WorldWideScience

Sample records for sandia microelectronics development

  1. Micromachined sensor and actuator research at Sandia`s Microelectronics Development Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Smith, J.H.

    1996-11-01

    An overview of the surface micromachining program at the Microelectronics Development Laboratory of Sandia National Laboratories is presented. Development efforts are underway for a variety of surface micromachined sensors and actuators for both defense and commercial applications. A technology that embeds micromechanical devices below the surface of the wafer prior to microelectronics fabrication has been developed for integrating microelectronics with surface-micromachined micromechanical devices. The application of chemical-mechanical polishing to increase the manufacturability of micromechanical devices is also presented.

  2. Microelectronics at Sandia Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Spencer, W.J.; Gregory, B.L.; Franzak, E.G.; Hood, J.A.

    1975-12-31

    The microelectronics capability at Sandia Laboratories spans the complete range of component activity from initial design to final assembly into subsystems and systems. Highly reliable, radiation-tolerant devices and integrated circuits can be designed, fabricated, and incorporated into printed circuit assemblies or into thick- or thin-film hybrid microcircuits. Sandia has an experienced staff, exceptional facilities and aggressive on-going programs in all these areas. The authors can marshall a broad range of skills and capabilities to attack and solve problems in design, fabrication, assembly, or production. Key facilities, programs, and capabilities in the Sandia microelectronics effort are discussed in more detail in this booklet.

  3. Results of external review Sandia microelectronics and microsystems program (September 2004).

    Energy Technology Data Exchange (ETDEWEB)

    Peercy, Paul S. (University of Wisconsin-Madison, Madision, WI); Myers, David R.

    2005-08-01

    The US Department of Energy requires a periodic assessment of the Microsystems Program at Sandia National Laboratories. An external review of this program is held approximately every 18 months to 24 months. The report from the External Review Panel serves as the basis for Sandia's ''self assessment'' and is a specific deliverable of the governance contract between Lockheed Martin and the Department of Energy. The External Review of Microelectronics and Microsystems for Fiscal Year 2004 was held September 27-29, 2004 at Sandia National Laboratories, Albuquerque, NM. The external review panel consisted of experts in the fields of microelectronics, photonics and microsystems from universities, industry and other Government agencies. A complete list of the panel members is included as Appendix A of the attached report. The review assessed four areas: relevance to national needs and agency mission; quality of science, technology and engineering; performance in the operation of a major facility; and program performance management and planning. Relevance to national needs and agency mission was rated as ''outstanding''. The quality of science, technology, and engineering was rated as ''outstanding''. Operation of a major facility was rated as ''outstanding'', and the category of program performance, management, and planning was rated as ''outstanding''. Sandia's Microsystems Program thus received an overall rating of ''outstanding'' [the highest possible rating].

  4. Development of the Sandia Cooler.

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Terry Alan; Koplow, Jeffrey P.; Staats, Wayne Lawrence,; Curgus, Dita Brigitte; Leick, Michael Thomas.; Matthew, Ned Daniel; Zimmerman, Mark D.; Arienti, Marco; Gharagozloo, Patricia E.; Hecht, Ethan S.; Spencer, Nathan A.; Vanness, Justin William.; Gorman, Ryan

    2013-12-01

    This report describes an FY13 effort to develop the latest version of the Sandia Cooler, a breakthrough technology for air-cooled heat exchangers that was developed at Sandia National Laboratories. The project was focused on fabrication, assembly and demonstration of ten prototype systems for the cooling of high power density electronics, specifically high performance desktop computers (CPUs). In addition, computational simulation and experimentation was carried out to fully understand the performance characteristics of each of the key design aspects. This work culminated in a parameter and scaling study that now provides a design framework, including a number of design and analysis tools, for Sandia Cooler development for applications beyond CPU cooling.

  5. Results of external review Sandia National Laboratories microelectronics and photonics program (October 2002).

    Energy Technology Data Exchange (ETDEWEB)

    Peercy, Paul S. (University of Wisconsin, Madison, WI); Myers, David R.

    2003-10-01

    The US Department of Energy requires a periodic 'self assessment' of Sandia's Microsystems Program. An external panel review of this program is held approximately every 18 months, and the report from the external review panel serves as the basis for the DOE 'self assessment.' The review for this fiscal year was held on September 30-October 1, 2002 at Sandia National Laboratories, Albuquerque, NM. The panel was comprised of experts in the fields of microelectronics, photonics and microsystems from universities, industry and other Government agencies. A complete list of the panel members is shown as Appendix A to the attached report. The review assesses four areas: relevance to national needs and agency mission; quality of science technology and engineering; performance in the operation of a major facility; and program performance management and planning. Relevance to national needs and agency mission was rated as 'outstanding.' The quality of science, technology, and engineering was rated as 'outstanding.' Operation of a major facility was noted as 'outstanding,' while the category of program performance, management, and planning was rated as 'outstanding.' Sandia's Microsystems Program received an overall rating of 'outstanding' [the highest possible rating]. The attached report was prepared by the panel in a format requested by Sandia to conform with the performance criteria for the DOE self assessment.

  6. Developments in microelectronics: Past and future

    Science.gov (United States)

    Zhijian, L.

    1985-04-01

    The evolution of microelectronics in China is reviewed. Current developments and fracture trends seen as characteristic of the technology are discussed and some suggestions are offered as to the advancement of microelectronics in China.

  7. Pathfinder radar development at Sandia National Laboratories

    Science.gov (United States)

    Castillo, Steven

    2016-05-01

    Since the invention of Synthetic Aperture Radar imaging in the 1950's, users or potential users have sought to exploit SAR imagery for a variety of applications including the earth sciences and defense. At Sandia Laboratories, SAR Research and Development and associated defense applications grew out of the nuclear weapons program in the 1980's and over the years has become a highly viable ISR sensor for a variety of tactical applications. Sandia SAR systems excel where real-­-time, high-­-resolution, all-­-weather, day or night surveillance is required for developing situational awareness. This presentation will discuss the various aspects of Sandia's airborne ISR capability with respect to issues related to current operational success as well as the future direction of the capability as Sandia seeks to improve the SAR capability it delivers into multiple mission scenarios. Issues discussed include fundamental radar capabilities, advanced exploitation techniques and human-­-computer interface (HMI) challenges that are part of the advances required to maintain Sandia's ability to continue to support ever changing and demanding mission challenges.

  8. Sandia QIS Capabilities.

    Energy Technology Data Exchange (ETDEWEB)

    Muller, Richard P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-07-01

    Sandia National Laboratories has developed a broad set of capabilities in quantum information science (QIS), including elements of quantum computing, quantum communications, and quantum sensing. The Sandia QIS program is built atop unique DOE investments at the laboratories, including the MESA microelectronics fabrication facility, the Center for Integrated Nanotechnologies (CINT) facilities (joint with LANL), the Ion Beam Laboratory, and ASC High Performance Computing (HPC) facilities. Sandia has invested $75 M of LDRD funding over 12 years to develop unique, differentiating capabilities that leverage these DOE infrastructure investments.

  9. ByLaws for the Governance of the Sandia National Laboratories Sandia Postdoctoral Development (SPD) Association.

    Energy Technology Data Exchange (ETDEWEB)

    McBride, Amber Alane Fisher; McBride, Amber Alane Fisher; Rodgers, Theron; Dong, Wen; Juan, Pierre-Alexandre; Barkholtz, Heather; Alley, William Morgan; Wolk, Benjamin Matthew; Vane, Zachary Phillips; Priye, Aashish; Ball, Cameron Scott

    2017-03-01

    The purpose of this document is to define the rules of governance for the Sandia Postdoctoral Development (SPD) Association. This includes election procedures for filling vacancies on the SPD board, an all-purpose voting procedure, and definitions for the roles and responsibilities of each SPD board member. The voting procedures can also be used to amend the by-laws, as well as to create, dissolve, or consolidate vacant SPD board positions.

  10. Development of explosive event scale model testing capability at Sandia`s large scale centrifuge facility

    Energy Technology Data Exchange (ETDEWEB)

    Blanchat, T.K.; Davie, N.T.; Calderone, J.J. [and others

    1998-02-01

    Geotechnical structures such as underground bunkers, tunnels, and building foundations are subjected to stress fields produced by the gravity load on the structure and/or any overlying strata. These stress fields may be reproduced on a scaled model of the structure by proportionally increasing the gravity field through the use of a centrifuge. This technology can then be used to assess the vulnerability of various geotechnical structures to explosive loading. Applications of this technology include assessing the effectiveness of earth penetrating weapons, evaluating the vulnerability of various structures, counter-terrorism, and model validation. This document describes the development of expertise in scale model explosive testing on geotechnical structures using Sandia`s large scale centrifuge facility. This study focused on buried structures such as hardened storage bunkers or tunnels. Data from this study was used to evaluate the predictive capabilities of existing hydrocodes and structural dynamics codes developed at Sandia National Laboratories (such as Pronto/SPH, Pronto/CTH, and ALEGRA). 7 refs., 50 figs., 8 tabs.

  11. Charter of the Sandia National Laboratories Sandia Postdoctoral Development (SPD) Association.

    Energy Technology Data Exchange (ETDEWEB)

    McBride, Amber Alane Fisher; McBride, Amber Alane Fisher; Rodgers, Theron; Dong, Wen; Juan, Pierre-Alexandre; Barkholtz, Heather; Alley, William Morgan; Wolk, Benjamin Matthew; Vane, Zachary Phillips; Priye, Aashish; Ball, Cameron Scott; McBride, Amber Alane Fisher

    2017-03-01

    The SNL SPD Association represents all personnel that are classified as Postdoctoral Appointees at Sandia National Laboratories. The purpose of the SNL SPD Association is to address the needs and concerns of Postdoctoral Appointees within Sandia National Laboratories.

  12. An analysis of microsystems development at Sandia National Laboratories

    Science.gov (United States)

    Herrera, Gilbert V.; Myers, David R.

    2011-06-01

    While Sandia initially was motivated to investigate emergent microsystem technology to miniaturize existing macroscale structures, present designs embody innovative approaches that directly exploit the fundamentally different material properties of a new technology at the micro- and nano-scale. Direct, hands-on experience with the emerging technology gave Sandia engineers insights that not only guided the evolution of the technology but also enabled them to address new applications that enlarged the customer base for the new technology. Sandia's early commitment to develop complex microsystems demonstrated the advantages that early adopters gain by developing an extensive design and process tool kit and a shared awareness of multiple approaches to achieve the multiple goals. As with any emergent technology, Sandia's program benefited from interactions with the larger technical community. However, custom development followed a spiral path of direct trial-and-error experience, analysis, quantification of materials properties at the micro- and nano-scale, evolution of design tools and process recipes, and an understanding of reliability factors and failure mechanisms even in extreme environments. The microsystems capability at Sandia relied on three key elements. The first was people: a mix of mechanical and semiconductor engineers, chemists, physical scientists, designers, and numerical analysts. The second was a unique facility that enabled the development of custom technologies without contaminating mainline product deliveries. The third was the arrival of specialized equipment as part of a Cooperative Research And Development Agreement (CRADA) enabled by the National Competitiveness Technology Transfer Act of 1989. Underpinning all these, the program was guided and sustained through the research and development phases by accomplishing intermediate milestones addressing direct mission needs.

  13. Sandia and NJ TRANSIT Authority Developing Resilient Power Grid

    Energy Technology Data Exchange (ETDEWEB)

    Hanley, Charles J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ellis, Abraham [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-11-01

    Through the memorandum of understanding between the Depratment of Energy (DOE), the New Jersey Transit Authority (NJ Transit), and the New Jersey Board of Public Utilities, Sandia National Labs is assisting NJ Transit in developing NJ TransitGrid: an electric microgrid that will include a large-scale gas-fired generation facility and distributed energy resources (photovoltaics [PV], energy storage, electric vehicles, combined heat and power [CHP]) to supply reliable power during storms or other times of significant power failure. The NJ TransitGrid was awarded $410M from the Department of Transportation to develop a first-of-its-kind electric microgrid capable of supplying highly-reliable power.

  14. The International Implications of the Development of Microelectronics.

    Science.gov (United States)

    Sieghart, Paul

    1981-01-01

    Synthesizes issues covered at a conference on microelectronics: production, productivity, and employment; social implications; market mechanisms v government intervention; the role of national governments; data protection laws; and cultural pollution. (SW)

  15. Sandia Agile MEMS Prototyping, Layout Tools, Education and Services Program

    Energy Technology Data Exchange (ETDEWEB)

    Schriner, H.; Davies, B.; Sniegowski, J.; Rodgers, M.S.; Allen, J.; Shepard, C.

    1998-05-01

    Research and development in the design and manufacture of Microelectromechanical Systems (MEMS) is growing at an enormous rate. Advances in MEMS design tools and fabrication processes at Sandia National Laboratories` Microelectronics Development Laboratory (MDL) have broadened the scope of MEMS applications that can be designed and manufactured for both military and commercial use. As improvements in micromachining fabrication technologies continue to be made, MEMS designs can become more complex, thus opening the door to an even broader set of MEMS applications. In an effort to further research and development in MEMS design, fabrication, and application, Sandia National Laboratories has launched the Sandia Agile MEMS Prototyping, Layout Tools, Education and Services Program or SAMPLES program. The SAMPLES program offers potential partners interested in MEMS the opportunity to prototype an idea and produce hardware that can be used to sell a concept. The SAMPLES program provides education and training on Sandia`s design tools, analysis tools and fabrication process. New designers can participate in the SAMPLES program and design MEMS devices using Sandia`s design and analysis tools. As part of the SAMPLES program, participants` designs are fabricated using Sandia`s 4 level polycrystalline silicon surface micromachine technology fabrication process known as SUMMiT (Sandia Ultra-planar, Multi-level MEMS Technology). Furthermore, SAMPLES participants can also opt to obtain state of the art, post-fabrication services provided at Sandia such as release, packaging, reliability characterization, and failure analysis. This paper discusses the components of the SAMPLES program.

  16. Energetic materials research and development activities at Sandia National Laboratories supported under DP-10 programs

    Energy Technology Data Exchange (ETDEWEB)

    Ratzel, A.C. III

    1998-09-01

    This report provides summary descriptions of Energetic Materials (EM) Research and Development activities performed at Sandia National Laboratories and funded through the Department of Energy DP-10 Program Office in FY97 and FY98. The work falls under three major focus areas: EM Chemistry, EM Characterization, and EM Phenomenological Model Development. The research supports the Sandia component mission and also Sandia's overall role as safety steward for the DOE Nuclear Weapons Complex.

  17. Synthetic aperture radar and interferometry development at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-04-01

    Environmental monitoring, earth-resource mapping, and military systems require broad-area imaging at high resolutions. Many times the imagery must be acquired in inclement weather or during night as well as day. Synthetic aperture radar (SAR) provides such a capability. SAR systems take advantage of the long-range propagation characteristics of radar signals and the complex information processing capability of modern digital electronics to provide high resolution imagery. SAR complements photographic and other optical imaging capabilities because of the minimum constrains on time-of-day and atmospheric conditions and because of the unique responses of terrain and cultural targets to radar frequencies. Interferometry is a method for generating a three-dimensional image of terrain. The height projection is obtained by acquiring two SAR images from two slightly differing locations. It is different from the common method of stereoscopic imaging for topography. The latter relies on differing geometric projections for triangulation to define the surface geometry whereas interferometry relies on differences in radar propagation times between the two SAR locations. This paper presents the capabilities of SAR, explains how SAR works, describes a few SAR applications, provides an overview of SAR development at Sandia, and briefly describes the motion compensation subsystem.

  18. History and testimony of competency-based development at Sandia National Laboratories.

    Energy Technology Data Exchange (ETDEWEB)

    Burt, Rebecca A.; Narahara, Sheryl K.

    2004-04-01

    More than ten years ago, Sandia managers defined a set of traits and characteristics that were needed for success at Sandia. Today, the Sandia National Laboratories Success Profile Competencies continue to be powerful tools for employee and leadership development. The purpose of this report is to revisit the historical events that led to the creation and adaptation of the competencies and to position them for integration in future employee selection, development, and succession planning processes. This report contains an account of how the competencies were developed, testimonies of how they are used within the organization, and a description of how they will be foundational elements of new processes.

  19. Sandia Technology engineering and science accomplishments

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    This report briefly discusses the following research being conducted at Sandia Laboratories: Advanced Manufacturing -- Sandia technology helps keep US industry in the lead; Microelectronics-Sandia`s unique facilities transform research advances into manufacturable products; Energy -- Sandia`s energy programs focus on strengthening industrial growth and political decisionmaking; Environment -- Sandia is a leader in environmentally conscious manufacturing and hazardous waste reduction; Health Care -- New biomedical technologies help reduce cost and improve quality of health care; Information & Computation -- Sandia aims to help make the information age a reality; Transportation -- This new initiative at the Labs will help improve transportation, safety,l efficiency, and economy; Nonproliferation -- Dismantlement and arms control are major areas of emphasis at Sandia; and Awards and Patents -- Talented, dedicated employees are the backbone of Sandia`s success.

  20. Microelectronic packaging

    CERN Document Server

    Datta, M; Schultze, J Walter

    2004-01-01

    Microelectronic Packaging analyzes the massive impact of electrochemical technologies on various levels of microelectronic packaging. Traditionally, interconnections within a chip were considered outside the realm of packaging technologies, but this book emphasizes the importance of chip wiring as a key aspect of microelectronic packaging, and focuses on electrochemical processing as an enabler of advanced chip metallization.Divided into five parts, the book begins by outlining the basics of electrochemical processing, defining the microelectronic packaging hierarchy, and emphasizing the impac

  1. Development and Testing of an Integrated Sandia Cooler Thermoelectric Device (SCTD).

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Terry A.; Staats, Wayne Lawrence,; Leick, Michael Thomas; Zimmerman, Mark D.; Radermacher, Reinhard; Martin, Cara; Nasuta, Dennis; Kalinowski, Paul; Hoffman, William

    2014-12-01

    This report describes a FY14 effort to develop an integrated Sandia Cooler T hermoelectric D evice (SCTD) . The project included a review of feasible thermoelectric (TE) cooling applications, baseline performance testing of an existing TE device, analysis and design development of an integrated SCTD assembly, and performance measurement and validation of the integrated SCTD prototype.

  2. Development and Evaluation of a Sandia Cooler-based Refrigerator Condenser

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Terry A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kariya, Harumichi Arthur [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Leick, Michael T. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Zimmerman, Mark D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Li, Manjie [Univ. of Maryland, College Park, MD (United States); Du, Yilin [Univ. of Maryland, College Park, MD (United States); Lee, Hoseong [Univ. of Maryland, College Park, MD (United States); Hwang, Yunho [Univ. of Maryland, College Park, MD (United States); Radermacher, Reinhard [Univ. of Maryland, College Park, MD (United States)

    2015-07-01

    This report describes the first design of a refrigerator condenser using the Sandia Cooler, i.e. air - bearing supported rotating heat - sink impeller. The project included ba seline performance testing of a residential refrigerator, analysis and design development of a Sandia Cooler condenser assembly including a spiral channel baseplate, and performance measurement and validation of this condenser system as incorporated into the residential refrigerator. Comparable performance was achieved in a 60% smaller volume package. The improved modeling parameters can now be used to guide more optimized designs and more accurately predict performance.

  3. Leadership development study :success profile competencies and high-performing leaders at Sandia National Laboratories.

    Energy Technology Data Exchange (ETDEWEB)

    Becker, Katherine M.; Mulligan, Deborah Rae; Szenasi, Gail L.; Crowder, Stephen Vernon

    2005-04-01

    Sandia is undergoing tremendous change. Sandia's executive management recognized the need for leadership development. About ten years ago the Business, Leadership, and Management Development department in partnership with executive management developed and implemented the organizational leadership Success Profile Competencies to help address some of the changes on the horizon such as workforce losses and lack of a skill set in the area of interpersonal skills. This study addresses the need for the Business, Leadership, and Management Development department to provide statistically sound data in two areas. One is to demonstrate that the organizational 360-degree success profile assessment tool has made a difference for leaders. A second area is to demonstrate the presence of high performing leaders at the Labs. The study utilized two tools to address these two areas. Study participants were made up of individuals who have solid data on Sandia's 360-degree success profile assessment tool. The second assessment tool was comprised of those leaders who participated in the Lockheed Martin Corporation Employee Preferences Survey. Statistical data supports the connection between leader indicators and the 360-degree assessment tool. The study also indicates the presence of high performing leaders at Sandia.

  4. Technological Change and Women Workers: The Development of Microelectronics. World Conference of the United Nations Decade for Women: Equality, Development, and Peace.

    Science.gov (United States)

    Hult, Marit

    This report reviews the current debate in industrialized market economy countries on the impact of microelectronics technology on employment. A special focus is on the impact on women's employment opportunities. Chapter 1 presents information on the technological background, including the development of microelectronics and their application in…

  5. Biomedical implantable microelectronics.

    Science.gov (United States)

    Meindl, J D

    1980-10-17

    Innovative applications of microelectronics in new biomedical implantable instruments offer a singular opportunity for advances in medical research and practice because of two salient factors: (i) beyond all other types of biomedical instruments, implants exploit fully the inherent technical advantages--complex functional capability, high reliability, lower power drain, small size and weight-of microelectronics, and (ii) implants bring microelectronics into intimate association with biological systems. The combination of these two factors enables otherwise impossible new experiments to be conducted and new paostheses developed that will improve the quality of human life.

  6. Review of Sandia National Laboratories - Albuquerque, New Mexico DOE/DP critical skills development programs FY03.

    Energy Technology Data Exchange (ETDEWEB)

    Clark, Katherine Sue; Wilson, Dominique Foley; Chalamidas, Anna K.

    2004-04-01

    Sandia National Laboratories has developed a portfolio of programs to address the critical skills needs of the DP labs, as identified by the 1999 Chiles Commission Report. The goals are to attract and retain the best and the brightest students and transition them into Sandia - and DP Complex - employees. The US Department of Energy/Defense Programs University Partnerships funded nine laboratory critical skills development programs in FY03. This report provides a qualitative and quantitative evaluation of these programs and their status.

  7. Superconducting Microelectronics.

    Science.gov (United States)

    Henry, Richard W.

    1984-01-01

    Discusses superconducting microelectronics based on the Josephson effect and its advantages over conventional integrated circuits in speed and sensitivity. Considers present uses in standards laboratories (voltage) and in measuring weak magnetic fields. Also considers future applications in superfast computer circuitry using Superconducting…

  8. Radiation-Induced Prompt Photocurrents in Microelectronics Physics

    CERN Document Server

    Dodd, P E; Buller, D L; Doyle, B L; Vizkelethy, G; Walsh, D S

    2003-01-01

    The effects of photocurrents in nuclear weapons induced by proximal nuclear detonations are well known and remain a serious hostile environment threat for the US stockpile. This report describes the final results of an LDRD study of the physical phenomena underlying prompt photocurrents in microelectronic devices and circuits. The goals of this project were to obtain an improved understanding of these phenomena, and to incorporate improved models of photocurrent effects into simulation codes to assist designers in meeting hostile radiation requirements with minimum build and test cycles. We have also developed a new capability on the ion microbeam accelerator in Sandia's Ion Beam Materials Research Laboratory (the Transient Radiation Microscope, or TRM) to supply ionizing radiation in selected micro-regions of a device. The dose rates achieved in this new facility approach those possible with conventional large-scale dose-rate sources at Sandia such as HERMES III and Saturn. It is now possible to test the phy...

  9. Microelectronics in Scottish Education.

    Science.gov (United States)

    Morris, Ian

    1982-01-01

    Describes the Scottish Microelectronics Development Programme (SMDP), which was undertaken to advance the use of microcomputers in instruction at all educational levels in Scotland. The development of the microprocessor and its effect on educational technology are briefly considered, as well as initial problems and prospects for the future of…

  10. Microelectronic systems 3 checkbook

    CERN Document Server

    Vears, R E

    1985-01-01

    Microelectronic Systems 3: Checkbook aims to extend the range of hardware, software, and interfacing techniques developed at level 2. This book concentrates on the highly popular 6502, Z80, and 6800 microprocessors and contains approximately 70 tested programs that may be used with little or no modification on most systems based on these microprocessors. This text also covers the main points concerned with computer hardware configuration, interfacing devices, subroutines and the stack, polling and interrupts, microelectronic stores, and address decoding and organization. Each chapter of the b

  11. Review of the Sandia National Laboratories -- Albuquerque, New Mexico DOE/DP Critical Skills Development Programs FY '02

    Energy Technology Data Exchange (ETDEWEB)

    CLARK, KATHERINE SUE

    2003-02-01

    Sandia National Laboratories has developed a portfolio of programs to address the critical skills needs of the DP labs, as identified by the 1999 Chiles Commission Report. The goals are to attract and retain the best and the brightest students and transition them into Sandia--and DP Complex--employees. The US Department of Energy/Defense Programs University Partnerships funded seven laboratory critical skills development programs in FY02. This report provides a qualitative and quantitative evaluation of these programs and their status.

  12. Review of Sandia National Laboratories - Albuquerque New Mexico DOE/DP Critical Skills Development Progrmas FY04.

    Energy Technology Data Exchange (ETDEWEB)

    Gorman, Anna K; Wilson, Dominique; CLARK, KATHERINE

    2005-09-01

    Sandia National Laboratories has developed a portfolio of programs to address the critical skills needs of the DP labs, as identified by the 1999 Chiles Commission Report. The goals are to attract and retain the best and the brightest students and transition them into Sandia - and DP Complex - employees. The US Department of Energy/Defense Programs University Partnerships funded ten laboratory critical skills development programs in FY04. This report provides a qualitative and quantitative evaluation of these programs and their status. 3

  13. Carbon nanotubes for microelectronics?

    Science.gov (United States)

    Graham, Andrew P; Duesberg, Georg S; Seidel, Robert V; Liebau, Maik; Unger, Eugen; Pamler, Werner; Kreupl, Franz; Hoenlein, Wolfgang

    2005-04-01

    Despite all prophecies of its end, silicon-based microelectronics still follows Moore's Law and continues to develop rapidly. However, the inherent physical limits will eventually be reached. Carbon nanotubes offer the potential for further miniaturization as long as it is possible to selectively deposit them with defined properties.

  14. RADC/NBS (Rome Air Development Center/National Bureau of Standards) Workshop. Moisture Measurement and Control for Microelectronics (4)

    Science.gov (United States)

    Kane, Didier; Moore, Benjamin A.; Walters, E. Jane

    1987-06-01

    The fourth workshop on Moisture Measurement and Control for Microelectronics served as a forum on moisture and/or materials reliability problems and on ways to control them or measure their extent. Twenty-two presentations are included which contain detailed information on hermeticity measurement and definition; development of standard packages for mass spectrometric calibrations; moisture interaction with various materials; and techniques that can be used to measure moisture microelectronics. It was clear from several presentations in the workshop that a very systematic approach is needed when organic materials are involved; all the variables must be identified and studied one at a time. This is the key to lot-to-lot reproducibility, materials selection, and control; hence a better reliability at the design phase will decrease the need for testing; hence the cost, thus resulting in a greater satisfaction to the customer.

  15. Sandia Strategic Plan 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    Sandia embarked on its first exercise in corporate strategic planning during the winter of 1989. The results of that effort were disseminated with the publication of Strategic Plan 1990. Four years later Sandia conducted their second major planning effort and published Strategic Plan 1994. Sandia`s 1994 planning effort linked very clearly to the Department of Energy`s first strategic plan, Fueling a Competitive Economy. It benefited as well from the leadership of Lockheed Martin Corporation, the management and operating contractor. Lockheed Martin`s corporate success is founded on visionary strategic planning and annual operational planning driven by customer requirements and technology opportunities. In 1996 Sandia conducted another major planning effort that resulted in the development of eight long-term Strategic Objectives. Strategic Plan 1997 differs from its predecessors in that the robust elements of previous efforts have been integrated into one comprehensive body. The changes implemented so far have helped establish a living strategic plan with a stronger business focus and with clear deployment throughout Sandia. The concept of a personal line of sight for all employees to this strategic plan and its objectives, goals, and annual milestones is becoming a reality.

  16. Sandia Strategic Plan 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    Sandia embarked on its first exercise in corporate strategic planning during the winter of 1989. The results of that effort were disseminated with the publication of Strategic Plan 1990. Four years later Sandia conducted their second major planning effort and published Strategic Plan 1994. Sandia`s 1994 planning effort linked very clearly to the Department of Energy`s first strategic plan, Fueling a Competitive Economy. It benefited as well from the leadership of Lockheed Martin Corporation, the management and operating contractor. Lockheed Martin`s corporate success is founded on visionary strategic planning and annual operational planning driven by customer requirements and technology opportunities. In 1996 Sandia conducted another major planning effort that resulted in the development of eight long-term Strategic Objectives. Strategic Plan 1997 differs from its predecessors in that the robust elements of previous efforts have been integrated into one comprehensive body. The changes implemented so far have helped establish a living strategic plan with a stronger business focus and with clear deployment throughout Sandia. The concept of a personal line of sight for all employees to this strategic plan and its objectives, goals, and annual milestones is becoming a reality.

  17. Development of low dielectric constant alumina-based ceramics for microelectronic substrates

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Shun Jackson [Univ. of California, Berkeley, CA (United States)

    1993-05-01

    The performance of high speed computers depends not only on IC chips, but also on the signal propagation speed between these chips. The signal propagation delay in a computer is determined by the dielectric constant of the substrate material to which the IC chips are attached. In this study, a ceramic substrate with a low dielectric constant (k ≈ 5.0) has been developed. When compared with the traditional alumina substrate (k ≈ 10.0), the new material corresponds to a 37% decrease in the signal propagation delay. Glass hollow spheres are used to introduce porosity (k = 1.0) to the alumina matrix in a controlled manner. A surface coating technique via heterogeneous nucleation in aqueous solution has been used to improve the high temperature stability of these spheres. After sintering at 1,400 C, isolated spherical pores are uniformly distributed in the almost fully dense alumina matrix; negligible amounts of matrix defects can be seen. All pores are isolated from each other. Detailed analyses of the chemical composition find that the sintered sample consists of α-alumina, mullite and residual glass. Mullite is the chemical reaction product of alumina and the glass spheres. Residual glass exists because current firing conditions do not complete the mullitization reaction. The dielectric constant of the sintered sample is measured and then compared with the predicted value using Maxwell`s model. Mechanical strength is evaluated by a four-point bending test. Although the flexural strength decreases exponentially with porosity, samples with 34% porosity (k ≈ 5.0) still maintain adequate mechanical strength for the proper operation of a microelectronic substrate.

  18. Nanosatellite program at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, D.A.; Kern, J.P.; Schoeneman, J.L.

    1999-11-11

    The concept of building extremely small satellites which, either independently or as a collective, can perform missions which are comparable to their much larger cousins, has fascinated scientists and engineers for several years now. In addition to the now commonplace microelectronic integrated circuits, the more recent advent of technologies such as photonic integrated circuits (PIC's) and micro-electromechanical systems (MEMS) have placed such a goal within their grasp. Key to the acceptance of this technology will be the ability to manufacture these very small satellites in quantity without sacrificing their performance or versatility. In support of its nuclear treaty verification, proliferation monitoring and other remote sensing missions, Sandia National laboratories has had a 35-year history of providing highly capable systems, densely packaged for unintrusive piggyback missions on government satellites. As monitoring requirements have become more challenging and remote sensing technologies become more sophisticated, packaging greater capability into these systems has become a requirement. Likewise, dwindling budgets are pushing satellite programs toward smaller and smaller platforms, reinforcing the need for smaller, cheaper satellite systems. In the next step of its miniaturization plan, Sandia has begun development of technologies for a highly integrated miniature satellite. The focus of this development is to achieve nanosat or smaller dimensions while maintaining significant capability utilizing semiconductor wafer-level integration and, at the same time promoting affordability through modular generic construction.

  19. Prototype prosperity-diversity game for the Laboratory Development Division of Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    VanDevender, P.; Berman, M.; Savage, K.

    1996-02-01

    The Prosperity Game conducted for the Laboratory Development Division of National Laboratories on May 24--25, 1995, focused on the individual and organizational autonomy plaguing the Department of Energy (DOE)-Congress-Laboratories` ability to manage the wrenching change of declining budgets. Prosperity Games are an outgrowth and adaptation of move/countermove and seminar War Games. Each Prosperity Game is unique in that both the game format and the player contributions vary from game to game. This particular Prosperity Game was played by volunteers from Sandia National Laboratories, Eastman Kodak, IBM, and AT&T. Since the participants fully control the content of the games, the specific outcomes will be different when the team for each laboratory, Congress, DOE, and the Laboratory Operating Board (now Laboratory Operations Board) is composed of executives from those respective organizations. Nevertheless, the strategies and implementing agreements suggest that the Prosperity Games stimulate cooperative behaviors and may permit the executives of the institutions to safely explore the consequences of a family of DOE concert.

  20. Development of Drop/Shock Test in Microelectronics and Impact Dynamic Analysis for Uniform Board Response

    Science.gov (United States)

    Kallolimath, Sharan Chandrashekar

    -joints. No ring test conditions was proposed and verified for the current widely used JEDEC standard. The significance of impact loading parameters such as pulse magnitude, pulse duration, pulse shapes and board dynamic parameter such as linear hysteretic damping and dynamic stiffness were discussed. Third, Kirchhoff's plate theory by principle of minimum potential energy was adopted to develop the FEA formulation to consider the effect of material hysteretic damping for the currently used JEDEC board test and proposed no-ring response test condition. Fourth, a hexagonal symmetrical board model was proposed to address the uniform stress and strain distribution throughout the test board and identify the critical failure factors. Dynamic stress and strain of the hexagonal board model were then compared with standard JEDEC board for both standard and proposed no-ring test conditions. In general, this line of research demonstrates that advanced techniques of FEA analysis can provide useful insights concerning the optimal design of drop test in microelectronics.

  1. The SEMATECH - Sandia National Laboratories partnership: A case study

    Energy Technology Data Exchange (ETDEWEB)

    Carayannis, E. [George Washington Univ., DC (United States). School of Business and Public Management; Gover, J. [Sandia National Labs., Albuquerque, NM (United States)

    1997-11-01

    SEMATECH was established in 1987 for defense and economic reasons to help the U.S. regain a competitive posture in semiconductor manufacturing. For 10 years SEMATECH was jointly funded by the federal government and semiconductor manufacturing companies representing 85 percent of the U.S. semiconductor industry. SEMATECH has spent about 80 percent of these funds on activities intended to produce useful results between 1 and 3 years. Very early in the establishment of SEMATECH, its members determined that their first priority would be to strengthen their U.S. based suppliers of semiconductor manufacturing equipment. This has been the primary thrust of SEMATECH. SEMATECH first held some 30 workshops on a broad set of technical topics to assess the needs and opportunities to help the industry recover. These workshops scoped manufacturing areas where SEMATECH should focus. These early meetings were an early form of what later came to be termed roadmapping. The scope of R&D needs identified in these workshops well exceeded what SEMATECH could hope to accomplish with its $200 million annual budget. Wayne Johnson of Sandia participated in five of these workshops and used the knowledge gained as the basis for proposals later submitted to SEMATECH on behalf of Sandia. In the fall of 1989 the SETEC program was established at Sandia to support SEMATECH. This was initially a funds-in, work-for-others project that was fully funded by SEMATECH. Thus, the early work was entirely focused on SEMATECH`s needs. Later in the program when SEMATECH funds were supplemented by Department of Energy Cooperative Research and Development funds, attention was given to how this project would benefit Sandia`s defense microelectronics program.

  2. Microelectronics plastic molded packaging

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, D.R. [Ktech Corp., Albuquerque, NM (United States); Palmer, D.W.; Peterson, D.W. [Sandia National Lab., Albuquerque, NM (United States)] [and others

    1997-02-01

    The use of commercial off-the-shelf (COTS) microelectronics for nuclear weapon applications will soon be reality rather than hearsay. The use of COTS for new technologies for uniquely military applications is being driven by the so-called Perry Initiative that requires the U.S. Department of Defense (DoD) to accept and utilize commercial standards for procurement of military systems. Based on this philosophy, coupled with several practical considerations, new weapons systems as well as future upgrades will contain plastic encapsulated microelectronics. However, a conservative Department of Energy (DOE) approach requires lifetime predictive models. Thus, the focus of the current project is on accelerated testing to advance current aging models as well as on the development of the methodology to be used during WR qualification of plastic encapsulated microelectronics. An additional focal point involves achieving awareness of commercial capabilities, materials, and processes. One of the major outcomes of the project has been the definition of proper techniques for handling and evaluation of modern surface mount parts which might be used in future systems. This program is also raising the familiarity level of plastic within the weapons complex, allowing subsystem design rules accommodating COTS to evolve. A two year program plan is presented along with test results and commercial interactions during this first year.

  3. Sandia National Laboratories embraces ISDN

    Energy Technology Data Exchange (ETDEWEB)

    Tolendino, L.F.; Eldridge, J.M.

    1994-08-01

    Sandia National Laboratories (Sandia), a multidisciplinary research and development laboratory located on Kirtland Air Force Base, has embraced Integrated Services Digital Network technology as an integral part of its communication network. Sandia and the Department of Energy`s Albuquerque Operations Office have recently completed the installation of a modernized and expanded telephone system based, on the AT&T 5ESS telephone switch. Sandia is committed to ISDN as an integral part of data communication services, and it views ISDN as one part of a continuum of services -- services that range from ISDN`s asynchronous and limited bandwidth Ethernet (250--1000 Kbps) through full bandwidth Ethernet, FDDI, and ATM at Sonet rates. Sandia has demonstrated this commitment through its use of ISDN data features to support critical progmmmatic services such as access to corporate data base systems. In the future, ISDN will provide enhanced voice, data communication, and video services.

  4. Sandia National Laboratories

    Data.gov (United States)

    Federal Laboratory Consortium — For more than 60 years, Sandia has delivered essential science and technology to resolve the nation's most challenging security issues.Sandia National Laboratories...

  5. Polymers for microelectronics

    Directory of Open Access Journals (Sweden)

    Gerhard Maier

    2001-09-01

    Full Text Available The continuous advancement of microelectronics in all fields of technology has become a basic fact of our daily life. Increasingly complex tasks are performed by computers, requiring more memory capacity and faster processing speeds. This constant need to develop more highly integrated microchips is expressed by Moore's law, which states that the capacity of the most highly developed random access memory (RAM chips increases by a factor of four every three years. This is achieved by decreasing the size of devices on chips in each new generation by a factor of two and simultaneously increasing the size of the silicon chip (‘die’ by the same factor.

  6. Committee to evaluate Sandia`s risk expertise: Final report. Volume 1: Presentations

    Energy Technology Data Exchange (ETDEWEB)

    Dudley, E.C.

    1998-05-01

    On July 1--2, 1997, Sandia National Laboratories hosted the External Committee to Evaluate Sandia`s Risk Expertise. Under the auspices of SIISRS (Sandia`s International Institute for Systematic Risk Studies), Sandia assembled a blue-ribbon panel of experts in the field of risk management to assess their risk programs labs-wide. Panelists were chosen not only for their own expertise, but also for their ability to add balance to the panel as a whole. Presentations were made to the committee on the risk activities at Sandia. In addition, a tour of Sandia`s research and development programs in support of the US Nuclear Regulatory Commission was arranged. The panel attended a poster session featuring eight presentations and demonstrations for selected projects. Overviews and viewgraphs from the presentations are included in Volume 1 of this report. Presentations are related to weapons, nuclear power plants, transportation systems, architectural surety, environmental programs, and information systems.

  7. The Legacy of the Microelectronics Education Programme.

    Science.gov (United States)

    Thorne, Michael

    1987-01-01

    Describes the Microelectronics Education Programme (MEP), a plan developed to help British secondary school students learn about microcomputers and the role of technology in society, and its successor, the Microelectronics Support Unit (MESU). Highlights include curriculum development, teacher training, computer assisted instruction and the…

  8. Sandia software guidelines: Volume 5, Tools, techniques, and methodologies

    Energy Technology Data Exchange (ETDEWEB)

    1989-07-01

    This volume is one in a series of Sandia Software Guidelines intended for use in producing quality software within Sandia National Laboratories. This volume describes software tools and methodologies available to Sandia personnel for the development of software, and outlines techniques that have proven useful within the Laboratories and elsewhere. References and evaluations by Sandia personnel are included. 6 figs.

  9. Cold-Cathodes for Sensors and Vacuum Microelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Siegal, M.P.; Sullivan, J.P.; Tallant, D.R.; Simpson, R.L. [Sandia National Labs., Albuquerque, NM (United States); DiNardo, N.J.; Mercer, T.W. [Drexel Univ., Philadelphia, PA (United States). Dept. of Physics and Astronomy; Martinez-Miranda, L.J. [Univ. of Maryland, College Park, MD (United States). Dept. of Materials Science and Engineering

    1998-05-01

    The aim of this laboratory-directed research and development project was to study amorphous carbon (a-C) thin films for eventual cold-cathode electron emitter applications. The development of robust, cold-cathode emitters are likely to have significant implications for modern technology and possibly launch a new industry: vacuum micro-electronics (VME). The potential impact of VME on Sandia`s National Security missions, such as defense against military threats and economic challenges, is profound. VME enables new microsensors and intrinsically radiation-hard electronics compatible with MOSFET and IMEM technologies. Furthermore, VME is expected to result in a breakthrough technology for the development of high-visibility, low-power flat-panel displays. This work covers four important research areas. First, the authors studied the nature of the C-C bonding structures within these a-C thin films. Second, they determined the changes in the film structures resulting from thermal annealing to simulate the effects of device processing on a-C properties. Third, they performed detailed electrical transport measurements as a function of annealing temperature to correlate changes in transport properties with structural changes and to propose a model for transport in these a-C materials with implications on the nature of electron emission. Finally, they used scanning atom probes to determine important aspects on the nature of emission in a-C.

  10. Launching a Programme on Microelectronics.

    Science.gov (United States)

    Fothergill, Richard

    1982-01-01

    Discusses the priorities and problems in the development by the United Kingdom Department of Education and Science of a program to introduce microelectronic technology to elementary and secondary level students. The basic needs for program implementation, information support required for the program, inservice teacher training, and curriculum…

  11. Microelectronics in Education

    Science.gov (United States)

    Orton, Richard J. J.

    2011-01-01

    The history and meaning of the term "microelectronics" is reviewed, followed by a discussion of the key inventions of the Intel microprocessor in 1971 and the Texas Instruments electronic pocket calculator in 1975. The six characteristic features of microelectronic components are then defined. The UK prime minister Jim Callaghan's…

  12. Microelectronics and Music Education.

    Science.gov (United States)

    Hofstetter, Fred T.

    1979-01-01

    This look at the impact of microelectronics on computer-assisted instruction (CAI) in music notes trends toward new applications and lower costs. Included are: a rationale for CAI in music, a list of sample programs, comparison of five microelectronic music systems, PLATO cost projections, and sources of further information. (SJL)

  13. Microelectronics in Education

    Science.gov (United States)

    Orton, Richard J. J.

    2011-01-01

    The history and meaning of the term "microelectronics" is reviewed, followed by a discussion of the key inventions of the Intel microprocessor in 1971 and the Texas Instruments electronic pocket calculator in 1975. The six characteristic features of microelectronic components are then defined. The UK prime minister Jim Callaghan's address to the…

  14. Microelectronics, radiation, and superconductivity.

    Science.gov (United States)

    Gochfeld, M

    1990-06-01

    Among the costs of technology are health hazards that face employees and consumers. New advances in the highly competitive field of microelectronics involve exposure to a variety of hazards such as gallium arsenide. Small high-technology industries appear unprepared to invest in health and safety. Although stray electromagnetic fields are not a new development, researchers are beginning to assemble data indicating that such fields pose a significant cancer risk under certain circumstances. Data have been obtained on fields associated with power lines on the one hand and consumer products on the other. Although not conclusive, the data are sufficient to warrant carefully designed research into the risks posed by electromagnetic fields. Because the scientific issues require research, there is a need to make basic social value decisions that will determine which technologies will be developed and which ones may be set aside because of their danger at the present time.

  15. Diagnostics and Microelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Balch, J.W.

    1993-03-01

    This report discusses activities of the Diagnostics and Microelectronics thrust area which conducts activities in semiconductor devices and semiconductor fabrication technology for programs at Lawrence Livermore National Laboratory. Our multidisciplinary engineering and scientific staff use modern computational tools and semi-conductor microfabrication equipment to develop high-performance devices. Our work concentrates on three broad technologies of semiconductor microdevices: (1) silicon on III-V semiconductor microeletronics, (2) lithium niobate-based and III-V semiconductor-based photonics, and (3) silicon-based micromaching for application to microstructures and microinstruments. In FY-92, we worked on projects in seven areas, described in this report: novel photonic detectors; a wideband phase modulator; an optoelectronic terahertz beam system; the fabrication of microelectrode electrochemical sensors; diamond heatsinks; advanced micromachining technologies; and electrophoresis using silicon microchannels.

  16. The Microelectronics Education Programme--Dissemination and Diffusion of Microelectronics Technology in Education.

    Science.gov (United States)

    Milne, J. A.; Anderson, J. S. A.

    1984-01-01

    Describes the Microelectronics Education Programme, a development program which embodies the building of a springboard for the dissemination of microelectronic innovations that will benefit education. Springboard activities discussed in detail include information dissemination through regional information centers, inservice teacher training, and…

  17. Mobile robotics research at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Morse, W.D.

    1998-09-01

    Sandia is a National Security Laboratory providing scientific and engineering solutions to meet national needs for both government and industry. As part of this mission, the Intelligent Systems and Robotics Center conducts research and development in robotics and intelligent machine technologies. An overview of Sandia`s mobile robotics research is provided. Recent achievements and future directions in the areas of coordinated mobile manipulation, small smart machines, world modeling, and special application robots are presented.

  18. New Polymer Materials for Microelectronics Packaging

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ Researchers at the CAS Institute of Chemistry (ICCAS) have made breakthrough progress in developing the manufacturing technology of advanced polymer materials for microelectronics packaging applications. The advanced integrated circuit (IC) packaging polymer materials, including photoimageable polyimide resins and liquid epoxy underfills, are a key issue for FC-BGA/CSP(flip chip-ball grill array/chip scale packaging) which is the main stream for the next generation of microelectronics devices. With the down-sizing, thinning and high I/O (input/output) of IC chips, microelectronics packaging is now facing a big technology challenge.

  19. This is Sandia

    Energy Technology Data Exchange (ETDEWEB)

    1995-02-01

    Sandia is a multiprogram engineering and science laboratory operated for the Department of Energy with major facilities at Albuquerque, New Mexico, and Livermore, California, and a test range near Tonapah, Nevada. It has major research and development responsibilities for nuclear weapons, arms control, energy, the environment, economic competitiveness, and other areas of importance to the needs of the nation. The principal mission is to support national defense policies by ensuring that the nuclear weapon stockpile meets the highest standards of safety, reliability, security, use control, and military performance. This publication gives a brief overview of the multifaceted research programs conducted by the laboratory.

  20. Microelectronic systems 1 checkbook

    CERN Document Server

    Vears, R E

    2013-01-01

    Microelectronic Systems 1 Checkbook provides coverage of the Business and Technician Education Council level 1 unit in Microelectronic Systems. However, it can be regarded as a basic textbook in microelectronic systems for a much wider range of studies. Each topic considered in the text is presented in a way that assumes the reader has little prior knowledge of electronics. The aim of the book is to provide an introduction to the concept of systems, to differentiate analogue and digital systems, and to describe the nature of microprocessor-controlled systems. An introduction to programming is

  1. Sandia`s network for supercomputing `95: Validating the progress of Asynchronous Transfer Mode (ATM) switching

    Energy Technology Data Exchange (ETDEWEB)

    Pratt, T.J.; Vahle, O.; Gossage, S.A.

    1996-04-01

    The Advanced Networking Integration Department at Sandia National Laboratories has used the annual Supercomputing conference sponsored by the IEEE and ACM for the past three years as a forum to demonstrate and focus communication and networking developments. For Supercomputing `95, Sandia elected: to demonstrate the functionality and capability of an AT&T Globeview 20Gbps Asynchronous Transfer Mode (ATM) switch, which represents the core of Sandia`s corporate network, to build and utilize a three node 622 megabit per second Paragon network, and to extend the DOD`s ACTS ATM Internet from Sandia, New Mexico to the conference`s show floor in San Diego, California, for video demonstrations. This paper documents those accomplishments, discusses the details of their implementation, and describes how these demonstrations supports Sandia`s overall strategies in ATM networking.

  2. Testing microelectronic biofluidic systems

    NARCIS (Netherlands)

    Kerkhoff, Hans G.

    2007-01-01

    According to the 2005 International Technology Roadmap for Semiconductors, the integration of emerging nondigital CMOS technologies will require radically different test methods, posing a major challenge for designers and test engineers. One such technology is microelectronic fluidic (MEF) arrays,

  3. Testing microelectronic biofluidic systems

    NARCIS (Netherlands)

    Kerkhoff, Hans G.

    2007-01-01

    According to the 2005 International Technology Roadmap for Semiconductors, the integration of emerging nondigital CMOS technologies will require radically different test methods, posing a major challenge for designers and test engineers. One such technology is microelectronic fluidic (MEF) arrays, w

  4. Microelectronics to nanoelectronics materials, devices & manufacturability

    CERN Document Server

    Kaul, Anupama B

    2012-01-01

    Composed of contributions from top experts, Microelectronics to Nanoelectronics: Materials, Devices and Manufacturability offers a detailed overview of important recent scientific and technological developments in the rapidly evolving nanoelectronics arena.Under the editorial guidance and technical expertise of noted materials scientist Anupama B. Kaul of California Institute of Technology's Jet Propulsion Lab, this book captures the ascent of microelectronics into the nanoscale realm. It addresses a wide variety of important scientific and technological issues in nanoelectronics research and

  5. Sandia Combustion Research Program

    Energy Technology Data Exchange (ETDEWEB)

    Johnston, S.C.; Palmer, R.E.; Montana, C.A. (eds.)

    1988-01-01

    During the late 1970s, in response to a national energy crisis, Sandia proposed to the US Department of Energy (DOE) a new, ambitious program in combustion research. Shortly thereafter, the Combustion Research Facility (CRF) was established at Sandia's Livermore location. Designated a ''user facility,'' the charter of the CRF was to develop and maintain special-purpose resources to support a nationwide initiative-involving US inventories, industry, and national laboratories--to improve our understanding and control of combustion. This report includes descriptions several research projects which have been simulated by working groups and involve the on-site participation of industry scientists. DOE's Industry Technology Fellowship program, supported through the Office of Energy Research, has been instrumental in the success of some of these joint efforts. The remainder of this report presents results of calendar year 1988, separated thematically into eleven categories. Referred journal articles appearing in print during 1988 and selected other publications are included at the end of Section 11. Our traditional'' research activities--combustion chemistry, reacting flows, diagnostics, engine and coal combustion--have been supplemented by a new effort aimed at understanding combustion-related issues in the management of toxic and hazardous materials.

  6. Microelectronics: The Nature of Work, Skills and Training. An Analysis of Case Studies from Developed and Developing Countries. Training Discussion Paper No. 51.

    Science.gov (United States)

    Acero, Liliana

    Microelectronic technologies have had an impact on the nature of work in industry for both white-collar and blue-collar workers. Evidence from sector- and enterprise-level studies shows changes in skills and job content for blue-collar workers involved with numerically controlled machine tools, robots, and other microelectronics applications.…

  7. A new approach in the development of quality management systems for (micro)electronics

    Science.gov (United States)

    Bacivarov, Ioan C.; Bacivarov, Angelica; Gherghina, Cǎtǎlina

    2016-12-01

    This paper presents the new approach in the analysis of the Quality Management Systems (QMS) of companies, based on the revised standard ISO 9001:2015. In the first part of the paper, QMS based on ISO 9001 certification are introduced; the changes and the updates proposed for the new version of ISO 9001:2015 are critically analyzed, based on the documents elaborated by ISO/TC 176. The approach based on ISO 9001:2015 could be considered as "beginning of a new era in development of quality management systems". A comparison between the between the "old" standard ISO 9001:2008 and the "new" standard ISO 9001:2015 is made. In the second part of the paper, steps to be followed in a company to implement this new standard are presented. A peculiar attention is given to the new concept of risk-based thinking in order to support and improve application of the process based approach. The authors conclude that, by considering risk throughout the organization the likelihood of achieving stated objectives is improved, output is more consistent and customers can be confident that they will receive the expected results. Finally, the benefits of the new approach in the development of quality management systems are outlined, as well as how they are reflected in the management of companies in general and those in electronics field, in particular. As demonstrated in this paper, well understood and properly applied, the new approach based on the revised standard ISO9001:2015 could offer a better quality management for companies operating in electronics and beyond.

  8. NMSBA: Sandia Biotech 2016 Report

    Energy Technology Data Exchange (ETDEWEB)

    Ruffing, Anne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-06-01

    The objective of this project is to modify the FluorAbody plasmid previously developed by Sandia Biotech to include a binding site for biotin by introducing the biotin carboxyl carrier protein (BCCP)and a gold binding protein (GBP) into a loop of the red fluorescent protein (mRFP).

  9. Nanoscale Microelectronic Circuit Development

    Science.gov (United States)

    2011-06-17

    26. Sensitivity of the transient collector and emitter currents of a npn bipolar transistor to the doping level in the n-type...collector and emitter currents of a npn bipolar transistor to the doping level in the n-type collector region. Also shown are the sensitivities computed...semiconductor transistor NPN Negative-positive-negative ns Nanosecond nsec Nanosecond (Millimicrosecond) nW Nanowatt Op amp Operational amplifier OTA

  10. Sandia OpenSHMEM

    Energy Technology Data Exchange (ETDEWEB)

    2016-03-15

    Sandia OpenSHMEM is an implementation of the OpenSHMEM Standard over the Portals 4 Networking API and the OpenFabrics Interface (OFI). Sandia OpenSHMEM is designed to be a low-overhead implementation of the OpenSHMEM standard which takes advantage of the many features of the Portals 4 specification.

  11. Advanced modeling and simulation to design and manufacture high performance and reliable advanced microelectronics and microsystems.

    Energy Technology Data Exchange (ETDEWEB)

    Nettleship, Ian (University of Pittsburgh, Pittsburgh, PA); Hinklin, Thomas; Holcomb, David Joseph; Tandon, Rajan; Arguello, Jose Guadalupe, Jr. (,; .); Dempsey, James Franklin; Ewsuk, Kevin Gregory; Neilsen, Michael K.; Lanagan, Michael (Pennsylvania State University, University Park, PA)

    2007-07-01

    An interdisciplinary team of scientists and engineers having broad expertise in materials processing and properties, materials characterization, and computational mechanics was assembled to develop science-based modeling/simulation technology to design and reproducibly manufacture high performance and reliable, complex microelectronics and microsystems. The team's efforts focused on defining and developing a science-based infrastructure to enable predictive compaction, sintering, stress, and thermomechanical modeling in ''real systems'', including: (1) developing techniques to and determining materials properties and constitutive behavior required for modeling; (2) developing new, improved/updated models and modeling capabilities, (3) ensuring that models are representative of the physical phenomena being simulated; and (4) assessing existing modeling capabilities to identify advances necessary to facilitate the practical application of Sandia's predictive modeling technology.

  12. Chemistry in microelectronics

    CERN Document Server

    Le Tiec, Yannick

    2013-01-01

    Microelectronics is a complex world where many sciences need to collaborate to create nano-objects: we need expertise in electronics, microelectronics, physics, optics and mechanics also crossing into chemistry, electrochemistry, as well as biology, biochemistry and medicine. Chemistry is involved in many fields from materials, chemicals, gases, liquids or salts, the basics of reactions and equilibrium, to the optimized cleaning of surfaces and selective etching of specific layers. In addition, over recent decades, the size of the transistors has been drastically reduced while the functionalit

  13. Electronic and Microelectronic Capabilities.

    Science.gov (United States)

    1982-07-01

    22 3.9 Aztec Products Custom Wet-Chemistry Line ........................................... 22 3.10 KotIrnorgen...Cofight Vertical Rotary Etcher............*....................................................... 22 11. Aztec Products Custom Wet-Chemistry Line...state of the art in thick film hybrid fabrication methods, microelectronic fabrication and assembly, PC board fabrication, and electronic board assembly

  14. Inside Sandia, April 1996

    Energy Technology Data Exchange (ETDEWEB)

    Locke, T. [ed.

    1996-04-01

    Brief articles in this issue are entitled: New testing techniques, textiles on the information superhighway, and knowledge preservation; Structural health monitoring techniques and robust analysis tools assess aging and damaged structures; Sandia`s VCSELs (Vertical-Cavity Surface-Emitting Lasers): sparking a laser diode revolution; Fiber-optic instrumentation trims weeks off the wait for cervical cancer test results; DAMA (Demand Activated Manufacturing Architecture) project boosts competitiveness of US textile industry; SEAMIST (Science and Engineering Associates Membrane Instrumentation and Sampling Technique) cuts contamination cleanup costs; RePAVing the roads to the past (Relevant Point of Access Video); and Sandia receives DOE basic energy sciences award for sol-gel achievements.

  15. Sandia Laboratories energy programs

    Energy Technology Data Exchange (ETDEWEB)

    Lundergan, C.D.; Mead, P.L.; Gillespie, R.S. (eds.)

    1977-03-01

    As one of the multiprogram laboratories of the Energy Research and Development Administration, Sandia Laboratories applies its resources to a number of nationally important programs. About 75 percent of these resources are applied to research and development for national security programs having to do primarily with nuclear weapons--the principal responsibility of the Laboratories. The remaining 25 percent are applied to energy programs and energy-related activities, particularly those requiring resources that are also used in nuclear weapon and other national security programs. Examples of such energy programs and activities are research into nuclear fusion, protection of nuclear materials from theft or diversion, and the disposal of radioactive waste. A number of technologies and disciplines developed for the weapon program are immediately applicable for the development of various energy sources. Instruments developed to detect, measure, and record the detonation of nuclear devices underground, now being used to support the development of in-situ processing of coal and oil shale, are examples. The purpose of this report is to provide an overview of these and other energy programs being conducted by these laboratories in the development of economical and environmentally acceptable alternative energy sources. Energy programs are undertaken when they require capabilities used at the Laboratories for the weapon program, and when they have no adverse effect upon that primary mission. The parallel operation of weapon and energy activities allows optimum use of facilities and other resources.

  16. Characterization of the Effect of Au/Al Bondpad Corrosion on Microelectronic Device Reliability

    Energy Technology Data Exchange (ETDEWEB)

    BRAITHWAITE,JEFFREY W.; MICHAEL,JOSEPH R.; PETERSON,DAVID W.; ROBINSON,DAVID G.; SORENSEN,NEIL R.; STRIZICH,M.P.

    1999-10-07

    A methodology has been established to predict the effect of atmospheric corrosion on the reliability of plastic encapsulated microelectronic (PEM) devices. New experimental techniques were developed to directly characterize the Al/Au wirebond interface where corrosion primarily occurs. A deterministic empirical model describing wirebond degradation as a function of environmental conditions was generated. To demonstrate how this model can be used to determine corrosion effects on device reliability, a numerical simulation was performed on a three-lead voltage reference device. Surface reaction rate constants, environmental variables and the defect characteristics of the encapsulant were treated as distributed parameters. A Sandia-developed analytical framework (CRAX{trademark}) was used to include uncertainty in the analysis and directly calculate reliability.

  17. Sandia Laboratories technical capabilities: computation systems

    Energy Technology Data Exchange (ETDEWEB)

    1977-12-01

    This report characterizes the computation systems capabilities at Sandia Laboratories. Selected applications of these capabilities are presented to illustrate the extent to which they can be applied in research and development programs. 9 figures.

  18. Hermeticity testing of MEMS and microelectronic packages

    CERN Document Server

    Costello, Suzanne

    2013-01-01

    Packaging of microelectronics has been developing since the invention of the transistor in 1947. With the increasing complexity and decreasing size of the die, packaging requirements have continued to change. A step change in package requirements came with the introduction of the Micro-Electro-Mechanical System (MEMS) whereby interactions with the external environment are, in some cases, required.This resource is a rapid, definitive reference on hermetic packaging for the MEMS and microelectronics industry, giving practical guidance on traditional and newly developed test methods. This book in

  19. Microelectronics and Special Education. CET/MEP Information Sheet.

    Science.gov (United States)

    Council for Educational Technology, London (England).

    Used as an additional aid by the teacher, microelectronics can assist mentally and physically handicapped children to meet educational objectives that have been specifically agreed upon for the individual child. Microelectronics can help deaf children develop speech production, communication skills, and grammar and sentence construction;…

  20. Wire bonding in microelectronics

    CERN Document Server

    Harman, George G

    2010-01-01

    Wire Bonding in Microelectronics, Third Edition, has been thoroughly revised to help you meet the challenges of today's small-scale and fine-pitch microelectronics. This authoritative guide covers every aspect of designing, manufacturing, and evaluating wire bonds engineered with cutting-edge techniques. In addition to gaining a full grasp of bonding technology, you'll learn how to create reliable bonds at exceedingly high yields, test wire bonds, solve common bonding problems, implement molecular cleaning methods, and much more. Coverage includes: Ultrasonic bonding systems and technologies, including high-frequency systems Bonding wire metallurgy and characteristics, including copper wire Wire bond testing Gold-aluminum intermetallic compounds and other interface reactions Gold and nickel-based bond pad plating materials and problems Cleaning to improve bondability and reliability Mechanical problems in wire bonding High-yield, fine-pitch, specialized-looping, soft-substrate, and extreme-temperature wire bo...

  1. Hybrid microelectronic technology

    Science.gov (United States)

    Moran, P.

    Various areas of hybrid microelectronic technology are discussed. The topics addressed include: basic thick film processing, thick film pastes and substrates, add-on components and attachment methods, thin film processing, and design of thick film hybrid circuits. Also considered are: packaging hybrid circuits, automating the production of hybrid circuits, application of hybrid techniques, customer's view of hybrid technology, and quality control and assurance in hybrid circuit production.

  2. Microelectronic circuit design for energy harvesting systems

    CERN Document Server

    Di Paolo Emilio, Maurizio

    2017-01-01

    This book describes the design of microelectronic circuits for energy harvesting, broadband energy conversion, new methods and technologies for energy conversion. The author also discusses the design of power management circuits and the implementation of voltage regulators. Coverage includes advanced methods in low and high power electronics, as well as principles of micro-scale design based on piezoelectric, electromagnetic and thermoelectric technologies with control and conditioning circuit design. Provides a single-source reference to energy harvesting and its applications; Serves as a practical guide to microelectronics design for energy harvesting, with application to mobile power supplies; Enables readers to develop energy harvesting systems for wearable/mobile electronics.

  3. Microelectronic systems N2 checkbook

    CERN Document Server

    Vears, R E

    2013-01-01

    Microelectronic Systems N2 Checkbook provides coverage of the Business and Technician Education Council level NII unit in Microelectronic Systems. However, it can be regarded as a textbook in microelectronic systems for a much wider range of studies. The aim of this book is to provide a foundation in microelectronic systems hardware and software techniques. Each topic considered in the text is presented in a way that assumes in the reader only the knowledge attained in BTEC Information Technology Studies F, Engineering Fundamentals F, or equivalent. This book concentrates on the highly popular

  4. CEMA cooperation in microelectronics research, production

    Science.gov (United States)

    1984-03-01

    The assignments resulting from an agreement concerning multilateral specialization and cooperation among European socialist countries in the development and production of microelectronic components for computer technology are enumerated. Several areas which impact directly on the manufacture of large scale and very large scale integrated components are identified.

  5. Problems in CEMA microelectronic cooperation noted

    Science.gov (United States)

    Grzybowski, J.; Kusinski, J.

    1983-10-01

    The development and market trends of products, which use large scale integrated circuits are discussed. Products such as pocket calculators, electronic wrist watches, telephones, and automobiles are used to illustrate the economic results of market saturation with specialized integrated circuits. The status of microelectronics in socialist countries in Europe is addressed.

  6. Fast Qualification Methods for Microelectronic Packages

    NARCIS (Netherlands)

    Ma, X.

    2011-01-01

    This research aims at developing a knowledge based fast qualification method for moisture or thermally induced failure in microelectronic packages. Driven by the market competition and the need for shorter time to market, fast qualification tests are becoming more and more important for the industry

  7. Remote Microelectronics Fabrication Laboratory MEFLab

    Directory of Open Access Journals (Sweden)

    Jan Machotka

    2008-07-01

    Full Text Available Over the last decade, there has been a move towards using remote laboratories in engineering education. The majority of these laboratories are static, involving limited user-controlled mechanical movements. The University of South Australia has developed such a laboratory, called NetLab that has been successfully utilized for teaching both on-campus and transnational programs in electrical and electronics engineering. Following this success, we are now developing a remote laboratory for microelectronic fabrication, MEFLab. The first stage of the development is a remote laboratory for visual inspection and testing of electronic circuits directly on the silicon wafer under a microscope which is normally conducted in a cleanroom. The major challenge of this project is the accurate positioning of micro-probes remotely over the internet. This paper presents the details of the setup of this new remote laboratory, with a particular emphasis on the development of the hardware, software and graphical user interface.

  8. Adhesion in microelectronics

    CERN Document Server

    Mittal, K L

    2014-01-01

    This comprehensive book will provide both fundamental and applied aspects of adhesion pertaining to microelectronics in a single and easily accessible source. Among the topics to be covered include; Various theories or mechanisms of adhesionSurface (physical or chemical) characterization of materials as it pertains to adhesionSurface cleaning as it pertains to adhesionWays to improve adhesionUnraveling of interfacial interactions using an array of pertinent techniquesCharacterization of interfaces / interphasesPolymer-polymer adhesionMetal-polymer adhesion  (metallized polymers)Polymer adhesi

  9. Fighting blindness with microelectronics.

    Science.gov (United States)

    Zrenner, Eberhart

    2013-11-06

    There is no approved cure for blindness caused by degeneration of the photoreceptor cells of the retina. However, there has been encouraging progress with attempts to restore vision using microelectronic retinal implant devices. Yet many questions remain to be addressed. Where is the best location to implant multielectrode arrays? How can spatial and temporal resolution be improved? What are the best ways to ensure the safety and longevity of these devices? Will color vision be possible? This Perspective discusses the current state of the art of retinal implants and attempts to address some of the outstanding questions.

  10. Optical plasma microelectronic devices

    CERN Document Server

    Forati, Ebrahim; Dill, Thyler; Sievenpiper, Dan

    2015-01-01

    The semiconductor channel in conventional microelectronic devices was successfully replaced with an optically triggered gas plasma channel. The combination of DC and laser-induced gas ionizations controls the conductivity of the channel, enabling us to realize different electronic devices such as transistors, switches, modulators, etc. A special micro-scale metasurface was used to enhance the laser-gas interaction, as well as combining it with DC ionization properly. Optical plasma devices benefit form the advantages of plasma/vacuum electronic devices while preserving most of the integrablity of semiconductor based devices.

  11. III-V microelectronics

    CERN Document Server

    Nougier, JP

    1991-01-01

    As is well known, Silicon widely dominates the market of semiconductor devices and circuits, and in particular is well suited for Ultra Large Scale Integration processes. However, a number of III-V compound semiconductor devices and circuits have recently been built, and the contributions in this volume are devoted to those types of materials, which offer a number of interesting properties. Taking into account the great variety of problems encountered and of their mutual correlations when fabricating a circuit or even a device, most of the aspects of III-V microelectronics, from fundamental p

  12. Sandia energy titles

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, J.L. (ed.)

    1977-06-01

    This bibliography of reports, periodical arricles, and conference papers represents research carried out by Sandia Laboratories in energy and conservation. Within each of the approximately 300 entries, authors are listed alphabetically in each subject category. The following subjects are covered: Conservation, drilling technology, environment and safety, fossil energy, geothermal energy, nuclear energy, and solar energy. (MCW)

  13. Future trends in microelectronics journey into the unknown

    CERN Document Server

    Xu, Jimmy; Zaslavsky, Alexander

    2016-01-01

    Presents the developments in microelectronic-related fields, with comprehensive insight from a number of leading industry professionals. The book presents the future developments and innovations in the developing field of microelectronics. The book’s chapters contain contributions from various authors, all of whom are leading industry professionals affiliated either with top universities, major semiconductor companies, or government laboratories, discussing the evolution of their profession. A wide range of microelectronic-related fields are examined, including solid-state electronics, material science, optoelectronics, bioelectronics, and renewable energies. The topics covered range from fundamental physical principles, materials and device technologies, and major new market opportunities.

  14. Simulation and off-line programming at Sandia`s Intelligent Systems and Robotics Center

    Energy Technology Data Exchange (ETDEWEB)

    Xavier, P.G.; Fahrenholtz, J.C.; McDonald, M. [Sandia National Labs., Albuquerque, NM (United States). Intelligent Systems and Robotics Center] [and others

    1997-11-01

    One role of the Intelligent Robotics and System Center (ISRC) at Sandia National Laboratories is to address certain aspects of Sandia`s mission to design, manufacture, maintain, and dismantle nuclear weapon components. Hazardous materials, devices, and environments are often involved. Because of shrinking resources, these tasks must be accomplished with a minimum of prototyping, while maintaining high reliability. In this paper, the authors describe simulation, off-line programming/planning, and related tools which are in use, under development, and being researched to solve these problems at the ISRC.

  15. Biomedical engineering at Sandia National Laboratories

    Science.gov (United States)

    Zanner, Mary Ann

    1994-12-01

    The potential exists to reduce or control some aspects of the U.S. health care expenditure without compromising health care delivery by developing carefully selected technologies which impact favorably on the health care system. A focused effort to develop such technologies is underway at Sandia National Laboratories. As a DOE National Laboratory, Sandia possesses a wealth of engineering and scientific expertise that can be readily applied to this critical national need. Appropriate mechanisms currently exist to allow transfer of technology from the laboratory to the private sector. Sandia's Biomedical Engineering Initiative addresses the development of properly evaluated, cost-effective medical technologies through team collaborations with the medical community. Technology development is subjected to certain criteria including wide applicability, earlier diagnoses, increased efficiency, cost-effectiveness and dual-use. Examples of Sandia's medical technologies include a noninvasive blood glucose sensor, computer aided mammographic screening, noninvasive fetal oximetry and blood gas measurement, burn diagnostics and laser debridement, telerobotics and ultrasonic scanning for prosthetic devices. Sandia National Laboratories has the potential to aid in directing medical technology development efforts which emphasize health care needs, earlier diagnosis, cost containment and improvement of the quality of life.

  16. Sandia WIPP calibration traceability

    Energy Technology Data Exchange (ETDEWEB)

    Schuhen, M.D. [Sandia National Labs., Albuquerque, NM (United States); Dean, T.A. [RE/SPEC, Inc., Albuquerque, NM (United States)

    1996-05-01

    This report summarizes the work performed to establish calibration traceability for the instrumentation used by Sandia National Laboratories at the Waste Isolation Pilot Plant (WIPP) during testing from 1980-1985. Identifying the calibration traceability is an important part of establishing a pedigree for the data and is part of the qualification of existing data. In general, the requirement states that the calibration of Measuring and Test equipment must have a valid relationship to nationally recognized standards or the basis for the calibration must be documented. Sandia recognized that just establishing calibration traceability would not necessarily mean that all QA requirements were met during the certification of test instrumentation. To address this concern, the assessment was expanded to include various activities.

  17. Microelectronics improves power electronics

    Energy Technology Data Exchange (ETDEWEB)

    Diehl, R.

    1982-07-01

    The share of electric energy consumed by electric drives - called power current - can be used more efficiently by using power electronic regulating processes. Lower cost for power electronic components and progress in circuit technology are the decisive factors for the widespread use of regulating units. Microelectronics permit a cost-beneficial control of power regulating units, are made them more attractive for the user. Technical and economic attractivity of power electronic regulating processes have increased. These processes are mainly used for adjusting engine speed to the other process engineering parameters like pressure, output or speed. Optimization of power-current consuming processes are expected to achieve an energy saving potential of 15 TWh by the year 1995.

  18. Organic transistors in optical displays and microelectronic applications.

    Science.gov (United States)

    Gelinck, Gerwin; Heremans, Paul; Nomoto, Kazumasa; Anthopoulos, Thomas D

    2010-09-08

    Organic thin-film transistors (OTFTs) offer unprecedented opportunities for implementation in a broad range of technological applications spanning from large-volume microelectronics and optical displays to chemical and biological sensors. In this Progress Report, we review the application of organic transistors in the fields of flexible optical displays and microelectronics. The advantages associated with the use of OTFT technology are discussed with primary emphasis on the latest developments in the area of active-matrix electrophoretic and organic light-emitting diode displays based on OTFT backplanes and on the application of organic transistors in microelectronics including digital and analog circuits.

  19. SYNTHESIS AND APPLICATIONS OF NANOMATERIALS IN MICROELECTRONICS

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    IntroductionThe rapid development of microelectronics andtelecommunication industry in the last few years haspresented enormous opportllnities and challenges forchemical engineers and material scientists alike. Thefuture of all electronic devices is cheaped, lighted,smaller and more reliable. This development requiresfinely engineered materials.The field of engineering hi-tech materials is abroad and interdisciplinary area with extensiveworldwide research and development. Chemicalengineers, materials scient...

  20. Tiger Team assessment of the Sandia National Laboratories, Albuquerque

    Energy Technology Data Exchange (ETDEWEB)

    1991-05-01

    This report documents the Tiger Team Assessment of Sandia National Laboratories (SNL), Albuquerque, located in Albuquerque, New Mexico. SNL, Albuquerque, is operated by the Sandia Corporation (a wholly owned subsidiary of the American Telephone and Telegraph Company) for the US Department of Energy (DOE). The environmental assessment also included DOE tenant facilities at Ross Aviation, Albuquerque Microelectronics Operation, and the Central Training Academy. The assessment was conducted from April 15 to May 24, 1991, under the auspices of DOE's Office of Special Projects under the Assistant Secretary for Environment, Safety and Health (ES H). The assessment was comprehensive, encompassing ES H disciplines, management, self-assessments, and quality assurance; transportation; and waste management operations. Compliance with applicable federal, state, and local regulations; applicable DOE Orders; best management practices; and internal SNL, Albuquerque, requirements were assessed. In addition, an evaluation of the adequacy and effectiveness of DOE and SNL, Albuquerque management of ES H programs was conducted.

  1. Sandia's Z-Backlighter Laser Facility

    Science.gov (United States)

    Rambo, P.; Schwarz, J.; Schollmeier, M.; Geissel, M.; Smith, I.; Kimmel, M.; Speas, C.; Shores, J.; Armstrong, D.; Bellum, J.; Field, E.; Kletecka, D.; Porter, J.

    2016-12-01

    The Z-Backlighter Laser Facility at Sandia National Laboratories was developed to enable high energy density physics experiments in conjunction with the Z Pulsed Power Facility at Sandia National Laboratories, with an emphasis on backlighting. Since the first laser system there became operational in 2001, the facility has continually evolved to add new capability and new missions. The facility currently has several high energy laser systems including the nanosecond/multi-kilojoule Z-Beamlet Laser (ZBL), the sub-picosecond/kilojoule- class Z-Petawatt (ZPW) Laser, and the smaller nanosecond/100 J-class Chaco laser. In addition to these, the backlighting mission requires a regular stream of coated consumable optics such as debris shields and vacuum windows, which led to the development of the Sandia Optics Support Facility to support the unique high damage threshold optical coating needs described.

  2. Photoemission-based microelectronic devices

    Science.gov (United States)

    Forati, Ebrahim; Dill, Tyler J.; Tao, Andrea R.; Sievenpiper, Dan

    2016-11-01

    The vast majority of modern microelectronic devices rely on carriers within semiconductors due to their integrability. Therefore, the performance of these devices is limited due to natural semiconductor properties such as band gap and electron velocity. Replacing the semiconductor channel in conventional microelectronic devices with a gas or vacuum channel may scale their speed, wavelength and power beyond what is available today. However, liberating electrons into gas/vacuum in a practical microelectronic device is quite challenging. It often requires heating, applying high voltages, or using lasers with short wavelengths or high powers. Here, we show that the interaction between an engineered resonant surface and a low-power infrared laser can cause enough photoemission via electron tunnelling to implement feasible microelectronic devices such as transistors, switches and modulators. The proposed photoemission-based devices benefit from the advantages of gas-plasma/vacuum electronic devices while preserving the integrability of semiconductor-based devices.

  3. RF and microwave microelectronics packaging II

    CERN Document Server

    Sturdivant, Rick

    2017-01-01

    Reviews RF, microwave, and microelectronics assembly process, quality control, and failure analysis Bridges the gap between low cost commercial and hi-res RF/Microwave packaging technologies Engages in an in-depth discussion of challenges in packaging and assembly of advanced high-power amplifiers This book presents the latest developments in packaging for high-frequency electronics. It is a companion volume to “RF and Microwave Microelectronics Packaging” (2010) and covers the latest developments in thermal management, electrical/RF/thermal-mechanical designs and simulations, packaging and processing methods, and other RF and microwave packaging topics. Chapters provide detailed coverage of phased arrays, T/R modules, 3D transitions, high thermal conductivity materials, carbon nanotubes and graphene advanced materials, and chip size packaging for RF MEMS. It appeals to practicing engineers in the electronic packaging and high-frequency electronics domain, and to academic researchers interested in underst...

  4. Sandia`s computer support units: The first three years

    Energy Technology Data Exchange (ETDEWEB)

    Harris, R.N. [Sandia National Labs., Albuquerque, NM (United States). Labs. Computing Dept.

    1997-11-01

    This paper describes the method by which Sandia National Laboratories has deployed information technology to the line organizations and to the desktop as part of the integrated information services organization under the direction of the Chief Information officer. This deployment has been done by the Computer Support Unit (CSU) Department. The CSU approach is based on the principle of providing local customer service with a corporate perspective. Success required an approach that was both customer compelled at times and market or corporate focused in most cases. Above all, a complete solution was required that included a comprehensive method of technology choices and development, process development, technology implementation, and support. It is the authors hope that this information will be useful in the development of a customer-focused business strategy for information technology deployment and support. Descriptions of current status reflect the status as of May 1997.

  5. Sandia Technology: Engineering and science accomplishments, February 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-02-01

    Sandia National Laboratories is one of the Department of Energy`s primary research and development laboratories. Our essential mission is to support the national interests of the US in defense, energy, and the environment. Managed by Martin Marietta Corporation for DOE, Sandia focuses its resources on problems of national interest that require the integration of science and technology for their solution. We all hope that this period of sweeping alterations in international affairs will result in a successful transition from the Cold War to a period of sustainable global security and prosperity. In the meantime, our nation`s interests are best served by continued commitment to Sandia`s traditional responsibilities. Nonetheless, as momentous developments are reshaping the world, Sandia is also changing from its beginning as a closed operation concentrating on classified defense programs, Sandia has become a more accessible resource that focuses on research and development partnerships with industry and universities as a way to ensure continued success in DOE`s evolving core mission area of nuclear weapons, energy, environment, and the basis sciences. Through these collaborative efforts, Sandia and its partners are also benefiting the economic competitiveness of our nation. Sandia places a special emphasis on working with small businesses as both technology transfer partners and suppliers of goods and services. We are also reaching out the the larger community surrounding Sandia, striving to provide technological solution and accurate information to meet community needs. We believe that the dialogue we are creating will benefit Sandia, the community, and the nation. Our goal is to render `` exceptional service in the national interest`` by returning maximum value on the investment in the labs. As you review this document, look for new ways in which Sandia can contribute to the solution of problems facing our nation.

  6. Surface analysis in microelectronics.

    Science.gov (United States)

    Pignataro, S

    1995-10-01

    The contribution given by surface analysis to solve some problems encountered in the production of electronic power devices have been discussed. Mainly two types of problems have been faced. One of these deal with interfacial chemistry. Three examples have been investigated. The first applies to the improvement of the quality and the reliability of plastic packages through the optimization of the resin/metal and resin/die adhesion. The second relies to the adhesion between polyimide and silicon nitride used in the multilevel technology. The third example refers to the so called die-attach process and related problems. Another area of interest in microelectronics is that of the erosion of various types of surfaces and the possibility of wrong etching. A few examples of the application of surface analytical techniques for these problems will be presented. XPS and SIMS working in imaging and multipoint analysis mode, scanning acoustic microscopy, contact angle measurements as well as peeling and tensile strength measurements are the main tools used to obtain useful data.

  7. Sandia National Laboratories Institutional Plan: FY 1996--2001

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    Sandia`s Institutional Plan is by necessity a large document. As their missions have grown and diversified over the past decades, the variety of technical and site activities has increased. The programs and activities described here cover an enormous breadth of scientific and technological effort--from the creation of new materials to the development of a Sandia-wide electronic communications system. Today, there are three major themes that greatly influence this work. First, every federally funded institution is being challenged to find ways to become more cost effective, as the US seeks to reduce the deficit and achieve a balanced federal spending plan. Sandia is evaluating its business and operational processes to reduce the overall costs. Second, in response to the Galvin Task Force`s report ``Alternative Futures for the Department of Energy National Laboratories``, Sandia and the Department of Energy are working jointly to reduce the burden of administrative and compliance activities in order to devote more of the total effort to their principal research and development missions. Third, they are reevaluating the match between their missions and the programs they will emphasize in the future. They must demonstrate that Sandia`s roles--in national security, energy security, environmental integrity, and national scientific and technology agenda support--fit their special capabilities and skills and thus ensure their place in these missions for the longer planning horizon. The following areas are covered here: Sandia`s mission; laboratory directives; programmatic activities; technology partnerships and commercialization; Sandia`s resources; and protecting resources and the community.

  8. Microelectronics from fundamentals to applied design

    CERN Document Server

    Di Paolo Emilio, Maurizio

    2016-01-01

    This book serves as a practical guide for practicing engineers who need to design analog circuits for microelectronics.  Readers will develop a comprehensive understanding of the basic techniques of analog modern electronic circuit design, discrete and integrated, application as sensors and control and data acquisition systems,and techniques of PCB design.  ·         Describes fundamentals of microelectronics design in an accessible manner; ·         Takes a problem-solving approach to the topic, offering a hands-on guide for practicing engineers; ·         Provides realistic examples to inspire a thorough understanding of system-level issues, before going into the detail of components and devices; ·         Uses a new approach and provides several skills that help engineers and designers retain key and advanced concepts.

  9. Laser processing of ceramics for microelectronics manufacturing

    Science.gov (United States)

    Sposili, Robert S.; Bovatsek, James; Patel, Rajesh

    2017-03-01

    Ceramic materials are used extensively in the microelectronics, semiconductor, and LED lighting industries because of their electrically insulating and thermally conductive properties, as well as for their high-temperature-service capabilities. However, their brittleness presents significant challenges for conventional machining processes. In this paper we report on a series of experiments that demonstrate and characterize the efficacy of pulsed nanosecond UV and green lasers in machining ceramics commonly used in microelectronics manufacturing, such as aluminum oxide (alumina) and aluminum nitride. With a series of laser pocket milling experiments, fundamental volume ablation rate and ablation efficiency data were generated. In addition, techniques for various industrial machining processes, such as shallow scribing and deep scribing, were developed and demonstrated. We demonstrate that lasers with higher average powers offer higher processing rates with the one exception of deep scribes in aluminum nitride, where a lower average power but higher pulse energy source outperformed a higher average power laser.

  10. NDE applications in microelectronic industries

    Science.gov (United States)

    Meyendorf, N.; Oppermann, M.; Krueger, P.; Roellig, M.; Wolter, K. J.

    2016-04-01

    New concepts in assembly technology boost our daily life in an unknown way. High end semiconductor industry today deals with functional structures down to a few nanometers. ITRS roadmap predicts an ongoing decrease of the "DRAM half pitch" over the next decade. Packaging of course is not intended to realize pitches at the nanometer scale, but has to face the challenges of integrating such semiconductor devices with smallest pitch and high pin counts into systems. Advanced techniques of nondestructive evaluation (NDE) with resolutions in volume better than 1 micrometer vixen size are urgently needed for the safety and reliability of electronic systems, especially those that are used in long living applications. The development speed of integrated circuits is still very high and is not expected to decrease in the next future. The integration density of microelectronic devices is increasing, the dimensions become smaller and the number of I/O's is getting higher. The development of new types of packages must be done with respect to reliability issues. Potential damage sources must be identified and finally avoided in the new packages. In power electronics production the condition monitoring receives a lot of interest to avoid electrical shortcuts, dead solder joints and interface cracking. It is also desired to detect and characterize very small defects like transportation phenomenon or Kirkendall voids. For this purpose, imaging technologies with resolutions in the sub-micron range are required.

  11. Advances in Microelectronics for Implantable Medical Devices

    Directory of Open Access Journals (Sweden)

    Andreas Demosthenous

    2014-01-01

    Full Text Available Implantable medical devices provide therapy to treat numerous health conditions as well as monitoring and diagnosis. Over the years, the development of these devices has seen remarkable progress thanks to tremendous advances in microelectronics, electrode technology, packaging and signal processing techniques. Many of today’s implantable devices use wireless technology to supply power and provide communication. There are many challenges when creating an implantable device. Issues such as reliable and fast bidirectional data communication, efficient power delivery to the implantable circuits, low noise and low power for the recording part of the system, and delivery of safe stimulation to avoid tissue and electrode damage are some of the challenges faced by the microelectronics circuit designer. This paper provides a review of advances in microelectronics over the last decade or so for implantable medical devices and systems. The focus is on neural recording and stimulation circuits suitable for fabrication in modern silicon process technologies and biotelemetry methods for power and data transfer, with particular emphasis on methods employing radio frequency inductive coupling. The paper concludes by highlighting some of the issues that will drive future research in the field.

  12. Energy technologies at Sandia National Laboratories: Past, Present, Future

    Energy Technology Data Exchange (ETDEWEB)

    1989-08-01

    We at Sandia first became involved with developing energy technology when the nation initiated its push toward energy independence in the early 1970s. That involvement continues to be strong. In shaping Sandia's energy programs for the 1990s, we will build on our track record from the 70s and 80s, a record outlined in this publication. It contains reprints of three issues of Sandia's Lab News that were devoted to our non-nuclear energy programs. Together, they summarize the history, current activities, and future of Sandia's diverse energy concerns; hence my desire to see them in one volume. Written in the fall of 1988, the articles cover Sandia's extremely broad range of energy technologies -- coal, oil and gas, geothermal, solar thermal, photovoltaics, wind, rechargeable batteries, and combustion.

  13. Sandia concentrator array testing experiences

    Science.gov (United States)

    Gerwin, H. J.; Rogers, C. B.; Beavis, L. C.

    An assortment of PV concentrator modules and arrays have been tested and evaluated at the Sandia outdoor test facility. These test items include actively-cooled parabolic reflector and linear Fresnel lens concentrators, and actively- and passively-cooled point focus collectors. Maximum power efficiencies were measured over a range of sunlight intensities and cell temperatures, then a linear equation relating efficiency to cell temperature and insolation was developed for each module and array by using a multiple linear regression analysis technique on the data. An evaluation of the suitability of Polyvinyl-Butyral (PVB) as a material used to laminate solar cells to glass is presented. Some general observations are made on the accuracy of tracking systems, and the maintenance of these systems.

  14. Microelectronics: Their Implications for Education and Training.

    Science.gov (United States)

    Audiovisual Instruction, 1979

    1979-01-01

    This two-part article indicates some probable characteristics of the microelectronics in the future and assesses implications of the microelectronics revolution for the methods and systems currently used in teaching and training. (CMV)

  15. Apparatus for assembly of microelectronic devices

    Energy Technology Data Exchange (ETDEWEB)

    Okandan, Murat; Nielson, Gregory N.; Cruz-Campa, Jose Luis; Lavin, Judith Maria; Resnick, Paul J.

    2017-09-12

    An apparatus including a carrier substrate configured to move a microelectronic device. The apparatus further includes a rotatable body configured to receive the microelectronic device. Additionally, the apparatus includes a second substrate configured to receive the microelectronic device from the rotatable body.

  16. Microelectronics in Education--A Changing Future.

    Science.gov (United States)

    Humphries, Chris

    1985-01-01

    Describes major program activities of Microelectronics Education Programme (MEP) for England, Wales, and Northern Ireland, which is designed to help schools prepare children for society with microelectronics. The core elements and potential consequences of the Microelectronics Support Unit, a follow-up to MEP which will conclude activities in…

  17. Microelectronics and Computers in Medicine.

    Science.gov (United States)

    Meindl, James D.

    1982-01-01

    The use of microelectronics and computers in medicine is reviewed, focusing on medical research; medical data collection, storage, retrieval, and manipulation; medical decision making; computed tomography; ultrasonic imaging; role in clinical laboratories; and use as adjuncts for diagnostic tests, monitors of critically-ill patients, and with the…

  18. Fundamentals of Microelectronics Processing (VLSI).

    Science.gov (United States)

    Takoudis, Christos G.

    1987-01-01

    Describes a 15-week course in the fundamentals of microelectronics processing in chemical engineering, which emphasizes the use of very large scale integration (VLSI). Provides a listing of the topics covered in the course outline, along with a sample of some of the final projects done by students. (TW)

  19. Microelectronic test structures for CMOS technology

    CERN Document Server

    Ketchen, Mark B

    2011-01-01

    Microelectronic Test Structures for CMOS Technology and Products addresses the basic concepts of the design of test structures for incorporation within test-vehicles, scribe-lines, and CMOS products. The role of test structures in the development and monitoring of CMOS technologies and products has become ever more important with the increased cost and complexity of development and manufacturing. In this timely volume, IBM scientists Manjul Bhushan and Mark Ketchen emphasize high speed characterization techniques for digital CMOS circuit applications and bridging between circuit performance an

  20. Data encryption standard ASIC design and development report.

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, Perry J.; Pierson, Lyndon George; Witzke, Edward L.

    2003-10-01

    This document describes the design, fabrication, and testing of the SNL Data Encryption Standard (DES) ASIC. This device was fabricated in Sandia's Microelectronics Development Laboratory using 0.6 {micro}m CMOS technology. The SNL DES ASIC was modeled using VHDL, then simulated, and synthesized using Synopsys, Inc. software and finally IC layout was performed using Compass Design Automation's CAE tools. IC testing was performed by Sandia's Microelectronic Validation Department using a HP 82000 computer aided test system. The device is a single integrated circuit, pipelined realization of DES encryption and decryption capable of throughputs greater than 6.5 Gb/s. Several enhancements accommodate ATM or IP network operation and performance scaling. This design is the latest step in the evolution of DES modules.

  1. Sandia Laboratories technical capabilities: design, definition, and fabrication

    Energy Technology Data Exchange (ETDEWEB)

    1976-12-01

    This report characterizes the design definition and fabrication capabilities at Sandia Laboratories. Selected applications of these capabilities are presented to illustrate the extent to which they can be applied in research and development programs. 13 figures.

  2. Biological restoration of major transportation facilities domestic demonstration and application project (DDAP): technology development at Sandia National Laboratories.

    Energy Technology Data Exchange (ETDEWEB)

    Ramsey, James L., Jr. (.,; .); Melton, Brad; Finley, Patrick; Brockman, John; Peyton, Chad E.; Tucker, Mark David; Einfeld, Wayne; Griffith, Richard O.; Brown, Gary Stephen; Lucero, Daniel A.; Betty, Rita G.; McKenna, Sean Andrew; Knowlton, Robert G.; Ho, Pauline

    2006-06-01

    The Bio-Restoration of Major Transportation Facilities Domestic Demonstration and Application Program (DDAP) is a designed to accelerate the restoration of transportation nodes following an attack with a biological warfare agent. This report documents the technology development work done at SNL for this DDAP, which include development of the BROOM tool, an investigation of surface sample collection efficiency, and a flow cytometry study of chlorine dioxide effects on Bacillus anthracis spore viability.

  3. Market Assessment and Commercialization Strategy for the Radial Sandia Cooler

    Energy Technology Data Exchange (ETDEWEB)

    Goetzler, William [Navigant Consulting, Inc., Burlington, MA (United States); Shandross, Richard [Navigant Consulting, Inc., Burlington, MA (United States); Weintraub, Daniel [Navigant Consulting, Inc., Burlington, MA (United States); Young, Jim [Navigant Consulting, Inc., Burlington, MA (United States)

    2014-02-01

    This market assessment and commercialization report characterizes and assesses the market potential of the rotating heat exchanger technology developed at Sandia National Laboratories (SNL), known as the Radial Sandia Cooler. The RSC is a novel, motor-driven, rotating, finned heat exchanger technology. The RSC was evaluated for the residential, commercial, industrial, and transportation markets. Recommendations for commercialization were made based on assessments of the prototype RSC and the Sandia Cooler technology in general, as well as an in-depth analysis of the six most promising products for initial RSC commercialization.

  4. Vibration control for precision manufacturing at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Hinnerichs, T.; Martinez, D. [Sandia National Labs., Albuquerque, NM (United States). Structural Dynamics and Vibration Control Dept.

    1995-04-01

    Sandia National Laboratories performs R and D in structural dynamics and vibration suppression for precision applications in weapon systems, space, underwater, transportation and civil structures. Over the last decade these efforts have expanded into the areas of active vibration control and ``smart`` structures and material systems. In addition, Sandia has focused major resources towards technology to support weapon product development and agile manufacturing capability for defense and industrial applications. This paper will briefly describe the structural dynamics modeling and verification process currently in place at Sandia that supports vibration control and some specific applications of these techniques to manufacturing in the areas of lithography, machine tools and flexible robotics.

  5. Compilation of Sandia Laboratories technical capabilities

    Energy Technology Data Exchange (ETDEWEB)

    Lundergan, C. D.; Mead, P. L. [eds.

    1975-11-01

    This report is a compilation of 17 individual documents that together summarize the technical capabilities of Sandia Laboratories. Each document in this compilation contains details about a specific area of capability. Examples of application of the capability to research and development problems are provided. An eighteenth document summarizes the content of the other seventeen. Each of these documents was issued with a separate report number (SAND 74-0073A through SAND 74-0091, except -0078). (RWR)

  6. 3D microelectronic packaging from fundamentals to applications

    CERN Document Server

    Goyal, Deepak

    2017-01-01

    This volume provides a comprehensive reference for graduate students and professionals in both academia and industry on the fundamentals, processing details, and applications of 3D microelectronic packaging, an industry trend for future microelectronic packages. Chapters written by experts cover the most recent research results and industry progress in the following areas: TSV, die processing, micro bumps, direct bonding, thermal compression bonding, advanced materials, heat dissipation, thermal management, thermal mechanical modeling, quality, reliability, fault isolation, and failure analysis of 3D microelectronic packages. Numerous images, tables, and didactic schematics are included throughout. This essential volume equips readers with an in-depth understanding of all aspects of 3D packaging, including packaging architecture, processing, thermal mechanical and moisture related reliability concerns, common failures, developing areas, and future challenges, providing insights into key areas for future resea...

  7. Kovar Micro Heat Pipe Substrates for Microelectronic Cooling

    Energy Technology Data Exchange (ETDEWEB)

    Benson, David A.; Burchett, Steven N.; Kravitz, Stanley H.; Robino, Charles V.; Schmidt, Carrie; Tigges, Chris P.

    1999-04-01

    We describe the development of a new technology for cooling microelectronics. This report documents the design, fabrication, and prototype testing of micro scale heat pipes embedded in a flat plate substrate or heat spreader. A thermal model tuned to the test results enables us to describe heat transfer in the prototype, as well as evaluate the use of this technology in other applications. The substrate walls are Kovar alloy, which has a coefficient of thermal expansion close to that of microelectronic die. The prototype designs integrating micro heat pipes with Kovar enhance thermal conductivity by more than a factor of two over that of Kovar alone, thus improving the cooling of micro-electronic die.

  8. The Wales Region: Microelectronics Education to the Mid Eighties.

    Science.gov (United States)

    Taylor, Lionel

    1982-01-01

    Discusses developments which should occur in the Wales region by the end of the Microelectronics Education Programme (1984). Indicates that a major curriculum project has been started to enable developments in information technology to be reflected in classrooms, focusing on the production of software and resource materials. (Author/JN)

  9. Application of ionizing radiation processing in biomedical engineering and microelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Hongfej, H.; Jilan, W.

    1988-01-01

    The applied radiation chemistry has made great contributions to the development of polymeric industrial materials by the characteristics reaction means such as crosslinking, graft copolymerization and low-temperature or solid-phase polymerization, and become a important field on peaceful use of atomic energy. A brief review on the applications of ionizing radiation processing in biomedical engineering and microelectronics is presented. The examples of this technique were the studies on biocompatible and biofunctional polymers for medical use and on resists of lithography in microelectronics.

  10. Study on the evaluation of aerospace microelectronic industry

    Institute of Scientific and Technical Information of China (English)

    江帆; 陈荣秋

    2004-01-01

    Aerospace microelectronic technology has become the core competence of aerospace technology. For evaluating the aerospace microelectronic industry, it is necessary to change descriptive language of goal to quantitative index that can be measured. Knowing quantified goals or tree structure and array of general goal system, with certain algorithm and processing each corresponding list or array, we can bring out a quantified general goal value. The multi-objective (multi-attribute) evaluation method and the relevant weight sum algorithm have been adopted to quantitatively evaluate and forecast the developing state of the industry. A practical example illustrates that the applied decision technique and the algorithm are feasible and effective.

  11. Sandia National Laboratories corporate mentor program : program review, May 2004.

    Energy Technology Data Exchange (ETDEWEB)

    Tibbetts, Tiffany; Tarro, Talitha; Dudeck, William; Bristol, Colette; Stephens, Jim

    2005-01-01

    The Sandia National Laboratories Corporate Mentor Program provides a mechanism for the development and retention of Sandia's people and knowledge. The relationships formed among staff members at different stages in their careers offer benefits to all. These relationships can provide experienced employees with new ideas and insight and give less experienced employees knowledge of Sandia's culture, strategies, and programmatic direction. The program volunteer coordinators are dedicated to the satisfaction of the participants, who come from every area of Sandia. Since its inception in 1995, the program has sustained steady growth and excellent customer satisfaction. This report summarizes the accomplishments, activities, enhancements, and evaluation data for the Corporate Mentor Program for the 2003/2004 program year ending May 1, 2004.

  12. Microelectronics packaging research directions for aerospace applications

    Science.gov (United States)

    Galbraith, L.

    2003-01-01

    The Roadmap begins with an assessment of needs from the microelectronics for aerospace applications viewpoint. Needs Assessment is divided into materials, packaging components, and radiation characterization of packaging.

  13. 1998 Annual Site Environmental Report Sandia National Laboratories, Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Duncan, D.K.; Fink, C.H.; Sanchez, R.V.

    1999-09-01

    Sandia National Laboratories/New Mexico (SNL/NM) is operated in support of the US Department of Energy (DOE) mission to provide weapon component technology and hardware for national security needs. SNL/NM also conducts fundamental research and development to advance technology in energy research, computer science, waste management, microelectronics, materials science, and transportation safety for hazardous and nuclear components. In support of SNL's mission, the Environment, Safety and Health (ES&H) Center and the Environmental Restoration (ER) Project at SNL/NM have established extensive environmental programs to assist SNL's line organizations in meeting all applicable local, State, and Federal environmental regulations and DOE requirements. This annual report for calendar year 1998 (CY98) summarizes the compliance status of environmental regulations applicable to SNL site operations. Environmental program activities include terrestrial surveillance; ambient air and meteorological monitoring hazardous, radioactive, and solid waste management; pollution prevention and waste minimization; environmental remediation; oil and chemical spill prevention; and National Environmental Policy Act (NEPA) activities. This report has been prepared in compliance with DOE Order 5400.1, General Environmental Protection Program (DOE 1990).

  14. Speculations on the Social Effects of New Microelectronics Technology.

    Science.gov (United States)

    Cherns, A. B.

    1980-01-01

    Examines the implications of the reduced importance of employment for individuals, for enterprises (work conditions, management styles), trade unions (with a more political than industrial role), and the conservation of resources, concluding with a brief look at the possible benefits of microelectronics for the developing countries. (CT)

  15. Sandia Combustion Research: Technical review

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    This report contains reports from research programs conducted at the Sandia Combustion Research Facility. Research is presented under the following topics: laser based diagnostics; combustion chemistry; reacting flow; combustion in engines and commercial burners; coal combustion; and industrial processing. Individual projects were processed separately for entry onto the DOE databases.

  16. Educational Implications of Microelectronics and Microprocessors.

    Science.gov (United States)

    Harris, N. D. C., Ed.

    This conference report explores microelectronic technology, its effect on educational methods and objectives, and its implications for educator responsibilities. Two main areas were considered: the significance of the likely impact of the large scale introduction of microprocessors and microelectronics on commercial and industrial processes, the…

  17. Biomimetic Microelectronics for Regenerative Neuronal Cuff Implants.

    Science.gov (United States)

    Karnaushenko, Daniil; Münzenrieder, Niko; Karnaushenko, Dmitriy D; Koch, Britta; Meyer, Anne K; Baunack, Stefan; Petti, Luisa; Tröster, Gerhard; Makarov, Denys; Schmidt, Oliver G

    2015-11-18

    Smart biomimetics, a unique class of devices combining the mechanical adaptivity of soft actuators with the imperceptibility of microelectronics, is introduced. Due to their inherent ability to self-assemble, biomimetic microelectronics can firmly yet gently attach to an inorganic or biological tissue enabling enclosure of, for example, nervous fibers, or guide the growth of neuronal cells during regeneration.

  18. Surface reactions in microelectronics process technology.

    Science.gov (United States)

    Levitin, Galit; Hess, Dennis W

    2011-01-01

    Current integrated circuit (IC) manufacturing consists of more than 800 process steps, nearly all of which involve reactions at surfaces that significantly impact device yield and performance. From initial surface preparation through film deposition, patterning, etching, residue removal, and metallization, an understanding of surface reactions and interactions is critical to the successful continuous scaling, yield, and reliability of electronic devices. In this review, some of the most important surface reactions that drive the development of microelectronic device fabrication are described. The reactions discussed do not constitute comprehensive coverage of this topic in IC manufacture but have been selected to demonstrate the importance of surface/interface reactions and interactions in the development of new materials, processing sequences, and process integration challenges. Specifically, the review focuses on surface reactions related to surface cleaning/preparation, semiconductor film growth, dielectric film growth, metallization, and etching (dry and wet).

  19. Sandia capabilities for the measurement, characterization, and analysis of heliostats for CSP.

    Energy Technology Data Exchange (ETDEWEB)

    Andraka, Charles E.; Christian, Joshua Mark; Ghanbari, Cheryl M.; Gill, David Dennis; Ho, Clifford Kuofei; Kolb, William J.; Moss, Timothy A.; Smith, Edward J.; Yellowhair, Julius

    2013-07-01

    The Concentrating Solar Technologies Organization at Sandia National Laboratories has a long history of performing important research, development, and testing that has enabled the Concentrating Solar Power Industry to deploy full-scale power plants. Sandia continues to pursue innovative CSP concepts with the goal of reducing the cost of CSP while improving efficiency and performance. In this pursuit, Sandia has developed many tools for the analysis of CSP performance. The following capabilities document highlights Sandias extensive experience in the design, construction, and utilization of large-scale testing facilities for CSP and the tools that Sandia has created for the full characterization of heliostats. Sandia has extensive experience in using these tools to evaluate the performance of novel heliostat designs.

  20. Statement of Work Electrical Energy Storage System Installation at Sandia National Laboratories.

    Energy Technology Data Exchange (ETDEWEB)

    Schenkman, Benjamin L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-03-01

    Sandia is seeking to procure a 1 MWh energy storage system. It will be installed at the existing Energy Storage Test Pad, which is located at Sandia National Laboratories in Albuquerque, New Mexico. This energy storage system will be a daily operational system, but will also be used as a tool in our Research and development work. The system will be part of a showcase of Sandia distributed energy technologies viewed by many distinguished delegates.

  1. Nanocharacterization Challenges in a Changing Microelectronics Landscape

    Science.gov (United States)

    Brilloüt, Michel

    2011-11-01

    As the microelectronics industry enters the "nano"-era new challenges emerge. Traditional scaling of the MOS transistor faces major obstacles in fulfilling "Moore's law". New features like strain and new materials (e.g. high k—metal gate stack) are introduced in order to sustain performance increases. For a better electrostatic control, devices will use the third dimension, e.g., in gate-all-around nanowire structures. Due to the escalating cost and complexity of sub-28 nm technologies fewer industrial players can afford the development and production of advanced CMOS processes and many companies acknowledge the fact that the value in products can also be obtained in using more diversified non-digital technologies (the so-called "More-than-Moore" domain). This evolving landscape brings new requirements—discussed in this paper—in terms of physical characterization of technologies and devices.

  2. Overview of Sandia's electric vehicle battery program

    Science.gov (United States)

    Clark, R. P.

    1993-11-01

    Sandia National Laboratories is actively involved in several projects which are part of an overall Electric Vehicle Battery Program. Part of this effort is funded by the United States Department of Energy/Office of Transportation Technologies (DOE/OTT) and the remainder is funded through the United States Advanced Battery Consortium (USABC). DOE/OTT supported activities include research and development of zinc/air and sodium/sulfur battery technologies as well as double layer capacitor (DLC) R&D. Projects in the USABC funded work include lithium/polymer electrolyte (LPE) R&D, sodium/sulfur activities and battery test and evaluation.

  3. Sandia technology engineering and science accomplishments

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    Sandia is a DOE multiprogram engineering and science laboratory with major facilities at Albuquerque, New Mexico, and Livermore, California, and a test range near Tonapah, Nevada. We have major research and development responsibilities for nuclear weapons, arms control, energy, the environment, economic competitiveness, and other areas of importance to the needs of the nation. Our principal mission is to support national defense policies by ensuring that the nuclear weapon stockpile meets the highest standards of safety, reliability, security, use control, and military performance. Selected unclassified technical activities and accomplishments are reported here. Topics include advanced manufacturing technologies, intelligent machines, computational simulation, sensors and instrumentation, information management, energy and environment, and weapons technology.

  4. Materials science in microelectronics II the effects of structure on properties in thin films

    CERN Document Server

    Machlin, Eugene

    2005-01-01

    The subject matter of thin-films - which play a key role in microelectronics - divides naturally into two headings: the processing / structure relationship, and the structure / properties relationship. Part II of 'Materials Science in Microelectronics' focuses on the latter of these relationships, examining the effect of structure on the following: Electrical properties Magnetic properties Optical properties Mechanical properties Mass transport properties Interface and junction properties Defects and properties Captures the importance of thin films to microelectronic development Examines the cause / effect relationship of structure on thin film properties.

  5. Physical Limitations in Lithography for Microelectronics.

    Science.gov (United States)

    Flavin, P. G.

    1981-01-01

    Describes techniques being used in the production of microelectronics kits which have replaced traditional optical lithography, including contact and optical projection printing, and X-ray and electron beam lithography. Also includes limitations of each technique described. (SK)

  6. Health issues in the microelectronics industry.

    Science.gov (United States)

    LaDou, J

    1986-01-01

    Since 1948, when microelectronics entered the American industrial scene, the rapid growth and advancing technology of the industry has caused production facilities to be spread throughout most industrialized areas in the United States. It is now speculated that microelectronics production will be the fourth largest industry in the United States by the end of the century. This article addresses the questions raised about the safety of this industry both for its workers and for the communities in which production facilities are located.

  7. Sandia SWiFT Site Safe Work Planning Manual.

    Energy Technology Data Exchange (ETDEWEB)

    White, Jonathan

    2016-02-01

    The Department of Energy's Scaled Wind Farm Technology (SWiFT) facility provides research site with multiple wind turbines at a scale useful for the experimental study of wake dynamics, advanced rotor development, turbine control, and advanced sensing for production-scale wind farms. Safety of workers and the public is the top and overriding priority at SWiFT. Central to safe operations are formal planning processes . This manual provides an overview of test planning and work planning processes and requirements in adherence with the Sandia corporate Engineered Safety Work Planning and Control process. It is required reading for all SWiFT site staff, Sandia workers, and collaborators who oversee, conduct, or participate in test activities or who are involved in modifying Sandia SWiFT site assets.

  8. Double Shock Experiments on the Sandia Z Machine

    Science.gov (United States)

    Hanshaw, Heath; Knudson, Marcus; Desjarlais, Michael; Lemke, Ray

    2011-06-01

    The double shock layered high-velocity flyer plate is one new capability being developed on Sandia's Z machine. With this technique, dynamic material data at high energy densities can be obtained at points in phase space which lie neither on principal Hugoniots nor on quasi-isentropic ramp curves. For example, the hypothesized HCP to BCC phase transition in beryllium can be measured, as can the high pressure melt curve. Another example is a postulated refreeze of tantalum. We discuss the double shock experiments being performed on Z, including accessible conditions, design and experimental methods, and analysis of results. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  9. HyMARC (Sandia) Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Allendorf, Mark D. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Stavila, Vitalie [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Klebanoff, Leonard E. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Kolasinski, Robert [Sandia National Lab. (SNL-CA), Livermore, CA (United States); El Gabaly Marquez, Farid [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Zhou, Xiaowang [Sandia National Lab. (SNL-CA), Livermore, CA (United States); White, James Lawrence [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2017-07-01

    The Sandia HyMARC team continued its development of new synthetic, modeling, and diagnostic tools that are providing new insights into all major classes of storage materials, ranging from relatively simple systems such as PdHx and MgH2, to exceptionally complex ones, such as the metal borohydrides, as well as materials thought to be very well-understood, such as Ti-doped NaAlH4. This unprecedented suite of capabilities, capable of probing all relevant length scales within storage materials, is already having a significant impact, as they are now being used by both Seedling projects and collaborators at other laboratories within HyMARC. We expect this impact to grow as new Seedling projects begin and through collaborations with other scientists outside HyMARC. In the coming year, Sandia efforts will focus on the highest impact problems, in coordination with the other HyMARC National Laboratory partners, to provide the foundational science necessary to accelerate the discovery of new hydrogen storage materials.

  10. Sandia combustion research program: Annual report, 1987

    Energy Technology Data Exchange (ETDEWEB)

    Palmer, R.E.; Sanders, B.R.; Ivanetich, C.A. (eds.)

    1988-01-01

    More than a decade ago, in response to a national energy crisis, Sandia proposed to the US Department of Energy a new, ambitious program in combustion research. Our strategy was to apply the rapidly increasing capabilities in lasers and computers to combustion science and technology. Shortly thereafter, the Combustion Research Facility (CRF) was established at Sandia's Livermore location. Designated a ''User Facility,'' the charter of the CRF was to develop and maintain special-purpose resources to support a nationwide initiative--involving US universities, industry, and national laboratories--to improve our understanding and control of combustion. This report includes descriptions of several research projects which have been stimulated by Working Groups and involve the on-site participation of industry scientists. DOE's Industry Technology Fellowship Program has been instrumental in the success of some of the joint efforts. The remainder of this report presents research results of calendar year 1987, separated thematically into nine categories. Refereed journal articles appearing in print during 1987, along with selected other publications, are included at the end of Section 10. In addition to our ''traditional'' research--chemistry, reacting flow, diagnostics, engine combustion, and coal combustion--you will note continued progress in somewhat recent themes: pulse combustion, high temperature materials, and energetic materials, for example. Moreover, we have just started a small, new effort to understand combustion-related issues in the management of toxic and hazardous materials.

  11. Neuropsychological impairment among former microelectronics workers.

    Science.gov (United States)

    Bowler, R M; Mergler, D; Huel, G; Harrison, R; Cone, J

    1991-01-01

    Although chemicals posing potential neurotoxic hazards are commonly used in the microelectronics industry, there has been no systematic study of possible chronic nervous system effects in microelectronics workers. The objective of the present study was to assess neuropsychological functions of a group of former microelectronics plant assembly workers and a group of referents, using a matched pair design. During employment, the former microelectronics workers had been exposed to multiple organic solvents, including trichloroethylene, xylene, chlorofluorocarbons and trichloroethane. Referents were recruited from the same geographic region. From a pool of 180 former workers and 157 referents, 67 pairs were matched on the basis of age, sex, ethnicity, educational level, sex and number of children. Comparison of results on the subtests of the California Neuropsychological Screening Battery-Revised (CNS-R) revealed significantly lower performance by the former microelectronics workers on tests of attention/concentration, verbal ability, memory functions, visuospatial functions, visuomotor speed, cognitive flexibility, psychomotor speed, and reaction time (t-test for pairs or Wilcoxon Signed Rank p less than 0.05). No significant differences were observed for performance on tests assessing mental status, visual recall, tactile function and learning. This overall pattern of impairment is consistent with organic solvent-related chronic toxic encephalopathy, and possible early stages of dementia. These findings underline the need for more studies among workers currently or previously employed in microelectronics industries.

  12. Sandia National Laboratories Institutional Plan FY1994--1999

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-01

    This report presents a five year plan for the laboratory. This plan takes advantage of the technical strengths of the lab and its staff to address issues of concern to the nation on a scope much broader than Sandia`s original mission, while maintaining the general integrity of the laboratory. The plan proposes initiatives in a number of technologies which overlap the needs of its customers and the strengths of its staff. They include: advanced manufacturing technology; electronics; information and computational technology; transportation energy technology and infrastructure; environmental technology; energy research and technology development; biomedical systems engineering; and post-cold war defense imperatives.

  13. PDC (polycrystalline diamond compact) bit research at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Finger, J.T.; Glowka, D.A.

    1989-06-01

    From the beginning of the geothermal development program, Sandia has performed and supported research into polycrystalline diamond compact (PDC) bits. These bits are attractive because they are intrinsically efficient in their cutting action (shearing, rather than crushing) and they have no moving parts (eliminating the problems of high-temperature lubricants, bearings, and seals.) This report is a summary description of the analytical and experimental work done by Sandia and our contractors. It describes analysis and laboratory tests of individual cutters and complete bits, as well as full-scale field tests of prototype and commercial bits. The report includes a bibliography of documents giving more detailed information on these topics. 26 refs.

  14. Integrated microelectronics for smart textiles.

    Science.gov (United States)

    Lauterbach, Christl; Glaser, Rupert; Savio, Domnic; Schnell, Markus; Weber, Werner

    2005-01-01

    The combination of textile fabrics with microelectronics will lead to completely new applications, thus achieving elements of ambient intelligence. The integration of sensor or actuator networks, using fabrics with conductive fibres as a textile motherboard enable the fabrication of large active areas. In this paper we describe an integration technology for the fabrication of a "smart textile" based on a wired peer-to-peer network of microcontrollers with integrated sensors or actuators. A self-organizing and fault-tolerant architecture is accomplished which detects the physical shape of the network. Routing paths are formed for data transmission, automatically circumventing defective or missing areas. The network architecture allows the smart textiles to be produced by reel-to-reel processes, cut into arbitrary shapes subsequently and implemented in systems at low installation costs. The possible applications are manifold, ranging from alarm systems to intelligent guidance systems, passenger recognition in car seats, air conditioning control in interior lining and smart wallpaper with software-defined light switches.

  15. Life cycle assessment applied to the sector of microelectronic devices

    Science.gov (United States)

    Matarazzo, Agata; Ingrao, Carlo; Clasadonte, Maria Teresa

    2016-07-01

    This work is about the application of LCA to the ends of the environmental assessment of pure-silicon wafers production. The input-data quantification is realized studying two microelectronic devices and presenting schematically tables and graphs, to be easily interpreted. This will allow help the reader to individuate, clearly and immediately, the materials flows and the relationships among the different steps of the production process. The material flows, in terms of raw materials use and energy consumption, were studied using the data provided by a firm involved in the microelectronic device production field. The two devices environmental analysis was developed considering potential effects such as Acidification, Eutrophication, Ozone reduction, Global warming, Ozone photochemical formation, Human Toxicity.

  16. PREFACE: The Second Conference on Microelectronics, Microsystems and Nanotechnology

    Science.gov (United States)

    Nassiopoulou, Androula G.; Papanikolaou, Nikos; Tsamis, Christos

    2005-01-01

    The Second Conference on Microelectronics, Microsystems and Nanotechnology took place at the National Centre for Scientific Research `Demokritos', in Athens, Greece, between 14 and 17 November 2004. The conference was organized by the Institute of Microelectronics (IMEL) with the aim to bring together scientists and engineers working in the above exciting fields in an interactive forum. The conference included 45 oral presentations with 9 invited papers and was attended by 146 participants from 16 countries. The topics covered were nanotechnologies, quantum devices, sensors, micro- and nano-systems, semiconductor devices, C-MOS fabrication and characterization techniques, new materials, and IC design. Quantum devices and nanostructured materials attracted considerable attention. Both theoretical and experimental studies of metallic and semiconducting quantum systems were presented, with emphasis on their applications in electronics, optoelectronics, and nanocrystal memory devices. Another exciting topic was the recent developments in biocompatible lithographic processes for applications in biosensors. In particular novel processes for bio-friendly lithography, together with innovations in Si sensors for applications in medicine and food industry were presented. Recent developments and perspectives in CMOS technology towards the ultimate limit were also discussed. The conference covered issues and concepts of IC design with two invited talks on RF design and cryptography.The conference included presentations from several companies active in the field of microelectronics and systems in Greece.

  17. Space robotics programs at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Klarer, P.

    1993-01-01

    Existing robotic rover and space satellite technologies at Sandia National Laboratories (SNL), coupled with existing launch vehicles and converted military Multiple Independent Reentry Vehicle (MIRV) technologies, can be applied towards the realization of a robotic lunar rover mission in the near term. SNL`s Advanced Vehicle Development Department has been designing, producing, and operating prototype rover systems at the Robotic Vehicle Range facility since 1984, and has extensive experience with teleoperated and semiautonomous mobile robotic systems. SNL`s Space Systems Directorate has been designing, producing, and operating satellite systems and subsystems in earth orbit for national security missions since the early 1960`s. The facilities and robotic vehicle fleet at SNL`s Robotic Vehicle Range (SNL-RVR) have been used to support technology base development in applications ranging from DoD battlefield and security missions, to multi-agency nuclear emergency response team exercises and the development of a prototype robotic rover for planetary exploration. Recent activities at the SNL-RVR include the Robotic All Terrain Lunar Exploration Rover (RATLER) prototype development program, exploratory studies on a Near Term Lunar Return Mission scenario for small robotic rovers based on existing space hardware technology, and demonstrations of the utility of existing rover technologies for performing remote field geology tasks similar to those envisioned on a robotic lunar rover mission. Specific technologies demonstrated include low data rate teleoperation, multi-vehicle control, remote site and sample inspection, and standard bandwidth stereo vision. The paper describes Sandia National Laboratories` activities in the Space Robotics area, and highlights the laboratory`s supporting technical capabilities.

  18. Sandia software guidelines: Software quality planning

    Energy Technology Data Exchange (ETDEWEB)

    1987-08-01

    This volume is one in a series of Sandia Software Guidelines intended for use in producing quality software within Sandia National Laboratories. In consonance with the IEEE Standard for Software Quality Assurance Plans, this volume identifies procedures to follow in producing a Software Quality Assurance Plan for an organization or a project, and provides an example project SQA plan. 2 figs., 4 tabs.

  19. Using federal technology policy to strength the US microelectronics industry

    Science.gov (United States)

    Gover, J. E.; Gwyn, C. W.

    1994-07-01

    A review of US and Japanese experiences with using microelectronics consortia as a tool for strengthening their respective industries reveals major differences. Japan has established catch-up consortia with focused goals. These consortia have a finite life targeted from the beginning, and emphasis is on work that supports or leads to product and process-improvement-driven commercialization. Japan's government has played a key role in facilitating the development of consortia and has used consortia promote domestic competition. US consortia, on the other hand, have often emphasized long-range research with considerably less focus than those in Japan. The US consortia have searched for and often made revolutionary technology advancements. However, technology transfer to their members has been difficult. Only SEMATECH has assisted its members with continuous improvements, compressing product cycles, establishing relationships, and strengthening core competencies. The US government has not been a catalyst nor provided leadership in consortia creation and operation. We propose that in order to regain world leadership in areas where US companies lag foreign competition, the US should create industry-wide, horizontal-vertical, catch-up consortia or continue existing consortia in the six areas where the US lags behind Japan -- optoelectronics, displays, memories, materials, packaging, and manufacturing equipment. In addition, we recommend that consortia be established for special government microelectronics and microelectronics research integration and application. We advocate that these consortia be managed by an industry-led Microelectronics Alliance, whose establishment would be coordinated by the Department of Commerce. We further recommend that the Semiconductor Research Corporation, the National Science Foundation Engineering Research Centers, and relevant elements of other federal programs be integrated into this consortia complex.

  20. Using federal technology policy to strength the US microelectronics industry

    Energy Technology Data Exchange (ETDEWEB)

    Gover, J.E.; Gwyn, C.W.

    1994-07-01

    A review of US and Japanese experiences with using microelectronics consortia as a tool for strengthening their respective industries reveals major differences. Japan has established catch-up consortia with focused goals. These consortia have a finite life targeted from the beginning, and emphasis is on work that supports or leads to product and process-improvement-driven commercialization. Japan`s government has played a key role in facilitating the development of consortia and has used consortia promote domestic competition. US consortia, on the other hand, have often emphasized long-range research with considerably less focus than those in Japan. The US consortia have searched for and often made revolutionary technology advancements. However, technology transfer to their members has been difficult. Only SEMATECH has assisted its members with continuous improvements, compressing product cycles, establishing relationships, and strengthening core competencies. The US government has not been a catalyst nor provided leadership in consortia creation and operation. We propose that in order to regain world leadership in areas where US companies lag foreign competition, the US should create industry-wide, horizontal-vertical, catch-up consortia or continue existing consortia in the six areas where the US lags behind Japan -- optoelectronics, displays, memories, materials, packaging, and manufacturing equipment. In addition, we recommend that consortia be established for special government microelectronics and microelectronics research integration and application. We advocate that these consortia be managed by an industry-led Microelectronics Alliance, whose establishment would be coordinated by the Department of Commerce. We further recommend that the Semiconductor Research Corporation, the National Science Foundation Engineering Research Centers, and relevant elements of other federal programs be integrated into this consortia complex.

  1. Sandia National Laboratories analysis code data base

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, C.W.

    1994-11-01

    Sandia National Laboratories, mission is to solve important problems in the areas of national defense, energy security, environmental integrity, and industrial technology. The Laboratories` strategy for accomplishing this mission is to conduct research to provide an understanding of the important physical phenomena underlying any problem, and then to construct validated computational models of the phenomena which can be used as tools to solve the problem. In the course of implementing this strategy, Sandia`s technical staff has produced a wide variety of numerical problem-solving tools which they use regularly in the design, analysis, performance prediction, and optimization of Sandia components, systems and manufacturing processes. This report provides the relevant technical and accessibility data on the numerical codes used at Sandia, including information on the technical competency or capability area that each code addresses, code ``ownership`` and release status, and references describing the physical models and numerical implementation.

  2. Applications of laser direct-write for embedding microelectronics

    Science.gov (United States)

    Piqué, Alberto; Charipar, Nicholas A.; Kim, Heungsoo; Auyeung, Ray C. Y.; Mathews, Scott A.

    2007-03-01

    The use of direct-write techniques might revolutionize the way microelectronic devices such as interconnects, passives, IC's, antennas, sensors and power sources are designed and fabricated. The Naval Research Laboratory has developed a laser-based microfabrication process for direct-writing the materials and components required for the assembly and interconnection of the above devices. This laser direct-write (LDW) technique is capable of operating in subtractive, additive, and transfer mode. In subtractive mode, the system operates as a laser micromachining workstation capable of achieving precise depth and surface roughness control. In additive mode, the system utilizes a laser-forward transfer process for the deposition of metals, oxides, polymers and composites under ambient conditions onto virtually any type of surface, thus functioning as a laser printer for patterns of electronic materials. Furthermore, in transfer mode, the system is capable of transferring individual devices, such as semiconductor bare die or surface mount devices, inside a trench or recess in a substrate, thus performing the same function of the pick-and-place machines used in circuit board manufacture. The use of this technique is ideally suited for the rapid prototyping of embedded microelectronic components and systems while allowing the overall circuit design and layout to be easily modified or adapted to any specific application or form factor. This paper describes the laser direct-write process as applied to the forward transfer of microelectronic devices.

  3. Sandia Data Archive (SDA) file specifications

    Energy Technology Data Exchange (ETDEWEB)

    Dolan, Daniel H. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ao, Tommy [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-02-01

    The Sandia Data Archive (SDA) format is a specific implementation of the HDF5 (Hierarchal Data Format version 5) standard. The format was developed for storing data in a universally accessible manner. SDA files may contain one or more data records, each associated with a distinct text label. Primitive records provide basic data storage, while compound records support more elaborate grouping. External records allow text/binary files to be carried inside an archive and later recovered. This report documents version 1.0 of the SDA standard. The information provided here is sufficient for reading from and writing to an archive. Although the format was original designed for use in MATLAB, broader use is encouraged.

  4. Carbon-ionogel supercapacitors for integrated microelectronics.

    Science.gov (United States)

    Leung, Greg; Smith, Leland; Lau, Jonathan; Dunn, Bruce; Chui, Chi On

    2016-01-22

    To exceed the performance limits of dielectric capacitors in microelectronic circuit applications, we design and demonstrate on-chip coplanar electric double-layer capacitors (EDLCs), or supercapacitors, employing carbon-coated gold electrodes with ionogel electrolyte. The formation of carbon-coated microelectrodes is accomplished by solution processing and results in a ten-fold increase in EDLC capacitance compared to bare gold electrodes without carbon. At frequencies up to 10 Hz, an areal capacitance of 2.1 pF μm(-2) is achieved for coplanar carbon-ionogel EDLCs with 10 μm electrode gaps and 0.14 mm(2) electrode area. Our smallest devices, comprised of 5 μm electrode gaps and 80 μm(2) of active electrode area, reach areal capacitance values of ∼0.3 pF μm(-2) at frequencies up to 1 kHz, even without carbon. To our knowledge, these are the highest reported values to date for on-chip EDLCs with sub-mm(2) areas. A physical EDLC model is developed through the use of computer-aided simulations for design exploration and optimization of coplanar EDLCs. Through modeling and comparison with experimental data, we highlight the importance of reducing the electrode gap and electrolyte resistance to achieve maximum performance from on-chip EDLCs.

  5. Health hazards in the microelectronics industry.

    Science.gov (United States)

    Geiser, K

    1986-01-01

    The microelectronics industry is explored as a source of occupational health hazards resulting from the extensive use of toxic chemicals in the production of semiconductor chips and the assembly of electronic components. Information is provided on the range of chemicals used in the industry and their particular health implications. Case materials are drawn from Massachusetts' "Route 128" region and California's "Silicon Valley." Problems with worker exposure in the plants are compared with the risks experienced by residents of local neighborhoods from the leakage of industrial chemicals from underground storage tanks into the local groundwater used for drinking water. The recent development of the industry, its highly innovative character, the absence of unions and organizations for worker protection, and the persistence of a public perception that the industry is relatively safe and clean, are all identified as determinants of the extent of health hazards posed by chemical exposure. The paper concludes with recommendations for further studies, worker organization, and increased attention to the reduction of the volume and toxicity of chemicals in industrial production.

  6. IP validation in remote microelectronics testing

    Science.gov (United States)

    Osseiran, Adam; Eshraghian, Kamran; Lachowicz, Stefan; Zhao, Xiaoli; Jeffery, Roger; Robins, Michael

    2004-03-01

    This paper presents the test and validation of FPGA based IP using the concept of remote testing. It demonstrates how a virtual tester environment based on a powerful, networked Integrated Circuit testing facility, aimed to complement the emerging Australian microelectronics based research and development, can be employed to perform the tasks beyond the standard IC test. IC testing in production consists in verifying the tested products and eliminating defective parts. Defects could have a number of different causes, including process defects, process migration and IP design and implementation errors. One of the challenges in semiconductor testing is that while current fault models are used to represent likely faults (stuck-at, delay, etc.) in a global context, they do not account for all possible defects. Research in this field keeps growing but the high cost of ATE is preventing a large community from accessing test and verification equipment to validate innovative IP designs. For these reasons a world class networked IC teletest facility has been established in Australia under the support of the Commonwealth government. The facility is based on a state-of-the-art semiconductor tester operating as a virtual centre spanning Australia and accessible internationally. Through a novel approach the teletest network provides virtual access to the tester on which the DUT has previously been placed. The tester software is then accessible as if the designer is sitting next to the tester. This paper presents the approach used to test and validate FPGA based IPs using this remote test approach.

  7. Chemical Mechanical Planarization (CMP) for Microelectronic Applications

    Institute of Scientific and Technical Information of China (English)

    Li Yuzhuo

    2004-01-01

    Surface planarity is of paramount importance in microelectronics. Chemical Mechanical Polishing (CMP) is the most viable approach to address the planarity issues during the fabrication of advanced semiconductor devices. With the integration of copper as interconnect and low k materials as dielectric, the CMP community is facing an ever increasing demand on reducing defectivity without scarifying production throughput. Key issues in CMP today include reduction of surface defectivity and enhancement of planarization efficiency. More specifically, the polished surface should be free of defects such as scratches, pits, corrosion spots, and residue particles. To accomplish these goals, we have investigated a wide range of pathways including reduction of oversized particles,use of unique abrasives such as functionalized nanoparticles, and development of polishing solution without abrasive particles.In this presentation, some fundamental aspects of the CMP process will be given first.Several academic and industrial examples will be used to illustrate the issues and challenges during the implementation of various slurry designs into the CMP processes.

  8. Analogy among microfluidics, micromechanics, and microelectronics.

    Science.gov (United States)

    Li, Sheng-Shian; Cheng, Chao-Min

    2013-10-07

    We wish to illuminate the analogous link between microfluidic-based devices, and the already established pairing of micromechanics and microelectronics to create a triangular/three-way scientific relationship as a means of interlinking familial disciplines and accomplishing two primary goals: (1) to facilitate the modeling of multidisciplinary domains; and, (2) to enable us to co-simulate the entire system within a compact circuit simulator (e.g., Cadence or SPICE). A microfluidic channel-like structure embedded in a micro-electro-mechanical resonator via our proposed CMOS-MEMS technology is used to illustrate the connections among microfluidics, micromechanics, and microelectronics.

  9. High reliability plastic packaging for microelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Sweet, J.N.; Peterson, D.W.; Hsia, A.H.; Tuck, M.

    1997-07-01

    Goal was Assembly Test Chips (ATCs) which could be used for evaluating plastic encapsulation technologies. Circuits were demonstrated for measuring Au-Al wirebond and Al metal corrosion failure rates during accelerated temperature and humidity testing. The test circuits on the ATC02.5 chip were very sensitive to extrinsic or processing induced failure rates. Accelerated aging experiments were conducted with unpassivated triple track Al structures on the ATC02.6 chip; the unpassivated tracks were found to be very sensitive to particulate contamination. Some modifications to existing circuitry were suggested. The piezoresistive stress sensing circuitry designed for the ATC04 test chip was found suitable for determining the change in the state of mechanical stress at the die when both initial and final measurements were made near room temperature (RT). Attempt to measure thermal stress between RT and a typical polymer glass transition temperature failed because of excessive die resistor- substrate leakage currents at the high temperature end; suitable circuitry changes were developed to overcome this problem. One temperature and humidity experiment was conducted with Sandia developed static radom access memory parts to examine non-corrosion CMOS failures; this objective was not achieved, but corrosion failure at the metal to Si contacts on the die surface could be detected. This 2-year effort resulted in new designs for test circuits which could be used on an advanced ATC for reliability assessment in Defense Programs electronics development projects.

  10. Building business from technology: The Sandia experience

    Energy Technology Data Exchange (ETDEWEB)

    Traylor, L.B.

    1995-07-01

    This paper describes New Ventures, a new initiative at Sandia National Laboratories that encourages the creation of new businesses based on laboratory technology as a timely, efficient means of technology transfer. Sandia`s New Ventures program has shown that a dedicated effort can produce significant results. In the three years prior to this program`s launch, just two ventures per year on average were created based on laboratory technology. By comparison, the New Ventures program has enabled 20 new ventures in its first nine months of full operation.

  11. Building business from technology: The Sandia experience

    Energy Technology Data Exchange (ETDEWEB)

    Traylor, L.B.

    1995-07-01

    This paper describes New Ventures, a new initiative at Sandia National Laboratories that encourages the creation of new businesses based on laboratory technology as a timely, efficient means of technology transfer. Sandia`s New Ventures program has shown that a dedicated effort can produce significant results. In the three years prior to this program`s launch, just two ventures per year on average were created based on laboratory technology. By comparison, the New Ventures program has enabled 20 new ventures in its first nine months of full operation.

  12. Trusted Defense Microelectronics: Future Access and Capabilities Are Uncertain

    Science.gov (United States)

    2015-10-28

    TRUSTED DEFENSE MICROELECTRONICS Future Access and Capabilities Are Uncertain Statement of Marie A. Mak...1. REPORT DATE OCT 2015 2. REPORT TYPE 3. DATES COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE Trusted Defense Microelectronics ...House of Representatives October 2015 TRUSTED DEFENSE MICROELECTRONICS Future Access and Capabilities Are Uncertain Why GAO Did This Study DOD’s

  13. Guidelines for Sandia ASCI Verification and Validation Plans - Content and Format: Version 1.0

    Energy Technology Data Exchange (ETDEWEB)

    TRUCANO,TIMOTHY G.; MOYA,JAIME L.

    1999-12-01

    This report summarizes general guidelines for the development of Verification and Validation (V and V) plans for ASCI code projects at Sandia National Laboratories. The main content categories recommended by these guidelines for explicit treatment in Sandia V and V plans are (1) stockpile drivers influencing the code development project (2) the key phenomena to be modeled by the individual code; (3) software verification strategy and test plan; and (4) code validation strategy and test plans. The authors of this document anticipate that the needed content of the V and V plans for the Sandia ASCI codes will evolve as time passes. These needs will be reflected by future versions of this document.

  14. Visual dysfunction among former microelectronics assembly workers.

    Science.gov (United States)

    Mergler, D; Huel, G; Bowler, R; Frenette, B; Cone, J

    1991-01-01

    Although known neurotoxins with potential ophthalmotoxic properties are commonly used in microelectronics assembly, there has been no systematic study of visual disturbances among past or present workers in this industry. The objective of the present study was to compare visual functions, using a matched-pair design, between former workers from a microelectronics plant and a local reference population. From an initial population of 180 former workers and 157 potential referents, 54 pairs were matched for age (+/- 3 y), education (+/- 2 y), sex, ethnic origin, and number of children. Near and far visual acuity, chromatic discrimination, and near contrast sensitivity were assessed monocularly. Paired comparisons (Signed-rank Wilcoxon test) revealed that the former microelectronics workers had significantly lower contrast sensitivity, particularly in the intermediate frequencies, independently of near visual acuity loss. There were no differences for far visual acuity in both eyes. Even though near visual acuity and color vision were compromised among the former workers, the differences were only significant for one eye, as was the prevalence of acquired dyschromatopsia (chi-square for matched pairs, p less than .001). These findings suggest a pattern of contrast sensitivity deficits consistent with impairment to foveal and/or neuro-optic pathways among these former microelectronics workers. Exposure to ophthalmotoxic chemicals is proposed as the most probable risk factor.

  15. Carbon nanotubes as heat dissipaters in microelectronics

    DEFF Research Database (Denmark)

    Pérez Paz, Alejandro; García-Lastra, Juan María; Markussen, Troels

    2013-01-01

    We review our recent modelling work of carbon nanotubes as potential candidates for heat dissipation in microelectronics cooling. In the first part, we analyze the impact of nanotube defects on their thermal transport properties. In the second part, we investigate the loss of thermal properties...

  16. International Conference on Microelectronics, Electromagnetics and Telecommunications

    CERN Document Server

    Rao, N; Kumar, S; Raj, C; Rao, V; Sarma, G

    2016-01-01

    This volume contains 73 papers presented at ICMEET 2015: International Conference on Microelectronics, Electromagnetics and Telecommunications. The conference was held during 18 – 19 December, 2015 at Department of Electronics and Communication Engineering, GITAM Institute of Technology, GITAM University, Visakhapatnam, INDIA. This volume contains papers mainly focused on Antennas, Electromagnetics, Telecommunication Engineering and Low Power VLSI Design.

  17. Failure and Delamination in Microelectronic Packages

    NARCIS (Netherlands)

    Sadeghinia, M.

    2013-01-01

    Thin layers of dissimilar materials are used in most microelectronic components in order to achieve special functional requirements. Generally, the interface between two adjacent materials forms a weak link, not only because of the relatively low delamination strength, but also because of the existi

  18. Airbags to Martian Landers: Analyses at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Gwinn, K.W.

    1994-03-01

    A new direction for the national laboratories is to assist US business with research and development, primarily through cooperative research and development agreements (CRADAs). Technology transfer to the private sector has been very successful as over 200 CRADAs are in place at Sandia. Because of these cooperative efforts, technology has evolved into some new areas not commonly associated with the former mission of the national laboratories. An example of this is the analysis of fabric structures. Explicit analyses and expertise in constructing parachutes led to the development of a next generation automobile airbag; which led to the construction, testing, and analysis of the Jet Propulsion Laboratory Mars Environmental Survey Lander; and finally led to the development of CAD based custom garment designs using 3D scanned images of the human body. The structural analysis of these fabric structures is described as well as a more traditional example Sandia with the test/analysis correlation of the impact of a weapon container.

  19. NNSA Master Asset Map - Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Billie, Gepetta S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-01-01

    This report gives information on the following topics related to Sandia National Laboratories: site leadership's vision, condition, footprint management, major gaps and risks, and proposed investment plan.

  20. Plan for advanced microelectronics processing technology application

    Energy Technology Data Exchange (ETDEWEB)

    Goland, A.N.

    1990-10-01

    The ultimate objective of the tasks described in the research agreement was to identify resources primarily, but not exclusively, within New York State that are available for the development of a Center for Advanced Microelectronics Processing (CAMP). Identification of those resources would enable Brookhaven National Laboratory to prepare a program plan for the CAMP. In order to achieve the stated goal, the principal investigators undertook to meet the key personnel in relevant NYS industrial and academic organizations to discuss the potential for economic development that could accompany such a Center and to gauge the extent of participation that could be expected from each interested party. Integrated of these discussions was to be achieved through a workshop convened in the summer of 1990. The culmination of this workshop was to be a report (the final report) outlining a plan for implementing a Center in the state. As events unfolded, it became possible to identify the elements of a major center for x-ray lithography on Lone Island at Brookhaven National Laboratory. The principal investigators were than advised to substitute a working document based upon that concept in place of a report based upon the more general CAMP workshop originally envisioned. Following that suggestion from the New York State Science and Technology Foundation, the principals established a working group consisting of representatives of the Grumman Corporation, Columbia University, the State University of New York at Stony Brook, and Brookhaven National Laboratory. Regular meetings and additional communications between these collaborators have produced a preproposal that constitutes the main body of the final report required by the contract. Other components of this final report include the interim report and a brief description of the activities which followed the establishment of the X-ray Lithography Center working group.

  1. Sandia`s network for SC `97: Supporting visualization, distributed cluster computing, and production data networking with a wide area high performance parallel asynchronous transfer mode (ATM) network

    Energy Technology Data Exchange (ETDEWEB)

    Pratt, T.J.; Martinez, L.G.; Vahle, M.O.; Archuleta, T.V.; Williams, V.K.

    1998-05-01

    The advanced networking department at Sandia National Laboratories has used the annual Supercomputing conference sponsored by the IEEE and ACM for the past several years as a forum to demonstrate and focus communication and networking developments. At SC `97, Sandia National Laboratories (SNL), Los Alamos National Laboratory (LANL), and Lawrence Livermore National Laboratory (LLNL) combined their SC `97 activities within a single research booth under the Advance Strategic Computing Initiative (ASCI) banner. For the second year in a row, Sandia provided the network design and coordinated the networking activities within the booth. At SC `97, Sandia elected to demonstrate the capability of the Computation Plant, the visualization of scientific data, scalable ATM encryption, and ATM video and telephony capabilities. At SC `97, LLNL demonstrated an application, called RIPTIDE, that also required significant networking resources. The RIPTIDE application had computational visualization and steering capabilities. This paper documents those accomplishments, discusses the details of their implementation, and describes how these demonstrations support Sandia`s overall strategies in ATM networking.

  2. DESALINATION AND WATER TREATMENT RESEARCH AT SANDIA NATIONAL LABORATORIES.

    Energy Technology Data Exchange (ETDEWEB)

    Rigali, Mark J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Miller, James E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Altman, Susan J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Biedermann, Laura [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Brady, Patrick Vane. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kuzio, Stephanie P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Nenoff, Tina M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rempe, Susan [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-11-01

    Water is the backbone of our economy - safe and adequate supplies of water are vital for agriculture, industry, recreation, and human consumption. While our supply of water today is largely safe and adequate, we as a nation face increasing water supply challenges in the form of extended droughts, demand growth due to population increase, more stringent health-based regulation, and competing demands from a variety of users. To meet these challenges in the coming decades, water treatment technologies, including desalination, will contribute substantially to ensuring a safe, sustainable, affordable, and adequate water supply for the United States. This overview documents Sandia National Laboratories' (SNL, or Sandia) Water Treatment Program which focused on the development and demonstration of advanced water purification technologies as part of the larger Sandia Water Initiative. Projects under the Water Treatment Program include: (1) the development of desalination research roadmaps (2) our efforts to accelerate the commercialization of new desalination and water treatment technologies (known as the 'Jump-Start Program),' (3) long range (high risk, early stage) desalination research (known as the 'Long Range Research Program'), (4) treatment research projects under the Joint Water Reuse & Desalination Task Force, (5) the Arsenic Water Technology Partnership Program, (6) water treatment projects funded under the New Mexico Small Business Administration, (7) water treatment projects for the National Energy Technology Laboratory (NETL) and the National Renewable Energy Laboratory (NREL), (8) Sandia- developed contaminant-selective treatment technologies, and finally (9) current Laboratory Directed Research and Development (LDRD) funded desalination projects.

  3. Sandia National Laboratories, California proposed CREATE facility environmental baseline survey.

    Energy Technology Data Exchange (ETDEWEB)

    Catechis, Christopher Spyros

    2013-10-01

    Sandia National Laboratories, Environmental Programs completed an environmental baseline survey (EBS) of 12.6 acres located at Sandia National Laboratories/California (SNL/CA) in support of the proposed Collaboration in Research and Engineering for Advanced Technology and Education (CREATE) Facility. The survey area is comprised of several parcels of land within SNL/CA, County of Alameda, California. The survey area is located within T 3S, R 2E, Section 13. The purpose of this EBS is to document the nature, magnitude, and extent of any environmental contamination of the property; identify potential environmental contamination liabilities associated with the property; develop sufficient information to assess the health and safety risks; and ensure adequate protection for human health and the environment related to a specific property.

  4. Toward atom probe tomography of microelectronic devices

    Science.gov (United States)

    Larson, D. J.; Lawrence, D.; Lefebvre, W.; Olson, D.; Prosa, T. J.; Reinhard, D. A.; Ulfig, R. M.; Clifton, P. H.; Bunton, J. H.; Lenz, D.; Olson, J. D.; Renaud, L.; Martin, I.; Kelly, T. F.

    2011-11-01

    Atom probe tomography and scanning transmission electron microscopy has been used to analyze a commercial microelectronics device prepared by depackaging and focused ion beam milling. Chemical and morphological data are presented from the source, drain and channel regions, and part of the gate oxide region of an Intel® i5-650 p-FET device demonstrating feasibility in using these techniques to investigate commercial chips.

  5. Environmental health aspects of the microelectronics industry.

    Science.gov (United States)

    Himmelstein, J S; Levy, B S

    1986-01-01

    This article reviews examples of contamination to the surface or groundwater, the ambient air, and soil resulting from the microelectronics industry. The potential effects on human health arising from such environmental contamination are discussed, as well as aspects of their diagnosis, treatment, and related public health implications. Given the high costs of pollution control, the emphasis must be on prevention, which can be facilitated by a high level of suspicion and by the design of safety and pollution control into manufacturing processes.

  6. Moore's law: the future of Si microelectronics

    Directory of Open Access Journals (Sweden)

    Scott E. Thompson

    2006-06-01

    Full Text Available Soon after Bardeen, Brattain, and Shockley invented a solid-state device in 19471 to replace electron vacuum tubes, the microelectronics industry and a revolution started. Since its birth, the industry has experienced four decades of unprecedented explosive growth driven by two factors: Noyce and Kilby inventing the planar integrated circuit2,3 and the advantageous characteristics that result from scaling (shrinking solid-state devices.

  7. [Physiological and hygienic characteristic of high-precision manufacturing operations in microelectronics].

    Science.gov (United States)

    Kirillov, V F; Mironov, A I; Gadakchan, K A; Mekhova, M M; Spiridonova, V S

    2010-01-01

    It was shown that workers performing high-precision manufacturing operations in microelectronic industry undergo severe visual, nervous and emotional stress combined with significant locomotor load, air deionization and deozonation, bacterial contamination, and UV deficit at their workplaces. These working conditions promote development of negative changes in the visual analyzer, nervous and emotional disorders, disturbances of systemic and regional hemodynamics. Also impaired is the functional state of the upper limb neuromuscular apparatus, central nervous and cardiovascular systems. The proposed certified complex of organizational, sanitary, hygienic, physiological, ergonomic, therapeutic and preventive measures has positive influence on the working capacity of employees in microelectronic industry.

  8. Analysis of the impact of the regulation of toxic substances on Sandia

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, C. Jr.; Pigg, J.

    1980-10-01

    In recent years, Congress has passed two regulatory acts, namely the Occupational Safety and Health Act (OSHA) and the Toxic Substance Control Act (TSCA) which seek to control the manufacture, use, and disposal of hazardous chemical substances. These acts can have a significant impact on Sandia's missions and will particularly affect those organizations involved in materials development and selection. The primary purpose of this report is to describe in some detail the impact of these acts on Sandia's corporate goals and make recommendations on what our response should be. Also described in this report is the present position of Sandia with respect to these regulatory acts and the policies and actions that Sandia has taken to date in an effort to minimize their impact.

  9. Leveraging Microelectronics Research to Enable A Smarter Planet

    Science.gov (United States)

    Dalton, Timothy J.

    2009-10-01

    Over the course of the last fifty years, the microelectronics industry has made tremendous strides in the development and manufacturing of ever more complex integrated circuits (IC). These circuits have typically been applied to the information technology (IT) industry and have driven improvements in the computational power per dollar of many orders of magnitude. Part of the ``toolbox'' of skills acquired to produce integrated circuits is the ability to form desired patterns at ever decreasing sizes. The minimum controllable feature size has been reduced by six orders of magnitude (from millimeters to nanometers) during the last fifty years. With feature sizes rapidly approaching 10nm, the conventional silicon IC industry is nearing a threshold with the end of conventional silicon scaling approaching. Research today focuses on new device structure to replace the CMOS FET as the engine of the IT industry. A very exciting research area today is the concept of taking the skill-set acquired from IC research, development, and manufacturing, and applying those skills into new domains where they can enable a ``smarter planet''. These new domains include areas such as energy, water, and health care / life sciences. All of these are outside of the traditional IT focus for microelectronics research, yet, the new ``smarter planet'' domains may form the basis for future industries. This presentation will look at the evolution of IBM's research model and focus, shifting from one solely focused on IT, to one that compliments IT research with Smarter Planet domains.

  10. Summary of Sandia research on metal tritides : FY 2007.

    Energy Technology Data Exchange (ETDEWEB)

    Browning, James Frederick (Oak Ridge National Laboratory, Oak Ridge, TN); Kammler, Daniel R.; Snow, Clark Sheldon; Ferrizz, Robert Matthew; Rodriguez, Mark Andrew; Wixom, Ryan R.; Espada, Loren I.

    2008-05-01

    Sandia National Laboratories has cradle to grave responsibility for all neutron generators in the US nuclear weapons stockpile. As such, much research effort is exerted to develop a comprehensive understanding of all the major components of a neutron generator. One of the key components is the tritium containing target. The target is a thin metal tritide film. Sandia's research into metal tritides began in the early 1960's with a collaboration with the Denver Research Institute (DRI) and continues to this day with a major in house research effort. This document is an attempt to briefly summarize what is known about the aging of erbium tritide and to review the major publications conducted at Sandia in FY 07. First, a review of our knowledge of helium in erbium tritide will be presented. Second, executive summaries of the six major SAND reports regarding neutron tube targets published in FY07 by Department 2735, the Applied Science and Technology Maturation Department, and research partners are presented.

  11. Sandia Software Guidelines, Volume 2. Documentation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    This volume is one in a series of Sandia Software Guidelines intended for use in producing quality software within Sandia National Laboratories. In consonance with the IEEE Standards for software documentation, this volume provides guidance in the selection of an adequate document set for a software project and example formats for many types of software documentation. A tutorial on life cycle documentation is also provided. Extended document thematic outlines and working examples of software documents are available on electronic media as an extension of this volume.

  12. Interfacial adhesion for microelectronics and MEMS devices

    Science.gov (United States)

    Kennedy, Marian Siobhan

    2007-12-01

    The reliability of thin film systems is important to the continued development of microelectronic and micro-electro-mechanical systems. Most often, reliability of these systems is tied to the ability of the films to remain adhered to its substrate. By measuring the amount of energy to separate the film, interfacial fracture energy, and prediciting trends researchers can predicts film lifetimes. Recent work to measure this energy has resulted in several different testing techniques including spontaneous buckling, indentation induced delamination and four point bending. Literature has shown good agreement between delamination test methods, but only when energy dissipation into the substrate is minimized. Using a W/Si system, the effect of energy dissipation was shown to decrease from 0.6 J/m2 to 0.2 J/m2 between different methods; one where the only fracture was along the interface and the other where cracking also occurred in the film and substrate. For systems where fracture only occurs along the interface, such as Au/Si, the calculated fracture energies are identical if the energy put into the system is kept near the needed strain energy to cause delamination. Overlayers of different stresses and thickness on Au/Si showed that the adhesion energies could change by a factor of three (Chapter 3). This dependence on applied energy is also shown when comparisons of four point bending and stressed overlayer test methods were completed on Pt/Si systems. The fracture energies of Pt/Ti/SiO2 were studied using four-point bending and compressive overlayers. Varying the thickness of the Ti film from 2 to 17 nm in a Pt/Ti/SiO2 system, both test methods showed an increase of adhesion energy until the nominal Ti thickness was 12nm. Then this adhesion energy began to decrease. This decrease was due to an increase in the Pt grain size after a nominal 12nm thickness (Chapter 4 and 5). While the trends in energy release rate are similar, the magnitude of the toughness between the

  13. Advanced Microelectronics Technologies for Future Small Satellite Systems

    Science.gov (United States)

    Alkalai, Leon

    1999-01-01

    Future small satellite systems for both Earth observation as well as deep-space exploration are greatly enabled by the technological advances in deep sub-micron microelectronics technologies. Whereas these technological advances are being fueled by the commercial (non-space) industries, more recently there has been an exciting new synergism evolving between the two otherwise disjointed markets. In other words, both the commercial and space industries are enabled by advances in low-power, highly integrated, miniaturized (low-volume), lightweight, and reliable real-time embedded systems. Recent announcements by commercial semiconductor manufacturers to introduce Silicon On Insulator (SOI) technology into their commercial product lines is driven by the need for high-performance low-power integrated devices. Moreover, SOI has been the technology of choice for many space semiconductor manufacturers where radiation requirements are critical. This technology has inherent radiation latch-up immunity built into the process, which makes it very attractive to space applications. In this paper, we describe the advanced microelectronics and avionics technologies under development by NASA's Deep Space Systems Technology Program (also known as X2000). These technologies are of significant benefit to both the commercial satellite as well as the deep-space and Earth orbiting science missions. Such a synergistic technology roadmap may truly enable quick turn-around, low-cost, and highly capable small satellite systems for both Earth observation as well as deep-space missions.

  14. Assessment of microelectronics packaging for high temperature, high reliability applications

    Energy Technology Data Exchange (ETDEWEB)

    Uribe, F.

    1997-04-01

    This report details characterization and development activities in electronic packaging for high temperature applications. This project was conducted through a Department of Energy sponsored Cooperative Research and Development Agreement between Sandia National Laboratories and General Motors. Even though the target application of this collaborative effort is an automotive electronic throttle control system which would be located in the engine compartment, results of this work are directly applicable to Sandia`s national security mission. The component count associated with the throttle control dictates the use of high density packaging not offered by conventional surface mount. An enabling packaging technology was selected and thermal models defined which characterized the thermal and mechanical response of the throttle control module. These models were used to optimize thick film multichip module design, characterize the thermal signatures of the electronic components inside the module, and to determine the temperature field and resulting thermal stresses under conditions that may be encountered during the operational life of the throttle control module. Because the need to use unpackaged devices limits the level of testing that can be performed either at the wafer level or as individual dice, an approach to assure a high level of reliability of the unpackaged components was formulated. Component assembly and interconnect technologies were also evaluated and characterized for high temperature applications. Electrical, mechanical and chemical characterizations of enabling die and component attach technologies were performed. Additionally, studies were conducted to assess the performance and reliability of gold and aluminum wire bonding to thick film conductor inks. Kinetic models were developed and validated to estimate wire bond reliability.

  15. Radiation hardness improvement of analog front-end microelectronic devices for particle accelerator

    Science.gov (United States)

    Miroshnichenko, A. G.; Rodin, A. S.; Bakerenkov, A. S.; Felitsyn, V. A.

    2016-10-01

    Series of schematic techniques for increasing radiation hardness of the current mirrors is developed. These techniques can be used for the design of analog front-end microelectronic devices based on the operational amplifiers. The circuit simulation of radiation degradation of current transmission coefficients was performed for various circuit solutions in LTSpice software.

  16. Optical packaging activities at Institute of Microelectronics (IME), Singapore

    Science.gov (United States)

    Teo, Keng-Hwa; Sudharsanam, Krishnamachari; Pamidighantam, Ramana V.; Yeo, Yongkee; Iyer, Mahadevan K.

    2002-08-01

    The development of optoelectronic components for gigabit Ethernet communications is converging towards access networks where the cost of device makes a significant impact on the market acceptance. Device fabrication and packaging cost have to be brought down with novel assembly and packaging methods. Singapore has established a reputation in semiconductor device development and fabrication with excellent process and packaging facilities. Institute of Microelectronics (IME) was founded in 1991 to add value to the Singapore electronics industry. IME is involved in the development of active and passive photonics components using Silicon and polymer materials. We present a brief report on the development activities taking place in the field of optical component packaging at IME in recent years. We present a review of our competence and some of the optical device packaging activities that are being undertaken.

  17. SAPLE: Sandia Advanced Personnel Locator Engine.

    Energy Technology Data Exchange (ETDEWEB)

    Procopio, Michael J.

    2010-04-01

    We present the Sandia Advanced Personnel Locator Engine (SAPLE) web application, a directory search application for use by Sandia National Laboratories personnel. SAPLE's purpose is to return Sandia personnel 'results' as a function of user search queries, with its mission to make it easier and faster to find people at Sandia. To accomplish this, SAPLE breaks from more traditional directory application approaches by aiming to return the correct set of results while placing minimal constraints on the user's query. Two key features form the core of SAPLE: advanced search query interpretation and inexact string matching. SAPLE's query interpretation permits the user to perform compound queries when typing into a single search field; where able, SAPLE infers the type of field that the user intends to search on based on the value of the search term. SAPLE's inexact string matching feature yields a high-quality ranking of personnel search results even when there are no exact matches to the user's query. This paper explores these two key features, describing in detail the architecture and operation of SAPLE. Finally, an extensive analysis on logged search query data taken from an 11-week sample period is presented.

  18. Update on NASA Microelectronics Activities

    Science.gov (United States)

    Label, Kenneth A.; Sampson, Michael J.; Casey, Megan; Lauenstein, Jean-Marie

    2017-01-01

    Mission Statement: The NASA Electronic Parts and Packaging (NEPP) Program provides NASA's leadership for developing and maintaining guidance for the screening, qualification, test. and usage of EEE parts by NASA as well as in collaboration with other government Agencies and industry. NASA Space Technology Mission Directorate (STMD) "STMD rapidly develops, demonstrates, and infuses revolutionary, high-payoff technologies through transparent, collaborative partnerships, expanding the boundaries of the aerospace enterprise." Mission Statement: The Space Environments Testing Management Office (SETMO) will identify, prioritize, and manage a select suite of Agency key capabilities/assets that are deemed to be essential to the future needs of NASA or the nation, including some capabilities that lack an adequate business base over the budget horizon. NESC mission is to perform value-added independent testing, analysis, and assessments of NASA's high-risk projects to ensure safety and mission success. NASA Space Environments and Avionics Fellows as well as Radiation and EEE Parts Community of Practice (CoP) leads.

  19. Understanding microelectronics a top-down approach

    CERN Document Server

    Maloberti, Franco

    2011-01-01

    The microelectronics evolution has given rise to many modern benefits but has also changed design methods and attitudes to learning. Technology advancements shifted focus from simple circuits to complex systems with major attention to high-level descriptions. The design methods moved from a bottom-up to a top-down approach. For today's students, the most beneficial approach to learning is this top-down method that demonstrates a global view of electronics before going into specifics. Franco Maloberti uses this approach to explain the fundamentals of electronics, such as processing functions,

  20. Porous low dielectric constant materials for microelectronics.

    Science.gov (United States)

    Baklanov, Mikhail R; Maex, Karen

    2006-01-15

    Materials with a low dielectric constant are required as interlayer dielectrics for the on-chip interconnection of ultra-large-scale integration devices to provide high speed, low dynamic power dissipation and low cross-talk noise. The selection of chemical compounds with low polarizability and the introduction of porosity result in a reduced dielectric constant. Integration of such materials into microelectronic circuits, however, poses a number of challenges, as the materials must meet strict requirements in terms of properties and reliability. These issues are the subject of the present paper.

  1. Dopant materials used in the microelectronics industry.

    Science.gov (United States)

    Lewis, D R

    1986-01-01

    Advances in microelectronics have transformed the occupational environment of the electronics industry. Large quantities of potentially hazardous materials are now in routine use as integrated circuit manufacturing becomes more complex and specialized. While the acute hazards associated with these dopant materials are clear, the subacute and chronic effects are less evident. Many of these elements are trace elements in humans and may play roles in health and disease in minute concentrations. Early detection and prevention of adverse health effects requires both astute medical surveillance, industrial hygiene, and safety engineering efforts to eliminate the sources of exposure to workers.

  2. Porous Dielectrics in Microelectronic Wiring Applications

    Directory of Open Access Journals (Sweden)

    Vincent McGahay

    2010-01-01

    Full Text Available Porous insulators are utilized in the wiring structure of microelectronic devices as a means of reducing, through low dielectric permittivity, power consumption and signal delay in integrated circuits. They are typically based on low density modifications of amorphous SiO2 known as SiCOH or carbon-doped oxides, in which free volume is created through the removal of labile organic phases. Porous dielectrics pose a number of technological challenges related to chemical and mechanical stability, particularly in regard to semiconductor processing methods. This review discusses porous dielectric film preparation techniques, key issues encountered, and mitigation strategies.

  3. Microphotonics systems: life beyond microelectronics

    Science.gov (United States)

    Eshraghian, Kamran; Alameh, Kamal

    2004-03-01

    In 1959, the physicist Richard Feynman advised his colleagues that "there's plenty of room at the bottom." He envisioned a discipline devoted to manipulating smaller and smaller units of matter. "I am not afraid," he wrote, "to consider the final question as to whether, ultimately -- in the great future -- we can arrange the atoms the way we want, the way very atoms, all the way down." However, in early 1980's the doom and gloom of silicon MOS transistors was foreshadowed and scaling of the humble MOS transistors beyond 140 nm appeared as the impossible dream. Manipulation of material science, the emergence of low-K material and copper technology together with new techniques in lithography and processing have paved the way for revised predication that has foreshadowed the feature sizes in the order of 20 nm - 30 nm will occur somewhere between 2012 and 2016. Coupled with these developments, nanochemists have began to probe into matter and now Nanochemistry is beginning to shape the future of new materials and better understand the unique properties of assemblies of atoms and molecules on a scale that range between that of individual building blocks and the bulk material, thus confirming Feynman's vision. At this level quantum effects can be significant and innovative ways of carrying out chemical reactions become possible.

  4. Micro-Electronic Nose System

    Science.gov (United States)

    Zee, Frank C.

    2011-12-01

    The ability to "smell" various gas vapors and complex odors is important for many applications such as environmental monitoring for detecting toxic gases as well as quality control in the processing of food, cosmetics, and other chemical products for commercial industries. Mimicking the architecture of the biological nose, a miniature electronic nose system was designed and developed consisting of an array of sensor devices, signal-processing circuits, and software pattern-recognition algorithms. The array of sensors used polymer/carbon-black composite thin-films, which would swell or expand reversibly and reproducibly and cause a resistance change upon exposure to a wide variety of gases. Two types of sensor devices were fabricated using silicon micromachining techniques to form "wells" that confined the polymer/carbon-black to a small and specific area. The first type of sensor device formed the "well" by etching into the silicon substrate using bulk micromachining. The second type built a high-aspect-ratio "well" on the surface of a silicon wafer using SU-8 photoresist. Two sizes of "wells" were fabricated: 500 x 600 mum² and 250 x 250 mum². Custom signal-processing circuits were implemented on a printed circuit board and as an application-specific integrated-circuit (ASIC) chip. The circuits were not only able to measure and amplify the small resistance changes, which corresponded to small ppm (parts-per-million) changes in gas concentrations, but were also adaptable to accommodate the various characteristics of the different thin-films. Since the thin-films were not specific to any one particular gas vapor, an array of sensors each containing a different thin-film was used to produce a distributed response pattern when exposed to a gas vapor. Pattern recognition, including a clustering algorithm and two artificial neural network algorithms, was used to classify the response pattern and identify the gas vapor or odor. Two gas experiments were performed, one

  5. A progress report on the LDRD project entitled {open_quotes}Microelectronic silicon-based chemical sensors: Ultradetection of high value molecules{close_quotes}

    Energy Technology Data Exchange (ETDEWEB)

    Hughes, R.C.

    1996-09-01

    This work addresses a new kind of silicon based chemical sensor that combines the reliability and stability of silicon microelectronic field effect devices with the highly selective and sensitive immunoassay. The sensor works on the principle that thin SiN layers on lightly doped Si can detect pH changes rapidly and reversibly. The pH changes affect the surface potential, and that can be quickly determined by pulsed photovoltage measurements. To detect other species, chemically sensitive films were deposited on the SiN where the presence of the chosen analyte results in pH changes through chemical reactions. A invention of a cell sorting device based on these principles is also described. A new method of immobilizing enzymes using Sandia`s sol-gel glasses is documented and biosensors based on the silicon wafer and an amperometric technique are detailed.

  6. A Vacuum Microelectronic Pressure Sensor Array Integrated with Temperature Sensor

    Institute of Scientific and Technical Information of China (English)

    SU Jie; XIA Shanhong; CHEN Shaofeng

    2001-01-01

    This paper presents a microsystemthat integrates a Vacuum Microelectronic pressuresensor array with a temperature sensor. The Vac-uum Microelectronic pressure sensor array consists of4 × 4 sensing elements. The temperature sensor is aPt-thin-film resistor. Computer aided design is usedto optimize the structure.

  7. Moving Education and Its Administration into the Microelectronic Age.

    Science.gov (United States)

    Culbertson, Jack A.

    Education is in transition between the ascendent microelectronic and descendent industrial revolutions, with purposes ambiguously linked to both. These purposes must be clarified before educational leaders can establish priorities for adapting education to the needs of a society transformed by microelectronic technology. Accordingly, the features…

  8. Microelectronics in the Curriculum--The Science Teacher's Contribution.

    Science.gov (United States)

    Association for Science Education, Cambridge (England).

    Rapid advances in microelectronics over the past few years have generally been beneficial, but they have also created some problems, and questions must be asked about the philosophy for including aspects of the new technology in the school curriculum. This statement, prepared by the Microelectronics and Science Education Subcommittee of the…

  9. Self-healable electrically conducting wires for wearable microelectronics.

    Science.gov (United States)

    Sun, Hao; You, Xiao; Jiang, Yishu; Guan, Guozhen; Fang, Xin; Deng, Jue; Chen, Peining; Luo, Yongfeng; Peng, Huisheng

    2014-09-01

    Electrically conducting wires play a critical role in the advancement of modern electronics and in particular are an important key to the development of next-generation wearable microelectronics. However, the thin conducting wires can easily break during use, and the whole device fails to function as a result. Herein, a new family of high-performance conducting wires that can self-heal after breaking has been developed by wrapping sheets of aligned carbon nanotubes around polymer fibers. The aligned carbon nanotubes offer an effective strategy for the self-healing of the electric conductivity, whereas the polymer fiber recovers its mechanical strength. A self-healable wire-shaped supercapacitor fabricated from a wire electrode of this type maintained a high capacitance after breaking and self-healing.

  10. [Application of microelectronics CAD tools to synthetic biology].

    Science.gov (United States)

    Madec, Morgan; Haiech, Jacques; Rosati, Élise; Rezgui, Abir; Gendrault, Yves; Lallement, Christophe

    2017-02-01

    Synthetic biology is an emerging science that aims to create new biological functions that do not exist in nature, based on the knowledge acquired in life science over the last century. Since the beginning of this century, several projects in synthetic biology have emerged. The complexity of the developed artificial bio-functions is relatively low so that empirical design methods could be used for the design process. Nevertheless, with the increasing complexity of biological circuits, this is no longer the case and a large number of computer aided design softwares have been developed in the past few years. These tools include languages for the behavioral description and the mathematical modelling of biological systems, simulators at different levels of abstraction, libraries of biological devices and circuit design automation algorithms. All of these tools already exist in other fields of engineering sciences, particularly in microelectronics. This is the approach that is put forward in this paper.

  11. Microelectronics effects as seen on CRRES.

    Science.gov (United States)

    Mullen, E G; Ray, K P

    1994-10-01

    A MicroElectronics Test Package (MEP) measured total dose degradation and single event upsets (SEUs) on 60 device types on the Combined Release and Radiation Effects Satellite (CRRES) in an 18 degrees inclination orbit between 350 km and 36000 km from July 1990 to October 1991. Simultaneous measurements of the high energy particle environment were used to make a direct cause and effect comparison of the energetic particle backgrounds and microelectronic performance characteristics. The galactic cosmic ray background for the period of the CRRES mission was at a minimum. The SEUs experienced from the cosmic ray background were correspondingly few in number, but surprisingly produced an equal probability of upset over an L-shell range of 8.5 Earth radii (RE) down to less than 3.0 RE. Cosmic ray induced upset frequencies in proton sensitive chips were over 2 orders of magnitude lower than those produced by protons in the heart of the inner proton radiation belts. Multiple upsets, those produced when a single particle upsets more than one memory location, were just as common from protons as from cosmic rays.

  12. Wireless Integrated Microelectronic Vacuum Sensor System

    Science.gov (United States)

    Krug, Eric; Philpot, Brian; Trott, Aaron; Lawrence, Shaun

    2013-01-01

    NASA Stennis Space Center's (SSC's) large rocket engine test facility requires the use of liquid propellants, including the use of cryogenic fluids like liquid hydrogen as fuel, and liquid oxygen as an oxidizer (gases which have been liquefied at very low temperatures). These fluids require special handling, storage, and transfer technology. The biggest problem associated with transferring cryogenic liquids is product loss due to heat transfer. Vacuum jacketed piping is specifically designed to maintain high thermal efficiency so that cryogenic liquids can be transferred with minimal heat transfer. A vacuum jacketed pipe is essentially two pipes in one. There is an inner carrier pipe, in which the cryogenic liquid is actually transferred, and an outer jacket pipe that supports and seals the vacuum insulation, forming the "vacuum jacket." The integrity of the vacuum jacketed transmission lines that transfer the cryogenic fluid from delivery barges to the test stand must be maintained prior to and during engine testing. To monitor the vacuum in these vacuum jacketed transmission lines, vacuum gauge readings are used. At SSC, vacuum gauge measurements are done on a manual rotation basis with two technicians, each using a handheld instrument. Manual collection of vacuum data is labor intensive and uses valuable personnel time. Additionally, there are times when personnel cannot collect the data in a timely fashion (i.e., when a leak is detected, measurements must be taken more often). Additionally, distribution of this data to all interested parties can be cumbersome. To simplify the vacuum-gauge data collection process, automate the data collection, and decrease the labor costs associated with acquiring these measurements, an automated system that monitors the existing gauges was developed by Invocon, Inc. For this project, Invocon developed a Wireless Integrated Microelectronic Vacuum Sensor System (WIMVSS) that provides the ability to gather vacuum

  13. Prototype dish testing and analysis at Sandia National Laboratories

    Science.gov (United States)

    Grossman, J. W.; Houser, R. M.; Erdman, W. W.

    1991-12-01

    During the past year, Sandia National Laboratories performed on-sun testing of several dish concentrator concepts. These tests were undertaken at the National Solar Thermal Test Facility (NSTTF). Two of the tests were performed in support of the DOE Concentrator Receiver Development Program. The first was on-sun testing of the single-element stretched-membrane dish; this 7-meter diameter dish uses a single preformed metal membrane with an aluminized polyester optical surface and shows potential for future dish-Stirling systems. The next involved two prototype facets from the Faceted Stretched-Membrane Dish Program. These facets, representing competitive design concepts, are closest to commercialization. Five 1-meter triangular facets were tested on-sun as part of the development program for a solar dynamic system on Space Station Freedom. While unique in character, all the tests utilized the Beam Characterization System (BCS) as the main measurement tool and all were analyzed using the Sandia-developed CIRCE2 computer code. The BCS is used to capture and digitize an image of the reflected concentrator beam that is incident on a target surface. The CIRCE2 program provides a computational tool, which when given the geometry of the concentrator and target as well as other design parameters will predict the flux distribution of the reflected beam. One of these parameters, slope error, is the variable that has a major effect in determining the quality of the reflected beam. The methodology used to combine these two tools to predict uniform slope errors for the dishes is discussed in this document. As the Concentrator Development Programs continue, Sandia will test and evaluate two prototype dish systems. The first, the faceted stretched-membrane dish, is expected to be tested in 1992, followed by the full-scale single-element stretched-membrane dish in 1993. These tests will use the tools and methodology discussed in this document.

  14. Effects of Vapor Pressure and Super-Hydrophobic Nanocomposite Coating on Microelectronics Reliability

    Directory of Open Access Journals (Sweden)

    Xuejun Fan

    2015-09-01

    Full Text Available Modeling vapor pressure is crucial for studying the moisture reliability of microelectronics, as high vapor pressure can cause device failures in environments with high temperature and humidity. To minimize the impact of vapor pressure, a super-hydrophobic (SH coating can be applied on the exterior surface of devices in order to prevent moisture penetration. The underlying mechanism of SH coating for enhancing device reliability, however, is still not fully understood. In this paper, we present several existing theories for predicting vapor pressure within microelectronic materials. In addition, we discuss the mechanism and effectiveness of SH coating in preventing water vapor from entering a device, based on experimental results. Two theoretical models, a micro-mechanics-based whole-field vapor pressure model and a convection-diffusion model, are described for predicting vapor pressure. Both methods have been successfully used to explain experimental results on uncoated samples. However, when a device was coated with an SH nanocomposite, weight gain was still observed, likely due to vapor penetration through the SH surface. This phenomenon may cast doubt on the effectiveness of SH coatings in microelectronic devices. Based on current theories and the available experimental results, we conclude that it is necessary to develop a new theory to understand how water vapor penetrates through SH coatings and impacts the materials underneath. Such a theory could greatly improve microelectronics reliability.

  15. History of Sandia National Laboratories` auxiliary closure mechanisms

    Energy Technology Data Exchange (ETDEWEB)

    Weydert, J.C. [Sandia National Labs., Albuquerque, NM (United States); Ponder, G.M. [Geo-Centers, Inc., Albuquerque, NM (United States)

    1993-12-01

    An essential component of a horizontal, underground nuclear test setup at the Nevada Test Site is the auxiliary closure system. The massive gates that slam shut immediately after a device has been detonated allow the prompt radiation to pass, but block debris and hot gases from continuing down the tunnel. Thus, the gates protect experiments located in the horizontal line-of-sight steel pipe. Sandia National Laboratories has been the major designer and developer of these closure systems. This report records the history of SNL`s participation in and contributions to the technology of auxiliary closure systems used in horizontal tunnel tests in the underground test program.

  16. Vibration control for precision manufacturing at Sandia National Laboratories

    Science.gov (United States)

    Hinnerichs, Terry D.; Martinez, David R.

    1995-05-01

    Sandia National Laboratories performs R&D in structural dynamics and vibration suppression of precision applications in weapon systems, space, underwater, transportation and civil structures. Over the last decade these efforts have expanded into the areas of active vibration control and 'smart' structures and material systems, In addition, major resources have been focused towards technology to support weapon product development and agile manufacturing capability for defense and industrial applications. This paper will briefly describe the structural dynamics modeling and verification process that supports vibration control and some specific applications of these techniques to manufacturing in the areas of lithography, machine tools and flexible robotics.

  17. 1990 DOE/SANDIA crystalline photovoltaic technology project review meeting

    Energy Technology Data Exchange (ETDEWEB)

    Ruby, D.S. (ed.)

    1990-07-01

    This document serves as the proceedings for the annual project review meeting held by Sandia's Photovoltaic Cell Research Division and Photovoltaic Technology Division. It contains information supplied by each organization making a presentation at the meeting, which was held August 7 through 9, 1990 at the Sheraton Hotel in Albuquerque, New Mexico. Sessions were held to discuss national photovoltaic programs, one-sun crystalline silicon cell research, concentrator silicon cell research, concentrator 3-5 cell research, and concentrating collector development.

  18. Experimental investigation of single-phase microjet cooling of microelectronics

    Directory of Open Access Journals (Sweden)

    Rusowicz Artur

    2015-09-01

    Full Text Available Development of electronics, which aims to improve the functionality of electronic devices, aims at increasing the packing of transistors in a chip and boosting clock speed (the number of elementary operations per second. While pursuing this objective, one encounters the growing problem of thermal nature. Each switching of the logic state at the elementary level of an integrated circuit is associated with the generation of heat. Due to a large number of transistors and high clock speeds, higher heat flux is emitted by the microprocessor to a level where the component needs to be intensively cooled, or otherwise it will become overheated. This paper presents the cooling of microelectronic components using microjets.

  19. Using microelectronics technology to communicate with living cells.

    Science.gov (United States)

    Heer, F; Hafizovic, S; Ugniwenko, T; Frey, U; Roscic, B; Blau, A; Hierlemann, A

    2007-01-01

    A monolithic microsystem in CMOS (complementary metal oxide semiconductor) technology is presented that provides bidirectional communication (stimulation and recording) between standard microelectronics and cultured electrogenic cells. The 128-electrode chip can be directly used as a substrate for cell culturing. It features circuitry units for stimulation and immediate cell signal treatment near each electrode. In addition, it provides on-chip A/D conversion as well as a digital interface so that a fast interaction is possible at good signal quality. Spontaneous and stimulated electrical activity recordings with neuronal and cardiac cell cultures will be presented. The system can be used to, e.g., study the behavior and development of neural networks in vitro, to reveal the effects of neuronal plasticity and to study network activity in response to pharmacological treatments.

  20. Sandia National Laboratories focus issue: introduction.

    Science.gov (United States)

    Boye, Robert

    2014-08-20

    For more than six decades, Sandia has provided the critical science and technology to address the nation's most challenging issues. Our original nuclear weapons mission has been complemented with work in defense systems, energy and climate, as well as international and homeland security. Our vision is to be a premier science and engineering laboratory for technology solutions to the most challenging problems that threaten peace and freedom for our nation and the globe.

  1. Liver enzymes among microelectronics equipment maintenance technicians.

    Science.gov (United States)

    Upfal, M

    1992-04-01

    Equipment maintenance workers within the microelectronics industry have opportunities for occupational exposure to a variety of toxic agents. This pilot investigation compares liver enzymes in this population with that of other coworkers. Participants (n = 135) were randomly selected from a medical surveillance program at the manufacturing facility. Nine job categories were examined, including equipment maintenance workers and electronic technicians. Although abnormal liver enzymes were detected among equipment maintenance workers (odds ratio 16.4; P less than .008) and electronic technicians (odds ratio 27; P less than .0005), the numbers of participants were small (n = 8, 10). The data suggest that independent and/or interactive etiologic roles of occupation and alcohol should be further investigated. Early detection of subclinical occupational or recreational hepatotoxicity with appropriate employment of industrial hygiene control technology and/or the reduction of alcohol consumption may provide a means of preventing liver disease.

  2. Dimensionally Stable Poyimide Copolymers for Microelectronics Applications

    Science.gov (United States)

    Fay, Catherine C.; St.Clair, Anne K.

    1998-01-01

    Polyimides are finding increased applications in microelectronics due to their high thermal stability, good chemical resistance, good adhesion, low moisture absorption, good mechanical properties, and low coefficient of thermal expansion (CTE). Four series of random copolyimides were synthesized and characterized for potential application as encapsulants, stress-relief layers, and interlevel dielectrics. Several candidates exhibited good combinations of physical and mechanical properties with inherent viscosities from 1.21 to 1.42 dL/g, T(sub g)'s ranging from 251 to 277 C, 10% weight loss temperatures between 503 and 527 C, and CTEs ranging from 33 to 39 ppm/deg C. Mechanical properties at room temperature for the best candidates included tensile strengths of 17.8-21.3 ksi, moduli between 388 and 506 ksi, and elongations of 11-43%. Moisture absorption for these copolyimides ranged between 0.85 and 1.38 wt %.

  3. RF and mm-Wave Photonics at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Vawter, G.A.; Sullivan, C.

    1999-07-08

    RF and mm-wave photonic devices and circuits have been developed at Sandia National Laboratories for applications ranging from RF optical data links to optical generation of mm-wave frequencies. This talk will explore recent high-speed photonics technology developments at Sandia including: (1) A monolithic optical integrated circuit for all-optical generation of mm-waves. Using integrated mode-locked diode lasers, amplifiers, and detectors, frequencies between 30 GHz and 90 GHz are generated by a single monolithic (Al,Ga)As optical circuit less than 2mm in its largest dimension. (2) Development of polarization-maintaining, low-insertion-loss, low v-pi, Mach-Zehnder interferometer (MZI) modulators with DC-to-potentially-K-band modulation bandwidth. New low-loss polarization-maintaining waveguide designs using binary alloys have been shown to reduce polarization crosstalk in undoped (Al,Ga)As waveguides, yielding high extinction ratio (>40dB) and low on-chip loss (<6dB) in Mach-Zehnder interferometers. RF drive voltage is reduced through use of 45rnrn-active length devices with modulator sensitivity, v-pi, less than 3V.

  4. Modeling biology with HDL languages: a first step toward a genetic design automation tool inspired from microelectronics.

    Science.gov (United States)

    Gendrault, Yves; Madec, Morgan; Lallement, Christophe; Haiech, Jacques

    2014-04-01

    Nowadays, synthetic biology is a hot research topic. Each day, progresses are made to improve the complexity of artificial biological functions in order to tend to complex biodevices and biosystems. Up to now, these systems are handmade by bioengineers, which require strong technical skills and leads to nonreusable development. Besides, scientific fields that share the same design approach, such as microelectronics, have already overcome several issues and designers succeed in building extremely complex systems with many evolved functions. On the other hand, in systems engineering and more specifically in microelectronics, the development of the domain has been promoted by both the improvement of technological processes and electronic design automation tools. The work presented in this paper paves the way for the adaptation of microelectronics design tools to synthetic biology. Considering the similarities and differences between the synthetic biology and microelectronics, the milestones of this adaptation are described. The first one concerns the modeling of biological mechanisms. To do so, a new formalism is proposed, based on an extension of the generalized Kirchhoff laws to biology. This way, a description of all biological mechanisms can be made with languages widely used in microelectronics. Our approach is therefore successfully validated on specific examples drawn from the literature.

  5. Functional and operational requirements document : building 1012, Battery and Energy Storage Device Test Facility, Sandia National Laboratories, New Mexico.

    Energy Technology Data Exchange (ETDEWEB)

    Johns, William H.

    2013-11-01

    This report provides an overview of information, prior studies, and analyses relevant to the development of functional and operational requirements for electrochemical testing of batteries and energy storage devices carried out by Sandia Organization 2546, Advanced Power Sources R&D. Electrochemical operations for this group are scheduled to transition from Sandia Building 894 to a new Building located in Sandia TA-II referred to as Building 1012. This report also provides background on select design considerations and identifies the Safety Goals, Stakeholder Objectives, and Design Objectives required by the Sandia Design Team to develop the Performance Criteria necessary to the design of Building 1012. This document recognizes the Architecture-Engineering (A-E) Team as the primary design entity. Where safety considerations are identified, suggestions are provided to provide context for the corresponding operational requirement(s).

  6. An overview of semiconductor bridge, SCB, applications at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Bickes, R.W. Jr.; Grubelich, M.C.; Harris, S.M.; Merson, J.A.; Weinlein, J.H.

    1995-05-01

    The semiconductor bridge, SCB, developed by Sandia National Laboratories is a maturing technology now being used in several applications by Sandia customers. Most applications arose because of a need at the system level to provide explosive assemblies that were light weight, small volume, low cost and required small quantities of electrical energy to function -- for the purposes of this paper we define an explosive assembly to mean the combination of the firing set and an explosive component. As a result, and because conventional firing systems could not meet the stringent size, weight and energy requirements of our customers, we designed and are investigating SCB applications that range from devices for Sandia applications to igniters for fireworks. We present in this paper an overview of SCB technology with specific examples of the system designed for our customers to meet modern requirements that sophisticated explosive systems must satisfy in today`s market environments.

  7. Autonomy and Complexity at Sandia Executive Summary of Academic Alliance Workshop on Autonomy and Complex Systems.

    Energy Technology Data Exchange (ETDEWEB)

    Hayden, Nancy Kay [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kleban, Stephen D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-05-01

    Sandia has identified autonomy as a strategic initiative and an important area for providing national leadership. A key question is, “How might autonomy change how we think about the national security challenges we address and the kinds of solutions we deliver?” Three workshops at Sandia early in 2017 brought together internal stakeholders and potential academic partners in autonomy to address this question. The first focused on programmatic applications and needs. The second explored existing internal capabilities and research and development needs. This report summarizes the outcome of the third workshop, held March 3, 2017 in Albuquerque, NM, which engaged Academic Alliance partners in autonomy efforts at Sandia by discussing research needs and synergistic areas of interest within the complex systems and system modeling domains, and identifying opportunities for partnering on laboratory directed and other joint research opportunities.

  8. The Unilab Blue Chip Range for Introducing Microelectronics.

    Science.gov (United States)

    Jarvis, W. H.

    1981-01-01

    Discusses various topics in microelectronics to aid those teaching modern electronics for the first time, including, among others, the slang name "micro," attitudes of examining boards, rapid obsolescence of electronic devices, costs, analog systems, and digital systems. (SK)

  9. Virtual thermo-mechanical prototyping of microelectronics devices

    NARCIS (Netherlands)

    Van Driel, W.D.

    2007-01-01

    Microelectronics have pervaded our lives for the past fifty years, with massive penetration into health, mobility, safety and security, communications, education, entertainment and virtually every aspect of human lives. The main technology drivers that enabled this expansion are miniaturization and

  10. Reliability and qualification of advanced microelectronics for space applications

    Science.gov (United States)

    Kayali, S.

    2003-01-01

    This paper provides a discussion of the subject and an approach to establish a reliability and qualification methodology to facilitate the utilization of state-of-the-art advanced microelectronic devices and structures in high reliability applications.

  11. Microelectronics and nanoelectronics trends, and applications to HEP instrumentation

    CERN Document Server

    CERN. Geneva

    2004-01-01

    Lecture 1 : Microelectronics and HEP instrumentation CMOS technology has been the leading technology in microelectronics for more that 30 years thanks to its outstanding capability to miniaturization and low power consumption. A brief history of the microelectronics semiconductor industry is presented with applications for LEP and LHC experiments. Lecture 2: Future trends in microelectronics and nanoelectronics Trends in miniaturization point to the fabrication of ULSI nanoscale CMOS circuits by the end of the decade. Device issues and quantum effects in nanoscale MOS transistor will be discussed. Beyond CMOS technology, several technology avenues based on nanotechnology are under investigation. We will present some promising nanoelectronic devices and circuits based on Single Electron Tunneling (SET) transistor, nanowire, quantum dot and carbon nanotubes. Lecture 3: Monolithic pixel detectors Microvertex detectors for particle physics experiments currently uses hybrid silicon pixel detector. Novel emerging m...

  12. Sandia software guidelines. Volume 3. Standards, practices, and conventions

    Energy Technology Data Exchange (ETDEWEB)

    1986-07-01

    This volume is one in a series of Sandia Software Guidelines intended for use in producing quality software within Sandia National Laboratories. In consonance with the IEEE Standard for Software Quality Assurance Plans, this volume identifies software standards, conventions, and practices. These guidelines are the result of a collective effort within Sandia National Laboratories to define recommended deliverables and to document standards, practices, and conventions which will help ensure quality software. 66 refs., 5 figs., 6 tabs.

  13. A microelectronics approach for the ROSETTA surface science package

    Science.gov (United States)

    Sandau, Rainer (Editor); Alkalaj, Leon

    1996-01-01

    In relation to the Rosetta surface science package, the benefits of the application of advanced microelectronics packaging technologies and other output from the Mars environmental survey (MESUR) integrated microelectronics study are reported on. The surface science package will be designed to operate for tens of hours. Its limited mass and power consumption make necessary a highly integrated design with all the instruments and subunits operated from a centralized control and information management subsystem.

  14. Site Environmental Report for 2007: Sandia National Laboratories, California

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L. [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Environmental Management Dept.

    2008-06-01

    Sandia National Laboratories, California (SNL/CA) is a government-owned/contractor-operated laboratory. Sandia Corporation, a Lockheed Martin Company, operates the laboratory for the Department of Energy’s National Nuclear Security Administration (NNSA). The NNSA Sandia Site Office oversees operations at the site, using Sandia Corporation as a management and operating contractor. This Site Environmental Report for 2007 was prepared in accordance with DOE Order 231.1A (DOE 2004a). The report provides a summary of environmental monitoring information and compliance activities that occurred at SNL/CA during calendar year 2007. General site and environmental program information is also included.

  15. Site environmental report for 2003 Sandia National Laboratories, California.

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L.

    2004-06-01

    Sandia National Laboratories, California (SNL/CA) is a government-owned/contractor-operated laboratory. Sandia Corporation, a Lockheed Martin Company, operates the laboratory for the Department of Energy's (DOE) National Nuclear Security Administration. The DOE Sandia Site Office oversees operations at the site, using Sandia Corporation as a management and operating contractor. This Site Environmental Report for 2003 was prepared in accordance with DOE Order 231.1A. The report provides a summary of environmental monitoring information and compliance activities that occurred at SNL/CA during calendar year 2003. General site and environmental program information is also included.

  16. Site environmental report for 2004 Sandia National Laboratories, California.

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L. (Sandia National Laboratories, Livermore, CA)

    2005-06-01

    Sandia National Laboratories, California (SNL/CA) is a government-owned/contractor-operated laboratory. Sandia Corporation, a Lockheed Martin Company, operates the laboratory for the Department of Energy's (DOE) National Nuclear Security Administration. The DOE Sandia Site Office oversees operations at the site, using Sandia Corporation as a management and operating contractor. This Site Environmental Report for 2004 was prepared in accordance with DOE Order 231.1A. The report provides a summary of environmental monitoring information and compliance activities that occurred at SNL/CA during calendar year 2004. General site and environmental program information is also included.

  17. Site environmental report for 2005 Sandia National Laboratories, California.

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L.

    2006-06-01

    Sandia National Laboratories, California (SNL/CA) is a government-owned/contractor-operated laboratory. Sandia Corporation, a Lockheed Martin Company, operates the laboratory for the Department of Energy's (DOE) National Nuclear Security Administration (NNSA). The DOE/NNSA Sandia Site Office (SSO) oversees operations at the site, using Sandia Corporation as a management and operating contractor. This Site Environmental Report for 2005 was prepared in accordance with DOE Order 231.1A. The report provides a summary of environmental monitoring information and compliance activities that occurred at SNL/CA during calendar year 2005. General site and environmental program information is also included.

  18. Site environmental report for 2006 Sandia National Laboratories, California.

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L.

    2007-06-01

    Sandia National Laboratories, California (SNL/CA) is a government-owned/contractor-operated laboratory. Sandia Corporation, a Lockheed Martin Company, operates the laboratory for the Department of Energy's National Nuclear Security Administration (NNSA). The NNSA Sandia Site Office oversees operations at the site, using Sandia Corporation as a management and operating contractor. This Site Environmental Report for 2006 was prepared in accordance with DOE Order 231.1A (DOE 2004a). The report provides a summary of environmental monitoring information and compliance activities that occurred at SNL/CA during calendar year 2006. General site and environmental program information is also included.

  19. Site environmental report for 2008 Sandia National Laboratories, California.

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L.

    2009-04-01

    Sandia National Laboratories, California (SNL/CA) is a government-owned/contractor operated laboratory. Sandia Corporation, a Lockheed Martin Company, operates the laboratory for the Department of Energy's National Nuclear Security Administration (NNSA). The NNSA Sandia Site Office oversees operations at the site, using Sandia Corporation as a management and operating contractor. This Site Environmental Report for 2008 was prepared in accordance with DOE Order 231.1A (DOE 2004a). The report provides a summary of environmental monitoring information and compliance activities that occurred at SNL/CA during calendar year 2008. General site and environmental program information is also included.

  20. Teamwork and diversity: A survey at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Apodaca, T.; Berman, M.; Griego, C.; Jansma, R.; Leatherwood, M.; Lovato, L.; Sanchez, A.

    1995-11-01

    In September, 1994, Sandia`s Diversity Leadership and Education Outreach Center arid the Corporate Diversity Team commissioned a Diversity Action Team (DAT-Phase II) to address the area of team- work. The goal of this DAT was to identify ways to capitalize on the diversity of people to enhance team success at Sandia. Given a six- month lifetime and funding levels of 12 hours per person per month, we chose to accomplish our goal by gathering and analyzing data on the performance and diversity of Sandia teams and publishing this report of our findings. The work presented herein builds on earlier work of this team.

  1. Power Supplies for Space Systems Quality Assurance by Sandia Laboratories

    Science.gov (United States)

    Hannigan, R. L.; Harnar, R. R.

    1976-07-01

    The Sandia Laboratories` participation in Quality Assurance programs for Radioisotopic Thermoelectric Generators which have been used in space systems over the past 10 years is summarized. Basic elements of this QA program are briefly described and recognition of assistance from other Sandia organizations is included. Descriptions of the various systems for which Sandia has had the QA responsibility are presented, including SNAP 19 (Nimbus, Pioneer, Viking), SNAP 27 (Apollo), Transit, Multi Hundred Watt (LES 8/9 and MJS), and a new program, High Performance Generator Mod 3. The outlook for Sandia participation in RTG programs for the next several years is noted.

  2. A History of Building 828, Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Ullrich, Rebecca

    1999-08-01

    This report documents the history of Building 828 in Sandia National Laboratories' Technical Area I. Building 828 was constructed in 1946 as a mechanical test laboratory for Los Alamos' Z-Division (later Sandia) as it moved to Sandia Base. The building has undergone significant remodeling over the years and has had a variety of occupants. The building was evaluated in compliance with the National Historic Preservation Act, but was not eligible for the National Register of Historic Places. Nevertheless, for many Labs employees, it was a symbol of Sandia's roots in World War II and the Manhattan Project.

  3. CALIBRATION OF DEVICES FOR MEASURING ELEMENTS OF MICRO-ELECTRONIC STRUCTURES

    OpenAIRE

    G. Trapashko

    2012-01-01

    Development of microelectronics requires solution of the problem ensuring unity of linear measurements in a submicron range. The problem can be solved on the condition that calibration of measuring devices shall be made in accordance with reference samples that is a short length scale.While making calibration of measuring equipment with the help of a reference measure it is important to investigate components of the method accuracy and their influence on measuring results. The paper considers...

  4. A flexible and robust soft-error testing system for microelectronic devices and integrated circuits

    Institute of Scientific and Technical Information of China (English)

    王晓辉; 杨振雷; 童腾; 苏弘; 刘杰; 张战刚; 古松; 刘天奇; 孔洁; 赵兴文

    2015-01-01

    Single event effects (SEEs) induced by radiations become a significant reliability challenge for modern elec-tronic systems. To evaluate SEEs susceptibility for microelectronic devices and integrated circuits (ICs), an SEE testing system with flexibility and robustness was developed at Heavy Ion Research Facility in Lanzhou (HIRFL). The system is compatible with various types of microelectronic devices and ICs, and supports plenty of complex and high-speed test schemes and plans for the irradiated devices under test (DUTs). Thanks to the combination of meticulous circuit design and the hardened logic design, the system has additional performances to avoid an overheated situation and irradiations by stray radiations. The system has been tested and verified by experiments for irradiating devices at HIRFL.

  5. 3D-Printed Disposable Wireless Sensors with Integrated Microelectronics for Large Area Environmental Monitoring

    KAUST Repository

    Farooqui, Muhammad Fahad

    2017-05-19

    Large area environmental monitoring can play a crucial role in dealing with crisis situations. However, it is challenging as implementing a fixed sensor network infrastructure over large remote area is economically unfeasible. This work proposes disposable, compact, dispersible 3D-printed wireless sensor nodes with integrated microelectronics which can be dispersed in the environment and work in conjunction with few fixed nodes for large area monitoring applications. As a proof of concept, the wireless sensing of temperature, humidity, and H2S levels are shown which are important for two critical environmental conditions namely forest fires and industrial leaks. These inkjet-printed sensors and an antenna are realized on the walls of a 3D-printed cubic package which encloses the microelectronics developed on a 3D-printed circuit board. Hence, 3D printing and inkjet printing are uniquely combined in order to realize a low-cost, fully integrated wireless sensor node.

  6. A case for Sandia investment in complex adaptive systems science and technology.

    Energy Technology Data Exchange (ETDEWEB)

    Colbaugh, Richard; Tsao, Jeffrey Yeenien; Johnson, Curtis Martin; Backus, George A.; Brown, Theresa Jean; Jones, Katherine A.

    2012-05-01

    This white paper makes a case for Sandia National Laboratories investments in complex adaptive systems science and technology (S&T) -- investments that could enable higher-value-added and more-robustly-engineered solutions to challenges of importance to Sandia's national security mission and to the nation. Complex adaptive systems are ubiquitous in Sandia's national security mission areas. We often ignore the adaptive complexity of these systems by narrowing our 'aperture of concern' to systems or subsystems with a limited range of function exposed to a limited range of environments over limited periods of time. But by widening our aperture of concern we could increase our impact considerably. To do so, the science and technology of complex adaptive systems must mature considerably. Despite an explosion of interest outside of Sandia, however, that science and technology is still in its youth. What has been missing is contact with real (rather than model) systems and real domain-area detail. With its center-of-gravity as an engineering laboratory, Sandia's has made considerable progress applying existing science and technology to real complex adaptive systems. It has focused much less, however, on advancing the science and technology itself. But its close contact with real systems and real domain-area detail represents a powerful strength with which to help complex adaptive systems science and technology mature. Sandia is thus both a prime beneficiary of, as well as potentially a prime contributor to, complex adaptive systems science and technology. Building a productive program in complex adaptive systems science and technology at Sandia will not be trivial, but a credible path can be envisioned: in the short run, continue to apply existing science and technology to real domain-area complex adaptive systems; in the medium run, jump-start the creation of new science and technology capability through Sandia's Laboratory Directed Research

  7. Sandia`s network for Supercomputing `94: Linking the Los Alamos, Lawrence Livermore, and Sandia National Laboratories using switched multimegabit data service

    Energy Technology Data Exchange (ETDEWEB)

    Vahle, M.O.; Gossage, S.A.; Brenkosh, J.P. [Sandia National Labs., Albuquerque, NM (United States). Advanced Networking Integration Dept.

    1995-01-01

    Supercomputing `94, a high-performance computing and communications conference, was held November 14th through 18th, 1994 in Washington DC. For the past four years, Sandia National Laboratories has used this conference to showcase and focus its communications and networking endeavors. At the 1994 conference, Sandia built a Switched Multimegabit Data Service (SMDS) network running at 44.736 megabits per second linking its private SMDS network between its facilities in Albuquerque, New Mexico and Livermore, California to the convention center in Washington, D.C. For the show, the network was also extended from Sandia, New Mexico to Los Alamos National Laboratory and from Sandia, California to Lawrence Livermore National Laboratory. This paper documents and describes this network and how it was used at the conference.

  8. 1992 DOE/Sandia crystalline photovoltaic technology project review meeting

    Energy Technology Data Exchange (ETDEWEB)

    Maish, A. [ed.

    1992-07-01

    This document serves as the proceedings for the annual project review meeting held by Sandia National Laboratories` Photovoltaic Technology and Photovoltaic Evaluation Departments. It contains information supplied by organizations making presentations at the meeting, which was held July 14--15, 1992 at the Sheraton Old Town Hotel in Albuquerque, New Mexico. Overview sessions covered the Department of Energy (DOE) program, including those at Sandia and the National Renewable Energy Laboratory (NREL), and non-DOE programs, including the EPRI concentrator collector program, The Japanese crystalline silicon program, and some concentrating photovoltaic activities in Europe. Additional sessions included papers on Sandia`s Photovoltaic Device Fabrication Laboratory`s collaborative research, cell processing research, the activities of the participants in the Concentrator Initiative Program, and photovoltaic technology evaluation at Sandia and NREL.

  9. Tonopah test range - outpost of Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, L.

    1996-03-01

    Tonopah Test Range is a unique historic site. Established in 1957 by Sandia Corporation, Tonopah Test Range in Nevada provided an isolated place for the Atomic Energy Commission to test ballistics and non-nuclear features of atomic weapons. It served this and allied purposes well for nearly forty years, contributing immeasurably to a peaceful conclusion to the long arms race remembered as the Cold War. This report is a brief review of historical highlights at Tonopah Test Range. Sandia`s Los Lunas, Salton Sea, Kauai, and Edgewood testing ranges also receive abridged mention. Although Sandia`s test ranges are the subject, the central focus is on the people who managed and operated the range. Comments from historical figures are interspersed through the narrative to establish this perspective, and at the end a few observations concerning the range`s future are provided.

  10. Massively Parallel Computing: A Sandia Perspective

    Energy Technology Data Exchange (ETDEWEB)

    Dosanjh, Sudip S.; Greenberg, David S.; Hendrickson, Bruce; Heroux, Michael A.; Plimpton, Steve J.; Tomkins, James L.; Womble, David E.

    1999-05-06

    The computing power available to scientists and engineers has increased dramatically in the past decade, due in part to progress in making massively parallel computing practical and available. The expectation for these machines has been great. The reality is that progress has been slower than expected. Nevertheless, massively parallel computing is beginning to realize its potential for enabling significant break-throughs in science and engineering. This paper provides a perspective on the state of the field, colored by the authors' experiences using large scale parallel machines at Sandia National Laboratories. We address trends in hardware, system software and algorithms, and we also offer our view of the forces shaping the parallel computing industry.

  11. Japanese technology assessment: Computer science, opto- and microelectronics mechatronics, biotechnology

    Energy Technology Data Exchange (ETDEWEB)

    Brandin, D.; Wieder, H.; Spicer, W.; Nevins, J.; Oxender, D.

    1986-01-01

    The series studies Japanese research and development in four high-technology areas - computer science, opto and microelectronics, mechatronics (a term created by the Japanese to describe the union of mechanical and electronic engineering to produce the next generation of machines, robots, and the like), and biotechnology. The evaluations were conducted by panels of U.S. scientists - chosen from academia, government, and industry - actively involved in research in areas of expertise. The studies were prepared for the purpose of aiding the U.S. response to Japan's technological challenge. The main focus of the assessments is on the current status and long-term direction and emphasis of Japanese research and development. Other aspects covered include evolution of the state of the art; identification of Japanese researchers, R and D organizations, and resources; and comparative U.S. efforts. The general time frame of the studies corresponds to future industrial applications and potential commercial impacts spanning approximately the next two decades.

  12. A bistable microelectronic circuit for sensing extremely low electric field

    Science.gov (United States)

    In, Visarath; Longhini, Patrick; Liu, Norman; Kho, Andy; Neff, Joseph D.; Palacios, Antonio; Bulsara, Adi R.

    2010-01-01

    Bistable systems are prevalently found in many sensor systems. Recently, we have explored (unidirectionally) coupled overdamped bistable systems that admit self-sustained oscillations when the coupling parameter is swept through the critical points of bifurcations [V. In et al., Phys. Rev. E 68, 045102-R (2003); A. R. Bulsara et al., Phys. Rev. E 70, 036103 (2004); V. In et al., Phys. Rev. E 72, 045104-R (2005); Phys Rev. Lett. 91, 244101 (2003); A. Palacios et al., Phys. Rev. E 72, 026211 (2005); V. In et al., Phys. Rev. E 73, 066121 (2006)]. Complex behaviors emerge, in addition, from these (relatively simple) coupled systems when an external signal (ac or dc) is applied uniformly to all the elements in the array. In particular, we have demonstrated this emergent behavior for a coupled system comprised of mean-field hysteretic elements describing a "single-domain" ferromagnetic sample. The results are being used to develop extremely sensitive magnetic sensors capable of resolving field changes as low as 150 pT by observing the changes in the oscillation characteristics of the coupled sensors. In this paper, we explore the underlying dynamics of a coupled bistable system realized by coupling microelectronic circuits, which belong to the same class of dynamics as the aforementioned (ferromagnetic) system, with the nonlinear features and coupling terms modeled by hyperbolic tangent nonlinearities; these nonlinearities stem from the operational transconductance amplifiers used in constructing the microcircuits. The emergent behavior is being applied to develop an extremely sensitive electric-field sensor.

  13. Assessing Advanced High School and Undergraduate Students' Thinking Skills: The Chemistry--From the Nanoscale to Microelectronics Module

    Science.gov (United States)

    Dori, Yehudit Judy; Dangur, Vered; Avargil, Shirly; Peskin, Uri

    2014-01-01

    Chemistry students in Israel have two options for studying chemistry: basic or honors (advanced placement). For instruction in high school honors chemistry courses, we developed a module focusing on abstract topics in quantum mechanics: Chemistry--From the Nanoscale to Microelectronics. The module adopts a visual-conceptual approach, which…

  14. Assessing Advanced High School and Undergraduate Students' Thinking Skills: The Chemistry--From the Nanoscale to Microelectronics Module

    Science.gov (United States)

    Dori, Yehudit Judy; Dangur, Vered; Avargil, Shirly; Peskin, Uri

    2014-01-01

    Chemistry students in Israel have two options for studying chemistry: basic or honors (advanced placement). For instruction in high school honors chemistry courses, we developed a module focusing on abstract topics in quantum mechanics: Chemistry--From the Nanoscale to Microelectronics. The module adopts a visual-conceptual approach, which…

  15. Sandia National Laboratories, California sewer system management plan.

    Energy Technology Data Exchange (ETDEWEB)

    Holland, Robert C.

    2010-02-01

    A Sewer System Management Plan (SSMP) is required by the State Water Resources Control Board (SWRCB) Order No. 2006-0003-DWQ Statewide General Waste Discharge Requirements (WDR) for Sanitary Sewer Systems (General Permit). DOE, National Nuclear Security Administration (NNSA), Sandia Site Office has filed a Notice of Intent to be covered under this General Permit. The General Permit requires a proactive approach to reduce the number and frequency of sanitary sewer overflows (SSOs) within the State. SSMPs must include provisions to provide proper and efficient management, operation, and maintenance of sanitary sewer systems and must contain a spill response plan. Elements of this Plan are under development in accordance with the SWRCB's schedule.

  16. Road vehicle-induced vibration control of microelectronics facilities

    Institute of Scientific and Technical Information of China (English)

    Guo Anxin; Xu Youlin; Li Hui

    2005-01-01

    A hybrid control platform is investigated in this paper to mitigate microvibrations to a group of vibrationsensitive equipment installed in a microelectronics facility subject to nearby road vehicle-induced horizontal and vertical ground motions. The hybrid control platform, on which microelectronics equipment is installed, is mounted on a building floor through a series of passive mounts and controlled by hydraulic actuators in both horizontal and vertical directions. The control platform is an elastic body with significant bending modes of vibration, and a sub-optimal control algorithm is used to manipulate the hydraulic actuators with actuator dynamics included. The finite element model and the equations of motion of the coupled platform-building system are then established in the absolute coordinate to facilitate the feedback control and performance evaluation of the platform. The horizontal and vertical ground vibrations at the base of the building induced by nearby moving road vehicles are assumed to be stationary random processes. A typical three-story microelectronics building is selected as a case study. The case study shows that the vertical vibration of the microelectronics building is higher than the horizontal. The use of a hybrid control platform can effectively reduce both horizontal and vertical microvibrations of the microelectronics equipment to the level which satisfies the stringent microscale velocity requirement specified in the Bolt Beranek & Newman (BBN) criteria.

  17. Development of the ANL plant dynamics code and control strategies for the supercritical carbon dioxide Brayton cycle and code validation with data from the Sandia small-scale supercritical carbon dioxide Brayton cycle test loop.

    Energy Technology Data Exchange (ETDEWEB)

    Moisseytsev, A.; Sienicki, J. J. (Nuclear Engineering Division)

    2011-11-07

    Significant progress has been made in the ongoing development of the Argonne National Laboratory (ANL) Plant Dynamics Code (PDC), the ongoing investigation and development of control strategies, and the analysis of system transient behavior for supercritical carbon dioxide (S-CO{sub 2}) Brayton cycles. Several code modifications have been introduced during FY2011 to extend the range of applicability of the PDC and to improve its calculational stability and speed. A new and innovative approach was developed to couple the Plant Dynamics Code for S-CO{sub 2} cycle calculations with SAS4A/SASSYS-1 Liquid Metal Reactor Code System calculations for the transient system level behavior on the reactor side of a Sodium-Cooled Fast Reactor (SFR) or Lead-Cooled Fast Reactor (LFR). The new code system allows use of the full capabilities of both codes such that whole-plant transients can now be simulated without additional user interaction. Several other code modifications, including the introduction of compressor surge control, a new approach for determining the solution time step for efficient computational speed, an updated treatment of S-CO{sub 2} cycle flow mergers and splits, a modified enthalpy equation to improve the treatment of negative flow, and a revised solution of the reactor heat exchanger (RHX) equations coupling the S-CO{sub 2} cycle to the reactor, were introduced to the PDC in FY2011. All of these modifications have improved the code computational stability and computational speed, while not significantly affecting the results of transient calculations. The improved PDC was used to continue the investigation of S-CO{sub 2} cycle control and transient behavior. The coupled PDC-SAS4A/SASSYS-1 code capability was used to study the dynamic characteristics of a S-CO{sub 2} cycle coupled to a SFR plant. Cycle control was investigated in terms of the ability of the cycle to respond to a linear reduction in the electrical grid demand from 100% to 0% at a rate of 5

  18. Affective and personality disturbances among female former microelectronics workers.

    Science.gov (United States)

    Bowler, R M; Mergler, D; Rauch, S S; Harrison, R; Cone, J

    1991-01-01

    The production and manufacture of microelectronic components, carried out primarily by women workers, require extensive use of organic solvents. Affective and personality disturbances frequently have been associated with organic solvent toxicity. A group of women, former microelectronics workers (N = 70), primarily of Hispanic origin (77.1%) but raised in the United States, were evaluated for affective and personality disturbance with the MMPI. Profiles were analyzed, and diagnostic classification was performed blind. Results showed that (1) 85.7% of the profiles indicated abnormally high clinical elevations; and (2) MMPI profile classification revealed four clinical diagnostic groups: somatoform (24.3%), depression (15.7%), anxiety (28.6%), and psychotic (14.3%). These findings indicate significant psychopathology among these women, who formerly had worked in a microelectronics plant. The patterns of impairment present similarities to previous reports of organic solvent toxicity.

  19. Animal experiments with the microelectronics neural bridge IC.

    Science.gov (United States)

    Li, Wenyuan; Pei, Fei; Wang, Zhigong; Lü, Xiaoying

    2012-01-01

    The combination of the neural science and the microelectronics science offers a new way to restore the function of central nervous system. A neural regeneration module is used to be implanted into body to bridge the damaged nerve. A microelectronics neural bridge IC designed in CSMC 0.5□m CMOS process which can detect the neural signal and stimulate the nerve is presented. The neural regeneration module is composed of the microelectronics neural bridge IC and some discrete devices. An animal experiment has been done to check whether the neural signal can be transmitted with the chip normally or not. The animal experiment results suggest that the neural regeneration module can make the neural signal transmit normally.

  20. Potential occupational health hazards in the microelectronics industry.

    Science.gov (United States)

    LaDou, J

    1983-02-01

    The microelectronics industry is a major user of a wide variety of chemicals and other toxic materials. In the recent past semiconductor manufacturers have located in many countries and brought a new set of challenging clinical problems to occupational physicians. California, an area with a significant history in the statistical study of health and safety in the microelectronics industry, presents some evidence of potential health hazards in the semiconductor manufacturing process. The Semiconductor Industry Study done in California in 1981 explains the application of many toxic materials in the semiconductor manufacturing process, including a variety of solvents, acids, and metals such as arsenic. The Study documents the extensive use of dopant gases, primarily arsine, phosphine and diborane. Further study is necessary to assure the health and safety of microelectronics workers, particularly in the application of dopant gases.

  1. Multilayered Microelectronic Device Package With An Integral Window

    Science.gov (United States)

    Peterson, Kenneth A.; Watson, Robert D.

    2004-10-26

    A microelectronic package with an integral window mounted in a recessed lip for housing a microelectronic device. The device can be a semiconductor chip, a CCD chip, a CMOS chip, a VCSEL chip, a laser diode, a MEMS device, or a IMEMS device. The package can be formed of a low temperature co-fired ceramic (LTCC) or high temperature cofired ceramic (HTCC) multilayered material, with the integral window being simultaneously joined (e.g. co-fired) to the package body during LTCC or HTCC processing. The microelectronic device can be flip-chip bonded and oriented so that a light-sensitive side is optically accessible through the window. The result is a compact, low profile package, having an integral window mounted in a recessed lip, that can be hermetically sealed.

  2. Structure, properties, and MEMS and microelectronic applications of vanadium oxides

    Indian Academy of Sciences (India)

    Robert B Darling; Shiho Iwanaga

    2009-08-01

    Vanadium oxides have for many decades attracted much attention for their rich and unique physical properties which pose intriguing questions as to their fundamental origins as well as offering numerous potential applications for microelectronics, sensors, and microelectromechanical systems (MEMS). This paper reviews the unique structure and properties of the two most common vanadium oxides which have entered into microfabricated devices, VO2 and V25, and some of the past and future device applications which can be realized using these materials. Two emerging new materials, sodium vanadium bronzes and vanadium oxide nanotubes are also discussed for their potential use in new microelectronic devices.

  3. Site Environmental Report for 2012 Sandia National Laboratories California

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2013-05-01

    Sandia National Laboratories, California (SNL/CA) is a government-owned/contractor-operated laboratory. Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, manages and operates the laboratory for the Department of Energy’s National Nuclear Security Administration (NNSA). The NNSA Sandia Field Office administers the contract and oversees contractor operations at the site. This Site Environmental Report for 2012 was prepared in accordance with DOE Order 231.1B, Environment, Safety and Health Reporting (DOE 2011d). The report provides a summary of environmental monitoring information and compliance activities that occurred at SNL/CA during calendar year 2012. General site and environmental program information is also included.

  4. Site environmental report for 2011. Sandia National Laboratories, California

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2012-05-01

    Sandia National Laboratories, California (SNL/CA) is a government-owned/contractoroperated laboratory. Sandia Corporation, a wholly-owned subsidiary of Lockheed Martin Corporation, manages and operates the laboratory for the Department of Energy’s National Nuclear Security Administration (NNSA). The NNSA Sandia Site Office administers the contract and oversees contractor operations at the site. This Site Environmental Report for 2011 was prepared in accordance with DOE Order 231.1B, Environment, Safety and Health Reporting (DOE 2011d). The report provides a summary of environmental monitoring information and compliance activities that occurred at SNL/CA during calendar year 2011. General site and environmental program information is also included.

  5. [Modern hearing-aids at the cutting edge of microelectronics. Increased possibilities for individual customization].

    Science.gov (United States)

    Arlinger, S

    1999-08-25

    The development of modern hearing aids has been so great that they now represent the cutting edge of micro-electronics. Flexibility has been enhanced by computer-aided programming of the devices, and particularly by digital signal processing, developments which enable improved customization. Increased knowledge of the pathophysiology of the auditory system, fundamental processes in central auditory pathways, and cognitive function enable technological developments to be exploited, thus enhancing our ability to cope with an increasingly broad spectrum of hearing impairment, ranging from mild high-frequency loss to severe loss across the entire frequency range.

  6. Progress report of Sandia National Laboratories (SNL) contribu- tion to IAEA CRP F11016 on ?Utilization of ion accelerators for studying and modeling of radiation induced defects in semicon- ductors and insulators? 3rd RCM.

    Energy Technology Data Exchange (ETDEWEB)

    Vizkelethy, Gyorgy [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-10-01

    This report presents the results of Sandia National Laboratories’ (SNL) contribution to IAEA CRP F11016 as mostly raw data. The goal of this CRP is to study the effects of radiation on semiconductors and insulators with the emphasis on the effect of displacement damage due to MeV energy ions on the performance of semiconductor detectors and microelectronic devices. SNL is tasked with performing electrical characterization, irradiation, and IBIC, DLTS, C-­V measurements on devices used in the CRP, as well as calculating damage and ionization profiles for modeling.

  7. Radiation Testing at Sandia National Laboratories: Sandia – JPL Collaboration for Europa Lander

    Energy Technology Data Exchange (ETDEWEB)

    Hattar, Khalid Mikhiel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Ion Beam Lab.; Olszewska-Wasiolek, Maryla Aleksandra [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Gamma Irradiation Facility

    2017-01-01

    Sandia National Laboratories (SNL) is assisting Jet Propulsion Laboratory in undertaking feasibility studies and performance assessments for the Planetary Protection aspect of the Europa Lander mission. The specific areas of interest for this project are described by task number. This white paper presents the evaluation results for Task 2, Radiation Testing, which was stated as follows: Survey SNL facilities and capabilities for simulating the Europan radiation environment and assess suitability for: A. Testing batteries, electronics, and other component and subsystems B. Exposing biological organisms to assess their survivability metrics.

  8. Site Environmental Report for 2016 Sandia National Laboratories California.

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2017-06-01

    Sandia National Laboratories, California (SNL/CA) is a Department of Energy (DOE) facility. The management and operations of the facility are under a contract with the DOE’s National Nuclear Security Administration (NNSA). On May 1, 2017, the name of the management and operating contractor changed from Sandia Corporation to National Technology and Engineering Solutions of Sandia, LLC (NTESS). The DOE, NNSA, Sandia Field Office administers the contract and oversees contractor operations at the site. This Site Environmental Report for 2016 was prepared in accordance with DOE Order 231.1B, Environment, Safety and Health Reporting (DOE 2012). The report provides a summary of environmental monitoring information and compliance activities that occurred at SNL/CA during calendar year 2016, unless noted otherwise. General site and environmental program information is also included.

  9. Integrating Microcomputers and Microelectronics into the Physics Curriculum.

    Science.gov (United States)

    Gale, Douglas S.

    1980-01-01

    Describes an interdisciplinary microcomputer and microelectronics program offered jointly by the Physics and Computer Science Departments of East Texas State University. The program operates on both the graduate and undergraduate level. Content as well as structure of the program are discussed. (Author/DS)

  10. Organic transistors in optical displays and microelectronic applications

    NARCIS (Netherlands)

    Gelinck, G.H.; Heremans, P.; Nomoto, K.; Anthopoulos, T.D.

    2010-01-01

    Organic thin-film transistors (OTFTs) offer unprecedented opportunities for implementation in a broad range of technological applications spanning from large-volume microelectronics and optical displays to chemical and biological sensors. In this Progress Report, we review the application of organic

  11. Technology integration project: Environmental Restoration Technologies Department Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Williams, C.V.; Burford, T.D. [Sandia National Labs., Albuquerque, NM (United States). Environmental Restoration Technologies; Allen, C.A. [Tech Reps, Inc., Albuquerque, NM (United States)

    1996-08-01

    Sandia National Laboratories Environmental Restoration Technologies Department is developing environmental restoration technologies through funding form the US Department of Energy`s (DOE`s) Office of Science and Technology. Initially, this technology development has been through the Mixed Waste Landfill Integrated Demonstration (MWLID). It is currently being developed through the Contaminant Plume containment and Remediation Focus Area, the Landfill Stabilization Focus Area, and the Characterization, Monitoring, and Sensor Cross-Cutting Program. This Technology Integration Project (TIP) was responsible for transferring MWLID-developed technologies for routine use by environmental restoration groups throughout the DOE complex and commercializing these technologies to the private sector. The MWLID`s technology transfer/commercialization successes were achieved by involving private industry in development, demonstration, and technology transfer/commercialization activities; gathering and disseminating information about MWLID activities and technologies; and promoting stakeholder and regulatory involvement. From FY91 through FY95, 30 Technical Task Plans (TTPs) were funded. From these TTPs, the MWLID can claim 15 technology transfer/commercialization successes. Another seven technology transfer/commercialization successes are expected. With the changeover to the focus areas, the TIP continued the technology transfer/commercialization efforts begun under the MWLID.

  12. Sandia National Laboratories Institutional Plan: FY 1999-2004

    Energy Technology Data Exchange (ETDEWEB)

    Garber, D.P.

    1999-01-06

    This Institutional Plan is the most comprehensive yearly "snapshot" available of Sandia National Laboratories' major programs, facilities, human resources, and budget. The document also includes overviews of our missions, organization, capabilities, planning functions, milestones, and accomplishments. The document's purpose is to provide the above information to the US Department of Energy, key congressional committees, Sandia management, and other present and potential customers. Chapter 2 presents information about Sandia's mission and summarizes our recent revision of Sandia's Strategic Plan. Chapter 3 presents an overview of Sandia's strategic objectives, chapter 4 lists laboratory goals and milestones for FY 1999, and chapter 5 presents our accomplishments during FY 1998. Chapters 3 through 5 are organized around our eight strategic objectives. The four primary objectives cover nuclear weapons responsibilities, nonproliferation and materials control, energy and critical infrastructures, and emerging national security threats. The major programmatic initiatives are presented in chapter 7. However, the programmatic descriptions in chapter 6 and the Associated funding tables in chapter 9 continue to be presented by DOE Budget and Reporting Code, as in previous Sandia institutional plans. As an aid to the reader, the four primary strategic objectives in chapter 3 are cross-referenced to the program information in chapter 6.

  13. Partnering with Sandia National Laboratories through alliances or consortia

    Energy Technology Data Exchange (ETDEWEB)

    Winchell, B.M.

    1994-12-01

    To better facilitate working with industry, groups of industrial participants, and partners in alliances or consortia, Sandia National Laboratories presents information helpful to those outside groups as to the forms of arrangements that may be used to better facilitate partnering relationships between Sandia National Laboratories and consortia or alliances of outside parties. It is expected that these alliances and consortia will include both large and small for-profit industrial concerns, as well as not-for-profit entities such as universities, institutes, other research facilities, and other nonprofit institutions or consortia containing institutions. The intent of this report is to provide such outside groups with information that will facilitate rapid interactions with Sandia National Laboratories through some of these forms of business which will be discussed in this report. These are not the only approaches to facilitating business interactions with Sandia National Laboratories and it is not intended that this report be legal advice or required approaches to doing business with Sandia National Laboratories. The intent of this report is merely to suggest ways in which Sandia National Laboratories can work with outside parties in the most expeditious manner.

  14. Partnering with Sandia National Laboratories through alliances or consortia

    Energy Technology Data Exchange (ETDEWEB)

    Winchell, B.M.

    1994-04-01

    To better facilitate working with industry, groups of industrial participants, and partners in alliances or consortia, Sandia National laboratories presents information helpful to those outside groups as to the forms of arrangements that may be used to better facilitate partnering relationships between Sandia National Laboratories and consortia or alliances of outside parties. It is expected that these alliances and consortia will include both large and small for-profit industrial concerns, as well as not-for-profit entities such as universities, institutes, other research facilities, and other nonprofit institutions or consortia containing institutions. The intent of this report is to provide such outside groups with information that will facilitate rapid interactions with Sandia National Laboratories through some of these forms of business which will be discussed in this report. These are not the only approaches to facilitating business interactions with Sandia National Laboratories and it is not intended that this report be legal advice or required approaches to doing business with Sandia National Laboratories. The intent of this report is merely to suggest ways in which Sandia National Laboratories can work with outside parties in the most expeditious manner.

  15. Plan for advanced microelectronics processing technology application. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Goland, A.N.

    1990-10-01

    The ultimate objective of the tasks described in the research agreement was to identify resources primarily, but not exclusively, within New York State that are available for the development of a Center for Advanced Microelectronics Processing (CAMP). Identification of those resources would enable Brookhaven National Laboratory to prepare a program plan for the CAMP. In order to achieve the stated goal, the principal investigators undertook to meet the key personnel in relevant NYS industrial and academic organizations to discuss the potential for economic development that could accompany such a Center and to gauge the extent of participation that could be expected from each interested party. Integrated of these discussions was to be achieved through a workshop convened in the summer of 1990. The culmination of this workshop was to be a report (the final report) outlining a plan for implementing a Center in the state. As events unfolded, it became possible to identify the elements of a major center for x-ray lithography on Lone Island at Brookhaven National Laboratory. The principal investigators were than advised to substitute a working document based upon that concept in place of a report based upon the more general CAMP workshop originally envisioned. Following that suggestion from the New York State Science and Technology Foundation, the principals established a working group consisting of representatives of the Grumman Corporation, Columbia University, the State University of New York at Stony Brook, and Brookhaven National Laboratory. Regular meetings and additional communications between these collaborators have produced a preproposal that constitutes the main body of the final report required by the contract. Other components of this final report include the interim report and a brief description of the activities which followed the establishment of the X-ray Lithography Center working group.

  16. Chemical Microsensor and Micro-Instrument Technology at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Butler, M.A.; Frye-Mason, G.C.; Hughes, R.C.; Osbourn, G.C.

    1999-03-26

    Important factors in the application of chemical sensing technology to space applications are low mass, small size, and low power. All of these attributes are enabled by the application of MEMS and micro-fabrication technology to chemical sensing. Several Sandia projects that apply these technologies to the development of new chemical sensing capabilities with the potential for space applications will be described. The Polychromator project is a joint project with Honeywell and MIT to develop an electrically programmable diffraction grating that can be programmed to synthesize the spectra of molecules. This grating will be used as the reference cell in a gas correlation radiometer to enable remote chemical detection of most chemical species. Another area of research where micro-fabrication is having a large impact is the development of a lab on a chip. Sandia's efforts to develop the {mu}ChemLab{trademark} will be described including the development of microfabricated pre-concentrators, chromatographic columns, and detectors. Chemical sensors are evolving in the direction of sensor arrays with pattern recognition methods applied to interpret the pattern of response. Sandia's development of micro-fabricated chemiresistor arrays and the VERI pattern recognition technology to interpret the sensor response will be described.

  17. 2nd Sandia Fracture Challenge Summit: Sandia California's Modeling Approach

    Energy Technology Data Exchange (ETDEWEB)

    Karlson, Kyle N. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Brown, Arthur [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Foulk, James W. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2015-02-01

    Team Sandia California (Team H) used the Sandia code SIERRA Solid Mechanics: Implicit (SIERRA SM) to model the SFC2 challenge problem. SIERRA SM is a Lagrangian, three-dimensional, implicit code for the analysis of solids and structures. It contains a versatile library of continuum and structural elements, and an extensive library of material models. For all SFC2 related simulations, our team used Q1P0, 8 node hexahedral elements with element side lengths on the order 0.175 mm in failure regions. To model crack initiation and failure, element death removed elements from the simulation according to a continuum damage model. SIERRA SM’s implicit dynamics, implemented with an HHT time integration scheme for numerical damping [1], was used to model the unstable failure modes of the models. We chose SIERRA SM’s isotropic Elasto Viscoplastic material model for our simulations because it contains most of the physics required to accurately model the SFC2 challenge problem such as the flexibility to include temperature and rate dependence for a material.

  18. Carbon nanotubes for thermal interface materials in microelectronic packaging

    Science.gov (United States)

    Lin, Wei

    As the integration scale of transistors/devices in a chip/system keeps increasing, effective cooling has become more and more important in microelectronics. To address the thermal dissipation issue, one important solution is to develop thermal interface materials with higher performance. Carbon nanotubes, given their high intrinsic thermal and mechanical properties, and their high thermal and chemical stabilities, have received extensive attention from both academia and industry as a candidate for high-performance thermal interface materials. The thesis is devoted to addressing some challenges related to the potential application of carbon nanotubes as thermal interface materials in microelectronics. These challenges include: 1) controlled synthesis of vertically aligned carbon nanotubes on various bulk substrates via chemical vapor deposition and the fundamental understanding involved; 2) development of a scalable annealing process to improve the intrinsic properties of synthesized carbon nanotubes; 3) development of a state-of-art assembling process to effectively implement high-quality vertically aligned carbon nanotubes into a flip-chip assembly; 4) a reliable thermal measurement of intrinsic thermal transport property of vertically aligned carbon nanotube films; 5) improvement of interfacial thermal transport between carbon nanotubes and other materials. The major achievements are summarized. 1. Based on the fundamental understanding of catalytic chemical vapor deposition processes and the growth mechanism of carbon nanotube, fast synthesis of high-quality vertically aligned carbon nanotubes on various bulk substrates (e.g., copper, quartz, silicon, aluminum oxide, etc.) has been successfully achieved. The synthesis of vertically aligned carbon nanotubes on the bulk copper substrate by the thermal chemical vapor deposition process has set a world record. In order to functionalize the synthesized carbon nanotubes while maintaining their good vertical alignment

  19. Experiences with integral microelectronics on smart structures for space

    Science.gov (United States)

    Nye, Ted; Casteel, Scott; Navarro, Sergio A.; Kraml, Bob

    1995-05-01

    One feature of a smart structure implies that some computational and signal processing capability can be performed at a local level, perhaps integral to the controlled structure. This requires electronics with a minimal mechanical influence regarding structural stiffening, heat dissipation, weight, and electrical interface connectivity. The Advanced Controls Technology Experiment II (ACTEX II) space-flight experiments implemented such a local control electronics scheme by utilizing composite smart members with integral processing electronics. These microelectronics, tested to MIL-STD-883B levels, were fabricated with conventional thick film on ceramic multichip module techniques. Kovar housings and aluminum-kapton multilayer insulation was used to protect against harsh space radiation and thermal environments. Development and acceptance testing showed the electronics design was extremely robust, operating in vacuum and at temperature range with minimal gain variations occurring just above room temperatures. Four electronics modules, used for the flight hardware configuration, were connected by a RS-485 2 Mbit per second serial data bus. The data bus was controlled by Actel field programmable gate arrays arranged in a single master, four slave configuration. An Intel 80C196KD microprocessor was chosen as the digital compensator in each controller. It was used to apply a series of selectable biquad filters, implemented via Delta Transforms. Instability in any compensator was expected to appear as large amplitude oscillations in the deployed structure. Thus, over-vibration detection circuitry with automatic output isolation was incorporated into the design. This was not used however, since during experiment integration and test, intentionally induced compensator instabilities resulted in benign mechanical oscillation symptoms. Not too surprisingly, it was determined that instabilities were most detectable by large temperature increases in the electronics, typically

  20. Joint Sandia/NIOSH exercise on aerosol contamination using the BROOM tool.

    Energy Technology Data Exchange (ETDEWEB)

    Ramsey, James L., Jr. (.,; .); Melton, Brad; Finley, Patrick; Brockman, John; Peyton, Chad E.; Tucker, Mark David; Einfeld, Wayne; Brown, Gary Stephen; Griffith, Richard O.; Lucero, Daniel A.; Knowlton, Robert G.; McKenna, Sean Andrew; Ho, Pauline

    2006-06-01

    In February of 2005, a joint exercise involving Sandia National Laboratories (SNL) and the National Institute for Occupational Safety and Health (NIOSH) was conducted in Albuquerque, NM. The SNL participants included the team developing the Building Restoration Operations and Optimization Model (BROOM), a software product developed to expedite sampling and data management activities applicable to facility restoration following a biological contamination event. Integrated data-collection, data-management, and visualization software improve the efficiency of cleanup, minimize facility downtime, and provide a transparent basis for reopening. The exercise was held at an SNL facility, the Coronado Club, a now-closed social club for Sandia employees located on Kirtland Air Force Base. Both NIOSH and SNL had specific objectives for the exercise, and all objectives were met.

  1. Solar energy research at Sandia Laboratories and its effects on health and safety

    Energy Technology Data Exchange (ETDEWEB)

    Young, L.L. III

    1977-10-01

    Various solar energy research and development projects at Sandia Laboratories are discussed with emphasis on the primary health and safety hazard associated with solar concentration systems. This limiting hazard is chorioretinal damage. The unique safety and health hazards associated with solar energy collector and receiver systems cannot be measured yet, but progress is being made rapidly. Research is continuing, especially for eye hazards, with more extensive work planned.

  2. Sandia's mentoring program : an ongoing success.

    Energy Technology Data Exchange (ETDEWEB)

    Brewer, Soila

    2003-12-01

    This report summarizes the Mentoring Program at Sandia National Laboratories (SNL), which has been an on-going success since its inception in 1995. The Mentoring Program provides a mechanism to develop a workforce able to respond to changing requirements and complex customer needs. The program objectives are to enhance employee contributions through increased knowledge of SNL culture, strategies, and programmatic direction. Mentoring is a proven mechanism for attracting new employees, retaining employees, and developing leadership. It helps to prevent the loss of corporate knowledge from attrition and retirement, and it increases the rate and level of contributions of new managers and employees, also spurring cross-organizational teaming. The Mentoring Program is structured as a one-year partnership between an experienced staff member or leader and a less experienced one. Mentors and mentees are paired according to mutual objectives and interests. Support is provided to the matched pairs from their management as well as division program coordinators in both New Mexico and California locations. In addition, bi-monthly large-group training sessions are held.

  3. Simulation information regarding Sandia National Laboratories trinity capability improvement metric.

    Energy Technology Data Exchange (ETDEWEB)

    Agelastos, Anthony Michael; Lin, Paul T.

    2013-10-01

    Sandia National Laboratories, Los Alamos National Laboratory, and Lawrence Livermore National Laboratory each selected a representative simulation code to be used as a performance benchmark for the Trinity Capability Improvement Metric. Sandia selected SIERRA Low Mach Module: Nalu, which is a uid dynamics code that solves many variable-density, acoustically incompressible problems of interest spanning from laminar to turbulent ow regimes, since it is fairly representative of implicit codes that have been developed under ASC. The simulations for this metric were performed on the Cielo Cray XE6 platform during dedicated application time and the chosen case utilized 131,072 Cielo cores to perform a canonical turbulent open jet simulation within an approximately 9-billion-elementunstructured- hexahedral computational mesh. This report will document some of the results from these simulations as well as provide instructions to perform these simulations for comparison.

  4. Description of heat flux measurement methods used in hydrocarbon and propellant fuel fires at Sandia.

    Energy Technology Data Exchange (ETDEWEB)

    Nakos, James Thomas

    2010-12-01

    The purpose of this report is to describe the methods commonly used to measure heat flux in fire applications at Sandia National Laboratories in both hydrocarbon (JP-8 jet fuel, diesel fuel, etc.) and propellant fires. Because these environments are very severe, many commercially available heat flux gauges do not survive the test, so alternative methods had to be developed. Specially built sensors include 'calorimeters' that use a temperature measurement to infer heat flux by use of a model (heat balance on the sensing surface) or by using an inverse heat conduction method. These specialty-built sensors are made rugged so they will survive the environment, so are not optimally designed for ease of use or accuracy. Other methods include radiometers, co-axial thermocouples, directional flame thermometers (DFTs), Sandia 'heat flux gauges', transpiration radiometers, and transverse Seebeck coefficient heat flux gauges. Typical applications are described and pros and cons of each method are listed.

  5. A user`s guide to SABLE 2.0: The Sandia Automated Boolean Logic Evaluation software

    Energy Technology Data Exchange (ETDEWEB)

    Hays, K.M.; Wyss, G.D.; Daniel, S.L. [Sandia National Labs., Albuquerque, NM (United States). Risk Assessment and Systems Modeling Dept.

    1996-04-01

    This document is a reference guide for the Sandia Automated Boolean Logic Evaluation software (SABLE) version 2.0 developed at Sandia National Laboratories. SABLE 2.0 is designed to solve and quantify fault trees on IBM-compatible personal computers using the Microsoft Windows operating environment. SABLE 2.0 consists of a Windows user interface combined with a fault tree solution engine that is derived from the well-known SETS fault tree analysis code. This manual explains the fundamentals of solving fault trees and shows how to use the Windows SABLE 2.0 interface to specify a problem, solve the problem, and view the output.

  6. Job stress models, depressive disorders and work performance of engineers in microelectronics industry.

    Science.gov (United States)

    Chen, Sung-Wei; Wang, Po-Chuan; Hsin, Ping-Lung; Oates, Anthony; Sun, I-Wen; Liu, Shen-Ing

    2011-01-01

    Microelectronic engineers are considered valuable human capital contributing significantly toward economic development, but they may encounter stressful work conditions in the context of a globalized industry. The study aims at identifying risk factors of depressive disorders primarily based on job stress models, the Demand-Control-Support and Effort-Reward Imbalance models, and at evaluating whether depressive disorders impair work performance in microelectronics engineers in Taiwan. The case-control study was conducted among 678 microelectronics engineers, 452 controls and 226 cases with depressive disorders which were defined by a score 17 or more on the Beck Depression Inventory and a psychiatrist's diagnosis. The self-administered questionnaires included the Job Content Questionnaire, Effort-Reward Imbalance Questionnaire, demography, psychosocial factors, health behaviors and work performance. Hierarchical logistic regression was applied to identify risk factors of depressive disorders. Multivariate linear regressions were used to determine factors affecting work performance. By hierarchical logistic regression, risk factors of depressive disorders are high demands, low work social support, high effort/reward ratio and low frequency of physical exercise. Combining the two job stress models may have better predictive power for depressive disorders than adopting either model alone. Three multivariate linear regressions provide similar results indicating that depressive disorders are associated with impaired work performance in terms of absence, role limitation and social functioning limitation. The results may provide insight into the applicability of job stress models in a globalized high-tech industry considerably focused in non-Western countries, and the design of workplace preventive strategies for depressive disorders in Asian electronics engineering population.

  7. A four-channel microelectronic system for neural signal regeneration

    Energy Technology Data Exchange (ETDEWEB)

    Xie Shushan; Wang Zhigong; Li Wenyuan [Institute of RF- and OE-ICs, Southeast University, Nanjing 210096 (China); Lue Xiaoying; Pan Haixian, E-mail: zgwang@seu.edu.c [State Key Laboratory of Bio-Electronics, Southeast University, Nanjing 210096 (China)

    2009-12-15

    This paper presents a microelectronic system which is capable of making a signal record and functional electric stimulation of an injured spinal cord. As a requirement of implantable engineering for the regeneration microelectronic system, the system is of low noise, low power, small size and high performance. A front-end circuit and two high performance OPAs (operational amplifiers) have been designed for the system with different functions, and the two OPAs are a low-noise low-power two-stage OPA and a constant-g{sub m} RTR input and output OPA. The system has been realized in CSMC 0.5-{mu}m CMOS technology. The test results show that the system satisfies the demands of neuron signal regeneration. (semiconductor integrated circuits)

  8. Applicability of LET to single events in microelectronic structures

    Science.gov (United States)

    Xapsos, Michael A.

    1992-12-01

    LET is often used as a single parameter to determine the energy deposited in a microelectronic structure by a single event. The accuracy of this assumption is examined for ranges of ion energies and volumes of silicon appropriate for modern microelectronics. It is shown to be accurate only under very restricted conditions. Significant differences arise because (1) LET is related to energy lost by the ion, not energy deposited in the volume; and (2) LET is an average value and does not account for statistical variations in energy deposition. Criteria are suggested for determining when factors other than LET should be considered, and new analytical approaches are presented to account for them. One implication of these results is that improvements can be made in space upset rate predictions by incorporating the new methods into currently used codes such as CREME and CRUP.

  9. A four-channel microelectronic system for neural signal regeneration

    Institute of Scientific and Technical Information of China (English)

    Xie Shushan; Wang Zhigong; Lü Xiaoying; Li Wenyuan; Pan Haixian

    2009-01-01

    This paper presents a microelectronic system which is capable of making a signal record and functional electric stimulation of an injured spinal cord. As a requirement of implantable engineering for the regeneration microelectronic system, the system is of low noise, low power, small size and high performance. A front-end circuit and two high performance OPAs (operational amplifiers) have been designed for the system with different functions,and the two OPAs are a low-noise low-power two-stage OPA and a constant-g_m RTR input and output OPA. The system has been realized in CSMC 0.5-μm CMOS technology. The test results show that the system satisfies the demands of neuron signal regeneration.

  10. Microvibration monitoring: some recent experiences in an operating microelectronics facility

    Science.gov (United States)

    Hassett, Kevin

    1992-02-01

    Major construction work is currently underway at Intel''s Aloha, Oregon, campus. Because of concerns about the effects that construction-generated vibration might have on adjacent ongoing microelectronics manufacturing activities, two important steps were taken. The first of these was to establish guidelines that would be followed by the construction contractor to limit vibration disturbance. The second was to install a computer-based monitoring system that would continuously measure the vibration on the floor of the microelectronics manufacturing facility. In this way, the vibration effects of the construction activities would be monitored and adjusted, by modifying procedures, if necessary. The monitoring program is discussed in this paper. The major characteristics of the monitoring system, the placement of the transducers, and the ways in which the data were managed are described. Some typical data are shown and discussed.

  11. 1996 Site environmental report Sandia National Laboratories Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Fink, C.H. [ed.] [Sandia National Labs., Albuquerque, NM (United States); Duncan, D. [ed.] [GRAM, Inc., Albuquerque, NM (United States); Sanchez, R. [Jobs Plus, Albuquerque, NM (United States)

    1997-08-01

    Sandia National Laboratories/New Mexico (SNL/NM) is operated in support of the U.S. Department of Energy (DOE) mission to provide weapon component technology and hardware for national security needs, and to conduct fundamental research and development (R&D) to advance technology in energy research, computer science, waste management, electronics, materials science, and transportation safety for hazardous and nuclear components. In support of this mission, the Environmental Safety and Health (ES&H) Center at SNL/NM conducts extensive environmental monitoring, surveillance, and compliance activities to assist SNL`s line organizations in meeting all applicable environmental regulations applicable to the site including those regulating radiological and nonradiological effluents and emissions. Also herein are included, the status of environmental programs that direct and manage activities such as terrestrial surveillance; ambient air and meteorological monitoring; hazardous, radioactive, and solid waste management; pollution prevention and waste minimization; environmental restoration (ER); oil and chemical spill prevention; and National Environmental Policy Act (NEPA) documentation. This report has been prepared in compliance with DOE order 5400.1, General Environmental Protection.

  12. Chunk projectile launch using the Sandia Hypervelocity Launcher Facility

    Energy Technology Data Exchange (ETDEWEB)

    Chhabildas, L.C.; Trucano, T.G.; Reinhart, W.D.; Hall, C.A.

    1994-07-01

    An experimental technique is described to launch an intact ``chunk,`` i.e. a 0.3 cm thick by 0.6 cm diameter cylindrical titanium alloy (Ti-6Al-4V) flyer, to 10.2 km/s. The ability to launch fragments having such an aspect ratio is important for hypervelocity impact phenomenology studies. The experimental techniques used to accomplish this launch were similar but not identical to techniques developed for the Sandia HyperVelocity Launcher (HVL). A confined barrel impact is crucial in preventing the two-dimensional effects from dominating the loading response of the projectile chunk. The length to diameter ratio of the metallic chunk that is launched to 10.2 km/s is 0.5 and is an order of magnitude larger than those accomplished using the conventional hypervelocity launcher. The multi-dimensional, finite-difference (finite-volume), hydrodynamic code CTH was used to evaluate and assess the acceleration characteristics i.e., the in-bore ballistics of the chunky projectile launch. A critical analysis of the CTH calculational results led to the final design and the experimental conditions that were used in this study. However, the predicted velocity of the projectile chunk based on CTH calculations was {approximately} 6% lower than the measured velocity of {approximately}10.2 km/S.

  13. Radiofrequency and microwave radiation in the microelectronics industry.

    Science.gov (United States)

    Cohen, R

    1986-01-01

    The microscopic precision required to produce minute integrated circuits is dependent on several processes utilizing radiofrequency and microwave radiation. This article provides a review of radiofrequency and microwave exposures in microelectronics and of the physical and biologic properties of these types of radiation; summarizes the existing, relevant medical literature; and provides the clinician with guidelines for diagnosis and treatment of excessive exposures to microwave and radiofrequency radiation.

  14. Microelectronics Revolution And The Impact Of Automation In The New Industrialized Countries

    Science.gov (United States)

    Baranauskas, Vitor

    1984-08-01

    A brief review of some important historical points on the origin of the Factories and the Industrial Revolution is presented with emphasis in the social problems related to the automation of the human labor. Until the World War I, the social changes provoked by the Industrial Revolution caused one division of the World in developed and underdeveloped countries. After that period, the less developed nations began their industrialization mainly through the Multinationals Corporations (MC). These enterprises were very important to the production and exportation of utilities and manufactures in general, mainly in those products which required intensive and direct human labor. At present time, with the pervasiveness of microelectronics in the automation, this age seems to reaching an end because all continous processes in industry tend economicaly toward total automation. This fact will cause a retraction in long-term investments and, beyond massive unemployment, there is a tendency for these MC industries to return to their original countries. The most promising alternative to avoid these events, and perhaps the unique, is to incentive an autonomous development in areas of high technology, as for instance, the microelectronics itself.

  15. Implications of Pb-free microelectronics assembly in aerospace applications

    Science.gov (United States)

    Shapiro, A. A.; Bonner, J. K.; Ogunseitan, D.; Saphores, J. D.; Schoenung, J.

    2003-01-01

    The commercial microelectronics industry is rapidly moving to completely Pb-free assembly strategies within the next decade. This trend is being driven by existing and proposed legislation in Europe and in Japan. The microelectronics industry has become truly global, as indicated by major U .S. firms who already adopted Pb-free implementation programs. Among these forward-looking firms are AT&T, IBM, Motorola, HP and Intel to name a few.Following Moore's law, advances in microelectronics are happening very rapidly. In many cases, commercial industry is ahead of the aerospace sector in technology. Progress by commercial industry, along with cost, drives the use of Commercial Off-The-Shelf (COTS) parts for military and space applications. We can thus anticipate that the aerospace industry will, at some point, be forced to use Pb-free components and subsystems as part of their standard business practices. In this paper we attempt to provide a snapshot of the commercial industry trends and how they may impact electronics in the aerospace environment. In addition, we also look at different strategies for implementation. Finally we present data collected on a recent NASA project to focus on finding suitable alternatives to eutectic tin-lead solders and solder pastes. The world is moving toward implementation of environmentally friendly manufacturing techniques. The aerospace industry will be forced to deal with issues related with Pb free assembly, either by availability or legislation. This paper provides some insight into some of the tradeoffs that should be considered.

  16. 1993 Site environmental report Sandia National Laboratories, Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Culp, T.A.; Cheng, C.F.; Cox, W.; Durand, N.; Irwin, M.; Jones, A.; Lauffer, F.; Lincoln, M.; McClellan, Y.; Molley, K. [and others

    1994-11-01

    This 1993 report contains monitoring data from routine radiological and nonradiological environmental surveillance activities. Summaries of significant environmental compliance programs in progress, such as National Environmental Policy Act documentation, environmental permits, environmental restoration, and various waste management programs for Sandia National Laboratories in Albuquerque, New Mexico, are included. The maximum offsite dose impact was calculated to be 0.0016 millirem. The total population within a 50-mile (80 kilometer) radius of Sandia National Laboratories/New Mexico received an estimated collective dose of 0.027 person-rem during 1993 from the laboratories operations, As in the previous year, the 1993 operations at Sandia National Laboratories/New Mexico had no discernible impact on the general public or on the environment. This report is prepared for the U.S. Department of Energy in compliance with DOE Order 5400.1.

  17. 1992 Environmental monitoring report, Sandia National Laboratories, Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Culp, T.; Cox, W.; Hwang, H.; Irwin, M.; Jones, A.; Matz, B.; Molley, K.; Rhodes, W.; Stermer, D.; Wolff, T.

    1993-09-01

    This 1992 report contains monitoring data from routine radiological and nonradiological environmental surveillance activities. summaries of significant environmental compliance programs in progress, such as National Environmental Policy Act documentation, environmental permits, envirorunental restoration, and various waste management programs for Sandia National Laboratories in Albuquerque, New Mexico, are included. The maximum offsite dose impact was calculated to be 0.0034 millirem. The total population within a 50-mile radius of Sandia National Laboratories/New Mexico received an estimated collective dose of 0.019 person-rem during 1992 from the laboratories` operations. As in the previous year, the 1992 operations at Sandia National Laboratories/New Mexico had no discernible impact on the general public or on the environment.

  18. Nuclear energy related capabilities at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Pickering, Susan Y. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-02-01

    Sandia National Laboratories' technology solutions are depended on to solve national and global threats to peace and freedom. Through science and technology, people, infrastructure, and partnerships, part of Sandia's mission is to meet the national needs in the areas of energy, climate and infrastructure security. Within this mission to ensure clean, abundant, and affordable energy and water is the Nuclear Energy and Fuel Cycle Programs. The Nuclear Energy and Fuel Cycle Programs have a broad range of capabilities, with both physical facilities and intellectual expertise. These resources are brought to bear upon the key scientific and engineering challenges facing the nation and can be made available to address the research needs of others. Sandia can support the safe, secure, reliable, and sustainable use of nuclear power worldwide by incorporating state-of-the-art technologies in safety, security, nonproliferation, transportation, modeling, repository science, and system demonstrations.

  19. Displacement Damage Effects in Solar Cells: Mining Damage From the Microelectronics and Photonics Test Bed Space Experiment

    Science.gov (United States)

    Hardage, Donna (Technical Monitor); Walters, R. J.; Morton, T. L.; Messenger, S. R.

    2004-01-01

    The objective is to develop an improved space solar cell radiation response analysis capability and to produce a computer modeling tool which implements the analysis. This was accomplished through analysis of solar cell flight data taken on the Microelectronics and Photonics Test Bed experiment. This effort specifically addresses issues related to rapid technological change in the area of solar cells for space applications in order to enhance system performance, decrease risk, and reduce cost for future missions.

  20. Aquatic macroinvertebrates and water quality of Sandia Canyon, Los Alamos National Laboratory, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Cross, S.; Nottelman, H.

    1997-01-01

    The Biology Team of ESH-20 (the Ecology Group) at Los Alamos National Laboratory (LANL) has collected samples from the stream within Sandia Canyon since the summer of 1990. These field studies measure water quality parameters and collect aquatic macroinvertebrates from sampling sites within the upper canyon stream. Reports by Bennett and Cross discuss previous aquatic studies in Sandia Canyon. This report updates and expands the previous findings. The Biology Team collected water quality data and aquatic macroinvertebrates monthly at three sampling stations within Sandia Canyon in 1995. The two upstream stations occur near a cattail (Typha latifolia) dominated marsh downstream from outfalls that discharge industrial and sanitary waste effluent into the stream, thereby maintaining year-round flow. The third station is approximately 1.5 miles downstream from the outfalls within a mixed conifer forest. All water chemistry parameters measured in Sandia Canyon during 1995 fell within acceptable State limits and scored in the {open_quotes}good{close_quotes} or {open_quotes}excellent{close_quotes} ranges when compared to an Environmental Quality Index. However, aquatic macroinvertebrates habitats have been degraded by widespread erosion, channelization, loss of wetlands due to deposition and stream lowering, scour, limited acceptable substrates, LANL releases and spills, and other stressors. Macroinvertebrate communities at all the stations had low diversities, low densities, and erratic numbers of individuals. These results indicate that although the stream possesses acceptable water chemistry, it has reduced biotic potential. The best developed aquatic community occurs at the sampling station with the best habitat and whose downstream location partially mitigates the effects of upstream impairments.

  1. The high current, fast, 100ns, Linear Transformer Driver (LTD) developmental project at Sandia National Laboratories.

    Energy Technology Data Exchange (ETDEWEB)

    Ward, Kevin S.; Long, Finis W.; Sinebryukhov, Vadim A. (High Current Electronic Institute (HCEI), Tomsk, Russia); Kim, Alexandre A. (High Current Electronic Institute (HCEI), Tomsk, RUSSIA); Wakeland, Peter Eric (Ktech Corporation, Albuquerque, NM); McKee, G. Randall; Woodworth, Joseph Ray; McDaniel, Dillon Heirman; Fowler, William E.; Mazarakis, Michael Gerrassimos; Porter, John Larry, Jr.; Struve, Kenneth William; Stygar, William A.; LeChien, Keith R.; Matzen, Maurice Keith

    2010-04-01

    Sandia National Laboratories, Albuquerque, N.M., USA, in collaboration with the High Current Electronic Institute (HCEI), Tomsk, Russia, is developing a new paradigm in pulsed power technology: the Linear Transformer Driver (LTD) technology. This technological approach can provide very compact devices that can deliver very fast high current and high voltage pulses straight out of the cavity with out any complicated pulse forming and pulse compression network. Through multistage inductively insulated voltage adders, the output pulse, increased in voltage amplitude, can be applied directly to the load. The load may be a vacuum electron diode, a z-pinch wire array, a gas puff, a liner, an isentropic compression load (ICE) to study material behavior under very high magnetic fields, or a fusion energy (IFE) target. This is because the output pulse rise time and width can be easily tailored to the specific application needs. In this paper we briefly summarize the developmental work done in Sandia and HCEI during the last few years, and describe our new MYKONOS Sandia High Current LTD Laboratory.

  2. Moore's law and the impact on trusted and radiation-hardened microelectronics.

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Kwok Kee

    2011-12-01

    In 1965 Gordon Moore wrote an article claiming that integrated circuit density would scale exponentially. His prediction has remained valid for more than four decades. Integrated circuits have changed all aspects of everyday life. They are also the 'heart and soul' of modern systems for defense, national infrastructure, and intelligence applications. The United States government needs an assured and trusted microelectronics supply for military systems. However, migration of microelectronics design and manufacturing from the United States to other countries in recent years has placed the supply of trusted microelectronics in jeopardy. Prevailing wisdom dictates that it is necessary to use microelectronics fabricated in a state-of-the-art technology for highest performance and military system superiority. Close examination of silicon microelectronics technology evolution and Moore's Law reveals that this prevailing wisdom is not necessarily true. This presents the US government the possibility of a totally new approach to acquire trusted microelectronics.

  3. Wireless Integrated Microelectronic Vacuum Sensor System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The efficient utilization of ground test facilities and launch sites is critical for the success of NASA's New Vision for Space Exploration. The development of an...

  4. Wireless Integrated Microelectronic Vacuum Sensor System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The efficient utilization of ground test facilities and launch sites is critical for the success of NASA's New Vision for Space Exploration. The development of an...

  5. Military applications for heterostructure microelectronics technology

    Science.gov (United States)

    Greiling, Paul; Kirkpatrick, Conilee; Valentine, Gary

    1995-09-01

    Military systems, whether radar, communications, electronic warfare (EW) or smart munitions, require superior device and IC performance. The performance advantages of heterostructure devices over standard Si CMOS, Si bipolar transistors or GaAs MESFETs has motivated major aerospace firms in the United States to develop Si, GaAs and InP-based heterojunction bipolar (HBT) and high electron mobility transistor (HEMT) technologies. In response to advanced system performance requirements, technology efforts are being pushed toward devices which can yield {T}/{R} modules with octave bandwidths, noise figures under 3 dB, output power of 20 W and power greater than 30%. Device technology development for satellite communications is being driven in part by the need for ultra low noise high output power with high power added efficiency with high MMTF. For these systems as well as EW applications, designers want to digitize the signal as close to the front end as possible. This is driving the development of a 100 GHz IC technology for A/D converters, synthesizers, MUX/DEMUXs, DDSs. and PRNs. Requirements for A/D converters with 16 bits @ 100-200 MHz up to 8-10 bits @ 10 GHz are appearing for advanced radars and EW systems. The military system requirements continue to drive the development of the newer, better and higher performance heterostructure device technologies.

  6. Sandia bicycle commuters group -- pollution prevention at Sandia National Laboratories, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Wrons, R.

    1998-06-01

    The Sandia Bicycle Commuters Group (SBCG) formed three years ago for the purpose of addressing issues that impact the bicycle commuting option. The meeting that launched the SBCG was scheduled in conjunction with National Bike-to-Work day in May 1995. Results from a survey handed out at the meeting solidly confirmed the issues and that an advocacy group was needed. The purpose statement for the Group headlines its web site and brochure: ``Existing to assist and educate the SNL workforce bicyclist on issues regarding Kirtland Air Force Base (KAFB) access, safety and bicycle-supporting facilities, in order to promote bicycling as an effective and enjoyable means of commuting.`` The SNL Pollution Prevention (P2) Team`s challenge to the SNL workforce is to ``prevent pollution, conserve natural resources, and save money``. In the first winter of its existence, the SBCG sponsored a winter commute contest in conjunction with the City`s Clean Air Campaign (CAC). The intent of the CAC is to promote alternative (to the single-occupant vehicle) commuting during the Winter Pollution Advisory Period (October 1--February 28), when the City runs the greatest risk of exceeding federal pollution limits.

  7. Sandia bicycle commuters group -- pollution prevention at Sandia National Laboratories, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Wrons, R.

    1998-06-01

    The Sandia Bicycle Commuters Group (SBCG) formed three years ago for the purpose of addressing issues that impact the bicycle commuting option. The meeting that launched the SBCG was scheduled in conjunction with National Bike-to-Work day in May 1995. Results from a survey handed out at the meeting solidly confirmed the issues and that an advocacy group was needed. The purpose statement for the Group headlines its web site and brochure: ``Existing to assist and educate the SNL workforce bicyclist on issues regarding Kirtland Air Force Base (KAFB) access, safety and bicycle-supporting facilities, in order to promote bicycling as an effective and enjoyable means of commuting.`` The SNL Pollution Prevention (P2) Team`s challenge to the SNL workforce is to ``prevent pollution, conserve natural resources, and save money``. In the first winter of its existence, the SBCG sponsored a winter commute contest in conjunction with the City`s Clean Air Campaign (CAC). The intent of the CAC is to promote alternative (to the single-occupant vehicle) commuting during the Winter Pollution Advisory Period (October 1--February 28), when the City runs the greatest risk of exceeding federal pollution limits.

  8. Advanced robotic technologies for transfer at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Bennett, P.C.

    1994-10-01

    Hazardous operations which have in the past been completed by technicians are under increased scrutiny due to high costs and low productivity associated with providing protective clothing and environments. As a result, remote systems are needed to accomplish many hazardous materials handling tasks such as the clean-up of waste sites in which the exposure of personnel to radiation, chemical, explosive and other hazardous constituents is unacceptable. Computer models augmented by sensing, and structured, modular computing environments are proving effective in automating many unstructured hazardous tasks. Work at Sandia National Laboratories (SNL) has focused on applying flexible automation (robotics) to meet the needs of the U.S. Department of Energy (USDOE). Dismantling facilities, environmental remediation, and materials handling in changing, hazardous environments lead to many technical challenges. Computer planning, monitoring and operator assistance shorten training cycles, reduce errors, and speed execution of operations. Robotic systems that re-use well-understood generic technologies can be much better characterized than robotic systems developed for a particular application, leading to a more reliable and safer systems. Further safety in robotic operations results from use of environmental sensors and knowledge of the task and environment. Collision detection and avoidance is achieved from such sensor integration and model-based control. This paper discusses selected technologies developed at SNL for use within the USDOE complex that have been or are ready for transfer to government and industrial suppliers. These technologies include sensors, sub-systems, and the design philosophy applied to quickly integrate them into a working robotic system. This paper represents the work of many people at the Intelligent Systems and Robotics Center at SNL, to whom the credit belongs.

  9. Energy Systems Integration Partnerships: NREL + Sandia + Johnson Controls

    Energy Technology Data Exchange (ETDEWEB)

    2017-04-05

    NREL and Sandia National Laboratories partnered with Johnson Controls to deploy the company's BlueStream Hybrid Cooling System at ESIF's high-performance computing data center to reduce water consumption seen in evaporative cooling towers.

  10. 1995 Site environmental report Sandia National Laboratories, Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Shyr, L.J.; Duncan, D. [eds.; Sanchez, R.

    1996-09-01

    This 1995 report contains data from routine radiological and non-radiological environmental monitoring activities. Summaries of significant environmental compliance programs in progress, such as National Environmental Policy Act documentation, environmental permits, environmental restoration and various waste management programs at Sandia National Laboratories in Albuquerque, New Mexico, are included.

  11. Site environmental report for 2009 : Sandia National Laboratories, California.

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L.

    2010-06-01

    Sandia National Laboratories, California (SNL/CA) is a government-owned/contractor-operated laboratory. Sandia Corporation, a Lockheed Martin Company, operates the laboratory for the Department of Energy's National Nuclear Security Administration (NNSA). The NNSA Sandia Site Office oversees operations at the site, using Sandia Corporation as a management and operating contractor. This Site Environmental Report for 2009 was prepared in accordance with DOE Order 231.1A (DOE 2004a). The report provides a summary of environmental monitoring information and compliance activities that occurred at SNL/CA during calendar year 2009. General site and environmental program information is also included. The Site Environmental Report is divided into ten chapters. Chapter 1, the Executive Summary, highlights compliance and monitoring results obtained in 2009. Chapter 2 provides a brief introduction to SNL/CA and the existing environment found on site. Chapter 3 summarizes SNL/CA's compliance activities with the major environmental requirements applicable to site operations. Chapter 4 presents information on environmental management, performance measures, and environmental programs. Chapter 5 presents the results of monitoring and surveillance activities in 2009. Chapter 6 discusses quality assurance. Chapters 7 through 9 provide supporting information for the report and Chapter 10 is the report distribution list.

  12. Evaluation of Strontium Selectivity by Sandia Octahedral Molecular Sieves (SOMS).

    Energy Technology Data Exchange (ETDEWEB)

    Rigali, Mark J.; Stewart, Thomas Austin

    2016-01-01

    Sandia National Laboratories has collaborated with Pleasanton Ridge Research Company (PRRC) to determine whether Sandia Octahedral Molecular Sieves (SOMS) and modified SOMs materials can be synthesized in large batches and produced in granular form. Sandia National Laboratories tested these SOMS and its variants based in aqueous chemical environments for an application-based evaluation of material performance as a sorbent. Testing focused primarily on determining the distribution coefficients (K d ) and chemical selectivity SOMs for alkali earth (Sr) ions in aqueous and dilute seawater solutions. In general the well-crystallized SOMS materials tested exhibited very high K d values (>10 6 ) in distilled water but K d values dropped substantially (%7E10 2 -10 3 ) in the dilute seawater (3%). However, one set of SOMS samples (1.4.2 and 1.4.6) provided by PRRC yielded relatively high K d (approaching 10 4 ) in dilute seawater. Further examination of these samples by scanning electron microscopy (SEM) revealed the presence of at least two phases at least one of which may be accounting for the improved K d values in dilute seawater. Evaluation of Strontium Selectivity by Sandia Octahedral Molecular Sieves (SOMS) January 20, 2016

  13. Power source evaluation capabilities at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Doughty, D.H.; Butler, P.C.

    1996-04-01

    Sandia National Laboratories maintains one of the most comprehensive power source characterization facilities in the U.S. National Laboratory system. This paper describes the capabilities for evaluation of fuel cell technologies. The facility has a rechargeable battery test laboratory and a test area for performing nondestructive and functional computer-controlled testing of cells and batteries.

  14. Sandia National Laboratories, California Environmental Management System program manual

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L.

    2014-04-01

    The Sandia National Laboratories, California (SNL/CA) Environmental Management System (EMS) Program Manual documents the elements of the site EMS Program. The SNL/CA EMS Program conforms to the International Standard on Environmental Management Systems, ISO 14001:2004 and Department of Energy (DOE) Order 436.1.

  15. Sandia National Laboratories, California Environmental Management System program manual.

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L.

    2013-04-01

    The Sandia National Laboratories, California (SNL/CA) Environmental Management System (EMS) Program Manual documents the elements of the site EMS Program. The SNL/CA EMS Program conforms to the International Standard on Environmental Management Systems, ISO 14001:2004 and Department of Energy (DOE) Order 436.1.

  16. Optimization of Microelectronic Devices for Sensor Applications

    Science.gov (United States)

    Cwik, Tom; Klimeck, Gerhard

    2000-01-01

    The NASA/JPL goal to reduce payload in future space missions while increasing mission capability demands miniaturization of active and passive sensors, analytical instruments and communication systems among others. Currently, typical system requirements include the detection of particular spectral lines, associated data processing, and communication of the acquired data to other systems. Advances in lithography and deposition methods result in more advanced devices for space application, while the sub-micron resolution currently available opens a vast design space. Though an experimental exploration of this widening design space-searching for optimized performance by repeated fabrication efforts-is unfeasible, it does motivate the development of reliable software design tools. These tools necessitate models based on fundamental physics and mathematics of the device to accurately model effects such as diffraction and scattering in opto-electronic devices, or bandstructure and scattering in heterostructure devices. The software tools must have convenient turn-around times and interfaces that allow effective usage. The first issue is addressed by the application of high-performance computers and the second by the development of graphical user interfaces driven by properly developed data structures. These tools can then be integrated into an optimization environment, and with the available memory capacity and computational speed of high performance parallel platforms, simulation of optimized components can proceed. In this paper, specific applications of the electromagnetic modeling of infrared filtering, as well as heterostructure device design will be presented using genetic algorithm global optimization methods.

  17. PREFACE: E-MRS 2012 Spring Meeting, Symposium M: More than Moore: Novel materials approaches for functionalized Silicon based Microelectronics

    Science.gov (United States)

    Wenger, Christian; Fompeyrine, Jean; Vallée, Christophe; Locquet, Jean-Pierre

    2012-12-01

    More than Moore explores a new area of Silicon based microelectronics, which reaches beyond the boundaries of conventional semiconductor applications. Creating new functionality to semiconductor circuits, More than Moore focuses on motivating new technological possibilities. In the past decades, the main stream of microelectronics progresses was mainly powered by Moore's law, with two focused development arenas, namely, IC miniaturization down to nano scale, and SoC based system integration. While the microelectronics community continues to invent new solutions around the world to keep Moore's law alive, there is increasing momentum for the development of 'More than Moore' technologies which are based on silicon technologies but do not simply scale with Moore's law. Typical examples are RF, Power/HV, Passives, Sensor/Actuator/MEMS or Bio-chips. The More than Moore strategy is driven by the increasing social needs for high level heterogeneous system integration including non-digital functions, the necessity to speed up innovative product creation and to broaden the product portfolio of wafer fabs, and the limiting cost and time factors of advanced SoC development. It is believed that More than Moore will add value to society on top of and beyond advanced CMOS with fast increasing marketing potentials. Important key challenges for the realization of the 'More than Moore' strategy are: perspective materials for future THz devices materials systems for embedded sensors and actuators perspective materials for epitaxial approaches material systems for embedded innovative memory technologies development of new materials with customized characteristics The Hot topics covered by the symposium M (More than Moore: Novel materials approaches for functionalized Silicon based Microelectronics) at E-MRS 2012 Spring Meeting, 14-18 May 2012 have been: development of functional ceramics thin films New dielectric materials for advanced microelectronics bio- and CMOS compatible

  18. Isotopic power supplies for space and terrestrial systems: quality assurance by Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Hannigan, R.L.; Harnar, R.R.

    1981-09-01

    The Sandia National Laboratories participation in Quality Assurance (QA) programs for Radioisotopic Thermoelectric Generators which have been used in space and terrestrial systems over the past 15 years is summarized. Basic elements of the program are briefly described and recognition of assistance from other Sandia organizations is included. Descriptions of the various systems for which Sandia has had the QA responsibility are also presented. In addition, the outlook for Sandia participation in RTG programs for the next several years is noted.

  19. Large-Area Laser-Lift-Off Processing in Microelectronics

    Science.gov (United States)

    Delmdahl, R.; Pätzel, R.; Brune, J.

    Laser lift-off is an enabling technology for microelectronics growth markets such as light emitting diodes, densely packaged semiconductor devices, and flexible displays. For example, thin film transistor structures fabricated on top of polymer layers spun on glass carriers must be delaminated from rigid substrates to create lightweight and rugged flexible displays on polymers. Low-thermal-budget processes are generically required to protect adjacent functional films. Excimer lasers provide short UV wavelength and short pulse duration required for highly-localized energy coupling. The high output power of excimer lasers enables a large processing footprint and the high-throughput rates needed in mass manufacturing.

  20. Using SDI-12 with ST microelectronics MCU's

    Energy Technology Data Exchange (ETDEWEB)

    Saari, Alexandra [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hinzey, Shawn Adrian [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Frigo, Janette Rose [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Proicou, Michael Chris [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Borges, Louis [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-09-03

    ST Microelectronics microcontrollers and processors are readily available, capable and economical processors. Unfortunately they lack a broad user base like similar offerings from Texas Instrument, Atmel, or Microchip. All of these devices could be useful in economical devices for remote sensing applications used with environmental sensing. With the increased need for environmental studies, and limited budgets, flexibility in hardware is very important. To that end, and in an effort to increase open support of ST devices, I am sharing my teams' experience in interfacing a common environmental sensor communication protocol (SDI-12) with ST devices.

  1. Laser sintering of thick-film conductors for microelectronic applications

    Science.gov (United States)

    Kinzel, Edward C.; Sigmarsson, Hjalti H.; Xu, Xianfan; Chappell, William J.

    2007-03-01

    This paper investigates fabrication of functional thick metal films using simultaneous laser sintering and patterning along with the fundamental physical phenomena that govern the laser sintering process. The effects of the processing parameters on the quality of the fabricated components are investigated through a heat transfer analysis. We show that our process has potentials for metallization of microelectronics directly onto substrates whose melting temperatures are much lower than the temperature needed for sintering, which is only possible by properly controlling the temperature field during laser sintering. Optimum properties of the fabricated components are obtained when certain thermal conditions are produced during laser heating.

  2. Towards enhancing Sandia's capabilities in multiscale materials modeling and simulation.

    Energy Technology Data Exchange (ETDEWEB)

    Aidun, John Bahram; Fang, Huei Eliot; Barbour, John Charles; Westrich, Henry Roger; Chen, Er-Ping

    2004-01-01

    We report our conclusions in support of the FY 2003 Science and Technology Milestone ST03-3.5. The goal of the milestone was to develop a research plan for expanding Sandia's capabilities in materials modeling and simulation. From inquiries and discussion with technical staff during FY 2003 we conclude that it is premature to formulate the envisioned coordinated research plan. The more appropriate goal is to develop a set of computational tools for making scale transitions and accumulate experience with applying these tools to real test cases so as to enable us to attack each new problem with higher confidence of success.

  3. Micromachined chemical sensor with integrated microelectronics

    Science.gov (United States)

    Smith, J.; Sniegowski, J.; Koehler, D.; Ricco, T.; Martin, S.; McWhorter, P.

    With today's continued emphasis on environmental safety and health issues, a resurgence of interest has developed in the area of chemical sensors. These sensors would typically be used to monitor contamination hazards such as underground storage tanks or to assess previous contamination at waste disposal sites. Human exposure to chemical hazards can also be monitored. Additionally, these sensors can be used as part of a manufacturing process control loop. One type of sensor suitable for gas phase monitoring of chemicals is the quartz resonator or quartz crystal microbalance (QCM) sensor. In this type of sensor, a thickness shear mode (TSM) quartz resonator is coated with a film that interacts with the chemical species of interest. Changes in the mass and elasticity of this film are reflected as changes in the resonant properties of the device. Therefore, the presence of the species of interest can be detected by monitoring the frequency of an oscillator based on the resonance of the quartz. These QCM sensors compete with surface acoustic wave (SAW) devices as a means for monitoring gas phase species. SAW devices are typically more sensitive to small amounts of a species, but the instrumentation associated with a SAW device is an order of magnitude more expensive than the instrumentation associated with a TSM wave resonator since the SAW devices operate in the 100's of MHz frequency regime while quartz resonators operate in the 5-25 MHz regime. We are working to improve the sensitivity of the QCM sensor by increasing the frequency of the device to 25 MHz (compared to the typical 5 MHz crystal) and by increasing the frequency stability of the system to an ultimate goal of 0.1 Hz. The 25 MHz QCM has already been achieved, and once the stability goal is achieved, the QCM will have the same sensitivity as a SAW device.

  4. On the integration of technology readiness levels at Sandia National Laboratories.

    Energy Technology Data Exchange (ETDEWEB)

    Bailey, Beatriz R.; Mitchell, John Anthony

    2006-09-01

    Integrating technology readiness levels (TRL) into the management of engineering projects is critical to the mitigation of risk and improved customer/supplier communications. TRLs provide a common framework and language with which consistent comparisons of different technologies and approaches can be made. At Sandia National Laboratories, where technologies are developed, integrated and deployed into high consequence systems, the use of TRLs may be transformational. They are technology independent and span the full range of technology development including scientific and applied research, identification of customer requirements, modeling and simulation, identification of environments, testing and integration. With this report, we provide a reference set of definitions for TRLs and a brief history of TRLs at Sandia National Laboratories. We then propose and describe two approaches that may be used to integrate TRLs into the NW SMU business practices. In the first approach, we analyze how TRLs can be integrated within concurrent qualification as documented in TBP-100 [1]. In the second approach we take a look at the product realization process (PRP) as documented in TBP-PRP [2]. Both concurrent qualification and product realization are fundamental to the way weapons engineering work is conducted at this laboratory and the NWC (nuclear weapons complex) as a whole. Given the current structure and definitions laid out in the TBP-100 and TBP-PRP, we believe that integrating TRLs into concurrent qualification (TBP-100) rather than TBP-PRP is optimal. Finally, we note that our charter was to explore and develop ways of integrating TRLs into the NW SMU and therefore we do not significantly cover the development and history of TRLs. This work was executed under the auspices and direction of Sandia's Weapon Engineering Program. Please contact Gerry Sleefe, Deputy Program Director, for further information.

  5. Sandia National Laboratories, California Environmental Management System Program Manual.

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L.

    2011-04-01

    The Sandia National Laboratories, California (SNL/CA) Environmental Management System (EMS) Program Manual documents the elements of the site EMS Program. The SNL/CA EMS Program conforms to the International Standard on Environmental Management Systems, ISO 14001:2004and Department of Energy (DOE) Order 450.1. Sandia National Laboratories, California (SNL/CA) has maintained functional environmental programs to assist with regulatory compliance for more than 30 years. During 2005, these existing programs were rolled into a formal environmental management system (EMS) that expands beyond the traditional compliance focus to managing and improving environmental performance and stewardship practices for all site activities. An EMS is a set of inter-related elements that represent a continuing cycle of planning, implementing, evaluating, and improving processes and actions undertaken to achieve environmental policy and goals. The SNL/CA EMS Program conforms to the International Standard for Environmental Management Systems, ISO 14001:2004 (ISO 2004). The site received ISO 14001 certification in September 2006. SNL/CA's EMS Program is applicable to the Sandia, Livermore site only. Although SNL/CA operates as one organizational division of the overall Sandia National Laboratories, the EMS Program is site-specific, with site-specific objectives and targets. SNL/CA (Division 8000) benefits from the organizational structure as it provides corporate level policies, procedures, and standards, and established processes that connect to and support elements of the SNL/CA EMS Program. Additionally, SNL/CA's EMS Program benefits from two corporate functional programs (Facilities Energy Management and Fleet Services programs) that maintain responsibility for energy management and fleet services for all Sandia locations. Each EMS element is further enhanced with site-specific processes and standards. Division 8000 has several groups operating at Sandia National Laboratories

  6. Sandia National Laboratories, California Environmental Management System program manual.

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L.

    2012-03-01

    The Sandia National Laboratories, California (SNL/CA) Environmental Management System (EMS) Program Manual documents the elements of the site EMS Program. The SNL/CA EMS Program conforms to the International Standard on Environmental Management Systems, ISO 14001:2004and Department of Energy (DOE) Order 436.1. Sandia National Laboratories, California (SNL/CA) has maintained functional environmental programs to assist with regulatory compliance for more than 30 years. During 2005, these existing programs were rolled into a formal environmental management system (EMS) that expands beyond the traditional compliance focus to managing and improving environmental performance and stewardship practices for all site activities. An EMS is a set of inter-related elements that represent a continuing cycle of planning, implementing, evaluating, and improving processes and actions undertaken to achieve environmental policy and goals. The SNL/CA EMS Program conforms to the International Standard for Environmental Management Systems, ISO 14001:2004 (ISO 2004). The site first received ISO 14001 certification in September 2006 and recertification in 2009. SNL/CA's EMS Program is applicable to the Sandia, Livermore site only. Although SNL/CA operates as one organizational division of the overall Sandia National Laboratories, the EMS Program is site-specific, with site-specific objectives and targets. SNL/CA (Division 8000) benefits from the organizational structure as it provides corporate level policies, procedures, and standards, and established processes that connect to and support elements of the SNL/CA EMS Program. Additionally, SNL/CA's EMS Program benefits from two corporate functional programs (Facilities Energy and Water Resource Management and Fleet Services programs) that maintain responsibility for energy management and fleet services for all Sandia locations. Each EMS element is further enhanced with site-specific processes and standards. Division 8000 has

  7. Sandia National Laboratories, California Environmental Management System Program Manual.

    Energy Technology Data Exchange (ETDEWEB)

    2009-04-01

    The Sandia National Laboratories, California (SNL/CA) Environmental Management System (EMS) Program Manual documents the elements of the site EMS Program. The SNL/CA EMS Program conforms to the International Standard on Environmental Management Systems, ISO 14001:2004 and Department of Energy (DOE) Order 450.1. Sandia National Laboratories, California (SNL/CA) has maintained functional environmental programs to assist with regulatory compliance for more than 30 years. During 2005, these existing programs were rolled into a formal environmental management system (EMS) that expands beyond the traditional compliance focus to managing and improving environmental performance and stewardship practices for all site activities. An EMS is a set of inter-related elements that represent a continuing cycle of planning, implementing, evaluating, and improving processes and actions undertaken to achieve environmental policy and goals. The SNL/CA EMS Program conforms to the International Standard for Environmental Management Systems, ISO 14001:2004 (ISO 2004). The site received ISO 14001 certification in September 2006. SNL/CA's EMS Program is applicable to the Sandia, Livermore site only. Although SNL/CA operates as one organizational division of the overall Sandia National Laboratories, the EMS Program is site-specific, with site-specific objectives and targets. SNL/CA (Division 8000) benefits from the organizational structure as it provides corporate level policies, procedures, and standards, and established processes that connect to and support elements of the SNL/CA EMS Program. Additionally, SNL/CA's EMS Program benefits from two corporate functional programs (Facilities Energy Management and Fleet Services Environmental programs) that maintain responsibility for energy management and fleet services for all Sandia locations. Each EMS element is further enhanced with site-specific processes and standards. Division 8000 has several groups operating at Sandia

  8. Microelectronics at Work: Productivity and Jobs in the World Economy. Worldwatch Paper 39.

    Science.gov (United States)

    Norman, Colin

    A combination of revitalized employment policies, greater industrial democracy, and new ways of distributing both the hours of work and the fruits of technological change are essential if the benefits of the microelectronic revolution are to be equitably shared. Microelectronic technology promises an array of benefits, and the electronic age is…

  9. Synthesis оf Optoelectronic System for Control оf Microelectronic Structures

    Directory of Open Access Journals (Sweden)

    G. A. Trapashko

    2014-01-01

    Full Text Available Development of optoelectronic systems for registration of structuring element images demands improvement of the equipment for control of sizes and a form of microelectronic structures in accordance with design data and absence of introduced defects and impurities. For synthesis of these systems it is necessary to use a special method which allows to substantiate the use of a radiation source in it and  determine main functional parameters of the optoelectronic system. The paper presents the results of the method that has been used for development of the optoelectronic system operating  with the resolution of 250 nanometers. It has been shown that LED lamps can be used instead of traditionally used halogen and mercury-xenon lamps in the control equipment.

  10. A brief history of Sandia's National security missions.

    Energy Technology Data Exchange (ETDEWEB)

    Drewien, Celeste A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); O' Canna, Myra Lynn [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stikar, John Anthony. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-09-01

    To help members of the workforce understand what factors contribute to Sandia National Laboratories national security mission, the authors describe the evolution of Sandias core mission and its other mission components. The mission of Sandia first as a division of Los Alamos and later as Sandia Corporation underlies our core nuclear weapon mission of today. Sandias mission changed in 1963 and twice more in the 1970s. This report should help staff and management appreciate the need for mission evolution. A clear definition and communication of a consistent corporate mission statement is still needed.

  11. Active microelectronic array system for DNA hybridization, genotyping and pharmacogenomic applications.

    Science.gov (United States)

    Sosnowski, Ron; Heller, Michael J; Tu, Eugene; Forster, Anita H; Radtkey, Ray

    2002-12-01

    Microelectronic arrays have been developed for DNA hybridization analysis of point mutations, single nucleotide polymorphisms, short tandem repeats and gene expression. In addition to a variety of molecular biology and genomic research applications, such devices will also be used for infectious disease detection, genetic and cancer diagnostics, and pharmacogenomic applications. These microelectronic array devices are able to produce defined electric fields on their surfaces that allow charged molecules and other entities to be transported to or from any test site or micro-location on the planar surface of the device. These molecules and entities include DNA, RNA, proteins, enzymes, antibodies and cells. Electronic-based molecule addressing and hybridization can then be carried out, where the electric field is now used to greatly accelerate the hybridization reactions that occur on the selected test sites. When reversed, the electric field can be used to provide an additional parameter for improved hybridization. Special low-conductance buffers have been developed that provide for the rapid transport of the DNA molecules and facilitate the electronic hybridization reactions under conditions that do not support hybridization. Important to the device function is the permeation layer that overcoats the underlying microelectrodes. Generally composed of a porous hydrogel material impregnated with attachment chemistry, this permeation layer prevents the destruction of analytes at the active microelectrode surface, ameliorates the adverse effects of electrolysis products on the sensitive hybridization and affinity reactions, and serves as a support structure for attaching DNA probes and other molecules to the array. The microelectronic chip or array device is incorporated into a cartridge package (NanoChip trade mark cartridge) that provides the electronic, optical, and fluidic interfacing. A complete instrument system (NanoChip trade mark Molecular Biology Workstation

  12. Procedure to Determine Coefficients for the Sandia Array Performance Model (SAPM)

    Energy Technology Data Exchange (ETDEWEB)

    King, Bruce Hardison; Hansen, Clifford; Riley, Daniel; Robinson, Charles David; Pratt, Larry

    2016-06-01

    The Sandia Array Performance Model (SAPM), a semi-empirical model for predicting PV system power, has been in use for more than a decade. While several studies have presented comparisons of measurements and analysis results among laboratories, detailed procedures for determining model coefficients have not yet been published. Independent test laboratories must develop in-house procedures to determine SAPM coefficients, which contributes to uncertainty in the resulting models. Here we present a standard procedure for calibrating the SAPM using outdoor electrical and meteorological measurements. Analysis procedures are illustrated with data measured outdoors for a 36-cell silicon photovoltaic module.

  13. National Environmental Policy Act (NEPA) Compliance Guide, Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, R.P. [Hansen Environmental Consultants, Englewood, CO (United States)

    1995-08-01

    This report contains a comprehensive National Environmental Policy Act (NEPA) Compliance Guide for the Sandia National Laboratories. It is based on the Council on Environmental Quality (CEQ) NEPA regulations in 40 CFR Parts 1500 through 1508; the US Department of Energy (DOE) N-EPA implementing procedures in 10 CFR Part 102 1; DOE Order 5440.1E; the DOE ``Secretarial Policy Statement on the National Environmental Policy Act`` of June 1994- Sandia NEPA compliance procedures-, and other CEQ and DOE guidance. The Guide includes step-by-step procedures for preparation of Environmental Checklists/Action Descriptions Memoranda (ECL/ADMs), Environmental Assessments (EAs), and Environmental Impact Statements (EISs). It also includes sections on ``Dealing With NEPA Documentation Problems`` and ``Special N-EPA Compliance Issues.``

  14. 1980 environmental monitoring report, Sandia National Laboratories, Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Millard, G.C.; Simmons, T.N.; Gray, C.E.; O' Neal, B.L.

    1981-04-01

    Sandia National Laboratories in Albuquerque is located south of the city on two broad mesas. The local climate is arid continental. Radionuclides are potentially released from five technical areas from the Laboratories' research activities. Sandia's environmental monitoring program searches for cesium-137, tritium, uranium, alpha emitters, and beta emitters in water, soil, air, and vegetation. No activity was found in public areas in excess of that found in local background in 1980. The Albuquerque population receives only 0.11 person-rem (estimated) from airborne radioactive releases. While national security research is the Laboratories' major responsibility, energy research is a major area of activity. Both these research areas cause radioactive releases.

  15. Sandia and the Waste Isolation Pilot Plant, 1974--1999

    Energy Technology Data Exchange (ETDEWEB)

    MORA,CARL J.

    2000-04-11

    Engineers have learned to design and build big projects, which certainly describes the WIPP project, but also includes defense projects, highway networks, space exploration, the Internet, etc., through what has been called a messily complex embracing of contradictions. When something massive and complicated has to be built these days, it leads to a protracted political process in which every special interest makes a stand, lobbyists exert what influence they can, lawmakers bicker, contractors change things, Congress struggles with costs, environmentalists hold things up--and this is good. It may seem amazing that anything gets done, but when it does, everyone has had their say. It's an intensely democratic, even if expensive and time-consuming, process. The corporate historian of Sandia National Laboratories presents a unique background of the WIPP project and Sandia's part in it.

  16. 1994 Site Environmental Report Sandia National Laboratories Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Shyr, L.J.; Wiggins, T.; White, B.B. [eds.] [and others

    1995-09-01

    This 1994 report contains data from routine radiological and nonradiological environmental monitoring activities. Summaries of significant environmental compliance programs in progress, such as National Environmental Policy Act documentation, environmental permits, environmental restoration, and various waste management programs for Sandia National Laboratories in Albuquerque, New Mexico, are included. The maximum off-site dose impact from air emissions was calculated to be 1.5 x 10{sup -4} millirem. The total population within a 50-mile radius of Sandia National Laboratories/New Mexico received an estimated collective dose of 0.012 person-rem during 1994 from the laboratories` operations. This report is prepared for the U.S. Department of Energy in compliance with DOE Order 5400.1.

  17. Sandia equation of state data base: seslan File

    Energy Technology Data Exchange (ETDEWEB)

    Kerley, G.I. [Sandia National Labs., Albuquerque, NM (US); Christian-Frear, T.L. [RE/SPEC Inc., Albuquerque, NM (US)

    1993-06-24

    Sandia National Laboratories maintains several libraries of equation of state tables, in a modified Sesame format, for use in hydrocode calculations and other applications. This report discusses one of those libraries, the seslan file, which contains 78 tables from the Los Alamos equation of state library. Minor changes have been made to these tables, making them more convenient for code users and reducing numerical difficulties that occasionally arise in hydrocode calculations.

  18. Sandia National Laboratories, California Waste Management Program annual report.

    Energy Technology Data Exchange (ETDEWEB)

    Brynildson, Mark E.

    2010-02-01

    The annual program report provides detailed information about all aspects of the Sandia National Laboratories, California (SNL/CA) Waste Management Program. It functions as supporting documentation to the SNL/CA Environmental Management System Program Manual. This annual program report describes the activities undertaken during the past year, and activities planned in future years to implement the Waste Management (WM) Program, one of six programs that supports environmental management at SNL/CA.

  19. Implementing a lessons learned process at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Fosshage, Erik D.; Drewien, Celeste A.; Eras, Kenneth; Hartwig, Ronald Craig; Post, Debra S.; Stoecker, Nora Kathleen

    2016-01-01

    The Lessons Learned Process Improvement Team was tasked to gain an understanding of the existing lessons learned environment within the major programs at Sandia National Laboratories, identify opportunities for improvement in that environment as compared to desired attributes, propose alternative implementations to address existing inefficiencies, perform qualitative evaluations of alternative implementations, and recommend one or more near-term activities for prototyping and/or implementation. This report documents the work and findings of the team.

  20. Sandia non-fusion R&D supported by FES.

    Energy Technology Data Exchange (ETDEWEB)

    Nygren, Richard E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-06-03

    Until 2012, Sandia participated regularly in non-fusion R&D that was supported primarily through our collaborations with companies in the DOE program for Small Business Innovative Research but also in some work-for-others contracts. In this work, funds were recovered from collaborating institutions for the staff time and materials used, but FES had supported the facility itself and in doing so enabled the contributions to the non-fusion R&D below.

  1. Sandia wind program FY94 annual operating plan

    Energy Technology Data Exchange (ETDEWEB)

    Dodd, H.M.

    1993-10-01

    This document presents the objectives, accomplishments and activity plan for the Sandia Wind Energy Technology Program. The status of the current program is summarized and the planned FY94 activities are defined. Appendices detailing the cost, performance and schedule associated with these activities are also included. Funding requirements are given for several scenarios in order to reflect the impact of funding variability on program progress.

  2. Sandia National Laboratories, California Hazardous Materials Management Program annual report.

    Energy Technology Data Exchange (ETDEWEB)

    Brynildson, Mark E.

    2011-02-01

    The annual program report provides detailed information about all aspects of the Sandia National Laboratories, California (SNL/CA) Hazardous Materials Management Program. It functions as supporting documentation to the SNL/CA Environmental Management System Program Manual. This program annual report describes the activities undertaken during the calender past year, and activities planned in future years to implement the Hazardous Materials Management Program, one of six programs that supports environmental management at SNL/CA.

  3. Megaamps, Megagauss, and Megabars: Using the Sandia Z Machine to perform extreme material dynamics experiments

    Science.gov (United States)

    Knudson, Marcus

    2011-06-01

    Pulsed power devices are quite efficient at producing very large pulsed current and magnetic field densities. The corresponding Lorentz forces enable these devices to be used very effectively in material dynamics experiments. For the past decade, a large, interdisciplinary team at Sandia National Laboratories has been refining the Z Machine (20+ MA and 10+ MGauss) into a mature, robust, and precise platform for such studies in the multi-Mbar pressure regime. In particular, significant effort has gone into effectively coupling condensed matter theory, magneto-hydrodynamic simulation, and electromagnetic modeling to produce a fully self-consistent simulation capability able to very accurately predict the performance of the Z machine and various experimental load configurations. This capability has been instrumental in the ability to develop experimental platforms to routinely perform magnetic ramp compression experiments to over 4 Mbar, and magnetically accelerate flyer plates to over 40 km/s, creating over 20 Mbar impact pressures. Furthermore, a strong tie has been developed between the condensed matter theory and the experimental program. This coupling has been proven time and again to be extremely fruitful, with the capability of both theory and experiment being challenged and advanced through this close interrelationship. This talk will provide an overview of the material dynamics platform and discuss several examples of the use of Z to perform extreme material dynamics studies with unprecedented accuracy in support of basic science, planetary astrophysics, inertial confinement fusion, and the emerging field of high energy density laboratory physics. Sandia is a multiprogram laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Company, for the US Department of Energy's National Nuclear Security Administration under Contract No. DE-ACO4-94AL85000.

  4. Site Environmental Report for 2010 Sandia National Laboratories, California.

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Barbara L.

    2011-06-01

    Sandia National Laboratories, California (SNL/CA) is a government-owned/contractor-operated laboratory. Sandia Corporation, a Lockheed Martin Company, manages and operates the laboratory for the Department of Energy's National Nuclear Security Administration (NNSA). The NNSA Sandia Site Office administers the contract and oversees contractor operations at the site. This Site Environmental Report for 2010 was prepared in accordance with DOE Order 231.1A (DOE 2004a). The report provides a summary of environmental monitoring information and compliance activities that occurred at SNL/CA during calendar year 2010. General site and environmental program information is also included. The Site Environmental Report is divided into ten chapters. Chapter 1, the Executive Summary, highlights compliance and monitoring results obtained in 2010. Chapter 2 provides a brief introduction to SNL/CA and the existing environment found on site. Chapter 3 summarizes SNL/CA's compliance activities with the major environmental requirements applicable to site operations. Chapter 4 presents information on environmental management, performance measures, and environmental programs. Chapter 5 presents the results of monitoring and surveillance activities in 2010. Chapter 6 discusses quality assurance. Chapters 7 through 9 provide supporting information for the report and Chapter 10 is the report distribution list.

  5. Sandia_HighTemperatureComponentEvaluation_2015

    Energy Technology Data Exchange (ETDEWEB)

    Cashion, Avery T. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-03-01

    The objective of this project is to perform independent evaluation of high temperature components to determine their suitability for use in high temperature geothermal tools. Development of high temperature components has been increasing rapidly due to demand from the high temperature oil and gas exploration and aerospace industries. Many of these new components are at the late prototype or first production stage of development and could benefit from third party evaluation of functionality and lifetime at elevated temperatures. In addition to independent testing of new components, this project recognizes that there is a paucity of commercial-off-the-shelf COTS components rated for geothermal temperatures. As such, high-temperature circuit designers often must dedicate considerable time and resources to determine if a component exists that they may be able to knead performance out of to meet their requirements. This project aids tool developers by characterization of select COTS component performances beyond published temperature specifications. The process for selecting components includes public announcements of project intent (e.g., FedBizOps), direct discussions with candidate manufacturers,and coordination with other DOE funded programs.

  6. Evaluation of advanced microelectronics for inclusion in MIL-STD-975

    Science.gov (United States)

    Scott, W. Richard

    1991-03-01

    The approach taken by NASA and JPL (Jet Propulsion Laboratory) in the development of a MIL-STD-975 section which contains advanced technology such as Large Scale Integration and Very Large Scale Integration (LSI/VLSI) microelectronic devices is described. The parts listed in this section are recommended as satisfactory for NASA flight applications, in the absence of alternate qualified devices, based on satisfactory results of a vendor capability audit, the availability of sufficient characterization and reliability data from the manufacturers and users and negotiated detail procurement specifications. The criteria used in the selection and evaluation of the vendors and candidate parts, the preparation of procurement specifications, and the status of this activity are discussed.

  7. West Europe report: Science and technology. FRG: Concept paper on microelectronics, communications technology

    Science.gov (United States)

    1984-07-01

    Precisely because the Federal Republic of Germany is a nation with a strong export orientation the capability to develop and apply, with an eye to the market, modern information and communication technologies and microelectronics which provides the basis for them has a very important bearing on the nations competitive position. To attain a leadership position in information technology, the men and women of the FRG must take up the challenge of this technology in terms of training and continuing education as well as in the media and in public life. Industry must agressively seek out markets and engage in international competition and the state must remove existing obstacles and create the kind of conditions that will make its assistance programs most effective. Programs which reflect the government's resolve to meet the challenge of information technology and to help improve the FRG's competitive position in this field are outlined.

  8. Application of non-cyanide gold for selective plating of microelectronic circuits

    Energy Technology Data Exchange (ETDEWEB)

    Worobey, W.; Rieger, D.

    1991-01-01

    With the current trends towards miniaturization, high performance, high quality and cost competiveness, the electrodeposition process has become an important manufacturing technology in many new microelectronic applications. Gold electrodeposition plays an increasing role in processes that require this noble metal. Added to these trends is the continuing and increasing emphasis on manufacturing processes which are less damaging to the environment and potentially less hazardous to the operator and personnel in the vicinity of the operation. The present standard gold plating solutions are based on cyanide salts and are considered acutely hazardous solutions. The trend away from their use is gaining momentum as new non-hazardous gold plating solutions and manufacturing processes making use of them are developed. 2 refs.

  9. Microelectronic DNA assay for the detection of BRCA1 gene mutations

    Science.gov (United States)

    Chen, Hua; Han, Jie; Li, Jun; Meyyappan, Meyya

    2004-01-01

    Mutations in BRCA1 are characterized by predisposition to breast cancer, ovarian cancer and prostate cancer as well as colon cancer. Prognosis for this cancer survival depends upon the stage at which cancer is diagnosed. Reliable and rapid mutation detection is crucial for the early diagnosis and treatment. We developed an electronic assay for the detection of a representative single nucleotide polymorphism (SNP), deletion and insertion in BRCA1 gene by the microelectronics microarray instrumentation. The assay is rapid, and it takes 30 minutes for the immobilization of target DNA samples, hybridization, washing and readout. The assay is multiplexing since it is carried out at the same temperature and buffer conditions for each step. The assay is also highly specific, as the signal-to-noise ratio is much larger than recommended value (72.86 to 321.05 vs. 5) for homozygotes genotyping, and signal ratio close to the perfect value 1 for heterozygotes genotyping (1.04).

  10. Simulation of ion beam induced current in radiation detectors and microelectronic devices.

    Energy Technology Data Exchange (ETDEWEB)

    Vizkelethy, Gyorgy

    2009-10-01

    Ionizing radiation is known to cause Single Event Effects (SEE) in a variety of electronic devices. The mechanism that leads to these SEEs is current induced by the radiation in these devices. While this phenomenon is detrimental in ICs, this is the basic mechanism behind the operation of semiconductor radiation detectors. To be able to predict SEEs in ICs and detector responses we need to be able to simulate the radiation induced current as the function of time. There are analytical models, which work for very simple detector configurations, but fail for anything more complex. On the other end, TCAD programs can simulate this process in microelectronic devices, but these TCAD codes costs hundreds of thousands of dollars and they require huge computing resources. In addition, in certain cases they fail to predict the correct behavior. A simulation model based on the Gunn theorem was developed and used with the COMSOL Multiphysics framework.

  11. SAVANT analysis of the microelectronics and photonics testbed solar cell data

    Energy Technology Data Exchange (ETDEWEB)

    Walters, Robert J.; Summers, G.P. [Naval Research Lab., Code 6818, Washington, DC (United States); Messenger, S.R. [SFA, Inc., Largo, MD (United States); Morton, T.L. [Ohio Aerospace Inst., Cleveland, OH (United States)

    2005-07-01

    An analysis of solar array data from the Microelectronic and Photonic Testbed (MPTB) space experiment is presented. The data are analyzed using the displacement damage dose (D{sub d}) methodology developed by the US Naval Research Laboratory (NRL) as implemented in the Solar Array Verification and Analysis Tool (SAVANT). SAVANT is a WindowsTM-based computer code that predicts the on-orbit performance of a solar cell in a specified Earth orbit. The predicted solar cell performance produced by the SAVANT code are compared with the measured on-orbit data. In addition, the calculated data are compared with onboard dosimeter measurements. The results allow both a validation of the SAVANT code and a comparison of the space environment models with measured on-orbit data. The results show the models to match the measured data within a factor of 2. (Author)

  12. Technical Challenges in Reliable Microelectronics Packaging of Microelectromechanical Systems (MEMS) for Space Applications

    Science.gov (United States)

    Ramesham, Rajeshuni

    2000-01-01

    MEMS have shown a significant promise in the last decade for a variety of applications such as air-bag, pressure sensors, accelerometer, microgyro, chemical sensors, artificial nose, etc. Standard semiconductor microelectronics packaging needs the integrated circuits (IC) to be protected from the harsh environment, and provide electrical communication with the other parts of the circuit, facilitate thermal dissipation efficiently, and impart mechanical strength to the silicon die. Microelectronics packaging involves wafer dicing, bonding, lead attachment, encapsulation to protect from the environment, electrical integrity, and package leak tests to assure the reliable IC packaging technology. Active elements or microstructures in MEMS devices often interfaces with the hostile environment where packaging leak tests and testing of such devices using chemical and mechanical parameters will be very difficult and expensive. Packaging of MEMS is significantly complex as they serve to protect from the environment and microstructures interact with the same environment to measure or affect the desired physical or chemical parameters. The most of the silicon circuitry is sensitive to temperature, moisture, magnetic field, light, and electromagnetic interference. The package must then protect the on-board silicon circuitry while simultaneously exposing the microsensor to the effect it measures to assure the packaging technology of MEMS. MEMS technology has a major application in developing a microspacecraft for space systems provided reliability of MEMS packaging technology is sufficiently addressed. This MEMS technology would eventually miniaturize many of the components of the spacecraft to reach the NASA's goal by building faster, cheaper, better, smaller spacecraft to explore the space more effectively. This paper discusses the latest developments in the MEMS technology and challenging technical issues in the packaging of hermetically sealed and non-hermetically sealed

  13. Sandia computerized shock compression bibliographical database

    Energy Technology Data Exchange (ETDEWEB)

    Wilbeck, J.S.; Anderson, C.E.; Hokanson, J.C.; Asay, J.R.; Grady, D.E.; Graham, R.A.; Kipp, M.E.

    1985-01-01

    A searchable and updateable bibliographical database is being developed which will be designed, controlled, and evaluated by working technical experts in the field of shock-compression science. It will emphasize shock-compression properties in the stress region of a few tens of GPa and provide a broad and complete base of bibliographical information on the shock-compression behavior of materials. Through the operation of technical advisors, the database provides authoritative blbliographical and keyword data for use by both the inexperienced and expert user. In its current form, it consists of: (1) a library of journal articles, reports, books, and symposia papers in the areas of shock physics and shock mechanics; and (2) a computerized database system containing complete bibliographical information, exhaustive keyword descriptions, and author abstracts for each of the documents in the database library.

  14. Pulsed Power: Sandia's Plans for the New Millenium

    Energy Technology Data Exchange (ETDEWEB)

    QUINTENZ,JEFFREY P.

    2000-07-20

    Pulsed power science and engineering activities at Sandia National Laboratories grew out of a programmatic need for intense radiation sources to advance capabilities in radiographic imaging and to create environments for testing and certifying the hardness of components and systems to radiation in hostile environments. By the early 1970s, scientists in laboratories around the world began utilizing pulsed power drivers with very short (10s of nanoseconds) pulse lengths for Inertial Confinement Fusion (ICF) experiments. In the United States, Defense Programs within the Department of Energy has sponsored this research. Recent progress in pulsed power, specifically fast-pulsed-power-driven z pinches, in creating temperatures relevant to ICF has been remarkable. Worldwide developments in pulsed power technologies and increased applications in both defense and industry are contrasted with ever increasing stress on research and development tiding. The current environment has prompted us at Sandia to evaluate our role in the continued development of pulsed power science and to consider options for the future. This presentation will highlight our recent progress and provide an overview of our plans as we begin the new millennium.

  15. Miniature environmental chambers for temperature humidity bias testing of microelectronics.

    Science.gov (United States)

    Hook, Michael David; Mayer, Michael

    2017-03-01

    Environmental chambers are commonly used for reliability testing of microelectronics and other products and materials. These chambers are large, expensive, and limit electrical connectivity to devices under test. In this paper, we present a collection of ten small, low-cost environmental chambers, with humidity control based on mixtures of water and glycerol placed inside the chambers. We demonstrate relative humidities from 44% to 90%, at temperatures from 30 to 85 °C, enabling industry-standard testing at 85% humidity and 85 °C. The division of samples between ten separate chambers allows different conditions to be applied to each sample, in order to quickly characterize the effects of the environment on device reliability, enabling extrapolation to estimate lifetimes in working conditions.

  16. Pattern-integrated interference lithography: prospects for nano- and microelectronics.

    Science.gov (United States)

    Leibovici, Matthieu C R; Burrow, Guy M; Gaylord, Thomas K

    2012-10-08

    In recent years, limitations in optical lithography have challenged the cost-effective manufacture of nano- and microelectronic chips. Spatially regular designs have been introduced to improve manufacturability. However, regular designed layouts typically require an interference step followed by a trim step. These multiple steps increase cost and reduce yield. In the present work, Pattern-Integrated Interference Lithography (PIIL) is introduced to address this problem. PIIL is the integration of interference lithography and superposed pattern mask imaging, combining the interference and the trim into a single-exposure step. Example PIIL implementations and experimental demonstrations are presented. The degrees of freedom associated with the source, pattern mask, and Fourier filter designs are described.

  17. Thermal and Electrical Characterization of Alumina Substrate for Microelectronic Applications

    Science.gov (United States)

    Ahmad, S.; Ibrahim, A.; Alias, R.; Shapee, S. M.; Ambak, Z.; Zakaria, S. Z.; Yahya, M. R.; Mat, A. F. A.

    2010-03-01

    This paper reports the effect of sintering temperature on thermal and electrical properties of alumina material as substrate for microelectronic devices. Alumina materials in the form of green sheet with 1 mm thickness were sintered at 1100° C, 1300° C and 1500° C for about 20 hours using heating and cooling rates of 2° C/min. The densities were measured using densitometer and the microstructures of the samples were analyzed using SEM micrographs. Meanwhile thermal and electrical properties of the samples were measured using flash method and impedance analyzer respectively. It was found that thermal conductivity and thermal diffusivity of the substrate increases as sintering temperature increases. It was found also that the dielectric constant of alumina substrate increases as the sintering temperature increases.

  18. Thermal measurement. Nanoscale temperature mapping in operating microelectronic devices.

    Science.gov (United States)

    Mecklenburg, Matthew; Hubbard, William A; White, E R; Dhall, Rohan; Cronin, Stephen B; Aloni, Shaul; Regan, B C

    2015-02-06

    Modern microelectronic devices have nanoscale features that dissipate power nonuniformly, but fundamental physical limits frustrate efforts to detect the resulting temperature gradients. Contact thermometers disturb the temperature of a small system, while radiation thermometers struggle to beat the diffraction limit. Exploiting the same physics as Fahrenheit's glass-bulb thermometer, we mapped the thermal expansion of Joule-heated, 80-nanometer-thick aluminum wires by precisely measuring changes in density. With a scanning transmission electron microscope and electron energy loss spectroscopy, we quantified the local density via the energy of aluminum's bulk plasmon. Rescaling density to temperature yields maps with a statistical precision of 3 kelvin/hertz(-1/2), an accuracy of 10%, and nanometer-scale resolution. Many common metals and semiconductors have sufficiently sharp plasmon resonances to serve as their own thermometers. Copyright © 2015, American Association for the Advancement of Science.

  19. Sandia National Laboratories support of the Iraq Nuclear Facility Dismantlement and Disposal Program.

    Energy Technology Data Exchange (ETDEWEB)

    Cochran, John Russell; Danneels, Jeffrey John

    2009-03-01

    Because of past military operations, lack of upkeep and looting there are now enormous radioactive waste problems in Iraq. These waste problems include destroyed nuclear facilities, uncharacterized radioactive wastes, liquid radioactive waste in underground tanks, wastes related to the production of yellow cake, sealed radioactive sources, activated metals and contaminated metals that must be constantly guarded. Iraq currently lacks the trained personnel, regulatory and physical infrastructure to safely and securely manage these facilities and wastes. In 2005 the International Atomic Energy Agency (IAEA) agreed to organize an international cooperative program to assist Iraq with these issues. Soon after, the Iraq Nuclear Facility Dismantlement and Disposal Program (the NDs Program) was initiated by the U.S. Department of State (DOS) to support the IAEA and assist the Government of Iraq (GOI) in eliminating the threats from poorly controlled radioactive materials. The Iraq NDs Program is providing support for the IAEA plus training, consultation and limited equipment to the GOI. The GOI owns the problems and will be responsible for implementation of the Iraq NDs Program. Sandia National Laboratories (Sandia) is a part of the DOS's team implementing the Iraq NDs Program. This report documents Sandia's support of the Iraq NDs Program, which has developed into three principal work streams: (1) training and technical consultation; (2) introducing Iraqis to modern decommissioning and waste management practices; and (3) supporting the IAEA, as they assist the GOI. Examples of each of these work streams include: (1) presentation of a three-day training workshop on 'Practical Concepts for Safe Disposal of Low-Level Radioactive Waste in Arid Settings;' (2) leading GOI representatives on a tour of two operating low level radioactive waste disposal facilities in the U.S.; and (3) supporting the IAEA's Technical Meeting with the GOI from April 21

  20. Sandia National Laboratories site-wide hydrogeologic characterization project calendar year 1992 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Crowson, D.; Gibson, J.D.; Haase, C.S.; Holt, R.; Hyndman, D.; Krumhansl, J.; Lauffer, F.; McCord, J.P.; McCord, J.T.; Neel, D. [and others

    1993-10-01

    The Sandia National Laboratories, New Mexico (SNL/NM) Site-Wide Hydrogeologic Characterization (SWHC) project has been implemented as part of the SNL/NM Environmental Restoration (ER) Program to develop the regional hydrogeologic framework and baseline for the approximately 100 mi of Kirtland Air Force Base (KAFB) and adjacent withdrawn public lands upon which SNL/NM has performed research and development activities. Additionally, the SWHC project will investigate and characterize generic hydrogeologic issues associated with the 172 ER sites owned by SNL/NM across its facilities on KAFB. As called for in the Hazardous and Solid Waste Amendments (HSWA) to the Resource Conservation and Recovery Act (RCRA) Part B permit agreement between the U.S. Environmental Protection Agency (EPA) as the permitter and the U.S. Department of Energy (DOE) and SNL/NM as the permittees, an annual report is to be prepared by the SWHC project team. This document serves two primary purposes: (1) to identify and describe the conceptual framework for the hydrogeologic system underlying SNL/NM and (2) to describe characterization activities undertaken in the preceding year that add to our understanding (reduce our uncertainties) regarding the conceptual and quantitative hydrogeologic framework. This SWHC project annual report focuses primarily on purpose 1, providing a summary description of the current {open_quotes}state of knowledge{close_quotes} of the Sandia National Laboratories/Kirtland Air Force Base (SNL/KAFB) hydrogeologic setting.

  1. Sandia National Laboratories environmental fluid dynamics code. Marine Hydrokinetic Module User's Manual

    Energy Technology Data Exchange (ETDEWEB)

    James, Scott Carlton; Roberts, Jesse D

    2014-03-01

    This document describes the marine hydrokinetic (MHK) input file and subroutines for the Sandia National Laboratories Environmental Fluid Dynamics Code (SNL-EFDC), which is a combined hydrodynamic, sediment transport, and water quality model based on the Environmental Fluid Dynamics Code (EFDC) developed by John Hamrick [1], formerly sponsored by the U.S. Environmental Protection Agency, and now maintained by Tetra Tech, Inc. SNL-EFDC has been previously enhanced with the incorporation of the SEDZLJ sediment dynamics model developed by Ziegler, Lick, and Jones [2-4]. SNL-EFDC has also been upgraded to more accurately simulate algae growth with specific application to optimizing biomass in an open-channel raceway for biofuels production [5]. A detailed description of the input file containing data describing the MHK device/array is provided, along with a description of the MHK FORTRAN routine. Both a theoretical description of the MHK dynamics as incorporated into SNL-EFDC and an explanation of the source code are provided. This user manual is meant to be used in conjunction with the original EFDC [6] and sediment dynamics SNL-EFDC manuals [7]. Through this document, the authors provide information for users who wish to model the effects of an MHK device (or array of devices) on a flow system with EFDC and who also seek a clear understanding of the source code, which is available from staff in the Water Power Technologies Department at Sandia National Laboratories, Albuquerque, New Mexico.

  2. The economic impact of Sandia National Laboratories on central New Mexico and the state of New Mexico fiscal year 1997

    Energy Technology Data Exchange (ETDEWEB)

    Lansford, R.R.; Nielsen, T.G.; Schultz, J. [New Mexico State Univ., Las Cruces, NM (United States); Adcock, L.D.; Gentry, L.M. [Dept. of Energy, Albuquerque, NM (United States). Albuquerque Operations Office; Ben-David, S. [Univ. of New Mexico, Albuquerque, NM (United States). Dept. of Economics; Temple, J. [Temple (John), Albuquerque, NM (United States)

    1998-05-29

    Sandia National Laboratories (SNL) was established in 1949 to perform the engineering development and ordnance responsibilities associated with nuclear weapons. By the early 1960`s the facility had evolved into an engineering research and development laboratory and became a multiprogram laboratory during the 1970s. Sandia is operated for the US Department of Energy by the Sandia Corporation, a wholly-owned subsidiary of Lockheed Martin, Incorporated. For several years, the US Department of Energy (DOE) Albuquerque Operations Office (AL) and New Mexico State University (NMSU) have maintained an inter-industry, input-output model with capabilities to assess the impacts of developments initiated outside the economy such as federal DOE monies that flow into the state, on an economy. This model will be used to assess economic, personal income and employment impacts of SNL on central New Mexico and the state of New Mexico. For this report, the reference period is FY 1997 (October 1, 1996, through September 30, 1997) and includes two major impact analyses: the impact of SNL activities on central New Mexico and the economic impacts of SNL on the state of New Mexico. For purposes of this report, the central New Mexico region includes Bernalillo, Sandoval, Valencia, and Torrance counties. Total impact represents both direct and indirect respending by business, including induced effects (respending by households). The standard multipliers used in determining impacts results from the inter-industry, input-output models developed for the four-county region and the state of New Mexico. 6 figs., 10 tabs.

  3. Sandia National Laboratories, California Chemical Management Program annual report.

    Energy Technology Data Exchange (ETDEWEB)

    Brynildson, Mark E.

    2012-02-01

    The annual program report provides detailed information about all aspects of the Sandia National Laboratories, California (SNL/CA) Chemical Management Program. It functions as supporting documentation to the SNL/CA Environmental Management System Program Manual. This program annual report describes the activities undertaken during the calender past year, and activities planned in future years to implement the Chemical Management Program, one of six programs that supports environmental management at SNL/CA. SNL/CA is responsible for tracking chemicals (chemical and biological materials), providing Material Safety Data Sheets (MSDS) and for regulatory compliance reporting according to a variety of chemical regulations. The principal regulations for chemical tracking are the Emergency Planning Community Right-to-Know Act (EPCRA) and the California Right-to-Know regulations. The regulations, the Hazard Communication/Lab Standard of the Occupational Safety and Health Administration (OSHA) are also key to the CM Program. The CM Program is also responsible for supporting chemical safety and information requirements for a variety of Integrated Enabling Services (IMS) programs primarily the Industrial Hygiene, Waste Management, Fire Protection, Air Quality, Emergency Management, Environmental Monitoring and Pollution Prevention programs. The principal program tool is the Chemical Information System (CIS). The system contains two key elements: the MSDS library and the chemical container-tracking database that is readily accessible to all Members of the Sandia Workforce. The primary goal of the CM Program is to ensure safe and effective chemical management at Sandia/CA. This is done by efficiently collecting and managing chemical information for our customers who include Line, regulators, DOE and ES and H programs to ensure compliance with regulations and to streamline customer business processes that require chemical information.

  4. 1983 environmental monitoring report, Sandia National Laboratories, Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Millard, G.C.; Gray, C.E.; O' Neal, B.L.

    1984-04-01

    Sandia National Laboratories (SNL) is located south of Albuquerque on Kirtland Air Force Base. Because radionuclides are potentially released from its research activities, SNL has a continuing environmental monitoring program which analyzes for cesium-137, tritium, uranium, alpha emitters, and beta emitters in water, soil, air, and vegetation. Measured radiation levels in public areas were consistent with local background in 1983. The Albuquerque population received an estimated 0.250 person-rem from airborne radioactive releases, whereas it received greater than 49,950 person-rem from naturally occurring radionuclides. 23 references, 6 figures, 15 tables.

  5. Sandia, California Tritium Research Laboratory transition and reutilization project

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, T.B. [Sandia National Lab., Albuquerque, NM (United States)

    1997-02-01

    This paper describes a project within Sandia National Laboratory to convert the shut down Tritium Research Laboratory into a facility which could be reused within the laboratory complex. In the process of decommissioning and decontaminating the facility, the laboratory was able to save substantial financial resources by transferring much existing equipment to other DOE facilities, and then expeditiously implementing a decontamination program which has resulted in the building being converted into laboratory space for new lab programs. This project of facility reuse has been a significant financial benefit to the laboratory.

  6. Mixed waste landfill corrective measures study final report Sandia National Laboratories, Albuquerque, New Mexico.

    Energy Technology Data Exchange (ETDEWEB)

    Peace, Gerald (Jerry) L.; Goering, Timothy James (GRAM, Inc., Albuquerque, NM)

    2004-03-01

    The Mixed Waste Landfill occupies 2.6 acres in the north-central portion of Technical Area 3 at Sandia National Laboratories, Albuquerque, New Mexico. The landfill accepted low-level radioactive and mixed waste from March 1959 to December 1988. This report represents the Corrective Measures Study that has been conducted for the Mixed Waste Landfill. The purpose of the study was to identify, develop, and evaluate corrective measures alternatives and recommend the corrective measure(s) to be taken at the site. Based upon detailed evaluation and risk assessment using guidance provided by the U.S. Environmental Protection Agency and the New Mexico Environment Department, the U.S. Department of Energy and Sandia National Laboratories recommend that a vegetative soil cover be deployed as the preferred corrective measure for the Mixed Waste Landfill. The cover would be of sufficient thickness to store precipitation, minimize infiltration and deep percolation, support a healthy vegetative community, and perform with minimal maintenance by emulating the natural analogue ecosystem. There would be no intrusive remedial activities at the site and therefore no potential for exposure to the waste. This alternative poses minimal risk to site workers implementing institutional controls associated with long-term environmental monitoring as well as routine maintenance and surveillance of the site.

  7. Microelectronics-embedded channel bridging and signal regeneration of injured spinal cords

    Institute of Scientific and Technical Information of China (English)

    Zhigong Wang; Xiaosong Gu; Xiaoying Lü; Zhenglin Jiang; Wenyuan Li; Guangming Lü; Yufeng Wang; Xiaoyan Shen; Xintai Zhao; Huiling Wang; Zhenyu Zhang; Hongmei Shen; Yang Wu; Weixing Shen; Jingyang Zhang; Dong Chen; Xiaoyi Mao; Huaxiang Shen

    2009-01-01

    Due to the difficulty in spinal cord regeneration with biological methods, the microelectronic neural bridge, a new concept based on microelectronic technology, is presented. The microelectronic system has been realized in the forms of hybrid and integrated circuits. The integrated circuits for neural signal detection, stimulation, and regeneration are realized in a CMOS process. In animal experiments with 100 toads, 48 rats, and 3 rabbits, nerve signals have been successfully detected from spinal cords and sciatic nerves, and functional electrical stimulation has been carried out for spinal cords and sciatic nerves. When the microelectronic system is bridged between the controlling and stimulated nerve, the relevant motion of legs and nerve signal waveforms, which are stimulated by the evoked or spontaneous nerve signal through such a system, have been observed. Therefore, the feasibility of the presented method was demonstrated.

  8. The Electrical Engineering Curriculum at the Technical University of Denmark - Options in Microelectronics

    DEFF Research Database (Denmark)

    Bruun, Erik; Nielsen, Lars Drud

    1997-01-01

    This paper describes the modular structure of the engineering curriculum at the Technical University of Denmark. The basic requirements for an electrical engineering curriculum are presented and different possibilities for specialization in microelectronics and integrated circuit design are outli......This paper describes the modular structure of the engineering curriculum at the Technical University of Denmark. The basic requirements for an electrical engineering curriculum are presented and different possibilities for specialization in microelectronics and integrated circuit design...

  9. Sub-Shot Noise Power Source for Microelectronics

    Science.gov (United States)

    Strekalov, Dmitry V.; Yu, Nan; Mansour, Kamjou

    2011-01-01

    Low-current, high-impedance microelectronic devices can be affected by electric current shot noise more than they are affected by Nyquist noise, even at room temperature. An approach to implementing a sub-shot noise current source for powering such devices is based on direct conversion of amplitude-squeezed light to photocurrent. The phenomenon of optical squeezing allows for the optical measurements below the fundamental shot noise limit, which would be impossible in the domain of classical optics. This becomes possible by affecting the statistical properties of photons in an optical mode, which can be considered as a case of information encoding. Once encoded, the information describing the photon (or any other elementary excitations) statistics can be also transmitted. In fact, it is such information transduction from optics to an electronics circuit, via photoelectric effect, that has allowed the observation of the optical squeezing. It is very difficult, if not technically impossible, to directly measure the statistical distribution of optical photons except at extremely low light level. The photoelectric current, on the other hand, can be easily analyzed using RF spectrum analyzers. Once it was observed that the photocurrent noise generated by a tested light source in question is below the shot noise limit (e.g. produced by a coherent light beam), it was concluded that the light source in question possess the property of amplitude squeezing. The main novelty of this technology is to turn this well-known information transduction approach around. Instead of studying the statistical property of an optical mode by measuring the photoelectron statistics, an amplitude-squeezed light source and a high-efficiency linear photodiode are used to generate photocurrent with sub-Poissonian electron statistics. By powering microelectronic devices with this current source, their performance can be improved, especially their noise parameters. Therefore, a room-temperature sub

  10. Multi-robots to micro-surgery: Selected robotic applications at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Bennett, P.C. [Sandia National Labs., Albuquerque, NM (United States). Intelligent Systems and Robotics Center

    1996-11-01

    The Intelligent Systems and Robotics Center (ISRC) at Sandia National Laboratories is a multi-program organization, pursuing research, development and applications in a wide range of field. Activities range from large-scale applications such as nuclear facility dismantlement for the US Department of Energy (DOE), to aircraft inspection and refurbishment, to automated script and program generation for robotic manufacturing and assembly, to miniature robotic devices and sensors for remote sensing and micro-surgery. This paper describes six activities in the large and small scale that are underway and either nearing technology transfer stage or seeking industrial partners to continue application development. The topics of the applications include multiple arm coordination for intuitively maneuvering large, ungainly work pieces; simulation, analysis and graphical training capability for CP-5 research reactor dismantlement; miniature robots with volumes of 16 cubic centimeters and less developed for inspection and sensor deployment; and biomedical sensors to enhance automated prosthetic device production and fill laparoscopic surgery information gap.

  11. Dynamic context discrimination : psychological evidence for the Sandia Cognitive Framework.

    Energy Technology Data Exchange (ETDEWEB)

    Speed, Ann Elizabeth

    2004-09-01

    Human behavior is a function of an iterative interaction between the stimulus environment and past experience. It is not simply a matter of the current stimulus environment activating the appropriate experience or rule from memory (e.g., if it is dark and I hear a strange noise outside, then I turn on the outside lights and investigate). Rather, it is a dynamic process that takes into account not only things one would generally do in a given situation, but things that have recently become known (e.g., there have recently been coyotes seen in the area and one is known to be rabid), as well as other immediate environmental characteristics (e.g., it is snowing outside, I know my dog is outside, I know the police are already outside, etc.). All of these factors combine to inform me of the most appropriate behavior for the situation. If it were the case that humans had a rule for every possible contingency, the amount of storage that would be required to enable us to fluidly deal with most situations we encounter would rapidly become biologically untenable. We can all deal with contingencies like the one above with fairly little effort, but if it isn't based on rules, what is it based on? The assertion of the Cognitive Systems program at Sandia for the past 5 years is that at the heart of this ability to effectively navigate the world is an ability to discriminate between different contexts (i.e., Dynamic Context Discrimination, or DCD). While this assertion in and of itself might not seem earthshaking, it is compelling that this ability and its components show up in a wide variety of paradigms across different subdisciplines in psychology. We begin by outlining, at a high functional level, the basic ideas of DCD. We then provide evidence from several different literatures and paradigms that support our assertion that DCD is a core aspect of cognitive functioning. Finally, we discuss DCD and the computational model that we have developed as an instantiation of DCD

  12. Molybdenum-99 Isotope Production Preparation at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Carson, S.D.; Longley, S.W.; McDonald, M.J.; Parma, E.J.; Vernon, M.E.

    1998-10-07

    `Q&c M. J. McDonald, S. D. Carson, S. W. Longley, E. J. Parma, M. E. Vern `~ I@ .,., Sandia National Laboratories*, P. .0. Box 5800, Albuquerque, NM, 8 W? 1$ tl?;:q `f. (3 . 8 /'~ Abstract This report was prepared as an account of work sponsored byanagency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, make any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government or any agency thereof. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government or any agency thereof. loading on the Cintichem targets. These tests were designed to gain process knowledge prior to processing an irradiated target. The chemical separation tests were performed in a fime hood During cold testing, several tests were performed on individual components of the process to complete, a series of `hot' tests was designed to process irradiated targets. These were designed to optimize the process, identify problems prior to processing higher inventory targets, and to the shielded containment box (SCB). Table 1 is a summary of the tests performed prior to the Test Target Power Post irradiation Total inventory 99M0 inventory (kW)/ Irradiation decay (hrs) (TBq*) /decay (TBq)/decay Time (hrs) inventory (TBq) inventory(TBq) in the processing boxes as color comparisons. Product quality control testing was conducted for all the tests and the results were compared to The production process generates a high activity

  13. Piezoelectric-nanowire-enabled power source for driving wireless microelectronics.

    Science.gov (United States)

    Xu, Sheng; Hansen, Benjamin J; Wang, Zhong Lin

    2010-10-19

    Harvesting energy from irregular/random mechanical actions in variable and uncontrollable environments is an effective approach for powering wireless mobile electronics to meet a wide range of applications in our daily life. Piezoelectric nanowires are robust and can be stimulated by tiny physical motions/disturbances over a range of frequencies. Here, we demonstrate the first chemical epitaxial growth of PbZr(x)Ti(1-x)O(3) (PZT) nanowire arrays at 230 °C and their application as high-output energy converters. The nanogenerators fabricated using a single array of PZT nanowires produce a peak output voltage of ~0.7 V, current density of 4 μA cm(-2) and an average power density of 2.8 mW cm(-3). The alternating current output of the nanogenerator is rectified, and the harvested energy is stored and later used to light up a commercial laser diode. This work demonstrates the feasibility of using nanogenerators for powering mobile and even personal microelectronics.

  14. Electromigration of intergranular voids in metal films for microelectronic interconnects

    CERN Document Server

    Averbuch, A; Ravve, I

    2003-01-01

    Voids and cracks often occur in the interconnect lines of microelectronic devices. They increase the resistance of the circuits and may even lead to a fatal failure. Voids may occur inside a single grain, but often they appear on the boundary between two grains. In this work, we model and analyze numerically the migration and evolution of an intergranular void subjected to surface diffusion forces and external voltage applied to the interconnect. The grain-void interface is considered one-dimensional, and the physical formulation of the electromigration and diffusion model results in two coupled fourth-order one-dimensional time-dependent PDEs. The boundary conditions are specified at the triple points, which are common to both neighboring grains and the void. The solution of these equations uses a finite difference scheme in space and a Runge-Kutta integration scheme in time, and is also coupled to the solution of a static Laplace equation describing the voltage distribution throughout the grain. Since the v...

  15. Wireless link and microelectronics design for retinal prostheses

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Wentai [Univ. of California, Santa Cruz, CA (United States)

    2012-02-29

    This project focuses on delivering power and data to the artificial retinal implant inside the eye and the implant microstimulator electronics which delivers the current pulses to stimulate the retinal layer to elicit visual perception. Since the use of invasive means such as tethering wires to transmit power and data results in discomfort to the patients which could eventually cause infection due to the abrasion caused by the wire and contact of the internals of the eye to the external environment, a completely wireless approach is used to transfer both power and data. Power is required inside the eye for the microelectronic implant which uses a dual voltage supply scheme (positive and negative) to deliver biphasic (anodic and cathodic) current pulses. Data in the form of digital bits from the data transmitter external to the eye, carries information about the amplitude, phase width, interphase delay, stimulation sequence for each implant electrode. The data receiver unit decodes the digital stream and the microstimulator unit generates the appropriate current stimuli. Since the external unit consisting of the power transmitter can experience coupling a variation with the power receiver due to the patient’s movements, a closed loop approach is used which varies the transmitted power dynamically to automatically compensate for such movements. This report presents the salient features of this research activities and results.

  16. Research on the Use of Robotics in Hazardous Environments at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Kwok, Kwan S.

    1999-05-04

    Many hazardous material handling needs exist in remote unstructured environments. Currently these operations are accomplished using personnel in direct contact with the hazards. A safe and cost effective alternative to this approach is the use of intelligent robotic systems for safe handling, packaging, transport, and even excavation of hazardous materials. The Intelligent Systems and Robotics Center of Sandia National Laboratories has developed and deployed robotic technologies for use in hazardous environments, three of which have been deployed in DOE production facilities for handling of special nuclear materials. Other systems are currently under development for packaging special nuclear materials. This paper presents an overview of the research activities, including five delivered systems, at %ndia National Laboratories on the use of robotics in hazardous environments.

  17. Conformal coating value/risk assessment for Sandia satellite programs.

    Energy Technology Data Exchange (ETDEWEB)

    Russick, Edward Mark; Thayer, Gayle Echo

    2008-03-01

    Conformal coatings are used in space applications on printed circuit board (PCB) assemblies primarily as a protective barrier against environmental contaminants. Such coatings have been used at Sandia for decades in satellite applications including the GPS satellite program. Recently, the value of conformal coating has been questioned because it is time consuming (requiring a 5-6 week schedule allowance) and delays due to difficulty of repairs and rework performed afterward are troublesome. In an effort to find opportunities where assembly time can be reduced, a review of the literature as well as discussions with satellite engineers both within and external to Sandia regarding the value of conformal coating was performed. Several sources on the value of conformal coating, the functions it performs, and on whether coatings are necessary and should be used at all were found, though nearly all were based on anecdotal information. The first section of this report, titled 'Conformal Coating for Space Applications', summarizes the results of an initial risk-value assessment of the conformal coating process for Sandia satellite programs based on information gathered. In the process of collecting information to perform the assessment, it was necessary to obtain a comprehensive understanding of the entire satellite box assembly process. A production time-line was constructed and is presented in the second section of this report, titled 'Satellite Box Assembly', specifically to identify potential sources of time delays, manufacturing issues, and component failures related to the conformal coating process in relation to the box assembly. The time-line also allows for identification of production issues that were anecdotally attributed to the conformal coating but actually were associated with other production steps in the box assembly process. It was constructed largely in consultation with GPS program engineers with empirical knowledge of times required

  18. Calendar Year 2009 Annual Site Environmental Report for Sandia National Laboratories, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, Karen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bailey-White, Brenda [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bonaguidi, Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Brown, Mendy [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Byrd, Caroline [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Cabble, Kevin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Castillo, Dave [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Coplen, Amy [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Curran, Kelsey [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Deola, Regina [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Duran, Leroy [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Eckstein, Joanna [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Evelo, Stacie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Fitzgerald, Tanja [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); French, Chris [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gerard, Morgan [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gonzales, Linda [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gorman, Susan [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jackson, Timothy [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jarry, Jeff [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jones, Adrian [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Lauffer, Franz [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mauser, Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mayeux, Lucie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); McCord, Samuel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Miller, Mark [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Oborny, Stephanie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Perini, Robin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Puissant, Pamela [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Reiser, Anita [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Roma, Charles [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Salinas, Stephanie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Skelly, Michael [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ullrich, Rebecca [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wagner, Katrina [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wrons, Ralph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2010-09-30

    Sandia National Laboratories, New Mexico (SNL/NM) is a government-owned/contractor operated facility. Sandia Corporation (Sandia), a wholly owned subsidiary of Lockheed Martin Corporation (LMC), manages and operates the laboratory for the U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA). The DOE/NNSA, Sandia Site O ffice (SSO) administers the contract and oversees contractor operations at the site. This annual report summarizes data and the compliance status of Sandia Corporation’s environmental protection and monitoring programs through December 31, 2009. Major environmental programs include air quality, water quality, groundwater protection, terrestrial surveillance, waste management, pollution prevention (P2), environmental restoration (ER), oil and chemical spill prevention, and implementation of the National Environmental Policy Act (NEPA). Environmental monitoring and surveillance programs are required by DOE Order 450.1A, Environmental Protection Program (DOE 2008a) and DOE Manual 231.1-1A, Environment, Safety, and Health Reporting (DOE 2007).

  19. Annual Site Environmental Report Sandia National Laboratories, Albuquerque, New Mexico, Calendar year 2007

    Energy Technology Data Exchange (ETDEWEB)

    Agogino, Karen [National Nuclear Security Administration (NNSA), Washington, DC (United States); Sanchez, Rebecca [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2008-09-30

    Sandia National Laboratories, New Mexico (SNL/NM) is a government-owned/contractor-operated facility. Sandia Corporation (Sandia), a wholly owned subsidiary of Lockheed Martin Corporation, manages and operates the laboratory for the U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA). The DOE/NNSA Sandia Site Office (SSO) administers the contract and oversees contractor operations at the site. This annual report summarizes data and the compliance status of Sandia Corporation’s environmental protection and monitoring programs through December 31, 2007. Major environmental programs include air quality, water quality, groundwater protection, terrestrial surveillance, waste management, pollution prevention (P2), environmental restoration (ER), oil and chemical spill prevention, and implementation of the National Environmental Policy Act (NEPA). Environmental monitoring and surveillance programs are required by DOE Order 450.1, Environmental Protection Program (DOE 2007a) and DOE Manual 231.1-1A, Environment, Safety, and Health Reporting (DOE 2007).

  20. 1991 Environmental monitoring report Sandia National Laboratories, Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Culp, T.; Cox, W.; Hwang, S.; Jones, A.; Longley, S.; Parsons, A.; Wolff, T.; Fish, J.; Ward, S.

    1992-11-01

    This 1991 report contains monitoring data from routine radiological and nonradiological environmental surveillance activities. Summaries of significant environmental compliance programs in progress such as National Environmental Policy Act (NEPA) documentation, environmental permits, environmental restoration (ER), and various waste management programs for Sandia National Laboratories in Albuquerque (SNL, Albuquerque) are included. The maximum offsite dose impact was calculated to be 1.3 {times} 10{sup {minus}3} mrem. The total population within a 50-mile radius of SNL, Albuquerque, received a collective dose of 0.53 person-rem during 1991 from SNL, Albuquerque, operations. As in the previous year, the 1991 operations at SNL, Albuquerque, had no discernible impact on the general public or on the environment.

  1. 1990 Environmental Monitoring Report, Sandia National Laboratories, Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, S.; Yeager, G.; Wolff, T.; Parsons, A.; Dionne, D.; Massey, C.; Schwartz, B.; Fish, J.; Thompson, D. (Sandia National Labs., Albuquerque, NM (United States)); Goodrich, M. (GRAM, Inc., Albuquerque, NM (United States))

    1991-05-01

    This 1990 report contains monitoring data from routine radiological and nonradiological environmental surveillance activities. Summaries of significant environmental compliance programs in progress such as National Environmental Policy Act (NEPA) documentation, environmental permits, environmental restoration, and various waste management programs for Sandia National Laboratories in Albuquerque (SNL, Albuquerque) are included. The maximum offsite dose impact was calculated to be 2.0 {times} 10{sup {minus}3} mrem. The total 50-mile population received a collective dose of 0.82 person-rem during 1990 from SNL, Albuquerque, operations. As in the previous year, the 1990 SNL operations had no adverse impact on the general public or on the environment. This report is prepared for the US Department of Energy in compliance with DOE Order 5400.1. 97 refs., 30 figs., 137 tabs.

  2. Epidemiologic surveillance. Annual report for Sandia National Laboratories 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-31

    Epidemiologic surveillance at DOE facilities consists of regular and systematic collection, analysis, and interpretation of data on absences due to illness and injury in the work force. Its purpose is to provide an early warning system for health problems occurring among employees at participating sites. In this annual report, 1994 morbidity data for the Sandia National Laboratories are summarized. These analyses focus on absences of 5 or more consecutive workdays occurring among workers aged 15-76 years. They are arranged in five sets of tables that present: (1) the distribution of the labor force by occupational category and pay status; (2) the absences per person, diagnoses per absence, and diagnosis rates for the whole work force; (3) diagnosis rates by type of disease or injury; (4) diagnosis rates by occupational category; and (5) relative risks for specific types of disease or injury by occupational category.

  3. Sandia National Laboratories shock thermodynamics applied research (STAR) facility

    Energy Technology Data Exchange (ETDEWEB)

    Asay, J.R.

    1981-08-01

    The Sandia National Laboratories Shock Thermodynamics Applied Research (STAR) Facility has recently consolidated three different guns and a variety of instrumentation capabilities into a single location. The guns available at the facility consist of a single-stage light gas gun, a single-stage propellant gun and a two-stage light gas gun, which cover a velocity range from 15 m/s to 8 km/s. Instrumentation available at the facility includes optical and microwave interferometry, time-resolved holography, fast x-radiography, framing and streak photography, fast multi-wavelength pyrometry, piezoelectric and piezoresistive gauges and computer data reduction. This report discusses the guns and instrumentation available at the facility and selected recent applications.

  4. Tritium monitoring at the Sandia Tritium Research Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Devlin, T.K.

    1978-10-01

    Sandia Laboratories at Livermore, California, is presently beginning operation of a Tritium Research Laboratory (TRL). The laboratory incorporates containment and cleanup facilities such that any unscheduled tritium release is captured rather than vented to the atmosphere. A sophisticated tritium monitoring system is in use at the TRL to protect operating personnel and the environment, as well as ensure the safe and effective operation of the TRL decontamination systems. Each monitoring system has, in addition to a local display, a display in a centralized control room which, when coupled room which, when coupled with the TRL control computer, automatically provides an immediate assessment of the status of the entire facility. The computer controls a complex alarm array status of the entire facility. The computer controls a complex alarm array and integrates and records all operational and unscheduled tritium releases.

  5. 1989 Environmental monitoring report, Sandia National Laboratories, Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, S.; Chavez, G.; Phelan, J.; Parsons, A.; Yeager, G.; Dionne, D.; Schwartz, B.; Wolff, T.; Fish, J.; Gray, C.; Thompson, D.

    1990-05-01

    This 1989 report contains monitoring data from routine radiological and nonradiological environmental surveillance activities. Summaries of significant environmental compliance programs in progress such as National Environmental Policy Act documentation, environmental permits, environmental restoration, and various waste management programs for Sandia National Laboratories in Albuquerque (SNL, Albuquerque) are included. The maximum offsite dose impact was calculated to be 8.8 {times} 10{sup {minus}4} mrem. The total Albuquerque population received a collective dose of 0.097 person-rem during 1989 from SNL, Albuquerque, operations. As in the previous year, SNL, Albuquerque, operations in 1989 had no adverse impact on the general public or on the environment. 46 refs., 20 figs., 31 tabs.

  6. Sandia National Laboratories Internal Dosimetry Technical Basis Manual (Rev 4)

    Energy Technology Data Exchange (ETDEWEB)

    Goke, Sarah Hayes [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Elliott, Nathan Ryan [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-09-01

    The Sandia National Laboratories’ Internal Dosimetry Technical Basis Manual is intended to provide extended technical discussion and justification of the internal dosimetry program at SNL. It serves to record the approach to evaluating internal doses from radiobioassay data, and where appropriate, from workplace monitoring data per the Department of Energy Internal Dosimetry Program Guide DOE G 441.1C. The discussion contained herein is directed primarily to current and future SNL internal dosimetrists. In an effort to conserve space in the TBM and avoid duplication, it contains numerous references providing an entry point into the internal dosimetry literature relevant to this program. The TBM is not intended to act as a policy or procedure statement, but will supplement the information normally found in procedures or policy documents. The internal dosimetry program outlined in this manual is intended to meet the requirements of Federal Rule 10CFR835 for monitoring the workplace and for assessing internal radiation doses to workers.

  7. Organizational cultural assessment of the Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    1991-05-01

    An Organizational Cultural Assessment (OCA) was performed at the Sandia National Laboratories (SNL) by administering an Organizational Culture Survey (OCS) that queried employees on the subjects of organizational culture, various aspects of communications, employee commitment, work group cohesion, coordination of work, environmental concerns, hazardous nature of work, safety, and overall job satisfaction. The purpose of the OCS is to measure in a quantitative and objective way the values, attitudes, and beliefs of the individuals working within the organization. The OCS administration at SNL was the fifth to occur at a DOE facility. The sample was randomly selected from each Vice Presidency group, the largest organizational unit at SNL. Scores and significance are discussed and statistically significant differences between groups are identified and discussed.

  8. Sandia Lightning Simulation Facility Building 888. Hazards assessment document

    Energy Technology Data Exchange (ETDEWEB)

    Banda, Z.; Barnett, B.

    1994-10-01

    The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Sandia Lightning Simulation Facility, Building 888. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 23 meters. The highest emergency classification is a Site Area Emergency. The Emergency Planning Zone is 65 meters.

  9. Sandia Administrative Micrographics Facility, Building 802: Hazards assessment document

    Energy Technology Data Exchange (ETDEWEB)

    Swihart, A.

    1994-12-01

    The Department of Energy Order 5500.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the Sandia Administrative Micrographics Facility, Building 802. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 33 meters. The highest emergency classification is a Site Area Emergency. The Emergency Planning Zone is 75 meters.

  10. Sandia National Laboratories' new high level acoustic test facility

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, J. D.; Hendrick, D. M.

    1989-01-01

    A high intensity acoustic test facility has been designed and is under construction at Sandia National Laboratories in Albuquerque, NM. The chamber is designed to provide an acoustic environment of 154dB (re 20 {mu}Pa) overall sound pressure level over the bandwidth of 50 Hz to 10,000 Hz. The chamber has a volume of 16,000 cubic feet with interior dimensions of 21.6 ft {times} 24.6 ft {times} 30 ft. The construction of the chamber should be complete by the summer of 1990. This paper discusses the design goals and constraints of the facility. The construction characteristics are discussed in detail, as are the acoustic performance design characteristics. The authors hope that this work will help others in designing acoustic chambers. 12 refs., 6 figs.

  11. 1989 Environmental monitoring report, Sandia National Laboratories, Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, S.; Chavez, G.; Phelan, J.; Parsons, A.; Yeager, G.; Dionne, D.; Schwartz, B.; Wolff, T.; Fish, J.; Gray, C.; Thompson, D.

    1990-05-01

    This 1989 report contains monitoring data from routine radiological and nonradiological environmental surveillance activities. Summaries of significant environmental compliance programs in progress such as National Environmental Policy Act documentation, environmental permits, environmental restoration, and various waste management programs for Sandia National Laboratories in Albuquerque (SNL, Albuquerque) are included. The maximum offsite dose impact was calculated to be 8.8 {times} 10{sup {minus}4} mrem. The total Albuquerque population received a collective dose of 0.097 person-rem during 1989 from SNL, Albuquerque, operations. As in the previous year, SNL, Albuquerque, operations in 1989 had no adverse impact on the general public or on the environment. 46 refs., 20 figs., 31 tabs.

  12. Baseline ecological footprint of Sandia National Laboratories, New Mexico.

    Energy Technology Data Exchange (ETDEWEB)

    Coplen, Amy K.; Mizner, Jack Harry,; Ubechel, Norion M.

    2009-01-01

    The Ecological Footprint Model is a mechanism for measuring the environmental effects of operations at Sandia National Laboratories in Albuquerque, New Mexico (SNL/NM). This analysis quantifies environmental impact associated with energy use, transportation, waste, land use, and water consumption at SNL/NM for fiscal year 2005 (FY05). Since SNL/NMs total ecological footprint (96,434 gha) is greater than the waste absorption capacity of its landholdings (338 gha), it created an ecological deficit of 96,096 gha. This deficit is equal to 886,470lha, or about 3,423 square miles of Pinyon-Juniper woodlands and desert grassland. 89% of the ecological footprint can be attributed to energy use, indicating that in order to mitigate environmental impact, efforts should be focused on energy efficiency, energy reduction, and the incorporation of additional renewable energy alternatives at SNL/NM.

  13. Assessment and Assurance of Microelectronics Packaging Technology of Microelectromechanical Systems (MEMS)

    Science.gov (United States)

    Ramesham, Rajeshuni

    2000-01-01

    Microelectromechanical systems (MEMS) have shown a significant promise in the last decade for a variety of applications such as air-bag, pressure sensors, accelerometer, microgyro, etc. Standard semiconductor microelectronics packaging needs the integrated circuits to be protected from the harsh environment, and provide electrical communication with the other parts of the circuit, facilitate thermal dissipation efficiently, and impart mechanical strength to the silicon die. Microelectronics packaging involves wafer dicing, bonding, lead attachment, encapsulation to protect from the environment, electrical integrity, and package leak tests to assure the packaging technology. In the case of MEMS the microstructures (active elements) often interfaces with the hostile environment where packaging leak tests and testing of such devices using chemical and mechanical parameters will be very difficult and expensive. Packaging of MEMS is significantly complex as they serve to protect from the environment and microstructures interact with the same environment to measure or affect the desired physical or chemical parameters. The most of the silicon circuitry is sensitive to temperature, moisture, magnetic field, light, and electromagnetic interference. The package must then protect the on-board silicon circuitry while simultaneously exposing the microsensor to the effect it 'measures to assure the MEMS technology by lowering the risk to zero. MEMS technology has a major application in developing a microspacecraft for space systems provided assurance of MEMS technology is sufficiently addressed nondestructively. This technology would eventually miniaturize many of the components of the spacecraft to reach the NASA's safety and mission assurance goal by building faster, cheaper, better, smaller spacecraft to explore the space more effectively by teaming-up with the other NASA centers using the limited resources available. This paper discusses the latest developments in the MEMS

  14. GeNeDA: An Open-Source Workflow for Design Automation of Gene Regulatory Networks Inspired from Microelectronics.

    Science.gov (United States)

    Madec, Morgan; Pecheux, François; Gendrault, Yves; Rosati, Elise; Lallement, Christophe; Haiech, Jacques

    2016-10-01

    The topic of this article is the development of an open-source automated design framework for synthetic biology, specifically for the design of artificial gene regulatory networks based on a digital approach. In opposition to other tools, GeNeDA is an open-source online software based on existing tools used in microelectronics that have proven their efficiency over the last 30 years. The complete framework is composed of a computation core directly adapted from an Electronic Design Automation tool, input and output interfaces, a library of elementary parts that can be achieved with gene regulatory networks, and an interface with an electrical circuit simulator. Each of these modules is an extension of microelectronics tools and concepts: ODIN II, ABC, the Verilog language, SPICE simulator, and SystemC-AMS. GeNeDA is first validated on a benchmark of several combinatorial circuits. The results highlight the importance of the part library. Then, this framework is used for the design of a sequential circuit including a biological state machine.

  15. Reproductive Hazards Still Persist in the Microelectronics Industry: Increased Risk of Spontaneous Abortion and Menstrual Aberration among Female Workers in the Microelectronics Industry in South Korea

    Science.gov (United States)

    Kim, Inah; Kim, Myoung-Hee; Lim, Sinye

    2015-01-01

    Objectives Despite the global expansion of supply chains and changes to the production process, few studies since the mid-1990s and 2000s have examined reproductive risks of the microelectronics industry; we examined the reproductive risks among female microelectronics workers in South Korea. Methods Based on claim data from the National Health Insurance (2008–2012), we estimated age-specific rates of spontaneous abortion (SAB) and menstrual aberration (MA) among women aged 20 to 39 years. We compared data between microelectronics workers and three different control groups: economically inactive women, the working population as a whole, and workers employed in the bank industry. For an effect measure, age-stratified relative risks (RRs) were estimated. Results Female workers in the microelectronics industry showed significantly higher risk for SAB and MA compared to control groups. The RRs for SAB with reference to economically inactive women, working population, and bank workers in their twenties were 1.57, 1.40, and 1.37, respectively, and the RRs for MA among females in their twenties were 1.54, 1.38, and 1.48, respectively. For women in their thirties, RRs for SAB were 1.58, 1.67, and 1.13, and those for MA were 1.25, 1.35, and 1.23 compared to the three control populations, respectively. All RRs were statistically significant at a level of 0.05, except for the SAB case comparison with bank workers in their thirties. Conclusions Despite technical innovations and health and safety measures, female workers in microelectronics industry in South Korea have high rates of SAB and MA, suggesting continued exposure to reproductive hazards. Further etiologic studies based on primary data collection and careful surveillance are required to confirm these results. PMID:25938673

  16. Reproductive Hazards Still Persist in the Microelectronics Industry: Increased Risk of Spontaneous Abortion and Menstrual Aberration among Female Workers in the Microelectronics Industry in South Korea.

    Directory of Open Access Journals (Sweden)

    Inah Kim

    Full Text Available Despite the global expansion of supply chains and changes to the production process, few studies since the mid-1990 s and 2000s have examined reproductive risks of the microelectronics industry; we examined the reproductive risks among female microelectronics workers in South Korea.Based on claim data from the National Health Insurance (2008-2012, we estimated age-specific rates of spontaneous abortion (SAB and menstrual aberration (MA among women aged 20 to 39 years. We compared data between microelectronics workers and three different control groups: economically inactive women, the working population as a whole, and workers employed in the bank industry. For an effect measure, age-stratified relative risks (RRs were estimated.Female workers in the microelectronics industry showed significantly higher risk for SAB and MA compared to control groups. The RRs for SAB with reference to economically inactive women, working population, and bank workers in their twenties were 1.57, 1.40, and 1.37, respectively, and the RRs for MA among females in their twenties were 1.54, 1.38, and 1.48, respectively. For women in their thirties, RRs for SAB were 1.58, 1.67, and 1.13, and those for MA were 1.25, 1.35, and 1.23 compared to the three control populations, respectively. All RRs were statistically significant at a level of 0.05, except for the SAB case comparison with bank workers in their thirties.Despite technical innovations and health and safety measures, female workers in microelectronics industry in South Korea have high rates of SAB and MA, suggesting continued exposure to reproductive hazards. Further etiologic studies based on primary data collection and careful surveillance are required to confirm these results.

  17. Unified parallel C and the computing needs of Sandia National Laboratories.

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Jonathan Leighton; Wen, Zhaofang

    2004-09-01

    As Sandia looks toward petaflops computing and other advanced architectures, it is necessary to provide a programming environment that can exploit this additional computing power while supporting reasonable development time for applications. Thus, they evaluate the Partitioned Global Address Space (PGAS) programming model as implemented in Unified Parallel C (UPC) for its applicability. They report on their experiences in implementing sorting and minimum spanning tree algorithms on a test system, a Cray T3e, with UPC support. They describe several macros that could serve as language extensions and several building-block operations that could serve as a foundation for a PGAS programming library. They analyze the limitations of the UPC implementation available on the test system, and suggest improvements necessary before UPC can be used in a production environment.

  18. Impactful times memories of 60 years of shock wave research at Sandia National Laboratories

    CERN Document Server

    Asay, James R; Lawrence, R Jeffery; Sweeney, Mary Ann

    2017-01-01

    This book presents a history of shock compression science, including development of experimental, material modeling, and hydrodynamics code technologies over the past six decades at Sandia National Laboratories. The book is organized into a discussion of major accomplishments by decade with over 900 references, followed by a unique collection of 45 personal recollections detailing the trials, tribulations, and successes of building a world-class organization in the field. It explains some of the challenges researchers faced and the gratification they experienced when a discovery was made. Several visionary researchers made pioneering advances that integrated these three technologies into a cohesive capability to solve complex scientific and engineering problems. What approaches worked, which ones did not, and the applications of the research are described. Notable applications include the turret explosion aboard the USS Iowa and the Shoemaker-Levy comet impact on Jupiter. The personal anecdotes and recollec...

  19. Performance Evaluation of Management Environment in Microelectronics Enterprise

    Directory of Open Access Journals (Sweden)

    Hui-ying Gao

    2013-05-01

    Full Text Available For the microelectronics manufacturing industries that have uncertain demand, high volume cost and Oligarchs characteristics, we often discuss the possibility of competitors on the capacity of strategy. First of all we use the industry data to analysis the manufacturing cost, demand and the historical situation of the revenue and we also discuss the influence about the uncertain demand and high volume cost to the industrial structure. Secondly, it put the individual manufacturer not considering the capacity decision of the competitor as the premise and put revenue as the performance target for capacity expansion to construct the mathematical optimization model of the productivity level under the uncertain demand. And the productivity level is called the micro capacity. The manufacturer based on competition and the levels of microscopic production can consider using the radical strategy or still upholding the microscopic optimal capacity, and then put forward a game model to analysis the expected profits of the leaders and the followers who have take the two strategies. Besides, we can use the industrial data to calculate and then get the equilibrium. At last we can calculate the conclusion that for the manufacturers of monopoly industry when they faced with the different marginal profit, different demand variation and hyperbaric capacity amortization cost, the leading manufacturers can use radical production strategy. On the one hand, they can improve the profits, on the other hand they can also compress the profit that was gotten by following the manufacturers. Therefore, the capacity expansion decision can be used as the means of competition for the leading manufacturers.

  20. Isotropic copper-invar alloys for microelectronics packaging

    Science.gov (United States)

    Cottle, Rand Duprez

    The recent trend in microelectronics packaging toward surface mounted devices (SMD) has created a need for new types of materials that possess low thermal expansion and high electrical and thermal conductivity. Laminates that combine the high thermal and electrical conductivity of copper with the low thermal expansion of Invar, know as CuInvarCu or CIC, are widely use as core constraining materials in printed wire boards where SMDs are to be employed. CIC is highly anisotropic, and there are potential problems resulting from its anisotropy. An isotropic CuInvar alloy would be of great interest for a variety of applications. In suitable Cu-Fe-Ni alloys, a copper-rich solid solution equilibrates with an Invar-rich solid solution; casting such alloys invariably produces Invar-rich dendrites in a copper-rich solid solution. Casting followed by suitable heat treatments can produce two-phase alloys that combine the properties of copper and Invar. The overall composition controls the relative fractions of Invar and copper and the resulting trade-off between low thermal expansivity and electrical conductivity. Measured thermal expansivities (CTE) of CuInvar alloys follow very closely a linear rule of mixing. Electrical conductivities of as-cast specimens are quite poor due to iron and nickel contamination. Theoretical phase diagrams indicate that nearly pure copper equilibrates with an Invar-rich phase at temperatures below, roughly, 500°C. However, equilibrium compositions have been shown to take extremely, long to form, due to the very sluggish kinetics in the system. Long-term annealing was shown to improve conductivity significantly, but much greater improvements are needed to make CuInvar viable as an electrical conductive material.

  1. Uniprocessor Performance Analysis of a Representative Workload of Sandia National Laboratories' Scientific Applications.

    Energy Technology Data Exchange (ETDEWEB)

    Charles Laverty

    2005-10-01

    UNIPROCESSOR PERFORMANCE ANALYSIS OF A REPRESENTATIVE WORKLOAD OF SANDIA NATIONAL LABORATORIES' SCIENTIFIC APPLICATIONS Master of Science in Electrical Engineering New Mexico State University Las Cruces, New Mexico, 2005 Dr. Jeanine Cook, Chair Throughout the last decade computer performance analysis has become absolutely necessary to maximum performance of some workloads. Sandia National Laboratories (SNL) located in Albuquerque, New Mexico is no different in that to achieve maximum performance of large scientific, parallel workloads performance analysis is needed at the uni-processor level. A representative workload has been chosen as the basis of a computer performance study to determine optimal processor characteristics in order to better specify the next generation of supercomputers. Cube3, a finite element test problem developed at SNL is a representative workload of their scientific workloads. This workload has been studied at the uni-processor level to understand characteristics in the microarchitecture that will lead to the overall performance improvement at the multi-processor level. The goal of studying vthis workload at the uni-processor level is to build a performance prediction model that will be integrated into a multi-processor performance model which is currently being developed at SNL. Through the use of performance counters on the Itanium 2 microarchitecture, performance statistics are studied to determine bottlenecks in the microarchitecture and/or changes in the application code that will maximize performance. From source code analysis a performance degrading loop kernel was identified and through the use of compiler optimizations a performance gain of around 20% was achieved.

  2. Selected area chemical vapor deposition of thin films for conductometric microelectronic chemical sensors

    Science.gov (United States)

    Majoo, Sanjeev

    Recent advances in microelectronics and silicon processing have been exploited to fabricate miniaturized chemical sensors. Although the capability of chemical sensing technology has grown steadily, it has been outpaced by the increasing demands for more reliable, inexpensive, and selective sensors. The diversity of applications requires the deployment of different sensing materials that have rich interfacial chemistry. However, several promising sensor materials are often incompatible with silicon micromachining and their deposition requires complicated masking steps. The new approach described here is to first micromachine a generic, instrumented, conductometric, microelectronic sensor platform that is fully functional except for the front-end sensing element. This generic platform contains a thin dielectric membrane, an integrated boron-doped silicon heater, and conductance electrodes. The membrane has low thermal mass and excellent thermal isolation. A proprietary selected-area chemical vapor deposition (SACVD) process in a cold-wall reactor at low pressures was then used to achieve maskless, self-lithographic deposition of thin films. The temperature-programmable integrated microheater initiates localized thermal decomposition/reaction of suitable CVD precursors confined to a small heated area (500 mum in diameter), and this creates the active sensing element. Platinum and titania (TiOsb2) films were deposited from pyrolysis of organometallic precursors, tetrakistrifluorophosphine platinum Pt(PFsb3)sb4 and titanium tetraisopropoxide Ti(OCH(CHsb3)sb2rbrack sb4, respectively. Deposition of gold metal films from chlorotriethylphosphine gold (Csb2Hsb5)sb3PAuCl precursor was also attempted but without success. The conductance electrodes permit in situ monitoring of film growth. The as-deposited films were characterized in situ by conductance measurements and optical microscopy and ex situ by electron microscopy and spectroscopy methods. Devices equipped with

  3. Microelectronics and nanotechnology, and the fractal-like structure of information, knowledge, and science

    Science.gov (United States)

    Nutu, Catalin Silviu; Axinte, Tiberiu

    2016-12-01

    The article is centralizing and is concentrating the information from a considerable amount of papers related to the field of microelectronics and nanotechnology and also provides an approach to science and to the future evolution of science, based on the theory of the fractals. The new science of microelectronics and nanotechnology is one of the best examples of how the science of future will look like, namely at the confluence of increasingly more other sciences, where increasingly more sciences are to be added in the structure of the new science and the role of the multidisciplinary and interdisciplinary is becoming more and more important. Although not giving explicit details (e.g. specific formulas) the theory of fractals is used in the paper to explain the way of generation of new science for the specific case of microelectronics and nanotechnology, but is also used in the paper to outline a different way to approach new science and eventually to approach new sciences to come. There are mainly two motivations for the present article, namely: on the one hand, the position of the microelectronics and nanotechnologies in the fractal-like structure of science, and, on the other hand, that much of the communication, information, knowledge and science transfer, dissemination and advancement in sciences are taking place using the new technologies related to microelectronics and nanotechnologies.

  4. Design and performance of Sandia`s contactless coilgun for 50 mm projectiles

    Energy Technology Data Exchange (ETDEWEB)

    Kaye, R.J.; Cnare, E.C.; Cowan, M.; Duggin, B.W.; Lipinski, R.J.; Marder, B.M. [Sandia National Labs., Albuquerque, NM (United States); Douglas, G.M. [Rockwell Power Systems Co., Albuquerque, NM (United States); Shimp, K.J. [EG and G, Inc., Albuquerque, NM (United States)

    1991-12-31

    A multi-stage, contactless coilgun is being designed to demonstrate the applicability of this technology to accelerate nominal 50 mm (2 inch) diameter projectiles to velocities of 3 km/s. Forty stages of this design (Phase 1 coilgun) will provide a testbed for coil designs and system components while accelerating 200 to 400 gram projectiles to 1 km/s. We have successfully qualified the Phase 1 gun by operating 40 stages at half energy (10 kJ stored/stage) accelerating 340 gram, room-temperature, aluminum-armature projectiles to 406 m/s. We expect to accelerate 200 gram projectiles cooled to {minus}196{degrees}C to three times this velocity when operating at full energy. This paper describes the design and performance of the Phase 1 coilgun and includes discussion of coil development, projectile design, capacitor banks, firing system, and integration. 10 refs.

  5. The Principle of the Micro-Electronic Neural Bridge and a Prototype System Design.

    Science.gov (United States)

    Huang, Zong-Hao; Wang, Zhi-Gong; Lu, Xiao-Ying; Li, Wen-Yuan; Zhou, Yu-Xuan; Shen, Xiao-Yan; Zhao, Xin-Tai

    2016-01-01

    The micro-electronic neural bridge (MENB) aims to rebuild lost motor function of paralyzed humans by routing movement-related signals from the brain, around the damage part in the spinal cord, to the external effectors. This study focused on the prototype system design of the MENB, including the principle of the MENB, the neural signal detecting circuit and the functional electrical stimulation (FES) circuit design, and the spike detecting and sorting algorithm. In this study, we developed a novel improved amplitude threshold spike detecting method based on variable forward difference threshold for both training and bridging phase. The discrete wavelet transform (DWT), a new level feature coefficient selection method based on Lilliefors test, and the k-means clustering method based on Mahalanobis distance were used for spike sorting. A real-time online spike detecting and sorting algorithm based on DWT and Euclidean distance was also implemented for the bridging phase. Tested by the data sets available at Caltech, in the training phase, the average sensitivity, specificity, and clustering accuracies are 99.43%, 97.83%, and 95.45%, respectively. Validated by the three-fold cross-validation method, the average sensitivity, specificity, and classification accuracy are 99.43%, 97.70%, and 96.46%, respectively.

  6. Can zinc aluminate-titania composite be an alternative for alumina as microelectronic substrate?

    Science.gov (United States)

    Roshni, Satheesh Babu; Sebastian, Mailadil Thomas; Surendran, Kuzhichalil Peethambharan

    2017-01-01

    Alumina, thanks to its superior thermal and dielectric properties, has been the leading substrate over several decades, for power and microelectronics circuits. However, alumina lacks thermal stability since its temperature coefficient of resonant frequency (τf) is far from zero (‑60 ppmK‑1). The present paper explores the potentiality of a ceramic composite 0.83ZnAl2O4-0.17TiO2 (in moles, abbreviated as ZAT) substrates for electronic applications over other commercially-used alumina-based substrates and synthesized using a non-aqueous tape casting method. The present substrate has τf of + 3.9 ppmK‑1 and is a valuable addition to the group of thermo-stable substrates. The ZAT substrate shows a high thermal conductivity of 31.3 Wm‑1K‑1 (thermal conductivity of alumina is about 24.5 Wm‑1K‑1), along with promising mechanical, electrical and microwave dielectric properties comparable to that of alumina-based commercial substrates. Furthermore, the newly-developed substrate material shows exceptionally good thermal stability of dielectric constant, which cannot be met with any of the alumina-based HTCC substrates.

  7. Quality politics: an immaterial investment for companies in (micro)electronics

    Science.gov (United States)

    Bacivarov, I. C.; Lupan, R.; Robledo, C.; Bacivarov, Angelica

    2010-11-01

    With the globalization of the markets and the growth of competitiveness in the manufacturing sector, quality has become a key factor of success. Quality is particularly important for the companies which activate in the micro(electronics) field. The quality management system holds a vital place in the company's structure. Implementing such a system requires important operating costs. These costs are known as Quality Obtaining Costs (QOC) and may be considered as an investment. Planning an investment, means evaluating its return in order to see if it is profitable or not. Measuring the return of quality politics investment raise some delicate problems. We may calculate some aspects of the return of investment by measuring the shape of non-quality costs. An eventual decrease of these costs could be synonym with a profitable investment. But the advantages of good quality politics cannot be measured only by taking into consideration the non-quality costs (even if they include direct and indirect costs). There are also intangible advantages (like mark image, competences, polyvalence, client's satisfaction...) that derive from quality approaches. How to evaluate this type of consequences / advantages? The idea developed in this article is to considerate the quality politics like un immaterial/intelligent investment. Therefore could it be advantageous / possible to use the immaterial investment's measuring and evaluation techniques for studying the quality politics return of investment?

  8. A microelectronic portal imaging device for image guided conformal microirradiation of murine cancer models.

    Science.gov (United States)

    Price, Samantha G; Silvius, Alexander A; Izaguirre, Enrique W

    2014-01-01

    Image guided conformal small animal orthovoltage microirradiators are currently under development to perform radiobiological experiments with preclinical cancer models. An important component of these instruments is the treatment delivery image guidance system, a microelectronic portal imaging device (μEPID). Here, we present the design and implementation of a μEPID, specifically designed and constructed for small animal orthovoltage microirradiators. The μEPID can acquire images in the range of 60 kVp to 320 kVp x-ray photon energies and can endure high doses from orthovoltage beams without radiation damage. The μEPID can acquire 200 μm resolution images at a rate of 17 frames per second for online in vivo co-registration between irradiation beams and small animal anatomy. An exposure with less than 1% of a 2 Gy treatment field is required for imaging, which is an adequate ratio between imaging dose and treatment dose to avoid undesired irradiation of healthy tissue or alteration of the preclinical cancer model. The μEPID was calibrated for microdosimetry with a precision of 4.1% with respect to an ion chamber, used as a gold standard. To validate the in vivo device performance, irradiations of lung, brain, and xenograft breast cancer preclinical models were performed and analyzed.

  9. Finite element modelling for the investigation of edge effect in acoustic micro imaging of microelectronic packages

    Science.gov (United States)

    Shen Lee, Chean; Zhang, Guang-Ming; Harvey, David M.; Ma, Hong-Wei; Braden, Derek R.

    2016-02-01

    In acoustic micro imaging of microelectronic packages, edge effect is often presented as artifacts of C-scan images, which may potentially obscure the detection of defects such as cracks and voids in the solder joints. The cause of edge effect is debatable. In this paper, a 2D finite element model is developed on the basis of acoustic micro imaging of a flip-chip package using a 230 MHz focused transducer to investigate acoustic propagation inside the package in attempt to elucidate the fundamental mechanism that causes the edge effect. A virtual transducer is designed in the finite element model to reduce the coupling fluid domain, and its performance is characterised against the physical transducer specification. The numerical results showed that the under bump metallization (UBM) structure inside the package has a significant impact on the edge effect. Simulated wavefields also showed that the edge effect is mainly attributed to the horizontal scatter, which is observed in the interface of silicon die-to-the outer radius of solder bump. The horizontal scatter occurs even for a flip-chip package without the UBM structure.

  10. CALIBRATION OF DEVICES FOR MEASURING ELEMENTS OF MICRO-ELECTRONIC STRUCTURES

    Directory of Open Access Journals (Sweden)

    G. Trapashko

    2012-01-01

    Full Text Available Development of microelectronics requires solution of the problem ensuring unity of linear measurements in a submicron range. The problem can be solved on the condition that calibration of measuring devices shall be made in accordance with reference samples that is a short length scale.While making calibration of measuring equipment with the help of a reference measure it is important to investigate components of the method accuracy and their influence on measuring results. The paper considers methodical errors which are specific for methods of optical and atomic force microscopy. Calibration results of an optical measuring microscope are given in the paper. The paper reveals that an additive error depends on parameters of a material and the form of measured elements for an optical measuring microscope. The methodical error of atomic force microscopes is predicated on the probe point shape. The paper considers a short length scale used for calibration of optical and atomic force microscopes. Recommendations for users of the measuring equipment are formulated in the paper.

  11. Failure analysis concepts for microelectronics technologies and manufacturing of the future

    Science.gov (United States)

    Boit, Christian; Weiland, Rainer; Olbrich, A.; Muehle, U.; Simmnacher, B.

    2001-04-01

    The answer of Failure Analysis (F/A) to the technological innovations in microelectronics in the past was: with a slight evolution (i.e. optical microscope -- SEM -- TEM) we can do it. The innovations around the corner today enforce a paradigm shift in F/A to match the challenges by increasing wafer sizes, decreasing feature sizes and new package concepts. This presentation highlights various aspects of the small feature size time bomb (how TEM becomes mandatory and obsolete synchronously), the completely new inline F/A approach on productive wafers inevitable from 300 nm wafer size on, and the reinvention of electrical fail site localization techniques, now from the backside of the die due to new package concepts and innumerable metal layers. Even if F/A manages to overcome all these challenges from a technical point of view, the according revolution in terms of methods, skills and tools implies a cost explosion unless F/A becomes an active part in the business process and the projects of development and manufacturing. This holds even under the assumption that a rising number of today's F/A problems will be solved by modern testing techniques. Only this way F/A can deliver custom-tailored solutions that are optimized in productivity and time to result, and that fulfill the cost reduction requirements of semiconductor products.

  12. Can zinc aluminate-titania composite be an alternative for alumina as microelectronic substrate?

    Science.gov (United States)

    Roshni, Satheesh Babu; Sebastian, Mailadil Thomas; Surendran, Kuzhichalil Peethambharan

    2017-01-01

    Alumina, thanks to its superior thermal and dielectric properties, has been the leading substrate over several decades, for power and microelectronics circuits. However, alumina lacks thermal stability since its temperature coefficient of resonant frequency (τf) is far from zero (−60 ppmK−1). The present paper explores the potentiality of a ceramic composite 0.83ZnAl2O4-0.17TiO2 (in moles, abbreviated as ZAT) substrates for electronic applications over other commercially-used alumina-based substrates and synthesized using a non-aqueous tape casting method. The present substrate has τf of + 3.9 ppmK−1 and is a valuable addition to the group of thermo-stable substrates. The ZAT substrate shows a high thermal conductivity of 31.3 Wm−1K−1 (thermal conductivity of alumina is about 24.5 Wm−1K−1), along with promising mechanical, electrical and microwave dielectric properties comparable to that of alumina-based commercial substrates. Furthermore, the newly-developed substrate material shows exceptionally good thermal stability of dielectric constant, which cannot be met with any of the alumina-based HTCC substrates. PMID:28084459

  13. Interfacial Compatibility in Microelectronics Moving Away from the Trial and Error Approach

    CERN Document Server

    Laurila, Tomi; Paulasto-Kröckel, Mervi; Turunen, Markus; Mattila, Toni T; Kivilahti, Jorma

    2012-01-01

    Interfaces between dissimilar materials are met everywhere in microelectronics and microsystems. In order to ensure faultless operation of these highly sophisticated structures, it is mandatory to have fundamental understanding of materials and their interactions in the system. In this difficult task, the “traditional” method of trial and error is not feasible anymore; it takes too much time and repeated efforts. In Interfacial Compatibility in Microelectronics, an alternative approach is introduced. In this revised method four fundamental disciplines are combined: i) thermodynamics of materials ii) reaction kinetics iii) theory of microstructures and iv) stress and strain analysis. The advantages of the method are illustrated in Interfacial Compatibility in Microelectronics which includes: •solutions to several common reliability issues in microsystem technology, •methods to understand and predict failure mechanisms at interfaces between dissimilar materials and •an approach to DFR based on deep un...

  14. Symmetric miniaturized heating system for active microelectronic devices

    Science.gov (United States)

    McCracken, Michael; Mayer, Michael; Jourard, Isaac; Moon, Jeong-Tak; Persic, John

    2010-07-01

    To qualify interconnect technologies such as microelectronic fine wire bonds for mass production of integrated circuit (IC) packages, it is necessary to perform accelerated aging tests, e.g., to age a device at an elevated temperature or to subject the device to thermal cycling and measure the decrease of interconnect quality. There are downsides to using conventional ovens for this as they are relatively large and have relatively slow temperature change rates, and if electrical connections are required between monitoring equipment and the device being heated, they must be located inside the oven and may be aged by the high temperatures. Addressing these downsides, a miniaturized heating system (minioven) is presented, which can heat individual IC packages containing the interconnects to be tested. The core of this system is a piece of copper cut from a square shaped tube with high resistance heating wire looped around it. Ceramic dual in-line packages are clamped against either open end of the core. One package contains a Pt100 temperature sensor and the other package contains the device to be aged placed in symmetry to the temperature sensor. According to the temperature detected by the Pt100, a proportional-integral-derivative controller adjusts the power supplied to the heating wire. The system maintains a dynamic temperature balance with the core hot and the two symmetric sides with electrical connections to the device under test at a cooler temperature. Only the face of the package containing the device is heated, while the socket holding it remains below 75 °C when the oven operates at 200 °C. The minioven can heat packages from room temperature up to 200 °C in less than 5 min and maintain this temperature at 28 W power. During long term aging, a temperature of 200 °C was maintained for 1120 h with negligible resistance change of the heating wires after 900 h (heating wire resistance increased 0.2% over the final 220 h). The device is also subjected to

  15. Symmetric miniaturized heating system for active microelectronic devices.

    Science.gov (United States)

    McCracken, Michael; Mayer, Michael; Jourard, Isaac; Moon, Jeong-Tak; Persic, John

    2010-07-01

    To qualify interconnect technologies such as microelectronic fine wire bonds for mass production of integrated circuit (IC) packages, it is necessary to perform accelerated aging tests, e.g., to age a device at an elevated temperature or to subject the device to thermal cycling and measure the decrease of interconnect quality. There are downsides to using conventional ovens for this as they are relatively large and have relatively slow temperature change rates, and if electrical connections are required between monitoring equipment and the device being heated, they must be located inside the oven and may be aged by the high temperatures. Addressing these downsides, a miniaturized heating system (minioven) is presented, which can heat individual IC packages containing the interconnects to be tested. The core of this system is a piece of copper cut from a square shaped tube with high resistance heating wire looped around it. Ceramic dual in-line packages are clamped against either open end of the core. One package contains a Pt100 temperature sensor and the other package contains the device to be aged placed in symmetry to the temperature sensor. According to the temperature detected by the Pt100, a proportional-integral-derivative controller adjusts the power supplied to the heating wire. The system maintains a dynamic temperature balance with the core hot and the two symmetric sides with electrical connections to the device under test at a cooler temperature. Only the face of the package containing the device is heated, while the socket holding it remains below 75 degrees C when the oven operates at 200 degrees C. The minioven can heat packages from room temperature up to 200 degrees C in less than 5 min and maintain this temperature at 28 W power. During long term aging, a temperature of 200 degrees C was maintained for 1120 h with negligible resistance change of the heating wires after 900 h (heating wire resistance increased 0.2% over the final 220 h). The

  16. Creep of Two-Phase Microstructures for Microelectronic Applications

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, Heidi Linch [Univ. of California, Berkeley, CA (United States)

    1998-12-01

    The mechanical properties of low-melting temperature alloys are highly influenced by their creep behavior. This study investigates the dominant mechanisms that control creep behavior of two-phase, low-melting temperature alloys as a function of microstructure. The alloy systems selected for study were In-Ag and Sn-Bi because their eutectic compositions represent distinctly different microstructure.” The In-Ag eutectic contains a discontinuous phase while the Sn-Bi eutectic consists of two continuous phases. In addition, this work generates useful engineering data on Pb-free alloys with a joint specimen geometry that simulates microstructure found in microelectronic applications. The use of joint test specimens allows for observations regarding the practical attainability of superplastic microstructure in real solder joints by varying the cooling rate. Steady-state creep properties of In-Ag eutectic, Sn-Bi eutectic, Sn-xBi solid-solution and pure Bi joints have been measured using constant load tests at temperatures ranging from O°C to 90°C. Constitutive equations are derived to describe the steady-state creep behavior for In-Ageutectic solder joints and Sn-xBi solid-solution joints. The data are well represented by an equation of the form proposed by Dom: a power-law equation applies to each independent creep mechanism. Rate-controlling creep mechanisms, as a function of applied shear stress, test temperature, and joint microstructure, are discussed. Literature data on the steady-state creep properties of Sn-Bi eutectic are reviewed and compared with the Sn-xBi solid-solution and pure Bi joint data measured in the current study. The role of constituent phases in controlling eutectic creep behavior is discussed for both alloy systems. In general, for continuous, two-phase microstructure, where each phase exhibits significantly different creep behavior, the harder or more creep resistant phase will dominate the creep behavior in a lamellar microstructure. If a

  17. Technical review of the Sandia Laboratories' Particle Beam Fusion Program

    Energy Technology Data Exchange (ETDEWEB)

    1979-05-18

    This report considers the technical aspects of Sandia Laboratories' Particle Beam Fusion Program and examines the program's initial goals, the progress made to date towards reaching those goals, and the future plans or methods of reaching those original or modified goals. A summary of Sandia Laboratories' effort, which seeks to demonstrate that high voltage pulsed power generated high-current electron or light ion beams can be used to ignite a deuterium or tritium pellet, is provided. A brief review and assessment of the Sandia Pulse Power Program is given. Several critical issues and summaries of the committee members' opinions are discussed.

  18. 微电子封装实验技术的回顾及发展现状%An Overview of Current Research Status of Micro-Experimental Mechanics Methodology in Microelectronics Packaging

    Institute of Scientific and Technical Information of China (English)

    史训清; 谢惠民; 戴福隆

    2002-01-01

    微电子封装,包括微电力系统及光电子封装,为实验力学开辟了新的研究应用领域,也对传统实验测试方法和测量技术提出挑战.本文讨论了微电子封装的发展趋势、微电子封装可靠性及相关力学问题.随后回顾了微观实验技术在微电子封装领域的发展,最后作者着重提出了一些提高微电子封装组件的可靠性的研究方法及思路.%The development of microelectronics packages, including microelectromechanical system (MEMS) and optoelectronics packages, starts a new research and application area of experimental mechanics. It also challenges the traditional experimental mechanics testing approaches and measurement techniques. In this paper, the development trend of electronics packaging is briefed. The reliability issues in microelectronics packages and the corresponding mechanics problems are then addressed. Afterwards, the current research status of microexperimental methodology in microelectronics packaging will be reviewed. Finally, in authors'view, some important research activities, which can help the design of microelectronics packages with robust reliability, are proposed.

  19. Materials science in microelectronics I the relationships between thin film processing and structure

    CERN Document Server

    Machlin, Eugene

    2005-01-01

    Thin films play a key role in the material science of microelectronics, and the subject matter of thin-films divides naturally into two headings: processing / structure relationship, and structure / properties relationship.The first volume of Materials Science in Microelectronics focuses on the first relationship - that between processing and the structure of the thin-film. The state of the thin film's surface during the period that one monolayer exists - before being buried in the next layer - determines the ultimate structure of the thin film, and thus its properties. This

  20. Sandia National Laboratories, Tonopah Test Range Fire Control Bunker (Building 09-51): Photographs and Written Historical and Descriptive Data

    Energy Technology Data Exchange (ETDEWEB)

    Ullrich, Rebecca A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Corporate Archives and History Program

    2017-08-01

    The Fire Control Bunker (Building 09-51) is a contributing element to the Sandia National Laboratories (SNL) Tonopah Test Range (TTR) Historic District. The SNL TTR Historic District played a significant role in U.S. Cold War history in the areas of stockpile surveillance and non-nuclear field testing of nuclear weapons design. The district covers approximately 179,200 acres and illustrates Cold War development testing of nuclear weapons components and systems. This report includes historical information, architectural information, sources of information, project information, maps, blueprints, and photographs.

  1. Sandia National Laboratories/California site environmental report for 1997

    Energy Technology Data Exchange (ETDEWEB)

    Condouris, R.A. [ed.] [Sandia National Labs., Livermore, CA (United States); Holland, R.C. [Science Applications International Corp. (United States)

    1998-06-01

    Sandia National Laboratories (SNL) is committed to conducting its operations in an environmentally safe and sound manner. It is mandatory that activities at SNL/California comply with all applicable environmental statutes, regulations, and standards. Moreover, SNL/California continuously strives to reduce risks to employees, the public, and the environment to the lowest levels reasonably possible. To help verify effective protection of public safety and preservation of the environment, SNL/California maintains an extensive, ongoing environmental monitoring program. This program monitors all significant effluents and the environment at the SNL/California site perimeter. Lawrence Livermore National Laboratory (LLNL) performs off-site external radiation monitoring for both sites. These monitoring efforts ensure that emission controls are effective in preventing contamination of the environment. As part of SNL/California`s Environmental Monitoring Program, an environmental surveillance system measures the possible presence of hazardous materials in groundwater, stormwater, and sewage. The program also includes an extensive environmental dosimetry program, which measures external radiation levels around the Livermore site and nearby vicinity. The Site Environmental Report describes the results of SNL/California`s environmental protection activities during the calendar year. It also summarizes environmental monitoring data and highlights major environmental programs. Overall, it evaluates SNL/California`s environmental management performance and documents the site`s regulatory compliance status.

  2. Feasibility study of medical isotope production at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Massey, C.D.; Miller, D.L.; Carson, S.D. [Sandia National Labs., Albuquerque, NM (United States). Environmental Regulatory Assessment Dept.] [and others

    1995-12-01

    In late 1994, Sandia National Laboratories in Albuquerque, New Mexico, (SNL/NM), was instructed by the Department of Energy (DOE) Isotope Production and Distribution Program (IPDP) to examine the feasibility of producing medically useful radioisotopes using the Annular Core Research Reactor (ACRR) and the Hot Cell Facility (HCF). Los Alamos National Laboratory (LANL) would be expected to supply the targets to be irradiated in the ACRR. The intent of DOE would be to provide a capability to satisfy the North American health care system demand for {sup 99}Mo, the parent of {sup 99m}Tc, in the event of an interruption in the current Canadian supply. {sup 99m}Tc is used in 70 to 80% of all nuclear medicine procedures in the US. The goal of the SNL/NM study effort is to determine the physical plant capability, infrastructure, and staffing necessary to meet the North American need for {sup 99}Mo and to identify and examine all issues with potential for environmental impact.

  3. Sandia-Power Surety Task Force Hawaii foam analysis.

    Energy Technology Data Exchange (ETDEWEB)

    McIntyre, Annie

    2010-11-01

    The Office of Secretary of Defense (OSD) Power Surety Task Force was officially created in early 2008, after nearly two years of work in demand reduction and renewable energy technologies to support the Warfighter in Theater. The OSD Power Surety Task Force is tasked with identifying efficient energy solutions that support mission requirements. Spray foam insulation demonstrations were recently expanded beyond field structures to include military housing at Ft. Belvoir. Initial results to using the foam in both applications are favorable. This project will address the remaining key questions: (1) Can this technology help to reduce utility costs for the Installation Commander? (2) Is the foam cost effective? (3) What application differences in housing affect those key metrics? The critical need for energy solutions in Hawaii and the existing relationships among Sandia, the Department of Defense (DOD), the Department of Energy (DOE), and Forest City, make this location a logical choice for a foam demonstration. This project includes application and analysis of foam to a residential duplex at the Waikulu military community on Oahu, Hawaii, as well as reference to spray foam applied to a PACOM facility and additional foamed units on Maui, conducted during this project phase. This report concludes the analysis and describes the utilization of foam insulation at military housing in Hawaii and the subsequent data gathering and analysis.

  4. Calendar Year 2013 Annual Site Environmental Report for Sandia National Laboratories, Albuquerque, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Griffith, Stacy [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-09-01

    Sandia National Laboratories, New Mexico is a government-owned/contractor-operated facility. Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, manages and operates the laboratory for the U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA). The DOE/NNSA, Sandia Field Office administers the contract and oversees contractor operations at the site. This annual report summarizes data and the compliance status of Sandia Corporation’s sustainability, environmental protection, and monitoring programs through December 31, 2013. Major environmental programs include air quality, water quality, groundwater protection, terrestrial surveillance, waste management, pollution prevention, environmental restoration, oil and chemical spill prevention, and implementation of the National Environmental Policy Act. Environmental monitoring and surveillance programs are required by DOE Order 231.1B, Environment, Safety, and Health Reporting (DOE 2012).

  5. Calendar year 2003 annual site environmental report for Sandia National Laboratories, New Mexico.

    Energy Technology Data Exchange (ETDEWEB)

    Wagner, Katrina; Sanchez, Rebecca V.; Mayeux, Lucie; Koss, Susan I.; Salinas, Stephanie A.

    2004-09-01

    Sandia National Laboratories, New Mexico (SNL/NM) is a government-owned, contractor-operated facility owned by the U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA) and managed by the Sandia Site Office (SSO), Albuquerque, New Mexico. Sandia Corporation, a wholly-owned subsidiary of Lockheed Martin Corporation, operates SNL/NM. This annual report summarizes data and the compliance status of Sandia Corporation's environmental protection and monitoring programs through December 31, 2003. Major environmental programs include air quality, water quality, groundwater protection, terrestrial surveillance, waste management, pollution prevention (P2), environmental restoration (ER), oil and chemical spill prevention, and the National Environmental Policy Act (NEPA). Environmental monitoring and surveillance programs are required by DOE Order 450.1, ''Environmental Protection Program'' (DOE 2003a) and DOE Order 231.1 Chg.2, ''Environment, Safety, and Health Reporting'' (DOE 1996).

  6. Calendar year 2002 annual site environmental report for Sandia National Laboratories, New Mexico.

    Energy Technology Data Exchange (ETDEWEB)

    Wagner, Katrina; Sanchez, Rebecca V.; Mayeux, Lucie; Koss, Susan I.; Salinas, Stephanie A.

    2003-09-01

    Sandia National Laboratories, New Mexico (SNL/NM) is a government-owned, contractor-operated facility overseen by the U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA) through the Sandia Site Office (SSO), Albuquerque, New Mexico. Sandia Corporation, a wholly-owned subsidiary of Lockheed Martin Corporation, operates SNL/NM. This annual report summarizes data and the compliance status of Sandia Corporation's environmental protection and monitoring programs through December 31, 2002. Major environmental programs include air quality, water quality, groundwater protection, terrestrial surveillance, waste management, pollution prevention (P2), environmental restoration (ER), oil and chemical spill prevention, and the National Environmental Policy Act (NEPA). Environmental monitoring and surveillance programs are required by DOE Order 5400.1, General Environmental Protection Program (DOE 1990) and DOE Order 231.1, Environment, Safety, and Health Reporting (DOE 1996).

  7. Calendar year 2004 annual site environmental report:Sandia National Laboratories, Albuquerque, New Mexico.

    Energy Technology Data Exchange (ETDEWEB)

    Montoya, Amber L.; Goering, Teresa Lynn; Wagner, Katrina; Koss, Susan I.; Salinas, Stephanie A.

    2005-09-01

    Sandia National Laboratories, New Mexico (SNL/NM) is a government-owned, contractor-operated facility owned by the U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA) and managed by the Sandia Site Office (SSO), Albuquerque, New Mexico. Sandia Corporation, a wholly-owned subsidiary of Lockheed Martin Corporation, operates SNL/NM. This annual report summarizes data and the compliance status of Sandia Corporation's environmental protection and monitoring programs through December 31, 2004. Major environmental programs include air quality, water quality, groundwater protection, terrestrial surveillance, waste management, pollution prevention (P2), environmental restoration (ER), oil and chemical spill prevention, and the National Environmental Policy Act (NEPA). Environmental monitoring and surveillance programs are required by DOE Order 450.1, Environmental Protection Program (DOE 2005) and DOE Order 231.1A, Environment, Safety, and Health Reporting (DOE 2004a). (DOE 2004a).

  8. Sandia Engineering Analysis Code Access System v. 2.0.1

    Energy Technology Data Exchange (ETDEWEB)

    2017-10-30

    The Sandia Engineering Analysis Code Access System (SEACAS) is a suite of preprocessing, post processing, translation, visualization, and utility applications supporting finite element analysis software using the Exodus database file format.

  9. Architect and engineering costs at Los Alamos and Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-08-01

    The objective of this audit was to determine whether architect and engineering (A-E) costs at Los Alamos National Laboratory and Sandia National Laboratories were reasonable in comparison with industry standards.

  10. Corti's organ physiology-based cochlear model: a microelectronic prosthetic implant

    Science.gov (United States)

    Rios, Francisco; Fernandez-Ramos, Raquel; Romero-Sanchez, Jorge; Martin, Jose Francisco

    2003-04-01

    Corti"s Organ is an Electro-Mechanical transducer that allows the energy coupling between acoustical stimuli and auditory nerve. Although the structure and funtionality of this organ are complex, state of the art models have been currently developed and tested. Cochlea model presented in this paper is based on the theories of Bekesy and others and concerns on the behaviour of auditory system on frequency-place domain and mechanisms of lateral inhibition. At the same time, present state of technology will permit us developing a microsystem that reproduce this phenomena applied to hearing aid prosthesis. Corti"s Organ is composed of more than 20.000 cilia excited by mean of travelling waves. These waves produce relative pressures distributed along the cochlea, exciting an specific number of cilia in a local way. Nonlinear mechanisms of local adaptation to the intensity (external cilia cells) and lateral inhibition (internal cilia cells) allow the selection of very few elements excited. These transmit a very precise intensity and frequency information. These signals are the only ones coupled to the auditory nerve. Distribution of pressure waves matches a quasilogaritmic law due to Cochlea morphology. Microsystem presented in this paper takes Bark"s law as an approximation to this behaviour consisting on grouped arbitrary elements composed of a set of selective coupled exciters (bank of filters according to Patterson"s model).These sets apply the intensity adaptation principles and lateral inhibition. Elements excited during the process generate a bioelectric signal in the same way than cilia cell. A microelectronic solution is presented for the development of an implantable prosthesis device.

  11. Aquatic macroinvertebrates and water quality of Sandia Canyon, Los Alamos National Laboratory, December 1992--October 1993. Status report

    Energy Technology Data Exchange (ETDEWEB)

    Cross, S. [Ewing Technical Design, Inc., Albuquerque, NM (United States)

    1994-09-01

    In the summer of 1990, an accidental spill from the TA-3 Power Plant Environment Tank released more than 3,785 liters of sulfuric acid into upper Sandia Canyon. The Biological Resource Evaluation Team (BRET) of EM-8 at Los Alamos National Laboratory (LANL) has collected aquatic samples from the stream within Sandia Canyon since then. These field studies gather water quality measurements and collect macroinvertebrates from permanent sampling sites. An earlier report by Bennett (1994) discusses previous BRET aquatic studies in Sandia Canyon. This report updates and expands Bennett`s initial findings. During 1993, BRET collected water quality data and aquatic macroinvertebrates at five permanent stations within the canyon. The substrates of the upper three stations are largely sands and silts while the substrates of the two lower stations are largely rock and cobbles. The two upstream stations are located near outfalls that discharge industrial and sanitary waste effluent. The third station is within a natural cattail marsh, approximately 0.4 km (0.25 mi) downstream from Stations SC1 and SC2. Water quality parameters are slightly different at these first three stations from those expected of natural streams, suggesting slightly degraded water quality. Correspondingly, the macroinvertebrate communities at these stations are characterized by low diversities and poorly-developed community structures. The two downstream stations appear to be in a zone of recovery, where water quality parameters more closely resemble those found in natural streams of the area. Macroinvertebrate diversity increases and community structure becomes more complex at the two lower stations, which are further indications of improved water quality downstream.

  12. Microelectronic Information Processing Systems: Computing Systems. Summary of Awards Fiscal Year 1994.

    Science.gov (United States)

    National Science Foundation, Arlington, VA. Directorate for Computer and Information Science and Engineering.

    The purpose of this summary of awards is to provide the scientific and engineering communities with a summary of the grants awarded in 1994 by the National Science Foundation's Division of Microelectronic Information Processing Systems. Similar areas of research are grouped together. Grantee institutions and principal investigators are identified…

  13. Poly(3-hexylthiophene)/ZnO hybrid pn junctions for microelectronics applications

    DEFF Research Database (Denmark)

    Katsia, E.; Huby, N.; Tallarida, G.

    2009-01-01

    Hybrid poly(3-hexylthiophene)/ZnO devices are investigated as rectifying heterojunctions for microelectronics applications. A low-temperature atomic layer deposition of ZnO on top of poly(3-hexylthiophene) allows the fabrication of diodes featuring a rectification ratio of nearly 105 at ±4 V...

  14. Environmental Survey preliminary report, Sandia National Laboratories, Livermore, California

    Energy Technology Data Exchange (ETDEWEB)

    1988-01-01

    This report contains the preliminary findings based on the first phase of an Environmental Survey at the Department of Energy (DOE) Sandia National Laboratories Livermore (SNLL), located at Livermore, California. The Survey is being conducted by DOE's Office of Environment, Safety and Health. The SNLL Survey is a portion of the larger, comprehensive DOE Environmental Survey encompassing all major operating facilities of DOE. The DOE Environmental Survey is one of a series of initiatives announced on September 18, 1985, by Secretary of Energy, John S. Herrington, to strengthen the environmental, safety, and health programs and activities within DOE. The purpose of the Environmental Survey is to identify, via a no fault'' baseline Survey of all the Department's major operating facilities, environmental problems and areas of environmental risk. The identified problem areas will be prioritized on a Department-wide basis in order of importance in 1989. The findings in this report are subject to modification based on the results from the Sampling and Analysis Phase of the Survey. The findings are also subject to modification based on comments from the Albuquerque Operations Office concerning the technical accuracy of the findings. The modified preliminary findings and any other appropriate changes will be incorporated into an Interim Report. The Interim Report will serve as the site-specific source for environmental information generated by the Survey, and ultimately as the primary source of information for the DOE-wide prioritization of environmental problems in the Survey Summary Report. 43 refs., 21 figs., 24 tabs.

  15. Alteration in the Madera limestone and Sandia formation from core hole VC-1 Valles Caldera, New Mexico

    Science.gov (United States)

    Keith, Terry E. C.

    1988-06-01

    Core hole VC-1 penetrated the southwestern ring fracture zone of the 1.1 Ma Valles caldera and at a depth of 333 m intersected the top of the Paleozoic section including the Abo Formation, Madera Limestone, and Sandia Formation, reaching a total depth of 856 m. The Paleozoic rocks, which consist of thin-bedded limestone, siltstone, mudstone, sandstone, and local conglomerate, are overlain by volcanic rocks of the caldera moat that are less than 0.6 Ma. Diagenetic and at least three hydrothermal alteration stages were identified in the Madera Limestone and Sandia Formation. Diagenetic clay alteration was pervasive throughout the sedimentary rocks. Volcanic activity at 16.5 Ma and continuing through the formation of the Valles caldera resulted in high thermal gradients, which caused recrystallization of diagenetic clay minerals. Interstratified smectite-illite is the most diagnostic clay mineral throughout the section; structurally, the illite component in the ordered interstratified illite-smectite changes gradationally from 70% at the top of the Madera Limestone to 95% at the base of the section in the Sandia Formation. Pyrite that occurs as small clots and lenses as well as finely disseminated is interpreted as being of diagenetic origin, especially in organic-rich beds. Low permeability of much of the Paleozoic section precluded the deposition of hydrothermal minerals except in fractures and intergranular space in some of the more permeable sandstone and brecciated horizons. Three stages of hydrothermal mineral deposition are defined. Stage I is widespread and includes mainly chlorite, calcite, pyrite, and interstratified smectite-illite that was formed prior to caldera development at temperatures approximating 200°C. Stage II is characterized by quartz, sericite, and scarce sulfides deposited locally by fluids at approximately 275°C shortly before or at the time of early caldera-related volcanism. The Stage III hydrothermal event, associated with formation of

  16. Electrochemical investigations of advanced materials for microelectronic and energy storage devices

    Science.gov (United States)

    Goonetilleke, Pubudu Chaminda

    A broad range of electrochemical techniques are employed in this work to study a selected set of advanced materials for applications in microelectronics and energy storage devices. The primary motivation of this study has been to explore the capabilities of certain modern electrochemical techniques in a number of emerging areas of material processing and characterization. The work includes both aqueous and non-aqueous systems, with applications in two rather general areas of technology, namely microelectronics and energy storage. The sub-systems selected for investigation are: (i) Electrochemical mechanical and chemical mechanical planarization (ECMP and CMP, respectively), (ii) Carbon nanotubes in combination with room temperature ionic liquids (ILs), and (iii) Cathode materials for high-performance Li ion batteries. The first group of systems represents an important building block in the fabrication of microelectronic devices. The second and third groups of systems are relevant for new energy storage technologies, and have generated immense interests in recent years. A common feature of these different systems is that they all are associated with complex surface reactions that dictate the performance of the devices based on them. Fundamental understanding of these reactions is crucial to further development and expansion of their associated technologies. It is the complex mechanistic details of these surface reactions that we address using a judicious combination of a number of state of the art electrochemical techniques. The main electrochemical techniques used in this work include: (i) Cyclic voltammetry (CV) and slow scan cyclic voltammetry (SSCV, a special case of CV); (ii) Galvanostatic (or current-controlled) measurements; (iii) Electrochemical impedance spectroscopy (EIS), based on two different methodologies, namely, Fourier transform EIS (FT-EIS, capable of studying fast reaction kinetics in a time-resolved mode), and EIS using frequency response

  17. Addressing environmental justice under the National Environment Policy Act at Sandia National Laboratories/New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, T.M.; Bleakly, D.R.

    1997-04-01

    Under Executive Order 12898, Federal Actions to Address Environmental Justice in Minority Populations and Low-Income Populations, the Department of Energy (DOE) and Sandia National Laboratories New Mexico (SNL) are required to identify and address, as appropriate, disproportionately high, adverse human health or environmental effects of their activities on minority and low-income populations. The National Environmental Policy Act (NEPA) also requires that environmental justice issues be identified and addressed. This presents a challenge for SNL because it is located in a culturally diverse area. Successfully addressing potential impacts is contingent upon accurately identifying them through objective analysis of demographic information. However, an effective public participation process, which is necessarily subjective, is also needed to understand the subtle nuances of diverse populations that can contribute to a potential impact, yet are not always accounted for in a strict demographic profile. Typically, there is little or no coordination between these two disparate processes. This report proposes a five-step method for reconciling these processes and uses a hypothetical case study to illustrate the method. A demographic analysis and community profile of the population within 50 miles of SNL were developed to support the environmental justice analysis process and enhance SNL`s NEPA and public involvement programs. This report focuses on developing a methodology for identifying potentially impacted populations. Environmental justice issues related to worker exposures associated with SNL activities will be addressed in a separate report.

  18. Sandia technology. Volume 13, number 2 Special issue : verification of arms control treaties.

    Energy Technology Data Exchange (ETDEWEB)

    1989-03-01

    Nuclear deterrence, a cornerstone of US national security policy, has helped prevent global conflict for over 40 years. The DOE and DoD share responsibility for this vital part of national security. The US will continue to rely on nuclear deterrence for the foreseeable future. In the late 1950s, Sandia developed satellite-borne nuclear burst detection systems to support the treaty banning atmospheric nuclear tests. This activity has continued to expand and diversify. When the Non-Proliferation Treaty was ratified in 1970, we began to develop technologies to protect nuclear materials from falling into unauthorized hands. This program grew and now includes systems for monitoring the movement and storage of nuclear materials, detecting tampering, and transmiting sensitive data securely. In the late 1970s, negotiations to further limit underground nuclear testing were being actively pursued. In less than 18 months, we fielded the National Seismic Station, an unattended observatory for in-country monitoring of nuclear tests. In the mid-l980s, arms-control interest shifted to facility monitoring and on-site inspection. Our Technical On-site Inspection Facility is the national test bed for perimeter and portal monitoring technology and the prototype for the inspection portal that was recently installed in the USSR under the Intermediate-Range Nuclear Forces accord. The articles in the special issue of Sundiu Technology describe some of our current contributions to verification technology. This work supports the US policy to seek realistic arms control agreements while maintaining our national security.

  19. Ceramic materials of low-temperature synthesis for dielectric coating applied by 3D aerosol printing used in nano- and microelectronics, lighting engineering, and spacecraft control devices

    Science.gov (United States)

    Ivanov, A. A.; Tuev, V. I.; Nisan, A. V.; Potapov, G. N.

    2016-11-01

    A synthesis technique of low-temperature ceramic material based on aluminosilicates of dendrimer morphology capable to contain up to 80 wt % of nitrides and oxides of high-melting compounds as filler has been developed. The synthesis is based on a sol-gel method followed by mechanochemical treatment and ultrasonic dispersing. Dielectric ceramic layers with the layer thickness in the nanometer range and high thermal conductivity have been obtained for the first time by 3D aerosol printing of the synthesized material. The study of the obtained ceramic coating on the metal surface (Al) has proved its use prospects in microelectronics, light engineering, and devices for special purposes.

  20. 2017 Annual Terrestrial Sampling Plan for Sandia National Laboratories/New Mexico on Kirtland Air Force Base

    Energy Technology Data Exchange (ETDEWEB)

    Griffith, Stacy R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-02-01

    The 2017 Annual Terrestrial Sampling Plan for Sandia National Laboratories/New Mexico on Kirtland Air Force Base has been prepared in accordance with the “Letter of Agreement Between Department of Energy, National Nuclear Security Administration, Sandia Field Office (DOE/NNSA/SFO) and 377th Air Base Wing (ABW), Kirtland Air Force Base (KAFB) for Terrestrial Sampling” (signed January 2017), Sandia National Laboratories, New Mexico (SNL/NM). The Letter of Agreement requires submittal of an annual terrestrial sampling plan.

  1. Routine environmental audit of the Sandia National Laboratories, California, Livermore, California

    Energy Technology Data Exchange (ETDEWEB)

    1994-03-01

    This report documents the results of the Routine Environmental Audit of the Sandia National Laboratories, Livermore, California (SNL/CA). During this audit the activities the Audit Team conducted included reviews of internal documents and reports from preview audits and assessments; interviews with US Department of Energy (DOE), State of California regulators, and contractor personnel; and inspections and observations of selected facilities and operations. The onsite portion of the audit was conducted from February 22 through March 4, 1994, by the DOE Office of Environmental Audit (EH-24), located within the Office of Environment, Safety, and Health (EH). The audit evaluated the status of programs to ensure compliance with Federal, state, and local environmental laws and regulations; compliance with DOE Orders, guidance, and directives; and conformance with accepted industry practices and standards of performance. The audit also evaluated the status and adequacy of the management systems developed to address environmental requirements. The audit`s functional scope was comprehensive and included all areas of environmental management and a programmatic evaluation of NEPA and inactive waste sites.

  2. Robotic Lunar Rover Technologies and SEI Supporting Technologies at Sandia National Laboratories

    Science.gov (United States)

    Klarer, Paul R.

    1992-01-01

    Existing robotic rover technologies at Sandia National Laboratories (SNL) can be applied toward the realization of a robotic lunar rover mission in the near term. Recent activities at the SNL-RVR have demonstrated the utility of existing rover technologies for performing remote field geology tasks similar to those envisioned on a robotic lunar rover mission. Specific technologies demonstrated include low-data-rate teleoperation, multivehicle control, remote site and sample inspection, standard bandwidth stereo vision, and autonomous path following based on both internal dead reckoning and an external position location update system. These activities serve to support the use of robotic rovers for an early return to the lunar surface by demonstrating capabilities that are attainable with off-the-shelf technology and existing control techniques. The breadth of technical activities at SNL provides many supporting technology areas for robotic rover development. These range from core competency areas and microsensor fabrication facilities, to actual space qualification of flight components that are designed and fabricated in-house.

  3. Cryogenic capability for equation-of-state measurements on the Sandia Z pulsed radiation source

    Energy Technology Data Exchange (ETDEWEB)

    Hanson, D.L.; Johnston, R.R.; Asay, J.R.

    1998-02-01

    Experimental cryogenic capabilities are essential for the study of ICF high-gain target and weapons effects issues involving dynamic materials response at low temperatures. The authors are developing a general purpose cryogenic target system for precision radiation driven EOS and shock physics experiments at liquid helium temperatures on the Sandia Z pulsed radiation source. Cryogenic sample cooling in the range of 6--30 K is provided by a liquid helium cryostat and an active temperature control system. The cryogenic target assembly is capable of condensing liquid deuterium samples from the gas phase at about 20 K, as well as cooling solid samples such as beryllium and CH ablators for ICF. The target assembly will also include the capability to use various shock diagnostics, such as VISAR interferometry and fiber-optic-coupled shock breakout diagnostics. They are characterizing the thermal and optical performance of the system components in an off-line cryogenic test facility and have designed an interface to introduce the cryogenic transfer lines, gas lines, and sensor cables into the Z vacuum section. Survivability of high-value cryogenic components in the destructive post-implosion environment of Z is a major issue driving the design of this cryogenic target system.

  4. User's manual for the Sandia Waste-Isolation Flow and Transport model (SWIFT).

    Energy Technology Data Exchange (ETDEWEB)

    Reeves, Mark; Cranwell, Robert M.

    1981-11-01

    This report describes a three-dimensional finite-difference model (SWIFT) which is used to simulate flow and transport processes in geologic media. The model was developed for use by the Nuclear Regulatory Commission in the analysis of deep geologic nuclear waste-disposal facilities. This document, as indicated by the title, is a user's manual and is intended to facilitate the use of the SWIFT simulator. Mathematical equations, submodels, application notes, and a description of the program itself are given herein. In addition, a complete input data guide is given along with several appendices which are helpful in setting up a data-input deck. Computer code SWIFT (Sandia Waste Isolation, Flow and Transport Model) is a fully transient, three-dimensional model which solves the coupled equations for transport in geologic media. The processes considered are: (1) fluid flow; (2) heat transport; (3) dominant-species miscible displacement; and (4) trace-species miscible displacement. The first three processes are coupled via fluid density and viscosity. Together they provide the velocity field on which the fourth process depends.

  5. Gamma Irradiation Facility at Sandia National Laboratories, Albuquerque, New Mexico. Final environmental assessment

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    The US Department of Energy (DOE) has prepared an environmental assessment (EA) on the proposed construction and operation of a new Gamma Irradiation Facility (GIF) at Sandia National Laboratories/New Mexico (SNL/NM). This facility is needed to: enhance capabilities to assure technical excellence in nuclear weapon radiation environments testing, component development, and certification; comply with all applicable ES and H safeguards, standards, policies, and regulations; reduce personnel radiological exposure to comply with ALARA limits in accordance with DOE orders and standards; consolidate major gamma ray sources into a central, secured area; and reduce operational risks associated with operation of the GIF and LICA in their present locations. This proposed action provides for the design, construction, and operation of a new GIF located within TA V and the removal of the existing GIF and Low Intensity Cobalt Array (LICA). The proposed action includes potential demolition of the gamma shield walls and removal of equipment in the existing GIF and LICA. The shielding pool used by the existing GIF will remain as part of the ACRR facility. Transportation of the existing {sup 60}Co sources from the existing LICA and GIF to the new facility is also included in the proposed action. Relocation of the gamma sources to the new GIF will be accomplished by similar techniques to those used to install the sources originally.

  6. SEMICONDUCTOR INTEGRATED CIRCUITS: A four-channel microelectronic system for neural signal regeneration

    Science.gov (United States)

    Shushan, Xie; Zhigong, Wang; Xiaoying, Lü; Wenyuan, Li; Haixian, Pan

    2009-12-01

    This paper presents a microelectronic system which is capable of making a signal record and functional electric stimulation of an injured spinal cord. As a requirement of implantable engineering for the regeneration microelectronic system, the system is of low noise, low power, small size and high performance. A front-end circuit and two high performance OPAs (operational amplifiers) have been designed for the system with different functions, and the two OPAs are a low-noise low-power two-stage OPA and a constant-gm RTR input and output OPA. The system has been realized in CSMC 0.5-μm CMOS technology. The test results show that the system satisfies the demands of neuron signal regeneration.

  7. Model of control of glow discharge electron gun current for microelectronics production applications

    Science.gov (United States)

    Denbnovetsky, S. V.; Melnyk, V. I.; Melnyk, I. V.; Tugay, B. A.

    2003-04-01

    The problems of simulation of discharge current control and its gas-dynamic stabilization for technological glow discharge electron guns with a cold cathode are considered in a paper. Such guns are successfully operated in soft vacuum and can be used in modern microelectronic technologies for providing of thermal operations with using different technological gases including active ones. The results of theoretical and experimental investigation of automatic control system of current of electron gun which were used for deposition of coatings in reactive gas medium are presented in article. Time of regulation for considered system did not exceed 400 ms. Is proved, that the automatic control of a current of a glow discharge electron gun by pressure variation its volume is effective on all operation range of pressure, and the minimum time of a current regulation can be tens -- hundred of ms, and this fact is allow to use in the majority of technological operations for microelectronic production.

  8. Design and initial deployment of the wireless local area networking infrastructure at Sandia National Laboratories.

    Energy Technology Data Exchange (ETDEWEB)

    Long, John P.; Hamill, Michael J.; Mitchell, M. G.; Miller, Marc M.; Witzke, Edward L.; Wiener, Dallas J

    2006-11-01

    A major portion of the Wireless Networking Project at Sandia National Laboratories over the last few years has been to examine IEEE 802.11 wireless networking for possible use at Sandia and if practical, introduce this technology. This project team deployed 802.11a, b, and g Wireless Local Area Networking at Sandia. This report examines the basics of wireless networking and captures key results from project tests and experiments. It also records project members thoughts and designs on wireless LAN architecture and security issues. It documents some of the actions and milestones of this project, including pilot and production deployment of wireless networking equipment, and captures the team's rationale behind some of the decisions made. Finally, the report examines lessons learned, future directions, and conclusions.

  9. Connecting the physical and psychosocial space to Sandia's mission

    Energy Technology Data Exchange (ETDEWEB)

    Emmanuel, Glory Ruth [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Silva, Austin Ray [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-07-01

    Sandia Labs has corporate, lab-wide efforts to enhance the research environment as well as improve physical space. However, these two efforts are usually done in isolation. The integration of physical space design with the nurturing of what we call psychosocial space can foster more efficient and effective creativity, innovation, collaboration, and performance. This paper presents a brief literature review on how academia and industry are studying the integration of physical and psychosocial space and focuses on the efforts that we, the authors, have made to improve the research environment in the Cyber Engineering Research Lab (CERL), home to Group 1460. Interviews with subject matter experts from Silicon Valley and the University of New Mexico plus changes to actual spaces in CERL provided us with six lessons learned when integrating physical and psychosocial space. We describe these six key takeaways in hopes that Sandia will see this area as an evolving research capability that Sandia can both contribute to and benefit from.

  10. Connecting the physical and psychosocial space to Sandia's mission.

    Energy Technology Data Exchange (ETDEWEB)

    Emmanuel, Glory Ruth; Silva, Austin Ray

    2014-07-01

    Sandia Labs has corporate, lab-wide efforts to enhance the research environment as well as improve physical space. However, these two efforts are usually done in isolation. The integration of physical space design with the nurturing of what we call psychosocial space can foster more efficient and effective creativity, innovation, collaboration, and performance. This paper presents a brief literature review on how academia and industry are studying the integration of physical and psychosocial space and focuses on the efforts that we, the authors, have made to improve the research environment in the Cyber Engineering Research Lab (CERL), home to Group 1460. Interviews with subject matter experts from Silicon Valley and the University of New Mexico plus changes to actual spaces in CERL provided us with six lessons learned when integrating physical and psychosocial space. We describe these six key takeaways in hopes that Sandia will see this area as an evolving research capability that Sandia can both contribute to and benefit from.

  11. 2016 Annual Site Environmental Report Sandia National Laboratories/New Mexico.

    Energy Technology Data Exchange (ETDEWEB)

    Salas, Angela Maria [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Griffith, Stacy R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-07-01

    Sandia National Laboratories (SNL) is a multimission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s (DOE’s), National Nuclear Security Administration (NNSA). The DOE/NNSA Sandia Field Office administers the contract and oversees contractor operations at SNL, New Mexico. This Annual Site Environmental Report (ASER) summarizes data and the compliance status of sustainability, environmental protection, and monitoring programs at SNL/NM during calendar year 2016. Major environmental programs include air quality, water quality, groundwater protection, terrestrial and ecological surveillance, waste management, pollution prevention, environmental restoration, oil and chemical spill prevention, and implementation of the National Environmental Policy Act. This ASER is prepared in accordance with and required by DOE O 231.1B, Admin Change 1, Environment, Safety, and Health Reporting.

  12. Energy minimization-based analysis of electrowetting for microelectronics cooling applications

    OpenAIRE

    Bahadur, Vaibhav; Garimella, S V

    2008-01-01

    Electrowetting (EW)-induced droplet motion has been studied over the last decade in view of its promising applications in the field of microfluidics. The objective of the present work is to analyze the physics underlying two specific EW-based applications for microelectronics thermal management. The first of these involves heat absorption by liquid droplets moving on the surface of a chip under EW actuation. Droplet motion between two flat plates under the influence of an electrowetting volta...

  13. Poly(3-hexylthiophene)/ZnO hybrid pn junctions for microelectronics applications

    Science.gov (United States)

    Katsia, E.; Huby, N.; Tallarida, G.; Kutrzeba-Kotowska, B.; Perego, M.; Ferrari, S.; Krebs, F. C.; Guziewicz, E.; Godlewski, M.; Osinniy, V.; Luka, G.

    2009-04-01

    Hybrid poly(3-hexylthiophene)/ZnO devices are investigated as rectifying heterojunctions for microelectronics applications. A low-temperature atomic layer deposition of ZnO on top of poly(3-hexylthiophene) allows the fabrication of diodes featuring a rectification ratio of nearly 105 at ±4 V and a current density of 104 A/cm2. Electrical characteristics are discussed taking into account the chemical structure of the stack and the energy band diagram.

  14. Monitoring Composite Material Pressure Vessels with a Fiber-Optic/Microelectronic Sensor System

    Science.gov (United States)

    Klimcak, C.; Jaduszliwer, B.

    1995-01-01

    We discuss the concept of an integrated, fiber-optic/microelectronic distributed sensor system that can monitor composite material pressure vessels for Air Force space systems to provide assessments of the overall health and integrity of the vessel throughout its entire operating history from birth to end of life. The fiber optic component would include either a semiconductor light emitting diode or diode laser and a multiplexed fiber optic sensing network incorporating Bragg grating sensors capable of detecting internal temperature and strain. The microelectronic components include a power source, a pulsed laser driver, time domain data acquisition hardware, a microprocessor, a data storage device, and a communication interface. The sensing system would be incorporated within the composite during its manufacture. The microelectronic data acquisition and logging system would record the environmental conditions to which the vessel has been subjected to during its storage and transit, e.g., the history of thermal excursions, pressure loading data, the occurrence of mechanical impacts, the presence of changing internal strain due to aging, delamination, material decomposition, etc. Data would be maintained din non-volatile memory for subsequent readout through a microcomputer interface.

  15. Synthesis of the System Modeling and Signal Detecting Circuit of a Novel Vacuum Microelectronic Accelerometer

    Directory of Open Access Journals (Sweden)

    Zhengguo Shang

    2009-05-01

    Full Text Available A novel high-precision vacuum microelectronic accelerometer has been successfully fabricated and tested in our laboratory. This accelerometer has unique advantages of high sensitivity, fast response, and anti-radiation stability. It is a prototype intended for navigation applications and is required to feature micro-g resolution. This paper briefly describes the structure and working principle of our vacuum microelectronic accelerometer, and the mathematical model is also established. The performances of the accelerometer system are discussed after Matlab modeling. The results show that, the dynamic response of the accelerometer system is significantly improved by choosing appropriate parameters of signal detecting circuit, and the signal detecting circuit is designed. In order to attain good linearity and performance, the closed-loop control mode is adopted. Weak current detection technology is studied, and integral T-style feedback network is used in I/V conversion, which will eliminate high-frequency noise at the front of the circuit. According to the modeling parameters, the low-pass filter is designed. This circuit is simple, reliable, and has high precision. Experiments are done and the results show that the vacuum microelectronic accelerometer exhibits good linearity over -1 g to +1 g, an output sensitivity of 543 mV/g, and a nonlinearity of 0.94 %.

  16. AFTI/SITAN (Advanced Fighter Technology Integration/Sandia Inertial Terrain-Aided Navigation) final report

    Energy Technology Data Exchange (ETDEWEB)

    Fellerhoff, J.R.

    1988-11-01

    Sandia Inertial Terrain-Aided Navigation (SITAN) provides continuous position fixes to an inertial navigation system (INS) by real-time comparison of radar altimeter ground clearance measurements with stored digital terrain elevation data (DTED). This is accomplished by using an extended Kalman filter algorithm to estimate the errors in the reference trajectory provided by an INS. In this report, Sandia National Laboratories documents the results of a reimbursable effort funded by the Air Force Wright Aeronautical Laboratories (AFWAL) Avionics Laboratory to flight test SITAN as implemented onboard the Advanced Fighter Technology Integration (AFTI)F-16. 5 refs., 101 figs., 1 tab.

  17. National Environmental Policy Act (NEPA) compliance at Sandia National Laboratories/New Mexico (SNL/NM)

    Energy Technology Data Exchange (ETDEWEB)

    Wolff, T.A. [Sandia National Labs., Albuquerque, NM (United States). Community Involvement and Issues Management Dept.; Hansen, R.P. [Hansen Environmental Consultants, Englewood, CO (United States)

    1998-08-01

    This report on National Environmental Policy Act (NEPA) compliance at Sandia National Laboratories/New Mexico (SNL/NM) chronicles past and current compliance activities and includes a recommended strategy that can be implemented for continued improvement. This report provides a list of important references. Attachment 1 contains the table of contents for SAND95-1648, National Environmental Policy Act (NEPA) Compliance Guide Sandia National Laboratories (Hansen, 1995). Attachment 2 contains a list of published environmental assessments (EAs) and environmental impact statements (EISs) prepared by SNL/NM. Attachment 3 contains abstracts of NEPA compliance papers authored by SNL/NM and its contractors.

  18. Environmental assessment of the Environmental Restoration Project at Sandia National Laboratories/New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Sandia National Laboratories/New Mexico (SNL/NM) is managed and operated for the U.S. Department of Energy (DOE) by Sandia Corporation, a subsidiary of the Lockheed Martin Company. SNL/NM is located on land controlled by DOE within the boundaries of Kirtland Air Force Base (KAFB) in Albuquerque, New Mexico. The major responsibilities of SNL/NM are the support of national security and energy projects. This report provides an environmental assessment of proposed remedial action activities at the solid waste management units at SNL/NM. A risk assessment of health hazards is also discussed.

  19. Metallization and packaging of compound semiconductor devices at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Seigal, P.K.; Armendariz, M.G.; Rieger, D.J.; Lear, K.L.; Sullivan, C.T.

    1996-11-01

    Recent advances in compound semiconductor technology utilize a variety of metal thin films fabricated by thermal and electron-beam evaporation, and electroplating. An overview of metal processes used by Sandia`s Compound Semiconductor Research Laboratory is presented. Descriptions of electrical n-type and p-type ohmic contact alloys, interconnect metal, and metal layers specifically included for packaging requirements are addressed. Several illustrations of devices incorporating gold plated air bridges are included. ``Back-end`` processes such as flip-chip under bump metallurgy with fluxless solder reflow and plated solder processes are mentioned as current research areas.

  20. Kaiser Permanente-Sandia National Health Care Model: Phase 1 prototype final report. Part 2 -- Domain analysis

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, D.; Yoshimura, A.; Butler, D.; Judson, R.; Mason, W.; Napolitano, L.; Mariano, R. [Sandia National Labs., Livermore, CA (United States); Eddy, D.; Schlessinger, L. [Kaiser Permanente, Pasadena, CA (United States)

    1996-11-01

    This report describes the results of a Cooperative Research and Development Agreement between Sandia National Laboratories and Kaiser Permanente Southern California to develop a prototype computer model of Kaiser Permanente`s health care delivery system. As a discrete event simulation, SimHCO models for each of 100,000 patients the progression of disease, individual resource usage, and patient choices in a competitive environment. SimHCO is implemented in the object-oriented programming language C{sup 2}, stressing reusable knowledge and reusable software components. The versioned implementation of SimHCO showed that the object-oriented framework allows the program to grow in complexity in an incremental way. Furthermore, timing calculations showed that SimHCO runs in a reasonable time on typical workstations, and that a second phase model will scale proportionally and run within the system constraints of contemporary computer technology.

  1. 75 FR 22409 - Decision To Evaluate a Petition To Designate a Class of Employees From the Sandia National...

    Science.gov (United States)

    2010-04-28

    ... National Laboratory in Albuquerque, NM, To Be Included in the Special Exposure Cohort AGENCY: National... designate a class of employees from the Sandia National Laboratory in Albuquerque, New Mexico, to be... warranted by the evaluation, is as follows: Facility: Sandia National Laboratory. Location: Albuquerque,...

  2. 76 FR 70456 - Decision To Evaluate a Petition To Designate a Class of Employees From Sandia National Laboratory...

    Science.gov (United States)

    2011-11-14

    ... Laboratory, Albuquerque, NM, To Be Included in the Special Exposure Cohort AGENCY: National Institute for... class of employees from Sandia National Laboratory, Albuquerque, New Mexico, to be included in the... evaluation, is as follows: Facility: Sandia National Laboratory. Location: Albuquerque, New Mexico....

  3. Sandia Wake Imaging System Field Test Report: 2015 Deployment at the Scaled Wind Farm Technology (SWiFT) Facility.

    Energy Technology Data Exchange (ETDEWEB)

    Naughton, Brian Thomas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Herges, Thomas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-10-01

    This report presents the objectives, configuration, procedures, reporting , roles , and responsibilities and subsequent results for the field demonstration of the Sandia Wake Imaging System (SWIS) at the Sandia Scaled Wind Farm Technology (SWiFT) facility near Lubbock, Texas in June and July 2015.

  4. Using the Sandia Z Machine to Probe Water at Planetary Conditions: Redefining the Properties of Water in the Ice Giants

    Science.gov (United States)

    Knudson, M. D.; Desjarlais, M.; Lemke, R.; Mattsson, T.; French, M.; Nettelmann, N.; Redmer, R.

    2012-12-01

    Recently, there has been a tremendous increase in the number of identified extrasolar planetary systems. Our understanding of their formation is tied to exoplanet internal structure models, which rely upon equation of state (EOS) models of light elements and compounds such as water at multi-Mbar pressure conditions. For the past decade, a large, interdisciplinary team at Sandia National Laboratories has been refining the Z Machine (20+ MA and 10+ MGauss) into a mature, robust, and precise platform for material dynamics experiments in the multi-Mbar pressure regime. In particular, significant effort has gone into effectively coupling condensed matter theory, magneto-hydrodynamic simulation, and electromagnetic modeling to produce a fully self-consistent simulation capability able to very accurately predict the performance of the Z machine and various experimental load configurations. This capability has been instrumental in the ability to develop experimental platforms to routinely perform magnetic ramp compression experiments to over 4 Mbar, and magnetically accelerate flyer plates to over 40 km/s, creating over 20 Mbar impact pressures. Furthermore, a strong tie has been developed between the condensed matter theory and the experimental program. This coupling has been proven time and again to be extremely fruitful, with the capability of both theory and experiment being challenged and advanced through this close interrelationship. This presentation will provide a short overview of the material dynamics platform and discuss in more detail the use of Z to perform extreme material dynamics studies with unprecedented accuracy on water in support of basic science, planetary astrophysics, and the emerging field of high energy density laboratory physics. It was found that widely used EOSs for water are much too compressible (up to 30 percent) at pressures and temperatures relevant to planetary interiors. Furthermore, it is shown that the behavior of water at these

  5. Numerical techniques for electromagnetic applications in microelectronic and radar imaging systems

    Science.gov (United States)

    Akerson, Jerome J.

    1998-12-01

    In this thesis, the application of numerical techniques to electromagnetic problems in microelectronic and radar imaging systems are investigated. In particular the following problems are studied: (1) Dielectric rib waveguide discontinuities are analyzed with the Finite Difference Time Domain (FDTD) method. The application of Berenger's Perfectly Matched Layer to multi-layered dielectrics is analyzed and the specific conditions needed to successfully match the multiple dielectric layers are determined and justified. An FDTD method to find the fundamental mode's spatial distribution is used to excite the discontinuity problem. It is shown that the computational domain can be reduced by twenty percent over Gaussian excitations. The effects of rib waveguide bend discontinuities and the effects of the rib geometry to the bend loss are presented. (2) An Impedance Boundary Condition (IBC) for two dimensional FDTD simulations containing thin, good conductor sheets is developed. The IBC uses a recursive convolution scheme based on approximating the conductor's impedance as a sum of exponentials. The effects of FDTD parameters such as grid size and time step on simulation accuracy are presented. The IBC is shown to accurately model the conductor loss over a wide frequency range. The verification is performed by comparing the quality factors of rectangular resonant structures determined by the FDTD simulation and analytical methods. (3) Phase unwrapping techniques for the inversion of terrain height using Synthetic Aperture Radar Interferometry (InSAR) data are analyzed. The weighted least squares and branch cut phase unwrapping techniques are specifically studied. An optimal branch cut method and a hybrid least squares/branch cut method are presented and used to unwrap the phase of both simulated and real SAR interferograms. When used to invert terrain height, these new SAR phase unwrapping methods offer over fifty percent reduction in root mean square (rms) height error

  6. Sandia National Laboratories interactions with organizations in the Former Soviet Union

    Energy Technology Data Exchange (ETDEWEB)

    Whiting, G.H.; Nokes, K.D.

    1994-03-01

    This document describes Sandia National Laboratories involvement with scientists and engineers at various organizations within the states of the Former Soviet Union (FSU). The purpose of these interactions is twofold: first, to acquire technical information to enhance United States technology and second, to assist FSU states in converting their defense-oriented industry to civilian, market- oriented business.

  7. Radiological NESHAP Annual Report CY 2015 Sandia National Laboratories New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Evelo, Stacie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-05-01

    This report provides a summary of the radionuclide releases from the United States (U.S.) Department of Energy (DOE) National Nuclear Security Administration facilities at Sandia National Laboratories, New Mexico (SNL/NM) during Calendar Year (CY) 2015, including the data, calculations, and supporting documentation for demonstrating compliance with 40 Code of Federal Regulation (CFR) 61.

  8. Improved PV system reliability results from surge evaluations at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Russell H. Bonn; Sigifredo Gonzalez

    2000-04-11

    Electrical surges on ac and dc inverter power wiring and diagnostic cables have the potential to shorten the lifetime of power electronics. These surges may be caused by either nearby lightning or capacitor switching transients. This paper contains a description of ongoing surge evaluations of PV power electronics and surge mitigation hardware at Sandia.

  9. Sandia National Laboratories/New Mexico Environmental Baseline update--Revision 1.0

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-07-01

    This report provides a baseline update to provide the background information necessary for personnel to prepare clear and consise NEPA documentation. The environment of the Sandia National Laboratories is described in this document, including the ecology, meteorology, climatology, seismology, emissions, cultural resources and land use, visual resources, noise pollution, transportation, and socioeconomics.

  10. Large-eddy simulation/probability density function modeling of local extinction and re-ignition in Sandia Flame E

    Science.gov (United States)

    Wang, Haifeng; Popov, Pavel; Hiremath, Varun; Lantz, Steven; Viswanathan, Sharadha; Pope, Stephen

    2010-11-01

    A large-eddy simulation (LES)/probability density function (PDF) code is developed and applied to the study of local extinction and re-ignition in Sandia Flame E. The modified Curl mixing model is used to account for the sub-filter scalar mixing; the ARM1 mechanism is used for the chemical reaction; and the in- situ adaptive tabulation (ISAT) algorithm is used to accelerate the chemistry calculations. Calculations are performed on different grids to study the resolution requirement for this flame. Then, with sufficient grid resolution, full-scale LES/PDF calculations are performed to study the flame characteristics and the turbulence-chemistry interactions. Sensitivity to the mixing frequency model is explored in order to understand the behavior of sub-filter scalar mixing in the context of LES. The simulation results are compared to the experimental data to demonstrate the capability of the code. Comparison is also made to previous RANS/PDF simulations.

  11. The Los Alamos, Sandia, and Livermore Laboratories: Integration and collaboration solving science and technology problems for the nation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-01

    More than 40 years ago, three laboratories were established to take on scientific responsibility for the nation`s nuclear weapons - Los Alamos, Sandia, and Livermore. This triad of laboratories has provided the state-of-the-art science and technology to create America`s nuclear deterrent and to ensure that the weapons are safe, secure, and to ensure that the weapons are safe, secure, and reliable. These national security laboratories carried out their responsibilities through intense efforts involving almost every field of science, engineering, and technology. Today, they are recognized as three of the world`s premier research and development laboratories. This report sketches the history of the laboratories and their evolution to an integrated three-laboratory system. The characteristics that make them unique are described and some of the major contributions they have made over the years are highlighted.

  12. From Idea to Innovation: The Role of LDRD Investments in Sandia's Recent Successful B61 Experiments.

    Energy Technology Data Exchange (ETDEWEB)

    Arrowsmith, Marie Danielle [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-11-01

    The Laboratory Directed Research and Development (LDRD) program, authorized by U.S. Congress in 1991, enables Department of Energy (DOE) laboratories to devote a small portion of their research funding to high-risk and potentially high-payoff research. Because it is high-risk, LDRD-supported research may not lead to immediate mission impacts; however, many successes at DOE labs can be traced back to investments in LDRD. LDRD investments have a history of enabling significant payoffs for long-running DOE and NNSA missions and for providing anticipatory new technologies that ultimately become critical to future missions. Many of Sandia National Laboratories’ successes can be traced back to investments in LDRD. Capabilities from three LDRDs were critical to recent tests of the B61-12 gravity bomb—tests that would previously have only been performed experimentally.

  13. The high current, fast, 100ns, Linear Transformer Driver (LTD) developmental project at Sandia Laboratories and HCEI.

    Energy Technology Data Exchange (ETDEWEB)

    Ward, Kevin S. (Ketech Corporation, Albuquerque, NM); Long, Finis W.; Sinebryukhov, Vadim A. (High Current Electronic Institute (HCEI), Tomsk, Russia); Kim, Alexandre A. (High Current Electronic Institute (HCEI), Tomsk, Russia); Wakeland, Peter Eric (Ketech Corporation, Albuquerque, NM); McKee, G. Randall; Woodworth, Joseph Ray; McDaniel, Dillon Heirman; Fowler, William E.; Mazarakis, Michael Gerrassimos; Porter, John Larry, Jr.; Struve, Kenneth William; Savage, Mark Edward; Stygar, William A.; LeChien, Keith R.; Matzen, Maurice Keith

    2010-09-01

    Sandia National Laboratories, Albuquerque, N.M., USA, in collaboration with the High Current Electronic Institute (HCEI), Tomsk, Russia, is developing a new paradigm in pulsed power technology: the Linear Transformer Driver (LTD) technology. This technological approach can provide very compact devices that can deliver very fast high current and high voltage pulses straight out of the cavity with out any complicated pulse forming and pulse compression network. Through multistage inductively insulated voltage adders, the output pulse, increased in voltage amplitude, can be applied directly to the load. The load may be a vacuum electron diode, a z-pinch wire array, a gas puff, a liner, an isentropic compression load (ICE) to study material behavior under very high magnetic fields, or a fusion energy (IFE) target. This is because the output pulse rise time and width can be easily tailored to the specific application needs. In this paper we briefly summarize the developmental work done in Sandia and HCEI during the last few years, and describe our new MYKONOS Sandia High Current LTD Laboratory. An extensive evaluation of the LTD technology is being performed at SNL and the High Current Electronic Institute (HCEI) in Tomsk Russia. Two types of High Current LTD cavities (LTD I-II, and 1-MA LTD) were constructed and tested individually and in a voltage adder configuration (1-MA cavity only). All cavities performed remarkably well and the experimental results are in full agreement with analytical and numerical calculation predictions. A two-cavity voltage adder is been assembled and currently undergoes evaluation. This is the first step towards the completion of the 10-cavity, 1-TW module. This MYKONOS voltage adder will be the first ever IVA built with a transmission line insulated with deionized water. The LTD II cavity renamed LTD III will serve as a test bed for evaluating a number of different types of switches, resistors, alternative capacitor configurations, cores

  14. Microelectronics technologies for new detectors in medical imaging

    CERN Document Server

    Heijne, Erik H M

    2007-01-01

    The use of silicon chips for instrumentation developments in elementary particle physics serves as an example for other applications and digital imaging detectors could find use in medical and molecular imaging. Attractive features are direct quantum conversion in a semiconductor matrix, innovative three-dimensional modular detector construction, multilayer devices, very fast signal processing, on-line data pre-processing and massive parallelism at the system level. Cost aspects of such semiconductor imager options have to be taken into account in the R&D phase. With the integrated electronics and high density interconnects in the Medipix development as an example, the ultimate aim of single photon imaging comes within reach.

  15. Complex VLSI Feature Comparison for Commercial Microelectronics Verification

    Science.gov (United States)

    2014-03-27

    verification of untrusted circuits using industry-standard and custom software. The process developed under TRUST and implemented at the AFRL Mixed Signal...79 5.2.3 SCR and Other Netlists . . . . . . . . . . . . . . . . . . . . . . . . 79 5.2.4 Additional Tools...Reliability of Integrated Circuits LVS layout versus schematic MOSIS the Metal Oxide Semiconductor Implementation Service MSDC Mixed Signal Design

  16. Implementing the Corrective Action Management Unit at Sandia National Laboratories, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    MOORE,DARLENE R.; SCHRADER,SCOTT A.; KING,GABRIEL G.; CORMIER,JOHN

    2000-01-26

    In September 1997, following significant public and regulator interaction, Sandia Corporation (Sandia) was granted a Resource Conservation and Recovery Act (RCRA) and Hazardous Solid Waste Amendment (HSWA) permit modification allowing construction and operation of a Correction Action Management Unit (CAMU). The CAMU follows recent regulatory guidance that allows for cost-effective, expedient cleanup of contaminated sites and management of hazardous remediation wastes. The CAMU was designed to store, treat, and provide long-term management for Environmental Restoration (ER) derived wastes. The 154 square meter CAMU site at Sandia National Laboratories, New Mexico (SNL/NM), includes facilities for storing bulk soils and containerized wastes, for treatment of bulk soils, and has a containment cell for long-term disposition of waste. Proposed treatment operations include soil washing and low temperature thermal desorption. The first waste was accepted into the CAMU for temporary storage in January 1999. Construction at the CAMU was completed in March 1999, and baseline monitoring of the containment cell has commenced. At completion of operations the facility will be closed, the waste containment cell will be covered, and long-term post-closure monitoring will begin. Sandia's CAMU is the only such facility within the US Department of Energy (DOE) complex. Implementing this innovative approach to ER waste management has required successful coordination with community representatives, state and federal regulators, the DOE, Sandia corporate management, and contractors. It is expected that cost savings to taxpayers will be significant. The life-cycle CAMU project cost is currently projected to be approximately $12 million.

  17. Recovery energy from ship propulsion system based on microelectronic technology

    Science.gov (United States)

    Iordanoaia, F.; Nicorescu, M.

    2009-01-01

    All shipping companies are involved in the several management programs for increasing of efficiency of transportation on the sea. Optimal transportation is one of actual tendency in the world shipbuilding which requests a lot of human resources in design development respectively in construction of the ships. One direction with very good results is to use one part of propulsion energy for electrical power generating on board with multiple technical and economical advantages. Based on this, more resources in research and design are encouraged by development projects in order to increase the efficiency of described system. Even if, power-generating plant is one of classic ship mecatronics system, it must to be continuously perfected in the way of decreasing of specific fuel consumption as well in the increasing of the friableness and endurance.

  18. Computational Modeling as a Design Tool in Microelectronics Manufacturing

    Science.gov (United States)

    Meyyappan, Meyya; Arnold, James O. (Technical Monitor)

    1997-01-01

    Plans to introduce pilot lines or fabs for 300 mm processing are in progress. The IC technology is simultaneously moving towards 0.25/0.18 micron. The convergence of these two trends places unprecedented stringent demands on processes and equipments. More than ever, computational modeling is called upon to play a complementary role in equipment and process design. The pace in hardware/process development needs a matching pace in software development: an aggressive move towards developing "virtual reactors" is desirable and essential to reduce design cycle and costs. This goal has three elements: reactor scale model, feature level model, and database of physical/chemical properties. With these elements coupled, the complete model should function as a design aid in a CAD environment. This talk would aim at the description of various elements. At the reactor level, continuum, DSMC(or particle) and hybrid models will be discussed and compared using examples of plasma and thermal process simulations. In microtopography evolution, approaches such as level set methods compete with conventional geometric models. Regardless of the approach, the reliance on empricism is to be eliminated through coupling to reactor model and computational surface science. This coupling poses challenging issues of orders of magnitude variation in length and time scales. Finally, database development has fallen behind; current situation is rapidly aggravated by the ever newer chemistries emerging to meet process metrics. The virtual reactor would be a useless concept without an accompanying reliable database that consists of: thermal reaction pathways and rate constants, electron-molecule cross sections, thermochemical properties, transport properties, and finally, surface data on the interaction of radicals, atoms and ions with various surfaces. Large scale computational chemistry efforts are critical as experiments alone cannot meet database needs due to the difficulties associated with such

  19. Radiation effects on microelectronics and future space missions

    Science.gov (United States)

    Patterson, Jeffrey D.

    2003-01-01

    This paper briefly reviews the three basic radiation effect mechanisms, and how they interrupt the functionality of currently available non-volatile memory technologies. This paper also presents a very general overview of the radiation environments expected in future space exploration missions. Unfortunately, these environments will be very harsh, from a radiation standpoint, and thus a significant effort is required to develop non-volatile technologies that will meet future mission requirements.

  20. Reliability of Small Geometry VLSI Devices for Microelectronics

    Science.gov (United States)

    1992-02-15

    Trap Pocie - Average Energy Field Frenkel Kinetic Barrier Energy Lowerng F g. 18 Formulaticn of the Energy Eaiance Equation for the Fc: E’ectron Cacture...equipped w/color monitors . and a SPARC Station SLC. V Fig. 2 SUN SPARC I Workstations Fig, 3, illustrates a CMOS test vehicle with micrometer...processing. Custom built pattern generator and threshold detect circuitry, seen in Fig. 16. is used to monitor developments in our non-volatile memory

  1. The Sandia GeoModel : theory and user's guide.

    Energy Technology Data Exchange (ETDEWEB)

    Brannon, Rebecca Moss; Fossum, Arlo Frederick

    2004-08-01

    The mathematical and physical foundations and domain of applicability of Sandia's GeoModel are presented along with descriptions of the source code and user instructions. The model is designed to be used in conventional finite element architectures, and (to date) it has been installed in five host codes without requiring customizing the model subroutines for any of these different installations. Although developed for application to geological materials, the GeoModel actually applies to a much broader class of materials, including rock-like engineered materials (such as concretes and ceramics) and even to metals when simplified parameters are used. Nonlinear elasticity is supported through an empirically fitted function that has been found to be well-suited to a wide variety of materials. Fundamentally, the GeoModel is a generalized plasticity model. As such, it includes a yield surface, but the term 'yield' is generalized to include any form of inelastic material response including microcrack growth and pore collapse. The geomodel supports deformation-induced anisotropy in a limited capacity through kinematic hardening (in which the initially isotropic yield surface is permitted to translate in deviatoric stress space to model Bauschinger effects). Aside from kinematic hardening, however, the governing equations are otherwise isotropic. The GeoModel is a genuine unification and generalization of simpler models. The GeoModel can employ up to 40 material input and control parameters in the rare case when all features are used. Simpler idealizations (such as linear elasticity, or Von Mises yield, or Mohr-Coulomb failure) can be replicated by simply using fewer parameters. For high-strain-rate applications, the GeoModel supports rate dependence through an overstress model.

  2. Listening to Brain Microcircuits for Interfacing With External World—Progress in Wireless Implantable Microelectronic Neuroengineering Devices

    Science.gov (United States)

    Nurmikko, Arto V.; Donoghue, John P.; Hochberg, Leigh R.; Patterson, William R.; Song, Yoon-Kyu; Bull, Christopher W.; Borton, David A.; Laiwalla, Farah; Park, Sunmee; Ming, Yin; Aceros, Juan

    2011-01-01

    Acquiring neural signals at high spatial and temporal resolution directly from brain microcircuits and decoding their activity to interpret commands and/or prior planning activity, such as motion of an arm or a leg, is a prime goal of modern neurotechnology. Its practical aims include assistive devices for subjects whose normal neural information pathways are not functioning due to physical damage or disease. On the fundamental side, researchers are striving to decipher the code of multiple neural microcircuits which collectively make up nature’s amazing computing machine, the brain. By implanting biocompatible neural sensor probes directly into the brain, in the form of microelectrode arrays, it is now possible to extract information from interacting populations of neural cells with spatial and temporal resolution at the single cell level. With parallel advances in application of statistical and mathematical techniques tools for deciphering the neural code, extracted populations or correlated neurons, significant understanding has been achieved of those brain commands that control, e.g., the motion of an arm in a primate (monkey or a human subject). These developments are accelerating the work on neural prosthetics where brain derived signals may be employed to bypass, e.g., an injured spinal cord. One key element in achieving the goals for practical and versatile neural prostheses is the development of fully implantable wireless microelectronic “brain-interfaces” within the body, a point of special emphasis of this paper. PMID:21654935

  3. The planar silicon-based microelectronic technology for electrochemical transducers

    Science.gov (United States)

    Novikov, A. V.; Egorchikov, A. E.; Dolgov, A. N.; Gornev, E. S.; Popov, V. G.; Egorov, I. V.; Krishtop, V. G.

    2016-12-01

    We have developed the new technology for production of sensitive modules for electrochemical sensors of pressure and acceleration. The technology is applicable for mass production and scalable for high-volume production. In this work we demonstrate the new sensing module for electrochemical motion sensors, and its possibility of applying in geophones. We fabricated prototypes of electrochemical planar transducer chips, produced a laboratory prototype of a geophone based on our planar transducer chip, and tested them. This paper presents the preliminary results of the tests.

  4. AN AUTOMATIC TEST ENVIRONMENT FOR MICROELECTRONICS EDUCATION AND RESEARCH

    Directory of Open Access Journals (Sweden)

    Federico Sandoval-Ibarra

    2008-04-01

    Full Text Available An automatic test environment (ATE based on a PSoC has been developed to perform electricalcharacterization of integrated circuits (ICs. The ICs are designed for academic and research purposesas part of the Electronic Design graduate program at CINVESTAV-Guadalajara Unit; these ICs aremanufactured in standard N-well, 5-V, 1.5μm/0.5μm CMOS technologies. The ATE offers programmablecapabilities to develop master-slave architectures, memory for data storage, functions generator tostimulate circuits and systems, current/voltage sources for several purposes, current-voltagemeasurements, and ports to download experimental data to a PC. To date, several ICs have been testedwith the help of the ATE. In this paper, however, examples based on MOS Transistors only arepresented in order to describe the ATE performance and also to show how experimental data of thedevices under characterization were validated through SPICE simulations, experimental data given bymanufacturers, and using commercial equipment as well.

  5. Cure behavior of epoxy polymers used in microelectronics

    Science.gov (United States)

    Taweeplengsangsuke, Jantrawan

    2000-10-01

    Underfill resins are used to reduce solder fatigue in flip-chip assemblies. Both underfilling and curing processes are critical to achieve reliable finished products. This study included two main themes; the development of processing diagrams for commercial underfill resins and the fundamental understanding of cure kinetics and evolution of cure stresses in model epoxies. A variety of techniques have been used to characterize the fundamental phenomena involved in the processing of underfill resins. The flow behavior, cure kinetics, cure stresses, outgassing phenomena and void formation of underfill resins were studied. Processing diagrams for underfill resins were developed by mapping fundamental phenomena involved to provide a guideline for underfilling and curing steps. With these processing diagrams one should be able to design his underfilling and curing process with scientific approach. Two commercial underfill resins, which were evaluated as part of a SEMATECH program, where shown to possess significantly different processing characteristics. However, the appropriate explanation could not be made without knowing the proprietary chemistry of the systems. Therefore, model epoxies were formulated. Three different systems were investigated; amine, imidazole, and anhydride curing agent systems. With the known chemistry, the reaction kinetics and developed cure stress can be explained more clearly. Vitrification, which severely retards the rate of reaction, was found in amine (N-aminoethylpiperazine) and anhydride (Hexahydro-4-methylphthalic anhydride) cured systems when the cure temperatures were lower than the glass transition temperature (T g) of fully cured samples; however, imidazole(2-ethyl-4-methyl-imidazole) did not show vitrification when it was cured at 20 degrees below the T g of fully cured sample due to the large exotherms. Interestingly for imidazole system, the higher cure temperature exhibited a lower Tg. This could possibly be explained by the

  6. Synthetic Jets for Heat Transfer Augmentation in Microelectronics Systems

    Science.gov (United States)

    Arik, Mehmet; Tamdogan, Enes

    Rapid progress in science and information technology, growing manufacturing activities and increase in globalization have boosted the demand for advanced electronics devices. Moreover, increase in microprocessor power dissipation coupled with the reduction in feature sizes due to manufacturing process improvements have resulted in continuously increasing heat fluxes. Thus, ever increasing heat fluxes have required the development of novel, reliable and affordable thermal management technologies. Although some of those proposed solutions for high flux cooling problems based on liquid cooling methods such as spray and evaporative cooling; air cooling is still commonly preferred due to its availability, reliability, easiness and low cost. Therefore, over the last decade microfluidics devices such as synthetic jets have been investigated as an alternative to conventional air moving devices, and have been shown as highly effective for cooling of electronics in compact thermal real estates...

  7. PRECISION MOTION SYSTEM FOR OPTO-MECHANICAL EQUIPMENT OF MICROELECTRONICS

    Directory of Open Access Journals (Sweden)

    I. V. Dainiak

    2015-01-01

    Full Text Available The paper proposes a structure of precision motion system built on the basis of a circular multi-coordinate synchronous segment motor and reconfigurable parallel kinematic mechanism. The multi-coordinate synchronous segment motor may have from two to six movable segments depending on the design, and number of the segments generally defines an internal mobility of the motor. A specific feature of the parallel kinematic mechanism consists in the possibility of its structure reconfiguration by serial connection of two neighboring rods with the help of free elements of their spherical joints into triangular circuits with one spherical hinge at the common vertex. As result of this, the controlled motion of motor movable segments is transformed into the complex spatial displacement of circular platform with number of degrees of freedom up to six inclusively.A mathematical model for solution of the kinematic problem in the investigated parallel mechanism has been offered in the paper. The model allows to calculate a position of movable segments of multi-coordinate synchronous motor depending on the desired position and orientation of the executive circular platform. The parametric definition of base point positions in the motor segments in time allows eventually to form algorithms of programmable motions.The paper substantiates ability to embed the developed motion system into projection unit of opto-mechanical equipment while preserving traditional configuration scheme. This provides the possibility of adaptive adjustment of optical elements during operation; it allows to adjust the optical elements when the geometry of projection system is changed due to deterioration. As result, main characteristics of projection system: resolution, depth of field and image contrast and distortion are maintained at the required level. The developed motion system can be used as a coordinate system of positioning, alignment and scanning in the assembly and other

  8. Multi-scale radiographic applications in microelectronic industry

    Science.gov (United States)

    Gluch, J.; Löffler, M.; Meyendorf, N.; Oppermann, M.; Röllig, M.; Sättler, P.; Wolter, K. J.; Zschech, E.

    2016-02-01

    New concepts in assembly technology boost our daily life in an unknown way. High end semiconductor industry today deals with functional structures down to a few nanometers. ITRS roadmap predicts an ongoing decrease of the "DRAM half pitch" over the next decade. Packaging of course is not intended to realize pitches at the nanometer scale, but has to face the challenges of integrating such semiconductor devices with smallest pitch and high pin counts into systems. System integration (SiP, SoP, Hetero System Integration etc.) into the third dimension is the only way to reduce the gap between semiconductor level and packaging level interconnection. The described development is mainly driven by communication technology but also other branches like power electronics benefit from the vast progress in integration and assembly technology. The challenge of advanced packaging requires new nondestructive evaluation (NDE) techniques for technology development and production control. In power electronics production the condition monitoring receives a lot of interest to avoid electrical shortcuts, dead solder joints and interface cracking. It is also desired to detect and characterize very small defects like transportation phenomenon or Kirkendall voids. For this purpose imaging technologies with resolutions in the sub-micron range are required. Our presentation discusses the potentials and the limits of X-ray NDE techniques, illustrated by crack observation in solder joints, evaluation of micro vias in PCBs and interposers and the investigation of solder material composition and other aftermaths of electro migration in solder joints. Applied radiographic methods are X-ray through transmission, multi-energy techniques, laminography, CT and nano-CT.

  9. 2013 Annual Site Environmental Report for Sandia National Laboratories Tonopah Test Range Nevada & Kauai Test Facility Hawaii

    Energy Technology Data Exchange (ETDEWEB)

    Griffith, Stacy Rene [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Agogino, Karen [National Nuclear Security Administration (NNSA), Washington, DC (United States); Li, Jun [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); White, Nancy [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Minitrez, Alexandra [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Avery, Penny [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Bailey-White, Brenda [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Bonaguidi, Joseph [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Catechis, Christopher [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); duMond, Michael [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Eckstein, Joanna [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Evelo, Stacie [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Forston, William [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Herring, III, Allen [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Lantow, Tiffany [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Martinez, Reuben [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Mauser, Joseph [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Miller, Amy [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Miller, Mark [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Payne, Jennifer [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Peek, Dennis [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Reiser, Anita [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Ricketson, Sherry [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Roma, Charles [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Salinas, Stephanie [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Ullrich, Rebecca [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2014-08-01

    Tonopah Test Range (TTR) in Nevada and Kauai Test Facility (KTF) in Hawaii are government-owned, contractor-operated facilities managed and operated by Sandia Corporation (Sandia), a wholly owned subsidiary of Lockheed Martin Corporation. The U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA), through the Sandia Field Office (SFO), in Albuquerque, New Mexico, administers the contract and oversees contractor operations at TTR and KTF. Sandia manages and conducts operations at TTR in support of the DOE/NNSA’s Weapons Ordnance Program and has operated the site since 1957. Navarro Research and Engineering subcontracts to Sandia in administering most of the environmental programs at TTR. Sandia operates KTF as a rocket preparation launching and tracking facility. This Annual Site Environmental Report summarizes data and the compliance status of the sustainability, environmental protection, and monitoring program at TTR and KTF through Calendar Year 2013. The compliance status of environmental regulations applicable at these sites include state and federal regulations governing air emissions, wastewater effluent, waste management, terrestrial surveillance, Environmental Restoration (ER) cleanup activities, and the National Environmental Policy Act. Sandia is responsible only for those environmental program activities related to its operations. The DOE/NNSA/Nevada Field Office retains responsibility for the cleanup and management of TTR ER sites. Environmental monitoring and surveillance programs are required by DOE Order 231.1B, Environment, Safety, and Health Reporting (DOE 2012).

  10. United States Department of Energy National Nuclear Security Administration Sandia Field Office NESHAP Annual Report CY2014 for Sandia National Laboratories New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    evelo, stacie [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Miller, Mark L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-05-01

    This report provides a summary of the radionuclide releases from the United States (U.S.) Department of Energy (DOE) National Nuclear Security Administration facilities at Sandia National Laboratories, New Mexico (SNL/NM) during Calendar Year (CY) 2014, including the data, calculations, and supporting documentation for demonstrating compliance with 40 Code of Federal Regulation (CFR) 61, Subpart H--NATIONAL EMISSION STANDARDS FOR EMISSIONS OF RADIONUCLIDES OTHER THAN RADON FROM DEPARTMENT OF ENERGY FACILITIES. A description is given of the sources and their contributions to the overall dose assessment. In addition, the maximally exposed individual (MEI) radiological dose calculation and the population dose to local and regional residents are discussed.

  11. Circuit design of VLSI for microelectronic coordinate-sensitive detector for material element analysis

    Directory of Open Access Journals (Sweden)

    Sidorenko V. P.

    2012-08-01

    Full Text Available There has been designed, manufactured and tested a VLSI providing as a part of the microelectronic coordinate-sensitive detector the simultaneous elemental analysis of all the principles of the substance. VLSI ensures the amplifier-converter response on receiving of 1,6.10–13 С negative charge to its input. Response speed of the microcircuit is at least 3 MHz in the counting mode and more than 4 MHz in the counter information read-out mode. The power consumption of the microcircuit is no more than 7 mA.

  12. Eye vision system using programmable micro-optics and micro-electronics

    Science.gov (United States)

    Riza, Nabeel A.; Amin, M. Junaid; Riza, Mehdi N.

    2014-02-01

    Proposed is a novel eye vision system that combines the use of advanced micro-optic and microelectronic technologies that includes programmable micro-optic devices, pico-projectors, Radio Frequency (RF) and optical wireless communication and control links, energy harvesting and storage devices and remote wireless energy transfer capabilities. This portable light weight system can measure eye refractive powers, optimize light conditions for the eye under test, conduct color-blindness tests, and implement eye strain relief and eye muscle exercises via time sequenced imaging. Described is the basic design of the proposed system and its first stage system experimental results for vision spherical lens refractive error correction.

  13. Application of multivariate statistical analysis to STEM X-ray spectral images: interfacial analysis in microelectronics.

    Science.gov (United States)

    Kotula, Paul G; Keenan, Michael R

    2006-12-01

    Multivariate statistical analysis methods have been applied to scanning transmission electron microscopy (STEM) energy-dispersive X-ray spectral images. The particular application of the multivariate curve resolution (MCR) technique provides a high spectral contrast view of the raw spectral image. The power of this approach is demonstrated with a microelectronics failure analysis. Specifically, an unexpected component describing a chemical contaminant was found, as well as a component consistent with a foil thickness change associated with the focused ion beam specimen preparation process. The MCR solution is compared with a conventional analysis of the same spectral image data set.

  14. Configurations of high-frequency ultrasonics complex vibration systems for packaging in microelectronics.

    Science.gov (United States)

    Tsujino, Jiromaru; Harada, Yoshiki; Ihara, Shigeru; Kasahara, Kohei; Shimizu, Masanori; Ueoka, Tetsugi

    2004-04-01

    Ultrasonic high-frequency complex vibrations are effective for various ultrasonic high-power applications. Three types of ultrasonic complex vibration system with a welding tip vibrating elliptical to circular locus for packaging in microelectronics were studied. The complex vibration sources are using (1) a longitudinal-torsional vibration converter with diagonal slits that is driven only by a longitudinal vibration source, (2) a complex transverse vibration rod with several stepped parts that is driven by two longitudinal vibration source crossed at a right angle and (3) a longitudinal vibration circular disk and three longitudinal transducers that are installed at the circumference of the disk.

  15. Nano-interconnection for microelectronics and polymers with benzo-triazole

    Science.gov (United States)

    Park, Yeonjoon; Choi, Sang H.; Noh, Hyunpil; Kuk, Young

    2006-01-01

    Benzo-Triazole (BTA) is considered as an important bridging material that can connect an organic polymer to the metal electrode on silicon wafers as a part of the microelectronics fabrication technology. We report a detailed process of surface induced 3-D polymerization of BTA on the Cu electrode material which was measured with the Ultraviolet Photoemission Spectroscopy (UPS), X-ray Photoemission Spectroscopy (XPS), and Scanning Tunneling Microscope (STM). The electric utilization of shield and chain polymerization of BTA on Cu surface is contemplated in this study.

  16. Fundamental Studies of the Mechanical Behavior of Microelectronic Thin Film Materials

    Science.gov (United States)

    1991-01-01

    Si I-xGex Strained Layers (D.B.Noble) ................................................ 55 I. Oral Presentations Resulting from AFOSR Grants No. 89-0185...120 8 7 0 100 6 4 60 80 , E 60 0 F. ac sorption D - 21 - A desorption ( Vih ) Q 1 I - I - - a- 1 -10 0 10 20 30 40 annealing time (min) Fig. 8 D...III. ORAL PRESENTATIONS RESULTING FROM AFOSR GRANTS NO. 86- 0051 AND 86-0051 1. W.DhjX, "Mechanical Properties of Microelectronic Thin Film Materials

  17. Space Radiation Environment Prediction for VLSI microelectronics devices onboard a LEO Satellite using OMERE-Trad Software

    Science.gov (United States)

    Sajid, Muhammad

    This tutorial/survey paper presents the assessment/determination of level of hazard/threat to emerging microelectronics devices in Low Earth Orbit (LEO) space radiation environment with perigee at 300 Km, apogee at 600Km altitude having different orbital inclinations to predict the reliability of onboard Bulk Built-In Current Sensor (BBICS) fabricated in 350nm technology node at OptMA Lab. UFMG Brazil. In this context, the various parameters for space radiation environment have been analyzed to characterize the ionizing radiation environment effects on proposed BBICS. The Space radiation environment has been modeled in the form of particles trapped in Van-Allen radiation belts(RBs), Energetic Solar Particles Events (ESPE) and Galactic Cosmic Rays (GCR) where as its potential effects on Device- Under-Test (DUT) has been predicted in terms of Total Ionizing Dose (TID), Single-Event Effects (SEE) and Displacement Damage Dose (DDD). Finally, the required mitigation techniques including necessary shielding requirements to avoid undesirable effects of radiation environment at device level has been estimated /determined with assumed standard thickness of Aluminum shielding. In order to evaluate space radiation environment and analyze energetic particles effects on BBICS, OMERE toolkit developed by TRAD was utilized.

  18. Fundamental studies of tin whiskering in microelectronics finishes

    Science.gov (United States)

    Pinol, Lesly Agnes

    Common electronics materials, such as tin, copper, steel, and brass, are ambient reactive under common use conditions, and as such are prone to corrosion. During the early 1940s, reports of failures due to electrical shorting of components caused by 'whisker' (i.e., filamentary surface protrusion) growth on many surface types---including the aforementioned metals---began to emerge. Lead alloying of tin (3--10% by weight, typically in the eutectic proportion) eliminated whiskering risk for decades, until the July 2006 adoption of the Restriction of Hazardous Substances (RoHS) directive was issued by the European Union. This directive, which has since been adopted by California and parts of China, severely restricted the use of lead (market, imposing the need for developing reliable new "lead-free" alternatives to SnPb. In spite of the abundance of modern-day anecdotes chronicling whisker-related failures in satellites, nuclear power stations, missiles, pacemakers, and spacecraft navigation equipment, pure tin finishes are still increasingly being employed today, and the root cause(s) of tin whiskering remains elusive. This work describes a series of structured experiments exploring the fundamental relationships between the incidence of tin whiskering (as dependent variable) and numerous independent variables. These variables included deposition method (electroplating, electroless plating, template-based electrochemical synthesis, and various physical vapor deposition techniques, including resistive evaporation, electron beam evaporation, and sputtering), the inclusion of microparticles and organic contamination, the effects of sample geometry, and nanostructuring. Key findings pertain to correlations between sample geometry and whisker propensity, and also to the stress evolution across a series of 4"-diameter silicon wafers of varying thicknesses with respect to the degree of post-metallization whiskering. Regarding sample geometry, it was found that smaller

  19. Sandia National Laboratories, Tonopah Test Range Assembly Building 9B (Building 09-54): Photographs and Written Historical and Descriptive Data

    Energy Technology Data Exchange (ETDEWEB)

    Ullrich, Rebecca A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Corporate Archives and History Program

    2017-08-01

    Assembly Building 9B (Building 09-54) is a contributing element to the Sandia National Laboratories (SNL) Tonopah Test Range (TTR) Historic District. The SNL TTR Historic District played a significant role in U.S. Cold War history in the areas of stockpile surveillance and non-nuclear field testing of nuclear weapons designs. The district covers approximately 179,200 acres and illustrates Cold War development testing of nuclear weapons components and systems. This report includes historical information, architectural information, sources of information, project information, maps, blueprints, and photographs.

  20. Microelectronic neural bridge for signal regeneration and function rebuilding over two separate nerves

    Energy Technology Data Exchange (ETDEWEB)

    Shen Xiaoyan; Wang Zhigong; Xie Shushan; Huang Zonghao [Institute of RF- and OE-ICs, Southeast University, Nanjing 210096 (China); Lue Xiaoying, E-mail: zgwang@seu.edu.cn [Key Laboratory of Bioelectronics, Southeast University, Nanjing 210096 (China)

    2011-06-15

    According to the feature of neural signals, a micro-electronic neural bridge (MENB) has been designed. It consists of two electrode arrays for neural signal detection and functional electrical stimulation (FES), and a microelectronic circuit for signal amplifying, processing, and FES driving. The core of the system is realized in 0.5-{mu}m CMOS technology and used in animal experiments. A special experimental strategy has been designed to demonstrate the feasibility of the system. With the help of the MENB, the withdrawal reflex function of the left/right leg of one spinal toad has been rebuilt in the corresponding leg of another spinal toad. According to the coherence analysis between the source and regenerated neural signals, the controlled spinal toad's sciatic nerve signal is delayed by 0.72 ms in relation to the sciatic nerve signal of the source spinal toad and the cross-correlation function reaches a value of 0.73. This shows that the regenerated signal is correlated with the source sciatic signal significantly and the neural activities involved in reflex function have been regenerated. The experiment demonstrates that the MENB is useful in rebuilding the neural function between nerves of different bodies. (semiconductor integrated circuits)