared 40%. The specific surface area of the pores is 4.09±0.017 m

Support vector regression to predict porosity and permeability: Effect of sample size

Science.gov (United States)

Al-Anazi, A. F.; Gates, I. D.

2012-02-01

Porosity and permeability are key petrophysical parameters obtained from laboratory core analysis. Cores, obtained from drilled wells, are often few in number for most oil and gas fields. Porosity and permeability correlations based on conventional techniques such as linear regression or neural networks trained with core and geophysical logs suffer poor generalization to wells with only geophysical logs. The generalization problem of correlation models often becomes pronounced when the training sample size is small. This is attributed to the underlying assumption that conventional techniques employing the empirical risk minimization (ERM) inductive principle converge asymptotically to the true risk values as the number of samples increases. In small sample size estimation problems, the available training samples must span the complexity of the parameter space so that the model is able both to match the available training samples reasonably well and to generalize to new data. This is achieved using the structural risk minimization (SRM) inductive principle by matching the capability of the model to the available training data. One method that uses SRM is support vector regression (SVR) network. In this research, the capability of SVR to predict porosity and permeability in a heterogeneous sandstone reservoir under the effect of small sample size is evaluated. Particularly, the impact of Vapnik's ɛ-insensitivity loss function and least-modulus loss function on generalization performance was empirically investigated. The results are compared to the multilayer perception (MLP) neural network, a widely used regression method, which operates under the ERM principle. The mean square error and correlation coefficients were used to measure the quality of predictions. The results demonstrate that SVR yields consistently better predictions of the porosity and permeability with small sample size than the MLP method. Also, the performance of SVR depends on both kernel function

Transport of silver nanoparticles in single fractured sandstone

Science.gov (United States)

Neukum, Christoph

2018-02-01

Silver nanoparticles (Ag-NP) are used in various consumer products and are one of the most prevalent metallic nanoparticle in commodities and are released into the environment. Transport behavior of Ag-NP in groundwater is one important aspect for the assessment of environmental impact and protection of drinking water resources in particular. Ag-NP transport processes in saturated single-fractured sandstones using triaxial flow cell experiments with different kind of sandstones is investigated. Ag-NP concentration and size are analyzed using flow field-flow fractionation and coupled SEM-EDX analysis. Results indicate that Ag-NP are more mobile and show generally lower attachment on rock surface compared to experiments in undisturbed sandstone matrix and partially fractured sandstones. Ag-NP transport is controlled by the characteristics of matrix porosity, time depending blocking of attachment sites and solute chemistry. Where Ag-NP attachment occur, it is heterogeneously distributed on the fracture surface.

Effect Of Hot Water Injection On Sandstone Permeability

DEFF Research Database (Denmark)

Rosenbrand, Esther; Fabricius, Ida Lykke

2012-01-01

of published results regarding the effect of temperature on sandstone permeability. These tests are performed with mineral oil, nitrogen gas, distilled water and solutions of NaCl, KCl, CaCl2 as well as brines that contain a mixture of salts. Thirteen sandstone formations, ranging from quartz arenites...... to formations with a significant fraction of fine particles including clay minerals are investigated. The porosities range from 0.10 to 0.30 and permeabilities span the range from 1 to 1000 md. To compare different rock types, specific surface is determined from permeability and porosity using Kozeny’s equation...... not account for all the permeability reductions observed. Permeablity reduction occurs both when distilled water is the saturating fluid as well as in tests with NaCl, KCl or CaCl2 solutions, however, this is not the case in tests with mineral oil or nitrogen gas. The formation of a filter cake or influx...

Electrical conductivity of sandstone, limestone, and granite

Energy Technology Data Exchange (ETDEWEB)

Duba, A.; Piwinskii, A.J.; Santor, M.; Weed, H.C.

1978-01-01

The electrical conductivity of cylindrical cores of Westerly granite, Indiana limestone and Nugget, St Peter and Kayenta sandstones was measured at about 25/sup 0/C in vacuo, in air, and after saturation in distilled water, tap water, and 0.1 M NaCl solution. The three-electrode technique with a guard ring and the two-electrode technique without a guard ring were used. Core aspect ratio over the range of 2.00 to 0.25, as well as frequency over the range of 50 Hz to 10 kHz, influences the conductivity of all rocks, especially those measured in vacuo. Measurements from water-saturated samples using a guard ring are not appreciably different from those obtained without a guard ring. The conductivity of rocks saturated in 0.1 M NaCl solution changes least with a change in aspect ratio; for these rocks a linear relationship, known as Archie's Law, exists between log porosity and log conductivity. No simple correlation was found between those factors in rocks saturated with tap or distilled water. Thus, it appears Archie's Law is of questionable value for correlating laboratory data from rocks saturated with low-conductivity fluids.

An experimental study of the response of the Galesville sandstone to simulated CAES conditions

Energy Technology Data Exchange (ETDEWEB)

Erikson, R L; Stottlemyre, J A; Smith, R P

1980-07-01

The objective of this experimental study was to determine how the mineralogical and physical characteristics of host rock formations are affected by environmental conditions anticipated for compressed air energy storage (CAES) in porous, permeable rock. In this study, Galesville sandstone cores were reacted in autoclave pressure vessels supporting one of four environments: dry air; heated, air-water vapor; heated, nitrogen-water vapor mixtures; and heated, compressed, liquid water. The simulated CAES environments were maintained in autoclave pressure vessels by controlling the following independent variables: temperature, pressure, time, oxygen content, carbon dioxide content, nitrogen content, and liquid volume. The dependent variables studied were: apparent porosity, gas permeability, water permeability, and friability. These variables were measured at ambient temperature and pressure before and after each sandstone sample was reacted in one of the CAES environments. The experiments gave the following results: the Galesville sandstone exhibited excellent stability in dry air at all temperatures tested (50/sup 0/ to 300/sup 0/C); and significant physical alterations occurred in sandstone samples exposed to liquid water above 150/sup 0/C. Samples shielded from dripping water exhibited excellent stability to 300/sup 0/C; sandstone may be a suitable storage media for heated, humid air provided elevated temperature zones are relatively free of mobile liquid water; and observed changes in the physical properties of the rock may have been caused, in part, by the lack of confining stress on the sample. The inability to apply confining pressure is a severe limitation of autoclave experiments.

Single- and two-phase flow simulation based on equivalent pore network extracted from micro-CT images of sandstone core.

Science.gov (United States)

Song, Rui; Liu, Jianjun; Cui, Mengmeng

2016-01-01

Due to the intricate structure of porous rocks, relationships between porosity or saturation and petrophysical transport properties classically used for reservoir evaluation and recovery strategies are either very complex or nonexistent. Thus, the pore network model extracted from the natural porous media is emphasized as a breakthrough to predict the fluid transport properties in the complex micro pore structure. This paper presents a modified method of extracting the equivalent pore network model from the three-dimensional micro computed tomography images based on the maximum ball algorithm. The partition of pore and throat are improved to avoid tremendous memory usage when extracting the equivalent pore network model. The porosity calculated by the extracted pore network model agrees well with the original sandstone sample. Instead of the Poiseuille's law used in the original work, the Lattice-Boltzmann method is employed to simulate the single- and two- phase flow in the extracted pore network. Good agreements are acquired on relative permeability saturation curves of the simulation against the experiment results.

Application of base-level cycles to sandstone-type uranium deposit: taking Dongsheng uranium deposits as an example

International Nuclear Information System (INIS)

Yang Renchao; Han Zuozhen; Fan Aiping; Chang Xiangchun

2006-01-01

High-resolution sequence stratigraphy taking base-level cycles as interface of reference was developed rapidly in recent years. Its greatest predominance lies in that it can be applied to multi-controled continental sedimentary basins and can effectively improve accuracy and distinguishability of sequence stratigraphy analysis. Principles of base-level cycles can also be applied to the research and practice of the exploration and exploitation of sandstone-type uranium deposits as they control the spatial distribution, porosity, the permeability and the sealing ability of sandstone and mudstone, and stacking patterns of strata configuration. Taking Dongsheng uranium deposits as an example, the application of base-level cycles to exploration and exploitation of sandstone uranium deposits was analyzed. It is suggested that favorable strata framework of sandstone and mudstone was developed very well in the fluctuation of base-level cycles. Sand bodies were provided with good connectedness, coarse granularity, high debris content, low matrix content and good porosity-permeability becoming the most important uranium hosted strata. (authors)

Pore network properties of sandstones in a fault damage zone

Science.gov (United States)

Bossennec, Claire; Géraud, Yves; Moretti, Isabelle; Mattioni, Luca; Stemmelen, Didier

2018-05-01

The understanding of fluid flow in faulted sandstones is based on a wide range of techniques. These depend on the multi-method determination of petrological and structural features, porous network properties and both spatial and temporal variations and interactions of these features. The question of the multi-parameter analysis on fluid flow controlling properties is addressed for an outcrop damage zone in the hanging wall of a normal fault zone on the western border of the Upper Rhine Graben, affecting the Buntsandstein Group (Early Triassic). Diagenetic processes may alter the original pore type and geometry in fractured and faulted sandstones. Therefore, these may control the ultimate porosity and permeability of the damage zone. The classical model of evolution of hydraulic properties with distance from the major fault core is nuanced here. The hydraulic behavior of the rock media is better described by a pluri-scale model including: 1) The grain scale, where the hydraulic properties are controlled by sedimentary features, the distance from the fracture, and the impact of diagenetic processes. These result in the ultimate porous network characteristics observed. 2) A larger scale, where the structural position and characteristics (density, connectivity) of the fracture corridors are strongly correlated with both geo-mechanical and hydraulic properties within the damage zone.

Integration of ANFIS, NN and GA to determine core porosity and permeability from conventional well log data

Science.gov (United States)

Ja'fari, Ahmad; Hamidzadeh Moghadam, Rasoul

2012-10-01

Routine core analysis provides useful information for petrophysical study of the hydrocarbon reservoirs. Effective porosity and fluid conductivity (permeability) could be obtained from core analysis in laboratory. Coring hydrocarbon bearing intervals and analysis of obtained cores in laboratory is expensive and time consuming. In this study an improved method to make a quantitative correlation between porosity and permeability obtained from core and conventional well log data by integration of different artificial intelligent systems is proposed. The proposed method combines the results of adaptive neuro-fuzzy inference system (ANFIS) and neural network (NN) algorithms for overall estimation of core data from conventional well log data. These methods multiply the output of each algorithm with a weight factor. Simple averaging and weighted averaging were used for determining the weight factors. In the weighted averaging method the genetic algorithm (GA) is used to determine the weight factors. The overall algorithm was applied in one of SW Iran’s oil fields with two cored wells. One-third of all data were used as the test dataset and the rest of them were used for training the networks. Results show that the output of the GA averaging method provided the best mean square error and also the best correlation coefficient with real core data.

Integration of ANFIS, NN and GA to determine core porosity and permeability from conventional well log data

International Nuclear Information System (INIS)

Ja’fari, Ahmad; Moghadam, Rasoul Hamidzadeh

2012-01-01

Routine core analysis provides useful information for petrophysical study of the hydrocarbon reservoirs. Effective porosity and fluid conductivity (permeability) could be obtained from core analysis in laboratory. Coring hydrocarbon bearing intervals and analysis of obtained cores in laboratory is expensive and time consuming. In this study an improved method to make a quantitative correlation between porosity and permeability obtained from core and conventional well log data by integration of different artificial intelligent systems is proposed. The proposed method combines the results of adaptive neuro-fuzzy inference system (ANFIS) and neural network (NN) algorithms for overall estimation of core data from conventional well log data. These methods multiply the output of each algorithm with a weight factor. Simple averaging and weighted averaging were used for determining the weight factors. In the weighted averaging method the genetic algorithm (GA) is used to determine the weight factors. The overall algorithm was applied in one of SW Iran’s oil fields with two cored wells. One-third of all data were used as the test dataset and the rest of them were used for training the networks. Results show that the output of the GA averaging method provided the best mean square error and also the best correlation coefficient with real core data. (paper)

Electrokinetic desalination of sandstones for NaCl removal

DEFF Research Database (Denmark)

Ottosen, Lisbeth M.; Christensen, Iben V.

2012-01-01

of reliable methods to remove the damaging salts in order to stop the decay. Electrokinetic desalination of fired clay bricks have previously shown efficient in laboratory scale and in the present work the method is tested for desalination of Cotta and Posta sandstones, which both have lower porosity than...... each stone, but electroosmosis in the poultices may have caused suction/pressure over the interface between stone and poultice causing the differences in poultice water content. The transport numbers for Cl− and Na+ differed in the two stones and were highest in the most porous Cotta sandstone in spite...... of similar high pore water concentrations and the same applied electric current. The hypotheses is that a layered structure of the sandstones could be the cause for this, as the electric current may preferentially flow in certain paths through the stone, which are thus desalinated first. After...

Desalination of salt damaged Obernkirchen sandstone by an applied DC field

DEFF Research Database (Denmark)

Matyščák, Ondřej; Ottosen, Lisbeth M.; Rörig-Dalgaard, Inge

2014-01-01

Soluble salts are considered as one of the most common causes for decay of building materials. In the present work, an electrokinetic method for desalination of sandstones from a historic warehouse was tested. The sandstones claddings were removed from the warehouse during a renovation action...... in the stones, i.e. the present investigation faces more challenges relevant to a real desalination action. Experiments were conducted with two Obernkirchen sandstones from the same warehouse, but with different levels of salt concentrations and porosity. The investigation includes removal of the most common...... salts: chlorides, nitrates, sulphates. In the experimental setup the electrodes were placed in a clay poultice: a mixture of kaolinite, calcite and distilled water. An electric direct current (DC) field was applied to the sandstone.By applying 2mA for 5–11days it was possible to reduce the chloride...

Diagenesis, provenance and depositional environments of the Bunter Sandstone Formation

DEFF Research Database (Denmark)

Olivarius, Mette; Weibel, Rikke; Friis, Henrik

The Bunter Sandstone Formation in the northern North German Basin has large geothermal potential with high porosity and permeability (generally >15% and >100 mD, respectively) and with pore fluid temperatures that are adequate for geothermal energy production (c. 55–60˚C). A combined investigation...

Experimental Study and Mathematical Modeling of Asphaltene Deposition Mechanism in Core Samples

Directory of Open Access Journals (Sweden)

Jafari Behbahani T.

2015-11-01

Full Text Available In this work, experimental studies were conducted to determine the effect of asphaltene deposition on the permeability reduction and porosity reduction of carbonate, sandstone and dolomite rock samples using an Iranian bottom hole live oil sample which is close to reservoir conditions, whereas in the majority of previous work, a mixture of recombined oil (a mixture of dead oil and associated gas was injected into a core sample which is far from reservoir conditions. The effect of the oil injection rate on asphaltene deposition and permeability reduction was studied. The experimental results showed that an increase in the oil injection flow rate can result in an increase in asphaltene deposition and permeability reduction. Also, it can be observed that at lower injection flow rates, a monotonic decrease in permeability of the rock samples can be attained upon increasing the injection flow rate, while at higher injection rates, after a decrease in rock permeability, an increasing trend is observed before a steady-state condition can be reached. The experimental results also showed that the rock type can affect the amount of asphaltene deposition, and the asphaltene deposition has different mechanisms in sandstone and carbonate core samples. It can be seen that the adsorption and plugging mechanisms have a more important role in asphaltene deposition in carbonate core samples than sandstone core samples. From the results, it can be observed that the pore volumes of the injected crude oil are higher for sandstone cores compared with the carbonate cores. Also, it can be inferred that three depositional types may take place during the crude oil injection, i.e., continuous deposition for low-permeability cores, slow, steady plugging for high-permeability cores and steady deposition for medium-permeability cores. It can be seen from the experimental results that damage to the core samples was found to increase when the production pressures were

Investigation of porosity and pore structure adjacent to fractures by PMMA method. Samples taken from drill cores at Olkiluoto

International Nuclear Information System (INIS)

Siitari-Kauppi, M.; Ikonen, J.; Kauppi, L.; Lindberg, A.

2010-10-01

The porosity, pore structure and micro fracturing of 18 rock cores from drill holes OLKR4, OL-KR11, OL-KR13, OL-KR14, OL-KR15, OL-KR20 and OL-KR25. The porosity was investigated by the C-14-PMMA autoradiographic method. The main focus was to analyse the changes in porosity and mineralogy adjacent to the typical fractures in the bedrock of Olkiluoto as a mean of porosity profiles. The method makes it possible to study the spatial distribution of the pore space in rock, and the heterogeneity of rock matrices is revealed at the sub micrometre to the centimetre scale. Subsequent autoradiography and digital image analysis make it possible to analyse features limited in size by the range of C-14 beta radiation. The description of the method was given in Posiva working report 2009-03. The samples for this work were chosen in April 2008. The C-14-PMMA method involves the impregnation of centimetre-scale rock cores with C-14 labelled methylmethacrylate (C-14-MMA) in a vacuum, irradiation polymerisation, autoradiography and optical densitometry using digital image-processing techniques. Impregnation with C-14-MMA, a labelled low-molecular-weight and lowviscosity monomer which wets the silicate surfaces well and which can be fixed by polymerisation provides information about the accessible pore space in crystalline rock that cannot be obtained using other methods. The microscopy analyses for mineral identification were done for every PMMA impregnated sample in Geological Survey of Finland. The total porosities of the studied rock cores varied between 0.1 % and 8 %. However, spatially the porosities of 30 - 40 % were determined for the minerals that were strongly altered. The porosity changes were observed adjacent to the fracture surfaces forming from a few to several millimetres porous zones. The heterogeneity of the porosity patterns adjacent to the fracture surfaces was abundant due to mineral alteration. (orig.)

Lack of inhibiting effect of oil emplacement on quartz cementation: Evidence from Cambrian reservoir sandstones, Paleozoic Baltic Basin

DEFF Research Database (Denmark)

Molenaar, Nicolaas; Cyziene, Jolanta; Sliaupa, Saulius

2008-01-01

Currently, the question of whether or not the presence of oil in sandstone inhibits quartz cementation and preserves porosity is still debated. Data from a number of Cambrian sandstone oil fields and dry fields have been studied to determine the effects of oil emplacement on quartz cementation. T...

Study of petrological characteristics of uranium-bearing sandstone in the south of ordos basin, China

International Nuclear Information System (INIS)

Tian Cheng; Jia Licheng; Li Song; Zhang Zimin

2007-01-01

This paper discusses the relation between uranium-bearing abundance and texture constituent of sedimentary rock, on the basis of the research of petrological characteristic of sandstone in the south of Ordos basin. The influence of infiltration of sandstone and uranium migration and accumulation by the major diagenesis of compaction and cementation, clay minerals evolution, corrosion and forming of secondary porosity are discussed. Uranium-bearing sandstones are divided into four types and their petrological characteristics are discussed. After mineralization conditions being summed up, the uranium-mineralization model of sandstone-type is built. Reliable petrological evidences for evaluating favourable uranium mineralization rich areas are furnished. (authors)

Geological Carbon Sequestration Storage Resource Estimates for the Ordovician St. Peter Sandstone, Illinois and Michigan Basins, USA

Energy Technology Data Exchange (ETDEWEB)

Barnes, David; Ellett, Kevin; Leetaru, Hannes

2014-09-30

The Cambro-Ordovician strata of the Midwest of the United States is a primary target for potential geological storage of CO2 in deep saline formations. The objective of this project is to develop a comprehensive evaluation of the Cambro-Ordovician strata in the Illinois and Michigan Basins above the basal Mount Simon Sandstone since the Mount Simon is the subject of other investigations including a demonstration-scale injection at the Illinois Basin Decatur Project. The primary reservoir targets investigated in this study are the middle Ordovician St Peter Sandstone and the late Cambrian to early Ordovician Knox Group carbonates. The topic of this report is a regional-scale evaluation of the geologic storage resource potential of the St Peter Sandstone in both the Illinois and Michigan Basins. Multiple deterministic-based approaches were used in conjunction with the probabilistic-based storage efficiency factors published in the DOE methodology to estimate the carbon storage resource of the formation. Extensive data sets of core analyses and wireline logs were compiled to develop the necessary inputs for volumetric calculations. Results demonstrate how the range in uncertainty of storage resource estimates varies as a function of data availability and quality, and the underlying assumptions used in the different approaches. In the simplest approach, storage resource estimates were calculated from mapping the gross thickness of the formation and applying a single estimate of the effective mean porosity of the formation. Results from this approach led to storage resource estimates ranging from 3.3 to 35.1 Gt in the Michigan Basin, and 1.0 to 11.0 Gt in the Illinois Basin at the P10 and P90 probability level, respectively. The second approach involved consideration of the diagenetic history of the formation throughout the two basins and used depth-dependent functions of porosity to derive a more realistic spatially variable model of porosity rather than applying a

Porosity measurement of amorphous materials by gamma ray transmission

International Nuclear Information System (INIS)

Poettker, Walmir Eno

2000-01-01

In this work it is presented the measurement of the total porosity of TRe soil, Sandstone Berea rocks and porous ceramics samples. For the determination of the total porosity, the Arquimedes method (conventional) and the gamma ray transmission methodology were employed. The porosity measurement using the gamma methodology has a significant advantage respect to the conventional method due to the fast and non-destructive determination, and also for supplying results with a greater characterization in small scales, in relation to the heterogeneity of the porosity. The conventional methodology presents good results only for homogeneous samples. The experimental set up for the gamma ray transmission technique consisted of a 241 Am source (59,53 keV), a NaI (Tl) scintillation detector, collimators, a XYZ, micrometric table and standard gamma spectrometry electronics connected to a multichannel analyser. (author)

Initial porosity of random packing : Computer simulation of grain rearrangement

NARCIS (Netherlands)

Alberts, L.J.H.

2005-01-01

The initial porosity of clastic sediments is poorly defined. In spite of this, it is an important parameter in many models that describe the diagenetic processes taking place during the burial of sediments and which are responsible for the transition from sand to sandstone. Diagenetic models are of

Porosity-depth trends of carbonate deposits along the northwest shelf of Australia (IODP Expedition 356)

Science.gov (United States)

Lee, Eun Young; Kominz, Michelle; Reuning, Lars; Takayanagi, Hideko; Knierzinger, Wolfgang; Wagreich, Michael; Expedition 356 shipboard scientists, IODP

2017-04-01

The northwest shelf (NWS) of Australia extends from northern tropical to southern temperate latitudes situated offshore from the low-moderate-relief and semi-arid Australian continent. The shelf environment is dominated throughout by carbonate sedimentation with warm-water and tropical carbonate deposits, connected to the long-term northward drift of Australia bringing the NWS into tropical latitudes. IODP expedition 356 cored seven sites (U1458-U1464) covering a latitudinal range of 29°S-18°S off the NWS. This study focuses on porosity-depth trends of the Miocene - Pleistocene carbonate sediment on the NWS. The NWS is an ideal area to study regional (and furthermore general) carbonate porosity-depth relationships, because it contains a nearly continuous sequence of carbonate sediment ranging in depth from the surface to about 1,100m and in age from Pleistocene to Miocene. Porosity-depth trends of sedimentary rocks are generally controlled by a variety of factors which govern the rates of porosity loss due to mechanical compaction and of porosity loss (or gain) due to chemical processes during diagenesis. This study derives porosity data from Moisture and Density (MAD) technique conducted during IODP Expedition 356. MAD samples were collected from packstone (44%), wackestone (27%), mudstone (15%) and grainstone (7%), with the rest from floatstone, rudstone, dolostone, sandstone and other subordinate lithologies. To understand porosity-depth trends, the porosity data are arranged both exponentially and linearly, and correlated with age models and lithologic descriptions provided by IODP shipboard scientists. Porosity(%)-depth(m) trends of all the porosity data are Porosity=52e-0.0008/Depth (exponential) and Porosity=-0.03Depth+52 (linear). Porosities near surface and in the deepest parts of each well are least well represented by these trend lines. Porosity values of Pleistocene sediment are generally higher than those of Miocene - Pliocene sediment. The initial

Hydro-geophysical responses to the injection of CO2 in core plugs of Berea sandstone

Science.gov (United States)

Song, I.; Park, K. G.

2017-12-01

We have built a laboratory-scale core flooding system to measure the relative permeability of a core sample and the acoustic response to the CO2 saturation degree at in situ condition of pressure and temperature down to a few kilometer depths. The system consisted of an acoustic velocity core holder (AVC model from the Core Laboratories) between upstream where CO2 and H2O were injected separately and downstream where the mixed fluids came out of a core sample. Core samples with 4 cm in diameter and 5 cm in length of Berea sandstone were in turn placed in the core holder for confining and axial pressures. The flooding operations of the multiphase fluids were conducted through the sample at 40ºC in temperature and 8 MPa in backpressure. CO2 and H2O in the physical condition were injected separately into a sample at constant rate with various ratios. The two phases were mixed during flowing through the sample. The mixed fluids out of the sample were separated again by their different densities in a chamber equipped with a level gauge of the interface. From the level change of the water in the separator, we measured the volume of water coming out of the sample for each test with a constant ratio of the injection rates. Then it was possible to calculate the saturation degree of CO2 from the difference between input volume and output volume of water. The differential pressure between upstream and downstream was directly measured to calculate the relative permeability as a function of the CO2 saturation degree. We also conducted ultrasonic measurements using piezoelectric sensors on the end plugs. An electric pulse was given to a sensor on one end of sample, and then ultrasonic waves were recorded from the other end. The various ratios of injection rate of CO2 and H2O into Berea sandstone yielded a range of 0.1-0.7 in CO2 saturation degree. The relative permeability was obtained at the condition of steady-state flow for given stages from the velocity of each phase and

Permeability in Rotliegend gas sandstones to gas and brine as predicted from NMR, mercury injection and image analysis

DEFF Research Database (Denmark)

Rosenbrand, Esther; Fabricius, Ida Lykke; Fisher, Quentin

2015-01-01

Permeability characterisation of low permeability, clay-rich gas sandstones is part of production forecasting and reservoir management. The physically based Kozeny (1927) equation linking permeability with porosity and pore size is derived for a porous medium with a homogeneous pore size, whereas...... the pore sizes in tight sandstones can range from nm to μm. Nuclear magnetic resonance (NMR) transverse relaxation was used to estimate a pore size distribution for 63 samples of Rotliegend sandstone. The surface relaxation parameter required to relate NMR to pore size is estimated by combination of NMR...

Multinomial Logistic Regression & Bootstrapping for Bayesian Estimation of Vertical Facies Prediction in Heterogeneous Sandstone Reservoirs

Science.gov (United States)

Al-Mudhafar, W. J.

2013-12-01

Precisely prediction of rock facies leads to adequate reservoir characterization by improving the porosity-permeability relationships to estimate the properties in non-cored intervals. It also helps to accurately identify the spatial facies distribution to perform an accurate reservoir model for optimal future reservoir performance. In this paper, the facies estimation has been done through Multinomial logistic regression (MLR) with respect to the well logs and core data in a well in upper sandstone formation of South Rumaila oil field. The entire independent variables are gamma rays, formation density, water saturation, shale volume, log porosity, core porosity, and core permeability. Firstly, Robust Sequential Imputation Algorithm has been considered to impute the missing data. This algorithm starts from a complete subset of the dataset and estimates sequentially the missing values in an incomplete observation by minimizing the determinant of the covariance of the augmented data matrix. Then, the observation is added to the complete data matrix and the algorithm continues with the next observation with missing values. The MLR has been chosen to estimate the maximum likelihood and minimize the standard error for the nonlinear relationships between facies & core and log data. The MLR is used to predict the probabilities of the different possible facies given each independent variable by constructing a linear predictor function having a set of weights that are linearly combined with the independent variables by using a dot product. Beta distribution of facies has been considered as prior knowledge and the resulted predicted probability (posterior) has been estimated from MLR based on Baye's theorem that represents the relationship between predicted probability (posterior) with the conditional probability and the prior knowledge. To assess the statistical accuracy of the model, the bootstrap should be carried out to estimate extra-sample prediction error by randomly

Sub-core permeability and relative permeability characterization with Positron Emission Tomography

Science.gov (United States)

Zahasky, C.; Benson, S. M.

2017-12-01

This study utilizes preclinical micro-Positron Emission Tomography (PET) to image and quantify the transport behavior of pulses of a conservative aqueous radiotracer injected during single and multiphase flow experiments in a Berea sandstone core with axial parallel bedding heterogeneity. The core is discretized into streamtubes, and using the micro-PET data, expressions are derived from spatial moment analysis for calculating sub-core scale tracer flux and pore water velocity. Using the flux and velocity data, it is then possible to calculate porosity and saturation from volumetric flux balance, and calculate permeability and water relative permeability from Darcy's law. Full 3D simulations are then constructed based on this core characterization. Simulation results are compared with experimental results in order to test the assumptions of the simple streamtube model. Errors and limitations of this analysis will be discussed. These new methods of imaging and sub-core permeability and relative permeability measurements enable experimental quantification of transport behavior across scales.

Measurement of the porosity of amorphous materials by gamma ray transmission methodology

International Nuclear Information System (INIS)

Pottker, Walmir Eno; Appoloni, Carlos Roberto

2000-01-01

In this work it is presented the measurement of the total porosity of TRe soil, Sandstone Berea rocks and porous ceramics samples. For the determination of the total porosity, the Arquimedes method (conventional) and the gamma ray transmission methodology were employed. The porosity measurement using the gamma methodology has a significant advantage respect to the conventional method due to the fast and non-destructive determination, and also for supplying results with a greater characterization in small scales, in relation to the heterogeneity of the porosity. The conventional methodology presents good results only for homogeneous samples. The experimental set up for the gamma ray transmission technique consisted of a 241 Am source (59,53 keV ), a NaI(Tl) scintillation detector, collimators, a XYZ micrometric table and standard gamma spectrometry electronics connected to a multichannel analyser. (author)

Microstructure parameters evaluation of Botucatu formation sandstone by X-ray microtomography

Energy Technology Data Exchange (ETDEWEB)

Fernandes, Jaquiel S.; Appoloni, Carlos R.; Marques, Leonardo C., E-mail: jaquielfernandes@yahoo.com.b, E-mail: appoloni@uel.b, E-mail: leocarma@yahoo.com.b [Universidade Estadual de Londrina (UEL), PR (Brazil). Dept. de Fisica. Lab. de Fisica Nuclear Aplicada; Fernandes, Celso P., E-mail: celso@lmpt.ufsc.b [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil). Dept. de Engenharia Mecanica. Lab. de Meios Porosos e Propriedades TermoFisicas (LMPT)

2009-07-01

Microstructural parameters evaluation of reservoir rocks are very important to petroleum industry. This work presents total porosity and pore size distribution measurement of a silicified sandstone sample from the Botucatu formation, collected at municipal district of Faxinal, Parana, Brazil. Porosity and pores size distribution were determined using X-Ray microtomography and imaging techniques. Acquired images had 2.9 mum spatial resolution. 800 2-D images where reconstructed for the microstructure analysis. The determined average porosity was 6.1 +- 2.1 %. 95 % of the porous phase refers to pores with radius ranging from 2.9 to 167.4 mum, presenting the larger frequency (6 %) at 5.9 mum radius. The 3-D volume of the sample was reconstructed and compared with the 3-D model obtained through the autocorrelation functions from the 2-D images analysis. (author)

Multi-scale nitrate transport in a sandstone aquifer system under intensive agriculture

Science.gov (United States)

Paradis, Daniel; Ballard, Jean-Marc; Lefebvre, René; Savard, Martine M.

2018-03-01

Nitrate transport in heterogeneous bedrock aquifers is influenced by mechanisms that operate at different spatial and temporal scales. To understand these mechanisms in a fractured sandstone aquifer with high porosity, a groundwater-flow and nitrate transport model—reproducing multiple hydraulic and chemical targets—was developed to explain the actual nitrate contamination observed in groundwater and surface water in a study area on Prince Edward Island, Canada. Simulations show that nitrate is leached to the aquifer year-round, with 61% coming from untransformed and transformed organic sources originating from fertilizers and manure. This nitrate reaches the more permeable shallow aquifer through fractures in weathered sandstone that represent only 1% of the total porosity (17%). Some of the nitrate reaches the underlying aquifer, which is less active in terms of groundwater flow, but most of it is drained to the main river. The river-water quality is controlled by the nitrate input from the shallow aquifer. Groundwater in the underlying aquifer, which has long residence times, is also largely influenced by the diffusion of nitrate in the porous sandstone matrix. Consequently, following a change of fertilizer application practices, water quality in domestic wells and the river would change rapidly due to the level of nitrate found in fractures, but a lag time of up to 20 years would be necessary to reach a steady level due to diffusion. This demonstrates the importance of understanding nitrate transport mechanisms when designing effective agricultural and water management plans to improve water quality.

Elevated Uranium in Aquifers of the Jacobsville Sandstone

Science.gov (United States)

Sherman, H.; Gierke, J.

2003-12-01

The EPA has announced a new standard for uranium in drinking water of 30 parts per billion (ppb). This maximum contaminant level (MCL) takes effect for community water supplies December 2003. The EPA's ruling has heightened awareness among residential well owners that uranium in drinking water may increase the risk of kidney disease and cancer and has created a need for a quantified, scientific understanding of the occurrence and distribution of uranium isotopes in aquifers. The authors are investigating the occurrence of elevated uranium in northern Michigan aquifers of the Middle Proterozoic Jacobsville sandstone, a red to mottled sequence of sandstones, conglomerates, siltstones and shales deposited as basin fill in the 1.1 Ga Midcontinent rift. Approximately 25% of 300 well water samples tested for isotopic uranium have concentrations above the MCL. Elevated uranium occurrences are distributed throughout the Jacobsville sandstone aquifers stretching across Michigan's Upper Peninsula. However, there is significant variation in well water uranium concentrations (from 0.01 to 190 ppb) and neighboring wells do not necessarily have similar concentrations. The authors are investigating hydrogeologic controls on ground water uranium concentrations in the Jacobsville sandstone, e.g. variations in lithology, mineralogy, groundwater residence time and geochemistry. Approximately 2000' of Jacobsville core from the Amoco St. Amour well was examined in conjunction with the spectral gamma ray log run in the borehole. Spikes in equivalent uranium (eU) concentration from the log are frequently associated with clay and heavy mineral layers in the sandstone core. The lithology and mineralogy of these layers will be determined by analysis of thin sections and x-ray diffraction. A portable spectrometer, model GRS-2000/BL, will be used on the sandstone cliffs along Lake Superior to characterize depositional and lithologic facies of the Jacobsville sandstone in terms of

Integrated geomechanical, petrographical and petrophysical study of the sandstones of the Wajid Group, SW Saudi Arabia

Science.gov (United States)

Benaafi, Mohammed; Hariri, Mustafa; Al-Shaibani, Abdulaziz; Abdullatif, Osman; Makkawi, Mohammed

2018-07-01

The Cambro-Permian siliciclastic succession in southwestern Saudi Arabia is represented by the Wajid Group, which consists mainly of fluvial, shallow marine, aeolian, and glacial sandstones. The Wajid Group comprises the Dibsiyah, Sanamah, Qalibah, Khusayyayn, and Juwayl Formations. It is exposed in the Wadi Al-Dawasir area and extends to Najran City. The sandstones of the Wajid Group serve as groundwater aquifers in the Wadi Al-Dawasir and Najran areas and host hydrocarbon (mainly gas) reservoirs in the Rub' Al-Khali Basin. This study aims to characterize the geomechanical properties (rock strength and Young's modulus) of the sandstones of the Wajid Group using field and experimental techniques. A further objective is to investigate the relationships between the geomechanical properties and the petrographical and petrophysical properties of the studied sandstones. The geomechanical properties of the studied sandstones vary from glacial to non-glacial sandstones, as the glacial sandstones display high values of the geomechanical properties with high variability indices. Four geological factors including grain size, cement content, porosity and permeability were observed as the main controls on the geomechanical behaviour of the studied sandstones except for the Khusayyayn sandstone, where the mineral composition was also important. Significant correlations were observed between the petrographical and petrophysical properties and the geomechanical properties of the glacial sandstones. Predictive models of the geomechanical properties (RN, UCS, and E) were generated using regression analysis to account for the glacial sandstones.

Muddy and dolomitic rip-up clasts in Triassic fluvial sandstones: Origin and impact on potential reservoir properties (Argana Basin, Morocco)

Science.gov (United States)

Henares, Saturnina; Arribas, Jose; Cultrone, Giuseppe; Viseras, Cesar

2016-06-01

The significance of rip-up clasts as sandstone framework grains is frequently neglected in the literature being considered as accessory components in bulk sandstone composition. However, this study highlights the great value of muddy and dolomitic rip-up clast occurrence as: (a) information source about low preservation potential from floodplain deposits and (b) key element controlling host sandstone diagenetic evolution and thus ultimate reservoir quality. High-resolution petrographic analysis on Triassic fluvial sandstones from Argana Basin (T6 and T7/T8 units) highlights the significance of different types of rip-up clasts as intrabasinal framework components of continental sediments from arid climates. On the basis of their composition and ductility, three main types are distinguished: (a) muddy rip-up clasts, (b) dolomitic muddy rip-up clasts and (c) dolomite crystalline rip-up clasts. Spatial distribution of different types is strongly facies-related according to grain size. Origin of rip-up clasts is related to erosion of coeval phreatic dolocretes, in different development stages, and associated muddy floodplain sediments. Cloudy cores with abundant inclusions and clear outer rims of dolomite crystals suggest a first replacive and a subsequent displacive growth, respectively. Dolomite crystals are almost stoichiometric. This composition is very similar to that of early sandstone dolomite cement, supporting phreatic dolocretes as dolomite origin in both situations. Sandstone diagenesis is dominated by mechanical compaction and dolomite cementation. A direct correlation exists between: (1) muddy rip-up clast abundance and early reduction of primary porosity by compaction with irreversible loss of intergranular volume (IGV); and (2) occurrence of dolomitic rip-up clasts and dolomite cement nucleation in host sandstone, occluding adjacent pores but preserving IGV. Both processes affect reservoir quality by generation of vertical and 3D fluid flow baffles and

Simulation of forced convection in non-Newtonian fluid through sandstones

Science.gov (United States)

Gokhale, M. Y.; Fernandes, Ignatius

2017-11-01

Numerical simulation is carried out to study forced convection in non-Newtonian fluids flowing through sandstones. Simulation is carried out using lattice Boltzmann method (LBM) for both shear-thinning and shear-thickening, by varying the power law index from 0.5 to 1.5 in Carreau-Yasuda model. Parameters involved in LBM and Carreau model are identified to achieve numerical convergence. Permeability and porosity are varied in the range of 10-10-10-6 and 0.1-0.7, respectively, to match actual geometrical properties of sandstone. Numerical technology is validated by establishing Darcy's law by plotting the graph between velocity and pressure gradient. Consequently, investigation is carried out to study the influence of material properties of porous media on flow properties such as velocity profiles, temperature profiles, and Nusselt number.

Experimental deformation in sandstone, carbonates and quartz aggregate

Energy Technology Data Exchange (ETDEWEB)

Cheung, Cecilia See Nga [Stony Brook Univ., NY (United States)

2015-05-01

The first part of my thesis is mainly focused on the effect of grain size distribution on compaction localization in porous sandstone. To identify the microstructural parameters that influence compaction band formation, I conducted a systematic study of mechanical deformation, failure mode and microstructural evolution in Bleurswiller and Boise sandstones, of similar porosity (~25%) and mineralogy but different sorting. Discrete compaction bands were observed to develop over a wide range of pressure in the Bleurswiller sandstone that has a relatively uniform grain size distribution. In contrast, compaction localization was not observed in the poorly sorted Boise sandstone. My results demonstrate that grain size distribution exerts important influence on compaction band development, in agreement with recently published data from Valley of Fire and Buckskin Gulch, as well as numerical studies. The second part aimed to improve current knowledge on inelastic behavior, failure mode and brittle-ductile transition in another sedimentary rock, porous carbonates. A micritic Tavel (porosity of ~13%) and an allochemical Indiana (~18%) limestones were deformed under compaction in wet and dry conditions. At lower confining pressures, shear localization occurred in brittle faulting regime. Through transitional regime, the deformation switched to cataclastic flow regime at higher confining pressure. Specifically in the cataclastic regime, the (dry and wet) Tavel and dry Indiana failed by distributed cataclastic flow, while in contrast, wet Indiana failed as compaction localization. My results demonstrate that different failure modes and mechanical behaviors under different deformation regimes and water saturation are fundamental prior to any geophysical application in porous carbonates. The third part aimed to focus on investigating compaction on quartz aggregate starting at low (MPa) using X-ray diffraction. We report the diffraction peak evolution of quartz with increasing

Strength curves for shales and sandstones under hydrostatic confining pressures

International Nuclear Information System (INIS)

Gupta, S.C.; Sikka, S.K.

1978-01-01

The experimental data for the effect of confining pressures on the fracture stress have been analysed for shales and sandstones. The normalized compressive strengths are found to lie in a narrow region so that Ohnaka's equation for crystalline rocks, can be fitted to the data. The fitted parameters are physically reasonable and indicate that the functional dependence of strength on porosity, strain rate and temperature is independent of the confining pressures. (author)

Core Flooding Experiments and Reactive Transport Modeling of Seasonal Heat Storage in the Hot Deep Gassum Sandstone Formation

DEFF Research Database (Denmark)

Holmslykke, Hanne D.; Kjøller, Claus; Fabricius, Ida Lykke

2017-01-01

Seasonal storage of excess heat in hot deep aquifers is considered to optimize the usage of commonly available energy sources. The chemical effects of heating the Gassum Sandstone Formation to up to 150 degrees C is investigated by combining laboratory core flooding experiments with petrographic...... analysis and geochemical modeling. Synthetic formation water is injected into two sets of Gassum Formation samples at 25, 50 (reservoir temperature), 100, and 150 degrees C with a velocity of 0.05 and 0.1 PV/h, respectively. Results show a significant increase in the aqueous concentration of silicium...

On the origin of calcite-cemented sandstones in the clearwater formation oil-sands, Alberta

Energy Technology Data Exchange (ETDEWEB)

Colquhoun, I.M.

1999-01-01

This thesis examined the formation of calcite-cemented sandstones in the Clearwater Formation within the Cold Lake and southern Primrose areas of the Alberta oil sands. Three stages of diagenesis have been recognized, both in the calcite-cemented sandstones and reservoir sands. Diagenesis of the Clearwater Formation in the Cold Lake and southern Primrose areas ended once the reservoir filled with hydrocarbons, but in the Cold Lake area, diagenesis of water-saturated sands likely continued after hydrocarbon emplacement. The reservoir sands in the formation contain a diverse clay mineral assemblage. In general, 0.7 nm clays dominate the diagenetic clay mineralogy of the Clearwater sands. Reservoir sands that contain large amounts of detrital clays and early diagenetic, grain-coating chlorite/smectite have significantly reduced bitumen-saturation. The presence of detrital and diagenetic smectitic clays complicates the removal of bitumen from the Clearwater formation using cyclic steam stimulation techniques because they swell during steam stimulation and reduce porosity and permeability of reservoir sands. Reservoir sands that contain kaolinite, feldspar and calcite react to form smectitic clays, which swell upon cyclic steam stimulation and further reduce porosity and permeability of reservoir sands. However, in the Cold Lake and Primrose areas, the dominant clay mineral is berthierine, which is associated with high calcite, which help to preserve porosity, permeability and bitumen saturation. The porous nature of bitumen-saturated, calcite-cemented sandstones that are laterally extensive could possibly provide a preferential path for steam to initiate calcite dissolution and produce significant concentrations of dissolved carbon dioxide in injected fluids. It was noted that this may then precipitate as carbonate scale within the reservoir and could cause formation damage or affect production equipment. 207 refs., 9 tabs., 58 figs., 3 appendices.

The experimental modeling of gas percolation mechanisms in a coal-measure tight sandstone reservoir: A case study on the coal-measure tight sandstone gas in the Upper Triassic Xujiahe Formation, Sichuan Basin, China

Directory of Open Access Journals (Sweden)

Shizhen Tao

2016-12-01

Full Text Available Tight sandstone gas from coal-measure source rock is widespread in China, and it is represented by the Xujiahe Formation of the Sichuan Basin and the Upper Paleozoic of the Ordos Basin. It is affected by planar evaporative hydrocarbon expulsion of coal-measure source rock and the gentle structural background; hydrodynamics and buoyancy play a limited role in the gas migration-accumulation in tight sandstone. Under the conditions of low permeability and speed, non-Darcy flow is quite apparent, it gives rise to gas-water mixed gas zone. In the gas displacing water experiment, the shape of percolation flow curve is mainly influenced by core permeability. The lower the permeability, the higher the starting pressure gradient as well as the more evident the non-Darcy phenomenon will be. In the gas displacing water experiment of tight sandstone, the maximum gas saturation of the core is generally less than 50% (ranging from 30% to 40% and averaging at 38%; it is similar to the actual gas saturation of the gas zone in the subsurface core. The gas saturation and permeability of the core have a logarithm correlation with a correlation coefficient of 0.8915. In the single-phase flow of tight sandstone gas, low-velocity non-Darcy percolation is apparent; the initial flow velocity (Vd exists due to the slippage effect of gas flow. The shape of percolation flow curve of a single-phase gas is primarily controlled by core permeability and confining pressure; the lower the permeability or the higher the confining pressure, the higher the starting pressure (0.02–0.08 MPa/cm, whereas, the higher the quasi-initial flow speed, the longer the nonlinear section and the more obvious the non-Darcy flow will be. The tight sandstone gas seepage mechanism study shows that the lower the reservoir permeability, the higher the starting pressure and the slower the flow velocity will be, this results in the low efficiency of natural gas migration and accumulation as well as

Support vector regression for porosity prediction in a heterogeneous reservoir: A comparative study

Science.gov (United States)

Al-Anazi, A. F.; Gates, I. D.

2010-12-01

In wells with limited log and core data, porosity, a fundamental and essential property to characterize reservoirs, is challenging to estimate by conventional statistical methods from offset well log and core data in heterogeneous formations. Beyond simple regression, neural networks have been used to develop more accurate porosity correlations. Unfortunately, neural network-based correlations have limited generalization ability and global correlations for a field are usually less accurate compared to local correlations for a sub-region of the reservoir. In this paper, support vector machines are explored as an intelligent technique to correlate porosity to well log data. Recently, support vector regression (SVR), based on the statistical learning theory, have been proposed as a new intelligence technique for both prediction and classification tasks. The underlying formulation of support vector machines embodies the structural risk minimization (SRM) principle which has been shown to be superior to the traditional empirical risk minimization (ERM) principle employed by conventional neural networks and classical statistical methods. This new formulation uses margin-based loss functions to control model complexity independently of the dimensionality of the input space, and kernel functions to project the estimation problem to a higher dimensional space, which enables the solution of more complex nonlinear problem optimization methods to exist for a globally optimal solution. SRM minimizes an upper bound on the expected risk using a margin-based loss function ( ɛ-insensitivity loss function for regression) in contrast to ERM which minimizes the error on the training data. Unlike classical learning methods, SRM, indexed by margin-based loss function, can also control model complexity independent of dimensionality. The SRM inductive principle is designed for statistical estimation with finite data where the ERM inductive principle provides the optimal solution (the

Investigated Miscible CO2 Flooding for Enhancing Oil Recovery in Wettability Altered Chalk and Sandstone Rocks

Energy Technology Data Exchange (ETDEWEB)

Tabrizy, Vahid Alipour

2012-07-01

The thesis addresses oil recovery by miscible CO2 flooding from modified sandstone and chalk rocks. Calcite mineral surface is modified with stearic acid (SA) and asphaltene, and the silicate mineral surfaces are modified with N,N-dimethyldodecylamine (NN-DMDA) and asphaltene. The stability of adsorbed polar components in presence of SO4 2- and Mg2 + ions is also investigated. Recovery from sandstone cores is consistently lower than that from chalk cores saturated with the same oil and flooded with CO2 at all miscible flooding conditions. This may be due to the larger permeability contrasts in sandstone cores, which promote the fingering phenomenon. Miscible CO2 flooding for chalk and sandstone cores with distilled water, as initial water saturation, shows also lower oil recovery than cores saturated with different ions. At higher miscible flooding conditions, higher oil recovery is obtained. However, presence of light components (such as C1 or C3) in oil reduced the recovery. Oil recovery in presence of methane (C1) is lower than that in presence of methane and propane (C1/C3). A ternary diagram was constructed in order to understand the CO2 flooding mechanism(s) at the different flooding conditions and in presence of light components. The side effect of the flooding with CO2 is the probability for asphaltene deposition. An approach based on solubility parameter in the liquid, is used to assess the risk for asphaltene deposition during CO2 miscible flooding. The light components (C1/C3) and higher flooding conditions enhanced the risk for asphaltene instability. It is also shown higher amount of asphaltene deposition in chalk cores than that in sandstone cores at similar miscibility conditions.(au)

Performance of Different Acids on Sandstone Formations

Directory of Open Access Journals (Sweden)

M. A. Zaman

2013-12-01

Full Text Available Stimulation of sandstone formations is a challenging task, which involves several chemicals and physical interactions of the acid with the formation. Some of these reactions may result in formation damage. Mud acid has been successfully used to stimulate sandstone reservoirs for a number of years. It is a mixture of hydrofluoric (HF and hydrochloric (HCl acids designed to dissolve clays and siliceous fines accumulated in the near-wellbore region. Matrix acidizing may also be used to increase formation permeability in undamaged wells. The change may be up to 50% to 100% with the mud acid. For any acidizing process, the selection of acid (Formulation and Concentration and the design (Pre-flush, Main Acid, After-flush is very important. Different researchers are using different combinations of acids with different concentrations to get the best results for acidization. Mainly the common practice is combination of Hydrochloric Acid – Hydrofluoric with Concentration (3% HF – 12% HCl. This paper presents the results of a laboratory investigation of Orthophosphoric acid instead of hydrochloric acid in one combination and the second combination is Fluoboric and formic acid and the third one is formic and hydrofluoric acid. The results are compared with the mud acid and the results calculated are porosity, permeability, and FESEM Analysis and Strength tests. All of these new combinations shows that these have the potential to be used as acidizing acids on sandstone formations.

Experimental Investigation on Hydraulic Properties of Granular Sandstone and Mudstone Mixtures

Directory of Open Access Journals (Sweden)

Dan Ma

2018-01-01

Full Text Available The caved zone during longwall mining has high permeability, resulting in a mass of groundwater storage which causes a threat of groundwater inrush hazard to the safe mining. To investigate the hazard mechanism of granular sandstone and mudstone mixture (SMM in caved zone, this paper presents an experimental study on the effect of sandstone particle (SP and mudstone particle (MP weight ratio on the non-Darcy hydraulic properties evolution. A self-designed granular rock seepage experimental equipment has been applied to conduct the experiments. The variation of particle size distribution was induced by loading and water seepage during the test, which indicated that the particle crushing and erosion properties of mudstone were higher than those of sandstone. Porosity evolution of SMM was strongly influenced by loading (sample height and SP/MP weight ratio. The sample with higher sample height and higher weight ratio of SP achieved higher porosity value. In particular, a non-Darcy equation, for hydraulic properties (permeability κ and non-Darcy coefficient ζ calculation, was sufficient to fit the relation between the hydraulic gradient and seepage velocity. The test results indicated that, due to the absence and narrowing of fracture and void during loading, the permeability κ decreases and the non-Darcy coefficient ζ increases. The variation of the hydraulic properties of the sample within the same particle size and SP/MP weight ratio indicated that groundwater inrush hazard showed a higher probability of occurrence in sandstone strata and crushed zone (e.g., faults. Moreover, isolated fractures and voids were able to achieve the changeover from self-extension to interconnection at the last loading stage, which caused the fluctuation tendency of κ and ζ. Fluctuation ability in mudstone was higher than that in sandstone. The performance of an empirical model was also investigated for the non-Darcy hydraulic properties evolution prediction of

Modelling of a diffusion-sorption experiment on sandstone

International Nuclear Information System (INIS)

Smith, P.A.

1989-11-01

The results of a diffusion-sorption experiment on a sample of Darley Dale sandstone, using simulated groundwater spiked with a mixture of 125 I, 85 Sr and 137 Cs, are modelled by a one-dimensional porous medium approach in which sorption is described by Freundlich isotherms. The governing equations are solved analytically for the special case of a linear isotherm, and numerically using the computer code RANCHDIFF for non-linear isotherms. A set of time-dependent, ordinary differential equations is obtained using the Lagrange interpolation technique and integrated by Gear's variable order predictor-corrector method. It is shown that the sorption behaviour of 85 Sr can be modelled successfully by a linear isotherm, using a sorption parameter consistent with batch-sorption tests. The behaviour of 137 Cs may be modelled by a non-linear isotherm, but the amount of 137 Cs sorbed is less than that anticipated from batch-sorption tests. 125 I is assumed to be non-sorbing and is used to determine the porosity of the sandstone. (author) 10 figs., 4 tabs., 6 refs

Wettability Alteration of Sandstone and Carbonate Rocks by Using ZnO Nanoparticles in Heavy Oil Reservoirs

Directory of Open Access Journals (Sweden)

Masoumeh Tajmiri

2015-10-01

Full Text Available Efforts to enhance oil recovery through wettability alteration by nanoparticles have been attracted in recent years. However, many basic questions have been ambiguous up until now. Nanoparticles penetrate into pore volume of porous media, stick on the core surface, and by creating homogeneous water-wet area, cause to alter wettability. This work introduces the new concept of adding ZnO nanoparticles by an experimental work on wettability alteration and oil recovery through spontaneous imbibition mechanism. Laboratory tests were conducted in two experimental steps on four cylindrical core samples (three sandstones and one carbonate taken from a real Iranian heavy oil reservoir in Amott cell. In the first step, the core samples were saturated by crude oil. Next, the core samples were flooded with nanoparticles and saturated by crude oil for about two weeks. Then, the core samples were immersed in distilled water and the amount of recovery was monitored during 30 days for both steps. The experimental results showed that oil recovery for three sandstone cores changed from 20.74, 4.3, and 3.5% of original oil in place (OOIP in the absence of nanoparticles to 36.2, 17.57, and 20.68% of OOIP when nanoparticles were added respectively. Moreover, for the carbonate core, the recovery changed from zero to 8.89% of OOIP by adding nanoparticles. By the investigation of relative permeability curves, it was found that by adding ZnO nanoparticles, the crossover-point of curves shifted to the right for both sandstone and carbonate cores, which meant wettability was altered to water- wet. This study, for the first time, illustrated the remarkable role of ZnO nanoparticles in wettability alteration toward more water-wet for both sandstone and carbonate cores and enhancing oil recovery.

Structural-Diagenetic Controls on Fracture Opening in Tight Gas Sandstone Reservoirs, Alberta Foothills

Science.gov (United States)

Ukar, Estibalitz; Eichhubl, Peter; Fall, Andras; Hooker, John

2013-04-01

In tight gas reservoirs, understanding the characteristics, orientation and distribution of natural open fractures, and how these relate to the structural and stratigraphic setting are important for exploration and production. Outcrops provide the opportunity to sample fracture characteristics that would otherwise be unknown due to the limitations of sampling by cores and well logs. However, fractures in exhumed outcrops may not be representative of fractures in the reservoir because of differences in burial and exhumation history. Appropriate outcrop analogs of producing reservoirs with comparable geologic history, structural setting, fracture networks, and diagenetic attributes are desirable but rare. The Jurassic to Lower Cretaceous Nikanassin Formation from the Alberta Foothills produces gas at commercial rates where it contains a network of open fractures. Fractures from outcrops have the same diagenetic attributes as those observed in cores fractures relative to fold cores, hinges and limbs, 2) compare the distribution and attributes of fractures in outcrop vs. core samples, 3) estimate the timing of fracture formation relative to the evolution of the fold-and-thrust belt, and 4) estimate the degradation of fracture porosity due to postkinematic cementation. Cathodoluminescence images of cemented fractures in both outcrop and core samples reveal several generations of quartz and ankerite cement that is synkinematic and postkinematic relative to fracture opening. Crack-seal textures in synkinematic quartz are ubiquitous, and well-developed cement bridges abundant. Fracture porosity may be preserved in fractures wider than ~100 microns. 1-D scanlines in outcrop and core samples indicate fractures are most abundant within small parasitic folds within larger, tight, mesoscopic folds. Fracture intensity is lower away from parasitic folds; intensity progressively decreases from the faulted cores of mesoscopic folds to their forelimbs, with lowest intensities within

Diagenesis and reservoir quality of Bhuban sandstones (Neogene), Titas Gas Field, Bengal Basin, Bangladesh

Science.gov (United States)

Aminul Islam, M.

2009-06-01

This study deals with the diagenesis and reservoir quality of sandstones of the Bhuban Formation located at the Titas Gas Field of Bengal Basin. Petrographic study including XRD, CL, SEM and BSE image analysis and quantitative determination of reservoir properties were carried out for this study. The sandstones are fine to medium-grained, moderately well to well sorted subfeldspathic arenites with subordinate feldspathic and lithic arenites. The diagenetic processes include clay infiltration, compaction and cementation (quartz overgrowth, chlorite, kaolinite, calcite and minor amount of pyrite, dolomite and K-feldspar overgrowth). Quartz is the dominant pore occluding cement and generally occurred as small euhedral crystals, locally as large pyramidal crystals in the primary pores. Pressure solution derived from grain contact is the main contributor of quartz overgrowths. Chlorite occurs as pore-lining and pore filling cement. In some cases, chlorite helps to retain porosity by preventing quartz overgrowth. In some restricted depth interval, pore-occlusion by calcite cement is very much intense. Kaolinite locally developed as vermiform and accelerated the minor porosity loss due to pore-occlusion. Kaolinite/chlorite enhances ineffective microporosity. Kaolinite is a by-product of feldspar leaching in the presence of acidic fluid produced during the maturation of organic matter in the adjacent Miocene or deeper Oligocene source rocks. The relation between diagenesis and reservoir quality is as follows: the initial porosity was decreased by compaction and cementation and then increased by leaching of the metastable grains and dissolution of cement. Good quality reservoir rocks were deposited in fluvial environment and hence quality of reservoir rocks is also environment selective. Porosity and permeability data exhibit good inverse correlation with cement. However, some data points indicate multiple controls on permeability. Reservoir quality is thus controlled by

Hydrophobization by Means of Nanotechnology on Greek Sandstones Used as Building Facades

Directory of Open Access Journals (Sweden)

Georgios Karagiannis

2013-01-01

Full Text Available Modern sustainable architecture indicates the use of local natural stones for building. Greek sandstones from Epirus (Demati, Greece, EN 12440 used as building facades meet aesthetic and have high mechanical properties, but the inevitable interaction between stone materials and natural or anthropogenic weathering factors controls the type, and extent of stone damages. In the present paper, samples of sandstone were treated with a conventional hydrophobic product and four solutions of the same product, enriched with nanosilica of different concentrations. The properties of the treated samples, such as porosity and pore size distribution, microstructure, static contact angle of a water droplet, and durability to deterioration cycles (freeze-thaw were recorded and conclusions were drawn. The research indicates the increased hydrophobic properties in nanosilica solutions but also the optimum content in nanoparticles that provides hydrophobicity without altering the properties of the stone.

Reservoir Characterization of Bridgeport and Cypress Sandstones in Lawrence Field Illinois to Improve Petroleum Recovery by Alkaline-Surfactant-Polymer Flood

Energy Technology Data Exchange (ETDEWEB)

Seyler, Beverly; Grube, John; Huff, Bryan; Webb, Nathan; Damico, James; Blakley, Curt; Madhavan, Vineeth; Johanek, Philip; Frailey, Scott

2012-12-21

were used to better understand porosity and permeability trends in the region and to characterize barriers and define flow units. Diagenetic alterations that impact porosity and permeability include development of quartz overgrowths, sutured quartz grains, dissolution of feldspar grains, formation of clay mineral coatings on grains, and calcite cementation. Many of these alterations are controlled by facies. Mapping efforts identified distinct flow units in the northern part of the field showing that the Pennsylvanian Bridgeport consists of a series of thick incised channel fill sequences. The sandstones are about 75-150 feet thick and typically consist of medium grained and poorly sorted fluvial to distributary channel fill deposits at the base. The sandstones become indistinctly bedded distributary channel deposits in the main part of the reservoir before fining upwards and becoming more tidally influenced near their top. These channel deposits have core permeabilities ranging from 20 md to well over 1000 md. The tidally influenced deposits are more compartmentalized compared to the thicker and more continuous basal fluvial deposits. Fine grained sandstones that are laterally equivalent to the thicker channel type deposits have permeabilities rarely reaching above 250 md. Most of the unrecovered oil in Lawrence Field is contained in Pennsylvanian Age Bridgeport sandstones and Mississippian Age Cypress sandstones. These reservoirs are highly complex and compartmentalized. Detailed reservoir characterization including the development of 3-D geologic and geocellular models of target areas in the field were completed to identify areas with the best potential to recover remaining reserves including unswept and by-passed oil. This project consisted of tasks designed to compile, interpret, and analyze the data required to conduct reservoir characterization for the Bridgeport and Cypress sandstones in pilot areas in anticipation of expanded implementation of ASP flooding in

NMR Pore Structure and Dynamic Characteristics of Sandstone Caused by Ambient Freeze-Thaw Action

Directory of Open Access Journals (Sweden)

Bo Ke

2017-01-01

Full Text Available For a deeper understanding of the freeze-thaw weathering effects on the microstructure evolution and deterioration of dynamic mechanical properties of rock, the present paper conducted the nuclear magnetic resonance (NMR tests and impact loading experiments on sandstone under different freeze-thaw cycles. The results of NMR test show that, with the increase of freeze-thaw cycles, the pores expand and pores size tends to be uniform. The experimental results show that the stress-strain curves all go through four stages, namely, densification, elasticity, yielding, and failure. The densification curve is shorter, and the slope of elasticity curve decreases as the freeze-thaw cycles increase. With increasing freeze-thaw cycles, the dynamic peak stress decreases and energy absorption of sandstone increases. The dynamic failure form is an axial splitting failure, and the fragments increase and the size diminishes with increasing freeze-thaw cycles. The higher the porosity is, the more severe the degradation of dynamic characteristics is. An increase model for the relationships between the porosity or energy absorption and freeze-thaw cycles number was built to reveal the increasing trend with the freeze-thaw cycles increase; meanwhile, a decay model was built to predict the dynamic compressive strength degradation of rock after repeated freeze-thaw cycles.

Facies architecture of the Bluejacket Sandstone in the Eufaula Lake area, Oklahoma: Implications for the reservoir characterization of the Bartlesville Sandstone

Energy Technology Data Exchange (ETDEWEB)

Ye, Liangmiao; Yang, Kexian [Univ. of Tulsa, OK (United States)

1997-08-01

Outcrop studies of the Bluejacket Sandstone (Middle Pennsylvanian) provide significant insights to reservoir architecture of the subsurface equivalent Bartlesville Sandstone. Quarry walls and road cuts in the Lake Eufaula area offer excellent exposures for detailed facies architectural investigations using high-precision surveying, photo mosaics. Directional minipermeameter measurements are being conducted. Subsurface studies include conventional logs, borehole image log, and core data. Reservoir architectures are reconstructed in four hierarchical levels: multi-storey sandstone, i.e. discrete genetic intervals; individual discrete genetic interval; facies within a discrete genetic interval; and lateral accretion bar deposits. In both outcrop and subsurface, the Bluejacket (Bartlesville) Sandstone comprises two distinctive architectures: a lower braided fluvial and an upper meandering fluvial. Braided fluvial deposits are typically 30 to 80 ft thick, and are laterally persistent filling an incised valley wider than the largest producing fields. The lower contact is irregular with local relief of 50 ft. The braided-fluvial deposits consist of 100-400-ft wide, 5-15-ft thick channel-fill elements. Each channel-fill interval is limited laterally by an erosional contact or overbank deposits, and is separated vertically by discontinuous mudstones or highly concentrated mudstone interclast lag conglomerates. Low-angle parallel-stratified or trough cross-stratified medium- to coarse-grained sandstones volumetrically dominate. This section has a blocky well log profile. Meandering fluvial deposits are typically 100 to 150 ft thick and comprise multiple discrete genetic intervals.

CO2 Storage Potential of the Eocene Tay Sandstone, Central North Sea, UK

Science.gov (United States)

Gent, Christopher; Williams, John

2017-04-01

Carbon Capture and Storage (CCS) is crucial for low-carbon industry, climate mitigation and a sustainable energy future. The offshore capacity of the UK is substantial and has been estimated at 78 Gt of CO2 in saline aquifers and hydrocarbon fields. The early-mid Eocene Tay Sandstone Member of the Central North Sea (CNS) is a submarine-fan system and potential storage reservoir with a theoretical capacity of 123 Mt of CO2. The Tay Sandstone comprises of 4 sequences, amalgamating into a fan complex 125km long and 40 km at a minimum of 1500 m depth striking NW-SE, hosting several hydrocarbon fields including Gannett A, B, D and Pict. In order to better understand the storage potential and characteristics, the Tay Sandstone over Quadrant 21 has been interpreted using log correlation and 3D seismic. Understanding the internal and external geometry of the sandstone as well as the lateral extent of the unit is essential when considering CO2 vertical and horizontal fluid flow pathways and storage security. 3D seismic mapping of a clear mounded feature has revealed the youngest sequence of the Tay complex; a homogenous sand-rich channel 12 km long, 1.5 km wide and on average 100 m thick. The sandstone has porosity >35%, permeability >5 D and a net to gross of 0.8, giving a total pore volume of 927x106 m3. The remaining three sequences are a series of stacked channels and interbedded mudstones which are more quiescent on the seismic, however, well logs indicate each subsequent sequence reduce in net to gross with age as mud has a greater influence in the early fan system. Nevertheless, the sandstone properties remain relatively consistent and are far more laterally extensive than the youngest sequence. The Tay Sandstone spatially overlaps several other potential storage sites including the older Tertiary sandstones of the Cromarty, Forties and Mey Members and deeper Jurassic reservoirs. This favours the Tay Sandstone to be considered in a secondary or multiple stacked

Experimental study and theoretical interpretation of saturation effect on ultrasonic velocity in tight sandstones under different pressure conditions

Science.gov (United States)

Li, Dongqing; Wei, Jianxin; Di, Bangrang; Ding, Pinbo; Huang, Shiqi; Shuai, Da

2018-03-01

Understanding the influence of lithology, porosity, permeability, pore structure, fluid content and fluid distribution on the elastic wave properties of porous rocks is of great significance for seismic exploration. However, unlike conventional sandstones, the petrophysical characteristics of tight sandstones are more complex and less understood. To address this problem, we measured ultrasonic velocity in partially saturated tight sandstones under different effective pressures. A new model is proposed, combining the Mavko-Jizba-Gurevich relations and the White model. The proposed model can satisfactorily simulate and explain the saturation dependence and pressure dependence of velocity in tight sandstones. Under low effective pressure, the relationship of P-wave velocity to saturation is pre-dominantly attributed to local (pore scale) fluid flow and inhomogeneous pore-fluid distribution (large scale). At higher effective pressure, local fluid flow gradually decreases, and P-wave velocity gradually shifts from uniform saturation towards patchy saturation. We also find that shear modulus is more sensitive to saturation at low effective pressures. The new model includes wetting ratio, an adjustable parameter that is closely related to the relationship between shear modulus and saturation.

Flow units classification for geostatisitical three-dimensional modeling of a non-marine sandstone reservoir: A case study from the Paleocene Funing Formation of the Gaoji Oilfield, east China

Science.gov (United States)

Zhang, Penghui; Zhang, Jinliang; Wang, Jinkai; Li, Ming; Liang, Jie; Wu, Yingli

2018-05-01

Flow units classification can be used in reservoir characterization. In addition, characterizing the reservoir interval into flow units is an effective way to simulate the reservoir. Paraflow units (PFUs), the second level of flow units, are used to estimate the spatial distribution of continental clastic reservoirs at the detailed reservoir description stage. In this study, we investigate a nonroutine methodology to predict the external and internal distribution of PFUs. The methodology outlined enables the classification of PFUs using sandstone core samples and log data. The relationships obtained between porosity, permeability and pore throat aperture radii (r35) values were established for core and log data obtained from 26 wells from the Funing Formation, Gaoji Oilfield, Subei Basin, China. The present study refines predicted PFUs at logged (0.125-m) intervals, whose scale is much smaller than routine methods. Meanwhile, three-dimensional models are built using sequential indicator simulation to characterize PFUs in wells. Four distinct PFUs are classified and located based on the statistical methodology of cluster analysis, and each PFU has different seepage ability. The results of this study demonstrate the obtained models are able to quantify reservoir heterogeneity. Due to different petrophysical characteristics and seepage ability, PFUs have a significant impact on the distribution of the remaining oil. Considering these allows a more accurate understanding of reservoir quality, especially within non-marine sandstone reservoirs.

The influence of clay minerals on acoustic properties of sandstones

Energy Technology Data Exchange (ETDEWEB)

Hansen, Olav

1997-12-31

This thesis aims to provide better understanding of the relationship between the acoustic properties and the petrophysical/mineralogical properties in sand-prone rock. It emphasizes the influence of clay minerals. The author develops a method to deposit clay minerals/mineral aggregates in pore space of a rigid rock framework. Kaolinite aggregates were flushed into porous permeable Bentheimer sandstone to evaluate the effect of pore filling minerals on porosity, permeability and acoustic properties. The compressional velocity was hardly affected by the clay content and it was found that the effect of minor quantities of pore filling minerals may be acoustically modelled as an ideal suspension, where the pore fluid bulk modulus is modified by the bulk modulus of the clay minerals. The influence of clays on acoustic velocities in petroleum reservoir rocks was investigated through ultrasonic measurements of compressional- and shear-waves on core material from reservoir and non-reservoir units on the Norwegian Continental Shelf. The measured velocities decrease as the porosity increases, but are not strongly dependent on the clay content. The measured velocities are less dependent on the petrophysical and lithological properties than indicated by previous authors and published mathematical models, and stiffness reduction factors are introduced in two of the models to better match the data. Velocities are estimated along the wellbores based on non-sonic well logs and reflect well the actual sonic log well measurements. In some wells the compressional velocity cannot be modelled correctly by the models suggested. Very high compressional wave anisotropy was measured in the dry samples at atmospheric conditions. As the samples were saturated, the anisotropy was reduced to a maximum of about 30% and decreases further upon pressurization. Reservoir rocks retrieved from 2500 m are more stress dependent than those retrieved from less than 200 m depth. 168 refs., 117 figs., 24

Geological and Petrophysical Characterization of the Ferron Sandstone for 3-D Simulation of a Fluvial-Deltaic Reservoir

Energy Technology Data Exchange (ETDEWEB)

Chidsey, Jr, Thomas C.

2001-10-31

The objective of the Ferron Sandstone project was to develop a comprehensive, interdisciplinary, quantitative characterization f fluvial-deltaic reservoir to allow realistic interwell and reservoir-scale models to be developed for improved oil-field development in similar reservoirs world-wide. Quantitative geological and petrophysical information on the Cretaceous Ferron Sandstone in east-central Utah was collected. Both new and existing data was integrated into a three-dimensional model of spatial variations in porosity, storativity, and tensorial rock permeability at a scale appropriate for inter-well to regional-scale reservoir simulation. Simulation results could improve reservoir management through proper infill and extension drilling strategies, reduction of economic risks, increased recovery from existing oil fields, and more reliable reserve calculations.

Estimation of water-filled and air-filled porosity in the unsaturated zone, Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Nelson, P.H.

1993-01-01

Water content and porosity vary considerably within the unsaturated zone at Yucca Mountain. Measurement of these quantities has been based on core samples. A log-based approach offers the advantage of in-situ measurements, continuous throughout the borehole. This paper describes an algorithm which determines the air-filled and water-filled porosities from density and dielectric logs. The responses of density and dielectric logs are formulated in terms of the matrix properties, air-filled porosity and water-filled porosity. Porosity values obtained from logs from borehole USW G-2 are in reasonable agreement with estimates from core determinations

Heavy mineral sorting in downwards injected Palaeocene sandstone, Siri Canyon, Danish North Sea

DEFF Research Database (Denmark)

Kazerouni, Afsoon Moatari; Friis, Henrik; Svendsen, Johan Byskov

2011-01-01

Post-depositional remobilization and injection of sand are often seen in deep-water clastic systems and has been recently recognised as a significant modifier of deep-water sandstone geometry. Large-scale injectite complexes have been interpreted from borehole data in the Palaeocene Siri Canyon...... of depositional structures in deep-water sandstones, the distinction between "in situ" and injected or remobilised sandstones is often ambiguous. Large scale heavy mineral sorting (in 10 m thick units) is observed in several reservoir units in the Siri Canyon and has been interpreted to represent the depositional...... sorting. In this study we describe an example of effective shear-zone sorting of heavy minerals in a thin downward injected sandstone dyke which was encountered in one of the cores in the Cecilie Field, Siri Canyon. Differences in sorting pattern of heavy minerals are suggested as a tool for petrographic...

Distribution and origin of authigenic smectite clays in Cape Roberts Project Core 3, Victoria Land Basin, Antarctica

Science.gov (United States)

Priestas, A.W.; Wise, S.W.

2007-01-01

Of some 800 m of lower Oligocene marine sediments cored continuously from the seafloor in the Victoria Land Basin of Antarctica at Cape Roberts Site CRP-3, the lower 500 m exhibit authigenic smectite clay coats on shallow-water sandstone grains. A scanning electron microscope/EDS study of 46 fracture sections confirms that the distribution of the clay coats through the unit is not uniform or evenly distributed, but rather varies with depth, original porosity, and the kinds and abundance of source materials. Our results suggest that smectite emplacement resulted from in-situ, low-temperature burial diagenesis rather than hydrothermal or fault-focused thermobaric fluids.

Metaheuristic optimization approaches to predict shear-wave velocity from conventional well logs in sandstone and carbonate case studies

Science.gov (United States)

Emami Niri, Mohammad; Amiri Kolajoobi, Rasool; Khodaiy Arbat, Mohammad; Shahbazi Raz, Mahdi

2018-06-01

Seismic wave velocities, along with petrophysical data, provide valuable information during the exploration and development stages of oil and gas fields. The compressional-wave velocity (VP ) is acquired using conventional acoustic logging tools in many drilled wells. But the shear-wave velocity (VS ) is recorded using advanced logging tools only in a limited number of wells, mainly because of the high operational costs. In addition, laboratory measurements of seismic velocities on core samples are expensive and time consuming. So, alternative methods are often used to estimate VS . Heretofore, several empirical correlations that predict VS by using well logging measurements and petrophysical data such as VP , porosity and density are proposed. However, these empirical relations can only be used in limited cases. The use of intelligent systems and optimization algorithms are inexpensive, fast and efficient approaches for predicting VS. In this study, in addition to the widely used Greenberg–Castagna empirical method, we implement three relatively recently developed metaheuristic algorithms to construct linear and nonlinear models for predicting VS : teaching–learning based optimization, imperialist competitive and artificial bee colony algorithms. We demonstrate the applicability and performance of these algorithms to predict Vs using conventional well logs in two field data examples, a sandstone formation from an offshore oil field and a carbonate formation from an onshore oil field. We compared the estimated VS using each of the employed metaheuristic approaches with observed VS and also with those predicted by Greenberg–Castagna relations. The results indicate that, for both sandstone and carbonate case studies, all three implemented metaheuristic algorithms are more efficient and reliable than the empirical correlation to predict VS . The results also demonstrate that in both sandstone and carbonate case studies, the performance of an artificial bee

Hydrocarbon Potential in Sandstone Reservoir Isolated inside Low Permeability Shale Rock (Case Study: Beruk Field, Central Sumatra Basin)

Science.gov (United States)

Diria, Shidqi A.; Musu, Junita T.; Hasan, Meutia F.; Permono, Widyo; Anwari, Jakson; Purba, Humbang; Rahmi, Shafa; Sadjati, Ory; Sopandi, Iyep; Ruzi, Fadli

2018-03-01

Upper Red Bed, Menggala Formation, Bangko Formation, Bekasap Formation and Duri Formationare considered as the major reservoirs in Central Sumatra Basin (CSB). However, Telisa Formation which is well-known as seal within CSB also has potential as reservoir rock. Field study discovered that lenses and layers which has low to high permeability sandstone enclosed inside low permeability shale of Telisa Formation. This matter is very distinctive and giving a new perspective and information related to the invention of hydrocarbon potential in reservoir sandstone that isolated inside low permeability shale. This study has been conducted by integrating seismic data, well logs, and petrophysical data throughly. Facies and static model are constructed to estimate hydrocarbon potential resource. Facies model shows that Telisa Formation was deposited in deltaic system while the potential reservoir was deposited in distributary mouth bar sandstone but would be discontinued bedding among shale mud-flat. Besides, well log data shows crossover between RHOB and NPHI, indicated that distributary mouth bar sandstone is potentially saturated by hydrocarbon. Target area has permeability ranging from 0.01-1000 mD, whereas porosity varies from 1-30% and water saturation varies from 30-70%. The hydrocarbon resource calculation approximates 36.723 MSTB.

Porosity measurement of amorphous materials by gamma ray transmission; Medida de porosidade de materiais amorfos por transmissao de raios gama

Energy Technology Data Exchange (ETDEWEB)

Poettker, Walmir Eno

2000-07-01

In this work it is presented the measurement of the total porosity of TRe soil, Sandstone Berea rocks and porous ceramics samples. For the determination of the total porosity, the Arquimedes method (conventional) and the gamma ray transmission methodology were employed. The porosity measurement using the gamma methodology has a significant advantage respect to the conventional method due to the fast and non-destructive determination, and also for supplying results with a greater characterization in small scales, in relation to the heterogeneity of the porosity. The conventional methodology presents good results only for homogeneous samples. The experimental set up for the gamma ray transmission technique consisted of a {sup 241} Am source (59,53 keV), a NaI (Tl) scintillation detector, collimators, a XYZ, micrometric table and standard gamma spectrometry electronics connected to a multichannel analyser. (author)

Architecture of an Upper Jurassic barrier island sandstone reservoir, Danish Central Graben:

DEFF Research Database (Denmark)

Johannessen, Peter N.; Nielsen, Lars H.; Nielsen, Lars

2010-01-01

An unusually thick (c. 88 m), transgressive barrier island and shoreface sandstone succession characterizes the Upper Jurassic Heno Formation reservoir of the Freja oil field situated on the boundary of Denmark and Norway. The development and preservation of such thick transgressive barrier island...... sands is puzzling since a barrier island typically migrates landwards during transgression and only a thin succession of back-barrier and shoreface sands is preserved. Investigation of the development and geometry of the Freja reservoir sandstones is problematic since the reservoir is buried c. 5 km...... and seismic resolution is inadequate for architectural analysis. Description of the reservoir sandstone bodies is thus based on sedimentological interpretation and correlation of seven wells, of which five were cored. Palaeotopography played a major role in the position and preservation of the thick reservoir...

Radionuclide transport in sandstones with WIPP brine

International Nuclear Information System (INIS)

Weed, H.C.; Bazan, F.; Fontanilla, J.; Garrison, J.; Rego, J.; Winslow, A.M.

1981-02-01

Retardation factors (R) have been measured for the transport of 3 H, /sup 95m/Tc, and 85 Sr in WIPP brine using St. Peter, Berea, Kayenta, and San Felipe sandstone cores. If tritium is assumed to have R=1, /sup 95m/Tc has R=1.0 to 1.3 and therefore is essentially not retarded. Strontium-85 has R = 1.0 to 1.3 on St. Peter, Berea, and Kayenta, but R=3 on San Felipe. This is attributed to sorption on the matrix material of San Felipe, which has 45 volume % matrix compared with 1 to 10 volume % for the others. Retardation factors (R/sub s/) for 85 Sr calculated from static sorption measurements are unity for all the sandstones. Therefore, the static and transport results for 85 Sr disagree in the case of San Felipe, but agree for St. Peter, Berea, and Kayenta

Computation of porosity and water content from geophysical logs, Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Nelson, P.H.

1996-01-01

Neutron and density logs acquired in boreholes at Yucca Mountain, Nevada are used to determine porosity and water content as a function of depth. Computation of porosity requires an estimate of grain density, which is provided by core data, mineralogical data, or is inferred from rock type where neither core nor mineralogy are available. The porosity estimate is merged with mineralogical data acquired by X-ray diffraction to compute the volumetric fractions of major mineral groups. The resulting depth-based portrayal of bulk rock composition is equivalent to a whole rock analysis of mineralogy and porosity. Water content is computed from epithermal and thermal neutron logs. In the unsaturated zone, the density log is required along with a neutron log. Water content can also be computed from dielectric logs, which were acquired in only a fraction of the boreholes, whereas neutron logs were acquired in all boreholes. Mineralogical data are used to compute a structural (or bound) water estimate, which is subtracted from the total water estimate from the neutron-density combination. Structural water can be subtracted only from intervals where mineralogical analyses are available; otherwise only total water can be reported. The algorithms and procedures are applied to logs acquired during 1979 to 1984 at Yucca Mountain. Examples illustrate the results. Comparison between computed porosity and core measurements shows systematic differences ranging from 0.005 to 0.04. These values are consistent with a sensitivity analysis using uncertainty parameters for good logging conditions. Water content from core measurements is available in only one borehole, yielding a difference between computed and core-based water content of 0.006

Sandstone-type uranium deposits

International Nuclear Information System (INIS)

Finch, W.I.; Davis, J.F.

1985-01-01

World-class sandstone-type uranium deposits are defined as epigenetic concentrations of uranium minerals occurring as uneven impregnations and minor massive replacements primarily in fluvial, lacustrine, and deltaic sandstone formations. The main purpose of this introductory paper is to define, classify, and introduce to the general geologic setting for sandstone-type uranium deposits

Depositional and diagenetic variability within the Cambrian Mount Simon Sandstone: Implications for carbon dioxide sequestration

Science.gov (United States)

Bowen, B.B.; Ochoa, R.I.; Wilkens, N.D.; Brophy, J.; Lovell, T.R.; Fischietto, N.; Medina, C.R.; Rupp, J.A.

2011-01-01

The Cambrian Mount Simon Sandstone is the major target reservoir for ongoing geologic carbon dioxide (CO2) sequestration demonstrations throughout the midwest United States. The potential CO2 reservoir capacity, reactivity, and ultimate fate of injected CO2 depend on textural and compositional properties determined by depositional and diagenetic histories that vary vertically and laterally across the formation. Effective and efficient prediction and use of the available pore space requires detailed knowledge of the depositional and diagenetic textures and mineralogy, how these variables control the petrophysical character of the reservoir, and how they vary spatially. Here, we summarize the reservoir characteristics of the Mount Simon Sandstone based on examination of geophysical logs, cores, cuttings, and analysis of more than 150 thin sections. These samples represent different parts of the formation and depth ranges of more than 9000 ft (>2743 m) across the Illinois Basin and surrounding areas. This work demonstrates that overall reservoir quality and, specifically, porosity do not exhibit a simple relationship with depth, but vary both laterally and with depth because of changes in the primary depositional facies, framework composition (i.e., feldspar concentration), and diverse diagenetic modifications. Diagenetic processes that have been significant in modifying the reservoir include formation of iron oxide grain coatings, chemical compaction, feldspar precipitation and dissolution, multiple generations of quartz overgrowth cementation, clay mineral precipitation, and iron oxide cementation. These variables provide important inputs for calculating CO2 capacity potential, modeling reactivity, and are also an important baseline for comparisons after CO2 injection. Copyright ??2011. The American Association of Petroleum Geologists/Division of Environmental Geosciences. All rights reserved.

The Upper Permian sandstones of Mountains Mecsek: form elements of uranium ore mineralization and facies relations Pt. 2

International Nuclear Information System (INIS)

Vincze, Janos; Somogyi, Janos

1984-01-01

The ore mineralization in the Upper Permian sandstones of Mountais Mecsek, Hungary, was brought about at the oxidation-reduction front between the grey and red sandstones; the predominant rock colour here is green. The sandstones of different colour are oxidation-reduction species. The formation is a megacycle containing in its core grey sandstones of reduced state with coalified plant remains and in its mantle oxidized red sandstones. Uranium accumulates mainly in the transitional green facies. Uranium content gets enriched to a commercial concentration only if the difference in potential of neighbouring beds is in the range of 400-480 mV. The relationship between organic matter and uranium content in the individual facies is shown. The principles of oxidation-reduction processes in the formation of boundary facies are discussed. (V.N.)

The effects of impure CO2 on reservoir sandstones: results from mineralogical and geomechanical experiments

Science.gov (United States)

Marbler, H.; Erickson, K. P.; Schmidt, M.; Lempp, Ch.; Pöllmann, H.

2012-04-01

An experimental study of the behaviour of reservoir sandstones from deep saline aquifers during the injection and geological storage of CO2 with the inherent impurities SOX and NOX is part of the German national project COORAL*. Sample materials were taken from outcrops of possible reservoir formations of Rotliegend and Bunter Sandstones from the North German Basin. A combination of mineralogical alteration experiments and geomechanical tests was carried out on these rocks to study the potential effects of the impurities within the CO2 pore fluid. Altered rock samples after the treatment with CO2 + SOX/NOX in an autoclave system were loaded in a triaxial cell under in-situ pressure and temperature conditions in order to estimate the modifications of the geomechanical rock properties. Mineralogical alterations were observed within the sandstones after the exposure to impure supercritical (sc)CO2 and brine, mainly of the carbonatic, but also of the silicatic cements, as well as of single minerals. Besides the partial solution effects also secondary carbonate and minor silicate mineral precipitates were observed within the pore space of the treated sandstones. These alterations affect the grain structure of the reservoir rock. Results of geomechanical experiments with unaltered sandstones show that the rock strength is influenced by the degree of rock saturation before the experiment and the chemical composition of the pore fluid (scCO2 + SOX + NOX). After long-term autoclave treatment with impure scCO2, the sandstone samples exhibit modified strength parameters and elastic deformation behaviour as well as changes in porosity compared to untreated samples. Furthermore, the injected fluid volume into the pore space of sandstones from the same lithotype varies during triaxial loading depending on the chemistry of the pore fluid. CO2 with NOX and SOX bearing fluid fills a significantly larger proportion of the sandstone pore space than brine with pure scCO2. * The

Rock Physics and Petrographic Parameters Relationship Within Siliciclastic Rocks: Quartz Sandstone Outcrop Study Case

Science.gov (United States)

Syafriyono, S.; Caesario, D.; Swastika, A.; Adlan, Q.; Syafri, I.; Abdurrokhim, A.; Mardiana, U.; Mohamad, F.; Alfadli, M. K.; Sari, V. M.

2018-03-01

Rock physical parameters value (Vp and Vs) is one of fundamental aspects in reservoir characterization as a tool to detect rock heterogenity. Its response is depend on several reservoir conditions such as lithology, pressure and reservoir fluids. The value of Vp and Vs is controlled by grain contact and contact stiffness, a function of clay mineral content and porosity also affected by mineral composition. The study about Vp and Vs response within sandstone and its relationship with petrographic parameters has become important to define anisotrophy of reservoir characteristics distribution and could give a better understanding about local diagenesis that influence clastic reservoir properties. Petrographic analysis and Vp-Vs calculation was carried out to 12 core sample which is obtained by hand-drilling of the outcrop in Sukabumi area, West Java as a part of Bayah Formation. Data processing and interpretation of sedimentary vertical succession showing that this outcrop comprises of 3 major sandstone layers indicating fluvial depositional environment. As stated before, there are 4 petrographic parameters (sorting, roundness, clay mineral content, and grain contact) which are responsible to the differences of shear wave and compressional wave value in this outcrop. Lithology with poor-sorted and well- roundness has Vp value lower than well-sorted and poor-roundness (sub-angular) grain. For the sample with high clay content, Vp value is ranging from 1681 to 2000 m/s and could be getting high until 2190 to 2714 m/s in low clay content sample even though the presence of clay minerals cannot be defined neither as matrix nor cement. The whole sample have suture grain contact indicating telogenesis regime whereas facies has no relationship with Vp and Vs value because of the different type of facies show similar petrographic parameters after diagenesis.

Characterization of the Qishn sandstone reservoir, Masila Basin-Yemen, using an integrated petrophysical and seismic structural approach

Science.gov (United States)

Lashin, Aref; Marta, Ebrahim Bin; Khamis, Mohamed

2016-03-01

This study presents an integrated petrophysical and seismic structural analysis that is carried out to evaluate the reservoir properties of Qishn sandstone as well as the entrapment style of the hydrocarbons at Sharyoof field, Sayun-Masila Basin that is located at the east central of Yemen. The reservoir rocks are dominated by clean porous and permeable sandstones zones usually intercalated with some clay stone interbeds. As identified from well logs, Qishn sandstone is classified into subunits (S1A, S1B, S1C and S2) with different reservoir characteristics and hydrocarbon potentiality. A number of qualitative and quantitative well logging analyses are used to characterize the different subunits of the Qishn reservoir and identify its hydrocarbon potentiality. Dia-porosity, M-N, Pickett, Buckles plots, petrophysical analogs and lateral distribution maps are used in the analysis. Shale volume, lithology, porosity, and fluid saturation are among the most important deduced parameters. The analysis revealed that S1A and S1C are the main hydrocarbon-bearing units. More specifically, S1A unit is the best, as it attains the most prolific hydrocarbon saturations (oil saturation "SH″ up to 65) and reservoir characteristics. An average petrophysical ranges of 4-21%, 16-23%, 11-19%, 0-65%, are detected for S1A unit, regarding shale volume, total and effective porosity, and hydrocarbon saturation, respectively. Meanwhile, S1B unit exhibits less reservoir characteristics (Vsh>30%, ϕEff<15% and SH< 15%). The lateral distribution maps revealed that most of the hydrocarbons (for S1A and S1C units) are indicated at the middle of the study area as NE-SW oriented closures. The analysis and interpretation of seismic data had clarified that the structure of study area is represented by a big middle horst bounded by a group of step-like normal faults at the extreme boundaries (faulted anticlinal-structure). In conclusion, the entrapment of the encountered hydrocarbon at Sharyoof oil

Determination of Porosity in Shale by Double Headspace Extraction GC Analysis.

Science.gov (United States)

Zhang, Chun-Yun; Li, Teng-Fei; Chai, Xin-Sheng; Xiao, Xian-Ming; Barnes, Donald

2015-11-03

This paper reports on a novel method for the rapid determination of the shale porosity by double headspace extraction gas chromatography (DHE-GC). Ground core samples of shale were placed into headspace vials and DHE-GC measurements of released methane gas were performed at a given time interval. A linear correlation between shale porosity and the ratio of consecutive GC signals was established both theoretically and experimentally by comparing with the results from the standard helium pycnometry method. The results showed that (a) the porosity of ground core samples of shale can be measured within 30 min; (b) the new method is not significantly affected by particle size of the sample; (c) the uncertainties of measured porosities of nine shale samples by the present method range from 0.31 to 0.46 p.u.; and (d) the results obtained by the DHE-GC method are in a good agreement with those from the standard helium pycnometry method. In short, the new DHE-GC method is simple, rapid, and accurate, making it a valuable tool for shale gas-related research and applications.

Cyclicity recorded in the provenance sandstones in the sedimentary in fill of the Cameros basin (N. Spain)

Energy Technology Data Exchange (ETDEWEB)

Gonzalez-Acebron, L.; Arribas, J.; Omodeo-Sale, S.; Arribas, E.; Le Pera, E.; Mas, R.; Lopez-Elorza, M.; Fernandez-Diaz, P. R.

2013-06-01

The intra plate Cameros rift basin in the north of Spain was formed came into being between the Tithonian and the Early Albian and contains 9 000 m of mostly continental sediments. This basin is a good example of cyclicity of different depositional sequences (DSs) in sedimentary environments, which show clear repetition in their sandstone composition (petrofacies) and diagenetic patterns. The DSs are arranged in two mega sequences (MSs) separated by a tectonic unconformity. A similar vertical sandstone compositional evolution, subdivided into two stages that repeat cyclically, has been recognised in both MSs: the first comprises quartzo-sedimentolithic petrofacies and the second is made up of several quartzo-feldspathic petrofacies. This was caused by a progression from the recycling of the pre-rift sedimentary cover to the erosion of the mainly plutonic and metamorphic crystalline basement. These changes in the erosion of the different source areas were conditioned by the tectonics of the basin. Furthermore, the original sandstone framework composition conditioned the diagenetic pattern of the two stages: quartzo-sedimentolithic sandstones containing large amounts of very pervasive carbonate cement that reduce their original porosity considerably, and quartzo-feldspathic petrofacies with a rigid framework that maintained the original pores during burial diagenesis. This compositional and diagenetic pattern is probably applicable to other non-volcanic rifted basins, depending upon the original amount of carbonate rock fragments present. (Author)

Porosity measurements of crystalline rocks by laboratory and geophysical methods

International Nuclear Information System (INIS)

Alexander, J.; Hall, D.H.; Storey, B.C.

1981-12-01

Porosity values of igneous and metamorphic crystalline rocks have been determined from core samples taken at specific depths from Altnabreac, by a combination of laboratory and geophysical techniques. Using resaturation and mercury injection methods in three laboratories within I.G.S., porosity values have been derived and the effect of variations in the measuring techniques and results obtained have been compared. Comparison of inter-laboratory porosity values illustrates that systematic errors are present, resulting in higher porosity values for samples subjected to re-testing. This is considered to be caused by the variable nature of the initial samples combined with the inability to completely dry or resaturate samples during a second testing. Geophysical techniques for determining in situ porosity using the neutron log have been carried out in borehole ALA. The neutron log has been calibrated with laboratory derived porosity values and an empirical formula derived enabling porosity values to be ascribed throughout the logged borehole ALA. Comparison of the porosity results from Altnabreac with crystalline samples elsewhere in America, Europe and the U.K. suggest that porosities at Altnabreac are lower than average. However, very few publications concerned with water movement in crystalline areas actually state the method used. (author)

Porosity characterization for heterogeneous shales using integrated multiscale microscopy

Science.gov (United States)

Rassouli, F.; Andrew, M.; Zoback, M. D.

2016-12-01

Pore size distribution analysis plays a critical role in gas storage capacity and fluid transport characterization of shales. Study of the diverse distribution of pore size and structure in such low permeably rocks is withheld by the lack of tools to visualize the microstructural properties of shale rocks. In this paper we try to use multiple techniques to investigate the full pore size range in different sample scales. Modern imaging techniques are combined with routine analytical investigations (x-ray diffraction, thin section analysis and mercury porosimetry) to describe pore size distribution of shale samples from Haynesville formation in East Texas to generate a more holistic understanding of the porosity structure in shales, ranging from standard core plug down to nm scales. Standard 1" diameter core plug samples were first imaged using a Versa 3D x-ray microscope at lower resolutions. Then we pick several regions of interest (ROIs) with various micro-features (such as micro-cracks and high organic matters) in the rock samples to run higher resolution CT scans using a non-destructive interior tomography scans. After this step, we cut the samples and drill 5 mm diameter cores out of the selected ROIs. Then we rescan the samples to measure porosity distribution of the 5 mm cores. We repeat this step for samples with diameter of 1 mm being cut out of the 5 mm cores using a laser cutting machine. After comparing the pore structure and distribution of the samples measured form micro-CT analysis, we move to nano-scale imaging to capture the ultra-fine pores within the shale samples. At this stage, the diameter of the 1 mm samples will be milled down to 70 microns using the laser beam. We scan these samples in a nano-CT Ultra x-ray microscope and calculate the porosity of the samples by image segmentation methods. Finally, we use images collected from focused ion beam scanning electron microscopy (FIB-SEM) to be able to compare the results of porosity measurements

Sandstone-type uranium deposits

International Nuclear Information System (INIS)

Austin, S.R.; D'Andrea, R.F. Jr.

1978-01-01

Three overall factors are necessary for formation of uranium deposits in sandstone: a source of uranium, host rocks capable of transmitting uranium-bearing solutions, and a precipitant. Possible sources of uranium in sandstone-type deposits include groundwaters emanating from granitic highlands, arkosic sediments, tuffaceous material within or overlying the host rocks, connate fluids, and overlying black shales. The first three sources are considered the most likely. Host rocks are generally immature sandstones deposited in alluvial-fan, intermontane-basin or marginal-marine environments, but uranium deposits do occur in well-winnowed barrier-bar or eolian sands. Host rocks for uranium deposits generally show coefficients of permeability on the order of 1 to 100 gal/day/ft 2 . Precipitants are normally agents capable of reducing uranium from the uranyl to the uranous state. The association of uranium with organic matter is unequivocal; H 2 S, a powerful reductant, may have been present at the time of formation of some deposits but may go unnoticed today. Vanadium can serve to preserve the tabular characteristics of some deposits in the near-surface environment, but is considered an unlikely primary precipitant for uranium. Uranium deposits in sandstone are divided into two overall types: peneconcordant deposits, which occur in locally reducing environments in otherwise oxidized sandstones; and roll-type deposits, which occur at the margin of an area where an oxidized groundwater has permeated an otherwise reduced sandstone. Uranium deposits are further broken down into four subclasses; these are described

Hydrogeology of the Potsdam Sandstone in northern New York

Science.gov (United States)

Williams, John H.; Reynolds, Richard J.; Franzi, David A.; Romanowicz, Edwin A.; Paillet, Frederick L.

2010-01-01

The Potsdam Sandstone of Cambrian age forms a transboundary aquifer that extends across northern New York and into southern Quebec. The Potsdam Sandstone is a gently dipping sequence of arkose, subarkose, and orthoquartzite that unconformably overlies Precambrian metamorphic bedrock. The Potsdam irregularly grades upward over a thickness of 450 m from a heterogeneous feldspathic and argillaceous rock to a homogeneous, quartz-rich and matrix-poor rock. The hydrogeological framework of the Potsdam Sandstone was investigated through an analysis of records from 1,500 wells and geophysical logs from 40 wells, and through compilation of GIS coverages of bedrock and surficial geology, examination of bedrock cores, and construction of hydrogeological sections. The upper several metres of the sandstone typically is weathered and fractured and, where saturated, readily transmits groundwater. Bedding-related fractures in the sandstone commonly form sub-horizontal flow zones of relatively high transmissivity. The vertical distribution of sub-horizontal flow zones is variable; spacings of less than 10 m are common. Transmissivity of individual flow zones may be more than 100 m2/d but typically is less than 10 m2/d. High angle fractures, including joints and faults, locally provide vertical hydraulic connection between flow zones. Hydraulic head gradients in the aquifer commonly are downward; a laterally extensive series of sub-horizontal flow zones serve as drains for the groundwater flow system. Vertical hydraulic head differences between shallow and deep flow zones range from 1 m to more than 20 m. The maximum head differences are in recharge areas upgradient from the area where the Chateauguay and Chazy Rivers, and their tributaries, have cut into till and bedrock. Till overlies the sandstone in much of the study area; its thickness is generally greatest in the western part, where it may exceed 50 m. A discontinuous belt of bedrock pavements stripped of glacial drift extends

Application of Advanced Reservoir Characterization, Simulation, and Production Optimization Strategies to Maximize Recovery in Slope and Basin Clastic Reservoirs, West Texas (Delaware Basin)

Energy Technology Data Exchange (ETDEWEB)

Dutton, S.P.; Flanders, W.A.; Guzman, J.I.; Zirczy, H.

1999-06-08

The objective of this Class III project is to demonstrate that detailed reservoir characterization of slope and basin clastic reservoirs in sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost-effective way to recover a higher percentage of the original oil in place through geologically based field development. This year the project focused on reservoir characterization of the East Ford unit, a representative Delaware Mountain Group field that produces from the upper Bell Canyon Formation (Ramsey Sandstone). The field, discovered in 1960, is operated by Orla Petco, Inc., as the East Ford unit; it contained an estimated 19.8 million barrels (MMbbl) of original oil in place. Petrophysical characterization of the East Ford unit was accomplished by integrating core and log data and quantifying petrophysical properties from wireline logs. Most methods of petrophysical analysis that had been developed during an earlier study of the Ford Geraldine unit were successfully transferred to the East Ford unit. The approach that was used to interpret water saturation from resistivity logs, however, had to be modified because in some East Ford wells the log-calculated water saturation was too high and inconsistent with observations made during the actual production. Log-porosity to core-porosity transforms and core-porosity to core-permeability transforms were derived from the East Ford reservoir. The petrophysical data were used to map porosity, permeability, net pay, water saturation, mobil-oil saturation, and other reservoir properties.

Micro-Ct Imaging of Multi-Phase Flow in Carbonates and Sandstones

Science.gov (United States)

Andrew, M. G.; Bijeljic, B.; Blunt, M. J.

2013-12-01

One of the most important mechanisms that limits the escape of CO2 when injected into the subsurface for the purposes of carbon storage is capillary trapping, where CO2 is stranded as pore-scale droplets (ganglia). Prospective storage sites are aquifers or reservoirs that tend to be at conditions where CO2 will reside as a super-critical phase. In order to fully describe physical mechanisms characterising multi-phase flow during and post CO2 injection, experiments need to be conducted at these elevated aquifer/reservoir conditions - this poses a considerable experimental challenge. A novel experimental apparatus has been developed which uses μCT scanning for the non-invasive imaging of the distribution of CO2 in the pore space of rock with resolutions of 7μm at temperatures and pressures representative of the conditions present in prospective saline aquifer CO2 storage sites. The fluids are kept in chemical equilibrium with one-another and with the rock into which they are injected. This is done to prevent the dissolution of the CO2 in the brine to form carbonic acid, which can then react with the rock, particularly carbonates. By eliminating reaction we study the fundamental mechanisms of capillary trapping for an unchanging pore structure. In this study we present a suite of results from three carbonate and two sandstone rock types, showing that, for both cases the CO2 acts as the non-wetting phase and significant quantities of CO2 is trapped. The carbonate examined represent a wide variety of pore topologies with one rock with a very well connected, high porosity pore space (Mt Gambier), one with a lower porosity, poorly connected pore space (Estaillades) and one with a cemented bead pack type pore space (Ketton). Both sandstones (Doddington and Bentheimer) were high permeability granular quartzites. CO2 was injected into each rock, followed by brine injection. After brine injection the entire length of the rock core was scanned, processed and segmented into

Pore Structure and Limit Pressure of Gas Slippage Effect in Tight Sandstone

Science.gov (United States)

You, Lijun; Xue, Kunlin; Kang, Yili; Liao, Yi

2013-01-01

Gas slip effect is an important mechanism that the gas flow is different from liquid flow in porous media. It is generally considered that the lower the permeability in porous media is, the more severe slip effect of gas flow will be. We design and then carry out experiments with the increase of backpressure at the outlet of the core samples based on the definition of gas slip effect and in view of different levels of permeability of tight sandstone reservoir. This study inspects a limit pressure of the gas slip effect in tight sandstones and analyzes the characteristic parameter of capillary pressure curves. The experimental results indicate that gas slip effect can be eliminated when the backpressure reaches a limit pressure. When the backpressure exceeds the limit pressure, the measured gas permeability is a relatively stable value whose range is less than 3% for a given core sample. It is also found that the limit pressure increases with the decreasing in permeability and has close relation with pore structure of the core samples. The results have an important influence on correlation study on gas flow in porous medium, and are beneficial to reduce the workload of laboratory experiment. PMID:24379747

Properties, durability and use of glauconitic Godula sandstones: a relatively less known building stone of the Czech Republic and Poland

Czech Academy of Sciences Publication Activity Database

Vavro, Martin; Vavro, Leona; Martinec, Petr; Souček, Kamil

2016-01-01

Roč. 75, č. 22 (2016), s. 1-17, č. článku 1437. ISSN 1866-6280 R&D Projects: GA MŠk(CZ) LO1406; GA MŠk ED2.1.00/03.0082 Institutional support: RVO:68145535 Keywords : glauconitic sandstones * flysch sediments * properties * porosity * stone durability * Teschen Silesia Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.569, year: 2016 http://link.springer.com/article/10.1007/s12665-016-6248-3

Genesis and distribution pattern of carbonate cements in lacustrine deep-water gravity-flow sandstone reservoirs in the third member of the Shahejie Formation in the Dongying Sag, Jiyang Depression, Eastern China

DEFF Research Database (Denmark)

Yang, Tian; Cao, Yingchang; Friis, Henrik

2018-01-01

The lacustrine deep-water gravity-flow sandstone reservoirs in the third member of the Shahejie Formation are the main exploration target for hydrocarbons in the Dongying Sag, Eastern China. Carbonate cementation is responsible for much of the porosity and permeability reduction in the lacustrine...

Relationship between characteristics of fan-delta sandstone bodies and in-situ leachable sandstone-type uranium mineralization

International Nuclear Information System (INIS)

Nie Fengjun; Zhou Weixun; Guan Taiyang; Li Sitian

2000-01-01

Like normal deltas, fan-deltas are composed of three parts, i.e., fan-delta plain, fan-delta front and pre-fin-delta, In-situ leachable uranium deposits are commonly distributed along the margins of in-land basins. The author analyzes the possible relationship between the basic characteristics of fan-delta sandstone bodies and uranium mineralization. Two examples, e.g., the fan delta depositional systems in the eastern part of Jungger basin and the southern part of Yili basin, are given to illustrate the fan-delta vertical sequence and planar distribution of sedimentary facies. It has been pointed out that the braided channel sandstone bodies on delta plain, sub-aqueous distributional channel sandstone bodies and delta front sandstone bodies may be the favourable host rocks for in-situ leachable sandstone uranium deposits

Measurement of electrical impedance of a Berea sandstone core during the displacement of saturated brine by oil and CO2 injections

Science.gov (United States)

Liu, Yu; Xue, Ziqiu; Park, Hyuck; Kiyama, Tamotsu; Zhang, Yi; Nishizawa, Osamu; Chae, Kwang-seok

2015-12-01

Complex electrical impedance measurements were performed on a brine-saturated Berea sandstone core while oil and CO2 were injected at different pressures and temperatures. The saturations of brine, oil, and CO2 in the core were simultaneously estimated using an X-ray computed tomography scanner. The formation factor of this Berea core and the resistivity indexes versus the brine saturations were calculated using Archie's law. The experimental results found different flow patterns of oil under different pressures and temperatures. Fingers were observed for the first experiment at 10 MPa and 40 °C. The fingers were restrained as the viscosity ratio of oil and water changed in the second (10 MPa and 25 °C) and third (5 MPa and 25 °C) experiments. The resistivity index showed an exponential increase with a decrease in brine saturation. The saturation exponent varied from 1.4 to 4.0 at different pressure and temperature conditions. During the oil injection procedure, the electrical impedance increased with oil saturation and was significantly affected by different oil distributions; therefore, the impedance varied whether the finger was remarkable or not, even if the oil saturation remained constant. During the CO2 injection steps, the impedance showed almost no change with CO2 saturation because the brine in the pores became immobile after the oil injection.

Long-Term CO2 Exposure Experiments - Geochemical Effects on Brine-Saturated Reservoir Sandstone

Science.gov (United States)

Fischer, Sebastian; Zemke, Kornelia; Liebscher, Axel; Wandrey, Maren

2010-05-01

albite during the experiments. Additionally, XRD data suggest anhydrite dissolution in the course of CO2 exposure. The chemical evolution of the brine displays increasing Ca2+ concentrations (Wandrey et al., 2010) in line with the preferred dissolution of the anorthite component of plagioclase. SEM photomicrographs show corrosion textures on mineral surfaces of, e.g., plagioclase. The petrophysical properties of the sandstone samples also suggest slight changes. NMR and MP data indicate a slightly increased porosity and a shifting to larger pore sizes. The physico-chemical measurements imply (i) Ca2+ dissolution from the rock by the fluid, and (ii) slightly increasing porosity, but decreasing permeability. However, additional evaluation is still needed to interconnect the changes suggested to occur during CO2 exposure and to better understand CO2-brine-rock interactions. Supplementary core samples have been removed from the pressure vessels after 21 and 24 months and will soon be analyzed. Further core fragments will remain in storage in the autoclaves for longer-term experiments. References BLASCHKE, A.-W., SCHöNER, R., GAUPP, R. AND FöRSTER, A. (2008): Sandstone petrography and pore system of the Upper Triassic Stuttgart Formation from a CO2 pilot storage site (Ketzin, Germany), Geo 2008 - Resources and Risks in the Earth System, International Conference and 106th Annual Meeting of the Deutsche Gesellschaft für Geowissenschaften e.V. (DGG) and 98th Annual Meeting of the Geologische Vereinigung e.V. (GV) (Aachen 2008), 301. FöRSTER, A, NORDEN, B., ZINCK-JORGENSEN, K., FRYKMAN, P., KUHLENKAMP, J., SPANGENBERG, E., ERZINGER, J., ZIMMER, M., KOPP, J., BORM, G., JUHLIN, C., COSMA, C.-G., HURTER, S. (2006): Baseline Characterization of the CO2SINK Geological Storage Site at Ketzin, Germany, Environmental Geoscience, 13, 3, 145-161. WANDREY, M., FISCHER, S., ZEMKE, K., LIEBSCHER, A., SCHERF, A.-K., VIETH, A., ZETTLITZER, M. and WüRDEMANN, H. (2010), Monitoring

Cathodoluminescence investigations on quartz cement in the sandstones of Khabour Formation from Iraqi Kurdistan Region, Northern Iraq

Science.gov (United States)

Omer, Muhamed F.; Friis, Henrik

2014-03-01

The Ordovician deltaic to shallow marine Khabour Formation in Northern Iraq consists mainly of sandstone with minor siltstone and interbedded shale. The sandstones are pervasively cemented by quartz that resulted in very little preserved primary porosity. Cathodoluminescence and petrographic studies showed that the silica cementation occurred in five successive phases which can be distinguished by their luminescence pattern. The precipitations of two phases have predated the major compaction process while the other phases are younger. The successive phases represent a sequence of changes in silica supply which were classified as very early and early, derived from dissolved biogenic silica that precipitated as opal/microquartz, possibly pre-compactional and of non-luminescent quartz overgrowth type. This was followed by phases whose silica supply derived from pressure solution of quartz, dissolution of feldspar, and hydrothermal fluids related to major thrust fault event. These successive quartz cement phases showed an increase in luminescence and the development of complicated zonation pattern in late-stage quartz cementation.

Outcrop analogue study of Permocarboniferous geothermal sandstone reservoir formations (northern Upper Rhine Graben, Germany): impact of mineral content, depositional environment and diagenesis on petrophysical properties

Science.gov (United States)

Aretz, Achim; Bär, Kristian; Götz, Annette E.; Sass, Ingo

2016-07-01

The Permocarboniferous siliciclastic formations represent the largest hydrothermal reservoir in the northern Upper Rhine Graben in SW Germany and have so far been investigated in large-scale studies only. The Cenozoic Upper Rhine Graben crosses the Permocarboniferous Saar-Nahe Basin, a Variscan intramontane molasse basin. Due to the subsidence in this graben structure, the top of the up to 2-km-thick Permocarboniferous is located at a depth of 600-2900 m and is overlain by Tertiary and Quaternary sediments. At this depth, the reservoir temperatures exceed 150 °C, which are sufficient for geothermal electricity generation with binary power plants. To further assess the potential of this geothermal reservoir, detailed information on thermophysical and hydraulic properties of the different lithostratigraphical units and their depositional environment is essential. Here, we present an integrated study of outcrop analogues and drill core material. In total, 850 outcrop samples were analyzed, measuring porosity, permeability, thermal conductivity and thermal diffusivity. Furthermore, 62 plugs were taken from drillings that encountered or intersected the Permocarboniferous at depths between 1800 and 2900 m. Petrographic analysis of 155 thin sections of outcrop samples and samples taken from reservoir depth was conducted to quantify the mineral composition, sorting and rounding of grains and the kind of cementation. Its influence on porosity, permeability, the degree of compaction and illitization was quantified. Three parameters influencing the reservoir properties of the Permocarboniferous were detected. The strongest and most destructive influence on reservoir quality is related to late diagenetic processes. An illitic and kaolinitic cementation and impregnation of bitumina document CO2- and CH4-rich acidic pore water conditions, which are interpreted as fluids that migrated along a hydraulic contact from an underlying Carboniferous hydrocarbon source rock. Migrating

An Effective Acid Combination for Enhanced Properties and Corrosion Control of Acidizing Sandstone Formation

International Nuclear Information System (INIS)

Shafiq, Mian Umer; Mahmud, Hisham Khaled Ben

2016-01-01

To fulfill the demand of the world energy, more technologies to enhance the recovery of oil production are being developed. Sandstone acidizing has been introduced and it acts as one of the important means to increase oil and gas production. Sandstone acidizing operation generally uses acids, which create or enlarge the flow channels of formation around the wellbore. In sandstone matrix acidizing, acids are injected into the formation at a pressure below the formation fracturing pressure, in which the injected acids react with mineral particles that may restrict the flow of hydrocarbons. Most common combination is Hydrofluoric Acid - Hydrochloric with concentration (3% HF - 12% HCl) known as mud acid. But there are some problems associated with the use of mud acid i.e., corrosion, precipitation. In this paper several new combinations of acids were experimentally screened to identify the most effective combination. The combinations used consist of fluoboric, phosphoric, formic and hydrofluoric acids. Cores were allowed to react with these combinations and results are compared with the mud acid. The parameters, which are analyzed, are Improved Permeability Ratio, strength and mineralogy. The analysis showed that the new acid combination has the potential to be used in sandstone acidizing. (paper)

Core Flooding Experiments and Reactive Transport Modeling of Seasonal Heat Storage in the Hot Deep Gassum Sandstone Formation

DEFF Research Database (Denmark)

Holmslykke, Hanne D.; Kjøller, Claus; Fabricius, Ida Lykke

2017-01-01

Seasonal storage of excess heat in hot deep aquifers is considered to optimize the usage of commonly available energy sources. The chemical effects of heating the Gassum Sandstone Formation to up to 150 degrees C is investigated by combining laboratory core flooding experiments with petrographic ...... minor effects on the properties of the reservoir and that storage of excess heat in the Gassum Formation in the Stenlille area may be possible provided operational precautions are taken....... analysis and geochemical modeling. Synthetic formation water is injected into two sets of Gassum Formation samples at 25, 50 (reservoir temperature), 100, and 150 degrees C with a velocity of 0.05 and 0.1 PV/h, respectively. Results show a significant increase in the aqueous concentration of silicium...... and iron with increasing temperature due to dissolution of silica and siderite. Increasing the reservoir temperature from 50 to 100 degrees C enhanced the naturally occurring weathering of Na-rich feldspar to kaolinite. Dissolution of quartz increased sharply above 100 degrees C and was the dominating...

Athabasca tar sand reservoir properties derived from cores and logs

International Nuclear Information System (INIS)

Woodhouse, R.

1976-01-01

Log interpretation parameters for the Athabasca Tar Sand Lease No. 24 have been determined by careful correlation with Dean and Stark core analysis data. Significant expansion of Athabasca cores occurs as overburden pressure is removed. In the more shaly sands the core analysis procedures remove adsorbed water from the clays leading to further overestimation of porosity and free water volume. Log interpretation parameters (R/sub w/ = 0.5 ohm . m and m = n = 1.5) were defined by correlation with the weight of tar as a fraction of the weight of rock solids (grain or dry weight fraction of tar). This quantity is independent of the water content of the cores, whereas porosity and the weight of tar as a fraction of the bulk weight of fluids plus solids (bulk weight fraction) are both dependent on water content. Charts are provided for the conversion of bulk weight fraction of fluids to porosity; grain weight fraction of fluids to porosity; log derived porosity and core grain weight tar to water saturation. Example results show that the core analysis grain weight fraction of tar is adequately matched by the log analyses. The log results provide a better representation of the reservoir fluid volumes than the core analysis data

Petrophysical study of Szolnok Formation, Endrod gas field,

Directory of Open Access Journals (Sweden)

Abdel Moktader A. El Sayed

2017-03-01

Full Text Available Results of both porosity and permeability can be used by geologists, petrophysicists, and petroleum engineers to evaluate reservoir rock, heterogeneity, and pore space history through the time of deposition and lithifaction. On the other hand, reservoir quality as well as reservoir classification could be performed based on these data correlation. The Szolnok Formation is composed mainly of turbidity elastic deposits while siltstones are intercalated by sandstone beds and streaks of marls. In the present study, 213 core samples are obtained from the Szolnok Formation of the Great Hungarian plain, Hungary. Both horizontal and vertical permeability are measured. The Szolnok Formation has two main lithologic groups: 1. clean sandstone (141 samples and 2. siltstone – marl (72 samples, it can easily differentiate between good, intermediate or even bad reservoirs. Acoustic laboratory measurements have been carried out for only 30 sandstone rock samples parallel to the bedding plane (horizontal. This paper aims to evaluate some petrophysical relationships. On the other hand, both Wyllie and Raymer models were applied for porosity estimation from seismic velocity. It is worthy to mention that reservoir diagnosis of the Szolnok Formation was our target as well. Both the porosity and permeability variation range characterizing the detected lithologic facies of the Szolnok Formation are useful for reservoir zonation. The relationship between helium and mercury porosity for whole studied samples and sandstone samples as well, are supported by a high correlation coefficient and allow its application for prediction of porosity while it reduces costs and time of laboratory measurements. The evaluation of different calculated equations for porosity from compressional wave velocity data of the Szolnok Formation are studied and the relationship between velocity and porosity displays a clear inverse trend. The comparison between laboratory porosity and sonic

Alteration of properties of rock during their selection by shooting core lifter

Energy Technology Data Exchange (ETDEWEB)

Malinin, V F

1969-01-01

During the process of intrusion of the core lifter into rock, splitting and dislocation of the granules and crystals which compose it occur. In the core lifters, single small nondisintegrated fragments are sometimes encountered. Data on comparison of porosity of crushed cores and rock from which they were selected indicate increase in porosity and penetration of the filtrate of the drilling solution during the process of coring. The determined residual oil saturation of the core is different from the residual oil saturation of the rock from which they were selected. The permeability of cores of rock with high porosity is altered.

Cathodoluminescence characteristics of sandstone and the implications for sandstone type No. 512 uranium deposit

International Nuclear Information System (INIS)

Liu Xiaodong; Guan Taiyang

1998-12-01

Cathodoluminescence (CL) technique, as a special petrologic tool, has been applied to the studies of uranium hosted sandstone from No. 512 uranium deposit located in Xinjiang Autonomous Region, Northwest China. The detrital grains including quartz, feldspar, debris and cements display distinguishing CL properties. The quartz grains mainly demonstrate brown and dark blue CL, feldspar grains demonstrate blue and bright blue CL, calcite cement displays bright yellow-orange and orange-red CL with significant CL zoning, while the debris, mud and sand cements have dark red CL, multicolor CL or non-luminescence. The characteristics of overgrowth, fracture healing, and the original contact relations of detrital grains appear much more significant with CL than that with conventional visual methods. Much more information can be contributed by CL technique to decipher the provenance area, to explain the cementation, consolidation and other diagenesis processes of sandstone. The CL technique also provides and efficient tool for identifying detrital grains and cements, and for more precisely estimating the proportions of various detrital grains and cement components in sandstone. The CL emission of uranium hosted sandstone revealed the existence of radiation-damage rims of quartz grains at the places with a little or no uranium minerals nearby, which may imply a uranium-leaching episode during the diagenesis of sandstone

"Sydney sandstone": Heritage Stone from Australia

Science.gov (United States)

Cooper, Barry; Kramar, Sabina

2014-05-01

Sydney is Australia's oldest city being founded in 1788. The city was fortunate to be established on an extensive and a relatively undeformed layer of lithified quartz sandstone of Triassic age that has proved to be an ideal building stone. The stone has been long identified by geologists as the Hawkesbury Sandstone. On the other hand the term "Sydney sandstone" has also been widely used over a long period, even to the extent of being utilised as the title of published books, so its formal designation as a heritage stone will immediately formalise this term. The oldest international usage is believed to be its use in the construction of the Stone Store at Kerikeri, New Zealand (1832-1836). In the late 19th century, public buildings such as hospitals, court houses as well as the prominent Sydney Town Hall, Sydney General Post Office, Art Gallery of New South Wales, State Library of New South Wales as well as numerous schools, churches, office building buildings, University, hotels, houses, retaining walls were all constructed using Sydney sandstone. Innumerable sculptures utilising the gold-coloured stone also embellished the city ranging from decorative friezes and capitals on building to significant monuments. Also in the late 19th and early 20th century, Sydney sandstone was used for major construction in most other major Australian cities especially Melbourne, Adelaide and Brisbane to the extent that complaints were expressed that suitable local stone materials were being neglected. Quarrying of Sydney sandstone continues today. In 2000 it was recorded noted that there were 33 significant operating Sydney sandstone quarries including aggregate and dimension stone operations. In addition sandstone continues to be sourced today from construction sites across the city area. Today major dimension stone producers (eg Gosford Quarries) sell Sydney sandstone not only into the Sydney market but also on national and international markets as cladding and paving products

Computed tomography of drill cores

International Nuclear Information System (INIS)

Taylor, T.

1985-08-01

A preliminary computed tomography evaluation of drill cores of granite and sandstone has generated geologically significant data. Density variations as small as 4 percent and fractures as narrow as 0.1 mm were easily detected

A quantitative comparison of moldic and vuggy porosity structure in karst aquifers using image and geospatial analysis

Science.gov (United States)

Culpepper, A. R.; Manda, A. K.

2011-12-01

Limestone aquifers are vital sources of groundwater for domestic and industrial use throughout the world. To sustain rising population throughout the southeastern United States, aquifers are increasingly exploited to provide the populace clean and reliable water resources. The moldic Castle Hayne and the vuggy Biscayne aquifer systems are two highly productive aquifers that provide critical water resources to millions of citizens in eastern North Carolina and southeastern Florida, respectively. In order to better understand karst aquifers and evaluate the potential for contaminant transport, detailed investigation of 2D porosity and pore geometry using image and geospatial analysis were undertaken. The objective of this study is to compare and contrast the porosity structure of moldic and vuggy karst aquifers by quantifying 2D porosity and pore geometry from images of slabbed core samples and optical televiewer images. Televiewer images and images of painted core samples from the Spring Garden Member of the Castle Hayne aquifer and Miami Limestone Formation of the Biscayne aquifer were acquired for analysis of porosity structure. The procedure for converting images of slabbed core and televiewer images to a GIS useable format consisted of rectification, calibration, image enhancement, classification, recoding and filtering. In GIS, raster or vector formats were used to assess pore attributes (e.g., area and perimeter) and structure. Preliminary results show that both pore area and perimeter for the Spring Garden Member of the Castle Hayne and Miami Limestone Formation of the Biscayne aquifers can be described by exponential distributions. In both sets of slabbed core images the relatively small pores have the highest occurrence, whereas larger pores occur less frequently. However, the moldic Spring Garden Member of the Castle Hayne aquifer has larger pore sizes derived from cores images than the vuggy Miami Limestone Formation of Biscayne aquifer. Total porosity

The sedimentology of uranium-bearing sandstones on the farm Riet Kuil 307, Beaufort West area

International Nuclear Information System (INIS)

Cole, D.I.

1980-10-01

The sedimentology of four sandstones was studied in outcrop and in the subsurface on the farm Riet Kuil 307, near Beaufort West. Only two of these sandstones are mineralised. These are four surface and two subsurface uranium anomalies and one surface uranium anomaly. The sedimentological study was made by means of 47 vertical profiles measured across and adjacent to the surface anomalies as well as 11 core-logs, which intersected the subsurface anomalies. The unmineralised sandstones are included in this study. A total of 19 sedimentary facies was recognised within the fluvial sandstone sequence according to the criteria of grain-size and sedimentary structure. Transitions between the facies were subjected to a Markov chain analysis in order to delineate Markov-dependent transitions. Uranium mineralisation is almost entirely confined to the coarser-grained sedimentary facies, which probably acted as suitable aquifers for the transport of uraniferous solutions prior to the precipitation of the uranium. Horizontally bedded sandstone facies comprises 60 per cent of the total cumulative thickness of mineralisation. The nature of the bedding of this facies may have provided a more effective permeability zone for the transport of uraniferous solutions. This facies contains an abundance of carbonaceous material which acted as an important indirect reductant for the precipitation of uranium from solution. The direct reductant was most probably H 2 S produced by enaerobic bacteria acting on this carbonaceous material shortly after deposition of the sediments. Carbonaceous material also occurs in the other mineralised facies and is considered to be the major control on the mineralisation in the uranium-bearing sandstones

Quality-assured evaluation of effective porosity using fit-for-purpose estimates of clay-mineral volume fraction

Science.gov (United States)

Worthington, Paul F.

2010-05-01

Reservoirs that contain dispersed clay minerals traditionally have been evaluated petrophysically using either the effective or the total porosity system. The major weakness of the former is its reliance on "shale" volume fraction ( Vsh) as a clay-mineral indicator in the determination of effective porosity from well logs. Downhole clay-mineral indicators have usually delivered overestimates of fractional clay-mineral volume ( Vcm) because they use as a reference nearby shale beds that are often assumed to comprise clay minerals exclusively, whereas those beds also include quartzitic silts and other detritus. For this reason, effective porosity is often underestimated significantly, and this shortfall transmits to computed hydrocarbons in place and thence to estimates of ultimate recovery. The problem is overcome here by using, as proxy groundtruths, core porosities that have been upscaled to match the spatial resolutions of porosity logs. Matrix and fluid properties are established over clean intervals in the usual way. Log-derived values of Vsh are tuned so that, on average, the resulting log-derived porosities match the corresponding core porosities over an evaluation interval. In this way, Vsh is rendered fit for purpose as an indicator of clay-mineral content Vcm for purposes of evaluating effective porosity. The method is conditioned to deliver a value of effective porosity that shows overall agreement with core porosity to within the limits of uncertainty of the laboratory measurements. This is achieved through function-, reservoir- and tool-specific Vsh reduction factors that can be applied to downhole estimates of clay-mineral content over uncored intervals of similar reservoir character. As expected, the reduction factors can also vary for different measurement conditions. The reduction factors lie in the range of 0.29-0.80, which means that in its raw form, log-derived Vsh can overestimate the clay-mineral content by more than a factor of three. This

Relationship between soil aggregate strength, shape and porosity for soils under different long-term management

DEFF Research Database (Denmark)

Munkholm, Lars Juhl; Heck, Richard J; Deen, Bill

2016-01-01

were mouldboard ploughing (MP) and no-tillage (NT). The soil coreswere exposed to a drop shatter test and airdried before separation into different size fractions. Ten aggregates fromthe 4–9.2mmsize fraction per core sample (i.e. 320 in all)were X-ray micro-CT scanned. The size, shape and porosity...... porosity and more rounded aggregates than the continuous corn rotation. Surprisingly, therewas no treatment effect on X-ray micro-CT resolvable porosities. Aggregate strength decreased with both total and X-ray micro-CT resolvable porosity even though the correlations were weak. Significant correlation...

Mapping porosity of the deep critical zone in 3D using near-surface geophysics, rock physics modeling, and drilling

Science.gov (United States)

Flinchum, B. A.; Holbrook, W. S.; Grana, D.; Parsekian, A.; Carr, B.; Jiao, J.

2017-12-01

Porosity is generated by chemical, physical and biological processes that work to transform bedrock into soil. The resulting porosity structure can provide specifics about these processes and can improve understanding groundwater storage in the deep critical zone. Near-surface geophysical methods, when combined with rock physics and drilling, can be a tool used to map porosity over large spatial scales. In this study, we estimate porosity in three-dimensions (3D) across a 58 Ha granite catchment. Observations focus on seismic refraction, downhole nuclear magnetic resonance logs, downhole sonic logs, and samples of core acquired by push coring. We use a novel petrophysical approach integrating two rock physics models, a porous medium for the saprolite and a differential effective medium for the fractured rock, that drive a Bayesian inversion to calculate porosity from seismic velocities. The inverted geophysical porosities are within about 0.05 m3/m3 of lab measured values. We extrapolate the porosity estimates below seismic refraction lines to a 3D volume using ordinary kriging to map the distribution of porosity in 3D up to depths of 80 m. This study provides a unique map of porosity on scale never-before-seen in critical zone science. Estimating porosity on these large spatial scales opens the door for improving and understanding the processes that shape the deep critical zone.

Experimental strain analysis of Clarens Sandstone colonised by endolithic lichens

Directory of Open Access Journals (Sweden)

D. Wessels

1995-08-01

Full Text Available Endolithic lichens occur commonly on Clarens Sandstone in South Africa, where they significantly contribute to the weathering of sandstone by means of mechanical and chemical weathering processes. This preliminary investigation reports on the success- ful use of strain gauges in detecting strain differences between sandstone without epilithic lichens and sandstone colonised by the euendolithic lichen Lecidea aff. sarcogynoides Korb. Mechanical weathering, expressed as strain changes, in Clarens Sandstone was studied during the transition from relatively dry winter to wet summer conditions. Daily weathering of sandstone due to thermal expansion and contraction of colonised and uncolonised sandstone could be shown. Our results show that liquid water in sandstone enhances the mechanical weathering of uncolonised Clarens Sandstone while water in the gaseous phase enhances mechanical weathering of sandstone by euendolithic lichens.

Geothermal characteristics of Buntsandstein sandstone reservoir of Alsace

International Nuclear Information System (INIS)

Haffen, Sebastien

2012-01-01

The Buntsandstein, located in the Upper Rhine Graben, appears to be an easy target for geothermal exploitation, linking sandstone and clay with the regional thermal anomaly. This study aims at characterizing petrophysical characteristics of these sandstones as well as the fracturing affecting them, with the intention of providing a conceptual model of the formation which will act as guide for future exploitation. The sedimentary facies are composed by five petrographical facies (clean sandstones, sandstones with clayey coating, clay matrix sandstones, silicified sandstones and carbonated matrix sandstones) which split with variable proportions and control a part of petrophysical properties measured at matrix scale. The comparison between petrophysical data, macroscopic data from temperature gradient analysis, modelling data and fracturing, allows the building of a Buntsandstein Sandstones fluids circulation conceptual model. This analysis points the role of the damage zone of fault zones for fluids transfer at large scale, but also that of two sedimentary facies: marginal erg and Playa Lake. The analysis of different outcrops shows that the fracturing evolves according to the situation in the sedimentary pile and according to the situation in comparison with major tectonic accidents. (author) [fr

Biodegradation of phenols in a sandstone aquifer under aerobic conditions and mixed nitrate and iron reducing conditions

DEFF Research Database (Denmark)

Broholm, Mette; Arvin, Erik

2000-01-01

in the groundwater. The potential for biodegradation of the phenols in the sandstone aquifer at the site has been investigated in laboratory microcosms under aerobic (oxygen amended) and mixed nitrate and iron reducing (nitrate enriched and unamended) anaerobic conditions, at a range of concentrations (low: similar...... to 5 mg 1(-1): high: similar to 60 mg 1(-1), and very high: similar to 600 mg 1(-1)) and in the presence of other organic coal-tar compounds (mono- and polyaromatic hydrocarbons (BTEXs and PAHs) and heterocyclic compounds (NSOs)) and ammonia liquor. Sandstone cores and groundwater for the microcosms...

Mechanical properties of simulated Mars materials: gypsum-rich sandstones and lapilli tuff

Science.gov (United States)

Morrow, Carolyn; Lockner, David; Okubo, Chris

2013-01-01

Observations by the Mars Exploration Rover (MER) Opportunity, and other recent studies on diagenesis in the extensive equatorial layered deposits on Mars, suggest that the likely lithologies of these deposits are gypsum-rich sandstones and tuffaceous sediments (for example, Murchie and others, 2009; Squyres and others, 2012; Zimbelman and Scheidt, 2012). Of particular interest is how the diagenesis history of these sediments (degree of cementation and composition) influences the strength and brittle behavior of the material. For instance, fractures are more common in lower porosity materials under strain, whereas deformation bands, characterized by distributed strain throughout a broader discontinuity in a material, are common in higher porosity sedimentary materials. Such discontinuities can either enhance or restrict fluid flow; hence, failure mode plays an important role in determining the mechanics of fluid migration through sediments (Antonellini and Aydin, 1994; 1995; Taylor and Pollard, 2000; Ogilvie and Glover, 2001). As part of a larger study to characterize processes of fault-controlled fluid flow in volcaniclastic and gypsum-rich sediments on Mars, we have completed a series of laboratory experiments to focus on how gypsum clast content and degree of authigenic cementation affects the strength behavior of simulated Mars rocks. Both axial deformation and hydrostatic pressure tests were done at room temperature under dry conditions.

Electrical Spectroscopy of Permo-Triassic Sandstone From the United Kingdom

Science.gov (United States)

Scott, J.; Barker, R.

2003-12-01

Electrical spectroscopy measurements in the range of mHz to kHz have been made on the dominantly red Permo-Triassic sandstone from the United Kingdom. Samples have been selected from borehole cores from all of the main outcrop areas of sandstone and represent a wide variety of lithologies. This sandstone is an important aquifer for several major cities including Manchester and Birmingham. The samples have been fully saturated with sodium chloride brines and a synthetic groundwater solution that is higher in calcium and magnesium ions than sodium and which closely matches the cation concentrations of the groundwater at Birmingham. Electrical measurements were made using a four-electrode arrangement of silver-silver chloride electrodes. Most of the electrical spectra show a clear, slightly asymmetric, electrical relaxation phenomenon with relaxation peaks in the range of 0.001 Hz to 20 Hz. These relaxation phenomena can be fitted very well by a generalised Cole-Cole model. The relaxation time from this model is found to correlate closely with the dominant pore-throat size from mercury injection. Normalising the chargeability, Cole-Cole m parameter, by the conductivity gives a polarisation magnitude which correlates well with the pore surface to volume ratio (SPOR) for sandstone samples with an even distribution of surface coating clays. The information obtained from the electrical spectra is very useful. The pore-throat size is important in controlling the permeability and in particular the flow of non-aqueous phase fluids. The pore surface area has links to the sorbtion properties of the rock, which are important in estimating contaminant transport. The electrical spectra also provide a useful fingerprint of individual lithologies which could be used for correlation between boreholes or outcrops.

Determination of water-lock critical value of low-permeability sandstones based on digital core

Directory of Open Access Journals (Sweden)

Honglin Zhu

2016-05-01

Full Text Available Research and development of water lock inhibiting measures is very crucial in verifying the link mechanism between the internal factors of water lock and its extent of damage. Based on conventional water-lock physics experiments, however, only the consequence of macro water lock damage can be investigated, while the microscopic mechanism cannot be studied. In this paper, 3D digital cores of low-permeability sandstones were prepared by means of high-resolution micro-CT scan, and their equivalent pore network model was built as well. Virtual “imbibition” experiments controlled by capillary force were carried out by using pore-scale flow simulation. Then the link mechanism between the microscopic internal factors (e.g. wettability, water saturation and pore–throat structure parameters and the water-lock damage degree was discussed. It is shown that the damage degree of water lock reduces gradually as the wettability transits from water wet to gas wet. Therefore, the water lock damage can be reduced effectively and gas-well productivity can be improved so long as the capillary environment is changed from strong water wettability to weak gas wettability. The more different the initial water saturation is from the irreducible water saturation, the more serious the water lock damage is. The damage degree of water lock is in a negative correlation with the coordinate number, but a positive correlation with the pore–throat ratio. Based on the existing research results, water lock tends to form in the formations composed of medium-sized throats. It is concluded that there is a critical throat radius, at which the water lock is the most serious.

PmaCO2 Project: Porosity and CO2 Trapping Mechanisms The Utrillas Formation in SD-1 borehole (Tejada - Burgos): Porosity and Porous Media Modelling

International Nuclear Information System (INIS)

Campos, R.; Barrios, I.; Gonzalez, A. M.

2013-02-01

The aim of PmaCO 2 project, supported by the Secretary of State and Research MINECO (CGL2011-24768) is to increase the knowledge of the microstructure of porous storage formations and thus contribute to the viability of CO 2 sequestration in geological formations. The microporous structure plays an important role not only in the prevalence of a particular trapping mechanism, but also on the amount of CO 2 immobilized. Utrillas facies are investigated in this project as representatives of a deep saline aquifer storage. This publication is a summary of the work done in the first year of the project. We present a study on microstructure of sandstones Utrillas, sampled in borehole, by applying the mercury intrusion porosimetry technique for the experimental determination of porosity and associated parameters. The porous medium was modeled with the PoreCor simulation code based in intrusion-extrusion curves. (Author) 78 refs.

Emplacement processes of tuffaceous sandstones at IODP Site C0011B, Nankai Trough, derived from modal analysis

Science.gov (United States)

Schindlbeck, J. C.; Kutterolf, S.; Freundt, A.

2011-12-01

Tuffaceous sandstones are characterized by their high amount (25 to 75%) of pyroclasts in their modal composition. During IODP Expedition 322 three interbeds of tuffaceous sandstones have been found within a moderately lithified and bioturbated silty claystone sequence in the late Miocene (>7.07 to ~9.0 Ma) upper part of the middle Shikoku Basin facies. Of the three sandstones, units 1 and 2 are single beds whereas unit 3 is composed of three beds. Modal analyses of 29 sandstone thin sections reveal systematic vertical changes within each bed. Generally low-density pyroclasts are enriched at the top (50-60 vol%) of each sandstone bed whereas dense lithic components (25-30 vol%) and minerals (25-30 vol%) are enriched at the bottom. The vertically varying abundance of various types of lithic fragments (sedimentary, volcanoclastic and metamorphic) suggests that these have also been segregated according to their respective densities. The highest amount of fine-grained matrix glass is found in the middle of each bed. Pumice and lithic fragments in the middle and upper parts of the sandstone beds carry ash coatings. For sandstone package 3, in contrast to 1 and 2, core pictures and thin section analyses indicate a subdivision in three units showing the same significant variations in top to bottom enrichment. This suggests three sedimentation events following each other in short time intervals. Glass and mineral chemistry of each sandstone bed show no significant vertical variations. Specifically the matrix glass-shard major element compositions are identical to the pumice clast composition in each tuffaceous sandstone bed. The compositions of amphibole and pyroxene crystals differ only slightly between the sandstone packages. Application of the Ridolfi et al. (2009) thermobarometric calculations to amphiboles of sandstone packages 1 and 2 suggests that each of these was derived from a volcanic system comprising both a deep and a shallow magma reservoir. Thickness and

Sandstone-body and shale-body dimensions in a braided fluvial system: Salt wash sandstone member (Morrison formation), Garfield County, Utah

Science.gov (United States)

Robinson, J.W.; McCabea, P.J.

1997-01-01

Excellent three-dimensional exposures of the Upper Jurassic Salt Wash Sandstone Member of the Morrison Formation in the Henry Mountains area of southern Utah allow measurement of the thickness and width of fluvial sandstone and shale bodies from extensive photomosaics. The Salt Wash Sandstone Member is composed of fluvial channel fill, abandoned channel fill, and overbank/flood-plain strata that were deposited on a broad alluvial plain of low-sinuosity, sandy, braided streams flowing northeast. A hierarchy of sandstone and shale bodies in the Salt Wash Sandstone Member includes, in ascending order, trough cross-bedding, fining-upward units/mudstone intraclast conglomerates, singlestory sandstone bodies/basal conglomerate, abandoned channel fill, multistory sandstone bodies, and overbank/flood-plain heterolithic strata. Trough cross-beds have an average width:thickness ratio (W:T) of 8.5:1 in the lower interval of the Salt Wash Sandstone Member and 10.4:1 in the upper interval. Fining-upward units are 0.5-3.0 m thick and 3-11 m wide. Single-story sandstone bodies in the upper interval are wider and thicker than their counterparts in the lower interval, based on average W:T, linear regression analysis, and cumulative relative frequency graphs. Multistory sandstone bodies are composed of two to eight stories, range up to 30 m thick and over 1500 m wide (W:T > 50:1), and are also larger in the upper interval. Heterolithic units between sandstone bodies include abandoned channel fill (W:T = 33:1) and overbank/flood-plain deposits (W:T = 70:1). Understanding W:T ratios from the component parts of an ancient, sandy, braided stream deposit can be applied in several ways to similar strata in other basins; for example, to (1) determine the width of a unit when only the thickness is known, (2) create correlation guidelines and maximum correlation lengths, (3) aid in interpreting the controls on fluvial architecture, and (4) place additional constraints on input variables to

Visualization and quantification of capillary drainage in the pore space of laminated sandstone by a porous plate method using differential imaging X-ray microtomography

Science.gov (United States)

Lin, Qingyang; Bijeljic, Branko; Rieke, Holger; Blunt, Martin J.

2017-08-01

The experimental determination of capillary pressure drainage curves at the pore scale is of vital importance for the mapping of reservoir fluid distribution. To fully characterize capillary drainage in a complex pore space, we design a differential imaging-based porous plate (DIPP) method using X-ray microtomography. For an exemplar mm-scale laminated sandstone microcore with a porous plate, we quantify the displacement from resolvable macropores and subresolution micropores. Nitrogen (N2) was injected as the nonwetting phase at a constant pressure while the porous plate prevented its escape. The measured porosity and capillary pressure at the imaged saturations agree well with helium measurements and experiments on larger core samples, while providing a pore-scale explanation of the fluid distribution. We observed that the majority of the brine was displaced by N2 in macropores at low capillary pressures, followed by a further brine displacement in micropores when capillary pressure increases. Furthermore, we were able to discern that brine predominantly remained within the subresolution micropores, such as regions of fine lamination. The capillary pressure curve for pressures ranging from 0 to 1151 kPa is provided from the image analysis compares well with the conventional porous plate method for a cm-scale core but was conducted over a period of 10 days rather than up to few months with the conventional porous plate method. Overall, we demonstrate the capability of our method to provide quantitative information on two-phase saturation in heterogeneous core samples for a wide range of capillary pressures even at scales smaller than the micro-CT resolution.

EFFECT OF SANDSTONE ANISOTROPY ON ITS HEAT AND MOISTURE TRANSPORT PROPERTIES

Directory of Open Access Journals (Sweden)

Jan Fořt

2015-09-01

Full Text Available Each type of natural stone has its own geological history, formation conditions, different chemical and mineralogical composition, which influence its possible anisotropy. Knowledge in the natural stones anisotropy represents crucial information for the process of stone quarrying, its correct usage and arrangement in building applications. Because of anisotropy, many natural stones exhibit different heat and moisture transport properties in various directions. The main goal of this study is to analyse several anisotropy indices and their effect on heat transport and capillary absorption. For the experimental determination of the anisotropy effect, five types of sandstone coming from different operating quarries in the Czech Republic are chosen. These materials are often used for restoration of culture heritage monuments as well as for other building applications where they are used as facing slabs, facade panels, decoration stones, paving, etc. For basic characterization of studied materials, determination of their bulk density, matrix density and total open porosity is done. Chemical composition of particular sandstones is analysed by X-Ray Fluorescence. Anisotropy is examined by the non-destructive measurement of velocity of ultrasonic wave propagation. On the basis of ultrasound testing data, the relative anisotropy, total anisotropy and anisotropy coefficient are calculated. Then, the measurement of thermal conductivity and thermal diffusivity in various directions of samples orientation is carried out. The obtained results reveal significant differences between the parameters characterizing the heat transport in various directions, whereas these values are in accordance with the indices of anisotropy. Capillary water transport is described by water absorption coefficient measured using a sorption experiment, which is performed for distilled water and 1M NaCl water solution.  The measured data confirm the effect of anisotropy which is

The Paleozoic-Mesozoic recycling of the Rakaia Terrane, South Island, New Zealand : sandstone clast and sandstone petrology, geochemistry, and geochronology

International Nuclear Information System (INIS)

Wandres, A.M.; Bradshaw, J.D.; Ireland, T.

2005-01-01

The Torlesse terranes - part of the New Zealand Eastern Province - are accretionary complexes that comprise an enormous volume of quartzofeldspathic sandstones and mudstones with subsidiary conglomerates plus minor oceanic assemblages. Two terranes are recognised in the South Island - the Permian to Late Triassic Rakaia Terrane and the Late Jurassic to Early Cretaceous Pahau Terrane. Sandstone clasts from two Rakaia Terrane and two Pahau Terrane conglomerates were collected. We present the first combined detailed information on petrography and geochemistry of Torlesse conglomerate sandstone clasts and use our own and published U-Pb SHRIMP detrital zircon age data to demonstrate the recycling of the Rakaia Terrane into Rakaia strata itself and into Pahau Terrane strata. Sandstone clast major and trace element chemical data largely support petrographic observations derived from thin-section analysis. The similarities of petrographic and geochemical data between sandstone clasts from the Rakaia Terrane and Rakaia sandstones suggest that clasts in the Permian Te Moana and Late Triassic Lake Hill Conglomerates were derived by autocannibalistic reworking of older, consolidated, Rakaia sediments. Data from sandstone clasts from the Pahau Terrane suggest that uplift of the Rakaia Terrane continued into the Cretaceous. These Pahau Terrane clasts indicate that at the time of the Pahau sedimentation Permian to early Late Triassic Rakaia rocks were exposed and recycled into the Pahau Basin. (author). 57 refs., 8 figs., 3 tables

Mechanism for calcite dissolution and its contribution to development of reservoir porosity and permeability in the Kela 2 gas field,Tarim Basin,China

Institute of Scientific and Technical Information of China (English)

2008-01-01

This study is undertaken to understand how calcite precipitation and dissolution contributes to depth-related changes in porosity and permeability of gas-bearing sandstone reservoirs in the Kela 2 gas field of the Tarim Basin, Northwestern China. Sandstone samples and pore water samples are col-lected from well KL201 in the Tarim Basin. Vertical profiles of porosity, permeability, pore water chem-istry, and the relative volume abundance of calcite/dolomite are constructed from 3600 to 4000 m below the ground surface within major oil and gas reservoir rocks. Porosity and permeability values are in-versely correlated with the calcite abundance, indicating that calcite dissolution and precipitation may be controlling porosity and permeability of the reservoir rocks. Pore water chemistry exhibits a sys-tematic variation from the Na2SO4 type at the shallow depth (3600-3630 m), to the NaHCO3 type at the intermediate depth (3630―3695 m),and to the CaCl2 type at the greater depth (3728―3938 m). The geochemical factors that control the calcite solubility include pH, temperature, pressure, Ca2+ concen-tration, the total inorganic carbon concentration (ΣCO2), and the type of pore water. Thermodynamic phase equilibrium and mass conservation laws are applied to calculate the calcite saturation state as a function of a few key parameters. The model calculation illustrates that the calcite solubility is strongly dependent on the chemical composition of pore water, mainly the concentration difference between the total dissolved inorganic carbon and dissolved calcium concentration (i.e., [ΣCO2] -[Ca2+]). In the Na2SO4 water at the shallow depth, this index is close to 0, pore water is near the calcite solubility. Calcite does not dissolve or precipitate in significant quantities. In the NaHCO3 water at the intermedi-ate depth, this index is greater than 0, and pore water is supersaturated with respect to calcite. Massive calcite precipitation was observed at this depth

Cyclicity and reservoir properties of Lower-Middle Miocene sediments of South Kirinsk oil and gas field

Science.gov (United States)

Kurdina, Nadezhda

2017-04-01

Exploration and additional exploration of oil and gas fields, connected with lithological traps, include the spreading forecast of sedimentary bodies with reservoir and seal properties. Genetic identification and forecast of geological bodies are possible in case of large-scale studies, based on the study of cyclicity, structural and textural features of rocks, their composition, lithofacies and depositional environments. Porosity and permeability evaluation of different reservoir groups is also an important part. Such studies have been successfully completed for productive terrigenous Dagi sediments (Lower-Middle Miocene) of the north-eastern shelf of Sakhalin. In order to identify distribution of Dagi reservoirs with different properties in section, core material of the one well of South Kirinsk field has been studied (depth interval from 2902,4 to 2810,5 m). Productive Dagi deposits are represented by gray-colored sandstones with subordinate siltstones and claystones (total thickness 90,5 m). Analysis of cyclicity is based on the concepts of Vassoevich (1977), who considered cycles as geological body, which is the physical result of processes that took place during the sedimentation cycle. Well section was divided into I-X units with different composition and set of genetic features due to layered core description and elementary cyclites identification. According to description of thin sections and results of cylindrical samples porosity and permeability studies five groups of reservoirs were determined. There are coarse-grained and fine-coarse-grained sandstones, fine-grained sandstones, fine-grained silty sandstones, sandy siltstones and siltstones. It was found, in Dagi section there is interval of fine-coarse-grained and coarse-grained sandstones with high petrophysical properties: permeability 3000 mD, porosity more than 25%, but rocks with such properties spread locally and their total thickness is 6 meters only. This interval was described in the IV unit

Sandstone Turning by Abrasive Waterjet

Czech Academy of Sciences Publication Activity Database

Hlaváček, Petr; Cárach, J.; Hloch, Sergej; Vasilko, K.; Klichová, Dagmar; Klich, Jiří; Lehocká, D.

2015-01-01

Roč. 48, č. 6 (2015), s. 2489-2493 ISSN 0723-2632 R&D Projects: GA MŠk ED2.1.00/03.0082; GA MŠk(CZ) LO1406 Institutional support: RVO:68145535 Keywords : turning away from the jet * conventional turning towards the jet * sandstone * abrasive water jet Subject RIV: JQ - Machines ; Tools Impact factor: 2.386, year: 2015 http://www.springerprofessional.de/sandstone-turning-by-abrasive-waterjet/6038028.html

Geologic characterization and carbon storage resource estimates for the knox group, Illinois Basin, Illinois, Indiana and Kentucky

Energy Technology Data Exchange (ETDEWEB)

Harris, David; Ellett, Kevin; Rupp, John; Leetaru, Hannes

2014-09-30

Research documented in this report includes (1) refinement and standardization of regional stratigraphy across the 3-state study area in Illinois, Indiana, and Kentucky, (2) detailed core description and sedimentological interpretion of Knox cores from five wells in western Kentucky, and (3) a detailed calculation of carbon storage volumetrics for the Knox using three different methodologies. Seven regional cross sections document Knox formation distribution and thickness. Uniform stratigraphic nomenclature for all three states helps to resolve state-to-state differences that previously made it difficult to evaluate the Knox on a basin-wide scale. Correlations have also refined the interpretation of an important sandstone reservoir interval in southern Indiana and western Kentucky. This sandstone, a CO2 injection zone in the KGS 1 Blan well, is correlated with the New Richmond Sandstone of Illinois. This sandstone is over 350 ft (107 m) thick in parts of southern Indiana. It has excellent porosity and permeability at sufficient depths, and provides an additional sequestration target in the Knox. The New Richmond sandstone interval has higher predictability than vuggy and fractured carbonates, and will be easier to model and monitor CO2 movement after injection.

Regional distribution regularity of sandstone uranium deposits in Asian continent and prospecting strategy for sandstone uranium deposits in China

International Nuclear Information System (INIS)

Chen Zuyi

2002-01-01

Since the 1980's, after the discovery of numerous sandstone uranium deposits in Middle Asia (Kazakhstan, Uzbekistan) many large sandstone uranium deposits have been found in both Russia and Mongolia. So that Asia has become the most concentrated region of sandstone uranium deposits. The known sandstone uranium deposits occur mostly in a arcual tectonic belt constrained from the north by the Siberian continental block, and the Tarim-North China continental block from the south. This belt is named by Russian geologists as the Central Asian Mobile Belt, and some Chinese geologists call it the 'Mongolian Arc'. A lot of large and super large metallic, non-metallic, gold, polymetallic, porphyry copper and gold, massive sulphide and uranium deposits (of sandstone and volcanic types) with different origin and various types concentrated occur in this belt. The abundant and colourful mineral resources in the region are closely associated with the specific geologic-tectonic evolution of the above belt. It is necessary to strengthen the detailed geologic research and uranium prospecting in the region

Petrographic characterization to build an accurate rock model using micro-CT: Case study on low-permeable to tight turbidite sandstone from Eocene Shahejie Formation.

Science.gov (United States)

Munawar, Muhammad Jawad; Lin, Chengyan; Cnudde, Veerle; Bultreys, Tom; Dong, Chunmei; Zhang, Xianguo; De Boever, Wesley; Zahid, Muhammad Aleem; Wu, Yuqi

2018-03-26

Pore scale flow simulations heavily depend on petrographic characterizing and modeling of reservoir rocks. Mineral phase segmentation and pore network modeling are crucial stages in micro-CT based rock modeling. The success of the pore network model (PNM) to predict petrophysical properties relies on image segmentation, image resolution and most importantly nature of rock (homogenous, complex or microporous). The pore network modeling has experienced extensive research and development during last decade, however the application of these models to a variety of naturally heterogenous reservoir rock is still a challenge. In this paper, four samples from a low permeable to tight sandstone reservoir were used to characterize their petrographic and petrophysical properties using high-resolution micro-CT imaging. The phase segmentation analysis from micro-CT images shows that 5-6% microporous regions are present in kaolinite rich sandstone (E3 and E4), while 1.7-1.8% are present in illite rich sandstone (E1 and E2). The pore system percolates without micropores in E1 and E2 while it does not percolate without micropores in E3 and E4. In E1 and E2, total MICP porosity is equal to the volume percent of macrospores determined from micro-CT images, which indicate that the macropores are well connected and microspores do not play any role in non-wetting fluid (mercury) displacement process. Whereas in E3 and E4 sandstones, the volume percent of micropores is far less (almost 50%) than the total MICP porosity which means that almost half of the pore space was not detected by the micro-CT scan. PNM behaved well in E1 and E2 where better agreement exists in PNM and MICP measurements. While E3 and E4 exhibit multiscale pore space which cannot be addressed with single scale PNM method, a multiscale approach is needed to characterize such complex rocks. This study provides helpful insights towards the application of existing micro-CT based petrographic characterization methodology

Effect of drilling fluids on permeability of uranium sandstone. Report of Investigations/1984

International Nuclear Information System (INIS)

Ahlness, J.K.; Johnson, D.I.; Tweeton, D.R.

1984-01-01

The Bureau of Mines conducted laboratory and field experiments to determine the amount of permeability reduction in uranium sandstone after its exposure to different drilling fluids. Seven polymer and two bentonite fluids were laboratory-tested in their clean condition, and six polymer fluids were tested with simulated drill cuttings added. Sandstone cores cut from samples collected at an open pit uranium mine were the test medium. The clean fluid that resulted in the least permeability reduction was an hydroxyethyl cellulose polymer fluid. The greatest permeability reduction of the clean polymers came from a shale-inhibiting synthetic polymer. Six polymer fluids were tested with simulated drill cuttings added to represent field use. The least permeability reduction was obtained from a multi-polymer blend fluid. A field experiment was performed to compare how two polymer fluids affect formation permeability when used for drilling in situ uranium leaching wells

What classic greywacke (litharenite) can reveal about feldspar diagenesis: An example from Permian Rotliegend sandstone in Hessen, Germany

Science.gov (United States)

Molenaar, Nicolaas; Felder, Marita; Bär, Kristian; Götz, Annette E.

2015-08-01

Rotliegend siliciclastic sediments in southern Hessen (Germany) are a good example of dissolution of detrital feldspars, which is a common feature in many sandstones. Dissolution occurred after mechanical compaction of the lithic-rich sandstone, which experienced framework collapse with pores and pore connections filled and obstructed by deformed ductile lithic grains (pseudomatrix) thereby reducing pore space to microporosity., The advanced degree of compaction and reduced porosity caused low permeability and low hydraulic conductivity of the rock mass. This is further reduced by the presence of wackes and shales that occur intercalated with the sandstones. Feldspar dissolution thus took place in low permeable sediments when large-scale flow of meteoric or acidic fluids is ruled out as a cause of feldspar dissolution. Mineral precipitation (illite, kaolinite, and albite) took place within pseudomatrix and detrital matrix as well as in secondary pores created by feldspar dissolution. Feldspar was the source for the authigenesis. The system was thus closed during burial after framework collapse, and diagenetic reactants in the form of detrital components were already present within the system. The original mass was preserved, but redistributed and diagenetic minerals were the local sinks for the dissolved reactants, precipitating within the system. This also suggests that burial diagenesis in general might be more mass conservative than usually assumed. Rotliegend sandstones thus form a case where, despite of the lack of external exchange of mass by fluid flow, major diagenetic processes did take place and significantly modified the original mineralogy and texture. Feldspar diagenesis can take place from other processes than mere large-scale flushing of open systems as often supposed. It implies that the volumes of rock affected by feldspar diagenesis may be much larger than anticipated based upon the common hold believe that feldspar diagenesis is linked to

Discussion on the origin of bleached sandstone of Qianjiadian uranium deposit

International Nuclear Information System (INIS)

Pang Yaqing; Xiang Weidong; Li Tiangang; Chen Xiaolin; Xia Yuliang

2007-01-01

Qianjiadian uranium deposit is a sandstone-type uranium deposit that has been discovered in Songliao Basin in recent years. Uranium ore bodies are planar or lenticular in shape and under the control of the contact between gray sandstones and bleached sandstones. The bleached sandstone is white in color, cemented loosely, nearly without TOC and pyrite contained and rich in uranium. Geochemical characteristics and types and assemblages of clay minerals of the bleached sandstone reveal that the bleached sandstone is the product of oxidation of the interlayer oxidation zone, and it is a part of the interlayer oxidation zone. The main reasons for white color of the bleached sandstone are transfer of iron ion, oxidation of TOC and kaolinization of sandstone. (authors)

An interlaboratory comparison of methods for measuring rock matrix porosity

International Nuclear Information System (INIS)

Rasilainen, K.; Hellmuth, K.H.; Kivekaes, L.; Ruskeeniemi, T.; Melamed, A.; Siitari-Kauppi, M.

1996-09-01

An interlaboratory comparison study was conducted for the available Finnish methods of rock matrix porosity measurements. The aim was first to compare different experimental methods for future applications, and second to obtain quality assured data for the needs of matrix diffusion modelling. Three different versions of water immersion techniques, a tracer elution method, a helium gas through-diffusion method, and a C-14-PMMA method were tested. All methods selected for this study were established experimental tools in the respective laboratories, and they had already been individually tested. Rock samples for the study were obtained from a homogeneous granitic drill core section from the natural analogue site at Palmottu. The drill core section was cut into slabs that were expected to be practically identical. The subsamples were then circulated between the different laboratories using a round robin approach. The circulation was possible because all methods were non-destructive, except the C-14-PMMA method, which was always the last method to be applied. The possible effect of drying temperature on the measured porosity was also preliminarily tested. These measurements were done in the order of increasing drying temperature. Based on the study, it can be concluded that all methods are comparable in their accuracy. The selection of methods for future applications can therefore be based on practical considerations. Drying temperature seemed to have very little effect on the measured porosity, but a more detailed study is needed for definite conclusions. (author) (4 refs.)

Sedimentary uranium occurrences in Eastern Europe with special reference to sandstone formations

International Nuclear Information System (INIS)

Barthel, F.; Hahn, L.

1985-01-01

Sedimentary uranium deposits, especially in sandstones, play an important role in uranium mining in Eastern Europe. The paper reviews recent publications on uranium occurrences in sandstone formations in the German Democratic Republic, Poland, CSSR, Hungary, Romania, Bulgaria and Albania. The uranium deposits in sandstones in Yugoslavia are described in a separate paper in this volume. Sandstone deposits of the USSR are not reviewed. Uranium mineralizations occur in sandstones from Ordovician to Tertiary age. Major deposits are developed in Upper Carboniferous sandstones in association with coal (GDR, Poland), in Permian strata (CSSR, Hungary, Romania), in Cretaceous sandstones (GDR, CSSR), and in Tertiary sediments (CSSR). The Permian deposits can be compared with deposits of similar age in Northern Italy and Northern Yugoslavia. Roll-type orebodies are developed in some of the Cenomanian sandstones. Tertiary deposits are mainly associated with lignites. Uranium deposits in sandstones of Albania and Bulgaria are not described in the literature. Geologic similarities with sandstone basins in adjacent countries suggest the presence of uranium mineralizations in Permian, Lower Triassic, and Tertiary sandstones. (author)

Quantifying opening-mode fracture spatial organization in horizontal wellbore image logs, core and outcrop: Application to Upper Cretaceous Frontier Formation tight gas sandstones, USA

Science.gov (United States)

Li, J. Z.; Laubach, S. E.; Gale, J. F. W.; Marrett, R. A.

2018-03-01

The Upper Cretaceous Frontier Formation is a naturally fractured gas-producing sandstone in Wyoming. Regionally, random and statistically more clustered than random patterns exist in the same upper to lower shoreface depositional facies. East-west- and north-south-striking regional fractures sampled using image logs and cores from three horizontal wells exhibit clustered patterns, whereas data collected from east-west-striking fractures in outcrop have patterns that are indistinguishable from random. Image log data analyzed with the correlation count method shows clusters ∼35 m wide and spaced ∼50 to 90 m apart as well as clusters up to 12 m wide with periodic inter-cluster spacings. A hierarchy of cluster sizes exists; organization within clusters is likely fractal. These rocks have markedly different structural and burial histories, so regional differences in degree of clustering are unsurprising. Clustered patterns correspond to fractures having core quartz deposition contemporaneous with fracture opening, circumstances that some models suggest might affect spacing patterns by interfering with fracture growth. Our results show that quantifying and identifying patterns as statistically more or less clustered than random delineates differences in fracture patterns that are not otherwise apparent but that may influence gas and water production, and therefore may be economically important.

The neutron porosity tool

International Nuclear Information System (INIS)

Oelgaard, P.L.

1988-01-01

The report contains a review of available information on neutron porosity tools with the emphasis on dual thermal-neutron-detector porosity tools and epithermal-neutron-detector porosity tools. The general principle of such tools is discussed and theoretical models are very briefly reviewed. Available data on tool designs are summarized with special regard to the source-detector distance. Tool operational data, porosity determination and correction of measurements are briefly discussed. (author) 15 refs

Mechanical changes caused by CO2-driven cement dissolution in the Morrow B Sandstone at reservoir conditions: Experimental observations

Science.gov (United States)

Wu, Z.; Luhmann, A. J.; Rinehart, A. J.; Mozley, P.; Dewers, T. A.

2017-12-01

Carbon Capture, Utilization and Storage (CCUS) in transmissive reservoirs is a proposed mechanism in reducing CO2 emissions. Injection of CO2 perturbs reservoir chemistry, and can modify porosity and permeability and alter mineralogy. However, little work has been done on the coupling of rock alteration by CO2 injection and the mechanical integrity of the reservoir. In this study, we perform flow-through experiments on calcite- and dolomite-cemented Pennsylvanian Morrow B Sandstone (West Texas, USA) cores. We hypothesize that poikilotopic calcite cement has a larger impact on chemo-mechanical alteration than disseminated dolomite cement given similar CO2 exposure. With one control brine flow-through experiment and two CO2-plus-brine flow-through experiments for each cement composition, flow rates of 0.1 and 0.01 ml/min were applied under 4200 psi pore fluid pressure and 5000 psi confining pressure at 71 °C. Fluid chemistry and permeability data enable monitoring of mineral dissolution. Ultrasonic velocities were measured pre-test using 1.2 MHz source-receiver pairs at 0.5 MPa axial load and show calcite-cemented samples with higher dynamic elastic moduli than dolomite-cemented samples. Velocities measured post-experiment will identify changes from fluid-rock interaction. We plan to conduct cylinder-splitting destructive mechanical test (Brazil test) to measure the pristine and altered tensile strength of different cemented sandstones. The experiments will identify extents to which cement composition and texture control chemo-mechanical degradation of CCUS reservoirs. Funding for this project is provided by the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL) through the Southwest Regional Partnership on Carbon Sequestration (SWP) under Award No. DE-FC26-05NT42591. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and Engineering Solutions of Sandia LLC, a wholly owned subsidiary of

Effect of temperature on sandstone permeability

DEFF Research Database (Denmark)

Rosenbrand, Esther; Kjøller, Claus

Hot water injection in geothermal sandstone aquifers is considered for seasonal energy storage in Denmark. However, an increase in the aquifer temperature might reduce permeability, and thereby increase production costs. An understanding of the factors that control permeability is required in order...... and the Klinkenberg procedure showed the expected correlation between the two measures, however, differences could be around one order of magnitude. In tight gas sandstones, permeability is often sensitive to net stress, which might change due to the pore pressure change in the Klinkenberg procedure. Besides...... affecting the Klinkenberg procedure, the combined effect of slip and changes in permeability would affect production during pressure depletion in tight gas sandstone reservoirs; therefore effects of gas slip and net stress on permeability were combined in a model based on the Klinkenberg equation. A lower...

Seasonal Deep Aquifer Thermal Energy Storage in the Gassum Sandstone Formation

DEFF Research Database (Denmark)

Holmslykke, H.D.H.; Kjøller, C.; Fabricius, Ida Lykke

Seasonal storage of excess heat in hot deep aquifers is considered to optimise the usage of commonly available energy sources. The potential chemical reactions caused by heating the Gassum Sandstone Formation to up to 150°C is investigated by core flooding experiments combined with petrographic...... analysis and geochemical modelling. Synthetic formation water is injected into two sets of Gassum Formation samples at 25°C, 50°C (reservoir temperature), 100°C and 150°C with a velocity of 0.05 PV/hr and 0.1 PV/hr, respectively. A significant increase in the aqueous concentration of silicium and iron...

Porosity effects during a severe accident

International Nuclear Information System (INIS)

Cazares R, R. I.; Espinosa P, G.; Vazquez R, A.

2015-09-01

The aim of this work is to study the behaviour of porosity effects on the temporal evolution of the distributions of hydrogen concentration and temperature profiles in a fuel assembly where a stream of steam is flowing. The analysis considers the fuel element without mitigation effects. The mass transfer phenomenon considers that the hydrogen generated diffuses in the steam by convection and diffusion. Oxidation of the cladding, rods and other components in the core constructed in zirconium base alloy by steam is a critical issue in LWR accident producing severe core damage. The oxygen consumed by the zirconium is supplied by the up flow of steam from the water pool below the uncovered core, supplemented in the case of PWR by gas recirculation from the cooler outer regions of the core to hotter zones. Fuel rod cladding oxidation is then one of the key phenomena influencing the core behavior under high-temperature accident conditions. The chemical reaction of oxidation is highly exothermic, which determines the hydrogen rate generation and the cladding brittleness and degradation. The heat transfer process in the fuel assembly is considered with a reduced order model. The Boussinesq approximation was applied in the momentum equations for multicomponent flow analysis that considers natural convection due to buoyancy forces, which is related with thermal and hydrogen concentration effects. The numerical simulation was carried out in an averaging channel that represents a core reactor with the fuel rod with its gap and cladding and cooling steam of a BWR. (Author)

Porosity effects during a severe accident

Energy Technology Data Exchange (ETDEWEB)

Cazares R, R. I. [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Posgrado en Energia y Medio Ambiente, San Rafael Atlixco 186, Col. Vicentina, 09340 Ciudad de Mexico (Mexico); Espinosa P, G.; Vazquez R, A., E-mail: ricardo-cazares@hotmail.com [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Area de Ingenieria en Recursos Energeticos, San Rafael Atlixco 186, Col. Vicentina, 09340 Ciudad de Mexico (Mexico)

2015-09-15

The aim of this work is to study the behaviour of porosity effects on the temporal evolution of the distributions of hydrogen concentration and temperature profiles in a fuel assembly where a stream of steam is flowing. The analysis considers the fuel element without mitigation effects. The mass transfer phenomenon considers that the hydrogen generated diffuses in the steam by convection and diffusion. Oxidation of the cladding, rods and other components in the core constructed in zirconium base alloy by steam is a critical issue in LWR accident producing severe core damage. The oxygen consumed by the zirconium is supplied by the up flow of steam from the water pool below the uncovered core, supplemented in the case of PWR by gas recirculation from the cooler outer regions of the core to hotter zones. Fuel rod cladding oxidation is then one of the key phenomena influencing the core behavior under high-temperature accident conditions. The chemical reaction of oxidation is highly exothermic, which determines the hydrogen rate generation and the cladding brittleness and degradation. The heat transfer process in the fuel assembly is considered with a reduced order model. The Boussinesq approximation was applied in the momentum equations for multicomponent flow analysis that considers natural convection due to buoyancy forces, which is related with thermal and hydrogen concentration effects. The numerical simulation was carried out in an averaging channel that represents a core reactor with the fuel rod with its gap and cladding and cooling steam of a BWR. (Author)

Reconstruction of a digital core containing clay minerals based on a clustering algorithm.

Science.gov (United States)

He, Yanlong; Pu, Chunsheng; Jing, Cheng; Gu, Xiaoyu; Chen, Qingdong; Liu, Hongzhi; Khan, Nasir; Dong, Qiaoling

2017-10-01

It is difficult to obtain a core sample and information for digital core reconstruction of mature sandstone reservoirs around the world, especially for an unconsolidated sandstone reservoir. Meanwhile, reconstruction and division of clay minerals play a vital role in the reconstruction of the digital cores, although the two-dimensional data-based reconstruction methods are specifically applicable as the microstructure reservoir simulation methods for the sandstone reservoir. However, reconstruction of clay minerals is still challenging from a research viewpoint for the better reconstruction of various clay minerals in the digital cores. In the present work, the content of clay minerals was considered on the basis of two-dimensional information about the reservoir. After application of the hybrid method, and compared with the model reconstructed by the process-based method, the digital core containing clay clusters without the labels of the clusters' number, size, and texture were the output. The statistics and geometry of the reconstruction model were similar to the reference model. In addition, the Hoshen-Kopelman algorithm was used to label various connected unclassified clay clusters in the initial model and then the number and size of clay clusters were recorded. At the same time, the K-means clustering algorithm was applied to divide the labeled, large connecting clusters into smaller clusters on the basis of difference in the clusters' characteristics. According to the clay minerals' characteristics, such as types, textures, and distributions, the digital core containing clay minerals was reconstructed by means of the clustering algorithm and the clay clusters' structure judgment. The distributions and textures of the clay minerals of the digital core were reasonable. The clustering algorithm improved the digital core reconstruction and provided an alternative method for the simulation of different clay minerals in the digital cores.

Reconstruction of a digital core containing clay minerals based on a clustering algorithm

Science.gov (United States)

He, Yanlong; Pu, Chunsheng; Jing, Cheng; Gu, Xiaoyu; Chen, Qingdong; Liu, Hongzhi; Khan, Nasir; Dong, Qiaoling

2017-10-01

It is difficult to obtain a core sample and information for digital core reconstruction of mature sandstone reservoirs around the world, especially for an unconsolidated sandstone reservoir. Meanwhile, reconstruction and division of clay minerals play a vital role in the reconstruction of the digital cores, although the two-dimensional data-based reconstruction methods are specifically applicable as the microstructure reservoir simulation methods for the sandstone reservoir. However, reconstruction of clay minerals is still challenging from a research viewpoint for the better reconstruction of various clay minerals in the digital cores. In the present work, the content of clay minerals was considered on the basis of two-dimensional information about the reservoir. After application of the hybrid method, and compared with the model reconstructed by the process-based method, the digital core containing clay clusters without the labels of the clusters' number, size, and texture were the output. The statistics and geometry of the reconstruction model were similar to the reference model. In addition, the Hoshen-Kopelman algorithm was used to label various connected unclassified clay clusters in the initial model and then the number and size of clay clusters were recorded. At the same time, the K -means clustering algorithm was applied to divide the labeled, large connecting clusters into smaller clusters on the basis of difference in the clusters' characteristics. According to the clay minerals' characteristics, such as types, textures, and distributions, the digital core containing clay minerals was reconstructed by means of the clustering algorithm and the clay clusters' structure judgment. The distributions and textures of the clay minerals of the digital core were reasonable. The clustering algorithm improved the digital core reconstruction and provided an alternative method for the simulation of different clay minerals in the digital cores.

57Fe Mössbauer and X-ray characterisation of sandstones

International Nuclear Information System (INIS)

Mulaba-Bafubiandi, A. F.; Waanders, F. B.

2013-01-01

Sandstones from the Free State province in South Africa have been mined and processed mainly by small scale and artisanal miners in the rural areas. In the present investigation basic fire proof and water absorption tests, X-ray and γ-ray based characterisation techniques were used to study the sandstones. The collected samples were grouped according to their apparent colour in day light conditions and the elemental analysis showed the presence of a high amount of oxygen (>52%) and silicon (>38%) with Mn, Al, Fe and Ca as major elements in proportions related to the colour distribution of the various sandstones. The uniaxial compressive stress was found to be the highest (56 MPa) for the greyish sandstone and the lowest (8 MPa) for the white sandstone sample, also associated with the lowest (Al+Fe)/Si value of 0.082. The humidity test showed that the 6 % water absorption was lower than the recommended ASTM value of 8 %. The sandstone samples were also subjected to various high temperatures to simulate possible fire conditions and it was found that the non alteration of the mineral species might be one of the reasons why the sandstones are regarded as the most refractory amongst the building materials typically used. Mössbauer spectroscopy revealed that iron is present in all the sandstones, mainly as Fe 3 +  with the black sandstone showing an additional presence of 3 % Fe 2 +  indicating that a higher iron content coupled to higher silicon content, contributes to an increase in the uniaxial compressive strength.

Micro-positron emission tomography for measuring sub-core scale single and multiphase transport parameters in porous media

Science.gov (United States)

Zahasky, Christopher; Benson, Sally M.

2018-05-01

Accurate descriptions of heterogeneity in porous media are important for understanding and modeling single phase (e.g. contaminant transport, saltwater intrusion) and multiphase (e.g. geologic carbon storage, enhanced oil recovery) transport problems. Application of medical imaging to experimentally quantify these processes has led to significant progress in material characterization and understanding fluid transport behavior at laboratory scales. While widely utilized in cancer diagnosis and management, cardiology, and neurology, positron emission tomography (PET) has had relatively limited applications in earth science. This study utilizes a small-bore micro-PET scanner to image and quantify the transport behavior of pulses of a conservative aqueous radiotracer injected during single and multiphase flow experiments in two heterogeneous Berea sandstone cores. The cores are discretized into axial-parallel streamtubes, and using the reconstructed micro-PET data, expressions are derived from spatial moment analysis for calculating sub-core tracer flux and pore water velocity. Using the flux and velocity measurements, it is possible to calculate porosity and saturation from volumetric flux balance, and calculate permeability and water relative permeability from Darcy's law. Second spatial moment analysis enables measurement of sub-core solute dispersion during both single phase and multiphase experiments. A numerical simulation model is developed to verify the assumptions of the streamtube dimension reduction technique. A variation of the reactor ratio is presented as a diagnostic metric to efficiently determine the validity of the streamtube approximation in core and column-scale experiments. This study introduces a new method to quantify sub-core permeability, relative permeability, and dispersion. These experimental and analytical methods provide a foundation for future work on experimental measurements of differences in transport behavior across scales.

Micromechanics of pressure-induced grain crushing in porous rocks

Science.gov (United States)

Zhang, Jiaxiang; Wong, Teng-Fong; Davis, Daniel M.

1990-01-01

The hydrostatic compaction behavior of a suite of porous sandstones was investigated at confining pressures up to 600 MPa and constant pore pressures ranging up to 50 MPa. These five sandstones (Boise, Kayenta, St. Peter, Berea, and Weber) were selected because of their wide range of porosity (5-35%) and grain size (60-460 μm). We tested the law of effective stress for the porosity change as a function of pressure. Except for Weber sandstone (which has the lowest porosity and smallest grain size), the hydrostat of each sandstone shows an inflection point corresponding to a critical effective pressure beyond which an accelerated, irrecoverable compaction occurs. Our microstructural observations show that brittle grain crushing initiates at this critical pressure. We also observed distributed cleavage cracking in calcite and intensive kinking in mica. The critical pressures for grain crushing in our sandstones range from 75 to 380 MPa. In general, a sandstone with higher porosity and larger grain size has a critical pressure which is lower than that of a sandstone with lower porosity and smaller grain size. We formulate a Hertzian fracture model to analyze the micromechanics of grain crushing. Assuming that the solid grains have preexisting microcracks with dimensions which scale with grain size, we derive an expression for the critical pressure which depends on the porosity, grain size, and fracture toughness of the solid matrix. The theoretical prediction is in reasonable agreement with our experimental data as well as other data from soil and rock mechanics studies for which the critical pressures range over 3 orders of magnitude.

Petrography and geochemistry of Jurassic sandstones from the ...

Indian Academy of Sciences (India)

V Periasamy

On the basis of geochemical results, sandstones are classified into arkose, ..... Geochemical classification diagram of sandstone samples from the Jhuran Formation based on log(SiO2/Al2O3)– ..... 1993) showing single trend for the Jhuran.

Sensing, Measuring and Modelling the Mechanical Properties of Sandstone

Science.gov (United States)

Antony, S. J.; Olugbenga, A.; Ozerkan, N. G.

2018-02-01

We present a hybrid framework for simulating the strength and dilation characteristics of sandstone. Where possible, the grain-scale properties of sandstone are evaluated experimentally in detail. Also, using photo-stress analysis, we sense the deviator stress (/strain) distribution at the micro-scale and its components along the orthogonal directions on the surface of a V-notch sandstone sample under mechanical loading. Based on this measurement and applying a grain-scale model, the optical anisotropy index K 0 is inferred at the grain scale. This correlated well with the grain contact stiffness ratio K evaluated using ultrasound sensors independently. Thereafter, in addition to other experimentally characterised structural and grain-scale properties of sandstone, K is fed as an input into the discrete element modelling of fracture strength and dilation of the sandstone samples. Physical bulk-scale experiments are also conducted to evaluate the load-displacement relation, dilation and bulk fracture strength characteristics of sandstone samples under compression and shear. A good level of agreement is obtained between the results of the simulations and experiments. The current generic framework could be applied to understand the internal and bulk mechanical properties of such complex opaque and heterogeneous materials more realistically in future.

Feasibility of a data-constrained prediction of hydrocarbon reservoir sandstone microstructures

International Nuclear Information System (INIS)

Yang, Y S; Gureyev, T E; Tulloh, A; Clennell, M B; Pervukhina, M

2010-01-01

Microstructures are critical for defining material characteristics such as permeability, mechanical, electrical and other physical properties. However, the available techniques for determining compositional microstructures through segmentation of x-ray computed tomography (CT) images are inadequate when there are finer structures than the CT spatial resolution, i.e. when there is more than one material in each voxel. This is the case for CT imaging of geomaterials characterized with submicron porosity and clay coating that control petrophysical properties of rock. This note outlines our data-constrained modelling (DCM) approach for prediction of compositional microstructures, and our investigation of the feasibility of determining sandstone microstructures using multiple CT data sets with different x-ray beam energies. In the DCM approach, each voxel is assumed to contain a mixture of multiple materials, optionally including voids. Our preliminary comparisons using model samples indicate that the DCM-predicted compositional microstructure is consistent with the known original microstructure under low noise conditions. The approach is quite generic and is applicable to predictions of microstructure of various materials. (technical design note)

Micropore Structure Representation of Sandstone in Petroleum Reservoirs Using an Atomic Force Microscope

International Nuclear Information System (INIS)

Bai Yong-Qiang; Zhu Xing; Wu Jun-Zheng; Bai Wen-Guang

2011-01-01

The pore structure of sandstone in an oil reservoir is investigated using atomic force microscopy (AFM). At nanoscale resolution, AFM images of sandstone show us the fine structure. The real height data of images display the three-dimensional space structure of sandstone effectively. The three-dimensional analysis results show that the AFM images of sandstone have unique characteristics that, like fingerprints, can identify different structural properties of sandstones. The results demonstrate that AFM is an effective method used to represent original sandstone in petroleum reservoirs, and may help geologists to appreciate the sandstone in oil reservoirs fully. (general)

Liquid Core Waveguides by UV Modification of Nanoporous Polymer

DEFF Research Database (Denmark)

Christiansen, Mads Brøkner; Gopalakrishnan, Nimi; Sagar, Kaushal Shashikant

2011-01-01

Liquid core waveguides are fabricated from a self-assembled nanoporous polymer, with a porosity of 40%. The high porosity results in an effective refractive index of 1.26 for visible light, i.e. below the refractive index of aqueous solutions. However, since the polymer is hydrophobic, fluids...

Effects of heat-flow and hydrothermal fluids from volcanic intrusions on authigenic mineralization in sandstone formations

Directory of Open Access Journals (Sweden)

Wolela Ahmed

2002-06-01

Full Text Available Volcanic intrusions and hydrothermal activity have modified the diagenetic minerals. In the Ulster Basin, UK, most of the authigenic mineralization in the Permo-Triassic sandstones pre-dated tertiary volcanic intrusions. The hydrothermal fluids and heat-flow from the volcanic intrusions did not affect quartz and feldspar overgrowths. However, clay mineral-transformation, illite-smectite to illite and chlorite was documented near the volcanic intrusions. Abundant actinolite, illite, chlorite, albite and laumontite cementation of the sand grains were also documented near the volcanic intrusions. The abundance of these cementing minerals decreases away from the volcanic intrusions.In the Hartford Basin, USA, the emplacement of the volcanic intrusions took place simultaneous with sedimentation. The heat-flow from the volcanic intrusions and hydrothermal activity related to the volcanics modified the texture of authigenic minerals. Microcrystalline mosaic albite and quartz developed rather than overgrowths and crystals near the intrusions. Chlorite clumps and masses were also documented with microcrystalline mosaic albite and quartz. These features are localized near the basaltic intrusions. Laumontite is also documented near the volcanic intrusions. The reservoir characteristics of the studied sandstone formations are highly affected by the volcanic and hydrothermal fluids in the Hartford and the Ulster Basin. The porosity dropped from 27.4 to zero percent and permeability from 1350 mD to 1 mD.

INAA and petrological study of sandstones from the Angkor monuments

International Nuclear Information System (INIS)

Kucera, J.; Kranda, K.; Soukal, L.; Novak, J.K.; Lang, M.; Poncar, J.; Krausova, I.; Cunin, O.

2008-01-01

We determined 35 major, minor and trace elements in sandstone samples taken from building blocks of 19 Angkor temples and from an old and a new quarry using INAA. We also characterized the sandstone samples with conventional microscopy and electron microprobe analysis. Using cluster analysis, we found no straightforward correlation between the chemical/petrological properties of the sandstones and a presumed period of individual temples construction. The poor correlation may result either from the inherent inhomogeneity of sandstone or just reflect the diversity of quarries that supplied building blocks for the construction of any particular temple. (author)

INTRODUCTION Sandstone beds within Auchi locality are the ...

African Journals Online (AJOL)

The major framework composition is Q F L which classifies the sandstone as Quartz ... The grains are texturally immature as depicted by their subangular edges but mineralogically ..... Fig 6 : Vertical Section of Bioturbated Sandstone Lithofacies Showing Trace Fossils ..... on Water Quality and Planktonic Production in an.

Fuzzy model to predict porosity thought conventional well logs; Modelo Fuzzy para predicao de porosidade via perfis convencionais de poco

Energy Technology Data Exchange (ETDEWEB)

Mimbela, Renzo R.F.; Silva, Jadir C. [Universidade Estadual do Norte Fluminense (UENF), Macae, RJ (Brazil). Lab. de Engenharia e Exploracao do Petroleo (LENEP)

2004-07-01

The well logs have a great applicability in the search and evaluation of hydrocarbon. In this work we calculate porosities of the Namorado field with help of the 'Fuzzy Rule'. This is done segmenting jointly both the neutron ({phi}{sub N}) and density ({phi}{sub d}) porosities logs in groups with better relation of internal linearity. The grouping is processed keeping the best number of groups, which is efficiently chosen by a criterion related to the minimum value of 'Fuzzy Validity' measurement. As a first step, we choose the {phi}{sub N} and {phi}{sub d} values only at that depths where cores exist. To prevent picking measurements errors a previous data filtering is performed by selecting only the and their correspondent values that exhibit a maximum discrepancy with core porosity ({phi}{sub C}) around 5pu (porosity unit). A conventional average porosity {phi}{sub MED}, mixing {phi}{sub N} and {phi}{sub d} is calculated at each point, concerning its own lithological and fluids characteristics. Finally, an inversion algorithm is applied to indicate the best curve curve that fit linearly {phi}{sub C} vs. {phi}{sub MED}, {phi}{sub C} vs. {phi}{sub D} and {phi}{sub C} vs. {phi}{sub N}, and at the same time determines the values of the constants to be extrapolated in order to calculate the porosity of the whole field. (author)

Formation conditions and prospecting criteria for sandstone uranium deposit of interlayer oxidation type

International Nuclear Information System (INIS)

Huang Shijie

1994-01-01

This paper comprehensively analyses the geotectonic setting and favourable conditions, such as structure of the basin, sedimentary facies and paleogeography, geomorphology and climate, hydrodynamics and hydrogeochemistry, the development of interlayered oxidation etc, necessary for the formation of sandstone uranium deposit of interlayered oxidation type. The following prospecting criteria is proposed, namely: abundant uranium source, arid climate, stable big basin, flat-lying sandstone bed, big alluvial fan, little change in sedimentary facies, intercalation of sandstone and mudstone beds, shallow burying of sandstone bed, well-aquiferous sandstone bed, high permeability of sandstone bed, development of interlayered oxidation, and high content of reductant in sandstone. In addition, the 6 in 1 hydrogenic genetic model is proposed

Channel sandstone and bar morphology of the Beaufort group uranium district near Beaufort West

International Nuclear Information System (INIS)

Stear, W.M.

1980-01-01

Sheet-like and lenticular sandstone bodies in the Lower Beaufort Group (Adelaide Subgroup) uranium district occur in megacyclic repetition as superimposed systems of ephemeral fluvial channels that display characteristics of complex lateral and vertical accretion. Channel sandstone bodies are defined on morphological grounds into two types. Sheet sandstone bodies are the commonest type and comprise the bulk of sandstone packages in arenaceous zones of megacycles. Composite sandstone sheets result from multilateral coalescence of individual sandstone bodies. Isolated lenticular sandstone units in argillaceous zones of megacycles comprise sheet and ribbon sandstone types. Multi-storeying is a prominent feature of most channel sandstone bodies and often results in local sandstone thickening. Bedforms relate to the formation of compound bars and record periods of dynamic accretion and erosion. Rarely preserved palaeosurfaces vividly illustrate the fluctuating hydrodynamic conditions that typified ephemeral fluvial sedimentation in a semi-arid environment during Lower Beaufort times

Channel sandstone and bar morphology of the Beaufort group uranium district near Beaufort West

Energy Technology Data Exchange (ETDEWEB)

Stear, W M

1980-01-01

Sheet-like and lenticular sandstone bodies in the Lower Beaufort Group (Adelaide Subgroup) uranium district occur in megacyclic repetition as superimposed systems of ephemeral fluvial channels that display characteristics of complex lateral and vertical accretion. Channel sandstone bodies are defined on morphological grounds into two types. Sheet sandstone bodies are the commonest type and comprise the bulk of sandstone packages in arenaceous zones of megacycles. Composite sandstone sheets result from multilateral coalescence of individual sandstone bodies. Isolated lenticular sandstone units in argillaceous zones of megacycles comprise sheet and ribbon sandstone types. Multi-storeying is a prominent feature of most channel sandstone bodies and often results in local sandstone thickening. Bedforms relate to the formation of compound bars and record periods of dynamic accretion and erosion. Rarely preserved palaeosurfaces vividly illustrate the fluctuating hydrodynamic conditions that typified ephemeral fluvial sedimentation in a semi-arid environment during Lower Beaufort times.

ANALYSIS OF OIL-BEARING CRETACEOUS SANDSTONE HYDROCARBON RESERVOIRS, EXCLUSIVE OF THE DAKOTA SANDSTONE, ON THE JICARILLA APACHE INDIAN RESERVATION, NEW MEXICO

International Nuclear Information System (INIS)

Jennie Ridgley

2000-01-01

A goal of the Mesaverde project was to better define the depositional system of the Mesaverde in hopes that it would provide insight to new or by-passed targets for oil exploration. The new, detailed studies of the Mesaverde give us a better understanding of the lateral variability in depositional environments and facies. Recognition of this lateral variability and establishment of the criteria for separating deltaic, strandplain-barrier, and estuarine deposits from each other permit development of better hydrocarbon exploration models, because the sandstone geometry differs in each depositional system. Although these insights will provide better exploration models for gas exploration, it does not appear that they will be instrumental in finding more oil. Oil in the Mesaverde Group is produced from isolated fields on the Chaco slope; only a few wells define each field. Production is from sandstone beds in the upper part of the Point Lookout Sandstone or from individual fluvial channel sandstones in the Menefee. Stratigraphic traps rather than structural traps are more important. Source of the oil in the Menefee and Point Lookout may be from interbedded organic-rich mudstones or coals rather than from the Lewis Shale. The Lewis Shale appears to contain more type III organic matter and, hence, should produce mainly gas. Outcrop studies have not documented oil staining that might point to past oil migration through the sandstones of the Mesaverde. The lack of oil production may be related to the following: (1) lack of abundant organic matter of the type I or II variety in the Lewis Shale needed to produce oil, (2) ineffective migration pathways due to discontinuities in sandstone reservoir geometries, (3) cementation or early formation of gas prior to oil generation that reduced effective permeabilities and served as barriers to updip migration of oil, or (4) erosion of oilbearing reservoirs from the southern part of the basin. Any new production should mimic that of

ASPEK PROSES DIAGENESIS TERHADAP SIFAT FISIK BATUPASIR FORMASI KEREK, DAERAH KALIPUTIH DAN SEKITARNYA, KECAMATAN SINGOROJO, KABUPATEN KENDAL, JAWA TENGAH

Directory of Open Access Journals (Sweden)

Vanny Hertanto Vahyu

2012-07-01

Full Text Available The sedimentary rock is formed and associated with the diagenesis processes, as all the physical, chemical, andbiological changes in the characteristics of a sediment accumulation from the time the grains are deposited untilthey are metamorphosed. This process is profoundly influence the characteristic of sedimentary rock, including thetexture, internal structure, mineral composition, cementation type, and pore space. Hence, it is important to knowor learn the stage of sandstone diagenesis, especially in the Kerek Formation to mark the correlation betweendiagenesis and physical properties of sandstone.The purpose of this research is to identify the stage of diagenetic processes, diagenetic environment, the type ofcementation, and the relationship between diagenetic stage and physical properties of sandstone. The methods usedin this research are survey method and data analysis method. The survey method includes the making of crosssectionalmeasured stratigraphy and data analysis method includes petrographic and scanning electron microscopy(SEM.The sedimentary structures found in the carbonate sandstones are burrows, convolute ripple lamination, gradedbedding, parallel lamination, cross lamination, current ripple lamination; which are features of turbidity deposition(Bouma sequence. Based on the petrography analysis results for sample P 01 and P 02 showed compaction,cementation, dissolution, and bioturbation, with a porosity value of 1 %. Sample P 03 showed compaction,cementation, dissolution, and bioturbation, with a porosity value of 7 %. Sample P 04 showed compaction,cementation, and dissolution, with a porosity value of 1 %. Sample P 06 showed compaction, cementation,dissolution and replacement, with a porosity value of 5 %. Sample P 07 showed compaction, and cementation, witha porosity value of 30 %. The Lithology type in the research area was Calcarenite with dominant shell fragment,the lithology names are Packed biomicrite (Folks, 1959; in

The influence of substrate transport limitation on porosity and methanogenic activity of anaerobic sludge granules

Energy Technology Data Exchange (ETDEWEB)

Alphenaar, P.A. (Agricultural Univ., Wageningen (Netherlands). Dept. of Environmental Technology); Perez, M.C. (Agricultural Univ., Wageningen (Netherlands). Dept. of Environmental Technology); Lettinga, G. (Agricultural Univ., Wageningen (Netherlands). Dept. of Environmental Technology)

1993-05-01

The relationship between porosity, diameter and methanogenic activity of anaerobic granules has been investigated. Experiments with different granular sludges revealed that substrate transport limitations increase with the diameter of the granules. As a consequence, autolysis can occur in the core of the granule, producing hollow granules. The porosity measurements revealed that the hollow centre is not available for substrate transport. Possibly as an effect of bacterial lysis, the porosity decreases in the more interior layers of the granules. This results in a inactive inner part of the large granules, which is not involved in the treatment process; the specific methanogenic activity decreases with granule size. No marked difference in substrate affinity is observed between granules of different sizes, which probably indicates that for large granules only the exterior is biological active. (orig.)

Use seismic colored inversion and power law committee machine based on imperial competitive algorithm for improving porosity prediction in a heterogeneous reservoir

Science.gov (United States)

Ansari, Hamid Reza

2014-09-01

In this paper we propose a new method for predicting rock porosity based on a combination of several artificial intelligence systems. The method focuses on one of the Iranian carbonate fields in the Persian Gulf. Because there is strong heterogeneity in carbonate formations, estimation of rock properties experiences more challenge than sandstone. For this purpose, seismic colored inversion (SCI) and a new approach of committee machine are used in order to improve porosity estimation. The study comprises three major steps. First, a series of sample-based attributes is calculated from 3D seismic volume. Acoustic impedance is an important attribute that is obtained by the SCI method in this study. Second, porosity log is predicted from seismic attributes using common intelligent computation systems including: probabilistic neural network (PNN), radial basis function network (RBFN), multi-layer feed forward network (MLFN), ε-support vector regression (ε-SVR) and adaptive neuro-fuzzy inference system (ANFIS). Finally, a power law committee machine (PLCM) is constructed based on imperial competitive algorithm (ICA) to combine the results of all previous predictions in a single solution. This technique is called PLCM-ICA in this paper. The results show that PLCM-ICA model improved the results of neural networks, support vector machine and neuro-fuzzy system.

Qualitative and quantitative changes in detrital reservoir rocks caused by CO2-brine-rock interactions during first injection phases (Utrillas sandstones, northern Spain)

Science.gov (United States)

Berrezueta, E.; Ordóñez-Casado, B.; Quintana, L.

2016-01-01

The aim of this article is to describe and interpret qualitative and quantitative changes at rock matrix scale of lower-upper Cretaceous sandstones exposed to supercritical (SC) CO2 and brine. The effects of experimental injection of CO2-rich brine during the first injection phases were studied at rock matrix scale, in a potential deep sedimentary reservoir in northern Spain (Utrillas unit, at the base of the Cenozoic Duero Basin).Experimental CO2-rich brine was exposed to sandstone in a reactor chamber under realistic conditions of deep saline formations (P ≈ 7.8 MPa, T ≈ 38 °C and 24 h exposure time). After the experiment, exposed and non-exposed equivalent sample sets were compared with the aim of assessing possible changes due to the effect of the CO2-rich brine exposure. Optical microscopy (OpM) and scanning electron microscopy (SEM) aided by optical image analysis (OIA) were used to compare the rock samples and get qualitative and quantitative information about mineralogy, texture and pore network distribution. Complementary chemical analyses were performed to refine the mineralogical information and to obtain whole rock geochemical data. Brine composition was also analyzed before and after the experiment.The petrographic study of contiguous sandstone samples (more external area of sample blocks) before and after CO2-rich brine injection indicates an evolution of the pore network (porosity increase ≈ 2 %). It is probable that these measured pore changes could be due to intergranular quartz matrix detachment and partial removal from the rock sample, considering them as the early features produced by the CO2-rich brine. Nevertheless, the whole rock and brine chemical analyses after interaction with CO2-rich brine do not present important changes in the mineralogical and chemical configuration of the rock with respect to initial conditions, ruling out relevant precipitation or dissolution at these early stages to rock-block scale. These results

Applying the universal neutron transport codes to the calculation of well-logging probe response at different rock porosities

International Nuclear Information System (INIS)

Bogacz, J.; Loskiewicz, J.; Zazula, J.M.

1991-01-01

The use of universal neutron transport codes in order to calculate the parameters of well-logging probes presents a new approach first tried in U.S.A. and UK in the eighties. This paper deals with first such an attempt in Poland. The work is based on the use of MORSE code developed in Oak Ridge National Laboratory in U.S.A.. Using CG MORSE code we calculated neutron detector response when surrounded with sandstone of porosities 19% and 38%. During the work it come out that it was necessary to investigate different methods of estimation of the neutron flux. The stochastic estimation method as used currently in the original MORSE code (next collision approximation) can not be used because of slow convergence of its variance. Using the analog type of estimation (calculation of the sum of track lengths inside detector) we obtained results of acceptable variance (∼ 20%) for source-detector spacing smaller than 40 cm. The influence of porosity on detector response is correctly described for detector positioned at 27 cm from the source. At the moment the variances are quite large. (author). 33 refs, 8 figs, 8 tabs

Distinguishing of uranium-bearing sandstone by the geochemical characteristics in northern Sichuan

International Nuclear Information System (INIS)

Wang Wangzhang; Zhang Zhufeng; Wang Yunliang; Sun Shuqin.

1994-01-01

Expounding geochemical characteristics of sandstone-type uranium deposits in northern Sichuan, the authors demonstrate the favourable and unfavourable conditions for enrichment of uranium on the basis of element abundances and ratios of U, Th and K measured by the gamma-ray spectroscopy surveying. The differences between uranium-bearing and non-uranium sandstones and between red sandstone (clay stone) and greenish sandstone can be determined by the gamma-ray spectroscopy (measuring U, Th and K) and XRF analysis (measuring As and Ba). Therefore, the prospecting of the sandstone-type uranium deposits in northern Sichuan can be concentrated in a certain range

Effects of Starch on Properties of Alumina-based Ceramic Cores

Directory of Open Access Journals (Sweden)

LI Fengguang

2016-12-01

Full Text Available In order to improve the poor leachability of alumina-based ceramic cores, different amount of starch was added to the specimens as pore former. Alumina-based ceramic cores were prepared by hot injection technology using corundum powder as base material, paraffin wax and beeswax as plasticizer, silica powder and magnesium oxide powder as mineralizing agent, wherein the parameters of the hot injection process were as follows:temperature of the slurry was 90℃, hot injection pressure was 0.5 MPa and holding time was 25 s. The effects of starch content on the properties of alumina-based ceramic cores were studied and discussed. The results indicate that during sintering period, the loss of starch in the specimens makes porosity of the alumina-based ceramic cores increase. When starch content increases, the room-temperature flexural strength of the ceramic cores reduces and the apparent porosity increases; the volatile solvent increases and the bulk density decreases. After being sintered at 1560℃ for 2.5 h, room-temperature flexural strength of the alumina-based ceramic cores with starch content of 8%(mass fraction is 24.8 MPa, apparent porosity is 47.98% when the volatile solvent is 1.92 g/h and bulk density is 1.88 g/cm3, the complex properties are optimal.

Distribution characteristics of Shihongtan uranium deposits calcareous sandstone and discussion on their genesis

International Nuclear Information System (INIS)

Zhu Huanqiao; Jia Heng; Xu Gaozhong; Li Zhanyou

2007-12-01

It is considered that the calcareous sandstone appear at layer along of a bunch of pear lens on and off, localled near up and down surface of sandbody or washed surface, has sandstone of more macro-grain and more gradation through statistics and analysis of calcareous sandstone in goal layer in Shihongtan uranium deposits. The calcareous sandstone accumulation thickness chorogram demonstrated that the calcareous sandstone centralized distribution in the ore body growth area, thus it can be seen, in the oxidation reduction intermediate belt the calcareous sandstone forms with the uranium mine has the certain origin relation. Choropleth map of summed thickness of calcareous sandstone deserves that it mainly appear in area of uranium body and related cause of formation of ore body of interlayer deacidizing--oxidation belt. (authors)

Deformation bands in porous sandstones their microstructure and petrophysical properties

Energy Technology Data Exchange (ETDEWEB)

Torabi, Anita

2007-12-15

deformation bands are characterized by strain hardening, these new bands feature a central slip surface, which indicates late strain softening. They lack the characteristic compaction envelop, and are typified by higher porosity and lower permeability than previously-described cataclastic deformation bands. Intense background fracturing of the host rock and significant initial porosity are considered to be important in creating these newly-discovered deformation bands. In a related study, we investigate, for millimeter- wide deformation bands, the scale limitation inherent in laboratory measurements of porosity and permeability. The scale limitations imposed by the deformation band relative to the physical sample size motivated us to develop a new method for determining porosity and permeability based on image processing. While plug measurements measure the effective permeability across a 25.4 mm (1 inch) long sample, which includes both host rock and deformation band, the method presented here provides a means to estimate porosity and permeability of deformation band on microscale. This method utilizes low-order (one- and two orders) spatial correlation functions to analyze high-resolution, high-magnification backscatter images, to estimate the porosity and specific surface area of the pore-grain interface in the deformed sandstones. Further, this work demonstrates the use of a modified version of the Kozeny-Carmen relation to calculate permeability by using porosity and specific surface area obtained through the image processing. The result shows that permeability difference between the band and the host rock is up to four orders of magnitude. Moreover, the porosities and permeabilities estimated from image processing are lower than those obtained from their plug measurements; hence the traditional laboratory measurements have been overestimating permeability because of the previously-unrecognized scale problem. In addition, the image processing results clearly show that

Temperature dependent elasticity and damping in dehydrated sandstone

Science.gov (United States)

Darling, T. W.; Struble, W.

2013-12-01

Work reported previously at this conference, outlining our observation of anomalously large elastic softening and damping in dehydrated Berea sandstone at elevated temperatures, has been analysed to study shear and compressional effects separately. Modeling of the sample using COMSOL software was necessary to identify modes, as the vibration spectrum of the sample is poorly approximated by a uniform isotropic solid. The first torsional mode of our evacuated, dry, core softens at nearly twice the rate of Young's modulus modes (bending and compressional) and is also damped nearly twice as strongly as temperature increases. We consider two possible models for explaining this behavior, based on the assumption that the mechanical properties of the sandstone are dominated by the framework of quartz grains and polycrystalline cementation, neglecting initially the effects of clay and feldspar inclusions. The 20cm x 2.54cm diameter core is dry such that the pressure of water vapor in the experiment chamber is below 1e-6 Torr at 70C, suggesting that surface water beyond a small number of monolayers is negligible. Our models consider (1) enhanced sliding of grain boundaries in the cementation at elevated temperature and reduced internal water content, and (2) strain microcracking of the cementatioin at low water content due to anisotropic expansion in the quartz grains. In model (1) interfaces parallel to polyhedral grain surfaces were placed in the cement bonds and assigned frictional properties. Model (2) has not yet been implemented. The overall elasticity of a 3-D several-grain model network was determined by modeling quasistatic loading and measuring displacements. Initial results with a small number of grains/bonds suggests that only the first model provides softening and damping for all the modes, however the details of the effects of defect motioin at individual interfaces as the source for the frictional properties is still being evaluated. Nonlinear effects are

Exploration for sandstone- type uranium mineralisation in the Siwaliks of northwestern Himalaya, India

International Nuclear Information System (INIS)

Swarnkar, B.M.; Kothari, P.K.; Umamaheswar, K.; Srinivasan, S.

2002-01-01

The Siwalik Group with a thickness of about 6000m of fluvial sediments of middle Miocene to Pleistocene age has been explored extensively over two decades for U, using various types of exploration techniques involving air-borne gamma-ray spectrometry, radiation jeep survey, hydrogeochemical survey, ground radiometric survey, radon survey, exploratory drilling and mining, Exploration effort by the Atomic Minerals Directorate for Exploration and Research (AMD) has helped in identifying numerous uranium occurrences spread over the entire Siwalik belt between Poonch (Jammu and Kashmir) in the west and Tanakpur (Uttar Pradesh) in the east, in the northwest Himalaya. Eight significant zones were delineated, mostly confining to distinct stratigraphic horizons of the transition zone between Middle and Upper Siwaliks, and occasionally the transition zone between Lower and Middle Siwaliks. These mineralised zones have a considerable lateral extent of up to 12 km and are associated with sandstones and rarely conglomerates. Uranium mineralisation occurs in the form of peneconcordant lensoidal bodies with individual lenses traceable from a few tens of metres to 700m, sub-parallel to strike or dip, with average grades varying from 0.020 - 0.060% U 3 O 8 and thickness less than a metre to 4m. The host rock of uranium mineralisation is predominantly sandstone containing carbonaceous matter, pyrite and clay pellets. The sandstone is often arkosic and micaceous, and termed as lithic wacke and arkosic wacke. The uranium minerals present are uraninite, pitchblende, coffinite and secondary minerals such as tyuyamunite, metatyuyamunite, uranophane, bayleyite, andersonite, schoepite, liebegite, swartzite, schroekingerite, wulfenite, billictite, betauranophane, autunite and torbernite. Relatively higher concentrations or Se, Mo, Cu, Co, V and Au have been noted in a few uranirerous zones. Concentration or uranium in the Siwalik clastic sediments is controlled by the redox interface

Design and development of controlled porosity osmotic tablet of diltiazem hydrochloride

Directory of Open Access Journals (Sweden)

Sadhana R Shahi

2012-01-01

Full Text Available The present work aims towards the design and development of extended release formulation of freely water-soluble drug diltiazem hydrochloride (DLTZ based on osmotic technology by using controlled porosity approach. DLTZ is an ideal candidate for a zero-order drug delivery system because it is freely water-soluble and has a short half-life (2-3 h. Sodium chloride (Osmogen was added to the core tablet to alter the solubility of DLTZ in an aqueous medium. Cellulose acetate (CA and sorbitol were used as semipermeable membrane and pore former, respectively. The effect of different formulation variables namely concentration of osmogen in the core tablet, % pore former, % weight gain, pH of the dissolution medium and agitation intensity on the in vitro release was studied. DLTZ release was directly proportional to % pore former and inversely proportional to % weight gain. The optimized formulation (F8 delivered DLTZ independent of pH and agitation intensity for 12 h at the upper level concentration of % pore former (25% w/w and middle level concentration of % weight gain (6% w/w. The comparative study of elementary osmotic pump (EOP and controlled porosity osmotic pump revealed that it superior than conventional EOP and also easier and cost effective to formulate.

Formation evaluation in Devonian shale through application of new core and log analysis methods

International Nuclear Information System (INIS)

Luffel, D.L.; Guidry, F.K.

1990-01-01

In the Devonian shale of the Appalachian Basin all porosity in excess of about 2.5 percent is generally occupied by free hydrocarbons, which is mostly gas, based on results of new core and log analysis methods. In this study, sponsored by the Gas Research Institute, reservoir porosities averaged about 5 percent and free gas content averaged about 2 percent by bulk volume, based on analyses on 519 feet of conventional core in four wells. In this source-rich Devonian shale, which also provides the reservoir storage, the rock everywhere appears to be at connate, or irreducible, water saturation corresponding to two or three percent of bulk volume. This became evident when applying the new core and log analysis methods, along with a new plotting method relating bulk volume of pore fluids to porosity. This plotting method has proved to be a valuable tool: it provides useful insight on the fluid distribution present in the reservoir, it provides a clear idea of porosity required to store free hydrocarbons, it leads to a method of linking formation factor to porosity, and it provides a good quality control method to monitor core and log analysis results. In the Devonian shale an important part of the formation evaluation is to determine the amount of kerogen, since this appears as hydrocarbon-filled porosity to conventional logs. In this study Total Organic Carbon and pyrolysis analyses were made on 93 core samples from four wells. Based on these data a new method was used to drive volumetric kerogen and free oil content, and kerogen was found to range up to 26 percent by volume. A good correlation was subsequently developed to derive kerogen from the uranium response of the spectral gamma ray log. Another important result of this study is the measurement of formation water salinity directly on core samples. Results on 50 measurements in the four study wells ranged from 19,000 to 220,000 ppm NaCl

Characterization of application of acu sandstone in ceramic mass

International Nuclear Information System (INIS)

Nobrega, L.F.P.M.; Souza, M.M.; Gomes, Y.S.; Fernandes, D.L.

2016-01-01

The sandstone is a sedimentary rock formed mainly by quartz grains. In Rio Grande do Norte, there is the Potiguar Basin with the Jandaira and Acu Formations. The latter consists of thick layers of whitish-colored sandstones. It stands out as a water storage facility in the state, but it is also used for building aggregates. This article aimed at the use of the sandstone of this formation in the ceramic mass for coating. Initially, the material was sampled. It went through the comminution process to achieve the required granulometry. After this, three formulations were made to incorporate this new material into the traditional ones. The methods were performed according to ISO 13816. After sintering at 1200 °C, the specimens were subjected to the physical tests. A positive result was obtained for the use of the Acu sandstone in low concentrations. It is clear, therefore, its use in ceramics for coating

Examples from the 1.6 Ga Chorhat Sandstone, Vindhyan

Indian Academy of Sciences (India)

This paper addresses macroscopic signatures of microbial mat-related structures within the 1.6 Ga-old Chorhat Sandstone of the Semri Group –the basal stratigraphic unit of the Vindhyan succession in Son valley.The Chorhat Sandstone broadly represents a prograding succession of three depositional facies ranging from ...

Trilobites from the Middle Ordovician Stairway Sandstone, Amadeus Basin, central Australia

DEFF Research Database (Denmark)

Jakobsen, Kristian Grube; Nielsen, Arne Thorshøj; Harper, David Alexander Taylor

2014-01-01

During the Middle Ordovician (Darriwilian) sandstones and siltstones were deposited in the epicontinental Larapintine Sea, which covered large parts of central Australia. The Darriwilian Stairway Sandstone has, for the first time, been sampled stratigraphically for macrofossils to track marine...... benthic biodiversity in this clastic-dominated shallow-water palaeoenvironment situated along the margin of northeastern Gondwana. The faunas from the Stairway Sandstone are generally of low diversity and dominated by bivalves but include several animal groups, with trilobites representing 25......% of the entire shelly fauna. Thirteen trilobite taxa are described from the Stairway Sandstone; the fauna displays a high degree of endemism. One new species, Basilicus (Parabasilicus) brumbyensis sp. nov. is described....

Evaluation of Micro- and Macro-Scale Petrophysical Characteristics of Lower Cretaceous Sandstone with Flow Modeling in µ-CT Imaged Geometry

Science.gov (United States)

Katsman, R.; Haruzi, P.; Waldmann, N.; Halisch, M.

2017-12-01

In this study petrophysical characteristics of rock samples from 3 successive outcrop layers of Hatira Formation Lower Cretaceous Sandstone in northen Israel were evaluated at micro- and macro-scales. The study was carried out by two complementary methods: using conventional experimental measurements of porosity, pore size distribution and permeability; and using a 3D µCT imaging and modeling of signle-phase flow in the real micro-scale sample geometry. The workfow included µ-CT scanning, image processing, image segmentation, and image analyses of pore network, followed by fluid flow simulations at a pore-scale. Upscaling the results of the micro-scale flow simulations yielded a macroscopic permeabilty tensor. Comparison of the upscaled and the experimentally measured rock properties demonstrated a reasonable agreement. In addition, geometrical (pore size distribution, surface area and tortuosity) and topological (Euler characteristic) characteristics of the grains and of the pore network were evaluated at a micro-scale. Statistical analyses of the samples for estimation of anisotropy and inhomogeneity of the porous media were conducted and the results agree with anisotropy and inhomogeneity of the upscaled permeabilty tensor. Isotropic pore orientation of the primary inter-granular porosity was identified in all three samples, whereas the characteristics of the secondary porosity were affected by precipitated cement and clay matrix within the primary pore network. Results of this study provide micro- and macro-scale characteristics of the Lower Cretaceous sandstone that is used in different places over the world as a reservoir for petroleum production and png;base64,R0lGODlhHAARAHcAMSH+GlNvZnR3YXJlOiBNaWNyb3NvZnQgT2ZmaWNlACH5BAEAAAAALAAABAAYAA0AhAAAAAAAAAAAOgAAZgA6kABmtjoAADoAZjo6kDqQ22YAAGa2/5A6AJA6ZpDb/7ZmALb//9uQOtv///+2Zv/bkP//tv//2wECAwECAwECAwECAwECAwECAwECAwECAwECAwVtICBaTGAWIkCaA5S+QKWgZCJSBgo8hASrjJ4osgDqABOB45dcwpopKIznmwpFkxas9uOmqDBZMawYxxS2iakn

Uranium distribution and sandstone depositional environments: oligocene and upper Cretaceous sediments, Cheyenne basin, Colorado

International Nuclear Information System (INIS)

Nibbelink, K.A.; Ethridge, F.G.

1984-01-01

Wyoming-type roll-front uranium deposits occur in the Upper Cretaceous Laramie and Fox Hills sandstones in the Cheyenne basin of northeastern Colorado. The location, geometry, and trend of specific depositional environments of the Oligocene White River and the Upper Cretaceous Laramie and Fox Hills formations are important factors that control the distribution of uranium in these sandstones. The Fox Hills Sandstone consists of up to 450 ft (140 m) of nearshore marine wave-dominated delta and barrier island-tidal channel sandstones which overlie offshore deposits of the Pierre Shale and which are overlain by delta-plain and fluvial deposits of the Laramie Formation. Uranium, which probably originated from volcanic ash in the White River Formation, was transported by groundwater through the fluvial-channel deposits of the White River into the sandstones of the Laramie and Fox Hills formations where it was precipitated. Two favorable depositional settings for uranium mineralization in the Fox Hills Sandstone are: (1) the landward side of barrier-island deposits where barrier sandstones thin and interfinger with back-barrier organic mudstones, and (2) the intersection of barrier-island and tidal channel sandstones. In both settings, sandstones were probably reduced during early burial by diagenesis of contained and adjacent organic matter. The change in permeability trends between the depositional strike-oriented barrier sandstones and the dip-oriented tidal-channel sandstones provided sites for dispersed groundwater flow and, as demonstrated in similar settings in other depositional systems, sites for uranium mineralization

Identification and determination of trapping parameters as key site parameters for CO2 storage for the active CO2 storage site in Ketzin (Germany) - Comparison of different experimental approaches and analysis of field data

Science.gov (United States)

Zemke, Kornelia; Liebscher, Axel

2015-04-01

Petrophysical properties like porosity and permeability are key parameters for a safe long-term storage of CO2 but also for the injection operation itself. The accurate quantification of residual trapping is difficult, but very important for both storage containment security and storage capacity; it is also an important parameter for dynamic simulation. The German CO2 pilot storage in Ketzin is a Triassic saline aquifer with initial conditions of the target sandstone horizon of 33.5 ° C/6.1 MPa at 630 m. One injection and two observation wells were drilled in 2007 and nearly 200 m of core material was recovered for site characterization. From June 2008 to September 2013, slightly more than 67 kt food-grade CO2 has been injected and continuously monitored. A fourth observation well has been drilled after 61 kt injected CO2 in summer 2012 at only 25 m distance to the injection well and new core material was recovered that allow study CO2 induced changes in petrophysical properties. The observed only minor differences between pre-injection and post-injection petrophysical parameters of the heterogeneous formation have no severe consequences on reservoir and cap rock integrity or on the injection behavior. Residual brine saturation for the Ketzin reservoir core material was estimated by different methods. Brine-CO2 flooding experiments for two reservoir samples resulted in 36% and 55% residual brine saturation (Kiessling, 2011). Centrifuge capillary pressure measurements (pc = 0.22 MPa) yielded the smallest residual brine saturation values with ~20% for the lower part of the reservoir sandstone and ~28% for the upper part (Fleury, 2010). The method by Cerepi (2002), which calculates the residual mercury saturation after pressure release on the imbibition path as trapped porosity and the retracted mercury volume as free porosity, yielded unrealistic low free porosity values of only a few percent, because over 80% of the penetrated mercury remained in the samples after

Effects of manual threshold setting on image analysis results of a sandstone sample structural characterization by X-ray microtomography

International Nuclear Information System (INIS)

Moreira, Anderson C.; Fernandes, Celso P.; Fernandes, Jaquiel S.; Marques, Leonardo C.; Appoloni, Carlos R.; Nagata, Rodrigo

2009-01-01

X-ray microtomography is a nondestructive nuclear technique widely applied for samples structural characterization. This methodology permits the investigation of materials porous phase, without special sample preparation, generating bidimensional images of the irradiated sample. The images are generated by the linear attenuation coefficient mapping of the sample. In order to do a quantitative characterization, the images have to be binarized, separating porous phase from the material matrix. The choice of the correct threshold in the grey level histogram is an important and discerning procedure for the binary images creation. Slight variations of the threshold level led to substantial variations in physical parameters determination, like porosity and pore size distribution values. The aim of this work is to evaluate these variations based on some manual threshold setting. Employing Imago image analysis software, four operators determined the porosity and pore size distribution of a sandstone sample by image analysis. The microtomography measurements were accomplished with the following scan conditions: 60 kV, 165 μA, 1 mm Al filter, 0.45 deg step size and 180.0 deg total rotation angle with and 3.8 μm and 11 μm spatial resolution. The global average porosity values, determined by the operators, range from 27.8 to 32.4 % for 3.8 μm spatial resolution and 12.3 to 28.3 % for 11 μm spatial resolution. Percentage differences among the pore size distributions were also found. For the same pore size range, 5.5 % and 17.1 %, for 3.8 μm and 11 μm spatial resolutions respectively, were noted. (author)

Geological characteristic of the main oil and gas producing formations of the upper Austrian molasse basin. Pt. 1. The Eocene sandstones

Energy Technology Data Exchange (ETDEWEB)

Wagner, L [Rohoel-Aufsuchungs-Gesellschaft m.b.H., Vienna (Austria)

1980-09-01

The sandstones of the Upper Eocene are the main oil carriers within RAG's Upper Austrian concession area. The attempt is being made to reconstruct the paleogeography of the Eocene-in which time the sea transgressed the Molasse basin towards N and E - from core and log evidence. From deep Lower Tertiary onwards the mesozoic and older sediments were exposed to intensive erosion, which resulted in a slightly undulating peneplane sloping in a S to SW direction. This erosion plane was - still in Lower Tertiary times - in some areas dissected into horst and graben structures which greatly influenced the deposition of the early Eocene sediments. During the Upper Eocene the Molasse basin began to subside and subsided more strongly in the SW than in the N and NE, so that neritic deposits could form in the first area, whereas lagoonal and brackish sedimentation still prevailed in the latter. The Eocene sandstones are being classified according to their environment of deposition, and their reservoir, characteristics are being studied. Sandstones are absent in the neritic environment of the Discocyclina-marls only. Sand deposits have been encountered as: 1) transgressive horizons directly overlying the pretertiary substrate, 2) infills of channels cut into limnic-brackish sediments, 3) littoral deposits, partly interfingering with Lithothamnium limestone, 4) fine grained sandy marls and nummulitic sandstones within sublittoral to neritic sediments.

Sandstone-filled normal faults: A case study from central California

Science.gov (United States)

Palladino, Giuseppe; Alsop, G. Ian; Grippa, Antonio; Zvirtes, Gustavo; Phillip, Ruy Paulo; Hurst, Andrew

2018-05-01

Despite the potential of sandstone-filled normal faults to significantly influence fluid transmissivity within reservoirs and the shallow crust, they have to date been largely overlooked. Fluidized sand, forcefully intruded along normal fault zones, markedly enhances the transmissivity of faults and, in general, the connectivity between otherwise unconnected reservoirs. Here, we provide a detailed outcrop description and interpretation of sandstone-filled normal faults from different stratigraphic units in central California. Such faults commonly show limited fault throw, cm to dm wide apertures, poorly-developed fault zones and full or partial sand infill. Based on these features and inferences regarding their origin, we propose a general classification that defines two main types of sandstone-filled normal faults. Type 1 form as a consequence of the hydraulic failure of the host strata above a poorly-consolidated sandstone following a significant, rapid increase of pore fluid over-pressure. Type 2 sandstone-filled normal faults form as a result of regional tectonic deformation. These structures may play a significant role in the connectivity of siliciclastic reservoirs, and may therefore be crucial not just for investigation of basin evolution but also in hydrocarbon exploration.

Permeability-Porosity Relationships of Subduction Zone Sediments

Science.gov (United States)

Gamage, K.; Screaton, E.; Bekins, B.; Aiello, I.

2008-12-01

Permeability-porosity relationships for sediments from Northern Barbados, Costa Rica, Nankai, and Peru subduction zones were examined based on their sediment type and grain size distribution. Greater correlation was observed between permeability and porosity for siliciclastic sediments, diatom oozes, and nannofossil chalk than for nannofossil oozes. For siliciclastic sediments, grouping of sediments by clay content yields relationships that are generally consistent with results from other marine settings and suggest decreasing permeability for a given porosity as clay content increases. Correction of measured porosities for smectite content generally improves the quality of permeability-porosity relationships. The relationship between permeability and porosity for diatom oozes may be controlled by the amount of clay present in the ooze, causing diatom oozes to behave similarly to siliciclastic sediments. For a given porosity the nannofossil oozes have higher permeability values by 1.5 orders of magnitude than the siliciclastic sediments. However, the use of a permeability-porosity relation may not be appropriate for unconsolidated carbonates such as nannofossil oozes. This study provided insight to the effects of porosity correction for smectite, variations in lithology and grain size in permeability-porosity relationships. However, further progress in delineating controls on permeability will require more careful and better documented permeability tests on characterized samples.

Brazilian urban porosity : Treat or threat?

NARCIS (Netherlands)

Moreno Pessoa, I.; Tasan-Kok, M.T.; Korthals Altes, W.K.

2016-01-01

Urban areas have spatial discontinuities, such as disconnected neighbourhoods, brownfield areas and leftover places. They can be captured by the metaphor of urban porosity. This paper aims to highlight the potential social consequences of urban porosity by creating a ‘porosity index’. The authors

Three dimensional fracture aperture and porosity distribution using computerized tomography

Science.gov (United States)

Wenning, Q.; Madonna, C.; Joss, L.; Pini, R.

2017-12-01

A wide range of geologic processes and geo-engineered applications are governed by coupled hydromechanical properties in the subsurface. In geothermal energy reservoirs, quantifying the rate of heat transfer is directly linked with the transport properties of fractures, underscoring the importance of fracture aperture characterization for achieving optimal heat production. In this context, coupled core-flooding experiments with non-invasive imaging techniques (e.g., X-Ray Computed Tomography - X-Ray CT) provide a powerful method to make observations of these properties under representative geologic conditions. This study focuses on quantifying fracture aperture distribution in a fractured westerly granite core by using a recently developed calibration-free method [Huo et al., 2016]. Porosity is also estimated with the X-ray saturation technique using helium and krypton gases as saturating fluids, chosen for their high transmissibility and high CT contrast [e.g., Vega et al., 2014]. The westerly granite sample (diameter: 5 cm, length: 10 cm) with a single through-going rough-walled fracture was mounted in a high-pressure aluminum core-holder and placed inside a medical CT scanner for imaging. During scanning the pore fluid pressure was undrained and constant, and the confining pressure was regulated to have the desired effective pressure (0.5, 5, 7 and 10 MPa) under loading and unloading conditions. 3D reconstructions of the sample have been prepared in terms of fracture aperture and porosity at a maximum resolution of (0.24×0.24×1) mm3. Fracture aperture maps obtained independently using helium and krypton for the whole core depict a similar heterogeneous aperture field, which is also dependent on confining pressure. Estimates of the average hydraulic aperture from CT scans are in quantitative agreement with results from fluid flow experiments. However, the latter lack of the level of observational detail achieved through imaging, which further evidence the

Sedimentology, Sequence Stratigraphy and Reservoir Characterization of Samana Suk Formation Exposed in Namal Gorge Section, Salt Range, Mianwali, Punjab, Pakistan

Directory of Open Access Journals (Sweden)

Muhammad Hayat

2016-06-01

Full Text Available Samana Suk Formation of Bathonian-callovain age, exposed in Nammal Gorge Salt Range, has been studied for microfacies and sequence stratigraphic investigation. The formation is mainly composed of limestone, with minor beds of sandstone and marl. The limestone is grey, yellowish and purple in color. Limestone is fine grained, thin to medium bedded and inter-bedded with algal laminations. The sandstone is light yellowish brown, brick red in color, calcareous and quartzose. Within Samana Suk Formation one 2ndorder sequence and two 3rdorder sequences have been identified. Their regional correlation through fine-tuned dating helped to develop basin fill model and to understand facies dynamics. A facie belt comprising a wide belt of carbonate facies characterized by Peloidal Packstone microfacies represents inner ramp setting and Pelletal/ Peloidal Wackstone, Mud-Wackstone and Mudstone microfacies represent the low energy lagoonal environment. The sandstone lithofacies represents high energy beach environment which indicates aggrading to pro-grading pattern. The porosity analysis has been done on different samples of limestone and sandstone. For the porosity analysis the Image J software is used. In limestone the porosity ranges up to 6% while in sandstone the porosity ranging up to 18%. From the field and porosity analysis it is concluded that Samana Suk Formation in study area is good reservoir.

The mineralogical composition of sandstone and its effect on sulphur dioxide deposition

Directory of Open Access Journals (Sweden)

Müller, Urs

2008-06-01

Full Text Available Air pollutants often accelerate stone deterioration in historical buildings and monuments in urban areas. The pollutants are themselves the products of fossil fuel combustion and intensive farming. While this trend seems to have been curbed by strict emission laws in the European Union, in most developing and emerging countries air pollution is an ongoing process due to increasing energy needs and vehicle traffic. Many factors condition natural stone behaviour with respect to gaseous pollutants. Two of the more prominent of such factors are the composition of the atmosphere and the type of stone. Due to their porosity, sandstones are particularly vulnerable to air pollutant attack. Many of the reactions between non-carbonaceous sandstones and these gases are not well understood, however. The present study aimed to acquire an understanding of the processes and factors governing sandstone behaviour when exposed to sulphur dioxide. Seven different sandstones from southern and eastern Germany were analyzed for the study. The binder composition of the stones varied significantly. They also exhibited completely different behaviour in connection with SO2 sorption. Interestingly, while the amount of SO2 deposited was unrelated to the specific surface area of the sandstones, this parameter was closely correlated to the iron oxide content. Iron oxide phases are believed to act as a catalyst in the oxidation of SO2 to SO3. The type and amount of clay mineral, in turn, was found to have no significant impact on initial SO2 deposition in sandstones.Los contaminantes atmosféricos son con frecuencia responsables de la aceleración de la degradación de la piedra en los edificios y monumentos históricos de las zonas urbanas. Los contaminantes en sí son productos de reacción procedentes de la combustión de los hidrocarburos y de la agricultura intensiva. Dentro de la Comunidad Europea, el avance parece haberse ralentizado mediante restrictivas leyes sobre

Sandstone-type uranium deposits. Summary and conclusions

International Nuclear Information System (INIS)

Finch, W.I.

1985-01-01

The similarity of most of the deposits described in this report is striking even though they occur in sandstone host rocks ranging in age from Carboniferous to Tertiary and on every continent outside the polar regions. Geologic environments of the uranium deposits consist of distinctive sets of tectonic and sedimentary-depositional systems, all of which have some common threads of favorable geologic processes. In this summary paper it is hoped that this report has sharpened an understanding of the deposit's ''home environment'' that will aid future exploration for these resource-important sandstone-type uranium ores

Aquifer prospect and vulnerability of Upper Maastrichtian sandstones: Case of Ajali and Nsukka formations in the Northern Enugu Province, southeastern Nigeria

Science.gov (United States)

Ukpai, Stephen N.; Ezeh, Hilary N.; Igwe, James O.

2017-11-01

Two typical aquifer systems, namely, regional aquifer and local Perched aquifer have been delineated in the study area. The regional aquifer was identified at about 100 m depth around lowland areas, although prone to polluting effects from farming activities, erosion and weathering processes. This study investigated extents of groundwater pollution and permeability of the aquifers from water sample and grain size analyses. Results show porosity ranging from 49 to 50% and hydraulic conductivities as follows: 7.0 m/day for the sandstone of Nsukka Formation, 34.6 m/day for the outcrop of Ajali sandstone and 10.4 m/day for the sandstone at saturated subsurface zone with transmissivity of about 572 m2/day. The results signify that the regional aquifer is recharged by substantial rate of infiltrations vis-a-vis surface outcrops, and is therefore vulnerable to infiltration of pollution plumes. The groundwater is mainly acidic at pH ranging from 5.05 to 7.41 with a mean value of about 6.48, hence the pollution from dissolved iron in many places. Three main water types were identified, namely, Ca-Mg-HCO3, Ca-HCO3-Cl2 and Mg-Na-HCO3-SO4-Cl2 facies, all signifying dominance of groundwater species arising from precipitation recharge. This has resulted in the influences of surface effluents from run off as indicated by nitrate pollution in some areas. Thus, active hydrologic cycle controls the chemical facies in the water resources of the region, and with its hydraulic influence on the landscape, the quality status of groundwater, as well as the growth of agricultural products have been impaired.

Geological principles of exploration for sandstone-hosted uranium deposits

International Nuclear Information System (INIS)

Le Roux, J.P.

1982-10-01

Although the importance of sandstone-hosted uranium deposits has seemingly faded in recent years due to the discovery of large, high -grade deposits elsewhere, a forecasted energy shortage in the near future will probably necessitate a new look at sedimentary basins as a source of uranium. Back-arc basins adjacent to calcalkaline source areas are especially favourable if they are filled with fluvial, post-Devonian sediments. Syn- and post-depositional tectonics play an important role in the sedimentation-mineralisation process and should be investigated. The oxidation-reduction state of the sandstones is a valid prospecting tool. Sedimentological environments govern the permeability and vegetal matter content of sandstones and directly control uranium mineralisation

Zeolites with Continuously Tuneable Porosity**

Science.gov (United States)

Wheatley, Paul S; Chlubná-Eliášová, Pavla; Greer, Heather; Zhou, Wuzong; Seymour, Valerie R; Dawson, Daniel M; Ashbrook, Sharon E; Pinar, Ana B; McCusker, Lynne B; Opanasenko, Maksym; Čejka, Jiří; Morris, Russell E

2014-01-01

Zeolites are important materials whose utility in industry depends on the nature of their porous structure. Control over microporosity is therefore a vitally important target. Unfortunately, traditional methods for controlling porosity, in particular the use of organic structure-directing agents, are relatively coarse and provide almost no opportunity to tune the porosity as required. Here we show how zeolites with a continuously tuneable surface area and micropore volume over a wide range can be prepared. This means that a particular surface area or micropore volume can be precisely tuned. The range of porosity we can target covers the whole range of useful zeolite porosity: from small pores consisting of 8-rings all the way to extra-large pores consisting of 14-rings. PMID:25284344

Analyzing the Sand-fixing Effect of Feldspathic Sandstone from the Texture Characteristics

Science.gov (United States)

Zhang, lu; Ban, Jichang

2018-01-01

The purpose of this research was aimed to study the sand fixing effect of feldspathic sandstone in Mu Us Sandy Land, to provide a scienticic basis for desertification control, soil and water conservation and development of farming there. Methods of mixing feldspathic sandstone and aeolian sandy soil according to 1: 0, 1: 1, 1: 2, 1: 5, and 0: 1 mass ratioes, the graded composition and characteristics were studied with laser particle size analyzer. The result showed that these features of sand-based, loosely structured, easy to wind erosion of aeolian sandy soil were changed before feldspathic sandstone and aeolian sandy soil compounding. The <0.05 mm particle mass increased with feldspathic sandstone mass increasing. The texture presented this kind of change from sand to sandy loam to loam to silt loam. The small particle size distribution, good homogeneity and other features of aeolian sandy soil were improved to a certain degree, and the particle size distribution became broad before feldspathic sandstone and aeolian sandy soil compounding. The particle grading was continuous, and the grading characteristic was good when m(F): m(S) was 1: 5(Cu was 54.71 and Cc was 2.54) or when m(F): m(S) was 1: 2(Cu was 76.21, Cc was 1.12). The conclusion is that feldspathic sandstone has sand-fixing effect in texture characteristics, which heightens with feldspathic sandstone mass increasing, and when the mass ratio of feldspathic sandstone: aeolian sandy soil is 1: 2 or 1: 5 which compound better.

Sedimentology and Reservoir Characteristics of Early Cretaceous Fluvio-Deltaic and Lacustrine Deposits, Upper Abu Gabra Formation, Sufyan Sub-basin, Muglad Rift Basin, Sudan

Science.gov (United States)

Yassin, Mohamed; Abdullatif, Osman; Hariri, Mustafa

2017-04-01

Sufyan Sub-basin is an East-West trending Sub-basin located in the northwestern part of the Muglad Basin (Sudan), in the eastern extension of the West and Central Africa Rift System (WCARS). The Early Cretaceous Abu Gabra Formation considered as the main source rock in the Muglad Basin. In Sufyan Sub-basin the Early Cretaceous Upper Abu Gabra Formation is the main oil-producing reservoir. It is dominated by sandstone and shales deposited in fluvio-deltaic and lacustrine environment during the first rift cycle in the basin. Depositional and post-depositional processes highly influenced the reservoir quality and architecture. This study investigates different scales of reservoir heterogeneities from macro to micro scale. Subsurface facies analysis was analyzed based on the description of six conventional cores from two wells. Approaches include well log analysis, thin sections and scanning electron microscope (SEM) investigations, grain-size, and X-ray diffraction (XRD) analysis of the Abu Gabra sandstone. The cores and well logs analyses revealed six lithofacies representing fluvio-deltaic and lacustrine depositional environment. The sandstone is medium to coarse-grained, poorly to moderately sorted and sub-angular to subrounded, Sub-feldspathic arenite to quartz arenite. On macro-scale, reservoir quality varies within Abu Gabra reservoir where it shows progressive coarsening upward tendencies with different degrees of connectivity. The upper part of the reservoir showed well connected and amalgamated sandstone bodies, the middle to lower parts, however, have moderate to low sandstone bodies' connectivity and amalgamation. On micro-scale, sandstone reservoir quality is directly affected by textures and diagenesis.The XRD and SEM analyses show that kaolinite and chlorite clay are the common clay minerals in the studied samples. Clay matrix and quartz overgrowth have significantly reduced the reservoir porosity and permeability, while the dissolution of feldspars

ANALYSIS OF OIL-BEARING CRETACEOUS SANDSTONE HYDROCARBON RESERVOIRS, EXCLUSIVE OF THE DAKOTA SANDSTONE, ON THE JICARILLA APACHE INDIAN RESERVATION, NEW MEXICO

International Nuclear Information System (INIS)

Jennie Ridgley

2000-01-01

An additional 450 wells were added to the structural database; there are now 2550 wells in the database with corrected tops on the Juana Lopez, base of the Bridge Creek Limestone, and datum. This completes the structural data base compilation. Fifteen oil and five gas fields from the Mancos-ElVado interval were evaluated with respect to the newly defined sequence stratigraphic model for this interval. The five gas fields are located away from the structural margins of the deep part of the San Juan Basin. All the fields have characteristics of basin-centered gas and can be considered as continuous gas accumulations as recently defined by the U.S. Geological Survey. Oil production occurs in thinly interbedded sandstone and shale or in discrete sandstone bodies. Production is both from transgressive and regressive strata as redefined in this study. Oil production is both stratigraphically and structurally controlled with production occurring along the Chaco slope or in steeply west-dipping rocks along the east margin of the basin. The ElVado Sandstone of subsurface usage is redefined to encompass a narrower interval; it appears to be more time correlative with the Dalton Sandstone. Thus, it was deposited as part of a regressive sequence, in contrast to the underlying rock units which were deposited during transgression

Porosity development in the Copper Ridge Dolomite and Maynardville Limestone, Bear Creek Valley and Chestnut Ridge, Tennessee

International Nuclear Information System (INIS)

Goldstrand, P.M.; Menefee, L.S.; Dreier, R.B.

1995-12-01

Matrix porosity data from deep core obtained in Bear Creek Valley indicate that porosities in the Maynardville Limestone are lithology and depth dependent. Matrix porosities are greater in the Cooper Ridge Dolomite than in the Maynardville Limestone, yet there is no apparent correlation with depth. Two interrelated diagenetic processes are the major controlling factors on porosity development in the Copper Ridge Dolomite and Maynardville Limestone; dissolution of evaporate minerals and dedolomitization. Both of these diagenetic processes produce matrix porosities between 2.1 and 1.3% in the Copper Ridge Dolomite and upper part of the Maynardville Limestone (Zone 6) to depths of approximately 600 ft bgs. Mean matrix porosities in Zones 5 through 2 of the Maynardville Limestone range from 0.8 to 0.5%. A large number of cavities have been intersected during drilling activities in nearly all zones of the Maynardville Limestone in Bear Creek Valley. Therefore, any maynardville Limestone zone within approximately 200 ft of the ground surface is likely to contain cavities that allow significant and rapid flow of groundwater. Zone 6 could be an important stratigraphic unit in the Maynardville Limestone for groundwater flow and contaminant transport because of the abundance of vuggy and moldic porosities. There are large variations in the thickness and lithology in the lower part of the Maynardville (Zones 2, 3, and 4 in the Burial Grounds region). The direction and velocity of strike-parallel groundwater flow may be altered in this area within the lower Maynardville Limestone

Cense Explosion Test Program. Report 1. Cense 1. Explosions in Sandstone

Science.gov (United States)

1977-09-01

series, "Analysis and Summary of CENSE Data." 10 * _ CHAPTER 2 APPROACH 2.1 DESCRIPTION OF TEST SITE An exposed outcrop of Kayenta sandstone with 180...ft/s seismic velocity previously determined (References 12-14) for the unweathered upper zone of the Kayenta sandstone. 16 I The P-wave propagation...Propagation along the horizontal radial was 8400 ft/s. The seismic velocity pre- viously determined for Kayenta sandstone in this area was 7500 ft/s

Brief analysis on relationship between red beds and sandstone-type uranium ore-formation

International Nuclear Information System (INIS)

Ji Zengxian

2006-01-01

Red beds are sandy gravel beds deposited under the arid and hot climates and correspondent to the oxidation environment of continental basins. As an exogenetic epigenetic uranium deposit, the formation of the sandstone-type uranium deposit needs a large chronologic gap between the diagenesis and the subsequent uranium metallogenesis of the ore-hosting target layer with a sedimentary discontinuity and an alternative humid-arid climate. Red beds are the product of this time. The evolutionary times of red beds are in accordance with the formation of the sandstone-type uranium deposit. Both domestic and abroad researches indicate that each times evolution of a red bed might be associated with uranium ore-formation in one or more sandstone layers in the region. In China, red beds are developed in many geologic periods, but sandstone-type uranium mineralization occurs mostly in Mesozoic-Cenozoic. Taking five known sandstone-type uranium deposits as examples, the author makes a primary analysis on the relationship between red beds and the subsequent sandstone-type uranium mineralization. It is suggested that the deposition of red beds and sandstone-type uranium metallogenesis are of 'cogenesis and coexistence' and that the deposition of red beds and its evolutionary times can be regarded as the prerequisites to judge the potential of sandstone-type uranium mineralization in a Mesozoic-Cenozoic sedimentary basin. (authors)

Investigation of water and CO2 (carbon dioxide) flooding using micro-CT (micro-computed tomography) images of Berea sandstone core using finite element simulations

International Nuclear Information System (INIS)

Gunde, Akshay C.; Bera, Bijoyendra; Mitra, Sushanta K.

2010-01-01

The present study reports a numerical investigation of water and CO 2 (carbon dioxide) flooding at the pore scale of a porous medium. We use high resolution micro-computed tomography (micro-CT) images of Berea sandstone core to obtain the pore geometry. The numerical solution used for the simulation was carried out by a finite element based software package. Level Set method is used to determine the position of the interface between two immiscible fluids when oil is displaced by water and CO 2 , respectively. The present formulation is validated against single-phase flow through the porous structure. It is found that, fluid flow inside the pore space takes place through preferential inlet and outlet pores. For two-phase flow, it is observed that continuous displacement of oil occurs during water flooding but CO 2 is able to displace oil at certain locations in the pores. Also, the separation of flow front is observed in the case of CO 2 flooding. A quantitative comparison of the results obtained in two types of flooding simulations suggests that water displaces a higher volume of oil than CO 2 in the time period for which the simulations are performed.

Sandstone landforms shaped by negative feedback between stress and erosion

Czech Academy of Sciences Publication Activity Database

Bruthans, J.; Soukup, J.; Vaculíková, J.; Filippi, Michal; Schweigstillová, Jana; Mayo, A. L.; Mašín, D.; Kletetschka, Günther; Řihošek, J.

2014-01-01

Roč. 7, č. 8 (2014), s. 597-601 ISSN 1752-0894 R&D Projects: GA ČR GA13-28040S Institutional support: RVO:67985831 ; RVO:67985891 Keywords : sandstone * sandstone landsforms * stress * erosion Subject RIV: DB - Geology ; Mineralogy Impact factor: 11.740, year: 2014

Characterizing flow pathways in a sandstone aquifer: Tectonic vs sedimentary heterogeneities

Science.gov (United States)

Medici, G.; West, L. J.; Mountney, N. P.

2016-11-01

Sandstone aquifers are commonly assumed to represent porous media characterized by a permeable matrix. However, such aquifers may be heavy fractured when rock properties and timing of deformation favour brittle failure and crack opening. In many aquifer types, fractures associated with faults, bedding planes and stratabound joints represent preferential pathways for fluids and contaminants. In this paper, well test and outcrop-scale studies reveal how strongly lithified siliciclastic rocks may be entirely dominated by fracture flow at shallow depths (≤ 180 m), similar to limestone and crystalline aquifers. However, sedimentary heterogeneities can primarily control fluid flow where fracture apertures are reduced by overburden pressures or mineral infills at greater depths. The Triassic St Bees Sandstone Formation (UK) of the East Irish Sea Basin represents an optimum example for study of the influence of both sedimentary and tectonic aquifer heterogeneities in a strongly lithified sandstone aquifer-type. This fluvial sedimentary succession accumulated in rapidly subsiding basins, which typically favours preservation of complete depositional cycles including fine grained layers (mudstone and silty sandstone) interbedded in sandstone fluvial channels. Additionally, vertical joints in the St Bees Sandstone Formation form a pervasive stratabound system whereby joints terminate at bedding discontinuities. Additionally, normal faults are present through the succession showing particular development of open-fractures. Here, the shallow aquifer (depth ≤ 180 m) was characterized using hydro-geophysics. Fluid temperature, conductivity and flow-velocity logs record inflows and outflows from normal faults, as well as from pervasive bed-parallel fractures. Quantitative flow logging analyses in boreholes that cut fault planes indicate that zones of fault-related open fractures characterize 50% of water flow. The remaining flow component is dominated by bed-parallel fractures

Effects of network dissolution changes on pore-to-core upscaled reaction rates for kaolinite and anorthite reactions under acidic conditions

KAUST Repository

Kim, Daesang; Lindquist, W. Brent

2013-01-01

new connections. The computed changes were based upon a mineral map from an X-ray computed tomography image of a sandstone core. We studied the effect of these changes on upscaled (pore-scale to core-scale) reaction rates and compared against

Characterization of the porosity distribution in the upper part of the karst Biscayne aquifer using common offset ground penetrating radar, Everglades National Park, Florida

Science.gov (United States)

Mount, Gregory J.; Comas, Xavier; Cunningham, Kevin J.

2014-07-01

The karst Biscayne aquifer is characterized by a heterogeneous spatial arrangement of porosity and hydraulic conductivity, making conceptualization difficult. The Biscayne aquifer is the primary source of drinking water for millions of people in south Florida; thus, information concerning the distribution of karst features that concentrate the groundwater flow and affect contaminant transport is critical. The principal purpose of the study was to investigate the ability of two-dimensional ground penetrating radar (GPR) to rapidly characterize porosity variability in the karst Biscayne aquifer in south Florida. An 800-m-long GPR transect of a previously investigated area at the Long Pine Key Nature Trail in Everglades National Park, collected in fast acquisition common offset mode, shows hundreds of diffraction hyperbolae. The distribution of diffraction hyperbolae was used to estimate electromagnetic (EM) wave velocity at each diffraction location and to assess both horizontal and vertical changes in velocity within the transect. A petrophysical model (complex refractive index model or CRIM) was used to estimate total bulk porosity. A set of common midpoint surveys at selected locations distributed along the common-offset transect also were collected for comparison with the common offsets and were used to constrain one-dimensional (1-D) distributions of porosity with depth. Porosity values for the saturated Miami Limestone ranged between 25% and 41% for common offset GPR surveys, and between 23% and 39% for common midpoint GPR surveys. Laboratory measurements of porosity in five whole-core samples from the saturated part of the aquifer in the study area ranged between 7.1% and 41.8%. GPR estimates of porosity were found to be valid only under saturated conditions; other limitations are related to the vertical resolution of the GPR signal and the volume of the material considered by the measurement methodology. Overall, good correspondence between GPR estimates and

Sandstone compaction under actively controlled uniaxial strain conditions - an experimental study on the causes of subsidence in the Dutch Wadden Area

Science.gov (United States)

Hol, Sander; Mossop, Antony; van der Linden, Arjan; Zuiderwijk, Pedro; Makurat, Axel; van Eijs, Rob

2016-04-01

In the Wadden Sea, a tidal-flat area located between the North Sea and the Dutch mainland shore, and UNESCO World Heritage site, subsidence could potentially impact the ecological system. To guide the licensing process governing gas extraction for the area by a solid understanding of the system's response to production, Nederlandse Aardolie Maatschappij (NAM) has carried out a study on the magnitudes, timing, and mechanisms of subsidence related to gas production. As part of this study program, we address the effect of production-induced reservoir compaction, using core samples from the Moddergat field located at the Wadden Sea coastline, from a depth of ~3800 m TVDSS, to assess the nature of the compaction mechanisms that operate. In this contribution, we focus on the uniaxial strain response of Permian, Aeolian sandstone to pore pressure depletion. As the majority of experiments reported in the literature are conducted under triaxial stress conditions, this data set is somewhat unique, and can help confirm the validity of micromechanical processes found for triaxial stress conditions. We report over 30 data sets of experiments carried out using 1.0 and 1.5 inch diameter plugs, sub-sampled from the extracted sandstone core material. The experiments start at in-situ conditions of pore pressure (Pf=~57 MPa), stress (Sv=~80 MPa, Sh=~67 MPa) and temperature (T up to 100 °C), and deplete to a pore pressure of 3 MPa, under actively controlled lateral constraint boundary conditions (i.e. uniaxial strain). Care was taken to systematically vary porosity and sample morphology to ensure representation of the intra-reservoir variability. Our laboratory data show that pressure-depletion results in a strain in the range of 5·10-3-1·10-2 over the total duration of the experiments of 5-12 weeks, with approximately 80% of the total strain response being close to instantaneous, and 20% developing over time. The total strain response develops during depletion as a result of

On the migration of uranium isotopes in sandstone aquifers

International Nuclear Information System (INIS)

Froehlich, K.; Gellermann, R.

1982-01-01

Measurements of natural 238 U and 234 U activity in groundwater of sandstone aquifers have been used to study the migration of these uranium isotopes. Regarding the uranium exchange between liquid phase and rock surface during migration, two different models were applied for evaluating the experimental results. Values of corresponding parameters (retardation factor K, removal rate R) reflecting different behaviour concerning this exchange were determined. For example, the values obtained for 238 U in a Triassic sandstone aquifer of the GDR are K = 8.6 x 10 6 and R = 1.3 x 10 -3 a -1 , respectively. It was found that, under the conditions of the sandstone aquifer concerned, the removal rate model is better suited for calculating uranium-isotope migration in groundwater. (author)

Effective Wettability Measurements of CO2-Brine-Sandstone System at Different Reservoir Conditions

Science.gov (United States)

Al-Menhali, Ali; Krevor, Samuel

2014-05-01

, core-scale effective contact angle can be determined. In addition to providing a quantitative measure of the core-averaged wetting properties, the technique allows for the observation of shifts in contact angle with changing conditions. We examine the wettability changes of the CO2-brine system in Berea sandstone with variations in reservoir conditions including supercritical, gaseous and liquid CO2injection. We evaluate wettability variation within a single rock with temperature, pressure, and salinity across a range of conditions relevant to subsurface CO2 storage. This study will include results of measurements in a Berea sandstone sample across a wide range of conditions representative of subsurface reservoirs suitable for CO2 storage (5-20 MPa, 25-90 oC, 0-5 mol kg-1). The measurement uses X-ray CT imaging in a state of the art core flooding laboratory designed to operate at high temperature, pressure, and concentrated brines.

Greybull Sandstone Petroleum Potential on the Crow Indian Reservation, South-Central Montana

Energy Technology Data Exchange (ETDEWEB)

Lopez, David A.

2002-05-13

The focus of this project was to explore for stratigraphic traps that may be present in valley-fill sandstone at the top of the Lower Cretaceous Kootenai Formation. This sandstone interval, generally known as the Greybull Sandstone, has been identified along the western edge of the reservation and is a known oil and gas reservoir in the surrounding region. The Greybull Sandstone was chosen as the focus of this research because it is an excellent, well-documented, productive reservoir in adjacent areas, such as Elk Basin; Mosser Dome field, a few miles northwest of the reservation; and several other oil and gas fields in the northern portion of the Bighorn Basin.

3D-printing porosity: A new approach to creating elevated porosity materials and structures.

Science.gov (United States)

Jakus, A E; Geisendorfer, N R; Lewis, P L; Shah, R N

2018-05-01

We introduce a new process that enables the ability to 3D-print high porosity materials and structures by combining the newly introduced 3D-Painting process with traditional salt-leaching. The synthesis and resulting properties of three 3D-printable inks comprised of varying volume ratios (25:75, 50:50, 70:30) of CuSO 4 salt and polylactide-co-glycolide (PLGA), as well as their as-printed and salt-leached counterparts, are discussed. The resulting materials are comprised entirely of PLGA (F-PLGA), but exhibit porosities proportional to the original CuSO 4 content. The three distinct F-PLGA materials exhibit average porosities of 66.6-94.4%, elastic moduli of 112.6-2.7 MPa, and absorbency of 195.7-742.2%. Studies with adult human mesenchymal stem cells (hMSCs) demonstrated that elevated porosity substantially promotes cell adhesion, viability, and proliferation. F-PLGA can also act as carriers for weak, naturally or synthetically-derived hydrogels. Finally, we show that this process can be extended to other materials including graphene, metals, and ceramics. Porosity plays an essential role in the performance and function of biomaterials, tissue engineering, and clinical medicine. For the same material chemistry, the level of porosity can dictate if it is cell, tissue, or organ friendly; with low porosity materials being far less favorable than high porosity materials. Despite its importance, it has been difficult to create three-dimensionally printed structures that are comprised of materials that have extremely high levels of internal porosity yet are surgically friendly (able to handle and utilize during surgical operations). In this work, we extend a new materials-centric approach to 3D-printing, 3D-Painting, to 3D-printing structures made almost entirely out of water-soluble salt. The structures are then washed in a specific way that not only extracts the salt but causes the structures to increase in size. With the salt removed, the resulting medical polymer

Discussion on distribution characteristics of calcareous sandstone in Shihongtan uranium deposit and its genesis

International Nuclear Information System (INIS)

Zhu Huanqiao; Qiao Haiming; Jia Heng; Xu Gaozhong

2007-01-01

Based on the observation and statistics on the calcareous sandstone in the ore host layer in Shihongtan uranium deposit, this paper finds that the calcareous sandstone occurs on and off near the top or wash surface of the sandbody as beads-strings lens along the layer and concentrates in the area where the ore bodies are rich. In lithology, the calcareous sandstone is of coarse grain and fairly well sorted. According to the analysis on the lithogeochemical features and the carbon and oxygen isotopes of calcareous sandstones, it is realized that there some genetic relation between the formation of calcareous sandstone and uranium mineralization in the oxidation-deoxidation transitional belt, that is the precipitation and enrichment of uranium is accompanied by the deposition of carbonate and formation of calcareous sandstone. (authors)

Estimation of Potential Carbon Dioxide Storage Capacities of Onshore Sedimentary Basins in Republic of Korea

Science.gov (United States)

Park, S.; Kim, J.; Lee, Y.

2010-12-01

The potential carbon dioxide storage capacities of the five main onshore sedimentary basins (Chungnam, Gyeongsang, Honam, Mungyeong, and Taebaeksan Basins) in Republic of Korea are estimated based on the methods suggested by the United States National Energy Technology Laboratory (NETL). The target geologic formations considered for geologic storage of carbon dioxide in the sedimentary basins are sandstone and coal beds. The density of carbon dioxide is set equal to 446.4 kg/m3. The adsorption capacity and density of coal (anthracite) are set equal to 2.71 × 10-2 kg/kg and 1.82 × 103 kg/m3, respectively. The average storage efficiency factors for sandstone and coal are set equal to 2.5% and 34.0%, respectively. The Chungnam Basin has the sandstone volume of 72 km3 and the coal volume of 1.24 km3. The average porosity of sandstone in the Chungnam Basin is 3.8%. As a result, the potential carbon dioxide storage capacities of sandstone and coal in the Chungnam Basin are estimated to be 31 Mton and 21 Mton, respectively. The Gyeongsang Basin has the sandstone volume of 1,960 km3. The average porosity of sandstone in the Gyeongsang Basin is 4.6%. As a result, the potential carbon dioxide storage capacity of sandstone in the Gyeongsang Basin is estimated to be 1,011 Mton. The Honam Basin has the sandstone volume of 8 km3 and the coal volume of 0.27 km3. The average porosity of sandstone in the Honam Basin is 1.9%. As a result, the potential carbon dioxide storage capacities of sandstone and coal in the Honam Basin are estimated to be 2 Mton and 5 Mton, respectively. The Mungyeong Basin has the sandstone volume of 60 km3 and the coal volume of 0.66 km3. The average porosity of sandstone in the Mungyeong Basin is 2.0%. As a result, the potential carbon dioxide storage capacities of sandstone and coal in the Mungyeong Basin are estimated to be 13 Mton and 11 Mton, respectively. The Taebaeksan Basin has the sandstone volume of 71 km3 and the coal volume of 0.73 km3. The

A complex investigation of building sandstones from Saxony (Germany)

International Nuclear Information System (INIS)

Goetze, Jens; Siedel, Heiner

2007-01-01

The present paper provides a methodology for the investigation and characterization of building sandstones. This analytical scheme was designed for distinguishing mature arenites, which in general show very similar properties and are difficult to distinguish. This is shown for Cretaceous sandstones from various occurrences in Saxony (Germany), which have been used for centuries as building materials. The procedure is mainly based on the combination of macroscopic rock description, thin section polarizing microscopy (phase composition, texture, grain-size distribution) and cathodoluminescence (CL) microscopy (quartz types, feldspar and kaolinite content) coupled with image analysis, scanning electron microscopy (accessories, pore cement, diagenetic grain surface features), and analysis of pore space data. Sometimes, additional data from X-ray diffraction or chemical analyses (major and trace elements) can be used. Especially in the case of quartz rich arenites, CL is a powerful tool for provenance analysis. The detailed analysis of sandstone material in most cases allows us to assign historically used building material to a specific sandstone occurrence. These results are important for both interpreting the weathering behaviour of the building material and the conservation, reconstruction and stone replacement of historical monuments

Optimization of the injection molding process for development of high performance calcium oxide -based ceramic cores

Science.gov (United States)

Zhou, P. P.; Wu, G. Q.; Tao, Y.; Cheng, X.; Zhao, J. Q.; Nan, H.

2018-02-01

The binder composition used for ceramic injection molding plays a crucial role on the final properties of sintered ceramic and to avoid defects on green parts. In this study, the effects of binder compositions on the rheological, microstructures and the mechanical properties of CaO based ceramic cores were investigated. It was found that the optimized formulation for dispersant, solid loading was 1.5 wt% and 84 wt%, respectively. The microstructures, such as porosity, pore size distribution and grain boundary density were closely related to the plasticizer contents. The decrease of plasticizer contents can enhance the strength of the ceramic cores but with decreased shrinkage. Meanwhile, the creep resistance of ceramic cores was enhanced by decreasing of plasticizer contents. The flexural strength of the core was found to decrease with the increase of the porosity, the improvement of creep resistance is closely related to the decrease of porosity and grain boundary density.

On the Modelling of Algal Biofouling Growth on Nano-TiO2 Coated and Uncoated Limestones and Sandstones

Directory of Open Access Journals (Sweden)

Lorenzo Graziani

2018-02-01

Full Text Available Algal biofouling on archaeological and historic materials, as well as in modern building façade, is a common phenomenon that occurs when microorganisms of various nature adhere to the material, forming biological stains and patinas. It can significantly deteriorate the aesthetic and even mechanical quality of historic and archaeological artifacts. Thus, predicting the colonization progress of algae on treated and untreated materials can be helpful to establish appropriate schedules and methods of maintenance. In this way, the aim of this research was to modelize the algal colonization on nano-TiO2 coated and uncoated stone surfaces, usually found in historic and archaeological artifacts, by following Avrami’s theory. Particular attention was paid on correlating the model with some properties of the substrate, like roughness and porosity. Biofouling was tested on two sandstones and three limestone with different intrinsic characteristics (porosity, roughness by means of an accelerated lab-scale test. A suspension of green alga Chlorella mirabilis and cyanobacteria Chroococcidiopsis fissurarum was used as biofouling. Digital image analysis was carried out in order to find the attachment rate and the growth of algal spots. Results show that the attachment specific rate increased linearly with time, and the assumption of a constant growth rate was acceptable. A good agreement between the simulation and the experimental results was obtained with a maximum error of 0.59%.

Effects of Pisha sandstone content on solute transport in a sandy soil.

Science.gov (United States)

Zhen, Qing; Zheng, Jiyong; He, Honghua; Han, Fengpeng; Zhang, Xingchang

2016-02-01

In sandy soil, water, nutrients and even pollutants are easily leaching to deeper layers. The objective of this study was to assess the effects of Pisha sandstone on soil solute transport in a sandy soil. The miscible displacement technique was used to obtain breakthrough curves (BTCs) of Br(-) as an inert non-adsorbed tracer and Na(+) as an adsorbed tracer. The incorporation of Pisha sandstone into sandy soil was able to prevent the early breakthrough of both tracers by decreasing the saturated hydraulic conductivity compared to the controlled sandy soil column, and the impeding effects increased with Pisha sandstone content. The BTCs of Br(-) were accurately described by both the convection-dispersion equation (CDE) and the two-region model (T-R), and the T-R model fitted the experimental data slightly better than the CDE. The two-site nonequilibrium model (T-S) accurately fit the Na(+) transport data. Pisha sandstone impeded the breakthrough of Na(+) not only by decreasing the saturated hydraulic conductivity but also by increasing the adsorption capacity of the soil. The measured CEC values of Pisha sandstone were up to 11 times larger than those of the sandy soil. The retardation factors (R) determined by the T-S model increased with increasing Pisha sandstone content, and the partition coefficient (K(d)) showed a similar trend to R. According to the results of this study, Pisha sandstone can successfully impede solute transport in a sandy soil column. Copyright © 2015 Elsevier Ltd. All rights reserved.

Characterization of the Lower Cambrian sandstone aquifer in the Swedish Baltic Sea area - assessment regarding its potential suitability for storage of CO2

Science.gov (United States)

Erlström, M.; Sivhed, U.

2012-04-01

In the Baltic region the Cambrian sandstone is considered to have great economic value concerning its aquifer and reservoir properties. Its potential as petroleum reservoir is well known, especially from the Polish, Lithuanian and Russian sectors of the Baltic Sea where oil and gas has been found in anticline traps in the sandstone sequence. Offshore exploration in the Swedish sector has so far not encountered any significant findings of oil and gas. However, the extensive exploration has generated data, which is now being used for assessing the overall properties regarding suitability for storage of CO2. The Swedish primary industry has a great interest in finding potential sites for storage of CO2. A suitable site in the Baltic Sea would be a most favourable alternative in comparison to more remote alternatives such as deep saline aquifers in the North Sea. The Lower Cambrian is in the Swedish sector of the Baltic Sea composed of three main sandstone units varying in thickness between 5 and 50 m occurring within an up to 250 m thick Cambrian sequence dominated by fine-grained terriclastic sediments. The limit of Lower Palaeozoic sequence in the Baltic area is today defined by erosional truncation because of the gently dipping Lower Palaeozoic sequence. To the north and northwest, the limit is found in the Pre-Quaternary, whereas the erosional limit is deeply buried beneath Permian and Mesozoic sediments to the south. Here the Lower Palaeozoic limit is buried to depths reaching more than 2 km. The Cambrian sequence in the distal parts of the Swedish sector occurs at depths of c. 1300 m while it constitutes the bedrock surface in a narrow zone trending from Öland to the north of of Gotland. Sandstone beds constitute 40-60% of the total Cambrian sequence. The main sandstone units have a regional distribution of several thousands of square kilometres. The up to 50 m thick Faludden sandstone member exhibits the best reservoir properties including porosities in the

Geophysical signature recognition of aquifuge and relatively impermeable interbed in ore-hosting sandstone layer at sandstone-type uranium deposit

International Nuclear Information System (INIS)

Zhao Xigang; Wu Hanning; Bai Guanjun; Zhu Huanqiao; Jia Heng

2006-01-01

Geophysical signature recognition of aquifuge and relatively impermeable interbed in ore-hosting aquifer has been carried out a Shihongtan uranium deposit by using comprehensive logging data. The spatial distribution of above aquifuge and impermeable interbed is discussed, and the relation of these layers to sandstone-type uranium deposit, and their impact to in-situ leach mining technology are discussed. It is suggested that the aquifuge and relatively impermeable interbed bring about significant effect to the formation of interlayer oxidation zone sandstone-type uranium deposit, as well as to in-situ leach mining of the deposit. (authors)

Final Report

Energy Technology Data Exchange (ETDEWEB)

Issen, Kathleen [Clarkson Univ., Potsdam, NY (United States)

2017-06-05

This project employed a continuum approach to formulate an elastic constitutive model for Castlegate sandstone. The resulting constitutive framework for high porosity sandstone is thermodynamically sound, (i.e., does not violate the 1st and 2nd law of thermodynamics), represents known material constitutive response, and is able to be calibrated using available mechanical response data. To authenticate the accuracy of this model, a series of validation criteria were employed, using an existing mechanical response data set for Castlegate sandstone. The resulting constitutive framework is applicable to high porosity sandstones in general, and is tractable for scientists and researchers endeavoring to solve problems of practical interest.

Temperature effect on microstructure and P-wave propagation in Linyi sandstone

International Nuclear Information System (INIS)

Sun, Hui; Sun, Qiang; Deng, Wenni; Zhang, Weiqiang; Lü, Chao

2017-01-01

Highlights: • Mass loss rate, P-wave velocity change rate and damage factor increase exponentially as temperatures rise. • The damage threshold temperature of sandstone samples is 300 °C and limit temperature is 900 °C. • P-wave velocity change rate of sandstone exhibits excellent linearity with mass loss rate. • Damage factor can be well expressed by mass loss rate. - Abstract: In order to study the effect of high temperature on the sandstone, scanning electron microscope (SEM) experiments and primary wave (P-wave) velocity tests have been carried out on sandstone specimens heated to different temperature. The results showed that: (1) the mass loss rate increases exponentially with the increase of temperature and reaches 2.97% at 900 °C; (2) the P-wave velocity change rate increases exponentially with the increase of temperature while there is some fluctuation before 500 °C; (3) the damage threshold temperature of sandstone samples is 300 °C and the limit temperature is 900 °C; (4) there is a good linear relationship between the mass loss rate and the P-wave velocity change rate, and the correlation coefficient (R) of the fitting line is 0.989; (5) the damage caused by high temperature can be reflected better by the mass loss rate than P-wave velocity change rate. The results obtained in this paper will be good for predicting the properties of sandstone when exposed to high temperature.

Characteristics and model of sandstone type uranium deposit in south of Songliao basin

International Nuclear Information System (INIS)

Yu Wenbin; Yu Zhenqing

2010-01-01

Through analyzing the uranium deposit tectonic environment, upper cretaceous sequence stratigraphy, depositional system, evolutionary characteristics of sand bodies, the effect of subsequent transformation and the characteristic of uranium deposit, the sandstone type uranium deposit in southern basin is different from typical interlayer oxidation zone sandstone type uranium deposit. The formation and evolution of sandstone-type uranium deposit are controlled by structure fensters; the favorable sedimentary facies type is braided river facies, and the ore body is braided river sand body. The size of uranium deposits is controlled by the local oxidation zone with the characteristics of sandstone type uranium deposit in partial oxidation zone. Uranium ore bodies which distribute in the roof wings of structure fenstes, and occur in gray layers between the upper and lower oxidation zone, showing tabular, and the plate of uranium ore body is controlled by the local oxidation zone. Based on the geological features of sandstone-type uranium deposits, the metallogenic model of local oxidation zones sandstone-type uranium deposits has been set up in the south of Songliao Baisn. (authors)

Paleokarst and reservoir porosity in the Ordovician Beekmantown Dolomite of the central Appalachian basin

Science.gov (United States)

Smosna, R.; Bruner, K.R.; Riley, R.A.

2005-01-01

A karst-unconformity play at the top of the Ordovician Beekmantown Dolomite is judged to have great petroleum potential in Ohio and adjacent states; wells have high ultimate reserves and large areas remain untested. To better understand the origin, development, and distribution of Beekmantown porosity, we conducted a petrologic-stratigraphic study of cores and thin sections from 15 oil and gas wells. The massive dolomite, characterized by a hypidiotopic-idiotopic texture, formed by the replacement of stacked peritidal carbonate cycles. Secondary porosity occurs at two scales: (1) mesoscopic - breccia porosity, solution-enlarged fractures, large vugs, and caverns, and (2) microscopic - intercrystalline, intracrystalline, molds, small vugs, and microfractures. Mesoscopic pores (providing the major storage capacity in this reservoir) were produced by intrastratal solution and collapse of carbonate layers, whereas microscopic pores (connecting the larger pores) generally formed by the leaching of individual carbonate grains and crystals. Most pore types developed during periods of subaerial exposure across the carbonate bank, tied to either the numerous, though brief falls of relative sea level during Beekmantown deposition or more importantly the prolonged Knox unconformity at the close of sedimentation. The distribution of reservoir-quality porosity is quite heterogeneous, being confined vertically to a zone immediately below the unconformity and best developed laterally beneath buried hills and noses of this erosion surface. The inferred, shallow flow of ground water in the Beekmantown karst, primarily below topographic highs and above a diagenetic base level close to the water table, led to this irregular distribution of porosity.

Controlling porosity of porous carbon cathode for lithium oxygen batteries: Influence of micro and meso porosity

Science.gov (United States)

Kim, Minjae; Yoo, Eunjoo; Ahn, Wha-Seung; Shim, Sang Eun

2018-06-01

In rechargeable lithium-oxygen (Li-O2) batteries, the porosity of porous carbon materials plays a crucial role in the electrochemical performance serving as oxygen diffusion path and Li ion transfer passage. However, the influence of optimization of porous carbon as an air electrode on cell electrochemical performance remains unclear. To understand the role of carbon porosity in Li-O2 batteries, carbon materials featuring controlled pore sizes and porosity, including C-800 (nearly 96% microporous) and AC-950 (55:45 micro/meso porosity), are designed and synthesized by carbonization using a triazine-based covalent organic polymer (TCOP). We find that the microporous C-800 cathode allows 120 cycles with a limited capacity of 1000 mAh g-1, about 2 and 10 times higher than that of mixed-porosity AC-950 and mesoporous CMK-3, respectively. Meanwhile, the specific discharge capacity of the C-800 electrode at 200 mA g-1 is 6003 mAh g-1, which is lower than that of the 8433 and 9960 mAh g-1 when using AC-950 and CMK-3, respectively. This difference in the electrochemical performance of the porous carbon cathode with different porosity causes to the generation and decomposition of Li2O2 during the charge and discharge cycle, which affects oxygen diffusion and Li ion transfer.

Apparatus for the measurement of radionuclide transport rates in rock cores

International Nuclear Information System (INIS)

Weed, H.C.; Koszykowski, R.F.; Dibley, L.L.; Murray, I.

1981-09-01

An apparatus and procedure for the study of radionuclide transport in intact rock cores are presented in this report. This equipment more closely simulates natural conditions of radionuclide transport than do crushed rock columns. The apparatus and the procedure from rock core preparation through data analysis are described. The retardation factors measured are the ratio of the transport rate of a non-retarded radionuclide, such as 3 H, to the transport rate of a retarded radionuclide. Sample results from a study of the transport of /sup 95m/Tc and 85 Sr in brine through a sandstone core are included

Data Qualification Report: Calculated Porosity and Porosity-Derived Values for Lithostratigraphic Units for use on the Yucca Mountain Project

Energy Technology Data Exchange (ETDEWEB)

P. Sanchez

2001-05-30

The qualification is being completed in accordance with the Data Qualification Plan DQP-NBS-GS-000006, Rev. 00 (CRWMS M&O 2001). The purpose of this data qualification activity is to evaluate for qualification the unqualified developed input and porosity output included in Data Tracking Number (DTN) M09910POROCALC.000. The main output of the analyses documented in DTN M09910POROCALC.000 is the calculated total porosity and effective porosity for 40 Yucca Mountain Project boreholes. The porosity data are used as input to Analysis Model Report (AMR) 10040, ''Rock Properties Model'' (MDL-NBS-GS-000004, Rev. 00), Interim Change Notice [ICN] 02 (CRWMS M&O 2000b). The output from the rock properties model is used as input to numerical physical-process modeling within the context of a relationship developed in the AMR between hydraulic conductivity, bound water and zeolitic zones for use in the unsaturated zone model. In accordance with procedure AP-3.15Q, the porosity output is not used in the direct calculation of Principal Factors for post-closure safety or disruptive events. The original source for DTN M09910POROCALC.000 is a Civilian Radioactive Waste Management System (CRWMS) Management and Operating Contractor (M&O) report, ''Combined Porosity from Geophysical Logs'' (CRWMS M&O 1999a and hereafter referred to as Rael 1999). That report recalculated porosity results for both the historical boreholes covered in Nelson (1996), and the modern boreholes reported in CRWMS M&O (1996a,b). The porosity computations in Rael (1999) are based on density-porosity mathematical relationships requiring various input parameters, including bulk density, matrix density and air and/or fluid density and volumetric water content. The main output is computed total porosity and effective porosity reported on a foot-by-foot basis for each borehole, although volumetric water content is derived from neutron data as an interim output. This qualification

Data Qualification Report: Calculated Porosity and Porosity-Derived Values for Lithostratigraphic Units for use on the Yucca Mountain Project

International Nuclear Information System (INIS)

P. Sanchez

2001-01-01

The qualification is being completed in accordance with the Data Qualification Plan DQP-NBS-GS-000006, Rev. 00 (CRWMS M and O 2001). The purpose of this data qualification activity is to evaluate for qualification the unqualified developed input and porosity output included in Data Tracking Number (DTN) M09910POROCALC.000. The main output of the analyses documented in DTN M09910POROCALC.000 is the calculated total porosity and effective porosity for 40 Yucca Mountain Project boreholes. The porosity data are used as input to Analysis Model Report (AMR) 10040, ''Rock Properties Model'' (MDL-NBS-GS-000004, Rev. 00), Interim Change Notice [ICN] 02 (CRWMS M and O 2000b). The output from the rock properties model is used as input to numerical physical-process modeling within the context of a relationship developed in the AMR between hydraulic conductivity, bound water and zeolitic zones for use in the unsaturated zone model. In accordance with procedure AP-3.15Q, the porosity output is not used in the direct calculation of Principal Factors for post-closure safety or disruptive events. The original source for DTN M09910POROCALC.000 is a Civilian Radioactive Waste Management System (CRWMS) Management and Operating Contractor (M and O) report, ''Combined Porosity from Geophysical Logs'' (CRWMS M and O 1999a and hereafter referred to as Rael 1999). That report recalculated porosity results for both the historical boreholes covered in Nelson (1996), and the modern boreholes reported in CRWMS M and O (1996a,b). The porosity computations in Rael (1999) are based on density-porosity mathematical relationships requiring various input parameters, including bulk density, matrix density and air and/or fluid density and volumetric water content. The main output is computed total porosity and effective porosity reported on a foot-by-foot basis for each borehole, although volumetric water content is derived from neutron data as an interim output. This qualification report uses

Characterization of the Oriskany and Berea Sandstones: Evaluating Biogeochemical Reactions of Potential Sandstone–Hydraulic Fracturing Fluid Interaction

Energy Technology Data Exchange (ETDEWEB)

Verba, Circe [National Energy Technology Lab. (NETL), Albany, OR (United States); Harris, Aubrey [National Energy Technology Lab. (NETL), Albany, OR (United States)

2016-07-07

, guar gum, and isopropanol]; 3) reviews the known research about the interactions between several hydraulic fracturing chemicals [e.g. polyacrylamide, ethylene glycol, poly(diallyldimethylammonium chloride), and glutaraldehyde] with the minerals (quartz, clay, pyrite, and carbonates) common to the lithologies of the Marcellus shale and its surrounding sandstones; and 4) characterizes the Berea sandstone and analyzes the physical and chemical effects of flowing guar gum through a Berea sandstone core.

Geochemistry of Mariano lake-lake valley cores, McKinley County, New Mexico

International Nuclear Information System (INIS)

Leventhal, J.S.; Lichte, F.E.; Gent, C.A.

1990-01-01

The primary goal of the U.S. Geological Survey-Bureau of Indian Affairs drilling project in the Upper Jurassic Morrison Formation in McKinley County, New Mexico, was to better understand the relationship between host-rock stratigraphy and uranium mineralization. As part of this project, geochemical studies of approximately 280 samples from 8 cores and 1 outcrop were undertaken; samples from 4 cores show uranium enrichment. Geochemical relationships between samples of weathered outcrop, oxidized core, reduced (unmineralized) core, and ore-bearing core were contrasted by comparison of element abundances. Special comparative studies of sandstone and clay chemistry were made using results from x-ray diffraction, optical petrography, and chemical analysis. Results of these studies are discussed

Study of the residual porosity in fuel plate cores based on U3O8 - Al dispersions

International Nuclear Information System (INIS)

Durazzo, M.

2005-01-01

The residual porosity in the meat of nuclear dispersion fuel plates, the fabrication voids, explains the corrosion behaviour of the meats when exposed to the water used as coolant and moderator of MTR type research reactors. The fabrication voids also explain variations in irradiation performance of many fuel dispersion for nuclear reactors. To obtain improved corrosion and irradiation performance, we must understand the fabrication factors that control the amount of void volume in fuel plate meats. The purpose of this study was to investigate the void content of aluminum-base dispersion-type U 3 O 8 -Al fuel plates depending on the characteristics of the starting fuel dispersion used to produce the fuel meat, which is fabricated by pressing. The void content depends on the U 3 O 8 concentration. For a particular U 3 O 8 content, the rolling process establishes a constant void concentration, which is called equilibrium porosity. The equilibrium quantity of voids is insensitive to the initial density of the fuel compact. (author)

Pore Structure and Diagenetic Controls on Relative Permeability: Implications for Enhanced Oil Recovery and CO2 Storage

Science.gov (United States)

Feldman, J.; Dewers, T. A.; Heath, J. E.; Cather, M.; Mozley, P.

2016-12-01

Multiphase flow in clay-bearing sandstones of the Morrow Sandstone governs the efficiency of CO2 storage and enhanced oil recovery at the Farnsworth Unit, Texas. This formation is the target for enhanced oil recovery and injection of one million metric ton of anthropogenically-sourced CO2. The sandstone hosts eight major flow units that exhibit distinct microstructural characteristics due to diagenesis, including: "clean" macro-porosity; quartz overgrowths constricting some pores; ghost grains; intergranular porosity filled by microporous authigenic clay; and feldspar dissolution. We examine the microstructural controls on macroscale (core scale) relative permeability and capillary pressure behavior through: X-ray computed tomography, Robomet.3d, and focused ion beam-scanning electron microscopy imaging of the pore structure of the major flow units of the Morrow Sandstone; relative permeability and capillary pressure in the laboratory using CO2, brine, and oil at reservoir pressure and effective stress conditions. The combined data sets inform links between patterns of diagenesis and multiphase flow. These data support multiphase reservoir simulation and performance assessment by the Southwest Regional Partnership on Carbon Sequestration (SWP). Funding for this project is provided by the U.S. Department of Energy's National Energy Technology Laboratory through the SWP under Award No. DE-FC26-05NT42591. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Controls on the quality of Miocene reservoirs, southern Gulf of Mexico

Science.gov (United States)

Gutiérrez Paredes, Hilda Clarisa; Catuneanu, Octavian; Hernández Romano, Ulises

2018-01-01

An investigation was conducted to determine the main controls on the reservoir quality of the middle and upper Miocene sandstones in the southern Gulf of Mexico based on core descriptions, thin section petrography and petrophysical data; as well as to explore the possible link between the sequence stratigraphic framework, depositional facies and diagenetic alterations. The Miocene deep marine sandstones are attributed to the falling-stage, lowstand, and transgressive systems tracts. The middle Miocene falling-stage systems tract includes medium-to very fine-grained, and structureless sandstones deposited in channels and frontal splays, and muddy sandstones, deposited in lobes of debrites. The lowstand and transgressive systems tracts consist of medium-to very fine-grained massive and normally graded sandstones deposited in channel systems within frontal splay complexes. The upper Miocene falling-stage systems tract includes medium-to coarse-grained, structureless sandstones deposited in channel systems and frontal splay, as well as lobes of debrites formed by grain flows and hybrid-flow deposits. The lowstand and transgressive systems tracts include fine-grained sandstones deposited in overbank deposits. The results reveal that the depositional elements with the best reservoir quality are the frontal splays deposited during the falling-stage system tracts. The reservoir quality of the Miocene sandstones was controlled by a combination of depositional facies, sand composition and diagenetic factors (mainly compaction and calcite cementation). Sandstone texture, controlled primarily by depositional facies appears more important than sandstone composition in determining reservoir quality; and compaction was more important than cementation in porosity destruction. Compaction was stopped, when complete calcite cementation occurred.

GREYBULL SANDSTONE PETROLEUM POTENTIAL ON THE CROW INDIAN RESERVATION, SOUTH-CENTRAL MONTANA

Energy Technology Data Exchange (ETDEWEB)

David A. Lopez

2000-12-14

Evaluation of the Lower Cretaceous Greybull Sandstone on the Crow Indian Reservation for potential stratigraphic traps in the valley-fill sandstone was the focus of this project. The Crow Reservation area, located in south-central Montana, is part of the Rocky Mountain Foreland structural province, which is characterized by Laramide uplifts and intervening structural basins. The Pryor and Bighorn mountains, like other foreland uplifts, are characterized by asymmetrical folds associated with basement-involved reverse faults. The reservation area east of the mountains is on the northwestern flank of the Powder River Basin. Therefore, regional dips are eastward and southeastward; however, several prominent structural features interrupt these regional dips. The nearly 4,000 mi{sup 2} reservation is under explored but has strong potential for increased oil and gas development. Oil and gas production is well established in the Powder River Basin of Wyoming to the south as well as in the areas north and west of the reservation. However, only limited petroleum production has been established within the reservation. Geologic relations and trends indicate strong potential for oil and gas accumulations, but drilling has been insufficient for their discovery. The Greybull Sandstone, which is part of the transgressive systems tract that includes the overlying Fall River Sandstone, was deposited on a major regional unconformity. The erosional surface at the base of the Greybull Sandstone is the +100 Ma, late Aptian-Early Albian regional unconformity of Weimer (1984). This lowstand erosional surface was controlled by a basin-wide drop in sea level. In areas where incised Greybull channels are absent, the lowstand erosional unconformity is at the base of the Fall River Sandstone and equivalent formations. During the pre-Greybull lowstand, sediment bypassed this region. In the subsequent marine transgression, streams began to aggrade and deposit sand of the lower Greybull Sandstone

Numerical simulation of roadway support in a sandstone-type uranium mine

International Nuclear Information System (INIS)

Liu Huipeng; Li Yu; Song Lixia

2009-01-01

At present, the most surrounding rocks of sandstone-type uranium mines in China are mudstone, sandstone, pelitic siltstone, and so on. They show the characteristics of soft rock. Such uranium deposit is not fit for in-situ leaching. If the uranium ores are mined by conventional mining method, one of the problems to be solved is the support technique in the soft rock roadway. So, taking a uranium mine in Inner Mongolia as the research object, the support technique in the soft rock roadway of the sandstone-type uranium deposits is studied. Through on-site engineering geological investigation and laboratory test, the main reasons for roadway damage are analyzed. A technique of support in the soft rock roadway of sandstone-type uranium deposits is put forward by drawing on the expericnce of soft rock roadway support in coal mines. The roadway shape and support parameters are optimized by using a numerical simulation method. The results verified the feasibility of the supporting technique. (authors)

Sediment transport direction in fluviatile Karharbari sandstone, Giridih Basin, Bihar

Energy Technology Data Exchange (ETDEWEB)

Tewari, R C; Casshyap, S M

1978-01-01

The sandstone is pebbly, very coarse grained in the lower part, and coarse to medium grained in the upper part. Shale and coal respectively constitute 9 and 5% of the strata Small and large erosional channels and successive sets of large scale cross-bedding characterize the sandstone. Palaeo- currents reveal that the paleodrainage and sediment transport were dominantly directed from SSW to NNE.

Traces of the heritage arising from the Macelj sandstone

Science.gov (United States)

Golež, Mateja

2014-05-01

The landscape of Southeast Slovenia and its stone heritage principally reveal itself through various Miocene sandstones. The most frequently found type on the borderline between Slovenia and Croatia, i.e. east of Rogatec, is the micaceous-quartz Macelj sandstone. This rock ranges in colour from greenish grey to bluish grey and yellowish, depending on the content of glauconite, which colours it green. In its composition, the rock is a heterogeneous mixture of grains of quartz, dolomite, muscovite, microcline, anorthite and glauconite. The average size of grains is 300μm. In cross-section, they are oblong, semi-rounded or round. The mechanical-physical and durability properties of the Macelj sandstone, which have been characterised pursuant to the applicable standards for natural stone, reveal that the rock exhibits poor resistance to active substances from the atmosphere, particularly in the presence of salt. In the surroundings of Rogatec, there are around 45 abandoned quarries of the Macelj sandstone, which are the result of the exploitation of this mineral resource from the 17th century on. The local quarrymen earned their bread until 1957, when the Kambrus quarry industry closed down. From the original use of this mineral resource as construction and decorative material, the useful value of the Macelj sandstone expanded during the development of the metals industry to the manufacture of large and small grindstones for the needs of the domestic and international market. Therefore, traces of quarrying can not only be seen in the disused quarries, but also in the rich architectural heritage of Rogatec and its surroundings, the stone furniture - from portals, window frames, wells, various troughs, pavements to stone walls - and other. The living quarrying heritage slowly passed into oblivion after World War II, although the analysis of the social image of the people residing in Rogatec and its surroundings revealed that there was an average of one stonemason in

SALTSTONE VARIABILITY STUDY - MEASUREMENT OF POROSITY

International Nuclear Information System (INIS)

Harbour, J; Vickie Williams, V; Tommy Edwards, T; Russell Eibling, R; Ray Schumacher, R

2007-01-01

One of the goals of the Saltstone Variability Study is to identify the operational and compositional variables that control or influence the important processing and performance properties of Saltstone mixes. One of the key performance properties is porosity which is a measure of the volume percent of a cured grout that is occupied by salt solution (for the saturated case). This report presents (1) the results of efforts to develop a method for the measurement of porosity of grout samples and (2) initial results of porosity values for samples that have been previously produced as part of the Saltstone Variability Study. A cost effective measurement method for porosity was developed that provides reproducible results, is relatively fast (30 to 60 minutes per sample) and uses a Mettler Toledo HR83 Moisture Analyzer that is already operational and routinely calibrated at Aiken County Technology Laboratory. The method involves the heating of the sample at 105 C until no further mass loss is observed. This mass loss value, which is due to water evaporation, is then used to calculate the volume percent porosity of the mix. The results of mass loss for mixes at 105 C were equivalent to the results obtained using thermal gravimetric analysis. The method was validated by comparing measurements of mass loss at 105 C for cured portland cement in water mixes to values presented in the literature for this system. A stereopycnometer from Quantachrome Instruments was selected to measure the cured grout bulk densities. Density is a property that is required to calculate the porosities. A stereopycnometer was already operational at Aiken County Technology Laboratory, has been calibrated using a solid stainless steel sphere of known volume, is cost effective and fast (∼15 minutes per sample). Cured grout densities are important in their own right because they can be used to project the volume of waste form produced from a given amount of salt feed of known composition. For mixes

Porosity Prediction of Plain Weft Knitted Fabrics

Directory of Open Access Journals (Sweden)

Muhammad Owais Raza Siddiqui

2014-12-01

Full Text Available Wearing comfort of clothing is dependent on air permeability, moisture absorbency and wicking properties of fabric, which are related to the porosity of fabric. In this work, a plug-in is developed using Python script and incorporated in Abaqus/CAE for the prediction of porosity of plain weft knitted fabrics. The Plug-in is able to automatically generate 3D solid and multifilament weft knitted fabric models and accurately determine the porosity of fabrics in two steps. In this work, plain weft knitted fabrics made of monofilament, multifilament and spun yarn made of staple fibers were used to evaluate the effectiveness of the developed plug-in. In the case of staple fiber yarn, intra yarn porosity was considered in the calculation of porosity. The first step is to develop a 3D geometrical model of plain weft knitted fabric and the second step is to calculate the porosity of the fabric by using the geometrical parameter of 3D weft knitted fabric model generated in step one. The predicted porosity of plain weft knitted fabric is extracted in the second step and is displayed in the message area. The predicted results obtained from the plug-in have been compared with the experimental results obtained from previously developed models; they agreed well.

Middle Ordovician brachiopods from the Stairway Sandstone, Amadeus Basin, central Australia

DEFF Research Database (Denmark)

Jakobsen, Kristian Grube; Brock, Glenn A.; Nielsen, Arne Thorshøj

2014-01-01

-water palaeoenvironment along the margin of northeastern Gondwana. The brachiopods from the Stairway Sandstone are of low diversity and represent ca 9% of the entire shelly fauna. Five brachiopod taxa are described from the Stairway Sandstone; all are endemic to the Amadeus Basin at species level. Two new species...

Application potential of sequence stratigraphy to prospecting for sandstone-type uranium deposit in continental depositional basins

International Nuclear Information System (INIS)

Li Shengxiang; Chen Zhaobo; Chen Zuyi; Xiang Weidong; Cai Yuqi

2001-01-01

Sequence stratigraphy has been widely used in hydrocarbon exploration and development, and great achievements have been achieved. However, its application to the prospecting for sandstone-type uranium deposits is just beginning. The metallogenic characteristics of sandstone-type uranium deposits and those of oil and gas are compared, and the relationship between sandstone-type uranium metallogenesis and the system tracts of sequence stratigraphy is studied. The authors propose that highest and system tracts are the main targets for prospecting interlayer oxidation zone type sandstone uranium deposits, and the incised valleys of low stand system tracts are favourable places for phreatic oxidation zone type sandstone uranium deposits, and transgressive system tracts are generally unfavorable to the formation of in-situ leachable sandstone-type uranium deposits. Finally, the authors look ahead the application potential of sequence stratigraphy to the prospecting for sandstone-type uranium deposits in continental depositional basins

Porosity and Health: Perspective of Traditional Persian Medicine

Science.gov (United States)

Tafazoli, Vahid; Nimrouzi, Majid; Daneshfard, Babak

2016-01-01

Background: The authors of this manuscript aimed to show the importance of porosity and condensation in health according to traditional Persian medicine (TPM) with consideration of new evidence in conventional medicine. Methods: Cardinal traditional medical and pharmacological texts were searched for the traditional terms of takhalkhol (porosity) and takassof (condensity) focused on preventive methods. The findings were classified and compared with new medical findings. Results: According to traditional Persian medicine, porosity and condensity are the two crucial items that contribute to human health. Somatotype is a taxonomy based on embryonic development, which may be considered in parallel with porosity and condensation. However, these terms are not completely the same. There are many causes for acquired porosity comprising hot weather, too much intercourse, rage, starvation, and heavy exercises. In general, porosity increases the risk of diseases as it makes the body organs vulnerable to external hot and cold weather. On the other hand, the porose organs are more susceptible to accumulation of morbid matters because the cellular wastes cannot be evacuated in the normal way. There are some common points between traditional and conventional medicine in the context of porosity and condensity. The relation between diet and somatotype is an example. Conclusion: Condensity and porosity are the two basic items cited in the TPM resources and contribute to health maintenance and disease prevention of body organs. Creating a balance between these two states in different body organs, strongly contributes to disease prevention, treatment and diminishing chronic diseases period. Choosing proper modality including diet, drug therapy, and manual therapy depends on the amount porosity and stiffness of the considered organ and the preferred porosity of the affected organ keeping in a normal healthy state. PMID:27840513

Discussion on metallogenic prospect of sandstone-type uranium deposit in Yabulai basin

International Nuclear Information System (INIS)

Wang Lianshe; Li Xiangping

2003-01-01

Based on characteristics of initial basin type and tectonic reworking process, this article analyses the distribution features of depositional system and subsequent alteration of the target horizon of sandstone-type uranium deposits in Yabulai basin. Guided by prognostic criteria of sandstone-type uranium deposits, authors suggest that the post-depositional tectonic reworking in the basin was quite intense, and uranium metallogenic prospects are unfavorable. However, the Lower Cretaceous in the paleo-slope at the middle of the basin does show certain metallogenic prospects for sandstone-type uranium deposits

Multidisciplinary studies on ancient sandstone quarries of Western Sardinia (Italy).

Science.gov (United States)

Grillo, Silvana Maria; Del Vais, Carla; Naitza, Stefano

2013-04-01

The ancient coastal quarries of Mediterranean are increasingly considered geosites of multidisciplinary relevance. They are sites of historical-archaeological interest that show ancient techniques of stone extraction; they are significant for cultural heritage conservation and restoration, as sources of the stones used in ancient buildings and monuments; they are sites of geological relevance, as often retain important stratigraphic sections; they are also useful markers of secular changes in the sea level. A multisciplinary study is in progress on the ancient quarries of the Sinis region (western Sardinia island), integrating archaeological, geological, minero-petrographical data. In Sardinia, coastal quarries have been established from Punic and Roman times. Many of them exploited Quaternary sediments along the southern and western coasts of the island. They consist of middle-late Pleistocene marine conglomerates and carbonate sandstones, and of coastal (aeolian) carbonate sandstones. Sandstone blocks of different sizes have been widely used in ancient cities for buildings, defensive works, harbours, etc. Three main areas of stone extraction (San Giovanni di Sinis, Punta Maimoni, Is Arutas) have been so far recognized in the Sinis. GIS-supported mapping and documentation of the sites includes their geology and stratigraphy, the extension and layout of the quarries, and an evaluation of volumes of extracted rocks. Documented archaeological evidences include ancient extraction fronts, spoil heaps, working areas, working traces in the old fronts, transport routes of blocks, and traces of loading facilities. The study is aimed at reconstructing the relationships of the quarries with the urban areas of Sinis, as the ancient Punic-Roman city of Tharros. Consequently, a minero-petrographical characterization (optical microscopy, XRD) is performed on sandstones sampled in each quarry, and in historical buildings in Tharros and other centres of the region (Cabras

Earth formation porosity log

International Nuclear Information System (INIS)

Smith, H.D.; Smith, M.P.; Schultz, W.E.

1977-01-01

A method for determining the porosity of earth formations in the vicinity of a cased well borehole is described, comprising the steps of: irradiating the earth formations in the vicinity of the cased well borehole with fast neutrons from a source of fast neutrons passed into the borehole; and generating a signal representative of the fast neutron population present in the well borehole at a location in the borehole, the signal is functionally related to the porosity of the earth formations in the vicinity of the borehole

A Porosity Method to Describe Complex 3D-Structures Theory and Application to an Explosion

Directory of Open Access Journals (Sweden)

M.-F. Robbe

2006-01-01

Full Text Available A theoretical method was developed to be able to describe the influence of structures of complex shape on a transient fluid flow without meshing the structures. Structures are considered as solid pores inside the fluid and act as an obstacle for the flow. The method was specifically adapted to fast transient cases.The porosity method was applied to the simulation of a Hypothetical Core Disruptive Accident in a small-scale replica of a Liquid Metal Fast Breeder Reactor. A 2D-axisymmetrical simulation of the MARS test was performed with the EUROPLEXUS code. Whereas the central internal structures of the mock-up could be described with a classical shell model, the influence of the 3D peripheral structures was taken into account with the porosity method. 

Electromagnetic methods for rapidly characterizing porosity distributions in the upper part of the Biscayne aquifer, southern Florida

Science.gov (United States)

Mount, G. J.; Comas, X.; Cunningham, K. J.

2010-12-01

measurements of bulk porosity from the data available, a complex refractive index model (CRIM) was used. This allows for the delineation of the distribution of estimated porosity values from both 1D and 2D velocity models. All data are further constrained with terrain conductivity measurements and porosity values measured from whole-core samples. Porosity estimates calculated using the CRIM, range from about 10 to 45% and strongly correspond with the porosity values from the whole-core samples This study illustrates the potential of electromagnetic methods for quickly mapping areas of enhanced porosity. Furthermore, this information may improve understanding of surface water-groundwater exchange in the Everglades, which is a key component of ongoing and future restoration efforts.

Characteristics of isotope geology of sandstone-type uranium deposit in Turpan-Hami Basin

International Nuclear Information System (INIS)

Liu Hanbin; Xia Yuliang; Lin Jinrong; Fan Guang

2003-01-01

This paper expounds the isotope characteristics of in-situ leachable sandstone-type uranium deposit of Shihongtan in the southwestern part of Turpan-Hami basin. The results suggest that uranium mineralization age of 48 ± 2 Ma and 28 ± 4 Ma are obtained. The ages of the porphyritic granite and gneissic granite from the southwestern area are 422 ± 5 Ma and 268 ± 23 Ma. The U-Pb age of clastic zircons from ore-bearing sandstone is 283 ± 67 Ma, which is corresponding to the age of gneissic granite of the provenance area indicating the material source of uraniferous sandstone.Based. The sources are uraniferous sandstone accumulated during the deposition and the uranium leached from provenance area rocks by weathering. (authors)

Applying reaction condition index to predict sandstone type uranium deposit

International Nuclear Information System (INIS)

Chen Gongxin; Liu Jinhui; Cheng Hai

2002-01-01

On the basic of the explanation of reaction condition index, the deduction of reaction condition index calculation principle, the hydrogeological setting in Gongpoquan basin in Baishan, Gansu province and the study of reaction condition index of its water source point, the north Luotuoquan area in Gongpoquan basin seems to be a favourable place for sandstone type uranium deposit, and the prospect area for sandstone type uranium deposit is delimitated

Mechanistic Effects of Porosity on Structural Composite Materials

Science.gov (United States)

Siver, Andrew

As fiber reinforced composites continue to gain popularity as primary structures in aerospace, automotive, and powersports industries, quality control becomes an extremely important aspect of materials and mechanical engineering. The ability to recognize and control manufacturing induced defects can greatly reduce the likelihood of unexpected catastrophic failure. Porosity is the result of trapped volatiles or air bubbles during the layup process and can significantly compromise the strength of fiber reinforced composites. A comprehensive study was performed on an AS4C-UF3352 TCR carbon fiber-epoxy prepreg system to determine the effect of porosity on flexural, shear, low-velocity impact, and damage residual strength properties. Autoclave cure pressure was controlled to induce varying levels of porosity to construct six laminates with porosity concentrations between 0-40%. Porosity concentrations were measured using several destructive and nondestructive techniques including resin burnoff, sectioning and optical analysis, and X-ray computed tomography (CT) scanning. Ultrasonic transmission, thermography, and CT scanning provided nondestructive imaging to evaluate impact damage. A bilinear relationship accurately characterizes the change in mechanical properties with increasing porosity. Strength properties are relatively unaffected when porosity concentrations are below approximately 2.25% and decrease linearly by up to 40% in high porosity specimens.

Characterization of Rock Mechanical Properties Using Lab Tests and Numerical Interpretation Model of Well Logs

Directory of Open Access Journals (Sweden)

Hao Xu

2016-01-01

Full Text Available The tight gas reservoir in the fifth member of the Xujiahe formation contains heterogeneous interlayers of sandstone and shale that are low in both porosity and permeability. Elastic characteristics of sandstone and shale are analyzed in this study based on petrophysics tests. The tests indicate that sandstone and mudstone samples have different stress-strain relationships. The rock tends to exhibit elastic-plastic deformation. The compressive strength correlates with confinement pressure and elastic modulus. The results based on thin-bed log interpretation match dynamic Young’s modulus and Poisson’s ratio predicted by theory. The compressive strength is calculated from density, elastic impedance, and clay contents. The tensile strength is calibrated using compressive strength. Shear strength is calculated with an empirical formula. Finally, log interpretation of rock mechanical properties is performed on the fifth member of the Xujiahe formation. Natural fractures in downhole cores and rock microscopic failure in the samples in the cross section demonstrate that tensile fractures were primarily observed in sandstone, and shear fractures can be observed in both mudstone and sandstone. Based on different elasticity and plasticity of different rocks, as well as the characteristics of natural fractures, a fracture propagation model was built.

Validating predictions of evolving porosity and permeability in carbonate reservoir rocks exposed to CO2-brine

Science.gov (United States)

Smith, M. M.; Hao, Y.; Carroll, S.

2017-12-01

Improving our ability to better forecast the extent and impact of changes in porosity and permeability due to CO2-brine-carbonate reservoir interactions should lower uncertainty in long-term geologic CO2 storage capacity estimates. We have developed a continuum-scale reactive transport model that simulates spatial and temporal changes to porosity, permeability, mineralogy, and fluid composition within carbonate rocks exposed to CO2 and brine at storage reservoir conditions. The model relies on two primary parameters to simulate brine-CO2-carbonate mineral reaction: kinetic rate constant(s), kmineral, for carbonate dissolution; and an exponential parameter, n, relating porosity change to resulting permeability. Experimental data collected from fifteen core-flooding experiments conducted on samples from the Weyburn (Saskatchewan, Canada) and Arbuckle (Kansas, USA) carbonate reservoirs were used to calibrate the reactive-transport model and constrain the useful range of k and n values. Here we present the results of our current efforts to validate this model and the use of these parameter values, by comparing predictions of extent and location of dissolution and the evolution of fluid permeability against our results from new core-flood experiments conducted on samples from the Duperow Formation (Montana, USA). Agreement between model predictions and experimental data increase our confidence that these parameter ranges need not be considered site-specific but may be applied (within reason) at various locations and reservoirs. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Pore Structure Model for Predicting Elastic Wavespeeds in Fluid-Saturated Sandstones

Science.gov (United States)

Zimmerman, R. W.; David, E. C.

2011-12-01

During hydrostatic compression, in the elastic regime, ultrasonic P and S wave velocities measured on rock cores generally increase with pressure, and reach asymptotic values at high pressures. The pressure dependence of seismic velocities is generally thought to be due to the closure of compliant cracks, in which case the high-pressure velocities must reflect only the influence of the non-closable, equant "pores". Assuming that pores can be represented by spheroids, we can relate the elastic properties to the pore structure using an effective medium theory. Moreover, the closure pressure of a thin crack-like pore is directly proportional to its aspect ratio. Hence, our first aim is to use the pressure dependence of seismic velocities to invert the aspect ratio distribution. We use a simple analytical algorithm developed by Zimmerman (Compressibility of Sandstones, 1991), which can be used for any effective medium theory. Previous works have used overly restrictive assumptions, such as assuming that the stiff pores are spherical, or that the interactions between pores can be neglected. Here, we assume that the rock contains an exponential distribution of crack aspect ratios, and one family of stiff pores having an aspect ratio lying somewhere between 0.01 and 1. We develop our model in two versions, using the Differential Scheme, and the Mori-Tanaka scheme. The inversion is done using data obtained in dry experiments, since pore fluids have a strong effect on velocities and tend to mask the effect of the pore geometry. This avoids complicated joint inversion of dry and wet data, such as done by Cheng and Toksoz (JGR, 1979). Our results show that for many sets of data on sandstones, we can fit very well the dry velocities. Our second aim is to predict the saturated velocities from our pore structure model, noting that at a given differential stress, the pore structure should be the same as for a dry test. Our results show that the Biot-Gassmann predictions always

Characterization Of Core Sample Collected From The Saltstone Disposal Facility

International Nuclear Information System (INIS)

Cozzi, A.; Duncan, A.

2010-01-01

During the month of September 2008, grout core samples were collected from the Saltstone Disposal Facility, Vault 4, cell E. This grout was placed during processing campaigns in December 2007 from Deliquification, Dissolution and Adjustment Batch 2 salt solution. The 4QCY07 Waste Acceptance Criteria sample collected on 11/16/07 represents the salt solution in the core samples. Core samples were retrieved to initiate the historical database of properties of emplaced Saltstone and to demonstrate the correlation between field collected and laboratory prepared samples. Three samples were collected from three different locations. Samples were collected using a two-inch diameter concrete coring bit. In April 2009, the core samples were removed from the evacuated sample container, inspected, transferred to PVC containers, and backfilled with nitrogen. Samples furthest from the wall were the most intact cylindrically shaped cored samples. The shade of the core samples darkened as the depth of coring increased. Based on the visual inspection, sample 3-3 was selected for all subsequent analysis. The density and porosity of the Vault 4 core sample, 1.90 g/cm 3 and 59.90% respectively, were comparable to values achieved for laboratory prepared samples. X-ray diffraction analysis identified phases consistent with the expectations for hydrated Saltstone. Microscopic analysis revealed morphology features characteristic of cementitious materials with fly ash and calcium silicate hydrate gel. When taken together, the results of the density, porosity, x-ray diffraction analysis and microscopic analysis support the conclusion that the Vault 4, Cell E core sample is representative of the expected waste form.

Sedimentological Characteristics and Re-interpretation of the Paleoenvironment of Lokoja Sandstone, Southern Bida Basin, Nigeria

International Nuclear Information System (INIS)

Ojo, O. J.; Akande, S. O.

2002-01-01

Detail mapping of the Lokoja Formation consisting predominantly of sandstones exposed along Okene-Abuja highway near the confluence of Rivers Niger and Benue in the southern Bida Basin was undertaken in an attempt to reconstruct their depositional history. The analyses of the lithofacies characteristics, pebble morphogenesis and ichnofossil content of the Lokoja sandstones in the study area reveal their depositional environments which evolved from alluvial fans through braided stream into nearshore shallow marine conditions. The massive, immature, matrix to grain supported conglomerate subfacies can be interpreted as debris flow. The conglomeratic sandstone facies (massive, cross stratified and graded subfacies) reflect deposits of deep braided channels. The bioturbated and herringbone cross stratified conglomeratic sandstones indicate shallowing to marginal marine environments. The fine to medium grained sandstones, siltstones and claystones are interpreted as channel bars and floodplain deposits.Results of pebble morphogenesis analysis indicate predominance of fluvial processes. Minor high energy (probably beach) condition is indicated by some individual clasts from the conglomeratic sandstone facies with sphericity and OP index values less that 0.66 and -1.5 respectively.The study is significant because it represents the first sedimentological evidence of influence of shallow marine in the development of Lokoja sandstones during Campanian-Maastrichtian times

Failure Forecasting in Triaxially Stressed Sandstones

Science.gov (United States)

Crippen, A.; Bell, A. F.; Curtis, A.; Main, I. G.

2017-12-01

Precursory signals to fracturing events have been observed to follow power-law accelerations in spatial, temporal, and size distributions leading up to catastrophic failure. In previous studies this behavior was modeled using Voight's relation of a geophysical precursor in order to perform `hindcasts' by solving for failure onset time. However, performing this analysis in retrospect creates a bias, as we know an event happened, when it happened, and we can search data for precursors accordingly. We aim to remove this retrospective bias, thereby allowing us to make failure forecasts in real-time in a rock deformation laboratory. We triaxially compressed water-saturated 100 mm sandstone cores (Pc= 25MPa, Pp = 5MPa, σ = 1.0E-5 s-1) to the point of failure while monitoring strain rate, differential stress, AEs, and continuous waveform data. Here we compare the current `hindcast` methods on synthetic and our real laboratory data. We then apply these techniques to increasing fractions of the data sets to observe the evolution of the failure forecast time with precursory data. We discuss these results as well as our plan to mitigate false positives and minimize errors for real-time application. Real-time failure forecasting could revolutionize the field of hazard mitigation of brittle failure processes by allowing non-invasive monitoring of civil structures, volcanoes, and possibly fault zones.

PALEOEVIRONMENT OF NIGERIA'S AJALI SANDSTONES: A ...

African Journals Online (AJOL)

The Ajali Sandstone is a major clastic formation of Campanian-Maastrichtian age occuring within the Anambra Basin, Southeastern Nigeria. ... The result is in line with earlier conclusions of fluvial or fluviodeltaic depositional environment based on analysis of faceis, sedimentary rock which are suitable for morphometrical ...

Assessment of spatial distrilbution of porosity and aquifer geohydraulic parameters in parts of the Tertiary - Quaternary hydrogeoresource of south-eastern Nigeria

Science.gov (United States)

George, N. J.; Akpan, A. E.; Akpan, F. S.

2017-12-01

An integrated attempt exploring information deduced from extensive surface resistivity study in three Local Government Areas of Akwa Ibom State, Nigeria and data from hydrogeological sources obtained from water boreholes have been explored to economically estimate porosity and coefficient of permeability/hydraulic conductivity in parts of the clastic Tertiary - Quaternary sediments of the Niger Delta region. Generally, these parameters are predominantly estimated from empirical analysis of core samples and pumping test data generated from boreholes in the laboratory. However, this analysis is not only costly and time consuming, but also limited in areal coverage. The chosen technique employs surface resistivity data, core samples and pumping test data in order to estimate porosity and aquifer hydraulic parameters (transverse resistance, hydraulic conductivity and transmissivity). In correlating the two sets of results, Porosity and hydraulic conductivity were observed to be more elevated near the riverbanks. Empirical models utilising Archie's, Waxman-Smits and Kozeny-Carman Bear relations were employed characterising the formation parameters with wonderfully deduced good fits. The effect of surface conduction occasioned by clay usually disregarded or ignored in Archie's model was estimated to be 2.58 × 10-5 Siemens. This conductance can be used as a corrective factor to the conduction values obtained from Archie's equation. Interpretation aided measures such as graphs, mathematical models and maps which geared towards realistic conclusions and interrelationship between the porosity and other aquifer parameters were generated. The values of the hydraulic conductivity estimated from Waxman-Smits model was approximately 9.6 × 10-5m/s everywhere. This revelation indicates that there is no pronounced change in the quality of the saturating fluid and the geological formations that serve as aquifers even though the porosities were varying. The deciphered parameter

The Bentheim Sandstone: Geology, petrophysics, varieties and it's use as dimension stone

NARCIS (Netherlands)

Dubelaar, C.W.; Nijland, T.G.

2014-01-01

The shallow-marine Bentheim Sandstone was deposited in one of the NW-SE trending basins north of the London-Brabant and Rhenish massifs during the Valanginian (Early Cretaceous). The Bentheim Sandstone forms an important reservoir rock for petroleum, but has also proven itself as a very durable

Optimization of High Porosity Thermal Barrier Coatings Generated with a Porosity Former

Science.gov (United States)

Medřický, Jan; Curry, Nicholas; Pala, Zdenek; Vilemova, Monika; Chraska, Tomas; Johansson, Jimmy; Markocsan, Nicolaie

2015-04-01

Yttria-stabilized zirconia thermal barrier coatings are extensively used in turbine industry; however, increasing performance requirements have begun to make conventional air plasma sprayed coatings insufficient for future needs. Since the thermal conductivity of bulk material cannot be lowered easily; the design of highly porous coatings may be the most efficient way to achieve coatings with low thermal conductivity. Thus the approach of fabrication of coatings with a high porosity level based on plasma spraying of ceramic particles of dysprosia-stabilized zirconia mixed with polymer particles, has been tested. Both polymer and ceramic particles melt in plasma and after impact onto a substrate they form a coating. When the coating is subjected to heat treatment, polymer burns out and a complex structure of pores and cracks is formed. In order to obtain desired porosity level and microstructural features in coatings; a design of experiments, based on changes in spray distance, powder feeding rate, and plasma-forming atmosphere, was performed. Acquired coatings were evaluated for thermal conductivity and thermo-cyclic fatigue, and their morphology was assessed using scanning electron microscopy. It was shown that porosity level can be controlled by appropriate changes in spraying parameters.

Three-dimensional characterization of microporosity and permeability in fault zones hosted in heterolithic succession

Science.gov (United States)

Riegel, H. B.; Zambrano, M.; Jablonska, D.; Emanuele, T.; Agosta, F.; Mattioni, L.; Rustichelli, A.

2017-12-01

The hydraulic properties of fault zones depend upon the individual contributions of the damage zone and the fault core. In the case of the damage zone, it is generally characterized by means of fracture analysis and modelling implementing multiple approaches, for instance the discrete fracture network model, the continuum model, and the channel network model. Conversely, the fault core is more difficult to characterize because it is normally composed of fine grain material generated by friction and wear. If the dimensions of the fault core allows it, the porosity and permeability are normally studied by means of laboratory analysis or in the other case by two dimensional microporosity analysis and in situ measurements of permeability (e.g. micro-permeameter). In this study, a combined approach consisting of fracture modeling, three-dimensional microporosity analysis, and computational fluid dynamics was applied to characterize the hydraulic properties of fault zones. The studied fault zones crosscut a well-cemented heterolithic succession (sandstone and mudstones) and may vary in terms of fault core thickness and composition, fracture properties, kinematics (normal or strike-slip), and displacement. These characteristics produce various splay and fault core behavior. The alternation of sandstone and mudstone layers is responsible for the concurrent occurrence of brittle (fractures) and ductile (clay smearing) deformation. When these alternating layers are faulted, they produce corresponding fault cores which act as conduits or barriers for fluid migration. When analyzing damage zones, accurate field and data acquisition and stochastic modeling was used to determine the hydraulic properties of the rock volume, in relation to the surrounding, undamaged host rock. In the fault cores, the three-dimensional pore network quantitative analysis based on X-ray microtomography images includes porosity, pore connectivity, and specific surface area. In addition, images were

On the water saturation calculation in hydrocarbon sandstone reservoirs

Energy Technology Data Exchange (ETDEWEB)

Stalheim, Stein Ottar

2002-07-01

The main goal of this work was to identify the most important uncertainty sources in water saturation calculation and examine the possibility for developing new S{sub w} - equations or possibility to develop methods to remove weaknesses and uncertainties in existing S{sub w} - equations. Due to the need for industrial applicability of the equations we aimed for results with the following properties: The accuracy in S{sub w} should increase compared with existing S{sub w} - equations. The equations should be simple to use in petrophysical evaluations. The equations should be based on conventional logs and use as few as possible input parameters. The equations should be numerical stable. This thesis includes an uncertainty and sensitivity analysis of the most common S{sub w} equations. The results are addressed in chapter 3 and were intended to find the most important uncertainty sources in water saturation calculation. To increase the knowledge of the relationship between R{sub t} and S{sub w} in hydrocarbon sandstone reservoirs and to understand how the pore geometry affects the conductivity (n and m) of the rock a theoretical study was done. It was also an aim to examine the possibility for developing new S{sub w} - equations (or investigation an effective medium model) valid inhydrocarbon sandstone reservoirs. The results are presented in paper 1. A new equation for water saturation calculation in clean sandstone oil reservoirs is addressed in paper 2. A recommendation for best practice of water saturation calculation in non water wet formation is addressed in paper 3. Finally a new equation for water saturation calculation in thinly interbedded sandstone/mudstone reservoirs is presented in paper 4. The papers are titled: 1) Is the saturation exponent n a constant. 2) A New Model for Calculating Water Saturation In 3) Influence of wettability on water saturation modeling. 4) Water Saturation Calculations in Thinly Interbedded Sandstone/mudstone Reservoirs. A

On the field determination of effective porosity

International Nuclear Information System (INIS)

Javandel, I.

1989-03-01

Effective porosity of geologic materials is a very important parameter for estimating groundwater travel time and modeling contaminant transport in hydrologic systems. Determination of a representative effective porosity for nonideal systems is a problem still challenging hydrogeologists. In this paper, some of the conventional field geophysical and hydrological methods for estimating effective porosity of geologic materials are reviewed. The limitations and uncertainties associated with each method are discussed. 30 refs., 8 figs

Preliminary study on features of mineralogical zoning of epigenetic alteration at sandstone-type uranium deposit, Dongsheng area, Ordos basin

International Nuclear Information System (INIS)

Xiao Xinjian; Li Ziying; Chen Anping

2004-01-01

Sandstone-type uranium deposits located in Dongsheng area, northern Ordos basin, occur in Zhiluo Formation, Middle Jurassic. The Zhiluo Formation is divided into two members. The lower member is further divided into two submembers. The lower submember is dominantly composed of grey sandstone being the ore-hosting horizon; the upper submember consists of grey-green sandstone and mudstone. The upper member of Zhiluo Formation is made of mottled medium-fine grained sandstone and mudstone. Through the microscopic observation and study on sandstones of Zhiluo Formation, authors have established a vertical zonation of epigenetic alteration (from the top to the bottom): the limonitization + clayization + carbonation in the mottled fine-grained sandstone of the upper member of Zhiluo Formation; the green alteration (II) (mainly the chloritization of biotite, as well as the chloritization and epidotization of feldspar) + clayization + carbonation in the grey-green sandstone of the upper submember of the lower member of Zhiluo Formation; and the green alteration (I) (mainly the epidotization of feldspar) + carbonation in grey, grey-white sandstone of the lower submember. The epigenetic alteration basically occurs in grey-green sandstone. The sandstone shows grey-green color because it contains much green biotite (not chlorite). The epigenetic alteration in sandstone layer is closely associated with the uranium ore-formation

Research on evaluation method for water saturation of tight sandstone in Suxi region

Science.gov (United States)

Lv, Hong; Lai, Fuqiang; Chen, Liang; Li, Chao; Li, Jie; Yi, Heping

2017-05-01

The evaluation of irreducible water saturation is important for qualitative and quantitative prediction of residual oil distribution. However, it is to be improved for the accuracy of experimental measuring the irreducible water saturation and logging evaluation. In this paper, firstly the multi-functional core flooding experiment and the nuclear magnetic resonance centrifugation experiment are carried out in the west of Sulige gas field. Then, the influence was discussed about particle size, porosity and permeability on the water saturation. Finally, the evaluation model was established about irreducible water saturation and the evaluation of irreducible water saturation was carried out. The results show that the results of two experiments are both reliable. It is inversely proportional to the median particle size, porosity and permeability, and is most affected by the median particle size. The water saturation of the dry layer is higher than that of the general reservoir. The worse the reservoir property, the greater the water saturation. The test results show that the irreducible water saturation model can be used to evaluate the water floor.

Pore scale modelling of electrical and hydraulic properties of a semi-consolidated sandstone under unsaturated conditions

Science.gov (United States)

Cassiani, G.; dalla, E.; Brovelli, A.; Pitea, D.; Binley, A. M.

2003-04-01

The development of reliable constitutive laws to translate geophysical properties into hydrological ones is the fundamental step for successful applications of hydrogeophysical techniques. Many such laws have been proposed and applied, particularly with regard to two types of relationships: (a) between moisture content and dielectric properties, and (b) between electrical resistivity, rock structure and water saturation. The classical Archie's law belongs to this latter category. Archie's relationship has been widely used, starting from borehole logs applications, to translate geoelectrical measurements into estimates of saturation. However, in spite of its popularity, it remains an empirical relationship, the parameters of which must be calibrated case by case, e.g. on laboratory data. Pore-scale models have been recently recognized and used as powerful tools to investigate the constitutive relations of multiphase soils from a pore-scale point of view, because they bridge the microscopic and macroscopic scales. In this project, we develop and validate a three-dimensional pore-scale method to compute electrical properties of unsaturated and saturated porous media. First we simulate a random packing of spheres [1] that obeys the grain-size distribution and porosity of an experimental porous medium system; then we simulate primary drainage with a morphological approach [2]; finally, for each state of saturation during the drainage process, we solve the electrical conduction equation within the grain structure with a new numerical model and compute the apparent electrical resistivity of the porous medium. We apply the new method to a semi-consolidated Permo-Triassic Sandstone from the UK (Sherwood Sandstone) for which both pressure-saturation (Van Genuchten) and Archie's law parameters have been measured on laboratory samples. A comparison between simulated and measured relationships has been performed.

Etude de la diagraphie neutron du granite de Beauvoir. Effet neutron des altérations et de la matrice du granite. Calibration granite. Porosité totale à l'eau et porosité neutron Analysis of the Beauvoir Granite Neutron Log. Neutron Effect of Alterations and of the Granite Matrix. Granite Calibration. Total Water Porosity and Neutron Porosity

Directory of Open Access Journals (Sweden)

Galle C.

2006-11-01

carottes (n. Nous montrons que, pour le granite de Beauvoir, l'effet neutron de la matrice est important (en moyenne proche de 7% et ne peut être négligé lorsque l'on mesure des porosités voisines de 0,5% sur carottes. La calibration de l'outil neutron dans le granite et non pas dans des calcaires est d'autre part capitale quant à la précision quantitative des résultats. This article describes the research done on the Beauvoir granite (Echassières GPF 1 borehole, French Massif Central range. The aim of this project was to obtain representative values of the water saturation (n total free water porosity of the Beauvoir granite from PorosityN neutron porosity (BRGM neutron log. The exact knowledge of the porosity of a crystalline block is effectively fundamental to determine its possibilities for being used as a waste storage site. With this goal, neutron logging provides indispensable information concerning the characterization of a porous medium. Our procedure was experimental, and we tried to go more deeply into various problems linked to the use of neutron logging in a granitic rock. Two main factors governed the neutron response : (i the hydrogen concentration of the formation (free water and combined water of various minerals and (ii the presence of absorber elements with a large capture cross-section such as gadolinium, cadmium, boron as well as lithium for the Beauvoir granite. After measuring the Beauvoir granite n total (free water porosity on core samples, we evaluated the combined water content of each sample tested on the basis of fire loss tests on rock powder at 900°C. From the hydrogen atoms volumic concentration, we determined a hydrogen index that we directly converted into the PorosityN(OH- neutron porosity, (by definition, pure water at 20°C has a hydrogen index of 1 which is equivalent to a 100% porosity. For the Beauvoir granite, the matrix combined water represents an average neutron porosity (Table 1 of about 4%. In the second phase, we used

A new bee species that excavates sandstone nests.

Science.gov (United States)

Orr, Michael C; Griswold, Terry; Pitts, James P; Parker, Frank D

2016-09-12

Humanity has long been fascinated by animals with apparently unfavorable lifestyles [1]. Nesting habits are especially important because they can limit where organisms live, thereby driving population, community, and even ecosystem dynamics [2]. The question arises, then, why bees nest in active termite mounds [3] or on the rim of degassing volcanoes, seemingly preferring such hardship [4]. Here, we present a new bee species that excavates sandstone nests, Anthophora (Anthophoroides) pueblo Orr (described in Supplemental Information, published with this article online), despite the challenges already inherent to desert life. Ultimately, the benefits of nesting in sandstone appear to outweigh the associated costs in this system. Copyright © 2016 Elsevier Ltd. All rights reserved.

Zeolites with continuously tuneable porosity

OpenAIRE

Wheatley, Paul S; Chlubná-Eliášová, Pavla; Greer, Heather; Zhou, Wuzong; Seymour, Valerie R; Dawson, Daniel M; Ashbrook, Sharon E; Pinar, Ana B; McCusker, Lynne B; Opanasenko, Maksym; Cejka, Jiří; Morris, Russell E

2014-01-01

Czech Science Foundation. Grant Number: P106/12/G015 Zeolites are important materials whose utility in industry depends on the nature of their porous structure. Control over microporosity is therefore a vitally important target. Unfortunately, traditional methods for controlling porosity, in particular the use of organic structure-directing agents, are relatively coarse and provide almost no opportunity to tune the porosity as required. Here we show how zeolites with a continuously tuneabl...

Determination of the Representative Elementary Volume for the study of sandstones and siltstones by X-Ray microtomography

Directory of Open Access Journals (Sweden)

Jaquiel Salvi Fernandes

2012-08-01

Full Text Available X-Ray computerized microtomography (µ-CT besides providing two-dimensional images (2-D of the transversal sections of the sample, the biggest attraction of the methodology is the rendering of three-dimensional images (3-D, enabling a more real analysis of the porous structure of the rock. However, the reconstruction, visualization and analysis of such 3-D images are limited in computer terms. Thus, it is not always possible to reconstruct the images with the total size of the microtomographed sample. Therefore, this study aims at determining the Representative Elementary Volume (REV in reservoir rocks concerning their porosity. In order to collect microtomographic data from reservoir rocks, a microtomograph Skyscan model 1172 was utilized for the sandstone and siltstone samples scanning. After the analysis of the graphs obtained by REV, it was concluded that the most adequate dimensions for the reconstructed volume in each analyzed sample were approximately 1400 × 1400 × 1400 µm, which are dimensions that can easily be reconstructed, visualized and analyzed.

Corrosion of MTR type fuel plates containing U3O8-Al cermet cores

International Nuclear Information System (INIS)

Durazzo, M.

1985-01-01

The fuel plate samples containing U 3 O 8 -Al cermet cores with concentrations from 10 to 90% of U 3 O 8 weight were fabricated. Samples with 58% of U 3 O 8 eight were fabricated using compacts with densities from 75 to 95% of theoretical density. The influences of U 3 O 8 concentration and porosity of compacted core on porosity and uniformity of core thickness are discussed. The U 3 O 8 -Al cores were submitted to corrosion tests and exposed to deionized water at temperatures of 30, 50, 70 and 90 0 C by cladding deffect produced artificially. The results shown that core corrosion is accompanied by hydrogen release. The total volum of released hydrogen and the time interval to observe the initiation of hydrogen releasing (incubation time) are depending on core pososity and absolute temperature. A mechanism for U 3 O 8 -Al core corrosion process is proposed and discussed. The cladding of fuel plate samples was submitted to corrosion tests under similar conditons of the IAE-R1 reactor operating at 2, 5 and 10 MW. (Author) [pt

Porosity study on free mineral addition cement paste

International Nuclear Information System (INIS)

Salgueiro, W.; Somoza, A.; Cabrera, O.; Consolati, G.

2004-01-01

A study of the hydration process and the porosity evolution in a cement paste is presented. The analysis of porosity was made in samples with water to cement ratios (w/c) of 0.24, 0.40 and 0.60 at age of 3, 7, 28 and 365 days, respectively. Information on the evolution of total porosity and on the strength of the paste were obtained using positron annihilation lifetime spectroscopy (PALS), scanning electron microscopy (SEM), X-ray diffraction (XRD), mechanical tests (compression and flexion) and water absorption techniques. Specifically, positron lifetime technique allowed us to analyze the evolution of gel and capillary porosity during the hydration process. Using a simple function proposed, reasonable fits to the experimental data of the porosity evolution as a function of the compression strength were obtained

Fluvial-deltaic sedimentation and stratigraphy of the ferron sandstone

Science.gov (United States)

Anderson, P.B.; Chidsey, T.C.; Ryer, T.A.

1997-01-01

East-central Utah has world-class outcrops of dominantly fluvial-deltaic Turonian to Coniacian aged strata deposited in the Cretaceous foreland basin. The Ferron Sandstone Member of the Mancos Shale records the influences of both tidal and wave energy on fluvial-dominated deltas on the western margin of the Cretaceous western interior seaway. Revisions of the stratigraphy are proposed for the Ferron Sandstone. Facies representing a variety of environments of deposition are well exposed, including delta-front, strandline, marginal marine, and coastal-plain. Some of these facies are described in detail for use in petroleum reservoir characterization and include permeability structure.

The nature of porosity in organic-rich mudstones of the Upper Jurassic Kimmeridge Clay Formation, North Sea, offshore United Kingdom

Science.gov (United States)

Fishman, Neil S.; Hackley, Paul C.; Lowers, Heather; Hill, Ronald J.; Egenhoff, Sven O.; Eberl, Dennis D.; Blum, Alex E.

2012-01-01

Analyses of organic-rich mudstones from wells that penetrated the Upper Jurassic Kimmeridge Clay Formation, offshore United Kingdom, were performed to evaluate the nature of both organic and inorganic rock constituents and their relation to porosity in this world-class source rock. The formation is at varying levels of thermal maturity, ranging from immature in the shallowest core samples to mature in the deepest core samples. The intent of this study was to evaluate porosity as a function of both organic macerals and thermal maturity. At least four distinct types of organic macerals were observed in petrographic and SEM analyses and they all were present across the study area. The macerals include, in decreasing abundance: 1) bituminite admixed with clays; 2) elongate lamellar masses (alginite or bituminite) with small quartz, feldspar, and clay entrained within it; 3) terrestrial (vitrinite, fusinite, semifusinite) grains; and 4) Tasmanites microfossils. Although pores in all maceral types were observed on ion-milled surfaces of all samples, the pores (largely nanopores with some micropores) vary as a function of maceral type. Importantly, pores in the macerals do not vary systematically as a function of thermal maturity, insofar as organic pores are of similar size and shape in both the immature and mature Kimmeridge rocks. If any organic pores developed during the generation of hydrocarbons, they were apparently not preserved, possibly because of the highly ductile nature of much of the rock constituents of Kimmeridge mudstones (clays and organic material). Inorganic pores (largely micropores with some nanopores) have been observed in all Kimmeridge mudstones. These pores, particularly interparticle (i.e., between clay platelets), and intraparticle (i.e., in framboidal pyrite, in partially dissolved detrital K-feldspar, and in both detrital and authigenic dolomite) are noteworthy because they compose much of the observable porosity in the shales in both

Age, sedimentary environments, and other aspects of sandstone and related host rocks for uranium deposits

International Nuclear Information System (INIS)

1983-01-01

Project II of the Uranium Geology Working Group was assigned to the study of sedimentary basins and sandstone - type uranium deposits. About 40% of the worlds's uranium resources are contained in sandstone-type deposits, which has led to extensive research. The research was carried out mainly by correspondence, and the results reported by 21 geologists from 10 nations are summarized in this report. It investigated five topics dealing with important aspects of the geology of uranium ores in sandstone host formations: age of host rock; partitioning of uranium between continental and marine sediments; latitude limitation on formation of sandstone deposits; effect of rock formation dip on sandstone ores; usefulness of stable isotope and fluid inclusion studies. The results of studies on these subjects form part of a wider programme of the Working Group, whose final results will be presented at the 27th International Geological Congress in Moscow in 1984

Sandstone Relief Geohazards and their Mitigation: Rock Fall Risk Management in the Bohemian Switzerland National Park

Czech Academy of Sciences Publication Activity Database

Vařilová, Zuzana; Zvelebil, J.

2005-01-01

Roč. 44, - (2005), s. 53-58 ISSN 1682-5519. [Sandstone Landscapes in Europe. Past, Present and Future. International Conference on Sandstone Landscapes /2./. Vianden, 25.05.2005-28.05.2005] Keywords : sandstones * rock-slope instability * rock fall * risk evalution and mitigation * monitoring net * remedial works Subject RIV: DO - Wilderness Conservation

Helium measurements of pore fluids obtained from the San Andreas Fault Observatory at Depth (SAFOD, USA) drill cores

Science.gov (United States)

Ali, S.; Stute, M.; Torgersen, T.; Winckler, G.; Kennedy, B. M.

2011-02-01

4He accumulated in fluids is a well established geochemical tracer used to study crustal fluid dynamics. Direct fluid samples are not always collectable; therefore, a method to extract rare gases from matrix fluids of whole rocks by diffusion has been adapted. Helium was measured on matrix fluids extracted from sandstones and mudstones recovered during the San Andreas Fault Observatory at Depth (SAFOD) drilling in California, USA. Samples were typically collected as subcores or from drillcore fragments. Helium concentration and isotope ratios were measured 4-6 times on each sample, and indicate a bulk 4He diffusion coefficient of 3.5 ± 1.3 × 10-8 cm2 s-1 at 21°C, compared to previously published diffusion coefficients of 1.2 × 10-18 cm2 s-1 (21°C) to 3.0 × 10-15 cm2 s-1 (150°C) in the sands and clays. Correcting the diffusion coefficient of 4Hewater for matrix porosity (˜3%) and tortuosity (˜6-13) produces effective diffusion coefficients of 1 × 10-8 cm2 s-1 (21°C) and 1 × 10-7 (120°C), effectively isolating pore fluid 4He from the 4He contained in the rock matrix. Model calculations indicate that <6% of helium initially dissolved in pore fluids was lost during the sampling process. Complete and quantitative extraction of the pore fluids provide minimum in situ porosity values for sandstones 2.8 ± 0.4% (SD, n = 4) and mudstones 3.1 ± 0.8% (SD, n = 4).

Rate type isotach compaction of consolidated sandstone

NARCIS (Netherlands)

Waal, J.A. de; Thienen-Visser, K. van; Pruiksma, J.P.

2015-01-01

Laboratory experiments on samples from a consolidated sandstone reservoir are presented that demonstrate rate type compaction behaviour similar to that observed on unconsolidated sands and soils. Such rate type behaviour can have large consequences for reservoir compaction, surface subsidence and

Particle track membranes with higher porosity

International Nuclear Information System (INIS)

Heinrich, B.; Gemende, B.; Lueck, H.B.

1992-01-01

Possibilities of improvement of flux and dirt loading capacity of particle track membranes have been examined. Three different ways were investigated: using a divergent ion beam for the irradiation; enlarging the surface porosity through a conical pore shape; creating an asymmetrical membrane structure with two different porosities. Mathematical models and experimental results have been discussed. 9 figs, 3 tabs

Porosity Assessment for Different Diameters of Coir Lignocellulosic Fibers

Science.gov (United States)

da Luz, Fernanda Santos; Paciornik, Sidnei; Monteiro, Sergio Neves; da Silva, Luiz Carlos; Tommasini, Flávio James; Candido, Verônica Scarpini

2017-10-01

The application of natural lignocellulosic fibers (LCFs) in engineering composites has increased interest in their properties and structural characteristics. In particular, the inherent porosity of an LCF markedly affects its density and the adhesion to polymer matrices. For the first time, both open and closed porosities of a natural LCF, for different diameter ranges, were assessed. Fibers extracted from the mesocarp of the coconut fruit were investigated by nondestructive methods of density measurements and x-ray microtomography (microCT). It was found that, for all diameter ranges, the closed porosity is significantly higher than the open porosity. The total porosity increases with diameter to around 60% for coir fibers with more than 503 μm in diameter. The amount and characteristics of these open and closed porosities were revealed by t test and Weibull statistics as well as by microCT.

Fast evolving conduits in clay-bonded sandstone: Characterization, erosion processes and significance for the origin of sandstone landforms

Czech Academy of Sciences Publication Activity Database

Bruthans, J.; Svetlik, D.; Soukup, J.; Schweigstillová, Jana; Válek, Jan; Sedláčková, M.; Mayo, A.L.

2012-01-01

Roč. 177, December (2012), s. 178-193 ISSN 0169-555X R&D Projects: GA AV ČR IAA300130806 Institutional support: RVO:67985891 ; RVO:68378297 Keywords : sandstone * erosion * piping * tensile strength * conduit * landform Subject RIV: DA - Hydrology ; Limnology Impact factor: 2.552, year: 2012

Numerical simulation on coolant flow and heat transfer in core

International Nuclear Information System (INIS)

Yao Zhaohui; Wang Xuefang; Shen Mengyu

1997-01-01

To simulate the coolant flow and the heat transfer characteristics of a core, a computer code, THAPMA (Thermal Hydraulic Analysis Porous Medium Analysis) has been developed. In THAPMA code, conservation equations are based on a porous-medium formulation, which uses four parameters, i.e, volume porosity, directional surface porosity, distributed resistance, and distributed heat source (sink), to model the effects of fuel rods and other internal solid structures on flow and heat transfer. Because the scheme and the solution are very important in accuracy and speed of calculation, a new difference scheme (WSUC) has been used in the energy equation, and a modified PISO solution method have been employed to simulate the steady/transient states. The code has been proved reliable and can effectively solve the transient state problem by several numerical tests. According to the design of Qinshan NPP-II, the flow and heat transfer phenomena in reactor core have been numerically simulated. The distributions of the velocity and the temperature can provide a theoretical basis for core design and safety analysis

A special kind of sandstone-type uranium deposit related to Jurassic palaeochannel systems in the northeastern Ordos Basin, China

International Nuclear Information System (INIS)

Li Ziying; Fang Xiheng; Xia Yuliang; Sun Ye; Jiao Yangquan; Chen Anping; Zhang Ke

2010-01-01

Dongsheng sandstone-type uranium deposit is a large one discovered in recent years in the northeastern Ordos Basin, China. It is a special kind of sandstone-type uranium deposit,different from other ordinary sandstone-type deposits because of its unique signatures. It is generally controlled by a transitional zone between greenish and grayish sandstones, both of those two kinds of sandstones now indicate reduced geochemical environments. The greenish color of the palaeo-oxidized sandstones mainly results from chloritization and epidotization related to oil and gas secondary reduction processes. The deposit genetically is different from ordinary sandstone uranium deposits,which is of more complex origin,undergoing not only palaeo-oxidization mineralization process, but also oil-gas fluid and hydrothermal reworking processes. It is spatially related to Jurassic Zhiluo Formation with braided palaeo channel systems. The uranium mineralization zone with higher grade usually exists in the branching area of the distributary channels of main braided streams, whose sandstone heterogeneity shows a transfer sedimentary facies from the braided stream sedimentary system to the braided delta sedimentary system. Statistical results show that medium and fine-grained sandstones are the most favorable rock types for uranium mineralization. (authors)

Plant fibre composites - porosity and volumetric interaction

DEFF Research Database (Denmark)

Madsen, Bo; Thygesen, Anders; Lilholt, Hans

2007-01-01

the combination of a high fibre volume fraction, a low porosity and a high composite density is optimal. Experimental data from the literature on volumetric composition and density of four types of plant fibre composites are used to validate the model. It is demonstrated that the model provides a concept......Plant fibre composites contain typically a relative large amount of porosity, which considerably influences properties and performance of the composites. The large porosity must be integrated in the conversion of weight fractions into volume fractions of the fibre and matrix parts. A model...... is presented to predict the porosity as a function of the fibre weight fractions, and to calculate the related fibre and matrix volume fractions, as well as the density of the composite. The model predicts two cases of composite volumetric interaction separated by a transition fibre weight fraction, at which...

Analysis on metallogenic conditions of paleochannel sandstone type uranium deposits in kelulun region

Energy Technology Data Exchange (ETDEWEB)

Mingyue, Feng [Beijing Research Inst. of Uranium Geology, Beijing (China)

1999-07-01

On the basis of comprehensively analyzing metallogenic conditions of paleochannel sandstone type uranium deposits, the author discusses regional geologic background, characteristics of the basement and sedimentary cover of Kelulun basin and Huchawula-Hulun Lake basin, and the metallogenic potential of paleochannel sandstone type uranium deposits is proposed.

Analysis on metallogenic conditions of paleochannel sandstone type uranium deposits in kelulun region

International Nuclear Information System (INIS)

Feng Mingyue

1999-01-01

On the basis of comprehensively analyzing metallogenic conditions of paleochannel sandstone type uranium deposits, the author discusses regional geologic background, characteristics of the basement and sedimentary cover of Kelulun basin and Huchawula-Hulun Lake basin, and the metallogenic potential of paleochannel sandstone type uranium deposits is proposed

Porosity model for simultaneous radionuclide transfer in compact clay

International Nuclear Information System (INIS)

Grambow, B.; Ribet, S.; Landesman, C.; Altman, S.

2010-01-01

Document available in extended abstract form only. Both, a mono and a dual porosity model have been developed to describe diffusion in bentonite as function of compaction, which give similar results for the diffusion coefficients. There are little advantages but more computation time for the dual porosity model compared to the mono-porosity model. A significant change in paradigm has been proposed to describe diffusion accessible porosity in bentonite: Only a single micro-porosity value is considered for anions, cations and neutral species. Hydration water in the interlayers is considered as part of the solid phase and is not considered as a constitutive part of overall porosity. Since hydration water takes part of the solid phase, it is now possible to explicitly account for retention of HTO by formulating exchange between HTO and water in the interlayers. In the adaptation of the model to experimental data, a single fit constant, the geometric factor G = 7 was used, common to all ions and neutral species and for densities between 0.2 and 1.8 kg.dm -3 . The only input parameters to describe the effect of dry density on diffusion coefficients are the micro porosity (total porosity minus interlayer porosity) and the hydration numbers of exchanging cations in the interlayers, both of which can be measured by independent means (DRX, water sorption isotherms). The modelling of simultaneous mass transfer of HTO, Cs, Br and Ni has been undertaken. From the results apparent diffusion coefficients were obtained. Effective diffusion coefficients can of course only be compared to literature data if the the same porosity hypothesis is used for Da-De conversion as used in literature (total porosity for anions and HTO, micro-porosity for anions). Then, the calculated apparent diffusion coefficients for HTO match closely the measured values in the mentioned density range. Considering large experimental data uncertainty the agreement between anion diffusion data and calculations

The effect of bed non-uniformities and porosity of particles on dryout in boiling particle beds

International Nuclear Information System (INIS)

Macbeth, R.V.; Mogford, D.J.; Willshire, S.J.

1988-03-01

This report relates to an on-going experimental programme concerned with the coolability of beds of reactor core debris or rubble immersed in a liquid coolant, as might occur in an accident situation. The objectives are to develop experimental techniques, improve the understanding of bed cooling mechanisms, determine dry-out limitations of various bed configurations and particle shapes and sizes and devise ways of improving bed coolability. The report concentrates on a recently discovered effect on bed coolability of particle porosity, such as exists in fragmented UO 2 fuel pellets. It is shown that porosity can lower bed dry-out powers by a factor of 4 or 5. A mechanism which explains the effect is presented. The report also gives results of bed non-uniformities obtained by mixing glass particles with the dielectrically heated 'ferrite' particles used in the experiments. (author)

Preliminary analysis of the sandstone accumulation situation at Sha-3 of the Paleogene Series Shakhetsze in the Khekou basin of the Tsziyan region

Energy Technology Data Exchange (ETDEWEB)

Chen, S

1984-01-01

The Khekou basin of the second order which is located in the Eastern part of the Tsziyan basin in the oil and gas Bokhayvan'skiy pool has an area of about 900 km/sup 2/. The main productive level occurs in sandstone beds in the Sha-3 subseries (reaching thickness of about 400 m) of the Shakhetsze series. The Bonan oil field was discovered in this region in 1975. The initially productive deposits were viewed as fluvial-delta; however, studies of recent years, including investigation of the sedimentation sequences and the structures that mark the surfaces of the microscopic level in the core sample, together with an analysis of borehole geophysical data, indicated that the sandy bodies of the productive beds in the basin must be viewed as deposits of turbidite flows and deposits of gravitational flows in channels. Insofar as distribution of the turbidite sandstones differs significantly from the delta, this led to a review of the long-term trends in the neighboring fields.

Analysis on depositional system and prospect of sandstone-type uranium deposits of Bayanhua formation in Yilemen basin

International Nuclear Information System (INIS)

Sun Zexuan; Li Guoxin; He Fayang; Wei Yunjie

2002-01-01

Yilemen basin is a typical Mesozoic intra-mountain one. The author analyses characteristics of depositional system and the prospect of sandstone-type uranium deposit in the sedimentary cover of the Bayanhua Formation, Lower Cretaceous. Authors suggest that the conglomerate, sandstone-conglomerate and sandstone beds of braided stream and delta are favourable horizons for locating phreatic and interlayer oxidation zone sandstone-type uranium deposits, i.e. the northwestern side of Dalai uplifted zone, the Chagantaigebuqi narrow sag, and the southern area of Baolinbuqi

Estimation and measurement of porosity change in cement paste

International Nuclear Information System (INIS)

Lee, Eunyong; Jung, Haeryong; Kwon, Ki-jung; Kim, Do-Gyeum

2011-01-01

Laboratory-scale experiments were performed to understand the porosity change of cement pastes. The cement pastes were prepared using commercially available Type-I ordinary Portland cement (OPC). As the cement pastes were exposed in water, the porosity of the cement pastes sharply increased; however, the slow decrease of porosity was observed as the dissolution period was extended more than 50 days. As expected, the dissolution reaction was significantly influenced by w/c ratio and the ionic strength of solution. A thermodynamic model was applied to simulate the porosity change of the cement pastes. It was highly influenced by the depth of the cement pastes. There was porosity increase on the surface of the cement pastes due to dissolution of hydration products, such as portlandite, ettringite, and CSH. However, the decrease of porosity was estimated inside the cement pastes due to the precipitation of cement minerals. (author)

Diagenesis and reservoir properties of Cretaceous-Lower Tertiary sandstones: the GANT-1 well, western Nuussuaq, central West Greenland

Energy Technology Data Exchange (ETDEWEB)

Kierkegaard, Thomas

1998-08-01

The main purpose of this study is to describe the diagenetic alterations occurring in the Cretaceous to Lower Paleocene sedimentary succession of the GANT-1 well, and to determine the diagenetic and detrital factors which control present porosity and permeability. The GANT-1 well is located on north-western Nuussuaq, central West Greenland. The West Greenland margin is a continental margin subdivided into linked basins where Cretaceous to Lower Tertiary and probably older sediments have been deposited. In the Nuussuaq area these sediments are overlain by a succession of Early Tertiary basaltic volcanic rocks which reaches a combined thickness of around 2-2.5 km. Although the reservoir properties of the sandstone intervals in the GANT-1 and GANE-1 wells are generally relatively poor, it is suggested that moderate to good properties may be found in certain intervals within the Maastrichtian-Paleocene succession. However, the reason for the locally enhanced reservoir properties in GANT-1 was not clarified by this study due to the lack of regional petrographical data. (EG) EFP-96. 41 refs., 3 maps

Porosity, permeability, and their relationship in granite, basalt, and tuff

International Nuclear Information System (INIS)

1983-04-01

This report discusses the porosity, storage, and permeability of fractured (mainly crystalline) rock types proposed as host rock for nuclear waste repositories. The emphasis is on the inter-relationships of these properties, but a number of reported measurements are included as well. The porosity of rock is shown to consist of fracture porosity and matrix porosity; techniques are described for determining the total interconnected porosity through both laboratory and field measurement. Permeability coefficient, as obtained by experiments ranging from laboratory to crustal scale, is discussed. Finally, the problem of determining the relationship between porosity and permeability is discussed. There is no simple, all encompassing relationship that describes the dependence of permeability upon porosity. However, two particular cases have been successfully analyzed: flow through a single rough fracture, and flow through isotropic porous rock. These two cases are discussed in this report

Interlaboratory comparison of the measurement of retention curves

DEFF Research Database (Denmark)

Hansen, M. H.; Houvenaghel, G.; Janz, M.

1999-01-01

The results of an interlaboratory comparison of the measurement of apparent density, solid density, open porosity and retention curves are presented. Baumberger sandstone and Sander sandstone were used as test materials.Repeatability standard deviation and reproducibility standard deviation...

Porosity effects in flame length of the porous burners

Directory of Open Access Journals (Sweden)

Fatemeh Bahadori

2014-10-01

Full Text Available Furnaces are the devices for providing heat to the industrial systems like boilers, gas turbines and etc. The main challenge of furnaces is emission of huge air pollutants. However, porous burners produce less contaminant compared to others. The quality of the combustion process in the porous burners depends on the length of flame in the porous medium. In this paper, the computational fluid dynamic (CFD is used to investigate the porosity effects on the flame length of the combustion process in porous burner. The simulation results demonstrate that increasing the porosity increases the flame length and the combustion zone extends forward. So, combustion quality increases and production of carbon monoxide decrease. It is possible to conclude that temperature distribution in low porosity burner is lower and more uniform than high porosity one. Therefore, by increasing the porosity of the burner, the production of nitrogen oxides increases. So, using an intermediate porosity in the burner appears to be reasonable.

Determining optimum aging time using novel core flooding equipment

DEFF Research Database (Denmark)

Ahkami, Mehrdad; Chakravarty, Krishna Hara; Xiarchos, Ioannis

2016-01-01

the optimum aging time regardless of variations in crude oil, rock, and brine properties. State of the art core flooding equipment has been developed that can be used for consistently determining the resistivity of the coreplug during aging and waterflooding using advanced data acquisition software......New methods for enhanced oil recovery are typically developed using core flooding techniques. Establishing reservoir conditions is essential before the experimental campaign commences. The realistic oil-rock wettability can be obtained through optimum aging of the core. Aging time is affected....... In the proposed equipment, independent axial and sleeve pressure can be applied to mimic stresses at reservoir conditions. 10 coreplugs (four sandstones and six chalk samples) from the North Sea have been aged for more than 408 days in total and more than 29000 resistivity data points have been measured...

A modified Wyllie equation for the relationship between porosity and sonic velocity of mixed sediments and carbonates from the Caribbean Sea

DEFF Research Database (Denmark)

Lind, Ida

1997-01-01

Continuous drill cores from the Caribbean Sea of up to 1 km thick mixed sediments and carbonates were recovered by Ocean Drilling Program Leg 165. The sediments range in porosity from 10% to 80% and in carbonate content from 20% to 95%. Unconfined P-wave velocities from this material were measured...

Desert and groundwater dynamics of the Jurassic Navajo Sandstone, southeast Utah

Science.gov (United States)

Chan, M. A.; Hasiotis, S. T.; Parrish, J. T.

2017-12-01

The Jurassic Navajo Sandstone of southeastern Utah is a rich archive of a desert complex with an active groundwater system, influenced by climate changes and recharge from the Uncompahgre Uplift of the Ancestral Rocky Mountains. This eastern erg margin was dominated by dune deposits of large (>10 m thick) and small (m-scale) crossbedded sandstone sets. Within these porous deposits, common soft sediment deformation is expressed as contorted and upturned bedding, fluid escape structures, concentrations of clastic pipes with ring faults, and thick intervals of massive sandstone embedded in crossbedded sandstone. Collectively, these deformation features reflect changes and/or overpressure in the groundwater system. Interdune deposits record laterally variable bounding surfaces, resulting from the change in position of and proximity to the water table. Interdune modification by pedogenesis from burrows, roots, and trees suggest stable periods of moisture and water supply, as well as periodic drying expressed as polygonal cracked mud- to sand-cracked layers. Freshwater bedded and platy limestone beds represent lakes of decameter to kilometer extent, common in the upper part of the formation. Some carbonate springs that fed the lakes are preserved as limestone buildups (tufa mounds) with microbial structures. Extradunal deposits of rivers to small ephemeral streams show channelized and lenticular, subhorizontal, cm- to m-scale sandstone bodies with basal scours and rip-up clasts. Proxy records of the active hydrology imply a changing landscape at the Navajo desert's edge, punctuated by periods of significant rainfall, runoff, rivers, lakes, and springs, fed by high water table conditions to sustain periods of flourishing communities of plants, arthropods, reptiles, mammals, and dinosaurs. Strong ground motion perturbations periodically disrupted porous, water-saturated sands with possible surface eruptions, adding to the dynamic activity of the desert regime.

Application status and vistas of sequence stratigraphy to the exploration of sandstone-hosted uranium deposits

International Nuclear Information System (INIS)

Guo Qingyin; Chen Zuyi; Yu Jinshui; Han Shuqin

2008-01-01

Sequence stratigraphy is a newly developed subject based on seismostratigraphy, and has been widely applied in the exploration of hydrocarbon and other sedimentogenic mineral deposits and great achievements have been obtained. However, the application of sequence stratigraphy to the exploration of sandstone-hosted uranium deposits is just at the beginning. In this paper, some primary research achievements of sequence stratigraphy to the exploration of sandstone-hosted uranium deposits are summarized, and problems and their reasons of the application of sequence stratigraphy are discussed. Further more, according to characteristics of sandstone-hosted uranium deposits and the development of sequence stratigraphy, the application vistas of sequence stratigraphy to the exploration of sandstone-hosted uranium deposits are estimated. Finally, application directions are proposed, and some specific suggestions are given. (authors)

Pulsed neutron porosity logging system

International Nuclear Information System (INIS)

Smith, H.D. Jr.; Smith, M.P.; Schultz, W.E.

1978-01-01

An improved pulsed neutron porosity logging system is provided in the present invention. A logging tool provided with a 14 MeV pulsed neutron source, an epithermal neutron detector, and a fast neutron detector is moved through a borehole. Repetitive bursts of neutrons irradiate the earth formations and, during the bursts, the fast neutron population is sampled. During the interval between bursts the epithermal neutron population is sampled along with background gamma radiation due to lingering thermal neutrons. The fast and epithermal neutron population measurements are combined to provide a measurement of formation porosity

Insights into fluid flow and environmental conditions present in deep-sea hydrothermal vent deposits from measurements of permeability and porosity

Science.gov (United States)

Gribbin, J. L.; Zhu, W.; Tivey, M. K.

2008-12-01

Evolution of permeability-porosity relationships (EPPRs) of different seafloor vent deposit sample types provide crucial information about how fluid flows within the deposits. In this study, we conducted permeability and porosity measurements on a wide range of vent sample types recovered from many different active seafloor vent fields. The sample set includes chalcopyrite-lined black smoker chimneys, Zn-rich diffusing spires (including white smokers), flanges/slabs/crusts (i.e., plate-like deposits that overlie pooled fluid), massive anhydrite, and cores recovered from the sides of vent structures. Using a probe permeameter, permeability measurements were systematically taken of each sample along several orientations. The measured permeability ranges over 6 orders of magnitude from 10-14 to 10-8 m2. Our data indicate that in general massive anhydrite samples are the least permeable with a mean at ~10-13 m2 and the samples from Zn-rich diffusing spires that were actively venting when collected are the most permeable with a mean at ~10-11 m2. With a mean at 10-11.5 m2, permeability data of flanges/slabs/crusts span over 4 orders of magnitude from 10-13 to 10-9 m2, the largest spread among all sample types tested. Permeability values of the outer portions of relict spires, ranging from ~10-13 m2 to 10-9.5 m2, displayed clear anisotropic trends: permeability along the radial directions is higher than that along the axial direction. Black smokers exhibit a strong layered heterogeneity, where inner chalcopyrite linings were significantly less permeable than outermost layers. To conduct porosity and directional permeability measurements, cylindrical cores will be taken from these vent samples. We will examine whether different sample types, or portions of samples, exhibit distinct permeability-porosity relationships, and will then use micro-structural observations of the cores to examine chimney growth processes (e.g., mineral deposition or cracking) that likely result

Effects of Heating Rate on the Dynamic Tensile Mechanical Properties of Coal Sandstone during Thermal Treatment

Directory of Open Access Journals (Sweden)

Ming Li

2017-01-01

Full Text Available The effects of coal layered combustion and the heat injection rate on adjacent rock were examined in the process of underground coal gasification and coal-bed methane mining. Dynamic Brazilian disk tests were conducted on coal sandstone at 800°C and slow cooling from different heating rates by means of a Split Hopkinson Pressure Bar (SHPB test system. It was discovered that thermal conditions had significant effects on the physical and mechanical properties of the sandstone including longitudinal wave velocity, density, and dynamic linear tensile strength; as the heating rates increased, the thermal expansion of the sandstone was enhanced and the damage degree increased. Compared with sandstone at ambient temperature, the fracture process of heat-treated sandstone was more complicated. After thermal treatment, the specimen had a large crack in the center and cracks on both sides caused by loading; the original cracks grew and mineral particle cracks, internal pore geometry, and other defects gradually appeared. With increasing heating rates, the microscopic fracture mode transformed from ductile fracture to subbrittle fracture. It was concluded that changes in the macroscopic mechanical properties of the sandstone were result from changes in the composition and microstructure.

Geotechnical properties of two siliceous cores from the central Indian Ocean

Digital Repository Service at National Institute of Oceanography (India)

Khadge, N.H.

Physical properties of the siliceous sediments from the Central Indian Basin are measured on two short cores. The properties such as water content, Atterberg limits, porosity specific gravity, wet density show the medium to high plastic sediment...

Quantitative mineralogical analysis of sandstones using x-ray diffraction techniques

International Nuclear Information System (INIS)

Ward, C.R.; Taylor, J.C.

1999-01-01

Full text: X-ray diffraction has long been used as a definitive technique for mineral identification based on the measuring the internal atomic or crystal structures present in powdered rocks; soils and other mineral mixtures. Recent developments in data gathering and processing, however, have provided an improved basis for its use as a quantitative tool, determining not only the nature of the minerals but also the relative proportions of the different minerals present. The mineralogy of a series of sandstone samples from the Sydney and Bowen Basins of eastern Australia has been evaluated by X-ray diffraction (XRD) on a quantitative basis using the Australian-developed SIROQUANT data processing technique. Based on Rietveld principles, this technique generates a synthetic X-ray diffractogram by adjusting and combining full-profile patterns of minerals nominated as being present in the sample and interactively matches the synthetic diffractogram under operator instructions to the observed diffractogram of the sample being analysed. The individual mineral patterns may be refined in the process, to allow for variations in crystal structure of individual components or for factors such as preferred orientation in the sample mount. The resulting output provides mass percentages of the different minerals in the mixture, and an estimate of the error associated with each individual percentage determination. The chemical composition of the mineral mixtures indicated by SIROQUANT for each individual sandstone studied was estimated using a spreadsheet routine, and the indicated proportion of each oxide in each sample compared to the actual chemical analysis of the same sandstone as determined independently by X-ray fluorescence spectrometry. The results show a high level of agreement for all major chemical constituents, indicating consistency between the SIROQUANT XRD data and the whole-rock chemical composition. Supplementary testing with a synthetic corundum spike further

Plant fibre composites - porosity and stiffness

DEFF Research Database (Denmark)

Madsen, Bo; Thygesen, Anders; Lilholt, Hans

2009-01-01

Plant fibre composites contain typically a relatively large amount of porosity which influences their performance. A model, based on a modified rule of mixtures, is presented to include the influence of porosity on the composite stiffness. The model integrates the volumetric composition...... of the composites with their mechanical properties. The fibre weight fraction is used as an independent parameter to calculate the complete volumetric composition. A maximum obtainable stiffness of the composites is calculated at a certain transition fibre weight fraction, which is characterised by a best possible...... combination of high fibre volume fraction and low porosity. The model is validated with experimental data from the literature on several types of composites. A stiffness diagram is presented to demonstrate that the calculations can be used for tailoring and design of composites with a given profile...

Current status and prospects of uranium geology developments of foreign in-situ leachable sandstone type uranium deposits

International Nuclear Information System (INIS)

Wang Zhengbang

2002-01-01

Firstly, with emphasis on in-situ leachable sandstone-type uranium deposits, the prospecting history of uranium deposits worldwide and its scientific research development are generally reviewed in four steps, and their basic historical experience is also summarized. Secondly, based on the detailed description of current development status of uranium geology of foreign in-situ leachable sandstone-type uranium deposits the important strategic position of sandstone-type uranium deposits in overall uranium resources all-over-the-world and its classification, spatial-temporal distribution and regulation, and metallogenic condition of sandstone-type uranium deposits are analysed thoroughly in five aspects: techtonics, paleo-climate, hydrogeology, sedimentary facies and lithology, as well as uranium sources: Afterwards, evaluation principles of three type of hyper-genic, epigenetic infiltrated sandstone-type uranium deposits are summarized. Based on sandstone-type uranium deposits located two important countries: the United States and Russia, the current development status of prospecting technology for in-situ leachable sandstone-type uranium deposits in foreign countries is outlined. Finally, according to the prospects of supply-demand development of global uranium resources, the author points out seriously that Chinese uranium geology is faced with a severe challenge, and proposes directly four strategic measures that should be taken

Geotechnical Assessment of United States and Foreign Test Sites and Material Properties of Geologic Media

Science.gov (United States)

1979-06-01

34Granite" Westerly granite (Rhode Island) Climax Stock granodiorite (Nevada Test Site) Sandstone Kayenta formation (Mixed Comany site, Colorado) Nugget...Grain size ranges between .1 to 1.3 -. Porosity is low for a sandstone, approximately 4 percent. Kayenta Forwfation Kayeata Formation is a fine to...Comparison of the fail envelopespfos fshale, sandstone a granite.aluim g19 NARDLAT SRANOjoniOrTe ) ’U SW UGET SANS (H) . KAYENTA SANDSTONE (S) S 02 --.-: j W

Characterizing gas shaly sandstone reservoirs using the magnetic resonance technology in the Anaco area, East Venezuela

Energy Technology Data Exchange (ETDEWEB)

Fam, Maged; August, Howard [Halliburton, Houston, TX (United States); Zambrano, Carlos; Rivero, Fidel [PDVSA Gas (Venezuela)

2008-07-01

With demand for natural gas on the rise every day, accounting for and booking every cubic foot of gas is becoming very important to operators exploiting natural gas reservoirs. The initial estimates of gas reserves are usually established through the use of petrophysical parameters normally based on wireline and/or LWD logs. Conventional logs, such as gamma ray, density, neutron, resistivity and sonic, are traditionally used to calculate these parameters. Sometimes, however, the use of such conventional logs may not be enough to provide a high degree of accuracy in determining these petrophysical parameters, which are critical to reserve estimates. Insufficient accuracy can be due to high complexities in the rock properties and/or a formation fluid distribution within the reservoir layers that is very difficult to characterize with conventional logs alone. The high degree of heterogeneity in the shaly sandstone rock properties of the Anaco area, East Venezuela, can be characterized by clean, high porosity, high permeability sands to very shaly, highly laminated, and low porosity rock. This wide variation in the reservoir properties may pose difficulties in identifying gas bearing zones which may affect the final gas reserves estimates in the area. The application of the magnetic resonance imaging (MRI) logging technology in the area, combined with the application of its latest acquisition and interpretation methods, has proven to be very adequate in detecting and quantifying gas zones as well as providing more realistic petrophysical parameters for better reserve estimates. This article demonstrates the effectiveness of applying the MRI logging technology to obtain improved petrophysical parameters that will help better characterize the shaly-sands of Anaco area gas reservoirs. This article also demonstrates the value of MRI in determining fluid types, including distinguishing between bound water and free water, as well as differentiating between gas and liquid

Nodular features from Proterozoic Sonia Sandstone, Jodhpur Group ...

Indian Academy of Sciences (India)

Corresponding author. e-mail: parthageology@gmail.com. The Sonia ..... cement variety in the form of dispersed dark brown clots and .... content within the nodule sandstones bear sig- nature in ..... Carbonates and Evaporites 21 133–143.

Geohydrology of the Navajo sandstone in western Kane, southwestern Garfield, and southeastern Iron counties, Utah

Science.gov (United States)

Freethey, G.W.

1988-01-01

The upper Navajo and Lamb Point aquifers in the Navajo Sandstone are the principal source of water for the city of Kanab, irrigation, stock, and for rural homes in the study area. Well logs and outcrop descriptions indicate the Navajo Sandstone consists of the Lamb Point Tongue and an unnamed upper member that are separated by the Tenney Canyon Tongue of the Kayenta Formation. The main Kayenta Formation underlies the Lamb Point Tongue. The Lamb Point Tongue and the upper member of the Navajo Sandstone are saturated and hydraulically connected through the Tenney Canyon Tongue. Available data indicate that precipitation percolates to the groundwater reservoir where the Navajo Sandstone crops out. Estimates of the rate of recharge at the outcrop range from 0.1 to as much as 2.8 in/yr. Water level data indicate that water moves from the upper member of the Navajo Sandstone, through the Tenney Canyon Tongue, and into the Lamb Point Tongue. Lateral flow is generally from the outcrop areas toward the incised canyons formed by tributaries of Kanab Creek and Johnson Wash. Direction and rate of groundwater movement and the location and character of the natural hydrologic boundaries in the northern part of the area where the Navajo Sandstone is buried cannot be determined conclusively without additional water level data. (Author 's abstract)

A New Multichelating Acid System for High-Temperature Sandstone Reservoirs

Directory of Open Access Journals (Sweden)

Nianyin Li

2015-01-01

Full Text Available Sandstone reservoir acidizing is a complex and heterogeneous acid-rock reaction process. If improper acid treatment is implemented, further damage can be induced instead of removing the initial plug, particularly in high-temperature sandstone reservoirs. An efficient acid system is the key to successful acid treatment. High-temperature sandstone treatment with conventional mud acid system faces problems including high acid-rock reaction rate, short acid effective distance, susceptibility to secondary damage, and serious corrosion to pipelines. In this paper, a new multichelating acid system has been developed to overcome these shortcomings. The acid system is composed of ternary weak acid, organic phosphonic chelating agent, anionic polycarboxylic acid chelating dispersant, fluoride, and other assisted additives. Hydrogen ion slowly released by multistage ionization in ternary weak acid and organic phosphonic within the system decreases the concentration of HF to achieve retardation. Chelating agent and chelating dispersant within the system inhibited anodic and cathodic reaction, respectively, to protect the metal from corrosion, while chelating dispersant has great chelating ability on iron ions, restricting the depolarization reaction of ferric ion and metal. The synergic effect of chelating agent and chelating dispersant removes sulfate scale precipitation and inhibits or decreases potential precipitation such as CaF2, silica gel, and fluosilicate. Mechanisms of retardation, corrosion-inhibition, and scale-removing features have been discussed and evaluated with laboratory tests. Test results indicate that this novel acid system has good overall performance, addressing the technical problems and improving the acidizing effect as well for high-temperature sandstone.

Research on geochronology and uranium source of sandstone-hosted uranium ore-formation in major uranium-productive basins, Northern-China

International Nuclear Information System (INIS)

Xia Yuliang; Liu Hanbin; Lin Jinrong; Fan Guang; Hou Yanxian

2004-12-01

A method is developed for correcting uranium content in uranium ore samples by considering the U-Ra equilibrium coefficient, then a U-Pb isochron is drawn up. By performing the above correction ore-formation ages of sandstone-hosted uranium mineralization which may be more realistic have been obtained. The comparative research on U-Pb isotopic ages of detritic zircon in ore-hosting sandstone and zircon in intermediate-acid igneous rocks in corresponding provenance area indicates that the ore-hosting sandstone is originated from the erosion of intermediate-acid igneous rocks and the latters are the material basis for the formation of the uranium-rich sandstone beds. On the basis of the study on U-Pb isotopic system evolution of the provenance rocks and sandstones from ore-hosting series, it is verified that the uranium sources of the sandstone-hosted uranium deposit are: the intermediate-acid igneous rocks with high content of mobile uranium, and the sandstone bodies pre-concentrated uranium. (authors)

Fabrication of dual porosity electrode structure

Science.gov (United States)

Smith, J.L.; Kucera, E.H.

1991-02-12

A substantially entirely fibrous ceramic is described which may have dual porosity of both micro and macro pores. Total porosity may be 60-75% by volume. A method of spraying a slurry perpendicularly to an ambient stream of air is disclosed along with a method of removing binders without altering the fiber morphology. Adding fine ceramic particulates to the green ceramic fibers enhances the sintering characteristics of the fibers. 3 figures.

Study on U-Ra equilibrium coefficient of the in-situ leaching sandstone-type uranium deposits: A case study of Qianjiadian uranium deposit

International Nuclear Information System (INIS)

Xia Yuliang; Xiu Qunye; Han Jun; Li Linqiang; Zheng Jiwei

2013-01-01

This paper investigated the U-Ra equilibrium coefficient (K-p) of mineralized sandstone and mudstone, and unmineralized sandstone and mudstone for the in-situ leaching sandstone-type uranium deposits. It is surprised that all of the mineralized sandstone and mudstone are both relatively to be partial to uranium, but all of the unmineralized sandstone and mudstone are both relatively to be partial to radium. Meanwhile the uranium in mineralized mudstone is relatively richer than that in mineralized sandstone, and the radium in unmineralized mudstone is relatively richer than that in unmineralized sandstone. It is suggested that mudstones were permeable at the uranium mineralized phase and the unmineralized mudstone and sandstone could serve as important mineralized uranium source. (authors)

Generating porosity spectrum of carbonate reservoirs using ultrasonic imaging log

Science.gov (United States)

Zhang, Jie; Nie, Xin; Xiao, Suyun; Zhang, Chong; Zhang, Chaomo; Zhang, Zhansong

2018-03-01

Imaging logging tools can provide us the borehole wall image. The micro-resistivity imaging logging has been used to obtain borehole porosity spectrum. However, the resistivity imaging logging cannot cover the whole borehole wall. In this paper, we propose a method to calculate the porosity spectrum using ultrasonic imaging logging data. Based on the amplitude attenuation equation, we analyze the factors affecting the propagation of wave in drilling fluid and formation and based on the bulk-volume rock model, Wyllie equation and Raymer equation, we establish various conversion models between the reflection coefficient β and porosity ϕ. Then we use the ultrasonic imaging logging and conventional wireline logging data to calculate the near-borehole formation porosity distribution spectrum. The porosity spectrum result obtained from ultrasonic imaging data is compared with the one from the micro-resistivity imaging data, and they turn out to be similar, but with discrepancy, which is caused by the borehole coverage and data input difference. We separate the porosity types by performing threshold value segmentation and generate porosity-depth distribution curves by counting with equal depth spacing on the porosity image. The practice result is good and reveals the efficiency of our method.

Casting Porosity-Free Grain Refined Magnesium Alloys

Energy Technology Data Exchange (ETDEWEB)

Schwam, David [Case Western Reserve University

2013-08-12

The objective of this project was to identify the root causes for micro-porosity in magnesium alloy castings and recommend remedies that can be implemented in production. The findings confirm the key role played by utilizing optimal gating and risering practices in minimizing porosity in magnesium castings. 

Carbonate porosity: some remarks; Porosidade em reservatorios carbonaticos: algumas consideracoes

Energy Technology Data Exchange (ETDEWEB)

Spadini, Adali Ricardo [PETROBRAS, Rio de Janeiro, RJ (Brazil). Exploracao e Producao]. E-mail: spadini@petrobras.com.br; Marcal, Rosely de Araujo [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2005-05-01

Carbonate rocks are the major reservoirs of the largest super-giants fields in the world, including the Ghawar Field in Saudi Arabia, where the producing oil reservoir is the late Jurassic Arab-D limestone with five million barrels per day. Despite the great susceptibility to early diagenesis, that can dramatically modify the porous media, porosity values of carbonates remain essentially the same as that of deposition before burial. Porosity loss is essentially a subsurface process with a drastic reduction below 2500 m of burial depth. The occurrence of good reservoirs deeply buried, sometimes below 4,000 m, indicate that porosity can be preserved in subsurface in response to a series of mechanisms such as early oil emplacement, framework rigidity, abnormal pore pressure, among others. Percolation of geothermal fluids is a process considered to be responsible for generation of porosity in subsurface resulting in some good reservoir rocks. In Campos Basin, areas with burial around 2000 m, petrophysical data show a cyclic distribution that coincides with the shoaling upward cycles typical of the Albian carbonates. The greatest permeabilities coincide with the grain stones of the top of the cycles while the peloidal/oncolite wackestones/pack stones at the base show low values, reflecting the depositional texture. These relationships indicate that preservation of depositional porosity was very effective. The preservation of high porosity values for all the facies are related to early oil entrance in the reservoirs. In some cases, the presence of porosities of almost 30% in fine-grained peloidal carbonates, 3000 m of burial, without any clear effective preservation mechanism, suggest that corrosive subsurface brines have played an important role in porosity evolution. In Santos Basin, where reservoirs are deeply buried, only the grain stones have preserved porosity. The associated low energy facies has virtually no porosity. In this case, the depositional texture

Porosity evolution in Icelandic hydrothermal systems

Science.gov (United States)

Thien, B.; Kosakowski, G.; Kulik, D. A.

2014-12-01

Mineralogical alteration of reservoir rocks, driven by fluid circulation in natural or enhanced hydrothermal systems, is likely to influence the long-term performance of geothermal power generation. A key factor is the change of porosity due to dissolution of primary minerals and precipitation of secondary phases. Porosity changes will affect fluid circulation and solute transport, which, in turn, influence mineralogical alteration. This study is part of the Sinergia COTHERM project (COmbined hydrological, geochemical and geophysical modeling of geotTHERMal systems, grant number CRSII2_141843/1) that is an integrative research project aimed at improving our understanding of the sub-surface processes in magmatically-driven natural geothermal systems. These are typically high enthalphy systems where a magmatic pluton is located at a few kilometers depth. These shallow plutons increase the geothermal gradient and trigger the circulation of hydrothermal waters with a steam cap forming at shallow depth. Field observations suggest that active and fossil Icelandic hydrothermal systems are built from a superposition of completely altered and completely unaltered layers. With help of 1D and 2D reactive transport models (OpenGeoSys-GEM code), we investigate the reasons for this finding, by studying the mineralogical evolution of protoliths with different initial porosities at different temperatures and pressures, different leaching water composition and gas content, and different porosity geometries (i.e. porous medium versus fractured medium). From this study, we believe that the initial porosity of protoliths and volume changes due to their transformation into secondary minerals are key factors to explain the different alteration extents observed in field studies. We also discuss how precipitation and dissolution kinetics can influence the alteration time scales.

Effect of shrinkage porosity on mechanical properties of ferritic ductile iron

Directory of Open Access Journals (Sweden)

Wang Zehua

2013-05-01

Full Text Available Casting defects could largely affect the mechanical properties of casting products. A number of test pieces made of ductile iron (EN-GJS-400-18-LT with different levels of shrinkage porosity were prepared and then tensile and fatigue tests were performed to investigate the impact of shrinkage porosity on their mechanical properties. The results showed that the tensile strength decreases linearly with increasing of the shrinkage porosity. The tensile elongation decreases sharply with the increase of the shrinkage porosity mainly due to the non-uniform plastic deformation. The fatigue life also dramatically declines with increasing of the porosity and follows a power law relationship with the area percentage of porosity. The existence of the shrinkage porosity made the fatigue fracture complex. The shrinkage pores, especially those close to the surface usually became the crack initiation sites. For test pieces with less porosity, the fatigue fracture was clearly composed of crack initiation, propagation, and overloading. While for samples with high level of porosity, multiple crack initiation sites were observed.

Imaging techniques applied to the study of fluids in porous media

Energy Technology Data Exchange (ETDEWEB)

Tomutsa, L.; Doughty, D.; Mahmood, S.; Brinkmeyer, A.; Madden, M.P.

1991-01-01

A detailed understanding of rock structure and its influence on fluid entrapment, storage capacity, and flow behavior can improve the effective utilization and design of methods to increase the recovery of oil and gas from petroleum reservoirs. The dynamics of fluid flow and trapping phenomena in porous media was investigated. Miscible and immiscible displacement experiments in heterogeneous Berea and Shannon sandstone samples were monitored using X-ray computed tomography (CT scanning) to determine the effect of heterogeneities on fluid flow and trapping. The statistical analysis of pore and pore throat sizes in thin sections cut from these sandstone samples enabled the delineation of small-scale spatial distributions of porosity and permeability. Multiphase displacement experiments were conducted with micromodels constructed using thin slabs of the sandstones. The combination of the CT scanning, thin section, and micromodel techniques enables the investigation of how variations in pore characteristics influence fluid front advancement, fluid distributions, and fluid trapping. Plugs cut from the sandstone samples were investigated using high resolution nuclear magnetic resonance imaging permitting the visualization of oil, water or both within individual pores. The application of these insights will aid in the proper interpretation of relative permeability, capillary pressure, and electrical resistivity data obtained from whole core studies. 7 refs., 14 figs., 2 tabs.

Integrated prediction based on GIS for sandstone-type uranium deposits in the northwest of Ordos Basin

International Nuclear Information System (INIS)

Han Shaoyang; Ke Dan; Hu Shuiqing; Guo Qingyin; Hou Huiqun

2005-01-01

The integrated prediction model of sandstone-type uranium deposits and its integrated evaluation methods as well as flow of the work based on GIS are studied. A software for extracting metallogenic information is also developed. A multi-source exploring information database is established in the northwest of Ordos Basin, and an integrated digital mineral deposit prospecting model of sandstone-type uranium deposits is designed based on GIS. The authors have completed metallogenic information extraction and integrated evaluation of sandstone-type uranium deposits based on GIS in the study area. Research results prove that the integrated prediction of sandstone-type uranium deposits based on GIS may further delineate prospective target areas rapidly and improve the predictive precision. (authors)

Structural and microstructural evolution of fault zones in Cretaceous poorly lithified sandstones of the Rio do Peixe basin, Paraiba, NE Brazil

Science.gov (United States)

Balsamo, Fabrizio; Nogueira, Francisco; Storti, Fabrizio; Bezerra, Francisco H. R.; De Carvalho, Bruno R.; André De Souza, Jorge

2017-04-01

In this contribution we describe the structural architecture and microstructural features of fault zones developed in Cretaceous, poorly lithified sandstones of the Rio do Peixe basin, NE Brazil. The Rio do Peixe basin is an E-W-trending, intracontinental half-graben basin developed along the Precambrian Patos shear zone where it is abutted by the Porto Alegre shear zone. The basin formed during rifting between South America and Africa plates and was reactivated and inverted in a strike-slip setting during the Cenozoic. Sediments filling the basin consist of an heterolithic sequence of alternating sandstones, conglomerates, siltstone and clay-rich layers. These lithologies are generally poorly lithified far from the major fault zones. Deformational structures in the basin mostly consist of deformation band-dominated fault zones. Extensional and strike-slip fault zones, clusters of deformation bands, and single deformation bands are commonly well developed in the proximity of the basin-boundary fault systems. All deformation structures are generally in positive relief with respect to the host rocks. Extensional fault zones locally have growth strata in their hangingwall blocks and have displacement generally <10 m. In map view, they are organized in anastomosed segments with high connectivity. They strike E-W to NE-SW, and typically consist of wide fault cores (< 1 m in width) surrounded by up to few-meter wide damage zones. Fault cores are characterized by distributed deformation without pervasive strain localization in narrow shear bands, in which bedding is transposed into foliation imparted by grain preferred orientation. Microstructural observations show negligible cataclasis and dominant non-destructive particulate flow, suggesting that extensional fault zones developed in soft-sediment conditions in a water-saturated environment. Strike-slip fault zones commonly overprint the extensional ones and have displacement values typically lower than about 2 m. They

Characterization of glass filter micromodels used for polymer EOR flooding experiments

Energy Technology Data Exchange (ETDEWEB)

Foedisch, H.; Wegner, J.; Hincapie-Reina, R.; Ganzer, L. [Technische Univ. Clausthal, Clausthal-Zellerfeld (Germany). ITE

2013-08-01

This work is conducted as part of the research project DGMK 746 - ''Experimental and Numerical Analysis of Polymer Flooding Processes Using Micromodels - From Pore Scale to Continuum Scale''. The industry standard to assess polymer flood performance is through flooding experiments with cores or plugs. A complement to flooding experiments in cores is represented by micromodels such as glass filters, which resemble real porous media through their porous structures. In this way, an almost unlimited number of equivalent samples can be produced. Moreover, compared to cores the micromodels enable visual access to the flooding process enabling a detailed process description. The sintered glass filters used in this work represent one way to make displacement processes inside artificial structures visible. However, challenges exist to transfer the results obtained from models composed of glass to real plugs or rock sections. Therefore, this study focuses on the comparison of glass filter micromodels and real rock samples composed of Bentheimer sandstone. We determine water permeability and oil-water relative permeability endpoints with flooding experiments, compare capillary pressure functions of the glass models obtained from mercury porosimetry analysis with results from Bentheimer sandstone, and characterize the glass filter with respect of connate water saturation using NMR-spectroscopy and porosity obtained from pycnometer measurements. (orig.)

Application research on remote sensing geology of sandstone-type uranium deposit in Yili basin

International Nuclear Information System (INIS)

Wang Huaiwu

2002-01-01

Based on remote sensing images and practical materials, and new ideas of laying particular emphasis on the research of regional geologic structures, and large in-situ leachable sandstone-type uranium deposits, applying the theory of plate tectonics, the author makes a comprehensive analysis on the uranium metallogenic environments, characteristics of regional geologic structures, the ore-controlling mechanism and factors, and uranium metallogeny. Authors propose that large interlayer oxidation zone sandstone-type uranium deposits are controlled by the combination of the stable block in Meso-Cenozoic compressive-shearing faulted subsided basin on the Yili multiphase massif in Tianshan paleo-island arc system, and the specific paleo-geographic environments and its' structural terrace'. The origin of hydrogenic sandstone-type uranium deposits is summarized by the authors as the 'mixing and neutralization' genetic model, and the 'eight ore-controlling factors merge into an organic whole' prospecting model. The above mentioned provides clear prospecting direction and new ideas for the forecasting direction for prospecting large sandstone-type uranium deposits

Study on integrated evaluation of sandstone-hosted uranium metallogenic potential in southern Yili basin

International Nuclear Information System (INIS)

Han Shaoyang; Ke Dan; Xu Jianguo; Zheng Enjiu; Li Shengxiang

2008-01-01

Plenty of geological data have been accumulated during mineral resource survey in China; under the guidance of new metallogenic theories, it is an important task of how to use these data most effectively for the new cycle uranium survey. In this paper, the flow of establishing the integrated mineral deposits prospecting model for sandstone-hosted uranium deposits is put forward. Based on studying geologic, hydrogeologic and regional geophysical field characteristics of representative uranium deposits No. 512 in southern Yili basin, its multi-source information descriptive model has been established, from which 512-type integrated prospecting models of sandstone-hosted uranium orefield and deposits are summarized. According to the established integrated prospecting models, the metallogenic information extraction of sandstone-hosted uranium deposits has completed in the study area. Finally, the integrated quantitative evaluation of sandstone-hosted uranium metallogenic potential is performed by using the evidence weighing method to integrate middle scale multi-source metallogenic information in the southern Yili basin, and good prediction effect is obtained. (authors)

Experimental and Numerical Investigations on Strength and Deformation Behavior of Cataclastic Sandstone

Science.gov (United States)

Zhang, Y.; Shao, J. F.; Xu, W. Y.; Zhao, H. B.; Wang, W.

2015-05-01

This work is devoted to characterization of the deformation and strength properties of cataclastic sandstones. Before conducting mechanical tests, the physical properties were first examined. These sandstones are characterized by a loose damaged microstructure and poorly cemented contacts. Then, a series of mechanical tests including hydrostatic, uniaxial, and triaxial compression tests were performed to study the mechanical strength and deformation of the sandstones. The results obtained show nonlinear stress-strain responses. The initial microcracks are closed at hydrostatic stress of 2.6 MPa, and the uniaxial compressive strength is about 0.98 MPa. Under triaxial compression, there is a clear transition from volumetric compressibility to dilatancy and a strong dependency on confining pressure. Based on the experimental evidence, an elastoplastic model is proposed using a linear yield function and a nonassociated plastic potential. There is good agreement between numerical results and experimental data.

The controlling role of positive structures over the metallogenesis and emplacement of inter layer oxidation sandstone type uranium deposits

International Nuclear Information System (INIS)

Gu Kangheng; Chen Zuyi

2010-01-01

The positive structures in this paper mean the geological structures related to the occurrence of U-metallogenic zones or U-deposit such as anticlines, uplifts and uplifted fault-blocks. Occurrence features of interlayer oxidation sandstone type deposit at the southern margin of Yili basin and southwestern margin of Turpan-Hami basin, the northeastern margin of Jiudong basin illustrate that the sandstone-hosted uranium deposits, the U-mineralized sections and the uranium occurrences are always selectively emplaced on/in positive structures. The reasons for this lie in the formation mechanism of sandstone-hosted U-deposits. The positive structures raised the elevation of ore-hosting sandstone horizon and make it close to ground surface or exposed at the ground surface, which result in the infiltration of uranium and oxygen bearing groundwater from recharge area into host sandstone horizon, and the interlayer oxidation of host sandstone, as well as the dissolution and the migration of uranium in host sandstone, and the reduction mineralization at the oxidation-reduction interface. Sufficient attention should be paid to the controlling role of positive structures over the metallogenesis and emplacement of sandstone-hosted uranium deposits. They could act as an important criterion for recognizing and prognosticating potential uranium mineralized areas in uranium metallogenic zones or uranium-productive sedimentary basins. (authors)

The sedimentology of uranium-bearing sandstones on the farm Ryst Kuil 351 Beaufort West area

International Nuclear Information System (INIS)

Cole, D.I.

1979-06-01

A study of the sedimentology of some uranium-bearing sandstones on the farm Ryst Kuil 351 was made in order to assess possible relationships between the mineralisation and the sedimentary facies and/or the palaeo-environment. Use was made of 6 vertical profiles, derived from horizontal traverses. 12 sedimentary facies were recognised according to grain-size and sedimentary structure. The transitions between these facies, as derived from the vertical profiles, were subjected to Markov analysis. Only 3 Markov-dependent transitions were derived, but several facies transitions and associations occurred with greater than random frequency. These, together with the vertical profiles, were used to interpret the palaeo-environmental succession. This succession is fluvial meandering and two sub-environments - channel and flood plain - were delineated according to the prevalence of sandstone or mudstone facies. The uranium-bearing sandstones occur in the lower part of a thick (29 - 46m) multistorey point bar sequence within the channel sub-environment. The mineralisation is associated with koffieklip and is restricted to two sedimentary facies - massive very fine-to-finegrained sandstone and horizontally bedded, very fine- to fine-grained sandstone. The mineralisation normally occurs near the bases of the point bars

Contributions to the study of porosity in fly ash-based geopolymers. Relationship between degree of reaction, porosity and compressive strength

Directory of Open Access Journals (Sweden)

Y. Luna-Galiano

2016-09-01

Full Text Available The main contribution of this paper relates to the development of a systematic study involving a set of parameters which could potentially have an impact on geopolymer properties: curing temperature, type of activating solution, alkali metal in solution, incorporation of slag (Ca source and type of slag used. The microstructures, degrees of reaction, porosities and compressive strengths of geopolymers have been evaluated. Geopolymers prepared with soluble silicate presented a more compacted and closed structure, a larger amount of gel, lower porosity and greater compressive strength than those prepared with hydroxides. On the other hand, Na-geopolymers were more porous but more resistant than K-geopolymers. Although there is an inverse relation between degree of reaction and porosity, between compressive strength and porosity it is not always inversely proportional and could, in some cases, be masked by changes produced in other influencing parameters.

Multielement statistical evidence for uraniferous hydrothermal activity in sandstones overlying the Phoenix uranium deposit, Athabasca Basin, Canada

Science.gov (United States)

Chen, Shishi; Hattori, Keiko; Grunsky, Eric C.

2018-04-01

The Phoenix U deposit, with indicated resources of 70.2 M lb U3O8, occurs along the unconformity between the Proterozoic Athabasca Group sandstones and the crystalline basement rocks. Principal component analysis (PCA) is applied to the compositions of sandstones overlying the deposit. Among PCs, PC1 accounts for the largest variability of U and shows a positive association of U with rare earth elements (REEs) + Y + Cu + B + Na + Mg + Ni + Be. The evidence suggests that U was dispersed into sandstones together with these elements during the uraniferous hydrothermal activity. Uranium shows an inverse association with Zr, Hf, Th, Fe, and Ti. Since they are common in detrital heavy minerals, such heavy minerals are not the major host of U. The elements positively associated with U are high in concentrations above the deposit, forming a "chimney-like" or "hump-like" distribution in a vertical section. Their enrichment patterns are explained by the ascent of basement fluids through faults to sandstones and the circulation of basinal fluids around the deposit. The Pb isotope compositions of whole rocks are similar to expected values calculated from the concentrations of U, Th, and Pb except for sandstones close to the deposit. The data suggest that in situ decay of U and Th is responsible for the Pb isotope compositions of most sandstones and that highly radiogenic Pb dispersed from the deposit to the proximal sandstones long after the mineralization. This secondary dispersion is captured in PC8, which has low eigenvalue. The data suggests that the secondary dispersion has minor effect on the overall lithogeochemistry of sandstones.

Controls on the variability of net infiltration to desert sandstone

Science.gov (United States)

Heilweil, Victor M.; McKinney, Tim S.; Zhdanov, Michael S.; Watt, Dennis E.

2007-01-01

As populations grow in arid climates and desert bedrock aquifers are increasingly targeted for future development, understanding and quantifying the spatial variability of net infiltration becomes critically important for accurately inventorying water resources and mapping contamination vulnerability. This paper presents a conceptual model of net infiltration to desert sandstone and then develops an empirical equation for its spatial quantification at the watershed scale using linear least squares inversion methods for evaluating controlling parameters (independent variables) based on estimated net infiltration rates (dependent variables). Net infiltration rates used for this regression analysis were calculated from environmental tracers in boreholes and more than 3000 linear meters of vadose zone excavations in an upland basin in southwestern Utah underlain by Navajo sandstone. Soil coarseness, distance to upgradient outcrop, and topographic slope were shown to be the primary physical parameters controlling the spatial variability of net infiltration. Although the method should be transferable to other desert sandstone settings for determining the relative spatial distribution of net infiltration, further study is needed to evaluate the effects of other potential parameters such as slope aspect, outcrop parameters, and climate on absolute net infiltration rates.

INAA and petrological study of sandstones from Khmer temples in Angkor

International Nuclear Information System (INIS)

Kucera, J.; Kranda, K.; Novak, J.K.; Poncar, J.; Krausova, I.; Soukal, L.

2009-01-01

INAA was used to determine 35 major, minor and trace elements in sandstone samples taken from building blocks of 21 Khmer temples in Angkor, Cambodia. The sandstone samples were also characterized by conventional optical microscopy, X-ray diffraction analysis and electron microprobe analysis. The aim of this work was to examine the hypothesis that a particular elemental and/or mineral composition of the building materials can be characteristic of a particular architectural style/building period in the history of constructing the Angkor monuments. Preliminary results of this study are presented

Recent exploration progresses on sandstone-hosted uranium deposits in north-western China

International Nuclear Information System (INIS)

Li, Z.

2014-01-01

The metallogenic target selection using multiple exploration techniques and drilling program for sandstone-hosted uranium deposits have been intensively carried out for recent years, and big progresses on new discoveries of uranium reserve/resource have been made in the Mesozoic sedimentary basins such as in Yili, Ordos etc. in North-western China The Yili basin is a depression one within the Tianshan Mountain belt in the western part of China. Its basement is composed of Proterozoic-Paleozoic metamorphic and sedimentary rocks, and covers of Mesozoic sediments. The early-middle Jurassic Shuixigou Group is major uranium-productive beds which are composed of three Formations such as Badaowan, Sangonghe, Xisanyao and eight sedimentary cycles. Uranium deposits are found in the south margin of the Basin and controlled by the redox zone. The combined exploration techniques of detailed sedimentary facies study, Rn-survey, high-precision magnetic and soil geochemical and seismic surveys have been successfully used to have locate the potential targets and mineralization zones. The enlargement of uranium reserve/resources in the known deposits and new resources in the selected new targets and cycles have been achieved through further drilling programs. The Ordos basin is a large Meso-Cenozoic basin developed in North China Platform, with its size of approximately 250,000 km"2 and is well known as an important “energy resources basin” because of abundance of coal, oil and gas deposits. The Dongsheng sandstone type uranium deposit is a large one discovered in recent years in northeastern Ordos basin. It is a special kind of sandstone type uranium deposit, different from other ordinary sandstone type deposits because of its unique signatures. It is generally controlled by a transitional zone between greenish and grayish sandstones, both of those two kinds of sandstones now indicate reduced geochemical environments. The greenish color of the paleooxidized sandstones mainly

Relationship between micro-porosity and tensile properties of 6063 alloy

Directory of Open Access Journals (Sweden)

Li Xiehua

2013-01-01

Full Text Available The micro-porosity is usually present in the as-cast microstructure, which decreases the tensile strength and ductility and therefore limit the application of cast aluminum parts. Although much work has been done to investigate the effects of various casting parameters on the formation of porosity in various aluminum alloys, up to now, little information has been available for the relationship between micro-porosity and tensile properties of 6063 alloy. In this study, the influences of size and area fraction of micro-porosity on the tensile properties and fracture behavior of 6063 aluminum alloy were investigated by means of tensile testing, optical microscopy (OM, and scanning electron microscopy (SEM. The tensile tests were conducted in air at 100 ℃, 200 ℃ and 300 ℃, respectively. Results show that the large micro-porosity with sizes between 100 μm and 800 μm located at the center and top of the ingot, while the small micro-porosity with size between 2 μm and 60 μm distributed at the edge and bottom of the ingot. The area fraction of micro-porosity at the center of the ingot is much bigger than that at the edge of the ingot. When tested at 100 ℃, with the decrease in the area fraction of micro-porosity from the top of the ingot to the bottom of the ingot, the ultimate tensile strength, yield strength and the elongation are increased from 82 to 99 MPa, 32 to 66 MPa and 7% to 11%, respectively. When the temperature is no more than 200 ℃, the strain hardening exponent decreases with an increase in the area fraction of micro-porosity; while the deviation disappears when the temperature reaches 300 ℃. The fracture mode of the alloy is greatly influenced by the size and area fraction of the micro-porosity.

A new bee species that excavates sandstone nests

Science.gov (United States)

Many wonder why animals act in seemingly injurious ways. Understanding the behavior of pollinators such as bees is especially important because of the necessary ecosystem service they provide. The new species Anthophora pueblo, discovered excavating sandstone nests, provides a model system for addre...

Mechanical Behavior of Red Sandstone under Incremental Uniaxial Cyclical Compressive and Tensile Loading

Directory of Open Access Journals (Sweden)

Baoyun Zhao

2017-01-01

Full Text Available Uniaxial experiments were carried out on red sandstone specimens to investigate their short-term and creep mechanical behavior under incremental cyclic compressive and tensile loading. First, based on the results of short-term uniaxial incremental cyclic compressive and tensile loading experiments, deformation characteristics and energy dissipation were analyzed. The results show that the stress-strain curve of red sandstone has an obvious memory effect in the compressive and tensile loading stages. The strains at peak stresses and residual strains increase with the cycle number. Energy dissipation, defined as the area of the hysteresis loop in the stress-strain curves, increases nearly in a power function with the cycle number. Creep test of the red sandstone was also conducted. Results show that the creep curve under each compressive or tensile stress level can be divided into decay and steady stages, which cannot be described by the conventional Burgers model. Therefore, an improved Burgers creep model of rock material is constructed through viscoplastic mechanics, which agrees very well with the experimental results and can describe the creep behavior of red sandstone better than the Burgers creep model.

Anomalously high porosity in subduction inputs to the Nankai Trough (SW Japan) potentially caused by volcanic ash and pumice

Science.gov (United States)

Huepers, A.; Ikari, M.; Underwood, M.; Kopf, A.

2013-12-01

At convergent margins, the sedimentary section seaward of the trench on the subducting oceanic lithosphere provides the source material for accretionary prisms and eventually becomes the host rock of the plate boundary megathrust. The mechanical properties of the sediments seaward of the subduction zone have therefore a first order control on subduction zone forearc mechanics and hydrogeology. At the Nankai Trough (SW Japan) the majority of sediment approaching the subduction zone is clay-rich. Scientific drilling expeditions in the framework of the Ocean Drilling Program (ODP) and the Integrated Ocean Drilling Program (IODP) have revealed an anomalous zone of high porosity in a major lithologic unit known as the Upper Shikoku Basin facies (USB), which is associated with elevated volcanic ash content and high amounts of silica in the interstitial water. The existence of the high porosity zone has previously been associated with advanced silica cementation, driven by the dual diagenetic transition of opal-A to opal-CT, and opal-CT to quartz. However, temperature estimates from recent drilling expeditions offshore the Kii peninsula reveal different in situ temperatures at the proposed diagenetic boundary in the Shikoku Basin. Furthermore, laboratory measurements using core samples from the USB show that cohesive strength is not elevated in the high porosity zone, suggesting that a process other than cementation may be responsible. The USB sediment is characterized by abundant volcanic ash and pumice, therefore the high porosity zone in the USB may be closely linked to the mechanical behavior of this phase. We conducted consolidation tests in the range 0.1 to 8 MPa effective vertical stress on artificial ash-smectite and pumice-smectite mixtures, as well as intact and remolded natural samples from the IODP Sites C0011 and C0012 to investigate the role of the volcanic constituent on porosity loss with progressive burial. Our results show that both remolded and intact

Coastal dune facies, Permian Cutler Formation (White Rim Sandstone), Capitol Reef National Park area, southern Utah

Science.gov (United States)

Kamola, Diane L.; Chan, Marjorie A.

1988-04-01

The Permian Cutler Formation (White Rim Sandstone) in the Capitol Reef National Park area in southern Utah is an excellent example of a coastal dune complex subjected to periodic flooding by marine waters. Wind-ripple, grainfall and grainflow laminae compose the cross-sets deposited by eolian dunes. However, wave-reworked structures such as oscillation ripples, the occurrence of the characteristically marine trace fossils Thalassinoides and Chondrites, and interfingering marine carbonate beds of the Kaibab Formation collectively indicate marine interaction with the eolian environment. Four facies are distinguished: cross-stratified sandstone, burrowed to bioturbated sandstone, brecciated and deformed sandstone, and ripple-laminated sandstone and thin carbonate beds. One unusual aspect of the cross-stratified sandstone facies is the abundance of coarse-grained sand. Coarse-grained sand is atypical in many ancient eolian slipface deposits, but occurs here in large slipface foresets as both grainflow and wind-ripple deposits. No water-laid structures are found in these slipface deposits. Coarse-grained sand was probably transported to the Cutler shoreline by fluvial systems draining the Uncompahgre Uplift to the east, and then concentrated as coarse-grained ripples in interdune areas. Some of these coarse-grained ripples migrated up the stoss side of the dunes and accumulations of coarse-grained sand avalanched down the crest to form grainflow deposits. An extensive amount of soft-sediment deformation is indicated by the presence of convolute bedding and brecciation. These features occur near the zone of interfingering with marine carbonate beds of the Kaibab Formation. The water-saturated and moist conditions required for extensive deformation may have been controlled by the proximity of these sandstones to the shoreline, and fluctuations in the associated groundwater table.

Seal evaluation and confinement screening criteria for beneficial carbon dioxide storage with enhanced coal bed methane recovery in the Pocahontas Basin, Virginia

Science.gov (United States)

Grimm, R.P.; Eriksson, K.A.; Ripepi, N.; Eble, C.; Greb, S.F.

2012-01-01

The geological storage of carbon dioxide in Appalachian basin coal seams is one possible sink for sequestration of greenhouse gases, with the added benefit of enhanced-coal bed methane (ECBM) recovery. The Pocahontas Basin (part of the central Appalachian Basin) of southwestern Virginia is a major coal bed methane (CBM) province with production mostly from coal beds in the Lower Pennsylvanian Pocahontas and New River formations. As part of the Southeast Regional Carbon Sequestration Partnership's Phase II research program, a CO 2-injection demonstration well was installed into Lower Pennsylvanian coal bed-methane producing strata in southwest Virginia. Samples of siliciclastic lithologies above coal beds in this Oakwood Field well, and from several other cores in the Nora Field were taken to establish a baseline of the basic confinement properties of overlying strata to test seal competency at local and regional scales.Strata above CBM-producing coal beds in the Pocahontas and New River formations consist of dark-gray shales; silty gray shales; heterolithic siltstones, sandstones, and shales; lithic sandstones, and quartzose sandstones. Standard measurements of porosity, permeability and petrography were used to evaluate potential leakage hazards and any possible secondary storage potential for typical lithologies. Both lithic- and quartz-rich sandstones exhibit only minor porosity, with generally low permeability (Member. Analyses of 1500 geophysical logs in southwest Virginia indicate that this unit is moderately thick (>50ft, 15m), laterally continuous (>3000km 2), and a homogenous shale, which coarsens upward into siltstone and sandstone, or is truncated by sandstone. Calculations from two mercury injection capillary porosimetry tests of the shale indicate that a displacement entry pressure of 207psi (1427kPa) would generate an estimated seal capacity of 1365ft (416m) of CO 2 before buoyant leakage. Scanning electron microscopy indicates a microfabric of narrow

Porosity Measurements and Analysis for Metal Additive Manufacturing Process Control.

Science.gov (United States)

Slotwinski, John A; Garboczi, Edward J; Hebenstreit, Keith M

2014-01-01

Additive manufacturing techniques can produce complex, high-value metal parts, with potential applications as critical metal components such as those found in aerospace engines and as customized biomedical implants. Material porosity in these parts is undesirable for aerospace parts - since porosity could lead to premature failure - and desirable for some biomedical implants - since surface-breaking pores allows for better integration with biological tissue. Changes in a part's porosity during an additive manufacturing build may also be an indication of an undesired change in the build process. Here, we present efforts to develop an ultrasonic sensor for monitoring changes in the porosity in metal parts during fabrication on a metal powder bed fusion system. The development of well-characterized reference samples, measurements of the porosity of these samples with multiple techniques, and correlation of ultrasonic measurements with the degree of porosity are presented. A proposed sensor design, measurement strategy, and future experimental plans on a metal powder bed fusion system are also presented.

Mathematical aspects of multi-porosity continua

CERN Document Server

Straughan, Brian

2017-01-01

This book is devoted to describing theories for porous media where such pores have an inbuilt macro structure and a micro structure. For example, a double porosity material has pores on a macro scale, but additionally there are cracks or fissures in the solid skeleton. The actual body is allowed to deform and thus the underlying theory is one of elasticity. Various different descriptions are reviewed. Chapter 1 introduces the classical linear theory of elastodynamics together with uniqueness and continuous dependence results. Chapters 2 and 3 review developments of theories for double and triple porosity using a pressure-displacement structure and also using voids-displacement. Chapter 4 compares various aspects of the pressure-displacement and voids-displacement theories via uniqueness studies and wave motion analysis. Mathematical analyses of double and triple porosity materials are included concentrating on uniqueness and stability studies in chapters 5 to 7. In chapters 8 and 9 the emphasis is on wa...

Effect of Matrix-Wellbore Flow and Porosity on Pressure Transient Response in Shale Formation Modeling by Dual Porosity and Dual Permeability System

Directory of Open Access Journals (Sweden)

Daolun Li

2015-01-01

Full Text Available A mathematical dual porosity and dual permeability numerical model based on perpendicular bisection (PEBI grid is developed to describe gas flow behaviors in shale-gas reservoirs by incorporating slippage corrected permeability and adsorbed gas effect. Parametric studies are conducted for a horizontal well with multiple infinite conductivity hydraulic fractures in shale-gas reservoir to investigate effect of matrix-wellbore flow, natural fracture porosity, and matrix porosity. We find that the ratio of fracture permeability to matrix permeability approximately decides the bottom hole pressure (BHP error caused by omitting the flow between matrix and wellbore and that the effect of matrix porosity on BHP is related to adsorption gas content. When adsorbed gas accounts for large proportion of the total gas storage in shale formation, matrix porosity only has a very small effect on BHP. Otherwise, it has obvious influence. This paper can help us understand the complex pressure transient response due to existence of the adsorbed gas and help petroleum engineers to interpret the field data better.

Experimental Investigation on Shock Mechanical Properties of Red Sandstone under Preloaded 3D Static Stresses

Directory of Open Access Journals (Sweden)

Niu Yong

2015-11-01

Full Text Available Triaxial impact mechanical performance experiment was performed to study the mechanical properties of red sandstone subjected to three-dimensional (3D coupled static and dynamic loads, i.e., three confining pressures (0, 5, and 10 MPa and three axial pressures (11, 27, and 43 MPa. A modified 3D split Hopkinson pressure bar testing system was used. The change trend in the deformation of red sandstone and the strength and failure modes under axial pressures and confining pressures were analyzed. Results show that, when the confining pressure is constant, the compressive strength, secant modulus, and energy absorbed per unit volume of red sandstone initially increases and subsequently decreases, whereas the average strain rate exhibits an opposite trend. When the axial pressure is constant, both the compressive strength and secant modulus of red sandstone are enhanced, but the average strain rate is decreased with increasing confining pressure. The energy absorbed per unit volume is initially increased and subsequently decreased as the confining pressure increases. Red sandstone exhibits a cone-shaped compression–shear failure mode under the 3D coupled static and dynamic loads. The conclusions serve as theoretical basis on the mechanical properties of deep medium-strength rock under a high ground stress and external load disturbance condition

Functional grading of metal foam cores for yield-limited lightweight sandwich beams

International Nuclear Information System (INIS)

Conde, Yves; Pollien, Arnaud; Mortensen, Andreas

2006-01-01

We show that grading the porosity in a bent metal skin/metal foam core sandwich can generate significant weight savings in yield-limited design when, and only when, there is a gradient in the applied moment along the sandwich beam

Causes and remedies for porosity in composite manufacturing

Science.gov (United States)

Fernlund, G.; Wells, J.; Fahrang, L.; Kay, J.; Poursartip, A.

2016-07-01

Porosity is a challenge in virtually all composite processes but in particular in low pressure processes such as out of autoclave processing of prepregs, where the maximum pressure is one atmosphere. This paper discusses the physics behind important transport phenomena that control porosity and how we can use our understanding of the underlying science to develop strategies to achieve low porosity for these materials and processes in an industrial setting. A three step approach is outlined that addresses and discusses: gas evacuation of trapped air, volatiles and off-gassing, and resin infiltration of evacuated void space.

Application of Rock-Eval pyrolysis to the detection of hydrocarbon property in sandstone-type uranium deposits

International Nuclear Information System (INIS)

Sun Ye; Li Ziying; Guo Qingyin; Xiao Xinjian

2006-01-01

Rock-Eval pyrolysis is introduced into the research of uranium geology by means of oil-gas geochemical evaluation. Hydrocarbon (oil-gas) components in DS sandstone-type uranium deposit are detected quantitatively. Through analyzing the oil-gas bearing categories of the uranium-bearing sandstones, the internal relationships between the uranium deposit and the oil-gas are revealed. Rock-Eval pyrolysis is an effective method to study the interaction between inorganic and organic matters, and should be extended to the study of sandstone-type uranium deposits. (authors)

Physical properties of Martian meteorites: Porosity and density measurements

Science.gov (United States)

Coulson, Ian M.; Beech, Martin; Nie, Wenshuang

Martian meteorites are fragments of the Martian crust. These samples represent igneous rocks, much like basalt. As such, many laboratory techniques designed for the study of Earth materials have been applied to these meteorites. Despite numerous studies of Martian meteorites, little data exists on their basic structural characteristics, such as porosity or density, information that is important in interpreting their origin, shock modification, and cosmic ray exposure history. Analysis of these meteorites provides both insight into the various lithologies present as well as the impact history of the planet's surface. We present new data relating to the physical characteristics of twelve Martian meteorites. Porosity was determined via a combination of scanning electron microscope (SEM) imagery/image analysis and helium pycnometry, coupled with a modified Archimedean method for bulk density measurements. Our results show a range in porosity and density values and that porosity tends to increase toward the edge of the sample. Preliminary interpretation of the data demonstrates good agreement between porosity measured at 100× and 300× magnification for the shergottite group, while others exhibit more variability. In comparison with the limited existing data for Martian meteorites we find fairly good agreement, although our porosity values typically lie at the low end of published values. Surprisingly, despite the increased data set, there is little by way of correlation between either porosity or density with parameters such as shock effect or terrestrial residency. Further data collection on additional meteorite samples is required before more definitive statements can be made concerning the validity of these observations.

Different effects of temperature and salinity on permeability reduction by fines migration in Berea sandstone

DEFF Research Database (Denmark)

Rosenbrand, Esther; Kjøller, Claus; Riis, Jacob Fabricius

2015-01-01

Hot water injection into geothermal aquifers is considered in order to store energy seasonally. Berea sandstone is often used as a reference formation to study mechanisms that affect permeability in reservoir sandstones. Both heating of the pore fluid and reduction of the pore fluid salinity can...

METHANE HYDRATE PRODUCTION FROM ALASKAN PERMAFROST

Energy Technology Data Exchange (ETDEWEB)

Richard Sigal; Kent Newsham; Thomas Williams; Barry Freifeld; Timothy Kneafsey; Carl Sondergeld; Shandra Rai; Jonathan Kwan; Stephen Kirby; Robert Kleinberg; Doug Griffin

2005-02-01

part of the Ugnu and throughout the West Sak. No hydrate-bearing zones were identified either in recovered core or on well logs. The base of the permafrost was found at about 1260 ft. With the exception of the deepest sands in the West Sak and some anomalous thin, tight zones, all sands recovered (after thawing) are unconsolidated with high porosity and high permeability. At 800 psi, Ugnu sands have an average porosity of 39.3% and geometrical mean permeability of 3.7 Darcys. Average grain density is 2.64 g/cc. West Sak sands have an average porosity of 35.5%, geometrical mean permeability of 0.3 Darcys, and average grain density of 2.70 g/cc. There were several 1-2 ft intervals of carbonate-cemented sandstone recovered from the West Sak. These intervals have porosities of only a few percent and very low permeability. On a well log they appear as resistive with a high sonic velocity. In shallow sections of other wells these usually are the only logs available. Given the presence of gas in Hot Ice No. 1, if only resistivity and sonic logs and a mud log had been available, tight sand zones may have been interpreted as containing hydrates. Although this finding does not imply that all previously mapped hydrate zones are merely tight sands, it does add a note of caution to the practice of interpreting the presence of hydrates from old well information. The methane hydrate stability zone below the Hot Ice No. 1 location includes thick sections of sandstone and conglomerate which would make excellent reservoir rocks for hydrates and below the permafrost zone shallow gas. The Ugnu formation comprises a more sand-rich section than does the West Sak formation, and the Ugnu sands when cleaned and dried are slightly more porous and significantly more permeable than the West Sak.

Contributed Review: Nuclear magnetic resonance core analysis at 0.3 T

International Nuclear Information System (INIS)

Mitchell, Jonathan; Fordham, Edmund J.

2014-01-01

Nuclear magnetic resonance (NMR) provides a powerful toolbox for petrophysical characterization of reservoir core plugs and fluids in the laboratory. Previously, there has been considerable focus on low field magnet technology for well log calibration. Now there is renewed interest in the study of reservoir samples using stronger magnets to complement these standard NMR measurements. Here, the capabilities of an imaging magnet with a field strength of 0.3 T (corresponding to 12.9 MHz for proton) are reviewed in the context of reservoir core analysis. Quantitative estimates of porosity (saturation) and pore size distributions are obtained under favorable conditions (e.g., in carbonates), with the added advantage of multidimensional imaging, detection of lower gyromagnetic ratio nuclei, and short probe recovery times that make the system suitable for shale studies. Intermediate field instruments provide quantitative porosity maps of rock plugs that cannot be obtained using high field medical scanners due to the field-dependent susceptibility contrast in the porous medium. Example data are presented that highlight the potential applications of an intermediate field imaging instrument as a complement to low field instruments in core analysis and for materials science studies in general

Low field NMR surface relaxivity studies of chalk and argillaceous sandstones

DEFF Research Database (Denmark)

Katika, Konstantina; Fordsmand, Henrik; Fabricius, Ida Lykke

2017-01-01

the accuracy of predictions of petrophysical properties of various rocks with the use of NMR spectrometry. We perform laboratory transverse relaxation (T2) measurements on water saturated Gorm field chalk, Stevns Klint chalk, Solsort field greensand and Berea sandstone. These rocks are of particular interest...... field chalk and Solsort field greensand have higher ρ at higher Larmor frequency. By contrast, ρ of the purely calcitic Stevns chalk and quartzitic Berea sandstone proved not to be affected by the changes in frequency. T2 distributions at temperatures ranging from 10 °C to 60 °C provided comparison...

Ultrasonic technique for measuring porosity of plasma-sprayed alumina coatings

Science.gov (United States)

Parthasarathi, S.; Tittmann, B. R.; Onesto, E. J.

1997-12-01

Porosity is an important factor in plasma-sprayed coatings, especially ceramic coatings. Excessive poros-ity can adversely affect the performance of the coated component in various ways. An ultrasonic nonde-structive measurement technique has been developed to measure porosity in plasma-sprayed alumina coatings. The technique is generic and can be extended to other ceramic coating systems. To test the tech-nique, freestanding alumina coatings with varying levels of porosity were fabricated via plasma spray. Samples with varying porosity, obtained through innovative fabrication techniques, were used to gener-ate a calibration curve. The ultrasonic velocity in the low-frequency range was found to be dependent on the density of freestanding coatings (measured via Archimedian techniques). This dependence is the basis of the development of a technique to measure the density of coatings.

Chalk porosity and sonic velocity versus burial depth

DEFF Research Database (Denmark)

Fabricius, Ida Lykke; Gommesen, Lars; Krogsbøll, Anette Susanne

2008-01-01

Seventy chalk samples from four formations in the overpressured Danish central North Sea have been analyzed to investigate how correlations of porosity and sonic velocity with burial depth are affected by varying mineralogy, fluid pressure, and early introduction of petroleum. The results show th...... for fluid pressure because the cementing ions originate from stylolites, which are mechanically similar to fractures. We find that cementation occurs over a relatively short depth interval.......Seventy chalk samples from four formations in the overpressured Danish central North Sea have been analyzed to investigate how correlations of porosity and sonic velocity with burial depth are affected by varying mineralogy, fluid pressure, and early introduction of petroleum. The results show...... that porosity and sonic velocity follow the most consistent depth trends when fluid pressure and pore-volume compressibility are considered. Quartz content up to 10% has no marked effect, but more than 5% clay causes lower porosity and velocity. The mineralogical effect differs between P-wave and shear velocity...

Assessment of spatial distrilbution of porosity and aquifer geohydraulic parameters in parts of the Tertiary – Quaternary hydrogeoresource of south-eastern Nigeria

Directory of Open Access Journals (Sweden)

N.J. George

2017-12-01

Full Text Available An integrated attempt exploring information deduced from extensive surface resistivity study in three Local Government Areas of Akwa Ibom State, Nigeria and data from hydrogeological sources obtained from water boreholes have been explored to economically estimate porosity and coefficient of permeability/hydraulic conductivity in parts of the clastic Tertiary – Quaternary sediments of the Niger Delta region. Generally, these parameters are predominantly estimated from empirical analysis of core samples and pumping test data generated from boreholes in the laboratory. However, this analysis is not only costly and time consuming, but also limited in areal coverage. The chosen technique employs surface resistivity data, core samples and pumping test data in order to estimate porosity and aquifer hydraulic parameters (transverse resistance, hydraulic conductivity and transmissivity. In correlating the two sets of results, Porosity and hydraulic conductivity were observed to be more elevated near the riverbanks. Empirical models utilising Archie’s, Waxman-Smits and Kozeny-Carman Bear relations were employed characterising the formation parameters with wonderfully deduced good fits. The effect of surface conduction occasioned by clay usually disregarded or ignored in Archie’s model was estimated to be 2.58 × 10−5 Siemens. This conductance can be used as a corrective factor to the conduction values obtained from Archie’s equation. Interpretation aided measures such as graphs, mathematical models and maps which geared towards realistic conclusions and interrelationship between the porosity and other aquifer parameters were generated. The values of the hydraulic conductivity estimated from Waxman-Smits model was approximately 9.6 × 10−5m/s everywhere. This revelation indicates that there is no pronounced change in the quality of the saturating fluid and the geological formations that serve as

The influence of climate on early and burial diagenesis of Triassic and Jurassic sandstones from the Norwegian – Danish Basin

DEFF Research Database (Denmark)

Weibel, Rikke; Olivarius, Mette; Kjøller, Claus

2017-01-01

Climate changes preserved in sandstones are documented by comparing the sediment composition and early diagenetic changes in sandstones deposited during arid to semi-arid conditions, the Skagerrak Formation, with sandstones of the Gassum Formation deposited in a humid well-vegetated environment...

Transport upscaling from pore- to Darcy-scale: Incorporating pore-scale Berea sandstone Lagrangian velocity statistics into a Darcy-scale transport CTRW model

Science.gov (United States)

Puyguiraud, Alexandre; Dentz, Marco; Gouze, Philippe

2017-04-01

For the past several years a lot of attention has been given to pore-scale flow in order to understand and model transport, mixing and reaction in porous media. Nevertheless we believe that an accurate study of spatial and temporal evolution of velocities could bring important additional information for the upscaling from pore to higher scales. To gather these pieces of information, we perform Stokes flow simulations on pore-scale digitized images of a Berea sandstone core. First, micro-tomography (XRMT) imaging and segmentation processes allow us to obtain 3D black and white images of the sample [1]. Then we used an OpenFoam solver to perform the Stokes flow simulations mentioned above, which gives us the velocities at the interfaces of a cubic mesh. Subsequently, we use a particle streamline reconstruction technique which uses the Eulerian velocity field previously obtained. This technique, based on a modified Pollock algorithm [2], enables us to make particle tracking simulations on the digitized sample. In order to build a stochastic pore-scale transport model, we analyze the Lagrangian velocity series in two different ways. First we investigate the velocity evolution by sampling isochronically (t-Lagrangian), and by studying its statistical properties in terms of one- and two-points statistics. Intermittent patterns can be observed. These are due to the persistance of low velocities over a characteristic space length. Other results are investigated, such as correlation functions and velocity PDFs, which permit us to study more deeply this persistence in the velocities and to compute the correlation times. However, with the second approach, doing these same analysis in space by computing the velocities equidistantly, enables us to remove the intermittency shown in the temporal evolution and to model these velocity series as a Markov process. This renders the stochastic particle dynamics into a CTRW [3]. [1] Gjetvaj, F., A. Russian, P. Gouze, and M. Dentz (2015

Porosity Variation in Cenozoic and Upper Chalk from the Ontong Java Pleateau

DEFF Research Database (Denmark)

Borre, Mai Kirstine

1997-01-01

Porosity was obtained from matrix- and intraparticle porosity assessed from image analysis of backscattered electron micrographs of 3000x and 300x magnification. Comparing porosity assessed from image analysis with porosity measured by index properties, it was seen that image analysis data at 300...

Diagenetic Evolution and Reservoir Quality of Sandstones in the North Alpine Foreland Basin: A Microscale Approach.

Science.gov (United States)

Gross, Doris; Grundtner, Marie-Louise; Misch, David; Riedl, Martin; Sachsenhofer, Reinhard F; Scheucher, Lorenz

2015-10-01

Siliciclastic reservoir rocks of the North Alpine Foreland Basin were studied focusing on investigations of pore fillings. Conventional oil and gas production requires certain thresholds of porosity and permeability. These parameters are controlled by the size and shape of grains and diagenetic processes like compaction, dissolution, and precipitation of mineral phases. In an attempt to estimate the impact of these factors, conventional microscopy, high resolution scanning electron microscopy, and wavelength dispersive element mapping were applied. Rock types were established accordingly, considering Poro/Perm data. Reservoir properties in shallow marine Cenomanian sandstones are mainly controlled by the degree of diagenetic calcite precipitation, Turonian rocks are characterized by reduced permeability, even for weakly cemented layers, due to higher matrix content as a result of lower depositional energy. Eocene subarkoses tend to be coarse-grained with minor matrix content as a result of their fluvio-deltaic and coastal deposition. Reservoir quality is therefore controlled by diagenetic clay and minor calcite cementation.Although Eocene rocks are often matrix free, occasionally a clay mineral matrix may be present and influence cementation of pores during early diagenesis. Oligo-/Miocene deep marine rocks exhibit excellent quality in cases when early cement is dissolved and not replaced by secondary calcite, mainly bound to the gas-water contact within hydrocarbon reservoirs.

Porosity and permeability evolution of vesicular basalt reservoirs with increasing depth: constraints from the Big Island of Hawai'i

Science.gov (United States)

Millett, John; Haskins, Eric; Thomas, Donald; Jerram, Dougal; Planke, Sverre; Healy, Dave; Kück, Jochem; Rossetti, Lucas; Farrell, Natalie; Pierdominici, Simona

2017-04-01

Volcanic reservoirs are becoming increasingly important in the targeting of petroleum, geothermal and water resources globally. However, key areas of uncertainty in relation to volcanic reservoir properties during burial in different settings remain. In this contribution, we present results from borehole logging and sampling operations within two fully cored c. 1.5 km deep boreholes, PTA2 and KMA1, from the Humúula saddle region on the Big Island of Hawai'i. The boreholes were drilled as part of the Humu'ula Groundwater Research Project (HGRP) between 2013-2016 and provide unique insights into the evolution of pore structure with increasing burial in a basaltic dominated lava sequence. The boreholes encounter mixed sequences of 'a'ā, pāhoehoe and transitional lava flows along with subsidiary intrusions and sediments from the shield to post-shield phases of Mauna Kea. Borehole wireline data including sonic, spectral gamma and Televiewer imagery were collected along with density, porosity, permeability and ultrasonic velocity laboratory measurements from core samples. A range of intra-facies were sampled for analysis from various depths within the two boreholes. By comparison with core data, the potential for high resolution Televiewer imaging to reveal spectacular intra-facies features including individual vesicles, vesicle segregations, 'a'ā rubble zones, intrusive contacts, and intricate pāhoehoe lava flow lobe morphologies is demonstrated. High quality core data enables the calibration of Televiewer facies enabling improved interpretation of volcanic reservoir features in the more common exploration scenario where core is absent. Laboratory results record the ability of natural vesicular basalt samples to host very high porosity (>50%) and permeability (>10 darcies) within lava flow top facies which we demonstrate are associated with vesicle coalescence and not micro-fractures. These properties may be maintained to depths of c. 1.5 km in regions of limited

Possible application of underground leaching of uranium in ''sandstone'' deposits by drilling method

International Nuclear Information System (INIS)

Bareja, E.

1988-01-01

Underground leaching as the method for excavation of uranium from its sandstone deposits is applied in many countries. A preliminary examination of a possible use of this method to sandstone deposits in Poland suggests it to be analysed against the uranium mineralization, noted within sediments of the Lower Triassic age in the Peribaltic Syneclise in the Krynica Morska - Paslek area. Before a definite decision on such exploitation of uranium, geologic and hydrogeologic conditions should be studied of individual uranium-bearing beds, particularly their permeability and insulation by impermeable claystone series as well as extraction of uranium from its bearing sandstones. The depth at which uranium-bearing beds occur, forms a very important item. The depth at which uranium ores described in literature and exploited by this method occur, does not exceed 700 m. 7 refs. (author)

Stable isotopic mass balance in sandstone-shale couplets. An example from the Neogene Pannonian Basin

International Nuclear Information System (INIS)

Matyas, J.; Geologisches Institut.

1996-01-01

Oxygen isotopic ratios of carbonate cements in the Neogene sandstones of the Pannonian Basin show distinct variations: early calcites 3-6 per mille lighter than the late calcites from the same location and depth. This shift is thought to be related to the isotopically heavy oxygen released from the mixed-layer illite/smectite during illitisation. For sandstones dominated by compactional flow, closed system mass balance calculations predict an isotopic shift comparable to that deducted from petrographic and geochemical observations. The model suggests that variations of geothermal gradient has little effect on isotopic evolution; much more significant is the sandstone: shale ratio in the couplets. (author)

Porosity in Ocean Racing Yacht Composites: a Review

Science.gov (United States)

Baley, Christophe; Lan, Marine; Davies, Peter; Cartié, Denis

2015-02-01

Ocean racing yachts are mainly manufactured from carbon/epoxy composites similar to those used by the aeronautical industry but, with some exceptions such as masts, these structures are not produced in autoclaves. This leads to the presence of higher porosity levels. This paper will first present the different types of porosity found in traditional racing yacht structures. Difficulties in evaluating defect levels will then be discussed and published work characterizing the influence of defects will be reviewed. Current developments to improve racing yacht composite quality such as thin ply technology, out-of-autoclave processing and automated fibre placement will then be described, and their implications for porosity will be discussed.

Regional diagenesis of sandstone in the Upper Jurassic Morrison Formation, San Juan Basin, New Mexico and Colorado

International Nuclear Information System (INIS)

Hansley, P.L.

1990-01-01

The author reports that early authigenic mineral assemblages and vitroclastic textures are very well preserved in upper sandstones of the Upper Jurassic Morrison Formation. The distributions of the authigenic minerals were controlled, in part, by chemical gradients in a large saline, alkaline lake (Lake T'oo'dichi) that existed in late Morrison time. Sandstones on lake margins were cemented by smectite and silica, whereas sandstones nearer the lake center, in which waters were most saline and alkaline, were cemented by zeolites. Diagenetic alterations in sandstones were promoted by alkaline interstitial waters that emanated from adjacent fine-grained, tuffaceous lake beds. Metastable phases that precipitated first were replaced relatively quickly by more stable, ordered phases in the geochemically favorable environment of the closed basin setting. Elevation of temperatures above the geothermal gradient was proved by the influx of warm, deep-basin waters that locally modified early diagenetic assemblages during burial diagenesis. In organic- (and commonly also uranium ore-) bearing sandstones located primarily in the southern part of the basin, complex diagenetic assemblages resulted from water/rock reactions involving soluble organic complexes

Properties and durability assessment of glauconitic sandstone: A case study on Zamel sandstone from Bohemian Cretaceous Basin (Czech Republic)

Czech Academy of Sciences Publication Activity Database

Martinec, Petr; Vavro, M.; Ščučka, Jiří; Mašláň, M.

2010-01-01

Roč. 115, 3/4 (2010), s. 175-181 ISSN 0013-7952 R&D Projects: GA ČR GP101/07/P512; GA ČR(CZ) GA103/07/1662 Institutional research plan: CEZ:AV0Z30860518 Keywords : building stone * sandstone * physical properties Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.442, year: 2010 http://www.sciencedirect.com/science

Distribution of K, Na, Th and U in sandstones and shales from western Shikoku, Japan

International Nuclear Information System (INIS)

Ishihara, Shunso; Sakamaki, Yukio; Mochizuki, Tsunekazu; Terashima, Shigeru; Endo, Yuji

1981-01-01

The regional variation of K, Na, Th and U distributions was studied on 58 sandstones, 81 shales and 3 green schists from the sedimentary terrains across western Shikoku. The geological structure of the studied district is explained. The regional characteristics of the sedimentary rocks are best demonstrated in the composition of the sandstones. The sandstones, in the source areas of which granitic and rhyolitic rocks exist and which have been deposited rapidly, were rich in K, whereas those derived mainly from mafic volcanic areas showed high Na content. The sandstones of the Shimanto Supergroup had the intermediate values, and K and K + Na contents became low in the south where the younger Upper Shimanto Group is exposed. Th and U in both sandstones and shales were highest in the Izumi Group, and generally low in the Shimanto Supergroup. The black shales of the Shimanto Supergroup did not show U-anomaly. In each group, highly matured rocks gave slightly higher Th/U ratio. Highly matured polycyclic sediments contained the least amount of radioactive elements. The radioactive anomaly due to the anomalous K contained in sericite, and that due to U in black shale were found in Chichibu and Sambosan belts. Similar anomaly was discovered in the foot wall of Mn deposits in the same zone. The possibility of anomalous U may be the least in the Shimanto Supergroup. (Kako, I.)

Use of digital image analysis to estimate fluid permeability of porous materials: Application of two-point correlation functions

International Nuclear Information System (INIS)

Berryman, J.G.; Blair, S.C.

1986-01-01

Scanning electron microscope images of cross sections of several porous specimens have been digitized and analyzed using image processing techniques. The porosity and specific surface area may be estimated directly from measured two-point spatial correlation functions. The measured values of porosity and image specific surface were combined with known values of electrical formation factors to estimate fluid permeability using one version of the Kozeny-Carman empirical relation. For glass bead samples with measured permeability values in the range of a few darcies, our estimates agree well ( +- 10--20%) with the measurements. For samples of Ironton-Galesville sandstone with a permeability in the range of hundreds of millidarcies, our best results agree with the laboratory measurements again within about 20%. For Berea sandstone with still lower permeability (tens of millidarcies), our predictions from the images agree within 10--30%. Best results for the sandstones were obtained by using the porosities obtained at magnifications of about 100 x (since less resolution and better statistics are required) and the image specific surface obtained at magnifications of about 500 x (since greater resolution is required)

Endolithic algae of semi-desert sandstones: systematic, biogeographic and ecophysiologic investigations

International Nuclear Information System (INIS)

Bell, R.A.

1986-01-01

Investigations were conducted into the ecology of an unusual algal community in northern Arizona. These microorganisms are called endolithic algae because they occur beneath the surface of rocks. Eighteen taxa, including representatives of both eukaryotic and prokaryotic genera, were isolated from below the surface of eight sandstones in four semi-desert and cold temperate biomes of the Colorado Plateau. As the macroclimate of the area changes from cold temperature desert scrub to cold temperate forest the taxonomic composition of the endolithic algal communities shifts from domination by coccoid blue-green algae to domination by coccoid and sarcinoid green algae. The algal communities varied in generic composition, chlorophyll a content, and in their location within the different sandstones. Investigations into the microclimate of the endolithic algal zone in two adjacent but differently-colored sections (white and brown) of Coconino sandstone have demonstrated differences between the environment above the rock surface and that just beneath the surface. In seasonal samples of the Coconino sandstone, chlorophyll a content ranged from 50 to 100 mg x m -2 in the white rock and 8 to 45 mg x m -2 in the brown rock. Primary production (as measured by 14 CO 2 incorporation) displayed marked seasonal patterns that appear to be correlated to the environmental conditions within the rocks as opposed to those outside the rocks. The widespread distribution of certain algae in the endolithic habitats of the Colorado Plateau and their presence in rocks at quite distant locations suggests that the endolithic habitat may be utilized by algae whenever it provides more favorable conditions than the surrounding surfaces

The Collyhurst Sandstone as a secondary storage unit for CCS in the East Irish Sea Basin (UK)

Science.gov (United States)

Gamboa, D.; Williams, J. D. O.; Kirk, K.; Gent, C. M. A.; Bentham, M.; Schofield, D. I.

2016-12-01

Carbon Capture and Storage (CCS) is key technology for low-carbon energy and industry. The UK hosts a large CO2 storage potential offshore with an estimated capacity of 78 Gt. The East Irish Sea Basin (EISB) is the key area for CCS in the western UK, with a CO2 storage potential of 1.7 Gt in hydrocarbon fields and in saline aquifers within the Triassic Sherwood Sandstone Formation. However, this theoretical storage capacity does not consider the secondary storage potential in the lower Permian Collyhurst Sandstone Formation. 3D seismic data were used to characterise the Collyhurst Sandstone Formation in the EISB. On the southern basin domain, numerous fault-bound blocks limit the lateral continuity of the sandstone strata, while on the northern domain the sandstones are intersected by less faults. The caprock for the Collyhurst sandstones is variable. The Manchester Marls predominate in the south, transitioning to the St. Bees evaporites towards the north. The evaporites in the EISB cause overburden faults to terminate or detach along Upper Permian strata, limiting the deformation of the underlying reservoir units. Five main storage closures have been identified in the Permian strata. In the southern and central area these are predominantly fault bounded, occurring at depths over 1000m. Despite the higher Collyhurst sandstone thickness in the southern IESB, the dolomitic nature of the caprock constitutes a storage risk in this area. Closures in the northern area are deeper (around 2000-2500m) and wider, reaching areas of 34Km2, and are overlain by evaporitic caprocks. The larger Collyhurst closures to the north underlie large Triassic fields with high storage potential. The spatial overlap favours storage plans including secondary storage units in the EISB. The results of this work also expand the understanding of prospective areas for CO2 sequestration in the East Irish Sea Basin in locations where the primary Sherwood Sandstone Formation is either too shallow

Radiographically detectable intracortical porosity

International Nuclear Information System (INIS)

Meema, H.E.

1986-01-01

Since the measurement of intracortical resorptive spaces by histologic methods is difficult and very few data are available in normal humans, we have measured their lengths and widths and calculated the intracortical porosity in metacarpals and phalanges of 79 normal women and 69 normal men, using fine-detail radiographs of the hands and a computerized semi-automatic image analysis system (Zeiss MOP-3), this being the first study of this kind. Several methodological problems were solved satisfactorily, and the results of this study could serve as a data bank for further investigations concerned with intracortical resorption. Significant differences were found between age and sex versus several intracortical resorptive parameters; also significant correlations were found with age in some cases. Normal intracortical porosity was found to be about three times greater in the proximal phalanges than in the metacarpals. It is concluded that this methodology could be used for further studies of intracortical resorption in osteoporosis and other metabolic bone diseases. (orig.)

Porosity of porcine bladder acellular matrix: impact of ACM thickness.

Science.gov (United States)

Farhat, Walid; Chen, Jun; Erdeljan, Petar; Shemtov, Oren; Courtman, David; Khoury, Antoine; Yeger, Herman

2003-12-01

The objectives of this study are to examine the porosity of bladder acellular matrix (ACM) using deionized (DI) water as the model fluid and dextran as the indicator macromolecule, and to correlate the porosity to the ACM thickness. Porcine urinary bladders from pigs weighing 20-50 kg were sequentially extracted in detergent containing solutions, and to modify the ACM thickness, stretched bladders were acellularized in the same manner. Luminal and abluminal ACM specimens were subjected to fixed static DI water pressure (10 cm); and water passing through the specimens was collected at specific time interval. While for the macromolecule porosity testing, the diffusion rate and direction of 10,000 MW fluoroescein-labeled dextrans across the ACM specimens mounted in Ussing's chambers were measured. Both experiments were repeated on the thin stretched ACM. In both ACM types, the fluid porosity in both directions did not decrease with increased test duration (3 h); in addition, the abluminal surface was more porous to fluid than the luminal surface. On the other hand, when comparing thin to thick ACM, the porosity in either direction was higher in the thick ACM. Macromolecule porosity, as measured by absorbance, was higher for the abluminal thick ACM than the luminal side, but this characteristic was reversed in the thin ACM. Comparing thin to thick ACM, the luminal side in the thin ACM was more porous to dextran than in the thick ACM, but this characteristic was reversed for the abluminal side. The porcine bladder ACM possesses directional porosity and acellularizing stretched urinary bladders may increase structural density and alter fluid and macromolecule porosity. Copyright 2003 Wiley Periodicals, Inc. J Biomed Mater Res 67A: 970-974, 2003

Remote sensing information acquisition of paleo-channel sandstone-type uranium deposit in Nuheting area

International Nuclear Information System (INIS)

Liu Jianjun

2000-01-01

The author briefly describes the genesis and ore-formation mechanism of paleo-channel sandstone-type uranium deposit in Nuheting area. Techniques such as remote sensing digital image data processing and data enhancement, as well as 3-dimension quantitative analysis of drill hole data are applied to extract information on metallogenic environment of paleo-channel sandstone-type uranium deposit and the distribution of paleo-channel

Temperature Effects on Stiffness Moduli of Reservoir Sandstone from the Deep North Sea

DEFF Research Database (Denmark)

Orlander, Tobias; Andreassen, Katrine Alling; Fabricius, Ida Lykke

We investigate effect of testing temperature on the dynamic frame stiffness of quartz-bearing North Sea sandstone from depths of 5 km. We show that at low stress levels, the rock frame stiffens with increasing temperature and we propose an explanation for the controlling mechanisms. While...... temperature. This is unfortunate and hence, we designed a testing program with the intension of separating and quantifying effects of temperature and stress, specifically for the sandstone material subject to this study....

Effect of porosity on the tensile properties of low ductility aluminum alloys

Directory of Open Access Journals (Sweden)

Gustavo Waldemar Mugica

2004-06-01

Full Text Available The literature contains reports of several studies correlating the porosity and mechanical properties of aluminum alloys. Most of these studies determine this correlation based on the parameter of global volumetric porosity. These reports, however, fail to separate the effects of microstructural features and porosity on alloys, though recognizing the influence of the latter on their mechanical properties. Thus, when the decrease in tensile strength due to the porosity effect is taken into account, the findings are highly contradictory. An analysis was made of the correlation between mechanical properties and global volumetric porosity and volumetric porosity in the fracture, as well as of the beta-Al5FeSi phase present in 380 aluminum alloy. Our findings indicate that mechanical properties in tension relating to global volumetric porosity lead to overestimations of the porosity effect in detriment to the mechanical properties. Moreover, the proposed models that take into account the effects of particles, both Si and beta-Al5FeSi, are unapplicable to low ductility alloys.

Homogeneity vs. Heterogeneity of Porosity in Boom Clay

International Nuclear Information System (INIS)

Hemes, Susanne; Desbois, Guillaume; Urai, Janos L.; De Craen, Mieke; Honty, Miroslav

2013-01-01

Microstructural investigations on Boom Clay at nano- to micrometer scale, using BIB-SEM methods, result in porosity characterization for different mineral phases from direct observations on high resolution SE2-images of representative elementary areas (REAs). High quality, polished surfaces of cross-sections of ∼ 1 mm 2 size were produced on three different samples from the Mol-Dessel research site (Belgium). More than 33,000 pores were detected, manually segmented and analyzed with regard to their size, shape and orientation. Two main pore classes were defined: Small pores (< 500 nm (ED)) within the clay matrices of samples and =big' pores (> 500 nm (ED)) at the interfaces between clay and non-clay mineral (NCM) grains. Samples investigated show similar porosities regarding the first pore-class, but differences occur at the interfaces between clay matrix and NCM grains. These differences were interpreted to be due to differences in quantitative mineralogy (amount of non-clay mineral grains) and grain-size distributions between samples investigated. Visible porosities were measured as 15 to 17 % for samples investigated. Pore-size distributions of pores in clay are similar for all samples, showing log-normal distributions with peaks around 60 nm (ED) and more than 95 % of the pores being smaller than 500 nm (ED). Fitting pore-size distributions using power-laws with exponents between 1.56 and 1.7, assuming self-similarity of the pore space, thus pores smaller than the pore detection resolution following the same power-laws and using these power-laws for extrapolation of pore-size distributions below the limit of pore detection resolution, results in total estimated porosities between 20 and 30 %. These results are in good agreement with data known from Mercury Porosimetry investigations (35-40 % porosity) and water content porosity measurements (∼ 36 %) performed on Boom Clay. (authors)

Can porosity affect the hyperspectral signature of sandy landscapes?

Science.gov (United States)

Baranoski, Gladimir V. G.; Kimmel, Bradley W.

2017-10-01

Porosity is a fundamental property of sand deposits found in a wide range of landscapes, from beaches to dune fields. As a primary determinant of the density and permeability of sediments, it represents a central element in geophysical studies involving basin modeling and coastal erosion as well as geoaccoustics and geochemical investigations aiming at the understanding of sediment transport and water diffusion properties of sandy landscapes. These applications highlight the importance of obtaining reliable porosity estimations, which remains an elusive task, notably through remote sensing. In this work, we aim to contribute to the strengthening of the knowledge basis required for the development of new technologies for the remote monitoring of environmentally-triggered changes in sandy landscapes. Accordingly, we employ an in silico investigation approach to assess the effects of porosity variations on the reflectance of sandy landscapes in the visible and near-infrared spectral domains. More specifically, we perform predictive computer simulations using SPLITS, a hyperspectral light transport model for particulate materials that takes into account actual sand characterization data. To the best of our knowledge, this work represents the first comprehensive investigation relating porosity to the reflectance responses of sandy landscapes. Our findings indicate that the putative dependence of these responses on porosity may be considerably less pronounced than its dependence on other properties such as grain size and shape. Hence, future initiatives for the remote quantification of porosity will likely require reflectance sensors with a high degree of sensitivity.

Porosity estimation by semi-supervised learning with sparsely available labeled samples

Science.gov (United States)

Lima, Luiz Alberto; Görnitz, Nico; Varella, Luiz Eduardo; Vellasco, Marley; Müller, Klaus-Robert; Nakajima, Shinichi

2017-09-01

This paper addresses the porosity estimation problem from seismic impedance volumes and porosity samples located in a small group of exploratory wells. Regression methods, trained on the impedance as inputs and the porosity as output labels, generally suffer from extremely expensive (and hence sparsely available) porosity samples. To optimally make use of the valuable porosity data, a semi-supervised machine learning method was proposed, Transductive Conditional Random Field Regression (TCRFR), showing good performance (Görnitz et al., 2017). TCRFR, however, still requires more labeled data than those usually available, which creates a gap when applying the method to the porosity estimation problem in realistic situations. In this paper, we aim to fill this gap by introducing two graph-based preprocessing techniques, which adapt the original TCRFR for extremely weakly supervised scenarios. Our new method outperforms the previous automatic estimation methods on synthetic data and provides a comparable result to the manual labored, time-consuming geostatistics approach on real data, proving its potential as a practical industrial tool.

Optimization of High Porosity Thermal Barrier Coatings Generated with a Porosity Former

Czech Academy of Sciences Publication Activity Database

Medřický, J.; Curry, N.; Pala, Zdeněk; Vilémová, Monika; Chráska, Tomáš; Johansson, J.; Markocsan, N.

2015-01-01

Roč. 24, č. 4 (2015), s. 622-628 ISSN 1059-9630 R&D Projects: GA ČR GB14-36566G Institutional support: RVO:61389021 Keywords : gas turbine s * high temperature application * porosity of coatings * stabilized zirconia * thermal barrier coatings (TBCs) Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass Impact factor: 1.568, year: 2015

Ultrasonic maps of porosity in aluminum castings

International Nuclear Information System (INIS)

Ghaffari, Bita; Potter, Timothy J.; Mozurkewich, George

2002-01-01

The use of cast aluminum in the automotive industry has grown dramatically in recent years, leading to increased need for quantitative characterization of microporosity. As previously reported in the literature, the attenuation of ultrasound can be used to measure the porosity volume fraction and the mean pore size. An immersion ultrasound system has been built utilizing this technique to scan castings with high spatial resolution. Maps of attenuation are shown to locate areas of varying porosity readily and reliably

The effect of hot water injection on sandstone permeability

DEFF Research Database (Denmark)

Rosenbrand, Esther; Haugwitz, Christian; Jacobsen, Peter Sally Munch

2014-01-01

Seasonal energy storage can be achieved by hot water injection in geothermal sandstone aquifers. We present an analysis of literature data in combination with new short-term flow through permeability experiments in order to address physical and physico-chemical mechanisms that can alter...

Influence of fluvial sandstone architecture on geothermal energy production

NARCIS (Netherlands)

Willems, C.J.L.; Maghami Nick, Hamidreza M.; Weltje, G.J.; Donselaar, M.E.; Bruhn, D.F.

2015-01-01

Fluvial sandstone reservoirs composed of stacked meander belts are considered as potential geothermal resources in the Netherlands. Net-to-gross, orientation and stacking pattern of the channel belts is of major importance for the connectivity between the injection and production well in such

Experimental Study of Cement - Sandstone/Shale - Brine - CO2 Interactions.

Science.gov (United States)

Carroll, Susan A; McNab, Walt W; Torres, Sharon C

2011-11-11

Reactive-transport simulation is a tool that is being used to estimate long-term trapping of CO2, and wellbore and cap rock integrity for geologic CO2 storage. We reacted end member components of a heterolithic sandstone and shale unit that forms the upper section of the In Salah Gas Project carbon storage reservoir in Krechba, Algeria with supercritical CO2, brine, and with/without cement at reservoir conditions to develop experimentally constrained geochemical models for use in reactive transport simulations. We observe marked changes in solution composition when CO2 reacted with cement, sandstone, and shale components at reservoir conditions. The geochemical model for the reaction of sandstone and shale with CO2 and brine is a simple one in which albite, chlorite, illite and carbonate minerals partially dissolve and boehmite, smectite, and amorphous silica precipitate. The geochemical model for the wellbore environment is also fairly simple, in which alkaline cements and rock react with CO2-rich brines to form an Fe containing calcite, amorphous silica, smectite and boehmite or amorphous Al(OH)3. Our research shows that relatively simple geochemical models can describe the dominant reactions that are likely to occur when CO2 is stored in deep saline aquifers sealed with overlying shale cap rocks, as well as the dominant reactions for cement carbonation at the wellbore interface.

Lattice strain measurements on sandstones under load using neutron diffraction

Science.gov (United States)

Frischbutter, A.; Neov, D.; Scheffzük, Ch.; Vrána, M.; Walther, K.

2000-11-01

Neutron diffraction methods (both time-of-flight- and angle-dispersive diffraction) are applied to intracrystalline strain measurements on geological samples undergoing uniaxial increasing compressional load. The experiments were carried out on Cretaceous sandstones from the Elbezone (East Germany), consisting of >95% quartz which are bedded but without crystallographic preferred orientation of quartz. From the stress-strain relation the Young's modulus for our quartz sample was determined to be (72.2±2.9) GPa using results of the neutron time-of-flight method. The influence of different kinds of bedding in sandstones (laminated and convolute bedding) could be determined. We observed differences of factor 2 (convolute bedding) and 3 (laminated bedding) for the elastic stiffness, determined with angle dispersive neutron diffraction (crystallographic strain) and with strain gauges (mechanical strain). The data indicate which geological conditions may influence the stress-strain behaviour of geological materials. The influence of bedding on the stress-strain behaviour of a laminated bedded sandstone was indicated by direct residual stress measurements using neutron time-of-flight diffraction. The measurements were carried out six days after unloading the sample. Residual strain was measured for three positions from the centre to the periphery and within two radial directions of the cylinder. We observed that residual strain changes from extension to compression in a different manner for two perpendicular directions of the bedding plane.

Cathodoluminescence, fluid inclusions and trace element data for the syntaxial quartz cementation in the sandstones of Ora Formation, northern Iraq

DEFF Research Database (Denmark)

Omer, Muhamed Fakhri; Friis, Henrik

2018-01-01

Quartz cements of the quartz arenitic sandstones from the Chalky Nasara and Ora section of the (Devonian-Carboniferous) Ora Formation in northern Iraq have been studied. A combination of Hot-Cathodoluminescence (CL), LA-ICP-MS and fluid inclusions microthermometry revealed three syntaxial quartz......-bedded sandstones than in the6 thickly-bedded sandstones filling most of remaining pore space during mesogenesis. The Q3 was formed during early telogenesis stage fully cementing the sandstones and the fractures were filled by hydrothermal chlorite and sulfides. Significant amount of trace elements Al, Li, Ge...

Nivelstein sandstone, weakly lithified pure silica sands from the Dutch-German border area, intermittently used in architecture for two millennia

Science.gov (United States)

Nijland, Timo G.; Wim Dubelaar, C.

2017-04-01

The current paper provides a concise overview of the geological setting of the Nivelstein sandstone in broad sense, its petrographic and physical characteristics, and its use as natural stone. Miocene pure silica sands occur around Heerlen in the southeastern part of the Dutch province of Limburg and Herzogenrath in adjacent Germany, as well as in the Belgian province of Limburg near Opgrimbie. In Dutch Limburg and in Germany are three large active exploitations, quarrying the sands for industrial purposes. On top of the unconsolidated sands in the Herzogenrath quarry, lithified banks of sandstone occur, known as Nivelstein (or more rarely Herzogenrath) sandstone. This sandstone has been used as dimension stone and ornamental stone since Roman times. In the 11th century the quarry was reopened and after a long period of disuse sandstone blocks were again quarried in the second half of the 19th century. The lithification of the Nivelstein sandstone usually is very weak, with grain to grain contacts and some newly formed quartz rims only. The clay content is extremely low and is restricted to tiny booklets of kaolinite. Despite the weak cementation the Nivelstein sandstone has proved to be very time-resistant building stone that forms a major element in the stone cultural heritage of the Dutch- German border area.

PETROFACIES CHARACTERISTICS OF THE SANDSTONES OF THE UPPER MIOCENELOWER PLIOCENE AGED IN THE ULUMUHSİNE-TATKÖY (KONYA AREA

Directory of Open Access Journals (Sweden)

A. Müjdat ÖZKAN

2000-03-01

Full Text Available In the study area, Upper Miocene-Lower Pliocene aged Ulumuhsine formation, was formed in a shallow, open lake and river environment. The lithologies of this formation are thin-medium bedded, laminated and fossil rich limestone, thin-thick bedded mudstone, thin-thick bedded marl, thin-thick bedded dolomite with stromatolite interbedded limestone, tuffite, chert bands and coal-rich levels. In addition, it includes conglomerates and sandstones of underwater distrubution channels in lacustrine, and channel and bar sediments in stream environments. Red, gray, rarely green colored sandstones are thin-thick bedded, and in some levels well sorting, in some levels proorly sorting. They present sedimentary structures, as graded, herringbone cross-bedding, symmetric ripple-marks, and laminate. Sandstones are named lithic arenite and lithic graywacke and litharenite, feldspathic litharenite and sublithic arenite. These sandstones are rich rock fragments and quartzs, in addition they contain plagioclase, biotite, muskovite, opaque mineral and epidote. Binding materials of sandstones are mainly calcite cements and clay matrix, and iron oxide cement in little amount. From the mineralogical and textural point of view. As a tectonic environment, the main source of sandstones are recycled orogen (thrust, collision and land uplift and recyded lithic fragments.

provenance of sandstone on the western flank of anambra basin

African Journals Online (AJOL)

HP

GLOBAL JOURNAL OF GEOLOGICAL SCIENCES VOL. 14, 2016: 13-21. COPYRIGHT© ... from Fugar locality. The sandstones each classify as quartz arenites and sublitharenites. ... Tectonic movement in the Santonian times resulted in the ...

Porous core-shell carbon fibers derived from lignin and cellulose nanofibrils

KAUST Repository

Xu, Xuezhu

2013-10-01

This letter reports a method to produce lignin and cellulose nanofibrils (CNFs) based porous core-shell carbon fibers via co-electrospinning followed by controlled carbonization. Lignin formed the shell of the fiber while CNF network formed the porous core. Polyacrylonitrile (PAN) was added to the lignin solution to increase its electrospinability. CNFs were surface acetylated and dispersed in silicon oil to obtain a homogenous dispersion for electrospinning the porous core. Hollow lignin fibers were also electrospun using glycerin as the core material. FT-IR measurements confirmed the CNF acetylation. SEM micrographs showed the core-shell and hollow fiber nanostructures before and after carbonization. The novel carbon fibers synthesized in this study exhibited increased surface area and porosity that are promising for many advanced applications. © 2013 Elsevier B.V.

Porous core-shell carbon fibers derived from lignin and cellulose nanofibrils

KAUST Repository

Xu, Xuezhu; Zhou, Jian; Jiang, Long; Lubineau, Gilles; Chen, Ye; Wu, Xiangfa; Piere, Robert

2013-01-01

This letter reports a method to produce lignin and cellulose nanofibrils (CNFs) based porous core-shell carbon fibers via co-electrospinning followed by controlled carbonization. Lignin formed the shell of the fiber while CNF network formed the porous core. Polyacrylonitrile (PAN) was added to the lignin solution to increase its electrospinability. CNFs were surface acetylated and dispersed in silicon oil to obtain a homogenous dispersion for electrospinning the porous core. Hollow lignin fibers were also electrospun using glycerin as the core material. FT-IR measurements confirmed the CNF acetylation. SEM micrographs showed the core-shell and hollow fiber nanostructures before and after carbonization. The novel carbon fibers synthesized in this study exhibited increased surface area and porosity that are promising for many advanced applications. © 2013 Elsevier B.V.

Discussion on several problems on the mineralization of paleo-channel sandstone type uranium deposits

International Nuclear Information System (INIS)

Huang Shijie

1997-01-01

On the basis of comprehensively analyzing paleo-channel sandstone type uranium deposits at home and abroad, the author discusses the division of mineralization types of paleo-channel sandstone type uranium deposits, and analyzes the metallogenic geologic conditions such as regional geologic background, climatic and geomorphological conditions, basement and sedimentary cover, characteristics of paleo-valley and paleo-channel, mineralization features as well as epigenetic metallogenic process. Future prospecting direction is also proposed

Meso and microscopic characterization of deformation bands in porous sandstones: an example on the Paleozoic, Pre- and Sin-rift sequences of the Araripe Basin, Northeast of Brazil; Caracterizacao meso e microscopica de bandas de deformacao em arenitos porosos: um exemplo nas tectonossequencias Paleozoica, Pre- e Sin-rifte da Bacia do Araripe, Nordeste do Brasil

Energy Technology Data Exchange (ETDEWEB)

Araujo Neto, Joao Marculino de; Silva, Fernando Cesar Alves da; Sa, Emanuel Ferraz Jardim de [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil). Programa de Pos-Graduacao em Geodinamica e Geofisica], e-mails: jota_ex2@hotmail.com, fernando@geologia.ufrn.br, emanuel@ccet.ufrn.br

2012-04-15

Deformation bands are narrow tabular volumes developed in porous sandstones. Although these structures are a product of brittle deformation, they may have internally a continuous displacement gradient. When granular cataclasis is the dominant deformation mechanism, the initial properties of their host rocks (i.e., porosity and permeability) can change significantly. The deformation bands in sandstones from the pre- and syn-rift of the Araripe Basin were studied in meso and microscale in order to classify them and to understand the deformation mechanisms involved during their nucleation and development. Their geometric-spatial, kinematic, and rheological criteria allowed establishing relations between the origin of deformation bands and lithification of their host rocks. Additionally, some inferences on their influence to the fluid flow in the reservoir-scale were outlined. Moreover, the study of deformation bands contributed to the understanding of the tectonic evolution of the studied basin. Accordingly, the study of deformation bands can support research on local and regional aspects of the tectonosedimentary evolution of sedimentary basins. (author)

Clay minerals in sandstone uranium deposits: radwaste applications

International Nuclear Information System (INIS)

Brookins, D.G.

1990-01-01

Clay minerals play an important role in the genesis of uranium deposits in sandstones. They incorporate the rate earths (REE), U, Sb, Th, Cs, Rb, Sr, Y, Ba, and even small amounts of chalcophiles. These minerals possess analog elements for many of the radwaste fission products as well as actinides and some actinide daughters. In sandstone uranium deposits, clay minerals are also associated with sulfide minerals, usually pyrite, and organic carbonaceous matter. The primary clay minerals are usually smectites, illites, chlorites and mixed layer varieties. The integrity of these clay minerals is demonstrated by their retention of formational-mineralization ages determined by Rb-Sr geochronologic investigation of the Grants Mineral Belt of the United States. The importance of the clay minerals as analog for parts of the multi-barrier concept in radwaste disposal is their ability to impede water penetration into - and movement of key elements out of uranium rich zones. The clay minerals further sorb and in other ways incorporate into their structures many fission products and actinide analogs from man-made nuclear wastes. 22 refs., 1 fig., 3 tabs

Metallogenic characteristics, model and exploration prospect for the paleo-interlayer-oxidation type sandstone-hosted uranium deposits in China

International Nuclear Information System (INIS)

Huang Jingbai; Li Shengxiang

2007-01-01

In this paper, the paleo-interlayer-oxidation type sandstone-hosted uranium deposits occurred in the Meso-Cenozoic continental basins in China are divided into 3 subtype, they are stratum over lapping buried subtype, structure-uplifting destroy subtype and faulted-folding conserved subtype. The metallogenic characteristics, metallogenic model and exploration prospect for these 3 subtypes uranium deposits are discussed. It is proposed that the paleo-interlayer-oxidation type sandstone-hosted uranium deposits, besides the recent interlayer oxidation type sandstone-hosted uranium deposits, are of great prospecting potential in the Meso-Cenozoic continental basins in China. Therefore, the metallogenic theory of these types uranium deposits should be conscientiously summarized and replenished continuously so as to propel forward the exploration of the sandstone-hosted uranium deposits in China. (authors)

Mueller matrix polarimetry on plasma sprayed thermal barrier coatings for porosity measurement.

Science.gov (United States)

Luo, David A; Barraza, Enrique T; Kudenov, Michael W

2017-12-10

Yttria-stabilized zirconia (YSZ) is the most widely used material for thermal plasma sprayed thermal barrier coatings (TBCs) used to protect gas turbine engine parts in demanding operation environments. The superior material properties of YSZ coatings are related to their internal porosity level. By quantifying the porosity level, tighter control on the spraying process can be achieved to produce reliable coatings. Currently, destructive measurement methods are widely used to measure the porosity level. In this paper, we describe a novel nondestructive approach that is applicable to classify the porosity level of plasma sprayed YSZ TBCs via Mueller matrix polarimetry. A rotating retarder Mueller matrix polarimeter was used to measure the polarization properties of the plasma sprayed YSZ coatings with different porosity levels. From these measurements, it was determined that a sample's measured depolarization ratio is dependent on the sample's surface roughness and porosity level. To this end, we correlate the depolarization ratio with the samples' surface roughness, as measured by a contact profilometer, as well as the total porosity level, in percentage measured using a micrograph and stereological analysis. With the use of this technique, a full-field and rapid measurement of porosity level can be achieved.

Residual CO2 trapping in Indiana limestone.

Science.gov (United States)

El-Maghraby, Rehab M; Blunt, Martin J

2013-01-02

We performed core flooding experiments on Indiana limestone using the porous plate method to measure the amount of trapped CO(2) at a temperature of 50 °C and two pressures: 4.2 and 9 MPa. Brine was mixed with CO(2) for equilibration, then the mixture was circulated through a sacrificial core. Porosity and permeability tests conducted before and after 884 h of continuous core flooding confirmed negligible dissolution. A trapping curve for supercritical (sc)CO(2) in Indiana showing the relationship between the initial and residual CO(2) saturations was measured and compared with that of gaseous CO(2). The results were also compared with scCO(2) trapping in Berea sandstone at the same conditions. A scCO(2) residual trapping end point of 23.7% was observed, indicating slightly less trapping of scCO(2) in Indiana carbonates than in Berea sandstone. There is less trapping for gaseous CO(2) (end point of 18.8%). The system appears to be more water-wet under scCO(2) conditions, which is different from the trend observed in Berea; we hypothesize that this is due to the greater concentration of Ca(2+) in brine at higher pressure. Our work indicates that capillary trapping could contribute to the immobilization of CO(2) in carbonate aquifers.

Preliminary research on finite difference method to solve radon field distribution over sandstone-type uranium ore body

International Nuclear Information System (INIS)

Li Bihong; Shuang Na; Liu Qingcheng

2006-01-01

The principle of finite difference method is introduced, and the radon field distribution over sandstone-type uranium deposit is narrated. The radon field distribution theory equation is established. To solve radon field distribution equation using finite difference algorithm is to provide the value computational method for forward calculation about radon field over sandstone-type uranium mine. Study on 2-D finite difference method on the center of either high anomaly radon fields in view of the character of radon field over sandstone-type uranium provide an algorithm for further research. (authors)

CHARACTERIZATION OF SANDSTONE RESERVOIRS FOR ENHANCED OIL RECOVERY: THE PERMIAN UPPER MINNELUSA FORMATION, POWDER RIVER BASIN, WYOMING.

Science.gov (United States)

Schenk, C.J.; Schmoker, J.W.; Scheffler, J.M.

1986-01-01

Upper Minnelusa sandstones form a complex group of reservoirs because of variations in regional setting, sedimentology, and diagenetic alteration. Structural lineaments separate the reservoirs into northern and southern zones. Production in the north is from a single pay sand, and in the south from multi-pay sands due to differential erosion on top of the Upper Minnelusa. The intercalation of eolian dune, interdune, and sabkha sandstones with marine sandstones, carbonates, and anhydrites results in significant reservoir heterogeneity. Diagenetic alterations further enhance heterogeneity, because the degree of cementation and dissolution is partly facies-related.

Tailoring the porosity of hierarchical zeolites by carbon-templating

DEFF Research Database (Denmark)

Zhu, Kake; Egeblad, Kresten; Christensen, Claus H.

2008-01-01

We report the synthesis and characterization of a series of hierarchical porous zeolite single crystal materials with a range of porosities made available by carbon-templating using differently-sized carbon particles as templates for the additional non-micropore porosity. The materials were...

Uranium-series disequilibria as a means to study recent migration of uranium in a sandstone-hosted uranium deposit, NW China

International Nuclear Information System (INIS)

Min Maozhong; Peng Xinjian; Wang Jinping; Osmond, J.K.

2005-01-01

Uranium concentration and alpha specific activities of uranium decay series nuclides 234 U, 238 U, 230 Th, 232 Th and 226 Ra were measured for 16 oxidized host sandstone samples, 36 oxic-anoxic (mineralized) sandstone samples and three unaltered primary sandstone samples collected from the Shihongtan deposit. The results show that most of the ores and host sandstones have close to secular equilibrium alpha activity ratios for 234 U/ 238 U, 230 Th/ 238 U, 230 Th/ 234 U and 226 Ra/ 230 Th, indicating that intensive groundwater-rock/ore interaction and uranium migration have not taken place in the deposit during the last 1.0 Ma. However, some of the old uranium ore bodies have locally undergone leaching in the oxidizing environment during the past 300 ka to 1.0 Ma or to the present, and a number of new U ore bodies have grown in the oxic-anoxic transition (mineralized) subzone during the past 1.0 Ma. Locally, uranium leaching has taken place during the past 300 ka to 1.0 Ma, and perhaps is still going on now in some sandstones of the oxidizing subzone. However, uranium accumulation has locally occurred in some sandstones of the oxidizing environment during the past 1 ka to 1.0 Ma, which may be attributed to adsorption of U(VI) by clays contained in oxidized sandstones. A recent accumulation of uranium has locally taken place within the unaltered sandstones of the primary subzone close to the oxic-anoxic transition environment during the past 300 ka to 1.0 Ma. Results from the present study also indicate that uranium-series disequilibrium is an important tool to trace recent migration of uranium occurring in sandstone-hosted U deposits during the past 1.0 Ma and to distinguish the oxidation-reduction boundary

PmaCO{sub 2} Project: Porosity and CO{sub 2} Trapping Mechanisms The Utrillas Formation in SD-1 borehole (Tejada - Burgos): Porosity and Porous Media Modelling; PROYECTO PmaCO{sub 2}: Porosidad y Mecanismos de Atrapamiento de CO{sub 2} La Formacion Utrillas en el Sondeo SD-1 (Tejada - Burgos): Porosidad y Modelizacion del Sistema Poroso

Energy Technology Data Exchange (ETDEWEB)

Campos, R.; Barrios, I.; Gonzalez, A. M.

2013-03-01

The aim of PmaCO{sub 2} project, supported by the Secretary of State and Research MINECO (CGL2011-24768) is to increase the knowledge of the microstructure of porous storage formations and thus contribute to the viability of CO{sub 2} sequestration in geological formations. The microporous structure plays an important role not only in the prevalence of a particular trapping mechanism, but also on the amount of CO{sub 2} immobilized. Utrillas facies are investigated in this project as representatives of a deep saline aquifer storage. This publication is a summary of the work done in the first year of the project. We present a study on microstructure of sandstones Utrillas, sampled in borehole, by applying the mercury intrusion porosimetry technique for the experimental determination of porosity and associated parameters. The porous medium was modeled with the PoreCor simulation code based in intrusion-extrusion curves. (Author) 78 refs.

Integrated design of castings: effect of porosity on mechanical performance

International Nuclear Information System (INIS)

Hardin, R A; Beckermann, C

2012-01-01

Porosity can significantly reduce the strength and durability of castings in service. An integrated design approach has been developed where casting simulation is combined with mechanical performance simulations. Predictions of the porosity distribution from the casting process simulation are transferred to and used in stress and fatigue life simulations. Thus, the effect of casting quality on service performance can be evaluated. Results of a study are presented where the measured porosity distribution in cast steel specimens is transferred to an elasto-plastic finite-element stress analysis model. Methods are developed to locally reduce the mechanical properties according to the porosity present, without having to resolve individual pores. Plastic deformation is modeled using porous metal plasticity theory. The predictions are compared to tensile measurements performed on the specimens. The complex deformations and the reductions in the ductility of the specimens due to porosity are predicted well. The predicted stresses are transferred to a fatigue analysis code that takes the porosity distribution into account as well. The measured and predicted fatigue lives are also in good agreement. Finally, the results of a case study are presented that illustrate the utility of the present integrated approach in optimizing the design of a steel casting.

Porosity-dependent fractal nature of the porous silicon surface

Energy Technology Data Exchange (ETDEWEB)

Rahmani, N.; Dariani, R. S., E-mail: dariani@alzahra.ac.ir [Department of Physics, Alzahra University, Tehran, 1993893973 (Iran, Islamic Republic of)

2015-07-15

Porous silicon films with porosity ranging from 42% to 77% were fabricated by electrochemical anodization under different current density. We used atomic force microscopy and dynamic scaling theory for deriving the surface roughness profile and processing the topography of the porous silicon layers, respectively. We first compared the topography of bare silicon surface with porous silicon and then studied the effect of the porosity of porous silicon films on their scaling behavior by using their self-affinity nature. Our work demonstrated that silicon compared to the porous silicon films has the highest Hurst parameter, indicating that the formation of porous layer due to the anodization etching of silicon surface leads to an increase of its roughness. Fractal analysis revealed that the evolution of the nanocrystallites’ fractal dimension along with porosity. Also, we found that both interface width and Hurst parameter are affected by the increase of porosity.

Prospect analysis for sandstone-type uranium mineralization in the northern margin of Qaidam basin

International Nuclear Information System (INIS)

Liu Lin; Song Xiansheng; Feng Wei; Song Zhe; Li Wei

2010-01-01

Affected by the regional geological structural evolution, a set of sedimentary structure, i.e. the construction of coal-bearing classic rocks which is in favor of the sandstone-type uranium mineralization has deposited in the northern margin of Qaidam Basin since Meso-Cenozoic. A NWW thrust nappe tectonic belt, i.e. the ancient tectonic belt which is the basis for the development of ancient interlayer oxidation zone formed by the tectonic reverse in late Jurassic and Cretaceous. The Mid and late Jurassic layer was buried by the weak extension in Paleogene and the depression in early Neogene. The extrusion reversal from late Neogene to Quaternary made the basin into the development era of the modern interlayer oxidation zone. It can be concluded that the layer of the northern margin of Qaidam Basin has the premise for the formation of sandstone-type uranium ore. Based on the analysis of the characteristics of the thrust belt, the structure of the purpose layer, the sand body, the hydrogeology, the interlayer oxidation zone and uranium mineralization, the results indicated that the ancient interlayer oxidation zone is the prospecting type of sandstone-type uranium ore. Beidatan and the east of Yuqia are the favorable prospective area of sandstone-type uranium mineralization. (authors)

The migration of uranium through sandstone

International Nuclear Information System (INIS)

Bennett, D.G.; Read, D.; Lawless, T.A.; Sims, R.J.

1992-01-01

Three column experiments are described in which the migration of uranium through Clashach Sandstone was studied. A priori predictions of uranium migration in the experiments were made using an equilibrium chemical transport model. The experimental results showed that, even under oxidising conditions, the migration of uranium is strongly retarded owing to the affinity of uranium for mineral surfaces. For the relatively simple chemical system investigated, the chemical transport model was successful in predicting the migration of uranium and its distribution along the column. (author)

Model Compaction Equation

African Journals Online (AJOL)

The currently proposed model compaction equation was derived from data sourced from the. Niger Delta and it relates porosity to depth for sandstones under hydrostatic pressure condition. The equation is useful in predicting porosity and compaction trend in hydrostatic sands of the. Niger Delta. GEOLOGICAL SETTING OF ...

Reviews on the metallogenic and geological features of sandstone-type uranium deposits in Japan

International Nuclear Information System (INIS)

Pei Chengkai; Huang Xianfang; Zhang Baoju

2006-01-01

Regional geologic settings of sandstone-type uranium deposits in Japan are firstly analyzed. The regional tectonic evolution characteristics of 'Green tuff region' and 'Non green tuff region' and their relationship with uranium mineralization are elaborated in depth. Based on those mentioned above, the uranium sources of sandstone-type uranium deposits in Japan are discussed deeply and the most favorable uranium sources are considered to come from the basement and the surrounding granites. Their intrusive epochs range from Later Cretaceous to Palaeogene (about 60 to 70 Ma ago). The characteristics of ore-bearing host rocks, matter compositions of the deposits, ore formation enrichment factors, the hydrogeologic conditions and so on are described by taking Ningyo-Toge and Tono deposits as examples. Finally, the prospecting measures for the palaeo-channel sandstone-type uranium deposits (basal type) are reviewed. (authors)

Petrographic characteristic of the sandstones of the upper paleocene-middle eocene aged in the Yildizli-Aydinkent (Ereğli-Konya area

Directory of Open Access Journals (Sweden)

A. Müjdat Özkan

2002-03-01

Full Text Available In the study area, Upper Paleocene - Middle Eocene aged Halkapınar formation, was formed in a shallow and deep marine environment. The lithologies of this formation are medium - thick bedded conglomerate, thin - thick bedded sandstone, thin - very thick bedded shale, thin - medium bedded marl with chert nodules and bands. In addition olistolithes of ophiolitic melange are found at the top of the sandstones, which includes basalt interbands. Yellowish gray, greenish gray, beige, gray colored sandstones include some sedimentary structures, namely ripple - marks, graded bedding, laminate, convolute lamination, current ripple, tool marks. Constituents of the sandstones are quartz, plagioclase, sanidine, orthoclase, fragments of sedimentary and methamorphic rocks, biotite, muscovite, opaque mineral and glauconite. The sandstones, which are not matured in terms of mineralogy and texture, are mainly cemented by calcite, clay matrix and minor iron oxide and glauconite matrix. The sandstones are named lithic arenite, lithic graywacke, feldspathic litharenite and litharenite.

Insights into the dolomitization process and porosity modification in sucrosic dolostones, Avon Park Formation (Middle Eocene), East-Central Florida, U.S.A.

KAUST Repository

Maliva,, Robert G.

2011-03-01

The Avon Park Formation (middle Eocene) in central Florida, U.S.A., contains shallow-water carbonates that have been replaced by dolomite to varying degrees, ranging from partially replaced limestones, to highly porous sucrosic dolostones, to, less commonly, low-porosity dense dolostones. The relationships between dolomitization and porosity and permeability were studied focusing on three 305-m-long cores taken in the City of Daytona Beach. Stable-isotope data from pure dolostones (mean δ 18O = +3.91% V-PDB) indicate dolomite precipitation in Eocene penesaline pore waters, which would be expected to have been at or above saturation with respect to calcite. Nuclear magnetic log-derived porosity and permeability data indicate that dolomitization did not materially change total porosity values at the bed and formation scale, but did result in a general increase in pore size and an associated substantial increase in permeability compared to limestone precursors. Dolomitization differentially affects the porosity and permeability of carbonate strata on the scale of individual crystals, beds, and formations. At the crystal scale, dolomitization occurs in a volume-for-volume manner in which the space occupied by the former porous calcium carbonate is replaced by a solid dolomite crystal with an associated reduction in porosity. Dolomite crystal precipitation was principally responsible for calcite dissolution both at the actual site of dolomite crystal growth and in the adjoining rock mass. Carbonate is passively scavenged from the formation, which results in no significant porosity change at the formation scale. Moldic pores after allochems formed mainly in beds that experienced high degrees of dolomitization, which demonstrates the intimate association of the dolomitization process with carbonate dissolution. The model of force of crystallization-controlled replacement provides a plausible explanation for key observations concerning the dolomitization process in the

Insights into the dolomitization process and porosity modification in sucrosic dolostones, Avon Park Formation (Middle Eocene), East-Central Florida, U.S.A.

KAUST Repository

Maliva,, Robert G.; Budd, David A.; Clayton, Edward A.; Missimer, Thomas M.; Dickson, John Anthony D

2011-01-01

The Avon Park Formation (middle Eocene) in central Florida, U.S.A., contains shallow-water carbonates that have been replaced by dolomite to varying degrees, ranging from partially replaced limestones, to highly porous sucrosic dolostones, to, less commonly, low-porosity dense dolostones. The relationships between dolomitization and porosity and permeability were studied focusing on three 305-m-long cores taken in the City of Daytona Beach. Stable-isotope data from pure dolostones (mean δ 18O = +3.91% V-PDB) indicate dolomite precipitation in Eocene penesaline pore waters, which would be expected to have been at or above saturation with respect to calcite. Nuclear magnetic log-derived porosity and permeability data indicate that dolomitization did not materially change total porosity values at the bed and formation scale, but did result in a general increase in pore size and an associated substantial increase in permeability compared to limestone precursors. Dolomitization differentially affects the porosity and permeability of carbonate strata on the scale of individual crystals, beds, and formations. At the crystal scale, dolomitization occurs in a volume-for-volume manner in which the space occupied by the former porous calcium carbonate is replaced by a solid dolomite crystal with an associated reduction in porosity. Dolomite crystal precipitation was principally responsible for calcite dissolution both at the actual site of dolomite crystal growth and in the adjoining rock mass. Carbonate is passively scavenged from the formation, which results in no significant porosity change at the formation scale. Moldic pores after allochems formed mainly in beds that experienced high degrees of dolomitization, which demonstrates the intimate association of the dolomitization process with carbonate dissolution. The model of force of crystallization-controlled replacement provides a plausible explanation for key observations concerning the dolomitization process in the

Ultrasonic Characterization of Water Saturated Double Porosity Media

Science.gov (United States)

Bai, Ruonan; Tinel, Alain; Alem, Abdellah; Franklin, Hervé; Wang, Huaqing

Wave propagation through a multilayered structure consisting of a water saturated double porosity medium in an aluminum rectangular box immersed in water is studied. By assuming a plane incident wave from water onto the structure, the reflection and transmission coefficients are derived by application of the boundary conditions at each interface. Numerical computations are done for two particular double porosity media, ROBU® and Tobermorite 11 Å, that are assumed to obey Berryman's extension of Biot's theory [Berryman 1995, 2000]. The influence of the thickness of double porosity medium is investigated. To compare experiments to computations, two comparison coefficients Cnum and Cexp are introduced. The theoretical one Cnum is defined as the ratio of the transmission coefficient of the structure to the transmission coefficient of the box filled exclusively with water. The experimental comparison coefficient Cexp is defined as the ratio of the Fourier transforms of the transmitted signals by the box filled with the double porous medium to that of the transmitted signals by the box filled with water. A method of minimization based on a gradient descent algorithm is used to optimize some of the parameters of the double porosity media such as the bulk moduli.

Mineralogical, chemical, organic and microbial properties of subsurface soil cores from Mars Desert Research Station (Utah, USA): Phyllosilicate and sulfate analogues to Mars mission landing sites

NARCIS (Netherlands)

Stoker, C.R.; Clarke, J.; Oliveira Lebre Direito, M.S.; Martin, K.; Zavaleta, J.; Blake, D.; Foing, B.H.

2011-01-01

We collected and analysed soil cores from four geologic units surrounding Mars Desert Research Station (MDRS) Utah, USA, including Mancos Shale, Dakota Sandstone, Morrison formation (Brushy Basin member) and Summerville formation. The area is an important geochemical and morphological analogue to

Tertiary lithofacies and paleo-geographic framework and interlayer oxidation zone sandstone uranium deposits in Longjiang-Zhaozhou area

International Nuclear Information System (INIS)

Zhang Zhenqiang

2003-01-01

The main points of views for the experiment are: (1) Yi'an formation is mainly composed of limnetic facies of siltstone and fine sandstone, due to weak surface water, limited sedimentation and simple material source; (2) strengthened surface water and enormous material brought from north and west-north and enlarged sedimentation from north to south, the major deposition during Da'an period are channel facies of conglomerate and river bed facies of sandstone; (3) stronger surface water during Taikang period, led alluvial-flood plain facies brown-yellow conglomerate to develop along western margin of the basin, the channel facies of conglomerate and river bed facies of grey-green sandstone, pelitic siltstone were widely formed southward and eastward; (4) according to the lithofacies criterion for in-situ leachable sandstone uranium ore, Taikang formation is an ideal horizon, river bed facies is suitable for interlayer oxidation type uranium deposit. (author)

Mechanical Behavior of Low Porosity Carbonate Rock: From Brittle Creep to Ductile Creep.

Science.gov (United States)

Nicolas, A.; Fortin, J.; Gueguen, Y.

2014-12-01

Mechanical compaction and associated porosity reduction play an important role in the diagenesis of porous rocks. They may also affect reservoir rocks during hydrocarbon production, as the pore pressure field is modified. This inelastic compaction can lead to subsidence, cause casing failure, trigger earthquake, or change the fluid transport properties. In addition, inelastic deformation can be time - dependent. In particular, brittle creep phenomena have been deeply investigated since the 90s, especially in sandstones. However knowledge of carbonates behavior is still insufficient. In this study, we focus on the mechanical behavior of a 14.7% porosity white Tavel (France) carbonate rock (>98% calcite). The samples were deformed in a triaxial cell at effective confining pressures ranging from 0 MPa to 85 MPa at room temperature and 70°C. Experiments were carried under dry and water saturated conditions in order to explore the role played by the pore fluids. Two types of experiments have been carried out: (1) a first series in order to investigate the rupture envelopes, and (2) a second series with creep experiments. During the experiments, elastic wave velocities (P and S) were measured to infer crack density evolution. Permeability was also measured during creep experiments. Our results show two different mechanical behaviors: (1) brittle behavior is observed at low confining pressures, whereas (2) ductile behavior is observed at higher confining pressures. During creep experiments, these two behaviors have a different signature in term of elastic wave velocities and permeability changes, due to two different mechanisms: development of micro-cracks at low confining pressures and competition between cracks and microplasticity at high confining pressure. The attached figure is a summary of 20 triaxial experiments performed on Tavel limestone under different conditions. Stress states C',C* and C*' and brittle strength are shown in the P-Q space: (a) 20°C and dry

La porosidad en las areniscas triásicas (Rama Aragonesa de la Cordillera Ibérica

Directory of Open Access Journals (Sweden)

Arribas, J.

1984-12-01

Full Text Available Triassic sandstone's porosity (Buntsandstein and Muschelkalk facies from the Aragonesa Branch of the Iberian Range are studied, firstly at the sediment primary porosity calculation and secondly the porosity-reducing processes are analyzed. Processes creating secondary sandstone porosity can be established (dissolution and fracturing by the textural and genetic caracterization of the sandstone's voids. The dissolution of potassium feldspar, carbonate cement and barite cement, is related with meteoric pore-water flow alloys to intramesozoic unconformities, Fracturing porosity is related to Iberian Range tertiary structuration. Finally, we concluded that the amount of the sandstone's secondary porosity depends mainly on the original composition of the sediments and also on the geochemical sedimentary environments that control the first diagenetic stages (eodiagenesis, This fact manifests itself in the amount and types of variating porosities along the stratigraphic section.

Se estudia la porosidad en las areniscas triásicas (facies Buntsandstein y Muschelkalk de la Rama Aragonesa de la Cordillera Ibérica, partiendo del cálculo estimativo de la porosidad primaria del sedimento, para posteriormente analizar los distintos procesos diagenéticos que han intervenido en su destrucción (compactación mecánica, compactación química y cementación. La caracterización textural y genética de los poros en dichas areniscas permite establecer la existencia de procesos generadores de porosidad secundaria (disolución y fractura. La disolución del feldespato potásico, cemento carbonático y de baritina se relaciona con flujos de aguas meteóricas ligadas a discordancias intramesozoicas, mientras que la porosidad de fractura se asocia a la estructuración terciaria de la Cordillera Ibérica. Por ú1timo se concluye que la cantidad de porosidad secundaria en las areniscas estudiadas depende fundamentalmente de la composición original de los dep

The Effect of Volumetric Porosity on Roughness Element Drag

Science.gov (United States)

Gillies, John; Nickling, William; Nikolich, George; Etyemezian, Vicken

2016-04-01

Much attention has been given to understanding how the porosity of two dimensional structures affects the drag force exerted by boundary-layer flow on these flow obstructions. Porous structures such as wind breaks and fences are typically used to control the sedimentation of sand and snow particles or create micro-habitats in their lee. Vegetation in drylands also exerts control on sediment transport by wind due to aerodynamic effects and interaction with particles in transport. Recent research has also demonstrated that large spatial arrays of solid three dimensional roughness elements can be used to reduce sand transport to specified targets for control of wind erosion through the effect of drag partitioning and interaction of the moving sand with the large (>0.3 m high) roughness elements, but porous elements may improve the effectiveness of this approach. A thorough understanding of the role porosity plays in affecting the drag force on three-dimensional forms is lacking. To provide basic understanding of the relationship between the porosity of roughness elements and the force of drag exerted on them by fluid flow, we undertook a wind tunnel study that systematically altered the porosity of roughness elements of defined geometry (cubes, rectangular cylinders, and round cylinders) and measured the associated change in the drag force on the elements under similar Reynolds number conditions. The elements tested were of four basic forms: 1) same sized cubes with tubes of known diameter milled through them creating three volumetric porosity values and increasing connectivity between the tubes, 2) cubes and rectangular cylinders constructed of brass screen that nested within each other, and 3) round cylinders constructed of brass screen that nested within each other. The two-dimensional porosity, defined as the ratio of total surface area of the empty space to the solid surface area of the side of the element presented to the fluid flow was conserved at 0.519 for

Mathematical modeling of porosity formation in die cast A356 wheels

International Nuclear Information System (INIS)

Maijer, D.; Cockcroft, S.L.; Wells, M.A.; Luciuk, T.; Hermesmann, C.

2000-01-01

In an effort to leverage recent advances in modeling and process simulation tools, a mathematical model has been developed to predict porosity formation in die cast A356 wheels as part of a collaborative research agreement between researchers at the University of British Columbia and Canadian Autoparts Toyota Incorporated. The heat transfer model represents a three-dimensional, 30 o , slice of the wheel and die and is based on the commercial finite element code ABAQUS. Extensive temperature measurements in the die and in the wheel taken over several cycles in the casting process were used to fine tune and validate the model. Initial work on predicting porosity formation has focused on using the Niyama parameter as a measure of the probability of porosity. To date Niyama porosity predictions agree well with plant experience and show promise for reducing losses associated with porosity. (author)

Porosity prediction from seismic inversion, Lavrans Field, Halten Terrace

Energy Technology Data Exchange (ETDEWEB)

Dolberg, David M.

1998-12-31

This presentation relates to porosity prediction from seismic inversion. The porosity prediction concerns the Lavrans Field of the Halten Terrace on the Norwegian continental shelf. The main themes discussed here cover seismic inversion, rock physics, statistical analysis - verification of well trends, upscaling/sculpting, and implementation. 2 refs., 6 figs.

Evaluation of porosity in Al alloy die castings

Directory of Open Access Journals (Sweden)

M. Říhová

2012-01-01

Full Text Available Mechanical properties of an Al-alloy die casting depend significantly on its structural properties. Porosity in Al-alloy castings is one of the most frequent causes of waste castings. Gas pores are responsible for impaired mechanical-technological properties of cast materials. On the basis of a complex evaluation of experiments conducted on AlSi9Cu3 alloy samples taken from the upper engine block which was die- cast with and without local squeeze casting it can be said that castings manufactured without squeeze casting exhibit maximum porosity in the longitudinal section. The area without local squeeze casting exhibits a certain reduction in mechanical properties and porosity increased to as much as 5%. However, this still meets the norms set by SKODA AUTO a.s.

Particle porosity at plasma are spraying of metals

International Nuclear Information System (INIS)

Petrunichev, V.A.; Koroleva, E.B.; Pushilin, N.P.

1985-01-01

Quantitative dependences of porosity and character of pore distribution in particles of different materials on particle size and composition of atmosphere in a working chamber are studied experimentally as applied to the process of plasma wire sputtering. Wires 1.2 mm in diameter made of tungsten, molybdenum, Kh20N80 alloy, and zirconium served as sputtering materials. It is shown that pore size and character of their distribution in particles of powders obtained by the method of plasma wire sputtering are dependent on sizes of forming particles and determined by conditions of their cooling. Intensive porosity formation is characteristic of wire sputtering in argon plasma with nitrogen additions, but there are critical values of nitrogen concentration in plasma, above which intensive porosity formation in forming particles stops

Aspects of the sedimentology of some uranium-bearing sandstones in the Beaufort West area, Cape Province

International Nuclear Information System (INIS)

Cole, D.I.

1980-01-01

The sedimentology of some uranium-bearing sandstones from the Beaufort Group in the Beaufort West area was studied by use of some 116 vertical profiles measured across and adjacent to 14 mineralized deposits. The vertical profiles consist of 91 field sections and 25 borehole logs. The sandstones are usually multistorey and alternate with a mudstone and/or siltstone succession. The vertical profiles basically consist of a succession of facies. Some 19 facies were recognised within the sandstones on the basis of texture and sedimentary structure. The facies transitions within the sandstone sequence were subjected to a one-step Markov chain analysis. The cumulative thickness of uranium mineralization for each sedimentary facies within the sandstone sequence was measured. Some 99 per cent of the total cumulative thickness occurs within the coarser-grained facies (grain sizes in excess of very fine), which suggests that permeability was an important control on the mineralization. The coarser-grained facies, which mostly represent lower point bar or channel bar deposits near the base of each storey, probably acted as suitable aquifers for the transport of uraniferous solutions. Irregularities in the base of each storey may have interrupted the flow of these solutions and allowed sufficient time for precipitation of the uranium. Carbonaceous debris is frequently associated with the mineralized deposits and most likely acted as an indirect reductant for this precipitation. Mineralization decreases upwards in the sandstone sequence and some 40 per cent of the total cumulative thickness is restricted to the initial storey. The horizontally bedded facies contain a high proportion of the total cumulative thickness of mineralization (45 per cent) and this again may be related to a more abundant content of carbonaceous debris

National uranium resource evaluation. Geology and recognition criteria for sandstone uranium deposits of the salt wash type, Colorado Plateau Province. Final report

International Nuclear Information System (INIS)

Thamm, J.K.; Kovschak, A.A. Jr.; Adams, S.S.

1981-01-01

The uranium-vanadium deposits of the Salt Wash Member of the Morrison Formation in the Colorado Plateau are similar to sandstone uranium deposits elsewhere in the USA. The differences between Salt Wash deposits and other sandstone uranium deposits are also significant. The Salt Wash deposits are unique among sandstone deposits in that they are dominantly vanadium deposits with accessory uranium. The Salt Wash ores generally occur entirely within reduced sandstone, without adjacent tongues of oxidized sandstone. They are more like the deposits of Grants, which similarly occur in reduced sandstones. Recent studies of the Grants deposits have identified alteration assemblages which are asymmetrically distributed about the deposits and provide a basis for a genetic model for those deposits. The alteration types recognized by Shawe in the Slick Rock district may provide similar constraints on ore formation when expanded to broader areas and more complete chemical analyses

Systematic logging utilizing a log sheet designed for drill core descriptions. An example in uranium exploration activities

International Nuclear Information System (INIS)

Sasao, Eiji; Tsuruta, Tadahiko; Iida, Yoshimasa

2000-01-01

We describe the log sheets used during uranium exploration activities for unconformity-related uranium deposits by JNC. The purpose of using the logging sheets is to standardize the objects which all geologists must observe and for data quality assurance. The log sheets are a three-part set describing basement lithology, sandstone lithology and geotechnics. We devised our own log sheets to describe both the sandstone and the underlying basement rock when we started exploration in Athabasca Basin, Canada. We modified the sheets to gain a better understanding of the geological features related to uranium mineralization, and made final improvements to satisfy required quality based on the criteria of descriptive objects and accuracy. Use of the log sheets resulted in effective performance of core logging and improvement in the display of data. (author)

Properties of Bulk Sintered Silver As a Function of Porosity

Energy Technology Data Exchange (ETDEWEB)