WorldWideScience

Sample records for sand thermal conductivity

  1. Experimental and numerical study on thermal conductivity of partially saturated unconsolidated sands

    Science.gov (United States)

    Lee, Youngmin; Keehm, Youngseuk; Kim, Seong-Kyun; Shin, Sang Ho

    2016-04-01

    A class of problems in heat flow applications requires an understanding of how water saturation affects thermal conductivity in the shallow subsurface. We conducted a series of experiments using a sand box to evaluate thermal conductivity (TC) of partially saturated unconsolidated sands under varying water saturation (Sw). We first saturated sands fully with water and varied water saturation by drainage through the bottom of the sand box. Five water-content sensors were integrated vertically into the sand box to monitor water saturation changes and a needle probe was embedded to measure thermal conductivity of partially saturated sands. The experimental result showed that thermal conductivity decreases from 2.5 W/mK for fully saturated sands to 0.7 W/mK when water saturation is 5%. We found that the decreasing trend is quite non-linear: highly sensitive at very high and low water saturations. However, the boundary effects on the top and the bottom of the sand box seemed to be responsible for this high nonlinearity. We also found that the determination of water saturation is quite important: the saturation by averaging values from all five sensors and that from the sensor at the center position, showed quite different trends in the TC-Sw domain. In parallel, we conducted a pore-scale numerical modeling, which consists of the steady-state two-phase Lattice-Boltzmann simulator and FEM thermal conduction simulator on digital pore geometry of sand aggregation. The simulation results showed a monotonous decreasing trend, and are reasonably well matched with experimental data when using average water saturations. We concluded that thermal conductivity would decrease smoothly as water saturation decreases if we can exclude boundary effects. However, in dynamic conditions, i.e. imbibition or drainage, the thermal conductivity might show hysteresis, which can be investigated with pore-scale numerical modeling with unsteady-state two-phase flow simulators in our future work.

  2. The prediction model of thermal conductivity of sand-bentonite based buffer material

    Energy Technology Data Exchange (ETDEWEB)

    Tien, Y.M.; Chu, C.A. [National Central University, Dpt. of Civil Engineering, Taiwan (China); Chuangz, W.S. [Institute of Nuclear Energy Research, Atomic Energy Council, Taiwan (China)

    2005-07-01

    The thermal conductivity of sand-bentonite based buffer materials is a key factor for the design of HLW depository. In the Thermal-Hydraulic-Mechanical environment, the thermal conductivity varies due to the change in clay density, the water content, and the volumetric fraction of sand or crushed granite. In this article, an improved thermal probe method for the measurement of thermal conductivity is proposed. The probe is placed within the sand-bentonite powder inside the specially designed mold which the volume can be controlled by the position of the compacting piston. While the clay density reaches to a designated level, the measurement is executed to evaluate the thermal conductivity. With repeating the procedure, the relationship of clay dry density and the thermal conductivity can be established in one specimen. The weight water content of the bentonite is adjusted by placing in a humid chamber or in an oven for different periods. The relationship of thermal conductivity with clay dry density, water content, and sand or crushed granite is well established in this article. (authors)

  3. Thermal conductivity measurements in Porous mixtures of methane hydrate and quartz sand

    Science.gov (United States)

    Waite, W.F.; deMartin, B.J.; Kirby, S.H.; Pinkston, J.; Ruppel, C.D.

    2002-01-01

    Using von Herzen and Maxwell's needle probe method, we measured thermal conductivity in four porous mixtures of quartz sand and methane gas hydrate, with hydrate composing 0, 33, 67 and 100% of the solid volume. Thermal conductivities were measured at a constant methane pore pressure of 24.8 MPa between -20 and +15??C, and at a constant temperature of -10??C between 3.5 and 27.6 MPa methane pore pressure. Thermal conductivity decreased with increasing temperature and increased with increasing methane pore pressure. Both dependencies weakened with increasing hydrate content. Despite the high thermal conductivity of quartz relative to methane hydrate, the largest thermal conductivity was measured in the mixture containing 33% hydrate rather than in hydrate-free sand. This suggests gas hydrate enhanced grain-to-grain heat transfer, perhaps due to intergranular contact growth during hydrate synthesis. These results for gas-filled porous mixtures can help constrain thermal conductivity estimates in porous, gas hydrate-bearing systems.

  4. Investigation of Thermal Conductivity and Heat Characteristics of Oil Sands Using Ultrasound Irradiation for Shortening the Preheating Time

    Science.gov (United States)

    Kamagata, Shingo; Kawamura, Youhei; Okawa, Hirokazu; Mizutani, Koichi

    2012-07-01

    Oil sands are attractive as an energy resource. Bitumen, which is found in oil sands, has high viscosity, so that it does not flow. Most oil sands are underground and are developed with a method called steam-assisted gravity drainage (SAGD). Hot steam is injected underground to fluidize bitumen and promote its recovery. However, the preheating time is too long. One way of reducing running costs is by shortening the preheating time. Previous studies have found that bitumen can be extracted from oil sands efficiently by applying ultrasonic irradiation, but SAGD was not applied directly in these cases. Thus, the purpose of this study is to apply ultrasonic irradiation to SAGD, thereby shortening the preheating time of oil sands. As a model experiment for SAGD, heat transfer experiments in a sand layer made with Toyoura sand and silicone oil were conducted and the thermal effect with ultrasound was investigated.

  5. Thermal Properties of oil sand

    Science.gov (United States)

    LEE, Y.; Lee, H.; Kwon, Y.; Kim, J.

    2013-12-01

    Thermal recovery methods such as Cyclic Steam Injection or Steam Assisted Gravity Drainage (SAGD) are the effective methods for producing heavy oil or bitumen. In any thermal recovery methods, thermal properties (e.g., thermal conductivity, thermal diffusivity, and volumetric heat capacity) are closely related to the formation and expansion of steam chamber within a reservoir, which is key factors to control efficiency of thermal recovery. However, thermal properties of heavy oil or bitumen have not been well-studied despite their importance in thermal recovery methods. We measured thermal conductivity, thermal diffusivity, and volumetric heat capacity of 43 oil sand samples from Athabasca, Canada, using a transient thermal property measurement instrument. Thermal conductivity of 43 oil sand samples varies from 0.74 W/mK to 1.57 W/mK with the mean thermal conductivity of 1.09 W/mK. The mean thermal diffusivity is 5.7×10-7 m2/s with the minimum value of 4.2×10-7 m2/s and the maximum value of 8.0×10-7 m2/s. Volumetric heat capacity varies from 1.5×106 J/m3K to 2.11×106 J/m3K with the mean volumetric heat capacity of 1.91×106 J/m3K. In addition, physical and chemical properties (e.g., bitumen content, electric resistivity, porosity, gamma ray and so on) of oil sand samples have been measured by geophysical logging and in the laboratory. We are now proceeding to investigate the relationship between thermal properties and physical/chemical properties of oil sand.

  6. Theoretical analysis of transient heat conduction in sand

    Institute of Scientific and Technical Information of China (English)

    梁新刚; 过增元; 徐云生

    1996-01-01

    A simplified two-phase system model, with the heat transfer between phases considered, is presented and applied to the transient heat conduction in sand. The analytical results show that the one-dimensional Fourier’s law is not applicable to the transient heat conduction at very short time and there is no thermal wave described by C-V equation in sand. The two-phase system model correlates with experimental data well. Each ?phase responds to heating at different speeds in composite material, and consequently results in a temperature difference between phases. This difference will cause heat transfer between phases, which can be regarded as a heat source or sink to other phase. It is certain that Fourier’s law cannot describe the transient heat conduction in sand if a one-dimensional problem with equivalent thermal diffusivity is assumed.

  7. Thermal Properties of Foundry Mould Made of Used Green Sand

    Directory of Open Access Journals (Sweden)

    Krajewski P.K.

    2016-03-01

    Full Text Available The paper presents results of measuring heat diffusivity and thermal conductivity coefficients of used green foundry sand in temperature range ambient − 600 °C. During the experiments a technical purity Cu plate was cast into the green-sand moulds. Basing on measurements of the mould temperature field during the solidification of the casting, the temperature relationships of the measured properties were evaluated. It was confirmed that the obtained relationships are complex and that water vaporization strongly influences thermal conductivity of the moulding sand in the first period of the mould heating by the poured and solidified casting.

  8. High Temperature Thermal Properties of Bentonite Foundry Sand

    Directory of Open Access Journals (Sweden)

    Krajewski P.K.

    2015-06-01

    Full Text Available The paper presents results of measuring thermal conductivity and heat capacity of bentonite foundry sand in temperature range ambient - 900­­°C. During the experiments a technical purity Cu plate was cast into the green-sand moulds. Basing on measurements of the mould temperature field during the solidification of the casting, the temperature relationships of the measured properties were evaluated. It was confirmed that water vaporization strongly influences thermal conductivity of the moulding sand in the first period of the mould heating by the poured casting.

  9. Low thermal conductivity oxides

    Energy Technology Data Exchange (ETDEWEB)

    Pan, Wei; Phillpot, Simon R.; Wan, Chunlei; Chernatynskiy, Aleksandr; Qu, Zhixue

    2012-10-09

    Oxides hold great promise as new and improved materials for thermal-barrier coating applications. The rich variety of structures and compositions of the materials in this class, and the ease with which they can be doped, allow the exploration of various mechanisms for lowering thermal conductivity. In this article, we review recent progress in identifying specific oxides with low thermal conductivity from both theoretical and experimental perspectives. We explore the mechanisms of lowering thermal conductivity, such as introducing structural/chemical disorder, increasing material density, increasing the number of atoms in the primitive cell, and exploiting the structural anisotropy. We conclude that further systematic exploration of oxide crystal structures and chemistries are likely to result in even further improved thermal-barrier coatings.

  10. High Thermal Conductivity Materials

    CERN Document Server

    Shinde, Subhash L

    2006-01-01

    Thermal management has become a ‘hot’ field in recent years due to a need to obtain high performance levels in many devices used in such diverse areas as space science, mainframe and desktop computers, optoelectronics and even Formula One racing cars! Thermal solutions require not just taking care of very high thermal flux, but also ‘hot spots’, where the flux densities can exceed 200 W/cm2. High thermal conductivity materials play an important role in addressing thermal management issues. This volume provides readers a basic understanding of the thermal conduction mechanisms in these materials and discusses how the thermal conductivity may be related to their crystal structures as well as microstructures developed as a result of their processing history. The techniques for accurate measurement of these properties on large as well as small scales have been reviewed. Detailed information on the thermal conductivity of diverse materials including aluminum nitride (AlN), silicon carbide (SiC), diamond, a...

  11. Highly Thermal Conductive Nanocomposites

    Science.gov (United States)

    Sun, Ya-Ping (Inventor); Connell, John W. (Inventor); Veca, Lucia Monica (Inventor)

    2015-01-01

    Disclosed are methods for forming carbon-based fillers as may be utilized in forming highly thermal conductive nanocomposite materials. Formation methods include treatment of an expanded graphite with an alcohol/water mixture followed by further exfoliation of the graphite to form extremely thin carbon nanosheets that are on the order of between about 2 and about 10 nanometers in thickness. Disclosed carbon nanosheets can be functionalized and/or can be incorporated in nanocomposites with extremely high thermal conductivities. Disclosed methods and materials can prove highly valuable in many technological applications including, for instance, in formation of heat management materials for protective clothing and as may be useful in space exploration or in others that require efficient yet light-weight and flexible thermal management solutions.

  12. Thermally conductive polymers

    Science.gov (United States)

    Byrd, N. R.; Jenkins, R. K.; Lister, J. L. (Inventor)

    1971-01-01

    A thermally conductive polymer is provided having physical and chemical properties suited to use as a medium for potting electrical components. The polymer is prepared from hydroquinone, phenol, and formaldehyde, by conventional procedures employed for the preparation of phenol-formaldehyde resins. While the proportions of the monomers can be varied, a preferred polymer is formed from the monomers in a 1:1:2.4 molar or ratio of hydroquinone:phenol:formaldehyde.

  13. Thermal contact conductance

    CERN Document Server

    Madhusudana, Chakravarti V

    2013-01-01

    The work covers both theoretical and practical aspects of thermal contact conductance. The theoretical discussion focuses on heat transfer through spots, joints, and surfaces, as well as the role of interstitial materials (both planned and inadvertent). The practical discussion includes formulae and data that can be used in designing heat-transfer equipment for a variety of joints, including special geometries and configurations. All of the material has been updated to reflect the latest advances in the field.

  14. Thermal Contact Conductance

    Science.gov (United States)

    Salerno, Louis J.; Kittel, Peter

    1997-01-01

    The performance of cryogenic instruments is often a function of their operating temperature. Thus, designers of cryogenic instruments often are required to predict the operating temperature of each instrument they design. This requires accurate thermal models of cryogenic components which include the properties of the materials and assembly techniques used. When components are bolted or otherwise pressed together, a knowledge of the thermal performance of such joints are also needed. In some cases, the temperature drop across these joints represents a significant fraction of the total temperature difference between the instrument and its cooler. While extensive databases exist on the thermal properties of bulk materials, similar databases for pressed contacts do not. This has often lead to instrument designs that avoid pressed contacts or to the over-design of such joints at unnecessary expense. Although many people have made measurements of contact conductances at cryogenic temperatures, this data is often very narrow in scope and even more often it has not been published in an easily retrievable fashion, if published at all. This paper presents a summary of the limited pressed contact data available in the literature.

  15. Thermal conductivity of thermal-battery insulations

    Energy Technology Data Exchange (ETDEWEB)

    Guidotti, R.A.; Moss, M.

    1995-08-01

    The thermal conductivities of a variety of insulating materials used in thermal batteries were measured in atmospheres of argon and helium using several techniques. (Helium was used to simulate the hydrogen atmosphere that results when a Li(Si)/FeS{sub 2} thermal battery ages.) The guarded-hot-plate method was used with the Min-K insulation because of its extremely low thermal conductivity. For comparison purposes, the thermal conductivity of the Min-K insulating board was also measured using the hot-probe method. The thermal-comparator method was used for the rigid Fiberfrax board and Fiberfrax paper. The thermal conductivity of the paper was measured under several levels of compression to simulate the conditions of the insulating wrap used on the stack in a thermal battery. The results of preliminary thermal-characterization tests with several silica aerogel materials are also presented.

  16. Shape memory thermal conduction switch

    Science.gov (United States)

    Vaidyanathan, Rajan (Inventor); Krishnan, Vinu (Inventor); Notardonato, William U. (Inventor)

    2010-01-01

    A thermal conduction switch includes a thermally-conductive first member having a first thermal contacting structure for securing the first member as a stationary member to a thermally regulated body or a body requiring thermal regulation. A movable thermally-conductive second member has a second thermal contacting surface. A thermally conductive coupler is interposed between the first member and the second member for thermally coupling the first member to the second member. At least one control spring is coupled between the first member and the second member. The control spring includes a NiTiFe comprising shape memory (SM) material that provides a phase change temperature <273 K, a transformation range <40 K, and a hysteresis of <10 K. A bias spring is between the first member and the second member. At the phase change the switch provides a distance change (displacement) between first and second member by at least 1 mm, such as 2 to 4 mm.

  17. Thermal conductivity of supercooled water.

    Science.gov (United States)

    Biddle, John W; Holten, Vincent; Sengers, Jan V; Anisimov, Mikhail A

    2013-04-01

    The heat capacity of supercooled water, measured down to -37°C, shows an anomalous increase as temperature decreases. The thermal diffusivity, i.e., the ratio of the thermal conductivity and the heat capacity per unit volume, shows a decrease. These anomalies may be associated with a hypothesized liquid-liquid critical point in supercooled water below the line of homogeneous nucleation. However, while the thermal conductivity is known to diverge at the vapor-liquid critical point due to critical density fluctuations, the thermal conductivity of supercooled water, calculated as the product of thermal diffusivity and heat capacity, does not show any sign of such an anomaly. We have used mode-coupling theory to investigate the possible effect of critical fluctuations on the thermal conductivity of supercooled water and found that indeed any critical thermal-conductivity enhancement would be too small to be measurable at experimentally accessible temperatures. Moreover, the behavior of thermal conductivity can be explained by the observed anomalies of the thermodynamic properties. In particular, we show that thermal conductivity should go through a minimum when temperature is decreased, as Kumar and Stanley observed in the TIP5P model of water. We discuss physical reasons for the striking difference between the behavior of thermal conductivity in water near the vapor-liquid and liquid-liquid critical points.

  18. Thermal conductivity of boron carbides

    Science.gov (United States)

    Wood, C.; Emin, D.; Gray, P. E.

    1985-01-01

    Knowledge of the thermal conductivity of boron carbide is necessary to evaluate its potential for high-temperature thermoelectric energy conversion applications. Measurements have been conducted of the thermal diffusivity of hot-pressed boron carbide BxC samples as a function of composition (x in the range from 4 to 9), temperature (300-1700 K), and temperature cycling. These data, in concert with density and specific-heat data, yield the thermal conductivities of these materials. The results are discussed in terms of a structural model that has been previously advanced to explain the electronic transport data. Some novel mechanisms for thermal conduction are briefly discussed.

  19. THERMAL CONDUCTIVITY OF METALLIC WIRES

    Institute of Scientific and Technical Information of China (English)

    LU XIANG; GU JI-HUA; CHU JUN-HAO

    2001-01-01

    The effect of radial thickness on the thermal conductivity of a free standing wire is investigated. The thermal conductivity is evaluated using the Boltzmann equation. A simple expression for the reduction in conductivity due to the increase of boundary scattering is presented. A comparison is made between the experimental results of indium wires and the theoretical calculations. It is shown that this decrease of conductivity in wires is smaller than that in film where heat flux is perpendicular to the surface.

  20. Low Conductivity Thermal Barrier Coatings

    Science.gov (United States)

    Zhu, Dong-Ming

    2005-01-01

    Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future engine higher fuel efficiency and lower emission goals. In this presentation, thermal barrier coating development considerations and requirements will be discussed. An experimental approach is established to monitor in real time the thermal conductivity of the coating systems subjected to high-heat-flux, steady-state and cyclic temperature gradients. Advanced low conductivity thermal barrier coatings have also been developed using a multi-component defect clustering approach, and shown to have improved thermal stability. The durability and erosion resistance of low conductivity thermal barrier coatings have been improved utilizing advanced coating architecture design, composition optimization, in conjunction with more sophisticated modeling and design tools.

  1. Thermal conductivity of hydrate-bearing sediments

    Science.gov (United States)

    Cortes, Douglas D.; Martin, Ana I.; Yun, Tae Sup; Francisca, Franco M.; Santamarina, J. Carlos; Ruppel, Carolyn

    2009-11-01

    A thorough understanding of the thermal conductivity of hydrate-bearing sediments is necessary for evaluating phase transformation processes that would accompany energy production from gas hydrate deposits and for estimating regional heat flow based on the observed depth to the base of the gas hydrate stability zone. The coexistence of multiple phases (gas hydrate, liquid and gas pore fill, and solid sediment grains) and their complex spatial arrangement hinder the a priori prediction of the thermal conductivity of hydrate-bearing sediments. Previous studies have been unable to capture the full parameter space covered by variations in grain size, specific surface, degree of saturation, nature of pore filling material, and effective stress for hydrate-bearing samples. Here we report on systematic measurements of the thermal conductivity of air dry, water- and tetrohydrofuran (THF)-saturated, and THF hydrate-saturated sand and clay samples at vertical effective stress of 0.05 to 1 MPa (corresponding to depths as great as 100 m below seafloor). Results reveal that the bulk thermal conductivity of the samples in every case reflects a complex interplay among particle size, effective stress, porosity, and fluid-versus-hydrate filled pore spaces. The thermal conductivity of THF hydrate-bearing soils increases upon hydrate formation although the thermal conductivities of THF solution and THF hydrate are almost the same. Several mechanisms can contribute to this effect including cryogenic suction during hydrate crystal growth and the ensuing porosity reduction in the surrounding sediment, increased mean effective stress due to hydrate formation under zero lateral strain conditions, and decreased interface thermal impedance as grain-liquid interfaces are transformed into grain-hydrate interfaces.

  2. Thermal conductivity of hydrate-bearing sediments

    Science.gov (United States)

    Cortes, D.D.; Martin, A.I.; Yun, T.S.; Francisca, F.M.; Santamarina, J.C.; Ruppel, C.

    2009-01-01

    A thorough understanding of the thermal conductivity of hydrate-bearing sediments is necessary for evaluating phase transformation processes that would accompany energy production from gas hydrate deposits and for estimating regional heat flow based on the observed depth to the base of the gas hydrate stability zone. The coexistence of multiple phases (gas hydrate, liquid and gas pore fill, and solid sediment grains) and their complex spatial arrangement hinder the a priori prediction of the thermal conductivity of hydrate-bearing sediments. Previous studies have been unable to capture the full parameter space covered by variations in grain size, specific surface, degree of saturation, nature of pore filling material, and effective stress for hydrate-bearing samples. Here we report on systematic measurements of the thermal conductivity of air dry, water- and tetrohydrofuran (THF)-saturated, and THF hydrate-saturated sand and clay samples at vertical effective stress of 0.05 to 1 MPa (corresponding to depths as great as 100 m below seafloor). Results reveal that the bulk thermal conductivity of the samples in every case reflects a complex interplay among particle size, effective stress, porosity, and fluid-versus-hydrate filled pore spaces. The thermal conductivity of THF hydrate-bearing soils increases upon hydrate formation although the thermal conductivities of THF solution and THF hydrate are almost the same. Several mechanisms can contribute to this effect including cryogenic suction during hydrate crystal growth and the ensuing porosity reduction in the surrounding sediment, increased mean effective stress due to hydrate formation under zero lateral strain conditions, and decreased interface thermal impedance as grain-liquid interfaces are transformed into grain-hydrate interfaces. Copyright 2009 by the American Geophysical Union.

  3. Radiative thermal conduction fronts

    Science.gov (United States)

    Borkowski, Kazimierz J.; Balbus, Steven A.; Fristrom, Carl C.

    1990-01-01

    The discovery of the O VI interstellar absorption lines in our Galaxy by the Copernicus observatory was a turning point in our understanding of the Interstellar Medium (ISM). It implied the presence of widespread hot (approx. 10 to the 6th power K) gas in disk galaxies. The detection of highly ionized species in quasi-stellar objects' absorption spectra may be the first indirect observation of this hot phase in external disk galaxies. Previous efforts to understand extensive O VI absorption line data from our Galaxy were not very successful in locating the regions where this absorption originates. The location at interfaces between evaporating ISM clouds and hot gas was favored, but recent studies of steady-state conduction fronts in spherical clouds by Ballet, Arnaud, and Rothenflug (1986) and Bohringer and Hartquist (1987) rejected evaporative fronts as the absorption sites. Researchers report here on time-dependent nonequilibrium calculations of planar conductive fronts whose properties match well with observations, and suggest reasons for the difference between the researchers' results and the above. They included magnetic fields in additional models, not reported here, and the conclusions are not affected by their presence.

  4. Dependence of thermal conductivity in micro to nano silica

    Indian Academy of Sciences (India)

    Vangala Dhanunjana Chari; Deepala V S G K Sharma; Pinnelli S R Prasad; S Ramana Murthy

    2013-08-01

    This work presents the measurement of thermal conductivity of nano-silica particles using needle probe method. The validation test of thermal probe was conducted on ice and THF hydrates using our experimental set up and the results are satisfactory when compared with the literature data. The nano silica used in this study is with particle sizes in the range 50–1000 nm. The sand powders sieved in different sizes <75 and 75 m > > 250 m were also studied to probe the particle size dependence on thermal conductivity. Thermal conductivity decreased by about 70% in silica nano powders.

  5. Thermally conducting electron transfer polymers

    Science.gov (United States)

    Byrd, N. R.; Jenkins, R. K.; Lister, J. L.

    1969-01-01

    New polymeric material exhibits excellent physical shock protection, high electrical resistance, and thermal conductivity. It is especially useful for electronic circuitry, such as subminiaturization of components and modular construction of circuits.

  6. Optimising the composition of natural moulding sands including thermal aspects

    Directory of Open Access Journals (Sweden)

    Jerzy St. Kowalski

    2011-04-01

    Full Text Available The paper discusses the problem of the choice of the moulding sand mixture composition in terms of the sand behaviour in contact withmolten metal. Studies of high-temperature phenomena make assessment of the sand composition applicability under real operatingconditions possible, thus leading to the elimination of sand-originating casting defects. The research was conducted on selected moulding materials included in the composition of traditional moulding sand mixtures without the addition of carbon. The effect of moulding sand composition and moisture content on the linear dilatation and stress-induced allotropic changes of quartz was examined. The analysis of these phenomena was based on 3D charts and maps generated from data collected during the tests.

  7. Thermal conductivity of graphene laminate.

    Science.gov (United States)

    Malekpour, H; Chang, K-H; Chen, J-C; Lu, C-Y; Nika, D L; Novoselov, K S; Balandin, A A

    2014-09-10

    We have investigated thermal conductivity of graphene laminate films deposited on polyethylene terephthalate substrates. Two types of graphene laminate were studied, as deposited and compressed, in order to determine the physical parameters affecting the heat conduction the most. The measurements were performed using the optothermal Raman technique and a set of suspended samples with the graphene laminate thickness from 9 to 44 μm. The thermal conductivity of graphene laminate was found to be in the range from 40 to 90 W/mK at room temperature. It was found unexpectedly that the average size and the alignment of graphene flakes are more important parameters defining the heat conduction than the mass density of the graphene laminate. The thermal conductivity scales up linearly with the average graphene flake size in both uncompressed and compressed laminates. The compressed laminates have higher thermal conductivity for the same average flake size owing to better flake alignment. Coating plastic materials with thin graphene laminate films that have up to 600× higher thermal conductivity than plastics may have important practical implications.

  8. Thermal Conductivity of Foam Glass

    DEFF Research Database (Denmark)

    Petersen, Rasmus Rosenlund; König, Jakob; Yue, Yuanzheng

    Due to the increased focus on energy savings and waste recycling foam glass materials have gained increased attention. The production process of foam glass is a potential low-cost recycle option for challenging waste, e.g. CRT glass and industrial waste (fly ash and slags). Foam glass is used...... as thermal insulating material in building and chemical industry. The large volume of gas (porosity 90 – 95%) is the main reason of the low thermal conductivity of the foam glass. If gases with lower thermal conductivity compared to air are entrapped in the glass melt, the derived foam glass will contain...... only closed pores and its overall thermal conductivity will be much lower than that of the foam glass with open pores. In this work we have prepared foam glass using different types of recycled glasses and different kinds of foaming agents. This enabled the formation of foam glasses having gas cells...

  9. Minimum Thermal Conductivity of Superlattices

    Energy Technology Data Exchange (ETDEWEB)

    Simkin, M. V.; Mahan, G. D.

    2000-01-31

    The phonon thermal conductivity of a multilayer is calculated for transport perpendicular to the layers. There is a crossover between particle transport for thick layers to wave transport for thin layers. The calculations show that the conductivity has a minimum value for a layer thickness somewhat smaller then the mean free path of the phonons. (c) 2000 The American Physical Society.

  10. Thermal Conductivity of Diamond Composites

    Directory of Open Access Journals (Sweden)

    Fedor M. Shakhov

    2009-12-01

    Full Text Available A major problem challenging specialists in present-day materials sciences is the development of compact, cheap to fabricate heat sinks for electronic devices, primarily for computer processors, semiconductor lasers, high-power microchips, and electronics components. The materials currently used for heat sinks of such devices are aluminum and copper, with thermal conductivities of about 250 W/(m·K and 400 W/(m·K, respectively. Significantly, the thermal expansion coefficient of metals differs markedly from those of the materials employed in semiconductor electronics (mostly silicon; one should add here the low electrical resistivity metals possess. By contrast, natural single-crystal diamond is known to feature the highest thermal conductivity of all the bulk materials studied thus far, as high as 2,200 W/(m·K. Needless to say, it cannot be applied in heat removal technology because of high cost. Recently, SiC- and AlN-based ceramics have started enjoying wide use as heat sink materials; the thermal conductivity of such composites, however, is inferior to that of metals by nearly a factor two. This prompts a challenging scientific problem to develop diamond-based composites with thermal characteristics superior to those of aluminum and copper, adjustable thermal expansion coefficient, low electrical conductivity and a moderate cost, below that of the natural single-crystal diamond. The present review addresses this problem and appraises the results reached by now in studying the possibility of developing composites in diamond-containing systems with a view of obtaining materials with a high thermal conductivity.

  11. Thermal conductance through molecular wires

    CERN Document Server

    Segal, D; Nitzan, A; Segal, Dvira; Nitzan, Abraham; Hanggi, Peter

    2003-01-01

    We consider phononic heat transport through molecular chains connecting two thermal reservoirs. For relatively short molecules at normal temperatures heat conduction is dominated by the harmonic part of the molecular force-field. We develop a general theory for the heat conduction through harmonic chains in 3-dimensions. A Landauer-type expression for the heat conduction is obtained, in agreement with other recent studies. We use this formalism to study the heat conduction properties of alkanes. For relatively short (1-30 carbon atoms) chains the length and temperature dependence of the molecular heat conduction result from the balance of three factors: (i) The molecular frequency spectrum in relation to the frequency cutoff of the thermal reservoirs, (ii) the degree of localization of the molecular normal modes and (iii) the molecule-heat reservoirs coupling. The fact that molecular modes at different frequency regimes have different localization properties gives rise to intricate dependence of the heat cond...

  12. Selected soil thermal conductivity models

    Directory of Open Access Journals (Sweden)

    Rerak Monika

    2017-01-01

    Full Text Available The paper presents collected from the literature models of soil thermal conductivity. This is a very important parameter, which allows one to assess how much heat can be transferred from the underground power cables through the soil. The models are presented in table form, thus when the properties of the soil are given, it is possible to select the most accurate method of calculating its thermal conductivity. Precise determination of this parameter results in designing the cable line in such a way that it does not occur the process of cable overheating.

  13. Thermal diffusivity of peat, sand and their mixtures at different water contents

    Science.gov (United States)

    Gvozdkova, Anna; Arkhangelskaya, Tatiana

    2014-05-01

    physical interpretation: the parameters are (1) the thermal diffusivity of the dry sample; (2) the difference between the highest thermal diffusivity at some optional water content and that of the dry sample; (3) the optional water content at which the thermal diffusivity reaches its maximum; (4) half-width of the peak of the k(θ) curve. The increase of sand contents in studied mixtures was accompanied by the increase of the parameters (1), (2) and (4) and the decrease of the parameter (3). References Parikh R.J., Havens J.A., Scott H.D., 1979. Thermal diffusivity and conductivity of moist porous media. Soil Science Society of America Journal 43, 1050-1052. Arkhangel'skaya T.A., 2009. Parameterization and mathematical modeling of the dependence of soil thermal diffusivity on the water content. Eurasian Soil Science 42 (2), 162-172. doi: 10.1134/S1064229309020070 Arkhangelskaya T.A., 2014. Diversity of thermal conditions within the paleocryogenic soil complexes of the East European Plain: The discussion of key factors and mathematical modeling // Geoderma. Vol. 213. P. 608-616. doi 10.1016/j.geoderma.2013.04.001

  14. Thermal conductivity of thermal barrier coatings

    Energy Technology Data Exchange (ETDEWEB)

    Klemens, P.G.; Gell, M. [Connecticut Univ., Storrs, CT (United States). Inst. of Materials Science

    1998-05-01

    In thermal barrier coatings and other ceramic oxides, heat is conducted by lattice waves, and also by a radiative component which becomes significant at high temperatures. The theory of heat conduction by lattice waves is reviewed in the equipartition limit (above room temperature). The conductivity is composed of contributions from a spectrum of waves, determined by the frequency dependent attenuation length. Interaction between lattice waves (intrinsic processes), scattering by atomic scale point defects and scattering by extended imperfections such as grain boundaries, each limit the attenuation length in different parts of the spectrum. Intrinsic processes yield a spectral conductivity which is independent of frequency. Point defects reduce the contribution of the high frequency spectrum, grain boundaries and other extended defects that of the low frequencies. These reductions are usually independent of each other. Estimates will be given for zirconia containing 7wt% Y{sub 2}O{sub 3}, and for yttrium aluminum garnet. They will be compared to measurements. The effects of grain size, cracks and porosity will be discussed both for the lattice and the radiative components. While the lattice component of the thermal conductivity is reduced substantially by decreasing the grain size to nanometers, the radiative component requires pores or other inclusions of micrometer scale. (orig.) 9 refs.

  15. Thermal radiation of conducting nanoparticles

    CERN Document Server

    Martynenko, Y V; Martynenko, Yu. V.

    2005-01-01

    A simple and universal criterion was obtained for the thermal radiation energy loss efficiency by small conductive particles which include along with metals and graphite also most practically important metal carbides like tungsten carbide, titanium carbide and the number of others.

  16. Determination of thermal conductivity in foundry mould mixtures

    Directory of Open Access Journals (Sweden)

    G. Solenički

    2010-01-01

    Full Text Available For a thorough understanding of the behaviour of foundry mould mixtures, a good knowledge of thermal properties of mould materials is needed. Laboratory determination of thermal conductivity of mould mixtures enables a better control over scabbing defects which are a major problem in green sand mould mixtures. A special instrument has been designed for that purpose and it is described in this work.

  17. High-Thermal-Conductivity Fabrics

    Science.gov (United States)

    Chibante, L. P. Felipe

    2012-01-01

    Heat management with common textiles such as nylon and spandex is hindered by the poor thermal conductivity from the skin surface to cooling surfaces. This innovation showed marked improvement in thermal conductivity of the individual fibers and tubing, as well as components assembled from them. The problem is centered on improving the heat removal of the liquid-cooled ventilation garments (LCVGs) used by astronauts. The current design uses an extensive network of water-cooling tubes that introduces bulkiness and discomfort, and increases fatigue. Range of motion and ease of movement are affected as well. The current technology is the same as developed during the Apollo program of the 1960s. Tubing material is hand-threaded through a spandex/nylon mesh layer, in a series of loops throughout the torso and limbs such that there is close, form-fitting contact with the user. Usually, there is a nylon liner layer to improve comfort. Circulating water is chilled by an external heat exchanger (sublimator). The purpose of this innovation is to produce new LCVG components with improved thermal conductivity. This was addressed using nanocomposite engineering incorporating high-thermalconductivity nanoscale fillers in the fabric and tubing components. Specifically, carbon nanotubes were added using normal processing methods such as thermoplastic melt mixing (compounding twin screw extruder) and downstream processing (fiber spinning, tubing extrusion). Fibers were produced as yarns and woven into fabric cloths. The application of isotropic nanofillers can be modeled using a modified Nielsen Model for conductive fillers in a matrix based on Einstein s viscosity model. This is a drop-in technology with no additional equipment needed. The loading is limited by the ability to maintain adequate dispersion. Undispersed materials will plug filtering screens in processing equipment. Generally, the viscosity increases were acceptable, and allowed the filled polymers to still be

  18. Thermal Conductivity of Humid Air

    Science.gov (United States)

    Beirão, S. G. S.; Ribeiro, A. P. C.; Lourenço, M. J. V.; Santos, F. J. V.; Nieto de Castro, C. A.

    2012-09-01

    In this article, measurements of the thermal conductivity of humid air as a function of pressure, temperature, and mole fraction of water, for pressures up to 5 MPa and temperatures up to 430 K, for different water contents (up to 10 % vapor mole fraction) are reported. Measurements were performed using a transient hot-wire apparatus capable of obtaining data with an uncertainty of 0.8 % for gases. However, as moist air becomes corrosive above 373 K and at pressures >5 MPa, the apparatus, namely, the pressure vessel and the cells had to be modified, by coating all stainless-steel parts with a titanium nitride thin film coating, about 4 μm thick, obtained by physical vapor deposition. The expanded uncertainty (coverage factor k = 2) of the present experimental thermal conductivity data is 1.7 %, while the uncertainty in the mole fraction is estimated to be better than 0.0006. Experimental details regarding the preparation of the samples, the precautions taken to avoid condensation in the tubes connected to the measuring cell, and the method developed for obtaining reliable values of the water content for the gas mixtures are discussed. A preliminary analysis of the application of the kinetic theory of transport properties in reacting mixtures to interpret the complex dependence of the thermal conductivity of humid air on water composition is addressed.

  19. Study of thermal reclamation of used hot-box sand

    Directory of Open Access Journals (Sweden)

    M. Łucarz

    2010-04-01

    Full Text Available The aim of the paper was to determine the number of cycles of thermal reclamation to which a silica sand grain bonded by differentbinders can be subjected with no significant deterioration in strength. The research was carried out on three resins used in hot-boxtechnology. The cores created in this way were subjected to strength tests and the resulting scrap was crushed and reclaimed thermally.The new core sand and cores needed for strength tests were made on the basis of the reclaimed material. The process was repeated ninetimes. The pH reaction of quartz matrix was analysed after each cycle of thermal reclamation. It was observed that there is an impact of thebinder on a silica sand grain. It was concluded that it cannot be fully eliminated by merely using thermal reclamation. The application of additional mechanical reclamation after heat processing can lead to removing the impurities which gather in the irregularities of thereclaimed material and have a significant influence on its chemical reaction.

  20. Thermal Conductance of Andreev Interferometers

    Science.gov (United States)

    Jiang, Z.; Chandrasekhar, V.

    2005-04-01

    We calculate the thermal conductance GT of diffusive Andreev interferometers, which are hybrid loops with one superconducting arm and one normal-metal arm. The presence of the superconductor suppresses GT; however, unlike a conventional superconductor, GT/GTN does not vanish as the temperature T→0, but saturates at a finite value that depends on the resistance of the normal-superconducting interfaces, and their distance from the path of the temperature gradient. The reduction of GT is determined primarily by the suppression of the density of states in the proximity-coupled normal metal along the path of the temperature gradient. GT is also a strongly nonlinear function of the thermal current, as found in recent experiments.

  1. Sand effects on thermal barrier coatings for gas turbine engines

    Science.gov (United States)

    Walock, Michael; Barnett, Blake; Ghoshal, Anindya; Murugan, Muthuvel; Swab, Jeffrey; Pepi, Marc; Hopkins, David; Gazonas, George; Kerner, Kevin

    Accumulation and infiltration of molten/ semi-molten sand and subsequent formation of calcia-magnesia-alumina-silicate (CMAS) deposits in gas turbine engines continues to be a significant problem for aviation assets. This complex problem is compounded by the large variations in the composition, size, and topology of natural sands, gas generator turbine temperatures, thermal barrier coating properties, and the incoming particulate's momentum. In order to simplify the materials testing process, significant time and resources have been spent in the development of synthetic sand mixtures. However, there is debate whether these mixtures accurately mimic the damage observed in field-returned engines. With this study, we provide a direct comparison of CMAS deposits from both natural and synthetic sands. Using spray deposition techniques, 7% yttria-stabilized zirconia coatings are deposited onto bond-coated, Ni-superalloy discs. Each sample is coated with a sand slurry, either natural or synthetic, and exposed to a high temperature flame for 1 hour. Test samples are characterized before and after flame exposure. In addition, the test samples will be compared to field-returned equipment. This research was sponsored by the US Army Research Laboratory, and was accomplished under Cooperative Agreement # W911NF-12-2-0019.

  2. Thermal Conductivity Of Rubble Piles

    CERN Document Server

    Luan, Jing

    2015-01-01

    Rubble piles are a common feature of solar system bodies. They are composed of monolithic elements of ice or rock bound by gravity. Voids occupy a significant fraction of the volume of a rubble pile. They can exist up to pressure $P\\approx \\epsy\\mu$, where $\\epsy$ is the monolithic material's yield strain and $\\mu$ its rigidity. At low $P$, contacts between neighboring elements are confined to a small fraction of their surface areas. As a result, the effective thermal conductivity of a rubble pile, $\\kcon\\approx k(P/(\\epsy\\mu))^{1/2}$, can be orders of magnitude smaller than, $k$, the thermal conductivity of its monolithic elements. In a fluid-free environment, only radiation can transfer energy across voids. It contributes an additional component, $\\krad=16\\ell\\sigma T^3/3$, to the total effective conductivity, $\\keff=\\kcon +\\krad$. Here $\\ell$, the inverse of the opacity per unit volume, is of order the size of the elements and voids. An important distinction between $\\kcon$ and $\\krad$ is that the former i...

  3. Thermal analysis of moulding sands with a polyacrylic binding agent

    Directory of Open Access Journals (Sweden)

    B. Grabowska

    2008-03-01

    Full Text Available Heating of materials causes their physical or chemical changes accompanied by thermal clfccts. Thcrmnl cfrccts of plymcrs an: rclarcd totheir structural changes. such as: melting, crystallization, polymorphous transformations, vitrification. dcgradnlion, dcstmct ion as wcll nsintramolecular or intermolecular reactions. Samples of sodium ptyacrylatc (uscd as a binding agcnr, high-silica sand (grain matrix andsamplcs of moulding sands with a potyacrylic binder aftcr hardening were tcsted derivatographically. Samplcs For thcrmal analysis wcrctaken from sham blocks aRer pcrrorming strcnglh tcsts. Invcstigations wcrc done within the tcmpcmturc rangc: 25-1000°C.Mct hds of thcrmal analysis (DTA,T G} were uscd to dacminc thc thcrmal stability of thc tcstcd snmplcs by cstablisbing rhc tcmpcsaturcand thermal effccts of transformations occurring during hcating. In addition, the invcstigations wcrc to dctcsminc changcs raking placcinside moulding sands whcn in contact with molten mctal. On the basis of differences in Ihermograms of moulding sand samptcs withpolyacrylic binding agcnt. hdcncd cithcr by Ca(Olll and C0: or by microwaves, onc cnn infcr that significant strucrural changesoccurrcd aftcr cross-linking. Thosc changes are rclatcd to intra- and intermolecular rcactions and thc way of hardcning influcnccs thccross-linking reaction - which was also confirmed by mcws of thc spectroscopic investigations (IT-IR. Rarnan, NMR.

  4. Thermal conductivity of molten metals

    Energy Technology Data Exchange (ETDEWEB)

    Peralta-Martinez, Maria Vita

    2000-02-01

    A new instrument for the measurement of the thermal conductivity of molten metals has been designed, built and commissioned. The apparatus is based on the transient hot-wire technique and it is intended for operation over a wide range of temperatures, from ambient up to 1200 K, with an accuracy approaching 2%. In its present form the instrument operates up to 750 K. The construction of the apparatus involved four different stages, first, the design and construction of the sensor and second, the construction of an electronic system for the measurement and storage of data. The third stage was the design and instrumentation of the high temperature furnace for the melting and temperature control of the sample, and finally, an algorithm was developed for the extraction of the thermal conductivity from the raw measurement data. The sensor consists of a cylindrical platinum-wire symmetrically sandwiched between two rectangular plane sheets of alumina. The rectangular sensor is immersed in the molten metal of interest and a voltage step is applied to the ends of the platinum wire to induce heat dissipation and a consequent temperature rise which, is in part, determined by the thermal conductivity of the molten metal. The process is described by a set of partial differential equations and appropriate boundary conditions rather than an approximate analytical solution. An electronic bridge configuration was designed and constructed to perform the measurement of the resistance change of the platinum wire in the time range 20 {mu}s to 1 s. The resistance change is converted to temperature change by a suitable calibration. From these temperature measurements as a function of time the thermal conductivity of the molten metals has been deduced using the Finite Element Method for the solution of the working equations. This work has achieved its objective of improving the accuracy of the measurement of the thermal conductivity of molten metals from {+-}20% to {+-}2%. Measurements

  5. Radiative magnetized thermal conduction fronts

    Science.gov (United States)

    Borkowski, Kazimierz J.; Balbus, Steven A.; Fristrom, Carl C.

    1990-01-01

    The evolution of plane-parallel magnetized thermal conduction fronts in the interstellar medium (ISM) was studied. Separating the coronal ISM phase and interstellar clouds, these fronts have been thought to be the site of the intermediate-temperature regions whose presence was inferred from O VI absorption-line studies. The front evolution was followed numerically, starting from the initial discontinuous temperature distribution between the hot and cold medium, and ending in the final cooling stage of the hot medium. It was found that, for the typical ISM pressure of 4000 K/cu cm and the hot medium temperature of 10 to the 6th K, the transition from evaporation to condensation in a nonmagnetized front occurs when the front thickness is 15 pc. This thickness is a factor of 5 smaller than previously estimated. The O VI column densities in both evaporative and condensation stages agree with observations if the initial hot medium temperature Th exceeds 750,000 K. Condensing conduction fronts give better agreement with observed O VI line profiles because of lower gas temperatures.

  6. Effective Thermal Conductivity of Corrugated Insulating Materials

    Science.gov (United States)

    Yamada, Etsuro; Kato, Masayasu; Tomikawa, Takayuki; Takahashi, Kaneko

    The effective thermal conductivity of corrugated insulating materials which are made by polypropylene or polycarbonate have been measured by employing steady state comparison method for several specimen having various thickness and specific weight. The thermal conductivity of them evaluated are also by using the thermal resistance models, and are compared with above measured values and raw materials' conductivity. The main results obtained in this paper are as follows: (1) In regard to the specimen in this paper, the effective thermal conductivity increases with increasing temperature, but the increasing rate of them is small. (2) There are considerable differences between the measured values and the predicted ones that are estimated by using the thermal resistance model in which heat flow by conduction only. This differences increase with increasing specimens' thickness. This difference become extinct by considering the coexistence heat flow of conduction and radiation in the air phase of specimen. (3) The thermal resistance of specimen increases linearly with increasing specimens' thickness.

  7. Anisotropic Thermal Conductivity of Exfoliated Black Phosphorus.

    Science.gov (United States)

    Jang, Hyejin; Wood, Joshua D; Ryder, Christopher R; Hersam, Mark C; Cahill, David G

    2015-12-22

    The anisotropic thermal conductivity of passivated black phosphorus (BP), a reactive two-dimensional material with strong in-plane anisotropy, is ascertained. The room-temperature thermal conductivity for three crystalline axes of exfoliated BP is measured by time-domain thermo-reflectance. The thermal conductivity along the zigzag direction is ≈2.5 times higher than that of the armchair direction.

  8. The thermal conductivity of clustered nanocolloids

    Directory of Open Access Journals (Sweden)

    Saba Lotfizadeh

    2014-06-01

    Full Text Available We quantify the effect of clustering on the thermal conductivity of colloidal dispersions using silane-treated silica, a system engineered to exhibit reversible clustering under well-controlled conditions. We show that the thermal conductivity increases monotonically with cluster size and spans the entire range between the two limits of Maxwell's theory. The results, corroborated by numerical simulation, demonstrate that large increases of the thermal conductivity of colloidal dispersions are possible, yet fully within the predictions of classical theory.

  9. Thermal conductivity analysis of lanthanum doped manganites

    Energy Technology Data Exchange (ETDEWEB)

    Mansuri, Irfan, E-mail: dr.irfan.mansuri@gmail.com [Indore Institute of Science and Technology, Pithampur Road Rau, Indore-453331 India and School of Physics, Devi Ahilya University, Khandwa Road Campus, Indore-452001 (India); Shaikh, M. W. [School of Physics, Devi Ahilya University, Khandwa Road Campus, Indore-452001, India and Acropolis Technical Campus, Village Tillore, Indore-453331 (India); Khan, E.; Varshney, Dinesh [School of Physics, Devi Ahilya University, Khandwa Road Campus, Indore-452001 (India)

    2014-04-24

    The temperature-dependent thermal conductivity of the doped manganites La{sub 0.7}Ca{sub 0.3}MnO{sub 3} is theoretically analyzed within the framework of Kubo formulae. The Hamiltonian consists of phonon, electron and magnon thermal conductivity contribution term. In this process we took defects, carrier, grain boundary, scattering process term and then calculate phonon, electron and magnon thermal conductivity.

  10. Low lattice thermal conductivity of stanene.

    Science.gov (United States)

    Peng, Bo; Zhang, Hao; Shao, Hezhu; Xu, Yuchen; Zhang, Xiangchao; Zhu, Heyuan

    2016-02-03

    A fundamental understanding of phonon transport in stanene is crucial to predict the thermal performance in potential stanene-based devices. By combining first-principle calculation and phonon Boltzmann transport equation, we obtain the lattice thermal conductivity of stanene. A much lower thermal conductivity (11.6 W/mK) is observed in stanene, which indicates higher thermoelectric efficiency over other 2D materials. The contributions of acoustic and optical phonons to the lattice thermal conductivity are evaluated. Detailed analysis of phase space for three-phonon processes shows that phonon scattering channels LA + LA/TA/ZA ↔ TA/ZA are restricted, leading to the dominant contributions of high-group-velocity LA phonons to the thermal conductivity. The size dependence of thermal conductivity is investigated as well for the purpose of the design of thermoelectric nanostructures.

  11. Effective Thermal Conductivity of Adsorbent Packed Beds

    Science.gov (United States)

    Mori, Hideo; Hamamoto, Yoshinori; Yoshida, Suguru

    The effective thermal conductivity of adsorbent packed beds of granular zeolite 13X and granular silica gel A in the presence of stagnant steam or air was measured under different conditions of the adsorbent bed temperature, particle size and filler-gas pressure. The measured effective thermal conductivity showed to become smaller with decreasing particle size or decreasing pressure, but it was nearly independent of the bed temperature. When steam was the filler-gas, the rise in the thermal conductivity of the adsorbent particles due to steam adsorption led to the increase in the effective thermal conductivity of the bed, and this effect was not negligible at high steam pressure for the bed of large particle size. It was found that both the predictions of the effective thermal conductivity by the Hayashi et al.'s model and the Bauer-Schlünder model generally agreed well with the measurements, by considering the particle thermal conductivity rise due to steam adsorption. The thermal conductivity of a consolidated bed of granular zeolite 13X was also measured, and it was found to be much larger than that of the packed bed especially at lower pressure. The above prediction models underestimated the effective thermal conductivity of the consolidated bed.

  12. The Electronic Thermal Conductivity of Graphene.

    Science.gov (United States)

    Kim, Tae Yun; Park, Cheol-Hwan; Marzari, Nicola

    2016-04-13

    Graphene, as a semimetal with the largest known thermal conductivity, is an ideal system to study the interplay between electronic and lattice contributions to thermal transport. While the total electrical and thermal conductivity have been extensively investigated, a detailed first-principles study of its electronic thermal conductivity is still missing. Here, we first characterize the electron-phonon intrinsic contribution to the electronic thermal resistivity of graphene as a function of doping using electronic and phonon dispersions and electron-phonon couplings calculated from first-principles at the level of density-functional theory and many-body perturbation theory (GW). Then, we include extrinsic electron-impurity scattering using low-temperature experimental estimates. Under these conditions, we find that the in-plane electronic thermal conductivity κe of doped graphene is ∼300 W/mK at room temperature, independently of doping. This result is much larger than expected and comparable to the total thermal conductivity of typical metals, contributing ∼10% to the total thermal conductivity of bulk graphene. Notably, in samples whose physical or domain sizes are of the order of few micrometers or smaller, the relative contribution coming from the electronic thermal conductivity is more important than in the bulk limit, because lattice thermal conductivity is much more sensitive to sample or grain size at these scales. Last, when electron-impurity scattering effects are included we find that the electronic thermal conductivity is reduced by 30 to 70%. We also find that the Wiedemann-Franz law is broadly satisfied at low and high temperatures but with the largest deviations of 20-50% around room temperature.

  13. Anisotropic thermal conductivity in uranium dioxide.

    Science.gov (United States)

    Gofryk, K; Du, S; Stanek, C R; Lashley, J C; Liu, X-Y; Schulze, R K; Smith, J L; Safarik, D J; Byler, D D; McClellan, K J; Uberuaga, B P; Scott, B L; Andersson, D A

    2014-08-01

    The thermal conductivity of uranium dioxide has been studied for over half a century, as uranium dioxide is the fuel used in a majority of operating nuclear reactors and thermal conductivity controls the conversion of heat produced by fission events to electricity. Because uranium dioxide is a cubic compound and thermal conductivity is a second-rank tensor, it has always been assumed to be isotropic. We report thermal conductivity measurements on oriented uranium dioxide single crystals that show anisotropy from 4 K to above 300 K. Our results indicate that phonon-spin scattering is important for understanding the general thermal conductivity behaviour, and also explains the anisotropy by coupling to the applied temperature gradient and breaking cubic symmetry.

  14. Thermal conductivity of unsaturated clay-rocks

    Directory of Open Access Journals (Sweden)

    D. Jougnot

    2010-01-01

    Full Text Available The parameters used to describe the electrical conductivity of a porous material can be used to describe also its thermal conductivity. A new relationship is developed to connect the thermal conductivity of an unsaturated porous material to the thermal conductivity of the different phases of the composite, and two electrical parameters called the first and second Archie's exponents. A good agreement is obtained between the new model and thermal conductivity measurements performed using packs of glass beads and core samples of the Callovo-Oxfordian clay-rocks at different saturations of the water phase. We showed that the three model parameters optimised to fit the new model against experimental data (namely the thermal conductivity of the solid phase and the two Archie's exponents are consistent with independent estimates. We also observed that the anisotropy of the effective thermal conductivity of the Callovo-Oxfordian clay-rock was mainly due to the anisotropy of the thermal conductivity of the solid phase.

  15. Thermal conductivity of nanoscale thin nickel films

    Institute of Scientific and Technical Information of China (English)

    YUAN Shiping; JIANG Peixue

    2005-01-01

    The inhomogeneous non-equilibrium molecular dynamics (NEMD) scheme is applied to model phonon heat conduction in thin nickel films. The electronic contribution to the thermal conductivity of the film is deduced from the electrical conductivity through the use of the Wiedemann-Franz law. At the average temperature of T = 300 K, which is lower than the Debye temperature ()D = 450 K,the results show that in a film thickness range of about 1-11 nm, the calculated cross-plane thermal conductivity decreases almost linearly with the decreasing film thickness, exhibiting a remarkable reduction compared with the bulk value. The electrical and thermal conductivities are anisotropic in thin nickel films for the thickness under about 10 nm. The phonon mean free path is estimated and the size effect on the thermal conductivity is attributed to the reduction of the phonon mean free path according to the kinetic theory.

  16. Electrically conductive and thermally conductive materials for electronic packaging

    Science.gov (United States)

    Liu, Zongrong

    The aim of this dissertation is to develop electrically or thermally conductive materials that are needed for electronic packaging and microelectronic cooling. These materials are in the form of coatings and are made from pastes. The research work encompasses paste formulation, studying the process of converting a paste to a conductive material, relating the processing conditions to the structure and performance, and evaluating performance attributes that are relevant to the application of these conductive materials. The research has resulted in new information that is valuable to the microelectronic industry. Work on electrically conductive materials emphasizes the development of electrical interconnection materials in the form of air-firable glass-free silver-based electrically conductive thick films, which use the Ti-Al alloy as the binder and are in contrast to conventional films that use glass as the binder. The air-firability, as enabled by minor additions of tin and zinc to the paste, is in contrast to previous glass-free films that are not firable. The recommended firing condition is 930°C in air. The organic vehicle in the paste comprises ethyl cellulose, which undergoes thermal decomposition during burnout of the paste. The ethyl cellulose is dissolved in ether, which facilitates the burnout. Excessive ethyl cellulose hinders the burnout. A higher heating rate results in more residue after burnout. The presence of silver particles facilitates drying and burnout. Firing in air gives lower resistivity than firing in oxygen. Firing in argon gives poor films. Compared to conventional films that use glass as the binder, these films, when appropriately fired, exhibit lower electrical resistivity (2.5 x 10-6 O.cm) and higher scratch resistance. Work on thermally conductive materials addresses thermal interface materials, which are materials placed at the interface between a heat sink and a heat source for the purpose of improving the thermal contact. Heat

  17. Thermal Conductivity and Sintering Behavior of Advanced Thermal Barrier Coatings

    Science.gov (United States)

    Zhu, Dongming; Miller, Robert A.

    2002-01-01

    Advanced thermal barrier coatings, having significantly reduced long-term thermal conductivities, are being developed using an approach that emphasizes real-time monitoring of thermal conductivity under conditions that are engine-like in terms of temperatures and heat fluxes. This is in contrast to the traditional approach where coatings are initially optimized in terms of furnace and burner rig durability with subsequent measurement in the as-processed or furnace-sintered condition. The present work establishes a laser high-heat-flux test as the basis for evaluating advanced plasma-sprayed and physical vapor-deposited thermal barrier coatings under the NASA Ultra Efficient Engine Technology (UEET) Program. The candidate coating materials for this program are novel thermal barrier coatings that are found to have significantly reduced thermal conductivities due to an oxide-defect-cluster design. Critical issues for designing advanced low conductivity coatings with improved coating durability are also discussed.

  18. Thermal Conductance through Sapphire-Sapphire Bonding

    Science.gov (United States)

    Suzuki, T.; Tomaru, T.; Haruyama, T.; Shintomi, T.; Uchinyama, T.; Miyoki, S.; Ohashi, M.; Kuroda, K.

    2003-07-01

    Thermal conductance on sapphire-sapphire bonded interface has been investigated. Two pieces of single crystal sapphire bar with square cross section were bonded together by adhesion free bonding. In two sections of the bar, thermal conductivity was measured between 5 K to 300K. One section contains a bonded interface and the other section measured a thermal conductivity of the sapphire as a reference. No significant thermal resistance due to bonded interface was found from this measurement. Obtained thermal conductivity reaches κ 1 × 104 [W/m·K] in temperature range of T = 20 ˜ 30 K which is a planned operating temperature of a cryogenic mirror of the Large scale Cryogenic Gravitational wave telescope. It looks promising for sapphire bonding technique to improve a heat transfer from a large cryogenic mirror to susp ension wires.

  19. Thermal conductivity of sintered lithium orthosilicate compacts

    Science.gov (United States)

    Löbbecke, Birgit; Knitter, Regina; Rohde, Magnus; Reimann, Jörg

    2009-04-01

    The design of solid breeder blankets is strongly affected by the low values of thermal conductivity and density of ceramic breeder pebble beds. A significant rise of both quantities would enhance the thermal performance and lead to an increased tritium breeding ratio. In order to improve these quantities pretreated lithium orthosilicate pebble material was dry pressed and subsequently sintered. The thermal conductivity of cylindrical pellets was determined by the heat pulse method using a laser flash device. A pebble bed characteristic sample was also investigated in order to check the measurement accuracy in comparison with previous results. Furthermore, two samples of low density cellular ceramics were also prepared by infiltration of polymer foams with a ceramic slurry. The thermal conductivity results show that the values are affected both by the particle size and the sample density. Thermal conductivity values of higher than 2 W/m K were obtained using large particles and sintering at 1000 °C.

  20. A new low-cost method of reclaiming mixed foundry waste sand based on wet-thermal composite reclamation

    Institute of Scientific and Technical Information of China (English)

    Fan Zitian; Liu Fuchu; Long Wei; Li Guona

    2014-01-01

    A lot of mixed clay-resin waste sand from large-scale iron foundries is discharged every day; so mixed waste sand reclamation in low cost and high quality has a great realistic significance. In the study to investigate the possibility of reusing two types of waste foundry sands, resin bonded sand and clay bonded sand which came from a Chinese casting factory, a new low-cost reclamation method of the mixed foundry waste sand based on the wet-thermal composite reclamation was proposed. The waste resin bonded sand was first reclaimed by a thermal method and the waste clay bonded sand was reclaimed by a wet method. Then, hot thermal reclaimed sand and the dehydrated wet reclaimed sand were mixed in certain proportions so that the hot thermal reclaimed sand dried the wet reclaimed sand leaving some water. The thermal reclamation efficiency of the waste resin bonded sand was researched at different heat levels. The optimized wet reclamation process of the waste clay bonded sand was achieved by investigating the effects of wet reclamation times, sand-water ratio and pH value on the reclaimed sand characteristics. The composite reclamation cost also was calculated. The research results showed that the properties of the mixed reclaimed sand can satisfy the application requirements of foundries; in which the temperature of the thermal reclamation waste resin bonded sand needs to be about 800 ºC, the number of cycles of wet reclamation waste clay bonded sand should reach four to five, the optimal sand-water ratio of wet reclamation is around 1:1.5, and the pH value should be adjusted by adding acid. The mass ratio of hot thermal reclaimed sand to dehydrated wet reclaimed sand is about 1:2.5, and the composite reclaimed sand cost is around 100 yuan RMB per ton.

  1. A new low-cost method of reclaiming mixed foundry waste sand based on wet-thermal composite reclamation

    Directory of Open Access Journals (Sweden)

    Fan Zitian

    2014-09-01

    Full Text Available A lot of mixed clay-resin waste sand from large-scale iron foundries is discharged every day; so mixed waste sand reclamation in low cost and high quality has a great realistic significance. In the study to investigate the possibility of reusing two types of waste foundry sands, resin bonded sand and clay bonded sand which came from a Chinese casting factory, a new low-cost reclamation method of the mixed foundry waste sand based on the wet-thermal composite reclamation was proposed. The waste resin bonded sand was first reclaimed by a thermal method and the waste clay bonded sand was reclaimed by a wet method. Then, hot thermal reclaimed sand and the dehydrated wet reclaimed sand were mixed in certain proportions so that the hot thermal reclaimed sand dried the wet reclaimed sand leaving some water. The thermal reclamation efficiency of the waste resin bonded sand was researched at different heat levels. The optimized wet reclamation process of the waste clay bonded sand was achieved by investigating the effects of wet reclamation times, sand-water ratio and pH value on the reclaimed sand characteristics. The composite reclamation cost also was calculated. The research results showed that the properties of the mixed reclaimed sand can satisfy the application requirements of foundries; in which the temperature of the thermal reclamation waste resin bonded sand needs to be about 800 篊, the number of cycles of wet reclamation waste clay bonded sand should reach four to five, the optimal sand-water ratio of wet reclamation is around 1:1.5, and the pH value should be adjusted by adding acid. The mass ratio of hot thermal reclaimed sand to dehydrated wet reclaimed sand is about 1:2.5, and the composite reclaimed sand cost is around 100 yuan RMB per ton.

  2. THERMAL CONDUCTIVITY OF RUBBERIZED GYPSUM BOARD

    Directory of Open Access Journals (Sweden)

    Taher Abu-Lebdeh

    2014-01-01

    Full Text Available The disposal of scrap tires is a challenging task and hence an innovative solution to meet these challenges is needed. Extensive work has been done on the utilization of waste tires in a variety of applications in asphalt pavements and concrete. However, previous investigations focus only on the mechanical properties of the rubberized materials, but few on the thermal performance. This is especially true for rubberized gypsum. Limited or no experimental data on the thermal performance of rubberized gypsum board are available. In this study, an experimental program is established to investigate the effect of amount and size of crumb rubber on the thermal properties of gypsum materials. Gypsum is replaced by four different percentage of crumb rubber: 10, 20, 30 and 40% by weight of gypsum and two sizes of crumb rubber (#30, #10_20 to make eight rubberized gypsum specimens. The prepared specimens were tested for thermal conductivity using an apparatus specially designed and constructed for this purpose. The experimental program was concluded by proposing an empirical equation to predict the thermal conductivity of rubberized gypsum board. Results indicated better thermal performance of the gypsum board due to the addition of crumb rubber. Thermal conductivity of the rubberized gypsum was 18-38% lower than the ordinary gypsum. It is concluded that thermal conductivity of rubberized gypsum decreases with the increase of crumb rubber regardless the size of the rubber and that thermal conductivity of mixtures contained 40% of rubber was about 38% lower than conventional mixture when crumb rubber #10_20 was added, while the thermal conductivity reduced by 22% when crumb rubber #30 was added. The study suggested for future work to investigate the effect of air voids size and ratio on the thermal conductivity of rubberized gypsum.

  3. Thermal conductivity measurements of Summit polycrystalline silicon.

    Energy Technology Data Exchange (ETDEWEB)

    Clemens, Rebecca; Kuppers, Jaron D.; Phinney, Leslie Mary

    2006-11-01

    A capability for measuring the thermal conductivity of microelectromechanical systems (MEMS) materials using a steady state resistance technique was developed and used to measure the thermal conductivities of SUMMiT{trademark} V layers. Thermal conductivities were measured over two temperature ranges: 100K to 350K and 293K to 575K in order to generate two data sets. The steady state resistance technique uses surface micromachined bridge structures fabricated using the standard SUMMiT fabrication process. Electrical resistance and resistivity data are reported for poly1-poly2 laminate, poly2, poly3, and poly4 polysilicon structural layers in the SUMMiT process from 83K to 575K. Thermal conductivity measurements for these polysilicon layers demonstrate for the first time that the thermal conductivity is a function of the particular SUMMiT layer. Also, the poly2 layer has a different variation in thermal conductivity as the temperature is decreased than the poly1-poly2 laminate, poly3, and poly4 layers. As the temperature increases above room temperature, the difference in thermal conductivity between the layers decreases.

  4. Equivalent thermal conductivity of heat pipes

    Institute of Scientific and Technical Information of China (English)

    Zesheng LU; Binghui MA

    2008-01-01

    In precision machining, the machining error from thermal distortion carries a high proportion of the total errors. If a precision machining tool can transfer heat fast, the thermal distortion will be reduced and the machining precision will be improved. A heat pipe working based on phase transitions of the inner working liquid transfers heat with high efficiency and is widely applied in spaceflight and chemical industries. In mechanics, applications of heat pipes are correspondingly less. When a heat pipe is applied to a hydrostatic motor-ized spindle, the thermal distortion cannot be solved dur-ing the heat transfer process because thermal conductivity or equivalent thermal conductivity should be provided first for special application in mechanics. An equivalent thermal conductivity model based on equivalent thermal resistances is established. Performance tests for a screen wick pipe, gravity pipe, and rotation heat pipe are done to validate the efficiency of the equivalent thermal conduc-tivity model. The proposed model provides a calculation method for the thermal distortion analysis of heat pipes applied in the motorized spindle.

  5. Increased thermal conductivity monolithic zeolite structures

    Science.gov (United States)

    Klett, James; Klett, Lynn; Kaufman, Jonathan

    2008-11-25

    A monolith comprises a zeolite, a thermally conductive carbon, and a binder. The zeolite is included in the form of beads, pellets, powders and mixtures thereof. The thermally conductive carbon can be carbon nano-fibers, diamond or graphite which provide thermal conductivities in excess of about 100 W/mK to more than 1,000 W/mK. A method of preparing a zeolite monolith includes the steps of mixing a zeolite dispersion in an aqueous colloidal silica binder with a dispersion of carbon nano-fibers in water followed by dehydration and curing of the binder is given.

  6. New method for measuring the thermal conductivity.

    Science.gov (United States)

    Goldratt, E; Greenfield, A J

    1978-11-01

    A new experimental method is presented for measuring the thermal conductivity as a function of temperature. The basic innovation lies in extracting from the measured temperature profile of a sample in vacuo, the thermal conductivity of each individual cross-sectional sample element. The estimated experimental error is +/-1%. Not only is high accuracy achieved, but also a self-checking procedure offers the possibility of avoiding systematic errors. Measurements on two samples of type 304 stainless steel are presented. Three independent sets of measurements give consistent values for the thermal conductivity to well within the estimated error of +/-1%.

  7. Conductive thermal modeling of Wyoming geothermal systems

    Energy Technology Data Exchange (ETDEWEB)

    Heasler, H.P.; Ruscetta, C.A.; Foley, D. (eds.)

    1981-05-01

    A summary of techniques used by the Wyoming Geothermal Resource Assessment Group in defining low-temperature hydrothermal resource areas is presented. Emphasis is placed on thermal modeling techniques appropriate to Wyoming's geologic setting. Thermal parameters discussed include oil-well bottom hole temperatures, heat flow, thermal conductivity, and measured temperature-depth profiles. Examples of the use of these techniques are from the regional study of the Bighorn Basin and two site specific studies within the Basin.

  8. Lattice thermal conductivity evaluated using elastic properties

    Science.gov (United States)

    Jia, Tiantian; Chen, Gang; Zhang, Yongsheng

    2017-04-01

    Lattice thermal conductivity is one of the most important thermoelectric parameters in determining the energy conversion efficiency of thermoelectric materials. However, the lattice thermal conductivity evaluation requires time-consuming first-principles (quasi)phonon calculations, which limits seeking high-performance thermoelectric materials through high-throughput computations. Here, we establish a methodology to determine the Debye temperature Θ , Grüneisen parameter γ , and lattice thermal conductivity κ using computationally feasible elastic properties (the bulk and shear moduli). For 39 compounds with three different prototypes (the cubic isotropic rocksalt and zinc blende, and the noncubic anisotropic wurtzite), the theoretically calculated Θ ,γ , and κ are in reasonable agreement with those determined using (quasi)harmonic phonon calculations or experimental measurements. Our results show that the methodology is an efficient tool to predict the anharmonicity and the lattice thermal conductivity.

  9. Engineering thermal conductivity in polymer blends

    Science.gov (United States)

    Rashidi, Vahid; Coyle, Eleanor; Kieffer, John; Pipe, Kevin

    Weak inter-chain bonding in polymers is believed to be a bottleneck for both thermal conductivity and mechanical strength. Most polymers have low thermal conductivity (~0.1 W/mK), hindering their performance in applications for which thermal management is critical (e.g., electronics packaging). In this work, we use computational methods to study how hydrogen bonding between polymer chains as well as water content can be used to engineer thermal transport in bulk polymers. We examine how changes in the number of hydrogen bonds, chain elongation, density, and vibrational density of states correlate with changes in thermal conductivity for polymer blends composed of different relative constituent fractions. We also consider the effects of bond strength, tacticity, and polymer chain mass. For certain blend fractions, we observe large increases in thermal conductivity, and we analyze these increases in terms of modifications to chain chemistry (e.g., inter-chain bonding) and chain morphology (e.g., chain alignment and radius of gyration). We observe that increasing the number of hydrogen bonds in the system results in better packing as well as better chain alignment and elongation that contribute to enhanced thermal conductivity. The Air Force Office of Scientific Research, Grant No. FA9550-14-1-0010.

  10. Thermal Conductivity of Ordered Molecular Water

    Energy Technology Data Exchange (ETDEWEB)

    W Evans; J Fish; P Keblinski

    2006-02-16

    We use molecular dynamics simulation to investigate thermal transport characteristics of water with various degree of orientational and translational order induced by the application of an electric field. We observe that orientational ordering of the water dipole moments has a minor effect on the thermal conductivity. However, electric-field induced crystallization and associated translational order results in approximately a 3-fold increase of thermal conductivity with respect to the base water, i.e., to values comparable with those characterizing ice crystal structures.

  11. Homogenized thermal conduction model for particulate foods

    Energy Technology Data Exchange (ETDEWEB)

    Chinesta, Francisco [Laboratoire de mecanique des systemes et des procedes, Ecole nationale superieure d' arts et metiers, 151 boulevard de l' Hopital, 75013, Paris (France); Torres, Rafael [Departamento de Ingenieria Mecanica, Universidad Politecnica de Valencia, Camino de Vera s/n. 46071, Valencia (Spain); Ramon, Antonio [AIMPLAS, Gustave Eiffel 4, 46980 Paterna, Valencia (Spain); Rodrigo, Mari Carmen; Rodrigo, Miguel [Instituto de Agroquimica y Tecnologia de Alimentos, Consejo Superior de Investigaciones Cientificas, Apartado de correos 73, 46100, Burjasot (Spain)

    2002-12-01

    This paper deals with the definition of an equivalent thermal conductivity for particulate foods. An homogenized thermal model is used to asses the effect of particulate spatial distribution and differences in thermal conductivities. We prove that the spatial average of the conductivity can be used in an homogenized heat transfer model if the conductivity differences among the food components are not very large, usually the highest conductivity ratio between the foods components is lower than 5. In the general case we propose to use a standard spatial homogenization procedure. Although the heterogeneity give rise to an anisotropic heat transfer behaviour, this effect is negligible when the food particles are randomly distributed. When we use pre-mixed particulate foods a statistical average can be defined from a small number of possible particle arrangements. (authors)

  12. Thermal Conductivity of Carbon Nanotube Composite Films

    Science.gov (United States)

    Ngo, Quoc; Cruden, Brett A.; Cassell, Alan M.; Walker, Megan D.; Koehne, Jessica E.; Meyyappan, M.; Li, Jun; Yang, Cary Y.

    2004-01-01

    State-of-the-art ICs for microprocessors routinely dissipate power densities on the order of 50 W/sq cm. This large power is due to the localized heating of ICs operating at high frequencies, and must be managed for future high-frequency microelectronic applications. Our approach involves finding new and efficient thermally conductive materials. Exploiting carbon nanotube (CNT) films and composites for their superior axial thermal conductance properties has the potential for such an application requiring efficient heat transfer. In this work, we present thermal contact resistance measurement results for CNT and CNT-Cu composite films. It is shown that Cu-filled CNT arrays enhance thermal conductance when compared to as-grown CNT arrays. Furthermore, the CNT-Cu composite material provides a mechanically robust alternative to current IC packaging technology.

  13. Thickness dependent thermal conductivity of gallium nitride

    Science.gov (United States)

    Ziade, Elbara; Yang, Jia; Brummer, Gordie; Nothern, Denis; Moustakas, Theodore; Schmidt, Aaron J.

    2017-01-01

    As the size of gallium nitride (GaN) transistors is reduced in order to reach higher operating frequencies, heat dissipation becomes the critical bottleneck in device performance and longevity. Despite the importance of characterizing the physics governing the thermal transport in thin GaN films, the literature is far from conclusive. In this letter, we report measurements of thermal conductivity in a GaN film with thickness ranging from 15-1000 nm grown on 4H-SiC without a transition layer. Additionally, we measure the thermal conductivity in the GaN film when it is 1 μm-thick in the temperature range of 300 < T < 600 K and use a phonon transport model to explain the thermal conductivity in this film.

  14. A universal thermal conductance of charge carriers

    Energy Technology Data Exchange (ETDEWEB)

    Greiner, A.; Reggiani, L. [Lecce, Univ. (Italy). Ist. Nazionale di Fisica della Materia. Dipt. di Scienza dei Materiali; Kuhn, T. [Munster, Westfalische Wilhelms-Univ. (Germany). Inst. fur Theoretische Physik II; Varani, L. [Montpellier, Univ. Montpellier II (France). Centre d`Electronique et de Micro-optoelectronique

    1996-12-01

    A universal thermal conductance of charge carriers K = 2{pi}{sup 2}k{sub B}{sup 2}T / (3h) is rigorously derived within a correlation-function formalism. Similar to the case of the universal electrical conductance G = 2e{sup 2} / h this result pertains to one-dimensional, ballistic, and degenerate conditions for non-interacting particles.

  15. The Lattice and Thermal Radiation Conductivity of Thermal Barrier Coatings

    Science.gov (United States)

    Zhu, Dongming; Spuckler, Charles M.

    2008-01-01

    The lattice and radiation conductivity of thermal barrier coatings was evaluated using a laser heat flux approach. A diffusion model has been established to correlate the apparent thermal conductivity of the coating to the lattice and radiation conductivity. The radiation conductivity component can be expressed as a function of temperature and the scattering and absorption properties of the coating material. High temperature scattering and absorption of the coating systems can also be derived based on the testing results using the modeling approach. The model prediction is found to have good agreement with experimental observations.

  16. Thermal aspects of temperature transformations in silica sand

    Directory of Open Access Journals (Sweden)

    J.St. Kowalski

    2010-07-01

    Full Text Available Problems related with the choice of moulding sand composition considering its behaviour in contact with molten metal were discussed.The investigations of high-temperature phenomena enable moulding sand composition to be evaluated in terms of its applicability underthe specific conditions of a foundry shop. It is also possible to eliminate the casting defects related to moulding sand and its properties. The investigations were carried out on selected moulding sands from the family of the traditional carbon-free moulding mixtures. The effect of moulding sand composition and moisture content on the linear dilatation and stress formation caused by an allotropic quartz transformation was determined. The investigated phenomena were analysed on 3D diagrams plotted from the test data. A strong effect of the beta quartz - alpha quartz transformation at a temperature of about 6000C was stated.

  17. Thermal conductivity of different colored compomers.

    Science.gov (United States)

    Guler, Cigdem; Keles, Ali; Guler, Mehmet S; Karagoz, Sendogan; Cora, Ömer N; Keskin, Gul

    2017-06-15

    Compomers are mostly used in primary dentition. The thermal conductivity properties of traditional or colored compomers have not been investigated in detail so far. The aim of this in vitro study was to assess and compare the thermal conductivities of traditional and colored compomers. Two sets of compomers - namely, Twinky Star (available in berry, lemon, green, silver, blue, pink, gold and orange shades) and Dyract Extra (available in B1, A3 and A2 shades) - were included in this study. All of the traditional and colored compomers were applied to standard molds and polymerized according to the manufacturers' instructions. Three samples were prepared from each compomer. Measurements were conducted using a heat conduction test setup, and the coefficient of heat conductivity was calculated for each material. The heat conductivity coefficients were statistically analyzed using Kruskal-Wallis and Duncan tests. Uncertainty analysis was also performed on the calculated coefficients of heat conductivity. Statistically significant differences were found (p<0.05) between the thermal conductivity properties of the traditional and colored compomers examined. Among all of the tested compomers, the silver shade compomer exhibited the highest coefficient of heat conductivity (p<0.05), while the berry shade exhibited the lowest coefficient (p<0.05). Uncertainty analyses revealed that 6 out of 11 samples showed significant differences. The silver shade compomer should be avoided in deep cavities. The material properties could be improved for colored compomers.

  18. Thermal Conductivity Coefficient from Microscopic Models

    CERN Document Server

    Nemakhavhani, T E

    2016-01-01

    Thermal conductivity of hadron matter is studied using a microscopic transport model, which will be used to simulate ultra-relativistic heavy ion collisions at different energy densities, namely the Ultra-relativistic Quantum Molecular Dynamics (UrQMD). The molecular dynamics simulation is performed for a system of light mesons species (pion, rho, kaon) in a box with periodic boundary conditions. The equilibrium state is investigated by studying chemical equilibrium and thermal equilibrium of the system. Particle multiplicity equilibrates with time, and the energy spectra of different light mesons species have the same slopes and common temperatures when thermal equilibrium is reached. Thermal conductivity transport coefficient is calculated from the heat current - current correlations using the Green-Kubo relations.

  19. Thermal conductivity and interface thermal conductance of thin films in Li ion batteries

    Science.gov (United States)

    Jagannadham, K.

    2016-09-01

    Laser physical vapor deposition is used to deposit thin films of lithium phosphorous oxynitride in nitrogen and lithium nickel manganese oxide in oxygen ambient on Si substrate. LIPON film is also deposited on LiNiMnO film that is deposited on Si. Graphene films consisting of graphene platelets are deposited on Si substrate from a suspension in isopropyl alcohol. Li-graphene films are obtained after Li adsorption by immersion in LiCl solution and further drying. Transient thermo reflectance signal is used to determine the cross-plane thermal conductivity of different layers and interface thermal conductance of the interfaces. The results show that LIPON film with lower thermal conductivity is a thermal barrier. The interface thermal conductance between LIPON and Au or Si is found to be very low. Thermal conductivity of LiNiMnO is found to be reasonably high so that it is not a barrier to thermal transport. Film with graphene platelets shows a higher value and Li adsorbed graphene film shows a much higher value of cross-plane thermal conductivity. The value of interface thermal conductance between graphene and Au or Si (100) substrate is also much lower. The implications of the results for the thermal transport in thin film Li batteries are discussed.

  20. Modulating thermal conduction by the axial strain

    Science.gov (United States)

    Jiang, Jianjun; Zhao, Hong

    2016-09-01

    Recent studies have revealed that the symmetry of interparticle potential plays an important role in the one-dimensional thermal conduction problem. Here we demonstrate that, by introducing strain into the Fermi-Pasta-Ulam-β lattice, the interparticle potential can be converted from symmetric to asymmetric, which leads to a change of the asymptotic decaying behavior of the heat current autocorrelation function. More specifically, such a change in the symmetry of the potential induces a fast decaying stage, in which the heat current autocorrelation function decays faster than power-law manners or in a power-law manner but faster than ~t -1, in the transient stage. The duration of the fast decaying stage increases with increasing strain ratio and decreasing of the temperature. As a result, the thermal conductivity calculated following the Green-Kubo formula may show a truncation-time independent behavior, suggesting a system-size independent thermal conductivity.

  1. Specific heat and thermal conductivity of nanomaterials

    Science.gov (United States)

    Bhatt, Sandhya; Kumar, Raghuvesh; Kumar, Munish

    2017-01-01

    A model is proposed to study the size and shape effects on specific heat and thermal conductivity of nanomaterials. The formulation developed for specific heat is based on the basic concept of cohesive energy and melting temperature. The specific heat of Ag and Au nanoparticles is reported and the effect of size and shape has been studied. We observed that specific heat increases with the reduction of particle size having maximum shape effect for spherical nanoparticle. To provide a more critical test, we extended our model to study the thermal conductivity and used it for the study of Si, diamond, Cu, Ni, Ar, ZrO2, BaTiO3 and SrTiO3 nanomaterials. A significant reduction is found in the thermal conductivity for nanomaterials by decreasing the size. The model predictions are consistent with the available experimental and simulation results. This demonstrates the suitability of the model proposed in this paper.

  2. Thermal Conductivity Measurements of Caged Structural Superconductors

    Science.gov (United States)

    Matsuzaki, H.; Hida, K.; Kase, N.; Nakano, T.; Takeda, N.

    Thermal conductivity of Ca3Rh4Sn13 and Sr3Ir4Sn13 were measured in magnetic fields to reveal superconducting state. From magnetic susceptibility χ(T) and electrical resistivity ρ(T) measurements, superconducting transition temperature Tc of Ca3Rh4Sn13 and Sr3Ir4Sn13 is determined to be 8 and 5 K, respectively. Thermal conductivity κ(T) of Ca3Rh4Sn13 indicates that superconducting state is nodeless s-wave, because residual thermal conductivity κ0/T in zero magnetic field is very small. On the other hand, κ(T) of Sr3Ir4Sn13 in zero magnetic field suggests that superconductivity possesses nodal gap rather than full gap. Whether nodal superconducting gap exists or not still remains to be clarified, because there is a possibility that the achieving temperature is insufficient to discuss superconducting state.

  3. Temperature Dependence of Thermal Conductivity of Nanofluids

    Institute of Scientific and Technical Information of China (English)

    LI Yu-Hua; QU Wei; FENG Jian-Chao

    2008-01-01

    Mechanism of thermal conductivity of nanofluids is analysed and calculated, including Brownian motion effects, particle agglomeration and viscosity, together influenced by temperature. The results show that only Brownian motion as reported is not enough to describe the temperature dependence of the thermal conductivity of nanofluids. The change of particle agglomeration and viscosity with temperature are also important factors. As temperature increases, the reduction of the particle surface energy would decrease the agglomeration of nanopartides, and the reduction of viscosity would improve the Brownian motion. The results agree well with the experimental data reported.

  4. Anisotropic thermal conductivity of magnetic fluids

    Institute of Scientific and Technical Information of China (English)

    Xiaopeng Fang; Yimin Xuan; Qiang Li

    2009-01-01

    Considering the forces acting on the particles and the motion of the particles, this study uses a numerical simulation to investigate the three-dimensional microstructure of the magnetic fluids in the presence of an external magnetic field. A method is proposed for predicting the anisotropic thermal conductivity of magnetic fluids. By introducing an anisotropic structure parameter which characterizes the non-uniform distribution of particles suspended in the magnetic fluids, the traditional Maxwell formula is modified and extended to calculate anisotropic thermal conductivity of the magnetic fluids. The results show that in the presence of an external magnetic field the magnetic nanoparticles form chainlike clusters along the direction of the external magnetic field, which leads to the fact that the thermal conduc-tivity of the magnetic fluid along the chain direction is bigger than that along other directions. The thermal conductivity of the magnetic fluids presents an anisotropic feature. With the increase of the magnetic field strength the chainlike clusters in the magnetic fluid appear to be more obvious, so that the anisotropic feature of heat conduction in the fluids becomes more evident.

  5. An Innovative High Thermal Conductivity Fuel Design

    Energy Technology Data Exchange (ETDEWEB)

    PI: James S. Tulenko; Co-PI: Ronald H. Baney,

    2007-10-14

    Uranium dioxide (UO2) is the most common fuel material in commercial nuclear power reactors. UO2 has the advantages of a high melting point, good high-temperature stability, good chemical compatibility with cladding and coolant, and resistance to radiation. The main disadvantage of UO2 is its low thermal conductivity. During a reactor’s operation, because the thermal conductivity of UO2 is very low, for example, about 2.8 W/m-K at 1000 oC [1], there is a large temperature gradient in the UO2 fuel pellet, causing a very high centerline temperature, and introducing thermal stresses, which lead to extensive fuel pellet cracking. These cracks will add to the release of fission product gases after high burnup. The high fuel operating temperature also increases the rate of fission gas release and the fuel pellet swelling caused by fission gases bubbles. The amount of fission gas release and fuel swelling limits the life time of UO2 fuel in reactor. In addition, the high centerline temperature and large temperature gradient in the fuel pellet, leading to a large amount of stored heat, increase the Zircaloy cladding temperature in a lost of coolant accident (LOCA). The rate of Zircaloy-water reaction becomes significant at the temperature above 1200 oC [2]. The ZrO2 layer generated on the surface of the Zircaloy cladding will affect the heat conduction, and will cause a Zircaloy cladding rupture. The objective of this research is to increase the thermal conductivity of UO2, while not affecting the neutronic property of UO2 significantly. The concept to accomplish this goal is to incorporate another material with high thermal conductivity into the UO2 pellet. Silicon carbide (SiC) is a good candidate, because the thermal conductivity of single crystal SiC is 60 times higher than that of UO2 at room temperature and 30 times higher at 800 oC [3]. Silicon carbide also has the properties of low thermal neutron absorption cross section, high melting point, good chemical

  6. Investigations Regarding the Thermal Conductivity of Straw

    Directory of Open Access Journals (Sweden)

    Marian Pruteanu

    2010-01-01

    Full Text Available The reduction of buildings heat losses and pollutants emissions is a worldwide priority. It’s intending to reduce the specific final energy consumption under limit of 120...150 kWh/m2.yr and even under 15...45 kWh/m2.yr, foreseen in 2020 for the passive houses, which is necessary for a sustainable development and for allowing to became profitable the use of unconventional energies [1]. These values can be achieved through the use of thermal insulations, for protecting the constructions fund and through making envelope elements, as much as possible, from materials with a high thermal resistance, for new buildings. With intention to substitute the conventional thermal insulations: mineral wool, expanded polystyrene, which are both great energy consumers, it’s proposed, among others unconventional technologies and materials, the use of vegetable wastes both as a thermal insulation material and as a material used for building load-bearing and in-fill straw-bale construction. In speciality literature there are presented experimental determinations of this material’s thermal conductivity. The paper proposes a simple method, adequate for the measurement of thermal conductivity for bulk’s materials as straw bales.

  7. Electric conductivity for laboratory and field monitoring of induced partial saturation (IPS) in sands

    Science.gov (United States)

    Kazemiroodsari, Hadi

    Liquefaction is loss of shear strength in fully saturated loose sands caused by build-up of excess pore water pressure, during moderate to large earthquakes, leading to catastrophic failures of structures. Currently used liquefaction mitigation measures are often costly and cannot be applied at sites with existing structures. An innovative, practical, and cost effective liquefaction mitigation technique titled "Induced Partial Saturation" (IPS) was developed by researchers at Northeastern University. The IPS technique is based on injection of sodium percarbonate solution into fully saturated liquefaction susceptible sand. Sodium percarbonate dissolves in water and breaks down into sodium and carbonate ions and hydrogen peroxide which generates oxygen gas bubbles. Oxygen gas bubbles become trapped in sand pores and therefore decrease the degree of saturation of the sand, increase the compressibility of the soil, thus reduce its potential for liquefaction. The implementation of IPS required the development and validation of a monitoring and evaluation technique that would help ensure that the sands are indeed partially saturated. This dissertation focuses on this aspect of the IPS research. The monitoring system developed was based on using electric conductivity fundamentals and probes to detect the transport of chemical solution, calculate degree of saturation of sand, and determine the final zone of partial saturation created by IPS. To understand the fundamentals of electric conductivity, laboratory bench-top tests were conducted using electric conductivity probes and small specimens of Ottawa sand. Bench-top tests were used to study rate of generation of gas bubbles due to reaction of sodium percarbonate solution in sand, and to confirm a theory based on which degree of saturation were calculated. In addition to bench-top tests, electric conductivity probes were used in a relatively large sand specimen prepared in a specially manufactured glass tank. IPS was

  8. Thermal Conductivity of Polyimide/Nanofiller Blends

    Science.gov (United States)

    Ghose, S.; Watson, K. A.; Delozier, D. M.; Working, D. c.; Connell, J. W.; Smith, J. G.; Sun, Y. P.; Lin, Y.

    2006-01-01

    In efforts to improve the thermal conductivity of Ultem(TM) 1000, it was compounded with three carbon based nano-fillers. Multiwalled carbon nanotubes (MWCNT), vapor grown carbon nanofibers (CNF) and expanded graphite (EG) were investigated. Ribbons were extruded to form samples in which the nano-fillers were aligned. Samples were also fabricated by compression molding in which the nano-fillers were randomly oriented. The thermal properties were evaluated by DSC and TGA, and the mechanical properties of the aligned samples were determined by tensile testing. The degree of dispersion and alignment of the nanoparticles were investigated with high-resolution scanning electron microscopy. The thermal conductivity of the samples was measured in both the direction of alignment as well as perpendicular to that direction using the Nanoflash technique. The results of this study will be presented.

  9. Thermal Conductivity of Al-Salt Composites

    Science.gov (United States)

    Li, Peng; Zhang, Mei; Wang, Lijun; Seetharaman, Seshadri

    2015-11-01

    With a view to examine the possibility of estimating the content of entrapped metallic aluminium in the salt cake from aluminium remelting, the thermal diffusivity of reference composites of KCl-NaCl-Al was measured as a function of aluminium metal content at room temperature. The thermal conductivity of the reference composites was found to increase with the metallic Al content. The lumped parameter model approach was carried out to discuss the influence of different geometry arrangements of each phase, viz. air, salts and metallic aluminium on the thermal conductivity. Application of the present results to industrial samples indicates that factors such as the interfacial condition of metallic Al particles have to be considered in order to estimate the amount of entrapped Al in the salt cake.

  10. Local measurement of thermal conductivity and diffusivity

    Energy Technology Data Exchange (ETDEWEB)

    Hurley, David H.; Schley, Robert S. [Materials Science and Engineering Department, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, Idaho 83415-2209 (United States); Khafizov, Marat [Mechanical and Aerospace Engineering Department, The Ohio State University, 201 W. 19th Ave., Columbus, Ohio 43210 (United States); Wendt, Brycen L. [Nuclear Science and Engineering, Idaho State University, 921 S. 8th Ave., Pocatello, Idaho 83209-8060 (United States)

    2015-12-15

    Simultaneous measurement of local thermal diffusivity and conductivity is demonstrated on a range of ceramic samples. This was accomplished by measuring the temperature field spatial profile of samples excited by an amplitude modulated continuous wave laser beam. A thin gold film is applied to the samples to ensure strong optical absorption and to establish a second boundary condition that introduces an expression containing the substrate thermal conductivity. The diffusivity and conductivity are obtained by comparing the measured phase profile of the temperature field to a continuum based model. A sensitivity analysis is used to identify the optimal film thickness for extracting the both substrate conductivity and diffusivity. Proof of principle studies were conducted on a range of samples having thermal properties that are representatives of current and advanced accident tolerant nuclear fuels. It is shown that by including the Kapitza resistance as an additional fitting parameter, the measured conductivity and diffusivity of all the samples considered agreed closely with the literature values. A distinguishing feature of this technique is that it does not require a priori knowledge of the optical spot size which greatly increases measurement reliability and reproducibility.

  11. Local measurement of thermal conductivity and diffusivity

    Science.gov (United States)

    Hurley, David H.; Schley, Robert S.; Khafizov, Marat; Wendt, Brycen L.

    2015-12-01

    Simultaneous measurement of local thermal diffusivity and conductivity is demonstrated on a range of ceramic samples. This was accomplished by measuring the temperature field spatial profile of samples excited by an amplitude modulated continuous wave laser beam. A thin gold film is applied to the samples to ensure strong optical absorption and to establish a second boundary condition that introduces an expression containing the substrate thermal conductivity. The diffusivity and conductivity are obtained by comparing the measured phase profile of the temperature field to a continuum based model. A sensitivity analysis is used to identify the optimal film thickness for extracting the both substrate conductivity and diffusivity. Proof of principle studies were conducted on a range of samples having thermal properties that are representatives of current and advanced accident tolerant nuclear fuels. It is shown that by including the Kapitza resistance as an additional fitting parameter, the measured conductivity and diffusivity of all the samples considered agreed closely with the literature values. A distinguishing feature of this technique is that it does not require a priori knowledge of the optical spot size which greatly increases measurement reliability and reproducibility.

  12. Model calculation of thermal conductivity in antiferromagnets

    Energy Technology Data Exchange (ETDEWEB)

    Mikhail, I.F.I., E-mail: ifi_mikhail@hotmail.com; Ismail, I.M.M.; Ameen, M.

    2015-11-01

    A theoretical study is given of thermal conductivity in antiferromagnetic materials. The study has the advantage that the three-phonon interactions as well as the magnon phonon interactions have been represented by model operators that preserve the important properties of the exact collision operators. A new expression for thermal conductivity has been derived that involves the same terms obtained in our previous work in addition to two new terms. These two terms represent the conservation and quasi-conservation of wavevector that occur in the three-phonon Normal and Umklapp processes respectively. They gave appreciable contributions to the thermal conductivity and have led to an excellent quantitative agreement with the experimental measurements of the antiferromagnet FeCl{sub 2}. - Highlights: • The Boltzmann equations of phonons and magnons in antiferromagnets have been studied. • Model operators have been used to represent the magnon–phonon and three-phonon interactions. • The models possess the same important properties as the exact operators. • A new expression for the thermal conductivity has been derived. • The results showed a good quantitative agreement with the experimental data of FeCl{sub 2}.

  13. Thermal conductivity of a new insulator

    Energy Technology Data Exchange (ETDEWEB)

    Payamara, Jahangir [Physics Department, Shahed University (Iran, Islamic Republic of)], E-mail: jahangirpayamara@yahoo.com

    2011-07-01

    With the depletion of energy resources it becomes increasingly important to save energy. Significant amounts of energy are consumed in residential and commercial buildings, mainly for space heating. The aim of this paper is to assess the thermal conductivity of gunny, a new insulator produced in the Middle East and Far East from plant fiber. An insulation chamber of 0.75x0.6x1m3 was built in the physics department of Shahed University and measurements of the thermal conductivity of gunny were carried out. The thermal conductivity of gunny was found to be 0.80 joules per second meter degree celsius which is good in comparison to wood's thermal conductivity. In addition, results showed that the rate of heat energy hitting the cooler end is lower than that reaching the hot end and that gunny leads to energy savings in buildings. This study demonstrated that gunny can be considered a desirable insulator for buildings.

  14. Thermal conductivity of granular porous media: A pore scale modeling approach

    Directory of Open Access Journals (Sweden)

    R. Askari

    2015-09-01

    Full Text Available Pore scale modeling method has been widely used in the petrophysical studies to estimate macroscopic properties (e.g. porosity, permeability, and electrical resistivity of porous media with respect to their micro structures. Although there is a sumptuous literature about the application of the method to study flow in porous media, there are fewer studies regarding its application to thermal conduction characterization, and the estimation of effective thermal conductivity, which is a salient parameter in many engineering surveys (e.g. geothermal resources and heavy oil recovery. By considering thermal contact resistance, we demonstrate the robustness of the method for predicting the effective thermal conductivity. According to our results obtained from Utah oil sand samples simulations, the simulation of thermal contact resistance is pivotal to grant reliable estimates of effective thermal conductivity. Our estimated effective thermal conductivities exhibit a better compatibility with the experimental data in companion with some famous experimental and analytical equations for the calculation of the effective thermal conductivity. In addition, we reconstruct a porous medium for an Alberta oil sand sample. By increasing roughness, we observe the effect of thermal contact resistance in the decrease of the effective thermal conductivity. However, the roughness effect becomes more noticeable when there is a higher thermal conductivity of solid to fluid ratio. Moreover, by considering the thermal resistance in porous media with different grains sizes, we find that the effective thermal conductivity augments with increased grain size. Our observation is in a reasonable accordance with experimental results. This demonstrates the usefulness of our modeling approach for further computational studies of heat transfer in porous media.

  15. Effects Of Evaporation Rate of Some Common Organic Contaminants on Hydraulic Conductivity of Aquifer Sand

    Science.gov (United States)

    Saud, Q. J.; Hasan, S. E.

    2014-12-01

    As part of a larger study to investigate potential effects of hydrocarbons on the geotechnical properties of aquifer solids, a series of laboratory experiments were carried out to ascertain the influence of evaporation rate of some common and widespread organic contaminants on the hydraulic conductivity of aquifer sand. Gasoline and its constituent chemicals-benzene, toluene, ethylbenzene, xylene (BTEX), isooctane- and trichloroethylene (TCE) were used to contaminate sand samples collected from the aquifer and vadose zone, at varying concentrations for extended periods of time. The goal was to study any change in the chemical makeup of the contaminants and its control on hydraulic conductivity of the sand. It was found that: (a) gasoline breaks down into constituent compounds when subjected to evaporation, e.g. during oil spills and leaks; and (b) lighter compounds volatilize faster and in the following order: TCE> benzene > isooctane > toluene > gasoline> ethylbenzene > xylene. In addition, these contaminants also caused a decrease in hydraulic conductivity of sand by up to 60% as compared to the uncontaminated sand. The inherent differences in the chemical structure of contaminating chemicals influenced hydraulic conductivity such that the observed decrease was greater for aliphatic than aromatic and chlorinated hydrocarbons. The presentation includes details of the experimental set up; evaporation rate, and geotechnical tests; X-ray diffraction and scanning electron microscope studies; and data analyses and interpretation. Rate of evaporation test indicates that residual LNAPLs will occupy a certain portion of the pores in the soil either as liquid or vapor phase in the vadose zone, and will create a coating on the adjacent solid mineral grains in the aquifer. Replacement of air by the LNAPLs along with grain coatings and the intramolecular forces would impede groundwater movement, thus affecting overall permeability of contaminated aquifers. Keywords: aquifer

  16. Impulse propagation in a conducting medium with arbitrary thermal conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Myasnikov, S.P.

    1977-07-01

    An examination is made of impulse propagation in a conducting medium that accounts for its thermal conductivity. Such a medium, even with an infinitely large electric conductivity, will have a weak dispersion. Following dispersion through a sufficiently large time interval, out of the entire set of planar waves comprising a wave packet, only the low-frequency components were shown to remain (these are the components that are propagated at a velocity of c/sub s/) along with the high-frequency components that are propagated at the speed of c/sub T/. Consequently, the initial derangement is converted into two separate waves of a bell-shaped form that run to various sides at a phase velocity equal to the adiabatic speed of sound c/sub s/. 6 references.

  17. Advanced Testing Method for Ground Thermal Conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xiaobing [ORNL; Clemenzi, Rick [Geothermal Design Center Inc.; Liu, Su [University of Tennessee (UT)

    2017-04-01

    A new method is developed that can quickly and more accurately determine the effective ground thermal conductivity (GTC) based on thermal response test (TRT) results. Ground thermal conductivity is an important parameter for sizing ground heat exchangers (GHEXs) used by geothermal heat pump systems. The conventional GTC test method usually requires a TRT for 48 hours with a very stable electric power supply throughout the entire test. In contrast, the new method reduces the required test time by 40%–60% or more, and it can determine GTC even with an unstable or intermittent power supply. Consequently, it can significantly reduce the cost of GTC testing and increase its use, which will enable optimal design of geothermal heat pump systems. Further, this new method provides more information about the thermal properties of the GHEX and the ground than previous techniques. It can verify the installation quality of GHEXs and has the potential, if developed, to characterize the heterogeneous thermal properties of the ground formation surrounding the GHEXs.

  18. Thermal Conductivity Measurements on consolidated Soil Analogs

    Science.gov (United States)

    Seiferlin, K.; Heimberg, M.; Thomas, N.

    2007-08-01

    Heat transport in porous media such as soils and regolith is significantly reduced compared to the properties of compact samples of the same material. The bottle neck for solid state heat transport is the contact area between adjacent grains. For "dry" and unconsolidated materials the contact areas and thus the thermal conductivity are extremely small. Sintering and cementation are two processes that can increase the cross section of interstitial bonds signifcantly. On Mars, cementation can be caused by condensation of water or carbon dioxide ice from the vapor phase, or from salts and minerals that fall out from aqueous solutions. We produced several artificially cemented samples, using small glass beads of uniform size as soil analog. The cementation is achieved by initially molten wax that is mixed with the glass beads while liqiud. The wax freezes preferably at the contact points between grains, thus minimizing surface energy, and consolidates the samples. The thermal conductivity of these samples is then measured in vacuum. We present the results of these measurements and compare them with theoretical models. The observed range of thermal conductivity values can explain some, but not all of the variations in thermal intertia that can be seen in TES remote sensing data.

  19. Sand box experiments with bioclogging of porous media: Hydraulic conductivity reductions

    DEFF Research Database (Denmark)

    Seifert, Dorte; Engesgaard, Peter

    2012-01-01

    Tracer experiments during clogging and de-clogging experiments in a 2D sand box were via an image analysis used to establish a data set on the relation between changes in hydraulic conductivity (K) and relative porosity (β). Clogging appears to create a finger-like tracer transport, which could...... and closer to the substrate source during the experiments suggesting that the zone of clogging moved upstream. Three clogging models, K(β), from the literature were tested for their ability to describe the temporal changes in clogging at the scale of the sand box; the model of Clement et al. (1996......) that makes no assumption on biomass distribution, the plug formation model of Thullner et al. (2002a), and the biofilm-plug formation model of Vandevivere (1995). The plug formation and biofilm-plug formation models both match the observed changes between the hydraulic conductivity of the sand box...

  20. Thermal Conductivity Measurement of Synthesized Mantle Minerals

    Science.gov (United States)

    Asimow, P. D.; Luo, S.; Mosenfelder, J. L.; Liu, W.; Staneff, G. D.; Ahrens, T. J.; Chen, G.

    2002-12-01

    Direct thermal conductivity (k) measurement of mantle minerals is crucial to constrain the thermal profile of the Earth as well as geodynamic studies of the mantle (e.g., to determine the Rayleigh number). We have embarked on systematic multi-anvil syntheses of dense polycrystalline specimens of mantle phases of adequate size and zero porosity for precise thermal conductivity measurements by the 3ω method (\\textit{Cahill and Pohl, Phys. Rev. B, 1987}) under elevated temperatures (T). Coesite and stishovite (see \\textit{Luo et al., GRL, 2002}) as well as majorite and wadsleyite have been synthesized; ringwoodite and perovskite are scheduled. Preliminary thermal conductivity measurements at ambient pressure on coesite (120 - 300 K, 9.53 Wm-1K-1 at 300 K) are consistent with prior room temperature data (\\textit{Yukutake & Shimada, PEPI, 1978}), while our stishovite data at 300 K appear to be low (1.96 Wm-1K-1). Efforts are being made to extend the measurement to higher temperatures (e.g., above Debye temperature Θ D), thus allowing determination of k(T) relationship (say, k~ T-n); success will depend on the decomposition kinetics of these metastable phases. The pressure dependence of k of these synthesized samples can also be measured (\\textit{e.g., Osako et al., HPMPS-6, 2002; Xu et al., EOS, 2001}). Recent thermal conductivity measurement on LiF and Al2O_3 from shock wave loading (\\textit{Holland & Ahrens, 1998}) is consistent with the modeling on MgO and Al2O_3 (\\textit{Manga & Jeanloz, JGR, 1997}) with classical theories. Thus, k values at modest pressures and T (say, above Θ D) would allow extrapolation of k to appropriate mantle conditions.

  1. Thermal conduction in cosmological SPH simulations

    CERN Document Server

    Jubelgas, M; Dolag, K

    2004-01-01

    Thermal conduction in the intracluster medium has been proposed as a possible heating mechanism for offsetting central cooling losses in rich clusters of galaxies. In this study, we introduce a new formalism to model conduction in a diffuse ionised plasma using smoothed particle hydrodynamics (SPH), and we implement it in the parallel TreePM/SPH-code GADGET-2. We consider only isotropic conduction and assume that magnetic suppression can be described in terms of an effective conductivity, taken as a fixed fraction of the temperature-dependent Spitzer rate. We also account for saturation effects in low-density gas. Our formulation manifestly conserves thermal energy even for individual and adaptive timesteps, and is stable in the presence of small-scale temperature noise. This allows us to evolve the thermal diffusion equation with an explicit time integration scheme along with the ordinary hydrodynamics. We use a series of simple test problems to demonstrate the robustness and accuracy of our method. We then ...

  2. Multiscale Modeling of UHTC: Thermal Conductivity

    Science.gov (United States)

    Lawson, John W.; Murry, Daw; Squire, Thomas; Bauschlicher, Charles W.

    2012-01-01

    We are developing a multiscale framework in computational modeling for the ultra high temperature ceramics (UHTC) ZrB2 and HfB2. These materials are characterized by high melting point, good strength, and reasonable oxidation resistance. They are candidate materials for a number of applications in extreme environments including sharp leading edges of hypersonic aircraft. In particular, we used a combination of ab initio methods, atomistic simulations and continuum computations to obtain insights into fundamental properties of these materials. Ab initio methods were used to compute basic structural, mechanical and thermal properties. From these results, a database was constructed to fit a Tersoff style interatomic potential suitable for atomistic simulations. These potentials were used to evaluate the lattice thermal conductivity of single crystals and the thermal resistance of simple grain boundaries. Finite element method (FEM) computations using atomistic results as inputs were performed with meshes constructed on SEM images thereby modeling the realistic microstructure. These continuum computations showed the reduction in thermal conductivity due to the grain boundary network.

  3. Thermal conductivity at different humidity conditions

    DEFF Research Database (Denmark)

    Kristiansen, Finn Harken; Rode, Carsten

    1999-01-01

    The thermal conductivity (the l-value) of several alternative insulation products and a traditional product is determined under different humidity conditions in a specially constructed hot plate apparatus.The hot plate apparatus is constructed with an air gap on each side of the test specimen where...... humidified air can pass. Thus, it is possible to build up different degrees of moisture on each side of the test specimen.The thermal conductivity is determined for the following types of alternative insulation: sheep's wool, flax, paper insulation, perlite and mineral wool. The insulation products were...... by an accumulation of moisture as condensation in the parts of the insulation that lie immediately close to the cold side of the apparatus. The high l-values found are therefore of no practical importance in structures where no condensation occurs. Disregarding these condensation situations, the maximum increase...

  4. Thermal conductivity at different humidity conditions

    DEFF Research Database (Denmark)

    Kristiansen, Finn Harken; Rode, Carsten

    1999-01-01

    humidified air can pass. Thus, it is possible to build up different degrees of moisture on each side of the test specimen.The thermal conductivity is determined for the following types of alternative insulation: sheep's wool, flax, paper insulation, perlite and mineral wool. The insulation products were......The thermal conductivity (the l-value) of several alternative insulation products and a traditional product is determined under different humidity conditions in a specially constructed hot plate apparatus.The hot plate apparatus is constructed with an air gap on each side of the test specimen where...... Ekofiber Vind, Herawool (without support fibres), Heraflax, Isodan with and without salts, Miljø Isolering with and without salts, Perlite (water-repellent), and Rockwool A-batts for comparison.All measurements of the materials started with no affection of moisture. Nevertheless, results were achieved...

  5. Thermal Boundary Conductance: A Materials Science Perspective

    Science.gov (United States)

    Monachon, Christian; Weber, Ludger; Dames, Chris

    2016-07-01

    The thermal boundary conductance (TBC) of materials pairs in atomically intimate contact is reviewed as a practical guide for materials scientists. First, analytical and computational models of TBC are reviewed. Five measurement methods are then compared in terms of their sensitivity to TBC: the 3ω method, frequency- and time-domain thermoreflectance, the cut-bar method, and a composite effective thermal conductivity method. The heart of the review surveys 30 years of TBC measurements around room temperature, highlighting the materials science factors experimentally proven to influence TBC. These factors include the bulk dispersion relations, acoustic contrast, and interfacial chemistry and bonding. The measured TBCs are compared across a wide range of materials systems by using the maximum transmission limit, which with an attenuated transmission coefficient proves to be a good guideline for most clean, strongly bonded interfaces. Finally, opportunities for future research are discussed.

  6. Ultralow Thermal Conductivity in Full Heusler Semiconductors

    Science.gov (United States)

    He, Jiangang; Amsler, Maximilian; Xia, Yi; Naghavi, S. Shahab; Hegde, Vinay I.; Hao, Shiqiang; Goedecker, Stefan; OzoliĆš, Vidvuds; Wolverton, Chris

    2016-07-01

    Semiconducting half and, to a lesser extent, full Heusler compounds are promising thermoelectric materials due to their compelling electronic properties with large power factors. However, intrinsically high thermal conductivity resulting in a limited thermoelectric efficiency has so far impeded their widespread use in practical applications. Here, we report the computational discovery of a class of hitherto unknown stable semiconducting full Heusler compounds with ten valence electrons (X2Y Z , X =Ca , Sr, and Ba; Y =Au and Hg; Z =Sn , Pb, As, Sb, and Bi) through high-throughput ab initio screening. These new compounds exhibit ultralow lattice thermal conductivity κL close to the theoretical minimum due to strong anharmonic rattling of the heavy noble metals, while preserving high power factors, thus resulting in excellent phonon-glass electron-crystal materials.

  7. Workshop on thin film thermal conductivity measurements

    Science.gov (United States)

    Feldman, Albert; Balzaretti, Naira M.; Guenther, Arthur H.

    1998-04-01

    On a subject of considerable import to the laser-induced damage community, a two day workshop on the topic, Thin Film Thermal Conductivity Measurement was held as part of the 13th Symposium on Thermophysical Properties at the University of Colorado in Boulder CO, June 25 and 26, 1997. The Workshop consisted of 4 sessions of 17 oral presentations and two discussion sessions. Two related subjects of interest were covered; 1) methods and problems associated with measuring thermal conductivity ((kappa) ) of thin films, and 2) measuring and (kappa) of chemical vapor deposited (CVD) diamond. On the subject of thin film (kappa) measurement, several recently developed imaginative techniques were reviewed. However, several authors disagreed on how much (kappa) in a film differs from (kappa) in a bulk material of the same nominal composition. A subject of controversy was the definition of an interface. In the first discussion session, several questions were addressed, a principal one being, how do we know that the values of (kappa) we obtain are correct and is there a role for standards in thin film (kappa) measurement. The second discussion session was devoted to a round-robin interlaboratory comparison of (kappa) measurements on a set of CVD diamond specimens and several other specimens of lower thermal conductivity. Large interlaboratory differences obtained in an earlier round robin had been attributed to specimen inhomogeneity. Unfortunately, large differences were also observed in the second round robin even though the specimens were more homogenous. There was good consistency among the DC measurements, however, the AC measurements showed much greater variability. There was positive feedback from most of the attenders regarding the Workshop with nearly all respondents recommending another Workshop in three or fewer years. There was general recognition that thin film thermal conductivity measurements are important for predicting the resistance of optical coating

  8. Evaluation of New Thermally Conductive Geopolymer in Thermal Energy Storage

    Science.gov (United States)

    Černý, Matěj; Uhlík, Jan; Nosek, Jaroslav; Lachman, Vladimír; Hladký, Radim; Franěk, Jan; Brož, Milan

    This paper describes an evaluation of a newly developed thermally conductive geopolymer (TCG), consisting of a mixture of sodium silicate and carbon micro-particles. The TCG is intended to be used as a component of high temperature energy storage (HTTES) to improve its thermal diffusivity. Energy storage is crucial for both ecological and economical sustainability. HTTES plays a vital role in solar energy technologies and in waste heat recovery. The most advanced HTTES technologies are based on phase change materials or molten salts, but suffer with economic and technological limitations. Rock or concrete HTTES are cheaper, but they have low thermal conductivity without incorporation of TCG. It was observed that TCG is stable up to 400 °C. The thermal conductivity was measured in range of 20-23 W m-1 K-1. The effect of TCG was tested by heating a granite block with an artificial fissure. One half of the fissure was filled with TCG and the other with ballotini. 28 thermometers, 5 dilatometers and strain sensors were installed on the block. The heat transport experiment was evaluated with COMSOL Multiphysics software.

  9. Thermal Expansion and Thermal Conductivity of Rare Earth Silicates

    Science.gov (United States)

    Zhu, Dongming; Lee, Kang N.; Bansal, Narottam P.

    2006-01-01

    Rare earth silicates are considered promising candidate materials for environmental barrier coatings applications at elevated temperature for ceramic matrix composites. High temperature thermophysical properties are of great importance for coating system design and development. In this study, the thermal expansion and thermal conductivity of hot-pressed rare earth silicate materials were characterized at temperatures up to 1400 C. The effects of specimen porosity, composition and microstructure on the properties were also investigated. The materials processing and testing issues affecting the measurements will also be discussed.

  10. Measurements of Thermal Conductivity and Thermal Diffusivity of Molten Carbonates

    OpenAIRE

    Wicaksono, Hendro; Zhang, Xing; Fujiwara, Seiji; Fujii, Motoo

    2001-01-01

    The thermal conductivity and thermal diffusivity of molten carbonates (Li_2CO_3/K_2CO_3 and Li_2CO_3/Na_2CO_3) were measured using the transient short-hot-wire method in the temperature range from 530 to 670℃. Two types of probes were examined. One was a platinum short-hot-wire probe coated with alumina (Al_2O_3) thin film to prevent current leakage and corrosion. The other was a bare gold short-hot-wire probe. For the platinum probe, the quality of coating reduces gradually during the measur...

  11. Numerical Simulation of Steady State Conduction Heat Transfer During the Solidification of Aluminum Casting in Green Sand Mould

    Directory of Open Access Journals (Sweden)

    Victor ANJO

    2012-08-01

    Full Text Available The solidification of molten metal during the casting process involves heat transfer from the molten metal to the mould, then to the atmosphere. The mechanical properties and grain size of metals are determined by the heat transfer process during solidification. The aim of this study is to numerically stimulate the steady conduction heat transfer during the solidification of aluminum in green sand mould using finite difference analysis 2D. The properties of materials used are industrial AI 50/60 AFS green sand mould, pure aluminum and MATLAB 7.0.1. for the numerical simulation. The method includes; the finite difference analysis of the heat conduction equation in steady (Laplace’s and transient states and using MATLAB to numerically stimulate the thermal flow and cooling curve. The results obtained are: the steady state thermal flow in 2D and transient state cooling curve of casting. The results obtain were consider relevant in the control of the grain size and mechanical properties of the casting.

  12. Analytical estimation of skeleton thermal conductivity of a geopolymer foam from thermal conductivity measurements

    Science.gov (United States)

    Henon, J.; Alzina, A.; Absi, J.; Smith, D. S.; Rossignol, S.

    2015-07-01

    The geopolymers are alumino-silicate binders. The addition of a high pores volume fraction, gives them a thermal insulation character desired in the building industry. In this work, potassium geopolymer foams were prepared at room temperature (< 70 ∘C) by a process of in situ gas release. The porosity distribution shows a multiscale character. However, the thermal conductivity measurements gave values from 0.35 to 0.12 Wm-1.K-1 for a pore volume fraction values between 65 and 85%. In the aim to predict the thermal properties of these foams and focus on the relationship "thermal-conductivity/microstructure", knowledge of the thermal conductivity of their solid skeleton (λ s ) is paramount. However, there is rare work on the determination of this value depending on the initial composition. By the formulation used, the foaming agent contributes to the final network, and it is not possible to obtain a dense material designate to make a direct measurement of λ s . The objective of this work is to use inverse analytical methods to identify the value of λ s . Measurements of thermal conductivity by the fluxmetre technique were performed. The obtained value of the solid skeleton thermal conductivity by the inverse numerical technique is situated in a framework between 0.95 and 1.35 Wm-1.K-1 and is in agreement with one issue from the literature.

  13. Treating Fibrous Insulation to Reduce Thermal Conductivity

    Science.gov (United States)

    Zinn, Alfred; Tarkanian, Ryan

    2009-01-01

    A chemical treatment reduces the convective and radiative contributions to the effective thermal conductivity of porous fibrous thermal-insulation tile. The net effect of the treatment is to coat the surfaces of fibers with a mixture of transition-metal oxides (TMOs) without filling the pores. The TMO coats reduce the cross-sectional areas available for convection while absorbing and scattering thermal radiation in the pores, thereby rendering the tile largely opaque to thermal radiation. The treatment involves a sol-gel process: A solution containing a mixture of transition-metal-oxide-precursor salts plus a gelling agent (e.g., tetraethylorthosilicate) is partially cured, then, before it visibly gels, is used to impregnate the tile. The solution in the tile is gelled, then dried, and then the tile is fired to convert the precursor salts to the desired mixed TMO phases. The amounts of the various TMOs ultimately incorporated into the tile can be tailored via the concentrations of salts in the solution, and the impregnation depth can be tailored via the viscosity of the solution and/or the volume of the solution relative to that of the tile. The amounts of the TMOs determine the absorption and scattering spectra.

  14. Thermal conductivity of heterogeneous LWR MOX fuels

    Science.gov (United States)

    Staicu, D.; Barker, M.

    2013-11-01

    It is generally observed that the thermal conductivity of LWR MOX fuel is lower than that of pure UO2. For MOX, the degradation is usually only interpreted as an effect of the substitution of U atoms by Pu. This hypothesis is however in contradiction with the observations of Duriez and Philiponneau showing that the thermal conductivity of MOX is independent of the Pu content in the ranges 3-15 and 15-30 wt.% PuO2 respectively. Attributing this degradation to Pu only implies that stoichiometric heterogeneous MOX can be obtained, while we show that any heterogeneity in the plutonium distribution in the sample introduces a variation in the local stoichiometry which in turn has a strong impact on the thermal conductivity. A model quantifying this effect is obtained and a new set of experimental results for homogeneous and heterogeneous MOX fuels is presented and used to validate the proposed model. In irradiated fuels, this effect is predicted to disappear early during irradiation. The 3, 6 and 10 wt.% Pu samples have a similar thermal conductivity. Comparison of the results for this homogeneous microstructure with MIMAS (heterogeneous) fuel of the same composition showed no difference for the Pu contents of 3, 5.9, 6, 7.87 and 10 wt.%. A small increase of the thermal conductivity was obtained for 15 wt.% Pu. This increase is of about 6% when compared to the average of the values obtained for 3, 6 and 10 wt.% Pu. For comparison purposes, Duriez also measured the thermal conductivity of FBR MOX with 21.4 wt.% Pu with O/M = 1.982 and a density close to 95% TD and found a value in good agreement with the estimation obtained using the formula of Philipponneau [8] for FBR MOX, and significantly lower than his results corresponding to the range 3-15 wt.% Pu. This difference in thermal conductivity is of about 20%, i.e. higher than the measurement uncertainties.Thus, a significant difference was observed between FBR and PWR MOX fuels, but was not explained. This difference

  15. Inhomogeneous thermal conductivity enhances thermoelectric cooling

    Directory of Open Access Journals (Sweden)

    Tingyu Lu

    2014-12-01

    Full Text Available We theoretically investigate the enhancement of thermoelectric cooling performance in thermoelectric refrigerators made of materials with inhomogeneous thermal conductivity, beyond the usual practice of enhancing thermoelectric figure of merit (ZT of materials. The dissipation of the Joule heat in such thermoelectric refrigerators is asymmetric which can give rise to better thermoelectric cooling performance. Although the thermoelectric figure of merit and the coefficient-of-performance are slightly enhanced, both the maximum cooling power and the maximum cooling temperature difference can be enhanced significantly. This finding can be used to increase the heat absorption at the cold end. We further find that the asymmetric dissipation of Joule heat leads to thermal rectification.

  16. Sand box experiments with bioclogging of porous media: hydraulic conductivity reductions.

    Science.gov (United States)

    Seifert, Dorte; Engesgaard, Peter

    2012-08-01

    Tracer experiments during clogging and de-clogging experiments in a 2D sand box were via an image analysis used to establish a data set on the relation between changes in hydraulic conductivity (K) and relative porosity (β). Clogging appears to create a finger-like tracer transport, which could be caused by an initial heterogeneous distribution of biomass in the sand box. De-clogging occurs at a slower rate possibly due to the presence of inert biomass that is not affected by the starvation conditions by sudden removal of the substrate source. The tracer front was observed to get disturbed closer and closer to the substrate source during the experiments suggesting that the zone of clogging moved upstream. Three clogging models, K(β), from the literature were tested for their ability to describe the temporal changes in clogging at the scale of the sand box; the model of Clement et al. (1996) that makes no assumption on biomass distribution, the plug formation model of Thullner et al. (2002a), and the biofilm-plug formation model of Vandevivere (1995). The plug formation and biofilm-plug formation models both match the observed changes between the hydraulic conductivity of the sand box and the relative porosity. Unfortunately our experiments did not reach low relative porosities where the two models predict different behaviors. The model by Clement et al. (1996) underestimates clogging.

  17. Evaluation of actual and estimated hydraulic conductivity of sands with different gradation and shape.

    Science.gov (United States)

    Cabalar, Ali Firat; Akbulut, Nurullah

    2016-01-01

    Hydraulic conductivities of sands with different gradation and grain shape were estimated experimentally at a relative density (Dr) of about 40 % and a 22 ± 2 °C of constant temperature. Narli Sand (NS) with 0.67 of sphericity (S) and 0.72 of roundness (R), and Crushed Stone Sand (CSS) with 0.55 of S and 0.15 of R values were artificially graded into sixteen different grain-size fractions (4.75-2, 2-1.18, 1.18-0.6, 0.6-0.425, 0.425-0.3, 0.3-0.075, 4.75-0.075, 2-0.075, 1.18-0.075, 0.6-0.075, 0.425-0.075, 4.75-0.6, 2-0.6, 4.75-0.425, 2-0.425, 1.18-0.425 mm). Hydraulic conductivities of the NS estimated by use of constant head test ranged from 1.61 to 0.01 cm/s, whilst those of the CSS estimated by the same test ranged from 2.45 to 0.012 cm/s. It was observed that the hydraulic conductivity values of the NS are lower than those of the CSS samples, which is likely to be the result of differences in shape, particularly in R values. The results clearly demonstrated that the hydraulic conductivity can be significantly influenced by grading characteristics (d10, d20, d30, d50, d60, cu, cc, n, Io). Furthermore, comparisons between results obtained in the present study and hydraulic conductivity estimated with other formulas available in the literature were made. The comparisons indicated that the best estimation of hydraulic conductivity changes based on the gradation and shape properties of the sands tested.

  18. EVALUATION OF THE BENTONITE CONTENT IN SPENT FOUNDRY SANDS AS A FUNCTION OF HYDRAULIC CONDUCTIVITY COEFFICIENT

    Directory of Open Access Journals (Sweden)

    Schirlene Chegatti

    2013-06-01

    Full Text Available This study evaluates the relationship of the bentonite content and hydraulic conductivity coefficient (k of waste foundry sands in tests of hydraulic conductivity in a flexible wall permeameter. The test samples had concentrations of activated sodium bentonite and natural sodium bentonite between 4% and 15%. It was also analyzed chemically the liquid leachate (aluminum, barium, chromium, cadmium, lead, phenols, iron, fluoride, and manganese, following de standard tests of Standard Methods 3111 B e D for the determination of this components in liquid samples. The experiments were supplemented with cation exchange capacity analysis. The results indicate that the values of are is related to the content of bentonite in waste foundry sand and the percolation from this waste disposal.

  19. 15th International Conference on Thermal Conductivity

    CERN Document Server

    1978-01-01

    Once again, it gives me a great pleasure to pen the Foreword to the Proceedings of the 15th International Conference on Thermal Conductivity. As in the past, these now biannual conferences pro­ vide a broadly based forum for those researchers actively working on this important property of matter to convene on a regular basis to exchange their experiences and report their findings. As it is apparent from the Table of Contents, the 15th Conference represents perhaps the broadest coverage of subject areas to date. This is indicative of the times as the boundaries between disciplines be­ come increasingly diffused. I am sure the time has come when Con­ ference Chairmen in coming years will be soliciting contributions not only in the physical sciences and engineering', but will actively seek contributions from the earth sciences and life sciences as well. Indeed, the thermal conductivity and related properties of geological and biological materials are becoming of increasing im­ portance to our way of life. As...

  20. Thermal Conductivity of Nanotubes: Effects of Chirality and Isotope Impurity

    OpenAIRE

    Gang, Zhang; Li, Baowen

    2005-01-01

    We study the dependence of thermal conductivity of single walled nanotubes (SWNT) on chirality and isotope impurity by nonequilibrium molecular dynamics method with accurate potentials. It is found that, contrary to electronic conductivity, the thermal conductivity is insensitive to the chirality. The isotope impurity, however, can reduce the thermal conductivity up to 60% and change the temperature dependence behavior. We also study the dependence of thermal conductivity on tube length for t...

  1. Effect of Sintering on Thermal Conductivity and Thermal Barrier Effects of Thermal Barrier Coatings

    Institute of Scientific and Technical Information of China (English)

    WANG Kai; PENG Hui; GUO Hongbo; GONG Shengkai

    2012-01-01

    Thermal barrier coatings (TBCs) are mostly applied to hot components of advanced turbine engines to insulate the components from hot gas.The effect of sintering on thermal conductivity and thermal barrier effects of conventional plasma sprayed and nanostructured yttria stabilized zirconia (YSZ) thermal barrier coatings (TBCs) are investigated.Remarkable increase in thermal conductivity occurs to both typical coatings after heat treatment.The change of porosity is just the opposite.The grain size of the nanostructured zirconia coating increases more drastically with annealing time compared to that of the conventional plasma sprayed coating,which indicates that coating sintering makes more contributions to the thermal conductivity of the nanostructured coating than that of the conventional coating.Thermal barrier effect tests using temperature difference technique are performed on both coatings.The thermal barrier effects decrease with the increase of thermal conductivity after heat treatment and the decline seems more drastic in low thermal conductivity range.The decline in thermal barrier effects is about 80 ℃for nanostructured coating after 100 h heat treatment,while the conventional coating reduces by less than 60 ℃ compared to the as-sprayed coating.

  2. Lattice thermal conductivity of LaSe

    Energy Technology Data Exchange (ETDEWEB)

    Li, Wei, E-mail: tolwwt@163.com [School of Physics and Telecommunication Engineering, South China Normal University, 510006 Guangzhou (China); Pan, Zhong-liang; Chen, Jun-fang; He, Qin-yu [School of Physics and Telecommunication Engineering, South China Normal University, 510006 Guangzhou (China); Wang, Teng [School of Computer, South China Normal University, 510631 Guangzhou (China)

    2015-07-15

    The phonon dispersions and phonon density of states of LaSe are obtained, based on density functional perturbation theory and the norm-conserving pseudo-potential method. An anomaly in calculated phonon dispersion curves is presented and interpreted as a Kohn anomaly. The heat capacity of LaSe is calculated then. For the three-phonon process scattering, the lowest non-harmonic cubic terms of the interatomic potential are considered to obtain single-phonon relaxation rate by applying the Fermi's golden rule. For the boundary scattering, the average phonon relaxation time was obtained. Considering two kinds of phonon scattering mechanisms, we obtain the lattice thermal conductivity of LaSe.

  3. Thermal Conductivity of Carbon Nanoreinforced Epoxy Composites

    Directory of Open Access Journals (Sweden)

    C. Kostagiannakopoulou

    2016-01-01

    Full Text Available The present study attempts to investigate the influence of multiwalled carbon nanotubes (MWCNTs and graphite nanoplatelets (GNPs on thermal conductivity (TC of nanoreinforced polymers and nanomodified carbon fiber epoxy composites (CFRPs. Loading levels from 1 to 3% wt. of MWCNTs and from 1 to 15% wt. of GNPs were used. The results indicate that TC of nanofilled epoxy composites increased with the increase of GNP content. Quantitatively, 176% and 48% increase of TC were achieved in nanoreinforced polymers and nanomodified CFRPs, respectively, with the addition of 15% wt. GNPs into the epoxy matrix. Finally, micromechanical models were applied in order to predict analytically the TC of polymers and CFRPs. Lewis-Nielsen model with optimized parameters provides results very close to the experimental ones in the case of polymers. As far as the composites are concerned, the Hashin and Clayton models proved to be sufficiently accurate for the prediction at lower filler contents.

  4. Undergraduate Study of Thermal Conductivity of Metals

    Directory of Open Access Journals (Sweden)

    Ferrari T. B.

    2002-01-01

    Full Text Available In this work we analyze an undergraduate experiment used to determine the thermal conductivity of metals (K. We introduce few modifications in order to offer the student the chance to explore dierent models, learning the basic scientiffic method of developing appropriate and improved explanations for each experiment in order to better link theory and empirical results. Semi-empirical corrections are introduced in the system in order to check the experimental results according to previously reported K values. As specific cases we use copper [K = 0.92 cal /(°C s cm], aluminum [K = 0.49 cal /(°C s cm] and brass [K = 0.26 cal /(°C s cm] cylinders.

  5. On non-extensive nature of thermal conductivity

    Indian Academy of Sciences (India)

    Ashok Razdan

    2007-01-01

    In this paper we study non-extensive nature of thermal conductivity. It is observed that there is similarity between non-extensive entropic index and fractal dimension obtained for the silica aerogel thermal conductivity data at low temperature.

  6. High-Thermal Conductive Coating Used on Metal Heat Exchanger

    Institute of Scientific and Technical Information of China (English)

    李静; 梁剧; 刘业明

    2014-01-01

    Based on modified silicon polyester resin in addition to several functional fillers such as corro-sion-resistant fillers, heat-resistant fillers and thermal conductive fillers, a high thermal conductive coating can be made. On the basis of boronnitride (BN) and aluminum nitride (AIN) used as thermal conductive fillers and by means of the testing system of hot disk and heat transfer experiment, researches on the varieties of thermal conduc-tive fillers and the effects of the contents of high-thermal conductive coating have been done, which shows that the thermal conductivity of coating increases with the increase of the quality fraction and the coefficient of thermal conductivity of the thermal conductive fillers of coating. With guaranteeing better heat resistance, stronger corro-sion resistance and adhesive force, the coefficient of coating can reach a level as high as 3 W·m-1·K-1.

  7. Mean free path dependent phonon contributions to interfacial thermal conductance

    Science.gov (United States)

    Tao, Yi; Liu, Chenhan; Chen, Weiyu; Cai, Shuang; Chen, Chen; Wei, Zhiyong; Bi, Kedong; Yang, Juekuan; Chen, Yunfei

    2017-06-01

    Interfacial thermal conductance as an accumulation function of the phonon mean free path is rigorously derived from the thermal conductivity accumulation function. Based on our theoretical model, the interfacial thermal conductance accumulation function between Si/Ge is calculated. The results show that the range of mean free paths (MFPs) for phonons contributing to the interfacial thermal conductance is far narrower than that for phonons contributing to the thermal conductivity. The interfacial thermal conductance is mainly contributed by phonons with shorter MFPs, and the size effects can be observed only for an interface constructed by nanostructures with film thicknesses smaller than the MFPs of those phonons mainly contributing to the interfacial thermal conductance. This is why most experimental measurements cannot detect size effects on interfacial thermal conductance. A molecular dynamics simulation is employed to verify our proposed model.

  8. Method for Measuring Thermal Conductivity of Small Samples Having Very Low Thermal Conductivity

    Science.gov (United States)

    Miller, Robert A.; Kuczmarski, Maria a.

    2009-01-01

    This paper describes the development of a hot plate method capable of using air as a standard reference material for the steady-state measurement of the thermal conductivity of very small test samples having thermal conductivity on the order of air. As with other approaches, care is taken to ensure that the heat flow through the test sample is essentially one-dimensional. However, unlike other approaches, no attempt is made to use heated guards to block the flow of heat from the hot plate to the surroundings. It is argued that since large correction factors must be applied to account for guard imperfections when sample dimensions are small, it may be preferable to simply measure and correct for the heat that flows from the heater disc to directions other than into the sample. Experimental measurements taken in a prototype apparatus, combined with extensive computational modeling of the heat transfer in the apparatus, show that sufficiently accurate measurements can be obtained to allow determination of the thermal conductivity of low thermal conductivity materials. Suggestions are made for further improvements in the method based on results from regression analyses of the generated data.

  9. Identification of interfacial heat transfer between molten metal and green sand by inverse heat conduction method

    Science.gov (United States)

    Ke, Quanpeng

    Heat flux and heat transfer coefficients at the interfaces of castings and molds are important parameters in the mold design and computer simulations of the solidification process in foundry operations. A better understanding of the heat flux and heat transfer coefficient between the solidifying casting and its mold can promote model design and improve the accuracy of computer simulation. The main purpose of the present dissertation involves the estimation of the heat flux and heat transfer coefficient at the interface of the molten metal and green sand. Since the inverse heat conduction method requires temperature measurement data to deduce the missing surface information, it is suitable for the present research. However, heat transfer inside green sand is complicated by the migration of water vapor and zonal temperature distribution results. This makes the solution of the inverse heat conduction problem more challenging. In this dissertation, Galerkin's method of Weighted Residual together with the front tracking technique is used in the development of a forward solver. Beck's future time step method incorporated with the Gaussian iterative minimization method is used as the inverse solver. The mathematical descriptions of the sensitivity coefficient for both the direct heat flux and direct heat transfer coefficient estimation are derived. The variations of the sensitivity coefficients with time are revealed. From the analysis of sensitivity coefficients, the concept of blank time period is proposed. This blank time period makes the inverse problem much more difficult. A total energy balance criterion is used to combat this. Numerical experiments confirmed the accuracy and robustness of both the direct heat flux estimation algorithm and the direct heat transfer coefficient estimation algorithm. Finally, some pouring experiments are carried out. The inverse algorithms are applied to the estimation of the heat flux and heat transfer coefficient at the interface of

  10. Measurement of in-plane thermal conductivity in polymer films

    National Research Council Canada - National Science Library

    Wei, Qingshuo; Uehara, Chinatsu; Mukaida, Masakazu; Kirihara, Kazuhiro; Ishida, Takao

    2016-01-01

    .... We evaluated thermal conductivities and anisotropic ratios for various types of samples including insulating polymers, undoped semiconducting polymers, doped conducting polymers, and one-dimensional...

  11. Thermal conductance in a two-slit quantum waveguide

    Institute of Scientific and Technical Information of China (English)

    Nie Liu-Ying; Li Chun-Xian; Zhou Xiao-Ping; Wang Cheng-Zhi; Cheng Fang

    2012-01-01

    Using the scattering-matrix method,we investigate the thermal conductance in a two-slit quantum waveguide at low temperature.The results show that the total thermal conductance decreases monotonically with temperature increasing. Moreover,we find that the behaviours of the thermal conductance versus temperature are different for different types of slits.

  12. Strain-controlled thermal conductivity in ferroic twinned films

    Science.gov (United States)

    Li, Suzhi; Ding, Xiangdong; Ren, Jie; Moya, Xavier; Li, Ju; Sun, Jun; Salje, Ekhard K. H.

    2014-09-01

    Large reversible changes of thermal conductivity are induced by mechanical stress, and the corresponding device is a key element for phononics applications. We show that the thermal conductivity κ of ferroic twinned thin films can be reversibly controlled by strain. Nonequilibrium molecular dynamics simulations reveal that thermal conductivity decreases linearly with the number of twin boundaries perpendicular to the direction of heat flow. Our demonstration of large and reversible changes in thermal conductivity driven by strain may inspire the design of controllable thermal switches for thermal logic gates and all-solid-state cooling devices.

  13. Thermal conductivity of Cu–4.5 Ti alloy

    Indian Academy of Sciences (India)

    S Nagarjuna

    2004-02-01

    The thermal conductivity (TC) of peak aged Cu–4.5 wt% Ti alloy was measured at different temperatures and studied its variation with temperature. It was found that TC increased with increasing temperature. Phonon and electronic components of thermal conductivity were computed from the results. The alloy exhibits an electronic thermal conductivity of 46.45 W/m.K at room temperature. The phonon thermal conductivity decreased with increasing temperature from 17.6 at 0 K to 1.75 W/m.K at 298 K, which agrees with literature that the phonon component of thermal conductivity is insignificant at room temperature.

  14. Four-terminal thermal conductance of mesoscopic dielectric systems.

    Science.gov (United States)

    Sun, Qing-Feng; Yang, Ping; Guo, Hong

    2002-10-21

    A four-terminal thermal conductance formula for a mesoscopic dielectric system with arbitrary central scattering region is derived. Similar to four-terminal electric conductance, the four-terminal thermal conductance also has a set of Onsager relations. In the temperature T-->0 limit, in contrast to the two-terminal thermal conductance which is a monotonic function of T and tends to zero, the four-terminal thermal conductance is nonmonotonic and tends to infinity. We also find that temperatures of the two terminals without thermal flux become very close to each other at low temperatures. Rather different behaviors are found for systems satisfying fractional exclusion statistics.

  15. Effect of thermal diffusion and electrostatic force on evolution of wind-blown sand flow

    Institute of Scientific and Technical Information of China (English)

    YUE Gao-wei; ZHENG Xiao-jing

    2007-01-01

    A theoretical model is suggested to mathematically describe the effect of thermal diffusion from a sand-bed on evolution of a wind-blown sand flow. An upward wind field is engendered by the thermal diffusion and the coupling interaction among the horizontal and upward wind flow, saltating grains, and a kind of electrostatic force exerted on the grains are considered in this theoretical model. The numerical results show that the effect of the thermal diffusion on the evolution process of wind-blown grain flow is quite obvious and very similar to the effect of the electrostatic force on the evolution. Not only the time for the entire system to reach a steady state (called the duration time), the transport rate of grains, the mass-flux profiles and the trajectory of saltating grains are affected by the thermal diffusion and the electrostatic force exerted on saltating grains,but also the wind profiles and the temperature profiles at the steady state are affected by the wind-blown sand flow.

  16. Multiscale modeling of thermal conductivity of polycrystalline graphene sheets.

    Science.gov (United States)

    Mortazavi, Bohayra; Pötschke, Markus; Cuniberti, Gianaurelio

    2014-03-21

    We developed a multiscale approach to explore the effective thermal conductivity of polycrystalline graphene sheets. By performing equilibrium molecular dynamics (EMD) simulations, the grain size effect on the thermal conductivity of ultra-fine grained polycrystalline graphene sheets is investigated. Our results reveal that the ultra-fine grained graphene structures have thermal conductivity one order of magnitude smaller than that of pristine graphene. Based on the information provided by the EMD simulations, we constructed finite element models of polycrystalline graphene sheets to probe the thermal conductivity of samples with larger grain sizes. Using the developed multiscale approach, we also investigated the effects of grain size distribution and thermal conductivity of grains on the effective thermal conductivity of polycrystalline graphene. The proposed multiscale approach on the basis of molecular dynamics and finite element methods could be used to evaluate the effective thermal conductivity of polycrystalline graphene and other 2D structures.

  17. Finite-element technique applied to heat conduction in solids with temperature dependent thermal conductivity

    Science.gov (United States)

    Aguirre-Ramirez, G.; Oden, J. T.

    1969-01-01

    Finite element method applied to heat conduction in solids with temperature dependent thermal conductivity, using nonlinear constitutive equation for heat ABCDEFGHIABCDEFGHIABCDEFGHIABCDEFGHIABCDEFGHIABCDEFGHIABCDEFGHIABCDEFGHIABCDEFGHIABCDEFGHIABCDEFGHIABCDEFGH

  18. Plane waves in a thermally conducting viscous liquid

    Indian Academy of Sciences (India)

    Baljeet Singh

    2004-02-01

    The aim of this paper is to investigate plane waves in a thermally conducting viscous liquid half-space with thermal relaxation times. There exist three basic waves, namely; thermal wave, longitudinal wave and transverse wave in a thermally conducting viscous liquid half-space. Reflection of plane waves from the free surface of a thermally conducting viscous liquid half-space is studied. The results are obtained in terms of amplitude ratios and are compared with those without viscosity and thermal disturbances.

  19. Determination of thermal conductivity of magnesium-alloys

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    An indirect method, Angstroms method was adopted and an instrument was designed to determine the thermal conductivity of magnesium metal and alloys. Angstroms method is an axial periodic heat flow technique by which the thermal diffusivity can be measured directly. Then thermal conductivity can be obtained with relation to thermal diffusivity. Compared with the recommended data from the literature the fitted values of the thermal diffiusivity correspond with 3%, and the credible probability of the thermal conductivity in the range of 0-450 ℃ is about 95%. The method is applicable in the given temperature range.

  20. Thermal Properties of Asphalt Mixtures Modified with Conductive Fillers

    Directory of Open Access Journals (Sweden)

    Byong Chol Bai

    2015-01-01

    Full Text Available This paper investigates the thermal properties of asphalt mixtures modified with conductive fillers used for snow melting and solar harvesting pavements. Two different mixing processes were adopted to mold asphalt mixtures, dry- and wet-mixing, and two conductive fillers were used in this study, graphite and carbon black. The thermal conductivity was compared to investigate the effects of asphalt mixture preparing methods, the quantity, and the distribution of conductive filler on thermal properties. The combination of conductive filler with carbon fiber in asphalt mixture was evaluated. Also, rheological properties of modified asphalt binders with conductive fillers were measured using dynamic shear rheometer and bending beam rheometer at grade-specific temperatures. Based on rheological testing, the conductive fillers improve rutting resistance and decrease thermal cracking resistance. Thermal testing indicated that graphite and carbon black improve the thermal properties of asphalt mixes and the combined conductive fillers are more effective than the single filler.

  1. Mean-field versus microconvection effects in nanofluid thermal conduction.

    Science.gov (United States)

    Eapen, Jacob; Williams, Wesley C; Buongiorno, Jacopo; Hu, Lin-Wen; Yip, Sidney; Rusconi, Roberto; Piazza, Roberto

    2007-08-31

    Transient hot-wire data on thermal conductivity of suspensions of silica and perfluorinated particles show agreement with the mean-field theory of Maxwell but not with the recently postulated microconvection mechanism. The influence of interfacial thermal resistance, convective effects at microscales, and the possibility of thermal conductivity enhancements beyond the Maxwell limit are discussed.

  2. Mean-Field Versus Microconvection Effects in Nanofluid Thermal Conduction

    Science.gov (United States)

    Eapen, Jacob; Williams, Wesley C.; Buongiorno, Jacopo; Hu, Lin-Wen; Yip, Sidney; Rusconi, Roberto; Piazza, Roberto

    2007-08-01

    Transient hot-wire data on thermal conductivity of suspensions of silica and perfluorinated particles show agreement with the mean-field theory of Maxwell but not with the recently postulated microconvection mechanism. The influence of interfacial thermal resistance, convective effects at microscales, and the possibility of thermal conductivity enhancements beyond the Maxwell limit are discussed.

  3. Thermal Conductivity of Carbon Nanotubes Embedded in Solids

    Institute of Scientific and Technical Information of China (English)

    CAO Bing-Yang; HOU Quan-Wen

    2008-01-01

    @@ A carbon-nanotube-atom fixed and activated scheme of non-equilibrium molecular dynamics simulations is put forward to extract the thermal conductivity of carbon nanotubes (CNTs) embedded in solid argon. Though a 6.5% volume fraction of CNTs increases the composite thermal conductivity to about twice as much as that of the pure basal material, the thermal conductivity of CNTs embedded in solids is found to be decreased by 1/8-1/5with reference to that of pure ones. The decrease of the intrinsic thermal conductivity of the solid-embedded CNTs and the thermal interface resistance are demonstrated to be responsible for the results.

  4. Micromachined hot-wire thermal conductivity probe for biomedical applications.

    Science.gov (United States)

    Yi, Ming; Panchawagh, Hrishikesh V; Podhajsky, Ronald J; Mahajan, Roop L

    2009-10-01

    This paper presents the design, fabrication, numerical simulation, and experimental validation of a micromachined probe that measures thermal conductivity of biological tissues. The probe consists of a pair of resistive line heating elements and resistance temperature detector sensors, which were fabricated by using planar photolithography on a glass substrate. The numerical analysis revealed that the thermal conductivity and diffusivity can be determined by the temperature response induced by the uniform heat flux in the heating elements. After calibrating the probe using a material (agar gel) of known thermal conductivity, the probe was deployed to calculate the thermal conductivity of Crisco. The measured value is in agreement with that determined by the macro-hot-wire probe method to within 3%. Finally, the micro thermal probe was used to investigate the change of thermal conductivity of pig liver before and after RF ablation treatment. The results show an increase in thermal conductivity of liver after the RF ablation.

  5. The Measurement of Thermal Conductivities of Silica and Carbon Black Powders at Different pressures by Thermal COnductivity Probe

    Institute of Scientific and Technical Information of China (English)

    X.G.Liang; X.S.Ge; 等

    1992-01-01

    This investigation was done to study the gas filled powder insulation and thermal conductivity probe for the measurent of thermal conductivity of powders.The mathematical analysis showed that the heat capacity of the probe itself and the thermal rsistance between the probe and powder must be considered .The authors developed a slender probe and measured the effective thermal conductivity of sillca and carbon black powders under a variety of conditions.

  6. Thermal conductivity of silicon nanocrystals and polystyrene nanocomposite thin films

    Science.gov (United States)

    Bagja Juangsa, Firman; Muroya, Yoshiki; Ryu, Meguya; Morikawa, Junko; Nozaki, Tomohiro

    2016-09-01

    Silicon nanocrystals (SiNCs) are well known for their size-dependent optical and electronic properties; they also have the potential for low yet controllable thermal properties. As a silicon-based low-thermal conductivity material is required in microdevice applications, SiNCs can be utilized for thermal insulation. In this paper, SiNCs and polymer nanocomposites were produced, and their thermal conductivity, including the density and specific heat, was measured. Measurement results were compared with thermal conductivity models for composite materials, and the comparison shows a decreasing value of the thermal conductivity, indicating the effect of the size and presence of the nanostructure on the thermal conductivity. Moreover, employing silicon inks at room temperature during the fabrication process enables a low cost of fabrication and preserves the unique properties of SiNCs.

  7. THERMAL CONDUCTIVITY OF RUBBERIZED GYPSUM BOARD

    OpenAIRE

    Taher Abu-Lebdeh; Ellie Fini; Ashraf Fadiel

    2014-01-01

    The disposal of scrap tires is a challenging task and hence an innovative solution to meet these challenges is needed. Extensive work has been done on the utilization of waste tires in a variety of applications in asphalt pavements and concrete. However, previous investigations focus only on the mechanical properties of the rubberized materials, but few on the thermal performance. This is especially true for rubberized gypsum. Limited or no experimental data on the thermal performance of rubb...

  8. Thermal conductivity measurement in clay dominant consolidated material by Transient Hot-Wire method.

    Science.gov (United States)

    Garnier, J. P.; Gallier, J.; Mercx, B.; Dudoignon, P.; Milcent, D.

    2010-06-01

    The transient hot-wire (THW) technique is widely used for measurements of the thermal-conductivity of most fluids and some attempts have also been carried out for simultaneous measurements of the thermal-diffusivity with the same hot wire. This technique was also tried to determine thermal properties of soils by the mean of probes which can be considered as wire with some assumptions. The purpose of this paper is to validate the thermal conductivity measurement by the THW technique in geomaterials, composed of compacted sand + clay mineral that can be used for earth construction (Compacted Earth Brick). The thermal transfer behaviors are mainly governed by the texture and moisture of the geomaterials. Thus the investigations were performed (1) in media made of glass beads of different diameters in dry and saturated state in order to observe the role of grain sizes and saturation state on the wire temperature (Δt) measurements and (2) in the compacted clay-geomaterial at different moisture states. The Δt / ln(t) diagrams allow the calculation of two thermal conductivities. The first one, measured in the short time acquisition (thermal conductivity of the material.

  9. Thermal conductivity measurement in clay dominant consolidated material by Transient Hot-Wire method.

    Directory of Open Access Journals (Sweden)

    Milcent D.

    2010-06-01

    Full Text Available The transient hot-wire (THW technique is widely used for measurements of the thermal-conductivity of most fluids and some attempts have also been carried out for simultaneous measurements of the thermal-diffusivity with the same hot wire. This technique was also tried to determine thermal properties of soils by the mean of probes which can be considered as wire with some assumptions. The purpose of this paper is to validate the thermal conductivity measurement by the THW technique in geomaterials, composed of compacted sand + clay mineral that can be used for earth construction (Compacted Earth Brick. The thermal transfer behaviors are mainly governed by the texture and moisture of the geomaterials. Thus the investigations were performed (1 in media made of glass beads of different diameters in dry and saturated state in order to observe the role of grain sizes and saturation state on the wire temperature (Δt measurements and (2 in the compacted clay-geomaterial at different moisture states. The Δt / ln(t diagrams allow the calculation of two thermal conductivities. The first one, measured in the short time acquisition (< 1s, characterizes the microtexture of the material and its hydrated state. The second one, measured for longer time acquisitions, characterizes the mean thermal conductivity of the material.

  10. Model for thermal conductivity of CNT-nanofluids

    Indian Academy of Sciences (India)

    H E Patel; K B Anoop; T Sundararajan; Sarit K Das

    2008-06-01

    This work presents a simple model for predicting the thermal conductivity of carbon nanotube (CNT) nanofluids. Effects due to the high thermal conductivity of CNTs and the percolation of heat through it are considered to be the most important reasons for their anomalously high thermal conductivity enhancement. A new approach is taken for the modeling, the novelty of which lies in the prediction of the thermal behaviour of oil based as well as water based CNT nanofluids, which are quite different from each other in thermal characteristics. The model is found to correctly predict the trends observed in experimental data for different combinations of CNT nanofluids with varying concentrations.

  11. Tuning thermal conductivity in molybdenum disulfide by electrochemical intercalation

    Science.gov (United States)

    Zhu, Gaohua; Liu, Jun; Zheng, Qiye; Zhang, Ruigang; Li, Dongyao; Banerjee, Debasish; Cahill, David G.

    2016-10-01

    Thermal conductivity of two-dimensional (2D) materials is of interest for energy storage, nanoelectronics and optoelectronics. Here, we report that the thermal conductivity of molybdenum disulfide can be modified by electrochemical intercalation. We observe distinct behaviour for thin films with vertically aligned basal planes and natural bulk crystals with basal planes aligned parallel to the surface. The thermal conductivity is measured as a function of the degree of lithiation, using time-domain thermoreflectance. The change of thermal conductivity correlates with the lithiation-induced structural and compositional disorder. We further show that the ratio of the in-plane to through-plane thermal conductivity of bulk crystal is enhanced by the disorder. These results suggest that stacking disorder and mixture of phases is an effective mechanism to modify the anisotropic thermal conductivity of 2D materials.

  12. Rapid thermal conductivity measurements for combinatorial thin films.

    Science.gov (United States)

    McDowell, Matthew G; Hill, Ian G

    2013-05-01

    A simple and inexpensive automated method for determining the thermal conductivity of a combinatorial library of thin films is demonstrated by measuring the thermal conductivity of a sputtered silicon dioxide film of varying thickness deposited on single crystal silicon. Using 3ω measurements, two methods for calculating the substrate thermal conductivity and two methods for determining the film thermal conductivity are demonstrated and compared. The substrate thermal conductivity was found to be 139 ± 3 W/m·K. Using the measured variation in film thickness, the film thermal conductivity was found to be 1.11 ± 0.05 W/m·K, in excellent agreement with published values for sputtered SiO2, demonstrating the accuracy of the method.

  13. Tuning thermal conductivity in molybdenum disulfide by electrochemical intercalation.

    Science.gov (United States)

    Zhu, Gaohua; Liu, Jun; Zheng, Qiye; Zhang, Ruigang; Li, Dongyao; Banerjee, Debasish; Cahill, David G

    2016-10-21

    Thermal conductivity of two-dimensional (2D) materials is of interest for energy storage, nanoelectronics and optoelectronics. Here, we report that the thermal conductivity of molybdenum disulfide can be modified by electrochemical intercalation. We observe distinct behaviour for thin films with vertically aligned basal planes and natural bulk crystals with basal planes aligned parallel to the surface. The thermal conductivity is measured as a function of the degree of lithiation, using time-domain thermoreflectance. The change of thermal conductivity correlates with the lithiation-induced structural and compositional disorder. We further show that the ratio of the in-plane to through-plane thermal conductivity of bulk crystal is enhanced by the disorder. These results suggest that stacking disorder and mixture of phases is an effective mechanism to modify the anisotropic thermal conductivity of 2D materials.

  14. Thermal conductivity degradation of graphites irradiated at low temperature

    Energy Technology Data Exchange (ETDEWEB)

    Snead, L.L.; Burchell, T.D. [Oak Ridge National Lab., TN (United States)

    1995-04-01

    The objective of this work is to study the thermal conductivity degradation of new, high thermal conductivity graphites and to compare these results to more standard graphites irradiated at low temperatures. Several graphites and graphite composites (C/C`s) have been irradiated near 150{degree}C and at fluences up to a displacement level of 0.24 dpa. The materials ranged in unirradiated room temperature thermal conductivity of these materials varied from 114 W/m-K for H-451 isotropic graphite, to 670 W/m-K for unidirectional FMI-1D C/C composite. At the irradiation temperature a saturation reduction in thermal conductivity was seen to occur at displacement levels of approximately 0.1 dpa. All materials were seen to degrade to approximately 10 to 14 % of their original thermal conductivity after irradiation. The effect of post irradiation annealing on the thermal conductivity was also studied.

  15. Tuning thermal conductivity in molybdenum disulfide by electrochemical intercalation

    Science.gov (United States)

    Zhu, Gaohua; Liu, Jun; Zheng, Qiye; Zhang, Ruigang; Li, Dongyao; Banerjee, Debasish; Cahill, David G.

    2016-01-01

    Thermal conductivity of two-dimensional (2D) materials is of interest for energy storage, nanoelectronics and optoelectronics. Here, we report that the thermal conductivity of molybdenum disulfide can be modified by electrochemical intercalation. We observe distinct behaviour for thin films with vertically aligned basal planes and natural bulk crystals with basal planes aligned parallel to the surface. The thermal conductivity is measured as a function of the degree of lithiation, using time-domain thermoreflectance. The change of thermal conductivity correlates with the lithiation-induced structural and compositional disorder. We further show that the ratio of the in-plane to through-plane thermal conductivity of bulk crystal is enhanced by the disorder. These results suggest that stacking disorder and mixture of phases is an effective mechanism to modify the anisotropic thermal conductivity of 2D materials. PMID:27767030

  16. Universal Features of Quantized Thermal Conductance of Carbon Nanotubes

    OpenAIRE

    Yamamoto, Takahiro; Watanabe, Satoshi; Watanabe, Kazuyuki

    2003-01-01

    The universal features of quantized thermal conductance of carbon nanotubes (CNTs) are revealed through theoretical analysis based on the Landauer theory of heat transport. The phonon-derived thermal conductance of semiconducting CNTs exhibits a universal quantization in the low temperature limit, independent of the radius or atomic geometry. The temperature dependence follows a single curve given in terms of temperature scaled by the phonon energy gap. The thermal conductance of metallic CNT...

  17. Thermal conductivity of nickel superalloy MAR-M247

    OpenAIRE

    P. Jonšta; Koštial, P.; Jonšta, Z.; Vlčková, I.; T. Kulová

    2016-01-01

    The paper presents the narrow connection between γ’ phase dissolving and values of thermal conductivity. In annealing process the free space among γ’ particles (blocks) changes in certain cycle from fine to rough and back to fine. This is accompanied by decrease and subsequent increase of thermal conductivity as well as the sample density. The results of thermal conductivity coarse are supported by image analysis. Web of Science 55 3 422 420

  18. Experimental Study to Find Thermal Conductivity Coefficient for Concrete Mixed with Styropor

    Directory of Open Access Journals (Sweden)

    Atalah H. Jassem

    2013-05-01

    Full Text Available Thermal insulation properties of a blend mixture composed of different percentages (50% ,60% ,70% and 80% of styropor with concrete and sand of equal volumetric percentages 15%, 20%, 25%,and 10% respectively. This study includes calibration of instruments for measuring the heat transferred through  samples and investigating the way that used for calculating the proportions of mixing for each sample.            Finally the experiments were conducted in order to determine the correlation of thermal conductivity of each sample with its mean temperature.            It was demonstrated that the new mixture has good rank of thermal properties among the other insulators, with thermal conductivity of 0.3 w/m.oC. This value is lower than the mean value of thermal conductivity values of concrete insulators in the buildings.            Experiments are carried out under a temperature range of (14- 70 oC and under different volumetric proportions of the mixture.63            The experimental results showed that the behavior of the thermal conductivity with the mean temperature on the two faces of the sample is directly proportional like the other insulators.

  19. Molecular dynamics simulation of thermal conductivities of superlattice nanowires

    Institute of Scientific and Technical Information of China (English)

    杨决宽; 陈云飞; 颜景平

    2003-01-01

    Nonequilibrium molecular dynamics simulations were carried out to investigate heat transfer in superlattice nanowires. Results show that for fixed period length superlattice nanowires, the ratio of the total interfacial thermal resistance to the total thermal resistance and the effective thermal conductivities are invariant with the changes in interface numbers. Increasing the period length leads to an increase in the average interfacial thermal resistance, which indicates that the interfacial thermal resistance depends not only on the materials that constitute the alternating segments of superlattice nanowires, but also on the lattice strain throughout the segments. The modification of the lattice structure due to the lattice mismatch should be taken into account in the acoustic mismatch model. Simulation results also demonstrated the size confinement effect on the thermal conductivities for low dimensional structures, i.e. the thermal conductivities and the interfacial thermal resistance increase as the nanowire cross-sectional area increases.

  20. Enhanced thermal conductance of polymer composites through embeddingaligned carbon nanofibers

    Directory of Open Access Journals (Sweden)

    Dale K. Hensley

    2016-07-01

    Full Text Available The focus of this work is to find a more efficient method of enhancing the thermal conductance of polymer thin films. This work compares polymer thin films embedded with randomly oriented carbon nanotubes to those with vertically aligned carbon nanofibers. Thin films embedded with carbon nanofibers demonstrated a similar thermal conductance between 40–60 μm and a higher thermal conductance between 25–40 μm than films embedded with carbon nanotubes with similar volume fractions even though carbon nanotubes have a higher thermal conductivity than carbon nanofibers.

  1. Reduced thermal conductivity of isotopically modulated silicon multilayer structures

    DEFF Research Database (Denmark)

    Bracht, H.; Wehmeier, N.; Eon, S.;

    2012-01-01

    We report measurements of the thermal conductivity of isotopically modulated silicon that consists of alternating layers of highly enriched silicon-28 and silicon-29. A reduced thermal conductivity of the isotopically modulated silicon compared to natural silicon was measured by means of time......-resolved x-ray scattering. Comparison of the experimental results to numerical solutions of the corresponding heat diffusion equations reveals a factor of three lower thermal conductivity of the isotope structure compared to natural Si. Our results demonstrate that the thermal conductivity of silicon can...

  2. Thermal Conductivity of Alumina-Toughened Zirconia Composites

    Science.gov (United States)

    Bansal, Narottam P.; Zhu, Dong-Ming

    2003-01-01

    10-mol% yttria-stabilized zirconia (10YSZ)-alumina composites containing 0 to 30 mol% alumina were fabricated by hot pressing at 1500 C in vacuum. Thermal conductivity of the composites, determined at various temperatures using a steady-state laser heat flux technique, increased with increase in alumina content. Composites containing 0, 5, and 10-mol% alumina did not show any change in thermal conductivity with temperature. However, those containing 20 and 30-mol% alumina showed a decrease in thermal conductivity with increase in temperature. The measured values of thermal conductivity were in good agreement with those calculated from simple rule of mixtures.

  3. Thermal Conductivity Measurement of Anisotropic Biological Tissue In Vitro

    Science.gov (United States)

    Yue, Kai; Cheng, Liang; Yang, Lina; Jin, Bitao; Zhang, Xinxin

    2017-06-01

    The accurate determination of the thermal conductivity of biological tissues has implications on the success of cryosurgical/hyperthermia treatments. In light of the evident anisotropy in some biological tissues, a new modified stepwise transient method was proposed to simultaneously measure the transverse and longitudinal thermal conductivities of anisotropic biological tissues. The physical and mathematical models were established, and the analytical solution was derived. Sensitivity analysis and experimental simulation were performed to determine the feasibility and measurement accuracy of simultaneously measuring the transverse and longitudinal thermal conductivities. The experimental system was set up, and its measurement accuracy was verified by measuring the thermal conductivity of a reference standard material. The thermal conductivities of the pork tenderloin and bovine muscles were measured using the traditional 1D and proposed methods, respectively, at different temperatures. Results indicate that the thermal conductivities of the bovine muscle are lower than those of the pork tenderloin muscle, whereas the bovine muscle was determined to exhibit stronger anisotropy than the pork tenderloin muscle. Moreover, the longitudinal thermal conductivity is larger than the transverse thermal conductivity for the two tissues and all thermal conductivities increase with the increase in temperature. Compared with the traditional 1D method, results obtained by the proposed method are slightly higher although the relative deviation is below 5 %.

  4. Thermal conductivity of penta-graphene from molecular dynamics study.

    Science.gov (United States)

    Xu, Wen; Zhang, Gang; Li, Baowen

    2015-10-21

    Using classical equilibrium molecular dynamics simulations and applying the original Tersoff interatomic potential, we study the thermal transport property of the latest two dimensional carbon allotrope, penta-graphene. It is predicted that its room-temperature thermal conductivity is about 167 W/mK, which is much lower than that of graphene. With normal mode decomposition, the accumulated thermal conductivity with respect to phonon frequency and mean free path is analyzed. It is found that the acoustic phonons make a contribution of about 90% to the thermal conductivity, and phonons with mean free paths larger than 100 nm make a contribution over 50%. We demonstrate that the remarkably lower thermal conductivity of penta-graphene compared with graphene results from the lower phonon group velocities and fewer collective phonon excitations. Our study highlights the importance of structure-property relationship and provides better understanding of thermal transport property and valuable insight into thermal management of penta-graphene.

  5. Tailoring thermal conductivity via three-dimensional porous alumina

    Science.gov (United States)

    Abad, Begoña; Maiz, Jon; Ruiz-Clavijo, Alejandra; Caballero-Calero, Olga; Martin-Gonzalez, Marisol

    2016-12-01

    Three-dimensional anodic alumina templates (3D-AAO) are an astonishing framework with open highly ordered three-dimensional skeleton structures. Since these templates are architecturally different from conventional solids or porous templates, they teem with opportunities for engineering thermal properties. By establishing the mechanisms of heat transfer in these frameworks, we aim to create materials with tailored thermal properties. The effective thermal conductivity of an empty 3D-AAO membrane was measured. As the effective medium theory was not valid to extract the skeletal thermal conductivity of 3D-AAO, a simple 3D thermal conduction model was developed, based on a mixed series and parallel thermal resistor circuit, giving a skeletal thermal conductivity value of approximately 1.25 W·m-1·K-1, which matches the value of the ordinary AAO membranes prepared from the same acid solution. The effect of different filler materials as well as the variation of the number of transversal nanochannels and the length of the 3D-AAO membrane in the effective thermal conductivity of the composite was studied. Finally, the thermal conductivity of two 3D-AAO membranes filled with cobalt and bismuth telluride was also measured, which was in good agreement with the thermal model predictions. Therefore, this work proved this structure as a powerful approach to tailor thermal properties.

  6. Tailoring thermal conductivity via three-dimensional porous alumina.

    Science.gov (United States)

    Abad, Begoña; Maiz, Jon; Ruiz-Clavijo, Alejandra; Caballero-Calero, Olga; Martin-Gonzalez, Marisol

    2016-12-09

    Three-dimensional anodic alumina templates (3D-AAO) are an astonishing framework with open highly ordered three-dimensional skeleton structures. Since these templates are architecturally different from conventional solids or porous templates, they teem with opportunities for engineering thermal properties. By establishing the mechanisms of heat transfer in these frameworks, we aim to create materials with tailored thermal properties. The effective thermal conductivity of an empty 3D-AAO membrane was measured. As the effective medium theory was not valid to extract the skeletal thermal conductivity of 3D-AAO, a simple 3D thermal conduction model was developed, based on a mixed series and parallel thermal resistor circuit, giving a skeletal thermal conductivity value of approximately 1.25 W·m(-1)·K(-1), which matches the value of the ordinary AAO membranes prepared from the same acid solution. The effect of different filler materials as well as the variation of the number of transversal nanochannels and the length of the 3D-AAO membrane in the effective thermal conductivity of the composite was studied. Finally, the thermal conductivity of two 3D-AAO membranes filled with cobalt and bismuth telluride was also measured, which was in good agreement with the thermal model predictions. Therefore, this work proved this structure as a powerful approach to tailor thermal properties.

  7. Anisotropic thermal conductivity of thin polycrystalline oxide samples

    Directory of Open Access Journals (Sweden)

    A. Tiwari

    2013-11-01

    Full Text Available This paper reports about the development of a modified laser-flash technique and relation to measure the in-plane thermal diffusivity of thin polycrystalline oxide samples. Thermal conductivity is then calculated with the product of diffusivity, specific heat and density. Design and operating features for evaluating in-plane thermal conductivities are described. The technique is advantageous as thin samples are not glued together to measure in-plane thermal conductivities like earlier methods reported in literature. The approach was employed to study anisotropic thermal conductivity in alumina sheet, textured kaolin ceramics and montmorillonite. Since it is rare to find in-plane thermal conductivity values for such anisotropic thin samples in literature, this technique offers a useful variant to existing techniques.

  8. Anisotropic thermal conductivity of thin polycrystalline oxide samples

    Energy Technology Data Exchange (ETDEWEB)

    Tiwari, A., E-mail: abhishektiwariiitr@gmail.com [Groupe d’Etudes des Matériaux Hétérogènes (GEMH, EA 3178), Ecole Nationale Supérieure de Céramique Industrielle, 12, Rue Atlantis, 87068 Limoges Cedex (France); Department of Mechanical and Aerospace Engineering, Monash University, Melbourne, VIC 3800 (Australia); Boussois, K.; Nait-Ali, B.; Smith, D. S.; Blanchart, P. [Groupe d’Etudes des Matériaux Hétérogènes (GEMH, EA 3178), Ecole Nationale Supérieure de Céramique Industrielle, 12, Rue Atlantis, 87068 Limoges Cedex (France)

    2013-11-15

    This paper reports about the development of a modified laser-flash technique and relation to measure the in-plane thermal diffusivity of thin polycrystalline oxide samples. Thermal conductivity is then calculated with the product of diffusivity, specific heat and density. Design and operating features for evaluating in-plane thermal conductivities are described. The technique is advantageous as thin samples are not glued together to measure in-plane thermal conductivities like earlier methods reported in literature. The approach was employed to study anisotropic thermal conductivity in alumina sheet, textured kaolin ceramics and montmorillonite. Since it is rare to find in-plane thermal conductivity values for such anisotropic thin samples in literature, this technique offers a useful variant to existing techniques.

  9. Thermal conductivity of disordered two-dimensional binary alloys.

    Science.gov (United States)

    Zhou, Yang; Guo, Zhi-Xin; Cao, Hai-Yuan; Chen, Shi-You; Xiang, Hong-Jun; Gong, Xin-Gao

    2016-10-20

    Using non-equilibrium molecular dynamics simulations, we have studied the effect of disorder on the thermal conductivity of two-dimensional (2D) C1-xNx alloys. We find that the thermal conductivity not only depends on the substitution concentration of nitrogen, but also strongly depends on the disorder distribution. A general linear relationship is revealed between the thermal conductivity and the participation ratio of phonons in 2D alloys. Localization mode analysis further indicates that the thermal conductivity variation in the ordered alloys can be attributed to the number of inequivalent atoms. As for the disordered alloys, we find that the thermal conductivity variation can be described by a simple linear formula with the disorder degree and the substitution concentration. The present study suggests some general guidance for phonon manipulation and thermal engineering in low dimensional alloys.

  10. A study on the thermal conductivity of compacted bentonites

    CERN Document Server

    Tang, Anh-Minh; Le, Trung Tinh; 10.1016/j.clay.2007.11.001

    2008-01-01

    Thermal conductivity of compacted bentonite is one of the most important properties in the design of high-level radioactive waste repositories where this material is proposed for use as a buffer. In the work described here, a thermal probe based on the hot wire method was used to measure the thermal conductivity of compacted bentonite specimens. The experimental results were analyzed to observe the effects of various factors (i.e. dry density, water content, hysteresis, degree of saturation and volumetric fraction of soil constituents) on the thermal conductivity. A linear correlation was proposed to predict the thermal conductivity of compacted bentonite based on experimentally observed relationship between the volumetric fraction of air and the thermal conductivity. The relevance of this correlation was finally analyzed together with others existing methods using experimental data on several compacted bentonites.

  11. Nanofluids Thermal Conductivity Measurement in a Bénard Cell

    Directory of Open Access Journals (Sweden)

    Mohamed Mojahed

    2013-01-01

    Full Text Available Thermal conductivity measurements of nanofluids were the subject of a considerable amount of published research works. Up to now, the experimental results reported in the current literature are still scarce and show many discrepancies. In this paper we propose measurements of this parameter using another experimental set-up. Because of very good thermal controls and big aspect ratio, the Bénard set-up is particularly well suited to determine the thermal conductivity. The aim of this paper is to detail the experimental measurement protocol. The investigated liquid is composed of single walled carbon nanotubes dispersed in water. The effect of liquid temperature on thermal conductivity was investigated. Obtained results confirm the potential of nanofluids in enhancing thermal conductivity and also show that the thermal conductivity temperature dependence is nonlinear, which is different from the results for metal/metal oxide nanofluids.

  12. Thermal conductance of pressed contacts at liquid helium temperatures

    Science.gov (United States)

    Salerno, L. J.; Kittel, P.; Spivak, A. L.

    1983-01-01

    It is pointed out that the optimum design of cryogenic instruments requires accurate thermal models. The present models are limited by a lack of knowledge of the low temperature thermal conductance of the bolted joints which are typically used in the instrument-to-system interface. In connection with studies of pressed contacts, it has been found that the thermal conductance does not obey the Wiedemann-Franz law. The present investigation is concerned with the characterization of the thermal conductance of pressed contacts at liquid helium-4 temperatures, taking into account the dependence of thermal contact conductance on applied force and temperature. It is shown that for the 0.4 micron OFHC copper pressed contact pair, the thermal conductance varies roughly as the second power of the temperature, and increases with increasing applied force.

  13. Thermal Conduction and Insulation Modification in Asphalt-Based Composites

    Institute of Scientific and Technical Information of China (English)

    Xiaofeng Zhou; Shengyue Wang; Chao Zhou

    2012-01-01

    The relationship between thermal conductivity and properties of mixing particles is required for quantitative study of heat transfer processes in asphalt-based materials. In this paper, we measured the e?ective ther- mal conductivity of asphalt-based materials with thermal conduction (graphite) and insulation (cenosphere) powders modification. By taking account of the particle shape, volume fraction, the thermal conductivity of filling particles and base asphalt, we present a new differential effective medium formula to predict the thermal conductivity modification in asphalt-based composite. Our theoretical predications are in good agreement with the experiment data. The new model can be applied for predicting the thermal properties of asphalt-based mixture, which is available for most of thermal modification in two-phase composites.

  14. Retention of radium from thermal waters on sand filters and adsorbents

    Energy Technology Data Exchange (ETDEWEB)

    Elejalde, C. [Dpto. de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria, Alameda de Urquijo s/n, 48013 Bilbao (Spain)]. E-mail: inpelsac@bi.ehu.es; Herranz, M. [Dpto. de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria, Alameda de Urquijo s/n, 48013 Bilbao (Spain); Idoeta, R. [Dpto. de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria, Alameda de Urquijo s/n, 48013 Bilbao (Spain); Legarda, F. [Dpto. de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria, Alameda de Urquijo s/n, 48013 Bilbao (Spain); Romero, F. [Dpto. de Ingenieria Quimica y del Medio Ambiente, Escuela Tecnica Superior de Ingenieria, Alameda de Urquijo s/n, 48013 Bilbao (Spain); Baeza, A. [Dpto. de Fisica, Facultad de Veterinaria, Universidad de Extremadura, Avda. Universidad s/n, 10071 Caceres (Spain)

    2007-06-18

    This study was focussed on laboratory experiences of retention of radium from one thermal water on sand filters and adsorbents, trying to find an easy method for the elimination in drinkable waters polluted with this natural radio-nuclide. A thermal water from Cantabria (Spain) was selected for this work. Retention experiences were made with columns of 35 mm of diameter containing 15 cm layers of washed river sand or 4 cm layers of zeolite A3, passing known volumes of thermal water at flows between 4 and 40 ml/min with control of the retained radium by determining the amount in the water after the treatment. The statistical analysis of data suggests that retention depends on the flow and the volume passed through the columns. As additional adsorbents were used kaolin and a clay rich in illite. Jar-test experiences were made agitating known weights of adsorbents with the selected thermal water, with addition of flocculants and determination of radium in filtrated water after the treatment. Data suggest that retention is related to the weight of adsorbent used, but important quantities of radium seem remain in solution for higher amounts of adsorbents, according to the statistical treatment of data. The elution of retained radium from columns or adsorbents, previously used in experiences, should be the aim of a future research.

  15. Transport of heavy metals and chemical compatibility of hydraulic conductivity of a compacted sand-bentonite mixture

    Directory of Open Access Journals (Sweden)

    Nanthanit Charoenthaisong

    2008-03-01

    Full Text Available Clayey soils are usually used as barrier material in landfill liners because of its low hydraulic conductivity and high sorption capacity. Bentonite, which consists mainly of montmorillonite, has a high cation exchange capacity resulting in a high retention capacity of heavy metals. Sand is a permeable material but its hydraulic conductivity decreases significantly when mixed with bentonite. However, using a sand-bentonite mixture as landfill liners is questionable, because the hydraulic conductivity of the sand-bentonite mixture may increase when permeated with heavy metal solutions, which are normally found in landfill leachates. In this paper, transport of heavy metals through a compacted sand-bentonite mixture and its chemical compatibility were studied through the batch adsorption test, the column test, and the hydraulic conductivity test.Experimental results indicate that the sorption capacity of the bentonite, ranked in descending order, was Cr3+, Pb2+, Cd2+, Zn2+, and Ni2+, respectively. The diffusion coefficients of the sand-bentonite mixture were in the order of 10-5 cm2/s and the retardation factors were 130, 115, 111, and 90 for Pb2+, Ni2+, Zn2+, and Cd2+, respectively. The hydraulic conductivity of thesand-bentonite mixture was only compatible with a chromium solution having a concentration not greater than 0.001 M.

  16. Measuring thermal conductivity of thin films by Scanning Thermal Microscopy combined with thermal spreading resistance analysis.

    Science.gov (United States)

    Juszczyk, J; Kaźmierczak-Bałata, A; Firek, P; Bodzenta, J

    2017-01-27

    While measuring the thermal properties of a thin film, one of the most often encountered problems is the influence of the substrate thermal properties on measured signal and the need for its separation. In this work an approach for determining the thermal conductivity κ of a thin layer is presented. It bases on Scanning Thermal Microscopy (SThM) measurement combined with thermal spreading resistance analysis for a system consisting of a single layer on a substrate. Presented approach allows to take into account the influence of the substrate thermal properties on SThM signal and to estimate the true value of a thin film κ. It is based on analytical solution of the problem being a function of dimensionless parameters and requires numerical solution of relatively simple integral equation. As the analysis utilizes a solution in dimensionless parameters it can be used for any substrate-layer system. As an example, the method was applied for determination of the thermal conductivities of 4 different thin layers of thicknesses from 12 to 100nm. The impact of model parameters on the uncertainty of the estimated final κ value was analyzed.

  17. Tunable thermal conductivity in mesoporous silicon by slight porosity change

    Science.gov (United States)

    Seol, Jae Hun; Barth, David S.; Zhu, Jia; Ćoso, Dušan; Hippalgaonkar, Kedar; Lim, Jongwoo; Han, Junkyu; Zhang, Xiang; Majumdar, Arun

    2017-08-01

    We report the thermal conductivity of photoelectrochemically synthesized mesoporous silicon (MPS), with ˜20-nm diameter pores and 52%-58% porosity. The thermal conductivity of MPS samples with a thickness of a few microns was measured using the three omega (3 ω ) differential technique. We experimentally demonstrated that the thermal conductivity of MPS varies between 3 and 7 W/m K at room temperature and is dependent on the photoelectrochemical etching times used during the MPS synthesis, which induces a slight change in the MPS porosity. Calculations were conducted using the Boltzmann transport equation in the relaxation time approximation, with the results suggesting that the large thermal conductivity reduction in the MPSs was not entirely explained by the pore boundary scattering. Our findings indicate that elastic softening in the mesoporous structure may be responsible for the reduction in the thermal conductivity.

  18. Measurement of the anisotropic thermal conductivity of the porcine cornea.

    Science.gov (United States)

    Barton, Michael D; Trembly, B Stuart

    2013-10-01

    Accurate thermal models for the cornea of the eye support the development of thermal techniques for reshaping the cornea and other scientific purposes. Heat transfer in the cornea must be quantified accurately so that a thermal treatment does not destroy the endothelial layer, which cannot regenerate, and yet is responsible for maintaining corneal transparency. We developed a custom apparatus to measure the thermal conductivity of ex vivo porcine corneas perpendicular to the surface and applied a commercial apparatus to measure thermal conductivity parallel to the surface. We found that corneal thermal conductivity is 14% anisotropic at the normal state of corneal hydration. Small numbers of ex vivo feline and human corneas had a thermal conductivity perpendicular to the surface that was indistinguishable from the porcine corneas. Aqueous humor from ex vivo porcine, feline, and human eyes had a thermal conductivity nearly equal to that of water. Including the anisotropy of corneal thermal conductivity will improve the predictive power of thermal models of the eye. Copyright © 2013 Elsevier Ltd. All rights reserved.

  19. 3 omega method for specific heat and thermal conductivity measurements

    CERN Document Server

    Lü, L; Zhang, D L

    2001-01-01

    We present a 3 omega method for simultaneously measuring the specific heat and thermal conductivity of a rod- or filament-like specimen using a way similar to a four-probe resistance measurement. The specimen in this method needs to be electrically conductive and with a temperature-dependent resistance, for acting both as a heater to create a temperature fluctuation and as a sensor to measure its thermal response. With this method we have successfully measured the specific heat and thermal conductivity of platinum wire specimens at cryogenic temperatures, and measured those thermal quantities of tiny carbon nanotube bundles some of which are only 10^-9 g in mass.

  20. Polyaniline Conducting Electroactive Polymers Thermal and Environmental Stability Studies

    Directory of Open Access Journals (Sweden)

    Reza Ansari

    2006-01-01

    Full Text Available In the current studies, polyaniline (PANi was prepared both chemical and electrochemically in the presence of different bronsted acids from aqueous solutions. The effect of thermal treatment on electrical conductivity, and thermal stability of the PANi conducting polymers were investigated using 4-point probe and TGA techniques respectively. It was found that polymer prepared by CV method is more thermally stable than those prepared by the other electrochemical techniques. In this paper we have also reviewed some fundamental information about synthesis, general properties, diverse applications, thermal and environmental stability of polyaniline conducting polymers.

  1. Lattice thermal conductivity in layered BiCuSeO

    KAUST Repository

    Kumar, S.

    2016-06-30

    We quantify the low lattice thermal conductivity in layered BiCuSeO (the oxide with the highest known figure of merit). It turns out that the scattering of acoustical into optical phonons is strongly enhanced in the material because of the special structure of the phonon dispersion. For example, at room temperature the optical phonons account for an enormous 42% of the lattice thermal conductivity. We also quantify the anisotropy of the lattice thermal conductivity and determine the distribution of the mean free path of the phonons at different temperatures to provide a guide for tuning the thermal properties. © the Owner Societies 2016.

  2. Thermal conductivity of reinforced soils:A literature review

    Institute of Scientific and Technical Information of China (English)

    Muge Elif Orakoglu; JianKun Liu

    2014-01-01

    This-paper-aims-a-review-of-the-literature-related-to-soil-reinforcements-to-achieve-lower-soil-thermal-conductivity-(λ).-The-use-of-various-natural-and-synthetic-fibers,-polymers,-geosynthetics,-agricultural-waste/materials,-and-nanoclays-is-dis-cussed-and-existing-prediction-models-that-have-been-thought-to-affect-low-thermal-conductivity-are-presented.

  3. Model for predicting thermal conductivity using transient hot wire method

    Science.gov (United States)

    Kumar, Sublania Harish; Singh K., J.; Somani A., K.

    2016-05-01

    The use of the hot wire method for estimating the thermal conductivity measurement has recently known a significant increase. However, this method is theoretically not applicable to materials. Thermal conductivity values are necessary whenever a heat transfer problem is to be evaluated.

  4. Development of high-thermal-conductivity silicon nitride ceramics

    Directory of Open Access Journals (Sweden)

    You Zhou

    2015-09-01

    Full Text Available Silicon nitride (Si3N4 with high thermal conductivity has emerged as one of the most promising substrate materials for the next-generation power devices. This paper gives an overview on recent developments in preparing high-thermal-conductivity Si3N4 by a sintering of reaction-bonded silicon nitride (SRBSN method. Due to the reduction of lattice oxygen content, the SRBSN ceramics could attain substantially higher thermal conductivities than the Si3N4 ceramics prepared by the conventional gas-pressure sintering of silicon nitride (SSN method. Thermal conductivity could further be improved through increasing the β/α phase ratio during nitridation and enhancing grain growth during post-sintering. Studies on fracture resistance behaviors of the SRBSN ceramics revealed that they possessed high fracture toughness and exhibited obvious R-curve behaviors. Using the SRBSN method, a Si3N4 with a record-high thermal conductivity of 177 Wm−1K−1 and a fracture toughness of 11.2 MPa m1/2 was developed. Studies on the influences of two typical metallic impurity elements, Fe and Al, on thermal conductivities of the SRBSN ceramics revealed that the tolerable content limits for the two impurities were different. While 1 wt% of impurity Fe hardly degraded thermal conductivity, only 0.01 wt% of Al caused large decrease in thermal conductivity.

  5. Thermal conductivity of cementitious grouts for geothermal heat pumps. Progress report FY 1997

    Energy Technology Data Exchange (ETDEWEB)

    Allan, M.L.

    1997-11-01

    Grout is used to seal the annulus between the borehole and heat exchanger loops in vertical geothermal (ground coupled, ground source, GeoExchange) heat pump systems. The grout provides a heat transfer medium between the heat exchanger and surrounding formation, controls groundwater movement and prevents contamination of water supply. Enhanced heat pump coefficient of performance (COP) and reduced up-front loop installation costs can be achieved through optimization of the grout thermal conductivity. The objective of the work reported was to characterize thermal conductivity and other pertinent properties of conventional and filled cementitious grouts. Cost analysis and calculations of the reduction in heat exchanger length that could be achieved with such grouts were performed by the University of Alabama. Two strategies to enhance the thermal conductivity of cementitious grouts were used simultaneously. The first of these was to incorporate high thermal conductivity filler in the grout formulations. Based on previous tests (Allan and Kavanaugh, in preparation), silica sand was selected as a suitable filler. The second strategy was to reduce the water content of the grout mix. By lowering the water/cement ratio, the porosity of the hardened grout is decreased. This results in higher thermal conductivity. Lowering the water/cement ratio also improves such properties as permeability, strength, and durability. The addition of a liquid superplasticizer (high range water reducer) to the grout mixes enabled reduction of water/cement ratio while retaining pumpability. Superplasticizers are commonly used in the concrete and grouting industry to improve rheological properties.

  6. Complex conductivity response to silver nanoparticles in partially saturated sand columns

    Science.gov (United States)

    Abdel Aal, Gamal; Atekwana, Estella A.; Werkema, D. Dale

    2017-02-01

    The increase in the use of nanoscale materials in consumer products has resulted in a growing concern of their potential hazard to ecosystems and public health from their accidental or intentional introduction to the environment. Key environmental, health, and safety research needs include knowledge and methods for their detection, characterization, fate, and transport. Specifically, techniques available for the direct detection and quantification of their fate and transport in the environment are limited. Their small size, high surface area to volume ratio, interfacial, and electrical properties make metallic nanoparticles, such as silver nanoparticles, good targets for detection using electrical geophysical techniques. Here we measured the complex conductivity response to silver nanoparticles in sand columns under varying moisture conditions (0-30%), nanoparticle concentrations (0-10 mg/g), lithology (presence of clay), pore water salinity (0.0275 and 0.1000 S/m), and particle size (35, 90-210 and 1500-2500 nm). Based on the Cole-Cole relaxation models we obtained the chargeability and the time constant. We demonstrate that complex conductivity can detect silver nanoparticles in porous media with the response enhanced by higher concentrations of silver nanoparticles, moisture content, ionic strength, clay content and particle diameter. Quantification of the volumetric silver nanoparticles content in the porous media can also be obtained from complex conductivity parameters based on the strong power law relationships.

  7. Thermal conductivities of minor actinide oxides for advanced fuel

    Energy Technology Data Exchange (ETDEWEB)

    Tsuyoshi Nishi; Akinori Itoh; Masahide Takano; Mitsuo Akabori; Yasuo Arai; Kazuo Minato [Nuclear Science and Engineering Directorate, Japan Atomic Energy Agency, Tokai-mura, Ibaraki 319-1195 (Japan)

    2008-07-01

    The thermal diffusivities of americium oxide and neptunium dioxide were determined by a laser flash method. It was found that the thermal diffusivities of AmO{sub 2-x} and NpO{sub 2} decreased with increasing temperature. It was also found that the decrease in O/Am ratio during the thermal diffusivity measurements under vacuum resulted in a slight decrease in thermal diffusivity of AmO{sub 2-x}. The thermal conductivities of AmO{sub 2-x} and NpO{sub 2} were evaluated from the measured thermal diffusivities, heat capacities and bulk densities. The thermal conductivity of AmO{sub 2-x} was smaller than those of the literature values of UO{sub 2} and PuO{sub 2}. On the other hand, the thermal conductivity of NpO{sub 2} from 873 to 1473 K lay between those of UO{sub 2} and PuO{sub 2}. The thermal conductivities of AmO{sub 2-x} and NpO{sub 2} decreased with increasing temperature in the temperature range investigated. This temperature dependence of thermal conductivities showed a similar tendency as those of UO{sub 2}, PuO{sub 2} and (U{sub 0.8}Pu{sub 0.2})O{sub 2-x}. (authors)

  8. Therma1 Conductivity and Durability of Advanced Thermal Barrier Coatings

    Science.gov (United States)

    Zhu, Dong-Ming; Miller, Robert A.

    2003-01-01

    Thermal barrier coatings (TBCs) will play a crucial role in advanced gas turbine engines because of their ability to further increase engine operating temperature and reduce cooling, thus helping to achieve engine emission and efficiency goals. Future TBCs must be designed with increased phase stability, lower thermal conductivity, and improved sintering and thermal stress resistance in order to effectively protect engine hot-section components. Advanced low conductivity TBCs are being developed at NASA by incorporating multi-component oxide dopants into zirconia-yttria or hafnia-yttria to promote the formation of thermodynamically stable defect clusters within the coating structures. This presentation will primarily focus on thermal conductivity and durability of the novel defect cluster thermal barrier coatings for turbine airfoil and combustor applications, determined by a unique CO2 laser heat-flux approach. The laser heat-flux testing approach emphasizes the real-time monitoring and assessment of the coating thermal conductivity under simulated engine temperature and thermal gradient conditions. The conductivity increase due to coating sintering (and/or phase change) and the conductivity decrease due to coating delamination have been determined under steady-state, cyclic, uniform or non-uniform heat-flux conditions. The coating radiation flux resistance has been evaluated by varying coating thermal gradients, and also by using a laser-heated radiative-flux source. Advanced multi-component TBC systems have been shown to have significantly reduced thermal conductivity and improved high temperature stability due to the nano-sized, low mobility defect clusters associated with the paired rare earth dopant additions. The effect of oxide defect cluster dopants on coating thermal conductivity, thermal stability and furnace cyclic durability will also be discussed. The current low conductivity TBC systems have demonstrated long-term cyclic durability at very high

  9. Thermal Conductivity of Alumina-reinforced Zirconia Composites

    Science.gov (United States)

    Bansal, Narottam P.

    2005-01-01

    10-mol% yttria-stabilized zirconia (10SZ) - alumina composites containing 0-30 mol% alumina were fabricated by hot pressing at 1500 C in vacuum. Thermal conductivity was determined at various temperatures using a steady-state laser heat flux technique. Thermal conductivity of the composites increased with increase in alumina content. Composites containing 0, 5, and 10-mol% alumina did not show any change in thermal conductivity with temperature. However, those containing 20 and 30-mol% alumina showed a decrease in thermal conductivity with increase in temperature. The measured values of thermal conductivity were in good agreement with those calculated from the Maxwell-Eucken model where one phase is uniformly dispersed within a second major continuous phase.

  10. Thermal conductivity modeling of water containing metal oxide nanoparticles

    Institute of Scientific and Technical Information of China (English)

    Ahmad Azari

    2015-01-01

    The nano particles have demonstrated great potential to improve the heat transfer characteristics of heat transfer fluids. Possible parameters responsible for this increase were studied. The heat transfer profile in the nanolayer region was combined with other parameters such as volume fraction, particle radius thermal conductivity of the fluid, particle and nanolayer, to formulate a thermal conductivity model. Results predicting the thermal conductivity of nanofluids using the model were compared with experimental results as well as studies by other researchers. The comparison of the results obtained for the CuO/water and TiO2/water nanofluids studied shows that the correlation proposed is in closest proximity in predicting the experimental results for the thermal conductivity of a nanofluid. Also, a parametric study was performed to understand how a number of factors affect the thermal conductivity of nanofluids using the developed correlation.

  11. Thermal conductivity of silicon nanowires embedded on thermoelectric platforms

    Science.gov (United States)

    Choi, JinYong; Cho, Kyoungah; Yoon, Dae Sung; Kim, Sangsig

    2016-10-01

    In this study, we propose a simple method for obtaining the thermal conductivity of silicon nanowires (SiNWs) embedded on a thermoelectric platform. The approximation of the heat flux in SiNWs with temperature differences enables the determination of thermal conductivity. Using this method, the thermal conductivities of our n- and p-type SiNWs are found to be 18.06  ±  0.12 and 20.29  ±  0.77 W m-1 · K-1, respectively. The atomic weight of arsenic ions in the n-type SiNWs is responsible for a lower thermal conductivity than that of boron ions in the p-type SiNWs. Our results demonstrate that this simple method is capable of measuring the thermal conductivity of thermoelectric nanomaterials embedded on thermoelectric devices.

  12. Thermal Conductivity of Ce Doped Bi-2212 Superconductors

    Institute of Scientific and Technical Information of China (English)

    LI Bo; WU Bai-Mei; M.Ausloos

    2004-01-01

    The temperature dependence of the thermal conductivity in Bi2Sr2 Ca1-x Cex Cu2Oy x = 0.1, 0.2, 0.3, 0.4 is presented. With increasing Ce-doping level, the thermal conductivity peak under TC is suppressed then disappears,while another peak appears at low temperatures for the non-superconducting compounds. The numerical analysis shows that the thermal conductivity peak under TC can be well described by the normal electron relaxation-time contribution model, and the phonon-induced thermal conductivity peak could be well described within the Debye approximation of the phonon spectrum. The existence and variation of these two thermal conductivity peaks indicate the adjustability between the superconducting and insulating components in the samples with different Ce-doping levels.

  13. Thermal conductance of graphene/hexagonal boron nitride heterostructures

    Science.gov (United States)

    Lu, Simon; McGaughey, Alan J. H.

    2017-03-01

    The lattice-based scattering boundary method is applied to compute the phonon mode-resolved transmission coefficients and thermal conductances of in-plane heterostructures built from graphene and hexagonal boron nitride (hBN). The thermal conductance of all structures is dominated by acoustic phonon modes near the Brillouin zone center that have high group velocity, population, and transmission coefficient. Out-of-plane modes make their most significant contributions at low frequencies, whereas in-plane modes contribute across the frequency spectrum. Finite-length superlattice junctions between graphene and hBN leads have a lower thermal conductance than comparable junctions between two graphene leads due to lack of transmission in the hBN phonon bandgap. The thermal conductances of bilayer systems differ by less than 10% from their single-layer counterparts on a per area basis, in contrast to the strong thermal conductivity reduction when moving from single- to multi-layer graphene.

  14. Manipulating Steady Heat Conduction by Sensu-shaped Thermal Metamaterials

    CERN Document Server

    Han, Tiancheng; Liu, Dan; Gao, Dongliang; Li, Baowen; Thong, John T L; Qiu, Cheng-Wei

    2014-01-01

    The ability to design the control of heat flow has innumerable benefits in the design of electronic systems such as thermoelectric energy harvesters, solid-state lighting, and thermal imagers, where the thermal design plays a key role in performance and device reliability. However, to realize one advanced control function of thermal flux, one needs to design one sophisticated, multilayered and inhomogeneous thermal structure with different composition/shape at different regions of one device. In this work, we employ one identical sensu-unit with facile natural composition to experimentally realize a new class of thermal metamaterials for controlling thermal conduction (e.g., thermal concentrator, focusing/resolving, uniform heating), only resorting to positioning and locating the same unit element of sensu-shape structure. The thermal metamaterial unit and the proper arrangement of multiple identical units are capable of transferring, redistributing and managing thermal energy in a versatile fashion. It is al...

  15. Low thermal conductivity of graphyne nanotubes from molecular dynamics study

    Science.gov (United States)

    Hu, Ming; Jing, Yuhang; Zhang, Xiaoliang

    2015-04-01

    It is well known that carbon nanotubes (CNTs) possess ultrahigh thermal conductivity that is comparable to bulk diamond. However, no research has studied the possible low thermal conductivity of different CNTs so far. By performing nonequilibrium molecular dynamic simulations, we reveal that the perfect graphyne nanotube (GNT) exhibits an unprecedentedly low thermal conductivity (below 10 W/mK at room temperature), which is generally two orders of magnitude lower than that of ordinary CNTs and even lower than the values reported for defected, doped, and chemically functionalized CNTs. By performing phonon polarization and spectral energy density analysis, we observe that the ultralow thermal conductivity stems from the unique atomic structure of the GNT, consisting of the weak acetylenic linkage (s p C-C bonds) and the strong hexagonal ring (s p2 C-C bonds), which results in a large vibrational mismatch between these two components, and thus induces significantly inefficient heat transfer. Moreover, the thermal transport in GNT with a large number of acetylenic linkages is dominated by the low frequency longitudinal modes in the linkage. Such strong confinement of the low frequency thermal energy results in the extremely low thermal conductivity due to the flattened phonon dispersion curves (low phonon group velocities). The exploration of the abnormal thermal transport of GNTs paves the way for design and application of the relevant devices that could benefit from the ultralow thermal conductivity, such as thermoelectrics for energy conversion.

  16. Anisotropic Thermal Conduction in Polymers and its Molecular Origins

    Science.gov (United States)

    Nieto Simavilla, David; Venerus, David; Schieber, Jay; uCoSm Team

    2014-03-01

    Anisotropy in thermal conductivity has a significant impact on both processing and final properties of materials. Simple molecular arguments suggest that Fourier?s law must be generalized to allow for anisotropic thermal conductivity. We present two complementary experimental methods to obtain quantitative measurements of the thermal diffusivity (conductivity) tensor. We report anisotropic thermal diffusivity and stress in molten, cross-linked and solid polymers under several types of flows. Our results support the validity of a linear relationship between stress and anisotropy in thermal conductivity. When the proportionality constant, the stress-thermal coefficient, is made dimensionless by the plateau modulus of the polymer melt, a universal value of approximately 0.03 is observed for all chemistries. Such a universality is surprising, since phonon transport mechanisms are sensitive to chemical structure. For instance, the analogous stress-optic coefficient depends strongly on chemistry, and can even change sign. Connecting these measurements with current theories for thermal transport in amorphous materials, such as Minimum Thermal Conductivity (MTC) model, is crucial to understand the molecular origins of anisotropic thermal conduction in polymers.

  17. Investigations Regarding the Thermal Conductivity of Straw

    OpenAIRE

    2010-01-01

    The reduction of buildings heat losses and pollutants emissions is a worldwide priority. It’s intending to reduce the specific final energy consumption under limit of 120...150 kWh/m2.yr and even under 15...45 kWh/m2.yr, foreseen in 2020 for the passive houses, which is necessary for a sustainable development and for allowing to became profitable the use of unconventional energies [1]. These values can be achieved through the use of thermal insulations, for protecting the constructions fund a...

  18. Nanostructure-thermal conductivity relationships in protic ionic liquids.

    Science.gov (United States)

    Murphy, Thomas; Varela, Luis M; Webber, Grant B; Warr, Gregory G; Atkin, Rob

    2014-10-16

    The thermal conductivities of nine protic ionic liquids (ILs) have been investigated between 293 and 340 K. Within this range, the thermal conductivities are between 0.18 and 0.30 W · m(-1) · K(-1). These values are higher than those typically associated with oils and aprotic ILs, but lower than those of strongly hydrogen bonding solvents like water. Weak linear decreases in thermal conductivity with temperature are noted, with the exception of ethanolammonium nitrate (EtAN) where the thermal conductivity increases with temperature. The dependence of thermal conductivity on IL type is analyzed with use of the Bahe-Varela pseudolattice theory. This theory treats the bulk IL as an array of ordered domains with intervening domains of uncorrelated structure which enable and provide barriers to heat propagation (respectively) via allowed vibrational modes. For the protic ILs investigated, thermal conductivity depends strongly on the IL cation alkyl chain length. This is because the cation alkyl chain controls the dimensions of the IL bulk nanostructure, which consists of charged (ordered domains) and uncharged regions (disordered domains). As the cation alkyl chain controls the dimensions of the disordered domains, it thus limits the thermal conductivity. To test the generality of this interpretation, the thermal conductivities of propylammonium nitrate (PAN) and PAN-octanol mixtures were examined; water selectively swells the PAN charged domain, while octanol swells the uncharged regions. Up to a certain concentration, adding water increases thermal conduction and octanol decreases it, as expected. However, at high solute concentrations the IL nanostructure is broken. When additional solvent is added above this concentration the rate of change in thermal conductivity is greatly reduced. This is because, in the absence of nanostructure, the added solvent only serves to dilute the salt solution.

  19. Analysis of thermal conductivity in tree-like branched networks

    Institute of Scientific and Technical Information of China (English)

    Kou Jian-Long; Lu Hang-Jun; Wu Feng-Min; Xu You-Sheng

    2009-01-01

    Asymmetric tree-like branched networks are explored by geometric algorithms.Based on the network,an analysis of the thermal conductivity is presented.The relationship between effective thermal conductivity and geometric structures is obtained by using the thermal-electrical analogy technique.In all studied cases,a clear behaviour is observed,where angle(δ,θ)among parent branching extended lines,branches and parameter of the geometric structures have stronger effects on the effective thermal conductivity.When the angle δ is fixed,the optical diameter ratio β* is dependent on angle θ.Moreover,γ and m are not related to β*.The longer the branch is,the smaller the effective thermal conductivity will be.It is also found that when the angle θ<δ/2,the higher the iteration m is,the lower the thermal conductivity will be and it tends to zero,otherwise,it is bigger than zero.When the diameter ratio β1<0.707 and angle δ is bigger,the optimal k of the perfect ratio increases with the increase of the angle δ;when β1>0.707,the optimal k decreases.In addition,the effective thermal conductivity is always less than that of single channel material.The present results also show that the effective thermal conductivity of the asymmetric tree-like branched networks does not obey Murray's law.

  20. Method for estimating the lattice thermal conductivity of metallic alloys

    Energy Technology Data Exchange (ETDEWEB)

    Yarbrough, D.W.; Williams, R.K.

    1978-08-01

    A method is described for calculating the lattice thermal conductivity of alloys as a function of temperature and composition for temperatures above theta/sub D//2 using readily available information about the atomic species present in the alloy. The calculation takes into account phonon interactions with point defects, electrons and other phonons. Comparisons between experimental thermal conductivities (resistivities) and calculated values are discussed for binary alloys of semiconductors, alkali halides and metals. A discussion of the theoretical background is followed by sufficient numerical work to facilitate the calculation of lattice thermal conductivity of an alloy for which no conductivity data exist.

  1. The influence of topology on hydraulic conductivity in a sand-and-gravel aquifer

    Science.gov (United States)

    Morin, R.H.; LeBlanc, D.R.; Troutman, B.M.

    2010-01-01

    A field experiment consisting of geophysical logging and tracer testing was conducted in a single well that penetrated a sand-and-gravel aquifer at the U.S. Geological Survey Toxic Substances Hydrology research site on Cape Cod, Massachusetts. Geophysical logs and flowmeter/pumping measurements were obtained to estimate vertical profiles of porosity ??, hydraulic conductivity K, temperature, and bulk electrical conductivity under background, freshwater conditions. Saline-tracer fluid was then injected into the well for 2 h and its radial migration into the surrounding deposits was monitored by recording an electromagnetic-induction log every 10 min. The field data are analyzed and interpreted primarily through the use of Archie's (1942) law to investigate the role of topological factors such as pore geometry and connectivity, and grain size and packing configuration in regulating fluid flow through these coarse-grained materials. The logs reveal no significant correlation between K and ??, and imply that groundwater models that link these two properties may not be useful at this site. Rather, it is the distribution and connectivity of the fluid phase as defined by formation factor F, cementation index m, and tortuosity ?? that primarily control the hydraulic conductivity. Results show that F correlates well with K, thereby indicating that induction logs provide qualitative information on the distribution of hydraulic conductivity. A comparison of ??, which incorporates porosity data, with K produces only a slightly better correlation and further emphasizes the weak influence of the bulk value of ?? on K. Copyright ?? 2009 The Author(s) are Federal Government Employees. Journal compilation ?? 2009 National Ground Water Association.

  2. Thermally Conductive Tape Based on Carbon Nanotube Arrays

    Science.gov (United States)

    Kashani, Ali

    2011-01-01

    To increase contact conductance between two mating surfaces, a conductive tape has been developed by growing dense arrays of carbon nanotubes (CNTs, graphite layers folded into cylinders) on both sides of a thermally conductive metallic foil. When the two mating surfaces are brought into contact with the conductive tape in between, the CNT arrays will adhere to the mating surface. The van der Waals force between the contacting tubes and the mating surface provides adhesion between the two mating surfaces. Even though the thermal contact conductance of a single tube-to-tube contact is small, the tremendous amount of CNTs on the surface leads to a very large overall contact conductance. Interface contact thermal resistance rises from the microroughness and the macroscopic non-planar quality of mating surfaces. When two surfaces come into contact with each other, the actual contact area may be much less than the total area of the surfaces. The real area of contact depends on the load, the surface roughness, and the elastic and inelastic properties of the surface. This issue is even more important at cryogenic temperatures, where materials become hard and brittle and vacuum is used, which prevents any gas conduction through the interstitial region. A typical approach to increase thermal contact conductance is to use thermally conducting epoxies or greases, which are not always compatible with vacuum conditions. In addition, the thermal conductivities of these compounds are often relatively low. The CNTs used in this approach can be metallic or semiconducting, depending on the folding angle and diameter. The electrical resistivity of multiwalled carbon nanotubes (MWCNTs) has been reported. MWCNTs can pass a current density and remain stable at high temperatures in air. The thermal conductivity of a MWCNT at room temperature is measured to be approximately 3,000 W/m-K, which is much larger than that of diamond. At room temperature, the thermal conductance of a 0.3 sq cm

  3. Determination of Radiative Thermal Conductivity in Needlepunched Nonwovens

    Directory of Open Access Journals (Sweden)

    Rahul Vallabh

    2008-12-01

    Full Text Available Radiation heat transfer is found to be the dominant mode of heat transfer at temperatures higher than 400-500K [11]. Convection heat transfer being negligible in nonwovens, effective thermal conductivity is given by the sum of its conduction and radiation components. In this research two methods were identified to determine radiative thermal conductivity of needlepunched samples made from Nomex fibers. The first method involved the determination of radiative thermal conductivity using effective (total thermal conductivity determined using a Guarded Hot Plate (GHP instrument. In the second method radiative thermal conductivity was estimated using the extinction coefficient of samples. The extinction coefficient was determined by using direct transmission measurements made using a Fourier Transform InfraRed (FTIR spectrometer. Results confirmed that radiation was the dominant mode of heat transfer at temperatures higher than 535 K. The conduction component of effective thermal conductivity did not change much in the range of densities tested. Empirical models for predicting the temperature difference across thickness of the fabric and the radiative thermal conductivity with R-square values of 0.94 and 0.88 respectively showed that fabric density, fabric thickness, fiber fineness, fiber length, mean pore size and applied temperature were found to have significant effect on the effective thermal conductivity and its radiation component. Though a high correlation between the results of Method 1 (Guarded Hot Plate and Method 2 (FTIR was not seen, the absorbance measurements made using the FTIR spectrometer were found to have significant effect on the radiative thermal conductivity.

  4. Thermal and tensile strength testing of thermally-conductive adhesives and carbon foam

    Science.gov (United States)

    Chertok, M.; Fu, M.; Irving, M.; Neher, C.; Shi, M.; Tolfa, K.; Tripathi, M.; Vinson, Y.; Wang, R.; Zheng, G.

    2017-01-01

    Future collider detectors, including silicon tracking detectors planned for the High Luminosity LHC, will require components and mechanical structures providing unprecedented strength-to-mass ratios, thermal conductivity, and radiation tolerance. This paper studies carbon foam used in conjunction with thermally conductive epoxy and thermally conductive tape for such applications. Thermal performance and tensile strength measurements of aluminum-carbon foam-adhesive stacks are reported, along with initial radiation damage test results.

  5. Thermal separation of soil particles from thermal conductivity measurement under various air pressures

    OpenAIRE

    Sen Lu; Tusheng Ren; Yili Lu; Ping Meng; Jinsong Zhang

    2017-01-01

    The thermal conductivity of dry soils is related closely to air pressure and the contact areas between solid particles. In this study, the thermal conductivity of two-phase soil systems was determined under reduced and increased air pressures. The thermal separation of soil particles, i.e., the characteristic dimension of the pore space (d), was then estimated based on the relationship between soil thermal conductivity and air pressure. Results showed that under both reduced and increased air...

  6. Thermal Conductivity from Core and Well log Data

    CERN Document Server

    Hartmann, Andreas; Clauser, Christoph

    2008-01-01

    The relationships between thermal conductivity and other petrophysical properties have been analysed for a borehole drilled in a Tertiary Flysch sequence. We establish equations that permit us to predict rock thermal conductivity from logging data. A regression analysis of thermal conductivity, bulk density, and sonic velocity yields thermal conductivity with an average accuracy of better than 0.2 W/(m K). As a second step, logging data is used to compute a lithological depth profile, which in turn is used to calculate a thermal conductivity profile. From a comparison of the conductivity-depth profile and the laboratory data it can be concluded that thermal conductivity can be computed with an accuracy of less than 0.3 W/(m K)from conventional wireline data. The comparison of two different models shows that this approach can be practical even if old and incomplete logging data is used. The results can be used to infer thermal conductivity for boreholes without appropriate core data that are drilled in a simil...

  7. Thermally conductive cementitious grouts for geothermal heat pumps. Progress report FY 1998

    Energy Technology Data Exchange (ETDEWEB)

    Allan, M.L.; Philippacopoulos, A.J.

    1998-11-01

    Research commenced in FY 97 to determine the suitability of superplasticized cement-sand grouts for backfilling vertical boreholes used with geothermal heat pump (GHP) systems. The overall objectives were to develop, evaluate and demonstrate cementitious grouts that could reduce the required bore length and improve the performance of GHPs. This report summarizes the accomplishments in FY 98. The developed thermally conductive grout consists of cement, water, a particular grade of silica sand, superplasticizer and a small amount of bentonite. While the primary function of the grout is to facilitate heat transfer between the U-loop and surrounding formation, it is also essential that the grout act as an effective borehole sealant. Two types of permeability (hydraulic conductivity) tests was conducted to evaluate the sealing performance of the cement-sand grout. Additional properties of the proposed grout that were investigated include bleeding, shrinkage, bond strength, freeze-thaw durability, compressive, flexural and tensile strengths, elastic modulus, Poisson`s ratio and ultrasonic pulse velocity.

  8. Thermal expansion coefficient prediction of fuel-cell seal materials from silica sand

    Science.gov (United States)

    Hidayat, Nurul; Triwikantoro, Baqiya, Malik A.; Pratapa, Suminar

    2013-09-01

    This study is focused on the prediction of coefficient of thermal expansion (CTE) of silica-sand-based fuel-cell seal materials (FcSMs) which in principle require a CTE value in the range of 9.5-12 ppm/°C. A semi-quantitative theoretical method to predict the CTE value is proposed by applying the analyzed phase compositions from XRD data and characterized density-porosity behavior. A typical silica sand was milled at 150 rpm for 1 hour followed by heating at 1000 °C for another hour. The sand and heated samples were characterized by means of XRD to perceive the phase composition correlation between them. Rietveld refinement was executed to investigate the weight fraction of the phase contained in the samples, and then converted to volume fraction for composite CTE calculations. The result was applied to predict their potential physical properties for FcSM. Porosity was taken into account in the calculation after which it was directly measured by the Archimedes method.

  9. The Influence of the Content of Furfuryl Alcohol Monomer on the Process of Moulding Sand's Thermal Destruction

    Directory of Open Access Journals (Sweden)

    Dobosz St. M.

    2014-10-01

    Full Text Available The article discusses the issue of the influence of furfuryl alcohol content in resin binders on properties of moulding sand at elevated temperature. Reducing the share of this component - due to the requirements of the European Union regarding its toxicity - may cause a decrease in temperature of moulding sands’ destruction and, consequently, the thermal deformation of moulds and the creation of many casting defects. The study examined the impact of the furfuryl alcohol content of the thermal destruction processes and on the strength of the moulding sand at an ambient temperature and the tendency to thermal deformation.

  10. New Density-based Thermal Conductivity Equation for Snow

    Directory of Open Access Journals (Sweden)

    R.K. Aggarwal

    2009-03-01

    Full Text Available More than two hundred thermal conductivity measurements for different snow densities and snow types were carried out in-situ at a field research station located in greater Himalayan range of India. These measurements were carried out using a commercially available portable thermal conductivity meter. Thermal conductivity measurements were carried out on the fresh snow, equi-temperature snow, and surface hoar and temperaturegradient snow. Average thermal conductivity of snow varied from 0.08 W/mK (Fresh snow of 120 kg/m3 density to 0.32 W/m K (Equi-temperature snow of 420 kg/m3 density. Based on these measurements, a new density-based thermal conductivity equation is proposed. Using this proposed equation, modeled snowpack temperatures showed closer agreement with the observed data as compared to the predictions based on other well-known empirical and theoretical thermal conductivity equations for snow. This study highlights the advantages and limitations of empirical based thermal conductivity equations over the complex models based on snow microstructure.Defence Science Journal, 2009, 59(2, pp.126-130, DOI:http://dx.doi.org/10.14429/dsj.59.1499

  11. Investigation of the Thermal Conductance of Selected Opal Structures

    Science.gov (United States)

    Lamberton, , Jr.; Tritt, Terry M.; Zakhidov, A.; Baughmann, R.; Khayrullin, I.

    1999-11-01

    In relation to thermoelectrics, recently some attention has come to opal structures.^1 The structure of the SiO2 opals is hoped to be useful in lowering thermal conductivity when this structure is infiltrated with traditional thermoelectric materials, such as Bi or Bi_2Te_3. Preliminary measurements show that, by infiltration, it may be possible to increase the thermoelectric figure of merit by improving the ratio of electrical conductivity to thermal conductivity.^2 We have built a new steady state thermal conductivity apparatus for measuring thermal conductivity of samples between 10K and 350K. With this new system the thermal properties of the opal systems and the effects of infiltration will be investigated. Data from the thermal conductivity and heat capacity measurements will be presented and discussed, along with a comparison of thermal conductivity obtained with the laser flash method. 1.) A. Zakhidov et al., Science , 282, 897 (1998) 2.) R. Baughman, A. Zakhidov, et.al, Proc. of ICT '98, IEEE Press, p 288 (1998)

  12. Impacts of biochar concentration and particle size on hydraulic conductivity and DOC leaching of biochar-sand mixtures

    Science.gov (United States)

    Liu, Zuolin; Dugan, Brandon; Masiello, Caroline A.; Barnes, Rebecca T.; Gallagher, Morgan E.; Gonnermann, Helge

    2016-02-01

    The amendment of soil with biochar can sequester carbon and alter hydrologic properties by changing physical and chemical characteristics of soil. To understand the effect of biochar amendment on soil hydrology, we measured the hydraulic conductivity (K) of biochar-sand mixtures as well as dissolved organic carbon (DOC) in leachate. Specifically, we assessed the effects of biochar concentration and particle size on K and amount of DOC in the soil leachate. To better understand how physical properties influenced K, we also measured the skeletal density of biochars and sand, and the bulk density, the water saturation, and the porosity of biochar-sand mixtures. Our model soil was sand (0.251-0.853 mm) with biochar rates from 2 to 10 wt% (g biochar/g total soil × 100%). As biochar (concentration increased from 0 to 10 wt%, K decreased by 72 ± 3%. When biochar particle size was equal to, greater than, and less than particle size of sand, we found that biochar in different particle sizes have different effects on K. For a 2 wt% biochar rate, K decreased by 72 ± 2% when biochar particles were finer than sand particles, and decreased by 15 ± 2% when biochar particles were coarser than sand particles. When biochar and sand particle size were comparable, we observed no significant effect on K. We propose that the decrease of K through the addition of fine biochar was because finer biochar particles filled spaces between sand particles, which increased tortuosity and reduced pore throat size of the mixture. The decrease of K associated with coarser biochar was caused by the bimodal particle size distribution, resulting in more compact packing and increased tortuosity. The loss of biochar C as DOC was related to both biochar rate and particle size. The cumulative DOC loss was 1350% higher from 10 wt% biochar compared to pure sand. This large increase reflected the very small DOC yield from pure sand. In addition, DOC in the leachate decreased as biochar particle size

  13. Thermal Conductivity Measurement and Analysis of Fully Ceramic Microencapsulated fuel

    Energy Technology Data Exchange (ETDEWEB)

    Lee, H. G.; Kim, D. J.; Park, J. Y.; Kim, W. J. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, S. J. [KEPCO Nuclear Fuel, Daejeon (Korea, Republic of)

    2015-10-15

    FCM nuclear fuel is composed of tristructural isotropic(TRISO) fuel particle and SiC ceramic matrix. SiC ceramic matrix play an essential part in protecting fission product. In the FCM fuel concept, fission product is doubly protected by TRISO coating layer and SiC ceramic matrix in comparison with the current commercial UO2 fuel system of LWR. In addition to a safety enhancement of FCM fuel, thermal conductivity of SiC ceramic matrix is better than that of UO2 fuel. Because the centerline temperature of FCM fuel is lower than that of the current UO2 fuel due to the difference of thermal conductivity of fuel, an operational release of fission products from the fuel can be reduced. SiC ceramic has attracted for nuclear fuel application due to its high thermal conductivity properties with good radiation tolerant properties, a low neutron absorption cross-section and a high corrosion resistance. Thermal conductivity of ceramic matrix composite depends on the thermal conductivity of each component and the morphology of reinforcement materials such as fibers and particles. There are many results about thermal conductivity of fiber-reinforced composite like as SiCf/SiC composite. Thermal conductivity of SiC ceramics and FCM pellets with the volume fraction of TRISO particles were measured and analyzed by analytical models. Polycrystalline SiC ceramics and FCM pellets with TRISO particles were fabricated by hot press sintering with sintering additives. Thermal conductivity of the FCM pellets with TRISO particles of 0 vol.%, 10 vol.%, 20 vol.%, 30 vol.% and 40 vol.% show 68.4, 52.3, 46.8, 43.0 and 34.5 W/mK, respectively. As the volume fraction of TRISO particles increased, the measured thermal conductivity values closely followed the prediction of Maxwell's equation.

  14. Neural Network for Predicting Thermal Conductivity of Knit Materials

    Directory of Open Access Journals (Sweden)

    Faten Fayala, Ph.D.

    2008-12-01

    Full Text Available The major aim of comfort research is to find the comfort temperature for an individual or group. This subjective property can be evaluated by means of thermal conductivity as a physical characteristic of fabric. This phenomenon depends on many fabric parameters and it is difficult to study the effect of ones without changing the others. In addition, the non-linear relationship of fabric parameters and thermal conductivity handicap mathematical modelling. So a neural network approach was used to predict the thermal conductivity of knitting structure as a function of porosity, air permeability, weight and fiber conductivity. Data on thermal conductivity are measured by experiments carried out on jersey knitted structure.

  15. High and low thermal conductivity of amorphous macromolecules

    Science.gov (United States)

    Xie, Xu; Yang, Kexin; Li, Dongyao; Tsai, Tsung-Han; Shin, Jungwoo; Braun, Paul V.; Cahill, David G.

    2017-01-01

    We measure the thermal conductivity, heat capacity and sound velocity of thin films of five polymers, nine polymer salts, and four caged molecules to advance the fundamental understanding of the lower and upper limits to heat conduction in amorphous macromolecules. The thermal conductivities vary by more than one order of magnitude, from 0.06 W m-1K-1 for [6,6]-phenyl-C71-butyric acid methyl ester to 0.67 W m-1K-1 for poly(vinylphosphonic acid calcium salt). Minimum thermal conductivity calculated from the measured sound velocity and effective atomic density is in good agreement with the thermal conductivity of macromolecules with various molecular structures and intermolecular bonding strength.

  16. Measurement of in-plane thermal conductivity in polymer films

    Science.gov (United States)

    Wei, Qingshuo; Uehara, Chinatsu; Mukaida, Masakazu; Kirihara, Kazuhiro; Ishida, Takao

    2016-04-01

    Measuring the in-plane thermal conductivity of organic thermoelectric materials is challenging but is critically important. Here, a method to study the in-plane thermal conductivity of free-standing films (via the use of commercial equipment) based on temperature wave analysis is explored in depth. This subject method required a free-standing thin film with a thickness larger than 10 μm and an area larger than 1 cm2, which are not difficult to obtain for most solution-processable organic thermoelectric materials. We evaluated thermal conductivities and anisotropic ratios for various types of samples including insulating polymers, undoped semiconducting polymers, doped conducting polymers, and one-dimensional carbon fiber bulky papers. This approach facilitated a rapid screening of in-plane thermal conductivities for various organic thermoelectric materials.

  17. Measurement of in-plane thermal conductivity in polymer films

    Directory of Open Access Journals (Sweden)

    Qingshuo Wei

    2016-04-01

    Full Text Available Measuring the in-plane thermal conductivity of organic thermoelectric materials is challenging but is critically important. Here, a method to study the in-plane thermal conductivity of free-standing films (via the use of commercial equipment based on temperature wave analysis is explored in depth. This subject method required a free-standing thin film with a thickness larger than 10 μm and an area larger than 1 cm2, which are not difficult to obtain for most solution-processable organic thermoelectric materials. We evaluated thermal conductivities and anisotropic ratios for various types of samples including insulating polymers, undoped semiconducting polymers, doped conducting polymers, and one-dimensional carbon fiber bulky papers. This approach facilitated a rapid screening of in-plane thermal conductivities for various organic thermoelectric materials.

  18. Manipulating Steady Heat Conduction by Sensu-shaped Thermal Metamaterials

    Science.gov (United States)

    Han, Tiancheng; Bai, Xue; Liu, Dan; Gao, Dongliang; Li, Baowen; Thong, John T. L.; Qiu, Cheng-Wei

    2015-01-01

    The ability to design the control of heat flow has innumerable benefits in the design of electronic systems such as thermoelectric energy harvesters, solid-state lighting, and thermal imagers, where the thermal design plays a key role in performance and device reliability. In this work, we employ one identical sensu-unit with facile natural composition to experimentally realize a new class of thermal metamaterials for controlling thermal conduction (e.g., thermal concentrator, focusing/resolving, uniform heating), only resorting to positioning and locating the same unit element of sensu-shape structure. The thermal metamaterial unit and the proper arrangement of multiple identical units are capable of transferring, redistributing and managing thermal energy in a versatile fashion. It is also shown that our sensu-shape unit elements can be used in manipulating dc currents without any change in the layout for the thermal counterpart. These could markedly enhance the capabilities in thermal sensing, thermal imaging, thermal-energy storage, thermal packaging, thermal therapy, and more domains beyond. PMID:25974383

  19. Manipulating Steady Heat Conduction by Sensu-shaped Thermal Metamaterials.

    Science.gov (United States)

    Han, Tiancheng; Bai, Xue; Liu, Dan; Gao, Dongliang; Li, Baowen; Thong, John T L; Qiu, Cheng-Wei

    2015-05-14

    The ability to design the control of heat flow has innumerable benefits in the design of electronic systems such as thermoelectric energy harvesters, solid-state lighting, and thermal imagers, where the thermal design plays a key role in performance and device reliability. In this work, we employ one identical sensu-unit with facile natural composition to experimentally realize a new class of thermal metamaterials for controlling thermal conduction (e.g., thermal concentrator, focusing/resolving, uniform heating), only resorting to positioning and locating the same unit element of sensu-shape structure. The thermal metamaterial unit and the proper arrangement of multiple identical units are capable of transferring, redistributing and managing thermal energy in a versatile fashion. It is also shown that our sensu-shape unit elements can be used in manipulating dc currents without any change in the layout for the thermal counterpart. These could markedly enhance the capabilities in thermal sensing, thermal imaging, thermal-energy storage, thermal packaging, thermal therapy, and more domains beyond.

  20. Thermal conductivity evaluation of initial stage sintering phenomena

    Science.gov (United States)

    Schlaefer, Constance Elaine

    The onset of sinter bonding and concomitant handling strength is a critical period in the processing of powder metallurgy materials. Mechanical characterization of this evolution during predensification sintering is difficult, due to the fragile nature of the materials. Thermal properties such as thermal diffusivity and thermal conductivity also evolve during the onset of sinter bonding. This research investigates the potential for assessing mechanical strength through thermal diffusivity evaluation, using the non-contact technique of laser flash analysis. Thermal conductivity and transverse rupture strength were evaluated for a nickel powder system in three different formats: injection-molded, low-density die-compacted, and high-density die-compacted. Measurements focused on post-sintering strength and thermal conductivity evolution from 20 to 700°C for the first two formats. In situ strength was evaluated for the high-density die-compacted material. Thermal conductivity was demonstrated to be a linear function of neck diameter, versus a function of the neck area as anticipated. Strength evaluation confirmed previous research that strength is a function of the neck area. Based on both properties' dependence on neck size, an integrated relationship was constructed, allowing mechanical strength to be directly predicted from thermal conductivity measurement for the given system.

  1. Anisotropic thermal conductivity in epoxy-bonded magnetocaloric composites

    Science.gov (United States)

    Weise, Bruno; Sellschopp, Kai; Bierdel, Marius; Funk, Alexander; Bobeth, Manfred; Krautz, Maria; Waske, Anja

    2016-09-01

    Thermal management is one of the crucial issues in the development of magnetocaloric refrigeration technology for application. In order to ensure optimal exploitation of the materials "primary" properties, such as entropy change and temperature lift, thermal properties (and other "secondary" properties) play an important role. In magnetocaloric composites, which show an increased cycling stability in comparison to their bulk counterparts, thermal properties are strongly determined by the geometric arrangement of the corresponding components. In the first part of this paper, the inner structure of a polymer-bonded La(Fe, Co, Si)13-composite was studied by X-ray computed tomography. Based on this 3D data, a numerical study along all three spatial directions revealed anisotropic thermal conductivity of the composite: Due to the preparation process, the long-axis of the magnetocaloric particles is aligned along the xy plane which is why the in-plane thermal conductivity is larger than the thermal conductivity along the z-axis. Further, the study is expanded to a second aspect devoted to the influence of particle distribution and alignment within the polymer matrix. Based on an equivalent ellipsoids model to describe the inner structure of the composite, numerical simulation of the thermal conductivity in different particle arrangements and orientation distributions were performed. This paper evaluates the possibilities of microstructural design for inducing and adjusting anisotropic thermal conductivity in magnetocaloric composites.

  2. Laser X-ray Conversion and Electron Thermal Conductivity*

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The influence of electron thermal conductivity on the laser x-ray conversion in the coupling of 3ωo laser with Au plane target has been investigated by using a non-LTE radiation hydrodynamic code. The non-local electron thermal conductivity is introduced and compared with the other two kinds of the flux-limited Spitzer-Harm description. The results show that the non-local thermal conductivity causes the increase of the laser x-ray conversion efficiency andimportant changes of the plasma state and coupling feature

  3. Phonon Transport and Thermal Conductivity in an Acoustic Filter

    Institute of Scientific and Technical Information of China (English)

    LU Jian-Duo; SHAO Liang; HOU Yang-Lai; YI Lin

    2007-01-01

    We investigate the phonon ballistic transmission and the thermal conductivity in a dielectric quantum structure.It is found that these observable quantities sensitively depend on geometric parameters, and are of quantum character. The total transmission coefficient as a function of the reduced waveguide-length exhibits periodical belaviour and the reduced thermal conductance decreases below the ideal universal value for the low temperature.Our results show that one can control the thermal conductivity of the structure and make all kinds of acoustic filters to match practical requirements in devices by adjustingthe geometric parameters.

  4. Evolution of seismic velocities in heavy oil sand reservoirs during thermal recovery process

    CERN Document Server

    Nauroy, Jean-François; Guy, N; Baroni, Axelle; Delage, Pierre; Mainguy, Marc; 10.2516/ogst/2012027

    2013-01-01

    In thermally enhanced recovery processes like cyclic steam stimulation (CSS) or steam assisted gravity drainage (SAGD), continuous steam injection entails changes in pore fluid, pore pressure and temperature in the rock reservoir, that are most often unconsolidated or weakly consolidated sandstones. This in turn increases or decreases the effective stresses and changes the elastic properties of the rocks. Thermally enhanced recovery processes give rise to complex couplings. Numerical simulations have been carried out on a case study so as to provide an estimation of the evolution of pressure, temperature, pore fluid saturation, stress and strain in any zone located around the injector and producer wells. The approach of Ciz and Shapiro (2007) - an extension of the poroelastic theory of Biot-Gassmann applied to rock filled elastic material - has been used to model the velocity dispersion in the oil sand mass under different conditions of temperature and stress. A good agreement has been found between these pre...

  5. Analysis of sources of bulk conductivity change in saturated silica sand after unbuffered TCE oxidation by permanganate.

    Science.gov (United States)

    Hort, Ryan D; Revil, André; Munakata-Marr, Junko

    2014-09-01

    Time lapse resistivity surveys could potentially improve monitoring of permanganate-based in situ chemical oxidation (ISCO) of organic contaminants such as trichloroethene (TCE) by tracking changes in subsurface conductivity that result from injection of permanganate and oxidation of the contaminant. Bulk conductivity and pore fluid conductivity changes during unbuffered TCE oxidation using permanganate are examined through laboratory measurements and conductivity modeling using PHREEQC in fluid samples and porous media samples containing silica sand. In fluid samples, oxidation of one TCE molecule produces three chloride ions and one proton, resulting in an increase in fluid electrical conductivity despite the loss of two permanganate ions in the reaction. However, in saturated sand samples in which up to 8mM TCE was oxidized, at least 94% of the fluid conductivity associated with the presence of protons was removed within 3h of sand contact, most likely through protonation of silanol groups found on the surface of the sand grains. Minor conductivity effects most likely associated with pH-dependent reductive dissolution of manganese dioxide were also observed but not accounted for in pore-fluid conductivity modeling. Unaccounted conductivity effects resulted in an under-calculation of post-reaction pore fluid conductivity of 2.1% to 5.5%. Although small increases in the porous media formation factor resulting from precipitation of manganese dioxide were detected (about 3%), these increases could not be confirmed to be statistically significant. Both injection of permanganate and oxidation of TCE cause increases in bulk conductivity that would be detectable through time-lapse resistivity surveys in field conditions.

  6. In-Pile Thermal Conductivity Measurement Method for Nuclear Fuels

    Energy Technology Data Exchange (ETDEWEB)

    Joy L. Rempe; Brandon Fox; Heng Ban; Joshua E. Daw; Darrell L. Knudson; Keith G. Condie

    2009-08-01

    Thermophysical properties of advanced nuclear fuels and materials during irradiation must be known prior to their use in existing, advanced, or next generation reactors. Thermal conductivity is one of the most important properties for predicting fuel and material performance. A joint Utah State University (USU) / Idaho National Laboratory (INL) project, which is being conducted with assistance from the Institute for Energy Technology at the Norway Halden Reactor Project, is investigating in-pile fuel thermal conductivity measurement methods. This paper focuses on one of these methods – a multiple thermocouple method. This two-thermocouple method uses a surrogate fuel rod with Joule heating to simulate volumetric heat generation to gain insights about in-pile detection of thermal conductivity. Preliminary results indicated that this method can measure thermal conductivity over a specific temperature range. This paper reports the thermal conductivity values obtained by this technique and compares these values with thermal property data obtained from standard thermal property measurement techniques available at INL’s High Test Temperature Laboratory. Experimental results and material properties data are also compared to finite element analysis results.

  7. Remarkable reduction of thermal conductivity in phosphorene phononic crystal.

    Science.gov (United States)

    Xu, Wen; Zhang, Gang

    2016-05-05

    Phosphorene has received much attention due to its interesting physical and chemical properties, and its potential applications such as thermoelectricity. In thermoelectric applications, low thermal conductivity is essential for achieving a high figure of merit. In this work, we propose to reduce the thermal conductivity of phosphorene by adopting the phononic crystal structure, phosphorene nanomesh. With equilibrium molecular dynamics simulations, we find that the thermal conductivity is remarkably reduced in the phononic crystal. Our analysis shows that the reduction is due to the depressed phonon group velocities induced by Brillouin zone folding, and the reduced phonon lifetimes in the phononic crystal. Interestingly, it is found that the anisotropy ratio of thermal conductivity could be tuned by the 'non-square' pores in the phononic crystal, as the phonon group velocities in the direction with larger projection of pores is more severely suppressed, leading to greater reduction of thermal conductivity in this direction. Our work provides deep insight into thermal transport in phononic crystals and proposes a new strategy to reduce the thermal conductivity of monolayer phosphorene.

  8. Lattice thermal conductivity of minerals in the deep mantle condition

    Science.gov (United States)

    Dekura, H.; Tsuchiya, T.; Tsuchiya, J.

    2011-12-01

    Thermal transport property of materials under pressure and temperature is of importance for understanding the dynamics of the solid Earth and the thermal history. Both experimental and theoretical determinations of the thermal conductivity, however, still remain technically challenging particularly at the deep mantle condition. Recent progress in ab initio computational method based on the density-functional theory is now makes it possible to examine the transport phenomena including the lattice thermal conduction. The intrinsic bulk thermal conduction of insulator is caused by lattice anharmonicity owing to phonon-phonon interaction. The key parameter to predict lattice thermal conductivity is thus the anharmonic coupling constant. Earlier theoretical works calculated the lattice thermal conductivity of MgO with ab initio molecular dynamics simulation or finite difference lattice dynamics simulation (Nico de Koker, Phys. Rev. Lett. 103, 125902, 2009; X. Tang and J. Dong, Proc. Natl. Acad. Sci. U.S.A. 107, 4539, 2010). However, in these approaches, the simulation cell size could often be insufficient for accurate description of the long wavelength phonon scattering. This leads to a lack of the decay channels for the phonons. As an alternative approach, the anharmonic coupling strength between phonon modes can be evaluated within the density-functional perturbation theory. In this approach, the higher-order force tensors are calculated through a number of phonon decay channels obtained within the perturbative scheme taking care only of the primitive cell. We have been developing a technique for calculation of the phonon linewidth necessary to obtain the phonon lifetime. Then the lattice thermal conductivity is evaluated combining with additional harmonic-level of propeties. In this presentation, we show the behavior of lattice thermal conductivity in lower mantle minerals, and discuss the effects of pressure and temperature on their conductivities up to the deep

  9. Thermal conductivity of polymer composites with oriented boron nitride

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Hong Jun; Eoh, Young Jun [Department of Materials Engineering, Kyonggi University, Suwon (Korea, Republic of); Park, Sung Dae [Electronic Materials and Device Research Center, Korea Electronics Technology Institute, Seongnam (Korea, Republic of); Kim, Eung Soo, E-mail: eskim@kyonggi.ac.kr [Department of Materials Engineering, Kyonggi University, Suwon (Korea, Republic of)

    2014-08-20

    Highlights: • Thermal conductivity depended on the orientation of BN in the polymer matrices. • Hexagonal boron nitride (BN) particles were treated by C{sub 27}H{sub 27}N{sub 3}O{sub 2} and C{sub 14}H{sub 6}O{sub 8}. • Amphiphilic-agent-treated BN particles are more easily oriented in the composite. • BN/PVA composites with C{sub 14}H{sub 6}O{sub 8}-treated BN showed the highest thermal conductivity. • Thermal conductivity of the composites was compared with several theoretical models. - Abstract: Thermal conductivity of boron nitride (BN) with polyvinyl alcohol (PVA) and/or polyvinyl butyral (PVB) was investigated as a function of the degree of BN orientation, the numbers of hydroxyl groups in the polymer matrices and the amphiphilic agents used. The composites with in-plane orientation of BN showed a higher thermal conductivity than the composites with out-of-plane orientation of BN due to the increase of thermal pathway. For a given BN content, the composites with in-plane orientation of BN/PVA showed higher thermal conductivity than the composites with in-plane orientation of BN/PVB. This result could be attributed to the improved degree of orientation of BN, caused by a larger number of hydroxyl groups being present. Those treated with C{sub 14}H{sub 6}O{sub 8} amphiphilic agent demonstrated a higher thermal conductivity than those treated by C{sub 27}H{sub 27}N{sub 3}O{sub 2}. The measured thermal conductivity of the composites was compared with that predicted by the several theoretical models.

  10. Fabrication and Characterization of a Conduction Cooled Thermal Neutron Filter

    Energy Technology Data Exchange (ETDEWEB)

    Heather Wampler; Adam Gerth; Heng Ban; Donna Post Guillen; Douglas Porter; Cynthia Papesch

    2010-06-01

    Installation of a conduction cooled thermal (low-energy) neutron filter in an existing domestic test reactor would provide the U.S. the capability to test new reactor fuels and materials for advanced fast (high-energy) reactor concepts. A composite consisting of Al3Hf-Al has been proposed for the neutron filter due to both the neutron filtering properties of hafnium and the conducting capabilities of aluminum. Knowledge of the thermal conductivity of the Al3Hf-Al composite is essential for the design of the filtering system. The present objectives are to identify a suitable fabrication technique and to measure the thermophysical properties of the Al3Hf intermetallic, which has not been done previous to this study. A centrifugal casting method was used to prepare samples of Al3Hf. X-ray diffraction and Rietveld analysis were conducted to determine the structural make-up of each of the samples. Thermophysical properties were measured as follows: specific heat by a differential scanning calorimeter (DSC), thermal diffusivity by a laser flash thermal diffusivity measuring system, thermal expansion by a dilatometer, and thermal conductivity was calculated based on the previous measurements. All measurements were acquired over a temperature range of 90°C - 375°C with some measurements outside these bounds. The average thermal conductivity of the intermetallic Al3Hf (~7 at.% Hf) was found to be ~ 41 W/m-K for the given temperature range. This information fills a knowledge gap in the thermophysical properties of the intermetallic Al3Hf with the specified percentage of hafnium. A model designed to predict composite properties was used to calculate a thermal conductivity of ~177 W/m-K for an Al3Hf-Al composite with 23 vol% Al3Hf. This calculation was based upon the average thermal conductivity of Al3Hf over the specified temperature range.

  11. Modeling of Thermal Conductivity of Graphite Nanosheet Composites

    Science.gov (United States)

    Lin, Wei; Zhang, Rongwei; Wong, C. P.

    2010-03-01

    Recent experiments demonstrated a very high thermal conductivity in graphite nanosheet (GNS)/epoxy nanocomposites; however, theoretical analysis is lacking. In this letter, an effective medium model has been used to analyze the effective thermal conductivity of the GNS/polymer nanocomposites and has shown good validity. Strong influences of the aspect ratio and the orientation of the GNS are evident. As expected, interfacial thermal resistance still plays a role in determining the overall thermal transport in the GNS/polymer nanocomposites. In comparison with the interfacial thermal resistance between carbon nanotubes and polymers, the interfacial thermal resistance between GNS and polymers is about one order of magnitude lower, the reason for which is discussed.

  12. Influence of thermalization on thermal conduction through molecular junctions: Computational study of PEG oligomers

    Science.gov (United States)

    Pandey, Hari Datt; Leitner, David M.

    2017-08-01

    Thermalization in molecular junctions and the extent to which it mediates thermal transport through the junction are explored and illustrated with computational modeling of polyethylene glycol (PEG) oligomer junctions. We calculate rates of thermalization in the PEG oligomers from 100 K to 600 K and thermal conduction through PEG oligomer interfaces between gold and other materials, including water, motivated in part by photothermal applications of gold nanoparticles capped by PEG oligomers in aqueous and cellular environments. Variation of thermalization rates over a range of oligomer lengths and temperatures reveals striking effects of thermalization on thermal conduction through the junction. The calculated thermalization rates help clarify the scope of applicability of approaches that can be used to predict thermal conduction, e.g., where Fourier's law breaks down and where a Landauer approach is suitable. The rates and nature of vibrational energy transport computed for PEG oligomers are compared with available experimental results.

  13. Experimental investigation of thermal conductivity coefficient and heat exchange between fluidized bed and inclined exchange surface

    Directory of Open Access Journals (Sweden)

    B. Stojanovic

    2009-06-01

    Full Text Available The paper presents experimental research of thermal conductivity coefficients of the siliceous sand bed fluidized by air and an experimental investigation of the particle size influence on the heat transfer coefficient between fluidized bed and inclined exchange surfaces. The measurements were performed for the specific fluidization velocity and sand particle diameters d p=0.3, 0.5, 0.9 mm. The industrial use of fluidized beds has been increasing rapidly in the past 20 years owing to their useful characteristics. One of the outstanding characteristics of a fluidized bed is that it tends to maintain a uniform temperature even with nonuniform heat release. On the basis of experimental research, the influence of the process's operational parameters on the obtained values of the bed's thermal conductivity has been analyzed. The results show direct dependence of thermal conductivity on the intensity of mixing, the degree of fluidization, and the size of particles. In the axial direction, the coefficients that have been treated have values a whole order higher than in the radial direction. Comparison of experimental research results with experimental results of other authors shows good agreement and the same tendency of thermal conductivity change. It is well known in the literature that the value of the heat transfer coefficient is the highest in the horizontal and the smallest in the vertical position of the heat exchange surface. Variation of heat transfer, depending on inclination angle is not examined in detail. The difference between the values of the relative heat transfer coefficient between vertical and horizontal heater position for all particle sizes reduces by approximately 15% with the increase of fluidization rate.

  14. Thermal conductivity of microPCMs-filled epoxy matrix composites

    NARCIS (Netherlands)

    Su, J.F.; Wang, X.Y; Huang, Z.; Zhao, Y.H.; Yuan, X.Y.

    2011-01-01

    Microencapsulated phase change materials (microPCMs) have been widely applied in solid matrix as thermal-storage or temperature-controlling functional composites. The thermal conductivity of these microPCMs/matrix composites is an important property need to be considered. In this study, a series of

  15. Thermal Conduction in Systems out of Hydrostatic Equilibrium

    CERN Document Server

    Herrera, L; Hernández-Pastora, J L; Martín, J; Martínez, J

    1997-01-01

    We analyse the effects of thermal conduction in a relativistic fluid, just after its departure from hydrostatic equilibrium, on a time scale of the order of thermal relaxation time. It is obtained that the resulting evolution will critically depend on a parameter defined in terms of thermodynamic variables, which is constrained by causality requirements.

  16. Thermal Conductivity in Suspension Sprayed Thermal Barrier Coatings: Modeling and Experiments

    Science.gov (United States)

    Ganvir, Ashish; Kumara, Chamara; Gupta, Mohit; Nylen, Per

    2016-12-01

    Axial suspension plasma spraying (ASPS) can generate microstructures with higher porosity and pores in the size range from submicron to nanometer. ASPS thermal barrier coatings (TBC) have already shown a great potential to produce low thermal conductivity coatings for gas turbine applications. It is important to understand the fundamental relationships between microstructural defects in ASPS coatings such as crystallite boundaries, porosity etc. and thermal conductivity. Object-oriented finite element (OOF) analysis has been shown as an effective tool for evaluating thermal conductivity of conventional TBCs as this method is capable of incorporating the inherent microstructure in the model. The objective of this work was to analyze the thermal conductivity of ASPS TBCs using experimental techniques and also to evaluate a procedure where OOF can be used to predict and analyze the thermal conductivity for these coatings. Verification of the model was done by comparing modeling results with the experimental thermal conductivity. The results showed that the varied scaled porosity has a significant influence on the thermal conductivity. Smaller crystallites and higher overall porosity content resulted in lower thermal conductivity. It was shown that OOF could be a powerful tool to predict and rank thermal conductivity of ASPS TBCs.

  17. Thermal Conductivity in Suspension Sprayed Thermal Barrier Coatings: Modeling and Experiments

    Science.gov (United States)

    Ganvir, Ashish; Kumara, Chamara; Gupta, Mohit; Nylen, Per

    2017-01-01

    Axial suspension plasma spraying (ASPS) can generate microstructures with higher porosity and pores in the size range from submicron to nanometer. ASPS thermal barrier coatings (TBC) have already shown a great potential to produce low thermal conductivity coatings for gas turbine applications. It is important to understand the fundamental relationships between microstructural defects in ASPS coatings such as crystallite boundaries, porosity etc. and thermal conductivity. Object-oriented finite element (OOF) analysis has been shown as an effective tool for evaluating thermal conductivity of conventional TBCs as this method is capable of incorporating the inherent microstructure in the model. The objective of this work was to analyze the thermal conductivity of ASPS TBCs using experimental techniques and also to evaluate a procedure where OOF can be used to predict and analyze the thermal conductivity for these coatings. Verification of the model was done by comparing modeling results with the experimental thermal conductivity. The results showed that the varied scaled porosity has a significant influence on the thermal conductivity. Smaller crystallites and higher overall porosity content resulted in lower thermal conductivity. It was shown that OOF could be a powerful tool to predict and rank thermal conductivity of ASPS TBCs.

  18. Anisotropic Tuning of Graphite Thermal Conductivity by Lithium Intercalation.

    Science.gov (United States)

    Qian, Xin; Gu, Xiaokun; Dresselhaus, Mildred S; Yang, Ronggui

    2016-11-17

    Understanding thermal transport in lithium intercalated layered materials is not only important for managing heat generation and dissipation in lithium ion batteries but also the understanding potentially provides a novel way to design materials with reversibly tunable thermal conductivity. In this work, the thermal conductivity of lithium-graphite intercalation compounds (LixC6) is calculated using molecular dynamics simulations as a function of the amount of lithium intercalated. We found that intercalation of lithium has an anisotropic effect on tuning the thermal conductivity: the thermal conductivity in the basal plane decreases monotonically from 1232 W/m·K of pristine graphite to 444 W/m·K of the fully lithiated LiC6, while the thermal conductivity along the c-axis decreases first from 6.5 W/m·K for graphite to 1.3 W/m·K for LiC18 and then increases to 5.0 W/m·K for LiC6 as the lithium composition increases. More importantly, we provide the very first atomic-scale insight into the effect of lithium intercalation on the spectral phonon properties of graphite. The intercalated lithium ions are found to suppress the phonon lifetime and to reduce the group velocity of phonons parallel to the basal plane but significantly to increase the phonon group velocity along the c-axis, which anisotropically tunes the thermal conductivity of lithiated graphite compounds. This work could shed some light on the search for tunable thermal conductivity materials and might have strong impacts on the thermal management of lithium ion batteries.

  19. The impact of hydrate saturation on the mechanical, electrical, and thermal properties of hydrate-bearing sand, silts, and clay

    Energy Technology Data Exchange (ETDEWEB)

    Santamarina, J.C. [Georgia Inst. of Technology, Atlanta, GA (United States). School of Civil and Environmental Engineering; Ruppel, C. [United States Geological Survey, Woods Hole, MA (United States)

    2008-07-01

    A study was conducted to provide an internally-consistent, systematically-acquired database that could help in evaluating gas hydrate reservoirs. Other objectives were to assist in geomechanical analyses, hazards evaluation and the development of methane hydrate production techniques in sandy lithologies and fine-grained sediments that exist in the northern Gulf of Mexico. An understanding of the physical properties of hydrate-bearing sediments facilitates the interpretation of geophysical field data, borehole and slope stability analyses, and reservoir simulation and production models. This paper reported on the key findings derived from 5 years of laboratory experiments conducted on synthetic samples of sand, silts, or clays subjected to various confining pressures. The samples contained controlled saturations of tetrahydrofuran hydrate formed from the dissolved phase. This internally-consistent data set was used to conduct a comprehensive analysis of the trends in geophysical and geotechnical properties as a function of hydrate saturation, soil characteristics, and other parameters. The experiments emphasized measurements of seismic velocities, electrical conductivity and permittivity, large strain deformation and strength, and thermal conductivity. The impact of hydrate formation technique on the resulting physical properties measurements were discussed. The data set was used to identify systematic effects of sediment characteristics, hydrate concentration, and state of stress. The study showed that the electrical properties of hydrate-bearing sediments are less sensitive to the method used to form hydrate in the laboratory than to hydrate saturation. It was concluded that mechanical properties are strongly influenced by both soil properties and the hydrate loci. Since the thermal conductivity depends on the interaction of several factors, it cannot be readily predicted by volume average formulations. 23 refs., 2 tabs., 9 figs.

  20. Predicting the effective thermal conductivity of carbon nanotube based nanofluids

    Energy Technology Data Exchange (ETDEWEB)

    Sastry, N N Venkata; Bhunia, Avijit; Sundararajan, T; Das, Sarit K [Department of Mechanical Engineering, Indian Institute of Technology, Madras, Chennai 600 036 (India)

    2008-02-06

    Adding a small volume fraction of carbon nanotubes (CNTs) to a liquid enhances the thermal conductivity significantly. Recent experimental findings report an anomalously wide range of enhancement values that continue to perplex the research community and remain unexplained. In this paper we present a theoretical model based on three-dimensional CNT chain formation (percolation) in the base liquid and the corresponding thermal resistance network. The model considers random CNT orientation and CNT-CNT interaction forming the percolating chain. Predictions are in good agreement with almost all available experimental data. Results show that the enhancement critically depends on the CNT geometry (length), volume fraction, thermal conductivity of the base liquid and the nanofluid (CNT-liquid suspension) preparation technique. Based on the physical mechanism of heat conduction in the nanofluid, we introduce a new dimensionless parameter that alone characterizes the nanofluid thermal conductivity with reasonable accuracy ({approx} {+-} 5%)

  1. Enhanced thermal conductivity through the development of nanofluids

    Energy Technology Data Exchange (ETDEWEB)

    Eastman, J.A.; Choi, U.S.; Li, S.; Thompson, L.J.; Lee, S.

    1996-11-01

    Low thermal conductivity is a primary limitation in the development of energy-efficient heat transfer fluids required in many industrial applications. To overcome this limitation, a new class of heat transfer fluids is being developed by suspending nanocrystalline particles in liquids such as water or oil. The resulting nanofluids possess extremely high thermal conductivities compared to the liquids without dispersed nanocrystalline particles. For example, 5 volume % of nanocrystalline copper oxide particles suspended in water results in an improvement in thermal conductivity of almost 60% compared to water without nanoparticles. Excellent suspension properties are also observed, with no significant settling of nanocrystalline oxide particles occurring in stationary fluids over time periods longer than several days. Direct evaporation of Cu nanoparticles into pump oil results in similar improvements in thermal conductivity compared to oxide-in-water systems, but importantly, requires far smaller concentrations of dispersed nanocrystalline powder.

  2. Evidence for enhanced thermal conduction through percolating structures in nanofluids

    Energy Technology Data Exchange (ETDEWEB)

    Philip, John; Shima, P D; Raj, Baldev [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603 102, Tamilnadu (India)], E-mail: philip@igcar.gov.in

    2008-07-30

    The unusually large enhancement of thermal conductivity (k/k{sub f}{approx}4.0, where k and k{sub f} are the thermal conductivities of the nanofluid and the base fluid, respectively) observed in a nanofluid containing linear chain-like aggregates provides direct evidence for efficient transport of heat through percolating paths. The nanofluid used was a stable colloidal suspension of magnetite (Fe{sub 3}O{sub 4}) nanoparticles of average diameter 6.7 nm, coated with oleic acid and dispersed in kerosene. The maximum enhancement under magnetic field was about 48{phi} (where {phi} is the volume fraction). The maximum enhancement is observed when chain-like aggregates are uniformly dispersed without clumping. These results also suggest that nanofluids containing well-dispersed nanoparticles (without aggregates) do not exhibit significant enhancement of thermal conductivity. Our findings offer promising applications for developing a new generation of nanofluids with tunable thermal conductivity.

  3. Predicting the effective thermal conductivity of carbon nanotube based nanofluids.

    Science.gov (United States)

    Venkata Sastry, N N; Bhunia, Avijit; Sundararajan, T; Das, Sarit K

    2008-02-06

    Adding a small volume fraction of carbon nanotubes (CNTs) to a liquid enhances the thermal conductivity significantly. Recent experimental findings report an anomalously wide range of enhancement values that continue to perplex the research community and remain unexplained. In this paper we present a theoretical model based on three-dimensional CNT chain formation (percolation) in the base liquid and the corresponding thermal resistance network. The model considers random CNT orientation and CNT-CNT interaction forming the percolating chain. Predictions are in good agreement with almost all available experimental data. Results show that the enhancement critically depends on the CNT geometry (length), volume fraction, thermal conductivity of the base liquid and the nanofluid (CNT-liquid suspension) preparation technique. Based on the physical mechanism of heat conduction in the nanofluid, we introduce a new dimensionless parameter that alone characterizes the nanofluid thermal conductivity with reasonable accuracy (∼ ± 5%).

  4. Evidence for enhanced thermal conduction through percolating structures in nanofluids.

    Science.gov (United States)

    Philip, John; Shima, P D; Raj, Baldev

    2008-07-30

    The unusually large enhancement of thermal conductivity (k/k(f)∼4.0, where k and k(f) are the thermal conductivities of the nanofluid and the base fluid, respectively) observed in a nanofluid containing linear chain-like aggregates provides direct evidence for efficient transport of heat through percolating paths. The nanofluid used was a stable colloidal suspension of magnetite (Fe(3)O(4)) nanoparticles of average diameter 6.7 nm, coated with oleic acid and dispersed in kerosene. The maximum enhancement under magnetic field was about 48φ (where φ is the volume fraction). The maximum enhancement is observed when chain-like aggregates are uniformly dispersed without clumping. These results also suggest that nanofluids containing well-dispersed nanoparticles (without aggregates) do not exhibit significant enhancement of thermal conductivity. Our findings offer promising applications for developing a new generation of nanofluids with tunable thermal conductivity.

  5. Cryogenic Thermal Conductivity Measurements on Candidate Materials for Space Missions

    Science.gov (United States)

    Tuttle, JIm; Canavan, Ed; Jahromi, Amir

    2017-01-01

    Spacecraft and instruments on space missions are built using a wide variety of carefully-chosen materials. In addition to having mechanical properties appropriate for surviving the launch environment, these materials generally must have thermal conductivity values which meet specific requirements in their operating temperature ranges. Space missions commonly propose to include materials for which the thermal conductivity is not well known at cryogenic temperatures. We developed a test facility in 2004 at NASAs Goddard Space Flight Center to measure material thermal conductivity at temperatures between 4 and 300 Kelvin, and we have characterized many candidate materials since then. The measurement technique is not extremely complex, but proper care to details of the setup, data acquisition and data reduction is necessary for high precision and accuracy. We describe the thermal conductivity measurement process and present results for several materials.

  6. Thermal conductivity of newspaper sandwiched aerated lightweight concrete panel

    Energy Technology Data Exchange (ETDEWEB)

    Ng, Soon-Ching; Low, Kaw-Sai [Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Jalan Genting Kelang, Setapak, 53300 Kuala Lumpur, Wilayah Persekutuan (Malaysia)

    2010-12-15

    Investigation on the thermal conductivity of newspaper sandwiched aerated lightweight concrete (ALC) panels is the main purpose of this study. Various densities of ALC panels ranging from 1700, 1400 and 1100 kg/m{sup 3} with three different aerial intensities of newspaper sandwiched were produced. Investigation was limited to the effect of aerial intensity of newspaper sandwiched and the effect of density of ALC on thermal conductivity. It is found that the thermal conductivity of newspaper sandwiched ALC panels reduced remarkably compared to control ALC panels. The reduction was recorded at 18.0%, 21.8% and 20.7% correspond to densities of 1700, 1400 and 1100 kg/m{sup 3} with just a mere 0.05 g/cm{sup 2} aerial intensity of newspaper sandwiched. Newspaper sandwiched has a significant impact on the performance of thermal conductivity of ALC panels based on regression analysis. (author)

  7. Thermal conductance of pressed brass contacts at liquid helium temperatures

    Science.gov (United States)

    Salerno, L. J.; Kittel, P.; Brooks, W. F.; Spivak, A. L.; Marks, W. G., Jr.

    1986-01-01

    An apparatus has been designed and fabricated which will measure the thermal conductance of pressed contacts at liquid helium temperatures as a function of applied force, with surface finish as a parameter. The apparatus is automated and was used to measure thermal conductance at temperatures from 1.5 to 6.5 K at applied forces up to 700 N for brass sample pairs having surface finishes from 0.1 to 1.6 micron rms. The experimental data were found to fit a simple power law where the thermal conductance is given by k = alpha T exp n, where k is the thermal conductance, T is the absolute temperature, and alpha and n are empirically determined constants.

  8. Thermal conductivity measurements at cryogenic temperatures at LASA

    Energy Technology Data Exchange (ETDEWEB)

    Broggi, F.; Pedrini, D.; Rossi, L. [INFN, Milan (Italy)]|[Laboratorio LASA, Segrate, Milan (Italy)

    1995-08-01

    Here the improvement realised to have better control of the reference junction temperature and measurements carried out on Nb{sub 3}Sn cut out from 2 different coils (named LASA3 and LASA5), showing the difference between the longitudinal and the transverse thermal conductivity, is described. Two different methods of data analysis are presented, the DAM (derivative approximated method) and the TCI (thermal conductivity integral). The data analysis for the tungsten and the LASA5 coil has been done according to the two methods showing that the TCI method with polynomial functions is not adequate to describe the thermal conductivity. Only a polynomial fit based on the TCI method but limited at a lower order than the nominal, when the data are well distributed along the range of measurements, can describe reasonably the thermal conductivity dependence with the temperature. Finally the measurements on a rod of BSCCO 2212 high T{sub c} superconductor are presented.

  9. Advanced Low Conductivity Thermal Barrier Coatings: Performance and Future Directions

    Science.gov (United States)

    Zhu, Dongming; Miller, Robert A.

    2008-01-01

    Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future engine higher fuel efficiency and lower emission goals. In this presentation, thermal barrier coating development considerations and performance will be emphasized. Advanced thermal barrier coatings have been developed using a multi-component defect clustering approach, and shown to have improved thermal stability and lower conductivity. The coating systems have been demonstrated for high temperature combustor applications. For thermal barrier coatings designed for turbine airfoil applications, further improved erosion and impact resistance are crucial for engine performance and durability. Erosion resistant thermal barrier coatings are being developed, with a current emphasis on the toughness improvements using a combined rare earth- and transition metal-oxide doping approach. The performance of the toughened thermal barrier coatings has been evaluated in burner rig and laser heat-flux rig simulated engine erosion and thermal gradient environments. The results have shown that the coating composition optimizations can effectively improve the erosion and impact resistance of the coating systems, while maintaining low thermal conductivity and cyclic durability. The erosion, impact and high heat-flux damage mechanisms of the thermal barrier coatings will also be described.

  10. Thermal conductivity, electrical conductivity and specific heat of copper-carbon fiber composite

    Science.gov (United States)

    Kuniya, Keiichi; Arakawa, Hideo; Kanai, Tsuneyuki; Chiba, Akio

    1988-01-01

    A new material of copper/carbon fiber composite is developed which retains the properties of copper, i.e., its excellent electrical and thermal conductivity, and the property of carbon, i.e., a small thermal expansion coefficient. These properties of the composite are adjustable within a certain range by changing the volume and/or the orientation of the carbon fibers. The effects of carbon fiber volume and arrangement changes on the thermal and electrical conductivity, and specific heat of the composite are studied. Results obtained are as follows: the thermal and electrical conductivity of the composite decrease as the volume of the carbon fiber increases, and were influenced by the fiber orientation. The results are predictable from a careful application of the rule of mixtures for composites. The specific heat of the composite was dependent, not on fiber orientation, but on fiber volume. In the thermal fatigue tests, no degradation in the electrical conductivity of this composite was observed.

  11. Identification of temperature-dependent thermal conductivity and experimental verification

    Science.gov (United States)

    Pan, Weizhen; Yi, Fajun; Zhu, Yanwei; Meng, Songhe

    2016-07-01

    A modified Levenberg-Marquardt method (LMM) for the identification of temperature-dependent thermal conductivity is proposed; the experiment and structure of the specimen for identification are also designed. The temperature-dependent thermal conductivities of copper C10200 and brass C28000 are identified to verify the effectiveness of the proposed identification method. The comparison between identified results and the measured data of laser flash diffusivity apparatus indicates the fine consistency and potential usage of the proposed method.

  12. APPLICATION OF NUMERICAL SIMULATION TO STUDY ON THERMAL CONDUCTION

    Institute of Scientific and Technical Information of China (English)

    C. Zhu; Z. Xu; D.E. Wu

    2004-01-01

    In this paper, using computer simulation and mathematic experiment method to solve the simplified one dimensional thermal conduction equation and to obtain the temperature distribution in a metal bar when its one end was heated. According to principle of hot expansion, a holograph of temperature distribution in the bar by laser holotechnique was taken. The results of numerical simulation and experiments are in good agreement and a new method for study on thermal conduction by laser holo-technique was found.

  13. Studies and Properties of Ceramics with High Thermal Conductivity

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The sintering technology of the AlN ceramics power were discussed. It is discussed that the compound sintering aids is consistent with the enhancement of the the thermal conductivity of AlN ceramics, and sintering technics is helped to the improvement of density. It is analyzed how to sinter machinable AlN ceramics with high thermal conductivity. And the microstructure of compound ceramics based on AlN was studied.

  14. Thermal conductivities of some lead and bismuth glasses

    NARCIS (Netherlands)

    Velden, P.F. van

    1965-01-01

    Thermal conductivities have been measured, mainly at 40°C, of glasses within the systems PbO-Bi2O3-SiO2, PbO-Bi2O3-Al2O3-SiO2, and BaO- (Bi2O3 or PbO) -SiO2. Aiming at lowest thermal conductivity, preference was given to glasses of low silica and low alumina contents. Glass formation persists at rat

  15. Dependence of thermal conductivity on structural parameters in porous samples

    OpenAIRE

    L. Miettinen; Kekäläinen, P; T. Turpeinen; Hyväluoma, J; Merikoski, J.; J. Timonen

    2012-01-01

    The in-plane thermal conductivity of porous sintered bronze plates was studied both experimentally and numerically. We developed and validated an experimental setup, where the sample was placed in vacuum and heated while its time-dependent temperature field was measured with an infrared camera. The porosity and detailed three-dimensional structure of the samples were determined by X-ray microtomography. Lattice-Boltzmann simulations of thermal conductivity in the tomographic reconstructions o...

  16. Graphene nanoplatelets: Thermal diffusivity and thermal conductivity by the flash method

    Science.gov (United States)

    Potenza, M.; Cataldo, A.; Bovesecchi, G.; Corasaniti, S.; Coppa, P.; Bellucci, S.

    2017-07-01

    The present work deals with the measurement of thermo-physical properties of a freestanding sheet of graphene (thermal diffusivity and thermal conductivity), and their dependence on sample density as result of uniform mechanical compression. Thermal diffusivity of graphene nano-platelets (thin slabs) was measured by the pulse flash method. Obtained response data were processed with a specifically developed least square data processing algorithm. GNP specific heat was assumed from literature and thermal conductivity derived from thermal diffusivity, specific heat and density. Obtained results show a significant difference with respect to other porous media: the thermal diffusivity decreases as the density increases, while thermal conductivity increases for low and high densities, and remain fairly constant for the intermediate range. This can be explained by the very high thermal conductivity values reached by the nano-layers of graphene and the peculiar arrangement of platelets during the compression applied to the samples to get the desired density. Due to very high thermal conductivity of graphene layers, the obtained results show that thermal conductivity of conglomerates increases when there is an air reduction due to compression, and consequent density increases, with the number of contact points between platelets also increased. In the intermediate range (250 ≤ ρ ≤ 700 kg.m-3) the folding of platelets reduces density, without increasing the contact points of platelets, so thermal conductivity can slightly decrease.

  17. Metallic coatings for enhancement of thermal contact conductance

    Science.gov (United States)

    Lambert, M. A.; Fletcher, L. S.

    1994-04-01

    The reliability of standard electronic modules may be improved by decreasing overall module temperature. This may be accomplished by enhancing the thermal contact conductance at the interface between the module frame guide rib and the card rail to which the module is clamped. Some metallic coatings, when applied to the card rail, would deform under load, increasing the contact area and associated conductance. This investigation evaluates the enhancements in thermal conductance afforded by vapor deposited silver and gold coatings. Experimental thermal conductance measurements were made for anodized aluminum 6101-T6 and electroless nickel-plated copper C11000-H03 card materials to the aluminum A356-T61 rail material. Conductance values for the electroless nickel-plated copper junction ranged from 600 to 2800 W/m(exp 2)K and those for the anodized aluminum junction ranged from 25 to 91 W/m(exp 2)K for contact pressures of 0.172-0.862 MPa and mean junction temperatures of 20-100 C. Experimental thermal conductance values of vapor deposited silver- and gold-coated aluminum A356-T61 rail surfaces indicate thermal enhancements of 1.25-2.19 for the electroless nickel-plated copper junctions and 1.79-3.41 for the anodized aluminum junctions. The silver and gold coatings provide significant thermal enhancement; however, these coating-substrate combinations are susceptible to galvanic corrosion under some conditions.

  18. Toward nanofluids of ultra-high thermal conductivity.

    Science.gov (United States)

    Wang, Liqiu; Fan, Jing

    2011-02-18

    The assessment of proposed origins for thermal conductivity enhancement in nanofluids signifies the importance of particle morphology and coupled transport in determining nanofluid heat conduction and thermal conductivity. The success of developing nanofluids of superior conductivity depends thus very much on our understanding and manipulation of the morphology and the coupled transport. Nanofluids with conductivity of upper Hashin-Shtrikman (H-S) bound can be obtained by manipulating particles into an interconnected configuration that disperses the base fluid and thus significantly enhancing the particle-fluid interfacial energy transport. Nanofluids with conductivity higher than the upper H-S bound could also be developed by manipulating the coupled transport among various transport processes, and thus the nature of heat conduction in nanofluids. While the direct contributions of ordered liquid layer and particle Brownian motion to the nanofluid conductivity are negligible, their indirect effects can be significant via their influence on the particle morphology and/or the coupled transport.

  19. Remote cooling by a novel thermal lens with anisotropic positive thermal conductivity

    Science.gov (United States)

    Sun, Fei; He, Sailing

    2017-01-01

    A novel thermal lens that can achieve a remote cooling effect is designed by transformation thermodynamics. The effective distance between the separate hot source and cold source is shortened by our shelled thermal lens without any negative thermal conductivity. Numerical simulations verify the performance of our thermal lens. Based on the effective medium theory, we also propose a practical way to realize our lens using two-layered isotropic thermal media that are both found in nature. The proposed thermal lens will have potential applications in remote temperature control and in creating other thermal illusions.

  20. Voltage tunability of thermal conductivity in ferroelectric materials

    Science.gov (United States)

    Ihlefeld, Jon; Hopkins, Patrick Edward

    2016-02-09

    A method to control thermal energy transport uses mobile coherent interfaces in nanoscale ferroelectric films to scatter phonons. The thermal conductivity can be actively tuned, simply by applying an electrical potential across the ferroelectric material and thereby altering the density of these coherent boundaries to directly impact thermal transport at room temperature and above. The invention eliminates the necessity of using moving components or poor efficiency methods to control heat transfer, enabling a means of thermal energy control at the micro- and nano-scales.

  1. Thermal conductivity measurements of particulate materials under Martian conditions

    Science.gov (United States)

    Presley, M. A.; Christensen, P. R.

    1993-01-01

    The mean particle diameter of surficial units on Mars has been approximated by applying thermal inertia determinations from the Mariner 9 Infrared Radiometer and the Viking Infrared Thermal Mapper data together with thermal conductivity measurement. Several studies have used this approximation to characterize surficial units and infer their nature and possible origin. Such interpretations are possible because previous measurements of the thermal conductivity of particulate materials have shown that particle size significantly affects thermal conductivity under martian atmospheric pressures. The transfer of thermal energy due to collisions of gas molecules is the predominant mechanism of thermal conductivity in porous systems for gas pressures above about 0.01 torr. At martian atmospheric pressures the mean free path of the gas molecules becomes greater than the effective distance over which conduction takes place between the particles. Gas particles are then more likely to collide with the solid particles than they are with each other. The average heat transfer distance between particles, which is related to particle size, shape and packing, thus determines how fast heat will flow through a particulate material.The derived one-to-one correspondence of thermal inertia to mean particle diameter implies a certain homogeneity in the materials analyzed. Yet the samples used were often characterized by fairly wide ranges of particle sizes with little information about the possible distribution of sizes within those ranges. Interpretation of thermal inertia data is further limited by the lack of data on other effects on the interparticle spacing relative to particle size, such as particle shape, bimodal or polymodal mixtures of grain sizes and formation of salt cements between grains. To address these limitations and to provide a more comprehensive set of thermal conductivities vs. particle size a linear heat source apparatus, similar to that of Cremers, was assembled to

  2. Characterization of thermal, hydraulic, and gas diffusion properties in variably saturated sand grades

    DEFF Research Database (Denmark)

    Deepagoda Thuduwe Kankanamge Kelum, Chamindu; Smits, Kathleen; Ramirez, Jamie

    2016-01-01

    transport models (thermal conductivity, saturated hydraulic conductivity, and gas diffusivity). An existing thermal conductivity model was improved to describe the distinct three-region behavior in observed thermal conductivity–water saturation relations. Applying widely used parametric models for saturated...... hydraulic conductivity and soil-gas diffusivity, we characterized porous media tortuosity in relation to grain size. Strong relations among average particle diameter, characteristic pore diameter from soil-water retention measurements, and saturated hydraulic conductivity were found. Thus, the results......Detailed characterization of partially saturated porous media is important for understanding and predicting vadose zone transport processes. While basic properties (e.g., particle- and pore-size distributions and soil-water retention) are, in general, essential prerequisites for characterizing most...

  3. Thermal and Electrical Conductivity Measurements of CDA 510 Phosphor Bronze

    Science.gov (United States)

    Tuttle, James E.; Canavan, Edgar; DiPirro, Michael

    2009-01-01

    Many cryogenic systems use electrical cables containing phosphor bronze wire. While phosphor bronze's electrical and thermal conductivity values have been published, there is significant variation among different phosphor bronze formulations. The James Webb Space Telescope (JWST) will use several phosphor bronze wire harnesses containing a specific formulation (CDA 510, annealed temper). The heat conducted into the JWST instrument stage is dominated by these harnesses, and approximately half of the harness conductance is due to the phosphor bronze wires. Since the JWST radiators are expected to just keep the instruments at their operating temperature with limited cooling margin, it is important to know the thermal conductivity of the actual alloy being used. We describe an experiment which measured the electrical and thermal conductivity of this material between 4 and 295 Kelvin.

  4. Ultralow thermal conductivity in Electrolessly Etched (EE) Silicon Nanowires

    Science.gov (United States)

    Hippalgaonkar, Kedar; Chen, Renkun; Budaev, Bair; Tang, Jinyao; Andrews, Sean; Murphy, Padraig; Mukerjee, Subroto; Moore, Joel; Yang, Peidong; Majumdar, Arun

    2009-03-01

    EE process produces single-crystalline Silicon nanowires with rough walls. We use suspended structures to directly compute the heat transfer through single nanowires. Nanowires with diameters less than the mean free path of phonons impede transport by boundary scattering. The roughness acts as a secondary scattering mechanism to further reduce phonon transport. By controlling the amount of roughness it is possible to push limits to the extent that nanowire conductance close to quanta of thermal conductance,πkB^2 T / πkB^2 T 6 . - 6 is observed. Traditionally, the lower limit of conductivity is amorphous Silicon at 1 W/mK at room temperature. The measured conductivity of our nanostructures challenges even this amorphous limit pointing towards previously unstudied mechanisms of thermal resistance. We measure thermal conductivity of ˜150nm diameter EE wires to be ˜1 W/mK.

  5. Thermal conductivity enhancement of nanofluids containing graphene nanosheets

    Science.gov (United States)

    Sen Gupta, Soujit; Manoj Siva, V.; Krishnan, Sreenath; Sreeprasad, T. S.; Singh, Pawan K.; Pradeep, T.; Das, Sarit K.

    2011-10-01

    This paper envisages a mechanism of heat conduction behind the thermal conductivity enhancement observed in graphene nanofluids. Graphene nanofluids have been prepared, characterized, and their thermal conductivity was measured using the transient hot wire method. The enhancements in thermal conductivity are substantial even at lower concentrations and are not predicted by the classical Maxwell model. The enhancement also shows strong temperature dependence which is unlike its carbon predecessors, carbon nanotube (CNT) and graphene oxide nanofluids. It is also seen that the magnitude of enhancement is in-between CNT and metallic/metal oxide nanofluids. This could be an indication that the mechanism of heat conduction is a combination of percolation in CNT and Brownian motion and micro convection effects in metallic/metal oxide nanofluids, leading to a strong proposition of a hybrid model.

  6. Thermal and tensile strength testing of thermally-conductive adhesives and carbon foam

    CERN Document Server

    Chertok, Maxwell; Irving, Michael; Neher, Christian; Shi, Mengyao; Tolfa, Kirk; Tripathi, Mani; Vinson, Yasmeen; Wang, Ruby; Zheng, Gayle

    2016-01-01

    Future collider detectors, including silicon tracking detectors planned for the High Luminosity LHC, will require components and mechanical structures providing unprecedented strength-to-mass ratios, thermal conductivity, and radiation tolerance. This paper studies carbon foam used in conjunction with thermally conductive epoxy and thermally conductive tape for such applications. Thermal conductivity and tensile strength measurements of aluminum-carbon foam-adhesive stacks are reported. Initial radiation damage tests are also presented. These results can inform bonding method choices for future tracking detectors.

  7. Multiscale Modeling of Thermal Conductivity of Polymer/Carbon Nanocomposites

    Science.gov (United States)

    Clancy, Thomas C.; Frankland, Sarah-Jane V.; Hinkley, Jeffrey A.; Gates, Thomas S.

    2010-01-01

    Molecular dynamics simulation was used to estimate the interfacial thermal (Kapitza) resistance between nanoparticles and amorphous and crystalline polymer matrices. Bulk thermal conductivities of the nanocomposites were then estimated using an established effective medium approach. To study functionalization, oligomeric ethylene-vinyl alcohol copolymers were chemically bonded to a single wall carbon nanotube. The results, in a poly(ethylene-vinyl acetate) matrix, are similar to those obtained previously for grafted linear hydrocarbon chains. To study the effect of noncovalent functionalization, two types of polyethylene matrices. -- aligned (extended-chain crystalline) vs. amorphous (random coils) were modeled. Both matrices produced the same interfacial thermal resistance values. Finally, functionalization of edges and faces of plate-like graphite nanoparticles was found to be only modestly effective in reducing the interfacial thermal resistance and improving the composite thermal conductivity

  8. Thermal Conductivity Based on Modified Laser Flash Measurement

    Science.gov (United States)

    Lin, Bochuan; Ban, Heng; Li, Chao; Scripa, Rosalia N.; Su, Ching-Hua; Lehoczky, Sandor L.

    2005-01-01

    The laser flash method is a standard method for thermal diffusivity measurement. It employs single-pulse heating of one side of a thin specimen and measures the temperature response of the other side. The thermal diffusivity of the specimen can be obtained based on a one-dimensional transient heat transfer analysis. This paper reports the development of a theory that includes a transparent reference layer with known thermal property attached to the back of sample. With the inclusion of heat conduction from the sample to the reference layer in the theoretical analysis, the thermal conductivity and thermal diffusivity of sample can be extracted from the temperature response data. Furthermore, a procedure is established to select two points from the data to calculate these properties. The uncertainty analysis indicates that this method can be used with acceptable levels of uncertainty.

  9. Thermal conductivity characteristics of dewatered sewage sludge by thermal hydrolysis reaction.

    Science.gov (United States)

    Song, Hyoung Woon; Park, Keum Joo; Han, Seong Kuk; Jung, Hee Suk

    2014-12-01

    The purpose of this study is to quantify the thermal conductivity of sewage sludge related to reaction temperature for the optimal design of a thermal hydrolysis reactor. We continuously quantified the thermal conductivity of dewatered sludge related to the reaction temperature. As the reaction temperature increased, the dewatered sludge is thermally liquefied under high temperature and pressure by the thermal hydrolysis reaction. Therefore, the bound water in the sludge cells comes out as free water, which changes the dewatered sludge from a solid phase to slurry in a liquid phase. As a result, the thermal conductivity of the sludge was more than 2.64 times lower than that of the water at 20. However, above 200, it became 0.704 W/m* degrees C, which is about 4% higher than that of water. As a result, the change in physical properties due to thermal hydrolysis appears to be an important factor for heat transfer efficiency. Implications: The thermal conductivity of dewatered sludge is an important factor the optimal design of a thermal hydrolysis reactor. The dewatered sludge is thermally liquefied under high temperature and pressure by the thermal hydrolysis reaction. The liquid phase slurry has a higher thermal conductivity than pure water.

  10. THERMAL CONDUCTIVITY OF NON-REPOSITORY LITHOSTRATIGRAPHIC LAYERS

    Energy Technology Data Exchange (ETDEWEB)

    R. JONES

    2004-10-22

    This model report addresses activities described in ''Technical Work Plan for: Near-Field Environment and Transport Thermal Properties and Analysis Reports Integration'' (BSC 2004 [DIRS 171708]). The model develops values for thermal conductivity, and its uncertainty, for the nonrepository layers of Yucca Mountain; in addition, the model provides estimates for matrix porosity and dry bulk density for the nonrepository layers. The studied lithostratigraphic units, as identified in the ''Geologic Framework Model'' (GFM 2000) (BSC 2004 [DIRS 170029]), are the Timber Mountain Group, the Tiva Canyon Tuff, the Yucca Mountain Tuff, the Pah Canyon Tuff, the Topopah Spring Tuff (excluding the repository layers), the Calico Hills Formation, the Prow Pass Tuff, the Bullfrog Tuff, and the Tram Tuff. The deepest model units of the GFM (Tund and Paleozoic) are excluded from this study because no data suitable for model input are available. The parameter estimates developed in this report are used as input to various models and calculations that simulate heat transport through the rock mass. Specifically, analysis model reports that use product output from this report are: (1) Drift-scale coupled processes (DST and TH seepage) models; (2) Drift degradation analysis; (3) Multiscale thermohydrologic model; and (4) Ventilation model and analysis report. In keeping with the methodology of the thermal conductivity model for the repository layers in ''Thermal Conductivity of the Potential Repository Horizon'' (BSC 2004 [DIRS 169854]), the Hsu et al. (1995 [DIRS 158073]) three-dimensional (3-D) cubic model (referred to herein as ''the Hsu model'') was used to represent the matrix thermal conductivity as a function of the four parameters (matrix porosity, thermal conductivity of the saturating fluid, thermal conductivity of the solid, and geometric connectivity of the solid). The Hsu model requires input data

  11. Temperature dependence of thermal conductivity of biological tissues.

    Science.gov (United States)

    Bhattacharya, A; Mahajan, R L

    2003-08-01

    In this paper, we present our experimental results on the determination of the thermal conductivity of biological tissues using a transient technique based on the principles of the cylindrical hot-wire method. A novel, 1.45 mm diameter, 50 mm long hot-wire probe was deployed. Initial measurements were made on sponge, gelatin and Styrofoam insulation to test the accuracy of the probe. Subsequent experiments conducted on sheep collagen in the range of 25 degrees C temperature. Further, these changes in the thermal conductivity were found to be reversible. However, when the tissue was heated beyond 55 degrees C, irreversible changes in thermal conductivity were observed. Similar experiments were also conducted for determining the thermal conductivity of cow liver. In this case, the irreversible effects were found to set in much later at around 90 degrees C. Below this temperature, in the range of 25 degrees C temperature. In the second part of our study, in vivo measurements were taken on the different organs of a living pig. Comparison with reported values for dead tissues shows the thermal conductivities of living organs to be higher, indicating thereby the dominant role played by blood perfusion in enhancing the net heat transfer in living tissues. The degree of enhancement is different in different organs and shows a direct dependence on the blood flow rate.

  12. Quasi-ballistic Electronic Thermal Conduction in Metal Inverse Opals.

    Science.gov (United States)

    Barako, Michael T; Sood, Aditya; Zhang, Chi; Wang, Junjie; Kodama, Takashi; Asheghi, Mehdi; Zheng, Xiaolin; Braun, Paul V; Goodson, Kenneth E

    2016-04-13

    Porous metals are used in interfacial transport applications that leverage the combination of electrical and/or thermal conductivity and the large available surface area. As nanomaterials push toward smaller pore sizes to increase the total surface area and reduce diffusion length scales, electron conduction within the metal scaffold becomes suppressed due to increased surface scattering. Here we observe the transition from diffusive to quasi-ballistic thermal conduction using metal inverse opals (IOs), which are metal films that contain a periodic arrangement of interconnected spherical pores. As the material dimensions are reduced from ∼230 nm to ∼23 nm, the thermal conductivity of copper IOs is reduced by more than 57% due to the increase in surface scattering. In contrast, nickel IOs exhibit diffusive-like conduction and have a constant thermal conductivity over this size regime. The quasi-ballistic nature of electron transport at these length scales is modeled considering the inverse opal geometry, surface scattering, and grain boundaries. Understanding the characteristics of electron conduction at the nanoscale is essential to minimizing the total resistance of porous metals for interfacial transport applications, such as the total electrical resistance of battery electrodes and the total thermal resistance of microscale heat exchangers.

  13. Thermal conductivity enhancement in thermal grease containing different CuO structures.

    Science.gov (United States)

    Yu, Wei; Zhao, Junchang; Wang, Mingzhu; Hu, Yiheng; Chen, Lifei; Xie, Huaqing

    2015-01-01

    Different cupric oxide (CuO) structures have attracted intensive interest because of their promising applications in various fields. In this study, three kinds of CuO structures, namely, CuO microdisks, CuO nanoblocks, and CuO microspheres, are synthesized by solution-based synthetic methods. The morphologies and crystal structures of these CuO structures are characterized by field-emission scanning electron microscope and X-ray diffractometer, respectively. They are used as thermal conductive fillers to prepare silicone-based thermal greases, giving rise to great enhancement in thermal conductivity. Compared with pure silicone base, the thermal conductivities of thermal greases with CuO microdisks, CuO nanoblocks, and CuO microspheres are 0.283, 0256, and 0.239 W/mK, respectively, at filler loading of 9 vol.%, which increases 139%, 116%, and 99%, respectively. These thermal greases present a slight descendent tendency in thermal conductivity at elevated temperatures. These experimental data are compared with Nan's model prediction, indicating that the shape factor has a great influence on thermal conductivity improvement of thermal greases with different CuO structures. Meanwhile, due to large aspect ratio of CuO microdisks, they can form thermal networks more effectively than the other two structures, resulting in higher thermal conductivity enhancement.

  14. Optimization of volume to point conduction problem based on a novel thermal conductivity discretization algorithm

    Institute of Scientific and Technical Information of China (English)

    Wenjing Du; Peili Wang; Lipeng Song; Lin Cheng

    2015-01-01

    A conduction heat transfer process is enhanced by filling prescribed quantity and optimized-shaped high thermal conductivity materials to the substrate. Numerical simulations and analyses are performed on a volume to point conduction problem based on the principle of minimum entropy generation. In the optimization, the arrange-ment of high thermal conductivity materials is variable, the quantity of high thermal-conductivity material is constrained, and the objective is to obtain the maximum heat conduction rate as the entropy is the minimum. A novel algorithm of thermal conductivity discretization is proposed based on large quantity of calculations. Compared with other algorithms in literature, the average temperature in the substrate by the new algorithm is lower, while the highest temperature in the substrate is in a reasonable range. Thus the new algorithm is fea-sible. The optimization of volume to point heat conduction is carried out in a rectangular model with radiation boundary condition and constant surface temperature boundary condition. The results demonstrate that the al-gorithm of thermal conductivity discretization is applicable for volume to point heat conduction problems.

  15. Atomistic Modeling of Thermal Conductivity of Epoxy Nanotube Composites

    Science.gov (United States)

    Fasanella, Nicholas A.; Sundararaghavan, Veera

    2016-05-01

    The Green-Kubo method was used to investigate the thermal conductivity as a function of temperature for epoxy/single wall carbon nanotube (SWNT) nanocomposites. An epoxy network of DGEBA-DDS was built using the `dendrimer' growth approach, and conductivity was computed by taking into account long-range Coulombic forces via a k-space approach. Thermal conductivity was calculated in the direction perpendicular to, and along the SWNT axis for functionalized and pristine SWNT/epoxy nanocomposites. Inefficient phonon transport at the ends of nanotubes is an important factor in the thermal conductivity of the nanocomposites, and for this reason discontinuous nanotubes were modeled in addition to long nanotubes. The thermal conductivity of the long, pristine SWNT/epoxy system is equivalent to that of an isolated SWNT along its axis, but there was a 27% reduction perpendicular to the nanotube axis. The functionalized, long SWNT/epoxy system had a very large increase in thermal conductivity along the nanotube axis (~700%), as well as the directions perpendicular to the nanotube (64%). The discontinuous nanotubes displayed an increased thermal conductivity along the SWNT axis compared to neat epoxy (103-115% for the pristine SWNT/epoxy, and 91-103% for functionalized SWNT/epoxy system). The functionalized system also showed a 42% improvement perpendicular to the nanotube, while the pristine SWNT/epoxy system had no improvement over epoxy. The thermal conductivity tensor is averaged over all possible orientations to see the effects of randomly orientated nanotubes, and allow for experimental comparison. Excellent agreement is seen for the discontinuous, pristine SWNT/epoxy nanocomposite. These simulations demonstrate there exists a threshold of the SWNT length where the best improvement for a composite system with randomly oriented nanotubes would transition from pristine SWNTs to functionalized SWNTs.

  16. Modified graphite filled natural rubber composites with good thermal conductivity

    Institute of Scientific and Technical Information of China (English)

    Junping Song; Lianxiang Ma; Yan He; Haiquan Yan; Zan Wu; Wei Li

    2015-01-01

    The rubber composites with good thermal conductivity contribute to heat dissipation of tires. Graphite filled natural rubber composites were developed in this study to provide good thermal conductivity. Graphite was coated with polyacrylate polymerized by monomers including methyl methacrylate, n-butyl acrylate and acrylic acid. The ratios between a filler and acrylate polymerization emulsion and those between monomers were varied. Eight types of surface modification formulas were experimentally investigated. Modification formula can affect coating results and composite properties greatly. The best coating type was achieved by a ratio of 1:1 between methyl methacrylate and n-butyl acrylate. The coating of graphite was thermal y stable in a running tire. Filled with modified graphite, the tire thermal conductivity reached up to 0.517–0.569 W·m-1·K-1. In addition, the mechanical performance was improved with increased crosslink density, extended scorch time and short vulcanization time.

  17. Determining Effective Thermal Conductivity of Fabrics by Using Fractal Method

    Science.gov (United States)

    Zhu, Fanglong; Li, Kejing

    2010-03-01

    In this article, a fractal effective thermal conductivity model for woven fabrics with multiple layers is developed. Structural models of yarn and plain woven fabric are derived based on the fractal characteristics of macro-pores (gap or channel) between the yarns and micro-pores inside the yarns. The fractal effective thermal conductivity model can be expressed as a function of the pore structure (fractal dimension) and architectural parameters of the woven fabric. Good agreement is found between the fractal model and the thermal conductivity measurements in the general porosity ranges. It is expected that the model will be helpful in the evaluation of thermal comfort for woven fabric in the whole range of porosity.

  18. Coherent thermal conductance of 1-D photonic crystals

    Energy Technology Data Exchange (ETDEWEB)

    Tschikin, Maria [Institut für Physik, Carl von Ossietzky Universität, D-26111 Oldenburg (Germany); Ben-Abdallah, Philippe [Laboratoire Charles Fabry, UMR 8501, Institut d' Optique, CNRS, Université Paris-Sud, 2, Avenue Augustin Fresnel, RD128, 91127 Palaiseau Cedex (France); Biehs, Svend-Age, E-mail: biehs@theorie.physik.uni-oldenburg.de [Institut für Physik, Carl von Ossietzky Universität, D-26111 Oldenburg (Germany)

    2012-10-01

    We present an exact calculation of coherent thermal conductance in 1-D multilayer photonic crystals using the S-matrix method. In particular, we study the thermal conductance in a bilayer structure of Si/vacuum or Al{sub 2}O{sub 3}/vacuum slabs by means of the exact radiative heat flux expression. Based on the results obtained for the Al{sub 2}O{sub 3}/vacuum structure we show by comparison with previous works that the material losses and (localized) surface modes supported by the inner layers play a fundamental role and cannot be omitted in the definition of thermal conductance. Our results could have significant implications in the conception of efficient thermal barriers.

  19. Rock thermal conductivity as key parameter for geothermal numerical models

    Science.gov (United States)

    Di Sipio, Eloisa; Chiesa, Sergio; Destro, Elisa; Galgaro, Antonio; Giaretta, Aurelio; Gola, Gianluca; Manzella, Adele

    2013-04-01

    The geothermal energy applications are undergoing a rapid development. However, there are still several challenges in the successful exploitation of geothermal energy resources. In particular, a special effort is required to characterize the thermal properties of the ground along with the implementation of efficient thermal energy transfer technologies. This paper focuses on understanding the quantitative contribution that geosciences can receive from the characterization of rock thermal conductivity. The thermal conductivity of materials is one of the main input parameters in geothermal modeling since it directly controls the steady state temperature field. An evaluation of this thermal property is required in several fields, such as Thermo-Hydro-Mechanical multiphysics analysis of frozen soils, designing ground source heat pumps plant, modeling the deep geothermal reservoirs structure, assessing the geothermal potential of subsoil. Aim of this study is to provide original rock thermal conductivity values useful for the evaluation of both low and high enthalpy resources at regional or local scale. To overcome the existing lack of thermal conductivity data of sedimentary, igneous and metamorphic rocks, a series of laboratory measurements has been performed on several samples, collected in outcrop, representative of the main lithologies of the regions included in the VIGOR Project (southern Italy). Thermal properties tests were carried out both in dry and wet conditions, using a C-Therm TCi device, operating following the Modified Transient Plane Source method.Measurements were made at standard laboratory conditions on samples both water saturated and dehydrated with a fan-forced drying oven at 70 ° C for 24 hr, for preserving the mineral assemblage and preventing the change of effective porosity. Subsequently, the samples have been stored in an air-conditioned room while bulk density, solid volume and porosity were detected. The measured thermal conductivity

  20. Size effects in molecular dynamics thermal conductivity predictions

    Science.gov (United States)

    Sellan, D. P.; Landry, E. S.; Turney, J. E.; McGaughey, A. J. H.; Amon, C. H.

    2010-06-01

    We predict the bulk thermal conductivity of Lennard-Jones argon and Stillinger-Weber silicon using the Green-Kubo (GK) and direct methods in classical molecular dynamics simulations. While system-size-independent thermal conductivities can be obtained with less than 1000 atoms for both materials using the GK method, the linear extrapolation procedure [Schelling , Phys. Rev. B 65, 144306 (2002)] must be applied to direct method results for multiple system sizes. We find that applying the linear extrapolation procedure in a manner consistent with previous researchers can lead to an underprediction of the GK thermal conductivity (e.g., by a factor of 2.5 for Stillinger-Weber silicon at a temperature of 500 K). To understand this discrepancy, we perform lattice dynamics calculations to predict phonon properties and from these, length-dependent thermal conductivities. From these results, we find that the linear extrapolation procedure is only accurate when the minimum system size used in the direct method simulations is comparable to the largest mean-free paths of the phonons that dominate the thermal transport. This condition has not typically been satisfied in previous works. To aid in future studies, we present a simple metric for determining if the system sizes used in direct method simulations are sufficiently large so that the linear extrapolation procedure can accurately predict the bulk thermal conductivity.

  1. Beating the amorphous limit in thermal conductivity by superlattices design.

    Science.gov (United States)

    Mizuno, Hideyuki; Mossa, Stefano; Barrat, Jean-Louis

    2015-09-16

    The value measured in the amorphous structure with the same chemical composition is often considered as a lower bound for the thermal conductivity of any material: the heat carriers are strongly scattered by disorder, and their lifetimes reach the minimum time scale of thermal vibrations. An appropriate design at the nano-scale, however, may allow one to reduce the thermal conductivity even below the amorphous limit. In the present contribution, using molecular-dynamics simulation and the Green-Kubo formulation, we study systematically the thermal conductivity of layered phononic materials (superlattices), by tuning different parameters that can characterize such structures. We have discovered that the key to reach a lower-than-amorphous thermal conductivity is to block almost completely the propagation of the heat carriers, the superlattice phonons. We demonstrate that a large mass difference in the two intercalated layers, or weakened interactions across the interface between layers result in materials with very low thermal conductivity, below the values of the corresponding amorphous counterparts.

  2. Robustly Engineering Thermal Conductivity of Bilayer Graphene by Interlayer Bonding.

    Science.gov (United States)

    Zhang, Xiaoliang; Gao, Yufei; Chen, Yuli; Hu, Ming

    2016-02-25

    Graphene and its bilayer structure are the two-dimensional crystalline form of carbon, whose extraordinary electron mobility and other unique features hold great promise for nanoscale electronics and photonics. Their realistic applications in emerging nanoelectronics usually call for thermal transport manipulation in a controllable and precise manner. In this paper we systematically studied the effect of interlayer covalent bonding, in particular different interlay bonding arrangement, on the thermal conductivity of bilayer graphene using equilibrium molecular dynamics simulations. It is revealed that, the thermal conductivity of randomly bonded bilayer graphene decreases monotonically with the increase of interlayer bonding density, however, for the regularly bonded bilayer graphene structure the thermal conductivity possesses unexpectedly non-monotonic dependence on the interlayer bonding density. The results suggest that the thermal conductivity of bilayer graphene depends not only on the interlayer bonding density, but also on the detailed topological configuration of the interlayer bonding. The underlying mechanism for this abnormal phenomenon is identified by means of phonon spectral energy density, participation ratio and mode weight factor analysis. The large tunability of thermal conductivity of bilayer graphene through rational interlayer bonding arrangement paves the way to achieve other desired properties for potential nanoelectronics applications involving graphene layers.

  3. Discussion on the thermal conductivity enhancement of nanofluids.

    Science.gov (United States)

    Xie, Huaqing; Yu, Wei; Li, Yang; Chen, Lifei

    2011-02-09

    Increasing interests have been paid to nanofluids because of the intriguing heat transfer enhancement performances presented by this kind of promising heat transfer media. We produced a series of nanofluids and measured their thermal conductivities. In this article, we discussed the measurements and the enhancements of the thermal conductivity of a variety of nanofluids. The base fluids used included those that are most employed heat transfer fluids, such as deionized water (DW), ethylene glycol (EG), glycerol, silicone oil, and the binary mixture of DW and EG. Various nanoparticles (NPs) involving Al2O3 NPs with different sizes, SiC NPs with different shapes, MgO NPs, ZnO NPs, SiO2 NPs, Fe3O4 NPs, TiO2 NPs, diamond NPs, and carbon nanotubes with different pretreatments were used as additives. Our findings demonstrated that the thermal conductivity enhancements of nanofluids could be influenced by multi-faceted factors including the volume fraction of the dispersed NPs, the tested temperature, the thermal conductivity of the base fluid, the size of the dispersed NPs, the pretreatment process, and the additives of the fluids. The thermal transport mechanisms in nanofluids were further discussed, and the promising approaches for optimizing the thermal conductivity of nanofluids have been proposed.

  4. An International Round-Robin Study, Part II: Thermal Diffusivity, Specific Heat and Thermal Conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Hsin [ORNL; Porter, Wallace D [ORNL; Bottner, Harold [Fraunhofer-Institute, Freiburg, Germany; Konig, Jan [Fraunhofer-Institute, Freiburg, Germany; Chen, Lidong [Chinese Academy of Sciences; Bai, Shengqiang [Chinese Academy of Sciences; Tritt, Terry M. [Clemson University; Mayolett, Alex [Corning, Inc; Senawiratne, Jayantha [Corning, Inc; Smith, Charlene [Corning, Inc; Harris, Fred [ZT-Plus; Gilbert, Partricia [Marlow Industries, Inc; Sharp, J [Marlow Industries, Inc; Lo, Jason [CANMET - Materials Technology Laboratory, Natural Resources of Canada; Keinke, Holger [University of Waterloo, Canada; Kiss, Laszlo I. [University of Quebec at Chicoutimi

    2013-01-01

    For bulk thermoelectrics, figure-of-merit, ZT, still needs to improve from the current value of 1.0 - 1.5 to above 2 to be competitive to other alternative technologies. In recent years, the most significant improvements in ZT were mainly due to successful reduction of thermal conductivity. However, thermal conductivity cannot be measured directly at high temperatures. The combined measurements of thermal diffusivity and specific heat and density are required. It has been shown that thermal conductivity is the property with the greatest uncertainty and has a direct influence on the accuracy of the figure of merit. The International Energy Agency (IEA) group under the implementing agreement for Advanced Materials for Transportation (AMT) has conducted two international round-robins since 2009. This paper is Part II of the international round-robin testing of transport properties of bulk bismuth telluride. The main focuses in Part II are on thermal diffusivity, specific heat and thermal conductivity.

  5. Performance of thermal conductivity probes for planetary applications

    Directory of Open Access Journals (Sweden)

    E. S. Hütter

    2012-01-01

    Full Text Available This work aims to contribute to the development of in situ instruments feasible for space application. Commercial as well as custom made thermal sensors, based on the transient hot wire technique and suitable for direct measurement of the effective thermal conductivity of granular media, were tested for application under airless conditions. The investigated media range from compact specimen of well known thermal conductivity used for calibration of the sensors to various granular planetary analogue materials of different shape and grain size. Measurements were performed under gas pressures ranging from 103 hPa down to about 10−5 hPa. It was found that for the inspected granular materials the given pressure decrease results in a decrease of the thermal conductivity by about two orders of magnitude. In order to check the ability of custom-made sensors to measure the thermal conductivity of planetary surface layers, detailed numerical simulations predicting the response of the different sensors have also been performed. Both, measurements and simulations, revealed that for investigations under high vacuum conditions (as they prevail e.g. on the lunar surface the derived thermal conductivity values can significantly depend on the sensor geometry, the axial heat flow and the thermal contact between probe and surrounding material. Therefore in these cases a careful calibration of each particular sensor is necessary in order to obtain reliable thermal conductivity measurements. The custom-made sensors presented in this work can serve as prototypes for payload to be flown on future planetary lander missions, in particular for airless bodies like the Moon, asteroids and comets, but also for Mars.

  6. A thermal conductivity model for U-­Si compounds

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Yongfeng [Idaho National Lab. (INL), Idaho Falls, ID (United States); Andersson, Anders David Ragnar [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-02-02

    U3Si2 is a candidate for accident tolerant nuclear fuel being developed as an alternative to UO2 in commercial light water reactors (LWRs). One of its main benefits compared to UO2 is higher thermal conductivity that increases with temperature. This increase is contrary to UO2, for which the thermal conductivity decreases with temperature. The reason for the difference is the electronic origin of thermal conductivity in U3Si2, as compared to the phonon mechanism responsible for thermal transport in UO2. The phonon thermal conductivity in UO2 is unusually low for a fluorite oxide due to the strong interaction with the spins in the paramagnetic phase. The thermal conductivity of U3Si2 as well as other U-­Si compounds has been measured experimentally [1-­4]. However, for fuel performance simulations it is also critical to model the degradation of the thermal conductivity due to damage and microstructure evolution caused by the reactor environment (irradiation and high temperature). For UO2 this reduction is substantial and it has been the topic of extensive NEAMS research resulting in several publications [5, 6]. There are no data or models for the evolution of the U3Si2 thermal conductivity under irradiation. We know that the intrinsic thermal conductivities of UO2 (semi-conductor) and U3Si2 (metal) are very different, and we do not necessarily expect the dependence on damage to be the same either, which could present another advantage for the silicide fuel. In this report we summarize the first step in developing a model for the thermal conductivity of U-­Si compounds with the goal of capturing the effect of damage in U3Si2. Next year, we will focus on lattice damage. We will also attempt to assess the impact of fission gas bubbles.

  7. Calibration of non-ideal thermal conductivity sensors

    Directory of Open Access Journals (Sweden)

    N. I. Kömle

    2012-09-01

    Full Text Available A popular method for measuring the thermal conductivity of solid materials is the transient heated needle method. It allows to evaluate the thermal conductivity of a solid or granular material to be evaluated simply by combining a temperature measurement with a well-defined electrical current flowing through a resistance wire enclosed in a long and thin needle. Standard laboratory sensors that are typically used in laboratory work consist of very thin steel needles with a large length-to-diameter ratio. This type of needles is convenient since it is mathematically easy to derive the thermal conductivity of a soft granular material from a simple temperature measurement. However, such a geometry often results in a mechanically weak sensor, which can bend or fail when inserted into a material that is harder than expected. For deploying such a sensor on a planetary surface, with often unknown soil properties, it is necessary to construct more rugged sensors. These requirements can lead to a design which differs substantially from the ideal geometry, and additional care must be taken in the calibration and data analysis. In this paper we present the performance of a prototype thermal conductivity sensor designed for planetary missions. The thermal conductivity of a suite of solid and granular materials was measured both by a standard needle sensor and by several customized sensors with non-ideal geometry. We thus obtained a calibration curve for the non-ideal sensors. The theory describing the temperature response of a sensor with such unfavorable length-to-diameter ratio is complicated and highly nonlinear. However, our measurements reveal that over a wide range of thermal conductivities there is an almost linear relationship between the result obtained by the standard sensor and the result derived from the customized, non-ideal sensors. This allows to measure thermal conductivity values for harder soils, which are not easily accessible when using

  8. Calibration of non-ideal thermal conductivity sensors

    Directory of Open Access Journals (Sweden)

    N. I. Kömle

    2013-04-01

    Full Text Available A popular method for measuring the thermal conductivity of solid materials is the transient hot needle method. It allows the thermal conductivity of a solid or granular material to be evaluated simply by combining a temperature measurement with a well-defined electrical current flowing through a resistance wire enclosed in a long and thin needle. Standard laboratory sensors that are typically used in laboratory work consist of very thin steel needles with a large length-to-diameter ratio. This type of needle is convenient since it is mathematically easy to derive the thermal conductivity of a soft granular material from a simple temperature measurement. However, such a geometry often results in a mechanically weak sensor, which can bend or fail when inserted into a material that is harder than expected. For deploying such a sensor on a planetary surface, with often unknown soil properties, it is necessary to construct more rugged sensors. These requirements can lead to a design which differs substantially from the ideal geometry, and additional care must be taken in the calibration and data analysis. In this paper we present the performance of a prototype thermal conductivity sensor designed for planetary missions. The thermal conductivity of a suite of solid and granular materials was measured both by a standard needle sensor and by several customized sensors with non-ideal geometry. We thus obtained a calibration curve for the non-ideal sensors. The theory describing the temperature response of a sensor with such unfavorable length-to-diameter ratio is complicated and highly nonlinear. However, our measurements reveal that over a wide range of thermal conductivities there is an almost linear relationship between the result obtained by the standard sensor and the result derived from the customized, non-ideal sensors. This allows for the measurement of thermal conductivity values for harder soils, which are not easily accessible when using

  9. Thermal Conductivity of Suspension of Aggregating Nanometric Rods

    Directory of Open Access Journals (Sweden)

    Amine Ammar

    2016-12-01

    Full Text Available Enhancing thermal conductivity of simple fluids is of major interest in numerous applicative systems. One possibility of enhancing thermal properties consists of dispersing small conductive particles inside. However, in general, aggregation effects occur and then one must address systems composed of dispersed clusters composed of particles as well as the ones related to percolated networks. This papers analyzes the conductivity enhancement of different microstructures scaling from clusters dispersed into a simple matrix to the ones related to percolated networks exhibiting a fractal morphology.

  10. Interfacial Thermal Conductance of Thiolate-Protected Gold Nanospheres

    CERN Document Server

    Stocker, Kelsey M; Gezelter, J Daniel

    2016-01-01

    Molecular dynamics simulations of thiolate-protected and solvated gold nanoparticles were carried out in the presence of a non-equilibrium heat flux between the solvent and the core of the particle. The interfacial thermal conductance ($G$) was computed for these interfaces, and the behavior of the thermal conductance was studied as a function of particle size, ligand flexibility, and ligand chain length. In all cases, thermal conductance of the ligand-protected particles was higher than the bare metal-solvent interface. A number of mechanisms for the enhanced conductance were investigated, including thiolate-driven corrugation of the metal surface, solvent ordering at the interface, solvent-ligand interpenetration, and ligand ordering relative to the particle surface. Only the smallest particles exhibited significant corrugation. All ligands permitted substantial solvent-ligand interpenetration, and ligand chain length has a significant influence on the orientational ordering of interfacial solvent. Solvent-...

  11. Bulk thermal conductivity of composites with spherical inclusions

    Science.gov (United States)

    Sangani, A. S.; Yao, C.

    1988-03-01

    The problem of determining the bulk or effective thermal conductivity of a two-phase composite material whose unit cells contain N(N>1) spherical particles of thermal conductivity αk suspended in a medium of thermal conductivity k has been treated by extending an earlier analysis of McPhedran and Milton [Appl. Phys. A 26, 207 (1981)] who considered the case N=1. The technique is applied to computer-generated two-phase composites with N=16 whose radial distribution functions approximately satisfy the Percus-Yevick equation. The results, which are presented for a wide range of α and φ (the volume fraction of the spheres), are shown to be in good agreement with the experimental values of conductivity of fluidized beds reported by Turner [Chem. Eng. Sci. 31, 487 (1976)].

  12. Development of Advanced Low Conductivity Thermal Barrier Coatings

    Science.gov (United States)

    Zhu, Dong-Ming; Miller, Robert A.

    2004-01-01

    Advanced multi-component, low conductivity oxide thermal barrier coatings have been developed using an approach that emphasizes real-time monitoring of thermal conductivity under conditions that are engine-like in terms of temperatures and heat fluxes. This is in contrast to the traditional approach where coatings are initially optimized in terms of furnace and burner rig durability with subsequent measurement in the as-processed or furnace-sintered condition. The present work establishes a laser high-heat-flux test as the basis for evaluating advanced plasma-sprayed and electron beam-physical vapor deposited (EB-PVD) thermal barrier coatings under the NASA Ultra-Efficient Engine Technology (UEET) Program. The candidate coating materials for this program are novel thermal barrier coatings that are found to have significantly reduced thermal conductivities and improved thermal stability due to an oxide-defect-cluster design. Critical issues for designing advanced low conductivity coatings with improved coating durability are also discussed.

  13. Performance of thermal conductivity probes for planetary applications

    Directory of Open Access Journals (Sweden)

    E. S. Hütter

    2012-05-01

    Full Text Available This work aims to contribute to the development of in situ instruments feasible for space application. Commercial as well as custom-made thermal sensors, based on the transient hot wire technique and suitable for direct measurement of the effective thermal conductivity of granular media, were tested for application under airless conditions. In order to check the ability of custom-made sensors to measure the thermal conductivity of planetary surface layers, detailed numerical simulations predicting the response of the different sensors have been performed. These simulations reveal that for investigations under high vacuum conditions (as they prevail, e.g. on the lunar surface, the derived thermal conductivity values can significantly depend on sensor geometry, axial heat flow, and the thermal contact between probe and surrounding material. Therefore, a careful calibration of each particular sensor is necessary in order to obtain reliable thermal conductivity measurements. The custom-made sensors presented in this work can serve as prototypes for payload to be flown on future planetary lander missions, in particular for airless bodies like the Moon, asteroids and comets, but also for Mars.

  14. Electro-thermal pilot in the Athabasca oil sands : theory versus performance

    Energy Technology Data Exchange (ETDEWEB)

    McGee, B.C.W. [E-T Energy, Calgary, AB (Canada)

    2008-07-01

    This paper provided details of a proof of concept test of E-T Energy's electro-thermal dynamic stripping process (ET-DSP). The technology combined features of electro-thermal heating with heat transfer by convection. Water was injected into the ends of an electrode where power density was most intense. Injected water carried heat away from the electrode into the reservoir. The tests were preceded by a mathematical model designed to quantify performance metrics including the amount of water usage for produced oil, energy input requirements, greenhouse gas (GHG) emissions, drilling performance, and operating costs. Field tests included a monitoring phase with new progressive cavity pumps (PCPs). Results of the tests and modelling studies showed that recovery factors were achieved with less energy use than thought possible. An energy oil ratio of 61.52 kWh per barrel was achieved for the production of bitumen from X05 was equivalent to a steam oil ratio of 0.49. Increases in temperature were achieved within 30 days. It was concluded that the ET-DSP process provided an efficient in situ thermal recovery technology for the production of bitumens. Recovery factors were demonstrated at 75 per cent or more. The process also provided rapid and uniform heating without the need for injection and displacing reservoir fluids. The process produced bitumens that were sand-free, with virtually no emulsions. 8 refs., 3 tabs., 10 figs.

  15. Reduction of thermal conductivity in phononic nanomesh structures

    KAUST Repository

    Yu, Jen-Kan

    2010-07-25

    Controlling the thermal conductivity of a material independently of its electrical conductivity continues to be a goal for researchers working on thermoelectric materials for use in energy applications1,2 and in the cooling of integrated circuits3. In principle, the thermal conductivity κ and the electrical conductivity σ may be independently optimized in semiconducting nanostructures because different length scales are associated with phonons (which carry heat) and electric charges (which carry current). Phonons are scattered at surfaces and interfaces, so κ generally decreases as the surface-to-volume ratio increases. In contrast, σ is less sensitive to a decrease in nanostructure size, although at sufficiently small sizes it will degrade through the scattering of charge carriers at interfaces. Here, we demonstrate an approach to independently controlling κ based on altering the phonon band structure of a semiconductor thin film through the formation of a phononic nanomesh film. These films are patterned with periodic spacings that are comparable to, or shorter than, the phonon mean free path. The nanomesh structure exhibits a substantially lower thermal conductivity than an equivalently prepared array of silicon nanowires, even though this array has a significantly higher surface-to-volume ratio. Bulk-like electrical conductivity is preserved. We suggest that this development is a step towards a coherent mechanism for lowering thermal conductivity. © 2010 Macmillan Publishers Limited. All rights reserved.

  16. Dependence of thermal conductivity of snow on microstructure

    Indian Academy of Sciences (India)

    P K Satyawali; A K Singh

    2008-08-01

    A geometrical model,including different geometrical shapes in fluencing thermal conductivity of snow is proposed.The geometrical model has been assumed to comprise of unit cells having solid (ice)inclusion as an aggregation of spherical,cylindrical or cubical shapes with vertical connection, arranged in a cubic packing.From the geometrical model and one-dimensional heat transfer theory, the effective thermal conductivity has been computed.For this purpose,coupled one-dimensional heat transfer equations have been solved for steady-state condition to account for conduction in ice, conduction in air and latent heat transfer due to water vapour sublimation through air.The model demonstrates the dependency of thermal conductivity on density,grain-spacing,grain contact ratio and temperature.Spherical inclusions give highest conductivity while cubical inclusion estimates lowest value for the same density.Thermal conductivity has been found increasing sharply near to the packing density for all three shapes.Empirical model results and results obtained from existing microstructure based models have also been compared with the present model.

  17. Divergent and Ultrahigh Thermal Conductivity in Millimeter-Long Nanotubes

    Science.gov (United States)

    Lee, Victor; Wu, Chi-Hsun; Lou, Zong-Xing; Lee, Wei-Li; Chang, Chih-Wei

    2017-03-01

    Low-dimensional materials could display anomalous thermal conduction that the thermal conductivity (κ ) diverges with increasing lengths, in ways inconceivable in any bulk materials. However, previous theoretical or experimental investigations were plagued with many finite-size effects, rendering the results either indirect or inconclusive. Indeed, investigations on the anomalous thermal conduction must demand the sample length to be sufficiently long so that the phenomena could emerge from unwanted finite-size effects. Here we report experimental observations that the κ 's of single-wall carbon nanotubes continuously increase with their lengths over 1 mm, reaching at least 8640 W /mK at room temperature. Remarkably, the anomalous thermal conduction persists even with the presence of defects, isotopic disorders, impurities, and surface absorbates. Thus, we demonstrate that the anomalous thermal conduction in real materials can persist over much longer distances than previously thought. The finding would open new regimes for wave engineering of heat as well as manipulating phonons at macroscopic scales.

  18. Review of interfacial layer's effect on thermal conductivity in nanofluid

    Science.gov (United States)

    Kotia, Ankit; Borkakoti, Sheeba; Deval, Piyush; Ghosh, Subrata Kumar

    2017-01-01

    An ordered liquid layer around the particle-liquid interface is called as interfacial layer. It has been observed that interfacial layer is an essential parameter for determining the effective thermal conductivity of nanofluids. The review attempts to summarize the prominent articles related to interfacial layer effect on the thermal conductivity of nanofluids. First section of the paper discusses about various experimental approaches used to describe the effect of interfacial layer. Second section deals with about the mathematical models and assumed values regarding the thickness of interfacial layer by several authors. A review of previous works featuring mathematical investigations and experimental approaches seem to be suggesting that, interfacial layer have dominating effect on the effective thermal conductivity of the nanofluids. Third section of the paper deals with various mathematical models available in open literature for interfacial layer thermal conductivity. In the last section, models for effective thermal conductivity of the nanofluids considering the interfacial layer and percentage deviations in the predictions of mathematical models have been discussed.

  19. On the thermal conductivity of gold nanoparticle colloids.

    Science.gov (United States)

    Shalkevich, Natallia; Escher, Werner; Bürgi, Thomas; Michel, Bruno; Si-Ahmed, Lynda; Poulikakos, Dimos

    2010-01-19

    Nanofluids (colloidal suspensions of nanoparticles) have been reported to display significantly enhanced thermal conductivities relative to those of conventional heat transfer fluids, also at low concentrations well below 1% per volume (Putnam, S. A., et at. J. Appl. Phys. 2006, 99, 084308; Liu, M.-S. L., et al. Int. J. Heat Mass Transfer. 2006, 49; Patel, H. E., et al. Appl. Phys. Lett. 2003, 83, 2931-2933). The purpose of this paper is to evaluate the effect of the particle size, concentration, stabilization method and particle clustering on the thermal conductivity of gold nanofluids. We synthesized spherical gold nanoparticles of different size (from 2 to 45 nm) and prepared stable gold colloids in the range of volume fraction of 0.00025-1%. The colloids were inspected by UV-visible spectroscopy, transmission electron microscope (TEM) and dynamic light scattering (DLS). The thermal conductivity has been measured by the transient hot-wire method (THW) and the steady state parallel plate method (GAP method). Despite a significant search in parameter space no significant anomalous enhancement of thermal conductivity was observed. The highest enhancement in thermal conductivity is 1.4% for 40 nm sized gold particles stabilized by EGMUDE (triethyleneglycolmono-11-mercaptoundecylether) and suspended in water with a particle-concentration of 0.11 vol%.

  20. Anisotropic thermal conduction with magnetic fields in galaxy clusters

    Science.gov (United States)

    Arth, Alexander; Dolag, Klaus; Beck, Alexander; Petkova, Margarita; Lesch, Harald

    2015-08-01

    Magnetic fields play an important role for the propagation and diffusion of charged particles, which are responsible for thermal conduction. In this poster, we present an implementation of thermal conduction including the anisotropic effects of magnetic fields for smoothed particle hydrodynamics (SPH). The anisotropic thermal conduction is mainly proceeding parallel to magnetic fields and suppressed perpendicular to the fields. We derive the SPH formalism for the anisotropic heat transport and solve the corresponding equation with an implicit conjugate gradient scheme. We discuss several issues of unphysical heat transport in the cases of extreme ansiotropies or unmagnetized regions and present possible numerical workarounds. We implement our algorithm into the cosmological simulation code GADGET and study its behaviour in several test cases. In general, we reproduce the analytical solutions of our idealised test problems, and obtain good results in cosmological simulations of galaxy cluster formations. Within galaxy clusters, the anisotropic conduction produces a net heat transport similar to an isotropic Spitzer conduction model with low efficiency. In contrast to isotropic conduction our new formalism allows small-scale structure in the temperature distribution to remain stable, because of their decoupling caused by magnetic field lines. Compared to observations, strong isotropic conduction leads to an oversmoothed temperature distribution within clusters, while the results obtained with anisotropic thermal conduction reproduce the observed temperature fluctuations well. A proper treatment of heat transport is crucial especially in the outskirts of clusters and also in high density regions. It's connection to the local dynamical state of the cluster also might contribute to the observed bimodal distribution of cool core and non cool core clusters. Our new scheme significantly advances the modelling of thermal conduction in numerical simulations and overall gives

  1. Thermal scale modeling of radiation-conduction-convection systems.

    Science.gov (United States)

    Shannon, R. L.

    1972-01-01

    Investigation of thermal scale modeling applied to radiation-conduction-convection systems with particular emphasis on the spacecraft cabin atmosphere/cabin wall thermal interface. The 'modified material preservation,' 'temperature preservation,' 'scaling compromises,' and 'Nusselt number preservation' scale modeling techniques and their inherent limitations and problem areas are described. The compromised scaling techniques of mass flux preservation and heat transfer coefficient preservation show promise of giving adequate thermal similitude while preserving both gas and temperature in the scale model. The use of these compromised scaling techniques was experimentally demonstrated in tests of full scale and 1/4 scale models. Correlation of test results for free and forced convection under various test conditions shows the effectiveness of these scaling techniques. It is concluded that either mass flux or heat transfer coefficient preservation may result in adequate thermal similitude depending on the system to be modeled. Heat transfer coefficient preservation should give good thermal similitude for manned spacecraft scale modeling applications.

  2. Spectral mapping of thermal conductivity through nanoscale ballistic transport.

    Science.gov (United States)

    Hu, Yongjie; Zeng, Lingping; Minnich, Austin J; Dresselhaus, Mildred S; Chen, Gang

    2015-08-01

    Controlling thermal properties is central to many applications, such as thermoelectric energy conversion and the thermal management of integrated circuits. Progress has been made over the past decade by structuring materials at different length scales, but a clear relationship between structure size and thermal properties remains to be established. The main challenge comes from the unknown intrinsic spectral distribution of energy among heat carriers. Here, we experimentally measure this spectral distribution by probing quasi-ballistic transport near nanostructured heaters down to 30 nm using ultrafast optical spectroscopy. Our approach allows us to quantify up to 95% of the total spectral contribution to thermal conductivity from all phonon modes. The measurement agrees well with multiscale and first-principles-based simulations. We further demonstrate the direct construction of mean free path distributions. Our results provide a new fundamental understanding of thermal transport and will enable materials design in a rational way to achieve high performance.

  3. Polymer Nanofibers with Outstanding Thermal Conductivity and Thermal Stability: Fundamental Linkage between Molecular Characteristics and Macroscopic Thermal Properties

    CERN Document Server

    Zhang, Teng; Luo, Tengfei

    2014-01-01

    Polymer nanofibers with high thermal conductivities and outstanding thermal stabilities are highly desirable in heat transfer-critical applications such as thermal management, heat exchangers and energy storage. In this work, we unlock the fundamental relations between the thermal conductivity and thermal stability of polymer nanofibers and their molecular characteristics by studying the temperature-induced phase transitions and thermal transport of a series of polymer nanofibers. Ten different polymer nanofibers with systematically chosen molecular structures are studied using large scale molecular dynamics simulations. We found that high thermal conductivity and good thermal stability can be achieved in polymers with rigid backbones, exemplified by {\\pi}-conjugated polymers, due to suppressed segmental rotations and large phonon group velocities. The low probability of segmental rotation does not only prevent temperature-induced phase transition but also enables long phonon mean free paths due to reduced di...

  4. A PC- Based Transient Method for Thermal Conductivity Measurement.

    Directory of Open Access Journals (Sweden)

    A.K. Singh

    2000-10-01

    Full Text Available In this paper, an indigenously developed thermal probe has been interfaced with a PC for automated measurement of thermal conductivity (K . The developed system has been calibrated and standardised by measuring K of glycerol. The maximum percentage error, for repeated sets of observations, was within 7.29 per cent of standard value reported for glycerol. This methodology has been successfully employed for measuring K of propellant oxidisers, additives, binders, etc.

  5. Inverse transient heat conduction problems and identification of thermal parameters

    Science.gov (United States)

    Atchonouglo, K.; Banna, M.; Vallée, C.; Dupré, J.-C.

    2008-04-01

    This work deals with the estimation of polymers properties. An inverse analysis based on finite element method is applied to identify simultaneously the constants thermal conductivity and heat capacity per unit volume. The inverse method algorithm constructed is validated from simulated transient temperature recording taken at several locations on the surface of the solid. Transient temperature measures taped with infrared camera on polymers were used for identifying the thermal properties. The results show an excellent agreement between manufacturer and identified values.

  6. Thermal computations for electronics conductive, radiative, and convective air cooling

    CERN Document Server

    Ellison, Gordon

    2010-01-01

    IntroductionPrimary mechanisms of heat flowConductionApplication example: Silicon chip resistance calculationConvectionApplication example: Chassis panel cooled by natural convectionRadiationApplication example: Chassis panel cooled only by radiation 7Illustrative example: Simple thermal network model for a heat sinked power transistorIllustrative example: Thermal network circuit for a printed circuit boardCompact component modelsIllustrative example: Pressure and thermal circuits for a forced air cooled enclosureIllustrative example: A single chip package on a printed circuit board-the proble

  7. Dynamic Measurements of the Thermal Conductivity of Insulators

    Science.gov (United States)

    Bezjak, Mladen; Zvizdić, Davor

    2011-08-01

    Measurements of the thermal conductivity of insulators that are commonly used in civil engineering are as a rule performed using Pönsgen's guarded hot-plate method under steady-state conditions. Achieving these steady-state conditions is a time consuming and relatively expensive procedure. Therefore, the application of a method that is less time consuming and less costly to common building insulating materials is of interest. The method should also have the accuracy and repeatability comparable to that of presently used methods. One such method is the transient hot-wire method (predominantly used for liquids, non-Newtonian fluids, plastics, semi-plastics, and similar materials), a dynamic method that uses a very thin pure platinum wire that functions as a thermal source in combination with a temperature sensor that detects temperature transients. This article describes the application of the transient hot-wire method to most commonly used building thermal insulating materials. The transient hot-wire measurements of the thermal conductivity were performed on many building material samples. For the sake of comparison, the thermal conductivity of samples made from the same materials was also tested using the stationary Pönsgen's guarded hot-plate method. This article describes the comparison and evaluation of the measurement results obtained from both methods as well as the estimation of pertinent measurement uncertainties. The results are presented in graphical and numerical form in tables and diagrams for each type of thermal insulator.

  8. Toward lithium ion batteries with enhanced thermal conductivity.

    Science.gov (United States)

    Koo, Bonil; Goli, Pradyumna; Sumant, Anirudha V; dos Santos Claro, Paula Cecilia; Rajh, Tijana; Johnson, Christopher S; Balandin, Alexander A; Shevchenko, Elena V

    2014-07-22

    As batteries become more powerful and utilized in diverse applications, thermal management becomes one of the central problems in their application. We report the results on thermal properties of a set of different Li-ion battery electrodes enhanced with multiwalled carbon nanotubes. Our measurements reveal that the highest in-plane and cross-plane thermal conductivities achieved in the carbon-nanotube-enhanced electrodes reached up to 141 and 3.6 W/mK, respectively. The values for in-plane thermal conductivity are up to 2 orders of magnitude higher than those for conventional electrodes based on carbon black. The electrodes were synthesized via an inexpensive scalable filtration method, and we demonstrate that our approach can be extended to commercial electrode-active materials. The best performing electrodes contained a layer of γ-Fe2O3 nanoparticles on carbon nanotubes sandwiched between two layers of carbon nanotubes and had in-plane and cross-plane thermal conductivities of ∼50 and 3 W/mK, respectively, at room temperature. The obtained results are important for thermal management in Li-ion and other high-power-density batteries.

  9. Pulse accumulation, radial heat conduction, and anisotropic thermal conductivity in pump-probe transient thermoreflectance.

    Science.gov (United States)

    Schmidt, Aaron J; Chen, Xiaoyuan; Chen, Gang

    2008-11-01

    The relationship between pulse accumulation and radial heat conduction in pump-probe transient thermoreflectance (TTR) is explored. The results illustrate how pulse accumulation allows TTR to probe two thermal length scales simultaneously. In addition, the conditions under which radial transport effects are important are described. An analytical solution for anisotropic heat flow in layered structures is given, and a method for measuring both cross-plane and in-plane thermal conductivities of thermally anisotropic thin films is described. As verification, the technique is used to extract the cross-plane and in-plane thermal conductivities of highly ordered pyrolytic graphite. Results are found to be in good agreement with literature values.

  10. On thermal conductivity of gas mixtures containing hydrogen

    Science.gov (United States)

    Zhukov, Victor P.; Pätz, Markus

    2016-12-01

    A brief review of formulas used for the thermal conductivity of gas mixtures in CFD simulations of rocket combustion chambers is carried out in the present work. In most cases, the transport properties of mixtures are calculated from the properties of individual components using special mixing rules. The analysis of different mixing rules starts from basic equations and ends by very complex semi-empirical expressions. The formulas for the thermal conductivity are taken for the analysis from the works on modelling of rocket combustion chambers. H_2- O_2 mixtures are chosen for the evaluation of the accuracy of the considered mixing rules. The analysis shows that two of them, of Mathur et al. (Mol Phys 12(6):569-579, 1967), and of Mason and Saxena (Phys Fluids 1(5):361-369, 1958), have better agreement with the experimental data than other equations for the thermal conductivity of multicomponent gas mixtures.

  11. Effective Thermal Conductivity of Insulating Material made from Recycled Newspapers

    Science.gov (United States)

    Yamada, Etsuro; Takahashi, Kaneko; Sato, Mitsuo; Ishii, Yukihiro

    In this paper, the experimental results are represented on the effective thermal conductivity of cellulose insulation powder which is made from recycled newspapers. This insulating material is useful for energy and resources saving. The steady state cylindrical absolute method is employed by considering the accuracy of measurement. The experimental results are compared with the ones measured previously by other methods. The main results obtained are as follows (1) The effective thermal conductivity of this insulating material increases with increasing temperature and effective specific density, respectively. But, these increasing rate is not so large. (2) The effective thermal conductivity is about 0.04-0.06[W/mK] at the range of the effective specific density less than 100 [kg/m3]. This value is comparable with other industrial insulating materials.

  12. Cosmological MHD simulations of cluster formation with anisotropic thermal conduction

    CERN Document Server

    Ruszkowski, M; Bruggen, M; Parrish, I; Oh, S Peng

    2010-01-01

    (abridged) The ICM has been suggested to be buoyantly unstable in the presence of magnetic field and anisotropic thermal conduction. We perform first cosmological simulations of galaxy cluster formation that simultaneously include magnetic fields, radiative cooling and anisotropic thermal conduction. In isolated and idealized cluster models, the magnetothermal instability (MTI) tends to reorient the magnetic fields radially. Using cosmological simulations of the Santa Barbara cluster we detect radial bias in the velocity and magnetic fields. Such radial bias is consistent with either the inhomogeneous radial gas flows due to substructures or residual MTI-driven field rearangements that are expected even in the presence of turbulence. Although disentangling the two scenarios is challenging, we do not detect excess bias in the runs that include anisotropic thermal conduction. The anisotropy effect is potentially detectable via radio polarization measurements with LOFAR and SKA and future X-ray spectroscopic stu...

  13. Thermal conductivity measurement of thin films by a dc method.

    Science.gov (United States)

    Yang, Junyou; Zhang, Jiansheng; Zhang, Hui; Zhu, Yunfeng

    2010-11-01

    A dc method, which needs no complex numerical calculation and expensive hardware configuration, was developed to measure the cross-plane thermal conductivity of thin films in this paper. Two parallel metallic heaters, which were deposited on different parts of the sample, serve simultaneously as the heaters and temperature sensors during the measurement. A direct current was flowed through the same two metallic strips to heat the thin-film sample. The heating power and the heater's temperature were obtained by a data acquisition device, and the thermal conductivity of thin film was calculated. To verify the validity of the dc method, several SiO(2) films with different thicknesses were deposited on Si wafers, respectively, and their thermal conductivities were measured by both the dc method and 3ω method. The results of two methods are in good agreement within an acceptable error, and they are also inconsistent with some of previously published data.

  14. Thermal conductivity of bulk and monolayer MoS 2

    KAUST Repository

    Gandi, Appala

    2016-02-26

    © Copyright EPLA, 2016. We show that the lattice contribution to the thermal conductivity of MoS2 strongly dominates the carrier contribution in a broad temperature range from 300 to 800 K. Since theoretical insight into the lattice contribution is largely missing, though it would be essential for materials design, we solve the Boltzmann transport equation for the phonons self-consistently in order to evaluate the phonon lifetimes. In addition, the length scale for transition between diffusive and ballistic transport is determined. The low out-of-plane thermal conductivity of bulk MoS2 (2.3 Wm-1K-1 at 300 K) is useful for thermoelectric applications. On the other hand, the thermal conductivity of monolayer MoS2 (131 Wm-1K-1 at 300 K) is comparable to that of Si.

  15. Thermal conductivities of some novel nonlinear optical materials.

    Science.gov (United States)

    Beasley, J D

    1994-02-20

    Results of thermal conductivity measurements are reported for several of the more recently developed nonlinear optical crystals. New or substantially revised values of thermal conductivity were obtained in six materials. Notable thermal conductivities measured were those for AgGaS(2) [0.014 W/(cm K) and 0.015 W/(cm K)], AgGaSe(2) [0.010 W/(cm K) and 0.011 W/(cm K)], beta barium borate [0.016 W/(cm K) and 0.012 W/(cm K)], and ZnGeP(2) [0.36 W/(cm K) and 0.35 W/(cm K)], with values quoted for directions respectively parallel and perpendicular to the optic axis for each material. These new data provide necessary input for the design of high-power optical frequency converters.

  16. Increased Thermal Conductivity in Metal-Organic Heat Carrier Nanofluids

    Science.gov (United States)

    Nandasiri, Manjula I.; Liu, Jian; McGrail, B. Peter; Jenks, Jeromy; Schaef, Herbert T.; Shutthanandan, Vaithiyalingam; Nie, Zimin; Martin, Paul F.; Nune, Satish K.

    2016-06-01

    Metal-organic heat carriers (MOHCs) are recently developed nanofluids containing metal-organic framework (MOF) nanoparticles dispersed in various base fluids including refrigerants (R245Fa) and methanol. Here, we report the synthesis and characterization of MOHCs containing nanoMIL-101(Cr) and graphene oxide (GO) in an effort to improve the thermo-physical properties of various base fluids. MOHC/GO nanocomposites showed enhanced surface area, porosity, and nitrogen adsorption compared with the intrinsic nanoMIL-101(Cr) and the properties depended on the amount of GO added. MIL-101(Cr)/GO in methanol exhibited a significant increase in the thermal conductivity (by approximately 50%) relative to that of the intrinsic nanoMIL-101(Cr) in methanol. The thermal conductivity of the base fluid (methanol) was increased by about 20%. The increase in the thermal conductivity of nanoMIL-101(Cr) MOHCs due to GO functionalization is explained using a classical Maxwell model.

  17. Increased Thermal Conductivity in Metal-Organic Heat Carrier Nanofluids.

    Science.gov (United States)

    Nandasiri, Manjula I; Liu, Jian; McGrail, B Peter; Jenks, Jeromy; Schaef, Herbert T; Shutthanandan, Vaithiyalingam; Nie, Zimin; Martin, Paul F; Nune, Satish K

    2016-06-15

    Metal-organic heat carriers (MOHCs) are recently developed nanofluids containing metal-organic framework (MOF) nanoparticles dispersed in various base fluids including refrigerants (R245Fa) and methanol. Here, we report the synthesis and characterization of MOHCs containing nanoMIL-101(Cr) and graphene oxide (GO) in an effort to improve the thermo-physical properties of various base fluids. MOHC/GO nanocomposites showed enhanced surface area, porosity, and nitrogen adsorption compared with the intrinsic nanoMIL-101(Cr) and the properties depended on the amount of GO added. MIL-101(Cr)/GO in methanol exhibited a significant increase in the thermal conductivity (by approximately 50%) relative to that of the intrinsic nanoMIL-101(Cr) in methanol. The thermal conductivity of the base fluid (methanol) was increased by about 20%. The increase in the thermal conductivity of nanoMIL-101(Cr) MOHCs due to GO functionalization is explained using a classical Maxwell model.

  18. Dynamical thermal conductivity of the spin Lieb lattice

    Science.gov (United States)

    Yarmohammadi, Mohsen

    2016-05-01

    In the ferromagnetic insulator with the Dzyaloshinskii-Moriya interaction (DMI), we have theoretically investigated the dynamical thermal conductivity (DTC). In other words, we have investigated the frequency dependence of thermal conductivity, κ, of the Lieb lattice, a face-centered square lattice, subjected to a time dependence temperature gradient. Using linear response theory and Green's function approach, DTC has been obtained in the context of Heisenberg Hamiltonian. At low frequencies, DTC is found to be monotonically increasing with DMI strength (DMIS), temperature and next-nearest-neighbor (NNN) coupling. Also we have found that DTC includes a peak for different values of temperature, DMIS and NNN coupling. Furthermore we study the temperature dependence of thermal conductivity of Lieb lattice for different values of DMIS, NNN coupling and external magnetic filed. We witness a decrease in DTC with temperature due to the quantum effects in the system.

  19. Thermal conductivity at a disordered quantum critical point

    CERN Document Server

    Hartnoll, Sean A; Santos, Jorge E

    2015-01-01

    Strongly disordered and strongly interacting quantum critical points are difficult to access with conventional field theoretic methods. They are, however, both experimentally important and theoretically interesting. In particular, they are expected to realize universal incoherent transport. Such disordered quantum critical theories have recently been constructed holographically by deforming a CFT by marginally relevant disorder. In this paper we find additional disordered fixed points via relevant disordered deformations of a holographic CFT. Using recently developed methods in holographic transport, we characterize the thermal conductivity in both sets of theories in 1+1 dimensions. The thermal conductivity is found to tend to a constant at low temperatures in one class of fixed points, and to scale as $T^{0.3}$ in the other. Furthermore, in all cases the thermal conductivity exhibits discrete scale invariance, with logarithmic in temperature oscillations superimposed on the low temperature scaling behavior....

  20. On thermal conductivity of gas mixtures containing hydrogen

    Science.gov (United States)

    Zhukov, Victor P.; Pätz, Markus

    2017-06-01

    A brief review of formulas used for the thermal conductivity of gas mixtures in CFD simulations of rocket combustion chambers is carried out in the present work. In most cases, the transport properties of mixtures are calculated from the properties of individual components using special mixing rules. The analysis of different mixing rules starts from basic equations and ends by very complex semi-empirical expressions. The formulas for the thermal conductivity are taken for the analysis from the works on modelling of rocket combustion chambers. \\hbox {H}_2{-}\\hbox {O}_2 mixtures are chosen for the evaluation of the accuracy of the considered mixing rules. The analysis shows that two of them, of Mathur et al. (Mol Phys 12(6):569-579, 1967), and of Mason and Saxena (Phys Fluids 1(5):361-369, 1958), have better agreement with the experimental data than other equations for the thermal conductivity of multicomponent gas mixtures.

  1. Reduction of thermal conductivity by nanoscale 3D phononic crystal.

    Science.gov (United States)

    Yang, Lina; Yang, Nuo; Li, Baowen

    2013-01-01

    We studied how the period length and the mass ratio affect the thermal conductivity of isotopic nanoscale three-dimensional (3D) phononic crystal of Si. Simulation results by equilibrium molecular dynamics show isotopic nanoscale 3D phononic crystals can significantly reduce the thermal conductivity of bulk Si at high temperature (1000 K), which leads to a larger ZT than unity. The thermal conductivity decreases as the period length and mass ratio increases. The phonon dispersion curves show an obvious decrease of group velocities in 3D phononic crystals. The phonon's localization and band gap is also clearly observed in spectra of normalized inverse participation ratio in nanoscale 3D phononic crystal.

  2. Aqueous Solution Thermal Conductivity of Beryllium-Subgroup Metal Chlorides

    Directory of Open Access Journals (Sweden)

    K. Abdullayev

    2013-01-01

    Full Text Available The paper presents experimental data on thermal conductivity of BeCl2 and SrCl2 salt aqueous solutions in the temperature range from 20 to 300 °С  and at various electrolyte concentrations  in mass percent. For the first time thermal conductivity of the system Н2О + BeCl2 has been investigated at high temperatures.The experimental results are described with the help of an empirical equation in the form of: λs = λo (1+ Am + Bm3/2 + Cm2,where λs  and λo – thermal conductivity coefficients of solution and water; A, B and C – coefficients depending on electrolyte nature; m – molality in units mol/kg.The formula error is less than  ±1 %.

  3. Anisotropic thermal conduction in galaxy clusters with MHD in Gadget

    CERN Document Server

    Arth, Alexander; Beck, Alexander M; Petkova, Margarita; Lesch, Harald

    2014-01-01

    We present an implementation of thermal conduction including the anisotropic effects of magnetic fields for SPH. The anisotropic thermal conduction is mainly proceeding parallel to magnetic fields and suppressed perpendicular to the fields. We derive the SPH formalism for the anisotropic heat transport and solve the corresponding equation with an implicit conjugate gradient scheme. We discuss several issues of unphysical heat transport in the cases of extreme ansiotropies or unmagnetized regions and present possible numerical workarounds. We implement our algorithm into the GADGET code and study its behaviour in several test cases. In general, we reproduce the analytical solutions of our idealised test problems, and obtain good results in cosmological simulations of galaxy cluster formations. Within galaxy clusters, the anisotropic conduction produces a net heat transport similar to an isotropic Spitzer conduction model with an efficiency of one per cent. In contrast to isotropic conduction our new formalism ...

  4. A new method using evaporation for high-resolution measurements of soil thermal conductivity at changing water contents

    Science.gov (United States)

    Markert, A.; Trinks, S.; Facklam, M.; Wessolek, G.

    2012-04-01

    The thermal conductivity of soils is a key parameter to know if their use as heat source or sink is planned. It is required to calculate the efficiency of ground-source heat pump systems in combination with soil heat exchangers. Apart from geothermal energy, soil thermal conductivity is essential to estimate the ampacity for buried power cables. The effective thermal conductivity of saturated and unsaturated soils, as a function of water transport, water vapour transport and heat conduction, mainly depends on the soil water content, its bulk density and texture. The major objectives of this study are (i) to describe the thermal conductivity of soil samples with a non-steady state measurement at changing water contents and for different bulk densities. Based on that it is (ii) tested if available soil thermal conductivity models are able to describe the measured data for the whole range of water contents. The new method allows a continuous measurement of thermal conductivity for soil from full water saturation to air-dryness. Thermal conductivity is measured with a thermal needle probe in predefined time intervals while the change of water content is controlled by evaporation. To relate the measured thermal conductivity to the current volumetric water content, the decrease in weight of the sample, due to evaporation, is logged with a lab scale. Soil texture of the 11 soil substrates tested in this study range between coarse sand and silty clay. To evaluate the impact of the bulk density on heat transport processes, thermal conductivity at 20°C was measured at 1.5g/cm3; 1.7g/cm3 and 1.9g/cm3 for each soil substrate. The results correspond well to literature values used to describe heat transport in soils. Due to the high-resolution and non-destructive measurements, the specific effects of the soil texture and bulk density on thermal conductivity could be proved. Decreasing water contents resulted in a non-linear decline of the thermal conductivity for all samples

  5. Comparative study of thermal conductivity in crystalline and amorphous nanocomposite

    Science.gov (United States)

    Juangsa, Firman Bagja; Muroya, Yoshiki; Ryu, Meguya; Morikawa, Junko; Nozaki, Tomohiro

    2017-06-01

    Silicon nanocrystals (SiNCs)/polystyrene (PS) nanocomposite has been observed to have a significant decrease in thermal conductivity in terms of the SiNC fraction with unspecified factors remained unclear. In this paper, amorphous silicon nanoparticles (a-SiNPs) with a mean diameter of 6 nm and PS nanocomposites were synthesized, and their thermal conductivity, including the density and specific heat, was compared with our previous work which investigated well-crystalized SiNPs (6 nm) and PS nanocomposite. The difference between amorphous and crystalline structure is insignificant, but phonon scattering at SiNPs and PS boundary is the key influencing factor of thermal conductivity reduction. The effective thermal conductivity models for nanocomposite revealed that the thermal boundary resistance, explained by Kapitza principle, is estimated to be 4 × 10-7 m2K/W, showing the significant effect of nanostructured heterogenic surface resistance on overall heat transfer behavior. Preservation of unique properties nanoscale materials and low-cost fabrication by silicon inks process at room temperature give the promising potential of SiNPs based heat transfer management.

  6. High thermal conductivity of chain-oriented amorphous polythiophene.

    Science.gov (United States)

    Singh, Virendra; Bougher, Thomas L; Weathers, Annie; Cai, Ye; Bi, Kedong; Pettes, Michael T; McMenamin, Sally A; Lv, Wei; Resler, Daniel P; Gattuso, Todd R; Altman, David H; Sandhage, Kenneth H; Shi, Li; Henry, Asegun; Cola, Baratunde A

    2014-05-01

    Polymers are usually considered thermal insulators, because the amorphous arrangement of the molecular chains reduces the mean free path of heat-conducting phonons. The most common method to increase thermal conductivity is to draw polymeric fibres, which increases chain alignment and crystallinity, but creates a material that currently has limited thermal applications. Here we show that pure polythiophene nanofibres can have a thermal conductivity up to ∼ 4.4 W m(-1) K(-1) (more than 20 times higher than the bulk polymer value) while remaining amorphous. This enhancement results from significant molecular chain orientation along the fibre axis that is obtained during electropolymerization using nanoscale templates. Thermal conductivity data suggest that, unlike in drawn crystalline fibres, in our fibres the dominant phonon-scattering process at room temperature is still related to structural disorder. Using vertically aligned arrays of nanofibres, we demonstrate effective heat transfer at critical contacts in electronic devices operating under high-power conditions at 200 °C over numerous cycles.

  7. A transient divided-bar method for simultaneous measurements of thermal conductivity and thermal diffusivity

    DEFF Research Database (Denmark)

    Bording, Thue Sylvester; Nielsen, Søren Bom; Balling, Niels

    2016-01-01

    Accurate information on thermal conductivity and thermal diffusivity of materials is of central importance in relation to geoscience and engineering problems involving the transfer of heat. Within the geosciences, this applies to all aspects regarding the determination of terrestrial heat flow...... and volumetric heat capacity, and thereby also thermal diffusivity, are measured simultaneously. As the density of samples is easily determined independently, specific heat capacity may also be determined. Finite element formulation provides a flexible forward solution for heat transfer across the bar...... and subsurface temperature modelling. Several methods, including the classical divided-bar technique, are available for laboratory measurements of thermal conductivity, and much fewer for thermal diffusivity. We have generalized the divided-bar technique to the transient case, in which thermal conductivity...

  8. A transient divided-bar method for simultaneous measurements of thermal conductivity and thermal diffusivity

    DEFF Research Database (Denmark)

    Bording, Thue Sylvester; Nielsen, Søren Bom; Balling, Niels

    2016-01-01

    Accurate information on thermal conductivity and thermal diffusivity of materials is of central importance in relation to geoscience and engineering problems involving the transfer of heat. Within the geosciences, this applies to all aspects regarding the determination of terrestrial heat flow...... and subsurface temperature modelling. Several methods, including the classical divided-bar technique, are available for laboratory measurements of thermal conductivity, and much fewer for thermal diffusivity. We have generalized the divided-bar technique to the transient case, in which thermal conductivity...... and volumetric heat capacity, and thereby also thermal diffusivity, are measured simultaneously. As the density of samples is easily determined independently, specific heat capacity may also be determined. Finite element formulation provides a flexible forward solution for heat transfer across the bar...

  9. Thermal Conductivity and Heat Transfer Coefficient of Concrete

    Institute of Scientific and Technical Information of China (English)

    GUO Lixia; GUO Lei; ZHONG Ling; ZHU Yueming

    2011-01-01

    A very simple model for predicting thermal conductivity based on its definiensis was presented.The thermal conductivity obtained using the model provided a good coincidence to the investigations performed by other authors.The heat transfer coefficient was determined by inverse analysis using the temperature measurements.From experimental results,it is noted that heat transfer coefficient increases with the increase of wind velocity and relative humidity,a prediction equation on heat transfer coefficient about wind velocity and relative humidity is given.

  10. Experimental Investigation of Thermal Conductivity of Meat During Freezing

    Science.gov (United States)

    Shinbayeva, A.; Arkharov, I.; Aldiyarov, A.; Drobyshev, A.; Zhubaniyazova, M.; Kurnosov, V.

    2017-04-01

    The cryogenic technologies of processing and storage of agricultural products are becoming increasingly indispensable in the food industry as an important factor of ensuring food safety. One of such technologies is the shock freezing of meat, which provides a higher degree of preservation of the quality of frozen products in comparison with traditional technologies. The thermal conductivity of meat is an important parameter influencing the energy consumption in the freezing process. This paper presents the results of an experimental investigation of the temperature dependence of the thermal conductivity of beef. The measurements were taken by using a specially designed measurement cell, which allows covering the temperature range from 80 to 300 K.

  11. A micro-convection model for thermal conductivity of nanofluids

    Indian Academy of Sciences (India)

    Hrishikesh E Patel; T Sundararajan; T Pradeep; A Dasgupta; N Dasgupta; Sarit K Das

    2005-11-01

    Increase in the specific surface area as well as Brownian motion are supposed to be the most significant reasons for the anomalous enhancement in thermal conductivity of nanofluids. This work presents a semi-empirical approach for the same by emphasizing the above two effects through micro-convection. A new way of modeling thermal conductivity of nanofluids has been explored which is found to agree excellently with a wide range of experimental data obtained by the present authors as well as the data published in literature.

  12. Measurement of in-plane thermal conductivity in polymer films

    OpenAIRE

    Qingshuo Wei; Chinatsu Uehara; Masakazu Mukaida; Kazuhiro Kirihara; Takao Ishida

    2016-01-01

    Measuring the in-plane thermal conductivity of organic thermoelectric materials is challenging but is critically important. Here, a method to study the in-plane thermal conductivity of free-standing films (via the use of commercial equipment) based on temperature wave analysis is explored in depth. This subject method required a free-standing thin film with a thickness larger than 10 μm and an area larger than 1 cm2, which are not difficult to obtain for most solution-processable organic ther...

  13. Low-temperature thermal conductivity of Nylon-6/Cu nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Martelli, V., E-mail: martelliv@fi.infn.i [INFN, Section of Florence, Via G. Sansone 1, 50019 Sesto Fiorentino, Florence (Italy); LENS, University of Florence, Via Nello Carrara 1, 50019 Sesto Fiorentino (Italy); Toccafondi, N. [Department of Chemistry - CSGI, University of Florence, Via Lastruccia 3, 50019 Sesto Fiorentino, Florence (Italy); Ventura, G. [INFN, Section of Florence, Via G. Sansone 1, 50019 Sesto Fiorentino, Florence (Italy); Department of Physics, University of Florence, Via G. Sansone 1, 50019 Sesto Fiorentino, Florence (Italy)

    2010-10-15

    We have produced a new nanocomposite material made up of a Nylon-6 matrix in which metallic copper nanoparticle (5% in weight) are uniformly dispersed. Here we report about the measurement of the thermal conductivity of such material between 0.1 and 30 K. Thermal conductivity of the nanocomposite does not substantially differ from that of Nylon. Nevertheless data show interesting features, in particular a sharp dip at 1.4 K which can be interpreted as a resonant scattering of phonons by copper nanoparticles.

  14. Estimating thermal diffusivity and specific heat from needle probe thermal conductivity data

    Science.gov (United States)

    Waite, W.F.; Gilbert, L.Y.; Winters, W.J.; Mason, D.H.

    2006-01-01

    Thermal diffusivity and specific heat can be estimated from thermal conductivity measurements made using a standard needle probe and a suitably high data acquisition rate. Thermal properties are calculated from the measured temperature change in a sample subjected to heating by a needle probe. Accurate thermal conductivity measurements are obtained from a linear fit to many tens or hundreds of temperature change data points. In contrast, thermal diffusivity calculations require a nonlinear fit to the measured temperature change occurring in the first few tenths of a second of the measurement, resulting in a lower accuracy than that obtained for thermal conductivity. Specific heat is calculated from the ratio of thermal conductivity to diffusivity, and thus can have an uncertainty no better than that of the diffusivity estimate. Our thermal conductivity measurements of ice Ih and of tetrahydrofuran (THF) hydrate, made using a 1.6 mm outer diameter needle probe and a data acquisition rate of 18.2 pointss, agree with published results. Our thermal diffusivity and specific heat results reproduce published results within 25% for ice Ih and 3% for THF hydrate. ?? 2006 American Institute of Physics.

  15. The effect of thermal aging on the thermal conductivity of plasma sprayed and EB-PVD thermal barrier coatings

    Energy Technology Data Exchange (ETDEWEB)

    Dinwiddie, R.B.; Beecher, S.C.; Porter, W.D. [Oak Ridge National Lab., TN (United States); Nagaraj, B.A. [General Electric Co., Cincinnati, OH (United States). Aircraft Engine Group

    1996-05-01

    Thermal barrier coatings (TBCs) applied to the hot gas components of turbine engines lead to enhanced fuel efficiency and component reliability. Understanding the mechanisms which control the thermal transport behavior of the TBCs is of primary importance. Electron beam-physical vapor deposition (EV-PVD) and air plasma spraying (APS) are the two most commonly used coating techniques. These techniques produce coatings with unique microstructures which control their performance and stability. The density of the APS coatings was controlled by varying the spray parameters. The low density APS yttria-partially stabilized zirconia (yttria-PSZ) coatings yielded a thermal conductivity that is lower than both the high density APS coatings and the EB-PVD coatings. The thermal aging of both fully and partially stabilized zirconia are compared. The thermal conductivity of the coatings permanently increases upon exposure to high temperatures. These increases are attributed to microstructural changes within the coatings. This increase in thermal conductivity can be modeled using a relationship which depends on both the temperature and time of exposure. Although the EB-PVD coatings are less susceptible to thermal aging effects, results suggest that they typically have a higher thermal conductivity than APS coatings before thermal aging. The increases in thermal conductivity due to thermal aging for plasma sprayed partially stabilized zirconia have been found to be less than for plasma sprayed fully stabilized zirconia coatings.

  16. Thermal conduction in a mirror-unstable plasma

    Science.gov (United States)

    Komarov, S. V.; Churazov, E. M.; Kunz, M. W.; Schekochihin, A. A.

    2016-07-01

    The plasma of galaxy clusters is subject to firehose and mirror instabilities at scales of order the ion Larmor radius. The mirror instability generates fluctuations of magnetic-field strength δB/B ˜ 1. These fluctuations act as magnetic traps for the heat-conducting electrons, suppressing their transport. We calculate the effective parallel thermal conductivity in the ICM in the presence of the mirror fluctuations for different stages of the evolution of the instability. The mirror fluctuations are limited in amplitude by the maximum and minimum values of the field strength, with no large deviations from the mean value. This key property leads to a finite suppression of thermal conduction at large scales. We find suppression down to ≈0.2 of the Spitzer value for the secular phase of the perturbations' growth, and ≈0.3 for their saturated phase. The effect operates in addition to other suppression mechanisms and independently of them. Globally, fluctuations δB/B ˜ 1 can be present on much larger scales, of the order of the scale of turbulent motions. However, we do not expect large suppression of thermal conduction by these, because their scale is considerably larger than the collisional mean free path of the ICM electrons. The obtained suppression of thermal conduction by a factor of ˜5 appears to be characteristic and potentially universal for a weakly collisional mirror-unstable plasma.

  17. Reduction in thermal conductivity of BiSbTe lump

    Science.gov (United States)

    Ahmad, Kaleem; Wan, C.; Al-Eshaikh, M. A.; Kadachi, A. N.

    2017-03-01

    In this work, systematic investigations on the thermal conductivities of BiSbTe lump, microstructured pristine BiSbTe bulk and single wall carbon nanotubes (SWCNTs)/BiSbTe bulk nanocomposites were performed. BiSbTe lumps were crushed to form a coarse powder (200 µm) and effect of particle size reduction on the effective thermal conductivity of BiSbTe (200 µm) bulk were analyzed. For further reduction in the conductivity, a two pronged strategy has been employed. First, additional refinement of BiSbTe (200 µm) were performed through ball milling in an inert environment. Second, SWCNTs in 0.75, and 1.0 vol% were distributed uniformly in the fine BiSbTe ball milled powder. The results showed that the effective thermal conductivities decrease with the reduction in the particle size from lump to BiSbTe (200 µm) bulk as well as with the addition of SWCNTs accompanied by further refinement of BiSbTe particles. The significant reduction in thermal conductivities of the lump was achieved for pure BiSbTe (200 µm) bulk and 0.75 vol% of SWCNTs/BiSbTe composite. This can be ascribed to the enhanced phonon scattering by the grain boundaries between the nanostructured BiSbTe particles as well as the interfaces between BiSbTe and the low dimensional carbon nanotubes.

  18. Effect of cryogenic treatment on thermal conductivity properties of copper

    Science.gov (United States)

    Nadig, D. S.; Ramakrishnan, V.; Sampathkumaran, P.; Prashanth, C. S.

    2012-06-01

    Copper exhibits high thermal conductivity properties and hence it is extensively used in cryogenic applications like cold fingers, heat exchangers, etc. During the realization of such components, copper undergoes various machining operations from the raw material stage to the final component. During these machining processes, stresses are induced within the metal resulting in internal stresses, strains and dislocations. These effects build up resistance paths for the heat carriers which transfer heat from one location to the other. This in turn, results in reduction of thermal conductivity of the conducting metal and as a result the developed component will not perform as per expectations. In the process of cryogenic treatment, the metal samples are exposed to cryogenic temperature for extended duration of time for 24 hours and later tempered. During this process, the internal stresses and strains are reduced with refinement of the atomic structure. These effects are expected to favourably improve thermal conductivity properties of the metal. In this experimental work, OFHC copper samples were cryotreated for 24 hours at 98 K and part of them were tempered at 423K for one hour. Significant enhancement of thermal conductivity values were observed after cryotreating and tempering the copper samples.

  19. Reduction in thermal conductivity of BiSbTe lump

    Energy Technology Data Exchange (ETDEWEB)

    Ahmad, Kaleem [King Saud University, Sustainable Energy Technologies Center, College of Engineering, PO Box 800, Riyadh (Saudi Arabia); Wan, C. [Tsinghua University, State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineering, Beijing (China); Al-Eshaikh, M.A.; Kadachi, A.N. [King Saud University, Research Center, College of Engineering, PO Box 800, Riyadh (Saudi Arabia)

    2017-03-15

    In this work, systematic investigations on the thermal conductivities of BiSbTe lump, microstructured pristine BiSbTe bulk and single wall carbon nanotubes (SWCNTs)/BiSbTe bulk nanocomposites were performed. BiSbTe lumps were crushed to form a coarse powder (200 μm) and effect of particle size reduction on the effective thermal conductivity of BiSbTe (200 μm) bulk were analyzed. For further reduction in the conductivity, a two pronged strategy has been employed. First, additional refinement of BiSbTe (200 μm) were performed through ball milling in an inert environment. Second, SWCNTs in 0.75, and 1.0 vol% were distributed uniformly in the fine BiSbTe ball milled powder. The results showed that the effective thermal conductivities decrease with the reduction in the particle size from lump to BiSbTe (200 μm) bulk as well as with the addition of SWCNTs accompanied by further refinement of BiSbTe particles. The significant reduction in thermal conductivities of the lump was achieved for pure BiSbTe (200 μm) bulk and 0.75 vol% of SWCNTs/BiSbTe composite. This can be ascribed to the enhanced phonon scattering by the grain boundaries between the nanostructured BiSbTe particles as well as the interfaces between BiSbTe and the low dimensional carbon nanotubes. (orig.)

  20. Developing a High Thermal Conductivity Fuel with Silicon Carbide Additives

    Energy Technology Data Exchange (ETDEWEB)

    baney, Ronald; Tulenko, James

    2012-11-20

    The objective of this research is to increase the thermal conductivity of uranium oxide (UO{sub 2}) without significantly impacting its neutronic properties. The concept is to incorporate another high thermal conductivity material, silicon carbide (SiC), in the form of whiskers or from nanoparticles of SiC and a SiC polymeric precursor into UO{sub 2}. This is expected to form a percolation pathway lattice for conductive heat transfer out of the fuel pellet. The thermal conductivity of SiC would control the overall fuel pellet thermal conductivity. The challenge is to show the effectiveness of a low temperature sintering process, because of a UO{sub 2}-SiC reaction at 1,377°C, a temperature far below the normal sintering temperature. Researchers will study three strategies to overcome the processing difficulties associated with pore clogging and the chemical reaction of SiC and UO{sub 2} at temperatures above 1,300°C:

  1. Thermally Conductive-Silicone Composites with Thermally Reversible Cross-links.

    Science.gov (United States)

    Wertz, J T; Kuczynski, J P; Boday, D J

    2016-06-08

    Thermally conductive-silicone composites that contain thermally reversible cross-links were prepared by blending diene- and dienophile-functionalized polydimethylsiloxane (PDMS) with an aluminum oxide conductive filler. This class of thermally conductive-silicones are useful as thermal interface materials (TIMs) within Information Technology (IT) hardware applications to allow rework of valuable components. The composites were rendered reworkable via retro Diels-Alder cross-links when temperatures were elevated above 130 °C and required little mechanical force to remove, making them advantageous over other TIM materials. Results show high thermal conductivity (0.4 W/m·K) at low filler loadings (45 wt %) compared to other TIM solutions (>45 wt %). Additionally, the adhesion of the material was found to be ∼7 times greater at lower temperatures (25 °C) and ∼2 times greater at higher temperatures (120 °C) than commercially available TIMs.

  2. Thermal conductivity of nonlinear waves in disordered chains

    Indian Academy of Sciences (India)

    Sergej Flach; Mikhail Ivanchenko; Nianbei Li

    2011-11-01

    We present computational data on the thermal conductivity of nonlinear waves in disordered chains. Disorder induces Anderson localization for linear waves and results in a vanishing conductivity. Cubic nonlinearity restores normal conductivity, but with a strongly temperature-dependent conductivity (). We find indications for an asymptotic low-temperature ∼ 4 and intermediate temperature ∼ 2 laws. These findings are in accord with theoretical studies of wave packet spreading, where a regime of strong chaos is found to be intermediate, followed by an asymptotic regime of weak chaos (Laptyeva et al, Europhys. Lett. 91, 30001 (2010)).

  3. Simulations of thermal conductance across tilt grain boundaries in graphene

    Institute of Scientific and Technical Information of China (English)

    Peng Wang; Bo Gong; Qiong Feng; Hong-Tao Wang

    2012-01-01

    Non-equilibrium molecular dynamics (MD) method was performed to simulate the thermal transportation process in graphene nanoribbons (GNRs).A convenient way was conceived to introduce tilt grain boundaries (GBs) into the graphene lattice by repetitive removing C atom rows along certain directions.Comprehensive MD simulations reveal that larger-angle GBs are effective thermal barriers and substantially reduce the average thermal conductivity of GNRs.The GB thermal conductivity is ~ 10 W.m-1·K-1 for a bicrystal GNR with a misorientation of 21.8°,which is ~97% less than that of a prefect GNR with the same size.The total thermal resistance has a monotonic dependence on the density of the 5-7 defects along the GBs.A theoretical model is proposed to capture this relation and resolve the contributions by both the reduction in the phonon mean free path and the defect-induced thermal resistance.

  4. Thermal conductivity and rectification study of restructured Graphene

    Science.gov (United States)

    Arora, Anuj

    Electronics' miniaturization, has led to search for better thermal management techniques and discovery of important transport phenomenon. Thermal rectification, directionally preferential heat transport analogous to electrical diode, is one such technique, garnering tremendous interest. Its possibility has been explored through structural asymmetry, introducing a differential phonon density of states in hot and cold regions. As of now, mass and shape asymmetries have been studied, both experimentally and theoretically. However, strict requirements of material length being shorter than phonon mean free path and phonon coherence preservation at surface, makes connecting two materials with different temperature-dependent thermal conductivities, a more natural approach. To avoid resultant thermal boundary resistance and integration complexities, we achieve the affect in single material, by restructuring a region of Graphene by introducing defects. The asymmetry impedes ballistic phonon transport, modulating temperature dependence of thermal conductivity in the two regions. We perform deviational Monte Carlo simulations based on Energy-based formulation to microscopically investigate phonon transport, possibility and optimal conditions for thermal rectification. The proposed method uses phonon properties obtained from first principle, treat phonon-boundary scattering explicitly with properties drawn from Bose-Einstein Distribution.

  5. Strain- and defect-mediated thermal conductivity in silicon nanowires.

    Science.gov (United States)

    Murphy, Kathryn F; Piccione, Brian; Zanjani, Mehdi B; Lukes, Jennifer R; Gianola, Daniel S

    2014-07-09

    The unique thermal transport of insulating nanostructures is attributed to the convergence of material length scales with the mean free paths of quantized lattice vibrations known as phonons, enabling promising next-generation thermal transistors, thermal barriers, and thermoelectrics. Apart from size, strain and defects are also known to drastically affect heat transport when introduced in an otherwise undisturbed crystalline lattice. Here we report the first experimental measurements of the effect of both spatially uniform strain and point defects on thermal conductivity of an individual suspended nanowire using in situ Raman piezothermography. Our results show that whereas phononic transport in undoped Si nanowires with diameters in the range of 170-180 nm is largely unaffected by uniform elastic tensile strain, another means of disturbing a pristine lattice, namely, point defects introduced via ion bombardment, can reduce the thermal conductivity by over 70%. In addition to discerning surface- and core-governed pathways for controlling thermal transport in phonon-dominated insulators and semiconductors, we expect our novel approach to have broad applicability to a wide class of functional one- and two-dimensional nanomaterials.

  6. Fractional Heat Conduction Models and Thermal Diffusivity Determination

    Directory of Open Access Journals (Sweden)

    Monika Žecová

    2015-01-01

    Full Text Available The contribution deals with the fractional heat conduction models and their use for determining thermal diffusivity. A brief historical overview of the authors who have dealt with the heat conduction equation is described in the introduction of the paper. The one-dimensional heat conduction models with using integer- and fractional-order derivatives are listed. Analytical and numerical methods of solution of the heat conduction models with using integer- and fractional-order derivatives are described. Individual methods have been implemented in MATLAB and the examples of simulations are listed. The proposal and experimental verification of the methods for determining thermal diffusivity using half-order derivative of temperature by time are listed at the conclusion of the paper.

  7. Thermal conductivity and contact resistance of metal foams

    Science.gov (United States)

    Sadeghi, E.; Hsieh, S.; Bahrami, M.

    2011-03-01

    Accurate information on heat transfer and temperature distribution in metal foams is necessary for design and modelling of thermal-hydraulic systems incorporating metal foams. The analysis of heat transfer requires determination of the effective thermal conductivity as well as the thermal contact resistance (TCR) associated with the interface between the metal foam and the adjacent surfaces/layers. In this study, a test bed that allows the separation of effective thermal conductivity and TCR in metal foams is described. Measurements are performed in a vacuum under varying compressive loads using ERG Duocel aluminium foam samples with different porosities and pore densities. Also, a graphical method associated with a computer code is developed to demonstrate the distribution of contact spots and estimate the real contact area at the interface. Our results show that the porosity and the effective thermal conductivity remain unchanged with the variation of compression in the range 0-2 MPa; but TCR decreases significantly with pressure due to an increase in the real contact area at the interface. Moreover, the ratio of real to nominal contact area varies between 0 and 0.013, depending upon the compressive force, porosity, pore density and surface characteristics.

  8. Physical-Statistical Model of Thermal Conductivity of Nanofluids

    Directory of Open Access Journals (Sweden)

    B. Usowicz

    2014-01-01

    Full Text Available A physical-statistical model for predicting the effective thermal conductivity of nanofluids is proposed. The volumetric unit of nanofluids in the model consists of solid, liquid, and gas particles and is treated as a system made up of regular geometric figures, spheres, filling the volumetric unit by layers. The model assumes that connections between layers of the spheres and between neighbouring spheres in the layer are represented by serial and parallel connections of thermal resistors, respectively. This model is expressed in terms of thermal resistance of nanoparticles and fluids and the multinomial distribution of particles in the nanofluids. The results for predicted and measured effective thermal conductivity of several nanofluids (Al2O3/ethylene glycol-based and Al2O3/water-based; CuO/ethylene glycol-based and CuO/water-based; and TiO2/ethylene glycol-based are presented. The physical-statistical model shows a reasonably good agreement with the experimental results and gives more accurate predictions for the effective thermal conductivity of nanofluids compared to existing classical models.

  9. Sub-amorphous thermal conductivity in ultrathin crystalline silicon nanotubes.

    Science.gov (United States)

    Wingert, Matthew C; Kwon, Soonshin; Hu, Ming; Poulikakos, Dimos; Xiang, Jie; Chen, Renkun

    2015-04-08

    Thermal transport behavior in nanostructures has become increasingly important for understanding and designing next generation electronic and energy devices. This has fueled vibrant research targeting both the causes and ability to induce extraordinary reductions of thermal conductivity in crystalline materials, which has predominantly been achieved by understanding that the phonon mean free path (MFP) is limited by the characteristic size of crystalline nanostructures, known as the boundary scattering or Casimir limit. Herein, by using a highly sensitive measurement system, we show that crystalline Si (c-Si) nanotubes (NTs) with shell thickness as thin as ∼5 nm exhibit a low thermal conductivity of ∼1.1 W m(-1) K(-1). Importantly, this value is lower than the apparent boundary scattering limit and is even about 30% lower than the measured value for amorphous Si (a-Si) NTs with similar geometries. This finding diverges from the prevailing general notion that amorphous materials represent the lower limit of thermal transport but can be explained by the strong elastic softening effect observed in the c-Si NTs, measured as a 6-fold reduction in Young's modulus compared to bulk Si and nearly half that of the a-Si NTs. These results illustrate the potent prospect of employing the elastic softening effect to engineer lower than amorphous, or subamorphous, thermal conductivity in ultrathin crystalline nanostructures.

  10. Modeling Interfacial Thermal Boundary Conductance of Engineered Interfaces

    Science.gov (United States)

    2014-08-31

    involving carbon materials. Determined scaling laws for conductivity of carbon nanotube networks [11]. Modified the DMM to predict hBD at metal–graphite...111, 084310 (2012). 11A. N. Volkov and L. V. Zhigilei, “Scaling laws and mesoscopic modeling of thermal conductivity in carbon nanotube materials...instead from an algebraic expression that accurately reproduces the MD results but with negligible computational expense. This permitted a large

  11. Liquid-like thermal conduction in a crystalline solid

    OpenAIRE

    B. Li; Kawakita, Y.; Zhang, Q.; Wang, H.; Feygenson, M.; Yu, H. L.; Wu, D; Ohara, K.; Kikuchi, T.; Shibata, K; Yamada, T; Chen, Y.(California Institute of Technology, Pasadena, USA); J. Q. He; Vaknin, D.; Wu, R. Q.

    2017-01-01

    A solid conducts heat through both transverse and longitudinal acoustic phonons, but a liquid employs only longitudinal vibrations. Here, we report that the crystalline solid AgCrSe2 has liquid-like thermal conduction. In this compound, Ag atoms exhibit a dynamic duality that they are exclusively involved in intense low-lying transverse acoustic phonons while they also undergo local fluctuations inherent in an order-to-disorder transition occurring at 450 K. As a consequence of this extreme d...

  12. System to Measure Thermal Conductivity and Seebeck Coefficient for Thermoelectrics

    Science.gov (United States)

    Kim, Hyun-Jung; Skuza, Jonathan R.; Park, Yeonjoon; King, Glen C.; Choi, Sang H.; Nagavalli, Anita

    2012-01-01

    The Seebeck coefficient, when combined with thermal and electrical conductivity, is an essential property measurement for evaluating the potential performance of novel thermoelectric materials. However, there is some question as to which measurement technique(s) provides the most accurate determination of the Seebeck coefficient at elevated temperatures. This has led to the implementation of nonstandardized practices that have further complicated the confirmation of reported high ZT materials. The major objective of the procedure described is for the simultaneous measurement of the Seebeck coefficient and thermal diffusivity within a given temperature range. These thermoelectric measurements must be precise, accurate, and reproducible to ensure meaningful interlaboratory comparison of data. The custom-built thermal characterization system described in this NASA-TM is specifically designed to measure the inplane thermal diffusivity, and the Seebeck coefficient for materials in the ranging from 73 K through 373 K.

  13. Interlayer thermal conductance within a phosphorene and graphene bilayer.

    Science.gov (United States)

    Hong, Yang; Zhang, Jingchao; Zeng, Xiao Cheng

    2016-11-24

    Monolayer graphene possesses unusual thermal properties, and is often considered as a prototype system for the study of thermal physics of low-dimensional electronic/thermal materials, despite the absence of a direct bandgap. Another two-dimensional (2D) atomic layered material, phosphorene, is a natural p-type semiconductor and it has attracted growing interest in recent years. When a graphene monolayer is overlaid on phosphorene, the hybrid van der Waals (vdW) bilayer becomes a potential candidate for high-performance thermal/electronic applications, owing to the combination of the direct-bandgap properties of phosphorene with the exceptional thermal properties of graphene. In this work, the interlayer thermal conductance at the phosphorene/graphene interface is systematically investigated using classical molecular dynamics (MD) simulation. The transient pump-probe heating method is employed to compute the interfacial thermal resistance (R) of the bilayer. The predicted R value at the phosphorene/graphene interface is 8.41 × 10(-8) K m(2) W(-1) at room temperature. Different external and internal conditions, i.e., temperature, contact pressure, vacancy defect, and chemical functionalization, can all effectively reduce R at the interface. Numerical results of R reduction as a function of temperature, interfacial coupling strength, defect ratio, or hydrogen coverage are reported with the most R reduction amounting to 56.5%, 70.4%, 34.8% and 84.5%, respectively.

  14. Thermal Conductivity of Polyimide/Carbon Nanofiller Blends

    Science.gov (United States)

    Ghose, S.; Watson, K. A.; Delozier, D. M.; Working, D. C.; Connell, J. W.; Smith, J. G.; Sun, Y. P.; Lin, Y.

    2007-01-01

    In efforts to improve the thermal conductivity (TC) of Ultem(TM) 1000, it was compounded with three carbon based nano-fillers. Multiwalled carbon nanotubes (MWCNT), vapor grown carbon nanofibers (CNF) and expanded graphite (EG) were investigated. Ribbons were extruded to form samples in which the nano-fillers were aligned. Samples were also fabricated by compression molding in which the nano-fillers were randomly oriented. The thermal properties were evaluated by DSC and TGA, and the mechanical properties of the aligned samples were determined by tensile testing. The degree of dispersion and alignment of the nanoparticles were investigated with high-resolution scanning electron microscopy. The thermal conductivity of the samples was measured in both the direction of alignment as well as perpendicular to that direction using the Nanoflash technique. The results of this study will be presented.

  15. Boosting Magnetic Reconnection by Viscosity and Thermal Conduction

    CERN Document Server

    Minoshima, Takashi; Imada, Shinsuke

    2016-01-01

    Nonlinear evolution of magnetic reconnection is investigated by means of magnetohydrodynamic simulations including uniform resistivity, uniform viscosity, and anisotropic thermal conduction. When viscosity exceeds resistivity (the magnetic Prandtl number Prm > 1), the viscous dissipation dominates outflow dynamics and leads to the decrease in the plasma density inside a current sheet. The low-density current sheet supports the excitation of the vortex. The thickness of the vortex is broader than that of the current for Prm > 1. The broader vortex flow more efficiently carries the upstream magnetic flux toward the reconnection region, and consequently boosts the reconnection. The reconnection rate increases with viscosity provided that thermal conduction is fast enough to take away the thermal energy increased by the viscous dissipation (the fluid Prandtl number Pr < 1). The result suggests the need to control the Prandtl numbers for the reconnection against the conventional resistive model.

  16. Single nanowire thermal conductivity measurements by Raman thermography.

    Science.gov (United States)

    Doerk, Gregory S; Carraro, Carlo; Maboudian, Roya

    2010-08-24

    A facile, rapid, and nondestructive technique for determining the thermal conductivity of individual nanowires based on Raman temperature mapping has been demonstrated. Using calculated absorption efficiencies, the thermal conductivities of single cantilevered Si nanowires grown by the vapor-liquid-solid method are measured and the results agree well with values predicted by diffuse phonon boundary scattering. As a measurement performed on the wire, thermal contact effects are avoided and ambient air convection is found to be negligible for the range of diameters measured. The method's versatility is further exemplified in the reverse measurement of a single nanowire absorption efficiency assuming diffuse phonon boundary scattering. The results presented here outline the broad utility that Raman thermography may have for future thermoelectric and photovoltaic characterization of nanostructures.

  17. Thermal Conductivity of Pyroclastic Soil ( Pozzolana) from the Environs of Rome

    Science.gov (United States)

    McCombie, M. L.; Tarnawski, V. R.; Bovesecchi, G.; Coppa, P.; Leong, W. H.

    2017-02-01

    The paper reveals the experimental procedure and thermo-physical characteristics of a coarse pyroclastic soil ( Pozzolana), from the neighborhoods of Rome, Italy. The tested samples are comprised of 70.7 % sand, 25.9 % silt, and 3.4 % clay. Their mineral composition contained 38 % pyroxene, 33 % analcime, 20 % leucite, 6 % illite/muscovite, 3 % magnetite, and no quartz content was noted. The effective thermal conductivity of minerals was assessed to be about 2.14 W{\\cdot } m^{-1}{\\cdot } K^{-1}. A transient thermal probe method was applied to measure the thermal conductivity (λ ) over a full range of the degree of saturation (Sr), at two porosities ( n) of 0.44 and 0.50, and at room temperature of about 25°C. The λ data obtained were consistent between tests and showed an increasing trend with increasing Sr and decreasing n. At full saturation (Sr=1), a nearly quintuple λ increase was observed with respect to full dryness (Sr=0). In general, the measured data closely followed the natural trend of λ versus Sr exhibited by published data at room temperature for other unsaturated soils and sands. The measured λ data had an average root-mean-squared error (RMSE) of 0.007 W{\\cdot } m^{-1}{\\cdot } K^{-1} and 0.008 W{\\cdot } m^{-1}{\\cdot } K^{-1} for n of 0.50 and 0.44, respectively, as well as an average relative standard deviation of the mean at the 95 % confidence level (RSDM_{0.95}) of 2.21 % and 2.72 % for n of 0.50 and 0.44, respectively.

  18. Pressure effects on thermal conductivity and expansion of geologic materials

    Energy Technology Data Exchange (ETDEWEB)

    Sweet, J.N.

    1979-02-01

    Through analysis of existing data, an estimate is made of the effect of pressure or depth on the thermal conductivity and expansion of geologic materials which could be present in radioactive waste repositories. In the case of homogeneous dense materials, only small shifts are predicted to occur at depths less than or equal to 3 km, and these shifts will be insignificant as compared with those caused by temperature variations. As the porosity of the medium increases, the variation of conductivity and expansion with pressure becomes greater, with conductivity increasing and expansion decreasing as pressure increases. The pressure dependence of expansion can be found from data on the temperature variation of the isobaric compressibility. In a worst case estimate, a decrease in expansion of approx. 25% is predicted for 5% porous sandstone at a depth of 3 km. The thermal conductivity of a medium with gaseous inclusions increases as the porosity decreases, with the magnitude of the increase being dependent on the details of the porosity collapse. Based on analysis of existing data on tuff and sandstone, a weighted geometric mean formula is recommended for use in calculating the conductivity of porous rock. As a result of this study, it is recommended that measurement of rock porosity versus depth receive increased attention in exploration studies and that the effect of porosity on thermal conductivity and expansion should be examined in more detail.

  19. Interplay of variable thermal conductivity and expansivity on the thermal structure of oceanic lithosphere

    Science.gov (United States)

    Honda, S.; Yuen, D. A.

    The sensitivity of pressure- and temperature-dependent thermal conductivity (k: W/m/K) and the thermal expansivity (α:1/K) on the thermal structure of the oceanic plate is investigated parametrically by comparing the ocean floor depth and heat flux calculated by one-dimensional conduction model with those of GDH1, a theoretical thermal model of the oceanic lithosphere. We find that an optimum fit is obtained, when the value of thermal expansivity is ˜ 3 × 10-5, while those associated with the thermal conductivity have many possibilities. The estimates, which give an equally good fit to the GDH1 model, of the plate thickness D (km) and the temperature at the base of the plate Tm (°C) may be given by Tm ˜ 1450-(k0-4.5) × 100-(α-3.0 × 10-5) × 105×100, D ˜ 90 + (k0-4.5) × 20 - (α-3.0 × 10-5) × 105 × 20 where k0 (W/m/K) is the lattice thermal conductivity at the ocean floor. A similar relation is obtained for constant thermal conductivity.

  20. Short hot wire technique for measuring thermal conductivity and thermal diffusivity of various materials

    Science.gov (United States)

    Xie, Huaqing; Gu, Hua; Fujii, Motoo; Zhang, Xing

    2006-01-01

    A transient short hot wire technique (SHWT) is developed for simultaneous determination of the thermal conductivity and thermal diffusivity of various materials such as liquids, gases or powders. A metal wire with (or without) insulation coating serves both as a heating unit and as an electrical resistance thermometer and the wire is calibrated using water and toluene with known thermophysical properties. This SHWT includes correlation of the experimental data with numerically simulated values based on a two-dimensional heat-conduction model. For the measurements with proportional relation between temperature rise and logarithmic heating time interval, the thermal conductivity and thermal diffusivity are obtained from the slope and the intercept of the measured temperature rise and those of calculated non-dimensional temperature rise by including the heat flux and the properties of the wire. For the measurements with nonlinear relation between temperature rise and logarithmic heating time interval, the thermal conductivity and thermal diffusivity are extracted from a curve fitting method by using the downhill simplex method to match the experimental data and the numerical values. This technique is applied here using air as a testing sample. The effect of natural convection is investigated and the accuracy of this measurement is estimated to be 2% for thermal conductivity and 7% for thermal diffusivity.

  1. Minimized thermal conductivity in highly stable thermal barrier W/ZrO2 multilayers

    Science.gov (United States)

    Döring, Florian; Major, Anna; Eberl, Christian; Krebs, Hans-Ulrich

    2016-10-01

    Nanoscale thin-film multilayer materials are of great research interest since their large number of interfaces can strongly hinder phonon propagation and lead to a minimized thermal conductivity. When such materials provide a sufficiently small thermal conductivity and feature in addition also a high thermal stability, they would be possible candidates for high-temperature applications such as thermal barrier coatings. For this article, we have used pulsed laser deposition in order to fabricate thin multilayers out of the thermal barrier material ZrO2 in combination with W, which has both a high melting point and high density. Layer thicknesses were designed such that bulk thermal conductivity is governed by the low value of ZrO2, while ultrathin W blocking layers provide a high number of interfaces. By this phonon scattering, reflection and shortening of mean free path lead to a significant reduction in overall thermal conductivity even below the already low value of ZrO2. In addition to this, X-ray reflectivity measurements were taken showing strong Bragg peaks even after annealing such multilayers at 1300 K. Those results identify W/ZrO2 multilayers as desired thermally stable, low-conductivity materials.

  2. Minimized thermal conductivity in highly stable thermal barrier W/ZrO{sub 2} multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Doering, Florian; Major, Anna; Eberl, Christian; Krebs, Hans-Ulrich [University of Goettingen, Institut fuer Materialphysik, Goettingen (Germany)

    2016-10-15

    Nanoscale thin-film multilayer materials are of great research interest since their large number of interfaces can strongly hinder phonon propagation and lead to a minimized thermal conductivity. When such materials provide a sufficiently small thermal conductivity and feature in addition also a high thermal stability, they would be possible candidates for high-temperature applications such as thermal barrier coatings. For this article, we have used pulsed laser deposition in order to fabricate thin multilayers out of the thermal barrier material ZrO{sub 2} in combination with W, which has both a high melting point and high density. Layer thicknesses were designed such that bulk thermal conductivity is governed by the low value of ZrO{sub 2}, while ultrathin W blocking layers provide a high number of interfaces. By this phonon scattering, reflection and shortening of mean free path lead to a significant reduction in overall thermal conductivity even below the already low value of ZrO{sub 2}. In addition to this, X-ray reflectivity measurements were taken showing strong Bragg peaks even after annealing such multilayers at 1300 K. Those results identify W/ZrO{sub 2} multilayers as desired thermally stable, low-conductivity materials. (orig.)

  3. Thermally stimulated discharge conductivity in polymer composite thin films

    Indian Academy of Sciences (India)

    V S Sangawar; P S Chikhalikar; R J Dhokne; A U Ubale; S D Meshram

    2006-08-01

    This paper describes the results of thermally stimulated discharge conductivity study of activated charcoal–polyvinyl chloride (PVC) thin film thermoelectrets. TSDC has been carried out in the temperature range 308–400°K and at four different polarizing fields. Results are discussed on the basis of mobility of activated charcoal and polyvinyl chloride chains.

  4. Thermal conductivity of MoS2 polycrystalline nanomembranes

    Science.gov (United States)

    Sledzinska, M.; Graczykowski, B.; Placidi, M.; Saleta Reig, D.; El Sachat, A.; Reparaz, J. S.; Alzina, F.; Mortazavi, B.; Quey, R.; Colombo, L.; Roche, S.; Sotomayor Torres, C. M.

    2016-09-01

    Heat conduction in 2D materials can be effectively engineered by means of controlling nanoscale grain structure. A favorable thermal performance makes these structures excellent candidates for integrated heat management units. Here we show combined experimental and theoretical studies for MoS2 nanosheets in a nanoscale grain-size limit. We report thermal conductivity measurements on 5 nm thick polycrystalline MoS2 by means of 2-laser Raman thermometry. The free-standing, drum-like MoS2 nanomembranes were fabricated using a novel polymer- and residue-free, wet transfer, in which we took advantage of the difference in the surface energies between MoS2 and the growth substrate to transfer the CVD-grown nanosheets. The measurements revealed a strong reduction in the in-plane thermal conductivity down to about 0.73 ± 0.25 {{{W}}{{m}}}-1 {{{K}}}-1. The results are discussed theoretically using finite elements method simulations for a polycrystalline film, and a scaling trend of the thermally conductivity with grain size is proposed.

  5. Thermal Conductivity of Tetryl by Modulated Differential Scanning Calorimetry

    Energy Technology Data Exchange (ETDEWEB)

    Weese, R K

    2003-07-28

    We investigated the use of the Modulated Differential Scanning Calorimeter to measure thermal conductivity (K) of the explosive, Tetryl, using two different methods, isothermal and nonthermal. A discussion of our methods and a comparison of our measured values to literature values of K for Tetryl, which deviated by as much as 50%, will be presented.

  6. Decreasing the Effective Thermal Conductivity in Glass Supported Thermoelectric Layers.

    Science.gov (United States)

    Bethke, Kevin; Andrei, Virgil; Rademann, Klaus

    2016-01-01

    As thermoelectric devices begin to make their way into commercial applications, the emphasis is put on decreasing the thermal conductivity. In this purely theoretical study, finite element analysis is used to determine the effect of a supporting material on the thermal conductivity of a thermoelectric module. The simulations illustrate the heat transfer along a sample, consisting from Cu, Cu2O and PbTe thermoelectric layers on a 1 mm thick Pyrex glass substrate. The influence of two different types of heating, at a constant temperature and at a constant heat flux, is also investigated. It is revealed that the presence of a supporting material plays an important role on lowering the effective thermal conductivity of the layer-substrate ensemble. By using thinner thermoelectric layers the effective thermal conductivity is further reduced, almost down to the value of the glass substrate. As a result, the temperature gradient becomes steeper for a fixed heating temperature, which allows the production of devices with improved performance under certain conditions. Based on the simulation results, we also propose a model for a robust thin film thermoelectric device. With this suggestion, we invite the thermoelectric community to prove the applicability of the presented concept for practical purposes.

  7. Well-log based prediction of thermal conductivity

    DEFF Research Database (Denmark)

    Fuchs, Sven; Förster, Andrea

    Rock thermal conductivity (TC) is paramount for the determination of heat flow and the calculation of temperature profiles. Due to the scarcity of drill cores compared to the availability of petrophysical well logs, methods are desired to indirectly predict TC in sedimentary basins. Most...

  8. Thermal conductivity measurement by the 3omega method

    NARCIS (Netherlands)

    Bourlon, A.B.; Van der Tempel, L.

    2006-01-01

    ABSTRACT: The power of LEDs increases exponentially over the years,while the mean time to failure (MTTF) should remain >100000 hours. The reliability requirement limits the junction temperature and the thermo elastic stresses, which are roughly inversely proportional tothe thermal conductivity of th

  9. Fabrication of setup for high temperature thermal conductivity measurement

    Science.gov (United States)

    Patel, Ashutosh; Pandey, Sudhir K.

    2017-01-01

    In this work, we report the fabrication of an experimental setup for high temperature thermal conductivity (κ) measurement. It can characterize samples with various dimensions and shapes. Steady state based axial heat flow technique is used for κ measurement. Heat loss is measured using parallel thermal conductance technique. Simple design, lightweight, and small size sample holder is developed by using a thin heater and limited components. Low heat loss value is achieved by using very low thermal conductive insulator block with small cross-sectional area. Power delivered to the heater is measured accurately by using 4-wire technique and for this, the heater is developed with 4 wires. This setup is validated by using Bi0.36Sb1.45Te3, polycrystalline bismuth, gadolinium, and alumina samples. The data obtained for these samples are found to be in good agreement with the reported data. The maximum deviation of 6% in the value κ is observed. This maximum deviation is observed with the gadolinium sample. We also report the thermal conductivity of polycrystalline tellurium from 320 K to 550 K and the nonmonotonous behavior of κ with temperature is observed.

  10. Prediction of the effective thermal conductivity of microsphere insulation

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Ling Xue; Park, Ji Ho; Lee, Cheon Kyu; Seo, Man Su; Jeong, Sang Kwon [Cryogenic Engineering Laboratory, Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

    2014-03-15

    Since glass microsphere has high crush strength, low density and small particle size, it becomes alternative thermal insulation material for cryogenic systems, such as storage and transportation tank for cryogenic fluids. Although many experiments have been performed to verify the effective thermal conductivity of microsphere, prediction by calculation is still inaccurate due to the complicated geometries, including wide range of powder diameter distribution and different pore sizes. The accurate effective thermal conductivity model for microsphere is discussed in this paper. There are four mechanisms which contribute to the heat transfer of the evacuated powder: gaseous conduction (k{sub g}), solid conduction (k{sub s}), radiation (k{sub r}) and thermal contact (k{sub c}). Among these components, k{sub g} and k{sub s} were calculated by Zehner and Schlunder model (1970). Other component values for k{sub c} and k{sub r}, which were obtained from experimental data under high vacuum conditions were added. In this research paper, the geometry of microsphere was simplified as a homogeneous solid sphere. The calculation results were compared with previous experimental data by R. Wawryk (1988), H. S. Kim (2010) and the experiment of this paper to show good agreement within error of 46%, 4.6% and 17 % for each result.

  11. Porous alumina and zirconia ceramics with tailored thermal conductivity

    Science.gov (United States)

    Gregorová, E.; Pabst, W.; Sofer, Z.; Jankovský, O.; Matějíček, J.

    2012-11-01

    The thermal conductivity of porous ceramics can be tailored by slip casting and uniaxial dry pressing, using either fugitive pore formers (saccharides) or partial sintering. Porous alumina and zirconia ceramics have been prepared using appropriate powder types (ungranulated for casting, granulated for pressing) and identical firing regimes (but different maximum temperatures in the case of partial sintering). Thermal diffusivities have been measured by the laser- and xenon-flash method and transformed into relative thermal conductivities, which enable a temperature-independent comparison between different materials. While the porosity can be controlled in a similar way for both materials when using pore formers, partial sintering exhibits characteristic differences between alumina and zirconia (for alumina porosities below 45 %, full density above 1600 °C, for zirconia porosities below 60 %, full density above 1300 °C). The different compaction behavior of alumina and zirconia (porosity after pressing 0.465 and 0.597, respectively) is reflected in the fact that for alumina the relative conductivity data of partially sintered materials are below the exponential prediction, while for zirconia they coincide with the latter. Notwithstanding these characteristic differences, for both alumina and zirconia it is possible to tailor the thermal conductivity from 100 % down to approx. 15 % of the solid phase value.

  12. A method of measuring the thermal conductivity of liquids

    NARCIS (Netherlands)

    Held, E.F.M. van der; Drunen, F.G. van

    1949-01-01

    We described the development of an apparatus for the determination of the thermal conductivity of liquids. The apparatus is suitable for all kinds of liquids, including the strongest acids. From a given time we pass an electric current through a thin straight wire, placed in a homogeneous material o

  13. Dependence of thermal conductivity on structural parameters in porous samples

    Science.gov (United States)

    Miettinen, L.; Kekäläinen, P.; Turpeinen, T.; Hyväluoma, J.; Merikoski, J.; Timonen, J.

    2012-03-01

    The in-plane thermal conductivity of porous sintered bronze plates was studied both experimentally and numerically. We developed and validated an experimental setup, where the sample was placed in vacuum and heated while its time-dependent temperature field was measured with an infrared camera. The porosity and detailed three-dimensional structure of the samples were determined by X-ray microtomography. Lattice-Boltzmann simulations of thermal conductivity in the tomographic reconstructions of the samples were used to correct the contact area between bronze particles as determined by image analysis from the tomographic reconstructions. Small openings in the apparent contacts could not be detected with the imaging resolution used, and they caused an apparent thermal contact resistance between particles. With this correction included, the behavior of the measured thermal conductivity was successfully explained by an analytical expression, originally derived for regular structures, which involves three structural parameters of the porous structures. There was no simple relationship between heat conductivity and porosity.

  14. Dependence of thermal conductivity on structural parameters in porous samples

    Directory of Open Access Journals (Sweden)

    L. Miettinen

    2012-03-01

    Full Text Available The in-plane thermal conductivity of porous sintered bronze plates was studied both experimentally and numerically. We developed and validated an experimental setup, where the sample was placed in vacuum and heated while its time-dependent temperature field was measured with an infrared camera. The porosity and detailed three-dimensional structure of the samples were determined by X-ray microtomography. Lattice-Boltzmann simulations of thermal conductivity in the tomographic reconstructions of the samples were used to correct the contact area between bronze particles as determined by image analysis from the tomographic reconstructions. Small openings in the apparent contacts could not be detected with the imaging resolution used, and they caused an apparent thermal contact resistance between particles. With this correction included, the behavior of the measured thermal conductivity was successfully explained by an analytical expression, originally derived for regular structures, which involves three structural parameters of the porous structures. There was no simple relationship between heat conductivity and porosity.

  15. Thermal conductivity measurement by the 3omega method

    NARCIS (Netherlands)

    Bourlon, A.B.; Van der Tempel, L.

    2006-01-01

    ABSTRACT: The power of LEDs increases exponentially over the years,while the mean time to failure (MTTF) should remain >100000 hours. The reliability requirement limits the junction temperature and the thermo elastic stresses, which are roughly inversely proportional tothe thermal conductivity of

  16. Spectroscopic investigation of thermal conductivity in few-layer graphene

    Science.gov (United States)

    Denison, Joseph C., Jr.

    Carbon is an extremely versatile element due to the ability of its electronic structure to allow strong bonds with many elements including other carbon atoms. This allows for the formation of many types of large and complex architectures, such as fullerenes and carbon nanotubes, at the nanoscale. One of the most fascinating allotropes of carbon is graphene, a two-dimensional honeycomb lattice with carbon in sp2 hybridization, which building block for layered graphite and other nanocarbons.[1] Because of its unique structure, graphene displays several interesting properties including high thermal[2-4] and electrical mobility and conductivity[1,5]. The initial studies on graphene were performed on mechanically exfoliated samples, which were limited to few microns in size. In the recent years, large areas of single- and few-layer graphene (˜few cm x cm) are being produced by chemical vapor deposition technique for practical applications. However, chemical vapor deposition grown graphene is highly polycrystalline with interfaces such as edges, grain boundaries, dislocations, and point defects. This inevitable presence of defects in graphene influences its electrical and thermal transport. While many studies have previously focused on the influence of defects on electrical mobility and conductivity, there is little information on the influence of defects on the thermal properties of graphene. This study specifically investigates the effect of both intrinsic and extrinsic defects on the in-plane thermal properties of graphene using micro-Raman spectroscopy. The in-plane thermal conductivity of few-layered graphene (FLG) was measured using Raman spectroscopy, following the work of Balandin et al. [4]The thermal conductivity was estimated from a shift of the characteristic G-band of graphene as a function of the excitation laser power. The graphene samples were synthesized on nickel substrates using chemical vapor deposition, and transferred to copper TEM grids and

  17. Natural radioactivity in sand used in thermal therapy at the Red Sea Coast.

    Science.gov (United States)

    El-Arabi, A M

    2005-01-01

    The development of climatotherapy in Safaga opens the field of medical tourism in Egypt, in order to detect any harmful radiation that would affect the patients during treatment and is becoming important economic resource. Studies and survey of natural radiation and radioactivity in upper Egypt conducted since 1990, included monitoring of the concentration of natural radionuclides in environmental samples. The results of the study reveals that, for all sand samples, the mean activity concentration of 40K (618+/-122-548+/-82 Bq kg(-1)) are much higher than that of both 226Ra (25.3+/-14-20.6+/-10 Bq kg(-1)) and 232Th (21.4+/-10-22.4+/-10 Bq kg(-1)). Different radiation hazard indices were calculated, the radiation dose to which workers are subjected is not negligible (26.5-50.9 nGy h(-1)), although depending on the inhalation of dust.

  18. Enhancing Thermal Conductivity of Hexagonal Boron Nitride Filled Thermoplastics for Thermal Interface Management

    Science.gov (United States)

    Prindl, John

    Hexagonal Boron Nitride has been shown to enhance thermal conductivity in polymer composites more so than conventional ceramic fillers. However, to see a significant increase in thermal conductivity a high loading level of the advanced ceramic is often needed which can have an adverse effect on the mechanical behavior of the composite part. Applications for thermal management using thermal interface materials (TIM) continue to grow with thermoplastic injection molded parts emerging as an area for market growth. There is a growing need for published technical data in this particular area of application. In the current study, the thermal conductivity and mechanical behavior of hexagonal Boron Nitride (hBN) loaded thermoplastic composites is investigated. The main objectives of this work is produce a novel data package which illustrates the effects of hBN, loaded at high concentrations, across several different thermoplastic resins with the ultimate goal being to find a desirable formulation for specific thermal management applications. The desired properties for such applications being high thermal conductivity and high electrical resistivity with a minimal decrease in mechanical properties. Hexagonal BN cooling filler agglomerates were compounded into polypropylene (PP), nylon-6 (PA-6), and thermoplastic elastomer (TPE) via twin-screw extruder at 3 different loading levels. Injection molded samples were produced and characterized to show varying degrees of thermal conductivity and mechanical strength. Results from this research showed that in all cases, the thermal conductivity increased with increasing levels of hBN addition. The largest increases in thermal conductivity were seen in the PA-6 and TPE systems with the possible indication of exceeding the percolation threshold in the TPE system. This is hypothesized to occur due to the preferential migration of hBN to form conduction pathways around the elastomeric domains in the TPE matrix. Though TPE produced

  19. The Origin of High Thermal Conductivity and Ultralow Thermal Expansion in Copper-Graphite Composites.

    Science.gov (United States)

    Firkowska, Izabela; Boden, André; Boerner, Benji; Reich, Stephanie

    2015-07-08

    We developed a nanocomposite with highly aligned graphite platelets in a copper matrix. Spark plasma sintering ensured an excellent copper-graphite interface for transmitting heat and stress. The resulting composite has superior thermal conductivity (500 W m(-1) K(-1), 140% of copper), which is in excellent agreement with modeling based on the effective medium approximation. The thermal expansion perpendicular to the graphite platelets drops dramatically from ∼20 ppm K(-1) for graphite and copper separately to 2 ppm K(-1) for the combined structure. We show that this originates from the layered, highly anisotropic structure of graphite combined with residual stress under ambient conditions, that is, strain-engineering of the thermal expansion. Combining excellent thermal conductivity with ultralow thermal expansion results in ideal materials for heat sinks and other devices for thermal management.

  20. Illusion thermal device based on material with constant anisotropic thermal conductivity for location camouflage

    Science.gov (United States)

    Hou, Quanwen; Zhao, Xiaopeng; Meng, Tong; Liu, Cunliang

    2016-09-01

    Thermal metamaterials and devices based on transformation thermodynamics often require materials with anisotropic and inhomogeneous thermal conductivities. In this study, still based on the concept of transformation thermodynamics, we designed a planar illusion thermal device, which can delocalize a heat source in the device such that the temperature profile outside the device appears to be produced by a virtual source at another position. This device can be constructed by only one kind of material with constant anisotropic thermal conductivity. The condition which should be satisfied by the device is provided, and the required anisotropic thermal conductivity is then deduced theoretically. This study may be useful for the designs of metamaterials or devices since materials with constant anisotropic parameters have great facility in fabrication. A prototype device has been fabricated based on a composite composed by two naturally occurring materials. The experimental results validate the effectiveness of the device.

  1. Thermal conductivity and multiferroics of electroactive polymers and polymer composites

    Science.gov (United States)

    Jin, Jiezhu

    Electronically conducting polymers and electromechanical polymers are the two important branches of the cutting-edge electroactive polymers. They have shown significant impact on many modern technologies such as flat panel display, energy transport, energy conversion, sensors and actuators. To utilize conducting polymers in microelectronics, optoelectronics and thermoelectrics, it is necessary to have a comprehensive study of their thermal conductivity since thermal conductivity is a fundamental materials property that is particularly important and sometimes a determining factor of the device performance. For electromechanical polymers, larger piezoelectric effect will contribute to the improvement of magnetoelectric (ME) coupling efficiency in their multiferroic composites. This dissertation is devoted to characterizing electronically conducting polymers for their electrical and thermal conductivity, and developing new classes of electromechanical polymers and strain-mediated electromechanical polymer-based multiferroic ME composites. Conducting polymers opened up new possibilities for devices combining novel electrical and thermal properties, but there has been limited understanding of the length-scale effect of the electrical and thermal conductivity, and the mechanism underlying the electricity and heat transport behavior. In this dissertation, the analytical model and experimental technique are presented to measure the in-plane thermal conductivity of polyaniline thin films. For camphorsulfonic acid doped polyaniline patterned on silicon oxide/silicon substrate using photolithography and reactive ion etching, the thermal conductivity of the film with thickness of 20 nm is measured to be 0.0406 W/m˙K, which significantly deviates from their bulk (> 0.26 W/m˙K). The size effect on thermal conductivity at this scale is attributed to the significant phonon boundary scattering. When the film goes up to 130 nm thick, the thermal conductivity increases to 0.166 W

  2. Influence of moisture content and temperature on thermal conductivity and thermal diffusivity of rice flours

    Science.gov (United States)

    The thermal conductivity and thermal diffusivity of four types of rice flours and one type of rice protein were determine at temperatures ranging from 4.8 to 36.8 C, bulk densities 535 to 875.8 kg/m3, and moisture contents 2.6 to 16.7 percent (w.b.), using a KD2 Thermal Properties Analyzer. It was ...

  3. Determining the unsaturated hydraulic conductivity of a compacted sand-bentonite mixture under constant volume and free-swell conditions

    CERN Document Server

    Cui, Yu-Jun; Loiseau, Cyril; Delage, Pierre; 10.1016/j.pce.2008.10.017

    2008-01-01

    Highly compacted sand-bentonite mixtures are often considered as possible engineered barriers in deep high-level radioactive waste disposals. In-situ, the saturation of these barriers from their initially unsaturated state is a complex hydro-mechanical coupled process in which temperature effects also play a role. The key parameter of this process is the unsaturated hydraulic conductivity of the barrier. In this paper, isothermal infiltration experiments were conducted to determine the unsaturated hydraulic conductivity according to the instantaneous profile method. To do so, total suction changes were monitored at different locations along the soil specimen by using resistivity relative humidity probes. Three constant volume infiltration tests were conducted showing, unexpectedly, a decrease of the hydraulic conductivity during infiltration. One test performed under free-swell conditions showed the opposite and standard trend. These observations were interpreted in terms of microstructure changes during wett...

  4. Logarithmic divergent thermal conductivity in two-dimensional nonlinear lattices.

    Science.gov (United States)

    Wang, Lei; Hu, Bambi; Li, Baowen

    2012-10-01

    Heat conduction in three two-dimensional (2D) momentum-conserving nonlinear lattices are numerically calculated via both nonequilibrium heat-bath and equilibrium Green-Kubo algorithms. It is expected by mainstream theories that heat conduction in such 2D lattices is divergent and the thermal conductivity κ increases with lattice length N logarithmically. Our simulations for the purely quartic lattice firmly confirm it. However, very robust finite-size effects are observed in the calculations for the other two lattices, which well explain some existing studies and imply the extreme difficulties in observing their true asymptotic behaviors with affordable computation resources.

  5. Thermal Crosslinking of Organic Semiconducting Polythiophene Improves Transverse Hole Conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Gearba, I.R.; Nam, C.-Y.; Pindak, R.; Black, C.T.

    2009-10-26

    Thermal crosslinking using a suitable radical initiator simultaneously improves electrical conductivity in the semiconducting polymer poly(3-hexylthiophene) and makes the material insoluble. Crosslinked polythiophene shows as much as a fivefold increase in hole conductivity across the film thickness without any shift in spectral light absorption. Grazing incidence x-ray diffraction reveals more in-plane polymer lamellae stacking with only a small decrease in film crystallinity. Improved transverse conductivity increases the performance of model planar solar cells by threefold, from 0.07% to 0.2%. The ability to render polythiophene insoluble without disrupting film structural order enables fabrication pathways to more complex device architectures.

  6. Thermal crosslinking of organic semiconducting polythiophene improves transverse hole conductivity

    Science.gov (United States)

    Gearba, Ioana R.; Nam, Chang-Yong; Pindak, Ron; Black, C. T.

    2009-10-01

    Thermal crosslinking using a suitable radical initiator simultaneously improves electrical conductivity in the semiconducting polymer poly(3-hexylthiophene) and makes the material insoluble. Crosslinked polythiophene shows as much as a fivefold increase in hole conductivity across the film thickness without any shift in spectral light absorption. Grazing incidence x-ray diffraction reveals more in-plane polymer lamellae stacking with only a small decrease in film crystallinity. Improved transverse conductivity increases the performance of model planar solar cells by threefold, from 0.07% to 0.2%. The ability to render polythiophene insoluble without disrupting film structural order enables fabrication pathways to more complex device architectures.

  7. Thermal conductivity of single crystal and ceramic AlN

    Science.gov (United States)

    AlShaikhi, A.; Srivastava, G. P.

    2008-04-01

    We have applied the Callaway theory and used a detailed account of three-phonon scattering processes to calculate the thermal conductivity of three AlN single crystal samples containing different amounts of oxygen and two AlN ceramic samples with different grain sizes and oxygen contamination levels. The N-drift contribution to the total conductivity has been quantified. The influence on the thermal conductivity of oxygen-related defects, and grain boundaries in ceramic samples, has been investigated. The theoretical results obtained from this work are in good agreement with available experimental data. Our calculations suggest that the "effective" boundary length is greater than the reported grain size for each of the two ceramic samples studied by Watari et al. [J. Mater. Res. 17, 2940 (2002)].

  8. Experimental Investigations on Thermal Conductivity of Fenugreek and Banana Composites

    Science.gov (United States)

    Pujari, Satish; Venkatesh, Talari; Seeli, Hepsiba

    2017-06-01

    The use of composite materials in manufacturing has significantly increased in the past decade. Research is being done to identify natural fibers that can be used as composites. Several natural fibers are already being used in the industry as composites. The appealing advantages of using natural fibers are reflected in lower density when compared to synthetic fibers and also in saving costs. This research paper highlights the experiment that analyses the use of biodegradable fenugreek composite as natural fiber and concludes that fenugreek natural fibers are an excellent substitute to the synthetic fibers in terms of reinforcement properties for the polymers. These fenugreek fibers are naturally sourced, renewable, cost effective and bio-friendly. In thermal energy storage systems as well as in air conditioning systems, thermal insulators are predominantly used to enhance the storage properties. An experiment was created to investigate the thermal properties of fenugreek banana composites for different fiber concentrations. The experimental results showed that the thermal conductivity of the composites decrease with an increase in the fiber content. The experimental results were compared with the theoretical models to describe the variation of thermal conductivity with the volume fraction of the fiber. Good agreement between theoretical and experimental results was observed.

  9. Measurement of thermal conductivity and thermal diffusivity using a thermoelectric module

    Science.gov (United States)

    Beltrán-Pitarch, Braulio; Márquez-García, Lourdes; Min, Gao; García-Cañadas, Jorge

    2017-04-01

    A proof of concept of using a thermoelectric module to measure both thermal conductivity and thermal diffusivity of bulk disc samples at room temperature is demonstrated. The method involves the calculation of the integral area from an impedance spectrum, which empirically correlates with the thermal properties of the sample through an exponential relationship. This relationship was obtained employing different reference materials. The impedance spectroscopy measurements are performed in a very simple setup, comprising a thermoelectric module, which is soldered at its bottom side to a Cu block (heat sink) and thermally connected with the sample at its top side employing thermal grease. Random and systematic errors of the method were calculated for the thermal conductivity (18.6% and 10.9%, respectively) and thermal diffusivity (14.2% and 14.7%, respectively) employing a BCR724 standard reference material. Although errors are somewhat high, the technique could be useful for screening purposes or high-throughput measurements at its current state. This new method establishes a new application for thermoelectric modules as thermal properties sensors. It involves the use of a very simple setup in conjunction with a frequency response analyzer, which provides a low cost alternative to most of currently available apparatus in the market. In addition, impedance analyzers are reliable and widely spread equipment, which facilities the sometimes difficult access to thermal conductivity facilities.

  10. Thermal resistance optimization of GaN/substrate stacks considering thermal boundary resistance and temperature-dependent thermal conductivity

    Science.gov (United States)

    Park, K.; Bayram, C.

    2016-10-01

    Here, we investigate the effects of thermal boundary resistance (TBR) and temperature-dependent thermal conductivity on the thermal resistance of GaN/substrate stacks. A combination of parameters such as substrates {diamond, silicon carbide, silicon, and sapphire}, thermal boundary resistance {10-60 m2K/GW}, heat source lengths {10 nm-20 μm}, and power dissipation levels {1-8 W} are studied by using technology computer-aided design (TCAD) software Synopsys. Among diamond, silicon carbide, silicon, and sapphire substrates, the diamond provides the lowest thermal resistance due to its superior thermal conductivity. We report that due to non-zero thermal boundary resistance and localized heating in GaN-based high electron mobility transistors, an optimum separation between the heat source and substrate exists. For high power (i.e., 8 W) heat dissipation on high thermal conductive substrates (i.e., diamond), the optimum separation between the heat source and substrate becomes submicron thick (i.e., 500 nm), which reduces the hotspot temperature as much as 50 °C compared to conventional multi-micron thick case (i.e., 4 μm). This is attributed to the thermal conductivity drop in GaN near the heat source. Improving the TBR between GaN and diamond increases temperature reduction by our further approach. Overall, we provide thermal management design guidelines for GaN-based devices.

  11. Copper-based conductive composites with tailored thermal expansion.

    Science.gov (United States)

    Della Gaspera, Enrico; Tucker, Ryan; Star, Kurt; Lan, Esther H; Ju, Yongho Sungtaek; Dunn, Bruce

    2013-11-13

    We have devised a moderate temperature hot-pressing route for preparing metal-matrix composites which possess tunable thermal expansion coefficients in combination with high electrical and thermal conductivities. The composites are based on incorporating ZrW2O8, a material with a negative coefficient of thermal expansion (CTE), within a continuous copper matrix. The ZrW2O8 enables us to tune the CTE in a predictable manner, while the copper phase is responsible for the electrical and thermal conductivity properties. An important consideration in the processing of these materials is to avoid the decomposition of the ZrW2O8 phase. This is accomplished by using relatively mild hot-pressing conditions of 500 °C for 1 h at 40 MPa. To ensure that these conditions enable sintering of the copper, we developed a synthesis route for the preparation of Cu nanoparticles (NPs) based on the reduction of a common copper salt in aqueous solution in the presence of a size control agent. Upon hot pressing these nanoparticles at 500 °C, we are able to achieve 92-93% of the theoretical density of copper. The resulting materials exhibit a CTE which can be tuned between the value of pure copper (16.5 ppm/°C) and less than 1 ppm/°C. Thus, by adjusting the relative amount of the two components, the properties of the composite can be designed so that a material with high electrical conductivity and a CTE that matches the relatively low CTE values of semiconductor or thermoelectric materials can be achieved. This unique combination of electrical and thermal properties enables these Cu-based metal-matrix composites to be used as electrical contacts to a variety of semiconductor and thermoelectric devices which offer stable operation under thermal cycling conditions.

  12. Thermal Conductivity of Polymer/Nano-filler Blends

    Science.gov (United States)

    Ghose, Sayata; Watson, Kent A.; Delozier, Donovan M.; Working, Dennis C.; Connell, John W.; Smith, Joseph G.; Sun, Y. P.; Lin, Y.

    2006-01-01

    To improve the thermal conductivity of an ethylene vinyl acetate copolymer, Elvax 260 was compounded with three carbon based nano-fillers. Multiwalled carbon nanotubes (MWCNT), vapor grown carbon nanofibers (CNF) and expanded graphite (EG) were investigated. In an attempt to improve compatibility between the Elvax and nanofillers, MWCNTs and EGs were modified through non covalent and covalent attachment of alkyl groups. Ribbons were extruded to form samples in which the nanofillers were aligned, and samples were also fabricated by compression molding in which the nano-fillers were randomly oriented. The thermal properties were evaluated by DSC and TGA, and mechanical properties of the aligned samples were determined by tensile testing. The degree of dispersion and alignment of the nanoparticles were investigated using high-resolution scanning electron microscopy. Thermal conductivity measurements were performed using a Nanoflash technique. The thermal conductivity of the samples was measured in both the direction of alignment as well as perpendicular to that direction. The results of this study will be presented.

  13. Thermal conductivity of wool and wool-hemp insulation

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Z.; Wells, C.M.; Carrington, C.G. [University of Otago, Dunedin (New Zealand). Dept. of Physics; Hewitt, N.J. [University of Ulster, Jordanstown (United Kingdom). Centre for Sustainable Technologies

    2006-01-15

    Measurements have been obtained for the thermal resistance of sheep-wool insulation and wool-hemp mixtures, both in the form of bonded insulation batts, using a calibrated guarded hot-box. The density was 9.6-25.9 kg m{sup -3} for the wool and 9.9-18.1 kg m{sup -3} for the wool-hemp mixtures. The measurements were made at a mean sample temperature of 13.3{sup o}C using a calibrated guarded hot-box. The estimated uncertainly in the resistance measurements was of the order of {+-}7%. The thermal conductivity of the samples, derived from the thermal resistance measurements on the basis of the measured thickness, was well correlated with the density, although the variation with density was larger than that obtained in previous studies. The conductivity of the wool-hemp samples was not significantly different from that of the wool samples at the same density. Moisture uptake produced an increase of less than 5% in the conductivity of the bonded wool insulation for an increase in absorbed moisture content of 20%. The thermal resistance was 1.6% lower on average for samples oriented in the horizontal plane rather than the vertical plane, but this difference is not significant. (author)

  14. Effects of Doping on Thermal Conductivity of Pyrochlore Oxides for Advanced Thermal Barrier Coatings

    Science.gov (United States)

    Bansal, Narottam P.; Zhu, Dongming; Eslamloo-Grami, Maryam

    2006-01-01

    Pyrochlore oxides of general composition, A2B2O7, where A is a 3(+) cation (La to Lu) and B is a 4(+) cation (Zr, Hf, Ti, etc.) have high melting point, relatively high coefficient of thermal expansion, and low thermal conductivity which make them suitable for applications as high-temperature thermal barrier coatings. The effect of doping at the A site on the thermal conductivity of a pyrochlore oxide La2Zr2O7, has been investigated. Oxide powders of various compositions La2Zr2O7, La(1.7)Gd(0.3)Zr2O7, La(1.7)Yb(0.3)Zr2O7 and La(1.7)Gd(0.15)Yb(0.15)Zr2O7 were synthesized by the citric acid sol-gel method. These powders were hot pressed into discs and used for thermal conductivity measurements using a steady-state laser heat flux test technique. The rare earth oxide doped pyrochlores La(1.7)Gd(0.3)Zr2O7, La(1.7)Yb(0.3)Zr2O7 and La(1.7)Gd(0.15)Yb(0.15)Zr2O7 had lower thermal conductivity than the un-doped La2Zr2O7. The Gd2O3 and Yb2O3 co-doped composition showed the lowest thermal conductivity.

  15. Thermal conductivity of a film of single walled carbon nanotubes measured with infrared thermal imager

    Science.gov (United States)

    Feng, Ya; Inoue, Taiki; Xiang, Rong; Chiashi, Shohei; Maruyama, Shigeo

    Heat dissipation has restricted the modern miniaturization trend with the development of electronic devices. Theoretically proven to be with high axial thermal conductivity, single walled carbon nanotubes (SWNT) have long been expected to cool down the nanoscale world. Even though the tube-tube contact resistance limits the capability of heat transfer of the bulk film, the high intrinsic thermal conductivity of SWNT still glorify the application of films of SWNT network as a thermal interface material. In this work, we proposed a new method to straightly measure the thermal conductivity of SWNT film. We bridged two cantilevered Si thin plate with SWNT film, and kept a steady state heat flow in between. With the infrared camera to record the temperature distribution, the Si plates with known thermal conductivity can work as a reference to calculate the heat flux going through the SWNT film. Further, the thermal conductivity of the SWNT film can be obtained through Fourier's law after deducting the effect of thermal radiation. The sizes of the structure, the heating temperature, the vacuum degree and other crucial impact factors are carefully considered and analyzed. The author Y. F. was supported through the Advanced Integration Science Innovation Education and Research Consortium Program by the Ministry of Education, Culture, Sport, Science and Technology.

  16. Electrical and Thermal View Points for Designing Conduction-Cooled Specimen Holder for Short Sample Testing

    Science.gov (United States)

    Järvelä, J.; Stenvall, A.; Mikkonen, R.

    Theelectrical and stabilitypropertiesof superconductivestrandsareoftencharacterizedby short sample testing.These tests are often done in a measurement system where the sample is cooled by liquid cryogen or cold gas flow. In both approaches, the sample temperature during a measurement is stabilized by the abundance of available cooling power. This also helps to protect the sample during a thermal runaway i.e. quench. However, in some characterizations, e.g. minimum quench energy testing, the cooling conditions can have a significant effect on the results. Therefore a more adiabatic solution is prefer able as iten able seasier comparison of the results from different measurement stations. One solution to achieving the desired adiabacy is to use conduction-cooling and vacuum insulation. As there is no cooling fluidtorelyon, as cheme for sample protection has to be implemented. Inaconduction-cooled setup, one way to protect the sampleis to use an active protection system in conjunction with aproperly designed sample holder. In this publication, we present an electrical and thermal analysis of a conduction-cooled sample holder suitable for both critical current and minimum quench energy measurements. A coupled electro-thermal finite element method model was constructed to study the sample holder performance during measurement. For our application, the performance is defined by the ohmic losses in the holder component sand by the recovery time from as amplequench.

  17. Measuring thermal conductivity of powders with differential scanning calorimetry

    OpenAIRE

    Pujula, Miquel; Sánchez-Rodríguez, Daniel; López-Olmedo, Joan Pere; Farjas Silva, Jordi; Roura Grabulosa, Pere

    2016-01-01

    This paper simplifies a recently proposed method for measuring the thermal conductivity of powders using differential scanning calorimetry (DSC) (Sa´nchez-Rodríguez et al. in J Therm Anal Calorim 121:469-473, 2015). With this method, a crucible is filled with powder and a spherical metal reference is partially sunk into it. The thermal resistance between the metal and the crucible wall at the metal melting point is obtained from the DSC melting peak slope. In the simplified method outlined in...

  18. Thermal conductivity of one-dimensional Fibonacci quasicrystals

    Science.gov (United States)

    Maciá, Enrique

    2000-03-01

    We consider a general Fibonacci quasicrystal (FQC) in which both the masses and the elastic constants are aperiodically arranged. Making use of a suitable decimation scheme, inspired by real-space renormalization-group concepts, we obtain closed analytical expressions for the global transfer matrix and transmission coefficient for several resonant critical normal modes. The fractal structure of the frequency spectrum significantly influences both the cumulative contribution of the different normal modes to the thermal transport and the dependence of the thermal conductivity with the temperature over a wide temperature range. The role of resonant effects in the heat transport through the FQC is numerically and analytically discussed.

  19. Instrument for Measuring Thermal Conductivity of Materials at Low Temperatures

    Science.gov (United States)

    Fesmire, James; Sass, Jared; Johnson, Wesley

    2010-01-01

    With the advance of polymer and other non-metallic material sciences, whole new series of polymeric materials and composites are being created. These materials are being optimized for many different applications including cryogenic and low-temperature industrial processes. Engineers need these data to perform detailed system designs and enable new design possibilities for improved control, reliability, and efficiency in specific applications. One main area of interest is cryogenic structural elements and fluid handling components and other parts, films, and coatings for low-temperature application. An important thermal property of these new materials is the apparent thermal conductivity (k-value).

  20. Effects of thermal efficiency in DCMD and the preparation of membranes with low thermal conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Li, Zhehao, E-mail: ccgri_lzh@163.com [Changchun Gold Research Institute, 130012 (China); Peng, Yuelian, E-mail: pyl@live.com.au [Department of Chemistry and Chemical Engineering, College of Environmental and Energy Engineering, Beijing University of Technology, Beijing 100124 (China); Dong, Yajun; Fan, Hongwei [Department of Chemistry and Chemical Engineering, College of Environmental and Energy Engineering, Beijing University of Technology, Beijing 100124 (China); Chen, Ping [The Research Institute of Environmental Protection, North China Pharmaceutical Group Corporation, 050015 (China); Qiu, Lin [Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190 (China); Jiang, Qi [National Major Science and Technology Program Management Office for Water Pollution Control and Treatment, MEP, 100029 (China)

    2014-10-30

    Highlights: • The effects on vapor flux and thermal efficiency were simulated. • The conditions favoring vapor flux also favored thermal efficiency. • Four microporous polymer membranes were compared. • The SiO{sub 2} aerogel coating reduced the thermal conductivity of polymer membranes. • A 3ω technique was used to measure the thermal conductivity of membranes. - Abstract: The effects of the membrane characteristics and operational conditions on the vapor flux and thermal efficiency in a direct contact membrane distillation (DCMD) process were studied with a mathematical simulation. The membrane temperature, driving force of vapor transfer, membrane distillation coefficient, etc. were used to analyze the effects. The operating conditions that increased the vapor flux improved the thermal efficiency. The membrane characteristics of four microporous membranes and their performances in DCMD were compared. A polysulfone (PSf) membrane prepared via vapor-induced phase separation exhibited the lowest thermal conductivity. The PSf and polyvinylidene difluoride (PVDF) membranes were modified using SiO{sub 2} aerogel blending and coating to reduce the thermal conductivity of the membrane. The coating process was more effective than the blending process toward this end. The changes in the structure of the modified membrane were observed with a scanning electron microscope. Si was found on the modified membrane surface with an energy spectrometer. The PVDF composite and support membranes were tested during the DCMD process; the composite membrane had a higher vapor flux and a better thermal efficiency than the support. A new method based on a 3ω technique was used to measure the thermal conductivity of the membranes.

  1. Simultaneous Measurement of Thermal Diffusivity and Thermal Conductivity by Means of Inverse Solution for One-Dimensional Heat Conduction (Anisotropic Thermal Properties of CFRP for FCEV)

    Science.gov (United States)

    Kosaka, Masataka; Monde, Masanori

    2015-11-01

    For safe and fast fueling of hydrogen in a fuel cell electric vehicle at hydrogen fueling stations, an understanding of the heat transferred from the gas into the tank wall (carbon fiber reinforced plastic (CFRP) material) during hydrogen fueling is necessary. Its thermal properties are needed in estimating heat loss accurately during hydrogen fueling. The CFRP has anisotropic thermal properties, because it consists of an adhesive agent and layers of the CFRP which is wound with a carbon fiber. In this paper, the thermal diffusivity and thermal conductivity of the tank wall material were measured by an inverse solution for one-dimensional unsteady heat conduction. As a result, the thermal diffusivity and thermal conductivity were 2.09 × 10^{-6}{ m}2{\\cdot }{s}^{-1} and 3.06{ W}{\\cdot }{m}{\\cdot }^{-1}{K}^{-1} for the axial direction, while they were 6.03 × 10^{-7} {m}2{\\cdot }{s}^{-1} and 0.93 {W}{\\cdot }{m}^{-1}{\\cdot }{K}^{-1} for the radial direction. The thermal conductivity for the axial direction was about three times higher than that for the radial direction. The thermal diffusivity shows the same trend in both directions because the thermal capacity, ρ c, is independent of direction, where ρ is the density and c is the heat capacity.

  2. Two-temperature radiative shocks with electron thermal conduction

    Science.gov (United States)

    Borkowski, Kazimierz J.; Shull, J. Michael; Mckee, Christopher F.

    1989-01-01

    The influence of electron thermal conduction on radiative shock structure is studied for both one- and two-temperature plasmas. The dimensionless ratio of the conductive length to the cooling length determines whether or not conduction is important, and shock jump conditions with conduction are established for a collisionless shock front. Approximate solutions are obtained, with the assumptions that the ionization state of the gas is constant and the cooling rate is a function of temperature alone. In the absence of magnetic fields, these solutions indicate that conduction noticeably influences normal-abundance interstellar shocks with velocities 50-100 km/s and dramatically affects metal-dominated shocks over a wide range of shock velocities.

  3. Thermal conductivity measurements of proton-heated warm dense matter

    Science.gov (United States)

    McKelvey, A.; Fernandez-Panella, A.; Hua, R.; Kim, J.; King, J.; Sio, H.; McGuffey, C.; Kemp, G. E.; Freeman, R. R.; Beg, F. N.; Shepherd, R.; Ping, Y.

    2015-06-01

    Accurate knowledge of conductivity characteristics in the strongly coupled plasma regime is extremely important for ICF processes such as the onset of hydrodynamic instabilities, thermonuclear burn propagation waves, shell mixing, and efficient x-ray conversion of indirect drive schemes. Recently, an experiment was performed on the Titan laser platform at the Jupiter Laser Facility to measure the thermal conductivity of proton-heated warm dense matter. In the experiment, proton beams generated via target normal sheath acceleration were used to heat bi-layer targets with high-Z front layers and lower-Z back layers. The stopping power of a material is approximately proportional to Z2 so a sharp temperature gradient is established between the two materials. The subsequent thermal conduction from the higher-Z material to the lower-Z was measured with time resolved streaked optical pyrometry (SOP) and Fourier domain interferometry (FDI) of the rear surface. Results will be used to compare predictions from the thermal conduction equation and the Wiedemann-Franz Law in the warm dense matter regime. Data from the time resolved diagnostics for Au/Al and Au/C Targets of 20-200 nm thickness will be presented.

  4. Thermal shock problem of a generalized thermoelastic layered composite material with variable thermal conductivity

    Directory of Open Access Journals (Sweden)

    2006-01-01

    Full Text Available The dynamic treatment of one-dimensional generalized thermoelastic problem of heat conduction is made for a layered thin plate which is exposed to a uniform thermal shock taking into account variable thermal conductivity. The basic equations are transformed by Laplace transform and solved by a direct method. The solution was applied for a plate of sandwich structure, which is thermally shocked, and is traction-free in the outer sides. The inverses of Laplace transforms are obtained numerically. The temperature, the stress, and the displacement distributions are represented graphically.

  5. Thermal - Hydraulic Behavior of Unsaturated Bentonite and Sand-Bentonite Material as Seal for Nuclear Waste Repository: Numerical Simulation of Column Experiments

    Science.gov (United States)

    Ballarini, E.; Graupner, B.; Bauer, S.

    2015-12-01

    For deep geological repositories of high-level radioactive waste (HLRW), bentonite and sand bentonite mixtures are investigated as buffer materials to form a a sealing layer. This sealing layer surrounds the canisters and experiences an initial drying due to the heat produced by HLRW and a successive re-saturation with fluid from the host rock. These complex thermal, hydraulic and mechanical processes interact and were investigated in laboratory column experiments using MX-80 clay pellets as well as a mixture of 35% sand and 65% bentonite. The aim of this study is to both understand the individual processes taking place in the buffer materials and to identify the key physical parameters that determine the material behavior under heating and hydrating conditions. For this end, detailed and process-oriented numerical modelling was applied to the experiments, simulating heat transport, multiphase flow and mechanical effects from swelling. For both columns, the same set of parameters was assigned to the experimental set-up (i.e. insulation, heater and hydration system), while the parameters of the buffer material were adapted during model calibration. A good fit between model results and data was achieved for temperature, relative humidity, water intake and swelling pressure, thus explaining the material behavior. The key variables identified by the model are the permeability and relative permeability, the water retention curve and the thermal conductivity of the buffer material. The different hydraulic and thermal behavior of the two buffer materials observed in the laboratory observations was well reproduced by the numerical model.

  6. Effective Thermal Conductivity Modeling of Sandstones: SVM Framework Analysis

    Science.gov (United States)

    Rostami, Alireza; Masoudi, Mohammad; Ghaderi-Ardakani, Alireza; Arabloo, Milad; Amani, Mahmood

    2016-06-01

    Among the most significant physical characteristics of porous media, the effective thermal conductivity (ETC) is used for estimating the thermal enhanced oil recovery process efficiency, hydrocarbon reservoir thermal design, and numerical simulation. This paper reports the implementation of an innovative least square support vector machine (LS-SVM) algorithm for the development of enhanced model capable of predicting the ETCs of dry sandstones. By means of several statistical parameters, the validity of the presented model was evaluated. The prediction of the developed model for determining the ETCs of dry sandstones was in excellent agreement with the reported data with a coefficient of determination value ({R}2) of 0.983 and an average absolute relative deviation of 0.35 %. Results from present research show that the proposed LS-SVM model is robust, reliable, and efficient in calculating the ETCs of sandstones.

  7. Measurement of interfacial thermal conductance in Lithium ion batteries

    Science.gov (United States)

    Gaitonde, Aalok; Nimmagadda, Amulya; Marconnet, Amy

    2017-03-01

    Increasing usage and recent accidents due to Lithium ion (Li-ion) batteries exploding or catching on fire has inspired research on the thermal management of these batteries. In cylindrical 18650 cells, heat generated during the charge/discharge cycle must dissipate to the surrounding through its metallic case due to the poor thermal conductivity of the jelly roll, which is spirally wound with many interfaces between electrodes and the polymeric separator. This work develops a technique to measure the thermal resistance across the case-separator interface, which ultimately limits heat transfer out of the jelly roll. Commercial 18650 batteries are discharged and opened using a battery disassembly tool, and the 25 μm thick separator and the 200 μm thick metallic case are harvested to make samples. A miniaturized version of the conventional reference bar method

  8. Permeability and effective thermal conductivity of bisized porous media

    Energy Technology Data Exchange (ETDEWEB)

    Dias, Ricardo P. [Departamento de Tecnologia Quimica, Escola Superior de Tecnologia e de Gestao, Instituto Politecnico de Braganca, Campus de Santa Apolonia, Apartado 134, 5301-857 Braganca (Portugal); Fernandes, Carla S. [Departamento de Matematica, Escola Superior de Tecnologia e de Gestao, Instituto Politecnico de Braganca, Campus de Santa Apolonia, Apartado 134, 5301-857 Braganca (Portugal); Mota, Manuel; Teixeira, Jose A.; Yelshin, Alexander [Centro de Eng. Biologica, Universidade do Minho, Campus de Gualtar, 4710-057 Braga (Portugal)

    2007-04-15

    In the region of minimum porosity of particulate binary mixtures, heat exchange and permeability were found to be higher than the ones obtained with a mono-size packing built with the same small size particles used in the binary packing. This effect was noticed in the range of the particles size ratio 0.1-1.0. The obtained improvement on thermal performance is related to the increase of effective thermal conductivity (ETC) in the binary packing and to the increase in transversal thermal dispersion due to the porosity decrease and tortuosity increase. Permeability can increase by a factor of two, if the size ratio between small and large spheres of a loose packing stays in the range 0.3-0.5. (author)

  9. Low conductivity and sintering-resistant thermal barrier coatings

    Science.gov (United States)

    Zhu, Dongming (Inventor); Miller, Robert A. (Inventor)

    2007-01-01

    A thermal barrier coating composition is provided. The composition has a base oxide, a primary stabilizer, and at least two additional cationic oxide dopants. Preferably, a pair of group A and group B defect cluster-promoting oxides is used in conjunction with the base and primary stabilizer oxides. The new thermal barrier coating is found to have significantly lower thermal conductivity and better sintering resistance. In preferred embodiments, the base oxide is selected from zirconia and hafnia. The group A and group B cluster-promoting oxide dopants preferably are selected such that the group A dopant has a smaller cationic radius than the primary stabilizer oxide, and so that the primary stabilizer oxide has a small cationic radius than that of the group B dopant.

  10. Applications of high thermal conductivity composites to electronics and spacecraft thermal design

    Science.gov (United States)

    Sharp, G. Richard; Loftin, Timothy A.

    1990-01-01

    Recently, high thermal conductivity graphite fiber-reinforced metal matrix composites (MMCs) have become available that can save weight over present methods of heat conduction. Another significant advantage is that these materials can be used without the plumbing and testing complexities that accompany the use of liquid heat pipes. A spinoff of this research was the development of other MMCs as electronic device heat sinks. These use particulates rather than fibers and are formulated to match the coefficient of thermal expansion of electronic substrates in order to alleviate thermally induced stresses. The development of both types of these materials as viable weight-saving substitutes for the traditional methods of thermal control for electronics packaging and also for spacecraft thermal control applications are the subjects of this report.

  11. Thermal rectification and negative differential thermal conductance in harmonic chains with nonlinear system-bath coupling.

    Science.gov (United States)

    Ming, Yi; Li, Hui-Min; Ding, Ze-Jun

    2016-03-01

    Thermal rectification and negative differential thermal conductance were realized in harmonic chains in this work. We used the generalized Caldeira-Leggett model to study the heat flow. In contrast to most previous studies considering only the linear system-bath coupling, we considered the nonlinear system-bath coupling based on recent experiment [Eichler et al., Nat. Nanotech. 6, 339 (2011)]. When the linear coupling constant is weak, the multiphonon processes induced by the nonlinear coupling allow more phonons transport across the system-bath interface and hence the heat current is enhanced. Consequently, thermal rectification and negative differential thermal conductance are achieved when the nonlinear couplings are asymmetric. However, when the linear coupling constant is strong, the umklapp processes dominate the multiphonon processes. Nonlinear coupling suppresses the heat current. Thermal rectification is also achieved. But the direction of rectification is reversed compared to the results of weak linear coupling constant.

  12. Thermal rectification and negative differential thermal conductance in harmonic chains with nonlinear system-bath coupling

    Science.gov (United States)

    Ming, Yi; Li, Hui-Min; Ding, Ze-Jun

    2016-03-01

    Thermal rectification and negative differential thermal conductance were realized in harmonic chains in this work. We used the generalized Caldeira-Leggett model to study the heat flow. In contrast to most previous studies considering only the linear system-bath coupling, we considered the nonlinear system-bath coupling based on recent experiment [Eichler et al., Nat. Nanotech. 6, 339 (2011), 10.1038/nnano.2011.71]. When the linear coupling constant is weak, the multiphonon processes induced by the nonlinear coupling allow more phonons transport across the system-bath interface and hence the heat current is enhanced. Consequently, thermal rectification and negative differential thermal conductance are achieved when the nonlinear couplings are asymmetric. However, when the linear coupling constant is strong, the umklapp processes dominate the multiphonon processes. Nonlinear coupling suppresses the heat current. Thermal rectification is also achieved. But the direction of rectification is reversed compared to the results of weak linear coupling constant.

  13. Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids

    Directory of Open Access Journals (Sweden)

    Cieśliński Janusz T.

    2015-12-01

    Full Text Available In this study the results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e., thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1%, and 5% by weight within temperature range from 20 °C to 60 °C. Measurement devices were carefully calibrated by comparison obtained results for pure base liquid (thermal oil with manufacturer’s data. The results obtained for tested nanofluids were compared with predictions made by use of existing models for liquid/solid particles mixtures.

  14. Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids

    Science.gov (United States)

    Cieśliński, Janusz T.; Ronewicz, Katarzyna; Smoleń, Sławomir

    2015-12-01

    In this study the results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e., thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1%, and 5% by weight within temperature range from 20 °C to 60 °C. Measurement devices were carefully calibrated by comparison obtained results for pure base liquid (thermal oil) with manufacturer's data. The results obtained for tested nanofluids were compared with predictions made by use of existing models for liquid/solid particles mixtures.

  15. Thermal conductivity, viscosity, and electrical conductivity of iron oxide with a cloud fractal structure

    Science.gov (United States)

    Jamilpanah, Pouya; Pahlavanzadeh, Hassan; Kheradmand, Amanj

    2016-09-01

    In the present study, nanoscale iron oxide was synthesized using a hydrothermal method; XRD analysis revealed that all the produced crystals are iron oxide. FESEM microscopic imaging showed that particles are on the scale of nano and their morphology is cloud fractal. To study the laboratory properties of thermal conductivity, viscosity, and electrical conductivity of the nanoparticles, they were dispersed in ethylene glycol-based fluid and the nanofluid was in a two-step synthesis during this process. The experiments were carried out with a weight fraction between 0 and 2 % at temperatures between 25 and 45 °C. According to the results of the experiments, increasing the density of nanoparticles in the fluid increases thermal conductivity, as it was predicted in all theoretical models. On the other hand, nano viscosity increases as the weight fraction increases while it decreases as temperature goes up. Electrical conductivity also increases with raising the temperature and weight fraction. Theoretical models were studied to predict Thermal conductivity, viscosity, and electrical conductivity of the nanofluid.

  16. Thermal conductivity, viscosity, and electrical conductivity of iron oxide with a cloud fractal structure

    Science.gov (United States)

    Jamilpanah, Pouya; Pahlavanzadeh, Hassan; Kheradmand, Amanj

    2017-04-01

    In the present study, nanoscale iron oxide was synthesized using a hydrothermal method; XRD analysis revealed that all the produced crystals are iron oxide. FESEM microscopic imaging showed that particles are on the scale of nano and their morphology is cloud fractal. To study the laboratory properties of thermal conductivity, viscosity, and electrical conductivity of the nanoparticles, they were dispersed in ethylene glycol-based fluid and the nanofluid was in a two-step synthesis during this process. The experiments were carried out with a weight fraction between 0 and 2 % at temperatures between 25 and 45 °C. According to the results of the experiments, increasing the density of nanoparticles in the fluid increases thermal conductivity, as it was predicted in all theoretical models. On the other hand, nano viscosity increases as the weight fraction increases while it decreases as temperature goes up. Electrical conductivity also increases with raising the temperature and weight fraction. Theoretical models were studied to predict Thermal conductivity, viscosity, and electrical conductivity of the nanofluid.

  17. Thermal contact conductance and thermal shield design for superconducting magnet systems

    Energy Technology Data Exchange (ETDEWEB)

    Nilles, M.J.; Lehmann, G.A. [Babcock and Wilcox, Lynchburg, VA (United States)

    1994-12-31

    The aluminum radiation shields in the SSC Quadrupole magnets are conductively cooled from the cryogen flow in the 80 K and 20 K flow circuits. As the shield temperature is very sensitive to the effective heat transfer rate between the shield-piping interface, the method of shield mounting and heat sinking is critical. Cost and reliability concerns also drive the design. Here, the authors discuss critical issues that can have a limiting effect on the shield thermal performance. The spring-type action of the shield clamps it in place and heat transfer across the interface depends on thermal contact conductance. Thermally induced stresses can be relieved by allowing the shield and piping to slide relative to each other. Test results are presented on stainless steel-aluminum thermal contact conductance and its effect on the shield performance is discussed.

  18. Effect of nanoparticle coating on the thermal conductivity of microporous thermal insulations.

    Science.gov (United States)

    Lee, Dong-Bok; Kwon, Hyuk-Chon; Kim, Yun-Il; Park, Sung; Lee, Jae Chun; Misture, Scott

    2010-05-01

    Microporous thermal insulations were prepared from mixtures of nano-sized fumed silica, micron-sized fibers and opacifier particles. Those micron-sized particles were dry coated with nano-sized fumed silica particles by mechanical process using a compressive-shear type mill. The effect of nanoparticle coating on the thermal conductivity of the insulation media was investigated using a hot-wire method. Effect of nanoparticle coating was found to be more pronounced for the insulation composed of fumed silica and fiber than for the one composed of fumed silica, fiber and an opacifier. By adding 15% SiC or TiO2 opacifier, the thermal conductivity of the insulation samples could be lowered to 0.08 Wm(-1) K(-1) at temperature range of 805 approximately 817 degrees C. The temperature dependent thermal conductivity of the sample containing glass fiber did not exhibit any remarkable changes compared to the one containing ceramic fiber.

  19. Thermal conductivity of isotopically modified graphene.

    Science.gov (United States)

    Chen, Shanshan; Wu, Qingzhi; Mishra, Columbia; Kang, Junyong; Zhang, Hengji; Cho, Kyeongjae; Cai, Weiwei; Balandin, Alexander A; Ruoff, Rodney S

    2012-01-10

    In addition to its exotic electronic properties graphene exhibits unusually high intrinsic thermal conductivity. The physics of phonons--the main heat carriers in graphene--has been shown to be substantially different in two-dimensional (2D) crystals, such as graphene, from in three-dimensional (3D) graphite. Here, we report our experimental study of the isotope effects on the thermal properties of graphene. Isotopically modified graphene containing various percentages of 13C were synthesized by chemical vapour deposition (CVD). The regions of different isotopic compositions were parts of the same graphene sheet to ensure uniformity in material parameters. The thermal conductivity, K, of isotopically pure 12C (0.01% 13C) graphene determined by the optothermal Raman technique, was higher than 4,000 W mK(-1) at the measured temperature T(m)~320 K, and more than a factor of two higher than the value of K in graphene sheets composed of a 50:50 mixture of 12C and 13C. The experimental data agree well with our molecular dynamics (MD) simulations, corrected for the long-wavelength phonon contributions by means of the Klemens model. The experimental results are expected to stimulate further studies aimed at a better understanding of thermal phenomena in 2D crystals.

  20. Thermal conductivity determination of cometary and asteroid material analogues

    Science.gov (United States)

    Banaszkiewicz, M.; Seweryn, K.; Wawrzaszek, R.

    Measurements of physical properties of surface and subsurface layers of planetary bodies often provide important information about the structure of the medium and processes that occur there Thermal properties of cometary nuclues subsurface material are crucial in determining the heat and gas transport Similarly asteroid s regolith is a buffering zone in heat transfer from to surface to from interior of a body There are space experiments planned to perform temperature and thermal conductivity measurements on a comet ROSETTA and one can easily foresee such measurements carried out by future robotic missions on Mars planetary satellites and asteroids In the paper we present the results of measurements carried out with a new type of thermal sensors The elementary cylindrical sensor is made of platinum wire resistance thermometer and isotan wire heating element that can operate independently By choosing these materials the problems of temperature measurement calibration and constant heating power are resolved We confront the results of measurements made for a number of sensors combined into a long cylinder in delrin basalt ice-dust mixture comet analogue and regolith-like material with models and show that agreement is very good Therefore we can recommend both the sensors and the method of data interpretation for the thermal conductivity determination as very useful tools in future space missions and in laboratory experiments on cometary and asteroid material analogues

  1. Prediction of the Effective Thermal Conductivity of Powder Insulation

    Science.gov (United States)

    Jin, Lingxue; Park, Jiho; Lee, Cheonkyu; Jeong, Sangkwon

    The powder insulation method is widely used in structural and cryogenic systems such as transportation and storage tanks of cryogenic fluids. The powder insulation layer is constructed by small particle powder with light weight and some residual gas with high porosity. So far, many experiments have been carried out to test the thermal performance of various kinds of powder, including expanded perlite, glass microspheres, expanded polystyrene (EPS). However, it is still difficult to predict the thermal performance of powder insulation by calculation due to the complicated geometries, including various particle shapes, wide powder diameter distribution, and various pore sizes. In this paper, the effective thermal conductivity of powder insulation has been predicted based on an effective thermal conductivity calculationmodel of porous packed beds. The calculation methodology was applied to the insulation system with expanded perlite, glass microspheres and EPS beads at cryogenic temperature and various vacuum pressures. The calculation results were compared with previous experimental data. Moreover, additional tests were carried out at cryogenic temperature in this research. The fitting equations of the deformation factor of the area-contact model are presented for various powders. The calculation results show agood agreement with the experimental results.

  2. Shocks and Thermal Conduction Fronts in Retracting Reconnected Flux Tubes

    CERN Document Server

    Guidoni, Silvina

    2010-01-01

    We present a model for plasma heating produced by time-dependent, spatially localized reconnection within a flare current sheet separating skewed magnetic fields. The reconnection creates flux tubes of new connectivity which subsequently retract at Alfv\\'enic speeds from the reconnection site. Heating occurs in gas-dynamic shocks which develop inside these tubes. Here we present generalized thin flux tube equations for the dynamics of reconnected flux tubes, including pressure-driven parallel dynamics as well as temperature dependent, anisotropic viscosity and thermal conductivity. The evolution of tubes embedded in a uniform, skewed magnetic field, following reconnection in a patch, is studied through numerical solutions of these equations, for solar coronal conditions. Even though viscosity and thermal conductivity are negligible in the quiet solar corona, the strong gas-dynamic shocks generated by compressing plasma inside reconnected flux tubes generate large velocity and temperature gradients along the t...

  3. Modeling of thermal conductivity of stainless-steelmaking dust pellets

    Institute of Scientific and Technical Information of China (English)

    彭兵; 彭及; 余笛

    2004-01-01

    The thermal conductivity of stainless-steelmaking dust pellets, an important parameter for the direct recycling of the dust, is naturally of interest to metallurgists. The measurement of central temperature and surface temperature was taken in a furnace. The physical model and calculation model for the heating process were set up to check the thermal conductivity of the dust pellets. The physical structure parameters δ and λ of the basic unit are 0.92 and 0.45 based on the calculation. The temperature in the pellet can be expressed in a linear equation a5 Tp =a1 TN +a2 TM +a4. This is convenient to determine the central temperature of a pellet in the direct recycling process.

  4. Lattice thermal conductivity of borophene from first principle calculation

    Science.gov (United States)

    Xiao, Huaping; Cao, Wei; Ouyang, Tao; Guo, Sumei; He, Chaoyu; Zhong, Jianxin

    2017-04-01

    The phonon transport property is a foundation of understanding a material and predicting the potential application in mirco/nano devices. In this paper, the thermal transport property of borophene is investigated by combining first-principle calculations and phonon Boltzmann transport equation. At room temperature, the lattice thermal conductivity of borophene is found to be about 14.34 W/mK (error is about 3%), which is much smaller than that of graphene (about 3500 W/mK). The contributions from different phonon modes are qualified, and some phonon modes with high frequency abnormally play critical role on the thermal transport of borophene. This is quite different from the traditional understanding that thermal transport is usually largely contributed by the low frequency acoustic phonon modes for most of suspended 2D materials. Detailed analysis further reveals that the scattering between the out-of-plane flexural acoustic mode (FA) and other modes likes FA + FA/TA/LA/OP ↔ TA/LA/OP is the predominant phonon process channel. Finally the vibrational characteristic of some typical phonon modes and mean free path distribution of different phonon modes are also presented in this work. Our results shed light on the fundamental phonon transport properties of borophene, and foreshow the potential application for thermal management community.

  5. Reference Correlations of the Thermal Conductivity of Ethene and Propene

    Science.gov (United States)

    Koutian, A.; Huber, M. L.; Perkins, R. A.

    2016-01-01

    New, wide-range reference equations for the thermal conductivity of ethene and propene as a function of temperature and density are presented. The equations are based in part upon a body of experimental data that has been critically assessed for internal consistency and for agreement with theory whenever possible. For ethene, we estimate the uncertainty (at the 95% confidence level) for the thermal conductivity from 110 K to 520 K at pressures up to 200 MPa to be 5% for the compressed liquid and supercritical phases. For the low-pressure gas phase (to 0.1 MPa) over the temperature range 270 K to 680 K, the estimated uncertainty is 4%. The correlation is valid from 110 K to 680 K and up to 200 MPa, but it behaves in a physically reasonable manner down to the triple point and may be used at pressures up to 300 MPa, although the uncertainty will be larger in regions where experimental data were unavailable. In the case of propene, data are much more limited. We estimate the uncertainty for the thermal conductivity of propene from 180 K to 625 K at pressures up to 50 MPa to be 5% for the gas, liquid, and supercritical phases. The correlation is valid from 180 K to 625 K and up to 50 MPa, but it behaves in a physically reasonable manner down to the triple point and may be used at pressures up to 100 MPa, although the uncertainty will be larger in regions where experimental data were unavailable. For both fluids, uncertainties in the critical region are much larger, since the thermal conductivity approaches infinity at the critical point and is very sensitive to small changes in density.

  6. Reference Correlations of the Thermal Conductivity of Ethene and Propene.

    Science.gov (United States)

    Assael, M J; Koutian, A; Huber, M L; Perkins, R A

    2016-09-01

    New, wide-range reference equations for the thermal conductivity of ethene and propene as a function of temperature and density are presented. The equations are based in part upon a body of experimental data that has been critically assessed for internal consistency and for agreement with theory whenever possible. For ethene, we estimate the uncertainty (at the 95% confidence level) for the thermal conductivity from 110 K to 520 K at pressures up to 200 MPa to be 5% for the compressed liquid and supercritical phases. For the low-pressure gas phase (to 0.1 MPa) over the temperature range 270 K to 680 K, the estimated uncertainty is 4%. The correlation is valid from 110 K to 680 K and up to 200 MPa, but it behaves in a physically reasonable manner down to the triple point and may be used at pressures up to 300 MPa, although the uncertainty will be larger in regions where experimental data were unavailable. In the case of propene, data are much more limited. We estimate the uncertainty for the thermal conductivity of propene from 180 K to 625 K at pressures up to 50 MPa to be 5% for the gas, liquid, and supercritical phases. The correlation is valid from 180 K to 625 K and up to 50 MPa, but it behaves in a physically reasonable manner down to the triple point and may be used at pressures up to 100 MPa, although the uncertainty will be larger in regions where experimental data were unavailable. For both fluids, uncertainties in the critical region are much larger, since the thermal conductivity approaches infinity at the critical point and is very sensitive to small changes in density.

  7. Electronic thermal conductivity in a superconducting vortex state

    Energy Technology Data Exchange (ETDEWEB)

    Adachi, H. [Department of Physics, Okayama University, Tsushima, Okayama 700-8530 (Japan)], E-mail: adachi@itp.phys.ethz.ch; Miranovic, P. [Department of Physics, University of Montenegro, Podgorica 81000 (Montenegro); Ichioka, M.; Machida, K. [Department of Physics, Okayama University, Tsushima, Okayama 700-8530 (Japan)

    2007-10-01

    The longitudinal component of the electronic thermal conductivity {kappa}{sub xx} in a superconducting vortex state is calculated as a function of magnetic field B. Calculations are performed by taking account of the spatial dependence of normal Green's function g, which was neglected in the previous studies using the Brandt-Pesch-Tewordt method. We discuss the possibility of using {kappa}{sub xx}(B) as a probe of the pair potential symmetry.

  8. Electronic thermal conductivity in a superconducting vortex state

    Science.gov (United States)

    Adachi, H.; Miranovic, P.; Ichioka, M.; Machida, K.

    2007-10-01

    The longitudinal component of the electronic thermal conductivity κxx in a superconducting vortex state is calculated as a function of magnetic field B. Calculations are performed by taking account of the spatial dependence of normal Green's function g, which was neglected in the previous studies using the Brandt-Pesch-Tewordt method. We discuss the possibility of using κxx(B) as a probe of the pair potential symmetry.

  9. Thermal Conductivity of the Potential Repository Horizon Model Report

    Energy Technology Data Exchange (ETDEWEB)

    J. Ramsey

    2002-08-29

    The purpose of this report is to assess the spatial variability and uncertainty of thermal conductivity in the host horizon for the proposed repository at Yucca Mountain. More specifically, the lithostratigraphic units studied are located within the Topopah Spring Tuff (Tpt) and consist of the upper lithophysal zone (Tptpul), the middle nonlithophysal zone (Tptpmn), the lower lithophysal zone (Tptpll), and the lower nonlithophysal zone (Tptpln). The Tptpul is the layer directly above the repository host layers, which consist of the Tptpmn, Tptpll, and the Tptpln. Current design plans indicate that the largest portion of the repository will be excavated in the Tptpll (Board et al. 2002 [157756]). The main distinguishing characteristic among the lithophysal and nonlithophysal units is the percentage of large scale (cm-m) voids within the rock. The Tptpul and Tptpll, as their names suggest, have a higher percentage of lithophysae than the Tptpmn and the Tptpln. Understanding the influence of the lithophysae is of great importance to understanding bulk thermal conductivity and perhaps repository system performance as well. To assess the spatial variability and uncertainty of thermal conductivity, a model is proposed that is functionally dependent on the volume fraction of lithophysae and the thermal conductivity of the matrix portion of the rock. In this model, void space characterized as lithophysae is assumed to be air-saturated under all conditions, while void space characterized as matrix may be either water- or air-saturated. Lithophysae are assumed to be air-saturated under all conditions since the units being studied are all located above the water table in the region of interest, and the relatively strong capillary forces of the matrix will, under most conditions, preferentially retain any moisture present in the rock.

  10. DESIGN AND FABRICATION OF THERMAL CONDUCTIVITY APPARATUS FOR CASHEW NUT

    OpenAIRE

    2016-01-01

    Experiments were conducted for determination of various physical properties of Vengurla-4 variety of cashew nut. The diameter or size and sphericity of cashew nut were found to be 21.92 mm and 0.68 respectively. The average gravimetric properties such as bulk density were found to be 533 kg/m3, true density were 663.3 kg/m3 and porosity were 19.6%. Angle of repose for cashew nut were found as 30.50.   Thermal conductivity of cashew nut were determined at different moisture conten...

  11. Thermal conductance of carbon nanotube contacts: Molecular dynamics simulations and general description of the contact conductance

    Science.gov (United States)

    Salaway, Richard N.; Zhigilei, Leonid V.

    2016-07-01

    The contact conductance of carbon nanotube (CNT) junctions is the key factor that controls the collective heat transfer through CNT networks or CNT-based materials. An improved understanding of the dependence of the intertube conductance on the contact structure and local environment is needed for predictive computational modeling or theoretical description of the effective thermal conductivity of CNT materials. To investigate the effect of local structure on the thermal conductance across CNT-CNT contact regions, nonequilibrium molecular dynamics (MD) simulations are performed for different intertube contact configurations (parallel fully or partially overlapping CNTs and CNTs crossing each other at different angles) and local structural environments characteristic of CNT network materials. The results of MD simulations predict a stronger CNT length dependence present over a broader range of lengths than has been previously reported and suggest that the effect of neighboring junctions on the conductance of CNT-CNT junctions is weak and only present when the CNTs that make up the junctions are within the range of direct van der Waals interaction with each other. A detailed analysis of the results obtained for a diverse range of intertube contact configurations reveals a nonlinear dependence of the conductance on the contact area (or number of interatomic intertube interactions) and suggests larger contributions to the conductance from areas of the contact where the density of interatomic intertube interactions is smaller. An empirical relation accounting for these observations and expressing the conductance of an arbitrary contact configuration through the total number of interatomic intertube interactions and the average number of interatomic intertube interactions per atom in the contact region is proposed. The empirical relation is found to provide a good quantitative description of the contact conductance for various CNT configurations investigated in the MD

  12. Design and Performance Optimizations of Advanced Erosion-Resistant Low Conductivity Thermal Barrier Coatings for Rotorcraft Engines

    Science.gov (United States)

    Zhu, Dongming; Miller, Robert A.; Kuczmarski, Maria A.

    2012-01-01

    Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future rotorcraft engine higher fuel efficiency and lower emission goals. For thermal barrier coatings designed for rotorcraft turbine airfoil applications, further improved erosion and impact resistance are crucial for engine performance and durability, because the rotorcraft are often operated in the most severe sand erosive environments. Advanced low thermal conductivity and erosion-resistant thermal barrier coatings are being developed, with the current emphasis being placed on thermal barrier coating toughness improvements using multicomponent alloying and processing optimization approaches. The performance of the advanced thermal barrier coatings has been evaluated in a high temperature erosion burner rig and a laser heat-flux rig to simulate engine erosion and thermal gradient environments. The results have shown that the coating composition and architecture optimizations can effectively improve the erosion and impact resistance of the coating systems, while maintaining low thermal conductivity and cyclic oxidation durability

  13. Increased Thermal Conductivity in Metal-Organic Heat Carrier Nanofluids

    Energy Technology Data Exchange (ETDEWEB)

    Nandasiri, Manjula I.; Liu, Jian; McGrail, B. Peter; Jenks, Jeromy WJ; Schaef, Herbert T.; Shutthanandan, V.; Nie, Zimin; Martin, Paul F.; Nune, Satish K.

    2016-06-15

    Metal organic heat carriers (MOHCs) are recently developed nanofluids containing metal organic framework (MOF) nanoparticles dispersed in various base fluids including refrigerants (R245Fa) and methanol. MOHCs utilize the MOF properties to improve the thermo-physical properties of base fluids. Here, we report the synthesis and characterization of MOHCs containing nanoMIL-101(Cr) and graphene oxide (GO) in an effort to improve the thermo-physical properties of various base fluids. MOHC containing MIL-101(Cr)/GO nanocomposites showed enhanced surface area, porosity, and nitrogen adsorption compared with the intrinsic nano MIL-101(Cr) and the properties depend on the amount of GO added. Powder X-ray diffraction (PXRD) confirmed the preserved crystallinity of MIL-101(Cr) in all nanocomposites with the absence of any unreacted GO. Scanning electron microscopy images confirmed the presence of near spherical MIL-101(Cr) nanoparticles in the range of 40-80 nm in diameter. MOHC nanofluids containing MIL-101(Cr)/GO in methanol exhibited significant enhancement in the thermal conductivity (by approxi-mately 50%) relative to that of the intrinsic nano MIL-101(Cr) in methanol. The thermal conductivity of base fluid (methanol) was enhanced by about 20 %. The enhancement in the thermal conductivity of nanoMIL-101(Cr) MOHCs due to graphene oxide functionalization is explained using a classical Maxwell model.

  14. Measurement of Thermal Conductivity of Liquids at High Temperature

    Science.gov (United States)

    Schick, V.; Remy, B.; Degiovanni, A.; Demeurie, F.; Meulemans, J.; Lombard, P.

    2012-11-01

    The goal purchased in this paper is to implement a pulse method to measure the thermal conductivity of liquid silica glass above 1200°C until 1600°C. A heat flux stimulation controlled in energy and in time is generated on the front face of an experimental cell. The temperature rise is measured on the rear face of this cell face by using a fast cooled infrared camera. The choice of the measurement cell geometry is fundamental to be able to estimate at the same time the thermal diffusivity and the specific heat of the liquid by an inverse technique. The parameters estimation problem takes into account the optimization of the cell wall thickness. The theoretical model used for the inversion takes into account the coupled heat transfer modes (conduction, convection and radiation) that can occur during the experiment, particularly the thermal conductive short-cut through metallic lateral walls of the cell and radiative transfer within the semi-transparent and participating medium. First measurements are performed on a cell filled with water at ambient temperature in order to validate the parameters estimation procedure.

  15. Pure-oxygen radiative shocks with electron thermal conduction

    Science.gov (United States)

    Borkowski, Kazimierz J.; Shull, J. Michael

    1990-01-01

    Steady state radiative shock models in gas composed entirely of oxygen are calculated with the purpose of explaining observations of fast-moving knots in Cas A and other oxygen-rich SNRs. Models with electron thermal conduction differ significantly from models in which conduction is neglected. Conduction reduces postshock electron temperatures by a factor of 7-10 and flattens temperature gradients. The O III ion, whose forbidden emission usually dominates the observed spectra, is present over a wide range of shock velocities, from 100 to 170 km/s. The electron temperature in the O III forbidden line formation region is 30,000 K, in agreement with the 20,000 K derived from observations. All models with conduction have extensive warm (T above 4000 K) photoionization zones, which provides better agreement with observed optical O I line strengths.

  16. Substrate-induced reduction of graphene thermal conductivity

    Science.gov (United States)

    Koniakhin, S. V.; Utesov, O. I.; Terterov, I. N.; Nalitov, A. V.

    2017-01-01

    We develop a theory of heat conductivity in supported graphene, accounting for coherent phonon scattering on disorder induced by an amorphous substrate. We derive spectra for in-plane and out-of-plane phonons in the framework of Green's function approach. The energy parameters of the theory are obtained using molecular dynamics simulations for graphene on a SiO2 substrate. The heat conductivity is calculated by the Boltzmann transport equation. We find that the interaction with the substrate drastically reduces the phonon lifetime and completely suppresses the contribution of flexural (ZA) phonons to the heat conductivity. As a result, the total heat conductivity is reduced by several times, which matches with the tendency observed in the available experimental data. The considered effect is important for managing the thermal properties of graphene-based electronic devices.

  17. Device and method for measuring thermal conductivity of thin films

    Science.gov (United States)

    Amer, Tahani R. (Inventor); Subramanian, Chelakara (Inventor); Upchurch, Billy T. (Inventor); Alderfer, David W. (Inventor); Sealey, Bradley S. (Inventor); Burkett, Jr., Cecil G. (Inventor)

    2001-01-01

    A device and method are provided for measuring the thermal conductivity of rigid or flexible, homogeneous or heterogeneous, thin films between 50 .mu.m and 150 .mu.m thick with relative standard deviations of less than five percent. The specimen is sandwiched between like material, highly conductive upper and lower slabs. Each slab is instrumented with six thermocouples embedded within the slab and flush with their corresponding surfaces. A heat source heats the lower slab and a heat sink cools the upper slab. The heat sink also provides sufficient contact pressure onto the specimen. Testing is performed within a vacuum environment (bell-jar) between 10.sup.-3 to 10.sup.-6 Torr. An anti-radiant shield on the interior surface of the bell-jar is used to avoid radiation heat losses. Insulation is placed adjacent to the heat source and adjacent to the heat sink to prevent conduction losses. A temperature controlled water circulator circulates water from a constant temperature bath through the heat sink. Fourier's one-dimensional law of heat conduction is the governing equation. Data, including temperatures, are measured with a multi-channel data acquisition system. On-line computer processing is used for thermal conductivity calculations.

  18. The Thermal Electrical Conductivity Probe (TECP) for Phoenix

    Science.gov (United States)

    Zent, Aaron P.; Hecht, Michael H.; Cobos, Doug R.; Campbell, Gaylon S.; Campbell, Colin S.; Cardell, Greg; Foote, Marc C.; Wood, Stephen E.; Mehta, Manish

    2009-01-01

    The Thermal and Electrical Conductivity Probe (TECP) is a component of the Microscopy, Electrochemistry, and Conductivity Analyzer (MECA) payload on the Phoenix Lander. TECP will measure the temperature, thermal conductivity and volumetric heat capacity of the regolith. It will also detect and quantify the population of mobile H2O molecules in the regolith, if any, throughout the polar summer, by measuring the electrical conductivity of the regolith, as well as the dielectric permittivity. In the vapor phase, TECP is capable of measuring the atmospheric H2O vapor abundance, as well as augment the wind velocity measurements from the meteorology instrumentation. TECP is mounted near the end of the 2.3 m Robotic Arm, and can be placed either in the regolith material or held aloft in the atmosphere. This paper describes the development and calibration of the TECP. In addition, substantial characterization of the instrument has been conducted to identify behavioral characteristics that might affect landed surface operations. The greatest potential issue identified in characterization tests is the extraordinary sensitivity of the TECP to placement. Small gaps alter the contact between the TECP and regolith, complicating data interpretation. Testing with the Phoenix Robotic Arm identified mitigation techniques that will be implemented during flight. A flight model of the instrument was also field tested in the Antarctic Dry Valleys during the 2007-2008 International Polar year. 2

  19. Ground ULV and thermal fog applications against Phlebotomine sand fly vectors of Leishmania in a hot arid environment in western Kenya

    Science.gov (United States)

    Phlebotomine sand fly vectors of Leishmania continue to threaten US military operations in Africa, Southwest Asia, and the Middle East. Ultra-low volume (ULV) and/or thermal fog pesticide dispersal are potentially effective against sand flies, but operational guidance is thinly based on mosquito con...

  20. Measuring the Thermal Conductivities of Low Heat Conducting Disk Samples by Monitoring the Heat Flow

    Directory of Open Access Journals (Sweden)

    José A. Ibáñez-Mengual

    2017-02-01

    Full Text Available This article aims to establish an experimental procedure to measure heat transmission coefficients in low heat conductive materials. The newly developed model takes as starting point the application of Fourier’s law to a disk sample when a temperature gradient is established between its faces. The power of a heating element is determined as the heat transfer coefficient of the problem disk. Initially, a glass vessel containing water is placed in direct contact with the heating element; then, a problem plastic disk is placed between this element and the glass vessel, treating the set as a composite wall. Prior to the above the water equivalent of a calorimetric set (vessel + water + accessories and the thermal conductivity of the vessel must be determined. The thermal conductivity of the problem plastic disk sample is obtained for temperatures ranging from 30 to 70° C. The results reveal the existence of some type of structural transition for the problem material.

  1. Results of thermal horizontal completions with sand control in Lake Maracaibo, Venezuela : case histories of horizontal gravel packs in Bachaquero-01 reservoir

    Energy Technology Data Exchange (ETDEWEB)

    Potma, J.J. [Schlumberger, IPM Prisa (Venezuela); Pizzarelli, S.G.; Gonzalez, O.E. [Petroleos de Venezuela SA, Caracas, (Venezuela); Justiniano, P.; Olivares, S.A. [Schlumberger, WCP (Venezuela)

    2002-07-01

    The experience gained through decades of applying vertical steam injection well technology in the heavy oil producing region of Lake Maracaibo in Venezuela was discussed. The oil from the Bachaquero-01 heavy oil reservoir has an API gravity of 12. Petroleum producers made an attempt to optimize production in 1996 by drilling wells with 1000 ft of horizontal section and then injecting steam. However, the initial production of 1000 BOPD dropped by 50 per cent within 4 months. A NODAL production system analysis calculation suggested that the best remedy would be to apply horizontal gravel packs to allow for more permeability compared to natural sand packs. Gravel packing of the horizontal thermal wells began in October 2000 during a drilling and completion campaign in which 18 wells were successfully gravel packed. The average production for 6 of the wells increased by 135 BOPD after 8 months compared to 9 nearby nongravel-packed horizontal wells, representing an 18 per cent higher production rate than the declining rate of the nongravel-packed wells. After one year, productivity increased by an average of 15 per cent with no sand production. Gravelpack operations were conducted at a pump rate of 2 to 3 bbl/min with a sand concentration of 0.5 to 0.7 pounds of proppant per gallon added. This maintained continuous fluid returns of 50 to 80 per cent. 18 refs., 2 tabs., 7 figs.

  2. Interplay of variable thermal conductivity and expansivity on the thermal structure of oceanic lithosphere II

    Science.gov (United States)

    Honda, S.; Yuen, D. A.

    2004-04-01

    We have extended our previous analysis of the effects of constant vs. variable, i.e., pressure and temperature dependent thermal conductivity (k) and constant thermal expansivity (a) on the thermal structure of the oceanic lithosphere. We apply our analysis to the actual data set including information on the geoid slope. The heat flow and ocean floor depth data constrain the thermal expansivity (a ≍ 3 × 10-5 1/°C). Including geoid slope data may loosely constrain both the thermal expansivity and the thermal conductivity. The probable value of thermal conductivity is ≍ 3 W/m/°C for the constant k case and ≍ 4 W/m/°C (at ambient conditions) for the variable k case. These a and k are generally consistent with laboratory data of appropriate lithospheric materials. Our analysis supports the plate model with thin lithosphere and high bottom temperature, such as GDH1 (95 km; 1450°C). Variable k case requires slightly thinner and higher temperature lithosphere (≍ 85 km and ≍ 1500°C) and gives a slightly better fit to the geoid slope data.

  3. The Lattice and Thermal Radiation Conductivity of Thermal Barrier Coatings: Models and Experiments

    Science.gov (United States)

    Zhu, Dongming; Spuckler, Charles M.

    2010-01-01

    The lattice and radiation conductivity of ZrO2-Y2O3 thermal barrier coatings was evaluated using a laser heat flux approach. A diffusion model has been established to correlate the coating apparent thermal conductivity to the lattice and radiation conductivity. The radiation conductivity component can be expressed as a function of temperature, coating material scattering, and absorption properties. High temperature scattering and absorption of the coating systems can be also derived based on the testing results using the modeling approach. A comparison has been made for the gray and nongray coating models in the plasma-sprayed thermal barrier coatings. The model prediction is found to have a good agreement with experimental observations.

  4. A transient divided-bar method for simultaneous measurements of thermal conductivity and thermal diffusivity

    Science.gov (United States)

    Bording, Thue S.; Nielsen, Søren B.; Balling, Niels

    2016-04-01

    Accurate information on thermal conductivity and thermal diffusivity of materials is of central importance in relation to geoscience and engineering problems involving the transfer of heat. Within the geosciences, this applies to all aspects regarding the determination of terrestrial heat flow and subsurface temperature modelling. Several methods, including the classical divided-bar technique, are available for laboratory measurements of thermal conductivity, and much fewer for thermal diffusivity. We have generalized the divided-bar technique to the transient case, in which thermal conductivity and volumetric heat capacity, and thereby also thermal diffusivity, are measured simultaneously. As the density of samples is easily determined independently, specific heat capacity may also be determined. Finite element formulation provides a flexible forward solution for heat transfer across the bar and thermal properties are estimated by inverse Monte Carlo modelling. This methodology enables a proper quantification of experimental uncertainties on measured thermal properties. The developed methodology was applied to laboratory measurements of various materials, including a standard ceramic material and different rock samples, and measuring results were compared with results applying traditional steady-state divided-bar and an independent line-source method. All measurements show highly consistent results and with excellent reproducibility and high accuracy. For conductivity, uncertainty is typically 1-3 %, and for diffusivity uncertainty may be reduced to about 3-5 %. The main uncertainty originates from the presence of thermal contact resistance associated with the internal interfaces of the bar. They are not resolved during inversion, and it is highly important that they are minimized by careful sample preparation.

  5. Standard test method for conducting wet sand/rubber wheel abrasion tests

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2002-01-01

    1.1 This test method covers laboratory procedures for determining the resistance of metallic materials to scratching abrasion by means of the wet sand/rubber wheel test. It is the intent of this procedure to provide data that will reproducibly rank materials in their resistance to scratching abrasion under a specified set of conditions. 1.2 Abrasion test results are reported as volume loss in cubic millimeters. Materials of higher abrasion resistance will have a lower volume loss. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  6. Thermal conductivity of organic semi-conducting materials using 3omega and photothermal radiometry techniques

    Directory of Open Access Journals (Sweden)

    Reisdorffer Frederic

    2014-01-01

    Full Text Available Organic semiconductors for opto-electronic devices show several defects which can be enhanced while increasing the operating temperature. Their thermal management and especially the reduction of their temperature are of great interest. For the heat transfer study, one has to measure the thermal conductivity of thin film organic materials. However the major difficulty for this measurement is the very low thickness of the films which needs the use of very specific techniques. In our work, the 3-omega and photothermal radiometric methods were used to measure the thermal conductivity of thin film organic semiconducting material (Alq3. The measurements were performed as function of the thin film thickness from 45 to 785 nm and also of its temperature from 80 to 350 K. With the 3 omega method, a thermal conductivity value of 0.066 W.m−1K−1 was obtained for Alq3 thin film of 200 nm at room temperature, in close agreement with the photothermal value. Both techniques appear to be complementary: the 3 omega method is easier to implement for large temperature range and small thicknesses down to a few tens of nanometers whereas the photothermal method is more suitable for thicknesses over 200nm since it provides additional information such as the thin film volumetric heat capacity.

  7. Temperature Dependent Thermal Conductivity and Thermal Interface Resistance of Pentacene Thin Films with Varying Morphology.

    Science.gov (United States)

    Epstein, Jillian; Ong, Wee-Liat; Bettinger, Christopher J; Malen, Jonathan A

    2016-07-27

    Temperature dependent thermal conductivities and thermal interface resistances of pentacene (Pn) thin films deposited on silicon substrates and self-assembled monolayer-modified [octadecyltrichlorosilane (OTS) and (3-aminopropyl)triethoxysilane (APTES)] silicon substrates were measured using frequency domain thermoreflectance. Atomic force microscopy images were used to derive an effective film thickness for thermal transport that accounts for surface roughness. Data taken over a temperature range of 77-300 K for various morphologies and film thicknesses show that the thermal conductivity increases with increasing Pn grain size. The sum of the substrate-Pn and Pn-gold thermal interface resistances was isolated from the intrinsic thermal resistance of the Pn films and found to be independent of surface chemistry. Corresponding Kapitza lengths of approximately 150 nm are larger than the physical thicknesses of typical Pn thin films and indicate that the interfaces play a dominant role in the total thermal resistance. This study has implications for increasing the performance and effective thermal management of small molecule electronic and energy conversion devices.

  8. Room temperature screening of thermal conductivity by means of thermal transient measurements

    Science.gov (United States)

    García-Cañadas, Jorge; Cheng, Shudan; Márquez-García, Lourdes; Prest, Martin J.; Akbari-Rahimabadi, Ahmad; Min, Gao

    2016-10-01

    A proof of concept of the possibility to estimate thermal conductivity of bulk disc samples at room temperature by means of thermal decays is demonstrated. An experimental set-up was designed and fabricated, which is able to perform thermal transient measurements by using a specially designed multifunctional probe that has the ability to measure temperature at its tip. Initially, the probe is heated by a heater coil located in its interior until the tip temperature reaches a steady state. Then, the probe is contacted with a disc sample which produces a temperature decay until a new state is reached. The difference between the initial and final states temperatures shows a correlation with the thermal conductivity of the sample. Employing a calibration equation, obtained using reference materials, the thermal conductivity can be calculated. Reasonably good random and systematic errors (<13% and ~9% respectively) are obtained. Theoretical simulations performed using COMSOL show a good qualitative agreement with experimental results. This new method involves an inexpensive and simple set-up which can be especially useful for thermal conductivity screening and high-throughput measurements.

  9. Advanced Liquid-Cooling Garment Using Highly Thermally Conductive Sheets

    Science.gov (United States)

    Ruemmele, Warren P.; Bue, Grant C.; Orndoff, Evelyne; Tang, Henry

    2010-01-01

    This design of the liquid-cooling garment for NASA spacesuits allows the suit to remove metabolic heat from the human body more effectively, thereby increasing comfort and performance while reducing system mass. The garment is also more flexible, with fewer restrictions on body motion, and more effectively transfers thermal energy from the crewmember s body to the external cooling unit. This improves the garment s performance in terms of the maximum environment temperature in which it can keep a crewmember comfortable. The garment uses flexible, highly thermally conductive sheet material (such as graphite), coupled with cooling water lines of improved thermal conductivity to transfer the thermal energy from the body to the liquid cooling lines more effectively. The conductive sheets can be layered differently, depending upon the heat loads, in order to provide flexibility, exceptional in-plane heat transfer, and good through-plane heat transfer. A metal foil, most likely aluminum, can be put between the graphite sheets and the external heat source/sink in order to both maximize through-plane heat transfer at the contact points, and to serve as a protection to the highly conductive sheets. Use of a wicking layer draws excess sweat away from the crewmember s skin and the use of an outer elastic fabric ensures good thermal contact of the highly conductive underlayers with the skin. This allows the current state of the art to be improved by having cooling lines that can be more widely spaced to improve suit flexibility and to reduce weight. Also, cooling liquid does not have to be as cold to achieve the same level of cooling. Specific areas on the human body can easily be targeted for greater or lesser cooling to match human physiology, a warmer external environment can be tolerated, and spatial uniformity of the cooling garment can be improved to reduce vasoconstriction limits. Elements of this innovation can be applied to other embodiments to provide effective heat

  10. Molecular Dynamics Simulation of Thermal Conductivity in Si-Ge Nanocomposites

    Institute of Scientific and Technical Information of China (English)

    HUANG Xiao-Peng; HUAI Xiu-Lan

    2008-01-01

    @@ Thermal conductivity of nanocomposites is calculated by molecular dynamics (MD) simulation. The effect of size on thermal conductivity of nanowire composites and the temperature profiles are studied. The results indicate that the thermal conductivity of nanowire composites could be much lower than alloy value; the thermal conductivity is slightly dependent on temperature except at very low temperature.

  11. Thermal and electrical conductivity of iron at Earth's core conditions.

    Science.gov (United States)

    Pozzo, Monica; Davies, Chris; Gubbins, David; Alfè, Dario

    2012-04-11

    The Earth acts as a gigantic heat engine driven by the decay of radiogenic isotopes and slow cooling, which gives rise to plate tectonics, volcanoes and mountain building. Another key product is the geomagnetic field, generated in the liquid iron core by a dynamo running on heat released by cooling and freezing (as the solid inner core grows), and on chemical convection (due to light elements expelled from the liquid on freezing). The power supplied to the geodynamo, measured by the heat flux across the core-mantle boundary (CMB), places constraints on Earth's evolution. Estimates of CMB heat flux depend on properties of iron mixtures under the extreme pressure and temperature conditions in the core, most critically on the thermal and electrical conductivities. These quantities remain poorly known because of inherent experimental and theoretical difficulties. Here we use density functional theory to compute these conductivities in liquid iron mixtures at core conditions from first principles--unlike previous estimates, which relied on extrapolations. The mixtures of iron, oxygen, sulphur and silicon are taken from earlier work and fit the seismologically determined core density and inner-core boundary density jump. We find both conductivities to be two to three times higher than estimates in current use. The changes are so large that core thermal histories and power requirements need to be reassessed. New estimates indicate that the adiabatic heat flux is 15 to 16 terawatts at the CMB, higher than present estimates of CMB heat flux based on mantle convection; the top of the core must be thermally stratified and any convection in the upper core must be driven by chemical convection against the adverse thermal buoyancy or lateral variations in CMB heat flow. Power for the geodynamo is greatly restricted, and future models of mantle evolution will need to incorporate a high CMB heat flux and explain the recent formation of the inner core.

  12. Numerical study for enhancing the thermal conductivity of phase change material (PCM) storage using high thermal conductivity porous matrix

    Energy Technology Data Exchange (ETDEWEB)

    Mesalhy, O.; Lafdi, K.; Elgafy, A.; Bowman, K. [Dayton University Research Inst., OH (United States)

    2005-04-01

    In this paper, the melting process inside an irregular geometry filled with high thermal conductivity porous matrix saturated with phase change material PCM is investigated numerically. The numerical model is resting on solving the volume averaged conservation equations for mass, momentum and energy with phase change (melting) in the porous medium. The convection motion of the liquid phase inside the porous matrix is solved considering the Darcy, Brinkman and Forchiemer effects. A local thermal non-equilibrium assumption is considered due to the large difference in thermal properties between the solid matrix and PCM by applying a two energy equation model. The numerical code shows good agreement for pure PCM melting with another published numerical work. Through this study it is found that the presence of the porous matrix has a great effect on the heat transfer and melting rate of the PCM energy storage. Decreasing the porosity of the matrix increases the melting rate, but it also damps the convection motion. It is also found that the best technique to enhance the response of the PCM storage is to use a solid matrix with high porosity and high thermal conductivity. (author)

  13. Thermal separation of soil particles from thermal conductivity measurement under various air pressures.

    Science.gov (United States)

    Lu, Sen; Ren, Tusheng; Lu, Yili; Meng, Ping; Zhang, Jinsong

    2017-01-05

    The thermal conductivity of dry soils is related closely to air pressure and the contact areas between solid particles. In this study, the thermal conductivity of two-phase soil systems was determined under reduced and increased air pressures. The thermal separation of soil particles, i.e., the characteristic dimension of the pore space (d), was then estimated based on the relationship between soil thermal conductivity and air pressure. Results showed that under both reduced and increased air pressures, d estimations were significantly larger than the geometrical mean separation of solid particles (D), which suggested that conductive heat transfer through solid particles dominated heat transfer in dry soils. The increased air pressure approach gave d values lower than that of the reduced air pressure method. With increasing air pressure, more collisions between gas molecules and solid surface occurred in micro-pores and intra-aggregate pores due to the reduction of mean free path of air molecules. Compared to the reduced air pressure approach, the increased air pressure approach expressed more micro-pore structure attributes in heat transfer. We concluded that measuring thermal conductivity under increased air pressure procedures gave better-quality d values, and improved soil micro-pore structure estimation.

  14. Thermal separation of soil particles from thermal conductivity measurement under various air pressures

    Science.gov (United States)

    Lu, Sen; Ren, Tusheng; Lu, Yili; Meng, Ping; Zhang, Jinsong

    2017-01-01

    The thermal conductivity of dry soils is related closely to air pressure and the contact areas between solid particles. In this study, the thermal conductivity of two-phase soil systems was determined under reduced and increased air pressures. The thermal separation of soil particles, i.e., the characteristic dimension of the pore space (d), was then estimated based on the relationship between soil thermal conductivity and air pressure. Results showed that under both reduced and increased air pressures, d estimations were significantly larger than the geometrical mean separation of solid particles (D), which suggested that conductive heat transfer through solid particles dominated heat transfer in dry soils. The increased air pressure approach gave d values lower than that of the reduced air pressure method. With increasing air pressure, more collisions between gas molecules and solid surface occurred in micro-pores and intra-aggregate pores due to the reduction of mean free path of air molecules. Compared to the reduced air pressure approach, the increased air pressure approach expressed more micro-pore structure attributes in heat transfer. We concluded that measuring thermal conductivity under increased air pressure procedures gave better-quality d values, and improved soil micro-pore structure estimation.

  15. Controlling thermal chaos in the mantle by positive feedback from radiative thermal conductivity

    Directory of Open Access Journals (Sweden)

    F. Dubuffet

    2002-01-01

    Full Text Available The thermal conductivity of mantle materials has two components, the lattice component klat from phonons and the radiative component krad due to photons. These two contributions of variable thermal conductivity have a nonlinear dependence in the temperature, thus endowing the temperature equation in mantle convection with a strongly nonlinear character. The temperature derivatives of these two mechanisms have different signs, with ∂klat /∂T negative and dkrad /dT positive. This offers the possibility for the radiative conductivity to control the chaotic boundary layer instabilities developed in the deep mantle. We have parameterized the weight factor between krad and klat with a dimensionless parameter f , where f = 1 corresponds to the reference conductivity model. We have carried out two-dimensional, time-dependent calculations for variable thermal conductivity but constant viscosity in an aspect-ratio 6 box for surface Rayleigh numbers between 106 and 5 × 106. The averaged Péclet numbers of these flows lie between 200 and 2000. Along the boundary in f separating the chaotic and steady-state solutions, the number decreases and the Nusselt number increases with internal heating, illustrating the feedback between internal heating and radiative thermal conductivity. For purely basal heating situation, the time-dependent chaotic flows become stabilized for values of f of between 1.5 and 2. The bottom thermal boundary layer thickens and the surface heat flow increases with larger amounts of radiative conductivity. For magnitudes of internal heating characteristic of a chondritic mantle, much larger values of f , exceeding 10, are required to quench the bottom boundary layer instabilities. By isolating the individual conductive mechanisms, we have ascertained that the lattice conductivity is partly responsible for inducing boundary layer instabilities, while the radiative conductivity and purely depth-dependent conductivity exert a stabilizing

  16. Electrically and Thermally Conducting Nanocomposites for Electronic Applications

    Directory of Open Access Journals (Sweden)

    Daryl Santos

    2010-02-01

    Full Text Available Nanocomposites made up of polymer matrices and carbon nanotubes are a class of advanced materials with great application potential in electronics packaging. Nanocomposites with carbon nanotubes as fillers have been designed with the aim of exploiting the high thermal, electrical and mechanical properties characteristic of carbon nanotubes. Heat dissipation in electronic devices requires interface materials with high thermal conductivity. Here, current developments and challenges in the application of nanotubes as fillers in polymer matrices are explored. The blending together of nanotubes and polymers result in what are known as nanocomposites. Among the most pressing current issues related to nanocomposite fabrication are (i dispersion of carbon nanotubes in the polymer host, (ii carbon nanotube-polymer interaction and the nature of the interface, and (iii alignment of carbon nanotubes in a polymer matrix. These issues are believed to be directly related to the electrical and thermal performance of nanocomposites. The recent progress in the fabrication of nanocomposites with carbon nanotubes as fillers and their potential application in electronics packaging as thermal interface materials is also reported.

  17. Nanoscale Electromechanics To Measure Thermal Conductivity, Expansion, and Interfacial Losses.

    Science.gov (United States)

    Mathew, John P; Patel, Raj; Borah, Abhinandan; Maliakkal, Carina B; Abhilash, T S; Deshmukh, Mandar M

    2015-11-11

    We study the effect of localized Joule heating on the mechanical properties of doubly clamped nanowires under tensile stress. Local heating results in systematic variation of the resonant frequency; these frequency changes result from thermal stresses that depend on temperature dependent thermal conductivity and expansion coefficient. The change in sign of the linear expansion coefficient of InAs is reflected in the resonant response of the system near a bath temperature of 20 K. Using finite element simulations to model the experimentally observed frequency shifts, we show that the thermal conductivity of a nanowire can be approximated in the 10-60 K temperature range by the empirical form κ = bT W/mK, where the value of b for a nanowire was found to be b = 0.035 W/mK(2), significantly lower than bulk values. Also, local heating allows us to independently vary the temperature of the nanowire relative to the clamping points pinned to the bath temperature. We suggest a loss mechanism (dissipation ~10(-4)-10(-5)) originating from the interfacial clamping losses between the metal and the semiconductor nanostructure.

  18. Enhancement of thermal contact conductance for electronic systems

    Energy Technology Data Exchange (ETDEWEB)

    Sartre, V.; Lallemand, M. [Centre de Thermique de Lyon, UMR CNRS 5008, INSA, Villeurbanne (France)

    2001-02-01

    Experimental investigations on thermal contact resistance have been performed. The results of this study will be useful in selecting interstitial materials to enhance the thermal conductance of an electronic component/heat sink assembly. The experimental assembly consists of two specimens: a thick copper plate, electrically heated, and an aluminium water-cooled plate. The two specimens are bolted together and the load is applied using a calibrated torque wrench. Various interstitial materials (seven commercial greases and 12 foils) suitable for the thermal enhancement in electronic systems have been investigated. The variables considered are the bolt torque, the heat transfer rate and the grease or foil thickness. Results show that the most influential parameter is the applied torque. The contact resistance decreases as the heat flux or the film thickness decreases. The highest dimensionless contact conductance factors (E) are achieved with greases (3 < E < 6). Phase change material-coated foils exhibit E-values ranging from 2.5 to 3.5. Graphite or metallic foils have E-values lower than 2 and for silicone foils E is significantly reduced (E < 1). Thus, phase change material-coated foils seem to be very promising materials, since they are efficient, easy to implement and do not migrate and vaporise out of the contact area. (author)

  19. Decomposition model for phonon thermal conductivity of a monatomic lattice

    Science.gov (United States)

    Evteev, Alexander V.; Momenzadeh, Leila; Levchenko, Elena V.; Belova, Irina V.; Murch, Graeme E.

    2014-12-01

    An analytical treatment of decomposition of the phonon thermal conductivity of a crystal with a monatomic unit cell is developed on the basis of a two-stage decay of the heat current autocorrelation function observed in molecular dynamics simulations. It is demonstrated that the contributions from the acoustic short- and long-range phonon modes to the total phonon thermal conductivity can be presented in the form of simple kinetic formulas, consisting of products of the heat capacity and the average relaxation time of the considered phonon modes as well as the square of the average phonon velocity. On the basis of molecular dynamics calculations of the heat current autocorrelation function, this treatment allows for a self-consistent numerical evaluation of the aforementioned variables. In addition, the presented analysis allows, within the Debye approximation, for the identification of the temperature range where classical molecular dynamics simulations can be employed for the prediction of phonon thermal transport properties. As a case example, Cu is considered.

  20. Suppression of Electron Thermal Conduction in the Intracluster Medium

    Science.gov (United States)

    Roberg-Clark, Gareth; Drake, James; Swisdak, M.; Reynolds, Christopher S.

    2017-08-01

    The Intracluster Medium (ICM) contains high-temperature dilute plasma in which the quantity beta, defined as the ratio of the thermal pressure of the gas to the local magnetic field pressure, is much larger than unity. In addition, the collisional mean free path of particles in the ICM is typically large compared to the magnetic gyro-radius of individual particles. These conditions allow for the growth of robust microinstabilities that can significantly alter the transport of particles and heat along the local magnetic field line. Here we explore such an instability using driven two-dimensional Particle-In-Cell simulations of a magnetized plasma with a temperature gradient imposed at the boundaries. The system is highly unstable and develops large-amplitude magnetic fluctuations that effectively scatter the orbits of electrons crossing the simulation domain, resulting in a collisionless suppression of thermal conduction across the temperature gradient and magnetic field. The results suggest that the spontaneous development of small-scale plasma turbulence in the ICM may play a pivotal role in determining the thermal conductivity of ICM-like plasmas.

  1. Thermal Conductance Engineering for High-Speed TES Microcalorimeters

    Science.gov (United States)

    Hays-Wehle, J. P.; Schmidt, D. R.; Ullom, J. N.; Swetz, D. S.

    2016-07-01

    Many current and future applications for superconducting transition-edge sensor (TES) microcalorimeters require significantly faster pulse response than is currently available. X-ray spectroscopy experiments at next-generation synchrotron light sources need to successfully capture very large fluxes of photons, while detectors at free-electron laser facilities need pulse response fast enough to match repetition rates of the source. Additionally, neutrino endpoint experiments such as HOLMES need enormous statistics, yet are extremely sensitive to pile-up effects that can distort spectra. These issues can be mitigated only by fast rising and falling edges. To address these needs, we have designed high-speed TES detectors with novel geometric enhancements to increase the thermal conductance of pixels suspended on silicon nitride membranes. This paper shows that the thermal conductivity can be precisely engineered to values spanning over an order of magnitude to achieve fast thermal relaxation times tailored to the relevant applications. Using these pixel prototypes, we demonstrate decay time constants faster than 100 μ s, while still maintaining spectral resolution of 3 eV FWHM at 1.5 keV. This paper also discusses the trade-offs inherent in reducing the pixel time constant, such as increased bias current leading to degradation in energy resolution, and potential modifications to improve performance.

  2. Demystifying umklapp vs normal scattering in lattice thermal conductivity

    Science.gov (United States)

    Maznev, A. A.; Wright, O. B.

    2014-11-01

    We discuss the textbook presentation of the concept of umklapp vs normal phonon-phonon scattering processes in the context of lattice thermal conductivity. A simplistic picture, in which the "momentum conservation" in a normal process leads to the conservation of the heat flux, is only valid within the single-velocity Debye model of phonon dispersion. Outside this model, the simple "momentum conservation" argument is demonstrably inaccurate and leads to conceptual confusion. Whether or not an individual scattering event changes the direction of the energy flow is determined by the phonon group velocity, which, unlike the quasimomentum, is a uniquely defined quantity independent of the choice of the primitive cell in reciprocal space. Furthermore, the statement that normal processes do not lead to a finite thermal conductivity when umklapp processes are absent is a statistical statement that applies to a phonon distribution rather than to individual scattering events. It is also important to understand that once umklapp processes are present, both normal and umklapp processes contribute to thermal resistance. A nuanced explanation of the subject would help avoid confusion of the student and establish a connection with cutting edge research.

  3. Thermal conductivity of halite using a pulsed laser

    Energy Technology Data Exchange (ETDEWEB)

    Smith, D.D.

    1976-12-13

    A feasibility study of the experimental determination of thermal conductivities of salts (NaCl) and a steel casing material using a pulsed laser technique are presented. Optically transparent materials such as salt were effectively coated with an opaque layer of aluminum or silver to satisfy test boundary conditions. Thermal conductivities for the three specimens were obtained from the thermal diffusivity, heat capacity and density relationship. Based on measurements from room temperature to 923/sup 0/K, single crystal halite yielded values ranging from 6.5 to 1.5 W/m-K versus 5.5 to 1.2 W/m-K for Avery Island Bed Salt. AISI 106-Grade B steel gave values of 46 to 29 W/m-K. While these measurements may be no better than +- 10 percent, it is possible with appropriate equipment and technique to generate data of engineering quality, +- 5 percent error, provided adequate test specimens can be fabricated. Attributes of this technique include the generation of data very quickly which is more applicable to testing large numbers of specimens relative to steady-state methods. The use of penny-sized specimens can be a problem from the fabrication requirement, especially for friable and anisotropic geological materials. The quality of the data rests on the adherence of the experimental design to the mathematical model.

  4. Lower-Conductivity Ceramic Materials for Thermal-Barrier Coatings

    Science.gov (United States)

    Bansal, Narottam P.; Zhu, Dongming

    2006-01-01

    Doped pyrochlore oxides of a type described below are under consideration as alternative materials for high-temperature thermal-barrier coatings (TBCs). In comparison with partially-yttria-stabilized zirconia (YSZ), which is the state-of-the-art TBC material now in commercial use, these doped pyrochlore oxides exhibit lower thermal conductivities, which could be exploited to obtain the following advantages: For a given difference in temperature between an outer coating surface and the coating/substrate interface, the coating could be thinner. Reductions in coating thicknesses could translate to reductions in weight of hot-section components of turbine engines (e.g., combustor liners, blades, and vanes) to which TBCs are typically applied. For a given coating thickness, the difference in temperature between the outer coating surface and the coating/substrate interface could be greater. For turbine engines, this could translate to higher operating temperatures, with consequent increases in efficiency and reductions in polluting emissions. TBCs are needed because the temperatures in some turbine-engine hot sections exceed the maximum temperatures that the substrate materials (superalloys, Si-based ceramics, and others) can withstand. YSZ TBCs are applied to engine components as thin layers by plasma spraying or electron-beam physical vapor deposition. During operation at higher temperatures, YSZ layers undergo sintering, which increases their thermal conductivities and thereby renders them less effective as TBCs. Moreover, the sintered YSZ TBCs are less tolerant of stress and strain and, hence, are less durable.

  5. Negative differential thermal conductance and thermal rectification effects across a graphene-based superconducting junction

    Science.gov (United States)

    Zhou, Xingfei; Zhang, Zhi

    2016-05-01

    We study the heat transport in a graphene-based normal-superconducting junction by solving the Bogoliubov-de Gennes (BdG) equation. There are two effects, the competitive and cooperative effects, which come from the interaction between the temperature-dependent energy-gap function in the superconducting region and the occupation difference of quasiparticles. It is found that the competitive effect can not only bring the negative differential thermal conductance effect but also the thermal rectification effect. By contrast, the cooperative effect just causes the thermal rectification effect. Furthermore, the thermal rectification ratio and the magnitude of heat current should be seen as two inseparable signs for characterizing the thermal rectification effect. These discoveries can add more application for the graphene-based superconducting junction, such as heat diode and heat transistor, at cryogenic temperatures.

  6. Accurately simulating anisotropic thermal conduction on a moving mesh

    CERN Document Server

    Kannan, Rahul; Pakmor, Rüdiger; Marinacci, Federico; Vogelsberger, Mark

    2015-01-01

    We present a novel implementation of an extremum preserving anisotropic diffusion solver for thermal conduction on the unstructured moving Voronoi mesh of the AREPO code. The method relies on splitting the one-sided facet fluxes into normal and oblique components, with the oblique fluxes being limited such that the total flux is both locally conservative and extremum preserving. The approach makes use of harmonic averaging points and a simple, robust interpolation scheme that works well for strong heterogeneous and anisotropic diffusion problems. Moreover, the required discretisation stencil is small. Efficient fully implicit and semi-implicit time integration schemes are also implemented. We perform several numerical tests that evaluate the stability and accuracy of the scheme, including applications such as point explosions with heat conduction and calculations of convective instabilities in conducting plasmas. The new implementation is suitable for studying important astrophysical phenomena, such as the co...

  7. Hot wire needle probe for thermal conductivity detection

    Energy Technology Data Exchange (ETDEWEB)

    Condie, Keith Glenn; Rempe, Joy Lynn; Knudson, Darrell lee; Daw, Joshua Earl; Wilkins, Steven Curtis; Fox, Brandon S.; Heng, Ban

    2015-11-10

    An apparatus comprising a needle probe comprising a sheath, a heating element, a temperature sensor, and electrical insulation that allows thermal conductivity to be measured in extreme environments, such as in high-temperature irradiation testing. The heating element is contained within the sheath and is electrically conductive. In an embodiment, the heating element is a wire capable of being joule heated when an electrical current is applied. The temperature sensor is contained within the sheath, electrically insulated from the heating element and the sheath. The electrical insulation electrically insulates the sheath, heating element and temperature sensor. The electrical insulation fills the sheath having electrical resistance capable of preventing electrical conduction between the sheath, heating element, and temperature sensor. The control system is connected to the heating element and the temperature sensor.

  8. Thermal signature and thermal conductivities of PEM fuel cells; PEM = Proton Exchange Membrane

    Energy Technology Data Exchange (ETDEWEB)

    Burheim, Odne Stokke

    2009-11-15

    The work gives estimates on thermal gradients within the PEM fuel cell, an experimental route to measure the through-plane thermal conductivity of the materials used in the PEM fuel cell and also suggestions of which material characteristics should be aimed for with respect to thermal management of fuel cells. The work reports for the first time how the thermal conductivity of Nafion changes with water content. An effect residual water has on the thermal conductivity of the PTL is also reported for the first time. In addition to this a calorimeter for the PEMFC was constructed to measure the thermal signature. This is also reported for the first time in the literature. To elucidate the heat gradients possible within a PEM fuel cell and to better understand the calorimetric measurements, a 2D thermal model was created and applied at different conditions. The model was made by the use of the finite element method software COMSOL 3.3. This model was used to evaluate temperature elevations in the single cell mainly imposed by water transport, component thermal conductivity modifications and gas flow channel design. The 2D model was compared to a 1 D model to demonstrate the importance of taking the gas flow channel design into account. Parallel gas flow channels tend to impose an increased current density under the gas channel while serpentine flow channel pattern does the opposite, according to several studies. Thus a simple 2D model can, as very good approximation, be used to study effects rising from 3D cell designs. It was demonstrated that parallel flow fields give a higher maximum temperature than serpentine gas flow channels. Changes in the porous transport layer, such as compression, residual water and increased through-plane thermal conductivity were also discussed. In general, the maximum temperatures predicted for the PEM fuel cell were between 4.5 and 15 K above the control temperature in the polarization plate, depending on the conditions in the model. One

  9. Thermal insulating materials. Thermal conductivity variations in mineral wool and expanded polystyrene; Vaermeisoleringsmaterial. Databas foer vaermekonduktivitetsmaetningar

    Energy Technology Data Exchange (ETDEWEB)

    Jonsson, B.

    1995-05-01

    Thermal conductivity has been measured by SP since 1965. This has provided a substantial data base of results, from which measurements for different groups of materials have ben compared in order to give an idea of normal variations and mean values. Values for polystyrene, glass fiber, and mineral wool have been statistically investigated. In general, it is the density dependence of the thermal conductivity that has been investigated, although air permeability as an indirect parameter has also been studied. The expression A + B*d + C/d has been employed to describe the thermal conductivity in a porous material, and has been found preferable to other types of polynomials. Systematic differences from the mean curve can be detected by employing the difference between the measured values and the theoretical values (the residual), which provides a means of detecting sub-standard (or super-standard) batches. 12 refs, 13 figs

  10. Thermal Moore's law and near-field thermal conductance in carbon-based electronics

    Science.gov (United States)

    Rotkin, Slava V.

    2009-08-01

    The novel thermal conductance mechanism, theoretically predicted and experimentally measured in nanotube field-effect transistors (FET), is discussed with respect to the power dissipation problem of modern carbon-based electronics. Such an effect is due to the near-field coupling of the charge carriers in the transistor channel with the local electric field of the surface electromagnetic modes. The coupling leads to a quantum electrodynamic (QED) energy exchange between the hot electrons in FET channel and the optical polar phonon bath being in thermal equilibrium with the substrate. For an example of a NT on silica, this QED coupling mechanism is shown to exceed significantly the interface Kapitza conductance, that is, the classical phonon heat transport. The QED thermal conductance is proposed to play dominant role in the energy dissipation in nanoelectronics with a hetero-interface between the device channel and the polar substrate.

  11. Strong anisotropic thermal conductivity of monolayer WTe2

    Science.gov (United States)

    Ma, Jinlong; Chen, Yani; Han, Zheng; Li, Wu

    2016-12-01

    Tungsten ditelluride (WTe2) has attracted increasing attention due to its large magnetoresistance and pressure-induced superconductivity. In this work, we investigate the thermal conductivity (κ) of monolayer WTe2 by performing first-principles calculations, and find strong anisotropic κ with predicted room-temperature values of 9 and 20 W m-1 K-1 along two principal lattice directions, respectively. Such strong anisotropy suggests the importance of orientation when engineering thermal-related applications based on WTe2. The anisotropy of κ is attributed to the in-plane linear acoustic phonon branches, while the out-of-plane quadratic acoustic phonon branch is almost isotropic. The size dependence of κ shows that the size effect can persists up to 10 μm, and the anisotropy decreases with decreasing sample size due to the suppression of low-frequency anisotropic phonons by boundary scattering.

  12. Thermal conductivity of silica nanoparticle powder: Measurement and theoretical analysis

    Science.gov (United States)

    Huang, Congliang; Lin, Zizhen; Feng, Yanhui; Zhang, Xinxin; Wang, Ge

    2015-12-01

    The hot-wire method was applied to experimentally determine the thermal conductivity (TC) of a silica nanoparticle powder. A fitting model was further employed to analyze the experimental results and to predict the TC over a wider porosity scale. Results show that the effective TC of the silica-nanoparticle powder can be less than that of free air because of the low TC of both the silica nanoparticles and the air confined in the pore spaces; the relative contribution of the nanoparticle TC, the confined air TC, and the radiation heat transfer coefficient to the effective TC will significantly affect at which porosity the extreme value of the effective TC occurs; the porosity obtained when the contribution to the effective TC of the confined air equals that of the nanoparticles is the most favorable for constructing thermal insulation materials.

  13. Assessment of some soil thermal conductivity models via variations in temperature and bulk density at low moisture range

    Science.gov (United States)

    Mahdavi, Seyed Mohamad; Neyshabouri, Mohammad Reza; Fujimaki, Haruyuki

    2016-08-01

    Simulation of heat transfer in soil under steady and unsteady situations requires reliable estimate of soil thermal conductivity (λ) at varying environmental conditions. In the current work several soil thermal conductivity predicting models including I) de Vries, II) Campbell, III) combined de Vries and Campbell and IV) de Vries-Nobre were evaluated for the four soils of coarse sand, sandy loam, loam and clay loam textured at varying in temperature and bulk density at low moisture range. Thermal conductivities measured by the cylindrical probe method served as the reference for models assessment. Results showed that approximately same thermal conductivities obtained by the five methods at low moisture range (θ ≤ 0.05 m3/m3). Also the de Vries and de Vries-Campbell models produced accurate than Campbell and de vries-Nobre models. The accuracy of the two models increased with soil compaction but decreased with temperature rise. Campbell model showed more reliability at higher (311.16 and 321.16 K) temperatures; but its accuracy declined with soil compaction in current work. It seems that assuming needle shape for the soil particles is far away from the reality whereas assuming spherical shapes may be more realistic and produced more satisfactory prediction of thermal conductivity. The compaction would alter particle arrangement and may increase the contact area of particles; and then make them behave more or less spherical shape.it seems thermal conductivity in solid particles increase via increasing in temperature. Since a modified mineral shape factor, g m , was developed as a combination between sphere and needle according to geometric mean particle diameter as well as bulk density and temperature as modifying factors. This factor increased the accuracy of de Vries-Nobre model up to 10.37%. Regarding nonlinear regression model, moisture content, bulk density, temperature and quartz content demonstrated significant effect on soil thermal conductivity in our

  14. Swift heavy ion irradiation reduces porous silicon thermal conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Massoud, M.; Canut, B. [Université de Lyon, Institut des Nanotechnologies de Lyon INL-UMR5270, CNRS, INSA de Lyon, F-69621 Villeurbanne (France); Newby, P.; Frechette, L. [Centre de Recherche en Nanofabrication et Nanocaractérisation (CNR2), Université de Sherbrooke, Sherbrooke, Québec (Canada); Chapuis, P.O. [Université de Lyon, Centre de Thermique de Lyon CETHIL-UMR5008, CNRS, INSA de Lyon, F-69621 Villeurbanne (France); Bluet, J.M. [Université de Lyon, Institut des Nanotechnologies de Lyon INL-UMR5270, CNRS, INSA de Lyon, F-69621 Villeurbanne (France)

    2014-12-15

    While the electrical conductivity of semiconductors can be easily changed over order of magnitudes (8 in silicon) by playing on the doping, the thermal conductivity (TC) control is a challenging issue. Nevertheless, numerous applications require TC control in Si down to 1 W m{sup −1} K{sup −1}. Among them, there are thermal insulation requirements in MEMS, thermal management issues in 3D packaging or TC reduction for thermoelectric applications. Towards this end, the formation of nanoporous Si by electrochemical anodisation is efficient. Nevertheless, in this case the material is too fragile for MEMS application or even to withstand CMOS technological processes. In this work, we show that ion irradiation in the electronic regime is efficient for reducing TC in meso-porous Si (PSi), which is more mechanically robust than the nanoporous PSi. We have studied three different mass to energy ratios ({sup 238}U at 110 MeV and {sup 130}Xe at 91 MeV and 29 MeV) with fluences ranging from 10{sup 12} cm{sup −2} to 7 × 10{sup 13} cm{sup −2}. The sample properties, after irradiation, have been measured by infrared spectroscopy, Raman spectroscopy and scanning electron microscopy. The TC has been measured using scanning thermal microscopy. Although, bulk Si is insensitive to ion interaction in the electronic regime, we have observed the amorphisation of the PSi resulting in a TC reduction even for the low dose and energy. For the highest irradiation dose a very important reduction factor of four was obtained.

  15. Effect of interfacial treatment on the thermal properties of thermal conductive plastics

    Directory of Open Access Journals (Sweden)

    2007-09-01

    Full Text Available In this paper, ZnO, which is processed by different surface treatment approaches, is blended together with polypropylene to produce thermal conductive polymer composites. The composites are analyzed by Fourier transform infrared (FTIR spectroscopy and scanning electron microscopy (SEM to investigate the surface modification of filler, their distribution in the matrix and the condition of two-phase interface. Optimized content of filler surface modifier is investigated as well. The results showed that using low-molecular coupling agent produces positive effect to improve the interface adhesion between filler and matrix, and the thermal conductivity of the composite as well. Macro-molecular coupling agent can strongly improve two-phase interface, but it is not beneficial at obtaining a high thermal conductivity. The blend of ZnO without modification and polypropylene has many defects in the two-phase interface, and the thermal conductivity of the composite is between those of composites produced by previous two approaches. The surface treatment of the filler also allowed producing the composites with lower coefficient of thermal expansion (CTE. As for the content of low-molecular coupling agent, it obtains the best effect at 1.5 wt%.

  16. Extremely high thermal conductivity anisotropy of double-walled carbon nanotubes

    Directory of Open Access Journals (Sweden)

    Zhaoji Ma

    2017-06-01

    Full Text Available Based on molecular dynamics simulations, we reveal that double-walled carbon nanotubes can possess an extremely high anisotropy ratio of radial to axial thermal conductivities. The mechanism is basically the same as that for the high thermal conductivity anisotropy of graphene layers - the in-plane strong sp2 bonds lead to a very high intralayer thermal conductivity while the weak van der Waals interactions to a very low interlayer thermal conductivity. However, different from flat graphene layers, the tubular structures of carbon nanotubes result in a diameter dependent thermal conductivity. The smaller the diameter, the larger the axial thermal conductivity but the smaller the radial thermal conductivity. As a result, a DWCNT with a small diameter may have an anisotropy ratio of thermal conductivity significantly higher than that for graphene layers. The extremely high thermal conductivity anisotropy allows DWCNTs to be a promising candidate for thermal management materials.

  17. Extremely high thermal conductivity anisotropy of double-walled carbon nanotubes

    Science.gov (United States)

    Ma, Zhaoji; Guo, Zhengrong; Zhang, Hongwei; Chang, Tienchong

    2017-06-01

    Based on molecular dynamics simulations, we reveal that double-walled carbon nanotubes can possess an extremely high anisotropy ratio of radial to axial thermal conductivities. The mechanism is basically the same as that for the high thermal conductivity anisotropy of graphene layers - the in-plane strong sp2 bonds lead to a very high intralayer thermal conductivity while the weak van der Waals interactions to a very low interlayer thermal conductivity. However, different from flat graphene layers, the tubular structures of carbon nanotubes result in a diameter dependent thermal conductivity. The smaller the diameter, the larger the axial thermal conductivity but the smaller the radial thermal conductivity. As a result, a DWCNT with a small diameter may have an anisotropy ratio of thermal conductivity significantly higher than that for graphene layers. The extremely high thermal conductivity anisotropy allows DWCNTs to be a promising candidate for thermal management materials.

  18. Effects of basal-plane thermal conductivity and interface thermal conductance on the hot spot temperature in graphene electronic devices

    Science.gov (United States)

    Choi, David; Poudel, Nirakar; Cronin, Stephen B.; Shi, Li

    2017-02-01

    Electrostatic force microscopy and scanning thermal microscopy are employed to investigate the electric transport and localized heating around defects introduced during transfer of graphene grown by chemical vapor deposition to an oxidized Si substrate. Numerical and analytical models are developed to explain the results based on the reported basal-plane thermal conductivity, κ, and interfacial thermal conductance, G, of graphene and to investigate their effects on the peak temperature. Irrespective of the κ values, increasing G beyond 4 × 107 W m-2 K-1 can reduce the peak temperature effectively for graphene devices made on sub-10 nm thick gate dielectric, but not for the measured device made on 300-nm-thick oxide dielectric, which yields a cross-plane thermal conductance (Gox) much smaller than the typical G of graphene. In contrast, for typical G values reported for graphene, increasing κ from 300 W m-1 K-1 toward 3000 W m-1 K-1 is effective in reducing the hot spot temperature for the 300-nm-thick oxide devices but not for the sub-10 nm gate dielectric case, because the heat spreading length (l) can be appreciably increased relative to the micron-scale localized heat generation spot size (r0) only when the oxide layer is sufficiently thick. As such, enhancement of κ increases the vertical heat transfer area above the gate dielectric only for the thick oxide case. In all cases considered, the hot spot temperature is sensitive to varying G and κ only when the G/Gox ratio and r0/l ratio are below about 5, respectively.

  19. Temporal changes in hydraulic conductivity of sand porous media biofilters during wastewater infiltration due to biomat formation

    Science.gov (United States)

    Beach, Deborah N. H.; McCray, John E.; Lowe, Kathryn S.; Siegrist, Robert L.

    2005-09-01

    Porous media biofilters (PMBs) are commonly used to treat domestic wastewater. Biomats develop at the infiltrative surface of PMBs due to continued wastewater application and create an impedance to flow. The goal of this research is to quantify the temporal evolution of normalized biomat hydraulic conductivity ( Kbm/ bbm) and effective hydraulic conductivity ( Ke). Ke is the overall hydraulic conductivity of the infiltrative zone, including biomat and unsaturated media below the biomat. Research was conducted using eight one-dimensional (1D) sand columns with gravel-free and gravel-laden infiltrative surfaces. The columns were loaded at design rates of 100-200 cm/d for 20 weeks of column operation. The Ke values for these continuously loaded columns were determined from analyses of bromide-tracer tests, falling-head permeability tests, and volumetric water content measurements during biomat development. The reduction in the Ke due to biomat formation is due to two factors: reduced hydraulic conductivity of the thin biomat, and a reduced hydraulic conductivity of the subsoil due to development of a biomat-induced unsaturated flow regime. Unsaturated hydraulic conductivities of the subsoil below the biomat ( Kss) were estimated from capillary curves and water content measurements. For observed final biomat thicknesses (less than 1 cm), the biomat hydraulic conductivity, Kbm, is three orders of magnitude smaller than the unsaturated hydraulic conductivity ( Kss). However, the relatively large thickness of the vadose zone causes the Kss to be an important contributor to the overall Ke value. For these columns, the final Ke values were approximately two orders of magnitude smaller than the original value. Because the exact thickness of the biomat ( bbm) is unknown during the flow experiments, the hydraulic conductance of the biomat zone is presented using a normalized hydraulic conductivity function ( Kbm/ bbm). A similar Kbm/ bbm is reached regardless of wastewater

  20. Suppression of thermal conduction in a mirror-unstable plasma

    CERN Document Server

    Komarov, S V; Kunz, M W; Schekochihin, A A

    2016-01-01

    The ICM plasma is subject to firehose and mirror instabilities at scales of order the ion Larmor radius. The mirror instability generates fluctuations of magnetic-field strength $\\delta B / B \\sim 1$. These fluctuations act as magnetic traps for the heat-conducting electrons, suppressing their transport. We calculate the effective parallel thermal conductivity in the ICM in the presence of the mirror fluctuations for different stages of the evolution of the instability. The mirror fluctuations are limited in amplitude by the maximum and minimum values of the field strength, with no large deviations from the mean value. This key property leads to a finite suppression of thermal conduction at large scales. We find suppression down to $\\approx 0.2$ of the Spitzer value for the secular phase of the perturbations' growth, and $\\approx 0.3$ for their saturated phase. The effect operates in addition to other suppression mechanisms and independently of them. Globally, fluctuations $\\delta B / B \\sim 1$ can be present...

  1. Electrical Conductivity, Thermal Behavior, and Seebeck Coefficient of Conductive Films for Printed Thermoelectric Energy Harvesting Systems

    Science.gov (United States)

    Ankireddy, Krishnamraju; Menon, Akanksha K.; Iezzi, Brian; Yee, Shannon K.; Losego, Mark D.; Jur, Jesse S.

    2016-11-01

    Printed electronics is being explored as a rapid, facile means for manufacturing thermoelectric generators (TEGs) that can recover useful electrical energy from waste heat. This work examines the relevant electrical conductivity, thermal resistance, thermovoltage, and Seebeck coefficient of printed films for use in such printed flexible TEGs. The thermoelectric performance of TEGs printed using commercially relevant nickel, silver, and carbon inks is evaluated. The microstructure of the printed films is investigated to better understand why the electrical conductivity and Seebeck coefficient are degraded. Thermal conduction is shown to be relatively insensitive to the type of metalized coating and nearly equivalent to that of an uncoated polymer substrate. Of the commercially available conductive ink materials examined, carbon-nickel TEGs are shown to exhibit the highest thermovoltage, with a value of 10.3 μV/K. However, silver-nickel TEGs produced the highest power generation of 14.6 μW [from 31 junctions with temperature difference (Δ T) of 113°C] due to their low electrical resistance. The voltage generated from the silver-nickel TEG was stable under continuous operation at 275°C for 3 h. We have also demonstrated that, after a year of storage in ambient conditions, these devices retain their performance. Notably, the electrical conductivity and Seebeck coefficient measured for individual materials were consistent with those measured from actual printed TEG device structures, validating the need for further fundamental materials characterization to accelerate flexible TEG device optimization.

  2. Thermal conductivity of refrigerant mixtures; Waermeleitfaehigkeit von HFKW-Gemischen

    Energy Technology Data Exchange (ETDEWEB)

    Spindler, K. [Stuttgart Univ. (Germany). Inst. fuer Thermodynamik und Waermetechnik; Hoffmann, N. [Stuttgart Univ. (Germany). Inst. fuer Thermodynamik und Waermetechnik; Hahne, E. [Stuttgart Univ. (Germany). Inst. fuer Thermodynamik und Waermetechnik

    1997-01-01

    Thermal conductivity measurements of saturated liquid and saturated vapour are presented for three binary mixtures of the refrigerants R 32 and R 125, R 410A included, for the binary mixture R 507 and for the ternary mixture R 407C. The experimental results for the mixtures are compared with the sum of the molar weighted values of the pure components and with values calculated from existing correlations in literature. The thermal conductivity of the mixture in the saturated vapour phase can be calculated by molar weighting the values of the pure components. The thermal conductivity of the mixture in the saturated liquid state is lower than the sum of the molar weighted value of the pure components. For the saturated liquid the values calculated with the correlation of Wassiljewa agree best with the experimental results. (orig.) [Deutsch] Im Verdampfungsbereich von -60 C bis -20 C wurden bisher die Kaeltemittel R 22 und R 502 verwendet. Waehrend R 22 in Neuanlagen noch bis 31. Dezember 1999 eingesetzt werden darf, ist dies nach den Bestimmungen der FCKW-Halon-Verbotsverordnung fuer R 502 schon seit 1992 fuer grosse Anlagen (>5 kg Fuellmenge) und seit 1995 auch fuer kleine oder mobile Anlagen verboten. HFKW`s und deren Gemische sind als Ersatzkaeltemittel bereits im Einsatz. Die fuer eine optimale Auslegung einer Anlage benoetigten Stoffwerte sind jedoch nur zum Teil oder lueckenhaft vorhanden. Zur Auslegung von Waermeuebertragern muss die spezifische Waermekapazitaet, die Waermeleitfaehigkeit und die Viskositaet des Fluides bekannt sein. Waehrend die Waermeleitfaehigkeit der Reinstoffe zum groessten Teil ausreichend bekannt ist, gab es zu den Gemischen bisher keine Messwerte. (orig.)

  3. Unusually High and Anisotropic Thermal Conductivity in Amorphous Silicon Nanostructures.

    Science.gov (United States)

    Kwon, Soonshin; Zheng, Jianlin; Wingert, Matthew C; Cui, Shuang; Chen, Renkun

    2017-03-28

    Amorphous Si (a-Si) nanostructures are ubiquitous in numerous electronic and optoelectronic devices. Amorphous materials are considered to possess the lower limit to the thermal conductivity (κ), which is ∼1 W·m(-1) K(-1) for a-Si. However, recent work suggested that κ of micrometer-thick a-Si films can be greater than 3 W·m(-1) K(-1), which is contributed to by propagating vibrational modes, referred to as "propagons". However, precise determination of κ in a-Si has been elusive. Here, we used structures of a-Si nanotubes and suspended a-Si films that enabled precise in-plane thermal conductivity (κ∥) measurement within a wide thickness range of 5 nm to 1.7 μm. We showed unexpectedly high κ∥ in a-Si nanostructures, reaching ∼3.0 and 5.3 W·m(-1) K(-1) at ∼100 nm and 1.7 μm, respectively. Furthermore, the measured κ∥ is significantly higher than the cross-plane κ on the same films. This unusually high and anisotropic thermal conductivity in the amorphous Si nanostructure manifests the surprisingly broad propagon mean free path distribution, which is found to range from 10 nm to 10 μm, in the disordered and atomically isotropic structure. This result provides an unambiguous answer to the century-old problem regarding mean free path distribution of propagons and also sheds light on the design and performance of numerous a-Si based electronic and optoelectronic devices.

  4. Thermal Conductivity and Erosion Durability of Composite Two-Phase Air Plasma Sprayed Thermal Barrier Coatings

    Science.gov (United States)

    Schmitt, Michael P.; Rai, Amarendra K.; Zhu, Dongming; Dorfman, Mitchell R.; Wolfe, Douglas E.

    2015-01-01

    To enhance efficiency of gas turbines, new thermal barrier coatings (TBCs) must be designed which improve upon the thermal stability limit of 7 wt% yttria stabilized zirconia (7YSZ), approximately 1200 C. This tenant has led to the development of new TBC materials and microstructures capable of improved high temperature performance. This study focused on increasing the erosion durability of cubic zirconia based TBCs, traditionally less durable than the metastable t' zirconia based TBCs. Composite TBC microstructures composed of a low thermal conductivity/high temperature stable cubic Low-k matrix phase and a durable t' Low-k secondary phase were deposited via APS. Monolithic coatings composed of cubic Low-k and t' Low-k were also deposited, in addition to a 7YSZ benchmark. The thermal conductivity and erosion durability were then measured and it was found that both of the Low-k materials have significantly reduced thermal conductivities, with monolithic t' Low-k and cubic Low-k improving upon 7YSZ by approximately 13 and approximately 25%, respectively. The 40 wt% t' Low-k composite (40 wt% t' Low-k - 60 wt% cubic Low-k) showed a approximately 22% reduction in thermal conductivity over 7YSZ, indicating even at high levels, the t' Low-k secondary phase had a minimal impact on thermal in the composite coating. It was observed that a mere 20 wt% t' Low-k phase addition can reduce the erosion of a cubic Low-k matrix phase composite coating by over 37%. Various mixing rules were then investigated to assess this non-linear composite behavior and suggestions were made to further improve erosion durability.

  5. Role of Brownian Motion Hydrodynamics on Nanofluid Thermal Conductivity

    Energy Technology Data Exchange (ETDEWEB)

    W Evans, J Fish, P Keblinski

    2005-11-14

    We use a simple kinetic theory based analysis of heat flow in fluid suspensions of solid nanoparticles (nanofluids) to demonstrate that the hydrodynamics effects associated with Brownian motion have a minor effect on the thermal conductivity of the nanofluid. Our conjecture is supported by the results of molecular dynamics simulations of heat flow in a model nanofluid with well-dispersed particles. Our findings are consistent with the predictions of the effective medium theory as well as with recent experimental results on well dispersed metal nanoparticle suspensions.

  6. Prediction of thermal conductivity of sedimentary rocks from well logs

    DEFF Research Database (Denmark)

    Fuchs, Sven; Förster, Andrea

    2014-01-01

    . A common procedure in the latter approach is the use of empirical relations between TC and different petrophysical properties. Although numerous prediction equations were developed in the past five decades, none of these seem to be universally applicable for all major types of sedimentary rocks (clastics...... parameters (i.e. thermal conductivity, density, hydrogen index, sonic interval transit time, gamma-ray response, photoelectric factor) of artificial mineral assemblages consisting 15 rock-forming minerals that are used in different combinations to typify sedimentary rocks. The predictive capacity of the new...

  7. Thermal conductivity peaks in old and new ceramic superconductors

    Science.gov (United States)

    Williams, Wendell S.

    1993-07-01

    A sharp peak in the thermal conductivity curve of high Tc ceramic superconductors below Tc found by many workers is compared with a similar but even larger effect found earlier for niobium carbide — an older ceramic superconductor — by Radosevich and Williams. The interpretation of this peak given in the literature for the high Tc materials — reduced phonon-electron scattering below Tc as the superconducting energy gap opens — is the same as that established earlier for niobium carbide, which can be treated by BCS/BRT theory, thus lending support to this view. The role of point defects (vacancies) in both materials is also emphasized.

  8. Thermal conductivity calibration for hot wire based dc scanning thermal microscopy

    Science.gov (United States)

    Lefèvre, Stéphane; Volz, Sebastian; Saulnier, Jean-Bernard; Fuentes, Catherine; Trannoy, Nathalie

    2003-04-01

    Thermal conductivity characterization with nanoscale spatial resolution can be performed by contact probe techniques only. The technique based on a hot anemometer wire probe mounted in an atomic force microscope is now a standard setup. However, no rigorous calibration procedure is provided so far in basic dc mode. While in contact with the sample surface, the electrical current I injected into the probe is controlled so that electrical resistance or the wire temperature is maintained by the Joule effect. The variation in current is assumed to be linearly related to the heat flux lost towards the sample and traditional calibration is carried out by relating the thermal conductivity of a set of samples to the measured current I. We provide analytical and numerical thermal modeling of the tip and sample to estimate the key heat transfer in a conductivity calibration procedure. A simple calibration expression is established that provides thermal conductivity as a function of the probe current or voltage measured. Finally, experimental data allow us to determine the unknown quantities of the parametric form obtained, i.e., the mean tip-sample contact radius and conductance.

  9. How intermixing and anharmonicity enhances interfacial thermal conductance?

    Science.gov (United States)

    Polanco, Carlos; Zhang, Jingjie; Le, Nam; Rastgarkafshgarkolaei, Rouzbeh; Norris, Pamela; Ghosh, Avik

    2015-03-01

    The thermal conductance at an interface, whether ballistic or diffusive, can be expressed as a product of the number of conducting channels (M) and their average transmission (T). The common expectation is that interfacial defects reduce T and thus hurt the conductance. This is however at odds with recent simulations showing that a thin intermixing layer can in fact enhance the conductance. We argue that such an enhancement occurs when the increase in number of modes outweighs the reduction in their average transmission. The new channels open as a result of (a) the random interfacial structure that relaxes the conservation rules for the transverse momentum and promotes transitions between formerly symmetry disallowed channels; and (b) inelastic scattering through phonon-phonon interactions that allow modes beyond the contact cut-off frequency to contribute to transport. We use these results to build a back of the envelope model for interfacial conductance that depends on the mixing distribution, the anharmonic strength, the phonon polarization and wavelength. Non-Equilibrium Green's Function (NEGF) as well as Molecular Dynamics (MD) simulations on Si/mixed layer/Ge, as well as simpler FCC crystals support our results. NSF-CAREER (QMHP 1028883), NSF-IDR (CBET 1134311), XSEDE (TG-DMR130123).

  10. Improved approach for determining thin layer thermal conductivity using the 3ω method. Application to porous Si thermal conductivity in the temperature range 77-300 K

    Science.gov (United States)

    Valalaki, K.; Nassiopoulou, A. G.

    2017-05-01

    An improved approach for determining thermal conductivity using the 3ω method was used to determine anisotropic porous Si thermal conductivity in the temperature range 77-300 K. In this approach, thermal conductivity is extracted from experimental data of the third harmonic of the voltage (3ω) as a function of frequency, combined with consequent FEM simulations. The advantage is that within this approach the finite thickness of the sample and the heater are taken into account so that the corresponding errors introduced in thermal conductivity values when using Cahill’s simplified analytical formula are eliminated. The developed method constitutes a useful tool for measuring the thermal conductivity of samples with unknown thermal properties. The thermal conductivity measurements with the 3ω method are discussed and compared with those obtained using the well-established dc method.

  11. Moisture and Thermal Conductivity of Lightweight Block Walls

    Science.gov (United States)

    Joosep, R.

    2015-11-01

    This article examines thermal properties of lightweight block walls and their changes over the course of time. Three different types of lightweight blocks and two types of heat insulation are used in construction. Aeroc aerated concrete blocks are in use, as well as compacted LECA (Lightweight Expanded Clay Aggregate) Fibo blocks made from burned clay and Silbet blocks produced from oil shale ash. Expanded Thermisol EPS60F polystyrene plates and glass wool Isover OL-P plates are used for thermal insulation. The actual and computational values of thermal conductivity and the water draining properties of walls over time are compared in this article. Water draining from glass wool walls is relatively fast. Water-draining can take over a year in polystyrene insulated walls. All four wall constructions can be used as external walls, but care must be taken regarding the moisture content of the blocks during construction (the construction should be handled with care to minimise the moisture in the blocks), especially in polystyrene board-insulated walls.

  12. Thermal conductivity modeling of circular-wire nanocomposites

    Science.gov (United States)

    Hsieh, Tse-Yang; Yang, Jaw-Yen

    2010-08-01

    A phonon Boltzmann equation solver using multiblock-structured grid system is developed and applied to study transverse thermal transport in silicon-germanium circular-wire nanocomposite (silicon nanowires embedded in germanium host matrix). Past studies usually assume geometric simplification for the circular-wire nanocomposite, so the heat transfer is actually modeled in a square-wire nanocomposite. To demonstrate geometry effect, phonon transport in both the circular-wire and square-wire nanocomposites are investigated with various wire spacings, volume fractions, and dimensions. In ballistic phonon transport, due to the smoothness of circular shape, the circular wire imposes less thermal resistance than the square wire. Nevertheless, in the geometric simplification, the wire spacing of the square-wire nanocomposite is larger than that of the circular-wire nanocomposite. The usual geometric simplification can overestimate the thermal conductivity of the circular-wire nanocomposite. The obtained results can provide essential information for the development of bulk-nanostructured thermoelectric devices.

  13. Thermal and electrical conductivity of iron at Earth's core conditions

    CERN Document Server

    Pozzo, Monica; Gubbins, David; Alfè, Dario

    2012-01-01

    The Earth acts as a gigantic heat engine driven by decay of radiogenic isotopes and slow cooling, which gives rise to plate tectonics, volcanoes, and mountain building. Another key product is the geomagnetic field, generated in the liquid iron core by a dynamo running on heat released by cooling and freezing to grow the solid inner core, and on chemical convection due to light elements expelled from the liquid on freezing. The power supplied to the geodynamo, measured by the heat-flux across the core-mantle boundary (CMB), places constraints on Earth's evolution. Estimates of CMB heat-flux depend on properties of iron mixtures under the extreme pressure and temperature conditions in the core, most critically on the thermal and electrical conductivities. These quantities remain poorly known because of inherent difficulties in experimentation and theory. Here we use density functional theory to compute these conductivities in liquid iron mixtures at core conditions from first principles- the first directly comp...

  14. Thermal conductivity and interfacial conductance of AlN particle reinforced metal matrix composites

    Science.gov (United States)

    Kida, M.; Weber, L.; Monachon, C.; Mortensen, A.

    2011-03-01

    Aluminum nitride (AlN) particle reinforced metal-matrix-composites produced by pressure infiltration are characterized in terms of their thermal conductivity. The composites are designed to cover a wide range of phase contrast between the dispersed particles and the matrix; this is achieved by changing the matrix conductivity using Cu, Al, Sn, and Pb as the matrix. The interface thermal conductance (hc) between AlN and the matrix metals is determined by varying the size of the AlN particles using the Hasselman-Johnson approach and the differential effective medium (DEM) model to calculate hc from measured composite conductivity values. In addition, hc is measured directly at the AlN/Al interface using the transient thermoreflectance (TTR) method on thin aluminum layers deposited on flat AlN substrates to find good agreement with the value derived directly from Al/AlN composites of variable particle size and thus confirm the approach used here to measure hc. Data from the study show that hc at AlN-metal interfaces increases with the metal/AlN Debye temperature ratio; however, the increase is much less than predicted by currently accepted models.

  15. Electrical conductivity, thermal conductivity, and rheological properties of graphene oxide-based nanofluids

    Energy Technology Data Exchange (ETDEWEB)

    Hadadian, Mahboobeh; Goharshadi, Elaheh K., E-mail: gohari@ferdowsi.um.ac.ir [Ferdowsi University of Mashhad, Department of Chemistry (Iran, Islamic Republic of); Youssefi, Abbas [Par-e-Tavous Research Institute (Iran, Islamic Republic of)

    2014-12-15

    Highly stable graphene oxide (GO)-based nanofluids were simply prepared by dispersing graphite oxide with the average crystallite size of 20 nm, in polar base fluids without using any surfactant. Electrical conductivity, thermal conductivity, and rheological properties of the nanofluids were measured at different mass fractions and various temperatures. An enormous enhancement, 25,678 %, in electrical conductivity of distilled water was observed by loading 0.0006 mass fraction of GO at 25 °C. GO–ethylene glycol nanofluids exhibited a non-Newtonian shear-thinning behavior followed by a shear-independent region. This shear-thinning behavior became more pronounced at higher GO concentrations. The maximum ratio of the viscosity of nanofluid to that of the ethylene glycol as a base fluid was 3.4 for the mass fraction of 0.005 of GO at 20 °C under shear rate of 27.5 s{sup −1}. Thermal conductivity enhancement of 30 % was obtained for GO–ethylene glycol nanofluid for mass fraction of 0.07. The measurement of the transport properties of this new kind of nanofluid showed that it could provide an ideal fluid for heat transfer and electronic applications.

  16. Directional thermal conductivity of stator winding, endwinding, and iron core of small induction motor

    Energy Technology Data Exchange (ETDEWEB)

    Ha, K.P. [Seoul National University Graduate School, Seoul (Korea); Kauh, S.K. [Seoul National University, Seoul (Korea)

    1999-04-01

    Stator winding and endwinding are hot spots of a induction motor, and their temperature are heavily affected by the thermal conductivity of stator winding, endwinding and iron core. Hence, thermal conductivity evaluation of those materials is very important and the present study proposed prediction schemes for directional thermal conductivity of stator winding, endwinding, and iron core of a small induction motor. Longitudinal thermal conductivity of stator winding is evaluated by serial model, and transversal thermal conductivity is by Lewis and Nielson's model. Thermal conductivity of endwinding can be obtained by rotational transform of thermal conductivity tensor. And thermal conductivity of iron core is evaluated by serial model and parallel model. In the evaluation of the thermal conductivity of iron core, it was assumed that the contact resistance between the core plates plays 80% role in total resistance. This requires more detailed analysis. (author). 11 refs., 5 figs., 3 tabs.

  17. Techniques for Reducing Thermal Contact Resistance in Steady-State Thermal Conductivity Measurements on Polymer Composites

    Science.gov (United States)

    Stacey, C.; Simpkin, A. J.; Jarrett, R. N.

    2016-11-01

    The National Physical Laboratory (NPL) has developed a new variation on the established guarded hot plate technique for steady-state measurements of thermal conductivity. This new guarded hot plate has been specifically designed for making measurements on specimens with a thickness that is practical for advanced industrial composite materials and applications. During the development of this new guarded hot plate, NPL carried out an experimental investigation into methods for minimising the thermal contact resistance between the test specimen and the plates of the apparatus. This experimental investigation included tests on different thermal interface materials for use in another NPL facility based on a commercial guarded heat flow meter apparatus conforming to standard ASTM E1530-11. The results show the effect of applying different quantities of the type of heat transfer compound suggested in ASTM E1530-11 (clause 10.7.3) and also the effect on thermal resistance of alternative types of thermal interface products. The optimum quantities of two silicone greases were determined, and a silicone grease filled with copper was found to offer the best combination of repeatability, small hysteresis effect and a low thermal contact resistance. However, two products based on a textured indium foil and pyrolytic graphite sheet were found to offer similar or better reductions in thermal contact resistance, but with quicker, easier application and the advantages of protecting the apparatus plates from damage and being useable with specimen materials that would otherwise absorb silicone grease.

  18. Experimental thermal conductivity, thermal diffusivity, and specific heat values for mixtures of nitrogen, oxygen, and argon

    Science.gov (United States)

    Perkins, R. A.; Cieszkiewicz, M. T.

    1991-01-01

    Experimental measurements of thermal conductivity and thermal diffusivity obtained with a transient hot-wire apparatus are reported for three mixtures of nitrogen, oxygen, and argon. Values of the specific heat, Cp, are calculated from these measured values and the density calculated with an equation of state. The measurements were made at temperatures between 65 and 303 K with pressures between 0.1 and 70 MPa. The data cover the vapor, liquid, and supercritical gas phases for the three mixtures. The total reported points are 1066 for the air mixture (78.11 percent nitrogen, 20.97 percent oxygen, and 0.92 percent argon), 1058 for the 50 percent nitrogen, 50 percent oxygen mixture, and 864 for the 25 percent nitrogen, 75 oxygen mixture. Empirical thermal conductivity correlations are provided for the three mixtures.

  19. Measurements of thermal diffusivity, specific heat capacity and thermal conductivity with LFA 447 apparatus

    DEFF Research Database (Denmark)

    Zajas, Jan Jakub; Heiselberg, Per

    The LFA 447 can be successfully used for measurements of thermal diffusivity, specific heat and thermal conductivity of various samples. It is especially useful when determining the properties of materials on a very small scale. The matrix measurement mode allows for determining the local...... properties with a fine resolution, down to 1 millimeter. Special attention needs to be taken when determining the specific heat capacity in the comparative method. First of all, the test and reference sample should be of nearly identical thickness. Secondly, their heat diffusion time should be comparable, so...... that the heat losses from both samples during the measurement are similar. Finally, the leveling of the samples is very important. Very small discrepancies can cause a massive error in the derivation of specific heat capacity and, as a result, thermal conductivity....

  20. Effect of composition on thermal conductivity of silica insulation media.

    Science.gov (United States)

    Park, Sung; Kwon, Young-Pil; Kwon, Hyuk-Chon; Lee, Hae-Weon; Lee, Jae Chun

    2008-10-01

    Nano-sized fumed silica-based insulation media were prepared by adding TiO2 powders and ceramic fibers as opacifiers and structural integrity improvers, respectively. The high temperature thermal conductivities of the fumed silica-based insulation media were investigated using different types of TiO2 opacifier and by varying its content. The opacifying effects of nanostructured TiO2 powders produced by homogeneous precipitation process at low temperatures (HPPLT) were compared with those of commercial TiO2 powder. The nanostructured HPPLT TiO2 powder with a mean particle size of 1.8 microm was more effective to reduce radiative heat transfer than the commercial one with a similar mean particle size. The insulation samples with the HPPLT TiO2 powder showed about 46% lower thermal conductivity at temperatures of about 820 degrees C than those with the commercial one. This interesting result might be due to the more effective radiation scattering efficiency of the nanostructured HPPLT TiO2 powder which has better gap filling and coating capability in nano-sized composite compacts.